Poly β-hydroxybutyrate production by Bacillus subtilis NG220 using sugar industry waste water.

PubMed

Singh, Gulab; Kumari, Anish; Mittal, Arpana; Yadav, Anita; Aggarwal, Neeraj K

2013-01-01

The production of poly β-hydroxybutyrate (PHB) by Bacillus subtilis NG220 was observed utilizing the sugar industry waste water supplemented with various carbon and nitrogen sources. At a growth rate of 0.14 g h(-1) L(-1), using sugar industry waste water was supplemented with maltose (1% w/v) and ammonium sulphate (1% w/v); the isolate produced 5.297 g/L of poly β-hydroxybutyrate accumulating 51.8% (w/w) of biomass. The chemical nature of the polymer was confirmed with nuclear magnetic resonance, Fourier transform infrared, and GC-MS spectroscopy whereas thermal properties were monitored with differential scanning calorimetry. In biodegradability study, when PHB film of the polymer (made by traditional solvent casting technique) was subjected to degradation in various natural habitats like soil, compost, and industrial sludge, it was completely degraded after 30 days in the compost having 25% (w/w) moisture. So, the present study gives insight into dual benefits of conversion of a waste material into value added product, PHB, and waste management.

Poly β-Hydroxybutyrate Production by Bacillus subtilis NG220 Using Sugar Industry Waste Water

PubMed Central

Singh, Gulab; Kumari, Anish; Mittal, Arpana; Yadav, Anita; Aggarwal, Neeraj K.

2013-01-01

The production of poly β-hydroxybutyrate (PHB) by Bacillus subtilis NG220 was observed utilizing the sugar industry waste water supplemented with various carbon and nitrogen sources. At a growth rate of 0.14 g h−1 L−1, using sugar industry waste water was supplemented with maltose (1% w/v) and ammonium sulphate (1% w/v); the isolate produced 5.297 g/L of poly β-hydroxybutyrate accumulating 51.8% (w/w) of biomass. The chemical nature of the polymer was confirmed with nuclear magnetic resonance, Fourier transform infrared, and GC-MS spectroscopy whereas thermal properties were monitored with differential scanning calorimetry. In biodegradability study, when PHB film of the polymer (made by traditional solvent casting technique) was subjected to degradation in various natural habitats like soil, compost, and industrial sludge, it was completely degraded after 30 days in the compost having 25% (w/w) moisture. So, the present study gives insight into dual benefits of conversion of a waste material into value added product, PHB, and waste management. PMID:24027767

Environmental cost and pollution risk caused by the industrial transfer in Qinghai Province

NASA Astrophysics Data System (ADS)

Jiang, Qun'ou; Tang, Chengcai; Zhan, Jinyan; Zhang, Wei; Wu, Feng

2014-09-01

With the rising pressure due to energy consumption and costs of environmental protection and recovery, industrial transfer from the eastern to central and western areas has surged in China. However, extremely fragile ecological conditions and severe water shortage are significant hurdles for industry development in Western China. Whether the vulnerable environment can bear the pollution caused by the transferred industry from Eastern China becomes a significant issue. This study firstly estimates energy and environmental costs in different areas of China, and assesses the necessity to upgrade the industrial structure of Qinghai Province. Then the emissions of waste water, waste gas, and smoke caused by transferred industries are calculated by Input-Output Model. On the basis of the effect analysis of waste emission on environment, pollution risks of Qinghai province are assessed. The results illustrate that the costs of environmental protection and recovery in China have a gradient distribution, of which the energy efficiency is lower while environmental costs are higher in Western China. Industrial structure adjustment has different impacts on the pollution of different sectors. Although the development of machinery and equipment, hotels and catering services, and real estate, leasing, and business services has increased the emission of pollutants, it is offset by the decreasing emissions caused by other industries such as construction and metal products. Therefore, although economic development will increase environmental pollution, industrial adjustments can effectively decrease waste water and waste gas emissions to reduce the pollution risk. It should be noted that there are still tremendous challenges for industrial transfer in Qinghai Province to coordinate the environment and industry development.

Integration of Cleaner Production and Waste Water Treatment on Tofu Small Industry for Biogas Production using AnSBR Reactor

NASA Astrophysics Data System (ADS)

Rahayu, Suparni Setyowati; Budiyono; Purwanto

2018-02-01

A research on developing a system that integrates clean production and waste water treatment for biogas production in tofu small industry has been conducted. In this research, tofu waste water was turned into biogas using an AnSBR reactor. Mud from the sewage system serves as the inoculums. This research involved: (1) workshop; (2) supervising; (3) technical meeting; (4) network meeting, and (5) technical application. Implementation of clean production integrated with waste water treatment reduced the amount of waste water to be treated in a treatment plant. This means less cost for construction and operation of waste water treatment plants, as inherent limitations associated with such plants like lack of fund, limited area, and technological issues are inevitable. Implementation of clean production prior to waste water treatment reduces pollution figures down to certain levels that limitations in waste water treatment plants can be covered. Results show that biogas in 16 days HRT in an AnSBR reactor contains CH4(78.26 %) and CO2 (20.16 %). Meanwhile, treatments using a conventional bio-digester result in biogas with 72.16 % CH4 and 18.12 % CO2. Hence, biogas efficiency for the AnSBR system is 2.14 times greater than that of a conventional bio-digester.

Ecotoxicity of waste water from industrial fires fighting

NASA Astrophysics Data System (ADS)

Dobes, P.; Danihelka, P.; Janickova, S.; Marek, J.; Bernatikova, S.; Suchankova, J.; Baudisova, B.; Sikorova, L.; Soldan, P.

2012-04-01

As shown at several case studies, waste waters from extinguishing of industrial fires involving hazardous chemicals could be serious threat primary for surrounding environmental compartments (e.g. surface water, underground water, soil) and secondary for human beings, animals and plants. The negative impacts of the fire waters on the environment attracted public attention since the chemical accident in the Sandoz (Schweizerhalle) in November 1986 and this process continues. Last October, special Seminary on this topic has been organized by UNECE in Bonn. Mode of interaction of fire waters with the environment and potential transport mechanisms are still discussed. However, in many cases waste water polluted by extinguishing foam (always with high COD values), flammable or toxic dangerous substances as heavy metals, pesticides or POPs, are released to surface water or soil without proper decontamination, which can lead to environmental accident. For better understanding of this type of hazard and better coordination of firemen brigades and other responders, the ecotoxicity of such type of waste water should be evaluated in both laboratory tests and in water samples collected during real cases of industrial fires. Case studies, theoretical analysis of problem and toxicity tests on laboratory model samples (e.g. on bacteria, mustard seeds, daphnia and fishes) will provide additional necessary information. Preliminary analysis of waters from industrial fires (polymer material storage and galvanic plating facility) in the Czech Republic has already confirmed high toxicity. In first case the toxicity may be attributed to decomposition of burned material and extinguishing foams, in the latter case it can be related to cyanides in original electroplating baths. On the beginning of the year 2012, two years R&D project focused on reduction of extinguish waste water risk for the environment, was approved by Technology Agency of the Czech Republic.

Effect of fermentation time of mixture of solid and liquid wastes from tapioca industry to percentage reduction of TSS (Total Suspended Solids)

NASA Astrophysics Data System (ADS)

Pandia, S.; Tanata, S.; Rachel, M.; Octiva, C.; Sialagan, N.

2018-02-01

The waste from tapioca industry is as an organic waste that contains many important compounds such as carbohydrate, protein, and glucose. This research as aimed to know the effect of fermentation time from solid waste combined with waste-water from the tapioca industry to percentage reduction of TSS. The study was started by mixing the solid and liquid wastes from tapioca industry at a ratio of 70:30, 60:40, 50:50, 40:60, and 30:70 (w/w) with a starter from solid waste of cattle in a batch anaerobic digester. The percentage reduction of TSS was 72.2289 at a ratio by weight of the composition of solid and liquid wastes from tapioca industry was 70:30 after 30 days of fermentation time.

40 CFR 35.928-1 - Approval of the industrial cost recovery system.

Code of Federal Regulations, 2010 CFR

2010-07-01

... treatment works or (2) the charges to be collected by the grantee in providing waste water treatment... accepting waste-waters from other municipalities, the subscribers receiving waste treatment services from... municipalities contributing wastes to the treatment works. The public shall be consulted prior to adoption of the...

40 CFR 35.928-1 - Approval of the industrial cost recovery system.

Code of Federal Regulations, 2011 CFR

2011-07-01

... treatment works or (2) the charges to be collected by the grantee in providing waste water treatment... accepting waste-waters from other municipalities, the subscribers receiving waste treatment services from... municipalities contributing wastes to the treatment works. The public shall be consulted prior to adoption of the...

Suitability assessment of grey water quality treated with an upflow-downflow siliceous sand/marble waste filtration system for agricultural and industrial purposes.

PubMed

Chaabane, Safa; Riahi, Khalifa; Hamrouni, Hédi; Thayer, Béchir Ben

2017-04-01

The present study examines the suitability assessment of an upflow-downflow siliceous sand/marble waste filtration system for treatment and reuse of grey water collected from bathrooms of the student residential complex at the Higher Institute of Engineering Medjez El Bab (Tunisia). Once the optimization of grey water pre-treatment system has been determined, the filtration system was operated at different hydraulic loading rate and media filter proportions in order to assess the suitability of treated grey water for irrigational purpose according to salinity hazard, sodium hazard, magnesium hazard, permeability index, water infiltration rate, and widely used graphical methods. Suitability of the treated grey water for industrial purpose was evaluated in terms of foaming, corrosion, and scaling. Under optimal operational conditions, results reveals that treated grey water samples with an upflow-downflow siliceous sand/marble waste filtration system may be considered as a good and an excellent water quality suitable for irrigation purpose. However, treated grey water was found not appropriate for industrial purpose due to high concentrations of calcium and sodium that can generate foaming and scaling harm to boilers. These results suggest that treated grey water with an upflow-downflow siliceous sand/marble waste filtration system would support production when used as irrigation water.

Data on subsurface storage of liquid waste near Pensacola, Florida, 1963-1980

USGS Publications Warehouse

Hull, R.W.; Martin, J.B.

1982-01-01

Since 1963, when industrial waste was first injected into the subsurface in northwest Florida, considerable data have been collected relating to the geochemistry of subsurface waste storage. This report presents hydrogeologic data on two subsurface waste storage. This report presents hydrogeologic data on two subsurface storage systems near Pensacola, Fla., which inject liquid industrial waste through deep wells into a saline aquifer. Injection sites are described giving a history of well construction, injection, and testing; geologic data from cores and grab samples; hydrographs of injection rates, volume, pressure, and water levels; and chemical and physical data from water-quality samples collected from injection and monitor wells. (USGS)

[Shifting path of industrial pollution gravity centers and its driving mechanism in Pan-Yangtze River Delta].

PubMed

Zhao, Hai-Xia; Jiang, Xiao-Wei; Cui, Jian-Xin

2014-11-01

Shifting path of industrial pollution gravity centers is the response of environmental special formation during the industry transfer process, in order to prove the responding of industrial pollution gravity centers to industry transfer in economically developed areas, this paper calculates the gravity centers of industrial wastewater, gas and solid patterns and reveals the shifting path and its driving mechanism, using the data of industrial pollution in the Pan-Yangtze River Delta from 2000 to 2010. The results show that the gravity center of the industrial waste in Pan-Yangtze River Delta shifts for sure in the last 10 years, and gravity center of solid waste shifts the maximum distance within the three wastes, which was 180.18 km, and shifting distances for waste gas and waste water were 109.51 km and 85.92 km respectively. Moreover, the gravity center of the industrial waste in Pan-Yangtze River Delta shifts westwards, and gravity centers of waste water, gas and solid shift for 0.40 degrees, 0.17 degrees and 0.03 degrees respectively. The shifting of industrial pollution gravity centers is driven by many factors. The rapid development of the heavy industry in Anhui and Jiangxi provinces results in the westward shifting of the pollutions. The optimization and adjustment of industrial structures in Yangtze River Delta region benefit to alleviating industrial pollution, and high-polluting industries shifted to Anhui and Jiangxi provinces promotes pollution gravity center shifting to west. While the development of massive clean enterprise, strong environmental management efforts and better environmental monitoring system slow the shifting trend of industrial pollution to the east in Yangtze River Delta. The study of industrial pollution gravity shift and its driving mechanism provides a new angle of view to analyze the relationship between economic development and environmental pollution, and also provides academic basis for synthetical management and control of environmental pollution in Pan-Yangtze River Delta, especially in the transition period.

Performance of metal compound on thermolysis and electrolysis on sugar industries waste water treatment: COD and color removal with sludge analysis (batch-experiment)

NASA Astrophysics Data System (ADS)

Sahu, Omprakash

2017-10-01

The sugar cane industry is one of the most water demanding industries. Sugar industries consume and generate excess amount of water. The generated water contains organic compounds, which would cause pollution. The aim of this research work is to study the effectiveness of metal compound for treatment of sugar industry waste water by thermolysis and electrolysis process. The result shows ferrous metal catalyst shows 80 and 85 % chemical oxygen demand and color removal at pH 6, optimum mass loading 4 kg/m3, treatment temperature 85 °C and treatment time 9 h. When ferrous material was used as electrode, maximum 81 % chemical oxygen demand and 84 % color removal at pH 6, current density 156 Am-2, treatment time 120 min and anode consumption 0.7 g for 1.5 L wastewater were obtained.

Mutagenicity and cytotoxicity of liquid waste, press water and pond water, produced in the cassava flour industry, and of antitoxic sodium thiosulfate.

PubMed

Viana, Lilian Ávila; Düsman, Elisângela; Vicentini, Veronica Elisa Pimenta

2014-02-01

Cassava (Manihot esculenta Crantz), a plant used as food and an ingredient in industry, contains cyanogenic glycosides. The cassava root contains wastewater, popularly known as manipueira, which is a toxic substance. Its ingestion by animals causes poisoning although they react positively to treatment with sodium thiosulfate. The present research evaluates the cytotoxicity and the mutagenicity of liquid waste produced in the process of industrialization of the bitter cassava, olho-junto variety. The liquid wastes are characterized as press water, which is obtained when the cassava roots are pressed; pond water, which is press water stored in impounded ponds; and a solution of sodium thiosulfate, pure and with other waste. The system tests comprised root meristematic cells of Allium cepa L. and bone marrow cells of Rattus norvegicus. Treatment with saline solution was cytotoxic for Allium cepa L. and significantly reduced cell division rate. Although no treatment was cytotoxic in any of the tests with rats, the thiosulfate solution was clastogenic for the chromosomal aberrations test. Since it is harmful to the genetic material submitted within the conditions of current research, sodium thiosulfate should only be used in emergency conditions in which the benefits exceed the risks. © 2013 Society of Chemical Industry.

Photolytic AND Catalytic Destruction of Organic Waste Water Pollutants

NASA Astrophysics Data System (ADS)

Torosyan, V. F.; Torosyan, E. S.; Kryuchkova, S. O.; Gromov, V. E.

2017-01-01

The system: water supply source - potable and industrial water - wastewater - sewage treatment - water supply source is necessary for water supply and efficient utilization of water resources. Up-to-date technologies of waste water biological treatment require for special microorganisms, which are technologically complex and expensive but unable to solve all the problems. Application of photolytic and catalytically-oxidizing destruction is quite promising. However, the most reagents are strong oxidizers in catalytic oxidation of organic substances and can initiate toxic substance generation. Methodic and scientific approaches to assess bread making industry influence on the environment have been developed in this paper in order to support forecasting and taking technological decisions concerning reduction of this influence. Destructive methods have been tested: ultra violet irradiation and catalytic oxidation for extraction of organic compounds from waste water by natural reagents.

Monitoring of toxic elements present in sludge of industrial waste using CF-LIBS.

PubMed

Kumar, Rohit; Rai, Awadhesh K; Alamelu, Devanathan; Aggarwal, Suresh K

2013-01-01

Industrial waste is one of the main causes of environmental pollution. Laser-induced breakdown spectroscopy (LIBS) was applied to detect the toxic metals in the sludge of industrial waste water. Sludge on filter paper was obtained after filtering the collected waste water samples from different sections of a water treatment plant situated in an industrial area of Kanpur City. The LIBS spectra of the sludge samples were recorded in the spectral range of 200 to 500 nm by focusing the laser light on sludge. Calibration-free laser-induced breakdown spectroscopy (CF-LIBS) technique was used for the quantitative measurement of toxic elements such as Cr and Pb present in the sample. We also used the traditional calibration curve approach to quantify these elements. The results obtained from CF-LIBS are in good agreement with the results from the calibration curve approach. Thus, our results demonstrate that CF-LIBS is an appropriate technique for quantitative analysis where reference/standard samples are not available to make the calibration curve. The results of the present experiment are alarming to the people living nearby areas of industrial activities, as the concentrations of toxic elements are quite high compared to the admissible limits of these substances.

Laboratory measurements of radiance and reflectance spectra of a dilute biosolid industrial waste product

NASA Technical Reports Server (NTRS)

Usry, J. W.; Witte, W. G.; Whitlock, C. H.; Gurganus, E. A.

1979-01-01

Experimental measurements were made of upwelled spectral signatures of various concentrations of industrial waste products mixed with water in a large water tank. Radiance and reflectance spectra for a biosolid waste product (sludge) mixed with conditioned tap water and natural river water are reported. Results of these experiments indicate that reflectance increases with increasing concentration of the sludge at practically all wavelengths for concentration of total suspended solids up to 117 ppm in conditioned tap water and 171 ppm in natural river water. Significant variations in the spectra were observed and may be useful in defining spectral characteristics for this waste product. No significant spectral differences were apparent in the reflectance spectra of the two experiments, especially for wavelengths greater than 540 nm. Reflectance values, however, were generally greater in natural river water for wavelengths greater than 540 nm. Reflectance may be considered to increase linearly with concentration of total suspended solids from 5 to 171 ppm at all wavelengths without introducing errors larger than 10 percent.

Energy-environmental benefits and economic feasibility of anaerobic codigestion of Iberian pig slaughterhouse and tomato industry wastes in Extremadura (Spain).

PubMed

González-González, A; Cuadros, F; Ruiz-Celma, A; López-Rodríguez, F

2013-05-01

Anaerobic digestion of Iberian pig slaughterhouse and tomato industry wastes, as well as codigestion operations from such residues, are reported to achieve 54-80% reduction in Chemical Oxygen Demand and 6-19 N m(3)/m(3) substrate methane production. Furthermore, 0.79-0.88 m(3)water/m(3) substrate is seen to be recovered after the above mentioned operations, which might be used as irrigation water, and 0.12-0.21 m(3)agricultural amendment/m(3) substrate with 91-98% moisture content. The present paper also reports on the economic feasibility of both an anaerobic codigestion plant operating with 60% slaughterhouse wastes/40% tomato industry wastes (optimal ratio obtained in previous laboratory-scaled experiments), and an anaerobic digestion plant for Iberian pig slaughterhouse waste. Payback times are reported as 14.86 and 3.73 years, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Water and wastewater minimization plan in food industries.

PubMed

Ganjidoust, H; Ayati, B

2002-01-01

Iran is one of the countries located in a dry and semi-dry area. Many provinces like Tehran are facing problems in recent years because of less precipitation. For reduction in wastewater treatment cost and water consumption, many research works have been carried out. One of them concerns food industries group, which consumes a great amount of water in different units. For example, in beverage industries, washing of glass bottles seven times requires large amounts of water but use of plastic bottles can reduce water consumption. Another problem is leakage from pipelines, valves, etc. Their repair plays an important role in the wastage of water. The non-polluted wasted water can be used in washing halls, watering green yards, recycling to the process or reusing in cooling towers. In this paper, after a short review of waste minimization plans in food industries, problems concerning water consuming and wastewater producing units in three Iranian food industries have been investigated. At the end, some suggestions have been given for implementing the water and wastewater minimization plan in the companies.

Food-Processing Wastes.

PubMed

Frenkel, Val S; Cummings, Gregg A; Maillacheruvu, K Y; Tang, Walter Z

2015-10-01

Literature published in 2014 and early 2015 related to food processing wastes treatment for industrial applications are reviewed. This review is a subsection of the Treatment Systems section of the annual Water Environment Federation literature review and covers the following food processing industries and applications: general, meat and poultry, fruits and vegetables, dairy and beverage, and miscellaneous treatment of food wastes.

Food-Processing Wastes.

PubMed

Frenkel, Val S; Cummings, Gregg A; Maillacheruvu, K Y; Tang, Walter Z

2017-10-01

Literature published in 2016 and early 2017 related to food processing wastes treatment for industrial applications are reviewed. This review is a subsection of the Treatment Systems section of the annual Water Environment Federation literature review and covers the following food processing industries and applications: general, meat and poultry, fruits and vegetables, dairy and beverage, and miscellaneous treatment of food wastes.

Food-Processing Wastes.

PubMed

Frenkel, Val S; Cummings, Gregg A; Maillacheruvu, K Y; Tang, Walter Z

2016-10-01

Literature published in 2015 and early 2016 related to food processing wastes treatment for industrial applications are reviewed. This review is a subsection of the Treatment Systems section of the annual Water Environment Federation literature review and covers the following food processing industries and applications: general, meat and poultry, fruits and vegetables, dairy and beverage, and miscellaneous treatment of food wastes.

Waste water biological purification plants of dairy products industry and energy management

NASA Astrophysics Data System (ADS)

Stepanov, Sergey; Solkina, Olga; Stepanov, Alexander; Zhukova, Maria

2017-10-01

The paper presents results of engineering and economical comparison of waste water biological purification plants of dairy products industry. Three methods of purification are compared: traditional biological purification with the use of secondary clarifiers and afterpurification through granular-bed filters, biomembrane technology and physical-and-chemical treatment together with biomembrane technology for new construction conditions. The improvement of the biological purification technology using nitro-denitrification and membrane un-mixing of sludge mixture is a promising trend in this area. In these calculations, an energy management which is widely applied abroad was used. The descriptions of the three methods are illustrated with structural schemes. Costs of equipment and production areas are taken from manufacturers’ data. The research is aimed at an engineering and economical comparison of new constructions of waste water purification of dairy products industry. The experiment demonstrates advantages of biomembrane technology in waste water purification. This technology offers prospects of 122 million rubles cost saving during 25 years of operation when compared with of the technology of preparatory reagent flotation and of 13.7 million rubles cost saving compared to the option of traditional biological purification.

Contaminated earth and water: a legacy of the synthetic dyestuffs industry.

PubMed

Travis, Anthony S

2002-03-01

This paper demonstrates that the subject of the transport and fate of waste from the synthetic dye industry in far more than a footnote in history. It is actually a major chapter, encompassing both Europe and the United States. Indeed, in the 1990s there was as much interest in the history of the industry and its wastes among environmental litigators, particularly in the United States, as there was in the history of the dye industry among historians of chemistry. Review and analysis of various sources (ranging from expert reports, through early legislation, lobbying by and on behalf of the synthetic dyestuffs industry, methods of chemical detection and identification, and processes of waste handling and treatment) make it clear that much was known about the persistent and problematic nature of this waste. This included soil and groundwater contamination, as well as surface water pollution. There were considerable efforts to regulate manufacturers before 1890, but after that time the political and economic muscle of industry prevailed and prevented effective remedial action. Until the mid-twentieth century the industry effectively exerted its own destiny, self-regulatory and otherwise, even in the face of opposition.

43 CFR 8365.1-1 - Sanitation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... or petroleum products or dump refuse or waste other than wash water from any trailer or other vehicle... industrial refuse or waste brought as such from private or municipal property; (5) Pollute or contaminate water supplies or water used for human consumption; or (6) Use a refuse container or disposal facility...

Clean Water for the 1970's, A Status Report.

ERIC Educational Resources Information Center

Department of the Interior, Washington, DC. Federal Water Quality Administration.

This report describes the past activities and future plans of the Federal Water Quality Administration (FWQA). The first of the four sections in the report provides general discussion about these forms of water pollution: municipal wastes, industrial wastes, thermal pollution, oil and hazardous substances, mine drainage, sedimentation and erosion,…

Iron and aluminium oxides containing industrial wastes as adsorbents of heavy metals: Application possibilities and limitations.

PubMed

Jacukowicz-Sobala, Irena; Ociński, Daniel; Kociołek-Balawejder, Elżbieta

2015-07-01

Industrial wastes with a high iron or aluminium oxide content are produced in huge quantities as by-products of water treatment (water treatment residuals), bauxite processing (red mud) and hard and brown coal burning in power plants (fly ash). Although they vary in their composition, the wastes have one thing in common--a high content of amorphous iron and/or aluminium oxides with a large specific surface area, whereby this group of wastes shows very good adsorbability towards heavy metals, arsenates, selenates, etc. But their physical form makes their utilisation quite difficult, since it is not easy to separate the spent sorbent from the solution and high bed hydraulic resistances occur in dynamic regime processes. Nevertheless, because of the potential benefits of utilising the wastes in industrial effluent treatment, this issue attracts much attention today. This study describes in detail the waste generation processes, the chemical structure of the wastes, their physicochemical properties, and the mechanisms of fixing heavy metals and semimetals on the surface of iron and aluminium oxides. Typical compositions of wastes generated in selected industrial plants are given. A detailed survey of the literature on the adsorption applications of the wastes, including methods of their thermal and chemical activation, as well as regeneration of the spent sorbents, is presented. The existing and potential ways of modifying the physical form of the discussed group of wastes, making it possible to overcome the basic limitation on their practical use, are discussed. © The Author(s) 2015.

Water-quality and hydrogeologic data for three phosphate industry waste-disposal sites in central Florida, 1979-80

USGS Publications Warehouse

Miller, Ronald L.; Sutcliffe, Horace

1982-01-01

This report is a complilation of geologic, hydrologic, and water-quality data and information on test holes collected in the vicinity of gypsum stack complexes at two phosphate chemical plants and one phosphatic clayey waste disposal pond at a phosphate mine and beneficiation plant in central Florida. The data were collected from September 1979 to October 1980 at thee AMAX Phosphate, Inc., chemical plant, Piney Point; the USS AgriChemicals chemical plant, Bartow; and the International Minerals and Chemical Corporation Clear Springs mine, Bartow. Approximmmtely 5,400 field and laboratory water-quality determinations on water samples were collected from about 78 test holes and 31 surface-water, rainfall, and other sampling sites at phosphate industry beneficiation and chemical plant waste-disposal operations. Maps show locations of sampling sites. (USGS)

Pharmaceutical wastewater being composite mixture of environmental pollutants may be associated with mutagenicity and genotoxicity.

PubMed

Sharif, Ali; Ashraf, Muhammad; Anjum, Aftab Ahmed; Javeed, Aqeel; Altaf, Imran; Akhtar, Muhammad Furqan; Abbas, Mateen; Akhtar, Bushra; Saleem, Ammara

2016-02-01

Pharmaceutical industries are amongst the foremost contributor to industrial waste. Ecological well-being is endangered owing to its facile discharge. In the present study, heavy metals and organic contaminants in waste water were characterized using atomic absorption spectrophotometer and GC-MS, respectively. Mutagenicity and genotoxic potential of pharmaceutical waste water were investigated through bacterial reverse mutation assay and in vitro comet assay, respectively. Ames test and comet assay of first sample were carried out at concentrations of 100, 50, 25, 12.5, 6.25 % v/v effluent with distilled water. Chromium (Cr), lead (Pb), arsenic (As), and cadmium (Cd) were found in high concentrations as compared to WHO- and EPA-recommended maximum limits. Arsenic was found to be the most abundant metal and its maximum concentration was 0.8 mg.L(-1). GC-MS revealed the presence of lignocaine, digitoxin, trimethoprim, caffeine, and vitamin E in waste water. Dose-dependent decrease in mutagenic index was observed in both strains. Substantial increase in mutagenicity was observed for TA-100, when assay was done by incorporating an enzyme activation system, whereas a slight increase was detected for TA-102. In vitro comet assay of waste water exhibited decrease in damage index and percentage fragmentation with the increase in dilution of waste water. Tail length also decreased with an increase in the dilution factor of waste water. These findings suggest that pharmaceutical waste water being a mix of different heavy metals and organic contaminants may have a potent mutagenic and genotoxic effect on exposed living organisms.

Impulse powerful UV-radiation source pumped by the sublight ionization waves for the bacteriological disinfection of water

NASA Astrophysics Data System (ADS)

Filiouguine, Igor V.; Kostiouchenko, S. V.; Koudryavtsev, N. N.; Vasilyak, Leonid M.; Yakimenko, A. V.

1993-11-01

The bacteriological disinfective action of UV-radiation is well known. The pioneer work on UV-radiation used for bacteriological disinfection of waste water was made in 1910. Because of the high cost and low living time of the UV-radiation sources, the alternative technique for waste water purification by chlorine introducing was spread out. During the second stage of the UV purification development, beginning in approximately 1970, the interest for bacteriological cleaning of water, increased again. Two reasons were responsible for this event: first, the significant improvement of technology and design of UV-bacteriological purificators, and second, recognition of the serious danger of chlorine compounds introduced into water under purification because of the toxicity of these compounds. Further investigations gave excellent results in the creation and industrial applications of UV- bacteriological purificators. Now we can see a rapid development of industrial technology in UV-purification of drinking and waste waters.

2011 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Frederick

2012-02-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (LA-000160-01), for the wastewater reuse site at the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from November 1, 2010 through October 31, 2011. The report contains the following information: (1) Facility and system description; (2) Permit required effluent monitoring data and loading rates; (3) Groundwater monitoring data; (4) Status of special compliance conditions; and (5) Discussion of the facility's environmental impacts. During the 2011 reporting year, an estimated 6.99 million gallons of wastewater were discharged to themore » Industrial Waste Ditch and Pond which is well below the permit limit of 13 million gallons per year. Using the dissolved iron data, the concentrations of all permit-required analytes in the samples from the down gradient monitoring wells were below the Ground Water Quality Rule Primary and Secondary Constituent Standards.« less

2010 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site's Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

David B. Frederick

2011-02-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (#LA 000160 01), for the wastewater reuse site at the Idaho National Laboratory Site’s Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from May 1, 2010 through October 31, 2010. The report contains the following information: • Facility and system description • Permit required effluent monitoring data and loading rates • Groundwater monitoring data • Status of special compliance conditions • Discussion of the facility’s environmental impacts During the 2010 partial reporting year, an estimated 3.646 million gallons of wastewater were dischargedmore » to the Industrial Waste Ditch and Pond which is well below the permit limit of 13 million gallons per year. The concentrations of all permit-required analytes in the samples from the down gradient monitoring wells were below the Ground Water Quality Rule Primary and Secondary Constituent Standards.« less

Disposal and improvement of contaminated by waste extraction of copper mining in chile

NASA Astrophysics Data System (ADS)

Naranjo Lamilla, Pedro; Blanco Fernández, David; Díaz González, Marcos; Robles Castillo, Marcelo; Decinti Weiss, Alejandra; Tapia Alvarez, Carolina; Pardo Fabregat, Francisco; Vidal, Manuel Miguel Jordan; Bech, Jaume; Roca, Nuria

2016-04-01

This project originated from the need of a mining company, which mines and processes copper ore. High purity copper is produced with an annual production of 1,113,928 tons of concentrate to a law of 32%. This mining company has generated several illegal landfills and has been forced by the government to make a management center Industrial Solid Waste (ISW). The forecast volume of waste generated is 20,000 tons / year. Chemical analysis established that the studied soil has a high copper content, caused by nature or from the spread of contaminants from mining activities. Moreover, in some sectors, soil contamination by mercury, hydrocarbons and oils and fats were detected, likely associated with the accumulation of waste. The waters are also impacted by mining industrial tasks, specifically copper ores, molybdenum, manganese, sulfates and have an acidic pH. The ISW management center dispels the pollution of soil and water and concentrating all activities in a technically suitable place. In this center the necessary guidelines for the treatment and disposal of soil contamination caused by uncontrolled landfills are given, also generating a leachate collection system and a network of fluid monitoring physicochemical water quality and soil environment. Keywords: Industrial solid waste, soil contamination, Mining waste

Solid waste management practices in wet coffee processing industries of Gidabo watershed, Ethiopia.

PubMed

Ulsido, Mihret D; Li, Meng

2016-07-01

The financial and social contributions of coffee processing industries within most coffee export-based national economies like Ethiopia are generally high. The type and amount of waste produced and the waste management options adopted by these industries can have negative effects on the environment. This study investigated the solid waste management options adopted in wet coffee processing industries in the Gidabo watershed of Ethiopia. A field observation and assessment were made to identify whether the operational characteristics of the industries have any effect on the waste management options that were practiced. The investigation was conducted on 125 wet coffee processing industries about their solid waste handling techniques. Focus group discussion, structured questionnaires, key informant interview and transect walks are some of the tools employed during the investigation. Two major types of wastes, namely hull-bean-pulp blended solid waste and wastewater rich in dissolved and suspended solids were generated in the industries. Wet mills, on average, released 20.69% green coffee bean, 18.58% water and 60.74% pulp by weight. Even though these wastes are rich in organic matter and recyclables; the most favoured solid waste management options in the watershed were disposal (50.4%) and industrial or household composting (49.6%). Laxity and impulsive decision are the driving motives behind solid waste management in Gidabo watershed. Therefore, to reduce possible contamination of the environment, wastes generated during the processing of red coffee cherries, such as coffee wet mill solid wastes, should be handled properly and effectively through maximisation of their benefits with minimised losses. © The Author(s) 2016.

40 CFR 240.201-2 - Recommended procedures: Design.

Code of Federal Regulations, 2010 CFR

2010-07-01

... carcasses, automobile bodies, dewatered sludges from water treatment plants, and industrial process wastes. ... WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures... or excluded wastes inadvertently left at the facility should be considered in design. (b) Examples of...

Multi-objective model of waste transportation management for crude palm oil industry

NASA Astrophysics Data System (ADS)

Silalahi, Meslin; Mawengkang, Herman; Irsa Syahputri, Nenna

2018-02-01

The crude palm oil industry is an agro-industrial commodity. The global market of this industry has experienced rapid growth in recent years, such that it has a strategic value to be developed for Indonesian economy. Despite these economic benefits there are a number of environmental problems at the factories, such as high water consumption, the generation of a large amount of wastewater with a high organic content, and the generation of a large quantity of solid wastes and air pollution. In terms of waste transportation, we propose a multiobjective programming model for managing business environmental risk in a crude palm oil manufacture which gives the best possible configuration of waste management facilities and allocates wastes to these facilities. Then we develop an interactive approach for tackling logistics and environmental risk production planning problem for the crude palm oil industry.

The physicochemical characteristics and anaerobic degradability of desiccated coconut industry waste water.

PubMed

Chanakya, H N; Khuntia, Himanshu Kumar; Mukherjee, Niranjan; Aniruddha, R; Mudakavi, J R; Thimmaraju, Preeti

2015-12-01

Desiccated coconut industries (DCI) create various intermediates from fresh coconut kernel for cosmetic, pharmaceutical and food industries. The mechanized and non-mechanized DCI process between 10,000 and 100,000 nuts/day to discharge 6-150 m(3) of malodorous waste water leading to a discharge of 264-6642 kg chemical oxygen demand (COD) daily. In these units, three main types of waste water streams are coconut kernel water, kernel wash water and virgin oil waste water. The effluent streams contain lipids (1-55 g/l), suspended solids (6-80 g/l) and volatile fatty acids (VFA) at concentrations that are inhibitory to anaerobic bacteria. Coconut water contributes to 20-50% of the total volume and 50-60% of the total organic loads and causes higher inhibition of anaerobic bacteria with an initial lag phase of 30 days. The lagooning method of treatment widely adopted failed to appreciably treat the waste water and often led to the accumulation of volatile fatty acids (propionic acid) along with long-chain unsaturated free fatty acids. Biogas generation during biological methane potential (BMP) assay required a 15-day adaptation time, and gas production occurred at low concentrations of coconut water while the other two streams did not appear to be inhibitory. The anaerobic bacteria can mineralize coconut lipids at concentrations of 175 mg/l; however; they are severely inhibited at a lipid level of ≥350 mg/g bacterial inoculum. The modified Gompertz model showed a good fit with the BMP data with a simple sigmoid pattern. However, it failed to fit experimental BMP data either possessing a longer lag phase and/or diauxic biogas production suggesting inhibition of anaerobic bacteria.

Locational Determinants of Emissions from Pollution-Intensive Firms in Urban Areas

PubMed Central

Zhou, Min; Tan, Shukui; Guo, Mingjing; Zhang, Lu

2015-01-01

Industrial pollution has remained as one of the most daunting challenges for many regions around the world. Characterizing the determinants of industrial pollution should provide important management implications. Unfortunately, due to the absence of high-quality data, rather few studies have systematically examined the locational determinants using a geographical approach. This paper aimed to fill the gap by accessing the pollution source census dataset, which recorded the quantity of discharged wastes (waste water and solid waste) from 717 pollution-intensive firms within Huzhou City, China. Spatial exploratory analysis was applied to analyze the spatial dependency and local clusters of waste emissions. Results demonstrated that waste emissions presented significantly positive autocorrelation in space. The high-high hotspots generally concentrated towards the city boundary, while the low-low clusters approached the Taihu Lake. Their locational determinants were identified by spatial regression. In particular, firms near the city boundary and county road were prone to discharge more wastes. Lower waste emissions were more likely to be observed from firms with high proximity to freight transfer stations or the Taihu Lake. Dense populous districts saw more likelihood of solid waste emissions. Firms in the neighborhood of rivers exhibited higher waste water emissions. Besides, the control variables (firm size, ownership, operation time and industrial type) also exerted significant influence. The present methodology can be applicable to other areas, and further inform the industrial pollution control practices. Our study advanced the knowledge of determinants of emissions from pollution-intensive firms in urban areas. PMID:25927438

40 CFR 35.925-15 - Treatment of industrial wastes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Treatment of industrial wastes. 35.925-15 Section 35.925-15 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works-Clean Water Act...

Recycled water reuse permit renewal application for the materials and fuels complex industrial waste ditch and industrial waste pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Name, No

This renewal application for the Industrial Wastewater Reuse Permit (IWRP) WRU-I-0160-01 at Idaho National Laboratory (INL), Materials and Fuels Complex (MFC) Industrial Waste Ditch (IWD) and Industrial Waste Pond (IWP) is being submitted to the State of Idaho, Department of Environmental Quality (DEQ). This application has been prepared in compliance with the requirements in IDAPA 58.01.17, Recycled Water Rules. Information in this application is consistent with the IDAPA 58.01.17 rules, pre-application meeting, and the Guidance for Reclamation and Reuse of Municipal and Industrial Wastewater (September 2007). This application is being submitted using much of the same information contained in themore » initial permit application, submitted in 2007, and modification, in 2012. There have been no significant changes to the information and operations covered in the existing IWRP. Summary of the monitoring results and operation activity that has occurred since the issuance of the WRP has been included. MFC has operated the IWP and IWD as regulated wastewater land treatment facilities in compliance with the IDAPA 58.01.17 regulations and the IWRP. Industrial wastewater, consisting primarily of continuous discharges of nonhazardous, nonradioactive, routinely discharged noncontact cooling water and steam condensate, periodic discharges of industrial wastewater from the MFC facility process holdup tanks, and precipitation runoff, are discharged to the IWP and IWD system from various MFC facilities. Wastewater goes to the IWP and IWD with a permitted annual flow of up to 17 million gallons/year. All requirements of the IWRP are being met. The Operations and Maintenance Manual for the Industrial Wastewater System will be updated to include any new requirements.« less

Solidification as low cost technology prior to land filling of industrial hazardous waste sludge.

PubMed

El-Sebaie, O; Ahmed, M; Ramadan, M

2000-01-01

The aim of this study is to stabilize and solidify two different treated industrial hazardous waste sludges, which were selected from factories situated close to Alexandria. They were selected to ensure their safe transportation and landfill disposal by reducing their potential leaching of hazardous elements, which represent significant threat to the environment, especially the quality of underground water. The selected waste sludges have been characterized. Ordinary Portland Cement (OPC), Cement Kiln Dust (CKD) from Alexandria Portland Cement Company, and Calcium Sulphate as a by-product from the dye industry were used as potential solidification additives to treat the selected treated waste sludges from tanning and dyes industry. Waste sludges as well as the solidified wastes have been leach-tested, using the General Acid Neutralization Capacity (GANC) procedure. Concentration of concerning metals in the leachates was determined to assess changes in the mobility of major contaminants. The treated tannery waste sludge has an acid neutralization capacity much higher than that of the treated dyes waste sludge. Experiment results demonstrated the industrial waste sludge solidification mix designs, and presented the reduction of contaminant leaching from two types of waste sludges. The main advantages of solidification are that it is simple and low cost processing which includes readily available low cost solidification additives that will convert industrial hazardous waste sludges into inert materials.

Utilization of industrial dairy waste as microalgae cultivation medium : a potential study for sustainable energy resources

NASA Astrophysics Data System (ADS)

Nurmayani, S.; Sugiarti, Y.; Putra, R. H.

2016-04-01

Microalgae is one of biodiesel resources and call as third generation biofuel. Biodiesel is one alternative energy that being developed. So study about resource of biodiesel need a development, for the example is development the basic material such as microalgae. In this paper we explain the potential use of dairy waste from industry as a cultivation medium of microalgae for biodiesel production. Dairy waste from dairy industry contains 34.98% protein, 4.42% lactose, 9.77% fiber, 11.04% fat, 2.33% calcium, 1.05% phosfor, and 0.4 % magnesium, meaning that the dairy waste from dairy industry has a relatively high nutrient content and complete from a source of carbon, nitrogen and phosphorus as macro nutrients. The method in this paper is literature review to resulting a new conclusion about the potency of waste water from dairy industry as microalgae cultivation medium. Based on the study, the dairy waste from dairy industry has potency to be used as cultivation medium of Botryococcus braunii in the production of biodiesel, replacing the conventional cultivation medium.

Sorption of PFOA and PFOS to Ground Water Sediment

EPA Science Inventory

During its years of operation, the Washington County Sanitary Landfill near St. Paul, Minnesota accepted both municipal and industrial solid waste. Several years of ground water monitoring performed by the MPCA indicates that, some of the waste disposed of at this landfill contai...

CONTROL OF CHELATOR-BASED UPSETS IN SURFACE FINISHING SHOP WASTE WATER TREATMENT SYSTEMS

EPA Science Inventory

Actual surface finishing shop examples are used to illustrate the use of process chemistry understanding and analyses to identify immediate, interim and permanent response options for industrial waste water treatment plant (IWTP) upset problems caused by chelating agents. There i...

Production of nano bacterial cellulose from waste water of candied jujube-processing industry using Acetobacter xylinum.

PubMed

Li, Zheng; Wang, Lifen; Hua, Jiachuan; Jia, Shiru; Zhang, Jianfei; Liu, Hao

2015-04-20

The work is aimed to investigate the suitability of waste water of candied jujube-processing industry for the production of bacterial cellulose (BC) by Gluconacetobacter xylinum CGMCC No.2955 and to study the structure properties of bacterial cellulose membranes. After acid pretreatment, the glucose of hydrolysate was higher than that of waste water of candied jujube. The volumetric yield of bacterial cellulose in hydrolysate was 2.25 g/L, which was 1.5-folds of that in waste water of candied jujube. The structures indicated that the fiber size distribution was 3-14 nm in those media with an average diameter being around 5.9 nm. The crystallinity index of BC from pretreatment medium was lower than that of without pretreatment medium and BCs from various media had similar chemical binding. Ammonium citrate was a key factor for improving production yield and the crystallinity index of BC. Copyright © 2014 Elsevier Ltd. All rights reserved.

Superfund Record of Decision (EPA Region 3): Harvey-Knott Drum site, New Castle County, Delaware, September 1985. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Harvey-Knott Drum Site is located in New Castle County, Delaware, approximately one-half mile east of the Maryland-Delaware border. The Harvey and Knotts Trucking, Inc., operated an open dump and burning ground on the site between 1963 and 1969. The facility accepted sanitary, municipal, and industrial wastes believed to be sludges, paint pigments, and solvents. Wastes were emptied onto the ground, into excavated trenches, or left in drums (some of which were buried). Some of these wastes were either burned as a means of reducing waste volume, or allowed to seep into the soil. Contamination of soil, surface water, andmore » ground water has occurred as a result of disposal of these industrial wastes. The selected remedial action for this site is included.« less

[Cultivation of a permanent fish cell line in serum-free media special experiences with a cytotoxicity test for waste water samples

PubMed

Kohlpoth, Martin; Rusche, Brigitte

1997-01-01

The use of fetal calf serum (FCS) as standard medium additive for the cell cultivation must be regarded critically from the point of view of animal welfare as well as for scientific reasons and makes it necessary to look for alternatives. In the last years an in vitro cytotoxicity assay for the testing of industrial waste waters with the permanent fish cell line RTG-2 was established and pre-validated as an alternative to the fish test with the golden orfe. The application of FCS is also a special problem with regard to the testing of waste waters in a cytotoxicity test so that FCS-alternatives were tested. The RTG-2 cells were successfully adapted to the two solvents Basal Medium Supplement (BMS) and Ultroser-G (U-G) that are used to replace serum. The characterisation of these adapted cell lines showed no significant differences in growth rate, adhesion rate, viability and sensitivity to chemicals in comparison to the original RTG-2 cells. On the determination of the cytotoxicity of industrial waste waters the RTG-2 cells adapted to the BMS medium indicated a clearly higher toxicity of the waste water samples than the original RTG-2 cells. This result confirms the thesis that serum components react with waste water elements and thus change the bio-availability of toxic compounds.

Water Pollution Abstracts. Volume 43, Number 4, Abstracts 645-849.

DTIC Science & Technology

WATER POLLUTION, *ABSTRACTS, PURIFICATION, WASTES(INDUSTRIAL), CONTROL, SEWAGE, WATER SUPPLIES, PUBLIC HEALTH, PETROLEUM PRODUCTS, DEGRADATION, DAMS...ESTUARIES, PLANKTON, PHOTOSYNTHESIS, VIRUSES, SEA WATER , MICROBIOLOGY, UNITED KINGDOM.

The Empirical Relationship between Mining Industry Development and Environmental Pollution in China.

PubMed

Li, Gerui; Lei, Yalin; Ge, Jianping; Wu, Sanmang

2017-03-02

This study uses a vector autoregression (VAR) model to analyze changes in pollutants among different mining industries and related policy in China from 2001 to 2014. The results show that: (1) because the pertinence of standards for mining waste water and waste gas emissions are not strong and because the maximum permissible discharge pollutant concentrations in these standards are too high, ammonia nitrogen and industrial sulfur dioxide discharges increased in most mining industries; (2) chemical oxygen demand was taken as an indicator of sewage treatment in environmental protection plans; hence, the chemical oxygen demand discharge decreased in all mining industries; (3) tax reduction policies, which are only implemented in coal mining and washing and extraction of petroleum and natural gas, decreased the industrial solid waste discharge in these two mining industries.

National economic models of industrial water use and waste treatment. [technology transfer

NASA Technical Reports Server (NTRS)

Thompson, R. G.; Calloway, J. A.

1974-01-01

The effects of air emission and solid waste restrictions on production costs and resource use by industry is investigated. A linear program is developed to analyze how resource use, production cost, and waste discharges in different types of production may be affected by resource limiting policies of the government. The method is applied to modeling ethylene and ammonia plants at the design stage. Results show that the effects of increasingly restrictive wastewater effluent standards on increased energy use were small in both plants. Plant models were developed for other industries and the program estimated effects of wastewater discharge policies on production costs of industry.

Water Reuse and Wastewater Recycling at U.S. Army Installations: Policy Implications

DTIC Science & Technology

2011-06-01

Definition Blackwater Water captured from toilets and urinals along with kitchen waste. Direct potable reuse The introduction of highly treated reclaimed...reused. It does not include water from kitchen sinks or dishwashers. Indirect potable reuse The planned incorporation of reclaimed water into a raw...industrial cooling. * Some organizations do accept a definition of “graywater” that does include kitchen and dishwasher waste- water along with wastewater

The Experience of Implementation of Innovative Technology of Quarry Waste Water Purifying in Kuzbass Open Pit

NASA Astrophysics Data System (ADS)

Lesin, Yu V.; Hellmer, M. C.

2016-08-01

Among all industries in Kuzbass (Western Siberia, Russia) the coal industry provides the most environmental threat. However, the construction of new and maintenance of existing open pit mines do not often correspond to the tasks of improving the environmental safety of surface mining. So the article describes the use of innovative quarry waste water purifying technology implemented in Kuzbass open pit mine «Shestaki». This technology is based on using artificial filter arrays made of overburden rock.

Environmental impact statement for Manned Spacecraft Center and White Sands Test Facility

NASA Technical Reports Server (NTRS)

1971-01-01

This environment has not only attracted people and increased payrolls, but has also created a broader base for the local economy. The activity of the center was a catalyst to private enterprise and has led to sizeable residential and commercial developments. Adequate treatment of domestic and industrial waste water was maintained. A feasibility study is now being conducted to establish a plan for a coordinated, centerwide plan for advanced treatment of domestic and industrial waste water.

Using phytoremediation technologies to upgrade waste water treatment in Europe.

PubMed

Schröder, Peter; Navarro-Aviñó, Juan; Azaizeh, Hassan; Goldhirsh, Avi Golan; DiGregorio, Simona; Komives, Tamas; Langergraber, Günter; Lenz, Anton; Maestri, Elena; Memon, Abdul R; Ranalli, Alfonso; Sebastiani, Luca; Smrcek, Stanislav; Vanek, Tomas; Vuilleumier, Stephane; Wissing, Frieder

2007-11-01

One of the burning problems of our industrial society is the high consumption of water and the high demand for clean drinking water. Numerous approaches have been taken to reduce water consumption, but in the long run it seems only possible to recycle waste water into high quality water. It seems timely to discuss alternative water remediation technologies that are fit for industrial as well as less developed countries to ensure a high quality of drinking water throughout Europe. The present paper discusses a range of phytoremediation technologies to be applied in a modular approach to integrate and improve the performance of existing wastewater treatment, especially towards the emerging micro pollutants, i.e. organic chemicals and pharmaceuticals. This topic is of global relevance for the EU. Existing technologies for waste water treatment do not sufficiently address increasing pollution situation, especially with the growing use of organic pollutants in the private household and health sector. Although some crude chemical approaches exist, such as advanced oxidation steps, most waste water treatment plants will not be able to adopt them. The same is true for membrane technologies. Incredible progress has been made during recent years, thus providing us with membranes of longevity and stability and, at the same time, high filtration capacity. However, these systems are expensive and delicate in operation, so that the majority of communities will not be able to afford them. Combinations of different phytoremediation technologies seem to be most promising to solve this burning problem. To quantify the occurrence and the distribution of micropollutants, to evaluate their effects, and to prevent them from passing through wastewater collection and treatment systems into rivers, lakes and ground water bodies represents an urgent task for applied environmental sciences in the coming years. Public acceptance of green technologies is generally higher than that of industrial processes. The EU should stimulate research to upgrade existing waste water treatment by implementing phytoremediation modules and demonstrating their reliability to the public.

Look into Waste.

ERIC Educational Resources Information Center

Undy, Harry, Ed.

This booklet is designed to help British teachers introduce concepts of waste to secondary school students. The document focuses on various types of waste and pollution--air, land, water, and industrial--and suggests activities to help students understand and combat waste of natural and human resources. It is presented in 11 chapters. Six chapters…

2012 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site’s Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mike Lewis

2013-02-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (WRU-I-0160-01, formerly LA 000160 01), for the wastewater reuse site at the Idaho National Laboratory Site’s Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from November 1, 2011 through October 31, 2012. The report contains the following information: • Facility and system description • Permit required effluent monitoring data and loading rates • Groundwater monitoring data • Status of special compliance conditions • Discussion of the facility’s environmental impacts During the 2012 reporting year, an estimated 11.84 million gallons of wastewater weremore » discharged to the Industrial Waste Ditch and Pond which is well below the permit limit of 17 million gallons per year. The concentrations of all permit-required analytes in the samples from the down gradient monitoring wells were below the Ground Water Quality Rule Primary and Secondary Constituent Standards.« less

Influence of the processed sunflower oil on the cement properties

NASA Astrophysics Data System (ADS)

Fleysher, A. U.; Tokarchuk, V. V.; Sviderskiy, V. A.

2015-01-01

Used oils (vegetable oil, animal oil, engine oil, etc.), which are essentially industrial wastes, have found application as secondary raw materials in some braches of industry. In particular, the only well-known and commonly-used way of utilizing wastes of vegetable oils is to apply them as raw materials in the production of biodiesel. The goal of the present study is to develop a conceptually new way of vegetable oil wastes utilization in the building industry. The test admixture D-148 was obtained from the processing of wastes of sunflower oil and it mainly consists of fatty acid diethanolamide. The test admixture was added to the cement system for the purpose of studying its influence on water demand, flowability, setting times, compressive strength and moisture adsorption. The test admixture D-148 at the optimal content 0. 2 weight % causes 10% decrease in water demand, 1.7 time increase in flowability (namely spread diameter), 23% increase in grade strength and 34% decrease in moisture adsorption. The results of the present investigation make it possible to consider the final product of the waste sunflower oil processing as multifunctional plasticizing-waterproofing admixture.

Oil Based Drilling Fluid Waste: An Overview on Environmentally Persistent Pollutants

NASA Astrophysics Data System (ADS)

Siddique, Shohel; Kwoffie, Lorraine; Addae-Afoakwa, Kofi; Yates, Kyari; Njuguna, James

2017-05-01

Operational discharges of spent drilling fluid, produced water, and accumulated drill cuttings from oil and gas industry are a continuous point source of environmental pollution. To meet the strict environmental standard for waste disposal, oil and gas industry is facing a numerous challenges in technological development to ensure a clean and safe environment. Oil and gas industry generates a large amount of spent drilling fluid, produced water, and drill cuttings, which are very different in every drilling operation in terms of composition and characterisation. This review article highlights the knowledge gap in identifying the different sources of waste streams in combined drilling waste. This paper also emphasises how different chemicals turn into environmentally significant pollutants after serving great performance in oil and gas drilling operations. For instance, oil based drilling fluid performs excellent in deeper drilling and drilling in the harsh geological conditions, but ended with (produces) a significant amount of persistent toxic pollutants in the environment. This review paper provides an overview on the basic concepts of drilling fluids and their functions, sources and characterisation of drilling wastes, and highlights some environmentally significant elements including different minerals present in drilling waste stream.

Study on shrimp waste water and vermicompost as a nutrient source for bell peppers

USDA-ARS?s Scientific Manuscript database

The aquaculture industry generates significant nutrient-rich wastewater that is released into streams and rivers causing environmental concern. The objective of this controlled environment study was to evaluate the effect of waste shrimp water (SW), vermicompost (VC), at rates of 10%, 20%, 40%, and ...

Food waste disposal units in UK households: the need for policy intervention.

PubMed

Iacovidou, Eleni; Ohandja, Dieudonne-Guy; Voulvoulis, Nikolaos

2012-04-15

The EU Landfill Directive requires Member States to reduce the amount of biodegradable waste disposed of to landfill. This has been a key driver for the establishment of new waste management options, particularly in the UK, which in the past relied heavily on landfill for the disposal of municipal solid waste (MSW). MSW in the UK is managed by Local Authorities, some of which in a less conventional way have been encouraging the installation and use of household food waste disposal units (FWDs) as an option to divert food waste from landfill. This study aimed to evaluate the additional burden to water industry operations in the UK associated with this option, compared with the benefits and related savings from the subsequent reductions in MSW collection and disposal. A simple economic analysis was undertaken for different FWD uptake scenarios, using the Anglian Region as a case study. Results demonstrated that the significant savings from waste collection arising from a large-scale uptake of FWDs would outweigh the costs associated with the impacts to the water industry. However, in the case of a low uptake, such savings would not be enough to cover the increased costs associated with the wastewater provision. As a result, this study highlights the need for policy intervention in terms of regulating the use of FWDs, either promoting them as an alternative to landfill to increase savings from waste management, or banning them as a threat to wastewater operations to reduce potential costs to the water industry. Copyright © 2012 Elsevier B.V. All rights reserved.

Method for processing aqueous wastes

DOEpatents

Pickett, John B.; Martin, Hollis L.; Langton, Christine A.; Harley, Willie W.

1993-01-01

A method for treating waste water such as that from an industrial processing facility comprising the separation of the waste water into a dilute waste stream and a concentrated waste stream. The concentrated waste stream is treated chemically to enhance precipitation and then allowed to separate into a sludge and a supernate. The supernate is skimmed or filtered from the sludge and blended with the dilute waste stream to form a second dilute waste stream. The sludge remaining is mixed with cementitious material, rinsed to dissolve soluble components, then pressed to remove excess water and dissolved solids before being allowed to cure. The dilute waste stream is also chemically treated to decompose carbonate complexes and metal ions and then mixed with cationic polymer to cause the precipitated solids to flocculate. Filtration of the flocculant removes sufficient solids to allow the waste water to be discharged to the surface of a stream. The filtered material is added to the sludge of the concentrated waste stream. The method is also applicable to the treatment and removal of soluble uranium from aqueous streams, such that the treated stream may be used as a potable water supply.

Production of sorbent from paper industry solid waste for oil spill cleanup.

PubMed

Demirel Bayık, G; Altın, A

2017-12-15

The aim of the study is to select a cellulosic waste material from paper industry solid wastes and process it for sorbent production. Four different solid wastes were collected from a local paper production facility and rejects were selected due to its sorption capacity and processability. Oil sorption experiments were conducted according to the ASTM F 726-12 method. Effect of sorbent dosage, contact and dripping time, recovery of the oil, reusability of the sorbent and sorption from the water surface were also determined. Maximum oil sorption capacity was determined as 9.67, 12.92 and 12.84g/g for diesel oil, 0W30 and 10W30 motor oils respectively for the static test and 8.27, 10.45 and 11.69g/g for the dynamic test. An efficient and low-cost sorbent was produced from paper industry rejects that can be used on land and on water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Defusing the Toxics Threat: Controlling Pesticides and Industrial Waste. Worldwatch Paper 79.

ERIC Educational Resources Information Center

Postel, Sandra

The use of pesticides in agriculture and the discarding of industrial chemical waste into the air, soil, and water constitute two major pathways of human exposure to toxic substances. It is argued that these practices release hundreds of millions of tons of potentially hazardous substances into the environment each year. Speculation continues into…

40 CFR 60.2145 - How do I demonstrate continuous compliance with the emission limitations and the operating limits?

Code of Federal Regulations, 2014 CFR

2014-07-01

... NEW STATIONARY SOURCES Standards of Performance for Commercial and Industrial Solid Waste Incineration... own or operate an existing commercial or industrial combustion unit that combusted a fuel or non-waste... external corrosion. (3) Use a pressure sensor with a minimum tolerance of 1.27 centimeters of water or a...

Recycling ferrous sulfate via super-oxidant synthesis

NASA Astrophysics Data System (ADS)

Kanari, N.; Evrard, O.; Neveux, N.; Ninane, L.

2001-11-01

Hydrated ferrous sulfate, a by-product of the titanium-dioxide and steel-surface-treatment industries, is usually disposed of as waste at a significant extra cost for these industries. Due to tight environmental regulations in the European countries, waste disposal of ferrous sulfate will not be an acceptable solution in the near future. Consequently, the waste will have to be treated. Recently, ferrous sulfate was successfully used to synthesize a novel superoxidant material (potassium ferrate) containing iron in hexavalent state (FeVI). With ferrates synthesis, innovative applications are possible in different industrial sectors, such as treatment of water and wastewater and effluent decontamination.

Quality and management of wastewater in sugar industry

NASA Astrophysics Data System (ADS)

Poddar, Pradeep Kumar; Sahu, Omprakash

2017-03-01

Wastewater from sugar industries is one that has complex characteristics and is considered a challenge for environmental engineers in terms of treatment as well as utilization. Before treatment and recycling, determination of physicochemical parameter is an important mechanism. Many different types of techniques are introduced and modified for the purpose, but depend upon the water quality parameters. The main aim of this study is to determine the physicochemical characteristics of sugar industry waste water by the standard method and minimize the fresh water consumption in sugar industry by water pinch methodology.

The Empirical Relationship between Mining Industry Development and Environmental Pollution in China

PubMed Central

Li, Gerui; Lei, Yalin; Ge, Jianping; Wu, Sanmang

2017-01-01

This study uses a vector autoregression (VAR) model to analyze changes in pollutants among different mining industries and related policy in China from 2001 to 2014. The results show that: (1) because the pertinence of standards for mining waste water and waste gas emissions are not strong and because the maximum permissible discharge pollutant concentrations in these standards are too high, ammonia nitrogen and industrial sulfur dioxide discharges increased in most mining industries; (2) chemical oxygen demand was taken as an indicator of sewage treatment in environmental protection plans; hence, the chemical oxygen demand discharge decreased in all mining industries; (3) tax reduction policies, which are only implemented in coal mining and washing and extraction of petroleum and natural gas, decreased the industrial solid waste discharge in these two mining industries. PMID:28257126

Bioremediation for coal-fired power stations using macroalgae.

PubMed

Roberts, David A; Paul, Nicholas A; Bird, Michael I; de Nys, Rocky

2015-04-15

Macroalgae are a productive resource that can be cultured in metal-contaminated waste water for bioremediation but there have been no demonstrations of this biotechnology integrated with industry. Coal-fired power production is a water-limited industry that requires novel approaches to waste water treatment and recycling. In this study, a freshwater macroalga (genus Oedogonium) was cultivated in contaminated ash water amended with flue gas (containing 20% CO₂) at an Australian coal-fired power station. The continuous process of macroalgal growth and intracellular metal sequestration reduced the concentrations of all metals in the treated ash water. Predictive modelling shows that the power station could feasibly achieve zero discharge of most regulated metals (Al, As, Cd, Cr, Cu, Ni, and Zn) in waste water by using the ash water dam for bioremediation with algal cultivation ponds rather than storage of ash water. Slow pyrolysis of the cultivated algae immobilised the accumulated metals in a recalcitrant C-rich biochar. While the algal biochar had higher total metal concentrations than the algae feedstock, the biochar had very low concentrations of leachable metals and therefore has potential for use as an ameliorant for low-fertility soils. This study demonstrates a bioremediation technology at a large scale for a water-limited industry that could be implemented at new or existing power stations, or during the decommissioning of older power stations. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization of industrial wastes as raw materials for Emulsified Modified Bitumen (EMB) formulation

NASA Astrophysics Data System (ADS)

Najib Razali, Mohd; Isa, Syarifah Nur Ezatie Mohd; Salehan, Noor Adilah Md; Musa, Musfafikri; Aziz, Mohd Aizudin Abd; Nour, Abdurahman Hamid; Yunus, Rosli Mohd

2018-04-01

This study was conducted to characterize industrial wastes for formulation of emulsified modified bitumen (EMB) in relation to their physical characteristic and elemental composition. This analysis will give information either raw materials from industrial wastes can be used for EMB formulation. Bitumen is produced from crude oil that is extracted from the ground which categorizes the crude oil as one of the non-renewable form of product. A vast environmental problem issues arises in Malaysia cause by the excessive manufacturing activity that lead to a miss-management of industrial waste has leads to the used of industrial waste in the EMB formulation. Industrial waste such as polystyrene, polyethylene and used automotive oil can be used as alternative to formulate bitumen. Then a suitable emulsifier needs to be added to produce the final product which is EMB. The emulsifier will yield a charge depends on its properties to bind the oily bitumen with water. Physical characteristic studies were performed by thermogravimetric Analysis (TGA), differential scanning calorimetry (DSC), flash point test, density rest and moisture content test. Fourier Transform Infrared Spectroscopy (FTIR) analysis was measured to determine the material’s molecular composition and structure.

Utilization of inorganic industrial wastes in producing construction ceramics. Review of Russian experience for the years 2000-2015.

PubMed

Boltakova, N V; Faseeva, G R; Kabirov, R R; Nafikov, R M; Zakharov, Yu A

2017-02-01

This paper analyzes the significant scientific publications worldwide for the last 15years concerning construction ceramics (predominantly brick) made with various inorganic industrial wastes added to the ceramic raw material for the improvement of properties and for eco-friendly disposal. The information gap resulting from the lack of mentions of the Russian publications on this subject in English-language reviews is filled. The paper includes brief summaries of 34 dissertations and 29 patents issued in Russia since 2000. The waste additives described in these summaries are grouped by origin type (mining industry waste, ore enrichment waste, metallurgical waste, sludge, ashes, cullet, large-capacity building wastes and waste from various chemical production processes) with the ceramic mixture compositions, molding and firing conditions, final strength, water absorption and other parameters of the final ceramic samples reported. Russian scientists have expanded the nomenclature of each group of wastes significantly upon addition to the list described in English-language reviews for 2000-2015. References to the recent Russian developments in the field of ecological management in ceramic industry are provided. Copyright © 2016 Elsevier Ltd. All rights reserved.

Separation of motor oils, oily wastes and hydrocarbons from contaminated water by sorption on chrome shavings.

PubMed

Gammoun, A; Tahiri, S; Albizane, A; Azzi, M; Moros, J; Garrigues, S; de la Guardia, M

2007-06-25

In this paper, the ability of chrome shavings to remove motor oils, oily wastes and hydrocarbons from water has been studied. To determine amount of hydrocarbons sorbed on tanned wastes, a FT-NIR methodology was used and a multivariate calibration based on partial least squares (PLS) was employed for data treatment. The light density, porous tanned waste granules float on the surface of water and remove hydrocarbons and oil films. Wastes fibers from tannery industry have high sorption capacity. These tanned solid wastes are capable of absorbing many times their weight in oil or hydrocarbons (6.5-7.6g of oil and 6.3g of hydrocarbons per gram of chrome shavings). The removal efficiency of the pollutants from water is complete. The sorption of pollutants is a quasi-instantaneous process.

Remediation of lead from lead electroplating industrial effluent using sago waste.

PubMed

Jeyanthi, G P; Shanthi, G

2007-01-01

Heavy metals are known toxicants, which inflict acute disorders to the living beings. Electroplating industries pose great threat to the environment through heavy load of metals in the wastewater discharged on land and water sources. In the present study, sago processing waste, which is both a waste and a pollutant, was used to adsorb lead ions from lead electroplating industrial effluent. Two types of sago wastes, namely, coarse sago waste and fine sago waste were used to study their adsorption capacity with the batch adsorption and Freundlich adsorption isotherm. The parameters that were considered for batch adsorption were pH (4, 5 and 6), time of contact (1, 2 and 3 hrs), temperature (30, 37 and 45 degrees C) and dosage of the adsorbent (2,4 and 6 g/L). The optimal condition for the effective removal of lead was found to be pH 5, time of contact 3 hrs, temperature 30 degrees C and dosage 4 g/L with coarse sago waste than fine sago waste.

Environmental justice implications of industrial hazardous waste generation in India: a national scale analysis

NASA Astrophysics Data System (ADS)

Basu, Pratyusha; Chakraborty, Jayajit

2016-12-01

While rising air and water pollution have become issues of widespread public concern in India, the relationship between spatial distribution of environmental pollution and social disadvantage has received less attention. This lack of attention becomes particularly relevant in the context of industrial pollution, as India continues to pursue industrial development policies without sufficient regard to its adverse social impacts. This letter examines industrial pollution in India from an environmental justice (EJ) perspective by presenting a national scale study of social inequities in the distribution of industrial hazardous waste generation. Our analysis connects district-level data from the 2009 National Inventory of Hazardous Waste Generating Industries with variables representing urbanization, social disadvantage, and socioeconomic status from the 2011 Census of India. Our results indicate that more urbanized and densely populated districts with a higher proportion of socially and economically disadvantaged residents are significantly more likely to generate hazardous waste. The quantity of hazardous waste generated is significantly higher in more urbanized but sparsely populated districts with a higher proportion of economically disadvantaged households, after accounting for other relevant explanatory factors such as literacy and social disadvantage. These findings underscore the growing need to incorporate EJ considerations in future industrial development and waste management in India.

Incinerator technology overview

NASA Astrophysics Data System (ADS)

Santoleri, Joseph J.

1991-04-01

In the 1960's, much effort was expended on cleaning up the air and water. Air Quality and Water Quality Acts were written and inpleinented in many states and coninunities. New products such as unleaded gasoline and water base paints were developed to aid in minimizing pollution. Conversion from oil fired combustion systems to natural gas fired for comfort and industrial heating was the normal practice. In 1970, the Clean Air Act was passed. There was concern on how to safely dispose of hazardous wastes. Indiscriminate dumping of chemical process wastes had been the practice since the birth of the chemical industry in the USA. Land dumping, inadequate landfills, and river-ocean dumping were the most economical ways to dispose of chemical wastes. Processes that would have reduced or eliminated wastes were disregarded as being too costly. Many of the major chemical companies who regarded a safe environment as their responsibility installed waste treatment and disposal facilities on their plant sites. Many of these plants elected to use incinerators as the treatment process. This was not always the most economical method, but in many cases it was the only method of disposal that provided a safe and sure method of maximum destruction. Environmental concern over contamination from uncontrolled land disposal sites, and the emergence of tougher regulations for land disposal provide incentives for industry to employ a wide variety of traditional and advanced technologies for managing hazardous wastes. Incineration systems utilizing proper design, operation, and maintenance provides the safest and in the long run, the most economical avenue to the maximum level of destruction of organic hazardous wastes.

Installation and Sampling of Observation Wells and Analyses of Water From the Shallow Aquifer at Selected Waste-Disposal Sites in the Memphis Area, Tennessee

DTIC Science & Technology

1989-01-01

water-table aquifer. This aquifer is made up chiefly of the alluvium and fluvial (terrace) deposits of Quaternary age , but locally may include sand in...the uppermost part of the Jackson Formation and Claiborne Group of Tertiary age . Water samples were collected from these 10 wells and from two...been identified as having received unknown quantities and types of industrial wastes (Waste Age , 1979, p. 54, 56). These sites are the (1) Belleuue

Small-Scale Waste-to-Energy Technology for Contingency Bases

DTIC Science & Technology

2012-05-24

Expedient, No Waste Sorting Technology Readiness Level High Fuel Demand Water Required Steam Infrastructure Required Air Emissions Gasification ...Full gasification system • Costs $26K • GM Industrial Engine (GM 4 Cylinder, 3.00 L) • MeccAlte Generator Head • Imbert type downdraft reactor...Solid waste volume reduction − Response to waste streams  biomass , refuse-derived fuel, shredded waste − Operation and maintenance requirements

Method for processing aqueous wastes

DOEpatents

Pickett, J.B.; Martin, H.L.; Langton, C.A.; Harley, W.W.

1993-12-28

A method is presented for treating waste water such as that from an industrial processing facility comprising the separation of the waste water into a dilute waste stream and a concentrated waste stream. The concentrated waste stream is treated chemically to enhance precipitation and then allowed to separate into a sludge and a supernate. The supernate is skimmed or filtered from the sludge and blended with the dilute waste stream to form a second dilute waste stream. The sludge remaining is mixed with cementitious material, rinsed to dissolve soluble components, then pressed to remove excess water and dissolved solids before being allowed to cure. The dilute waste stream is also chemically treated to decompose carbonate complexes and metal ions and then mixed with cationic polymer to cause the precipitated solids to flocculate. Filtration of the flocculant removes sufficient solids to allow the waste water to be discharged to the surface of a stream. The filtered material is added to the sludge of the concentrated waste stream. The method is also applicable to the treatment and removal of soluble uranium from aqueous streams, such that the treated stream may be used as a potable water supply. 4 figures.

Industrial release of fluoroquinolones (FQs) in the waste water bodies with their associated ecological risk in Pakistan.

PubMed

Riaz, Luqman; Mahmood, Tariq; Kamal, Atif; Shafqat, Mateen; Rashid, Audil

2017-06-01

The unchecked production and use of fluoroquinolones (FQs) for the treatment of infections in human and livestock has increased in Pakistan, which resulted in large amount of antibiotics in water bodies. In the current study, the prevalence and associated ecological risk of three FQs were investigated in waste-water bodies and sludge samples of Kahuta and Hattar industrial zones. The average concentrations of ciprofloxacin (CIP), enrofloxacin (ENR) and levofloxacin (LEV) in the waste-water samples were slightly higher in Kahuta (i.e. 58, 32.9, and 36.7μgL -1 respectively), than those in Hattar sites (i.e. 42.1, 41.2, and 48.9μgL -1 respectively). However, the concentrations of CIP, ENR and LEV in the sludge samples were significantly higher (i.e. 159; 153 and 164μgkg -1 respectively) in Hattar sites, compared to those in Kahuta sites (i.e. 129, 58 and 91μgkg -1 respectively). The uses of FQs in the health sector resulted in water pollution and poses the ecological risk to aquatic organisms. The individual risk associated with CIP was highest in Kahuta industrial sites for green algae ranging (2900-9100) followed by M. aeruginosa (5800-18200), cyanobacteria (580-18204) and invertebrates (24.2-75.8). These values suggested that the prevalence of antibiotics in the waste-disposal sites could be potential risk for the aquatic ecosystem, and harmful to biodiversity. Copyright © 2017 Elsevier B.V. All rights reserved.

Activated-charcoal filters: water treatment, pollution control, and industrial applications. January 1970-July 1988 (citations from the US Patent data base). Report for January 1970-July 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This bibliography contains citations of selected patents concerning activated-charcoal filters and their applications in water treatment, pollution control, and industrial processes. Filtering methods and equipment for air and water purification, industrial distillation and extraction, industrial leaching, and filtration of toxic gases and pollutants are described. Applications include drinking water purification, filtering beverages, production of polymer materials, solvent and metal recovery, swimming pool filtration, waste conversion, automobile fuel and exhaust systems, and footwear deodorizing. (Contains 129 citations fully indexed and including a title list.)

Agriculture: Nutrient Management and Fertilizer

EPA Pesticide Factsheets

Fertilizers and soil amendments can be derived from raw materials, composts and other organic matter, and wastes, such as sewage sludge and certain industrial wastes. Overuse of fertilizers can result in contamination of surface water and groundwater.

Ternary liquid-liquid equilibria for the phenolic compounds extraction from artificial textile industrial waste

NASA Astrophysics Data System (ADS)

Fardhyanti, Dewi Selvia; Prasetiawan, Haniif; Hermawan, Sari, Lelita Sakina

2017-03-01

Liquid waste in textile industry contains large amounts of dyes and chemicals which are capable of harming the environment and human health. It is due to liquid waste characteristics which have high BOD, COD, temperature, dissolved and suspended solid. One of chemical compound which might be harmful for environment when disposed in high concentration is phenol. Currently, Phenol compound in textile industrial waste has reached 10 ppm meanwhile maximum allowable phenol concentration is not more than 0.2 ppm. Otherwise, Phenol also has economic value as feedstock of plastic, pharmaceutical and cosmetic industry. Furthermore, suitable method to separate phenol from waste water is needed. In this research, liquid - liquid extraction method was used with extraction time for 70 minutes. Waste water sample was then separated into two layers which are extract and raffinate. Thereafter, extract and raffinate were then tested by using UV-Vis Spectrophotometer to obtained liquid - liquid equilibrium data. Aim of this research is to study the effect of temperature, stirring speed and type of solvent to obtain distribution coefficient (Kd), phenol yield and correlation of Three-Suffix Margules model for the liquid - liquid extraction data equilibrium. The highest extraction yield at 80.43 % was found by using 70% methanol as solvent at extraction temperature 50 °C with stirring speed 300 rpm, coefficient distribution was found 216.334. From this research it can be concluded that Three-Suffix Margules Model is suitable to predict liquid - liquid equilibrium data for phenol system.

Ecotoxicological water assessment of an estuarine river from the Brazilian Northeast, potentially affected by industrial wastewater discharge.

PubMed

de Melo Gurgel, Piatã; Navoni, Julio Alejandro; de Morais Ferreira, Douglisnilson; do Amaral, Viviane Souza

2016-12-01

Water pollution generated by industrial effluents discharge is a threat to the maintenance of aquatic ecosystems and human development. The Jundiai River estuarine, located in Northeast Brazil, receives an industrial pretreated effluent load from the city of Macaíba/RN/Brazil. The present study aimed to assess the water quality of this water reservoir through i) physicochemical characterization, ii) quantification of metal concentration and iii) by an ecotoxicological assessment carried out using Mysidopsis juniae and Pomacea lineata. The study was performed throughout the period comprising May to September 2014. Physicochemical variables such as chloride, total solids and electrical conductivity presented values in the waste discharge point, significantly different with those located out of the waste releasing point. Apart from that, metal concentration showed variable behavior throughout the monitored period. Levels of Al, Fe, Cu, Cd, Cr, Ni, Pb and Ag were over the considered guidelines. Both natural and anthropogenic sources seem to be involved in the resulting environmental scenario. A reduction in the fecundity rate (using Mysidopsis juniae) along with an increase in mortality rate (in both species) was observed ratifying the presence of toxic substances in this water reservoir. Moreover, a correlation analysis stated an association of the aforementioned toxicological effects with the delivery of industrial waste products. The ecotoxicological assessment performed highlighted the presence of toxic substance/s in water from the Jundiai River. Especially as a consequence of industrial activity, a fact that might threaten the bioma and, therefore, the human health of the population settled in the studied region. Copyright © 2016 Elsevier B.V. All rights reserved.

Supercritical water oxidation of dioxins and furans in waste incinerator fly ash, sewage sludge and industrial soil.

PubMed

Zainal, Safari; Onwudili, Jude A; Williams, Paul T

2014-08-01

Three environmental samples containing dioxins and furans have been oxidized in the presence of hydrogen peroxide under supercritical water oxidation conditions. The samples consisted of a waste incinerator fly ash, sewage sludge and contaminated industrial soil. The reactor system was a batch, autoclave reactor operated at temperatures between 350 degrees C and 450degrees C, corresponding to pressures of approximately 20-33.5 MPa and with hydrogen peroxide concentrations from 0.0 to 11.25 vol%. Hydrogen peroxide concentration and temperature/pressure had a strong positive effect on the oxidation of dioxins and furans. At the highest temperatures and pressure of supercritical water oxidation of 4500C and 33.5 MPa and with 11.25 vol% of hydrogen peroxide, the destruction efficiencies of the individual polychlorinated dibenzo-p-dioxins/polychlorinated dibenzofurans (PCDD/PCDF) isomers were between 90% and 99%. There did not appear to be any significant differences in the PCDD/PCDF destruction efficiencies in relation to the different sample matrices of the waste incinerator fly ash, sewage sludge and contaminated industrial soil.

[The influence of the oil and gas industry on environmental safety and population health in the Khanty-Mansiĭskiĭ Region - Iugra].

PubMed

Samutin, N M; Vorob'ev, V O; Butorin, N N

2013-01-01

Production activities of oil and gas industry plants are related to technogenic impact on the environment, which has a high environmental risk. This is associated with low levels of environmental orientation of sheer technological processes of exploration and exploitation of hydrocarbons and also used in this technical means, materials and chemical reagents. The main pollutants that deteriorate the toxic characteristics of drilling waste, are the most likely drilling fluids, mud flush agents and chemicals, which enter into their composition. Existing methods of disposal of drilling wastes are not effective, the technology of their use is often violated. Dumping drilling waste into water bodies and burying toxic waste in water protection areas under the guise of processed waste has been observed. In the region there are significantly exceeded the national average values rate of morbidity of allergic, cardiovascular, pulmonary and cancer diseases, mediated by environmental factors and new monofactorial and multifactorial diseases appear.

Watershed Management in the United States

EPA Science Inventory

A watershed approach provides an effective framework for dealing with water resources challenges. Watersheds provide drinking water, recreation, and ecological habitat, as well as a place for waste disposal, a source of industrial cooling water, and navigable inland water transpo...

[Investigation on acute nitrite poisoning in Yangjiang city, Guangdong province, China].

PubMed

Yu, Hongjie; Luo, Huiming; Lu, Xirong; Song, Qubo; Fan, Zifan

2002-12-01

To determine the cause of acute poisoning occurred in a factory in Yangjiang city, Guangdong province. In a cross-sectional study, interviews were conducted with the administrators of the factory and the local physician. A review was conducted on the water system used for industrial purposes and a separate system used by workers for drinking water. Treatment and discharge of industrial waste water were examined. Face-to-face interview was conducted to identify risk of exposure for illness among workers. A total number of 36 cases were identified in the plant and the attack rate was 16.4% (36/220). The incubation period (time between drinking polluted water and the onset of symptoms) had a median of 90 minutes (range: 30 - 230 minutes). Consuming water at the factory increased the attack rate and a dose-response effect was identified (chi(2)(trend) = 79.115, P < 0.01). The nitrite content of residuals in drinking water exceeded the WHO standard (1 ppm). The accident of acute poisoning was due to drinking water contaminated with sodium nitrite. The prevention of drinking water contaminated by toxic chemicals like sodium nitrite, and the design of industrial and potable water supply system need to be carefully reviewed. Regulations should be developed and enforced to minimize the impact of industrial waste water discharges to guarantee the access to clean drinking water.

Importance of biological systems in industrial waste treatment potential application to the space station

NASA Technical Reports Server (NTRS)

Revis, Nathaniel; Holdsworth, George

1990-01-01

In addition to having applications for waste management issues on planet Earth, microbial systems have application in reducing waste volumes aboard spacecraft. A candidate for such an application is the space station. Many of the planned experiments generate aqueous waste. To recycle air and water the contaminants from previous experiments must be removed before the air and water can be used for other experiments. This can be achieved using microorganisms in a bioreactor. Potential bioreactors (inorganics, organics, and etchants) are discussed. Current technologies that may be applied to waste treatment are described. Examples of how biological systems may be used in treating waste on the space station.

Coal-water slurries containing petrochemicals to solve problems of air pollution by coal thermal power stations and boiler plants: An introductory review.

PubMed

Dmitrienko, Margarita A; Strizhak, Pavel A

2018-02-01

This introductory study presents the analysis of the environmental, economic and energy performance indicators of burning high-potential coal water slurries containing petrochemicals (CWSP) instead of coal, fuel oil, and natural gas at typical thermal power stations (TPS) and a boiler plant. We focus on the most hazardous anthropogenic emissions of coal power industry: sulfur and nitrogen oxides. The research findings show that these emissions may be several times lower if coal and oil processing wastes are mixed with water as compared to the combustion of traditional pulverized coal, even of high grades. The study focuses on wastes, such as filter cakes, oil sludge, waste industrial oils, heavy coal-tar products, resins, etc., that are produced and stored in abundance. Their deep conversion is very rare due to low economic benefit. Effective ways are necessary to recover such industrial wastes. We present the cost assessment of the changes to the heat and power generation technologies that are required from typical power plants for switching from coal, fuel oil and natural gas to CWSPs based on coal and oil processing wastes. The corresponding technological changes pay off after a short time, ranging from several months to several years. The most promising components for CWSP production have been identified, which provide payback within a year. Among these are filter cakes (coal processing wastes), which are produced as a ready-made coal-water slurry fuel (a mixture of flocculants, water, and fine coal dust). These fuels have the least impact on the environment in terms of the emissions of sulfur and nitrogen oxides as well as fly ash. An important conclusion of the study is that using CWSPs based on filter cakes is worthwhile both as the main fuel for thermal power stations and boiler plants and as starting fuel. Copyright © 2017 Elsevier B.V. All rights reserved.

Bacterial Cellulose Production from Industrial Waste and by-Product Streams

PubMed Central

Tsouko, Erminda; Kourmentza, Constantina; Ladakis, Dimitrios; Kopsahelis, Nikolaos; Mandala, Ioanna; Papanikolaou, Seraphim; Paloukis, Fotis; Alves, Vitor; Koutinas, Apostolis

2015-01-01

The utilization of fermentation media derived from waste and by-product streams from biodiesel and confectionery industries could lead to highly efficient production of bacterial cellulose. Batch fermentations with the bacterial strain Komagataeibacter sucrofermentans DSM (Deutsche Sammlung von Mikroorganismen) 15973 were initially carried out in synthetic media using commercial sugars and crude glycerol. The highest bacterial cellulose concentration was achieved when crude glycerol (3.2 g/L) and commercial sucrose (4.9 g/L) were used. The combination of crude glycerol and sunflower meal hydrolysates as the sole fermentation media resulted in bacterial cellulose production of 13.3 g/L. Similar results (13 g/L) were obtained when flour-rich hydrolysates produced from confectionery industry waste streams were used. The properties of bacterial celluloses developed when different fermentation media were used showed water holding capacities of 102–138 g·water/g·dry bacterial cellulose, viscosities of 4.7–9.3 dL/g, degree of polymerization of 1889.1–2672.8, stress at break of 72.3–139.5 MPa and Young’s modulus of 0.97–1.64 GPa. This study demonstrated that by-product streams from the biodiesel industry and waste streams from confectionery industries could be used as the sole sources of nutrients for the production of bacterial cellulose with similar properties as those produced with commercial sources of nutrients. PMID:26140376

Bacterial Cellulose Production from Industrial Waste and by-Product Streams.

PubMed

Tsouko, Erminda; Kourmentza, Constantina; Ladakis, Dimitrios; Kopsahelis, Nikolaos; Mandala, Ioanna; Papanikolaou, Seraphim; Paloukis, Fotis; Alves, Vitor; Koutinas, Apostolis

2015-07-01

The utilization of fermentation media derived from waste and by-product streams from biodiesel and confectionery industries could lead to highly efficient production of bacterial cellulose. Batch fermentations with the bacterial strain Komagataeibacter sucrofermentans DSM (Deutsche Sammlung von Mikroorganismen) 15973 were initially carried out in synthetic media using commercial sugars and crude glycerol. The highest bacterial cellulose concentration was achieved when crude glycerol (3.2 g/L) and commercial sucrose (4.9 g/L) were used. The combination of crude glycerol and sunflower meal hydrolysates as the sole fermentation media resulted in bacterial cellulose production of 13.3 g/L. Similar results (13 g/L) were obtained when flour-rich hydrolysates produced from confectionery industry waste streams were used. The properties of bacterial celluloses developed when different fermentation media were used showed water holding capacities of 102-138 g · water/g · dry bacterial cellulose, viscosities of 4.7-9.3 dL/g, degree of polymerization of 1889.1-2672.8, stress at break of 72.3-139.5 MPa and Young's modulus of 0.97-1.64 GPa. This study demonstrated that by-product streams from the biodiesel industry and waste streams from confectionery industries could be used as the sole sources of nutrients for the production of bacterial cellulose with similar properties as those produced with commercial sources of nutrients.

The French Mess Nucleaire

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, M.B.

1994-07-01

Nuclear weapons production has contaminated parts of France, and measures to counter this contamination may be as much cover-up as cleanup. The nuclear weapons industry is trying to remedy some of the problems it created. But until France lifts military secrecy from weapons production matters that affect the environment, the public has no way to gauge the cleanup. No institution outside the Atomic Energy Commission (CEA) and the Ministry of Defense has control over waste disposal, decontamination, and dismantlement at military nuclear sites. The major generators of weapons production waste in France are the CEA and Cogema, one of itsmore » many subsidiaries. Regular operations in military production sites produce environmental contamination. The authors also discuss some accidents causing further contamination. The clean-up measures that the industry is known to be taking, diluting the waste and minimizing the amount of waste, are suspect. The earth`s atmosphere has been considered a prime medium for diluting waste by open air burning of radioactive materials. Releases of mercury to the atmosphere, 260 kilograms per year as of 1984, contributed to water pollution as rain washed the mercury out of the air. Ocean dumping was the CEA`s answer to disposal of sold as well as liquid wastes. Injection liquids into the soil has been a temptation at sites not near substantial bodies of water. Burial of solid wastes has been common. The nuclear industry and the military must make public where and in what form wastes are stored. They must allow independent experts and institutions to examine their research, fabrication, and waste disposal sites. 48 refs.« less

Effects of three phosphate industrial sites on ground-water quality in central Florida, 1979 to 1980

USGS Publications Warehouse

Miller, R.L.; Sutcliffe, Horace

1984-01-01

Geologic, hydrologic, and water quality data and information on test holes collected in the vicinity of gypsum stack complexes at two phosphate chemical plants and one phosphatic clayey waste disposal pond at a phosphate mine and beneficiation plant in central Florida are presented. The data were collected from September 1979 to October 1980 at the AMAX Phosphate, Inc. chemical plant, Piney Point; the USS Agri-Chemicals chemical plant, Bartow; and the International Minerals and Chemical Corporation Clear Springs mine, Bartow. Approximately 5,400 field and laboratory water quality determinations on water samples collected from about 100 test holes and 28 surface-water , 5 rainfall, and other sampling sites at phosphate industry beneficiation and chemical plant waste disposal operations are tabulated. Maps are included to show sampling sites. (USGS)

A DECISION SUPPORT TOOL (DST) FOR DISPOSAL OF ...

EPA Pesticide Factsheets

Symposium Paper AFTER A BUILDING OR WATER TREATMENT/DISTRIBUTION FACILITY HAS GONE THROUGH DECONTAMINATION ACTIVITIES FOLLOWING A CONTAMINATION EVENT WITH CHEMICAL/BIOLOGICAL WARFARE AGENTS OR TOXIC INDUSTRIAL CHEMICAL, THERE WILL BE A SIGNIFICANT AMOUNT OF RESIDUAL MATERIAL AND WASTE TO BE DISPOSED. A CONTAMINATION EVENT COULD OCCUR FROM TERRORIST ACTIVITY OR FROM A NATURAL DISASTER SUCH AS THE RECENT HURRICANE EVENTS IN THE GULF COAST WHERE MOLD AND POLLUTANTS FROM DAMAGED CHEMICAL AND INDUSTRIAL FACILITIES HAVE RESULTED IN SIGNIFICANT QUANTITIES OF CONTAMINATED MATERIALS. IT iS LIKELY THAT MUCH OF THIS MATERIAL WILL BE DISPOSED OF IN PERMITTED LANDFILLS OR HIGH TEMPERATURE THERMAL INCINERATION FACILITIES. DATA HAS BEEN COLLECTED FROM THE OPEN LITERATURE, FROM STATE AND FEDERAL REGULATORY AGENCIES, AND FROM WASTE MANAGEMENT AND WATER UTILITY INDUSTRY STAKEHOLDER GROUPS, TO DEVELOP TECHNICAL GUIDANCE FOR DISPOSAL OF THESe RESIDUES. THE INFORMATION BECOMES AVAILABLE, AND OLD INFORMATION (SUCH AS CONTACT INFORMATION FOR KEY PERSONNEL) CHANGES. THE PRiMARY AUDIENCE FOR THIS TOOL WILL BE: 1) EMERGENCY RESPONSE AUTHORITIES WHO HAVE TO DECIDE THE MOST APPROPRIATE DECONTAMINATION METHODS AND DISPOSAL OF THE RESULTING RESIDUES; 2)STATE AND LOCAL PERMITTING AGENCIES, WHO HAVE TO MAKE DECISIONS ABOUT WHICH FACILITIES WILL BE ALLOWED TO DISPOSE OF THE MATERIALS: AND 3) THE WASTE MANAGEMENT AND WATER UTILITY INDUSTRY, THAT NEEDS TO SAFELY DISPOSE OF DECONTAMINATION RESIDUE

Environmental assessment for the proposed effluent limitations guidelines, pretreatment standards, and new source performance standards for the centralized waste treatment industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-12-01

This report assesses the water quality related benefits that would be expected if the US Environmental Protection Agency (EPA) adopts the proposed effluent limitations, guidelines and pretreatment standards for the Centralized Waste Treatment (CWT) Industry. EPA estimates that under baseline conditions 205 CWT facilities discharge approximately 5.22 million lbs/year of metal and organic pollutants.

Activated charcoal filters: Water treatment, pollution control, and industrial applications. (Latest citations from the Patent Bibliographic database with exemplary claims. ) Published Search

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The bibliography contains citations of selected patents concerning activated charcoal filters and their applications in water treatment, pollution control, and industrial processes. Filtering methods and equipment for air and water purification, industrial distillation and extraction, industrial leaching, and filtration of toxic materials and contaminants are described. Applications include drinking water purification, filtering beverages, production of polymer materials, solvent and metal recovery, waste conversion, automotive fuel and exhaust systems, swimming pool filtration, tobacco smoke filters, kitchen ventilators, medical filtration treatment, and odor absorbing materials. (Contains 250 citations and includes a subject term index and title list.)

The use of sub-critical water hydrolysis for the recovery of peptides and free amino acids from food processing wastes. Review of sources and main parameters.

PubMed

Marcet, Ismael; Álvarez, Carlos; Paredes, Benjamín; Díaz, Mario

2016-03-01

Food industry processing wastes are produced in enormous amounts every year, such wastes are usually disposed with the corresponding economical cost it implies, in the best scenario they can be used for pet food or composting. However new promising technologies and tools have been developed in the last years aimed at recovering valuable compounds from this type of materials. In particular, sub-critical water hydrolysis (SWH) has been revealed as an interesting way for recovering high added-value molecules, and its applications have been broadly referred in the bibliography. Special interest has been focused on recovering protein hydrolysates in form of peptides or amino acids, from both animal and vegetable wastes, by means of SWH. These recovered biomolecules have a capital importance in fields such as biotechnology research, nutraceuticals, and above all in food industry, where such products can be applied with very different objectives. Present work reviews the current state of art of using sub-critical water hydrolysis for protein recovering from food industry wastes. Key parameters as reaction time, temperature, amino acid degradation and kinetic constants have been discussed. Besides, the characteristics of the raw material and the type of products that can be obtained depending on the substrate have been reviewed. Finally, the application of these hydrolysates based on their functional properties and antioxidant activity is described. Copyright © 2016 Elsevier Ltd. All rights reserved.

Cultivation of Microalgae Chlorella sp on Fresh Water and Waste Water of Tofu Industry

NASA Astrophysics Data System (ADS)

Widayat; Philia, John; Wibisono, Jessica

2018-02-01

Chlorella sp. is a microalgae that potential for food supplement, pharmaceuticals, animal feed, aqua culture and cosmetics. Chlorella sp. commonly growth in sea water. Indonesia as a producer of tofu generated more liquid waste. Nutrient that contained in the tofu wastewater are very useful for the production of microalgae. Cultivation carried out for 7 days at different percent volume of tofu liquid waste showed that the more volume of tofu liquid waste make them longer process decipherment of polymer compounds in the waste, that's make the growth rate of Chlorella sp. are slowness. Variable of10%V has the fastest growth rate. While, 90% v/v variable has the highest concentration of algae. It shows that Chlorella sp. better to grows in tofu wastewater than seawater.

Using Summer Faculty-Student Consultant Teams to Solve Industrial Problems

ERIC Educational Resources Information Center

Michelsen, Donald L.; And Others

1977-01-01

Describes a three-week, faculty-student summer project involving the study of waste-water treatment of refinery effluents. Discusses the use of such projects to aid industry in analyzing their problems. (MLH)

Hybrid Membrane System for Industrial Water Reuse

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2016-08-01

This factsheet describes a project that developed and demonstrated a new hybrid system for industrial wastewater treatment that synergistically combines a forward osmosis system with a membrane distillation technology and is powered by waste heat.

Water Pollution, Causes and Cures.

ERIC Educational Resources Information Center

Manufacturing Chemists Association, Washington, DC.

This commentary on sources of water pollution and water pollution treatment systems is accompanied by graphic illustrations. Sources of pollution such as lake bottom vegetation, synthetic organic pollutants, heat pollution, radioactive substance pollution, and human and industrial waste products are discussed. Several types of water purification…

[Migration of industrial radionuclides in soils and benthal deposits at the coastal margins of the temporary waste storage facility (TWSF) of the Northwest Center for Radioactive Waste Management (SevRAO) and its influence on the possible contamination of the sea offshore waters].

PubMed

Filonova, A A; Seregin, V A

2014-01-01

For obtaining the integral information about the current radiation situation in the sea offshore waters of the temporary waste storage facility (TWSF) of the Northwest Center for Radioactive Waste Management "SevRAO" in the Andreeva Bay and in the settle Gremikha with a purpose of a comprehensive assessment of its condition there was performed radiation-ecological monitoring of the adjacent sea offshore waters of the TWSF. It was shown that in the territory of industrial sites of the TWSF as a result of industrial activity there are localized areas of pollution by man-made radionuclides. As a result of leaching of radionuclides by tidal stream, snowmelt and rainwater radioactive contamination extends beyond the territory of the sanitary protection zone and to the coastal sea offshore waters. To confirm the coastal pollution of the sea offshore waters the levels of mobility of 90Sr and 137Cs in environmental chains and bond strength of them with the soil and benthal deposits were clarified by determining with the method of detection of the forms of the presence of radionuclides in these media. There was established a high mobility of 137Cs and 90Sr in soils and benthal deposits (desorption coefficient (Kd) of 137Cs and 90Sr (in soils - 0.56 and 0.98), in the sediments - 0.82). The migration of radionuclides in environmental chains can lead to the contamination of the environment, including the sea offshore waters.

Industrial waste water in Bangkok, Thailand: Definitional mission report. Export trade information

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pfrang, W.

A definitional mission visited Thailand between February 1 and 7, 1992 to study the market opportunities for US manufacturers in providing pollution control equipment. Thailand presently lacks industrial machinery required for pollution control equipment. Consequently, this equipment must be imported for both industrial and municipal waste treatment facilities. The US has both the applicable technology and manufactured goods to serve the market. There is, however, stiff competition from Europe and especially Japan, who offer financial assistance at preferential rates for these types of projects.

PRETREATMENT OF THE COMBINED INDUSTRIAL-DOMESTIC WASTEWATERS OF HAGERSTOWN, MARYLAND. VOLUME I

EPA Science Inventory

The sewage treatment plant of the city of Hagerstown, Maryland--a manufacturing city with about 130 industrial firms, which are classified in more than 25 different product categories--receives for treatment domestic sewage and a diversity of industrial waste and process waters. ...

PRETREATMENT OF THE COMBINED INDUSTRIAL-DOMESTIC WASTEWATERS OF HAGERSTOWN, MARYLAND. APPENDIX. VOLUME II

EPA Science Inventory

The sewage treatment plant of the city of Hagerstown, Maryland--a manufacturing city with about 130 industrial firms, which are classified in more than 25 different product categories--receives for treatment domestic sewage and a diversity of industrial waste and process waters. ...

STATE OF THE ART: WASTEWATER MANAGEMENT IN THE BEVERAGE INDUSTRY

EPA Science Inventory

The general purpose of this paper is to investigate, through the literature, the water pollution impact caused by the wastes from the beverage industry and the methods available to combat the associated problems. The size of each industry is discussed along with production proces...

Hazardous Waste Management: A View to the New Century, 2001.

ERIC Educational Resources Information Center

Burton, Gwen

Like many parts of the United States, Colorado is facing a significant hazardous waste problem. Radioactive and chemical wastes generated by the Rocky Flats Nuclear Plant, the toxic Lowry Land Fill Site, industrial dumps, and heavy land and air traffic contribute to water, land, and air pollution in the state. As part of a statewide response…

40 CFR 52.222 - Negative declarations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... County Air Pollution Control District. (i) Industrial Wastewater, Plastic Parts Coating: Business... Pollution Control District. (i) Aerospace Coatings; Industrial Waste Water Treatment; Plastic Parts Coating..., 2011. (a) The following air pollution control districts submitted negative declarations for volatile...

Comprehensive Planning for Classification and Disposal of Solid Waste at the Industrial Parks regarding Health and Environmental Impacts

PubMed Central

Rahmani Samani, Bahareh

2014-01-01

The aim of this study is the comprehensive planning for integrated management of solid waste at the industrial parks. The share of each industrial group including food, metal, chemical, non-metallic minerals, textile, electrical and electronical, and cellulose industries were 48.2, 14.9, 6.7, 22, 0.9, 0.6, and 6.5 percent, respectively. The results showed that nearly half of total industrial waste produced from the range of biological materials are biodegradable and discharging them without observing environmental regulations leads to short-term pollution and nuisance in the acceptor environment. Also some parts of case study waste were recyclable which is considerable from viewpoint of economical and environmental pollution. Long-term impacts will appear due to improper site selection of disposal from the spatial standpoint. In this way, an approach for site selection using several socioeconomic, physical, and environmental criteria based on multicriteria decision making model (MCDM) is introduced. Health risks and environment pollution such as soil and surface water may be done. It is essential to revise the studied industries layout, particularly those units which produce special waste which should be more cautious. Also stricter enforcement is required as an effective step in reducing the harmful impacts of it. PMID:24688552

Comprehensive planning for classification and disposal of solid waste at the industrial parks regarding health and environmental impacts.

PubMed

Hashemi, Hassan; Pourzamani, Hamidreza; Rahmani Samani, Bahareh

2014-01-01

The aim of this study is the comprehensive planning for integrated management of solid waste at the industrial parks. The share of each industrial group including food, metal, chemical, non-metallic minerals, textile, electrical and electronical, and cellulose industries were 48.2, 14.9, 6.7, 22, 0.9, 0.6, and 6.5 percent, respectively. The results showed that nearly half of total industrial waste produced from the range of biological materials are biodegradable and discharging them without observing environmental regulations leads to short-term pollution and nuisance in the acceptor environment. Also some parts of case study waste were recyclable which is considerable from viewpoint of economical and environmental pollution. Long-term impacts will appear due to improper site selection of disposal from the spatial standpoint. In this way, an approach for site selection using several socioeconomic, physical, and environmental criteria based on multicriteria decision making model (MCDM) is introduced. Health risks and environment pollution such as soil and surface water may be done. It is essential to revise the studied industries layout, particularly those units which produce special waste which should be more cautious. Also stricter enforcement is required as an effective step in reducing the harmful impacts of it.

Sorption of PFOA and PFOS to Aquifer Sediment

EPA Science Inventory

During its years of operation, the Washington County Sanitary Landfill near St. Paul, Minnesota accepted both municipal and industrial solid waste. Several years of ground water monitoring performed by the MPCA indicates that, some of the waste disposed of at this landfill contai...

THE SOURCES, FATE AND HAZARDS OF MUTAGENS IN SURFACE WATERS

EPA Science Inventory

A variety of industrial, domestic and agricultural wastes are discharged into rivers, lakes, streams, and estuaries. In some instances, these wastes contain substances that are capable I of permanently altering the genetic material of exposed organisms (i.e., they are mutagens). ...

Biosorption of heavy metals from industrial waste water by Geobacillus thermodenitrificans.

PubMed

Chatterjee, S K; Bhattacharjee, I; Chandra, G

2010-03-15

The metal binding capacity of the thermophilic bacteria Geobacillus thermodenitrificans isolated from Damodar river, India was assessed using synthetic metal solutions and industrial waste water. Biosorption preference of dead biomass of G. thermodenitrificans for the synthetic metal solutions was in the following order Fe(+3)>Cr(+3)>Co(+2)>Cu(+2)>Zn(+2)>Cd(+2)>Ag(+)>Pb(+2). It reduced the concentration of Fe(+3) (91.31%), Cr(+3) (80.80%), Co(+2) (79.71%), Cu(+2) (57.14%), Zn(+2) (55.14%), Cd(+2) (49.02%), Ag(+) (43.25%) and Pb(+2) (36.86%) at different optimum pH within 720 min. When this strain was applied in the industrial waste water biosorption preference was in the following order Fe(+3)>Cr(+3)>Cd(+2)>Pb(+2)>Cu(+2)>Co(+2)>Zn(+2)>Ag(+) and concentrations reduced up to 43.94% for Fe(+3), 39.2% for Cr(+3), 35.88% for Cd(+2), 18.22% for Pb(+2), 13.03% for Cu(+2), 11.43% for Co(+2), 9.02% for Zn(+2) and 7.65% for Ag(+) within 120 min. (c) 2009 Elsevier B.V. All rights reserved.

Soil and solid poultry waste nutrient management and water quality.

PubMed

Chapman, S L

1996-07-01

Concerns about the impacts of nitrogen, phosphorus, and pathogens on surface and ground water quality has forced the poultry industry to implement voluntary waste management guidelines for use by growers. In some states, animal waste guidelines are being enforced by regulatory agencies. Strategies that growers may use to properly dispose of poultry waste include: 1) local land application as a fertilizer; 2) offsite marketing for use as a fertilizer or soil amendment, feed additive, or energy source; and 3) chemical additives that will immobilize nitrogen and phosphorus in the manure or litter. If properly followed, these and other innovative strategies should be adequate to protect surface and ground water quality without adversely affecting the economics of poultry production.

Waste-water characterization and hazardous-waste technical assistance survey, Bergstrom AFB tTxas. Final report, 6-15 March 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hedgecock, N.S.

1990-01-01

At the request of 67 Combat Support Group/DEEV the Air Force Occupational and Environmental Health Laboratory conducted a waste-water characterization and hazardous-waste technical assistance survey at Bergstrom AFB (BAFB) from 6-15 Mar 89. The scope of the waste-water survey was to characterize the effluent exiting the base and the effluent from 23 industrial facilities and 10 food-serving facilities. The scope of the hazardous-waste survey was to address hazardous-waste-management practices and explore opportunities for hazardous waste minimization. Specific recommendations from the survey include: (1) Accompany City of Austin personnel during waste-water sampling procedures; (2) Sample at the manhole exiting the mainmore » lift station rather than at the lift station wet well; (3) Split waste-water samples with the City of Austin for comparison of results; (4) Ensure that oil/water separators and grease traps are functioning properly and are cleaned out regularly; (5) Limit the quantity of soaps and solvents discharged down the drain to the sanitary sewer; (6) Establish a waste disposal contract for the removal of wastes in the Petroleum Oils and Lubricants underground storage tanks. (7) Remove, analyze, and properly dispose of oil contaminated soil from accumulation sites. (8) Move indoors or secure, cover, and berm the aluminum sign reconditioning tank at 67 Civil Engineering Squadron Protective Coating. (9) Connect 67 Combat Repair Squadron Test Cell floor drains to the sanitary sewer.« less

The Conversion and Sustainable Use of Alumina Refinery Residues: Global Solution Examples

NASA Astrophysics Data System (ADS)

Fergusson, Lee

This paper introduces current industry best practice for the conversion of alumina refinery residues (or "red mud") from hazardous waste to benign, inert material. The paper will examine four neutralization methods and Basecon Technology, a sustainable conversion process. The paper will consider ways through which this converted material can be combined and processed for sustainable applications in the treatment of hazardous waste streams (such as industrial wastewater and sludges, biosolids, and CCA wastes), contaminated brownfield sites, and mine site wastes. Recent discoveries and applications, such as the successful treatment of high levels of radium in drinking water in the USA, will also be discussed. Examples of global solutions and their technical merits will be assessed.

Effects of Wastes from the Brewing Industry in Lightweight Aggregates Manufactured with Clay for Green Roofs.

PubMed

Farías, Romina D; Martínez García, Carmen; Cotes Palomino, Teresa; Martínez Arellano, Myriam

2017-05-15

This study investigates the effects of sieved wastes generated from the brewing industry on lightweight aggregates manufactured with clay. Sludge from a wastewater treatment plant, bagasse and diatomaceous earth were used to obtain the samples. These wastes are usually dumped in landfills, but the current increase in restrictions on dumping and interest in improving the environment make our proposal for gaining value from these wastes a significant contribution. Laboratory tests show that the new aggregate has low bulk density and increased water absorption and porosity. The thermographic camera results provide evidence that new aggregates have significant insulating properties and are suitable for use on green roofs.

Effects of Wastes from the Brewing Industry in Lightweight Aggregates Manufactured with Clay for Green Roofs

PubMed Central

Farías, Romina D.; Martínez García, Carmen; Cotes Palomino, Teresa; Martínez Arellano, Myriam

2017-01-01

This study investigates the effects of sieved wastes generated from the brewing industry on lightweight aggregates manufactured with clay. Sludge from a wastewater treatment plant, bagasse and diatomaceous earth were used to obtain the samples. These wastes are usually dumped in landfills, but the current increase in restrictions on dumping and interest in improving the environment make our proposal for gaining value from these wastes a significant contribution. Laboratory tests show that the new aggregate has low bulk density and increased water absorption and porosity. The thermographic camera results provide evidence that new aggregates have significant insulating properties and are suitable for use on green roofs. PMID:28772892

Effect of kaolin addition on the performance of controlled low-strength material using industrial waste incineration bottom ash.

PubMed

Naganathan, Sivakumar; Razak, Hashim Abdul; Hamid, Siti Nadzriah Abdul

2010-09-01

Incineration of industrial waste produces large quantities of bottom ash which are normally sent to secured landfill, but is not a sustainable solution. Use of bottom ash in engineering applications will contribute to sustainability and generate revenue. One way of using the industrial waste incineration bottom ash is in controlled low-strength material (CLSM). Use of bottom ash in CLSM has problems related to bleeding and excessive strength development and so an additive has to be used to control bleeding and strength development. The main objective of this research is to study the effect of kaolin addition on the performance of CLSM made using industrial waste incineration bottom ash. CLSM mixes were made with bottom ash, cement, and refined kaolin. Various tests were performed on the CLSM in fresh and hardened states including compressive strength, water absorption, California bearing ratio (CBR) and the tests for concentration of leachable substances on the bleed and leachate. The compressive strength of CLSM tested ranged from 0.11 to 9.86 MPa. CBR values ranged from 6 to 46, and water absorption values from 12 to 36%. It was shown that the addition of kaolin delayed the initial setting time of CLSM mixtures, reduced bleeding, lowered the compressive strength, and increased the values of water absorption, sorption, and initial surface absorption. The CLSM tested did not have corrosivity. It was shown that the hardened CLSM was non hazardous, and the addition of kaolin increased the concentration of heavy metals and salts in the bleed and leachate.

World first in high level waste vitrification - A review of French vitrification industrial achievements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brueziere, J.; Chauvin, E.; Piroux, J.C.

2013-07-01

AREVA has more than 30 years experience in operating industrial HLW (High Level radioactive Waste) vitrification facilities (AVM - Marcoule Vitrification Facility, R7 and T7 facilities). This vitrification technology was based on borosilicate glasses and induction-heating. AVM was the world's first industrial HLW vitrification facility to operate in-line with a reprocessing plant. The glass formulation was adapted to commercial Light Water Reactor fission products solutions, including alkaline liquid waste concentrates as well as platinoid-rich clarification fines. The R7 and T7 facilities were designed on the basis of the industrial experience acquired in the AVM facility. The AVM vitrification process wasmore » implemented at a larger scale in order to operate the R7 and T7 facilities in-line with the UP2 and UP3 reprocessing plants. After more than 30 years of operation, outstanding record of operation has been established by the R7 and T7 facilities. The industrial startup of the CCIM (Cold Crucible Induction Melter) technology with enhanced glass formulation was possible thanks to the close cooperation between CEA and AREVA. CCIM is a water-cooled induction melter in which the glass frit and the waste are melted by direct high frequency induction. This technology allows the handling of highly corrosive solutions and high operating temperatures which permits new glass compositions and a higher glass production capacity. The CCIM technology has been implemented successfully at La Hague plant.« less

Activated charcoal filters: Water treatment, pollution control, and industrial applications. October 1970-October 1989 (Citations from the US Patent data base). Report for October 1970-October 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This bibliography contains citations of selected patents concerning activated charcoal filters and their applications in water treatment, pollution control, and industrial processes. Filtering methods and equipment for air and water purification, industrial distillation and extraction, industrial leaching, and filtration of toxic materials and contaminants are described. Applications include drinking water purification, filtering beverages, production of polymer materials, solvent and metal recovery, waste conversion, automotive fuel and exhaust systems, swimming-pool filtration, tobacco-smoke filters, kitchen ventilators, medical filtration treatment, and odor-absorbing materials. (This updated bibliography contains 173 citations, 12 of which are new entries to the previous edition.)

Activated-charcoal filters: Water treatment, pollution control, and industrial applications. January 1970-August 1989 (Citations from the US Patent data base). Report for January 1970-August 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This bibliography contains citations of selected patents concerning activated charcoal filters and their applications in water treatment, pollution control, and industrial processes. Filtering methods and equipment for air and water purification, industrial distillation and extraction, industrial leaching, and filtration of toxic materials and contaminants are described. Applications include drinking-water purification, filtering beverages, production of polymer materials, solvent and metal recovery, waste conversion, automotive fuel and exhaust systems, swimming-pool filtration, tobacco-smoke filters, kitchen ventilators, medical-filtration treatment, and odor absorbing materials. (This updated bibliography contains 161 citations, 32 of which are new entries to the previous edition.)

Waste-water characterization and hazardous-waste technical assistance survey, Mather AFB California. Final report, 28 November-9 December 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, S.P.; Hedgecock, N.S.

1989-10-01

Personnel from the AFOEHL conducted a waste-water characterization and hazardous-waste technical assistance survey at MAFB from 28 Nov to 9 Dec 1988. The scope of this survey was to characterize the waste-water, address hazardous-waste-management practices, and explore opportunities for hazardous waste minimization. The waste water survey team analyzed the base's industrial effluent, effluent from oil/water separators, and storm water. The team performed a shop-by-shop evaluation of chemical-waste-management practices. Survey results showed that MAFB needs to improve its hazardous-waste-management program. Recommendations for improvement include: (1) Collecting two additional grab samples on separate days from the hospital discharge. Analyze for EPA Methodmore » 601 to determine if the grab sample from the survey gives a true indication of what is being discharged. (2) Locate the source and prevent mercury from the hospital from discharging into the sanitary sewer. (3) Dilute the soaps used for cleaning at the Fuels Lab, Building 7060. (4) Investigate the source of chromium from the Photo Lab. (5) Clean out the sewer system manhole directly downgradient from the Photo Lab. (6) Locate the source of contamination in the West Ditch Outfall. (7) Reconnect the two oil/water separators that discharge into the storm sewerage system. (8) Investigate the source of methylene chloride coming on the base. (9) Investigate the source of mercury at Fuel Cell Repair, building 7005.« less

Physico-chemical treatment of liquid waste on an industrial plant for electrocoagulation.

PubMed

Mlakar, Matej; Levstek, Marjetka; Stražar, Marjeta

2017-10-01

Wastewater from washing, oil separators, the metal processing and detergent industries, was tested and treated for treatment of different types of liquid waste at industrial level at Domžale-Kamnik Wastewater Treatment Plant (WWTP). The effect of implementing the electrocoagulation (EC) and flotation processes, respectively, is analysed and includes the duration of the EC implementation, voltage, number of electrodes, and chemical addition, as well as the pH effect and conductivity. The tests were performed not only on various types of liquid waste, but also on different mixtures of liquid waste. Laboratory analysis of the samples before and after EC have shown an effective reduction not only in organic loads in accordance with the COD (chemical oxygen demand) parameter, but also in mineral oil content, toxic metal concentration, and surfactants. The COD in liquid waste from the detergent industry was reduced by 73% and the content of surfactants by 64%. In liquid waste from the metal processing industry, the COD decreased by up to 95%, while the content of toxic metals decreased from 59 to 99%. Similar phenomena were shown in liquid waste from oil separators, where the COD was reduced to 33% and the concentration of mineral oils by 99%. Some of the liquid wastes were mixed together in the ratio 1:1, thus allowing testing of the operation of EC technology in heterogeneous liquid waste, where the final result proved to be effective cleaning as well. After treatment in the process of EC, the limit values of the treated water proved appropriate for discharge into the sewerage system.

Industrial Waste Management Evaluation Model Version 3.1

EPA Pesticide Factsheets

IWEM is a screening level ground water model designed to simulate contaminant fate and transport. IWEM v3.1 is the latest version of the IWEM software, which includes additional tools to evaluate the beneficial use of industrial materials

The environmental problems in urban communities and the protection of the environment in Korea.

PubMed

Kim, I K

1994-07-01

Korea's urban environmental problems, specifically air and water pollution, government environmental policies, and the role of nongovernmental organizations (NGOs) in protecting the environment are described and discussed. Korea's rapid industrialization and urbanization between 1961 and 1985 led to an increased volume of waste and air pollution. Automobiles increased in number from 29,234 in 1961 to 1,113,430 in 1985. In the same period, the number of factories with at least five employees rose from 15,204 to 44,037. The volume of chemical materials and agricultural chemicals dramatically increased. Household wastes in urban areas increased from 26,831 tons per day in 1978 to 61,072 tons per day in 1985. Industrial waste rose from 13,130 to 33,349 tons per day in 1985. Respiratory diseases are precipitated by exposure to sulphur dioxide, which is produced during cooking and heating with coal briquets; to nitrogen dioxide from automobile exhaust; and to carbon monoxide from coal briquets. Indoor air pollution from particles such as radon, asbestos, cigarette smoke, fungus, and bacteria also impacts on health. Tolerance limits have been reached or surpassed in many cities, particularly in Seoul. Air pollution is worse during the winter. The poor are particularly affected because of the continued use of coal briquets for heating. Industry contributes to water pollution. The volume of industrial waste water quadrupled between 1980 and 1990. In Seoul, however, population size directly contributes to 64.3% of water pollution, and the remaining 35.2% is from factories. Although livestock contributes to only 0.5% of water pollution, livestock drainage contributes to 36.3% of chemical materials in polluted water. Biological oxygen demand has also exceeded tolerance limits. Water reservoirs contain toxic chemicals such as lead, copper, mercury, arsenic, phenol, phosphorus, and nitrogen, which take a longer time to affect health. The Anti-Pollution Law of 1963 and the Environmental Protection Law of 1977 were adopted, but public participation was problematic, and funding for assessment was limited. NGOs have been active in environmental programs since democratization in 1987.

Modeling vadose zone processes during land application of food-processing waste water in California's Central Valley.

PubMed

Miller, Gretchen R; Rubin, Yoram; Mayer, K Ulrich; Benito, Pascual H

2008-01-01

Land application of food-processing waste water occurs throughout California's Central Valley and may be degrading local ground water quality, primarily by increasing salinity and nitrogen levels. Natural attenuation is considered a treatment strategy for the waste, which often contains elevated levels of easily degradable organic carbon. Several key biogeochemical processes in the vadose zone alter the characteristics of the waste water before it reaches the ground water table, including microbial degradation, crop nutrient uptake, mineral precipitation, and ion exchange. This study used a process-based, multi-component reactive flow and transport model (MIN3P) to numerically simulate waste water migration in the vadose zone and to estimate its attenuation capacity. To address the high variability in site conditions and waste-stream characteristics, four food-processing industries were coupled with three site scenarios to simulate a range of land application outcomes. The simulations estimated that typically between 30 and 150% of the salt loading to the land surface reaches the ground water, resulting in dissolved solids concentrations up to sixteen times larger than the 500 mg L(-1) water quality objective. Site conditions, namely the ratio of hydraulic conductivity to the application rate, strongly influenced the amount of nitrate reaching the ground water, which ranged from zero to nine times the total loading applied. Rock-water interaction and nitrification explain salt and nitrate concentrations that exceed the levels present in the waste water. While source control remains the only method to prevent ground water degradation from saline wastes, proper site selection and waste application methods can reduce the risk of ground water degradation from nitrogen compounds.

[Purification of complicated industrial organic waste gas by complex absorption].

PubMed

Chen, Ding-Sheng; Cen, Chao-Ping; Tang, Zhi-Xiong; Fang, Ping; Chen, Zhi-Hang

2011-12-01

Complicated industrial organic waste gas with the characteristics of low concentration,high wind volume containing inorganic dust and oil was employed the research object by complex absorption. Complex absorption mechanism, process flow, purification equipment and engineering application were studied. Three different surfactants were prepared for the composite absorbent to purify exhaust gas loaded with toluene and butyl acetate, respectively. Results show that the low surface tension of the composite absorbent can improve the removal efficiency of toluene and butyl acetate. With the advantages of the water film, swirl plate and fill absorption device, efficient absorption equipment was developed for the treatment of complicated industrial organic waste gas. It is with superiorities of simple structure, small size, anti-jam and high mass transfer. Based on absorption technology, waste gas treatment process integrated with heating stripping, burning and anaerobic and other processes, so that emissions of waste gas and absorption solution could meet the discharge standards. The technology has been put into practice, such as manufacturing and spraying enterprises.

[Pollution Characteristics and Ecological Risk of PBDEs in Water and Sediment from an Electronic Waste Dismantling Area in Taizhou].

PubMed

Chen, Xiang-ping; Peng, Bao-qi; Lü, Su-ping; Chen, Qiang; Zhang, Yong; Huang, Chang-jiang; Dong, Qiao-xiang

2016-05-15

An e-waste dismantling industrial park of Taizhou was selected as the sampling center, within a radius of 16 km, and a total of 30 sampling sites were designed in three circles as follows: C (3 km), S (5-10 km) and R (10-16 km). Pollution characteristics and ecological risk of polybrominated diphenyl ethers (PBDEs) in water and sediments were investigated. The concentrations of PBDEs in water ranged from 9.4 to 57.2 ng · L⁻¹, with a mean value of 25.9 ng · L⁻¹; and 3.7 to 38,775 ng · g⁻¹, with an average of 2 779 ng · g⁻¹ in sediments. BDE-209 was the predominant congener. The spatial distribution patterns of PBDE levels in water and sediment were both in the following order: C > S > R. Furthermore, the concentrations of PBDEs in sediments showed significant negative correlation against the distance from the industrial park (P < 0.01). Compared with other regions around the world, the PBDEs contamination was more serious in the area, which indicated that e-waste dismantling activity was one of the significant sources for PBDEs pollution. It was estimated that a total of 30. 7 t PBDEs (including 28. 9 t BDE- 209) was discharged into surrounding environment as a result of dismantling industrial activities in last 40 years. A preliminary ecological risk assessment for PBDEs in water and sediments was conducted by hazard quotient method. The results demonstrated that the Penta-BDEs in the center of e-waste dismantling area ( a radius of 1.5 km) was at particularly high risk level and could cause serious influence on the ecological safety and human health.

The Minimization of Organic and Metallic Industrial Waste Via LEMNA MINOR Concentration

DTIC Science & Technology

1992-12-30

from municipal and industrial waste waters. Duckweed is a floating, widespread and fast-growing plant. It is smal, 3asy to cultivate and highly sensitive...and Cairns, J. Jr., "Accumulation and Depuration of Metals by Duckweed (Lemna perpusilla)," Ecotoxicology and Environmental Safety, 5, 87-96, 1981...to separate substances of different densities. calla: a plant of the arum family, native to South Africa, but cultivated in the United States, and

A Review on the Valorization of Macroalgal Wastes for Biomethane Production

PubMed Central

Barbot, Yann Nicolas; Al-Ghaili, Hashem; Benz, Roland

2016-01-01

The increased use of terrestrial crops for biofuel production and the associated environmental, social and ethical issues have led to a search for alternative biomass materials. Terrestrial crops offer excellent biogas recovery, but compete directly with food production, requiring farmland, fresh water and fertilizers. Using marine macroalgae for the production of biogas circumvents these problems. Their potential lies in their chemical composition, their global abundance and knowledge of their growth requirements and occurrence patterns. Such a biomass industry should focus on the use of residual and waste biomass to avoid competition with the biomass requirements of the seaweed food industry, which has occurred in the case of terrestrial biomass. Overabundant seaweeds represent unutilized biomass in shallow water, beach and coastal areas. These eutrophication processes damage marine ecosystems and impair local tourism; this biomass could serve as biogas feedstock material. Residues from biomass processing in the seaweed industry are also of interest. This is a rapidly growing industry with algae now used in the comestible, pharmaceutical and cosmetic sectors. The simultaneous production of combustible biomethane and disposal of undesirable biomass in a synergistic waste management system is a concept with environmental and resource-conserving advantages. PMID:27338422

A Review on the Valorization of Macroalgal Wastes for Biomethane Production.

PubMed

Barbot, Yann Nicolas; Al-Ghaili, Hashem; Benz, Roland

2016-06-21

The increased use of terrestrial crops for biofuel production and the associated environmental, social and ethical issues have led to a search for alternative biomass materials. Terrestrial crops offer excellent biogas recovery, but compete directly with food production, requiring farmland, fresh water and fertilizers. Using marine macroalgae for the production of biogas circumvents these problems. Their potential lies in their chemical composition, their global abundance and knowledge of their growth requirements and occurrence patterns. Such a biomass industry should focus on the use of residual and waste biomass to avoid competition with the biomass requirements of the seaweed food industry, which has occurred in the case of terrestrial biomass. Overabundant seaweeds represent unutilized biomass in shallow water, beach and coastal areas. These eutrophication processes damage marine ecosystems and impair local tourism; this biomass could serve as biogas feedstock material. Residues from biomass processing in the seaweed industry are also of interest. This is a rapidly growing industry with algae now used in the comestible, pharmaceutical and cosmetic sectors. The simultaneous production of combustible biomethane and disposal of undesirable biomass in a synergistic waste management system is a concept with environmental and resource-conserving advantages.

Installation Restoration Program. Phase 1 - Records Search, Elmendorf AFB, Alaska

DTIC Science & Technology

1983-09-01

Installation Restoration Hazardous Waste Management Past Solid Waste Disposal Sites Ground Water Contamination 26. ABSTRACT (CO- ffew. - reev. ilde It necessar...Activity Review 4-1 Industrial Operations (Shops) 4-2 Fire Training 4-13 Fuels Management 4-15 Description of Past On-sane Disposal Methods 4-23 Waste...characteristics, potential for contaminant migration and waste management practices. The details of the rating procedure are presented in Appendix H and the

Assessment of heavy metals in the industrial effluents, tube-wells and municipal supplied water of Dehradun, India.

PubMed

Kulshrestha, Shail; Awasthi, Alok; Dabral, S K

2013-07-01

The bio-geochemical cycles of metals involve the lands, rivers, oceans and the atmosphere. Although a large number of metals are introduced to the water bodies during their mining and extraction processes and geochemical weathering of rocks, but the role of domestic and industrial wastes is predominant and of much concern. Increased industrial activities has increased the incidence of percolation of toxic metal ions to the soil and water bodies and presently their presence in ecosystem, have reached to an alarming level that environmentalists are finding it difficult to enforce control measures. Human activities and large number of small and big industrial units are increasingly discharging deleterious metals present in the effluents and wastes, to the environment and aquatic systems and have contaminated heavily even the ground water. The toxic metals have a great tendency of bioaccumulation through which they enter the food chain system and ultimately affect adversely the life on this planet Earth in various ways. Further, due to contamination of irrigation system by the harmful Chemicals and toxic metals, the farm products, vegetables, fruits, potable water and even milk is not spared. This paper describes the assessment of the heavy metal concentration in various industrial effluents of the surrounding area. Various physico-chemical characteristics of the effluents collected from various sites are also reported. To assess the status of ground water quality, water samples from four tube wells of different localities of the area and four drinking water samples supplied by Municipal Distribution System were also analyzed.

Chemical and Biological Investigation of Olive Mill Waste Water - OMWW Secoiridoid Lactones.

PubMed

Vougogiannopoulou, Konstantina; Angelopoulou, Maria T; Pratsinis, Harris; Grougnet, Raphaël; Halabalaki, Maria; Kletsas, Dimitris; Deguin, Brigitte; Skaltsounis, Leandros A

2015-08-01

Olive mill waste water is the major byproduct of the olive oil industry containing a range of compounds related to Olea europaea and olive oil constituents. Olive mill waste water comprises an important environmental problem in olive oil producing countries, but it is also a valuable material for the isolation of high added value compounds. In this study, an attempt to investigate the secoiridoid content of olive mill waste water is described with the aid of ultrahigh-performance liquid chromatography-electrospray ionization (±)-high-resolution mass spectrometry and centrifugal partition chromatography methods. In total, seven secoiridoid lactones were isolated, four of which are new natural products. This is the first time that a conjugate of hydroxytyrosol and a secoiridoid lactone has been isolated from olive mill waste water and structurally characterized. Furthermore, the range of isolated compounds allowed for the proposal of a hypothesis for the biotransformation of olive secoiridoids during the production of olive mill waste water. Finally, the ability of the representative compounds to reduce the intracellular reactive oxygen species was assessed with the dichlorofluorescein assay in conjunction with the known antioxidant agent hydroxytyrosol. Georg Thieme Verlag KG Stuttgart · New York.

SMALL DRINKING WATER SYSTEMS: STATE OF THE INDUSTRY AND TREATMENT TECHNOLOGIES TO MEET THE SAFE DRINKING WATER ACT REQUIREMENTS

EPA Science Inventory

This report reviews current national data for small drinking water treatment systems, regulations pertaining to small systems, current treatment technologies, disposal of wastes, source water protection, security, and monitoring. The document serves as a roadmap for future small...

Characterization of industrial waste from a natural gas distribution company and management strategies: a case study of the East Azerbaijan Gas Company (Iran).

PubMed

Taghipour, Hassan; Aslhashemi, Ahmad; Assadi, Mohammad; Khodaei, Firoz; Mardangahi, Baharak; Mosaferi, Mohammad; Roshani, Babak

2012-10-01

Although a fundamental prerequisite for the successful implementation of any waste management plan is the availability of sufficient and accurate data, there are few available studies regarding the characterization and management of gas distribution company waste (GDCW). This study aimed to characterize the industrial waste generated by the East Azerbaijan Gas Distribution Company (EAGDC) and to present environmental management strategies. The EAGDC serves 57 cities and 821 villages with a total population of more than 2.5 million as well as numerous industrial units. The methodology of this study was based on a checklist of data collected from each zone of the company, site visits (observation), and quantity and quality analysis according to the formal data available from different zones. The results indicate that more than 35 different kinds of industrial solid waste are generated in different industrial installations. The most important types of generated waste include empty barrels (including mercaptans, diesel fuel, deionized waters and oil), faulty gas meters and regulators, a variety of industrial oils, sleeves, filter elements and faulty pipes, valves and fittings. The results indicated that, currently, GDCW is generally handled and disposed of with domestic waste, deposited in companies' installation yards and stores or, sometimes, recycled through non-scientific approaches that can create health risks to the public and the environment, even though most of the GDCW was determined to be recyclable or reusable materials. This study concludes that gas distribution companies must pay more attention to source reduction, recycling and reusing of waste to preserve natural resources, landfill space and the environment.

40 CFR 261.3 - Definition of hazardous waste.

Code of Federal Regulations, 2014 CFR

2014-07-01

... discharged to the refinery oil recovery sewer before primary oil/water/solids separation—heat exchanger bundle cleaning sludge from the petroleum refining industry (EPA Hazardous Waste No. K050), crude oil... oil tank sediment and/or in-line filter/separation solids from petroleum refining operations (EPA...

40 CFR 261.3 - Definition of hazardous waste.

Code of Federal Regulations, 2012 CFR

2012-07-01

... discharged to the refinery oil recovery sewer before primary oil/water/solids separation—heat exchanger bundle cleaning sludge from the petroleum refining industry (EPA Hazardous Waste No. K050), crude oil... oil tank sediment and/or in-line filter/separation solids from petroleum refining operations (EPA...

40 CFR 261.3 - Definition of hazardous waste.

Code of Federal Regulations, 2013 CFR

2013-07-01

... discharged to the refinery oil recovery sewer before primary oil/water/solids separation—heat exchanger bundle cleaning sludge from the petroleum refining industry (EPA Hazardous Waste No. K050), crude oil... oil tank sediment and/or in-line filter/separation solids from petroleum refining operations (EPA...

Recent Trends in Sustainable Textile Waste Recycling Methods: Current Situation and Future Prospects.

PubMed

Pensupa, Nattha; Leu, Shao-Yuan; Hu, Yunzi; Du, Chenyu; Liu, Hao; Jing, Houde; Wang, Huaimin; Lin, Carol Sze Ki

2017-08-16

In recent years, there have been increasing concerns in the disposal of textile waste around the globe. The growth of textile markets not only depends on population growth but also depends on economic and fashion cycles. The fast fashion cycle in the textile industry has led to a high level of consumption and waste generation. This can cause a negative environmental impact since the textile and clothing industry is one of the most polluting industries. Textile manufacturing is a chemical-intensive process and requires a high volume of water throughout its operations. Wastewater and fiber wastes are the major wastes generated during the textile production process. On the other hand, the fiber waste was mainly created from unwanted clothes in the textile supply chain. This fiber waste includes natural fiber, synthetic fiber, and natural/synthetic blends. The natural fiber is mostly comprised of cellulosic material, which can be used as a resource for producing bio-based products. The main challenge for utilization of textile waste is finding the method that is able to recover sugars as monosaccharides. This review provides an overview of valorization of textile waste to value-added products, as well as an overview of different strategies for sugar recovery from cellulosic fiber and their hindrances.

A Review on overboard CEOR discharged produced water treatment and remediation

NASA Astrophysics Data System (ADS)

Rawindran, H.; Krishnan, S.; Sinnathambi, C. M.

2017-06-01

Produced water is a waste by-product generated during oil and gas recovery operations. It contains the mixture of organic and inorganic compounds. Produced water management is a challenge faced by the petroleum practitioners worldwide. Build-up of chemical wastes from produced water causes huge footprint, which results in high CapEx and OpEx. Different technologies are practiced by various practitioners to treat the produced waste water. However, the constituents removed by each technology and the degree of organic compound removal has to be considered to identify the potential and effective treatment technologies for offshore industrial applications. Current produced water technologies and their successful applications have advantages and disadvantages and can be ranked on the basis of several factors, such as their discharge limit into water bodies, reinjection in producing well, or for any miscellaneous beneficial use. This paper attempts to provide a review of existing physical and chemical treatment technologies used for management of produced water. Based on our analysis, suitable methods will be recommended for offshore waste water treatment technologies.

Tracing Waste Water with Li isotopes

NASA Astrophysics Data System (ADS)

Millot, R.; Desaulty, A. M.

2015-12-01

The contribution of human activities such as industries, agriculture and various domestic inputs, becomes more and more significant in the chemical composition of the dissolved load of rivers. Human factors act as a supplementary key process. Therefore the mass-balance for the budget of catchments and river basins include anthropogenic disturbances. In the present study, we investigate waste water tracing by the use of Li isotopes in a small river basin near Orléans in France (l'Egoutier, 15 km² and 5 km long). It is well known that Li has strategic importance for numerous industrial applications including its use in the production of batteries for both mobile devices (computers, tablets, smartphones, etc.) and electric vehicles, but also in pharmaceutical formulations. In the present work, we collected river waters samples before and after the release from a waste water treatment plant connected to an hospital. Lithium isotopic compositions are rather homogeneous in river waters with δ7Li values around -0.5‰ ± 1 along the main course of the stream (n=7). The waste water sample is very different from the natural background of the river basin with Li concentration being twice of the values without pollution and significant heavy lithium contribution (δ7Li = +4‰). These preliminary results will be discussed in relation with factors controlling the distribution of Li and its isotopes in this specific system and compared with the release of other metals such as Pb or Zn.

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

40 CFR 146.5 - Classification of injection wells.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., an underground source of drinking water. (2) Other industrial and municipal disposal wells which... underground source of drinking water. (3) Radioactive waste disposal wells which inject fluids below the lowermost formation containing an underground source of drinking water within one quarter mile of the well...

Assessing chemical exposure and ecological impacts of environmental surface waters using cell culture-based metabolomic

EPA Science Inventory

Waste water treatment plants (WWTPs), as well as industrial and agricultural operations release complex mixtures of anthropogenic chemicals that negatively affect surface water quality. Previous studies have shown that exposure to such complex chemical mixtures can produce adver...

Toward zero waste to landfill: an effective method for recycling zeolite waste from refinery industry

NASA Astrophysics Data System (ADS)

Homchuen, K.; Anuwattana, R.; Limphitakphong, N.; Chavalparit, O.

2017-07-01

One-third of landfill waste of refinery plant in Thailand was spent chloride zeolite, which wastes a huge of land, cost and time for handling. Toward zero waste to landfill, this study was aimed at determining an effective method for recycling zeolite waste by comparing the chemical process with the electrochemical process. To investigate the optimum conditions of both processes, concentration of chemical solution and reaction time were carried out for the former, while the latter varied in term of current density, initial pH of water, and reaction time. The results stated that regenerating zeolite waste from refinery industry in Thailand should be done through the chemical process with alkaline solution because it provided the best chloride adsorption efficiency with cost the least. A successful recycling will be beneficial not only in reducing the amount of landfill waste but also in reducing material and disposal costs and consumption of natural resources as well.

Combined Heat and Power

EPA Pesticide Factsheets

CHP is on-site electricity generation that captures the heat that would otherwise be wasted to provide useful thermal energy such as steam or hot water than can be used for space heating, cooling, domestic hot water and industrial processes.

US UKRAINE ENVIRONMENTAL CAPACITY BUILDING PROJECT

EPA Science Inventory

Ukraine, when part of the former Soviet Union, was responsible for about 25% of its overall industrial production. This aging industrial infrastructure continues to emit enormous volumes of air and water pollution and wastes. Ukraine, according to UNDP, is ranked 11th in the wo...

40 CFR 63.1595 - List of definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... a POTW that accepts a waste stream regulated by an industrial NESHAP and provides treatment and...-containing waste stream to the POTW for treatment to comply with 40 CFR part 61, Subpart FF—National Emission... receive grant assistance under the Subchapter II of the Clean Water Act, and any federally owned treatment...

Study of Polyolefines Waste Thermo-Destruction in Large Laboratory and in Industrial Installations

DTIC Science & Technology

2014-12-15

coke ”–waste after thermo-destruction carried out on the module No 2 showed an content to 46.1% of ash [20]. This ash content indicates a very large... coke (post-production waste) from the wastes thermo-destruction on 2 modules of vertical modular installation for thermo-destruction of used polymer...of receivedwaste water, the quantity of received coke , the quantity of gaseous product in periods of carrying out installation work before (first

Using Waste Heat for External Processes (English/Chinese) (Fact Sheet) (in Chin3se; English)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Chinese translation of the Using Waste Heat for External Processes fact sheet. Provides suggestions on how to use waste heat in industrial applications. The temperature of exhaust gases from fuel-fired industrial processes depends mainly on the process temperature and the waste heat recovery method. Figure 1 shows the heat lost in exhaust gases at various exhaust gas temperatures and percentages of excess air. Energy from gases exhausted from higher temperature processes (primary processes) can be recovered and used for lower temperature processes (secondary processes). One example is to generate steam using waste heat boilers for the fluid heaters used inmore » petroleum crude processing. In addition, many companies install heat exchangers on the exhaust stacks of furnaces and ovens to produce hot water or to generate hot air for space heating.« less

Contamination of water due to major industries and open refuse dumping in the steel city of Orissa--a case study.

PubMed

Mishra, P C; Behera, P C; Patel, R K

2005-04-01

Contamination of ground water is common in the areas surrounded by industrial refuse dumping sites and the probability of contamination is more where dumping is done in low lying areas and the rate of percolation through the soil is high. In order to assess the ground water pollution by leachate around the refuse dumping site, eighteen wells were selected for study. Few wells are nearer to the dumps, few are far away and others are in between. Also an attempt has been made to evaluate the effect of industrial effluents on the ground and surface water due to Integrated Rourkela Steel Plant and other major industries. From the analytical data of physico-chemical parameters, it is indicated that the river water is contaminated mainly due to the industrial and municipal effluents and the ground water of some of the analyzed areas is contaminated due to municipal and industrial solid waste dumping.

Use of textile waste water along with liquid NPK fertilizer for production of wheat on saline sodic soils.

PubMed

Yaseen, Muhammad; Aziz, Muhammad Zahir; Jafar, Abdul Aleem; Naveed, Muhammad; Saleem, Muhammad

2016-01-01

A field experiment in collaboration with a private textile industry (Noor Fatima Fabrics Private (Ltd.), Faisalabad) was conducted to evaluate the effect of disposed water from bleaching unit, printing unit and end drain for improving growth and yield of wheat under saline sodic soil. Textile waste water along with canal water (control) was applied with and without liquid NPK fertilizer. The application of liquid NPK fertilizer with end drain waste water increased plant height, spike length, flag leaf length, root length, number of tillers (m(-2)), number of fertile tillers (m(-2)), 1000 grain weight, grain yield, straw yield and biological yield up to 21, 20, 20, 44, 17, 20, 14, 44, 40 and 41%, respectively compared to canal water (control). Similarly, the NPK uptake in grain was increased up to 15, 30 and 28%, respectively by liquid fertilizer treated end drain water as compare to canal water with liquid fertilizer. Moreover, concentration of different heavy metals particularly Cu, Cr, Pb and Cd was decreased in grains by application of waste water along with liquid NPK. The result may imply that waste water application along with liquid-NPK could be a novel approach for improving growth and yield of wheat in saline sodic soils.

SIMULTANEOUS WATER CONSERVATION/RECYCLING/REUSE AND WASTE REDUCTION IN SEMICONDUCTOR MANUFACTURING

EPA Science Inventory

The project was devoted to two separate arms of research.  The overall goals of this research was to reduce the water use in the semi-conductor industry through a comprehensive program to reduce water usage in manufacturing processes, to investigate opportunitie...

Influence of anionic surface-active agents on the uptake of heavy metals by water hyacinth (Eichhornia crassipes)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muramoto, S.; Oki, Y.

1984-10-01

In a previous paper, the ability of water hyacinth to remove toxic heavy metals, cadmium, lead, and mercury, from a metal-containing solution was reported. However, information on the effects of surface-active agents on the metal uptake from waste water by water hyacinth is insufficient. Surface-active agents including anionic detergents have been found in lake, ponds, and rivers polluted by waste from industry and municipal sewage treatment plants. The present study examines the uptake of cadmium or nickel in the presence of the anionic detergent sodium dedecyl sulfate.

CONTAMINATION OF PUBLIC GROUND WATER SUPPLIES BY SUPERFUND SITES

EPA Science Inventory

Multiple sources of contamination can affect ground water supplies, including municipal landfills, industrial operations, leaking underground storage tanks, septic tank systems, and prioritized uncontrolled hazardous waste sites known as “Superfund” sites. A review of Superfund R...

Treatment of batik waste using distillation method

NASA Astrophysics Data System (ADS)

Riyanto, Sidiq, Nurma Yunita; Hidayah, Nailil

2017-12-01

In this study has been the treatment of batik waste using distillation method. This study aims to the treatment of batik waste using distillation method. Batik is a world heritage that has an impact on economic improvement and environmental damage. Batik waste is a hazardous and toxic waste material. Batik waste in this research has been taken from Batik Industry in Yogyakarta, Indonesia. Batik waste of 5 L is included in the distillation apparatus, then the distillation run for 4 hours. The distillation product of solids and liquids is collected and analyzed. The solid produced at the distillation boiler was analyzed by FTIR. The distillation liquid was analyzed ammonia and COD concentration using UV-Vis Spectrophotometer. The result of the analysis showed that based on FTIR spectra obtained by dye with high purity. The analysis results shown are of ammonia, COD and pH were 0.652 mg/L, 238.31 mg/L, and 7.306, respectively. The compounds produced by boiler are the azo dye based on the spectrum at wave numbers 1554.07 cm-1. The conclusion of this research is that the distillation method is very suitable for the treatment of the batik waste at small batik industry. Advantages of distillation techniques that can be obtained two products are water and dye that can be used in batik industry.

Treatment of the Bleaching Effluent from Sulfite Pulp Production by Ceramic Membrane Filtration

PubMed Central

Ebrahimi, Mehrdad; Busse, Nadine; Kerker, Steffen; Schmitz, Oliver; Hilpert, Markus; Czermak, Peter

2015-01-01

Pulp and paper waste water is one of the major sources of industrial water pollution. This study tested the suitability of ceramic tubular membrane technology as an alternative to conventional waste water treatment in the pulp and paper industry. In this context, in series batch and semi-batch membrane processes comprising microfiltration, ultrafiltration and nanofiltration, ceramic membranes were developed to reduce the chemical oxygen demand (COD) and remove residual lignin from the effluent flow during sulfite pulp production. A comparison of the ceramic membranes in terms of separation efficiency and performance revealed that the two-stage process configuration with microfiltration followed by ultrafiltration was most suitable for the efficient treatment of the alkaline bleaching effluent tested herein, reducing the COD concentration and residual lignin levels by more than 35% and 70%, respectively. PMID:26729180

Treatment of the Bleaching Effluent from Sulfite Pulp Production by Ceramic Membrane Filtration.

PubMed

Ebrahimi, Mehrdad; Busse, Nadine; Kerker, Steffen; Schmitz, Oliver; Hilpert, Markus; Czermak, Peter

2015-12-31

Pulp and paper waste water is one of the major sources of industrial water pollution. This study tested the suitability of ceramic tubular membrane technology as an alternative to conventional waste water treatment in the pulp and paper industry. In this context, in series batch and semi-batch membrane processes comprising microfiltration, ultrafiltration and nanofiltration, ceramic membranes were developed to reduce the chemical oxygen demand (COD) and remove residual lignin from the effluent flow during sulfite pulp production. A comparison of the ceramic membranes in terms of separation efficiency and performance revealed that the two-stage process configuration with microfiltration followed by ultrafiltration was most suitable for the efficient treatment of the alkaline bleaching effluent tested herein, reducing the COD concentration and residual lignin levels by more than 35% and 70%, respectively.

To study the recovery of L-Cysteine using halloysite nanotubes after heavy metal removal

NASA Astrophysics Data System (ADS)

Thakur, Juhi

2016-04-01

Industrial wastes are a major source of soil and water pollution that originate from mining industries, chemical industries, metal processing industries, etc. These wastes consist of a variety of chemicals including phenolics, heavy metals, etc. Use of industrial effluent and sewage sludge on agricultural land has become a common practice in the world which results in these toxic metals being transferred and ultimately concentrate in plant tissues from water and the soil. The metals that get accumulated, prove detrimental to plants themselves and may also cause damage to the healths of animals as well as man. This is because the heavy metals become toxins above certain concentrations, over a narrow range. As a further matter, these metals negatively affect the natural microbial populations as well, that leads to the disruption of fundamental ecological processes. However, many techniques and methods have been advanced to clear the heavy metal polluted soils and waters. One important method is by removing heavy metals with the help of amino acids like L-Cysteine and L-Penicillamine. But also, economy of removal of pollutant heavy metals from soils and waters is a major concern. Present study helps in decreasing the cost for large-scale removal of heavy metals from polluted water by recovering the amino acid (L-Cysteine) after removal of nickel (Ni+2) at a fixed pH, by binding the Ni+2 with halloysite nanotubes(HNT), so that L-Cysteine can be reused again for removal of heavy metals.

Mine waste management legislation. Gold mining areas in Romania

NASA Astrophysics Data System (ADS)

Maftei, Raluca-Mihaela; Filipciuc, Constantina; Tudor, Elena

2014-05-01

Problems in the post-mining regions of Eastern Europe range from degraded land and landscapes, huge insecure dumps, surface cracks, soil pollution, lowering groundwater table, deforestation, and damaged cultural potentials to socio economic problems like unemployment or population decline. There is no common prescription for tackling the development of post-mining regions after mine closure nor is there a common definition of good practices or policy in this field. Key words : waste management, legislation, EU Directive, post mining Rosia Montana is a common oh 16 villages; one of them is also called Rosia Montana, a traditional mining Community, located in the Apuseni Mountains in the North-Western Romania. Beneath part of the village area lays one of the largest gold and silver deposits in Europe. In the Rosia Montana area mining had begun ever since the height of the Roman Empire. While the modern approach to mining demands careful remediation of environmental impacts, historically disused mines in this region have been abandoned, leaving widespread environmental damage. General legislative framework Strict regulations and procedures govern modern mining activity, including mitigation of all environmental impacts. Precious metals exploitation is put under GO no. 190/2000 re-published in 2004. The institutional framework was established and organized based on specific regulations, being represented by the following bodies: • The Ministry of Economy and Commerce (MEC), a public institution which develops the Government policy in the mining area, also provides the management of the public property in the mineral resources area; • The National Agency for the development and implementation of the mining Regions Reconstruction Programs (NAD), responsible with promotion of social mitigation measures and actions; • The Office for Industry Privatization, within the Education Ministry, responsible with privatization of companies under the CEM; • The National Agency for Mineral Resources (NAMR) manages, on behalf of the state, the mineral resources. Waste management framework Nowadays, Romania, is trying to align its regulation concerning mining activity to the European legislation taking into consideration waste management and their impact on the environment. Therefore the European Waste Catalog (Commission Decision 2001/118/EC) has been updated and published in the form of HG 856/2002 Waste management inventory and approved wastes list, including dangerous wastes. The HG 349/2005 establishes the legal framework for waste storage activity as well as for the monitoring of the closing and post-closing existing deposits, taking into account the environment protection and the health of the general population. Based on Directive 2000/60/EC the Ministry of Waters Administration, Forests and Environment Protection from Romania issued the GO No 756/1997 (amended by GO 532/2002 and GO 1144/2002),"Regulations for environment pollution assessment" that contains alarm and intervention rates for soil pollution for contaminants such as metals, metalloids (Sb, Ag, As, Be, Bi, B, Cd, Co, Cr, Cu, Hg, Mo, Ni, Pb, Se, Sn, TI, V, Zn) and cyanides. Also GO No 756/1997 was amended and updated by Law No 310/2004 and 112/2006 in witch technical instructions concerning general framework for the use of water sources in the human activities including mining industry, are approved. Chemical compounds contained in industrial waters are fully regulated by H. G. 352/2005 concerning the contents of waste water discharged. Directive 2006/21/EC of the European Parliament and of the Council relating to the management of waste from extractive industries and amending Directive 2004/35/EC is transposed into the national law of the Romanian Government under Decision No 856/2008. The 856/2008 Decision on the management of waste from extractive industries establishes "the legal framework concerning the guidelines, measures and procedures to prevent or reduce as far as possible any adverse effects on the environment, in particular water, air, soil, fauna, flora and landscape, and any health risks to the population, arising as a result of waste management in extractive industries". Based on the Commission decision 2009/339/EC concerning the waste management facilities - classification criteria - Romanian Government issued GO 2042/2010 witch states the procedures for approving the plan of waste management in extractive industries and its applications norms. Law No. 22/2001 fallows the regulations from the Espoo Convention on assessing the impact of mining on the environment sector in a cross-border context. This work is presented within the framework of SUSMIN project.

Decision Document for the Storm Water Outfalls/Industrial Wastewater Treatment Plant, Pesticide Rinse Area, Old Fire Fighting Training Pit, Illicit PCB Dump Site, and the Battery Acid Pit Fort Lewis, Washington

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cantrell, Kirk J; Liikala, Terry L; Strenge, Dennis L

PNNL conducted independent site evaluations for four sites at Fort Lewis, Washington, to determine their suitability for closure on behalf of the installation. These sites were recommended for ''No Further Action'' by previous investigators and included the Storm Water Outfalls/Industrial Waste Water Treatment Plant (IWTP), the Pesticide Rinse Area, the Old Fire Fighting Training Pit, and the Illicit PCB Dump Site.

Decision Document for the Storm Water Outfalls/Industrial Wastewater Treatment Plant, Pesticide Rinse Area, Old Fire Fighting Training Pit, Illicit PCB Dump Site, and the Battery Acid Pit Fort Lewis, Washington

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cantrell, Kirk J.; Liikala, Terry L.; Strenge, Dennis L.

PNNL conducted independent site evaluations for four sites at Fort Lewis, Washington, to determine their suitability for closure on behalf of the installation. These sites were recommended for "No Further Action" by previous invesitgators and included the Storm Water Outfalls/Industrial Waste Water Treatment Plant (IWTP), the Pesticide Rinse Area, the Old Fire Fighting Training Pit, and the Illicit PCB Dump Site.

DEVELOPMENT OF HOST-SPECIFIC METAGENOMIC MARKERS FOR MICROBIAL SOURCE TRACKING USING A NOVEL METAGENOMIC APPROACH

EPA Science Inventory

Fecal contamination of source waters is an important issue to the drinking water industry. Improper disposal of animal waste, leaky septic tanks, storm runoff, and wildlife can all be responsible for spreading enteric pathogens into source waters. As a result, methods that can pi...

Long-term Trends in St. Louis River Water Quality

EPA Science Inventory

Water quality impairments caused by sewage and industrial waste discharge into the St. Louis River have been a primary concern for clean-up efforts throughout the last century. Surveys dating back to 1928 reveal severely degraded water quality in much of the river below Fond du L...

Adsorbent material based on passion-fruit wastes to remove lead (Pb), chromium (Cr) and copper (Cu) from metal-contaminated waters

NASA Astrophysics Data System (ADS)

Campos-Flores, Gaby; Castillo-Herrera, Alberto; Gurreonero-Fernández, Julio; Obeso-Obando, Aída; Díaz-Silva, Valeria; Vejarano, Ricardo

2018-04-01

The aim of the present work was to evaluate the feasibility of passion-fruit shell (PFS) biomass as adsorbent material to remove heavy metals from contaminated waters. Model mediums were used, which were composed of distilled water and the respective metal: lead (Pb), chromium (Cr) and copper (Cu), with a dose of 10g of dry PFSbiomass per liter of medium. The residual concentration of each metal was determined by Atomic Absorption Spectrophotometry (AAS). A good adsorption capacity was exhibited by this agro industrial waste, achieving removal levels of 96,93 and 82% for Pb, Cr and Cu, respectively. In addition, the results obtained showed an adequate fit to the Freundlich model (R2 > 0.91), on the basis of which, the following values of adsorption capacity (k: 1.7057, 0.6784, 0.3302) and adsorption intensity (n: 0.6869, 2.3474, 1.0499), for Pb, Cr and Cu respectively, were obtained. Our results suggest that Pb, Cr and Cu ions can be removed by more than 80% by using this agro industrial waste, which with a minimum treatment could be used as an adsorbent material in the treatment of metal-contaminated waters.

Bioenergy Potential Based on Vinasse From Ethanol Industrial Waste to Green Energy Sustainability

NASA Astrophysics Data System (ADS)

Harihastuti, Nani; Marlena, Bekti

2018-02-01

The waste water from alcohol industry is called vinasse has a high organic content, with BOD5 = 109.038 mg / l, COD = 353.797 mg / l and TSS = 7200 mg / l, pH 4-5 with a temperature of around 40-50ºC. The current treatment of alcohol waste water, most still using facultative anaerobic technology with open ponds that are only covered with HDPE plastics. This technology produces less optimal biogas and has a weakness that is the hydraulic residence time (HRT) for long (40-50 days), wide land needs, low COD reduction efficiency as well as high risk of fire and leakage of biogas release high to trigger the occurrence of greenhouse gas and global warming effects. Development of technology with innovation reactor integration model Fixed Dome-Hybrid Anaerobic Filter aims to expand the contact area between the substrate and microbial with modification of the substrate flow system and the area of the filter and integrate with the gas accumulator. The design of this Fixed Dome-Hybrid Anaerobic filter integration model technology, has the advantage of producing optimal bioenergy with CH4 more than 50% content with decrease of COD more than 85% and hydraulic residence time of about 10 (ten) days, bioenergy result is renewable energy made from raw material vinasse from alcohol industrial waste which can be utilized for fuel substitution on the distillation process or boiler process of the industry in a sustainable and cleaner environment.

Interaction of potato production systems and the environment: a case of waste water irrigation in central Washington.

PubMed

Wang, H Holly; Tan, Tih Koon; Schotzko, R Thomas

2007-02-01

Potato production and processing are very important activities in the agricultural economy of the Pacific Northwest. Part of the reason for the development of this industry has been the availability of water for both growing and processing. A great amount of water is used in processing potato products, such as frozen French fries, and the waste water is a pollutant because it contains high levels of nitrate and other nutrients. Using this waste water to irrigate the fields can be a suitable disposal method. Field application will reduce potato fertilizer costs, but it can also cause underground water contamination if over-applied to the field. In this econometric study, we used field data associated with current waste water applications in central Washington to examine the yield response as well as the soil nitrogen content response to waste water applications. Our results from the production model show that both water and nitrogen positively affect crop yields at the current levels of application, but potassium has been over applied. This implies that replacing some waste water with fresh water and nitrogen fertilizer will increase production. The environmental model results show that applying more nitrogen to the soil leads to more movement below the root zone. The results also suggest that higher crop yields lead to less nitrogen in the soil, and applying more water increases crop yields, which can reduce the nitrogen left in the soil. Therefore, relative to the current practice, waste water application rates should be reduced and supplemented with fresh water to enhance nitrogen use by plants and reduce residual nitrogen in the soil.

Production and disposal of waste materials from gas and oil extraction from the Marcellus Shale Play in Pennsylvania

USGS Publications Warehouse

Maloney, Kelly O.; Yoxtheimer, David A.

2012-01-01

The increasing world demand for energy has led to an increase in the exploration and extraction of natural gas, condensate, and oil from unconventional organic-rich shale plays. However, little is known about the quantity, transport, and disposal method of wastes produced during the extraction process. We examined the quantity of waste produced by gas extraction activities from the Marcellus Shale play in Pennsylvania for 2011. The main types of wastes included drilling cuttings and fluids from vertical and horizontal drilling and fluids generated from hydraulic fracturing [i.e., flowback and brine (formation) water]. Most reported drill cuttings (98.4%) were disposed of in landfills, and there was a high amount of interstate (49.2%) and interbasin (36.7%) transport. Drilling fluids were largely reused (70.7%), with little interstate (8.5%) and interbasin (5.8%) transport. Reported flowback water was mostly reused (89.8%) or disposed of in brine or industrial waste treatment plants (8.0%) and largely remained within Pennsylvania (interstate transport was 3.1%) with little interbasin transport (2.9%). Brine water was most often reused (55.7%), followed by disposal in injection wells (26.6%), and then disposed of in brine or industrial waste treatment plants (13.8%). Of the major types of fluid waste, brine water was most often transported to other states (28.2%) and to other basins (9.8%). In 2011, 71.5% of the reported brine water, drilling fluids, and flowback was recycled: 73.1% in the first half and 69.7% in the second half of 2011. Disposal of waste to municipal sewage treatment plants decreased nearly 100% from the first half to second half of 2011. When standardized against the total amount of gas produced, all reported wastes, except flowback sands, were less in the second half than the first half of 2011. Disposal of wastes into injection disposal wells increased 129.2% from the first half to the second half of 2011; other disposal methods decreased. Some issues with data were uncovered during the analytical process (e.g., correct geospatial location of disposal sites and the proper reporting of end use of waste) that obfuscated the analyses; correcting these issues will help future analyses.

Development of biochar and chitosan blend for heavy metals uptake from synthetic and industrial wastewater

NASA Astrophysics Data System (ADS)

Hussain, Athar; Maitra, Jaya; Khan, Kashif Ali

2017-12-01

Heavy metals are usually released into water bodies from industrial/domestic effluents such as metal plating industries, mining and tanneries. Adsorption is a fundamental process in the physiochemical treatment of wastewaters because of its low cost. Great efforts have been made to use the economically efficient and unconventional adsorbents to adsorb heavy metals from aqueous solutions, such as plant wastes and agricultural waste. Biochar mixed with chitosan after crosslinking can be casted into membranes, beads and solutions which can be effectively utilized as an adsorbent for metal ion uptake. Keeping these facts into consideration, the present study was undertaken with the objective to determine the effect of various proportions of biochar-modified chitosan membranes on the sorption characteristics of different heavy metals like Cu, Pb, As and Cd along with comparison of sorption characteristics between industrial waste water samples containing multi-metals and standard synthetic stock solution containing a particular metal. It is apparent from the results that the bioadsorbent prepared from biochar and chitosan are low-cost efficacious resource due to its easy availability. It is also eco-friendly material for making adsorbent for abstraction of heavy metals from aqueous solution. This adsorbent can be best utilized for adsorption of heavy metals.

Oil industry waste: a potential feedstock for biodiesel production.

PubMed

Abbas, Javeria; Hussain, Sabir; Iqbal, Muhammad Javid; Nadeem, Habibullah; Qasim, Muhammad; Hina, Saadia; Hafeez, Farhan

2016-08-01

The worldwide rising energy demands and the concerns about the sustainability of fossil fuels have led to the search for some low-cost renewable fuels. In this scenario, the production of biodiesel from various vegetable and animal sources has attracted worldwide attention. The present study was conducted to evaluate the production of biodiesel from the oil industry waste following base-catalysed transesterification. The transesterification reaction gave a yield of 83.7% by 6:1 methanol/oil molar ratio, at 60°C over 80 min of reaction time in the presence of NaOH. The gas chromatographic analysis of the product showed the presence of 16 fatty acid methyl esters with linoleic and oleic acid as principal components representing about 31% and 20.7% of the total methyl esters, respectively. The fourier transform infrared spectroscopy spectrum of oil industry waste and transesterified product further confirmed the formation of methyl esters. Furthermore, the fuel properties of oil industry waste methyl esters, such as kinematic viscosity, cetane number, cloud point, pour point, flash point, acid value, sulphur content, cold filter plugging point, copper strip corrosion, density, oxidative stability, higher heating values, ash content, water content, methanol content and total glycerol content, were determined and discussed in the light of ASTM D6751 and EN 14214 biodiesel standards. Overall, this study presents the production of biodiesel from the oil industry waste as an approach of recycling this waste into value-added products.

Genotoxic and mutagenic effects of polluted surface water in the midwestern region of Brazil using animal and plant bioassays

PubMed Central

Dourado, Priscila Leocádia Rosa; da Rocha, Monyque Palagano; Roveda, Liriana Mara; Raposo, Jorge Luiz; Cândido, Liliam Sílvia; Cardoso, Claudia Andréa Lima; Morales, Maria Aparecida Marin; de Oliveira, Kelly Mari Pires; Grisolia, Alexeia Barufatti

2016-01-01

Abstract This study aimed to evaluate DNA damage in animal and plant cells exposed to water from the Água Boa stream (Dourados, Mato Grosso do Sul, Brazil) by using bioassays, and to identify the chemical compounds in the water to determine the water quality in the area. Through the cytotoxicity bioassay with Allium cepa, using micronucleus test, and comet assay, using Astyanax altiparanae fish, the results indicated that biological samples were genetically altered. Micronuclei were observed in erythrocytes of A. altiparanae after exposure to water from locations close to industrial waste discharge. The highest DNA damage observed with the comet assay in fish occurred with the exposure to water from locations where the presence of metals (Cu, Pb, Cd, Ni) was high, indicating the possibility of genotoxic effects of these compounds. Thus, these results reinforce the importance of conducting genotoxicity tests for developing management plans to improve water quality, and indicate the need for waste management before domestic and industrial effluents are released into the rivers and streams. PMID:27801481

National Environmental/Energy Workforce Assessment: Business and Industry.

ERIC Educational Resources Information Center

National Field Research Center Inc., Iowa City, IA.

This report presents an indication of existing workforce levels and career potentials for environmental/energy occupations within private industry. The study concerns itself with the environmental pollution control areas of air, noise, potable water, pesticides, radiation, solid waste, wastewater, and energy. The format includes an introduction to…

State waste discharge permit application for the 200 Area Effluent Treatment Facility and the State-Approved Land Disposal Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-08-01

Application is being made for a permit pursuant to Chapter 173--216 of the Washington Administrative Code (WAC), to discharge treated waste water and cooling tower blowdown from the 200 Area Effluent Treatment Facility (ETF) to land at the State-Approved Land Disposal Site (SALDS). The ETF is located in the 200 East Area and the SALDS is located north of the 200 West Area. The ETF is an industrial waste water treatment plant that will initially receive waste water from the following two sources, both located in the 200 Area on the Hanford Site: (1) the Liquid Effluent Retention Facility (LERF)more » and (2) the 242-A Evaporator. The waste water discharged from these two facilities is process condensate (PC), a by-product of the concentration of waste from DSTs that is performed in the 242-A Evaporator. Because the ETF is designed as a flexible treatment system, other aqueous waste streams generated at the Hanford Site may be considered for treatment at the ETF. The origin of the waste currently contained in the DSTs is explained in Section 2.0. An overview of the concentration of these waste in the 242-A Evaporator is provided in Section 3.0. Section 4.0 describes the LERF, a storage facility for process condensate. Attachment A responds to Section B of the permit application and provides an overview of the processes that generated the wastes, storage of the wastes in double-shell tanks (DST), preliminary treatment in the 242-A Evaporator, and storage at the LERF. Attachment B addresses waste water treatment at the ETF (under construction) and the addition of cooling tower blowdown to the treated waste water prior to disposal at SALDS. Attachment C describes treated waste water disposal at the proposed SALDS.« less

Production of proteases from organic wastes by solid-state fermentation: downstream and zero waste strategies.

PubMed

Marín, Maria; Artola, Adriana; Sánchez, Antoni

2018-04-01

Production of enzymes through solid-state fermentation (SSF) of agro-industrial wastes reports high productivity with low investment. The extraction of the final product from the solid waste and solid disposal represent the main cost of the process. In this work, the complete downstream processes of SSF of two industrial residues for the production of proteases, soy fibre (SF) and a mixture of hair and sludge (HS), were studied in terms of activity recovery, using different extraction parameters (extracting solvent, ratio solid: solvent and extraction mode). Activity after lyophilisation was tested. Solid waste valorisation after extraction was studied using respiration techniques and biogas production tests, as part of a zero waste strategy. Results showed a maximum extraction yield of 91% for SF and 121% for HS, both in agitated mode and distilled water as extraction agent. An average activity recovery of 95 ± 6 and 94 ± 6% for SF and HS, respectively, was obtained after lyophilisation and redissolution. To reduce the cost of extraction, a ratio 1:3 w : v solid-solvent in static mode is advised for SF, and 1:2 w : v extraction ratio in agitated mode for HS, both with distilled water as extracting agent. Both composting and anaerobic digestion are suitable techniques for valorisation of the waste material.

Naturally occurring radioactive materials (NORM): a matter of wide societal implication.

PubMed

Pescatore, C; Menon, S

2000-12-01

Naturally occurring radioactive materials are ubiquitous on Earth and their radioactivity may become concentrated as a result of human activities. Numerous industries produce concentrated radioactivity in their by-products: the coal industry, petroleum extraction and processing, water treatment, etc. The present reference system of radiation protection does not provide a complete framework for the coherent management of all types of radioactively contaminated materials. Inconsistencies in waste management policy and practice can be noted across the board, and especially vis-à-vis the management of radioactive waste from the nuclear industry. This article reviews the present societal approach to manage materials that are radioactive but are often not recognised as being such, and place the management of radioactive materials from the nuclear industry in perspective.

[Wet oxidation of toxic industrial waste with oxygenated water].

PubMed

Alfieri, M; Colombo, G; Velotti, R

1991-01-01

The industrial toxic waste streams hot treatment technology with hydrogen peroxide and catalysts, developed by the research laboratories of Montefluos in Bollate, allows the abatement of many organic and bio-toxic pollutants. Some treatment examples are here reported. The examples, performed on a laboratory scale, relate to industrial waste streams with a high COD (100000-200000 mg/l) in which it was possible to obtain an abatement over the 90% of pollutants like phenols, formaldehyde, dimethylformamide and phenyl acetate. The application range of this technology is similar to that of oxygen or air wet oxidation, but it has remarkable advantages due to the lower plant, maintenance and energy costs, because the treatment is performed using much more bland conditions (atmospheric pressure and 90-100 degrees C of temperature). The aim of the bio-toxic pollutants abatement and COD reduction (70-80%) is to allow the final bio-digestion waste streams with high organic content, but too diluted to be directly incenerated at a suitable cost.

Distribution characteristics and source identification of polychlorinated dibenzo-p-dioxin and dibenzofurans, and dioxin-like polychlorinated biphenyls in the waters from River Kanzaki, running through Osaka urban area, Japan.

PubMed

Kishida, Masao

2013-03-01

This is the first to elucidate the distribution and sources of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/PCDFs), and dioxin-like polychlorinated biphenyls in the waters from Kanzaki River, which is one of the most heavily polluted rivers in Japan. The World Health Organization (WHO)-toxic equivalent quantities (TEQs) in waters from the mainstream exceeded the Japanese environmental standard (1.0 pg-TEQ/L). The PCDD/PCDFs were dominated by highly chlorinated DFs, which predominantly contributed to the WHO-TEQs, suggesting that the main causes would be the incineration-related wastes. To find the sources, the dioxin congener concentrations in water and sediment samples from its tributary small waterways were determined. Abnormally high WHO-TEQs were detected in a water (50 pg-TEQ/L) and a sediment sample (41,000 ng-TEQ/kg dry weight) near the industrial solid waste incinerators (ISWIs). The PCDD/PCDF characteristics agreed well with those of the incinerator-related wastes as seen in the mainstream. These facts indicate that the dioxin pollution in the mainstream could be largely related to the industrial wastes from the ISWIs. Here, a TEQ apportionment method was used to understand the contribution of the pyrogenic sources to the WHO-TEQs. The average contribution ratios of the pyrogenic sources to WHO-TEQs were more than 80% for river waters from the mainstream, indicating that the elevated WHO-TEQs in the mainstream had been largely caused by the ISWIs.

Properties of Concrete Paving Blocks and Hollow Tiles with Recycled Aggregate from Construction and Demolition Wastes.

PubMed

Rodríguez, Carlos; Miñano, Isabel; Aguilar, Miguel Ángel; Ortega, José Marcos; Parra, Carlos; Sánchez, Isidro

2017-11-30

In recent years there has been an increasing tendency to recycle the wastes generated by building companies in the construction industry, demolition wastes being the most important in terms of volume. The aim of this work is to study the possibility of using recycled aggregates from construction and demolition wastes in the preparation of precast non-structural concretes. To that purpose, two different percentages (15% and 30%) of natural aggregates were substituted by recycled aggregates in the manufacture of paving blocks and hollow tiles. Dosages used by the company have not been changed by the introduction of recycled aggregate. Precast elements have been tested by means of compressive and flexural strength, water absorption, density, abrasion, and slipping resistance. The results obtained show the possibility of using these wastes at an industrial scale, satisfying the requirements of the Spanish standards for these elements.

Properties of Concrete Paving Blocks and Hollow Tiles with Recycled Aggregate from Construction and Demolition Wastes

PubMed Central

Rodríguez, Carlos; Miñano, Isabel; Aguilar, Miguel Ángel; Parra, Carlos

2017-01-01

In recent years there has been an increasing tendency to recycle the wastes generated by building companies in the construction industry, demolition wastes being the most important in terms of volume. The aim of this work is to study the possibility of using recycled aggregates from construction and demolition wastes in the preparation of precast non-structural concretes. To that purpose, two different percentages (15% and 30%) of natural aggregates were substituted by recycled aggregates in the manufacture of paving blocks and hollow tiles. Dosages used by the company have not been changed by the introduction of recycled aggregate. Precast elements have been tested by means of compressive and flexural strength, water absorption, density, abrasion, and slipping resistance. The results obtained show the possibility of using these wastes at an industrial scale, satisfying the requirements of the Spanish standards for these elements. PMID:29189745

Development of the water-analysis screening tool used in the initial screening for the Pennsylvania State Water Plan update of 2008

USGS Publications Warehouse

Stuckey, Marla H.

2008-01-01

The Water Resources Planning Act, Act 220 of 2002, requires the Pennsylvania Department of Environmental Protection (PaDEP) to update the State Water Plan by 2008. As part of this update, a water-analysis screening tool (WAST) was developed by the U.S. Geological Survey, in cooperation with the PaDEP, to provide assistance to the state in the identification of critical water-planning areas. The WAST has two primary inputs: net withdrawals and the initial screening criteria. A comprehensive water-use database that includes data from registration, estimation, discharge monitoring reports, mining data, and other sources was developed as input into the WAST. Water use in the following categories was estimated using water-use factors: residential, industrial, commercial, agriculture, and golf courses. A percentage of the 7-day, 10-year low flow is used for the initial screenings using the WAST to identify potential critical water-planning areas. This quantity, or initial screening criteria, is 50 percent of the 7-day, 10-year low flow for most streams. Using a basic water-balance equation, a screening indicator is calculated that indicates the potential influences of net withdrawals on aquatic-resource uses for watersheds generally larger than 15 square miles. Points representing outlets of these watersheds are colored-coded within the WAST to show the screening criteria for each watershed.

An ammonia monitor for the water industry

NASA Technical Reports Server (NTRS)

Brokenshire, J. L.; Cumming, C. A.

1995-01-01

Following the emergence of the European Community as a unified trading and economic entity, the various member states are required to follow certain directives governing their social affairs. Many of these directives concern the quality of the air we breathe, and the water that we use for consumption or in industrial processes. In order to comply with these directives a major overhaul of the water industry in the UK was required. For example, in many coastal towns and resorts there has never been any formal sewage treatment since, traditionally, all waste was dumped at sea through outfall pipes. Because this is no longer acceptable, whole new treatment systems are required.

Regenerating using aqueous cleaners with ozone and electrolysis

NASA Technical Reports Server (NTRS)

Mcginness, Michael P.

1994-01-01

A new process converts organic oil and grease contaminates in used water based cleaners into synthetic surfactants. This permits the continued use of a cleaning solution long after it would have been dumped using previously known methods. Since the organic soils are converted from contaminates to cleaning compounds the need for frequent bath dumps is totally eliminated. When cleaning solutions used in aqueous cleaning systems are exhausted and ready for disposal, they will always contain the contaminates removed from the cleaned parts and drag-in from prior cleaning steps. Even when the cleaner is biodegradable these contaminants will frequently cause the waste cleaning solution to be a hazardous waste. Chlorinated solvents are rapidly being replaced by aqueous cleaners to avoid the new ozone-depletion product-labeling-law. Many industry standard halocarbon based solvents are being completely phased out of production, and their prices have nearly tripled. Waste disposal costs and cradle-to-grave liability are also major concerns for industry today. This new process reduces the amount of water and chemicals needed to maintain the cleaning process. The cost of waste disposal is eliminated because the water and cleaning compounds are reused. Energy savings result by eliminating the need for energy currently used to produce and deliver fresh water and chemicals as well as the energy used to treat and destroy the waste from the existing cleaning processes. This process also allows the cleaning bath to be maintained at the peak performance of a new bath resulting in decreased cycle times and decreased energy consumption needed to clean the parts. This results in a more efficient and cost effective cleaning process.

Phytoremediation: A green technology to remove environmental pollutants

USDA-ARS?s Scientific Manuscript database

Land, surface water, and ground water worldwide, are increasingly affected by contaminations from industrial, research experiments, military, and agricultural activities either due to ignorance, lack of vision, carelessness, or high cost of waste disposal and treatment. The rapid build-up of toxic p...

pH neutralization of the by-product sludge waste water generated from waste concrete recycling process using the carbon mineralization

NASA Astrophysics Data System (ADS)

Ji, Sangwoo; Shin, Hee-young; Bang, Jun Hwan; Ahn, Ji-Whan

2017-04-01

About 44 Mt/year of waste concrete is generated in South Korea. More than 95% of this waste concrete is recycled. In the process of regenerating and recycling pulmonary concrete, sludge mixed with fine powder generated during repeated pulverization process and water used for washing the surface and water used for impurity separation occurs. In this way, the solid matter contained in the sludge as a by-product is about 40% of the waste concrete that was input. Due to the cement component embedded in the concrete, the sludge supernatant is very strong alkaline (pH about 12). And it is necessary to neutralization for comply with environmental standards. In this study, carbon mineralization method was applied as a method to neutralize the pH of highly alkaline waste water to under pH 8.5, which is the water quality standard of discharged water. CO2 gas (purity 99%, flow rate 10ml/min.) was injected and reacted with the waste water (Ca concentration about 750mg/L) from which solid matter was removed. As a result of the experiment, the pH converged to about 6.5 within 50 minutes of reaction. The precipitate showed high whiteness. XRD and SEM analysis showed that it was high purity CaCO3. For the application to industry, it is needed further study using lower concentration CO2 gas (about 14%) which generated from power plant.

Ultimate disposal of scrubber wastes

NASA Technical Reports Server (NTRS)

Cohenour, B. C.

1978-01-01

Part of the initial concern with using the wet scrubbers on the hypergolic propellants was the subsequential disposal of the liquid wastes. To do this, consideration was given to all possible methods to reduce the volume of the wastes and stay within the guidelines established by the state and federal environmental protection agencies. One method that was proposed was the use of water hyacinths in disposal ponds to reduce the waste concentration in the effluent to less than EPA tolerable levels. This method was under consideration and even in use by private industry, municipal governments, and NASA for upgrading existing wastewater treatment facilities to a tertiary system. The use of water hyacinths in disposal ponds appears to be a very cost-effective method for reduction and disposal of hypergolic propellants.

Studying breaking of inverted emulsions with thermolysis purification TD600

NASA Astrophysics Data System (ADS)

Tarasova, G. I.; Shevaga, O. N.; Grachyova, E. O.

2018-03-01

Currently, emulsions are used in many branches of industry and agriculture. It explains significant attention paid to issues in production, stabilization and breaking of emulsion. Besides, producing steady emulsions is of importance in many processes; the reverse problem, that of demulsification, is important as well in oil production and treatment of oil emulsion waste water. This paper studies the breaking (demulsification) of inverted emulsions with the help of thermolysis purification TD600, produced by thermal modification of purification, a large-scale waste of the sugar industry.

Industrial Pretreatment. Instructor Guide. Working for Clean Water: An Information Program for Advisory Groups.

ERIC Educational Resources Information Center

Nesbitt, John B.; Cole, Charles A.

With proper pretreatment, industrial wastes can often be treated together with municipal wastewater. Participants in the one-hour session described in the instructor's manual will learn about pretreatment options, objectives of pretreatment, and regulations governing the development and operation of a pretreatment program. A supplementary…

Estimated use of water in the United States - 1950

USGS Publications Warehouse

MacKichan, Kenneth Allen

1951-01-01

An estimated 170,000 million gallons of water was withdrawn from the ground, lakes, or streams each day on the average during 1950 and used on the farms and in the homes, factories, and business establishments of the United States. An additional 1,100,000 million gallons per day was used to generate hydro-power. Water power is the largest user of water; however, irrigation and industry also are large users of both ground and surface water. More surface water was used for industrial purposes than for irrigation, whereas more ground water was used for irrigation than for industrial purposes (fig. 1). The total withdrawal of surface water was considerably in excess of ground-water withdrawal, as shown by figure 1. Large quantities of water were used also for purposes requiring no diversion, such as navigation, waste disposal, recreation, and support of wildlife.

Minimization of organic and metallic industrial waste via lemna minor concentration. Final report, 1 September 1991-1 December 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowers-Irons, G.L.

1992-12-30

In recent years, new strict environmental laws have required improved and cost-effective water purification methods by Air Force complexes. Naturally assisted primary units (microbiological) and secondary units (macrophyte) could bring waste treatment systems into tighter compliance. Aquatic macrophytes which have rapid growth rates and absorb large quantities of nutrients could provide a practical and economic method for more complete wastewater maintenance, hazardous waste clean-up or river, lake and ground water purification. This work has shown that Lemna minor, or Common Duckweed, can successfully and thoroughly accumulate organics and metals from Air Force wastewaters.

DEVELOPMENT OF HOST-SPECIFIC METAGENOMIC MARKERS FOR MICROBIAL SOURCE TRACKING USING A NOVEL METAGENOMIC APPROACH

EPA Science Inventory

Fecal contamination of source water has always been an important issue to the drinking water industry. Improper disposal of animal waste, leaky septic tanks, storm runoff, and the abundance of wildlife in natural water systems can all be responsible for the spread of enteric path...

Electrical process in the breaking of dilute oil-in-water emulsions. Completion report, 1 July 1973-30 June 1974

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orr, C. Jr.; Keng, E.Y.H.

1974-06-01

Oils, greases, and waxes frequently occur in industrial waste waters. Simultaneously, soaps and detergents enter most waste waters from domestic and other sources. When the mixtures of waste particles in water, known as emulsions, come in contact with the soaps and detergents, they generally become quite stable. One way to break such emulsions and thereby separate out the wastes is to add chemicals that will cause the oil droplet to agglomerate into larger drops. This study sought to assess the usefulness of electrical measurements, particularly the so-called zeta potential, in guiding the treatment process to chemicals and application rates thatmore » can break measured emulsions. When the zeta potential, which for a highly stable emulsion may be as negative as -0.090 volt, is made to approach -0.015 volt, the stability of the emulsion deteriorates rapidly. Past this poin oil-in-water emulsions often break spontaneously. The larger drops will then rise to the water surface and form a distinct oil layer that can be easily removed. Laboratory applications of various chemicals to emulsion samples and subsequent zeta potential measurement should thus provide a ready guide to those trying to remove oily waste water discharge.« less

Physical, chemical, and biological aspects of subsurface organic waste injection near Wilmington, North Carolina

USGS Publications Warehouse

Leenheer, J.A.; Malcolm, R.L.; White, W.R.

1976-01-01

From May 1968 to December 1972, an industrial organic waste was injected at rates of 100 to 200 gallons per minute (6.3 to 12.6 litres per second) into a sand, gravel, and limestone aquifer of Late Cretaceous age by Hercules Inc. located near Wilmington, North Carolina. This report presents both field and laboratory data pertaining to the physical, chemical, and biological effects of waste injection into the subsurface at this particular site, a case history of the operation, predictions of the reactions between certain organic wastes and the aquifer components, and descriptions of the effects of these reactions on the subsurface movement of the wastes. The case history documents a situation in which subsurface waste injection could not be considered a successful means of waste disposal. The first injection well was used only for 1 year due to excessive wellhead pressure build-up above the specified pressure limit of 150 pounds per square inch (10.3 bars). A second injection well drilled as a replacement operated for only 5 months before it too began to have problems with plugging. Upward leakage of waste into shallower aquifers was also detected at several wells in the injection-observation well system. The multiple problems of plugging, high pressures, and waste leakage suggested that the reactive nature of the waste with the aquifer into which it was injected was the primary reason for the difficulties experienced with waste injection. A site study was initiated in June 1971 to investigate waste-aquifer interactions. The first stage of the study determined the hydrogeologic conditions at the site, and characterized the industrial waste and the native ground water found in the injection zone and other aquifers. The injection zone consisted of multiple permeable zones ranging in depth from about 850 to 1,000 feet (259 to 305 metres) below land surface. In addition to the injection zone, aquifers were found near depths of 60, 300, 500, and 700 feet (18, 91, 152, and 213 metres) below land surface. The aquifers from 300 feet (91 metres) down to the injection zone were flowing artesian with the natural pressure of the injection zone being 65 feet (20 metres) above land surface at the site. The dissolved solids concentration in the native ground water increased with depth to an average value of 20,800 mg/l (milligram per litre) (two-thirds that of seawater) in the water from the injection zone. Sodium chloride was the major dissolved solid, and all of the ground water below 300-feet (91-metres) depth was slightly alkaline. Dissolved organic carbon of the industrial waste averaged 7,100 mg/l and 95 percent of the organic carbon was identified and quantified. The major organic waste constituents in order of decreasing abundance were acetic acid, formic acid, p-toluic acid, formaldehyde, methanol, terephthalic acid, phthalic acid, and benzoic acid. Prior to injection, the waste was neutralized with lime to pH 4 so that the major inorganic waste constituent was calcium at a concentration of 1,300 mg/l. The second stage of the site study involved the observation of waste-aquifer interactions at various wells as the waste arrived and passed by the wells. Water samples obtained from three observation wells located 1,500 to 2,000 feet (457 to 607 metres) from the original injection well gave evidence for biochemical waste transformations at low waste concentrations. Gas that effervesced from these water samples contained up to 54 percent methane by volume. Ferrous iron concentrations as high as 35 mg/l, hydrogen sulfide gas, and sulfide precipitates were additional indicators of biochemical reductive processes in the subsurface environment. Approximately 3,000 organisms per millilitre were found in uncontaminated ground water from the injection zone whereas in waste-contaminated wells, the number increased to levels as high as 1,000,000 organisms per millilitre. High concentrations of waste were found to be toxic to microo

Improved waste water treatment by bio-synthesized Graphene Sand Composite.

PubMed

Poornima Parvathi, V; Umadevi, M; Bhaviya Raj, R

2015-10-01

The photocatalytic and antibacterial properties of graphene biosynthesized from sugar and anchored on sand particles has been focused here. The morphology and composition of the synthesized Graphene Sand Composite (GSC) was investigated by means of X-ray powder diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDAX), Fourier Transform Infra-red Spectroscopy (FTIR) and UV-Visible spectroscopy. SEM images show wrinkly edges. This is characteristic of graphenic morphology. Three types of waste water samples namely, textile waste (TW), sugarcane industrial waste water (SW) and domestic waste water from a local purification center at Kodaikanal (KWW) were collected and treated. Adsorption experiments showed effective removal of impurities at 0.2 g of GSC. Photocatalytic activity was analyzed under visible and ultraviolet irradiation. The rate constant for TW increased to 0.0032/min for visible light irradiation from 0.0029/min under UV irradiation. SW showed similar improved activity with rate constant as 0.0023/min in visible irradiation compared to 0.0016/min under UV irradiation. For KWW enhanced activity was seen only in visible light irradiation with rate constant 0.0025/min. GSC showed an inhibition zone of 20 mm against the bacterium Escherichia coli. Results suggest development of economic and effective waste water management systems. Copyright © 2015 Elsevier Ltd. All rights reserved.

Role of Bioadsorbents in Reducing Toxic Metals

PubMed Central

Jaishankar, Monisha; Biju, Vinai George; Krishnamurthy Nideghatta Beeregowda

2016-01-01

Industrialization and urbanization have led to the release of increasing amounts of heavy metals into the environment. Metal ion contamination of drinking water and waste water is a serious ongoing problem especially with high toxic metals such as lead and cadmium and less toxic metals such as copper and zinc. Several biological materials have attracted many researchers and scientists as they offer both cheap and effective removal of heavy metals from waste water. Therefore it is urgent to study and explore all possible sources of agrobased inexpensive adsorbents for their feasibility in the removal of heavy metals. The objective was to study inexpensive adsorbents like various agricultural wastes such as sugarcane bagasse, rice husk, oil palm shell, coconut shell, and coconut husk in eliminating heavy metals from waste water and their utilization possibilities based on our research and literature survey. It also shows the significance of developing and evaluating new potential biosorbents in the near future with higher adsorption capacity and greater reusable options. PMID:28090207

Role of Bioadsorbents in Reducing Toxic Metals.

PubMed

Mathew, Blessy Baby; Jaishankar, Monisha; Biju, Vinai George; Krishnamurthy Nideghatta Beeregowda

2016-01-01

Industrialization and urbanization have led to the release of increasing amounts of heavy metals into the environment. Metal ion contamination of drinking water and waste water is a serious ongoing problem especially with high toxic metals such as lead and cadmium and less toxic metals such as copper and zinc. Several biological materials have attracted many researchers and scientists as they offer both cheap and effective removal of heavy metals from waste water. Therefore it is urgent to study and explore all possible sources of agrobased inexpensive adsorbents for their feasibility in the removal of heavy metals. The objective was to study inexpensive adsorbents like various agricultural wastes such as sugarcane bagasse, rice husk, oil palm shell, coconut shell, and coconut husk in eliminating heavy metals from waste water and their utilization possibilities based on our research and literature survey. It also shows the significance of developing and evaluating new potential biosorbents in the near future with higher adsorption capacity and greater reusable options.

PERFORMANCE EVALUATION OF A CARBON-BASED REACTIVE BARRIER FOR NITRATE REMEDIATION

EPA Science Inventory

Nitrate (NO3-) is a common ground water contaminant related to agricultural activity, waste water disposal, leachate from landfills, septic systems, and industrial processes. This study reports on the performance of a carbon-based permeable reactive barrier (PRB) that was constr...

CARBON-BASED REACTIVE BARRIER FOR NITRATE REMEDIATION AT A FORMER SWINE CAFO

EPA Science Inventory

Nitrate (NO3-) is a common ground water contaminant related to agricultural activity, waste water disposal, leachate from landfills, septic systems, and industrial processes. This study reports on the performance of a carbon-based permeable reactive barrier (PRB) that was constr...

Quality index of the surface water of Amazonian rivers in industrial areas in Pará, Brazil.

PubMed

Medeiros, Adaelson Campelo; Faial, Kleber Raimundo Freitas; do Carmo Freitas Faial, Kelson; da Silva Lopes, Iris Danielly; de Oliveira Lima, Marcelo; Guimarães, Raphael Mendonça; Mendonça, Neyson Martins

2017-10-15

In this study was to evaluate the waters quality of the Murucupi River, located in urban agglomerate area and intense industrial activity in Barcarena City, Pará State. The Arapiranga River in Abaetetuba City was used as control area (Background), next to Barcarena. Was used the Water Quality Index (WQI) based on nine variables analized. Waters quality of the Arapiranga and Murucupi rivers were regular to good and bad to good, respectively. Anthropogenic influence on the Murucupi River was higher, mainly by the disposal of domestic effluents from the urban agglomerate and of the industrial waste tailing basins upstream of this river. Due to its less inhabited environment and further away from the area urban and industrial, the Arapiranga River was more preserved. Waters pollution of around these area is increasingly intense, and restricted its uses for various purposes. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Tea waste: an effective and economic substrate for oyster mushroom cultivation.

PubMed

Yang, Doudou; Liang, Jin; Wang, Yunsheng; Sun, Feng; Tao, Hong; Xu, Qiang; Zhang, Liang; Zhang, Zhengzhu; Ho, Chi-Tang; Wan, Xiaochun

2016-01-30

Tea waste is the residue that remains after tea leaves have been extracted by hot water to obtain water-soluble components. The waste contains a re-usable energy substrate and nutrients which may pollute the environment if they are not dealt with appropriately. Other agricultural wastes have been widely studied as substrates for cultivating mushrooms. In the present study, we cultivated oyster mushroom using tea waste as substrate. To study the feasibility of re-using it, tea waste was added to the substrate at different ratios in different experimental groups. Three mushroom strains (39, 71 and YOU) were compared and evaluated. Mycelia growth rate, yield, biological efficiency and growth duration were measured. Substrates with different tea waste ratios showed different growth and yield performance. The substrate containing 40-60% of tea waste resulted in the highest yield. Tea waste could be used as an effective and economic substrate for oyster mushroom cultivation. This study also provided a useful way of dealing with massive amounts of tea waste. © 2015 Society of Chemical Industry.

Water and wastewater in developing countries: present reality and strategy for the future.

PubMed

Ujang, Z; Buckley, C

2002-01-01

This paper summarises the paper presentation sessions at the Conference, as well giving insights on the issues related to developing countries. It also discusses the present status of practice and research on water and wastewater management, and projected future scenario based not only on the papers presented in the Conference, but also on other sources. The strategy is presented to overcome many problems in developing countries such as rapid urbanization, industrialization, population growth, financial and institutional problems and, depleting water resources. The strategy consists of Integrated Urban Water Management (IUWM), cleaner industrial production, waste minimisation and financial arrangements.

Development of a Small Thermoelectric Generators Prototype for Energy Harvesting from Low Temperature Waste Heat at Industrial Plant.

PubMed

Chiarotti, Ugo; Moroli, Valerio; Menchetti, Fernando; Piancaldini, Roberto; Bianco, Loris; Viotto, Alberto; Baracchini, Giulia; Gaspardo, Daniele; Nazzi, Fabio; Curti, Maurizio; Gabriele, Massimiliano

2017-03-01

A 39-W thermoelectric generator prototype has been realized and then installed in industrial plant for on-line trials. The prototype was developed as an energy harvesting demonstrator using low temperature cooling water waste heat as energy source. The objective of the research program is to measure the actual performances of this kind of device working with industrial water below 90 °C, as hot source, and fresh water at a temperature of about 15 °C, as cold sink. The article shows the first results of the research program. It was verified, under the tested operative conditions, that the produced electric power exceeds the energy required to pump the water from the hot source and cold sink to the thermoelectric generator unit if they are located at a distance not exceeding 50 m and the electric energy conversion efficiency is 0.33%. It was calculated that increasing the distance of the hot source and cold sink to the thermoelectric generator unit to 100 m the produced electric energy equals the energy required for water pumping, while reducing the distance of the hot source and cold sink to zero meters the developed unit produces an electric energy conversion efficiency of 0.61%.

A review of metal recovery from spent petroleum catalysts and ash.

PubMed

Akcil, Ata; Vegliò, Francesco; Ferella, Francesco; Okudan, Mediha Demet; Tuncuk, Aysenur

2015-11-01

With the increase in environmental awareness, the disposal of any form of hazardous waste has become a great concern for the industrial sector. Spent catalysts contribute to a significant amount of the solid waste generated by the petrochemical and petroleum refining industry. Hydro-cracking and hydrodesulfurization (HDS) catalysts are extensively used in the petroleum refining and petrochemical industries. The catalysts used in the refining processes lose their effectiveness over time. When the activity of catalysts decline below the acceptable level, they are usually regenerated and reused but regeneration is not possible every time. Recycling of some industrial waste containing base metals (such as V, Ni, Co, Mo) is estimated as an economical opportunity in the exploitation of these wastes. Alkali roasted catalysts can be leached in water to get the Mo and V in solution (in which temperature plays an important role during leaching). Several techniques are possible to separate the different metals, among those selective precipitation and solvent extraction are the most used. Pyrometallurgical treatment and bio-hydrometallurgical leaching were also proposed in the scientific literature but up to now they did not have any industrial application. An overview on patented and commercial processes was also presented. Copyright © 2015 Elsevier Ltd. All rights reserved.

Optimisation of industrial wastes reuse as construction materials.

PubMed

Collivignarelli, C; Sorlini, S

2001-12-01

This study concerns the reuse of two inorganic wastes, foundry residues and fly ashes from municipal solid waste incineration, as "recycled aggregate" in concrete production. This kind of reuse was optimised by waste treatment with the following steps: waste washing with water; waste stabilisation-solidification treatment with inorganic reagents; final grinding of the stabilised waste after curing for about 10-20 days. Both the treated wastes were reused in concrete production with different mix-designs. Concrete specimens were characterised by means of conventional physical-mechanical tests (compression, elasticity modulus, shrinkage) and different leaching tests. Experimental results showed that a good structural and environmental quality of "recycled concrete" is due both to a correct waste treatment and to a correct mix-design for concrete mixture.

Rubber industry

NASA Astrophysics Data System (ADS)

Staszak, Maciej

2018-03-01

Following chapter presents short introductory description of rubber and rubber industry. The main problem of rubber industry is the way of the usage of spent tires. Furthermore very important group of problems arise considering the metal and nonmetal additives which are significant component of the vulcanized rubber. The key attention is dedicated to typical ways of rubber usage in utilization and recovery of metals from spent rubber materials concentrating specifically on used tires processing. The method of recovery of rare metals from rubber tires was described. The rubber debris finds widest use in the field of waste metal solutions processing. The environmental pollution caused by metals poses serious threat to humans. Several applications of the use of waste rubber debris to remove metals from environmental waters were described. Moreover, the agriculture usage of waste tire rubber debris is described, presenting systems where the rubber material can be useful as a soil replacement.

The latent causal chain of industrial water pollution in China.

PubMed

Miao, Xin; Tang, Yanhong; Wong, Christina W Y; Zang, Hongyu

2015-01-01

The purpose of this paper is to discover the latent causal chain of industrial water pollution in China and find ways to cure the want on discharge of toxic waste from industries. It draws evidences from the past pollution incidents in China. Through further digging the back interests and relations by analyzing representative cases, extended theory about loophole derivations and causal chain effect is drawn. This theoretical breakthrough reflects deeper causality. Institutional defect instead of human error is confirmed as the deeper reason of frequent outbreaks of water pollution incidents in China. Ways for collaborative environmental governance are proposed. This paper contributes to a better understanding about the deep inducements of industrial water pollution in China, and, is meaningful for ensuring future prevention and mitigation of environmental pollution. It illuminates multiple dimensions for collaborative environmental governance to cure the stubborn problem.

The Analysis of the System of special water purification of Beloyarskaya Nuclear Power Plant unit BN-800

NASA Astrophysics Data System (ADS)

Valtseva, A. I.; Bibik, I. S.

2017-11-01

This article discusses how the latest system of special water purification KPF-30, designed specifically for the fourth power unit of Beloyarskaya nuclear power plant, which has a number of advantages over other water purification systems as chemical-physical and technical-economic, environmental, and other industrial indicators. The scheme covered in this article systems of special water purification involves the use of a hydrocyclone at the preliminary stage of water treatment, as a worthy alternative to ion-exchange filters, which can significantly reduce the volume of toxic waste. The world community implements the project of closing the nuclear fuel cycle, there is a need to improve the reliability of the equipment for safe processes and development of critical and supercritical parameters in the nuclear industry. Essentially, on operated NPP units, the only factor that can cost-effectively optimize to improve the reliability of equipment is the water chemistry. System KPF30 meets the principles and criteria of ecological safety, demonstrating the justification for reagent less method of water treatment on the main stages, in which no formation of toxic wastes, leading to irreversible consequences of environmental pollution and helps to conserve water.

Securing water for the cities.

PubMed

Satterthwaite, D

1993-01-01

Many cities in developing countries have grown so much that they can no longer provide adequate, sustainable water. Over pumping in Dakar and Mexico City has forced those cities to obtain water from ever more distant sources. In Dakar, the result has been saltwater intrusion. Overpumping has caused Mexico City to sink, in some areas by as much as 9 m, resulting in serious damage to buildings and sewage and drainage pipes. Other cities facing similar water problems are coastal cities in Peru (e.g., Lima), La Rioja and Catamarca in Argentina, cities in Northern Mexico, and cities in dry areas of Africa. For some cities, the problem is not so much ever more distant water supplies but insufficient funds to expand supplies. Bangkok and Jakarta both face saltwater intrusion into their overdrawn aquifers. Even through agriculture is the dominant user of water in most countries, demand concentrated in a small area exhausts local and regional sources and pollutes rivers, lakes, and coasts with untreated human and industrial waste. Most cities in Africa and Asia do not have a sewerage system. Further, most cities do not have the drains to deal with storm water and external floodwater, causing frequent, seasonal flooding. The resulting stagnant water provides breeding grounds for insect vectors of diseases (e.g., malaria). The problems in most cities are a result of poor management, not lack of water. Reducing leaks in existing piped distribution systems from the usual 60% loss of water to leaks to 12% would increase the available water 2-fold. Another way to address water shortages would be commercial, industrial, and recreational use of minimally treated waste water, such as is the case in Madras and Mexico City. Political solutions are needed to resolve inadequate water supply and waste management.

Ground-water protection, low-level waste, and below regulatory concern: What`s the connection?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gruhlke, J.M.; Galpin, F.L.

1991-12-31

The Environmental Protection Agency (EPA) has a responsibility to protect ground water and drinking water under a wide variety of statutes. Each statute establishes different but specific requirements for EPA and applies to diverse environmental contaminants. Radionuclides are but one of the many contaminants subject to this regulatory matrix. Low-level radioactive waste (LLW) and below regulatory concern (BRC) are but two of many activities falling into this regulatory structure. The nation`s ground water serves as a major source of drinking water, supports sensitive ecosystems, and supplies the needs of agriculture and industry. Ground water can prove enormously expensive to cleanmore » up. EPA policy for protecting ground water has evolved considerably over the last ten years. The overall goal is to prevent adverse effects to human health, both now and in the future, and to protect the integrity of the nation`s ground-water resources. The Agency uses the Maximum Contaminant Levels (MCLs) under the Safe Drinking Water Act as reference points for protection in both prevention and remediation activities. What`s the connection? Both low-level waste management and disposal activities and the implementation of below regulatory concern related to low-level waste disposal have the potential for contaminating ground water. EPA is proposing to use the MCLs as reference points for low-level waste disposal and BRC disposal in order to define limits to the environmental contamination of ground water that is, or may be, used for drinking water.« less

Profile Change When Industry Moves Into an Area. Working Paper RID 73.7.

ERIC Educational Resources Information Center

Scott, John T., Jr.

The effects of industrialization on the economic and social profile of a rural community are described in this paper. Some of the major changes when industry moves into a community are in the land use and support systems such as an increase in the demand for water, energy, and waste disposal. Other changes are in the labor force, retail sales and…

Functional and environmental assessment of the urboecosystems designed in the biologically reclamated landfill with industrial wastes (in Ryazan city)

NASA Astrophysics Data System (ADS)

Karyakin, Alexey; Vasenev, Ivan; Karyakina, Svetlana

2015-04-01

Regional environmental bodies' ability to understand, model and predict their soil cover environmental functions are especially important in case of landfill reclamation. The special attention has to be done to landfills with industrial wastes created earlier in frame of big city - comparatively closed to their residential areas. Dominated in Ryazan region sandy loam gray forest soils with not so high soil organic matter content and soil exchange capacity determine additional problems with landfill biological reclamation and continuous sustainable vegetation cover development. The modern environmental monitoring system has been developed in the big landfill with tanning industrial wastes from the biggest in Europe tannery to develop recommendation on the environmentally friendly reclamation technologies adapted to concrete landscape conditions and functional features of 2 m fresh soil-ground coating the landfill surface. More detailed monitoring system has to be developed to assess the regulatory environmental functions of the regenerated soil cover to minimize the reclamated landfill' negative impacts on the urban ecosystem air, surface and ground water quality. Obtained result will be useful for similar landfills with tanning industrial wastes environmental impact assessment and smart design.

Waste heat driven absorption refrigeration process and system

DOEpatents

Wilkinson, William H.

1982-01-01

Absorption cycle refrigeration processes and systems are provided which are driven by the sensible waste heat available from industrial processes and other sources. Systems are disclosed which provide a chilled water output which can be used for comfort conditioning or the like which utilize heat from sensible waste heat sources at temperatures of less than 170.degree. F. Countercurrent flow equipment is also provided to increase the efficiency of the systems and increase the utilization of available heat.

Industrial Assessment Centers - Small Manufacturers Reduce Energy & Increase Productivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Since 1976, the Industrial Assessment Centers (IACs), administered by the US Department of Energy, have supported small and medium-sized American manufacturers to reduce energy use and increase their productivity and competitiveness. The 24 IACs, located at premier engineering universities around the country (see below), send faculty and engineering students to local small and medium-sized manufacturers to provide no-cost assessments of energy use, process performance and waste and water flows. Under the direction of experienced professors, IAC engineering students analyze the manufacturer’s facilities, energy bills and energy, waste and water systems, including compressed air, motors/pumps, lighting, process heat and steam. Themore » IACs then follow up with written energy-saving and productivity improvement recommendations, with estimates of related costs and payback periods.« less

Chemical changes in an industrial waste liquid during post-injection movement in a limestone aquifer, Pensacola, Florida

USGS Publications Warehouse

Ehrlich, G.G.; Godsy, E.M.; Pascale, C.A.; Vecchioli, John

1979-01-01

An industrial waste liquid containing organonitrile compounds and nitrate ion has been injected into the lower limestone of the Floridan aquifer near Pensacola, Florida since June 1975. Chemical analyses of water from monitor wells and backflow from the injection well indicate that organic carbon compounds are converted to CO2 and nitrate is converted to N2. These transformations are caused by bacteria immediately after injection, and are virtually completed within 100 m of the injection well. The zone near the injection well behaves like an anaerobic filter with nitrate respiring bacteria dominating the microbial flora in this zone.Sodium thiocyanate contained in the waste is unaltered during passage through the injection zone and is used to detect the degree of mixing of injected waste liquid with native water at a monitor well 312 m (712 ft) from the injection well. The dispersivity of the injection zone was calculated to be 10 m (33 ft). Analyses of samples from the monitor well indicate 80 percent reduction in chemical oxygen demand and virtually complete loss of organonitriles and nitrate from the waste liquid during passage from the injection well to the monitor well. Bacterial densities were much lower at the monitor well than in backflow from the injection well.

A review on applicability of naturally available adsorbents for the removal of hazardous dyes from aqueous waste.

PubMed

Sharma, Pankaj; Kaur, Harleen; Sharma, Monika; Sahore, Vishal

2011-12-01

The effluent water of many industries, such as textiles, leather, paper, printing, cosmetics, etc., contains large amount of hazardous dyes. There is huge number of treatment processes as well as adsorbent which are available for the processing of this effluent water-containing dye content. The applicability of naturally available low cast and eco-friendly adsorbents, for the removal of hazardous dyes from aqueous waste by adsorption treatment, has been reviewed. In this review paper, we have provided a compiled list of low-cost, easily available, safe to handle, and easy-to-dispose-off adsorbents. These adsorbents have been classified into five different categories on the basis of their state of availability: (1) waste materials from agriculture and industry, (2) fruit waste, (3) plant waste, (4) natural inorganic materials, and (5) bioadsorbents. Some of the treated adsorbents have shown good adsorption capacities for methylene blue, congo red, crystal violet, rhodamine B, basic red, etc., but this adsorption process is highly pH dependent, and the pH of the medium plays an important role in the treatment process. Thus, in this review paper, we have made some efforts to discuss the role of pH in the treatment of wastewater.

How to Meet Water Cleanup Deadlines

ERIC Educational Resources Information Center

Schmidt, Richard K.

1976-01-01

Most waste treatment techniques conceived to meet the 1977 standards can be separated into three distinct phases: primary, secondary and tertiary treatment. An examination of the four heaviest industrial water users, pulp and paper, steel, plating, and food processing, demonstrates these treatments use proven technology to meet specific…

FOULING-RESISTANT CERAMIC MEMBRANES FOR TREATMENT OF METASTABLE OIL/WATER EMULSIONS - PHASE I

EPA Science Inventory

Billions of gallons of oily wastewaters are generated daily by a variety of industrial sources. One class of oily wastewaters, metastable oil/water emulsions, encompasses waste streams for which a need exists for more cost-effective and reliable treatment. Current treatment...

Treatment of metal-laden hazardous wastes with advanced clean coal technology by-products. Quarterly report, December 30, 1996--March 30, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-12-31

The objective of this project is to utilize coal ashes to process hazardous materials such as industrial waste water treatment residues, contaminated soils, and air pollution control dusts from the metal industry and municipal waste incineration. This report describes the activities of the project team during the reporting period. The principal work has focused upon continuing evaluation of aged samples from Phase 1, planning supportive laboratory studies for Phase 2, completing scholarly work, reestablishing MAX Environmental Technologies, Inc., as the subcontractor for the field work of Phase 2, proposing two presentations for later in 1997, and making and responding tomore » several outside contacts.« less

Reconnaissance of Organic Wastewater Compounds at a Concentrated Swine Feeding Operation in the North Carolina Coastal Plain, 2008

USGS Publications Warehouse

Harden, Stephen L.

2009-01-01

Water-quality and hydrologic data were collected during 2008 to examine the occurrence of organic wastewater compounds at a concentrated swine feeding operation located in the North Carolina Coastal Plain. Continuous groundwater level and stream-stage data were collected at one monitoring well and one stream site, respectively, throughout 2008. One round of environmental and quality-control samples was collected in September 2008 following a period of below-normal precipitation and when swine waste was not being applied to the spray fields. Samples were collected at one lagoon site, seven shallow groundwater sites, and one surface-water site for analysis of 111 organic wastewater compounds, including household, industrial, and agricultural-use compounds, sterols, pharmaceutical compounds, hormones, and antibiotics. Analytical data for environmental samples collected during the study provide preliminary information on the occurrence of organic wastewater compounds in the lagoon-waste source material, groundwater beneath fields that receive spray applications of the lagoon wastes, and surface water in the tributary adjacent to the site. Overall, 28 organic wastewater compounds were detected in the collected samples, including 11 household, industrial, and agricultural-use compounds; 3 sterols; 2 pharmaceutical compounds; 5 hormones; and 7 antibiotics. The lagoon sample had the greatest number (20) and highest concentrations of compounds compared to groundwater and surface-water samples. The antibiotic lincomycin had the maximum detected concentration (393 micrograms per liter) in the lagoon sample. Of the 11 compounds identified in the groundwater and surface-water samples, all with reported concentrations less than 1 microgram per liter, only lincomycin identified in groundwater at 1 well and 3-methyl-1H-indole and indole identified in surface water at 1 site also were identified in the lagoon waste material.

Recov'Heat: An estimation tool of urban waste heat recovery potential in sustainable cities

NASA Astrophysics Data System (ADS)

Goumba, Alain; Chiche, Samuel; Guo, Xiaofeng; Colombert, Morgane; Bonneau, Patricia

2017-02-01

Waste heat recovery is considered as an efficient way to increase carbon-free green energy utilization and to reduce greenhouse gas emission. Especially in urban area, several sources such as sewage water, industrial process, waste incinerator plants, etc., are still rarely explored. Their integration into a district heating system providing heating and/or domestic hot water could be beneficial for both energy companies and local governments. EFFICACITY, a French research institute focused on urban energy transition, has developed an estimation tool for different waste heat sources potentially explored in a sustainable city. This article presents the development method of such a decision making tool which, by giving both energetic and economic analysis, helps local communities and energy service companies to make preliminary studies in heat recovery projects.

Removal of lead and fluoride from contaminated water using exhausted coffee grounds based bio-sorbent.

PubMed

Naga Babu, A; Reddy, D Srinivasa; Kumar, G Suresh; Ravindhranath, K; Krishna Mohan, G V

2018-07-15

Water pollution by industrial and anthropogenic actives has become a serious threat to the environment. World Health Organization (WHO) has identified that lead and fluoride amid the environmental pollutants are most poisonous water contaminants with devastating impact on the human race. The present work proposes a study on economical bio-adsorbent based technique using exhausted coffee grounds in the removal of lead and fluoride contaminants from water. The exhausted coffee grounds gathered from industrial wastes have been acid-activated and examined for their adsorption capacity. The surface morphology and elemental characterization of pre-and-post adsorption operations by FESEM, EDX and FTIR spectral analysis confirmed the potential of the exhausted coffee ground as successful bio-sorbent. However, thermodynamic analysis confirmed the adsorption to be spontaneous physisorption with Langmuir mode of homogenous monolayer deposition. The kinetics of adsorption is well defined by pseudo second order model for both lead and fluoride. A significant quantity of lead and fluoride is removed from the synthetic contaminated water by the proposed bio-sorbent with the respective sorption capabilities of 61.6 mg/g and 9.05 mg/g. However, the developed bio-sorbent is also recyclable and is capable of removing the lead and fluoride from the domestic and industrial waste-water sources with an overall removal efficiency of about 90%. Copyright © 2018 Elsevier Ltd. All rights reserved.

Adsorbent materials from paper industry waste materials and their use in Cu(II) removal from water.

PubMed

Méndez, A; Barriga, S; Fidalgo, J M; Gascó, G

2009-06-15

This paper deals with the removal of Cu(2+) from water using adsorbent materials prepared from paper industry waste materials (one de-inking paper sludge and other sludge from virgin pulp mill). Experimental results showed that de-inking paper sludge leads to mesoporous materials (V(mic)/V(T)=0.13 and 0.14), whereas the sludge from virgin pulp mill produces high microporous adsorbents (V(mic)/V(T)=0.39 and 0.41). Adsorbent materials were then used for Cu(2+) removal from water at acid pH. During water treatment, heavy metals lixiviation from adsorbent materials was not produced. However, important Ca and Mg leaching was observed. Final pH significantly increases after treatment of water with adsorbent materials probably due to their elevated CaCO(3) content. In general, highest Cu(2+) removal was obtained using adsorbent materials from de-inking paper sludge. This result could be due to their higher content in oxygenated surface groups, high average pore diameter, elevated superficial charge density, high CaCO(3) amount and high Ca and Mg exchange content.

Sources and fate of perfluorinated compounds in the aqueous environment and in drinking water of a highly urbanized and industrialized area in Italy.

PubMed

Castiglioni, Sara; Valsecchi, Sara; Polesello, Stefano; Rusconi, Marianna; Melis, Manuela; Palmiotto, Marinella; Manenti, Angela; Davoli, Enrico; Zuccato, Ettore

2015-01-23

Perfluorinated substances are listed among emerging contaminants because they are globally distributed, environmentally persistent, bioaccumulative and potentially harmful. In a three-year monitoring campaign (2010-2013) we investigated the occurrence, sources and fate of nine perfluoroalkylcarboxylic acids and three perfluoroalkylsulfonic acids, in the most industrialized region of Italy. Composite samples were collected in influents and effluents of wastewater treatment plants (WWTPs), in the main rivers flowing through the basin, and in raw groundwater and finished drinking water. Samples were analyzed by liquid chromatography tandem mass spectrometry. Perfluorinated substances were not removed in WWTPs and those receiving industrial wastes discharged up to 50 times the loads of WWTPs receiving municipal wastes. The mass balance of the emissions in the River Lambro basin showed continuously increasing contamination from north to south and differences in the composition of homologues in the west and east sides of the basin. Ground and drinking water were contaminated in industrial areas, but these substances were removed well in Milan. Contamination from industrial sources was prevalent over urban sources, contributing to 90% of the loads measured at the closure of the basin. The River Lambro was confirmed as one of the main sources of contamination in the Po River. Copyright © 2014 Elsevier B.V. All rights reserved.

Green technology innovation in a developing country

NASA Astrophysics Data System (ADS)

Treesubsuntorn, Chairat; Dolphen, Rujira; Dhurakit, Prapai; Siswanto, Dian; Thiravetyan, Paitip

2017-11-01

Developing countries rapidly grow when green technology, which is referred to as eco-friendly processes or methods, is developed in parallel. Here, some examples of green technology research and development in Thailand will be overviewed. A huge amount of agricultural waste is generated during agricultural processes. Applying these agricultural wastes in order to maximize the benefits for environmental cleanups of water, soil and air has been studied and commercialized. For example: 1) Application of agricultural waste and/or biochar developed from agricultural waste as biological adsorbents for wastewater treatment in some industries, such as textile/dye industries, and printing industries. In addition, this agricultural waste can also be applied in decolorization of sugar syrup from sugar industries; 2) The research on modified biomaterials as adsorbents and packing materials in biofilters would also be presented, and now, pilot scale biofilters have been developed and applied to solve air pollution problems in the field for future commercialization; 3) Some agricultural waste and/or biochar developed from agricultural waste in our laboratory can promote rice growth and improve rice quality via the reduction of Cd uptake and translocation in rice. Phytoremediation technology, in which plants are used to improve the environmental quality in water and air, has also been studied and would be presented. 1) Some species of native Thai plants can effectively remove heavy metals and dye from wastewater. For this research, a constructed wetland for wastewater treatment was developed and applied in a real contaminated site. 2) In air phytoremediation, some plant species harbor highly volatile organic compound (VOC) removal efficiency. In addition, plants do not only absorb organic pollutants, but also they have the innate ability to degrade organic compounds and use them as carbon sources for their growth. In addition, plant growth-promoting (PGP) bacteria inoculation into plants can enhance airborne pollutant removal. From this research, an indoor air phytoremediation system was developed in order to reduce CO2 emissions with high VOC removal efficiency. The high cost of technology transfer is a major problem, especially in developing countries, and green technology research and innovation can overcome this problem along with efficient allocation of resources and technologies.

Detection of Legionella by cultivation and quantitative real-time polymerase chain reaction in biological waste water treatment plants in Norway.

PubMed

Lund, Vidar; Fonahn, Wenche; Pettersen, Jens Erik; Caugant, Dominique A; Ask, Eirik; Nysaeter, Ase

2014-09-01

Cases of Legionnaires' disease associated with biological treatment plants (BTPs) have been reported in six countries between 1997 and 2010. However, knowledge about the occurrence of Legionella in BTPs is scarce. Hence, we undertook a qualitative and quantitative screening for Legionella in BTPs treating waste water from municipalities and industries in Norway, to assess the transmission potential of Legionella from these installations. Thirty-three plants from different industries were sampled four times within 1 year. By cultivation, 21 (16%) of 130 analyses were positive for Legionella species and 12 (9%) of 130 analyses were positive for Legionella pneumophila. By quantitative real-time polymerase chain reaction (PCR), 433 (99%) of 437 analyses were positive for Legionella species and 218 (46%) of 470 analyses were positive for L. pneumophila. This survey indicates that PCR could be the preferable method for detection of Legionella in samples from BTPs. Sequence types of L. pneumophila associated with outbreaks in Norway were not identified from the BTPs. We showed that a waste water treatment plant with an aeration basin can produce high concentrations of Legionella. Therefore, these plants should be considered as a possible source of community-acquired Legionella infections.

Determination of rhodamine B in soft drink, waste water and lipstick samples after solid phase extraction.

PubMed

Soylak, Mustafa; Unsal, Yunus Emre; Yilmaz, Erkan; Tuzen, Mustafa

2011-08-01

A new solid phase extraction method is described for sensitive and selective determination of trace levels of rhodamine B in soft drink, food and industrial waste water samples. The method is based on the adsorption of rhodamine B on the Sepabeads SP 70 resin and its elution with 5 mL of acetonitrile in a mini chromatographic column. Rhodamine B was determined by using UV visible spectrophotometry at 556 nm. The effects of different parameters such as pH, amount of rhodamine B, flow rates of sample and eluent solutions, resin amount, and sample volume were investigated. The influences of some alkali, alkali earth and transition metals on the recoveries of rhodamine B were investigated. The preconcentration factor was found 40. The detection limit based on three times the standard deviation of the reagent blank for rhodamine B was 3.14 μg L⁻¹. The relative standard deviations of the procedure were found as 5% in 1×10⁻⁵ mol L⁻¹ rhodamine B. The presented procedure was successfully applied to real samples including soft drink, food and industrial waste water and lipstick samples. Copyright © 2011 Elsevier Ltd. All rights reserved.

Mercury contamination in chile: a chronicle of a problem foretold.

PubMed

Barrios-Guerra, Carlos A

2004-01-01

This review analyzes the effects of environmental mercury contamination in Chile. This contamination generates one of the most important environmental conflicts in the country in that it affects air, ground, and water (rivers and oceans), which are fundamental in maintaining natural biotic equilibrium and at the same time important for the nation's economy. Chile possesses extraordinarily wealthy mining resources between Regions I and IV that have developed into an extraction industry essential for the economy of the country. However, waste discharges from this production have created an environmental problem in that the majority of the mines are located in the Andes mountain range, or areas close by, and the water used in the extraction process is deposited into the rivers, significantly increasing the amount of chemical contamination. Therefore, the cities and downstream waters used in agriculture suffer the negative consequences of a natural resource that is becoming more and more scarce. In addition, minerals released from mills into the atmosphere are deposited onto the soil, drastically affecting the biological resources of these areas. One of these affected areas is the Metropolitan region, where one of the highest contamination levels of mercury in the country was found in one of its affluents due to industrial and domestic waste discharge. In a country that is only 200 km in width, the gathering of all these contaminants in the rivers results in a rapid flow to the ocean, thereby contaminating coastal waters and the biota. In general, this contamination has been detected in semiclosed bodies of water (bays). Between Regions VII and IX, the principal sources of mercury contamination are related to cellulose industrial sites (Regions VII and VIII) and, until the 1980s, the bleach-soda industry. The most important industrial and fishing activity is also found in this area. In San Vicente Bay, waste discharges released into the ocean include sewage, industrial residues, residues from fishing and mining industries, hydrocarbons, petrochemical derivatives, oils, and detergents. This combination of chemical assault makes the San Vicente Bay the most contaminated in the country and the area where the majority of mercury contamination studies have been carried out. Between Regions X and XII, mercury contamination is reduced due to decreased release of domestic residues, especially batteries and sanitary waste. Beginning with the decade of the 1990s, Chile made a great effort to decrease contamination through governmental organizations (CONAMA, SERNAGEOMIN, DGA, ECOMIN, SONAMI), nongovernmental organizations (NGOs), universities, government mining industries (CODELCO, ENAMI), and private mining industries (El Indio, La Escondida, La Candelaria, Fachinal, etc). These reduction efforts within the last 10 years exceed $900 million, and in the private mining sector alone more than 1,100 monitoring stations have been installed and more than 100,000 environmental measurements have been carried out each year. Furthermore, an important educational program on the use of mercury has been implemented in the small mining area to decrease contamination to the air, water, and soil. However, the consequences of mercury accumulation are seen in their damaging effects to the rivers that deliver water to crops and cities, in the bays where food is extracted, and in the air of some cities where there exist mills that release chemical substances into the atmosphere.

Potential environmental and regulatory implications of naturally occurring radioactive materials (NORM).

PubMed

Paschoa, A S

1998-03-01

The immense volume of naturally occurring radioactive materials (NORM) wastes produced annually by extracting industries throughout the world deserves to come to the attention of international and national environmental protection agencies and regulatory bodies. Although a great deal of work has been done in the fields of radiation protection and remedial actions concerning uranium and other mines, the need to dispose of diffuse NORM wastes will have environmental and regulatory implications that thus far are not fully appreciated. NORM wastes constitute, by and large, unwanted byproducts of industrial activities as diverse as thorium and uranium milling, niobium, tin and gold mining extraction, water treatment, and the production of oil, gas, phosphate fertilizer, coal fire and aluminum. The volumes of NORM wastes produced annually could reach levels so high that the existing low level radioactive waste (LLRW) facilities would be readily occupied by NORM if controlled disposal procedures were not adopted. On the other hand, NORM cannot just be ignored as being below radiological concern (BRC) or lower than exempt concentration levels (ECLs), because sometimes NORM concentrations reach levels as high as 1 x 10(3) kBq/kg for 226Ra, and not much less for 228Ra. Unfortunately, thus far there is not enough information available concerning NORM wastes in key industries, though the international scientific community has been concerned, for a long time now, with technologically enhanced natural radiation exposures (TENRE). This article is written with the intention of examining, to the extent possible, the potential environmental and regulatory implications of NORM wastes being produced in selected industries.

Handling Hot Water, With a Payoff

ERIC Educational Resources Information Center

Stewart, Ronald; Mathur, S. P.

1970-01-01

Discusses methods of utilizing waste heat from the increasing number of power stations. Possible uses include agri- and mariculture, centralized urban and industrial heating, and deicing of airports and marine facilities. (AL)

A proposal for a test method for assessment of hazard property HP 12 ("Release of an acute toxic gas") in hazardous waste classification - Experience from 49 waste.

PubMed

Hennebert, Pierre; Samaali, Ismahen; Molina, Pauline

2016-12-01

A stepwise method for assessment of the HP 12 is proposed and tested with 49 waste samples. The hazard property HP 12 is defined as "Release of an acute toxic gas": waste which releases acute toxic gases (Acute Tox. 1, 2 or 3) in contact with water or an acid. When a waste contains a substance assigned to one of the following supplemental hazards EUH029, EUH031 and EUH032, it shall be classified as hazardous by HP 12 according to test methods or guidelines (EC, 2014a, 2014b). When the substances with the cited hazard statement codes react with water or an acid, they can release HCl, Cl 2 , HF, HCN, PH 3 , H 2 S, SO 2 (and two other gases very unlikely to be emitted, hydrazoic acid HN 3 and selenium oxide SeO 2 - a solid with low vapor pressure). Hence, a method is proposed:For a set of 49 waste, water addition did not produce gas. Nearly all the solid waste produced a gas in contact with hydrochloric acid in 5 min in an automated calcimeter with a volume >0.1L of gas per kg of waste. Since a plateau of pressure is reached only for half of the samples in 5 min, 6 h trial with calorimetric bombs or glass flasks were done and confirmed the results. Identification of the gases by portable probes showed that most of the tested samples emit mainly CO 2 . Toxic gases are emitted by four waste: metallic dust from the aluminum industry (CO), two air pollution control residue of industrial waste incinerator (H 2 S) and a halogenated solvent (organic volatile(s) compound(s)). HF has not been measured in these trials started before the present definition of HP 12. According to the definition of HP 12, only the H 2 S emission of substances with hazard statement EUH031 is accounted for. In view of the calcium content of the two air pollution control residue, the presence of calcium sulphide (EUH031) can be assumed. These two waste are therefore classified potentially hazardous for HP 12, from a total of 49 waste. They are also classified as hazardous for other properties (HP 7, 10and14 for one of them, and HP 10and14 for the other one respectively). Given these results, it can be assumed that few common household and industrial waste will be classified hazardous only by HP 12. Copyright © 2016 Elsevier Ltd. All rights reserved.

40 CFR 105.5 - Who is eligible to win an award?

Code of Federal Regulations, 2010 CFR

2010-07-01

... organizations operate in an industrial capacity in the treatment of wastes or abatement of pollution may be... Section 105.5 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS RECOGNITION AWARDS UNDER THE CLEAN WATER ACT Eligibility Requirements § 105.5 Who is eligible to win an award...

Disinfection of water in recirculating aquaculture systems with peracetic acid

USDA-ARS?s Scientific Manuscript database

Peracetic acid (PAA) has become a favoured alternative to chlorination in the disinfection of municipal waste water in recent years. It is also commonly used in the food industry as a disinfectant. Based on PAA concentration, the disulfide linkage in enzymes and proteins of microorganisms can be bro...

THE FIGHT FOR CLEAN WATER.

ERIC Educational Resources Information Center

SCHOONOVER, ROBERT A.

THIS PUBLICATION DISCUSSES IN DEPTH THE PROBLEM OF WATER POLLUTION AS SEEN BY THE FLORIDA STATE BOARD OF HEALTH. DOMESTIC SEWAGE, INDUSTRIAL WASTES, AND ALLEVIATION ACTIVITIES OF THE STATE BOARD OF HEALTH AND COUNTY HEALTH DEPARTMENTS ARE DESCRIBED. SIX APPENDIXES PRESENT CORRESPONDENCE AND REPORTS REGARDING THE PROBLEM. THIS IS AN ISSUE OF…

26 CFR 1.103-9 - Interest on bonds to finance industrial parks.

Code of Federal Regulations, 2014 CFR

2014-04-01

... installation of incidental water, sewer, sewage and waste disposal, drainage, or similar facilities (whether... transportation facilities, such as hard-surface roads (including curbs and gutters) and railroad spurs and... incidental improvements encompassed by the term, such as, for example, a water pumphouse and storage tank...

26 CFR 1.103-9 - Interest on bonds to finance industrial parks.

Code of Federal Regulations, 2011 CFR

2011-04-01

... installation of incidental water, sewer, sewage and waste disposal, drainage, or similar facilities (whether... transportation facilities, such as hard-surface roads (including curbs and gutters) and railroad spurs and... incidental improvements encompassed by the term, such as, for example, a water pumphouse and storage tank...

26 CFR 1.103-9 - Interest on bonds to finance industrial parks.

Code of Federal Regulations, 2012 CFR

2012-04-01

... installation of incidental water, sewer, sewage and waste disposal, drainage, or similar facilities (whether... transportation facilities, such as hard-surface roads (including curbs and gutters) and railroad spurs and... incidental improvements encompassed by the term, such as, for example, a water pumphouse and storage tank...

26 CFR 1.103-9 - Interest on bonds to finance industrial parks.

Code of Federal Regulations, 2013 CFR

2013-04-01

... installation of incidental water, sewer, sewage and waste disposal, drainage, or similar facilities (whether... transportation facilities, such as hard-surface roads (including curbs and gutters) and railroad spurs and... incidental improvements encompassed by the term, such as, for example, a water pumphouse and storage tank...

Waste heat utilization in industrial processes

NASA Technical Reports Server (NTRS)

Weichsel, M.; Heitmann, W.

1978-01-01

A survey is given of new developments in heat exchangers and heat pumps. With respect to practical applications, internal criteria for plant operation are discussed. Possibilities of government support are pointed out. Waste heat steam generators and waste heat aggregates for hot water generation or in some cases for steam superheating are used. The possibilities of utilization can be classified according to the economic improvements and according to their process applications, for example, gascooling. Examples are presented for a large variety of applications.

Environmental footprints in the meat chain

NASA Astrophysics Data System (ADS)

Đekić, I.; Tomašević, I.

2017-09-01

The objective of this paper was to present environmental performance of the meat chain and highlight main environmental footprints. The meat sector is recognized as one of the leading polluting sectors in the food industry. The meat chain was analyzed from a five-link perspective introducing the following actors: farm(er)s, slaughterhouses, meat processors, customers and consumers. Meat production needs natural resources (water and energy) resulting in waste and waste water discharge. As an outcome it has a high influence on climate change in respect to global warming, acidification and eutrophication potentials and ozone depletion substances.

Combustion quality analysis of briquettes from variety of agricultural waste as source of alternative fuels

NASA Astrophysics Data System (ADS)

Suryaningsih, S.; Nurhilal, O.; Yuliah, Y.; Mulyana, C.

2017-05-01

The increasing in world population and the industrial sector led to increased demand for energy sources. To do this by utilizing the agricultural waste as a fuel source of alternative energy in the form of bio briquette. The aim at this study was to obtain data onto the characteristics of a wide variety of biomass briquettes from waste agricultural industry. The basic ingredients used are biomass waste from coconut husks, sawdust, rice husks and coffee husks. Each of these biomass residues are dried, crushed, then mixed with starch adhesives. This mixture is molded and dried using sunlight. Each type of briquettes was characterized and analyzed the physical-chemical properties, including calorific value, water content, fixed carbon content and the results were compared with charcoal and coal that was used as fuel in public. The results showed that bio briquettes from coconut husks get the highest calorific value of 4,451 cal/g.

Water and health.

PubMed

Guidotti, T L; Conway, J B

1984-10-01

The systems protecting the quality of drinking water in the United States are deteriorating. Many urban water and sewer systems are obsolete. Industrial wastes are imposing a burden on wastewater treatment facilities. In the U.S., outbreaks of water-borne disease are primarily limited to enteritis associated with viruses or Giardia. Issues in the contamination of drinking water by toxic substances include disposal practices, accidental contamination, agricultural runoff and chlorination byproducts. Physicians must support stringent enforcement of water quality standards.

Modification of chitosan by swelling and crosslinking using epichlorohydrin as heavy metal Cr (VI) adsorbent in batik industry wastes

NASA Astrophysics Data System (ADS)

Hastuti, B.; Masykur, A.; Hadi, S.

2016-02-01

Study on chitosan modification by swelling and crosslinking and its application as a selective adsorbent for heavy metals Cr (VI) in batik industry wastes was done. Swelling is intended to improve chitosan porosity, whereas crosslinking is to increase the resistance of chitosan against acid. Natural samples are generally acidic, thus limiting chitosan application as an adsorbent. Modification of chitosan by combining swelling and crosslinking is expected to increase its adsorption capacity in binding heavy metal ions in water. The modified chitosan was later contacted with Cr (VI) to test its adsorption capacity with a variation of pH and contact time. Finally, application of modified chitosan was done in batik industry waste containing Cr (IV). Based on the results, chitosan-ECH 25% (v/v) was the optimum concentration of crosslinker to adsorb Cr (VI) ions. Modified chitosan has a solubility resistance to acids, even though a strong acid. Modification of chitosan also improved its adsorption capacity to Cr (VI) from 74% (pure chitosan) to 89% with contact time 30 min at pH 3. On the application to the batik wastes, the modified chitosan were able to adsorb Cr (IV) up to the level of 5 ppm. Thus, the modified chitosan has a potential to be applied to as an adsorbent of Cr (VI) in batik industry wastes.

Solid recovered fuel production from biodegradable waste in grain processing industry.

PubMed

Kliopova, Irina; Staniskis, Jurgis Kazimieras; Petraskiene, Violeta

2013-04-01

Management of biodegradable waste is one of the most important environmental problems in the grain-processing industry since this waste cannot be dumped anymore due to legal requirements. Biodegradable waste is generated in each stage of grain processing, including the waste-water and air emissions treatment processes. Their management causes some environmental and financial problems. The majority of Lithuanian grain-processing enterprises own and operate composting sites, but in Lithuania the demand for compost is not given. This study focused on the analysis of the possibility of using biodegradable waste for the production of solid recovered fuel, as a local renewable fuel with the purpose of increasing environmental performance and decreasing the direct costs of grain processing. Experimental research with regard to a pilot grain-processing plant has proven that alternative fuel production will lead to minimizing of the volume of biodegradable waste by 75% and the volume of natural gas for heat energy production by 62%. Environmental indicators of grain processing, laboratory analysis of the chemical and physical characteristics of biodegradable waste, mass and energy balances of the solid recovered fuel production, environmental and economical benefits of the project are presented and discussed herein.

Heavy Metal Contamination in Groundwater around Industrial Estate vs Residential Areas in Coimbatore, India

PubMed Central

Mohankumar, K.; Rao, N. Prasada

2016-01-01

Introduction Water is the vital resource, necessary for all aspects of human and ecosystem survival and health. Depending on the quality, bore water may be used for human consumption, irrigation purposes and livestock watering. The quality of bore water can vary widely depending on the quality of ground water that is its source. Pollutants are being added to the ground water system through human and natural processes. Solid waste from industrial units is being dumped near the factories, which react with percolating rainwater and reaches the ground water. The percolating water picks up a large number of heavy metals and reaches the aquifer system and contaminates the ground water. The usage of the contaminated bore water causes the diseases. Mercury, Arsenic and Cadmium are used or released by many industries. Aim This study was conducted to investigate the pollution of bore water in the industrial region (Kurichi Industrial Cluster) of Coimbatore, in the state of Tamilnadu, India. Materials and Methods Four samples were taken from residential areas around Kurichi Industrial Cluster and analysed to find the concentrations of Mercury, Arsenic and Cadmium. Four more samples were taken from other residential regions far from the industrial estate and served as control. Samples were analysed using Atomic absorption spectrophotometry method. Results We found that the ground water of the areas surrounding the industrial cluster does not contain significant amount of those metals. Instead, Heavy metal contamination of ground water were observed in some residential areas of coimbatore. Conclusion The regulatory measures to contain and prevent ground water contamination by industries undertaken by Tamilnadu pollution control board may have lead to absence of heavy metal contamination in Kurichi Industrial cluster, Coimbatore, India. PMID:27190788

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant Conceptual Design Engineering Report (CDER)

NASA Technical Reports Server (NTRS)

1981-01-01

The reference conceptual design of the magnetohydrodynamic (MHD) Engineering Test Facility (ETF), a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commercial feasibility of open cycle MHD, is summarized. Main elements of the design, systems, and plant facilities are illustrated. System design descriptions are included for closed cycle cooling water, industrial gas systems, fuel oil, boiler flue gas, coal management, seed management, slag management, plant industrial waste, fire service water, oxidant supply, MHD power ventilating

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant Conceptual Design Engineering Report (CDER)

NASA Astrophysics Data System (ADS)

1981-09-01

The reference conceptual design of the magnetohydrodynamic (MHD) Engineering Test Facility (ETF), a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commercial feasibility of open cycle MHD, is summarized. Main elements of the design, systems, and plant facilities are illustrated. System design descriptions are included for closed cycle cooling water, industrial gas systems, fuel oil, boiler flue gas, coal management, seed management, slag management, plant industrial waste, fire service water, oxidant supply, MHD power ventilating

Urban metabolism and river systems: an historical perspective - Paris and the Seine, 1790-1970

NASA Astrophysics Data System (ADS)

Barles, S.

2007-06-01

The aim of this paper is to analyse interaction between Paris and the Seine during the industrial era, 1790-1970, a period marked by strong population growth, changes in techniques, and the absence of specific legislation on environmental issues. The viewpoint focuses on exchanges of waters and wastes between city and river, quantifying them and tracing evolution in the light of the strategies implemented by the stakeholders in charge. The study combines industrial ecology, local history and the history of technology. From 1790 to 1850, waste matters, and especially excreta, were considered as raw materials, not refuse: they generated real profits. The removal of human excreta aimed not only at improving urban hygiene, but at producing the fertilizers needed in rural areas. Discharging them into the river was out of the question. But after the 1860s, several factors upset this exploitation, notably domestic water supply. Even so, Parisian engineers continued to process sewage using techniques that would not only ensure hygiene but also conciliate economic and agricultural interests. Both of these early periods are thus noteworthy for a relative limitation of the river's deterioration by urban wastes. Not until the 1920s, when domestic water supply had become the rule and excreta came to be considered as worthless waste, was the principle of valorisation abandoned. This led to important and long-lasting pollution of the Seine, aggravating the industrial pollution that had been in evidence since the 1840s. Analysing the priorities that led to the adoption of one principle or another in matters of urban hygiene and techniques, with the causes and consequences of such changes, enables us to understand the complex relations between Paris and the Seine. From raw material to waste matter, from river to drain, the concept of quality in environment remains the underlying theme.

EPA Collaboration with Sub-Saharan Africa

EPA Pesticide Factsheets

EPA’s environmental program in Sub-Saharan Africa is focused on addressing Africa’s growing urban and industrial pollution issues, such as air quality, water quality, electronics waste and indoor air from cookstoves.

Urban metabolism and river systems: an historical perspective - Paris and the Seine, 1790-1970

NASA Astrophysics Data System (ADS)

Barles, S.

2007-11-01

The aim of this paper is to analyse metabolic interaction between Paris and the Seine during the industrial era, 1790-1970, a period marked by strong population growth, technological changes, and the absence of specific legislation on environmental issues. The viewpoint focuses on exchanges of waters and wastes between city and river, quantifying them and tracing their evolution in the light of the strategies implemented by the stakeholders in charge. The study combines industrial ecology, local history and the history of technology. From 1790 to 1850, waste matters, and especially excreta, were considered as raw materials, not refuse: they generated real profits. The removal of human excreta aimed not only at improving urban hygiene, but at producing the fertilizers needed in rural areas. Discharging them into the river was out of the question. But after the 1860s, several factors upset this exploitation, notably domestic water supply: night soil became more and more liquid, difficult to handle and to turn into fertilizer; once utilised, the water had to be removed from the house; at the same time, the sewerage system developed and had negative impacts on the river. Even so, Parisian engineers continued to process sewage using techniques that would not only ensure hygiene but also conciliate economic and agricultural interests: combined sewerage system and sewage farms. Both of these early periods are thus noteworthy for a relative limitation of the river's deterioration by urban wastes. Not until the 1920s, when domestic water supply had become the standard and excreta came to be considered as worthless waste, was the principle of valorisation abandoned. This led to important and long-lasting pollution of the Seine (despite the construction of a treatment plant), aggravating the industrial pollution that had been in evidence since the 1840s. Analysing the priorities that led to the adoption of one principle or another in matters of urban hygiene and techniques, with the causes and consequences of such changes, enables us to understand the complex relations between Paris and the Seine. From raw material to waste matter, from river to drain, the concept of quality in environment remains the underlying theme.

Integration of Remote Sensing Technology Using Sentinel-2A Satellite images For Fertilization and Water Pollution Analysis in Estuaries Inlet of Semarang Eastern Flood Canal

NASA Astrophysics Data System (ADS)

Subiyanto, Sawitri; Ramadhanis, Zainab; Baktiar, Aditya Hafidh

2018-02-01

One of the waters that has been contaminated by industrial waste and domestic waste is the waters in estuaries inlet of Semarang Eastern Flood Canal which is the estuary of the river system, which passes through the eastern city of Semarang which is dense with residential and industrial. So it is necessary to have information about the assessment of water quality in Estuaries Inlet of Semarang Eastern Flood Canal. Remote sensing technology can analyze the results of recording the spectral characteristics of water with water quality parameters. One of the parameters for assessing water quality is Chlorophyll-a and Total Suspended Solid, can be estimated through remote sensing technology using multispectral Sentinel-2A Satellite images. In this research there are 3 algorithms that will be used in determining the content of chlorophyll a, and for determining TSS. Image accuracy test is done to find out how far the image can give information about Chlorophyll-a and TSS in the waters. The results of the image accuracy test will be compared with the value of chlorophyll-a and TSS that have been tested through laboratory analysis. The result of this research is the distribution map of chlorophyll-a and TSS content in the waters.

National markets for organic waste-derived fertilizers and soil amendments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Logan, T.J.; Pierzynski, G.M.; Pepperman, R.E.

1995-12-31

The last decade has seen enormous growth in the U.S. in the recycling of organic waste materials like sewage sludge, manures, yard waste, solid waste and various industrial wastes. This has been prompted by real or perceived shortages of landfill capacity, state and federal regulations favoring beneficial use of organic wastes, and public support for recycling. Use of fertilizers and soil amendments derived from these wastes has been stimulated by favorable supply-side economics, a shift to organic/sustainable agriculture, and water quality concerns that favor slow-release nutrient sources. This paper summarizes the properties and beneficial use attributes of the various wastesmore » and their derived products, markets for these materials, and constraints/strategies for market penetration.« less

Cellulose nanomaterials as additives for cementitious materials

Treesearch

Tengfei Fu; Robert J. Moon; Pablo Zavatierri; Jeffrey Youngblood; William Jason Weiss

2017-01-01

Cementitious materials cover a very broad area of industries/products (buildings, streets and highways, water and waste management, and many others; see Fig. 20.1). Annual production of cements is on the order of 4 billion metric tons [2]. In general these industries want stronger, cheaper, more durable concrete, with faster setting times, faster rates of strength gain...

Review of Marine Corps Expeditionary Force Preventive Medicine Materiel Requirements

DTIC Science & Technology

2003-12-30

analyses. The theater PM objectives were water sanitation, pest control, heat injury/cold injury prevention, disease surveillance and control, food safety , field sanitation, habitability, waste management, industrial hygiene, and training.

Graphene wrapped Copper Phthalocyanine nanotube: Enhanced photocatalytic activity for industrial waste water treatment

NASA Astrophysics Data System (ADS)

Mukherjee, Moumita; Ghorai, Uttam Kumar; Samanta, Madhupriya; Santra, Angshuman; Das, Gour P.; Chattopadhyay, Kalyan K.

2017-10-01

To improve the photocatalytic performance of metal phthalocyanine based catalyst, Copper Phthalocyanine (CuPc) functionalized reduced graphene oxide (RGO) nanocomposite has been synthesized through a simple chemical approach. The obtained product was characterized by X-ray diffraction technique (XRD), Fourier transform infrared (FTIR) spectroscopy, Ultraviolet-visible spectroscopy (UV-vis) and High resolution transmission electron microscopy (HRTEM). The photocatalytic activity of the RGO/CuPc nanocomposite was performed by the degradation of Rhodamine B (RhB) under visible light irradiation. The photocatalytic studies revealed that the RGO/CuPc nanocomposite exhibits much stronger catalytic behavior than the pristine CuPc nanotube. A plausible mechanism for the photodegradation of Rhodamine B (RhB) was suggested. The RGO wrapped CuPc nanotube composite materials offer great potential as active photocatalysts for degradation of organic pollutions in industrial waste water.

Mapping of chlorophyll a distributions in coastal zones

NASA Technical Reports Server (NTRS)

Johnson, R. W.

1978-01-01

It is pointed out that chlorophyll a is an important environmental parameter for monitoring water quality, nutrient loads, and pollution effects in coastal zones. High chlorophyll a concentrations occur in areas which have high nutrient inflows from sources such as sewage treatment plants and industrial wastes. Low chlorophyll a concentrations may be due to the addition of toxic substances from industrial wastes or other sources. Remote sensing provides an opportunity to assess distributions of water quality parameters, such as chlorophyll a. A description is presented of the chlorophyll a analysis and a quantitative mapping of the James River, Virginia. An approach considered by Johnson (1977) was used in the analysis. An application of the multiple regression analysis technique to a data set collected over the New York Bight, an environmentally different area of the coastal zone, is also discussed.

Waste management to improve food safety and security for health advancement.

PubMed

Lin, Angela Yu-Chen; Huang, Susana Tzy-Ying; Wahlqvist, Mark L

2009-01-01

Economic growth inevitably influences the food chain. Growing demand with changes in lifestyle and health consciousness encourage use of packaged and pre-prepared foods. The needs of environmental protection from waste generated are largely overlooked, and a lack of knowledge about the impact on the environment and its health effects constitute food security/safety problems. Food production and waste generation directly affect resource (i.e., energy and water) consumption and often contaminate the environment. More pressure on food production has inculcated the use of pesticides, herbicides, antibiotics and chemical fertilizers which add to current global pollution. At least half of food grown is discarded before and after it reaches consumers. It is estimated that one third to half of landfill waste comes from the food sector. This landfill releases green house gases (GHG) as well as leachate which worsen soil and water quality and safety. Pharmaceutical and chemical contaminations from residential, industrial and agricultural sources make their way into nearby water and soil and can eventually affect our food systems. Phthalates, PFOA, BPA, commonly used in plastics and personal care products, are found in unacceptable concentrations in Taiwanese waters. They, too, contribute to food contamination and long-term health risk. Existing waste management strategies warrant more stringent norms for waste reduction at source. Awareness through education could reduce food waste and its consequences. This review encompasses impacts of food production systems on the environment, pollution which results from food waste, costs and economic advantages in food waste management, and health consequences of waste.

Potential ability of zeolite to generate high-temperature vapor using waste heat

NASA Astrophysics Data System (ADS)

Fukai, Jun; Wijayanta, Agung Tri

2018-02-01

In various material product industries, a large amount of high temperature steam as heat sources are produced from fossil fuel, then thermal energy retained by condensed water at lower than 100°C are wasted. Thermal energies retained by exhaust gases at lower than 200°C are also wasted. Effective utilization of waste heat is believed to be one of important issues to solve global problems of energy and environment. Zeolite/water adsorption systems are introduced to recover such low-temperature waste heats in this study. Firstly, an adsorption steam recovery system was developed to generate high temperature steam from unused hot waste heat. The system used a new principle that adsorption heat of zeolite/water contact was efficiently extracted. A bench-scaled system was constructed, demonstrating contentious generation of saturated steam nearly 150°C from hot water at 80°C. Energy conservation is expected by returning the generated steam to steam lines in the product processes. Secondly, it was demonstrated that superheated steam/vapor at higher than 200°C could be generated from those at nearly 120°C using a laboratory-scaled setup. The maximum temperature and the time variation of output temperature were successfully estimated using macroscopic heat balances. Lastly, the maximum temperatures were estimated whose saturate air at the relative humidity 20-80% were heated by the present system. Theoretically, air at higher than 200°C was generated from saturate air at higher than 70°C. Consequently, zeolite/water adsorption systems have potential ability to regenerate thermal energy of waste water and exhaust gases.

Health assessment for Master Disposal Service Landfill, Waukesha County, Brookfield, Wisconsin, Region 5. CERCLIS No. WID980820070. Preliminary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-12-10

The Master Disposal Service Landfill is listed on the National Priorities List. The site is located on the western edge of Brookfield in Waukesha County, Wisconsin. From 1962 to 1982, Master Disposal Service, Inc. operated a 40-acre landfill and filled a 26-acre wetland area by accepting in excess of 1.5 million gallons of industrial wastes. The wastes included solvents, paint products, adhesives, oils, and foundry wastes. State sampling established that ground water near the site is contaminated by chromium, lead, phenols, and PCBs. Based on the available information, the site is considered to be of potential public health concern becausemore » of the risk to human health caused by the possibility of exposure to hazardous substances via contaminated ground water, surface water, soil and air.« less

Wyoming's industrial siting permit process and environmental impact assessment

NASA Astrophysics Data System (ADS)

Hyman, Eric L.

1982-01-01

The problem of management of industrial residuals can be reduced through a rational system for siting and planning major industrial facilities. In the United States, Wyoming has moved in the direction of establishing a one-stop permitting system that provides important information for air and water quality planning and solid waste management with a minimum of regulatory overlap. This paper describes Wyoming's Industrial Development Information and Siting Act of 1975 and suggests ways in which the Wyoming permitting system can be improved and applied elsewhere.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matsumura, Yukihiko; Nuessle, F.W.; Antal, M.J. Jr.

Recently, carbonaceous materials including activated carbon were proven to be effective catalysts for hazardous waste gasification in supercritical water. Using coconut shell activated carbon catalyst, complete decomposition of industrial organic wastes including methanol and acetic acid was achieved. During this process, the total mass of the activated carbon catalyst changes by two competing processes: a decrease in weight via gasification of the carbon by supercritical water, or an increase in weight by deposition of carbonaceous materials generated by incomplete gasification of the biomass feedstocks. The deposition of carbonaceous materials does not occur when complete gasification is realized. Gasification of themore » activated carbon in supercritical water is often favored, resulting in changes in the quality and quantity of the catalyst. To thoroughly understand the hazardous waste decomposition process, a more complete understanding of the behavior of activated carbon in pure supercritical water is needed. The gasification rate of carbon by water vapor at subcritical pressures was studied in relation to coal gasification and generating activated carbon.« less

Health assessment for Cemetery Industrial Waste Dump, Rose Township, Michigan, Region 5. CERCLIS No. MID980794663. Preliminary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-06-24

The Cemetery Industrial Waste Dump National Priorities List Site is located in Rose Township, Oakland County, Michigan. Contamination at the site consists of an unknown quantity of buried drums which, when sampled, indicated the presence of metals, polychlorinated biphenyls (PCBs), and halogenated organic compounds. The site is approximately 2-4 acres. In the late 1960s 300 to 600 drums, which contained unknown industrial waste, were illegally buried at the site. Sampling of the drums on-site indicated the presence of several contaminants including: benzene, chlorobenzene, PCBs, arsenic, cadmium, lead, and others. Lead was detected in one monitoring well at 96 micro g/Lmore » and one residential well at a concentration of 61 micro g/L, both are above the Maximum Contaminant Level of 50 micro g/L. Arsenic was detected in the soil at a concentration of 12 mg/Kg. The site is of potential public health concern because of the risk to human health that could result from possible exposure to hazardous substances at levels that may result in adverse health effects. Potential human exposure pathways include direct dermal contact with the soil, the buried drums, and/or ground water; and ingestion of ground water.« less

Impact of industrial phosphate waste discharge on the marine environment in the Gulf of Gabes (Tunisia)

PubMed Central

Stalder, Claudio; Rüggeberg, Andres; Neururer, Christoph; Spangenberg, Jorge E.; Spezzaferri, Silvia

2018-01-01

The marine environment in the Gulf of Gabes (southern Tunisia) is severely impacted by phosphate industries. Nowadays, three localities, Sfax, Skhira and Gabes produce phosphoric acid along the coasts of this Gulf and generate a large amount of phosphogypsum as a waste product. The Gabes phosphate industry is the major cause of pollution in the Gulf because most of the waste is directly discharged into the sea without preliminary treatment. This study investigates the marine environment in the proximity of the phosphate industries of Gabes and the coastal marine environment on the eastern coast of Djerba, without phosphate industry. This site can be considered as "pristine" and enables a direct comparison between polluted and “clean” adjacent areas. Phosphorous, by sequential extractions (SEDEX), Rock-Eval, C, H, N elemental analysis, and stable carbon isotope composition of sedimentary organic matter, X-ray diffraction (qualitative and quantitative analysis) were measured on sediments. Temperature, pH and dissolved oxygen were measured on the water close to the sea floor of each station to estimate environmental conditions. These analyses are coupled with video surveys of the sea floor. This study reveals clear differentiations in pollution and eutrophication in the investigated areas. PMID:29771969

Innovative approach to facilitate reuse of nonhazardous industrial solid waste as building material

DOE Office of Scientific and Technical Information (OSTI.GOV)

St-Laurent, S.G.; Boutin, A.

1997-12-31

The steel industry generates large volumes of inorganic nonhazardous solid waste. During the last five years, Quebec`s steel industry has developed new technologies to recover metal from slags and tailings. Since these processes recover 10 to 30 percent of the metal, large volumes of nonhazardous residues still need to be recycled or disposed of. In order to encourage recycling initiatives, le Ministere de l`Environnement et de la Faune du Quebec (MEF) (Quebec`s Ministry of Environment and Wildlife) established guidelines for the management of nonhazardous industrial solid waste. The aim of these guidelines is to propose a test procedure to evaluatemore » the quality of the material and to define material classes based on their potential for reuse. The evaluation procedure is based on standard tests, generally used for the evaluation of stabilized and solidified hazardous waste. The protocol includes an analysis of the total content of metals in the residue, the determination of the acid neutralization capacity and the prediction of the acid generation potential when the residue contains significant levels of sulfides. The protocol includes three different leachate tests in order to evaluate the mobility of contaminants present in the residue. The leaching procedures are: (1) an equilibrium extraction with water, (2) a modified TCLP extraction, and (3) an acid rain simulation effect extraction. A method is actually under development to collect leachate from a material pile subject to 18 months of rainfall. Materials are categorized into different classes according to their test results. Various potential reuse options are associated with material classes. Evaluation criteria were defined by using water quality standards and results obtained by testing reference construction material supplied by the Quebec`s Ministere des Transports (Ministry of Transportation).« less

Environmental Compliance Assessment Army Reserve (ECAAR)

DTIC Science & Technology

1993-09-01

and water Spent mixed acid Spent caustic Spent sulfuric acid Potential Consequences: Heat generation, violent reaction. Group 2-A Group 2-B Aluminum Any...methane reforming furnaces, pulping liquor recovery furnaces, combustion devices used in the recovery of sulfur values from spent sulfuric acid...Industry and USEPA Hazardous Waste Hazard No. Hazardous Waste Code* Generic FOO1 The spent halogenated solvents used in degreasing: Trichloroethylene, (t

Hydrologic data for a subsurface waste-injection site at Mulberry, Florida; 1972-77

USGS Publications Warehouse

Wilson, William Edward; Parsons, David C.; Spechler, R.M.

1979-01-01

Since October 1972, industrial liquid waste has been injected into a brine aquifer of limestone and dolomite in Mulberry, FL., at a depth of more than 4,000 feet below land surface. During 1977, the injection rate was about 8.8 million gallons per month. To determine what effect the injected waste has on the ground-water body, water levels have been measured and water samples collected from two monitor wells that tap different permeable zones above the injection zone, and from a satellite monitor well that taps the injection zone. The monitor wells are in the annulus of the injection well, and the satellite monitor well is 2,291 feet from the injection well. This report updates previous data reports and includes all hydrologic data collected by the U.S. Geological Survey during 1972-77. Included is a table of well-construction data, a graph showing the volume of waste injected each month, and hydrographs of the annulus monitor wells and the satellite monitor well. (Woodard-USGS)

The importance of ligand speciation in environmental research: a case study.

PubMed

Sillanpää, M; Orama, M; Rämö, J; Oikari, A

2001-02-21

The speciations of EDTA and DTPA in process, waste and river waters are modelled and simulated, specifically to the mode of occurrence in the pulp and paper mill effluents and subsequently in receiving waters. Due to relatively short residence times in bleaching process and waste water treatment and slow exchange kinetics, it is expected that the thermodynamic equilibrium is not necessarily reached. Therefore, the initial speciation plays a key role. As such, the simulations have been extended to the process waters of the pulp and paper industry taking into account estimated average conditions. The results reveal that the main species are; Mn and Ca complexes of EDTA and DTPA in pulp mill process waters; Fe(III) and Mn complexes of EDTA and DTPA in waste waters; Fe(III) and Zn complexes of EDTA and DTPA in receiving waters. It is also shown how the increasing concentration of complexing agents effects the speciation. Alkaline earth metal chelation plays a significant role in the speciation of EDTA and DTPA when there is a noticeable molar excess of complexing agents compared with transition metals.

Histopathological effects of phenol on the digestive gland of amphimelania holandri fer. (gastropoda, prosobranchia)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lajtner, J.; Erben, R.; Klobucar, G.I.V.

1996-12-31

Phenolic wastes are common water pollutants generated from a variety of industrial processes used in oil refineries, gas operations, coke ovens, coal gasification and by natural processes such as the decomposition of plant matter. Relatively high concentrations of phenol are found in rivers near the outlets of channels into which industrial waste waters have been discharged. There are data about the toxic effects of phenol on fish, and on some invertebrates, including snails. However, little is known about histopathological changes induced by phenol`s toxic effects, and these changes might be a basic indicator in assessing the condition of a particularmore » water ecosystem. The existing data are mostly relevant for fish, and we know very little about the snail`s histopathology; however, the snail is a good research model due to its effectiveness as a pollution indicator species. This study attempts to establish the structure of the normal digestive gland and histopathological changes as a result of exposure to phenol. 22 refs., 4 figs.« less

R and D plans for Broad Area Energy Utilization Network System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takemura, Yozo; Ishida, Hiromi; Yanagishita, Hiroshi

1995-12-31

In Japan, approximately 60 percent of the primary energy supply is lost as waste heat due to low thermal energy conversion efficiency. A lot of effort has been made towards energy conservation in industry since 1973 when the oil crisis happened. However, waste heat is not recovered sufficiently at low temperature. Since most of energy in residential and commercial areas is used for air-conditioning and hot water, the temperature of heat for residential and commercial use is almost equal to that of waste heat discharged from industrial sources. Therefore, the Broad Area Energy Utilization Network System (Eco-Energy City) project, whichmore » started in 1993 and will continue over a period of 8 years, is a large-scale national energy conservation project of the Agency of Industrial Science and technology (AIST) of the Ministry of International Trade and Industry (MITI). The aim of this project is to accelerate the full scale utilization of industrial waste heat for residential and commercial use by technological breakthroughs. The concept of the project is as follows: (1) Waste and unutilized heat discharged from industrial sources at relatively high temperature is recovered very efficiently, in multiple stages and in various ways. (2) Recovered heat is transported with a small heat loss over a long distance to residential and commercial areas that have various patterns of consuming relatively low-temperature heat. (3) Transported heat is supplied at consumer sites in different ways depending on the individual consumption pattern. (4) Thermal energy is utilized in the following forms: Cascaded use, combined use and recycling. The key to success is to develop innovative technologies of heat recovery, heat transport, heat supply and systematization of energy supply and demand.« less

Algal turf scrubbing: cleaning surface waters with solar energy while producing a biofuel

USDA-ARS?s Scientific Manuscript database

Throughout the long period of human expansion across the earth, the atmosphere and the earth’s natural waters have been used as low cost sinks or dumps for our human, agricultural and industrial wastes. Despite significant investment, the methods employed for the last half century have largely fail...

Properties of concrete containing foamed concrete block waste as fine aggregate replacement

NASA Astrophysics Data System (ADS)

Muthusamy, K.; Budiea, A. M. A.; Zaidan, A. L. F.; Rasid, M. H.; Hazimmah, D. S.

2017-11-01

Environmental degradation due to excessive sand mining dumping at certain places and disposal of foamed concrete block waste from lightweight concrete producing industry are issues that should be resolved for a better and cleaner environment of the community. Thus, the main intention of this study is to investigate the potential of foamed concrete block waste as partial sand replacement in concrete production. The foamed concrete waste (FCW) used in this research that were supplied by a local lightweight concrete producing industry. The workability and compressive strength of concrete containing various percentage of foamed concrete waste as partial sand replacement has been investigated. Prior to the use, the foamed concrete waste were crushed to produce finer particles. Six concrete mixes containing various content of crushed foamed concrete waste that are 0%, 10%, 20%, 30%, 40% and 50% were used in this experimental work. Then the prepared specimens were placed in water curing until the testing age. Compressive strength test and flexural strength tests were conducted at 7, 14 and 28 days. The result shows that integration of crushed foamed concrete waste as partial sand replacement in concrete reduces the mix workability. It is interesting to note that both compressive strength and flexural strength of concrete improves when 30% crushed foamed concrete waste is added as partial sand replacement.

Use of Eichhornia crassipes modified Nano-chitosan as a biosorbent for lead (II), cadmium (II), and copper (II) ion removal from aqueous solutions

NASA Astrophysics Data System (ADS)

Alkaff, A. H.; Hendri, H.; Farozy, I. H.; Annisa, M.; Aritonang, R. P.

2018-01-01

Industrial waste in a major city poses a considerable threat to water environment from the accumulation of heavy metals. Additionally, uncontrolled growth of Eichhornia crassipes will also damage the water environment by lowering the levels of dissolved oxygen. Therefore, we conduct research to not only treat industrial waste in water but also reduce the population of E. crassipes in water. We made this biosorbent by mixing E. crassipes with nano-chitosan in various compositions. Its absorptivity was tested against single metal solutions of lead (II), cadmium (II), and copper (II) to get the best biosorbent composition. The chosen biosorbent then went through an adsorptivity test against a mixture of three solutions, with each test was carried at various pH. The best biosorbent composition is the mixture of 1 g of E. crassipes with 30 mL of nano-chitosan 0.01%, while adsorption tests in single or three metals solution show that the biosorbent performs better in neutral pH.

The speciation and subtyping of campylobacter isolates from sewage plants and waste water from a connected poultry abattoir using molecular techniques.

PubMed Central

Koenraad, P. M.; Ayling, R.; Hazeleger, W. C.; Rombouts, F. M.; Newell, D. G.

1995-01-01

In this study the distribution of phenotypes of campylobacter strains in sewage and surface waters was investigated by subtyping and by speciation of isolates from various aquatic environments. These environments included two municipal sewage plants (SPA and SPB) and waste water from a poultry abattoir (WWA). Both the sewage plants SPA and SPB collected domestic and industrial waste, and SPA received drain water from WWA. SPB received no waste water from any meat-processing plant. The isolates were speciated by PCR and subtyped by PCR/RFLP based on the flagellin PCR products. From all three reservoirs, no Campylobacter lari was isolated, and approximately 80% of the isolates could be identified as C. jejuni and the rest belonged to the C. coli species. The PCR/RFLP typing technique has a high discrimination level and was reproducible between two separate laboratories. The 182 isolates tested yielded 22 distinct Dde I profiles. The results indicate that strains with profiles found in poultry are also detectable in waste water presumed to be solely from domestic and human sources. In addition some strains were unique to the known poultry-related sources, suggesting that avian-specific strains, non-pathogenic to man, may exist in the environment. In contrast some strains were unique to human waste indicating the potential importance of non-poultry sources of infection. No seasonality was observed in the profile distribution. So, at least in the Netherlands, it is unlikely that infections caused by contaminated surface waters contribute to the seasonality of human campylobacteriosis. Images Fig. 1 PMID:8557080

State of the art: wastewater management in the beverage industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joyce, M.E.; Scaief, J.F.; Cochrane, M.W.

The water pollution impact caused by the wastes from the beverage industry and the methods available to combat the associated problems were studied. The size of each industry is discussed along with production processes, wastewater sources and effluent characteristics. Wastewater management techniques are described in terms of in-plant recycling, by-product recovery and end-of-pipe treatment along with the economics of treatment. The malt liquor, malting, soft drinks and flavoring industries primarily dispose of their effluents in municipal sewers. In-plant recycling and by-product recovery techniques have been developed in these industries to reduce their raw waste load. The wine and brandy andmore » distilled spirits industries in many cases must treat their own effluents so they have developed wastewater management systems including industry-owned treatment plants that yield good effluents. The technology to adequately treat rum distillery wastewater has not been demonstrated. The information basis for this study was a literature search, an effluent guidelines report done for EPA, limited site visits, personal communications and an unpublished report conducted for EPA that included questionaire surveys of the industries.« less

Movement and fate of creosote waste in ground water, Pensacola, Florida; U.S. Geological Survey toxic waste-ground-water contamination program

USGS Publications Warehouse

Mattraw, Harold C.; Franks, Bernard J.

1986-01-01

Ground- and surface-water contamination by pesticides used in the wood-preserving industry is widespread in the United States. Pine poles were treated with wood preservatives from 1902 to 1981 at a creosote works near Pensacola, Florida. Diesel fuel, creosote, and pentachlorophenol were discharged to two unlined impoundments that had a direct hydraulic connection to the sand-and-gravel aquifer. Evidence of wood-preserving waste contamination appears to be confined to the upper 30 meters of the aquifer. The waste plume extends downgradient approximately 300 meters south toward Pensacola Bay. In 1983, the creosote works site was selected by the U.S. Geological Survey's Office of Hazardous Waste Hydrology as a national research demonstration area to apply the latest techniques for characterizing hazardous waste problems. The multidisciplinary research effort is aimed at studying processes that affect the occurrence, transport, transformations, and fate of the toxic contaminants associated with wood preservatives in the environment. Clusters of two to five wells were constructed at different depths at nine sites to define the depth of contamination. Research studies are investigating sorption, dispersion, dilution, chemical reactions, bacterially mediated transformations, quality assurance, plume hydrodynamics, and the ultimate fate of these complex organic wastes.

Biomass waste-to-energy valorisation technologies: a review case for banana processing in Uganda.

PubMed

Gumisiriza, Robert; Hawumba, Joseph Funa; Okure, Mackay; Hensel, Oliver

2017-01-01

Uganda's banana industry is heavily impeded by the lack of cheap, reliable and sustainable energy mainly needed for processing of banana fruit into pulp and subsequent drying into chips before milling into banana flour that has several uses in the bakery industry, among others. Uganda has one of the lowest electricity access levels, estimated at only 2-3% in rural areas where most of the banana growing is located. In addition, most banana farmers have limited financial capacity to access modern solar energy technologies that can generate sufficient energy for industrial processing. Besides energy scarcity and unreliability, banana production, marketing and industrial processing generate large quantities of organic wastes that are disposed of majorly by unregulated dumping in places such as swamps, thereby forming huge putrefying biomass that emit green house gases (methane and carbon dioxide). On the other hand, the energy content of banana waste, if harnessed through appropriate waste-to-energy technologies, would not only solve the energy requirement for processing of banana pulp, but would also offer an additional benefit of avoiding fossil fuels through the use of renewable energy. The potential waste-to-energy technologies that can be used in valorisation of banana waste can be grouped into three: Thermal (Direct combustion and Incineration), Thermo-chemical (Torrefaction, Plasma treatment, Gasification and Pyrolysis) and Biochemical (Composting, Ethanol fermentation and Anaerobic Digestion). However, due to high moisture content of banana waste, direct application of either thermal or thermo-chemical waste-to-energy technologies is challenging. Although, supercritical water gasification does not require drying of feedstock beforehand and can be a promising thermo-chemical technology for gasification of wet biomass such as banana waste, it is an expensive technology that may not be adopted by banana farmers in Uganda. Biochemical conversion technologies are reported to be more eco-friendly and appropriate for waste biomass with high moisture content such as banana waste. Uganda's banana industrialisation is rural based with limited technical knowledge and economic capability to setup modern solar technologies and thermo-conversions for drying banana fruit pulp. This review explored the advantages of various waste-to-energy technologies as well as their shortfalls. Anaerobic digestion stands out as the most feasible and appropriate waste-to-energy technology for solving the energy scarcity and waste burden in banana industry. Finally, potential options for the enhancement of anaerobic digestion of banana waste were also elucidated.

VOLATILE ORGANIC COMPOUNDS (VOC) RECOVERY ...

EPA Pesticide Factsheets

The purpose of the seminar was to bring researchers, technology developers, and industry representatives together to discuss recovery technologies and techniques for VOCs. The seminar focused on the specific VOC recovery needs of industry and on case studies that summarize effective VOC product recovery techniques applicable to air, water, and solid waste. The case studies highlighted examples in which existing and new recovery technologies resulted in significant cost savings to industry. The seminar focused on the following key issues:. Status and future direction of EPA< DOE, and other major research programs.. What are the latest technology innovations in VOC treatment and recovery?. Performance and cost effectiveness of VOC recovery techniques.. How are recovery techniques applied to air, water, and solid waste?Presenters were from industry, academia, EPA, and various consulting firms. The presentations were followed by several facilitated breakout sessions; these sessions allowed participants an opportunity to discuss their needs and opinions on VOC recovery trends, research, and other issues.This document contains summaries of the presentations and discussions during the seminar. It does not constitute an actual proceedings, since the presentations were informal and no written versions were required. The list of participants and contact information are included in Appendix A. Information

Environmental impact of leachate characteristics on water quality.

PubMed

Cumar, Sampath Kumar Mandyam; Nagaraja, Balasubramanya

2011-07-01

Improper urbanization and industrialization are causing a critical stress on groundwater quality in urban areas of the developing countries. The present study under investigation describes the pollution caused by leachate from a waste management site in southwestern Bangalore city causing pollution of the surface water and groundwater reserves. The characterization of 20 groundwater samples and Haralukunte lake sample indicated high pollution of these water reserves by leachate entry into the groundwater and surface water sources. The study area focuses around the solid waste management site, carrying out bio-composting and vermi-composting of municipal solid waste. Further investigations on the severe health problems faced by the public in the study area has revealed a clear pointer towards the usage of polluted water for rearing live-stock, farming, and domestic activities. The characterization of the leachate with high values of BOD at 1,450 mg/l, TDS at 17,200 mg/l, nitrates at 240 mg/l, and MPN at 545/100 ml indicates a clear nuisance potential, which has been substantiated by the characterization of lake water sample with chlorides at 3,400 mg/l, TDS at 8,020 mg/l, and lead and cadmium at 0.18 and 0.08 mg/l, respectively. Analysis of groundwater samples shows alarming physicochemical values closer to the waste disposal site and relatively reduced values away from the source of the waste management site. Bureau of Indian Standards have been adapted as the benchmark for the analysis and validation of observed water quality criteria.

Numerical Simulation of an Industrial Cumulus Affected by Heat, Moisture, and CCN Released from an Oil Refinery.

NASA Astrophysics Data System (ADS)

Guan, S.; Reuter, G. W.

1996-08-01

Large oil refineries emit heat, vapor, and cloud condensation nuclei (CCN), all of which can affect the formation of cloud and precipitation. This study quantities the relative contributions of the three factors on cloud development in calm wind conditions using an axisymmetric cloud model. The factor separation technique is applied to isolate the net contributions of waste heat, vapor, and CCN on the rainfall of a cumulus developing in the industrial plume. The mutual-interactive contributions of two or three of the factors are also computed.The simulations for midlatitude and tropical conditions indicate that the sensible heat provides the major stimulus for cloud development and rain formation. The pure contribution of the industrial CCN is to enhance the condensation, causing an increase in the mass of total cloud water. The simulation results indicate that mutual interactions between waste heat and industrial CCN are large for both cases considered.

Filtration of Runoff From Pressure Washing Vessel Hull in Drydock

DTIC Science & Technology

1995-09-01

the most cost-effective treatment system for particular waste streams, especially heavy metals such as Tributyltin ( TBT ), Lead, Zinc, and Copper...ported the original hypothesis that little dissolved matter was present in the water. Furthermore, it suggested that TBT , if present, was unlikely to be...of the dry dock and that some vessels’ paint systems contained TBT antifoulants, although it was not noted which ones. The Maritime Industrial Waste

Exploring the life cycle management of industrial solid waste in the case of copper slag.

PubMed

Song, Xiaolong; Yang, Jianxin; Lu, Bin; Li, Bo

2013-06-01

Industrial solid waste has potential impacts on soil, water and air quality, as well as human health, during its whole life stages. A framework for the life cycle management of industrial solid waste, which integrates the source reduction process, is presented and applied to copper slag management. Three management scenarios of copper slag are developed: (i) production of cement after electric furnace treatment, (ii) production of cement after flotation, and (iii) source reduction before the recycling process. A life cycle assessment is carried out to estimate the environmental burdens of these three scenarios. Life cycle assessment results showed that the environmental burdens of the three scenarios are 2710.09, 2061.19 and 2145.02 Pt respectively. In consideration of the closed-loop recycling process, the environmental performance of the flotation approach excelled that of the electric furnace approach. Additionally, although flash smelting promotes the source reduction of copper slag compared with bath smelting, it did not reduce the overall environmental burdens resulting from the complete copper slag management process. Moreover, it led to the shifting of environmental burdens from ecosystem quality damage and resources depletion to human health damage. The case study shows that it is necessary to integrate the generation process into the whole life cycle of industrial solid waste, and to make an integrated assessment for quantifying the contribution of source reduction, rather than to simply follow the priority of source reduction and the hierarchy of waste management.

Real Time Monitoring System of Pollution Waste on Musi River Using Support Vector Machine (SVM) Method

NASA Astrophysics Data System (ADS)

Fachrurrozi, Muhammad; Saparudin; Erwin

2017-04-01

Real-time Monitoring and early detection system which measures the quality standard of waste in Musi River, Palembang, Indonesia is a system for determining air and water pollution level. This system was designed in order to create an integrated monitoring system and provide real time information that can be read. It is designed to measure acidity and water turbidity polluted by industrial waste, as well as to show and provide conditional data integrated in one system. This system consists of inputting and processing the data, and giving output based on processed data. Turbidity, substances, and pH sensor is used as a detector that produce analog electrical direct current voltage (DC). Early detection system works by determining the value of the ammonia threshold, acidity, and turbidity level of water in Musi River. The results is then presented based on the level group pollution by the Support Vector Machine classification method.

Possibilities of heat energy recovery from greywater systems

NASA Astrophysics Data System (ADS)

Niewitecka, Kaja

2018-02-01

Waste water contains a large amount of heat energy which is irretrievably lost, so it is worth thinking about the possibilities of its recovery. It is estimated that in a residential building with full sanitary fittings, about 70% of the total tap water supplied is discharged as greywater and could be reused. The subject of the work is the opportunity to reuse waste water as an alternative source of heat for buildings. For this purpose, the design of heat exchangers used in the process of greywater heat recovery in indoor sewage systems, public buildings as well as in industrial plants has been reviewed. The possibility of recovering heat from waste water transported in outdoor sewage systems was also taken into consideration. An exemplary waste water heat recovery system was proposed, and the amount of heat that could be obtained using a greywater heat recovery system in a residential building was presented. The work shows that greywater heat recovery systems allow for significant savings in preheating hot tap water, and the rate of cost reimbursement depends on the purpose of the building and the type of installation. At the same time, the work shows that one should adjust the construction solutions of heat exchangers and indoor installations in buildings to the quality of the medium flowing, which is greywater.

Treatment of industrial effluent water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levitskii, Yu.N.

1982-09-01

This article reports on a thematic exhibition on ''New Developments in Treatment of Natural and Effluent Water'' in the Sanitary-Technical Construction Section at the Exhibition of Achievements of the National Economy of the USSR. The exhibition acquainted visitors with the achievements of leading organizations in different branches of industry with respect to treatment of natural and industrial effluent water. The Kharkov ''Vodkanalproekt'' Institute and the Kharkov affiliate of the All-Union Scientific-Research Institute of Water and Geodesy has jointly developed a ''Polymer-25'' filter for removal of oil products from nonexplosive effluent water discharged by machine building plants. A Baku affiliate hasmore » developed a new ShFP-1 screw-type press filter for dewatering the sediments from water treatment plants as well as for sediments from chemical, food, and other types of plants. The State Institute for Applied Chemistry has designed a continuous process plant for treating effluent water and removing toxic organic waste by converting them into mineral salts with high efficiency.« less

Industrial water supplies of the United States

USGS Publications Warehouse

Love, Samuel K.

1954-01-01

The availability of adequate supplies of water of suitable quality determines in large measure the potential for industrial development in any community. However, the pattern of availability of water for industrial use is not so generally recognized. It is the purpose of this paper to point out the more important factors affecting the distribution and quality of existing and potential sources of water with particular reference to industrial development. From a nation-wide standpoint our country is blessed with plenty of water. If the available water could be distributed completely in accordance with needs, it is probable that no part of the country would suffer from lack of water either now or in the foreseeable future. As nature has not dealt so providently however, or perhaps as man has not been able to cope with the vagaries of nature, we find ourselves beset with droughts and floods. Added to the natural deficiencies of nature are man-made difficulties such as lowered ground-water tables and salt-water encroachment of fresh water supplies resulting from overpumping of ground waters, pollution in all its forms, and wasteful use of water for many purposes. It becomes necessary, therefore, to study and evaluate our most important natural resource in order that we may use it more intelligently. This is particularly true in regard to continued industrial growth of our country.

Remote sensing and laboratory techniques for monitoring ocean dumping

NASA Technical Reports Server (NTRS)

Ohlhorst, C. W.; Johnson, R. W.; Meyer, E. R.

1977-01-01

Results of field experiments conducted in the Atlantic Coastal Zone indicate that plumes resulting from ocean dumping of acid waste and sewage sludge have distinguishable spectral characteristics when the radiance of the pollutant is normalized (ratioed to) background ocean water. Acid waste spectra peak between 550-650 nm while sewage sludge spectra have peak values at wavelengths of about 700 nm or greater. Results indicate that identification of acid waste and sewage sludge plumes may be independent of geographical location in the Atlantic Coastal Zone. Radiance ratio curves obtained in the laboratory qualitatively agree with those obtained from field experiments. Results from the July 25, 1977, Galveston Deep Ocean Dump Site experiment show the radiance ratio curve of the biodigested industrial waste to be fairly flat and similar to the radiance ratio curves of sewage sludge line dumps and sewage sludge spot dumps that have been in the water for several hours.

Consumptive water use associated with food waste: case study of fresh mango in Australia

NASA Astrophysics Data System (ADS)

Ridoutt, B. G.; Juliano, P.; Sanguansri, P.; Sellahewa, J.

2009-07-01

In many parts of the world, freshwater is already a scarce and overexploited natural resource, raising concerns about global food security and damage to freshwater ecosystems. This situation is expected to intensify with the FAO estimating that world food production must double by 2050. Food chains must therefore become much more efficient in terms of consumptive water use. For the small and geographically well-defined Australian mango industry, having an average annual production of 44 692 t of marketable fresh fruit, the average virtual water content (sum of green, blue and gray water) at orchard gate was 2298 l kg-1. However, due to wastage in the distribution and consumption stages of the product life cycle, the average virtual water content of one kg of Australian-grown fresh mango consumed by an Australian household was 5218 l. This latter figure compares to an Australian-equivalent water footprint of 217 l kg-1, which is the volume of direct water use by an Australian household having an equivalent potential to contribute to water scarcity. Nationally, distribution and consumption waste in the food chain of Australian-grown fresh mango to Australian households represented an annual waste of 26.7 Gl of green water and 16.6 Gl of blue water. These findings suggest that interventions to reduce food chain waste will likely have as great or even greater impact on freshwater resource availability as other water use efficiency measures in agriculture and food production.

Hydrothermal Gasification for Waste to Energy

NASA Astrophysics Data System (ADS)

Epps, Brenden; Laser, Mark; Choo, Yeunun

2014-11-01

Hydrothermal gasification is a promising technology for harvesting energy from waste streams. Applications range from straightforward waste-to-energy conversion (e.g. municipal waste processing, industrial waste processing), to water purification (e.g. oil spill cleanup, wastewater treatment), to biofuel energy systems (e.g. using algae as feedstock). Products of the gasification process are electricity, bottled syngas (H2 + CO), sequestered CO2, clean water, and inorganic solids; further chemical reactions can be used to create biofuels such as ethanol and biodiesel. We present a comparison of gasification system architectures, focusing on efficiency and economic performance metrics. Various system architectures are modeled computationally, using a model developed by the coauthors. The physical model tracks the mass of each chemical species, as well as energy conversions and transfers throughout the gasification process. The generic system model includes the feedstock, gasification reactor, heat recovery system, pressure reducing mechanical expanders, and electricity generation system. Sensitivity analysis of system performance to various process parameters is presented. A discussion of the key technological barriers and necessary innovations is also presented.

Determination of cyanide by a highly sensitive indirect spectrophotometric method.

PubMed

Blanco, M; Maspoch, S

1984-01-01

Complexation of Pd(2+) with cyanide inhibits the extraction of the palladium complex of 5-phenylazo-8-aminoquinoline. This effect is used for the indirect spectrophotometric determination of cyanide at the mug level. Cyanide in industrial waste water and in sea-water is determined after distillation as HCN from the sample and collection in sodium hydroxide solution.

[The study of the multifactorial anthropogenic effect on the ecosystems of the industrial reservoirs of "Maiak" industrial complex].

PubMed

Smagin, A I

2006-01-01

The analysis of the ecological situation of the Southern Urals industrial water reservoirs of the nuclear fuel cycle enterprise, "Mayak" PA is represented. The study was held in the 80s - early 90s. The subjects of the study were: a cooling water reservoir--Kysyl-Tash Lake (R-2) as well as a radioactive waste storage reservoir (R-10). Irtyash Lake, which is a drinking water reservoir for the city of Ozyorsk and Alabuga and Kazhakul Lakes, located on the boundary of the Eastern Urals Radioactive Trace (EURT), were taken as control ones. Such water reservoirs as Irtyash, Kysyl-Tash and the waste storage reservoir (R-10) are incorporated into the Techa River basin; while Alabuga and Kazhakul Lakes are related to the interfluve between the Techa River and the Sinara River. The complex effect from such man--caused factors as radiation, chemical and thermal to water reservoirs' ecosystems was studied. Radionuclide specific activities of the major reservoir components (water, bottom sediments, and biological objects), cumulative stock and radiation doses to the biota were determined. Assessment of the condition of biological structures of individual reservoirs was performed. It was found that the long-term complex influence of radiation, thermal and chemical factors resulted in the formation of the unique technology-induced ecosystems being a part of "Mayak" PA process cycle. Radiation doses to the fish of the cooling water reservoir and the radioactive waste storage reservoir were experimentally estimated. These doses from the incorporated beta-emitters were not less then 2-3 Gy/year. The long-term complex influence of radiation and chemical factors didn't cause any irreversible changes either in the fish population or in the ecosystem. Water purity indicators like crayfish (Astacus leptodactilus Esch) and mollusk (Anodonta cygnea L.) were found in the cooling water reservoir. The comparative analysis of the ecological situation of the reservoirs carried out on the basis of several qualitative indicators and with the help of the formalized scoring system allowed determining that the optimum ecological conditions can be observed in Irtyash Lake. The quality of the environment of Alabuga Lake is slightly lower. The ecological conditions in Kysyl-Tash Lake are up to the standard, while in Kazhakul Lake they are lower than the standard. This is the result of the natural salinization of the ecosystem. The lowest indicator was obtained for the radioactive waste storage reservoir.

TREATMENT OF PRODUCED OIL AND GAS WATERS WITH SURFACTANT-MODIFIED ZEOLITE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lynn E. Katz; R.S. Bowman; E.J. Sullivan

2003-11-01

Co-produced water from the oil and gas industry accounts for a significant waste stream in the United States. It is by some estimates the largest single waste stream in the country, aside from nonhazardous industrial wastes. Characteristics of produced water include high total dissolved solids content, dissolved organic constituents such as benzene and toluene, an oil and grease component, and chemicals added during the oil-production process. While most of the produced water is disposed via reinjection, some must be treated to remove organic constituents before the water is discharged. Current treatment options are successful in reducing the organic content; however,more » they cannot always meet the levels of current or proposed regulations for discharged water. Therefore, an efficient, cost-effective treatment technology is needed. Surfactant-modified zeolite (SMZ) has been used successfully to treat contaminated ground water for organic and inorganic constituents. In addition, the low cost of natural zeolites makes their use attractive in water-treatment applications. This report summarizes the work and results of this four-year project. We tested the effectiveness of surfactant-modified zeolite (SMZ) for removal of BTEX with batch and column experiments using waters with BTEX concentrations that are comparable to those of produced waters. The data from our experimental investigations showed that BTEX sorption to SMZ can be described by a linear isotherm model, and competitive effects between compounds were not significant. The SMZ can be readily regenerated using air stripping. We field-tested a prototype SMZ-based water treatment system at produced water treatment facilities and found that the SMZ successfully removes BTEX from produced waters as predicted by laboratory studies. When compared to other existing treatment technologies, the cost of the SMZ system is very competitive. Furthermore, the SMZ system is relatively compact, does not require the storage of potentially hazardous chemicals, and could be readily adapted to an automated system.« less

Remote Sensing and Water Quality Indicators in the West Flood Canal Semarang City: Spatio-temporal Structures of Lansat-8 Derived Chlorophyll-a and Total Suspended Solids

NASA Astrophysics Data System (ADS)

Subiyanto, Sawitri

2017-12-01

One of the waters that has been contaminated by industrial waste and domestic waste is the waters of West Flood Canal in Semarang City which is the estuary of the river system, which passes through the Western City of Semarang which is dense with residential and industrial. So, it is necessary to have information about the assessment of water quality in the estuary of the West Flood Canal. Remote sensing technology can analyze the results of recording the spectral characteristics of water with water quality parameters. One of the parameters for assessing water quality is Chlorophyll-a and Total Suspended Solid, can be estimated through remote sensing technology using multispectral Lansat-8 Satellite images data from April, June, and August, 2017 and there are three selected algorithms. Based on the results of TSS and Chlorophyll-A processing, the TSS shows values greater than or equal to 100 which can be said that West Flood Canal is damaged (hypertrophic). While the chlorophyll-a shows a value less than 100 indicating Eutrophic status (threatened). This is caused by the number of suspended materials in the water surface and also because of the disturbance of water vegetation in the form of weeds that destroy the function of the actual West Canal Flood.

40 CFR Table Tt-1 to Subpart Tt of... - Default DOC and Decay Rate Values for Industrial Waste Landfills

Code of Federal Regulations, 2013 CFR

2013-07-01

... Industrial Waste Landfills TT Table TT-1 to Subpart TT of Part 98 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Industrial Waste... for Industrial Waste Landfills Industry/Waste Type DOC(weight fraction, wet basis) k[dry climatea] (yr...

40 CFR Table Tt-1 to Subpart Tt of... - Default DOC and Decay Rate Values for Industrial Waste Landfills

Code of Federal Regulations, 2014 CFR

2014-07-01

... Industrial Waste Landfills TT Table TT-1 to Subpart TT of Part 98 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Industrial Waste... for Industrial Waste Landfills Industry/Waste Type DOC(weight fraction, wet basis) k[dry climatea] (yr...

Carotenoids, Phenolic Compounds and Tocopherols Contribute to the Antioxidative Properties of Some Microalgae Species Grown on Industrial Wastewater.

PubMed

Safafar, Hamed; van Wagenen, Jonathan; Møller, Per; Jacobsen, Charlotte

2015-12-11

This study aimed at investigating the potential of microalgae species grown on industrial waste water as a new source of natural antioxidants. Six microalgae from different classes, including Phaeodactylum sp. (Bacillariophyceae), Nannochloropsis sp. (Eustigmatophyceae), Chlorella sp., Dunaniella sp., and Desmodesmus sp. (Chlorophyta), were screened for their antioxidant properties using different in vitro assays. Natural antioxidants, including pigments, phenolics, and tocopherols, were measured in methanolic extracts of microalgae biomass. Highest and lowest concentrations of pigments, phenolic compounds, and tocopherols were found in Desmodesmus sp. and Phaeodactylum tricornuotom microalgae species, respectively. The results of each assay were correlated to the content of natural antioxidants in microalgae biomass. Phenolic compounds were found as major contributors to the antioxidant activity in all antioxidant tests while carotenoids were found to contribute to the 1,1-diphenyl-2-picryl-hydrazil (DPPH) radical scavenging activity, ferrous reduction power (FRAP), and ABTS-radical scavenging capacity activity. Desmodesmus sp. biomass represented a potentially rich source of natural antioxidants, such as carotenoids (lutein), tocopherols, and phenolic compounds when cultivated on industrial waste water as the main nutrient source.

Carotenoids, Phenolic Compounds and Tocopherols Contribute to the Antioxidative Properties of Some Microalgae Species Grown on Industrial Wastewater

PubMed Central

Safafar, Hamed; van Wagenen, Jonathan; Møller, Per; Jacobsen, Charlotte

2015-01-01

This study aimed at investigating the potential of microalgae species grown on industrial waste water as a new source of natural antioxidants. Six microalgae from different classes, including Phaeodactylum sp. (Bacillariophyceae), Nannochloropsis sp. (Eustigmatophyceae), Chlorella sp., Dunaniella sp., and Desmodesmus sp. (Chlorophyta), were screened for their antioxidant properties using different in vitro assays. Natural antioxidants, including pigments, phenolics, and tocopherols, were measured in methanolic extracts of microalgae biomass. Highest and lowest concentrations of pigments, phenolic compounds, and tocopherols were found in Desmodesmus sp. and Phaeodactylum tricornuotom microalgae species, respectively. The results of each assay were correlated to the content of natural antioxidants in microalgae biomass. Phenolic compounds were found as major contributors to the antioxidant activity in all antioxidant tests while carotenoids were found to contribute to the 1,1-diphenyl-2-picryl-hydrazil (DPPH) radical scavenging activity, ferrous reduction power (FRAP), and ABTS-radical scavenging capacity activity. Desmodesmus sp. biomass represented a potentially rich source of natural antioxidants, such as carotenoids (lutein), tocopherols, and phenolic compounds when cultivated on industrial waste water as the main nutrient source. PMID:26690454

Toxic legacy: the environmental impact of the manufactured gas industry in the United States.

PubMed

Tarr, Joel A

2014-01-01

The manufactured gas industry provided cities in the United States with energy for light and power during much of the period from approximately 1850 to 1950. This article explores the history of the effects of this industry on air, land, and water environments; it also examines attempts by the courts and municipal and state governments to regulate gas-waste pollution and the industry's response. The article concludes by exploring the heritage of badly contaminated sites that the manufactured gas industry left to the nation after it was replaced by natural gas after World War II.

Heavy equipment maintenance wastes and environmental management in the mining industry.

PubMed

Guerin, Turlough F

2002-10-01

Maintenance wastes, if not managed properly, represent significant environmental issues for mining operations. Petroleum hydrocarbon liquid wastes were studied at an Australian site and a review of the literature and technology vendors was carried out to identify oil/water separation technologies. Treatment technologies and practices for managing oily wastewater, used across the broader mining industry in the Asia-Pacific region, were also identified. Key findings from the study were: (1) primary treatment is required to remove grease oil contamination and to protect secondary oily wastewater treatment systems from being overloaded; (2) selection of an effective secondary treatment system is dependent on influent oil droplet size and concentration, suspended solids concentration, flow rates (and their variability), environmental conditions, maintenance schedules and effectiveness, treatment targets and costs; and (3) oily wastewater treatment systems, based on mechanical separation, are favoured over those that are chemically based, as they simplify operational requirements. Source reduction, through housekeeping, equipment and reagent modifications, and segregation and/or consolidation of hydrocarbon waste streams, minimizes treatment costs, safety and environmental impact.

CONTAINMENT TECHNOLOGY AND MONITORING

EPA Science Inventory

Subsurface vertical barriers have been used to control ground-water seepage in the construction industry for many years. Recently, much attention has been focused on the use of containment technologies as supplemental and stand-alone remedial options for hazardous waste sites to...

Tracking the Global Distribution of Persistent Organic Pollutants Accounting for E-Waste Exports to Developing Regions.

PubMed

Breivik, Knut; Armitage, James M; Wania, Frank; Sweetman, Andrew J; Jones, Kevin C

2016-01-19

Elevated concentrations of various industrial-use Persistent Organic Pollutants (POPs), such as polychlorinated biphenyls (PCBs), have been reported in some developing areas in subtropical and tropical regions known to be destinations of e-waste. We used a recent inventory of the global generation and exports of e-waste to develop various global scale emission scenarios for industrial-use organic contaminants (IUOCs). For representative IUOCs (RIUOCs), only hypothetical emissions via passive volatilization from e-waste were considered whereas for PCBs, historical emissions throughout the chemical life-cycle (i.e., manufacturing, use, disposal) were included. The environmental transport and fate of RIUOCs and PCBs were then simulated using the BETR Global 2.0 model. Export of e-waste is expected to increase and sustain global emissions beyond the baseline scenario, which assumes no export. A comparison between model predictions and observations for PCBs in selected recipient regions generally suggests a better agreement when exports are accounted for. This study may be the first to integrate the global transport of IUOCs in waste with their long-range transport in air and water. The results call for integrated chemical management strategies on a global scale.

2014 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, Mike

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (LA 000161 01, Modification B), for the wastewater land application site at the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond from November 1, 2013–October 31, 2014. The report contains the following information; Facility and system description; Permit required effluent monitoring data and loading rates; Permit required groundwater monitoring data; Status of compliance activities; Noncompliance issues; and Discussion of the facility’s environmental impacts. During the 2014 permit year, approximately 238 million gallons of wastewater were discharged to the Cold Waste Pond. Thismore » is well below the maximum annual permit limit of 375 million gallons. As shown by the groundwater sampling data, sulfate and total dissolved solids concentrations are highest near the Cold Waste Pond and decrease rapidly as the distance from the Cold Waste Pond increases. Although concentrations of sulfate and total dissolved solids are elevated near the Cold Waste Pond, both parameters are below the Ground Water Quality Rule Secondary Constituent Standards in the downgradient monitoring wells.« less

2013 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mike Lewis

2014-02-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (#LA 000161 01, Modification B), for the wastewater land application site at the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond from November 1, 2012–October 31, 2013. The report contains the following information: • Facility and system description • Permit required effluent monitoring data and loading rates • Groundwater monitoring data • Status of compliance activities • Noncompliance issues • Discussion of the facility’s environmental impacts. During the 2013 permit year, approximately 238 million gallons of wastewater was discharged to the Coldmore » Waste Pond. This is well below the maximum annual permit limit of 375 million gallons. As shown by the groundwater sampling data, sulfate and total dissolved solids concentrations are highest near the Cold Waste Pond and decrease rapidly as the distance from the Cold Waste Pond increases. Although concentrations of sulfate and total dissolved solids are elevated near the Cold Waste Pond, both parameters are below the Ground Water Quality Rule Secondary Constituent Standards in the down gradient monitoring wells.« less

2012 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site's Advanced Test Reactor Complex Cold Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mike Lewis

2013-02-01

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (#LA 000161 01, Modification B), for the wastewater land application site at the Idaho National Laboratory Site’s Advanced Test Reactor Complex Cold Waste Pond from November 1, 2011 through October 31, 2012. The report contains the following information: Facility and system description Permit required effluent monitoring data and loading rates Groundwater monitoring data Status of compliance activities Noncompliance issues Discussion of the facility’s environmental impacts During the 2012 permit year, approximately 183 million gallons of wastewater were discharged to the Cold Waste Pond. This ismore » well below the maximum annual permit limit of 375 million gallons. As shown by the groundwater sampling data, sulfate and total dissolved solids concentrations are highest near the Cold Waste Pond and decrease rapidly as the distance from the Cold Waste Pond increases. Although concentrations of sulfate and total dissolved solids are elevated near the Cold Waste Pond, both parameters were below the Ground Water Quality Rule Secondary Constituent Standards in the down gradient monitoring wells.« less

Installation Restoration Program, Phase II (Stage 2-1). Volume 2.

DTIC Science & Technology

1985-05-01

Worthington OH PAGES: 89 SOURCE: Radian Library COMMENTS: General manual for well drilling, sample collection . Includes good elementary background. FIRST... Collected from the Base Industrial and Domestic Waste Water Treatment Plants and Field * Sampling Data PAGES: 75 p. SOURCE: Capt. Mario Ierarti * COMMENTS...Analytical results for samples collected from the * base industrial and domestic wastewater treatment plants have been included. RADIAN FIRST AUTHOR

The advances of Chinese non-ferrous metal mineral industry and its environmental management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miao Zewei; Gao Lin; Zhou Xiaoyuan

1998-12-31

With the steady growth of Chinese economy, the nonferrous metal industry of China was also developed quickly. The gross output of ten main nonferrous metals 4.25 million tons in 1995 so that China ranks the fourth in the world. However, a series of environmental problems also occurred, which relate to characteristics of mineral resources, techniques for mining, dressing, smelting and processing, equipment and their management level. The major pollutants include sulphur dioxide, industrial powder-dust and smoke-dust, water containing heavy metal ions as well as solid wastes. Air, water body, soil, vegetation and people`s health were polluted and damaged to differentmore » extent due to the above pollutants. For the purpose of environmental management and pollution control, some measures must be taken: (1) to strengthen environmental planning, accelerate and perfect environmental laws and related regulations as well as spread the consciousness of environmental protection energetically; (2) to extend cleaner production and adopt advanced technologies so as to reduce environmental pollution; (3) to turn the concept of the end-of-pipe management to the whole-process control; (4) to recovery or reuse the wastes fully. In addition, general situation and policies on reclamation of mining land as well as theory, methods and techniques of restoration of waste land were also stated in the paper.« less

Using S and Pb isotope ratios to trace leaching of toxic substances from an acid-impacted industrial-waste landfill (Pozdatky, Czech Republic).

PubMed

Novak, Martin; Pacherova, Petra; Erbanova, Lucie; Veron, Alain J; Buzek, Frantisek; Jackova, Ivana; Paces, Tomas; Rukavickova, Lenka; Blaha, Vladimir; Holecek, Jan

2012-10-15

Slightly elevated concentrations of toxic species in waters sampled in the surroundings of a leaky landfill may be both a sign of an approaching contaminant plume, or a result of water-rock interaction. Isotopes can be instrumental in distinguishing between anthropogenic and geogenic species in groundwater. We studied sulfur and lead isotope ratios at an abandoned industrial-waste landfill, located in a densely populated part of Central Europe. Stable isotope variability in space and time was used to follow the movement of a groundwater plume, contaminated with toxic metals (Cd, Cr, Be), in fractured granitoids. Toxic metals had been mobilized from industrial waste by a strong pulse of sulfuric acid, also deposited in the landfill. Both tracers exhibited a wide range of values (δ(34)S between +2.6 and +18.9‰; (206)Pb/(207)Pb between 1.16 and 1.39), which facilitated identification of mixing end-members, and made it possible to assess the sources of the studied species. In situ fractionations did not hinder source apportionment. Influx of contaminated groundwater was observed neither in irrigation wells in a nearby village, nor at distances greater than 300 m from the landfill. Combination of stable isotope tracers can be used as part of an early-warning system in landscapes affected by landfills. Copyright © 2012 Elsevier B.V. All rights reserved.

Summary appraisals of the Nation's ground-water resources; South Atlantic Gulf region

USGS Publications Warehouse

Cederstrom, D.J.; Boswell, E.H.; Tarver, G.R.

1979-01-01

Ground-water problems generally are not severe. Critical situations are restricted to areas where large quantities of ground water are being withdrawn or where aquifers are contaminated by oil-field or industrial waste. Large withdrawals in coastal areas have caused some saltwater intrusion. In other localities, highly mineralized water may have migrated along fault zones to freshwater aquifers. Many of the present problems can be resolved or ameliorated by redistributing withdrawals or developing alternative water sources.

Industrial Technology of Decontamination of Liquid Radioactive Waste in SUE MosSIA 'Radon' - 12371

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adamovich, Dmitry V.; Neveykin, Petr P.; Karlin, Yuri V.

SUE MosSIA 'RADON' - this enterprise was created more than 50 years ago, which deals with the recycling of radioactive waste and conditioning of spent sources of radiation in stationary and mobile systems in the own factory and operating organizations. Here is represented the experience SUE MosSIA 'Radon' in the field of the management with liquid radioactive waste. It's shown, that the activity of SUE MosSIA 'RADON' is developing in three directions - improvement of technical facilities for treatment of radioactive waters into SUE MosSIA 'RADON' development of mobile equipment for the decontamination of radioactive waters in other organizations, developmentmore » of new technologies for decontamination of liquid radioactive wastes as part of various domestic Russian and international projects including those related to the operation of nuclear power and nuclear submarines. SUE MosSIA 'RADON' has processed more than 270 thousand m{sup 3} of radioactive water, at that more than 7000 m{sup 3} in other organizations for more than 50 years. It is shown that a number of directions, particularly, the development of mobile modular units for decontamination of liquid radioactive waste, SUE MosSIA 'RADON' is a leader in the world. (authors)« less

Impact of Phosphogypsum waste on the Geochemistry of the coastal water of Ghannouche -Gabes (SE of Tunisia).

NASA Astrophysics Data System (ADS)

Ben Amor, R.; Fathallah, S.; Gueddari, M.

2009-04-01

Impact of Phosphogypsum waste on the Geochemistry of the coastal water of Ghannouche -Gabes (SE of Tunisia). R. Ben Amor, S. Fathallah, M. Gueddari (R.U. of Geochemistry and of Environmental Geology, Faculty of Sciences of Tunis, Department of Geology, 2092 Manar I) Corresponding author: R. Ben Amor; E-mail:magba_rim@yahoo.fr The littoral Ghannouche - Gabes (SE of Tunisia), has been known since the 1970's, an important industrialization especially after the installation of the chemical complex for the treatment of phosphates. These industries are at the origin of various waste materials, the most significant one is phosphogypsum (PG) which is released into the sea. The aim of this paper is to identify and to analyze the different entropic and natural factors, which govern the chemical composition in major elements, dissolved oxygen, pH and temperature of Ghannouche -Gabes coastal water, while studying, in particular, the impact of PG waste on the spatial distribution of these parameters. The result of the chemical analyses of the samples taken in June 2003, show that Na, K and Cl are conserved in solution and they evolve with constant Na/Cl and K/Cl ratio. The values of these ratios are similar to sea water average. The concentration of the other elements are controlled, first, by processes of precipitation or dissolution of the carbonated (Ca, Mg and HCO3) or sulphated (Ca and SO4) minerals, and second, by dilution or evaporation phenomena and by the phosphogypsum waste. The spatial distribution of these elements, of the pH, the dissolved oxygen and the temperature and the result of the saturation index with respect to calcite, gypsum and fluorite, by using of the PhreeqC program, show that the zone, located at north of the study area, between the commercial and the fishing port, is highly influenced by the PG waste. In this area, where the PG is released and which is relatively sheltered by the dams of the commercial and fishing port, waters are characterised by the highest temperatures values, and the lowest pH and the dissolved oxygen values. This water is supersaturated with respect to the fluorite, under saturated with respect to CaCO3 and gypsum. In this zone, the poured gypsum undergoes a quasi-total dissolution. This dissolution would be supported by the acidity of water and the highest temperature values. Keywords: Major ions - Sea water - Phosphogypsum - Saturation indices - Gulf of Gabes - Tunisia.

Aerobic Treatability of Waste Effluent from the Leather Finishing Industry

DTIC Science & Technology

1993-12-01

Thesis in Environmental Engineering by Jeffery A. Vinger Submitted in Partial Fulfillment / of the Requirements Acceslon -for [ for the Degree of NeS CRA...respirometer tests of the raw wastes and mass balance analysis. The results of Phase I were published in a report to the Seton Company as Environmental ...Randall (1992) states that the main driving forces behind the changes in paints and coatings toward water-based mixtures has been the environmental

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Istanbul Water and Sewerage Administration (ISKI) was formed in 1982, and since that time a phased program of sewage collection and treatment has been implemented. Fifteen waste treatment plants, ranging from full scale biological treatment to pre-treatment, are in the design or planning stage, and over 2,000 km of collection lines have been installed. Concurrent with the program is an increasing emphasis on industrial waste treatment, which results in the production of both non-hazardous and hazardous sludges.

Determination of Water Quality Status at Sampean Watershed Bondowoso Residence Using Storet Method

NASA Astrophysics Data System (ADS)

Sugiyarto; Hariono, B.; Destarianto, P.; Nuruddin, M.

2018-01-01

Sampean watershed has an important social and economic function for the people surroundings. Sampean watershed wich cover Bondowoso and Situbondo residence is an urban watershed that has strategic value for national context needs special traetment. Construction activity at upper and lower course of Sampean watershed is highly intensive and growth of inhabitant also increase. The change of land utilization and increase of settlement area at upper, midlle, and lower course caused polutant infiltration to Sampean river watershed so it has impact on water quality. The source of pollution at Sampean river comes from domestic waste, industrial waste, agricultural waste and animal husbandry waste. The purpose of this research is to determine load of pollution and analize the pollution load carrying capacity at Sampean watershed. The data used in this research are rainfall, river flow rate and water quality at 6 certain points within 3 years during 2014 until 2016. The method to determine overall pollution rate is STORET (Storage and Retrieval of Water Quality Data System) method. The analysis results for the first, second, third and forth grade are -24 (moderate quality), -12 (moderate quality), -2 (good quality), and 0 (good quality) respectively.

Preparation and application of unhairing enzyme using solid wastes from the leather industry-an attempt toward internalization of solid wastes within the leather industry.

PubMed

Ramesh, Renganath Rao; Muralidharan, Vimudha; Palanivel, Saravanan

2018-01-01

Usage of the animal fleshing waste as the source of carbon and nitrogen for animal skin unhairing protease (EC 3.4.21) production along with agro-industrial wastes like wheat bran has been investigated. Thermal hydrolysis of delimed fleshing waste for 3 h yielded a fleshing hydrolysate (FH) having a protein content of 20.86 mg/mL and total solids of 46,600 ppm. The FH was lyophilized and spray dried to obtain fleshing hydrolysate powder (FHP) to be used along with wheat bran and rice bran for protease production. The carbon, nitrogen, hydrogen, and sulfur contents of the FHP were found to be 40.1, 13.8, 5.4, and 0.2%. The control solid-state fermented (SSF) medium without FHP showed a maximum activity of only 550 U/g. A maximum protease activity of 956 U/g was obtained by using 6% FHP (taken based on the combined total weight of wheat bran and rice bran) after 96 h of fermentation, resulting in a 1.7-fold increase in the protease activity. The total cost of producing 1 kg of FHP and the cost of producing 1000 kU of protease using FHP along with wheat bran and rice bran were found to be USD 24.62 and USD 2.08, respectively; 25% of SSF protease along with 40% water was found to be capable of unhairing the sheepskins in 7 h eliminating the hazardous conventional lime sulfide unhairing system. Thus, the leather industry's solid waste internalized for the production of unhairing enzyme resulted in a sustainable solution for pollution problems. Graphical abstract ᅟ.

An international perspective on hazardous waste practices.

PubMed

Orloff, Kenneth; Falk, Henry

2003-08-01

In developing countries, public health attention is focused on urgent health problems such as infectious diseases, malnutrition, and infant mortality. As a country develops and gains economic resources, more attention is directed to health concerns related to hazardous chemical wastes. Even if a country has little industry of its own that generates hazardous wastes, the importation of hazardous wastes for recycling or disposal can present health hazards. It is difficult to compare the quantities of hazardous wastes produced in different countries because of differences in how hazardous wastes are defined. In most countries, landfilling is the most common means of hazardous waste disposal, although substantial quantities of hazardous wastes are incinerated in some countries. Hazardous wastes that escape into the environment most often impact the public through air and water contamination. An effective strategy for managing hazardous wastes should encourage waste minimization, recycling, and reuse over disposal. Developing countries are especially in need of low-cost technologies for managing hazardous wastes.

Geology and ground water in Door County, Wisconsin, with emphasis on contamination potential in the Silurian dolomite

USGS Publications Warehouse

Sherrill, Marvin G.

1977-01-01

Door County, a recreational and fruit-growing area bordering Lake Michigan in northeastern Wisconsin, has had a long history of ground-water contamination from surface and near-surface sources. Contamination is most severe in late summer when fruit-canning operations and the influx of tourists create additional wastes. Silurian dolomite is the upper bedrock unit in the county and yields generally adequate supplies of very hard water with locally objectionable concentrations of iron and nitrate. Thin soil cover and well-fractured dolomitic bedrock give easy entry to ground-water contaminants throughout large parts of Door County. Many contaminants enter the dolomite by surface or near-surface seepage. There is little attenuation of contamination concentrations in the well-jointed dolomite, and contaminants may travel long distances underground in a relatively short time. The major source of ground-water contamination is bacteria, from individual waste-disposal systems, agricultural, industrial, and municipal wastes. Areas of the county underlain by contaminated zones include only a small percentage of the total ground-water system and are separated by large volumes of ground water free of contamination. (Woodard-USGS)

Characterization of Jamaican agro-industrial wastes. Part II, fatty acid profiling using HPLC: precolumn derivatization with phenacyl bromide.

PubMed

Bailey-Shaw, Y A; Golden, K D; Pearson, A G M; Porter, R B R

2012-09-01

This paper describes the determination of fatty acid composition of coffee, citrus and rum distillery wastes using reversed-phase high-performance liquid chromatography (RP-HPLC). Lipid extracts of the waste samples are derivatized with phenacyl bromide and their phenacyl esters are separated on a C8 reversed-phase column by using continuous gradient elution with water and acetonitrile. The presence of saturated and unsaturated fatty acids in quantifiable amounts in the examined wastes, as well as the high percentage recoveries, are clear indications that these wastes have potential value as inexpensive sources of lipids. The HPLC procedures described here could be adopted for further analysis of materials of this nature.

A review on water pricing problem for sustainable water resource

NASA Astrophysics Data System (ADS)

Hek, Tan Kim; Ramli, Mohammad Fadzli; Iryanto

2017-05-01

A report that presented at the World Forum II at The Hague in March 2000, said that it would be water crisis around the world and some countries will be lack of water in 2025, as a result of global studies. Inefficient using of water and considering water as free goods which means it can be used as much as we want without any lost. Thus, it causes wasteful consumption and low public awareness in using water without effort to preserve and conserve the water resources. In addition, the excessive exploitation of ground water for industrial facilities also leads to declining of available freshwater. Therefore, this paper reviews some problems arise all over the world regarding to improper and improving management, policies and methods to determine the optimum model of freshwater price in order to avoid its wasteful thus ensuring its sustainability. In this paper, we also proposed a preliminary model of water pricing represents a case of Medan, North Sumatera, Indonesia.

Impact of Climate Change on Soil and Groundwater Chemistry Subject to Process Waste Land Application

NASA Astrophysics Data System (ADS)

McNab, W. W.

2013-12-01

Nonhazardous aqueous process waste streams from food and beverage industry operations are often discharged via managed land application in a manner designed to minimize impacts to underlying groundwater. Process waste streams are typically characterized by elevated concentrations of solutes such as ammonium, organic nitrogen, potassium, sodium, and organic acids. Land application involves the mixing of process waste streams with irrigation water which is subsequently applied to crops. The combination of evapotranspiration and crop salt uptake reduces the downward mass fluxes of percolation water and salts. By carefully managing application schedules in the context of annual climatological cycles, growing seasons, and process requirements, potential adverse environmental impacts to groundwater can be mitigated. However, climate change poses challenges to future process waste land application efforts because the key factors that determine loading rates - temperature, evapotranspiration, seasonal changes in the quality and quantity of applied water, and various crop factors - are all likely to deviate from current averages. To assess the potential impact of future climate change on the practice of land application, coupled process modeling entailing transient unsaturated fluid flow, evapotranspiration, crop salt uptake, and multispecies reactive chemical transport was used to predict changes in salt loading if current practices are maintained in a warmer, drier setting. As a first step, a coupled process model (Hydrus-1D, combined with PHREEQC) was calibrated to existing data sets which summarize land application loading rates, soil water chemistry, and crop salt uptake for land disposal of process wastes from a food industry facility in the northern San Joaquin Valley of California. Model results quantify, for example, the impacts of evapotranspiration on both fluid flow and soil water chemistry at shallow depths, with secondary effects including carbonate mineral precipitation and ion exchange. The calibrated model was then re-run assuming different evapotranspiration and crop growth regimes, and different seasonally-adjusted applied water compositions, to elucidate possible impacts to salt loading reactive chemistry. The results of the predictive modeling indicate the extent to which salts could be redistributed within the soil column as a consequence of climate change. The degree to which these findings are applicable to process waste land application operations at other sites was explored by varying the soil unsaturated flow parameters as a model sensitivity assessment. Taken together, the model results help to quantify operational changes to land application that may be necessary to avoid future adverse environmental impacts to soil and groundwater.

Micron-size metal-binding hydrogel particles improve germination and radicle elongation of Australian metallophyte grasses in mine waste rock and tailings.

PubMed

Guterres, J; Rossato, L; Pudmenzky, A; Doley, D; Whittaker, M; Schmidt, S

2013-03-15

Metal contamination of landscapes as a result of mining and other industrial activities is a pervasive problem worldwide. Metal contaminated soils often lack effective vegetation cover and are prone to contaminant leaching and dispersion through erosion, leading to contamination of the environment. Metal-binding hydrogel particle amendments could ameliorate mine wastes prior to planting and enhance seedling emergence. In this study, micron-size thiol functional cross-linked acrylamide polymer hydrogel particles (X3) were synthesised and tested in laboratory-scale experiments on phytotoxic mine wastes to determine their capacity to: (i) increase substrate water holding capacity (WHC); (ii) reduce metal availability to plants to below the phytotoxicity threshold; and (iii) enhance germination characteristics and early radicle development of two Australian metallophyte grasses under limiting and non-limiting water conditions. Addition of X3 to mine wastes significantly increased their WHC and lowered toxic soluble metal concentrations in mine waste leachates. Germination percentages and radicle elongation of both grasses in wastes were significantly increased. Highest germination percentages and greater radicle development recorded in X3 amended wastes under water limited conditions suggests that X3 was able to ameliorate metal toxicity to radicles, and provide moisture, which improved the imbibition and consequent germination of the seeds. Copyright © 2013 Elsevier B.V. All rights reserved.

Water quality and discharge of streams in the Lehigh River Basin, Pennsylvania

USGS Publications Warehouse

McCarren, Edward F.; Keighton, Walter B.

1969-01-01

The Lehigh River, 100 miles long, is the second largest tributary to the Delaware River. It drains 1,364 square miles in four physiographic provinces. The Lehigh River basin includes mountainous and forested areas, broad agricultural valleys and areas of urban and industrial development. In the headwaters the water is of good quality and has a low concentration of solutes. Downstream, some tributaries receive coal-mine drainage and become acidic; others drain areas underlain by limestone and acquire alkaline characteristics. The alkaline streams neutralize and dilute the acid mine water where they mix. The dissolved-oxygen content of river water, which is high in the upper reaches of the stream, is reduced in the lower reaches because of lower turbulence, higher temperature, and the respiration of organisms. The Lehigh is used for public supply, recreation, waterpower, irrigation, and mining and other industrial purposes. Because the river is shallow in its upper reaches, most of the water comes in contact with the atmosphere as it churns over rocks and around islets and large boulders. Aeration of the water is rapid. When water that was low in dissolved-oxygen concentration was released from the lower strata of the Francis E. Walter Reservoir in June 1966, it quickly became aerated in the Lehigh River, and for 40 miles downstream from the dam the water was nearly saturated with oxygen. Most of the river water requires only moderate treatment for industrial use and public distribution throughout the Lehigh River valley. At times, however, some segments of the main river and its tributaries transport industrial wastes and acid coal-mine drainage. Usually the relatively high concentrations of solutes in water and the ensuing damage caused to quality by such waste discharges are more extensive and prolonged during droughts and other periods of low streamflow. For many years the Lehigh River flow has been continuously measured and its water chemically analyzed. Since May 1966 an instrument installed by the U.S. Geological Survey at Easton, Pa., has continuously recorded such water-quality parameters as specific conductance, temperature, and dissolved oxygen content.

Valorization of Waste Obtained from Oil Extraction in Moringa Oleifera Seeds: Coagulation of Reactive Dyes in Textile Effluents.

PubMed

Vilaseca, Mercè; López-Grimau, Víctor; Gutiérrez-Bouzán, Carmen

2014-09-12

Moringa oleifera seeds contain about 40% of highly valued oil due to its wide range of applications, from nutritional issues to cosmetics or biodiesel production. The extraction of Moringa oil generates a waste (65%-75% of seeds weight) which contains a water soluble protein able to be used either in drinking water clarification or wastewater treatment. In this paper, the waste of Moringa oleifera extraction was used as coagulant to remove five reactive dyes from synthetic textile effluents. This waste constitutes a natural coagulant which was demonstrated to be effective for the treatment of industrial reactive dyestuff effluents, characterized by alkaline pH, high NaCl content and hydrolyzed dyes. The coagulation yield increased at high NaCl concentration, whereas the pH did not show any significant effect on dye removal. Moringa oleifera showed better results for dye removal than the conventional treatment of coagulation-flocculation with FeCl₃ and polyelectrolyte. Treated water can be reused in new dyeing processes of cotton fabrics with high quality results.

Valorization of Waste Obtained from Oil Extraction in Moringa Oleifera Seeds: Coagulation of Reactive Dyes in Textile Effluents

PubMed Central

Vilaseca, Mercè; López-Grimau, Víctor; Gutiérrez-Bouzán, Carmen

2014-01-01

Moringa oleifera seeds contain about 40% of highly valued oil due to its wide range of applications, from nutritional issues to cosmetics or biodiesel production. The extraction of Moringa oil generates a waste (65%–75% of seeds weight) which contains a water soluble protein able to be used either in drinking water clarification or wastewater treatment. In this paper, the waste of Moringa oleifera extraction was used as coagulant to remove five reactive dyes from synthetic textile effluents. This waste constitutes a natural coagulant which was demonstrated to be effective for the treatment of industrial reactive dyestuff effluents, characterized by alkaline pH, high NaCl content and hydrolyzed dyes. The coagulation yield increased at high NaCl concentration, whereas the pH did not show any significant effect on dye removal. Moringa oleifera showed better results for dye removal than the conventional treatment of coagulation-flocculation with FeCl3 and polyelectrolyte. Treated water can be reused in new dyeing processes of cotton fabrics with high quality results. PMID:28788199

a Study for Remote Detection of Industrial Effluents' Effect on Rice Using Thermal Images

NASA Astrophysics Data System (ADS)

Dehnavi, S.; Abkar, A. A.; Maghsoudi, Y.; Dehnavi, E.

2015-12-01

Rice is one of the most important nutritious grains all over the world, so that only in some parts of Asia more than 300 million acres allocated for cultivating this product. Therefore, qualitative and quantitative management of this product is of great importance in commercial, political and financial viewpoints. Rice plant is very influenced by physical and chemical characteristics of irrigation water, due to its specific kind of planting method. Hence, chemically-polluted waters which received by plant can change in live plants and their products. Thus, a very high degree of treatment will be required if the effluent discharges to rice plants. Current waters receive a variety of land-based water pollutants ranging from industrial wastes to excess sediments. One of the most hazardous wastes are chemicals that are toxic. Some factories discharge their effluents directly into a water body. So, what would happen for rice plant or its product if this polluted water flow to paddies? Is there any remotely-based method to study for this effect? Are surface temperature distributions (thermal images) useful in this context? The first goal in this research is thus to investigate the effect of a simulated textile factory's effluent sample on the rice product. The second goal is to investigate whether the polluted plant can be identified by means of thermal remote sensing or not. The results of this laboratory research have proven that the presence of industrial wastewater cause a decrease in plant's product and its f-cover value, also some changes in radiant temperature.

Enhanced photocatalytic performance of CeO2-TiO2 nanocomposite for degradation of crystal violet dye and industrial waste effluent

NASA Astrophysics Data System (ADS)

Zahoor, Mehvish; Arshad, Amara; Khan, Yaqoob; Iqbal, Mazhar; Bajwa, Sadia Zafar; Soomro, Razium Ali; Ahmad, Ishaq; Butt, Faheem K.; Iqbal, M. Zubair; Wu, Aiguo; Khan, Waheed S.

2018-03-01

This study presents the synthesis of CeO2-TiO2 nanocomposite and its potential application for the visible light-driven photocatalytic degradation of model crystal violet dye as well as real industrial waste water. The ceria-titania (CeO2-TiO2) nanocomposite material was synthesised using facile hydrothermal route without the assistance of any template molecule. As-prepared composite was characterised by SEM, TEM, HRTEM, XRD, XPS for surface features, morphological and crystalline characters. The formed nanostructures were determined to possess crystal-like geometrical shape and average size less than 100 nm. The as-synthesised nanocomposite was further investigated for their heterogeneous photocatalytic potential against the oxidative degradation of CV dye taken as model pollutant. The photo-catalytic performance of the as-synthesised material was evaluated both under ultra-violet as well as visible light. Best photocatalytic performance was achieved under visible light with complete degradation (100%) exhibited within 60 min of irradiation time. The kinetics of the photocatalytic process were also considered and the reaction rate constant for CeO2-TiO2 nanocomposite was determined to be 0.0125 and 0.0662 min-1 for ultra-violet and visible region, respectively. In addition, the as-synthesised nanocomposite demonstrated promising results when considered for the photo-catalytic degradation of coloured industrial waste water collected from local textile industry situated in Faisalabad region of Pakistan. Enhanced photo-catalytic performance of CeO2-TiO2 nanocomposite was proposed owing to heterostructure formation leading to reduced electron-hole recombination.

Screening and Quantification of Aliphatic Primary Alkyl Corrosion Inhibitor Amines in Water Samples by Paper Spray Mass Spectrometry.

PubMed

Jjunju, Fred P M; Maher, Simon; Damon, Deidre E; Barrett, Richard M; Syed, S U; Heeren, Ron M A; Taylor, Stephen; Badu-Tawiah, Abraham K

2016-01-19

Direct analysis and identification of long chain aliphatic primary diamine Duomeen O (n-oleyl-1,3-diaminopropane), corrosion inhibitor in raw water samples taken from a large medium pressure water tube boiler plant water samples at low LODs (<0.1 pg) has been demonstrated for the first time, without any sample preparation using paper spray mass spectrometry (PS-MS). The presence of Duomeen O in water samples was confirmed via tandem mass spectrometry using collision-induced dissociation and supported by exact mass measurement and reactive paper spray experiments using an LTQ Orbitrap Exactive instrument. Data shown herein indicate that paper spray ambient ionization can be readily used as a rapid and robust method for in situ direct analysis of polymanine corrosion inhibitors in an industrial water boiler plant and other related samples in the water treatment industry. This approach was applied for the analysis of three complex water samples including feedwater, condensate water, and boiler water, all collected from large medium pressure (MP) water tube boiler plants, known to be dosed with varying amounts of polyamine and amine corrosion inhibitor components. Polyamine chemistry is widely used for example in large high pressure (HP) boilers operating in municipal waste and recycling facilities to prevent corrosion of metals. The samples used in this study are from such a facility in Coventry waste treatment facility, U.K., which has 3 × 40 tonne/hour boilers operating at 17.5 bar.

Determination of toxic inorganic elements pollution in ground waters of Kahuta Industrial Triangle Islamabad, Pakistan using inductively coupled plasma mass spectrometry.

PubMed

Kausar, Rubina; Ahmad, Zulfiqar

2009-10-01

The present study deals with the ground water quality assessment in Kahuta Industrial Triangle Islamabad, Pakistan. The objective of the study was to assess ground water quality against the drinking water standards for various toxic inorganic elements. Representative groundwater samples were collected and analyzed in the Water Quality Laboratory of Pakistan Council of Research in Water Resources (PCRWR) at Islamabad, Pakistan. The samples were run on ICP-MS (Inductively coupled plasma mass spectrometry), which has the capability to separate and quantify 70 elements at a time. One of the finding of study is that ICP-MS is a very good tool to analyze broad range of toxic inorganic elements to the level of parts per billion (ppb). World Health Organization drinking water standards shows that these toxic inorganic elements such as heavy metals even at this concentration level (ppb) are injurious to human health. This analysis indicated pollution of various toxic elements including Selenium. Vertical leachate through industrial waste septic tanks is identified as major cause of groundwater pollution in the Industrial Triangle. Monitoring of the septic tanks and groundwater quality in study area is suggested along with remedial measures.

Sustainable sources of biomass for bioremediation of heavy metals in waste water derived from coal-fired power generation.

PubMed

Saunders, Richard J; Paul, Nicholas A; Hu, Yi; de Nys, Rocky

2012-01-01

Biosorption of heavy metals using dried algal biomass has been extensively described but rarely implemented. We contend this is because available algal biomass is a valuable product with a ready market. Therefore, we considered an alternative and practical approach to algal bioremediation in which algae were cultured directly in the waste water stream. We cultured three species of algae with and without nutrient addition in water that was contaminated with heavy metals from an Ash Dam associated with coal-fired power generation and tested metal uptake and bioremediation potential. All species achieved high concentrations of heavy metals (to 8% dry mass). Two key elements, V and As, reached concentrations in the biomass of 1543 mg.kg(-1) DW and 137 mg.kg(-1) DW. Growth rates were reduced by more than half in neat Ash Dam water than when nutrients were supplied in excess. Growth rate and bioconcentration were positively correlated for most elements, but some elements (e.g. Cd, Zn) were concentrated more when growth rates were lower, indicating the potential to tailor bioremediation depending on the pollutant. The cosmopolitan nature of the macroalgae studied, and their ability to grow and concentrate a suite of heavy metals from industrial wastes, highlights a clear benefit in the practical application of waste water bioremediation.

Development and characterization of a new encapsulating agent from orange juice by-products.

PubMed

Kaderides, Kyriakos; Goula, Athanasia M

2017-10-01

The replacement of maltodextrins as carriers for the spray drying of sticky and sugar based bioactives is an important development for the food industry. In this work, orange juice industry by-product was used to obtain a high dietary fiber powder to be used as carrier material. This powder was characterized with respect to its physical and chemical properties related to the process of encapsulation by spray drying. Adsorption isotherms of orange waste powder were determined at 30, 45, and 60°C. The data were fitted to several models including two-parameter (BET, Halsey, Smith, and Oswin), three-parameter (GAB), and four-parameter (Peleg) relationships. The GAB model best fitted the experimental data. The isosteric heat of sorption was determined from the equilibrium sorption data using the Clausius-Clapeyron equation. Isosteric heats of sorption were found to decrease exponentially with increasing moisture content. The enthalpy-entropy compensation theory was applied to the sorption isotherms and indicated an enthalpy controlled sorption process. Glass transition temperatures (T g ) of orange waste powder conditioned at various water activities were determined and a strong plasticizing effect of water on T g was found. These data were satisfactory correlated by the Gordon and Taylor model. The critical water activity and moisture content for the orange waste powder were 0.82 and 0.18g water/g solids, respectively, at a storage temperature of 25°C. Copyright © 2017 Elsevier Ltd. All rights reserved.

Uranium-mediated electrocatalytic dihydrogen production from water.

PubMed

Halter, Dominik P; Heinemann, Frank W; Bachmann, Julien; Meyer, Karsten

2016-02-18

Depleted uranium is a mildly radioactive waste product that is stockpiled worldwide. The chemical reactivity of uranium complexes is well documented, including the stoichiometric activation of small molecules of biological and industrial interest such as H2O, CO2, CO, or N2 (refs 1 - 11), but catalytic transformations with actinides remain underexplored in comparison to transition-metal catalysis. For reduction of water to H2, complexes of low-valent uranium show the highest potential, but are known to react violently and uncontrollably forming stable bridging oxo or uranyl species. As a result, only a few oxidations of uranium with water have been reported so far; all stoichiometric. Catalytic H2 production, however, requires the reductive recovery of the catalyst via a challenging cleavage of the uranium-bound oxygen-containing ligand. Here we report the electrocatalytic water reduction observed with a trisaryloxide U(III) complex [(((Ad,Me)ArO)3mes)U] (refs 18 and 19)--the first homogeneous uranium catalyst for H2 production from H2O. The catalytic cycle involves rare terminal U(IV)-OH and U(V)=O complexes, which have been isolated, characterized, and proven to be integral parts of the catalytic mechanism. The recognition of uranium compounds as potentially useful catalysts suggests new applications for such light actinides. The development of uranium-based catalysts provides new perspectives on nuclear waste management strategies, by suggesting that mildly radioactive depleted uranium--an abundant waste product of the nuclear power industry--could be a valuable resource.

Economic and environmental optimization of a multi-site utility network for an industrial complex.

PubMed

Kim, Sang Hun; Yoon, Sung-Geun; Chae, Song Hwa; Park, Sunwon

2010-01-01

Most chemical companies consume a lot of steam, water and electrical resources in the production process. Given recent record fuel costs, utility networks must be optimized to reduce the overall cost of production. Environmental concerns must also be considered when preparing modifications to satisfy the requirements for industrial utilities, since wastes discharged from the utility networks are restricted by environmental regulations. Construction of Eco-Industrial Parks (EIPs) has drawn attention as a promising approach for retrofitting existing industrial parks to improve energy efficiency. The optimization of the utility network within an industrial complex is one of the most important undertakings to minimize energy consumption and waste loads in the EIP. In this work, a systematic approach to optimize the utility network of an industrial complex is presented. An important issue in the optimization of a utility network is the desire of the companies to achieve high profits while complying with the environmental regulations. Therefore, the proposed optimization was performed with consideration of both economic and environmental factors. The proposed approach consists of unit modeling using thermodynamic principles, mass and energy balances, development of a multi-period Mixed Integer Linear Programming (MILP) model for the integration of utility systems in an industrial complex, and an economic/environmental analysis of the results. This approach is applied to the Yeosu Industrial Complex, considering seasonal utility demands. The results show that both the total utility cost and waste load are reduced by optimizing the utility network of an industrial complex. 2009 Elsevier Ltd. All rights reserved.

Characterizing Concentrations and Size Distributions of Metal-Containing Nanoparticles in Waste Water

EPA Science Inventory

Nanomaterials containing metals are finding increasing use in consumer, industrial, and medical products, and they are subsequently being released into the environment. Methods for detecting, quantifying, and characterizing these materials in complex matrices are critical for the...

TRACE GAS CONCENTRATIONS IN STREAMS - EARLY WARNING INDICATORS OF STREAM IMPAIRMENT?

EPA Science Inventory

Surface water contamination and resultant impairment of aquatic ecosystem functioning are serious environmental problems, caused in large part by land use changes and excess organic waste inputs associated with agriculture and residential and industrial development. Headwater st...

MODELING IN CSO MANAGEMENT

EPA Science Inventory

Combined sewer overflows (CSOs) contain not only stormwater but also untreated human and industrial waste, toxic materials, and debris. Since the 1960's, CSOs have been recognized as a significant threat to water quality and public health for more than 1000 communities which serv...

Uranium Mines and Mills | RadTown USA | US EPA

EPA Pesticide Factsheets

2017-08-07

Uranium is used as nuclear fuel for electric power generation. U.S. mining industries can obtain uranium in two ways: mining or milling. Mining waste and mill tailings can contaminate water, soil and air if not disposed of properly.

Two Virus Based Endocrine Disruptor Assays Effective Across Vertebrate Classes.

EPA Science Inventory

The presence of hormone mimics, or endocrine disrupting compounds (EDC’s), in the environment are increasing. Sources range from agricultural run–off, pharmaceuticals in waste water, to industrial operations. Current levels of contamination are sufficient to alter sexual develo...

Stabilization/solidification of an alkyd paint waste by carbonation of waste-lime based formulations.

PubMed

Arce, R; Galán, B; Coz, A; Andrés, A; Viguri, J R

2010-05-15

The application of solvent-based paints by spraying in paint booths is extensively used in a wide range of industrial activities for the surface treatment of a vast array of products. The wastes generated as overspray represent an important environmental and managerial problem mainly due to the hazardous characteristics of the organic solvent, rendering it necessary to appropriately manage this waste. In this paper a solidification/stabilization (S/S) process based on accelerated carbonation was investigated as an immobilization pre-treatment prior to the disposal, via landfill, of an alkyd solvent-based paint waste coming from the automotive industry; the purpose of this S/S process was to immobilize the contaminants and reduce their release into the environment. Different formulations of paint waste with lime, lime-coal fly-ash and lime-Portland cement were carbonated to study the effect of the water/solid ratio and carbonation time on the characteristics of the final product. To assess the efficiency of the studied S/S process, metals, anions and dissolved organic carbon (DOC) were analyzed in the leachates obtained from a battery of compliance and characterization leaching tests. Regarding the carbonation of paint waste-lime formulations, a mathematical expression has been proposed to predict the results of the leachability of DOC from carbonated mixtures working at water/solid ratios from 0.2 to 0.6. However, lower DOC concentrations in leachates (400mg/kg DOC in L/S=10 batch leaching test) were obtained when carbonation of paint waste-lime-fly-ash mixtures was used at 10h carbonation and water to solid ratio of 0.2. The flammability characteristics, the total contents of contaminants and the contaminant release rate in compliance leaching tests provide evidence for a final product suitable for deposition in non-hazardous landfills. The characterization of this carbonated sample using a dynamic column leaching test shows a high stabilization of metals, partial immobilization of Cl(-), SO(4)(2-), F(-) and limited retention of DOC. However, the obtained results improve the previous findings obtained after the paint waste S/S using uncarbonated formulations and would be a useful pre-treatment technique of the alkyd paint waste prior to its disposal in a landfill. Copyright (c) 2009 Elsevier B.V. All rights reserved.

Fleet Readiness Center - Southeast Technology Development Program (Cadmium & Hexavalent Chromium Reduction)

DTIC Science & Technology

2014-11-01

Industrial Waste Water Treatment  Aircraft & Component Paint Removal (ABM & Chemical)  Chrome Electroplating  Corrosion Treatment  Aircraft...Hex Chrome post treatment )  Energy Use; Electrical (& Steam)  NDI- Florescent Penetrant  Solvent Tank Cleaning  Water (& Sanitary) Use...Engineer Corrosion Science & Engineering NAVAIR Jacksonville Phone: (904) 790-6405 Email: john.benfer@navy.mil ASETS Technical Workshop (NOV

Monitoring of impact of anthropogenic inputs on water quality of mangrove ecosystem of Uran, Navi Mumbai, west coast of India.

PubMed

Pawar, Prabhakar R

2013-10-15

Surface water samples were collected from substations along Sheva creek and Dharamtar creek mangrove ecosystems of Uran (Raigad), Navi Mumbai, west coast of India. Water samples were collected fortnightly from April 2009 to March 2011 during spring low and high tides and were analyzed for pH, Temperature, Turbidity, Total solids (TS), Total dissolved solids (TDS), Total suspended solids (TSS), Dissolved oxygen (DO), Biochemical oxygen demand (BOD), Carbon dioxide (CO2), Chemical oxygen demand (COD), Salinity, Orthophosphate (O-PO4), Nitrite-nitrogen (NO2-N), Nitrate-nitrogen (NO3-N), and Silicates. Variables like pH, turbidity, TDS, salinity, DO, and BOD show seasonal variations. Higher content of O-PO4, NO3-N, and silicates is recorded due to discharge of domestic wastes and sewage, effluents from industries, oil tanking depots and also from maritime activities of Jawaharlal Nehru Port Trust (JNPT), hectic activities of Container Freight Stations (CFS), and other port wastes. This study reveals that water quality from mangrove ecosystems of Uran is deteriorating due to industrial pollution and that mangrove from Uran is facing the threat due to anthropogenic stress. Copyright © 2013 Elsevier Ltd. All rights reserved.

Water pollution and habitat degradation in the Gulf of Thailand.

PubMed

Cheevaporn, Voravit; Menasveta, Piamsak

2003-01-01

The Gulf of Thailand has been a major marine resource for Thai people for a long time. However, recent industrialization and community development have exerted considerable stress on the marine environments and provoked habitat degradation. The following pollution problems in the Gulf have been prioritized and are discussed in details: (1) Untreated municipal and industrial waste water are considered to be the most serious problems of the country due to limited waste water treatment facilities in the area. (2) Eutrophication is an emerging problem in the gulf of Thailand. Fortunately, the major species of phytoplankton that have been reported as the cause of red tide phenomena were non-toxic species such as Noctiluca sp. and Trichodesmium sp. (3) Few problems have been documented from trace metals contamination in the Gulf of Thailand and public health threat from seafood contamination does not appear to be significant yet. (4) Petroleum hydrocarbon residue contamination is not a problem, although a few spills from small oil tankers have been recorded. A rapid decrease in mangrove forest, coral reefs, and fisheries resources due to mismanagement is also discussed.

Steam ejector as an industrial heat pump

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnold, H.G.; Huntley, W.R.; Perez-Blanco, H.

1982-01-01

The steam ejector is analyzed for use in industrial heat recovery applications and compared to mechanical compressor heat pumps. An estimated ejector performance was analyzed using methods based on conservation of mass, momentum, and energy; using steam properties to account for continuity; and using appropriate efficiencies for the nozzle and diffuse performance within the ejector. A potential heat pump application at a paper plant in which waste water was available in a hot well downstream of the paper machine was used to describe use of the stream ejector. Both mechanical compression and jet ejector heat pumps were evaluated for recompressionmore » of flashed steam from the hot well. It is noted that another possible application of vapor recompression heat pumps is the recovery of waste heat from large facilities such as the gaseous diffusion plants. The economics of recovering waste heat in similar applications is analyzed. (MCW)« less

The Development of Environmentally Friendly Technologies of Using Coals and Products of Their Enrichment in the Form of Coal Water Slurries

NASA Astrophysics Data System (ADS)

Murko, Vasily; Hamalainen, Veniamin

2017-11-01

The article presents the current state of the technology for production and combustion of fuel coal water slurries in Russia and foreign countries. Experimental and industrial facilities show the technological and economic efficiency of using this technology for disposal of wastes resulting after coal processing and enrichment. The feasibility studies of use of the technology at large Kuzbass thermal power stations are presented. The possibility of solving a serious environmental problem of reducing storage of the most toxic waste of coal enrichment in the location areas of coal washing plants and coal mining enterprises is demonstrated.

A critical review on textile wastewater treatments: Possible approaches.

PubMed

Holkar, Chandrakant R; Jadhav, Ananda J; Pinjari, Dipak V; Mahamuni, Naresh M; Pandit, Aniruddha B

2016-11-01

Waste water is a major environmental impediment for the growth of the textile industry besides the other minor issues like solid waste and resource waste management. Textile industry uses many kinds of synthetic dyes and discharge large amounts of highly colored wastewater as the uptake of these dyes by fabrics is very poor. This highly colored textile wastewater severely affects photosynthetic function in plant. It also has an impact on aquatic life due to low light penetration and oxygen consumption. It may also be lethal to certain forms of marine life due to the occurrence of component metals and chlorine present in the synthetic dyes. So, this textile wastewater must be treated before their discharge. In this article, different treatment methods to treat the textile wastewater have been presented along with cost per unit volume of treated water. Treatment methods discussed in this paper involve oxidation methods (cavitation, photocatalytic oxidation, ozone, H2O2, fentons process), physical methods (adsorption and filtration), biological methods (fungi, algae, bacteria, microbial fuel cell). This review article will also recommend the possible remedial measures to treat different types of effluent generated from each textile operation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Bio-ethanol production from wet coffee processing waste in Ethiopia.

PubMed

Woldesenbet, Asrat Gebremariam; Woldeyes, Belay; Chandravanshi, Bhagwan Singh

2016-01-01

Large amounts of coffee residues are generated from coffee processing plants in Ethiopia. These residues are toxic and possess serious environmental problems following the direct discharge into the nearby water bodies which cause serious environmental and health problems. This study was aimed to quantify wet coffee processing waste and estimate its bio-ethanol production. The study showed that the wastes are potential environmental problems and cause water pollution due to high organic component and acidic nature. The waste was hydrolyzed by dilute H 2 SO 4 (0.2, 0.4, 0.6, 0.8 and 1 M) and distilled water. Total sugar content of the sample was determined titrimetrically and refractometry. Maximum value (90%) was obtained from hydrolysis by 0.4 M H 2 SO 4 . Ethanol production was monitored by gas chromatography. The optimum yield of ethanol (78%) was obtained from the sample hydrolyzed by 0.4 M H 2 SO 4 for 1 h at hydrolysis temperature of 100 °C and after fermentation for 24 h and initial pH of 4.5. Based on the data, it was concluded that reuse of the main coffee industry wastes is of significant importance from environmental and economical view points. In conclusion, this study has proposed to utilize the wet coffee processing waste to produce bio-ethanol which provides the alternative energy source from waste biomass and solves the environmental waste disposal as well as human health problem.

Areal studies aid protection of ground-water quality in Illinois, Indiana, and Wisconsin

USGS Publications Warehouse

Mills, Patrick C.; Kay, Robert T.; Brown, Timothy A.; Yeskis, Douglas J.

1999-01-01

In 1991, the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency, initiated studies designed to characterize the ground-water quality and hydrogeology in northern Illinois, and southern and eastern Wisconsin (with a focus on the north-central Illinois cities of Belvidere and Rockford, and the Calumet region of northeastern Illinois and northwestern Indiana). These areas are considered especially susceptible to ground-water contamination because of the high density of industrial and waste-disposal sites and the shallow depth to the unconsolidated sand and gravel aquifers and the fractured, carbonate bedrock aquifers that underlie the areas. The data and conceptual models of ground-water flow and contaminant distribution and movement developed as part of the studies have allowed Federal, State, and local agencies to better manage, protect, and restore the water supplies of the areas. Water-quality, hydrologic, geologic, and geophysical data collected as part of these areal studies indicate that industrial contaminants are present locally in the aquifers underlying the areas. Most of the contaminants, particularly those at concentrations that exceeded regulatory water-quality levels, were detected in the sand and gravel aquifers near industrial or waste-disposal sites. In water from water-supply wells, the contaminants that were present generally were at concentrations below regulatory levels. The organic compounds detected most frequently at concentrations near or above regulatory levels varied by area. Trichloroethene, tetrachloroethene, and 1,1,1-trichloroethane (volatile chlorinated compounds) were most prevalent in north-central Illinois; benzene (a petroleum-related compound) was most prevalent in the Calumet region. Differences in the type of organic compounds that were detected in each area likely reflect differences in the types of industrial sites that predominate in the areas. Nickel and aluminum were the trace metals detected most frequently at concentrations above regulatory levels in both areas. Contaminants in the shallow sand and gravel aquifers and carbonate aquifers appear to have moved with ground water discharging to local lakes, streams, and wetlands. Ground-water flow and possibly contaminant movement is concentrated in the weathered surface zones and in deeper fractures of the carbonate aquifers underlying both areas.

Numerical simulation of filtration of mine water from coal slurry particles

NASA Astrophysics Data System (ADS)

Dyachenko, E. N.; Dyachenko, N. N.

2017-11-01

The discrete element method is applied to model a technology for clarification of industrial waste water containing fine-dispersed solid impurities. The process is analyzed at the level of discrete particles and pores. The effect of filter porosity on the volume fraction of particles has been shown. The degree of clarification of mine water was also calculated depending on the coal slurry particle size, taking into account the adhesion force.

Influence of important factors in industrial debugging of desilication of diaspore by flotation

NASA Astrophysics Data System (ADS)

Ma, Chiyu; Chen, Chen; Hu, Yuehua; Zhu, Hailing; Deng, Haibo

2018-02-01

The beneficiation of diaspore with a low ratio of A/S can be realized by desilication using gradient flotation. The concentrate water can be reused in the flotation process after treating with BXF flocculant. Industrial tests of six months of continuous operation were conducted, and the results show that the concentrate with Al2O3 recovery of 83.04% is obtained, and the ratio of A/S increases from 4.46% in the raw ore to 9.57% in the concentrate. Moreover, the comprehensive reuse rate of the waste-water is 75%.

[Comparative evaluation of health hazards associated with industrial chemicals and their derivates forming during water chlorination].

PubMed

Zholdakova, Z I; Poliakova, E E; Lebedev, A T

2006-01-01

Many industrial chemicals found in waste waters are able to form organochlorine by-products during water disinfection. The transformation of seven model compounds, cyclohexene, n-butanol, diphenylmethane, acetophenone, aniline, 1-methylnaphthalene, and phenylxylylethane during a reaction with active chlorine was studied. Aqueous chlorine and sodium hypochlorite were used as chlorinating agents. The products of the reaction were analyzed by means of chromatomass-spectrometry. A schematic model of diphenylmethane transformation was proposed. Comparative evaluation of hazards associated with the model chemicals and their derivates confirmed that chlorination products can be more toxic and dangerous than the initial compounds, and may possess mutagenic and cancerigenic properties.

Ecology and control of dengue vector mosquitoes in Taiwan.

PubMed

Chen, Y R; Hwang, J S; Guo, Y J

1994-12-01

Due to rapid urbanization, industrialization and social changes in recent years, the use of packing materials and tires has dramatically increased in the Taiwan area. What is more is that some parts of southern Taiwan are short of water resources and water preservation with huge containers becomes part of custom in those areas. Storage water containers, waste vessels and tires are good habitats for Aedes. Meanwhile, some persons traveling to dengue endemic countries bring the dengue disease back to Taiwan. Surveys taken since 1988 show that dengue occurs mainly in the urban and coastal areas where Aedes aegypti is prevalent. This species is the most important, if not the only, vector of dengue in Taiwan. It appears that the types of Aedes breeding have changed quickly. In dengue fever epidemic areas, the most popular breeding sites are ornamental containers (38.8%), storage water containers (30.1%), discarded containers (25.4%), receptacles (3.3%) and water collection in the basement (2.2%). In dengue fever epidemic areas, those building basements, huge water containers, waste vessels and waste tires in open fields are most difficult to clean up and manage and become the most popular Aedes habitats. We established a waste recycling system and promoted a breeding site reduction campaign for waste management, including the application of Temephos in containers to kill larvae. For the drinking water management, fish were released in water containers to prevent larval breeding. It should be mentioned that with the integrated pest control and regular inspections of Aedes larvae in Taiwan the density figures 1, 2-5, and 6 or above for Aedes aegypti were 38.7%, 42.9%, and 18.4%, respectively, in 1988, and in 1993 were 90.8%, 9.2% and 0%. The incidence of dengue fever cases has 98% decreased since 1988. In 1990 and 1993, there was no indigenous cases. We have concluded that integrated pest control is the best and most effective method for dengue fever control, including solid waste and drinking water management.

Applicability of fluidized bed reactor in recalcitrant compound degradation through advanced oxidation processes: a review.

PubMed

Tisa, Farhana; Abdul Raman, Abdul Aziz; Wan Daud, Wan Mohd Ashri

2014-12-15

Treatment of industrial waste water (e.g. textile waste water, phenol waste water, pharmaceutical etc) faces limitation in conventional treatment procedures. Advanced oxidation processes (AOPs) do not suffer from the limits of conventional treatment processes and consequently degrade toxic pollutants more efficiently. Complexity is faced in eradicating the restrictions of AOPs such as sludge formation, toxic intermediates formation and high requirement for oxidants. Increased mass-transfer in AOPs is an alternate solution to this problem. AOPs combined with Fluidized bed reactor (FBR) can be a potential choice compared to fixed bed or moving bed reactor, as AOP catalysts life-span last for only maximum of 5-10 cycles. Hence, FBR-AOPs require lesser operational and maintenance cost by reducing material resources. The time required for AOP can be minimized using FBR and also treatable working volume can be increased. FBR-AOP can process from 1 to 10 L of volume which is 10 times more than simple batch reaction. The mass transfer is higher thus the reaction time is lesser. For having increased mass transfer sludge production can be successfully avoided. The review study suggests that, optimum particle size, catalyst to reactor volume ratio, catalyst diameter and liquid or gas velocity is required for efficient FBR-AOP systems. However, FBR-AOPs are still under lab-scale investigation and for industrial application cost study is needed. Cost of FBR-AOPs highly depends on energy density needed and the mechanism of degradation of the pollutant. The cost of waste water treatment containing azo dyes was found to be US$ 50 to US$ 500 per 1000 gallons where, the cost for treating phenol water was US$ 50 to US$ 800 per 1000 gallons. The analysis for FBR-AOP costs has been found to depend on the targeted pollutant, degradation mechanism (zero order, 1st order and 2nd order) and energy consumptions by the AOPs. Copyright © 2014 Elsevier Ltd. All rights reserved.

Investigations of the unsaturated zone at two radioactive waste disposal sites in Lithuania.

PubMed

Skuratovič, Žana; Mažeika, Jonas; Petrošius, Rimantas; Martma, Tõnu

2016-01-01

The unsaturated zone is an important part of the water cycle, governed by many hydrological and hydrogeological factors and processes and provide water and nutrients to the terrestrial ecosystem. Besides, the soils of the unsaturated zone are regarded as the first natural barrier to a large extent and are able to limit the spread of contaminants depending on their properties. The unsaturated zone provides a linkage between atmospheric moisture, groundwater, and seepage of groundwater to streams, lakes, or other surface water bodies. The major difference between water flow in saturated and unsaturated soils is that the hydraulic conductivity, which is conventionally assumed to be a constant in saturated soils, is a function of the degree of saturation or matrix suction in the unsaturated soils. In Lithuania, low and intermediate level radioactive wastes generated from medicine, industry and research were accumulated at the Maisiagala radioactive waste repository. Short-lived low and intermediate levels radioactive waste, generated during the operation of the Ignalina Nuclear Power Plant (INPP) and arising after the INPP decommissioning will be disposed of in the near surface repository close to the INPP (Stabatiske site). Extensive data sets of the hydraulic properties and water content attributed to unsaturated zone soil profiles of the two radioactive waste disposal sites have been collected and summarized. Globally widespread radionuclide tritium ((3)H) and stable isotope ratio ((18)O/(16)O and (2)H/(1)H) distribution features were determined in precipitation, unsaturated zone soil moisture profiles and groundwater.

Water Quality Assessment of River Soan (Pakistan) and Source Apportionment of Pollution Sources Through Receptor Modeling.

PubMed

Nazeer, Summya; Ali, Zeshan; Malik, Riffat Naseem

2016-07-01

The present study was designed to determine the spatiotemporal patterns in water quality of River Soan using multivariate statistics. A total of 26 sites were surveyed along River Soan and its associated tributaries during pre- and post-monsoon seasons in 2008. Hierarchical agglomerative cluster analysis (HACA) classified sampling sites into three groups according to their degree of pollution, which ranged from least to high degradation of water quality. Discriminant function analysis (DFA) revealed that alkalinity, orthophosphates, nitrates, ammonia, salinity, and Cd were variables that significantly discriminate among three groups identified by HACA. Temporal trends as identified through DFA revealed that COD, DO, pH, Cu, Cd, and Cr could be attributed for major seasonal variations in water quality. PCA/FA identified six factors as potential sources of pollution of River Soan. Absolute principal component scores using multiple regression method (APCS-MLR) further explained the percent contribution from each source. Heavy metals were largely added through industrial activities (28 %) and sewage waste (28 %), nutrients through agriculture runoff (35 %) and sewage waste (28 %), organic pollution through sewage waste (27 %) and urban runoff (17 %) and macroelements through urban runoff (39 %), and mineralization and sewage waste (30 %). The present study showed that anthropogenic activities are the major source of variations in River Soan. In order to address the water quality issues, implementation of effective waste management measures are needed.

Agronomic assessment of pyrolysed food waste digestate for sandy soil management.

PubMed

Opatokun, Suraj Adebayo; Yousef, Lina F; Strezov, Vladimir

2017-02-01

The digestate (DFW) of an industrial food waste treatment plant was pyrolysed for production of biochar for its direct application as bio-fertilizer or soil enhancer. Nutrient dynamics and agronomic viability of the pyrolysed food waste digestate (PyD) produced at different temperatures were evaluated using germination index (GI), water retention/availability and mineral sorption as indicators when applied on arid soil. The pyrolysis was found to enrich P, K and other micronutrients in the biochar at an average enrichment factor of 0.87. All PyD produced at different temperatures indicated significantly low phytotoxicity with GI range of 106-168% and an average water retention capacity of 40.2%. Differential thermogravimetric (DTG) thermographs delineated the stability of the food waste digestate pyrolysed at 500 °C (PyD500) against the degradation of the digestate food waste despite the latter poor nutrient sorption potential. Plant available water in soil is 40% when treated with 100 g of digestate per kg soil, whereas PyD500 treated soil indicated minimal effect on plant available water, even with high application rates. However, the positive effects of PyD on GI and the observed enrichment in plant macro and micronutrients suggest potential agronomic benefits for PyD use, in addition to the benefits from energy production from DFW during the pyrolysis process. Copyright © 2016 Elsevier Ltd. All rights reserved.

Presence of Epsilon HCH Together with Four Other HCH Isomers in Drinking Water, Groundwater and Soil in a Former Lindane Production Site.

PubMed

Fuscoletti, Valentina; Achene, Laura; Gismondi, Fabrizio; Lamarra, Daniela; Lucentini, Luca; Spina, Salvatore; Veschetti, Enrico; Turrio-Baldassarri, Luigi

2015-07-01

In the frame of a long-standing action of remediation of industrial soil and prevention of water pollution, a monitoring of the drinking water of the Italian town of Colleferro was performed by the ISS. The town has 22,000 inhabitants and is adjacent to a big industrial site where HCH was produced. Industrial wastes were buried in the site, eventually contaminating superficial aquifers, while a canal serving the industrial plant spread the contamination into the Sacco river and thence to the agricultural soil and to cow milk. The contamination of superficial aquifers engendered fears of pollution of the deep aquifers whence the town draws its drinking water. The results of the monitoring indicate that there is no risk for the population from consumption of the water. In one of the wells the ε-HCH was the main isomer reaching a concentration of 66 ng/L: so far the presence of this isomer in water was never reported. The paper also summarily reports the main features of soil and superficial groundwater pollution in the area and briefly describes the main actions taken by the authorities.

Reuse of ornamental rock-cutting waste in aluminous porcelain.

PubMed

Silva, M A; Paes, H R; Holanda, J N F

2011-03-01

Large amounts of solid wastes are discarded in the ornamental rocks industry. This work investigates the incorporation of ornamental rock-cutting waste as a raw material into an aluminous porcelain body, replacing natural feldspar material by up to 35 wt.%. Formulations containing rock-cutting waste were pressed and sintered at 1350 °C. The porcelain pieces were tested to determine their properties (linear shrinkage, water absorption, apparent density, mechanical strength, and electrical resistivity). Development of the microstructure was followed by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses. The results showed that ornamental rock-cutting waste could be used in aluminous porcelains, in the range up to 10 wt.%, as a partial replacement for traditional flux material, resulting in a valid route for management of this abundant waste. Copyright © 2010 Elsevier Ltd. All rights reserved.

Separation and collection of coarse aggregate from waste concrete by electric pulsed power

NASA Astrophysics Data System (ADS)

Shigeishi, Mitsuhiro

2017-09-01

Waste concrete accounts for a substantial fraction of construction waste, and the recycling of waste concrete as concrete aggregate for construction is an important challenge associated with the rapid increase in the amount of waste concrete and the tight supply of natural aggregate. In this study, we propose a technique based on the use of high-voltage pulsed electric discharge into concrete underwater for separating and collecting aggregate from waste concrete with minimal deterioration of quality. By using this technique, the quality of the coarse aggregate separated and collected from concrete test specimens is comparable to that of coarse aggregate recycled by heating and grinding methods, thus satisfying the criteria in Japan Industrial Standard (JIS) A 5021 for the oven-dry density and the water absorption of coarse aggregate by advanced recycling.

Valorisation of blueberry waste and use of compression to manufacture sustainable starch films with enhanced properties.

PubMed

Luchese, Cláudia Leites; Uranga, Jone; Spada, Jordana Corralo; Tessaro, Isabel Cristina; de la Caba, Koro

2018-08-01

Blueberry waste from juice processing was valorised to develop starch films by compression moulding. The compression process resulted in hydrophobic films with water contact angles even higher than 100° for the films prepared with the highest blueberry waste content. Additionally, the film solubility was reduced by the incorporation of blueberry waste, regardless of the solution pH. These films also exhibited good barrier properties against UV light due to the aromatic compounds present in the blueberry waste. Furthermore, films showed a homogenous surface, although some pores appeared in the cross-section for the films with the highest blueberry waste content. Results highlighted the use of thermo-mechanical processes such as compression to manufacture sustainable films with enhanced properties through waste valorisation by the techniques actually employed at industrial scale. Copyright © 2018 Elsevier B.V. All rights reserved.

Health assessment for Lake Sandy Jo Landfill, Gary, Indiana, Region 5. CERCLIS No. IND980500524. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1985-11-21

The 50-acre Lake Sandy Jo Landfill is located in the Black Oak community (predominantly residential) of southwestern Gary in Lake County, Indiana. From about 1971 until about 1980, the lake was filled in with construction and demolition debris, municipal garbage, industrial wastes, hazardous materials, and possibly drummed wastes. These wastes are partly to completely exposed on the landfill surface. Surface soil, subsurface soil, surface water, sediment, and ground water show a variety of metal and organic chemical carcinogens. Toxic noncarcinogen priority pollutants found were chloromethane, copper, cyanide, lead, mercury, and silver. Inorganic soil levels found on the site for leadmore » and cadmium exceed levels of concern that would permit unrestricted use of the site. Remedial measures would be necessary before the site could be granted unrestricted use.« less

Hydrologic monitoring of a waste-injection well near Milton, Florida, June 1975 - December 1976

USGS Publications Warehouse

Pascale, Charles A.; Martin, J.B.

1977-01-01

Hydraulic and chemical data were collected through a monitoring program conducted by the U.S. Geological Survey at an industrial liquid-waste injection site 6 mi southwest of Milton, Fla., in Santa Rosa County. The injection system is described. Data include injection rates, volumes, and pressures; water-level data at three monitor wells and a standby injection well, and field and laboratory analyses of water samples from four wells. Hydraulic and geochemical effects of the waste-injection system at the plant as of December 31, 1976, have been detected only in the injection zone, the lower limestone of the Floridan aquifer. Increased pressures are evident at the three wells used to monitor the injection zone. Geochemical changes have been noted only at the deep-test monitor well closest to the injection well. (Woodard-USGS)

Globally sustainable manganese metal production and use.

PubMed

Hagelstein, Karen

2009-09-01

The "cradle to grave" concept of managing chemicals and wastes has been a descriptive analogy of proper environmental stewardship since the 1970s. The concept incorporates environmentally sustainable product choices-such as metal alloys utilized steel products which civilization is dependent upon. Manganese consumption is related to the increasing production of raw steel and upgrading ferroalloys. Nonferrous applications of manganese include production of dry-cell batteries, plant fertilizer components, animal feed and colorant for bricks. The manganese ore (high grade 35% manganese) production world wide is about 6 million ton/year and electrolytic manganese metal demand is about 0.7 million ton/year. The total manganese demand is consumed globally by industries including construction (23%), machinery (14%), and transportation (11%). Manganese is recycled within scrap of iron and steel, a small amount is recycled within aluminum used beverage cans. Recycling rate is 37% and efficiency is estimated as 53% [Roskill Metals and Minerals Reports, January 13, 2005. Manganese Report: rapid rise in output caused by Chinese crude steel production. Available from: http://www.roskill.com/reports/manganese.]. Environmentally sustainable management choices include identifying raw material chemistry, utilizing clean production processes, minimizing waste generation, recycling materials, controlling occupational exposures, and collecting representative environmental data. This paper will discuss two electrolytically produced manganese metals, the metal production differences, and environmental impacts cited to date. The two electrolytic manganese processes differ due to the addition of sulfur dioxide or selenium dioxide. Adverse environmental impacts due to use of selenium dioxide methodology include increased water consumption and order of magnitude greater solid waste generation per ton of metal processed. The use of high grade manganese ores in the electrolytic process also reduces the quantity of solid wastes generated during processing. Secondary aluminum facilities have reported hazardous waste generation management issues due to baghouse dusts from rotary furnaces processing selenium contaminated manganese alloys. Environmental impacts resulting from industry are represented by emission inventories of chemical releases to the air, water, and soil. The U.S. metals industry releases reported to EPA Toxic Release Inventory indicate the primary metals industry is the major source of metal air toxic emissions, exceeding electric utility air toxic emissions. The nonferrous metals industry is reported to be the Organization for Economic Co-operation and Development (OECD) most intensive airborne and land pollution source of bioaccumulative metals. However, total waste emissions from industries in the OECD countries have declined due to improving energy consumption. Emission registers and access are improving around the world. However, environmental databases for metal particulates have low confidence ratings since the majority of air toxic emissions are not reported, not monitored, or are estimated based on worst-case emission factors. Environmental assessments including biological monitoring are necessary to validate mandated particulate metal emission reductions and control technologies during metal processing.

A preliminary evaluation of the geohydrology and water quality of the Greenacres Landfill area, Spokane County, Washington

USGS Publications Warehouse

Lum, W. E.; Turney, G.L.; Alvord, R.C.

1986-01-01

The Greenacres Landfill, located about 11 mi east of the city of Spokane, Washington, was used for the disposal of waste from 1951 to 1972. Materials in the landfill include household and industrial waste materials, and various hazardous wastes. In 1983 the landfill was designated by the U.S. EPA as a ' Superfund ' site. The purposes of this investigation were to gather, describe, and interpret all the existing data concerning the hydrology and groundwater quality of the area surrounding the landfill, and to identify any additional data needed to describe the hydrology of the area. The quantity of water flow through the landfill as a result of precipitation on the landfill and in the drainage basin above the landfill probably ranges from 21,000 to 85,000 gal/day. This water movement may be creating a leachate and transporting some of the wastes out of the landfill. The plume would encompass an area where groundwater provides most of the water used for municipal, industrial, irrigation, and domestic purposes. Water quality analyses of water from numerous wells in the area which are open to the Spokane aquifer are available, but well 25/45-16K1 is the only well where groundwater contamination was consistently apparent. This well is only 500 ft from the landfill. Contamination of water in this well was indicated by high concentrations of dissolved mineral constituents and several organic compounds, including trans-dichloroethene (115 to 392 micrograms/L). Available data are insufficient to completely interpret the groundwater flow system near this well and the source of the contamination cannot be determined conclusively. While the existing data are adequate to provide background information, more data are needed to: (1) determine the source of contamination in well 25/45-16K1; (2) determine groundwater flow in the Spokane aquifer near well 25/45-16K1; and (3) determine the extent of contamination in the Spokane aquifer. The degree of the influence of the landfill on the Spokane aquifer cannot be determined with existing data. (Author 's abstract)

Health assessment for Midwest Industrial Waste Disposal Company, Inc. (Midco II) NPL (National Priorities List) Site, 5900 Industrial Highway, Gary, Indiana, Region 5. CERCLIS No. IND980679559. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-04-12

The 7-acre Midco II Site is located at 5900 Industrial Highway, Gary, Indiana. The site is listed on the National Priorities List. Various heavy metals, inorganic, and organic compounds were found in the media on-site. The environmental media of concern at the site are ground water, surface water, and soil. Although access to the Midco II site is restricted, the contaminants detected on-site will continue to migrate and may pose health threats until remedial activities are completed. Therefore, the Midco II site poses a potential health concern until an evaluation of the site is completed and remedial activities are chosen.

Highly porous carbon from a natural cellulose fiber as high efficiency sorbent for lead in waste water.

PubMed

Ilangovan, Manikandan; Guna, Vijaykumar; Olivera, Sharon; Ravi, Ashwini; Muralidhara, H B; Santosh, M S; Reddy, Narendra

2017-12-01

The persistence of hollow centre in the carbon obtained from milkweed floss provides exceptional sorption characteristics, not seen in common biomasses or their derivatives. A considerably high sorption of 320mg of lead per gram of milkweed carbon was achieved without any chemical modification to the biomass. In this research, we have carbonized milkweed floss and used the carbon as a sorbent for lead in waste water. A high surface area of 170m 2 g -1 and pore volume of 1.07cm 3 g -1 was seen in the carbon. Almost complete removal (>99% efficiency) of lead could be achieved within 5min when the concentration of lead in the solution was 100ppm, close to that prevailing in industrial waste water. SEM images showed that the carbon was hollow and confocal images confirmed that the sorbate could penetrate inside the hollow tube. Copyright © 2017 Elsevier Ltd. All rights reserved.

Geothermal Produced Fluids: Characteristics, Treatment Technologies, and Management Options

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finster, Molly; Clark, Corrie; Schroeder, Jenna

2015-10-01

Geothermal power plants use geothermal fluids as a resource and create waste residuals as part of the power generation process. Both the geofluid resource and the waste stream are considered produced fluids. The chemical and physical nature of produced fluids can have a major impact on the geothermal power industry and can influence the feasibility of geothermal power development, exploration approaches, power plant design, operating practices, and the reuse or disposal of residuals. In general, produced fluids include anything that comes out of a geothermal field and that subsequently must be managed on the surface. These fluids vary greatly dependingmore » on the geothermal reservoir being harnessed, power plant design, and the life cycle stage in which the fluid exists, but generally include water and fluids used to drill geothermal wells, fluids used to stimulate wells in enhanced geothermal systems, and makeup and/or cooling water used during operation of a geothermal power plant. Additional geothermal-related produced fluids include many substances that are similar to waste streams from the oil and gas industry, such as scale, flash tank solids, precipitated solids from brine treatment, hydrogen sulfide, and cooling-tower-related waste. This review paper aims to provide baseline knowledge on specific technologies and technology areas associated with geothermal power production. Specifically, this research focused on the management techniques related to fluids produced and used during the operational stage of a geothermal power plant; the vast majority of which are employed in the generation of electricity. The general characteristics of produced fluids are discussed. Constituents of interest that tend to drive the selection of treatment technologies are described, including total dissolved solids, noncondensable gases, scale and corrosion, silicon dioxide, metal sulfides, calcium carbonate, corrosion, metals, and naturally occurring radioactive material. Management options for produced fluids that require additional treatment for these constituents are also discussed, including surface disposal, reuse and recycle, agricultural industrial and domestic uses, mineral extraction and recovery, and solid waste handling.« less

Creation of Emergent Sandbar Habitat (ESH) in the Headwaters of Lewis and Clark Lake and the Impacts on Water Quality

DTIC Science & Technology

2009-04-01

probably tich in decayed vegetative matter (i.e., humus ) and seed stock. The richness of the matetial is indicated by its ctru·ker color as shown in...iron and manganese), humus and peat materials, plankton, weeds, and industrial wastes (APHA, 1998). “True color” is the color of water from which

Industrial-waste management in developing countries: the case of Lebanon.

PubMed

el-Fadel, M; Zeinati, M; el-Jisr, K; Jamali, D

2001-04-01

This paper presents a critical assessment of the existing Lebanese industrial sector, namely the current status and classification of industrial establishments based on a comparative synthesis and analysis of recent nationwide surveys and studies pertaining to industrial-waste management. Characterisation of solid and liquid industrial wastes generated, including hazardous wastes, is presented together with current and projected waste loads, recycling opportunities, and export/import practices. Institutional capacity and needs pertaining to the enforcement of relevant environmental legislation, staffing and resources, monitoring schemes, and public participation are critically evaluated. Finally, realistic options for industrial-waste management in the context of country-specific institutional economic and technical limitations are outlined. The industrial sector in Lebanon consists of small-scale industries (84% employ less than 10 persons), primarily involved in light manufacturing (96%). These industries which are distributed among 41 ill-defined zones and deficient in appropriate physical infrastructure, generate solid, liquid, and hazardous waste estimated at 346,730 tons/year, 20,169,600 m3/year and between 3000 to 15,000 tons/year, respectively. Although the growth of this sector contributes significantly to the socio-economic development of the country (industry accounts for 17% of the gross domestic product), in the absence of a comprehensive environmental management plan, this expansion may not be sustained into the coming millennium. The anticipated expansion will inevitably amplify adverse environmental impacts associated with industrial activities due to rising waste volumes and improper waste handling and disposal practices. These impacts are further aggravated by a deficient institutional framework, a lack of adequate environmental laws, and lax enforcement of regulations governing industrial-waste management.

Assessment of anthropogenic inputs in the surface waters of the southern coastal area of Sfax during spring (Tunisia, Southern Mediterranean Sea).

PubMed

Drira, Zaher; Kmiha-Megdiche, Salma; Sahnoun, Houda; Hammami, Ahmed; Allouche, Noureddine; Tedetti, Marc; Ayadi, Habib

2016-03-15

The coastal marine area of Sfax (Tunisia), which is well-known for its high productivity and fisheries, is also subjected to anthropogenic inputs from diverse industrial, urban and agriculture activities. We investigated the spatial distribution of physical, chemical and biogeochemical parameters in the surface waters of the southern coastal area of Sfax. Pertinent tracers of anthropogenic inputs were identified. Twenty stations were sampled during March 2013 in the vicinity of the coastal areas reserved for waste discharge. Phosphogypsum wastes dumped close to the beaches were the main source of PO4(3-), Cl(-) and SO4(2-) in seawater. The high content in total polyphenolic compounds was due to the olive oil treatment waste water released from margins. These inorganic and organic inputs in the surface waters were associated with elevated COD. The BOD5/COD (<0.5) and COD/BOD5 (>3) ratios highlighted a chemical pollution with organic load of a low biodegradability. Copyright © 2016 Elsevier Ltd. All rights reserved.

Methane gas generation from waste water extraction process of crude palm oil in experimental digesters

NASA Astrophysics Data System (ADS)

Dillon, A.; Penafiel, R.; Garzón, P. V.; Ochoa, V.

2015-12-01

Industrial processes to extract crude palm oil, generates large amounts of waste water. High concentrations of COD, ST, SV, NH4 + and low solubility of O2, make the treatment of these effluents starts with anaerobic processes. The anaerobic digestion process has several advantages over aerobic degradation: lower operating costs (not aeration), low sludge production, methane gas generation. The 4 stages of anaerobic digestion are: hydrolysis, acidogenic, acetogenesis and methanogenesis. Through the action of enzymes synthesized by microbial consortia are met. The products of each step to serve as reagents is conducted as follows. The organic load times and cell hydraulic retention, solids content, nutrient availability, pH and temperature are factors that influence directly in biodigesters. The objectives of this presentation is to; characterize the microbial inoculum and water (from palm oil wasted water) to be used in biodigestores, make specific methanogenic activity in bioassays, acclimatize the microorganisms to produce methane gas using basal mineral medium with acetate for the input power, and to determine the production of methane gas digesters high organic load.

2016 Annual Industrial Wastewater Reuse Report for the Idaho National Laboratory Site’s Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cafferty, Kara Grace

This report describes conditions, as required by the state of Idaho Industrial Wastewater Reuse Permit (WRU-I-0160-01, Modification 1, formerly LA 000160 01), for the wastewater reuse site at the Idaho National Laboratory Site’s Materials and Fuels Complex Industrial Waste Ditch and Industrial Waste Pond from November 1, 2015, through October 31, 2016.

Impacts of geothermal energy developments on hydrological environment in hot spring areas

NASA Astrophysics Data System (ADS)

Taniguchi, M.

2015-12-01

Water-energy nexus such as geothermal energy developments and its impacts on groundwater, river water, and coastal water is one of the key issues for the sustainable society. This is because the demand of both water and energy resources will be increasing in near future, and the tradeoff between both resources and conflict between stakeholders will be arisen. Geothermal power generation, hot springs heat power generation, and steam power generation, are developing in hot spring areas in Ring of Fire countries including Japan, as renewable and sustainable energy. Impacts of the wasted hot water after using hot springs heat and steam power generation on ecosystem in the rivers have been observed in Beppu, Oita prefecture, Japan. The number of the fish species with wasted hot water in the Hirata river is much less than that without wasted hot water in Hiyakawa river although the dominant species of tilapia was found in the Hirata river with wasted hot water. The water temperature in Hirata rive is increased by wasted hot water by 10 degree C. The impacts of the developments of steam power generations on hot spring water and groundwater in downstream are also evaluated in Beppu. The decreases in temperature and volume of the hot spring water and groundwater after the development are concerning. Stakeholder analysis related to hot spa and power generation business and others in Beppu showed common interests in community development among stakeholders and gaps in prerequisite knowledge and recognition of the geothermal resource in terms of economic/non-economic value and utilization as power generation/hot-spring. We screened stakeholders of four categories (hot spring resorts inhabitants, industries, supporters, environmentalists), and set up three communities consisting of 50 persons of the above categories. One remarkable result regarding the pros and cons of geothermal power in general terms was that the supporter count increased greatly while the neutralities count decreased greatly after deliberation, suggesting a response from providing scientific evidence on the issue.

Properties of palm oil fuel ash cement sand brick containing pulverized cockle shell as partial sand replacement

NASA Astrophysics Data System (ADS)

Mat Aris, S.; Muthusamy, K.; Uzer, A.; Ahmad, S. Wan

2018-04-01

Environmental pollution caused by the disposal of solid wastes generated from both palm oil industry and cockle shell trade has motivated researches to explore the potential of these wastes. Integrating these wastes in production of construction material is one of the ways to reduce amount of waste thrown at dumping area. Thus, the present investigation investigates the performance of palm oil fuel ash (POFA) cement sand brick containing pulverized cockle shell as partial fine aggregate replacement. All mixes used contain 20% of POFA as partial cement replacement. Total of six mixes were prepared by adding a range of pulverized cockle shell that is 0%, 10%, 20%, 30%, 40% and 50% as partial sand replacement. The mixes were prepared in form of brick. All the water cured samples were tested for compressive strength and flexural strength until 28 days. Findings show that brick produced using 20% pulverized cockle shell exhibit the highest compressive strength and flexural strength also the lowest water absorption value.

Sanitary engineering aspects of nuclear energy developments*

PubMed Central

Kenny, A. W.

1962-01-01

So many developments have taken place in the field of nuclear energy since 1956, when the author's previous paper on radioactive waste disposal was published in the Bulletin of the World Health Organization, that a fresh review of the subject is now appropriate. The present paper deals with those aspects of the problem which are of most interest to the sanitary engineer. It considers specific points in the latest recommendations of the International Commission on Radiological Protection in relation to public drinking-water supplies, and examines the problem of fall-out, with special reference to the presence and significance of strontium-90 in drinking-water. A general survey of the various uses of radioactive materials is followed by a discussion of the legislative and control measures necessary to ensure safe disposal of wastes. The methods of waste disposal adopted in a number of nuclear energy establishments are described in detail. The paper concludes with some remarks on solid waste disposal, siting of nuclear energy industries and area monitoring. PMID:14455214

Solid anaerobic digestion: State-of-art, scientific and technological hurdles.

PubMed

André, Laura; Pauss, André; Ribeiro, Thierry

2018-01-01

In this paper, a state-of-art about solid anaerobic digestion (AD), focused on recent progress and trends of research is proposed. Solid anaerobic digestion should be the most appropriate process for degradation of by-products with high total solid (TS) content, especially lignocellulosic materials like agricultural waste (straw, manure), household waste and food waste. Solid AD is already widely used in waste water treatment plant for treating plant for sewage sludge but could be more developed for lignocellulosic materials with high TS content. Many research works were carried out in Europe on solid AD, focused on current hurdles (BMP, codigestion, inhibition, microbial population, rheology, water transfers, inoculum, etc.) in order to optimize the solid AD process. In conclusion, hurdles of solid AD process should and must be solved in order to propose better productivity and profitability of such system operating with high TS content (>15%), favouring reliable industrial processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of bio based plastic materials for packaging from soybeans waste

NASA Astrophysics Data System (ADS)

Muhammad, A.; Rashidi, A. R.; Roslan, A.; Idris, S. A.

2017-09-01

Demands of plastic material which increase with the increasing of human population encourage researchers to find alternative solution to replace petro based plastic. Thus, in the present study, a novel "green bioplastic" packaging was developed using soybean waste which is a major waste in soy sauce food industry. The evaluation of the effect of ratio of starch, soy waste and plasticizer in this bioplastic production was studied and their characteristics were compared with available bioplastics. Characteristics study was done in terms of burning test, water absorption capacity, thermal and tensile strength measurement and the result obtained were analyzed. The glass transition temperature (Tg) for soy waste bioplastic is 117˚C. The water absorption test shows that an increase in mass up to 114.17% which show large amount of water uptake capacity of this bioplastics. And about 38% of percentage loss was observed when compared with other novel bioplastics. The results clearly show that the amount of glycerol as a plasticizer had an inversely proportional relationship with the Glass Transition Temperature (Tg). The average maximum force value for tensile strength test is 6.71 N. The burning test show that the soy wastes bioplastic release a very faint smell of soy and glue-like substance. The flame ignited a Yellowish-Orange colour and released some sparks. Based on the overall results, soy-based have been proven to become an excellent bio-based packaging materials.

Pollution and sanitation problems as setbacks to sustainable water resources management in Freetown.

PubMed

Kallon, Senesie B

2008-12-01

The civil conflict in Sierra Leone (1991-2001) caused a dramatic increase in the population of Freetown. This population increase overstretched housing facilities, leading to the creation of camps and many squatter settlements with poor sanitation practices. Overcrowding has become a serious concern in light of the acute water shortage that struck Freetown in May and June 2006. Some of the numerous small water bodies that could have been used to augment the public water supply were contaminated by the disposal of solid and industrial waste and poor sewage management. Improper disposal practices have a direct impact on public health. This paper recommends addressing the policy gap, establishing clear threshold criteria for all water bodies and wastewater discharge, and integrating the above issues in the ongoing review process of draft water sanitation policy. Public education of the negative consequences of poor waste management practices on water quality and public health can also positively affect general sanitation practices

An Analysis of Coastal Zone Management Program Proposals to Determine their Effect on the United States Air Force.

DTIC Science & Technology

1976-06-01

control legislation, including water, air, sewage treatment, and noise, (3) restriction on land use, 10 11. water use, and master planning, (4...into enclosed bays and estuaries. Sewage systems will be upgraded to meet Federa~l standards. New developments will not be connected into substandard... sewage systems. The reuse of adequately treated waste water for agricultural, industrial or domestic facilities is encouraged. Intake’seawater and

Getting proficient in RAS fundamentals - TCFFI trains aquaculture facility owners, operators and designers

USDA-ARS?s Scientific Manuscript database

Many federal, state, and tribal aquaculture programs are adopting water recirculation technologies as a means to maintaining and/or expanding their level of fish production, while reducing the environmental impact of waste dissemination. Similarly, the North American commercial aquaculture industry ...

POTENTIAL INDICATORS FOR THE ASSESSMENT OF ARSENIC NATURAL ATTENUATION IN THE SUBSURFACE

EPA Science Inventory

Arsenic is a priority pollutant found in soil and ground water contaminated by arsenic pesticides and industrial wastes. Assessing the natural attenuation capacity of the subsurface for arsenic is a key step leading to successful site remediation. Chemical reactions between arsen...

A new procedure for treatment of oily slurry using geotextile filters.

PubMed

Mendonça, M B; Cammarota, M C; Freire, D D C; Ehrlich, M

2004-07-05

A new procedure to mitigate the environmental impacts and reduce the cost of disposal of oil slurry is present in this paper. Waste from the petroleum industry has a high environmental impact. Systems for oil-water separation have been used to mitigate the contamination potential of these types of effluents. At the outlet of these systems, the oil is skimmed-off the surface, while the slurry is removed from the base. Due to the high concentration of contaminants, the disposal of this slurry is an environmentally hazardous practice. Usually this type of waste is disposed of in tanks or landfills after removal from the industrial plant. Basically, the proposed procedure utilizes drying beds with geotextile filters to both reduce the water content in the slurry and obtain a less contaminated effluent. Laboratory tests were carried out to simulate the drying system. Four types of filters were analyzed: two non-woven geotextiles, one woven geotextile, and a sand filter.

Nalco Fuel Tech

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michalak, S.

1995-12-31

The Nalco Fuel Tech with its seat at Naperville (near Chicago), Illinois, is an engineering company working in the field of technology and equipment for environmental protection. A major portion of NALCO products constitute chemical materials and additives used in environmental protection technologies (waste-water treatment plants, water treatment, fuel modifiers, etc.). Basing in part on the experience, laboratories and RD potential of the mother company, the Nalco Fuel Tech Company developed and implemented in the power industry a series of technologies aimed at the reduction of environment-polluting products of fuel combustion. The engineering solution of Nalco Fuel Tech belong tomore » a new generation of environmental protection techniques developed in the USA. They consist in actions focused on the sources of pollutants, i.e., in upgrading the combustion chambers of power engineering plants, e.g., boilers or communal and/or industrial waste combustion units. The Nalco Fuel Tech development and research group cooperates with leading US investigation and research institutes.« less

Arsenic detection in water: YPO{sub 4}:Eu{sup 3+} nanoparticles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghosh, Debasish; Luwang, Meitram Niraj, E-mail: mn.luwang@ncl.res.in; Academy of Scientific and Innovative Research

This work reports on the novel technique of detection of arsenic in aqueous solution utilising the luminescence properties of lanthanide doped nanomaterials. Eu{sup 3+} (5%) doped YPO{sub 4}nanorodswere utilised for the said experiment. Co-precipitation method was used for the synthesis of the materials and characterised them with different instrumental techniques like X-ray diffraction (XRD), Infra-red (IR), UV-absorption, scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS) and photoluminescence studies. This nanoparticle can adsorb both arsenic and arsenious acids. We studied the effect of arsenic adsorption on the luminescence behaviour of the nanoparticles. Arsenic acid enhanced the luminescencemore » intensity whereas arsenious acid quenched the luminescence. This luminescence enhancement or quenching is related with arsenic concentration. This relation of luminescence property with concentration of arsenic can be used to detect arsenic in industrial waste. - Graphical abstract: Novel technique of detection of Arsenic ion in aqueous solution utilising the luminescence properties of lanthanide doped nanomaterials. Potential application for detection of arsenic in drinking and industrial waste water. - Highlights: • Novel technique of detection of Arsenic in aqueous solution by YPO{sub 4}:Eu{sup 3+} nanomaterials. • The effect of arsenic adsorption on the luminescence behaviour of the nanoparticles was studied. • Arsenic acid enhance whereas arsenious acid quenches the luminescence intensity. • This technique can be used to detect arsenic in industrial waste.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirk, D.W.

The generation of industrial solid wastes containing leachable species of environmental concern is a problem for developing and developed nations alike. These materials arise from direct processing of mineral ores, from production of metals and minerals, from manufacturing operations, and from air and water pollution treatment processes. The general characteristics that make these wastes intractable is that their content of hazardous species is not easily liberated from the waste yet is not bound so tightly that they are safe for landfill disposal or industrial use. The approach taken in this work is a thermal treatment that separates the inorganic contaminantsmore » from the wastes. The objective is to provide recovery and reuse of both the residual solids and liberated contaminants. The results from operating this technique using two very different types of waste are described. The reasons that the process will work for a wide variety of wastes are explored. By using the knowledge of the thermodynamic stability of the phases found from the characterization analyses, a thermal regime was found that allowed separation of the contaminants without capturing the matrix materials. Bench scale studies were carried out using a tube furnace. Samples of the wastes were heated in crucible boats from 750 to 1150{degrees}C in the presence of various chlorinating agents. The offgas contained 90{sup +}% of the targeted contaminants despite their complex matrix form. The residue was free of contamination. As a result of the efficient concentrating mechanism of the process, the contaminants in the offgas solids are attractive for reuse in metallurgical industries. As an additional benefit, the organic contaminants of the residues were eliminated. Dioxin traces in the solids before treatment were absent after treatment. 15 refs., 4 figs., 4 tabs.« less

Mobilization and transport of pollutants in an abandoned dump in tropical conditions

NASA Astrophysics Data System (ADS)

Pelinson, Natalia; Shinzato, Marjolly; Wendland, Edson

2017-04-01

The valuation and treatment techniques of municipal solid waste (MSW) in developing countries are not sufficiently developed, and therefore, the volume of waste destined for disposal still presents significant amounts. In Brazil, the more common practice of final destination is the deposition on the soil, due to its simple operation and low cost compared to other techniques. One of the most serious negative environmental impacts in the irregular disposal of solid waste is the contamination of soil and groundwater by waste leachates. The final disposal in dumps is forbidden by Brazilian law since 2010, nevertheless, the public administration is not prepared to monitor waste disposal areas and the risk of contamination of water. In this sense, a research has been developed in an abandoned dump installed over an outcrop of the Botucatu Formation, which is part of the Guarani Aquifer System (SAG) and therefore, is an area of high water vulnerability. In this dump, an old gully was used as a final waste disposal area for urban, construction and demolition, medical and industrial waste from 1980 to 1996. Since the end of the deposition, the waste body is kept with inefficient hydraulic control. The water infiltration due to rainfall promotes the mobility of contaminant in the deposit. The present water quality in the dump has been monitored through physical and chemical analysis of samples collected in the unsaturated zone (inside the waste mass using vacuum lysimeters) and in the saturated zone (monitoring wells). The rainfall variation observed in the years 2014 (dry year) and 2015 (wet year) contributed significantly to evaluate the mobilization of pollutants within the dump. The reduction of the water volume that infiltrates the waste mass affected the quality of the leachate collected in the lysimeters. The groundwater collected in monitoring wells outside the dump area presents low turbidity values (<1.50 NTU) in relation to wells located downstream of the dump showed values greater than 10, a similar behavior was observed for the conductivity (>1000 µS.cma-1 in leachate) and chlorides values (>800 mg.L-1). Contaminated water flows through the bottom of the dump. In addition, this research also indicates amendments of surface water downstream of the dump area.

Nutrient recycling of lipid-extracted waste in the production of an oleaginous thraustochytrid.

PubMed

Lowrey, Joshua; Brooks, Marianne S; Armenta, Roberto E

2016-05-01

Improving the economics of microalgae production for the recovery of microbial oil requires a comprehensive exploration of the measures needed to improve productivity as well as to reduce the overall processing costs. One avenue for cost reduction involves recycling the effluent waste water remaining after lipid extraction. This study investigates the feasibility of recycling those wastes for growing thraustochytrid biomass, a heterotrophic microalgae, where wastes were generated from the enzymatic extraction of the lipids from the cell biomass. It was demonstrated that secondary cultures of the tested thraustochytrid grown in the recycled wastes performed favorably in terms of cell and oil production (20.48 g cells L(-1) and 40.9 % (w/w) lipid) compared to the control (13.63 g cells L(-1) and 56.8 % (w/w) lipid). Further, the significant uptake of solubilized cell material (in the form of amino acids) demonstrated that the recycled waste has the potential for offsetting the need for fresh medium components. These results indicate that the implementation of a nutrient recycling strategy for industrial microalgae production could be possible, with significant added benefits such as conserving water resources, improving production efficiency, and decreasing material inputs.

Wind erosion of waste impoundments in arid climates and mitigation of dust pollution.

PubMed

Blight, G E

2008-12-01

Wind can erode and disperse fine-grained material from an impoundment of mining, industrial or municipal waste that stands above the level of its surroundings. Such dust dispersion can be a serious nuisance as well as a health hazard to inhabitants and animals in nearby settlements. It can also degrade crops, making them less marketable, and pollute soil, surface water and ground water. Wind can seasonally erode waste impoundments in all types of climate, but the erosion intensifies and persists for more of each year as regional aridity increases. As clouds of dust are often observed billowing across the top surfaces of waste impoundments in dry windy weather, there is a common misconception that dust arises from erosion of the top surface of an impoundment, resulting in much effort and money being misspent on top treatments when in fact the sloped sides of the impoundments are the true source of blown dust. This paper offers a brief review of general waste impoundment wind erosion issues and then focuses in more detail on the mechanics of how wind erodes surfaces of waste impoundments. Recommendations are offered for mitigating the effects of wind-eroded dust.

Assessment of water quality index of bore well water samples from some selected locations of South Gujarat, India.

PubMed

Tripathi, S; Patel, H M; Srivastava, P K; Bafna, A M

2013-10-01

The present study calculates the water quality index (WQI) of some selected sites from South Gujarat (India) and assesses the impact of industries, agriculture and human activities. Chemical parameters were monitored for the calculation of WQI of some selected bore well samples. The results revealed that the WQI of the some bore well samples exceeded acceptable levels due to the dumping of wastes from municipal, industrial and domestic sources and agricultural runoff as well. Inverse Distance Weighting (IDW) was implemented for interpolation of each water quality parameter (pH, EC, alkalinity, total hardness, chloride, nitrate and sulphate) for the entire sampled area. The bore water is unsuitable for drinking and if the present state of affairs continues for long, it may soon become an ecologically dead bore.

Abandoned mines, mountain sports, and climate variability: Implications for the Colorado tourism economy

NASA Astrophysics Data System (ADS)

Todd, Andrew; McKnight, Diane; Wyatt, Lane

Until recently, the allure of the mountains in the American West was primarily extractive, for commodities like timber, water, and precious metals [Baron et. al., 2000]. Now, the effective marketing and management of the regions “white gold” by the ski industry has stimulated significant recreation-related growth and development in the last several decades. Under an uncertain climatic future, however, these burgeoning industries, and the communities that have grown up in relation to them, are facing water quality constraints inherited from historical mining practices, causing mountain water to become a limited resource more valuable than the precious metals of the past. Further, the current lack of proven, in-situ approaches for addressing distributed, mining waste pollution of fresh water complicates potential remediation efforts.

Characteristics and management of infectious industrial waste in Taiwan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, M.-C.; Lin, Jim Juimin

Infectious industrial waste management in Taiwan is based on the specific waste production unit. In other countries, management is based simply on whether the producer may lead to infectious disease. Thus, Taiwan has a more detailed classification of infectious waste. The advantage of this classification is that it is easy to identify the sources, while the disadvantage lies in the fact that it is not flexible and hence increases cost. This study presents an overview of current management practices for handling infectious industrial waste in Taiwan, and addresses the current waste disposal methods. The number of small clinics in Taiwanmore » increased from 18,183 to 18,877 between 2003 and 2005. Analysis of the data between 2003 and 2005 showed that the majority of medical waste was general industrial waste, which accounted for 76.9%-79.4% of total medical waste. Infectious industrial waste accounted for 19.3%-21.9% of total medical waste. After the SARS event in Taiwan, the amount of infectious waste reached 19,350 tons in 2004, an increase over the previous year of 4000 tons. Waste minimization was a common consideration for all types of waste treatment. In this study, we summarize the percentage of plastic waste in flammable infectious industrial waste generated by medical units, which, in Taiwan was about 30%. The EPA and Taiwan Department of Health have actively promoted different recycling and waste reduction measures. However, the wide adoption of disposable materials made recycling and waste reduction difficult for some hospitals. It has been suggested that enhancing the education of and promoting communication between medical units and recycling industries must be implemented to prevent recyclable waste from entering the incinerator.« less

State Waste Discharge Permit application for industrial discharge to land: 200 East Area W-252 streams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This document constitutes the WAC 173-216 State Waste Discharge Permit application for six W-252 liquid effluent streams at the Hanford Site. Appendices B through H correspond to Section B through H in the permit application form. Within each appendix, sections correspond directly to the respective questions on the application form. The appendices include: Product or service information; Plant operational characteristics; Water consumption and waterloss; Wastewater information; Stormwater; Other information; and Site assessment.

Managing water and salinity with desalination, conveyance, conservation, waste-water treatment and reuse to counteract climate variability in Gaza

NASA Astrophysics Data System (ADS)

Rosenberg, D. E.; Aljuaidi, A. E.; Kaluarachchi, J. J.

2009-12-01

We include demands for water of different salinity concentrations as input parameters and decision variables in a regional hydro-economic optimization model. This specification includes separate demand functions for saline water. We then use stochastic non-linear programming to jointly identify the benefit maximizing set of infrastructure expansions, operational allocations, and use of different water quality types under climate variability. We present a detailed application for the Gaza Strip. The application considers building desalination and waste-water treatment plants and conveyance pipelines, initiating water conservation and leak reduction programs, plus allocating and transferring water of different qualities among agricultural, industrial, and urban sectors and among districts. Results show how to integrate a mix of supply enhancement, conservation, water quality improvement, and water quality management actions into a portfolio that can economically and efficiently respond to changes and uncertainties in surface and groundwater availability due to climate variability. We also show how to put drawn-down and saline Gaza aquifer water to more sustainable and economical use.

Design and implementation of integrated solid wastes management pattern in industrial zones, case study of Shahroud, Iran.

PubMed

Saeid, Nazemi; Roudbari, Aliakbar; Yaghmaeian, Kamyar

2014-01-14

The aim of the study was to design and implementation of integrated solid wastes management pattern in Shahroud industrial zone, evaluates the results and determine possible performance problems. This cross - sectional study was carried out for 4 years in Shahroud industrial zone and the implementation process included:1- Qualitative and quantitative analysis of all solid waste generated in the city, 2- determine the current state of solid waste management in the zone and to identify programs conducted, 3- Design and implementation of integrated solid wastes management pattern including design and implementation of training programs, laws, penalties and incentives and explain and implement programs for all factories and 4- The monitoring of the implementation process and determine the results. Annually, 1,728 tons of solid wastes generated in the town including 1603 tons of industrial wastes and 125 tons of municipal wastes. By implementing this pattern, the two separated systems of collection and recycling of domestic and industrial wastes was launched in this zone. Also consistent with the goals, the amount of solid wastes generated and disposed in 2009 was 51.5 and 28.6 kg per 100 million Rials production, respectively. Results showed that implementation of pattern of separated collection, training programs, capacity building, providing technical services, completing chain of industries and strengthening the cooperation between industrial estate management and industrial units could greatly reduce the waste management problems.

Integrated approach for demarcating subsurface pollution and saline water intrusion zones in SIPCOT area: a case study from Cuddalore in Southern India.

PubMed

Sankaran, S; Sonkamble, S; Krishnakumar, K; Mondal, N C

2012-08-01

This paper deals with a systematic hydrogeological, geophysical, and hydrochemical investigations carried out in SIPCOT area in Southern India to demarcate groundwater pollution and saline intrusion through Uppanar River, which flows parallel to sea coast with high salinity (average TDS 28, 870 mg/l) due to back waters as well as discharge of industrial and domestic effluents. Hydrogeological and geophysical investigations comprising topographic survey, self-potential, multi-electrode resistivity imaging, and water quality monitoring were found the extent of saline water intrusion in the south and pockets of subsurface pollution in the north of the study area. Since the area is beset with highly permeable unconfined quaternary alluvium forming potential aquifer at shallow depth, long-term excessive pumping and influence of the River have led to lowering of the water table and degradation of water quality through increased salinity there by generating reversal of hydraulic gradient in the south. The improper management of industrial wastes and left over chemicals by closed industries has led surface and subsurface pollution in the north of the study area.

Urbanization in Pearl River Delta area in past 20 years: remote sensing of impact on water quality

NASA Astrophysics Data System (ADS)

Wang, Yunpeng; Fan, Fenglei; Zhang, Jinqu; Xia, Hao; Ye, Chun

2004-11-01

The Pearl River Delta of Guangdong province in China is one of the world"s largest growths in urbanization for the past 20 years. The objective of this research is to explore the relationship between urbanization and water quality in this area. Present and past remote sensing data including MSS< TM/ETM and ASTER are used to research the urbanization and its impact on water quality. Land use and water quality information are extracted from remote sensing data. Data of population, industrial and agricultural productivity indices are integrated with the thematic maps derived from remote sensing data by GIS method. Spatial analysis methods are applied on these data and the results indicate that population, waste water both from household and industrial and chemical fertilizer consumptions are main controls of the regional water quality and environment.

Sustainable Sources of Biomass for Bioremediation of Heavy Metals in Waste Water Derived from Coal-Fired Power Generation

PubMed Central

Saunders, Richard J.; Paul, Nicholas A.; Hu, Yi; de Nys, Rocky

2012-01-01

Biosorption of heavy metals using dried algal biomass has been extensively described but rarely implemented. We contend this is because available algal biomass is a valuable product with a ready market. Therefore, we considered an alternative and practical approach to algal bioremediation in which algae were cultured directly in the waste water stream. We cultured three species of algae with and without nutrient addition in water that was contaminated with heavy metals from an Ash Dam associated with coal-fired power generation and tested metal uptake and bioremediation potential. All species achieved high concentrations of heavy metals (to 8% dry mass). Two key elements, V and As, reached concentrations in the biomass of 1543 mg.kg−1 DW and 137 mg.kg−1 DW. Growth rates were reduced by more than half in neat Ash Dam water than when nutrients were supplied in excess. Growth rate and bioconcentration were positively correlated for most elements, but some elements (e.g. Cd, Zn) were concentrated more when growth rates were lower, indicating the potential to tailor bioremediation depending on the pollutant. The cosmopolitan nature of the macroalgae studied, and their ability to grow and concentrate a suite of heavy metals from industrial wastes, highlights a clear benefit in the practical application of waste water bioremediation. PMID:22590550

Application of mixed based membrane technology from component materials bintaro, zeolite and bentonite to reduction of songket waste liquid cloth

NASA Astrophysics Data System (ADS)

Dahlan, Muhammad Hatta; Saleh, Abdullah; Asip, Faisol; Makmun, Akbar; Defi

2017-11-01

Application of membrane technology based on clay mixture, Activated Carbon from Bintaro, Zeolite and Bentonit to process the waste water of Songket cloth is Palembang traditionally cloth. The applied research is into the superior field of industrial and household waste processing with membrane ceramic technology. The objective of this research is to design the liquid waste separation tool of jumputan cloth using better and simpler ceramic membrane so that it can help the artisans of Palembang songket or songket in processing the waste in accordance with the standard of environmental quality standard (BML) and Pergub Sumsel no. 16 in 2005. The specific target to be achieved can decrease the waste of cloth jumputan in accordance with applicable environmental quality standards the method used in achieving the objectives of this study using 2 processes namely the adsorption process using activated carbon and the separation process using a ceramic membrane based on the composition of the mixture. The activated carbon from bintaro seeds is expected to decrease the concentration of liquid waste of Songket cloth. Bintaro seeds are non-edible fruits where the composition contains organic ingredients that can absorb because contains dyes and filler metals. The process of membranization in the processing is expected to decrease the concentration of waste better and clear water that can be used as recycled water for household use. With the composition of a mixture of clay-based materials: zeolite, bentonit, activated carbon from bintaro seeds are expected Find the solution and get the novelty value in the form of patent in this research

Environmental assessment of cement/foundry sludge products.

PubMed

Ruiz, M C; Andrés, A; Irabien, A

2003-05-01

This work deals with the environmental assessment of products based on cement and a waste from a cast iron activity. The waste is a foundry sludge from wastewater treatment previously characterized. This industrial waste shows a high water content (62.4%) and a hazardous behavior due to its metallic content mainly Zn (16.5%), together with a low fraction of organic pollutants, mainly phenolic compounds. The feasibility of immobilizing both typs of contaminants was studied using Portland cement as binder at different cement/waste ratios. The parameters of environmental control were the ecotoxicity and mobilization of zinc and phenolic compounds, all determined on the basis of compliance leaching tests. The acid neutralization capacity of the cement/waste products was measured in order to obtain information on their buffering capacity. Experimental results from chemical analysis of leachates led to a non ecotoxic character of cement/waste products Although the metallic ions were mobilized within the cement mattices, the organic matter did not allow the formation of monolithic forms and an efficient immobilization of phenolic compounds. Concerning the acid neutralization capacity, this parameter was shown to depend mainly on the quantity of cement, although a decrease in alkalinity was observed when the amount of water in the cement/waste products increased.

Guide to Louisiana's ground-water resources

USGS Publications Warehouse

Stuart, C.G.; Knochenmus, D.D.; McGee, B.D.

1994-01-01

Ground water is one of the most valuable and abundant natural resources of Louisiana. Of the 4-.4 million people who live in the State, 61 percent use ground water as a source for drinking water. Most industrial and rural users and half of the irrigation users in the State rely on ground water. Quantity, however, is not the only aspect that makes ground water so valuable; quality also is important for its use. In most areas, little or no water treatment is required for drinking water and industrial purposes. Knowledge of Louisiana's ground-water resources is needed to ensure proper development and protection of this valuable resource. This report is designed to inform citizens about the availability and quality of ground water in Louisiana. It is not intended as a technical reference; rather, it is a guide to ground water and the significant role this resource plays in the state. Most of the ground water that is used in the State is withdrawn from 13 aquifers and aquifer systems: the Cockfield, Sparta, and Carrizo-Wilcox aquifersin northern Louisiana; Chicot aquifer system, Evangeline aquifer, Jasper aquifer system, and Catahoula aquifer in central and southwestern Louisiana; the Chicot equivalent, Evangeline equivalent, and Jasper equivalent aquifer systems in southeastern Louisiana; and the MississippiRiver alluvial, Red River alluvial, and upland terrace aquifers that are statewide. Ground water is affected by man's activities on the land surface, and the major ground-water concerns in Louisiana are: (1) contamination from surface disposal of hazardous waste, agricultural chemicals, and petroleum products; (2) contamination from surface wastes and saltwater through abandoned wells; (3) saltwater encroachment; and (4) local overdevelopment. Information about ground water in Louisiana is extensive and available to the public. Several State and Federal agencies provide published and unpublished material upon request.

Superfund Record of Decision (EPA Region 5): Midco II, Gary, IN. (First remedial action), (amendment), April 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The 7-acre Midco II site is an abandoned chemical waste storage and disposal facility in Gary, Indiana. Land use in the surrounding area is predominantly industrial. The underlying aquifer, which is used primarily for non-drinking purposes, is highly susceptible to contamination from surface sources. From 1976 to 1978, the site was used for treatment, storage, and disposal of chemical and bulk liquid wastes. The ROD amends a 1989 ROD that addressed the remaining contaminated soil, pit wastes, and ground water by treatment of an estimated 35,000 cubic yards of soil wastes. The amended remedy reduces the estimated amount of soilmore » to be treated, as a result of new information on arsenic data and amended soil CALs, further defines the site cover requirements, and further defines the requirements for deep well injection of contaminated ground water. The primary contaminants of concern affecting the subsurface soil, sediment, and ground water are VOCs, including methylene chloride, benzene, toluene, TCE, and xylenes; other organics, including PCBs, phenols, and PAHs; and metals, including chromium, and lead. The amended remedial action for the ROD is included.« less

A QUALITATIVE APPROACH IN COMPLIANCE MONITORING OF MICROORGANISMS AND EVALUATION OF BIOSOLIDS RISK MANAGEMENT

EPA Science Inventory

Municipal wastewaters receive discharges from homes, commercial establishments, industry and hospitals. Combined sewer systems carry waste from all the above sources as well as storm water. Within such mixtures are the microorganisms which reside in virtually all parts of the s...

PATHOGENS OF CONCERN AND THE NEED FOR ANALYTICAL METHODS DEVELOPMENT, STANDARDIZATION, AND VALIDATION.

EPA Science Inventory

Municipal wastewaters receive discharges from homes, commercial establishments, industry and hospitals. Combined sewer systems carry waste from all the above sources as well as storm water. Within such mixtures are the microorganisms which reside in virtually all parts of the s...

Evaluating impacts of pulp and paper mill process changes on bioactive contaminant loading to St. Louis Bay.

EPA Science Inventory

As a convergence point for human waste streams, wastewater treatment plants are recognized as point sources through which contaminants originating from domestic, industrial, and commercial activities enter surface waters. Effluent from the Western Lake Superior Sanitary District ...

MEASUREMENT OF VOLATILE CHEMICAL EMISSIONS FROM WASTEWATER BASINS

EPA Science Inventory

The objective of this project was to measure the rate at which selected volatile organic carbon (VOC) compounds are being emitted to air from waste-water treatment basins of the pulp and paper industry. The emission rates of methanol, acetone and acetaldehyde were measured and th...

The Highland Park Environmental Health Plan: Evaluation and Recommendations for Improving the Urban Environment.

ERIC Educational Resources Information Center

Michigan State Dept. of Commerce, Lansing. Community Planning Div.

The Highland Park environmental health plan includes the following components: Legal and administrative and programmatic relationships, planning studies, residential environment, disease vector control, water and sewage systems, sanitation, air pollution, food protection, industrial and radiological health, and solid waste facilities. (JR)

Cleaner production options for reducing industrial waste: the case of batik industry in Malang, East Java-Indonesia

NASA Astrophysics Data System (ADS)

Sirait, M.

2018-01-01

The aim of this research is to conduct cleaner production options for improving the environmental performance during the production of batik industry, the case of UKM batik, Malang, East Java. Batik industry is one of small and medium textile industry which has contribution to economic growth in Malang. However, during production the batik, it generates wastewater that has potential to decrease the environmental performance. Wastewater from Celaket batik industry has BOD, COD, TSS, and pH level is far larger than the threshold of water quality standard as a result of use chemical substance during the dyes processing. In order to prevent generating wastewater, this study utilized cleaner production options, such as substitution of input material.Substitution of input material for dyes process was implemented by replacement chemical dyes (e.g.indigosol, nafthol, rapid) with natural dyes (e.g. Indigofero Tintoria). Modifying of technology/equipment was conducted by developing wastewater treatment equipment to reduce waste of batik production. The implementation of this strategy was carried out by changing input material from chemical dyes with natural dyes. The CP uptake could reduce significantly the environmental impact in term of reduction of COD, BOD, and TSS.

Understanding resilience in industrial symbiosis networks: insights from network analysis.

PubMed

Chopra, Shauhrat S; Khanna, Vikas

2014-08-01

Industrial symbiotic networks are based on the principles of ecological systems where waste equals food, to develop synergistic networks. For example, industrial symbiosis (IS) at Kalundborg, Denmark, creates an exchange network of waste, water, and energy among companies based on contractual dependency. Since most of the industrial symbiotic networks are based on ad-hoc opportunities rather than strategic planning, gaining insight into disruptive scenarios is pivotal for understanding the balance of resilience and sustainability and developing heuristics for designing resilient IS networks. The present work focuses on understanding resilience as an emergent property of an IS network via a network-based approach with application to the Kalundborg Industrial Symbiosis (KIS). Results from network metrics and simulated disruptive scenarios reveal Asnaes power plant as the most critical node in the system. We also observe a decrease in the vulnerability of nodes and reduction in single points of failure in the system, suggesting an increase in the overall resilience of the KIS system from 1960 to 2010. Based on our findings, we recommend design strategies, such as increasing diversity, redundancy, and multi-functionality to ensure flexibility and plasticity, to develop resilient and sustainable industrial symbiotic networks. Copyright © 2014 Elsevier Ltd. All rights reserved.

Energy optimization of water and wastewater management for municipal and industrial applications conference

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-08-01

These proceedings document the presentations given at the Energy Optimization of Water and Wastewater Management for Municipal and Industrial Applications, Conference, sponsored by the Department of Energy (DOE). The conference was organized and coordinated by Argonne National Laboratory. The conference focused on energy use on conservation in water and wastewater. The General Session also reflects DOE's commitment to the support and development of waste and wastewater systems that are environmentally acceptable. The conference proceedings are divided into two volumes. Volume 1 contains the General Session and Sessions 1 to 5. Volume 2 covers Sessions 6 to 12. Separate abstracts aremore » prepared for each item within the scope of the Energy Data Base.« less

A Review on Landfill Management in the Utilization of Plastic Waste as an Alternative Fuel

NASA Astrophysics Data System (ADS)

Hidayah, Nurul; Syafrudin

2018-02-01

Wastes from landfills originate from many spheres of life. These are produces as a result of human activities either domestically or industrially. The global plastic production increased over years due to the vast applications of plastics in many sectors. The continuous demand of plastics caused the plastic wastes accumulation in the landfill consumed a lot of spaces that contributed to the environmental. In addition, economic growth and development also increased our demand and dependency on plastics which leads to its accumulation in landfills imposing risk on human health, animals and cause environmental pollution problems such as ground water contamination, sanitary related issues, etc. The management and disposal of plastic waste have become a major concern, especially in developing cities. The idea of waste to energy recovery is one of the promising techniques used for managing the waste of plastic. Hence, this paper aims review at utilizing of plastic as an alternative fuel.

Lake Water Quality Improvement by Using Waste Mussel Shell Powder as an Adsorbent

NASA Astrophysics Data System (ADS)

Zukri, N. I.; Khamidun, M. H.; Sapiren, M. S.; Abdullah, S.; Rahman, M. A. A.

2018-04-01

Lake water in UTHM was slightly greenish in color indicating the eutrophication process. Eutrophication problem is due to excessive amount of nutrient in the lake water which causes nuisance growth of algae and other aquatic plant. The improvement of lake water quality should be conducted wisely in preventing from eutrophication problem by using a suitable water treatment method. Natural materials, agricultural wastes and industrial wastes are locally available sources can be utilized as low-cost adsorbents. The natural abundant source of waste mussel’s shells is advantages to use as basis material to produce the low cost adsorbent for water treatment. Batch experiments were carried out with the preparation 500 ml volume of lake water sample with the dosage of 2.5g, 7.5g and 12.5g. Then the solution shaking in an incubator with 200 rpm shaking speed. The various dosage of mussel shell greatly affected pollutants removal. Both of NH4+ and PO43- have a higher percentage removal with 31.28% and 21.74% at the 7.5g of sample dosage. Other parameters such as COD and TSS also shown good percentage of removal at 7.5g of dosage sample with 44.45% and 25% respectively. While, dosage at 2.5g was performed as a good adsorption capacity of NH4+, PO43-, COD and TSS as high as 0.142, 0.234, 7.6 and 20 mg/g, respectively. These experimental results suggested that the use of mussel shell powder as good basis material in removing pollutants from lake water.

40 CFR 98.463 - Calculating GHG emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Industrial Waste Landfills § 98.463 Calculating GHG emissions. (a) For each industrial waste landfill subject to the reporting requirements of this subpart... which emissions are calculated. Wx = Quantity of waste disposed in the industrial waste landfill in year...

Anaerobic sequencing batch reactor in pilot scale for treatment of tofu industry wastewater

NASA Astrophysics Data System (ADS)

Rahayu, Suparni Setyowati; Purwanto, Budiyono

2015-12-01

The small industry of tofu production process releases the waste water without being processed first, and the wastewater is directly discharged into water. In this study, Anaerobic Sequencing Batch Reactor in Pilot Scale for Treatment of Tofu Industry was developed through an anaerobic process to produce biogas as one kind of environmentally friendly renewable energy which can be developed into the countryside. The purpose of this study was to examine the fundamental characteristics of organic matter elimination of industrial wastewater with small tofu effective method and utilize anaerobic active sludge with Anaerobic Sequencing Bath Reactor (ASBR) to get rural biogas as an energy source. The first factor is the amount of the active sludge concentration which functions as the decomposers of organic matter and controlling selectivity allowance to degrade organic matter. The second factor is that HRT is the average period required substrate to react with the bacteria in the Anaerobic Sequencing Bath Reactor (ASBR).The results of processing the waste of tofu production industry using ASBR reactor with active sludge additions as starter generates cumulative volume of 5814.4 mL at HRT 5 days so that in this study it is obtained the conversion 0.16 L of CH4/g COD and produce biogas containing of CH4: 81.23% and CO2: 16.12%. The wastewater treatment of tofu production using ASBR reactor is able to produce renewable energy that has economic value as well as environmentally friendly by nature.

Evaluation of Practicing sustainable Industrial Solid Waste Minimization by Manufacturing Firms in Malaysia: Strengths and Weaknesses.

PubMed

Mallak, Shadi Kafi; Bakri Ishak, Mohd; Mohamed, Ahmad Fariz

2016-09-13

Malaysia is facing an increasing trend in industrial solid waste generation due to industrial development.Thus there is a paramount need in taking a serious action to move toward sustainable industrial waste management. The main aim of this study is to assess practicing solid waste minimization by manufacturing firms in Shah Alam industrial state, Malaysia. This paper presents a series of descriptive and inferential statistical analysis regarding the level and effects of practicing waste minimization methods, and seriousness of barriers preventing industries from practicing waste minimization methods. For this purpose the survey questions were designed such that both quantitative (questionnaire) and qualitative (semi-structures interview) data were collected concurrently. Analysis showed that, the majority of firms (92%) dispose their wastes rather than practice other sustainable waste management options. Also waste minimization methods such as segregation of wastes, on-site recycle and reuse, improve housekeeping and equipment modification were found to have significant contribution in waste reduction (p<0.05). Lack of expertise (M=3.50), lack of enough information (M= 3.54), lack of equipment modification (M= 3.16) and lack of specific waste minimization guidelines (M=3.49) have higher mean scores comparing with other barriers in different categories. These data were interpreted for elaborating of SWOT and TOWS matrix to highlight strengths, weaknesses, threats and opportunities. Accordingly, ten policies were recommended for improvement of practicing waste minimization by manufacturing firms as the main aim of this research. Implications This manuscript critically analysis waste minimization practices by manufacturing firms in Malaysia. Both qualitative and quantitative data collection and analysis were conducted to formulate SWOT and TOWS matrix in order to recommend policies and strategies for improvement of solid waste minimization by manufacturing industries. The results contribute to the knowledge and the findings of this study provide a useful baseline information and data on industrial solid waste generation and waste minimization practice.

Periodic processes in vapor phase biofiltration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moe, W.M.; Irvine, R.L.

1998-07-01

Most industrial processes and environmental remediation activities generate large volumes of air contaminated with low concentrations of volatile organic compounds. Carbon adsorption is the most widely used conventional treatment technology, but it has many drawbacks including secondary waste streams and excessive regeneration costs. Biofiltration, a microbial-based treatment technology, removes and biodegrades contaminants from a wide variety of waste streams without the disadvantages of carbon adsorption. In biofiltration, contaminated air flows through a packed bed containing microorganisms which convert contaminants primarily into carbon dioxide, water, and biomass. This paper describes how periodically operated, controlled unsteady state conditions were imposed on biofiltersmore » which used a new polyurethane foam medium that couples high porosity, suitable pore size, and low density with an ability to sorb water. The potential benefits associated with the controlled, unsteady-state operation of biofilters containing this new polyurethane foam medium are described herein. An example system treating a toluene contaminated waste gas is presented.« less

Marine recreation and public health microbiology: Quest for the ideal indicator

USGS Publications Warehouse

Griffin, Dale W.; Lipp, Erin K.; McLaughlin, Molly R.; Rose, Joan B.

2001-01-01

Four-fifths of the population of the United States live in close proximity to the oceans or Great Lakes, and approximately 100 million Americans use the marine environment for recreation each year (Thurman 1994). Consequently, contamination of lakes, rivers, and coastal waters raises significant public health issues. Among the leading sources of chemical and biological contamination of these waters and associated beaches are sewer systems, septic tanks, stormwater runoff, industrial wastes, wastewater injection wells, cesspits, animal wastes, commercial and private boat wastes, and human recreation. In 1997, 649 beach closings or advisories were caused by sewage spills and overflows (NRDC 1998). In Florida alone, approximately 500 million gallons of sewage were released along the coast each year during the late 1980s (Neshyba 1987). Thus one of the primary concerns in public health is the risk that humans using the marine environment for recreational activities will encounter microbial pathogens.

Marine recreation and public health microbiology: quest for the ideal indicator

USGS Publications Warehouse

Griffin, Dale W.; Lipp, Erin K.; McLaughlin, Molly R.; Rose, Joan B.

2001-01-01

Four-fifths of the population of the United States live in close proximity to the oceans or Great Lakes, and approximately 100 million Americans use the marine environment for recreation each year (Thurman 1994). Consequently, contamination of lakes, rivers, and coastal waters raises significant public health issues. Among the leading sources of chemical and biological contamination of these waters and associated beaches are sewer systems, septic tanks, stormwater runoff, industrial wastes, wastewater injection wells, cesspits, animal wastes, commercial and private boat wastes, and human recreation. In 1997, 649 beach closings or advisories were caused by sewage spills and overflows (NRDC 1998). In Florida alone, approximately 500 million gallons of sewage were released along the coast each year during the late 1980s (Neshyba 1987). Thus one of the primary concerns in public health is the risk that humans using the marine environment for recreational activities will encounter microbial pathogens.

Wastewater characterization survey, Victor Valley Wastewater Reclamation Authority and hazardous-waste survey at George AFB, California. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Binovi, R.D.; Ng, E.K.; Tetla, R.A.

1987-01-01

This is a report of a survey of the Victor Wastewater Reclamation Authority Sewerage system, the sewage treatment plant, and effluent from the various operations at George AFB, California. The scope of work included the characterization of the wastewater from George AFB, as well as characterization of effluents from 29 oil/water separators servicing industrial operations on base, flow measurements at three locations on base, a microbiological evaluation of aeration basin foam, bench-scale activated-sludge studies, and a review of results from previous surveys. Recommendations: (1) AFFF (Aqueous Film Forming Foam) should never be discharged to the sewer. (2) Programming for pretreatmentmore » should proceed at selected operations. (3) More waste and wastestream analysis be performed. (4) Upgrade waste accumulation points. (5) Implement an aggressive inspection program for oil/water separators. (6) Cut down on nonessential washing.« less

Production of biodiesel by enzymatic transesterification of waste sardine oil and evaluation of its engine performance.

PubMed

Arumugam, A; Ponnusami, V

2017-12-01

Waste sardine oil, a byproduct of fish industry, was employed as a low cost feedstock for biodiesel production. It has relatively high free fatty acid (FFA) content (32 mg KOH/g of oil). Lipase enzyme immobilized on activated carbon was used as the catalyst for the transesterification reaction. Process variables viz. reaction temperature, water content and oil to methanol molar ratio were optimized. Optimum methanol to oil molar ratio, water content and temperature were found to be 9:1, 10 v/v% and 30 °C respectively. Reusability of immobilized lipase was studied and it was found after 5 cycles of reuse there was about 13% drop in FAME yield. Engine performance of the produced biodiesel was studied in a Variable Compression Engine and the results confirm that waste sardine oil is a potential alternate and low-cost feedstock for biodiesel production.

Elimination of micropollutants and hazardous substances at the source in the chemical and pharmaceutical industry.

PubMed

Blöcher, C

2007-01-01

Industrial wastewater, especially from chemical and pharmaceutical production, often contains substances that need to be eliminated before being discharged into a biological treatment plant and following water bodies. This can be done within the production itself, in selected waste water streams or in a central treatment plant. Each of these approaches has certain advantages and disadvantages. Furthermore, a variety of wastewater treatment processes exist that can be applied at each stage, making it a challenging task to choose the best one in economic and ecological terms. In this work a general approach for that and examples from practice are discussed.

Some aspects of applying nanostructured materials in air filtration, water filtration and electrical engineering

NASA Astrophysics Data System (ADS)

Kimmer, Dusan; Vincent, Ivo; Lovecka, Lenka; Kazda, Tomas; Giurg, Adam; Skorvan, Ondrej

2017-05-01

Nanostructures prepared from nanofibres and nanostructured composites prepared from nanofibres and fillers are gradually becoming increasingly demanded materials for applications in various industrial branches connected with catalysis, environment protection (air filtration, waste water treatment, sound absorption), in biological engineering, electronics (battery separators, electrode materials), etc. Selected applications of these materials prepared in the company SPUR a.s. are summed up in the following presentation.

Progress toward a ground-water-quality monitoring network for Idaho

USGS Publications Warehouse

Whitehead, R.L.

1978-01-01

The potential for pollution of the aquifers is expected to be greatest in areas of greatest development. In Idaho, population centers and industries tend to be in areas of privately owned irrigated and arable · land. Therefore, these areas are of primary concern for monitoring ground-water quality. Other areas requiring monitoring include those with second-home development, mining and its related processes, and radioactive-waste disposal.

[Lead in the environment of Poland].

PubMed

Dutkiewicz, T; Swiatczak, J

1993-01-01

Lead belongs to those elements which have a great variety of applications in the up-to-date technology. In the form of waste products or automotive wastes it has been brought into a global circulation. The authors attempt to present harmful effects of this "environmental poison" on individual media and human population in Poland. Following published and non-published data, an outline of lead geochemistry, anthropo-genetic sources of lead emission into the environment, concentration of lead in the ambient air, surface water, soil, plants and food, is presented. The data are interpreted on the basis of home maximum allowable concentrations and on the health criteria recommended by international organizations. It was found that the knowledge on the level of pollution of individual environmental media with lead is diversified and incomplete. This hinders a comparable and comprehensive evaluation of lead migration in the natural environment and thus the assessment of exposure magnitude among inhabitants of all regions (voivoships) of the country. Emissions from plants producing and processing non-ferrous metals, industrial waste sites, motor transport especially in central parts of urban and industrial agglomerations, and use of certain mineral fertilizers are recognized as the greatest hazards to the biosphere and human health among all sources of environmental pollution with lead. As appears from the data, the highest level of lead contamination of air, water and soil occurs in the central part of the Upper Silesian Industrial District as well as in the direct vicinity of other plants of non-ferrous metals in Katowice and Legnica voivodships. It was also noted that crops from those agglomerations and from family gardens located near active industrial waste sites or exploited yards may contain amounts of lead exceeding considerably allowable concentrations. It was revealed that in Polish conditions the largest amounts of lead enter children's organism with dirt, dust and food and the smallest with water. Vegetables and potatoes, and in the case of children, milk as well are the main carriers of lead in Polish food, therefore, these products should remain under particular laboratory control. It is acknowledged that preventive measures in areas where the level of environmental pollution with lead is not fully recognized, biological monitoring of lead concentrations in the blood of children, the most sensitive group of population, should be initiated.

Photocatalytic quartz fiber felts with carbon-connected TiO2 nanoparticles for capillarity-driven continuous-flow water treatment

NASA Astrophysics Data System (ADS)

Zhang, Xiaofei; Su, Xiaowen; Gao, Wenqiang; Wang, Fulei; Liu, Zhihe; Zhan, Jie; Liu, Baishan; Wang, Ruosong; Liu, Hong; Sang, Yuanhua

2018-06-01

Immobility of photocatalysts on substrates is a vital factor for the practical application of photocatalysis in polluted water/air treatment. In this study, TiO2 homogenously loaded quartz fiber felt was prepared by assembling of carboxyl-contained organic molecules functionalized TiO2 nanoparticles on the surface of amino group-modified quartz fiber by electrostatic adsorption between them and followed by an anneal process. The immobilization of TiO2 nanoparticles overcomes one main obstacle of the photocatalysts recycling in photocatalysis application. In addition, a plasma treatment endowed the hybrid photocatalyst a high hydrophilic property. Due to the homogeneous distribution of TiO2, charge carriers' separation by carbon, and full contact between water and the photocatalyst derived from the high hydrophilia, the TiO2/quartz fiber felt shows excellent photocatalytic performance. Based on the stable loading and the capillarity effect of the contacted fibers photocatalyst, a demo capillarity-driven continuous-flow water treatment photocatalysis reactor was designed and built up. The TiO2 nanoparticle/quartz fiber hybrid photocatalyst can disposal organic contaminants in actual industrial waste water from a dyeing factory in the continuous-flow reactor. The chemical oxygen demand (COD) of the industrial waste water was decreased from 104 to 45 mg/L, overcoming the problem of deep water treatment which is difficult to solve by other methods. This study provides a new photocatalyst and reaction mode for the continuous-flow photocatalysis application.

[The hygienic evaluation of the mutagenic potential of industrial wastes].

PubMed

Zhurkov, V S; Rusakov, N V; Tonkopiĭ, N I; Sycheva, L P; Akhal'tseva, L V; Neiaskina, E V; Pirtakhiia, N V; Malysheva, A G; Rastiannikov, E G

1998-01-01

A combination of two approaches to assessing the carcinogenic and mutagenic potentials of industrial waste is proposed. One approach includes determination of the carcinogenic and mutagenic properties of individual chemicals of waste, the other involves biological indication of the cumulative mutagenic activity of waste samples. The mutagenic potential of some waste samples of aircraft industry was determined.

Design and implementation of integrated solid wastes management pattern in industrial zones, case study of Shahroud, Iran

PubMed Central

2014-01-01

Background The aim of the study was to design and implementation of integrated solid wastes management pattern in Shahroud industrial zone, evaluates the results and determine possible performance problems. This cross - sectional study was carried out for 4 years in Shahroud industrial zone and the implementation process included:1- Qualitative and quantitative analysis of all solid waste generated in the city, 2- determine the current state of solid waste management in the zone and to identify programs conducted, 3- Design and implementation of integrated solid wastes management pattern including design and implementation of training programs, laws, penalties and incentives and explain and implement programs for all factories and 4- The monitoring of the implementation process and determine the results. Results Annually, 1,728 tons of solid wastes generated in the town including 1603 tons of industrial wastes and 125 tons of municipal wastes. By implementing this pattern, the two separated systems of collection and recycling of domestic and industrial wastes was launched in this zone. Also consistent with the goals, the amount of solid wastes generated and disposed in 2009 was 51.5 and 28.6 kg per 100 million Rials production, respectively. Conclusion Results showed that implementation of pattern of separated collection, training programs, capacity building, providing technical services, completing chain of industries and strengthening the cooperation between industrial estate management and industrial units could greatly reduce the waste management problems. PMID:24423020

Cost effective modular unit for cleaning oil and gas field waste water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zinberg, M.B.; Nenasheva, M.N.; Gafarov, N.A.

1996-12-31

Problems of environmental control involving conservation of water resources are vital for the development of giant oil and gas condensate fields near Caspian Sea (Russia) characterized by water shortages. One of the urgent tasks of oil production industry is to use all field waste water consisting of underground, processing and rain water. It was necessary to construct a new highly effective equipment which could be used in local waste water treatment. Now we have at our disposal a technology and equipment to meet the requirements to the treated water quality. Thus we have installed a modular unit of 100 m{supmore » 3}/a day capacity to clean waste water from oil products, suspended matter and other organic pollutants at Orenburg oil and gas condensate field, Russia. The unit provides with a full treatment of produced water and comprises a settling tank with adhesive facility, the number of sorption filters, Trofactor bioreactors and a disinfecting facility. The equipment is fitted into three boxes measuring 9 x 3.2 x 2.7 in each. The equipment is simple in design that enables to save money, time and space. Sorption filters, bioreactors as well as the Trofactor process are a part of know-how. While working on the unit construction we applied well known methods of settling and sorption. The process of mechanic cleaning is undergoing in the following succession: (1) the gravitational separation in a settling tank where the floated film oil products are constantly gathered and the sediment is periodically taken away, (2) the settled water treatment in sorption Filters of a special kind.« less

Impact of industrial wastewater disposal on surface water bodies in Mostord area, north greater Cairo.

PubMed

Abdel-Sabour, M F; Rabie, F H; Mostafa, T; Hassan, S A

2001-10-01

The studied area (Shoubra El-Khima, Bahteem and Mostorod) lies in the industrial area north of Greater Cairo. The area suffers from several environmental problems such as sewage and disposal of pollutants from the surrounding factories into the surface water pathways in the area. Water samples were collected seasonally from different waterways found in the area, domestic and or industrial liquid wastes from 12 discharge tubes of different factories (as a point source of pollution). Chemical characteristics of different water samples and its heavy metals content were determined using ion coupled plasma technique (ICP). Results indicate that industrial and domestic wastewater samples contain several toxic levels of tested heavy metals (Cd, Co, Pb and Ni) which have a serious impact on surface waterways in the area. Shebin El-Qanater collector drain samples exhibited the highest levels of Cd, Co, Pb and Ni compared to other tested water bodies. Mostorod collector drain samples showed the highest levels of Zn and Cu. Industrial effluent samples collected from Cairo Company for Fabric industry had the highest amounts of total Zn Cu, Cd, Co and Pb, while Delta steel company discharges the highest amounts of total Fe and Mn. Al-Ahleya Plastic Company discharges the highest amounts of total-Ni. Generally, it is necessary to impose the environmental laws and its regulation regarding the industrial wastewater treatments and disposals to minimize the risk of the adverse effects of these pollutants.

Small mammal populations at hazardous waste disposal sites near Houston, Texas, USA

USGS Publications Warehouse

Robbins, C.S.

1990-01-01

Small mammals were trapped, tagged and recaptured in 0?45 ha plots at six hazardous industrial waste disposal sites to determine if populations, body mass and age structures were different from paired control site plots. Low numbers of six species of small mammals were captured on industrial waste sites or control sites. Only populations of hispid cotton rats at industrial waste sites and control sites were large enough for comparisons. Overall population numbers, age structure, and body mass of adult male and female cotton rats were similar at industrial waste sites and control sites. Populations of small mammals (particularly hispid cotton rats) may not suffice as indicators of environments with hazardous industrial waste contamination.

Cytogenetic effects of leachates from tannery solid waste on the somatic cells of Vicia faba.

PubMed

Chandra, Saurabh; Chauhan, L K S; Pande, P N; Gupta, S K

2004-04-01

The contamination of surface- and groundwater by the leaching of solid wastes generated by industrial activities as a result of water runoff and rainfall is a matter of great concern. The leachates from tannery solid waste (TSW), a major environmental pollutant, were examined for their possible genotoxic effects on the somatic cells of Vicia faba. Leachates were prepared from solid wastes procured from leather-tanning industrial sites, and V. faba seedlings were exposed to three test concentrations, 2.5%, 5%, and 10%, through soil and aqueous media for 5 days. The root tips examined for cytogenetic damage revealed that leachate of TSW significantly inhibited the mitotic index and induced significantly frequent chromosomal and mitotic aberrations (CA/MA) in a dose-dependent manner. The chemical analysis of TSW samples revealed that the chief constituents were chromium and nickel, which may cause genetic abnormalities. The frequency of aberrations was found to be higher in the root meristematic cells of Vicia faba exposed through the aqueous medium than those exposed through the soil medium. The results of the present study indicated that contamination of potable water bodies by leachates of TSW may cause genotoxicity. For the biomonitoring of complex mixtures of toxicants with the V. faba bioassay, the use of the aqueous medium seems to be a more promising method than the use of the soil medium. Copyright 2004 Wiley Periodicals, Inc. Environ Toxicol 19: 129-133, 2004.

The effects of BaSO₄ loading on OPC cementing system for encapsulation of BaSO₄ scale from oil and gas industry.

PubMed

Hussein, O; Utton, C; Ojovan, M; Kinoshita, H

2013-10-15

The BaSO4 scales obtained from piping decontamination from oil and gas industries are most often classified as low level radioactive waste. These wastes could be immobilised by stable cement matrix to provide higher safety of handling, transportation, storage and disposal. However, the information available for the effects of the basic formulation such as waste loading on the fundamental properties is still limited. The present study investigated the effect of BaSO4 loading and water content on the properties of OPC-BaSO4 systems containing fine BaSO4 powder and coarse granules. The BaSO4 with different particle size had a marked effect on the compressive strength due to their different effects on hydration products formed. Introduction of fine BaSO4 powder resulted in an increased formation of CaCO3 in the system, which significantly contributed to the compressive strength of the products. Amount of water was important to control the CaCO3 formation, and water to cement ratio of 0.53 was found to be a good level to maintain a low porosity of the products both for fine BaSO4 powder and coarse BaSO4 granule. BaSO4 loading of up to 60 wt% has been achieved satisfying the minimum compressive strength of 5 MPa required for the radioactive wasteforms. Copyright © 2013 Elsevier B.V. All rights reserved.

Forecasting the Amount of Waste-Sewage Water Discharged into the Yangtze River Basin Based on the Optimal Fractional Order Grey Model

PubMed Central

Li, Shuliang; Meng, Wei; Xie, Yufeng

2017-01-01

With the rapid development of the Yangtze River economic belt, the amount of waste-sewage water discharged into the Yangtze River basin increases sharply year by year, which has impeded the sustainable development of the Yangtze River basin. The water security along the Yangtze River basin is very important for China, It is something about water security of roughly one-third of China’s population and the sustainable development of the 19 provinces, municipalities and autonomous regions among the Yangtze River basin. Therefore, a scientific prediction of the amount of waste-sewage water discharged into Yangtze River basin has a positive significance on sustainable development of industry belt along with Yangtze River basin. This paper builds the fractional DWSGM (1,1) (DWSGM (1,1) model is short for Discharge amount of Waste Sewage Grey Model for one order equation and one variable) model based on the fractional accumulating generation operator and fractional reducing operator, and calculates the optimal order of “r” by using particle swarm optimization (PSO) algorithm for solving the minimum average relative simulation error. Meanwhile, the simulation performance of DWSGM (1,1) model with the optimal fractional order is tested by comparing the simulation results of grey prediction models with different orders. Finally, the optimal fractional order DWSGM (1,1) grey model is applied to predict the amount of waste-sewage water discharged into the Yangtze River basin, and corresponding countermeasures and suggestions are put forward through analyzing and comparing the prediction results. This paper has positive significance on enriching the fractional order modeling method of the grey system. PMID:29295517

Is Industry Managing Its Wastes Properly?

ERIC Educational Resources Information Center

Environmental Science and Technology, 1975

1975-01-01

Industry is faced with handling, disposing and recovering vast amounts of waste, much of it as a result of present pollution control technology. Industry has found the technology available, expensive and, without regulation, easy to ignore. Many industries are therefore improperly managing their wastes. (BT)

Surface Disposal of Waste Water Treatment Plant Biosludge--an Important Source of Perfluorinated Compound Contamination in the Environment

EPA Science Inventory

What are “Biosolids”?- “Biosolids” are what remains after WWTP processing Sewage sludge probably a more accurate term - Could contain anything that comes down the pipe to the WWTP, varies greatly depending on community type, industry effluents, plant desig...

An industrial ecology approach to municipal solid waste management: I. Methodology

EPA Science Inventory

Municipal solid waste (MSW) can be viewed as a feedstock for industrial ecology inspired conversions of wastes to valuable products and energy. The industrial ecology principle of symbiotic processes using waste streams for creating value-added products is applied to MSW, with e...

Potential Impacts of Organic Wastes on Small Stream Water Quality

NASA Astrophysics Data System (ADS)

Kaushal, S. S.; Groffman, P. M.; Findlay, S. E.; Fischer, D. T.; Burke, R. A.; Molinero, J.

2005-05-01

We monitored concentrations of dissolved organic carbon (DOC), dissolved oxygen (DO) and other parameters in 17 small streams of the South Fork Broad River (SFBR) watershed on a monthly basis for 15 months. The subwatersheds were chosen to reflect a range of land uses including forested, pasture, mixed, and developed. The SFBR watershed is heavily impacted by organic wastes, primarily from its large poultry industry, but also from its rapidly growing human population. The poultry litter is primarily disposed of by application to pastures. Our monthly monitoring results showed a strong inverse relationship between mean DOC and mean DO and suggested that concentrations of total nitrogen (TN), DOC, and the trace gases nitrous oxide, methane and carbon dioxide are impacted by organic wastes and/or nutrients from animal manure applied to the land and/or human wastes from wastewater treatment plants or septic tanks in these watersheds. Here we estimate the organic waste loads of these watersheds and evaluate the impact of organic wastes on stream DOC and alkalinity concentrations, electrical conductivity, sediment potential denitrification rate and plant stable nitrogen isotope ratios. All of these water quality parameters are significantly correlated with watershed waste loading. DOC is most strongly correlated with total watershed waste loading whereas conductivity, alkalinity, potential denitrification rate and plant stable nitrogen isotope ratio are most strongly correlated with watershed human waste loading. These results suggest that more direct inputs (e.g., wastewater treatment plant effluents, near-stream septic tanks) have a greater relative impact on stream water quality than more dispersed inputs (land applied poultry litter, septic tanks far from streams) in the SFBR watershed. Conductivity, which is generally elevated in organic wastes, is also significantly correlated with total watershed waste loading suggesting it may be a useful indicator of overall watershed waste loading. Although this work was reviewed by EPA and approved for publication, it may not necessarily reflect official Agency policy.

Using stable isotopes in tracing contaminant sources in an industrial area: A case study on the hydrological basin of the Olt River, Romania.

PubMed

Popescu, Raluca; Mimmo, Tanja; Dinca, Oana Romina; Capici, Calogero; Costinel, Diana; Sandru, Claudia; Ionete, Roxana Elena; Stefanescu, Ioan; Axente, Damian

2015-11-15

Tracing pollution sources and transformation of nitrogen compounds in surface- and groundwater is an issue of great significance worldwide due to the increased human activity, translated in high demand of water resources and pollution. In this work, the hydrological basin of an important chemical industrial platform in Romania (Ramnicu Valcea industrial area) was characterized in terms of the physico-chemical and isotope composition of δ(18)O and δ(2)H in water samples and δ(15)N of the inorganic nitrogen species. Throughout a period of one year, water samples from the Olt River and its more important tributaries were collected monthly in the industrial area, when the seasonal and spatial isotope patterns of the surface waters and the main sources of pollution were determined. Higher inorganic nitrogen concentrations (up to 10.2 mg N L(-1)) were measured between November 2012 and April 2013, which were designated as anthropogenic additions using the mixing calculations. The main sources of pollution with inorganic nitrogen were agriculture and residential release. The inorganic nitrogen from the industrial waste water duct had a distinct δ(15)N fingerprint (mean of -8.6‰). Also, one industrial release into the environment was identified for Olt River, at Ionesti site, in November 2012. The mean precipitation samples had the lowest inorganic nitrogen concentrations (less than 5.5 mg N L(-1)) with a distinct δ(15)N fingerprint compared to the surface and industrial waters. Copyright © 2015 Elsevier B.V. All rights reserved.

RCRA, superfund and EPCRA hotline training module. Introduction to: Solid waste programs updated July 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-07-01

The module focuses on EPA`s efforts in two areas: municipal and industrial solid waste. The garbage that is managed by the local governments is known as municipal solid waste (MSW). Garbage excluded from hazardous waste regulation but not typically collected by local governments is commonly known as industrial solid waste. This category includes domestic sewage and other wastewater treatment sludge, demolition and construction wastes, agricultural and mining residues, combustion ash, and industrial process wastes.

Ground-water contamination and legal controls in Michigan

USGS Publications Warehouse

Deutsch, Morris

1963-01-01

The great importance of the fresh ground-water resources of Michigan is evident because 90 percent of the rural and about 70 percent of the total population of the State exclusive of the Detroit metropolitan area are supplied from underground sources. The water-supply and public-health problems that have been caused by some cases of ground-water contamination in the State illustrate the necessity of protecting this vital resource.Manmade and natural contaminants, including many types of chemical and organic matter, have entered many of the numerous aquifers of the State. Aquifers have been contaminated by waste-laden liquids percolating from the surface or from the zone of aeration and by direct injection to the aquifer itself. Industrial and domestic wastes, septic tanks, leaking sewers, flood waters or other poor quality surface waters, mine waters, solids stored or spread at the surface, and even airborne wastes all have been sources of ground-water contamination in Michigan. In addition, naturally occurring saline waters have been induced into other aquifers by overpumping or unrestricted flow from artesian wells, possibly by dewatering operations, and by the deepening of surface stream channels. Vertical migration of saline waters through open holes from formations underlying various important aquifers also has spoiled some of the fresh ground waters in the State. In spite of the contamination that has occurred, however, the total amount of ground water that has been spoiled is only a small part of the total resource. Neither is the contamination so widespread as that of the surface streams of Michigan.Overall legal authority to control most types of ground-water contamination in the State has been assigned by the Michigan Legislature to the Water Resources Commission, although the Department of Conservation and the Health Department also exercise important water-pollution control functions. The Michigan Supreme Court, in an important case upholding the power of the Water Resources Commission to control pollution of ground water, in effect has introduced the doctrine of reasonable use into the law of the State. Excluding controls administered by the Department of Conservation on activities of the oil and gas industry, however, legal controls have not been used abate intrusion of natural saline waters into fresh-water aquifers in response to pumping and other manmade changes in the hydrologic regimen.

Flexible Distributed Energy & Water from Waste for Food and Beverage Industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Ruijie

Food and beverage plants inherently consume a large quantity of water and generate a high volume of wastewater rich in organic content. On one hand, water discharge regulations are getting more stringent over the time, necessitating the use of different technologies to reduce the amount of wastewater and improve the effluent water quality. On the other hand, growing energy and water costs are driving the plants to extract and reuse valuable energy and water from the wastewater stream. An integrated waste-tovalue system uses a combination of anaerobic digester (AD), reciprocating gas engine/boiler, membrane bioreactor (MBR), and reverse osmosis (RO) tomore » recover valuable energy as heat and/or electricity as well as purify the water for reuse. While individual anaerobic digestion and membrane bioreactors are being used in increasing numbers, there is a growing need to integrate them together in a waste-to-value system for enhanced energy and water recovery. However, currently operation of these systems relies heavily on the plant operator to perform periodic sampling and off-line lab analysis to monitor the system performance, detect any abnormal condition due to variations in the wastewater and decide on appropriate remedial action needed. This leads to a conservative design and operation of these systems to avoid any potential upsets that can destabilize the system.« less

Towards zero industrial waste: Utilisation of brick dust waste in sustainable construction.

PubMed

Kinuthia, J M; Nidzam, R M

2011-08-01

Laboratory investigations were carried out to establish the potential utilisation of brick dust (BD) in construction. The dust is a waste material from the cutting of fired clay bricks. Currently, the disposal of the dust is a problem to the brick fabrication company, and hence an environmental pollution concern. The dust was stabilised either used on its own or in combination with Pulverised Fuel Ash (PFA), a by-product material from coal combustion. The traditional stabilisers of lime and/or Portland Cement (PC) were used as controls. The main aim was to use a sustainable stabiliser material, where these stabilisers were partially replaced with Ground Granulated Blastfurnace Slag (GGBS), a by-product material from steel manufacture. Compacted cylinder test specimens were made at typical stabiliser contents and moist cured for up to 56 days prior to testing for compressive and California Bearing Ratio (CBR) strength tests, and to linear expansion during moist curing and subsequent soaking in water. The results obtained showed that partial substitution of the dust with PFA resulted in stronger material compared to using it on its own. The blended stabilisers achieved better performance. These results suggest technological, economic as well as environmental advantages of using the brick dust and similar industrial by-products to achieve sustainable infrastructure development with near zero industrial waste. Copyright © 2011 Elsevier Ltd. All rights reserved.

Waste incineration industry and development policies in China.

PubMed

Li, Yun; Zhao, Xingang; Li, Yanbin; Li, Xiaoyu

2015-12-01

The growing pollution from municipal solid waste due to economic growth and urbanization has brought great challenge to China. The main method of waste disposal has gradually changed from landfill to incineration, because of the enormous land occupation by landfills. The paper presents the results of a study of the development status of the upstream and downstream of the waste incineration industry chain in China, reviews the government policies for the waste incineration power industry, and provides a forecast of the development trend of the waste incineration industry. Copyright © 2015 Elsevier Ltd. All rights reserved.

Water technology for specific water usage.

PubMed

Frimmel, Fritz H

2003-01-01

Water is the basis for life and culture. In addition to the availability of water its quality has become a major issue in industrialized areas and in developing countries as well. Water usage has to be seen as part of the hydrological cycle. As a consequence water management has to be sustainable. The aim of the contribution is to give water usage oriented quality criteria and to focus on the technical means to achieve them. Water is used for many purposes, ranging from drinking and irrigation to a broad variety of technical processes. Most applications need specific hygienic, chemical and/or physical properties. To meet these demands separation and reaction principles are applied. The reuse of water and the application of water treatment with little or no waste and by-product formation is the way to go. Membrane separation and advanced oxidation including catalytic reactions are promising methods that apply natural processes in sustainable technical performance. Thus elimination of specific water constituents (e.g. salts and metals, microorganisms) and waste water cleaning (e.g. pollutants, nutrients and organic water) can be done efficiently. Learning from nature and helping nature with appropriate technology is a convincing strategy for sustainable water management.

40 CFR 266.104 - Standards to control organic emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... DRE trial burn. (5) Low risk waste. Owners and operators of boilers or industrial furnaces that burn... HAZARDOUS WASTE MANAGEMENT FACILITIES Hazardous Waste Burned in Boilers and Industrial Furnaces § 266.104...) of this section, a boiler or industrial furnace burning hazardous waste must achieve a destruction...

40 CFR 266.104 - Standards to control organic emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... DRE trial burn. (5) Low risk waste. Owners and operators of boilers or industrial furnaces that burn... HAZARDOUS WASTE MANAGEMENT FACILITIES Hazardous Waste Burned in Boilers and Industrial Furnaces § 266.104...) of this section, a boiler or industrial furnace burning hazardous waste must achieve a destruction...

Integrated Watershed Pollution Control at Wujingang Canal, China

NASA Astrophysics Data System (ADS)

Zheng, Z.; Yang, X.; Luo, X.

2012-04-01

With a drainage area of 400 square kilometers, Wujingang Canal is located at the economically developed Yangtz Delta of eastern China. As a major tributary, the canal contributes a significant amount of pollutant load to the Lake Tai. Over the past many years, water quality of the canal and its tributaries could not meet the lowest Category V of Chinese surface water quality standard, indicating that its water is not suitable for the purposes of irrigation or scenic views. Major pollution sources in the watershed include industries, residential households, agriculture, fishery, and animal feedlot operations. A comprehensive plan with a budget of 2 billion RMB for the Wujingang watershed pollution control was developed in 2008 and has been implemented progressively ever since. Major components of the plan include: (1) advanced treatment of wastewater from industries and municipal sewage plants for further removal of nitrogen and phosphorous; (2) industrial wastewater reuse; (3) contiguous treatment of sewage from rural residential households with cost-effective technologies such as tower ecofilter system; (4) recycling of rural wastes to generate high-value added products using technologies such as multi-phase anaerobic co-digestion; and (5) making full use of the local landscape and configuring physical, chemical, and biological pollutant treatment structures to build the "clean river network" for treatment of mildly polluted agricultural discharge and surface runoff. Through the implementation of the above measures, water quality of the Wujingang Canal and its tributaries is expected to improve to meet Category IV of Chinese surface water quality standard by 2012, and Category III standard by 2020. Keywords watershed pollution control, non-point source pollution, rural sewage, rural waste, Lake Tai

Novel industrial wastewater treatment integrated with recovery of water and salt under a zero liquid discharge concept.

PubMed

Rajamani, Sengodagounder

2016-03-01

Conventional industrial effluent treatment systems are designed to reduce biochemical oxygen demand (BOD), chemical oxygen demand (COD) but not total dissolved solids (TDS), mainly contributed by chlorides. In addition to the removal of TDS, it is necessary to recover water for reuse to meet the challenges of shortage of quality water. To recover water, the wastewater needs to be further treated by adopting treatment systems including microfilters, low pressure membrane units such as ultrafiltration (UF), membrane bioreactors (MBR), etc., for the application of reverse osmosis (RO) systems. By adopting the RO system, 75%-80% of quality water with <500 mg/L of TDS is recovered from treated effluent. The management of 20%-25% of the saline water rejected from the RO system with high TDS concentration is being addressed by methods such as forced evaporation systems. The recovery of water from domestic and industrial waste for reuse has become a reality. The membrane system has been used for different applications. It has become mandatory to achieve zero liquid discharge (ZLD) in many states in India and other countries such as Spain, China, etc., and resulted in development of new treatment technologies to suit the local conditions.

Equilibrium approach towards water resource management and pollution control in coal chemical industrial park.

PubMed

Xu, Jiuping; Hou, Shuhua; Xie, Heping; Lv, Chengwei; Yao, Liming

2018-08-01

In this study, an integrated water and waste load allocation model is proposed to assist decision makers in better understanding the trade-offs between economic growth, resource utilization, and environmental protection of coal chemical industries which characteristically have high water consumption and pollution. In the decision framework, decision makers in a same park, each of whom have different goals and preferences, work together to seek a collective benefit. Similar to a Stackelberg-Nash game, the proposed approach illuminates the decision making interrelationships and involves in the conflict coordination between the park authority and the individual coal chemical company stockholders. In the proposed method, to response to climate change and other uncertainties, a risk assessment tool, Conditional Value-at-Risk (CVaR) and uncertainties through reflecting parameters and coefficients using probability and fuzzy set theory are integrated in the modeling process. Then a case study from Yuheng coal chemical park is presented to demonstrate the practicality and efficiency of the optimization model. To reasonable search the potential consequences of different responses to water and waste load allocation strategies, a number of scenario results considering environmental uncertainty and decision maker' attitudes are examined to explore the tradeoffs between economic development and environmental protection and decision makers' objectives. The results are helpful for decision/police makers to adjust current strategies adapting for current changes. Based on the scenario analyses and discussion, some propositions and operational policies are given and sensitive adaptation strategies are presented to support the efficient, balanced and sustainable development of coal chemical industrial parks. Copyright © 2018 Elsevier Ltd. All rights reserved.

Strategy of Construction and Demolition Waste Management after Chemical Industry Facilities Removal

NASA Astrophysics Data System (ADS)

Tashkinova, I. N.; Batrakova, G. M.; Vaisman, Ya I.

2017-06-01

Mixed waste products are generated in the process of irrelevant industrial projects’ removal if conventional techniques of their demolition and dismantling are applied. In Russia the number of unused chemical industry facilities including structures with high rate of wear is growing. In removing industrial buildings and production shops it is used conventional techniques of demolition and dismantling in the process of which mixed waste products are generated. The presence of hazardous chemicals in these wastes makes difficulties for their use and leads to the increasing volume of unutilized residues. In the process of chemical industry facilities’ removal this fact takes on special significance as a high level of hazardous chemicals in the waste composition demands for the realization of unprofitable measures aimed at ensuring environmental and industrial safety. The proposed strategy of managing waste originated from the demolition and dismantling of chemical industry facilities is based on the methodology of industrial metabolism which allows identifying separate material flows of recycled, harmful and ballast components, performing separate collection of components during removal and taking necessary preventive measures. This strategy has been tested on the aniline synthesis plant being in the process of removal. As a result, a flow of 10 wt. %, subjected to decontamination, was isolated from the total volume of construction and demolition waste (C&D waste). The considered approach allowed using the resource potential of more than 80wt. % of waste and minimizing the disposed waste volume.

Additional Equipment for Soil Biodegradation

NASA Astrophysics Data System (ADS)

Vondráčková, Terezie; Kraus, Michal; Šál, Jiří

2017-12-01

Intensification of industrial production, increasing citizens’ living standards, expanding the consumer assortment mean in the production - consumption cycle a constantly increasing occurrence of waste material, which by its very nature must be considered as a source of useful raw materials in all branches of human activity. In addition to strict legislative requirements, a number of circumstances characterize waste management. It is mainly extensive transport associated with the handling and storage of large volumes of substances with a large assortment of materials (substances of all possible physical and chemical properties) and high demands on reliability and time coordination of follow-up processes. Considerable differences in transport distances, a large number of sources, processors and customers, and not least seasonal fluctuations in waste and strong price pressures cannot be overlooked. This highlights the importance of logistics in waste management. Soils that are contaminated with oil and petroleum products are hazardous industrial waste. Methods of industrial waste disposal are landfilling, biological processes, thermal processes and physical and chemical methods. The paper focuses on the possibilities of degradation of oil pollution, in particular biodegradation by bacteria, which is relatively low-cost among technologies. It is necessary to win the fight with time so that no ground water is contaminated. We have developed two additional devices to help reduce oil accident of smaller ranges. In the case of such an oil accident, it is necessary to carry out the permeability test of contaminated soil in time and, on this basis, to choose the technology appropriate to the accident - either in-sit biodegradation - at the site of the accident, or on-sit - to remove the soil and biodegrade it on the designated deposits. A special injection drill was developed for in-sit biodegradation, tossing and aeration equipment of the extracted soil was developed for on-sit biodegradation.

Development of sustainable waste management toward zero landfill waste for the petrochemical industry in Thailand using a comprehensive 3R methodology: A case study.

PubMed

Usapein, Parnuwat; Chavalparit, Orathai

2014-06-01

Sustainable waste management was introduced more than ten years ago, but it has not yet been applied to the Thai petrochemical industry. Therefore, under the philosophy of sustainable waste management, this research aims to apply the reduce, reuse, and recycle (3R) concept at the petrochemical factory level to achieve a more sustainable industrial solid waste management system. Three olefin plants in Thailand were surveyed for the case study. The sources and types of waste and existing waste management options were identified. The results indicate that there are four sources of waste generation: (1) production, (2) maintenance, (3) waste treatment, and (4) waste packaging, which correspond to 45.18%, 36.71%, 9.73%, and 8.37% of the waste generated, respectively. From the survey, 59 different types of industrial wastes were generated from the different factory activities. The proposed 3R options could reduce the amount of landfill waste to 79.01% of the amount produced during the survey period; this reduction would occur over a period of 2 years and would result in reduced disposal costs and reduced consumption of natural resources. This study could be used as an example of an improved waste management system in the petrochemical industry. © The Author(s) 2014.

Mercury recovery from mercury-containing wastes using a vacuum thermal desorption system.

PubMed

Lee, Woo Rim; Eom, Yujin; Lee, Tai Gyu

2017-02-01

Mercury (Hg)-containing waste from various industrial facilities is commonly treated by incineration or stabilization/solidification and retained in a landfill at a managed site. However, when highly concentrated Hg waste is treated using these methods, Hg is released into the atmosphere and soil environment. To eliminate these risks, Hg recovery technology using thermal treatment has been developed and commercialized to recover Hg from Hg-containing waste for safe disposal. Therefore, we developed Hg recovery equipment to treat Hg-containing waste under a vacuum of 6.67kPa (abs) at 400°C and recover the Hg. In addition, the dust generated from the waste was separated by controlling the temperature of the dust filtration unit to 230°C. Additionally, water and Hg vapors were condensed in a condensation unit. The Hg removal rate after waste treatment was 96.75%, and the Hg recovery rate as elemental Hg was 75.23%. Copyright © 2016 Elsevier Ltd. All rights reserved.

Industrial waste materials and by-products as thermal energy storage (TES) materials: A review

NASA Astrophysics Data System (ADS)

Gutierrez, Andrea; Miró, Laia; Gil, Antoni; Rodríguez-Aseguinolaza, Javier; Barreneche, Camila; Calvet, Nicolas; Py, Xavier; Fernández, A. Inés; Grágeda, Mario; Ushak, Svetlana; Cabeza, Luisa F.

2016-05-01

A wide variety of potential materials for thermal energy storage (TES) have been identify depending on the implemented TES method, Sensible, latent or thermochemical. In order to improve the efficiency of TES systems more alternatives are continuously being sought. In this regard, this paper presents the review of low cost heat storage materials focused mainly in two objectives: on the one hand, the implementation of improved heat storage devices based on new appropriate materials and, on the other hand, the valorisation of waste industrial materials will have strong environmental, economic and societal benefits such as reducing the landfilled waste amounts, reducing the greenhouse emissions and others. Different industrial and municipal waste materials and by products have been considered as potential TES materials and have been characterized as such. Asbestos containing wastes, fly ashes, by-products from the salt industry and from the metal industry, wastes from recycling steel process and from copper refining process and dross from the aluminium industry, and municipal wastes (glass and nylon) have been considered. This work shows a great revalorization of wastes and by-product opportunity as TES materials, although more studies are needed to achieve industrial deployment of the idea.

Benefits of supplementing an industrial waste anaerobic digester with energy crops for increased biogas production.

PubMed

Nges, Ivo Achu; Escobar, Federico; Fu, Xinmei; Björnsson, Lovisa

2012-01-01

Currently, there is increasing competition for waste as feedstock for the growing number of biogas plants. This has led to fluctuation in feedstock supply and biogas plants being operated below maximum capacity. The feasibility of supplementing a protein/lipid-rich industrial waste (pig manure, slaughterhouse waste, food processing and poultry waste) mesophilic anaerobic digester with carbohydrate-rich energy crops (hemp, maize and triticale) was therefore studied in laboratory scale batch and continuous stirred tank reactors (CSTR) with a view to scale-up to a commercial biogas process. Co-digesting industrial waste and crops led to significant improvement in methane yield per ton of feedstock and carbon-to-nitrogen ratio as compared to digestion of the industrial waste alone. Biogas production from crops in combination with industrial waste also avoids the need for micronutrients normally required in crop digestion. The batch co-digestion methane yields were used to predict co-digestion methane yield in full scale operation. This was done based on the ratio of methane yields observed for laboratory batch and CSTR experiments compared to full scale CSTR digestion of industrial waste. The economy of crop-based biogas production is limited under Swedish conditions; therefore, adding crops to existing industrial waste digestion could be a viable alternative to ensure a constant/reliable supply of feedstock to the anaerobic digester. Copyright © 2011 Elsevier Ltd. All rights reserved.

A new method for recovery of cellulose from lignocellulosic bio-waste: Pile processing.

PubMed

Tezcan, Erdem; Atıcı, Oya Galioğlu

2017-12-01

This paper presents a new delignification method (pile processing) for the recovery of cellulose from lignocellulosic bio-wastes, adapted from heap leaching technology in metallurgy. The method is based on the stacking of cellulosic materials in a pile, irrigation of the pile with aqueous reactive solution from the top, lignin and hemicellulose removal and enrichment of cellulose by the reactive solution while percolation occurs through the bottom of the pile, recirculating the reactive solution after adjusting several values such as chemical concentrations, and allow the system run until the desired time or cellulose purity. Laboratory scale systems were designed using fall leaves (FL) as lignocellulosic waste materials. The ideal condition for FL was noted as: 0.1g solid NaOH addition per gram of FL into the irrigating solution resulting in instant increase in pH to about 13.8, later allowing self-decrease in pH due to delignification over time down to 13.0, at which point another solid NaOH addition was performed. The new method achieved enrichment of cellulose from 30% to 81% and removal of 84% of the lignin that prevents industrial application of lignocellulosic bio-waste using total of 0.3g NaOH and 4ml of water per gram of FL at environmental temperature and pressure. While the stirring reactions used instead of pile processing required the same amount of NaOH, they needed at least 12ml of water and delignification was only 56.1%. Due to its high delignification performance using common and odorless chemicals and simple equipment in mild conditions, the pile processing method has great promise for the industrial evaluation of lignocellulosic bio-waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, J.C.; Hochreitner, J.J.

Investigations of potential sources of groundwater contamination conducted by various regulatory agencies and consultants at four industrial sites in Logan Township, New Jersey found groundwater contamination at all four sites and at properties adjoining two of the sites. The four sites directly overlie the Potomac-Raritan-Magothy aquifer system, the Township's sole source of potable water. One site was a waste-oil processing and storage facility. The major source of groundwater contamination at the site is a lagoon containing waste oil. Groundwater within 1,000 ft of the lagoon is contaminated. The second site is used to maintain, dispatch, and clean chemical-transportation tanks. Potentialmore » sources of groundwater contamination at the site include former wastewater lagoons, leaking storage drums, and leaking tank trucks. Groundwater at and immediately north of the property is contaminated. Organic compounds are manufactured at the third site. Potential sources of groundwater contamination at this site include landfilled industrial wastes. Groundwater underlying the property is contaminated, but there is no evidence of offsite groundwater contamination from this source. The fourth site is used to treat and dispose of hazardous wastes. The major source of groundwater contamination at this site is landfilled residue from waste-treatment processes. Groundwater underlying the property is contaminated, but there is no evidence of off-site groundwater contamination from this source.« less

Construction materials as a waste management solution for cellulose sludge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Modolo, R., E-mail: regina.modolo@ua.pt; Ferreira, V.M.; Machado, L.M.

2011-02-15

Sustainable waste management system for effluents treatment sludge has been a pressing issue for pulp and paper sector. Recycling is always recommended in terms of environmental sustainability. Following an approach of waste valorisation, this work aims to demonstrate the technical viability of producing fiber-cement roof sheets incorporating cellulose primary sludge generated on paper and pulp mills. From the results obtained with preliminary studies it was possible to verify the possibility of producing fiber-cement sheets by replacing 25% of the conventional used virgin long fiber by primary effluent treatment cellulose sludge. This amount of incorporation was tested on an industrial scale.more » Environmental parameters related to water and waste, as well as tests for checking the quality of the final product was performed. These control parameters involved total solids in suspension, dissolved salts, chlorides, sulphates, COD, metals content. In the product, parameters like moisture, density and strength were controlled. The results showed that it is possible to replace the virgin long fibers pulp by primary sludge without impacts in final product characteristics and on the environment. This work ensures the elimination of significant waste amounts, which are nowadays sent to landfill, as well as reduces costs associated with the standard raw materials use in the fiber-cement industrial sector.« less

A hazardous waste from secondary aluminium metallurgy as a new raw material for calcium aluminate glasses.

PubMed

López-Delgado, Aurora; Tayibi, Hanan; Pérez, Carlos; Alguacil, Francisco José; López, Félix Antonio

2009-06-15

A solid waste coming from the secondary aluminium industry was successfully vitrified in the ternary CaO-Al(2)O(3)-SiO(2) system at 1500 degrees C. This waste is a complex material which is considered hazardous because of its behaviour in the presence of water or moisture. In these conditions, the dust can generate gases such as H(2), NH(3), CH(4), H(2)S, along with heat and potential aluminothermy. Only silica sand and calcium carbonate were added as external raw materials to complete the glasses formula. Different nominal compositions of glasses, with Al(2)O(3) ranging between 20% and 54%, were studied to determine the glass forming area. The glasses obtained allow the immobilisation of up to 75% of waste in a multicomponent oxide system in which all the components of the waste are incorporated. The microhardness Hv values varied between 6.05 and 6.62GPa and the linear thermal expansion coefficient, alpha, varied between (62 and 139)x10(-7)K(-1). Several glasses showed a high hydrolytic resistance in deionised water at 98 degrees C.

[Premises to the transboundary environmental crisis in the water tract on the example of water tract of the Kuban-Manych].

PubMed

Dementieva, D M; Dementiev, M S

As a result, of the management of the irrigation system the most part of the runoff headwaters of the river Kuban was transferred to the arid plains of the Stavropol Territory, Rostov Region and Kalmykia Gravity Water via the water tract of the Kuban-Manych. This system was assumed to be supplied by pure mountain water. In fact, 3-4 class contaminated water currently passes to the water intake of the irrigation system (Nevinnomyssky channel). There is a tendency to the further deterioration in the quality of surface waters. It was determined that in the last decades in the catchment area of the upper reaches of the Kuban (Karachaevo-Cherkessia) the population was determined to increase sharply. As a result the discharge of industrial, agricultural, domestic and recreational waste into the river significantly increased. In that in catchment areas there is practically no infrastructure of the acquisition, processing and recycling of waste for the irrigation system. Intensive recreational and transport development of mountainous areas of Karachay-Cherkessia aggravates the situation and may lead to the need for deep water purification for subsequent consumption already in the vast territories of the Central Caucasus. Due to lack of the infrastructure for the water treatment in the upper reaches of the Kuban, it can lead to the serious systemic crisis. It is proposed to start to create in the catchment areas the cost-based system of recycling waste on the base of their processing by pyrolysis.

Engineering Methane and Carbon Dioxide Pathways to Turn Renewable Biogas into Higher-Value Chemicals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greenfield, Derek; Helman, Noah; Clarke, Elizabeth

The United States has a critical need for green manufacturing technologies that can produce a wide range of renewable products at low cost. Industrial Microbes develops biological processes that produce renewable chemicals from organic waste streams. The target chemical for this Phase I project is used to make paints, coatings, and polymers for a multi-billion-dollar market. In addition to the benefits from its green process, the company estimates that the new manufacturing process described here will result in 20-40% cost savings when used at commercial scale. This is possible because the company’s process utilizes waste biogas, an inexpensive feedstock, andmore » is highly efficient: the only byproduct is clean water. For this Phase I project, Industrial Microbes successfully built an enzyme pathway that solves the most difficult challenges of converting biogas into the target chemical. These challenges include the conversion of methane into soluble methanol; the identification of highly-active enzymes; and the production of the target chemical. The company has also completed proof-of-concept by demonstrating that its production strain can utilize raw biogas from a wastewater treatment plant. Achieving these goals required several breakthroughs in transferring enzymes from exotic microorganisms into a commercial one, used commonly for industrial-scale production. In Phase II, Industrial Microbes will work toward commercializing this process by improving carbon efficiency and speed of chemical production. Organic waste streams such as biogas are an underutilized source of renewable carbon and energy; efficient use of such waste streams will reduce the United States’ reliance on petroleum and lower greenhouse gas emissions. The process described here is one of few industrial processes that can convert biogas into commodity products, rather than burning it for energy. If renewable products can be made from biogas economically, companies and governments will find it attractive to collect organic waste streams for biogas production. This can prevent waste from ending up in landfills, where it breaks down into the greenhouse gases methane and carbon dioxide: landfills emit the equivalent greenhouse gases of 35 million cars every year. New uses of biogas will also help lower costs for making carbon-neutral biofuels, since biofuel production also generates waste that can be turned into biogas.« less

76 FR 80451 - Commercial and Industrial Solid Waste Incineration Units: Reconsideration and Proposed Amendments...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-23

... wastes ERUs were designed to burn. Energy Recovery Units (i.e., units that would be boilers and process... and 241 Commercial and Industrial Solid Waste Incineration Units: Reconsideration and Proposed... 2060-AR15 and 2050-AG44 Commercial and Industrial Solid Waste Incineration Units: Reconsideration and...

Development of high-performance supercapacitor electrode derived from sugar industry spent wash waste.

PubMed

Mahto, Ashesh; Gupta, Rajeev; Ghara, Krishna Kanta; Srivastava, Divesh N; Maiti, Pratyush; D, Kalpana; Rivera, Paul-Zavala; Meena, R; Nataraj, S K

2017-10-15

This study aims at developing supercapacitor materials from sugar and distillery industry wastes, thereby mediating waste disposal problem through reuse. In a two-step process, biomethanated spent wash (BMSW) was acid treated to produce solid waste sludge and waste water with significantly reduced total organic carbon (TOC) and biological oxygen demand (BOD) content. Further, waste sludge was directly calcined in presence of activating agent ZnCl 2 in inert atmosphere resulting in high surface area (730-900m 2 g -1 ) carbon of unique hexagonal morphology. Present technique resulted in achieving two-faceted target of liquid-solid waste remediation and production of high-performance carbon material. The resulted high surface area carbon was tested in both three and two electrode systems. Electrochemical tests viz. cyclic voltammetry, galvanostatic charge-discharge and impedance measurement were carried out in aqueous KOH electrolyte yielding specific capacitance as high as 120Fg -1 , whereas all solid supercapacitor devised using PVA/H 3 PO 4 polyelectrolyte showed stable capacitance of 105Fg -1 at 0.2Ag -1 . The presence of transition metal particles and hetero-atoms on carbon surface were confirmed by XPS, EDX and TEM analysis which enhanced the conductivity and imparted pseudocapacitance to some extent into the working electrode. The present study successfully demonstrated production of high-performance electrode material from dirtiest wastewater making process green, sustainable and economically viable. Copyright © 2017. Published by Elsevier B.V.

Pineapple peel wastes as a potential source of antioxidant compounds

NASA Astrophysics Data System (ADS)

Saraswaty, V.; Risdian, C.; Primadona, I.; Andriyani, R.; Andayani, D. G. S.; Mozef, T.

2017-03-01

Indonesia is a large pineapple (Ananas comosus) producing country. Food industries in Indonesia processed this fruit for new products and further resulted wastes of which cause an environmental problems. Approximately, one pineapple fruit total weight is 400 gr of which 60 g is of peel wastes. In order to reduce such pineapple peel wastes (PPW), processing to a valuable product using an environmentally friendly technique is indispensable. PPW contained phenolic compound, ferulic acid, and vitamin A and C as antioxidant. This study aimed to PPW using ethanol and water as well as to analyze its chemical properties. Both dried and fresh PPW were extracted using mixtures of ethanol and water with various concentrations ranging from 15 to 95% (v/v) at room temperature for 24 h. The chemical properties, such as antioxidant activity, total phenolic content (Gallic acid equivalent/GAE), and total sugar content were determined. The results showed that the range of Inhibition Concentration (IC)50 value as antioxidant activity of extracts from dried and fresh PPW were in the range of 0.8±0.05 to 1.3±0.09 mg.mL-1 and 0.25±0.01 to 0.59±0.01 mg.mL-1, respectively, with the highest antioxidant activity was in water extract. The highest of total phenolic content of 0.9 mg.g-1 GAE, was also found in water extract.

Volatile fatty acids production from anaerobic treatment of cassava waste water: effect of temperature and alkalinity.

PubMed

Hasan, Salah Din Mahmud; Giongo, Citieli; Fiorese, Mônica Lady; Gomes, Simone Damasceno; Ferrari, Tatiane Caroline; Savoldi, Tarcio Enrico

2015-01-01

The production of volatile fatty acids (VFAs), intermediates in the anaerobic degradation process of organic matter from waste water, was evaluated in this work. A batch reactor was used to investigate the effect of temperature, and alkalinity in the production of VFAs, from the fermentation of industrial cassava waste water. Peak production of total volatile fatty acids (TVFAs) was observed in the first two days of acidogenesis. A central composite design was performed, and the highest yield (3400 mg L(-1) of TVFA) was obtained with 30°C and 3 g L(-1) of sodium bicarbonate. The peak of VFA was in 45 h (pH 5.9) with a predominance of acetic (63%) and butyric acid (22%), followed by propionic acid (12%). Decreases in amounts of cyanide (12.9%) and chemical oxygen demand (21.6%) were observed, in addition to the production of biogas (0.53 cm(3) h(-1)). The process was validated experimentally and 3400 g L(-1) of TVFA were obtained with a low relative standard deviation.

Meat, Fish, and Poultry Processing Wastes.

ERIC Educational Resources Information Center

Litchfield, J. H.

1978-01-01

Presents a literature review of industrial wastes, covering publications of 1976-77. This review includes studies on: (1) meat industry wastes; (2) fish-processing waste treatment; and (3) poultry-processing waste treatment. A list of 76 references is also presented. (HM)

Plasmachemical degradation of azo dyes by humid air plasma: Yellow Supranol 4 GL, Scarlet Red Nylosan F3 GL and industrial waste.

PubMed

Abdelmalek, F; Gharbi, S; Benstaali, B; Addou, A; Brisset, J L

2004-05-01

A recent non-thermal plasma technique (i.e., a gliding arc discharge which generates reactive species at atmospheric pressure) is tested for pollution abatement of dyes dispersed in synthetic solutions and industrial effluents. Yellow Supranol 4 GL (YS) and Scarlet Red Nylosan F3 GL (SRN) are toxic synthetic dyes widely used in the Algerian textile industry and frequently present in liquid wastes of manufacture plants. Classical removal treatment processes are not efficient enough, so that the presence of dyes in liquid effluents may cause serious environmental problems, in connection with reusing waste waters for irrigation. The degradation processes achieved by the oxidising species formed in the plasma are followed by UV/VIS spectroscopy and by chemical oxygen demand measurements. They are almost complete (i.e., 92.5% for YS and 90% for dilute SRN) and rapidly follow pseudo-first-order laws, with overall estimated rate constants 3 x 10(-4) and 4 x 10(-4)s-1 for YS and SRN, respectively. The degradation rate constant for the industrial mixture (i.e., k = 1.45 x 10(-3)s-1) is a mean value for two consecutive steps (210(-3) and 6 x 10(-5)s-1) measured at the absorption peaks of the major constituent dyes, YS and SRN.

Metal pollution loading, Manzalah lagoon, Nile delta, Egypt: Implications for aquaculture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Siegel, F.R.; Slaboda, M.L.; Stanley, D.J.

1994-03-01

High cultural enrichment factors are found for Hg (13 x), Pb (22.1 x), and other potentially toxic metals (e.g., Sn, Zn, Cu, Ag) in the upper 20 cm of sediment cores from the southeastern Ginka subbasin of Manzalah lagoon, Nile delta, Egypt. Cores from other areas of the lagoon show little metal loading. Metal loading followed the closure of the Aswan High Dam, the availability of abundant cheap electricity, and the development of major power-based industries. Industrial wastes containing potentially toxic metals are dumped into the Nile delta drain system. The load carried by Bahr El-Baqar drain discharges into themore » Ginka subbasin, which acts as a sink and results in metal loading of the sediment deposited there. Further development of aquaculture in this subbasin, of food-stuff agriculture on recently reclaimed lagoon bottom, or where irrigation waters come from Bahr El-Baqar drain or its discharge should be halted or strictly limited until potentially toxic metals in the drain waters and sediment are removed and polluted input drastically reduced. This environmental assessment of heavy metals in aquaculture or agriculture development should extend to other waterbodies in the northern Nile delta, particularly Idku lagoon and Lake Mariut, where industrial metal-bearing wastes discharge into the waterbodies. 21 refs., 7 figs., 3 tabs.« less

Effects of solid-liquid separation and storage on monensin attenuation in dairy waste management systems.

PubMed

Hafner, Sarah C; Watanabe, Naoko; Harter, Thomas; Bergamaschi, Brian A; Parikh, Sanjai J

2017-04-01

Environmental release of veterinary pharmaceuticals has been of regulatory concern for more than a decade. Monensin is a feed additive antibiotic that is prevalent throughout the dairy industry and is excreted in dairy waste. This study investigates the potential of dairy waste management practices to alter the amount of monensin available for release into the environment. Analysis of wastewater and groundwater from two dairy farms in California consistently concluded that monensin is most present in lagoon water and groundwater downgradient of lagoons. Since the lagoons represent a direct source of monensin to groundwater, the effect of waste management, by mechanical screen separation and lagoon aeration, on aqueous monensin concentration was investigated through construction of lagoon microcosms. The results indicate that monensin attenuation is not improved by increased solid-liquid separation prior to storage in lagoons, as monensin is rapidly desorbed after dilution with water. Monensin is also shown to be easily degraded in lagoon microcosms receiving aeration, but is relatively stable and available for leaching under typical anaerobic lagoon conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of solid-liquid separation and storage on monensin attenuation in dairy waste management systems

USGS Publications Warehouse

Hafner, Sarah C.; Watanabe, Naoko; Harter, Thomas; Bergamaschi, Brian; Parikh, Sanjai J.

2017-01-01

Environmental release of veterinary pharmaceuticals has been of regulatory concern for more than a decade. Monensin is a feed additive antibiotic that is prevalent throughout the dairy industry and is excreted in dairy waste. This study investigates the potential of dairy waste management practices to alter the amount of monensin available for release into the environment. Analysis of wastewater and groundwater from two dairy farms in California consistently concluded that monensin is most present in lagoon water and groundwater downgradient of lagoons. Since the lagoons represent a direct source of monensin to groundwater, the effect of waste management, by mechanical screen separation and lagoon aeration, on aqueous monensin concentration was investigated through construction of lagoon microcosms. The results indicate that monensin attenuation is not improved by increased solid-liquid separation prior to storage in lagoons, as monensin is rapidly desorbed after dilution with water. Monensin is also shown to be easily degraded in lagoon microcosms receiving aeration, but is relatively stable and available for leaching under typical anaerobic lagoon conditions.

Contribution of precursor compounds to the release of per- and polyfluoroalkyl substances (PFASs) from waste water treatment plants (WWTPs).

PubMed

Eriksson, Ulrika; Haglund, Peter; Kärrman, Anna

2017-11-01

Per- and polyfluoroalkyl substances (PFASs) are ubiquitous in sludge and water from waste water treatment plants, as a result of their incorporation in everyday products and industrial processes. In this study, we measured several classes of persistent PFASs, precursors, transformation intermediates, and newly identified PFASs in influent and effluent sewage water and sludge from three municipal waste water treatment plants in Sweden, sampled in 2015. For sludge, samples from 2012 and 2014 were analyzed as well. Levels of precursors in sludge exceeded those of perfluoroalkyl acids and sulfonic acids (PFCAs and PFSAs), in 2015 the sum of polyfluoroalkyl phosphoric acid esters (PAPs) were 15-20ng/g dry weight, the sum of fluorotelomer sulfonic acids (FTSAs) was 0.8-1.3ng/g, and the sum of perfluorooctane sulfonamides and ethanols ranged from non-detected to 3.2ng/g. Persistent PFSAs and PFCAs were detected at 1.9-3.9ng/g and 2.4-7.3ng/g dry weight, respectively. The influence of precursor compounds was further demonstrated by an observed substantial increase for a majority of the persistent PFCAs and PFSAs in water after waste water treatment. Perfluorohexanoic acid (PFHxA), perfluorooctanoic acid (PFOA), perfluorohexane sulfonic acid (PFHxS), and perfluorooctane sulfonic acid (PFOS) had a net mass increase in all WWTPs, with mean values of 83%, 28%, 37% and 58%, respectively. The load of precursors and intermediates in influent water and sludge combined with net mass increase support the hypothesis that degradation of precursor compounds is a significant contributor to PFAS contamination in the environment. Copyright © 2017. Published by Elsevier B.V.

Statistical Evaluation and Optimization of Factors Affecting the Leaching Performance of Copper Flotation Waste

PubMed Central

Çoruh, Semra; Elevli, Sermin; Geyikçi, Feza

2012-01-01

Copper flotation waste is an industrial by-product material produced from the process of manufacturing copper. The main concern with respect to landfilling of copper flotation waste is the release of elements (e.g., salts and heavy metals) when in contact with water, that is, leaching. Copper flotation waste generally contains a significant amount of Cu together with trace elements of other toxic metals, such as Zn, Co, and Pb. The release of heavy metals into the environment has resulted in a number of environmental problems. The aim of this study is to investigate the leaching characteristics of copper flotation waste by use of the Box-Behnken experimental design approach. In order to obtain the optimized condition of leachability, a second-order model was examined. The best leaching conditions achieved were as follows: pH = 9, stirring time = 5 min, and temperature = 41.5°C. PMID:22629194

Statistical evaluation and optimization of factors affecting the leaching performance of copper flotation waste.

PubMed

Coruh, Semra; Elevli, Sermin; Geyikçi, Feza

2012-01-01

Copper flotation waste is an industrial by-product material produced from the process of manufacturing copper. The main concern with respect to landfilling of copper flotation waste is the release of elements (e.g., salts and heavy metals) when in contact with water, that is, leaching. Copper flotation waste generally contains a significant amount of Cu together with trace elements of other toxic metals, such as Zn, Co, and Pb. The release of heavy metals into the environment has resulted in a number of environmental problems. The aim of this study is to investigate the leaching characteristics of copper flotation waste by use of the Box-Behnken experimental design approach. In order to obtain the optimized condition of leachability, a second-order model was examined. The best leaching conditions achieved were as follows: pH = 9, stirring time = 5 min, and temperature = 41.5 °C.

Water quality assessment in streams and wastewater treatment plants of Blantyre, Malawi

NASA Astrophysics Data System (ADS)

Sajidu, S. M. I.; Masamba, W. R. L.; Henry, E. M. T.; Kuyeli, S. M.

The population of the city of Blantyre has grown rapidly over the past few years without keeping pace with the national economy. The most visibly affected areas of this increase in population are access to adequate clean water, solid waste collection and disposal, sanitary and sewerage facilities. The objective of this study was to evaluate water quality in streams and wastewater treatment plants (WWTP) in the City of Blantyre, Malawi. Study locations included Limbe WWTP, Soche WWTP, Limbe, Mudi and Nasolo streams. Water samples were collected by grab sampling technique in February 2005. Phosphates, nitrates and sulphates were determined by vanadomolybdophosphoric acid colorimetric, salicylate colorimetric and turbidimetric methods, respectively. Metals were analysed using atomic absorption spectroscopy. Concentrations of lead, cadmium, iron, manganese, zinc, chromium and nickel were much higher than the World Health safe limits for drinking water in all the sampled streams after they had passed through industrial areas. Nitrates and sulphates concentrations at all sampling points were found to be lower than the safe limits for drinking water of 50 mg/l and 250 mg/l, respectively. However, phosphate concentrations were above the safe limit of 0.5 mg/l. It was also observed that biochemical oxygen demand (BOD 5) levels were above the World Health Organisation limit of 20 mg/l at all sites except Mudi and Limbe streams before passing through industrial areas. This was an indication of pollution in the streams. Values of pH and total dissolved solids (TDS) were within the recommended standards. The results suggest that streams in Blantyre City get polluted by heavy metals and nutrients which could be due to uncontrolled industrial waste disposal, vehicular emissions and agricultural activities. Regular monitoring of the water quality and enforcement of environmental protection laws are needed in order to control pollution in the city.

A study on the dewatering of industrial waste sludge by fry-drying technology.

PubMed

Ohm, Tae-In; Chae, Jong-Seong; Kim, Jeong-Eun; Kim, Hee-Kyum; Moon, Seung-Hyun

2009-08-30

In sludge treatment, drying sludge using typical technology with high water content to a water content of approximately 10% is always difficult because of adhesive characteristics of sludge. Many methods have been applied, including direct and indirect heat drying, but these approaches of reducing water content to below 40% after drying is very inefficient in energy utilization of drying sludge. In this study, fry-drying technology with a high heat transfer coefficient of approximately 500 W/m(2) degrees C was used to dry industrial wastewater sludge. Also waste oil was used in the fry-drying process, and because the oil's boiling point is between 240 and 340 degrees C and the specific heat is approximately 60% of that of water. In the fry-drying system, the sludge is input by molding it into a designated form after heating the waste oil at temperatures between 120 and 170 degrees C. At these temperatures, the heated oil rapidly evaporates the water contained in the sludge, leaving the oil itself. After approximately 10 min, the water content of the sludge was less than 10%, and its heating value surpassed 5300 kcal/kg. Indeed, this makes the organic sludge appropriate for use as a solid fuel. The wastewater sludge used in this study was the designated waste discharged from chemical, leather and plating plants. These samples varied in characteristics, especially with regard to heavy metal concentration. After drying the three kinds of wastewater sludge at oil temperatures 160 degrees C for 10 min, it was found that the water content in the sludge from the chemical, leather, and plating plants reduced from 80.0 to 5.5%, 81.6 to 1.0%, and 65.4 to 0.8%, respectively. Furthermore, the heat values of the sludge from the chemical, leather, and plating plants prior to fry-drying were 217, 264, and 428 kcal/kg, respectively. After drying, these values of sludge increased to 5317, 5983 and 6031 kcal/kg, respectively. The heavy metals detected in the sludge after drying were aluminum, lead, zinc, mercury, and cadmium. Most importantly, if the dried sludge is used as a solid fuel, these heavy metals can be collected from the dust collector after combustion.

Injection of acidic industrial waste into the Floridan Aquifer near Belle Glade, Florida: upward migration and geochemical interactions, 1973-75

USGS Publications Warehouse

McKenzie, Donald J.

1976-01-01

In 1966, a furfural plant at Belle Glade, Florida, began injecting hot, acidic liquid waste into the saline, water-filled lower part of the Floridan aquifer, between the depths of 1 ,495-1,939 feet. The beds above and below the injection zone were subjected to attack by the acid waste. By 1969, effects of the waste were detected in the water of the well monitoring the upper part of the Floridan aquifer at 1,400 feet. The disposal well was deepened late in 1971 to 2,242 feet in an attempt to stop the upward migration of waste. The results of research investigations by the U.S. Geological Survey during 1966-73 indicated that the waste continued to move upward and laterally. This investigated, continued by the U.S. Geological Survey in 1973-1975, shows that the remedial actions of repairing the disposal well liner and injecting periodically into the deep monitor well at 2,060 feet failed to contain the wastes within the lower part of the Floridan aquifer. The data collected by the Survey are supported by the owner 's chemical-oxygen-demand and pH determinations. A hydraulic connection between the injection zone and the overlying monitoring zone is implied. Plans call for injecting into deepter strata. (Woodard-USGS)

Toxicity screening of waste products using cell culture techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petitmermet, M.; Favre, A.; Shah, B.

1995-12-31

More than 600,000 tons of residue from waste incineration plants is produced in Switzerland each year. These residues are slag, fly ashes, and residues from extended flue gas cleaning. Because they are contaminated with heavy metals, they have to be deposited in appropriate landfills. Due to the increasing amount of municipal and industrial waste and the decreasing amount of disposal sites, additional treatment of waste and its by-products is becoming more and more important. To decrease the amount of residuals to be deposited, the heavy metal content of the residues has to be reduced by physical, chemical, or biological methodsmore » to acceptably low levels to obtain products suitable for reuse in the construction industry. The cell reactions due to the presence of residues and their extracts were studied using quantitative and qualitative methods. The results of the applied cell culture techniques showed that fly ash was much more cytotoxic than slag. This finding correlates with the chemical analysis. The washed samples were again less cytotoxic than their corresponding unwashed samples due to the lack of water-soluble compounds. The very sensitive response of the cell cultures to toxic substances was used to classify and validate the applied treatment methods.« less

Production of novel microbial flocculants by Klebsiella sp. TG-1 using waste residue from the food industry and its use in defecating the trona suspension.

PubMed

Liu, Zhan-Ying; Hu, Zhi-Quan; Wang, Tao; Chen, Yan-Ying; Zhang, Jianbin; Yu, Jing-Ran; Zhang, Tong; Zhang, Yong-Feng; Li, Yong-Li

2013-07-01

A microbial-flocculants-producing (MBF-producing) bacterium, named TG-1, was isolated from waste water of a starch factory, and identified as Klebsiella sp. TG-1. The microbial flocculants (MBF) produced by TG-1, named as MBF-TG-1, was applied to defecating the strong basic trona suspension in the trona industry. After optimizing medium and culturing conditions with single-factor and orthogonal designs, the highest flocculation rate of 86.9% was achieved. Chemical analysis showed that the purified microbial flocculants (MBF-TG-1) was mainly composed of polysaccharides (84.6%), with a small amount of protein or amino acid (11.1%). Bridging mechanism was supposed as the main flocculation mechanism by analyzing the flocculation process and the biochemistry properties of MBF-TG-1. The high flocculation rate (84%) was also achieved with a low-cost medium (the solid residue of tofu production from food industry). Copyright © 2013 Elsevier Ltd. All rights reserved.

Supercritical water oxidation for the destruction of toxic organic wastewaters: a review.

PubMed

Veriansyah, Bambang; Kim, Jae-Duck

2007-01-01

The destruction of toxic organic wastewaters from munitions demilitarization and complex industrial chemical clearly becomes an overwhelming problem if left to conventional treatment processes. Two options, incineration and supercritical water oxidation (SCWO), exist for the complete destruction of toxic organic wastewaters. Incinerator has associated problems such as very high cost and public resentment; on the other hand, SCWO has proved to be a very promising method for the treatment of many different wastewaters with extremely efficient organic waste destruction 99.99% with none of the emissions associated with incineration. In this review, the concepts of SCWO, result and present perspectives of application, and industrial status of SCWO are critically examined and discussed.

Therma motor

DOEpatents

Kandarian, R.

The disclosure is directed to a thermal motor utilizing two tapered prestressed parallel adjacent cylinders lengthwise disposed about one third in a coolant. Heat is applied to contacting portions of the cylinders outside the coolant to cause them to deform and turn. Heat sources such as industrial waste heat, geothermal hot water, solar radiation, etc. can be used.

Studies on urban drinking water quality in a tropical zone.

PubMed

Mudiam, Mohana Krishna Reddy; Pathak, S P; Gopal, K; Murthy, R C

2012-01-01

Anthropogenic activities associated with industrialization, agriculture and urbanization have led to the deterioration in water quality due to various contaminants. To assess the status of urban drinking water quality, samples were collected from the piped supplies as well as groundwater sources from different localities of residential, commercial and industrial areas of Lucknow City in a tropical zone of India during pre-monsoon for estimation of coliform and faecal coliform bacteria, organochlorine pesticides (OCPs) and heavy metals. Bacterial contamination was found to be more in the samples from commercial areas than residential and industrial areas. OCPs like α,γ-hexachlorocyclohexane and 1,1 p,p-DDE {dichloro-2, 2-bis(p-chlorophenyl) ethene)} were found to be present in most of the samples from study area. The total organochlorine pesticide levels were found to be within the European Union limit (0.5 μg/L) in most of the samples. Most of the heavy metals estimated in the samples were also found to be within the permissible limits as prescribed by World Health Organization for drinking water. Thus, these observations show that contamination of drinking water in urban areas may be mainly due to municipal, industrial and agricultural activities along with improper disposal of solid waste. This is an alarm to safety of public health and aquatic environment in tropics.

The sensitivity and reproducibility of the zebrafish (Danio rerio) embryo test for the screening of waste water quality and for testing the toxicity of chemicals.

PubMed

Lahnsteiner, Franz

2008-07-01

The sensitivity of the zebrafish embryo test, a test proposed for routine waste water control, was compared with the acute fish toxicity test, in the determination of six types of waste water and ten different chemicals. The waste water was sampled from the following industrial processes: paper and cardboard production, hide tanning, metal galvanisation, carcass treatment and utilisation, and sewage treatment. The chemicals tested were: dimethylacetamide, dimethylsulphoxide, cadmium chloride, cyclohexane, hydroquinone, mercuric chloride, nickel chloride, nonylphenol, resmethrin and sodium nitrite. For many of the test substances, the zebrafish embryo test and the acute fish toxicity test results showed high correlations. However, there were certain environmentally-relevant substances for which the results of the zebrafish embryo test and the acute fish toxicity test differed significantly, up to 10,000-fold (Hg(2+) > 150-fold difference; NO(2)(-) > 300-fold; Cd(2+) > 200-fold; resmethrin > 10,000-fold). For the investigated waste water samples and chemicals, the survival rate of the zebrafish embryos showed high variations between different egg samples, within the range of the EC50 concentration. Subsequently, 5-6 parallel assays were deemed to be the appropriate number necessary for the precise evaluation of the toxicity of the test substances. Also, it was found that the sensitivities of different ontogenetic stages to chemical exposure differed greatly. During the first 12 hours after fertilisation (4-cell stage to the 5-somite stage), the embryos reacted most sensitively to test substance exposure, whereas the later ontogenetic stages showed only slight or no response, indicating that the test is most sensitive during the first 24 hours post-fertilisation.

Forecasting the Amount of Waste-Sewage Water Discharged into the Yangtze River Basin Based on the Optimal Fractional Order Grey Model.

PubMed

Li, Shuliang; Meng, Wei; Xie, Yufeng

2017-12-23

With the rapid development of the Yangtze River economic belt, the amount of waste-sewage water discharged into the Yangtze River basin increases sharply year by year, which has impeded the sustainable development of the Yangtze River basin. The water security along the Yangtze River basin is very important for China, It is something aboutwater security of roughly one-third of China's population and the sustainable development of the 19 provinces, municipalities and autonomous regions among the Yangtze River basin. Therefore, a scientific prediction of the amount of waste-sewage water discharged into Yangtze River basin has a positive significance on sustainable development of industry belt along with Yangtze River basin. This paper builds the fractional DWSGM(1,1)(DWSGM(1,1) model is short for Discharge amount of Waste Sewage Grey Model for one order equation and one variable) model based on the fractional accumulating generation operator and fractional reducing operator, and calculates the optimal order of "r" by using particle swarm optimization(PSO)algorithm for solving the minimum average relative simulation error. Meanwhile, the simulation performance of DWSGM(1,1)model with the optimal fractional order is tested by comparing the simulation results of grey prediction models with different orders. Finally, the optimal fractional order DWSGM(1,1)grey model is applied to predict the amount of waste-sewage water discharged into the Yangtze River basin, and corresponding countermeasures and suggestions are put forward through analyzing and comparing the prediction results. This paper has positive significance on enriching the fractional order modeling method of the grey system.

Current and potential uses of bioactive molecules from marine processing waste.

PubMed

Suleria, Hafiz Ansar Rasul; Masci, Paul; Gobe, Glenda; Osborne, Simone

2016-03-15

Food industries produce huge amounts of processing waste that are often disposed of incurring expenses and impacting upon the environment. For these and other reasons, food processing waste streams, in particular marine processing waste streams, are gaining popularity amongst pharmaceutical, cosmetic and nutraceutical industries as sources of bioactive molecules. In the last 30 years, there has been a gradual increase in processed marine products with a concomitant increase in waste streams that include viscera, heads, skins, fins, bones, trimmings and shellfish waste. In 2010, these waste streams equated to approximately 24 million tonnes of mostly unused resources. Marine processing waste streams not only represent an abundant resource, they are also enriched with structurally diverse molecules that possess a broad panel of bioactivities including anti-oxidant, anti-coagulant, anti-thrombotic, anti-cancer and immune-stimulatory activities. Retrieval and characterisation of bioactive molecules from marine processing waste also contributes valuable information to the vast field of marine natural product discovery. This review summarises the current use of bioactive molecules from marine processing waste in different products and industries. Moreover, this review summarises new research into processing waste streams and the potential for adoption by industries in the creation of new products containing marine processing waste bioactives. © 2015 Society of Chemical Industry.