On the Impact Between a Water Free Surface and a Rigid Structure

NASA Astrophysics Data System (ADS)

Wang, An

In this thesis, the impact between a water surface and a structure is addressed in two related experiments. In the first experiment, the impact of a plunging breaking wave on a partially submerged 2D structure is studied. The evolution of the water surface profiles are measured with with a cinematic laser-induced flourescence technique, while the pressure distribution on the wall is measured simultaneously with an array of fast-response pressure sensors. When the structure is placed at a particular streamwise location in the wave tank and the bottom surface of the structure is located 13.3 cm below the mean water level, a ''flip-through'' impact occurs. In this case, the water surface profile between the crest and the front face of the structure is found to shrink to a point as the wave approaches the structure without breaking. High acceleration of the contact point motion is observed in this case. When the bottom of the structure is located at the mean water level, high-frequency pressure oscillations are observed. These pressure oscillations are believed to be caused by air that is entrapped near the wave crest during the impact process. When the bottom of the structure is sufficiently far above the mean water level, the first contact with the structure is the impact between the wave crest and the bottom corner of the structure. This latter condition, produces the largest impact pressures on the structure. In the second experiment, the slamming of a flat plate on a quiescent water surface is studied. A two-axis high-speed carriage is used to slam a flat plate on the water surface with high horizontal and vertical velocity. The above-mentioned LIF system is used to measure the evolution of the free surface adjacent to the plate. Measurements are performed with the horizontal and vertical carriage speeds ranging from zero to 6 m/s and 0.6 to 1.2 m/s, respectively, and the plate oriented obliquely to horizontal. Two types of splash are found, a spray of droplets and ligaments that is ejected horizontally from under the plate in the beginning of the impact process and a highly sloped spray sheet that is ejected later when the high edge of the plate moves below the water surface. Detailed measurements of these features are presented and simple models are used to interpret the data.

On the failure behaviour to striking bow penetration of impacted marine-steel structures

NASA Astrophysics Data System (ADS)

Prabowo, Aditya Rio; Muttaqie, Teguh; Sohn, Jung Min; Bae, Dong Myung; Setiyawan, Agus

2018-04-01

Demands for water transportation modes are continuously increasing as rapid economic and industrial growths in the recent decade. Ship as representative of the water transportation is generally needed to carry various products from one location to another. Besides as product carrier, ship also acts as public facility to transport human across islands for number of reasons, such as tourism and vehicle. Considering its importance, structural damage due to accidental loads or so-called impact can cause unacceptable casualties which threat ship passenger, shipping industry and maritime environment in same time. The most frequent impact phenomena occur in forms of collision and grounding, which are targeting side structure and double bottom consecutively. However, since responses of the impacts on structure are highly nonlinear and vary due to development of ship structures, sustainable analysis as an update of pioneer calculation can be beneficial as rational reference for improving safety and navigational instruments. This work aims to assess failures of the side structures subjected to penetration of striking bow in ship-ship collision scenario. Locations of impact are idealized to happen on after-end, midsection and fore-end to provide complete assessment. Striking bow is to be deployed by varying input velocity to observe significance of the fractures on the side structure. This configuration is implemented on the designed collision scenario, and later calculated using nonlinear finite element method (NLFEM). Summary of the solution indicated that the midsection produced the highest resistance against side collision. Breaching of the inner shell was successfully avoided on the fore-end, but the critical damage to the cargo was observed during bow penetration to the after-end region. This location was recommended to be added by longitudinal framing to increase its resistance against ship collision.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neitzel, D.A.; McKenzie, D.H.

To minimize adverse impact on aquatic ecosystems resulting from the operation of water intake structures, design engineers must have relevant information on the behavior, physiology and ecology of local fish and shellfish. Identification of stimulus/response relationships and the environmental factors that influence them is the first step in incorporating biological information in the design, location or modification of water intake structures. A procedure is presented in this document for providing biological input to engineers who are designing, locating or modifying a water intake structure. The authors discuss sources of stimuli at water intakes, historical approaches in assessing potential/actual impact andmore » review biological information needed for intake design.« less

Impact source localisation in aerospace composite structures

NASA Astrophysics Data System (ADS)

De Simone, Mario Emanuele; Ciampa, Francesco; Boccardi, Salvatore; Meo, Michele

2017-12-01

The most commonly encountered type of damage in aircraft composite structures is caused by low-velocity impacts due to foreign objects such as hail stones, tool drops and bird strikes. Often these events can cause severe internal material damage that is difficult to detect and may lead to a significant reduction of the structure’s strength and fatigue life. For this reason there is an urgent need to develop structural health monitoring systems able to localise low-velocity impacts in both metallic and composite components as they occur. This article proposes a novel monitoring system for impact localisation in aluminium and composite structures, which is able to determine the impact location in real-time without a-priori knowledge of the mechanical properties of the material. This method relies on an optimal configuration of receiving sensors, which allows linearization of well-known nonlinear systems of equations for the estimation of the impact location. The proposed algorithm is based on the time of arrival identification of the elastic waves generated by the impact source using the Akaike Information Criterion. The proposed approach was demonstrated successfully on both isotropic and orthotropic materials by using a network of closely spaced surface-bonded piezoelectric transducers. The results obtained show the validity of the proposed algorithm, since the impact sources were detected with a high level of accuracy. The proposed impact detection system overcomes current limitations of other methods and can be retrofitted easily on existing aerospace structures allowing timely detection of an impact event.

Network Structure as a Modulator of Disturbance Impacts in Streams

NASA Astrophysics Data System (ADS)

Warner, S.; Tullos, D. D.

2017-12-01

This study examines how river network structure affects the propagation of geomorphic and anthropogenic disturbances through streams. Geomorphic processes such as debris flows can alter channel morphology and modify habitat for aquatic biota. Anthropogenic disturbances such as road construction can interact with the geomorphology and hydrology of forested watersheds to change sediment and water inputs to streams. It was hypothesized that the network structure of streams within forested watersheds would influence the location and magnitude of the impacts of debris flows and road construction on sediment size and channel width. Longitudinal surveys were conducted every 50 meters for 11 kilometers of third-to-fifth order streams in the H.J. Andrews Experimental Forest in the Western Cascade Range of Oregon. Particle counts and channel geometry measurements were collected to characterize the geomorphic impacts of road crossings and debris flows as disturbances. Sediment size distributions and width measurements were plotted against the distance of survey locations through the network to identify variations in longitudinal trends of channel characteristics. Thresholds for the background variation in sediment size and channel width, based on the standard deviations of sample points, were developed for sampled stream segments characterized by location as well as geomorphic and land use history. Survey locations were classified as "disturbed" when they deviated beyond the reference thresholds in expected sediment sizes and channel widths, as well as flow-connected proximity to debris flows and road crossings. River network structure was quantified by drainage density and centrality of nodes upstream of survey locations. Drainage density and node centrality were compared between survey locations with similar channel characteristic classifications. Cluster analysis was used to assess the significance of survey location, proximity of survey location to debris flows and road crossings, drainage density and node centrality in predicting sediment size and channel width classifications for locations within the watershed. Results contribute to the understanding of susceptibility and responses of streams supporting critical habitat for aquatic species to debris flows and forest road disturbances.

A geophysical investigation of the northeastern rim of the St. Martin impact structure, Manitoba, Canada

NASA Astrophysics Data System (ADS)

Zivkovic, Vladimir B.

The St. Martin impact structure is a 40 Km diameter structure located in Manitoba, Canada lies in featureless, glaciated terrain lacking any surface expression of an impact structure. The age of the structure has been re-determined to range between 224.3 Ma to 241.4 Ma which nullified a previous hypothesis suggesting this impact was part of a multiple impact event. Within the proposed structural boundary two outcrops of Archean granite are present. The first outcrop is located in what has been identified as the central peak of the impact structure. The second outcrop lies along the northeastern boundary and is known locally as Big Rock. The purpose of this investigation was to determine the relationship of Big Rock, if any, to the impact event and to constrain a more accurate diameter of the structure. To accomplish this I conducted two geophysical surveys and used selected data from a previous survey. The two methods I conducted were: a magnetic survey and seismic reflection profiling. Selected data from a previous gravity survey was used to supplement survey results. The magnetic survey was conducted using the total field G-856 Memory-Mag proton precession magnetometer which measures local or regional field strength. The seismic reflection survey was conducted using three Geometrics Geode exploration seismographs. Due to the complexity of seismic data processing I retained an outside seismic data processing company. Previous gravity anomaly data were acquired using a LaCoste and Romberg Model G gravimeter. The results of this geophysical investigation reveal a shallowing of granitic basement rock with exposure near Big Rock. However, a suggested listric fault near Big Rock was not identified via seismic reflection profiling, but was suggested by both the gravity and magnetic surveys. Listric faults that are genetically related to impact structures are also indicative of the structure's outer boundary and therefore can confirm that the St. Martin impact structure is indeed 40 Km in diameter.

Rewinding the waves: tracking underwater signals to their source.

PubMed

Kadri, Usama; Crivelli, Davide; Parsons, Wade; Colbourne, Bruce; Ryan, Amanda

2017-10-24

Analysis of data, recorded on March 8th 2014 at the Comprehensive Nuclear-Test-Ban Treaty Organisation's hydroacoustic stations off Cape Leeuwin Western Australia, and at Diego Garcia, reveal unique pressure signatures that could be associated with objects impacting at the sea surface, such as falling meteorites, or the missing Malaysian Aeroplane MH370. To examine the recorded signatures, we carried out experiments with spheres impacting at the surface of a water tank, where we observed almost identical pressure signature structures. While the pressure structure is unique to impacting objects, the evolution of the radiated acoustic waves carries information on the source. Employing acoustic-gravity wave theory we present an analytical inverse method to retrieve the impact time and location. The solution was validated using field observations of recent earthquakes, where we were able to calculate the eruption time and location to a satisfactory degree of accuracy. Moreover, numerical validations confirm an error below 0.02% for events at relatively large distances of over 1000 km. The method can be developed to calculate other essential properties such as impact duration and geometry. Besides impacting objects and earthquakes, the method could help in identifying the location of underwater explosions and landslides.

Ash Shutbah: A possible impact structure in Saudi Arabia

NASA Astrophysics Data System (ADS)

Gnos, Edwin; Hofmann, Beda A.; Schmieder, Martin; Al-Wagdani, Khalid; Mahjoub, Ayman; Al-Solami, Abdulaziz A.; Habibullah, Siddiq N.; Matter, Albert; Alwmark, Carl

2014-10-01

We have investigated the Ash Shutbah circular structure in central Saudi Arabia (21°37'N 45°39'E) using satellite imagery, field mapping, thin-section petrography, and X-ray diffraction of collected samples. The approximately 2.1 km sized structure located in flat-lying Jurassic Tuwaiq Mountain Limestone has been nearly peneplained by erosional processes. Satellite and structural data show a central area consisting of Dhruma Formation sandstones with steep bedding and tight folds plunging radially outward. Open folding occurs in displaced, younger Tuwaiq Mountain Limestone Formation blocks surrounding the central area, but is absent outside the circular structure. An approximately 60 cm thick, unique folded and disrupted orthoquartzitic sandstone marker bed occurring in the central area of the structure is found 140 m deeper in undisturbed escarpment outcrops located a few hundred meters west of the structure. With exception of a possible concave shatter cone found in the orthoquartzite of the central area, other diagnostic shock features are lacking. Some quartz-rich sandstones from the central area show pervasive fracturing of quartz grains with common concussion fractures. This deformation was followed by an event of quartz dissolution and calcite precipitation consistent with local sea- or groundwater heating. The combination of central stratigraphic uplift of 140 m, concussion features in discolored sandstone, outward-dipping concentric folds in the central area, deformation restricted to the rocks of the ring structure, a complex circular structure of 2.1 km diameter that appears broadly consistent with what one would expect from an impact structure in sedimentary targets, and a possible shatter cone all point to an impact origin of the Ash Shutbah structure. In fact, the Ash Shutbah structure appears to be a textbook example of an eroded, complex impact crater located in flat-lying sedimentary rocks, where the undisturbed stratigraphic section can be studied in escarpment outcrops in the vicinity of the structure.

An analysis of penetration and ricochet phenomena in oblique hypervelocity impact

NASA Technical Reports Server (NTRS)

Schonberg, William P.; Taylor, Roy A.; Horn, Jennifer R.

1988-01-01

An experimental investigation of phenomena associated with the oblique hypervelocity impact of spherical projectiles on multisheet aluminum structures is described. A model that can be employed in the design of meteoroid and space debris protection systems for space structures is developed. The model consists of equations that relate crater and perforation damage of a multisheet structure to parameters such as projectile size, impact velocity, and trajectory obliquity. The equations are obtained through a regression analysis of oblique hypervelocity impact test data. This data shows that the response of a multisheet structure to oblique impact is significantly different from its response to normal hypervelocity impact. It was found that obliquely incident projectiles produce ricochet debris that can severely damage panels or instrumentation located on the exterior of a space structure. Obliquity effects of high-speed impact must, therefore, be considered in the design of any structure exposed to the meteoroid and space debris environment.

An impact source localization technique for a nuclear power plant by using sensors of different types.

PubMed

Choi, Young-Chul; Park, Jin-Ho; Choi, Kyoung-Sik

2011-01-01

In a nuclear power plant, a loose part monitoring system (LPMS) provides information on the location and the mass of a loosened or detached metal impacted onto the inner surface of the primary pressure boundary. Typically, accelerometers are mounted on the surface of a reactor vessel to localize the impact location caused by the impact of metallic substances on the reactor system. However, in some cases, the number of accelerometers is not sufficient to estimate the impact location precisely. In such a case, one of useful methods is to utilize other types of sensor that can measure the vibration of the reactor structure. For example, acoustic emission (AE) sensors are installed on the reactor structure to detect leakage or cracks on the primary pressure boundary. However, accelerometers and AE sensors have a different frequency range. The frequency of interest of AE sensors is higher than that of accelerometers. In this paper, we propose a method of impact source localization by using both accelerometer signals and AE signals, simultaneously. The main concept of impact location estimation is based on the arrival time difference of the impact stress wave between different sensor locations. However, it is difficult to find the arrival time difference between sensors, because the primary frequency ranges of accelerometers and AE sensors are different. To overcome the problem, we used phase delays of an envelope of impact signals. This is because the impact signals from the accelerometer and the AE sensor are similar in the whole shape (envelope). To verify the proposed method, we have performed experiments for a reactor mock-up model and a real nuclear power plant. The experimental results demonstrate that we can enhance the reliability and precision of the impact source localization. Therefore, if the proposed method is applied to a nuclear power plant, we can obtain the effect of additional installed sensors. Crown Copyright © 2010. Published by Elsevier Ltd. All rights reserved.

NASA experiments onboard the controlled impact demonstration

NASA Technical Reports Server (NTRS)

Hayduk, R. J.; Alfaro-Bou, E.; Fasanella, E. L.

1985-01-01

The structural crashworthiness tests conducted by NASA on the December 1, 1984 controlled impact demonstration are discussed. The components and locations of the data acquisition and photographic systems developed by NASA to evaluate impact loads throughout the aircraft structure and the transmission of loads into the dummies are described. The effectiveness of the NASA designed absorbing seats and the vertical, longitudinal, and transverse impact loads are measured. Data that is extremely applicable to crash dynamics structural research was obtained by the data acquisition system and very low load levels were measured for the NASA energy absorbing seats.

Australian Aboriginal Geomythology: Eyewitness Accounts of Cosmic Impacts?

NASA Astrophysics Data System (ADS)

Hamacher, Duane W.; Norris, Ray P.

2009-12-01

Descriptions of cosmic impacts and meteorite falls are found throughout Australian Aboriginal oral traditions. In some cases, these texts describe the impact event in detail, sometimes citing the location, suggesting that the events were witnessed. We explore whether cosmic impacts and meteorite falls may have been witnessed by Aboriginal Australians and incorporated into their oral traditions. We discuss the complications and bias in recording and analysing oral texts but suggest that these texts may be used both to locate new impact structures or meteorites and model observed impact events. We find that, while detailed Aboriginal descriptions of cosmic impacts are abundant in the literature, there is currently no physical evidence connecting these accounts to impact events currently known to Western science.

Determination of barge impact probabilities for bridge design : [summary].

DOT National Transportation Integrated Search

2016-04-01

University of Florida researchers developed a revised barge impact probability expression applicable for the design of bridge structures located on Florida waterways. University of Florida researchers obtained barge flotilla traffic data and barge-to...

Seismicity of the St. Lawrence paleorift faults overprinted by a meteorite impact crater: Implications for crustal strength based on new earthquake relocations in the Charlevoix Seismic Zone, Eastern Canada

NASA Astrophysics Data System (ADS)

Yu, H.; Harrington, R. M.; Liu, Y.; Lamontagne, M.; Pang, M.

2015-12-01

The Charlevoix Seismic Zone (CSZ), located along the St. Lawrence River (SLR) ~100 km downstream from Quebec City, is the most active seismic zone in eastern Canada with five historic earthquakes of M 6-7 and ~ 200 events/year reported by the Canadian National Seismograph Network. Cataloged earthquake epicenters outline two broad linear zones along the SLR with little shallow seismicity in between. Earthquakes form diffuse clusters between major dipping faults rather than concentrating on fault planes. Detailed fault geometry in the CSZ is uncertain and the effect on local seismicity of a meteorite impact structure that overprints the paleorift faults remains ambiguous. Here we relocate 1639 earthquakes occurring in the CSZ between 01/1988 - 10/2010 using the double-difference relocation method HypoDD and waveforms primarily from 7 local permanent stations. We use the layered SLR north shore velocity model from Lamontagne (1999), and travel time differences based on both catalog and cross-correlated P and S-phase picks. Of the 1639 relocated earthquakes, 1236 (75.4%) satisfied selection criteria of horizontal and vertical errors less than 2 km and 1 km respectively. Cross-sections of relocated seismicity show hypocenters along distinct active fault segments. Earthquakes located beneath the north shore of the SLR are likely correlated with the NW Gouffre fault, forming a ~10 km wide seismic zone parallel to the river, with dip angle changing to near vertical at the northern edge of the impact zone. In contrast, seismicity beneath the SLR forms a diffuse cloud within the impact structure, likely representing a highly fractured volume. It further implies that faults could be locally weak and subject to high pore-fluid pressures. Seismicity outside the impact structure defines linear structures aligning with the Charlevoix fault. Relocated events of M > 4 all locate outside the impact structure, indicating they nucleated on the NE-SW-oriented paleorift faults.

Quasi-Static Compression and Low-Velocity Impact Behavior of Tri-Axial Bio-Composite Structural Panels Using a Spherical Head

PubMed Central

Li, Jinghao; Hunt, John F; Gong, Shaoqin; Cai, Zhiyong

2017-01-01

This paper presents experimental results of both quasi-static compression and low-velocity impact behavior for tri-axial bio-composite structural panels using a spherical load head. Panels were made having different core and face configurations. The results showed that panels made having either carbon fiber fabric composite faces or a foam-filled core had significantly improved impact and compressive performance over panels without either. Different localized impact responses were observed based on the location of the compression or impact relative to the tri-axial structural core; the core with a smaller structural element had better impact performance. Furthermore, during the early contact phase for both quasi-static compression and low-velocity impact tests, the panels with the same configuration had similar load-displacement responses. The experimental results show basic compression data could be used for the future design and optimization of tri-axial bio-composite structural panels for potential impact applications. PMID:28772542

Force Criterion Prediction of Damage for Carbon/Epoxy Composite Panels Impacted by High Velocity Ice

NASA Astrophysics Data System (ADS)

Rhymer, Jennifer D.

The use of advanced fiber-reinforced polymer matrix composites in load-bearing aircraft structures is increasing, as evident by the various composites-intensive transport aircraft presently under development. A major impact source of concern for these structures is hail ice, which affects design and skin-sizing (skin thickness determination) at various locations of the aircraft. Impacts onto composite structures often cause internal damage that is not visually detectable due to the high strength and resiliency of the composite material (unlike impacts onto metallic structures). This internal damage and its effect on the performance of the structure are of great concern to the aircraft industry. The prediction of damage in composite structures due to SHI impact has been accomplished via experimental work, explicit dynamic nonlinear finite element analysis (FEA) and the definition of design oriented relationships. Experiments established the critical threshold and corresponding analysis provided contact force results not readily measurable in high velocity SHI impact experiments. The design oriented relationships summarize the FEA results and experimental database into contact force estimation curves that can be easily applied for damage prediction. Failure thresholds were established for the experimental conditions (panel thickness ranging from 1.56 to 4.66 mm and ice diameters from 38.1 to 61.0 mm). Additionally, the observations made by high-speed video during the impact event, and ultrasonic C-scan post-impact, showed how the ice failed during impact and the overall shape and location of the panel damage. Through analysis, the critical force, the force level where damage occurs above but not below, of a SHI impact onto the panel was found to be dependent only on the target structure. However, the peak force generated during impact was dependent on both the projectile and target. Design-oriented curves were generated allowing the prediction of the allowable velocity for given SHI diameter impact onto a known panel in order to estimated damage. Finally, a scaling relationship was established to predict the peak force developed onto composite panels impacted by SHI. This is useful in reducing the amount of experimental investigations, or computationally expensive simulation work, that would otherwise need to be performed to obtain these results.

Motor abundance and control structure in the golf swing.

PubMed

Morrison, A; McGrath, D; Wallace, E S

2016-04-01

Variability and control structure are under-represented areas of golf swing research. This study investigated the use of the abundant degrees of freedom in the golf swing of high and intermediate skilled golfers using uncontrolled manifold (UCM) analysis. The variance parallel to (VUCM) and orthogonal to (VOrth) the UCM with respect to the orientation and location of the clubhead were calculated. The higher skilled golfers had proportionally higher values of VUCM than lower skilled players for all measured outcome variables. Motor synergy was found in the control of the orientation of the clubhead and the combined outcome variables but not for clubhead location. Clubhead location variance zeroed-in on impact as has been previously shown, whereas clubhead orientation variance increased near impact. Both skill levels increased their control over the clubhead location leading up to impact, with more control exerted over the clubhead orientation in the early downswing. The results suggest that to achieve higher skill levels in golf may not lie simply in optimal technique, but may lie more in developing control over the abundant degrees of freedom in the body. Copyright © 2016 Elsevier B.V. All rights reserved.

Structural monitoring for rare events in remote locations

NASA Astrophysics Data System (ADS)

Hale, J. M.

2005-01-01

A structural monitoring system has been developed for use on high value engineering structures, which is particularly suitable for use in remote locations where rare events such as accidental impacts, seismic activity or terrorist attack might otherwise go undetected. The system comprises a low power intelligent on-site data logger and a remote analysis computer that communicate with one another using the internet and mobile telephone technology. The analysis computer also generates e-mail alarms and maintains a web page that displays detected events in near real-time to authorised users. The application of the prototype system to pipeline monitoring is described in which the analysis of detected events is used to differentiate between impacts and pressure surges. The system has been demonstrated successfully and is ready for deployment.

Structural impact detection with vibro-haptic interfaces

NASA Astrophysics Data System (ADS)

Jung, Hwee-Kwon; Park, Gyuhae; Todd, Michael D.

2016-07-01

This paper presents a new sensing paradigm for structural impact detection using vibro-haptic interfaces. The goal of this study is to allow humans to ‘feel’ structural responses (impact, shape changes, and damage) and eventually determine health conditions of a structure. The target applications for this study are aerospace structures, in particular, airplane wings. Both hardware and software components are developed to realize the vibro-haptic-based impact detection system. First, L-shape piezoelectric sensor arrays are deployed to measure the acoustic emission data generated by impacts on a wing. Unique haptic signals are then generated by processing the measured acoustic emission data. These haptic signals are wirelessly transmitted to human arms, and with vibro-haptic interface, human pilots could identify impact location, intensity and possibility of subsequent damage initiation. With the haptic interface, the experimental results demonstrate that human could correctly identify such events, while reducing false indications on structural conditions by capitalizing on human’s classification capability. Several important aspects of this study, including development of haptic interfaces, design of optimal human training strategies, and extension of the haptic capability into structural impact detection are summarized in this paper.

Combining shock barometry with numerical modeling: Insights into complex crater formation—The example of the Siljan impact structure (Sweden)

NASA Astrophysics Data System (ADS)

Holm-Alwmark, Sanna; Rae, Auriol S. P.; Ferrière, Ludovic; Alwmark, Carl; Collins, Gareth S.

2017-12-01

Siljan, central Sweden, is the largest known impact structure in Europe. It was formed at about 380 Ma, in the late Devonian period. The structure has been heavily eroded to a level originally located underneath the crater floor, and to date, important questions about the original size and morphology of Siljan remain unanswered. Here we present the results of a shock barometry study of quartz-bearing surface and drill core samples combined with numerical modeling using iSALE. The investigated 13 bedrock granitoid samples show that the recorded shock pressure decreases with increasing depth from 15 to 20 GPa near the (present) surface, to 10-15 GPa at 600 m depth. A best-fit model that is consistent with observational constraints relating to the present size of the structure, the location of the downfaulted sediments, and the observed surface and vertical shock barometry profiles is presented. The best-fit model results in a final crater (rim-to-rim) diameter of 65 km. According to our simulations, the original Siljan impact structure would have been a peak-ring crater. Siljan was formed in a mixed target of Paleozoic sedimentary rocks overlaying crystalline basement. Our modeling suggests that, at the time of impact, the sedimentary sequence was approximately 3 km thick. Since then, there has been around 4 km of erosion of the structure.

The Impact of Model Uncertainty on Spatial Compensation in Structural Acoustic Control

NASA Technical Reports Server (NTRS)

Clark, Robert L.

2005-01-01

Turbulent boundary layer (TBL) noise is considered a primary contribution to the interior noise present in commercial airliners. There are numerous investigations of interior noise control devoted to aircraft panels; however, practical realization is a potential challenge since physical boundary conditions are uncertain at best. In most prior studies, pinned or clamped boundary conditions were assumed; however, realistic panels likely display a range of boundary conditions between these two limits. Uncertainty in boundary conditions is a challenge for control system designers, both in terms of the compensator implemented and the location of transducers required to achieve the desired control. The impact of model uncertainties, specifically uncertain boundaries, on the selection of transducer locations for structural acoustic control is considered herein. The final goal of this work is the design of an aircraft panel structure that can reduce TBL noise transmission through the use of a completely adaptive, single-input, single-output control system. The feasibility of this goal is demonstrated through the creation of a detailed analytical solution, followed by the implementation of a test model in a transmission loss apparatus. Successfully realizing a control system robust to variations in boundary conditions can lead to the design and implementation of practical adaptive structures that could be used to control the transmission of sound to the interior of aircraft. Results from this research effort indicate it is possible to optimize the design of actuator and sensor location and aperture, minimizing the impact of boundary conditions on the desired structural acoustic control.

ENSO and anthropogenic impacts on phytoplankton diversity in tropical coastal waters

NASA Astrophysics Data System (ADS)

Doan-Nhu, Hai; Nguyen-Ngoc, Lam; Nguyen, Chi-Thoi

2016-01-01

16-year phytoplankton data were analysed to assess ENSO and anthropogenic impacts on biodiversity and community structure at 3 locations (Nha-Trang and Phan-Thiet Bays and near Phu-Qui Island) in South Centre Viet Nam to understand (1) the primary scales of change in phytoplankton community structure, and traditional and taxonomic diversity indices; (2) the significance of environmental changes and/or climate variability on phytoplankton diversity; and (3) the usefulness of these long-term data for analysing future impacts of anthropogenic and climate changes. Traditional and taxonomic diversity indices were compared and tested in linkage with environmental conditions and ENSO. Nutrient data indicated stronger environmental impacts in Phan-Thiet Bay, milder in Nha-Trang Bay and less noticeable near Phu-Qui Island. There were measurable impacts of both anthropogenic and ENSO on phytoplankton at different locations in various parameters, e.g. species number, diversity and community structures. The lowest diversity was recorded in the most anthropogenically impacted site, Phan-Thiet Bay. Although a stronger impact on phytoplankton was recorded in ENSO year in Phan Thiet Bay, quantitative separation between anthropogenic and ENSO impacts using phytoplankton biodiversity indices was impossible. In the waters with less anthropogenic impacts, ENSO effects on taxonomic diversity was better indicated by negative phytoplankton responses to the ONI index (Nha-Trang Bay) and recovery of phytoplankton after the ENSO events (near Phu-Qui Island). Among the diversity indices, the taxonomic diversity indices (e.g. Δ+ and Λ+) better described impacts of ENSO than the traditional ones.

Evidence for a Putative Impact Structure in Palm Valley, Central Australia

NASA Astrophysics Data System (ADS)

Hamacher, D. W.; O'Neill, C.; Buchel, A.; Britton, T. R.

2010-07-01

Introduction: We present evidence supporting the impact origin of a circular structure located in Palm Valley, Central Australia (24° 03' 06'' S, 132° 42' 34'' E). The ~280 m wide structure was discovered using a combination of Google Maps and a local Arrernte Aboriginal oral tradition regarding a star that fell into a waterhole called Puka in Palm Valley, Northern Territory [1][2] (see [3] for details of the discovery). Geophysical Evidence: A survey of the structure in September 2009 collected magnetic, gravity and topographic data. Geophysical modeling of the data revealed the structure has a bowl-shaped subsurface morphology, as expected for a simple impact crater. Though the structure sits within the Finke Gorge system, the models do not support an erosional origin for the structure, as no buried channels are observed. Nor does the modeling fit a volcanic origin, as the density structure at depth is consistent with fractured sandstone/sediments. Geological Evidence: One channel runs out of the crater to the south, consistent with outflow from crater-filling events, but again not with an erosional origin for the structure itself. The microstructure of rock samples collected from the site revealed the presence of planar deformation features in the quartz grains. The coincident angle of the fractures is consistent with the crystallographic fracture directions under mild-end shocks. These grains probably represent local focusing of stress as the shock wave moved through the heterogeneous grain matrix, suggesting the conditions were right for the shock pressure to locally exceed the ~7.5 GPa required to form the features, even though the bulk of the shock pressure was much less. Conclusion: Based on the level of erosion and the absence of shatter cones and meteorite fragments, we estimate the structure's age to be in the millions of years. While the presence of shocked-quartz is a direct indicator of a cosmic impact, we cannot rule out that the quartz was transported from an older structure into the Hermannsburg sandstone as it was deposited. The ~22 km wide Gosse's Bluff impact structure, located ~40 km from Palm Valley, postdates the Hermannsburg sandstone, leaving a distal unidentified impact event as a possibility. However, the bowl shaped morphology of the Palm Valley structure, as well as the fractures on the structure's walls, support an impact origin. References: [1] Austin-Broos, D., 2009, "Arrernte Past, Arrernte Present", University of Chicago Press, pp. 37-38. [2] Róheim, G., 1945, "The Eternal Ones of the Dream: a psychoanalytic interpretation of Australian myth and ritual", International Universities Press, New York, p. 183. [3] Hamacher, D.W. & Norris, R.P., 2010, Using Aboriginal Oral Traditions to locate meteorite falls and impact craters. In Ilgarijiri - things belonging to the sky, edited by R.P. Norris, Proceedings of the symposium on Indigenous Astronomy held on 27 November 2009 at Australian Institute for Aboriginal and Torres Strait Islander Studies, Canberra, Australia (in press).

Impact damage resistance of composite fuselage structure, part 1

NASA Technical Reports Server (NTRS)

Dost, E. F.; Avery, W. B.; Ilcewicz, L. B.; Grande, D. H.; Coxon, B. R.

1992-01-01

The impact damage resistance of laminated composite transport aircraft fuselage structures was studied experimentally. A statistically based designed experiment was used to examine numerous material, laminate, structural, and extrinsic (e.g., impactor type) variables. The relative importance and quantitative measure of the effect of each variable and variable interactions on responses including impactor dynamic response, visibility, and internal damage state were determined. The study utilized 32 three-stiffener panels, each with a unique combination of material type, material forms, and structural geometry. Two manufacturing techniques, tow placement and tape lamination, were used to build panels representative of potential fuselage crown, keel, and lower side-panel designs. Various combinations of impactor variables representing various foreign-object-impact threats to the aircraft were examined. Impacts performed at different structural locations within each panel (e.g., skin midbay, stiffener attaching flange, etc.) were considered separate parallel experiments. The relationship between input variables, measured damage states, and structural response to this damage are presented including recommendations for materials and impact test methods for fuselage structure.

A novel real-time health monitoring system for unmanned vehicles

NASA Astrophysics Data System (ADS)

Zhang, David C.; Ouyang, Lien; Qing, Peter; Li, Irene

2008-04-01

Real-time monitoring the status of in-service structures such as unmanned vehicles can provide invaluable information to detect the damages to the structures on time. The unmanned vehicles can be maintained and repaired in time if such damages are found. One typical cause of damages of unmanned vehicles is from impacts caused by bumping into some obstacles or being hit by some objects such as hostile fire. This paper introduces a novel impact event sensing system that can detect the location of the impact events and the force-time history of the impact events. The system consists of the Piezo-electric sensor network, the hardware platform and the analysis software. The new customized battery-powered impact event sensing system supports up to 64-channel parallel data acquisition. It features an innovative low-power hardware trigger circuit that monitors 64 channels simultaneously. The system is in the sleep mode most of the time. When an impact event happens, the system will wake up in micro-seconds and detect the impact location and corresponding force-time history. The system can be combined with the SMART sensing system to further evaluate the impact damage severity.

Locating air leaks in manned spacecraft using structure-borne noise.

PubMed

Holland, Stephen D; Chimenti, D E; Roberts, Ron; Strei, Michael

2007-06-01

All manned spacecraft are vulnerable to leaks generated by micrometeorite or debris impacts. Methods for locating such leaks using leak-generated, structure-borne ultrasonic noise are discussed and demonstrated. Cross-correlations of ultrasonic noise waveforms from a leak into vacuum are used to find the location of the leak. Four methods for sensing and processing leak noise have been developed and tested and each of these can be used to reveal the leak location. The methods, based on phased-array, distributed sensor, and dual sensor approaches, utilize the propagation patterns of guided ultrasonic Lamb waves in the spacecraft skin structure to find the source or direction of the leak noise. It is shown that each method can be used to successfully locate the leak to within a few millimeters on a 0.6-m2 aluminum plate. The relative merits of the four methods are discussed.

Proof of Concept of Impact Detection in Composites Using Fiber Bragg Grating Arrays

PubMed Central

Gomez, Javier; Jorge, Iagoba; Durana, Gaizka; Arrue, Jon; Zubia, Joseba; Aranguren, Gerardo; Montero, Ander; López, Ion

2013-01-01

Impact detection in aeronautical structures allows predicting their future reliability and performance. An impact can produce microscopic fissures that could evolve into fractures or even the total collapse of the structure, so it is important to know the location and severity of each impact. For this purpose, optical fibers with Bragg gratings are used to analyze each impact and the vibrations generated by them. In this paper it is proven that optical fibers with Bragg gratings can be used to detect impacts, and also that a high-frequency interrogator is necessary to collect valuable information about the impacts. The use of two interrogators constitutes the main novelty of this paper. PMID:24021969

Results of Prospecting of Impact Craters in Morocco

NASA Astrophysics Data System (ADS)

Chaabout, S.; Chennaoui Aoudjehane, H.; Reimold, W. U.; Baratoux, D.

2014-09-01

This work is based to use satellite images of Google Earth and Yahoo-Maps scenes; we examined the surface of our country to be able to locate the structures that have a circular morphology such as impact craters, which potentially could be.

Probability of Detection Study on Impact Damage to Honeycomb Composite Structure using Thermographic Inspection

NASA Technical Reports Server (NTRS)

Hodge, Andrew J.; Walker, James L., II

2008-01-01

A probability of detection study was performed for the detection of impact damage using flash heating infrared thermography on a full scale honeycomb composite structure. The honeycomb structure was an intertank structure from a previous NASA technology demonstration program. The intertank was fabricated from IM7/8552 carbon fiber/epoxy facesheets and aluminum honeycomb core. The intertank was impacted in multiple locations with a range of impact energies utilizing a spherical indenter. In a single blind study, the intertank was inspected with thermography before and after impact damage was incurred. Following thermographic inspection several impact sites were sectioned from the intertank and cross-sectioned for microscopic comparisons of NDE detection and actual damage incurred. The study concluded that thermographic inspection was a good method of detecting delamination damage incurred by impact. The 90/95 confidence level on the probability of detection was close to the impact energy that delaminations were first observed through cross-sectional analysis.

A Re-Examination of the Bedout High, Offshore Canning Basin, Western Australia - Possible Impact Site for the Permian-Triassic Mass Extinction Event?

NASA Astrophysics Data System (ADS)

Becker, L.; Nicholson, C.; Poreda, R. J.

2002-12-01

The Bedout High, located offshore Canning basin in Western Australia, is an unusual structure and its origin remains problematic. K-Ar dating of volcanic samples encountered at total depth in the Lagrange-1 exploration well indicated an age of about 253+/-5 Ma consistent with the Permian-Triassic boundary event. Gorter (PESA News, pp. 33-34, 1996) speculates that the Bedout High is the uplifted core (30 km) of a circular feature, some 220 km across, formed by the impact of a large bolide (cometary or asteroidal) with the Earth near the end-Permian. Accepting a possible impact origin for the Bedout structure, with the indicated dimensions, would have had profound effects on global climate as well as significant changes in lithotratigraphic, biostratigraphic and chemostratigraphic indicators as seen in several Permian-Triassic boundary locations worldwide. In this work, we re-examine some of the structural data previously presented by Gorter (1996) using some additional seismic lines. We have also evaluated several impact tracers including iridium, shocked quartz, productivity collapse, helium-3, chromium-53 and fullerenes with trapped noble gases from some Permian-Triassic boundary sites in the Tethys and Circum-Pacific regions. Our findings suggest that the Bedout structure is a good candidate for an oceanic impact at the end Permian, triggering the most severe mass extinction in the history of life on Earth.

Effect of multi-layer thermal insulation thickness and location on the hypervelocity impact response of dual-wall structures

NASA Astrophysics Data System (ADS)

Schonberg, William P.

Traditional perforation-resistant wall design for long-duration spacecraft consists of a "bumper" that is placed a small distance away from the main "pressure wall" of a spacecraft compartment or module. This concept has been studied extensively as a means of reducing the perforation threat of hypervelocity projectiles such as meteoroids and orbital debris. If a dual-wall system is employed on an earth-orbiting spacecraft, then a blanket of multi-layer insulation (MLI) will typically be included within the dual-wall system for thermal protection purposes. This paper presents the results of an experimental study in which aluminum dual-wall structures were tested under a variety of high-speed impact conditions to study the effect of MLI thickness and location on perforation resistance. The results presented consist of test-by-test comparisons of the damage sustained by similar dual-wall systems with blanket MLI of various thicknesses and at various locations within the dual-wall systems under similar impact loading conditions. The analyses performed revealed that the placement of the MLI had a significant effect on the ballistic limit of the dual-wall structures considered while reducing the thickness of the MLI by as much as 1/3 did not.

Transient loads identification for a standoff metallic thermal protection system panel.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hundhausen, R. J.; Adams, Douglas E.; Derriso, Mark

2004-01-01

Standoff thermal protection system (TPS) panels are critical structural components in future aerospace vehicles because they protect the vehicle from the hostile environment encountered during space launch and reentry. Consequently, the panels are exposed to a variety of loads including high temperature thermal stresses, thermal shock, acoustic pressure, and foreign object impacts. Transient impacts are especially detrimental because they can cause immediate and severe degradation of the panel in the form of, for example, debonding and buckling of the face sheet, cracking of the fasteners, or deformation of the standoffs. Loads identification methods for determining the magnitude and location ofmore » impact loads provide an indication of TPS components that may be more susceptible to failure. Furthermore, a historical database of impact loads encountered can be retained for use in the development of statistical models that relate impact loading to panel life. In this work, simulated inservice transient loads are identified experimentally using two methods: a physics-based approach and an inverse Frequency Response Function (FRF) approach. It is shown that by applying the inverse FRF method, the location and magnitude of these simulated impacts can be identified with a high degree of accuracy. The identified force levels vary significantly with impact location due to the differences in panel deformation at the impact site indicating that resultant damage due to impacts would vary with location as well.« less

Impact localization on composite structures using time difference and MUSIC approach

NASA Astrophysics Data System (ADS)

Zhong, Yongteng; Xiang, Jiawei

2017-05-01

1-D uniform linear array (ULA) has the shortcoming of the half-plane mirror effect, which does not allow discriminating between a target placed above the array and a target placed below the array. This paper presents time difference (TD) and multiple signal classification (MUSIC) based omni-directional impact localization on a large stiffened composite structure using improved linear array, which is able to perform omni-directional 360° localization. This array contains 2M+3 PZT sensors, where 2M+1 PZT sensors are arranged as a uniform linear array, and the other two PZT sensors are placed above and below the array. Firstly, the arrival times of impact signals observed by the other two sensors are determined using the wavelet transform. Compared with each other, the direction range of impact source can be decided in general, 0°to 180° or 180°to 360°. And then, two dimensional multiple signal classification (2D-MUSIC) based spatial spectrum formula using the uniform linear array is applied for impact localization by the general direction range. When the arrival times of impact signals observed by upper PZT is equal to that of lower PZT, the direction can be located in x axis (0°or 180°). And time difference based MUSIC method is present to locate impact position. To verify the proposed approach, the proposed approach is applied to a composite structure. The localization results are in good agreement with the actual impact occurring positions.

Classification of Low Velocity Impactors Using Spiral Sensing of Acousto-Ultrasonic Waves

NASA Astrophysics Data System (ADS)

Agbasi, Chijioke Raphael

The non-linear elastodynamics of a flat plate subjected to low velocity foreign body impacts is studied, resembling the space debris impacts on the space structure. The work is based on a central hypothesis that in addition to identifying the impact locations, the material properties of the foreign objects can also be classified using acousto-ultrasonic signals (AUS). Simultaneous localization of impact point and classification of impact object is quite challenging using existing state-of-the-art structural health monitoring (SHM) approaches. Available techniques seek to report the exact location of impact on the structure, however, the reported information is likely to have errors from nonlinearity and variability in the AUS signals due to materials, geometry, boundary conditions, wave dispersion, environmental conditions, sensor and hardware calibration etc. It is found that the frequency and speed of the guided wave generated in the plate can be quantized based on the impactor's relationship with the plate (i.e. the wave speed and the impactor's mechanical properties are coupled). In this work, in order to characterize the impact location and mechanical properties of imapctors, nonlinear transient phenomenon is empirically studied to decouple the understanding using the dominant frequency band (DFB) and Lag Index (LI) of the acousto-ultrasonic signals. Next the understanding was correlated with the elastic modulus of the impactor to predict transmitted force histories. The proposed method presented in this thesis is especially applicable for SHM where sensors cannot be widely or randomly distributed. Thus a strategic organization and localization of the sensors is achieved by implementing the geometric configuration of Theodorous Spiral Sensor Cluster (TSSC). The performance of TSSC in characterizing the impactor types are compared with other conventional sensor clusters (e.g. square, circular, random etc.) and it is shown that the TSSC is advantageous over conventional localized sensor clusters. It was found that the TSSC provides unbiased sensor voting that boosts sensitivity towards classification of impact events. To prove the concept, a coupled field (multiphysics) finite element model (CFFEM) is developed and a series of experiments were performed. The dominant frequency band (DBF) along with a Lag Index (LI) feature extraction technique was found to be suitable for classifying the impactors. Results show that TSSC with DBF features increase the sensitivity of impactor's elastic modulus, if the covariance of the AUS from the TSSC and other conventional sensor clusters are compared. It is observe that for the impact velocity, geometric and mechanical properties studied herein, longitudinal and flexural waves are excited, and there are quantifiable differences in the Lamb wave signatures excited for different impactor materials. It is found that such differences are distinguishable only by the proposed TSSC, but not by other state-of-the-art sensor configurations used in SHM. This study will be useful for modeling an inverse problem needed for classifying impactor materials and the subsequent reconstruction of force histories via neural network or artificial intelligence. Finally an alternative novel approach is proposed to describe the Probability Map of Impact (PMOI) over the entire structure. PMOI could serve as a read-out tool for simultaneously identifying the impact location and the type of the impactor that has impacted the structure. PMOI is intended to provide high risk areas of the space structures where the incipient damage could exist (e.g. area with PMOI > 95%) after an impact.

Impact gages for detecting meteoroid and other orbital debris impacts on space vehicles.

NASA Technical Reports Server (NTRS)

Mastandrea, J. R.; Scherb, M. V.

1973-01-01

Impacts on space vehicles have been simulated using the McDonnell Douglas Aerophysics Laboratory (MDAL) Light-Gas Guns to launch particles at hypervelocity speeds into scaled space structures. Using impact gages and a triangulation technique, these impacts have been detected and accurately located. This paper describes in detail the various types of impact gages (piezoelectric PZT-5A, quartz, electret, and off-the-shelf plastics) used. This description includes gage design and experimental results for gages installed on single-walled scaled payload carriers, multiple-walled satellites and space stations, and single-walled full-scale Delta tank structures. A brief description of the triangulation technique, the impact simulation, and the data acquisition system are also included.

Analysis of simple sequence repeat (SSR) structure and sequence within Epichloë endophyte genomes reveals impacts on gene structure and insights into ancestral hybridization events.

PubMed

Clayton, William; Eaton, Carla Jane; Dupont, Pierre-Yves; Gillanders, Tim; Cameron, Nick; Saikia, Sanjay; Scott, Barry

2017-01-01

Epichloë grass endophytes comprise a group of filamentous fungi of both sexual and asexual species. Known for the beneficial characteristics they endow upon their grass hosts, the identification of these endophyte species has been of great interest agronomically and scientifically. The use of simple sequence repeat loci and the variation in repeat elements has been used to rapidly identify endophyte species and strains, however, little is known of how the structure of repeat elements changes between species and strains, and where these repeat elements are located in the fungal genome. We report on an in-depth analysis of the structure and genomic location of the simple sequence repeat locus B10, commonly used for Epichloë endophyte species identification. The B10 repeat was found to be located within an exon of a putative bZIP transcription factor, suggesting possible impacts on polypeptide sequence and thus protein function. Analysis of this repeat in the asexual endophyte hybrid Epichloë uncinata revealed that the structure of B10 alleles reflects the ancestral species that hybridized to give rise to this species. Understanding the structure and sequence of these simple sequence repeats provides a useful set of tools for readily distinguishing strains and for gaining insights into the ancestral species that have undergone hybridization events.

Calling in sick: impacts of fever on intra-urban human mobility.

PubMed

Perkins, T Alex; Paz-Soldan, Valerie A; Stoddard, Steven T; Morrison, Amy C; Forshey, Brett M; Long, Kanya C; Halsey, Eric S; Kochel, Tadeusz J; Elder, John P; Kitron, Uriel; Scott, Thomas W; Vazquez-Prokopec, Gonzalo M

2016-07-13

Pathogens inflict a wide variety of disease manifestations on their hosts, yet the impacts of disease on the behaviour of infected hosts are rarely studied empirically and are seldom accounted for in mathematical models of transmission dynamics. We explored the potential impacts of one of the most common disease manifestations, fever, on a key determinant of pathogen transmission, host mobility, in residents of the Amazonian city of Iquitos, Peru. We did so by comparing two groups of febrile individuals (dengue-positive and dengue-negative) with an afebrile control group. A retrospective, semi-structured interview allowed us to quantify multiple aspects of mobility during the two-week period preceding each interview. We fitted nested models of each aspect of mobility to data from interviews and compared models using likelihood ratio tests to determine whether there were statistically distinguishable differences in mobility attributable to fever or its aetiology. Compared with afebrile individuals, febrile study participants spent more time at home, visited fewer locations, and, in some cases, visited locations closer to home and spent less time at certain types of locations. These multifaceted impacts are consistent with the possibility that disease-mediated changes in host mobility generate dynamic and complex changes in host contact network structure. © 2016 The Author(s).

Calling in sick: impacts of fever on intra-urban human mobility

PubMed Central

Perkins, T. Alex; Paz-Soldan, Valerie A.; Stoddard, Steven T.; Morrison, Amy C.; Forshey, Brett M.; Long, Kanya C.; Halsey, Eric S.; Kochel, Tadeusz J.; Elder, John P.; Kitron, Uriel; Scott, Thomas W.; Vazquez-Prokopec, Gonzalo M.

2016-01-01

Pathogens inflict a wide variety of disease manifestations on their hosts, yet the impacts of disease on the behaviour of infected hosts are rarely studied empirically and are seldom accounted for in mathematical models of transmission dynamics. We explored the potential impacts of one of the most common disease manifestations, fever, on a key determinant of pathogen transmission, host mobility, in residents of the Amazonian city of Iquitos, Peru. We did so by comparing two groups of febrile individuals (dengue-positive and dengue-negative) with an afebrile control group. A retrospective, semi-structured interview allowed us to quantify multiple aspects of mobility during the two-week period preceding each interview. We fitted nested models of each aspect of mobility to data from interviews and compared models using likelihood ratio tests to determine whether there were statistically distinguishable differences in mobility attributable to fever or its aetiology. Compared with afebrile individuals, febrile study participants spent more time at home, visited fewer locations, and, in some cases, visited locations closer to home and spent less time at certain types of locations. These multifaceted impacts are consistent with the possibility that disease-mediated changes in host mobility generate dynamic and complex changes in host contact network structure. PMID:27412286

Semi-Automated Air-Coupled Impact-Echo Method for Large-Scale Parkade Structure.

PubMed

Epp, Tyler; Svecova, Dagmar; Cha, Young-Jin

2018-03-29

Structural Health Monitoring (SHM) has moved to data-dense systems, utilizing numerous sensor types to monitor infrastructure, such as bridges and dams, more regularly. One of the issues faced in this endeavour is the scale of the inspected structures and the time it takes to carry out testing. Installing automated systems that can provide measurements in a timely manner is one way of overcoming these obstacles. This study proposes an Artificial Neural Network (ANN) application that determines intact and damaged locations from a small training sample of impact-echo data, using air-coupled microphones from a reinforced concrete beam in lab conditions and data collected from a field experiment in a parking garage. The impact-echo testing in the field is carried out in a semi-autonomous manner to expedite the front end of the in situ damage detection testing. The use of an ANN removes the need for a user-defined cutoff value for the classification of intact and damaged locations when a least-square distance approach is used. It is postulated that this may contribute significantly to testing time reduction when monitoring large-scale civil Reinforced Concrete (RC) structures.

Semi-Automated Air-Coupled Impact-Echo Method for Large-Scale Parkade Structure

PubMed Central

Epp, Tyler; Svecova, Dagmar; Cha, Young-Jin

2018-01-01

Structural Health Monitoring (SHM) has moved to data-dense systems, utilizing numerous sensor types to monitor infrastructure, such as bridges and dams, more regularly. One of the issues faced in this endeavour is the scale of the inspected structures and the time it takes to carry out testing. Installing automated systems that can provide measurements in a timely manner is one way of overcoming these obstacles. This study proposes an Artificial Neural Network (ANN) application that determines intact and damaged locations from a small training sample of impact-echo data, using air-coupled microphones from a reinforced concrete beam in lab conditions and data collected from a field experiment in a parking garage. The impact-echo testing in the field is carried out in a semi-autonomous manner to expedite the front end of the in situ damage detection testing. The use of an ANN removes the need for a user-defined cutoff value for the classification of intact and damaged locations when a least-square distance approach is used. It is postulated that this may contribute significantly to testing time reduction when monitoring large-scale civil Reinforced Concrete (RC) structures. PMID:29596332

Analysis on Voltage Profile of Distribution Network with Distributed Generation

NASA Astrophysics Data System (ADS)

Shao, Hua; Shi, Yujie; Yuan, Jianpu; An, Jiakun; Yang, Jianhua

2018-02-01

Penetration of distributed generation has some impacts on a distribution network in load flow, voltage profile, reliability, power loss and so on. After the impacts and the typical structures of the grid-connected distributed generation are analyzed, the back/forward sweep method of the load flow calculation of the distribution network is modelled including distributed generation. The voltage profiles of the distribution network affected by the installation location and the capacity of distributed generation are thoroughly investigated and simulated. The impacts on the voltage profiles are summarized and some suggestions to the installation location and the capacity of distributed generation are given correspondingly.

Modeling climate change impacts on combined sewer overflow using synthetic precipitation time series.

PubMed

Bendel, David; Beck, Ferdinand; Dittmer, Ulrich

2013-01-01

In the presented study climate change impacts on combined sewer overflows (CSOs) in Baden-Wuerttemberg, Southern Germany, were assessed based on continuous long-term rainfall-runoff simulations. As input data, synthetic rainfall time series were used. The applied precipitation generator NiedSim-Klima accounts for climate change effects on precipitation patterns. Time series for the past (1961-1990) and future (2041-2050) were generated for various locations. Comparing the simulated CSO activity of both periods we observe significantly higher overflow frequencies for the future. Changes in overflow volume and overflow duration depend on the type of overflow structure. Both values will increase at simple CSO structures that merely divide the flow, whereas they will decrease when the CSO structure is combined with a storage tank. However, there is a wide variation between the results of different precipitation time series (representative for different locations).

Availability: A Metric for Nucleic Acid Strand Displacement Systems.

PubMed

Olson, Xiaoping; Kotani, Shohei; Padilla, Jennifer E; Hallstrom, Natalya; Goltry, Sara; Lee, Jeunghoon; Yurke, Bernard; Hughes, William L; Graugnard, Elton

2017-01-20

DNA strand displacement systems have transformative potential in synthetic biology. While powerful examples have been reported in DNA nanotechnology, such systems are plagued by leakage, which limits network stability, sensitivity, and scalability. An approach to mitigate leakage in DNA nanotechnology, which is applicable to synthetic biology, is to introduce mismatches to complementary fuel sequences at key locations. However, this method overlooks nuances in the secondary structure of the fuel and substrate that impact the leakage reaction kinetics in strand displacement systems. In an effort to quantify the impact of secondary structure on leakage, we introduce the concepts of availability and mutual availability and demonstrate their utility for network analysis. Our approach exposes vulnerable locations on the substrate and quantifies the secondary structure of fuel strands. Using these concepts, a 4-fold reduction in leakage has been achieved. The result is a rational design process that efficiently suppresses leakage and provides new insight into dynamic nucleic acid networks.

Damage Detection Sensor System for Aerospace and Multiple Applications

NASA Technical Reports Server (NTRS)

Williams, M.; Lewis, M.; Gibson, T.; Medelius, P.; Lane, J.

2017-01-01

The damage detection sensory system is an intelligent damage detection ‘skin’ that can be embedded into rigid or flexible structures, providing a lightweight capability for in-situ health monitoring for applications such as spacecraft, expandable or inflatable structures, extravehicular activities (EVA) suits, smart wearables, and other applications where diagnostic impact damage monitoring might be critical. The sensor systems can be customized for detecting location, damage size, and depth, with velocity options and can be designed for particular environments for monitoring of impact or physical damage to a structure. The operation of the sensor detection system is currently based on the use of parallel conductive traces placed on a firm or flexible surface. Several detection layers can be implemented, where alternate layers are arranged in orthogonal direction with respect to the adjacent layers allowing for location and depth calculations. Increased flexibility of the damage detection sensor system designs will also be introduced.

Earth Observations taken by Expedition 34 crewmember

NASA Image and Video Library

2013-01-15

ISS034-E-029105 (15 Jan. 2013) --- One of the Expedition 34 crew members aboard the Earth-orbiting International Space Station photographed this image of the Piccaninny impact structure, located within the semi-arid Purnululu National Park and World Heritage site in Australia. The structure is believed by most scientists to have been formed less than 360 million years ago. Specifically, the 7.5 kilometer diameter structure forms a roughly circular plateau within the striking sandstone cone towers of the Bungle Bungle Range. Geological evidence indicating an impact structure includes regional folding and faulting patterns both within and surrounding the plateau. Features confirming an impact, such as shock textures (indicating rapid compression, melting, and fracturing during impact) in rocks and minerals have not yet been found; this, according to scientists, is perhaps due to removal during erosion of an original crater.

Flynn Creek Impact Structure: New Insights from Breccias, Melt Features, Shatter Cones, and Remote Sensing

NASA Technical Reports Server (NTRS)

Evenick, J. C.; Lee, P.; Deane, B.

2004-01-01

The Flynn Creek impact structure is located in Tennessee, USA (36 deg.17 min.N, 85 deg.40 min.W). The structure was first mapped as a crypto-volcanic by Wilson and Born in 1936 [1]. Although they did not properly identify the stratigraphy within the crater or the causal mechanism, they did correctly define the horizontal extent of the crater. More detailed surface and subsurface research by Roddy (1979) accurately described the crater as being an impact structure with a diameter of 3.8 km. It formed around 360 Ma, which corresponds to the interval between the deposition of the Nashville Group and the Chattanooga Shale. Although there is limited rock outcrop in the area, there are exposed surface faults, folds, and large outcrops of impact breccia within the crater.

Popigai Impact Structure Modeling: Morphology and Worldwide Ejecta

NASA Technical Reports Server (NTRS)

Ivanov, B. A.; Artemieva, N. A.; Pierazzo, E.

2004-01-01

The approx. 100 km in diameter, 35.7 0.2 Ma old Popigai structure [1], northern Siberia (Russia), is the best-preserved of the large terrestrial complex crater structures containing a central-peak ring [2- 4]. Although remotely located, the excellent outcrops, large number of drill cores, and wealth of geochemical data make Popigai ideal for the general study of the cratering processes. It is most famous for its impact-diamonds [2,5]. Popigai is the best candidate for the source crater of the worldwide late Eocene ejecta [6,7].

Structural health monitoring of inflatable structures for MMOD impacts

NASA Astrophysics Data System (ADS)

Anees, Muhammad; Gbaguidi, Audrey; Kim, Daewon; Namilae, Sirish

2017-04-01

Inflatable structures for space habitat are highly prone to damage caused by micrometeoroid and orbital debris impacts. Although the structures are effectively shielded against these impacts through multiple layers of impact resistant materials, there is a necessity for a health monitoring system to monitor the structural integrity and damage state within the structures. Assessment of damage is critical for the safety of personnel in the space habitat, as well as predicting the repair needs and the remaining useful life of the habitat. In this paper, we propose a unique impact detection and health monitoring system based on hybrid nanocomposite sensors. The sensors are composed of two fillers, carbon nanotubes and coarse graphene platelets with an epoxy matrix material. The electrical conductivity of these flexible nanocomposite sensors is highly sensitive to strains as well as presence of any holes and damage in the structure. The sensitivity of the sensors to the presence of 3mm holes due to an event of impact is evaluated using four point probe electrical resistivity measurements. An array of these sensors when sandwiched between soft good layers in a space habitat can act as a damage detection layer for inflatable structures. An algorithm is developed to determine the event of impact, its severity and location on the sensing layer for active health monitoring.

Adverse event detection (AED) system for continuously monitoring and evaluating structural health status

NASA Astrophysics Data System (ADS)

Yun, Jinsik; Ha, Dong Sam; Inman, Daniel J.; Owen, Robert B.

2011-03-01

Structural damage for spacecraft is mainly due to impacts such as collision of meteorites or space debris. We present a structural health monitoring (SHM) system for space applications, named Adverse Event Detection (AED), which integrates an acoustic sensor, an impedance-based SHM system, and a Lamb wave SHM system. With these three health-monitoring methods in place, we can determine the presence, location, and severity of damage. An acoustic sensor continuously monitors acoustic events, while the impedance-based and Lamb wave SHM systems are in sleep mode. If an acoustic sensor detects an impact, it activates the impedance-based SHM. The impedance-based system determines if the impact incurred damage. When damage is detected, it activates the Lamb wave SHM system to determine the severity and location of the damage. Further, since an acoustic sensor dissipates much less power than the two SHM systems and the two systems are activated only when there is an acoustic event, our system reduces overall power dissipation significantly. Our prototype system demonstrates the feasibility of the proposed concept.

Dynamic Social Impact: The Creation of Culture by Communication.

ERIC Educational Resources Information Center

Latane, Bibb

1996-01-01

Presents a theory of how individuals located in social space influence each other to create higher order patterns of cultural structure. Presents the theory as five propositions and six derivations, arguing that Dynamic Social Impact Theory accounts for four key features of culture: regional clustering, correlations among cultural elements,…

Gravimetric 3D Subsurface Modelling of the Cerro Do Jarau Structure, Rio Grande Do Sul, Brazil.

NASA Astrophysics Data System (ADS)

Giacomini, B. B.

2014-12-01

Although common in other bodies of the solar system, impact craters formed in basaltic terrains are rare on Earth and only a few examples are known. Two of these craters are located south of Brazil, the Vargeão and Vista Alegre impact craters. The Cerro do Jarau structure is not confirmed, but is a possible third Brazilian basaltic crater, formed above the Serra Geral basalt floods of the Paraná Basin like the other two. Cerro do Jarau is a 13 km circular landform that rises over 200 meters above the plains of the "pampas" in southern Brazil. The name, meaning "Jarau hills", is given after the crests of silicified and deformed Botucatu sandstones, which form a semiring of elevated hills in the northern part of the structure. This work focused on the construction of a 3D subsurface geological model that could explain a new set of ground gravimetric data. Bouguer anomalies were calculated from gravity acceleration measured at 313 stations irregularly distributed on the area of the impact structure. A regional component represented by a polynomial trend surface was extracted from the total Bouguer anomalies. The residual Bouguer map (fig. 1) shows a strong positive anomaly with a NE-SW trend, located in the northeastern part of the structure. This gravity feature is not common in other impact structures, being possibly related to a dike intrusion. However, the negative anomaly present in the center of the structure and the circular positive anomaly surrounding the central part of the structure could be related to an impact structure. The positive circular anomaly is not spatially coincident with the edges of the structure, a feature that is also observed at the Vargeão and Vista Alegre impact structures. Density values of basalts, sandstones and breccias were measured from rock samples and each average value were used as constraints for the 3D model developed with the Geosoft® VOXI Earth modelling.This model provided a better understanding of the subsurface design of the structure. The impact crater hypothesis still remain the best hypothesis, but our results suggest that there was a post-impact dike intrusion and deep erosion processes that removed most of the impact breccia and a possible central uplift. The remaining of the uplifted rocks is observed as the silicified sandstone that forms the crests of the Jarau hills.

Numerical simulation and experimental validation of Lamb wave propagation behavior in composite plates

NASA Astrophysics Data System (ADS)

Kim, Sungwon; Uprety, Bibhisha; Mathews, V. John; Adams, Daniel O.

2015-03-01

Structural Health Monitoring (SHM) based on Acoustic Emission (AE) is dependent on both the sensors to detect an impact event as well as an algorithm to determine the impact location. The propagation of Lamb waves produced by an impact event in thin composite structures is affected by several unique aspects including material anisotropy, ply orientations, and geometric discontinuities within the structure. The development of accurate numerical models of Lamb wave propagation has important benefits towards the development of AE-based SHM systems for impact location estimation. Currently, many impact location algorithms utilize the time of arrival or velocities of Lamb waves. Therefore the numerical prediction of characteristic wave velocities is of great interest. Additionally, the propagation of the initial symmetric (S0) and asymmetric (A0) wave modes is important, as these wave modes are used for time of arrival estimation. In this investigation, finite element analyses were performed to investigate aspects of Lamb wave propagation in composite plates with active signal excitation. A comparative evaluation of two three-dimensional modeling approaches was performed, with emphasis placed on the propagation and velocity of both the S0 and A0 wave modes. Results from numerical simulations are compared to experimental results obtained from active AE testing. Of particular interest is the directional dependence of Lamb waves in quasi-isotropic carbon/epoxy composite plates. Numerical and experimental results suggest that although a quasi-isotropic composite plate may have the same effective elastic modulus in all in-plane directions, the Lamb wave velocity may have some directional dependence. Further numerical analyses were performed to investigate Lamb wave propagation associated with circular cutouts in composite plates.

Impact effects and regional tectonic insights: Backstripping the Chesapeake Bay impact structure

USGS Publications Warehouse

Hayden, T.; Kominz, M.; Powars, D.S.; Edwards, L.E.; Miller, K.G.; Browning, J.V.; Kulpecz, A.A.

2008-01-01

The Chesapeake Bay impact structure is a ca. 35.4 Ma crater located on the eastern seaboard of North America. Deposition returned to normal shortly after impact, resulting in a unique record of both impact-related and subsequent passive margin sedimentation. We use backstripping to show that the impact strongly affected sedimentation for 7 m.y. through impact-derived crustal-scale tectonics, dominated by the effects of sediment compaction and the introduction and subsequent removal of a negative thermal anomaly instead of the expected positive thermal anomaly. After this, the area was dominated by passive margin thermal subsidence overprinted by periods of regional-scale vertical tectonic events, on the order of tens of meters. Loading due to prograding sediment bodies may have generated these events. ?? 2008 The Geological Society of America.

Acoustic emission monitoring of low velocity impact damage in graphite/epoxy laminates during tensile loading

NASA Technical Reports Server (NTRS)

Parker, Bradford H.

1992-01-01

An acoustic emission (AE) system was set up in a linear location data acquisition mode to monitor the tensile loading of eight-ply quasi-isotropic graphite/epoxy specimens containing low velocity impact damage. The impact damage was induced using an instrumented drop weight tower. During impact, specimens were supported by either an aluminum plate or a membrane configuration. Cross-sectional examinations revealed that the aluminum plate configuration resulted in primarily matrix cracking and back surface fiber failure. The membrane support resulted in only matrix cracking and delamination damage. Penetrant enhanced radiography and immersion ultrasonics were used in order to assess the amount of impact damage in each tensile specimen. During tensile loading, AE reliably detected and located the damage sites which included fiber failure. All specimens with areas of fiber breakage ultimately failed at the impact site. AE did not reliably locate damage which consisted of only delaminations and matrix cracking. Specimens with this type of damage did not ultimately fail at the impact site. In summary, AE demonstrated the ability to increase the reliability of structural proof tests; however, the successful use of this technique requires extensive baseline testing.

CALL-FOR-ABSTRACTS: SYMPOSIUM ON TECHNOLOGIES FOR PROTECTING AQUATIC ORGANISMS FROM COOLING WATER INTAKE STRUCTURES

EPA Science Inventory

Section 316(b) of the Clean Water Act requires EPA to ensure that the location, design, construction, and capacity of cooling water intake structures reflect the best technology available for minimizing adverse environmental impacts. In February 2002, the EPA approved a proposed ...

Breccia Formation at a Complex Impact Crater: Slate Islands, Lake Superior, Ontario, Canada

NASA Technical Reports Server (NTRS)

Dressler, B. O.; Sharpton, V. L.

1997-01-01

The Slate Islands impact structure is the eroded remnant of a approximately 30-32 km-diameter complex impact structure located in northern Lake Superior, Ontario, Canada. Target rocks are Archean supracrustal and igneous rocks and Proterozoic metavolcanics, metasediments, and diabase. A wide variety of breccias occurs on the islands, many of which contain fragments exhibiting shock metamorphic features. Aphanitic, narrow and inclusion-poor pseudotachylite veins, commonly with more or less parallel boundaries and apophyses branching off them, represent the earliest breccias formed during the compression stage of the impact process. Coarse-grained, polymictic elastic matrix breccias form small to very large, inclusion-rich dikes and irregularly shaped bodies that may contain altered glass fragments. These breccias have sharp contacts with their host rocks and include a wide range of fragment types some of which were transported over minimum distances of approximately 2 km away from the center of the structure. They cut across pseudotachylite veins and contain inclusions of them. Field and petrographic evidence indicate that these polymictic breccias formed predominantly during the excavation and central uplift stages of the impact process. Monomictic breccias, characterized by angular fragments and transitional contacts with their host rocks, occur in parautochthonous target rocks, mainly on the outlying islands of the Slate Islands archipelago. A few contain fragmented and disrupted, coarse-grained, polymictic clastic matrix breccia dikes. This is an indication that at least some of these monomictic breccias formed late in the impact process and that they are probably related to a late crater modification stage. A small number of relatively large occurrences of glass-poor, suevitic breccias occur at the flanks of the central uplift and along the inner flank of the outer ring of the Slate Islands complex crater. A coarse, glass-free, allogenic breccia, containing shatter-coned fragments derived from Proterozoic target rocks (upper target strata), observed at two locations may be analogous to the 'Bunt Breccia' of the Ries crater in Germany. At one of these locations this breccia lies close to a crater suevite deposit. At the other, it overlies parautochthonous, monomictic breccia. The State Islands impact breccias are superbly exposed, much better than breccias in most other terrestrial impact structures. Observations, including those indicative of multiple and and sequential processes, provide insight on how impact breccias form and how they relate to the various phases of the impact process. Eventually they will lead to an improved understanding of planetary impact processes.

A hydrothermal system associated with the Siljan impact structure, Sweden--implications for the search for fossil life on Mars.

PubMed

Hode, Tomas; von Dalwigk, Ilka; Broman, Curt

2003-01-01

The Siljan ring structure (368 +/- 1.1 Ma) is the largest known impact structure in Europe. It isa 65-km-wide, eroded, complex impact structure, displaying several structural units, including a central uplifted region surrounded by a ring-shaped depression. Associated with the impact crater are traces of a post-impact hydrothermal system indicated by precipitated and altered hydrothermal mineral assemblages. Precipitated hydrothermal minerals include quartz veins and breccia fillings associated with granitic rocks at the outer margin of the central uplift, and calcite, fluorite, galena, and sphalerite veins associated with Paleozoic carbonate rocks located outside the central uplift. Two-phase water/gas and oil/gas inclusions in calcite and fluorite display homogenization temperatures between 75 degrees C and 137 degrees C. With an estimated erosional unloading of approximately 1 km, the formation temperatures were probably not more than 10-15 degrees C higher. Fluid inclusion ice-melting temperatures indicate a very low salt content, reducing the probability that the mineralization was precipitated during the Caledonian Orogeny. Our findings suggest that large impacts induce low-temperature hydrothermal systems that may be habitats for thermophilic organisms. Large impact structures on Mars may therefore be suitable targets in the search for fossil thermophilic organisms.

Real-Time Impact Visualization Inspection of Aerospace Composite Structures with Distributed Sensors.

PubMed

Si, Liang; Baier, Horst

2015-07-08

For the future design of smart aerospace structures, the development and application of a reliable, real-time and automatic monitoring and diagnostic technique is essential. Thus, with distributed sensor networks, a real-time automatic structural health monitoring (SHM) technique is designed and investigated to monitor and predict the locations and force magnitudes of unforeseen foreign impacts on composite structures and to estimate in real time mode the structural state when impacts occur. The proposed smart impact visualization inspection (IVI) technique mainly consists of five functional modules, which are the signal data preprocessing (SDP), the forward model generator (FMG), the impact positioning calculator (IPC), the inverse model operator (IMO) and structural state estimator (SSE). With regard to the verification of the practicality of the proposed IVI technique, various structure configurations are considered, which are a normal CFRP panel and another CFRP panel with "orange peel" surfaces and a cutout hole. Additionally, since robustness against several background disturbances is also an essential criterion for practical engineering demands, investigations and experimental tests are carried out under random vibration interfering noise (RVIN) conditions. The accuracy of the predictions for unknown impact events on composite structures using the IVI technique is validated under various structure configurations and under changing environmental conditions. The evaluated errors all fall well within a satisfactory limit range. Furthermore, it is concluded that the IVI technique is applicable for impact monitoring, diagnosis and assessment of aerospace composite structures in complex practical engineering environments.

Real-Time Impact Visualization Inspection of Aerospace Composite Structures with Distributed Sensors

PubMed Central

Si, Liang; Baier, Horst

2015-01-01

For the future design of smart aerospace structures, the development and application of a reliable, real-time and automatic monitoring and diagnostic technique is essential. Thus, with distributed sensor networks, a real-time automatic structural health monitoring (SHM) technique is designed and investigated to monitor and predict the locations and force magnitudes of unforeseen foreign impacts on composite structures and to estimate in real time mode the structural state when impacts occur. The proposed smart impact visualization inspection (IVI) technique mainly consists of five functional modules, which are the signal data preprocessing (SDP), the forward model generator (FMG), the impact positioning calculator (IPC), the inverse model operator (IMO) and structural state estimator (SSE). With regard to the verification of the practicality of the proposed IVI technique, various structure configurations are considered, which are a normal CFRP panel and another CFRP panel with “orange peel” surfaces and a cutout hole. Additionally, since robustness against several background disturbances is also an essential criterion for practical engineering demands, investigations and experimental tests are carried out under random vibration interfering noise (RVIN) conditions. The accuracy of the predictions for unknown impact events on composite structures using the IVI technique is validated under various structure configurations and under changing environmental conditions. The evaluated errors all fall well within a satisfactory limit range. Furthermore, it is concluded that the IVI technique is applicable for impact monitoring, diagnosis and assessment of aerospace composite structures in complex practical engineering environments. PMID:26184196

Rapid Bioassessment Methods for Assessing Stream Macroinvertebrate Community on the Savannah River Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Specht, W.L.

Macroinvertebrate sampling was performed at 16 locations in the Savannah River Site (SRS) streams using Hester-Dendy multiplate samplers and EPA Rapid Bioassessment Protocols (RBP). Some of the sampling locations were unimpacted, while other locations had been subject to various forms of perturbation by SRS activities. In general, the data from the Hester-Dendy multiplate samplers were more sensitive at detecting impacts than were the RBP data. We developed a Biotic Index for the Hester-Dendy data which incorporated eight community structure, function, and balance parameters. when tested using a data set that was unrelated to the data set that was used inmore » developing the Biotic Index, the index was very successful at detecting impact.« less

New perspectives on the Popigai impact structure

NASA Technical Reports Server (NTRS)

Garvin, J. B.; Deino, A. L.

1992-01-01

The record of large-scale cratering on Earth is scant, and the only currently 'proven' 100-km-class impact structure known to have formed within the Cenozoic is Popigai, located in the Siberian Arctic at 71.5 deg N, 111 deg E. Popigai is clearly a multiringed impact basin formed within the crystalline shield rocks (Anabar) and platform sediments of the Siberian taiga, and estimates of the volume of preserved impact melt typically exceed 1700 cu km, which is within a factor of 2-3 of what would be predicted using scaling relationships. We present the preliminary results of an analysis of the present-day topography of the Popigai structure, together with refined absolute age estimates, in order to reconstruct the pre-erosional morphology of the basin, as well as to quantify the erosion or sediment infill rates in the Popigai region.

Lac Télé structure, Republic of Congo: Geological setting of a cryptozoological and biodiversity hotspot, and evidence against an impact origin

NASA Astrophysics Data System (ADS)

Master, Sharad

2010-11-01

Lac Télé is a large lake, ˜5.6 km in diameter, with an ovoid shape, situated at 17°10'E, 1°20'N, in the great tropical rain forest region of the Republic of Congo. This lake has attracted widespread attention, mainly because of the legends among the local people that it harbours a strange animal known as the Mokele-Mbembe, but also because it is situated in a region that is a hotbed of biodiversity and conservation efforts with respect to various endangered mammalian species, including gorillas and chimpanzees. Because of its appearance, Lac Télé has been regarded as a possible meteorite impact structure. Various expeditions, studying cryptozoology, conservation ecology, biodiversity, and the impact hypothesis, have visited Lac Télé in the past several decades. The Lac Télé structure is located in the NW part of the intracratonic Congo Basin, in a region dominated by Holocene alluvium, dense tropical rain forest, and swamps which form part of the basin of the Likouala aux Herbes, a multi-branched meandering river flowing over very low gradients into the Sangha river, a major tributary of the Congo river. Previous bathymetric studies have shown that the average depth of Lac Télé is only 4 m, including organic-rich silty sediments. The structure is that of a flat-bottomed dish. Modelling of the Lac Télé as an impact structure indicates a number of features which ought to be present. The absence of any of these features, coupled with the irregular ovoid shape, the palynological record, and the location of the structure at the intersection of major regional lineaments, is regarded as evidence against the impact hypothesis. Lac Télé as an isolated lake ecosystem is not unique in the Congo Basin, and there are several other similar small shallow isolated lakes surrounded by rain forest and marshes, some of which formed by damming of drainage systems by neotectonic faults. It is suggested that the formation of Lac Télé may be related to its location over neotectonically reactivated regional lineaments, which are also seismically active. Lac Télé and other similar hydrologic systems may be biodiversity hotspots because they acted as refugia following neotectonic hydrological re-organization of the Congo Basin.

The Impact of Stereoscopic Imagery and Motion on Anatomical Structure Recognition and Visual Attention Performance

ERIC Educational Resources Information Center

Remmele, Martin; Schmidt, Elena; Lingenfelder, Melissa; Martens, Andreas

2018-01-01

Gross anatomy is located in a three-dimensional space. Visualizing aspects of structures in gross anatomy education should aim to provide information that best resembles their original spatial proportions. Stereoscopic three-dimensional imagery might offer possibilities to implement this aim, though some research has revealed potential impairments…

Physiological and structural differences in spatially distinct subpopulations of cardiac mitochondria: influence of cardiac pathologies

PubMed Central

Thapa, Dharendra; Shepherd, Danielle L.

2014-01-01

Cardiac tissue contains discrete pools of mitochondria that are characterized by their subcellular spatial arrangement. Subsarcolemmal mitochondria (SSM) exist below the cell membrane, interfibrillar mitochondria (IFM) reside in rows between the myofibrils, and perinuclear mitochondria are situated at the nuclear poles. Microstructural imaging of heart tissue coupled with the development of differential isolation techniques designed to sequentially separate spatially distinct mitochondrial subpopulations have revealed differences in morphological features including shape, absolute size, and internal cristae arrangement. These findings have been complemented by functional studies indicating differences in biochemical parameters and, potentially, functional roles for the ATP generated, based upon subcellular location. Consequently, mitochondrial subpopulations appear to be influenced differently during cardiac pathologies including ischemia/reperfusion, heart failure, aging, exercise, and diabetes mellitus. These influences may be the result of specific structural and functional disparities between mitochondrial subpopulations such that the stress elicited by a given cardiac insult differentially impacts subcellular locales and the mitochondria contained within. The goal of this review is to highlight some of the inherent structural and functional differences that exist between spatially distinct cardiac mitochondrial subpopulations as well as provide an overview of the differential impact of various cardiac pathologies on spatially distinct mitochondrial subpopulations. As an outcome, we will instill a basis for incorporating subcellular spatial location when evaluating the impact of cardiac pathologies on the mitochondrion. Incorporation of subcellular spatial location may offer the greatest potential for delineating the influence of cardiac pathology on this critical organelle. PMID:24778166

Availability: A Metric for Nucleic Acid Strand Displacement Systems

PubMed Central

2016-01-01

DNA strand displacement systems have transformative potential in synthetic biology. While powerful examples have been reported in DNA nanotechnology, such systems are plagued by leakage, which limits network stability, sensitivity, and scalability. An approach to mitigate leakage in DNA nanotechnology, which is applicable to synthetic biology, is to introduce mismatches to complementary fuel sequences at key locations. However, this method overlooks nuances in the secondary structure of the fuel and substrate that impact the leakage reaction kinetics in strand displacement systems. In an effort to quantify the impact of secondary structure on leakage, we introduce the concepts of availability and mutual availability and demonstrate their utility for network analysis. Our approach exposes vulnerable locations on the substrate and quantifies the secondary structure of fuel strands. Using these concepts, a 4-fold reduction in leakage has been achieved. The result is a rational design process that efficiently suppresses leakage and provides new insight into dynamic nucleic acid networks. PMID:26875531

Evaluation of kinematics and injuries to restrained occupants in far-side crashes using full-scale vehicle and human body models.

PubMed

Arun, Mike W J; Umale, Sagar; Humm, John R; Yoganandan, Narayan; Hadagali, Prasanaah; Pintar, Frank A

2016-09-01

The objective of the current study was to perform a parametric study with different impact objects, impact locations, and impact speeds by analyzing occupant kinematics and injury estimations using a whole-vehicle and whole-body finite element-human body model (FE-HBM). To confirm the HBM responses, the biofidelity of the model was validated using data from postmortem human surrogate (PMHS) sled tests. The biofidelity of the model was validated using data from sled experiments and correlational analysis (CORA). Full-scale simulations were performed using a restrained Global Human Body Model Consortium (GHBMC) model seated on a 2001 Ford Taurus model using a far-side lateral impact condition. The driver seat was placed in the center position to represent a nominal initial impact condition. A 3-point seat belt with pretensioner and retractor was used to restrain the GHBMC model. A parametric study was performed using 12 simulations by varying impact locations, impacting object, and impact speed using the full-scale models. In all 12 simulations, the principal direction of force (PDOF) was selected as 90°. The impacting objects were a 10-in.-diameter rigid vertical pole and a movable deformable barrier. The impact location of the pole was at the C-pillar in the first case, at the B-pillar in the second case, and, finally, at the A-pillar in the third case. The vehicle and the GHBMC models were defined an initial velocity of 35 km/h (high speed) and 15 km/h (low speed). Excursion of the head center of gravity (CG), T6, and pelvis were measured from the simulations. In addition, injury risk estimations were performed on head, rib cage, lungs, kidneys, liver, spleen, and pelvis. The average CORA rating was 0.7. The shoulder belt slipped in B- and C-pillar impacts but somewhat engaged in the A-pillar case. In the B-pillar case, the head contacted the intruding struck-side structures, indicating higher risk of injury. Occupant kinematics depended on interaction with restraints and internal structures-especially the passenger seat. Risk analysis indicated that the head had the highest risk of sustaining an injury in the B-pillar case compared to the other 2 cases. Higher lap belt load (3.4 kN) may correspond to the Abbreviated Injury Scale (AIS) 2 pelvic injury observed in the B-pillar case. Risk of injury to other soft anatomical structures varied with impact configuration and restraint interaction. The average CORA rating was 0.7. In general, the results indicated that the high-speed impacts against the pole resulted in severe injuries, higher excursions followed by low-speed pole, high-speed moving deformable barrier (MDB), and low-speed MDB impacts. The vehicle and occupant kinematics varied with different impact setups and the latter kinematics were likely influenced by restraint effectiveness. Increased restraint engagement increased the injury risk to the corresponding anatomic structure, whereas ineffective restraint engagement increased the occupant excursion, resulting in a direct impact to the struck-side interior structures.

High Energy Wide Area Blunt Impact on Composite Aircraft Structures

NASA Astrophysics Data System (ADS)

DeFrancisci, Gabriela K.

The largest source of damage to commercial aircraft is caused by accidental contact with ground service equipment (GSE). The cylindrical bumper typically found on GSE distributes the impact load over a large contact area, possibly spanning multiple internal structural elements (frame bays) of a stiffened-skin fuselage. This type of impact can lead to damage that is widespread and difficult to detect visually. To address this problem, monolithic composite panels of various size and complexity have been modeled and tested quasi-statically and dynamically. The experimental observations have established that detectability is dependent on the impact location and immediately-adjacent internal structure of the panel, as well as the impactor geometry and total deformation of the panel. A methodology to model and predict damage caused by wide area blunt impact events was established, which was then applied to more general cases that were not tested in order to better understand the nature of this type of impact event and how it relates to the final damage state and visual detectability.

Fluid-structure interaction analysis of the drop impact test for helicopter fuel tank.

PubMed

Yang, Xianfeng; Zhang, Zhiqiang; Yang, Jialing; Sun, Yuxin

2016-01-01

The crashworthiness of helicopter fuel tank is vital to the survivability of the passengers and structures. In order to understand and improve the crashworthiness of the soft fuel tank of helicopter during the crash, this paper investigated the dynamic behavior of the nylon woven fabric composite fuel tank striking on the ground. A fluid-structure interaction finite element model of the fuel tank based on the arbitrary Lagrangian-Eulerian method was constructed to elucidate the dynamic failure behavior. The drop impact tests were conducted to validate the accuracy of the numerical simulation. Good agreement was achieved between the experimental and numerical results of the impact force with the ground. The influences of the impact velocity, the impact angle, the thickness of the fuel tank wall and the volume fraction of water on the dynamic responses of the dropped fuel tank were studied. The results indicated that the corner of the fuel tank is the most vulnerable location during the impact with ground.

Seismic velocity and crustal thickness inversions: Moon and Mars

NASA Astrophysics Data System (ADS)

Drilleau, Melanie; Blanchette-Guertin, Jean-François; Kawamura, Taichi; Lognonné, Philippe; Wieczorek, Mark

2017-04-01

We present results from new inversions of seismic data arrival times acquired by the Apollo active and passive experiments. Markov chain Monte Carlo inversions are used to constrain (i) 1-D lunar crustal and upper mantle velocity models and (ii) 3-D lateral crustal thickness models under the Apollo stations and the artificial and natural impact sites. A full 3-D model of the lunar crustal thickness is then obtained using the GRAIL gravimetric data, anchored by the crustal thicknesses under each Apollo station and impact site. To avoid the use of any seismic reference model, a Bayesian inversion technique is implemented. The advantage of such an approach is to obtain robust probability density functions of interior structure parameters governed by uncertainties on the seismic data arrival times. 1-D seismic velocities are parameterized using C1-Bézier curves, which allow the exploration of both smoothly varying models and first-order discontinuities. The parameters of the inversion include the seismic velocities of P and S waves as a function of depth, the thickness of the crust under each Apollo station and impact epicentre. The forward problem consists in a ray tracing method enabling both the relocation of the natural impact epicenters, and the computation of time corrections associated to the surface topography and the crustal thickness variations under the stations and impact sites. The results show geology-related differences between the different sites, which are due to contrasts in megaregolith thickness and to shallow subsurface composition and structure. Some of the finer structural elements might be difficult to constrain and might fall within the uncertainties of the dataset. However, we use the more precise LROC-located epicentral locations for the lunar modules and Saturn-IV upper stage artificial impacts, reducing some of the uncertainties observed in past studies. In the framework of the NASA InSight/SEIS mission to Mars, the method developed in this study will be used to constrain the Martian crustal thickness as soon as the first data will be available (late 2018). For Insight, impacts will be located by MRO data differential analysis, which provide a known location enabling the direct inversion of all differential travel times with respect to P arrival time. We have performed resolution tests to investigate to what extend impact events might help us to constrain the Martian crustal thickness. Due to the high flexibility of the Bayesian algorithm, the interior model will be refined each time a new event will be detected.

On-Orbit Assessment of Satellite Structural Properties via Robust Structural Health Monitoring

DTIC Science & Technology

2012-07-23

4-5] in aerospace applications. Compared to traditional SHM approaches using strain gages or Fiber Bragg Grating ( FBG ) sensors, the advantage of...decay model [20], principle stress directions for impact locations [21], use of Laser Doppler Vibrometer (LDV) [22] and FBG sensors [16, 23]. These...for Damage Localization in Flexural Structures Using Long-Gage FBG Sensors,” Structural Control Health Monitoring, Vol. 18, pp. 341-360, 2010. [24

Multichannel fiber laser Doppler vibrometer studies of low momentum and hypervelocity impacts

NASA Astrophysics Data System (ADS)

Posada-Roman, Julio E.; Jackson, David A.; Cole, Mike J.; Garcia-Souto, Jose A.

2017-12-01

A multichannel optical fiber laser Doppler vibrometer was demonstrated with the capability of making simultaneous non-contact measurements of impacts at 3 different locations. Two sets of measurements were performed, firstly using small ball bearings (1 mm-5.5 mm) falling under gravity and secondly using small projectiles (1 mm) fired from an extremely high velocity light gas gun (LGG) with speeds in the range 1 km/s-8 km/s. Determination of impact damage is important for industries such as aerospace, military and rail, where the effect of an impact on the structure can result in a major structural damage. To our knowledge the research reported here demonstrates the first trials of a multichannel fiber laser Doppler vibrometer being used to detect hypervelocity impacts.

Corrosion Prevention of Rebar in Concrete in Critical Facilities Located in Coastal Environments at Okinawa

DTIC Science & Technology

2009-08-01

for affected structures and equipment amounts to hundreds of millions of dollars each year, and the degradation negatively impacts military readiness...protection to the rebar, but quantifying the extent of protection or positive impact on service life would require further monitoring and evaluation...sacrificial coating system interferes with the Galva Pulse measure- ment. It was therefore hard to quantitatively determine the impact on the corrosion rate

Outcrop-scale imaging spectroscopy of the Haughton impact structure, Canada

NASA Astrophysics Data System (ADS)

Greenberger, R. N.; Ehlmann, B. L.; Osinski, G. R.; Tornabene, L. L.; Green, R. O.

2016-12-01

Field-portable imaging spectrometers are a novel tool to study heterogeneous deposits such as those found at impact structures. Laboratory imaging spectroscopy of samples from the Haughton impact structure, Devon Island, Nunavut, Canada, detects and maps a variety of minerals within hand samples including calcite, dolomite, hydrated silica, gypsum, garnet, and iron oxides and sulfates. Many of these minerals originate from the target rock lithologies (e.g., limestone, dolostone, sandstone, gneiss) that have been shocked, altered, and displaced. An intimate mixture of quenched melts of calcite and hydrated silica is indicative of the melt rock matrix and is a byproduct of the impact process. Based on these preliminary results, we conducted a field campaign in Summer 2016 at the Haughton structure using imaging spectroscopy on the ground to study and quantify outcrops of impact-disrupted materials around the structure. Key questions addressed include (1) to what extent are the different impact-disrupted/exposed target lithologies from discrete stratigraphic units homogenized during impact processes, (2) what single or mixed lithologies are we able to detect, and (3) is variability within the target lithologies observable within the impactites? The Haughton impact structure is an ideal location to address these questions due to its excellent preservation and the nearly flat-lying, undeformed target rocks. We will present results from the field campaign along with supporting laboratory analyses. The results have implications for our understanding of impact processes and interpretation of planetary remote sensing datasets.

Descriptions and preliminary interpretations of cores recovered from the Manson Impact Structure (Iowa)

NASA Technical Reports Server (NTRS)

Anderson, R. R.; Witzke, B. J.; Hartung, J. B.; Shoemaker, E. M.; Roddy, D. J.

1993-01-01

A core drilling program initiated by the Iowa Geological Survey Bureau and U.S. Geological Survey in 1991 and 1992 collected 12 cores totalling over 1200 m from the Manson Impact Structure, a probable K-T boundary structure located in north-central Iowa. Cores were recovered from each of the major structural terranes, with 2 cores (M-3 and M-4) from the Terrace Terrane, 4 cores (M-2, M-2A, M-6, and M-9) from the Crater Moat, and 6 cores (M-1, M-5, M-7, M-8, M-10, and M-11) from the Central Peak. These supplemented 2 central peak cores (1-A and 2-A) drilled in 1953. The cores penetrated five major impact lithologies: (1) sedimentary clast breccia; (2) impact ejecta; (3) central peak crystallite rocks; (4) crystalline clast breccia with sandy matrix; and (5) crystallite clast breccia with a melt matrix. Descriptions and preliminary interpretations of these cores are presented.

Physical properties of glasses exposed to Earth-facing and trailing-side environments on LDEF

NASA Technical Reports Server (NTRS)

Wiedlocher, David E.; Kinser, Donald L.; Weller, Robert A.; Weeks, Robert A.; Mendenhall, Marcus H.

1993-01-01

The exposure of 108 glass samples and 12 glass-ceramic samples to Earth-orbit environments permitted measurements which establish the effects of each environment. Examination of five glass types and one glass ceramic located on both the Earth-facing side and the trailing edge revealed no reduction in strength within experimental limits. Strength measurements subjected less than 5 percent of the sample surface area to stresses above 90 percent of the glass's failure strength. Seven micrometeorite or space debris impacts occurred on trailing edge samples. One of those impacts occurred in a location which was subjected to 50 percent of the applied stress at failure. Micrometeorite or space debris impacts were not observed on Earth-facing samples. The physical shape and structure of the impact sites were carefully examined using stereographic scanning electron microscopy. These impacts induce a stress concentration at the damaged region which influences mechanical strength. The flaw size produced by such damage was examined to determine the magnitude of strength degradation in micrometeorite or space-debris impacted glasses. Scanning electron microscopy revealed topographical details of impact sites which included central melt zones and glass fiber production. The overall crater structure is similar to much larger impacts of large meteorite on the Moon in that the melt crater is surrounded by shocked regions of material which fracture zones and spall areas. Residual stresses arising from shock compression and cooling of the fused zone cannot currently be included in fracture mechanics analyses based on simple flaw size examination.

Structural and spectroscopic changes to natural nontronite induced by experimental impacts between 10 and 40 GPa

NASA Astrophysics Data System (ADS)

Friedlander, Lonia R.; Glotch, Timothy D.; Bish, David L.; Dyar, M. Darby; Sharp, Thomas G.; Sklute, Elizabeth C.; Michalski, Joseph R.

2015-05-01

Many phyllosilicate deposits remotely detected on Mars occur within bombarded terrains. Shock metamorphism from meteor impacts alters mineral structures, producing changed mineral spectra. Thus, impacts have likely affected the spectra of remotely sensed Martian phyllosilicates. We present spectral analysis results for a natural nontronite sample before and after laboratory-generated impacts over five peak pressures between 10 and 40 GPa. We conducted a suite of spectroscopic analyses to characterize the sample's impact-induced structural and spectral changes. Nontronite becomes increasingly disordered with increasing peak impact pressure. Every infrared spectroscopic technique used showed evidence of structural changes at shock pressures above ~25 GPa. Reflectance spectroscopy in the visible near-infrared region is primarily sensitive to the vibrations of metal-OH and interlayer H2O groups in the nontronite octahedral sheet. Midinfrared (MIR) spectroscopic techniques are sensitive to the vibrations of silicon and oxygen in the nontronite tetrahedral sheet. Because the tetrahedral and octahedral sheets of nontronite deform differently, impact-driven structural deformation may contribute to differences in phyllosilicate detection between remote sensing techniques sensitive to different parts of the nontronite structure. Observed spectroscopic changes also indicated that the sample's octahedral and tetrahedral sheets were structurally deformed but not completely dehydroxylated. This finding is an important distinction from previous studies of thermally altered phyllosilicates in which dehydroxylation follows dehydration in a stepwise progression preceding structural deformation. Impact alteration may thus complicate mineral-specific identifications based on the location of OH-group bands in remotely detected spectra. This is a key implication for Martian remote sensing arising from our results.

Structural Health Monitoring and Impact Detection Using Neural Networks for Damage Characterization

NASA Technical Reports Server (NTRS)

Ross, Richard W.

2006-01-01

Detection of damage due to foreign object impact is an important factor in the development of new aerospace vehicles. Acoustic waves generated on impact can be detected using a set of piezoelectric transducers, and the location of impact can be determined by triangulation based on the differences in the arrival time of the waves at each of the sensors. These sensors generate electrical signals in response to mechanical motion resulting from the impact as well as from natural vibrations. Due to electrical noise and mechanical vibration, accurately determining these time differentials can be challenging, and even small measurement inaccuracies can lead to significant errors in the computed damage location. Wavelet transforms are used to analyze the signals at multiple levels of detail, allowing the signals resulting from the impact to be isolated from ambient electromechanical noise. Data extracted from these transformed signals are input to an artificial neural network to aid in identifying the moment of impact from the transformed signals. By distinguishing which of the signal components are resultant from the impact and which are characteristic of noise and normal aerodynamic loads, the time differentials as well as the location of damage can be accurately assessed. The combination of wavelet transformations and neural network processing results in an efficient and accurate approach for passive in-flight detection of foreign object damage.

Social and place-focused communities in location-based online social networks

NASA Astrophysics Data System (ADS)

Brown, Chloë; Nicosia, Vincenzo; Scellato, Salvatore; Noulas, Anastasios; Mascolo, Cecilia

2013-06-01

Thanks to widely available, cheap Internet access and the ubiquity of smartphones, millions of people around the world now use online location-based social networking services. Understanding the structural properties of these systems and their dependence upon users' habits and mobility has many potential applications, including resource recommendation and link prediction. Here, we construct and characterise social and place-focused graphs by using longitudinal information about declared social relationships and about users' visits to physical places collected from a popular online location-based social service. We show that although the social and place-focused graphs are constructed from the same data set, they have quite different structural properties. We find that the social and location-focused graphs have different global and meso-scale structure, and in particular that social and place-focused communities have negligible overlap. Consequently, group inference based on community detection performed on the social graph alone fails to isolate place-focused groups, even though these do exist in the network. By studying the evolution of tie structure within communities, we show that the time period over which location data are aggregated has a substantial impact on the stability of place-focused communities, and that information about place-based groups may be more useful for user-centric applications than that obtained from the analysis of social communities alone.

Automated laser-based barely visible impact damage detection in honeycomb sandwich composite structures

NASA Astrophysics Data System (ADS)

Girolamo, D.; Girolamo, L.; Yuan, F. G.

2015-03-01

Nondestructive evaluation (NDE) for detection and quantification of damage in composite materials is fundamental in the assessment of the overall structural integrity of modern aerospace systems. Conventional NDE systems have been extensively used to detect the location and size of damages by propagating ultrasonic waves normal to the surface. However they usually require physical contact with the structure and are time consuming and labor intensive. An automated, contactless laser ultrasonic imaging system for barely visible impact damage (BVID) detection in advanced composite structures has been developed to overcome these limitations. Lamb waves are generated by a Q-switched Nd:YAG laser, raster scanned by a set of galvano-mirrors over the damaged area. The out-of-plane vibrations are measured through a laser Doppler Vibrometer (LDV) that is stationary at a point on the corner of the grid. The ultrasonic wave field of the scanned area is reconstructed in polar coordinates and analyzed for high resolution characterization of impact damage in the composite honeycomb panel. Two methodologies are used for ultrasonic wave-field analysis: scattered wave field analysis (SWA) and standing wave energy analysis (SWEA) in the frequency domain. The SWA is employed for processing the wave field and estimate spatially dependent wavenumber values, related to discontinuities in the structural domain. The SWEA algorithm extracts standing waves trapped within damaged areas and, by studying the spectrum of the standing wave field, returns high fidelity damage imaging. While the SWA can be used to locate the impact damage in the honeycomb panel, the SWEA produces damage images in good agreement with X-ray computed tomographic (X-ray CT) scans. The results obtained prove that the laser-based nondestructive system is an effective alternative to overcome limitations of conventional NDI technologies.

Utilization of Titanium Particle Impact Location to Validate a 3D Multicomponent Model for Cold Spray Additive Manufacturing

NASA Astrophysics Data System (ADS)

Faizan-Ur-Rab, M.; Zahiri, S. H.; King, P. C.; Busch, C.; Masood, S. H.; Jahedi, M.; Nagarajah, R.; Gulizia, S.

2017-12-01

Cold spray is a solid-state rapid deposition technology in which metal powder is accelerated to supersonic speeds within a de Laval nozzle and then impacts onto the surface of a substrate. It is possible for cold spray to build thick structures, thus providing an opportunity for melt-less additive manufacturing. Image analysis of particle impact location and focused ion beam dissection of individual particles were utilized to validate a 3D multicomponent model of cold spray. Impact locations obtained using the 3D model were found to be in close agreement with the empirical data. Moreover, the 3D model revealed the particles' velocity and temperature just before impact—parameters which are paramount for developing a full understanding of the deposition process. Further, it was found that the temperature and velocity variations in large-size particles before impact were far less than for the small-size particles. Therefore, an optimal particle temperature and velocity were identified, which gave the highest deformation after impact. The trajectory of the particles from the injection point to the moment of deposition in relation to propellant gas is visualized. This detailed information is expected to assist with the optimization of the deposition process, contributing to improved mechanical properties for additively manufactured cold spray titanium parts.

Planar location of the simulative acoustic source based on fiber optic sensor array

NASA Astrophysics Data System (ADS)

Liang, Yi-Jun; Liu, Jun-feng; Zhang, Qiao-ping; Mu, Lin-lin

2010-06-01

A fiber optic sensor array which is structured by four Sagnac fiber optic sensors is proposed to detect and locate a simulative source of acoustic emission (AE). The sensing loops of Sagnac interferometer (SI) are regarded as point sensors as their small size. Based on the derived output light intensity expression of SI, the optimum work condition of the Sagnac fiber optic sensor is discussed through the simulation of MATLAB. Four sensors are respectively placed on a steel plate to structure the sensor array and the location algorithms are expatiated. When an impact is generated by an artificial AE source at any position of the plate, the AE signal will be detected by four sensors at different times. With the help of a single chip microcomputer (SCM) which can calculate the position of the AE source and display it on LED, we have implemented an intelligent detection and location.

Earth Observation

NASA Image and Video Library

2011-07-06

ISS028-E-014782 (6 July 2011) --- The Shoemaker (formerly Teague) Impact Structure, located in Western Australia in a drainage basin south of the Waldburg Range, presents an other-worldly appearance in this detailed photograph recorded from onboard the International Space Station on July 6. The Shoemaker impact site is approximately 30 kilometers in diameter, and is clearly defined by concentric ring structures formed in sedimentary rocks (brown to dark brown, image center) that were deformed by the impact event approximately 1630 million years ago, according to the Earth Impact Database. Several saline and ephemeral lakes?Nabberu, Teague, Shoemaker, and numerous smaller ponds?occupy the land surface between the concentric ring structures. Differences in color result from both water depth and suspended sediments, with some bright salt crusts visible around the edges of smaller ponds (image center The Teague Impact Structure was renamed Shoemaker in honor of the late Dr. Eugene M. Shoemaker, a pioneer in the field of impact crater studies and planetary geology, and founder of the Astrogeology Branch of the United States Geological Survey. The image was recorded with a digital still camera using a 200 mm lens, and is provided by the ISS Crew Earth Observations experiment and Image Science & Analysis Laboratory, Johnson Space Center.

Geo - hydrological investigations and impact of water harvesting structures on groundwater potential in Anantapur District, Andhra Pradesh, India.

PubMed

Suryanarayana, K V; Krishnaiah, S; Khokalay, Murthy Rao V

2010-10-01

In this paper, the data pertaining to the rainfall, its departure from normal, moving mean rainfall, depth of water levels in pre-monsoon and post-monsoon seasons, groundwater availability, groundwater utilization and impact of storage of water in large water bodies are analyzed graphically. The results indicate that the groundwater is over exploited in many places in Anantapur District (India). The groundwater levels found fluctuating, when compared the observations in pre-monsoon and post-monsoon seasons. Hence, it is concluded that the construction of water harvesting structures at suitable locations will have a definite impact on the groundwater potential in Anantapur District.

New Observations at the Slate Islands Impact Structure, Lake Superior

NASA Technical Reports Server (NTRS)

Dressler, B. O.; Sharpton, V. L.; Schnieders, B.; Scott, J.

1995-01-01

Slate Islands, a group of 2 large and several small islands, is located in northern Lake Superior, approximately 10 km south of Terrace Bay. Shatter cones, breccias and shock metamorphic features provide evidence that the Slate Islands Structure was formed as a result of asteroid or comet impact. Most of the island group is believed to represent the central uplift of a complex impact crater. The structure possibly has a diameter of about 32 km. For Sage (1978, 1991) shock metamorphic features, shatter cones and pervasive rock brecciation are the results of diatreme activity. The present investigations represent the second year of a co-operative study of the Lunar and Planetary Institute, Houston, Texas and the Field Services Section (Northwest) of the Ontario Geological Survey. The objective of this investigation is to come to a better understanding of the formation of mid-size impact structures on Earth and the planets of the solar system. Impact processes played a fundamental role in the formation of the planets and the evolution of life on Earth. Meteorite and comet impacts are not a phenomenon of the past. Last year, more than 20 pieces of the Shoemaker-Levy 9 impacted on Jupiter and the Tunguska comet impacted in Siberia in the early years of this century. The study of impact processes is a relatively young part of geoscience and much is still to be learnt by detailed field and laboratory investigations. The State Islands Structure has been selected for the present detailed investigations because of the excellent shoreline outcrops of rock units related to the impact. The structure is a complex impact crater that has been eroded so that important lithological and structural elements are exposed. We know of no other mid-size terrestrial impact structure with equal or better exposures. In this publication we present preliminary results of our 1994 and 1995 field and laboratory investigations. We have tentatively identified a few impact melt and a considerable number of suevite occurrences.

Economic impact of closing low-volume rural bridges.

DOT National Transportation Integrated Search

2013-02-01

The State of Kansas has approximately 25,464 bridges that are located on the state, county and : city roadway network. As the infrastructure in Kansas ages, bridges can become structurally : deficient or functionally obsolete. The Kansas Department o...

The Rock Elm meteorite impact structure, Wisconsin: Geology and shock-metamorphic effects in quartz

USGS Publications Warehouse

French, B.M.; Cordua, W.S.; Plescia, J.B.

2004-01-01

The Rock Elm structure in southwest Wisconsin is an anomalous circular area of highly deformed rocks, ???6.5 km in diameter, located in a region of virtually horizontal undeformed sedimentary rocks. Shock-produced planar microstructures (PMs) have been identified in quartz grains in several lithologies associated with the structure: sandstones, quartzite pebbles, and breccia. Two distinct types of PMs are present: P1 features, which appear identical to planar fractures (PFs or cleavage), and P2 features, which are interpreted as possible incipient planar deformation features (PDFs). The latter are uniquely produced by the shock waves associated with meteorite impact events. Both types of PMs are oriented parallel to specific crystallographic planes in the quartz, most commonly to c(0001), ??112??2, and r/z101??1. The association of unusual, structurally deformed strata with distinct shock-produced microdeformation features in their quartz-bearing rocks establishes Rock Elm as a meteorite impact structure and supports the view that the presence of multiple parallel cleavages in quartz may be used independently as a criterion for meteorite impact. Preliminary paleontological studies indicate a minimum age of Middle Ordovician for the Rock Elm structure. A similar age estimate (450-400 Ma) is obtained independently by combining the results of studies of the general morphology of complex impact structures with estimated rates of sedimentation for the region. Such methods may be applicable to dating other old and deeply eroded impact structures formed in sedimentary target rocks.

Bacterial community and arsenic functional genes diversity in arsenic contaminated soils from different geographic locations

PubMed Central

Gu, Yunfu; D. Van Nostrand, Joy; Wu, Liyou; He, Zhili; Qin, Yujia; Zhao, Fang-Jie; Zhou, Jizhong

2017-01-01

To understand how soil microbial communities and arsenic (As) functional genes respond to soil arsenic (As) contamination, five soils contaminated with As at different levels were collected from diverse geographic locations, incubated for 54 days under flooded conditions, and examined by both MiSeq sequencing of 16S rRNA gene amplicons and functional gene microarray (GeoChip 4.0). The results showed that both bacterial community structure and As functional gene structure differed among geographical locations. The diversity of As functional genes correlated positively with the diversity of 16S rRNA genes (P< 0.05). Higher diversities of As functional genes and 16S rRNA genes were observed in the soils with higher available As. Soil pH, phosphate-extractable As, and amorphous Fe content were the most important factors in shaping the bacterial community structure and As transformation functional genes. Geographic location was also important in controlling both the bacterial community and As transformation functional potential. These findings provide insights into the variation of As transformation functional genes in soils contaminated with different levels of As at different geographic locations, and the impact of environmental As contamination on the soil bacterial community. PMID:28475654

Transducer placement for robustness to variations in boundary conditions for active structural acoustic control

NASA Astrophysics Data System (ADS)

Sprofera, Joseph D.; Clark, Robert L.; Cabell, Randolph H.; Gibbs, Gary P.

2005-05-01

Turbulent boundary layer (TBL) noise is considered a primary contribution to the interior noise present in commercial airliners. There are numerous investigations of interior noise control devoted to aircraft panels; however, practical realization is a potential challenge since physical boundary conditions are uncertain at best. In most prior studies, pinned or clamped boundary conditions were assumed; however, realistic panels likely display a range of boundary conditions between these two limits. Uncertainty in boundary conditions is a challenge for control system designers, both in terms of the compensator implemented and the location of transducers required to achieve the desired control. The impact of model uncertainties, specifically uncertain boundaries, on the selection of transducer locations for structural acoustic control is considered herein. The final goal of this work is the design of an aircraft panel structure that can reduce TBL noise transmission through the use of a completely adaptive, single-input, single-output control system. The feasibility of this goal is demonstrated through the creation of a detailed analytical solution, followed by the implementation of a test model in a transmission loss apparatus. Successfully realizing a control system robust to variations in boundary conditions can lead to the design and implementation of practical adaptive structures that could be used to control the transmission of sound to the interior of aircraft. Results from this research effort indicate it is possible to optimize the design of actuator and sensor location and aperture, minimizing the impact of boundary conditions on the desired structural acoustic control.

Imparting Barely Visible Impact Damage to a Stitched Composite Large-Scale Pressure Box

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.; Przekop, Adam

2016-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body (HWB) aircraft configuration, which has been a focus of the NASA Environmentally Responsible Aviation Project. The NASA-Boeing structural development for the HWB aircraft culminated in testing of the multi-bay box, which is an 80%-scale representation of the pressurized center-body section. This structure was tested in the NASA Langley Research Center Combined Loads Test System facility. As part of this testing, barely visible impact damage was imparted to the interior and exterior of the test article to demonstrate compliance with a condition representative of the requirements for Category 1 damaged composite structure as defined by the Federal Aviation Regulations. Interior impacts were imparted using an existing spring-loaded impactor, while the exterior impacts were imparted using a newly designed, gravity-driven impactor. This paper describes the impacts to the test article, and the design of the gravitydriven guided-weight impactor. The guided-weight impactor proved to be a very reliable method to impart barely visible impact damage in locations which are not easily accessible for a traditional drop-weight impactor, while at the same time having the capability to be highly configurable for use on other aircraft structures.

Community investment in wind farms: funding structure effects in wind energy infrastructure development.

PubMed

Beery, Joshua A; Day, Jennifer E

2015-03-03

Wind energy development is an increasingly popular form of renewable energy infrastructure in rural areas. Communities generally perceive socioeconomic benefits accrue and that community funding structures are preferable to corporate structures, yet lack supporting quantitative data to inform energy policy. This study uses the Everpower wind development, to be located in Midwestern Ohio, as a hypothetical modeling environment to identify and examine socioeconomic impact trends arising from corporate, community and diversified funding structures. Analysis of five National Renewable Energy Laboratory Jobs and Economic Development Impact models incorporating local economic data and review of relevant literature were conducted. The findings suggest that community and diversified funding structures exhibit 40-100% higher socioeconomic impact levels than corporate structures. Prioritization of funding sources and retention of federal tax incentives were identified as key elements. The incorporation of local shares was found to mitigate the negative effects of foreign private equity, local debt financing increased economic output and opportunities for private equity investment were identified. The results provide the groundwork for energy policies focused to maximize socioeconomic impacts while creating opportunities for inclusive economic participation and improved social acceptance levels fundamental to the deployment of renewable energy technology.

The Oasis impact structure, Libya: geological characteristics from ALOS PALSAR-2 data interpretation

NASA Astrophysics Data System (ADS)

van Gasselt, Stephan; Kim, Jung Rack; Choi, Yun-Soo; Kim, Jaemyeong

2017-02-01

Optical and infrared remote sensing may provide first-order clues for the identification of potential impact structures on the Earth. Despite the free availability of at least optical image data at highest resolution, research has shown that remote sensing analysis always remains inconclusive and extensive groundwork is needed for the confirmation of the impact origin of such structures. Commonly, optical image data and digital terrain models have been employed mainly for such remote sensing studies of impact structures. With the advent of imaging radar data, a few excursions have been made to also employ radar datasets. Despite its long use, capabilities of imaging radar for studying surface and subsurface structures have not been exploited quantitatively when applied for the identification and description of such features due to the inherent complexity of backscatter processes. In this work, we make use of higher-level derived radar datasets in order to gain clearer qualitative insights that help to describe and identify potential impact structures. We make use of high-resolution data products from the ALOS PALSAR-1 and ALOS PALSAR-2 L-band sensors to describe the heavily eroded Oasis impact structure located in the Libyan Desert. While amplitude radar data with single polarization have usually been utilized to accompany the suite of remote sensing datasets when interpreting impact structures in the past, we conclude that the integration of amplitude data with HH/HV/HH-HV polarization modes in standard and, in particular, in Ultra-Fine mode, as well as entropy-alpha decomposition data, significantly helps to identify and discriminate surface units based on their consolidation. Based on the overarching structural pattern, we determined the diameter of the eroded Oasis structure at 15.6 ± 0.5 km.

Use of a New Portable Instrumented Impactor on the NASA Composite Crew Module Damage Tolerance Program

NASA Technical Reports Server (NTRS)

Jackson, Wade C.; Polis, Daniel L.

2014-01-01

Damage tolerance performance is critical to composite structures because surface impacts at relatively low energies may result in a significant strength loss. For certification, damage tolerance criteria require aerospace vehicles to meet design loads while containing damage at critical locations. Data from standard small coupon testing are difficult to apply to larger more complex structures. Due to the complexity of predicting both the impact damage and the residual properties, damage tolerance is demonstrated primarily by testing. A portable, spring-propelled, impact device was developed which allows the impact damage response to be investigated on large specimens, full-scale components, or entire vehicles. During impact, both the force history and projectile velocity are captured. The device was successfully used to demonstrate the damage tolerance performance of the NASA Composite Crew Module. The impactor was used to impact 18 different design features at impact energies up to 35 J. Detailed examples of these results are presented, showing impact force histories, damage inspection results, and response to loading.

Anthropogenic impact on diazotrophic diversity in the mangrove rhizosphere revealed by nifH pyrosequencing

PubMed Central

Jing, Hongmei; Xia, Xiaomin; Liu, Hongbin; Zhou, Zhi; Wu, Chen; Nagarajan, Sanjay

2015-01-01

Diazotrophs in the mangrove rhizosphere play a major role in providing new nitrogen to the mangrove ecosystem and their composition and activity are strongly influenced by anthropogenic activity and ecological conditions. In this study, the diversity of the diazotroph communities in the rhizosphere sediment of five tropical mangrove sites with different levels of pollution along the north and south coastline of Singapore were studied by pyrosequencing of the nifH gene. Bioinformatics analysis revealed that in all the studied locations, the diazotroph communities comprised mainly of members of the diazotrophic cluster I and cluster III. The detected cluster III diazotrophs, which were composed entirely of sulfate-reducing bacteria, were more abundant in the less polluted locations. The metabolic capacities of these diazotrophs indicate the potential for bioremediation and resiliency of the ecosystem to anthropogenic impact. In heavily polluted locations, the diazotrophic community structures were markedly different and the diversity of species was significantly reduced when compared with those in a pristine location. This, together with the increased abundance of Marinobacterium, which is a bioindicator of pollution, suggests that anthropogenic activity has a negative impact on the genetic diversity of diazotrophs in the mangrove rhizosphere. PMID:26539189

Anthropogenic impact on diazotrophic diversity in the mangrove rhizosphere revealed by nifH pyrosequencing.

PubMed

Jing, Hongmei; Xia, Xiaomin; Liu, Hongbin; Zhou, Zhi; Wu, Chen; Nagarajan, Sanjay

2015-01-01

Diazotrophs in the mangrove rhizosphere play a major role in providing new nitrogen to the mangrove ecosystem and their composition and activity are strongly influenced by anthropogenic activity and ecological conditions. In this study, the diversity of the diazotroph communities in the rhizosphere sediment of five tropical mangrove sites with different levels of pollution along the north and south coastline of Singapore were studied by pyrosequencing of the nifH gene. Bioinformatics analysis revealed that in all the studied locations, the diazotroph communities comprised mainly of members of the diazotrophic cluster I and cluster III. The detected cluster III diazotrophs, which were composed entirely of sulfate-reducing bacteria, were more abundant in the less polluted locations. The metabolic capacities of these diazotrophs indicate the potential for bioremediation and resiliency of the ecosystem to anthropogenic impact. In heavily polluted locations, the diazotrophic community structures were markedly different and the diversity of species was significantly reduced when compared with those in a pristine location. This, together with the increased abundance of Marinobacterium, which is a bioindicator of pollution, suggests that anthropogenic activity has a negative impact on the genetic diversity of diazotrophs in the mangrove rhizosphere.

Novel Structural Health Monitoring Schemes for Glass-Fiber Composites using Nanofillers

DTIC Science & Technology

2014-03-31

laminate with aligned carbon black. EIT has also been used to locate damage in a carbon nanofiber (CNF) filled epoxy composite. Methods of improving EIT...mm in diameter as well as impact damage to a GFRP laminate with aligned carbon black. EIT has also been used to locate damage in a carbon nanofiber...field applications, particularly ballistic armor and helicopter blades. The ability to detect matrix damage in composite laminates is extremely

The Human Element of Project Management

ERIC Educational Resources Information Center

Gillard, Sharlett

2017-01-01

Much research and dialogue have been published about project management. Studies have been conducted regarding the impact of size, member location, gender composition, cross-functional structure, stakeholder influence, confidence issues, technology usage, management style, generational differences, technical expertise vs. people skills, and a…

Experimental Study on Stress Monitoring of Sand-Filled Steel Tube during Impact Using Piezoceramic Smart Aggregates.

PubMed

Du, Guofeng; Zhang, Juan; Zhang, Jicheng; Song, Gangbing

2017-08-22

The filling of thin-walled steel tubes with quartz sand can help to prevent the premature buckling of the steel tube at a low cost. During an impact, the internal stress of the quartz sand-filled steel tube column is subjected to not only axial force but also lateral confining force, resulting in complicated internal stress. A suitable sensor for monitoring the internal stress of such a structure under an impact is important for structural health monitoring. In this paper, piezoceramic Smart Aggregates (SAs) are embedded into a quartz Sand-Filled Steel Tube Column (SFSTC) to monitor the internal structural stress during impacts. The piezoceramic smart aggregates are first calibrated by an impact hammer. Tests are conducted to study the feasibility of monitoring the internal stress of a structure. The results reflect that the calibration value of the piezoceramic smart aggregate sensitivity test is in good agreement with the theoretical value, and the output voltage value of the piezoceramic smart aggregate has a good linear relationship with external forces. Impact tests are conducted on the sand-filled steel tube with embedded piezoceramic smart aggregates. By analyzing the output signal of the piezoceramic smart aggregates, the internal stress state of the structure can be obtained. Experimental results demonstrated that, under the action of impact loads, the piezoceramic smart aggregates monitor the compressive stress at different locations in the steel tube, which verifies the feasibility of using piezoceramic smart aggregate to monitor the internal stress of a structure.

Variations in Grain-Scale Sediment Structure in a Gravel-Bed Channel as a Function of Fine Sediment Content and Morphological Location

NASA Astrophysics Data System (ADS)

Voepel, H.; Ahmed, S. I.; Hodge, R. A.; Leyland, J.; Sear, D. A.

2016-12-01

One of the major causes of uncertainty in estimates of bedload transport rates in gravel bed rivers is a lack of understanding of grain-scale sediment structure, and the impact that this structure has on bed stability. Furthermore, grain-scale structure varies throughout a channel and over time in ways that have not been fully quantified. Our research aims to quantify variations in sediment structure caused by two key variables; morphological location within a riffle-pool sequence (reflecting variation in hydraulic conditions), and the fine sediment content of the gravel bed (sand and clay). We report results from a series of flume experiments in which we water-worked a gravel bed with a riffle-pool morphology. The fine sediment content of the bed was incrementally increased over a series of runs from gravel only, to coarse sand, fine sand and two concentrations of clay. After each experimental run intact samples of the bed at different locations were extracted and the internal structure of the bed was measured using non-destructive, micro-focus X-ray computed tomography (CT) imaging. The CT images were processed to measure the properties of individual grains, including volume, center of mass, dimension, and contact points. From these data we were able to quantify the sediment structure through metrics including measurement of grain pivot angles, grain exposure and protrusion, and vertical variation in bed porosity and fine sediment content. Metrics derived from the CT data were verified using data from grain counts and tilt-table measurements on co-located samples. Comparison of the metrics across different morphological locations and fine sediment content demonstrates how these factors affect the bed structure. These results have implications for the development of sediment entrainment models for gravel bed rivers.

Damage detection of an in-service condensation pipeline joint

NASA Astrophysics Data System (ADS)

Briand, Julie; Rezaei, Davood; Taheri, Farid

2010-04-01

The early detection of damage in structural or mechanical systems is of vital importance. With early detection, the damage may be repaired before the integrity of the system is jeopardized, resulting in monetary losses, loss of life or limb, and environmental impacts. Among the various types of structural health monitoring techniques, vibration-based methods are of significant interest since the damage location does not need to be known beforehand, making it a more versatile approach. The non-destructive damage detection method used for the experiments herein is a novel vibration-based method which uses an index called the EMD Energy Damage Index, developed with the aim of providing improved qualitative results compared to those methods currently available. As part of an effort to establish the integrity and limitation of this novel damage detection method, field testing was completed on a mechanical pipe joint on a condensation line, located in the physical plant of Dalhousie University. Piezoceramic sensors, placed at various locations around the joint were used to monitor the free vibration of the pipe imposed through the use of an impulse hammer. Multiple damage progression scenarios were completed, each having a healthy state and multiple damage cases. Subsequently, the recorded signals from the healthy and damaged joint were processed through the EMD Energy Damage Index developed in-house in an effort to detect the inflicted damage. The proposed methodology successfully detected the inflicted damages. In this paper, the effects of impact location, sensor location, frequency bandwidth, intrinsic mode functions, and boundary conditions are discussed.

The Vredefort Dome: Review of geology and deformation phenomena and status report on current knowledge and remaining problematics (five years after the cryptoexplosion workshop)

NASA Technical Reports Server (NTRS)

Reimold, W. U.

1992-01-01

The Vredefort structure located in the center of the Witwatersrand basin in South Africa and the Sudbury structure in Canada are widely considered the two oldest and largest impact structures still evident on Earth. Both structures are very similar in a number of geological aspects (e.g., association with major economic ore deposits, similar ages of ca. 2 Ga, abundant pseudotachylite as well as shatter cone occurrences, overturned collar). However, whereas the geological community generally accepts an impact origin for the Sudbury structure, a number of researchers are still reluctant to accept this for the Vredefort Dome. Therefore, the aim of this review is to present new data, highlight the most obvious shortcomings in the current database, and to summarize the major arguments in the genetic controversy.

Revisiting the West Clearwater Lake Impact Structure, Canada

NASA Technical Reports Server (NTRS)

Osinski, G. R.; Brunner, A.; Collins, G.; Cohen, B. A.; Coulter, A.; Elphic, R.; Grieve, R. A. F.; Hodges, K.; Horne, A.; Kerrigan, M.

2015-01-01

The West and East Clearwater Lake impact structures are two of the most distinctive and recognizable impact structures on Earth. Known regionally as the "Clearwater Lake Complex", these structures are located in northern Quebec, Canada (56 deg 10 N, 74 deg 20 W) approximately 125 km east of Hudson Bay. The currently accepted diameters are 36 km and 26 km for the West and East structures, respectively. Long thought to represent a rare example of a double impact, recent age dating has called this into question with ages of approximately 286 Ma and approximately 460-470 Ma being proposed for the West and East structures, respectively. Relatively little is known about the East Clearwater Lake structure. There is no surface exposure and what information there is comes from geophysics and two drill cores obtained in the 1960s. In contrast, the West Clearwater Lake structure is relatively well preserved with large ring of islands in the approximately 30 km diameter lake. Much of the work done on West Clearwater stems from field investigations carried out in 1977 driven by the Apollo program, with a focus on the impact melt rocks and other impactites, which are well exposed on the ring of islands. To our knowledge, the Clearwater Lake impact structures have not been the focus of detailed impact geology field investigations since the 1977 expedition and the only geological map that exists is from the 1960s and is at the reconnaissance level. Our knowledge of impact cratering processes have increased substantially since this time, as have the analytical techniques available for samples. This provided the motivation for a joint Canadian-US-UK expedition to the West Clearwater Lake impact structure in August and September 2015, under the auspices of the FINESSE (Field Investigations to Enable Solar System Science and Exploration) project, part of NASA's Solar System Exploration Research Virtual Institute (SSERVI). We focus here on the impactites of the West Clearwater Lake impact structure. Other ongoing studies, also presented at this conference, focus on central uplift formation, the impact-generated hydrothermal system, xxxx and using WCIS as an analog test site for crew studies of sampling protocols].

Application of wavefield imaging to characterize scattering from artificial and impact damage in composite laminate panels

NASA Astrophysics Data System (ADS)

Williams, Westin B.; Michaels, Thomas E.; Michaels, Jennifer E.

2018-04-01

Composite materials used for aerospace applications are highly susceptible to impacts, which can result in barely visible delaminations. Reliable and fast detection of such damage is needed before structural failures occur. One approach is to use ultrasonic guided waves generated from a sparse array consisting of permanently mounted or embedded transducers for performing structural health monitoring. This array can detect introduction of damage after baseline subtraction, and also provide localization and characterization information via the minimum variance imaging algorithm. Imaging performance can vary considerably depending upon where damage is located with respect to the array; however, prior work has shown that knowledge of expected scattering can improve imaging consistency for artificial damage at various locations. In this study, anisotropic material attenuation and wave speed are estimated as a function of propagation angle using wavefield data recorded along radial lines at multiple angles with respect to an omnidirectional guided wave source. Additionally, full wavefield data are recorded before and after the introduction of artificial and impact damage so that wavefield baseline subtraction may be applied. 3-D filtering techniques are then used to reduce noise and isolate scattered waves. A model for estimating scattering of a circular defect is developed and scattering estimates for both artificial and impact damage are presented and compared.

Cartographic modeling of snow avalanche path location within Glacier National Park, Montana

NASA Technical Reports Server (NTRS)

Walsh, Stephen J.; Brown, Daniel G.; Bian, Ling; Butler, David R.

1990-01-01

Geographic information system (GIS) techniques were applied to the study of snow-avalanche path location within Glacier National Park, Montana. Aerial photointerpretation and field surveys confirmed the location of 121 avalanche paths within the selected study area. Spatial and nonspatial information on each path were integrated using the ARC/INFO GIS. Lithologic, structural, hydrographic, topographic, and land-cover impacts on path location were analyzed. All path frequencies within variable classes were normalized by the area of class occurrence relative to the total area of the study area and were added to the morphometric information contained within INFO tables. The normalized values for each GIS coverage were used to cartographically model, by means of composite factor weightings, avalanche path locations.

Differences in the impacts of formal and informal recreational trails on urban forest loss and tree structure.

PubMed

Ballantyne, Mark; Pickering, Catherine Marina

2015-08-15

Recreational trails are one of the most common types of infrastructure used for nature-based activities such as hiking and mountain biking worldwide. Depending on their design, location, construction, maintenance and use, these trails differ in their environmental impacts. There are few studies, however, comparing the impacts of different trail types including between formal management-created trails and informal visitor-created trails. Although both types of trails can be found in remote natural areas, dense networks of them often occur in forests close to cities where they experience intense visitor use. To assess the relative impacts of different recreational trails in urban forests, we compared the condition of the trail surface, loss of forest strata and changes in tree structure caused by seven types of trails (total network 46.1 km) traversing 17 remnants of an endangered urban forest in Australia. After mapping and classifying all trails, we assessed their impact on the forest condition at 125 sites (15 sites per trail type, plus 15 control sites within undisturbed forest). On the trail sites, the condition of the trail surface, distance from the trail edge to four forest strata (litter, understory, midstorey and tree cover) and structure of the tree-line were assessed. Informal trails generally had poorer surface conditions and were poorly-designed and located. Per site, formal and informal trails resulted in similar loss of forest strata, with wider trails resulting in greater loss of forest. Because there were more informal trails, however, they accounted for the greatest cumulative forest loss. Structural impacts varied, with the widest informal trails and all formal hardened trails resulting in similar reductions in canopy cover and tree density but an increase in saplings. These structural impacts are likely a function of the unregulated and intense use of large informal trails, and disturbance from the construction and maintenance of formal trails. The results demonstrate that different types of recreational trails vary in the type and range of impacts they cause to forests. They highlight the importance of careful consideration towards management options when dealing with trail networks especially in areas of high conservation value. Copyright © 2015 Elsevier Ltd. All rights reserved.

78 FR 76593 - Guarantee Fee Rates for Guaranteed Loans for Fiscal Year 2014; Maximum Portion of Guarantee...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-18

... impact business investment as defined in 7 CFR 4279.155(b)(5) and be located in rural communities that... trauma as a result of natural disaster, or are experiencing fundamental structural changes in its...

Gravity investigation of the Manson impact structure, Iowa

NASA Technical Reports Server (NTRS)

Plescia, J. B.

1993-01-01

The Manson crater, of probable Cretaceous/Tertiary age, is located in northwestern Iowa (center at 42 deg. 34.44 min N; 94 deg. 33.60 min W). A seismic reflection profile along an east west line across the crater and drill hole data indicate a crater about 35 km in diameter having the classic form for an impact crater, an uplifted central peak composed of uplifted Proterozoic crystalline bedrock, surrounded by a 'moat' filled with impact produced breccia and a ring graben zone composed of tilted fault blocks of the Proterozoic and Paleozoic country rocks. The structure has been significantly eroded. This geologic structure would be expected to produce a significant gravity signature and study of that signature would shed additional light on the details of the crater structure. A gravity study was undertaken to better resolve the crustal structure. The regional Bouguer gravity field is characterized by a southeastward decreasing field. To first order, the Bouguer gravity field can be understood in the context of the geology of the Precambrian basement. The high gravity at the southeast corner is associated with the mid-continent gravity high; the adjacent low to the northwest results from a basin containing low-density clastic sediments shed from the basement high. Modeling of a simple basin and adjacent high predicts much of the observed Bouguer gravity signature. A gravity signature due to structure associated with the Manson impact is not apparent in the Bouguer data. To resolve the gravity signature of the impact, a series of polynomial surfaces were fit to the Bouguer gravity field to isolate the small wavelength residual anomalies. The residual gravity obtained after subtracting a 5th- or 6th-order polynomial seems to remove most of the regional effects and isolate local anomalies. The pattern resolved in the residual gravity is one of a gravity high surrounded by gravity lows and in turn surrounded by isolated gravity highs. The central portion of the crater is characterized by two positive anomalies having amplitudes of about plus 4 mGal separated by a gentle saddle located approximately at the crater center.

Noachian and Hesperian modification of the original Chryse impact basin topography

NASA Technical Reports Server (NTRS)

Stockman, Stephanie; Frey, Herbert

1994-01-01

We propose a new center (35.5 W, 32.5 N) and ring assignment for the original Chryse impact basin based on photogeologic mapping and re-examination of the published geology. Noachian features in the Chryse Planitia area are the best indicators of the original ancient multiringed impact structure. While other workers have centered the Chryse impact on the topographic low associated with Hesperian volcanic and fluvial deposits, we suggest that the center of the original Noachian-age excavation cavity was located 800 km farther NE, and the basin topography was significantly modified over time.

Impact and vibration detection in composite materials by using intermodal interference in multimode optical fibers

NASA Astrophysics Data System (ADS)

Malki, Abdelrafik; Gafsi, Rachid; Michel, Laurent; Labarrère, Michel; Lecoy, Pierre

1996-09-01

An optical fiber sensor based on the intermodal interference principle is integrated in a composite material to detect impacts and vibrations. Six fibers are integrated at the top of a carbon/epoxy composite panel so as to form a grid into the structure. Spectral and temporal responses to impacts and acoustic vibrations of the sensor are compared with a piezoelectric accelerometer. The tests proved the facility of integration and the high sensitivity of the device. The location of impacts is performed with this arrangement by measuring the arrival times of the front waves to the fibers.

Non-Destructive Inspection of Impact Damage in Composite Aircraft Panels by Ultrasonic Guided Waves and Statistical Processing.

PubMed

Capriotti, Margherita; Kim, Hyungsuk E; Scalea, Francesco Lanza di; Kim, Hyonny

2017-06-04

This paper discusses a non-destructive evaluation (NDE) technique for the detection of damage in composite aircraft structures following high energy wide area blunt impact (HEWABI) from ground service equipment (GSE), such as heavy cargo loaders and other heavy equipment. The test structures typically include skin, co-cured stringers, and C-frames that are bolt-connected onto the skin with shear ties. The inspection exploits the waveguide geometry of these structures by utilizing ultrasonic guided waves and a line scan approach. Both a contact prototype and a non-contact prototype were developed and tested on realistic test panels subjected to impact in the laboratory. The results are presented in terms of receiver operating characteristic curves that show excellent probability of detection with low false alarm rates for defects located in the panel skin and stringers.

Non-Destructive Inspection of Impact Damage in Composite Aircraft Panels by Ultrasonic Guided Waves and Statistical Processing

PubMed Central

Capriotti, Margherita; Kim, Hyungsuk E.; Lanza di Scalea, Francesco; Kim, Hyonny

2017-01-01

This paper discusses a non-destructive evaluation (NDE) technique for the detection of damage in composite aircraft structures following high energy wide area blunt impact (HEWABI) from ground service equipment (GSE), such as heavy cargo loaders and other heavy equipment. The test structures typically include skin, co-cured stringers, and C-frames that are bolt-connected onto the skin with shear ties. The inspection exploits the waveguide geometry of these structures by utilizing ultrasonic guided waves and a line scan approach. Both a contact prototype and a non-contact prototype were developed and tested on realistic test panels subjected to impact in the laboratory. The results are presented in terms of receiver operating characteristic curves that show excellent probability of detection with low false alarm rates for defects located in the panel skin and stringers. PMID:28772976

SRM attrition rate study of the aft motor case segments due to water impact cavity collapse loading

NASA Technical Reports Server (NTRS)

Crockett, C. D.

1976-01-01

The attrition assessment of the aft segments of Solid Rocket Motor due to water impact requires the establishment of a correlation between loading occurrences and structural capability. Each discrete load case, as identified by the water impact velocities and angle, varies longitudinally and radially in magnitude and distribution of the external pressure. The distributions are further required to be shifted forward or aft one-fourth the vehicle diameter to assure minimization of the effect of test instrumentation location for the load determinations. The asymmetrical load distributions result in large geometric nonlinearities in structural response. The critical structural response is progressive buckling of the case. Discrete stiffeners have been added to these aft segments to aid in gaining maximum structural capability for minimum weight addition for resisting these loads. This report presents the development of the attrition assessment of the aft segments and includes the rationale for eliminating all assessable conservatisms from this assessment.

Numerical Investigation of the Consequences of Land Impacts, Water Impacts, or Air Bursts of Asteroids

NASA Astrophysics Data System (ADS)

Ezzedine, S. M.; Dearborn, D. S.; Miller, P. L.

2015-12-01

The annual probability of an asteroid impact is low, but over time, such catastrophic events are inevitable. Interest in assessing the impact consequences has led us to develop a physics-based framework to seamlessly simulate the event from entry to impact, including air and water shock propagation and wave generation. The non-linear effects are simulated using the hydrodynamics code GEODYN. As effects propagate outward, they become a wave source for the linear-elastic-wave propagation code, WPP/WWP. The GEODYN-WPP/WWP coupling is based on the structured adaptive-mesh-refinement infrastructure, SAMRAI, and has been used in FEMA table-top exercises conducted in 2013 and 2014, and more recently, the 2015 Planetary Defense Conference exercise. Results from these simulations provide an estimate of onshore effects and can inform more sophisticated inundation models. The capabilities of this methodology are illustrated by providing results for different impact locations, and an exploration of asteroid size on the waves arriving at the shoreline of area cities. We constructed the maximum and minimum envelops of water-wave heights given the size of the asteroid and the location of the impact along the risk corridor. Such profiles can inform emergency response and disaster-mitigation efforts, and may be used for design of maritime protection or assessment of risk to shoreline structures of interest. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-675390-DRAFT.

77 FR 5759 - Guarantee Fee Rates for Guaranteed Loans for Fiscal Year 2012; Maximum Portion of Guarantee...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-06

... impact business investment as defined in 7 CFR 4279.155(b)(5) and be located in rural communities that... experiencing trauma as a result of natural disaster, or that are experiencing fundamental structural changes in...

First-principles study of band gap engineering via oxygen vacancy doping in perovskite ABB'O₃ solid solutions

DOE PAGES

Qi, Tingting; Curnan, Matthew T.; Kim, Seungchul; ...

2011-12-15

Oxygen vacancies in perovskite oxide solid solutions are fundamentally interesting and technologically important. However, experimental characterization of the vacancy locations and their impact on electronic structure is challenging. We have carried out first-principles calculations on two Zr-modified solid solutions, Pb(Zn 1/3Nb 2/3)O₃ and Pb(Mg 1/3Nb 2/3)O₃, in which vacancies are present. We find that the vacancies are more likely to reside between low-valent cation-cation pairs than high-valent cation-cation pairs. Based on the analysis of our results, we formulate guidelines that can be used to predict the location of oxygen vacancies in perovskite solid solutions. Our results show that vacancies canmore » have a significant impact on both the conduction and valence band energies, in some cases lowering the band gap by ≈0.5 eV. The effects of vacancies on the electronic band structure can be understood within the framework of crystal field theory.« less

Fiber-Optic Micrometeoroid/Orbital Debris Impact Detector System

NASA Technical Reports Server (NTRS)

Christiansen, Eric L.; Tennyson, R. C.; Morison, W. D.

2012-01-01

A document describes a reliable, lightweight micrometeoroid/orbital debris (MMOD) detection system that can be located at strategic positions of "high consequence" to provide real-time warning of a penetration, its location, and the extent of the damage to a spacecraft. The concept is to employ fiber-optic sensors to detect impact damage and penetration of spacecraft structures. The fibers are non-electrical, employ light waves, and are immune to electromagnetic interference. The fiber-optic sensor array can be made as a stand-alone product, being bonded to a flexible membrane material or a structure that is employed as a MMOD shield material. The optical sensors can also be woven into hybrid MMOD shielding fabrics. The glass fibers of the fiber-optic sensor provide a dual purpose in contributing to the breakup of MMOD projectiles. The grid arrays can be made in a modular configuration to provide coverage over any area desired. Each module can be connected to a central scanner instrument and be interrogated in a continuous or periodic mode.

Physical property data from the ICDP-USGS Eyreville cores A and B, Chesapeake Bay impact structure, Virginia, USA, acquired using a multisensor core logger

USGS Publications Warehouse

Pierce, H.A.; Murray, J.B.

2009-01-01

The International Continental Scientific Drilling Program (ICDP) and the U.S. Geological Survey (USGS) drilled three core holes to a composite depth of 1766 m within the moat of the Chesapeake Bay impact structure. Core recovery rates from the drilling were high (??90%), but problems with core hole collapse limited the geophysical downhole logging to natural-gamma and temperature logs. To supplement the downhole logs, ??5% of the Chesapeake Bay impact structure cores was processed through the USGS GeoTek multisensor core logger (MSCL) located in Menlo Park, California. The measured physical properties included core thickness (cm), density (g cm-3), P-wave velocity (m s-1), P-wave amplitude (%), magnetic susceptibility (cgs), and resistivity (ohm-m). Fractional porosity was a secondary calculated property. The MSCL data-sampling interval for all core sections was 1 cm longitudinally. Photos of each MSCL sampled core section were imbedded with the physical property data for direct comparison. These data have been used in seismic, geologic, thermal history, magnetic, and gravity models of the Chesapeake Bay impact structure. Each physical property curve has a unique signature when viewed over the full depth of the Chesapeake Bay impact structure core holes. Variations in the measured properties reflect differences in pre-impact target-rock lithologies and spatial variations in impact-related deformation during late-stage crater collapse and ocean resurge. ?? 2009 The Geological Society of America.

Altered fish community and feeding behaviour in close proximity to boat moorings in an urban estuary.

PubMed

Lanham, Brendan S; Vergés, Adriana; Hedge, Luke H; Johnston, Emma L; Poore, Alistair G B

2018-04-01

Coastal urbanization has led to large-scale transformation of estuaries, with artificial structures now commonplace. Boat moorings are known to reduce seagrass cover, but little is known about their effect on fish communities. We used underwater video to quantify abundance, diversity, composition and feeding behaviour of fish assemblages on two scales: with increasing distance from moorings on fine scales, and among locations where moorings were present or absent. Fish were less abundant in close proximity to boat moorings, and the species composition varied on fine scales, leading to lower predation pressure near moorings. There was no relationship at the location with seagrass. On larger scales, we detected no differences in abundance or community composition among locations where moorings were present or absent. These findings show a clear impact of moorings on fish and highlight the importance of fine-scale assessments over location-scale comparisons in the detection of the effects of artificial structures. Copyright © 2018 Elsevier Ltd. All rights reserved.

Multi-Dimensional Damage Detection for Surfaces and Structures

NASA Technical Reports Server (NTRS)

Williams, Martha; Lewis, Mark; Roberson, Luke; Medelius, Pedro; Gibson, Tracy; Parks, Steen; Snyder, Sarah

2013-01-01

Current designs for inflatable or semi-rigidized structures for habitats and space applications use a multiple-layer construction, alternating thin layers with thicker, stronger layers, which produces a layered composite structure that is much better at resisting damage. Even though such composite structures or layered systems are robust, they can still be susceptible to penetration damage. The ability to detect damage to surfaces of inflatable or semi-rigid habitat structures is of great interest to NASA. Damage caused by impacts of foreign objects such as micrometeorites can rupture the shell of these structures, causing loss of critical hardware and/or the life of the crew. While not all impacts will have a catastrophic result, it will be very important to identify and locate areas of the exterior shell that have been damaged by impacts so that repairs (or other provisions) can be made to reduce the probability of shell wall rupture. This disclosure describes a system that will provide real-time data regarding the health of the inflatable shell or rigidized structures, and information related to the location and depth of impact damage. The innovation described here is a method of determining the size, location, and direction of damage in a multilayered structure. In the multi-dimensional damage detection system, layers of two-dimensional thin film detection layers are used to form a layered composite, with non-detection layers separating the detection layers. The non-detection layers may be either thicker or thinner than the detection layers. The thin-film damage detection layers are thin films of materials with a conductive grid or striped pattern. The conductive pattern may be applied by several methods, including printing, plating, sputtering, photolithography, and etching, and can include as many detection layers that are necessary for the structure construction or to afford the detection detail level required. The damage is detected using a detector or sensory system, which may include a time domain reflectometer, resistivity monitoring hardware, or other resistance-based systems. To begin, a layered composite consisting of thin-film damage detection layers separated by non-damage detection layers is fabricated. The damage detection layers are attached to a detector that provides details regarding the physical health of each detection layer individually. If damage occurs to any of the detection layers, a change in the electrical properties of the detection layers damaged occurs, and a response is generated. Real-time analysis of these responses will provide details regarding the depth, location, and size estimation of the damage. Multiple damages can be detected, and the extent (depth) of the damage can be used to generate prognostic information related to the expected lifetime of the layered composite system. The detection system can be fabricated very easily using off-the-shelf equipment, and the detection algorithms can be written and updated (as needed) to provide the level of detail needed based on the system being monitored. Connecting to the thin film detection layers is very easy as well. The truly unique feature of the system is its flexibility; the system can be designed to gather as much (or as little) information as the end user feels necessary. Individual detection layers can be turned on or off as necessary, and algorithms can be used to optimize performance. The system can be used to generate both diagnostic and prognostic information related to the health of layer composite structures, which will be essential if such systems are utilized for space exploration. The technology is also applicable to other in-situ health monitoring systems for structure integrity.

Global Evidence for an End-Permian Mass Extinction Event

NASA Astrophysics Data System (ADS)

Becker, L.; Nicholson, C.; Poreda, R.; Basu, A.; Acampo, A.

2003-04-01

We will present the global evidence for a Permian-Triassic impact event and re-examine some of the structural, seismic, gravity and well data for a proposed impact crater, the Bedout High, offshore northwestern Australia (Gorter, PESA News pp. 33--34, 1996). Gorter (1996) speculates that the Bedout High is the uplifted core (30 km) of a circular feature, some 220 km across, formed by the impact of a large bolide (comet or asteroid) with the earth near the end-Permian (K-Ar dating of volcanics ˜253 +/- 5 Ma). Accepting a possible impact origin for the Bedout structure, with the indicated dimensions, would have had profound effects on global climate and significant changes in lithotratigraphic, biostratigraphic and chemo-stratigraphic indicators as seen in several Permian-Triassic locations worldwide. Evidence for an impact of extraterrestrial origin is based upon several impact tracers including shocked metamorphosed grains, productivity collapse, helium-3, Mossbauer spectroscopy on nanophase Fe material, noble gases in magnetic fines and fullerenes with trapped noble gases from some end-Permian sites. These findings suggest that the Bedout structure and a possible newly discovered (˜100 km) secondary crater may be good candidates for an oceanic/continental impact(s) at the end Permian, triggering the most severe mass extinction in the history of life on the Earth.

Fine-Scale Ecological and Genetic Population Structure of Two Whitefish (Coregoninae) Species in the Vicinity of Industrial Thermal Emissions.

PubMed

Graham, Carly F; Eberts, Rebecca L; Morgan, Thomas D; Boreham, Douglas R; Lance, Stacey L; Manzon, Richard G; Martino, Jessica A; Rogers, Sean M; Wilson, Joanna Y; Somers, Christopher M

2016-01-01

Thermal pollution from industrial processes can have negative impacts on the spawning and development of cold-water fish. Point sources of thermal effluent may need to be managed to avoid affecting discrete populations. Correspondingly, we examined fine-scale ecological and genetic population structure of two whitefish species (Coregonus clupeaformis and Prosopium cylindraceum) on Lake Huron, Canada, in the immediate vicinity of thermal effluent from nuclear power generation. Niche metrics using δ13C and δ15N stable isotopes showed high levels of overlap (48.6 to 94.5%) in resource use by adult fish captured in areas affected by thermal effluent compared to nearby reference locations. Isotopic niche size, a metric of resource use diversity, was 1.3- to 2.8-fold higher than reference values in some thermally affected areas, indicative of fish mixing. Microsatellite analyses of genetic population structure (Fst, STRUCTURE and DAPC) indicated that fish captured at all locations in the vicinity of the power plant were part of a larger population extending beyond the study area. In concert, ecological and genetic markers do not support the presence of an evolutionarily significant unit in the vicinity of the power plant. Thus, future research should focus on the potential impacts of thermal emissions on development and recruitment.

Fine-Scale Ecological and Genetic Population Structure of Two Whitefish (Coregoninae) Species in the Vicinity of Industrial Thermal Emissions

PubMed Central

Graham, Carly F.; Eberts, Rebecca L.; Morgan, Thomas D.; Boreham, Douglas R.; Lance, Stacey L.; Manzon, Richard G.; Martino, Jessica A.; Rogers, Sean M.; Wilson, Joanna Y.; Somers, Christopher M.

2016-01-01

Thermal pollution from industrial processes can have negative impacts on the spawning and development of cold-water fish. Point sources of thermal effluent may need to be managed to avoid affecting discrete populations. Correspondingly, we examined fine-scale ecological and genetic population structure of two whitefish species (Coregonus clupeaformis and Prosopium cylindraceum) on Lake Huron, Canada, in the immediate vicinity of thermal effluent from nuclear power generation. Niche metrics using δ13C and δ15N stable isotopes showed high levels of overlap (48.6 to 94.5%) in resource use by adult fish captured in areas affected by thermal effluent compared to nearby reference locations. Isotopic niche size, a metric of resource use diversity, was 1.3- to 2.8-fold higher than reference values in some thermally affected areas, indicative of fish mixing. Microsatellite analyses of genetic population structure (Fst, STRUCTURE and DAPC) indicated that fish captured at all locations in the vicinity of the power plant were part of a larger population extending beyond the study area. In concert, ecological and genetic markers do not support the presence of an evolutionarily significant unit in the vicinity of the power plant. Thus, future research should focus on the potential impacts of thermal emissions on development and recruitment. PMID:26807722

Impact detection and analysis/health monitoring system for composites

NASA Astrophysics Data System (ADS)

Child, James E.; Kumar, Amrita; Beard, Shawn; Qing, Peter; Paslay, Don G.

2006-05-01

This manuscript includes information from test evaluations and development of a smart event detection system for use in monitoring composite rocket motor cases for damaging impacts. The primary purpose of the system as a sentry for case impact event logging is accomplished through; implementation of a passive network of miniaturized piezoelectric sensors, logger with pre-determined force threshold levels, and analysis software. Empirical approaches to structural characterizations and network calibrations along with implementation techniques were successfully evaluated, testing was performed on both unloaded (less propellants) as well as loaded rocket motors with the cylindrical areas being of primary focus. The logged test impact data with known physical network parameters provided for impact location as well as force determination, typically within 3 inches of actual impact location using a 4 foot network grid and force accuracy within 25%of an actual impact force. The simplistic empirical characterization approach along with the robust / flexible sensor grids and battery operated portable logger show promise of a system that can increase confidence in composite integrity for both new assets progressing through manufacturing processes as well as existing assets that may be in storage or transportation.

Experiments and 3D simulations of flow structures in junctions and their influence on location of flowmeters.

PubMed

Mignot, E; Bonakdari, H; Knothe, P; Lipeme Kouyi, G; Bessette, A; Rivière, N; Bertrand-Krajewski, J-L

2012-01-01

Open-channel junctions are common occurrences in sewer networks and flow rate measurement often occurs near these singularities. Local flow structures are 3D, impact on the representativeness of the local flow measurements and thus lead to deviations in the flow rate estimation. The present study aims (i) to measure and simulate the flow pattern in a junction flow, (ii) to analyse the impact of the junction on the velocity distribution according to the distance from the junction and thus (iii) to evaluate the typical error derived from the computation of the flow rate close to the junction.

Geophysical signatures and modeling results from a buried impact structure in Decorah, Iowa, USA

NASA Astrophysics Data System (ADS)

Kass, A.; Bedrosian, P.; Drenth, B.; Bloss, B. R.; McKay, R.; Liu, H. P.; French, B.; Witzke, B.

2013-12-01

The Decorah Impact Structure is a probable buried impact crater of Middle Ordovician age located in Northeast Iowa, USA. Originally hypothesized by the Iowa Geological and Water Survey though identification of a unique shale layer and shocked quartz from borehole samples, the 5.5 km diameter structure is nearly completely concealed beneath the town of Decorah, Iowa and the surrounding area. In late 2012 and early 2013, the US Geological Survey conducted airborne geophysical studies in the area to investigate structures and potential mineral resources associated with the 1.1 Ga Midcontinent Rift system. Full-tensor gravity gradiometry and airborne transient electromagnetic surveys were flown to investigate basement geometry and composition, as well as to map out the thick package of Phanerozoic sediments blanketing the region. Multiple survey lines intersected the impact structure, which was clearly visible in both the electromagnetic and gravity datasets. The electromagnetic data, acquired with a VTEM system from Geotech, Ltd., identified and mapped the post-impact Winneshiek Shale, which is present only in the crater (having been eroded everywhere else within the survey area). The resulting 5.5 km diameter circular conductor aligned nearly perfectly with the structure inferred by the Iowa Geological and Water Survey. The airborne full-tensor gravity gradient data, collected by Bell Geospace, clearly demarcates a density low in each component consistent with the center of the impact structure. The conductivity and density of some of the stratigraphic units both within as well as outside the impact structure were measured from core samples, and used to inform the modeling and inversion approaches. Both the electromagnetic data and the gravity gradiometry data underwent an extensive modeling and inversion procedure to investigate the geometry of the impact structure in three dimensions. From these results, we present a three dimensional model of the proposed Decorah Impact Structure and surrounding area. Not only will this model improve an understanding of the geology and hydrology of the region, but also will allow for more precise estimations of the energy and size of the impacting body. Any use of trade names is for descriptive purposes only and does not imply endorsement by the U.S. Government.

Seismo-Acoustic Numerical Investigation of Land Impacts, Water Impacts, or Air Bursts of Asteroids

NASA Astrophysics Data System (ADS)

Ezzedine, S. M.; Miller, P. L.; Dearborn, D. S.

2016-12-01

The annual probability of an asteroid impact is low, but over time, such catastrophic events are inevitable. Interest in assessing the impact consequences has led us to develop a physics-based framework to seamlessly simulate the event from entry to impact, including air, water and ground shock propagation and wave generation. The non-linear effects are simulated using the hydrodynamics code GEODYN. As effects propagate outward, they become a wave source for the linear-elastic-wave propagation code and simulated using SAW or SWWP, depends on whether the asteroid impacts the land or the ocean, respectively. The GEODYN-SAW-SWWP coupling is based on the structured adaptive-mesh-refinement infrastructure, SAMRAI, and has been used in FEMA table-top exercises conducted in 2013 and 2014, and more recently, the 2015 Planetary Defense Conference exercise. Moreover, during atmospheric entry, asteroids create an acoustic trace that could be used to infer several physical characteristics of asteroid itself. Using SAW we explore the physical space parameters in order to rank the most important characteristics; Results from these simulations provide an estimate of onshore and offshore effects and can inform more sophisticated inundation and structural models. The capabilities of this methodology are illustrated by providing results for different impact locations, and an exploration of asteroid size on the waves arriving at the shoreline of area cities. We constructed the maximum and minimum envelops of water-wave heights or acceleration spectra given the size of the asteroid and the location of the impact along the risk corridor. Such profiles can inform emergency response and disaster-mitigation efforts. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Seismo-Acoustic Numerical Investigation of Land Impacts, Water Impacts, or Air Bursts of Asteroids

NASA Astrophysics Data System (ADS)

Ezzedine, S. M.; Dearborn, D. S.; Miller, P. L.

2017-12-01

The annual probability of an asteroid impact is low, but over time, such catastrophic events are inevitable. Interest in assessing the impact consequences has led us to develop a physics-based framework to seamlessly simulate the event from entry to impact, including air, water and ground shock propagation and wave generation. The non-linear effects are simulated using the hydrodynamics code GEODYN. As effects propagate outward, they become a wave source for the linear-elastic-wave propagation code and simulated using SAW or SWWP, depends on whether the asteroid impacts the land or the ocean, respectively. The GEODYN-SAW-SWWP coupling is based on the structured adaptive-mesh-refinement infrastructure, SAMRAI, and has been used in FEMA table-top exercises conducted in 2013 and 2014, and more recently, the 2015 Planetary Defense Conference exercise. Moreover, during atmospheric entry, asteroids create an acoustic trace that could be used to infer several physical characteristics of asteroid itself. Using SAW we explore the physical space parameters in order to rank the most important characteristics; Results from these simulations provide an estimate of onshore and offshore effects and can inform more sophisticated inundation and structural models. The capabilities of this methodology are illustrated by providing results for different impact locations, and an exploration of asteroid size on the waves arriving at the shoreline of area cities. We constructed the maximum and minimum envelops of water-wave heights or acceleration spectra given the size of the asteroid and the location of the impact along the risk corridor. Such profiles can inform emergency response and disaster-mitigation efforts. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

The Influence of Model Complexity on the Impact Response of a Shuttle Leading-Edge Panel Finite Element Simulation

NASA Technical Reports Server (NTRS)

Jones, Lisa E. (Technical Monitor); Stockwell, Alan E.

2005-01-01

LS-DYNA simulations were conducted to study the influence of model complexity on the response of a typical Reinforced Carbon-Carbon (RCC) panel to a foam impact at a location approximately midway between the ribs. A structural model comprised of Panels 10, 11, and TSeal 11 was chosen as the baseline model for the study. A simulation was conducted with foam striking Panel 10 at Location 4 at an alpha angle of 10 degrees, with an impact velocity of 1000 ft/sec. A second simulation was conducted after removing Panel 11 from the model, and a third simulation was conducted after removing both Panel 11 and T-Seal 11. All three simulations showed approximately the same response for Panel 10, and the simplified simulation model containing only Panel 10 was shown to be significantly less expensive to execute than the other two more complex models.

Aerogel Track Morphology: Measurement, Three Dimensional Reconstruction and Particle Location using Confocal Laser Scanning Microscopy

NASA Technical Reports Server (NTRS)

Kearsley, A. T.; Ball, A. D.; Wozniakiewicz, P. A.; Graham, G. A.; Burchell, M. J.; Cole, M. J.; Horz, F.; See, T. H.

2007-01-01

The Stardust spacecraft returned the first undoubted samples of cometary dust, with many grains embedded in the silica aerogel collector . Although many tracks contain one or more large terminal particles of a wide range of mineral compositions , there is also abundant material along the track walls. To help interpret the full particle size, structure and mass, both experimental simulation of impact by shots and numerical modeling of the impact process have been attempted. However, all approaches require accurate and precise measurement of impact track size parameters such as length, width and volume of specific portions. To make such measurements is not easy, especially if extensive aerogel fracturing and discoloration has occurred. In this paper we describe the application and limitations of laser confocal imagery for determination of aerogel track parameters, and for the location of particle remains.

77 FR 802 - Environmental Documents Prepared for Oil, Gas, and Mineral Operations by the Gulf of Mexico Outer...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-06

... Assessments (SEA) and Findings of No Significant Impact (FONSI). These EA's were prepared during the period..., Block 28, 9/26/2011 Structure Removal, SEA ES/SR Lease OCS 00353 & 11-230 & 11-236. 00694, located 4-5...

Meteoroid and debris special investigation group data acquisition procedures

NASA Technical Reports Server (NTRS)

See, Thomas H.; Allbrooks, Martha K.; Atkinson, Dale R.; Sapp, Clyde A.; Simon, Charles G.; Zolensky, Mike E.

1992-01-01

The entire LDEF spacecraft was examined by M&D SIG for impact (i.e., craters greater than or = 0.5 mm and penetrations greater than or = 0.3 mm in diameter) and related features (e.g., debris, secondaries). During the various detailed surveys conducted at NASA Kennedy, approx. 5,000 impact related features were photodocumented, and their locations measured and recorded; an additional approx. 30,000 smaller features were counted. The equipment and techniques used by the M&D SIG permitted the determination and recording of the locations and diameters of the 5,000 imaged features. A variety of experimental and LDEF structural hardware was acquired by the M&D SIG and is presently being examined and curated at NASA Johnson.

LRO Finds Apollo 16 Booster Rocket Impact Site

NASA Image and Video Library

2017-12-08

After decades of uncertainty, the Apollo 16 S-IVB impact site on the lunar surface has been identified. S-IVBs were portions of the Saturn V rockets that brought astronauts to the moon. The site was identified in imagery from the high-resolution LROC Narrow Angle Camera aboard NASA's Lunar Reconnaissance Orbiter. Beginning with Apollo 13, the S-IVB rocket stages were deliberately impacted on the lunar surface after they were used. Seismometers placed on the moon by earlier Apollo astronauts measured the energy of these impacts to shed light on the internal lunar structure. Locations of the craters that the boosters left behind were estimated from tracking data collected just prior to the impacts. Earlier in the LRO mission, the Apollo 13, 14, 15 and 17 impact sites were successfully identified, but Apollo 16's remained elusive. In the case of Apollo 16, radio contact with the booster was lost before the impact, so the location was only poorly known. Positive identification of the Apollo 16 S-IVB site took more time than the other four impact craters because the location ended up differing by about 30 km (about 19 miles) from the Apollo-era tracking estimate. (For comparison, the other four S-IVB craters were all within 7 km -- about four miles -- of their estimated locations.) Apollo 16's S-IVB stage is on Mare Insularum, about 160 miles southwest of Copernicus Crater (more precisely: 1.921 degrees north, 335.377 degrees east, minus 1,104 meters elevation). Credit: NASA/Goddard/Arizona State University NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

iPHLoc-ES: Identification of bacteriophage protein locations using evolutionary and structural features.

PubMed

Shatabda, Swakkhar; Saha, Sanjay; Sharma, Alok; Dehzangi, Abdollah

2017-12-21

Bacteriophage proteins are viruses that can significantly impact on the functioning of bacteria and can be used in phage based therapy. The functioning of Bacteriophage in the host bacteria depends on its location in those host cells. It is very important to know the subcellular location of the phage proteins in a host cell in order to understand their working mechanism. In this paper, we propose iPHLoc-ES, a prediction method for subcellular localization of bacteriophage proteins. We aim to solve two problems: discriminating between host located and non-host located phage proteins and discriminating between the locations of host located protein in a host cell (membrane or cytoplasm). To do this, we extract sets of evolutionary and structural features of phage protein and employ Support Vector Machine (SVM) as our classifier. We also use recursive feature elimination (RFE) to reduce the number of features for effective prediction. On standard dataset using standard evaluation criteria, our method significantly outperforms the state-of-the-art predictor. iPHLoc-ES is readily available to use as a standalone tool from: https://github.com/swakkhar/iPHLoc-ES/ and as a web application from: http://brl.uiu.ac.bd/iPHLoc-ES/. Copyright © 2017 Elsevier Ltd. All rights reserved.

Some Basics for Teaching and Evaluating Energy Conservation in the Home

ERIC Educational Resources Information Center

McColl, Robert W.

1978-01-01

Examines methods for determining thermal efficiency and measuring heat loss in the home. Suggests ways to conserve energy based upon (1) climatic environment and its impact on a structure, (2) physical location of buildings and their microclimate, and (3) behavior modification of the inhabitants. (Author)

Structural identification of triacylglycerol isomers using electron impact excitation of ions from organics (EIEIO).

PubMed

Baba, Takashi; Campbell, J Larry; Le Blanc, J C Yves; Baker, Paul R S

2016-11-01

Electron-induced dissociation or electron impact excitation of ions from organics (EIEIO) was applied to triacylglycerols (TAGs) for in-depth molecular structure analysis using MS. In EIEIO, energetic electrons (∼10 eV) fragmented TAG ions to allow for regioisomeric assignment of identified acyl groups at the sn-2 or sn-1/3 positions of the glycerol backbone. In addition, carbon-carbon double bond locations within the acyl chains could also be assigned by EIEIO. Beyond the analysis of lipid standards, this technique was applied to edible oils and natural lipid extracts to demonstrate the power of this method to provide in-depth structural elucidation of TAG molecular species. Copyright © 2016 by the American Society for Biochemistry and Molecular Biology, Inc.

Development of lightweight structural health monitoring systems for aerospace applications

NASA Astrophysics Data System (ADS)

Pearson, Matthew

This thesis investigates the development of structural health monitoring systems (SHM) for aerospace applications. The work focuses on each aspect of a SHM system covering novel transducer technologies and damage detection techniques to detect and locate damage in metallic and composite structures. Secondly the potential of energy harvesting and power arrangement methodologies to provide a stable power source is assessed. Finally culminating in the realisation of smart SHM structures. 1. Transducer Technology A thorough experimental study of low profile, low weight novel transducers not normally used for acoustic emission (AE) and acousto-ultrasonics (AU) damage detection was conducted. This included assessment of their performance when exposed to aircraft environments and feasibility of embedding these transducers in composites specimens in order to realise smart structures. 2. Damage Detection An extensive experimental programme into damage detection utilising AE and AU were conducted in both composites and metallic structures. These techniques were used to assess different damage mechanism within these materials. The same transducers were used for novel AE location techniques coupled with AU similarity assessment to successfully detect and locate damage in a variety of structures. 3. Energy Harvesting and Power Management Experimental investigations and numerical simulations were undertaken to assess the power generation levels of piezoelectric and thermoelectric generators for typical vibration and temperature differentials which exist in the aerospace environment. Furthermore a power management system was assessed to demonstrate the ability of the system to take the varying nature of the input power and condition it to a stable power source for a system. 4. Smart Structures The research conducted is brought together into a smart carbon fibre wing showcasing the novel embedded transducers for AE and AU damage detection and location, as well as vibration energy harvesting. A study into impact damage detection using the techniques showed the successful detection and location of damage. Also the feasibility of the embedded transducers for power generation was assessed..

Al Umchaimin depression, Western Iraq: An impact structure?

NASA Astrophysics Data System (ADS)

Underwood, James R., Jr.

Al Umchaimin, in Arabic 'hiding place' or 'place of ambush', is located at latitude 32 degrees 35.5 N and longitude 39 degrees 25 E. The nearly circular depression averages 2.75 km in diameter and is 33-42 m deep. It is floored with fine-grained, clay-rich deposits, estimated to be 36 m thick, the surface of which shows well-developed desiccation fissures or mudcracks when dry. Because of its nearly circular planimetric shape and its apparent isolation from other surface and subsurface features, it has been considered by some to be a possible meteorite impact structure and by others to be a surface collapse feature that originated following removal of magma from the subsurface as the magma extruded elsewhere. Al Umchaimin was listed in the U.S. Geological Survey tabulation of 110 structures worldwide for which a meteorite impact origin had been suggested. It was placed in Category 6 Structures for which more data are required for classification. It is concluded that, on the basis of the studies that have been made of Al Umchaimin and on the basis of the brief site visit made, Al Umchaimin probably is not an impact structure but most likely resulted from the enlargement and coalescence of sink holes and eventual collapse of the roof material into the resulting cavity.

Al Umchaimin depression, Western Iraq: An impact structure?

NASA Technical Reports Server (NTRS)

Underwood, James R., Jr.

1992-01-01

Al Umchaimin, in Arabic 'hiding place' or 'place of ambush', is located at latitude 32 degrees 35.5 N and longitude 39 degrees 25 E. The nearly circular depression averages 2.75 km in diameter and is 33-42 m deep. It is floored with fine-grained, clay-rich deposits, estimated to be 36 m thick, the surface of which shows well-developed desiccation fissures or mudcracks when dry. Because of its nearly circular planimetric shape and its apparent isolation from other surface and subsurface features, it has been considered by some to be a possible meteorite impact structure and by others to be a surface collapse feature that originated following removal of magma from the subsurface as the magma extruded elsewhere. Al Umchaimin was listed in the U.S. Geological Survey tabulation of 110 structures worldwide for which a meteorite impact origin had been suggested. It was placed in Category 6 Structures for which more data are required for classification. It is concluded that, on the basis of the studies that have been made of Al Umchaimin and on the basis of the brief site visit made, Al Umchaimin probably is not an impact structure but most likely resulted from the enlargement and coalescence of sink holes and eventual collapse of the roof material into the resulting cavity.

Dynamic Finite Element Predictions for Mars Sample Return Cellular Impact Test #4

NASA Technical Reports Server (NTRS)

Fasanella, Edwin L.; Billings, Marcus D.

2001-01-01

The nonlinear finite element program MSC.Dytran was used to predict the impact pulse for (he drop test of an energy absorbing cellular structure. This pre-test simulation was performed to aid in the design of an energy absorbing concept for a highly reliable passive Earth Entry Vehicle (EEV) that will directly impact the Earth without a parachute. In addition, a goal of the simulation was to bound the acceleration pulse produced and delivered to the simulated space cargo container. EEV's are designed to return materials from asteroids, comets, or planets for laboratory analysis on Earth. The EEV concept uses an energy absorbing cellular structure designed to contain and limit the acceleration of space exploration samples during Earth impact. The spherical shaped cellular structure is composed of solid hexagonal and pentagonal foam-filled cells with hybrid graphite-epoxy/Kevlar cell walls. Space samples fit inside a smaller sphere at the enter of the EEV's cellular structure. The material models and failure criteria were varied to determine their effect on the resulting acceleration pulse. Pre-test analytical predictions using MSC.Dytran were compared with the test results obtained from impact test #4 using bungee accelerator located at the NASA Langley Research Center Impact Dynamics Research Facility. The material model used to represent the foam and the proper failure criteria for the cell walls were critical in predicting the impact loads of the cellular structure. It was determined that a FOAMI model for the foam and a 20% failure strain criteria for the cell walls gave an accurate prediction of the acceleration pulse for drop test #4.

Landscaping the structures of GAVI country vaccine supply chains and testing the effects of radical redesign.

PubMed

Lee, Bruce Y; Connor, Diana L; Wateska, Angela R; Norman, Bryan A; Rajgopal, Jayant; Cakouros, Brigid E; Chen, Sheng-I; Claypool, Erin G; Haidari, Leila A; Karir, Veena; Leonard, Jim; Mueller, Leslie E; Paul, Proma; Schmitz, Michelle M; Welling, Joel S; Weng, Yu-Ting; Brown, Shawn T

2015-08-26

Many of the world's vaccine supply chains do not adequately provide vaccines, prompting several questions: how are vaccine supply chains currently structured, are these structures closely tailored to individual countries, and should these supply chains be radically redesigned? We segmented the 57 GAVI-eligible countries' vaccine supply chains based on their structure/morphology, analyzed whether these segments correlated with differences in country characteristics, and then utilized HERMES to develop a detailed simulation model of three sample countries' supply chains and explore the cost and impact of various alternative structures. The majority of supply chains (34 of 57) consist of four levels, despite serving a wide diversity of geographical areas and population sizes. These four-level supply chains loosely fall into three clusters [(1) 18 countries relatively more bottom-heavy, i.e., many more storage locations lower in the supply chain, (2) seven with relatively more storage locations in both top and lower levels, and (3) nine comparatively more top-heavy] which do not correlate closely with any of the country characteristics considered. For all three cluster types, our HERMES modeling found that simplified systems (a central location shipping directly to immunization locations with a limited number of Hubs in between) resulted in lower operating costs. A standard four-tier design template may have been followed for most countries and raises the possibility that simpler and more tailored designs may be warranted. Copyright © 2015 Elsevier Ltd. All rights reserved.

TOPICAL REVIEW: Smart aggregates: multi-functional sensors for concrete structures—a tutorial and a review

NASA Astrophysics Data System (ADS)

Song, Gangbing; Gu, Haichang; Mo, Yi-Lung

2008-06-01

This paper summarizes the authors' recent pioneering research work in piezoceramic-based smart aggregates and their innovative applications in concrete civil structures. The basic operating principle of smart aggregates is first introduced. The proposed smart aggregate is formed by embedding a waterproof piezoelectric patch with lead wires into a small concrete block. The proposed smart aggregates are multi-functional and can perform three major tasks: early-age concrete strength monitoring, impact detection and structural health monitoring. The proposed smart aggregates are embedded into the desired location before the casting of the concrete structure. The concrete strength development is monitored by observing the high frequency harmonic wave response of the smart aggregate. Impact on the concrete structure is detected by observing the open-circuit voltage of the piezoceramic patch in the smart aggregate. For structural health monitoring purposes, a smart aggregate-based active sensing system is designed for the concrete structure. Wavelet packet analysis is used as a signal-processing tool to analyze the sensor signal. A damage index based on the wavelet packet analysis is used to determine the structural health status. To better describe the time-history and location information of damage, two types of damage index matrices are proposed: a sensor-history damage index matrix and an actuator-sensor damage index matrix. To demonstrate the multi-functionality of the proposed smart aggregates, different types of concrete structures have been used as test objects, including concrete bridge bent-caps, concrete cylinders and a concrete frame. Experimental results have verified the effectiveness and the multi-functionality of the proposed smart aggregates. The multi-functional smart aggregates have the potential to be applied to the comprehensive monitoring of concrete structures from their earliest stages and throughout their lifetime.

Cratering in glasses impacted by debris or micrometeorites

NASA Technical Reports Server (NTRS)

Wiedlocher, David E.; Kinser, Donald L.

1993-01-01

Mechanical strength measurements on five glasses and one glass-ceramic exposed on LDEF revealed no damage exceeding experimental limits of error. The measurement technique subjected less than 5 percent of the sample surface area to stresses above 90 percent of the failure strength. Seven micrometeorite or space debris impacts occurred at locations which were not in that portion of the sample subjected to greater than 90 percent of the applied stress. As a result of this, the impact events on the sample were not detected in the mechanical strength measurements. The physical form and structure of the impact sites was carefully examined to determine the influence of those events upon stress concentration associated with the impact and the resulting mechanical strength. The size of the impact site, insofar as it determines flaw size for fracture purposes, was examined. Surface topography of the impacts reveals that six of the seven sites display impact melting. The classical melt crater structure is surrounded by a zone of fractured glass. Residual stresses arising from shock compression and from cooling of the fused zone cannot be included in the fracture mechanics analyses based on simple flaw size measurements. Strategies for refining estimates of mechanical strength degradation by impact events are presented.

Nondestructive Structural Damage Detection in Flexible Space Structures Using Vibration Characterization

NASA Technical Reports Server (NTRS)

Ricles, James M.

1991-01-01

Spacecraft are susceptible to structural damage over their operating life from impact, environmental loads, and fatigue. Structural damage that is not detected and not corrected may potentially cause more damage and eventually catastrophic structural failure. NASA's current fleet of reusable spacecraft, namely the Space Shuttle, has been flown on several missions. In addition, configurations of future NASA space structures, e.g. Space Station Freedom, are larger and more complex than current structures, making them more susceptible to damage as well as being more difficult to inspect. Consequently, a reliable structural damage detection capability is essential to maintain the flight safety of these structures. Visual inspections alone can not locate impending material failure (fatigue cracks, yielding); it can only observe post-failure situations. An alternative approach is to develop an inspection and monitoring system based on vibration characterization that assesses the integrity of structural and mechanical components. A methodology for detecting structural damage is presented. This methodology is based on utilizing modal test data in conjunction with a correlated analytical model of the structure to: (1) identify the structural dynamic characteristics (resonant frequencies and mode shapes) from measurements of ambient motions and/or force excitation; (2) calculate modal residual force vectors to identify the location of structural damage; and (3) conduct a weighted sensitivity analysis in order to assess the extent of mass and stiffness variations, where structural damage is characterized by stiffness reductions. The approach is unique from other existing approaches in that varying system mass and stiffness, mass center locations, the perturbation of both the natural frequencies and mode shapes, and statistical confidence factors for structural parameters and experimental instrumentation are all accounted for directly.

Analysis of the vibration environment induced on spacecraft components by hypervelocity impact

NASA Astrophysics Data System (ADS)

Pavarin, Daniele

2009-06-01

This paper reports the result achieved within the study ``Spacecraft Disturbances from Hypervelocity Impact'', performed by CISAS and Thales-Alenia Space Italia under European Space Agency contract. The research project investigated the perturbations produced on spacecraft internal components as a consequence of hypervelocity impacts of micrometeoroids and orbital debris on the external walls of the vehicle. Objective of the study was: (i) to set-up a general numerical /experimental procedure to investigate the vibration induced by hypervelocity impact, (ii) to analyze the GOCE mission in order to asses whether the vibration environment induce by the impact of orbital debris and micrometeoroids could jeopardize the mission. The research project was conducted both experimentally and numerically, performing a large number of impact tests on GOCE-like structural configurations and extrapolating the experimental results via numerical simulations based on hydrocode calculations, finite element and statistical energy analysis. As a result, a database was established which correlates the impact conditions in the experimental range (0.6 to 2.3 mm projectiles at 2.5 to 5 km/s) with the shock spectra on selected locations on various types of structural models.The main out coming of the study are: (i) a wide database reporting acceleration values on a wide range of impact condition, (ii) a general numerical methodology to investigate disturbances induced by space debris and micrometeoroids on general satellite structures.

Impact-Induced Clay Mineral Formation and Distribution on Mars

NASA Technical Reports Server (NTRS)

Rivera-Valentin, E. G.; Craig, P. I.

2015-01-01

Clay minerals have been identified in the central peaks and ejecta blankets of impact craters on Mars. Several studies have suggested these clay minerals formed as a result of impact induced hydrothermalism either during Mars' Noachian era or more recently by the melting of subsurface ice. Examples of post-impact clay formation is found in several locations on Earth such as the Mjolnir and Woodleigh Impact Structures. Additionally, a recent study has suggested the clay minerals observed on Ceres are the result of impact-induced hydrothermal processes. Such processes may have occurred on Mars, possibly during the Noachian. Distinguishing between clay minerals formed preor post-impact can be accomplished by studying their IR spectra. In fact, showed that the IR spectra of clay minerals is greatly affected at longer wavelengths (i.e. mid-IR, 5-25 micron) by impact-induced shock deformation while the near-IR spectra (1.0-2.5 micron) remains relatively unchanged. This explains the discrepancy between NIR and MIR observations of clay minerals in martian impact craters noted. Thus, it allows us to determine whether a clay mineral formed from impact-induced hydrothermalism or were pre-existing and were altered by the impact. Here we study the role of impacts on the formation and distribution of clay minerals on Mars via a fully 3-D Monte Carlo cratering model, including impact- melt production using results from modern hydrocode simulations. We identify regions that are conducive to clay formation and the location of clay minerals post-bombardment.

Impact of Inflow Conditions on Coherent Structures in an Aneurysm

NASA Astrophysics Data System (ADS)

Yu, Paulo; Durgesh, Vibhav; Johari, Hamid

2017-11-01

An aneurysm is an enlargement of a weakened arterial wall that can be debilitating or fatal on rupture. Studies have shown that hemodynamics is integral to developing an understanding of aneurysm formation, growth, and rupture. This investigation focuses on a comprehensive study of the impact of varying inflow conditions and aneurysm shapes on spatial and temporal behavior of flow parameters and structures in an aneurysm. Two different shapes of an idealized rigid aneurysm model were studied and the non-dimensional frequency and Reynolds number were varied between 2-5 and 50-250, respectively. A ViVitro Labs SuperPump system was used to precisely control inflow conditions. Particle Image Velocimetry (PIV) measurements were performed at three different locations inside the aneurysm sac to obtain detailed velocity flow field information. The results of this study showed that aneurysm morphology significantly impacts spatial and temporal behavior of large-scale flow structures as well as wall shear stress distribution. The flow behavior and structures showed a significant difference with change in inflow conditions. A primary fluctuating flow structure was observed for Reynolds number of 50, while for higher Reynolds numbers, primary and secondary flow structures were observed. Furthermore, the paths of these coherent structures were dependent on aneurysm shape and inflow parameters.

Geohistorical records indicate no impact of the Deepwater Horizon oil spill on oyster body size

PubMed Central

Durham, Stephen R.

2016-01-01

Documentation of the near- and long-term effects of the Deepwater Horizon (DWH) oil spill, one of the largest environmental disasters in US history, is still ongoing. We used a novel before-after-control-impact analysis to test the hypothesis that average body size of intertidal populations of the eastern oyster (Crassostrea virginica) inhabiting impacted areas in Louisiana decreased due to increased stress/mortality related to the oil spill. Time-averaged death assemblages of oysters were used to establish a pre-spill baseline of body-size structure for four impacted and four control locations along a 350 km stretch of Louisiana's coastline. Post-spill body sizes were then measured from live oysters at each site in order to evaluate the differences in body size between oiled (i.e. impact) and unoiled (i.e. control) locations before and after the spill. Our results indicate that average body size of oysters remained relatively unchanged after the oil spill. There were also no temporal patterns in temperature, salinity or disease prevalence that could have explained our results. Together, these findings suggest that oysters either recovered rapidly following the immediate impact of the DWH oil spill, or that its impact was not severe enough to influence short-term population dynamics of the oyster beds. PMID:28018663

Impact-generated endolithic habitat within crystalline rocks of the Haughton impact structure, Devon Island, Canada.

PubMed

Pontefract, Alexandra; Osinski, Gordon R; Cockell, Charles S; Moore, Casey A; Moores, John E; Southam, Gordon

2014-06-01

The colonization of rocks by endolithic communities is an advantageous trait, especially in environments such as hot or cold deserts, where large temperature ranges, low water availability, and high-intensity ultraviolet radiation pose a significant challenge to survival and growth. On Mars, similar conditions (albeit more extreme) prevail. In these environments, meteorite impact structures could provide refuge for endolithic organisms. Though initially detrimental to biology, an impact event into a rocky body can favorably change the availability and habitability of a substrate for endolithic organisms, which are then able to (re)colonize microfractures and pore spaces created during the impact. Here, we show how shocked gneisses from the Haughton impact structure, Devon Island, Canada, offer significant refuge for endolithic communities. A total of 28 gneiss samples representing a range of shock states were analyzed, collected from in situ, stable field locations. For each sample, the top centimeter of rock was examined with confocal scanning laser microscopy, scanning electron microscopy, and bright-field microscopy to investigate the relationship of biomass with shock level, which was found to correlate generally with increased shock state and particularly with increased porosity. We found that gneisses, which experienced pressures between 35 and 60 GPa, provide the most ideal habitat for endolithic organisms.

Fine-scale ecological and genetic population structure of two whitefish (Coregoninae) species in the vicinity of industrial thermal emissions

DOE PAGES

Graham, Carly F.; Eberts, Rebecca L.; Morgan, Thomas D.; ...

2016-01-25

Thermal pollution from industrial processes can have negative impacts on the spawning and development of cold-water fish. Point sources of thermal effluent may need to be managed to avoid affecting discrete populations. Correspondingly, we examined fine-scale ecological and genetic population structure of two whitefish species ( Coregonus clupeaformis and Prosopium cylindraceum) on Lake Huron, Canada, in the immediate vicinity of thermal effluent from nuclear power generation. Niche metrics using δ 13C and δ 15N stable isotopes showed high levels of overlap (48.6 to 94.5%) in resource use by adult fish captured in areas affected by thermal effluent compared to nearbymore » reference locations. Isotopic niche size, a metric of resource use diversity, was 1.3- to 2.8-fold higher than reference values in some thermally affected areas, indicative of fish mixing. Microsatellite analyses of genetic population structure (F st, STRUCTURE and DAPC) indicated that fish captured at all locations in the vicinity of the power plant were part of a larger population extending beyond the study area. In concert, ecological and genetic markers do not support the presence of an evolutionarily significant unit in the vicinity of the power plant. Furthermore, future research should focus on the potential impacts of thermal emissions on development and recruitment.« less

Fine-scale ecological and genetic population structure of two whitefish (Coregoninae) species in the vicinity of industrial thermal emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Graham, Carly F.; Eberts, Rebecca L.; Morgan, Thomas D.

Thermal pollution from industrial processes can have negative impacts on the spawning and development of cold-water fish. Point sources of thermal effluent may need to be managed to avoid affecting discrete populations. Correspondingly, we examined fine-scale ecological and genetic population structure of two whitefish species ( Coregonus clupeaformis and Prosopium cylindraceum) on Lake Huron, Canada, in the immediate vicinity of thermal effluent from nuclear power generation. Niche metrics using δ 13C and δ 15N stable isotopes showed high levels of overlap (48.6 to 94.5%) in resource use by adult fish captured in areas affected by thermal effluent compared to nearbymore » reference locations. Isotopic niche size, a metric of resource use diversity, was 1.3- to 2.8-fold higher than reference values in some thermally affected areas, indicative of fish mixing. Microsatellite analyses of genetic population structure (F st, STRUCTURE and DAPC) indicated that fish captured at all locations in the vicinity of the power plant were part of a larger population extending beyond the study area. In concert, ecological and genetic markers do not support the presence of an evolutionarily significant unit in the vicinity of the power plant. Furthermore, future research should focus on the potential impacts of thermal emissions on development and recruitment.« less

Wind seismic noise introduced by external infrastructure: field data and transfer mechanism

NASA Astrophysics Data System (ADS)

Martysevich, Pavel; Starovoyt, Yuri

2017-04-01

Background seismic noise generated by wind was analyzed at six co-located seismic and infrasound arrays with the use of the wind speed data. The main factors affecting the noise level were identified as (a) external structures as antenna towers for intrasite communication, vegetation and heavy solar panels fixtures, (b) borehole casing and (c) local lithology. The wind-induced seismic noise peaks in the spectra can be predicted by combination of inverted pendulum model for antenna towers and structures used to support solar panels, free- or clamped-tube resonance of the borehole casing and is dependent on the type of sedimentary upper layer. Observed resonance frequencies are in agreement with calculated clamped / free tube modes for towers and borehole casings. Improvement of the seismic data quality can be achieved by minimizing the impact of surrounding structures close to seismic boreholes. The need and the advantage of the borehole installation may vanish and appear to be even not necessary at locations with non-consolidated sediments because the impact of surrounding structures on seismic background may significantly deteriorate the installation quality and therefore the detection capability of the array. Several IMS arrays where the radio telemetry antennas are used for data delivery to the central site may benefit from the redesign of the intrasite communication system by its substitute with the fiber-optic net as less harmful engineering solution.

Impact-Locator Sensor Panels

NASA Technical Reports Server (NTRS)

Christiansen, Eric L.; Byers, Terry; Gibbons, Frank

2008-01-01

Electronic sensor systems for detecting and locating impacts of rapidly moving particles on spacecraft have been invented. Systems of this type could also be useful on Earth in settings in which the occurrence of impacts and/or the locations of impacts are not immediately obvious and there are requirements to detect and quickly locate impacts to prevent or minimize damage.

Does Participation in Extracurricular Activities Impact Student Achievement?

ERIC Educational Resources Information Center

Abruzzo, Kristen J.; Lenis, Cristina; Romero, Yansi V.; Maser, Kevin J.; Morote, Elsa-Sofia

2016-01-01

This study was conducted in two high schools located in suburban, Long Island, New York, with a predominantly white population. The respondents in this study consisted of 234, 11th grade students. The data was analyzed using the structural equation model. Findings show that there is a positive correlation between percent of participation in…

39 CFR 776.6 - Design requirements for construction.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 39 Postal Service 1 2011-07-01 2011-07-01 false Design requirements for construction. 776.6 Section 776.6 Postal Service UNITED STATES POSTAL SERVICE ENVIRONMENTAL REGULATIONS FLOODPLAIN AND WETLAND PROCEDURES Floodplain Management § 776.6 Design requirements for construction. If structures impact, are located in, or support development in a...

Impact of nasal septal perforations of varying sizes and locations on the warming function of the nasal cavity: A computational fluid-dynamics analysis of 5 cases.

PubMed

Li, Lifeng; Han, Demin; Zhang, Luo; Li, Yunchuan; Zang, Hongrui; Wang, Tong; Liu, Yingxi

2016-09-01

Patients with a nasal septal perforation often exhibit symptoms associated with disturbed airflow, which can have an adverse effect on the warming function of the nasal cavity. The impact of this effect is not fully understood. The warming function is an important factor in the maintenance of nasal physiology. We conducted a study to investigate the impact of septal perforations of various sizes and locations on the warming function during inspiration in 5 patients-3 men and 2 women, aged 25 to 47 years. Three-dimensional computed tomography and computational fluid dynamics were used to model the flux of communication and temperature, and differences among patients were compared. All 5 patients exhibited an impairment of their nasal warming function. As the size of the perforation increased, the flux of communication increased and the warming function decreased. Perforations located in an anterior position were associated with greater damage to the warming function than those in a posterior position. In patients with a large or anteriorly located perforation, airflow temperature in the nasopharynx was decreased. Our findings suggest that septal perforations not only induce airflow disturbance, but they also impair the nasal warming function. Further analysis of warming function is necessary to better explore flow mechanisms in patients with structural abnormalities.

Geological remote sensing signatures of terrestrial impact craters

NASA Technical Reports Server (NTRS)

Garvin, J. B.; Schnetzler, C.; Grieve, R. A. F.

1988-01-01

Geological remote sensing techniques can be used to investigate structural, depositional, and shock metamorphic effects associated with hypervelocity impact structures, some of which may be linked to global Earth system catastrophies. Although detailed laboratory and field investigations are necessary to establish conclusive evidence of an impact origin for suspected crater landforms, the synoptic perspective provided by various remote sensing systems can often serve as a pathfinder to key deposits which can then be targetted for intensive field study. In addition, remote sensing imagery can be used as a tool in the search for impact and other catastrophic explosion landforms on the basis of localized disruption and anomaly patterns. In order to reconstruct original dimensions of large, complex impact features in isolated, inaccessible regions, remote sensing imagery can be used to make preliminary estimates in the absence of field geophysical surveys. The experienced gained from two decades of planetary remote sensing of impact craters on the terrestrial planets, as well as the techniques developed for recognizing stages of degradation and initial crater morphology, can now be applied to the problem of discovering and studying eroded impact landforms on Earth. Preliminary results of remote sensing analyses of a set of terrestrial impact features in various states of degradation, geologic settings, and for a broad range of diameters and hence energies of formation are summarized. The intention is to develop a database of remote sensing signatures for catastrophic impact landforms which can then be used in EOS-era global surveys as the basis for locating the possibly hundreds of missing impact structures. In addition, refinement of initial dimensions of extremely recent structures such as Zhamanshin and Bosumtwi is an important objective in order to permit re-evaluation of global Earth system responses associated with these types of events.

Original size of the Vredefort structure, South Africa

NASA Technical Reports Server (NTRS)

Therriault, A. M.; Reid, A. M.; Reimold, W. U.

1993-01-01

The Vredefort structure is located approximately 120 km southwest of Johannesburg, South Africa, and is deeply eroded. Controversies remain on the origin of this structure with the most popular hypotheses being: (1) by impact cratering about 2.0 Ga; (2) as a cryptoexplosion structure about 2.0 Ga; and (3) by purely tectonic processes starting at about 3.0 Ga and ending with the Vredefort event at 2.0 Ga. In view of recent work in which the granophyre dikes are interpreted as the erosional remants of a more extensive impact melt sheet, injected downward into the underlying country rocks, the impact origin hypothesis for Vredefort is adopted. In order to estimate the original dimensions of the Vredefort impact structure, it is assumed that the structure was initially circular, that its predeformation center corresponds to the center of the granitic core, and that the pre-Vredefort geology of the area prior to approximately 2.0 Ga ago is as suggested by Fletcher and Reimold. The spatial relationship between shock metamorphic effects, the shock pressures they record, and the morphological features of the crater were established for a number of large terrestrial craters. The principles of crater formation at large complex impact structures comparable in size to Vredefort were also established, although many details remain unresolved. An important conclusion is that the transient crater, which is formed directly by excavation and displacement by the shock-induced cratering flow-field (i.e., the particle velocity flow field existing in the region of the transient crater but behind the initial outgoing shock front), is highly modified during the late stage processes. The original transient crater diameter lies well within the final rim of the crater, which is established by structural movements during late-stage cavity modification.

The Use of Terrestrial Analogs in Preparing for Planetary Surface Exploration: Sampling and Radioisotopic Dating of Impactites and Deployment of In Situ Analytical Technologies

NASA Astrophysics Data System (ADS)

Young, Kelsey

Impact cratering has played a crucial role in the surface development of the inner planets. Constraining the timing of this bombardment history is important in understanding the origins of life and our planet's evolution. Plate tectonics, active volcanism, and vegetation hinder the preservation and identification of existing impact craters on Earth. Providing age constraints on these elusive structures will provide a deeper understanding of our planet's development. To do this, (U-Th)/He thermochronology and in situ 40 Ar/39Ar laser microprobe geochronology are used to provide ages for the Haughton and Mistastin Lake impact structures, both located in northern Canada. While terrestrial impact structures provide accessible laboratories for deciphering Earth's impact history, the ultimate goal for understanding the history of the reachable inner Solar System is to acquire robust, quantitative age constraints for the large lunar impact basins. The oldest of these is the South Pole-Aitken basin (SPA), located on the lunar farside. While it is known that this basin is stratigraphically the oldest on the Moon, its absolute age has yet to be determined. Several reports released in the last decade have highlighted sampling and dating SPA as a top priority for inner Solar System exploration. This is no easy task as the SPA structure has been modified by four billion subsequent years of impact events. Informed by studies at Mistastin---which has target lithologies analogous to those at SPA---sampling strategies are discussed that are designed to optimize the probability of a high science return with regard to robust geochronology of the SPA basin. Planetary surface missions, like one designed to explore and sample SPA, require the integration of engineering constraints with scientific goals and traverse planning. The inclusion of in situ geochemical technology, such as the handheld X-ray fluorescence spectrometer (hXRF), into these missions will provide human crews with the ability to gain a clearer contextual picture of the landing site and aid with sample high-grading. The introduction of hXRF technology could be of crucial importance in identifying SPA-derived melts. In addition to enhancing planetary field geology, hXRF deployment could also have real implications for enriching terrestrial field geology.

Survey of NASA research on crash dynamics

NASA Technical Reports Server (NTRS)

Thomson, R. G.; Carden, H. D.; Hayduk, R. J.

1984-01-01

Ten years of structural crash dynamics research activities conducted on general aviation aircraft by the National Aeronautics and Space Administration (NASA) are described. Thirty-two full-scale crash tests were performed at Langley Research Center, and pertinent data on airframe and seat behavior were obtained. Concurrent with the experimental program, analytical methods were developed to help predict structural behavior during impact. The effects of flight parameters at impact on cabin deceleration pulses at the seat/occupant interface, experimental and analytical correlation of data on load-limiting subfloor and seat configurations, airplane section test results for computer modeling validation, and data from emergency-locator-transmitter (ELT) investigations to determine probable cause of false alarms and nonactivations are assessed. Computer programs which provide designers with analytical methods for predicting accelerations, velocities, and displacements of collapsing structures are also discussed.

Noachian and Hesperian modification of the original Chryse impact basin topography

NASA Technical Reports Server (NTRS)

Stockman, S. A.; Frey, H.

1995-01-01

We prospose a new center and ring assignment for the original Chryse impact basin based upon photogeologic mapping of Noachian outcrops and re-examination of the published geology using orthographic projections. While others have centered the Chryse impact on the topographic low associated with Hesperian volcanic and fluvial deposits, we suggest that the center of the Noachian-age excavation cavity was located approximately 800 km to the north, and that the basin topography was modified significantly from the Noachian into the Hesperian. Evolution of the topographic low included structural modification by a later impact centered in Acidalia, restricted volcanic deposition and loading, localized subsidence, and restricted deposition from the circum-Chryse outlfow channels.

An arm wearable haptic interface for impact sensing on unmanned aerial vehicles

NASA Astrophysics Data System (ADS)

Choi, Yunshil; Hong, Seung-Chan; Lee, Jung-Ryul

2017-04-01

In this paper, an impact monitoring system using fiber Bragg grating (FBG) sensors and vibro-haptic actuators has been introduced. The system is suggested for structural health monitoring (SHM) for unmanned aerial vehicles (UAVs), by making a decision with human-robot interaction. The system is composed with two major subsystems; an on-board system equipped on UAV and an arm-wearable interface for ground pilot. The on-board system acquires impact-induced wavelength changes and performs localization process, which was developed based on arrival time calculation. The arm-wearable interface helps ground pilots to make decision about impact location themselves by stimulating their tactile-sense with motor vibration.

Impact of Interlayer Dwell Time on Microstructure and Mechanical Properties of Nickel and Titanium Alloys

NASA Astrophysics Data System (ADS)

Foster, B. K.; Beese, A. M.; Keist, J. S.; McHale, E. T.; Palmer, T. A.

2017-09-01

Path planning in additive manufacturing (AM) processes has an impact on the thermal histories experienced at discrete locations in simple and complex AM structures. One component of path planning in directed energy deposition is the time required for the laser or heat source to return to a given location to add another layer of material. As structures become larger and more complex, the length of this interlayer dwell time can significantly impact the resulting thermal histories. The impact of varying dwell times between 0 and 40 seconds on the microstructural and mechanical properties of Inconel® 625 and Ti-6Al-4V builds has been characterized. Even though these materials display different microstructures and solid-state phase transformations, the addition of an interlayer dwell generally led to a finer microstructure in both materials that impacted the resulting mechanical properties. With the addition of interlayer dwell times up to 40 seconds in the Inconel® 625 builds, finer secondary dendrite arm spacing values, produced by changes in the thermal history, correspond to increased yield and tensile strengths. These mechanical properties did not appear to change significantly, however, for dwell times greater than 20 seconds in the Inconel® 625 builds, indicating that longer dwell times have a minimal impact. The addition of interlayer dwell times in Ti-6Al-4V builds resulted in a slight decrease in the measured alpha lath widths and a much more noticeable decrease in the width of prior beta grains. In addition, the yield and tensile values continued to increase, nearly reaching the values observed in the rolled plate substrate material with dwell times up to 40 seconds.

Newly identified "Tunnunik" impact structure, Prince Albert Peninsula, northwestern Victoria Island, Arctic Canada

NASA Astrophysics Data System (ADS)

Dewing, Keith; Pratt, Brian R.; Hadlari, Thomas; Brent, Tom; BÉDard, Jean; Rainbird, Robert H.

2013-02-01

Regional geological mapping of the glaciated surface of northwestern Victoria Island in the western Canadian Arctic revealed an anomalous structure in otherwise flat-lying Neoproterozoic and lower Paleozoic carbonate rocks, located south of Richard Collinson Inlet. The feature is roughly circular in plan view, approximately 25 km in diameter, and characterized by quaquaversal dips of approximately 45°, decreasing laterally. The core of the feature also exhibits local vertical dips, low-angle reverse faults, and drag folds. Although brecciation was not observed, shatter cones are pervasive in all lithologies in the central area, including 723 Ma old dikes that penetrate Neoproterozoic limestones. Their abundance decreases distally, and none was observed in surrounding, horizontally bedded strata. This circular structure is interpreted as a deeply eroded meteorite impact crater of the complex type, and the dipping strata as the remnants of the central uplift. The variation in orientation and shape of shatter cones point to variably oriented stresses with the passage of the shock wave, possibly related to the presence of pore water in the target strata as well as rock type and lithological heterogeneities, especially bed thickness. Timing of impact is poorly constrained. The youngest rocks affected are Late Ordovician (approximately 450 Ma) and the impact structure is mantled by undisturbed postglacial sediments. Regional, hydrothermal dolomitization of the Ordovician limestones, possibly in the Late Devonian (approximately 360 Ma), took place before the impact, and widespread WSW-ENE-trending normal faults of probable Early Cretaceous age (approximately 130 Ma) apparently cross-cut the impact structure.

Concrete Condition Assessment Using Impact-Echo Method and Extreme Learning Machines

PubMed Central

Zhang, Jing-Kui; Yan, Weizhong; Cui, De-Mi

2016-01-01

The impact-echo (IE) method is a popular non-destructive testing (NDT) technique widely used for measuring the thickness of plate-like structures and for detecting certain defects inside concrete elements or structures. However, the IE method is not effective for full condition assessment (i.e., defect detection, defect diagnosis, defect sizing and location), because the simple frequency spectrum analysis involved in the existing IE method is not sufficient to capture the IE signal patterns associated with different conditions. In this paper, we attempt to enhance the IE technique and enable it for full condition assessment of concrete elements by introducing advanced machine learning techniques for performing comprehensive analysis and pattern recognition of IE signals. Specifically, we use wavelet decomposition for extracting signatures or features out of the raw IE signals and apply extreme learning machine, one of the recently developed machine learning techniques, as classification models for full condition assessment. To validate the capabilities of the proposed method, we build a number of specimens with various types, sizes, and locations of defects and perform IE testing on these specimens in a lab environment. Based on analysis of the collected IE signals using the proposed machine learning based IE method, we demonstrate that the proposed method is effective in performing full condition assessment of concrete elements or structures. PMID:27023563

Numerical analysis of nuclear power plant structure subjected to aircraft crash

NASA Astrophysics Data System (ADS)

Saberi, Reza; Alinejad, Majid; Mahdavi, Mir Omid; Sepanloo, Kamran

2017-12-01

An aircraft crashing into a nuclear containment may induce a series of disasters related to containment capacity, including local penetration and perforation of the containment, intensive vibrations, and fire ignited after jet fuel leakage. In this study, structural safety of a reinforced concrete containment vessel (RCCV) has been studied against the direct hit of Airbus A320, Boeing 707-320 and Phantom F4 aircrafts. ABAQUS/explicit finite element code has been used to carry out the three-dimensional numerical simulations. The impact locations identified on the nuclear containment structure are mid height of containment, center of the cylindrical portion, junction of dome and cylinder, and over the cylindrical portion close to the foundation level. The loading of the aircraft has been assigned through the corresponding reaction-time response curve. The concrete damaged plasticity model was predicted to simulate the behavior of concrete while the behavior of steel reinforcement was incorporated using elastoplastic material model. Dynamic loading conditions were considered using dynamic increase factor. The mid height of containment and center of cylindrical portion have been found to experience most severe deformation against each aircraft crash. It has also been found that compression damage in concrete is not critical at none of the impact locations.

Brain tissue strains vary with head impact location: A possible explanation for increased concussion risk in struck versus striking football players.

PubMed

Elkin, Benjamin S; Gabler, Lee F; Panzer, Matthew B; Siegmund, Gunter P

2018-03-29

On-field football helmet impacts over a large range of severities have caused concussions in some players but not in other players. One possible explanation for this variability is the struck player's helmet impact location. We examined the effect of impact location on regional brain tissue strain when input energy was held constant. Laboratory impacts were performed at 12 locations distributed over the helmet and the resulting head kinematics were simulated in two finite element models of the brain: the Simulated Injury Monitor and the Global Human Body Model Consortium brain model. Peak kinematics, injury metrics and brain strain varied significantly with impact location. Differences in impact location explained 33 to 37% of the total variance in brain strain for the whole brain and cerebrum, considerably more than the variance explained by impact location for the peak resultant head kinematics (8 to 23%) and slightly more than half of the variance explained by the difference in closing speed (57 to 61%). Both finite element models generated similar strain results, with minor variations for impacts that generated multi-axial rotations, larger variations in brainstem strains for some impact locations and a small bias for the cerebellum. Based on this experimental and computational simulation study, impact location on the football helmet has a large effect on regional brain tissue strain. We also found that the lowest strains consistently occurred in impacts to the crown and forehead, helmet locations commonly associated with the striking player. Copyright © 2018 Elsevier Ltd. All rights reserved.

An Investigation on Low Velocity Impact Response of Multilayer Sandwich Composite Structures

PubMed Central

Jedari Salami, S.; Sadighi, M.; Shakeri, M.; Moeinfar, M.

2013-01-01

The effects of adding an extra layer within a sandwich panel and two different core types in top and bottom cores on low velocity impact loadings are studied experimentally in this paper. The panel includes polymer composite laminated sheets for faces and the internal laminated sheet called extra layer sheet, and two types of crushable foams are selected as the core material. Low velocity impact tests were carried out by drop hammer testing machine to the clamped multilayer sandwich panels with expanded polypropylene (EPP) and polyurethane rigid (PUR) in the top and bottom cores. Local displacement of the top core, contact force and deflection of the sandwich panel were obtained for different locations of the internal sheet; meanwhile the EPP and PUR were used in the top and bottom cores alternatively. It was found that the core material type has made significant role in improving the sandwich panel's behavior compared with the effect of extra layer location. PMID:24453804

Development of an FBG Sensor Array for Multi-Impact Source Localization on CFRP Structures.

PubMed

Jiang, Mingshun; Sai, Yaozhang; Geng, Xiangyi; Sui, Qingmei; Liu, Xiaohui; Jia, Lei

2016-10-24

We proposed and studied an impact detection system based on a fiber Bragg grating (FBG) sensor array and multiple signal classification (MUSIC) algorithm to determine the location and the number of low velocity impacts on a carbon fiber-reinforced polymer (CFRP) plate. A FBG linear array, consisting of seven FBG sensors, was used for detecting the ultrasonic signals from impacts. The edge-filter method was employed for signal demodulation. Shannon wavelet transform was used to extract narrow band signals from the impacts. The Gerschgorin disc theorem was used for estimating the number of impacts. We used the MUSIC algorithm to obtain the coordinates of multi-impacts. The impact detection system was tested on a 500 mm × 500 mm × 1.5 mm CFRP plate. The results show that the maximum error and average error of the multi-impacts' localization are 9.2 mm and 7.4 mm, respectively.

On impact damage detection and quantification for CFRP laminates using structural response data only

NASA Astrophysics Data System (ADS)

Sultan, M. T. H.; Worden, K.; Pierce, S. G.; Hickey, D.; Staszewski, W. J.; Dulieu-Barton, J. M.; Hodzic, A.

2011-11-01

The overall purpose of the research is to detect and attempt to quantify impact damage in structures made from composite materials. A study that uses simplified coupon specimens made from a Carbon Fibre-Reinforced Polymer (CFRP) prepreg with 11, 12 and 13 plies is presented. PZT sensors were placed at three separate locations in each test specimen to record the responses from impact events. To perform damaging impact tests, an instrumented drop-test machine was used and the impact energy was set to cover a range of 0.37-41.72 J. The response signals captured from each sensor were recorded by a data acquisition system for subsequent evaluation. The impacted specimens were examined with an X-ray technique to determine the extent of the damaged areas and it was found that the apparent damaged area grew monotonically with impact energy. A number of simple univariate and multivariate features were extracted from the sensor signals recorded during impact by computing their spectra and calculating frequency centroids. The concept of discordancy from the statistical discipline of outlier analysis is employed in order to separate the responses from non-damaging and damaging impacts. The results show that the potential damage indices introduced here provide a means of identifying damaging impacts from the response data alone.

The Apollo peak-ring impact basin: Insights into the structure and evolution of the South Pole-Aitken basin

NASA Astrophysics Data System (ADS)

Potter, Ross W. K.; Head, James W.; Guo, Dijun; Liu, Jianzhong; Xiao, Long

2018-05-01

The 492 km-diameter Apollo impact basin post-dates, and is located at the inner edge of, the ∼2240 km-diameter South Pole-Aitken (SPA) basin, providing an opportunity to assess the SPA substructure and lateral heterogeneity. Gravity Recovery and Interior Laboratory gravity data suggest an average crustal thickness on the floor of SPA of ∼20 km and within the Apollo basin of ∼5 km, yet remote sensing data reveal no conclusive evidence for the presence of exposed mantle material. We use the iSALE shock physics code to model the formation of the Apollo basin and find that the observational data are best fit by the impact of a 40 km diameter body traveling at 15 km/s into 20-40 km thick crustal material. These results strongly suggest that the Apollo impact occurred on ejecta deposits and collapsed crustal material of the SPA basin and could help place constraints on the location, size and geometry of the SPA transient cavity. The peak ring in the interior of Apollo basin is plausibly interpreted to be composed of inwardly collapsed lower crustal material that experienced peak shock pressures in excess of 35 GPa, consistent with remote sensing observations that suggest shocked plagioclase. Proposed robotic and/or human missions to SPA and Apollo would present an excellent opportunity to test the predictions of this work and address many scientific questions about SPA basin evolution and structure.

Simulation of cooling efficiency via miniaturised channels in multilayer LTCC for power electronics

NASA Astrophysics Data System (ADS)

Pietrikova, Alena; Girasek, Tomas; Lukacs, Peter; Welker, Tilo; Müller, Jens

2017-03-01

The aim of this paper is detailed investigation of thermal resistance, flow analysis and distribution of coolant as well as thermal distribution inside multilayer LTCC substrates with embedded channels for power electronic devices by simulation software. For this reason four various structures of internal channels in the multilayer LTCC substrates were designed and simulated. The impact of the volume flow, structures of channels, and power loss of chip was simulated, calculated and analyzed by using the simulation software Mentor Graphics FloEFDTM. The structure, size and location of channels have the significant impact on thermal resistance, pressure of coolant as well as the effectivity of cooling power components (chips) that can be placed on the top of LTCC substrate. The main contribution of this paper is thermal analyze, optimization and impact of 4 various cooling channels embedded in LTCC multilayer structure. Paper investigate, the effect of volume flow in cooling channels for achieving the least thermal resistance of LTCC substrate that is loaded by power thermal chips. Paper shows on the impact of the first chips thermal load on the second chip as well as. This possible new technology could ensure in the case of practical realization effective cooling and increasing reliability of high power modules.

SU-E-T-170: Characterization of the Location, Extent, and Proximity to Critical Structures of Target Volumes Provides Detail for Improved Outcome Predictions Among Pancreatic Cancer Patients

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Z; Moore, J; Rosati, L

Purpose: In radiotherapy, size, location and proximity of the target to critical structures influence treatment decisions. It has been shown that proximity of the target predicts dosimetric sparing of critical structures. In addition to dosimetry, precise location of disease has further implications such as tumor invasion, or proximity to major arteries that inhibit surgery. Knowledge of which patients can be converted to surgical candidates by radiation may have high impact on future treat/no-treat decisions. We propose a method to improve our characterization of the location of pancreatic cancer and treatment volume extent with respect to nearby arteries with the goalmore » of developing features to improve clinical predictions and decisions. Methods: Oncospace is a local learning health system that systematically captures clinical outcomes and all aspects of radiotherapy treatment plans, including overlap volume histograms (OVH) – a measure of spatial relationships between two structures. Minimum and maximum distances of PTV and OARs based on OVH, PTV volume, anatomic location by ICD-9 code, and surgical outcome were queried. Normalized distance to center from the left and right kidney was calculated to indicate tumor location and laterality. Distance to critical arteries (celiac, superior mesenteric, common hepatic) is validated by surgical status (borderline resectable, locally advanced converted to resectable). Results: There were 205 pancreas stereotactic body radiotherapy patients treated from 2009–2015 queried. Location/laterality of tumor based on kidney OVH show strong trends between location by OVH and by ICD-9. Compared to the locally advanced group, the borderline resectable group showed larger geometrical distance from critical arteries (p=0.03). Conclusion: Our platform enabled analysis of shape/size-location relationships. These data suggest that PTV volume and attention to distance between PTVs and surrounding OARs and major arteries may be promising for improving characterization of treatment anatomy that can refine our ability for outcome predictions and decision making. Elekta, Toshiba.« less

Invasive plants transform the three-dimensional structure of rain forests

Treesearch

Gegory P. Asner; R. Flint Hughes; Peter M. Vitousek; David E. Knapp; Ty Kennedy-Bowdoin; Joseph Boardman; Roberta E. Martin; Michael Eastwood; Robert O. Green

2008-01-01

Biological invasions contribute to global environmental change, but the dynamics and consequences of most invasions are difficult to assess at regional scales. We deployed an airborne remote sensing system that mapped the location and impacts of five highly invasive plant species across 221,875 ha of Hawaiian ecosystems, identifying four distinct ways that these...

Teacher Response to Proposed Changes in Grouping: Impact on Policy and Practice.

ERIC Educational Resources Information Center

Anderson, Carolyn S.; Barr, Rebecca

Grouping for instruction has characteristics that make existing structures, habits, and attitudes resistant to change. This case study accordingly describes a school district located 40 miles south of Chicago in which attempts were made to change attitudes about, and the practice of, instructional grouping over a 3-year period. Two ways are…

Urban growth and landscape connectivity threats assessment at Saguaro National Park, Arizona, USA

USGS Publications Warehouse

Perkl, Ryan; Norman, Laura M.; Mitchell, David; Feller, Mark R.; Smith, Garrett; Wilson, Natalie R.

2018-01-01

Urban and exurban expansion results in habitat and biodiversity loss globally. We hypothesize that a coupled-model approach could connect urban planning for future cities with landscape ecology to consider wildland habitat connectivity. Our work combines urban growth simulations with models of wildlife corridors to examine how species will be impacted by development to test this hypothesis. We leverage a land use change model (SLEUTH) with structural and functional landscape-connectivity modeling techniques to ascertain the spatial extent and locations of connectivity related threats to a national park in southern Arizona, USA, and describe how protected areas might be impacted by urban expansion. Results of projected growth significantly altered structural connectivity (80%) when compared to current (baseline) corridor conditions. Moreover, projected growth impacted functional connectivity differently amongst species, indicating resilience of some species and near-complete displacement of others. We propose that implementing a geospatial-design-based model will allow for a better understanding of the impacts management decisions have on wildlife populations. The application provides the potential to understand both human and environmental impacts of land-system dynamics, critical for long-term sustainability.

Use of Anthropogenic Sea Floor Structures by Australian Fur Seals: Potential Positive Ecological Impacts of Marine Industrial Development?

PubMed Central

Arnould, John P. Y.; Monk, Jacquomo; Ierodiaconou, Daniel; Hindell, Mark A.; Semmens, Jayson; Hoskins, Andrew J.; Costa, Daniel P.; Abernathy, Kyler; Marshall, Greg J.

2015-01-01

Human-induced changes to habitats can have deleterious effects on many species that occupy them. However, some species can adapt and even benefit from such modifications. Artificial reefs have long been used to provide habitat for invertebrate communities and promote local fish populations. With the increasing demand for energy resources within ocean systems, there has been an expansion of infrastructure in near-shore benthic environments which function as de facto artificial reefs. Little is known of their use by marine mammals. In this study, the influence of anthropogenic sea floor structures (pipelines, cable routes, wells and shipwrecks) on the foraging locations of 36 adult female Australian fur seals (Arctocephalus pusillus doriferus) was investigated. For 9 (25%) of the individuals, distance to anthropogenic sea floor structures was the most important factor in determining the location of intensive foraging activity. Whereas the influence of anthropogenic sea floor structures on foraging locations was not related to age and mass, it was positively related to flipper length/standard length (a factor which can affect manoeuvrability). A total of 26 (72%) individuals tracked with GPS were recorded spending time in the vicinity of structures (from <1% to >75% of the foraging trip duration) with pipelines and cable routes being the most frequented. No relationships were found between the amount of time spent frequenting anthropogenic structures and individual characteristics. More than a third (35%) of animals foraging near anthropogenic sea floor structures visited more than one type of structure. These results further highlight potentially beneficial ecological outcomes of marine industrial development. PMID:26132329

Use of Anthropogenic Sea Floor Structures by Australian Fur Seals: Potential Positive Ecological Impacts of Marine Industrial Development?

PubMed

Arnould, John P Y; Monk, Jacquomo; Ierodiaconou, Daniel; Hindell, Mark A; Semmens, Jayson; Hoskins, Andrew J; Costa, Daniel P; Abernathy, Kyler; Marshall, Greg J

2015-01-01

Human-induced changes to habitats can have deleterious effects on many species that occupy them. However, some species can adapt and even benefit from such modifications. Artificial reefs have long been used to provide habitat for invertebrate communities and promote local fish populations. With the increasing demand for energy resources within ocean systems, there has been an expansion of infrastructure in near-shore benthic environments which function as de facto artificial reefs. Little is known of their use by marine mammals. In this study, the influence of anthropogenic sea floor structures (pipelines, cable routes, wells and shipwrecks) on the foraging locations of 36 adult female Australian fur seals (Arctocephalus pusillus doriferus) was investigated. For 9 (25%) of the individuals, distance to anthropogenic sea floor structures was the most important factor in determining the location of intensive foraging activity. Whereas the influence of anthropogenic sea floor structures on foraging locations was not related to age and mass, it was positively related to flipper length/standard length (a factor which can affect manoeuvrability). A total of 26 (72%) individuals tracked with GPS were recorded spending time in the vicinity of structures (from <1% to >75% of the foraging trip duration) with pipelines and cable routes being the most frequented. No relationships were found between the amount of time spent frequenting anthropogenic structures and individual characteristics. More than a third (35%) of animals foraging near anthropogenic sea floor structures visited more than one type of structure. These results further highlight potentially beneficial ecological outcomes of marine industrial development.

Distribution and interplay of geologic processes on Titan from Cassini radar data

USGS Publications Warehouse

Lopes, R.M.C.; Stofan, E.R.; Peckyno, R.; Radebaugh, J.; Mitchell, K.L.; Mitri, Giuseppe; Wood, C.A.; Kirk, R.L.; Wall, S.D.; Lunine, J.I.; Hayes, A.; Lorenz, R.; Farr, Tom; Wye, L.; Craig, J.; Ollerenshaw, R.J.; Janssen, M.; LeGall, A.; Paganelli, F.; West, R.; Stiles, B.; Callahan, P.; Anderson, Y.; Valora, P.; Soderblom, L.

2010-01-01

The Cassini Titan Radar Mapper is providing an unprecedented view of Titan's surface geology. Here we use Synthetic Aperture Radar (SAR) image swaths (Ta-T30) obtained from October 2004 to December 2007 to infer the geologic processes that have shaped Titan's surface. These SAR swaths cover about 20% of the surface, at a spatial resolution ranging from ???350 m to ???2 km. The SAR data are distributed over a wide latitudinal and longitudinal range, enabling some conclusions to be drawn about the global distribution of processes. They reveal a geologically complex surface that has been modified by all the major geologic processes seen on Earth - volcanism, tectonism, impact cratering, and erosion and deposition by fluvial and aeolian activity. In this paper, we map geomorphological units from SAR data and analyze their areal distribution and relative ages of modification in order to infer the geologic evolution of Titan's surface. We find that dunes and hummocky and mountainous terrains are more widespread than lakes, putative cryovolcanic features, mottled plains, and craters and crateriform structures that may be due to impact. Undifferentiated plains are the largest areal unit; their origin is uncertain. In terms of latitudinal distribution, dunes and hummocky and mountainous terrains are located mostly at low latitudes (less than 30??), with no dunes being present above 60??. Channels formed by fluvial activity are present at all latitudes, but lakes are at high latitudes only. Crateriform structures that may have been formed by impact appear to be uniformly distributed with latitude, but the well-preserved impact craters are all located at low latitudes, possibly indicating that more resurfacing has occurred at higher latitudes. Cryovolcanic features are not ubiquitous, and are mostly located between 30?? and 60?? north. We examine temporal relationships between units wherever possible, and conclude that aeolian and fluvial/pluvial/lacustrine processes are the most recent, while tectonic processes that led to the formation of mountains and Xanadu are likely the most ancient. ?? 2009 Elsevier Inc.

Disribution and interplay of geologic processes on Titan from Cassini radar data

USGS Publications Warehouse

Lopes, R.M.C.; Stofan, E.R.; Peckyno, R.; Radebaugh, J.; Mitchell, K.L.; Mitri, Giuseppe; Wood, C.A.; Kirk, R.L.; Wall, S.D.; Lunine, J.I.; Hayes, A.; Lorenz, R.; Farr, Tom; Wye, L.; Craig, J.; Ollerenshaw, R.J.; Janssen, M.; LeGall, A.; Paganelli, F.; West, R.; Stiles, B.; Callahan, P.; Anderson, Y.; Valora, P.; Soderblom, L.

2010-01-01

The Cassini Titan Radar Mapper is providing an unprecedented view of Titan's surface geology. Here we use Synthetic Aperture Radar (SAR) image swaths (Ta-T30) obtained from October 2004 to December 2007 to infer the geologic processes that have shaped Titan's surface. These SAR swaths cover about 20% of the surface, at a spatial resolution ranging from ~350 m to ~2 km. The SAR data are distributed over a wide latitudinal and longitudinal range, enabling some conclusions to be drawn about the global distribution of processes. They reveal a geologically complex surface that has been modified by all the major geologic processes seen on Earth - volcanism, tectonism, impact cratering, and erosion and deposition by fluvial and aeolian activity. In this paper, we map geomorphological units from SAR data and analyze their areal distribution and relative ages of modification in order to infer the geologic evolution of Titan's surface. We find that dunes and hummocky and mountainous terrains are more widespread than lakes, putative cryovolcanic features, mottled plains, and craters and crateriform structures that may be due to impact. Undifferentiated plains are the largest areal unit; their origin is uncertain. In terms of latitudinal distribution, dunes and hummocky and mountainous terrains are located mostly at low latitudes (less than 30 degrees), with no dunes being present above 60 degrees. Channels formed by fluvial activity are present at all latitudes, but lakes are at high latitudes only. Crateriform structures that may have been formed by impact appear to be uniformly distributed with latitude, but the well-preserved impact craters are all located at low latitudes, possibly indicating that more resurfacing has occurred at higher latitudes. Cryovolcanic features are not ubiquitous, and are mostly located between 30 degrees and 60 degrees north. We examine temporal relationships between units wherever possible, and conclude that aeolian and fluvial/pluvial/lacustrine processes are the most recent, while tectonic processes that led to the formation of mountains and Xanadu are likely the most ancient.

Search for Impact Craters in the Volcanic and Volcano-Sedimentary Terrains of Mexico

NASA Astrophysics Data System (ADS)

Bartali, R.; Fucugauchi, J. U.

2011-12-01

It has long been recognized that the numbers of impact craters documented in the terrestrial record are small compared to those of the Moon and other planets and satellites. Processes acting on the Earth surface including tectonics, volcanism and erosion contribute to erase, modify and cover evidence of crater-forming impacts that have occurred through Earth's history. Even evidence on large impact structures is limited to few examples, with only three complex multi-ring structures so far recognized. Chicxulub is a ~200 km diameter multi-ring crater formed by an impact in the southern Gulf of Mexico about 65.5 Ma ago at the Cretaceous/Paleogene boundary. Chicxulub is the only impact structure documented in Mexico, Central and northern South America (http:www.unb.ca/passc/ImpactDatabase). Chicxulub, located in the Yucatan platform buried under a kilometer of carbonate rocks, was initially identified from its concentric semi-circular gravity and magnetic anomaly patterns. Yucatan peninsula has a low-relief topography and high contrasts in physical properties between carbonate rocks, impact lithologies and deformed target rocks. In contrast, most of the country has an abrupt topography with limited outcrops of Paleozoic and Precambrian terrains. The extensive igneous cover of the Sierra Madre Occidental, Trans-Mexican volcanic belt and Sierra Madre del Sur makes search for impact craters a difficult task. Early attempts were limited by the numerous volcanic craters and lack of high-resolution geophysical data. As part of a new country-wide search program, we have been conducting studies in northern Mexico using remote sensing and geophysical data to document circular and semi-circular crater-like features. The search has identified several structures, some well exposed and characterized by simple crater morphologies and topographic rims. These landforms have been mapped, estimating their dimensions, distribution and characterizing the surrounding terrains. Aeromagnetic anomaly data from low-altitude surveys have been used to characterize the structures, together with geological and topographic maps. For the promising sites, low altitude aerial images and on-site reconnaissance surveys and sampling are completed. Sites studied include isolated structures built on low relief terrains as well as multiple crater-like structures on volcanic terrains. Here we present initial results of the project in the Chihuahua region and discuss the methods, findings and difficulties in identification of impact structures.

Modeling photosynthesis of Spartina alterniflora (smooth cordgrass) impacted by the Deepwater Horizon oil spill using Bayesian inference

NASA Astrophysics Data System (ADS)

Wu, Wei; Biber, Patrick D.; Peterson, Mark S.; Gong, Chongfeng

2012-12-01

To study the impact of the Deepwater Horizon oil spill on photosynthesis of coastal salt marsh plants in Mississippi, we developed a hierarchical Bayesian (HB) model based on field measurements collected from July 2010 to November 2011. We sampled three locations in Davis Bayou, Mississippi (30.375°N, 88.790°W) representative of a range of oil spill impacts. Measured photosynthesis was negative (respiration only) at the heavily oiled location in July 2010 only, and rates started to increase by August 2010. Photosynthesis at the medium oiling location was lower than at the control location in July 2010 and it continued to decrease in September 2010. During winter 2010-2011, the contrast between the control and the two impacted locations was not as obvious as in the growing season of 2010. Photosynthesis increased through spring 2011 at the three locations and decreased starting with October at the control location and a month earlier (September) at the impacted locations. Using the field data, we developed an HB model. The model simulations agreed well with the measured photosynthesis, capturing most of the variability of the measured data. On the basis of the posteriors of the parameters, we found that air temperature and photosynthetic active radiation positively influenced photosynthesis whereas the leaf stress level negatively affected photosynthesis. The photosynthesis rates at the heavily impacted location had recovered to the status of the control location about 140 days after the initial impact, while the impact at the medium impact location was never severe enough to make photosynthesis significantly lower than that at the control location over the study period. The uncertainty in modeling photosynthesis rates mainly came from the individual and micro-site scales, and to a lesser extent from the leaf scale.

Characterization of Aircraft Structural Damage Using Guided Wave Based Finite Element Analysis for In-Flight Structural Health Management

NASA Technical Reports Server (NTRS)

Seshadri, Banavara R.; Krishnamurthy, Thiagarajan; Ross, Richard W.

2016-01-01

The development of multidisciplinary Integrated Vehicle Health Management (IVHM) tools will enable accurate detection, diagnosis and prognosis of damage under normal and adverse conditions during flight. The adverse conditions include loss of control caused by environmental factors, actuator and sensor faults or failures, and structural damage conditions. A major concern is the growth of undetected damage/cracks due to fatigue and low velocity foreign object impact that can reach a critical size during flight, resulting in loss of control of the aircraft. To avoid unstable catastrophic propagation of damage during a flight, load levels must be maintained that are below the load-carrying capacity for damaged aircraft structures. Hence, a capability is needed for accurate real-time predictions of safe load carrying capacity for aircraft structures with complex damage configurations. In the present work, a procedure is developed that uses guided wave responses to interrogate damage. As the guided wave interacts with damage, the signal attenuates in some directions and reflects in others. This results in a difference in signal magnitude as well as phase shifts between signal responses for damaged and undamaged structures. Accurate estimation of damage size and location is made by evaluating the cumulative signal responses at various pre-selected sensor locations using a genetic algorithm (GA) based optimization procedure. The damage size and location is obtained by minimizing the difference between the reference responses and the responses obtained by wave propagation finite element analysis of different representative cracks, geometries and sizes.

Analysis of LDEF micrometeoroid/debris data and damage to composite materials

NASA Technical Reports Server (NTRS)

Tennyson, R. C.; Manuelpillai, G.

1993-01-01

This report presented published LDEF micrometeoroid/debris impact data in a nomogram format useful for estimating the total number of hits that could be expected on a space structure as a function of time in orbit, angular location relative to ram, and exposed surface area. Correction factors accounting for different altitudes are given. These are normalized to the average LDEF altitude. Examples on how to use the nomograph are also included. In addition, impact data and damage areas observed on composite laminates (experiment AO 180) are discussed.

Orion Ground Test Article Water Impact Tests: Photogrammetric Evaluation of Impact Conditions

NASA Technical Reports Server (NTRS)

Vassilakos, Gregory J.; Mark, Stephen D.

2018-01-01

The Ground Test Article (GTA) is an early production version of the Orion Crew Module (CM). The structural design of the Orion CM is being developed based on LS-DYNA water landing simulations. As part of the process of confirming the accuracy of LS-DYNA water landing simulations, the GTA water impact test series was conducted at NASA Langley Research Center (LaRC) to gather data for comparison with simulations. The simulation of the GTA water impact tests requires the accurate determination of the impact conditions. To accomplish this, the GTA was outfitted with an array of photogrammetry targets. The photogrammetry system utilizes images from two cameras with a specialized tracking software to determine time histories for the 3-D coordinates of each target. The impact conditions can then be determined from the target location data.

Earth observation taken by the Expedition 20 crew

NASA Image and Video Library

2009-07-25

ISS020-E-026195 (25 July 2009) --- Aorounga Impact Crater is featured in this image photographed by an Expedition 20 crew member on the International Space Station. Aorounga Impact Crater is located in the Sahara Desert of north-central Chad and is one of the best preserved impact structures in the world. According to scientists, the crater is thought to be middle or upper Devonian to lower Mississippian (approximately 345 ? 370 million years old) based on the age of the sedimentary rocks deformed by the impact. Spaceborne Imaging Radar (SIR) data collected in 1994 suggests that Aorounga is one of a set of three craters formed by the same impact event. The other two suggested impact structures are buried by sand deposits. The concentric ring structure of the Aorounga crater ? renamed Aorounga South in the multiple-crater interpretation of SIR data ? is clearly visible in this detailed photograph. The central highland, or peak, of the crater is surrounded by a small sand-filled trough; this in turn is surrounded by a larger circular trough. Linear rock ridges alternating with light orange sand deposits cross the image from upper left to lower right; these are called yardangs by geomorphologists. Yardangs form by wind erosion of exposed rock layers in a unidirectional wind field. The wind blows from the northeast at Aorounga, and sand dunes formed between the yardangs are actively migrating to the southwest.

Impact of anthropogenic pressure on the formation of population structure and genetic diversity of raccoon dog Nyctereutes procyonoides

PubMed Central

Griciuvienė, Loreta; Paulauskas, Algimantas; Radzijevskaja, Jana; Žukauskienė, Judita; Pūraitė, Irma

2016-01-01

Abstract The raccoon dog Nyctereutes procyonoides experienced an active introduction and acclimatization in the European part of Russia followed by its migration to and colonization in the neighboring countries. Eventually, it has spread rapidly into many European countries. N. procyonoides probably invaded Lithuania from the neighboring countries of Belarus and Latvia where the species was introduced. However, the data on genetic diversity and population structure of the raccoon dogs in the recently invaded territories are still scarce. The objectives of this study were to investigate genetic diversity of N. procyonoides in Lithuania after acclimatization, and to assess the impact of anthropogenic pressure on the formation of population structure. A total of 147 N. procyonoides individuals collected from different regions of Lithuania were genotyped using 17 microsatellite markers. The microsatellite analysis of raccoon dogs indicated high levels of genetic diversity within the population. The Bayesian clustering analysis in STRUCTURE identified 4 genetic clusters among sampled raccoon dogs that could not reveal a clear separation between subpopulations. The widespread distribution of raccoon dogs in Lithuania, high level of genetic variation observed within subpopulations, and low level of variation portioned among subpopulations suggest migration and gene flow among locations. The significant correlation between genetic and geographic distances indicated isolation that reflected the distance between locations. The fencing of highways and very intensive traffic could be barriers to gene flow between the western and eastern sampling areas of raccoon dogs. PMID:29491930

Environmental Assessment of remedial action at the Ambrosia Lake uranium mill tailings site, Ambrosia Lake, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1987-06-01

This document assesses and compares the environmental impacts of various alternatives for remedial action at the Ambrosia Lake uranium mill tailings site located near Ambrosia Lake, New Mexico. The designated site covers 196 acres and contains 111 acres of tailings and some of the original mill structures. The Uranium Mill Tailings Radiation Control Act (UMTRCA), Public Law 95-604, authorizes the US Department of Energy to clean up the site to reduce the potential health impacts associated with the residual radioactive materials remaining at the site and at associated properties off the site. The US Environmental Protection Agency promulgated standards formore » th remedial action (40 CFR Part 192). Remedial action must be performed in accordance with these standards and with the concurrence of the Nuclear Regulatory Commission. The proposed action is to stabilize the tailings at their present location by consolidating the tailings and associated contaminated materials into a recontoured pile. A radon barrier would be constructed over the pile and various erosion protection measures would be taken to assure the long-term stability of the pile. Another alternative which would involve moving the tailings to a new location is also assessed in this document. This alternative would generally involve greater short-term impacts and costs but would result in stabilization of the tailings at an undeveloped location. The no action alternative is also assessed in this document.« less

Functional and Structural Impact of Target Uridine Substitutions on the H/ACA Ribonucleoprotein Particle Pseudouridine Synthase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Jing; Liang, Bo; Li, Hong

2010-09-17

Box H/ACA ribonucleoprotein protein particles catalyze the majority of pseudouridylation in functional RNA. Different from stand alone pseudouridine synthases, the RNP pseudouridine synthase comprises multiple protein subunits and an RNA subunit. Previous studies showed that each subunit, regardless its location, is sensitive to the step of subunit placement at the catalytic center and potentially to the reaction status of the substrate. Here we describe the impact of chemical substitutions of target uridine on enzyme activity and structure. We found that 3-methyluridine in place of uridine inhibited its isomerization while 2{prime}-deoxyuridine or 4-thiouridine did not. Significantly, crystal structures of an archaealmore » box H/ACA RNP bound with the nonreactive and the two postreactive substrate analogues showed only subtle structural changes throughout the assembly except for a conserved tyrosine and a substrate anchoring loop of Cbf5. Our results suggest a potential role of these elements and the subunit that contacts them in substrate binding and product release.« less

The impact of landscape disturbance on spatial genetic structure in the Guanacaste tree, Enterolobium cyclocarpum (Fabaceae).

PubMed

Gonzales, Eva; Hamrick, James L; Smouse, Peter E; Trapnell, Dorset W; Peakall, Rod

2010-01-01

We examined spatial genetic structure (SGS) in Enterolobium cyclocarpum (the Guanacaste tree), a dominant tree of Central American dry forests in 4 sites in Guanacaste Province, Costa Rica. In disturbed dry forest sites (e.g., pastures), E. cyclocarpum is primarily dispersed by cattle and horses, whose movements are restricted by pasture boundaries. The study sites varied in tree densities and disturbance. Allozyme analyses of adult trees demonstrated significant levels of SGS in 3 of 4 sites. SGS was primarily due to clusters of young adults located along seasonal streams, rocky areas, and in abandoned pastures. SGS was highest in the first distance class in the least disturbed population, which also had the lowest density of large adults. Low, but significant SGS characterized the site with the highest number of large adults located in individual pastures. The semiurban site, had no clusters of young adults and, probably as a result, failed to exhibit SGS. Our results demonstrate that disturbance can strongly influence SGS patterns and are consistent with a landscape model in which the location of potential recruitment sites, restricted seed disperser movements, and the number and location of maternal individuals dictate the level and pattern of SGS.

Determination of atomic vacancies in InAs/GaSb strained-layer superlattices by atomic strain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Honggyu; Meng, Yifei; Kwon, Ji-Hwan

Determining vacancy in complex crystals or nanostructures represents an outstanding crystallographic problem that has a large impact on technology, especially for semiconductors, where vacancies introduce defect levels and modify the electronic structure. However, vacancy is hard to locate and its structure is difficult to probe experimentally. Reported here are atomic vacancies in the InAs/GaSb strained-layer superlattice (SLS) determined by atomic-resolution strain mapping at picometre precision. It is shown that cation and anion vacancies in the InAs/GaSb SLS give rise to local lattice relaxations, especially the nearest atoms, which can be detected using a statistical method and confirmed by simulation. Themore » ability to map vacancy defect-induced strain and identify its location represents significant progress in the study of vacancy defects in compound semiconductors.« less

Determination of atomic vacancies in InAs/GaSb strained-layer superlattices by atomic strain

DOE PAGES

Kim, Honggyu; Meng, Yifei; Kwon, Ji-Hwan; ...

2018-01-01

Determining vacancy in complex crystals or nanostructures represents an outstanding crystallographic problem that has a large impact on technology, especially for semiconductors, where vacancies introduce defect levels and modify the electronic structure. However, vacancy is hard to locate and its structure is difficult to probe experimentally. Reported here are atomic vacancies in the InAs/GaSb strained-layer superlattice (SLS) determined by atomic-resolution strain mapping at picometre precision. It is shown that cation and anion vacancies in the InAs/GaSb SLS give rise to local lattice relaxations, especially the nearest atoms, which can be detected using a statistical method and confirmed by simulation. Themore » ability to map vacancy defect-induced strain and identify its location represents significant progress in the study of vacancy defects in compound semiconductors.« less

Holocene Indian Ocean Cosmic Impacts: The Megatsunami Chevron Evidence From Madagascar

NASA Astrophysics Data System (ADS)

Masse, W.; Bryant, E.; Gusiakov, V.; Abbott, D.; Rambolamana, G.; Raza, H.; Courty, M.; Breger, D.; Gerard-Little, P.; Burckle, L.

2006-12-01

The 2.6 million year Quaternary period terrestrial physical record lacks definitive crater evidence for major regional catastrophic impacts by asteroids and comets other than the 10.5-km diameter Botsumtwi structure in Ghana and the 14.0-km diameter Zhamanshin structure in Kazakhstan [1] dating between about 900 and 1100 kya. Current cosmic impact rate models suggest that an average of between 3-6 globally catastrophic impacts should have occurred on the Earth during the Quaternary, along with several additional significant regional impacts in addition to Zhamanshin and Botsumtwi. These models and data indicate that the great majority of the "missing" major impact locations would likely have occurred in poorly studied oceanic settings. Only recently have Late Quaternary and Holocene period coastal paleo-megatsunami chevron deposits been defined in the Caribbean and along the western coasts of Australia, along with the suggestion that some may have been created by oceanic cosmic impacts in distinction to those caused by landslips, eruptions, and seismic events. We investigate the possibility that many or most megatsunami chevrons occurring along the southern coast of Madagascar were caused by two or more major Holocene Indian Ocean cosmic impacts. This hypothesis is based on an initial study of the worldwide archaeological and anthropological record, and the preliminary study of satellite images of the chevrons, selected Indian Ocean deep-sea cores, sea-floor bathymetry, and physical examination of the Madagascar deposits themselves. Candidate Indian Ocean impact structures are identified and correlated with the southern Madagascar megatsunami chevron deposits. [1] Masse, W.B. 2007 The Archaeology and Anthropology of Quaternary Period Cosmic Impact. In Bobrowsky, P.T. & Rickman, H. (eds.)Comets/Asteroid Impacts and Human Society. Springer, Berlin (in press).

Lunar Impact Flash Locations

NASA Technical Reports Server (NTRS)

Moser, D. E.; Suggs, R. M.; Kupferschmidt, L.; Feldman, J.

2015-01-01

A bright impact flash detected by the NASA Lunar Impact Monitoring Program in March 2013 brought into focus the importance of determining the impact flash location. A process for locating the impact flash, and presumably its associated crater, was developed using commercially available software tools. The process was successfully applied to the March 2013 impact flash and put into production on an additional 300 impact flashes. The goal today: provide a description of the geolocation technique developed.

Hurricane impacts on forest resources in the Eastern United States: a post-sandy assessment

Treesearch

Greg C. Liknes; Susan J. Crocker; Randall S. Morin; Brian F. Walters

2015-01-01

Extreme weather events play a role in shaping the composition and structure of forests. Responding to and mitigating a storm event in a forested environment requires information about the location and severity of tree damage. However, this information can be difficult to obtain immediately following an event. Post-storm assessments using regularly collected forest...

Erosion of Perennially Frozen Streambanks,

DTIC Science & Technology

1983-12-01

erosional processes. Factors that determine rates and locations of erosion in- dude physical, thermal and structural properties of bank sediments , stream...Program, Environmental Impact, and Civil Works Work Unit CWIS 31722, Sediment Transport and Deposition in Northern Rivers; Research Area, Flood Control...between bank and bluff zones of eroding, perennially frozen streambanks 4 3. Cantilevered blocks of frozen sediment above thermoerosional niche, northern

Fire and fire surrogate study: annotated highlights from oak-dominated sites

Treesearch

Daniel A. Yaussy; Thomas A. Waldrop

2009-01-01

The National Fire and Fire Surrogate (FFS) study was implemented to investigate the ecological impacts of prescribed fire and mechanical operations to mimic fire in restoring the structure and function of forests typically maintained by frequent, low-intensity fires. Two of the 12 sites were located in oak-dominated forests, one in Ohio and another in North Carolina....

Using structure locations as a basis for mapping the wildland urban interface

Treesearch

Avi Bar-Massada; Susan I. Stewart; Roger B. Hammer; Miranda H. Mockrin; Volker C. Radeloff

2013-01-01

The wildland urban interface (WUI) delineates the areas where wildland fire hazard most directly impacts human communities and threatens lives and property, and where houses exert the strongest influence on the natural environment. Housing data are a major problem for WUI mapping. When housing data are zonal, the concept of a WUI neighborhood can be captured easily in...

In vitro attenuation of impact shock in equine digits.

PubMed

Lanovaz, J L; Clayton, H M; Watson, L G

1998-09-01

This study was designed to test the impact characteristics of the equine digit in vitro with the objective of providing a better understanding of the role of the digital structures in the attenuation of impact shock. Uni-axial accelerometers were mounted on cadaver digits on the distolateral hoof wall, the proximolateral hoof wall, the dorsal surface of the second phalanx, and the mid-lateral first phalanx. The hoof-mounted accelerometers were aligned with the hoof tubules while the bone-mounted accelerometers were oriented along the longitudinal axis of the bone. Each digit was mounted in a test apparatus designed to simulate impact of the hoof with the ground during locomotion. The digits were subjected to 3 impact trials against a barrier at each of 3 vertical impact velocities that simulated a forward trotting velocity in the range of 2.67 to 4.46 m/s. The impact deceleration tended to increase with impact velocity. Attenuation of the impact shock by the digital tissues resulted in a reduction in impact decleration in the more proximal measuring locations. The interphalangeal joints appeared to play a larger role in amplitude attenuation than the hoof wall or the soft tissue structures within the hoof wall. The signal frequency data showed that the soft tissues within the hoof acted as a 'lowpass' filter, attenuating the higher deceleration frequencies. The hoof wall and the interphalangeal joints showed little frequency attenuation.

Contemporary State of the Elbrus Volcanic Center (The Northern Caucasus)

NASA Astrophysics Data System (ADS)

Milyukov, Vadim; Rogozhin, Eugeny; Gorbatikov, Andrey; Mironov, Alexey; Myasnikov, Andrey; Stepanova, Marina

2018-05-01

The Elbrus volcanic center is located in southern Russia on the northern slope of the main ridge of the Greater Caucasus. Current classifications define Elbrus as a dormant volcano that could become active even after millennia of quiescence. In this study, we use two new geophysical methods to assess the contemporary state of the Elbrus volcano. The first method is based on an evaluation of parameters of resonant modes "reemitted" by the resonant structure (i.e., volcanic chamber) in response to the excitation of a seismic impact and recorded by a precise laser interferometer-strainmeter. The second method is based on low-frequency microseismic sounding and allows determination of the deep structure of complicated geological objects. Our study locates the magma chamber at depths of 1-8 km and extended magma source at depths of 15-40 km beneath the Elbrus eastern summit. An unknown magmatic structure, comparable to the Elbrus magmatic structure but currently much colder, was also identified 50 km from Mt. Elbrus. Based on our analysis, we assess the Elbrus volcano to be currently in a quasi-stable state of thermodynamic equilibrium.

Crystal structures of ryanodine receptor SPRY1 and tandem-repeat domains reveal a critical FKBP12 binding determinant

NASA Astrophysics Data System (ADS)

Yuchi, Zhiguang; Yuen, Siobhan M. Wong King; Lau, Kelvin; Underhill, Ainsley Q.; Cornea, Razvan L.; Fessenden, James D.; van Petegem, Filip

2015-08-01

Ryanodine receptors (RyRs) form calcium release channels located in the membranes of the sarcoplasmic and endoplasmic reticulum. RyRs play a major role in excitation-contraction coupling and other Ca2+-dependent signalling events, and consist of several globular domains that together form a large assembly. Here we describe the crystal structures of the SPRY1 and tandem-repeat domains at 1.2-1.5 Å resolution, which reveal several structural elements not detected in recent cryo-EM reconstructions of RyRs. The cryo-EM studies disagree on the position of SPRY domains, which had been proposed based on homology modelling. Computational docking of the crystal structures, combined with FRET studies, show that the SPRY1 domain is located next to FK506-binding protein (FKBP). Molecular dynamics flexible fitting and mutagenesis experiments suggest a hydrophobic cluster within SPRY1 that is crucial for FKBP binding. A RyR1 disease mutation, N760D, appears to directly impact FKBP binding through interfering with SPRY1 folding.

Blacktip reef sharks, Carcharhinus melanopterus, have high genetic structure and varying demographic histories in their Indo-Pacific range.

PubMed

Vignaud, Thomas M; Mourier, Johann; Maynard, Jeffrey A; Leblois, Raphael; Spaet, Julia; Clua, Eric; Neglia, Valentina; Planes, Serge

2014-11-01

For free-swimming marine species like sharks, only population genetics and demographic history analyses can be used to assess population health/status as baseline population numbers are usually unknown. We investigated the population genetics of blacktip reef sharks, Carcharhinus melanopterus; one of the most abundant reef-associated sharks and the apex predator of many shallow water reefs of the Indian and Pacific Oceans. Our sampling includes 4 widely separated locations in the Indo-Pacific and 11 islands in French Polynesia with different levels of coastal development. Four-teen microsatellite loci were analysed for samples from all locations and two mitochondrial DNA fragments, the control region and cytochrome b, were examined for 10 locations. For microsatellites, genetic diversity is higher for the locations in the large open systems of the Red Sea and Australia than for the fragmented habitat of the smaller islands of French Polynesia. Strong significant structure was found for distant locations with FST values as high as ~0.3, and a smaller but still significant structure is found within French Polynesia. Both mitochondrial genes show only a few mutations across the sequences with a dominant shared haplotype in French Polynesia and New Caledonia suggesting a common lineage different to that of East Australia. Demographic history analyses indicate population expansions in the Red Sea and Australia that may coincide with sea level changes after climatic events. Expansions and flat signals are indicated for French Polynesia as well as a significant recent bottleneck for Moorea, the most human-impacted lagoon of the locations in French Polynesia. © 2014 John Wiley & Sons Ltd.

3D gravimetric investigation of the Cerro do Jarau structure, Rio Grande do Sul, Brazil

NASA Astrophysics Data System (ADS)

Giacomini, Bruno B.; Leite, Emilson P.; Crósta, Alvaro P.

2017-04-01

The Cerro do Jarau structure is possibly the third Brazilian basaltic crater formed in continental flood basalt of the Serra Geral Formation, Paraná Basin, a large igneous province (LIP) in southern Brazil. It is a nearly circular landform with a diameter of approximately 13 km that rises 200 m above the plains of the "pampas" in southern Brazil. In this work, Bouguer anomalies were calculated from gravity accelerations measured on the area of this structure. The residual Bouguer map shows a strong positive anomaly trending NE-SW, located in the northeastern part of the structure, a feature not commonly associated with impact structures. However, the negative anomaly present in its center and the circular positive anomaly surrounding the central portion are typical of impact structures. The residual Bouguer anomaly varies from -2 mGal to 8 mGal. The positive circular anomaly is not spatially coincident with the rim of the structure. Based on the interpretation of our gravimetric data, the estimated diameter of the structure is 12 km and the central portion has a diameter of approximately 5 km, both slightly smaller than previously suggested. The Bouguer anomaly map was inverted into a 3D density model using a constrained inversion method with a maximum density contrast of 0.5 g cm-3. This model was interpreted to associate densities with rock types, resulting in a geological model. This geological model is in accordance with the meteorite impact nature of Cerro do Jarau.

Formation of the Orientale lunar multiring basin.

PubMed

Johnson, Brandon C; Blair, David M; Collins, Gareth S; Melosh, H Jay; Freed, Andrew M; Taylor, G Jeffrey; Head, James W; Wieczorek, Mark A; Andrews-Hanna, Jeffrey C; Nimmo, Francis; Keane, James T; Miljković, Katarina; Soderblom, Jason M; Zuber, Maria T

2016-10-28

Multiring basins, large impact craters characterized by multiple concentric topographic rings, dominate the stratigraphy, tectonics, and crustal structure of the Moon. Using a hydrocode, we simulated the formation of the Orientale multiring basin, producing a subsurface structure consistent with high-resolution gravity data from the Gravity Recovery and Interior Laboratory (GRAIL) spacecraft. The simulated impact produced a transient crater, ~390 kilometers in diameter, that was not maintained because of subsequent gravitational collapse. Our simulations indicate that the flow of warm weak material at depth was crucial to the formation of the basin's outer rings, which are large normal faults that formed at different times during the collapse stage. The key parameters controlling ring location and spacing are impactor diameter and lunar thermal gradients. Copyright © 2016, American Association for the Advancement of Science.

Using PVDF to locate the debris cloud impact position

NASA Astrophysics Data System (ADS)

Pang, Baojun; Liu, Zhidong

2010-03-01

With the increase of space activities, space debris environment has deteriorated. Space debris impact shields of spacecraft creates debris cloud, the debris cloud is a threat to module wall. In order to conduct an assessment of spacecraft module wall damage impacted by debris cloud, the damage position must be known. In order to design a light weight location system, polyvinylidene fluoride (PVDF) has been studied. Hyper-velocity impact experiments were conducted using two-stage light gas gun, the experimental results indicate that: the virtual wave front location method can be extended to debris cloud impact location, PVDF can be used to locate the damage position effectively, the signals gathered by PVDF from debris cloud impact contain more high frequency components than the signals created by single projectile impact event. The results provide a reference for the development of the sensor systems to detect impacts on spacecraft.

Performances of different global positioning system devices for time-location tracking in air pollution epidemiological studies.

PubMed

Wu, Jun; Jiang, Chengsheng; Liu, Zhen; Houston, Douglas; Jaimes, Guillermo; McConnell, Rob

2010-11-23

People's time-location patterns are important in air pollution exposure assessment because pollution levels may vary considerably by location. A growing number of studies are using global positioning systems (GPS) to track people's time-location patterns. Many portable GPS units that archive location are commercially available at a cost that makes their use feasible for epidemiological studies. We evaluated the performance of five portable GPS data loggers and two GPS cell phones by examining positional accuracy in typical locations (indoor, outdoor, in-vehicle) and factors that influence satellite reception (building material, building type), acquisition time (cold and warm start), battery life, and adequacy of memory for data storage. We examined stationary locations (eg, indoor, outdoor) and mobile environments (eg, walking, traveling by vehicle or bus) and compared GPS locations to highly-resolved US Geological Survey (USGS) and Digital Orthophoto Quarter Quadrangle (DOQQ) maps. The battery life of our tested instruments ranged from <9 hours to 48 hours. The acquisition of location time after startup ranged from a few seconds to >20 minutes and varied significantly by building structure type and by cold or warm start. No GPS device was found to have consistently superior performance with regard to spatial accuracy and signal loss. At fixed outdoor locations, 65%-95% of GPS points fell within 20-m of the corresponding DOQQ locations for all the devices. At fixed indoor locations, 50%-80% of GPS points fell within 20-m of the corresponding DOQQ locations for all the devices except one. Most of the GPS devices performed well during commuting on a freeway, with >80% of points within 10-m of the DOQQ route, but the performance was significantly impacted by surrounding structures on surface streets in highly urbanized areas. All the tested GPS devices had limitations, but we identified several devices which showed promising performance for tracking subjects' time location patterns in epidemiological studies.

Performances of Different Global Positioning System Devices for Time-Location Tracking in Air Pollution Epidemiological Studies

PubMed Central

Wu, Jun; Jiang, Chengsheng; Liu, Zhen; Houston, Douglas; Jaimes, Guillermo; McConnell, Rob

2010-01-01

Background: People’s time-location patterns are important in air pollution exposure assessment because pollution levels may vary considerably by location. A growing number of studies are using global positioning systems (GPS) to track people’s time-location patterns. Many portable GPS units that archive location are commercially available at a cost that makes their use feasible for epidemiological studies. Methods: We evaluated the performance of five portable GPS data loggers and two GPS cell phones by examining positional accuracy in typical locations (indoor, outdoor, in-vehicle) and factors that influence satellite reception (building material, building type), acquisition time (cold and warm start), battery life, and adequacy of memory for data storage. We examined stationary locations (eg, indoor, outdoor) and mobile environments (eg, walking, traveling by vehicle or bus) and compared GPS locations to highly-resolved US Geological Survey (USGS) and Digital Orthophoto Quarter Quadrangle (DOQQ) maps. Results: The battery life of our tested instruments ranged from <9 hours to 48 hours. The acquisition of location time after startup ranged from a few seconds to >20 minutes and varied significantly by building structure type and by cold or warm start. No GPS device was found to have consistently superior performance with regard to spatial accuracy and signal loss. At fixed outdoor locations, 65%–95% of GPS points fell within 20-m of the corresponding DOQQ locations for all the devices. At fixed indoor locations, 50%–80% of GPS points fell within 20-m of the corresponding DOQQ locations for all the devices except one. Most of the GPS devices performed well during commuting on a freeway, with >80% of points within 10-m of the DOQQ route, but the performance was significantly impacted by surrounding structures on surface streets in highly urbanized areas. Conclusions: All the tested GPS devices had limitations, but we identified several devices which showed promising performance for tracking subjects’ time location patterns in epidemiological studies. PMID:21151593

Effect of low-speed impact damage and damage location on behavior of composite panels

NASA Technical Reports Server (NTRS)

Jegley, Dawn C.

1992-01-01

The effect of low speed impact damage on the compression and tension strength of thin and moderately thick composite specimens was investigated. Impact speed ranged from 50 to 550 ft./sec., with corresponding impact energies from 0.25 to 30.7 ft. x lb. Impact locations were near the center of the specimen or near a lateral unloaded edge. In this study, thin specimens with only 90 degree and + or - 45 degree plies that were impacted away from the unloaded edge suffered less reduction in load carrying capability because of impact damage than of the same specimens impacted near the unloaded edge. Failure loads of thicker compression loaded specimens with a similar stacking sequence were independent of impact location. Failure loads of thin tension loaded specimens with 0 degree plies was independent of impact location, whereas failure loads of thicker compression loaded specimens with 0 degree plies were dependent upon impact location. A finite element analysis indicated that high axial strains occurred near the unloaded edges of the postbuckled panels. Thus, impacts near the unloaded edge would significantly affect the behavior of the postbuckled panel.

The first description and confirmation of the Vista Alegre impact structure in the Paraná flood basalts of southern Brazil

NASA Astrophysics Data System (ADS)

Crósta, Alvaro P.; Koeberl, Christian; Furuie, Rafael A.; Kazzuo-Vieira, Cesar

2010-02-01

The Vista Alegre structure, centered at 25°57'S and 52°41'W, has been recently proposed as a meteorite impact structure. The 9.5km-diameter structure is located in the Paraná state of southern Brazil, within the Paraná Basin, which contains one of the largest and most extensive flood basalt provinces on Earth. The Paraná flood basalts belong to the Serra Geral Formation and are temporally related to the opening of the South Atlantic Ocean, having been dated at about 133-132Ma. Tholeiitic basalts dominate the western portion of Paraná state, with some minor rhyodacites. Morphologically, Vista Alegre has a prominent circular outline, in the form of an incomplete ring of escarpments, and an inner depression. The presence of a central uplift is not obvious, but it is inferred by the occurrence of deformed sandstone blocks near the center of the structure. These sandstones are possibly related to the Triassic Pirambóia Formation and/or to the Cretaceous Botucatu Formation. These units are normally at stratigraphic depths of about 700-800m below the present surface in this portion of the Paraná Basin. The structure appears to be in an advanced erosion stage and its interior is occupied by a soil cover several meters thick, extensively used for agriculture. As a result there are limited outcrops in the interior of the structure, all of polymict breccias, some of them melt-bearing. We report the extensive occurrence of shatter cones, in the form of fine-grained rock clasts within the polymict breccias. The shatter cone-bearing breccias occur at different locations within the structure, separated by several kilometers. The nested shatter cones range in size from about 0.5 to 20cm for individual cones, and up to half a meter for complete assemblages. The shatter cones formed in fine-grained Parana flood basalt and might be the first examples of shatter cones in such a rock type. In addition, planar deformation features (PDFs) were found in quartz grains within sedimentary rock clasts of the polymict breccia. These findings confirm the impact origin of the Vista Alegre structure.

Impact of Non-Native Birds on Native Ecosystems: A Global Analysis.

PubMed

Martin-Albarracin, Valeria L; Amico, Guillermo C; Simberloff, Daniel; Nuñez, Martin A

2015-01-01

Introduction and naturalization of non-native species is one of the most important threats to global biodiversity. Birds have been widely introduced worldwide, but their impacts on populations, communities, and ecosystems have not received as much attention as those of other groups. This work is a global synthesis of the impact of nonnative birds on native ecosystems to determine (1) what groups, impacts, and locations have been best studied; (2) which taxonomic groups and which impacts have greatest effects on ecosystems, (3) how important are bird impacts at the community and ecosystem levels, and (4) what are the known benefits of nonnative birds to natural ecosystems. We conducted an extensive literature search that yielded 148 articles covering 39 species belonging to 18 families -18% of all known naturalized species. Studies were classified according to where they were conducted: Africa, Asia, Australasia, Europe, North America, South America, Islands of the Indian, of the Pacific, and of the Atlantic Ocean. Seven types of impact on native ecosystems were evaluated: competition, disease transmission, chemical, physical, or structural impact on ecosystem, grazing/ herbivory/ browsing, hybridization, predation, and interaction with other non-native species. Hybridization and disease transmission were the most important impacts, affecting the population and community levels. Ecosystem-level impacts, such as structural and chemical impacts were detected. Seven species were found to have positive impacts aside from negative ones. We provide suggestions for future studies focused on mechanisms of impact, regions, and understudied taxonomic groups.

New Clues on the Source of the Central Magnetic Anomaly at Haughton Impact Structure, Canada

NASA Astrophysics Data System (ADS)

Quesnel, Y.; Rochette, P.; Gattacceca, J.; Osinski, G. R.

2013-12-01

The 23 km-diameter Haughton impact structure, located on Devon Island, Nunavut, Canada, is one of the best-preserved medium-size complex impact structures on Earth. The impact occurred ~39 Ma ago into a target formation composed of an ~2-km thick sequence of Lower Paleozoic sedimentary rocks of the Arctic Platform overlying Precambrian metamorphic basement of the Canadian Shield (Osinski et al., 2005). Clast-rich carbonate impact melt rocks fill the crater and impact-generated hydrothermal activity took place, but since then no significant geological event has affected the area. A 900 nT-amplitude magnetic anomaly with a wavelength of about 3 km is observed at the center of the crater (Pohl et al., 1988). Using high-resolution ground magnetic survey and magnetic property measurements on rock samples from inside and outside the structure, Quesnel et al. (2013) concluded that the source for this anomaly may correspond to uplifted and hydrothermally-aletered basement rocks. Hydrothermal activity can increase rock magnetization intensity by crystallization of magnetic minerals, such as magnetite and/or pyrrhotite. Here, we present the results of a new ground magnetic survey and electrical resistivity soundings conducted around the maximum of the magnetic anomaly. Drilling, with depths ranging from 5 m to 13 m was also conducted at three locations in the same area to ground truth the interpretation of geophysical data. The maximum of the magnetic anomaly is characterized by a ~50 m2 area of strong vertical magnetic gradient and low electrical resistivity, while the surroundings show weak gradient and large resistivity. Two drill holes into this localized area show about 6 m of sandy material with some more magnetic layers at about 5 m depth overlying a greenish impact melt breccia with very abundant and large clasts. Recovery in the first 9 meters is very poor, but down hole magnetic gradient measurement confirms the near 6 meter magnetic layer. A third hole was drilled outside the local area with strong magnetic gradients and shows, starting at 2 m depth a porous gray clast-rich impact melt rock that is very similar to the impact melt rock extensively cropping out in the crater. Therefore, the three drill holes confirm that the geophysical contrast at the crater center corresponds to a geological contrast and suggest a link with hydrothermal activity. The results of laboratory measurements (magnetic properties in particular) made on the drill cores will also be presented. References : Osinski, G. R. et al. 2005. MPS, 40:1759-1776 ; Pohl, J. et al. 1988. Meteoritics, 23:235-238 ; Quesnel, Y. et al. 2013. EPSL, 367:116-122.

SPH Simulation of Impact of a Surge on a Wall

NASA Astrophysics Data System (ADS)

Diwakar, Manoj Kumar; Mohapatra, Pranab Kumar; Tripathi, Shivam

2014-05-01

Structures located on the downstream of a dam are prone to impact of the surge due to dam break flow. Ramsden (1996) experimentally studied the run-up height on a vertical wall due to propagation of bore and surge on dry bed and measured their impact on the wall. Mohapatra et al. (2000) applied Navier Stokes equations to numerically study the impact of bore on vertical and inclined walls. They also obtained the evolution of surge on dry bed. In the present work, the impact of a surge wave due to dam break flow against the wall is modeled with a two-dimensional smoothed particle hydrodynamics (SPH) model. SPH is a mesh-free method that relies on the particle view of the field problem and approximates the continuity and momentum equations on a set of particles. The method solves the strong form of Navier-Stokes equations. The governing equations are solved numerically in the vertical plane. The propagation of the surge wave, its impact and the maximum run-up on the wall located at the boundary are analyzed. Surface profile, velocity field and pressure distributions are simulated. Non-dimensional run-up height obtained from the present numerical model is 0.86 and is in good agreement with the available experimental data of Ramsden (1996) which is in the range of 0.75-0.9. Also, the simulated profile of the surge tip was comparable to the empirical equations refereed in Ramsden (1996). The model is applied to the study the maximum force and the run-up height on inclined walls with different inclinations. The results indicate that the maximum force and the run-up height on the wall increase with the increment of wall inclination. Comparison of numerical results with analytical solutions derived from shallow water equations clearly shows the breakdown of shallow water assumption during the impact. In addition to these results, the numerical simulation yields the complete velocity and pressure ?elds which may be used to design structures located in the path of a dam-break wave. The study shows that the smoothed particle hydrodynamics can effectively simulate fluid flow dynamics. References: Mohapatra, P. K., Bhallamudi, S. M., and Eswaran, V. (2000). 'Numerical simulation of impact of bores against inclined walls.' J. Hydraulic. Engg., ASCE, 126(12), 942-945. Ramsden, J. D. (1996). 'Forces on a vertical wall due to long waves, bores, and dry-bed surges.' J. Waterway, Port, Coastal, and Ocean Engg., ASCE, 122(3), 134-141.

Importance of geologic study and load test of log pod mangartom arch bridge

NASA Astrophysics Data System (ADS)

Kamnik, Rok; Meshcheryakova, Tatiana; Kovačič, Boštjan

2017-10-01

Some structures and their relationships, positions in space and shifts represent the structural set of an area, as included within regional units, and smaller or larger portions of the earth’s crust known as the Earth’s plates and micro plates. The most important fact is that tectonic movements are always possible around the locations of considered bridges. Therefore, it is certainly necessary to define in detail their characteristics due to the potential impacts on individual bridges. A recent structural set was made for the Log pod Mangartom. To assess the bridge in micro sense the load test of the bridge was performed.

Comparison of head impact location during games and practices in Division III men's lacrosse players.

PubMed

O'Day, Kathleen M; Koehling, Elizabeth M; Vollavanh, Lydia R; Bradney, Debbie; May, James M; Breedlove, Katherine M; Breedlove, Evan L; Blair, Price; Nauman, Eric A; Bowman, Thomas G

2017-03-01

Head impacts have been studied extensively in football, but little similar research has been conducted in men's lacrosse. It is important to understand the location and magnitude of head impacts during men's lacrosse to recognize the risk of head injury. Descriptive epidemiology study set on collegiate lacrosse fields. Eleven men's lacrosse players (age=20.9±1.13years, mass=83.91±9.04kg, height=179.88±5.99cm) volunteered to participate. We applied X2 sensors behind the right ear of participants for games and practices. Sensors recorded data on linear and rotational accelerations and the location of head impacts. We calculated incidence rates per 1000 exposures with 95% confidence intervals for impact locations and compared the effect of impact location on linear and rotational accelerations with Kruskal-Wallis tests. We verified 167 head impacts (games=112; practices=55). During games, the incidence rate was 651.16 (95% confidence interval=530.57-771.76). The high and low incidence rates for head impact locations during games were: side=410.7 (95% confidence interval=292.02-529.41) and top=26.79 (95% confidence interval=3.53-57.10). For games and practices combined, the impact locations did not significantly affect linear (χ 2 3 =6.69, P=0.08) or rotational acceleration (χ 2 3 =6.34, P=0.10). We suggest further research into the location of head impacts during games and practices. We also suggest player and coach education on head impacts as well as behavior modification in men's lacrosse athletes to reduce the incidence of impacts to the side of the head in an effort to reduce potential injury. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterizing backcountry camping impacts in Great Smoky Mountains National Park

USGS Publications Warehouse

Leung, Y.-F.; Marion, J.L.

1999-01-01

This investigates resource impacts on backcounty campsites in the Great Smoky Mountains National Park, USA. Study objectives were to enhance our understanding of camping impacts and to improve campsite impact assessment procedures by means of multivariate techniques. Three-hundred and eight campsites at designated backcountry campgrounds, and 69 additional unofficial campsites were assessed. Factor analysis of 195 established campsites on eight impact indicator variables revealed three dimensions of campsite impact: area disturbance, soil and groundcover damage, and tree-related damage. Four distinctive backcountry campsite types were identified, three of which were derived from cluster analyses of factor scores. These four backcountry campsite types characterize the intensity and areal extent of resource impacts, and they vary in locational and environmental attributes. At an aggregate level, different campsite types contributed unequally to the cumulative level of impact. The dimensional structure and typology developed in this study demonstrates that campsite impacts can be viewed and examined holistically with the use of multivariate methods. Implications for assessment procedures, management and further research are discussed.

Expansion analyses of strategic petroleum reserve in Bayou Choctaw : revised locations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ehgartner, Brian L.; Park, Byoung Yoon

2010-11-01

This report summarizes a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by changing the locations of two caverns. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure, and well integrity are quantified.more » Two scenarios were used for the duration and timing of workover conditions where wellhead pressures are temporarily reduced to atmospheric pressure. The three expansion caverns are predicted to be structurally stable against tensile failure for both scenarios. Dilatant failure is not expected within the vicinity of the expansion caverns. Damage to surface structures is not predicted and there is not a marked increase in surface strains due to the presence of the three expansion caverns. The wells into the caverns should not undergo yield. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.« less

Impact of soil structure heterogeneity on the degradation of organic pollutants at the centimeter scale : 3D Modeling using graph based method

NASA Astrophysics Data System (ADS)

Sinclair Yemini, Francis; Chenu, Claire; Monga, Olivier; Vieuble Gonond, Laure; Juarez, Sabrina; Pihneiro, Marc; otten, Wilfred; Garnier, Patricia

2014-05-01

Contaminant degradation by microorganisms is very variable in soils because of the very heterogeneous spatial relationship of contaminant/degraders. Repacked Soil columns were carried out to study the degradation of 2,4D pesticide labelled with C14 for different scenarios of microorganisms and pesticide initial location. Measurements of global C14-CO2 emission and C14 distribution in the soil column showed that the initial location play a crucial rule on the dissipation of the pollutant. Experiments were simulated using a 3D model able to model microbial degradation and substrate diffusion between aggregates by considering explicitly the 3D structure of soil from CT images. The initial version of the model (Monga et al., 2008) was improved in order to simulate diffusion in samples of large size. Partial differential equations were implemented using freefem++ solver. The model simulates properly the dynamics of 2,4D in the column for the different initial situations. CT images of the same soil but using undisturbed structure instead of repacked aggregates were also carried out. Significant differences of the simulated results were observed between the repacked and the undisturbed soil. The conclusion of our work is that the heterogeneity of the soil structure and location of pollutants and decomposers has a very strong influence on the dissipation of pollutants.

Locating the LCROSS Impact Craters

NASA Technical Reports Server (NTRS)

Marshall, William; Shirley, Mark; Moratto, Zachary; Colaprete, Anthony; Neumann, Gregory A.; Smith, David E.; Hensley, Scott; Wilson, Barbara; Slade, Martin; Kennedy, Brian;

How does the interaction of presumed timing, location and extent of the underlying brain lesion relate to upper limb function in children with unilateral cerebral palsy?

PubMed

Mailleux, Lisa; Klingels, Katrijn; Fiori, Simona; Simon-Martinez, Cristina; Demaerel, Philippe; Locus, Marlies; Fosseprez, Eva; Boyd, Roslyn N; Guzzetta, Andrea; Ortibus, Els; Feys, Hilde

2017-09-01

Upper limb (UL) function in children with unilateral cerebral palsy (CP) vary largely depending on presumed timing, location and extent of brain lesions. These factors might exhibit a complex interaction and the combined prognostic value warrants further investigation. This study aimed to map lesion location and extent and assessed whether these differ according to presumed lesion timing and to determine the impact of structural brain damage on UL function within different lesion timing groups. Seventy-three children with unilateral CP (mean age 10 years 2 months) were classified according to lesion timing: malformations (N = 2), periventricular white matter (PWM, N = 42) and cortical and deep grey matter (CDGM, N = 29) lesions. Neuroanatomical damage was scored using a semi-quantitative MRI scale. UL function was assessed at body function and activity level. CDGM lesions were more pronounced compared to PWM lesions (p = 0.0003). Neuroanatomical scores were correlated with a higher degree to UL function in the CDGM group (r s  = -0.39 to r s  = -0.84) compared to the PWM group (r rb  = -0.42 to r s  = -0.61). Regression analysis found lesion location and extent to explain 75% and 65% (p < 0.02) respectively, of the variance in AHA performance in the CDGM group, but only 24% and 12% (p < 0.03) in the PWM group. In the CDGM group, lesion location and extent seems to impact more on UL function compared to the PWM group. In children with PWM lesions, other factors like corticospinal tract (re)organization and structural connectivity may play an additional role. Copyright © 2017 European Paediatric Neurology Society. All rights reserved.

3D Thermal and Electrochemical Model for Spirally Wound Large Format Lithium-ion Batteries (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, K. J.; Kim, G. H.; Smith, K.

In many commercial cells, long tabs at both cell sides, leading to uniform potentials along the spiral direction of wound jelly rolls, are rarely seen because of their high manufacturing cost. More often, several metal strips are welded at discrete locations along both current collector foils. With this design, the difference of electrical potentials is easily built up along current collectors in the spiral direction. Hence, the design features of the tabs, such as number, location and size, can be crucial factors for spiral-shaped battery cells. This paper presents a Li-ion battery cell model having a 3-dimensional spiral mesh involvingmore » a wound jellyroll structure. Further results and analysis will be given regarding impacts of tab location, number, and size.« less

Accelerations and Passenger Harness Loads Measured in Full-Scale Light-Airplane Crashes

NASA Technical Reports Server (NTRS)

Eiband, A. Martin; Simpkinson, Scott H.; Black, Dugald O.

1953-01-01

Full-scale light-airplane crashes simulating stall-spin accidents were conducted to determine the decelerations to which occupants are exposed and the resulting harness forces encountered in this type of accident. Crashes at impact speeds from 42 to 60 miles per hour were studied. The airplanes used were of the familiar steel-tube, fabric-covered, tandem, two-seat type. In crashes up to an impact speed of 60 miles per hour, crumpling of the forward fuselage structure prevented the maximum deceleration at the rear-seat location from exceeding 26 to 33g. This maximum g value appeared independent of the impact speed. Restraining forces in the seatbelt - shoulder-harness combination reached 5800 pounds. The rear-seat occupant can survive crashes of the type studied at impact speeds up to 60 miles per hour, if body movement is restrained by an adequate seatbelt-shoulder-harness combination so as to prevent injurious contact with obstacles normally present in the cabin. Inwardly collapsing cabin structure, however, is a potential hazard in the higher-speed crashes.

Urban retail location: Insights from percolation theory and spatial interaction modeling

PubMed Central

Molinero, Carlos; Wilson, Alan

2017-01-01

Characterising road networks has been the focus of a large body of research due to it being the main driver of activities in an urban ecosystem and the structuring factor in the dynamics of the city. One of these activities, and one with the largest economical impact in a city, is retail dynamics and its evolution. Therefore, the mathematical modeling of the location of retail activities and of the emergence of clustering in retail centers has as well generated a large number of works. Despite these two interwoven components strongly depending on one another and their fundamental importance in understanding cities, little work has been done in order to compare their local and global properties. Here we compare the road network’s hierarchical structure, unveiled through a percolation analysis of the network, with the retail location distribution defined by exploiting a gravity-based retail model. We interpret the great agreement in the city’s organizations as it emerges from both methodologies as new evidence of the interdependence of these two crucial dimensions of a city’s life. PMID:28977032

Urban retail location: Insights from percolation theory and spatial interaction modeling.

PubMed

Piovani, Duccio; Molinero, Carlos; Wilson, Alan

2017-01-01

Characterising road networks has been the focus of a large body of research due to it being the main driver of activities in an urban ecosystem and the structuring factor in the dynamics of the city. One of these activities, and one with the largest economical impact in a city, is retail dynamics and its evolution. Therefore, the mathematical modeling of the location of retail activities and of the emergence of clustering in retail centers has as well generated a large number of works. Despite these two interwoven components strongly depending on one another and their fundamental importance in understanding cities, little work has been done in order to compare their local and global properties. Here we compare the road network's hierarchical structure, unveiled through a percolation analysis of the network, with the retail location distribution defined by exploiting a gravity-based retail model. We interpret the great agreement in the city's organizations as it emerges from both methodologies as new evidence of the interdependence of these two crucial dimensions of a city's life.

Low-power triggered data acquisition system and method

NASA Technical Reports Server (NTRS)

Champaigne, Kevin (Inventor); Sumners, Jonathan (Inventor)

2012-01-01

A low-power triggered data acquisition system and method utilizes low-powered circuitry, comparators, and digital logic incorporated into a miniaturized device interfaced with self-generating transducer sensor inputs to detect, identify and assess impact and damage to surfaces and structures wherein, upon the occurrence of a triggering event that produces a signal greater than a set threshold changes the comparator output and causes the system to acquire and store digital data representative of the incoming waveform on at least one triggered channel. The sensors may be disposed in an array to provide triangulation and location of the impact.

29 CFR 1928.53 - Protective enclosures for wheel-type agricultural tractors-test procedures and performance...

Code of Federal Regulations, 2013 CFR

2013-07-01

... accomplished by using a 4,410-lb (2,000-kg) weight acting as a pendulum. The impact face of the weight shall be... of the pendulum will swing, or alternatively, two sets of symmetrically located cables may be used at... from the rear, followed by a load to the side on the same enclosure structure. The pendulum swinging...

29 CFR 1928.53 - Protective enclosures for wheel-type agricultural tractors-test procedures and performance...

Code of Federal Regulations, 2010 CFR

2010-07-01

... accomplished by using a 4,410-lb (2,000-kg) weight acting as a pendulum. The impact face of the weight shall be... of the pendulum will swing, or alternatively, two sets of symmetrically located cables may be used at... from the rear, followed by a load to the side on the same enclosure structure. The pendulum swinging...

29 CFR 1928.53 - Protective enclosures for wheel-type agricultural tractors-test procedures and performance...

Code of Federal Regulations, 2014 CFR

2014-07-01

...,000-kg) weight acting as a pendulum. The impact face of the weight shall be 27 ±1 in. by 27 ±1 in... restraining cables shall be located in the plane in which the center of gravity of the pendulum will swing, or... side on the same enclosure structure. The pendulum swinging from the height determined by paragraph (d...

29 CFR 1928.53 - Protective enclosures for wheel-type agricultural tractors-test procedures and performance...

Code of Federal Regulations, 2012 CFR

2012-07-01

... accomplished by using a 4,410-lb (2,000-kg) weight acting as a pendulum. The impact face of the weight shall be... of the pendulum will swing, or alternatively, two sets of symmetrically located cables may be used at... from the rear, followed by a load to the side on the same enclosure structure. The pendulum swinging...

29 CFR 1928.53 - Protective enclosures for wheel-type agricultural tractors-test procedures and performance...

Code of Federal Regulations, 2011 CFR

2011-07-01

... accomplished by using a 4,410-lb (2,000-kg) weight acting as a pendulum. The impact face of the weight shall be... of the pendulum will swing, or alternatively, two sets of symmetrically located cables may be used at... from the rear, followed by a load to the side on the same enclosure structure. The pendulum swinging...

Literacy Gets "a" Makeover: Engaged Learning Boosts Student Achievement at Michigan High School

ERIC Educational Resources Information Center

Wood, Richard E.; Burz, Helen L.

2013-01-01

E.A. Johnson High School is located in Mt. Morris, Michigan, near Flint, where the city has felt deeply the impact of the area's economic decline. 72% of the student population qualify for free and reduced lunch. The staff was willing to make the changes necessary for success, but needed more than a book study. Many of the structures for…

Development of an Automated Impact Hammer for Modal Analysis of Structures

DTIC Science & Technology

2012-02-01

6 3.5 Integration with FBG interrogation system . . . . . . . . . . . . . . . . . 7 4 Experimental...distributed Fibre Bragg Gratings ( FBGs ) in optical fibres. The modified approach to SIDER has been given the name iSIDER or inverse SIDER to reflect the...response is measured at many locations using a large array of surface mounted FBG strain sensors [2]. FBGs are ideally suited to the roving response approach

Weaving Action Learning into the Fabric of Manufacturing: The Impact of Humble Inquiry and Structured Reflection in a Cross-Cultural Context

ERIC Educational Resources Information Center

Luckman, Elizabeth A.

2017-01-01

This account of practice examines the implementation of and reactions to action learning through the Lean methodology in a unique, cross-cultural context. I review my time spent as a Lean coach; engaging with, training, and using action learning with employees in a garment manufacturing facility located in Bali, Indonesia. This research addresses…

Identifying habitats at risk: simple models can reveal complex ecosystem dynamics.

PubMed

Maxwell, Paul S; Pitt, Kylie A; Olds, Andrew D; Rissik, David; Connolly, Rod M

2015-03-01

The relationship between ecological impact and ecosystem structure is often strongly nonlinear, so that small increases in impact levels can cause a disproportionately large response in ecosystem structure. Nonlinear ecosystem responses can be difficult to predict because locally relevant data sets can be difficult or impossible to obtain. Bayesian networks (BN) are an emerging tool that can help managers to define ecosystem relationships using a range of data types from comprehensive quantitative data sets to expert opinion. We show how a simple BN can reveal nonlinear dynamics in seagrass ecosystems using ecological relationships sourced from the literature. We first developed a conceptual diagram by cataloguing the ecological responses of seagrasses to a range of drivers and impacts. We used the conceptual diagram to develop a BN populated with values sourced from published studies. We then applied the BN to show that the amount of initial seagrass biomass has a mitigating effect on the level of impact a meadow can withstand without loss, and that meadow recovery can often require disproportionately large improvements in impact levels. This mitigating effect resulted in the middle ranges of impact levels having a wide likelihood of seagrass presence, a situation known as bistability. Finally, we applied the model in a case study to identify the risk of loss and the likelihood of recovery for the conservation and management of seagrass meadows in Moreton Bay, Queensland, Australia. We used the model to predict the likelihood of bistability in 23 locations in the Bay. The model predicted bistability in seven locations, most of which have experienced seagrass loss at some stage in the past 25 years providing essential information for potential future restoration efforts. Our results demonstrate the capacity of simple, flexible modeling tools to facilitate collation and synthesis of disparate information. This approach can be adopted in the initial stages of conservation programs as a low-cost and relatively straightforward way to provide preliminary assessments of.nonlinear dynamics in ecosystems.

High Temperature and High Pressure Mixtures of Iron Oxides from the Impact Event at the Bee Bluff Crypto-Meteorite Impact Crater of South Texas

NASA Astrophysics Data System (ADS)

Graham, R. A.

2012-10-01

Disturbed geology within a several km diameter surface area of sedimentary Carrizo Sandstone near Uvalde, Texas, indicates the presence of a partially buried meteorite impact crater. Identification of its impact origin is supported by detailed studies but quartz grains recovered from distances of about100 km from the structure also show planar deformation features (PDFs). While PDFs are recognized as uniquely from impact processes, quantitative interpretation requires extension of Hugoniot materials models to more realistic grain-level, mixture models. Carrizo sandstone is a porous mixture of fine quartz and goethite. At impact pressures of tens of GPa, goethite separates into hematite and water vapor upon release of impact pressure. Samples from six different locations up to 50 km from the impact site preserve characteristic features resulting from mixtures of goethite, its water vapor, hematite and quartz. Spheroids resulting from local radial acceleration of mixed density, hot products are common at various sites. Local hydrodynamic instabilities cause similar effects.

Structural loads preliminary results

NASA Technical Reports Server (NTRS)

Alfaro-Bou, E.

1986-01-01

From a total of 351 instrumentation channels, 341 channels (97%) were in operation during the initial impact of the airplane. Both NASA seats, the energy absorbing seat and the standard seat, maintained their integrity during the impact. The floor accelerations at the seat locations were lower than the accelerations required for the energy absorbers to stroke; consequently, the energy absorbing seat did not stroke. The two seats remained firm in place during the crash and no seat attachment failures were observed. Due to the low accelerations experienced during the crash, both seats performed as standard seats. In the airplane structure, the accelerations were higher at both the point of impact in the left wing and at the forward end of the fuselage. The accelerations on the floor were higher toward the front than toward the rear and the floor accelerations on the left side were higher than on the right side at the front of the fuselage, but toward the rear they evened out.

Impact of Rate Design Alternatives on Residential Solar Customer Bills. Increased Fixed Charges, Minimum Bills and Demand-based Rates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bird, Lori; Davidson, Carolyn; McLaren, Joyce

With rapid growth in energy efficiency and distributed generation, electric utilities are anticipating stagnant or decreasing electricity sales, particularly in the residential sector. Utilities are increasingly considering alternative rates structures that are designed to recover fixed costs from residential solar photovoltaic (PV) customers with low net electricity consumption. Proposed structures have included fixed charge increases, minimum bills, and increasingly, demand rates - for net metered customers and all customers. This study examines the electricity bill implications of various residential rate alternatives for multiple locations within the United States. For the locations analyzed, the results suggest that residential PV customers offset,more » on average, between 60% and 99% of their annual load. However, roughly 65% of a typical customer's electricity demand is non-coincidental with PV generation, so the typical PV customer is generally highly reliant on the grid for pooling services.« less

Biofouling community composition across a range of environmental conditions and geographical locations suitable for floating marine renewable energy generation.

PubMed

Macleod, Adrian K; Stanley, Michele S; Day, John G; Cook, Elizabeth J

2016-01-01

Knowledge of biofouling typical of marine structures is essential for engineers to define appropriate loading criteria in addition to informing other stakeholders about the ecological implications of creating novel artificial environments. There is a lack of information regarding biofouling community composition (including weight and density characteristics) on floating structures associated with future marine renewable energy generation technologies. A network of navigation buoys were identified across a range of geographical areas, environmental conditions (tidal flow speed, temperature and salinity), and deployment durations suitable for future developments. Despite the perceived importance of environmental and temporal factors, geographical location explained the greatest proportion of the observed variation in community composition, emphasising the importance of considering geography when assessing the impact of biofouling on device functioning and associated ecology. The principal taxa associated with variation in biofouling community composition were mussels (Mytilus edulis), which were also important when determining loading criteria.

Selection of noisy measurement locations for error reduction in static parameter identification

NASA Astrophysics Data System (ADS)

Sanayei, Masoud; Onipede, Oladipo; Babu, Suresh R.

1992-09-01

An incomplete set of noisy static force and displacement measurements is used for parameter identification of structures at the element level. Measurement location and the level of accuracy in the measured data can drastically affect the accuracy of the identified parameters. A heuristic method is presented to select a limited number of degrees of freedom (DOF) to perform a successful parameter identification and to reduce the impact of measurement errors on the identified parameters. This pretest simulation uses an error sensitivity analysis to determine the effect of measurement errors on the parameter estimates. The selected DOF can be used for nondestructive testing and health monitoring of structures. Two numerical examples, one for a truss and one for a frame, are presented to demonstrate that using the measurements at the selected subset of DOF can limit the error in the parameter estimates.

Modeling Photosynthesis of Spartina alterniflora (smooth cordgrass) Impacted by the Deepwater Horizon Oil Spill Using Bayesian Inference

NASA Astrophysics Data System (ADS)

Wu, W.; Biber, P. D.; Peterson, M. S.; Gong, C.

2012-12-01

We studied the impact of the Deepwater Horizon oil spill on photosynthesis of coastal saltmarsh plants in Mississippi from July 2010 to November 2011 using field measurements and a hierarchical Bayesian (HB) model. We sampled three locations in Davis Bayou, Mississippi (30.375°N, 88.790°W) representative of a range of oil spill impacts. Measured photosynthesis was negative (respiration only) at the heavily oiled location in July 2010 only, and rates started to increase by August 2010. Photosynthesis at the medium oiled location was lower than at the control location in July 2010 and it continued to decrease in September 2010. During the winter months in 2010-2011, the contrast between the control and the two impacted locations was not as obvious as in the growing season of 2010. Photosynthesis increased through spring 2011 at the three locations and decreased starting with October at the control location and a month earlier (September) at the impacted locations. Using the field data, we developed an HB model. The model simulations agreed well with the measured photosynthesis, and they captured most of the variability of the measured data. Based on the posteriors of the parameters, air temperature and photosynthetic active radiation (PAR) positively influenced photosynthesis whereas the leaf stress level negatively affected photosynthesis. The photosynthesis rates at the heavily impacted location had recovered to the status of the control location about 140 days after the initial impact, while the impact at the medium location was never severe enough to make photosynthesis significantly lower than that at the control location over the study period. The uncertainty in modeling photosynthesis rates mainly came from the individual and micro-site scales, less from the leaf scale. Medians with 95% confidence intervals for the measured photosynthesis rate (μmol C m-2 s-1 - y axis) at the locations of A) Control, B) Medium impact, and C) Heavy impact in each month from July 2010 to November 2011. At the x-axis representing the photosynthetic active radiation intensity, 1 = around 400 μmol C m-2 s-1, 2 = around 800 μmol C m-2 s-1, 3 = around 1200 μmol C m-2 s-1, 4 = around 1600 μmol C m-2 s-1, and 5 = around 2000 μmol C m-2 s-1.

The Acraman impact and its widespread ejecta, South Australia

NASA Technical Reports Server (NTRS)

Gostin, V. A.; Keays, R. R.; Wallace, M. W.

1992-01-01

Discovery of a widespread horizon of shock-deformed volcaniclastic ejecta preserved in Late Proterozoic (approx. 600 Ma) shales in South Australia and its probable link to the Acraman impact structure in the Middle Proterozoic Gawler Range. Volcanics provide a rare opportunity to study the effects of a major terrestrial impact, including the sedimentology and distribution of an ejecta blanket and its precious-metal signature. The ejecta horizon occurs in the Bunyeroo Formation at many localities within the Adelaide Geosyncline, including the Wearing Hills, which are approx. 350 km northeast of the Acraman impact site. Following a search at the same stratigraphic level in other basins in South Australia, the ejecta has been located within the Lower Rodda beds of the Officer Basin, extending the limits of the ejecta to approx. 470 km northwest of the Acraman impact structure. The ejecta is therefore widely dispersed, and provides an important chronostratigraphic marker enabling precise correlation of Late Proterozoic sequences in southern Australia. In summary, the Bunyeroo ejecta is unique as the only known example of a widely dispersed, coarse-grained ejecta blanket that is, moreover, strongly linked to a known major impact structure. The marked Ir-PGE anomalies in the ejecta horizon provide support for the hypothesis that meteorite impact events can produce Ir anomalies interrestrial sediments. The findings also indicate that Ir can be mobilized and concentrated in sediments by low-temperature diagenetic processes. The identification of ejecta horizons in sedimentary rocks therefore should be based on the coincidence of shock-metamorphic features in the detritus and clear Ir anomalies.

NCI designated cancer center funding not influenced by organizational structure.

PubMed

Wolfe, Margaret E; Yagoda, Daniel; Thurman, Paul W; Luna, Jorge M; Figg, William Douglas

2009-05-01

National Cancer Institutes (NCI) designated cancer centers use one of three organizational structures. The hypothesis of this study is that there are differences in the amount of annual NCI funding per faculty member based on a cancer center's organizational structure. The study also considers the impact of secondary factors (i.e., the existence of a clinical program, the region and the size of the city in which the cancer center is located) on funding and the number of Howard Hughes Medical Institute (HHMI) investigators at each cancer center. Of the 63 cancer centers, 44 use a matrix structure, 16 have a freestanding structure, and three have a Department of Oncology structure. Kruskal-Wallis tests reveal no statistically significant differences in the amount of funding per faculty member or the number of HHMI investigators between centers with a matrix, freestanding or Department of Oncology structure. Online research and telephone interviews with each cancer center were used to gather information, including: organizational structure, the presence of a clinical program, the number of faculty members, and the number of Howard Hughes Medical Institute investigators. Statistical tests were used to assess the impact which organizational structure has on the amount of funding per faculty member and number of HHMI investigators. While the results seem to suggest that the organizational structure of a given cancer center does not impact the amount of NCI funding or number of HHMI investigators which it attracts, the existence of this relationship is likely masked by the small sample size in this study. Further studies may be appropriate to examine the effect organizational structure has on other measurements which are relevant to cancer centers, such as quality and quantity of research produced.

Large impacts in the Baltic shield with special attention to the Uppland structure

NASA Technical Reports Server (NTRS)

Henkel, H.; Lilljequist, R.

1992-01-01

Within the Baltic Shield several very large structures have been identified and are suspected to be of meteorite impact origin. Some of these deeply eroded circular features are presented with special attention to the Uppland structure, where several indications point toward an impact origin in the mid-Proterozoic. The structures exceed 100 km in diameter and the topographic expression is inferior or absent. An arcuate arrangement of lithologies occurs around the margin of the structures and the central regions show conform magnetic and positive gravity anomalies. The Uppland structure is approximately 320 km in diameter as expressed by morphological, geological, and geophysical concentric patterns. The central part is topographically remarkably flat and is characterized by an unusual irregular fracture pattern. A subcircular central tonalite with density of 2.81 Mg(sup -3) gives a positive gravity anomaly of 35 mgal and the gravimetric profile is very similar to that of Manicouagan and Vredefort. The tonalite constitutes a huge antiform, 80 km in diameter, probably representing a 12-km structural uplift of infracrustal rocks. The flancs of the tonalite are characterized by recrystallized pseudotachylitic breccia dykes and breccia zones. Around the central parts amphibolite-grade metamorphic rocks appear as large fragments within a fine-grained granite interpreted as a thermally annealed melt rock. Several occurrences of breccia dykes and breccia-bearing melts have been identified about 100 km from the gravimetric center of the structure. Impact-related ore deposits are located around the margin of the structure and are interpreted as preexisting downfaulted iron formations, and deposits formed from remobilization of these preimpact occurrences. The so-called ball ores are interpreted to have formed by fluid injection similar to the formation of breccia dykes. The extensive hydrothermal alteration along the outer margin of the structure have created extreme soda and K-enriched rocks ('leptites') from preexisting gneiss granites and supracrustal sedimentary gneisses.

The Cretaceous-Tertiary (K/T) impact: One or more source craters?

NASA Technical Reports Server (NTRS)

Koeberl, Christian

1992-01-01

The Cretaceous-Tertiary (K/T) boundary is marked by signs of a worldwide catastrophe, marking the demise of more than 50 percent of all living species. Ever since Alvarez et al. found an enrichment of IR and other siderophile elements in rocks marking the K/T boundary and interpreted it as the mark of a giant asteroid (or comet) impact, scientists have tried to understand the complexities of the K/T boundary event. The impact theory received a critical boost by the discovery of shocked minerals that have so far been found only in association with impact craters. One of the problems of the K/T impact theory was, and still is, the lack of an adequate large crater that is close to the maximum abundance of shocked grains in K/T boundary sections, which was found to occur in sections in Northern America. The recent discovery of impact glasses from a K/T section in Haiti has been crucial in establishing a connection with documented impact processes. The location of the impact-glass findings and the continental nature of detritus found in all K/T sections supports at least one impact site near the North American continent. The Manson Impact Structure is the largest recognized in the United States, 35 km in diameter, and has a radiometric age indistinguishable from that of the Cretaceous-Tertiary (K/T) boundary. Although the Manson structure may be too small, it may be considered at least one element of the events that led to the catastrophic loss of life and extinction of many species at that time. A second candidate for the K/T boundary crater is the Chicxulub structure, which was first suggested to be an impact crater more than a decade ago. Only recently, geophysical studies and petrological (as well as limited chemical) analyses have indicated that this buried structure may in fact be of impact origin. At present we can conclude that the Manson crater is the only confirmed crater of K/T age, but Chicxulub is becoming a strong contender; however, detailed geochemical, geochronological, and isotopic data are necessary to provide definitive evidence.

The Cretaceous-Tertiary (K/T) impact: One or more source craters?

NASA Astrophysics Data System (ADS)

Koeberl, Christian

The Cretaceous-Tertiary (K/T) boundary is marked by signs of a worldwide catastrophe, marking the demise of more than 50 percent of all living species. Ever since Alvarez et al. found an enrichment of IR and other siderophile elements in rocks marking the K/T boundary and interpreted it as the mark of a giant asteroid (or comet) impact, scientists have tried to understand the complexities of the K/T boundary event. The impact theory received a critical boost by the discovery of shocked minerals that have so far been found only in association with impact craters. One of the problems of the K/T impact theory was, and still is, the lack of an adequate large crater that is close to the maximum abundance of shocked grains in K/T boundary sections, which was found to occur in sections in Northern America. The recent discovery of impact glasses from a K/T section in Haiti has been crucial in establishing a connection with documented impact processes. The location of the impact-glass findings and the continental nature of detritus found in all K/T sections supports at least one impact site near the North American continent. The Manson Impact Structure is the largest recognized in the United States, 35 km in diameter, and has a radiometric age indistinguishable from that of the Cretaceous-Tertiary (K/T) boundary. Although the Manson structure may be too small, it may be considered at least one element of the events that led to the catastrophic loss of life and extinction of many species at that time. A second candidate for the K/T boundary crater is the Chicxulub structure, which was first suggested to be an impact crater more than a decade ago. Only recently, geophysical studies and petrological (as well as limited chemical) analyses have indicated that this buried structure may in fact be of impact origin. At present we can conclude that the Manson crater is the only confirmed crater of K/T age, but Chicxulub is becoming a strong contender; however, detailed geochemical, geochronological, and isotopic data are necessary to provide definitive evidence.

Extracting full-field dynamic strain on a wind turbine rotor subjected to arbitrary excitations using 3D point tracking and a modal expansion technique

NASA Astrophysics Data System (ADS)

Baqersad, Javad; Niezrecki, Christopher; Avitabile, Peter

2015-09-01

Health monitoring of rotating structures such as wind turbines and helicopter rotors is generally performed using conventional sensors that provide a limited set of data at discrete locations near or on the hub. These sensors usually provide no data on the blades or inside them where failures might occur. Within this paper, an approach was used to extract the full-field dynamic strain on a wind turbine assembly subject to arbitrary loading conditions. A three-bladed wind turbine having 2.3-m long blades was placed in a semi-built-in boundary condition using a hub, a machining chuck, and a steel block. For three different test cases, the turbine was excited using (1) pluck testing, (2) random impacts on blades with three impact hammers, and (3) random excitation by a mechanical shaker. The response of the structure to the excitations was measured using three-dimensional point tracking. A pair of high-speed cameras was used to measure displacement of optical targets on the structure when the blades were vibrating. The measured displacements at discrete locations were expanded and applied to the finite element model of the structure to extract the full-field dynamic strain. The results of the paper show an excellent correlation between the strain predicted using the proposed approach and the strain measured with strain-gages for each of the three loading conditions. The approach used in this paper to predict the strain showed higher accuracy than the digital image correlation technique. The new expansion approach is able to extract dynamic strain all over the entire structure, even inside the structure beyond the line of sight of the measurement system. Because the method is based on a non-contacting measurement approach, it can be readily applied to a variety of structures having different boundary and operating conditions, including rotating blades.

Health impacts of floods.

PubMed

Du, Weiwei; FitzGerald, Gerard Joseph; Clark, Michele; Hou, Xiang-Yu

2010-01-01

Floods are the most common hazard to cause disasters and have led to extensive morbidity and mortality throughout the world. The impact of floods on the human community is related directly to the location and topography of the area, as well as human demographics and characteristics of the built environment. The aim of this study is to identify the health impacts of disasters and the underlying causes of health impacts associated with floods. A conceptual framework is developed that may assist with the development of a rational and comprehensive approach to prevention, mitigation, and management. This study involved an extensive literature review that located >500 references, which were analyzed to identify common themes, findings, and expert views. The findings then were distilled into common themes. The health impacts of floods are wide ranging, and depend on a number of factors. However, the health impacts of a particular flood are specific to the particular context. The immediate health impacts of floods include drowning, injuries, hypothermia, and animal bites. Health risks also are associated with the evacuation of patients, loss of health workers, and loss of health infrastructure including essential drugs and supplies. In the medium-term, infected wounds, complications of injury, poisoning, poor mental health, communicable diseases, and starvation are indirect effects of flooding. In the long-term, chronic disease, disability, poor mental health, and poverty-related diseases including malnutrition are the potential legacy. This article proposes a structured approach to the classification of the health impacts of floods and a conceptual framework that demonstrates the relationships between floods and the direct and indirect health consequences.

A Multi-Level Decision Fusion Strategy for Condition Based Maintenance of Composite Structures

PubMed Central

Sharif Khodaei, Zahra; Aliabadi, M.H.

2016-01-01

In this work, a multi-level decision fusion strategy is proposed which weighs the Value of Information (VoI) against the intended functions of a Structural Health Monitoring (SHM) system. This paper presents a multi-level approach for three different maintenance strategies in which the performance of the SHM systems is evaluated against its intended functions. Level 1 diagnosis results in damage existence with minimum sensors covering a large area by finding the maximum energy difference for the guided waves propagating in pristine structure and the post-impact state; Level 2 diagnosis provides damage detection and approximate localization using an approach based on Electro-Mechanical Impedance (EMI) measures, while Level 3 characterizes damage (exact location and size) in addition to its detection by utilising a Weighted Energy Arrival Method (WEAM). The proposed multi-level strategy is verified and validated experimentally by detection of Barely Visible Impact Damage (BVID) on a curved composite fuselage panel. PMID:28773910

High-resolution seismic-reflection images across the ICDP-USGS Eyreville deep drilling site, Chesapeake Bay impact structure

USGS Publications Warehouse

Powars, David S.; Catchings, Rufus D.; Goldman, Mark R.; Gohn, Gregory S.; Horton, J. Wright; Edwards, Lucy E.; Rymer, Michael J.; Gandhok, Gini

2009-01-01

The U.S. Geological Survey (USGS) acquired two 1.4-km-long, high-resolution (~5 m vertical resolution) seismic-reflection lines in 2006 that cross near the International Continental Scientific Drilling Program (ICDP)-USGS Eyreville deep drilling site located above the late Eocene Chesapeake Bay impact structure in Virginia, USA. Five-meter spacing of seismic sources and geophones produced high-resolution images of the subsurface adjacent to the 1766-m-depth Eyreville core holes. Analysis of these lines, in the context of the core hole stratigraphy, shows that moderate-amplitude, discontinuous, dipping reflections below ~527 m correlate with a variety of Chesapeake Bay impact structure sediment and rock breccias recovered in the cores. High-amplitude, continuous, subhorizontal reflections above ~527 m depth correlate with the uppermost part of the Chesapeake Bay impact structure crater-fill sediments and postimpact Eocene to Pleistocene sediments. Reflections with ~20-30 m of relief in the uppermost part of the crater-fill and lowermost part of the postimpact section suggest differential compaction of the crater-fill materials during early postimpact time. The top of the crater-fill section also shows ~20 m of relief that appears to represent an original synimpact surface. Truncation surfaces, locally dipping reflections, and depth variations in reflection amplitudes generally correlate with the lithostrati-graphic and sequence-stratigraphic units and contacts in the core. Seismic images show apparent postimpact paleochannels that include the first possible Miocene paleochannels in the Mid-Atlantic Coastal Plain. Broad downwarping in the postim-pact section unrelated to structures in the crater fill indicates postimpact sediment compaction.

Localised Effects of a Mega-Disturbance: Spatiotemporal Responses of Intertidal Sandy Shore Communities to the 2010 Chilean Earthquake.

PubMed

Sepúlveda, Roger D; Valdivia, Nelson

2016-01-01

Determining the effects of unpredictable disturbances on dynamic ecological systems is challenged by the paucity of appropriate temporal and spatial coverage of data. On 27 February 2010, an 8.8 Mw mega-earthquake and tsunami struck central Chile and caused coastal land-level changes, massive damage to coastal infrastructure, and widespread mortality of coastal organisms. Wave-exposed sandy beaches showed significant changes of species abundances from before to after the earthquake, but the highly dynamic biotic and abiotic conditions of these habitats make difficult to draw clear-cut conclusions from these patterns. Here, we analysed a beyond-BACI (Before-After Control-Impact) sampling design to test whether the effects of the Maule earthquake on sandy-shore species diversity, abundance, and structure were heterogeneous along the shore. Invertebrate species abundances were quantified before (i.e. February 2010) and after (i.e. March 2010, September 2010, and March 2011) the earthquake at three sandy shores randomly located within the earthquake rupture area and three sites within a "control" area located >400 km southward from epicentre. Immediately after the earthquake took place, the three sites located in the rupture area showed anomalous beach-profile uplifts that did not comply with the erosion (i.e. "negative" uplifts) that regularly occurs during late summer in the region. Species richness, abundance, and community structure significantly varied from before to after the strike, but these patterns of change varied among sites within both areas. Only the site with the strongest and persistent beach-profile uplift within the rupture area showed significant concomitant changes in species richness and community structure; after 13 months, this community showed a similar multivariate structure to the before-disturbance state. This site, in particular, was located in the section of the rupture area that received most of the impact of the after-earthquake tsunami. Therefore, our results suggest that the effects of the Maule mega-earthquake on the ecological communities were spatially heterogeneous and highly localised. We suggest that high mobility and other species' adaptations to the dynamic environmental conditions of sandy beaches might explain the comparatively high resilience of these assemblages. With this work we hope to motivate further experimental research on the role of individual- and population-level properties in the response of sandy-beach communities to interacting sources of disturbances.

Localised Effects of a Mega-Disturbance: Spatiotemporal Responses of Intertidal Sandy Shore Communities to the 2010 Chilean Earthquake

PubMed Central

Sepúlveda, Roger D.; Valdivia, Nelson

2016-01-01

Determining the effects of unpredictable disturbances on dynamic ecological systems is challenged by the paucity of appropriate temporal and spatial coverage of data. On 27 February 2010, an 8.8 Mw mega-earthquake and tsunami struck central Chile and caused coastal land-level changes, massive damage to coastal infrastructure, and widespread mortality of coastal organisms. Wave-exposed sandy beaches showed significant changes of species abundances from before to after the earthquake, but the highly dynamic biotic and abiotic conditions of these habitats make difficult to draw clear-cut conclusions from these patterns. Here, we analysed a beyond-BACI (Before-After Control-Impact) sampling design to test whether the effects of the Maule earthquake on sandy-shore species diversity, abundance, and structure were heterogeneous along the shore. Invertebrate species abundances were quantified before (i.e. February 2010) and after (i.e. March 2010, September 2010, and March 2011) the earthquake at three sandy shores randomly located within the earthquake rupture area and three sites within a “control” area located >400 km southward from epicentre. Immediately after the earthquake took place, the three sites located in the rupture area showed anomalous beach-profile uplifts that did not comply with the erosion (i.e. “negative” uplifts) that regularly occurs during late summer in the region. Species richness, abundance, and community structure significantly varied from before to after the strike, but these patterns of change varied among sites within both areas. Only the site with the strongest and persistent beach-profile uplift within the rupture area showed significant concomitant changes in species richness and community structure; after 13 months, this community showed a similar multivariate structure to the before-disturbance state. This site, in particular, was located in the section of the rupture area that received most of the impact of the after-earthquake tsunami. Therefore, our results suggest that the effects of the Maule mega-earthquake on the ecological communities were spatially heterogeneous and highly localised. We suggest that high mobility and other species’ adaptations to the dynamic environmental conditions of sandy beaches might explain the comparatively high resilience of these assemblages. With this work we hope to motivate further experimental research on the role of individual- and population-level properties in the response of sandy-beach communities to interacting sources of disturbances. PMID:27383744

Recent research on the Chesapeake Bay impact structure, USA - Impact debris and reworked ejecta

USGS Publications Warehouse

Horton, J. Wright; Aleinikoff, John N.; Kunk, Michael J.; Gohn, Gregory S.; Edwards, Lucy E.; Self-Trail, Jean M.; Powars, David S.; Izett, Glen A.

2005-01-01

Four new coreholes in the western annular trough of the buried, late Eocene Chesapeake Bay impact structure provide samples of shocked minerals, cataclastic rocks, possible impact melt, mixed sediments, and damaged microfossils. Parautochthonous Cretaceous sediments show an upward increase in collapse, sand fluidization, and mixed sediment injections. These impact-modified sediments are scoured and covered by the upper Eocene Exmore beds, which consist of highly mixed Cretaceous to Eocene sediment clasts and minor crystalline-rock clasts in a muddy quartz-glauconite sand matrix. The Exmore beds are interpreted as seawater-resurge debris flows. Shocked quartz is found as sparse grains and in rock fragments at all four sites in the Exmore, where these fallback remnants are mixed into the resurge deposit. Crystalline-rock clasts that exhibit shocked quartz or cataclastic fabrics include felsites, granitoids, and other plutonic rocks. Felsite from a monomict cataclasite boulder has a sensitive high-resolution ion microprobe U-Pb zircon age of 613 ± 4 Ma. Leucogranite from a polymict cataclasite boulder has a similar Neoproterozoic age based on muscovite 40Ar/39Ar data. Potassium-feldspar 40Ar/39Ar ages from this leucogranite show cooling through closure (∼150 °C) at ca. 261 Ma without discernible impact heating. Spherulitic felsite is under investigation as a possible impact melt. Types of crystalline clasts, and exotic sediment clasts and grains, in the Exmore vary according to location, which suggests different provenances across the structure. Fractured calcareous nannofossils and fused, bubbled, and curled dinoflagellate cysts coexist with shocked quartz in the Exmore, and this damage may record conditions of heat, pressure, and abrasion due to impact in a shallow-marine environment.

Using Unmanned Aerial Vehicles (UAVs) to Modeling Tornado Impacts

NASA Astrophysics Data System (ADS)

Wagner, M.; Doe, R. K.

2017-12-01

Using Unmanned Aerial Vehicles (UAVs) to assess storm damage is a useful research tool. Benefits include their ability to access remote or impassable areas post-storm, identify unknown damages and assist with more detailed site investigations and rescue efforts. Technological advancement of UAVs mean that they can capture high resolution images often at an affordable price. These images can be used to create 3D environments to better interpret and delineate damages from large areas that would have been difficult in ground surveys. This research presents the results of a rapid response site investigation of the 29 April 2017 Canton, Texas, USA, tornado using low cost UAVs. This was a multiple, high impact tornado event measuring EF4 at maximum. Rural farmland was chosen as a challenging location to test both equipment and methodology. Such locations provide multiple impacts at a variety of scales including structural and vegetation damage and even animal fatalities. The 3D impact models allow for a more comprehensive study prior to clean-up. The results show previously unseen damages and better quantify damage impacts at the local level. 3D digital track swaths were created allowing for a more accurate track width determination. These results demonstrate how effective the use of low cost UAVs can be for rapid response storm damage assessments, the high quality of data they can achieve, and how they can help us better visualize tornado site investigations.

Health Monitoring of Composite Material Structures using a Vibrometry Technique

NASA Technical Reports Server (NTRS)

Schulz, Mark J.

1997-01-01

Large composite material structures such as aircraft and Reusable Launch Vehicles (RLVS) operate in severe environments comprised of vehicle dynamic loads, aerodynamic loads, engine vibration, foreign object impact, lightning strikes, corrosion, and moisture absorption. These structures are susceptible to damage such as delamination, fiber breaking/pullout, matrix cracking, and hygrothermal strain. To ensure human safety and load-bearing integrity, these structures must be inspected to detect and locate often invisible damage and faults before becoming catastrophic. Moreover, nearly all future structures will need some type of in-service inspection technique to increase their useful life and reduce maintenance and overall costs. Possible techniques for monitoring the health and indicating damage on composite structures include: c-scan, thermography, acoustic emissions using piezoceramic actuators or fiber-optic wires with gratings, laser ultrasound, shearography, holography, x-ray, and others. These techniques have limitations in detecting damage that is beneath the surface of the structure, far away from a sensor location, or during operation of the vehicle. The objective of this project is to develop a more global method for damage detection that is based on structural dynamics principles, and can inspect for damage when the structure is subjected to vibratory loads to expose faults that may not be evident by static inspection. A Transmittance Function Monitoring (TFM) method is being developed in this project for ground-based inspection and operational health monitoring of large composite structures as a RLV. A comparison of the features of existing health monitoring approaches and the proposed TFM method is given.

The Role of the Dynamic Plasmapause on Outer Radiation Belt Electron Flux Enhancement and Three-Belt Structure Formation

NASA Astrophysics Data System (ADS)

Bruff, M.; Jaynes, A. N.; Zhao, H.; Malaspina, D.

2017-12-01

The plasmasphere is a highly dynamic toroidal region of cold, dense plasma around Earth. Plasma waves exist both inside and outside this region and can contribute to the loss and acceleration of high energy outer radiation belt electrons. Early observational studies found an apparent correlation on long time scales between the observed inner edge of the outer radiation belt and the simulated innermost plasmapause location. More recent work using high resolution Van Allen Probe satellite data has found a more complex relationship. The aim of this project was to provide a systematic study of the location and dynamics of the plasmapause compared to the MeV electrons in the outer radiation belt. We used spin-averaged electron flux data from the Relativistic Electron Proton Telescope (REPT) and density data derived from the EFW instrument on the Van Allen Probe satellites. We analyzed these data to determine the standoff distance of the location of peak electron flux of the outer belt MeV electrons from the plasmapause. We found that the location of peak flux was consistently outside but within ΔL=2.5 from the innermost location of the plasmapause at enhancement times, with an average standoff distance ΔL=1.0 +/- 0.5. This is consistent with the current model of chorus enhancement and previous observations of chorus activity. Finally, we identified "three-belt" structure events where a second outer belt formed and found a repeated pattern of plasmapause dynamics associated with specific changes in electron flux required to generate and sustain these structures. This study is significant to improving our understanding of how the plasmasphere under differing conditions can both shield Earth from or worsen the impacts of geomagnetic activity.

Direct etch method for microfludic channel and nanoheight post-fabrication by picoliter droplets

NASA Astrophysics Data System (ADS)

Demirci, Utkan; Toner, Mehmet

2006-01-01

Photolithography is an expensive and significant step in microfabrication. Approaches that could change lithography would create an impact on semiconductor industry and microelectromechanical systems technologies. We demonstrate a direct etching method by ejecting etchant droplets at desired locations by using microdroplet ejector arrays. This method could be used for easy fabrication of poly(dimethylsiloxane) microfluidic channels and nanometer height postlike structures in microfluidic channels.

Coordination Without Borders Assigning US Military Officers to NGO World Headquarters: Rhetoric and Reality

DTIC Science & Technology

2009-05-21

Freedom). The DoD has executed a ―go it alone‖ policy, i.e. US military forces have had to make the peace, resolve the issues and operationally manage ...rank or grade structures, assignment locations, career impacts, tour lengths, rating chains and position funding are issues the US military must...contrasts NGO operations when confronted with military commanders who manage ―battle space.‖ 14

Hurricane recovery at Cabezas de San Juan, Puerto Rico, and research opportunities at Conservation Trust Reserves

Treesearch

Peter L. Weaver; Elizabeth Padilla Rodriguez

2009-01-01

The Cabezas de San Juan Natural Reserve (El Faro), an exposed peninsular area located in the Subtropical dry forest of northeastern Puerto Rico, was impacted by hurricanes Hugo (1989) and Georges (1998). From 1998 to 2008, a 0.10 ha plot was used to assess forest structure, species composition, and stem growth. During post-hurricane recovery, stem density, tree height...

Design and analysis of compound flexible skin based on deformable honeycomb

NASA Astrophysics Data System (ADS)

Zou, Tingting; Zhou, Li

2017-04-01

In this study, we focused at the development and verification of a robust framework for surface crack detection in steel pipes using measured vibration responses; with the presence of multiple progressive damage occurring in different locations within the structure. Feature selection, dimensionality reduction, and multi-class support vector machine were established for this purpose. Nine damage cases, at different locations, orientations and length, were introduced into the pipe structure. The pipe was impacted 300 times using an impact hammer, after each damage case, the vibration data were collected using 3 PZT wafers which were installed on the outer surface of the pipe. At first, damage sensitive features were extracted using the frequency response function approach followed by recursive feature elimination for dimensionality reduction. Then, a multi-class support vector machine learning algorithm was employed to train the data and generate a statistical model. Once the model is established, decision values and distances from the hyper-plane were generated for the new collected data using the trained model. This process was repeated on the data collected from each sensor. Overall, using a single sensor for training and testing led to a very high accuracy reaching 98% in the assessment of the 9 damage cases used in this study.

Detection of surface cracking in steel pipes based on vibration data using a multi-class support vector machine classifier

NASA Astrophysics Data System (ADS)

Mustapha, S.; Braytee, A.; Ye, L.

2017-04-01

In this study, we focused at the development and verification of a robust framework for surface crack detection in steel pipes using measured vibration responses; with the presence of multiple progressive damage occurring in different locations within the structure. Feature selection, dimensionality reduction, and multi-class support vector machine were established for this purpose. Nine damage cases, at different locations, orientations and length, were introduced into the pipe structure. The pipe was impacted 300 times using an impact hammer, after each damage case, the vibration data were collected using 3 PZT wafers which were installed on the outer surface of the pipe. At first, damage sensitive features were extracted using the frequency response function approach followed by recursive feature elimination for dimensionality reduction. Then, a multi-class support vector machine learning algorithm was employed to train the data and generate a statistical model. Once the model is established, decision values and distances from the hyper-plane were generated for the new collected data using the trained model. This process was repeated on the data collected from each sensor. Overall, using a single sensor for training and testing led to a very high accuracy reaching 98% in the assessment of the 9 damage cases used in this study.

Homing of invasive Burmese pythons in South Florida: evidence for map and compass senses in snakes

PubMed Central

Pittman, Shannon E.; Hart, Kristen M.; Cherkiss, Michael S.; Snow, Ray W.; Fujisaki, Ikuko; Smith, Brian J.; Mazzotti, Frank J.; Dorcas, Michael E.

2014-01-01

Navigational ability is a critical component of an animal's spatial ecology and may influence the invasive potential of species. Burmese pythons (Python molurus bivittatus) are apex predators invasive to South Florida. We tracked the movements of 12 adult Burmese pythons in Everglades National Park, six of which were translocated 21–36 km from their capture locations. Translocated snakes oriented movement homeward relative to the capture location, and five of six snakes returned to within 5 km of the original capture location. Translocated snakes moved straighter and faster than control snakes and displayed movement path structure indicative of oriented movement. This study provides evidence that Burmese pythons have navigational map and compass senses and has implications for predictions of spatial spread and impacts as well as our understanding of reptile cognitive abilities. PMID:24647727

Homing of invasive Burmese pythons in South Florida: evidence for map and compass senses in snakes

USGS Publications Warehouse

Pittman, Shannon E.; Hart, Kristen M.; Cherkiss, Michael S.; Snow, Ray W.; Fujisaki, Ikuko; Mazzotti, Frank J.; Dorcas, Michael E.

2014-01-01

Navigational ability is a critical component of an animal's spatial ecology and may influence the invasive potential of species. Burmese pythons (Python molurus bivittatus) are apex predators invasive to South Florida. We tracked the movements of 12 adult Burmese pythons in Everglades National Park, six of which were translocated 21–36 km from their capture locations. Translocated snakes oriented movement homeward relative to the capture location, and five of six snakes returned to within 5 km of the original capture location. Translocated snakes moved straighter and faster than control snakes and displayed movement path structure indicative of oriented movement. This study provides evidence that Burmese pythons have navigational map and compass senses and has implications for predictions of spatial spread and impacts as well as our understanding of reptile cognitive abilities.

Earth Observations taken by the Expedition 17 Crew

NASA Image and Video Library

2008-10-21

ISS017-E-020538 (21 Oct. 2008) --- Arkenu Craters 1 and 2 in Libya are featured in this image photographed by an Expedition 17 crewmember on the International Space Station. Geologists often study features on Earth, such as impact craters, to gain insight into processes that occur on other planets. On Earth, more than 150 impact craters have been identified on the continents, but only a few of these are classified as double impact craters. One such example, the Arkenu Craters in northern Africa, is shown in this image. Arkenu 1 and 2 are double impact structures located in eastern Libya (22.04 degrees north latitude and 23.45 degrees east longitude) in the Sahara desert, with diameters of approximately 6.8 kilometers and 10.3 kilometers, respectively. The craters are unusual in that they both exhibit concentric annular ridge structures (gray circles in the image indicate the position of the outermost visible ridges). In many terrestrial complex craters these features are highly eroded and no longer visible. While the circular structure of these features had been noted, the impact origin hypothesis was strengthened in December 2003 when a field team observed shatter cones -- conical-shaped features in rocks created by the high shock pressures generated during impact. Large outcrops of impact breccias -- a jumble of rock fragments generated at the impact site that are now cemented together into an identifiable rock layer -- were also observed by the field team. Two impactors, each approximately 500 meters in diameter, are thought to have created the craters. According to scientists, the age of the impact event has been dated as occurring less than 140 million years ago. While the presence of shatter cones and impact breccias is generally considered to be strong evidence for meteor impact, some scientists now question the interpretation of these features observed at the Arkenu structures and suggest that they were caused by erosive and volcanic processes. At present, both craters are being crossed by linear dunes extending northeast-southwest -- the superposition of the dunes across the annular ridges indicates that they are much younger than the craters.

Possible Impact Origin for the Late Ordovician Bear Swamp Structure in the Finger Lakes Region of New York

NASA Astrophysics Data System (ADS)

Leiphart, D.

2010-12-01

Impact structures, or astroblemes, are one of rarest formations in the geologic record. Presently there are 176 confirmed impact structures on the planet with roughly two-thirds of them evident at the surface. A potential impact structure has been discovered in a 3D seismic survey in the Finger Lakes Region of upstate New York (Figure 1 - N42o43.187’; W76o16.637’). The Bear Swamp crater is uppermost Ordovician (~444 Ma) in age and is situated within the fluvial-deltaic to shallow marine Queenston Formation. This nearly circular structure measures 3.5 km (2.2 mi) in diameter and is completely buried in the subsurface at a depth of approximately 1,220 m (4,000 ft). Seismic data show a central uplift within the crater that rises about 160 m (525 ft) above the base. Around the central uplift is an annular basin that is more than 300 m (~1,000 ft) thick and is characterized by synformal seismic reflectors (Figure 1). This three-dimensional morphology resembles other complex craters of confirmed impact origin. Two exploration wells were drilled into the crater and image logs were run. The first well tested the central rebound which consists of steeply dipping beds and heavily brecciated zones. The second well was drilled in the annular basin which contains alternating sequences of chaotic zones and shallow dipping beds. Based on analogous impact structures, this crater fill is here interpreted as resurge breccias and turbidites which were the result of intense wave action in the moments after impact. Above these impact-related deposits lies a zone of very thin (~2cm) laminae which resemble varved sediments in lacustrine environments. A bioturbated zone overlies these thin laminae, which is in turn capped by the End Ordovician unconformity. Observations of both seismic and well data are consistent with a shallow marine to transition zone impact origin for the Bear Swamp crater. Figure 1: Location map showing the area of the ~180 km2 (70 mi2) 3D seismic survey and the proposed Bear Swamp Astrobleme. The map in the lower left is a time slice through a coherency volume at 650 milliseconds. The inset at the lower right is a cutout of the 3D volume with the Queenston top and base crater horizon extrapolated out.

Effects of Large-Scale Releases on the Genetic Structure of Red Sea Bream (Pagrus major, Temminck et Schlegel) Populations in Japan.

PubMed

Blanco Gonzalez, Enrique; Aritaki, Masato; Knutsen, Halvor; Taniguchi, Nobuhiko

2015-01-01

Large-scale hatchery releases are carried out for many marine fish species worldwide; nevertheless, the long-term effects of this practice on the genetic structure of natural populations remains unclear. The lack of knowledge is especially evident when independent stock enhancement programs are conducted simultaneously on the same species at different geographical locations, as occurs with red sea bream (Pagrus major, Temminck et Schlegel) in Japan. In this study, we examined the putative effects of intensive offspring releases on the genetic structure of red sea bream populations along the Japanese archipelago by genotyping 848 fish at fifteen microsatellite loci. Our results suggests weak but consistent patterns of genetic divergence (F(ST) = 0.002, p < 0.001). Red sea bream in Japan appeared spatially structured with several patches of distinct allelic composition, which corresponded to areas receiving an important influx of fish of hatchery origin, either released intentionally or from unintentional escapees from aquaculture operations. In addition to impacts upon local populations inhabiting semi-enclosed embayments, large-scale releases (either intentionally or from unintentional escapes) appeared also to have perturbed genetic structure in open areas. Hence, results of the present study suggest that independent large-scale marine stock enhancement programs conducted simultaneously on one species at different geographical locations may compromise native genetic structure and lead to patchy patterns in population genetic structure.

Articulation handicap index: an instrument for quantifying psychosocial consequences of impaired articulation.

PubMed

Keilmann, Annerose; Konerding, Uwe; Oberherr, Constantin; Nawka, Tadeus

2016-12-01

Structural, neurological and muscular diseases can lead to impairments of articulation. These impairments can severely impact social life. To judge health status comprehensively, this impact must be adequately quantified. For this purpose, the articulation handicap index (AHI) has been developed. Psychometric analyses referring to this index are presented here. The AHI was completed by 113 patients who had undergone treatment of tumours of the head or neck. The patients also gave a general self-assessment of their impairments due to articulation problems. Furthermore, tumour size, tumour location and kind of therapy were recorded. Missing data were analysed and replaced by multiple imputation. Internal structure was investigated using principal component analysis (PCA); reliability using Cronbach's alpha. Validity was investigated by analysing the relationship between AHI and general self-assessment of impairments. Moreover, the relationships with tumour size, tumour location and kind of therapy were analysed. Only 0.12 % of the answers to the AHI were missing. The Scree test performed with the PCA results suggested one-dimensionality with the first component explaining 49.6 % of the item variance. Cronbach's alpha was 0.96. Kendall's tau between the AHI sum score and the general self-assessment was 0.69. The intervals of AHI sum scores for the self-assessment categories were determined with 0-13 for no, 14-44 for mild, 46-76 for moderate, and 77-120 for severe impairment. The AHI sum score did not systematically relate to tumour size, tumour location or kind of therapy. The results are evidence for high acceptance, reliability and validity.

Numerical evaluation and optimization of depth-oriented temperature measurements for the investigation of thermal influences on groundwater

NASA Astrophysics Data System (ADS)

Köhler, Mandy; Haendel, Falk; Epting, Jannis; Binder, Martin; Müller, Matthias; Huggenberger, Peter; Liedl, Rudolf

2015-04-01

Increasing groundwater temperatures have been observed in many urban areas such as London (UK), Tokyo (Japan) and also in Basel (Switzerland). Elevated groundwater temperatures are a result of different direct and indirect thermal impacts. Groundwater heat pumps, building structures located within the groundwater and district heating pipes, among others, can be addressed to direct impacts, whereas indirect impacts result from the change in climate in urban regions (i.e. reduced wind, diffuse heat sources). A better understanding of the thermal processes within the subsurface is urgently needed for decision makers as a basis for the selection of appropriate measures to reduce the ongoing increase of groundwater temperatures. However, often only limited temperature data is available that derives from measurements in conventional boreholes, which differ in construction and instrumental setup resulting in measurements that are often biased and not comparable. For three locations in the City of Basel models were implemented to study selected thermal processes and to investigate if heat-transport models can reproduce thermal measurements. Therefore, and to overcome the limitations of conventional borehole measurements, high-resolution depth-oriented temperature measurement systems have been introduced in the urban area of Basel. In total seven devices were installed with up to 16 sensors which are located in the unsaturated and saturated zone (0.5 to 1 m separation distance). Measurements were performed over a period of 4 years (ongoing) and provide sufficient data to set up and calibrate high-resolution local numerical heat transport models which allow studying selected local thermal processes. In a first setup two- and three-dimensional models were created to evaluate the impact of the atmosphere boundary on groundwater temperatures (see EGU Poster EGU2013-9230: Modelling Strategies for the Thermal Management of Shallow Rural and Urban Groundwater bodies). For Basel, where the mean thickness of the unsaturated zone amounts to 19 m, it could be observed that atmospheric seasonal temperature variations are small compared to advective groundwater heat transport. At chosen locations: i) near the river Rhine to study river-groundwater interaction processes, ii) downstream of a thermal groundwater user who uses water for cooling and infiltrates water with elevated temperatures and iii) downstream of a building structure reaching into the groundwater saturated zone, models were further extended to study selected thermal processes in detail and to investigate if these models can reproduce thermal impacts in the vicinity of the temperature measurement devices. Calibration, based on the depth-oriented temperature measurements, was performed for the saturated and unsaturated zone, respectively. Model results show that, although depth-oriented measurements provide valuable insights into local thermal processes, the identification of the governing impacts is strongly dependent on an appropriate positioning of the measurement device. Numerical simulations based on existing flow- and heat transport models, considering the site specific local hydraulic and thermal boundary conditions, allow optimizing the location of such systems before installation. Furthermore, the results of the local heat transport models can be transferred to regional scale models which are an important tool for thermal management in urban areas.

Impact locations and concussion outcomes in high school football player-to-player collisions.

PubMed

Kerr, Zachary Y; Collins, Christy L; Mihalik, Jason P; Marshall, Stephen W; Guskiewicz, Kevin M; Comstock, R Dawn

2014-09-01

Little research has examined concussion outcomes in terms of impact location (ie, the area on the head in which the impact occurred). This study describes the epidemiology of concussions resulting from player-to-player collision in high school football by impact location. National High School Sports-Related Injury Surveillance Study data (2008/2009-2012/2013) were analyzed to calculate rates and describe circumstances of football concussion (eg, symptomology, symptom resolution time, return to play) resulting from player-to-player collisions by impact location (ie, front-, back-, side-, and top-of-the-head). Most concussions resulting from player-to-player collisions occurred from front-of-the-head (44.7%) and side-of-the-head (22.3%) impacts. Number of symptoms reported, prevalence of reported symptoms, symptom resolution time, and length of time to return to play were not associated with impact location. However, a larger proportion of football players sustaining concussions from top-of-the-head impacts experienced loss of consciousness (8.0%) than those sustaining concussions from impacts to other areas of the head (3.5%) (injury proportion ratio 2.3; 95% confidence interval 1.2-4.2; P = .008). Players had their head down at the time of impact in a higher proportion of concussions caused by top-of-the-head impacts (86.4%) than concussions from impacts to other areas of the head (24.0%) (injury proportion ratio 3.6; 95% confidence interval 3.2-4.0; P < .001). Among high school football players who sustained concussions due to player-to-player collisions, concussion outcomes were generally independent of impact location. Recommended strategies for reducing the proportion of top-of-the-head impacts include improved education regarding tackling with proper "head-up" technique. Copyright © 2014 by the American Academy of Pediatrics.

The Ewing Impact Structure: Progress Report

NASA Astrophysics Data System (ADS)

Abbott, D. H.; Nunes, A. A.; Leung, I. S.; Burckle, L.; Hagstrum, J. T.

2003-12-01

We have previously reported on the discovery of the Ewing impact structure. It is 150 km in diameter and is located in the equatorial Pacific between the Clarion and Clipperton fracture zones. We have now mapped the distribution of microtektites and other types of impact spherules. The microtektite bearing cores form a half circle to the south with a straight edge that passes through the center of the crater. This pattern of tektite distribution matches the pattern that has been modeled for deep-water impacts. The impact melt bodies that are the source of the magnetic anomalies associated with the crater also lie in the southern half of the crater. Thus, the overall pattern of microtektite and impact melt distribution is consistent with an impactor on an inclined trajectory that arrived from the north and sprayed ejecta to the south. We have found an impact melt bomb that is part of the distal ejecta blanket. The impact melt bomb is about 10 cm by 6 cm in size. It contains unmelted marine sediment in the center that is surrounded by impact melt glass. So far, attempts to date glassy spherules and impact melt glass have been unsuccessful. Thus, our best estimate of the age of the impact is derived from diatom biostratigraphy, which gives an age of 7 to 11 Ma. In this time period, there are three major climatic excursions that might be related to the Ewing impact event. In most of the region, the 5000-meter water depth precludes using the more numerous foraminiferal zones and oxygen isotope stratigraphy to more precisely date the ejecta layer. Detailed studies of the mineralogy of the ejecta layer in core PLDS-111P have failed to find any quartz at all, shocked or unshocked. However, this core received its ejecta from the southern half of the crater, where the pre-impact basement was composed of normal oceanic crust. To the north, a minor fracture zone cuts the crater. This fracture zone is a potential location of plagiogranites, which are quartz normative. The fracture zone also contains local topographic highs that are shallow enough to retain foraminifera. By concentrating our efforts on carbonate rich cores that sample the ejecta from the northern half of the crater on or near the fracture zone, we hope to determine a more accurate biostratigraphic age for the Ewing impact event. We will also examine the mineralogy of these samples to see if quartz or opaque minerals are present. Both quartz and some opaques can show characteristic shock deformation features.

Advances in Chemical and Structural Characterization of Concretion with Implications for Modeling Marine Corrosion

NASA Astrophysics Data System (ADS)

Johnson, Donald L.; DeAngelis, Robert J.; Medlin, Dana J.; Carr, James D.; Conlin, David L.

2014-05-01

The Weins number model and concretion equivalent corrosion rate methodology were developed as potential minimum-impact, cost-effective techniques to determine corrosion damage on submerged steel structures. To apply the full potential of these technologies, a detailed chemical and structural characterization of the concretion (hard biofouling) that transforms into iron bearing minerals is required. The fractions of existing compounds and the quantitative chemistries are difficult to determine from x-ray diffraction. Environmental scanning electron microscopy was used to present chemical compositions by means of energy-dispersive spectroscopy (EDS). EDS demonstrates the chemical data in mapping format or in point or selected area chemistries. Selected-area EDS data collection at precise locations is presented in terms of atomic percent. The mechanism of formation and distribution of the iron-bearing mineral species at specific locations will be presented. Based on water retention measurements, porosity in terms of void volume varies from 15 v/o to 30 v/o (vol.%). The void path displayed by scanning electron microscopy imaging illustrates the tortuous path by which oxygen migrates in the water phase within the concretion from seaside to metalside.

Distributed fiber optic strain sensing to detect artificial pitting corrosion in stirrups

NASA Astrophysics Data System (ADS)

Zhang, Jiachen; Kancharla, Vinutha; Hoult, Neil A.

2017-04-01

Pitting corrosion is difficult to identify through visual inspection and can lead to sudden structural failures. As such, an experimental study was undertaken to investigate whether distributed fiber optic strain sensors are capable of detecting the locations and strain changes associated with stirrup corrosion in reinforced concrete beams. In comparison to conventional strain gauges, this type of sensor can measure the strain response along the entire length of the fiber optic cable. Two specimens were tested: a control and a deteriorated beam. The deteriorated beam was artificially corroded by reducing the cross sectional area of the closed stirrups by 50% on both sides of the stirrup at the mid-height. This level of area reduction represents severe pitting corrosion. The beams were instrumented with nylon coated fiber optic sensors to measure the distributed strains, and then tested to failure under three point bending. The load deflection behavior of the two specimens was compared to assess the impact of the artificial pitting corrosion on the capacity. Digital Image Correlation was used to locate the extent and trajectory of the crack paths. It was found that the pitting corrosion had no impact on capacity or stiffness. Also, in this investigation the fiber optic sensing system failed to detect the location and strain changes due to pitting corrosion since the shear cracks did not intersect with the pitting location.

Numerical analysis of flow in a centrifugal compressor with circumferential grooves: influence of groove location and number on flow instability

NASA Astrophysics Data System (ADS)

Chen, X.; Qin, G.; Ai, Z.; Ji, Y.

2017-08-01

As an effective and economic method for flow range enhancement, circumferential groove casing treatment (CGCT) is widely used to increase the stall margin of compressors. Different from traditional grooved casing treatments, in which the grooves are always located over the rotor in both axial and radial compressors, one or several circumferential grooves are located along the shroud side of the diffuser passage in this paper. Numerical investigations were conducted to predict the performance of a low flow rate centrifugal compressor with CGCT in diffuser. Computational fluid dynamics (CFD) analysis is performed under stage environment in order to find the optimum location of the circumferential casing groove in consideration of stall margin enhancement and efficiency gain at design point, and the impact of groove number to the effect of this grooved casing treatment configuration in enhancing the stall margin of the compressor stage is studied. The results indicate that the centrifugal compressor with circumferential groove in vaned diffuser can obtain obvious improvement in the stall margin with sacrificing design efficiency a little. Efforts were made to study blade level flow mechanisms to determine how the CGCT impacts the compressor’s stall margin (SM) and performance. The flow structures in the passage, the tip gap, and the grooves as well as their mutual interactions were plotted and analysed.

Improving Deterministic Reserve Requirements for Security Constrained Unit Commitment and Scheduling Problems in Power Systems

NASA Astrophysics Data System (ADS)

Wang, Fengyu

Traditional deterministic reserve requirements rely on ad-hoc, rule of thumb methods to determine adequate reserve in order to ensure a reliable unit commitment. Since congestion and uncertainties exist in the system, both the quantity and the location of reserves are essential to ensure system reliability and market efficiency. The modeling of operating reserves in the existing deterministic reserve requirements acquire the operating reserves on a zonal basis and do not fully capture the impact of congestion. The purpose of a reserve zone is to ensure that operating reserves are spread across the network. Operating reserves are shared inside each reserve zone, but intra-zonal congestion may block the deliverability of operating reserves within a zone. Thus, improving reserve policies such as reserve zones may improve the location and deliverability of reserve. As more non-dispatchable renewable resources are integrated into the grid, it will become increasingly difficult to predict the transfer capabilities and the network congestion. At the same time, renewable resources require operators to acquire more operating reserves. With existing deterministic reserve requirements unable to ensure optimal reserve locations, the importance of reserve location and reserve deliverability will increase. While stochastic programming can be used to determine reserve by explicitly modelling uncertainties, there are still scalability as well as pricing issues. Therefore, new methods to improve existing deterministic reserve requirements are desired. One key barrier of improving existing deterministic reserve requirements is its potential market impacts. A metric, quality of service, is proposed in this thesis to evaluate the price signal and market impacts of proposed hourly reserve zones. Three main goals of this thesis are: 1) to develop a theoretical and mathematical model to better locate reserve while maintaining the deterministic unit commitment and economic dispatch structure, especially with the consideration of renewables, 2) to develop a market settlement scheme of proposed dynamic reserve policies such that the market efficiency is improved, 3) to evaluate the market impacts and price signal of the proposed dynamic reserve policies.

Integrated interpretation of geophysical data of the Paleozoic structure in the northwestern part of the Siljan Ring impact crater, central Sweden

NASA Astrophysics Data System (ADS)

Muhamad, Harbe; Juhlin, Christopher; Malehmir, Alireza; Sopher, Daniel

2018-01-01

The Siljan Ring impact structure is the largest known impact structure in Europe and is Late Devonian in age. It contains a central uplift that is about 20-30 km in diameter and is surrounded by a ring-shaped depression. The Siljan area is one of the few areas in Sweden where the Paleozoic sequence has not been completely eroded, making it an important location for investigation of the geological and tectonic history of Baltica during the Paleozoic. The Paleozoic strata in this area also provide insight into the complex deformation processes associated with the impact. In this study we focus on the northwestern part of the Siljan Ring, close to the town of Orsa, with the main objective of characterizing the subsurface Paleozoic succession and uppermost Precambrian crystalline rocks along a series of seismic reflection profiles, some of which have not previously been published. We combine these seismic data with gravity and magnetic data and seismic traveltime tomography results to produce an integrated interpretation of the subsurface in the area. Our interpretation shows that the Paleozoic sequence in this area is of a relatively constant thickness, with a total thickness typically between 300 and 500 m. Faulting appears to be predominantly extensional, which we interpret to have occurred during the modification stage of the impact. Furthermore, based on the geophysical data in this area, we interpret that the impact related deformation to differ in magnitude and style from other parts of the Siljan Ring.

Autonomous System for Monitoring the Integrity of Composite Fan Housings

NASA Technical Reports Server (NTRS)

Qing, Xinlin P.; Aquino, Christopher; Kumar, Amrita

2010-01-01

A low-cost and reliable system assesses the integrity of composite fan-containment structures. The system utilizes a network of miniature sensors integrated with the structure to scan the entire structural area for any impact events and resulting structural damage, and to monitor degradation due to usage. This system can be used to monitor all types of composite structures on aircraft and spacecraft, as well as automatically monitor in real time the location and extent of damage in the containment structures. This diagnostic information is passed to prognostic modeling that is being developed to utilize the information and provide input on the residual strength of the structure, and maintain a history of structural degradation during usage. The structural health-monitoring system would consist of three major components: (1) sensors and a sensor network, which is permanently bonded onto the structure being monitored; (2) integrated hardware; and (3) software to monitor in-situ the health condition of in-service structures.

A Study of Impact Point Detecting Method Based on Seismic Signal

NASA Astrophysics Data System (ADS)

Huo, Pengju; Zhang, Yu; Xu, Lina; Huang, Yong

The projectile landing position has to be determined for its recovery and range in the targeting test. In this paper, a global search method based on the velocity variance is proposed. In order to verify the applicability of this method, simulation analysis within the scope of four million square meters has been conducted in the same array structure of the commonly used linear positioning method, and MATLAB was used to compare and analyze the two methods. The compared simulation results show that the global search method based on the speed of variance has high positioning accuracy and stability, which can meet the needs of impact point location.

Determination of geostatistically representative sampling locations in Porsuk Dam Reservoir (Turkey)

NASA Astrophysics Data System (ADS)

Aksoy, A.; Yenilmez, F.; Duzgun, S.

2013-12-01

Several factors such as wind action, bathymetry and shape of a lake/reservoir, inflows, outflows, point and diffuse pollution sources result in spatial and temporal variations in water quality of lakes and reservoirs. The guides by the United Nations Environment Programme and the World Health Organization to design and implement water quality monitoring programs suggest that even a single monitoring station near the center or at the deepest part of a lake will be sufficient to observe long-term trends if there is good horizontal mixing. In stratified water bodies, several samples can be required. According to the guide of sampling and analysis under the Turkish Water Pollution Control Regulation, a minimum of five sampling locations should be employed to characterize the water quality in a reservoir or a lake. The European Union Water Framework Directive (2000/60/EC) states to select a sufficient number of monitoring sites to assess the magnitude and impact of point and diffuse sources and hydromorphological pressures in designing a monitoring program. Although existing regulations and guidelines include frameworks for the determination of sampling locations in surface waters, most of them do not specify a procedure in establishment of monitoring aims with representative sampling locations in lakes and reservoirs. In this study, geostatistical tools are used to determine the representative sampling locations in the Porsuk Dam Reservoir (PDR). Kernel density estimation and kriging were used in combination to select the representative sampling locations. Dissolved oxygen and specific conductivity were measured at 81 points. Sixteen of them were used for validation. In selection of the representative sampling locations, care was given to keep similar spatial structure in distributions of measured parameters. A procedure was proposed for that purpose. Results indicated that spatial structure was lost under 30 sampling points. This was as a result of varying water quality in the reservoir due to inflows, point and diffuse inputs, and reservoir hydromorphology. Moreover, hot spots were determined based on kriging and standard error maps. Locations of minimum number of sampling points that represent the actual spatial structure of DO distribution in the Porsuk Dam Reservoir

14 CFR 437.33 - Landing and impact locations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... each location for nominal landing or any contingency abort landing of the reusable suborbital rocket, and each location for any nominal or contingency impact or landing of a component of that rocket...

14 CFR 437.33 - Landing and impact locations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... each location for nominal landing or any contingency abort landing of the reusable suborbital rocket, and each location for any nominal or contingency impact or landing of a component of that rocket...

14 CFR 437.33 - Landing and impact locations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... each location for nominal landing or any contingency abort landing of the reusable suborbital rocket, and each location for any nominal or contingency impact or landing of a component of that rocket...

14 CFR 437.33 - Landing and impact locations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... each location for nominal landing or any contingency abort landing of the reusable suborbital rocket, and each location for any nominal or contingency impact or landing of a component of that rocket...

14 CFR 437.33 - Landing and impact locations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... each location for nominal landing or any contingency abort landing of the reusable suborbital rocket, and each location for any nominal or contingency impact or landing of a component of that rocket...

Aeroelastic analysis of an adaptive trailing edge with a smart elastic skin

NASA Astrophysics Data System (ADS)

Arena, Maurizio; Pecora, Rosario; Amoroso, Francesco; Noviello, Maria Chiara; Rea, Francesco; Concilio, Antonio

2017-09-01

Nowadays, the design choices of the new generation aircraft are moving towards the research and development of innovative technologies, aimed at improving performance as well as to minimize the environmental impact. In the current "greening" context, the morphing structures represent a very attractive answer to such requirements: both aerodynamic and structural advantages are ensured in several flight conditions, safeguarding the fuel consumption at the same time. An aeronautical intelligent system is therefore the outcome of combining complex smart materials and structures, assuring the best functionality level in the flight envelope. The Adaptive Trailing Edge Device (ATED) is a sub-project inside SARISTU (Smart Intelligent Aircraft Structures), an L2 level project of the 7th EU Framework programme coordinated by Airbus, aimed at developing technologies for realizing a morphing wing extremity addressed to improve the general aircraft performance and to reduce the fuel burning up to 5%. This specific study, divided into design, manufacturing and testing phases, involved universities, research centers and leading industries of the European consortium. The paper deals with the aeroelastic impact assessment of a full-scale morphing wing trailing edge on a Large Aeroplanes category aircraft. The FE (Finite Element) model of the technology demonstrator, located in the aileron region and manufactured within the project, was referenced to for the extrapolation of the structural properties of the whole adaptive trailing edge device placed in its actual location in the outer wing. The input FE models were processed within MSC-Nastran® environment to estimate stiffness and inertial distributions suitable to construct the aeroelastic stick-beam mock-up of the reference structure. Afterwards, a flutter analysis in simulated operative condition, have been carried out by means of Sandy®, an in-house code, according to meet the safety requirements imposed by the applicable aviation regulations (paragraph 25.629, parts (a) and (b)-(1)).

Intrahepatic, peri-hilar and distal cholangiocarcinoma: Three different locations of the same tumor or three different tumors?

PubMed

Ercolani, G; Dazzi, A; Giovinazzo, F; Ruzzenente, A; Bassi, C; Guglielmi, A; Scarpa, A; D'Errico, A; Pinna, A D

2015-09-01

Few papers deal with pathologic characteristics and outcome of the 3 different cholangiocarcinomas based on location (intrahepatic, peri-hilar, distal). There is little evidence regarding similarity and differences. From two tertiary referral Italian Centers (in Bologna and Verona), 479 patients with cholangiocarcinoma were evaluated between 1980 and 2011. Several pathologic characteristics and their impact on survival were analyzed among resected patients for cholangiocarcinomas depending on the site of origin. Tumour location was intrahepatic in 172 cases (36%), peri-hilar in 243 (51) and distal in 64(13%). Curative resection was performed in 339 (70%) patients. Intrahepatic cholangiocarcinoma showed higher probability to achieve R0 resection (81%), but was more frequently associated with presence of microvascular invasion (71%). Distal cholangiocarcinoma presented less R0 resections (58%), higher lymphnode involvement (60%) and lower microvascular invasion (49%). Hilar cholangiocarcinoma had intermediate characteristics (R0: 65% of cases). Median follow up was 30.2 ± 38 months; the 5 years overall survival was 31% in the resected population. Overall survival curves were similar among the three groups. At univariate analysis surgical margins, lymphnode status, perineural invasion, T category, TNM stage, microvascular invasion, tumour grading had significant impact on survival. At multivariate analysis, only microvascular invasion was significantly related to long term results (HR = 1,7; 95% CI = 1,0-2,5)". Micro-vascular invasion has the strongest impact on survival in all three types of cholangiocarcinoma. In case of comparable pathologic characteristics and stage, the three tumors show similar outcome; depending on location, it shows a different tendency to invade bordering structures which affect the outcome. Copyright © 2015 Elsevier Ltd. All rights reserved.

Testing the lexical hypothesis: are socially important traits more densely reflected in the English lexicon?

PubMed

Wood, Dustin

2015-02-01

Using a set of 498 English words identified by Saucier (1997) as common person-descriptor adjectives or trait terms, I tested 3 instantiations of the lexical hypothesis, which posit that more socially important person descriptors show greater density in the lexicon. Specifically, I explored whether trait terms that have greater relational impact (i.e., more greatly influence how others respond to a person) have more synonyms, are more frequently used, and are more strongly correlated with other trait terms. I found little evidence to suggest that trait terms rated as having greater relational impact were more frequently used or had more synonyms. However, these terms correlated more strongly with other trait terms in the set. Conversely, a trait term's loadings on structural factors (e.g., the Big Five, HEXACO) were extremely good predictors of the term's relational impact. The findings suggest that the lexical hypothesis may not be strongly supported in some ways it is commonly understood but is supported in the manner most important to investigations of trait structure. Specifically, trait terms with greater relational impact tend to more strongly correlate with other terms in lexical sets and thus have a greater role in driving the location of factors in analyses of trait structure. Implications for understanding the meaning of lexical factors such as the Big Five are discussed. PsycINFO Database Record (c) 2015 APA, all rights reserved.

Shuttle Hypervelocity Impact Database

NASA Technical Reports Server (NTRS)

Hyde, James L.; Christiansen, Eric L.; Lear, Dana M.

2011-01-01

With three missions outstanding, the Shuttle Hypervelocity Impact Database has nearly 3000 entries. The data is divided into tables for crew module windows, payload bay door radiators and thermal protection system regions, with window impacts compromising just over half the records. In general, the database provides dimensions of hypervelocity impact damage, a component level location (i.e., window number or radiator panel number) and the orbiter mission when the impact occurred. Additional detail on the type of particle that produced the damage site is provided when sampling data and definitive analysis results are available. Details and insights on the contents of the database including examples of descriptive statistics will be provided. Post flight impact damage inspection and sampling techniques that were employed during the different observation campaigns will also be discussed. Potential enhancements to the database structure and availability of the data for other researchers will be addressed in the Future Work section. A related database of returned surfaces from the International Space Station will also be introduced.

Comparison of Hard Surface and Soft Soil Impact Performance of a Crashworthy Composite Fuselage Concept

NASA Technical Reports Server (NTRS)

Sareen, Ashish K.; Sparks, Chad; Mullins, B. R., Jr.; Fasanella, Edwin; Jackson, Karen

2002-01-01

A comparison of the soft soil and hard surface impact performance of a crashworthy composite fuselage concept has been performed. Specifically, comparisons of the peak acceleration values, pulse duration, and onset rate at specific locations on the fuselage were evaluated. In a prior research program, the composite fuselage section was impacted at 25 feet per second onto concrete at the Impact Dynamics Research Facility (IDRF) at NASA Langley Research Center. A soft soil test was conducted at the same impact velocity as a part of the NRTC/RITA Crashworthy and Energy Absorbing Structures project. In addition to comparisons of soft soil and hard surface test results, an MSC. Dytran dynamic finite element model was developed to evaluate the test analysis correlation. In addition, modeling parameters and techniques affecting test analysis correlation are discussed. Once correlated, the analytical methodology will be used in follow-on work to evaluate the specific energy absorption of various subfloor concepts for improved crash protection during hard surface and soft soil impacts.

Analysis of SVC’s Impact on Out-of-step Oscillation Based on Direct Method Considering Admittance Effect

NASA Astrophysics Data System (ADS)

He, Jing-bo; Ding, Jian; Feng, Li; Ren, Jian-wen; Tang, Wei; Yang, Cheng; Wang, Jing-jin; Song, Yun-ting

2017-05-01

The widely employment of power electronic equipment in modern power system, may affect grid structure and system operation because of their diverse dynamic characteristics. In this paper, the impact of the static var compensators (SVC) on out-of-step oscillation is investigated based on the equal area criterion by considering SVC’s admittance effect. Firstly, the variation pattern of bus voltage which is connected to SVC is concluded. Then the derivation of equation considering the admittance effect is given, which explains the ability of SVC to suppress out-of-step oscillation. SVC’s impact on migration of out-of-step oscillation centre (OSOC) is discussed based on the expression of OSOC’s electrical location. Moreover, the influence of SVC’s response speed and capacity on its effect are presented by qualitative analysis. Finally, simulations on a two-end equivalent test system are carried out to verify the correctness of the theoretical analysis. It is found that the capacity and a response speed of SVC have significant effect on the out-of-step oscillation, while SVC have no d istinct influence on location of OSOC.

Analysis of Geodynamical Conditions of Region of Burning Coal Dumps Location

NASA Astrophysics Data System (ADS)

Batugin, Andrian; Musina, Valeria; Golovko, Irina

2017-12-01

Spontaneous combustion of coal dumps and their impact on the environment of mining regions remain important environmental problem, in spite of the measures that are being taken. The paper presents the hypothesis, which states that the location of coal dumps at the boundaries of geodynamically active crust blocks promotes the appearance of conditions for their combustion. At present geodynamically active crust faults that affect the operating conditions of engineering facilities are observed not only in the areas of tectonic activity, but also on platforms. According to the concept of geodynamical zoning, geodynamically dangerous zones for engineering structures can be not only large, well-developed crust faults, but also just formed fractures that appear as boundaries of geodynamically impacting and hierarchically ordered crust blocks. The purpose of the study is to estimate the linkage of burning dumps to boundaries of geodynamically active crust blocks (geodynamically dangerous zones) for subsequent development of recommendations for reducing environmental hazard. The analysis of 27 coal dumps location was made for one of the Eastern Donbass regions (Russia). Nine of sixteen burning dumps are located in geodynamically dangerous zones, which, taking into account relatively small area occupied by all geodynamically dangerous zones, results that there is a concentration (pcs/km2) of burning dumps, which is 14 times higher than the baseline value. While the probability of accidental obtaining of such a result is extremely low, this can be considered as the evidence of the linkage of burning dumps to geodynamically dangerous zones. Taking into account the stressed state of the rock massif in this region, all geodynamically dangerous zones can be divided into compression and tension zones. The statistic is limited, but nevertheless in tension zones the concentration of burning dumps is 2 times higher than in compression zones. Available results of thermal monitoring of burning dumps in this region also show that linearly extended firing sources oriented along geodynamically dangerous zones are observed. The obtained results show that geodynamical conditions of mining region, in which coal dumps are located, is important factor that impacts the creation of conditions for their spontaneous combustion and subsequent impact on the environment. Then this factor should be controlled by choosing the place for dumps location. It is proposed to carry out these works for the entire mining region of the Eastern Donbass, where there are more than 200 coal dumps.

Damage Characterization Method for Structural Health Management Using Reduced Number of Sensor Inputs

NASA Technical Reports Server (NTRS)

Krishnamurthy, T.; Hochhalter, Jacob D.; Gallegos, Adam M.

2012-01-01

The development of validated multidisciplinary Integrated Vehicle Health Management (IVHM) tools, technologies, and techniques to enable detection, diagnosis, prognosis, and mitigation in the presence of adverse conditions during flight will provide effective solutions to deal with safety related challenges facing next generation aircraft. The adverse conditions include loss of control caused by environmental factors, actuator and sensor faults or failures, and damage conditions. A major concern in these structures is the growth of undetected damage (cracks) due to fatigue and low velocity foreign impacts that can reach a critical size during flight, resulting in loss of control of the aircraft. Hence, development of efficient methodologies to determine the presence, location, and severity of damage in critical structural components is highly important in developing efficient structural health management systems.

Damage Characterization Using the Extended Finite Element Method for Structural Health Management

NASA Technical Reports Server (NTRS)

Krishnamurthy, Thiagarajan; Gallegos, Adam M.

2011-01-01

The development of validated multidisciplinary Integrated Vehicle Health Management (IVHM) tools, technologies, and techniques to enable detection, diagnosis, prognosis, and mitigation in the presence of adverse conditions during flight will provide effective solutions to deal with safety related challenges facing next generation aircraft. The adverse conditions include loss of control caused by environmental factors, actuator and sensor faults or failures, and damage conditions. A major concern in these structures is the growth of undetected damage/cracks due to fatigue and low velocity foreign impact that can reach a critical size during flight, resulting in loss of control of the aircraft. Hence, development of efficient methodologies to determine the presence, location, and severity of damage/cracks in critical structural components is highly important in developing efficient structural health management systems.

Modeling of the Central Magnetic Anomaly at Haughton Impact Structure, Canada

NASA Astrophysics Data System (ADS)

Quesnel, Y.; Gattacceca, J.; Osinski, G. R.; Rochette, P.

2011-12-01

Located on Devon Island, Nunavut, Canada, the 23-km diameter Haughton impact structure is one of the best-preserved medium-size complex impact structures on Earth. The impact occurred ~39 Ma ago into a target formation composed of an ~2-km thick sequence of Lower Paleozoic sedimentary rocks of the Arctic Platform overlying Precambrian metamorphic basement of the Canadian Shield (Osinski et al., 2005). Clast-rich impact melt rocks line the crater and impact-induced hydrothermal activity took place, but since then no significant geological event has affected the area. In the 1980s, ground magnetic and gravity measurements were carried out within the central part of the crater (Pohl et al., 1988). A significant anomaly was discovered and coarsely modeled by a source body of simple geometry. More recently, an airborne magnetic survey delivered additional data that covered the whole crater but no modeling was done (Glass et al., 2002). Here, we present the results of a new ground magnetic survey accompanied by rock magnetic property measurements made on all samples of the crater. This has provided additional constraints to investigate the origin of this central magnetic anomaly. By conducting modeling, we have been able to reveal the geometry and volume of the source body as well as its magnetization properties. Our results suggest that the necessary magnetization intensity to account for this anomaly is too large to be associated with uplifted pre-impact target rocks. Therefore, we suggest that hydrothermal alteration could have enhanced the magnetization of the central part of this crater. References : Osinski, G. R. et al. 2005. MPS, 40:1759-1776 ; Pohl, J. et al. 1988. Meteoritics, 23:235-238 ; Glass, B. J. et al. 2002, Abstract #2008. 33th LPSC

Petrology of Impact-Melt Rocks at the Chicxulub Multiring Basin, Yucatan, Mexico

NASA Technical Reports Server (NTRS)

Schuraytz, Benjamin C.; Sharpton, Virgil L.; Marin, Luis E.

1994-01-01

Compositions and textures of melt rocks from the upper part of the Chicxulub structure are typical of melt rocks at other large terrestrial impact structures. Apart from variably elevated iridium concentrations (less than 1.5 to 13.5 +/- 0.9 ppb) indicating nonuniform dissemination of a meteoritic component, bulk rock and phenocryst compositions imply that these melt rocks were derived exclusively from continental crust and platform-sediment target lithologies. Modest differences in bulk chemistry among samples from wells located approximately 40 km apart suggest minor variations in relative contributions of these target lithologies to the melts. Subtle variations in the compositions of early-formed pyroxene and plagioclase also support minor primary differences in chemistry between the melts. Evidence for pervasive hydrothermal alteration of the porous mesostasis includes albite, K-feldspar, quartz, epidote, chlorite, and other phyllosilicates, as well as siderophile element-enriched sulfides, suggesting the possibility that Chicxulub, like Sudbury, may host important ore deposits.

ARC-1980-A80-7034

NASA Image and Video Library

1980-11-12

Range : 660,000 kilometers (400,000 miles) Time : 5:05 am PST This Voyager 1 picture of Mimas shows a large impact structure at 110 degrees W Long., located on that face of the moon which leads Mimas in its orbit. The feature, about 130 kilometers in diameter (80 miles), is more than 1/4 the diameter of the entire moon. This is a particularly interesting feature in view of its large diameter compared with the size of the satellite, and may have the largest crater diameter/satillite diameter ratio in the solar system. The crater has a raised rim and central peak, typical of large impact structures on terrestrial planets. Additional smaller craters, 15-45 kilometers in diameter, can be seen scattered across the surface, particularly alon the terminator. Mimas is one of the smaller Saturnian satellites with a low density implying its chief component is ice.

Recent Developments in Ground-Borne Noise and Vibration Control

NASA Astrophysics Data System (ADS)

Nelson, J. T.

1996-05-01

Vibration control provisions available to the transit designer include (among others) precision straightened rail, ballast mats, floating slabs and very soft direct fixation fasteners, in addition to rail grinding, wheel truing, and continuous welded rail. Recently, the Los Angeles Metro has developed specifications for a soft resilient direct fixation fastener to fit the same base dimensions as the standard direct fixation fastener. In San Francisco, low resonance frequency (8 Hz) floating slabs have been constructed to mitigate predicted ground vibration impacts at nearby residential structures. In Atlanta, low resonance frequency loading slabs have been constructed to maintain a low vibration environment in a medical building planned to be built over the subway structure. In Portland and Pasadena, ballast mats have been recommended to control light rail transit ground vibration impacts on housing located at typically 35 feet from the alignment. Each of these provisions are briefly described in view of recent applications at U.S. transit systems.

Influence of electromechanical coupling on optical properties of InGaN quantum-dot based light-emitting diodes.

PubMed

Barettin, Daniele; Maur, Matthias Auf der; Carlo, Aldo di; Pecchia, Alessandro; Tsatsulnikov, Andrei F; Sakharov, Alexei V; Lundin, Wsevolod V; Nikolaev, Andrei E; Usov, Sergey O; Cherkashin, Nikolay; Hÿtch, Martin J; Karpov, Sergey Yu

2017-01-06

The impact of electromechanical coupling on optical properties of light-emitting diodes (LEDs) with InGaN/GaN quantum-dot (QD) active regions is studied by numerical simulations. The structure, i.e. the shape and the average In content of the QDs, has been directly derived from experimental data on out-of-plane strain distribution obtained from the geometric-phase analysis of a high-resolution transmission electron microscopy image of an LED structure grown by metalorganic vapor-phase epitaxy. Using continuum [Formula: see text] calculations, we have studied first the lateral and full electromechanical coupling between the QDs in the active region and its impact on the emission spectrum of a single QD located in the center of the region. Our simulations demonstrate the spectrum to be weakly affected by the coupling despite the strong common strain field induced in the QD active region. Then we analyzed the effect of vertical coupling between vertically stacked QDs as a function of the interdot distance. We have found that QCSE gives rise to a blue-shift of the overall emission spectrum when the interdot distance becomes small enough. Finally, we compared the theoretical spectrum obtained from simulation of the entire active region with an experimental electroluminescence (EL) spectrum. While the theoretical peak emission wavelength of the selected central QD corresponded well to that of the EL spectrum, the width of the latter one was determined by the scatter in the structures of various QDs located in the active region. Good agreement between the simulations and experiment achieved as a whole validates our model based on realistic structure of the QD active region and demonstrates advantages of the applied approach.

Variations in grain-scale sediment structure and entrainment force in a gravel-bed channel as a function of fine sediment content and morphological location

NASA Astrophysics Data System (ADS)

Voepel, Hal; Ahmed, Sharif; Hodge, Rebecca; Leyland, Julian; Sear, David

2017-04-01

One of the major causes of uncertainty in estimates of bedload transport rates in gravel-bed rivers is a lack of understanding of grain-scale sediment structure, and the impact that this structure has on the force required to entrain sediment. There are at least two factors that standard entrainment models do not consider. The first is the way in which the spatial arrangement and orientation of grains and the resultant forces varies throughout a channel and over time, ways that have yet to be fully quantified. The second is that sediment entrainment is a 3D process, yet calculations of entrainment thresholds for sediment grains are typically based on 2D diagrams where we calculate static moments of force vectors about a pivot angle, represented as a single point rather than as a more realistic axis of rotation. Our research addresses these limitations by quantifying variations in 3D sediment structure and entrainment force requirements across two key parameters: morphological location within a riffle-pool sequence (reflecting variation in hydraulic conditions), and the fine sediment content of the gravel-bed (sand and clay). We report results from a series of flume experiments in which we water-worked a gravel-bed with a riffle-pool morphology containing varying amounts of fine sediment. After each experimental run intact samples of the bed at different locations were extracted and the internal structure of the bed was measured using non-destructive, micro-focus X-ray computed tomography (CT) imaging. The CT images were processed to measure the properties of individual grains, including volume, center of mass, dimension, and contact points. From these data we were able to quantify the sediment structure and entrainment force requirements through measurement of 3D metrics including grain pivot angles, grain exposure and protrusion. Comparison of the metrics across different morphological locations and fine sediment content demonstrates how these factors affect the bed structure and entrainment force requirement. These results have implications for the development of sediment entrainment models for gravel-bed rivers. Keywords: fluvial sediment, geomorphology, entrainment models, X-ray computed tomography, 3D imaging, vector mechanics

A model-based approach to determine the long-term effects of multiple interacting stressors on coral reefs.

PubMed

Blackwood, Julie C; Hastings, Alan; Mumby, Peter J

2011-10-01

The interaction between multiple stressors on Caribbean coral reefs, namely, fishing effort and hurricane impacts, is a key element in the future sustainability of reefs. We develop an analytic model of coral-algal interactions and explicitly consider grazing by herbivorous reef fish. Further, we consider changes in structural complexity, or rugosity, in addition to the direct impacts of hurricanes, which are implemented as stochastic jump processes. The model simulations consider various levels of fishing effort corresponding to' several hurricane frequencies and impact levels dependent on geographic location. We focus on relatively short time scales so we do not explicitly include changes in ocean temperature, chemistry, or sea level rise. The general features of our approach would, however, apply to these other stressors and to the management of other systems in the face of multiple stressors. It is determined that the appropriate management policy, either local reef restoration or fisheries management, greatly depends on hurricane frequency and impact level. For sufficiently low hurricane impact and macroalgal growth rate, our results indicate that regions with lower-frequency hurricanes require stricter fishing regulations, whereas management in regions with higher-frequency hurricanes might be less concerned with enhancing grazing and instead consider whether local-scale restorative activities to increase vertical structure are cost-effective.

14 CFR 437.61 - Landing and impact locations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... locations. For a nominal or any contingency abort landing of a reusable suborbital rocket, or for any nominal or contingency impact or landing of a component of that rocket, a permittee must use a location...

14 CFR 437.61 - Landing and impact locations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... locations. For a nominal or any contingency abort landing of a reusable suborbital rocket, or for any nominal or contingency impact or landing of a component of that rocket, a permittee must use a location...

14 CFR 437.61 - Landing and impact locations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... locations. For a nominal or any contingency abort landing of a reusable suborbital rocket, or for any nominal or contingency impact or landing of a component of that rocket, a permittee must use a location...

14 CFR 437.61 - Landing and impact locations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... locations. For a nominal or any contingency abort landing of a reusable suborbital rocket, or for any nominal or contingency impact or landing of a component of that rocket, a permittee must use a location...

14 CFR 437.61 - Landing and impact locations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... locations. For a nominal or any contingency abort landing of a reusable suborbital rocket, or for any nominal or contingency impact or landing of a component of that rocket, a permittee must use a location...

A single geophone to locate seismic events on Mars

NASA Astrophysics Data System (ADS)

Roques, Aurélien; Berenguer, Jean-Luc; Bozdag, Ebru

2016-04-01

Knowing the structure of Mars is a key point in understanding the formation of Earth-like planets as plate tectonics and erosion have erased the original suface of the Earth formation. Installing a seismometer on Mars surface makes it possible to identify its structure. An important step in the identification of the structure of a planet is the epicenter's location of a seismic source, typically a meteoric impact or an earthquake. On Earth, the classical way of locating epicenters is triangulation, which requires at least 3 stations. The Mars InSight Project plans to set a single station with 3 components. We propose a software to locate seismic sources on Mars thanks to the 3-components simulated data of an earthquake given by Geoazur (Nice Sophia-Antipolis University, CNRS) researchers. Instrumental response of a sensor is crucial for data interpretation. We study the oscillations of geophone in several situations so as to awaken students to the meaning of damping in second order modeling. In physics, car shock absorbers are often used to illustrate the principle of damping but rarely in practical experiments. We propose the use of a simple seismometer (a string with a mass and a damper) that allows changing several parameters (inductive damping, temperature and pressure) so as to see the effects of these parameters on the impulse response and, in particular, on the damping coefficient. In a second step, we illustrate the effect of damping on a seismogram with the difficulty of identifying and interpreting the different phase arrival times with low damping.

An Impact-Location Estimation Algorithm for Subsonic Uninhabited Aircraft

NASA Technical Reports Server (NTRS)

Bauer, Jeffrey E.; Teets, Edward

1997-01-01

An impact-location estimation algorithm is being used at the NASA Dryden Flight Research Center to support range safety for uninhabited aerial vehicle flight tests. The algorithm computes an impact location based on the descent rate, mass, and altitude of the vehicle and current wind information. The predicted impact location is continuously displayed on the range safety officer's moving map display so that the flightpath of the vehicle can be routed to avoid ground assets if the flight must be terminated. The algorithm easily adapts to different vehicle termination techniques and has been shown to be accurate to the extent required to support range safety for subsonic uninhabited aerial vehicles. This paper describes how the algorithm functions, how the algorithm is used at NASA Dryden, and how various termination techniques are handled by the algorithm. Other approaches to predicting the impact location and the reasons why they were not selected for real-time implementation are also discussed.

A multi-scale metrics approach to forest fragmentation for Strategic Environmental Impact Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Eunyoung, E-mail: eykim@kei.re.kr; Song, Wonkyong, E-mail: wksong79@gmail.com; Lee, Dongkun, E-mail: dklee7@snu.ac.kr

Forests are becoming severely fragmented as a result of land development. South Korea has responded to changing community concerns about environmental issues. The nation has developed and is extending a broad range of tools for use in environmental management. Although legally mandated environmental compliance requirements in South Korea have been implemented to predict and evaluate the impacts of land-development projects, these legal instruments are often insufficient to assess the subsequent impact of development on the surrounding forests. It is especially difficult to examine impacts on multiple (e.g., regional and local) scales in detail. Forest configuration and size, including forest fragmentationmore » by land development, are considered on a regional scale. Moreover, forest structure and composition, including biodiversity, are considered on a local scale in the Environmental Impact Assessment process. Recently, the government amended the Environmental Impact Assessment Act, including the SEA, EIA, and small-scale EIA, to require an integrated approach. Therefore, the purpose of this study was to establish an impact assessment system that minimizes the impacts of land development using an approach that is integrated across multiple scales. This study focused on forest fragmentation due to residential development and road construction sites in selected Congestion Restraint Zones (CRZs) in the Greater Seoul Area of South Korea. Based on a review of multiple-scale impacts, this paper integrates models that assess the impacts of land development on forest ecosystems. The applicability of the integrated model for assessing impacts on forest ecosystems through the SEIA process is considered. On a regional scale, it is possible to evaluate the location and size of a land-development project by considering aspects of forest fragmentation, such as the stability of the forest structure and the degree of fragmentation. On a local scale, land-development projects should consider the distances at which impacts occur in the vicinity of the forest ecosystem, and these considerations should include the impacts on forest vegetation and bird species. Impacts can be mitigated by considering the distances at which these influences occur. In particular, this paper presents an integrated environmental impact assessment system to be applied in the SEIA process. The integrated assessment system permits the assessment of the cumulative impacts of land development on multiple scales. -- Highlights: • The model is to assess the impact of forest fragmentation across multiple scales. • The paper suggests the type of forest fragmentation on a regional scale. • The type can be used to evaluate the location and size of a land development. • The paper shows the influence distance of land development on a local scale. • The distance can be used to mitigate the impact at an EIA process.« less

Interactions between the spatial and temporal stimulus factors that influence multisensory integration in human performance.

PubMed

Stevenson, Ryan A; Fister, Juliane Krueger; Barnett, Zachary P; Nidiffer, Aaron R; Wallace, Mark T

2012-05-01

In natural environments, human sensory systems work in a coordinated and integrated manner to perceive and respond to external events. Previous research has shown that the spatial and temporal relationships of sensory signals are paramount in determining how information is integrated across sensory modalities, but in ecologically plausible settings, these factors are not independent. In the current study, we provide a novel exploration of the impact on behavioral performance for systematic manipulations of the spatial location and temporal synchrony of a visual-auditory stimulus pair. Simple auditory and visual stimuli were presented across a range of spatial locations and stimulus onset asynchronies (SOAs), and participants performed both a spatial localization and simultaneity judgment task. Response times in localizing paired visual-auditory stimuli were slower in the periphery and at larger SOAs, but most importantly, an interaction was found between the two factors, in which the effect of SOA was greater in peripheral as opposed to central locations. Simultaneity judgments also revealed a novel interaction between space and time: individuals were more likely to judge stimuli as synchronous when occurring in the periphery at large SOAs. The results of this study provide novel insights into (a) how the speed of spatial localization of an audiovisual stimulus is affected by location and temporal coincidence and the interaction between these two factors and (b) how the location of a multisensory stimulus impacts judgments concerning the temporal relationship of the paired stimuli. These findings provide strong evidence for a complex interdependency between spatial location and temporal structure in determining the ultimate behavioral and perceptual outcome associated with a paired multisensory (i.e., visual-auditory) stimulus.

Museum Institutions in Monuments - Positive and Negative Aspects of Adaptation: The New Amber Museum and Museum of Science in Gdansk, Poland

NASA Astrophysics Data System (ADS)

Piatkowska, Ksenia

2017-10-01

The issue of the creation and location of new museums is a current topic. The decision of where and how to create new museum facilities will impact successful function in the future. Museums are either located in newly designed buildings or in existing buildings. In general, existing buildings adapted for museum use are either formally under conservational protection or not. With regard to museum location in preserved monuments, the author notes that the true impact on authentic monumental building structure still needs intense research. The adaptation of the Great Mill and St. Catherine’s Church - two preserved medieval objects located in the historical city center of Gdansk - provide case studies to investigate positive and negative aspects. In both cases, the author carried out architectural projects for the functional purposes of museums: The New Amber Museum and Museum of Science. The author concludes that mutual benefits of adaptation result from: the financial means of the museum institution to invest long-term; the institutional respect of the museum towards heritage, which translates into respect for conservational protection; and the competitive advantage created by the monumental features of the building and the privileged location in a well-established, branded space. Negative aspects result from: space limitations of monuments that disable the museum from extending its exposition and thus prevent institutional development; the overly restrictive requirements of restoration that take priority over the museum mission; and the lack of technically functional space required for contemporary museum technologies, which forces unconventional engineering solutions that are more expensive than the location of the museum in a newly constructed building.

Application of low-coherence interferometry for in situ nondestructive evaluation of thin and thick multilayered transparent composites

NASA Astrophysics Data System (ADS)

Khomenko, Anton; Cloud, Gary Lee; Haq, Mahmoodul

2015-12-01

Multilayered transparent composites having laminates with polymer interlayers and backing sheets are commonly used in a wide range of applications where visibility, transparency, impact resistance, and safety are essential. Manufacturing flaws or damage during operation can seriously compromise both safety and performance. Most fabrication defects are not discernible until after the entire multilayered transparent composite assembly has been completed, and in-the-field inspection for damage is a problem not yet solved. A robust and reliable nondestructive evaluation (NDE) technique is needed to evaluate structural integrity and identify defects that result from manufacturing issues as well as in-service damage arising from extreme environmental conditions in addition to normal mechanical and thermal loads. Current optical techniques have limited applicability for NDE of such structures. This work presents a technique that employs a modified interferometer utilizing a laser diode or femtosecond fiber laser source to acquire in situ defect depth location inside a thin or thick multilayered transparent composite, respectively. The technique successfully located various defects inside examined composites. The results show great potential of the technique for defect detection, location, and identification in multilayered transparent composites.

Impact direction effect on serious-to-fatal injuries among drivers in near-side collisions according to impact location: focus on thoracic injuries.

PubMed

Lai, Xinghua; Ma, Chunsheng; Hu, Jingwen; Zhou, Qing

2012-09-01

Occupant injury in real world vehicle accidents can be significantly affected by a set of crash characteristics, of which impact direction and impact location (or damage location) in general scale interval (e.g., frontal impact is frequently defined as general damage to vehicle frontal end with impact angle range of 11-1 o'clock) have been identified to associate with injury outcome. The effects of crash configuration in more specific scale of interval on the injury characteristics have not been adequately investigated. This paper presents a statistical analysis to investigate the combined effects of specific impact directions and impact locations on the serious-to-fatal injuries of driver occupants involved in near-side collisions using crash data from National Automotive Sampling System-Crashworthiness Data System (NASS-CDS) for the calendar years of 1995-2005. The screened injury dataset is categorized by three impact locations (side front, side center and side distributed) and two impact directions (oblique impact at 10 o'clock and pure lateral impact at 9 o'clock), resulting in six crash configurations in total. The weighted counts and the risks of different types of injuries in each subgroup are calculated, with which the relative risks along with 95% confidence intervals under oblique impacts versus lateral impacts in each impact location category are computed. Accordingly, the most frequent injury patterns, the risks and the coded-sources of serious thoracic injuries in different crash configurations are identified. The approach adopted in the present study provides new perspectives into occupant injury outcomes and associated mechanism. Results of the analyses reveal the importance of consideration of the crash configurations beyond the scope of existing side-impact regulatory tests and stress the necessity of vehicle crashworthiness and restraint system design in omni-direction to better protect occupants in real-world crash scenarios. Copyright © 2012 Elsevier Ltd. All rights reserved.

Dependency of high coastal water level and river discharge at the global scale

NASA Astrophysics Data System (ADS)

Ward, P.; Couasnon, A.; Haigh, I. D.; Muis, S.; Veldkamp, T.; Winsemius, H.; Wahl, T.

2017-12-01

It is widely recognized that floods cause huge socioeconomic impacts. From 1980-2013, global flood losses exceeded $1 trillion, with 220,000 fatalities. These impacts are particularly hard felt in low-lying densely populated deltas and estuaries, whose location at the coast-land interface makes them naturally prone to flooding. When river and coastal floods coincide, their impacts in these deltas and estuaries are often worse than when they occur in isolation. Such floods are examples of so-called `compound events'. In this contribution, we present the first global scale analysis of the statistical dependency of high coastal water levels (and the storm surge component alone) and river discharge. We show that there is statistical dependency between these components at more than half of the stations examined. We also show time-lags in the highest correlation between peak discharges and coastal water levels. Finally, we assess the probability of the simultaneous occurrence of design discharge and design coastal water levels, assuming both independence and statistical dependence. For those stations where we identified statistical dependency, the probability is between 1 and 5 times greater, when the dependence structure is accounted for. This information is essential for understanding the likelihood of compound flood events occurring at locations around the world as well as for accurate flood risk assessments and effective flood risk management. The research was carried out by analysing the statistical dependency between observed coastal water levels (and the storm surge component) from GESLA-2 and river discharge using gauged data from GRDC stations all around the world. The dependence structure was examined using copula functions.

Pathways between under/unemployment and health among racialized immigrant women in Toronto.

PubMed

Premji, Stephanie; Shakya, Yogendra

2017-02-01

We sought to document pathways between under/unemployment and health among racialized immigrant women in Toronto while exploring the ways in which gender, class, migration and racialization, as interlocking systems of social relations, structure these relationships. We conducted 30 interviews with racialized immigrant women who were struggling to get stable employment that matched their education and/or experience. Participants were recruited through flyers, partner agencies and peer researcher networks. Most interviews (21) were conducted in a language other than English. Interviews were transcribed, translated as appropriate and analyzed using NVivo software. The project followed a community-based participatory action research model. Under/unemployment negatively impacted the physical and mental health of participants and their families. It did so directly, for example through social isolation, as well as indirectly through representation in poor quality jobs. Under/unemployment additionally led to the intensification of job search strategies and of the household/caregiving workload which also negatively impacted health. Health problems, in turn, contributed to pushing participants into long-term substandard employment trajectories. Participants' experiences were heavily structured by their social location as low income racialized immigrant women. Our study provides needed qualitative evidence on the gendered and racialized dimensions of under/unemployment, and adverse health impacts resulting from this. Drawing on intersectional analysis, we unpack the role that social location plays in creating highly uneven patterns of under/unemployment and negative health pathways for racialized immigrant women. We discuss equity informed strategies to help racialized immigrant women overcome barriers to stable work that match their education and/or experience.

Impact of model structure on flow simulation and hydrological realism: from a lumped to a semi-distributed approach

NASA Astrophysics Data System (ADS)

Garavaglia, Federico; Le Lay, Matthieu; Gottardi, Fréderic; Garçon, Rémy; Gailhard, Joël; Paquet, Emmanuel; Mathevet, Thibault

2017-08-01

Model intercomparison experiments are widely used to investigate and improve hydrological model performance. However, a study based only on runoff simulation is not sufficient to discriminate between different model structures. Hence, there is a need to improve hydrological models for specific streamflow signatures (e.g., low and high flow) and multi-variable predictions (e.g., soil moisture, snow and groundwater). This study assesses the impact of model structure on flow simulation and hydrological realism using three versions of a hydrological model called MORDOR: the historical lumped structure and a revisited formulation available in both lumped and semi-distributed structures. In particular, the main goal of this paper is to investigate the relative impact of model equations and spatial discretization on flow simulation, snowpack representation and evapotranspiration estimation. Comparison of the models is based on an extensive dataset composed of 50 catchments located in French mountainous regions. The evaluation framework is founded on a multi-criterion split-sample strategy. All models were calibrated using an automatic optimization method based on an efficient genetic algorithm. The evaluation framework is enriched by the assessment of snow and evapotranspiration modeling against in situ and satellite data. The results showed that the new model formulations perform significantly better than the initial one in terms of the various streamflow signatures, snow and evapotranspiration predictions. The semi-distributed approach provides better calibration-validation performance for the snow cover area, snow water equivalent and runoff simulation, especially for nival catchments.

Dating Kaali Crater (Estonia) based on charcoal emplaced within proximal ejecta blanket

NASA Astrophysics Data System (ADS)

Losiak, Anna; Wild, Eva Maria; Huber, Matthew S.; Wisniowski, Tomasz; Paavel, Kristiina; Jõeleht, Argo; Välja, Rudolf; Plado, Jüri; Kriiska, Aivar; Wilk, Jakob; Zanetti, Michael; Geppert, Wolf D.; Kulkov, Alexander; Steier, Peter; Pirkovic, Irena

2015-04-01

The Kaali impact field consists of nine identified craters located on the Saaremaa Island in Estonia. The largest crater is 110 m in diameter (centered around 58°22'21.94"N, 22°40'09.91" E). It was formed by impact of an IAB iron meteoroid into Silurian dolomite target rocks covered by up to a few meters of glacial till (Veski et al. 2007). The age of the Kaali impact structure is still a matter of debate, and the estimates provided by different authors vary considerably between ~6400 BC (Raukas et al. 1995, Moora et al. 2012) and ~400 BC (Rasmussen et al. 2000, Veski et al. 2001). These ages were derived by 14C dating of marker horizons, characterized by a slightly elevated iridium content within the nearby Piila bog yielding a calibrated age of 800-400 BC (Rasmussen et al. 2000, Veski et al. 2001) and occurrences of glassy siliceous material in the Piila bog (~6400 BC: Raukas et al. 1995) or iron microspherules in an organic-rich layer of the Reo gravel pit (6400 BC: Moora et al. 2012). However, the source of the foreign material within those layers was never unequivocally connected with the Kaali crater. 14C dating of material from post-impact organic sediments within Kaali impact craters yielded ages between 1800-1500 BC (Saarse et al. 1991, Veski et al. 2004) and 1450-400 BC (Aaloe et al. 1963). These dates underestimate the age of impact as organic sediments within the crater started to form at unknown period after the impact. On the other hand, Veski et al. (2004) suggested a reservoir effect that might have caused artificially "aging" of the organic matter because the crater was emplaced within Silurian dolomite which is rich in old carbon. The aim of this study is to determine the age of the Kaali crater by 14C dating of organic material covered by the continuous layer of proximal ejecta. This research was conducted in conjunction with a new structural investigation of Kaali Main (Zanetti et al. 2015). Ten samples collected from different locations within the trench (located ~12 meters to the SW from the rim crest of the main crater) and at different depths in respect to the ejecta-till boundary were processed separately. 14C dating was per-formed at the Vienna Environmental Research Accelerator at the University of Vienna (Austria). The calibrated (95,4% probability) time ranges of eight out of ten samples span the time interval from ~1650 BC to ~1400 BC. This age is based on dating charcoal within the ejecta blanket which makes it directly linked with the impact structure, and not susceptible to potential reservoir effects. References: Aaloe et al. 1963. Eesti Loodus 6:262-265. Moora et al. 2012. Geochronometria 39: 262-267. Raukas et al. 1995. Proc. Estonian Acad. Sci., Geology 44:177-183. Rasmussen et al. 2000. MAPS 35:1067-1071. Saarse et al. 1991. Bull. Geol. Soc. Finland 63:129-139. Veski et al. 2007. Comet/Asteroid Impacts and Hu-man Society:265-275. Veski et al. 2001. MAPS 36:1367-1376. Veski et al. 2004. Veg Hist Archaeobot 13:197-206. Zanetti et al. 2015. 46th LPSC.

A Holistic Look at Minimizing Adverse Environmental Impact Under Section 316(b) of the Clean Water Act

DOE PAGES

Veil, John A.; Puder, Markus G.; Littleton, Debra J.; ...

2002-01-01

Section 316(b) of the Clean Water Act (CWA) requires that “the location, design, construction, and capacity of cooling water intake structures reflect the best technology available for minimizing adverse environmental impact.” As the U.S. Environmental Protection Agency (EPA) develops new regulations to implement Section 316(b), much of the debate has centered on adverse impingement and entrainment impacts of cooling-water intake structures. Depending on the specific location and intake layout, once-through cooling systems withdrawing many millions of gallons of water per day can, to a varying degree, harm fish and other aquatic organisms in the water bodies from which the coolingmore » water is withdrawn. Therefore, opponents of once-through cooling systems have encouraged the EPA to require wet or dry cooling tower systems as the best technology available (BTA), without considering site-specific conditions. However, within the context of the broader scope of the CWA mandate, this focus seems too narrow. Therefore, this article examines the phrase “minimizing adverse environmental impact” in a holistic light. Emphasis is placed on the analysis of the terms “environmental” and “minimizing.” Congress chose “environmental” in lieu of other more narrowly focused terms like “impingement and entrainment,” “water quality,” or “aquatic life.” In this light, BTA for cooling-water intake structures must minimize the entire suite of environmental impacts, as opposed to just those associated with impingement and entrainment. Wet and dry cooling tower systems work well to minimize entrainment and impingement, but they introduce other equally important impacts because they impose an energy penalty on the power output of the generating unit. The energy penalty results from a reduction in plant operating efficiency and an increase in internal power consumption. As a consequence of the energy penalty, power companies must generate additional electricity to achieve the same net output. This added production leads to additional environmental impacts associated with extraction and processing of the fuel, air emissions from burning the fuel, and additional evaporation of freshwater supplies during the cooling process. Wet towers also require the use of toxic biocides that are subsequently discharged or disposed. The other term under consideration, “minimizing,” does not equal “eliminating.” Technologies may be available to minimize but not totally eliminate adverse environmental impacts.« less

78 FR 78948 - Intent To Prepare a Supplemental Environmental Impact Statement for the Route 460 Location Study...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-27

... Environmental Impact Statement for the Route 460 Location Study From Prince George County to the City of Suffolk... Route 460 Location Study Final Environmental Impact Statement (FEIS). The purpose of this SEIS is to... roads. The Applicant has entered into a design-build contract with VDOT to design and construct the...

Soil Structure - A Neglected Component of Land-Surface Models

NASA Astrophysics Data System (ADS)

Fatichi, S.; Or, D.; Walko, R. L.; Vereecken, H.; Kollet, S. J.; Young, M.; Ghezzehei, T. A.; Hengl, T.; Agam, N.; Avissar, R.

2017-12-01

Soil structure is largely absent in most standard sampling and measurements and in the subsequent parameterization of soil hydraulic properties deduced from soil maps and used in Earth System Models. The apparent omission propagates into the pedotransfer functions that deduce parameters of soil hydraulic properties primarily from soil textural information. Such simple parameterization is an essential ingredient in the practical application of any land surface model. Despite the critical role of soil structure (biopores formed by decaying roots, aggregates, etc.) in defining soil hydraulic functions, only a few studies have attempted to incorporate soil structure into models. They mostly looked at the effects on preferential flow and solute transport pathways at the soil profile scale; yet, the role of soil structure in mediating large-scale fluxes remains understudied. Here, we focus on rectifying this gap and demonstrating potential impacts on surface and subsurface fluxes and system wide eco-hydrologic responses. The study proposes a systematic way for correcting the soil water retention and hydraulic conductivity functions—accounting for soil-structure—with major implications for near saturated hydraulic conductivity. Modification to the basic soil hydraulic parameterization is assumed as a function of biological activity summarized by Gross Primary Production. A land-surface model with dynamic vegetation is used to carry out numerical simulations with and without the role of soil-structure for 20 locations characterized by different climates and biomes across the globe. Including soil structure affects considerably the partition between infiltration and runoff and consequently leakage at the base of the soil profile (recharge). In several locations characterized by wet climates, a few hundreds of mm per year of surface runoff become deep-recharge accounting for soil-structure. Changes in energy fluxes, total evapotranspiration and vegetation productivity are less significant but they can reach up to 10% in specific locations. Significance for land-surface and hydrological modeling and implications for distributed domains are discussed.

Structural Health Management of Damaged Aircraft Structures Using the Digital Twin Concept

NASA Technical Reports Server (NTRS)

Seshadri, Banavara R.; Krishnamurthy, Thiagarajan

2017-01-01

The development of multidisciplinary integrated Structural Health Management (SHM) tools will enable accurate detection, and prognosis of damaged aircraft under normal and adverse conditions during flight. As part of the digital twin concept, methodologies are developed by using integrated multiphysics models, sensor information and input data from an in-service vehicle to mirror and predict the life of its corresponding physical twin. SHM tools are necessary for both damage diagnostics and prognostics for continued safe operation of damaged aircraft structures. The adverse conditions include loss of control caused by environmental factors, actuator and sensor faults or failures, and structural damage conditions. A major concern in these structures is the growth of undetected damage/cracks due to fatigue and low velocity foreign object impact that can reach a critical size during flight, resulting in loss of control of the aircraft. To avoid unstable, catastrophic propagation of damage during a flight, load levels must be maintained that are below a reduced load-carrying capacity for continued safe operation of an aircraft. Hence, a capability is needed for accurate real-time predictions of damage size and safe load carrying capacity for structures with complex damage configurations. In the present work, a procedure is developed that uses guided wave responses to interrogate damage. As the guided wave interacts with damage, the signal attenuates in some directions and reflects in others. This results in a difference in signal magnitude as well as phase shifts between signal responses for damaged and undamaged structures. Accurate estimation of damage size, location, and orientation is made by evaluating the cumulative signal responses at various pre-selected sensor locations using a genetic algorithm (GA) based optimization procedure. The damage size, location, and orientation is obtained by minimizing the difference between the reference responses and the responses obtained by wave propagation finite element analysis of different representative cracks, geometries, and sizes.

Paleomagnetism and petrophysics of the Jänisjärvi impact structure, Russian Karelia

NASA Astrophysics Data System (ADS)

Salminen, J.; Donadini, F.; Pesonen, L. J.; Masaitis, V. L.; Naumov, M. V.

Paleomagnetic, rock magnetic, and petrophysical results are presented for impactites and target rocks from the Lake Jänisjärvi impact structure, Russian Karelia. The impactites (tagamites, suevites, and lithic breccias) are characterized by increased porosity and magnetization, which is in agreement with observations performed at other impact structures. Thermomagnetic, hysteresis, and scanning electron microscope (SEM) analysis document the presence of primary multidomain titanomagnetite with additional secondary titanomaghemite and ilmenohematite. The characteristic impact-related remanent magnetization (ChRM) direction (D = 101.5°, I = 73.1°, α95 = 6.2°) yields a pole (Lat. = 45.0°N, Long. = 76.9°E, dp = 9.9°, dm = 11.0°). Additionally, the same component is observed as an overprint on some rocks located in the vicinity of the structure, which provides proofs of its primary origin.An attempt was made to determine the ancient geomagnetic field intensity. Seven reliable results were obtained, yielding an ancient intensity of 68.7 ± 7.6 μT (corresponding to VDM of 10.3 ± 1.1 × 1022 Am2). The intensity, however, appears to be biased toward high values mainly because of the concave shape of the Arai diagrams.The new paleomagnetic data and published isotopic ages for the structure are in disagreement. According to well-defined paleomagnetic data, two possible ages for magnetization of Jänisjärvi rocks exist: 1) Late Sveconorwegian age (900-850 Myr) or 2) Late Cambrian age (˜500 Myr). However, published isotopic ages are 718 ± 5 Myr (K-Ar) and 698 ± 22 Myr (39Ar-40Ar), but such isotopic dating methods are often ambiguous for the impactites.

High-resolution seismic-reflection images across the ICDP-USGS Eyreville deep drilling site, Chesapeake Bay impact structure

USGS Publications Warehouse

Powars, D.S.; Catchings, R.D.; Goldman, M.R.; Gohn, G.S.; Horton, J. Wright; Edwards, L.E.; Rymer, M.J.; Gandhok, G.

2009-01-01

The U.S. Geological Survey (USGS) acquired two 1.4-km-long, high-resolution (??5 m vertical resolution) seismic-reflection lines in 2006 that cross near the International Continental Scientifi c Drilling Program (ICDP)-USGS Eyreville deep drilling site located above the late Eocene Chesapeake Bay impact structure in Virginia, USA. Five-meter spacing of seismic sources and geophones produced high-resolution images of the subsurface adjacent to the 1766-m-depth Eyreville core holes. Analysis of these lines, in the context of the core hole stratigraphy, shows that moderateamplitude, discontinuous, dipping reflections below ??527 m correlate with a variety of Chesapeake Bay impact structure sediment and rock breccias recovered in the cores. High-amplitude, continuous, subhorizontal reflections above ??527 m depth correlate with the uppermost part of the Chesapeake Bay impact structure crater-fi ll sediments and postimpact Eocene to Pleistocene sediments. Refl ections with ??20-30 m of relief in the uppermost part of the crater-fi ll and lowermost part of the postimpact section suggest differential compaction of the crater-fi ll materials during early postimpact time. The top of the crater-fi ll section also shows ??20 m of relief that appears to represent an original synimpact surface. Truncation surfaces, locally dipping reflections, and depth variations in reflection amplitudes generally correlate with the lithostratigraphic and sequence-stratigraphic units and contacts in the core. Seismic images show apparent postimpact paleochannels that include the fi rst possible Miocene paleochannels in the Mid-Atlantic Coastal Plain. Broad downwarping in the postimpact section unrelated to structures in the crater fi ll indicates postimpact sediment compaction. ?? 2009 The Geological Society of America.

Safety assessment characteristics of pedestrian legform impactors in vehicle-front impact tests.

PubMed

Matsui, Yasuhiro

2014-12-01

This study investigated the characteristics of safety assessment results of front-area vehicle impact tests carried out using the Transport Research Laboratory (TRL) legform impactor and a flexible legform impactor (FLEX legform impactor). Different types of vehicles (sedan, sport utility vehicle, high-roof K-car, and light cargo van) were examined. The impact locations in the study were the center of the bumper and an extremely stiff structure of the bumper (i.e., in front of the side member) of each tested vehicle. The measured injury criteria were normalized by injury assessment reference values of each legform impactor. The test results for center and side-member impacts indicated that there were no significant differences in ligament injury assessments derived from the normalized knee ligament injury measures between the TRL legform impactor and the FLEX legform impactor. Evaluations made using the TRL legform impactor and the FLEX legform impactor are thus similar in the vehicle safety investigation for knee ligament injury. Vehicle-center impact test results revealed that the tibia fracture assessments derived from the normalized tibia fracture measures did not significantly differ between the TRL legform impactor and the FLEX legform impactor. However, for an impact against an extremely stiff structure, there was a difference in the tibia fracture assessment between the FLEX legform impactor and the TRL legform impactor owing to their different sensor types. Copyright © 2014 Elsevier Ltd. All rights reserved.

Waves Generated by Asteroid Impacts and Their Hazard Consequences on The Shorelines

NASA Astrophysics Data System (ADS)

Ezzedine, S. M.; Miller, P. L.; Dearborn, D. S.

2014-12-01

We have performed numerical simulations of a hypothetical asteroid impact onto the ocean in support of an emergency preparedness, planning, and management exercise. We addressed the scenario from asteroid entry; to ocean impact (splash rim); to wave generation, propagation, and interaction with the shoreline. For the analysis we used GEODYN, a hydrocode, to simulate the impact and generate the source wave for the large-scale shallow water wave program, SWWP. Using state-of-the-art, high-performance computing codes we simulated three impact areas — two are located on the West Coast near Los Angeles's shoreline and the San Francisco Bay, respectively, and the third is located in the Gulf of Mexico, with a possible impact location between Texas and Florida. On account of uncertainty in the exact impact location within the asteroid risk corridor, we examined multiple possibilities for impact points within each area. Uncertainty in the asteroid impact location was then convolved and represented as uncertainty in the shoreline flooding zones. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344, and partially funded by the Laboratory Directed Research and Development Program at LLNL under tracking code 12-ERD-005.

Deep drilling in the Chesapeake Bay impact structure - An overview

USGS Publications Warehouse

Gohn, G.S.; Koeberl, C.; Miller, K.G.; Reimold, W.U.

2009-01-01

The late Eocene Chesapeake Bay impact structure lies buried at moderate depths below Chesapeake Bay and surrounding landmasses in southeastern Virginia, USA. Numerous characteristics made this impact structure an inviting target for scientific drilling, including the location of the impact on the Eocene continental shelf, its threelayer target structure, its large size (??85 km diameter), its status as the source of the North American tektite strewn field, its temporal association with other late Eocene terrestrial impacts, its documented effects on the regional groundwater system, and its previously unstudied effects on the deep microbial biosphere. The Chesapeake Bay Impact Structure Deep Drilling Project was designed to drill a deep, continuously cored test hole into the central part of the structure. A project workshop, funding proposals, and the acceptance of those proposals occurred during 2003-2005. Initial drilling funds were provided by the International Continental Scientific Drilling Program (ICDP) and the U.S. Geological Survey (USGS). Supplementary funds were provided by the National Aeronautics and Space Administration (NASA) Science Mission Directorate, ICDP, and USGS. Field operations were conducted at Eyreville Farm, Northampton County, Virginia, by Drilling, Observation, and Sampling of the Earth's Continental Crust (DOSECC) and the project staff during September-December 2005, resulting in two continuously cored, deep holes. The USGS and Rutgers University cored a shallow hole to 140 m in April-May 2006 to complete the recovered section from land surface to 1766 m depth. The recovered section consists of 1322 m of crater materials and 444 m of overlying postimpact Eocene to Pleistocene sediments. The crater section consists of, from base to top: basement-derived blocks of crystalline rocks (215 m); a section of suevite, impact melt rock, lithic impact breccia, and cataclasites (154 m); a thin interval of quartz sand and lithic blocks (26 m); a granite megablock (275 m); and sediment blocks and boulders, polymict, sediment-clast-dominated sedimentary breccias, and a thin upper section of stratified sediments (652 m). The cored postimpact sediments provide insight into the effects of a large continental-margin impact on subsequent coastal-plain sedimentation. This volume contains the first results of multidisciplinary studies of the Eyreville cores and related topics. The volume is divided into these sections: geologic column; borehole geophysical studies; regional geophysical studies; crystalline rocks, impactites, and impact models; sedimentary breccias; postimpact sediments; hydrologic and geothermal studies; and microbiologic studies. ?? 2009 The Geological Society of America.

Structural acoustic control of plates with variable boundary conditions: design methodology.

PubMed

Sprofera, Joseph D; Cabell, Randolph H; Gibbs, Gary P; Clark, Robert L

2007-07-01

A method for optimizing a structural acoustic control system subject to variations in plate boundary conditions is provided. The assumed modes method is used to build a plate model with varying levels of rotational boundary stiffness to simulate the dynamics of a plate with uncertain edge conditions. A transducer placement scoring process, involving Hankel singular values, is combined with a genetic optimization routine to find spatial locations robust to boundary condition variation. Predicted frequency response characteristics are examined, and theoretically optimized results are discussed in relation to the range of boundary conditions investigated. Modeled results indicate that it is possible to minimize the impact of uncertain boundary conditions in active structural acoustic control by optimizing the placement of transducers with respect to those uncertainties.

New Data Products and Tools from STEREO's IMPACT Investigation

NASA Astrophysics Data System (ADS)

Schroeder, P. C.; Luhmann, J. G.; Li, Y.; Huttunen, E.; Toy, V.; Russell, C. T.; Davis, A.

2008-05-01

STEREO's IMPACT (In-situ Measurements of Particles and CME Transients) investigation provides the first opportunity for long duration, detailed observations of 1 AU magnetic field structures, plasma and suprathermal electrons, and energetic particles at points bracketing Earth's heliospheric location. The IMPACT team has developed both human-friendly web portals and API's (application program interfaces) which provide straight- foward data access to scientists and the Virtual Observatories. Several new data products and web features have been developed including the release of more and higher-level data products, a library of TPLOT-based IDL data analysis routines, and web sites devoted to event analysis and inter-mission and inter-disciplinary collaboration. A web browser integrating STEREO and L1 in situ data with imaging and models provides a powerful venue for exploring the Sun-Earth connection. These latest releases enable the larger scientific community to use STEREO's unique in-situ data in novel ways along side "third eye" data sets from Wind, ACE and other heliospheric missions contributing to a better understanding of three dimensional structures in the solar wind.

Structural patterns of the human ABCC4/MRP4 exporter in lipid bilayers rationalize clinically observed polymorphisms.

PubMed

Chantemargue, B; Di Meo, F; Berka, K; Picard, N; Arnion, H; Essig, M; Marquet, P; Otyepka, M; Trouillas, P

2018-03-10

The ABCC4/MRP4 exporter has a clinical impact on membrane transport of a broad range of xenobiotics. It is expressed at key locations for drug disposition or effects such as in the liver, the kidney and blood cells. Several polymorphisms and mutations (e.g., p.Gly187Trp) leading to MRP4 dysfunction are associated with an increased risk of toxicity of some drugs. So far, no human MRP4 structure has been elucidated, precluding rationalization of these dysfunctions at a molecular level. We constructed an atomistic model of the wild type (WT) MRP4 and the p.Gly187Trp mutant embedded in different lipid bilayers and relaxed them for hundreds of nanoseconds by molecular dynamics simulations. The WT MRP4 molecular structure confirmed and ameliorated the general knowledge about the transmembrane helices and the two nucleotide binding domains. Moreover, our model elucidated positions of three generally unresolved domains: L 1 (linker between the two halves of the exporter); L 0 (N-terminal domain); and the zipper helices (between the two NBDs). Each domain was thoroughly described in view of its function. The p.Gly187Trp mutation induced a huge structural impact on MRP4, mainly affecting NBD 1 structure and flexibility. The structure of transporter enabled rationalization of known dysfunctions associated with polymorphism of MRP4. This model is available to the pharmacology community to decipher the impact of any other clinically observed polymorphism and mutation on drug transport, giving rise to in silico predictive pharmacogenetics. Copyright © 2018 Elsevier Ltd. All rights reserved.

Numerical Simulation of Blast Action on Civil Structures in Urban Environment

NASA Astrophysics Data System (ADS)

Valger, Svetlana A.; Fedorova, Natalya N.; Fedorov, Alexander V.

2017-10-01

Nowadays, a lot of industrial accidents accompanied by explosions are happening throughout the world. Also, increase in the number of terrorist acts committed by means of explosions is observed. For improving safety of buildings and structures it is necessary to raise their resistance to explosive effects, as well as to be able to predict degree of potential damage upon explosive loads of various intensities. One of the principal goals in designing the structure resistant to explosive effects is to determine the dynamic response of structures to the impact of the blast wave. To this end, the transient pressure loads on the walls of the civil engineering structures are to be determined. The simulation of explosion is highly complicated, involving an explosion causing the shock wave propagation in air and then interaction with a structure. The engineering-level techniques permit one to estimate an explosive shock impact only for isolated buildings. The complexity of the building, the presence of nearby structures and the surrounding environment cannot be taken into account. Advanced computer aid engineering (CAE) software techniques combined with the latest methods of discrete three-dimensional city modelling permits one to simulate and analyse the effects of explosions in urban areas with a precision which previously was not possible. In the paper, the simulation results are presented of shock wave forming due to a spherical explosive charge and its propagation in the vicinity of geometrical configuration imitating an urban environment. The numerical simulation of a flow in the vicinity of prisms of different cross-sections and heights located on a flat plate was performed. The calculations are carried out in a three-dimensional non-viscous formulation using ANSYS software. On a basis of simulation results, a complex wave structures were analysed, and all the peculiarities of flows and pressure history records on building walls were described and explained. The possibility of a correct description of the non-stationary wave flow in the vicinity of the complex of obstacles is demonstrated. The results are compared with the experimental data on the pressure distribution in gauges located on the prism walls. The estimation of shock wave exposure intensity was performed to different objects.

Effects of voxelization on dose volume histogram accuracy

NASA Astrophysics Data System (ADS)

Sunderland, Kyle; Pinter, Csaba; Lasso, Andras; Fichtinger, Gabor

2016-03-01

PURPOSE: In radiotherapy treatment planning systems, structures of interest such as targets and organs at risk are stored as 2D contours on evenly spaced planes. In order to be used in various algorithms, contours must be converted into binary labelmap volumes using voxelization. The voxelization process results in lost information, which has little effect on the volume of large structures, but has significant impact on small structures, which contain few voxels. Volume differences for segmented structures affects metrics such as dose volume histograms (DVH), which are used for treatment planning. Our goal is to evaluate the impact of voxelization on segmented structures, as well as how factors like voxel size affects metrics, such as DVH. METHODS: We create a series of implicit functions, which represent simulated structures. These structures are sampled at varying resolutions, and compared to labelmaps with high sub-millimeter resolutions. We generate DVH and evaluate voxelization error for the same structures at different resolutions by calculating the agreement acceptance percentage between the DVH. RESULTS: We implemented tools for analysis as modules in the SlicerRT toolkit based on the 3D Slicer platform. We found that there were large DVH variation from the baseline for small structures or for structures located in regions with a high dose gradient, potentially leading to the creation of suboptimal treatment plans. CONCLUSION: This work demonstrates that labelmap and dose volume voxel size is an important factor in DVH accuracy, which must be accounted for in order to ensure the development of accurate treatment plans.

Evolution of groundwater chemistry along fault structures in sandstone

NASA Astrophysics Data System (ADS)

Dausse, A.; Guiheneuf, N.; Pierce, A. A.; Cherry, J. A.; Parker, B. L.

2016-12-01

Fluid-rock interaction across geological structures plays a major role on evolution of groundwater chemistry and physical properties of reservoirs. In particular, groundwater chemistry evolve on different facies according to residence times which can be linked to hydraulic properties of the geological unit. In this study, we analyze groundwater samples collected at an 11 km² site located in southern California (USA) to evaluate the evolution of groundwater chemistry according to different geological structures. Major and minor elements were sampled at the same period of time from 40 wells located along the main structures in the northeast of the site, where major NE-SW trending faults and other oriented ESE-WNW are present in sandstone Chatsworth formation. By analyzing the spatial distribution of ions concentration at the site scale, several hydrochemical compartments (main- and sub-compartments) can be distinguished and are in agreement with structural and hydrological information. In particular, as previously observed from piezometric informations, the shear zone fault serves as a barrier for groundwater flow and separates the site on two mains compartments. In addition, the analysis along major faults oriented orthogonal to this shear zone (ESE-WNW) in the eastern part of the site, shows an increase in mineralization following the hydraulic gradient. This salinization has been confirmed by ionic ratio and Gibbs plots and is attributed to fluid-rock interaction processes. In particular, groundwater chemistry seems to evolve from bicarbonate to sodium facies. Moreover, the gradient of concentrations vary depending on fault locations and can be related to their hydraulic properties and hence to different characteristic times from point to point. To conclude, major faults across the site display different degrees of groundwater chemistry evolution, linked to their physical properties, which may in turn have a large impact on contaminant transport and attenuation.

75 FR 17161 - Job Corps: Preliminary Finding of No Significant Impact (FONSI) for the Installation of a Small...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

... Impact (FONSI) for the Installation of a Small Wind Turbine at the Pine Ridge Job Corps Center Located at...: Preliminary Finding of No Significant Impact (FONSI) for a small Wind Turbine Installation to be located at... prepared for a proposed Wind Turbine Installation to be located at the Pine Ridge Job Corps Center, 15710...

Structure of 311 service requests as a signature of urban location

PubMed Central

Wang, Lingjing; Qian, Cheng; Kats, Philipp; Kontokosta, Constantine; Sobolevsky, Stanislav

2017-01-01

While urban systems demonstrate high spatial heterogeneity, many urban planning, economic and political decisions heavily rely on a deep understanding of local neighborhood contexts. We show that the structure of 311 Service Requests enables one possible way of building a unique signature of the local urban context, thus being able to serve as a low-cost decision support tool for urban stakeholders. Considering examples of New York City, Boston and Chicago, we demonstrate how 311 Service Requests recorded and categorized by type in each neighborhood can be utilized to generate a meaningful classification of locations across the city, based on distinctive socioeconomic profiles. Moreover, the 311-based classification of urban neighborhoods can present sufficient information to model various socioeconomic features. Finally, we show that these characteristics are capable of predicting future trends in comparative local real estate prices. We demonstrate 311 Service Requests data can be used to monitor and predict socioeconomic performance of urban neighborhoods, allowing urban stakeholders to quantify the impacts of their interventions. PMID:29040314

Structure of 311 service requests as a signature of urban location.

PubMed

Wang, Lingjing; Qian, Cheng; Kats, Philipp; Kontokosta, Constantine; Sobolevsky, Stanislav

2017-01-01

While urban systems demonstrate high spatial heterogeneity, many urban planning, economic and political decisions heavily rely on a deep understanding of local neighborhood contexts. We show that the structure of 311 Service Requests enables one possible way of building a unique signature of the local urban context, thus being able to serve as a low-cost decision support tool for urban stakeholders. Considering examples of New York City, Boston and Chicago, we demonstrate how 311 Service Requests recorded and categorized by type in each neighborhood can be utilized to generate a meaningful classification of locations across the city, based on distinctive socioeconomic profiles. Moreover, the 311-based classification of urban neighborhoods can present sufficient information to model various socioeconomic features. Finally, we show that these characteristics are capable of predicting future trends in comparative local real estate prices. We demonstrate 311 Service Requests data can be used to monitor and predict socioeconomic performance of urban neighborhoods, allowing urban stakeholders to quantify the impacts of their interventions.

The Lawn Hill annulus: An Ordovician meteorite impact into water-saturated dolomite

NASA Astrophysics Data System (ADS)

Darlington, Vicki; Blenkinsop, Tom; Dirks, Paul; Salisbury, Jess; Tomkins, Andrew

2016-12-01

The Lawn Hill Impact Structure (LHIS) is located 250 km N of Mt Isa in NW Queensland, Australia, and is marked by a highly deformed dolomite annulus with an outer diameter of 18 km, overlying low metamorphic grade siltstone, sandstone, and shale, along the NE margin of the Georgina Basin. This study provides detailed field observations from sections of the Lawn Hill annulus and adjacent areas that demonstrate a clear link between the deformation of the dolomite and the Lawn Hill impact. 40Ar-39Ar dating of impact-related melt particles provides a time of impact in the Ordovician (472 ± 8 Ma) when the Georgina Basin was an active depocenter. The timing and stratigraphic thickness of the dolomite sequence in the annulus suggest that there was possibly up to 300 m of additional sedimentary rocks on top of the currently exposed Thorntonia Limestone at the time of impact. The exposed annulus is remarkably well preserved, with preservation attributed to postimpact sedimentation. The LHIS has an atypical crater morphology with no central uplift. The heterogeneous target materials at Lawn Hill were probably low-strength, porous, and water-saturated, with all three properties affecting the crater morphology. The water-saturated nature of the carbonate unit at the time of impact is thought to have influenced the highly brecciated nature of the annulus, and restricted melt production. The impact timing raises the possibility that the Lawn Hill structure may be a member of a group of impacts resulting from an asteroid breakup that occurred in the mid-Ordovician (470 ± 6 Ma).

Stepwise introduction of laparoscopic liver surgery: validation of guideline recommendations.

PubMed

van der Poel, Marcel J; Huisman, Floor; Busch, Olivier R; Abu Hilal, Mohammad; van Gulik, Thomas M; Tanis, Pieter J; Besselink, Marc G

2017-10-01

Uncontrolled introduction of laparoscopic liver surgery (LLS) could compromise postoperative outcomes. A stepwise introduction of LLS combined with structured training is advised. This study aimed to evaluate the impact of such a stepwise introduction. A retrospective, single-center case series assessing short term outcomes of all consecutive LLS in the period November 2006-January 2017. The technique was implemented in a stepwise fashion. To evaluate the impact of this stepwise approach combined with structured training, outcomes of LLS before and after a laparoscopic HPB fellowship were compared. A total of 135 laparoscopic resections were performed. Overall conversion rate was 4% (n = 5), clinically relevant complication rate 13% (n = 18) and mortality 0.7% (n = 1). A significant increase in patients with major LLS, multiple liver resections, previous abdominal surgery, malignancies and lesions located in posterior segments was observed after the fellowship as well as a decrease in the use of hand-assistance. Increasing complexity in the post fellowship period was reflected by an increase in operating times, but without comprising other surgical outcomes. A stepwise introduction of LLS combined with structured training reduced the clinical impact of the learning curve, thereby confirming guideline recommendations. Copyright © 2017 International Hepato-Pancreato-Biliary Association Inc. Published by Elsevier Ltd. All rights reserved.

Strontium and neodymium isotope systematics of target rocks and impactites from the El'gygytgyn impact structure: Linking impactites and target rocks

NASA Astrophysics Data System (ADS)

Wegner, Wencke; Koeberl, Christian

2016-12-01

The 3.6 Ma El'gygytgyn structure, located in northeastern Russia on the Chukotka Peninsula, is an 18 km diameter complex impact structure. The bedrock is formed by mostly high-silica volcanic rocks of the 87 Ma old Okhotsk-Chukotka Volcanic Belt (OCVB). Volcanic target rocks and impact glasses collected on the surface, as well as drill core samples of bedrock and impact breccias have been investigated by thermal ionization mass spectrometry (TIMS) to obtain new insights into the relationships between these lithologies in terms of Nd and Sr isotope systematics. Major and trace element data for impact glasses are added to compare with the composition of target rocks and drill core samples. Sr isotope data are useful tracers of alteration processes and Nd isotopes reveal characteristics of the magmatic sources of the target rocks, impact breccias, and impact glasses. There are three types of target rocks mapped on the surface: mafic volcanics, dacitic tuff and lava of the Koekvun' Formation, and dacitic to rhyolitic ignimbrite of the Pykarvaam Formation. The latter represents the main contributor to the impact rocks. The drill core is divided into a suevite and a bedrock section by the Sr isotope data, for which different postimpact alteration regimes have been detected. Impact glasses from the present-day surface did not suffer postimpact hydrothermal alteration and their data indicate a coherent alteration trend in terms of Sr isotopes with the target rocks from the surface. Surprisingly, the target rocks do not show isotopic coherence with the Central Chukotka segment of the OCVB or with the Berlozhya magmatic assemblage (BMA), a late Jurassic felsic volcanic suite that crops out in the eastern part of the central Chukotka segment of the OCVB. However, concordance for these rocks exists with the Okhotsk segment of the OCVB. This finding argues for variable source magmas having contributed to the build-up of the OCVB.

Location, Location, Location: How Would a High-Performing Charter School Network Fare in Different States?

ERIC Educational Resources Information Center

Lozier, Chris; Rotherham, Andrew J.

2011-01-01

In this paper the authors do not examine different operating strategies for charter schools or analyze the impact of their often educationally intensive models on finance. Instead, because public charter schools are funded predominantly by public dollars, they simply ask what impact location--and its associated variances in public funding and the…

Impact of small-scale vegetation structure on tephra layer preservation

PubMed Central

Cutler, Nick A.; Shears, Olivia M.; Streeter, Richard T.; Dugmore, Andrew J.

2016-01-01

The factors that influence tephra layer taphonomy are poorly understood, but vegetation cover is likely to play a role in the preservation of terrestrial tephra deposits. The impact of vegetation on tephra layer preservation is important because: 1) the morphology of tephra layers could record key characteristics of past land surfaces and 2) vegetation-driven variability in tephra thickness could affect attempts to infer eruption and dispersion parameters. We investigated small- (metre-) scale interactions between vegetation and a thin (<10 cm), recent tephra layer. We conducted surveys of vegetation structure and tephra thickness at two locations which received a similar tephra deposit, but had contrasting vegetation cover (moss vs shrub). The tephra layer was thicker and less variable under shrub cover. Vegetation structure and layer thickness were correlated on the moss site but not under shrub cover, where the canopy reduced the influence of understory vegetation on layer morphology. Our results show that vegetation structure can influence tephra layer thickness on both small and medium (site) scales. These findings suggest that some tephra layers may carry a signal of past vegetation cover. They also have implications for the sampling effort required to reliably estimate the parameters of initial deposits. PMID:27845415

Earth Observations taken by Expedition 30 crewmember

NASA Image and Video Library

2011-11-26

ISS030-E-005456 (26 Nov. 2011) --- Emi Koussi Volcano and Aorounga Impact Crater, Chad are featured in this image photographed by an Expedition 30 crew member on the International Space Station. This striking photograph features two examples of circular landscape features?labeled as craters?that were produced by very different geological processes. At left, the broad grey-green shield volcano of Emi Koussi is visible. The volcano is marked by three overlapping calderas formed by eruptions; these form a large oblong depression at the 3,415 meter ASL summit of the volcano. A smaller crater sits within the larger caldera depression. While volcanic activity has not been observed, nor is mentioned in the historical record, an active thermal area is located on the southern flank. The circular Aorounga Impact Crater is located approximately 110 kilometers to the southeast of Emi Koussi and has its origin in forces from above rather than eruptions from below. According to scientists, the Aorounga structure is thought to record a meteor impact approximately 345-370 million years ago. The circular feature visible at upper right may be only one of three impact craters formed by the same event ? the other two are buried by sand deposits. The linear features (lower right) that arc around Emi Koussi and overprint Aorounga and the surrounding bedrock are known as yardangs; these are rock ridges formed by wind erosion.

Association of anatase (TiO2) and microbes: unusual fossilization effect or a potential biosignature?

USGS Publications Warehouse

Glamoclija, Mihaela; Andrew Steele,; Marc Fries,; Juergen Schieber,; Voytek, Mary A.; Charles S. Cockell,

2015-01-01

We combined microbial paleontology and molecular biology methods to study the Eyreville B drill core from the 35.3-Ma-old Chesapeake Bay impact structure,Virginia, USA. The investigated sample is a pyrite vein collected from the 1353.81-1353.89 m depth interval, located within a section of biotite granite. The granite is a pre-impact rock that was disrupted by the impact event. A search for inorganic (mineral) biosignatures revealed the presence of micron-size rod morphologies of anatase (TiO2) embedded in chlorite coatings on pyrite grains. Neither the Acridine Orange microbial probe nor deoxyribonucleic acid (DNA) extraction followed by polymerase chain reaction (PCR) amplifi cation showed the presence of DNA or ribonucleic acid (RNA) at the location of anatase rods, implying the absence of viable cells in the investigated area. A Nile Red microbial probe revealed the presence of lipids in the rods. Because most of the lipids are resistant over geologic time spans, they are good biomarkers, and they are an indicator of biogenicity for these possibly 35-Ma-old microbial fossils. The mineral assemblage suggests that rod morphologies are associated with low-temperature (<100 °C) hydrothermal alteration that involved aqueous fl uids. The temporal constraints on the anatase fossils are still uncertain because pre-impact alteration of the granite and postimpact heating may have provided identical conditions for anatase precipitation and microbial preservation.

The effect of ball impact location on racket and forearm joint angle changes for one-handed tennis backhand groundstrokes.

PubMed

King, Mark; Hau, Agnes; Blenkinsop, Glen

2017-07-01

Recreational tennis players tend to have higher incidence of tennis elbow, and this has been hypothesised to be related to one-handed backhand technique and off-centre ball impacts on the racket face. This study aimed to investigate for a range of participants the effect of off-longitudinal axis and off-lateral axis ball-racket impact locations on racket and forearm joint angle changes immediately following impact in one-handed tennis backhand groundstrokes. Three-dimensional racket and wrist angular kinematic data were recorded for 14 university tennis players each performing 30 "flat" one-handed backhand groundstrokes. Off-longitudinal axis ball-racket impact locations explained over 70% of the variation in racket rotation about the longitudinal axis and wrist flexion/extension angles during the 30 ms immediately following impact. Off-lateral axis ball-racket impact locations had a less clear cut influence on racket and forearm rotations. Specifically off-longitudinal impacts below the longitudinal axis forced the wrist into flexion for all participants with there being between 11° and 32° of forced wrist flexion for an off-longitudinal axis impact that was 1 ball diameter away from the midline. This study has confirmed that off-longitudinal impacts below the longitudinal axis contribute to forced wrist flexion and eccentric stretch of the wrist extensors and there can be large differences in the amount of forced wrist flexion from individual to individual and between strokes with different impact locations.

The Impact of Microphysics on Intensity and Structure of Hurricanes and Mesoscale Convective Systems

NASA Technical Reports Server (NTRS)

Tao, Wei-Kuo; Shi, Jainn J.; Jou, Ben Jong-Dao; Lee, Wen-Chau; Lin, Pay-Liam; Chang, Mei-Yu

2007-01-01

During the past decade, both research and operational numerical weather prediction models, e.g. Weather Research and Forecast (WRF) model, have started using more complex microphysical schemes originally developed for high-resolution cloud resolving models (CRMs) with a 1-2 km or less horizontal resolutions. WRF is a next-generation mesoscale forecast model and assimilation system that has incorporated modern software framework, advanced dynamics, numeric and data assimilation techniques, a multiple moveable nesting capability, and improved physical packages. WRF model can be used for a wide range of applications, from idealized research to operational forecasting, with an emphasis on horizontal grid sizes in the range of 1-10 km. The current WRF includes several different microphysics options such as Purdue Lin et al. (1983), WSM 6-class and Thompson microphysics schemes. We have recently implemented three sophisticated cloud microphysics schemes into WRF. The cloud microphysics schemes have been extensively tested and applied for different mesoscale systems in different geographical locations. The performances of these schemes have been compared to those from other WRF microphysics options. We are performing sensitivity tests in using WRF to examine the impact of six different cloud microphysical schemes on precipitation processes associated hurricanes and mesoscale convective systems developed at different geographic locations [Oklahoma (IHOP), Louisiana (Hurricane Katrina), Canada (C3VP - snow events), Washington (fire storm), India (Monsoon), Taiwan (TiMREX - terrain)]. We will determine the microphysical schemes for good simulated convective systems in these geographic locations. We are also performing the inline tracer calculation to comprehend the physical processes (i.e., boundary layer and each quadrant in the boundary layer) related to the development and structure of hurricanes and mesoscale convective systems.

Modeling economic implications of alternative treatment strategies for acute bacterial skin and skin structure infections.

PubMed

Revankar, Nikhil; Ward, Alexandra J; Pelligra, Christopher G; Kongnakorn, Thitima; Fan, Weihong; LaPensee, Kenneth T

2014-10-01

The economic implications from the US Medicare perspective of adopting alternative treatment strategies for acute bacterial skin and skin structure infections (ABSSSIs) are substantial. The objective of this study is to describe a modeling framework that explores the impact of decisions related to both the location of care and switching to different antibiotics at discharge. A discrete event simulation (DES) was developed to model the treatment pathway of each patient through various locations (emergency department [ED], inpatient, and outpatient) and the treatments prescribed (empiric antibiotic, switching to a different antibiotic at discharge, or a second antibiotic). Costs are reported in 2012 USD. The mean number of days on antibiotic in a cohort assigned to a full course of vancomycin was 11.2 days, with 64% of the treatment course being administered in the outpatient setting. Mean total costs per patient were $8671, with inpatient care accounting for 58% of the costs accrued. The majority of outpatient costs were associated with parenteral administration rather than drug acquisition or monitoring. Scenarios modifying the treatment pathway to increase the proportion of patients receiving the first dose in the ED, and then managing them in the outpatient setting or prescribing an oral antibiotic at discharge to avoid the cost associated with administering parenteral therapy, therefore have a major impact and lower the typical cost per patient by 11-20%. Since vancomycin is commonly used as empiric therapy in clinical practice, based on these analyses, a shift in treatment practice could result in substantial savings from the Medicare perspective. The choice of antibiotic and location of care influence the costs and resource use associated with the management of ABSSSIs. The DES framework presented here can provide insight into the potential economic implications of decisions that modify the treatment pathway.

METAShield: Hot Metallic Aeroshell Concept for RLV/SOV

NASA Technical Reports Server (NTRS)

Scotti, Stephen J.; Poteet, Carl C.; Daryabeigi, Kamran; Nowak, Robert J.; Hsu, Su-Yuen; Schmidt, Irvin H.; Ku, Shih-Huei P.

2003-01-01

An innovative fuselage design approach that combines many desirable operational features with a simple and efficient structural approach is being developed by NASA. The approach, named METAShield for MEtallic TransAtmospheric Shield, utilizes lightly loaded, hot aeroshell structures surrounding integral propellant tanks that carry the primary structural loads. The aeroshells are designed to withstand the local pressure loads, transmitting them to the tanks with minimal restraint of thermal growth. No additional thermal protection system protects the METAShield, and a fibrous or multilayer insulation blanket, located in the space between the aeroshell and the tanks, serves as both high temperature and cryogenic insulation for the tanks. The concept is described in detail, and the performance and operational features are highlighted. Initial design results and analyses of the structural, thermal, and thermal-structural performance are described. Computational results evaluating resistance to hypervelocity impact damage, as well as some supporting aerothermal wind tunnel results. are also presented. Future development needs are summarized.

Target rocks, impact glasses, and melt rocks from the Lonar crater, India: Highly siderophile element systematics and Sr-Nd-Os isotopic signatures

NASA Astrophysics Data System (ADS)

Schulz, Toni; Luguet, Ambre; Wegner, Wencke; Acken, David; Koeberl, Christian

2016-07-01

The Lonar crater is a ~0.57-Myr-old impact structure located in the Deccan Traps of the Indian peninsula. It probably represents the best-preserved impact structure hosted in continental flood basalts, providing unique opportunities to study processes of impact cratering in basaltic targets. Here we present highly siderophile element (HSE) abundances and Sr-Nd and Os isotope data for target basalts and impactites (impact glasses and impact melt rocks) from the Lonar area. These tools may enable us to better constrain the interplay of a variety of impact-related processes such as mixing, volatilization, and contamination. Strontium and Nd isotopic compositions of impactites confirm and extend earlier suggestions about the incorporation of ancient basement rocks in Lonar impactites. In the Re-Os isochron plot, target basalts exhibit considerable scatter around a 65.6 Myr Re-Os reference isochron, most likely reflecting weathering and/or magma replenishment processes. Most impactites plot at distinctly lower 187Re/188Os and 187Os/188Os ratios compared to the target rocks and exhibit up to two orders of magnitude higher abundances of Ir, Os, and Ru. Moreover, the impactites show near-chondritic interelement ratios of HSE. We interpret our results in terms of an addition of up to 0.03% of a chondritc component to most impact glasses and impact melt rocks. The magnitude of the admixture is significantly lower than the earlier reported 12-20 wt% of extraterrestrial component for Lonar impact spherules, reflecting the typical difference in the distribution of projectile component between impact glass spherules and bulk impactites.

Population genetic structure of moose (Alces alces) of South-central Alaska

USGS Publications Warehouse

Wilson, Robert E.; McDonough, John T.; Barboza, Perry S.; Talbot, Sandra L.; Farley, Sean D.

2015-01-01

The location of a population can influence its genetic structure and diversity by impacting the degree of isolation and connectivity to other populations. Populations at range margins are often thought to have less genetic variation and increased genetic structure, and a reduction in genetic diversity can have negative impacts on the health of a population. We explored the genetic diversity and connectivity between 3 peripheral populations of moose (Alces alces) with differing potential for connectivity to other areas within interior Alaska. Populations on the Kenai Peninsula and from the Anchorage region were found to be significantly differentiated (FST= 0.071, P < 0.0001) with lower levels of genetic diversity observed within the Kenai population. Bayesian analyses employing assignment methodologies uncovered little evidence of contemporary gene flow between Anchorage and Kenai, suggesting regional isolation. Although gene flow outside the peninsula is restricted, high levels of gene flow were detected within the Kenai that is explained by male-biased dispersal. Furthermore, gene flow estimates differed across time scales on the Kenai Peninsula which may have been influenced by demographic fluctuations correlated, at least in part, with habitat change.

Impact force identification for composite helicopter blades using minimal sensing

NASA Astrophysics Data System (ADS)

Budde, Carson N.

In this research a method for online impact identification using minimal sensors is developed for rotor hubs with composite blades. Modal impact data and the corresponding responses are recorded at several locations to develop a frequency response function model for each composite blade on the rotor hub. The frequency response model for each blade is used to develop an impact identification algorithm which can be used to identify the location and magnitude of impacts. Impacts are applied in two experimental setups, including a four-blade spin test rig and a cantilevered full-sized composite blade. The impacts are estimated to have been applied at the correct location 92.3% of the time for static fiberglass blades, 97.4% of the time for static carbon fiber blades and 99.2% of the time for a full sized-static blade. The estimated location is assessed further and determined to have been estimated in the correct chord position 96.1% of the time for static fiberglass, 100% of the time for carbon fiber blades and 99.2% of the time for the full-sized blades. Projectile impacts are also applied statically and during rotation to the carbon fiber blades on the spin test rig at 57 and 83 RPM. The applied impacts can be located to the correct position 63.9%, 41.7% and 33.3% for the 0, 57 and 83 RPM speeds, respectively, while the correct chord location is estimated 100% of the time. The impact identification algorithm also estimates the force of an impact with an average percent difference of 4.64, 2.61 and 1.00 for static fiberglass, full sized, and carbon fiber blades, respectively. Using a load cell and work equations, the force of impact for a projectile fired from a dynamic firing setup is estimated at about 400 N. The average force measured for applied projectile impacts to the carbon fiber blades, rotating at 0, 57 and 83 RPM, is 368.8, 373.7 and 432.4 N, respectively.

Comparative genomic analysis of oil spill impacts on deep water shipwreck microbiomes in the northern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Hamdan, L. J.; Damour, M.; McGown, C.; Figan, C.; Kassahun, Z.; Blackwell, K.; Horrell, C.; Gillevet, P.

2014-12-01

Shipwrecks serve as artificial reefs in the deep ocean. Because of their inherent diversity compared to their surrounding environment and their random distribution, shipwrecks are ideal ecosystems to study pollution impacts and microbial distribution patterns in the deep biosphere. This study provides a comparative assessment of Deepwater Horizon spill impacts on shipwreck and local sedimentary microbiomes and the synergistic effects of contaminants on these communities and the physical structures that support them. For this study, microbiomes associated with wooden 19th century shipwrecks and World War II era steel shipwrecks in the northern Gulf of Mexico were investigated using next generation sequencing. Samples derived from in situ biofilm monitoring platforms deployed adjacent to 5 shipwrecks for 4 months, and sediment collected from distances ranging from 2-200m from each shipwreck were evaluated for shifts in microbiome structure and gene function relative to proximity to the spill, and oil spill related contaminants in the local environment. The goals of the investigation are to determine impacts to recruitment and community structure at sites located within and outside of areas impacted by the spill. Taxonomic classification of dominant and rare members of shipwreck microbiomes and metabolic information extracted from sequence data yield new understanding of microbial processes associated with site formation. The study provides information on the identity of microbial inhabitants of shipwrecks, their role in site preservation, and impacts of the Deepwater Horizon spill on the primary colonizers of artificial reefs in the deep ocean. This approach could inform about the role of microorganisms in establishment and maintenance of the artificial reef environment, while providing information about ecosystem feedbacks resulting from spills.

Origin and emplacement of impactites in the Chesapeake Bay impact structure, Virginia, USA

USGS Publications Warehouse

Horton, J. Wright; Gohn, G.S.; Powars, D.S.; Edwards, L.E.

2007-01-01

The late Eocene Chesapeake Bay impact structure, located on the Atlantic margin of Virginia, may be Earth's best-preserved large impact structure formed in a shallow marine, siliciclastic, continental-shelf environment. It has the form of an inverted sombrero in which a central crater ???40 km in diameter is surrounded by a shallower brim, the annular trough, that extends the diameter to ???85 km. The annular trough is interpreted to have formed largely by the collapse and mobilization of weak sediments. Crystalline-clast suevite, found only in the central crater, contains clasts and blocks of shocked gneiss that likely were derived from the fragmentation of the central-uplift basement. The suevite and entrained megablocks are interpreted to have formed from impact-melt particles and crystalline-rock debris that never left the central crater, rather than as a fallback deposit. Impact-modified sediments in the annular trough include megablocks of Cretaceous nonmarine sediment disrupted by faults, fluidized sands, fractured clays, and mixed-sediment intercalations. These impact-modified sediments could have formed by a combination of processes, including ejection into and mixing of sediments in the water column, rarefaction-induced fragmentation and clastic injection, liquefaction and fluidization of sand in response to acoustic-wave vibrations, gravitational collapse, and inward lateral spreading. The Exmore beds, which blanket the entire crater and nearby areas, consist of a lower diamicton member overlain by an upper stratified member. They are interpreted as unstratified ocean-resurge deposits, having depositional cycles that may represent stages of inward resurge or outward anti-resurge flow, overlain by stratified fallout of suspended sediment from the water column. ?? 2008 The Geological Society of America. All rights reserved.

41 CFR 102-83.130 - When must agencies consider the impact of location decisions on low- and moderate-income employees?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 83-LOCATION OF SPACE Location of Space Application of... lease actions involving the relocation of a major work force must consider the impact on employees with...

41 CFR 102-83.130 - When must agencies consider the impact of location decisions on low- and moderate-income employees?

Code of Federal Regulations, 2011 CFR

2011-01-01

...) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 83-LOCATION OF SPACE Location of Space Application of... lease actions involving the relocation of a major work force must consider the impact on employees with...

41 CFR 102-83.130 - When must agencies consider the impact of location decisions on low- and moderate-income employees?

Code of Federal Regulations, 2014 CFR

2014-01-01

...) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 83-LOCATION OF SPACE Location of Space Application of... lease actions involving the relocation of a major work force must consider the impact on employees with...

41 CFR 102-83.130 - When must agencies consider the impact of location decisions on low- and moderate-income employees?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 83-LOCATION OF SPACE Location of Space Application of... lease actions involving the relocation of a major work force must consider the impact on employees with...

41 CFR 102-83.130 - When must agencies consider the impact of location decisions on low- and moderate-income employees?

Code of Federal Regulations, 2012 CFR

2012-01-01

...) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 83-LOCATION OF SPACE Location of Space Application of... lease actions involving the relocation of a major work force must consider the impact on employees with...

Proposed Continental Operations Range. United States Air Force.

DTIC Science & Technology

1974-06-01

when de -ailed plans are formulated to link H/W/D with COR/Nellis with a microwave system. Location of microwave repeaters in US Forest lands will be...be of significance. Supersonic activity is planned to avoid population areas, known structures, and random activities like known archaeological...to Land Use Plans and Policies 1-11 1.4’ Probable Impacts of the Proposed Action 1-13 1.5 Alternatives to the Proposed Action 1-19 1.6 Offsetting

GeoChip-based Analysis of Groundwater Microbial Diversity in Norman Landfill

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Zhenmei; He, Zhili; Parisi, Victoria

The Norman Landfill is a closed municipal solid waste landfill located on an alluvium associated with the Canadian River in Norman, Oklahoma. It has operated as a research site since 1994 because it is typical of many closed landfill sites across the U.S. Leachate from the unlined landfill forms a groundwater plume that extends downgradient approximately 250 m from the landfill toward the Canadian River. To investigate the impact of the landfill leachate on the diversity and functional structure of microbial communities, groundwater samples were taken from eight monitoring wells at a depth of 5m, and analyzed using a comprehensivemore » functional gene array covering about 50,000 genes involved in key microbial processes, such as biogeochemical cycling of C, N, P, and S, and bioremediation of organic contaminants and metals. Wells are located within a transect along a presumed flow path with different distances to the center of the leachate plume. Our analyses showed that microbial communities were obviously impacted by the leachate-component from the landfill. The number of genes detected and microbial diversity indices in the center (LF2B) and its closest (MLS35) wells were significantly less than those detected in other more downgradient wells, while no significant changes were observed in the relative abundance (i.e., percentage of each gene category) for most gene categories. However, the microbial community composition or structure of the landfill groundwater did not clearly show a significant correlation with the distance from well LF2B. Burkholderia sp. and Pseudomonas sp. were found to be the dominant microbial populations detected in all wells, while Bradyrhizobium sp. and Ralstonia sp. were dominant populations for seven wells except LF2B. In addition, Mantel test and canonical correspondence analysis (CCA) indicate that pH, sulfate, ammonia nitrogen and dissolved organic carbon (DOC) have significant effects on the microbial community structure. The results suggest that the leachate from unlined landfills significantly impact the structures of groundwater microbial communities, and that more distal wells recover by natural attenuation.« less

Combined X-ray and neutron fibre diffraction studies of biological and synthetic polymers

NASA Astrophysics Data System (ADS)

Parrot, I. M.; Urban, V.; Gardner, K. H.; Forsyth, V. T.

2005-08-01

The fibrous state is a natural one for polymer molecules which tend to assume regular helical conformations rather than the globular structures characteristic of many proteins. Fibre diffraction therefore has broad application to the study of a wide range of biological and synthetic polymers. The purpose of this paper is to illustrate the general scope of the method and in particular to demonstrate the impact of a combined approach involving both X-ray and neutron diffraction methods. While the flux of modern X-ray synchrotron radiation sources allows high quality datasets to be recorded with good resolution within a very short space of time, neutron studies can provide unique information through the ability to locate hydrogen or deuterium atoms that are often difficult or impossible to locate using X-ray methods. Furthermore, neutron fibre diffraction methods can, through the ability to selectively label specific parts of a structure, be used to highlight novel aspects of polymer structure that can not be studied using X-rays. Two examples are given. The first describes X-ray and neutron diffraction studies of conformational transitions in DNA. The second describes structural studies of the synthetic high-performance polymer poly(p-phenylene terephthalamide) (PPTA), known commercially as Kevlar® or Twaron®.

The importance of temperature fluctuations in understanding mosquito population dynamics and malaria risk.

PubMed

Beck-Johnson, Lindsay M; Nelson, William A; Paaijmans, Krijn P; Read, Andrew F; Thomas, Matthew B; Bjørnstad, Ottar N

2017-03-01

Temperature is a key environmental driver of Anopheles mosquito population dynamics; understanding its central role is important for these malaria vectors. Mosquito population responses to temperature fluctuations, though important across the life history, are poorly understood at a population level. We used stage-structured, temperature-dependent delay-differential equations to conduct a detailed exploration of the impacts of diurnal and annual temperature fluctuations on mosquito population dynamics. The model allows exploration of temperature-driven temporal changes in adult age structure, giving insights into the population's capacity to vector malaria parasites. Because of temperature-dependent shifts in age structure, the abundance of potentially infectious mosquitoes varies temporally, and does not necessarily mirror the dynamics of the total adult population. In addition to conducting the first comprehensive theoretical exploration of fluctuating temperatures on mosquito population dynamics, we analysed observed temperatures at four locations in Africa covering a range of environmental conditions. We found both temperature and precipitation are needed to explain the observed malaria season in these locations, enhancing our understanding of the drivers of malaria seasonality and how temporal disease risk may shift in response to temperature changes. This approach, tracking both mosquito abundance and age structure, may be a powerful tool for understanding current and future malaria risk.

Effects of computing parameters and measurement locations on the estimation of 3D NPS in non-stationary MDCT images.

PubMed

Miéville, Frédéric A; Bolard, Gregory; Bulling, Shelley; Gudinchet, François; Bochud, François O; Verdun, François R

2013-11-01

The goal of this study was to investigate the impact of computing parameters and the location of volumes of interest (VOI) on the calculation of 3D noise power spectrum (NPS) in order to determine an optimal set of computing parameters and propose a robust method for evaluating the noise properties of imaging systems. Noise stationarity in noise volumes acquired with a water phantom on a 128-MDCT and a 320-MDCT scanner were analyzed in the spatial domain in order to define locally stationary VOIs. The influence of the computing parameters in the 3D NPS measurement: the sampling distances bx,y,z and the VOI lengths Lx,y,z, the number of VOIs NVOI and the structured noise were investigated to minimize measurement errors. The effect of the VOI locations on the NPS was also investigated. Results showed that the noise (standard deviation) varies more in the r-direction (phantom radius) than z-direction plane. A 25 × 25 × 40 mm(3) VOI associated with DFOV = 200 mm (Lx,y,z = 64, bx,y = 0.391 mm with 512 × 512 matrix) and a first-order detrending method to reduce structured noise led to an accurate NPS estimation. NPS estimated from off centered small VOIs had a directional dependency contrary to NPS obtained from large VOIs located in the center of the volume or from small VOIs located on a concentric circle. This showed that the VOI size and location play a major role in the determination of NPS when images are not stationary. This study emphasizes the need for consistent measurement methods to assess and compare image quality in CT. Copyright © 2012 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Reliability of an experimental method to analyse the impact point on a golf ball during putting.

PubMed

Richardson, Ashley K; Mitchell, Andrew C S; Hughes, Gerwyn

2015-06-01

This study aimed to examine the reliability of an experimental method identifying the location of the impact point on a golf ball during putting. Forty trials were completed using a mechanical putting robot set to reproduce a putt of 3.2 m, with four different putter-ball combinations. After locating the centre of the dimple pattern (centroid) the following variables were tested; distance of the impact point from the centroid, angle of the impact point from the centroid and distance of the impact point from the centroid derived from the X, Y coordinates. Good to excellent reliability was demonstrated in all impact variables reflected in very strong relative (ICC = 0.98-1.00) and absolute reliability (SEM% = 0.9-4.3%). The highest SEM% observed was 7% for the angle of the impact point from the centroid. In conclusion, the experimental method was shown to be reliable at locating the centroid location of a golf ball, therefore allowing for the identification of the point of impact with the putter head and is suitable for use in subsequent studies.

Bioinspired engineering study of Plantae vascules for self-healing composite structures.

PubMed

Trask, R S; Bond, I P

2010-06-06

This paper presents the first conceptual study into creating a Plantae-inspired vascular network within a fibre-reinforced polymer composite laminate, which provides an ongoing self-healing functionality without incurring a mass penalty. Through the application of a 'lost-wax' technique, orthogonal hollow vascules, inspired by the 'ray cell' structures found in ring porous hardwoods, were successfully introduced within a carbon fibre-reinforced epoxy polymer composite laminate. The influence on fibre architecture and mechanical behaviour of single vascules (located on the laminate centreline) when aligned parallel and transverse to the local host ply was characterized experimentally using a compression-after-impact test methodology. Ultrasonic C-scanning and high-resolution micro-CT X-ray was undertaken to identify the influence of and interaction between the internal vasculature and impact damage. The results clearly show that damage morphology is influenced by vascule orientation and that a 10 J low-velocity impact damage event is sufficient to breach the vasculature; a prerequisite for any subsequent self-healing function. The residual compressive strength after a 10 J impact was found to be dependent upon vascule orientation. In general, residual compressive strength decreased to 70 per cent of undamaged strength when vasculature was aligned parallel to the local host ply and a value of 63 per cent when aligned transverse. This bioinspired engineering study has illustrated the potential that a vasculature concept has to offer in terms of providing a self-healing function with minimum mass penalty, without initiating premature failure within a composite structure.

Understanding Long-Term Variations in an Elephant Piosphere Effect to Manage Impacts

PubMed Central

Landman, Marietjie; Schoeman, David S.; Hall-Martin, Anthony J.; Kerley, Graham I. H.

2012-01-01

Surface water availability is a key driver of elephant impacts on biological diversity. Thus, understanding the spatio-temporal variations of these impacts in relation to water is critical to their management. However, elephant piosphere effects (i.e. the radial pattern of attenuating impact) are poorly described, with few long-term quantitative studies. Our understanding is further confounded by the complexity of systems with elephant (i.e. fenced, multiple water points, seasonal water availability, varying population densities) that likely limit the use of conceptual models to predict these impacts. Using 31 years of data on shrub structure in the succulent thickets of the Addo Elephant National Park, South Africa, we tested elephant effects at a single water point. Shrub structure showed a clear sigmoid response with distance from water, declining at both the upper and lower limits of sampling. Adjacent to water, this decline caused a roughly 300-m radial expansion of the grass-dominated habitats that replace shrub communities. Despite the clear relationship between shrub structure and ecological functioning in thicket, the extent of elephant effects varied between these features with distance from water. Moreover, these patterns co-varied with other confounding variables (e.g. the location of neighboring water points), which limits our ability to predict such effects in the absence of long-term data. We predict that elephant have the ability to cause severe transformation in succulent thicket habitats with abundant water supply and elevated elephant numbers. However, these piosphere effects are complex, suggesting that a more integrated understanding of elephant impacts on ecological heterogeneity may be required before water availability is used as a tool to manage impacts. We caution against the establishment of water points in novel succulent thicket habitats, and advocate a significant reduction in water provisioning at our study site, albeit with greater impacts at each water point. PMID:23028942

Understanding long-term variations in an elephant piosphere effect to manage impacts.

PubMed

Landman, Marietjie; Schoeman, David S; Hall-Martin, Anthony J; Kerley, Graham I H

2012-01-01

Surface water availability is a key driver of elephant impacts on biological diversity. Thus, understanding the spatio-temporal variations of these impacts in relation to water is critical to their management. However, elephant piosphere effects (i.e. the radial pattern of attenuating impact) are poorly described, with few long-term quantitative studies. Our understanding is further confounded by the complexity of systems with elephant (i.e. fenced, multiple water points, seasonal water availability, varying population densities) that likely limit the use of conceptual models to predict these impacts. Using 31 years of data on shrub structure in the succulent thickets of the Addo Elephant National Park, South Africa, we tested elephant effects at a single water point. Shrub structure showed a clear sigmoid response with distance from water, declining at both the upper and lower limits of sampling. Adjacent to water, this decline caused a roughly 300-m radial expansion of the grass-dominated habitats that replace shrub communities. Despite the clear relationship between shrub structure and ecological functioning in thicket, the extent of elephant effects varied between these features with distance from water. Moreover, these patterns co-varied with other confounding variables (e.g. the location of neighboring water points), which limits our ability to predict such effects in the absence of long-term data. We predict that elephant have the ability to cause severe transformation in succulent thicket habitats with abundant water supply and elevated elephant numbers. However, these piosphere effects are complex, suggesting that a more integrated understanding of elephant impacts on ecological heterogeneity may be required before water availability is used as a tool to manage impacts. We caution against the establishment of water points in novel succulent thicket habitats, and advocate a significant reduction in water provisioning at our study site, albeit with greater impacts at each water point.

A GIS Representation of 1964 Tsunami Damage in Crescent City, California

NASA Astrophysics Data System (ADS)

Velasco Campos, C. J.; Dengler, L. A.

2013-12-01

The March 1964 Alaska tsunami caused major damage in Alaska and also impacted the west coast of North America. Crescent City, California, 3000 km away from the source region, suffered the greatest damage outside Alaska. Twenty-nine blocks of the downtown and harbor areas were inundated and nearly 300 homes and businesses damaged or destroyed. In the aftermath of the tsunami, numerous maps, reports and photographs of the impacts in Crescent City were released, some by engineers and scientists, and much by individuals and the popular press. The Del Norte Historical Society has a large amount of archival material (photographs and eye witness accounts) from the tsunami, much of which has never been thoroughly examined or correlated with other reports. In this study, we assemble all of the available information from these disparate sources into a GIS framework in order to examine the 1964 Crescent City damage in a systematic way and provide a quantitative framework for others who are modeling tsunami impacts. Using ArcGIS 10, old aerial photos, tsunami inundation maps, and photographs were georeferenced to produce GIS layers of 'before and after' Crescent City. Hyperlinks were created to connect photos with their locations in present day. We reference damage to a layer showing Magoon's 1968 map of inundation depth and extent. Structural damage falls into four main groupings: structures floated off of foundations, damage by impact from debris, pressure differences from water infilling structures, and fire. 15 structures were moved off of foundations, all in the direction of the outgoing flow. We also create layers of the structures of the modern city and the predicted tsunami run-up from a Cascadia event. Magoon, Orville T., 1966, Structural Damage by Tsunamis, Proceedings, American Society Civil Engineers, Specialty Conference on Coastal Engineering, Santa Barbara (California), Oct. 1965, pp. 35-68

Comparisons of the Impact Responses of a 1/5-Scale Model and a Full-Scale Crashworthy Composite Fuselage Section

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Fasanella, Edwin L.; Lyle, Karen H.

2003-01-01

A 25-fps vertical drop test of a 1/5-scale model composite fuselage section was conducted to replicate a previous test of a full-scale fuselage section. The purpose of the test was to obtain experimental data characterizing the impact response of the 1/5-scale model fuselage section for comparison with the corresponding full-scale data. This comparison is performed to assess the scaling procedures and to determine if scaling effects are present. For the drop test, the 1/5-scale model fuselage section was configured in a similar manner as the full-scale section, with lead masses attached to the floor through simulated seat rails. Scaled acceleration and velocity responses are compared and a general assessment of structural damage is made. To further quantify the data correlation, comparisons of the average acceleration data are made as a function of floor location and longitudinal position. Also, the percentage differences in the velocity change (area under the acceleration curve) and the velocity change squared (proportional to kinetic energy) are compared as a function of floor location. Finally, correlation coefficients are calculated for corresponding 1/5- and full-scale data channels and these values are plotted versus floor location. From a scaling perspective, the differences between the 1/5- and full-scale tests are relatively small, indicating that appropriate scaling procedures were used in fabricating the test specimens and in conducting the experiments. The small differences in the scaled test data are attributed to minor scaling anomalies in mass, potential energy, and impact attitude.

Peleolakes and impact basins in southern Arabia Terra, including Meridiani Planum: Implications for the formation of hematite deposits on Mars

USGS Publications Warehouse

Newsom, Horton E.; Barber, C.A.; Hare, T.M.; Schelble, R.T.; Sutherland, V.A.; Feldman, W.C.

2003-01-01

The hematite deposit in Meridiani Planum was selected for a Mars Exploration Rover (MER) landing site because water could be involved in the formation of hematite, and water is a key ingredient in the search for life. Our discovery of a chain of paleolake basins and channels along the southern margin of the hematite deposits in Meridiani Planum with the presence of the strongest hematite signature adjacent to a paleolake basin, supports the possible role of water in the formation of the hematite and the deposition of other layered materials in the region. The hematite may have formed by direct precipitation from lake water, as coatings precipitated from groundwater, or by oxidation of preexisting iron oxide minerals. The paleolake basins were fed by an extensive channel system, originating from an area larger than Texas and located south of the Schiaparelli impact basin. On the basis of stratigraphic relationships, the formation of channels in the region occurred over much of Mars' history, from before the layered materials in Meridiani Planum were deposited until recently. The location of the paleolake basins and channels is connected with the impact cratering history of the region. The earliest structure identified in this study is an ancient circular multiringed basin (800-1600 km diameter) that underlies the entire Meridiani Planum region. The MER landing site is located on the buried northern rim of a later 150 km diameter crater. This crater is partially filled with layered deposits that contained a paleolake in its southern portion. Copyright 2003 by the American Geophysical Union.

Can mental health and readjustment be improved in UK military personnel by a brief period of structured postdeployment rest (third location decompression)?

PubMed

Jones, Norman; Jones, Margaret; Fear, Nicola T; Fertout, Mohammed; Wessely, Simon; Greenberg, Neil

2013-07-01

Third Location Decompression (TLD) is an activity undertaken by UK Armed Forces (UK AF) personnel at the end of an operational deployment which aims to smooth the transition between operations and returning home. We assessed whether TLD impacted upon both mental health and postdeployment readjustment. Data collected during a large cohort study was examined to identify personnel who either engaged in TLD or returned home directly following deployment. Propensity scores were generated and used to calculate inverse probability of treatment weights in adjusted regression analyses to compare mental health outcomes and postdeployment readjustment problems. TLD had a positive impact upon mental health outcomes (post-traumatic stress disorder (PTSD) and multiple physical symptoms) and levels of harmful alcohol use. However, when the samples were stratified by combat exposure, although postdeployment readjustment was similar for all exposure levels, personnel experiencing low and moderate levels of combat exposure experienced the greatest positive mental health effects. We found no evidence to suggest that TLD promotes better postdeployment readjustment; however, we found a positive impact upon alcohol use and mental health with an interaction with degree of combat exposure. This study suggests that TLD is a useful postdeployment transitional activity that may help to improve PTSD symptoms and alcohol use in UK AF personnel.

Validation of a noninvasive system for measuring head acceleration for use during boxing competition.

PubMed

Beckwith, Jonathan G; Chu, Jeffrey J; Greenwald, Richard M

2007-08-01

Although the epidemiology and mechanics of concussion in sports have been investigated for many years, the biomechanical factors that contribute to mild traumatic brain injury remain unclear because of the difficulties in measuring impact events in the field. The purpose of this study was to validate an instrumented boxing headgear (IBH) that can be used to measure impact severity and location during play. The instrumented boxing headgear data were processed to determine linear and rotational acceleration at the head center of gravity, impact location, and impact severity metrics, such as the Head Injury Criterion (HIC) and Gadd Severity Index (GSI). The instrumented boxing headgear was fitted to a Hybrid III (HIII) head form and impacted with a weighted pendulum to characterize accuracy and repeatability. Fifty-six impacts over 3 speeds and 5 locations were used to simulate blows most commonly observed in boxing. A high correlation between the HIII and instrumented boxing headgear was established for peak linear and rotational acceleration (r2= 0.91), HIC (r2 = 0.88), and GSI (r2 = 0.89). Mean location error was 9.7 +/- 5.2 masculine. Based on this study, the IBH is a valid system for measuring head acceleration and impact location that can be integrated into training and competition.

The Impact of the Rock Mass Deformation on Geometric Changes of a Historical Chimney in the Salt Mine of Bochnia

NASA Astrophysics Data System (ADS)

Szafarczyk, Anna; Gawałkiewicz, Rafał

2018-03-01

There are many ways of the geometry measurement of slim objects, with the application of geodetic and photogrammetric methods. A modern solution in the diagnostics of slim objects is the application of laser scanning, with the use of a scanner of a scanning total station. The point cloud, obtained from the surface of the scanned object gives the possibility of generating not only information on structural surface deformations, but also facilitates obtaining the data on the geometry of the axis of the building, as a basic indicator of the characteristics of its deformation. The cause of the change in the geometry of slim objects is the impact of many external and internal factors. These objects are located in the areas of working or closed underground mines. They can be impacted by the ground and they can face the results of the convergence of cavities. A specific structure of the salt rock mass causes subsequent convergence of the post-exploitation cavities, which has the influence on the behaviour of the terrain surface and the related objects. The authors analysed the impact of the changes in the rock mass and the surface on the changes of the industrial chimney in the Bochnia Salt Mine.

White matter compromise predicts poor intellectual outcome in survivors of pediatric low-grade glioma.

PubMed

Liu, Fang; Scantlebury, Nadia; Tabori, Uri; Bouffet, Eric; Laughlin, Suzanne; Strother, Douglas; McConnell, Dina; Hukin, Juliette; Fryer, Chris; Brière, Marie-Eve; Montour-Proulx, Isabelle; Keene, Daniel; Wang, Frank; Mabbott, Donald J

2015-04-01

While the impact of cranial radiation on white matter following treatment for pediatric brain tumor has been the focus of many recent studies, the effect of treatment in the absence of radiation has received little attention. The relations between white matter and cognitive outcome have not been explored in patients who have undergone radiation-free treatment. As most patients treated without cranial radiation survive long after their diagnosis, it is critical to identify factors that may impact structural and neurocognitive outcomes. Using diffusion tensor imaging, we examined white matter structure in 32 patients with pediatric low-grade glioma (PLGG) (19 with subtentorial location and 13 with supratentorial location) and 32 healthy participants. Indices of intellectual functioning were also evaluated. Radiation was not used to treat this cohort, aged 8-19 years. We detected evidence of deficits in IQ and compromised supra- and subtentorial white matter in patients relative to healthy children (P < .05). Compromise of supratentorial white matter mediated the impact of treatment for PLGG on IQ. Greater white matter compromise was observed in patients who presented without multiple symptoms, were treated with biopsy/no surgery, had positive neurofibromatosis 1 status, were younger age at diagnosis, and whose parents had lower levels of education (P < .05). Our findings provide evidence of increased risk of intellectual and white matter compromise in patients treated for PLGG without radiation. We identify a neural origin of cognitive deficit useful for predicting outcome and mitigating long-term adverse effects in pediatric brain tumor patients treated without cranial radiation. © The Author(s) 2014. Published by Oxford University Press on behalf of the Society for Neuro-Oncology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Outsourcing versus in-house maintenance of medical devices: a longitudinal, empirical study.

PubMed

Miguel-Cruz, Antonio; Rios-Rincón, Adriana; Haugan, Gregory L

2014-03-01

To determine what factors have a significant influence on the performance of medical device maintenance outsourcing, and to determine how the performance of external governance structures differs depending on whether a hospital is private or public. This was a longitudinal study of 590 maintenance transactions at 20 hospitals in Bogotá, Colombia, involving 764 medical devices and 72 maintenance service providers. Maintenance performance data (i.e., turn-around time in hours; TAT) for the service providers (either in-house or outsourced) were primarily collected over a 20-month period, from December 2009-August 2011, by means of a monitoring procedure; then, a hazards model was run. The availability of specific repair parts, in-stock, in the city in which the medical devices were located, had a positive impact on the performance of both internal and external governance structures. Online service also had a positive impact on both, with a stronger positive impact on the performance of internal governance than on that of external governance. For transactions governed by external structures, better performance was seen in private hospitals than in public ones. In public health institutions, internal governance showed better performance than external governance. Both internal and external governance structures showed better performance in private healthcare institutions than in public ones. In public health institutions, internal governance shows better performance than external governance; this suggests that healthcare managers should reconsider the trend to eliminate in-house maintenance service staff in public healthcare institutions.

United States Navy - Canadian forces solid state flight data recorder/crash position locator experiment on the B-720 controlled impact demonstration

NASA Technical Reports Server (NTRS)

Watters, D. M.

1986-01-01

The operation of a radio beacon position locator during and after the remotely controlled transport aircraft is discussed. The radio beacon transmission was actuated and was picked up by the Navy P-3A chase aircraft for a short time, after which reception was lost. The pilot reported that he received a signal on both 121.5 MHz and 243 MHz for a period of approximately 5 seconds. Five minutes after the crash a portable direction finding unit located on the roof of the NASA Dryden Flight Research Facility, 4 miles distant from the crash, was unable to pick up the beacon transmission. The fire crews started fighting the fires approximately 90 seconds after the time of impact. Navy personnel access to the crash site was allowed on the morning of December 2, 1984. Radio beacon locator was found resting top side up, 15 feet forward and 13 feet perpendicular from the tray location the starboard side of the aircraft. An immediate inspection indicated the airfoil suffered moderate fire damage with paint peeling but not intumescing. The visual marker strobe lamp housings were intact but extensively burned such that it was impossible to see if the lamps had survived. The airfoil suffered minor structural damage, with assorted dents, etc. The extended plunger on the ARU-21 release unit indicated that the pyrotechnic deployment system operated. The radio beacon base (tray) suffered some heat and fire damage, and was charred and blackened by smoke. The frangible switch in the nose survived and the switch in the belly was recovered and found to have actuated. It is assumed that this switch fired the ARU-21 squib. There were no other release switches installed in the normally open system in the aircraft.

The ecological impact assessment of a proposed road development (the Slovak approach)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Igondova, Erika, E-mail: erika.igondova@gmail.com; Pavlickova, Katarina, E-mail: pavlickova60@gmail.com; Majzlan, Oto, E-mail: majzlan@fns.uniba.sk

The construction of roads is one of the most widespread forms of natural landscape modification. Over the last 20 years, dozens of road constructions have been assessed in Slovakia, which makes it possible to talk about methodological positives and negatives. A special feature of Slovakia is that many planned or renovated roads are located in protected areas or are in contact with them (including Natura 2000 sites). Therefore, it is important to understand the scope of the roads' ecological impacts and find ways for their appropriate evaluation and incorporation into the Environmental Impact Assessment process. For this reason, the Ecologicalmore » Impact Assessment methodology can be used as a basis for our research, which consists of three stages. In the first stage (scoping), a buffer circumventing the proposed road is created to determine the area for impact prediction and evaluation. Subsequently, the landscape structure and baseline landscape conditions are discussed, a map of current landscape structure is created and the current ecological status of the affected area is calculated. In the second stage (the evaluation of ecological resources), important ecological parts of the landscape are delineated. This step is based on the importance of previous information and its vulnerability, and leads to the mapping of the road ecological impact zone. In the third stage (impact assessment), important ecological parts are spatially correlated with the proposed road construction. Finally, the significance of ecological impacts of the activity is evaluated by applying specific criteria (duration, reversibility, magnitude, size and road ecological impact zone significance). A scale is proposed for each criterion to evaluate the total significance of impacts. In this way, detailed significant ecological impacts can be found which will help lead to proposed correct mitigation measures and a post-project analysis. - Highlights: • This paper proposes a methodology for the EcIA of road construction. • It tries to understand the spatial structure and configuration of landscape elements. • The most important ecological parts within the territory are identified. • The total significance of ecological receptors is evaluated by applying criteria.« less

The spatial and metabolic basis of colony size variation.

PubMed

Chacón, Jeremy M; Möbius, Wolfram; Harcombe, William R

2018-03-01

Spatial structure impacts microbial growth and interactions, with ecological and evolutionary consequences. It is therefore important to quantitatively understand how spatial proximity affects interactions in different environments. We tested how proximity influences colony size when either Escherichia coli or Salmonella enterica are grown on various carbon sources. The importance of colony location changed with species and carbon source. Spatially explicit, genome-scale metabolic modeling recapitulated observed colony size variation. Competitors that determine territory size, according to Voronoi diagrams, were the most important drivers of variation in colony size. However, the relative importance of different competitors changed through time. Further, the effect of location increased when colonies took up resources quickly relative to the diffusion of limiting resources. These analyses made it apparent that the importance of location was smaller than expected for experiments with S. enterica growing on glucose. The accumulation of toxic byproducts appeared to limit the growth of large colonies and reduced variation in colony size. Our work provides an experimentally and theoretically grounded understanding of how location interacts with metabolism and diffusion to influence microbial interactions.

Impact detection system

NASA Technical Reports Server (NTRS)

Byers, Terry (Inventor); Gibbons, Frank L. (Inventor); Christiansen, Eric L. (Inventor)

2010-01-01

In an embodiment, an apparatus and method capable of determining the time and location of a projectile's impact is disclosed. In another embodiment, an apparatus and method capable of determining the time and location of a projectile's impact as well as the direction from whence the projectile came is disclosed.

Impact of intermodal facilities to the design of supply chains for biorefineries.

DOT National Transportation Integrated Search

2009-08-15

This paper analyzes the impact that an intermodal facility has on location and transportation decisions for biofuel production plants. Location decisions impact the management of the in-bound and out-bound logistics of a plant. We model this supply c...

The Mechanics of Impact Basin Formation: Comparisons between Modeling and Geophysical Observations

NASA Astrophysics Data System (ADS)

Stewart, S. T.

2010-12-01

Impact basins are the largest geologic structures on planetary surfaces. Single or multiple ring-shaped scarps or arcuate chains of massifs typically surround basin-sized craters (e.g., larger than about 300 km diameter on the moon [1]). Impact basins also possess central mass anomalies related to ejection of a portion of the crust (and mantle) and uplift of the mantle. I will discuss insights into the mechanics of impact basin formation derived from numerical simulations and focus on features that may be compared with gravity and topography data. The simulations of basin formation use the method of [2] with an improved rheological model that includes dynamic weakening of faults and more accurate treatment of the mantle solidus. Two-dimensional simulations of vertical impacts onto spherical planets utilize a central gravity field, and three-dimensional simulations of oblique impacts include a self-gravity calculation. During the opening and collapse of the transient crater, localization of strain leads to deformation features that are interpreted as deep faults through the lithosphere. Based on simulations of mantle-excavating impacts onto the moon and Mars with thermal gradients that intersect the solidus in the asthenosphere, the final impact structure has three major features: (i) an inner basin filled with melt and bounded by the folded lithosphere, (ii) a broad shallow terrace of faulted and translated lithosphere with an ejecta deposit, and (iii) the surrounding autochthonous lithosphere with radially thinning ejecta. The folded lithosphere is a complex structure that experiences translation inward and then outward again during collapse of the transient cavity. The uplifted mantle within this structure is overlain by a thin layer of hot crustal material. In addition to asymmetry in the excavated material, 45-degree impact events produce an asymmetric terrace feature. The principal observations for comparison to the calculations are the inferred locations of major ring structures (derived from topography and geologic mapping) and the crustal thickness and mantle topography (derived from gravity and topography) [see also 3]. Preliminary comparisons indicate that the simulations produce the major features in the observations. I will present detailed comparisons between simulations and observations for major basins on the moon, including South Pole-Aitken, for different initial lithospheric thicknesses and thermal gradients. [1] Spudis, P.D. (1993) The Geology of Multi-Ring Impact basins: Cambridge University Press. [2] Senft, L.E. and S.T. Stewart (2009) Earth and Planetary Science Letters 287, 471-482. [3] Lillis, R.J., et al. (2010) AGU Fall Meeting.

Engineering Copper Carboxylate Functionalities on Water Stable Metal–Organic Frameworks for Enhancement of Ammonia Removal Capacities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joshi, Jayraj N.; Garcia-Gutierrez, Erika Y.; Moran, Colton M.

Functionalization of copper carboxylate groups on a series of UiO-66 metal organic framework (MOF) analogues and their corresponding impact on humid and dry ammonia adsorption behavior were studied. Relative locations of possible carboxylic acid binding sites for copper on the MOF analogues were varied on ligand and missing linker defect sites. Materials after copper incorporation exhibited increased water vapor and ammonia affinity during isothermal adsorption and breakthrough experiments, respectively. The introduction of copper markedly increased ammonia adsorption capacities for all adsorbents possessing carboxyl binding sites. In particular, the new MOF UiO-66-(COOCu)2 displayed the highest ammonia breakthrough capacities of 6.38 andmore » 6.84 mmol g–1 under dry and humid conditions, respectively, while retaining crystallinity and porosity. Relative carboxylic acid site locations were also found to impact sorbent stability, as missing linker defect functionalized materials degraded under humid conditions after copper incorporation. Postsynthetic metal insertion provides a method for adding sites that are analogous to open metal sites while maintaining good structural stability.« less

Contamination, misuse and abuse of the global oceans leading to ecosystem damage and destruction, health consequences and international conflict

NASA Technical Reports Server (NTRS)

1975-01-01

Unregulated uses of the oceans may threaten the global ecological balance, alter plant and animal life and significantly impact the global climatic systems. Recent plans to locate large scale structures on the oceans and to exploit the mineral riches of the seas pose even greater risk to the ecological system. Finally, increasing use of the oceans for large scale transport greatly enhances the probability of collision, polluting spills and international conflict.

Standoff spectroscopic interrogation of samples irradiated by high energy lasers

NASA Astrophysics Data System (ADS)

Daigle, Jean-François; Pudo, Dominik; Théberge, Francis

2017-10-01

We report on a novel method that shows the potential to provide real-time, standoff forensic analysis of samples being irradiated by a high energy laser (HEL). The interaction of the HEL beam with matter produces specific optical signatures that can be detected from the location of the HEL system. A spectroscopic analysis of these signals can then provide useful information to the operator including the impact the laser has on the sample as well as providing data about the its structure and composition.

United States Air Force Summer Research Program 1991. Graduate Student Research Program (GSRP) Reports. Volume 9. Wright Laboratory

DTIC Science & Technology

1992-01-09

Materials 22 Deply of Laminated Panels with Perforation due to Impact John Lair 23 Actuator Location and Optimal Control Design for Flexible Structures...procedure is the focusing and alignment of the UV souce. Though the output of a vapor lamp is nonuniform ., intensity peaks can be smoothed by expanding the...surface, localized surface heatig may occur. Secondly, the output of a mercury vapor lame is nonuniform , requiring diffusion tc obtain a more- uniform

Evaluation of commercial utility of ERTS-A imagery in structural reconnaissance for minerals and petroleum

NASA Technical Reports Server (NTRS)

Saunders, D. F. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Initial analytical results in Area 3 have been very encouraging. Not only have new major lineaments been detected but many of the intersections of those lineaments correlate with the general location of known mineral deposits while others appear to outline petroleum-bearing basins and uplifts. If later analyses confirm these results the economic impact of ERTS type imagery could be very significant in worldwide mineral and petroleum reconnaissance.

Exterior view of north and east exterior walls of LongTerm ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Exterior view of north and east exterior walls of Long-Term Oxidizer Silo (T-28B), looking south. Silo was designed to assess long-term environmental impacts on storage of the Titan II's oxidizer (nitrogen tetroxide). The shorter Oxidizer Conditioning Structure (T-28D) is located behind and to the immediate left of T-28B - Air Force Plant PJKS, Systems Integration Laboratory, Long-Term Oxidizer Silo, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Proposed Relocation of the 37th Tactical Fighter Wing and Other Tactical Force Structure Actions. Draft Environmental Impact Statement

DTIC Science & Technology

1991-02-05

finance , insurance and real estate FL flight level ft feet FWS U.S. Fish and Wildlife Service FWW Fighter Weapon Wing FY fiscal year GAF German Air Force...three locations are related to socioeconomics. Potential effects of the realignment on employment, income, public finance , housing, and local economic...Manufacturing 89 107 1 Transportation, communications, and utilities 135 202 2 * Wholesale and retail tradeb 514 594 5 3 Finance , insurance, and real estate 216

Cape Cod Easterly Shore Beach Erosion Study. Volume 2

DTIC Science & Technology

1979-04-01

exploration leases in itself does not affect land use, but the discovery of oil , gas , or minerals offshore can have a major impact on the coast if...Structures - A few seasonal cottages are located s) uth of and on the southeast side of Little Pochet Island (Figure 1-G3). They are reached by jeep trail...unknown, but many of the offshore islands and submerged banks of the area are of glacial origin. Noteworthy examples are the Nantucket shoals southeast

Saccades to a remembered location elicit spatially-specific activation in human retinotopic visual cortex

PubMed Central

Geng, Joy J.; Ruff, Christian C.; Driver, Jon

2008-01-01

The possible impact upon human visual cortex from saccades to remembered target locations was investigated using fMRI. A specific location in the upper-right or upper-left visual quadrant served as the saccadic target. After a delay of 2400 msecs, an auditory signal indicated whether to execute a saccade to that location (go trial) or to cancel the saccade and remain centrally fixated (no-go). Group fMRI analysis revealed activation specific to the remembered target location for executed saccades, in contralateral lingual gyrus. No-go trials produced similar, albeit significantly reduced effects. Individual retinotopic mapping confirmed that on go trials, quadrant-specific activations arose in those parts of ventral V1, V2, and V3 that coded the target location for the saccade, whereas on no-go trials only the corresponding parts of V2 and V3 were significantly activated. These results indicate that a spatial-motor saccadic task (i.e. making an eye-movement to a remembered location) is sufficient to activate retinotopic visual cortex spatially corresponding to the target location, and that this activation is also present (though reduced) when no saccade is executed. We discuss the implications of finding that saccades to remembered locations can affect early visual cortex, not just those structures conventionally associated with eye-movements, in relation to recent ideas about attention, spatial working memory, and the notion that recently activated representations can be ‘refreshed’ when needed. PMID:18510442

Evaluating confidence in the impact of regulatory nutrient reduction and assessing the competing impact of climate change

NASA Astrophysics Data System (ADS)

Irby, I.; Friedrichs, M. A. M.

2017-12-01

Human impacts on the Chesapeake Bay through increased nutrient run-off as a result of land-use change, urbanization, and industrialization, have resulted in a degradation of water quality over the last half-century. These direct impacts, compounded with human-induced climate changes such as warming, rising sea level, and changes in precipitation, have elevated the conversation surrounding the future of the Bay's water quality. As a result, in 2010, a Total Maximum Daily Load (TMDL) was established for the Chesapeake Bay that limited nutrient and sediment input in an effort to increase dissolved oxygen. This research utilizes a multiple model approach to evaluate confidence in the estuarine water quality modeling portion of the TMDL. One of the models is then used to assess the potential impact climate change may have on the success of currently mandated nutrient reduction levels in 2050. Results demonstrate that although the models examined differ structurally and in biogeochemical complexity, they project a similar attainment of regulatory water quality standards after nutrient reduction, while also establishing that meeting water quality standards is relatively independent of hydrologic conditions. By developing a Confidence Index, this research identifies the locations and causes of greatest uncertainty in modeled projections of water quality. Although there are specific locations and times where the models disagree, this research lends an increased degree of confidence in the appropriateness of the TMDL levels and in the general impact nutrient reductions will have on Chesapeake Bay water quality under current environmental conditions. However, when examining the potential impacts of climate change, this research shows that the combined impacts of increasing temperature, sea level, and river flow negatively affect dissolved oxygen throughout the Chesapeake Bay and impact progress towards meeting the water quality standards associated with the TMDL with increased temperature as the primary culprit. These results, having been continually shared with the regulatory TMDL modelers, will aid in the decision making for the 2017 TMDL Mid-Point Assessment.

Analyzing the impact of intermodal facilities to the design and management of biofuels supply chain.

DOT National Transportation Integrated Search

2010-01-01

This paper analyzes the impact that an intermodal facility has on location and transportation : decisions for biofuel production plants. Location decisions impact the management of the in-bound and out-bound logistics of a plant. We model this supply...

Role of reinforcement couplers in serviceability performance of concrete members

NASA Astrophysics Data System (ADS)

Ng, P. L.; Guan, G. X.; Kwan, A. K. H.

2017-10-01

Connection of reinforcing bars by couplers is a common form of reinforcement splicing. However, the variation of stiffness at the location of couplers and the potentially excessive residual slips are suspected to cause adverse impact on the serviceability, especially for structural members subjected to repeated loading. This paper studies the role of couplers in the serviceability performance of concrete members. Relevant provisions in design codes are reviewed and compared. Laboratory tests are conducted to investigate the slip behaviour of couplers. A section analysis approach based on equivalent stiffness model is proposed to account for the effects of couplers, and formulations of crack width calculation are explored for use in structural design.

Idaho National Laboratory Cultural Resource Monitoring Report for 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Julie B.

2013-10-01

This report describes the cultural resource monitoring activities of the Idaho National Laboratory’s (INL) Cultural Resource Management (CRM) Office during 2013. Throughout the year, thirty-eight cultural resource localities were revisited including: two locations with Native American human remains, one of which is also a cave; fourteen additional caves; seven prehistoric archaeological sites ; four historic archaeological sites; one historic trail; one nuclear resource (Experimental Breeder Reactor-I, a designated National Historic Landmark); and nine historic structures located at the Central Facilities Area. Of the monitored resources, thirty-three were routinely monitored, and five were monitored to assess project compliance with cultural resourcemore » recommendations along with the effects of ongoing project activities. On six occasions, ground disturbing activities within the boundaries of the Power Burst Facility/Critical Infrastructure Test Range Complex (PBF/CITRC) were observed by INL CRM staff prepared to respond to any additional finds of Native American human remains. In addition, two resources were visited more than once as part of the routine monitoring schedule or to monitor for additional damage. Throughout the year, most of the cultural resources monitored had no visual adverse changes resulting in Type 1determinations. However, Type 2 impacts were noted at eight sites, indicating that although impacts were noted or that a project was operating outside of culturally cleared limitations, cultural resources retained integrity and noted impacts did not threaten National Register eligibility. No new Type 3 or any Type 4 impacts that adversely impacted cultural resources and threatened National Register eligibility were observed at cultural resources monitored in 2013.« less

The NASA Lewis Research Center: An Economic Impact Study

NASA Technical Reports Server (NTRS)

Austrian, Ziona

1996-01-01

The NASA Lewis Research Center (LeRC), established in 1941, is one of ten NASA research centers in the country. It is situated on 350 acres of land in Cuyahoga County and occupies more than 140 buildings and over 500 specialized research and test facilities. Most of LeRC's facilities are located in the City of Cleveland; some are located within the boundaries of the cities of Fairview Park and Brookpark. LeRC is a lead center for NASA's research, technology, and development in the areas of aeropropulsion and selected space applications. It is a center of excellence for turbomachinery, microgravity fluid and combustion research, and commercial communication. The base research and technology disciplines which serve both aeronautics and space areas include materials and structures, instrumentation and controls, fluid physics, electronics, and computational fluid dynamics. This study investigates LeRC's economic impact on Northeast Ohio's economy. It was conducted by The Urban Center's Economic Development Program in Cleveland State University's Levin College of Urban Affairs. The study measures LeRC's direct impact on the local economy in terms of jobs, output, payroll, and taxes, as well as the indirect impact of these economic activities when they 'ripple' throughout the economy. To fully explain LeRC's overall impact on the region, its contributions in the areas of technology transfer and education are also examined. The study uses a highly credible and widely accepted research methodology. First, regional economic multipliers based on input-output models were used to estimate the effect of LERC spending on the Northeast Ohio economy. Second, the economic models were complemented by interviews with industrial, civic, and university leaders to qualitatively assess LeRC's impact in the areas of technology transfer and education.

Geophysical and hydrogeological characterisation of the impacts of on-site wastewater treatment discharge to groundwater in a poorly productive bedrock aquifer.

PubMed

Donohue, Shane; McCarthy, Valerie; Rafferty, Patrick; Orr, Alison; Flynn, Raymond

2015-08-01

Contaminants discharging from on-site wastewater treatment systems (OSWTSs) can impact groundwater quality, threatening human health and surface water ecosystems. Risk of negative impacts becomes elevated in areas of extreme vulnerability with high water tables, where thin unsaturated intervals limit vadose zone attenuation. A combined geophysical/hydrogeological investigation into the effects of an OSWTS, located over a poorly productive aquifer (PPA) with thin subsoil cover, aimed to characterise effluent impacts on groundwater. Groundwater, sampled from piezometers down-gradient of the OSWTS percolation area displayed spatially erratic, yet temporally consistent, contaminant distributions. Electrical resistivity tomography identified an area of gross groundwater contamination close to the percolation area and, when combined with seismic refraction and water quality data, indicated that infiltrating effluent reaching the water table discharged to a deeper more permeable zone of weathered shale resting on more competent bedrock. Subsurface structure, defined by geophysics, indicated that elevated chemical and microbiological contaminant levels encountered in groundwater samples collected from piezometers, down-gradient of sampling points with lower contaminant levels, corresponded to those locations where piezometers were screened close to the weathered shale/competent rock interface; those immediately up-gradient were too shallow to intercept this interval, and thus the more impacted zone of the contaminant plume. Intermittent occurrence of faecal indicator bacteria more than 100m down gradient of the percolation area suggested relatively short travel times. Study findings highlight the utility of geophysics as part of multidisciplinary investigations for OSWTS contaminant plume characterisation, while also demonstrating the capacity of effluent discharging to PPAs to impact groundwater quality at distance. Comparable geophysical responses observed in similar settings across Ireland suggest the phenomena observed in this study are more widespread than previously suspected. Copyright © 2015 Elsevier B.V. All rights reserved.

Damage Detection Sensor System for Aerospace and Multiple Applications

NASA Technical Reports Server (NTRS)

Williams, Martha; Lewis, Mark; Gibson, Tracy L.; Lane, John; Medelius, Pedro

2017-01-01

NASA has identified structural health monitoring and damage detection and verification as critical needs in multiple technology roadmaps. The sensor systems can be customized for detecting location, damage size, and depth, with velocity options and can be designed for particular environments for monitoring of impact or physical damage to a structure. The damage detection system has been successfully demonstrated in a harsh environment and remote integration tested over 1000 miles apart. Multiple applications includes: Spacecraft and Aircraft; Inflatable, Deployable and Expandable Structures; Space Debris Monitoring; Space Habitats; Military Shelters; Solar Arrays, Smart Garments and Wearables, Extravehicular activity (EVA) suits; Critical Hardware Enclosures; Embedded Composite Structures; and Flexible Hybrid Printed Electronics and Systems. For better implementation and infusion into more flexible architectures, important and improved designs in advancing embedded software and GUI interface, and increasing flexibility, modularity, and configurable capabilities of the system are currently being carried out.

Optimization design and analysis of the pavement planer scraper structure

NASA Astrophysics Data System (ADS)

Fang, Yuanbin; Sha, Hongwei; Yuan, Dajun; Xie, Xiaobing; Yang, Shibo

2018-03-01

By LS-DYNA, it establishes the finite element model of road milling machine scraper, and analyses the dynamic simulation. Through the optimization of the scraper structure and scraper angle, obtain the optimal structure of milling machine scraper. At the same time, the simulation results are verified. The results show that the scraper structure is improved that cemented carbide is located in the front part of the scraper substrate. Compared with the working resistance before improvement, it tends to be gentle and the peak value is smaller. The cutting front angle and the cutting back angle are optimized. The cutting front angle is 6 degrees and the cutting back angle is 9 degrees. The resultant of forces which contains the working resistance and the impact force is the least. It proves accuracy of the simulation results and provides guidance for further optimization work.

Minimizing coal terminal marine structure costs. A case history: Plaquemines Parish terminal. [Dock and piles design to absorb and distribute impact and longitudinal forces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pardon, D.V.; Faeth, M.T.; Curth, O.

1981-01-01

At International Marine Terminals' Plaquemines Parish Terminal, design optimization was accomplished by optimizing the dock pile bent spacing and designing the superstructure to distribute berthing impact forces and bollard pulls over a large number of pile bents. Also, by resisting all longitudinal forces acting on the dock at a single location near the center of the structure, the number of longitudinal batter piles was minimized and the need for costly expansion joints was eliminated. Computer techniques were utilized to analyze and optimize the design of the new dock. Pile driving procedures were evaluated utilizing a wave equation technique. Tripod dolphinsmore » with a resilient fender system were provided. The resilent fender system, a combination of rubber shear type and wing type fenders, adds only a small percentage to the total cost of the dolphins but greatly increases their energy absorption capability.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shao, Shuai; Wang, Jian

In this work, using the Cu–Ni (111) semi-coherent interface as a model system, we combine atomistic simulations and defect theory to reveal the relaxation mechanisms, structure, and properties of semi-coherent interfaces. By calculating the generalized stacking fault energy (GSFE) profile of the interface, two stable structures and a high-energy structure are located. During the relaxation, the regions that possess the stable structures expand and develop into coherent regions; the regions with high-energy structure shrink into the intersection of misfit dislocations (nodes). This process reduces the interface excess potential energy but increases the core energy of the misfit dislocations and nodes.more » The core width is dependent on the GSFE of the interface. The high-energy structure relaxes by relative rotation and dilatation between the crystals. The relative rotation is responsible for the spiral pattern at nodes. The relative dilatation is responsible for the creation of free volume at nodes, which facilitates the nodes’ structural transformation. Several node structures have been observed and analyzed. In conclusion, the various structures have significant impact on the plastic deformation in terms of lattice dislocation nucleation, as well as the point defect formation energies.« less

Broad-area detection of structural irregularities in composites using fibre Bragg gratings

NASA Astrophysics Data System (ADS)

Davis, Claire E.; Norman, Patrick; Moss, Scott; Ratcliffe, Colin; Crane, Roger

2010-04-01

The Structural Irregularity and Damage Evaluation Routine (SIDER) is a broadband vibration-based technique that uses features in complex curvature operating shapes to locate damage and other areas with structural stiffness variations. It is designed for the inspection of large-scale composite structures not amenable to more conventional inspection methods. The current SIDER methodology relies on impact excitation at a series of grid points on the structure and records the response using a small number of accelerometers to determine the operational curvature shapes. This paper reports on a modification to the SIDER technique whereby the acceleration measurements are replaced with in-plane strain measurements using Fibre Bragg Gratings (FBGs). One of the major challenges associated with using Bragg gratings for this type of response measurement is that the strains induced by structural vibrations tend to be low, particularly at higher frequencies. This paper also reports on the development of an intensity-based, swept wavelength interrogation system to facilitate these measurements. The modified SIDER system was evaluated on an E-glass/vinyl ester composite test beam containing a machined notch. The measurements accurately detected the presence and location of the notch. The distributive capacity of FBGs means that these sensors have the potential to replace the excitation grid with a measurement grid, allowing for single point or environmental excitation. The spatially separated measurements of strain can be used to provide the curvature shapes directly. This change in approach could potentially transition SIDER from an interval-based, broad-area inspection tool to an in-service structural health monitoring system.

14 CFR 420.27 - Launch site location review-information requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... corridor, and each impact range and impact dispersion area for each launch point; (b) Each launch vehicle... the analysis; (f) Each populated area located within a flight corridor or impact dispersion area; (g) The estimated casualty expectancy calculated for each populated area within a flight corridor or...

14 CFR 420.27 - Launch site location review-information requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... corridor, and each impact range and impact dispersion area for each launch point; (b) Each launch vehicle... the analysis; (f) Each populated area located within a flight corridor or impact dispersion area; (g) The estimated casualty expectancy calculated for each populated area within a flight corridor or...

14 CFR 420.27 - Launch site location review-information requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... corridor, and each impact range and impact dispersion area for each launch point; (b) Each launch vehicle... the analysis; (f) Each populated area located within a flight corridor or impact dispersion area; (g) The estimated casualty expectancy calculated for each populated area within a flight corridor or...

14 CFR 420.27 - Launch site location review-information requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... corridor, and each impact range and impact dispersion area for each launch point; (b) Each launch vehicle... the analysis; (f) Each populated area located within a flight corridor or impact dispersion area; (g) The estimated casualty expectancy calculated for each populated area within a flight corridor or...

14 CFR 35.36 - Bird impact.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Bird impact. 35.36 Section 35.36... STANDARDS: PROPELLERS Tests and Inspections § 35.36 Bird impact. The applicant must demonstrate, by tests or... 4-pound bird at the critical location(s) and critical flight condition(s) of a typical installation...

14 CFR 35.36 - Bird impact.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Bird impact. 35.36 Section 35.36... STANDARDS: PROPELLERS Tests and Inspections § 35.36 Bird impact. The applicant must demonstrate, by tests or... 4-pound bird at the critical location(s) and critical flight condition(s) of a typical installation...

Impact melt-bearing breccias of the Mistastin Lake impact structure: A unique planetary analogue for ground-truthing proximal ejecta emplacement

NASA Astrophysics Data System (ADS)

Mader, M. M.; Osinski, G. R.

2013-12-01

Impact craters are the dominant geological landform on rocky planetary surfaces; however, relationships between specific craters and their ejecta are typically poorly constrained. With limited planetary samples, scientists look to terrestrial craters as analogues. Impact ejecta is defined here as any target material, regardless of its physical state, that is transported beyond the rim of the transient cavity [1]. The original transient cavity reaches its maximum size during the excavation stage of crater formation, before rim collapse begins in the modification stage [2]. In complex craters, during the modification stage, rocks around the periphery of the bowl-shaped transient crater collapse downward and inward to form a series of terraces along the outer margin of the crater structure [3]. Proximal impact ejecta, can therefore be found on the terraces of the modified rim of a complex crater, interior to the final crater rim [1]. Although typically poorly preserved on Earth due to post-impact erosional processes, impact ejecta have been identified in the terraced rim region of the Mistastin Lake impact structure, located in northern Labrador, Canada (55°53'N; 63°18'W) [4]. The Mistastin Lake impact structure is an intermediate-size, complex crater (28 km apparent crater diameter) formed by a meteorite impact ~36 Ma in crystalline target rocks. The original crater has been differentially eroded; however, a terraced rim and distinct central uplift are still observed [5]. The inner portion of the structure is covered by the Mistastin Lake and the surrounding area is locally covered by soil/glacial deposits and vegetation. Locally, allochthonous impactites overlying fractured target rocks are exposed along the lakeshore and along banks of radially cutting streams. They define a consistent stratigraphy, including, from bottom to top: monomict, lithic breccias, allochthonous polymict lithic breccias, and allochthonous impact melt rocks. Mistastin impact breccias range in matrix content, melt-fragment concentration, and contact relationships with adjacent impactites. Initial findings suggest differing origins for impact melt-bearing breccias from a single impact event. Three examples are highlighted: 1) Impact melt-bearing breccias, on an inner terrace, formed in boundary zones where hot impact melt flowed over cooler, ballistically emplaced polymict impact breccias. 2) Locally, a dyke of impact melt-bearing breccia suggests that this unit originated as hot lithic flow that moved laterally along the ground and then intruded as a fracture fill into target rocks. 3) A m-scale lens of melt-bearing breccia within the middle of a thick, 80m impact melt rock unit situated on an inner terrace, suggests that this lens may have originated from the crater floor and been incorporated into the melt pond during emplacement (i.e. movement of the melt from the crater floor to terrace shelf). In summary, the Mistastin Lake impact structure displays a multiple layered ejecta sequence that is consistent with, and requires, a multi-stage ejecta emplacement model as proposed by [1]. References: [1] Osinski et al. (2011) EPSL (310:167-181. [2] Melosh (1989) Oxford Univ. 245 pp. [3] French B. M. (1998) LPI Contribution 954,120pp. [4] Mader et al. (2011) 42nd LPSC, No.1608. [5] Mader et al. (2013) 43rd LPSC, No. 2517.

Effects of Pre-existing Structures on the Seismicity of the Charlevoix Seismic Zone

NASA Astrophysics Data System (ADS)

Fadugba, O. I.; Choi, E.; Powell, C. A.

2017-12-01

The Charlevoix Seismic Zone (CSZ) occurs along the early Paleozoic St. Lawrence rift zone in southeastern Quebec at the location of a major Devonian impact crater. The crater superimposed major, steeply dipping basement faults trending N35°E. Many earthquakes are recorded each year in the CSZ and are concentrated within and beneath the impact crater. Some large-magnitude earthquakes associated with the rift faults occurred outside the crater. The primary goal of this research is to investigate combined effects of the pre-existing structures and regional stresses on earthquake activity in the CSZ. We set up some models using PyLith, an open-source finite-element code for simulations of crustal deformation. Our models will be compared with those of Baird et al. (2010), which took a different numerical approach for the same purpose of relating the regional structures, stresses, and seismicity. Adopting the results from recent hypocenter relocation study, we will modify the locations and dips of the rift faults and assess the effect of the new fault geometries on stress distributions. Finally, we will discuss whether modeled stress distributions can explain the seismicity distribution in the CSZ and published focal mechanism solutions. As a part of our efforts to enhance the reproducibility of these types of complex geodynamic models, selected models in this study will be made available in the form of sharable and reproducible packages. Such packaging is enabled by GeoTrust, an EarthCube-funded project that aims to automate the creation of a self-contained metadata package that provides a complete description of all data elements associated with a computational experiment.

Blind tests of methods for InSight Mars mission: Open scientific challenge

NASA Astrophysics Data System (ADS)

Clinton, John; Ceylan, Savas; Giardini, Domenico; Khan, Amir; van Driel, Martin; Böse, Maren; Euchner, Fabian; Garcia, Raphael F.; Drilleau, Mélanie; Lognonné, Philippe; Panning, Mark; Banerdt, Bruce

2017-04-01

The Marsquake Service (MQS) will be the ground segment service within the InSight mission to Mars, which will deploy a single seismic station on Elysium Planitia in November 2018. The main tasks of the MQS are the identification and characterisation of seismicity, and managing the Martian seismic event catalogue. In advance of the mission, we have developed a series of single station event location methods that rely on a priori 1D and 3D structural models. In coordination with the Mars Structural Service, we expect to use iterative inversion techniques to revise these structural models and event locations. In order to seek methodological advancements and test our current approaches, we have designed a blind test case using Martian synthetics combined with realistic noise models for the Martian surface. We invite all scientific parties that are interested in single station approaches and in exploring the Martian time-series to participate and contribute to our blind test. We anticipate the test will can improve currently developed location and structural inversion techniques, and also allow us explore new single station techniques for moment tensor and magnitude determination. The waveforms for our test case are computed employing AxiSEM and Instaseis for a randomly selected 1D background model and event catalogue that is statistically consistent with our current expectation of Martian seismicity. Realistic seismic surface noise is superimposed to generate a continuous time-series spanning 6 months. The event catalog includes impacts as well as Martian quakes. The temporal distribution of the seismicity in the timeseries, as well as the true structural model, are not be known to any participating parties including MQS till the end of competition. We provide our internal tools such as event location codes, suite of background models, seismic phase travel times, in order to support researchers who are willing to use/improve our current methods. Following the deadline of our blind test in late 2017, we plan to combine all outcomes in an article with all participants as co-authors.

Physiological Implications of Myocardial Scar Structure

PubMed Central

Richardson, WJ; Clarke, SA; Quinn, TA; Holmes, JW

2016-01-01

Once myocardium dies during a heart attack, it is replaced by scar tissue over the course of several weeks. The size, location, composition, structure and mechanical properties of the healing scar are all critical determinants of the fate of patients who survive the initial infarction. While the central importance of scar structure in determining pump function and remodeling has long been recognized, it has proven remarkably difficult to design therapies that improve heart function or limit remodeling by modifying scar structure. Many exciting new therapies are under development, but predicting their long-term effects requires a detailed understanding of how infarct scar forms, how its properties impact left ventricular function and remodeling, and how changes in scar structure and properties feed back to affect not only heart mechanics but also electrical conduction, reflex hemodynamic compensations, and the ongoing process of scar formation itself. In this article, we outline the scar formation process following an MI, discuss interpretation of standard measures of heart function in the setting of a healing infarct, then present implications of infarct scar geometry and structure for both mechanical and electrical function of the heart and summarize experiences to date with therapeutic interventions that aim to modify scar geometry and structure. One important conclusion that emerges from the studies reviewed here is that computational modeling is an essential tool for integrating the wealth of information required to understand this complex system and predict the impact of novel therapies on scar healing, heart function, and remodeling following myocardial infarction. PMID:26426470

Global Volcanism on Mercury at About 3.8 Ga

NASA Astrophysics Data System (ADS)

Byrne, P. K.; Ostrach, L. R.; Denevi, B. W.; Head, J. W., III; Hauck, S. A., II; Murchie, S. L.; Solomon, S. C.

2014-12-01

Smooth plains occupy c. 27% of the surface of Mercury. Embayment relations, spectral contrast with surroundings, and morphologic characteristics indicate that the majority of these plains are volcanic. The largest deposits are located in Mercury's northern hemisphere and include the extensive northern plains (NP) and the Caloris interior and exterior plains (with the latter likely including basin material). Both the NP and Caloris deposits are, within statistical error, the same age (~3.8-3.9 Ga). To test whether this age reflects a period of global volcanism on Mercury, we determined crater size-frequency distributions for four smooth plains units in the planet's southern hemisphere interpreted to be volcanic. Two deposits are situated within the Beethoven and Tolstoj impact basins; two are located close to the Debussy and the Alver and Disney basins, respectively. Each deposit hosts two populations of craters, one that postdates plains emplacement and one that consists of partially to nearly filled craters that predate the plains. This latter population indicates that some time elapsed between formation of the underlying basement and plains volcanism, though we cannot statistically resolve this interval at any of the four sites. Nonetheless, we find that the age given by the superposed crater population in each case is ~3.8 Ga, and crater density values are consistent with those for the NP and Caloris plains. This finding supports a global phase of volcanism near the end of the late heavy bombardment of Mercury and may indicate a period of widespread partial melting of Mercury's mantle. Notably, superposition relations between smooth plains, degraded impact structures, and contractional landforms suggest that by this time interior cooling had already placed Mercury's lithosphere in horizontal compression, tending to inhibit voluminous dike-fed volcanism such as that inferred responsible for the NP. Most smooth plains units, including the Caloris plains and our four study sites, are spatially associated with impact structures; even the NP lie in a regional depression that may be impact-related. Because impacts remove overburden, deposit subsurface heat, and relax pre-existing stress, basins and craters may represent preferential sites for volcanic resurfacing on a globally contracting planet.

A Survey of Research Performed at NASA Langley Research Center's Impact Dynamics Research Facility

NASA Technical Reports Server (NTRS)

Jackson, K. E.; Fasanella, E. L.

2003-01-01

The Impact Dynamics Research Facility (IDRF) is a 240-ft-high gantry structure located at NASA Langley Research Center in Hampton, Virginia. The facility was originally built in 1963 as a lunar landing simulator, allowing the Apollo astronauts to practice lunar landings under realistic conditions. The IDRF was designated a National Historic Landmark in 1985 based on its significant contributions to the Apollo Program. In 1972, the facility was converted to a full-scale crash test facility for light aircraft and rotorcraft. Since that time, the IDRF has been used to perform a wide variety of impact tests on full-scale aircraft and structural components in support of the General Aviation (GA) aircraft industry, the US Department of Defense, the rotorcraft industry, and NASA in-house aeronautics and space research programs. The objective of this paper is to describe most of the major full-scale crash test programs that were performed at this unique, world-class facility since 1974. The past research is divided into six sub-topics: the civil GA aircraft test program, transport aircraft test program, military test programs, space test programs, basic research, and crash modeling and simulation.

The Ability of American Football Helmets to Manage Linear Acceleration With Repeated High-Energy Impacts.

PubMed

Cournoyer, Janie; Post, Andrew; Rousseau, Philippe; Hoshizaki, Blaine

2016-03-01

Football players can receive up to 1400 head impacts per season, averaging 6.3 impacts per practice and 14.3 impacts per game. A decrease in the capacity of a helmet to manage linear acceleration with multiple impacts could increase the risk of traumatic brain injury. To investigate the ability of football helmets to manage linear acceleration with multiple high-energy impacts. Descriptive laboratory study. Laboratory. We collected linear-acceleration data for 100 impacts at 6 locations on 4 helmets of different models currently used in football. Impacts 11 to 20 were compared with impacts 91 to 100 for each of the 6 locations. Linear acceleration was greater after multiple impacts (91-100) than after the first few impacts (11-20) for the front, front-boss, rear, and top locations. However, these differences are not clinically relevant as they do not affect the risk for head injury. American football helmet performance deteriorated with multiple impacts, but this is unlikely to be a factor in head-injury causation during a game or over a season.

[Spectral analysis of fiber bragg grating modulated by double long period grating and its application in smart structure monitoring].

PubMed

Lu, Ji-Yun; Liang, Da-Kai; Zhang, Xiao-Li; Zhu, Zhu

2009-12-01

Spectrum of fiber bragg grating (FBG) sensor modulated by double long period grating (LPFG) is proposed in the paper. Double LPFG consists of two LPFGS whose center wavelengths are the same and reflection spectrum of FBG sensor is located in linear range of double LPFG transmission spectrum. Based on spectral analysis of FBG and double LPFG, reflection spectrum of FBG modulated by double LPFG is obtained and studied by use of band-hider filter characteristics for double LPFG. An FBG sensor is attached on the surface of thin steel beam, which is strained by bending, and the center wavelength of FBG sensor will shift. The spectral peak of FBG sensor modulated by double LPFG is changed correspondingly, and the spectral change will lead to variation in exit light intensity from double LPFG. Experiment demonstrates that the relation of filtering light intensity from double LPFG monitored by optical power meter to center wavelength change of FBG sensor is linear and the minimum strain of material (steel beam) detected by the modulation and demodulation system is 1.05 microepsilon. This solution is used in impact monitoring of optical fibre smart structure, and FBG sensor is applied for impulse response signal monitoring induced by low-velocity impact, when impact pendulum is loaded to carbon fiber-reinforced plastics (CFP). The acquired impact response signal and fast Fourier transform of the signal detected by FBG sensor agree with the measurement results of eddy current displacement meter attached to the FBG sensor. From the results, the present method using FBG sensor is found to be effective for monitoring the impact. The research provides a practical reference in dynamic monitoring of optical fiber smart structure field.

Detection, Localization and Quantification of Impact Events on a Stiffened Composite Panel with Embedded Fiber Bragg Grating Sensor Networks

PubMed Central

Lamberti, Alfredo; Luyckx, Geert; Van Paepegem, Wim; Rezayat, Ali; Vanlanduit, Steve

2017-01-01

Nowadays, it is possible to manufacture smart composite materials with embedded fiber optic sensors. These sensors can be exploited during the composites’ operating life to identify occurring damages such as delaminations. For composite materials adopted in the aviation and wind energy sector, delaminations are most often caused by impacts with external objects. The detection, localization and quantification of such impacts are therefore crucial for the prevention of catastrophic events. In this paper, we demonstrate the feasibility to perform impact identification in smart composite structures with embedded fiber optic sensors. For our analyses, we manufactured a carbon fiber reinforced plate in which we embedded a distributed network of fiber Bragg grating (FBG) sensors. We impacted the plate with a modal hammer and we identified the impacts by processing the FBG data with an improved fast phase correlation (FPC) algorithm in combination with a variable selective least squares (VS-LS) inverse solver approach. A total of 164 impacts distributed on 41 possible impact locations were analyzed. We compared our methodology with the traditional P-Inv based approach. In terms of impact localization, our methodology performed better in 70.7% of the cases. An improvement on the impact time domain reconstruction was achieved in 95.1% of the cases. PMID:28368319

Detection, Localization and Quantification of Impact Events on a Stiffened Composite Panel with Embedded Fiber Bragg Grating Sensor Networks.

PubMed

Lamberti, Alfredo; Luyckx, Geert; Van Paepegem, Wim; Rezayat, Ali; Vanlanduit, Steve

2017-04-01

Nowadays, it is possible to manufacture smart composite materials with embedded fiber optic sensors. These sensors can be exploited during the composites' operating life to identify occurring damages such as delaminations. For composite materials adopted in the aviation and wind energy sector, delaminations are most often caused by impacts with external objects. The detection, localization and quantification of such impacts are therefore crucial for the prevention of catastrophic events. In this paper, we demonstrate the feasibility to perform impact identification in smart composite structures with embedded fiber optic sensors. For our analyses, we manufactured a carbon fiber reinforced plate in which we embedded a distributed network of fiber Bragg grating (FBG) sensors. We impacted the plate with a modal hammer and we identified the impacts by processing the FBG data with an improved fast phase correlation (FPC) algorithm in combination with a variable selective least squares (VS-LS) inverse solver approach. A total of 164 impacts distributed on 41 possible impact locations were analyzed. We compared our methodology with the traditional P-Inv based approach. In terms of impact localization, our methodology performed better in 70.7% of the cases. An improvement on the impact time domain reconstruction was achieved in 95 . 1 % of the cases.

Association of anatase (TiO2) and microbes: Unusual fossilization effect or a potential biosignature?

USGS Publications Warehouse

Glamoclija, M.; Steele, A.; Fries, M.; Schieber, J.; Voytek, M.A.; Cockell, C.S.

2009-01-01

We combined microbial paleontology and molecular biology methods to study the Eyreville B drill core from the 35.3-Ma-old Chesapeake Bay impact structure, Virginia, USA. The investigated sample is a pyrite vein collected from the 1353.81- 1353.89 m depth interval, located within a section of biotite granite. The granite is a pre-impact rock that was disrupted by the impact event. A search for inorganic (mineral) biosignatures revealed the presence of micron-size rod morphologies of anatase (TiO2) embedded in chlorite coatings on pyrite grains. Neither the Acridine Orange microbial probe nor deoxyribonucleic acid (DNA) extraction followed by polymerase chain reaction (PCR) amplifi cation showed the presence of DNA or ribonucleic acid (RNA) at the location of anatase rods, implying the absence of viable cells in the investigated area. A Nile Red microbial probe revealed the presence of lipids in the rods. Because most of the lipids are resistant over geologic time spans, they are good biomarkers, and they are an indicator of biogenicity for these possibly 35-Ma-old microbial fossils. The mineral assemblage suggests that rod morphologies are associated with low-temperature (<100 ??C) hydrothermal alteration that involved aqueous fluids. The temporal constraints on the anatase fossils are still uncertain because pre-impact alteration of the granite and postimpact heating may have provided identical conditions for anatase precipitation and microbial preservation. ?? 2009 The Geological Society of America.

Distribution and geologic history of materials excavated by the lunar crater Bullialdus

NASA Technical Reports Server (NTRS)

Tompkins, Stefanie; Pieters, Carle M.; Mustard, John F.

1993-01-01

The crater Bullialdus is a 61 km, Eratosthenian-age impact crater located on the western edge of Mare Nubium. Previous analysis of the spatial distribution of materials in the area using nine telescopic near-infrared spectra suggested a possible three-layer structure prior to the impact event: two shallow gabbroic layers and one deeper noritic layer (from a potential depth of 5.5 km). The initial interpretation of this stratigraphy was that Bullialdus may have tapped a layered mafic pluton, such as have been invoked to explain the existence of Mg-suite rocks. High-spatial resolution CCD images of Bullialdus were analyzed to better map the spatial distribution of the observed lithologies, and to assess the plausibility of the pluton interpretation.

The geomorphology of Ceres

USGS Publications Warehouse

Buczkowski, D.L.; Schmidt, B.E.; Williams, D.A.; Mest, S.C.; Scully, J.E.C.; Ermakov, A.; Preusker, F.; Schenk, P.; Otto, K. A.; Hiesinger, H.; O'Brien, D.; Marchi, S.; Sizemore, H.G.; Hughson, K.; Chilton, H.; Bland, M.; Byrne, S.; Schorghofer, N.; Platz, T.; Jaumann, R.; Roatsch, T.; Sykes, M. V.; Nathues, A.; De Sanctis, M.C.; Raymond, C.A.; Russell, C.T.

2016-01-01

Analysis of Dawn spacecraft Framing Camera image data allows evaluation of the topography and geomorphology of features on the surface of Ceres. The dwarf planet is dominated by numerous craters, but other features are also common. Linear structures include both those associated with impact craters and those that do not appear to have any correlation to an impact event. Abundant lobate flows are identified, and numerous domical features are found at a range of scales. Features suggestive of near-surface ice, cryomagmatism, and cryovolcanism have been identified. Although spectroscopic analysis has currently detected surface water ice at only one location on Ceres, the identification of these potentially ice-related features suggests that there may be at least some ice in localized regions in the crust.

Hazard Assessment of Glacial Lake Outburst Flood and Potential of ICTs for Coping: A Case of Eastern Himalaya of Nepal

NASA Astrophysics Data System (ADS)

Bhattarai, D. R.

2015-12-01

Retreat of glaciers and formation of glacial lakes in Nepal Himalaya have been reported to be related with the temperature rise in the region. Glacier Lake Outburst Floods (GLOF) are the growing climate induced hazards in the Himalaya. GLOF has increased the vulnerability of community and fragile ecosystem in the mountain valleys. This study has analyzed the potential impacts from GLOF in the highland of eastern Nepal and the potential role of Information Communication Technologies (ICT) to cope with such impacts. I analyzed the trend of climatic pattern (temperature and precipitation) of the Eastern Himalaya Region of Nepal available from the Department of Hydrology and Meteorology, Government of Nepal, and prepared the latest location map of the glacial lakes using google earth and ArcGIS applications in the highland of the Kanchanjungha Conservation Area of the region. Tiptala glacial lake, located at an elevation of 4950 m, within the conservation area, was selected for the GLOF hazard assessment. I used semi-structured questionnaire survey and key informants' interviews in the community in order to assess the potential hazard of GLOF. With the varying sizes, 46 glacial lakes were located in the region, which covers over 2.57 sq. km in total. Though the larger portion of the downstream area of the Tiptala glacial lake fall in the remote location away from major residential area, few villages, major pasture lands for Yaks, foot trails, and several bridges across the Tamor River below the lake are in risk of GLOF. Poor access due to extreme geographical remoteness and capacity to afford the modern technologies in the community are the major limiting factor to the knowledge and information about the climate change and related impacts. Modern ICTs has high potential to reduce the risk of climate related hazards in the remote area by information dissemination and awareness.

Overview on urban and peri-urban agriculture: definition, impact on human health, constraints and policy issues.

PubMed

Kang'ethe, E K; Grace, D; Randolph, T F

2007-11-01

To collate and synthesize current knowledge of components of urban agriculture (UA) with a thematic emphasis on human health impact and a geographic emphasis on East Africa. Data management followed a structured approach in which key issues were first identified and then studies selected through literature search and personal communication. Evidence-based principles. Urban agriculture is an important source of food security for urban dwellers in East Africa. Descriptors of UA are location, areas, activities, scale, products, destinations, stakeholders and motivation. Many zoonotic and food-borne diseases have been associated with UA but evidence on human health impact and management is lacking. Major constraints to UA are illegality and lack of access to input and market; policy options have been developed for overcoming these. Urban agriculture is an important activity and likely to remain so. Both positive and negative human health impacts are potentially important but more research is needed to understand these and set appropriate policy and support levels.

Impacts on the Hubble Space Telescope Wide Field and Planetary Camera 2: Microanalysis and Recognition of Micrometeoroid Compositions

NASA Technical Reports Server (NTRS)

Kearsley, A. T.; Ross, D. K.; Anz-Meador, P.; Liou, J. C.; Opiela, J.; Grime, G. W.; Webb, R. P.; Jeynes, C.; Palitsin, V. V.; Colaux, J. L.;

Calibrated Multiple Event Relocations of the Central and Eastern United States

NASA Astrophysics Data System (ADS)

Yeck, W. L.; Benz, H.; McNamara, D. E.; Bergman, E.; Herrmann, R. B.; Myers, S. C.

2015-12-01

Earthquake locations are a first-order observable which form the basis of a wide range of seismic analyses. Currently, the ANSS catalog primarily contains published single-event earthquake locations that rely on assumed 1D velocity models. Increasing the accuracy of cataloged earthquake hypocenter locations and origin times and constraining their associated errors can improve our understanding of Earth structure and have a fundamental impact on subsequent seismic studies. Multiple-event relocation algorithms often increase the precision of relative earthquake hypocenters but are hindered by their limited ability to provide realistic location uncertainties for individual earthquakes. Recently, a Bayesian approach to the multiple event relocation problem has proven to have many benefits including the ability to: (1) handle large data sets; (2) easily incorporate a priori hypocenter information; (3) model phase assignment errors; and, (4) correct for errors in the assumed travel time model. In this study we employ bayseloc [Myers et al., 2007, 2009] to relocate earthquakes in the Central and Eastern United States from 1964-present. We relocate ~11,000 earthquakes with a dataset of ~439,000 arrival time observations. Our dataset includes arrival-time observations from the ANSS catalog supplemented with arrival-time data from the Reviewed ISC Bulletin (prior to 1981), targeted local studies, and arrival-time data from the TA Array. One significant benefit of the bayesloc algorithm is its ability to incorporate a priori constraints on the probability distributions of specific earthquake locations parameters. To constrain the inversion, we use high-quality calibrated earthquake locations from local studies, including studies from: Raton Basin, Colorado; Mineral, Virginia; Guy, Arkansas; Cheneville, Quebec; Oklahoma; and Mt. Carmel, Illinois. We also add depth constraints to 232 earthquakes from regional moment tensors. Finally, we add constraints from four historic (1964-1973) ground truth events from a verification database. We (1) evaluate our ability to improve our location estimations, (2) use improved locations to evaluate Earth structure in seismically active regions, and (3) examine improvements to the estimated locations of historic large magnitude earthquakes.

Wild Duck Cluster

NASA Technical Reports Server (NTRS)

2005-01-01

On April 7, 2005, the Deep Impact spacecraft's Impactor Target Sensor camera recorded this image of M11, the Wild Duck cluster, a galactic open cluster located 6 thousand light years away. The camera is located on the impactor spacecraft, which will image comet Tempel 1 beginning 22 hours before impact until about 2 seconds before impact. Impact with comet Tempel 1 is planned for July 4, 2005.

Mass movement on Vesta at steep scarps and crater rims

NASA Astrophysics Data System (ADS)

Krohn, K.; Jaumann, R.; Otto, K.; Hoogenboom, T.; Wagner, R.; Buczkowski, D. L.; Garry, B.; Williams, D. A.; Yingst, R. A.; Scully, J.; De Sanctis, M. C.; Kneissl, T.; Schmedemann, N.; Kersten, E.; Stephan, K.; Matz, K.-D.; Pieters, C. M.; Preusker, F.; Roatsch, T.; Schenk, P.; Russell, C. T.; Raymond, C. A.

2014-12-01

The Quadrangles Av-11 and Av-12 on Vesta are located at the northern rim of the giant Rheasilvia south polar impact basin. The primary geologic units in Av-11 and Av-12 include material from the Rheasilvia impact basin formation, smooth material and different types of impact crater structures (such as bimodal craters, dark and bright crater ray material and dark ejecta material). Av-11 and Av-12 exhibit almost the full range of mass wasting features observed on Vesta, such as slump blocks, spur-and-gully morphologies and landslides within craters. Processes of collapse, slope instability and seismically triggered events force material to slump down crater walls or scarps and produce landslides or rotational slump blocks. The spur-and-gully morphology that is known to form on Mars is also observed on Vesta; however, on Vesta this morphology formed under dry conditions.

Mass Movement on Vesta at Steep Scarps and Crater Rims

NASA Technical Reports Server (NTRS)

Krohn, K.; Jaumann, R.; Otto, K.; Hoogenboom, T.; Wagner, R.; Buczkowski, D. L.; Garry, B.; Williams, D. A.; Yingst, R. A.; Scully, J.;

A non-contacting approach for full field dynamic strain monitoring of rotating structures using the photogrammetry, finite element, and modal expansion techniques

NASA Astrophysics Data System (ADS)

Baqersad, Javad

Health monitoring of rotating structures such as wind turbines and helicopter rotors is generally performed using conventional sensors that provide a limited set of data at discrete locations near or on the hub. These sensors usually provide no data on the blades or interior locations where failures may occur. Within this work, an unique expansion algorithm was extended and combined with finite element (FE) modeling and an optical measurement technique to identify the dynamic strain in rotating structures. The merit of the approach is shown by using the approach to predict the dynamic strain on a small non-rotating and rotating wind turbine. A three-bladed wind turbine having 2.3-meter long blades was placed in a semi-built-in boundary condition using a hub, a machining chuck, and a steel block. A finite element model of the three wind turbine blades assembled to the hub was created and used to extract resonant frequencies and mode shapes. The FE model was validated and updated using experimental modal tests. For the non-rotating optical test, the turbine was excited using a sinusoidal excitation, a pluck test, arbitrary impacts on three blades, and random force excitations with a mechanical shaker. The response of the structure to the excitations was measured using three-dimensional point tracking. A pair of high-speed cameras was used to measure the displacement of optical targets on the structure when the blades were vibrating. The measured displacements at discrete locations were expanded and applied to the finite element model of the structure to extract the full-field dynamic strain. The results of the work show an excellent correlation between the strain predicted using the proposed approach and the strain measured with strain-gages for all of the three loading conditions. Similar to the non-rotating case, optical measurements were also preformed on a rotating wind turbine. The point tracking technique measured both rigid body displacement and flexible deformation of the blades at target locations. The measured displacements were expanded and applied to the finite element model of the turbine to extract full-field dynamic strain on the structure. In order to validate the results for the rotating turbine, the predicted strain was compared to strain measured at four locations on the spinning blades using a wireless strain-gage system. The approach used in this work to predict the strain showed higher accuracy than measurements obtainable by using the digital image correlation technique. The new expansion approach is able to extract dynamic strain all over the entire structure, even inside the structure beyond the line of sight of the measurement system. Because the method is based on a non-contacting measurement approach, it can be readily applied to a variety of structures having different boundary and operating conditions, including rotating blades.

Tectonic Structure, Solid Earth and Cryosphere Interactions in the Casey-Davis Region of East Antarctica

NASA Astrophysics Data System (ADS)

Reading, A. M.; King, M. A.; Halpin, J.; Whittaker, J. M.; White, D.; Cook, S.; Staal, T.

2016-12-01

The region of inland East Antarctica between Casey and Davis stations (Wilkes Land to Princess Elizabeth Land) is one of the least investigated parts of the continent with respect to its tectonic and solid Earth structure. This is difficult to estimate because the conjugate margin in plate reconstructions has been lost in the collision between India and Eurasia. The region is also host to some of the greatest uncertainties in Antarctica in glacial-isostatic adjustment observations and models, and where the contribution of heat from underlying rocks is difficult to estimate due to the limited available rock samples. We investigate the solid Earth structure and its interactions with the East Antarctic ice sheet through a new campaign including GPS and seismic instrument deployments, and field measurements to constrain ice retreat history. This presentation provides an overview of the new, multi-year Casey-Davis Glacial Isostatic Adjustment campaign including station locations and deployment progress. The campaign is being supported by Australian Antarctic Division and uses a combination of fixed-wing and helicopter support to access station locations in both coastal locations and the continental interior. A primary long-term objective of the campaign is to remove bias from estimates of East Antarctica's contribution to past and present sea level changes. We also seek to better constrain the geothermal influences on the East Antarctic ice sheet. The GPS determinations of vertical plate motion and the detailed seismic structure await data downloads in future field seasons, however, we are able to present new findings from preliminary studies. We show candidate ancient tectonic reconstructions for this part of East Antarctica and make use of our knowledge of structure of continental regions with a similar evolution to infer the likely structures for the Casey-Davis region. We add these new constraints to the structure currently inferred from a very small number of insitu measurements and sparse remote sensing data and compile the diverse information using a near-comprehensive GIS for the current time. We also outline the interplay between uncertainties on the structure of the crust, lithosphere and upper mantle and the likely impact on glacial-isostatic and geothermal usage of solid Earth information.

Detection of environmental impacts of shrimp farming through multiple lines of evidence.

PubMed

Hatje, Vanessa; de Souza, Manuel M; Ribeiro, Luisa F; Eça, Gilmara F; Barros, Francisco

2016-12-01

In order to evaluate the impact of semi-intensive shrimp farming, comparisons between Control and Impact areas were made based on multiple lines of evidence using an asymmetrical design. Water and sediment samples were collected in four shrimp farms located in Todos os Santos Bay, Bahia, Brazil. Nutrients, trace elements and macrobenthic assemblages were evaluated using uni- and multivariate analyzes. Significant differences were observed between Impact and Control areas for the water column dataset (i.e., ancillary variables, SPM, dissolved nutrients and major and trace elements in SPM), whereas no significant differences were observed for the chemistry of sediments. Macrobenthic assemblages were negatively affected by shrimp farm activities. Impacted sites presented the lowest abundance, richness and different structure of macrofaunal benthic assemblages. Farms clearly produced negative impacts in the Todos os Santos Bay. This conclusion was only possible to be reached through the use of multiple lines of evidence. Chemistry and benthic assemblages data combined produced a better description of the quality and impacts of the evaluated environments. Different conclusions would have been reached if chemistry and ecology results were studied separately vs. together. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mucosal Barrier Injury Laboratory-Confirmed Bloodstream Infections (MBI-LCBI): Descriptive Analysis of Data Reported to National Healthcare Safety Network (NHSN), 2013.

PubMed

Epstein, Lauren; See, Isaac; Edwards, Jonathan R; Magill, Shelley S; Thompson, Nicola D

2016-01-01

OBJECTIVES To determine the impact of mucosal barrier injury laboratory-confirmed bloodstream infections (MBI-LCBIs) on central-line-associated bloodstream infection (CLABSI) rates during the first year of MBI-LCBI reporting to the National Healthcare Safety Network (NHSN) DESIGN Descriptive analysis of 2013 NHSN data SETTING Selected inpatient locations in acute care hospitals METHODS A descriptive analysis of MBI-LCBI cases was performed. CLABSI rates per 1,000 central-line days were calculated with and without the inclusion of MBI-LCBIs in the subset of locations reporting ≥1 MBI-LCBI, and in all locations (regardless of MBI-LCBI reporting) to determine rate differences overall and by location type. RESULTS From 418 locations in 252 acute care hospitals reporting ≥1 MBI-LCBIs, 3,162 CLABSIs were reported; 1,415 (44.7%) met the MBI-LCBI definition. Among these locations, removing MBI-LCBI from the CLABSI rate determination produced the greatest CLABSI rate decreases in oncology (49%) and ward locations (45%). Among all locations reporting CLABSI data, including those reporting no MBI-LCBIs, removing MBI-LCBI reduced rates by 8%. Here, the greatest decrease was in oncology locations (38% decrease); decreases in other locations ranged from 1.2% to 4.2%. CONCLUSIONS An understanding of the potential impact of removing MBI-LCBIs from CLABSI data is needed to accurately interpret CLABSI trends over time and to inform changes to state and federal reporting programs. Whereas the MBI-LCBI definition may have a large impact on CLABSI rates in locations where patients with certain clinical conditions are cared for, the impact of MBI-LCBIs on overall CLABSI rates across inpatient locations appears to be more modest. Infect. Control Hosp. Epidemiol. 2015;37(1):2-7.

Tree Line Structure and Dynamics at the Northern Limit of the Larch Forest: Anabar Plateau, Siberia, Russia

NASA Technical Reports Server (NTRS)

Kharuk, Viacheslav I.; Ranson, Kenneth J.; Im, Sergey T.; Oskorbin, Pavel A.; Dvinskaya, Maria L.; Ovchinnikov, Dmitriy V.

2013-01-01

The goal of the study was to provide an analysis of climate impact before, during, and after the Little Ice Age (LIA) on the larch (Larix gmelinii) tree line at the northern extreme of Siberian forests. Recent decadal climate change impacts on the tree line, regeneration abundance, and age structure were analyzed. The location of the study area was within the forest-tundra ecotone (elevation range 170-450 m) in the Anabar Plateau, northern Siberia. Field studies were conducted along elevational transects. Tree natality/mortality and radial increment were determined based on dendrochronology analyses. Tree morphology, number of living and subfossil trees, regeneration abundance, and age structure were studied. Locations of pre-LIA, LIA, and post-LIA tree lines and refugia boundaries were established. Long-term climate variables and drought index were included in the analysis. It was found that tree mortality from the 16th century through the beginning of the 19th century caused a downward tree line recession. Sparse larch stands experienced deforestation, transforming into tundra with isolated relict trees. The maximum tree mortality and radial growth decrease were observed to have occurred at the beginning of 18th century. Now larch, at its northern boundary in Siberia, is migrating into tundra areas. Upward tree migration was induced by warming in the middle of the 19th century. Refugia played an important role in repopulation of the forest-tundra ecotone by providing a seed source and shelter for recruitment of larch regeneration. Currently this ecotone is being repopulated mainly by tree cohorts that were established after the 1930s. The last two decades of warming did not result in an acceleration of regeneration recruitment because of increased drought conditions. The regeneration line reached (but did not exceed) the pre-LIA tree line location, although contemporary tree heights and stand densities are comparatively lower than in the pre-LIA period. The mean rate of tree line upward migration has been about 0.35 m/yr (with a range of 0.21-0.58), which translates to a tree line response to temperature of about 55 m/deg C.

A Review of Advancements in Particulate Matter Sampling and Analysis and its Application to Identifying Source Impacts at Receptor Locations

EPA Science Inventory

Time-integrated (typically 24-hr) filter-based methods (historical methods) form the underpinning of our understanding of the fate, impact of source emissions at receptor locations (source impacts), and potential health and welfare effects of particulate matter (PM) in air. Over...

Spatially Informed Plant PRA Models for Security Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wheeler, Timothy A.; Thomas, Willard; Thornsbury, Eric

2006-07-01

Traditional risk models can be adapted to evaluate plant response for situations where plant systems and structures are intentionally damaged, such as from sabotage or terrorism. This paper describes a process by which traditional risk models can be spatially informed to analyze the effects of compound and widespread harsh environments through the use of 'damage footprints'. A 'damage footprint' is a spatial map of regions of the plant (zones) where equipment could be physically destroyed or disabled as a direct consequence of an intentional act. The use of 'damage footprints' requires that the basic events from the traditional probabilistic riskmore » assessment (PRA) be spatially transformed so that the failure of individual components can be linked to the destruction of or damage to specific spatial zones within the plant. Given the nature of intentional acts, extensive modifications must be made to the risk models to account for the special nature of the 'initiating events' associated with deliberate adversary actions. Intentional acts might produce harsh environments that in turn could subject components and structures to one or more insults, such as structural, fire, flood, and/or vibration and shock damage. Furthermore, the potential for widespread damage from some of these insults requires an approach that addresses the impacts of these potentially severe insults even when they occur in locations distant from the actual physical location of a component or structure modeled in the traditional PRA. (authors)« less

Diversity changes of microbial communities into hospital surface environments.

PubMed

Yano, Rika; Shimoda, Tomoko; Watanabe, Reina; Kuroki, Yasutoshi; Okubo, Torahiko; Nakamura, Shinji; Matsuo, Junji; Yoshimura, Sadako; Yamaguchi, Hiroyuki

2017-07-01

Previous works have demonstrated considerable variability in hospital cleanliness in Japan, suggesting that contamination is driven by factors that are currently poorly controlled. We undertook 16S rRNA sequence analysis to study population structures of hospital environmental microbiomes to see which factor(s) impacted contamination. One hundred forty-four samples were collected from surfaces of three hospitals with distinct sizes ("A": >500 beds, "B": 100-500 beds, "C": <100 beds). Sample locations of two ward types (Surgical and Internal) included patient room bed table (multiple) (4BT), patient overbed table (multiple) (4OT), patient room sink (multiple) (4S), patient room bed table (single) (SBT), patient overbed table (single) (SOT), patient room sink (single) (SS), nurse desk (ND), and nurse wagon (NW). Total DNA was extracted from each sample, and the 50 samples that yielded sufficient DNA were used for further 16S rRNA sequencing of hospital microbiome populations with cluster analysis. The number of assigned bacterial OTU populations was significantly decreased in hospital "C" compared to the other hospitals. Cluster analysis of sampling locations revealed that the population structure in almost all locations of hospital "C" and some locations in the other hospitals was very similar and unusually skewed with a family, Enterobacteriaceae. Interestingly, locations included patient area (4OT, 4BT, SBT) and nurse area (ND), with a device (NW) bridging the two and a place (4S and SS) shared between patients or visitors. We demonstrated diversity changes of hospital environmental microbiomes with a skewed population, presumably by medical staff pushing NWs or sinks shared by patients or visitors. Copyright © 2017 Japanese Society of Chemotherapy and The Japanese Association for Infectious Diseases. Published by Elsevier Ltd. All rights reserved.

Regulation of Heat Stress by HSF1 and GR

DTIC Science & Technology

2015-09-01

0 10 20 30 40 50 0 100 200 300 Location (µm) Fl uo re sc en ce 0 10 20 30 40 50 0 100 200 300 Location (µm) 0 10 20 30 40 50 0 100 200 300 Location...µm) Fl uo re sc en ce 0 10 20 30 40 50 0 100 200 300 Location (µm) 6   4. Impact What was the impact on the development of the principal discipline

Bioinspired engineering study of Plantae vascules for self-healing composite structures

PubMed Central

Trask, R. S.; Bond, I. P.

2010-01-01

This paper presents the first conceptual study into creating a Plantae-inspired vascular network within a fibre-reinforced polymer composite laminate, which provides an ongoing self-healing functionality without incurring a mass penalty. Through the application of a ‘lost-wax’ technique, orthogonal hollow vascules, inspired by the ‘ray cell’ structures found in ring porous hardwoods, were successfully introduced within a carbon fibre-reinforced epoxy polymer composite laminate. The influence on fibre architecture and mechanical behaviour of single vascules (located on the laminate centreline) when aligned parallel and transverse to the local host ply was characterized experimentally using a compression-after-impact test methodology. Ultrasonic C-scanning and high-resolution micro-CT X-ray was undertaken to identify the influence of and interaction between the internal vasculature and impact damage. The results clearly show that damage morphology is influenced by vascule orientation and that a 10 J low-velocity impact damage event is sufficient to breach the vasculature; a prerequisite for any subsequent self-healing function. The residual compressive strength after a 10 J impact was found to be dependent upon vascule orientation. In general, residual compressive strength decreased to 70 per cent of undamaged strength when vasculature was aligned parallel to the local host ply and a value of 63 per cent when aligned transverse. This bioinspired engineering study has illustrated the potential that a vasculature concept has to offer in terms of providing a self-healing function with minimum mass penalty, without initiating premature failure within a composite structure. PMID:19955122

Variability in clubhead presentation characteristics and ball impact location for golfers' drives.

PubMed

Betzler, Nils F; Monk, Stuart A; Wallace, Eric S; Otto, Steve R

2012-01-01

The purpose of the present study was to analyse the variability in clubhead presentation to the ball and the resulting ball impact location on the club face for a range of golfers of different ability. A total of 285 male and female participants hit multiple shots using one of four proprietary drivers. Self-reported handicap was used to quantify a participant's golfing ability. A bespoke motion capture system and user-written algorithms was used to track the clubhead just before and at impact, measuring clubhead speed, clubhead orientation, and impact location. A Doppler radar was used to measure golf ball speed. Generally, golfers of higher skill (lower handicap) generated increased clubhead speed and increased efficiency (ratio of ball speed to clubhead speed). Non-parametric statistical tests showed that low-handicap golfers exhibit significantly lower variability from shot to shot in clubhead speed, efficiency, impact location, attack angle, club path, and face angle compared with high-handicap golfers.

Vulnerability and impacts of climate change on forest and freshwater wetland ecosystems in Nepal: A review.

PubMed

Lamsal, Pramod; Kumar, Lalit; Atreya, Kishor; Pant, Krishna Prasad

2017-12-01

Climate change (CC) threatens ecosystems in both developed and developing countries. As the impacts of CC are pervasive, global, and mostly irreversible, it is gaining worldwide attention. Here we review vulnerability and impacts of CC on forest and freshwater wetland ecosystems. We particularly look at investigations undertaken at different geographic regions in order to identify existing knowledge gaps and possible implications from such vulnerability in the context of Nepal along with available adaptation programs and national-level policy supports. Different categories of impacts which are attributed to disrupting structure, function, and habitat of both forest and wetland ecosystems are identified and discussed. We show that though still unaccounted, many facets of forest and freshwater wetland ecosystems of Nepal are vulnerable and likely to be impacted by CC in the near future. Provisioning ecosystem services and landscape-level ecosystem conservation are anticipated to be highly threatened with future CC. Finally, the need for prioritizing CC research in Nepal is highlighted to close the existing knowledge gap along with the implementation of adaptation measures based on existing location specific traditional socio-ecological system.

Modelling the gravity and magnetic field anomalies of the Chicxulub crater

NASA Technical Reports Server (NTRS)

Aleman, C. Ortiz; Pilkington, M.; Hildebrand, A. R.; Roest, W. R.; Grieve, R. A. F.; Keating, P.

1993-01-01

The approximately 180-km-diameter Chicxulub crater lies buried by approximately 1 km of sediment on the northwestern corner of the Yucatan Peninsula, Mexico. Geophysical, stratigraphic and petrologic evidence support an impact origin for the structure and biostratigraphy suggests that a K/T age is possible for the impact. The crater's location is in agreement with constraints derived from proximal K/T impact-wave and ejecta deposits and its melt-rock is similar in composition to the K/T tektites. Radiometric dating of the melt rock reveals an age identical to that of the K/T tektites. The impact which produced the Chicxulub crater probably produced the K/T extinctions and understanding the now-buried crater will provide constraints on the impact's lethal effects. The outstanding preservation of the crater, the availability of detailed gravity and magnetic data sets, and the two-component target of carbonate/evaporites overlying silicate basement allow application of geophysical modeling techniques to explore the crater under most favorable circumstances. We have found that the main features of the gravity and magnetic field anomalies may be produced by the crater lithologies.

Investigating a 65-Ma-Old Smoking Gun: Deep Drilling of the Chicxulub Impact Structure

NASA Astrophysics Data System (ADS)

Dressler, B. O.; Sharpton, V. L.; Morgan, J.; Buffler, R.; Moran, D.; Smit, J.; Stöffler, D.; Urrutia, J.

The Phanerozoic paleontological record is marked by several biological extinction events. One of them, at the Cretaceous/Tertiary (K/T) boundary, was responsible for the demise of about 5% of genera and 75% of species, including the dinosaurs. These drastic and abrupt changes in the development of life on Earth puzzled paleontologists in the past. Many a cause was put forward to account for them, amongst them climate changes, disease, or overspecialization. About 20 years ago, Alvarez et al. [1980] discovered a high iridium concentration in an Italian K/T boundary clay layer. They proposed that the iridium was derived from an extra-terrestrial impact 65 Ma ago and that the impact was the cause for the K/T boundary extinctions. The iridium layer was subsequently found at K/T boundary locations worldwide. Further evidence for a K/T impact came from the discovery of shocked quartz, nano-diamonds, glass spherules, and nickel-rich spinels in microkrystites in the iridium-rich layer. There was evidence for an impact event, but no crater.

Multi-Dimensional Calibration of Impact Dynamic Models

NASA Technical Reports Server (NTRS)

Horta, Lucas G.; Reaves, Mercedes C.; Annett, Martin S.; Jackson, Karen E.

2011-01-01

NASA Langley, under the Subsonic Rotary Wing Program, recently completed two helicopter tests in support of an in-house effort to study crashworthiness. As part of this effort, work is on-going to investigate model calibration approaches and calibration metrics for impact dynamics models. Model calibration of impact dynamics problems has traditionally assessed model adequacy by comparing time histories from analytical predictions to test at only a few critical locations. Although this approach provides for a direct measure of the model predictive capability, overall system behavior is only qualitatively assessed using full vehicle animations. In order to understand the spatial and temporal relationships of impact loads as they migrate throughout the structure, a more quantitative approach is needed. In this work impact shapes derived from simulated time history data are used to recommend sensor placement and to assess model adequacy using time based metrics and orthogonality multi-dimensional metrics. An approach for model calibration is presented that includes metric definitions, uncertainty bounds, parameter sensitivity, and numerical optimization to estimate parameters to reconcile test with analysis. The process is illustrated using simulated experiment data.

Impact of Soft Tissue Heterogeneity on Augmented Reality for Liver Surgery.

PubMed

Haouchine, Nazim; Cotin, Stephane; Peterlik, Igor; Dequidt, Jeremie; Lopez, Mario Sanz; Kerrien, Erwan; Berger, Marie-Odile

2015-05-01

This paper presents a method for real-time augmented reality of internal liver structures during minimally invasive hepatic surgery. Vessels and tumors computed from pre-operative CT scans can be overlaid onto the laparoscopic view for surgery guidance. Compared to current methods, our method is able to locate the in-depth positions of the tumors based on partial three-dimensional liver tissue motion using a real-time biomechanical model. This model permits to properly handle the motion of internal structures even in the case of anisotropic or heterogeneous tissues, as it is the case for the liver and many anatomical structures. Experimentations conducted on phantom liver permits to measure the accuracy of the augmentation while real-time augmentation on in vivo human liver during real surgery shows the benefits of such an approach for minimally invasive surgery.

[Microbial diversity of sediments from the coasts of Dalian Changshan Islands].

PubMed

Li, Jialin; Wang, Zhonghua; Qin, Song; Wang, Guangyi

2011-05-01

To understand the impacts of anthropogenic activities on structure and composition of bacterial communities and to evaluate how bacterial communities respond to environmental gradients at coastal sediments. The diversity of bacterial communities in sediments from tourist and mariculture zones at coastal area of Dalian Changshan Islands was assessed using terminal restriction fragment length polymorphism (t-RFLP) and denaturing gradient gel electrophoresis (DGGE) approaches. Meanwhile, 16S rRNA clone library was constructed to reveal the composition and structure of bacterial communities in the most seriously polluted site (D4). There were much higher values of richness, Shannon-wiener and evenness index at D4 site by the analysis of terminal restriction fragments (t-RFs). The clustering result on the t-RFs areas and DGGE patterns showed that the bacterial diversity of tourist zone were more similar, while the distinction was increased with pollution levels among the tourist and mariculture zones. The 16S rRNA clone of D4 revealed that the Proteobacteria were the dominant phylum, and gamma-proteobacteria was the main class within Proteobacteria. The study documented changes in bacterial community structure by human impacts of mariculture than geographical location.

Genetic homogeneity in the deep-sea grenadier Macrourus berglax across the North Atlantic Ocean

NASA Astrophysics Data System (ADS)

Coscia, Ilaria; Castilho, Rita; Massa-Gallucci, Alexia; Sacchi, Carlotta; Cunha, Regina L.; Stefanni, Sergio; Helyar, Sarah J.; Knutsen, Halvor; Mariani, Stefano

2018-02-01

Paucity of data on population structure and connectivity in deep sea species remains a major obstacle to their sustainable management and conservation in the face of ever increasing fisheries pressure and other forms of impacts on deep sea ecosystems. The roughhead grenadier Macrourus berglax presents all the classical characteristics of a deep sea species, such as slow growth and low fecundity, which make them particularly vulnerable to anthropogenic impact, due to their low resilience to change. In this study, the population structure of the roughhead grenadier is investigated throughout its geographic distribution using two sets of molecular markers: a partial sequence of the Control Region of mitochondrial DNA and species-specific microsatellites. No evidence of significant structure was found throughout the North Atlantic, with both sets of molecular markers yielding the same results of overall homogeneity. We posit two non-mutually exclusive scenarios that can explain such outcome: i) substantial high gene flow among locations, possibly maintained by larval stages, ii) very large effective size of post-glacially expanded populations. The results can inform management strategies in this by-caught species, and contribute to the broader issue of biological connectivity in the deep ocean.

Visible Signatures of Hypersonic Reentry

DTIC Science & Technology

2013-02-01

cases, these viewing zones extend a significant distance from the impact location and/or include the impact location for a potentially significant...period of time before impact . Nomenclature V = reentry body velocity [m/s] ρ = ambient air density [kg/m3] ρ0 = sea-level air density [kg/m3] φ...time from first noticeability to impact . IV. Conclusion For a given reentry body, methods in this paper allow calculation of noticeability and

Mean first passage time for random walk on dual structure of dendrimer

NASA Astrophysics Data System (ADS)

Li, Ling; Guan, Jihong; Zhou, Shuigeng

2014-12-01

The random walk approach has recently been widely employed to study the relations between the underlying structure and dynamic of complex systems. The mean first-passage time (MFPT) for random walks is a key index to evaluate the transport efficiency in a given system. In this paper we study analytically the MFPT in a dual structure of dendrimer network, Husimi cactus, which has different application background and different structure (contains loops) from dendrimer. By making use of the iterative construction, we explicitly determine both the partial mean first-passage time (PMFT, the average of MFPTs to a given target) and the global mean first-passage time (GMFT, the average of MFPTs over all couples of nodes) on Husimi cactus. The obtained closed-form results show that PMFPT and EMFPT follow different scaling with the network order, suggesting that the target location has essential influence on the transport efficiency. Finally, the impact that loop structure could bring is analyzed and discussed.

Performance of two load-limiting subfloor concepts in full-scale general aviation airplane crash tests

NASA Technical Reports Server (NTRS)

Carden, H. D.

1984-01-01

Three six-place, low wing, twin-engine general aviation airplane test specimens were crash tested at the langley Impact Dynamics research Facility under controlled free-flight conditions. One structurally unmodified airplane was the baseline airplane specimen for the test series. The other airplanes were structurally modified to incorporate load-limiting (energy-absorbing) subfloor concepts into the structure for full scale crash test evaluation and comparison to the unmodified airplane test results. Typically, the lowest floor accelerations and anthropomorphic dummy occupant responses, and the least seat crushing of standard and load-limiting seats, occurred in the modified load-limiting subfloor airplanes wherein the greatest structural crushing of the subfloor took place. The better performing of the two load-limiting subfloor concepts reduced the peak airplane floor accelerations at the pilot and four seat/occupant locations to -25 to -30 g's as compared to approximately -50 to -55 g's acceleration magnitude for the unmodified airplane structure.

Pedestrian headform testing: inferring performance at impact speeds and for headform masses not tested, and estimating average performance in a range of real-world conditions.

PubMed

Hutchinson, T Paul; Anderson, Robert W G; Searson, Daniel J

2012-01-01

Tests are routinely conducted where instrumented headforms are projected at the fronts of cars to assess pedestrian safety. Better information would be obtained by accounting for performance over the range of expected impact conditions in the field. Moreover, methods will be required to integrate the assessment of secondary safety performance with primary safety systems that reduce the speeds of impacts. Thus, we discuss how to estimate performance over a range of impact conditions from performance in one test and how this information can be combined with information on the probability of different impact speeds to provide a balanced assessment of pedestrian safety. Theoretical consideration is given to 2 distinct aspects to impact safety performance: the test impact severity (measured by the head injury criterion, HIC) at a speed at which a structure does not bottom out and the speed at which bottoming out occurs. Further considerations are given to an injury risk function, the distribution of impact speeds likely in the field, and the effect of primary safety systems on impact speeds. These are used to calculate curves that estimate injuriousness for combinations of test HIC, bottoming out speed, and alternative distributions of impact speeds. The injuriousness of a structure that may be struck by the head of a pedestrian depends not only on the result of the impact test but also the bottoming out speed and the distribution of impact speeds. Example calculations indicate that the relationship between the test HIC and injuriousness extends over a larger range than is presently used by the European New Car Assessment Programme (Euro NCAP), that bottoming out at speeds only slightly higher than the test speed can significantly increase the injuriousness of an impact location and that effective primary safety systems that reduce impact speeds significantly modify the relationship between the test HIC and injuriousness. Present testing regimes do not take fully into account the relationship between impact severity and variations in impact conditions. Instead, they assess injury risk at a single impact speed. Hence, they may fail to differentiate risks due to the effects of bottoming out under different impact conditions. Because the level of injuriousness changes across a wide range of HIC values, even slight improvements to very stiff structures need to be encouraged through testing. Indications are that the potential of autonomous braking systems is substantial and needs to be weighted highly in vehicle safety assessments.

Lunar Impact Flash Locations from NASA's Lunar Impact Monitoring Program

NASA Technical Reports Server (NTRS)

Moser, D. E.; Suggs, R. M.; Kupferschmidt, L.; Feldman, J.

2015-01-01

Meteoroids are small, natural bodies traveling through space, fragments from comets, asteroids, and impact debris from planets. Unlike the Earth, which has an atmosphere that slows, ablates, and disintegrates most meteoroids before they reach the ground, the Moon has little-to-no atmosphere to prevent meteoroids from impacting the lunar surface. Upon impact, the meteoroid's kinetic energy is partitioned into crater excavation, seismic wave production, and the generation of a debris plume. A flash of light associated with the plume is detectable by instruments on Earth. Following the initial observation of a probable Taurid impact flash on the Moon in November 2005,1 the NASA Meteoroid Environment Office (MEO) began a routine monitoring program to observe the Moon for meteoroid impact flashes in early 2006, resulting in the observation of over 330 impacts to date. The main objective of the MEO is to characterize the meteoroid environment for application to spacecraft engineering and operations. The Lunar Impact Monitoring Program provides information about the meteoroid flux in near-Earth space in a size range-tens of grams to a few kilograms-difficult to measure with statistical significance by other means. A bright impact flash detected by the program in March 2013 brought into focus the importance of determining the impact flash location. Prior to this time, the location was estimated to the nearest half-degree by visually comparing the impact imagery to maps of the Moon. Better accuracy was not needed because meteoroid flux calculations did not require high-accuracy impact locations. But such a bright event was thought to have produced a fresh crater detectable from lunar orbit by the NASA spacecraft Lunar Reconnaissance Orbiter (LRO). The idea of linking the observation of an impact flash with its crater was an appealing one, as it would validate NASA photometric calculations and crater scaling laws developed from hypervelocity gun testing. This idea was dependent upon LRO finding a fresh impact crater associated with one of the impact flashes recorded by Earth-based instruments, either the bright event of March 2013 or any other in the database of impact observations. To find the crater, LRO needed an accurate area to search. This Technical Memorandum (TM) describes the geolocation technique developed to accurately determine the impact flash location, and by association, the location of the crater, thought to lie directly beneath the brightest portion of the flash. The workflow and software tools used to geolocate the impact flashes are described in detail, along with sources of error and uncertainty and a case study applying the workflow to the bright impact flash in March 2013. Following the successful geolocation of the March 2013 flash, the technique was applied to all impact flashes detected by the MEO between November 7, 2005, and January 3, 2014.

Architecture of the sperm whale forehead facilitates ramming combat.

PubMed

Panagiotopoulou, Olga; Spyridis, Panagiotis; Mehari Abraha, Hyab; Carrier, David R; Pataky, Todd C

2016-01-01

Herman Melville's novel Moby Dick was inspired by historical instances in which large sperm whales (Physeter macrocephalus L.) sank 19th century whaling ships by ramming them with their foreheads. The immense forehead of sperm whales is possibly the largest, and one of the strangest, anatomical structures in the animal kingdom. It contains two large oil-filled compartments, known as the "spermaceti organ" and "junk," that constitute up to one-quarter of body mass and extend one-third of the total length of the whale. Recognized as playing an important role in echolocation, previous studies have also attributed the complex structural configuration of the spermaceti organ and junk to acoustic sexual selection, acoustic prey debilitation, buoyancy control, and aggressive ramming. Of these additional suggested functions, ramming remains the most controversial, and the potential mechanical roles of the structural components of the spermaceti organ and junk in ramming remain untested. Here we explore the aggressive ramming hypothesis using a novel combination of structural engineering principles and probabilistic simulation to determine if the unique structure of the junk significantly reduces stress in the skull during quasi-static impact. Our analyses indicate that the connective tissue partitions in the junk reduce von Mises stresses across the skull and that the load-redistribution functionality of the former is insensitive to moderate variation in tissue material parameters, the thickness of the partitions, and variations in the location and angle of the applied load. Absence of the connective tissue partitions increases skull stresses, particularly in the rostral aspect of the upper jaw, further hinting of the important role the architecture of the junk may play in ramming events. Our study also found that impact loads on the spermaceti organ generate lower skull stresses than an impact on the junk. Nevertheless, whilst an impact on the spermaceti organ would reduce skull stresses, it would also cause high compressive stresses on the anterior aspect of the organ and the connective tissue case, possibly making these structures more prone to failure. This outcome, coupled with the facts that the spermaceti organ houses sensitive and essential sonar producing structures and the rostral portion of junk, rather than the spermaceti organ, is frequently a site of significant scarring in mature males suggest that whales avoid impact with the spermaceti organ. Although the unique structure of the junk certainly serves multiple functions, our results are consistent with the hypothesis that the structure also evolved to function as a massive battering ram during male-male competition.

The Effect of Head Impact Location on Day of Diagnosed Concussion in College Football.

PubMed

Liao, Steven; Lynall, Robert C; Mihalik, Jason P

2016-07-01

Scientists and clinicians have attempted to identify and understand biomechanical factors that influence concussion likelihood. The effect of impact frequency to a given head location before the concussion has not been evaluated. The purpose of this study was to compare the frequency of impacts to a given head location on days of diagnosed concussion to the frequency of impacts to a given head location before kinematically matched nonconcussive impacts. Head impact data were gathered from 33 Division I National Collegiate Athletic Association football players. Twenty-four concussions were identified and matched with impacts of similar kinematic and injury criterion values (linear acceleration, rotational acceleration, Gadd severity index, and head injury criterion) that occurred during the same event type (game, practice, or scrimmage). In addition, these same matching criteria were used to match all players to the closest kinematic/same player group. All impacts within a session before the impact of interest (concussive or matched impact) were analyzed. On days of diagnosed concussion, the concussive group sustained a lower percentage of impacts to the front of the head (34.5%) and a greater frequency of impacts to the sides (19.6%) and top (18.9%) of the head (χ(3) = 10.23, P = 0.017) as compared with the matched nonconcussive group (front = 42.5%, sides = 16.6%, top = 14.0%). No significant difference in frequency was found in impacts to the back of the head. It may be more difficult to mitigate concussive forces sustained in impacts to the top and sides of the head than the front of the head. These findings fall in line with previous research demonstrating that reduced impact magnitudes may lessen concussion risk. Studying appropriate training paradigms to develop safer playing techniques on the field is warranted.

Anatomy of the Chesapeake Bay impact structure revealed by seismic imaging, Delmarva Peninsula, Virginia, USA

USGS Publications Warehouse

Catchings, R.D.; Powars, D.S.; Gohn, G.S.; Horton, J. Wright; Goldman, M.R.; Hole, J.A.

2008-01-01

A 30-km-long, radial seismic reflection and refraction survey completed across the northern part of the late Eocene Chesapeake Bay impact structure (CBIS) on the Delmarva Peninsula, Virginia, USA, confirms that the CBIS is a complex central-peak crater. We used a tomographic P wave velocity model and low-fold reflection images, constrained by data from two deep boreholes located on the profile, to interpret the structure and composition of the upper 5 km of crust. The seismic images exhibit well-defined structural features, including (with increasing radial distance) a collapsed central uplift, a breccia-filled moat, and a collapsed transient-crater margin (which collectively constitute a ???40-km-wide collapsed transient crater), and a shallowly deformed annular trough. These seismic images are the first to resolve the deep structure of the crater (>1 km) and the boundaries between the central uplift, moat, and annular trough. Several distinct seismic signatures distinguish breccia units from each other and from more coherent crystalline rocks below the central uplift, moat, and annular trough. Within the moat, breccia extends to a minimum depth of 1.5 km or a maximum of 3.5 km, depending upon the interpretation of the deepest layered materials. The images show ???350 to 500 m of postimpact sediments above the impactites. The imaged structure of the CBIS indicates a complex sequence of event during the cratering process that will provide new constraints for numerical modeling. Copyright 2008 by the American Geophysical Union.

NDT evaluation of long-term bond durability of CFRP-structural systems applied to RC highway bridges

NASA Astrophysics Data System (ADS)

Crawford, Kenneth C.

2016-06-01

The long-term durability of CFRP structural systems applied to reinforced-concrete (RC) highway bridges is a function of the system bond behavior over time. The sustained structural load performance of strengthened bridges depends on the carbon fiber-reinforced polymer (CFRP) laminates remaining 100 % bonded to concrete bridge members. Periodic testing of the CFRP-concrete bond condition is necessary to sustain load performance. The objective of this paper is to present a non-destructive testing (NDT) method designed to evaluate the bond condition and long-term durability of CFRP laminate (plate) systems applied to RC highway bridges. Using the impact-echo principle, a mobile mechanical device using light impact hammers moving along the length of a bonded CFRP plate produces unique acoustic frequencies which are a function of existing CFRP plate-concrete bond conditions. The purpose of this method is to test and locate CFRP plates de-bonded from bridge structural members to identify associated deterioration in bridge load performance. Laboratory tests of this NDT device on a CFRP plate bonded to concrete with staged voids (de-laminations) produced different frequencies for bonded and de-bonded areas of the plate. The spectra (bands) of frequencies obtained in these tests show a correlation to the CFRP-concrete bond condition and identify bonded and de-bonded areas of the plate. The results of these tests indicate that this NDT impact machine, with design improvements, can potentially provide bridge engineers a means to rapidly evaluate long lengths of CFRP laminates applied to multiple highway bridges within a national transportation infrastructure.

Demonstration of UAV deployment and control of mobile wireless sensing networks for modal analysis of structures

NASA Astrophysics Data System (ADS)

Zhou, Hao; Hirose, Mitsuhito; Greenwood, William; Xiao, Yong; Lynch, Jerome; Zekkos, Dimitrios; Kamat, Vineet

2016-04-01

Unmanned aerial vehicles (UAVs) can serve as a powerful mobile sensing platform for assessing the health of civil infrastructure systems. To date, the majority of their uses have been dedicated to vision and laser-based spatial imaging using on-board cameras and LiDAR units, respectively. Comparatively less work has focused on integration of other sensing modalities relevant to structural monitoring applications. The overarching goal of this study is to explore the ability for UAVs to deploy a network of wireless sensors on structures for controlled vibration testing. The study develops a UAV platform with an integrated robotic gripper that can be used to install wireless sensors in structures, drop a heavy weight for the introduction of impact loads, and to uninstall wireless sensors for reinstallation elsewhere. A pose estimation algorithm is embedded in the UAV to estimate the location of the UAV during sensor placement and impact load introduction. The Martlet wireless sensor network architecture is integrated with the UAV to provide the UAV a mobile sensing capability. The UAV is programmed to command field deployed Martlets, aggregate and temporarily store data from the wireless sensor network, and to communicate data to a fixed base station on site. This study demonstrates the integrated UAV system using a simply supported beam in the lab with Martlet wireless sensors placed by the UAV and impact load testing performed. The study verifies the feasibility of the integrated UAV-wireless monitoring system architecture with accurate modal characteristics of the beam estimated by modal analysis.

Microbial community structure across a wastewater-impacted riparian buffer zone in the southeastern coastal plain.

PubMed

Ducey, T F; Johnson, P R; Shriner, A D; Matheny, T A; Hunt, P G

2013-01-01

Riparian buffer zones are important for both natural and developed ecosystems throughout the world because of their ability to retain nutrients, prevent soil erosion, protect aquatic environments from excessive sedimentation, and filter pollutants. Despite their importance, the microbial community structures of riparian buffer zones remains poorly defined. Our objectives for this study were twofold: first, to characterize the microbial populations found in riparian buffer zone soils; and second, to determine if microbial community structure could be linked to denitrification enzyme activity (DEA). To achieve these objectives, we investigated the microbial populations of a riparian buffer zone located downslope of a pasture irrigated with swine lagoon effluent, utilizing DNA sequencing of the 16S rDNA, DEA, and quantitative PCR (qPCR) of the denitrification genes nirK, nirS, and nosZ. Clone libraries of the 16S rDNA gene were generated from each of twelve sites across the riparian buffer with a total of 986 partial sequences grouped into 654 operational taxonomic units (OTUs). The Proteobacteria were the dominant group (49.8% of all OTUs), with the Acidobacteria also well represented (19.57% of all OTUs). Analysis of qPCR results identified spatial relationships between soil series, site location, and gene abundance, which could be used to infer both incomplete and total DEA rates.

The Proximity of Ribosomal Protein Genes to oriC Enhances Vibrio cholerae Fitness in the Absence of Multifork Replication.

PubMed

Soler-Bistué, Alfonso; Timmermans, Michaël; Mazel, Didier

2017-02-28

Recent works suggest that bacterial gene order links chromosome structure to cell homeostasis. Comparative genomics showed that, in fast-growing bacteria, ribosomal protein genes (RP) locate near the replication origin ( oriC ). We recently showed that Vibrio cholerae employs this positional bias as a growth optimization strategy: under fast-growth conditions, multifork replication increases RP dosage and expression. However, RP location may provide advantages in a dosage-independent manner: for example, the physical proximity of the many ribosomal components, in the context of a crowded cytoplasm, may favor ribosome biogenesis. To uncover putative dosage-independent effects, we studied isogenic V. cholerae derivatives in which the major RP locus, S10-spc-α (S10), was relocated to alternative genomic positions. When bacteria grew fast, bacterial fitness was reduced according to the S10 relative distance to oriC The growth of wild-type V. cholerae could not be improved by additional copies of the locus, suggesting a physiologically optimized genomic location. Slow growth is expected to uncouple RP position from dosage, since multifork replication does not occur. Under these conditions, we detected a fitness impairment when S10 was far from oriC Deep sequencing followed by marker frequency analysis in the absence of multifork replication revealed an up to 30% S10 dosage reduction associated with its relocation that closely correlated with fitness alterations. Hence, the impact of S10 location goes beyond a growth optimization strategy during feast periods. RP location may be important during the whole life cycle of this pathogen. IMPORTANCE The role of gene order within the bacterial chromosome is poorly understood. In fast growers, the location of genes linked with the expression of genetic information (i.e., transcription and translation) is biased toward oriC It was proposed that the location of these genes helps to maximize their expression by recruiting multifork replication during fast growth. Our results show that such genomic positioning impacts cell fitness beyond fast-growth conditions, probably across the whole life cycle of fast growers. Thus, the genomic position of key highly expressed genes, such as RP, was finely tuned during the evolution of fast-growing bacteria and may also be important in slow growers. In the near future, many more genes whose genomic position impacts bacterial phenotype will be described. These studies will contribute to discovery the rules of genome organization and application of them for the design of synthetic chromosomes and the creation of artificial life forms. Copyright © 2017 Soler-Bistué et al.

Different Histories, Different Destinies‒Impact of Evolutionary History and Population Genetic Structure on Extinction Risk of the Adriatic Spined Loaches (Genus Cobitis; Cypriniformes, Actinopterygii).

PubMed

Buj, Ivana; Ćaleta, Marko; Marčić, Zoran; Šanda, Radek; Vukić, Jasna; Mrakovčić, Milorad

2015-01-01

The region of Balkans is often considered as an ichthyologic "hot spot", with a great number of species and high portion of endemics living in fresh waters in a relatively small area. The Adriatic watershed in Croatia and Herzegovina is inhabited by six spined loach species (genus Cobitis) whose extinction risk estimations were based solely on their extent of occurrence (and/or area of occupancy) and its fragmentation, and conservation proposals do not consider diversity below species level. In this investigation we employed molecular genetic methods to describe present genetic structure of the Adriatic spined loaches and reveal their demographic history. The divergence of the Adriatic lineages inside the genus Cobitis started in Miocene and lasted until Pleistocene epoch. Geological events responsible for shaping recent diversity of spined loaches in the Adriatic basin are: the Dinarid Mountains upwelling, the evolution of Dinaric Lake system, local tectonic activity, river connections during glaciations and differences in sea level. Even though all the investigated species inhabit karstic rivers located in the same geographic area and that were subject of similar geological events, the results obtained reveal great differences in their genetic diversity and structure and point out the necessity of different conservation measures to ensure their future viability. High level of genetic polymorphism is characteristic for species located more to the south. Two species comprised of more than one population have completely different intraspecific structure; populations of C. illyrica are genetically distinct and represent separate evolutionary significant units, whereas intraspecific structure of C. narentana corresponds to metapopulational pattern. Without population genetic data, evolutionary significant units could be easily misidentified. Furthermore, the obtained results affirm that population genetic measurements are able to detect differences among closely located and related species and estimate extinction risk even more accurately than currently applied IUCN criteria.

The Impact of Continuity Editing in Narrative Film on Event Segmentation

PubMed Central

Magliano, Joseph P.; Zacks, Jeffrey M.

2011-01-01

Filmmakers use continuity editing to engender a sense of situational continuity or discontinuity at editing boundaries. The goal of this study was to assess the impact of continuity editing on how people perceive the structure of events in a narrative film and to identify brain networks that are associated with the processing of different types of continuity editing boundaries. Participants viewed a commercially produced film and segmented it into meaningful events while brain activity was recorded with functional MRI. We identified three degrees of continuity that can occur at editing locations: edits that are continuous in space, time, and action; edits that are discontinuous in space or time but continuous in action; and edits that are discontinuous in action as well as space or time. Discontinuities in action had the biggest impact on behavioral event segmentation and discontinuities in space and time had minor effects. Edits were associated with large transient increases in early visual areas. Spatial-temporal changes and action changes produced strikingly different patterns of transient change, and provided evidence that specialized mechanisms in higher-order perceptual processing regions are engaged to maintain continuity of action in the face of spatiotemporal discontinuities. These results suggest that commercial film editing is shaped to support the comprehension of meaningful events that bridge breaks in low-level visual continuity, and even breaks in continuity of spatial and temporal location. PMID:21972849

Overview of the Transport Rotorcraft Airframe Crash Testbed (TRACT) Full Scale Crash Tests

NASA Technical Reports Server (NTRS)

Annett, Martin; Littell, Justin

2015-01-01

The Transport Rotorcraft Airframe Crash Testbed (TRACT) full-scale tests were performed at NASA Langley Research Center's Landing and Impact Research Facility in 2013 and 2014. Two CH-46E airframes were impacted at 33-ft/s forward and 25-ft/s vertical combined velocities onto soft soil, which represents a severe, but potentially survivable impact scenario. TRACT 1 provided a baseline set of responses, while TRACT 2 included retrofits with composite subfloors and other crash system improvements based on TRACT 1. For TRACT 2, a total of 18 unique experiments were conducted to evaluate Anthropomorphic Test Devices (ATD) responses, seat and restraint performance, cargo restraint effectiveness, patient litter behavior, and activation of emergency locator transmitters and crash sensors. Combinations of Hybrid II, Hybrid III, and ES-2 ATDs were placed in forward and side facing seats and occupant results were compared against injury criteria. The structural response of the airframe was assessed based on accelerometers located throughout the airframe and using three-dimensional photogrammetric techniques. Analysis of the photogrammetric data indicated regions of maximum deflection and permanent deformation. The response of TRACT 2 was noticeably different in the horizontal direction due to changes in the cabin configuration and soil surface, with higher acceleration and damage occurring in the cabin. Loads from ATDs in energy absorbing seats and restraints were within injury limits. Severe injury was likely for ATDs in forward facing passenger seats.

SoilBioHedge, harnessing hedgerow soil biodiversity for restoration of arable soil quality and resilience to climatic extremes and land use changes: The impacts of arable to ley conversion on soil hydrological properties

NASA Astrophysics Data System (ADS)

Grayson, Richard; Holden, Joseph; Chapman, Pippa; Hunt, Sarah; Leake, Jonathan

2017-04-01

Modern agricultural practices pose a significant threat to soil security. Continuous conventional cultivation has been observed to deplete soil organic matter, degrade soil structure, reduce water drainage and water holding capacity, increase nitrate leaching, damage the ecosystem engineer earthworm and mycorrhiza populations and increase the susceptibility of soil and crops to the impacts of climatic stress through decreased resilience to flood and drought conditions. The SoilBioHedge project aims to determine the effectiveness of using grass-clover leys linking hedgerows to arable fields in restoring functional biodiversity, soil quality and resilience to drought and excess rainfall in arable farming. Paired 70m long ley strips have been inserted in to 4 fields. Within each field one ley is connected to the margin while in the other a small 1m fallow area and a steel mesh barrier inserted to bedrock is being used to disconnect the ley and margin and prevent macrofaunal movement from the margin to the ley. As part of the SoilBioHedge project we are undertaking a range of analyses to establish the impacts of arable to ley conversion on key hydrological properties of agricultural soils. Soil moisture is being continuously monitored at three depths at 48 separate locations, in addition monthly manual measurements are being taken at 1158 locations. Arable-to-ley conversion is expected to increase soil macrofaunal activity especially in locations closer to hedgerows, enhancing macropore development. Therefore the proportion of water percolating into macropores, mesopores and micropores is being measured using tension infiltrometers which also allow the calculation of saturated hydraulic conductivity. Soil cores have been extracted to examine impacts on bulk and particle density and subsequently porosity, with hydraulic conductivity being measured using a lab permeameter. Here we present the results of these analyses over the first 24 months of the project. This includes the impacts of this arable ley conversion on soil moisture dynamics and functional macroporosity.

Virtopsy -- noninvasive detection of occult bone lesions in postmortem MRI: additional information for traffic accident reconstruction.

PubMed

Buck, Ursula; Christe, Andreas; Naether, Silvio; Ross, Steffen; Thali, Michael J

2009-05-01

In traffic accidents with pedestrians, cyclists or motorcyclists, patterned impact injuries as well as marks on clothes can be matched to the injury-causing vehicle structure in order to reconstruct the accident and identify the vehicle which has hit the person. Therefore, the differentiation of the primary impact injuries from other injuries is of great importance. Impact injuries can be identified on the external injuries of the skin, the injured subcutaneous and fat tissue, as well as the fractured bones. Another sign of impact is a bone bruise. The bone bruise, or occult bone lesion, means a bleeding in the subcortical bone marrow, which is presumed to be the result of micro-fractures of the medullar trabeculae. The aim of this study was to prove that bleeding in the subcortical bone marrow of the deceased can be detected using the postmortem noninvasive magnetic resonance imaging. This is demonstrated in five accident cases, four involving pedestrians and one a cyclist, where bone bruises were detected in different bones as a sign of impact occurring in the same location as the external and soft tissue impact injuries.

Relaxation mechanisms, structure and properties of semi-coherent interfaces

DOE PAGES

Shao, Shuai; Wang, Jian

2015-10-15

In this work, using the Cu–Ni (111) semi-coherent interface as a model system, we combine atomistic simulations and defect theory to reveal the relaxation mechanisms, structure, and properties of semi-coherent interfaces. By calculating the generalized stacking fault energy (GSFE) profile of the interface, two stable structures and a high-energy structure are located. During the relaxation, the regions that possess the stable structures expand and develop into coherent regions; the regions with high-energy structure shrink into the intersection of misfit dislocations (nodes). This process reduces the interface excess potential energy but increases the core energy of the misfit dislocations and nodes.more » The core width is dependent on the GSFE of the interface. The high-energy structure relaxes by relative rotation and dilatation between the crystals. The relative rotation is responsible for the spiral pattern at nodes. The relative dilatation is responsible for the creation of free volume at nodes, which facilitates the nodes’ structural transformation. Several node structures have been observed and analyzed. In conclusion, the various structures have significant impact on the plastic deformation in terms of lattice dislocation nucleation, as well as the point defect formation energies.« less

Microburst characteristics determined from 1988-1991 TDWR testbed measurements

NASA Technical Reports Server (NTRS)

Biron, Paul J.; Isaminger, Mark A.

1992-01-01

This paper presents some recent results germane to airborne windshear system design and certification. We first discuss the data analysis procedure and the associated caveats. The relative frequency, severity, and duration of microburst hazards at the various locations is important for determining the tradeoffs between safety and operational impact of false alerts which are encompassed in detection system thresholds. We then consider radar/lidar design issues such as reflective in microbursts and the vertical structure of outflows. Finally, we provide recent surface thermodynamic data associated with microbursts.

San Francisco floating STOLport study

NASA Technical Reports Server (NTRS)

1974-01-01

The operational, economic, environmental, social and engineering feasibility of utilizing deactivated maritime vessels as a waterfront quiet short takeoff and landing facility to be located near the central business district of San Francisco was investigated. Criteria were developed to evaluate each site, and minimum standards were established for each criterion. Predicted conditions at the two sites were compared to the requirements for each of the 11 criteria as a means of evaluating site performance. Criteria include land use, community structure, economic impact, access, visual character, noise, air pollution, natural environment, weather, air traffic, and terminal design.

Assessing the health impact of transnational corporations: a case study on McDonald's Australia.

PubMed

Anaf, Julia; Baum, Frances E; Fisher, Matt; Harris, Elizabeth; Friel, Sharon

2017-02-06

The practices of transnational corporations affect population health through production methods, shaping social determinants of health, or influencing the regulatory structures governing their activities. There has been limited research on community exposures to TNC policies and practices. Our pilot research used McDonald's Australia to test methods for assessing the health impacts of one TNC within Australia. We adapted existing Health Impact Assessment methods to assess McDonald's activities. Data identifying potential impacts were sourced through document analysis, including McDonald's corporate literature; media analysis and semi-structured interviews. We commissioned a spatial and socioeconomic analysis of McDonald's restaurants in Australia through Geographic Information System technology. The data was mapped against a corporate health impact assessment framework which included McDonald's Australia's political and business practices; products and marketing; workforce, social, environmental and economic conditions; and consumers' health related behaviours. We identified both positive and detrimental aspects of McDonald's Australian operations across the scope of the CHIA framework. We found that McDonald's outlets were slightly more likely to be located in areas of lower socioeconomic status. McDonald's workplace conditions were found to be more favourable than those in many other countries which reflects compliance with Australian employment regulations. The breadth of findings revealed the need for governments to strengthen regulatory mechanisms that are conducive to health; the opportunity for McDonald's to augment their corporate social responsibility initiatives and bolster reputational endorsement; and civil society actors to inform their advocacy towards health and equity outcomes from TNC operations. Our study indicates that undertaking a corporate health impact assessment is possible, with the different methods revealing sufficient information to realise that strong regulatory frameworks are need to help to avoid or to mediate negative health impacts.

Socioeconomic Impact Assessment of the Los Angeles Automatic Vehicle Monitoring (AVM) Demonstration

DOT National Transportation Integrated Search

1982-09-01

This report presents a socioeconomic impact assessment of the Automatic Vehicle Monitoring (AVM) Demonstration in Los Angeles. An AVM system uses location, communication, and data processing subsystems to monitor the locations of appropriately equipp...

Impact of oceanic submesoscale coherent structures on marine top predators: new tools and challenges

NASA Astrophysics Data System (ADS)

Tew-Kai, E.; Sudre, J.; Gremillet, D.; Yahia, H.; Rossi, V.; Hernandez-Garcia, E.; López, C.; Marsac, F.; Weimerskirch, H.; Garçon, V.

2011-12-01

In recent years it appears that meso- and submesoscale features (fronts, eddies, filaments) in surface ocean flow have a crucial influence on marine ecosystems. Their dynamics partly control the foraging behaviour and the movements of marine top. One of the challenges in ecology is to define critical habitats and understand the rules of habitat selection. Recently new tools for detection of coherent structures at submesoscale open the way for new studies never investigated before in marine ecology. Through two examples we highlight novel research on the importance of submesoscale structures for the spatial distribution of marine top predators. We studied two seabird populations with contrasting characteristics: Frigatebirds in the Mozambique Channel, and Cape gannets in the Benguela upwelling off southern Africa. Frigatebirds are mainly offshore birds while Cape gannets do not venture beyond the continental shelf. For these two studies, we used products derived from remote sensing data, to describe submesoscale coherent structures (<10km). In the first example, using Finite-Size Lyapunov Exponents (FSLE), we have identified Lagrangian coherent structures (LCSs) present in the surface flow of the Mozambique Channel resulting from an intense mesoscale activity. By comparing seabird satellite positions with LCSs locations, we demonstrate that frigatebirds track precisely these structures in the Mozambique Channel, providing the first evidence that a top predator is able to track these FSLE ridges to locate food patches. Although many questions remain unanswered, this work remains a pioneering on this topic. Despite the interest of FSLE, they are limited to offshore areas due to altimetry products limitation on continental shelves. However, many seabirds operate in coastal areas undergoing stronger anthropogenic pressures, such as Cape gannets off South Africa. The Benguela system is characterized by an upwelling inhabited by numerous fronts and filaments that very likely have a strong impact on seabird spatial distribution, and it was not possible to implement FSLE in this area. Thus, we used a newly developed method based on the singularity exponents calculated from remotely sensed data of ocean colour and SST, which delivers a precise picture of meso and submeso-scale structures off the coast. Preliminary results on understanding the rules of habitat selection by Cape gannets, and contribution to the conservation of this endangered species will be presented.

Urban-rural variations in air quality and health impacts in northern India

NASA Astrophysics Data System (ADS)

Karambelas, A. N.; Holloway, T.; Fiore, A. M.; Kinney, P.; DeFries, R. S.; Kiesewetter, G.; Heyes, C.

2017-12-01

Ambient air pollution in India is a severe problem, contributing to negative health impacts and early death. Ground-based monitors often used to quantify health impacts are often located in urban regions, however approximately 70% of India's population resides in rural areas. We use high-resolution concentrations from the regional Community Multi-scale Air Quality (CMAQ) model over densely-populated northern India to estimate air quality and health impacts due to anthropogenic emission sectors separately for urban and rural regions. Modeled concentrations inform relative risk calculations and exposure estimates as performed in the Global Burden of Disease. Anthropogenic emissions from the International Institute for Applied Systems Analysis (IIASA) Greenhouse Gas-Air Pollution Interactions and Synergies (GAINS) model following version 5a of the Evaluating the Climate and Air Quality Impacts of Short-Lived Pollutants project gridding structure are updated to reflect urban- and rural-specific activity information for transportation and residential combustion, and industrial and electrical generating unit location and magnitude information. We estimate 314,000 (95% Confidence Interval: 304,000—323,000) and 58,000 (CI: 39,000—70,000) adults (25 years or older) die prematurely each year from PM2.5 and O3 respectively in northern India, with the greatest impacts along the Indo-Gangetic Plain. Using urban and rural population distributions, we estimate that the majority of premature deaths resulting from PM2.5 and O3 are in rural (292,000) as opposed to urban (79,000) regions. These findings indicate the need for designing monitoring networks and ground-based health studies in rural areas of India to more accurately quantify the true health implications of ambient air pollution, in addition to supporting model evaluation. Using this urban-versus-rural emissions framework, we are assessing anthropogenic contributions to regional air quality and health impacts, and examining mitigation strategies to reduce anthropogenic emissions, improve air quality, and reduce PM2.5 and O3 attributable premature death in the near-term.

Unraveling the impact of built-environmental self-modification of the local inhabitants in their attempt to reduce the urban flood impact in Grogol, Sukoharjo*

NASA Astrophysics Data System (ADS)

Wanabakti, M. J.; Susilo, C. R.; Nathania, M.; Putri, C. Y.

2018-05-01

Due in part to climate change impact and the lack of environmental awareness of urban societies, urban flood disasters have increased in both frequency and impacted areas. The inevitable destructive impact is also experienced by urban inhabitants within Grogol District, Sukoharjo, Central Java. Situated within the fast-growing peri-urban area of Surakarta, the geographical condition of the district, which is located in the convergence of Bengawan Solo River and four different streamlet rivers is undoubtedly critical to flood. Since the position of the peri-urban area is along the border of Surakarta City and Sukoharjo Regency, the site is a strategic locus of the main city’s urban expansion. However, its border location has made flood-reduction programs challenging to be implemented, due to unclear territorial admiration and distribution. Because of the absence of flood-reduction programs in the area, local inhabitants have been independently developing physical and built environmental modification of their settlements. By analyzing the two-months built environmental fieldwork research in Grogol Sukoharjo, this paper unravels both the success and the conflicting impact of local self-initiative modification in Grogol Sukoharjo. By combining the two-month field observation with the semi-structured interviews in three sub-districts of Grogol, this paper finds that the very pragmatic self-modification taken by the inhabitants results in short-term reductions of flood impact and increases the secure feelings of inhabitants to continue living in their neighborhoods. However, the lack of proper technical supervision from experts and the absence of inter-neighborhood coordination leads to future additional damage on the flood-prone areas of Grogol. The paper also reveals that one pragmatic physical self-modification solution taken by one neighborhood may lead to an extra flood-threat to other neighborhoods.

Colony-level effects of imidacloprid in subterranean termites (Isoptera: Rhinotermitidae).

PubMed

Parman, Vincent; Vargo, Edward L

2010-06-01

We determined the impact of imidacloprid (Premise) on colonies of Reticulitermes spp. (Isoptera: Rhinotermitidae) through soil applications in the field. We selected 11 houses in the Raleigh, NC, area with active termite infestations. In-ground monitoring stations (mean = 75.9 stations) were installed around each house, and samples of termites visiting the monitors, in mud tubes, as well as samples from wood debris in the yard, were collected monthly for up to 14 mo to determine the numbers and locations of colonies present before treatment. We used microsatellite genetic markers to identify individual colonies present on each property. All houses were treated with Premise 75 WSP by using an exterior perimeter/interior spot treatment. After treatment, termite samples were collected monthly for 3 mo and then quarterly for 2 yr to track the fate of colonies. Of the 12 treated colonies (those attacking structures), 75% disappeared within 90 d and were not detected again. In contrast, only 25% of 48 untreated colonies (located 2 m or further from the treatment zone) and 40% of the six likely treated colonies (located within 0.5 m of the treatment zone but not known to be attacking the structure) were not detected again during the study. Our findings are consistent with strong colony-level effects of soil treatments with imidacloprid, resulting in the suppression or elimination of Reticulitermes spp. colonies in many cases.

Marginal inherited structures impact on the oblique convergent N American Plate/ Central Caribbean plate-boundary in the Northern Caribbean. The tectonic evolution since Miocene times based on Haiti data acquired onshore and offshore since 2012- a step toward an ADP Drilling Proposal (Haiti-DRILL).

NASA Astrophysics Data System (ADS)

Ellouz, N.; Hamon, Y.; Deschamps, R.; Battani, A.; Wessels, R.; Boisson, D.; Prepetit, C.; Momplaisir, R.

2017-12-01

Since Early Paleogene times, the North Caribbean plate is colliding obliquely with the south continental part of the old N. American Margins, which is represented by various segments from West to East, inherited from Jurassic times. Location, amount of displacement, rotation and the structural deformation of these margin segments, resulting from the dislocation of the continental N American margin, are not clearly yet established. At present, the plate limits are marked either by two left lateral faults west and inside Haiti (OSF in the North and EPGF in the South), oblique collision front (further west in Cuba), oblique subducted segments (to the East, Porto-Rico). From our recent works operated both offshore (Haiti-SIS and Haiti-BGF surveys 2012-2015) and onshore (field campaigns 2013-2017) in Haitian zone, the position of the present-day and paleo major limits have been redefined. These paleolimits have been reconstructed up to early Miocene times, based on: restoration of regional structural cross-sections, sedimentology and on paleoenvironement studies. In a preliminary way, we analyzed the complexity of the tectonic heritage with possible nature, heterogeneity of the crustal fragments and associated margins close to Haiti (age, structure, environment, location of the dislocated blocks through times) which profoundly impact the partitioning of the deformation along this complex transformed margin. The change in the structure wavelength, decollement level variations are primary constraints in the restoration of the main units and do impose a deep connection along specific segments either related to strike-slip or to splay faults. The asymmetry on the repartition of the fault activity tend to prove that the past motion related to "EPGF transfer zone" is mainly partitioned in Haiti to the North of the present-day EPGF position. At present, these results are still coherent with the distribution of the aftershoks registered after 2010, and with the present-day seismicity during the last years.

Influence of GTP/GDP and magnesium ion on the solvated structure of the protein FtsZ: a molecular dynamics study.

PubMed

Jamous, Carla; Basdevant, Nathalie; Ha-Duong, Tap

2014-01-01

We present here a structural analysis of ten extensive all-atom molecular dynamics simulations of the monomeric protein FtsZ in various binding states. Since the polymerization and GTPase activities of FtsZ depend on the nature of a bound nucleotide as well as on the presence of a magnesium ion, we studied the structural differences between the average conformations of the following five systems: FtsZ-Apo, FtsZ-GTP, FtsZ-GDP, FtsZ-GTP-Mg, and FtsZ-GDP-Mg. The in silico solvated average structure of FtsZ-Apo significantly differs from the crystallographic structure 1W59 of FtsZ which was crystallized in a dimeric form without nucleotide and magnesium. The simulated Apo form of the protein also clearly differs from the FtsZ structures when it is bound to its ligand, the most important discrepancies being located in the loops surrounding the nucleotide binding pocket. The three average structures of FtsZ-GTP, FtsZ-GDP, and FtsZ-GTP-Mg are overall similar, except for the loop T7 located at the opposite side of the binding pocket and whose conformation in FtsZ-GDP notably differs from the one in FtsZ-GTP and FtsZ-GTP-Mg. The presence of a magnesium ion in the binding pocket has no impact on the FtsZ conformation when it is bound to GTP. In contrast, when the protein is bound to GDP, the divalent cation causes a translation of the nucleotide outwards the pocket, inducing a significant conformational change of the loop H6-H7 and the top of helix H7.

Manufacture and performance of carbon/epoxy 3-D woven composites

NASA Technical Reports Server (NTRS)

Brandt, J.; Drechsler, K.; Mohamed, Mansour; Gu, PU

1992-01-01

This paper evaluates 3-D orthogonal woven carbon/epoxy composites. Preforms were manufactured on an automatic 3-D weaving machine developed at N.C. State University. Matrix infiltration was conducted at MBB Central Laboratories. Testing was carried out at both locations and the joint results will be reported. The properties investigated include: interlaminar shear strength, compression, compression after impact, bending, tensile and penetration resistance. The 3-D orthogonal woven composites were compared with laminated and other 3-D composites made with preforms having interlock structure. C-scans were used to examine the quality of infiltration and the damage area after impact. The performance of the composites made from the 3-D orthogonal preforms showed superior properties compared to the other composites. The penetration resistance test showed unexpectedly very good performance.

National Biological Service Research Supports Watershed Planning

USGS Publications Warehouse

Snyder, Craig D.

1996-01-01

The National Biological Service's Leetown Science Center is investigating how human impacts on watershed, riparian, and in-stream habitats affect fish communities. The research will provide the basis for a Ridge and Valley model that will allow resource managers to accurately predict and effectively mitigate human impacts on water quality. The study takes place in the Opequon Creek drainage basin of West Virginia. A fourth-order tributary of the Potomac, the basin falls within the Ridge and Valley. The study will identify biological components sensitive to land use patterns and the condition of the riparian zone; the effect of stream size, location, and other characteristics on fish communities; the extent to which remote sensing can reliable measure the riparian zone; and the relationship between the rate of landscape change and the structure of fish communities.

The geomorphology of Ceres.

PubMed

Buczkowski, D L; Schmidt, B E; Williams, D A; Mest, S C; Scully, J E C; Ermakov, A I; Preusker, F; Schenk, P; Otto, K A; Hiesinger, H; O'Brien, D; Marchi, S; Sizemore, H; Hughson, K; Chilton, H; Bland, M; Byrne, S; Schorghofer, N; Platz, T; Jaumann, R; Roatsch, T; Sykes, M V; Nathues, A; De Sanctis, M C; Raymond, C A; Russell, C T

2016-09-02

Analysis of Dawn spacecraft Framing Camera image data allows evaluation of the topography and geomorphology of features on the surface of Ceres. The dwarf planet is dominated by numerous craters, but other features are also common. Linear structures include both those associated with impact craters and those that do not appear to have any correlation to an impact event. Abundant lobate flows are identified, and numerous domical features are found at a range of scales. Features suggestive of near-surface ice, cryomagmatism, and cryovolcanism have been identified. Although spectroscopic analysis has currently detected surface water ice at only one location on Ceres, the identification of these potentially ice-related features suggests that there may be at least some ice in localized regions in the crust. Copyright © 2016, American Association for the Advancement of Science.

Impact of meteorological inflow uncertainty on tracer transport and source estimation in urban atmospheres

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lucas, Donald D.; Gowardhan, Akshay; Cameron-Smith, Philip

2015-08-08

Here, a computational Bayesian inverse technique is used to quantify the effects of meteorological inflow uncertainty on tracer transport and source estimation in a complex urban environment. We estimate a probability distribution of meteorological inflow by comparing wind observations to Monte Carlo simulations from the Aeolus model. Aeolus is a computational fluid dynamics model that simulates atmospheric and tracer flow around buildings and structures at meter-scale resolution. Uncertainty in the inflow is propagated through forward and backward Lagrangian dispersion calculations to determine the impact on tracer transport and the ability to estimate the release location of an unknown source. Ourmore » uncertainty methods are compared against measurements from an intensive observation period during the Joint Urban 2003 tracer release experiment conducted in Oklahoma City.« less

Halogenated Alkyltetrazoles for the Rational Design of FeII Spin-Crossover Materials: Fine-Tuning of the Ligand Size.

PubMed

Müller, Danny; Knoll, Christian; Seifried, Marco; Welch, Jan M; Giester, Gerald; Reissner, Michael; Weinberger, Peter

2018-04-06

1-(3-Halopropyl)-1H-tetrazoles and their corresponding Fe II spin-crossover complexes have been investigated in a combined experimental and theoretical study. Halogen substitution was found to positively influence the spin transition, shifting the transition temperature about 70 K towards room temperature. Halogens located at the ω position were found to be too far away from the coordinating tetrazole moiety to have an electronic impact on the spin transition. The subtle variation of the steric demand of the ligand in a highly comparable series was found to have a comparatively large impact on the spin-transition behavior, which highlights the sensitivity of the effect to subtle structural changes. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Measuring patients' satisfaction with pharmaceutical services at a public hospital in Qatar.

PubMed

Khudair, Imran Fahmi; Raza, Syed Asif

2013-01-01

The aim of this paper is to study pharmacy service impact on patient satisfaction and to determine what factors saliently link with pharmaceutical service performance at Hamad General Hospital. A patient satisfaction questionnaire was designed using the literature and consultation with Hamad General Hospital medical experts. The questionnaire contained 22 items that focused on five influencing factors: promptness; attitude; supply; location; medication education; and respondent demographic aspects. A total of 220 respondents completed the questionnaire. An exploratory factor analysis was used to group items and a structural equation model was developed to test causality between five factors along with their influence on patient satisfaction. The study establishes statistical evidence that patient satisfaction is positively influenced by service promptness, pharmacist attitude, medication counseling, pharmacy location and waiting area. Several socio-demographic characteristics have statistically different effect on satisfaction, notably: gender; marital status; health status; age; educational level; and ethnicity. However, medication supply did not influence patient satisfaction. Pharmaceutical services are recognized as an essential healthcare-system component. Their impact on customer satisfaction has been investigated in many countries; however, there is no such study in Qatar. The findings identify pharmaceutical service performance indicators and provide guidelines to improve Qatari pharmaceutical services.

Experimental Photogrammetric Techniques Used on Five Full-Scale Aircraft Crash Tests

NASA Technical Reports Server (NTRS)

Littell, Justin D.

2016-01-01

Between 2013 and 2015, full-scale crash tests were conducted on five aircraft at the Landing and Impact Research Facility (LandIR) at NASA Langley Research Center (LaRC). Two tests were conducted on CH-46E airframes as part of the Transport Rotorcraft Airframe Crash Testbed (TRACT) project, and three tests were conduced on Cessna 172 aircraft as part of the Emergency Locator Transmitter Survivability and Reliability (ELTSAR) project. Each test served to evaluate a variety of crashworthy systems including: seats, occupants, restraints, composite energy absorbing structures, and Emergency Locator Transmitters. As part of each test, the aircraft were outfitted with a variety of internal and external cameras that were focused on unique aspects of the crash event. A subset of three camera was solely used in the acquisition of photogrammetric test data. Examples of this data range from simple two-dimensional marker tracking for the determination of aircraft impact conditions to entire full-scale airframe deformation to markerless tracking of Anthropomorphic Test Devices (ATDs, a.k.a. crash test dummies) during the crash event. This report describes and discusses the techniques used and implications resulting from the photogrammetric data acquired from each of the five tests.

Acoustic emission source location in composite structure by Voronoi construction using geodesic curve evolution.

PubMed

Gangadharan, R; Prasanna, G; Bhat, M R; Murthy, C R L; Gopalakrishnan, S

2009-11-01

Conventional analytical/numerical methods employing triangulation technique are suitable for locating acoustic emission (AE) source in a planar structure without structural discontinuities. But these methods cannot be extended to structures with complicated geometry, and, also, the problem gets compounded if the material of the structure is anisotropic warranting complex analytical velocity models. A geodesic approach using Voronoi construction is proposed in this work to locate the AE source in a composite structure. The approach is based on the fact that the wave takes minimum energy path to travel from the source to any other point in the connected domain. The geodesics are computed on the meshed surface of the structure using graph theory based on Dijkstra's algorithm. By propagating the waves in reverse virtually from these sensors along the geodesic path and by locating the first intersection point of these waves, one can get the AE source location. In this work, the geodesic approach is shown more suitable for a practicable source location solution in a composite structure with arbitrary surface containing finite discontinuities. Experiments have been conducted on composite plate specimens of simple and complex geometry to validate this method.

Effect of Impact Location on the Response of Shuttle Wing Leading Edge Panel 9

NASA Technical Reports Server (NTRS)

Lyle, Karen H.; Spellman, Regina L.; Hardy, Robin C.; Fasanella, Edwin L.; Jackson, Karen E.

2005-01-01

The objective of this paper is to compare the results of several simulations performed to determine the worst-case location for a foam impact on the Space Shuttle wing leading edge. The simulations were performed using the commercial non-linear transient dynamic finite element code, LS-DYNA. These simulations represent the first in a series of parametric studies performed to support the selection of the worst-case impact scenario. Panel 9 was selected for this study to enable comparisons with previous simulations performed during the Columbia Accident Investigation. The projectile for this study is a 5.5-in cube of typical external tank foam weighing 0.23 lb. Seven locations spanning the panel surface were impacted with the foam cube. For each of these cases, the foam was traveling at 1000 ft/s directly aft, along the orbiter X-axis. Results compared from the parametric studies included strains, contact forces, and material energies for various simulations. The results show that the worst case impact location was on the top surface, near the apex.

The Location-Specific Role of Proteoglycans in the Flexor Carpi Ulnaris Tendon

PubMed Central

Buckley, Mark R.; Huffman, George R.; Iozzo, Renato V.; Birk, David E.; Soslowsky, Louis J.

2015-01-01

Tendons like the flexor carpi ulnaris (FCU) that contain region-specific distributions of proteoglycans (PGs) as a result of the heterogeneous, multi-axial loads they are subjected to in vivo provide valuable models for understanding structure-function relationships in connective tissues. However, the contributions of specific PGs to FCU tendon mechanical properties are unknown. Therefore, the objective of this study was to determine how the location-dependent, viscoelastic mechanical properties of the FCU tendon are impacted individually by PG-associated glycosaminoglycans (GAGs) and by two small leucine-rich proteoglycans (SLRPs), biglycan and decorin. Full length FCU tendons from biglycan- and decorin-null mice were compared to wild type mice to evaluate the effects of specific SLRPs, while chondroitinase ABC digestion of isolated specimens removed from the tendon midsubstance was used to determine how chontroitin/dermatan sulfate (CS/DS) GAGs impact mechanics in mature FCU tendons. A novel combined genetic knockout/ digestion technique also was employed to compare SLRP-null and wild-type tendons in the absence of CS/DS GAGs that may impact properties in the mature state. In all genotypes, mechanical properties in the FCU tendon midsubstance were not affected by GAG digestion. Full-length tendons exhibited complex, multi-axial deformation under tension that may be associated with their in vivo loading environment. Mechanical properties were adversely affected by the absence of biglycan, and a decreased modulus localized in the center of the tendon was measured. These results help elucidate the role that local alterations in proteoglycan levels may play in processes that adversely impact tendon functionality including injury and pathology. PMID:23941206

Silicon Carbide Found in K/T Boundary Layer: Implication for Asteroid Collision with Planet Earth

NASA Astrophysics Data System (ADS)

Leung, I. S.; Tsao, C.

2016-12-01

An event at the end of the Cretaceous Period 65.5 m.y. ago produced an impact structure 300 km in diameter designated the Chicxulub Crater, located partly on the Yucatan Peninsula and the Caribbian Sea floor. Mass extinction following that event killed 75% of Earth's living species, including dinosaurs. To this date, the killer space object has not been identified, but it was frequently conjectured to be a comet or an asteroid. The goal of our study was to search for evidence which might implicate the culprit. The Chicxulub impact caused extensive wildfires producing Ir-rich dust fallouts in worldwide localities, among which the least contaminated by land-derived sediments may be situated on deep ocean floors. Our study is based on a sample of pelagic clay from the giant piston core LL44-GPC3 taken from the Pacific Plate, north of the Hawaiian Islands (Woods Hole Oceanographic Institution). The 1-cm thick Ir-rich layer was located at a downcore depth of 1055-1056 cm below sea floor. From a 5 cubic cm sample provided by Jim Broda, we found 29 impact glass spherules and 4 silicon carbide (SiC) crystals. SiC has been reported in carbonaceous meteorites. Our findings of SiC in the K/T boundary layer seem to implicate that an asteroid having composition akin to that of carbonaceous chondrites might have been the killer projectile during the Chicxulub event. However, impact by a comet cannot be ruled out, since the mineralogy of cometary dust is as yet unknown.

The persistence of the attentional bias to regularities in a changing environment.

PubMed

Yu, Ru Qi; Zhao, Jiaying

2015-10-01

The environment often is stable, but some aspects may change over time. The challenge for the visual system is to discover and flexibly adapt to the changes. We examined how attention is shifted in the presence of changes in the underlying structure of the environment. In six experiments, observers viewed four simultaneous streams of objects while performing a visual search task. In the first half of each experiment, the stream in the structured location contained regularities, the shapes in the random location were randomized, and gray squares appeared in two neutral locations. In the second half, the stream in the structured or the random location may change. In the first half of all experiments, visual search was facilitated in the structured location, suggesting that attention was consistently biased toward regularities. In the second half, this bias persisted in the structured location when no change occurred (Experiment 1), when the regularities were removed (Experiment 2), or when new regularities embedded in the original or novel stimuli emerged in the previously random location (Experiments 3 and 6). However, visual search was numerically but no longer reliably faster in the structured location when the initial regularities were removed and new regularities were introduced in the previously random location (Experiment 4), or when novel random stimuli appeared in the random location (Experiment 5). This suggests that the attentional bias was weakened. Overall, the results demonstrate that the attentional bias to regularities was persistent but also sensitive to changes in the environment.

Brain tissue analysis of impacts to American football helmets.

PubMed

Post, Andrew; Kendall, Marshall; Cournoyer, Janie; Karton, Clara; Oeur, R Anna; Dawson, Lauren; Hoshizaki, T Blaine

2018-02-01

Concussion in American football is a prevalent concern. Research has been conducted examining frequencies, location, and thresholds for concussion from impacts. Little work has been done examining how impact location may affect risk of concussive injury. The purpose of this research was to examine how impact site on the helmet and type of impact, affects the risk of concussive injury as quantified using finite element modelling of the human head and brain. A linear impactor was used to impact a helmeted Hybrid III headform in several locations and using centric and non-centric impact vectors. The resulting dynamic response was used as input for the Wayne State Brain Injury Model to determine the risk of concussive injury by utilizing maximum principal strain as the predictive variable. The results demonstrated that impacts that occur primarily to the side of the head resulted in higher magnitudes of strain in the grey and white matter, as well as the brain stem. Finally, commonly worn American football helmets were used in this research and significant risk of injury was incurred for all impacts. These results suggest that improvements in American football helmets are warranted, in particular for impacts to the side of the helmet.

The 2.3-Angstrom Structure of Porcine Circovirus 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khayat, Reza; Brunn, Nicholas; Speir, Jeffrey A.

Porcine circovirus 2 (PCV2) is a T = 1 nonenveloped icosahedral virus that has had severe impact on the swine industry. Here we report the crystal structure of an N-terminally truncated PCV2 virus-like particle at 2.3-{angstrom} resolution, and the cryo-electron microscopy (cryo-EM) image reconstruction of a full-length PCV2 virus-like particle at 9.6-{angstrom} resolution. This is the first atomic structure of a circovirus. The crystal structure revealed that the capsid protein fold is a canonical viral jelly roll. The loops connecting the strands of the jelly roll define the limited features of the surface. Sulfate ions interacting with the surface andmore » electrostatic potential calculations strongly suggest a heparan sulfate binding site that allows PCV2 to gain entry into the cell. The crystal structure also allowed previously determined epitopes of the capsid to be visualized. The cryo-EM image reconstruction showed that the location of the N terminus, absent in the crystal structure, is inside the capsid. As the N terminus was previously shown to be antigenic, it may externalize through viral 'breathing'.« less

Frequency and location of head impact exposures in individual collegiate football players.

PubMed

Crisco, Joseph J; Fiore, Russell; Beckwith, Jonathan G; Chu, Jeffrey J; Brolinson, Per Gunnar; Duma, Stefan; McAllister, Thomas W; Duhaime, Ann-Christine; Greenwald, Richard M

2010-01-01

Measuring head impact exposure is a critical step toward understanding the mechanism and prevention of sport-related mild traumatic brain (concussion) injury, as well as the possible effects of repeated subconcussive impacts. To quantify the frequency and location of head impacts that individual players received in 1 season among 3 collegiate teams, between practice and game sessions, and among player positions. Cohort study. Collegiate football field. One hundred eighty-eight players from 3 National Collegiate Athletic Association football teams. Participants wore football helmets instrumented with an accelerometer-based system during the 2007 fall season. The number of head impacts greater than 10 g and location of the impacts on the player's helmet were recorded and analyzed for trends and interactions among teams (A, B, or C), session types, and player positions using Kaplan-Meier survival curves. The total number of impacts players received was nonnormally distributed and varied by team, session type, and player position. The maximum number of head impacts for a single player on each team was 1022 (team A), 1412 (team B), and 1444 (team C). The median number of head impacts on each team was 4.8 (team A), 7.5 (team B), and 6.6 (team C) impacts per practice and 12.1 (team A), 14.6 (team B), and 16.3 (team C) impacts per game. Linemen and linebackers had the largest number of impacts per practice and per game. Offensive linemen had a higher percentage of impacts to the front than to the back of the helmet, whereas quarterbacks had a higher percentage to the back than to the front of the helmet. The frequency of head impacts and the location on the helmet where the impacts occur are functions of player position and session type. These data provide a basis for quantifying specific head impact exposure for studies related to understanding the biomechanics and clinical aspects of concussion injury, as well as the possible effects of repeated subconcussive impacts in football.