Reflow process stabilization by chemical characteristics and process conditions

NASA Astrophysics Data System (ADS)

Kim, Myoung-Soo; Park, Jeong-Hyun; Kim, Hak-Joon; Kim, Il-Hyung; Jeon, Jae-Ha; Gil, Myung-Goon; Kim, Bong-Ho

2002-07-01

With the shrunken device rule below 130nm, the patterning of smaller contact hole with enough process margin is required for mass production. Therefore, shrinking technology using thermal reflow process has been applied for smaller contact hole formation. In this paper, we have investigated the effects of chemical characteristics such as molecular weight, blocking ratio of resin, cross-linker amount and solvent type with its composition to reflow process of resist and found the optimized chemical composition for reflow process applicable condition. And several process conditions like resist coating thickness and multi-step thermal reflow method have been also evaluated to stabilize the pattern profile and improve CD uniformity after reflow process. From the experiment results, it was confirmed that the effect of crosslinker in resist to reflow properties such as reflow temperature and reflow rate were very critical and it controlled the pattern profile during reflow processing. And also, it showed stable CD uniformity and improved resist properties for top loss, film shrinkage and etch selectivity. The application of lower coating thickness of resist induced symmetric pattern profile even at edge with wider process margin. The introduction of two-step baking method for reflow process showed uniform CD value, also. It is believed that the application of resist containing crosslinker and optimized process conditions for smaller contact hole patterning is necessary for the mass production with a design rule below 130nm.

Assessing the efficacy of PEF treatments for improving polyphenol extraction during red wine vinifications.

PubMed

Saldaña, Guillermo; Cebrián, Guillermo; Abenoza, María; Sánchez-Gimeno, Cristina; Álvarez, Ignacio; Raso, Javier

2017-02-01

The influence of the electric field intensity and pulse width on the improvement of total polyphenol index (TPI) and colour intensity (CI) during extraction in an ethanolic solution (30%) and during fermentation-maceration has been investigated in different grape varieties: Grenache from two harvesting times, Syrah and Tempranillo. The aim of this study was to develop a procedure to establish the PEF treatment conditions that cause enough permeabilization in the skin cells of different grape varieties to obtain a significant improvement in the vinification process in terms of increment on the polyphenol content or reduction of maceration time. Results obtained in this investigation indicate that extraction of polyphenols in a solution of ethanol (30%) for 2 h could be a suitable procedure to know if the PEF technology is effective for improving extraction of polyphenols from the grapes during vinification and to determine the most suitable PEF treatment conditions to obtain this objective. Improvement in the extraction during vinification only was observed with those grapes and under treatment conditions in which the improvement of the polyphenol extraction was higher than 40%. Other interesting observation from this research is the highest efficacy of PEF when treatments of the same duration are applied using longer pulses. Therefore, in a continuous process, where the flow processed is determined by the frequency applied by the PEF generator, it is possible to increase the processing capacity of the PEF installation. Benefits from PEF treatment of the grapes before the maceration step in the vinification process have been demonstrated. Nevertheless, the characteristics of the grapes may change in different vintages and grape varieties. Therefore, it is of high importance to be able to determine the optimum PEF conditions in order to obtain the desired benefit during the vinification. The rapid method developed permits to determine PEF process parameters before the application of the PEF treatment with the objective of facilitating the phenolic extraction and therefore, reducing the maceration time. In these cases, it would be possible to remove the skins from the rest of the wine earlier, and therefore, increase the processing capacity of the winery.

Acoustic Signal Processing for Pipe Condition Assessment (WaterRF Report 4360)

EPA Science Inventory

Unique to prestressed concrete cylinder pipe (PCCP), individual wire breaks create an excitation in the pipe wall that may vary in response to the remaining compression of the pipe core. This project was designed to improve acoustic signal processing for pipe condition assessment...

Development of an Optimization Methodology for the Aluminum Alloy Wheel Casting Process

NASA Astrophysics Data System (ADS)

Duan, Jianglan; Reilly, Carl; Maijer, Daan M.; Cockcroft, Steve L.; Phillion, Andre B.

2015-08-01

An optimization methodology has been developed for the aluminum alloy wheel casting process. The methodology is focused on improving the timing of cooling processes in a die to achieve improved casting quality. This methodology utilizes (1) a casting process model, which was developed within the commercial finite element package, ABAQUS™—ABAQUS is a trademark of Dassault Systèms; (2) a Python-based results extraction procedure; and (3) a numerical optimization module from the open-source Python library, Scipy. To achieve optimal casting quality, a set of constraints have been defined to ensure directional solidification, and an objective function, based on the solidification cooling rates, has been defined to either maximize, or target a specific, cooling rate. The methodology has been applied to a series of casting and die geometries with different cooling system configurations, including a 2-D axisymmetric wheel and die assembly generated from a full-scale prototype wheel. The results show that, with properly defined constraint and objective functions, solidification conditions can be improved and optimal cooling conditions can be achieved leading to process productivity and product quality improvements.

Negative Emotion Weakens the Degree of Self-Reference Effect: Evidence from ERPs

PubMed Central

Fan, Wei; Zhong, Yiping; Li, Jin; Yang, Zilu; Zhan, Youlong; Cai, Ronghua; Fu, Xiaolan

2016-01-01

We investigated the influence of negative emotion on the degree of self-reference effect using event-related potentials (ERPs). We presented emotional pictures and self-referential stimuli (stimuli that accelerate and improve processing and improve memory of information related to an individual’s self-concept) in sequence. Participants judged the color of the target stimulus (self-referential stimuli). ERP results showed that the target stimuli elicited larger P2 amplitudes under neutral conditions than under negative emotional conditions. Under neutral conditions, N2 amplitudes for highly self-relevant names (target stimulus) were smaller than those for any other names. Under negative emotional conditions, highly and moderately self-referential stimuli activated smaller N2 amplitudes. P3 amplitudes activated by self-referential processing under negative emotional conditions were smaller than neutral conditions. In the left and central sites, highly self-relevant names activated larger P3 amplitudes than any other names. But in the central sites, moderately self-relevant names activated larger P3 amplitudes than non-self-relevant names. The findings indicate that negative emotional processing could weaken the degree of self-reference effect. PMID:27733836

Health Monitoring and Management for Manufacturing Workers in Adverse Working Conditions.

PubMed

Xu, Xiaoya; Zhong, Miao; Wan, Jiafu; Yi, Minglun; Gao, Tiancheng

2016-10-01

In adverse working conditions, environmental parameters such as metallic dust, noise, and environmental temperature, directly affect the health condition of manufacturing workers. It is therefore important to implement health monitoring and management based on important physiological parameters (e.g., heart rate, blood pressure, and body temperature). In recent years, new technologies, such as body area networks, cloud computing, and smart clothing, have allowed the improvement of the quality of services. In this article, we first give five-layer architecture for health monitoring and management of manufacturing workers. Then, we analyze the system implementation process, including environmental data processing, physical condition monitoring and system services and management, and present the corresponding algorithms. Finally, we carry out an evaluation and analysis from the perspective of insurance and compensation for manufacturing workers in adverse working conditions. The proposed scheme will contribute to the improvement of workplace conditions, realize health monitoring and management, and protect the interests of manufacturing workers.

A Peer Assessment System to Improve Student Team Experiences

ERIC Educational Resources Information Center

Anson, Robert; Goodman, James A.

2014-01-01

Groups are frequently used in courses, but there is substantial evidence that insufficient attention is paid to creating conditions for successful teamwork. One key condition is high-quality, individual, and team-level feedback. An online peer assessment system and team improvement process was developed for this test case based on three design…

Process, including membrane separation, for separating hydrogen from hydrocarbons

DOEpatents

Baker, Richard W.; Lokhandwala, Kaaeid A.; He, Zhenjie; Pinnau, Ingo

2001-01-01

Processes for providing improved methane removal and hydrogen reuse in reactors, particularly in refineries and petrochemical plants. The improved methane removal is achieved by selective purging, by passing gases in the reactor recycle loop across membranes selective in favor of methane over hydrogen, and capable of exhibiting a methane/hydrogen selectivity of at least about 2.5 under the process conditions.

Priority-setting and hospital strategic planning: a qualitative case study.

PubMed

Martin, Douglas; Shulman, Ken; Santiago-Sorrell, Patricia; Singer, Peter

2003-10-01

To describe and evaluate the priority-setting element of a hospital's strategic planning process. Qualitative case study and evaluation against the conditions of 'accountability for reasonableness' of a strategic planning process at a large urban university-affiliated hospital. The hospital's strategic planning process met the conditions of 'accountability for reasonableness' in large part. Specifically: the hospital based its decisions on reasons (both information and criteria) that the participants felt were relevant to the hospital; the number and type of participants were very extensive; the process, decisions and reasons were well communicated throughout the organization, using multiple communication vehicles; and the process included an ethical framework linked to an effort to evaluate and improve the process. However, there were opportunities to improve the process, particularly by giving participants more time to absorb the information relevant to priority-setting decisions, more time to take difficult decisions and some means to appeal or revise decisions. A case study linked to an evaluation using 'accountability for reasonableness' can serve to improve priority-setting in the context of hospital strategic planning.

Flow chemistry using milli- and microstructured reactors-from conventional to novel process windows.

PubMed

Illg, Tobias; Löb, Patrick; Hessel, Volker

2010-06-01

The terminology Novel Process Window unites different methods to improve existing processes by applying unconventional and harsh process conditions like: process routes at much elevated pressure, much elevated temperature, or processing in a thermal runaway regime to achieve a significant impact on process performance. This paper is a review of parts of IMM's works in particular the applicability of above mentioned Novel Process Windows on selected chemical reactions. First, general characteristics of microreactors are discussed like excellent mass and heat transfer and improved mixing quality. Different types of reactions are presented in which the use of microstructured devices led to an increased process performance by applying Novel Process Windows. These examples were chosen to demonstrate how chemical reactions can benefit from the use of milli- and microstructured devices and how existing protocols can be changed toward process conditions hitherto not applicable in standard laboratory equipment. The used milli- and microstructured reactors can also offer advantages in other areas, for example, high-throughput screening of catalysts and better control of size distribution in a particle synthesis process by improved mixing, etc. The chemical industry is under continuous improvement. So, a lot of research is being done to synthesize high value chemicals, to optimize existing processes in view of process safety and energy consumption and to search for new routes to produce such chemicals. Leitmotifs of such undertakings are often sustainable development(1) and Green Chemistry(2).

Methods for improved forewarning of condition changes in monitoring physical processes

DOEpatents

Hively, Lee M.

2013-04-09

This invention teaches further improvements in methods for forewarning of critical events via phase-space dissimilarity analysis of data from biomedical equipment, mechanical devices, and other physical processes. One improvement involves objective determination of a forewarning threshold (U.sub.FW), together with a failure-onset threshold (U.sub.FAIL) corresponding to a normalized value of a composite measure (C) of dissimilarity; and providing a visual or audible indication to a human observer of failure forewarning and/or failure onset. Another improvement relates to symbolization of the data according the binary numbers representing the slope between adjacent data points. Another improvement relates to adding measures of dissimilarity based on state-to-state dynamical changes of the system. And still another improvement relates to using a Shannon entropy as the measure of condition change in lieu of a connected or unconnected phase space.

Intelligent Performance Analysis with a Natural Language Interface

NASA Astrophysics Data System (ADS)

Juuso, Esko K.

2017-09-01

Performance improvement is taken as the primary goal in the asset management. Advanced data analysis is needed to efficiently integrate condition monitoring data into the operation and maintenance. Intelligent stress and condition indices have been developed for control and condition monitoring by combining generalized norms with efficient nonlinear scaling. These nonlinear scaling methodologies can also be used to handle performance measures used for management since management oriented indicators can be presented in the same scale as intelligent condition and stress indices. Performance indicators are responses of the process, machine or system to the stress contributions analyzed from process and condition monitoring data. Scaled values are directly used in intelligent temporal analysis to calculate fluctuations and trends. All these methodologies can be used in prognostics and fatigue prediction. The meanings of the variables are beneficial in extracting expert knowledge and representing information in natural language. The idea of dividing the problems into the variable specific meanings and the directions of interactions provides various improvements for performance monitoring and decision making. The integrated temporal analysis and uncertainty processing facilitates the efficient use of domain expertise. Measurements can be monitored with generalized statistical process control (GSPC) based on the same scaling functions.

Fear recognition impairment in early-stage Alzheimer's disease: when focusing on the eyes region improves performance.

PubMed

Hot, Pascal; Klein-Koerkamp, Yanica; Borg, Céline; Richard-Mornas, Aurélie; Zsoldos, Isabella; Paignon Adeline, Adeline; Thomas Antérion, Catherine; Baciu, Monica

2013-06-01

A decline in the ability to identify fearful expression has been frequently reported in patients with Alzheimer's disease (AD). In patients with severe destruction of the bilateral amygdala, similar difficulties have been reduced by using an explicit visual exploration strategy focusing on gaze. The current study assessed the possibility of applying a similar strategy in AD patients to improve fear recognition. It also assessed the possibility of improving fear recognition when a visual exploration strategy induced AD patients to process the eyes region. Seventeen patients with mild AD and 34 healthy subjects (17 young adults and 17 older adults) performed a classical task of emotional identification of faces expressing happiness, anger, and fear in two conditions: The face appeared progressively from the eyes region to the periphery (eyes region condition) or it appeared as a whole (global condition). Specific impairment in identifying a fearful expression was shown in AD patients compared with older adult controls during the global condition. Fear expression recognition was significantly improved in AD patients during the eyes region condition, in which they performed similarly to older adult controls. Our results suggest that using a different strategy of face exploration, starting first with processing of the eyes region, may compensate for a fear recognition deficit in AD patients. Findings suggest that a part of this deficit could be related to visuo-perceptual impairments. Additionally, these findings suggest that the decline of fearful face recognition reported in both normal aging and in AD may result from impairment of non-amygdalar processing in both groups and impairment of amygdalar-dependent processing in AD. Copyright © 2013 Elsevier Inc. All rights reserved.

Comparing Binaural Pre-processing Strategies II: Speech Intelligibility of Bilateral Cochlear Implant Users.

PubMed

Baumgärtel, Regina M; Hu, Hongmei; Krawczyk-Becker, Martin; Marquardt, Daniel; Herzke, Tobias; Coleman, Graham; Adiloğlu, Kamil; Bomke, Katrin; Plotz, Karsten; Gerkmann, Timo; Doclo, Simon; Kollmeier, Birger; Hohmann, Volker; Dietz, Mathias

2015-12-30

Several binaural audio signal enhancement algorithms were evaluated with respect to their potential to improve speech intelligibility in noise for users of bilateral cochlear implants (CIs). 50% speech reception thresholds (SRT50) were assessed using an adaptive procedure in three distinct, realistic noise scenarios. All scenarios were highly nonstationary, complex, and included a significant amount of reverberation. Other aspects, such as the perfectly frontal target position, were idealized laboratory settings, allowing the algorithms to perform better than in corresponding real-world conditions. Eight bilaterally implanted CI users, wearing devices from three manufacturers, participated in the study. In all noise conditions, a substantial improvement in SRT50 compared to the unprocessed signal was observed for most of the algorithms tested, with the largest improvements generally provided by binaural minimum variance distortionless response (MVDR) beamforming algorithms. The largest overall improvement in speech intelligibility was achieved by an adaptive binaural MVDR in a spatially separated, single competing talker noise scenario. A no-pre-processing condition and adaptive differential microphones without a binaural link served as the two baseline conditions. SRT50 improvements provided by the binaural MVDR beamformers surpassed the performance of the adaptive differential microphones in most cases. Speech intelligibility improvements predicted by instrumental measures were shown to account for some but not all aspects of the perceptually obtained SRT50 improvements measured in bilaterally implanted CI users. © The Author(s) 2015.

Comparing Binaural Pre-processing Strategies II

PubMed Central

Hu, Hongmei; Krawczyk-Becker, Martin; Marquardt, Daniel; Herzke, Tobias; Coleman, Graham; Adiloğlu, Kamil; Bomke, Katrin; Plotz, Karsten; Gerkmann, Timo; Doclo, Simon; Kollmeier, Birger; Hohmann, Volker; Dietz, Mathias

2015-01-01

Several binaural audio signal enhancement algorithms were evaluated with respect to their potential to improve speech intelligibility in noise for users of bilateral cochlear implants (CIs). 50% speech reception thresholds (SRT50) were assessed using an adaptive procedure in three distinct, realistic noise scenarios. All scenarios were highly nonstationary, complex, and included a significant amount of reverberation. Other aspects, such as the perfectly frontal target position, were idealized laboratory settings, allowing the algorithms to perform better than in corresponding real-world conditions. Eight bilaterally implanted CI users, wearing devices from three manufacturers, participated in the study. In all noise conditions, a substantial improvement in SRT50 compared to the unprocessed signal was observed for most of the algorithms tested, with the largest improvements generally provided by binaural minimum variance distortionless response (MVDR) beamforming algorithms. The largest overall improvement in speech intelligibility was achieved by an adaptive binaural MVDR in a spatially separated, single competing talker noise scenario. A no-pre-processing condition and adaptive differential microphones without a binaural link served as the two baseline conditions. SRT50 improvements provided by the binaural MVDR beamformers surpassed the performance of the adaptive differential microphones in most cases. Speech intelligibility improvements predicted by instrumental measures were shown to account for some but not all aspects of the perceptually obtained SRT50 improvements measured in bilaterally implanted CI users. PMID:26721921

On Becoming Better Human Beings: Six Stories to Live by

ERIC Educational Resources Information Center

Wivestad, Stein M.

2013-01-01

What are the conditions required for becoming better human beings? What are our limitations and possibilities? I understand "becoming better" as a combined improvement process bringing persons "up from" a negative condition and "up to" a positive one. Today there is a tendency to understand improvement in a one-sided way as a movement up to the…

How can survival processing improve memory encoding?

PubMed

Luo, Meng; Geng, Haiyan

2013-11-01

We investigated the psychological mechanism of survival processing advantage from the perspective of false memory in two experiments. Using a DRM paradigm in combination with analysis based on signal detection theory, we were able to separately examine participants' utilization of verbatim representation and gist representation. Specifically, in Experiment 1, participants rated semantically related words in a survival scenario for a survival condition but rated pleasantness of words in the same DRM lists for a non-survival control condition. The results showed that participants demonstrated more gist processing in the survival condition than in the pleasantness condition; however, the degree of item-specific processing in the two encoding conditions did not significantly differ. In Experiment 2, the control task was changed to a category rating task, in which participants were asked to make category ratings of words in the category lists. We found that the survival condition involved more item-specific processing than did the category condition, but we found no significant difference between the two encoding conditions at the level of gist processing. Overall, our study demonstrates that survival processing can simultaneously promote gist and item-specific representations. When the control tasks only promoted either item-specific representation or gist representation, memory advantages of survival processing occurred.

A participatory model for improving occupational health and safety: improving informal sector working conditions in Thailand.

PubMed

Manothum, Aniruth; Rukijkanpanich, Jittra; Thawesaengskulthai, Damrong; Thampitakkul, Boonwa; Chaikittiporn, Chalermchai; Arphorn, Sara

2009-01-01

The purpose of this study was to evaluate the implementation of an Occupational Health and Safety Management Model for informal sector workers in Thailand. The studied model was characterized by participatory approaches to preliminary assessment, observation of informal business practices, group discussion and participation, and the use of environmental measurements and samples. This model consisted of four processes: capacity building, risk analysis, problem solving, and monitoring and control. The participants consisted of four local labor groups from different regions, including wood carving, hand-weaving, artificial flower making, and batik processing workers. The results demonstrated that, as a result of applying the model, the working conditions of the informal sector workers had improved to meet necessary standards. This model encouraged the use of local networks, which led to cooperation within the groups to create appropriate technologies to solve their problems. The authors suggest that this model could effectively be applied elsewhere to improve informal sector working conditions on a broader scale.

Enhancing dewaterability of waste activated sludge by combined oxidative conditioning process with zero-valent iron and peroxymonosulfate.

PubMed

Zhou, Xu; Jin, Wenbiao; Chen, Hongyi; Chen, Chuan; Han, Songfang; Tu, Renjie; Wei, Wei; Gao, Shu-Hong; Xie, Guo-Jun; Wang, Qilin

2017-11-01

The enhancement of sludge dewaterability is of great importance for facilitating the sludge disposal during the operation of wastewater treatment plants. In this study, a novel oxidative conditioning approach was applied to enhance the dewaterability of waste activated sludge by the combination of zero-valent iron (ZVI) and peroxymonosulfate (PMS). It was found that the dewaterability of sludge was significantly improved after the addition of ZVI (0-4 g/g TSS) (TSS: total suspended solids) and PMS (0-1 g/g TSS). The optimal addition amount of ZVI and PMS was 0.25 g/g TSS and 0.1 g/g TSS, respectively, under which the capillary suction time of the sludge was reduced by approximately 50%. The decomposition of sludge flocs could contribute to the improved sludge dewaterability. Economic analysis demonstrated that the proposed conditioning process with ZVI and PMS was more economical than the ZVI + peroxydisulfate and the traditional Fenton conditioning processes.

Musical-Pedagogical Conditions of Preparation of Teachers for the Implementation of Innovative Process at Modern School

ERIC Educational Resources Information Center

Kovalev, Dmitry A.; Khussainova, Gulzada A.; Balagazova, Svetlana T.; Tamarasar, Zhankul

2016-01-01

This article considers improvement of public morale, raising the emotional and aesthetic culture of young people, their patriotic feelings by providing the musical-pedagogical conditions of training future teachers for the implementation of innovative processes in modern school. The world science would benefit from using the Kazakh musical…

Implementing and Sustaining School Improvement. The Informed Educator Series

ERIC Educational Resources Information Center

Protheroe, Nancy

2011-01-01

This "Informed Educator" examines research-proven strategies for implementing and sustaining school improvement by looking at the key elements of the process, enabling conditions for improvement, issues of school culture, and implementation. It also looks at school turnarounds and how to sustain school improvement once reforms are implemented.

Improving stamping simulation accuracy by accounting for realistic friction and lubrication conditions: Application to the door-outer of the Mercedes-Benz C-class Coupé

NASA Astrophysics Data System (ADS)

Hol, J.; Wiebenga, J. H.; Stock, J.; Wied, J.; Wiegand, K.; Carleer, B.

2016-08-01

In the stamping of automotive parts, friction and lubrication play a key role in achieving high quality products. In the development process of new automotive parts, it is therefore crucial to accurately account for these effects in sheet metal forming simulations. Only then, one can obtain reliable and realistic simulation results that correspond to the actual try-out and mass production conditions. In this work, the TriboForm software is used to accurately account for tribology-, friction-, and lubrication conditions in stamping simulations. The enhanced stamping simulations are applied and validated for the door-outer of the Mercedes- Benz C-Class Coupe. The project results demonstrate the improved prediction accuracy of stamping simulations with respect to both part quality and actual stamping process conditions.

[Work organisation improvement methods applied to activities of Blood Transfusion Establishments (BTE): Lean Manufacturing, VSM, 5S].

PubMed

Bertholey, F; Bourniquel, P; Rivery, E; Coudurier, N; Follea, G

2009-05-01

Continuous improvement of efficiency as well as new expectations from customers (quality and safety of blood products) and employees (working conditions) imply constant efforts in Blood Transfusion Establishments (BTE) to improve work organisations. The Lean method (from "Lean" meaning "thin") aims at identifying wastages in the process (overproduction, waiting, over-processing, inventory, transport, motion) and then reducing them in establishing a mapping of value chain (Value Stream Mapping). It consists in determining the added value of each step of the process from a customer perspective. Lean also consists in standardizing operations while implicating and responsabilizing all collaborators. The name 5S comes from the first letter of five operations of a Japanese management technique: to clear, rank, keep clean, standardize, make durable. The 5S method leads to develop the team working inducing an evolution of the way in the management is performed. The Lean VSM method has been applied to blood processing (component laboratory) in the Pays de la Loire BTE. The Lean 5S method has been applied to blood processing, quality control, purchasing, warehouse, human resources and quality assurance in the Rhône-Alpes BTE. The experience returns from both BTE shows that these methods allowed improving: (1) the processes and working conditions from a quality perspective, (2) the staff satisfaction, (3) the efficiency. These experiences, implemented in two BTE for different processes, confirm the applicability and usefulness of these methods to improve working organisations in BTE.

Possible implications of large scale radiation processing of food

NASA Astrophysics Data System (ADS)

Zagórski, Z. P.

Large scale irradiation has been discussed in terms of the participation of processing cost in the final value of the improved product. Another factor has been taken into account and that is the saturation of the market with the new product. In the case of succesful projects the participation of irradiation cost is low, and the demand for the better product is covered. A limited availability of sources makes the modest saturation of the market difficult with all food subjected to correct radiation treatment. The implementation of the preservation of food needs a decided selection of these kinds of food which comply to all conditions i.e. of acceptance by regulatory bodies, real improvement of quality and economy. The last condition prefers the possibility of use of electron beams of low energy. The best fullfilment of conditions for succesful processing is observed in the group of dry food, in expensive spices in particular.

7 CFR 4280.161 - Direct Loan Process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Efficiency Improvements Program Section C. Direct Loans § 4280.161 Direct Loan Process. (a) The Agency will... 7 Agriculture 15 2010-01-01 2010-01-01 false Direct Loan Process. 4280.161 Section 4280.161...; (13) Letter of Conditions, loan agreement, and loan closing process; (14) Processing and servicing of...

RT-CaCCO process: an improved CaCCO process for rice straw by its incorporation with a step of lime pretreatment at room temperature.

PubMed

Shiroma, Riki; Park, Jeung-yil; Al-Haq, Muhammad Imran; Arakane, Mitsuhiro; Ike, Masakazu; Tokuyasu, Ken

2011-02-01

We improved the CaCCO process for rice straw by its incorporation with a step of lime pretreatment at room temperature (RT). We firstly optimized the RT-lime pretreatment for the lignocellulosic part. When the ratio of lime/dry-biomass was 0.2 (w/w), the RT lime-pretreatment for 7-d resulted in an effect on the enzymatic saccharification of cellulose and xylan equivalent to that of the pretreatment at 120°C for 1h. Sucrose, starch and β-1,3-1,4-glucan, which could be often detected in rice straw, were mostly stable under the RT-lime pretreatment condition. Then, the pretreatment condition in the conventional CaCCO process was modified by the adaptation of the optimized RT lime-pretreatment, resulting in significantly better carbohydrate recoveries via enzymatic saccharification than those of the CaCCO process (120°C for 1 h). Thus, the improved CaCCO process (the RT-CaCCO process) could preserve/pretreat the feedstock at RT in a wet form with minimum loss of carbohydrates. Copyright © 2010 Elsevier Ltd. All rights reserved.

How Implementation of TQM and the Development of a Process Improvement Model, Within a Forward Support Battalion, Can Improve Preparation of the Material Condition Status Report (DA Form 2406)

DTIC Science & Technology

1990-12-01

studies for the continuing education of managers new to the TQM approach , for informing vendors of their responsibilities under a changed process, and...Department of Defense (DoD) is adopting a management approach known as Total Quality Management (TQM) in an effort to improve quality and productivity...individuals selected be highly knowledgeable about the operations in their shop or unit. The main function of PATs is to collect and summarize process data for

Simulating pedestrian flow by an improved two-process cellular automaton model

NASA Astrophysics Data System (ADS)

Jin, Cheng-Jie; Wang, Wei; Jiang, Rui; Dong, Li-Yun

In this paper, we study the pedestrian flow with an Improved Two-Process (ITP) cellular automaton model, which is originally proposed by Blue and Adler. Simulations of pedestrian counterflow have been conducted, under both periodic and open boundary conditions. The lane formation phenomenon has been reproduced without using the place exchange rule. We also present and discuss the flow-density and velocity-density relationships of both uni-directional flow and counterflow. By the comparison with the Blue-Adler model, we find the ITP model has higher values of maximum flow, critical density and completely jammed density under different conditions.

Process and catalyst for carbonylating olefins

DOEpatents

Zoeller, Joseph Robert

1998-06-02

Disclosed is an improved catalyst system and process for preparing aliphatic carbonyl compounds such as aliphatic carboxylic acids, alkyl esters of aliphatic carboxylic acids and anhydrides of aliphatic carboxylic acids by carbonylating olefins in the presence of a catalyst system comprising (1) a first component selected from at least one Group 6 metal, i.e., chromium, molybdenum, and/or tungsten and (2) a second component selected from at least one of certain halides and tertiary and quaternary compounds of a Group 15 element, i.e., nitrogen, phosphorus and/or arsenic, and (3) as a third component, a polar, aprotic solvent. The process employing the improved catalyst system is carried out under carbonylating conditions of pressure and temperature discussed herein. The process constitutes and improvement over known processes since it can be carried out at moderate carbonylation conditions without the necessity of using an expensive noble metal catalyst, volatile, toxic materials such as nickel tetracarbonyl, formic acid or a formate ester. Further, the addition of a polar, aprotic solvent to the catalyst system significantly increases, or accelerates, the rate at which the carbonylation takes place.

Business Process Design Method Based on Business Event Model for Enterprise Information System Integration

NASA Astrophysics Data System (ADS)

Kobayashi, Takashi; Komoda, Norihisa

The traditional business process design methods, in which the usecase is the most typical, have no useful framework to design the activity sequence with. Therefore, the design efficiency and quality vary widely according to the designer’s experience and skill. In this paper, to solve this problem, we propose the business events and their state transition model (a basic business event model) based on the language/action perspective, which is the result in the cognitive science domain. In the business process design, using this model, we decide event occurrence conditions so that every event synchronizes with each other. We also propose the design pattern to decide the event occurrence condition (a business event improvement strategy). Lastly, we apply the business process design method based on the business event model and the business event improvement strategy to the credit card issue process and estimate its effect.

Evapotranspiration and land surface process responses to afforestation in western Taiwan: A comparison between dry and wet weather conditions

Treesearch

Yongqiang Liu; L.B. Zhang; L. Hao; Ge Sun; S.-C. Liu

2016-01-01

An afforestation project was initiated in the western plain of Taiwan to convert abandoned farming lands into forests to improve the ecological and environmental conditions. This study was conducted to understand the potential impacts of this land cover change on evapotranspiration (ET) and other land surface processes and the...

Can Schools Meet the Promise of Continuous Improvement?

ERIC Educational Resources Information Center

Elgart, Mark A.

2018-01-01

Continuous improvement is "an embedded behavior within the culture of a school that constantly focuses on the conditions, processes, and practices that will improve teaching and learning." The phrase has been part of the lexicon of school improvement for decades, but real progress is rare. Based on its observations of about 5,000…

Healthcare priority setting in Kenya: a gap analysis applying the accountability for reasonableness framework.

PubMed

Bukachi, Salome A; Onyango-Ouma, Washington; Siso, Jared Maaka; Nyamongo, Isaac K; Mutai, Joseph K; Hurtig, Anna Karin; Olsen, Oystein Evjen; Byskov, Jens

2014-01-01

In resource-poor settings, the accountability for reasonableness (A4R) has been identified as an important advance in priority setting that helps to operationalize fair priority setting in specific contexts. The four conditions of A4R are backed by theory, not evidence, that conformance with them improves the priority setting decisions. This paper describes the healthcare priority setting processes in Malindi district, Kenya, prior to the implementation of A4R in 2008 and evaluates the process for its conformance with the conditions for A4R. In-depth interviews and focus group discussions with key players in the Malindi district health system and a review of key policy documents and national guidelines show that the priority setting process in the district relies heavily on guidelines from the national level, making it more of a vertical, top-down orientation. Multilateral and donor agencies, national government, budgetary requirements, traditions and local culture influence the process. The four conditions of A4R are present within the priority setting process, albeit to varying degrees and referred to by different terms. There exists an opportunity for A4R to provide a guiding approach within which its four conditions can be strengthened and assessed to establish whether conformance helps improve on the priority setting process. Copyright © 2013 John Wiley & Sons, Ltd.

Process, including PSA and membrane separation, for separating hydrogen from hydrocarbons

DOEpatents

Baker, Richard W.; Lokhandwala, Kaaeid A.; He, Zhenjie; Pinnau, Ingo

2001-01-01

An improved process for separating hydrogen from hydrocarbons. The process includes a pressure swing adsorption step, a compression/cooling step and a membrane separation step. The membrane step relies on achieving a methane/hydrogen selectivity of at least about 2.5 under the conditions of the process.

Improved Signal Processing Technique Leads to More Robust Self Diagnostic Accelerometer System

NASA Technical Reports Server (NTRS)

Tokars, Roger; Lekki, John; Jaros, Dave; Riggs, Terrence; Evans, Kenneth P.

2010-01-01

The self diagnostic accelerometer (SDA) is a sensor system designed to actively monitor the health of an accelerometer. In this case an accelerometer is considered healthy if it can be determined that it is operating correctly and its measurements may be relied upon. The SDA system accomplishes this by actively monitoring the accelerometer for a variety of failure conditions including accelerometer structural damage, an electrical open circuit, and most importantly accelerometer detachment. In recent testing of the SDA system in emulated engine operating conditions it has been found that a more robust signal processing technique was necessary. An improved accelerometer diagnostic technique and test results of the SDA system utilizing this technique are presented here. Furthermore, the real time, autonomous capability of the SDA system to concurrently compensate for effects from real operating conditions such as temperature changes and mechanical noise, while monitoring the condition of the accelerometer health and attachment, will be demonstrated.

Improved process conditions for increasing expression of MHC class II protein from a stable Drosophila S2 cell line.

PubMed

Shen, Xiao; Dojcinovic, Danijel; Baldi, Lucia; Hacker, David L; Luescher, Immanuel F; Wurm, Florian M

2018-01-01

To investigate the effects of operational process conditions on expression of MHC class II protein from a stable Drosophila S2 cell line. When the Drosophila S2 cells were grown in vented orbitally shaken TubeSpin bioreactor 600 containers, cell growth was improved three-fold and the yield of recombinant major histocompatibility (MHC) class II protein (HLA-DR1 2xHis ) increased four-fold over the levels observed for the same cells cultivated in roller bottles (RB) without vented caps. Culturing in RB with vented caps while increasing the rotation speed from 6 rpm to 18 rpm also improved cell growth five-fold and protein productivity three-fold which is comparable to the levels observed in the orbitally shaken containers. Protein activity was found to be almost identical between the two vessel systems tested. Optimized cell culture conditions and a more efficient vessel type can enhance gas transfer and mixing and lead to substantial improvement of recombinant product yields from S2 cells.

Development of SiC/SiC composites by PIP in combination with RS

NASA Astrophysics Data System (ADS)

Kotani, Masaki; Kohyama, Akira; Katoh, Yutai

2001-02-01

In order to improve the mechanical performances of SiC/SiC composite, process improvement and modification of polymer impregnation and pyrolysis (PIP) and reaction sintering (RS) process were investigated. The fibrous prepregs were prepared by a polymeric intra-bundle densification technique using Tyranno-SA™ fiber. For inter-bundle matrix, four kinds of process options utilizing polymer pyrolysis and reaction sintering were studied. The process conditions were systematically optimized through fabricating monoliths. Then, SiC/SiC composites were fabricated using optimized inter-bundle matrix slurries in each process for the first inspection of process requirements.

Influence of pH on dynamics of microbial enhanced oil recovery processes using biosurfactant producing Pseudomonas putida: Mathematical modelling and numerical simulation.

PubMed

Sivasankar, P; Suresh Kumar, G

2017-01-01

In present work, the influence of reservoir pH conditions on dynamics of microbial enhanced oil recovery (MEOR) processes using Pseudomonas putida was analysed numerically from the developed mathematical model for MEOR processes. Further, a new strategy to improve the MEOR performance has also been proposed. It is concluded from present study that by reversing the reservoir pH from highly acidic to low alkaline condition (pH 5-8), flow and mobility of displaced oil, displacement efficiency, and original oil in place (OOIP) recovered gets significantly enhanced, resulting from improved interfacial tension (IFT) reduction by biosurfactants. At pH 8, maximum of 26.1% of OOIP was recovered with higher displacement efficiency. The present study introduces a new strategy to increase the recovery efficiency of MEOR technique by characterizing the biosurfactants for IFT min /IFT max values for different pH conditions and subsequently, reversing the reservoir pH conditions at which the IFT min /IFT max value is minimum. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evaluation of different signal processing options in unilateral and bilateral cochlear freedom implant recipients using R-Space background noise.

PubMed

Brockmeyer, Alison M; Potts, Lisa G

2011-02-01

Difficulty understanding in background noise is a common complaint of cochlear implant (CI) recipients. Programming options are available to improve speech recognition in noise for CI users including automatic dynamic range optimization (ADRO), autosensitivity control (ASC), and a two-stage adaptive beamforming algorithm (BEAM). However, the processing option that results in the best speech recognition in noise is unknown. In addition, laboratory measures of these processing options often show greater degrees of improvement than reported by participants in everyday listening situations. To address this issue, Compton-Conley and colleagues developed a test system to replicate a restaurant environment. The R-SPACE™ consists of eight loudspeakers positioned in a 360 degree arc and utilizes a recording made at a restaurant of background noise. The present study measured speech recognition in the R-SPACE with four processing options: standard dual-port directional (STD), ADRO, ASC, and BEAM. A repeated-measures, within-subject design was used to evaluate the four different processing options at two noise levels. Twenty-seven unilateral and three bilateral adult Nucleus Freedom CI recipients. The participants' everyday program (with no additional processing) was used as the STD program. ADRO, ASC, and BEAM were added individually to the STD program to create a total of four programs. Participants repeated Hearing in Noise Test sentences presented at 0 degrees azimuth with R-SPACE restaurant noise at two noise levels, 60 and 70 dB SPL. The reception threshold for sentences (RTS) was obtained for each processing condition and noise level. In 60 dB SPL noise, BEAM processing resulted in the best RTS, with a significant improvement over STD and ADRO processing. In 70 dB SPL noise, ASC and BEAM processing had significantly better mean RTSs compared to STD and ADRO processing. Comparison of noise levels showed that STD and BEAM processing resulted in significantly poorer RTSs in 70 dB SPL noise compared to the performance with these processing conditions in 60 dB SPL noise. Bilateral participants demonstrated a bilateral improvement compared to the better monaural condition for both noise levels and all processing conditions, except ASC in 60 dB SPL noise. The results of this study suggest that the use of processing options that utilize noise reduction, like those available in ASC and BEAM, improve a CI recipient's ability to understand speech in noise in listening situations similar to those experienced in the real world. The choice of the best processing option is dependent on the noise level, with BEAM best at moderate noise levels and ASC best at loud noise levels for unilateral CI recipients. Therefore, multiple noise programs or a combination of processing options may be necessary to provide CI users with the best performance in a variety of listening situations. American Academy of Audiology.

Effect of storage conditions on sensory properties of Bierzo roasted pepper.

PubMed

Casquero, Pedro A; Sanz, Miguel A; Guerra, Marcos

2011-01-15

Roasted pepper is marketed with the European recognition of Protected Geographical Indication 'Pimiento Asado del Bierzo'. The industry needs to prolong the period in which fresh pepper received from farmers is available to be processed, without deteriorating the sensory quality of roasted pepper. The objective of this study was to analyse how different storage conditions affect the sensory quality of roasted pepper. Differences in weight loss among storage conditions did not affect roast yield. Descriptors juice quality, bitterness and spiciness were not influenced by storage conditions in 2006 or 2007, whereas uniformity, skin surface, cohesiveness and smokiness were influenced by storage conditions in both years. Overall quality was better when pepper was stored for 5 days at 18 °C or for 10 days at 8 °C. The quality of roasted pepper was affected positively by storage conditions in terms of colour and uniformity, which were improved, and hardness, which was reduced. Newly roasted samples, on the other hand, obtained the lowest quality values. Therefore storage of pepper for up to 10 days was useful not only to extend the time of roasted pepper processing for companies but also to improve the sensory quality of roasted pepper without decreasing the roast yield of processed pepper. Copyright © 2010 Society of Chemical Industry.

Improving wait times to care for individuals with multimorbidities and complex conditions using value stream mapping.

PubMed

Sampalli, Tara; Desy, Michel; Dhir, Minakshi; Edwards, Lynn; Dickson, Robert; Blackmore, Gail

2015-04-05

Recognizing the significant impact of wait times for care for individuals with complex chronic conditions, we applied a LEAN methodology, namely - an adaptation of Value Stream Mapping (VSM) to meet the needs of people with multiple chronic conditions and to improve wait times without additional resources or funding. Over an 18-month time period, staff applied a patient-centric approach that included LEAN methodology of VSM to improve wait times to care. Our framework of evaluation was grounded in the needs and perspectives of patients and individuals waiting to receive care. Patient centric views were obtained through surveys such as Patient Assessment of Chronic Illness Care (PACIC) and process engineering based questions. In addition, LEAN methodology, VSM was added to identify non-value added processes contributing to wait times. The care team successfully reduced wait times to 2 months in 2014 with no wait times for care anticipated in 2015. Increased patient engagement and satisfaction are also outcomes of this innovative initiative. In addition, successful transformations and implementation have resulted in resource efficiencies without increase in costs. Patients have shown significant improvements in functional health following Integrated Chronic Care Service (ICCS) intervention. The methodology will be applied to other chronic disease management areas in Capital Health and the province. Wait times to care in the management of multimoribidities and other complex conditions can add a significant burden not only on the affected individuals but also on the healthcare system. In this study, a novel and modified LEAN methodology has been applied to embed the voice of the patient in care delivery processes and to reduce wait times to care in the management of complex chronic conditions. © 2015 by Kerman University of Medical Sciences.

Fired heater for coal liquefaction process

DOEpatents

Ying, David H. S.; McDermott, Wayne T.; Givens, Edwin N.

1985-01-01

A fired heater for a coal liquefaction process is operated under conditions to maximize the slurry slug frequency and thereby improve the heat transfer efficiency. The operating conditions controlled are (1) the pipe diameter and pipe arrangement, (2) the minimum coal/solvent slurry velocity, (3) the maximum gas superficial velocity, and (4) the range of the volumetric flow velocity ratio of gas to coal/solvent slurry.

Conditioning biomass for microbial growth

DOEpatents

Bodie, Elizabeth A; England, George

2015-03-31

The present invention relates to methods for improving the yield of microbial processes that use lignocellulose biomass as a nutrient source. The methods comprise conditioning a composition comprising lignocellulose biomass with an enzyme composition that comprises a phenol oxidizing enzyme. The conditioned composition can support a higher rate of growth of microorganisms in a process. In one embodiment, a laccase composition is used to condition lignocellulose biomass derived from non-woody plants, such as corn and sugar cane. The invention also encompasses methods for culturing microorganisms that are sensitive to inhibitory compounds in lignocellulose biomass. The invention further provides methods of making a product by culturing the production microorganisms in conditioned lignocellulose biomass.

Effects of raw material extrusion and steam conditioning on feed pellet quality and nutrient digestibility of growing meat rabbits.

PubMed

Liao, Kuoyao; Cai, Jingyi; Shi, Zhujun; Tian, Gang; Yan, Dong; Chen, Delin

2017-06-01

This study was conducted to investigate the effects of raw material extrusion and steam conditioning on feed pellet quality and nutrient digestibility of growing meat rabbits, in order to determine appropriate rabbit feed processing methods and processing parameters. In Exp. 1, an orthogonal design was adopted. Barrel temperature, material moisture content and feed rate were selected as test factors, and acid detergent fiber (ADF) content was selected as an evaluation index to research the optimum extrusion parameters. In Exp. 2, a two-factor design was adopted. Four kinds of rabbit feeds were processed and raw material extrusion adopted optimum extrusion parameters of Exp. 1. A total of 40 healthy and 42-day-old rabbits with similar weight were used in a randomized design, which consisted of 4 groups and 10 replicates in each group (1 rabbits in each replicate). The adaptation period lasted for 7 d, and the digestion trial lasted for 4 d. The results showed as follows: 1) ADF was significantly affected by barrel temperature ( P  < 0.05); the optimum extrusion parameters were barrel temperature 125 °C, moisture content 16% and feed rate 9 Hz. 2) Raw material extrusion and steam conditioning both significantly decreased powder percentage, pulverization ratio and protein solubility ( P  < 0.05), significantly improved hardness and starch gelatinization degree of rabbit feed ( P  < 0.05). They both had significant interaction effects on the processing quality of rabbit feed ( P  < 0.05). 3) Extrusion significantly improved the apparent digestibility of dry matter and total energy ( P  < 0.05). Extrusion and steam conditioning both significantly improved the apparent digestibility of crude fiber (CF), ADF and NDF ( P  < 0.05), but they had no interaction effects on the apparent digestibility of rabbit feed. Thus, using extrusion and steam conditioning technology at the same time in the weaning rabbits feed processing can improve the pellet quality and nutrient apparent digestibility of rabbit feed.

Two-Microphone Spatial Filtering Improves Speech Reception for Cochlear-Implant Users in Reverberant Conditions With Multiple Noise Sources

PubMed Central

2014-01-01

This study evaluates a spatial-filtering algorithm as a method to improve speech reception for cochlear-implant (CI) users in reverberant environments with multiple noise sources. The algorithm was designed to filter sounds using phase differences between two microphones situated 1 cm apart in a behind-the-ear hearing-aid capsule. Speech reception thresholds (SRTs) were measured using a Coordinate Response Measure for six CI users in 27 listening conditions including each combination of reverberation level (T60 = 0, 270, and 540 ms), number of noise sources (1, 4, and 11), and signal-processing algorithm (omnidirectional response, dipole-directional response, and spatial-filtering algorithm). Noise sources were time-reversed speech segments randomly drawn from the Institute of Electrical and Electronics Engineers sentence recordings. Target speech and noise sources were processed using a room simulation method allowing precise control over reverberation times and sound-source locations. The spatial-filtering algorithm was found to provide improvements in SRTs on the order of 6.5 to 11.0 dB across listening conditions compared with the omnidirectional response. This result indicates that such phase-based spatial filtering can improve speech reception for CI users even in highly reverberant conditions with multiple noise sources. PMID:25330772

Method to Prepare Processable Polyimides with Non-Reactive Endgroups Using 1,3-bis(3-Aminophenoxy) Benzene

NASA Technical Reports Server (NTRS)

Jensen, Brian J. (Inventor)

2000-01-01

Polyimide copolymers were obtained containing 1,3-bis(3-aminophenoxy)benzene (APB) and other diamines and dianhydrides and terminating with the appropriate amount of a non-reactive endcapper, such as phthalic anhydride. Homopolymers containing only other diamines and dianhydrides which are not processable under conditions described previously can be made processable by incorporating various amounts of APB, depending on the chemical structures of the diamines and dianhydrides used. Polyimides that are more rigid in nature require more APB to impart processability than polyimides that are less rigid in nature. The copolymers that result from using APB to enhance processability have a unique combination of properties including excellent thin film properties, low pressure processing (200 psi and below), improved toughness, improved solvent resistance, improved adhesive properties, improved composite mechanical properties, long term melt stability (several hours at 390 C), and lower melt viscosities.

Method To Prepare Processable Polyimides With Reactive Endogroups Using 1,3-bis(3-aminophenoxy)benzene

NASA Technical Reports Server (NTRS)

Jensen, Brian J. (Inventor)

2001-01-01

Polyimide copolymers were obtained containing 1,3-bis(3-aminophenoxy)benzene (APB) and other diamines and dianhydrides and terminating with the appropriate amount of a non-reactive endcapper, such as phthalic anhydride. Homopolymers containing only other diamines and dianhydrides which are not processable under conditions described previously can be made processable by incorporating various amounts of APB, depending on the chemical structures of the diamines and dianhydrides used. Polyimides that are more rigid in nature require more APB to impart processability than polyimides that are less rigid in nature. The copolymers that result from using APB to enhance processability have a unique combination of properties including excellent thin film properties, low pressure processing (200 psi and below), improved toughness, improved solvent resistance, improved adhesive properties, improved composite mechanical properties, long term melt stability (several hours at 390 C), and lower melt viscosities.

Costs of the War in Colombia: A Strategic Vision of the End of the Conflict

DTIC Science & Technology

2005-03-18

February 2002. That date marked the termination of a new peace process generated under the former government of President Andres Pastrana. The above...conflict. The Colombian elite no longer offer polite lip service to the peace process , they know the insurgents must be defeated once an for all. Almost...condition for a successful peace process and to rebuild the nation and improve conditions. It will note the recent example of El Salvador, where post

Numerical and experimental analysis of a ducted propeller designed by a fully automated optimization process under open water condition

NASA Astrophysics Data System (ADS)

Yu, Long; Druckenbrod, Markus; Greve, Martin; Wang, Ke-qi; Abdel-Maksoud, Moustafa

2015-10-01

A fully automated optimization process is provided for the design of ducted propellers under open water conditions, including 3D geometry modeling, meshing, optimization algorithm and CFD analysis techniques. The developed process allows the direct integration of a RANSE solver in the design stage. A practical ducted propeller design case study is carried out for validation. Numerical simulations and open water tests are fulfilled and proved that the optimum ducted propeller improves hydrodynamic performance as predicted.

An Electrochemical Processing Strategy for Improving Tribological Performance of Aisi 316 Stainless Steel Under Grease Lubrication

NASA Astrophysics Data System (ADS)

Zou, Jiaojuan; Li, Maolin; Lin, Naiming; Zhang, Xiangyu; Qin, Lin; Tang, Bin

2014-12-01

In order to improve the tribological performance of AISI 316 stainless steel (316 SS) under grease lubrication, electrochemical processing was conducted on it to obtain a rough (surface texturing-like) surface by making use of the high sensitivity of austenitic stainless steel to pitting corrosion in Cl--rich environment. Numerous corrosion pits or micro-ditches acted as micro-reservoirs on the obtained surface. While the grease could offer consistent lubrication, and then improve the tribological performance of 316 SS. Tribological behaviors of raw 316 SS and the treated sample were measured using a reciprocating type tribometer sliding against GCr15 steel counterpart under dry and grease lubrication conditions. The results showed that the mass losses of the two samples were in the same order of magnitude, and the raw sample exhibited lower friction coefficient in dry sliding. When the tests were conducted under grease lubrication condition, the friction coefficients and mass losses of the treated sample were far lower than those of the raw 316 SS. The tribological performance of 316 SS under grease lubrication was drastically improved after electrochemical processing.

Improving titer while maintaining quality of final formulated drug substance via optimization of CHO cell culture conditions in low-iron chemically defined media.

PubMed

Xu, Jianlin; Rehmann, Matthew S; Xu, Xuankuo; Huang, Chao; Tian, Jun; Qian, Nan-Xin; Li, Zheng Jian

2018-04-01

During biopharmaceutical process development, it is important to improve titer to reduce drug manufacturing costs and to deliver comparable quality attributes of therapeutic proteins, which helps to ensure patient safety and efficacy. We previously reported that relative high-iron concentrations in media increased titer, but caused unacceptable coloration of a fusion protein during early-phase process development. Ultimately, the fusion protein with acceptable color was manufactured using low-iron media, but the titer decreased significantly in the low-iron process. Here, long-term passaging in low-iron media is shown to significantly improve titer while maintaining acceptable coloration during late-phase process development. However, the long-term passaging also caused a change in the protein charge variant profile by significantly increasing basic variants. Thus, we systematically studied the effect of media components, seed culture conditions, and downstream processing on productivity and quality attributes. We found that removing β-glycerol phosphate (BGP) from basal media reduced basic variants without affecting titer. Our goals for late-phase process development, improving titer and matching quality attributes to the early-phase process, were thus achieved by prolonging seed culture age and removing BGP. This process was also successfully scaled up in 500-L bioreactors. In addition, we demonstrated that higher concentrations of reactive oxygen species were present in the high-iron Chinese hamster ovary cell cultures compared to that in the low-iron cultures, suggesting a possible mechanism for the drug substance coloration caused by high-iron media. Finally, hypotheses for the mechanisms of titer improvement by both high-iron and long-term culture are discussed.

Operation of the solvent-refined-coal pilot plant, Wilsonville, Alabama. Annual technical report, January-December 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, H.E.

1981-08-01

The plant was in operation for the equivalent of 247 days, an on-stream factor of 67.7%. Kentucky 9 coals from the Lafayette, Dotiki and Fies mines were processed. During 1980, the operating conditions and equipment were adjusted to evaluate potential process improvements. These experiments produced significant results in the following areas: Operating V103 High Pressure Separator in the hot mode; varying T102 Vacuum Column operating temperature; adding light SRC (LSRC), a product of the third stage of the Critical Solvent Deashing (CSD) unit, to the process solvent; investigating the effects of the chlorine content of the feed coal on corrosionmore » in the process vessels; evaluating the effects of adding sodium carbonate on corrosion rates; operating under conditions of low severity; i.e., low reactor temperature and long residence time; and testing an alternate CSD deashing solvent. A series of simulation runs investigating the design operating conditions for a planned 6000 ton per day SRC-I demonstation plant were also completed. Numerous improvements were made in the CSD processing area, and the components for a hydrotreating unit were installed.« less

Portable Body Temperature Conditioner

DTIC Science & Technology

2013-12-01

thermal manikin. This research will identify specific design improvements to be implemented in a reiterative process , ultimately leading to an...activity in hot environmental conditions. Studies have shown that lowering the patient’s core body temperature rapidly to 38oC improves complications and...further attempts to hire a second technician, during the past year (Year 2) UNSOM began the process of hiring a bio-heat transfer engineering expert to

The exercise and affect relationship: evidence for the dual-mode model and a modified opponent process theory.

PubMed

Markowitz, Sarah M; Arent, Shawn M

2010-10-01

This study examined the relationship between exertion level and affect using the framework of opponent-process theory and the dual-mode model, with the Activation-Deactivation Adjective Checklist and the State Anxiety Inventory among 14 active and 14 sedentary participants doing 20 min of treadmill exercise at speeds of 5% below, 5% above, and at lactate threshold (LT). We found a significant effect of time, condition, Time × Condition, and Time × Group, but no group, Group × Condition, or Time × Group × Condition effects, such that the 5% above LT condition produced a worsening of affect in-task compared with all other conditions whereas, across conditions, participants experienced in-task increases in energy and tension, and in-task decreases in tiredness and calmness relative to baseline. Posttask, participants experienced mood improvement (decreased tension, anxiety, and increased calmness) across conditions, with a 30-min delay in the above LT condition. These results partially support the dual-mode model and a modified opponent-process theory.

Improving the compression dewatering of sewage sludge through bioacidification conditioning driven by Acidithiobacillus ferrooxidans: dewatering rate vs. dewatering extent.

PubMed

Lu, Yi; Zhang, Chunmei; Zheng, Guanyu; Zhou, Lixiang

2018-04-22

Prior to mechanical dewatering, sludge conditioning is indispensable to reduce the difficulty of sludge treatment and disposal. The effect of bioacidification conditioning driven by Acidithiobacillus ferrooxidans LX5 on the dewatering rate and extent of sewage sludge during compression dewatering process was investigated in this study. The results showed that the bioacidification of sludge driven by A. ferrooxidans LX5 simultaneously improved both the sludge dewatering rate and extent, which was not attained by physical/chemical conditioning approaches, including ultrasonication, microwave, freezing/thawing, or by adding the chemical conditioner cationic polyacrylamide (CPAM). During the bioacidification of sludge, the decrease in sludge pH induced the damage of sludge microbial cell structures, which enhanced the dewatering extent of sludge, and the added Fe 2+ and the subsequent bio-oxidized Fe 3+ effectively flocculated the damaged sludge flocs to improve the sludge dewatering rate. In the compression dewatering process consisting of filtration and expression stages, high removal of moisture and a short dewatering time were achieved during the filtration stage and the expression kinetics were also improved because of the high elasticity of sludge cake and the rapid creeping of the aggregates within the sludge cake. In addition, the usefulness of bioacidification driven by A. ferrooxidans LX5 in improving the compression dewatering of sewage sludge could not be attained by the chemical treatment of sludge through pH modification and Fe 3+ addition. Therefore, the bioacidification of sludge driven by A. ferrooxidans LX5 is an effective conditioning method to simultaneously improve the rate and extent of compression dewatering of sewage sludge.

Mobile geographic information system (GIS) solution for pavement condition surveys.

DOT National Transportation Integrated Search

2012-06-28

This report discusses the design and implementation of a software-based solution that will improve the data collection processes during the Pavement Condition Surveys (PCS) conducted by the State Materials Office (SMO) of the Florida Department of Tr...

Process-Improvement Cost Model for the Emergency Department.

PubMed

Dyas, Sheila R; Greenfield, Eric; Messimer, Sherri; Thotakura, Swati; Gholston, Sampson; Doughty, Tracy; Hays, Mary; Ivey, Richard; Spalding, Joseph; Phillips, Robin

2015-01-01

The objective of this report is to present a simplified, activity-based costing approach for hospital emergency departments (EDs) to use with Lean Six Sigma cost-benefit analyses. The cost model complexity is reduced by removing diagnostic and condition-specific costs, thereby revealing the underlying process activities' cost inefficiencies. Examples are provided for evaluating the cost savings from reducing discharge delays and the cost impact of keeping patients in the ED (boarding) after the decision to admit has been made. The process-improvement cost model provides a needed tool in selecting, prioritizing, and validating Lean process-improvement projects in the ED and other areas of patient care that involve multiple dissimilar diagnoses.

Electrocoagulation pretreatment of wet-spun acrylic fibers manufacturing wastewater to improve its biodegradability.

PubMed

Gong, Chenhao; Zhang, Zhongguo; Li, Haitao; Li, Duo; Wu, Baichun; Sun, Yuwei; Cheng, Yanjun

2014-06-15

The electrocoagulation (EC) process was used to pretreat wastewater from the manufacture of wet-spun acrylic fibers, and the effects of varying the operating parameters, including the electrode area/wastewater volume (A/V) ratio, current density, interelectrode distance and pH, on the EC treatment process were investigated. About 44% of the total organic carbon was removed using the optimal conditions in a 100 min procedure. The optimal conditions were a current density of 35.7 mA cm(-2), an A/V ratio of 0.28 cm(-1), a pH of 5, and an interelectrode distance of 0.8 cm. The biodegradability of the contaminants in the treated water was improved by the EC treatment (using the optimal conditions), increasing the five-day biological oxygen demand/chemical oxygen demand ratio to 0.35, which could improve the effectiveness of subsequent biological treatments. The improvement in the biodegradability of the contaminants in the wastewater was attributed to the removal and degradation of aromatic organic compounds, straight-chain paraffins, and other organic compounds, which we identified using gas chromatography-mass spectrometry and Fourier transform infrared spectroscopy. The EC process was proven to be an effective alternative pretreatment for wastewater from the manufacture of wet-spun acrylic fibers, prior to biological treatments. Copyright © 2014 Elsevier B.V. All rights reserved.

Improving the efficiency of cognitive-behavioural therapy by using formal client feedback.

PubMed

Janse, Pauline D; De Jong, Kim; Van Dijk, Maarten K; Hutschemaekers, Giel J M; Verbraak, Marc J P M

2017-09-01

Feedback from clients on their view of progress and the therapeutic relationship can improve effectiveness and efficiency of psychological treatments in general. However, what the added value is of client feedback specifically within cognitive-behavioural therapy (CBT), is not known. Therefore, the extent to which the outcome of CBT can be improved is investigated by providing feedback from clients to therapists using the Outcome Rating Scale (ORS) and Session Rating Scale (SRS). Outpatients (n = 1006) of a Dutch mental health organization either participated in the "treatment as usual" (TAU) condition, or in Feedback condition of the study. Clients were invited to fill in the ORS and SRS and in the Feedback condition therapists were asked to frequently discuss client feedback. Outcome on the SCL-90 was only improved specifically with mood disorders in the Feedback condition. Also, in the Feedback condition, in terms of process, the total number of required treatment sessions was on average two sessions fewer. Frequently asking feedback from clients using the ORS/SRS does not necessarily result in a better treatment outcome in CBT. However, for an equal treatment outcome significantly fewer sessions are needed within the Feedback condition, thus improving efficiency of CBT.

Medicaid Program; Mechanized Claims Processing and Information Retrieval Systems (90/10). Final rule.

PubMed

2015-12-04

This final rule will extend enhanced funding for Medicaid eligibility systems as part of a state's mechanized claims processing system, and will update conditions and standards for such systems, including adding to and updating current Medicaid Management Information Systems (MMIS) conditions and standards. These changes will allow states to improve customer service and support the dynamic nature of Medicaid eligibility, enrollment, and delivery systems.

Coaching to vision versus coaching to improvement needs: a preliminary investigation on the differential impacts of fostering positive and negative emotion during real time executive coaching sessions

PubMed Central

Howard, Anita R.

2015-01-01

Drawing on intentional change theory (ICT; Boyatzis, 2006), this study examined the differential impact of inducing coaching recipients’ vision/positive emotion versus improvement needs/negative emotion during real time executive coaching sessions. A core aim of the study was to empirically test two central ICT propositions on the effects of using the coached person’s Positive Emotional Attractor (vision/PEA) versus Negative Emotional Attractor (improvement needs/NEA) as the anchoring framework of a onetime, one-on-one coaching session on appraisal of 360° feedback and discussion of possible change goals. Eighteen coaching recipients were randomly assigned to two coaching conditions, the coaching to vision/PEA condition and the coaching to improvement needs/NEA condition. Two main hypotheses were tested. Hypothesis1 predicted that participants in the vision/PEA condition would show higher levels of expressed positive emotion during appraisal of 360° feedback results and discussion of change goals than recipients in the improvement needs/NEA condition. Hypothesis2 predicted that vision/PEA participants would show lower levels of stress immediately after the coaching session than improvement needs/NEA participants. Findings showed that coaching to vision/the PEA fostered significantly lower levels of expressed negative emotion and anger during appraisal of 360° feedback results as compared to coaching to improvements needs/the NEA. Vision-focused coaching also fostered significantly greater exploration of personal passions and future desires, and more positive engagement during 360° feedback appraisal. No significant differences between the two conditions were found in emotional processing during discussion of change goals or levels of stress immediately after the coaching session. Current findings suggest that vision/PEA arousal versus improvement needs/NEA arousal impact the coaching process in quite different ways; that the coach’s initial framing of the session predominantly in the PEA (or, alternatively, predominantly in the NEA) fosters emotional processing that is driven by this initial framing; and that both the PEA (and associated positive emotions) and NEA (and associated negative emotions) play an important and recurrent role in shaping the change process. Further study on these outcomes will enable researchers to shed more light on the differential impact of the PEA versus NEA on intentional change, and how to leverage the benefits of both emotional attractors. Findings also suggest that coaches can benefit from better understanding the importance of tapping intrinsic motivation and personal passions through coaching to vision/the PEA. Coaches additionally may benefit from better understanding how to leverage the long-term advantages, and restorative benefits, of positive emotions during coaching engagements. The findings also highlight coaches’ need to appreciate the impact of timing effects on coaching intentional change, and how coaches can play a critical role in calibrating the pace and focus of work on intentional change. Early arousal of the coachee’s PEA, accompanied by recurrent PEA–NEA induction, may help coachees be/become more creative, optimistic, and resilient during a given change process. Overall, primary focus on vision/PEA and secondary focus on improvement needs/NEA may better equip coaches and coaching recipients to work together on building robust learning, development, and change. Keywords-133pt executive coaching, vision, improvement needs, positive emotion, negative emotion, emotional appraisal, intentional change, positive psychology PMID:25964768

Coaching to vision versus coaching to improvement needs: a preliminary investigation on the differential impacts of fostering positive and negative emotion during real time executive coaching sessions.

PubMed

Howard, Anita R

2015-01-01

Drawing on intentional change theory (ICT; Boyatzis, 2006), this study examined the differential impact of inducing coaching recipients' vision/positive emotion versus improvement needs/negative emotion during real time executive coaching sessions. A core aim of the study was to empirically test two central ICT propositions on the effects of using the coached person's Positive Emotional Attractor (vision/PEA) versus Negative Emotional Attractor (improvement needs/NEA) as the anchoring framework of a onetime, one-on-one coaching session on appraisal of 360° feedback and discussion of possible change goals. Eighteen coaching recipients were randomly assigned to two coaching conditions, the coaching to vision/PEA condition and the coaching to improvement needs/NEA condition. Two main hypotheses were tested. Hypothesis1 predicted that participants in the vision/PEA condition would show higher levels of expressed positive emotion during appraisal of 360° feedback results and discussion of change goals than recipients in the improvement needs/NEA condition. Hypothesis2 predicted that vision/PEA participants would show lower levels of stress immediately after the coaching session than improvement needs/NEA participants. Findings showed that coaching to vision/the PEA fostered significantly lower levels of expressed negative emotion and anger during appraisal of 360° feedback results as compared to coaching to improvements needs/the NEA. Vision-focused coaching also fostered significantly greater exploration of personal passions and future desires, and more positive engagement during 360° feedback appraisal. No significant differences between the two conditions were found in emotional processing during discussion of change goals or levels of stress immediately after the coaching session. Current findings suggest that vision/PEA arousal versus improvement needs/NEA arousal impact the coaching process in quite different ways; that the coach's initial framing of the session predominantly in the PEA (or, alternatively, predominantly in the NEA) fosters emotional processing that is driven by this initial framing; and that both the PEA (and associated positive emotions) and NEA (and associated negative emotions) play an important and recurrent role in shaping the change process. Further study on these outcomes will enable researchers to shed more light on the differential impact of the PEA versus NEA on intentional change, and how to leverage the benefits of both emotional attractors. Findings also suggest that coaches can benefit from better understanding the importance of tapping intrinsic motivation and personal passions through coaching to vision/the PEA. Coaches additionally may benefit from better understanding how to leverage the long-term advantages, and restorative benefits, of positive emotions during coaching engagements. The findings also highlight coaches' need to appreciate the impact of timing effects on coaching intentional change, and how coaches can play a critical role in calibrating the pace and focus of work on intentional change. Early arousal of the coachee's PEA, accompanied by recurrent PEA-NEA induction, may help coachees be/become more creative, optimistic, and resilient during a given change process. Overall, primary focus on vision/PEA and secondary focus on improvement needs/NEA may better equip coaches and coaching recipients to work together on building robust learning, development, and change. Keywords-133pt executive coaching, vision, improvement needs, positive emotion, negative emotion, emotional appraisal, intentional change, positive psychology.

An adaptive management process for forest soil conservation.

Treesearch

Michael P. Curran; Douglas G. Maynard; Ronald L. Heninger; Thomas A. Terry; Steven W. Howes; Douglas M. Stone; Thomas Niemann; Richard E. Miller; Robert F. Powers

2005-01-01

Soil disturbance guidelines should be based on comparable disturbance categories adapted to specific local soil conditions, validated by monitoring and research. Guidelines, standards, and practices should be continually improved based on an adaptive management process, which is presented in this paper. Core components of this process include: reliable monitoring...

7 CFR 1599.4 - Application process.

Code of Federal Regulations, 2012 CFR

2012-01-01

... associations, community infrastructure, and health, nutrition, water and sanitation conditions; (3) Information... improvements in the learning environment; (iii) Improved maternal, child and student health and nutrition; (iv... OF AGRICULTURE McGOVERN-DOLE INTERNATIONAL FOOD FOR EDUCATION AND CHILD NUTRITION PROGRAM § 1599.4...

7 CFR 1599.4 - Application process.

Code of Federal Regulations, 2014 CFR

2014-01-01

... associations, community infrastructure, and health, nutrition, water and sanitation conditions; (3) Information... improvements in the learning environment; (iii) Improved maternal, child and student health and nutrition; (iv... OF AGRICULTURE McGOVERN-DOLE INTERNATIONAL FOOD FOR EDUCATION AND CHILD NUTRITION PROGRAM § 1599.4...

7 CFR 1599.4 - Application process.

Code of Federal Regulations, 2011 CFR

2011-01-01

... associations, community infrastructure, and health, nutrition, water and sanitation conditions; (3) Information... improvements in the learning environment; (iii) Improved maternal, child and student health and nutrition; (iv... OF AGRICULTURE McGOVERN-DOLE INTERNATIONAL FOOD FOR EDUCATION AND CHILD NUTRITION PROGRAM § 1599.4...

7 CFR 1599.4 - Application process.

Code of Federal Regulations, 2013 CFR

2013-01-01

... associations, community infrastructure, and health, nutrition, water and sanitation conditions; (3) Information... improvements in the learning environment; (iii) Improved maternal, child and student health and nutrition; (iv... OF AGRICULTURE McGOVERN-DOLE INTERNATIONAL FOOD FOR EDUCATION AND CHILD NUTRITION PROGRAM § 1599.4...

Influence of operating conditions on the optimum design of electric vehicle battery cooling plates

NASA Astrophysics Data System (ADS)

Jarrett, Anthony; Kim, Il Yong

2014-01-01

The efficiency of cooling plates for electric vehicle batteries can be improved by optimizing the geometry of internal fluid channels. In practical operation, a cooling plate is exposed to a range of operating conditions dictated by the battery, environment, and driving behaviour. To formulate an efficient cooling plate design process, the optimum design sensitivity with respect to each boundary condition is desired. This determines which operating conditions must be represented in the design process, and therefore the complexity of designing for multiple operating conditions. The objective of this study is to determine the influence of different operating conditions on the optimum cooling plate design. Three important performance measures were considered: temperature uniformity, mean temperature, and pressure drop. It was found that of these three, temperature uniformity was most sensitive to the operating conditions, especially with respect to the distribution of the input heat flux, and also to the coolant flow rate. An additional focus of the study was the distribution of heat generated by the battery cell: while it is easier to assume that heat is generated uniformly, by using an accurate distribution for design optimization, this study found that cooling plate performance could be significantly improved.

Understanding dynamic pattern and process across spatial scales in river systems using simultaneous deployments of in situ sensors

NASA Astrophysics Data System (ADS)

Wollheim, W. M.; Mulukutla, G.; Cook, C.; Carey, R. O.

2014-12-01

Biogeochemical conditions throughout aquatic landscapes are spatially varied and temporally dynamic due to interactions of upstream land use, climate, hydrologic responses, and internal aquatic processes. One of the key goals in aquatic ecosystem ecology is to parse the upstream influences of terrestrial and aquatic processes on local conditions, which becomes progressively more difficult as watershed size increases and as processes are altered by diverse human activities. Simultaneous deployments of high frequency, in situ aquatic sensors for multiple constituents (e.g. NO3-N, CDOM, turbidity, conductivity, D.O., water temperature, along with flow) offer a new approach for understanding patterns along the aquatic continuum. For this talk, we explore strategies for deployments within single watersheds to improve understanding of terrestrial and aquatic processes. We address applications regarding mobilization of non-point nutrient sources across temporal scales, interactions with land use and watershed size, and the importance of aquatic processes. We also explore ways in which simultaneous sensor deployments can be designed to improve parameterization and testing of river network biogeochemical models. We will provide several specific examples using conductivity, nitrate and carbon from ongoing sensor deployments in New England, USA. We expect that improved deployments of sensors and sensor networks will benefit the management of critical freshwater resources.

Metallurgical characterization of a new nickel-titanium wire for rotary endodontic instruments.

PubMed

Alapati, Satish B; Brantley, William A; Iijima, Masahiro; Clark, William A T; Kovarik, Libor; Buie, Caesar; Liu, Jie; Ben Johnson, William

2009-11-01

A novel thermomechanical processing procedure has been developed that yields a superelastic (SE) nickel-titanium (NiTi) wire (M-Wire) that laboratory testing shows has improved mechanical properties compared with conventional SE austenitic NiTi wires used for manufacture of rotary instruments. The objective of this study was to determine the origin of the improved mechanical properties. Specimens from 2 batches of M-Wire prepared under different processing conditions and from 1 batch of standard-processed SE wire for rotary instruments were examined by scanning transmission electron microscopy, temperature-modulated differential scanning calorimetry, micro-x-ray diffraction, and scanning electron microscopy with x-ray energy-dispersive spectrometric analyses. The processing for M-Wire yields a microstructure containing martensite, that the proportions of NiTi phases depend on processing conditions, and that the microstructure exhibits pronounced evidence of alloy strengthening. The presence of Ti(2)Ni precipitates in both microstructures indicates that M-Wire and the conventional SE wire for rotary instruments are titanium-rich.

Improving Preschoolers’ Arithmetic through Number Magnitude Training: The Impact of Non-Symbolic and Symbolic Training

PubMed Central

2016-01-01

The numerical cognition literature offers two views to explain numerical and arithmetical development. The unique-representation view considers the approximate number system (ANS) to represent the magnitude of both symbolic and non-symbolic numbers and to be the basis of numerical learning. In contrast, the dual-representation view suggests that symbolic and non-symbolic skills rely on different magnitude representations and that it is the ability to build an exact representation of symbolic numbers that underlies math learning. Support for these hypotheses has come mainly from correlative studies with inconsistent results. In this study, we developed two training programs aiming at enhancing the magnitude processing of either non-symbolic numbers or symbolic numbers and compared their effects on arithmetic skills. Fifty-six preschoolers were randomly assigned to one of three 10-session-training conditions: (1) non-symbolic training (2) symbolic training and (3) control training working on story understanding. Both numerical training conditions were significantly more efficient than the control condition in improving magnitude processing. Moreover, symbolic training led to a significantly larger improvement in arithmetic than did non-symbolic training and the control condition. These results support the dual-representation view. PMID:27875540

Ergonomics and Kaizen as strategies for competitiveness: a theoretical and practical in an automotive industry.

PubMed

Vieira, Leandro; Balbinotti, Giles; Varasquin, Adriano; Gontijo, Leila

2012-01-01

With increased international competitiveness in the automotive industry, came the concern of the companies save costs and lower production costs. For this purpose many ways are designed to reduce costs and waste of raw materials and reduce activities that do not aggregate value to manufacturing processes. In the early XVII appears the manufacturing system, which processes were hard with little concern for the health and safety of employees and conditions of the workplace. After the advent of the production system called lean manufacturing, a new paradigm in terms of production system capable of providing high levels of productivity and quality. It is based on waste elimination that occur during the production process. After began a new way of thinking, creating a culture of continuous improvement and lean process with no waste and reducing costs, without neglecting the welfare worker and improving the conditions of their work environment. This paper presents a reflection on the application of ergonomics in a lean production system of an automotive industry, using methodology based on the Kaizen (Continuous Improvement) to gain performance and improving the conditions of the workplace, also will be presented with positive and negative points in using this methodology in relation to ergonomics. The research will be conducted by collecting data 'in loco' and interviews with workers. Some studies show that in companies that are lean system and using the methodology of Kaizen, the results of product quality, levels of absenteeism and accidents are better than those obtained in companies that do not apply the same concept.

The effectiveness of CCDSR learning model to improve skills of creating lesson plan and worksheet science process skill (SPS) for pre-service physics teacher

NASA Astrophysics Data System (ADS)

Limatahu, I.; Sutoyo, S.; Wasis; Prahani, B. K.

2018-03-01

In the previous research, CCDSR (Condition, Construction, Development, Simulation, and Reflection) learning model has been developed to improve science process skills for pre-service physics teacher. This research is aimed to analyze the effectiveness of CCDSR learning model towards the improvement skills of creating lesson plan and worksheet of Science Process Skill (SPS) for pre-service physics teacher in academic year 2016/2017. This research used one group pre-test and post-test design on 12 pre-service physics teacher at Physics Education, University of Khairun. Data collection was conducted through test and observation. Creating lesson plan and worksheet SPS skills of pre-service physics teacher measurement were conducted through Science Process Skill Evaluation Sheet (SPSES). The data analysis technique was done by Wilcoxon t-test and n-gain. The CCDSR learning model consists of 5 phases, including (1) Condition, (2) Construction, (3) Development, (4) Simulation, and (5) Reflection. The results showed that there was a significant increase in creating lesson plan and worksheet SPS skills of pre-service physics teacher at α = 5% and n-gain average of moderate category. Thus, the CCDSR learning model is effective for improving skills of creating lesson plan and worksheet SPS for pre-service physics teacher.

Improving emerging organic compound degradation through chaotic advection in a Managed Aquifer Recharge: the case of benzotriazoles

NASA Astrophysics Data System (ADS)

Rodriguez-Escales, P.; Drechsel, J.; Fernandez-Garcia, D.; Sanchez-Vila, X.

2016-12-01

Improving emerging compound degradation in groundwater is still a challenge. The coupling of Managed Aquifer Recharge (MAR) with soil aquifer remediation (SAR) through a reactive layer placed at the bottom of the infiltration pond is a promising technology to improve the quality of both recharged water and groundwater. As the reactive layer is made up of organic matter, all the redox processes are enhanced, improving the degradation of emerging pollutants. The success of coupling the MAR-SAR is based on the assumption that recharged water and groundwater are well mixed. Nevertheless, it is well known that mixing is not an instantaneous process in porous media. One strategy to improve it is the enhancement of chaotic advection through extraction-injection engineering (EIE). The EIE enhances mixing and, thus, all the reactions of the system. Although the emerging pollutant degradation is not well understood, it is known that some compounds are preferably degraded either in oxic or in reduced conditions. For example, in the case of benzotriazoles different redox conditions are required depending on each compound. Promoting different redox conditions in a system will result in an enhancement in the actual degree of degradation expected for any given compound. Considering all of this, our work is aimed to evaluate how caothic advection can improve mixing during MAR-SAR, and thus, be capable of enhancing the spreading of redox conditions with the final aim of improving benzotriazoles degradation. To achieve this, we have developed a reactive transport model that describes how recharged water (rich in organic matter coming from a reactive layer) is mixed with groundwater, and how this organic matter is oxidized by different electron acceptors. We have included the degradation rates of each benzotriazole compound in function of its reactivity with redox condition. The model has been tested in different scenarios of recharge and injection-extraction sequences, both in homogenous and in heterogeneous media. The preliminary results show that EIE improves the mixing between the recharged water and groundwater and increases the spreading of the plume. Consequently, the redox zonation is found to be spread spatially, with the coexistence of different redox conditions and, consequently, enhancing benzotriazoles degradation.

Setting healthcare priorities: a description and evaluation of the budgeting and planning process in county hospitals in Kenya

PubMed Central

Cleary, Susan; Molyneux, Sassy; English, Mike

2017-01-01

Abstract This paper describes and evaluates the budgeting and planning processes in public hospitals in Kenya. We used a qualitative case study approach to examine these processes in two hospitals in Kenya. We collected data by in-depth interviews of national level policy makers, hospital managers, and frontline practitioners in the case study hospitals (n = 72), a review of documents, and non-participant observations within the hospitals over a 7 month period. We applied an evaluative framework that considers both consequentialist and proceduralist conditions as important to the quality of priority-setting processes. The budgeting and planning process in the case study hospitals was characterized by lack of alignment, inadequate role clarity and the use of informal priority-setting criteria. With regard to consequentialist conditions, the hospitals incorporated economic criteria by considering the affordability of alternatives, but rarely considered the equity of allocative decisions. In the first hospital, stakeholders were aware of - and somewhat satisfied with - the budgeting and planning process, while in the second hospital they were not. Decision making in both hospitals did not result in reallocation of resources. With regard to proceduralist conditions, the budgeting and planning process in the first hospital was more inclusive and transparent, with the stakeholders more empowered compared to the second hospital. In both hospitals, decisions were not based on evidence, implementation of decisions was poor and the community was not included. There were no mechanisms for appeals or to ensure that the proceduralist conditions were met in both hospitals. Public hospitals in Kenya could improve their budgeting and planning processes by harmonizing these processes, improving role clarity, using explicit priority-setting criteria, and by incorporating both consequentialist (efficiency, equity, stakeholder satisfaction and understanding, shifted priorities, implementation of decisions), and proceduralist (stakeholder engagement and empowerment, transparency, use of evidence, revisions, enforcement, and incorporating community values) conditions. PMID:27679522

Setting healthcare priorities: a description and evaluation of the budgeting and planning process in county hospitals in Kenya.

PubMed

Barasa, Edwine W; Cleary, Susan; Molyneux, Sassy; English, Mike

2017-04-01

This paper describes and evaluates the budgeting and planning processes in public hospitals in Kenya. We used a qualitative case study approach to examine these processes in two hospitals in Kenya. We collected data by in-depth interviews of national level policy makers, hospital managers, and frontline practitioners in the case study hospitals (n = 72), a review of documents, and non-participant observations within the hospitals over a 7 month period. We applied an evaluative framework that considers both consequentialist and proceduralist conditions as important to the quality of priority-setting processes. The budgeting and planning process in the case study hospitals was characterized by lack of alignment, inadequate role clarity and the use of informal priority-setting criteria. With regard to consequentialist conditions, the hospitals incorporated economic criteria by considering the affordability of alternatives, but rarely considered the equity of allocative decisions. In the first hospital, stakeholders were aware of - and somewhat satisfied with - the budgeting and planning process, while in the second hospital they were not. Decision making in both hospitals did not result in reallocation of resources. With regard to proceduralist conditions, the budgeting and planning process in the first hospital was more inclusive and transparent, with the stakeholders more empowered compared to the second hospital. In both hospitals, decisions were not based on evidence, implementation of decisions was poor and the community was not included. There were no mechanisms for appeals or to ensure that the proceduralist conditions were met in both hospitals. Public hospitals in Kenya could improve their budgeting and planning processes by harmonizing these processes, improving role clarity, using explicit priority-setting criteria, and by incorporating both consequentialist (efficiency, equity, stakeholder satisfaction and understanding, shifted priorities, implementation of decisions), and proceduralist (stakeholder engagement and empowerment, transparency, use of evidence, revisions, enforcement, and incorporating community values) conditions. © The Author 2016. Published by Oxford University Press in association with The London School of Hygiene and Tropical Medicine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ankireddy, Krishnamraju; Ghahremani, Amir H.; Martin, Blake

Perovskite thin films are thermally annealed using a rapid intense pulsed light technique enabled by an alkyl halide that collectively improves device performance when processed in ambient conditions.

Surfactant-Assisted Coal Liquefaction

NASA Technical Reports Server (NTRS)

Hickey, Gregory S.; Sharma, Pramod K.

1993-01-01

Obtaining liquid fuels from coal which are economically competitive with those obtained from petroleum based sources is a significant challenge for the researcher as well as the chemical industry. Presently, the economics of coal liquefaction are not favorable because of relatively intense processing conditions (temperatures of 430 degrees C and pressures of 2200 psig), use of a costly catalyst, and a low quality product slate of relatively high boiling fractions. The economics could be made more favorable by achieving adequate coal conversions at less intense processing conditions and improving the product slate. A study has been carried out to examine the effect of a surfactant in reducing particle agglomeration and improving hydrodynamics in the coal liquefaction reactor to increase coal conversions...

Characterization of stainless steel surface processed using electrolytic oxidation and titanium complex ion solution

NASA Astrophysics Data System (ADS)

Kang, Yubin; Choi, Jaeyoung; Park, Jinju; Kim, Woo-Byoung; Lee, Kun-Jae

2017-09-01

This study attempts to improve the physical and chemical adhesion between metals and ceramics by using electrolytic oxidation and a titanium organic/inorganic complex ion solution on the SS-304 plate. Surface analysis confirmed the existence of the Tisbnd Osbnd Mx bonds formed by the bonding between the metal ions and the Ti oxide at the surface of the pre-processed SS plate, and improved chemical adhesion during ceramic coating was expected by confirming the presence of the carboxylic group. The adhesion was evaluated by using the ceramic coating solution in order to assess the improved adhesion of the SS plate under conditions. The results showed that both the adhesion and durability were largely improved in the sample processed with all the pre-processing steps, thus confirming that the physical and chemical adhesion between metals and ceramics can be improved by enhancing the physical roughness via electrolytic oxidation and pre-processing using a Ti complex ion solution.

The utilization of six sigma and statistical process control techniques in surgical quality improvement.

PubMed

Sedlack, Jeffrey D

2010-01-01

Surgeons have been slow to incorporate industrial reliability techniques. Process control methods were applied to surgeon waiting time between cases, and to length of stay (LOS) after colon surgery. Waiting times between surgeries were evaluated by auditing the operating room records of a single hospital over a 1-month period. The medical records of 628 patients undergoing colon surgery over a 5-year period were reviewed. The average surgeon wait time between cases was 53 min, and the busiest surgeon spent 291/2 hr in 1 month waiting between surgeries. Process control charting demonstrated poor overall control of the room turnover process. Average LOS after colon resection also demonstrated very poor control. Mean LOS was 10 days. Weibull's conditional analysis revealed a conditional LOS of 9.83 days. Serious process management problems were identified in both analyses. These process issues are both expensive and adversely affect the quality of service offered by the institution. Process control mechanisms were suggested or implemented to improve these surgical processes. Industrial reliability and quality management tools can easily and effectively identify process control problems that occur on surgical services. © 2010 National Association for Healthcare Quality.

Process for preparing transition metal nitrides and transition metal carbonitrides and their reaction intermediates

DOEpatents

Maya, Leon

1988-05-24

A process for making ammonolytic precursors to nitride and carbonitride ceramics. Extreme reaction conditions are not required and the precursor is a powder-like substance that produces ceramics of improved purity and morphology upon pyrolysis.

32 CFR 203.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... for making environmental decisions for their component or the director of the Defense Agencies. DoD...-making process by improving the public's understanding of overall conditions and activities. Technical... communications with the Department of Defense regarding the TAPP procurement process. The community point of...

Science-policy processes for transboundary water governance.

PubMed

Armitage, Derek; de Loë, Rob C; Morris, Michelle; Edwards, Tom W D; Gerlak, Andrea K; Hall, Roland I; Huitema, Dave; Ison, Ray; Livingstone, David; MacDonald, Glen; Mirumachi, Naho; Plummer, Ryan; Wolfe, Brent B

2015-09-01

In this policy perspective, we outline several conditions to support effective science-policy interaction, with a particular emphasis on improving water governance in transboundary basins. Key conditions include (1) recognizing that science is a crucial but bounded input into water resource decision-making processes; (2) establishing conditions for collaboration and shared commitment among actors; (3) understanding that social or group-learning processes linked to science-policy interaction are enhanced through greater collaboration; (4) accepting that the collaborative production of knowledge about hydrological issues and associated socioeconomic change and institutional responses is essential to build legitimate decision-making processes; and (5) engaging boundary organizations and informal networks of scientists, policy makers, and civil society. We elaborate on these conditions with a diverse set of international examples drawn from a synthesis of our collective experiences in assessing the opportunities and constraints (including the role of power relations) related to governance for water in transboundary settings.

ARM - Midlatitude Continental Convective Clouds

DOE Data Explorer

Jensen, Mike; Bartholomew, Mary Jane; Genio, Anthony Del; Giangrande, Scott; Kollias, Pavlos

2012-01-19

Convective processes play a critical role in the Earth's energy balance through the redistribution of heat and moisture in the atmosphere and their link to the hydrological cycle. Accurate representation of convective processes in numerical models is vital towards improving current and future simulations of Earths climate system. Despite improvements in computing power, current operational weather and global climate models are unable to resolve the natural temporal and spatial scales important to convective processes and therefore must turn to parameterization schemes to represent these processes. In turn, parameterization schemes in cloud-resolving models need to be evaluated for their generality and application to a variety of atmospheric conditions. Data from field campaigns with appropriate forcing descriptors have been traditionally used by modelers for evaluating and improving parameterization schemes.

ARM - Midlatitude Continental Convective Clouds (comstock-hvps)

DOE Data Explorer

Jensen, Mike; Comstock, Jennifer; Genio, Anthony Del; Giangrande, Scott; Kollias, Pavlos

2012-01-06

Convective processes play a critical role in the Earth's energy balance through the redistribution of heat and moisture in the atmosphere and their link to the hydrological cycle. Accurate representation of convective processes in numerical models is vital towards improving current and future simulations of Earths climate system. Despite improvements in computing power, current operational weather and global climate models are unable to resolve the natural temporal and spatial scales important to convective processes and therefore must turn to parameterization schemes to represent these processes. In turn, parameterization schemes in cloud-resolving models need to be evaluated for their generality and application to a variety of atmospheric conditions. Data from field campaigns with appropriate forcing descriptors have been traditionally used by modelers for evaluating and improving parameterization schemes.

{bold {ital In situ}} measurements of texture and phase development in (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10}{endash}Ag tapes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thurston, T.R.; Haldar, P.; Wang, Y.L.

Hard x-rays from a synchrotron source were utilized in diffraction experiments performed at elevated temperatures (up to {approximately}870{degree}C) on (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10} (Bi-2223) tapes {ital completely} encased in silver. The general behavior of the phase and texture development under typical processing conditions was determined, and the effects that several variations in processing conditions had on the phase and texture development were examined. These results and their implications for improving processing conditions are discussed. {copyright} {ital 1997 Materials Research Society.}

HIV-AIDS: urologic considerations.

PubMed

Lebovitch, Steve; Mydlo, Jack H

2008-02-01

The prevalence of HIV continues to grow in the United States and worldwide. HIV-positive patients experience many genitourinary disease processes. With improvements in HIV therapy, patients have questions and concerns pertaining to their quality of life. This article reviews conditions such as HIV-related urinary tract infections, urolithiasis, voiding dysfunction, fertility, sexual dysfunction, HIV-related nephropathy, malignancies, and occupational exposure and prophylaxis. Knowledge of the various HIV manifestations of genitourinary conditions and their treatment options benefits clinicians and improves patient outcomes.

Effects of planning strategies on writing dynamics and final texts.

PubMed

Limpo, Teresa; Alves, Rui A

2018-06-12

Expert writing involves the interaction among three cognitively demanding processes: planning, translating, and revising. To manage the cognitive load brought on by these processes, writers frequently use strategies. Here, we examined the effects of planning strategies on writing dynamics and final texts. Before writing an argumentative text with the triple-task technique, 63 undergraduates were asked either to elaborate an outline with the argumentative structure embedded (structure-based planning condition), to provide a written list of ideas for the text (list-based planning condition), or to do a non-writing-related filler task (no planning condition). Planning showed no effects on the length of the pre-writing pause and cognitive effort, but influenced writing processes occurrences. Compared to participants in the no-planning condition, those in the planning conditions showed a later activation of revising. Moreover, participants in the structure-based condition were mainly focused on translating in the beginning and middle of composition, whereas their peers tended to distribute their attention among all processes. Planning ahead of writing also resulted in texts with longer words, produced at a higher rate. Only the structure-based planning strategy led to an increase in the number of argumentation elements as well as in essays' persuasiveness and overall quality. There was, however, no indication that these improvements in final texts were associated with changes in the dynamics of writing. Overall, the use of structure-based plans seems to be an effective and efficient way of improving undergraduates' argumentative writing. Copyright © 2018 Elsevier B.V. All rights reserved.

Burnishing of rotatory parts to improve surface quality

NASA Astrophysics Data System (ADS)

Celaya, A.; López de Lacalle, L. N.; Albizuri, J.; Alberdi, R.

2009-11-01

In this paper, the use of rolling burnishing process to improve the final quality of railway and automotive workpieces is studied. The results are focused on the improvement of the manufacturing processes of rotary workpieces used in railway and automotion industry, attending to generic target of achieving `maximum surface quality with minimal process time'. Burnishing is a finishing operation in which plastic deformation of surface irregularities occurs by applying pressure through a very hard element, a roller or a ceramic ball. This process gives additional advantages to the workpiece such as good surface roughness, increased hardness and high compressive residual stresses. The effect of the initial turning conditions on the final burnishing operation has also been studied. The results show that feeds used in the initial rough turning have little influence in the surface finish of the burnished workpieces. So, the process times of the combined turning and burnishing processes can be reduced, optimizing the shaft's machining process.

Processing, quality and safety of irradiation - and high pressure processed meat and seafood products

USDA-ARS?s Scientific Manuscript database

In the past two decades, worldwide demands for meat and seafood products have increased dramatically due to the improved economical condition in many countries. To meet the demand, the producers have increased the production of meat and seafood products as well as applied new processing techniques t...

Augmenting CPT to Improve Sleep Impairment in PTSD: A Randomized Clinical Trial

PubMed Central

Galovski, Tara E.; Mott, Juliette; Blain, Leah M.; Elwood, Lisa; Gloth, Chelsea; Fletcher, Thomas

2015-01-01

Objective Despite the success of empirically supported treatments for posttraumatic stress disorder (PTSD), sleep impairment frequently remains refractory following treatment for PTSD. This single-site, randomized controlled trial examined the effectiveness of sleep-directed hypnosis as a complement to an empirically supported psychotherapy for PTSD (cognitive processing therapy; CPT). Method Participants completed either 3 weeks of hypnosis (n = 52) or a symptom monitoring control condition (n = 56) before beginning standard CPT. Multilevel modeling was used to investigate differential patterns of change to determine whether hypnosis resulted in improvements in sleep, PTSD, and depression. An intervening variable approach was then used to determine whether improvements in sleep achieved during hypnosis augmented change in PTSD and depression during CPT. Results After the initial phase of treatment (hypnosis or symptom monitoring), the hypnosis condition showed significantly greater improvement than the control condition in sleep and depression, but not PTSD. After CPT, both conditions demonstrated significant improvement in sleep and PTSD; however, the hypnosis condition demonstrated greater improvement in depressive symptoms. As sleep improved, there were corresponding improvements in PTSD and depression, with a stronger relationship between sleep and PTSD. Conclusion Hypnosis was effective in improving sleep impairment, but those improvements did not augment gains in PTSD recovery during the trauma-focused intervention. Public Health Significance: This study suggests that hypnosis may be a viable treatment option in a stepped-care approach for treating sleep impairment in individuals suffering from PTSD. PMID:26689303

Some functional limit theorems for compound Cox processes

NASA Astrophysics Data System (ADS)

Korolev, Victor Yu.; Chertok, A. V.; Korchagin, A. Yu.; Kossova, E. V.; Zeifman, Alexander I.

2016-06-01

An improved version of the functional limit theorem is proved establishing weak convergence of random walks generated by compound doubly stochastic Poisson processes (compound Cox processes) to Lévy processes in the Skorokhod space under more realistic moment conditions. As corollaries, theorems are proved on convergence of random walks with jumps having finite variances to Lévy processes with variance-mean mixed normal distributions, in particular, to stable Lévy processes.

Some functional limit theorems for compound Cox processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korolev, Victor Yu.; Institute of Informatics Problems FRC CSC RAS; Chertok, A. V.

2016-06-08

An improved version of the functional limit theorem is proved establishing weak convergence of random walks generated by compound doubly stochastic Poisson processes (compound Cox processes) to Lévy processes in the Skorokhod space under more realistic moment conditions. As corollaries, theorems are proved on convergence of random walks with jumps having finite variances to Lévy processes with variance-mean mixed normal distributions, in particular, to stable Lévy processes.

Hot Isostatic Press Manufacturing Process Development for Fabrication of RERTR Monolithic Fuel Plates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crapps, Justin M.; Clarke, Kester D.; Katz, Joel D.

2012-06-06

We use experimentation and finite element modeling to study a Hot Isostatic Press (HIP) manufacturing process for U-10Mo Monolithic Fuel Plates. Finite element simulations are used to identify the material properties affecting the process and improve the process geometry. Accounting for the high temperature material properties and plasticity is important to obtain qualitative agreement between model and experimental results. The model allows us to improve the process geometry and provide guidance on selection of material and finish conditions for the process strongbacks. We conclude that the HIP can must be fully filled to provide uniform normal stress across the bondingmore » interface.« less

A Chronic Disease Prevention and Management Corridor© to Supporting System-Level Transformations for Chronic Conditions.

PubMed

Sampalli, Tara; Christian, Erin; Edwards, Lynn; Ryer, Ashley

2015-01-01

Improving care for chronic conditions requires system-level transformations to ensure multiple levels of adoption and sustainability of the implemented improvements. These comprehensive solutions require transformations and supports at various levels, leadership and process changes at service/program level. Recognizing the importance of an organization-wide strategy to mitigate the growing issue of chronic disease prevention and management, a novel system-level approach has been developed in a district health authority in Nova Scotia, Canada. In this paper, the contextual factors and efforts that led to the conceptual framework of the Chronic Disease Prevention and Management (CDPM) "Corridor©" to management of chronic conditions are discussed. The CDPM Corridor© essentially constitutes a system-level redesign process; common elements, tools and resources; and a hub of supports for chronic disease prevention and management. The CDPM Corridor © will include a toolkit to guide the implementation of the proposed transformations.

Inert gas narcosis and the encoding and retrieval of long-term memory.

PubMed

Kneller, Wendy; Hobbs, Malcolm

2013-12-01

Prior research has indicated that inert gas narcosis (IGN) causes decrements in free recall memory performance and that these result from disruption of either encoding or self-guided search in the retrieval process. In a recent study we provided evidence, using a Levels of Processing approach, for the hypothesis that IGN affects the encoding of new information. The current study sought to replicate these results with an improved methodology. The effect of ambient pressure (111.5-212.8 kPa/1-11 msw vs. 456-516.8 kPa/35-41 msw) and level of processing (shallow vs. deep) on free recall memory performance was measured in 34 divers in the context of an underwater field experiment. Free recall was significantly worse at high ambient pressure compared to low ambient pressure in the deep processing condition (low pressure: M = 5.6; SD = 2.7; high pressure: M = 3.3; SD = 1.4), but not in the shallow processing condition (low pressure: M = 3.9; SD = 1.7; high pressure: M = 3.1; SD = 1.8), indicating IGN impaired memory ability in the deep processing condition. In the shallow water, deep processing improved recall over shallow processing but, significantly, this effect was eliminated in the deep water. In contrast to our earlier study this supported the hypothesis that IGN affects the self-guided search of information and not encoding. It is suggested that IGN may affect both encoding and self-guided search and further research is recommended.

Why do organizations not learn from incidents? Bottlenecks, causes and conditions for a failure to effectively learn.

PubMed

Drupsteen, Linda; Hasle, Peter

2014-11-01

If organizations would be able to learn more effectively from incidents that occurred in the past, future incidents and consequential injury or damage can be prevented. To improve learning from incidents, this study aimed to identify limiting factors, i.e. the causes of the failure to effectively learn. In seven organizations focus groups were held to discuss factors that according to employees contributed to the failure to learn. By use of a model of the learning from incidents process, the steps, where difficulties for learning arose, became visible, and the causes for these difficulties could be studied. Difficulties were identified in multiple steps of the learning process, but most difficulties became visible when planning actions, which is the phase that bridges the gap from incident investigation to actions for improvement. The main causes for learning difficulties, which were identified by the participants in this study, were tightly related to the learning process, but some indirect causes - or conditions - such as lack of ownership and limitations in expertise were also mentioned. The results illustrate that there are two types of causes for the failure to effectively learn: direct causes and indirect causes, here called conditions. By actively and systematically studying learning, more conditions might be identified and indicators for a successful learning process may be determined. Studying the learning process does, however, require a shift from learning from incidents to learning to learn. Copyright © 2014 Elsevier Ltd. All rights reserved.

Attentional focus and performance anxiety: effects on simulated race-driving performance and heart rate variability.

PubMed

Mullen, Richard; Faull, Andrea; Jones, Eleri S; Kingston, Kieran

2012-01-01

Previous studies have demonstrated that an external focus can enhance motor learning compared to an internal focus. The benefits of adopting an external focus are attributed to the use of less effortful automatic control processes, while an internal focus relies upon more effort-intensive consciously controlled processes. The aim of this study was to compare the effectiveness of a distal external focus with an internal focus in the acquisition of a simulated driving task and subsequent performance in a competitive condition designed to increase state anxiety. To provide further evidence for the automatic nature of externally controlled movements, the study included heart rate variability (HRV) as an index of mental effort. Sixteen participants completed eight blocks of four laps in either a distal external or internal focus condition, followed by two blocks of four laps in the competitive condition. During acquisition, the performance of both groups improved; however, the distal external focus group outperformed the internal focus group. The poorer performance of the internal focus group was accompanied by a larger reduction in HRV, indicating a greater investment of mental effort. In the competition condition, state anxiety increased, and for both groups, performance improved as a function of the increased anxiety. Increased heart rate and self-reported mental effort accompanied the performance improvement. The distal external focus group also outperformed the internal focus group across both neutral and competitive conditions and this more effective performance was again associated with lower levels of HRV. Overall, the results offer support for the suggestion that an external focus promotes a more automatic mode of functioning. In the competitive condition, both foci enhanced performance and while the improved performance may have been achieved at the expense of greater compensatory mental effort, this was not reflected in HRV scores.

Ethylene-propylene-diene monomer (EPDM) and fluorocarbon (FKM) elastomers in the geothermal environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harwood, H.J.

1983-07-01

Thermal and hydrolytic processes that are likely to occur when hydrocarbon and fluorocarbon elastomers are subjected to geothermal conditions are discussed. Polyhydrocarbon backbones have good chemical resistance, but many cross-links present in cured polyhydrocarbons can be hydrolyzed under geothermal conditions. Perfluorinated elastomers have excellent thermal and hydrolytic stability, although they are potentially susceptible to hydrolytic degradation. The cross-links present in cured perfluorocarbon elastomers are probably also susceptible to hydrolysis under severe conditions. It seems that improvements can be made in geothermal seals if they can be cured by processes that yield chemically stable cross-links.

Superacid Catalyzed Coal Conversion Chemistry. Final Technical Report, September 1, 1983-September 1, 1986

DOE R&D Accomplishments Database

Olah, G. A.

1986-01-01

This research project involved the study of a raw comparatively mild coal conversion process. The goal of the project was to study model systems to understand the basic chemistry involved and to provide a possible effective pretreatment of coal which significantly improves liquefaction-depolymerization under mild conditions. The conversion process operates at relatively low temperatures (170 degrees C) and pressures and uses an easily recyclable, stable superacid catalysts (HF-BF{sub 3}). It consequently offers an attractive alternative to currently available processes. From the present studies it appears that the modification of coal structure by electrophilic alkylation and subsequent reaction of alkylated coal with HF-BF{sub 3}-H{sub 2} system under mild conditions considerably improves the extractability of coal in pyridine and cyclohexane. On the other hand, nitration of coal and its subsequent reaction with HF-BF{sub 3}H{sub 2} decreases the pyridine and cyclohexane extractability. Study of model compounds under conditions identical with the superacidic HF/BF{sub 3}/H{sub 2} system provided significant information about the basic chemistry of the involved cleavage-hydrogenation reactions.

Improving safety on rural local and tribal roads site safety analysis - user guide #1.

DOT National Transportation Integrated Search

2014-08-01

This User Guide presents an example of how rural local and Tribal practitioners can study conditions at a preselected site. It demonstrates the step-by-step safety analysis process presented in Improving Safety on Rural Local and Tribal Roads Saf...

Generated spiral bevel gears: Optimal machine-tool settings and tooth contact analysis

NASA Technical Reports Server (NTRS)

Litvin, F. L.; Tsung, W. J.; Coy, J. J.; Heine, C.

1985-01-01

Geometry and kinematic errors were studied for Gleason generated spiral bevel gears. A new method was devised for choosing optimal machine settings. These settings provide zero kinematic errors and an improved bearing contact. The kinematic errors are a major source of noise and vibration in spiral bevel gears. The improved bearing contact gives improved conditions for lubrication. A computer program for tooth contact analysis was developed, and thereby the new generation process was confirmed. The new process is governed by the requirement that during the generation process there is directional constancy of the common normal of the contacting surfaces for generator and generated surfaces of pinion and gear.

An exploratory study of the relationship between changes in emotion and cognitive processes and treatment outcome in borderline personality disorder.

PubMed

McMain, Shelley; Links, Paul S; Guimond, Tim; Wnuk, Susan; Eynan, Rahel; Bergmans, Yvonne; Warwar, Serine

2013-01-01

This exploratory study examined specific emotion processes and cognitive problem-solving processes in individuals with borderline personality disorder (BPD), and assessed the relationship of these changes to treatment outcome. Emotion and cognitive problem-solving processes were assessed using the Toronto Alexithymia Scale, the Linguistic Inquiry Word Count, the Derogatis Affect Balance Scale, and the Problem Solving Inventory. Participants who showed greater improvements in affect balance, problem solving, and the ability to identify and describe emotions showed greater improvements on treatment outcome, with affect balance remaining statistically significant under the most conservative conditions. The results provide preliminary evidence to support the theory that specific improvements in emotion and cognitive processes are associated with positive treatment outcomes (symptom distress, interpersonal functioning) in BPD. The implications for treatment are discussed.

Influence of organic matter on arsenic removal by continuous flow electrocoagulation treatment of weakly mineralized waters.

PubMed

Pallier, Virginie; Feuillade-Cathalifaud, Geneviève; Serpaud, Bernard

2011-03-01

The aim of this study is to evaluate and understand the electrocoagulation/flocculation (ECF) process to remove arsenic from both model and natural waters with low mineral content and to compare its performances to the coagulation/flocculation (CF) process already optimized. Experiments were thus conducted with iron electrodes in the same specific treatment conditions (4≤current density (mAcm(-2))≤33) to study the influence of organic matter on arsenic removal in conditions avoiding the oxidation step usually required to improve As(III) removal. The process performance was evaluated by combining quantification of arsenic residual concentrations and speciation and dissolved organic carbon residual concentrations with zeta potential and turbidity measurements. When compared to CF, ECF presented several disadvantages: (i) lower As(V) removal yield because of the ferrous iron dissolved from the anode and the subsequent negative zeta potential of the colloidal suspension, (ii) higher residual DOC concentrations because of the fractionation of high molecular weight compounds during the treatment leading to compounds less prone to coagulate and (iii) higher residual turbidities because of the charge neutralization mechanisms involved. However, during this process, As(III) was oxidized to As(V) improving considerably its removal whatever the matrix conditions. ECF thus allowed to improve As(III) removal without applying an oxidation step that could potentially lead to the formation of toxic oxidation by-products. Copyright © 2011 Elsevier Ltd. All rights reserved.

Temporal information processing in short- and long-term memory of patients with schizophrenia.

PubMed

Landgraf, Steffen; Steingen, Joerg; Eppert, Yvonne; Niedermeyer, Ulrich; van der Meer, Elke; Krueger, Frank

2011-01-01

Cognitive deficits of patients with schizophrenia have been largely recognized as core symptoms of the disorder. One neglected factor that contributes to these deficits is the comprehension of time. In the present study, we assessed temporal information processing and manipulation from short- and long-term memory in 34 patients with chronic schizophrenia and 34 matched healthy controls. On the short-term memory temporal-order reconstruction task, an incidental or intentional learning strategy was deployed. Patients showed worse overall performance than healthy controls. The intentional learning strategy led to dissociable performance improvement in both groups. Whereas healthy controls improved on a performance measure (serial organization), patients improved on an error measure (inappropriate semantic clustering) when using the intentional instead of the incidental learning strategy. On the long-term memory script-generation task, routine and non-routine events of everyday activities (e.g., buying groceries) had to be generated in either chronological or inverted temporal order. Patients were slower than controls at generating events in the chronological routine condition only. They also committed more sequencing and boundary errors in the inverted conditions. The number of irrelevant events was higher in patients in the chronological, non-routine condition. These results suggest that patients with schizophrenia imprecisely access temporal information from short- and long-term memory. In short-term memory, processing of temporal information led to a reduction in errors rather than, as was the case in healthy controls, to an improvement in temporal-order recall. When accessing temporal information from long-term memory, patients were slower and committed more sequencing, boundary, and intrusion errors. Together, these results suggest that time information can be accessed and processed only imprecisely by patients who provide evidence for impaired time comprehension. This could contribute to symptomatic cognitive deficits and strategic inefficiency in schizophrenia.

Method and means for producing fluorocarbon finishes on fibrous structures

NASA Technical Reports Server (NTRS)

Toy, Madeline S. (Inventor); Stringham, Roger S. (Inventor); Fogg, Lawrence C. (Inventor)

1981-01-01

An improved process and apparatus is provided for imparting chemically bonded fluorocarbon finishes to textiles. In the process, the textiles are contacted with a gaseous mixture of fluoroolefins in an inert diluent gas in the presence of ultraviolet light under predetermined conditions.

14 CFR 1260.57 - New technology.

Code of Federal Regulations, 2013 CFR

2013-01-01

... operate, in case of a machine or system; and, in each case, under such conditions as to establish that the... items include, but are not limited to, new processes, machines, manufactures, and compositions of matter, and improvements to, or new applications of, existing processes, machines, manufactures, and...

14 CFR 1260.57 - New technology.

Code of Federal Regulations, 2012 CFR

2012-01-01

... operate, in case of a machine or system; and, in each case, under such conditions as to establish that the... items include, but are not limited to, new processes, machines, manufactures, and compositions of matter, and improvements to, or new applications of, existing processes, machines, manufactures, and...

Trends in non-stationary signal processing techniques applied to vibration analysis of wind turbine drive train - A contemporary survey

NASA Astrophysics Data System (ADS)

Uma Maheswari, R.; Umamaheswari, R.

2017-02-01

Condition Monitoring System (CMS) substantiates potential economic benefits and enables prognostic maintenance in wind turbine-generator failure prevention. Vibration Monitoring and Analysis is a powerful tool in drive train CMS, which enables the early detection of impending failure/damage. In variable speed drives such as wind turbine-generator drive trains, the vibration signal acquired is of non-stationary and non-linear. The traditional stationary signal processing techniques are inefficient to diagnose the machine faults in time varying conditions. The current research trend in CMS for drive-train focuses on developing/improving non-linear, non-stationary feature extraction and fault classification algorithms to improve fault detection/prediction sensitivity and selectivity and thereby reducing the misdetection and false alarm rates. In literature, review of stationary signal processing algorithms employed in vibration analysis is done at great extent. In this paper, an attempt is made to review the recent research advances in non-linear non-stationary signal processing algorithms particularly suited for variable speed wind turbines.

Properties of autoclaved Gr/PI composites made from improved tack PMR-15 prepreg

NASA Technical Reports Server (NTRS)

Vannucci, R. D.

1985-01-01

Autoclave processing studies were conducted, using improved tack PMR-15 prepreg, to determine the effect of tack enhancing PMR resin modifications on composite processability and mechanical properties. Improved tack graphite fiber reinforced PMR-15 prepregs were prepared and exposed to ambient conditions for various times and then autoclave molded into composites. Composite specimens were prepared and tested for flexural and interlaminar shear strengths at room temperature and 316 C. The retention of flexural and interlaminar shear strength as a function of exposure in air at 316 C was also determined. The results show that the modified PMR resin solutions provide prepreg with improved tack and drape retention characteristics without adversely affecting processability or mechanical properties of autoclave molded graphite fiber reinforced PMR-15 composites.

[Microhemocirculation and its correction in duodenal ulcer during period of rehabilitation].

PubMed

Parpibaeva, D A; Zakirkhodzhaev, Sh Ia; Sagatov, T A; Shakirova, D T; Narziev, N M

2009-01-01

The background of this research is to study morphological and functional microcirculatory channel condition with duodenum ulcer in the period of rehabilitation against the background of regular antiulcer therapy (1 group) and further treatment using Vazonit (2 group) in clinical conditions. EDU in animals results in marked microcirculatory disease in duodenum depending on the time of ulcer process development. Hypoxia is to be the significant factor associated with capillary stases, venous congestion. Blood flow impairment in organ results in metabolic damages of tissue structures. The results obtained are evidence of significant correction of microcirculatory channel state, improvement of regeneration and reparation processes. Vazonit improves the disorder of microcirculation and theological blood properties, restoring of macro and microangiopathy changes of hemocirculatory channel.

Effects of Coating Materials and Processing Conditions on Flow Enhancement of Cohesive Acetaminophen Powders by High-Shear Processing With Pharmaceutical Lubricants.

PubMed

Wei, Guoguang; Mangal, Sharad; Denman, John; Gengenbach, Thomas; Lee Bonar, Kevin; Khan, Rubayat I; Qu, Li; Li, Tonglei; Zhou, Qi Tony

2017-10-01

This study has investigated the surface coating efficiency and powder flow improvement of a model cohesive acetaminophen powder by high-shear processing with pharmaceutical lubricants through 2 common equipment, conical comil and high-shear mixer. Effects of coating materials and processing parameters on powder flow and surface coating coverage were evaluated. Both Carr's index and shear cell data indicated that processing with the lubricants using comil or high-shear mixer substantially improved the flow of the cohesive acetaminophen powder. Flow improvement was most pronounced for those processed with 1% wt/wt magnesium stearate, from "cohesive" for the V-blended sample to "easy flowing" for the optimally coated sample. Qualitative and quantitative characterizations demonstrated a greater degree of surface coverage for high-shear mixing compared with comilling; nevertheless, flow properties of the samples at the corresponding optimized conditions were comparable between 2 techniques. Scanning electron microscopy images demonstrated different coating mechanisms with magnesium stearate or l-leucine (magnesium stearate forms a coating layer and leucine coating increases surface roughness). Furthermore, surface coating with hydrophobic magnesium stearate did not retard the dissolution kinetics of acetaminophen. Future studies are warranted to evaluate tableting behavior of such dry-coated pharmaceutical powders. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Learning to re-appraise the self during video feedback for social anxiety: Does depth of processing matter?

PubMed

Orr, Elizabeth M J; Moscovitch, David A

2010-08-01

Video feedback (VF) with cognitive preparation (CP) has been widely integrated into cognitive-behavioral therapy (CBT) protocols for social anxiety disorder (SAD) due to its presumed efficacy in improving negative self-perception. However, previous experimental studies have demonstrated that improvements in negative self-perception via VF+CP do not typically facilitate anxiety reduction during subsequent social interactions - a troubling finding for proponents of cognitive models of social anxiety. We examined whether VF+CP could be optimized to enhance participants' processing of corrective self-related information through the addition of a post-VF cognitive review (CR). Sixty-eight socially anxious individuals were randomly assigned to perform two public speeches in one of the following conditions: a) exposure alone (EXP); b) CP+VF; and c) CP+VF+CR. Those in the CP+VF+CR condition demonstrated marginally significant reductions in anxiety from speech 1 to speech 2 relative to those who received EXP - an improvement not shown for those in the CP+VF condition. Furthermore, only those who received CP+VF+CR demonstrated significant improvements in self-perception and performance expectations relative to EXP. Decreases in anxiety among participants who received CP+VF+CR relative to EXP were fully mediated by improvements in self-perception. Implications are discussed in the context of cognitive models of social anxiety and mechanisms of exposure-based learning. Copyright 2010 Elsevier Ltd. All rights reserved.

Influence of processing on the microstructure and mechanical properties of 14YWT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoelzer, D. T.; Unocic, K. A.; Sokolov, Mikhail A.

2016-04-25

The investigation of the mechanical alloying (MA) conditions for producing the advanced oxide dispersion strengthened (ODS) 14YWT ferritic alloy led to significant improvements in balancing the strength, ductility and fracture toughness properties while still maintaining the salient microstructural features consisting of ultra-fine grains and high concentration of Y-, Ti- and O-enriched nanoclusters. The implemented changes to the processing conditions included reducing the contamination of the powder during ball milling, applying a pre-extrusion annealing treatment on the ball milled powder and exploring different extrusion temperatures at 850 C (SM170 heat), 1000 C (SM185) and 1150 C (SM200). The microstructural studies ofmore » the three 14YWT heats showed similarities in the dispersion of nanoclusters and sub-micron size grains, indicating the microstructure was insensitive to the different extrusion conditions. Compared to past 14YWT heats, the three new heats showed lower strength, but higher ductility levels between 25 and 800 C and significantly higher fracture toughness values between 25 C and 700 C. The lower contamination levels of O, C and N achieved with improved ball milling conditions plus the slightly larger grain size were identified as important factors for improving the balance in mechanical properties of the three heats of 14YWT.« less

Process Setting through General Linear Model and Response Surface Method

NASA Astrophysics Data System (ADS)

Senjuntichai, Angsumalin

2010-10-01

The objective of this study is to improve the efficiency of the flow-wrap packaging process in soap industry through the reduction of defectives. At the 95% confidence level, with the regression analysis, the sealing temperature, temperatures of upper and lower crimper are found to be the significant factors for the flow-wrap process with respect to the number/percentage of defectives. Twenty seven experiments have been designed and performed according to three levels of each controllable factor. With the general linear model (GLM), the suggested values for the sealing temperature, temperatures of upper and lower crimpers are 185, 85 and 85° C, respectively while the response surface method (RSM) provides the optimal process conditions at 186, 89 and 88° C. Due to different assumptions between percentage of defective and all three temperature parameters, the suggested conditions from the two methods are then slightly different. Fortunately, the estimated percentage of defectives at 5.51% under GLM process condition and the predicted percentage of defectives at 4.62% under RSM process condition are not significant different. But at 95% confidence level, the percentage of defectives under RSM condition can be much lower approximately 2.16% than those under GLM condition in accordance with wider variation. Lastly, the percentages of defectives under the conditions suggested by GLM and RSM are reduced by 55.81% and 62.95%, respectively.

Spectroscopic studies of triethoxysilane sol-gel and coating process.

PubMed

Li, Ying-Sing; Ba, Abdul

2008-10-01

Silica sol-gels have been prepared under different conditions using triethoxysilane (TES) as precursor. The prepared sol-gels have been used to coat aluminum for corrosion protection. Vibrational assignments have been made for most vibration bands of TES, TES sol-gel, TES sol-gel-coated aluminum and xerogel. It has been noticed that air moisture may have helped the hydrolysis of the thin coating films. Xerogels have been obtained from the sol-gel under different temperature conditions and the resulting samples have been characterized by using infrared and Raman spectroscopic methods. IR data indicate that the sol-gel process is incomplete under the ambient conditions although an aqueous condition can have slightly improved the process. Two nonequivalent silicon atoms have been identified from the collected 29Si NMR spectra for the sol-gel, supporting the result derived from the IR data. The frequency of Si-H bending vibration has been found to be more sensitive to the skeletal structure than that of the Si-H stretching vibration. A higher temperature condition could favor the progression of hydrolysis and condensation. A temperature higher than 300 degrees C would cause sample decomposition without seriously damaging the silica network. From infrared intensity measurements and thermo-gravimetric analyses, the fractions of incomplete hydrolysis and condensation species have been estimated to be 4% and 3%, respectively. Electrochemical data have shown that the sol-gel coating significantly improves the corrosion protection properties of aluminum.

Ergonomics policy in Indonesia.

PubMed

Sutarjo, Untung S

2007-12-01

Workers' conditions in accordance with their place of work are different from one area to another, especially in this reformation era where there are immense alterations in politics shown from the centralized government shifting to decentralization and district autonomy. Ergonomics problems in Indonesia are reviewed. In home industries, workers have to adjust themselves to their jobs, and ergonomic improvement may face significant impediments especially in small-scale industries. It is necessary to create or identify the most plausible model to be implemented in accordance with the conditions of districts, including low awareness about the relation between ergonomics and workers' productivity in producing goods and services and working processes scattered often at their own houses. As conditions conducive to ergonomics programs, district-level willingness to improve and increase the wealth of their society, recognition by businesses about the impacts of ergonomics on productivity and reduction of medical treatment costs may be mentioned. Labor unions support ergonomic improvements at production processes, and professionals and academicians are ready to assist, whereas national banks and foreign investment may encourage new technologies including ergonomics aspects. It is important to strengthen ergonomic improvement efforts in Indonesia through establishing district ergonomics improvement networks and ergonomics peer leaders with the support of continual training starting from the training of core leaders at the province level and extending to peer leaders at district level. This training should be made as simple as possible in order to facilitate innovations toward changes. Finally assistance is needed by the mentor teams in order to periodically monitor the improvements undertaken.

Dying scenarios improve recall as much as survival scenarios.

PubMed

Burns, Daniel J; Hart, Joshua; Kramer, Melanie E

2014-01-01

Merely contemplating one's death improves retention for entirely unrelated material learned subsequently. This "dying to remember" effect seems conceptually related to the survival processing effect, whereby processing items for their relevance to being stranded in the grasslands leads to recall superior to that of other deep processing control conditions. The present experiments directly compared survival processing scenarios with "death processing" scenarios. Results showed that when the survival and dying scenarios are closely matched on key dimensions, and possible congruency effects are controlled, the dying and survival scenarios produced equivalently high recall levels. We conclude that the available evidence (cf. Bell, Roer, & Buchner, 2013; Klein, 2012), while not definitive, is consistent with the possibility of overlapping mechanisms.

Improving Logistics Processes in Industry Using Web Technologies

NASA Astrophysics Data System (ADS)

Jánošík, Ján; Tanuška, Pavol; Václavová, Andrea

2016-12-01

The aim of this paper is to propose the concept of a system that takes advantage of web technologies and integrates them into the management process and management of internal stocks which may relate to external applications and creates the conditions to transform a Computerized Control of Warehouse Stock (CCWS) in the company. The importance of implementing CCWS is in the elimination of the claims caused by the human factor, as well as to allow the processing of information for analytical purposes and their subsequent use to improve internal processes. Using CCWS in the company would also facilitate better use of the potential tools Business Intelligence and Data Mining.

Improvements in Low-cost Ultrasonic Measurements of Blood Flow in "by-passes" Using Narrow & Broad Band Transit-time Procedures

NASA Astrophysics Data System (ADS)

Ramos, A.; Calas, H.; Diez, L.; Moreno, E.; Prohías, J.; Villar, A.; Carrillo, E.; Jiménez, A.; Pereira, W. C. A.; Von Krüger, M. A.

The cardio-pathology by ischemia is an important cause of death, but the re-vascularization of coronary arteries (by-pass operation) is an useful solution to reduce associated morbidity improving quality of life in patients. During these surgeries, the flow in coronary vessels must be measured, using non-invasive ultrasonic methods, known as transit time flow measurements (TTFM), which are the most accurate option nowadays. TTFM is a common intra-operative tool, in conjunction with classic Doppler velocimetry, to check the quality of these surgery processes for implanting grafts in parallel with the coronary arteries. This work shows important improvements achieved in flow-metering, obtained in our research laboratories (CSIC, ICIMAF, COPPE) and tested under real surgical conditions in Cardiocentro-HHA, for both narrowband NB and broadband BB regimes, by applying results of a CYTED multinational project (Ultrasonic & computational systems for cardiovascular diagnostics). mathematical models and phantoms were created to evaluate accurately flow measurements, in laboratory conditions, before our new electronic designs and low-cost implementations, improving previous ttfm systems, which include analogic detection, acquisition & post-processing, and a portable PC. Both regimes (NB and BB), with complementary performances for different conditions, were considered. Finally, specific software was developed to offer facilities to surgeons in their interventions.

Application of agent-based system for bioprocess description and process improvement.

PubMed

Gao, Ying; Kipling, Katie; Glassey, Jarka; Willis, Mark; Montague, Gary; Zhou, Yuhong; Titchener-Hooker, Nigel J

2010-01-01

Modeling plays an important role in bioprocess development for design and scale-up. Predictive models can also be used in biopharmaceutical manufacturing to assist decision-making either to maintain process consistency or to identify optimal operating conditions. To predict the whole bioprocess performance, the strong interactions present in a processing sequence must be adequately modeled. Traditionally, bioprocess modeling considers process units separately, which makes it difficult to capture the interactions between units. In this work, a systematic framework is developed to analyze the bioprocesses based on a whole process understanding and considering the interactions between process operations. An agent-based approach is adopted to provide a flexible infrastructure for the necessary integration of process models. This enables the prediction of overall process behavior, which can then be applied during process development or once manufacturing has commenced, in both cases leading to the capacity for fast evaluation of process improvement options. The multi-agent system comprises a process knowledge base, process models, and a group of functional agents. In this system, agent components co-operate with each other in performing their tasks. These include the description of the whole process behavior, evaluating process operating conditions, monitoring of the operating processes, predicting critical process performance, and providing guidance to decision-making when coping with process deviations. During process development, the system can be used to evaluate the design space for process operation. During manufacture, the system can be applied to identify abnormal process operation events and then to provide suggestions as to how best to cope with the deviations. In all cases, the function of the system is to ensure an efficient manufacturing process. The implementation of the agent-based approach is illustrated via selected application scenarios, which demonstrate how such a framework may enable the better integration of process operations by providing a plant-wide process description to facilitate process improvement. Copyright 2009 American Institute of Chemical Engineers

48 CFR 1852.227-70 - New technology.

Code of Federal Regulations, 2011 CFR

2011-10-01

... method; or to operate, in case of a machine or system; and, in each case, under such conditions as to... contract. Reportable items include, but are not limited to, new processes, machines, manufactures, and compositions of matter, and improvements to, or new applications of, existing processes, machines, manufactures...

14 CFR § 1260.57 - New technology.

Code of Federal Regulations, 2014 CFR

2014-01-01

... operate, in case of a machine or system; and, in each case, under such conditions as to establish that the... items include, but are not limited to, new processes, machines, manufactures, and compositions of matter, and improvements to, or new applications of, existing processes, machines, manufactures, and...

The New Drug Conditional Approval Process in China: Challenges and Opportunities.

PubMed

Yao, Xuefang; Ding, Jinxi; Liu, Yingfang; Li, Penghui

2017-05-01

Our aim was to characterize the newly established new drug conditional approval process in China and discuss the challenges and opportunities with respect to new drug research and development and registration. We examined the new approval program through literature review, law analysis, and data analysis. Data were derived from published materials, such as journal articles, government publications, press releases, and news articles, along with statistical data from INSIGHT-China Pharma Databases, the China Food and Drug Administration website, the Center for Drug Evaluation website, the US Food and Drug Administration website, and search results published by Google. Currently, there is a large backlog of New Drug Applications in China, mainly because of the prolonged review time at the China Food and Drug Administration, resulting in a lag in drug approvals. In 2015, the Chinese government implemented the drug review and registration system reform and tackled this issue through various approaches, such as setting up a drug review fee system, adjusting the drug registration classification, and establishing innovative review pathways, including the conditional approval process. In Europe and the United States, programs comparable to the conditional approval program in China have been well developed. The conditional approval program recently established in China is an expedited new drug approval process that is expected to affect new drug development at home and abroad and profoundly influence the public health and the pharmaceutical industry in China. Like any program in its initial stage, the conditional approval program is facing several challenges, including setting up a robust system, formatting new drug clinical research requirements, and improving the regulatory agency's function for drug review and approval. The program is expected to evolve and improve as part of the government mandate of the drug registration system reform. Copyright © 2017 Elsevier HS Journals, Inc. All rights reserved.

Radiation-Thermal Sintering of Zirconia Powder Compacts Under Conditions of Bilateral Heating Using Beams of Low-Energy Electrons

NASA Astrophysics Data System (ADS)

Ghyngazov, S. A.; Frangulyan, T. S.; Chernyavskii, A. V.; Goreev, A. K.; Naiden, E. P.

2015-06-01

Comparative experiments on sintering zirconia ceramics are performed using colliding beams of low-energy electrons and under conditions of thermal heating. The density and microhardness of ceramic materials manufactured via different processes are determined. The use of a regime of bilateral heating by high-intensity,low-energy electron beams is shown to intensify the sintering process and yield material specimens with improved characteristics compared to those formed by thermal sintering.

Improvement of crystal identification performance for a four-layer DOI detector composed of crystals segmented by laser processing

NASA Astrophysics Data System (ADS)

Mohammadi, Akram; Inadama, Naoko; Yoshida, Eiji; Nishikido, Fumihiko; Shimizu, Keiji; Yamaya, Taiga

2017-09-01

We have developed a four-layer depth of interaction (DOI) detector with single-side photon readout, in which segmented crystals with the patterned reflector insertion are separately identified by the Anger-type calculation. Optical conditions between segmented crystals, where there is no reflector, affect crystal identification ability. Our objective of this work was to improve crystal identification performance of the four-layer DOI detector that uses crystals segmented with a recently developed laser processing technique to include laser processed boundaries (LPBs). The detector consisted of 2 × 2 × 4mm3 LYSO crystals and a 4 × 4 array multianode photomultiplier tube (PMT) with 4.5 mm anode pitch. The 2D position map of the detector was calculated by the Anger calculation method. At first, influence of optical condition on crystal identification was evaluated for a one-layer detector consisting of a 2 × 2 crystal array with three different optical conditions between the crystals: crystals stuck together using room temperature vulcanized (RTV) rubber, crystals with air coupling and segmented crystals with LPBs. The crystal array with LPBs gave the shortest distance between crystal responses in the 2D position map compared with the crystal array coupled with RTV rubber or air due to the great amount of cross-talk between segmented crystals with LPBs. These results were used to find optical conditions offering the optimum distance between crystal responses in the 2D position map for the four-layer DOI detector. Crystal identification performance for the four-layer DOI detector consisting of an 8 × 8 array of crystals segmented with LPBs was examined and it was not acceptable for the crystals in the first layer. The crystal identification was improved for the first layer by changing the optical conditions between all 2 × 2 crystal arrays of the first layer to RTV coupling. More improvement was observed by combining different optical conditions between all crystals of the first layer and some crystals of the second and the third layers of the segmented array.

Recent Improvements in Semi-Span Testing at the National Transonic Facility (Invited)

NASA Technical Reports Server (NTRS)

Gatlin, G. M.; Tomek, W. G.; Payne, F. M.; Griffiths, R. C.

2006-01-01

Three wind tunnel investigations of a commercial transport, high-lift, semi-span configuration have recently been conducted in the National Transonic Facility at the NASA Langley Research Center. Throughout the course of these investigations multiple improvements have been developed in the facility semi-span test capability. The primary purpose of the investigations was to assess Reynolds number scale effects on a modern commercial transport configuration up to full-scale flight test conditions (Reynolds numbers on the order of 27 million). The tests included longitudinal aerodynamic studies at subsonic takeoff and landing conditions across a range of Reynolds numbers from that available in conventional wind tunnels up to flight conditions. The purpose of this paper is to discuss lessons learned and improvements incorporated into the semi-span testing process. Topics addressed include enhanced thermal stabilization and moisture reduction procedures, assessments and improvements in model sealing techniques, compensation of model reference dimensions due to test temperature, significantly improved semi-span model access capability, and assessments of data repeatability.

A dual task priming investigation of right hemisphere inhibition for people with left hemisphere lesions

PubMed Central

2012-01-01

Background During normal semantic processing, the left hemisphere (LH) is suggested to restrict right hemisphere (RH) performance via interhemispheric suppression. However, a lesion in the LH or the use of concurrent tasks to overload the LH's attentional resource balance has been reported to result in RH disinhibition with subsequent improvements in RH performance. The current study examines variations in RH semantic processing in the context of unilateral LH lesions and the manipulation of the interhemispheric processing resource balance, in order to explore the relevance of RH disinhibition to hemispheric contributions to semantic processing following a unilateral LH lesion. Methods RH disinhibition was examined for nine participants with a single LH lesion and 13 matched controls using the dual task paradigm. Hemispheric performance on a divided visual field lexical decision semantic priming task was compared over three verbal memory load conditions, of zero-, two- and six-words. Related stimuli consisted of categorically related, associatively related, and categorically and associatively related prime-target pairs. Response time and accuracy data were recorded and analyzed using linear mixed model analysis, and planned contrasts were performed to compare priming effects in both visual fields, for each of the memory load conditions. Results Control participants exhibited significant bilateral visual field priming for all related conditions (p < .05), and a LH advantage over all three memory load conditions. Participants with LH lesions exhibited an improvement in RH priming performance as memory load increased, with priming for the categorically related condition occurring only in the 2- and 6-word memory conditions. RH disinhibition was also reflected for the LH damage (LHD) group by the removal of the LH performance advantage following the introduction of the memory load conditions. Conclusions The results from the control group are consistent with suggestions of an age related hemispheric asymmetry reduction and indicate that in healthy aging compensatory bilateral activation may reduce the impact of inhibition. In comparison, the results for the LHD group indicate that following a LH lesion RH semantic processing can be manipulated and enhanced by the introduction of a verbal memory task designed to engage LH resources and allow disinhibition of RH processing. PMID:22429687

E-learning process maturity level: a conceptual framework

NASA Astrophysics Data System (ADS)

Rahmah, A.; Santoso, H. B.; Hasibuan, Z. A.

2018-03-01

ICT advancement is a sure thing with the impact influencing many domains, including learning in both formal and informal situations. It leads to a new mindset that we should not only utilize the given ICT to support the learning process, but also improve it gradually involving a lot of factors. These phenomenon is called e-learning process evolution. Accordingly, this study attempts to explore maturity level concept to provide the improvement direction gradually and progression monitoring for the individual e-learning process. Extensive literature review, observation, and forming constructs are conducted to develop a conceptual framework for e-learning process maturity level. The conceptual framework consists of learner, e-learning process, continuous improvement, evolution of e-learning process, technology, and learning objectives. Whilst, evolution of e-learning process depicted as current versus expected conditions of e-learning process maturity level. The study concludes that from the e-learning process maturity level conceptual framework, it may guide the evolution roadmap for e-learning process, accelerate the evolution, and decrease the negative impact of ICT. The conceptual framework will be verified and tested in the future study.

Improved shelf life of dried Beauveria bassiana blastospores using convective drying and active packaging processes

USDA-ARS?s Scientific Manuscript database

The yeast form (blastospore) of the dimorphic insect-pathogenic fungus Beauveria bassiana can be rapidly produced using liquid fermentation methods but is generally unable to survive rapid dehydration processes or storage under non-refrigerated conditions. In this study, we evaluated the influence o...

The dynamic nature of the reconsolidation process and its boundary conditions: Evidence based on human tests.

PubMed

Fernández, Rodrigo S; Bavassi, Luz; Forcato, Cecilia; Pedreira, María E

2016-04-01

The reconsolidation process is the mechanism by which the strength and/or content of consolidated memories are updated. This process is triggered by the presentation of a reminder (training cues). It is not always possible to trigger the reconsolidation process. For example, memory age and strength are boundary conditions for the reconsolidation process. Here, we investigated the dynamic changes in these conditions. We propose that the boundary conditions of the reconsolidation process are not fixed and vary as a consequence of the interaction between memory features and reminder characteristics. To modify memory properties, participants received a threatening social protocol that improves memory acquisition or a control condition (fake, without social interaction) prior to learning pairs of meaningless syllables. To determine whether a strong young or old declarative memory undergoes the reconsolidation process, we used an interference task (a second list of pairs of meaningless syllables) to disrupt memory re-stabilization. To assess whether the older memory could be strengthened, we repeated the triggering of reconsolidation. Strong young or old memories modulated by a threatening experience could be interfered during reconsolidation and updated (strengthened) by reconsolidation. Rather than being fixed, boundary conditions vary according to the memory features (strong memory), which indicates the dynamic nature of the reconsolidation process. Our findings demonstrate that it is possible to modify these limits by recruiting the reconsolidation process and making it functionally operative again. This novel scenario opens the possibility to new therapeutically approaches that take into account the reconsolidation process. Copyright © 2016 Elsevier Inc. All rights reserved.

Attention-shift vs. response-priming explanations for the spatial cueing effect in cross-modal tasks.

PubMed

Paavilainen, Petri; Illi, Janne; Moisseinen, Nella; Niinisalo, Maija; Ojala, Karita; Reinikainen, Johanna; Vainio, Lari

2016-06-01

The task-irrelevant spatial location of a cue stimulus affects the processing of a subsequent target. This "Posner effect" has been explained by an exogenous attention shift to the spatial location of the cue, improving perceptual processing of the target. We studied whether the left/right location of task-irrelevant and uninformative tones produces cueing effects on the processing of visual targets. Tones were presented randomly from left or right. In the first condition, the subsequent visual target, requiring response either with the left or right hand, was presented peripherally to left or right. In the second condition, the target was a centrally presented left/right-pointing arrow, indicating the response hand. In the third condition, the tone and the central arrow were presented simultaneously. Data were recorded on compatible (the tone location and the response hand were the same) and incompatible trials. Reaction times were longer on incompatible than on compatible trials. The results of the second and third conditions are difficult to explain with the attention-shift model emphasizing improved perceptual processing in the cued location, as the central target did not require any location-based processing. Consequently, as an alternative explanation they suggest response priming in the hand corresponding to the spatial location of the tone. Simultaneous lateralized readiness potential (LRP) recordings were consistent with the behavioral data, the tone cues eliciting on incompatible trials a fast preparation for the incorrect response and on compatible trials preparation for the correct response. © 2016 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

19 CFR 10.198b - Products of Puerto Rico processed in a beneficiary country.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 19 Customs Duties 1 2014-04-01 2014-04-01 false Products of Puerto Rico processed in a beneficiary... Basin Initiative § 10.198b Products of Puerto Rico processed in a beneficiary country. Except in the... of Puerto Rico and that is by any means advanced in value or improved in condition in a beneficiary...

19 CFR 10.198b - Products of Puerto Rico processed in a beneficiary country.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 19 Customs Duties 1 2012-04-01 2012-04-01 false Products of Puerto Rico processed in a beneficiary... Basin Initiative § 10.198b Products of Puerto Rico processed in a beneficiary country. Except in the... of Puerto Rico and that is by any means advanced in value or improved in condition in a beneficiary...

19 CFR 10.198b - Products of Puerto Rico processed in a beneficiary country.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 19 Customs Duties 1 2013-04-01 2013-04-01 false Products of Puerto Rico processed in a beneficiary... Basin Initiative § 10.198b Products of Puerto Rico processed in a beneficiary country. Except in the... of Puerto Rico and that is by any means advanced in value or improved in condition in a beneficiary...

19 CFR 10.198b - Products of Puerto Rico processed in a beneficiary country.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Products of Puerto Rico processed in a beneficiary... Basin Initiative § 10.198b Products of Puerto Rico processed in a beneficiary country. Except in the... of Puerto Rico and that is by any means advanced in value or improved in condition in a beneficiary...

19 CFR 10.198b - Products of Puerto Rico processed in a beneficiary country.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Products of Puerto Rico processed in a beneficiary... Basin Initiative § 10.198b Products of Puerto Rico processed in a beneficiary country. Except in the... of Puerto Rico and that is by any means advanced in value or improved in condition in a beneficiary...

Simulation of Water Gas Shift Zeolite Membrane Reactor

NASA Astrophysics Data System (ADS)

Makertiharta, I. G. B. N.; Rizki, Z.; Zunita, Megawati; Dharmawijaya, P. T.

2017-07-01

The search of alternative energy sources keeps growing from time to time. Various alternatives have been introduced to reduce the use of fossil fuel, including hydrogen. Many pathways can be used to produce hydrogen. Among all of those, the Water Gas Shift (WGS) reaction is the most common pathway to produce high purity hydrogen. The WGS technique faces a downstream processing challenge due to the removal hydrogen from the product stream itself since it contains a mixture of hydrogen, carbon dioxide and also the excess reactants. An integrated process using zeolite membrane reactor has been introduced to improve the performance of the process by selectively separate the hydrogen whilst boosting the conversion. Furthermore, the zeolite membrane reactor can be further improved via optimizing the process condition. This paper discusses the simulation of Zeolite Membrane Water Gas Shift Reactor (ZMWGSR) with variation of process condition to achieve an optimum performance. The simulation can be simulated into two consecutive mechanisms, the reaction prior to the permeation of gases through the zeolite membrane. This paper is focused on the optimization of the process parameters (e.g. temperature, initial concentration) and also membrane properties (e.g. pore size) to achieve an optimum product specification (concentration, purity).

The line roughness improvement with plasma coating and cure treatment for 193nm lithography and beyond

NASA Astrophysics Data System (ADS)

Zheng, Erhu; Huang, Yi; Zhang, Haiyang

2017-03-01

As CMOS technology reaches 14nm node and beyond, one of the key challenges of the extension of 193nm immersion lithography is how to control the line edge and width roughness (LER/LWR). For Self-aligned Multiple Patterning (SaMP), LER becomes larger while LWR becomes smaller as the process proceeds[1]. It means plasma etch process becomes more and more dominant for LER reduction. In this work, we mainly focus on the core etch solution including an extra plasma coating process introduced before the bottom anti reflective coating (BARC) open step, and an extra plasma cure process applied right after BARC-open step. Firstly, we leveraged the optimal design experiment (ODE) to investigate the impact of plasma coating step on LER and identified the optimal condition. ODE is an appropriate method for the screening experiments of non-linear parameters in dynamic process models, especially for high-cost-intensive industry [2]. Finally, we obtained the proper plasma coating treatment condition that has been proven to achieve 32% LER improvement compared with standard process. Furthermore, the plasma cure scheme has been also optimized with ODE method to cover the LWR degradation induced by plasma coating treatment.

Advanced multivariable control of a turboexpander plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Altena, D.; Howard, M.; Bullin, K.

1998-12-31

This paper describes an application of advanced multivariable control on a natural gas plant and compares its performance to the previous conventional feed-back control. This control algorithm utilizes simple models from existing plant data and/or plant tests to hold the process at the desired operating point in the presence of disturbances and changes in operating conditions. The control software is able to accomplish this due to effective handling of process variable interaction, constraint avoidance and feed-forward of measured disturbances. The economic benefit of improved control lies in operating closer to the process constraints while avoiding significant violations. The South Texasmore » facility where this controller was implemented experienced reduced variability in process conditions which increased liquids recovery because the plant was able to operate much closer to the customer specified impurity constraint. An additional benefit of this implementation of multivariable control is the ability to set performance criteria beyond simple setpoints, including process variable constraints, relative variable merit and optimizing use of manipulated variables. The paper also details the control scheme applied to the complex turboexpander process and some of the safety features included to improve reliability.« less

An approach of point cloud denoising based on improved bilateral filtering

NASA Astrophysics Data System (ADS)

Zheng, Zeling; Jia, Songmin; Zhang, Guoliang; Li, Xiuzhi; Zhang, Xiangyin

2018-04-01

An omnidirectional mobile platform is designed for building point cloud based on an improved filtering algorithm which is employed to handle the depth image. First, the mobile platform can move flexibly and the control interface is convenient to control. Then, because the traditional bilateral filtering algorithm is time-consuming and inefficient, a novel method is proposed which called local bilateral filtering (LBF). LBF is applied to process depth image obtained by the Kinect sensor. The results show that the effect of removing noise is improved comparing with the bilateral filtering. In the condition of off-line, the color images and processed images are used to build point clouds. Finally, experimental results demonstrate that our method improves the speed of processing time of depth image and the effect of point cloud which has been built.

The healthy learner model for student chronic condition management--part I.

PubMed

Erickson, Cecelia DuPlessis; Splett, Patricia L; Mullett, Sara Stoltzfus; Heiman, Mary Bielski

2006-12-01

A significant number of children have chronic health conditions that interfere with normal activities, including school attendance and active participation in the learning process. Management of students' chronic conditions is complex and requires an integrated system. Models to improve chronic disease management have been developed for the medical system and public health. Programs that address specific chronic disease management or coordinate school health services have been implemented in schools. Lacking is a comprehensive, integrated model that links schools, students, parents, health care, and other community providers. The Healthy Learner Model for chronic condition management identifies seven elements for creating, implementing, and sustaining an efficient and effective, comprehensive community-based system for improving the management of chronic conditions for school children. It has provided the framework for successful chronic condition management in an urban school district and is proposed for replication in other districts and communities.

Defense Facility Condition: Revised Guidance Needed to Improve Oversight of Assessments and Ratings

DTIC Science & Technology

2016-06-01

are to implement the standardized process in part by assessing the condition of buildings, pavement , and rail using the same set of software tools...facility to current standards; costs for labor, equipment, materials, and currency exchange rates overseas; costs for project planning and design ...example, the services are to assess the condition of buildings, pavement , and rail using Sustainment Management System software tools developed by the

Lignocellulosic ethanol production at high-gravity: challenges and perspectives.

PubMed

Koppram, Rakesh; Tomás-Pejó, Elia; Xiros, Charilaos; Olsson, Lisbeth

2014-01-01

In brewing and ethanol-based biofuel industries, high-gravity fermentation produces 10-15% (v/v) ethanol, resulting in improved overall productivity, reduced capital cost, and reduced energy input compared to processing at normal gravity. High-gravity technology ensures a successful implementation of cellulose to ethanol conversion as a cost-competitive process. Implementation of such technologies is possible if all process steps can be performed at high biomass concentrations. This review focuses on challenges and technological efforts in processing at high-gravity conditions and how these conditions influence the physiology and metabolism of fermenting microorganisms, the action of enzymes, and other process-related factors. Lignocellulosic materials add challenges compared to implemented processes due to high inhibitors content and the physical properties of these materials at high gravity. Copyright © 2013 Elsevier Ltd. All rights reserved.

Efficiency improvement of technological preparation of power equipment manufacturing

NASA Astrophysics Data System (ADS)

Milukov, I. A.; Rogalev, A. N.; Sokolov, V. P.; Shevchenko, I. V.

2017-11-01

Competitiveness of power equipment primarily depends on speeding-up the development and mastering of new equipment samples and technologies, enhancement of organisation and management of design, manufacturing and operation. Actual political, technological and economic conditions cause the acute need in changing the strategy and tactics of process planning. At that the issues of maintenance of equipment with simultaneous improvement of its efficiency and compatibility to domestically produced components are considering. In order to solve these problems, using the systems of computer-aided process planning for process design at all stages of power equipment life cycle is economically viable. Computer-aided process planning is developed for the purpose of improvement of process planning by using mathematical methods and optimisation of design and management processes on the basis of CALS technologies, which allows for simultaneous process design, process planning organisation and management based on mathematical and physical modelling of interrelated design objects and production system. An integration of computer-aided systems providing the interaction of informative and material processes at all stages of product life cycle is proposed as effective solution to the challenges in new equipment design and process planning.

Interface conditions of two-shot molded parts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kisslinger, Thomas, E-mail: thomas.kisslinger@pccl.at; Bruckmoser, Katharina, E-mail: katharina.bruckmoser@unileoben.ac.at; Resch, Katharina, E-mail: katharina.resch@unileoben.ac.at

2014-05-15

The focus of this work is on interfaces of two-shot molded parts. It is well known that e.g. material combination, process parameters and contact area structures show significant effects on the bond strength of multi-component injection molded parts. To get information about the bond strength at various process parameter settings and material combinations a test mold with core back technology was used to produce two-component injection molded tensile test specimens. At the core back process the different materials are injected consecutively, so each component runs through the whole injection molding cycle (two-shot process). Due to this consecutive injection molding processes,more » a cold interface is generated. This is defined as overmolding of a second melt to a solidified polymer preform. Strong interest lies in the way the interface conditions change during the adhesion formation between the individual components. Hence the interface conditions were investigated by computed tomography and Raman spectroscopy. By analyzing these conditions the understanding of the adhesion development during the multi-component injection molding was improved.« less

Integrative medicine for chronic pain: A cohort study using a process-outcome design in the context of a department for internal and integrative medicine.

PubMed

Saha, Felix J; Brüning, Alexander; Barcelona, Cyrus; Büssing, Arndt; Langhorst, Jost; Dobos, Gustav; Lauche, Romy; Cramer, Holger

2016-07-01

Integrative medicine inpatient treatment has been shown to improve physical and mental health in patients with internal medicine conditions. The aim of this study was to investigate the effectiveness of a 2-week integrative medicine inpatient treatment in patients with chronic pain syndromes and the association of treatment success with patient-related process variables. Inpatients with chronic pain syndromes participating in a 2-week integrative medicine inpatient program were included. Patients' pain intensity, pain disability, pain perception, quality of life, depression, and perceived stress were measured on admission, discharge, and 6 months after discharge. Likewise process variables including ability and will to change, emotional/rational disease acceptance, mindfulness, life and health satisfaction, and easiness of life were assessed. A total of 310 inpatients (91% female, mean age 50.7 ± 12.4 year, 26.5% low back pain, and 22.9% fibromyalgia) were included. Using mixed linear models, significant improvements in pain intensity, pain disability, pain perception, quality of life, depression, and perceived stress were found (all P < 0.05). Ability to change and implementation, disease acceptance, mindfulness, life and health satisfaction, and light heartedness/easiness likewise improved (all P < 0.05). Improved outcomes were associated with increases in process variables, mainly ability to change and implementation, disease acceptance, life and health satisfaction, and light heartedness/easiness (R = 0.03-0.40). Results of this study suggest that a 2-week integrative medicine inpatient treatment can benefit patients with chronic pain conditions. Functional improvements are associated with improved ability to change and implementation, disease acceptance, and satisfaction.

Fontan Surgical Planning: Previous Accomplishments, Current Challenges, and Future Directions.

PubMed

Trusty, Phillip M; Slesnick, Timothy C; Wei, Zhenglun Alan; Rossignac, Jarek; Kanter, Kirk R; Fogel, Mark A; Yoganathan, Ajit P

2018-04-01

The ultimate goal of Fontan surgical planning is to provide additional insights into the clinical decision-making process. In its current state, surgical planning offers an accurate hemodynamic assessment of the pre-operative condition, provides anatomical constraints for potential surgical options, and produces decent post-operative predictions if boundary conditions are similar enough between the pre-operative and post-operative states. Moving forward, validation with post-operative data is a necessary step in order to assess the accuracy of surgical planning and determine which methodological improvements are needed. Future efforts to automate the surgical planning process will reduce the individual expertise needed and encourage use in the clinic by clinicians. As post-operative physiologic predictions improve, Fontan surgical planning will become an more effective tool to accurately model patient-specific hemodynamics.

The need to improve health care in prisons

PubMed Central

Fernandes, Luiz Henrique; Alvarenga, Carlos Willie; dos Santos, Luciane Loures; Pazin, Antonio

2014-01-01

OBJECTIVE To analyze physical structure, working conditions of health professionals and outline of the procedures established in prisons. METHODS We analyzed 34 provisional detention centers and 69 male and six female prison units in the state of Sao Paulo, Southeastern Brazil, in 2009. A self-applied instrument was developed to collect quantitative data on the characteristics of health care structure, equipment and personnel in prisons. Analysis of variance (ANOVA) or equivalent non-parametric tests and Chi-square or Fisher’s tests were used to compare categorical and continuous variables, respectively, between the groups. RESULTS The main problems were delays in the results of laboratory tests and imaging. With respect to the teams, it was observed that a large majority were in conditions close to those proposed by the Bipartite Commission 2013 but without improvement being reflected in the indicators. With respect to the process, more than 60.0% of prisons located in small towns do not have the structural conditions to ensure secondary or tertiary health care for the continuity of treatment. CONCLUSIONS This profile of prisons in the country can be used for planning and monitoring future actions for the continuous improvement of healthcare processes. PMID:24897049

Fluidised-bed spray-drying formulations of Candida sake CPA-1 by adding biodegradable coatings to enhance their survival under stress conditions.

PubMed

Carbó, Anna; Torres, Rosario; Usall, Josep; Solsona, Cristina; Teixidó, Neus

2017-11-01

The biocontrol agent Candida sake CPA-1 has demonstrated to be effective against several diseases on fruit. However, for application of CPA-1 under field conditions, it was necessary to mix it with a food coating to improve survival under stress conditions, as well as adherence and distribution on fruit surfaces. The objective of this study was to obtain a more competitive formulation under field conditions to be applied independently of any product. To achieve this purpose, the drying process of CPA-1 by a fluidised-bed spray-drying system together with biodegradable coatings was optimised. This approach is novel for the drying system used and the formulation obtained which was able to form a film or coating on fruit surfaces. Several substances were tested as carriers and binders, and drying temperature was optimised. The addition of protective compounds was also tested to improve survival of CPA-1 during the dehydration process. Product shelf life, biocontrol efficacy on grapes against Botrytis cinerea, and the improvement of C. sake behaviour under stress conditions were tested. The optimal temperature of drying was 55 °C and two formulations that were able to develop a coating on fruit surfaces were obtained. One of the formulations was created by using a combination of native and pregelatinised potato starch; the other formulation was obtained using maltodextrin and by adding skimmed milk and sucrose as protectant compounds. The formulated products reduced the incidence and severity of B. cinerea, and CPA-1 survival rate was increased under stress conditions of temperature and humidity.

Assessing Engineering Competencies: The Conditions for Educational Improvement

ERIC Educational Resources Information Center

Musekamp, Frank; Pearce, Jacob

2015-01-01

Low-stakes assessment is supposed to improve educational practice by providing feedback to different actors in educational systems. However, the process of assessment from design to the point of a final impact on student learning outcomes is complex and diverse. It is hard to identify reasons for substandard achievement on assessments, let alone…

Role of oxidants in enhancing dewaterability of anaerobically digested sludge through Fe (II) activated oxidation processes: hydrogen peroxide versus persulfate

PubMed Central

Song, Kang; Zhou, Xu; Liu, Yiqi; Gong, Yanyan; Zhou, Beibei; Wang, Dongbo; Wang, Qilin

2016-01-01

Improving dewaterability of sludge is important for the disposal of sludge in wastewater treatment plants (WWTPs). This study, for the first time, investigated the Fe(II) activated oxidization processes in improving anaerobically digested sludge (ADS) dewaterability. The combination of Fe(II) (0–100 mg/g total solids (TS)) and persulfate (0–1,000 mg/g TS) under neutral pH as well as the combination of Fe(II) (0–100 mg/g TS) and hydrogen peroxide (HP) (0–1,000 mg/g TS) under pH 3.0 were used to examine and compare their effect on the ADS dewaterability enhancement. The highest ADS dewaterability enhancement was attained at 25 mg Fe(II)/g TS and 50 mg HP/g TS, when the CST (CST: the capillary suction time, a sludge dewaterability indicator) was reduced by 95%. In contrast, the highest CST reduction in Fe(II)-persulfate conditioning was 90%, which was obtained at 50 mg Fe(II)/g TS and 250 mg persulfate/g TS. The results showed that Fe(II)-HP conditioning was comparable with Fe(II)-persulfate conditioning in terms of highest CST reduction. Economic analysis suggested that the Fe(II)-HP conditioning was more promising for improving ADS dewaterability compared with Fe(II)-persulfate conditioning, with the saving being up to $65,000 per year in a WWTP with a population equivalent of 100,000. PMID:27109500

Fatigue Performance of Powder Metallurgy (PM) Ti-6Al-4V Alloy: A Critical Analysis of Current Fatigue Data and Metallurgical Approaches for Improving Fatigue Strength

NASA Astrophysics Data System (ADS)

Cao, Fei; Ravi Chandran, K. S.

2016-03-01

A comprehensive assessment of fatigue performance of powder metallurgy (PM) Ti-6Al-4V alloy, manufactured using various powder-based processing approaches to-date, is performed in this work. The focus is on PM processes that use either blended element (BE) or pre-alloyed (PA) powder as feedstock. Porosity and the microstructure condition have been found to be the two most dominant material variables that control the fatigue strength. The evaluation reveals that the fatigue performance of PM Ti-6Al-4V, in the as-sintered state, is far lower than that in the wrought condition. This is largely caused by residual porosity, even if it is present in small amounts, or, by the coarse lamellar colony microstructure. The fatigue strength is significantly improved by the closure of pores, and it approaches the levels of wrought Ti-6Al-4V alloys, after hot-isostatic-pressing (HIPing). Further thermo-mechanical and heat treatments lead to additional increases in fatigue strength-in one case, a high fatigue strength level, exceeding that of the mill-annealed condition, was achieved. The work identifies the powder, process and microstructure improvements that are necessary for achieving high fatigue strength in powder metallurgical Ti-6Al-4V alloys in order for them to effectively compete with wrought forms. The present findings, gathered from the traditional titanium powder metallurgy, are also directly applicable to additively manufactured titanium, because of the similarities in pores, defects, and microstructures between the two manufacturing processes.

Improved prediction of severe thunderstorms over the Indian Monsoon region using high-resolution soil moisture and temperature initialization

PubMed Central

Osuri, K. K.; Nadimpalli, R.; Mohanty, U. C.; Chen, F.; Rajeevan, M.; Niyogi, D.

2017-01-01

The hypothesis that realistic land conditions such as soil moisture/soil temperature (SM/ST) can significantly improve the modeling of mesoscale deep convection is tested over the Indian monsoon region (IMR). A high resolution (3 km foot print) SM/ST dataset prepared from a land data assimilation system, as part of a national monsoon mission project, showed close agreement with observations. Experiments are conducted with (LDAS) and without (CNTL) initialization of SM/ST dataset. Results highlight the significance of realistic land surface conditions on numerical prediction of initiation, movement and timing of severe thunderstorms as compared to that currently being initialized by climatological fields in CNTL run. Realistic land conditions improved mass flux, convective updrafts and diabatic heating in the boundary layer that contributed to low level positive potential vorticity. The LDAS run reproduced reflectivity echoes and associated rainfall bands more efficiently. Improper representation of surface conditions in CNTL run limit the evolution boundary layer processes and thereby failed to simulate convection at right time and place. These findings thus provide strong support to the role land conditions play in impacting the deep convection over the IMR. These findings also have direct implications for improving heavy rain forecasting over the IMR, by developing realistic land conditions. PMID:28128293

Processing of Aluminum-Graphite Particulate Metal Matrix Composites by Advanced Shear Technology

NASA Astrophysics Data System (ADS)

Barekar, N.; Tzamtzis, S.; Dhindaw, B. K.; Patel, J.; Hari Babu, N.; Fan, Z.

2009-12-01

To extend the possibilities of using aluminum/graphite composites as structural materials, a novel process is developed. The conventional methods often produce agglomerated structures exhibiting lower strength and ductility. To overcome the cohesive force of the agglomerates, a melt conditioned high-pressure die casting (MC-HPDC) process innovatively adapts the well-established, high-shear dispersive mixing action of a twin screw mechanism. The distribution of particles and properties of composites are quantitatively evaluated. The adopted rheo process significantly improved the distribution of the reinforcement in the matrix with a strong interfacial bond between the two. A good combination of improved ultimate tensile strength (UTS) and tensile elongation (ɛ) is obtained compared with composites produced by conventional processes.

Optimizing chemical conditioning for odour removal of undigested sewage sludge in drying processes.

PubMed

Vega, Esther; Monclús, Hèctor; Gonzalez-Olmos, Rafael; Martin, Maria J

2015-03-01

Emission of odours during the thermal drying in sludge handling processes is one of the main sources of odour problems in wastewater treatment plants. The objective of this work was to assess the use of the response surface methodology as a technique to optimize the chemical conditioning process of undigested sewage sludges, in order to improve the dewaterability, and to reduce the odour emissions during the thermal drying of the sludge. Synergistic effects between inorganic conditioners (iron chloride and calcium oxide) were observed in terms of sulphur emissions and odour reduction. The developed quadratic models indicated that optimizing the conditioners dosage is possible to increase a 70% the dewaterability, reducing a 50% and 54% the emission of odour and volatile sulphur compounds respectively. The optimization of the conditioning process was validated experimentally. Copyright © 2014 Elsevier Ltd. All rights reserved.

Multimodal exercise training in multiple sclerosis: A randomized controlled trial in persons with substantial mobility disability.

PubMed

Sandroff, Brian M; Bollaert, Rachel E; Pilutti, Lara A; Peterson, Melissa L; Baynard, Tracy; Fernhall, Bo; McAuley, Edward; Motl, Robert W

2017-10-01

Mobility disability is a common, debilitating feature of multiple sclerosis (MS). Exercise training has been identified as an approach to improve MS-related mobility disability. However, exercise randomized controlled trials (RCTs) on mobility in MS have generally not selectively targeted those with the onset of irreversible mobility disability. The current multi-site RCT compared the efficacy of 6-months of supervised, multimodal exercise training with an active control condition for improving mobility, gait, physical fitness, and cognitive outcomes in persons with substantial MS-related mobility disability. 83 participants with substantial MS-related mobility disability underwent initial mobility, gait, fitness, and cognitive processing speed assessments and were randomly assigned to 6-months of supervised multimodal (progressive aerobic, resistance, and balance) exercise training (intervention condition) or stretching-and-toning activities (control condition). Participants completed the same outcome assessments halfway through and immediately following the 6-month study period. There were statistically significant improvements in six-minute walk performance (F(2158)=3.12, p=0.05, η p 2 =0.04), peak power output (F(2150)=8.16, p<0.01, η p 2 =0.10), and Paced Auditory Serial Addition Test performance (F(2162)=4.67, p=0.01, η p 2 =0.05), but not gait outcomes, for those who underwent the intervention compared with those who underwent the control condition. This RCT provides novel, preliminary evidence that multimodal exercise training may improve endurance walking performance and cognitive processing speed, perhaps based on improvements in cardiorespiratory capacity, in persons with MS with substantial mobility disability. This is critical for informing the development of multi-site exercise rehabilitation programs in larger samples of persons with MS-related mobility disability. Copyright © 2017 Elsevier Inc. All rights reserved.

Manipulating environmental stresses and stress tolerance of microalgae for enhanced production of lipids and value-added products-A review.

PubMed

Chen, Bailing; Wan, Chun; Mehmood, Muhammad Aamer; Chang, Jo-Shu; Bai, Fengwu; Zhao, Xinqing

2017-11-01

Microalgae have promising potential to produce lipids and a variety of high-value chemicals. Suitable stress conditions such as nitrogen starvation and high salinity could stimulate synthesis and accumulation of lipids and high-value products by microalgae, therefore, various stress-modification strategies were developed to manipulate and optimize cultivation processes to enhance bioproduction efficiency. On the other hand, advancements in omics-based technologies have boosted the research to globally understand microalgal gene regulation under stress conditions, which enable further improvement of production efficiency via genetic engineering. Moreover, integration of multi-omics data, synthetic biology design, and genetic engineering manipulations exhibits a tremendous potential in the betterment of microalgal biorefinery. This review discusses the process manipulation strategies and omics studies on understanding the regulation of metabolite biosynthesis under various stressful conditions, and proposes genetic engineering of microalgae to improve bioproduction via manipulating stress tolerance. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Effects of Pre-processing Strategies for Pediatric Cochlear Implant Recipients

PubMed Central

Rakszawski, Bernadette; Wright, Rose; Cadieux, Jamie H.; Davidson, Lisa S.; Brenner, Christine

2016-01-01

Background Cochlear implants (CIs) have been shown to improve children’s speech recognition over traditional amplification when severe to profound sensorineural hearing loss is present. Despite improvements, understanding speech at low-level intensities or in the presence of background noise remains difficult. In an effort to improve speech understanding in challenging environments, Cochlear Ltd. offers pre-processing strategies that apply various algorithms prior to mapping the signal to the internal array. Two of these strategies include Autosensitivity Control™ (ASC) and Adaptive Dynamic Range Optimization (ADRO®). Based on previous research, the manufacturer’s default pre-processing strategy for pediatrics’ everyday programs combines ASC+ADRO®. Purpose The purpose of this study is to compare pediatric speech perception performance across various pre-processing strategies while applying a specific programming protocol utilizing increased threshold (T) levels to ensure access to very low-level sounds. Research Design This was a prospective, cross-sectional, observational study. Participants completed speech perception tasks in four pre-processing conditions: no pre-processing, ADRO®, ASC, ASC+ADRO®. Study Sample Eleven pediatric Cochlear Ltd. cochlear implant users were recruited: six bilateral, one unilateral, and four bimodal. Intervention Four programs, with the participants’ everyday map, were loaded into the processor with different pre-processing strategies applied in each of the four positions: no pre-processing, ADRO®, ASC, and ASC+ADRO®. Data Collection and Analysis Participants repeated CNC words presented at 50 and 70 dB SPL in quiet and HINT sentences presented adaptively with competing R-Space noise at 60 and 70 dB SPL. Each measure was completed as participants listened with each of the four pre-processing strategies listed above. Test order and condition were randomized. A repeated-measures analysis of variance (ANOVA) was used to compare each pre-processing strategy across group data. Critical differences were utilized to determine significant score differences between each pre-processing strategy for individual participants. Results For CNC words presented at 50 dB SPL, the group data revealed significantly better scores using ASC+ADRO® compared to all other pre-processing conditions while ASC resulted in poorer scores compared to ADRO® and ASC+ADRO®. Group data for HINT sentences presented in 70 dB SPL of R-Space noise revealed significantly improved scores using ASC and ASC+ADRO® compared to no pre-processing, with ASC+ADRO® scores being better than ADRO® alone scores. Group data for CNC words presented at 70 dB SPL and adaptive HINT sentences presented in 60 dB SPL of R-Space noise showed no significant difference among conditions. Individual data showed that the pre-processing strategy yielding the best scores varied across measures and participants. Conclusions Group data reveals an advantage with ASC+ADRO® for speech perception presented at lower levels and in higher levels of background noise. Individual data revealed that the optimal pre-processing strategy varied among participants; indicating that a variety of pre-processing strategies should be explored for each CI user considering his or her performance in challenging listening environments. PMID:26905529

Silicon solar cell process. Development, fabrication and analysis

NASA Technical Reports Server (NTRS)

Yoo, H. I.; Iles, P. A.; Tanner, D. P.

1978-01-01

Solar cells were fabricated from unconventional silicon sheets, and the performances were characterized with an emphasis on statistical evaluation. A number of solar cell fabrication processes were used and conversion efficiency was measured under AMO condition at 25 C. Silso solar cells using standard processing showed an average efficiency of about 9.6%. Solar cells with back surface field process showed about the same efficiency as the cells from standard process. Solar cells from grain boundary passivation process did not show any improvements in solar cell performance.

Process mapping as a framework for performance improvement in emergency general surgery.

PubMed

DeGirolamo, Kristin; D'Souza, Karan; Hall, William; Joos, Emilie; Garraway, Naisan; Sing, Chad Kim; McLaughlin, Patrick; Hameed, Morad

2017-12-01

Emergency general surgery conditions are often thought of as being too acute for the development of standardized approaches to quality improvement. However, process mapping, a concept that has been applied extensively in manufacturing quality improvement, is now being used in health care. The objective of this study was to create process maps for small bowel obstruction in an effort to identify potential areas for quality improvement. We used the American College of Surgeons Emergency General Surgery Quality Improvement Program pilot database to identify patients who received nonoperative or operative management of small bowel obstruction between March 2015 and March 2016. This database, patient charts and electronic health records were used to create process maps from the time of presentation to discharge. Eighty-eight patients with small bowel obstruction (33 operative; 55 nonoperative) were identified. Patients who received surgery had a complication rate of 32%. The processes of care from the time of presentation to the time of follow-up were highly elaborate and variable in terms of duration; however, the sequences of care were found to be consistent. We used data visualization strategies to identify bottlenecks in care, and they showed substantial variability in terms of operating room access. Variability in the operative care of small bowel obstruction is high and represents an important improvement opportunity in general surgery. Process mapping can identify common themes, even in acute care, and suggest specific performance improvement measures.

Process mapping as a framework for performance improvement in emergency general surgery.

PubMed

DeGirolamo, Kristin; D'Souza, Karan; Hall, William; Joos, Emilie; Garraway, Naisan; Sing, Chad Kim; McLaughlin, Patrick; Hameed, Morad

2018-02-01

Emergency general surgery conditions are often thought of as being too acute for the development of standardized approaches to quality improvement. However, process mapping, a concept that has been applied extensively in manufacturing quality improvement, is now being used in health care. The objective of this study was to create process maps for small bowel obstruction in an effort to identify potential areas for quality improvement. We used the American College of Surgeons Emergency General Surgery Quality Improvement Program pilot database to identify patients who received nonoperative or operative management of small bowel obstruction between March 2015 and March 2016. This database, patient charts and electronic health records were used to create process maps from the time of presentation to discharge. Eighty-eight patients with small bowel obstruction (33 operative; 55 nonoperative) were identified. Patients who received surgery had a complication rate of 32%. The processes of care from the time of presentation to the time of follow-up were highly elaborate and variable in terms of duration; however, the sequences of care were found to be consistent. We used data visualization strategies to identify bottlenecks in care, and they showed substantial variability in terms of operating room access. Variability in the operative care of small bowel obstruction is high and represents an important improvement opportunity in general surgery. Process mapping can identify common themes, even in acute care, and suggest specific performance improvement measures.

Improving the Quality of Hot Stamping Parts with Innovative Press Technology and Inline Process Control

NASA Astrophysics Data System (ADS)

Vollmer, R.; Palm, C.

2017-09-01

The increasing number of hot stamped parts in the automotive industry is challenging different process areas. This paper presents a method how to improve the production rates over the whole life cycle of a hot forming part. In the core element of a hot forming line, the hydraulic press, mainly two processing steps are performed. Forming and quenching of the sheet metal part. In addition to the forming operation, it is inevitable to optimize the quenching condition in the bottom dead centre in order to reach a fully martensitic structure and tight geometrical tolerances of the part. Deviations in the blank thickness, tool wear, polishing of classical tools impair the quenching condition and therefore the part quality over the time. A new press and tool design has been developed to counter this effect by providing homogenous contact pressure over the whole die. Especially with a multi cavity tool, the new method is advantageous. Test series have shown that the new tool and press concept can produce parts with a blank thickness of 1.0 mm within 8.0 s cycle time. The so called PCH flex principle makes it possible to produce such high output rates under reliable conditions.

[The industrial environment in the electric-furnace steel smelting, converter and open-hearth furnace methods of manufacturing manganese-alloyed steels].

PubMed

Karnaukh, N G; Petrov, G A; Gapon, V A; Poslednichenko, I P; Shmidt, S E

1992-01-01

Inspection of the environment in manganese-alloyed steel production showed inadequate hygienic conditions of the technological processes employed. Air was more polluted by manganese oxides during the oxygen-converter process though their highest concentrations, 38 times exceeding the MAS, appeared during the casting of steel. An electric furnace coated by dust-noise-proof material and gas cleaning is preferable from a hygienic point of view. The influence of unfavourable microclimate, intensive infrared irradiation and loud noise on workers necessitates automation and mechanization of the process in order to improve the working conditions.

7 CFR Exhibit A to Subpart B of... - Grant Agreement-Growth Management and Housing Planning for Approved Designated Energy Impacted Areas

Code of Federal Regulations, 2011 CFR

2011-01-01

... met; (iii) Problems, delays, or adverse conditions which will materially affect attainment of planned... process which will improve local conditions and alleviate problems associated with increased coal or... Grantee programs, projects, related activities, and problems. (b) The Grantee shall inform the Grantor as...

Influence of the coating process on the tribological conditions during cold forging with a MoS2 based lubricant

NASA Astrophysics Data System (ADS)

Lorenz, Robby; Hagenah, Hinnerk; Merklein, Marion

2018-05-01

Cold forging processes such as forward rod extrusion can be used to produce high quality components like connection rods, shafts and gears. The main advantages of these extruded components are sufficient surface quality, work hardening, compressive residual stresses and fatigue strength. Since one technical disadvantage of extruded components lies in the achievable tolerance classes, the improvement of these should be of crucial importance. For instance, the attainable workpiece accuracy and component quality can be influenced by adapting the tribological system in such a way that the resulting friction is specifically controlled in order to improve component forming. Lubricant modification is one practical way of adapting the tribological system to the requirements of the forming process. An industrial established and highly efficient lubricant system is the application of a zinc-phosphate conversion layer with a molybdenum disulfide-based lubricant. While offering many advantages, its tribological conditions seem to depend strongly on the layer weight and the application strategy. These parameters and the respective interdependencies have not been sufficiently investigated yet. In order to examine this, the tribological conditions depending on the layer weight are analyzed in greater detail using the Ring-Compression-Test (RCT). This tribometer provides a comparative representation of the forming conditions during cold forging. Furthermore, a potential dependency between the tribological conditions and two different coating techniques is analyzed. The latter are represented by the industrial standards dipping and dip-drumming.

Ecological and Toxicological Characteristics of Metalworking Fluids Used in Finishing Processing in Russian Federation

NASA Astrophysics Data System (ADS)

Grigoriev, S. N.; Bobrovskij, N. M.; Melnikov, P. A.; Bobrovskij, I. N.; Levitskih, O. O.

2017-05-01

Nowadays, metalworking fluids (MWF) in the design of technological processes in most cases are considered as mandatory persistant components despite the constant improvement of the technology of machining, tools and equipment. Three main functions of MWF: cooling, lubrication, waste chips removal - seems to be the essential condition for stable process. In most cases, cooling reduces wear of tool and improves the quality of the processed surface. The cooling characteristics of the MWF affect not only the heat capacity and thermal conductivity, but metal surfaces wettability and vaporization. If processing speed and temperature of the fluid are high then it may not be in direct contact with the surface of the tool due to low wettability or vapor blankets. Improvement of machining process with applying the MWF is accompanied with negative factors. Due to the high temperatures in the treatment area it is exposed to MWF vaporization. This article presents estimation of the applicable in Russian Federation MWF: fire risk, toxicological and environmental hazards.

What research tells us about knowledge transfer strategies to improve public health in low-income countries: a scoping review.

PubMed

Siron, Stéphanie; Dagenais, Christian; Ridde, Valéry

2015-11-01

This study describes the current state of research on knowledge transfer strategies to improve public health in low-income countries, to identify the knowledge gaps on this topic. In this scoping review, a descriptive and systematic process was used to analyse, for each article retained, descriptions of research context and methods, types of knowledge transfer activities and results reported. 28 articles were analysed. They dealt with the evaluation of transfer strategies that employed multiple activities, mostly targeting health professionals and women with very young children. Most often these studies used quantitative designs and measurements of instrumental use with some methodological shortcomings. Results were positive and suggested recommendations for improving professional practices, knowledge and health-related behaviours. The review highlights the great diversity of transfer strategies used, strategies and many conditions for knowledge use. The review provides specific elements for understanding the transfer processes in low-income countries and highlights the need for systematic evaluation of the conditions for research results utilization.

Expensive Enrichment

ERIC Educational Resources Information Center

Resnikoff, Marvin

1975-01-01

This article presents an economic analysis of the nuclear fuel reprocessing industry. It indicates that while environmental safety devices have improved the working conditions, they have also added ever-increasing costs to this necessary process. (MA)

Influence of processing on the microstructure and mechanical properties of 14YWT

DOE PAGES

Hoelzer, David T.; Unocic, Kinga A.; Sokolov, Mikhail A.; ...

2015-12-15

In this study, the investigation of the mechanical alloying (MA) conditions for producing the advanced oxide dispersion strengthened (ODS) 14YWT ferritic alloy led to significant improvements in balancing the strength, ductility and fracture toughness properties while still maintaining the salient microstructural features consisting of ultra-fine grains and high concentration of Y-, Ti- and O-enriched nanoclusters. The implemented changes to the processing conditions included reducing the contamination of the powder during ball milling, applying a pre-extrusion annealing treatment on the ball milled powder and exploring different extrusion temperatures at 850 °C (SM170 heat), 1000 °C (SM185) and 1150 °C (SM200). Themore » microstructural studies of the three 14YWT heats showed similarities in the dispersion of nanoclusters and sub-micron size grains, indicating the microstructure was insensitive to the different extrusion conditions. Compared to past 14YWT heats, the three new heats showed lower strength, but higher ductility levels between 25 and 800 °C and significantly higher fracture toughness values between 25 °C and 700 °C. The lower contamination levels of O, C and N achieved with improved ball milling conditions plus the slightly larger grain size were identified as important factors for improving the balance in mechanical properties of the three heats of 14YWT.« less

A simulation study of harmonics regeneration in noise reduction for electric and acoustic stimulation.

PubMed

Hu, Yi

2010-05-01

Recent research results show that combined electric and acoustic stimulation (EAS) significantly improves speech recognition in noise, and it is generally established that access to the improved F0 representation of target speech, along with the glimpse cues, provide the EAS benefits. Under noisy listening conditions, noise signals degrade these important cues by introducing undesired temporal-frequency components and corrupting harmonics structure. In this study, the potential of combining noise reduction and harmonics regeneration techniques was investigated to further improve speech intelligibility in noise by providing improved beneficial cues for EAS. Three hypotheses were tested: (1) noise reduction methods can improve speech intelligibility in noise for EAS; (2) harmonics regeneration after noise reduction can further improve speech intelligibility in noise for EAS; and (3) harmonics sideband constraints in frequency domain (or equivalently, amplitude modulation in temporal domain), even deterministic ones, can provide additional benefits. Test results demonstrate that combining noise reduction and harmonics regeneration can significantly improve speech recognition in noise for EAS, and it is also beneficial to preserve the harmonics sidebands under adverse listening conditions. This finding warrants further work into the development of algorithms that regenerate harmonics and the related sidebands for EAS processing under noisy conditions.

Understanding human uses and values in watershed analysis.

Treesearch

Roger D. Fight; Linda E. Kruger; Christopher Hansen-Murray; Arnold Holden; Dale Bays

2000-01-01

Watershed analysis is used as a tool to understand the functioning of aquatic and terrestrial ecosystem processes at the landscape scale and to assess opportunities to restore or improve those processes and associated watershed conditions. Assessing those opportunities correctly requires an understanding of how humans have interacted with the watershed in the past and...

Information Competencies and Their Implementation in the Educational Process of Polish Universities Exploratory Studies

ERIC Educational Resources Information Center

Tonakiewicz-Kolosowska, Anna; Socik, Iwona; Gajewska, Monika

2016-01-01

The authors present the development and perspectives of improving the quality of Information Literacy programmes in Polish technical universities, considering the Bologna Process and the general conditions of the Polish higher education system. The survey conducted in selected technical and medical universities provided an overview of changes…

Can Sensory Gallery Guides for Children with Sensory Processing Challenges Improve Their Museum Experience?

ERIC Educational Resources Information Center

Fletcher, Tina S.; Blake, Amanda B.; Shelffo, Kathleen E.

2018-01-01

Children routinely visit art museums as part of their educational experience and family time, many of them having special needs. The number of children diagnosed with autism and sensory processing disorders is increasing. These conditions may include heightened sensory "avoiding" or "seeking" behaviors that can interfere with a…

Enhanced degradation of phenolic compounds in coal gasification wastewater by a novel integration of micro-electrolysis with biological reactor (MEBR) under the micro-oxygen condition.

PubMed

Ma, Weiwei; Han, Yuxing; Xu, Chunyan; Han, Hongjun; Ma, Wencheng; Zhu, Hao; Li, Kun; Wang, Dexin

2018-03-01

The aim of this work was to study an integration of micro-electrolysis with biological reactor (MEBR) for strengthening removal of phenolic compounds in coal gasification wastewater (CGW). The results indicated MEBR achieved high efficiencies in removal of COD and phenolic compounds as well as improvement of biodegradability of CGW under the micro-oxygen condition. The integrated MEBR process was more favorable to improvement of the structural stability of activated sludge and biodiversity of specific functional microbial communities. Especially, Shewanella and Pseudomonas were enriched to accelerate the extracellular electron transfer, finally facilitating the degradation of phenolic compounds. Moreover, MEBR process effectively relieved passivation of Fe-C filler surface and prolonged lifespan of Fe-C filler. Accordingly, the synergetic effect between iron-carbon micro-electrolysis (ICME) and biological action played a significant role in performance of the integrated process. Therefore, the integrated MEBR was a promising practical process for enhancing CGW treatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Improvement of cloud stability, yield and β-carotene content of carrot juice by process modification.

PubMed

Yu, Li Juan; Rupasinghe, H P Vasantha

2013-10-01

This study investigated the effects of three processing factors, acid blanching, centrifugation and dynamic high pressure homogenization, on cloud stability of carrot juice. Results indicated that the optimum processing condition for stabilized carrot juice were with dynamic high pressure homogenization at 100 MPa combined with 2% citric acid blanching at 95-100  for 2 min followed by 2000 r/min centrifugation for 10 min. The improvement of juice yield was also investigated using a pre-treatment of three commercial enzymes: Pectinex 3XL® (pectinase), Celluclast 1.5 L® (cellulase) and Novozyme 188™ (β-glucosidase). The combination of 0.1 g/kg of Pectinex 3XL®, 0.1 g/kg of Celluclast 1.5 L® and 0.1 g/kg of Novozyme 188™ at 50  and pH 4.0 for 90 min was the most effective condition to improve carrot juice yield from 49% to 67%. The enzymatic treatment increased juice total soluble solids from 7.5 to 8.9°Brix and β-carotene content from 21.4 to 33.7 mg/kg.

Picturing survival memories: enhanced memory after fitness-relevant processing occurs for verbal and visual stimuli.

PubMed

Otgaar, Henry; Smeets, Tom; van Bergen, Saskia

2010-01-01

Recent studies have shown that processing words according to a survival scenario leads to superior retention relative to control conditions. Here, we examined whether a survival recall advantage could be elicited by using pictures. Furthermore, in Experiment 1, we were interested in whether survival processing also results in improved memory for details. Undergraduates rated the relevance of pictures in a survival, moving, or pleasantness scenario and were subsequently given a surprise free recall test. We found that survival processing yielded superior retention. We also found that distortions occurred more often in the survival condition than in the pleasantness condition. In Experiment 2, we directly compared the survival recall effect between pictures and words. A comparable survival recall advantage was found for pictures and words. The present findings support the idea that memory is enhanced by processing information in terms of fitness value, yet at the same time, the present results suggest that this may increase the risk for memory distortions.

19 CFR 10.450 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... improvement to sound working condition by one or more of the following processes: welding, flame spraying... (3) Enjoy the same factory warranty as such new goods; and (r) Self-produced material. “Self-produced...

Sensitivity Analysis and Optimization of Enclosure Radiation with Applications to Crystal Growth

NASA Technical Reports Server (NTRS)

Tiller, Michael M.

1995-01-01

In engineering, simulation software is often used as a convenient means for carrying out experiments to evaluate physical systems. The benefit of using simulations as 'numerical' experiments is that the experimental conditions can be easily modified and repeated at much lower cost than the comparable physical experiment. The goal of these experiments is to 'improve' the process or result of the experiment. In most cases, the computational experiments employ the same trial and error approach as their physical counterparts. When using this approach for complex systems, the cause and effect relationship of the system may never be fully understood and efficient strategies for improvement never utilized. However, it is possible when running simulations to accurately and efficiently determine the sensitivity of the system results with respect to simulation to accurately and efficiently determine the sensitivity of the system results with respect to simulation parameters (e.g., initial conditions, boundary conditions, and material properties) by manipulating the underlying computations. This results in a better understanding of the system dynamics and gives us efficient means to improve processing conditions. We begin by discussing the steps involved in performing simulations. Then we consider how sensitivity information about simulation results can be obtained and ways this information may be used to improve the process or result of the experiment. Next, we discuss optimization and the efficient algorithms which use sensitivity information. We draw on all this information to propose a generalized approach for integrating simulation and optimization, with an emphasis on software programming issues. After discussing our approach to simulation and optimization we consider an application involving crystal growth. This application is interesting because it includes radiative heat transfer. We discuss the computation of radiative new factors and the impact this mode of heat transfer has on our approach. Finally, we will demonstrate the results of our optimization.

Improving human object recognition performance using video enhancement techniques

NASA Astrophysics Data System (ADS)

Whitman, Lucy S.; Lewis, Colin; Oakley, John P.

2004-12-01

Atmospheric scattering causes significant degradation in the quality of video images, particularly when imaging over long distances. The principle problem is the reduction in contrast due to scattered light. It is known that when the scattering particles are not too large compared with the imaging wavelength (i.e. Mie scattering) then high spatial resolution information may be contained within a low-contrast image. Unfortunately this information is not easily perceived by a human observer, particularly when using a standard video monitor. A secondary problem is the difficulty of achieving a sharp focus since automatic focus techniques tend to fail in such conditions. Recently several commercial colour video processing systems have become available. These systems use various techniques to improve image quality in low contrast conditions whilst retaining colour content. These systems produce improvements in subjective image quality in some situations, particularly in conditions of haze and light fog. There is also some evidence that video enhancement leads to improved ATR performance when used as a pre-processing stage. Psychological literature indicates that low contrast levels generally lead to a reduction in the performance of human observers in carrying out simple visual tasks. The aim of this paper is to present the results of an empirical study on object recognition in adverse viewing conditions. The chosen visual task was vehicle number plate recognition at long ranges (500 m and beyond). Two different commercial video enhancement systems are evaluated using the same protocol. The results show an increase in effective range with some differences between the different enhancement systems.

Optimized ultra-high-pressure-assisted extraction of procyanidins from lychee pericarp improves the antioxidant activity of extracts.

PubMed

Zhang, Ruifen; Su, Dongxiao; Hou, Fangli; Liu, Lei; Huang, Fei; Dong, Lihong; Deng, Yuanyuan; Zhang, Yan; Wei, Zhencheng; Zhang, Mingwei

2017-08-01

To establish optimal ultra-high-pressure (UHP)-assisted extraction conditions for procyanidins from lychee pericarp, a response surface analysis method with four factors and three levels was adopted. The optimum conditions were as follows: 295 MPa pressure, 13 min pressure holding time, 16.0 mL/g liquid-to-solid ratio, and 70% ethanol concentration. Compared with conventional ethanol extraction and ultrasonic-assisted extraction methods, the yields of the total procyanidins, flavonoids, and phenolics extracted using the UHP process were significantly increased; consequently, the oxygen radical absorbance capacity and cellular antioxidant activity of UHP-assisted lychee pericarp extracts were substantially enhanced. LC-MS/MS and high-performance liquid chromatography quantification results for individual phenolic compounds revealed that the yield of procyanidin compounds, including epicatechin, procyanidin A2, and procyanidin B2, from lychee pericarp could be significantly improved by the UHP-assisted extraction process. This UHP-assisted extraction process is thus a practical method for the extraction of procyanidins from lychee pericarp.

Risk assessment of manual material handling activities (case study: PT BRS Standard Industry)

NASA Astrophysics Data System (ADS)

Deviani; Triyanti, V.

2017-12-01

The process of moving material manually has the potential for injury to workers. The risk of injury will increase if we do not pay attention to the working conditions. The purpose of this study is to assess and analyze the injury risk level in manual handling material activity, as well as to improve the condition. The observed manual material handling activities is pole lifting and goods loading. These activities were analyzed using Job Strain Index method, Rapid Entire Body Assessment, and Chaffin’s 2D Planar Static Model. The results show that most workers who perform almost all activities have a high level of risk level with the score of JSI and REBA exceeds 9 points. For some activities, the estimated compression forces in the lumbar area also exceed the standard limits of 3400 N. Concerning this condition, several suggestions for improvement were made, improving the composition of packing, improving body posture, and making guideline posters.

Challenges and potential improvements in the admission process of patients with spinal cord injury in a specialized rehabilitation clinic - an interview based qualitative study of an interdisciplinary team.

PubMed

Röthlisberger, Fabian; Boes, Stefan; Rubinelli, Sara; Schmitt, Klaus; Scheel-Sailer, Anke

2017-06-26

The admission process of patients to a hospital is the starting point for inpatient services. In order to optimize the quality of the health services provision, one needs a good understanding of the patient admission workflow in a clinic. The aim of this study was to identify challenges and potential improvements in the admission process of spinal cord injury patients at a specialized rehabilitation clinic from the perspective of an interdisciplinary team of health professionals. Semi-structured interviews with eight health professionals (medical doctors, physical therapists, occupational therapists, nurses) at the Swiss Paraplegic Centre (acute and rehabilitation clinic) were conducted based on a maximum variety purposive sampling strategy. The interviews were analyzed using a thematic analysis approach. The interviewees described the challenges and potential improvements in this admission process, focusing on five themes. First, the characteristics of the patient with his/her health condition and personality and his/her family influence different areas in the admission process. Improvements in the exchange of information between the hospital and the patient could speed up and simplify the admission process. In addition, challenges and potential improvements were found concerning the rehabilitation planning, the organization of the admission process and the interdisciplinary work. This study identified five themes of challenges and potential improvements in the admission process of spinal cord injury patients at a specialized rehabilitation clinic. When planning adaptations of process steps in one of the areas, awareness of effects in other fields is necessary. Improved pre-admission information would be a first important step to optimize the admission process. A common IT-system providing an interdisciplinary overview and possibilities for interdisciplinary exchange would support the management of the admission process. Managers of other hospitals can supplement the results of this study with their own process analyses, to improve their own patient admission processes.

The Role of Lug Preheating, Melt Pool Temperature, and Lug Entrance Delay on the Cast-on-Strap Joining Process

NASA Astrophysics Data System (ADS)

Pahlavan, Sohrab; Nikpour, Saman; Mirjalili, Mostafa; Alagheband, Ali; Azimi, Mohammadyousef; Taji, Iman

2017-07-01

This work deals with effective parameters in the cast-on-strap (COS) process during which grid lugs of a lead-acid battery are joined together by a strap. The effects of lug preheating, melt pool temperature, and lug entrance delay on the quality of joints and casting defects were investigated. Lug preheating was found to propitiously reduce joint internal voids because of flux elimination. Its adverse effect on lowering lug wettability, however, made it unfavorable under the experimental conditions. The melt pool temperature also showed a two-sided effect depending on the process conditions. Raising the temperature increases the strap melt fluidity, which improves the joint contact area; however, it has a negative effect on lug wettability by flux evaporation. Besides, higher temperatures cause more lug back-melting and, hence, lower relative contact lengths. Therefore, an intermediate temperature of 683 K (410 °C) was found to make the most proper condition. Moreover, the case at which the lugs enter the mold coincident with its filling by the melt rendered the best joint quality. In this condition, the melt flows through the interlug spaces, which helps the voids to escape, resulting in the better joint interface. As the conclusion, the lug entrance time has the most effective role on joint quality, considering that lug preheating does not show any improving effect.

No childhood development of viewpoint-invariant face recognition: evidence from 8-year-olds and adults.

PubMed

Crookes, Kate; Robbins, Rachel A

2014-10-01

Performance on laboratory face tasks improves across childhood, not reaching adult levels until adolescence. Debate surrounds the source of this development, with recent reviews suggesting that underlying face processing mechanisms are mature early in childhood and that the improvement seen on experimental tasks instead results from general cognitive/perceptual development. One face processing mechanism that has been argued to develop slowly is the ability to encode faces in a view-invariant manner (i.e., allowing recognition across changes in viewpoint). However, many previous studies have not controlled for general cognitive factors. In the current study, 8-year-olds and adults performed a recognition memory task with two study-test viewpoint conditions: same view (study front view, test front view) and change view (study front view, test three-quarter view). To allow quantitative comparison between children and adults, performance in the same view condition was matched across the groups by increasing the learning set size for adults. Results showed poorer memory in the change view condition than in the same view condition for both adults and children. Importantly, there was no quantitative difference between children and adults in the size of decrement in memory performance resulting from a change in viewpoint. This finding adds to growing evidence that face processing mechanisms are mature early in childhood. Copyright © 2014 Elsevier Inc. All rights reserved.

The effect of spatial auditory landmarks on ambulation.

PubMed

Karim, Adham M; Rumalla, Kavelin; King, Laurie A; Hullar, Timothy E

2018-02-01

The maintenance of balance and posture is a result of the collaborative efforts of vestibular, proprioceptive, and visual sensory inputs, but a fourth neural input, audition, may also improve balance. Here, we tested the hypothesis that auditory inputs function as environmental spatial landmarks whose effectiveness depends on sound localization ability during ambulation. Eight blindfolded normal young subjects performed the Fukuda-Unterberger test in three auditory conditions: silence, white noise played through headphones (head-referenced condition), and white noise played through a loudspeaker placed directly in front at 135 centimeters away from the ear at ear height (earth-referenced condition). For the earth-referenced condition, an additional experiment was performed where the effect of moving the speaker azimuthal position to 45, 90, 135, and 180° was tested. Subjects performed significantly better in the earth-referenced condition than in the head-referenced or silent conditions. Performance progressively decreased over the range from 0° to 135° but all subjects then improved slightly at the 180° compared to the 135° condition. These results suggest that presence of sound dramatically improves the ability to ambulate when vision is limited, but that sound sources must be located in the external environment in order to improve balance. This supports the hypothesis that they act by providing spatial landmarks against which head and body movement and orientation may be compared and corrected. Balance improvement in the azimuthal plane mirrors sensitivity to sound movement at similar positions, indicating that similar auditory mechanisms may underlie both processes. These results may help optimize the use of auditory cues to improve balance in particular patient populations. Copyright © 2017 Elsevier B.V. All rights reserved.

Relationships between lower tropospheric stability, low cloud cover, and water vapor isotopic composition in the subtropical Pacific

NASA Astrophysics Data System (ADS)

Galewsky, J.

2017-12-01

Understanding the processes that govern the relationships between lower tropospheric stability and low-cloud cover is crucial for improved constraints on low-cloud feedbacks and for improving the parameterizations of low-cloud cover used in climate models. The stable isotopic composition of atmospheric water vapor is a sensitive recorder of the balance of moistening and drying processes that set the humidity of the lower troposphere and may thus provide a useful framework for improving our understanding low-cloud processes. In-situ measurements of water vapor isotopic composition collected at the NOAA Mauna Loa Observatory in Hawaii, along with twice-daily soundings from Hilo and remote sensing of cloud cover, show a clear inverse relationship between the estimated inversion strength (EIS) and the mixing ratios and water vapor δ -values, and a positive relationship between EIS, deuterium excess, and Δ δ D, defined as the difference between an observation and a reference Rayleigh distillation curve. These relationships are consistent with reduced moistening and an enhanced upper-tropospheric contribution above the trade inversion under high EIS conditions and stronger moistening under weaker EIS conditions. The cloud fraction, cloud liquid water path, and cloud-top pressure were all found to be higher under low EIS conditions. Inverse modeling of the isotopic data for the highest and lowest terciles of EIS conditions provide quantitative constraints on the cold-point temperatures and mixing fractions that govern the humidity above the trade inversion. The modeling shows the moistening fraction between moist boundary layer air and dry middle tropospheric air 24±1.5% under low EIS conditions is and 6±1.5% under high EIS conditions. A cold-point (last-saturation) temperature of -30C can match the observations for both low and high EIS conditions. The isotopic composition of the moistening source as derived from the inversion (-114±10‰ ) requires moderate fractionation from a pure marine source, indicating a link between inversion strength and moistening of the lower troposphere from the outflow of shallow convection. This approach can be applied in other settings and the results can be used to test parameterizations in climate models.

Selenium Supplementation Affects Physiological and Biochemical Processes to Improve Fodder Yield and Quality of Maize (Zea mays L.) under Water Deficit Conditions

PubMed Central

Nawaz, Fahim; Naeem, Muhammad; Ashraf, Muhammad Y.; Tahir, Muhammad N.; Zulfiqar, Bilal; Salahuddin, Muhammad; Shabbir, Rana N.; Aslam, Muhammad

2016-01-01

Climate change is one of the most complex challenges that pose serious threats to livelihoods of poor people who rely heavily on agriculture and livestock particularly in climate-sensitive developing countries of the world. The negative effects of water scarcity, due to climate change, are not limited to productivity food crops but have far-reaching consequences on livestock feed production systems. Selenium (Se) is considered essential for animal health and has also been reported to counteract various abiotic stresses in plants, however, understanding of Se regulated mechanisms for improving nutritional status of fodder crops remains elusive. We report the effects of exogenous selenium supply on physiological and biochemical processes that may influence green fodder yield and quality of maize (Zea mays L.) under drought stress conditions. The plants were grown in lysimeter tanks under natural conditions and were subjected to normal (100% field capacity) and water stress (60% field capacity) conditions. Foliar spray of Se was carried out before the start of tasseling stage (65 days after sowing) and was repeated after 1 week, whereas, water spray was used as a control. Drought stress markedly reduced the water status, pigments and green fodder yield and resulted in low forage quality in water stressed maize plants. Nevertheless, exogenous Se application at 40 mg L-1 resulted in less negative leaf water potential (41%) and enhanced relative water contents (30%), total chlorophyll (53%), carotenoid contents (60%), accumulation of total free amino acids (40%) and activities of superoxide dismutase (53%), catalase (30%), peroxidase (27%), and ascorbate peroxidase (27%) with respect to control under water deficit conditions. Consequently, Se regulated processes improved fodder yield (15%) and increased crude protein (47%), fiber (10%), nitrogen free extract (10%) and Se content (36%) but did not affect crude ash content in water stressed maize plants. We propose that Se foliar spray (40 mg L-1) is a handy, feasible and cost-effective approach to improve maize fodder yield and quality in arid and semi-arid regions of the world facing acute shortage of water. PMID:27729917

Bootstrapping Process Improvement Metrics: CMMI Level 4 Process Improvement Metrics in a Level 3 World

NASA Technical Reports Server (NTRS)

Hihn, Jairus; Lewicki, Scott; Morgan, Scott

2011-01-01

The measurement techniques for organizations which have achieved the Software Engineering Institutes CMMI Maturity Levels 4 and 5 are well documented. On the other hand, how to effectively measure when an organization is Maturity Level 3 is less well understood, especially when there is no consistency in tool use and there is extensive tailoring of the organizational software processes. Most organizations fail in their attempts to generate, collect, and analyze standard process improvement metrics under these conditions. But at JPL, NASA's prime center for deep space robotic exploration, we have a long history of proving there is always a solution: It just may not be what you expected. In this paper we describe the wide variety of qualitative and quantitative techniques we have been implementing over the last few years, including the various approaches used to communicate the results to both software technical managers and senior managers.

24 CFR 241.505 - Processing of applications and required fees.

Code of Federal Regulations, 2012 CFR

2012-04-01

...-Supplemental Loans To Finance Purchase and Installation of Energy Conserving Improvements, Solar Energy Systems... condition to submission of an initial application for a firm commitment for insurance of an energy savings...

24 CFR 241.505 - Processing of applications and required fees.

Code of Federal Regulations, 2014 CFR

2014-04-01

...-Supplemental Loans To Finance Purchase and Installation of Energy Conserving Improvements, Solar Energy Systems... condition to submission of an initial application for a firm commitment for insurance of an energy savings...

24 CFR 241.505 - Processing of applications and required fees.

Code of Federal Regulations, 2013 CFR

2013-04-01

...-Supplemental Loans To Finance Purchase and Installation of Energy Conserving Improvements, Solar Energy Systems... condition to submission of an initial application for a firm commitment for insurance of an energy savings...

24 CFR 241.505 - Processing of applications and required fees.

Code of Federal Regulations, 2011 CFR

2011-04-01

...-Supplemental Loans To Finance Purchase and Installation of Energy Conserving Improvements, Solar Energy Systems... condition to submission of an initial application for a firm commitment for insurance of an energy savings...

24 CFR 241.505 - Processing of applications and required fees.

Code of Federal Regulations, 2010 CFR

2010-04-01

...-Supplemental Loans To Finance Purchase and Installation of Energy Conserving Improvements, Solar Energy Systems... condition to submission of an initial application for a firm commitment for insurance of an energy savings...

Gaze-controlled, computer-assisted communication in Intensive Care Unit: "speaking through the eyes".

PubMed

Maringelli, F; Brienza, N; Scorrano, F; Grasso, F; Gregoretti, C

2013-02-01

The aim of this study was to test the hypothesis that a gaze-controlled communication system (eye tracker, ET) can improve communication processes between completely dysarthric ICU patients and the hospital staff, in three main domains: 1) basic communication processes (i.e., fundamental needs, desire, and wishes); 2) the ability of the medical staff to understand the clinical condition of the patient; and 3) the level of frustration experienced by patient, nurses and physicians. Fifteen fully conscious medical and surgical patients, 8 physicians, and 15 nurses were included in the study. The experimental procedure was composed by three phases: in phase 1 all groups completed the preintervention questionnaire; in phase 2 the ET was introduced and tested as a communication device; in phase 3 all groups completed the postintervention questionnaire. Patients preintervention questionnaires showed remarkable communication deficits, without any group effect. Answers of physicians and nurses were pretty much similar to the one of patients. Postintervention questionnaires showed in all groups a remarkable and statistically significant improvement in different communication domains, as well as a remarkable decrease of anxiety and disphoric thought. Improvement was also reported by physicians and nurses in their ability to understand patient's clinical conditions. Our results show an improvement in the quality of the examined parameters. Better communication processes seem also to lead to improvements in several psychological parameters, namely anxiety and drop-out depression perceived by both patients and medical staff. Further controlled studies are needed to define the ET role in ICU.

1D and 2D oxidized carbon nanomaterials on epoxy matrix: performance of composites over the same processing conditions

NASA Astrophysics Data System (ADS)

Ramos-Galicia, Lourdes; Martinez-Hernandez, Ana Laura; Fuentes-Ramirez, Rosalba; Velasco-Santos, Carlos

2017-11-01

Oxidized multi-walled carbon nanotubes and graphene oxide were evaluated as reinforcements of an epoxy resin. The composites were synthesized at concentrations of 0.1, 0.5, and 1.0 wt% under the same processing conditions. Nanocomposites with graphene oxide at 0.5 wt% present the highest mechanical properties, reaching up to ~180%, and ~760% of improvement in tensile strength and tensile toughness with respect to neat epoxy. Nevertheless, composites with oxidized nanotubes exhibit a tendency to improve mechanical properties as load increases. Storage moduli diminish due to cross-linking density reduction in all nanocomposites. Difference in thermal degradation are not observed in composites in comparison with matrix. Dimension play an important role in mechanical properties, because each nanoreinforcement has different performance with the concentration.

Twelve evidence-based principles for implementing self-management support in primary care.

PubMed

Battersby, Malcolm; Von Korff, Michael; Schaefer, Judith; Davis, Connie; Ludman, Evette; Greene, Sarah M; Parkerton, Melissa; Wagner, Edward H

2010-12-01

Recommendations to improve self-management support and health outcomes for people with chronic conditions in primary care settings are provided on the basis of expert opinion supported by evidence for practices and processes. Practices and processes that could improve self-management support in primary care were identified through a nominal group process. In a targeted search strategy, reviews and meta-analyses were then identifed using terms from a wide range of chronic conditions and behavioral risk factors in combination with Self-Care, Self-Management, and Primary Care. On the basis of these reviews, evidence-based principles for self-management support were developed. The evidence is organized within the framework of the Chronic Care Model. Evidence-based principles in 12 areas were associated with improved patient self-management and/or health outcomes: (1) brief targeted assessment, (2) evidence-based information to guide shared decision-making, (3) use of a nonjudgmental approach, (4) collaborative priority and goal setting, (5) collaborative problem solving, (6) self-management support by diverse providers, (7) self-management interventions delivered by diverse formats, (8) patient self-efficacy, (9) active followup, (10) guideline-based case management for selected patients, (11) linkages to evidence-based community programs, and (12) multifaceted interventions. A framework is provided for implementing these principles in three phases of the primary care visit: enhanced previsit assessment, a focused clinical encounter, and expanded postvisit options. There is a growing evidence base for how self-management support for chronic conditions can be integrated into routine health care.

Integrative medicine for chronic pain

PubMed Central

Saha, Felix J.; Brüning, Alexander; Barcelona, Cyrus; Büssing, Arndt; Langhorst, Jost; Dobos, Gustav; Lauche, Romy; Cramer, Holger

2016-01-01

Abstract Introduction: Integrative medicine inpatient treatment has been shown to improve physical and mental health in patients with internal medicine conditions. The aim of this study was to investigate the effectiveness of a 2-week integrative medicine inpatient treatment in patients with chronic pain syndromes and the association of treatment success with patient-related process variables. Methods: Inpatients with chronic pain syndromes participating in a 2-week integrative medicine inpatient program were included. Patients’ pain intensity, pain disability, pain perception, quality of life, depression, and perceived stress were measured on admission, discharge, and 6 months after discharge. Likewise process variables including ability and will to change, emotional/rational disease acceptance, mindfulness, life and health satisfaction, and easiness of life were assessed. Results: A total of 310 inpatients (91% female, mean age 50.7 ± 12.4 year, 26.5% low back pain, and 22.9% fibromyalgia) were included. Using mixed linear models, significant improvements in pain intensity, pain disability, pain perception, quality of life, depression, and perceived stress were found (all P < 0.05). Ability to change and implementation, disease acceptance, mindfulness, life and health satisfaction, and light heartedness/easiness likewise improved (all P < 0.05). Improved outcomes were associated with increases in process variables, mainly ability to change and implementation, disease acceptance, life and health satisfaction, and light heartedness/easiness (R2 = 0.03–0.40). Conclusions: Results of this study suggest that a 2-week integrative medicine inpatient treatment can benefit patients with chronic pain conditions. Functional improvements are associated with improved ability to change and implementation, disease acceptance, and satisfaction. PMID:27399133

Mechanical and tribological behaviour of molten salt processed self-lubricated aluminium composite under different treatments

NASA Astrophysics Data System (ADS)

Kannan, C.; Ramanujam, R.

2018-05-01

The aim of this research work is to evaluate the mechanical and tribological behaviour of Al 7075 based self-lubricated hybrid nanocomposite under different treated conditions viz. as-cast, T6 and deep cryo treated. In order to overcome the drawbacks associated with conventional stir casting, a combinational approach that consists of molten salt processing, ultrasonic assistance and optimized mechanical stirring is adopted in this study to fabricate the nanocomposite. The mechanical characterisation tests carried out on this nanocomposite reveals an improvement of about 39% in hardness and 22% in ultimate tensile strength possible under T6 condition. Under specific conditions, the wear rate can be reduced to the extent of about 63% through the usage of self-lubricated hybrid nanocomposite under T6 condition.

Altitude acclimatization improves submaximal cognitive performance in mice and involves an imbalance of the cholinergic system.

PubMed

Guerra-Narbona, R; Delgado-García, J M; López-Ramos, J C

2013-06-15

The aim of this work was to reveal a hypothetical improvement of cognitive abilities in animals acclimatized to altitude and performing under ground level conditions, when looking at submaximal performance, once seen that it was not possible when looking at maximal scores. We modified contrasted cognitive tasks (object recognition, operant conditioning, eight-arm radial maze, and classical conditioning of the eyeblink reflex), increasing their complexity in an attempt to find performance differences in acclimatized animals vs. untrained controls. In addition, we studied, through immunohistochemical quantification, the expression of choline acetyltransferase and acetyl cholinesterase, enzymes involved in the synthesis and degradation of acetylcholine, in the septal area, piriform and visual cortexes, and the hippocampal CA1 area of animals submitted to acute hypobaric hypoxia, or acclimatized to this simulated altitude, to find a relationship between the cholinergic system and a cognitive improvement due to altitude acclimatization. Results showed subtle improvements of the cognitive capabilities of acclimatized animals in all of the tasks when performed under ground-level conditions (although not before 24 h), in the three tasks used to test explicit memory (object recognition, operant conditioning in the Skinner box, and eight-arm radial maze) and (from the first conditioning session) in the classical conditioning task used to evaluate implicit memory. An imbalance of choline acetyltransferase/acetyl cholinesterase expression was found in acclimatized animals, mainly 24 h after the acclimatization period. In conclusion, altitude acclimatization improves cognitive capabilities, in a process parallel to an imbalance of the cholinergic system.

Enhancement of wind stress evaluation method under storm conditions

NASA Astrophysics Data System (ADS)

Chen, Yingjian; Yu, Xiping

2016-12-01

Wind stress is an important driving force for many meteorological and oceanographical processes. However, most of the existing methods for evaluation of the wind stress, including various bulk formulas in terms of the wind speed at a given height and formulas relating the roughness height of the sea surface with wind conditions, predict an ever-increasing tendency of the wind stress coefficient as the wind speed increases, which is inconsistent with the field observations under storm conditions. The wave boundary layer model, which is based on the momentum and energy conservation, has the advantage to take into account the physical details of the air-sea interaction process, but is still invalid under storm conditions without a modification. By including the energy dissipation due to the presence of sea spray, which is speculated to be an important aspect of the air-sea interaction under storm conditions, the wave boundary layer model is improved in this study. The improved model is employed to estimate the wind stress caused by an idealized tropical cyclone motion. The computational results show that the wind stress coefficient reaches its maximal value at a wind speed of about 40 m/s and decreases as the wind speed further increases. This is in fairly good agreement with the field data.

Clustered Single Cellulosic Fiber Dissolution Kinetics and Mechanisms through Optical Microscopy under Limited Dissolving Conditions.

PubMed

Mäkelä, Valtteri; Wahlström, Ronny; Holopainen-Mantila, Ulla; Kilpeläinen, Ilkka; King, Alistair W T

2018-05-14

Herein, we describe a new method of assessing the kinetics of dissolution of single fibers by dissolution under limited dissolving conditions. The dissolution is followed by optical microscopy under limited dissolving conditions. Videos of the dissolution were processed in ImageJ to yield kinetics for dissolution, based on the disappearance of pixels associated with intact fibers. Data processing was performed using the Python language, utilizing available scientific libraries. The methods of processing the data include clustering of the single fiber data, identifying clusters associated with different fiber types, producing average dissolution traces and also extraction of practical parameters, such as, time taken to dissolve 25, 50, 75, 95, and 99.5% of the clustered fibers. In addition to these simple parameters, exponential fitting was also performed yielding rate constants for fiber dissolution. Fits for sample and cluster averages were variable, although demonstrating first-order kinetics for dissolution overall. To illustrate this process, two reference pulps (a bleached softwood kraft pulp and a bleached hardwood pre-hydrolysis kraft pulp) and their cellulase-treated versions were analyzed. As expected, differences in the kinetics and dissolution mechanisms between these samples were observed. Our initial interpretations are presented, based on the combined mechanistic observations and single fiber dissolution kinetics for these different samples. While the dissolution mechanisms observed were similar to those published previously, the more direct link of mechanistic information with the kinetics improve our understanding of cell wall structure and pre-treatments, toward improved processability.

Optimization of Surfactant Mixtures and Their Interfacial Behavior for Advanced Oil Recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Somasundaran, Prof. P.

2002-03-04

The objective of this project was to develop a knowledge base that is helpful for the design of improved processes for mobilizing and producing oil left untapped using conventional techniques. The main goal was to develop and evaluate mixtures of new or modified surfactants for improved oil recovery. In this regard, interfacial properties of novel biodegradable n-alkyl pyrrolidones and sugar-based surfactants have been studied systematically. Emphasis was on designing cost-effective processes compatible with existing conditions and operations in addition to ensuring minimal reagent loss.

On-line IR analyzer system to monitor cephamycin C loading on ion-exchange resin

NASA Astrophysics Data System (ADS)

Shank, Sheldon; Russ, Warren; Gravatt, Douglas; Lee, Wesley; Donahue, Steven M.

1992-08-01

An on-line infrared analyzer is being developed for monitoring cephamycin C loading on ion exchange resin. Accurate measurement of product loading offers productivity improvements with direct savings from product loss avoidance, minimized raw material cost, and reduced off-line laboratory testing. Ultrafiltered fermentation broth is fed onto ion exchange columns under conditions which adsorb the product, cephamycin C, to the resin while allowing impurities to pass unretained. Product loading is stopped when the on-line analyzer determines that resin capacity for adsorbing product is nearly exhausted. Infrared spectroscopy has been shown capable of quantifying cephamycin C in the process matrix at concentrations that support process control decisions. Process-to-analyzer interface challenges have been resolved, including sample conditioning requirements. Analyzer requirements have been defined. The sample conditioning station is under design.

Life cycle assessment as a tool for the environmental improvement of the tannery industry in developing countries.

PubMed

Rivela, B; Moreira, M T; Bornhardt, C; Méndez, R; Feijoo, G

2004-03-15

A representative leather tannery industry in a Latin American developing country has been studied from an environmental point of view, including both technical and economic analysis. Life Cycle Analysis (LCA) methodology has been used for the quantification and evaluation of the impacts of the chromium tanning process as a basis to propose further improvement actions. Four main subsystems were considered: beamhouse, tanyard, retanning, and wood furnace. Damages to human health, ecosystem quality, and resources are mainly produced by the tanyard subsystem. The control and reduction of chromium and ammonia emissions are the critical points to be considered to improve the environmental performance of the process. Technologies available for improved management of chromium tanning were profoundly studied, and improvement actions related to optimized operational conditions and a high exhaustion chrome-tanning process were selected. These actions related to the implementation of internal procedures affected the economy of the process with savings ranging from US dollars 8.63 to US dollars 22.5 for the processing of 1 ton of wet salt hides, meanwhile the global environmental impact was reduced to 44-50%. Moreover, the treatment of wastewaters was considered in two scenarios. Primary treatment presented the largest reduction of the environmental impact of the tanning process, while no significant improvement for the evaluated impact categories was achieved when combining primary and secondary treatments.

Safe patient handling in diagnostic imaging.

PubMed

Murphey, Susan L

2010-01-01

Raising awareness of the risk to diagnostic imaging personnel from manually lifting, transferring, and repositioning patients is critical to improving workplace safety and staff utilization. The aging baby boomer generation and growing bariatric population exacerbate the problem. Also, legislative initiatives are increasing nationwide for hospitals to implement safe patient handling programs. A management process designed to improve working conditions through implementing ergonomic programs can reduce losses and improve productivity and patient care outcome measures for imaging departments.

Improving vehicle tracking rate and speed estimation in dusty and snowy weather conditions with a vibrating camera

PubMed Central

Yaghoobi Ershadi, Nastaran

2017-01-01

Traffic surveillance systems are interesting to many researchers to improve the traffic control and reduce the risk caused by accidents. In this area, many published works are only concerned about vehicle detection in normal conditions. The camera may vibrate due to wind or bridge movement. Detection and tracking of vehicles is a very difficult task when we have bad weather conditions in winter (snowy, rainy, windy, etc.), dusty weather in arid and semi-arid regions, at night, etc. Also, it is very important to consider speed of vehicles in the complicated weather condition. In this paper, we improved our method to track and count vehicles in dusty weather with vibrating camera. For this purpose, we used a background subtraction based strategy mixed with an extra processing to segment vehicles. In this paper, the extra processing included the analysis of the headlight size, location, and area. In our work, tracking was done between consecutive frames via a generalized particle filter to detect the vehicle and pair the headlights using the connected component analysis. So, vehicle counting was performed based on the pairing result, with Centroid of each blob we calculated distance between two frames by simple formula and hence dividing it by the time between two frames obtained from the video. Our proposed method was tested on several video surveillance records in different conditions such as dusty or foggy weather, vibrating camera, and in roads with medium-level traffic volumes. The results showed that the new proposed method performed better than our previously published method and other methods, including the Kalman filter or Gaussian model, in different traffic conditions. PMID:29261719

Improving vehicle tracking rate and speed estimation in dusty and snowy weather conditions with a vibrating camera.

PubMed

Yaghoobi Ershadi, Nastaran

2017-01-01

Traffic surveillance systems are interesting to many researchers to improve the traffic control and reduce the risk caused by accidents. In this area, many published works are only concerned about vehicle detection in normal conditions. The camera may vibrate due to wind or bridge movement. Detection and tracking of vehicles is a very difficult task when we have bad weather conditions in winter (snowy, rainy, windy, etc.), dusty weather in arid and semi-arid regions, at night, etc. Also, it is very important to consider speed of vehicles in the complicated weather condition. In this paper, we improved our method to track and count vehicles in dusty weather with vibrating camera. For this purpose, we used a background subtraction based strategy mixed with an extra processing to segment vehicles. In this paper, the extra processing included the analysis of the headlight size, location, and area. In our work, tracking was done between consecutive frames via a generalized particle filter to detect the vehicle and pair the headlights using the connected component analysis. So, vehicle counting was performed based on the pairing result, with Centroid of each blob we calculated distance between two frames by simple formula and hence dividing it by the time between two frames obtained from the video. Our proposed method was tested on several video surveillance records in different conditions such as dusty or foggy weather, vibrating camera, and in roads with medium-level traffic volumes. The results showed that the new proposed method performed better than our previously published method and other methods, including the Kalman filter or Gaussian model, in different traffic conditions.

INNOVATIVE APPROACHES TO IMPROVE THE TMDL PROCESS: USING ALTERNATIVE WATERSHED SAMPLING DESIGNS TO MEASURE AND CLASSIFY EXPOSURE TO NATURAL AND ANTHROPOGENIC DETERMINANTS OF ECOLOGICAL CONDITION.

EPA Science Inventory

As a means to protect the Nation's rivers and streams, states have adopted biocriteria, a narrative or numeric standard for the biological condition of streams. When stream segments or whole watersheds do not meet a state's biocriteria, then that water body is considered impaired...

Role of microRNAs involved in plant response to nitrogen and phosphorous limiting conditions

PubMed Central

Nguyen, Giao N.; Rothstein, Steven J.; Spangenberg, German; Kant, Surya

2015-01-01

Plant microRNAs (miRNAs) are a class of small non-coding RNAs which target and regulate the expression of genes involved in several growth, development, and metabolism processes. Recent researches have shown involvement of miRNAs in the regulation of uptake and utilization of nitrogen (N) and phosphorus (P) and more importantly for plant adaptation to N and P limitation conditions by modifications in plant growth, phenology, and architecture and production of secondary metabolites. Developing strategies that allow for the higher efficiency of using both N and P fertilizers in crop production is important for economic and environmental benefits. Improved crop varieties with better adaptation to N and P limiting conditions could be a key approach to achieve this effectively. Furthermore, understanding on the interactions between N and P uptake and use and their regulation is important for the maintenance of nutrient homeostasis in plants. This review describes the possible functions of different miRNAs and their cross-talk relevant to the plant adaptive responses to N and P limiting conditions. In addition, a comprehensive understanding of these processes at molecular level and importance of biological adaptation for improved N and P use efficiency is discussed. PMID:26322069

Optimization of 18 F-syntheses using 19 F-reagents at tracer-level concentrations and liquid chromatography/tandem mass spectrometry analysis: Improved synthesis of [18 F]MDL100907.

PubMed

Zhang, Xiang; Dunlow, Ryan; Blackman, Burchelle N; Swenson, Rolf E

2018-05-15

Traditional radiosynthetic optimization faces the challenges of high radiation exposure, cost, and inability to perform serial reactions due to tracer decay. To accelerate tracer development, we have developed a strategy to simulate radioactive 18 F-syntheses by using tracer-level (nanomolar) non-radioactive 19 F-reagents and LC-MS/MS analysis. The methodology was validated with fallypride synthesis under tracer-level 19 F-conditions, which showed reproducible and comparable results with radiosynthesis, and proved the feasibility of this process. Using this approach, the synthesis of [ 18 F]MDL100907 was optimized under 19 F-conditions with greatly improved yield. The best conditions were successfully transferred to radiosynthesis. A radiochemical yield of 19% to 22% was achieved with the radiochemical purity >99% and the molar activity 38.8 to 53.6 GBq/ μmol (n = 3). The tracer-level 19 F-approach provides a high-throughput and cost-effective process to optimize radiosynthesis with reduced radiation exposure. This new method allows medicinal and synthetic chemists to optimize radiolabeling conditions without the need to use radioactivity. Copyright © 2018 John Wiley & Sons, Ltd.

Role of microRNAs involved in plant response to nitrogen and phosphorous limiting conditions.

PubMed

Nguyen, Giao N; Rothstein, Steven J; Spangenberg, German; Kant, Surya

2015-01-01

Plant microRNAs (miRNAs) are a class of small non-coding RNAs which target and regulate the expression of genes involved in several growth, development, and metabolism processes. Recent researches have shown involvement of miRNAs in the regulation of uptake and utilization of nitrogen (N) and phosphorus (P) and more importantly for plant adaptation to N and P limitation conditions by modifications in plant growth, phenology, and architecture and production of secondary metabolites. Developing strategies that allow for the higher efficiency of using both N and P fertilizers in crop production is important for economic and environmental benefits. Improved crop varieties with better adaptation to N and P limiting conditions could be a key approach to achieve this effectively. Furthermore, understanding on the interactions between N and P uptake and use and their regulation is important for the maintenance of nutrient homeostasis in plants. This review describes the possible functions of different miRNAs and their cross-talk relevant to the plant adaptive responses to N and P limiting conditions. In addition, a comprehensive understanding of these processes at molecular level and importance of biological adaptation for improved N and P use efficiency is discussed.

Ergonomics, quality and continuous improvement--conceptual and empirical relationships in an industrial context.

PubMed

Eklund, J

1997-10-01

This paper reviews the literature comparing the fields of ergonomics and quality, mainly in an industrial context, including mutual influences, similarities and differences. Relationships between ergonomics and the factors: work conditions, product design, ISO 9000, continuous improvements and TQM are reviewed in relation to the consequence, application, and process domains. The definitions of ergonomics and quality overlap substantially. Quality deficiencies, human errors and ergonomics problems often have the same cause, which in many cases can be traced to the design of work, workplace and environment e.g. noise, light, postures, loads, pace and work content. In addition, the possibility of performing to a high standard at work is an important prerequisite for satisfaction and well-being. Contradictions between the two fields have been identified in the view of concepts such as standardization, reduction of variability and copying of best practice, requiring further research. The field of quality would gain by incorporating ergonomics knowledge, especially in the areas of work design and human capability, since these factors are decisive for human performance and also therefore the performance of the systems involved. The field of ergonomics, on the other hand, would benefit from developing a stronger emphasis on methodologies and structures for improvement processes, including a clearer link with leadership and company strategies. Just as important is a further development of practicable participative ergonomics methods and tools for use at workplaces by the workers themselves, in order to integrate the top-down and the bottom-up processes and achieve better impact. Using participative processes for problem-solving and continuous improvement, focusing ergonomics and quality jointly has a great potential for improving working conditions and quality results simultaneously, and satisfying most of the interested parties.

The Effects of Aerobic Exercise and Gaming on Cognitive Performance.

PubMed

Douris, Peter C; Handrakis, John P; Apergis, Demitra; Mangus, Robert B; Patel, Rima; Limtao, Jessica; Platonova, Svetlana; Gregorio, Aladino; Luty, Elliot

2018-03-01

The purpose of our study was to investigate the effects of video gaming, aerobic exercise (biking), and the combination of these two activities on the domains of cognitive performance: selective attention, processing speed, and executive functioning. The study was a randomized clinical trial with 40 subjects (mean age 23.7 ± 1.8 years) randomized to one of four thirty-minute conditions: video gaming, biking, simultaneous gaming and biking, and a control condition. Cognitive performance was measured pre and post condition using the Stroop test and Trails B test. A mixed design was utilized. While video gaming, biking, simultaneous gaming and biking conditions improved selective attention and processing speed (p < 0.05), only the bike condition improved the highest order of cognitive performance, executive function (p < 0.01). There were no changes in cognitive performance for the control condition. Previous studies have shown that if tasks approach the limits of attentional capacity there is an increase in the overall chance for errors, known as the dual-task deficit. Simultaneous biking and gaming may have surpassed attentional capacity limits, ultimately increasing errors during the executive function tests of our cognitive performance battery. The results suggest that the fatiguing effects of a combined physically and mentally challenging task that extends after the exercise cessation may overcome the eventual beneficial cognitive effects derived from the physical exercise.

Limits of acceptable change and natural resources planning: when is LAC useful, when is it not?

Treesearch

David N. Cole; Stephen F. McCool

1997-01-01

There are ways to improve the LAC process and its implementational procedures. One significant procedural modification is the addition of a new step. This step — which becomes the first step in the process — involves more explicitly defining goals and desired conditions. For other steps in the process, clarifications of concept and terminology are advanced, as are...

Computational modeling of soot nucleation

NASA Astrophysics Data System (ADS)

Chung, Seung-Hyun

Recent studies indicate that soot is the second most significant driver of climate change---behind CO2, but ahead of methane---and increased levels of soot particles in the air are linked to health hazards such as heart disease and lung cancer. Within the soot formation process, soot nucleation is the least understood step, and current experimental findings are still limited. This thesis presents computational modeling studies of the major pathways of the soot nucleation process. In this study, two regimes of soot nucleation---chemical growth and physical agglomeration---were evaluated and the results demonstrated that combustion conditions determine the relative importance of these two routes. Also, the dimerization process of polycyclic aromatic hydrocarbons, which has been regarded as one of the most important physical agglomeration processes in soot formation, was carefully examined with a new method for obtaining the nucleation rate using molecular dynamics simulation. The results indicate that the role of pyrene dimerization, which is the commonly accepted model, is expected to be highly dependent on various flame temperature conditions and may not be a key step in the soot nucleation process. An additional pathway, coronene dimerization in this case, needed to be included to improve the match with experimental data. The results of this thesis provide insight on the soot nucleation process and can be utilized to improve current soot formation models.

Suppressing flashes of items surrounding targets during calibration of a P300-based brain-computer interface improves performance

NASA Astrophysics Data System (ADS)

Frye, G. E.; Hauser, C. K.; Townsend, G.; Sellers, E. W.

2011-04-01

Since the introduction of the P300 brain-computer interface (BCI) speller by Farwell and Donchin in 1988, the speed and accuracy of the system has been significantly improved. Larger electrode montages and various signal processing techniques are responsible for most of the improvement in performance. New presentation paradigms have also led to improvements in bit rate and accuracy (e.g. Townsend et al (2010 Clin. Neurophysiol. 121 1109-20)). In particular, the checkerboard paradigm for online P300 BCI-based spelling performs well, has started to document what makes for a successful paradigm, and is a good platform for further experimentation. The current paper further examines the checkerboard paradigm by suppressing items which surround the target from flashing during calibration (i.e. the suppression condition). In the online feedback mode the standard checkerboard paradigm is used with a stepwise linear discriminant classifier derived from the suppression condition and one classifier derived from the standard checkerboard condition, counter-balanced. The results of this research demonstrate that using suppression during calibration produces significantly more character selections/min ((6.46) time between selections included) than the standard checkerboard condition (5.55), and significantly fewer target flashes are needed per selection in the SUP condition (5.28) as compared to the RCP condition (6.17). Moreover, accuracy in the SUP and RCP conditions remained equivalent (~90%). Mean theoretical bit rate was 53.62 bits/min in the suppression condition and 46.36 bits/min in the standard checkerboard condition (ns). Waveform morphology also showed significant differences in amplitude and latency.

Permanganate/bisulfite (PM/BS) conditioning-horizontal electro-dewatering (HED) of activated sludge: Effect of reactive Mn(III) species.

PubMed

Guo, Xinxin; Wang, Yili; Wang, Dongsheng

2017-11-01

A novel activated sludge (AS) conditioning method through permanganate/bisulfate (PM/BS) process was proposed. The method involved a new conditioner of reactive Mn(III) intermediate. Moreover, a Mn(III) conditioning-horizontal electro-dewatering (Mn(III) C-HED) process was established to improve AS dewatering performance. Underlying mechanisms were unraveled by investigating changes in physicochemical characteristics, scanning electron microscope (SEM) morphology, and transformation of water and organic matters. The optimum dewatering conditions for Mn(III) C-HED process with the final water content of 86.94% were determined as the combination of KMnO 4 0.01 mol/L AS and NaHSO 3 0.05 mol/L AS at 20 V for 120 min. Results showed that Mn(III) C-HED process effectively reduced free water and bound water with the corresponding removal ratios of 51.68% and 87.62% at the anode-side as well as 36.55% and 85.08% at the cathode-side, respectively. During the PM/BS process, the produced Mn(III), Mn 2+ , and MnO 2 exerted chemical and physical effects on AS conditioning and dewatering. Mn(III) disintegrated extracellular polymeric substances (EPS) fractions and cells in AS, as well as induced partial bound water release. Additionally, flocculation effect induced by Mn 2+ and MnO 2 skeleton building also benefited AS dewatering. AS cells were further disrupted under the effect of a horizontal electric field. Accordingly, EPS within the AS matrix was solubilized, tightly bound (TB)-EPS or loosely bound (LB)-EPS was converted to their corresponding outer EPS fractions, and AS dewaterability improved. Additionally, changes in pH and temperature at HED stage damaged the AS cells and changed the floc properties, thereby leading to easy separation of liquid and AS particles. Copyright © 2017 Elsevier Ltd. All rights reserved.

Methods for improving the damage performance of fused silica polished by magnetorheological finishing

DOE PAGES

Kafka, Kyle R. P.; Hoffman, Brittany N.; Papernov, Semyon; ...

2017-12-11

The laser-induced damage threshold of fused-silica samples processed via magnetorheological finishing is investigated for polishing compounds depending on the type of abrasive material and the post-polishing surface roughness. The effectiveness of laser conditioning is examined using a ramped pre-exposure with the same 351-nm, 3-ns Gaussian pulses. Lastly, we examine chemical etching of the surface and correlate the resulting damage threshold to the etching protocol. A combination of etching and laser conditioning is found to improve the damage threshold by a factor of ~3, while maintaining <1-nm surface roughness.

Methods for improving the damage performance of fused silica polished by magnetorheological finishing

NASA Astrophysics Data System (ADS)

Kafka, K. R. P.; Hoffman, B.; Papernov, S.; DeMarco, M. A.; Hall, C.; Marshall, K. L.; Demos, S. G.

2017-12-01

The laser-induced damage threshold of fused-silica samples processed via magnetorheological finishing is investigated for polishing compounds depending on the type of abrasive material and the post-polishing surface roughness. The effectiveness of laser conditioning is examined using a ramped pre-exposure with the same 351-nm, 3-ns Gaussian pulses. Finally, we examine chemical etching of the surface and correlate the resulting damage threshold to the etching protocol. A combination of etching and laser conditioning is found to improve the damage threshold by a factor of 3, while maintaining <1-nm surface roughness.

Modeling Perceptual Decision Processes

DTIC Science & Technology

2014-09-17

Ratcliff, & Wagenmakers, in press). Previous research suggests that playing action video games improves performance on sensory, perceptual, and...estimate the contribution of several underlying psychological processes. Their analysis indicated that playing action video games leads to faster...third condition in which no video games were played at all. Behavioral data and diffusion model parameters showed similar practice effects for the

A Model for Long Range Planning for Seminole Community College.

ERIC Educational Resources Information Center

Miner, Norris

A model for long-range planning designed to maximize involvement of college personnel, to improve communication among various areas of the college, to provide a process for evaluation of long-range plans and the planning process, to adjust to changing conditions, to utilize data developed at a level useful for actual operations, and to have…

Linking Implementation Process to Intervention Outcomes in a Middle School Obesity Prevention Curriculum, "Choice, Control and Change"

ERIC Educational Resources Information Center

Gray, Heewon Lee; Contento, Isobel R.; Koch, Pamela A.

2015-01-01

This study investigates the link between process evaluation components and the outcomes of a school-based nutrition curriculum intervention, "Choice, Control and Change". Ten New York City public middle schools were recruited and randomly assigned into intervention or control condition. The curriculum was to improve sixth to seventh…

Challenges of Teaching Computer Science in Transition Countries: Albanian University Case

ERIC Educational Resources Information Center

Sotirofski, Kseanela; Kukeli, Agim; Kalemi, Edlira

2010-01-01

The main objective of our study is to determine the challenges faced during the process of teaching Computer Science in a university of a country in transition and make suggestions to improve this teaching process by perfecting the necessary conditions. Our survey builds on the thesis that we live in an information age; information technology is…

Flue gas conditioning for improved particle collection in electrostatic precipitators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Durham, M.D.

1992-04-27

The purpose of this research program is to identify and evaluate a variety of additives capable of increasing particle cohesion which could be used for improving collection efficiency in an ESP. A three-phase screening process will be used to provide the, evaluation of many additives in a logical and cost-effective manner. The three step approach involves the following experimental setups: 1. Provide a preliminary screening in the laboratory by measuring the effects of various conditioning agents on reentrainment of flyash particles in an electric field operating at simulated flue gas conditions. 2. Evaluate the successful additives using a 100 acfmmore » bench-scale ESP operating on actual flue gas. 3. Obtain the data required for scaling up the technology by testing the two or three most promising conditioning agents at the pilot scale.« less

Semantic and self-referential processing of positive and negative trait adjectives in older adults

PubMed Central

Glisky, Elizabeth L.; Marquine, Maria J.

2008-01-01

The beneficial effects of self-referential processing on memory have been demonstrated in numerous experiments with younger adults but have rarely been studied in older individuals. In the present study we tested young people, younger-older adults, and older-older adults in a self-reference paradigm, and compared self-referential processing to general semantic processing. Findings indicated that older adults over the age of 75 and those with below average episodic memory function showed a decreased benefit from both semantic and self-referential processing relative to a structural baseline condition. However, these effects appeared to be confined to the shared semantic processes for the two conditions, leaving the added advantage for self-referential processing unaffected These results suggest that reference to the self engages qualitatively different processes compared to general semantic processing. These processes seem relatively impervious to age and to declining memory and executive function, suggesting that they might provide a particularly useful way for older adults to improve their memories. PMID:18608973

Auditory priming improves neural synchronization in auditory-motor entrainment.

PubMed

Crasta, Jewel E; Thaut, Michael H; Anderson, Charles W; Davies, Patricia L; Gavin, William J

2018-05-22

Neurophysiological research has shown that auditory and motor systems interact during movement to rhythmic auditory stimuli through a process called entrainment. This study explores the neural oscillations underlying auditory-motor entrainment using electroencephalography. Forty young adults were randomly assigned to one of two control conditions, an auditory-only condition or a motor-only condition, prior to a rhythmic auditory-motor synchronization condition (referred to as combined condition). Participants assigned to the auditory-only condition auditory-first group) listened to 400 trials of auditory stimuli presented every 800 ms, while those in the motor-only condition (motor-first group) were asked to tap rhythmically every 800 ms without any external stimuli. Following their control condition, all participants completed an auditory-motor combined condition that required tapping along with auditory stimuli every 800 ms. As expected, the neural processes for the combined condition for each group were different compared to their respective control condition. Time-frequency analysis of total power at an electrode site on the left central scalp (C3) indicated that the neural oscillations elicited by auditory stimuli, especially in the beta and gamma range, drove the auditory-motor entrainment. For the combined condition, the auditory-first group had significantly lower evoked power for a region of interest representing sensorimotor processing (4-20 Hz) and less total power in a region associated with anticipation and predictive timing (13-16 Hz) than the motor-first group. Thus, the auditory-only condition served as a priming facilitator of the neural processes in the combined condition, more so than the motor-only condition. Results suggest that even brief periods of rhythmic training of the auditory system leads to neural efficiency facilitating the motor system during the process of entrainment. These findings have implications for interventions using rhythmic auditory stimulation. Copyright © 2018 Elsevier Ltd. All rights reserved.

19 CFR 10.530 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... other processing of those parts as necessary for improvement to sound working condition by one or more... such a new good; (p) Self-produced material. “Self-produced material” means a good, such as a part or...

Evaluation of Process Performance for Sustainable Hard Machining

NASA Astrophysics Data System (ADS)

Rotella, Giovanna; Umbrello, Domenico; , Oscar W. Dillon, Jr.; Jawahir, I. S.

This paper aims to evaluate the sustainability performance of machining operation of through-hardening steel, AISI 52100, taking into account the impact of the material removal process in its various aspects. Experiments were performed for dry and cryogenic cutting conditions using chamfered cubic boron nitride (CBN) tool inserts at varying cutting conditions (cutting speed and feed rate). Cutting forces, mechanical power, tool wear, white layer thickness, surface roughness and residual stresses were investigated in order to evaluate the effects of extreme in-process cooling on the machined surface. The results indicate that cryogenic cooling has the potential to be used for surface integrity enhancement for improved product life and more sustainable functional performance.

Process Evaluation of the Project SHINE Intervention for African American Families: An Integrated Positive Parenting and Peer Monitoring Approach to Health Promotion.

PubMed

St George, Sara M; Wilson, Dawn K; McDaniel, Tyler; Alia, Kassandra A

2016-07-01

This study describes the process evaluation of Project SHINE, a randomized family-based health promotion intervention that integrated parenting and peer monitoring for improving sedentary behavior, physical activity, and diet in African American families. Adolescent-parent dyads (n = 89) were randomized to a 6-week behavioral, positive parenting, and peer monitoring skills intervention or a general health education comparison condition. Process evaluation included observational ratings of fidelity, attendance records, psychosocial measures, and qualitative interviews. Results indicated that the intervention was delivered with high fidelity based on facilitator adherence (>98% of content delivered) and competent use of theoretically based behavior change and positive parenting skills (100% of ratings >3 on a 1-4 scale). Although only 43% of peers attended the "bring a friend" session, overall attendance was high (4.39 ± 1.51 sessions) as was the retention rate (88%). Parents in the intervention condition reported significant improvements in communication related to adolescents' engagement in health behaviors both on their own and with peers. These findings were supported by qualitative themes related to improvements in family communication and connectedness. This study provides an innovative example of how future family-based health promotion trials can expand their process evaluation approaches by assessing theoretically relevant positive parenting variables as part of ongoing monitoring. © 2016 Society for Public Health Education.

Adaptive memory: the survival scenario enhances item-specific processing relative to a moving scenario.

PubMed

Burns, Daniel J; Hart, Joshua; Griffith, Samantha E; Burns, Amy D

2013-01-01

Nairne, Thompson, and Pandeirada (2007) found that retention of words rated for their relevance to survival is superior to that of words encoded under numerous other deep processing conditions. They suggested that our memory systems might have evolved to confer an advantage for survival-relevant information. Burns, Burns, and Hwang (2011) suggested a two-process explanation of the proximate mechanisms responsible for the survival advantage. Whereas most control tasks encourage only one type of processing, the survival task encourages both item-specific and relational processing. They found that when control tasks encouraged both types of processing, the survival processing advantage was eliminated. However, none of their control conditions included non-survival scenarios (e.g., moving, vacation, etc.), so it is not clear how this two-process explanation would explain the survival advantage when scenarios are used as control conditions. The present experiments replicated the finding that the survival scenario improves recall relative to a moving scenario in both a between-lists and within-list design and also provided evidence that this difference was accompanied by an item-specific processing difference, not a difference in relational processing. The implications of these results for several existing accounts of the survival processing effect are discussed.

Consequences of atomic layer etching on wafer scale uniformity in inductively coupled plasmas

NASA Astrophysics Data System (ADS)

Huard, Chad M.; Lanham, Steven J.; Kushner, Mark J.

2018-04-01

Atomic layer etching (ALE) typically divides the etching process into two self-limited reactions. One reaction passivates a single layer of material while the second preferentially removes the passivated layer. As such, under ideal conditions the wafer scale uniformity of ALE should be independent of the uniformity of the reactant fluxes onto the wafers, provided all surface reactions are saturated. The passivation and etch steps should individually asymptotically saturate after a characteristic fluence of reactants has been delivered to each site. In this paper, results from a computational investigation are discussed regarding the uniformity of ALE of Si in Cl2 containing inductively coupled plasmas when the reactant fluxes are both non-uniform and non-ideal. In the parameter space investigated for inductively coupled plasmas, the local etch rate for continuous processing was proportional to the ion flux. When operated with saturated conditions (that is, both ALE steps are allowed to self-terminate), the ALE process is less sensitive to non-uniformities in the incoming ion flux than continuous etching. Operating ALE in a sub-saturation regime resulted in less uniform etching. It was also found that ALE processing with saturated steps requires a larger total ion fluence than continuous etching to achieve the same etch depth. This condition may result in increased resist erosion and/or damage to stopping layers using ALE. While these results demonstrate that ALE provides increased etch depth uniformity, they do not show an improved critical dimension uniformity in all cases. These possible limitations to ALE processing, as well as increased processing time, will be part of the process optimization that includes the benefits of atomic resolution and improved uniformity.

The Effects of Digital Noise Reduction on the Acceptance of Background Noise

PubMed Central

Mueller, H. Gustav; Weber, Jennifer; Hornsby, Benjamin W. Y.

2006-01-01

Modern hearing aids commonly employ digital noise reduction (DNR) algorithms. The potential benefit of these algorithms is to provide improved speech understanding in noise or, at the least, to provide relaxed listening or increased ease of listening. In this study, 22 adults were fitted with 16-channel wide-dynamic-range compression hearing aids containing DNR processing. The DNR includes both modulation-based and Wiener-filter-type algorithms working simultaneously. Both speech intelligibility and acceptable noise level (ANL) were assessed using the Hearing in Noise Test (HINT) with DNR on and DNR off. The ANL was also assessed without hearing aids. The results showed a significant mean improvement for the ANL (4.2 dB) for the DNR-on condition when compared to DNR-off condition. Moreover, there was a significant correlation between the magnitude of ANL improvement (relative to DNR on) and the DNR-off ANL. There was no significant mean improvement for the HINT for the DNR-on condition, and on an individual basis, the HINT score did not significantly correlate with either aided ANL (DNR on or DNR off). These findings suggest that at least within the constraints of the DNR algorithms and test conditions employed in this study, DNR can significantly improve the clinically measured ANL, which may result in improved ease of listening for speech-in-noise situations. PMID:16959732

Influence of Dynamic Hydraulic Conditions on Nitrogen Cycling in Column Experiments

NASA Astrophysics Data System (ADS)

Gassen, Niklas; von Netzer, Frederick; Ryabenko, Evgenia; Lüders, Tillmann; Stumpp, Christine

2015-04-01

In order to improve management strategies of agricultural nitrogen input, it is of major importance to further understand which factors influence turnover processes within the nitrogen cycle. Many studies have focused on the fate of nitrate in hydrological systems, but up to date only little is known about the influence of dynamic hydraulic conditions on the fate of nitrate at the soil-groundwater interface. We conducted column experiments with natural sediment and compared a system with a fluctuating water table to systems with different water content and static conditions under the constant input of ammonia into the system. We used hydrochemical methods in order to trace nitrogen species, 15N isotope methods to get information about dominating turnover processes and microbial community analysis in order to connect hydrochemical and microbial information. We found that added ammonia was removed more effectively under dynamic hydraulic conditions than under static conditions. Furthermore, denitrification is the dominant process under saturated, static conditions, while nitrification is more important under unsaturated, static conditions. We conclude that a fluctuating water table creates hot spots where both nitrification and denitrification processes can occur spatially close to each other and therefore remove nitrogen more effectively from the system. Furthermore, the fluctuating water table enhances the exchange of solutes and triggers hot moments of solute turnover. Therefore we conclude that a fluctuating water table can amplify hot spots and trigger hot moments of nitrogen cycling.

Rational thinking in school-based practice.

PubMed

Clark, Mary Kristen; Flynn, Perry

2011-01-01

We reflect on Alan Kamhi's (2011) prologue on balancing certainty and uncertainty as it pertains to school-based practice. In schools, rational thinking depends on effective team processes, much like professional learning communities. We consider the conditions that are required for rational thinking and how rational team dialogue confronts uncertainties. We provide suggestions for how this dialogue can be used throughout the individualized education program (IEP) process to lead to more positive experiences for all team members as well as improved student outcomes. Rational thinking in school-based practice may be manifest by closer adherence to the tenets [corrected] of the Individuals With Disabilities Education Improvement Act of 2004 (IDEIA), ultimately resulting in increased rational thought and improved student outcomes.

Roll-to-Roll Advanced Materials Manufacturing DOE Lab Consortium - FY16 Annual Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel, Claus; Wood, III, David L.; Krumdick, Gregory

2016-12-01

A DOE laboratory consortium comprised of ORNL, ANL, NREL and LBNL, coordinating with Kodak’s Eastman Business Park (Kodak) and other selected industry partners, was formed to address enhancing battery electrode performance and R2R manufacturing challenges. The objective of the FY 2016 seed project was to develop a materials genome synthesis process amenable to R2R manufacturing and to provide modeling, simulation, processing, and manufacturing techniques that demonstrate the feasibility of process controls and scale-up potential for improved battery electrodes. The research efforts were to predict and measure changes and results in electrode morphology and performance based on process condition changes; tomore » evaluate mixed, active, particle size deposition and drying for novel electrode materials; and to model various process condition changes and the resulting morphology and electrode performance.« less

An adaptive confidence limit for periodic non-steady conditions fault detection

NASA Astrophysics Data System (ADS)

Wang, Tianzhen; Wu, Hao; Ni, Mengqi; Zhang, Milu; Dong, Jingjing; Benbouzid, Mohamed El Hachemi; Hu, Xiong

2016-05-01

System monitoring has become a major concern in batch process due to the fact that failure rate in non-steady conditions is much higher than in steady ones. A series of approaches based on PCA have already solved problems such as data dimensionality reduction, multivariable decorrelation, and processing non-changing signal. However, if the data follows non-Gaussian distribution or the variables contain some signal changes, the above approaches are not applicable. To deal with these concerns and to enhance performance in multiperiod data processing, this paper proposes a fault detection method using adaptive confidence limit (ACL) in periodic non-steady conditions. The proposed ACL method achieves four main enhancements: Longitudinal-Standardization could convert non-Gaussian sampling data to Gaussian ones; the multiperiod PCA algorithm could reduce dimensionality, remove correlation, and improve the monitoring accuracy; the adaptive confidence limit could detect faults under non-steady conditions; the fault sections determination procedure could select the appropriate parameter of the adaptive confidence limit. The achieved result analysis clearly shows that the proposed ACL method is superior to other fault detection approaches under periodic non-steady conditions.

Numerical investigation of the effect of friction conditions to increase die life

NASA Astrophysics Data System (ADS)

Mutlu, M. O.; Guleryuz, C. G.; Parlar, Z.

2017-02-01

The standard die materials in aluminium extrusion offer good mechanical properties like high tempering resistance, high strength and ductility. On the other hand, they struggle with the problem of sliding wear. As a result, there is a growing interest in using surface treatment techniques to increase the wear resistance of extrusion dies. In this study, it is aimed to observe the effects of the different friction conditions on material flow and contact pressure in extrusion process. These friction conditions can be obtained with the application of a variety of surface treatment. In this way, it is expected to decrease the friction force on the die bearing area and to increase the homogeneity of the material flow which will result in the increase of the quality of the extrudate as well as the improvement of the process economically by extending die life. For this purpose, an extrusion process is simulated with a finite element software. A die made of 1.2344 hot work tool steel-commonly used die material for aluminium extrusion process- has been modelled and Al 1100 alloy used as billet material. Various friction factor values defined on the die surface under the same process parameters and effects of changing frictional conditions on the die and the extrusion process have been discussed.

The influence of supercritical carbon dioxide (SC-CO2) processing conditions on drug loading and physicochemical properties.

PubMed

Ahern, Robert J; Crean, Abina M; Ryan, Katie B

2012-12-15

Poor water solubility of drugs can complicate their commercialisation because of reduced drug oral bioavailability. Formulation strategies such as increasing the drug surface area are frequently employed in an attempt to increase dissolution rate and hence, improve oral bioavailability. Maximising the drug surface area exposed to the dissolution medium can be achieved by loading drug onto a high surface area carrier like mesoporous silica (SBA-15). The aim of this work was to investigate the impact of altering supercritical carbon dioxide (SC-CO(2)) processing conditions, in an attempt to enhance drug loading onto SBA-15 and increase the drug's dissolution rate. Other formulation variables such as the mass ratio of drug to SBA-15 and the procedure for combining the drug and SBA-15 were also investigated. A model drug with poor water solubility, fenofibrate, was selected for this study. High drug loading efficiencies were obtained using SC-CO(2), which were influenced by the processing conditions employed. Fenofibrate release rate was enhanced greatly after loading onto mesoporous silica. The results highlighted the potential of this SC-CO(2) drug loading approach to improve the oral bioavailability of poorly water soluble drugs. Copyright © 2012 Elsevier B.V. All rights reserved.

Applying Lean to the F-15 Maintenance Process for the Royal Saudi Air Force

DTIC Science & Technology

2014-03-01

Royal Saudi Air Force. The research focuses on improving the F-15 maintenance process in the Royal Saudi Air Force’s Maintenance Squadrons. The F-15...and on the aircraft age condition, the researcher concludes it is time to get rid of some obstacles and use new management techniques to resolve the...processes? Research Focus This research is focusing on the Royal Saudi Air Force F-15 maintenance process. Because of the time and

Beyond Texas City: the state of process safety in the unionized U.S. oil refining industry.

PubMed

McQuiston, Thomas H; Lippin, Tobi Mae; Bradley-Bull, Kristin; Anderson, Joseph; Beach, Josie; Beevers, Gary; Frederick, Randy J; Frederick, James; Greene, Tammy; Hoffman, Thomas; Lefton, James; Nibarger, Kim; Renner, Paul; Ricks, Brian; Seymour, Thomas; Taylor, Ren; Wright, Mike

2009-01-01

The March 2005 British Petroleum (BP) Texas City Refinery disaster provided a stimulus to examine the state of process safety in the U.S. refining industry. Participatory action researchers conducted a nation-wide mail-back survey of United Steelworkers local unions and collected data from 51 unionized refineries. The study examined the prevalence of highly hazardous conditions key to the Texas City disaster, refinery actions to address those conditions, emergency preparedness and response, process safety systems, and worker training. Findings indicate that the key highly hazardous conditions were pervasive and often resulted in incidents or near-misses. Respondents reported worker training was insufficient and less than a third characterized their refineries as very prepared to respond safely to a hazardous materials emergency. The authors conclude that the potential for future disasters plagues the refining industry. In response, they call for effective proactive OSHA regulation and outline ten urgent and critical actions to improve refinery process safety.

Understanding brassinosteroid-regulated mechanisms to improve stress tolerance in plants: a critical review.

PubMed

Nawaz, Fahim; Naeem, Muhammad; Zulfiqar, Bilal; Akram, Asim; Ashraf, Muhammad Yasin; Raheel, Muhammad; Shabbir, Rana Nauman; Hussain, Rai Altaf; Anwar, Irfan; Aurangzaib, Muhammad

2017-07-01

Brassinosteroids (BRs) are steroidal plant hormones involved in regulation of physiological and molecular processes to ameliorate various biotic and abiotic stresses. Exogenous application of BRs to improve stress tolerance in plants has recently become a high research priority. Several studies have revealed the involvement of these steroidal hormones in upregulation of stress-related defense genes and their cross talk with other metabolic pathways. This is likely to stimulate research on many unanswered questions regarding their role in enhancing the ability of plants to tolerate adverse environmental conditions. Thus, this review appraises new insights on mechanisms mediating BR-regulated changes in plants, focused mainly on their involvement in regulation of physiological and molecular mechanisms under stress conditions. Herein, examples of BR-stimulated modulation of antioxidant defense system and upregulation of transcription factors in plants exposed to various biotic (bacterial, viral, and fungal attack) and abiotic stresses (drought, salinity, heat, low temperature, and heavy metal stress) are discussed. Based on these insights, future research in the current direction can be helpful to increase our understanding of BR-mediated complex and interrelated processes under stress conditions.

An end-to-end communications architecture for condition-based maintenance applications

NASA Astrophysics Data System (ADS)

Kroculick, Joseph

2014-06-01

This paper explores challenges in implementing an end-to-end communications architecture for Condition-Based Maintenance Plus (CBM+) data transmission which aligns with the Army's Network Modernization Strategy. The Army's Network Modernization strategy is based on rolling out network capabilities which connect the smallest unit and Soldier level to enterprise systems. CBM+ is a continuous improvement initiative over the life cycle of a weapon system or equipment to improve the reliability and maintenance effectiveness of Department of Defense (DoD) systems. CBM+ depends on the collection, processing and transport of large volumes of data. An important capability that enables CBM+ is an end-to-end network architecture that enables data to be uploaded from the platform at the tactical level to enterprise data analysis tools. To connect end-to-end maintenance processes in the Army's supply chain, a CBM+ network capability can be developed from available network capabilities.

Development of flame resistant treatment for Nomex fibrous structures

NASA Technical Reports Server (NTRS)

Toy, M. S.

1977-01-01

Flame resistant fibrous materials for space shuttle application were developed through chemical modification of commercially available aromatic polyamide fibrous products. The new surface treatment was achieved in the laboratory by ultraviolet activation of the fabric in the presence of fluoroolefin monomers and a diluent gas. The monomers grafted under these conditions provide the improved properties of the fabric in flame resistance, chemical inertness, and nonwettability without the sacrifice of color or physical properties. The laboratory reaction vessel was scaled-up to a batch continuous process, which treats ten yards of the commercial width textiles. The treated commercial width Nomex (HT-10-41) from the scaled-up reactor is self-extinguishing in an oxygen-enriched environment, water-repellent, soft, silky, and improved in chemical resistance. Unlike most textile processes, the grafting unit operates under dry conditions and no chemical by-products have to be washed out of the finished product.

Piezoresistive Cantilever Performance—Part II: Optimization

PubMed Central

Park, Sung-Jin; Doll, Joseph C.; Rastegar, Ali J.; Pruitt, Beth L.

2010-01-01

Piezoresistive silicon cantilevers fabricated by ion implantation are frequently used for force, displacement, and chemical sensors due to their low cost and electronic readout. However, the design of piezoresistive cantilevers is not a straightforward problem due to coupling between the design parameters, constraints, process conditions, and performance. We systematically analyzed the effect of design and process parameters on force resolution and then developed an optimization approach to improve force resolution while satisfying various design constraints using simulation results. The combined simulation and optimization approach is extensible to other doping methods beyond ion implantation in principle. The optimization results were validated by fabricating cantilevers with the optimized conditions and characterizing their performance. The measurement results demonstrate that the analytical model accurately predicts force and displacement resolution, and sensitivity and noise tradeoff in optimal cantilever performance. We also performed a comparison between our optimization technique and existing models and demonstrated eight times improvement in force resolution over simplified models. PMID:20333323

Visualising reacting single atoms under controlled conditions: Advances in atomic resolution in situ Environmental (Scanning) Transmission Electron Microscopy (E(S)TEM)

NASA Astrophysics Data System (ADS)

Boyes, Edward D.; Gai, Pratibha L.

2014-02-01

Advances in atomic resolution Environmental (Scanning) Transmission Electron Microscopy (E(S)TEM) for probing gas-solid catalyst reactions in situ at the atomic level under controlled reaction conditions of gas environment and temperature are described. The recent development of the ESTEM extends the capability of the ETEM by providing the direct visualisation of single atoms and the atomic structure of selected solid state heterogeneous catalysts in their working states in real-time. Atomic resolution E(S)TEM provides a deeper understanding of the dynamic atomic processes at the surface of solids and their mechanisms of operation. The benefits of atomic resolution-E(S)TEM to science and technology include new knowledge leading to improved technological processes with substantial economic benefits, improved healthcare, reductions in energy needs and the management of environmental waste generation. xml:lang="fr"

Conditional self-discrimination enhances dendritic spine number and dendritic length at prefrontal cortex and hippocampal neurons of rats.

PubMed

Penagos-Corzo, Julio C; Bonilla, Andrea; Rodríguez-Moreno, Antonio; Flores, Gonzalo; Negrete-Díaz, José V

2015-11-01

We studied conditional self-discrimination (CSD) in rats and compared the neuronal cytoarchitecture of untrained animals and rats that were trained in self-discrimination. For this purpose, we used thirty 10-week-old male rats were randomized into three groups: one control group and two conditioning groups: a comparison group (associative learning) and an experimental group (self-discrimination). At the end of the conditioning process, the experimental group managed to discriminate their own state of thirst. After the conditioning process, dendritic morphological changes in the pyramidal neurons of the prefrontal cortex and CA1 region of the dorsal hippocampus were evaluated using Golgi-Cox stain method and then analyzed by the Sholl method. Differences were found in total dendritic length and spine density. Animals trained in self-discrimination showed an increase in the dendritic length and the number of dendritic spines of neurons of the prefrontal cortex and CA1 region of the dorsal hippocampus. Our data suggest that conditional self-discrimination improves the connectivity of the prefrontal cortex and dorsal CA1, which has implications for memory and learning processes. © 2015 Wiley Periodicals, Inc.

Improvement of the Mechanical Properties of 1022 Carbon Steel Coil by Using the Taguchi Method to Optimize Spheroidized Annealing Conditions.

PubMed

Yang, Chih-Cheng; Liu, Chang-Lun

2016-08-12

Cold forging is often applied in the fastener industry. Wires in coil form are used as semi-finished products for the production of billets. This process usually requires preliminarily drawing wire coil in order to reduce the diameter of products. The wire usually has to be annealed to improve its cold formability. The quality of spheroidizing annealed wire affects the forming quality of screws. In the fastener industry, most companies use a subcritical process for spheroidized annealing. Various parameters affect the spheroidized annealing quality of steel wire, such as the spheroidized annealing temperature, prolonged heating time, furnace cooling time and flow rate of nitrogen (protective atmosphere). The effects of the spheroidized annealing parameters affect the quality characteristics of steel wire, such as the tensile strength and hardness. A series of experimental tests on AISI 1022 low carbon steel wire are carried out and the Taguchi method is used to obtain optimum spheroidized annealing conditions to improve the mechanical properties of steel wires for cold forming. The results show that the spheroidized annealing temperature and prolonged heating time have the greatest effect on the mechanical properties of steel wires. A comparison between the results obtained using the optimum spheroidizing conditions and the measures using the original settings shows the new spheroidizing parameter settings effectively improve the performance measures over their value at the original settings. The results presented in this paper could be used as a reference for wire manufacturers.

Condition monitoring of turning process using infrared thermography technique - An experimental approach

NASA Astrophysics Data System (ADS)

Prasad, Balla Srinivasa; Prabha, K. Aruna; Kumar, P. V. S. Ganesh

2017-03-01

In metal cutting machining, major factors that affect the cutting tool life are machine tool vibrations, tool tip/chip temperature and surface roughness along with machining parameters like cutting speed, feed rate, depth of cut, tool geometry, etc., so it becomes important for the manufacturing industry to find the suitable levels of process parameters for obtaining maintaining tool life. Heat generation in cutting was always a main topic to be studied in machining. Recent advancement in signal processing and information technology has resulted in the use of multiple sensors for development of the effective monitoring of tool condition monitoring systems with improved accuracy. From a process improvement point of view, it is definitely more advantageous to proactively monitor quality directly in the process instead of the product, so that the consequences of a defective part can be minimized or even eliminated. In the present work, a real time process monitoring method is explored using multiple sensors. It focuses on the development of a test bed for monitoring the tool condition in turning of AISI 316L steel by using both coated and uncoated carbide inserts. Proposed tool condition monitoring (TCM) is evaluated in the high speed turning using multiple sensors such as Laser Doppler vibrometer and infrared thermography technique. The results indicate the feasibility of using the dominant frequency of the vibration signals for the monitoring of high speed turning operations along with temperatures gradient. A possible correlation is identified in both regular and irregular cutting tool wear. While cutting speed and feed rate proved to be influential parameter on the depicted temperatures and depth of cut to be less influential. Generally, it is observed that lower heat and temperatures are generated when coated inserts are employed. It is found that cutting temperatures are gradually increased as edge wear and deformation developed.

Study of sensor spectral responses and data processing algorithms and architectures for onboard feature identification

NASA Technical Reports Server (NTRS)

Huck, F. O.; Davis, R. E.; Fales, C. L.; Aherron, R. M.

1982-01-01

A computational model of the deterministic and stochastic processes involved in remote sensing is used to study spectral feature identification techniques for real-time onboard processing of data acquired with advanced earth-resources sensors. Preliminary results indicate that: Narrow spectral responses are advantageous; signal normalization improves mean-square distance (MSD) classification accuracy but tends to degrade maximum-likelihood (MLH) classification accuracy; and MSD classification of normalized signals performs better than the computationally more complex MLH classification when imaging conditions change appreciably from those conditions during which reference data were acquired. The results also indicate that autonomous categorization of TM signals into vegetation, bare land, water, snow and clouds can be accomplished with adequate reliability for many applications over a reasonably wide range of imaging conditions. However, further analysis is required to develop computationally efficient boundary approximation algorithms for such categorization.

Resist process optimization for further defect reduction

NASA Astrophysics Data System (ADS)

Tanaka, Keiichi; Iseki, Tomohiro; Marumoto, Hiroshi; Takayanagi, Koji; Yoshida, Yuichi; Uemura, Ryouichi; Yoshihara, Kosuke

2012-03-01

Defect reduction has become one of the most important technical challenges in device mass-production. Knowing that resist processing on a clean track strongly impacts defect formation in many cases, we have been trying to improve the track process to enhance customer yield. For example, residual type defect and pattern collapse are strongly related to process parameters in developer, and we have reported new develop and rinse methods in the previous papers. Also, we have reported the optimization method of filtration condition to reduce bridge type defects, which are mainly caused by foreign substances such as gels in resist. Even though we have contributed resist caused defect reduction in past studies, defect reduction requirements continue to be very important. In this paper, we will introduce further process improvements in terms of resist defect reduction, including the latest experimental data.

Independent practice associations and physician-hospital organizations can improve care management for smaller practices.

PubMed

Casalino, Lawrence P; Wu, Frances M; Ryan, Andrew M; Copeland, Kennon; Rittenhouse, Diane R; Ramsay, Patricia P; Shortell, Stephen M

2013-08-01

Pay-for-performance, public reporting, and accountable care organization programs place pressures on physicians to use health information technology and organized care management processes to improve the care they provide. But physician practices that are not large may lack the resources and size to implement such processes. We used data from a unique national survey of 1,164 practices with fewer than twenty physicians to provide the first information available on the extent to which independent practice associations (IPAs) and physician-hospital organizations (PHOs) might make it possible for these smaller practices to share resources to improve care. Nearly a quarter of the practices participated in an IPA or a PHO that accounted for a significant proportion of their patients. On average, practices participating in these organizations provided nearly three times as many care management processes for patients with chronic conditions as nonparticipating practices did (10.4 versus 3.8). Half of these processes were provided only by IPAs or PHOs. These organizations may provide a way for small and medium-size practices to systematically improve care and participate in accountable care organizations.

Processing of micro-nano bacterial cellulose with hydrolysis method as a reinforcing bioplastic

NASA Astrophysics Data System (ADS)

Maryam, Maryam; Dedy, Rahmad; Yunizurwan, Yunizurwan

2017-01-01

Nanotechnology is the ability to create and manipulate atoms and molecules on the smallest of scales. Their size allows them to exhibit novel and significantly improved physical, chemical, biological properties, phenomena, and processes because of their size. The purpose of this research is obtaining micro-nano bacterial cellulose as reinforcing bioplastics. Bacterial cellulose (BC) was made from coconut water for two weeks. BC was dried and grinded. Bacterial cellulose was given purification process with NaOH 5% for 6 hours. Making the micro-nano bacterial cellulose with hydrolysis method. Hydrolysis process with hydrochloric acid (HCl) at the conditions 3,5M, 55°C, 6 hours. Drying process used spray dryer. The hydrolysis process was obtained bacterial cellulose with ±7 μm. The addition 2% micro-nano bacterial cellulose as reinforcing in bioplastics composite can improve the physical characteristics.

Collaborative Technology Assessments Of Transient Field Processing And Additive Manufacturing Technologies As Applied To Gas Turbine Components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ludtka, Gerard Michael; Dehoff, Ryan R.; Szabo, Attila

2016-01-01

ORNL partnered with GE Power & Water to investigate the effect of thermomagnetic processing on the microstructure and mechanical properties of GE Power & Water newly developed wrought Ni-Fe-Cr alloys. Exploration of the effects of high magnetic field process during heat treatment of the alloys indicated conditions where applications of magnetic fields yields significant property improvements. The alloy aged using high magnetic field processing exhibited 3 HRC higher hardness compared to the conventionally-aged alloy. The alloy annealed at 1785 F using high magnetic field processing demonstrated an average creep life 2.5 times longer than that of the conventionally heat-treated alloy.more » Preliminary results show that high magnetic field processing can improve the mechanical properties of Ni-Fe-Cr alloys and potentially extend the life cycle of the gas turbine components such as nozzles leading to significant energy savings.« less

Kilogram-scale prexasertib monolactate monohydrate synthesis under continuous-flow CGMP conditions.

PubMed

Cole, Kevin P; Groh, Jennifer McClary; Johnson, Martin D; Burcham, Christopher L; Campbell, Bradley M; Diseroad, William D; Heller, Michael R; Howell, John R; Kallman, Neil J; Koenig, Thomas M; May, Scott A; Miller, Richard D; Mitchell, David; Myers, David P; Myers, Steven S; Phillips, Joseph L; Polster, Christopher S; White, Timothy D; Cashman, Jim; Hurley, Declan; Moylan, Robert; Sheehan, Paul; Spencer, Richard D; Desmond, Kenneth; Desmond, Paul; Gowran, Olivia

2017-06-16

Advances in drug potency and tailored therapeutics are promoting pharmaceutical manufacturing to transition from a traditional batch paradigm to more flexible continuous processing. Here we report the development of a multistep continuous-flow CGMP (current good manufacturing practices) process that produced 24 kilograms of prexasertib monolactate monohydrate suitable for use in human clinical trials. Eight continuous unit operations were conducted to produce the target at roughly 3 kilograms per day using small continuous reactors, extractors, evaporators, crystallizers, and filters in laboratory fume hoods. Success was enabled by advances in chemistry, engineering, analytical science, process modeling, and equipment design. Substantial technical and business drivers were identified, which merited the continuous process. The continuous process afforded improved performance and safety relative to batch processes and also improved containment of a highly potent compound. Copyright © 2017, American Association for the Advancement of Science.

Changes in Wood Processing and Use Have Influenced the Likelihood of Beetle Infestations in Seasoned Wood

Treesearch

Lonnie H. Williams

1980-01-01

Fewer houses are being built with crawl spaces and more houses have central heating and air-conditioning, so the number of anobiid beetle infestations should decline. The likelihood of lyctid infestations in domestic hardwoods has been decreased by improved processing and marketing, but increased imports of tropical hardwoods likely will increase the frequency of...

Hydropyrolysis process

DOEpatents

Ullman, Alan Z.; Silverman, Jacob; Friedman, Joseph

1986-01-01

An improved process for producing a methane-enriched gas wherein a hydrogen-deficient carbonaceous material is treated with a hydrogen-containing pyrolysis gas at an elevated temperature and pressure to produce a product gas mixture including methane, carbon monoxide and hydrogen. The improvement comprises passing the product gas mixture sequentially through a water-gas shift reaction zone and a gas separation zone to provide separate gas streams of methane and of a recycle gas comprising hydrogen, carbon monoxide and methane for recycle to the process. A controlled amount of steam also is provided which when combined with the recycle gas provides a pyrolysis gas for treatment of additional hydrogen-deficient carbonaceous material. The amount of steam used and the conditions within the water-gas shift reaction zone and gas separation zone are controlled to obtain a steady-state composition of pyrolysis gas which will comprise hydrogen as the principal constituent and a minor amount of carbon monoxide, steam and methane so that no external source of hydrogen is needed to supply the hydrogen requirements of the process. In accordance with a particularly preferred embodiment, conditions are controlled such that there also is produced a significant quantity of benzene as a valuable coproduct.

Levels-of-processing effects on a task of olfactory naming.

PubMed

Royet, Jean-Pierre; Koenig, Olivier; Paugam-Moisy, Helene; Puzenat, Didier; Chasse, Jean-Luc

2004-02-01

The effects of odor processing were investigated at various analytical levels, from simple sensory analysis to deep or semantic analysis, on a subsequent task of odor naming. Students (106 women, 23.6 +/- 5.5 yr. old; 65 men, 25.1 +/- 7.1 yr. old) were tested. The experimental procedure included two successive sessions, a first session to characterize a set of 30 odors with criteria that used various depths of processing and a second session to name the odors as quickly as possible. Four processing conditions rated the odors using descriptors before naming the odor. The control condition did not rate the odors before naming. The processing conditions were based on lower-level olfactory judgments (superficial processing), higher-level olfactory-gustatory-somesthetic judgments (deep processing), and higher-level nonolfactory judgments (Deep-Control processing, with subjects rating odors with auditory and visual descriptors). One experimental condition successively grouped lower- and higher-level olfactory judgments (Superficial-Deep processing). A naming index which depended on response accuracy and the subjects' response time were calculated. Odor naming was modified for 18 out of 30 odorants as a function of the level of processing required. For 94.5% of significant variations, the scores for odor naming were higher following those tasks for which it was hypothesized that the necessary olfactory processing was carried out at a deeper level. Performance in the naming task was progressively improved as follows: no rating of odors, then superficial, deep-control, deep, and superficial-deep processings. These data show that the deepest olfactory encoding was later associated with progressively higher performance in naming.

Improved fluorescent labeling of chitin oligomers: Chitinolytic properties of acidic mammalian chitinase under somatic tissue pH conditions.

PubMed

Wakita, Satoshi; Kimura, Masahiro; Kato, Naoki; Kashimura, Akinori; Kobayashi, Shunsuke; Kanayama, Naoto; Ohno, Misa; Honda, Shotaro; Sakaguchi, Masayoshi; Sugahara, Yasusato; Bauer, Peter O; Oyama, Fumitaka

2017-05-15

Acidic mammalian chitinase (AMCase) has been implicated in various pathophysiological conditions including asthma, allergic inflammation and food processing. AMCase is most active at pH 2.0, and its activity gradually decreases to up to pH 8. Here we analyzed chitin degradation by AMCase in weak acidic to neutral conditions by fluorophore-assisted carbohydrate electrophoresis established originally for oligosaccharides analysis. We found that specific fragments with slower-than-expected mobility as defined by chitin oligosaccharide markers were generated at pH 5.0∼8.0 as by-products of the reaction. We established an improved method for chitin oligosaccharides suppressing this side reaction by pre-acidification of the fluorophore-labeling reaction mixture. Our improved method specifically detects chitin oligosaccharides and warrants quantification of up to 50nmol of the material. Using this strategy, we found that AMCase produced dimer of N-acetyl-d-glucosamine (GlcNAc) at strong acidic to neutral condition. Moreover, we found that AMCase generates (GlcNAc) 2 as well as (GlcNAc) 3 under physiological conditions. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

The application of reduced-processing decision support systems to facilitate the acquisition of decision-making skills.

PubMed

Perry, Nathan C; Wiggins, Mark W; Childs, Merilyn; Fogarty, Gerard

2013-06-01

The study was designed to examine whether the availability of reduced-processing decision support system interfaces could improve the decision making of inexperienced personnel in the context of Although research into reduced-processing decision support systems has demonstrated benefits in minimizing cognitive load, these benefits have not typically translated into direct improvements in decision accuracy because of the tendency for inexperienced personnel to focus on less-critical information. The authors investigated whether reduced-processing interfaces that direct users' attention toward the most critical cues for decision making can produce improvements in decision-making performance. Novice participants made incident command-related decisions in experimental conditions that differed according to the amount of information that was available within the interface, the level of control that they could exert over the presentation of information, and whether they had received decision training. The results revealed that despite receiving training, participants improved in decision accuracy only when they were provided with an interface that restricted information access to the most critical cues. It was concluded that an interface that restricts information access to only the most critical cues in the scenario can facilitate improvements in decision performance. Decision support system interfaces that encourage the processing of the most critical cues have the potential to improve the accuracy and timeliness of decisions made by inexperienced personnel.

Improved signal processing approaches in an offline simulation of a hybrid brain–computer interface

PubMed Central

Brunner, Clemens; Allison, Brendan Z.; Krusienski, Dean J.; Kaiser, Vera; Müller-Putz, Gernot R.; Pfurtscheller, Gert; Neuper, Christa

2012-01-01

In a conventional brain–computer interface (BCI) system, users perform mental tasks that yield specific patterns of brain activity. A pattern recognition system determines which brain activity pattern a user is producing and thereby infers the user’s mental task, allowing users to send messages or commands through brain activity alone. Unfortunately, despite extensive research to improve classification accuracy, BCIs almost always exhibit errors, which are sometimes so severe that effective communication is impossible. We recently introduced a new idea to improve accuracy, especially for users with poor performance. In an offline simulation of a “hybrid” BCI, subjects performed two mental tasks independently and then simultaneously. This hybrid BCI could use two different types of brain signals common in BCIs – event-related desynchronization (ERD) and steady-state evoked potentials (SSEPs). This study suggested that such a hybrid BCI is feasible. Here, we re-analyzed the data from our initial study. We explored eight different signal processing methods that aimed to improve classification and further assess both the causes and the extent of the benefits of the hybrid condition. Most analyses showed that the improved methods described here yielded a statistically significant improvement over our initial study. Some of these improvements could be relevant to conventional BCIs as well. Moreover, the number of illiterates could be reduced with the hybrid condition. Results are also discussed in terms of dual task interference and relevance to protocol design in hybrid BCIs. PMID:20153371

Visual training improves perceptual grouping based on basic stimulus features.

PubMed

Kurylo, Daniel D; Waxman, Richard; Kidron, Rachel; Silverstein, Steven M

2017-10-01

Training on visual tasks improves performance on basic and higher order visual capacities. Such improvement has been linked to changes in connectivity among mediating neurons. We investigated whether training effects occur for perceptual grouping. It was hypothesized that repeated engagement of integration mechanisms would enhance grouping processes. Thirty-six participants underwent 15 sessions of training on a visual discrimination task that required perceptual grouping. Participants viewed 20 × 20 arrays of dots or Gabor patches and indicated whether the array appeared grouped as vertical or horizontal lines. Across trials stimuli became progressively disorganized, contingent upon successful discrimination. Four visual dimensions were examined, in which grouping was based on similarity in luminance, color, orientation, and motion. Psychophysical thresholds of grouping were assessed before and after training. Results indicate that performance in all four dimensions improved with training. Training on a control condition, which paralleled the discrimination task but without a grouping component, produced no improvement. In addition, training on only the luminance and orientation dimensions improved performance for those conditions as well as for grouping by color, on which training had not occurred. However, improvement from partial training did not generalize to motion. Results demonstrate that a training protocol emphasizing stimulus integration enhanced perceptual grouping. Results suggest that neural mechanisms mediating grouping by common luminance and/or orientation contribute to those mediating grouping by color but do not share resources for grouping by common motion. Results are consistent with theories of perceptual learning emphasizing plasticity in early visual processing regions.

The chemical properties and microbial community characterization of the thermophilic microaerobic pretreatment process.

PubMed

Fu, Shan-Fei; He, Shuai; Shi, Xiao-Shuang; Katukuri, Naveen Reddy; Dai, Meng; Guo, Rong-Bo

2015-12-01

Thermophilic microaerobic pretreatment (TMP) was recently reported as an efficient pretreatment method of anaerobic digestion (AD). In this study, the chemical properties and microbial community were characterized to reveal how TMP working. Compared with thermophilic treatment under anaerobic condition (TMP0), cellulase activity obviously improved under microaerobic condition (TMP1), which was 10.9-49.0% higher than that of TMP0. Reducing sugar, SCOD and VFAs concentrations of TMP1 were 2.6-8.9%, 1.8-4.8% and 13.8-24% higher than those of TMP0, respectively. TMP gave obvious rise to phylum Firmicutes, which associated with extracellular enzymes production. The proportion of class Bacilli (belongs to phylum Firmicutes and mainly acts during hydrolysis) in TMP1 was 124.89% higher than that of TMP0, which reflected the greater hydrolytic ability under microaerobic condition. The improved abundance of phylum Firmicutes (especially class Bacilli, order Bacillales) under microaerobic condition could be the fundamental reason for the improved AD performance of thermophilic microaerobic pretreated corn straw. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Basic questionnaire and methodological criteria for Surveys on Working Conditions, Employment, and Health in Latin America and the Caribbean].

PubMed

Benavides, Fernando G; Merino-Salazar, Pamela; Cornelio, Cecilia; Assunção, Ada Avila; Agudelo-Suárez, Andrés A; Amable, Marcelo; Artazcoz, Lucía; Astete, Jonh; Barraza, Douglas; Berhó, Fabián; Milián, Lino Carmenate; Delclòs, George; Funcasta, Lorena; Gerke, Johanna; Gimeno, David; Itatí-Iñiguez, María José; Lima, Eduardo de Paula; Martínez-Iñigo, David; Medeiros, Adriane Mesquita de; Orta, Lida; Pinilla, Javier; Rodrigo, Fernando; Rojas, Marianela; Sabastizagal, Iselle; Vallebuona, Clelia; Vermeylen, Greet; Villalobos, Gloria H; Vives, Alejandra

2016-10-10

This article aimed to present a basic questionnaire and minimum methodological criteria for consideration in future Surveys on Working Conditions, Employment, and Health in Latin America and the Caribbean. A virtual and face-to-face consensus process was conducted with participation by a group of international experts who used the surveys available up until 2013 as the point of departure for defining the proposal. The final questionnaire included 77 questions grouped in six dimensions: socio-demographic characteristics of workers and companies; employment conditions; working conditions; health status; resources and preventive activities; and family characteristics. The minimum methodological criteria feature the interviewee's home as the place for the interview and aspects related to the quality of the fieldwork. These results can help improve the comparability of future surveys in Latin America and the Caribbean, which would in turn help improve information on workers' heath in the region.

Thermal Microstructural Stability of AZ31 Magnesium after Severe Plastic Deformation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, John P.; Askari, Hesam A.; Hovanski, Yuri

2015-03-01

Both equal channel angular pressing and friction stir processing have the ability to refine the grain size of twin roll cast AZ31 magnesium and potentially improve its superplastic properties. This work used isochronal and isothermal heat treatments to investigate the microstructural stability of twin roll cast, equal channel angular pressed and friction stir processed AZ31 magnesium. For both heat treatment conditions, it was found that the twin roll casted and equal channel angular pressed materials were more stable than the friction stir processed material. Calculations of the grain growth kinetics showed that severe plastic deformation processing decreased the activation energymore » for grain boundary motion with the equal channel angular pressed material having the greatest Q value of the severely plastically deformed materials and that increasing the tool travel speed of the friction stir processed material improved microstructural stability. The Hollomon-Jaffe parameter was found to be an accurate means of identifying the annealing conditions that will result in substantial grain growth and loss of potential superplastic properties in the severely plastically deformed materials. In addition, Humphreys’s model of cellular microstructural stability accurately predicted the relative microstructural stability of the severely plastically deformed materials and with some modification, closely predicted the maximum grain size ratio achieved by the severely plastically deformed materials.« less

Improved quality of graphene in the absence of hydrogen in a low-temperature growth process using an alcohol precursor

NASA Astrophysics Data System (ADS)

Choi, Kyeonggon; Lee, Kiyeol; Jeong, Jaehoon; Ye, Jongpil

2017-03-01

We present the results of low-temperature growth of graphene on polycrystalline copper foil surfaces at 800 °C by using low-pressure chemical-vapor deposition of alcohol precursors. The structural quality of the graphene sample was found to depend significantly on the ambient conditions during the annealing and the growth processes. The improved quality of graphene grown in an oxidizing environment was found to be associated with a lower nucleation density, suggesting that chemisorbed oxygen atoms play a critical role in determining the quality of graphene.

Calcium phosphates recovery from digester supernatant by fast precipitation and recrystallization

NASA Astrophysics Data System (ADS)

Vasenko, Liubov; Qu, Haiyan

2018-01-01

Conditional solubility of dicalcium phosphate dihydrate (DCPD) and hydroxyapatite (HAp) in digester supernatant was determined as a function of pH and was compared to its conditional solubility in distilled water. Conditional solubility of both substances in digester supernatant at pH >5-6 was higher than their conditional solubility in pure water due to the presence of impurities, and this influence is more significant for HAp. Amorphous CaP was precipitated through a fast precipitation process from digester supernatant with initial total phosphate concentration 0.008 mol/L and 0.015 mol/L and Ca/P ratios 2 and 5. The amorphous CaP can be subsequently recrystallized into crystalline CaP. Obtained amorphous products have Ca/P ratio > 1, which allow performing the recrystallization process without further Ca dosing into the system. Batch recrystallization of the amorphous products resulted in crystallization of HAp, DCPD or their mixture depending on the conditions of the process. Maximum achieved P-recovery was 69.5%. The increase of phosphate concentration and the addition of seeding decreased the yield of the process but promoted crystallization of DCPD. The increase of Ca/P ratio had a positive effect on the total P-recovery. Compared with the direct batch crystallization of CaP from digester supernatant, the two-step process with fast precipitation and recrystallization significantly improved the color of the obtained products.

Modification of polymers by polymeric additives

NASA Astrophysics Data System (ADS)

Nesterov, A. E.; Lebedev, E. V.

1989-08-01

The conditions for the thermodynamic compatibility of polymers and methods for its enhancement are examined. The study of the influence of various factors on the concentration-temperature limits of compatibility, dispersion stabilisation processes, and methods for the improvement of adhesion between phases in mixtures of thermodynamically incompatible polymers is described. Questions concerning the improvement of the physicomechanical characteristics of polymer dispersions are considered. The bibliography includes 200 references.

Smart information system for gachon university gil hospital.

PubMed

Park, Dong Kyun; Jung, Eun Young; Jeong, Byung Hui; Moon, Byung Chan; Kang, Hyung Wook; Tchah, Hann; Han, Gi Seong; Cheng, Woo Sung; Lee, Young Ho

2012-03-01

In this research, the hospital information system of Gachon University Gil hospital is introduced and a future strategy for hospital information systems is proposed. This research introduces the development conditions of hospital information system at Gachon University Gil hospital, information about the development of the enterprise resource planning (ERP), a medical service process improvement system, and the personal health record (PHR) system. The medical service process and work efficiency were improved through the medical service process improvement system, which is the most common hospital information system at Gachon University Gil hospital and which includes an emergency medical service system, an online evaluation system and a round support system. Gachon University Gil hospital developed medical service improvement systems to increase work efficiency of medical team and optimized the systems to prove the availability of high-quality medical services for patients and their families. The PHR-based personalized health care solution is under development and will provide higher quality medical service for more patients in the future.

Smart Information System for Gachon University Gil Hospital

PubMed Central

Jung, Eun Young; Jeong, Byung Hui; Moon, Byung Chan; Kang, Hyung Wook; Tchah, Hann; Han, Gi Seong; Cheng, Woo Sung; Lee, Young Ho

2012-01-01

Objectives In this research, the hospital information system of Gachon University Gil hospital is introduced and a future strategy for hospital information systems is proposed. Methods This research introduces the development conditions of hospital information system at Gachon University Gil hospital, information about the development of the enterprise resource planning (ERP), a medical service process improvement system, and the personal health record (PHR) system. Results The medical service process and work efficiency were improved through the medical service process improvement system, which is the most common hospital information system at Gachon University Gil hospital and which includes an emergency medical service system, an online evaluation system and a round support system. Conclusions Gachon University Gil hospital developed medical service improvement systems to increase work efficiency of medical team and optimized the systems to prove the availability of high-quality medical services for patients and their families. The PHR-based personalized health care solution is under development and will provide higher quality medical service for more patients in the future. PMID:22509476

Improved chemical identification from sensor arrays using intelligent algorithms

NASA Astrophysics Data System (ADS)

Roppel, Thaddeus A.; Wilson, Denise M.

2001-02-01

Intelligent signal processing algorithms are shown to improve identification rates significantly in chemical sensor arrays. This paper focuses on the use of independently derived sensor status information to modify the processing of sensor array data by using a fast, easily-implemented "best-match" approach to filling in missing sensor data. Most fault conditions of interest (e.g., stuck high, stuck low, sudden jumps, excess noise, etc.) can be detected relatively simply by adjunct data processing, or by on-board circuitry. The objective then is to devise, implement, and test methods for using this information to improve the identification rates in the presence of faulted sensors. In one typical example studied, utilizing separately derived, a-priori knowledge about the health of the sensors in the array improved the chemical identification rate by an artificial neural network from below 10 percent correct to over 99 percent correct. While this study focuses experimentally on chemical sensor arrays, the results are readily extensible to other types of sensor platforms.

Incident management successful practices : a cross-cutting study : improving mobility and saving lives

DOT National Transportation Integrated Search

2000-04-01

Incident management is the process of managing multi-agency, multi-jurisdictional responses to highway traffic disruptions. Efficient and coordinated management of incidents reduces their adverse impacts on public safety, traffic conditions, and the ...

Report: Fiscal 2004 and 2003 Financial Statements for the Pesticides Reregistration and Expedited Processing Fund

EPA Pesticide Factsheets

Report #2005-1-00081, May 4, 2005. We identified the following reportable conditions: We could not assess the adequacy of automated controls. EPA needs to improve financial statement preparation and quality control.

Can Pharmacotherapists be Too Supportive? A Process Study of Active Medication and Placebo in the Treatment of Depression

PubMed Central

Strunk, Daniel R.; Stewart, Michael O.; Hollon, Steven D.; DeRubeis, Robert J.; Fawcett, Jan; Amsterdam, Jay D.; Shelton, Richard C.

2013-01-01

Background This study examined therapist-patient interactions during clinical management with anti-depressant medication and pill-placebo. Methods The sample consisted of 80 patients on active medication and 40 patients in a pill-placebo condition from a randomized controlled trial for moderate to severe depression. Pharmacotherapist-patient interactions were characterized using observer ratings of the therapeutic alliance, pharmacotherapist-offered facilitative conditions, pharmacotherapist adherence to clinical management treatment guidelines, and pharmacotherapist competence. Patients, therapists, and raters were blind to treatment condition and outcome. Results Provision of greater nonspecific support (facilitative conditions) in early sessions predicted less subsequent improvement in depressive symptoms for patients receiving pill-placebo but not those receiving active medications, for which none of the process ratings predicted subsequent change. Early symptom change predicted later alliance and adherence in both conditions and therapist competence in the active condition. Conclusions Higher levels of support in early sessions predict poorer subsequent response among placebo patients. It remains unclear whether patients who are likely to be refractory elicit greater nonspecific support or whether the provision of such support has a deleterious effect in unmedicated patients. Differences in treatment process variables between conditions late in treatment are likely to be largely a consequence of symptom relief produced by active medications. PMID:19891806

The Training of Morphological Decomposition in Word Processing and Its Effects on Literacy Skills.

PubMed

Bar-Kochva, Irit; Hasselhorn, Marcus

2017-01-01

This study set out to examine the effects of a morpheme-based training on reading and spelling in fifth and sixth graders ( N = 47), who present poor literacy skills and speak German as a second language. A computerized training, consisting of a visual lexical decision task (comprising 2,880 items, presented in 12 sessions), was designed to encourage fast morphological analysis in word processing. The children were divided between two groups: the one underwent a morpheme-based training, in which word-stems of inflections and derivations were presented for a limited duration, while their pre- and suffixes remained on screen until response. Another group received a control training consisting of the same task, except that the duration of presentation of a non-morphological unit was restricted. In a Word Disruption Task, participants read words under three conditions: morphological separation (with symbols separating between the words' morphemes), non-morphological separation (with symbols separating between non-morphological units of words), and no-separation (with symbols presented at the beginning and end of each word). The group receiving the morpheme-based program improved more than the control group in terms of word reading fluency in the morphological condition. The former group also presented similar word reading fluency after training in the morphological condition and in the no-separation condition, thereby suggesting that the morpheme-based training contributed to the integration of morphological decomposition into the process of word recognition. At the same time, both groups similarly improved in other measures of word reading fluency. With regard to spelling, the morpheme-based training group showed a larger improvement than the control group in spelling of trained items, and a unique improvement in spelling of untrained items (untrained word-stems integrated into trained pre- and suffixes). The results further suggest some contribution of the morpheme-based training to performance in a standardized spelling task. The morpheme-based training did not, however, show any unique effect on comprehension. These results suggest that the morpheme-based training is effective in enhancing some basic literacy skill in the population examined, i.e., morphological analysis in word processing and the access to orthographic representations in spelling, with no specific effects on reading fluency and comprehension.

The Training of Morphological Decomposition in Word Processing and Its Effects on Literacy Skills

PubMed Central

Bar-Kochva, Irit; Hasselhorn, Marcus

2017-01-01

This study set out to examine the effects of a morpheme-based training on reading and spelling in fifth and sixth graders (N = 47), who present poor literacy skills and speak German as a second language. A computerized training, consisting of a visual lexical decision task (comprising 2,880 items, presented in 12 sessions), was designed to encourage fast morphological analysis in word processing. The children were divided between two groups: the one underwent a morpheme-based training, in which word-stems of inflections and derivations were presented for a limited duration, while their pre- and suffixes remained on screen until response. Another group received a control training consisting of the same task, except that the duration of presentation of a non-morphological unit was restricted. In a Word Disruption Task, participants read words under three conditions: morphological separation (with symbols separating between the words’ morphemes), non-morphological separation (with symbols separating between non-morphological units of words), and no-separation (with symbols presented at the beginning and end of each word). The group receiving the morpheme-based program improved more than the control group in terms of word reading fluency in the morphological condition. The former group also presented similar word reading fluency after training in the morphological condition and in the no-separation condition, thereby suggesting that the morpheme-based training contributed to the integration of morphological decomposition into the process of word recognition. At the same time, both groups similarly improved in other measures of word reading fluency. With regard to spelling, the morpheme-based training group showed a larger improvement than the control group in spelling of trained items, and a unique improvement in spelling of untrained items (untrained word-stems integrated into trained pre- and suffixes). The results further suggest some contribution of the morpheme-based training to performance in a standardized spelling task. The morpheme-based training did not, however, show any unique effect on comprehension. These results suggest that the morpheme-based training is effective in enhancing some basic literacy skill in the population examined, i.e., morphological analysis in word processing and the access to orthographic representations in spelling, with no specific effects on reading fluency and comprehension. PMID:29163245

Mindfulness training alters emotional memory recall compared to active controls: support for an emotional information processing model of mindfulness.

PubMed

Roberts-Wolfe, Douglas; Sacchet, Matthew D; Hastings, Elizabeth; Roth, Harold; Britton, Willoughby

2012-01-01

While mindfulness-based interventions have received widespread application in both clinical and non-clinical populations, the mechanism by which mindfulness meditation improves well-being remains elusive. One possibility is that mindfulness training alters the processing of emotional information, similar to prevailing cognitive models of depression and anxiety. The aim of this study was to investigate the effects of mindfulness training on emotional information processing (i.e., memory) biases in relation to both clinical symptomatology and well-being in comparison to active control conditions. Fifty-eight university students (28 female, age = 20.1 ± 2.7 years) participated in either a 12-week course containing a "meditation laboratory" or an active control course with similar content or experiential practice laboratory format (music). Participants completed an emotional word recall task and self-report questionnaires of well-being and clinical symptoms before and after the 12-week course. Meditators showed greater increases in positive word recall compared to controls [F(1, 56) = 6.6, p = 0.02]. The meditation group increased significantly more on measures of well-being [F(1, 56) = 6.6, p = 0.01], with a marginal decrease in depression and anxiety [F(1, 56) = 3.0, p = 0.09] compared to controls. Increased positive word recall was associated with increased psychological well-being (r = 0.31, p = 0.02) and decreased clinical symptoms (r = -0.29, p = 0.03). Mindfulness training was associated with greater improvements in processing efficiency for positively valenced stimuli than active control conditions. This change in emotional information processing was associated with improvements in psychological well-being and less depression and anxiety. These data suggest that mindfulness training may improve well-being via changes in emotional information processing. Future research with a fully randomized design will be needed to clarify the possible influence of self-selection.

Leadership, safety climate, and continuous quality improvement: impact on process quality and patient safety.

PubMed

McFadden, Kathleen L; Stock, Gregory N; Gowen, Charles R

2014-10-01

Successful amelioration of medical errors represents a significant problem in the health care industry. There is a need for greater understanding of the factors that lead to improved process quality and patient safety outcomes in hospitals. We present a research model that shows how transformational leadership, safety climate, and continuous quality improvement (CQI) initiatives are related to objective quality and patient safety outcome measures. The proposed framework is tested using structural equation modeling, based on data collected for 204 hospitals, and supplemented with objective outcome data from the Centers for Medicare and Medicaid Services. The results provide empirical evidence that a safety climate, which is connected to the chief executive officer's transformational leadership style, is related to CQI initiatives, which are linked to improved process quality. A unique finding of this study is that, although CQI initiatives are positively associated with improved process quality, they are also associated with higher hospital-acquired condition rates, a measure of patient safety. Likewise, safety climate is directly related to improved patient safety outcomes. The notion that patient safety climate and CQI initiatives are not interchangeable or universally beneficial is an important contribution to the literature. The results confirm the importance of using CQI to effectively enhance process quality in hospitals, and patient safety climate to improve patient safety outcomes. The overall pattern of findings suggests that simultaneous implementation of CQI initiatives and patient safety climate produces greater combined benefits.

Leadership, safety climate, and continuous quality improvement: impact on process quality and patient safety.

PubMed

McFadden, Kathleen L; Stock, Gregory N; Gowen, Charles R

2015-01-01

Successful amelioration of medical errors represents a significant problem in the health care industry. There is a need for greater understanding of the factors that lead to improved process quality and patient safety outcomes in hospitals. We present a research model that shows how transformational leadership, safety climate, and continuous quality improvement (CQI) initiatives are related to objective quality and patient safety outcome measures. The proposed framework is tested using structural equation modeling, based on data collected for 204 hospitals, and supplemented with objective outcome data from the Centers for Medicare and Medicaid Services. The results provide empirical evidence that a safety climate, which is connected to the chief executive officer's transformational leadership style, is related to CQI initiatives, which are linked to improved process quality. A unique finding of this study is that, although CQI initiatives are positively associated with improved process quality, they are also associated with higher hospital-acquired condition rates, a measure of patient safety. Likewise, safety climate is directly related to improved patient safety outcomes. The notion that patient safety climate and CQI initiatives are not interchangeable or universally beneficial is an important contribution to the literature. The results confirm the importance of using CQI to effectively enhance process quality in hospitals, and patient safety climate to improve patient safety outcomes. The overall pattern of findings suggests that simultaneous implementation of CQI initiatives and patient safety climate produces greater combined benefits.

Evaluation of biochar-ultrafiltration membrane processes for humic acid removal under various hydrodynamic, pH, ionic strength, and pressure conditions.

PubMed

Shankar, Vaibhavi; Heo, Jiyong; Al-Hamadani, Yasir A J; Park, Chang Min; Chu, Kyoung Hoon; Yoon, Yeomin

2017-07-15

The performance of an ultrafiltration (UF)-biochar process was evaluated in comparison with a UF membrane process for the removal of humic acid (HA). Bench-scale UF experiments were conducted to study the rejection and flux trends under various hydrodynamic, pH, ionic strength, and pressure conditions. The resistance-in-series model was used to evaluate the processes and it showed that unlike stirred conditions, where low fouling resistance was observed (28.7 × 10 12  m -1 to 32.5 × 10 12  m -1 ), higher values and comparable trends were obtained for UF-biochar and UF alone for unstirred conditions (28.7 × 10 12  m -1 to 32.5 × 10 12  m -1 ). Thus, the processes were further evaluated under unstirred conditions. Additionally, total fouling resistance was decreased in the presence of biochar by 6%, indicating that HA adsorption by biochar could diminish adsorption fouling on the UF membrane and thus improve the efficiency of the UF-biochar process. The rejection trends of UF-biochar and UF alone were similar in most cases, whereas UF-biochar showed a noticeable increase in flux of around 18-25% under various experimental conditions due to reduced membrane fouling. Three-cycle filtration tests further demonstrated that UF-biochar showed better membrane recovery and antifouling capability by showing more HA rejection (3-5%) than UF membrane alone with each subsequent cycle of filtration. As a result of these findings, the UF-biochar process may potentially prove be a viable treatment option for the removal of HA from water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Occupational Noise Reduction in CNC Striping Process

NASA Astrophysics Data System (ADS)

Mahmad Khairai, Kamarulzaman; Shamime Salleh, Nurul; Razlan Yusoff, Ahmad

2018-03-01

Occupational noise hearing loss with high level exposure is common occupational hazards. In CNC striping process, employee that exposed to high noise level for a long time as 8-hour contributes to hearing loss, create physical and psychological stress that reduce productivity. In this paper, CNC stripping process with high level noises are measured and reduced to the permissible noise exposure. First condition is all machines shutting down and second condition when all CNC machine under operations. For both conditions, noise exposures were measured to evaluate the noise problems and sources. After improvement made, the noise exposures were measured to evaluate the effectiveness of reduction. The initial average noise level at the first condition is 95.797 dB (A). After the pneumatic system with leakage was solved, the noise reduced to 55.517 dB (A). The average noise level at the second condition is 109.340 dB (A). After six machines were gathered at one area and cover that area with plastic curtain, the noise reduced to 95.209 dB (A). In conclusion, the noise level exposure in CNC striping machine is high and exceed the permissible noise exposure can be reduced to acceptable levels. The reduction of noise level in CNC striping processes enhanced productivity in the industry.

Improvement of Stability and Antioxidant Activities by Using Phycocyanin - Chitosan Encapsulation Technique

NASA Astrophysics Data System (ADS)

Suzery, Meiny; Hadiyanto; Majid, Dian; Setyawan, Deny; Sutanto, Heri

2017-02-01

Encapsulation is a coating process to improve the stability of bioactive compounds. Phycocyanin with high antioxidant activity has been encapsulated with chitosan in microcapsules form. In this study aims to determine the best conditions in the encapsulation process using the extrusion method, characterization of the physicochemical properties of the microcapsules, antioxidant activity test using DPPH, in vitro release performance and evaluate the storage stability against temperature. The results of the encapsulation process is obtained: Na-TPP is better than Na-citrate as crosslinker and chitosan content 3% as a coating with ratio of chitosan to phycocyanin ratio 1: 1. Test of antioxidant activity also showed encapsulation with chitosan content 3% has the highest antioxidant activity. Morphological analysis microcapsules were found to have compact spherical shape with diameter range 900-1000 µm. In vitro release testing showed a quick release in an acidic environment (SGF) for 2 hours and slowly release under alkaline conditions (SIF) for 8 hours under mechanical stirring at 37°C. Phycocyanin much more stable against temperature during storage in microcapsules.

Process for fabricating ZnO-based varistors

DOEpatents

Lauf, R.J.

The invention is a process for producing ZnO-based varistors incorporating a metal oxide dopant. In one form, the invention comprises providing a varistor powder mix of colloidal particles of ZnO and metal-oxide dopants including Bi/sub 2/O/sub 3/. The mix is hot-pressed to form a compact at temperatures below 850/sup 0/C and under conditions effecting reduction of the ZnO to sub-stoichiometric oxide. This promotes densification while restricting liquid formation and grain growth. The compact then is heated under conditions restoring the zinc oxide to stoichiometric composition, thus improving the varistor properties of the compact. The process produces fine-grain varistors characterized by a high actual breakdown voltage and a high average breakdown voltage per individual grain boundary.

Processing of nutritious, safe and acceptable foods from cells candidate crops

NASA Astrophysics Data System (ADS)

Fu, B.; Nelson, P. E.; Irvine, R.; Kanach, L. L.

A controlled ecological life-support system (CELSS) is required to sustain life for long-duration space missions. The challenge is preparing a wide variety of tasty, familiar, and nutritious foods from CELSS candidate crops under space environmental conditions. Conventional food processing technologies will have to be modified to adapt to the space environment. Extrusion is one of the processes being examined as a means of converting raw plant biomass into familiar foods. A nutrition-improved pasta has been developed using cowpea as a replacement for a portion of the durum semolina. A freeze-drying system that simulates the space conditions has also been developed. Other technologies that would fulfill the requirements of a CELSS will also be addressed.

Processing of nutritious, safe and acceptable foods from CELSS candidate crops

NASA Technical Reports Server (NTRS)

Fu, B.; Nelson, P. E.; Irvine, R.; Kanach, L. L.; Mitchell, C. A. (Principal Investigator)

1996-01-01

A controlled ecological life-support system (CELSS) is required to sustain life for long-duration space missions. The challenge is preparing a wide variety of tasty, familiar, and nutritious foods from CELSS candidate crops under space environmental conditions. Conventional food processing technologies will have to be modified to adapt to the space environment. Extrusion is one of the processes being examined as a means of converting raw plant biomass into familiar foods. A nutrition-improved pasta has been developed using cowpea as a replacement for a portion of the durum semolina. A freeze-drying system that simulates the space conditions has also been developed. Other technologies that would fulfill the requirements of a CELSS will also be addressed.

Precision of computer vision systems for real-time inspection of contact wire wear in railways

NASA Astrophysics Data System (ADS)

Borromeo, Susana; Aparicio, Jose L.

2005-02-01

This paper is oriented to study techniques to improve the precision of the systems for wear measurement of contact wire in the railways. The problematic of wear measurement characterized by some important determining factors like rate of sampling and auscultation conditions is studied in detail. The different solutions to resolve the problematic successfully are examined. Issues related to image acquisition and image processing are discussed. Type of illumination and sensors employed, image processing hardware and image processing algorithms are some topics studied. Once analyzed each one factor which have influence on the precision of the measurement system, there are proposed an assembly of solutions that allow to optimize the conditions under which the inspection can be carried out.

Process for fabricating ZnO-based varistors

DOEpatents

Lauf, Robert J.

1985-01-01

The invention is a process for producing ZnO-based varistors incorporating a metal oxide dopant. In one form, the invention comprises providing a varistor powder mix of colloidal particles of ZnO and metal-oxide dopants including Bi.sub.2 O.sub.3. The mix is hot-pressed to form a compact at temperatures below 850.degree. C. and under conditions effecting reduction of the ZnO to sub-stoichiometric oxide. This promotes densification while restricting liquid formation and grain growth. The compact then is heated under conditions restoring the zinc oxide to stoichiometric composition, thus improving the varistor properties of the compact. The process produces fine-grain varistors characterized by a high actual breakdown voltage and a high average breakdown voltage per individual grain boundary.

Using Lean methodologies to streamline processing of requests for durable medical equipment and supplies for children with complex conditions.

PubMed

Fields, Elise; Neogi, Smriti; Schoettker, Pamela J; Lail, Jennifer

2017-12-12

An improvement team from the Complex Care Center at our large pediatric medical center participated in a 60-day initiative to use Lean methodologies to standardize their processes, eliminate waste and improve the timely and reliable provision of durable medical equipment and supplies. The team used value stream mapping to identify processes needing improvement. Improvement activities addressed the initial processing of a request, provider signature on the form, returning the form to the sender, and uploading the completed documents to the electronic medical record. Data on lead time (time between receiving a request and sending the completed request to the Health Information Management department) and process time (amount of time the staff worked on the request) were collected via manual pre- and post-time studies. Following implementation of interventions, the median lead time for processing durable medical equipment and supply requests decreased from 50 days to 3 days (p < 0.0001). Median processing time decreased from 14min to 9min (p < 0.0001). The decrease in processing time realized annual cost savings of approximately $11,000. Collaborative leadership and multidisciplinary training in Lean methods allowed the CCC staff to incorporate common sense, standardize practices, and adapt their work environment to improve the timely and reliable provision of equipment and supplies that are essential for their patients. The application of Lean methodologies to processing requests for DME and supplies could also result in a natural spread to other paperwork and requests, thus avoiding delays and potential risk for clinical instability or deterioration. Copyright © 2017 Elsevier Inc. All rights reserved.

Noise sensitivity of portfolio selection in constant conditional correlation GARCH models

NASA Astrophysics Data System (ADS)

Varga-Haszonits, I.; Kondor, I.

2007-11-01

This paper investigates the efficiency of minimum variance portfolio optimization for stock price movements following the Constant Conditional Correlation GARCH process proposed by Bollerslev. Simulations show that the quality of portfolio selection can be improved substantially by computing optimal portfolio weights from conditional covariances instead of unconditional ones. Measurement noise can be further reduced by applying some filtering method on the conditional correlation matrix (such as Random Matrix Theory based filtering). As an empirical support for the simulation results, the analysis is also carried out for a time series of S&P500 stock prices.

Two-stage anaerobic and post-aerobic mesophilic digestion of sewage sludge: Analysis of process performance and hygienization potential.

PubMed

Tomei, M Concetta; Mosca Angelucci, Domenica; Levantesi, Caterina

2016-03-01

Sequential anaerobic-aerobic digestion has been demonstrated to be effective for enhanced sludge stabilization, in terms of increased solid reduction and improvement of sludge dewaterability. In this study, we propose a modified version of the sequential anaerobic-aerobic digestion process by operating the aerobic step under mesophilic conditions (T=37 °C), in order to improve the aerobic degradation kinetics of soluble and particulate chemical oxygen demand (COD). Process performance has been assessed in terms of "classical parameters" such as volatile solids (VS) removal, biogas production, COD removal, nitrogen species, and polysaccharide and protein fate. The aerobic step was operated under intermittent aeration to achieve nitrogen removal. Aerobic mesophilic conditions consistently increased VS removal, providing 32% additional removal vs. 20% at 20 °C. Similar results were obtained for nitrogen removal, increasing from 64% up to 99% at the higher temperature. Improved sludge dewaterability was also observed with a capillary suction time decrease of ~50% during the mesophilic aerobic step. This finding may be attributable to the decreased protein content in the aerobic digested sludge. The post-aerobic digestion exerted a positive effect on the reduction of microbial indicators while no consistent improvement of hygienization related to the increased temperature was observed. The techno-economic analysis of the proposed digestion layout showed a net cost saving for sludge disposal estimated in the range of 28-35% in comparison to the single-phase anaerobic digestion. Copyright © 2015 Elsevier B.V. All rights reserved.

Effects of Inhibition Conditions on Anammox process

NASA Astrophysics Data System (ADS)

Xie, Haitao; Ji, Dandan; Zang, Lihua

2017-12-01

Anaerobic ammonium oxidation (Anammox) is a very suitable process for the treatment of nitrogen-rich wastewater, which is a promising new biological nitrogen removal process, and has a good application prospects. However, the Anammox process is inhibited by many factors, which hinders the process improvement and the application of the Anammox process. Such as organic,temperature,salts,heavy metals, phosphates, sulfides, pH and other inhibitors are usually present in practical applications. We have reviewed the previous researches on the inhibition of Anammox processes. The effect of the substrate on the anaerobic oxide is mainly caused by free ammonia or nitrite nitrogen. Most heavy metals inhibit Anammox growth and activity. The inhibition of organic matter depends on the content of organic matter and species. High salinity inhibits Anammox activity. Dissolved oxygen allows the flora to be in a balanced state. The optimum pH and temperature, as well as other factors, can provide a good growth environment for Anammox. The knowledge of inhibition on Anammox will help prevent the application and improvement of the Anammox process.

[Cancer screening in clinical practice: the value of shared decision-making].

PubMed

Cornuz, Jacques; Junod, Noëlle; Pasche, Olivier; Guessous, Idris

2010-07-14

Shared decision-making approach to uncertain clinical situations such as cancer screening seems more appropriate than ever. Shared decision making can be defined as an interactive process where physician and patient share all the stages of the decision making process. For patients who wish to be implicated in the management of their health conditions, physicians might express difficulty to do so. Use of patient decision aids appears to improve such process of shared decision making.

Hybrid Adsorption-Membrane Biological Reactors for Improved Performance and Reliability of Perchlorate Removal Processes

DTIC Science & Technology

2008-12-01

to reduce effluent perchlorate spikes by up to 97% in comparison to a conventional MBR that was subject to sudden changes in influent conditions...biological reactor (HAMBgR). The HAMBgR process integrates a granular adsorptive media into the mixed liquor of a membrane bioreactor ( MBR ), which...although concentrated brine disposal can be problematic. In this study, we measured the performance of a conventional MBR and a HAMBgR process and

Assessment of critical-fluid extractions in the process industries

NASA Technical Reports Server (NTRS)

1982-01-01

The potential for critical-fluid extraction as a separation process for improving the productive use of energy in the process industries is assessed. Critical-fluid extraction involves the use of fluids, normally gaseous at ambient conditions, as extraction solvents at temperatures and pressures around the critical point. Equilibrium and kinetic properties in this regime are very favorable for solvent applications, and generally allow major reductions in the energy requirements for separating and purifying chemical component of a mixture.

Correlation study of actual temperature profile and in-line metrology measurements for within-wafer uniformity improvement and wafer edge yield enhancement (Conference Presentation)

NASA Astrophysics Data System (ADS)

Fang, Fang; Vaid, Alok; Vinslava, Alina; Casselberry, Richard; Mishra, Shailendra; Dixit, Dhairya; Timoney, Padraig; Chu, Dinh; Porter, Candice; Song, Da; Ren, Zhou

2018-03-01

It is getting more important to monitor all aspects of influencing parameters in critical etch steps and utilize them as tuning knobs for within-wafer uniformity improvement and wafer edge yield enhancement. Meanwhile, we took a dive in pursuing "measuring what matters" and challenged ourselves for more aspects of signals acquired in actual process conditions. Among these factors which are considered subtle previously, we identified Temperature, especially electrostatic chuck (ESC) Temperature measurement in real etch process conditions have direct correlation to in-line measurements. In this work, we used SensArray technique (EtchTemp-SE wafer) to measure ESC temperature profile on a 300mm wafer with plasma turning on to reproduce actual temperature pattern on wafers in real production process conditions. In field applications, we observed substantial correlation between ESC temperature and in-line optical metrology measurements and since temperature is a process factor that can be tuning through set-temperature modulations, we have identified process knobs with known impact on physical profile variations. Furthermore, ESC temperature profile on a 300mm wafer is configured as multiple zones upon radius and SensArray measurements mechanism could catch such zonal distribution as well, which enables detailed temperature modulations targeting edge ring only where most of chips can be harvested and critical zone for yield enhancement. Last but not least, compared with control reference (ESC Temperature in static plasma-off status), we also get additional factors to investigate in chamber-to-chamber matching study and make process tool fleet match on the basis really matters in production. KLA-Tencor EtchTemp-SE wafer enables Plasma On wafer temperature monitoring of silicon etch process. This wafer is wireless and has 65 sensors with measurement range from 20 to 140°C. the wafer is designed to run in real production recipe plasma on condition with maximum RF power up to 7KW. The wafer surface is coated with Yttrium oxide film which allows Silicon Etch chemistry. At Fab-8, we carried investigations in 14 nm FEOL critical etch process which has direct impact on yield, using SensorArray EtchTemp-SE wafer, we measured ESC temperature profile across multiple chambers, for both plasma on and plasma off, promising results achieved on chamber temperature signature identification, guideline for chamber to chamber matching improvement. Correlation between wafer mean temperature and determining criticality-process parameters of recess depth and CD is observed. Furthermore, detail zonal temperature/profile correlation is investigated to identify individual correlation in each chuck zone, and provided unique process knobs corresponding to each chunk. Meanwhile, passive ESC Chuck DOE was done to modulate wafer temperature at different zones, and Sensor Array wafer measurements verified temperature responding well with the ESC set point. Correlation R2 = 0.9979 for outer ring and R2 = 0.9981 for Mid Outer ring is observed, as shown in . Experiments planning to modulate edge zone ESC temperature to tune profile within-wafer uniformity and prove gain in edge yield enhancement and to improve edge yield is underway.

Virtual reality and gaming systems to improve walking and mobility for people with musculoskeletal and neuromuscular conditions.

PubMed

Deutsch, Judith E

2009-01-01

Improving walking for individuals with musculoskeletal and neuromuscular conditions is an important aspect of rehabilitation. The capabilities of clinicians who address these rehabilitation issues could be augmented with innovations such as virtual reality gaming based technologies. The chapter provides an overview of virtual reality gaming based technologies currently being developed and tested to improve motor and cognitive elements required for ambulation and mobility in different patient populations. Included as well is a detailed description of a single VR system, consisting of the rationale for development and iterative refinement of the system based on clinical science. These concepts include: neural plasticity, part-task training, whole task training, task specific training, principles of exercise and motor learning, sensorimotor integration, and visual spatial processing.

Computerized clinical decision support systems for primary preventive care: a decision-maker-researcher partnership systematic review of effects on process of care and patient outcomes.

PubMed

Souza, Nathan M; Sebaldt, Rolf J; Mackay, Jean A; Prorok, Jeanette C; Weise-Kelly, Lorraine; Navarro, Tamara; Wilczynski, Nancy L; Haynes, R Brian

2011-08-03

Computerized clinical decision support systems (CCDSSs) are claimed to improve processes and outcomes of primary preventive care (PPC), but their effects, safety, and acceptance must be confirmed. We updated our previous systematic reviews of CCDSSs and integrated a knowledge translation approach in the process. The objective was to review randomized controlled trials (RCTs) assessing the effects of CCDSSs for PPC on process of care, patient outcomes, harms, and costs. We conducted a decision-maker-researcher partnership systematic review. We searched MEDLINE, EMBASE, Ovid's EBM Reviews Database, Inspec, and other databases, as well as reference lists through January 2010. We contacted authors to confirm data or provide additional information. We included RCTs that assessed the effect of a CCDSS for PPC on process of care and patient outcomes compared to care provided without a CCDSS. A study was considered to have a positive effect (i.e., CCDSS showed improvement) if at least 50% of the relevant study outcomes were statistically significantly positive. We added 17 new RCTs to our 2005 review for a total of 41 studies. RCT quality improved over time. CCDSSs improved process of care in 25 of 40 (63%) RCTs. Cumulative scientifically strong evidence supports the effectiveness of CCDSSs for screening and management of dyslipidaemia in primary care. There is mixed evidence for effectiveness in screening for cancer and mental health conditions, multiple preventive care activities, vaccination, and other preventive care interventions. Fourteen (34%) trials assessed patient outcomes, and four (29%) reported improvements with the CCDSS. Most trials were not powered to evaluate patient-important outcomes. CCDSS costs and adverse events were reported in only six (15%) and two (5%) trials, respectively. Information on study duration was often missing, limiting our ability to assess sustainability of CCDSS effects. Evidence supports the effectiveness of CCDSSs for screening and treatment of dyslipidaemia in primary care with less consistent evidence for CCDSSs used in screening for cancer and mental health-related conditions, vaccinations, and other preventive care. CCDSS effects on patient outcomes, safety, costs of care, and provider satisfaction remain poorly supported.

Recent Advances in Synthesis and Characterization of SWCNTs Produced by Laser Oven Process

NASA Technical Reports Server (NTRS)

Aepalli, Sivaram

2004-01-01

Results from the parametric study of the two-laser oven process indicated possible improvements with flow conditions and laser characteristics. Higher flow rates, lower operating pressures coupled with changes in flow tube material are found to improve the nanotube yields. The collected nanotube material is analyzed using a combination of characterization techniques including SEM, TEM, TGA, Raman and UV-VIS-NIR to estimate the purity of the samples. In-situ diagnostics of the laser oven process is now extended to include the surface temperature of the target material. Spectral emission from the target surface is compared with black body type emission to estimate the temperature. The surface temperature seemed to correlate well with the ablation rate as well as the quality of the SWCNTs. Recent changes in improving the production rate by rastering the target and using cw laser will be presented.

Recent Advances in Synthesis and Characterization of SWCNTs produced by laser oven process

NASA Technical Reports Server (NTRS)

Arepalli, Sivaram

2004-01-01

Results from the parametric study of the two-laser oven process indicated possible improvements with flow conditions and laser characteristics (ref. 1). Higher flow rates, lower operating pressures coupled with changes in flow tube material are found to improve the nanotube yields. The collected nanotube material is analyzed using a combination of characterization techniques including SEM, TEM, TGA, Raman and UV-VIS-NIR to estimate the purity of the samples. Insitu diagnostics of the laser oven process is now extended to include the surface temperature of the target material. Spectral emission from the target surface is compared with black body type emission to estimate the temperature. The surface temperature seemed to correlate well with the ablation rate as well as the quality of the SWCNTs. Recent changes in improving the production rate by rastering the target and using cw laser will be presented.

Evaluation of olivine refractories for TES

NASA Astrophysics Data System (ADS)

Gay, B. M.; Cochrane, R. L.; Palmour, H., III; Paisley, M. J.

1982-02-01

The principal objectives of this program are to (1) experimentally determine the degree of improvement in thermal and mechanical performance that can be obtained with an olivine thermal storage brick made of domestic materials using advanced processing techniques compared with state-of-the-art as represented by commercial European bricks, (2) conduct an assessment of existing German ceramic process technology and determine its adaptability to domestic raw materials and manufacturing practices, and (3) investigate, on a limited basis, method for further improvement of domestic-olivine brick. To date, accomplishments include (1) installation of improved, computer-based instrumentation, (2) the use of this system to determine performance characteristics of a set of heat storage refractories under cyclic use conditions, (3) acquisition of the services of a knowledgeable European consultant, (4) continued lab-scale process/property optimization studies, and (5) comparative testing of olivine-based and magnesite-based heat storage refractories in the calorimetric test facility at Purdue University.

Dopamine treatment and cognitive functioning in individuals with Parkinson's disease: the "cognitive flexibility" hypothesis seems to work.

PubMed

Costa, Alberto; Peppe, Antonella; Mazzù, Ilenia; Longarzo, Mariachiara; Caltagirone, Carlo; Carlesimo, Giovanni A

2014-01-01

Previous data suggest that (i) dopamine modulates the ability to implement nonroutine schemata and update operations (flexibility processes) and that (ii) dopamine-related improvement may be related to baseline dopamine levels in target pathways (inverted U-shaped hypothesis). To investigate above hypotheses in individuals with Parkinson's disease (PD). Twenty PD patients were administered tasks varying as to flexibility load in two treatment conditions: (i) "off" condition, about 18 hours after dopamine dose and (ii) "on" condition, after dopamine administration. PD patients were separated into two groups: low performers (i.e., performance on Digit Span Backward below the sample mean) and high performers (i.e., performance above the mean). Twenty healthy individuals performed the tasks in two sessions without taking drugs. Passing from the "off" to the "on" state, only low performer PD patients significantly improved their performance on high-flexibility measures (interference condition of the Stroop test; P < 0.05); no significant effect was found on low-flexibility tasks. These findings document that high-flexibility processes are sensitive to dopamine neuromodulation in the early phases of PD. This is in line with the hypothesis that striatal dopamine pathways, affected early by PD, are precociously implicated in the expression of cognitive disorders in these individuals.

Fuzzy control of burnout of multilayer ceramic actuators

NASA Astrophysics Data System (ADS)

Ling, Alice V.; Voss, David; Christodoulou, Leo

1996-08-01

To improve the yield and repeatability of the burnout process of multilayer ceramic actuators (MCAs), an intelligent processing of materials (IPM-based) control system has been developed for the manufacture of MCAs. IPM involves the active (ultimately adaptive) control of a material process using empirical or analytical models and in situ sensing of critical process states (part features and process parameters) to modify the processing conditions in real time to achieve predefined product goals. Thus, the three enabling technologies for the IPM burnout control system are process modeling, in situ sensing and intelligent control. This paper presents the design of an IPM-based control strategy for the burnout process of MCAs.

Accomplishing much in a short time: use of a rapid improvement event to redesign the assessment and treatment of patients with alcohol withdrawal.

PubMed

Sankoff, Jeffrey; Taub, Julie; Mintzer, David

2013-01-01

The use of Lean tools for quality improvement and process refinement is gaining acceptance in many health care institutions. Traditionally, these tools are used to apply incremental changes to established processes in order to reduce waste and improve quality. In this article, the authors describe a novel Lean methodology, the Rapid Improvement Event (RIE), used in a unique way to develop a new treatment protocol for a specific medical condition: alcohol withdrawal. The RIE allowed for the collaboration of a multidisciplinary group of providers invested in the success of a new protocol for alcohol withdrawal that spans areas from the emergency department to the inpatient ward at an inner-city safety net hospital. It also allowed for the definition of measures for its success once it is implemented.

Effect of fabrication process on physical and mechanical properties of tungsten carbide - cobalt composite: A review

NASA Astrophysics Data System (ADS)

Mahaidin, Ahmad Aswad; Jaafar, Talib Ria; Selamat, Mohd Asri; Budin, Salina; Sulaiman, Zaim Syazwan; Hamid, Mohamad Hasnan Abdul

2017-12-01

WC-Co, which is also known as cemented carbide, is widely used in metal cutting industry and wear related application due to their excellent mechanical properties. Manufacturing industries are focusing on improving productivity and reducing operational cost with machining operation is considered as one of the factors. Thus, machining conditions are becoming more severe and required better cutting tool bit with improved mechanical properties to withstand high temperature operation. Numerous studies have been made over the generation for further improvement of cemented carbide properties to meet the constant increase in demand. However, the results of these studies vary due to different process parameters and manufacturing technology. This paper summarizes the studies to improve the properties of WC-Co composite using different consolidation (powder size, mixing method, formulation, etc) and sintering parameters (temperature, time, atmosphere, etc).

Effect of torrefaction conditions on greenhouse crop residue: Optimization of conditions to upgrade solid characteristics.

PubMed

Iáñez-Rodríguez, Irene; Martín-Lara, María Ángeles; Blázquez, Gabriel; Pérez, Antonio; Calero, Mónica

2017-11-01

This work investigated the possibility of using a greenhouse crop waste as a fuel, since it is an abundant residue in the Mediterranean area of Spain. The residue is mainly composed by biomass with a little quantity of plastic. The physical and chemical characteristics of the biomass were determined by elemental analysis, proximate analysis, FT-IR, FE-SEM and thermogravimetry. Additionally, a torrefaction process was carried out as a pre-treatment to improve the energy properties of the biomass material. The optimal conditions (time and temperature) of torrefaction were found to be 263°C and 15min using the gain and loss method. Further studies were carried out with the sample prepared with the nearest conditions to the optimal in order to determine the effect of the plastic fraction in the characteristics and torrefaction process of the waste studied. Copyright © 2017 Elsevier Ltd. All rights reserved.

Hypothesizing the body's genius to trigger and self-organize its healing: 25 years using a standardized neurophysics therapy

PubMed Central

Ross, Sara N.; Ware, Ken

2013-01-01

We aim for this contribution to operate bi-directionally, both as a “bedside to bench” reverse-translational fractal physiological hypothesis and as a methodological innovation to inform clinical practice. In 25 years using gym equipment therapeutically in non-research settings, the standardized therapy is consistently observed to trigger universal responses of micro to macro waves of system transition dynamics in the human nervous system. These are associated with observably desirable impacts on disorders, injuries, diseases, and athletic performance. Requisite conditions are therapeutic coaching, erect posture, extremely slow movements in mild resistance exercises, and executive control over arousal and attention. To motivate research into the physiological improvements and in validation studies, we integrate from across disciplines to hypothesize explanations for the relationships among the methods, the system dynamics, and evident results. Key hypotheses include: (1) Correctly-directed system efforts may reverse a system's heretofore misdirected efforts, restoring healthier neurophysiology. (2) The enhanced information processing accompanying good posture is an essential initial condition. (3) Behaviors accompanying exercises performed with few degrees of freedom amplify information processing, triggering destabilization and transition dynamics. (4) Executive control over arousal and attention is essential to release system constraints, amplifying and complexifying information. (5) The dynamics create necessary and in many cases evidently sufficient conditions for the body to resolve or improve its own conditions within often short time periods. Literature indicates how the human system possesses material self-awareness. A broad explanation for the nature and effects of the therapy appears rooted in the cascading recursions of the systems' dynamics, which appear to trigger health-fostering self-reorganizing processes when this therapy provides catalytic initial conditions. PMID:24312056

Is transcranial direct current stimulation a potential method for improving response inhibition?☆

PubMed Central

Kwon, Yong Hyun; Kwon, Jung Won

2013-01-01

Inhibitory control of movement in motor learning requires the ability to suppress an inappropriate action, a skill needed to stop a planned or ongoing motor response in response to changes in a variety of environments. This study used a stop-signal task to determine whether transcranial direct-current stimulation over the pre-supplementary motor area alters the reaction time in motor inhibition. Forty healthy subjects were recruited for this study and were randomly assigned to either the transcranial direct-current stimulation condition or a sham-transcranial direct-current stimulation condition. All subjects consecutively performed the stop-signal task before, during, and after the delivery of anodal transcranial direct-current stimulation over the pre-supplementary motor area (pre-transcranial direct-current stimulation phase, transcranial direct-current stimulation phase, and post-transcranial direct-current stimulation phase). Compared to the sham condition, there were significant reductions in the stop-signal processing times during and after transcranial direct-current stimulation, and change times were significantly greater in the transcranial direct-current stimulation condition. There was no significant change in go processing-times during or after transcranial direct-current stimulation in either condition. Anodal transcranial direct-current stimulation was feasibly coupled to an interactive improvement in inhibitory control. This coupling led to a decrease in the stop-signal process time required for the appropriate responses between motor execution and inhibition. However, there was no transcranial direct-current stimulation effect on the no-signal reaction time during the stop-signal task. Transcranial direct-current stimulation can adjust certain behaviors, and it could be a useful clinical intervention for patients who have difficulties with response inhibition. PMID:25206399

Is transcranial direct current stimulation a potential method for improving response inhibition?

PubMed

Kwon, Yong Hyun; Kwon, Jung Won

2013-04-15

Inhibitory control of movement in motor learning requires the ability to suppress an inappropriate action, a skill needed to stop a planned or ongoing motor response in response to changes in a variety of environments. This study used a stop-signal task to determine whether transcranial direct-current stimulation over the pre-supplementary motor area alters the reaction time in motor inhibition. Forty healthy subjects were recruited for this study and were randomly assigned to either the transcranial direct-current stimulation condition or a sham-transcranial direct-current stimulation condition. All subjects consecutively performed the stop-signal task before, during, and after the delivery of anodal transcranial direct-current stimulation over the pre-supplementary motor area (pre-transcranial direct-current stimulation phase, transcranial direct-current stimulation phase, and post-transcranial direct-current stimulation phase). Compared to the sham condition, there were significant reductions in the stop-signal processing times during and after transcranial direct-current stimulation, and change times were significantly greater in the transcranial direct-current stimulation condition. There was no significant change in go processing-times during or after transcranial direct-current stimulation in either condition. Anodal transcranial direct-current stimulation was feasibly coupled to an interactive improvement in inhibitory control. This coupling led to a decrease in the stop-signal process time required for the appropriate responses between motor execution and inhibition. However, there was no transcranial direct-current stimulation effect on the no-signal reaction time during the stop-signal task. Transcranial direct-current stimulation can adjust certain behaviors, and it could be a useful clinical intervention for patients who have difficulties with response inhibition.

Optical Processing.

DTIC Science & Technology

1986-06-01

Further improvements are clearly necessary. 2.2.2 Future Work It would appear that transverse cross-talk is a serious problem in thermally based bistable... manufacturing purposes except under an agreement or with the consent in writing of Ferranti pic and then only on the condition that this notice is...applications which might: (a) appear to benefit from the advantages offered by optical processing (such as large parallelism and dense global inter

Engineering baker's yeast: room for improvement.

PubMed

Randez-Gil, F; Sanz, P; Prieto, J A

1999-06-01

Bread making is one of the oldest food-manufacturing processes. However, it is only in the past few years that recombinant-DNA technology has led to dramatic changes in formulation, ingredients or processing conditions. New strains of baker's yeast that produce CO2 more rapidly, are more resistant to stress or produce proteins or metabolites that can modify bread flavour, dough rheology or shelf-life are now emerging.

Oxygen-controlled automated neural differentiation of mouse embryonic stem cells.

PubMed

Mondragon-Teran, Paul; Tostoes, Rui; Mason, Chris; Lye, Gary J; Veraitch, Farlan S

2013-03-01

Automation and oxygen tension control are two tools that provide significant improvements to the reproducibility and efficiency of stem cell production processes. the aim of this study was to establish a novel automation platform capable of controlling oxygen tension during both the cell-culture and liquid-handling steps of neural differentiation processes. We built a bespoke automation platform, which enclosed a liquid-handling platform in a sterile, oxygen-controlled environment. An airtight connection was used to transfer cell culture plates to and from an automated oxygen-controlled incubator. Our results demonstrate that our system yielded comparable cell numbers, viabilities, metabolism profiles and differentiation efficiencies when compared with traditional manual processes. Interestingly, eliminating exposure to ambient conditions during the liquid-handling stage resulted in significant improvements in the yield of MAP2-positive neural cells, indicating that this level of control can improve differentiation processes. This article describes, for the first time, an automation platform capable of maintaining oxygen tension control during both the cell-culture and liquid-handling stages of a 2D embryonic stem cell differentiation process.

Effect of medium on friction and wear properties of compacted graphite cast iron processed by biomimetic coupling laser remelting process

NASA Astrophysics Data System (ADS)

Guo, Qing-chun; Zhou, Hong; Wang, Cheng-tao; Zhang, Wei; Lin, Peng-yu; Sun, Na; Ren, Luquan

2009-04-01

Stimulated by the cuticles of soil animals, an attempt to improve the wear resistance of compact graphite cast iron (CGI) with biomimetic units on the surface was made by using a biomimetic coupled laser remelting process in air and various thicknesses water film, respectively. The microstructures of biomimetic units were examined by scanning electron microscope and X-ray diffraction was used to describe the microstructure and identify the phases in the melted zone. Microhardness was measured and the wear behaviors of biomimetic specimens as functions of different mediums as well as various water film thicknesses were investigated under dry sliding condition, respectively. The results indicated that the microstructure zones in the biomimetic specimens processed with water film are refined compared with that processed in air and had better wear resistance increased by 60%, the microhardness of biomimetic units has been improved significantly. The application of water film provided finer microstructures and much more regular grain shape in biomimetic units, which played a key role in improving the friction properties and wear resistance of CGI.

Effects of pelleting conditioner retention time on nursery pig growth performance.

PubMed

Lewis, L L; Stark, C R; Fahrenholz, A C; Goncalves, M A D; DeRouchey, J M; Jones, C K

2015-03-01

A total of 180 nursery pigs (PIC 327 × 1050; initially 12.6 kg) were used in an 18-d study to determine the effects of pellet mill conditioning parameters and feed form on pig performance. All diets were similar, and different feed processing parameters were used to create experimental treatments. Factors considered were conditioning time (15, 30, or 60 s) and feed form (mash or pelleted). To remove the confounding factor of feed form, pelleted samples were reground to a similar particle size as the mash diet. Treatments included: 1) mash diet without thermal processing (negative control), 2) pelleted diet conditioned for 30 s (positive control), 3) pelleted diet conditioned for 15 s and reground, 4) pelleted diet conditioned for 30 s and reground, and 5) pelleted diet conditioned for 60 s and reground. Pigs were weaned and fed a common acclimation diet for 21 d before the start of the experiment. Growth and feed disappearance were then measured for 18 d. All diets had similar levels of percentage total starch, but thermally processed diets had a 1.67 to 1.87-fold increase in percentage gelatinized starch compared to the mash diet. Average daily gain and G:F did not differ between treatments overall, but pigs fed the positive control pelleted diet had decreased ADFI ( < 0.05) compared to pigs fed all other diets. Preplanned contrasts revealed that pigs fed mash diets tended to have greater ADG ( < 0.10) compared to those fed pelleted and reground diets. This suggests that processing may have had a negative influence on feed utilization, which is further supported by the finding that pigs fed mash diets tended to have greater ADG ( < 0.10) compared to those fed diets that were thermally processed, regardless of regrinding. Considering these results, it was not surprising that pigs fed mash diets had greater ADG and ADFI ( < 0.05) than those fed pelleted diets. When directly comparing diets conditioned at 60 rpm, fed either as whole pellets or reground to mash consistency, pigs fed pelleted diets had improved G:F ( < 0.05) due to lower ADFI ( < 0.05) but similar ADG. The expected improvement in G:F from pelleting (6.8%) was observed but lost when diets were reground to near original mash particle size. This may indicate that diet form from the actual pelleting process impacts G:F more than conditioner retention time.

Predictive displays for a process-control schematic interface.

PubMed

Yin, Shanqing; Wickens, Christopher D; Helander, Martin; Laberge, Jason C

2015-02-01

Our objective was to examine the extent to which increasing precision of predictive (rate of change) information in process control will improve performance on a simulated process-control task. Predictive displays have been found to be useful in process control (as well as aviation and maritime industries). However, authors of prior research have not examined the extent to which predictive value is increased by increasing predictor resolution, nor has such research tied potential improvements to changes in process control strategy. Fifty nonprofessional participants each controlled a simulated chemical mixture process (honey mixer simulation) that simulated the operations found in process control. Participants in each of five groups controlled with either no predictor or a predictor ranging in the resolution of prediction of the process. Increasing detail resolution generally increased the benefit of prediction over the control condition although not monotonically so. The best overall performance, combining quality and predictive ability, was obtained by the display of intermediate resolution. The two displays with the lowest resolution were clearly inferior. Predictors with higher resolution are of value but may trade off enhanced sensitivity to variable change (lower-resolution discrete state predictor) with smoother control action (higher-resolution continuous predictors). The research provides guidelines to the process-control industry regarding displays that can most improve operator performance.

Using lean methodology to improve efficiency of electronic order set maintenance in the hospital.

PubMed

Idemoto, Lori; Williams, Barbara; Blackmore, Craig

2016-01-01

Order sets, a series of orders focused around a diagnosis, condition, or treatment, can reinforce best practice, help eliminate outdated practice, and provide clinical guidance. However, order sets require regular updates as evidence and care processes change. We undertook a quality improvement intervention applying lean methodology to create a systematic process for order set review and maintenance. Root cause analysis revealed challenges with unclear prioritization of requests, lack of coordination between teams, and lack of communication between producers and requestors of order sets. In March of 2014, we implemented a systematic, cyclical order set review process, with a set schedule, defined responsibilities for various stakeholders, formal meetings and communication between stakeholders, and transparency of the process. We first identified and deactivated 89 order sets which were infrequently used. Between March and August 2014, 142 order sets went through the new review process. Processing time for the build duration of order sets decreased from a mean of 79.6 to 43.2 days (p<.001, CI=22.1, 50.7). Applying Lean production principles to the order set review process resulted in significant improvement in processing time and increased quality of orders. As use of order sets and other forms of clinical decision support increase, regular evidence and process updates become more critical.

"It's still a great adventure" - exploring offshore employees' working conditions in a qualitative study.

PubMed

Mette, Janika; Velasco Garrido, Marcial; Harth, Volker; Preisser, Alexandra M; Mache, Stefanie

2017-01-01

Despite the particular demands inherent to offshore work, little is known about the working conditions of employees in the German offshore wind industry. To date, neither offshore employees' job demands and resources, nor their needs for improving the working conditions have been explored. Therefore, the aim of this study was to conduct a qualitative analysis to gain further insight into these topics. Forty-two semi-structured telephone interviews with German offshore employees ( n  = 21) and offshore experts ( n  = 21) were conducted. Employees and experts were interviewed with regard to their perceptions of their working conditions offshore. In addition, employees were asked to identify areas with potential need for improvement. The interviews were analysed in a deductive-inductive process according to Mayring's qualitative content analysis. Employees and experts reported various demands of offshore work, including challenging physical labour, long shifts, inactive waiting times, and recurrent absences from home. In contrast, the high personal meaning of the work, regular work schedule (14 days offshore, 14 days onshore), and strong comradeship were highlighted as job resources. Interviewees' working conditions varied considerably, e.g. regarding their work tasks and accommodations. Most of the job demands were perceived in terms of the work organization and living conditions offshore. Likewise, employees expressed the majority of needs for improvement in these areas. Our study offers important insight into the working conditions of employees in the German offshore wind industry. The results can provide a basis for further quantitative research in order to generalize the findings. Moreover, they can be utilized to develop needs-based interventions to improve the working conditions offshore.

Continuous Manufacturing in Pharmaceutical Process Development and Manufacturing.

PubMed

Burcham, Christopher L; Florence, Alastair J; Johnson, Martin D

2018-06-07

The pharmaceutical industry has found new applications for the use of continuous processing for the manufacture of new therapies currently in development. The transformation has been encouraged by regulatory bodies as well as driven by cost reduction, decreased development cycles, access to new chemistries not practical in batch, improved safety, flexible manufacturing platforms, and improved product quality assurance. The transformation from batch to continuous manufacturing processing is the focus of this review. The review is limited to small, chemically synthesized organic molecules and encompasses the manufacture of both active pharmaceutical ingredients (APIs) and the subsequent drug product. Continuous drug product is currently used in approved processes. A few examples of production of APIs under current good manufacturing practice conditions using continuous processing steps have been published in the past five years, but they are lagging behind continuous drug product with respect to regulatory filings.

Understanding plant response to nitrogen limitation for the improvement of crop nitrogen use efficiency.

PubMed

Kant, Surya; Bi, Yong-Mei; Rothstein, Steven J

2011-02-01

Development of genetic varieties with improved nitrogen use efficiency (NUE) is essential for sustainable agriculture. Generally, NUE can be divided into two parts. First, assimilation efficiency involves nitrogen (N) uptake and assimilation and second utilization efficiency involves N remobilization. Understanding the mechanisms regulating these processes is crucial for the improvement of NUE in crop plants. One important approach is to develop an understanding of the plant response to different N regimes, especially to N limitation, using various methods including transcription profiling, analysing mutants defective in their normal response to N limitation, and studying plants that show better growth under N-limiting conditions. One can then attempt to improve NUE in crop plants using the knowledge gained from these studies. There are several potential genetic and molecular approaches for the improvement of crop NUE discussed in this review. Increased knowledge of how plants respond to different N levels as well as to other environmental conditions is required to achieve this.

Physical exercise improves learning in zebrafish, Danio rerio.

PubMed

Luchiari, Ana Carolina; Chacon, Diana Marques Martins

2013-11-01

Zebrafish is an ideal vertebrate model for neuroscience studies focusing on learning and memory. Although genetic manipulation of zebrafish is available, behavioral protocols are often lacking. In this study we tested whether physical activity can facilitate zebrafish's learning process in an associative conditioning task. Learning was inferred by the approach of the feeding area just after the conditioned stimulus (light). Unexercised zebrafish showed conditioning response from the 5th testing day while fish previously submitted to swim against the water current showed learning by the 3rd day of testing. It seems that physical activity may accelerate associative learning response in zebrafish, indicating the benefits of exercise for cognitive processes. We suggest that this preliminary work could be useful for high throughput screening. Copyright © 2013 Elsevier B.V. All rights reserved.

Evidence based position paper on physical and rehabilitation medicine (PRM) professional practice for people with respiratory conditions. The European PRM position (UEMS PRM Section).

PubMed

Oral, Aydan; Juocevicius, Alvydas; Lukmann, Aet; Takáč, Peter; Tederko, Piotr; Hāznere, Ilze; Aguiar-Branco, Catarina; Lazovic, Milica; Negrini, Stefano; Varela Donoso, Enrique; Christodoulou, Nicolas

2018-05-02

Chronic respiratory conditions are among the top causes of death and disability. The aim of the paper is to improve Physical and Rehabilitation Medicine (PRM) physicians' professional practice for persons with chronic respiratory conditions in order to promote their functioning properties and to reduce activity limitations and/or participation restrictions. A systematic review of the literature and a Consensus procedure by means of a Delphi process has been performed involving the delegates of all European countries represented in the UEMS PRM Section. The systematic literature review is reported together with twenty-three recommendations resulting from the Delphi procedure. The professional role of PRM physicians having expertise in the rehabilitation of chronic respiratory conditions is to lead pulmonary rehabilitation programmes in multiprofessional teams, working in collaboration with other disciplines in a variety of settings to improve functioning of people with chronic respiratory conditions. This EBPP represents the official position of the European Union through the UEMS PRM Section and designates the professional role of PRM physicians for people with respiratory conditions.

Evidence based position paper on physical and rehabilitation medicine (PRM) professional practice for people with cardiovascular conditions. The European PRM position (UEMS PRM Section).

PubMed

Juocevicius, Alvydas; Oral, Aydan; Lukmann, Aet; Takáč, Peter; Tederko, Piotr; Hāznere, Ilze; Aguiar-Branco, Catarina; Lazovic, Milica; Negrini, Stefano; Varela Donoso, Enrique; Christodoulou, Nicolas

2018-05-02

Cardiovascular conditions are significant causes of mortality and morbidity leading to substantial disability. The aim of the paper is to improve Physical and Rehabilitation Medicine (PRM) physicians' professional practice for persons with cardiovascular conditions in order to promote their functioning properties and to reduce activity limitations and/or participation restrictions. A systematic review of the literature and a Consensus procedure by means of a Delphi process has been performed involving the delegates of all European countries represented in the UEMS PRM Section. The systematic literature review is reported together with thirty recommendations resulting from the Delphi procedure. The professional role of PRM physicians having expertise in the rehabilitation of cardiovascular conditions is to lead cardiac rehabilitation programmes in multiprofessional teams, working in collaboration with other disciplines in a variety of settings to improve functioning of people with cardiovascular conditions. This EBPP represents the official position of the European Union through the UEMS PRM Section and designates the professional role of PRM physicians in persons with cardiovascular conditions.

Do Research Intermediaries Reduce Perceived Coercion to Enter Research Trials Among Criminally Involved Substance Abusers?

PubMed

Festinger, David S; Dugosh, Karen L; Croft, Jason R; Arabia, Patricia L; Marlowe, Douglas B

2011-01-01

We examined the efficacy of including a research intermediary (RI) during the consent process in reducing participants' perceptions of coercion to enroll in a research study. Eighty-four drug court clients being recruited into an ongoing study were randomized to receive a standard informed consent process alone (standard condition) or with an RI (intermediary condition). Before obtaining consent, RIs met with clients individually to discuss remaining concerns. Findings provided preliminary evidence that RIs reduced client perceptions that their participation might influence how clinical and judicial staff view them. This suggests that using RIs may improve participant autonomy in clinical studies.

Do Research Intermediaries Reduce Perceived Coercion to Enter Research Trials Among Criminally Involved Substance Abusers?

PubMed Central

Festinger, David S.; Dugosh, Karen L.; Croft, Jason R.; Arabia, Patricia L.; Marlowe, Douglas B.

2011-01-01

We examined the efficacy of including a research intermediary (RI) during the consent process in reducing participants’ perceptions of coercion to enroll in a research study. Eighty-four drug court clients being recruited into an ongoing study were randomized to receive a standard informed consent process alone (standard condition) or with an RI (intermediary condition). Before obtaining consent, RIs met with clients individually to discuss remaining concerns. Findings provided preliminary evidence that RIs reduced client perceptions that their participation might influence how clinical and judicial staff view them. This suggests that using RIs may improve participant autonomy in clinical studies. PMID:22081751

Adaptive Wiener filtering for improved acquisition of distortion product otoacoustic emissions.

PubMed

Ozdamar, O; Delgado, R E; Rahman, S; Lopez, C

1998-01-01

An innovative acoustic noise canceling method using adaptive Wiener filtering (AWF) was developed for improved acquisition of distortion product otoacoustic emissions (DPOAEs). The system used one microphone placed in the test ear for the primary signal. Noise reference signals were obtained from three different sources: (a) pre-stimulus response from the test ear microphone, (b) post-stimulus response from a microphone placed near the head of the subject and (c) post-stimulus response obtained from a microphone placed in the subject's nontest ear. In order to improve spectral estimation, block averaging of a different number of single sweep responses was used. DPOAE data were obtained from 11 ears of healthy newborns in a well-baby nursery of a hospital under typical noise conditions. Simultaneously obtained recordings from all three microphones were digitized, stored and processed off-line to evaluate the effects of AWF with respect to DPOAE detection and signal-to-noise ratio (SNR) improvement. Results show that compared to standard DPOAE processing, AWF improved signal detection and improved SNR.

Haiti: Two Decades of Intervention and Very Little to Show

DTIC Science & Technology

2012-05-17

the period 1994 to 2010, from Operation Uphold Democracy to the Leogane earthquake, with the hope that the research would help improve US policy or...while the guidance given to JTF-180 throughout the planning process provided the strategic aims. UN Security Council Resolutions beginning with...the intervention. If the objectives of the intervention did not include an attempt to improve those conditions in Haiti, then the objectives were

High performance cryogenic turboexpanders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agahi, R.R.; Ershaghi, B.; Lin, M.C.

1996-12-31

The use of turboexpanders for deep cryogenic temperatures has been constrained because of thermal efficiency limitations. This limited thermal efficiency was mostly due to mechanical constraints. Recent improvements in analytical techniques, bearing technology, and design features have made it possible to design and operate turboexpanders at more favorable conditions, such as of higher rotational speeds. Several turboexpander installations in helium and hydrogen processes have shown a significant improvement in plant performance over non-turboexpander options.

Using mixed inocula of Saccharomyces cerevisiae killer strains to improve the quality of traditional sparkling-wine.

PubMed

Velázquez, Rocío; Zamora, Emiliano; Álvarez, Manuel; Álvarez, María L; Ramírez, Manuel

2016-10-01

The quality of traditional sparkling-wine depends on the aging process in the presence of dead yeast cells. These cells undergo a slow autolysis process thereby releasing some compounds, mostly colloidal polymers such as polysaccharides and mannoproteins, which influence the wine's foam properties and mouthfeel. Saccharomyces cerevisiae killer yeasts were tested to increase cell death and autolysis during mixed-yeast-inoculated second fermentation and aging. These yeasts killed sensitive strains in killer plate assays done under conditions of low pH and temperature similar to those used in sparkling-wine making, although some strains showed a different killer behaviour during the second fermentation. The fast killer effect improved the foam quality and mouthfeel of the mixed-inoculated wines, while the slow killer effect gave small improvements over single-inoculated wines. The effect was faster under high-pressure than under low-pressure conditions. Wine quality improvement did not correlate with the polysaccharide, protein, mannan, or aromatic compound concentrations, suggesting that the mouthfeel and foaming quality of sparkling wine are very complex properties influenced by other wine compounds and their interactions, as well as probably by the specific chemical composition of a given wine. Copyright © 2016 Elsevier Ltd. All rights reserved.

Single-Sided Deafness: Impact of Cochlear Implantation on Speech Perception in Complex Noise and on Auditory Localization Accuracy.

PubMed

Döge, Julia; Baumann, Uwe; Weissgerber, Tobias; Rader, Tobias

2017-12-01

To assess auditory localization accuracy and speech reception threshold (SRT) in complex noise conditions in adult patients with acquired single-sided deafness, after intervention with a cochlear implant (CI) in the deaf ear. Nonrandomized, open, prospective patient series. Tertiary referral university hospital. Eleven patients with late-onset single-sided deafness (SSD) and normal hearing in the unaffected ear, who received a CI. All patients were experienced CI users. Unilateral cochlear implantation. Speech perception was tested in a complex multitalker equivalent noise field consisting of multiple sound sources. Speech reception thresholds in noise were determined in aided (with CI) and unaided conditions. Localization accuracy was assessed in complete darkness. Acoustic stimuli were radiated by multiple loudspeakers distributed in the frontal horizontal plane between -60 and +60 degrees. In the aided condition, results show slightly improved speech reception scores compared with the unaided condition in most of the patients. For 8 of the 11 subjects, SRT was improved between 0.37 and 1.70 dB. Three of the 11 subjects showed deteriorations between 1.22 and 3.24 dB SRT. Median localization error decreased significantly by 12.9 degrees compared with the unaided condition. CI in single-sided deafness is an effective treatment to improve the auditory localization accuracy. Speech reception in complex noise conditions is improved to a lesser extent in 73% of the participating CI SSD patients. However, the absence of true binaural interaction effects (summation, squelch) impedes further improvements. The development of speech processing strategies that respect binaural interaction seems to be mandatory to advance speech perception in demanding listening situations in SSD patients.

Preparation and Physicochemical Properties of Vinblastine Microparticles by Supercritical Antisolvent Process

PubMed Central

Zhang, Xiaonan; Zhao, Xiuhua; Zu, Yuangang; Chen, Xiaoqiang; Lu, Qi; Ma, Yuliang; Yang, Lei

2012-01-01

The objective of the study was to prepare vinblastine microparticles by supercritical antisolvent process using N-methyl-2-pyrrolidone as solvent and carbon dioxide as antisolvent and evaluate its physicochemical properties. The effects of four process variables, pressure, temperature, drug concentration and drug solution flow rate, on drug particle formation during the supercritical antisolvent process, were investigated. Particles with a mean particle size of 121 ± 5.3 nm were obtained under the optimized process conditions (precipitation temperature 60 °C, precipitation pressure 25 MPa, vinblastine concentration 2.50 mg/mL and vinblastine solution flow rate 6.7 mL/min). The vinblastine was characterized by scanning electron microscopy, X-ray diffraction, Fourier-transform infrared spectroscopy, mass spectrometry and dissolution test. It was concluded that physicochemical properties of crystalline vinblastine could be improved by physical modification, such as particle size reduction and generation of amorphous state using the supercritical antisolvent process. Furthermore, the supercritical antisolvent process was a powerful methodology for improving the physicochemical properties of vinblastine. PMID:23202916

Behavior and structure of metal vapor arc plasma between molten electrodes

NASA Astrophysics Data System (ADS)

Zanner, F. J.; Williamson, R. L.; Hareland, W. A.; Bertram, L. A.

A metal vapor arc is utilized in the industrially important vacuum arc remelting (VAR) process to produce materials by melting and resolidification which have improved structure and chemical homogeneity. Homogeneity is dependent on achieving quasi-steady conditions in the plasma because of its thermal and MHD coupling with the molten pool atop the ingot. Optimal operating conditions of low pressure (approx. = 0.01 torr) and short electrode gap (less than 15 mm) produce a diffuse arc and cathode spot behavior similar to that observed for the vacuum breaker arc. Under these conditions the arc provides a quasi-steady heat source that is considered to be the bench mark arc of the VAR process. Previous work has shown that deviation from the bench mark arc behavior can occur under production conditions, and is caused by electrode irregularities and liberation of gases such as CO from the molten pool. This study is an effort to characterize these behavioral deviations and discover operational conditions which stabilize the bench mark arc.

Effects of operational conditions on sludge degradation and organic acids formation in low-critical wet air oxidation.

PubMed

Chung, Jinwook; Lee, Mikyung; Ahn, Jaehwan; Bae, Wookeun; Lee, Yong-Woo; Shim, Hojae

2009-02-15

Wet air oxidation processes are to treat highly concentrated organic compounds including refractory materials, sludge, and night soil, and usually operated at supercritical water conditions of high temperature and pressure. In this study, the effects of operational conditions including temperature, pressure, and oxidant dose on sludge degradation and conversion into subsequent intermediates such as organic acids were investigated at low critical wet oxidation conditions. The reaction time and temperature in the wet air oxidation process was shown an important factor affecting the liquefaction of volatile solids, with more significant effect on the thermal hydrolysis reaction rather than the oxidation reaction. The degradation efficiency of sludge and the formation of organic acids were improved with longer reaction time and higher reaction temperature. For the sludge reduction and the organic acids formation under the wet air oxidation, the optimal conditions for reaction temperature, time, pressure, and oxidant dose were shown approximately 240 degrees C, 30min, 60atm, and 2.0L/min, respectively.

The ANAMMOX reactor under transient-state conditions: process stability with fluctuations of the nitrogen concentration, inflow rate, pH and sodium chloride addition.

PubMed

Yu, Jin-Jin; Jin, Ren-Cun

2012-09-01

The process stability of an anaerobic ammonium oxidation (ANAMMOX) was investigated in an upflow anaerobic sludge blanket reactor subjected to overloads of 2.0- to 3.0-fold increases in substrate concentrations, inflow rates lasting 12 or 24h, extreme pH levels of 4 and 10 for 12h and a 12-h 30 g l(-1) NaCl addition. During the overloads, the nitrogen removal rate improved, and the shock period was an important factor affecting the reactor performance. In the high pH condition, the reactor performance significantly degenerated; while in the low pH condition, it did not happen. The NaCl addition caused the most serious deterioration in the reactor, which took 108 h to recover and was accompanied by a stoichiometric ratio divergence. There are well correlations between the total nitrogen and the electrical conductivity which is considered to be a convenient signal for controlling and monitoring the ANAMMOX process under transient-state conditions. Copyright © 2012 Elsevier Ltd. All rights reserved.

Oxygen Transfer in Moving Bed Biofilm Reactor and Integrated Fixed Film Activated Sludge Processes.

PubMed

2017-11-17

A demonstrated approach to design the, so-called, medium-bubble air diffusion network for oxygen transfer into the aerobic zone(s) of moving bed biofilm reactor (MBBR) and integrated fixed-film activated sludge (IFAS) processes is described in this paper. Operational full-scale biological water resource recovery systems treating municipal sewerage demonstrate that medium-bubble air diffusion networks designed using the method presented here provide reliable service. Further improvement is possible, however, as knowledge gaps prevent more rational process designs. Filling such knowledge gaps can potentially result in higher performing and more economical systems. Small-scale system testing demonstrates significant enhancement of oxygen transfer capacity due to the presence of media, but quantification of such effects in full-scale systems is lacking, and is needed. Establishment of the relationship between diffuser submergence, aeration rate, and biofilm carrier fill fraction will enhance MBBR and IFAS aerobic process design, cost, and performance. Limited testing of full-scale systems is available to allow computation of alpha valuess. As with clean water testing of full-scale systems, further full-scale testing under actual operating conditions is required to more fully quantify MBBR and IFAS system oxygen transfer performance under a wide range of operating conditions. Control of MBBR and IFAS aerobic zone oxygen transfer systems can be optimized by recognizing that varying residual dissolved oxygen (DO) concentrations are needed, depending on operating conditions. For example, the DO concentration in the aerobic zone of nitrifying IFAS processes can be lowered during warm weather conditions when greater suspended growth nitrification can occur, resulting in the need for reduced nitrification by the biofilm compartment. Further application of oxygen transfer control approaches used in activated sludge systems to MBBR and IFAS systems, such as ammonia-based oxygen transfer system control, has been demonstrated to further improve MBBR and IFAS system energy-efficiency.

Investigation of a lithium-halogen exchange flow process for the preparation of boronates by using a cryo-flow reactor.

PubMed

Newby, James A; Huck, Lena; Blaylock, D Wayne; Witt, Paul M; Ley, Steven V; Browne, Duncan L

2014-01-03

Conducting low-temperature organometallic reactions under continuous flow conditions offers the potential to more accurately control exotherms and thus provide more reproducible and scalable processes. Herein, progress towards this goal with regards to the lithium-halogen exchange/borylation reaction is reported. In addition to improving the scope of substrates available on a research scale, methods to improve reaction profiles and expedite purification of the products are also described. On moving to a continuous system, thermocouple measurements have been used to track exotherms and provide a level of safety for continuous processing of organometallic reagents. The use of an in-line continuous liquid-liquid separation device to circumvent labour intensive downstream off-line processing is also reported. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Complex automatic data processing in multi-profile hospitals].

PubMed

Dovzhenko, Iu M; Panov, G D

1990-01-01

The computerization of data processing in multi-disciplinary hospitals is the key factor in raising the quality of medical care provided to the population, intensifying the work of the personnel, improving the curative and diagnostic process and the use of resources. Even a small experience in complex computerization at the Botkin Hospital indicates that due to the use of the automated system the quality of data processing in being improved, a high level of patients' examination is being provided, a speedy training of young specialists is being achieved, conditions are being created for continuing education of physicians through the analysis of their own activity. At big hospitals a complex solution of administrative and curative diagnostic tasks on the basis of general hospital network of display connection and general hospital data bank is the most prospective form of computerization.

Liquefaction Of Coal With Surfactant And Disposable Catalyst

NASA Technical Reports Server (NTRS)

Hickey, Gregory S.; Sharma, Pramod K.

1996-01-01

Fuels derived from coal more competitive with petroleum products. Improved coal-liquefaction process exploits synergistic effects of disposable iron oxide catalyst and cheap anionic surfactant. Efficiency of conversion achieved in significantly higher than efficiencies obtained with addition of either surfactant or catalyst alone. No costly pretreatment necessary, and increase in conversion achieved under processing conditions milder than those used heretofore in liquefaction of coal. Quality of distillates obtained after liquefaction in process expected superior to distillates obtained after liquefaction by older techniques.

Transpiration rates of rice plants treated with Trichoderma spp.

NASA Astrophysics Data System (ADS)

Doni, Febri; Anizan, I.; Che Radziah C. M., Z.; Yusoff, Wan Mohtar Wan

2014-09-01

Trichoderma spp. are considered as successful plant growth promoting fungi and have positive role in habitat engineering. In this study, the potential for Trichoderma spp. to regulate transpiration process in rice plant was assessed experimentally under greenhouse condition using a completely randomized design. The study revealed that Trichoderma spp. have potential to enhance growth of rice plant through transpirational processes. The results of the study add to the advancement of the understanding as to the role of Trichoderma spp. in improving rice physiological process.

[Quality improvement potential in the pharmaceutical industry].

PubMed

Nusser, Michael

2007-01-01

The performance of the German pharmaceutical industry, future challenges and obstacles to quality improvement are assessed from a systems-of-innovation perspective, using appropriate innovation indicators. The current close-to-market performance indicators paint an unfavourable picture. Early R&D indicators (e.g., publications, patents), however, reveal a positive trend. A lot of obstacles to quality improvements are identified with respect to knowledge base, knowledge/technology transfer, industrial R&D processes, capital markets, market attractiveness and both regulatory and political framework conditions. On this basis, recommendations will finally be derived to improve quality in the pharmaceutical industry.

Adaptation to high throughput batch chromatography enhances multivariate screening.

PubMed

Barker, Gregory A; Calzada, Joseph; Herzer, Sibylle; Rieble, Siegfried

2015-09-01

High throughput process development offers unique approaches to explore complex process design spaces with relatively low material consumption. Batch chromatography is one technique that can be used to screen chromatographic conditions in a 96-well plate. Typical batch chromatography workflows examine variations in buffer conditions or comparison of multiple resins in a given process, as opposed to the assessment of protein loading conditions in combination with other factors. A modification to the batch chromatography paradigm is described here where experimental planning, programming, and a staggered loading approach increase the multivariate space that can be explored with a liquid handling system. The iterative batch chromatography (IBC) approach is described, which treats every well in a 96-well plate as an individual experiment, wherein protein loading conditions can be varied alongside other factors such as wash and elution buffer conditions. As all of these factors are explored in the same experiment, the interactions between them are characterized and the number of follow-up confirmatory experiments is reduced. This in turn improves statistical power and throughput. Two examples of the IBC method are shown and the impact of the load conditions are assessed in combination with the other factors explored. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Precursors in the preparation of transition metal nitrides and transition metal carbonitrides and their reaction intermediates

DOEpatents

Maya, Leon

1991-01-01

A process for making ammonolytic precursors to nitride and carbonitride ceramics. Extreme reaction conditions are not required and the precursor is a powder-like substance that produces ceramics of improved purity and morphology upon pyrolysis.

Meniscus Imaging for Crystal-Growth Control

NASA Technical Reports Server (NTRS)

Sachs, E. M.

1983-01-01

Silicon crystal growth monitored by new video system reduces operator stress and improves conditions for observation and control of growing process. System optics produce greater magnification vertically than horizontally, so entire meniscus and melt is viewed with high resolution in both width and height dimensions.

Final Exam.

ERIC Educational Resources Information Center

Coullahan, Richard

1998-01-01

Explains the use of a maintenance-management assessment process that educational facility managers can use to improve facility conditions and to provide evidence for future capital investments in maintenance management. Discusses questions a maintenance-management audit can answer and describes how to analyze the data to gain maximum understanding…

77 FR 23283 - Tribal Consultation Policy

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-18

... and Waivers VII. Consultation Process Guidelines VIII. Performance and Accountability IX. Designated..., improving working conditions, and assuring work-related benefits and rights of workers and retirees in the... services. The Department's Women's Bureau (WB) has an ongoing relationship with the United Indians of All...

Rapid thermal annealing of CH 3 NH 3 PbI 3 perovskite thin films by intense pulsed light with aid of diiodomethane additive

DOE PAGES

Ankireddy, Krishnamraju; Ghahremani, Amir H.; Martin, Blake; ...

2018-01-01

Perovskite thin films are thermally annealed using a rapid intense pulsed light technique enabled by an alkyl halide that collectively improves device performance when processed in ambient conditions.

On the use of continuous flash suppression for the study of visual processing outside of awareness

PubMed Central

Yang, Eunice; Brascamp, Jan; Kang, Min-Suk; Blake, Randolph

2014-01-01

The interocular suppression technique termed continuous flash suppression (CFS) has become an immensely popular tool for investigating visual processing outside of awareness. The emerging picture from studies using CFS is that extensive processing of a visual stimulus, including its semantic and affective content, occurs despite suppression from awareness of that stimulus by CFS. However, the current implementation of CFS in many studies examining processing outside of awareness has several drawbacks that may be improved upon for future studies using CFS. In this paper, we address some of those shortcomings, particularly ones that affect the assessment of unawareness during CFS, and ones to do with the use of “visible” conditions that are often included as a comparison to a CFS condition. We also discuss potential biases in stimulus processing as a result of spatial attention and feature-selective suppression. We suggest practical guidelines that minimize the effects of those limitations in using CFS to study visual processing outside of awareness. PMID:25071685

Staying Well in a Sea of Harm.

PubMed

Deutsch, Ellen S

2018-03-01

Physician psychological wellness is an emergent outcome resulting from dynamic interactions among complex conditions. We may enhance opportunities for physician wellness by applying principles developed to improve another emergent outcome: patient safety. The Safety I approach to patient safety focuses on "what went wrong" and considers humans a liability. Safety II is a powerful complementary approach that focuses on "what went right" and values human creativity. These contrasting perspectives are described in the context of patient safety, but the underlying principles have relevance for physician psychological wellness. We can create conditions that interfere with wellness and conditions that support wellness. We can learn from exploring and reinforcing successes and improving routine processes; together, these approaches may have a greater cumulative positive impact than just addressing problems. In addition to learning from failures, there is much we can learn from success.

Modern methods of surveyor observations in opencast mining under complex hydrogeological conditions.

NASA Astrophysics Data System (ADS)

Usoltseva, L. A.; Lushpei, V. P.; Mursin, VA

2017-10-01

The article considers the possibility of linking the modern methods of surveying security of open mining works to improve industrial safety in the Primorsky Territory, as well as their use in the educational process. Industrial Safety in the management of Surface Mining depends largely on the applied assessment methods and methods of stability of pit walls and slopes of dumps in the complex mining and hydro-geological conditions.

Does manipulating the speed of visual flow in virtual reality change distance estimation while walking in Parkinson's disease?

PubMed

Ehgoetz Martens, Kaylena A; Ellard, Colin G; Almeida, Quincy J

2015-03-01

Although dopaminergic replacement therapy is believed to improve sensory processing in PD, while delayed perceptual speed is thought to be caused by a predominantly cholinergic deficit, it is unclear whether sensory-perceptual deficits are a result of corrupt sensory processing, or a delay in updating perceived feedback during movement. The current study aimed to examine these two hypotheses by manipulating visual flow speed and dopaminergic medication to examine which influenced distance estimation in PD. Fourteen PD and sixteen HC participants were instructed to estimate the distance of a remembered target by walking to the position the target formerly occupied. This task was completed in virtual reality in order to manipulate the visual flow (VF) speed in real time. Three conditions were carried out: (1) BASELINE: VF speed was equal to participants' real-time movement speed; (2) SLOW: VF speed was reduced by 50 %; (2) FAST: VF speed was increased by 30 %. Individuals with PD performed the experiment in their ON and OFF state. PD demonstrated significantly greater judgement error during BASELINE and FAST conditions compared to HC, although PD did not improve their judgement error during the SLOW condition. Additionally, PD had greater variable error during baseline compared to HC; however, during the SLOW conditions, PD had significantly less variable error compared to baseline and similar variable error to HC participants. Overall, dopaminergic medication did not significantly influence judgement error. Therefore, these results suggest that corrupt processing of sensory information is the main contributor to sensory-perceptual deficits during movement in PD rather than delayed updating of sensory feedback.

Cyber-physical system for a water reclamation plant: Balancing aeration, energy, and water quality to maintain process resilience

NASA Astrophysics Data System (ADS)

Zhu, Junjie

Aeration accounts for a large fraction of energy consumption in conventional water reclamation plants (WRPs). Although process operations at older WRPs can satisfy effluent permit requirements, they typically operate with excess aeration. More effective process controls at older WRPs can be challenging as operators work to balance higher energy costs and more stringent effluent limitations while managing fluctuating loads. Therefore, understandings of process resilience or ability to quickly return to original operation conditions at a WRP are important. A state-of-art WRP should maintain process resilience to deal with different kinds of perturbations even after optimization of energy demands. This work was to evaluate the applicability and feasibility of cyber-physical system (CPS) for improving operation at Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) Calumet WRP. In this work, a process model was developed and used to better understand the conditions of current Calumet WRP, with additional valuable information from two dissolved oxygen field measurements. Meanwhile, a classification system was developed to reveal the pattern of historical influent scenario based on cluster analysis and cross-tabulation analysis. Based on the results from the classification, typical process control options were investigated. To ensure the feasibility of information acquisition, the reliability and flexibility of soft sensors were assessed to typical influent conditions. Finally, the process resilience was investigated to better balance influent perturbations, energy demands, and effluent quality for long-term operations. These investigations and evaluations show that although the energy demands change as the influent conditions and process controls. In general, aeration savings could be up to 50% from the level of current consumption; with a more complex process controls, the saving could be up to 70% in relatively steady-state conditions and at least 40% in relatively challenging transient conditions. The soft sensors can provide reliable and flexible performance on target predictions. The plant can still maintain at a similar level of process resilience after 50% aeration saving, even during long-term perturbations. Overall, this work shows that it is well feasible to provide more cost-effective operations at the Calumet WRP, and meanwhile influent perturbations, effluent quality, and process resilience are well in balance.

Improving Processes of Mechanized Pulsed Arc Welding of Low-Frequency Range Variation of Mode Parameters

NASA Astrophysics Data System (ADS)

Saraev, Yu N.; Solodskiy, S. A.; Ulyanova, O. V.

2016-04-01

A new technology of low-frequency modulation of the arc current in MAG and MIG welding is presented. The technology provides control of thermal and crystallization processes, stabilizes the time of formation and crystallization of the weld pool. Conducting theoretical studies allowed formulating the basic criteria for obtaining strong permanent joints for high-duty structures, providing conditions for more equilibrium structure of the deposited metal and the smaller width of the HAZ. The stabilization of time of the formation and crystallization of the weld pool improves the formation of the weld and increases productivity in welding thin sheet metal.

The effect of texture and grain size on improving the mechanical properties of Mg-Al-Zn alloys by friction stir processing.

PubMed

Peng, Jinhua; Zhang, Zhen; Liu, Zhao; Li, Yaozu; Guo, Peng; Zhou, Wei; Wu, Yucheng

2018-03-08

Friction stir processing (FSP) was used to achieve grain refinement on Mg-Al-Zn alloys, which also brought in significant texture modification. The different micro-texture characteristics were found to cause irregular micro-hardness distribution in FSPed region. The effects of texture and grain size were investigated by comparative analyses with strongly textured rolling sheet. Grain refinement improved both strength and elongation in condition of a basal texture while such led to an increment in yield stress and a drop in elongation and ultimate stress when the basal texture was modified by FSP.

Heat transfer mechanisms in poplar wood undergoing torrefaction

NASA Astrophysics Data System (ADS)

Sule, Idris O.; Mahmud, Shohel; Dutta, Animesh; Tasnim, Syeda Humaira

2016-03-01

Torrefaction, a thermal treatment process of biomass, has been proved to improve biomass combustible properties. Torrefaction is defined as a thermochemical process in reduced oxygen condition and at temperature range from 200 to 300 °C for shorter residence time whereby energy yield is maximized, can be a bridging technology that can lead the conventional system (e.g. coal-fired plants) towards a sustainable energy system. In efforts to develop a commercial operable torrefaction reactor, the present study examines the minimum input condition at which biomass is torrefied and explores the heat transfer mechanisms during torrefaction in poplar wood samples. The heat transfer through the wood sample is numerically modeled and analyzed. Each poplar wood is torrefied at temperature of 250, 270, and 300 °C. The experimental study shows that the 270 °C-treatment can be deduced as the optimal input condition for torrefaction of poplar wood. A good understanding of heat transfer mechanisms can facilitate the upscaling and downscaling of torrefaction process equipment to fit the feedstock input criteria and can help to develop treatment input specifications that can maximize process efficiency.

Effect of additive solutions on red blood cell (RBC) membrane properties of stored RBCs prepared from whole blood held for 24 hours at room temperature.

PubMed

Veale, Margaret F; Healey, Gerry; Sparrow, Rosemary L

2011-01-01

The quality of RBC components is influenced by collection, processing and storage conditions. Regulations require that whole blood (WB) units be refrigerated within 8 hours and processed into RBCs within 24 hours of collection. Overnight room temperature hold of WB has logistical advantages, but the effect on RBC quality has not been fully investigated. RBC additive solutions were compared for their ability to provide improved quality of RBCs prepared from WB held at room temperature for 24 hours. Leukocyte-reduced RBCs were prepared from WB held at 20°C on cooling plates for 24 hours prior to processing. RBCs were stored in additive solutions, SAG-M (control), Erythrosol-4, and PAGGSM, under standard blood banking conditions and sampled during 49 days of storage. Stored RBCs were evaluated for RBC shape and microparticle (MP) accumulation using flow cytometry. Osmotic fragility, adhesion of RBCs to endothelium under shear stress conditions (0.5 dyne/cm(2) ), and routine RBC quality parameters were assessed. RBCs stored in Erythrosol-4 and PAGGSM had decreased cell size, reduced osmotic fragility, and decreased accumulation of glycophorin A-positive MPs and annexin V-binding MPs compared with RBCs stored in SAG-M. RBCs stored in erythrosol-4 had increased adherence to endothelium at days 42 and 49 compared with RBCs stored in SAG-M or PAGGSM. RBCs stored in PAGGSM or Erythrosol-4 had improved retention of RBC membrane and osmotic resilience. The development of new additive solutions may offer improved quality of RBC components prepared from WB held overnight at room temperature. © 2010 American Association of Blood Banks.

Does Guiding Toward Task-Relevant Information Help Improve Graph Processing and Graph Comprehension of Individuals with Low or High Numeracy? An Eye-Tracker Experiment.

PubMed

Keller, Carmen; Junghans, Alex

2017-11-01

Individuals with low numeracy have difficulties with understanding complex graphs. Combining the information-processing approach to numeracy with graph comprehension and information-reduction theories, we examined whether high numerates' better comprehension might be explained by their closer attention to task-relevant graphical elements, from which they would expect numerical information to understand the graph. Furthermore, we investigated whether participants could be trained in improving their attention to task-relevant information and graph comprehension. In an eye-tracker experiment ( N = 110) involving a sample from the general population, we presented participants with 2 hypothetical scenarios (stomach cancer, leukemia) showing survival curves for 2 treatments. In the training condition, participants received written instructions on how to read the graph. In the control condition, participants received another text. We tracked participants' eye movements while they answered 9 knowledge questions. The sum constituted graph comprehension. We analyzed visual attention to task-relevant graphical elements by using relative fixation durations and relative fixation counts. The mediation analysis revealed a significant ( P < 0.05) indirect effect of numeracy on graph comprehension through visual attention to task-relevant information, which did not differ between the 2 conditions. Training had a significant main effect on visual attention ( P < 0.05) but not on graph comprehension ( P < 0.07). Individuals with high numeracy have better graph comprehension due to their greater attention to task-relevant graphical elements than individuals with low numeracy. With appropriate instructions, both groups can be trained to improve their graph-processing efficiency. Future research should examine (e.g., motivational) mediators between visual attention and graph comprehension to develop appropriate instructions that also result in higher graph comprehension.

Improved C/SiC Ceramic Composites Made Using PIP

NASA Technical Reports Server (NTRS)

Easler, Timothy

2007-01-01

Improved carbon-fiber-reinforced SiC ceramic-matrix composite (C/SiC CMC) materials, suitable for fabrication of thick-section structural components, are producible by use of a combination of raw materials and processing conditions different from such combinations used in the prior art. In comparison with prior C/SiC CMC materials, these materials have more nearly uniform density, less porosity, and greater strength. The majority of raw-material/processing-condition combinations used in the prior art involve the use of chemical vapor infiltration (CVI) for densifying the matrix. In contrast, in synthesizing a material of the present type, one uses a combination of infiltration with, and pyrolysis of, a preceramic polymer [polymer infiltration followed by pyrolysis (PIP)]. PIP processing is performed in repeated, tailored cycles of infiltration followed by pyrolysis. Densification by PIP processing takes less time and costs less than does densification by CVI. When one of these improved materials was tested by exposure to a high-temperature, inert-gas environment that caused prior C/SiC CMCs to lose strength, this material did not lose strength. (Information on the temperature and exposure time was not available at the time of writing this article.) A material of the present improved type consists, more specifically, of (1) carbon fibers coated with an engineered fiber/matrix interface material and (2) a ceramic matrix, containing SiC, derived from a pre-ceramic polymer with ceramic powder additions. The enhancements of properties of these materials relative to those of prior C/SiC CMC materials are attributable largely to engineering of the fiber/ matrix interfacial material and the densification process. The synthesis of a material of this type includes processing at an elevated temperature to a low level of open porosity. The approach followed in this processing allows one to fabricate not only simple plates but also more complexly shaped parts. The carbon fiber reinforcement in a material of this type can be in any of several alternative forms, including tow, fabric, or complex preforms containing fibers oriented in multiple directions.

Improved extraction of avocado oil by application of sono-physical processes.

PubMed

Martínez-Padilla, Laura Patricia; Franke, Lisa; Xu, Xin-Qing; Juliano, Pablo

2018-01-01

Ultrasound treatment is known to increase the oil extractability in olive and palm oil processes. This work examined the effect of ultrasound conditioning of avocado puree on oil extractability and quality, at low (18+40kHz) and high (2MHz) frequencies, at litre-scale. Other ultrasound parameters evaluated included high frequency effect (0.4, 0.6, and 2MHz; 5min; 90kJ/kg) and sonication time (2.5-10min at 2MHz), without malaxation. Finally, a megasonic post-malaxation intervention was assessed at selected malaxation times (15, 30, and 60min). Both low and high frequency ultrasound treatments of the non-malaxed avocado puree improved extractability by 15-24% additional oil recovery, with the highest extractability achieved after 2MHz treatments, depending on the fruit maturity and oil content. There was no preferential improvement on oil extractability observed across high frequencies, even though extractability increased with sonication time. Ultrasound treatment also showed a positive effect after puree malaxation. Oils obtained from sonicated purees showed peroxide and free fatty acid values below the industrial specification levels and an increase in total phenolic compounds after 2MHz treatment. High frequency ultrasound conditioning of avocado puree can enhance oil separation and potentially decrease the malaxation time in industrial processes without impacting on oil quality. Copyright © 2017 Elsevier B.V. All rights reserved.

Cryo-comminution of plastic waste.

PubMed

Gente, Vincenzo; La Marca, Floriana; Lucci, Federica; Massacci, Paolo; Pani, Eleonora

2004-01-01

Recycling of plastics is a big issue in terms of environmental sustainability and of waste management. The development of proper technologies for plastic recycling is recognised as a priority. To achieve this aim, the technologies applied in mineral processing can be adapted to recycling systems. In particular, the improvement of comminution technologies is one of the main actions to improve the quality of recycled plastics. The aim of this work is to point out suitable comminution processes for different types of plastic waste. Laboratory comminution tests have been carried out under different conditions of temperature and sample pre-conditioning adopting as refrigerant agents CO2 and liquid nitrogen. The temperature has been monitored by thermocouples placed in the milling chamber. Also different internal mill screens have been adopted. A proper procedure has been set up in order to obtain a selective comminution and a size reduction suitable for further separation treatment. Tests have been performed on plastics coming from medical plastic waste and from a plant for spent lead batteries recycling. Results coming from different mill devices have been compared taking into consideration different indexes for representative size distributions. The results of the performed tests show as cryo-comminution improves the effectiveness of size reduction of plastics, promotes liberation of constituents and increases specific surface size of comminuted particles in comparison to a comminution process carried out at room temperature. Copyright 2004 Elsevier Ltd.

A case study employing operant conditioning to reduce stress of capture for red-bellied tamarins (Saguinus labiatus).

PubMed

Owen, Yvonne; Amory, Jonathan R

2011-01-01

Traditional techniques used to capture New World monkeys, such as net capture, can induce high levels of acute stress detrimental to welfare. Alternatively, training nonhuman animals via operant conditioning to voluntarily participate in husbandry and/or veterinary practices is accepted as a humane process that can reduce stress and improve welfare. This study details the use of operant conditioning using positive reinforcement training (PRT) and target training to train a family of 5 captive red-bellied tamarins (Saguinus labiatus) in a wildlife park to voluntarily enter a transportation box and remain calm for 1 min after 54 training sessions. Observations of 2 unrelated net-capture processes provided measures of locomotion and vocalizations as indicators of stress behavior that were compared with those of the trained tamarins. Net-captured monkeys exhibited rapid erratic locomotion and emitted long, high-frequency vocalizations during capture whereas the trained tamarins exhibited minimal locomotion and emitted only 4 brief vocalizations (root mean square 35 dB) during capture. This indicates that the use of PRT considerably reduced potential for stress and improved welfare during the capture and containment of the tamarins. Copyright © Taylor & Francis Group, LLC

Extinction learning in childhood anxiety disorders, obsessive compulsive disorder and posttraumatic stress disorder: implications for treatment

PubMed Central

McGuire, Joseph F.; Orr, Scott P.; Essoe, Joey K.-Y.; McCracken, James T.; Storch, Eric A.; Piacentini, John

2018-01-01

Introduction Threat conditioning and extinction play an important role in anxiety disorders, obsessive compulsive disorder (OCD), and posttraumatic stress disorder (PTSD). Although these conditions commonly affect children, threat conditioning and extinction have been primarily studied in adults. However, differences in phenomenology and neural architecture prohibit the generalization of adult findings to youth. Areas covered A comprehensive literature search using PubMed and PsycInfo was conducted to identify studies that have used differential conditioning tasks to examine threat acquisition and extinction in youth. The information obtained from this review helps to clarify the influence of these processes on the etiology and treatment of youth with OCD, PTSD and other anxiety disorders. Thirty studies of threat conditioning and extinction were identified. Expert Commentary Youth with anxiety disorders, OCD, and PTSD have largely comparable threat acquisition relative to unaffected controls, with some distinctions noted for youth with PTSD or youth who have suffered maltreatment. However, impaired extinction was consistently observed across youth with these disorders and appears to be consistent with deficiencies in inhibitory learning. Incorporating strategies to improve inhibitory learning may improve extinction learning within extinction-based treatments like cognitive behavioral therapy (CBT). Strategies to improve inhibitory learning in CBT are discussed. PMID:27275519

Extinction learning in childhood anxiety disorders, obsessive compulsive disorder and post-traumatic stress disorder: implications for treatment.

PubMed

McGuire, Joseph F; Orr, Scott P; Essoe, Joey K-Y; McCracken, James T; Storch, Eric A; Piacentini, John

2016-10-01

Threat conditioning and extinction play an important role in anxiety disorders, obsessive compulsive disorder (OCD), and post-traumatic stress disorder (PTSD). Although these conditions commonly affect children, threat conditioning and extinction have been primarily studied in adults. However, differences in phenomenology and neural architecture prohibit the generalization of adult findings to youth. A comprehensive literature search using PubMed and PsycInfo was conducted to identify studies that have used differential conditioning tasks to examine threat acquisition and extinction in youth. The information obtained from this review helps to clarify the influence of these processes on the etiology and treatment of youth with OCD, PTSD and other anxiety disorders. Thirty studies of threat conditioning and extinction were identified Expert commentary: Youth with anxiety disorders, OCD, and PTSD have largely comparable threat acquisition relative to unaffected controls, with some distinctions noted for youth with PTSD or youth who have suffered maltreatment. However, impaired extinction was consistently observed across youth with these disorders and appears to be consistent with deficiencies in inhibitory learning. Incorporating strategies to improve inhibitory learning may improve extinction learning within extinction-based treatments like cognitive behavioral therapy (CBT). Strategies to improve inhibitory learning in CBT are discussed.

Rhythm Perception and Its Role in Perception and Learning of Dysrhythmic Speech.

PubMed

Borrie, Stephanie A; Lansford, Kaitlin L; Barrett, Tyson S

2017-03-01

The perception of rhythm cues plays an important role in recognizing spoken language, especially in adverse listening conditions. Indeed, this has been shown to hold true even when the rhythm cues themselves are dysrhythmic. This study investigates whether expertise in rhythm perception provides a processing advantage for perception (initial intelligibility) and learning (intelligibility improvement) of naturally dysrhythmic speech, dysarthria. Fifty young adults with typical hearing participated in 3 key tests, including a rhythm perception test, a receptive vocabulary test, and a speech perception and learning test, with standard pretest, familiarization, and posttest phases. Initial intelligibility scores were calculated as the proportion of correct pretest words, while intelligibility improvement scores were calculated by subtracting this proportion from the proportion of correct posttest words. Rhythm perception scores predicted intelligibility improvement scores but not initial intelligibility. On the other hand, receptive vocabulary scores predicted initial intelligibility scores but not intelligibility improvement. Expertise in rhythm perception appears to provide an advantage for processing dysrhythmic speech, but a familiarization experience is required for the advantage to be realized. Findings are discussed in relation to the role of rhythm in speech processing and shed light on processing models that consider the consequence of rhythm abnormalities in dysarthria.

Improvement of mechanical properties and life extension of high reliability structural components by laser shock processing

NASA Astrophysics Data System (ADS)

Ocaña, J. L.; Morales, M.; Porro, J. A.; Iordachescu, D.; Díaz, M.; Ruiz de Lara, L.; Correa, C.

2011-05-01

Profiting by the increasing availability of laser sources delivering intensities above 109 W/cm2 with pulse energies in the range of several Joules and pulse widths in the range of nanoseconds, laser shock processing (LSP) is being consolidating as an effective technology for the improvement of surface mechanical and corrosion resistance properties of metals and is being developed as a practical process amenable to production engineering. The main acknowledged advantage of the laser shock processing technique consists on its capability of inducing a relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly, the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Following a short description of the theoretical/computational and experimental methods developed by the authors for the predictive assessment and experimental implementation of LSP treatments, experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (specifically Al and Ti alloys) under different LSP irradiation conditions are presented. In particular, the analysis of the residual stress profiles obtained under different irradiation parameters and the evaluation of the corresponding induced surface properties as roughness and wear resistance are presented.

LEGAL BASES FOR DISCLOSING CONFIDENTIAL PATIENT INFORMATION FOR PUBLIC HEALTH: DISTINGUISHING BETWEEN HEALTH PROTECTION AND HEALTH IMPROVEMENT

PubMed Central

Taylor, Mark J.

2015-01-01

The disclosure of confidential patient data without an individual's explicit consent should be for purposes that persons have reason to both expect and accept. We do not currently have the required level of clarity or consistency in understanding regarding the disclosure of confidential patient information for public health purposes to support effective public dialogue. The Health Service (Control of Patient Information) Regulations 2002 establish a legal basis in England and Wales for data to be disclosed for public health purposes without patient consent. Under the Regulations, there is more than one potential route towards lawful processing: Data may be processed for public health purposes under both Regulations 3 and 5. The alternatives have different safeguards and conditions attached, and their respective applicability to processing for purposes of public health improvement is currently unclear and subject to review. Beyond the need for clarity regarding the safeguards applicable to processing for particular public health purposes, there are reasons to prefer recognition that Regulation 5 is the most appropriate legal basis for disclosure when the purpose is public health improvement rather than public health protection. Where health improvement, rather than protection, is the aim, there is no justification for discarding the additional safeguards associated with processing under Regulation 5. PMID:25995294

Modified interferometric imaging condition for reverse-time migration

NASA Astrophysics Data System (ADS)

Guo, Xue-Bao; Liu, Hong; Shi, Ying

2018-01-01

For reverse-time migration, high-resolution imaging mainly depends on the accuracy of the velocity model and the imaging condition. In practice, however, the small-scale components of the velocity model cannot be estimated by tomographical methods; therefore, the wavefields are not accurately reconstructed from the background velocity, and the imaging process will generate artefacts. Some of the noise is due to cross-correlation of unrelated seismic events. Interferometric imaging condition suppresses imaging noise very effectively, especially the unknown random disturbance of the small-scale part. The conventional interferometric imaging condition is extended in this study to obtain a new imaging condition based on the pseudo-Wigner distribution function (WDF). Numerical examples show that the modified interferometric imaging condition improves imaging precision.

Discussion of Electrode Conditioning Mechanism Based on Pre-breakdown Current under Non-uniform Electric Field in Vacuum

NASA Astrophysics Data System (ADS)

Yasuoka, Takanori; Kato, Tomohiro; Kato, Katsumi; Okubo, Hitoshi

Electrode conditioning is very important technique for improvement of the insulation performance of vacuum circuit breakers (VCBs). This paper discusses the spark conditioning mechanism under non-uniform electric field focused on the pre-breakdown current. We quantitatively evaluated the spark conditioning effect by analyzing the pre-breakdown current based on Fowler-Nordheim equation. As a result, field enhancement factor β decreased with the increasing in breakdown voltage in the beginning of conditioning process, and finally β was saturated with the saturation of breakdown voltage. In addition, in case of non-uniform field, we found that β on high voltage rod electrode after conditioning varied according to the electric field strength on the rod electrode.

Studies on the preparation of Caro’s acid by ultrasonic enhanced electrochemistry

NASA Astrophysics Data System (ADS)

Li, Linbo; Yu, Zeli; Hong, Tao; Fang, Zhao; Peng, Jishi; Yang, Zhao

2017-06-01

Ultrasonic cavitation effects can generate hydroxyl radicals and high energy, which is widely applied in the field of oxidation currently. Ultrasound-enhanced electrochemical is used to prepare Caro’s acid, which improves the generate rate of Caro’s acid. In this article, the influences of ultrasonic frequency and ultrasonic power on the electrolysis voltage, electrolyte temperature, electrolyte concentration and the concentration of additive in the process of electrochemical preparation of Caro’s acid was studied. And the optimal production conditions were determined. The research results showed that ultrasonic can significantly improve the production of Caro’s acid and the product can increase by about 20 g/L under the best condition.

Investigating factors leading to fogging of glass vials in lyophilized drug products.

PubMed

Abdul-Fattah, Ahmad M; Oeschger, Richard; Roehl, Holger; Bauer Dauphin, Isabelle; Worgull, Martin; Kallmeyer, Georg; Mahler, Hanns-Christian

2013-10-01

Vial "Fogging" is a phenomenon observed after lyophilization due to drug product creeping upwards along the inner vial surface. After the freeze-drying process, a haze of dried powder is visible inside the drug product vial, making it barely acceptable for commercial distribution from a cosmetic point of view. Development studies were performed to identify the root cause for fogging during manufacturing of a lyophilized monoclonal antibody drug product. The results of the studies indicate that drug product creeping occurs during the filling process, leading to vial fogging after lyophilization. Glass quality/inner surface, glass conversion/vial processing (vial "history") and formulation excipients, e.g., surfactants (three different surfactants were tested), all affect glass fogging to a certain degree. Results showed that the main factor to control fogging is primarily the inner vial surface hydrophilicity/hydrophobicity. While Duran vials were not capable of reliably improving the level of fogging, hydrophobic containers provided reliable means to improve the cosmetic appearance due to reduction in fogging. Varying vial depyrogenation treatment conditions did not lead to satisfying results in removal of the fogging effect. Processing conditions of the vial after filling with drug product had a strong impact on reducing but not eliminating fogging. Copyright © 2013 Elsevier B.V. All rights reserved.

Stepped-frequency GPR for utility line detection using polarization-dependent scattering

NASA Astrophysics Data System (ADS)

Jensen, Ole K.; Gregersen, Ole G.

2000-04-01

A GPR for detection of buried cables and pipes is developed by Ekko Dane Production in cooperation with Aalborg University. The appearance is a 'lawn mower' model including antennas, electronics and on-line data processing. A successful result is obtained by combining dedicated hardware and signal processing. The inherent signal to clutter ratio is bad, but making measurements at many polarization angles and subsequent signal processing improves the ratio. A simple model of the polarization dependence of the scattering from the target is used. The method is improved by combining the polarization filtering with averaging over small horizontal displacements. A stepped frequency measurement system is used. The method often implies long measurement times, but this problem is overcome by development of fast RF-electronics. Standard signal processors are used for real-time data processing. Several antenna array configurations are tested and optimized for low coupling between transmitter and receiver and for a short impulse response. A large number of tests have been made for different targets, e.g. metal cables and plastic pipes filled with air or water. Tests have been made under realistic ground conditions, including sand, wet clay, pavements and grass covered soil. The results show reliable detection even when the conditions are difficult.

Growth response of broilers to spray-dried plasma in pelleted or expanded feed processed at high temperature.

PubMed

Campbell, J M; Russell, L E; Crenshaw, J D; Behnke, K C; Clark, P M

2006-09-01

A series of 4 experiments evaluated effects of mash conditioning temperature from a pellet mill or expander on performance of broilers fed pelleted diets containing spray-dried plasma (SDP). All experiments utilized Ross x Ross 308 male broilers randomly assigned to their respective treatments (6 or 10 broilers/pen and 8 or 10 pens/treatment). Treatments in Exp. 1 consisted of a control (0% SDP), SDP coated postpelleting, or SDP blended into the meal prepelleting. Experiment 2 and 3 included the same 3 treatments as in Exp. 1 but with additional treatments of SDP blended into the meal and conditioned at 90 or 95 degrees C before pelleting. In Exp. 4, treatments consisted of a control (0% SDP) or SDP blended into the meal and pelleted (85 degrees C conditioning temperature) or expanded (149 degrees C final effective temperature) and then pelleted. Corn-soybean meal-based diets were formulated to be equal in lysine and ME in all experiments. Pelleted diets were conditioned for 15 s at 85 degrees C, and expanded diets were conditioned at 95 degrees C, 29.7 MJ/t, 13.95 kg/cm2 cone pressure, exit temperature of 149 degrees C, and then pelleted through a 4 x 32-mm die. In Exp. 1, ADG and feed intake were improved (P < 0.05) for broilers fed SDP from d 1 to 28 of age, with greater BW at d 42. In Exp. 2, both in early (d 1 to 28 of age) phases, and overall (d 1 to 42 of age), broilers fed SDP had improved (P < 0.05) gain and efficiency. In Exp. 3, ADG, feed intake, efficiency of gain, and BW were improved (P < 0.01) for broilers fed SDP from d 1 to 21 of age, regardless of conditioning temperature. In Exp. 4, broilers fed SDP had improved (P < 0.05) gain, BW, and feed intake regardless of processing method. Overall, the results of all of the experiments demonstrated that pellet conditioning temperature from 85 to 95 degrees C and expander temperatures to 149 degrees C did not impair the positive growth effects of SDP in pelleted or expanded broiler feed.

Method and apparatus for improved melt flow during continuous strip casting

DOEpatents

Follstaedt, Donald W.; King, Edward L.; Schneider, Ken C.

1991-11-12

The continuous casting of metal strip using the melt overflow process is improved by controlling the weir conditions in the nozzle to provide a more uniform flow of molten metal across the width of the nozzle and reducing the tendency for freezing of metal along the interface with refractory surfaces. A weir design having a sloped rear wall and tapered sidewalls and critical gap controls beneath the weir has resulted in the drastic reduction in edge tearing and a significant improvement in strip uniformity. The floor of the container vessel is preferably sloped and the gap between the nozzle and the rotating substrate is critically controlled. The resulting flow patterns observed with the improved casting process have reduced thermal gradients in the bath, contained surface slag and eliminated undesirable solidification near the discharge area by increasing the flow rates at those points.

Method and apparatus for improved melt flow during continuous strip casting

DOEpatents

Follstaedt, D.W.; King, E.L.; Schneider, K.C.

1991-11-12

The continuous casting of metal strip using the melt overflow process is improved by controlling the weir conditions in the nozzle to provide a more uniform flow of molten metal across the width of the nozzle and reducing the tendency for freezing of metal along the interface with refractory surfaces. A weir design having a sloped rear wall and tapered sidewalls and critical gap controls beneath the weir has resulted in the drastic reduction in edge tearing and a significant improvement in strip uniformity. The floor of the container vessel is preferably sloped and the gap between the nozzle and the rotating substrate is critically controlled. The resulting flow patterns observed with the improved casting process have reduced thermal gradients in the bath, contained surface slag and eliminated undesirable solidification near the discharge area by increasing the flow rates at those points. 8 figures.

Improved silicon nitride for advanced heat engines

NASA Technical Reports Server (NTRS)

Yeh, Hun C.; Fang, Ho T.

1987-01-01

The technology base required to fabricate silicon nitride components with the strength, reliability, and reproducibility necessary for actual heat engine applications is presented. Task 2 was set up to develop test bars with high Weibull slope and greater high temperature strength, and to conduct an initial net shape component fabrication evaluation. Screening experiments were performed in Task 7 on advanced materials and processing for input to Task 2. The technical efforts performed in the second year of a 5-yr program are covered. The first iteration of Task 2 was completed as planned. Two half-replicated, fractional factorial (2 sup 5), statistically designed matrix experiments were conducted. These experiments have identified Denka 9FW Si3N4 as an alternate raw material to GTE SN502 Si3N4 for subsequent process evaluation. A detailed statistical analysis was conducted to correlate processing conditions with as-processed test bar properties. One processing condition produced a material with a 97 ksi average room temperature MOR (100 percent of goal) with 13.2 Weibull slope (83 percent of goal); another condition produced 86 ksi (6 percent over baseline) room temperature strength with a Weibull slope of 20 (125 percent of goal).

A new approach for improving reliability of personal navigation devices under harsh GNSS signal conditions.

PubMed

Dhital, Anup; Bancroft, Jared B; Lachapelle, Gérard

2013-11-07

In natural and urban canyon environments, Global Navigation Satellite System (GNSS) signals suffer from various challenges such as signal multipath, limited or lack of signal availability and poor geometry. Inertial sensors are often employed to improve the solution continuity under poor GNSS signal quality and availability conditions. Various fault detection schemes have been proposed in the literature to detect and remove biased GNSS measurements to obtain a more reliable navigation solution. However, many of these methods are found to be sub-optimal and often lead to unavailability of reliability measures, mostly because of the improper characterization of the measurement errors. A robust filtering architecture is thus proposed which assumes a heavy-tailed distribution for the measurement errors. Moreover, the proposed filter is capable of adapting to the changing GNSS signal conditions such as when moving from open sky conditions to deep canyons. Results obtained by processing data collected in various GNSS challenged environments show that the proposed scheme provides a robust navigation solution without having to excessively reject usable measurements. The tests reported herein show improvements of nearly 15% and 80% for position accuracy and reliability, respectively, when applying the above approach.

A New Approach for Improving Reliability of Personal Navigation Devices under Harsh GNSS Signal Conditions

PubMed Central

Dhital, Anup; Bancroft, Jared B.; Lachapelle, Gérard

2013-01-01

In natural and urban canyon environments, Global Navigation Satellite System (GNSS) signals suffer from various challenges such as signal multipath, limited or lack of signal availability and poor geometry. Inertial sensors are often employed to improve the solution continuity under poor GNSS signal quality and availability conditions. Various fault detection schemes have been proposed in the literature to detect and remove biased GNSS measurements to obtain a more reliable navigation solution. However, many of these methods are found to be sub-optimal and often lead to unavailability of reliability measures, mostly because of the improper characterization of the measurement errors. A robust filtering architecture is thus proposed which assumes a heavy-tailed distribution for the measurement errors. Moreover, the proposed filter is capable of adapting to the changing GNSS signal conditions such as when moving from open sky conditions to deep canyons. Results obtained by processing data collected in various GNSS challenged environments show that the proposed scheme provides a robust navigation solution without having to excessively reject usable measurements. The tests reported herein show improvements of nearly 15% and 80% for position accuracy and reliability, respectively, when applying the above approach. PMID:24212120

Automatic humidification system to support the assessment of food drying processes

NASA Astrophysics Data System (ADS)

Ortiz Hernández, B. D.; Carreño Olejua, A. R.; Castellanos Olarte, J. M.

2016-07-01

This work shows the main features of an automatic humidification system to provide drying air that match environmental conditions of different climate zones. This conditioned air is then used to assess the drying process of different agro-industrial products at the Automation and Control for Agro-industrial Processes Laboratory of the Pontifical Bolivarian University of Bucaramanga, Colombia. The automatic system allows creating and improving control strategies to supply drying air under specified conditions of temperature and humidity. The development of automatic routines to control and acquire real time data was made possible by the use of robust control systems and suitable instrumentation. The signals are read and directed to a controller memory where they are scaled and transferred to a memory unit. Using the IP address is possible to access data to perform supervision tasks. One important characteristic of this automatic system is the Dynamic Data Exchange Server (DDE) to allow direct communication between the control unit and the computer used to build experimental curves.

Error affect inoculation for a complex decision-making task.

PubMed

Tabernero, Carmen; Wood, Robert E

2009-05-01

Individuals bring knowledge, implicit theories, and goal orientations to group meetings. Group decisions arise out of the exchange of these orientations. This research explores how a trainee's exploratory and deliberate process (an incremental theory and learning goal orientation) impacts the effectiveness of individual and group decision-making processes. The effectiveness of this training program is compared with another program that included error affect inoculation (EAI). Subjects were 40 Spanish Policemen in a training course. They were distributed in two training conditions for an individual and group decision-making task. In one condition, individuals received the Self-Guided Exploration plus Deliberation Process instructions, which emphasised exploring the options and testing hypotheses. In the other condition, individuals also received instructions based on Error Affect Inoculation (EAI), which emphasised positive affective reactions to errors and mistakes when making decisions. Results show that the quality of decisions increases when the groups share their reasoning. The AIE intervention promotes sharing information, flexible initial viewpoints, and improving the quality of group decisions. Implications and future directions are discussed.

Effects of filler type and content on mechanical properties of photopolymerizable composites measured across two-dimensional combinatorial arrays.

PubMed

Lin-Gibson, Sheng; Sung, Lipiin; Forster, Aaron M; Hu, Haiqing; Cheng, Yajun; Lin, Nancy J

2009-07-01

Multicomponent formulations coupled with complex processing conditions govern the final properties of photopolymerizable dental composites. In this study, a single test substrate was fabricated to support multiple formulations with a gradient in degree of conversion (DC), allowing the evaluation of multiple processing conditions and formulations on one specimen. Mechanical properties and damage response were evaluated as a function of filler type/content and irradiation. DC, surface roughness, modulus, hardness, scratch deformation and cytotoxicity were quantified using techniques including near-infrared spectroscopy, laser confocal scanning microscopy, depth-sensing indentation, scratch testing and cell viability. Scratch parameters (depth, width, percent recovery) were correlated to composite modulus and hardness. Total filler content, nanofiller and irradiation time/intensity all affected the final properties, with the dominant factor for improved properties being a higher DC. This combinatorial platform accelerates the screening of dental composites through the direct comparison of properties and processing conditions across the same sample.

Improved Graphite Fiber.

DTIC Science & Technology

1982-10-01

The purpose of the program was to develop a production method for improved graphite fibers. A goal of 750 x 10 to the 3rd power psi tensile strength...at 60-65 x 10 to the 6th power psi modulus was set for the program. Improved 3-4 micron diameter boron strengthened graphite fibers were successfully... graphite fiber. An average tensile strength of 550 x 10 to the 3rd power psi at the 60 x 10 to the 6th power psi modulus level was achieved through a preliminary optimization of the plant processing conditions.

Training creative cognition: adolescence as a flexible period for improving creativity

PubMed Central

Stevenson, Claire E.; Kleibeuker, Sietske W.; de Dreu, Carsten K. W.; Crone, Eveline A.

2014-01-01

Creativity commonly refers to the ability to generate ideas, solutions, or insights that are novel yet feasible. The ability to generate creative ideas appears to develop and change from childhood to adulthood. Prior research, although inconsistent, generally indicates that adults perform better than adolescents on the alternative uses task (AUT), a commonly used index of creative ideation. The focus of this study was whether performance could be improved by practicing alternative uses generation. We examined the effectiveness of creative ideation training in adolescents (13–16 years, N = 71) and adults (23–30 years, N = 61). Participants followed one of three types of training, each comprising eight 20-min practice sessions within 2 week time: (1) alternative uses generation (experimental condition: creative ideation); (2) object characteristic generation (control condition: general ideation); (3) rule-switching (control condition: rule-switching). Progression in fluency, flexibility, originality of creative ideation was compared between age-groups and training conditions. Participants improved in creative ideation and cognitive flexibility, but not in general ideation. Participants in all three training conditions became better in fluency and originality on the AUT. With regard to originality, adolescents benefitted more from training than adults, although this was not specific for the creative ideation training condition. These results are interpreted in relation to (a) the different underlying processes targeted in the three conditions and (b) developmental differences in brain plasticity with increased sensitivity to training in adolescents. In sum, the results show that improvement can be made in creative ideation and supports the hypothesis that adolescence is a developmental stage of increased flexibility optimized for learning and explorative behavior. PMID:25400565

Effect of load on the tribological properties of hypereutectic Al-Si alloy under boundary lubrication conditions

NASA Astrophysics Data System (ADS)

Kumar, Parveen; Wani, M. F.

2017-11-01

Researchers reported that the IC engine components (piston, cylinder liner etc) fail due to the friction losses (~45%) and wear losses (~25-40%). So the demand of light weight, low friction and wear resistance alloys increases day by day, which reduces the emission and increases the efficiency of the IC engine. In this connection, tribological tests on hypereutectic Al-25Si alloy were performed using a ball-on-disk configuration under dry and lubricated sliding conditions. Hypereutectic Al-25Si alloy was prepared by rapid solidification process with T6 condition. T6 condition improves the friction, wear and mechanical properties of the alloy. Friction coefficient and wear rate of the alloy was measured under high loads ranging from 100 to 300 N. It was found that the friction coefficient (COF) and wear rate of hypereutectic Al-25Si alloy/steel tribo pair increased with increase in load. Significant reduction in COF and wear rate was accomplished with SAE20W50 engine oil and Si particles act as solid lubricant. Optical microscope, 3D surface profilometer and scanning electron microscope (SEM) coupled with an energy dispersive spectrometer (EDS) were used for characterization the worn surface morphologies. The morphology, size and distribution of high Si particles due to its fabrication process caused the improvements in COF and wear rate under lubricated conditions. Adhesive wear, abrasive wear and plastic deformation acted as the dominant wear mechanism for hypereutectic Al-25Si alloy.

Methylphenidate and brain activity in a reward/conflict paradigm: role of the insula in task performance.

PubMed

Ivanov, Iliyan; Liu, Xun; Clerkin, Suzanne; Schulz, Kurt; Fan, Jin; Friston, Karl; London, Edythe D; Schwartz, Jeffrey; Newcorn, Jeffrey H

2014-06-01

Psychostimulants, such as methylphenidate, are thought to improve information processing in motivation-reward and attention-activation networks by enhancing the effects of more relevant signals and suppressing those of less relevant ones; however the nature of such reciprocal influences remains poorly understood. To explore this question, we tested the effect of methylphenidate on performance and associated brain activity in the Anticipation, Conflict, Reward (ACR) task. Sixteen healthy adult volunteers, ages 21-45, were scanned twice using functional magnetic resonance imaging (fMRI) as they performed the ACR task under placebo and methylphenidate conditions. A three-way repeated measures analysis of variance, with cue (reward vs. non-reward), target (congruent vs. incongruent) and medication condition (methylphenidate vs. placebo) as the factors, was used to analyze behaviors on the task. Blood oxygen level dependent (BOLD) signals, reflecting task-related neural activity, were evaluated using linear contrasts. Participants exhibited significantly greater accuracy in the methylphenidate condition than the placebo condition. Compared with placebo, the methylphenidate condition also was associated with lesser task-related activity in components of attention-activation systems irrespective of the reward cue, and less task-related activity in components of the reward-motivation system, particularly the insula, during reward trials irrespective of target difficulty. These results suggest that methylphenidate enhances task performance by improving efficiency of information processing in both reward-motivation and in attention-activation systems. Published by Elsevier B.V.

42 CFR 488.26 - Determining compliance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the need for improvement in relation to the prescribed conditions. (c) The State survey agency must... survey process is the means to assess compliance with Federal health, safety and quality standards; (2... facilities. Specifically surveyors will directly observe the actual provision of care and services to...

Intercity passenger rail : Amtrak needs to improve its decision making process for its route and service proposals

DOT National Transportation Integrated Search

2002-04-01

The National Railroad Passenger Corporation (Amtrak) is the nation's intercity passenger rail operator. In recent years, facing the continuing deterioration of its financial condition and its attempt to eliminate its need for federal operating assist...

Image fusion

NASA Technical Reports Server (NTRS)

Pavel, M.

1993-01-01

The topics covered include the following: a system overview of the basic components of a system designed to improve the ability of a pilot to fly through low-visibility conditions such as fog; the role of visual sciences; fusion issues; sensor characterization; sources of information; image processing; and image fusion.

Troubleshooting crude vacuum tower overhead ejector systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lines, J.R.; Frens, L.L.

1995-03-01

Routinely surveying tower overhead vacuum systems can improve performance and product quality. These vacuum systems normally provide reliable and consistent operation. However, process conditions, supplied utilities, corrosion, erosion and fouling all have an impact on ejector system performance. Refinery vacuum distillation towers use ejector systems to maintain tower top pressure and remove overhead gases. However, as with virtually all refinery equipment, performance may be affected by a number of variables. These variables may act independently or concurrently. It is important to understand basic operating principles of vacuum systems and how performance is affected by: utilities, corrosion and erosion, fouling, andmore » process conditions. Reputable vacuum-system suppliers have service engineers that will come to a refinery to survey the system and troubleshoot performance or offer suggestions for improvement. A skilled vacuum-system engineer may be needed to diagnose and remedy system problems. The affect of these variables on performance is discussed. A case history is described of a vacuum system on a crude tower in a South American refinery.« less

Colour-cueing in visual search.

PubMed

Laarni, J

2001-02-01

Several studies have shown that people can selectively attend to stimulus colour, e.g., in visual search, and that preknowledge of a target colour can improve response speed/accuracy. The purpose was to use a form-identification task to determine whether valid colour precues can produce benefits and invalid cues costs. The subject had to identify the orientation of a "T"-shaped element in a ring of randomly-oriented "L"s when either two or four of the elements were differently coloured. Contrary to Moore and Egeth's (1998) recent findings, colour-based attention did affect performance under data-limited conditions: Colour cues produced benefits when processing load was high; when the load was reduced, they incurred only costs. Surprisingly, a valid colour cue succeeded in improving performance in the high-load condition even when its validity was reduced to the chance level. Overall, the results suggest that knowledge of a target colour does not facilitate the processing of the target, but makes it possible to prioritize it.

A microseismic workflow for managing induced seismicity risk as CO 2 storage projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matzel, E.; Morency, C.; Pyle, M.

2015-10-27

It is well established that fluid injection has the potential to induce earthquakes—from microseismicity to large, damaging events—by altering state-of-stress conditions in the subsurface. While induced seismicity has not been a major operational issue for carbon storage projects to date, a seismicity hazard exists and must be carefully addressed. Two essential components of effective seismic risk management are (1) sensitive microseismic monitoring and (2) robust data interpretation tools. This report describes a novel workflow, based on advanced processing algorithms applied to microseismic data, to help improve management of seismic risk. This workflow has three main goals: (1) to improve themore » resolution and reliability of passive seismic monitoring, (2) to extract additional, valuable information from continuous waveform data that is often ignored in standard processing, and (3) to minimize the turn-around time between data collection, interpretation, and decision-making. These three objectives can allow for a better-informed and rapid response to changing subsurface conditions.« less

Silane-Pyrolysis Reactor With Nonuniform Heating

NASA Technical Reports Server (NTRS)

Iya, Sridhar K.

1991-01-01

Improved reactor serves as last stage in system processing metallurgical-grade silicon feedstock into silicon powder of ultrahigh purity. Silane pyrolized to silicon powder and hydrogen gas via homogeneous decomposition reaction in free space. Features set of individually adjustable electrical heaters and purge flow of hydrogen to improve control of pyrolysis conditions. Power supplied to each heater set in conjunction with flow in reactor to obtain desired distribution of temperature as function of position along reactor.

Effects of alkyl polyglycoside (APG) on composting of agricultural wastes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang Fabao; Gu Wenjie, E-mail: guwenjie1982@yahoo.cn; Xu Peizhi

2011-06-15

Composting is the biological degradation and transformation of organic materials under controlled conditions to promote aerobic decomposition. To find effective ways to accelerate composting and improve compost quality, numerous methods including additive addition, inoculation of microorganisms, and the use of biosurfactants have been explored. Studies have shown that biosurfactant addition provides more favorable conditions for microorganism growth, thereby accelerating the composting process. However, biosurfactants have limited applications because they are expensive and their use in composting and microbial fertilizers is prohibited. Meanwhile, alkyl polyglycoside (APG) is considered a 'green' surfactant. This study aims to determine whether APG addition into amore » compost reaction vessel during 28-day composting can enhance the organic matter degradation and composting process of dairy manure. Samples were periodically taken from different reactor depths at 0, 3, 5, 7, 14, 21, and 28 days. pH levels, electrical conductivity (EC), ammonium and nitrate nitrogen, seed germination indices, and microbial population were determined. Organic matter and total nitrogen were also measured. Compared with the untreated control, the sample with APG exhibited slightly increased microbial populations, such as bacteria, fungi, and actinomycetes. APG addition increased temperatures without substantially affecting compost pH and EC throughout the process. After 28 days, APG addition increased nitrate nitrogen concentrations, promoted matter degradation, and increased seed germination indices. The results of this study suggest that the addition of APG provides more favorable conditions for microorganism growth, slightly enhancing organic matter decomposition and accelerating the composting process, improving the compost quality to a certain extent.« less

Effects of alkyl polyglycoside (APG) on composting of agricultural wastes.

PubMed

Zhang, Fabao; Gu, Wenjie; Xu, Peizhi; Tang, Shuanhu; Xie, Kaizhi; Huang, Xu; Huang, Qiaoyi

2011-06-01

Composting is the biological degradation and transformation of organic materials under controlled conditions to promote aerobic decomposition. To find effective ways to accelerate composting and improve compost quality, numerous methods including additive addition, inoculation of microorganisms, and the use of biosurfactants have been explored. Studies have shown that biosurfactant addition provides more favorable conditions for microorganism growth, thereby accelerating the composting process. However, biosurfactants have limited applications because they are expensive and their use in composting and microbial fertilizers is prohibited. Meanwhile, alkyl polyglycoside (APG) is considered a "green" surfactant. This study aims to determine whether APG addition into a compost reaction vessel during 28-day composting can enhance the organic matter degradation and composting process of dairy manure. Samples were periodically taken from different reactor depths at 0, 3, 5, 7, 14, 21, and 28 days. pH levels, electrical conductivity (EC), ammonium and nitrate nitrogen, seed germination indices, and microbial population were determined. Organic matter and total nitrogen were also measured. Compared with the untreated control, the sample with APG exhibited slightly increased microbial populations, such as bacteria, fungi, and actinomycetes. APG addition increased temperatures without substantially affecting compost pH and EC throughout the process. After 28 days, APG addition increased nitrate nitrogen concentrations, promoted matter degradation, and increased seed germination indices. The results of this study suggest that the addition of APG provides more favorable conditions for microorganism growth, slightly enhancing organic matter decomposition and accelerating the composting process, improving the compost quality to a certain extent. Copyright © 2011 Elsevier Ltd. All rights reserved.

Speech Intelligibility in Various Noise Conditions with the Nucleus® 5 CP810 Sound Processor.

PubMed

Dillier, Norbert; Lai, Wai Kong

2015-06-11

The Nucleus(®) 5 System Sound Processor (CP810, Cochlear™, Macquarie University, NSW, Australia) contains two omnidirectional microphones. They can be configured as a fixed directional microphone combination (called Zoom) or as an adaptive beamformer (called Beam), which adjusts the directivity continuously to maximally reduce the interfering noise. Initial evaluation studies with the CP810 had compared performance and usability of the new processor in comparison with the Freedom™ Sound Processor (Cochlear™) for speech in quiet and noise for a subset of the processing options. This study compares the two processing options suggested to be used in noisy environments, Zoom and Beam, for various sound field conditions using a standardized speech in noise matrix test (Oldenburg sentences test). Nine German-speaking subjects who previously had been using the Freedom speech processor and subsequently were upgraded to the CP810 device participated in this series of additional evaluation tests. The speech reception threshold (SRT for 50% speech intelligibility in noise) was determined using sentences presented via loudspeaker at 65 dB SPL in front of the listener and noise presented either via the same loudspeaker (S0N0) or at 90 degrees at either the ear with the sound processor (S0NCI+) or the opposite unaided ear (S0NCI-). The fourth noise condition consisted of three uncorrelated noise sources placed at 90, 180 and 270 degrees. The noise level was adjusted through an adaptive procedure to yield a signal to noise ratio where 50% of the words in the sentences were correctly understood. In spatially separated speech and noise conditions both Zoom and Beam could improve the SRT significantly. For single noise sources, either ipsilateral or contralateral to the cochlear implant sound processor, average improvements with Beam of 12.9 and 7.9 dB in SRT were found. The average SRT of -8 dB for Beam in the diffuse noise condition (uncorrelated noise from both sides and back) is truly remarkable and comparable to the performance of normal hearing listeners in the same test environment. The static directivity (Zoom) option in the diffuse noise condition still provides a significant benefit of 5.9 dB in comparison with the standard omnidirectional microphone setting. These results indicate that CI recipients may improve their speech recognition in noisy environments significantly using these directional microphone-processing options.

Cognitive Processing in Non-Communicative Patients: What Can Event-Related Potentials Tell Us?

PubMed Central

Lugo, Zulay R.; Quitadamo, Lucia R.; Bianchi, Luigi; Pellas, Fréderic; Veser, Sandra; Lesenfants, Damien; Real, Ruben G. L.; Herbert, Cornelia; Guger, Christoph; Kotchoubey, Boris; Mattia, Donatella; Kübler, Andrea; Laureys, Steven; Noirhomme, Quentin

2016-01-01

Event-related potentials (ERP) have been proposed to improve the differential diagnosis of non-responsive patients. We investigated the potential of the P300 as a reliable marker of conscious processing in patients with locked-in syndrome (LIS). Eleven chronic LIS patients and 10 healthy subjects (HS) listened to a complex-tone auditory oddball paradigm, first in a passive condition (listen to the sounds) and then in an active condition (counting the deviant tones). Seven out of nine HS displayed a P300 waveform in the passive condition and all in the active condition. HS showed statistically significant changes in peak and area amplitude between conditions. Three out of seven LIS patients showed the P3 waveform in the passive condition and five of seven in the active condition. No changes in peak amplitude and only a significant difference at one electrode in area amplitude were observed in this group between conditions. We conclude that, in spite of keeping full consciousness and intact or nearly intact cortical functions, compared to HS, LIS patients present less reliable results when testing with ERP, specifically in the passive condition. We thus strongly recommend applying ERP paradigms in an active condition when evaluating consciousness in non-responsive patients. PMID:27895567

[Sanitary and epidemiological conditions in the Lodz region during the period of the second Polish Republic in the XIX and XX centuries].

PubMed

Sadowska, Jolanta

2005-01-01

Throughout history of European agglomerations in the nineteenth and twentieth century the relation between expanding industry and worsening sanitary and epidemiological conditions was seen. These changes, having great impact on public health, were investigated in the present study. Problems related to sanitary and epidemiological conditions in Lodz first emerged during the Russian occupation of Poland in the XIX century. The Russian Governing Council was not overseeing sanitary conditions of the city, and transferred this responsibility to the industrial bourgeoisie of Lodz. In this situation, uncontrolled development of the industry led to serious deterioration in natural environment and increase of risk for acute and chronic infectious diseases. Improvement of the sanitary situation in Lodz commenced in the period of the Second Polish Republic (1918-1939). Sanitary Divisions were created at the Lodz Department of Public Health. Activities in this Department involved, among others, detailed epidemiological examination of potable water, the investigation of manufacturing processes, retail and wholesale groceries, hygienic conditions of public housing. The activity and interventions of Sanitary Divisions contributed substantially to a decrease of incidence of various diseases and improvement of living conditions of the Lodz populations. The improvement of sanitary and epidemiological conditions in Lodz after 1918 was mainly related to the construction of water supply and sewage systems. This led to an approximation of the urban standards of this 500,000 population agglomeration to European standards.

Grain Boundary Engineering the Mechanical Properties of Allvac 718Plus(Trademark) Superalloy

NASA Technical Reports Server (NTRS)

Gabb, Timothy P.; Telesman, Jack; Garg, Anita; Lin, Peter; Provenzano, virgil; Heard, Robert; Miller, Herbert M.

2010-01-01

Grain Boundary Engineering can enhance the population of structurally-ordered "low S" Coincidence Site Lattice (CSL) grain boundaries in the microstructure. In some alloys, these "special" grain boundaries have been reported to improve overall resistance to corrosion, oxidation, and creep resistance. Such improvements could be quite beneficial for superalloys, especially in conditions which encourage damage and cracking at grain boundaries. Therefore, the effects of GBE processing on high-temperature mechanical properties of the cast and wrought superalloy Allvac 718Plus (Allvac ATI) were screened. Bar sections were subjected to varied GBE processing, and then consistently heat treated, machined, and tested at 650 C. Creep, tensile stress relaxation, and dwell fatigue crack growth tests were performed. The influences of GBE processing on microstructure, mechanical properties, and associated failure modes are discussed.

An experimental study of factors affecting the selective inhibition of sintering process

NASA Astrophysics Data System (ADS)

Asiabanpour, Bahram

Selective Inhibition of Sintering (SIS) is a new rapid prototyping method that builds parts in a layer-by-layer fabrication basis. SIS works by joining powder particles through sintering in the part's body, and by sintering inhibition of some selected powder areas. The objective of this research has been to improve the new SIS process, which has been invented at USC. The process improvement is based on statistical design of experiments. To conduct the needed experiments a working machine and related path generator software were needed. The machine and its control software were made available prior to this research. The path generator algorithms and software had to be created. This program should obtain model geometry data from a CAD file and generate an appropriate path file for the printer nozzle. Also, the program should generate a simulation file for path file inspection using virtual prototyping. The activities related to path generator constitute the first part of this research, which has resulted in an efficient path generator. In addition, to reach an acceptable level of accuracy, strength, and surface quality in the fabricated parts, all effective factors in the SIS process should be identified and controlled. Simultaneous analytical and experimental studies were conducted to recognize effective factors and to control the SIS process. Also, it was known that polystyrene was the most appropriate polymer powder and saturated potassium iodide was the most effective inhibitor among the available candidate materials. In addition, statistical tools were applied to improve the desirable properties of the parts fabricated by the SIS process. An investigation of part strength was conducted using the Response Surface Methodology (RSM) and a region of acceptable operating conditions for the part strength was found. Then, through analysis of the experimental results, the impact of the factors on the final part surface quality and dimensional accuracy was modeled. After developing a desirability function model, process operating conditions for maximum desirability were identified. Finally, the desirability model was validated.

Evaluation of stabilization techniques for ion implant processing

NASA Astrophysics Data System (ADS)

Ross, Matthew F.; Wong, Selmer S.; Minter, Jason P.; Marlowe, Trey; Narcy, Mark E.; Livesay, William R.

1999-06-01

With the integration of high current ion implant processing into volume CMOS manufacturing, the need for photoresist stabilization to achieve a stable ion implant process is critical. This study compares electron beam stabilization, a non-thermal process, with more traditional thermal stabilization techniques such as hot plate baking and vacuum oven processing. The electron beam processing is carried out in a flood exposure system with no active heating of the wafer. These stabilization techniques are applied to typical ion implant processes that might be found in a CMOS production process flow. The stabilization processes are applied to a 1.1 micrometers thick PFI-38A i-line photoresist film prior to ion implant processing. Post stabilization CD variation is detailed with respect to wall slope and feature integrity. SEM photographs detail the effects of the stabilization technique on photoresist features. The thermal stability of the photoresist is shown for different levels of stabilization and post stabilization thermal cycling. Thermal flow stability of the photoresist is detailed via SEM photographs. A significant improvement in thermal stability is achieved with the electron beam process, such that photoresist features are stable to temperatures in excess of 200 degrees C. Ion implant processing parameters are evaluated and compared for the different stabilization methods. Ion implant system end-station chamber pressure is detailed as a function of ion implant process and stabilization condition. The ion implant process conditions are detailed for varying factors such as ion current, energy, and total dose. A reduction in the ion implant systems end-station chamber pressure is achieved with the electron beam stabilization process over the other techniques considered. This reduction in end-station chamber pressure is shown to provide a reduction in total process time for a given ion implant dose. Improvements in the ion implant process are detailed across several combinations of current and energy.

Improving functional value of meat products.

PubMed

Zhang, Wangang; Xiao, Shan; Samaraweera, Himali; Lee, Eun Joo; Ahn, Dong U

2010-09-01

In recent years, much attention has been paid to develop meat and meat products with physiological functions to promote health conditions and prevent the risk of diseases. This review focuses on strategies to improve the functional value of meat and meat products. Value improvement can be realized by adding functional compounds including conjugated linoneleic acid, vitamin E, n3 fatty acids and selenium in animal diets to improve animal production, carcass composition and fresh meat quality. In addition, functional ingredients such as vegetable proteins, dietary fibers, herbs and spices, and lactic acid bacteria can be directly incorporated into meat products during processing to improve their functional value for consumers. Functional compounds, especially peptides, can also be generated from meat and meat products during processing such as fermentation, curing and aging, and enzymatic hydrolysis. This review further discusses the current status, consumer acceptance, and market for functional foods from the global viewpoints. Future prospects for functional meat and meat products are also discussed.

Do High Dynamic Range threatments improve the results of Structure from Motion approaches in Geomorphology?

NASA Astrophysics Data System (ADS)

Gómez-Gutiérrez, Álvaro; Juan de Sanjosé-Blasco, José; Schnabel, Susanne; de Matías-Bejarano, Javier; Pulido-Fernández, Manuel; Berenguer-Sempere, Fernando

2015-04-01

In this work, the hypothesis of improving 3D models obtained with Structure from Motion (SfM) approaches using images pre-processed by High Dynamic Range (HDR) techniques is tested. Photographs of the Veleta Rock Glacier in Spain were captured with different exposure values (EV0, EV+1 and EV-1), two focal lengths (35 and 100 mm) and under different weather conditions for the years 2008, 2009, 2011, 2012 and 2014. HDR images were produced using the different EV steps within Fusion F.1 software. Point clouds were generated using commercial and free available SfM software: Agisoft Photoscan and 123D Catch. Models Obtained using pre-processed images and non-preprocessed images were compared in a 3D environment with a benchmark 3D model obtained by means of a Terrestrial Laser Scanner (TLS). A total of 40 point clouds were produced, georeferenced and compared. Results indicated that for Agisoft Photoscan software differences in the accuracy between models obtained with pre-processed and non-preprocessed images were not significant from a statistical viewpoint. However, in the case of the free available software 123D Catch, models obtained using images pre-processed by HDR techniques presented a higher point density and were more accurate. This tendency was observed along the 5 studied years and under different capture conditions. More work should be done in the near future to corroborate whether the results of similar software packages can be improved by HDR techniques (e.g. ARC3D, Bundler and PMVS2, CMP SfM, Photosynth and VisualSFM).

Analysis of the effects of stirring condition of separation of thorium in the elution process of monazite partial solution by solvent impregnated resin method

NASA Astrophysics Data System (ADS)

Prassanti, R.; Putra, D. S.; Kusuma, B. P.; Nawawi, F. W.

2018-01-01

Monazite is a natural mineral which contains abundant valuable element such as Radioactive Element and Rare Earth Element(REE). In this experiment, it is proven that solution of residual Thorium Sulfate from Monazite mineral process, can be seperated selectively by using extracting method of Solvent Impregnated Resin(SIR), with the elutant solution HNO3. In the earlier process, Thorium solution is conditioned at PH 1 by using H2SO4. Then REE, Thorium and Uranium elements are seperated. This seperation is conducted by using adsorption method by Amberlite XAD-16 Resin, which has been impregnated by Tributhyl Phosphate extractant. It is continued with elution process, which is aimed to obtain Thorium solution of a higher level of concentration. This elution process is conducted by using HNO3, with the elution variables of the lenght of mixing and amount concentration elutant. Based on this experiment, SIR extracting method is able to dissolve Thorium solution until 63,2%grade and a higher level of %grade about 92,40%. It can be concluded that this SIR method can extracted Thorium elements selectively, improve extracting process recovery, and determine optimum stripping condition in the 45th minutes with elutant concentration of 1,0M HNO3.

Plasma-assisted ohmic contact for AlGaN/GaN heterostructure field-effect transistors

NASA Astrophysics Data System (ADS)

Zhang, Jiaqi; Wang, Lei; Wang, Qingpeng; Jiang, Ying; Li, Liuan; Zhu, Huichao; Ao, Jin-Ping

2016-03-01

An Al-based ohmic process assisted by an inductively coupled plasma (ICP) recess treatment is proposed for AlGaN/GaN heterostructure field-effect transistors (HFETs) to realize ohmic contact, which is only needed to anneal at 500 °C. The recess treatment was done with SiCl4 plasma with 100 W ICP power for 20 s and annealing at 575 °C for 1 min. Under these conditions, contact resistance of 0.52 Ωmm was confirmed. To suppress the ball-up phenomenon and improve the surface morphology, an Al/TiN structure was also fabricated with the same conditions. The contact resistance was further improved to 0.30 Ωmm. By using this plasma-assisted ohmic process, a gate-first HFET was fabricated. The device showed high drain current density and high transconductance. The leakage current of the TiN-gate device decreased to 10-9 A, which was 5 orders of magnitude lower than that of the device annealed at 800 °C. The results showed that the low-temperature ohmic contact process assisted by ICP treatment is promising for the fabrication of gate-first and self-aligned gate HFETs.

Essential conditions for the implementation of comprehensive school health to achieve changes in school culture and improvements in health behaviours of students.

PubMed

Storey, Kate E; Montemurro, Genevieve; Flynn, Jenn; Schwartz, Marg; Wright, Erin; Osler, Jill; Veugelers, Paul J; Roberts, Erica

2016-11-02

Comprehensive School Health (CSH) is an internationally recognized framework that holistically addresses school health by transforming the school culture. It has been shown to be effective in enhancing health behaviours among students while also improving educational outcomes. Despite this effectiveness, there is a need to focus on how CSH is implemented. Previous studies have attempted to uncover the conditions necessary for successful operationalization, but none have described them in relation to a proven best practice model of implementation that has demonstrated positive changes to school culture and improvements in health behaviours. The purpose of this research was to identify the essential conditions of CSH implementation utilizing secondary analysis of qualitative interview data, incorporating a multitude of stakeholder perspectives. This included inductive content analysis of teacher (n = 45), principal (n = 46), and school health facilitator (n = 34) viewpoints, all of whom were employed within successful CSH project schools in Alberta, Canada between 2008 and 2013. Many themes were identified, here called conditions, that were divided into two categories: 'core conditions' (students as change agents, school-specific autonomy, demonstrated administrative leadership, dedicated champion to engage school staff, community support, evidence, professional development) and 'contextual conditions' (time, funding and project supports, readiness and prior community connectivity). Core conditions were defined as those conditions necessary for CSH to be successfully implemented, whereas contextual conditions had a great degree of influence on the ability for the core conditions to be obtained. Together, and in consideration of already established 'process conditions' developed by APPLE Schools (assess, vision, prioritize; develop and implement an action plan; monitor, evaluate, celebrate), these represent the essential conditions of successful CSH implementation. Overall, the present research contributes to the evidence-base of CSH implementation, ultimately helping to shape its optimization by providing school communities with a set of understandable essential conditions for CSH implementation. Such research is important as it helps to support and bolster the CSH framework that has been shown to improve the education, health, and well-being of school-aged children.

Accelerated simulation of stochastic particle removal processes in particle-resolved aerosol models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curtis, J.H.; Michelotti, M.D.; Riemer, N.

2016-10-01

Stochastic particle-resolved methods have proven useful for simulating multi-dimensional systems such as composition-resolved aerosol size distributions. While particle-resolved methods have substantial benefits for highly detailed simulations, these techniques suffer from high computational cost, motivating efforts to improve their algorithmic efficiency. Here we formulate an algorithm for accelerating particle removal processes by aggregating particles of similar size into bins. We present the Binned Algorithm for particle removal processes and analyze its performance with application to the atmospherically relevant process of aerosol dry deposition. We show that the Binned Algorithm can dramatically improve the efficiency of particle removals, particularly for low removalmore » rates, and that computational cost is reduced without introducing additional error. In simulations of aerosol particle removal by dry deposition in atmospherically relevant conditions, we demonstrate about 50-times increase in algorithm efficiency.« less

The improvement of surface roughness by polishing method of arcylic door panel at Taishi Tech Sdn Bhd

NASA Astrophysics Data System (ADS)

Basirin, Hammadi bin Mohd; Nawi, Ismail bin Haji Mohd

2017-04-01

This research is an approach to improve the surface roughness for acrylic door panel by using polishing process. The polishing process involve is sanding process by 3 types of sand paper. The sanding process used to improve the surface roughness by using the different grit sizes of sand paper. The experiment was done by using two types of material s, that is plywood and medium density board (MDF). These two materials are the main materials in producing the arcrylic door panel. The surface roughness of these two materials affects the qualities and quantities of the acrylic door panel. The surface structure was measured by using Optical Microscope and Scanning Electron Microscope (SEM) and the surface roughness was measured by using Mitutoyo surfest SJ 400 Tester. Results indicates that using the different types of grit are influence the surface roughness of the material. When the higher types of grit sizes had been used, the average roughness of the surface are decrease. In summary, a good surface roughness condition produced when using the higher types of grit sizes sand paper.

Dramatic Improvement of the Mechanical Strength of Silane-Modified Hydroxyapatite–Gelatin Composites via Processing with Cosolvent

PubMed Central

2018-01-01

Bone tissue engineering (BTE) requires a sturdy biomaterial for scaffolds for restoration of large bone defects. Ideally, the scaffold should have a mechanical strength comparable to the natural bone in the implanted site. We show that adding cosolvent during the processing of our previously developed composite of hydroxyapatite–gelatin with a silane cross-linker can significantly affect its mechanical strength. When processed with tetrahydrofuran (THF) as the cosolvent, the new hydroxyapatite–gelatin composite can demonstrate almost twice the compressive strength (97 vs 195 MPa) and biaxial flexural strength (222 vs 431 MPa) of the previously developed hydroxyapatite–gelatin composite (i.e., processed without THF), respectively. We further confirm that this mechanical strength improvement is due to the improved morphology of both the enTMOS network and the composite. Furthermore, the addition of cosolvents does not appear to negatively impact the cell viability. Finally, the porous scaffold can be easily fabricated, and its compressive strength is around 11 MPa under dry conditions. All these results indicate that this new hydroxyapatite–gelatin composite is a promising material for BTE application. PMID:29623305

Two-phase anaerobic digestion within a solid waste/wastewater integrated management system

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Gioannis, G.; Diaz, L.F.; Muntoni, A.

2008-07-01

A two-phase, wet anaerobic digestion process was tested at laboratory scale using mechanically pre-treated municipal solid waste (MSW) as the substrate. The proposed process scheme differs from others due to the integration of the MSW and wastewater treatment cycles, which makes it possible to avoid the recirculation of process effluent. The results obtained show that the supplying of facultative biomass, drawn from the wastewater aeration tank, to the solid waste acidogenic reactor allows an improvement of the performance of the first phase of the process which is positively reflected on the second one. The proposed process performed successfully, adopting mesophilicmore » conditions and a relatively short hydraulic retention time in the methanogenic reactor, as well as high values of organic loading rate. Significant VS removal efficiency and biogas production were achieved. Moreover, the methanogenic reactor quickly reached optimal conditions for a stable methanogenic phase. Studies conducted elsewhere also confirm the feasibility of integrating the treatment of the organic fraction of MSW with that of wastewater.« less

Keeping Up with What You Have.

ERIC Educational Resources Information Center

Krysiak, Barbara H.

1999-01-01

Numerous studies have reported the deteriorating conditions in school buildings. One of the primary causes of this national problem is lack of proper maintenance of school facilities. Outlines a comprehensive assessment and planning process to provide a district with a road map for making decisions about facility improvement. (MLF)

Taking Steps toward PK-3 Success

ERIC Educational Resources Information Center

Eubanks, Shyrelle

2007-01-01

This tandem brief examines state policies and practices regarding critical PK-3 working conditions and identifies strategies to influence teacher job quality through collective bargaining and other collaborative processes. The document is designed to support efforts to change or implement policies that will improve the teaching and learning…

High-laser-damage-threshold HfO2/SiO2 mirrors manufactured by sputtering process

NASA Astrophysics Data System (ADS)

Fornier, Anne; Bernardino, D.; Lam, Odile; Neauport, Jerome; Dufour, Francois; Schmitt, Bernard R.; Mackowski, Jean-Marie

1999-07-01

A major preoccupation for the design of the LMJ laser is the mirrors laser damage threshold. SAGEM SA, in collaboration with the CEA, has conducted a study in order to improve the laser induced damage threshold under operational conditions.

Conditioning of material properties by micro rotary swaging

NASA Astrophysics Data System (ADS)

Ishkina, Svetlana; Schenck, Christian; Kuhfuss, Bernd

2018-05-01

Cold forming initiates a change of the material properties like flow stress and hardness. Due to work hardening and the accompanied loss of formability some intermediate heat treatment may become necessary in multi-stage forming processes. One possibility to avoid this heat treatment is to adjust the forming characteristics in terms of flow stress and formability by rotary swaging. This process is particularly suitable not only for producing of the target geometry but also for modifying of the material properties during the process and thus, rotary swaging can prepare the parts for further forming, such as extrusion. In this contribution, the process chain "rotary swaging - extrusion" for austenite stainless steel AISI304 was investigated. The forming characteristics of the semi-finished products for the extrusion were influenced by the previous swaging process. The conditioning by changing of the microstructure, the work hardening and the geometry of the processed wires was achieved by the process design. For this purpose, the geometry of the swaging dies, the feeding velocity as well as the process kinematics (eccentric swaging) and a stroke following angle Δɸ were varied. In particular, the novel geometry of the swaging dies with extraordinary sloped faces generated a non-symmetric material flow with severe shear deformation and thus an extreme change of the microstructure. The required forming force of the following extrusion process reflected the range of achievable conditioning. The micro rotary swaging process positively improved the formability of AISI304 by work softening.

Centralized drug review processes: are they fair?

PubMed

Mitton, Craig R; McMahon, Meghan; Morgan, Steve; Gibson, Jennifer

2006-07-01

Numerous countries have implemented centralized drug review processes to assist in making drug coverage decisions. In addition to examining the final recommendations of these bodies, it is also important to ensure fairness in decision making. Accountability for reasonableness is an ethics-based framework for examining the fairness of priority setting processes. The objective of this study was to assess the fairness of four internationally established centralized drug review processes using accountability for reasonableness. Semi-structured telephone interviews were conducted with stakeholders in Canada, New Zealand, Australia and the UK (n=16). Participants were asked to evaluate their country's centralized drug review process against the four conditions of accountability for reasonableness. Each centralized drug review process satisfied at least one of the four ethical conditions, but none satisfied all four conditions. All participants viewed transparency as critical to both the legitimacy and fairness of centralized drug review processes. Additional strides need to be made in each of the four countries under study to improve the fairness of their centralized drug review processes. Ideally, a fair priority setting process should foster constructive stakeholder engagement and enhance the legitimacy of decisions made in assessing pharmaceutical products for funding. As policy makers are under increasing scrutiny in allocating limited resources, fair process should be seen as a critical component of such activity. This study represents the first attempt to conduct an international comparison of the fairness of centralized drug review agencies in the eyes of participating stakeholders.

Improving the health care work environment: implications for research, practice, and policy.

PubMed

Harrison, Michael I; Henriksen, Kerm; Hughes, Ronda G

2007-11-01

Despite the gains to date, we need better understanding of practices for implementing and sustaining improvements in health care work environments and further study of organizational conditions affecting implementation of improvements. Limiting work hours, improving schedules, and providing sleep hygiene training will help combat clinician fatigue. Hospital crowding can be reduced through systemwide improvement of patient flow and capacity management, coupled with management support, measurement, and reporting on crowding. Long-term solutions to nurse staffing shortfalls include process redesign to enhance efficiency. Improvement of organizational climate, human resource management, and interoccupational relations will also contribute to staff retention. Evidence-based enhancements to patient rooms and other physical features in hospitals contribute directly to safety and quality and also affect staff performance. POLICY: Landrigan and his colleagues call for external restrictions on residents' work shifts. Clarke examines prospects for mandated nursing-staff ratios. Public reporting on staffing, crowding, and other risks may incent change. Reporting and pay for performance require standardized measures of targeted conditions. Organizations promoting care quality can help spread safe work practices; they can also support collaborative learning and other strategies that may enhance implementation of improvements in work environments.

Structure-based protein engineering for thermostable and alkaliphilic enhancement of endo-β-1,4-xylanase for applications in pulp bleaching.

PubMed

Boonyapakron, Katewadee; Jaruwat, Aritsara; Liwnaree, Benjamas; Nimchua, Thidarat; Champreda, Verawat; Chitnumsub, Penchit

2017-10-10

In the pulp bleaching industry, enzymes with robust activity at high pH and temperatures are desirable for facilitating the pre-bleaching process with simplified processing and minimal use of chlorinated compounds. To engineer an enzyme for this purpose, we determined the crystal structure of the Xyn12.2 xylanase, a xylan-hydrolyzing enzyme derived from the termite gut symbiont metagenome, as the basis for structure-based protein engineering to improve Xyn12.2 stability in high heat and alkaline conditions. Engineered cysteine pairs that generated exterior disulfide bonds increased the k cat of Xyn12.2 variants and melting temperature at all tested conditions. These improvements led to up to 4.2-fold increases in catalytic efficiency at pH 9.0, 50°C for 1h and up to 3-fold increases at 60°C. The most effective variants, XynTT and XynTTTE, exhibited 2-3-fold increases in bagasse hydrolysis at pH 9.0 and 60°C compared to the wild-type enzyme. Overall, engineering arginines and phenylalanines for increased pK a and hydrogen bonding improved enzyme catalytic efficiency at high stringency conditions. These modifications were the keys to enhancing thermostability and alkaliphilicity in our enzyme variants, with XynTT and XynTTTE being especially promising for their application to the pulp and paper industry. Copyright © 2017 Elsevier B.V. All rights reserved.

Boosting pitch encoding with audiovisual interactions in congenital amusia.

PubMed

Albouy, Philippe; Lévêque, Yohana; Hyde, Krista L; Bouchet, Patrick; Tillmann, Barbara; Caclin, Anne

2015-01-01

The combination of information across senses can enhance perception, as revealed for example by decreased reaction times or improved stimulus detection. Interestingly, these facilitatory effects have been shown to be maximal when responses to unisensory modalities are weak. The present study investigated whether audiovisual facilitation can be observed in congenital amusia, a music-specific disorder primarily ascribed to impairments of pitch processing. Amusic individuals and their matched controls performed two tasks. In Task 1, they were required to detect auditory, visual, or audiovisual stimuli as rapidly as possible. In Task 2, they were required to detect as accurately and as rapidly as possible a pitch change within an otherwise monotonic 5-tone sequence that was presented either only auditorily (A condition), or simultaneously with a temporally congruent, but otherwise uninformative visual stimulus (AV condition). Results of Task 1 showed that amusics exhibit typical auditory and visual detection, and typical audiovisual integration capacities: both amusics and controls exhibited shorter response times for audiovisual stimuli than for either auditory stimuli or visual stimuli. Results of Task 2 revealed that both groups benefited from simultaneous uninformative visual stimuli to detect pitch changes: accuracy was higher and response times shorter in the AV condition than in the A condition. The audiovisual improvements of response times were observed for different pitch interval sizes depending on the group. These results suggest that both typical listeners and amusic individuals can benefit from multisensory integration to improve their pitch processing abilities and that this benefit varies as a function of task difficulty. These findings constitute the first step towards the perspective to exploit multisensory paradigms to reduce pitch-related deficits in congenital amusia, notably by suggesting that audiovisual paradigms are effective in an appropriate range of unimodal performance. Copyright © 2014 Elsevier Ltd. All rights reserved.

Assessment of Antioxidant and Antimicrobial Properties of Lignin from Corn Stover Residue Pretreated with Low-Moisture Anhydrous Ammonia and Enzymatic Hydrolysis Process.

PubMed

Guo, Mingming; Jin, Tony; Nghiem, Nhuan P; Fan, Xuetong; Qi, Phoebe X; Jang, Chan Ho; Shao, Lingxiao; Wu, Changqing

2018-01-01

Lignin accounts for 15-35% of dry biomass materials. Therefore, developing value-added co-products from lignin residues is increasingly important to improve the economic viability of biofuel production from biomass resources. The main objective of this work was to study the lignin extracts from corn stover residue obtained from a new and improved process for bioethanol production. Extraction conditions that favored high lignin yield were optimized, and antioxidant and antimicrobial activities of the resulting lignin were investigated. Potential estrogenic toxicity of lignin extracts was also evaluated. The corn stover was pretreated by low-moisture anhydrous ammonia (LMAA) and then subjected to enzymatic hydrolysis using cellulase and hemicellulase. The residues were then added with sodium hydroxide and extracted for different temperatures and times for enhancing lignin yield and the bioactivities. The optimal extraction conditions using 4% (w/v) sodium hydroxide were determined to be 50 °C, 120 min, and 1:8 (w:v), the ratio between corn stover solids and extracting liquid. Under the optimal condition, 33.92 g of lignin yield per 100 g of corn stover residue was obtained. Furthermore, the extracts produced using these conditions showed the highest antioxidant activity by the hydrophilic oxygen radical absorbance capacity (ORAC) assay. The extracts also displayed significant antimicrobial activities against Listeria innocua. Minimal estrogenic impacts were observed for all lignin extracts when tested using the MCF-7 cell proliferation assay. Thus, the lignin extracts could be used for antioxidant and antimicrobial applications, and improve the value of the co-products from the biomass-based biorefinery.

Precise Positioning of Uavs - Dealing with Challenging Rtk-Gps Measurement Conditions during Automated Uav Flights

NASA Astrophysics Data System (ADS)

Zimmermann, F.; Eling, C.; Klingbeil, L.; Kuhlmann, H.

2017-08-01

For some years now, UAVs (unmanned aerial vehicles) are commonly used for different mobile mapping applications, such as in the fields of surveying, mining or archeology. To improve the efficiency of these applications an automation of the flight as well as the processing of the collected data is currently aimed at. One precondition for an automated mapping with UAVs is that the georeferencing is performed directly with cm-accuracies or better. Usually, a cm-accurate direct positioning of UAVs is based on an onboard multi-sensor system, which consists of an RTK-capable (real-time kinematic) GPS (global positioning system) receiver and additional sensors (e.g. inertial sensors). In this case, the absolute positioning accuracy essentially depends on the local GPS measurement conditions. Especially during mobile mapping applications in urban areas, these conditions can be very challenging, due to a satellite shadowing, non-line-of sight receptions, signal diffraction or multipath effects. In this paper, two straightforward and easy to implement strategies will be described and analyzed, which improve the direct positioning accuracies for UAV-based mapping and surveying applications under challenging GPS measurement conditions. Based on a 3D model of the surrounding buildings and vegetation in the area of interest, a GPS geometry map is determined, which can be integrated in the flight planning process, to avoid GPS challenging environments as far as possible. If these challenging environments cannot be avoided, the GPS positioning solution is improved by using obstruction adaptive elevation masks, to mitigate systematic GPS errors in the RTK-GPS positioning. Simulations and results of field tests demonstrate the profit of both strategies.

Process development of human multipotent stromal cell microcarrier culture using an automated high-throughput microbioreactor.

PubMed

Rafiq, Qasim A; Hanga, Mariana P; Heathman, Thomas R J; Coopman, Karen; Nienow, Alvin W; Williams, David J; Hewitt, Christopher J

2017-10-01

Microbioreactors play a critical role in process development as they reduce reagent requirements and can facilitate high-throughput screening of process parameters and culture conditions. Here, we have demonstrated and explained in detail, for the first time, the amenability of the automated ambr15 cell culture microbioreactor system for the development of scalable adherent human mesenchymal multipotent stromal/stem cell (hMSC) microcarrier culture processes. This was achieved by first improving suspension and mixing of the microcarriers and then improving cell attachment thereby reducing the initial growth lag phase. The latter was achieved by using only 50% of the final working volume of medium for the first 24 h and using an intermittent agitation strategy. These changes resulted in >150% increase in viable cell density after 24 h compared to the original process (no agitation for 24 h and 100% working volume). Using the same methodology as in the ambr15, similar improvements were obtained with larger scale spinner flask studies. Finally, this improved bioprocess methodology based on a serum-based medium was applied to a serum-free process in the ambr15, resulting in >250% increase in yield compared to the serum-based process. At both scales, the agitation used during culture was the minimum required for microcarrier suspension, N JS . The use of the ambr15, with its improved control compared to the spinner flask, reduced the coefficient of variation on viable cell density in the serum containing medium from 7.65% to 4.08%, and the switch to serum free further reduced these to 1.06-0.54%, respectively. The combination of both serum-free and automated processing improved the reproducibility more than 10-fold compared to the serum-based, manual spinner flask process. The findings of this study demonstrate that the ambr15 microbioreactor is an effective tool for bioprocess development of hMSC microcarrier cultures and that a combination of serum-free medium, control, and automation improves both process yield and consistency. Biotechnol. Bioeng. 2017;114: 2253-2266. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Process development of human multipotent stromal cell microcarrier culture using an automated high‐throughput microbioreactor

PubMed Central

Hanga, Mariana P.; Heathman, Thomas R. J.; Coopman, Karen; Nienow, Alvin W.; Williams, David J.; Hewitt, Christopher J.

2017-01-01

ABSTRACT Microbioreactors play a critical role in process development as they reduce reagent requirements and can facilitate high‐throughput screening of process parameters and culture conditions. Here, we have demonstrated and explained in detail, for the first time, the amenability of the automated ambr15 cell culture microbioreactor system for the development of scalable adherent human mesenchymal multipotent stromal/stem cell (hMSC) microcarrier culture processes. This was achieved by first improving suspension and mixing of the microcarriers and then improving cell attachment thereby reducing the initial growth lag phase. The latter was achieved by using only 50% of the final working volume of medium for the first 24 h and using an intermittent agitation strategy. These changes resulted in >150% increase in viable cell density after 24 h compared to the original process (no agitation for 24 h and 100% working volume). Using the same methodology as in the ambr15, similar improvements were obtained with larger scale spinner flask studies. Finally, this improved bioprocess methodology based on a serum‐based medium was applied to a serum‐free process in the ambr15, resulting in >250% increase in yield compared to the serum‐based process. At both scales, the agitation used during culture was the minimum required for microcarrier suspension, NJS. The use of the ambr15, with its improved control compared to the spinner flask, reduced the coefficient of variation on viable cell density in the serum containing medium from 7.65% to 4.08%, and the switch to serum free further reduced these to 1.06–0.54%, respectively. The combination of both serum‐free and automated processing improved the reproducibility more than 10‐fold compared to the serum‐based, manual spinner flask process. The findings of this study demonstrate that the ambr15 microbioreactor is an effective tool for bioprocess development of hMSC microcarrier cultures and that a combination of serum‐free medium, control, and automation improves both process yield and consistency. Biotechnol. Bioeng. 2017;114: 2253–2266. © 2017 The Authors. Biotechnology and Bioengineering Published by Wiley Periodicals, Inc. PMID:28627713

Artificial Intelligent Platform as Decision Tool for Asset Management, Operations and Maintenance.

PubMed

2018-01-04

An Artificial Intelligence (AI) system has been developed and implemented for water, wastewater and reuse plants to improve management of sensors, short and long term maintenance plans, asset and investment management plans. It is based on an integrated approach to capture data from different computer systems and files. It adds a layer of intelligence to the data. It serves as a repository of key current and future operations and maintenance conditions that a plant needs have knowledge of. With this information, it is able to simulate the configuration of processes and assets for those conditions to improve or optimize operations, maintenance and asset management, using the IViewOps (Intelligent View of Operations) model. Based on the optimization through model runs, it is able to create output files that can feed data to other systems and inform the staff regarding optimal solutions to the conditions experienced or anticipated in the future.

Studies in the use of cloud type statistics in mission simulation

NASA Technical Reports Server (NTRS)

Fowler, M. G.; Willand, J. H.; Chang, D. T.; Cogan, J. L.

1974-01-01

A study to further improve NASA's global cloud statistics for mission simulation is reported. Regional homogeneity in cloud types was examined; most of the original region boundaries defined for cloud cover amount in previous studies were supported by the statistics on cloud types and the number of cloud layers. Conditionality in cloud statistics was also examined with special emphasis on temporal and spatial dependencies, and cloud type interdependence. Temporal conditionality was found up to 12 hours, and spatial conditionality up to 200 miles; the diurnal cycle in convective cloudiness was clearly evident. As expected, the joint occurrence of different cloud types reflected the dynamic processes which form the clouds. Other phases of the study improved the cloud type statistics for several region and proposed a mission simulation scheme combining the 4-dimensional atmospheric model, sponsored by MSFC, with the global cloud model.

Cognitive remediation in anorexia nervosa and related conditions: a systematic review.

PubMed

Tchanturia, Kate; Lounes, Naima; Holttum, Sue

2014-11-01

Research evidence for cognitive remediation therapy's (CRT) effectiveness for anorexia nervosa (AN) has been gathering. This approach is also increasingly being implemented in other disorders including major depressive disorder, obsessive-compulsive disorder and autistic spectrum disorder that share commonalities with AN in neuropsychological profiles and clinical presentations. This systematic literature review identified and appraised the current evidence base to see whether evidence from related conditions could be integrated into the theoretical understanding of CRT for AN as well as future AN treatment developments and research. Overall, CRT studies in AN report promising findings, and CRT appears to be associated with improvements in set-shifting and in central coherence. Cognitive remediation approaches in other conditions also show promising evidence in associated improvements in areas of executive functioning and information processing; links are made between AN treatment and what future treatment developments could consider. Copyright © 2014 John Wiley & Sons, Ltd and Eating Disorders Association.

River channel morphology and hydraulics properties due to introduction of plant basket hydraulic structures for river channel management

NASA Astrophysics Data System (ADS)

Kałuża, Tomasz; Radecki-Pawlik, Artur; Plesiński, Karol; Walczak, Natalia; Szoszkiewicz, Krzysztof; Radecki-Pawlik, Bartosz

2016-04-01

In the present time integrated water management is directly connected with management and direct works in river channels themselves which are taking into account morphological processes in rivers and improve flow conditions. Our work focused on the hydraulic and hydrodynamic consequences upon the introduction of the concept of the improvement of the hydromorphological conditions of the Flinta River in a given reach following river channel management concept. Based on a comprehensive study of the hydromorphological state of the river, four sections were selected where restoration measures can efficiently improve river habitat conditions in the river. For each section a set of technical and biological measures were proposed and implemented in practice. One of the proposed solutions was to construct plant basket hydraulic structures (PBHS) within the river channel, which are essentially plant barriers working as sediment traps, changing river channel morphology and are in line with concepts of Water Framework Directive. These relatively small structures work as crested weirs and unquestionably change the channel morphology. Along our work we show the results of three-year long (2013-2015) systematic measurements that provided information on the morphological consequences of introducing such structures into a river channel. Our main conclusions are as follows: 1. Plant basket hydraulic structures cause changes in hydrodynamic conditions and result in sediment accumulation and the formation of river backwaters upstream and downstream the obstacle; 2. The introduced plant basket hydraulic structures cause plant debris accumulation which influences the hydrodynamic flow conditions; 3. The installation of plant basket hydraulic structures on the river bed changes flow pattern as well as flow hydrodynamic conditions causing river braiding process; 4. The erosion rate below the plant basket hydraulic structures is due to the hydraulic work conditions of the PBHS and its calculated value was confirmed by direct measurements in the field. In our calculations we used VCmaster software. This Work funded by the National Science Centre allocated based on the number of decision: DEC-2011/01 / B / ST10 / 06959

Study on optimum technological conditions of ore sintering flue gas desulfurization by using poor manganese

NASA Astrophysics Data System (ADS)

Li, H. Y.; Li, S. E.; Long, Z. G.; Wu, F. Z.; Cui, T. M.; Zhou, X. Z.

2017-11-01

Orthogonal experiments were conducted to study the effect of each single factor on the desulfurization rate and leaching rate of Mn2+ to obtain improved process parameters. The results showed that the use of pyrolusite flue gas and the process method of by-product MnSO4 can not only effectively remove the sulfur in the gas, thereby controlling environmental pollution, but can also recover sulfur.

Probiotics production and alternative encapsulation methodologies to improve their viabilities under adverse environmental conditions.

PubMed

Coghetto, Chaline Caren; Brinques, Graziela Brusch; Ayub, Marco Antônio Záchia

2016-12-01

Probiotic products are dietary supplements containing live microorganisms producing beneficial health effects on the host by improving intestinal balance and nutrient absorption. Among probiotic microorganisms, those classified as lactic acid bacteria are of major importance to the food and feed industries. Probiotic cells can be produced using alternative carbon and nitrogen sources, such as agroindustrial residues, at the same time contributing to reduce process costs. On the other hand, the survival of probiotic cells in formulated food products, as well as in the host gut, is an essential nutritional aspect concerning health benefits. Therefore, several cell microencapsulation techniques have been investigated as a way to improve cell viability and survival under adverse environmental conditions, such as the gastrointestinal milieu of hosts. In this review, different aspects of probiotic cells and technologies of their related products are discussed, including formulation of culture media, and aspects of cell microencapsulation techniques required to improve their survival in the host.

Method to Prepare Processable Polymides with Reactive Endgroups using 1,3-Bis (3-Aminophenoxy) Benzene

NASA Technical Reports Server (NTRS)

Jensen, Brian J. (Inventor)

2000-01-01

Polyimide copolymers were obtained containing 1,3-bis(3-aminophenoxy)benzene (APB) and other diamines and dianhydrides and terminating with the appropriate amount of reactive endcapper. The reactive endcappers studied include but should not be limited to 4-phenylethynyl phthalic anhydride (PEPA ), 3-aminophenoxy- 4'-phenylethynylbenzophenone (3-APEB), maleic anhydride (MA) and nadic anhydride (5-norbomene-2,3-dicarboxylic anhydride, NA). Homopolymers containing only other diamines and dianhydrides which are not processable under conditions described previously can be made processable by incorporating various amounts of APB, depending on the chemical structures of the diamines and dianhydrides used. By simply changing the ratio of APB to the other diamine in the polyimide backbone, a material with a unique combination of solubility, Tg, Tm, melt viscosity, toughness and elevated temperature mechanical properties can be prepared. The copolymers that result from using APB to enhance processability have a unique combination of properties that include low pressure processing (200 psi and below), long term melt stability (several hours at 300 C. for the phenylethynyl terminated polymers), high toughness, improved solvent resistance, improved adhesive properties, and improved composite mechanical properties. These copolyimides are eminently suitable as adhesives, composite matrices, moldings, films and coatings.

Evidence of an amnesia-like cued-recall memory impairment in nondementing idiopathic Parkinson's disease.

PubMed

Edelstyn, Nicola M J; John, Christopher M; Shepherd, Thomas A; Drakeford, Justine L; Clark-Carter, David; Ellis, Simon J; Mayes, Andrew R

2015-10-01

Medicated, non-dementing mild-to-moderate Parkinson's disease (PD) patients usually show recall/recollection impairments but have only occasionally shown familiarity impairments. We aimed to assess two explanations of this pattern of impairment. Recollection typically improves when effortful planning of encoding and retrieval processing is engaged. This depends on prefrontally-dependent executive processes, which are often disrupted in PD. Relative to an unguided encoding and retrieval of words condition (C1), giving suitable guidance at encoding alone (C2) or at encoding and retrieval (C3) should, if executive processes are disrupted, improve PD recollection more than control recollection and perhaps raise it to normal levels. Familiarity, being a relatively automatic kind of memory, whether impaired or intact, should be unaffected by guidance. According to the second explanation, PD deficits are amnesia-like and caused by medial temporal lobe dysfunction and although poorer recollection, which is caused by hippocampal disruption, may be improved by guidance, it should not improve more than control recollection. Familiarity impairment will also occur if the perirhinal cortex is disrupted, but will be unimproved by guidance. Without guidance, recollection/recall was impaired in thirty PD patients relative to twenty-two healthy controls and remained relatively equally impaired when full guidance was provided (C1 vs C3), both groups improving to broadly the same extent. Although impaired, and markedly less so than recollection, familiarity was not improved by guidance in both groups. The patients showed elevated rates of subclinical depressive symptoms, which weakly correlated with recall/recollection in all three conditions. PD executive function was also deficient and correlated with unguided/C1 recollection only. Our results are consistent with a major cause of the patients' recall/recollection impairments being hippocampal disruption, probably exacerbated by subclinical depressive symptoms. However, the results do not exclude a lesser prefrontal cortex contribution because patient executive functions were impaired and correlated solely with unguided overall recollection. Copyright © 2015 Elsevier Ltd. All rights reserved.

The labor movement's role in gaining federal safety and health standards to protect America's workers.

PubMed

Weinstock, Deborah; Failey, Tara

2014-11-01

In the United States, unions sometimes joined by worker advocacy groups (e.g., Public Citizen and the American Public Health Association) have played a critical role in strengthening worker safety and health protections. They have sought to improve standards that protect workers by participating in the rulemaking process, through written comments and involvement in hearings; lobbying decision-makers; petitioning the Department of Labor; and defending improved standards in court. Their efforts have culminated in more stringent exposure standards, access to information about the presence of potentially hazardous toxic chemicals, and improved access to personal protective equipment-further improving working conditions in the United States.

Biocatalytic Conversion of Avermectin to 4″-Oxo-Avermectin: Improvement of Cytochrome P450 Monooxygenase Specificity by Directed Evolution▿ †

PubMed Central

Trefzer, Axel; Jungmann, Volker; Molnár, István; Botejue, Ajit; Buckel, Dagmar; Frey, Gerhard; Hill, D. Steven; Jörg, Mario; Ligon, James M.; Mason, Dylan; Moore, David; Pachlatko, J. Paul; Richardson, Toby H.; Spangenberg, Petra; Wall, Mark A.; Zirkle, Ross; Stege, Justin T.

2007-01-01

Discovery of the CYP107Z subfamily of cytochrome P450 oxidases (CYPs) led to an alternative biocatalytic synthesis of 4″-oxo-avermectin, a key intermediate for the commercial production of the semisynthetic insecticide emamectin. However, under industrial process conditions, these wild-type CYPs showed lower yields due to side product formation. Molecular evolution employing GeneReassembly was used to improve the regiospecificity of these enzymes by a combination of random mutagenesis, protein structure-guided site-directed mutagenesis, and recombination of multiple natural and synthetic CYP107Z gene fragments. To assess the specificity of CYP mutants, a miniaturized, whole-cell biocatalytic reaction system that allowed high-throughput screening of large numbers of variants was developed. In an iterative process consisting of four successive rounds of GeneReassembly evolution, enzyme variants with significantly improved specificity for the production of 4″-oxo-avermectin were identified; these variants could be employed for a more economical industrial biocatalytic process to manufacture emamectin. PMID:17483257

Suppressing molecular vibrations in organic semiconductors by inducing strain

PubMed Central

Kubo, Takayoshi; Häusermann, Roger; Tsurumi, Junto; Soeda, Junshi; Okada, Yugo; Yamashita, Yu; Akamatsu, Norihisa; Shishido, Atsushi; Mitsui, Chikahiko; Okamoto, Toshihiro; Yanagisawa, Susumu; Matsui, Hiroyuki; Takeya, Jun

2016-01-01

Organic molecular semiconductors are solution processable, enabling the growth of large-area single-crystal semiconductors. Improving the performance of organic semiconductor devices by increasing the charge mobility is an ongoing quest, which calls for novel molecular and material design, and improved processing conditions. Here we show a method to increase the charge mobility in organic single-crystal field-effect transistors, by taking advantage of the inherent softness of organic semiconductors. We compress the crystal lattice uniaxially by bending the flexible devices, leading to an improved charge transport. The mobility increases from 9.7 to 16.5 cm2 V−1 s−1 by 70% under 3% strain. In-depth analysis indicates that compressing the crystal structure directly restricts the vibration of the molecules, thus suppresses dynamic disorder, a unique mechanism in organic semiconductors. Since strain can be easily induced during the fabrication process, we expect our method to be exploited to build high-performance organic devices. PMID:27040501

Suppressing molecular vibrations in organic semiconductors by inducing strain.

PubMed

Kubo, Takayoshi; Häusermann, Roger; Tsurumi, Junto; Soeda, Junshi; Okada, Yugo; Yamashita, Yu; Akamatsu, Norihisa; Shishido, Atsushi; Mitsui, Chikahiko; Okamoto, Toshihiro; Yanagisawa, Susumu; Matsui, Hiroyuki; Takeya, Jun

2016-04-04

Organic molecular semiconductors are solution processable, enabling the growth of large-area single-crystal semiconductors. Improving the performance of organic semiconductor devices by increasing the charge mobility is an ongoing quest, which calls for novel molecular and material design, and improved processing conditions. Here we show a method to increase the charge mobility in organic single-crystal field-effect transistors, by taking advantage of the inherent softness of organic semiconductors. We compress the crystal lattice uniaxially by bending the flexible devices, leading to an improved charge transport. The mobility increases from 9.7 to 16.5 cm(2) V(-1) s(-1) by 70% under 3% strain. In-depth analysis indicates that compressing the crystal structure directly restricts the vibration of the molecules, thus suppresses dynamic disorder, a unique mechanism in organic semiconductors. Since strain can be easily induced during the fabrication process, we expect our method to be exploited to build high-performance organic devices.

An application of Six Sigma methodology to turnover intentions in health care.

PubMed

Taner, Mehmet

2009-01-01

The purpose of this study is to show how the principles of Six Sigma can be applied to the high turnover problem of doctors in medical emergency services and paramedic backup. Six Sigma's define-measure-analyse-improve-control (DMAIC) is applied for reducing the turnover rate of doctors in an organisation operating in emergency services. Variables of the model are determined. Explanatory factor analysis, multiple regression, analysis of variance (ANOVA) and Gage R&R are employed for the analysis. Personal burnout/stress and dissatisfaction from salary were found to be the "vital few" variables. The organisation took a new approach by improving its initiatives to doctors' working conditions. Sigma level of the process is increased. New policy and process changes have been found to effectively decrease the incidence of turnover intentions. The improved process is gained, standardised and institutionalised. This study is one of the few papers in the literature that elaborates the turnover problem of doctors working in the emergency and paramedic backup services.

Use of advanced oxidation processes to improve the biodegradability of mature landfill leachates.

PubMed

de Morais, Josmaria Lopes; Zamora, Patricio Peralta

2005-08-31

Two advanced oxidative processes (Fe2+/H2O2/UV and H2O2/UV systems) were used for the pre-treatment of mature landfill leachate with the objective of improving its overall biodegradability, evaluated in terms of BOD5/COD ratio, up to a value compatible with biological treatment. At optimized experimental conditions (2000 mgL(-1) of H2O2 and 10 mgL(-1) of Fe2+ for the photo-Fenton system, and 3000 mgL(-1) of H2O2 for the H2O2/UV system), both methods showed suitability for partial removal of chemical oxygen demand (COD), total organic carbon (TOC) and color. The biodegradability was significantly improved (BOD5/COD from 0.13 to 0.37 or 0.42) which allowed an almost total removal of COD and color by a sequential activated sludge process. In addition, gel permeation chromatography (GPC) has showed a substantial agreement on the cleavage of large organic compound into smaller ones.

Sex differences in cerebellar mechanisms involved in pain-related safety learning.

PubMed

Labrenz, Franziska; Icenhour, Adriane; Thürling, Markus; Schlamann, Marc; Forsting, Michael; Timmann, Dagmar; Elsenbruch, Sigrid

2015-09-01

Recent studies have suggested that the cerebellum contributes to the central processing of pain, including pain-related learning and memory processes. As a complex experience with multiple emotional and cognitive facets, the response to pain and its underlying neural correlates differ between men and women. However, it remains poorly understood whether and to what extent sex differences exist in the cerebellar contribution to pain-related associative learning processes. In the present conditioning study with experimental abdominal pain as unconditioned stimuli (US), we assessed sex-dependent differences in behavioral and neural responses to conditioned warning and safety cues in healthy volunteers. The results revealed that in response to visual stimuli signaling safety from abdominal pain (CS(-)), women showed enhanced cerebellar activation in lobules I-IV, V, VI, VIIIa, IX and X as well as Crus II and the dentate nucleus, which are mostly representative of somatomotor networks. On the other hand, men showed enhanced neural activation in lobules I-IV, VI, VIIb, VIIIb, IX as well as Crus I and II in response to CS(-), which are representative of frontoparietal and ventral attention networks. No sex differences were observed in response to pain-predictive warning signals (CS(+)). Similarly, men and women did not differ in behavioral measures of conditioning, including conditioned changes in CS valence and contingency awareness. Together, we could demonstrate that the cerebellum is involved in associative learning processes of conditioned anticipatory safety from pain and mediates sex differences in the underlying neural processes. Given the high prevalence of chronic pain conditions in women, these results may contribute to improve our understanding of the acquisition and manifestation of chronic abdominal pain syndromes. Copyright © 2015 Elsevier Inc. All rights reserved.

Mindfulness Training Alters Emotional Memory Recall Compared to Active Controls: Support for an Emotional Information Processing Model of Mindfulness

PubMed Central

Roberts-Wolfe, Douglas; Sacchet, Matthew D.; Hastings, Elizabeth; Roth, Harold; Britton, Willoughby

2012-01-01

Objectives: While mindfulness-based interventions have received widespread application in both clinical and non-clinical populations, the mechanism by which mindfulness meditation improves well-being remains elusive. One possibility is that mindfulness training alters the processing of emotional information, similar to prevailing cognitive models of depression and anxiety. The aim of this study was to investigate the effects of mindfulness training on emotional information processing (i.e., memory) biases in relation to both clinical symptomatology and well-being in comparison to active control conditions. Methods: Fifty-eight university students (28 female, age = 20.1 ± 2.7 years) participated in either a 12-week course containing a “meditation laboratory” or an active control course with similar content or experiential practice laboratory format (music). Participants completed an emotional word recall task and self-report questionnaires of well-being and clinical symptoms before and after the 12-week course. Results: Meditators showed greater increases in positive word recall compared to controls [F(1, 56) = 6.6, p = 0.02]. The meditation group increased significantly more on measures of well-being [F(1, 56) = 6.6, p = 0.01], with a marginal decrease in depression and anxiety [F(1, 56) = 3.0, p = 0.09] compared to controls. Increased positive word recall was associated with increased psychological well-being (r = 0.31, p = 0.02) and decreased clinical symptoms (r = −0.29, p = 0.03). Conclusion: Mindfulness training was associated with greater improvements in processing efficiency for positively valenced stimuli than active control conditions. This change in emotional information processing was associated with improvements in psychological well-being and less depression and anxiety. These data suggest that mindfulness training may improve well-being via changes in emotional information processing. Future research with a fully randomized design will be needed to clarify the possible influence of self-selection. PMID:22347856

Enhancement of Operating Efficiency Of The Central Coal-Preparation Plant of "MMK - UGOL" Ltd. Under Current Conditions

NASA Astrophysics Data System (ADS)

Basarygin, Maksim

2017-11-01

In this article the subject of enhancement of operating efficiency of the central coal-preparation plant of OOO "MMK-UGOL" is encompassed. Modern trends in the development of technologies and equipment for coal beneficiation are due to the following requirements: improving competitiveness of coal products, improvement of quality of marketable products, reduction of coal production cost, environmental requirements: polluting emission abatement, prepared coal saving, improvement of the effectiveness of resource conservation; complex mechanization and beneficiation process automation. In the article the contemporary problems of raw coal benefication under current conditions of the increased dilution of withdrawable coals with rock fractions are considered. Comparative analysis of efficiency of application of modern concentrating equipment under the conditions of the CCPP of OOO "MMK-UGOL" is carried out on the basis of research works. Particular attention is paid to dehydration of produced coal concentrate with content of volatile agents of more than 35.0% and content of fine-dispersed particles in flotation concentrate of more than 50.0%. Comparative analysis of the coal concentrate dehydration technologies is conducted.

NASA Astrophysics Data System (ADS)

Sampath, S.; Wayne, S. F.

1994-09-01

Thermally sprayed molybdenum coatings are used in a variety of industrial applications, such as auto-motive piston rings, aeroturbine engines, and paper and plastics processing machinery. Molybdenum ex-hibits excellent scuffing resistance under sliding contact conditions. However, plasma-sprayed molybde-num coatings are relatively soft and require dispersion strengthening (e.g., Mo2C) or addition of a second phase (e.g., NiCrBSi) to improve hardness, wear resistance, and thus coating performance. In this study, Mo-Mo2C composite powders were plasma sprayed onto mild steel substrates. Considerable decarburi-zation was observed during air plasma spraying—a beneficial condition because carbon acts as a sacrifi-cial getter for the oxygen, thereby reducing the oxide content in the coating. Finer powders showed a greater degree of decarburization due to the increased surface area; however, the starting carbide con-tent in the powder exerted very little influence on the extent of decarburization. The friction properties of Mo-Mo2C coatings were significantly improved compared to those of pure molybdenum under con-tinuous sliding contact conditions. It also was found that the abrasion resistance of the coatings improved with increasing carbide addition.

Coding strategies for cochlear implants under adverse environments

NASA Astrophysics Data System (ADS)

Tahmina, Qudsia

Cochlear implants are electronic prosthetic devices that restores partial hearing in patients with severe to profound hearing loss. Although most coding strategies have significantly improved the perception of speech in quite listening conditions, there remains limitations on speech perception under adverse environments such as in background noise, reverberation and band-limited channels, and we propose strategies that improve the intelligibility of speech transmitted over the telephone networks, reverberated speech and speech in the presence of background noise. For telephone processed speech, we propose to examine the effects of adding low-frequency and high- frequency information to the band-limited telephone speech. Four listening conditions were designed to simulate the receiving frequency characteristics of telephone handsets. Results indicated improvement in cochlear implant and bimodal listening when telephone speech was augmented with high frequency information and therefore this study provides support for design of algorithms to extend the bandwidth towards higher frequencies. The results also indicated added benefit from hearing aids for bimodal listeners in all four types of listening conditions. Speech understanding in acoustically reverberant environments is always a difficult task for hearing impaired listeners. Reverberated sounds consists of direct sound, early reflections and late reflections. Late reflections are known to be detrimental to speech intelligibility. In this study, we propose a reverberation suppression strategy based on spectral subtraction to suppress the reverberant energies from late reflections. Results from listening tests for two reverberant conditions (RT60 = 0.3s and 1.0s) indicated significant improvement when stimuli was processed with SS strategy. The proposed strategy operates with little to no prior information on the signal and the room characteristics and therefore, can potentially be implemented in real-time CI speech processors. For speech in background noise, we propose a mechanism underlying the contribution of harmonics to the benefit of electroacoustic stimulations in cochlear implants. The proposed strategy is based on harmonic modeling and uses synthesis driven approach to synthesize the harmonics in voiced segments of speech. Based on objective measures, results indicated improvement in speech quality. This study warrants further work into development of algorithms to regenerate harmonics of voiced segments in the presence of noise.

Treatment of Adult Insomnia With Cognitive–Behavioral Therapy

PubMed Central

Pigeon, Wilfred R.

2015-01-01

Insomnia is a highly prevalent disorder that occurs frequently in its acute form and at a rate of approximately 10% in its chronic form. There is a high prevalence of insomnia in a variety of medical and psychiatric conditions. Cognitive–behavioral therapy (CBT) may be employed for chronic insomnia as well as for insomnia in the context of other conditions such as chronic pain conditions. In such cases, some simple adaptations to standard CBT for insomnia are useful. This article reviews the typical assessment and CBT for adult insomnia, which have substantial empirical support for its efficacy. A case illustrates the core treatment processes and demonstrates that improving sleep in the context of conditions like chronic pain can lead to better management of such conditions. PMID:20853442

Impact of AIRS Thermodynamic Profile on Regional Weather Forecast

NASA Technical Reports Server (NTRS)

Chou, Shih-Hung; Zavodsky, Brad; Jedlovee, Gary

2010-01-01

Prudent assimilation of AIRS thermodynamic profiles and quality indicators can improve initial conditions for regional weather models. AIRS-enhanced analysis has warmer and moister PBL. Forecasts with AIRS profiles are generally closer to NAM analyses than CNTL. Assimilation of AIRS leads to an overall QPF improvement in 6-h accumulated precipitation forecasts. Including AIRS profiles in assimilation process enhances the moist instability and produces stronger updrafts and a better precipitation forecast than the CNTL run.

Plasma functionalization of polycarbonaturethane to improve endothelialization--Effect of shear stress as a critical factor for biocompatibility control.

PubMed

Lukas, Karin; Thomas, Ulrich; Gessner, André; Wehner, Daniel; Schmid, Thomas; Schmid, Christof; Lehle, Karla

2016-04-01

Medical devices made of polycarbonaturethane (PCU) combine excellent mechanical properties and little biological degradation, but restricted hemocompatibility. Modifications of PCU might reduce platelet adhesion and promote stable endothelialization. PCU was modified using gas plasma treatment, binding of hydrogels, and coupling of cell-active molecules (modified heparin, anti-thrombin III (ATIII), argatroban, fibronectin, laminin-nonapeptide, peptides with integrin-binding arginine-glycine-aspartic acid (RGD) motif). Biocompatibility was verified with static and dynamic cell culture techniques. Blinded analysis focused on improvement in endothelial cell (EC) adhesion/proliferation, anti-thrombogenicity, reproducible manufacturing process, and shear stress tolerance of ECs. EC adhesion and antithrombogenicity were achieved with 9/35 modifications. Additionally, 6/9 stimulated EC proliferation and 3/6 modification processes were highly reproducible for endothelialization. The latter modifications comprised immobilization of ATIII (A), polyethyleneglycole-diamine-hydrogel (E) and polyethylenimine-hydrogel connected with modified heparin (IH). Under sheer stress, only the IH modification improved EC adhesion within the graft. However, ECs did not arrange in flow direction and cell anchorage was restricted. Despite large variation in surface modification chemistry and improved EC adhesion under static culture conditions, additional introduction of shear stress foiled promising preliminary data. Therefore, biocompatibility testing required not only static tests but also usage of physiological conditions such as shear stress in the case of vascular grafts. © The Author(s) 2016.

PROCESS OF TREATING OR FORMING AN INSOLUBLE PLUTONIUM PRECIPITATE IN THE PRESENCE OF AN ORGANIC ACTIVE AGENT

DOEpatents

Balthis, J.H.

1961-07-18

Carrier precipitation processes for the separation of plutonium from fission products are described. In a process in which an insoluble precipitate is formed in a solution containing plutonium and fission products under conditions whereby plutonium is carried by the precipitate, and the precipitate is then separated from the remaining solution, an organic surface active agent is added to the mixture of precipitate and solution prior to separation of the precipitate from the supernatant solution, thereby improving the degree of separation of the precipitate from the solution.

Pretreatment of empty fruit bunch from oil palm for fuel ethanol production and proposed biorefinery process.

PubMed

Tan, Liping; Yu, Yongcheng; Li, Xuezhi; Zhao, Jian; Qu, Yinbo; Choo, Yuen May; Loh, Soh Kheang

2013-05-01

This study evaluates the effects of some pretreatment processes to improve the enzymatic hydrolysis of oil palm empty fruit bunch (EFB) for ethanol production. The experimental results show that the bisulfite pretreatment was practical for EFB pretreatment. Moreover, the optimum pretreatment conditions of the bisulfite pretreatment (180 °C, 30 min, 8% NaHSO3, 1% H2SO4) were identified. In the experiments, a biorefinery process of EFB was proposed to produce ethanol, xylose products, and lignosulfonates. Copyright © 2012 Elsevier Ltd. All rights reserved.

Food Quality Improvement of Soy Milk Made from Short-Time Germinated Soybeans

PubMed Central

Jiang, Susu; Cai, Weixi; Xu, Baojun

2013-01-01

The objectives of this study were to develop soy milk with improved food quality and to enhance the functional attributes by incorporating short-time germination into the processing. Changes in trypsin inhibitor activity (TIA), phytic acid content and total phenolic content (TPC) in soy milk produced from soybeans germinated within 72 h were investigated to determine the optimum germination condition. Results from the present research showed significant (p < 0.05) improvement of TPC in cooked germinated soybean milk, while both the TIA and phytic acid content were decreased significantly (p < 0.05). In the subsequent evaluation on the quality attributes under the optimum germination condition, soy milk made from 28 h-germinated soybeans presented enhanced nutritional value and comparable physicochemical properties to conventional soy milk. The current approach provides a feasible and convenient way for soy-based product innovation in both household and industrial settings. PMID:28239109

Improved Conjugate Gradient Bundle Adjustment of Dunhuang Wall Painting Images

NASA Astrophysics Data System (ADS)

Hu, K.; Huang, X.; You, H.

2017-09-01

Bundle adjustment with additional parameters is identified as a critical step for precise orthoimage generation and 3D reconstruction of Dunhuang wall paintings. Due to the introduction of self-calibration parameters and quasi-planar constraints, the structure of coefficient matrix of the reduced normal equation is banded-bordered, making the solving process of bundle adjustment complex. In this paper, Conjugate Gradient Bundle Adjustment (CGBA) method is deduced by calculus of variations. A preconditioning method based on improved incomplete Cholesky factorization is adopt to reduce the condition number of coefficient matrix, as well as to accelerate the iteration rate of CGBA. Both theoretical analysis and experimental results comparison with conventional method indicate that, the proposed method can effectively conquer the ill-conditioned problem of normal equation and improve the calculation efficiency of bundle adjustment with additional parameters considerably, while maintaining the actual accuracy.

Eco-friendly surface modification on polyester fabrics by esterase treatment

NASA Astrophysics Data System (ADS)

Wu, Jindan; Cai, Guoqiang; Liu, Jinqiang; Ge, Huayun; Wang, Jiping

2014-03-01

Currently, traditional alkali deweighting technology is widely used to improve the hydrophilicity of polyester fabrics. However, the wastewater and heavy chemicals in the effluent cause enormous damage to the environment. Esterase treatment, which is feasible in mild conditions with high selectivity, can provide a clean and efficient way for polyester modification. Under the optimum conditions, the polyester fabric hydrolysis process of esterase had a linear kinetics. X-ray photoelectron spectrometry (XPS) results showed that hydroxyl and carboxyl groups were produced only on the surface of modified fiber without changing the chemical composition of the bulk. These fibers exhibited much improved fabric wicking, as well as greatly improved oily stain removal performance. Compared to the harsh alkali hydrolysis, the enzyme treatment led to smaller weight loss and better fiber integrity. The esterase treatment technology is promising to produce higher-quality polyester textiles with an environmental friendly approach.

Toolpath strategy for cutter life improvement in plunge milling of AISI H13 tool steel

NASA Astrophysics Data System (ADS)

Adesta, E. Y. T.; Avicenna; hilmy, I.; Daud, M. R. H. C.

2018-01-01

Machinability of AISI H13 tool steel is a prominent issue since the material has the characteristics of high hardenability, excellent wear resistance, and hot toughness. A method of improving cutter life of AISI H13 tool steel plunge milling by alternating the toolpath and cutting conditions is proposed. Taguchi orthogonal array with L9 (3^4) resolution will be employed with one categorical factor of toolpath strategy (TS) and three numeric factors of cutting speed (Vc), radial depth of cut (ae ), and chip load (fz ). It is expected that there are significant differences for each application of toolpath strategy and each cutting condition factor toward the cutting force and tool wear mechanism of the machining process, and medial axis transform toolpath could provide a better tool life improvement by a reduction of cutting force during machining.

Following your heart or your head: focusing on emotions versus information differentially influences the decisions of younger and older adults.

PubMed

Mikels, Joseph A; Löckenhoff, Corinna E; Maglio, Sam J; Goldstein, Mary K; Garber, Alan; Carstensen, Laura L

2010-03-01

Research on aging has indicated that whereas deliberative cognitive processes decline with age, emotional processes are relatively spared. To examine the implications of these divergent trajectories in the context of health care choices, we investigated whether instructional manipulations emphasizing a focus on feelings or details would have differential effects on decision quality among younger and older adults. We presented 60 younger and 60 older adults with health care choices that required them to hold in mind and consider multiple pieces of information. Instructional manipulations in the emotion-focus condition asked participants to focus on their emotional reactions to the options, report their feelings about the options, and then make a choice. In the information-focus condition, participants were instructed to focus on the specific attributes, report the details about the options, and then make a choice. In a control condition, no directives were given. Manipulation checks indicated that the instructions were successful in eliciting different modes of processing. Decision quality data indicate that younger adults performed better in the information-focus than in the control condition whereas older adults performed better in the emotion-focus and control conditions than in the information-focus condition. Findings support and extend extant theorizing on aging and decision making as well as suggest that interventions to improve decision-making quality should take the age of the decision maker into account.

Nonlinear optimization method of ship floating condition calculation in wave based on vector

NASA Astrophysics Data System (ADS)

Ding, Ning; Yu, Jian-xing

2014-08-01

Ship floating condition in regular waves is calculated. New equations controlling any ship's floating condition are proposed by use of the vector operation. This form is a nonlinear optimization problem which can be solved using the penalty function method with constant coefficients. And the solving process is accelerated by dichotomy. During the solving process, the ship's displacement and buoyant centre have been calculated by the integration of the ship surface according to the waterline. The ship surface is described using an accumulative chord length theory in order to determine the displacement, the buoyancy center and the waterline. The draught forming the waterline at each station can be found out by calculating the intersection of the ship surface and the wave surface. The results of an example indicate that this method is exact and efficient. It can calculate the ship floating condition in regular waves as well as simplify the calculation and improve the computational efficiency and the precision of results.

Neural Processing of Musical and Vocal Emotions Through Cochlear Implants Simulation.

PubMed

Ahmed, Duha G; Paquette, Sebastian; Zeitouni, Anthony; Lehmann, Alexandre

2018-05-01

Cochlear implants (CIs) partially restore the sense of hearing in the deaf. However, the ability to recognize emotions in speech and music is reduced due to the implant's electrical signal limitations and the patient's altered neural pathways. Electrophysiological correlations of these limitations are not yet well established. Here we aimed to characterize the effect of CIs on auditory emotion processing and, for the first time, directly compare vocal and musical emotion processing through a CI-simulator. We recorded 16 normal hearing participants' electroencephalographic activity while listening to vocal and musical emotional bursts in their original form and in a degraded (CI-simulated) condition. We found prolonged P50 latency and reduced N100-P200 complex amplitude in the CI-simulated condition. This points to a limitation in encoding sound signals processed through CI simulation. When comparing the processing of vocal and musical bursts, we found a delay in latency with the musical bursts compared to the vocal bursts in both conditions (original and CI-simulated). This suggests that despite the cochlear implants' limitations, the auditory cortex can distinguish between vocal and musical stimuli. In addition, it adds to the literature supporting the complexity of musical emotion. Replicating this study with actual CI users might lead to characterizing emotional processing in CI users and could ultimately help develop optimal rehabilitation programs or device processing strategies to improve CI users' quality of life.

Study on Low Illumination Simultaneous Polarization Image Registration Based on Improved SURF Algorithm

NASA Astrophysics Data System (ADS)

Zhang, Wanjun; Yang, Xu

2017-12-01

Registration of simultaneous polarization images is the premise of subsequent image fusion operations. However, in the process of shooting all-weather, the polarized camera exposure time need to be kept unchanged, sometimes polarization images under low illumination conditions due to too dark result in SURF algorithm can not extract feature points, thus unable to complete the registration, therefore this paper proposes an improved SURF algorithm. Firstly, the luminance operator is used to improve overall brightness of low illumination image, and then create integral image, using Hession matrix to extract the points of interest to get the main direction of characteristic points, calculate Haar wavelet response in X and Y directions to get the SURF descriptor information, then use the RANSAC function to make precise matching, the function can eliminate wrong matching points and improve accuracy rate. And finally resume the brightness of the polarized image after registration, the effect of the polarized image is not affected. Results show that the improved SURF algorithm can be applied well under low illumination conditions.

Statistical prediction with Kanerva's sparse distributed memory

NASA Technical Reports Server (NTRS)

Rogers, David

1989-01-01

A new viewpoint of the processing performed by Kanerva's sparse distributed memory (SDM) is presented. In conditions of near- or over-capacity, where the associative-memory behavior of the model breaks down, the processing performed by the model can be interpreted as that of a statistical predictor. Mathematical results are presented which serve as the framework for a new statistical viewpoint of sparse distributed memory and for which the standard formulation of SDM is a special case. This viewpoint suggests possible enhancements to the SDM model, including a procedure for improving the predictiveness of the system based on Holland's work with genetic algorithms, and a method for improving the capacity of SDM even when used as an associative memory.

Adaptive segmentation of cerebrovascular tree in time-of-flight magnetic resonance angiography.

PubMed

Hao, J T; Li, M L; Tang, F L

2008-01-01

Accurate segmentation of the human vasculature is an important prerequisite for a number of clinical procedures, such as diagnosis, image-guided neurosurgery and pre-surgical planning. In this paper, an improved statistical approach to extracting whole cerebrovascular tree in time-of-flight magnetic resonance angiography is proposed. Firstly, in order to get a more accurate segmentation result, a localized observation model is proposed instead of defining the observation model over the entire dataset. Secondly, for the binary segmentation, an improved Iterative Conditional Model (ICM) algorithm is presented to accelerate the segmentation process. The experimental results showed that the proposed algorithm can obtain more satisfactory segmentation results and save more processing time than conventional approaches, simultaneously.

Atmospheric-Pressure Plasma Jet Surface Treatment for Use in Improving Adhesion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuettner, Lindsey Ann

Atmospheric-pressure plasma jets (APPJs) are a method of plasma treatment that plays an important role in material processing and modifying surface properties of materials, especially polymers. Gas plasmas react with polymer surfaces in numerous ways such as oxidation, radical formation, degradation, and promotion of cross-linking. Because of this, gas and plasma conditions can be explored for chosen processes to maximize desired properties. The purpose of this study is to investigate plasma parameters in order to modify surface properties for improved adhesion between aluminum and epoxy substrates using two types of adhesives. The background, results to date, and future work willmore » be discussed.« less

IMPLICATIONS OF GLOBAL CLIMATE CHANGE FOR NATURAL RESOURCE DAMAGE ASSESSMENT, RESTORATION, AND REHABILITATION

PubMed Central

Rohr, Jason R; Johnson, Philip; Hickey, Christopher W; Helm, Roger C; Fritz, Alyce; Brasfield, Sandra

2013-01-01

Various international and national regulations hold polluters liable for the cleanup of released hazardous substances and the restoration/rehabilitation of natural resources to preincident baseline conditions, a process often referred to as natural resource damage assessment and restoration (NRDAR). Here, we, the authors, describe how global climate change (GCC) will challenge each of the steps of NRDAR processes and offer eight recommendations to improve these processes in light of GCC. First, we call for a better understanding of the net effects of GCC and contaminants on natural resources. Second, we urge facilities and environmental managers to plan for GCC-related factors that are expected to increase the probability of contaminant releases. Third, we suggest re-evaluating definitions of baseline and reference conditions given that GCC will alter both their trajectories and variability. Fourth, we encourage long-term monitoring to improve the quantification of baseline conditions that will change as climate changes. This will enhance the accuracy of injury assessments, the effectiveness of restoration, and the detection of early warning signs that ecosystems are approaching tipping points. Fifth, in response to or anticipation of GCC, restoration projects may need to be conducted in areas distant from the site of injury or focused on functionally equivalent natural resources; thus, community involvement in NRDAR processes will be increasingly important. Sixth, we promote using NRDAR restoration projects as opportunities to mitigate GCC-related impacts. Seventh, we recommend adaptive management approaches to NRDAR processes and communication of successes and failures widely. Finally, we recommend focusing on managing the stressors that might be exacerbated by GCC, such as pollution and habitat loss, because there is a long history of successfully mitigating these stressors, which can be more easily managed on local scales than climate change. We believe that adoption of these recommendations will lead to a more efficacious NRDAR process, despite the challenges posed by climate change. Environ. Toxicol. Chem. 2013;32:93–101. © 2012 SETAC PMID:23097077

Implications of global climate change for natural resource damage assessment, restoration, and rehabilitation.

PubMed

Rohr, Jason R; Johnson, Philip; Hickey, Christopher W; Helm, Roger C; Fritz, Alyce; Brasfield, Sandra

2013-01-01

Various international and national regulations hold polluters liable for the cleanup of released hazardous substances and the restoration/rehabilitation of natural resources to preincident baseline conditions, a process often referred to as natural resource damage assessment and restoration (NRDAR). Here, we, the authors, describe how global climate change (GCC) will challenge each of the steps of NRDAR processes and offer eight recommendations to improve these processes in light of GCC. First, we call for a better understanding of the net effects of GCC and contaminants on natural resources. Second, we urge facilities and environmental managers to plan for GCC-related factors that are expected to increase the probability of contaminant releases. Third, we suggest re-evaluating definitions of baseline and reference conditions given that GCC will alter both their trajectories and variability. Fourth, we encourage long-term monitoring to improve the quantification of baseline conditions that will change as climate changes. This will enhance the accuracy of injury assessments, the effectiveness of restoration, and the detection of early warning signs that ecosystems are approaching tipping points. Fifth, in response to or anticipation of GCC, restoration projects may need to be conducted in areas distant from the site of injury or focused on functionally equivalent natural resources; thus, community involvement in NRDAR processes will be increasingly important. Sixth, we promote using NRDAR restoration projects as opportunities to mitigate GCC-related impacts. Seventh, we recommend adaptive management approaches to NRDAR processes and communication of successes and failures widely. Finally, we recommend focusing on managing the stressors that might be exacerbated by GCC, such as pollution and habitat loss, because there is a long history of successfully mitigating these stressors, which can be more easily managed on local scales than climate change. We believe that adoption of these recommendations will lead to a more efficacious NRDAR process, despite the challenges posed by climate change. Copyright © 2012 SETAC.

Optimization of Coolant Technique Conditions for Machining A319 Aluminium Alloy Using Response Surface Method (RSM)

NASA Astrophysics Data System (ADS)

Zainal Ariffin, S.; Razlan, A.; Ali, M. Mohd; Efendee, A. M.; Rahman, M. M.

2018-03-01

Background/Objectives: The paper discusses about the optimum cutting parameters with coolant techniques condition (1.0 mm nozzle orifice, wet and dry) to optimize surface roughness, temperature and tool wear in the machining process based on the selected setting parameters. The selected cutting parameters for this study were the cutting speed, feed rate, depth of cut and coolant techniques condition. Methods/Statistical Analysis Experiments were conducted and investigated based on Design of Experiment (DOE) with Response Surface Method. The research of the aggressive machining process on aluminum alloy (A319) for automotive applications is an effort to understand the machining concept, which widely used in a variety of manufacturing industries especially in the automotive industry. Findings: The results show that the dominant failure mode is the surface roughness, temperature and tool wear when using 1.0 mm nozzle orifice, increases during machining and also can be alternative minimize built up edge of the A319. The exploration for surface roughness, productivity and the optimization of cutting speed in the technical and commercial aspects of the manufacturing processes of A319 are discussed in automotive components industries for further work Applications/Improvements: The research result also beneficial in minimizing the costs incurred and improving productivity of manufacturing firms. According to the mathematical model and equations, generated by CCD based RSM, experiments were performed and cutting coolant condition technique using size nozzle can reduces tool wear, surface roughness and temperature was obtained. Results have been analyzed and optimization has been carried out for selecting cutting parameters, shows that the effectiveness and efficiency of the system can be identified and helps to solve potential problems.

Growth performance, survival, and processing characteristics of hybrid catfish fed pre And probiotics

USDA-ARS?s Scientific Manuscript database

There has been a lot of interest in the use of pre and probiotics to increase growth and improve disease resistance in the catfish industry. This study aimed to evaluate a commercially available prebiotic and probiotic under conditions simulating commercial production in hybrid catfish. The dietar...

The AHA and Faculty Development.

ERIC Educational Resources Information Center

Thompson, Mack

The American Historical Association's (AHA) involvement in Faculty Development Programs (FDP) in history instruction is described. The purpose of FDP is to improve teaching as part of a continuing process. AHA guidelines recommend that these programs be initiated and supported by AHA under the following conditions: (1) a regional confederation of…

Advisory: Definitions, Descriptions, Decisions, Directions.

ERIC Educational Resources Information Center

Galassi, John P.; Gulledge, Suzanne A.; Cox, Nancy D.

Advisory groups have played an essential role in improving the school climate and conditions for young adolescents in schools. How middle school decision makers go about the process of designing or re-designing an advisory program needs to be considered. A discussion is presented of the background information that helps define advisories. It…

Pedagogical Interaction in High School, the Structural and Functional Model of Pedagogical Interaction

ERIC Educational Resources Information Center

Semenova, Larissa A.; Kazantseva, Anastassiya I.; Sergeyeva, Valeriya V.; Raklova, Yekaterina M.; Baiseitova, Zhanar B.

2016-01-01

The study covers the problems of pedagogical technologies and their experimental implementation in the learning process. The theoretical aspects of the "student-teacher" interaction are investigated. A structural and functional model of pedagogical interaction is offered, which determines the conditions for improving pedagogical…

Protocols for vegetation and habitat monitoring with unmanned aerial vehicles: linking research to management on US public lands

USDA-ARS?s Scientific Manuscript database

Background/Question/Methods: Monitoring of the condition and trend of natural resources is critical for determining effectiveness of management actions and understanding ecosystem responses to broad-scale processes like climate change. While broad-scale remote sensing has generally improved the abi...

Social acceptability of forest conditions and management practices: a problem analysis.

Treesearch

Bruce A. Shindler; Mark Brunson; George H. Stankey

2002-01-01

The purpose of this report is to improve understanding of the complex sociopolitical processes related to resource management and to help structure management response to conflict and contentiousness, misunderstanding among participants, and failed citizen-agency interactions. Public acceptance is essential to every resource management decision public agencies must...

Working with Slow Readers, Slow Learners.

ERIC Educational Resources Information Center

Smith, Carl B.

1990-01-01

This article examines the conditions that will help teachers improve the reading comprehension of learning disabled students: (1) allow more time; (2) build a framework for comprehension; (3) intervene in the process; (4) engage the learner; (5) match student and material; and (6) expect students to succeed. Two figures are included. (RS)

Learning for Maximum Impact: Four Critical but Overlooked Ideas

ERIC Educational Resources Information Center

Roberson, Sam

2017-01-01

Thinking and learning are corresponding and interdependent processes in every classroom. To improve learning, teachers must be open to new ideas, particularly ideas that locate conditions for maximum learning. This paper presents four overlooked but critical ideas that identify a common area, a GAP experience within which maximum learning is…

Improving Electrode Durability of PEF Chamber by selecting suitable material

USDA-ARS?s Scientific Manuscript database

Corrosion resistance of four materials - titanium, platinized titanium, stainless steel, and boron carbide - as electrodes in a Pulsed Electric Field (PEF) system was studied to reduce electrode material migration into the food by electrode corrosion. The PEF process conditions were 28 kV/cm field s...

Integrating Strategic Planning Concepts into the Negotiating Process.

ERIC Educational Resources Information Center

Winer, Toby R.; Winer, Russell S.

1987-01-01

The purchase of a new telecommunications system at Vanderbilt University is described. By understanding conditions in which buyers generally obtain leverage over sellers in industries, it was possible to improve negotiating power. Strategic-planning concepts developed by Michael Porter in his book "Competitive Strategy" were used as a…

Simulating and Optimizing Preparative Protein Chromatography with ChromX

ERIC Educational Resources Information Center

Hahn, Tobias; Huuk, Thiemo; Heuveline, Vincent; Hubbuch, Ju¨rgen

2015-01-01

Industrial purification of biomolecules is commonly based on a sequence of chromatographic processes, which are adapted slightly to new target components, as the time to market is crucial. To improve time and material efficiency, modeling is increasingly used to determine optimal operating conditions, thus providing new challenges for current and…

Pharmacological Approaches to Performance Enhancement in Animals,

DTIC Science & Technology

found to improve performance disrupted by exposure to hypoxia. These substances included piracetam , nimodipine, and ipsapirone. An additional...their low toxicity , and their lack of negative effects on normal cognitive performance, it is suggested that these drugs could prove to be useful therapeutic agents under conditions of high information processing load.

The Role of the Universities in the Current Scientific and Technological Revolution in the USSR

ERIC Educational Resources Information Center

Nuzhin, M. T.

1975-01-01

The scientific and technological revolution is making progressive changes in the material conditions of economic production in Russia and is actively influencing the development and improvement of education. The influence of university education on the socioeconomic process is discussed. (Author/RM)

The Principal as Change Agent--Encouraging Teachers to Adopt Change.

ERIC Educational Resources Information Center

Aquila, Frank D.; Galovic, John

1988-01-01

Principals as change agents must work with teachers to establish a climate conducive to change. Principals should assume an assertive change posture and improve their skills in dealing with various factors influencing change. Teacher discontent with working conditions is a key ingredient in the change process. (MLH)

Green dyeing process of modified cotton fibres using natural dyes extracted from Tamarix aphylla (L.) Karst. leaves.

PubMed

Baaka, Noureddine; Mahfoudhi, Adel; Haddar, Wafa; Mhenni, Mohamed Farouk; Mighri, Zine

2017-01-01

This research work involves an eco-friendly dyeing process of modified cotton with the aqueous extract of Tamarix aphylla leaves. During this process, the dyeing step was carried out on modified cotton by several cationising agents in order to improve its dyeability. The influence of the main dyeing conditions (dye bath pH, dyeing time, dyeing temperature, salt addition) on the performances of this dyeing process were studied. The dyeing performances of this process were appreciated by measuring the colour yield (K/S) and the fastness properties of the dyed samples. The effect of mordant type with different mordanting methods on dyeing quality was also studied. The results showed that mordanting gave deeper shades and enhanced fastness properties. In addition, environmental indicators (BOD 5 , COD and COD/BOD 5 ) were used to describe potential improvements in the biodegradability of the dyebath wastewater. Further, HPLC was used to identify the major phenolic compounds in the extracted dye.

The effect of material productivity on scrap reduction on aluminum reduction pot process

NASA Astrophysics Data System (ADS)

Huda, L. N.

2018-02-01

Scrap in the production process is defined as part of production that can not be accepted as the final product due to production failure. The amount of scarp occurring in the reduction pot production process of one of the aluminum smelting furnaces exceeds the acceptance standard of 5 to 10%. This affects the amount of production produced. The purpose of this study is to reduce the amount of scrap produced to increase the productivity of the materials used. The solution is carried-out by making improvements using Lean Six Sigma method. In the initial calculation, material productivity ranged from 0.88. Based on the study, the factors that cause the high amount of scrap produced is the use of Na2O which is inserted into the alumina is different in size and the influence of noise that occurs in pots that are difficult to control. The analysis base on Lean Six Sigma obtained process cycle efficiency (PCE) equal to 86,92% for actual condition. Process improvement is carried-out through define, measure, analyze, improve and control procedure on Na2O feeding process and PCE value decrease 6,05%. This indicates that increased process capability will reduce scrap. A decrease in scrap amount of about 6% will be able to increase material productivity by 0.05%. This indicates that continuous process control is needed to decrease the number of scraps and increase productivity.

Pre-processing by data augmentation for improved ellipse fitting.

PubMed

Kumar, Pankaj; Belchamber, Erika R; Miklavcic, Stanley J

2018-01-01

Ellipse fitting is a highly researched and mature topic. Surprisingly, however, no existing method has thus far considered the data point eccentricity in its ellipse fitting procedure. Here, we introduce the concept of eccentricity of a data point, in analogy with the idea of ellipse eccentricity. We then show empirically that, irrespective of ellipse fitting method used, the root mean square error (RMSE) of a fit increases with the eccentricity of the data point set. The main contribution of the paper is based on the hypothesis that if the data point set were pre-processed to strategically add additional data points in regions of high eccentricity, then the quality of a fit could be improved. Conditional validity of this hypothesis is demonstrated mathematically using a model scenario. Based on this confirmation we propose an algorithm that pre-processes the data so that data points with high eccentricity are replicated. The improvement of ellipse fitting is then demonstrated empirically in real-world application of 3D reconstruction of a plant root system for phenotypic analysis. The degree of improvement for different underlying ellipse fitting methods as a function of data noise level is also analysed. We show that almost every method tested, irrespective of whether it minimizes algebraic error or geometric error, shows improvement in the fit following data augmentation using the proposed pre-processing algorithm.

Research on Construction Technology of First Pile in an Urban Expressway under Complicated Conditions

NASA Astrophysics Data System (ADS)

Zhu, Zhi gang

2017-12-01

This paper develops a research method on the construction of the first pile in the process of the construction on an urban expressway under complicated conditions, such as the difference between the underground conditions and the exploration results,the sand formation,the whole weathered and the rich groundwater. We study the relevant technical parameters and construction organization through construction of the first pile. The results show that construction on the first pile is very important under complicated conditions and can provide a basis to continuously improve the level of the whole pile foundation construction technology, and ultimately determine the entire project feasible construction program and the successful completion of the construction project.

Spatial Visualization ability improves with and without studying Technical Drawing.

PubMed

Contreras, María José; Escrig, Rebeca; Prieto, Gerardo; Elosúa, M Rosa

2018-03-27

The results of several studies suggest that spatial ability can be improved through direct training with tasks similar to those integrated in the tests used to measure the ability. However, there is a greater interest in analyzing the effectiveness of indirect training such as games or of learning subjects that involve spatial processes to a certain extent. Thus, the objective of the present study was to analyze whether the indirect training in Technical Drawing improved the Spatial Visualization ability of Architecture students. For this purpose, a group of students enrolled in Fundamentals of Architecture were administered two tests, a Spatial Visualization task and an Abstract Reasoning task, at the beginning and the end of a semester, after having received training through the subjects "Technical Drawing I: Geometry and Perception" and "Projects I." The results of this group were compared with those of a control group of students enrolled in a Mathematics degree, who were also pre-post evaluated but had not received the training in Technical Drawing. The study showed a significant pre-post improvement in both, Visualization and reasoning. However, this improvement occurred in both groups, thereby concluding that this improvement was not due to indirect training. Furthermore, no significant differences were found between men and women in any of the groups or conditions. These results clarify those of an earlier study where improvement in Visualization after training in Technical Drawing was found but did not include a comparison with a control condition. The control condition has proved to be important in order to consider the limitations of the effect of Technical Drawing on said improvement.

Energy, cost and design aspects of coarse- and fine-bubble aeration systems in the MBBR IFAS process.

PubMed

Sander, S; Behnisch, J; Wagner, M

2017-02-01

With the MBBR IFAS (moving bed biofilm reactor integrated fixed-film activated sludge) process, the biomass required for biological wastewater treatment is either suspended or fixed on free-moving plastic carriers in the reactor. Coarse- or fine-bubble aeration systems are used in the MBBR IFAS process. In this study, the oxygen transfer efficiency (OTE) of a coarse-bubble aeration system was improved significantly by the addition of the investigated carriers, even in-process (∼1% per vol-% of added carrier material). In a fine-bubble aeration system, the carriers had little or no effect on OTE. The effect of carriers on OTE strongly depends on the properties of the aeration system, the volumetric filling rate of the carriers, the properties of the carrier media, and the reactor geometry. This study shows that the effect of carriers on OTE is less pronounced in-process compared to clean water conditions. When designing new carriers in order to improve their effect on OTE further, suppliers should take this into account. Although the energy efficiency and cost effectiveness of coarse-bubble aeration systems can be improved significantly by the addition of carriers, fine-bubble aeration systems remain the more efficient and cost-effective alternative for aeration when applying the investigated MBBR IFAS process.

Chronic oedema: its prevalence, effects and management.

PubMed

Cooper, Garry

2016-10-01

Ageing affects not only individuals but also society. It occurs throughout the western world. The ageing process may lead to the development of conditions, such as chronic oedema, as well as comorbidities such as osteoarthritis. These comorbidities can make the management of chronic oedema even more difficult. This is an especially important consideration when tailoring individualised care plans, such as exercise, as conditions such as rheumatoid arthritis can limit patients' ability to manage their oedema. Despite challenges, education can improve patient outcomes when evidence-based practice is used.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kafka, Kyle R. P.; Hoffman, Brittany N.; Papernov, Semyon

The laser-induced damage threshold of fused-silica samples processed via magnetorheological finishing is investigated for polishing compounds depending on the type of abrasive material and the post-polishing surface roughness. The effectiveness of laser conditioning is examined using a ramped pre-exposure with the same 351-nm, 3-ns Gaussian pulses. Lastly, we examine chemical etching of the surface and correlate the resulting damage threshold to the etching protocol. A combination of etching and laser conditioning is found to improve the damage threshold by a factor of ~3, while maintaining <1-nm surface roughness.

Constitutional and acquired autosomal aneuploidy.

PubMed

Jackson-Cook, Colleen

2011-12-01

Chromosomal imbalances can result from numerical or structural anomalies. Numerical chromosomal abnormalities are often referred to as aneuploid conditions. This article focuses on the occurrence of constitutional and acquired autosomal aneuploidy in humans. Topics covered include frequency, mosaicism, phenotypic findings, and etiology. The article concludes with a consideration of anticipated advances that might allow for the development of screening tests and/or lead to improvements in our understanding and management of the role that aneuploidy plays in the aging process and acquisition of age-related and constitutional conditions.

Giving them a good start: informatics support of newborn screening and clinical care.

PubMed

Wetter, T; Haschler, I; Ho, S; Hoffmann, G F; Linderkamp, O; Philipp, F; Skonetzki, S

2005-01-01

Newborns are a vulnerable population: Exposed to dramatically changing environmental conditions, potentially suffering from impairments that cannot realistically be diagnosed during pregnancy, with the risk that unfavorable conditions escalate fast. We have investigated informatics methods and tools to make screening for congenital diseases and containment of critical processes that start in the first days safer and more efficient. This poster present a set of three different methodological approaches that all aim at comprehensive improvement of neonatal care.

Process for preparing metal-carbide-containing microspheres from metal-loaded resin beads

DOEpatents

Beatty, Ronald L.

1976-01-01

An improved method for treating metal-loaded resin microspheres is described which comprises heating a metal-loaded resin charge in an inert atmosphere at a pre-carbide-forming temperature under such conditions as to produce a microsphere composition having sufficient carbon as to create a substantially continuous carbon matrix and a metal-carbide or an oxide-carbide mixture as a dispersed phase(s) during carbide-forming conditions, and then heating the thus treated charge to a carbide-forming temperature.