Crew operations

NASA Technical Reports Server (NTRS)

1971-01-01

The requirements for the activities involved, and the procedures used by the crew in the operations of the modular space station are presented. All crew-related characteristics of the station and its operations are indicated. The interior configuration and arrangement of each of the space station modules, the facilities and equipment in the module and their operation are described as related to crew habitability. The crew activities and procedures involved in the operation of the station in the accomplishment of its primary mission are defined. The operations involved in initial station buildup, and the on-orbit operation and maintenance of the station and its subsystems to support the experimental program are included. A general description of experiment operations is also given.

Effect of soil properties on Hydraulic characteristics under subsurface drip irrigation

NASA Astrophysics Data System (ADS)

Fan, Wangtao; Li, Gang

2018-02-01

Subsurface drip irrigation (SDI) is a technique that has a high potential in application because of its high efficiency in water-saving. The hydraulic characteristics of SDI sub-unit pipe network can be affected by soil physical properties as the emitters are buried in soils. The related research, however, is not fully explored. The laboratory tests were carried out in the present study to determine the effects of hydraulic factors including operating pressure, initial soil water content, and bulk density on flow rate and its sensitivity to each hydraulic factor for two types of SDI emitters (PLASSIM emitter and Heping emitter). For this purpose, three soils with contrasting textures (i.e., light sand, silt loam, and light clay) were repacked with two soil bulk density (1.25 and1.40 g cm-3) with two initial soil water content (12% and 18%) in plexiglass columns with 40 cm in diameter and 40 cm in height. Drip emitters were buried at depth of 20 cm to measure the flow rates under seven operating pressures (60, 100, 150, 200, 250, 300, and 370 kPa). We found that the operating pressure was the dominating factor of flow rate of the SDI emitter, and flow rate increased with the increase of operating pressure. The initial soil water content and bulk density also affected the flow rate, and their effects were the most notable in the light sand soil. The sensitivity of flow rate to each hydraulic factor was dependent on soil texture, and followed a descending order of light sand>silt loam>light clay for both types of emitters. Further, the sensitivity of flow rate to each hydraulic factor decreased with the increase of operating pressure, initial soil water content, and bulk density. This study may be used to guide the soil specific-design of SDI emitters for optimal water use and management.

5 CFR 960.107 - Authorized activities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... coordinated approaches to the development and operation of programs that have common characteristics; (3) communicate management initiatives and other concerns from Washington to the field to achieve better mutual... serve as an instrument of outreach for the national headquarters of the Executive Branch to Executive...

5 CFR 960.107 - Authorized activities.

Code of Federal Regulations, 2011 CFR

2011-01-01

... coordinated approaches to the development and operation of programs that have common characteristics; (3) communicate management initiatives and other concerns from Washington to the field to achieve better mutual... serve as an instrument of outreach for the national headquarters of the Executive Branch to Executive...

Evaluation of indeterminacy of initial data for cad system of electric engine suspension

NASA Astrophysics Data System (ADS)

Antipin, D. Ya; Izmerov, O. V.; Shorokhov, S. G.; Nadtochey, D. G.

2018-03-01

The research of the variants of the suspension of the traction electric motor of diesel locomotives was performed. It was found that the method of designing the suspension does not take into consideration the possible changes of the characteristics of the parts in operation conditions. Variants of the suspension design were proposed and patented, which provide the work reliability despite the operating conditions.

Changes in the performance characteristics of a GaAs near infrared light emitting diode when exposed to various current and thermal stresses

NASA Technical Reports Server (NTRS)

Thomas, E. F., Jr.

1974-01-01

The changes that occurred in the optical and electrical characteristics of a near infrared, GaAs light emitting diode, when operated under various levels and combinations of current and thermal stresses are discussed. A total of forty parts were operated for two thousand hours under eight different sets of dc current and ambient temperature conditions. Degradation in the radiant optical power of these devices was thirty-four percent when operated at their rated current and an ambient temperature of 298K (25 C). Derating the current and/or the thermal stress reduced the degradation of this parameter in approximately a linear manner. All degraded devices behaved similarly, exhibiting rapid nonlinear degradation followed by a gradual linear degradation and finally a period of stable operation. An attempt was made to correlate initial device condition to degradation during stress testing, but met with little success.

Considerations for Architecture Level Trade Studies for Environmental Sensors

NASA Technical Reports Server (NTRS)

Peterson, Craig

2010-01-01

Comparisons of key characteristics of environmental sensors such as technology readiness levels, mass, power, volume, and detection capabilities are essential for initial trade studies to determine likely candidates for further development and evaluation. However, these trade studies only provide part of the information necessary to make selection decisions. Ultimately, the sensors must be judged based on the overall system architectures and operational scenarios for which they are intended. This means that additional characteristics, such as architectural needs for redundancy, operational lifetime, ability to maintain calibration, and repair and replacement strategies, among others, must also be considered. Given that these characteristics can be extremely time-consuming and costly to obtain, careful planning is essential to minimize the effort involved. In this paper, an approach is explored for determining an effective yet comprehensive set of architecture level trades which is minimally impacted by the inevitable changes in operational (mission) scenarios. The approach will also identify and integrate the various facilities and opportunities required to obtain the desired architecture level trade information.

Assembly and Initial Analysis of a Database of the Characteristics of Fixed-Wing Unmanned Aircraft Systems

DTIC Science & Technology

2014-11-01

sea level (evaluated for turbojet- and turbofan -powered UAVs and targets only) R range (km) ferryR ferry range (km) radiusR mission radius (km...operating airspeed for manned turbofan -powered aircraft, and a power law for birds derived by Alerstam et al. [22...UAVs in the Database; and ratio of operating to maximum airspeed for turbojet- or turbofan -powered UAVs with mmax > 103 kg

Space shuttle SRM plume expansion sensitivity analysis. [flow characteristics of exhaust gases from solid propellant rocket engines

NASA Technical Reports Server (NTRS)

Smith, S. D.; Tevepaugh, J. A.; Penny, M. M.

1975-01-01

The exhaust plumes of the space shuttle solid rocket motors can have a significant effect on the base pressure and base drag of the shuttle vehicle. A parametric analysis was conducted to assess the sensitivity of the initial plume expansion angle of analytical solid rocket motor flow fields to various analytical input parameters and operating conditions. The results of the analysis are presented and conclusions reached regarding the sensitivity of the initial plume expansion angle to each parameter investigated. Operating conditions parametrically varied were chamber pressure, nozzle inlet angle, nozzle throat radius of curvature ratio and propellant particle loading. Empirical particle parameters investigated were mean size, local drag coefficient and local heat transfer coefficient. Sensitivity of the initial plume expansion angle to gas thermochemistry model and local drag coefficient model assumptions were determined.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frederick, P.R.

The purpose of this research was to provide a handbook on Project PETROL RAM and its ideas for enhancing the base-level fuels operations. This handbook is to serve as an introduction and reference guide to the components, characteristics, and capabilities of the proposed initiative. In preparing this handbook, available information on the structure, operations, and procedures of a typical base Fuels Management Branch was gathered, then condensed and simplified. For added depth and understanding, personal interviews with personnel involved in the design and development of this project were conducted. The research resulted in a handbook that describes, in simplified terminology,more » the different systems which are being developed under the Project PETROL RAM initiative.« less

Dynamic characteristics of single crystal SSME blades

NASA Technical Reports Server (NTRS)

Moss, L. A.; Smith, T. E.

1987-01-01

The Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP) blades are currently manufactured using a directionally solidified (DS) material, MAR-M-246+Hf. However, a necessity to reduce the occurrence of fatigue cracking within the DS blades has lead to an interest in the use of a single crystal (SC) material, PWA-1480. A study was initiated to determine the dynamic characteristics of the HPFTP blades made of SC material and find possible critical engine order excitations. This study examined both the first and second stage drive turbine blades of the HPFTP. The dynamic characterization was done analytically as well as experimentally. The analytical study examined the SC first stage HPFTP blade dynamic characteristics under typical operating conditions. The blades were analyzed using MSC/NASTRAN and a finite element model. Two operating conditions, 27500 RPM and 35000 RPM, were investigated.

Suicide rates in European OECD nations converged during the period 1990-2010.

PubMed

Bremberg, Sven G

2017-05-01

The aim of this study was to investigate, with multiple regression analyses, the effect of selected characteristics on the rate of decrease of suicide rates in 21 OECD (Organisation for Economic Co-operation and Development) nations over the period 1990-2010, with initial levels of suicide rates taken into account. The rate of decrease seems mainly (83%) to be determined by the initial suicide rates in 1990. In nations with relatively high initial rates, the rates decreased faster. The suicide rates also converged. The study indicates that beta convergence alone explained most of the cross-national variations.

Investigating NWP initialization sensitivities in heavy precipitation events

NASA Astrophysics Data System (ADS)

Frediani, M. E. B.; Anagnostou, E. N.; Papadopoulos, A.

2010-09-01

This study aims to investigate the effect of different types of model initialization applied to extreme storms simulations. Storms with extreme precipitation can usually produce flash floods that cause several damages to the society. Lives and property are destroyed from the landslides when they could be speared if forecasted a few hours in advance. The forecasts depend on several factors; among them the initialization fields play an important role. These fields are the starting point for the simulation and therefore it controls the quality of the forecast. This study evaluates the sensitivities of WRF to the initialization from two perspectives, (1) resolution and (2) initial atmospheric fields. Two storms that lead to flash flood are simulated. The first one happened in Northeast Italy in 04/09/2009 (NI), and the second in Germany, in 02/06/2008 (GE). These storms present contrasting characteristics, NI was a maritime originated storm enhanced by local orography while GE was a typical summer convection. Three different sources of atmospheric fields defining the initial conditions are applied: (a) ECMWF operational analysis at resolution of 0.25 deg, (b) GFS operational analysis at 0.5deg and (c) LAPS analysis at ~15km, produced operationally at HCMR. The rainfall forecasted is compared against in situ ground radar and surface rain gauges observations through a set of quantitative precipitation forecast scores.

The Case Mix of Patients Presenting with Full-Thickness Macular Holes and Progression before Surgery: Implications for Optimum Management.

PubMed

Madi, Haifa A; Dinah, Christiana; Rees, Jon; Steel, David H W

2015-01-01

Analysis of pre-operative spectral domain optical coherence tomography (SD-OCT) characteristics of full-thickness macular holes (FTMH) and effect on optimum management. We retrospectively reviewed SD-OCT characteristics of a consecutive cohort of patients waitlisted for FTMH surgery and categorized them by current evidence-based treatments. Out of the 106 holes analysed, 36 were small, 40 medium and 30 large. Initially, 33 holes had vitreomacular adhesion (VMA). 41 holes were analysed for change in characteristics with a median duration of 8 weeks between the scans. The number of small or medium holes decreased from 20 to 6 and that of large holes doubled. The number of holes with VMA halved. Smaller hole size (p = 0.014) and being phakic (p = 0.048) were associated with a larger increase in size. The strongest predictor of hole progression into a different surgical management category was the presence of VMA. FTMH characteristics can change significantly pre-operatively and affect optimal treatment choice.

Alkaline anion exchange membrane water electrolysis: Effects of electrolyte feed method and electrode binder content

NASA Astrophysics Data System (ADS)

Cho, Min Kyung; Park, Hee-Young; Lee, Hye Jin; Kim, Hyoung-Juhn; Lim, Ahyoun; Henkensmeier, Dirk; Yoo, Sung Jong; Kim, Jin Young; Lee, So Young; Park, Hyun S.; Jang, Jong Hyun

2018-04-01

Herein, we investigate the effects of catholyte feed method and anode binder content on the characteristics of anion exchange membrane water electrolysis (AEMWE) to construct a high-performance electrolyzer, revealing that the initial AEMWE performance is significantly improved by pre-feeding 0.5 M aqueous KOH to the cathode. The highest long-term activity during repeated voltage cycling is observed for AEMWE operation in the dry cathode mode, for which the best long-term performance among membrane electrode assemblies (MEAs) featuring polytetrafluoroethylene (PTFE) binder-impregnated (5-20 wt%) anodes is detected for a PTFE content of 20 wt%. MEAs with low PTFE content (5 and 9 wt%) demonstrate high initial performance, rapid performance decay, and significant catalyst loss from the electrode during long-term operation, whereas the MEA with 20 wt% PTFE allows stable water electrolysis for over 1600 voltage cycles. Optimization of cell operating conditions (i.e., operation in dry cathode mode at an optimum anode binder content following an initial solution feed) achieves an enhanced water splitting current density (1.07 A cm-2 at 1.8 V) and stable long-term AEMWE performance (0.01% current density reduction per voltage cycle).

Investigation of hazards associated with plastic bonded starter mix manufacturing processes

NASA Technical Reports Server (NTRS)

1971-01-01

An investigation to determine the hazards potential evaluation of plastic bonded starter mix (PBSM) production processes and the application to the M18 and M7A3 grenades is reported. The investigation indicated: (1) the materials with the greatest hazards characteristics, (2) process operating stations most likely to initiate hazardous conditions, (3) the test program required to examine ignition characteristics and process hazards, and (4) the method of handling the accumulated information from testing and safety analyses.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coble, Jamie; Orton, Christopher; Schwantes, Jon

Abstract—The Multi-Isotope Process (MIP) Monitor provides an efficient approach to monitoring the process conditions in used nuclear fuel reprocessing facilities to support process verification and validation. The MIP Monitor applies multivariate analysis to gamma spectroscopy of reprocessing streams in order to detect small changes in the gamma spectrum, which may indicate changes in process conditions. This research extends the MIP Monitor by characterizing a used fuel sample after initial dissolution according to the type of reactor of origin (pressurized or boiling water reactor), initial enrichment, burn up, and cooling time. Simulated gamma spectra were used to develop and test threemore » fuel characterization algorithms. The classification and estimation models employed are based on the partial least squares regression (PLS) algorithm. A PLS discriminate analysis model was developed which perfectly classified reactor type. Locally weighted PLS models were fitted on-the-fly to estimate continuous fuel characteristics. Burn up was predicted within 0.1% root mean squared percent error (RMSPE) and both cooling time and initial enrichment within approximately 2% RMSPE. This automated fuel characterization can be used to independently verify operator declarations of used fuel characteristics and inform the MIP Monitor anomaly detection routines at later stages of the fuel reprocessing stream to improve sensitivity to changes in operational parameters and material diversions.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pickerell, D.H.; Abkowitz, M.; Tozzi, J.

The 9 papers in the report deal with the following areas: Federal operating assistance for urban mass transit; a decade of experience; transit route characteristics and headway-based reliability control; day-of-week and part-of-month variation in bus ridership; job satisfaction and transit operator recognition programs; results of a survey of muni operators; bus marketing costs: the experience of 18 section 15 reporters from 1981 to 1983; prospects for differential transit pricing in the United States; an initial analysis of total factor productivity for public-transit coordination of transportation resources: the Georgia experience; absenteeism, accidents, and attrition: part-time versus full-time bus drivers.

Comparative Performance Assessment of INTELSAT 5 Nickel Hydrogen and Nickel Cadmium Batteries

NASA Technical Reports Server (NTRS)

Cooper, D.; Ozkul, A.

1984-01-01

The first Nickel Hydrogen battery deployment onboard a commercial geosynchronous communications satellite was realized with the launch of the INTELSAT 5, Flight 6 spacecraft on 19 May 1983. The initial five spacecrafts in this series are equipped with Nickel Cadmium batteries. Based on the data available on both types of batteries, design and operational performance comparisons of INTELSAT 5 Nickel Cadmium batteries are presented. General characteristics of the INTELSAT 5 spacecraft as related to electrical-power-subsystem functions and battery operations are summarized.

Community Residences for Mentally Retarded People: A Study of Seven Community Residences.

ERIC Educational Resources Information Center

Wehbring, Kurt; Ogren, Ciele

The report describes the distinctive characteristics and styles of seven community residences for retarded children or adults and provides a comparative analysis with emphasis on common themes of successful group homes. The homes are compared in terms of original initiation of the residence; the development of the residence; operations (such as…

Bypass control valve seal and bearing life cycle test report

NASA Technical Reports Server (NTRS)

Lundback, A. V.

1972-01-01

The operating characteristics of a bypass control valve seal and bearing life cycle tests are reported. Data from the initial assembly, leak, torque, and deflection tests are included along with the cycle life test results and conclusions. The equipment involved was to be used in the nuclear engine for the rocket vehicles program.

Tier One Performance Screen Initial Operational Test and Evaluation: 2011 Interim Report

DTIC Science & Technology

2012-04-01

Alexandria, Virginia 22314 8 . PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) U. S. Army Research...DISTRIBUTION OF MOS IN THE FULL SCHOOLHOUSE DATA FILE ............ 8 TABLE 2.3. BACKGROUND AND DEMOGRAPHIC CHARACTERISTICS OF THE TOPS SAMPLES...SCHOOLHOUSE SAMPLE ....................................................................................................................B-6 TABLE B. 8

High performance low voltage organic field effect transistors on plastic substrate for amplifier circuits

NASA Astrophysics Data System (ADS)

Houin, G.; Duez, F.; Garcia, L.; Cantatore, E.; Torricelli, F.; Hirsch, L.; Belot, D.; Pellet, C.; Abbas, M.

2016-09-01

The high performance air stable organic semiconductor small molecule dinaphtho[2,3-b:2',3'-f]thieno[3,2-b]thiophene (DNTT) was chosen as active layer for field effect transistors built to realize flexible amplifier circuits. Initial device on rigid Si/SiO2 substrate showed appreciable performance with hysteresis-free characteristics. A number of approaches were applied to simplify the process, improve device performance and decrease the operating voltage: they include an oxide interfacial layer to decrease contact resistance; a polymer passivation layer to optimize semiconductor/dielectric interface and an anodized high-k oxide as dielectric layer for low voltage operation. The devices fabricated on plastic substrate yielded excellent electrical characteristics, showing mobility of 1.6 cm2/Vs, lack of hysteresis, operation below 5 V and on/off current ratio above 105. An OFET model based on variable ranging hopping theory was used to extract the relevant parameters from the transfer and output characteristics, which enabled us to simulate our devices achieving reasonable agreement with the measurements

Investigation of the Discharge Characteristics of the T6 Hollow Cathode Operating on Several Inert Gases and a Kr/Xe Mixture

NASA Astrophysics Data System (ADS)

Ahmed Rudwan, M.; Gabriel, S. B.

2002-01-01

Investigation of the discharge characteristics of the T6 hollow cathode operating on several inert Xenon is currently the propellant of choice for gridded ion thrusters. But in order to make deep space missions feasible, an increase in the Specific Impulse (SI) that these thrusters can achieve is necessary. One method of achieving this is to use a propellant with a lower atomic mass (e.g. argon), as the propellant exhaust velocity is inversely proportional to the square root of the propellant mass. However, the feasibility of operating the hollow cathode using these alternative propellants has to be demonstrated. Moreover, interest in decreasing the propellant cost in missions and ground testing (especially life tests) have led to the comprehensive discharge characterisation of several gases that will be presented in this paper. A Kr/Xe mixture in the naturally occurring ratio, for example, could offer a 15 times cost saving when compared to pure xenon and 2-3 times cost saving when compared to pure krypton. The T6 hollow cathode discharge behaviour as well as its initiation characteristics have been studied. The tests were carried out in diode configuration using a T6 hollow cathode with an enclosed keeper design employing xenon, krypton, argon and a Kr/Xe mix. The discharge initiation tests were undertaken with a view to investigate some of the factors thought to influence the starting potential such as mass flow rate and tip temperature. It was found that, for mass flow rates ranging from 0.2-1.1 mg/s and cathode tip temperatures ranging from 900-1300oC, the breakdown potential was less than 50V for argon, less than 25V for krypton, less than 21V for xenon and less than 35V for the Kr/Xe mix. The discharge initiation results were then compared to those obtained by Fearn et al. with a T5 cathode operating on mercury and with a T6 cathode utilising an open keeper design using xenon propellant. The xenon breakdown potentials were found to be lower than those obtained with an open keeper design by as much as 4V. Steady state discharge behaviour was also investigated in a range of operating conditions. Spot to plume mode transitions were observed in argon, krypton and Kr/Xe discharges for the first time.

Variable Order and Distributed Order Fractional Operators

NASA Technical Reports Server (NTRS)

Lorenzo, Carl F.; Hartley, Tom T.

2002-01-01

Many physical processes appear to exhibit fractional order behavior that may vary with time or space. The continuum of order in the fractional calculus allows the order of the fractional operator to be considered as a variable. This paper develops the concept of variable and distributed order fractional operators. Definitions based on the Riemann-Liouville definitions are introduced and behavior of the operators is studied. Several time domain definitions that assign different arguments to the order q in the Riemann-Liouville definition are introduced. For each of these definitions various characteristics are determined. These include: time invariance of the operator, operator initialization, physical realization, linearity, operational transforms. and memory characteristics of the defining kernels. A measure (m2) for memory retentiveness of the order history is introduced. A generalized linear argument for the order q allows the concept of "tailored" variable order fractional operators whose a, memory may be chosen for a particular application. Memory retentiveness (m2) and order dynamic behavior are investigated and applications are shown. The concept of distributed order operators where the order of the time based operator depends on an additional independent (spatial) variable is also forwarded. Several definitions and their Laplace transforms are developed, analysis methods with these operators are demonstrated, and examples shown. Finally operators of multivariable and distributed order are defined in their various applications are outlined.

Variations in thematic mapper spectra of soil related to tillage and crop residue management - Initial evaluation

NASA Technical Reports Server (NTRS)

Seeley, M. W.; Ruschy, D. L.; Linden, D. R.

1983-01-01

A cooperative research project was initiated in 1982 to study differences in thematic mapper spectral characteristics caused by variable tillage and crop residue practices. Initial evaluations of radiometric data suggest that spectral separability of variably tilled soils can be confounded by moisture and weathering effects. Separability of bare tilled soils from those with significant amounts of corn residue is enhanced by wet conditions, but still possible under dry conditions when recent tillage operations have occurred. In addition, thematic mapper data may provide an alternative method to study the radiant energy balance at the soil surface in conjunction with variable tillage systems.

Multivariate analysis of gamma spectra to characterize used nuclear fuel

DOE PAGES

Coble, Jamie; Orton, Christopher; Schwantes, Jon

2017-01-17

The Multi-Isotope Process (MIP) Monitor provides an efficient means to monitor the process conditions in used nuclear fuel reprocessing facilities to support process verification and validation. The MIP Monitor applies multivariate analysis to gamma spectroscopy of key stages in the reprocessing stream in order to detect small changes in the gamma spectrum, which may indicate changes in process conditions. This research extends the MIP Monitor by characterizing a used fuel sample after initial dissolution according to the type of reactor of origin (pressurized or boiling water reactor; PWR and BWR, respectively), initial enrichment, burn up, and cooling time. Simulated gammamore » spectra were used in this paper to develop and test three fuel characterization algorithms. The classification and estimation models employed are based on the partial least squares regression (PLS) algorithm. A PLS discriminate analysis model was developed which perfectly classified reactor type for the three PWR and three BWR reactor designs studied. Locally weighted PLS models were fitted on-the-fly to estimate the remaining fuel characteristics. For the simulated gamma spectra considered, burn up was predicted with 0.1% root mean squared percent error (RMSPE) and both cooling time and initial enrichment with approximately 2% RMSPE. Finally, this approach to automated fuel characterization can be used to independently verify operator declarations of used fuel characteristics and to inform the MIP Monitor anomaly detection routines at later stages of the fuel reprocessing stream to improve sensitivity to changes in operational parameters that may indicate issues with operational control or malicious activities.« less

Multivariate analysis of gamma spectra to characterize used nuclear fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coble, Jamie; Orton, Christopher; Schwantes, Jon

The Multi-Isotope Process (MIP) Monitor provides an efficient means to monitor the process conditions in used nuclear fuel reprocessing facilities to support process verification and validation. The MIP Monitor applies multivariate analysis to gamma spectroscopy of key stages in the reprocessing stream in order to detect small changes in the gamma spectrum, which may indicate changes in process conditions. This research extends the MIP Monitor by characterizing a used fuel sample after initial dissolution according to the type of reactor of origin (pressurized or boiling water reactor; PWR and BWR, respectively), initial enrichment, burn up, and cooling time. Simulated gammamore » spectra were used in this paper to develop and test three fuel characterization algorithms. The classification and estimation models employed are based on the partial least squares regression (PLS) algorithm. A PLS discriminate analysis model was developed which perfectly classified reactor type for the three PWR and three BWR reactor designs studied. Locally weighted PLS models were fitted on-the-fly to estimate the remaining fuel characteristics. For the simulated gamma spectra considered, burn up was predicted with 0.1% root mean squared percent error (RMSPE) and both cooling time and initial enrichment with approximately 2% RMSPE. Finally, this approach to automated fuel characterization can be used to independently verify operator declarations of used fuel characteristics and to inform the MIP Monitor anomaly detection routines at later stages of the fuel reprocessing stream to improve sensitivity to changes in operational parameters that may indicate issues with operational control or malicious activities.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

B.R. Westphal; J.C. Price; R.D. Mariani

The pyroprocessing of used nuclear fuel via electrorefining requires the continued addition of uranium trichloride to sustain operations. Uranium trichloride is utilized as an oxidant in the system to allow separation of uranium metal from the minor actinides and fission products. The inventory of uranium trichloride had diminished to a point that production was necessary to continue electrorefiner operations. Following initial experimentation, cupric chloride was chosen as a reactant with uranium metal to synthesize uranium trichloride. Despite the variability in equipment and charge characteristics, uranium trichloride was produced in sufficient quantities to maintain operations in the electrorefiner. The results andmore » conclusions from several experiments are presented along with a set of optimized operating conditions for the synthesis of uranium trichloride.« less

Faster quantum searching with almost any diffusion operator

NASA Astrophysics Data System (ADS)

Tulsi, Avatar

2015-05-01

Grover's search algorithm drives a quantum system from an initial state |s > to a desired final state |t > by using selective phase inversions of these two states. Earlier, we studied a generalization of Grover's algorithm that relaxes the assumption of the efficient implementation of Is, the selective phase inversion of the initial state, also known as a diffusion operator. This assumption is known to become a serious handicap in cases of physical interest. Our general search algorithm works with almost any diffusion operator Ds with the only restriction of having |s > as one of its eigenstates. The price that we pay for using any operator is an increase in the number of oracle queries by a factor of O (B ) , where B is a characteristic of the eigenspectrum of Ds and can be large in some situations. Here we show that by using a quantum Fourier transform, we can regain the optimal query complexity of Grover's algorithm without losing the freedom of using any diffusion operator for quantum searching. However, the total number of operators required by the algorithm is still O (B ) times more than that of Grover's algorithm. So our algorithm offers an advantage only if the oracle operator is computationally more expensive than the diffusion operator, which is true in most search problems.

Operations Research techniques in the management of large-scale reforestation programs

Treesearch

Joseph Buongiorno; D.E. Teeguarden

1978-01-01

A reforestation planning system for the Douglas-fir region of the Western United States is described. Part of the system is a simulation model to predict plantation growth and to determine economic thinning regimes and rotation ages as a function of site characteristics, initial density, reforestation costs, and management constraints. A second model estimates the...

A National Evaluation of Safe Schools/Healthy Students: Outcomes and Influences

ERIC Educational Resources Information Center

Derzon, James H.; Yu, Ping; Ellis, Bruce; Xiong, Sharon; Arroyo, Carmen; Mannix, Danyelle; Wells, Michael E.; Hill, Gary; Rollison, Julia

2012-01-01

The Safe Schools/Healthy Students (SS/HS) Initiative has awarded over $2 billion in grants to more than 350 school districts in partnership with local mental health, law enforcement, and juvenile justice agencies. To estimate the impact of grantee characteristics, grant operations, and near-term outcomes in reducing violence and substance use,…

Description of texts of auxiliary programs for processing video information. Part 2: SUODH program of automated separation of quasihomogeneous formations

NASA Technical Reports Server (NTRS)

Borisenko, V. I.; Chesalin, L. S.

1980-01-01

The algorithm, block diagram, complete text, and instructions are given for the use of a computer program to separate formations whose spectral characteristics are constant on the average. The initial material for operating the computer program presented is video information in a standard color-superposition format.

Experimental investigation of inlet-combustor isolators for a dual-mode scramjet at a Mach number of 4

NASA Technical Reports Server (NTRS)

Emami, Saied; Trexler, Carl A.; Auslender, Aaron H.; Weidner, John P.

1995-01-01

This report details experimentally derived operational characteristics of numerous two-dimensional planar inlet-combustor isolator configurations at a Mach number of 4. Variations in geometry included (1) inlet cowl length; (2) inlet cowl rotation angle; (3) isolator length; and (4) utilization of a rearward-facing isolator step. To obtain inlet-isolator maximum pressure-rise data relevant to ramjet-engine combustion operation, configurations were mechanically back pressured. Results demonstrated that the combined inlet-isolator maximum back-pressure capability increases as a function of isolator length and contraction ratio, and that the initiation of unstart is nearly independent of inlet cowl length, inlet cowl contraction ratio, and mass capture. Additionally, data are presented quantifying the initiation of inlet unstarts and the corresponding unstart pressure levels.

DSN human factors project

NASA Technical Reports Server (NTRS)

Chafin, R. L.; Martin, T. H.

1980-01-01

The project plan was to hold focus groups to identify the factors influencing the ease of use characteristics of software and to bond the problem. A questionnaire survey was conducted to evaluate those factors which were more appropriately measured with that method. The performance oriented factors were analyzed and relationships hypothesized. The hypotheses were put to test in the experimental phase of the project. In summary, the initial analysis indicates that there is an initial performance effect favoring computer controlled dialogue but the advantage fades fast as operators become experienced. The user documentation style is seen to have a significant effect on performance. The menu and prompt command formats are preferred by inexperienced operators. The short form mnemonic is least favored. There is no clear best command format but the short form mnemonic is clearly the worst.

Pilot In Command: A Feasibility Assessment of Autonomous Flight Management Operations

NASA Technical Reports Server (NTRS)

Wing, David J.; Ballin, Mark G.; Krishnamurthy, Karthik

2004-01-01

Several years of NASA research have produced the air traffic management operational concept of Autonomous Flight Management with high potential for operational feasibility, significant system and user benefits, and safety. Among the chief potential benefits are demand-adaptive or scalable capacity, user flexibility and autonomy that may finally enable truly successful business strategies, and compatibility with current-day operations such that the implementation rate can be driven from within the user community. A concept summary of Autonomous Flight Management is provided, including a description of how these operations would integrate in shared airspace with existing ground-controlled flight operations. The mechanisms enabling the primary benefits are discussed, and key findings of a feasibility assessment of airborne autonomous operations are summarized. Concept characteristics that impact safety are presented, and the potential for initially implementing Autonomous Flight Management is discussed.

A parametric analysis of visual approaches for helicopters

NASA Technical Reports Server (NTRS)

Moen, G. C.; Dicarlo, D. J.; Yenni, K. R.

1976-01-01

A flight investigation was conducted to determine the characteristic shapes of the altitude, ground speed, and deceleration profiles of visual approaches for helicopters. Two hundred thirty-six visual approaches were flown from nine sets of initial conditions with four types of helicopters. Mathematical relationships were developed that describe the characteristic visual deceleration profiles. These mathematical relationships were expanded to develop equations which define the corresponding nominal ground speed, pitch attitude, pitch rate, and pitch acceleration profiles. Results are applicable to improved helicopter handling qualities in terminal area operations.

Evaluating the HATCH score for predicting progression to sustained atrial fibrillation in ED patients with new atrial fibrillation.

PubMed

Barrett, Tyler W; Self, Wesley H; Wasserman, Brian S; McNaughton, Candace D; Darbar, Dawood

2013-05-01

Atrial fibrillation (AF) is often first detected in the emergency department (ED). Not all AF patients progress to sustained AF (ie, episodes lasting >7 days), which is associated with increased morbidity. The HATCH score stratifies patients with paroxysmal AF according to their risk for progression to sustained AF within 1 year. The HATCH score has previously never been tested in ED patients. We evaluated the accuracy of the HATCH score to predict progression to sustained AF within 1 year of initial AF diagnosis in the ED. We conducted a retrospective cohort study of 253 ED patients with new onset AF and known rhythm status for 1 year following the initial AF detection. The exposure variable was the HATCH score at initial ED evaluation. The primary outcome was rhythm status at 1 year following initial AF diagnosis. We constructed a receiver operating characteristic curve and calculated the area under the curve to estimate the HATCH score's accuracy of predicting progression to sustained AF. Overall, 61 (24%) of 253 of patients progressed to sustained AF within 1 year of initial detection, and the HATCH score receiver operating characteristic area under the curve was 0.62 (95% confidence interval, 0.54-0.70). Among ED patients with new onset AF, the HATCH score was a modest predictor of progression to sustained AF. Because only 2 patients had a HATCH greater than 5, this previously recommended cut-point was not useful in identifying high-risk patients in this cohort. Refinement of this decision aid is needed to improve its prognostic accuracy in the ED population. Copyright © 2013 Elsevier Inc. All rights reserved.

Investigation on quench initiation and propagation characteristics of GdBCO coil co-wound with a stainless steel tape as turn-to-turn metallic insulation.

PubMed

Kim, Y G; Song, J B; Choi, Y H; Yang, D G; Kim, S G; Lee, H G

2016-11-01

This paper investigates the quench initiation and propagation characteristics of a metallic insulation (MI) coil by conducting thermal quench tests for a GdBCO single-pancake coil co-wound with a stainless steel tape as the turn-to-turn MI. The test results confirmed that the MI coil exhibited superior thermal and electrical stabilities compared to the conventional coils co-wound with organic insulation material because the operating current could flow along the radial direction due to the existence of a turn-to-turn contact when a local hot spot was generated. The results of the quench test at a heater current (I h ) of 12, 13, and 14 A indicate that the MI coil possesses a self-protecting characteristic resulting from the "current bypass" through the turn-to-turn contact. However, the test coil was not self-protecting at I h = 15 A because the Joule heat energy generated by the radial current flow was not completely dissipated due to the characteristic resistance of the metallic insulation tape and the non-superconducting materials, including the substrate, stabilizer, and buffer layers within the high-temperature superconductor (HTS) tape. Even though the MI coil possesses superior thermal and electrical stability relative to those of conventional HTS coils co-wound with an organic material as turn-to-turn insulation, it is essential to consider the critical role of the Joule heat energy resulting from the operating current and stored magnetic energy as well as the characteristic resistances in order to further develop self-protective 2G HTS magnets.

The characteristics of railway service disruption: implications for disruption management.

PubMed

Golightly, D; Dadashi, N

2017-03-01

Rail disruption management is central to operational continuity and customer satisfaction. Disruption is not a unitary phenomenon - it varies by time, cause, location and complexity of coordination. Effective, user-centred technology for rail disruption must reflect this variety. A repertory grid study was conducted to elicit disruption characteristics. Construct elicitation with a group of experts (n = 7) captured 26 characteristics relevant to rail disruption. A larger group of operational staff (n = 28) rated 10 types of rail incident against the 26 characteristics. The results revealed distinctions such as business impact and public perception, and the importance of management of the disruption over initial detection. There were clear differences between those events that stop the traffic, as opposed to those that only slow the traffic. The results also demonstrate the utility of repertory grid for capturing the characteristics of complex work domains. Practitioner Summary: The aim of the paper is to understand how variety in rail disruption influences socio-technical design. It uses repertory grid to identify and prioritise 26 constructs, and group 10 disruption types, identifying critical factors such as whether an incident stops or merely slows the service, and business reputation.

Initial Study of an Effective Fast-Time Simulation Platform for Unmanned Aircraft System Traffic Management

NASA Technical Reports Server (NTRS)

Xue, Min; Rios, Joseph

2017-01-01

Small Unmanned Aerial Vehicles (sUAVs), typically 55 lbs and below, are envisioned to play a major role in surveilling critical assets, collecting important information, and delivering goods. Large scale small UAV operations are expected to happen in low altitude airspace in the near future. Many static and dynamic constraints exist in low altitude airspace because of manned aircraft or helicopter activities, various wind conditions, restricted airspace, terrain and man-made buildings, and conflict-avoidance among sUAVs. High sensitivity and high maneuverability are unique characteristics of sUAVs that bring challenges to effective system evaluations and mandate such a simulation platform different from existing simulations that were built for manned air traffic system and large unmanned fixed aircraft. NASA's Unmanned aircraft system Traffic Management (UTM) research initiative focuses on enabling safe and efficient sUAV operations in the future. In order to help define requirements and policies for a safe and efficient UTM system to accommodate a large amount of sUAV operations, it is necessary to develop a fast-time simulation platform that can effectively evaluate requirements, policies, and concepts in a close-to-reality environment. This work analyzed the impacts of some key factors including aforementioned sUAV's characteristics and demonstrated the importance of these factors in a successful UTM fast-time simulation platform.

Initial Study of An Effective Fast-Time Simulation Platform for Unmanned Aircraft System Traffic Management

NASA Technical Reports Server (NTRS)

Xue, Min; Rios, Joseph

2017-01-01

Small Unmanned Aerial Vehicles (sUAVs), typically 55 lbs and below, are envisioned to play a major role in surveilling critical assets, collecting important information, and delivering goods. Large scale small UAV operations are expected to happen in low altitude airspace in the near future. Many static and dynamic constraints exist in low altitude airspace because of manned aircraft or helicopter activities, various wind conditions, restricted airspace, terrain and man-made buildings, and conflict-avoidance among sUAVs. High sensitivity and high maneuverability are unique characteristics of sUAVs that bring challenges to effective system evaluations and mandate such a simulation platform different from existing simulations that were built for manned air traffic system and large unmanned fixed aircraft. NASA's Unmanned aircraft system Traffic Management (UTM) research initiative focuses on enabling safe and efficient sUAV operations in the future. In order to help define requirements and policies for a safe and efficient UTM system to accommodate a large amount of sUAV operations, it is necessary to develop a fast-time simulation platform that can effectively evaluate requirements, policies, and concepts in a close-to-reality environment. This work analyzed the impacts of some key factors including aforementioned sUAV's characteristics and demonstrated the importance of these factors in a successful UTM fast-time simulation platform.

Open and endovascular aneurysm repair in the Society for Vascular Surgery Vascular Quality Initiative.

PubMed

Spangler, Emily L; Beck, Adam W

2017-12-01

The Society for Vascular Surgery Vascular Quality Initiative is a patient safety organization and a collection of procedure-based registries that can be utilized for quality improvement initiatives and clinical outcomes research. The Vascular Quality Initiative consists of voluntary participation by centers to collect data prospectively on all consecutive cases within specific registries which physicians and centers elect to participate. The data capture extends from preoperative demographics and risk factors (including indications for operation), through the perioperative period, to outcomes data at up to 1-year of follow-up. Additionally, longer-term follow-up can be achieved by matching with Medicare claims data, providing long-term longitudinal follow-up for a majority of patients within the Vascular Quality Initiative registries. We present the unique characteristics of the Vascular Quality Initiative registries and highlight important insights gained specific to open and endovascular abdominal aortic aneurysm repair. Copyright © 2017 Elsevier Inc. All rights reserved.

A Quality Assurance Initiative for Commercial-Scale Production in High-Throughput Cryopreservation of Blue Catfish Sperm

PubMed Central

Hu, E; Liao, T. W.; Tiersch, T. R.

2013-01-01

Cryopreservation of fish sperm has been studied for decades at a laboratory (research) scale. However, high-throughput cryopreservation of fish sperm has recently been developed to enable industrial-scale production. This study treated blue catfish (Ictalurus furcatus) sperm high-throughput cryopreservation as a manufacturing production line and initiated quality assurance plan development. The main objectives were to identify: 1) the main production quality characteristics; 2) the process features for quality assurance; 3) the internal quality characteristics and their specification designs; 4) the quality control and process capability evaluation methods, and 5) the directions for further improvements and applications. The essential product quality characteristics were identified as fertility-related characteristics. Specification design which established the tolerance levels according to demand and process constraints was performed based on these quality characteristics. Meanwhile, to ensure integrity throughout the process, internal quality characteristics (characteristics at each quality control point within process) that could affect fertility-related quality characteristics were defined with specifications. Due to the process feature of 100% inspection (quality inspection of every fish), a specific calculation method, use of cumulative sum (CUSUM) control charts, was applied to monitor each quality characteristic. An index of overall process evaluation, process capacity, was analyzed based on in-control process and the designed specifications, which further integrates the quality assurance plan. With the established quality assurance plan, the process could operate stably and quality of products would be reliable. PMID:23872356

Estimation of the Arrival Time and Duration of a Radio Signal with Unknown Amplitude and Initial Phase

NASA Astrophysics Data System (ADS)

Trifonov, A. P.; Korchagin, Yu. E.; Korol'kov, S. V.

2018-05-01

We synthesize the quasi-likelihood, maximum-likelihood, and quasioptimal algorithms for estimating the arrival time and duration of a radio signal with unknown amplitude and initial phase. The discrepancies between the hardware and software realizations of the estimation algorithm are shown. The characteristics of the synthesized-algorithm operation efficiency are obtained. Asymptotic expressions for the biases, variances, and the correlation coefficient of the arrival-time and duration estimates, which hold true for large signal-to-noise ratios, are derived. The accuracy losses of the estimates of the radio-signal arrival time and duration because of the a priori ignorance of the amplitude and initial phase are determined.

Hardware test program for evaluation of baseline range/range rate sensor concept

NASA Technical Reports Server (NTRS)

1985-01-01

The Hardware Test Program for evaluation of the baseline range/range rate sensor concept was initiated 11 September 1984. This ninth report covers the period 12 May through 11 June 1885. A contract amendment adding a second phase has extended the Hardware Test Program through 10 December 1985. The objective of the added program phase is to establish range and range measurement accuracy and radar signature characteristics for a typical spacecraft target. Phase I of the Hardware Test Program was designed to reduce the risks associated with the Range/Range Rate (R/R) Sensor baseline design approach. These risks are associated with achieving the sensor performance required for the two modes of operation, the Interrupted CW (ICW) mode for initial acquisition and tracking to close-in ranges, and the CW mode, providing coverage during the final docking maneuver. The risks associated with these modes of operation have to do with the realization of adequate sensitivity to operate to their individual maximum ranges.

Operational Characteristics of a Rotating Detonation Engine Using Hydrogen and Air

DTIC Science & Technology

2011-06-01

Naval Research Laboratory PDE Pulsed detonation engine RDE Rotating detonation engine TDW Transverse detonation wave Symbols [SI units...primarily been on pulsed detonation engines ( PDEs ). Recently, however, detonation research has begun to also focus on rotating , or continuous... rotating detonation engines have been studied, however, more progress was initially made regarding PDEs . Recently, though, there has been a renewed

Improved gas thrust bearings

NASA Technical Reports Server (NTRS)

Anderson, W. J.; Etsion, I.

1979-01-01

Two variations of gas-lubricated thrust bearings extend substantially load-carrying range over existing gas bearings. Dual-Action Gas Thrust Bearing's load-carrying capacity is more than ninety percent greater than that of single-action bearing over range of compressibility numbers. Advantages of Cantilever-mounted Thrust Bearing are greater tolerance to dirt ingestion, good initial lift-off characteristics, and operational capability over wide temperature range.

The use of high altitude aerial photography to inventory wildlife habitat in Kansas: An initial evaluation

NASA Technical Reports Server (NTRS)

Merchant, J. W.; Waddell, B. H.

1974-01-01

The use of aerial photography as a method for determining the wildlife conditions of an area is discussed. Color infrared photography is investigated as the most effective type of remote sensor. The characteristics of the remote sensing systems are described. Examples of the remote sensing operation and the method for reducing the data are presented.

Thick tumor capsule is a valuable risk factor for distant metastasis in follicular thyroid carcinoma.

PubMed

Shimbashi, Wataru; Sugitani, Iwao; Kawabata, Kazuyoshi; Mitani, Hiroki; Toda, Kazuhisa; Yamada, Keiko; Sato, Yukiko

2018-02-01

While the biological behavior of follicular thyroid carcinoma (FTC) has been studied in great detail using clinical experience, few studies have investigated pre- or intraoperative factors related to the risk of distant metastasis (DM) among patients with FTC. The aim of this study was to analyze the characteristics of FTC with DM. This study retrospectively investigated 102 patients with FTC who underwent surgery between 1988 and 2013. We compared clinicopathological characteristics between FTC with and without DM. Univariate analysis revealed nodal metastasis (p=0.045), serum thyroglobulin (Tg) at initial operation (≥1000ng/ml; p<0.0001), widely invasive appearance according to macroscopic findings (p<0.0001), thick tumor capsule (≥1mm; p<0.0001), vascular invasion (p=0.0003), extrathyroidal invasion (p=0.047), and venous tumor embolism (p=0.045) as significant risk factors for DM. Multivariate analysis conducted using pre- and intraoperative factors identified thick tumor capsule (≥1mm), serum Tg at initial operation (≥1000ng/ml), and macroscopically widely invasive appearance as risk factors independently associated with development of DM. Patients with these risk factors should undergo total thyroidectomy and radioactive iodine ablation. Copyright © 2017 Elsevier B.V. All rights reserved.

Fixed-bed adsorption study of methylene blue onto pyrolytic tire char

NASA Astrophysics Data System (ADS)

Makrigianni, Vassiliki; Giannakas, Aris; Papadaki, Maria; Albanis, Triantafyllos; Konstantinou, Ioannis

2016-04-01

In this work, the adsorption efficiency of acid treated pyrolytic tire char to cationic methylene blue (MB) dye adsorption from aqueous solutions was investigated by fixed-bed adsorption column experiments. The effects of the initial dye concentration (10 - 40 mg L-1) and feed flow rate (50 - 150 mL min -1) with a fixed bed height (15 cm) were studied in order to determine the breakthrough characteristics of the adsorption system. The Adams-Bohart, Yoon-Nelson and Thomas model were applied to the adsorption of MB onto char at different operational conditions to predict the breakthrough curves and to determine the characteristic parameters of the column. The results showed that the maximum adsorbed quantities decreased with increasing flow rate and increased with increasing initial MB concentration. Breakthrough time and exhaustion time increased with decreasing inlet dye concentration and flow rate. In contrast with Adams-Bohart model, Yoon-Nelson model followed by Thomas model were found more suitable to describe the fixed-bed adsorption of methylene blue by char. The correlation coefficient values R2 for both models at different operating conditions are higher than 0.9 and the low average relative error values provided very good fittings of experimental data at different operating conditions. Higher adsorption capacity of 3.85 mg g -1 was obtained at 15 cm of adsorbent bed height, flow rate of 100 mL min -1and initial MB concentration of 40 mg L-1. Although that activated carbons exhibited higher adsorption capacities in the literature, acid-treated pyrolytic tire char was found to be considerably efficient adsorbent for the removal of MB dye column taking into account the advantages of the simpler production process compared to activated carbons, as well as, the availability of waste tire feedstock and concurrent waste tire management.

Evaluation of isotopic composition of fast reactor core in closed nuclear fuel cycle

NASA Astrophysics Data System (ADS)

Tikhomirov, Georgy; Ternovykh, Mikhail; Saldikov, Ivan; Fomichenko, Peter; Gerasimov, Alexander

2017-09-01

The strategy of the development of nuclear power in Russia provides for use of fast power reactors in closed nuclear fuel cycle. The PRORYV (i.e. «Breakthrough» in Russian) project is currently under development. Within the framework of this project, fast reactors BN-1200 and BREST-OD-300 should be built to, inter alia, demonstrate possibility of the closed nuclear fuel cycle technologies with plutonium as a main source of energy. Russia has a large inventory of plutonium which was accumulated in the result of reprocessing of spent fuel of thermal power reactors and conversion of nuclear weapons. This kind of plutonium will be used for development of initial fuel assemblies for fast reactors. The closed nuclear fuel cycle concept of the PRORYV assumes self-supplied mode of operation with fuel regeneration by neutron capture reaction in non-enriched uranium, which is used as a raw material. Operating modes of reactors and its characteristics should be chosen so as to provide the self-sufficient mode by using of fissile isotopes while refueling by depleted uranium and to support this state during the entire period of reactor operation. Thus, the actual issue is modeling fuel handling processes. To solve these problems, the code REPRORYV (Recycle for PRORYV) has been developed. It simulates nuclide streams in non-reactor stages of the closed fuel cycle. At the same time various verified codes can be used to evaluate in-core characteristics of a reactor. By using this approach various options for nuclide streams and assess the impact of different plutonium content in the fuel, fuel processing conditions, losses during fuel processing, as well as the impact of initial uncertainties on neutron-physical characteristics of reactor are considered in this study.

[Development characteristics of aquatic plants in a constructed wetland for treating urban drinking water source at its initial operation stage].

PubMed

Zheng, Jun; Ma, Xin-Tang; Zhou, Lan; Zhou, Qing-Yuan; Wang, Zhong-Qiong; Wang, Wei-Dong; Yin, Cheng-Qing

2011-08-01

The development characteristics and improvement measures of aquatic plants were studied in Shijiuyang Constructed Wetland (SCW) at its initial operation stage. SCW was a large-scale wetland aiming to help relieve the source water pollution in Jiaxing City. A checklist of vascular plants in SCW was built, and species composition, life forms, biomass and association distributions were examined. Our objectives were to examine the diversity and community structure of aquatic plants in SCW at its initial operation stage, and to find out the possible hydrophyte improvement measures. The survey results showed that there were 49 vascular plant species belonging to 41 genera, 25 families in SCW, which greatly exceeded the artificially transplanted 13 species. The life forms of present aquatic plants in SCW were dominated by hygrophilous plants (20 species) and emerged plants (17 species), which accounted for 75.5% of the total number of aquatic plants. The aquatic plants transplanted artificially were dominated by emerged plants (accounted for 69.2%), while those naturally developed were predominated by hygrophilous plants (accounted for 47.2%). The horizontal distribution of aquatic plant community in SCW was mixed in the form of mosaics, which made up typical association complex. Except association Aeschynomene indica L., the dominant species of other associations were all those transplanted artificially. The naturally grown species scattered throughout the SCW and only occupied a small percentage. A marked difference was detected on the species and species richness of aquatic plants in different regions of SCW. Biomass of aquatic plant associations in SCW was 167.7 t. SCW has shown a trend of succession heading for quick increase of plant diversity at the primary operation stage. This trend provides a good material base for the future stable community of aquatic plants in SCW. According to the current status of aquatic plants, some suggestions were put forward on the further optimization and utilization of aquatic plant systems in SCW.

Early, de novo atrial fibrillation after coronary artery bypass grafting: Facts and features.

PubMed

Yaksh, Ameeta; Kik, Charles; Knops, Paul; van Ettinger, Maarten J B; Bogers, Ad J J C; de Groot, Natasja M S

2017-02-01

Knowledge of the mechanism underlying post-operative atrial fibrillation (PoAF) is essential for development of preventive measures. The incidence and characteristics of both PoAF and supraventricular premature beats triggering PoAF, their interrelationship and alterations over time have never been examined. The goal of this study is therefore to examine the correlation between the incidence and characteristics of supraventricular premature beats (SVPBs) and PoAF episodes in patients undergoing CABG in the first five post-operative days. PoAF episodes (N=327) and SVPBs (N=141,873) were characterized in 29 patients (63±9 years; 22 (76%) male) undergoing coronary artery bypass grafting and compared with a control group of patients without PoAF by using continuous cardiac rhythm monitoring during the first 5 days after surgery. Most patients (N=18, 62%) had multiple PoAF episodes; the median number of PoAF episodes per patient was 3 and varied between 1 and 139. The majority of PoAF episodes developed on the second and third post-operative day (55%). The averaged median duration of PoAF episodes per patient was 469±1085 min. Patients with PoAF had a higher SVPBs burden compared to subjects without PoAF (0.9% vs 0.2%, P<.001). SVPBs initiating PoAF had shorter coupling intervals than SVPBs which did not initiate PoAF episodes (58% vs 64% (P<.001) and were preceded by heart rate acceleration. PoAF episodes are mainly repetitive though transient in nature. There was a considerable inter-individual variation in both AF and SVPB characteristics, despite a similar underlying clinical profile. The SVPB burden is higher in patients with PoAF and the mode of onset is characterized by short coupled SVPBs. Determination of individual post-operative dysrhythmia profiles enables identification of patients at risk for developing PoAF. Copyright © 2016 Elsevier Inc. All rights reserved.

Increasing time to postoperative stereotactic radiation therapy for patients with resected brain metastases: investigating clinical outcomes and identifying predictors associated with time to initiation.

PubMed

Yusuf, Mehran B; Amsbaugh, Mark J; Burton, Eric; Nelson, Megan; Williams, Brian; Koutourousiou, Maria; Nauta, Haring; Woo, Shiao

2018-02-01

We sought to determine the impact of time to initiation (TTI) of post-operative radiosurgery on clinical outcomes for patients with resected brain metastases and to identify predictors associated with TTI. All patients with resected brain metastases treated with postoperative SRS or fractionated stereotactic radiation therapy (fSRT) from 2012 to 2016 at a single institution were reviewed. TTI was defined as the interval from resection to first day of radiosurgery. Receiver operating characteristic (ROC) curves were used to identify an optimal threshold for TTI with respect to local failure (LF). Survival outcomes were estimated using the Kaplan-Meier method and analyzed using the log-rank test and Cox proportional hazards models. Logistic regression models were used to identify factors associated with ROC-determined TTI covariates. A total of 79 resected lesions from 73 patients were evaluated. An ROC curve of LF and TTI identified an optimal threshold for TTI of 30.5 days, with an area under the curve of 0.637. TTI > 30 days was associated with an increased hazard of LF (HR 4.525, CI 1.239-16.527) but was not significantly associated with survival (HR 1.002, CI 0.547-1.823) or distant brain failure (DBF, HR 1.943, CI 0.989-3.816). Fifteen patients (20.5%) required post-operative inpatient rehabilitation. Post-operative rehabilitation was associated with TTI > 30 days (OR 1.48, CI 1.142-1.922). In our study of resected brain metastases, longer time to initiation of post-operative radiosurgery was associated with increased local failure. Ideally, post-op SRS should be initiated within 30 days of resection if feasible.

The nature and use of prediction skills in a biological computer simulation

NASA Astrophysics Data System (ADS)

Lavoie, Derrick R.; Good, Ron

The primary goal of this study was to examine the science process skill of prediction using qualitative research methodology. The think-aloud interview, modeled after Ericsson and Simon (1984), let to the identification of 63 program exploration and prediction behaviors.The performance of seven formal and seven concrete operational high-school biology students were videotaped during a three-phase learning sequence on water pollution. Subjects explored the effects of five independent variables on two dependent variables over time using a computer-simulation program. Predictions were made concerning the effect of the independent variables upon dependent variables through time. Subjects were identified according to initial knowledge of the subject matter and success at solving three selected prediction problems.Successful predictors generally had high initial knowledge of the subject matter and were formal operational. Unsuccessful predictors generally had low initial knowledge and were concrete operational. High initial knowledge seemed to be more important to predictive success than stage of Piagetian cognitive development.Successful prediction behaviors involved systematic manipulation of the independent variables, note taking, identification and use of appropriate independent-dependent variable relationships, high interest and motivation, and in general, higher-level thinking skills. Behaviors characteristic of unsuccessful predictors were nonsystematic manipulation of independent variables, lack of motivation and persistence, misconceptions, and the identification and use of inappropriate independent-dependent variable relationships.

Design, fabrication and testing of an optical temperature sensor

NASA Technical Reports Server (NTRS)

Morey, W. W.; Glenn, W. H.; Decker, R. O.; Mcclurg, W. C.

1980-01-01

The laboratory breadboard optical temperature sensor based on the temperature dependent absorptive characteristics of a rare earth (europium) doped optical fiber. The principles of operation, materials characterization, fiber and optical component design, design and fabrication of an electrooptic interface unit, signal processing, and initial test results are discussed. Initial tests indicated that, after a brief warmup period, the output of the sensor was stable to approximately 1 C at room temperature or approximately + or - 0.3 percent of point (K). This exceeds the goal of 1 percent of point. Recommendations are presented for further performance improvement.

Photovoltaic Test and Demonstration Project. [for solar cell power systems

NASA Technical Reports Server (NTRS)

Forestieri, A. F.; Brandhorst, H. W., Jr.; Deyo, J. N.

1976-01-01

The Photovoltaic Test and Demonstration Project was initiated by NASA in June, 1975, to develop economically feasible photovoltaic power systems suitable for a variety of terrestrial applications. Objectives include the determination of operating characteristic and lifetimes of a variety of solar cell systems and components and development of methodology and techniques for accurate measurements of solar cell and array performance and diagnostic measurements for solar power systems. Initial work will be concerned with residential applications, with testing of the first prototype system scheduled for June, 1976. An outdoor 10 kW array for testing solar power systems is under construction.

Analysis of the performance of the drive system and diffuser of the Langley unitary plan wind tunnel

NASA Technical Reports Server (NTRS)

Hasel, L. E.; Stallings, R. L.

1981-01-01

A broad program was initiated at the Langley Research Center in 1973 to reduce the energy consumption of the laboratory. As a part of this program, the performance characteristics of the Unitary Plan Wind Tunnel were reexamined to determine if potential methods for incresing the operating efficiencies of the tunnel could be formulated. The results of that study are summarized. The performance characteristics of the drive system components and the variable-geometry diffuser system of the tunnel are documented and analyzed. Several potential methods for reducing the energy requirements of the facility are discussed.

Improving Reliability of Service Operation Using FMEA Review and New Opportunity for Investigations

NASA Astrophysics Data System (ADS)

Sutrisno, Agung; Gunawan, Indra

2016-01-01

Despite its growing contribution to the global economy, investigation on the application status of service FMEA study to support realization of reliable service operation is very limited in literature. Motivated by such situation, the paper presented an initial survey on the status and research gaps in developing and applying FMEA in service sectors. Systematic preliminary survey using specific criteria are undertaken. Our study indicated that development and application of service FMEA are partially addressing the characteristics of service operations and it is still applied into the good deed and profit oriented operations. Opportunities for further investigation pertaining to advancement of its decision supporting tool for service risk appraisal, its modification to cope with sustainability related requirements and application of service FMEA in not for profit oriented operations are presented as new avenues for further investigation

Time to first take-back operation predicts successful primary fascial closure in patients undergoing damage control laparotomy.

PubMed

Pommerening, Matthew J; DuBose, Joseph J; Zielinski, Martin D; Phelan, Herb A; Scalea, Thomas M; Inaba, Kenji; Velmahos, George C; Whelan, James F; Wade, Charles E; Holcomb, John B; Cotton, Bryan A

2014-08-01

Failure to achieve primary fascial closure (PFC) after damage control laparotomy is costly and carries great morbidity. We hypothesized that time from the initial laparotomy to the first take-back operation would be predictive of successful PFC. Trauma patients managed with open abdominal techniques after damage control laparotomy were prospectively followed at 14 Level 1 trauma centers during a 2-year period. Time to the first take-back was evaluated as a predictor of PFC using hierarchical multivariate logistic regression analysis. A total of 499 patients underwent damage control laparotomy and were included in this analysis. PFC was achieved in 327 (65.5%) patients. Median time to the first take-back operation was 36 hours (interquartile range 24-48). After we adjusted for patient demographics, resuscitation volumes, and operative characteristics, increasing time to the first take-back was associated with a decreased likelihood of PFC. Specifically, each hour delay in return to the operating room (24 hours after initial laparotomy) was associated with a 1.1% decrease in the odds of PFC (odds ratio 0.989; 95% confidence interval 0.978-0.999; P = .045). In addition, there was a trend towards increased intra-abdominal complications in patients returning after 48 hours (odds ratio 1.80; 95% confidence interval 1.00-3.25; P = .05). Data from this prospective, multicenter study demonstrate that delays in returning to the operating room after damage control laparotomy are associated with reductions in PFC. These findings suggest that emphasis should be placed on returning to the operating room within 24 hours after the initial laparotomy if possible (and no later than 48 hours). Copyright © 2014 Mosby, Inc. All rights reserved.

Radar-based alert system to operate a sewerage network: relevance and operational effectiveness after several years of use.

PubMed

Faure, D; Payrastre, O; Auchet, P

2005-01-01

Since January 2000, the sewerage network of a very urbanised catchment area in the Greater Nancy Urban Community has been operated according to the alarms generated in real time by a storm alert system using weather radar data. This alert system is based on an automatic identification of intense rain cells in the radar images. This paper presents the characteristics of this alert system and synthesises the main results of two complementary studies realised in 2002 in order to estimate the relevance and the operational effectiveness of the alert system. The first study consisted in an off-line analysis of almost 50,000 intense rain cells detected in four years of historical radar data. The second study was an analysis of the experience feedback after two years of operational use of this alert system. The results of these studies are discussed in function of the initial operational objectives.

Resident training in a new robotic thoracic surgery program.

PubMed

White, Yasmine N; Dedhia, Priya; Bergeron, Edward J; Lin, Jules; Chang, Andrew A; Reddy, Rishindra M

2016-03-01

The volume of robot-assisted operations has drastically increased over the past decade. New programs have focused on training surgeons, whereas resident training has lagged behind. The objective of this study was to evaluate our institutional experience with resident participation in thoracic robotic surgery cases since the initiation of our program. The first 100 robotic thoracic surgery cases at our institution were retrospectively reviewed and categorized into three sequential cohorts. Procedure type, patient and operative characteristics, level of resident participation (primary surgeon [PS] or assistant), and postoperative variables were evaluated. Of the first 100 cases, 38% were lung resections, 23% were esophageal operations, and 20% were sympathectomies. The distribution of cases changed over time with the proportion of pulmonary resections significantly increasing. Patient age (P < 0.05), body mass index (P = not significant [NS]), and comorbidities (P = NS) increased over time. Resident participation as PS increased from 33%-59% between the early and late cohorts (P < 0.05). A subset analysis of the 20 lobectomies (7 attending PS, 13 residents) showed similar patient characteristics (P = NS): age (67 versus 69), body mass index (29.5 versus 26.1), and American Society of Anesthesiologists category (2.8 versus 2.8). Operative and postoperative characteristics were also similar (P = NS) regardless of PS: operative time (260 versus 249 min), estimated blood loss (187 versus 203 mL), and length of stay (4.8 versus 4.7 d). Residents can participate as the PS in a variety of thoracic operations during the implementation of a robotics program. Operative time, estimated blood loss, and length of stay were similar regardless of level of resident participation. Copyright © 2016 Elsevier Inc. All rights reserved.

Hollow-Cathode Source Generates Plasma

NASA Technical Reports Server (NTRS)

Deininger, W. D.; Aston, G.; Pless, L. C.

1989-01-01

Device generates argon, krypton, or xenon plasma via thermionic emission and electrical discharge within hollow cathode and ejects plasma into surrounding vacuum. Goes from cold start up to full operation in less than 5 s after initial application of power. Exposed to moist air between operations without significant degradation of starting and running characteristics. Plasma generated by electrical discharge in cathode barrel sustained and aided by thermionic emission from emitter tube. Emitter tube does not depend on rare-earth oxides, making it vulnerable to contamination by exposure to atmosphere. Device modified for use as source of plasma in laboratory experiments or industrial processes.

High-power operation of highly reliable narrow stripe pseudomorphic single quantum well lasers emitting at 980 nm

NASA Technical Reports Server (NTRS)

Larsson, A.; Forouhar, S.; Cody, J.; Lang, R. J.

1990-01-01

Ridge waveguide pseudomorphic InGaAs/GaAs/AlGaAs single-quantum-well lasers exhibiting record high quantum efficiencies and high output power densities (105 mW per facet from a 6 micron wide stripe) at a lasing wavelength of 980 nm are discussed that were fabricated from a graded index separate confinement heterostructure grown by molecular beam epitaxy. Life testing at an output power of 30 mW per uncoated facet reveals a slow gradual degradation during the initial 500 h of operation after which the operating characteristics of the lasers become stable. The emission wavelength, the high output power, and the fundamental lateral mode operation render these lasers suitable for pumping Er3+-doped fiber amplifiers.

Heat transfer characteristics of a surface type direct contact boiler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deeds, R.S.; Jacobs, H.R.; Boehm, R.F.

1976-03-01

Two direct contact heat exchangers were constructed and test results were obtained using water and refrigerant 113 as the working fluids. The heat exchangers were operated in a three-phase mode; the water remained liquid throughout the vessel and the liquid refrigerant 113 underwent vaporization following direct injection into the water. The effect of important operational parameters--operating heights, refrigerant 113 injection techniques, mass flow ratios, and temperatures--was studied to determine generalized trends important in the design and operation of a prototype three-phase direct contact heat exchanger. The primary system used in this study performed well overall. The initial favorable results ofmore » this study warrant further investigation of direct contact heat exchange as a means of utilizing geothermal energy.« less

Space Station life sciences guidelines for nonhuman experiment accommodation

NASA Technical Reports Server (NTRS)

Arno, R.; Hilchey, J.

1985-01-01

Life scientists will utilize one of four habitable modules which constitute the initial Space Station configuration. This module will be initially employed for studies related to nonhuman and human life sciences. At a later date, a new module, devoted entirely to nonhuman life sciences will be launched. This report presents a description of the characteristics of a Space Station laboratory facility from the standpoint of nonhuman research requirements. Attention is given to the science rationale for experiments which support applied medical research and basic gravitational biology, mission profiles and typical equipment and subsystem descriptions, issues associated with the accommodation of nonhuman life sciences on the Space Station, and conceptual designs for the initial operational capability configuration and later Space Station life-sciences research facilities.

Ground and Flight Evaluation of a Small-Scale Inflatable-Winged Aircraft

NASA Technical Reports Server (NTRS)

Murray, James E.; Pahle, Joseph W.; Thornton, Stephen V.; Vogus, Shannon; Frackowiak, Tony; Mello, Joe; Norton, Brook; Bauer, Jeff (Technical Monitor)

2002-01-01

A small-scale, instrumented research aircraft was flown to investigate the night characteristics of innersole wings. Ground tests measured the static structural characteristics of the wing at different inflation pressures, and these results compared favorably with analytical predictions. A research-quality instrumentation system was assembled, largely from commercial off-the-shelf components, and installed in the aircraft. Initial flight operations were conducted with a conventional rigid wing having the same dimensions as the inflatable wing. Subsequent flights were conducted with the inflatable wing. Research maneuvers were executed to identify the trim, aerodynamic performance, and longitudinal stability and control characteristics of the vehicle in its different wing configurations. For the angle-of-attack range spanned in this flight program, measured flight data demonstrated that the rigid wing was an effective simulator of the lift-generating capability of the inflatable wing. In-flight inflation of the wing was demonstrated in three flight operations, and measured flight data illustrated the dynamic characteristics during wing inflation and transition to controlled lifting flight. Wing inflation was rapid and the vehicle dynamics during inflation and transition were benign. The resulting angles of attack and of sideslip ere small, and the dynamic response was limited to roll and heave motions.

A Spherical Torus Nuclear Fusion Reactor Space Propulsion Vehicle Concept for Fast Interplanetary Travel

NASA Technical Reports Server (NTRS)

Williams, Craig H.; Borowski, Stanley K.; Dudzinski, Leonard A.; Juhasz, Albert J.

1998-01-01

A conceptual vehicle design enabling fast outer solar system travel was produced predicated on a small aspect ratio spherical torus nuclear fusion reactor. Initial requirements were for a human mission to Saturn with a greater than 5% payload mass fraction and a one way trip time of less than one year. Analysis revealed that the vehicle could deliver a 108 mt crew habitat payload to Saturn rendezvous in 235 days, with an initial mass in low Earth orbit of 2,941 mt. Engineering conceptual design, analysis, and assessment was performed on all ma or systems including payload, central truss, nuclear reactor (including divertor and fuel injector), power conversion (including turbine, compressor, alternator, radiator, recuperator, and conditioning), magnetic nozzle, neutral beam injector, tankage, start/re-start reactor and battery, refrigeration, communications, reaction control, and in-space operations. Detailed assessment was done on reactor operations, including plasma characteristics, power balance, power utilization, and component design.

Gravity Effect on Capillary Limit in a Miniature Loop Heat Pipe with Multiple Evaporators and Multiple Condensers

NASA Technical Reports Server (NTRS)

Nagano, Hosei; Ku, Jentung

2007-01-01

This paper describes the gravity effect on heat transport characteristics in a minia6re loop heat pipe with multiple evaporators and multiple condensers. Tests were conducted in three different orientations: horizontal, 45deg tilt, and vertical. The gravity affected the loop's natural operating temperature, the maximum heat transport capability, and the thermal conductance. In the case that temperatures of compensation chambers were actively controlled, the required control heater power was also dependent on the test configuration. In the vertical configuration, the secondary wick was not able to pump the liquid from the CC to the evaporator against the gravity. Thus the loop could operate stably or display some peculiar behaviors depending on the initial liquid distribution between the evaporator and the CC. Because such an initial condition was not known prior to the test, the subsequent loop performance was unpredictable.

Demand for large freighter aircraft as projected by the NASA cargo/logistics airlift systems studies

NASA Technical Reports Server (NTRS)

Whitehead, A. H., Jr.; Kuhlman, W. H.

1979-01-01

This paper examines the market conditions up through the year 2008 to provide a preliminary assessment of the potential for and the characteristics of an advanced, all-cargo transport aircraft. Any new freighter must compete with current wide-body aircraft and their derivatives. Aircraft larger than the wide-bodies may incur economic penalties and operational problems. A lower direct operating cost is not a sufficient criterion to base a decision for the initiation of a new aircraft development or to select aircraft characteristics. Other factors of equal importance that are reviewed in this paper include considerations of the system infrastructure, the economics of the airlines, and the aircraft manufacturer return on investment. The results of the market forecast and a computer simulation show that an advanced long range aircraft with a payload between 68 to 181 tonnes (75 to 200 tons) could generate a solid foothold beginning around 1994.

Parametric analyses of planned flowing uranium hexafluoride critical experiments

NASA Technical Reports Server (NTRS)

Rodgers, R. J.; Latham, T. S.

1976-01-01

Analytical investigations were conducted to determine preliminary design and operating characteristics of flowing uranium hexafluoride (UF6) gaseous nuclear reactor experiments in which a hybrid core configuration comprised of UF6 gas and a region of solid fuel will be employed. The investigations are part of a planned program to perform a series of experiments of increasing performance, culminating in an approximately 5 MW fissioning uranium plasma experiment. A preliminary design is described for an argon buffer gas confined, UF6 flow loop system for future use in flowing critical experiments. Initial calculations to estimate the operating characteristics of the gaseous fissioning UF6 in a confined flow test at a pressure of 4 atm, indicate temperature increases of approximately 100 and 1000 K in the UF6 may be obtained for total test power levels of 100 kW and 1 MW for test times of 320 and 32 sec, respectively.

Pyrotechnic hazards classification and evaluation program. Phase 2, segment 3: Test plan for determining hazards associated with pyrotechnic manufacturing processes

NASA Technical Reports Server (NTRS)

1971-01-01

A comprehensive test plan for determining the hazards associated with pyrotechnic manufacturing processes is presented. The rationale for each test is based on a systematic analysis of historical accounts of accidents and a detailed study of the characteristics of each manufacturing process. The most hazardous manufacturing operations have been determined to be pressing, mixing, reaming, and filling. The hazard potential of a given situation is evaluated in terms of the probabilities of initiation, communication, and transition to detonation (ICT). The characteristics which affect the ICT probabilities include the ignition mechanisms which are present either in normal or abnormal operation, the condition and properties of the pyrotechnic material, and the configuration of the processing equipment. Analytic expressions are derived which describe the physical conditions of the system, thus permitting a variety of processes to be evaluated in terms of a small number of experiments.

Comments on some of the drilling and completion problems in Cerro Prieto geothermal wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dominguez A, B.; Sanchez G, G.

From 1960 to the present, 85 wells with a total drilling length exceeding 160,000 m have been constructed at Cerro Prieto, a modest figure compared to an oil field. This activity took place in five stages, each characterized by changes and modifications required by various drilling and well-completion problems. Initially, the technical procedures followed were similar to those used in the oil industry. However, several problems emerged as a result of the relatively high temperatures found in the geothermal reservoir. The various problems that have been encountered can be considered to be related to drilling fluids, cements and cementing operations,more » lithology, geothermal fluid characteristics, and casings and their accessories. As the importance of high temperatures and the characteristics of the geothermal reservoir fluids were better understood, the criteria were modified to optimize well-completion operations, and satisfactory results have been achieved to date.« less

Demand for large freighter aircraft as projected by the NASA cargo/logistics airlift system studies

NASA Technical Reports Server (NTRS)

Whitehead, A. H., Jr.; Kuhlman, W. H.

1979-01-01

The market conditions are examined up through the year 2008 to provide a preliminary assessment of the potential for and the characteristics of an advanced, all-cargo transport aircraft. Any new freighter must compete with current wide-body aircraft and their derivatives. Aircraft larger than the wide-bodies may incur economic penalties and operational problems. A lower direct operating cost is not a sufficient criterion to base a decision for the initiation of a new aircraft development or to select aircraft characteristics. Other factors of equal importance that are reviewed in this paper include considerations of the system infrastructure, the economics of the airlines, and the aircraft manufacturer return on investment. The results of the market forecast and a computer simulation show that an advanced long range aircraft with a payload between 68 to 181 tonnes (75 to 200 tons) could generate a solid foothold beginning around 1994.

Effects of Two Physical Training Paradigms on Biological and Cognitive Characteristics of Airmen: Lessons Learned

DTIC Science & Technology

2017-06-07

a 9- week physical training program, tests of physical endurance and strength , body composition analyses, biomarker collections, and cognitive tests...BDNF results to improving training , a new laboratory capability within RHCP was needed, coupled with an initial operational pilot test of that...traditional AF fitness training and that the improvements in cognitive performance would be correlated with changes in BDNF levels. Specifically, the

Advanced electrodes for AMTEC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiebig, Brad; Schuller, Michael; Hudson, Patricia

1999-01-01

Texas A&M University has begun an investigation of materials and fabrication methods which will improve AMTEC electrode performance. The study currently involves gathering data on materials which meet the basic requirements of operating in an AMTEC cell, and sorting out candidates possessing characteristics conducive to efficient AMTEC operation. An initial assessment has shown Iridium as a promising metal electrode candidate. Sodium-containing double-oxides, with melting temperatures above AMTEC operating temperatures, including NaNbO{sub 3} and Na{sub 2}Ti{sub 3}O{sub 7}, have been identified as possible electrode dopants, to enhance the sodium conductivity of an electrode. Photo-deposition and Evaporative-deposition will be investigated further asmore » electrode fabrication techniques. {copyright} {ital 1999 American Institute of Physics.}« less

Assessment of Durable SiC JFET Technology for +600 C to -125 C Integrated Circuit Operation

NASA Technical Reports Server (NTRS)

Neudeck, P. G.; Krasowski, M. J.; Prokop, N. F.

2011-01-01

Electrical characteristics and circuit design considerations for prototype 6H-SiC JFET integrated circuits (ICs) operating over the broad temperature range of -125 C to +600 C are described. Strategic implementation of circuits with transistors and resistors in the same 6H-SiC n-channel layer enabled ICs with nearly temperature-independent functionality to be achieved. The frequency performance of the circuits declined at temperatures increasingly below or above room temperature, roughly corresponding to the change in 6H-SiC n-channel resistance arising from incomplete carrier ionization at low temperature and decreased electron mobility at high temperature. In addition to very broad temperature functionality, these simple digital and analog demonstration integrated circuits successfully operated with little change in functional characteristics over the course of thousands of hours at 500 C before experiencing interconnect-related failures. With appropriate further development, these initial results establish a new technology foundation for realizing durable 500 C ICs for combustion engine sensing and control, deep-well drilling, and other harsh-environment applications.

Helicopter gust response characteristics including unsteady aerodynamic stall effects

NASA Technical Reports Server (NTRS)

Arcidiacono, P. J.; Bergquist, R. R.; Alexander, W. T., Jr.

1974-01-01

The results of an analytical study to evaluate the general response characteristics of a helicopter subjected to various types of discrete gust encounters are presented. The analysis employed was a nonlinear coupled, multi-blade rotorfuselage analysis including the effects of blade flexibility and unsteady aerodynamic stall. Only the controls-fixed response of the basic aircraft without any aircraft stability augmentation was considered. A discussion of the basic differences between gust sensitivity of fixed and rotary wing aircraft is presented. The effects of several rotor configuration and aircraft operating parameters on initial gust-induced load factor and blade vibratory stress and pushrod loads are discussed.

Preliminary development of digital signal processing in microwave radiometers

NASA Technical Reports Server (NTRS)

Stanley, W. D.

1980-01-01

Topics covered involve a number of closely related tasks including: the development of several control loop and dynamic noise model computer programs for simulating microwave radiometer measurements; computer modeling of an existing stepped frequency radiometer in an effort to determine its optimum operational characteristics; investigation of the classical second order analog control loop to determine its ability to reduce the estimation error in a microwave radiometer; investigation of several digital signal processing unit designs; initiation of efforts to develop required hardware and software for implementation of the digital signal processing unit; and investigation of the general characteristics and peculiarities of digital processing noiselike microwave radiometer signals.

Sprint: The first flight demonstration of the external work system robots

NASA Technical Reports Server (NTRS)

Price, Charles R.; Grimm, Keith

1995-01-01

The External Works Systems (EWS) 'X Program' is a new NASA initiative that will, in the next ten years, develop a new generation of space robots for active and participative support of zero g external operations. The robotic development will center on three areas: the assistant robot, the associate robot, and the surrogate robot that will support external vehicular activities (EVA) prior to and after, during, and instead of space-suited human external activities respectively. The EWS robotics program will be a combination of technology developments and flight demonstrations for operational proof of concept. The first EWS flight will be a flying camera called 'Sprint' that will seek to demonstrate operationally flexible, remote viewing capability for EVA operations, inspections, and contingencies for the space shuttle and space station. This paper describes the need for Sprint and its characteristics.

Study of laser heated propulsion devices. Part 1: Evaluation of laser devices, fuels and energy coupling mechanisms

NASA Technical Reports Server (NTRS)

Hofer, O. C.

1982-01-01

Closed cycle, CW waveform and short wavelength laser devices are desirable characteristics for laser propulsion. The choice of specific wavelengths for hydrogen fuel affects the operational conditions under which a laser supported absorption (LSA) wave is initiated and maintained. The mechanisms of initiating and maintaining LSA waves depend on the wavelength of the laser. Consequently, the shape and size of the hot core plasma is also dependent on wavelength and pressure. Detailed modeling of these mechanisms must be performed before their actual significance can be ascertained. Inverse bremsstrahlung absorption mechanism is the dominant mechanism for coupling energy into the plasma, but other mechanisms which are wavelength dependent can dictate the LSA wave plasma initiation and maintenance conditions. Multiphoton mechanisms become important at visible or shorter wavelengths. These are important mechanisms in creating the initial H2 gas breakdown and supplying the precursor electrons required to sustain the plasma.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klein, Steven Karl; Determan, John C.

Dynamic System Simulation (DSS) models of fissile solution systems have been developed and verified against a variety of historical configurations. DSS techniques have been applied specifically to subcritical accelerator-driven systems using fissile solution fuels of uranium. Initial DSS models were developed in DESIRE, a specialized simulation scripting language. In order to tailor the DSS models to specifically meet needs of system designers they were converted to a Visual Studio implementation, and one of these subsequently to National Instrument’s LabVIEW for human factors engineering and operator training. Specific operational characteristics of subcritical accelerator-driven systems have been examined using a DSS modelmore » tailored to this particular class using fissile fuel.« less

Apply TQM to E-Government Outsourcing Management

NASA Astrophysics Data System (ADS)

Huai, Jinmei

This paper developed an approach to e-government outsourcing quality management. E-government initiatives have rapidly increased in the last decades and the success of these activities will largely depend on their operation quality. As an instrument to improve operation quality, outsourcing can be applied to e-government. This paper inspected process of e-government outsourcing and discussed how to improve the outsourcing performance through total quality management (TQM). The characteristics and special requirements of e-government outsourcing were analyzed as the basis for discussion. Then the principles and application of total quality management were interpreted. Finally the process of improving performance of e-government was analyzed in the context of outsourcing.

Benthic Faunal Colonization of an Offshore Borrow Pit in Southeastern Florida. Dredging Operations Technical Support Program

DTIC Science & Technology

1988-10-01

180 and 30* C, while water salinities vary between 33 and 37 ppt, depending primarily on seasonal rainfall patterns and discharge through local inlets...strategists are characteristically small-bodied, short-lived, and have high fecundity, efficient dispersal mechanisms , and rapid growth rates. Species... mechanisms , and slow growth rates. Recolonization of a disturbed area is thus generally initiated by r-strategists. Theoretically, r-selected species

Department of Defense Onsite Child Care Initiative. Hearing before a Subcommittee of the Committee on Government Operations. House of Representatives, One Hundredth Congress, First Session.

ERIC Educational Resources Information Center

Congress of the U. S., Washington, DC. House Committee on Government Operations.

A hearing was held to examine the Department of Defense's on-site child care policies for uniformed and civilian personnel. Testimony concerned: (1) origins of the need for on-site or near-site child care among military personnel and characteristics of care provided; (2) aspects of service provision to civilian personnel working for the military…

Permafrost Ecosystem Warming Prototype: Installation, Operation, and Initial Site Characterization

DTIC Science & Technology

2013-11-01

report Approved for public release; distribution is unlimited. Prepared for US Army Corps of Engineers Washington , DC 20314-1000 Monitored by...in 3 m diameter plots in a temperate deciduous forest. To further develop the prototype for an arctic climate, a similar test system was installed...growth trees and shrubs. The site was chosen because of its permafrost characteristics, ease of access, and its close proximity to the CRREL Fairbanks

Operational Design Cognitive Methodology: An Analysis of COMISAF 30 August 2009 Initial Assessment

DTIC Science & Technology

2010-04-01

the set of characteristics, capabilities, and sources of power from which a system derives its moral or physical strength, freedom of action, and...objective must be the population.” 53 The population focused objective extends beyond just the basics of physical security. The whole of government...In Warfare Studies AY10 Coursebook , edited by Sharon McBride, 196-212. Maxwell AFB, AL: Air University Press, October 2009. Kem, Jack D

THE ARMOUR DUST FUELED REACTOR (ADFR)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krucoff, D.

1958-01-01

The A-DFR is based on the use of a fissionable dust carried in a gas. This fuel ferm offers promise of a major economic advance through the use of 2,000 to 3,000 F operating temperatures and a low cost fuel cycle. The development program is described that was initiated to investigate experimentally the proposed fuel and study analytically other reactor characteristics. A brief review of the reactor concept is presented. (W.D.M.)

Contemporary post surgical management of differentiated thyroid carcinoma.

PubMed

Tala, H; Tuttle, R M

2010-08-01

Risk assessment is the cornerstone of contemporary management of thyroid cancer. Following thyroid surgery, an initial risk assessment of recurrence and disease-specific mortality is made using important intra-operative findings, histologic characteristics of the tumor, molecular profile of the tumor, post-operative serum thyroglobulin and any available cross-sectional imaging studies. This initial risk assessment is used to guide recommendations regarding the need for remnant ablation, external beam irradiation, systemic therapy, degree of TSH suppression, and follow-up disease detection strategy over the first 2 years after initial therapy. While this initial risk stratification provides valuable information, it is a static representation of the patient in the first few weeks post-operatively that does not change over time. Depending on how the patient responds to our initial therapies, the risk of recurrence and death may change significantly during follow-up. In order to account for differences in response to therapy in individual patients and to incorporate the impact of treatment on our initial risk estimates, we recommend a re-stratification of risk at the 2-year point of follow-up. This re-stratification provides an updated risk estimate that can be used to guide ongoing management recommendations including the frequency and intensity of follow-up, degree of ongoing TSH suppression, and need for additional therapies. Ongoing management recommendations must be tailored to realistic, evolving risk estimates that are actively updated during follow-up. By individualizing therapy on the basis of initial and ongoing risk assessments, we can maximize the beneficial effects of aggressive therapy in patients with thyroid cancer who are likely to benefit from it, while minimizing potential complications and side effects in low-risk patients destined to have a full healthy and productive life after minimal therapeutic intervention. Copyright (c) 2010 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

Whole-Lesion Apparent Diffusion Coefficient-Based Entropy-Related Parameters for Characterizing Cervical Cancers: Initial Findings.

PubMed

Guan, Yue; Li, Weifeng; Jiang, Zhuoran; Chen, Ying; Liu, Song; He, Jian; Zhou, Zhengyang; Ge, Yun

2016-12-01

This study aimed to develop whole-lesion apparent diffusion coefficient (ADC)-based entropy-related parameters of cervical cancer to preliminarily assess intratumoral heterogeneity of this lesion in comparison to adjacent normal cervical tissues. A total of 51 women (mean age, 49 years) with cervical cancers confirmed by biopsy underwent 3-T pelvic diffusion-weighted magnetic resonance imaging with b values of 0 and 800 s/mm 2 prospectively. ADC-based entropy-related parameters including first-order entropy and second-order entropies were derived from the whole tumor volume as well as adjacent normal cervical tissues. Intraclass correlation coefficient, Wilcoxon test with Bonferroni correction, Kruskal-Wallis test, and receiver operating characteristic curve were used for statistical analysis. All the parameters showed excellent interobserver agreement (all intraclass correlation coefficients  > 0.900). Entropy, entropy(H) 0 , entropy(H) 45 , entropy(H) 90 , entropy(H) 135 , and entropy(H) mean were significantly higher, whereas entropy(H) range and entropy(H) std were significantly lower in cervical cancers compared to adjacent normal cervical tissues (all P <.0001). Kruskal-Wallis test showed that there were no significant differences among the values of various second-order entropies including entropy(H) 0, entropy(H) 45 , entropy(H) 90 , entropy(H) 135 , and entropy(H) mean. All second-order entropies had larger area under the receiver operating characteristic curve than first-order entropy in differentiating cervical cancers from adjacent normal cervical tissues. Further, entropy(H) 45 , entropy(H) 90 , entropy(H) 135 , and entropy(H) mean had the same largest area under the receiver operating characteristic curve of 0.867. Whole-lesion ADC-based entropy-related parameters of cervical cancers were developed successfully, which showed initial potential in characterizing intratumoral heterogeneity in comparison to adjacent normal cervical tissues. Copyright © 2016 The Association of University Radiologists. Published by Elsevier Inc. All rights reserved.

Automation of a Versatile Crane (the LSMS) for Lunar Outpost Construction, Maintenance and Inspection

NASA Technical Reports Server (NTRS)

Doggett, William R.; Roithmayr, Carlos M.; Dorsey, John T.; Jones, Thomas C.; Shen, Haijun; Seywald, Hans; King, Bruce D.; Mikulas, Martin M., Jr.

2009-01-01

Devices for lifting, translating and precisely placing payloads are critical for efficient Earth-based construction operations. Both recent and past studies have demonstrated that devices with similar functionality will be needed to support lunar outpost operations. Although several designs have been developed for Earth based applications, these devices lack unique design characteristics necessary for transport to and use on the harsh lunar surface. These design characteristics include: a) lightweight components, b) compact packaging for launch, c) automated deployment, d) simple in-field reconfiguration and repair, and e) support for tele-operated or automated operations. Also, because the cost to transport mass to the lunar surface is very high, the number of devices that can be dedicated to surface operations will be limited. Thus, in contrast to Earth-based construction, where many single-purpose devices dominate a construction site, a lunar outpost will require a limited number of versatile devices that provide operational benefit from initial construction through sustained operations. The first generation test-bed of a new high performance device, the Lunar Surface Manipulation System (LSMS) has been designed, built and field tested. The LSMS has many unique features resulting in a mass efficient solution to payload handling on the lunar surface. Typically, the LSMS device mass is estimated at approximately 3% of the mass of the heaviest payload lifted at the tip, or 1.8 % of the mass of the heaviest mass lifted at the elbow or mid-span of the boom for a high performance variant incorporating advanced structural components. Initial operational capabilities of the LSMS were successfully demonstrated during field tests at Moses Lake, Washington using a tele-operated approach. Joint angle sensors have been developed for the LSMS to improve operator situational awareness. These same sensors provide the necessary information to support fully automated operations, greatly expanding the operational versatility of the LSMS. This paper develops the equations describing the forward and inverse relation between LSMS joint angles and Cartesian coordinates of the LSMS tip. These equations allow a variety of schemes to be used to maneuver the LSMS to optimize the maneuver. One such scheme will be described in detail that eliminates undesirable swinging of the payload at the conclusion of a maneuver, even when the payload is suspended from a passive rigid link. The swinging is undesirable when performing precision maneuvers, such as aligning an object for mating or positioning a camera. Use of the equations described here enables automated control of the LSMS greatly improving its operational versatility.

High Tumor Volume to Fetal Weight Ratio Is Associated with Worse Fetal Outcomes and Increased Maternal Risk in Fetuses with Sacrococcygeal Teratoma.

PubMed

Gebb, Juliana S; Khalek, Nahla; Qamar, Huma; Johnson, Mark P; Oliver, Edward R; Coleman, Beverly G; Peranteau, William H; Hedrick, Holly L; Flake, Alan W; Adzick, N Scott; Moldenhauer, Julie S

2018-03-01

Tumor volume to fetal weight ratio (TFR) > 0.12 before 24 weeks has been associated with poor outcome in fetuses with sacrococcygeal teratoma (SCT). We evaluated TFR in predicting poor fetal outcome and increased maternal operative risk in our cohort of SCT pregnancies. This is a retrospective, single-center review of fetuses seen with SCT from 1997 to 2015. Patients who chose termination of pregnancy (TOP), delivered elsewhere, or had initial evaluation at > 24 weeks were excluded. Receiver operating characteristic (ROC) analysis determined the optimal TFR to predict poor fetal outcome and increased maternal operative risk. Poor fetal outcome included fetal demise, neonatal demise, or fetal deterioration warranting open fetal surgery or delivery < 32 weeks. Increased maternal operative risk included cases necessitating open fetal surgery, classical cesarean delivery, or ex utero intrapartum treatment (EXIT). Of 139 pregnancies with SCT, 27 chose TOP, 14 delivered elsewhere, and 40 had initial evaluation at > 24 weeks. Thus, 58 fetuses were reviewed. ROC analysis revealed that at ≤24 weeks, TFR > 0.095 was predictive of poor fetal outcome and TFR > 0.12 was predictive of increased maternal operative risk. This study supports the use of TFR at ≤24 weeks for risk stratification of pregnancies with SCT. © 2018 S. Karger AG, Basel.

Frost characteristics and heat transfer on a flat plate under freezer operating conditions: Part 1, Experimentation and correlations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mao, Y.; Besant, R.W.; Chen, H.

1999-07-01

An experimental investigation of frost growth on a flat, cold surface supplied by subfreezing, turbulent, humid, parallel flow of air is presented. The operating conditions are typical of many commercial freezers. A test loop was constructed to perform the tests, and the frost height, frost mass concentration, and cold surface heat flux were measured using specially designed and calibrated instrumentation. Twenty tests were done for steady operating conditions, each starting with no initial frost accumulation, and were run for two to six hours giving 480 data samples. Measured results show that the frost characteristics differ significantly with frost growth datamore » taken previously for room temperature airflow. Depending on the temperature of the cold plate and the relative humidity of the subfreezing supply air, the frost could appear to be either smooth or rough. Smooth frost, which occurred at warmer plate temperatures and lower supply air relative humidities, gave rise to frost growth that was much thinner and denser than that for the rough, thick, low-density frost. Frost growth characteristics are correlated as a function of five independent variables (time, distance from the leading edge, cold plate temperature ratio, humidity ratio, and Reynolds number). These correlations are presented separately for the full data set, the rough frost data, and the smooth frost data.« less

Studies on biogas-fuelled compression ignition engine under dual fuel mode.

PubMed

Mahla, Sunil Kumar; Singla, Varun; Sandhu, Sarbjot Singh; Dhir, Amit

2018-04-01

Experimental investigation has been carried out to utilize biogas as an alternative source of energy in compression ignition (CI) engine under dual fuel operational mode. Biogas was inducted into the inlet manifold at different flow rates along with fresh air through inlet manifold and diesel was injected as a pilot fuel to initiate combustion under dual fuel mode. The engine performance and emission characteristics of dual fuel operational mode were analyzed at different biogas flow rates and compared with baseline conventional diesel fuel. Based upon the improved performance and lower emission characteristics under the dual fuel operation, the optimum flow rate of biogas was observed to be 2.2 kg/h. The lower brake thermal efficiency (BTE) and higher brake-specific energy consumption (BSEC) were noticed with biogas-diesel fuel under dual fuel mode when compared with neat diesel operation. Test results showed reduced NO x emissions and smoke opacity level in the exhaust tailpipe emissions. However, higher hydrocarbon (HC) and carbon monoxide (CO) emissions were noticed under dual fuel mode at entire engine loads when compared with baseline fossil petro-diesel. Hence, the use of low-cost gaseous fuel such as biogas would be an economically viable proposition to address the current and future problems of energy scarcity and associated environmental concerns.

Patient profiling can identify patients with adult spinal deformity (ASD) at risk for conversion from nonoperative to surgical treatment: initial steps to reduce ineffective ASD management.

PubMed

Passias, Peter G; Jalai, Cyrus M; Line, Breton G; Poorman, Gregory W; Scheer, Justin K; Smith, Justin S; Shaffrey, Christopher I; Burton, Douglas C; Fu, Kai-Ming G; Klineberg, Eric O; Hart, Robert A; Schwab, Frank; Lafage, Virginie; Bess, Shay

2018-02-01

Non-operative management is a common initial treatment for patients with adult spinal deformity (ASD) despite reported superiority of surgery with regard to outcomes. Ineffective medical care is a large source of resource drain on the health system. Characterization of patients with ASD likely to elect for operative treatment from non-operative management may allow for more efficient patient counseling and cost savings. This study aimed to identify deformity and disability characteristics of patients with ASD who ultimately convert to operative treatment compared with those who remain non-operative and those who initially choose surgery. A retrospective review was carried out. A total of 510 patients with ASD (189 non-operative, 321 operative) with minimum 2-year follow-up comprised the patient sample. Oswestry Disability Index (ODI), Short-Form 36 Health Assessment (SF-36), Scoliosis Research Society questionnaire (SRS-22r), and spinopelvic radiographic alignment were the outcome measures. Demographic, radiographic, and patient-reported outcome measures (PROMs) from a cohort of patients with ASD prospectively enrolled into a multicenter database were evaluated. Patients were divided into three treatment cohorts: Non-operative (NON=initial non-operative treatment and remained non-operative), Operative (OP=initial operative treatment), and Crossover (CROSS=initial non-operative treatment with subsequent conversion to operative treatment). NON and OP groups were propensity score-matched (PSM) to CROSS for baseline demographics (age, body mass index, Charlson Comorbidity Index). Time to crossover was divided into early (<1 year) and late (>1 year). Outcome measures were compared across and within treatment groups at four time points (baseline, 6 weeks, 1 year, and 2 years). Following PSM, 118 patients were included (NON=39, OP=38, CROSS=41). Crossover rate was 21.7% (41/189). Mean time to crossover was 394 days. All groups had similar baseline sagittal alignment, but CROSS had larger pelvic incidence and lumbar lordosis (PI-LL) mismatch than NON (11.9° vs. 3.1°, p=.032). CROSS and OP had similar baseline PROM scores; however, CROSS had worse baseline ODI, PCS, SRS-22r (p<.05). At time of crossover, CROSS had worse ODI (35.7 vs. 27.8) and SRS Satisfaction (2.6 vs. 3.3) compared with NON (p<.05). Alignment remained similar for CROSS from baseline to conversion; however, PROMs (ODI, PCS, SRS Activity/Pain/Total) worsened (p<.05). Early and late crossover evaluation demonstrated CROSS-early (n=25) had worsening ODI, SRS Activity/Pain at time of crossover (p<.05). From time of crossover to 2-year follow-up, CROSS-early had less SRS Appearance/Mental improvement compared with OP. Both CROSS-early/late had worse baseline, but greater improvements, in ODI, PCS, SRS Pain/Total compared with NON (p<.05). Baseline alignment and disability parameters increased crossover odds-Non with Schwab T/L/D curves and ODI≥40 (odds ratio [OR]: 3.05, p=.031), and Non with high PI-LL modifier grades ("+"/'++') and ODI≥40 (OR: 5.57, p=.007) were at increased crossover risk. High baseline and increasing disability over time drives conversion from non-operative to operative ASD care. CROSS patients had similar spinal deformity but worse PROMs than NON. CROSS achieved similar 2-year outcome scores as OP. Profiling at first visit for patients at risk of crossover may optimize physician counseling and cost savings. Copyright © 2017. Published by Elsevier Inc.

Robot dynamics in reduced gravity environment

NASA Technical Reports Server (NTRS)

Workman, Gary L.; Grisham, Tollie; Hinman, Elaine; Coker, Cindy

1990-01-01

Robot dynamics and control will become an important issue for productive platforms in space. Robotic operations will be necessary for both man tended stations and for the efficient performance of routine operations in a manned platform. The current constraints on the use of robotic devices in a microgravity environment appears to be due to safety concerns and an anticipated increase in acceleration levels due to manipulator motion. The robot used for the initial studies was a UMI RTX robot, which was adapted to operate in a materials processing workcell to simulate sample changing in a microgravity environment. The robotic cell was flown several times on the KC-135 aircraft at Ellington Field. The primary objective of the initial flights was to determine operating characteristics of both the robot and the operator in the variable gravity of the KC-135 during parabolic maneuvers. It was demonstrated that the KC-135 aircraft can be used for observing dynamics of robotic manipulators. The difficulties associated with humans performing teleoperation tasks during varying G levels were also observed and can provide insight into some areas in which the use of artificial techniques would provide improved system performance. Additionally a graphic simulation of the workcell was developed on a Silicon Graphics Workstation using the IGRIP simulation language from Deneb Robotics. The simulation is intended to be used for predictive displays of the robot operating on the aircraft. It is also anticipated that this simulation can be useful for off-line programming of tasks in the future.

Evidence based diagnosis and management of chronic subdural hematoma: A review of the literature.

PubMed

Mehta, Vikram; Harward, Stephen C; Sankey, Eric W; Nayar, Gautam; Codd, Patrick J

2018-04-01

Chronic subdural hematomas are encapsulated blood collections within the dural border cells with characteristic outer "neomembranes". Affected patients are more often male and typically above the age of 70. Imaging shows crescentic layering of fluid in the subdural space on a non-contrast computed tomography (CT) scan, best appreciated on sagittal or coronal reformats. Initial medical management involves reversing anticoagulant/antiplatelet therapies, and often initiation of anti-epileptic drugs (AEDs). Operative interventions, such as twist-drill craniostomy (TDC), burr-hole craniostomy (BHC), and craniotomy are indicated if imaging implies compression (maximum fluid collection thickness >1 cm) or the patient is symptomatic. The effectiveness of various surgical techniques remains poorly characterized, with sparse level 1 evidence, variable outcome measures, and various surgical techniques. Postoperatively, subdural drains can decrease recurrence and sequential compression devices can decrease embolic complications, while measures such as early mobilization and re-initiation of anticoagulation need further study. Non-operative management, including steroid therapy, etizolam, tranexamic acid, and angiotensin converting enzyme inhibitors (ACEI) also remain poorly studied. Recurrent hemorrhages are a major complication affecting around 10-20% of patients, and therefore close follow-up is essential. Copyright © 2018 Elsevier Ltd. All rights reserved.

Selection of the initial design for the two-stage continual reassessment method.

PubMed

Jia, Xiaoyu; Ivanova, Anastasia; Lee, Shing M

2017-01-01

In the two-stage continual reassessment method (CRM), model-based dose escalation is preceded by a pre-specified escalating sequence starting from the lowest dose level. This is appealing to clinicians because it allows a sufficient number of patients to be assigned to each of the lower dose levels before escalating to higher dose levels. While a theoretical framework to build the two-stage CRM has been proposed, the selection of the initial dose-escalating sequence, generally referred to as the initial design, remains arbitrary, either by specifying cohorts of three patients or by trial and error through extensive simulations. Motivated by a currently ongoing oncology dose-finding study for which clinicians explicitly stated their desire to assign at least one patient to each of the lower dose levels, we proposed a systematic approach for selecting the initial design for the two-stage CRM. The initial design obtained using the proposed algorithm yields better operating characteristics compared to using a cohort of three initial design with a calibrated CRM. The proposed algorithm simplifies the selection of initial design for the two-stage CRM. Moreover, initial designs to be used as reference for planning a two-stage CRM are provided.

Robotic Missions to Small Bodies and Their Potential Contributions to Human Exploration and Planetary Defense

NASA Technical Reports Server (NTRS)

Abell, Paul A.; Rivkin, Andrew S.

2015-01-01

Introduction: Robotic missions to small bodies will directly address aspects of NASA's Asteroid Initiative and will contribute to future human exploration and planetary defense. The NASA Asteroid Initiative is comprised of two major components: the Grand Challenge and the Asteroid Mission. The first component, the Grand Challenge, focuses on protecting Earth's population from asteroid impacts by detecting potentially hazardous objects with enough warning time to either prevent them from impacting the planet, or to implement civil defense procedures. The Asteroid Mission involves sending astronauts to study and sample a near-Earth asteroid (NEA) prior to conducting exploration missions of the Martian system, which includes Phobos and Deimos. The science and technical data obtained from robotic precursor missions that investigate the surface and interior physical characteristics of an object will help identify the pertinent physical properties that will maximize operational efficiency and reduce mission risk for both robotic assets and crew operating in close proximity to, or at the surface of, a small body. These data will help fill crucial strategic knowledge gaps (SKGs) concerning asteroid physical characteristics that are relevant for human exploration considerations at similar small body destinations. These data can also be applied for gaining an understanding of pertinent small body physical characteristics that would also be beneficial for formulating future impact mitigation procedures. Small Body Strategic Knowledge Gaps: For the past several years NASA has been interested in identifying the key SKGs related to future human destinations. These SKGs highlight the various unknowns and/or data gaps of targets that the science and engineering communities would like to have filled in prior to committing crews to explore the Solar System. An action team from the Small Bodies Assessment Group (SBAG) was formed specifically to identify the small body SKGs under the direction of the Human Exploration and Operations Missions Directorate (HEOMD), given NASA's recent interest in NEAs and the Martian moons as potential human destinations. The action team organized the SKGs into four broad themes: 1) Identify human mission targets; 2) Understand how to work on and interact with the small body surface; 3) Understand the small body environment and its potential risk/benefit to crew, systems, and operational assets; and 4) Understand the small body resource potential. Of these four SKG themes, the first three have significant overlap with planetary defense considerations. The data obtained from investigations of small body physical characteristics under these three themes can be directly applicable to planetary defense initiatives. Conclusions: Missions to investigate small bodies can address small body strategic knowledge gaps and contribute to the overall success for human exploration missions to asteroids and the Martian moons. In addition, such reconnaissance of small bodies can also provide a wealth of information relevant to the science and planetary defense of NEAs.

Dynamic response characteristics of the high-temperature superconducting maglev system under lateral eccentric distance

NASA Astrophysics Data System (ADS)

Wang, Bo; Zheng, Jun; Si, Shuaishuai; Qian, Nan; Li, Haitao; Li, Jipeng; Deng, Zigang

2016-07-01

Off-centre operation of high-temperature superconducting (HTS) maglev systems caused by inevitable conditions such as the misregistration of vehicle, crosswind and curve negotiation, may change the distribution of the trapped flux in the HTS bulks and the magnetic interaction between HTS bulks and the PMG. It impacts on the performance of HTS maglev, and more seriously makes the maglev vehicle overturned. Therefore, understanding the performance of the HTS maglev in off-center operation is very important. In this paper, the dynamic response characteristics of a cryostat with twenty-four onboard YBaCuO superconductor bulks were experimentally investigated at different eccentric distances under loads before the initial FC process. Parameters such as vibration accelerations, displacement, natural frequency and dynamic stiffness were acquired and analyzed via the B&K vibration analyzer and laser displacement sensors. Results suggest that the natural frequency and dynamic stiffness of the maglev vehicle would be obviously reduced with the eccentric distance, posing negative effects on the stability of HTS maglev.

Mathematical Model of the One-stage Magneto-optical Sensor Based on Faraday Effect

NASA Astrophysics Data System (ADS)

Babaev, O. G.; Paranin, V. D.; Sinitsin, L. I.

2018-01-01

The aim of this work is to refine a model of magneto-optical sensors based on Faraday’s longitudinal magneto-optical effect. The tasks of the study include computer modeling and analysis of the transfer characteristic of a single-stage magneto-optical sensor for various polarization of the input beam and non-ideal optical components. The proposed mathematical model and software make it possible to take into account the non-ideal characteristics of film polaroids observed in operation in the near infrared region and at increased temperatures. On the basis of the results of the model analysis it was found that the dependence of normalized transmission T(γ2) has periodic nature. Choosing the angle (γ 2-γ 1) makes it possible to shift the initial operation point and change the sensitivity dT/dγ 2. The influence of the input beam polarization increases with the increase of polaroid parameter deviation from ideal and shows itself as reduction of modulation depth and angular shift of the sensor conversion response.

Aircraft accident investigation: the decision-making in initial action scenario.

PubMed

Barreto, Marcia M; Ribeiro, Selma L O

2012-01-01

In the complex aeronautical environment, the efforts in terms of operational safety involve the adoption of proactive and reactive measures. The process of investigation begins right after the occurrence of the aeronautical accident, through the initial action. Thus, it is in the crisis scenario, that the person responsible for the initial action makes decisions and gathers the necessary information for the subsequent phases of the investigation process. Within this scenario, which is a natural environment, researches have shown the fragility of rational models of decision making. The theoretical perspective of naturalistic decision making constitutes a breakthrough in the understanding of decision problems demanded by real world. The proposal of this study was to verify if the initial action, after the occurrence of an accident, and the decision-making strategies, used by the investigators responsible for this activity, are characteristic of the naturalistic decision making theoretical approach. To attend the proposed objective a descriptive research was undertaken with a sample of professionals that work in this activity. The data collected through individual interviews were analyzed and the results demonstrated that the initial action environment, which includes restricted time, dynamic conditions, the presence of multiple actors, stress and insufficient information is characteristic of the naturalistic decision making. They also demonstrated that, when the investigators make their decisions, they use their experience and the mental simulation, intuition, improvisation, metaphors and analogues cases, as strategies, all of them related to the naturalistic approach of decision making, in order to satisfy the needs of the situation and reach the objectives of the initial action in the accident scenario.

Foldable and Disposable Memory on Paper

PubMed Central

Lee, Byung-Hyun; Lee, Dong-Il; Bae, Hagyoul; Seong, Hyejeong; Jeon, Seung-Bae; Seol, Myung-Lok; Han, Jin-Woo; Meyyappan, M.; Im, Sung-Gap; Choi, Yang-Kyu

2016-01-01

Foldable organic memory on cellulose nanofibril paper with bendable and rollable characteristics is demonstrated by employing initiated chemical vapor deposition (iCVD) for polymerization of the resistive switching layer and inkjet printing of the electrode, where iCVD based on all-dry and room temperature process is very suitable for paper electronics. This memory exhibits a low operation voltage of 1.5 V enabling battery operation compared to previous reports and wide memory window. The memory performance is maintained after folding tests, showing high endurance. Furthermore, the quick and complete disposable nature demonstrated here is attractive for security applications. This work provides an effective platform for green, foldable and disposable electronics based on low cost and versatile materials. PMID:27922094

In situ FBG inscription during fiber laser operation.

PubMed

Leich, Martin; Fiebrandt, Julia; Jetschke, Sylvia; Rothhardt, Manfred; Jäger, Matthias

2013-03-01

We demonstrate the inscription of a 266 nm UV femtosecond pulse-induced fiber Bragg grating (FBG) in an Yb-doped fiber during optical pumping at 976 nm and the initiation of lasing with increasing grating reflectivity. Output spectra show the emission of the pumped fiber changing from the broad-ranged amplified spontaneous emission in the nonlasing case to the narrow-range laser operation due to the enhancement of FBG reflectivity during inscription. The proposed technique enables the direct characterization and control of FBG performance in fiber lasers. After FBG fabrication, we investigate the spectral characteristics of the fiber laser for different laser powers and study the influence of a thermal treatment of the FBG.

Virtual building environments (VBE) - Applying information modeling to buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bazjanac, Vladimir

2004-06-21

A Virtual Building Environment (VBE) is a ''place'' where building industry project staffs can get help in creating Building Information Models (BIM) and in the use of virtual buildings. It consists of a group of industry software that is operated by industry experts who are also experts in the use of that software. The purpose of a VBE is to facilitate expert use of appropriate software applications in conjunction with each other to efficiently support multidisciplinary work. This paper defines BIM and virtual buildings, and describes VBE objectives, set-up and characteristics of operation. It informs about the VBE Initiative andmore » the benefits from a couple of early VBE projects.« less

The NPP and J1 CrIS Operational High-Resolution Channel Selection for the NUCAPS algorithm: A demonstration of global applicability to meet users needs

NASA Astrophysics Data System (ADS)

Smith, J.; Gambacorta, A.; Barnet, C.; Smith, N.; Goldberg, M.; Pierce, B.; Wolf, W.; King, T.

2016-12-01

This work presents an overview of the NPP and J1 CrIS high resolution operational channel selection. Our methodology focuses on the spectral sensitivity characteristics of the available channels in order to maximize information content and spectral purity. These aspects are key to ensure accuracy in the retrieval products, particularly for trace gases. We will provide a demonstration of its global optimality by analyzing different test cases that are of particular interests to our JPSS Proving Ground and Risk Reduction user applications. A focus will be on high resolution trace gas retrieval capability in the context of the Alaska fire initiatives.

Reduced power processor requirements for the 30-cm diameter HG ion thruster

NASA Technical Reports Server (NTRS)

Rawlin, V. K.

1979-01-01

The characteristics of power processors strongly impact the overall performance and cost of electric propulsion systems. A program was initiated to evaluate simplifications of the thruster-power processor interface requirements. The power processor requirements are mission dependent with major differences arising for those missions which require a nearly constant thruster operating point (typical of geocentric and some inbound planetary missions) and those requiring operation over a large range of input power (such as outbound planetary missions). This paper describes the results of tests which have indicated that as many as seven of the twelve power supplies may be eliminated from the present Functional Model Power Processor used with 30-cm diameter Hg ion thrusters.

[Phenomenon of preoperative stress in patients with ischemic heart disease. Assessment of its clinical and prognostic significance].

PubMed

Barbarash, O L; Shabalina, L V; Bergen, E I; Guliaeva, E N; Barbarash, N A

1998-01-01

To assess preoperative stress in patients with ischemic heart disease (IHD) and its influence on the course of early intraoperative period. 79 patients scheduled for aortocoronary bypass operation were studied to assess the phenomenon of preoperative psychoemotional stress (clinical characteristics, personal anxiety, humoral and vegetative regulation. 24 hours before operation IHD patients became anxious, coronary insufficiency and arrhythmia aggravated as shown by Holter ECG monitoring. Initial insufficiency of the antioxidant system, disturbances of the platelet-vascular hemostasis, hyperlipidemia and dyslipoproteinemia enhanced. Preoperative changes due to stress reaction affected the course of early intraoperative period. It is necessary to apply individual schemes of stress-limiting preoperative preparation in IHD patients.

Schematic construction of flanged nanobearings from double-walled carbon nanotubes.

PubMed

Shenai, Prathamesh Mahesh; Zhao, Yang

2010-08-01

The performance of nanobearings constructed from double walled carbon nanotubes is considered to be crucially dependent on the initial rotational speed. Wearless rotation ceases for a nanobearing operating beyond a certain angular velocity. We propose a new design of nanobearings by manipulation of double walled carbon nanotubes leading to a flanged structure which possesses a built-in hindrance to the intertube oscillation without obstructing rotational motion. Through blocking the possible leakage path for rotational kinetic energy to the intertube oscillatory motion, the flanged bearing lowers its dissipative tendency when set into motion. Using molecular dynamics, it is shown that on account of its distinctive structure, the flanged bearing has superior operating characteristics and a broader working domain.

Comparison of initial perturbation methods for the mesoscale ensemble prediction system of the Meteorological Research Institute for the WWRP Beijing 2008 Olympics Research and Development Project (B08RDP)

NASA Astrophysics Data System (ADS)

Saito, Kazuo; Hara, Masahiro; Kunii, Masaru; Seko, Hiromu; Yamaguchi, Munehiko

2011-05-01

Different initial perturbation methods for the mesoscale ensemble prediction were compared by the Meteorological Research Institute (MRI) as a part of the intercomparison of mesoscale ensemble prediction systems (EPSs) of the World Weather Research Programme (WWRP) Beijing 2008 Olympics Research and Development Project (B08RDP). Five initial perturbation methods for mesoscale ensemble prediction were developed for B08RDP and compared at MRI: (1) a downscaling method of the Japan Meteorological Agency (JMA)'s operational one-week EPS (WEP), (2) a targeted global model singular vector (GSV) method, (3) a mesoscale model singular vector (MSV) method based on the adjoint model of the JMA non-hydrostatic model (NHM), (4) a mesoscale breeding growing mode (MBD) method based on the NHM forecast and (5) a local ensemble transform (LET) method based on the local ensemble transform Kalman filter (LETKF) using NHM. These perturbation methods were applied to the preliminary experiments of the B08RDP Tier-1 mesoscale ensemble prediction with a horizontal resolution of 15 km. To make the comparison easier, the same horizontal resolution (40 km) was employed for the three mesoscale model-based initial perturbation methods (MSV, MBD and LET). The GSV method completely outperformed the WEP method, confirming the advantage of targeting in mesoscale EPS. The GSV method generally performed well with regard to root mean square errors of the ensemble mean, large growth rates of ensemble spreads throughout the 36-h forecast period, and high detection rates and high Brier skill scores (BSSs) for weak rains. On the other hand, the mesoscale model-based initial perturbation methods showed good detection rates and BSSs for intense rains. The MSV method showed a rapid growth in the ensemble spread of precipitation up to a forecast time of 6 h, which suggests suitability of the mesoscale SV for short-range EPSs, but the initial large growth of the perturbation did not last long. The performance of the MBD method was good for ensemble prediction of intense rain with a relatively small computing cost. The LET method showed similar characteristics to the MBD method, but the spread and growth rate were slightly smaller and the relative operating characteristic area skill score and BSS did not surpass those of MBD. These characteristic features of the five methods were confirmed by checking the evolution of the total energy norms and their growth rates. Characteristics of the initial perturbations obtained by four methods (GSV, MSV, MBD and LET) were examined for the case of a synoptic low-pressure system passing over eastern China. With GSV and MSV, the regions of large spread were near the low-pressure system, but with MSV, the distribution was more concentrated on the mesoscale disturbance. On the other hand, large-spread areas were observed southwest of the disturbance in MBD and LET. The horizontal pattern of LET perturbation was similar to that of MBD, but the amplitude of the LET perturbation reflected the observation density.

Sensor Characteristics Reference Guide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cree, Johnathan V.; Dansu, A.; Fuhr, P.

The Buildings Technologies Office (BTO), within the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), is initiating a new program in Sensor and Controls. The vision of this program is: • Buildings operating automatically and continuously at peak energy efficiency over their lifetimes and interoperating effectively with the electric power grid. • Buildings that are self-configuring, self-commissioning, self-learning, self-diagnosing, self-healing, and self-transacting to enable continuous peak performance. • Lower overall building operating costs and higher asset valuation. The overarching goal is to capture 30% energy savings by enhanced management of energy consuming assets and systemsmore » through development of cost-effective sensors and controls. One step in achieving this vision is the publication of this Sensor Characteristics Reference Guide. The purpose of the guide is to inform building owners and operators of the current status, capabilities, and limitations of sensor technologies. It is hoped that this guide will aid in the design and procurement process and result in successful implementation of building sensor and control systems. DOE will also use this guide to identify research priorities, develop future specifications for potential market adoption, and provide market clarity through unbiased information« less

Uptake of an innovation in surgery: observations from the cluster-randomized Quality Initiative in Rectal Cancer trial.

PubMed

Simunovic, Marko; Coates, Angela; Smith, Andrew; Thabane, Lehana; Goldsmith, Charles H; Levine, Mark N

2013-12-01

Theory suggests the uptake of a medical innovation is influenced by how potential adopters perceive innovation characteristics and by characteristics of potential adopters. Innovation adoption is slow among the first 20% of individuals in a target group and then accelerates. The Quality Initiative in Rectal Cancer (QIRC) trial assessed if rectal cancer surgery outcomes could be improved through surgeon participation in the QIRC strategy. We tested if traditional uptake of innovation concepts applied to surgeons in the experimental arm of the trial. The QIRC strategy included workshops, access to opinion leaders, intraoperative demonstrations, postoperative questionnaires, and audit and feedback. For intraoperative demonstrations, a participating surgeon invited an outside surgeon to demonstrate optimal rectal surgery techniques. We used surgeon timing in a demonstration to differentiate early and late adopters of the QIRC strategy. Surgeons completed surveys on perceptions of the strategy and personal characteristics. Nineteen of 56 surgeons (34%) requested an operative demonstration on their first case of rectal surgery. Early and late adopters had similar perceptions of the QIRC strategy and similar characteristics. Late adopters were less likely than early adopters to perceive an advantage for the surgical techniques promoted by the trial (p = 0.023). Most traditional diffusion of innovation concepts did not apply to surgeons in the QIRC trial, with the exception of the importance of perceptions of comparative advantage.

Evaluation of plasma lactate concentration and base excess at the time of hospital admission as predictors of gastric necrosis and outcome and correlation between those variables in dogs with gastric dilatation-volvulus: 78 cases (2004-2009).

PubMed

Beer, Kari A Santoro; Syring, Rebecca S; Drobatz, Kenneth J

2013-01-01

To determine the correlation between plasma lactate concentration and base excess at the time of hospital admission and evaluate each variable as a predictor of gastric necrosis or outcome in dogs with gastric dilatation-volvulus (GDV). Retrospective case series. 78 dogs. For each dog, various data, including plasma lactate concentration and base excess at the time of hospital admission, surgical or necropsy findings, and outcome, were collected from medical records. Gastric necrosis was identified in 12 dogs at the time of surgery and in 4 dogs at necropsy. Sixty-five (83%) dogs survived to hospital discharge, whereas 13 (17%) dogs died or were euthanized. Of the 65 survivors and 8 nonsurvivors that underwent surgery, gastric necrosis was detected in 8 and 4 dogs, respectively. Via receiver operating characteristic curve analysis, an initial plasma lactate concentration cutoff of 7.4 mmol/L was 82% accurate for predicting gastric necrosis (sensitivity, 50%; specificity, 88%) and 88% accurate for predicting outcome (sensitivity, 75%; specificity, 89%). Among all dogs, the correlation between initial plasma lactate concentration and base excess was significant, although base excess was a poor discriminator for predicting gastric necrosis or outcome (area under the receiver operating characteristic curve, 0.571 and 0.565, respectively). In dogs with GDV, plasma lactate concentration at the time of hospital admission was a good predictor of gastric necrosis and outcome. However, despite the correlation between initial base excess and plasma lactate concentration, base excess should not be used for prediction of gastric necrosis or outcome in those patients.

Transportation vehicle energy intensities. A joint DOT/NASA reference paper. [energy consumption of air and ground vehicles

NASA Technical Reports Server (NTRS)

Mascy, A. C.; Paullin, R. L.

1974-01-01

A compilation of data on the energy consumption of air and ground vehicles is presented. The ratio BTU/ASM, British Thermal Units/Available Seat Mile, is used to express vehicle energy intensiveness, and related to the energy consumed directly in producing seat-mile or ton-mile productivity. Data is presented on passenger and freight vehicles which are in current use or which are about to enter service, and advanced vehicles which may be operational in the 1980's and beyond. For the advanced vehicles, an estimate is given of the date of initial operational service, and the performance characteristics. Other key considerations in interpreting energy intensiveness for a given mode are discussed, such as: load factors, operations, overhead energy consumption, and energy investments in new structure and equipment.

Solar Occultation Retrieval Algorithm Development

NASA Technical Reports Server (NTRS)

Lumpe, Jerry D.

2004-01-01

This effort addresses the comparison and validation of currently operational solar occultation retrieval algorithms, and the development of generalized algorithms for future application to multiple platforms. initial development of generalized forward model algorithms capable of simulating transmission data from of the POAM II/III and SAGE II/III instruments. Work in the 2" quarter will focus on: completion of forward model algorithms, including accurate spectral characteristics for all instruments, and comparison of simulated transmission data with actual level 1 instrument data for specific occultation events.

Status of the NOAO evaluation of the Hughes 20x64 Si:As impurity band conduction array. [for ground and space-based astronomy

NASA Technical Reports Server (NTRS)

Fowler, A. M.; Joyce, R. R.

1990-01-01

The Hughes 20 x 64 Si:As impurity band conduction arrays designed for ground-based and spaceborne astronomy observations is described together with experiments performed at NOAO to test these arrays. Special attention is given to the design and the characteristics of the test system and to the test methods. The initial tests on two columns of one array indicate that the array is easy to operate and performed satisfactorily.

14 CFR 25.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Turbine engine operating characteristics... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant General § 25.939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be investigated in...

14 CFR 25.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Turbine engine operating characteristics... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant General § 25.939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be investigated in...

14 CFR 25.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Turbine engine operating characteristics... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant General § 25.939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be investigated in...

14 CFR 25.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Turbine engine operating characteristics... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant General § 25.939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be investigated in...

14 CFR 25.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Turbine engine operating characteristics... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant General § 25.939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be investigated in...

Reliability evaluation of oil pipelines operating in aggressive environment

NASA Astrophysics Data System (ADS)

Magomedov, R. M.; Paizulaev, M. M.; Gebel, E. S.

2017-08-01

In connection with modern increased requirements for ecology and safety, the development of diagnostic services complex is obligatory and necessary enabling to ensure the reliable operation of the gas transportation infrastructure. Estimation of oil pipelines technical condition should be carried out not only to establish the current values of the equipment technological parameters in operation, but also to predict the dynamics of changes in the physical and mechanical characteristics of the material, the appearance of defects, etc. to ensure reliable and safe operation. In the paper, existing Russian and foreign methods for evaluation of the oil pipelines reliability are considered, taking into account one of the main factors leading to the appearance of crevice in the pipeline material, i.e. change the shape of its cross-section, - corrosion. Without compromising the generality of the reasoning, the assumption of uniform corrosion wear for the initial rectangular cross section has been made. As a result a formula for calculation the probability of failure-free operation was formulated. The proposed mathematical model makes it possible to predict emergency situations, as well as to determine optimal operating conditions for oil pipelines.

Waste burning and heat recovery characteristics of a mass burn incineration system.

PubMed

Chen, Wei-Hsin

2003-02-01

An experimental investigation on waste combustion characteristics of a mass burn incinerator is conducted in this study. Three different charging modes, including operator manipulation, periodic feeding, and temperature control, are taken into consideration. The results indicate that the burning characteristics in the combustion chambers are closely related to the operating modes. For the operator manipulation where the wastes are sent into the incinerator in two short periods, the entire temperature distribution of the primary combustion chamber can be partitioned into two parts, thereby yielding waste group combustion. Temperature oscillations in both the primary and secondary combustion chambers are characterized for the periodic feeding. However, because of the shorter charging period and smaller amount of waste, the burning interaction between the two chambers is initially weak and becomes notable in the final stage. When temperature control is performed, the burning oscillation of the primary combustion chamber is further amplified so the combustion interaction is drastic. These exhibitions are mainly caused by the competition between endothermic and exothermic reactions. The instantaneous heat exchange efficiency of the cyclone heat recovery system (CHRS) installed in the incineration system is also evaluated to obtain details of energy recovery behaviors. As a result, the efficiency tends to decrease linearly with increasing temperature of hot flue gas. This arises from the fact that heat loss from the gas to the environment is increased when the temperature of the former is higher, even though the temperature gradient across the cyclone is enlarged.

The Influence of Students' Pre-College Characteristics, High School Experiences, College Expectations, and Initial Enrollment Characteristics on Degree Attainment

ERIC Educational Resources Information Center

Pike, Gary R.; Hansen, Michele J.; Childress, Janice E.

2014-01-01

The present research examined the extent to which pre-college characteristics, high school experiences, college expectations, and initial enrollment characteristics were related to graduation from college. Data from admission applications, the "ACT Compass" survey, and initial enrollment measures for Fall 2004 and Fall 2005 first-time…

Analysis of Otologic Injuries Due to Blast Trauma by Handmade Explosives

PubMed Central

Aslıer, Mustafa; Aslıer, Nesibe Gül Yüksel

2017-01-01

Objective The aim of this study is to identify the otologic injuries due to handmade explosive-welded blast travma in the law enforcement officers during the combat operations in the curfew security region and to specify the disorders that Otolaryngology and Head Neck Surgery (OHNS) physicians can face during such operations. Methods Medical records of patients in law enforcement who were initially treated by OHNS physicians of Silopi State Hospital during combat operations, between December 14, 2015 and January 15, 2016 were reviewed. Twenty-five patients with otologic injuries due to blast trauma were included in the study. Trauma characteristics, physical examination findings, and beginning treatments were identified. Results Primary blast injury (PBI) was identified as the major disorder in all 24 cases. Tinnitus and hearing loss were the most frequent complaints. In physical examination, tympanic membrane perforations were found in four ears of three patients. Oral methylprednisolone in decreasing doses for 10 days was commenced as an initial treatment in patients with PBI. Secondary blast injury presented in the form of soft tissue damage in the auricular helix due to shrapnel pieces in one patient and a minor surgery was performed. Conclusion Otologic injuries due to blast trauma may often develop during this type of combat operations. Otologic symptoms should be checked, otoscopic examination should be performed, and patients should consult OHNS physicians as soon as possible after trauma. PMID:29392057

Analysis of Otologic Injuries Due to Blast Trauma by Handmade Explosives.

PubMed

Aslıer, Mustafa; Aslıer, Nesibe Gül Yüksel

2017-06-01

The aim of this study is to identify the otologic injuries due to handmade explosive-welded blast travma in the law enforcement officers during the combat operations in the curfew security region and to specify the disorders that Otolaryngology and Head Neck Surgery (OHNS) physicians can face during such operations. Medical records of patients in law enforcement who were initially treated by OHNS physicians of Silopi State Hospital during combat operations, between December 14, 2015 and January 15, 2016 were reviewed. Twenty-five patients with otologic injuries due to blast trauma were included in the study. Trauma characteristics, physical examination findings, and beginning treatments were identified. Primary blast injury (PBI) was identified as the major disorder in all 24 cases. Tinnitus and hearing loss were the most frequent complaints. In physical examination, tympanic membrane perforations were found in four ears of three patients. Oral methylprednisolone in decreasing doses for 10 days was commenced as an initial treatment in patients with PBI. Secondary blast injury presented in the form of soft tissue damage in the auricular helix due to shrapnel pieces in one patient and a minor surgery was performed. Otologic injuries due to blast trauma may often develop during this type of combat operations. Otologic symptoms should be checked, otoscopic examination should be performed, and patients should consult OHNS physicians as soon as possible after trauma.

Can demographic, clinical and treatment-related factors available at hormonal therapy initiation predict non-persistence in women with stage I-III breast cancer?

PubMed

Cahir, Caitriona; Barron, Thomas I; Sharp, Linda; Bennett, Kathleen

2017-03-01

To investigate whether demographic, clinical and treatment-related risk factors known at treatment initiation can be used to reliably predict future hormonal therapy non-persistence in women with breast cancer, and to inform intervention development. Women with stage I-III breast cancer diagnosed 2000-2012 and prescribed hormonal therapy were identified from the National Cancer Registry Ireland (NCRI) and linked to pharmacy claims data from Ireland's Primary Care Reimbursement Services (PCRS). Non-persistence was defined as a treatment gap of ≥180 days within 5 years of initiation. Seventeen demographic, clinical and treatment-related risk factors, identified from a systematic review, were abstracted from the NCRI-PCRS dataset. Multivariate binomial models were used to estimate relative risks (RR) and risk differences (RD) for associations between risk factors and non-persistence. Calibration and discriminative performance of the models were assessed. The analysis was repeated for early non-persistence (<1 year of initiation). Within 5 years of treatment initiation 680 women (19.9%) were non-persistent. Women aged <50 years (adjusted RR 1.41, 95% CI 1.16-1.70) and those prescribed antidepressants (RR 1.22, 95% CI 1.04-1.45) had increased risk of non-persistence. Married women (RR 0.82 95% CI 0.71-0.94) and those with prior medication use (RR 0.62 95% CI 0.51-0.75) had reduced risk of non-persistence. The area under the receiver-operating characteristic (ROC) curve for non-persistence was 0.61. Findings were similar for early non-persistence. The risk prediction model did not discriminate well between women at higher and lower risk of non-persistence at treatment initiation. Future studies should consider other factors, such as psychological characteristics and experience of side-effects.

A Computer-Aided Diagnosis System Using Artificial Intelligence for the Diagnosis and Characterization of Thyroid Nodules on Ultrasound: Initial Clinical Assessment.

PubMed

Choi, Young Jun; Baek, Jung Hwan; Park, Hye Sun; Shim, Woo Hyun; Kim, Tae Yong; Shong, Young Kee; Lee, Jeong Hyun

2017-04-01

An initial clinical assessment is described of a new, commercially available, computer-aided diagnosis (CAD) system using artificial intelligence (AI) for thyroid ultrasound, and its performance is evaluated in the diagnosis of malignant thyroid nodules and categorization of nodule characteristics. Patients with thyroid nodules with decisive diagnosis, whether benign or malignant, were consecutively enrolled from November 2015 to February 2016. An experienced radiologist reviewed the ultrasound image characteristics of the thyroid nodules, while another radiologist assessed the same thyroid nodules using the CAD system, providing ultrasound characteristics and a diagnosis of whether nodules were benign or malignant. The diagnostic performance and agreement of US characteristics between the experienced radiologist and the CAD system were compared. In total, 102 thyroid nodules from 89 patients were included; 59 (57.8%) were benign and 43 (42.2%) were malignant. The CAD system showed a similar sensitivity as the experienced radiologist (90.7% vs. 88.4%, p > 0.99), but a lower specificity and a lower area under the receiver operating characteristic (AUROC) curve (specificity: 74.6% vs. 94.9%, p = 0.002; AUROC: 0.83 vs. 0.92, p = 0.021). Classifications of the ultrasound characteristics (composition, orientation, echogenicity, and spongiform) between radiologist and CAD system were in substantial agreement (κ = 0.659, 0.740, 0.733, and 0.658, respectively), while the margin showed a fair agreement (κ = 0.239). The sensitivity of the CAD system using AI for malignant thyroid nodules was as good as that of the experienced radiologist, while specificity and accuracy were lower than those of the experienced radiologist. The CAD system showed an acceptable agreement with the experienced radiologist for characterization of thyroid nodules.

Hybrid Weighted Minimum Norm Method A new method based LORETA to solve EEG inverse problem.

PubMed

Song, C; Zhuang, T; Wu, Q

2005-01-01

This Paper brings forward a new method to solve EEG inverse problem. Based on following physiological characteristic of neural electrical activity source: first, the neighboring neurons are prone to active synchronously; second, the distribution of source space is sparse; third, the active intensity of the sources are high centralized, we take these prior knowledge as prerequisite condition to develop the inverse solution of EEG, and not assume other characteristic of inverse solution to realize the most commonly 3D EEG reconstruction map. The proposed algorithm takes advantage of LORETA's low resolution method which emphasizes particularly on 'localization' and FOCUSS's high resolution method which emphasizes particularly on 'separability'. The method is still under the frame of the weighted minimum norm method. The keystone is to construct a weighted matrix which takes reference from the existing smoothness operator, competition mechanism and study algorithm. The basic processing is to obtain an initial solution's estimation firstly, then construct a new estimation using the initial solution's information, repeat this process until the solutions under last two estimate processing is keeping unchanged.

Microgravity fluid management in two-phase thermal systems

NASA Technical Reports Server (NTRS)

Parish, Richard C.

1987-01-01

Initial studies have indicated that in comparison to an all liquid single phase system, a two-phase liquid/vapor thermal control system requires significantly lower pumping power, demonstrates more isothermal control characteristics, and allows greater operational flexibility in heat load placement. As a function of JSC's Work Package responsibility for thermal management of space station equipment external to the pressurized modules, prototype development programs were initiated on the Two-Phase Thermal Bus System (TBS) and the Space Erectable Radiator System (SERS). JSC currently has several programs underway to enhance the understanding of two-phase fluid flow characteristics. The objective of one of these programs (sponsored by the Microgravity Science and Applications Division at NASA-Headquarters) is to design, fabricate, and fly a two-phase flow regime mapping experiment in the Shuttle vehicle mid-deck. Another program, sponsored by OAST, involves the testing of a two-phase thermal transport loop aboard the KC-135 reduced gravity aircraft to identify system implications of pressure drop variation as a function of the flow quality and flow regime present in a representative thermal system.

Separator development and testing of nickel-hydrogen cells

NASA Technical Reports Server (NTRS)

Gonzalez-Sanabria, O. D.; Manzo, M. A.

1984-01-01

The components, design, and operating characteristics of Ni-H2 cells batteries were improved. A separator development program was designed to develop a separator that is resistant to penetration by oxygen and loose active material from then nickel electrode, while retraining the required chemical and thermal stability, reservoir capability, and high ionic conductivity. The performance of the separators in terms of cell operating voltage was to at least match that of state-of-the-art separators while eliminating the separator problems. The separators were submitted to initial screening tests and those which successfully completed the tests were built into Ni-H2 cells for short term testing. The separators with the best performance are tested for long term performance and life.

Operative team communication during simulated emergencies: Too busy to respond?

PubMed

Davis, W Austin; Jones, Seth; Crowell-Kuhnberg, Adrianna M; O'Keeffe, Dara; Boyle, Kelly M; Klainer, Suzanne B; Smink, Douglas S; Yule, Steven

2017-05-01

Ineffective communication among members of a multidisciplinary team is associated with operative error and failure to rescue. We sought to measure operative team communication in a simulated emergency using an established communication framework called "closed loop communication." We hypothesized that communication directed at a specific recipient would be more likely to elicit a check back or closed loop response and that this relationship would vary with changes in patients' clinical status. We used the closed loop communication framework to code retrospectively the communication behavior of 7 operative teams (each comprising 2 surgeons, anesthesiologists, and nurses) during response to a simulated, postanesthesia care unit "code blue." We identified call outs, check backs, and closed loop episodes and applied descriptive statistics and a mixed-effects negative binomial regression to describe characteristics of communication in individuals and in different specialties. We coded a total of 662 call outs. The frequency and type of initiation and receipt of communication events varied between clinical specialties (P < .001). Surgeons and nurses initiated fewer and received more communication events than anesthesiologists. For the average participant, directed communication increased the likelihood of check back by at least 50% (P = .021) in periods preceding acute changes in the clinical setting, and exerted no significant effect in periods after acute changes in the clinical situation. Communication patterns vary by specialty during a simulated operative emergency, and the effect of directed communication in eliciting a response depends on the clinical status of the patient. Operative training programs should emphasize the importance of quality communication in the period immediately after an acute change in the clinical setting of a patient and recognize that communication patterns and needs vary between members of multidisciplinary operative teams. Copyright © 2016 Elsevier Inc. All rights reserved.

14 CFR 27.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

14 CFR 27.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

14 CFR 27.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

14 CFR 29.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

14 CFR 29.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

14 CFR 29.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

14 CFR 29.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

14 CFR 27.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

14 CFR 27.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

14 CFR 29.939 - Turbine engine operating characteristics.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Turbine engine operating characteristics....939 Turbine engine operating characteristics. (a) Turbine engine operating characteristics must be... limitations of the rotorcraft and of the engine. (b) The turbine engine air inlet system may not, as a result...

Dressed for success? Silver impregnated nanocrystalline dressing for initial treatment of giant omphalocele.

PubMed

Percy, Dean B; Haddock, Candace; Ma, Vivian; Nowak, Amie; Panczuk, Julia; Butterworth, Sonia

2018-05-01

The purpose of this study was to describe outcomes and resource utilization in patients treated with twice-weekly silver impregnated (SI) nanocrystalline dressings for initial non-operative management of giant omphalocele (GO). A retrospective review of patients with GO treated with SI dressings was undertaken. Clinical parameters, cost, and complications were recorded. Five patients with GO were treated with SI dressings between 2014 and 2016. Clinical characteristic (mean ± SD) included gestational age 36 ± 4 weeks, birth weight 2.6 ± 0.63 kg, GO size 10.2 ± 4.7 cm, ventilator days 7.5 ± 8.7 d, days in NICU 41 ± 20 d, days to full feeds, 30 ± 15 d, and LOS 62 ± 41 d. The average in-hospital cost of SI dressings was $110 CAD/week. This is comparable to daily silver sulfadiazine dressings ($109CAD/week) which were used historically. All patients were discharged with once- or twice-weekly dressing changes. No ruptures occurred. There was one mortality secondary to pulmonary sepsis. For initial non-operative management of GO, twice weekly SI nanocrystalline dressings is safe and effective. Use of SI dressings results in decreased handling of infants, reduced physician and nursing resource utilization, and favourable outcomes. IV (Retrospective Case Series). Copyright © 2018. Published by Elsevier Inc.

42 CFR 417.930 - Initial costs of operation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 3 2010-10-01 2010-10-01 false Initial costs of operation. 417.930 Section 417.930... PREPAYMENT PLANS Administration of Outstanding Loans and Loan Guarantees § 417.930 Initial costs of operation. Under section 1305 of the PHS, loans and loan guarantees were awarded for initial costs of operation of...

MHD retrofit of steam power plants. Feasibility study. Summary and conclusions, Part I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-07-01

The US Department of Energy Division of Magnetohydrodynamics (DOE/MHD) initiated this study to evaluate the feasibility of a retrofit option to reduce the time and cost of commercializing MHD. The MHD retrofit option will integrate a nominal 260 megawatt thermal (MWt) MHD topping cycle into an existing or scheduled private utility steam plant; this facility will test both the MHD system and the combined operation of the MHD/steam plant. The 260 MWt input level was determined to be the size which could most effectively demonstrate and verify the engineering design and operational characteristics of a coal-fired, open-cycle, MHD power plant.more » Details are presented. A goal of the MHD program is to have operational by the year 2003 a commercial size, fully integrated MHD plant. This would be accomplished by demonstrating commercial scale, baseload performance of a fully integrated, MHD/steam power plant. (WHK)« less

Optimizing noise control strategy in a forging workshop.

PubMed

Razavi, Hamideh; Ramazanifar, Ehsan; Bagherzadeh, Jalal

2014-01-01

In this paper, a computer program based on a genetic algorithm is developed to find an economic solution for noise control in a forging workshop. Initially, input data, including characteristics of sound sources, human exposure, abatement techniques, and production plans are inserted into the model. Using sound pressure levels at working locations, the operators who are at higher risk are identified and picked out for the next step. The program is devised in MATLAB such that the parameters can be easily defined and changed for comparison. The final results are structured into 4 sections that specify an appropriate abatement method for each operator and machine, minimum allowance time for high-risk operators, required damping material for enclosures, and minimum total cost of these treatments. The validity of input data in addition to proper settings in the optimization model ensures the final solution is practical and economically reasonable.

Neonates and Infants Discharged Home Dependent on Medical Technology: Characteristics and Outcomes.

PubMed

Toly, Valerie Boebel; Musil, Carol M; Bieda, Amy; Barnett, Kimberly; Dowling, Donna A; Sattar, Abdus

2016-10-01

Preterm neonates and neonates with complex conditions admitted to a neonatal intensive care unit (NICU) may require medical technology (eg, supplemental oxygen, feeding tubes) for their continued survival at hospital discharge. Medical technology introduces another layer of complexity for parents, including specialized education about neonatal assessment and operation of technology. The transition home presents a challenge for parents and has been linked with greater healthcare utilization. To determine incidence, characteristics, and healthcare utilization outcomes (emergency room visits, rehospitalizations) of technology-dependent neonates and infants following initial discharge from the hospital. This descriptive, correlational study used retrospective medical record review to examine technology-dependent neonates (N = 71) upon discharge home. Study variables included demographic characteristics, hospital length of stay, and type of medical technology used. Analysis of neonates (n = 22) with 1-year postdischarge data was conducted to identify relationships with healthcare utilization. Descriptive and regression analyses were performed. Approximately 40% of the technology-dependent neonates were between 23 and 26 weeks' gestation, with birth weight of less than 1000 g. Technologies used most frequently were supplemental oxygen (66%) and feeding tubes (46.5%). The mean total hospital length of stay for technology-dependent versus nontechnology-dependent neonates was 108.6 and 25.7 days, respectively. Technology-dependent neonates who were female, with a gastrostomy tube, or with longer initial hospital length of stay were at greater risk for rehospitalization. Assessment and support of families, particularly mothers of technology-dependent neonates following initial hospital discharge, are vital. Longitudinal studies to determine factors affecting long-term outcomes of technology-dependent infants are needed.

C-reactive protein as a prognostic indicator for rebleeding in patients with nonvariceal upper gastrointestinal bleeding.

PubMed

Lee, Han Hee; Park, Jae Myung; Lee, Soon-Wook; Kang, Seung Hun; Lim, Chul-Hyun; Cho, Yu Kyung; Lee, Bo-In; Lee, In Seok; Kim, Sang Woo; Choi, Myung-Gyu

2015-05-01

In patients with acute nonvariceal upper gastrointestinal bleeding, rebleeding after an initial treatment is observed in 10-20% and is associated with mortality. To investigate whether the initial serum C-reactive protein level could predict the risk of rebleeding in patients with acute nonvariceal upper gastrointestinal bleeding. This was a retrospective study using prospectively collected data for upper gastrointestinal bleeding. Initial clinical characteristics, endoscopic features, and C-reactive protein levels were compared between those with and without 30-day rebleeding. A total of 453 patients were included (mean age, 62 years; male, 70.9%). The incidence of 30-day rebleeding was 15.9%. The mean serum C-reactive protein level was significantly higher in these patients than in those without rebleeding (P<0.001). The area under the receiver operating characteristics curve with a cutoff value of 0.5mg/dL was 0.689 (P<0.001). High serum C-reactive protein level (odds ratio, 2.98; confidence interval, 1.65-5.40) was independently associated with the 30-day rebleeding risk after adjustment for the main confounding risk factors, including age, blood pressure, and initial haemoglobin level. The serum C-reactive protein was an independent risk factor for 30-day rebleeding in patients with acute nonvariceal upper gastrointestinal bleeding, indicating a possible role as a useful screening indicator for predicting the risk of rebleeding. Copyright © 2015 Editrice Gastroenterologica Italiana S.r.l. Published by Elsevier Ltd. All rights reserved.

Power conditioning equipment for a thermoelectric outer planet spacecraft, volume 1, book 1

NASA Technical Reports Server (NTRS)

Andrews, R. E. (Editor)

1972-01-01

Equipment was designed to receive power from a radioisotope thermoelectric generator source, condition, distribute, and control this power for the spacecraft loads. The TOPS mission, aimed at a representative tour of the outer planets, would operate for an estimated 12 year period. Unique design characteristics required for the power conditioning equipment results from the long mission time and the need for autonomous on-board operations due to large communications distances and the associated time delays of ground initiated actions. The salient features of the selected power subsystem configuration are: (1) The PCE regulates the power from the radioisotope thermoelectric generator power source at 30 vdc by means of a quad-redundant shunt regulator; (2) 30 vdc power is used by certain loads, but is more generally inverted and distributed as square-wave ac power; (3) a protected bus is used to assure that power is always available to the control computer subsystem to permit corrective action to be initiated in response to fault conditions; and (4) various levels of redundancy are employed to provide high subsystem reliability.

Changing levels of quiet in an intensive care nursery.

PubMed

Philbin, M Kathleen; Gray, Lincoln

2002-09-01

To document low sound levels, the range and pattern of levels, and the relative effects of operational (staff and equipment generated) and facility (building generated) noise on the acoustic environment of a level III nursery. A quasi-experimental, prospective, longitudinal study of one bed space. Operational noise was reduced through staff behavior change while facility noise was reduced through renovation. Initial noise levels were typical of those in the literature and in recently measured nurseries. About 80% of sound levels were between 62 and 70 dBA. The lowest levels (L(min)) were 60 to 65 dBA. After staff behavior change, L(min) was about 56 dBA although the highest levels (L(max)) remained at 78 to 100 dBA. Levels following renovation were reduced to L(min)s of 47 to 51 dBA and L(max)s of 68 to 84 dBA, perceived as three or four times quieter than initially. Staff behavior as well as the acoustical characteristics of the facility determine the levels of noise and quiet in an intensive care nursery.

49 CFR 234.205 - Operating characteristics of warning system apparatus.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Operating characteristics of warning system... Maintenance Standards § 234.205 Operating characteristics of warning system apparatus. Operating... system shall be maintained in accordance with the limits within which the system is designed to operate. ...

49 CFR 234.205 - Operating characteristics of warning system apparatus.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Operating characteristics of warning system... Maintenance Standards § 234.205 Operating characteristics of warning system apparatus. Operating... system shall be maintained in accordance with the limits within which the system is designed to operate. ...

49 CFR 234.205 - Operating characteristics of warning system apparatus.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Operating characteristics of warning system... Maintenance Standards § 234.205 Operating characteristics of warning system apparatus. Operating... system shall be maintained in accordance with the limits within which the system is designed to operate. ...

Diagnostics and control of wavenumber stability and purity of tunable diode lasers relevant to their use as local oscillators in heterodyne systems

NASA Technical Reports Server (NTRS)

Poultney, S.; Chen, D.; Steinberg, G.; Wu, F.; Pires, A.; Miller, M. D.; Mcnally, M.

1980-01-01

Initial operation of the tunable diode lasers (TDL) showed that it was not possible to adjust the wavenumber to one selected a priori in the TDL tuning range. During operation, the operating point would change by 0.1/cm over the longer term with even larger changes occurring during some thermal cycles. Most changes during thermal cycling required using lower temperatures and higher currents to reach the former wavenumber (when it could be reached). In many cases, an operating point could be selected by changing TDL current and temperature to give both the desired wavenumber and most of the power in a single mode. The selection procedure had to be used after each thermal cycling. Wavenumber nonlinearities of about 10% over a 0.5 cm tuning range were observed. Diagnostics of the single mode selected by a grating monochromator showed wavenumber fine structure under certain operating conditions. The characteristics due to the TDL environment included short term wavenumber stability, the instrument lineshape function, and intermediate term wavenumber stability.

33 CFR 157.158 - COW operations: Changed characteristics.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false COW operations: Changed... CARRYING OIL IN BULK Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.158 COW operations: Changed characteristics. The COW system may be operated with characteristics that do not meet those...

An Approach to Economic Dispatch with Multiple Fuels Based on Particle Swarm Optimization

NASA Astrophysics Data System (ADS)

Sriyanyong, Pichet

2011-06-01

Particle Swarm Optimization (PSO), a stochastic optimization technique, shows superiority to other evolutionary computation techniques in terms of less computation time, easy implementation with high quality solution, stable convergence characteristic and independent from initialization. For this reason, this paper proposes the application of PSO to the Economic Dispatch (ED) problem, which occurs in the operational planning of power systems. In this study, ED problem can be categorized according to the different characteristics of its cost function that are ED problem with smooth cost function and ED problem with multiple fuels. Taking the multiple fuels into account will make the problem more realistic. The experimental results show that the proposed PSO algorithm is more efficient than previous approaches under consideration as well as highly promising in real world applications.

Influence of Off-Centre Operation on the Performance of HTS Maglev

NASA Astrophysics Data System (ADS)

Gou, Y.; He, D.; Zheng, J.; Ye, C.; Xu, Y.; Sun, R.; Che, T.; Deng, Z.

2014-03-01

Owing to instinctive self-stable levitation characteristics, high-temperature superconducting (HTS) maglev using bulk high-temperature superconductors attracts more and more attention from scientists and engineers around the world. In this paper, the levitation force relaxation and guidance force characteristics of a Y-Ba-Cu-O levitation unit with different eccentric distances (EDs) off the center of the permanent magnet guideway were experimentally investigated under field-cooling (FC) conditions. Experimental results indicate that the levitation force slightly increases at small EDs firstly, but degrades with further increasing of EDs. However, the maximum guidance force and its stiffness exhibit enhancement in moderate ED range. The results demonstrate that a properly designed initial FC eccentric distance is important for the practical applications of HTS maglev according to specific requirements like running in curve lines.

Radio broadcasting via satellite

NASA Astrophysics Data System (ADS)

Helm, Neil R.; Pritchard, Wilbur L.

1990-10-01

Market areas offering potential for future narrowband broadcast satellites are examined, including international public diplomacy, government- and advertising-supported, and business-application usages. Technical issues such as frequency allocation, spacecraft types, transmission parameters, and radio receiver characteristics are outlined. Service and system requirements, advertising revenue, and business communications services are among the economic issues discussed. The institutional framework required to provide an operational radio broadcast service is studied, and new initiatives in direct broadcast audio radio systems, encompassing studies, tests, in-orbit demonstrations of, and proposals for national and international commercial broadcast services are considered.

Rotorcraft flight-propulsion control integration

NASA Technical Reports Server (NTRS)

Mihaloew, James R.; Ballin, Mark G.; Ruttledge, D. G. C.

1988-01-01

The NASA Ames and Lewis Research Centers, in conjunction with the Army Research and Technology Laboratories have initiated and completed, in part, a joint research program focused on improving the performance, maneuverability, and operating characteristics of rotorcraft by integrating the flight and propulsion controls. The background of the program, its supporting programs, its goals and objectives, and an approach to accomplish them are discussed. Results of the modern control governor design of the T700 and the Rotorcraft Integrated Flight-Propulsion Control Study, which were key elements of the program, are also presented.

Low power consumption resistance random access memory with Pt/InOx/TiN structure

NASA Astrophysics Data System (ADS)

Yang, Jyun-Bao; Chang, Ting-Chang; Huang, Jheng-Jie; Chen, Yu-Ting; Tseng, Hsueh-Chih; Chu, Ann-Kuo; Sze, Simon M.; Tsai, Ming-Jinn

2013-09-01

In this study, the resistance switching characteristics of a resistive random access memory device with Pt/InOx/TiN structure is investigated. Unstable bipolar switching behavior is observed during the initial switching cycle, which then stabilizes after several switching cycles. Analyses indicate that the current conduction mechanism in the resistance state is dominated by Ohmic conduction. The decrease in electrical conductance can be attributed to the reduction of the cross-sectional area of the conduction path. Furthermore, the device exhibits low operation voltage and power consumption.

Qualitative investigation of booster recovery in open sea

NASA Technical Reports Server (NTRS)

Beck, P. E.

1973-01-01

Limited tests were conducted using 1/27 scale model of a Titan 3C booster plus 1/32.9 and 1/15.6 scale models of a solid rocket booster case to establish some of the characteristics that will effect recovery operations in open seas. This preliminary effort was designed to provide additional background information for conceptual development of a waterborne recovery system for space shuttle boosters, pending initiation of comprehensive studies. The models were not instrumented; therefore, all data are qualitative (approximations) and are based on observations plus photographic coverage.

[Design on tester of pull-out force for orthodontic micro implant].

PubMed

Su, He; Wu, Pei; Wang, Huiyuan; Chen, Yan; Bao, Xuemei

2013-09-01

A special device for measuring the pull-out force of orthodontic micro implant was designed, which has the characteristics of simple construction and easy operation, and can be used to detect the pull-out-force of orthodontic micro implant. The tested data was stored and analyzed by a computer, and as the results, the pull-out-force curve, maximum pull-out force as well as average pull-out force were outputted, which was applied in analyzing or investigating the initial stability and immediate loading property of orthodontic micro implant.

Acquisition of Ice Thickness and Ice Surface Characteristics In the Seasonal Ice Zone by CULPIS-X During the US Coast Guards Arctic Domain Awareness Program

DTIC Science & Technology

2015-09-30

as a package called CULPIS [Crocker et al., 2012 ]. The CULPIS-X instruments are designed to acquire: • Distance to surface measured at 400...Control Board (ACCB) request was re-initiated in early 2015 with the USCG ALC by our POC in Kodiak, AK, LT. William Coombs . The CFD and FED data were...X Assembly manual and an Operations Manual for use by the USCG. These documents were requested by our USCG Kodiak contact, LT. William Coombs

Chronology of KSC and KSC Related Events for 1976

NASA Technical Reports Server (NTRS)

1977-01-01

Much of the activity at the Kennedy Space Center in 1976, particularly during the first 9 months, centered on the planning, construction, maintenance,and operation of the U.S. Bicentennial Exposition on Science and Technology. Since this project began in 1975, the historian has included some dates of key events relating to the Exposition to introduce the 1976 Chronology. Also in 1975 A 3-year program was initiated at KSC to research the electrical characteristics of thunderstorms. This is an international program involving top atmospheric researchers of the free world.

LANDSAT-4 TM image data quality analysis for energy-related applications

NASA Technical Reports Server (NTRS)

Wukelic, G. E.; Foote, H. P.

1983-01-01

LANDSAT-4 Thematic Mapper (TM) data performance and utility characteristics from an energy research and technology perspective is evaluated. The program focuses on evaluating applicational implications of using such data, in combination with other digital data, for current and future energy research and technology activities. Prime interest is in using TM data for siting, developing and operating federal energy facilities. Secondary interests involve the use of such data for resource exploration, environmental monitoring and basic scientific initiatives such as in support of the Continental Scientific Drilling Program.

Second consultant opinion for elective orthopedic surgery.

PubMed Central

McCarthy, E G; Finkel, M L

1981-01-01

We abstracted records of 369 patients whose recommendations for elective orthopedic surgery were not confirmed by a second opinion consultant. Six months or more after the initial recommendation for surgery, 82 per cent had not had the operation performed, irrespective of the diagnosis and the characteristics of the physician recommending surgery. Reasons for consultant non-confirmation included: use of a cast, brace, or corrective footwear preferable (26.3 per cent), symptoms not severe enough (18.4 per cent), and physical therapy/exercises preferable (17.8 per cent). PMID:7294266

Arc driver operation for either efficient energy transfer or high-current generator

NASA Technical Reports Server (NTRS)

Dannenberg, R. E.; Silva, A. F.

1972-01-01

An investigation is made to establish predictable electric arcs along triggered paths for research purposes, the intended application being the heating of the driver gas of a 1 MJ electrically driven shock tube. Trigger conductors consisting of wires, open tubes, and tubes pressurized with different gases were investigated either on the axis of the arc chamber or spiraled along the chamber walls. Design criteria are presented for successful arc initiation with reproducible voltage-current characteristics. Results are compared with other facilities and several application areas are discussed.

Initial 12-h operative fluid volume is an independent risk factor for pleural effusion after hepatectomy.

PubMed

Cheng, Xiang; Wu, Jia-Wei; Sun, Ping; Song, Zi-Fang; Zheng, Qi-Chang

2016-12-01

Pleural effusion after hepatectomy is associated with significant morbidity and prolonged hospital stays. Several studies have addressed the risk factors for postoperative pleural effusion. However, there are no researches concerning the role of the initial 12-h operative fluid volume. The aim of this study was to evaluate whether the initial 12-h operative fluid volume during liver resection is an independent risk factor for pleural effusion after hepatectomy. In this study, we retrospectively analyzed clinical data of 470 patients consecutively undergoing elective hepatectomy between January 2011 and December 2012. We prospectively collected and retrospectively analyzed baseline and clinical data, including preoperative, intraoperative, and postoperative variables. Univariate and multivariate analyses were carried out to identify whether the initial 12-h operative fluid volume was an independent risk factor for pleural effusion after hepatectomy. The multivariate analysis identified 2 independent risk factors for pleural effusion: operative time [odds ratio (OR)=10.2] and initial 12-h operative fluid volume (OR=1.0003). Threshold effect analyses revealed that the initial 12 h operative fluid volume was positively correlated with the incidence of pleural effusion when the initial 12-h operative fluid volume exceeded 4636 mL. We conclude that the initial 12-h operative fluid volume during liver resection and operative time are independent risk factors for pleural effusion after hepatectomy. Perioperative intravenous fluids should be restricted properly.

Automatic joint alignment measurements in pre- and post-operative long leg standing radiographs.

PubMed

Goossen, A; Weber, G M; Dries, S P M

2012-01-01

For diagnosis or treatment assessment of knee joint osteoarthritis it is required to measure bone morphometry from radiographic images. We propose a method for automatic measurement of joint alignment from pre-operative as well as post-operative radiographs. In a two step approach we first detect and segment any implants or other artificial objects within the image. We exploit physical characteristics and avoid prior shape information to cope with the vast amount of implant types. Subsequently, we exploit the implant delineations to adapt the initialization and adaptation phase of a dedicated bone segmentation scheme using deformable template models. Implant and bone contours are fused to derive the final joint segmentation and thus the alignment measurements. We evaluated our method on clinical long leg radiographs and compared both the initialization rate, corresponding to the number of images successfully processed by the proposed algorithm, and the accuracy of the alignment measurement. Ground truth has been generated by an experienced orthopedic surgeon. For comparison a second reader reevaluated the measurements. Experiments on two sets of 70 and 120 digital radiographs show that 92% of the joints could be processed automatically and the derived measurements of the automatic method are comparable to a human reader for pre-operative as well as post-operative images with a typical error of 0.7° and correlations of r = 0.82 to r = 0.99 with the ground truth. The proposed method allows deriving objective measures of joint alignment from clinical radiographs. Its accuracy and precision are on par with a human reader for all evaluated measurements.

Whole-Home Dehumidifiers: Field-Monitoring Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burke, Tom; Willem, Henry; Ni, Chun Chun

2014-09-23

Lawrence Berkeley National Laboratory (LBNL) initiated a WHD field-metering study to expand current knowledge of and obtain data on WHD operation and energy consumption in real-world applications. The field study collected real-time data on WHD energy consumption, along with information regarding housing characteristics, consumer behavior, and various outdoor conditions expected to affect WHD performance and efficiency. Although the metering study collected similar data regarding air conditioner operation, this report discusses only WHDs. The primary objectives of the LBNL field-metering study are to (1) expand knowledge of the configurations, energy consumption profiles, consumer patterns of use (e.g., relative humidity [RH] settings),more » and environmental parameters of whole-home dehumidification systems; and (2) develop distributions of hours of dehumidifier operation in four operating modes: off, standby, fan-only, and compressor (also called dehumidification mode). Profiling energy consumption entails documenting the power consumption, duration of power consumption in different modes, condensate generation, and properties of output air of an installed system under field conditions of varying inlet air temperature and RH, as well as system configuration. This profiling provides a more detailed and deeper understanding of WHD operation and its complexities. This report describes LBNL’s whole-home dehumidification field-metering study conducted at four homes in Wisconsin and Florida. The initial phase of the WHD field-metering study was conducted on one home in Madison, Wisconsin, from June to December of 2013. During a second phase, three Florida homes were metered from June to October of 2014. This report presents and examines data from the Wisconsin site and from the three Florida sites.« less

Methodological approaches to conducting pilot and proof tests on reverse-osmosis systems: Results of comparative studies

NASA Astrophysics Data System (ADS)

Panteleev, A. A.; Bobinkin, V. V.; Larionov, S. Yu.; Ryabchikov, B. E.; Smirnov, V. B.; Shapovalov, D. A.

2017-10-01

When designing large-scale water-treatment plants based on reverse-osmosis systems, it is proposed to conduct experimental-industrial or pilot tests for validated simulation of the operation of the equipment. It is shown that such tests allow establishing efficient operating conditions and characteristics of the plant under design. It is proposed to conduct pilot tests of the reverse-osmosis systems on pilot membrane plants (PMPs) and test membrane plants (TMPs). The results of a comparative experimental study of pilot and test membrane plants are exemplified by simulating the operating parameters of the membrane elements of an industrial plant. It is concluded that the reliability of the data obtained on the TMP may not be sufficient to design industrial water-treatment plants, while the PMPs are capable of providing reliable data that can be used for full-scale simulation of the operation of industrial reverse-osmosis systems. The test membrane plants allow simulation of the operating conditions of individual industrial plant systems; therefore, potential areas of their application are shown. A method for numerical calculation and experimental determination of the true selectivity and the salt passage are proposed. An expression has been derived that describes the functional dependence between the observed and true salt passage. The results of the experiments conducted on a test membrane plant to determine the true value of the salt passage of a reverse-osmosis membrane are exemplified by magnesium sulfate solution at different initial operating parameters. It is shown that the initial content of a particular solution component has a significant effect on the change in the true salt passage of the membrane.

Driving style recognition method using braking characteristics based on hidden Markov model

PubMed Central

Wu, Chaozhong; Lyu, Nengchao; Huang, Zhen

2017-01-01

Since the advantage of hidden Markov model in dealing with time series data and for the sake of identifying driving style, three driving style (aggressive, moderate and mild) are modeled reasonably through hidden Markov model based on driver braking characteristics to achieve efficient driving style. Firstly, braking impulse and the maximum braking unit area of vacuum booster within a certain time are collected from braking operation, and then general braking and emergency braking characteristics are extracted to code the braking characteristics. Secondly, the braking behavior observation sequence is used to describe the initial parameters of hidden Markov model, and the generation of the hidden Markov model for differentiating and an observation sequence which is trained and judged by the driving style is introduced. Thirdly, the maximum likelihood logarithm could be implied from the observable parameters. The recognition accuracy of algorithm is verified through experiments and two common pattern recognition algorithms. The results showed that the driving style discrimination based on hidden Markov model algorithm could realize effective discriminant of driving style. PMID:28837580

40 CFR 63.2862 - What records must I keep?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) initial startup period or the § 63.2850(e)(2) malfunction period. Complete both plans before the... such as normal operation, nonoperating, initial startup period, malfunction period, or exempt operation... inventory. (ii) The operating status of your source such as normal operation, nonoperating, initial startup...

40 CFR 63.2862 - What records must I keep?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) initial startup period or the § 63.2850(e)(2) malfunction period. Complete both plans before the... such as normal operation, nonoperating, initial startup period, malfunction period, or exempt operation... inventory. (ii) The operating status of your source such as normal operation, nonoperating, initial startup...

40 CFR 63.2862 - What records must I keep?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) initial startup period or the § 63.2850(e)(2) malfunction period. Complete both plans before the... such as normal operation, nonoperating, initial startup period, malfunction period, or exempt operation... inventory. (ii) The operating status of your source such as normal operation, nonoperating, initial startup...

40 CFR 63.2862 - What records must I keep?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) initial startup period or the § 63.2850(e)(2) malfunction period. Complete both plans before the... such as normal operation, nonoperating, initial startup period, malfunction period, or exempt operation... inventory. (ii) The operating status of your source such as normal operation, nonoperating, initial startup...

40 CFR 63.2862 - What records must I keep?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) initial startup period or the § 63.2850(e)(2) malfunction period. Complete both plans before the... such as normal operation, nonoperating, initial startup period, malfunction period, or exempt operation... inventory. (ii) The operating status of your source such as normal operation, nonoperating, initial startup...

Early Experience of Robotic Hysterectomy for Treatment of Benign Uterine Disease.

PubMed

Gutierrez, Ana Luiza; Binda, Márcia Luisa Montalvão Appel; Ramos, José Geraldo Lopes

2016-09-01

Objectives  To demonstrate the initial experience of robotic hysterectomy to treat benign uterine disease at a university hospital in Brazil. Methods  A cross-sectional study was conducted to review data from the first twenty patients undergoing robotic hysterectomy at our hospital. The surgeries were performed from November 2013 to August 2014, all of them by the same surgeon. The patients were reviewed for preoperative characteristics, including age, body mass index (BMI), indications for the hysterectomy and previous surgeries. Data of operative times, complications, postoperative pain and length of hospital stay were also collected. Results  The total operating room time was 252.9 minutes, while the operative time was 180.7 minutes and the console time was 136.6 minutes. Docking time was 4.2 minutes, and the average undocking time was 1.9 minutes. There was a strong correlation between the operative time and the patient's BMI ( r  = 0.670; p  = 0.001). The console time had significant correlation with the uterine weight and the patient's BMI ( r  = 0.468; p  = 0.037). A learning curve was observed during docking and undocking times. Conclusion  Despite its high cost, the robotic surgery is gaining more space in gynecological surgery. By the results obtained in our hospital, this surgical proposal proved to be feasible and safe. Our initial experience demonstrated a learning curve in some ways. Thieme Publicações Ltda Rio de Janeiro, Brazil.

Electron spin resonance observation of charge carrier concentration in organic field-effect transistors during device operation

NASA Astrophysics Data System (ADS)

Tanaka, Hisaaki; Hirate, Masataka; Watanabe, Shun-ichiro; Kaneko, Kazuaki; Marumoto, Kazuhiro; Takenobu, Taishi; Iwasa, Yoshihiro; Kuroda, Shin-ichi

2013-01-01

Charge carrier concentration in operating organic field-effect transistors (OFETs) reflects the electric potential within the channel, acting as a key quantity to clarify the operation mechanism of the device. Here, we demonstrate a direct determination of charge carrier concentration in the operating devices of pentacene and poly(3-hexylthiophene) (P3HT) by field-induced electron spin resonance (FI-ESR) spectroscopy. This method sensitively detects polarons induced by applying gate voltage, giving a clear FI-ESR signal around g=2.003 in both devices. Upon applying drain-source voltage, carrier concentration decreases monotonically in the FET linear region, reaching about 70% of the initial value at the pinch-off point, and stayed constant in the saturation region. The observed results are reproduced well from the theoretical potential profile based on the gradual channel model. In particular, the carrier concentration at the pinch-off point is calculated to be β/(β+1) of the initial value, where β is the power exponent in the gate voltage (Vgs) dependence of the mobility (μ), expressed as μ∝Vgsβ-2, providing detailed information of charge transport. The present devices show β=2.6 for the pentacene and β=2.3 for the P3HT cases, consistent with those determined by transfer characteristics. The gate voltage dependence of the mobility, originating from the charge trapping at the device interface, is confirmed microscopically by the motional narrowing of the FI-ESR spectra.

Head-mounted display systems and the special operations soldier

NASA Astrophysics Data System (ADS)

Loyd, Rodney B.

1998-08-01

In 1997, the Boeing Company, working with DARPA under the Smart Modules program and the US Army Soldier Systems Command, embarked on an advanced research and development program to develop a wearable computer system tailored for use with soldiers of the US Special Operations Command. The 'special operations combat management system' is a rugged advanced wearable tactical computer, designed to provide the special operations soldier with enhanced situation awareness and battlefield information capabilities. Many issues must be considered during the design of wearable computers for a combat soldier, including the system weight, placement on the body with respect to other equipment, user interfaces and display system characteristics. During the initial feasibility study for the system, the operational environment was examined and potential users were interviewed to establish the proper display solution for the system. Many display system requirements resulted, such as head or helmet mounting, Night Vision Goggle compatibility, minimal visible light emissions, environmental performance and even the need for handheld or other 'off the head' type display systems. This paper will address these issues and other end user requirements for display systems for applications in the harsh and demanding environment of the Special Operations soldier.

Efficacy of Single-dose and 2-dose Intravenous Administration of Ramosetron in Preventing Postoperative Nausea and Vomiting After Laparoscopic Gynecologic Operation: A Randomized, Double-blind, Placebo-controlled, Phase 2 Trial.

PubMed

Lee, Banghyun; Kim, Kidong; Suh, Dong Hoon; Shin, Hyun-Jung; No, Jae Hong; Lee, Jung Ryeol; Jee, Byung Chul; Hwang, Jung Won; Do, Sang Hwan; Kim, Yong Beom

2017-06-01

This randomized trial investigated whether a 2-dose administration of intravenous ramosetron (5-hydroxytryptamine type 3 receptor antagonist) is more effective than a single-dose administration in preventing postoperative nausea and vomiting (PONV) in 89 patients who were scheduled to undergo laparoscopic operation for benign gynecologic diseases and to receive intravenous patient-controlled analgesia for relief of postoperative pain. After assignment at a ratio of 1:1, intravenous ramosetron (0.3 mg) was initially administered at the end of skin closure in all patients. Thereafter, ramosetron (0.3 mg) and placebo were administered to the study and control groups, respectively, at 4 hours after the operation. The baseline and operative characteristics were similar between the groups. The incidence of PONV during the 24-hour period after operation which was assessed as the primary endpoint did not differ between the groups. No serious adverse events occurred in either group. A 2-dose administration of intravenous ramosetron may not be superior to a single-dose administration in preventing PONV in patients undergoing laparoscopic operation for benign gynecologic diseases.

Meteorological factors and timing of the initiating event of human parturition

NASA Astrophysics Data System (ADS)

Hirsch, Emmet; Lim, Courtney; Dobrez, Deborah; Adams, Marci G.; Noble, William

2011-03-01

The aim of this study was to determine whether meteorological factors are associated with the timing of either onset of labor with intact membranes or rupture of membranes prior to labor—together referred to as `the initiating event' of parturition. All patients delivering at Evanston Hospital after spontaneous labor or rupture of membranes at ≥20 weeks of gestation over a 6-month period were studied. Logistic regression models of the initiating event of parturition using clinical variables (maternal age, gestational age, parity, multiple gestation and intrauterine infection) with and without the addition of meteorological variables (barometric pressure, temperature and humidity) were compared. A total of 1,088 patients met the inclusion criteria. Gestational age, multiple gestation and chorioamnionitis were associated with timing of initiation of parturition ( P < 0.01). The addition of meteorological to clinical variables generated a statistically significant improvement in prediction of the initiating event; however, the magnitude of this improvement was small (less than 2% difference in receiver-operating characteristic score). These observations held regardless of parity, fetal number and gestational age. Meteorological factors are associated with the timing of parturition, but the magnitude of this association is small.

Narrow field electromagnetic sensor system and method

DOEpatents

McEwan, Thomas E.

1996-01-01

A narrow field electromagnetic sensor system and method of sensing a characteristic of an object provide the capability to realize a characteristic of an object such as density, thickness, or presence, for any desired coordinate position on the object. One application is imaging. The sensor can also be used as an obstruction detector or an electronic trip wire with a narrow field without the disadvantages of impaired performance when exposed to dirt, snow, rain, or sunlight. The sensor employs a transmitter for transmitting a sequence of electromagnetic signals in response to a transmit timing signal, a receiver for sampling only the initial direct RF path of the electromagnetic signal while excluding all other electromagnetic signals in response to a receive timing signal, and a signal processor for processing the sampled direct RF path electromagnetic signal and providing an indication of the characteristic of an object. Usually, the electromagnetic signal is a short RF burst and the obstruction must provide a substantially complete eclipse of the direct RF path. By employing time-of-flight techniques, a timing circuit controls the receiver to sample only the initial direct RF path of the electromagnetic signal while not sampling indirect path electromagnetic signals. The sensor system also incorporates circuitry for ultra-wideband spread spectrum operation that reduces interference to and from other RF services while allowing co-location of multiple electronic sensors without the need for frequency assignments.

Narrow field electromagnetic sensor system and method

DOEpatents

McEwan, T.E.

1996-11-19

A narrow field electromagnetic sensor system and method of sensing a characteristic of an object provide the capability to realize a characteristic of an object such as density, thickness, or presence, for any desired coordinate position on the object. One application is imaging. The sensor can also be used as an obstruction detector or an electronic trip wire with a narrow field without the disadvantages of impaired performance when exposed to dirt, snow, rain, or sunlight. The sensor employs a transmitter for transmitting a sequence of electromagnetic signals in response to a transmit timing signal, a receiver for sampling only the initial direct RF path of the electromagnetic signal while excluding all other electromagnetic signals in response to a receive timing signal, and a signal processor for processing the sampled direct RF path electromagnetic signal and providing an indication of the characteristic of an object. Usually, the electromagnetic signal is a short RF burst and the obstruction must provide a substantially complete eclipse of the direct RF path. By employing time-of-flight techniques, a timing circuit controls the receiver to sample only the initial direct RF path of the electromagnetic signal while not sampling indirect path electromagnetic signals. The sensor system also incorporates circuitry for ultra-wideband spread spectrum operation that reduces interference to and from other RF services while allowing co-location of multiple electronic sensors without the need for frequency assignments. 12 figs.

Combining functional and tubular damage biomarkers improves diagnostic precision for acute kidney injury after cardiac surgery.

PubMed

Basu, Rajit K; Wong, Hector R; Krawczeski, Catherine D; Wheeler, Derek S; Manning, Peter B; Chawla, Lakhmir S; Devarajan, Prasad; Goldstein, Stuart L

2014-12-30

Increases in serum creatinine (ΔSCr) from baseline signify acute kidney injury (AKI) but offer little granular information regarding its characteristics. The 10th Consensus Conference of the Acute Dialysis Quality Initiative (ADQI) suggested that combining AKI biomarkers would provide better precision for AKI course prognostication. This study investigated the value of combining a functional damage biomarker (plasma cystatin C [pCysC]) with a tubular damage biomarker (urine neutrophil gelatinase-associated lipocalin [uNGAL]), forming a composite biomarker for prediction of discrete characteristics of AKI. Data from 345 children after cardiopulmonary bypass (CPB) were analyzed. Severe AKI was defined as Kidney Disease Global Outcomes Initiative stages 2 to 3 (≥100% ΔSCr) within 7 days of CPB. Persistent AKI lasted >2 days. SCr in reversible AKI returned to baseline ≤48 h after CPB. The composite of uNGAL (>200 ng/mg urine Cr = positive [+]) and pCysC (>0.8 mg/l = positive [+]), uNGAL+/pCysC+, measured 2 h after CPB initiation, was compared to ΔSCr increases of ≥50% for correlation with AKI characteristics by using predictive probabilities, likelihood ratios (LR), and area under the curve receiver operating curve (AUC-ROC) values [Corrected]. Severe AKI occurred in 18% of patients. The composite uNGAL+/pCysC+ demonstrated a greater likelihood than ΔSCr for severe AKI (+LR: 34.2 [13.0:94.0] vs. 3.8 [1.9:7.2]) and persistent AKI (+LR: 15.6 [8.8:27.5] versus 4.5 [2.3:8.8]). In AKI patients, the uNGAL-/pCysC+ composite was superior to ΔSCr for prediction of transient AKI. Biomarker composites carried greater probability for specific outcomes than ΔSCr strata. Composites of functional and tubular damage biomarkers are superior to ΔSCr for predicting discrete characteristics of AKI. Copyright © 2014 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

Combining Functional and Tubular Damage Biomarkers Improves Diagnostic Precision for Acute Kidney Injury After Cardiac Surgery

PubMed Central

Basu, Rajit K.; Wong, Hector R.; Krawczeski, Catherine D.; Wheeler, Derek S.; Manning, Peter B.; Chawla, Lakhmir S.; Devarajan, Prasad; Goldstein, Stuart L.

2015-01-01

BACKGROUND Increases in serum creatinine (ΔSCr) from baseline signify acute kidney injury (AKI) but offer little granular information regarding its characteristics. The 10th Consensus Conference of the Acute Dialysis Quality Initiative (ADQI) suggested that combining AKI biomarkers would provide better precision for AKI course prognostication. OBJECTIVES This study investigated the value of combining a functional damage biomarker (plasma cystatin C [pCysC]) with a tubular damage biomarker (urine neutrophil gelatinase-associated lipocalin [uNGAL]), forming a composite biomarker for prediction of discrete characteristics of AKI. METHODS Data from 345 children after cardiopulmonary bypass (CPB) were analyzed. Severe AKI was defined as Kidney Disease Global Outcomes Initiative stages 2 to 3 (>100% ΔSCr) within 7 days of CPB. Persistent AKI lasted >2 days. SCr in reversible AKI returned to baseline ≤48 h after CPB. The composite of uNGAL (>200 ng/mg urine Cr = positive [+]) and pCysC (>0.8 mg/l = positive [+]), uNGAL+/pCysC+, measured 2 h after CPB initiation, was compared to ΔSCr increases of ≤50% for correlation with AKI characteristics by using predictive probabilities, likelihood ratios (LR), and area under the curve receiver operating curve (AUC-ROC) values. RESULTS Severe AKI occurred in 18% of patients. The composite uNGAL+/pCysC+ demonstrated a greater likelihood than ΔSCr for severe AKI (+LR: 34.2 [13.0:94.0] vs. 3.8 [1.9:7.2]) and persistent AKI (+LR: 15.6 [8.8:27.5] versus 4.5 [2.3:8.8]). In AKI patients, the uNGAL−/pCysC+ composite was superior to ΔSCr for prediction of transient AKI. Biomarker composites carried greater probability for specific outcomes than ΔSCr strata. CONCLUSIONS Composites of functional and tubular damage biomarkers are superior to ΔSCr for predicting discrete characteristics of AKI. PMID:25541128

Metformin: A Review of Characteristics, Properties, Analytical Methods and Impact in the Green Chemistry.

PubMed

da Trindade, Mariana Teixeira; Kogawa, Ana Carolina; Salgado, Hérida Regina Nunes

2018-01-02

Diabetes mellitus (DM) is considered a public health problem. The initial treatment consists of improving the lifestyle and making changes in the diet. When these changes are not enough, the use of medication becomes necessary. The metformin aims to reduce the hepatic production of glucose and is the preferred treatment for type 2. The objective is to survey the characteristics and properties of metformin, as well as hold a discussion on the existing analytical methods to green chemistry and their impacts for both the operator and the environment. For the survey, data searches were conducted by scientific papers in the literature as well as in official compendium. The characteristics and properties are shown, also, methods using liquid chromatography techniques, titration, absorption spectrophotometry in the ultraviolet and the infrared region. Most of the methods presented are not green chemistry oriented. It is necessary the awareness of everyone involved in the optimization of the methods applied through the implementation of green chemistry to determine the metformin.

Long-Life, Lightweight, Multi-Roller Traction Drives for Planetary Vehicle Surface Exploration

NASA Technical Reports Server (NTRS)

Klein, Richard C.; Fusaro, Robert L.; Dimofte, Florin

2012-01-01

NASA s initiative for Lunar and Martian exploration will require long lived, robust drive systems for manned vehicles that must operate in hostile environments. The operation of these mechanical drives will pose a problem because of the existing extreme operating conditions. Some of these extreme conditions include operating at a very high or very cold temperature, operating over a wide range of temperatures, operating in very dusty environments, operating in a very high radiation environment, and operating in possibly corrosive environments. Current drive systems use gears with various configurations of teeth. These gears must be lubricated with oil (or grease) and must have some sort of a lubricant resupply system. For drive systems, oil poses problems such as evaporation, becoming too viscous and eventually freezing at cold temperatures, being too thin to lubricate at high temperatures, being degraded by the radiation environment, being contaminated by the regolith (soil), and if vaporized (and not sealed), it will contaminate the regolith. Thus, it may not be advisable or even possible to use oil because of these limitations. An oil-less, compact traction vehicle drive is a drive designed for use in hostile environments like those that will be encountered on planetary surfaces. Initially, traction roller tests in vacuum were conducted to obtain traction and endurance data needed for designing the drives. From that data, a traction drive was designed that would fit into a prototype lunar rover vehicle, and this design data was used to construct several traction drives. These drives were then tested in air to determine their performance characteristics, and if any final corrections to the designs were necessary. A limitation with current speed reducer systems such as planetary gears and harmonic drives is the high-contact stresses that occur at tooth engagement and in the harmonic drive wave generator interface. These high stresses induce high wear of solid lubricant coatings, thus necessitating the use of liquid lubricants for long life.

Initial Characteristics and Mentoring Satisfaction of College Women Mentoring Youth: Implications for Training

ERIC Educational Resources Information Center

Foukal, Martha D.; Lawrence, Edith C.; Williams, Joanna L.

2016-01-01

Being a youth mentor is popular among college students, yet little is known about how their initial characteristics are related to mentoring satisfaction. Survey data from college women enrolled in a youth mentoring program (n = 158) and a comparison group (n = 136) were analyzed to determine how initial characteristics of youth mentors (a) differ…

14 CFR 91.867 - Phased compliance for new entrants.

Code of Federal Regulations, 2010 CFR

2010-01-01

... initiating operations under part 121 of this chapter on or before December 31, 1994, may initiate service... initiating part 129 operations on or before December 31, 1994, may initiate service without regard to the... the fleet on U.S. operations specifications of a new entrant foreign air carrier must comply with...

Space Shuttle Crawler Transporter Vibration Analysis in Support of Rollout Fatigue Load Spectra Verification Program

NASA Technical Reports Server (NTRS)

Margasahayam, Ravi N.; Meyer, Karl A.; Nerolich, Shaun M.; Burton, Roy C.; Gosselin, Armand M.

2004-01-01

The Crawler Transporter (CT), designed and built for the Apollo Program in the 1960's and surpassing its initial operational life, has become an integral part of the Space Shuttle Program (SSP). The CT transports the Space Shuttle Vehicle (SSV) stack, atop the Mobile Launch Platform (MLP), from the Vehicle Assembly Building (VAB) to the launch pad. This support structure provides hydraulic jacking, leveling and load equalization for the 12 million pound stack on its 3.5-5.0 mile rollout to the launch pad. Major elements of the SSV, consisting of the orbiter, solid rocket boosters (SRB) and external tank (ET) have required fatigue analyses as part of the mission life certification. Compared to rollout vibration, the SSV sees relatively high vibration loads during launch, ascent, descent and landing phases of the mission. Although preliminary measured SRB vibration levels during rollout were of low amplitude and frequency, the duration of the rollout phase is typically high, from 5-6 hours. As part of an expanded mission life assessment, additional certification effort was initiated to define fatigue load spectra for rollout. This study addresses the CT vibration analyses in support of the rollout fatigue study. Structural models developed for modal and vibration analyses were used to identify unique CT, CT/MLP and CT/MLP/SRB vibration characteristics for comparison to instrumented rollout tests. Whereas the main structural and vibration characteristics of the SSV are well defined, minimum analytical and vibration test data on the Crawler Transporter were available. Unique vibration characteristics of the CT are attributable to the drive mechanism, hydraulic jacking system, structural framing and the CT-to-MLP support pad restraints. Initial tests performed on the CT/MLP/SRB configuration showed reasonable correlation with predicted mode shapes and frequencies.

Parametric estimates for the receiver operating characteristic curve generalization for non-monotone relationships.

PubMed

Martínez-Camblor, Pablo; Pardo-Fernández, Juan C

2017-01-01

Diagnostic procedures are based on establishing certain conditions and then checking if those conditions are satisfied by a given individual. When the diagnostic procedure is based on a continuous marker, this is equivalent to fix a region or classification subset and then check if the observed value of the marker belongs to that region. Receiver operating characteristic curve is a valuable and popular tool to study and compare the diagnostic ability of a given marker. Besides, the area under the receiver operating characteristic curve is frequently used as an index of the global discrimination ability. This paper revises and widens the scope of the receiver operating characteristic curve definition by setting the classification subsets in which the final decision is based in the spotlight of the analysis. We revise the definition of the receiver operating characteristic curve in terms of particular classes of classification subsets and then focus on a receiver operating characteristic curve generalization for situations in which both low and high values of the marker are associated with more probability of having the studied characteristic. Parametric and non-parametric estimators of the receiver operating characteristic curve generalization are investigated. Monte Carlo studies and real data examples illustrate their practical performance.

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

30 CFR 47.2 - Operators and chemicals covered; initial miner training.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Operators and chemicals covered; initial miner... Training § 47.2 Operators and chemicals covered; initial miner training. (a) This part applies to any operator producing or using a hazardous chemical to which a miner can be exposed under normal conditions of...

Changes in skin reactivity and associated factors in patients sensitized to house dust mites after 1 year of allergen-specific immunotherapy.

PubMed

Son, Jeong-Yeop; Jung, Mann-Hong; Koh, Kwang-Wook; Park, Eun-Kee; Heo, Jeong-Hoon; Choi, Gil-Soon; Kim, Hee-Kyoo

2017-04-01

Allergen-specific immunotherapy (SIT) can significantly improve symptoms and reduce the need for symptomatic medication. The aim of this study was to investigate changes in skin reactivity to house dust mites (HDMs) as an immunologic response and associated factors after 1 year of immunotherapy. A total of 80 patients with allergic airway diseases who received subcutaneous SIT with HDMs from 2009 to 2014 were evaluated. The investigated parameters were basic demographic characteristics, skin reactivity and specific IgE for HDM, serum total IgE level, blood eosinophil counts, and medication score. The mean levels of skin reactivity to HDMs, blood eosinophil counts, and medication scores after 1 year were significantly reduced from baseline. In univariate comparison of the changes in skin reactivity to HDMs, age ≤30 years, HDMs only as target of immunotherapy, and high initial skin reactivity (≥2) to HDMs were significantly associated with the reduction in skin test reactivity. In multivariate analysis, high initial skin reactivity and HDMs only as target allergens were significantly associated with changes in skin reactivity to HDMs. In the receiver operating characteristic curve of the initial mean skin reactivity to HDMs for more than 50% reduction, the optimal cutoff value was 2.14. This study showed significant reductions in allergen skin reactivity to HDMs after 1 year of immunotherapy in patients sensitized to HDMs. The extent of initial allergen skin reactivity and only HDMs as target allergen were important predictive factors for changes in skin reactivity.

A predictive model for diagnosing bipolar disorder based on the clinical characteristics of major depressive episodes in Chinese population.

PubMed

Gan, Zhaoyu; Diao, Feici; Wei, Qinling; Wu, Xiaoli; Cheng, Minfeng; Guan, Nianhong; Zhang, Ming; Zhang, Jinbei

2011-11-01

A correct timely diagnosis of bipolar depression remains a big challenge for clinicians. This study aimed to develop a clinical characteristic based model to predict the diagnosis of bipolar disorder among patients with current major depressive episodes. A prospective study was carried out on 344 patients with current major depressive episodes, with 268 completing 1-year follow-up. Data were collected through structured interviews. Univariate binary logistic regression was conducted to select potential predictive variables among 19 initial variables, and then multivariate binary logistic regression was performed to analyze the combination of risk factors and build a predictive model. Receiver operating characteristic (ROC) curve was plotted. Of 19 initial variables, 13 variables were preliminarily selected, and then forward stepwise exercise produced a final model consisting of 6 variables: age at first onset, maximum duration of depressive episodes, somatalgia, hypersomnia, diurnal variation of mood, irritability. The correct prediction rate of this model was 78% (95%CI: 75%-86%) and the area under the ROC curve was 0.85 (95%CI: 0.80-0.90). The cut-off point for age at first onset was 28.5 years old, while the cut-off point for maximum duration of depressive episode was 7.5 months. The limitations of this study include small sample size, relatively short follow-up period and lack of treatment information. Our predictive models based on six clinical characteristics of major depressive episodes prove to be robust and can help differentiate bipolar depression from unipolar depression. Copyright © 2011 Elsevier B.V. All rights reserved.

Characteristics of the group of radiologists that benefits the most using Breast Screen Reader Assessment Strategy (BREAST)

NASA Astrophysics Data System (ADS)

Ganesan, A.; Alakhras, M.; Brennan, P. C.; Lee, W.; Tapia, K.; Mello-Thoms, C.

2018-03-01

Purpose: To determine the impact of Breast Screen Reader Assessment Strategy (BREAST) over time in improving radiologists' breast cancer detection performance, and to identify the group of radiologists that benefit the most by using BREAST as a training tool. Materials and Methods: Thirty-six radiologists who completed three case-sets offered by BREAST were included in this study. The case-sets were arranged in radiologists' chronological order of completion and five performance measures (sensitivity, specificity, location sensitivity, receiver operating characteristics area under the curve (ROC AUC) and jackknife alternative free-response receiver operating characteristic (JAFROC) figure-of-merit (FOM)), available from BREAST, were compared between case-sets to determine the level of improvement achieved. The radiologists were then grouped based on their characteristics and the above performance measures between the case-sets were compared. Paired t-tests or Wilcoxon signed-rank tests with statistical significance set at p < 0.05 were used to compare the performance measures. Results: Significant improvement was demonstrated in radiologists' case-set performance in terms of location sensitivity and JAFROC FOM over the years, and radiologists' location sensitivity and JAFROC FOM showed significant improvement irrespective of their characteristics. In terms of ROC AUC, significant improvement was shown for radiologists who were reading screen mammograms for more than 7 years and spent more than 9 hours per week reading mammograms. Conclusion: Engaging with case-sets appears to enhance radiologists' performance suggesting the important value of initiatives such as BREAST. However, such performance enhancement was not shown for everyone, highlighting the need to tailor the BREAST platform to benefit all radiologists.

An Image Encryption Algorithm Utilizing Julia Sets and Hilbert Curves

PubMed Central

Sun, Yuanyuan; Chen, Lina; Xu, Rudan; Kong, Ruiqing

2014-01-01

Image encryption is an important and effective technique to protect image security. In this paper, a novel image encryption algorithm combining Julia sets and Hilbert curves is proposed. The algorithm utilizes Julia sets’ parameters to generate a random sequence as the initial keys and gets the final encryption keys by scrambling the initial keys through the Hilbert curve. The final cipher image is obtained by modulo arithmetic and diffuse operation. In this method, it needs only a few parameters for the key generation, which greatly reduces the storage space. Moreover, because of the Julia sets’ properties, such as infiniteness and chaotic characteristics, the keys have high sensitivity even to a tiny perturbation. The experimental results indicate that the algorithm has large key space, good statistical property, high sensitivity for the keys, and effective resistance to the chosen-plaintext attack. PMID:24404181

Comparison of the quench and fault current limiting characteristics of the flux-coupling type SFCL with single and three-phase transformer

NASA Astrophysics Data System (ADS)

Jung, Byung Ik; Cho, Yong Sun; Park, Hyoung Min; Chung, Dong Chul; Choi, Hyo Sang

2013-01-01

The South Korean power grid has a network structure for the flexible operation of the system. The continuously increasing power demand necessitated the increase of power facilities, which decreased the impedance in the power system. As a result, the size of the fault current in the event of a system fault increased. As this increased fault current size is threatening the breaking capacity of the circuit breaker, the main protective device, a solution to this problem is needed. The superconducting fault current limiter (SFCL) has been designed to address this problem. SFCL supports the stable operation of the circuit breaker through its excellent fault-current-limiting operation [1-5]. In this paper, the quench and fault current limiting characteristics of the flux-coupling-type SFCL with one three-phase transformer were compared with those of the same SFCL type but with three single-phase transformers. In the case of the three-phase transformers, both the superconducting elements of the fault and sound phases were quenched, whereas in the case of the single-phase transformer, only that of the fault phase was quenched. For the fault current limiting rate, both cases showed similar rates for the single line-to-ground fault, but for the three-wire earth fault, the fault current limiting rate of the single-phase transformer was over 90% whereas that of the three-phase transformer was about 60%. It appears that when the three-phase transformer was used, the limiting rate decreased because the fluxes by the fault current of each phase were linked in one core. When the power loads of the superconducting elements were compared by fault type, the initial (half-cycle) load was great when the single-phase transformer was applied, whereas for the three-phase transformer, its power load was slightly lower at the initial stage but became greater after the half fault cycle.

Simulation study of a new inverse-pinch high Coulomb transfer switch

NASA Technical Reports Server (NTRS)

Choi, S. H.

1984-01-01

A simulation study of a simplified model of a high coulomb transfer switch is performed. The switch operates in an inverse pinch geometry formed by an all metal chamber, which greatly reduces hot spot formations on the electrode surfaces. Advantages of the switch over the conventional switches are longer useful life, higher current capability and lower inductance, which improves the characteristics required for a high repetition rate switch. The simulation determines the design parameters by analytical computations and comparison with the experimentally measured risetime, current handling capability, electrode damage, and hold-off voltages. The parameters of initial switch design can be determined for the anticipated switch performance. Results are in agreement with the experiment results. Although the model is simplified, the switch characteristics such as risetime, current handling capability, electrode damages, and hold-off voltages are accurately determined.

Energy efficient engine: Flight propulsion system preliminary analysis and design

NASA Technical Reports Server (NTRS)

Johnston, R. P.; Beitler, R. S.; Bobinger, R. O.; Broman, C. L.; Gravitt, R. D.; Heineke, H.; Holloway, P. R.; Klem, J. S.; Nash, D. O.; Ortiz, P.

1980-01-01

The characteristics of an advanced flight propulsion system (FPS), suitable for introduction in the late 1980's to early 1990's, was more fully defined. It was determined that all goals for efficiency, environmental considerations, and economics could be met or exceeded with the possible exception of NOx emission. In evaluating the FPS, all aspects were considered including component design, performance, weight, initial cost, maintenance cost, engine system integration (including nacelle), and aircraft integration considerations. The current FPS installed specific fuel consumption was reduced 14.2% from that of the CF6-50C reference engine. When integrated into an advanced, subsonic, study transport, the FPS produced a fuel burn savings of 15 to 23% and a direct operating cost reduction of 5 to 12% depending on the mission and study aircraft characteristics relative to the reference engine.

Preliminary Validation of the Small Aircraft Transportation System Higher Volume Operations (SATS HVO) Concept

NASA Technical Reports Server (NTRS)

Williams, Daniel; Consiglio, Maria; Murdoch, Jennifer; Adams, Catherine

2004-01-01

This document provides a preliminary validation of the Small Aircraft Transportation System (SATS) Higher Volume Operations (HVO) concept for normal conditions. Initial results reveal that the concept provides reduced air traffic delays when compared to current operations without increasing pilot workload. Characteristic to the SATS HVO concept is the establishment of a newly defined area of flight operations called a Self-Controlled Area (SCA) which would be activated by air traffic control (ATC) around designated non-towered, non-radar airports. During periods of poor visibility, SATS pilots would take responsibility for separation assurance between their aircraft and other similarly equipped aircraft in the SCA. Using onboard equipment and simple instrument flight procedures, they would then be better able to approach and land at the airport or depart from it. This concept would also require a new, ground-based automation system, typically located at the airport that would provide appropriate sequencing information to the arriving aircraft. Further validation of the SATS HVO concept is required and is the subject of ongoing research and subsequent publications.

Thermal Characterization Study of Lithium-Ion Cells

NASA Technical Reports Server (NTRS)

Britton, Doris L.; Miller, Thomas B.; Bennett, William R.

2007-01-01

The primary challenge in designing a full scale lithium-ion (Li-ion) battery system is safety under both normal operating as well as abusive conditions. The normal conditions involve expected charge/discharge cycles and it is known that heat evolves in batteries during those cycles. This is a major concern in the design for high power applications and careful thermal management is necessary to alleviate this concern. An emerging thermal measurement technology, such as the electrochemical calorimetric of batteries, will aid in the development of advanced, safe battery system. To support this technology, several "commercial-off-the-shelf" (COTS) Li-ion cells with different chemistries and designs are being evaluated for different cycling regimes at a given operating temperature. The Accelerated Rate Calorimeter (ARC)-Arbin cycler setup is used to measure the temperature, voltage, and current of the cells at different charge/discharge rates. Initial results demonstrated good cell cyclability. During the cycle testing, the cell exhibited an endothermic cooling in the initial part of the charge cycle. The discharge portion of the cycle is exothermic during the entire discharge period. The presence of an endothermic reaction indicates a significant entropy effect during the beginning of charge cycle. Further studies will be performed to understand the thermal characteristics of the Li-ion cells at the different operating conditions. The effects on the thermal response on cell aging and states-of-charge will also be identified.

Treatment of cyanide containing wastewater using cavitation based approach.

PubMed

Jawale, Rajashree H; Gogate, Parag R; Pandit, Aniruddha B

2014-07-01

Industrial wastewater streams containing high concentrations of biorefractory materials like cyanides should ideally be treated at source. In the present work, degradation of potassium ferrocyanide (K4Fe(CN)6) as a model pollutant has been investigated using cavitational reactors with possible intensification studies using different approaches. Effect of different operating parameters such as initial concentration, temperature and pH on the extent of degradation using acoustic cavitation has been investigated. For the case of hydrodynamic cavitation, flow characteristics of cavitating device (venturi) have been established initially followed by the effect of inlet pressure and pH on the extent of degradation. Under the optimized set of operating parameters, the addition of hydrogen peroxide (ratio of K4Fe(CN)6:H2O2 varied from 1:1 to 1:30 mol basis) as process intensifying approach has been investigated. The present work has conclusively established that under the set of optimized operating parameters, cavitation can be effectively used for degradation of potassium ferrocyanide. The comparative study of hydrodynamic cavitation and acoustic cavitation suggested that hydrodynamic cavitation is more energy efficient and gives higher degradation as compared to acoustic cavitation for equivalent power/energy dissipation. The present work is the first one to report comparison of cavitation based treatment schemes for degradation of cyanide containing wastewaters. Copyright © 2014 Elsevier B.V. All rights reserved.

Truck characteristics for use in highway design and operation. Volume II, Appendices

DOT National Transportation Integrated Search

1990-08-01

Highway geometric design and traffic operations are based in part on consideration of vehicle characteristics. However, many of the current highway design and operational criteria are based on passenger car characteristics, even though truck characte...

49 CFR 236.717 - Characteristics, operating.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Characteristics, operating. 236.717 Section 236.717 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... § 236.717 Characteristics, operating. The measure of electrical values at which electrical or electronic...

49 CFR 236.717 - Characteristics, operating.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Characteristics, operating. 236.717 Section 236.717 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... § 236.717 Characteristics, operating. The measure of electrical values at which electrical or electronic...

Formation of inhalable rifampicin-poly(L-lactide) microparticles by supercritical anti-solvent process.

PubMed

Patomchaiviwat, Vipaluk; Paeratakul, Ornlaksana; Kulvanich, Poj

2008-01-01

Formation of inhalable microparticles containing rifampicin and poly(L-lactide) (L-PLA) by using supercritical anti-solvent process (SAS) was investigated. The solutions of drug and polymer in methylene chloride were sprayed into supercritical carbon dioxide. The effect of polymer content and operating conditions, temperature, pressure, carbon dioxide molar fraction, and concentration of solution, on product characteristics were studied. The prepared microparticles were characterized with respect to their morphology, particle size and size distribution, drug content, drug loading efficiency, and drug release characteristic. Discrete, spherical microparticles were obtained at high polymer:drug ratios of 7:3, 8:2, and 9:1. The shape of L-PLA microparticles became more irregular and agglomerated with decreasing polymer content. Microparticles with polymer content higher than 60% exhibited volumetric mean diameter less than 5 microm, but percent drug loading efficiency was relatively low. Drug-loaded microparticles containing 70% and 80% L-PLA showed a sustainable drug release property without initial burst release. Operating temperature level influenced on mean size and size distribution of microparticles. The operating pressure and carbon dioxide molar fraction in the range investigated were unlikely to have an effect on microparticle formation. An increasing concentration of feed solution provided larger size microparticles. Rifampicin-loaded L-PLA microparticles could be produced by SAS in a size range suitable for dry powder inhaler formulation.

Critical engine system design characteristics for SSTO vehicles

NASA Astrophysics Data System (ADS)

Fanciullo, Thomas J.; Judd, D. C.; Obrien, C. J.

1992-02-01

Engine system design characteristics are summarized for typical vertical take-off and landing (VTOL) and vertical take-off and horizontal landing (VTHL) Strategic Defense Initiative Organization (SDIO) single stage to orbit (SSTO) vehicles utilizing plug nozzle configurations. Power cycle selection trades involved the unique modular platelet engine (MPE) with the use of (1) LO2 and LH2 at fixed and variable mixture ratios, (2) LO2 and propane or RP-1, and (3) dual fuels (LO2 with LH2 and C3H8). The number of thrust cells and modules were optimized. Dual chamber bell and a cluster of conventional bell nozzle configurations were examined for comparison with the plug configuration. Thrust modulation (throttling) was selected for thrust vector control. Installed thrust ratings were established to provide an additional 20 percent overthrust capability for engine out operation. Turbopumps were designed to operate at subcritical speeds to facilitate a wide range of throttling and long life. A unique dual spool arrangement with hydrostatic bearings was selected for the LH2 turbopump. Controls and health monitoring with expert systems for diagnostics are critical subsystems to ensure minimum maintenance and supportability for a less than seven day turnaround. The use of an idle mode start, in conjunction with automated health condition monitoring, allows the rocket propulsion system to operate reliably in the manner of present day aircraft propulsion.

Jackknife variance of the partial area under the empirical receiver operating characteristic curve.

PubMed

Bandos, Andriy I; Guo, Ben; Gur, David

2017-04-01

Receiver operating characteristic analysis provides an important methodology for assessing traditional (e.g., imaging technologies and clinical practices) and new (e.g., genomic studies, biomarker development) diagnostic problems. The area under the clinically/practically relevant part of the receiver operating characteristic curve (partial area or partial area under the receiver operating characteristic curve) is an important performance index summarizing diagnostic accuracy at multiple operating points (decision thresholds) that are relevant to actual clinical practice. A robust estimate of the partial area under the receiver operating characteristic curve is provided by the area under the corresponding part of the empirical receiver operating characteristic curve. We derive a closed-form expression for the jackknife variance of the partial area under the empirical receiver operating characteristic curve. Using the derived analytical expression, we investigate the differences between the jackknife variance and a conventional variance estimator. The relative properties in finite samples are demonstrated in a simulation study. The developed formula enables an easy way to estimate the variance of the empirical partial area under the receiver operating characteristic curve, thereby substantially reducing the computation burden, and provides important insight into the structure of the variability. We demonstrate that when compared with the conventional approach, the jackknife variance has substantially smaller bias, and leads to a more appropriate type I error rate of the Wald-type test. The use of the jackknife variance is illustrated in the analysis of a data set from a diagnostic imaging study.

Towards Improved Forecasts of Atmospheric and Oceanic Circulations over the Complex Terrain of the Eastern Mediterranean

NASA Technical Reports Server (NTRS)

Chronis, Themis; Case, Jonathan L.; Papadopoulos, Anastasios; Anagnostou, Emmanouil N.; Mecikalski, John R.; Haines, Stephanie L.

2008-01-01

Forecasting atmospheric and oceanic circulations accurately over the Eastern Mediterranean has proved to be an exceptional challenge. The existence of fine-scale topographic variability (land/sea coverage) and seasonal dynamics variations can create strong spatial gradients in temperature, wind and other state variables, which numerical models may have difficulty capturing. The Hellenic Center for Marine Research (HCMR) is one of the main operational centers for wave forecasting in the eastern Mediterranean. Currently, HCMR's operational numerical weather/ocean prediction model is based on the coupled Eta/Princeton Ocean Model (POM). Since 1999, HCMR has also operated the POSEIDON floating buoys as a means of state-of-the-art, real-time observations of several oceanic and surface atmospheric variables. This study attempts a first assessment at improving both atmospheric and oceanic prediction by initializing a regional Numerical Weather Prediction (NWP) model with high-resolution sea surface temperatures (SST) from remotely sensed platforms in order to capture the small-scale characteristics.

Edge systems in the deep ocean

NASA Astrophysics Data System (ADS)

Coon, Andrew; Earp, Samuel L.

2010-04-01

DARPA has initiated a program to explore persistent presence in the deep ocean. The deep ocean is difficult to access and presents a hostile environment. Persistent operations in the deep ocean will require new technology for energy, communications and autonomous operations. Several fundamental characteristics of the deep ocean shape any potential system architecture. The deep sea presents acoustic sensing opportunities that may provide significantly enhanced sensing footprints relative to sensors deployed at traditional depths. Communication limitations drive solutions towards autonomous operation of the platforms and automation of data collection and processing. Access to the seabed presents an opportunity for fixed infrastructure with no important limitations on size and weight. Difficult access and persistence impose requirements for long-life energy sources and potentially energy harvesting. The ocean is immense, so there is a need to scale the system footprint for presence over tens of thousands and perhaps hundreds of thousands of square nautical miles. This paper focuses on the aspect of distributed sensing, and the engineering of networks of sensors to cover the required footprint.

Initial Operation and Shakedown of the Nuclear Thermal Rocket Element Environmental Simulator (NTREES)

NASA Technical Reports Server (NTRS)

Emrich, William J., Jr.

2014-01-01

To support the on-going nuclear thermal propulsion effort, a state-of-the-art non nuclear experimental test setup has been constructed to evaluate the performance characteristics of candidate fuel element materials and geometries in representative environments. The facility to perform this testing is referred to as the Nuclear Thermal Rocket Element Environment Simulator (NTREES). This device can simulate the environmental conditions (minus the radiation) to which nuclear rocket fuel components will be subjected during reactor operation. Prototypical fuel elements mounted in the simulator are inductively heated in such a manner so as to accurately reproduce the temperatures and heat fluxes which would normally occur as a result of nuclear fission in addition to being exposed to flowing hydrogen. Recent upgrades to NTREES now allow power levels 24 times greater than those achievable in the previous facility configuration. This higher power operation will allow near prototypical power densities and flows to finally be achieved in most prototypical fuel elements.

Operating characteristics of 120-millimeter-bore ball bearings at 3 million DN

NASA Technical Reports Server (NTRS)

Zaretsky, E. V.; Bamberger, E. N.; Signer, H.

1974-01-01

A parametric study was performed with split inner-race 120-mm-bore angular-contact ball bearings at a speed of 25,000 rpm (3 million DN) at initial contact angles of 20 deg and 24 deg. Provisions were made for outer- and inner-race cooling and for injection of lubricant into the bearing through a number of radial holes in the split inner-race of the bearing. Oil flow and coolant rate to the bearing was controlled and varied for a total up to approximately 3.2 gal/min. Bearing temperature was found to decrease as the total lubricant flow to the bearing increased. However, at intermediate flow rates temperature began to increase with increasing flow. Power consumption increased with increasing flow rate. Bearing operating temperature, differences in temperatures between the inner and outer races, and bearing power consumption can be tuned to any desirable operating requirement. Cage speed increased by not more than 2 percent with increasing oil flow to the inner race.

Safety illusion and error trap in a collectively-operated machine accident.

PubMed

de Almeida, Ildeberto Muniz; Nobre, Hildeberto; do Amaral Dias, Maria Dionísia; Vilela, Rodolfo Andrade Gouveia

2012-01-01

Workplace accidents involving machines are relevant for their magnitude and their impacts on worker health. Despite consolidated critical statements, explanation centered on errors of operators remains predominant with industry professionals, hampering preventive measures and the improvement of production-system reliability. Several initiatives were adopted by enforcement agencies in partnership with universities to stimulate production and diffusion of analysis methodologies with a systemic approach. Starting from one accident case that occurred with a worker who operated a brake-clutch type mechanical press, the article explores cognitive aspects and the existence of traps in the operation of this machine. It deals with a large-sized press that, despite being endowed with a light curtain in areas of access to the pressing zone, did not meet legal requirements. The safety devices gave rise to an illusion of safety, permitting activation of the machine when a worker was still found within the operational zone. Preventive interventions must stimulate the tailoring of systems to the characteristics of workers, minimizing the creation of traps and encouraging safety policies and practices that replace judgments of behaviors that participate in accidents by analyses of reasons that lead workers to act in that manner.

OMV man/system simulation integration: A preliminary analysis and recommendation

NASA Technical Reports Server (NTRS)

Rogers, Jon G.

1988-01-01

The Orbital Maneuvering Vehicle (OMV) presents a series of challenges to the human operator. Some are unique to the OMV system itself, and are largely due to remote control versus control from the cockpit. Other challenges are not necessarily unique to the OMV, but are characteristic of many man-machine space flight systems. All of these challenges affect the operator's ability to perform his portion of the mission, and could lead to human error which might jeopardize the vehicle, mission, or both. It is imperative to make every effort to design the control and displays to facilitate the operator's task. The experimental program should address the perceptual, mediational, and motor dimensions of operator performance. With this in mind, a literature review with relevant design considerations was initiated, and a comprehensive outline of control/display parameters were developed. Out of this, a series of questions not answered in the literature was derived which can be converted into experimental protocols for the simulation program. A major task of the aircraft pilot as well as the OMV operator is prediction. Certain display principles have proved to enhance the pilot's ability to predict. A brief examination of some of these principles in relationship to OMV may be useful.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Widjaja, Ongky, E-mail: wijayaongky@yahoo.co.id; Arie, Arenst Andreas, E-mail: arenst@unpar.ac.id; Halim, Martin

In this work, kerosene oil based nanocarbons were synthesized by a nebulized spray pyrolysis method. This method was conducted at temperature of 700°C under a nitrogen inert atmospheric condition. Activated carbon and ferrocene were used as substrate and catalyst, respectively. Initially, ferrocene was dissolved in the oil with fixed concentration of 0.02 g/ml. The pyrolysis reaction was carried out by varying the operating time of 15, 30 and 45 minutes. The main aim of this work was to investigate the effect of varying the operation time on the morphology and structural characteristics of as-prepared carbon products. The morphology and structural characteristicsmore » of synthesized nanocarbons were examined by Scanning Electron Microscope (SEM), Transmission Electron Microscopy (TEM), and Raman Spectroscopy, respectively. SEM and TEM observations showed that nano carbons were formed as agglomerated carbon nanospheres (CNSs) and graphene for all variation of operating time. Furthermore, it was observed that the size of agglomerated CNSs was proportional with the operating time from 15 to 45 minutes. Raman analysis showed that the ratio between graphite like and disorder carbon structure (I{sub G}/I{sub D})of carbon samples increased from operating time of 15 to 30 minutes, however the ratio decreased from 30 minutes to 45 minutes.« less

Application of excitation and emission matrix fluorescence (EEM) and UV-vis absorption to monitor the characteristics of Alizarin Red S (ARS) during electro-Fenton degradation process.

PubMed

Lai, Bo; Zhou, Yuexi; Wang, Juling; Yang, Zhishan; Chen, Zhiqiang

2013-11-01

Oxidative degradation of Alizarin Red S (ARS) in aqueous solutions by using electro-Fenton was studied. At first, effect of operating parameters such as current density, aeration rate and initial pH on the degradation of ARS were studied by using UV-vis spectrum, respectively. Then, under the optimal operating conditions (current density: 10.0mAcm(-2), aeration rate: 1000mLmin(-1), initial pH: 2.8), the identification of degradation products of ARS was carried out by using GC-MS and HPLC, meanwhile its degradation pathway was proposed according to the intermediates. Considering the location, intensity and intensity ratio of fluorescence center peak of the ARS in aqueous solution, a convenient and quick monitoring method by using excitation-emission matrix fluorescence spectrum technology was developed to monitor the degradation degree of ARS through electro-Fenton process. Furthermore, it is suggested that the developed method would be promising for the quick analysis and evaluation of the degradation degree of the pollutants with π-conjugated system. Copyright © 2013 Elsevier Ltd. All rights reserved.

Mexican Space Weather Service (SCiESMEX)

NASA Astrophysics Data System (ADS)

Gonzalez-Esparza, J. A.; De la Luz, V.; Corona-Romero, P.; Mejia-Ambriz, J. C.; Gonzalez, L. X.; Sergeeva, M. A.; Romero-Hernandez, E.; Aguilar-Rodriguez, E.

2017-01-01

Legislative modifications of the General Civil Protection Law in Mexico in 2014 included specific references to space hazards and space weather phenomena. The legislation is consistent with United Nations promotion of international engagement and cooperation on space weather awareness, studies, and monitoring. These internal and external conditions motivated the creation of a space weather service in Mexico. The Mexican Space Weather Service (SCiESMEX in Spanish) (www.sciesmex.unam.mx) was initiated in October 2014 and is operated by the Institute of Geophysics at the Universidad Nacional Autonoma de Mexico (UNAM). SCiESMEX became a Regional Warning Center of the International Space Environment Services (ISES) in June 2015. We present the characteristics of the service, some products, and the initial actions for developing a space weather strategy in Mexico. The service operates a computing infrastructure including a web application, data repository, and a high-performance computing server to run numerical models. SCiESMEX uses data of the ground-based instrumental network of the National Space Weather Laboratory (LANCE), covering solar radio burst emissions, solar wind and interplanetary disturbances (by interplanetary scintillation observations), geomagnetic measurements, and analysis of the total electron content (TEC) of the ionosphere (by employing data from local networks of GPS receiver stations).

Manufacturing implementation of off-line programming for the Space Shuttle Main Engines

NASA Technical Reports Server (NTRS)

Sliwinski, K. E.; Pierson, B. L.; Anderson, R. R.; Guthmiller, W. A.

1989-01-01

An account is given of the efforts made to implement an off-line programming (OLP) system for a gas tungsten arc welding robot in actual manufacturing operations, namely those involved in the manufacture of the SSMEs. In conjunction with a real-time sensor control system, the OLP constitutes the Advanced Robotic Welding System, or 'AROWS'. OLP's task is to develop a robot-motion path without the initial use of the robot to 'teach' the characteristics of such motion; actual process parameters are recorded by OLP and correlated with the position along the weld.

Rotorcraft flight-propulsion control integration: An eclectic design concept

NASA Technical Reports Server (NTRS)

Mihaloew, James R.; Ballin, Mark G.; Ruttledge, D. C. G.

1988-01-01

The NASA Ames and Lewis Research Centers, in conjunction with the Army Research and Technology Laboratories, have initiated and partially completed a joint research program focused on improving the performance, maneuverability, and operating characteristics of rotorcraft by integrating the flight and propulsion controls. The background of the program, its supporting programs, its goals and objectives, and an approach to accomplish them are discussed. Results of the modern control governor design of the General Electric T700 engine and the Rotorcraft Integrated Flight-Propulsion Control Study, which were key elements of the program, are also presented.

N.G. Basov and early works on semiconductor lasers at P.N. Lebedev Physics Institute

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eliseev, P G

2012-12-31

A survey is presented of works on creation and investigation of semiconductor lasers during 1957 - 1977 at the P.N. Lebedev Physics Institute. Many of these works were initiated by N.G. Basov, starting from pre-laser time, when N.G. Basov and his coworkers formulated principal conditions of creation of lasers on interband transitions in semiconductors. Main directions of further works were diode lasers based on various materials and structures, their characteristics of output power, high-speed operation and reliability. (special issue devoted to the 90th anniversary of n.g. basov)

Mechanical behaviour of cerclage material consisting of silicon rubber.

PubMed

Hinrichsen, G; Eberhardt, A; Springer, H

1979-09-01

Silicon rubber specimens of circular or rectangular cross-section (cross-section area between ca. 2 and 7 mm2) are used as cerclage bands. A series of commercial cerclage elements was investigated for mechanical characteristics, such as stress-strain behaviour and modulus of elasticity, using a tensile-testing machine. Large differences in these properties exist among the various specimens. Moreover, time-dependent effects, such as stress-relaxation, retardation, and creep, were analysed by the present investigations. One has to take into consideration that the initial length and stress of the cerclage band vary significantly with time after the operation.

Choosing the function of mechanical properties of grounds and rock formations due to their heterogeneity

NASA Astrophysics Data System (ADS)

Frolova, Irina; Agakhanov, Murad

2018-03-01

The development of computing techniques to analyze underground structures, buildings in high-rise construction that would fully take account of the conditions of their design and operation, as well as the real material properties, is one of the important trends in structural mechanics. For the territory in high-rise construction it is necessary to monitor the deformations of the soil surface. When high-rise construction is recommended to take into account the rheological properties and temperature deformations of the soil, the effect of temperature on the mechanical characteristics of the surrounding massif. Similar tasks also arise in the creation and operation of underground parts of high-rise construction, which are used for various purposes. These parts of the structures are surrounded by rock massifs of various materials. The actual mechanical characteristics of such materials must be taken into account. The objective property of nearly all materials is their non-homogeneity, both natural and technological. The work addresses the matters of building nonhomogeneous media initial models based on the experimental evidence. This made it possible to approximate real dependencies and obtain the appropriate functions in a simple and convenient way.

A Pilot Study Investigating Employee Utilization of Corporate Telehealth Services

PubMed Central

Edgerton, Seena Shazowee

2017-01-01

In line with the vision of the University of Mississippi Medical Center (UMMC) to improve health outcomes and eliminate healthcare disparities in Mississippi, a corporate telehealth program was initiated beginning May 2014. A descriptive study was performed to discover common characteristics among enrolled employee users who took advantage of UMMC's corporate telehealth services offered in their workplace throughout the program's first year of operation. This pilot study examined the number of videoconference visits (e-visits) throughout the first year of operation, from May 2014 through April 2015. This examination of common user traits may help identify characteristics that indicate an employee's likelihood of using corporate telehealth. The study revealed the highest use among employees between the ages of 30 and 49 years and among those who attended a formal orientation session including both the employer's human resources personnel and a UMMC corporate telehealth representative. Corporations may find that offering corporate telehealth serves as an effective means to reduce overall healthcare costs and productivity loss. Furthermore, the identification of common variables in this study may help the UMMC corporate telehealth program develop additional methods to reach and assist employees who may not otherwise seek medical treatment. PMID:29118684

Investigation, Modeling, and Analysis of Integrated Metroplex Arrival and Departure Coordination Concepts

NASA Technical Reports Server (NTRS)

Clarke, John-Paul B.; Brooks, James; McClain, Evan; Paladhi, Anwesha Roy; Li, Leihong; Schleicher, David; Saraf, Aditya; Timar, Sebastian; Crisp, Don; Bertino, Jason;

Initial evaluation of commercially available InGaAsP DFB laser diodes for use in high-speed digital fiber optic transceivers

NASA Technical Reports Server (NTRS)

Cook, Anthony L.; Hendricks, Herbert D.

1990-01-01

NASA has been pursuing the development of high-speed fiber-optic transceivers for use in a number of space data system applications. Current efforts are directed toward a high-performance all-integrated-circuit transceiver operating up to the 3-5 Gb/s range. Details of the evaluation and selection of candidate high-speed optical sources to be used in the space-qualified high-performance transceiver are presented. Data on the performance of commercially available DFB (distributed feedback) lasers are presented, and their performance relative to each other and to their structural design with regard to their use in high-performance fiber-optic transceivers is discussed. The DFB lasers were obtained from seven commercial manufacturers. The data taken on each laser included threshold current, differential quantum efficiency, CW side mode suppression radio, wavelength temperature coefficient, threshold temperature coefficient, natural linewidth, and far field pattern. It was found that laser diodes with buried heterostructures and first-order gratings had, in general, the best CW operating characteristics. The modulated characteristics of the DFB laser diodes are emphasized. Modulated linewidth, modulated side mode suppression ratio, and frequency response are discussed.

Simultaneous development of laparoscopy and robotics provides acceptable perioperative outcomes and shows robotics to have a faster learning curve and to be overall faster in rectal cancer surgery: analysis of novice MIS surgeon learning curves.

PubMed

Melich, George; Hong, Young Ki; Kim, Jieun; Hur, Hyuk; Baik, Seung Hyuk; Kim, Nam Kyu; Sender Liberman, A; Min, Byung Soh

2015-03-01

Laparoscopy offers some evidence of benefit compared to open rectal surgery. Robotic rectal surgery is evolving into an accepted approach. The objective was to analyze and compare laparoscopic and robotic rectal surgery learning curves with respect to operative times and perioperative outcomes for a novice minimally invasive colorectal surgeon. One hundred and six laparoscopic and 92 robotic LAR rectal surgery cases were analyzed. All surgeries were performed by a surgeon who was primarily trained in open rectal surgery. Patient characteristics and perioperative outcomes were analyzed. Operative time and CUSUM plots were used for evaluating the learning curve for laparoscopic versus robotic LAR. Laparoscopic versus robotic LAR outcomes feature initial group operative times of 308 (291-325) min versus 397 (373-420) min and last group times of 220 (212-229) min versus 204 (196-211) min-reversed in favor of robotics; major complications of 4.7 versus 6.5 % (NS), resection margin involvement of 2.8 versus 4.4 % (NS), conversion rate of 3.8 versus 1.1 (NS), lymph node harvest of 16.3 versus 17.2 (NS), and estimated blood loss of 231 versus 201 cc (NS). Due to faster learning curves for extracorporeal phase and total mesorectal excision phase, the robotic surgery was observed to be faster than laparoscopic surgery after the initial 41 cases. CUSUM plots demonstrate acceptable perioperative surgical outcomes from the beginning of the study. Initial robotic operative times improved with practice rapidly and eventually became faster than those for laparoscopy. Developing both laparoscopic and robotic skills simultaneously can provide acceptable perioperative outcomes in rectal surgery. It might be suggested that in the current milieu of clashing interests between evolving technology and economic constrains, there might be advantages in embracing both approaches.

Evaluation of the British Columbia AIDS Information Line.

PubMed

Parsons, D C; Bell, M A; Gilchrist, L D

1991-01-01

We evaluated implementation of the British Columbia AIDS Information Line during its initial 15 weeks of operation. Data collected during daily operation of the line included call frequency, caller characteristics, response patterns, caller concerns and community referrals. Information on activities and resources required to implement the AIDS Line was also assembled. The study concluded that the advertising campaign sponsored by the provincial government and other AIDS-related media events had a strong impact on the frequency of calls made to the AIDS Line. However, the effect of both advertising and media events was of relatively short duration, suggesting that utilization of an AIDS information line is dependent on continuing promotional activities. The evaluation results demonstrate the importance of continuous collection of data online utilization, to track public awareness of and response to AIDS-related issues, and to facilitate planning of public education.

Basic design considerations for free-electron lasers driven by electron beams from RF accelerators

NASA Astrophysics Data System (ADS)

Gover, A.; Freund, H.; Granatstein, V. L.; McAdoo, J. H.; Tang, C.-M.

A design procedure and design criteria are derived for free-electron lasers driven by electron beams from RF accelerators. The procedure and criteria permit an estimate of the oscillation-buildup time and the laser output power of various FEL schemes: with waveguide resonator or open resonator, with initial seed-radiation injection or with spontaneous-emission radiation source, with a linear wiggler or with a helical wiggler. Expressions are derived for computing the various FEL parameters, allowing for the design and optimization of the FEL operational characteristics under ideal conditions or with nonideal design parameters that may be limited by technological or practical constraints. The design procedure enables one to derive engineering curves and scaling laws for the FEL operating parameters. This can be done most conveniently with a computer program based on flowcharts given in the appendices.

Modeling synchronous voltage source converters in transmission system planning studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kosterev, D.N.

1997-04-01

A Voltage Source Converter (VSC) can be beneficial to power utilities in many ways. To evaluate the VSC performance in potential applications, the device has to be represented appropriately in planning studies. This paper addresses VSC modeling for EMTP, powerflow, and transient stability studies. First, the VSC operating principles are overviewed, and the device model for EMTP studies is presented. The ratings of VSC components are discussed, and the device operating characteristics are derived based on these ratings. A powerflow model is presented and various control modes are proposed. A detailed stability model is developed, and its step-by-step initialization proceduremore » is described. A simplified stability model is also derived under stated assumptions. Finally, validation studies are performed to demonstrate performance of developed stability models and to compare it with EMTP simulations.« less

[The organizational characteristics of the medical support for the troops in the first operations at the start of a war (based on the experience of exercises)].

PubMed

Iziumtsev, I S

1995-03-01

The article summarized the experience of an explorative tactical-special exercise on medical support of Mobile Forces in first military operations of the initial period of war which has studied the following questions: the organic structure and organization of work of the medical service of a motorized infantry brigade in defense; joint direction of organic hospital facilities and field traumatological hospital. The author also studies the deployment peculiarities of a military multipurpose hospital on the basis of a garrison hospital. The experience of these exercises has proved the necessity to update the organic structure and principles of the employment of medical assets in accordance with the requirements of new military doctrine, as well as realize the technical re-equipment of medical service.

Fixation of operating point and measurement of turn on characteristics of IGBT F4-75R06W1E3

NASA Astrophysics Data System (ADS)

Haseena, A.; Subhash Joshi T., G.; George, Saly

2018-05-01

For the proficient operation of the Power electronic circuit, signal level performance of power electronic devices are very important. For getting good signal level characteristics, fixing operating point is very critical. Device deviates from the typical characteristics given in the datasheet due to the presence of stray components in the circuit lay out. Fixation of operating point of typical silicon IGBT and its turn on characteristics is discussed in this paper.

NASA Reactor Facility Hazards Summary. Volume 1

NASA Technical Reports Server (NTRS)

1959-01-01

The Lewis Research Center of the National Aeronautics and Space Administration proposes to build a nuclear research reactor which will be located in the Plum Brook Ordnance Works near Sandusky, Ohio. The purpose of this report is to inform the Advisory Committee on Reactor Safeguards of the U. S. Atomic Energy Commission in regard to the design Lq of the reactor facility, the characteristics of the site, and the hazards of operation at this location. The purpose of this research reactor is to make pumped loop studies of aircraft reactor fuel elements and other reactor components, radiation effects studies on aircraft reactor materials and equipment, shielding studies, and nuclear and solid state physics experiments. The reactor is light water cooled and moderated of the MTR-type with a primary beryllium reflector and a secondary water reflector. The core initially will be a 3 by 9 array of MTR-type fuel elements and is designed for operation up to a power of 60 megawatts. The reactor facility is described in general terms. This is followed by a discussion of the nuclear characteristics and performance of the reactor. Then details of the reactor control system are discussed. A summary of the site characteristics is then presented followed by a discussion of the larger type of experiments which may eventually be operated in this facility. The considerations for normal operation are concluded with a proposed method of handling fuel elements and radioactive wastes. The potential hazards involved with failures or malfunctions of this facility are considered in some detail. These are examined first from the standpoint of preventing them or minimizing their effects and second from the standpoint of what effect they might have on the reactor facility staff and the surrounding population. The most essential feature of the design for location at the proposed site is containment of the maximum credible accident.

Smooth time-dependent receiver operating characteristic curve estimators.

PubMed

Martínez-Camblor, Pablo; Pardo-Fernández, Juan Carlos

2018-03-01

The receiver operating characteristic curve is a popular graphical method often used to study the diagnostic capacity of continuous (bio)markers. When the considered outcome is a time-dependent variable, two main extensions have been proposed: the cumulative/dynamic receiver operating characteristic curve and the incident/dynamic receiver operating characteristic curve. In both cases, the main problem for developing appropriate estimators is the estimation of the joint distribution of the variables time-to-event and marker. As usual, different approximations lead to different estimators. In this article, the authors explore the use of a bivariate kernel density estimator which accounts for censored observations in the sample and produces smooth estimators of the time-dependent receiver operating characteristic curves. The performance of the resulting cumulative/dynamic and incident/dynamic receiver operating characteristic curves is studied by means of Monte Carlo simulations. Additionally, the influence of the choice of the required smoothing parameters is explored. Finally, two real-applications are considered. An R package is also provided as a complement to this article.

Concept of electro-optical sensor module for sniper detection system

NASA Astrophysics Data System (ADS)

Trzaskawka, Piotr; Dulski, Rafal; Kastek, Mariusz

2010-10-01

The paper presents an initial concept of the electro-optical sensor unit for sniper detection purposes. This unit, comprising of thermal and daylight cameras, can operate as a standalone device but its primary application is a multi-sensor sniper and shot detection system. Being a part of a larger system it should contribute to greater overall system efficiency and lower false alarm rate thanks to data and sensor fusion techniques. Additionally, it is expected to provide some pre-shot detection capabilities. Generally acoustic (or radar) systems used for shot detection offer only "after-the-shot" information and they cannot prevent enemy attack, which in case of a skilled sniper opponent usually means trouble. The passive imaging sensors presented in this paper, together with active systems detecting pointed optics, are capable of detecting specific shooter signatures or at least the presence of suspected objects in the vicinity. The proposed sensor unit use thermal camera as a primary sniper and shot detection tool. The basic camera parameters such as focal plane array size and type, focal length and aperture were chosen on the basis of assumed tactical characteristics of the system (mainly detection range) and current technology level. In order to provide costeffective solution the commercially available daylight camera modules and infrared focal plane arrays were tested, including fast cooled infrared array modules capable of 1000 fps image acquisition rate. The daylight camera operates as a support, providing corresponding visual image, easier to comprehend for a human operator. The initial assumptions concerning sensor operation were verified during laboratory and field test and some example shot recording sequences are presented.

Department of Defense (DOD) Automated Biometric Identification System (ABIS) Version 1.2: Initial Operational Test and Evaluation Report

DTIC Science & Technology

2015-05-01

Director, Operational Test and Evaluation Department of Defense (DOD) Automated Biometric Identification System (ABIS) Version 1.2 Initial...Operational Test and Evaluation Report May 2015 This report on the Department of Defense (DOD) Automated Biometric Identification System...COVERED - 4. TITLE AND SUBTITLE Department of Defense (DOD) Automated Biometric Identification System (ABIS) Version 1.2 Initial Operational Test

Electrolysis Performance Improvement Concept Study (EPICS) Flight Experiment-Reflight

NASA Technical Reports Server (NTRS)

Schubert, F. H.

1997-01-01

The Electrolysis Performance Improvement Concept Study (EPICS) is a flight experiment to demonstrate and validate in a microgravity environment the Static Feed Electrolyzer (SFE) concept which was selected for the use aboard the International Space Station (ISS) for oxygen (O2) generation. It also is to investigate the impact of microgravity on electrochemical cell performance. Electrochemical cells are important to the space program because they provide an efficient means of generating O2 and hydrogen (H2) in space. Oxygen and H2 are essential not only for the survival of humans in space but also for the efficient and economical operation of various space systems. Electrochemical cells can reduce the mass, volume and logistical penalties associated with resupply and storage by generating and/or consuming these gases in space. An initial flight of the EPICS was conducted aboard STS-69 from September 7 to 8, 1995. A temperature sensor characteristics shift and a missing line of software code resulted in only partial success of this initial flight. Based on the review and recommendations of a National Aeronautics and Space Administration (NASA) Johnson Space Center (JSC) review team a reflight activity was initiated to obtain the remaining desired results, not achieved during the initial flight.

Experimental study on a prototype of heat pipe solar water heater using refrigerant R134a as a transfer fluid

NASA Astrophysics Data System (ADS)

Sitepu, T.; Sembiring, J.; Ambarita, H.

2018-02-01

A prototype of a solar water heater by using refrigerant as a heat transfer fluid is investigated experimentally. The objective is to explore the characteristics and the performance of the prototype. To make heat transfer from the collector to the heated fluid effectively, refrigerant R134a is used as a transfer. In the experiments, the initial pressure inside the heat pipe is varied. The prototype is exposed to solar irradiation in a location in Medan city for three days of the experiment. Solar collector temperatures, solar radiation, water temperature, and ambient temperature are measured. The efficiency of the system is analyzed. The results show that temperature of the hot water increases as the initial pressure of the working fluid increase. However, the increasing is not linear, and there must exist an optimum initial pressure. For the case with the refrigerant pressure of 110 psi, the maximum hot water temperature and maximum thermal efficiency are 45.36oC and 53.23%, respectively. The main conclusion can be drawn here is that solar water heater by using refrigerant R134a should be operated at initial pressure 110 psi.

Concurrent airline fleet allocation and aircraft design with profit modeling for multiple airlines

NASA Astrophysics Data System (ADS)

Govindaraju, Parithi

A "System of Systems" (SoS) approach is particularly beneficial in analyzing complex large scale systems comprised of numerous independent systems -- each capable of independent operations in their own right -- that when brought in conjunction offer capabilities and performance beyond the constituents of the individual systems. The variable resource allocation problem is a type of SoS problem, which includes the allocation of "yet-to-be-designed" systems in addition to existing resources and systems. The methodology presented here expands upon earlier work that demonstrated a decomposition approach that sought to simultaneously design a new aircraft and allocate this new aircraft along with existing aircraft in an effort to meet passenger demand at minimum fleet level operating cost for a single airline. The result of this describes important characteristics of the new aircraft. The ticket price model developed and implemented here enables analysis of the system using profit maximization studies instead of cost minimization. A multiobjective problem formulation has been implemented to determine characteristics of a new aircraft that maximizes the profit of multiple airlines to recognize the fact that aircraft manufacturers sell their aircraft to multiple customers and seldom design aircraft customized to a single airline's operations. The route network characteristics of two simple airlines serve as the example problem for the initial studies. The resulting problem formulation is a mixed-integer nonlinear programming problem, which is typically difficult to solve. A sequential decomposition strategy is applied as a solution methodology by segregating the allocation (integer programming) and aircraft design (non-linear programming) subspaces. After solving a simple problem considering two airlines, the decomposition approach is then applied to two larger airline route networks representing actual airline operations in the year 2005. The decomposition strategy serves as a promising technique for future detailed analyses. Results from the profit maximization studies favor a smaller aircraft in terms of passenger capacity due to its higher yield generation capability on shorter routes while results from the cost minimization studies favor a larger aircraft due to its lower direct operating cost per seat mile.

Evaluating Urban Methane Emissions with a Light Rail Vehicle Platform in Salt Lake City, UT

NASA Astrophysics Data System (ADS)

Mitchell, L.; Fasoli, B.; Crosman, E.; Lin, J. C.; Bowling, D. R.; Ehleringer, J. R.

2016-12-01

Urban environments are characterized by both spatial complexity and temporal variability, each of which present challenges for measurement strategies aimed at constraining estimates of greenhouse gas emissions and air quality. To address these challenges we initiated a project in December 2014 to measure trace species (CO2, CH4, O3, and Particulate Matter) by way of a Utah Transit Authority (UTA) electricity-powered light rail vehicle whose route traverses the metropolitan Salt Lake Valley in Utah, USA on an hourly basis, retracing the same route through commercial, residential, suburban, and rural typologies. Light rail vehicles present advantages as a measurement platform, including the absence of in-situ fossil fuel emissions, regular repeated transects across an urban region that provide both spatial and temporal information, and relatively low operating costs. We will present initial results investigating methane point sources and evaluating the magnitude and temporal characteristics of these emissions.

Three-dimensional plotter technology for fabricating polymeric scaffolds with micro-grooved surfaces.

PubMed

Son, JoonGon; Kim, GeunHyung

2009-01-01

Various mechanical techniques have been used to fabricate biomedical scaffolds, including rapid prototyping (RP) devices that operate from CAD files of the target feature information. The three-dimensional (3-D) bio-plotter is one RP system that can produce design-based scaffolds with good mechanical properties for mimicking cartilage and bones. However, the scaffolds fabricated by RP have very smooth surfaces, which tend to discourage initial cell attachment. Initial cell attachment, migration, differentiation and proliferation are strongly dependent on the chemical and physical characteristics of the scaffold surface. In this study, we propose a new 3-D plotting method supplemented with a piezoelectric system for fabricating surface-modified scaffolds. The effects of the physically-modified surface on the mechanical and hydrophilic properties were investigated, and the results of cell culturing of chondrocytes indicate that this technique is a feasible new method for fabricating high-quality 3-D polymeric scaffolds.

The DAST-1 remotely piloted research vehicle development and initial flight testing

NASA Technical Reports Server (NTRS)

Kotsabasis, A.

1981-01-01

The development and initial flight testing of the DAST (drones for aerodynamic and structural testing) remotely piloted research vehicle, fitted with the first aeroelastic research wing ARW-I are presented. The ARW-I is a swept supercritical wing, designed to exhibit flutter within the vehicle's flight envelope. An active flutter suppression system (FSS) designed to increase the ARW-I flutter boundary speed by 20 percent is described. The development of the FSS was based on prediction techniques of structural and unsteady aerodynamic characteristics. A description of the supporting ground facilities and aircraft systems involved in the remotely piloted research vehicle (RPRV) flight test technique is given. The design, specification, and testing of the remotely augmented vehicle system are presented. A summary of the preflight and flight test procedures associated with the RPRV operation is given. An evaluation of the blue streak test flight and the first and second ARW-I test flights is presented.

Realizing "2001: A Space Odyssey": Piloted Spherical Torus Nuclear Fusion Propulsion

NASA Technical Reports Server (NTRS)

Williams, Craig H.; Dudzinski, Leonard A.; Borowski, Stanley K.; Juhasz, Albert J.

2005-01-01

A conceptual vehicle design enabling fast, piloted outer solar system travel was created predicated on a small aspect ratio spherical torus nuclear fusion reactor. The initial requirements were satisfied by the vehicle concept, which could deliver a 172 mt crew payload from Earth to Jupiter rendezvous in 118 days, with an initial mass in low Earth orbit of 1,690 mt. Engineering conceptual design, analysis, and assessment was performed on all major systems including artificial gravity payload, central truss, nuclear fusion reactor, power conversion, magnetic nozzle, fast wave plasma heating, tankage, fuel pellet injector, startup/re-start fission reactor and battery bank, refrigeration, reaction control, communications, mission design, and space operations. Detailed fusion reactor design included analysis of plasma characteristics, power balance/utilization, first wall, toroidal field coils, heat transfer, and neutron/x-ray radiation. Technical comparisons are made between the vehicle concept and the interplanetary spacecraft depicted in the motion picture 2001: A Space Odyssey.

Regulatory requirements for nuclear power plant site selection in Malaysia-a review.

PubMed

Basri, N A; Hashim, S; Ramli, A T; Bradley, D A; Hamzah, K

2016-12-01

Malaysia has initiated a range of pre-project activities in preparation for its planned nuclear power programme. Clearly one of the first steps is the selection of sites that are deemed suitable for the construction and operation of a nuclear power plant. Here we outline the Malaysian regulatory requirements for nuclear power plant site selection, emphasizing details of the selection procedures and site characteristics needed, with a clear focus on radiation safety and radiation protection in respect of the site surroundings. The Malaysia Atomic Energy Licensing Board (AELB) site selection guidelines are in accord with those provided in International Atomic Energy Agency (IAEA) and United Stated Nuclear Regulatory Commission (USNRC) documents. To enhance the suitability criteria during selection, as well as to assist in the final decision making process, possible assessments using the site selection characteristics and information are proposed.

Electro-optical properties of low viscosity driven holographic polymer dispersed liquid crystals

NASA Astrophysics Data System (ADS)

Moon, K. R.; Bae, S. Y.; Kim, B. K.

2015-04-01

Relative diffraction efficiency (RDE), operating voltage, and response times are most important performance characteristics of holographic polymer dispersed liquid crystals (HPDLC). Two types of triallyl isocyanurate (TI) having different structures were incorporated into the conventional transmission grating of HPDLC. Premix viscosity decreased by 13-18% with up to 3% TI, beyond which it increased. TI eliminated induction period and augmented initial grating formation rate at all contents. Saturation RDE increased over 200% while threshold voltage and rise time decreased to about half and 2/3, respectively up to 3% TI, beyond which the tendencies were reversed. Among the two TIs, low viscosity monomer (TA) showed high RDE, while high miscibility monomer (TE) low characteristic voltages and short response times. It is concluded that grating formation is largely favored by low viscosity, while interface tensions and electro-optical performances by miscibility at similar viscosities.

Perception of risk from automobile safety defects.

PubMed

Slovic, P; MacGregor, D; Kraus, N N

1987-10-01

Descriptions of safety engineering defects of the kind that compel automobile manufacturers to initiate a recall campaign were evaluated by individuals on a set of risk characteristic scales that included overall vehicle riskiness, manufacturer's ability to anticipate the defect, importance for vehicle operation, severity of consequences and likelihood of compliance with a recall notice. A factor analysis of the risk characteristics indicated that judgments could be summarized in terms of two composite scales, one representing the uncontrollability of the damage the safety defect might cause and the other representing the foreseeability of the defect by the manufacturer. Motor vehicle defects were found to be highly diverse in terms of the perceived qualities of their risks. Location of individual defects within the factor space was closely associated with perceived riskiness, perceived likelihood of purchasing another car from the same manufacturer, perceived likelihood of compliance with a recall notice, and actual compliance rates.

Development of high performance refractory fibers with enhanced insulating properties and longer service lifetimes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, P.C.; DePoorter, G.L.; Munoz, D.R.

1991-02-01

We have initiated a three phase investigation of the development of high performance refractory fibers with enhanced insulating properties and longer usable lifetimes. This report presents the results of the first phase of the study, performed from Aug. 1989 through Feb. 1991, which shows that significant energy saving are possible through the use of high temperature insulating fibers that better retain their efficient insulating properties during the service lifetime of the fibers. The remaining phases of this program include the pilot scale development and then full scale production feasibility development and evaluation of enhanced high temperature refractory insulting fibers. Thismore » first proof of principle phase of the program presents a summary of the current use patterns of refractory fibers, a laboratory evaluation of the high temperature performance characteristics of selected typical refractory fibers and an analysis of the potential energy savings through the use of enhanced refractory fibers. The current use patterns of refractory fibers span a wide range of industries and high temperature furnaces within those industries. The majority of high temperature fiber applications are in furnaces operating between 2000 and 26000{degrees}F. The fibers used in furnaces operating within this range provide attractive thermal resistance and low thermal storage at reasonable cost. A series of heat treatment studies performed for this phase of the program has shown that the refractory fibers, as initially manufactured, have attractive thermal conductivities for high temperature applications but the fibers go through rapid devitrification and subsequent crystal growth upon high temperature exposure. Development of improved fibers, maintaining the favorable characteristics of the existing as-manufactured fibers, could save between 1 and 4% of the energy consumed in high temperature furnaces using refractory fibers.« less

[Penis-preserving surgery in patients with primary penile urethral cancer].

PubMed

Maek, M; Musch, M; Arnold, G; Kröpfl, D

2014-12-01

Primary urethral cancer in males is a rare entity with only approximately 800 cases described, which is why it is difficult to formulate evidence-based guidelines for treatment. For tumors in the pT2 stage with a localization distal to the membranous urethra, a penis-preserving operation can be carried out. In the period from November 2006 to February 2014 a total of 4 patients with primary urethral cancer underwent a penis-preserving urethral resection. The tumor characteristics and treatment results were collated retrospectively. Of the four patients one had a transitional cell carcinoma of the mid-penile urethra in stage pT2 G2. In two out of the four patients a squamous cell carcinoma (PEC) was present in the mid-penile urethra in stages pT2 G2 and pT2 G3, respectively, with concomitant carcinoma in situ (CIS). The fourth patient had a PEC of the fossa terminalis in stage pT2 G2. Initially all patients underwent a penis-preserving resection. In one case, despite an initial R0 resection a local recurrence occurred and a complete penectomy was performed. Irradiation and lymphadenectomy were not carried out. At a mean follow-up of 37 months all patients are currently in complete remission. Primary penile urethral cancer can be treated by a penis-preserving operation. Close follow-up is essential because recurrence can arise despite an initial R0 resection.

Improving OBS operations in ultra-deep ocean during the Southern Mariana Trench expeditions

NASA Astrophysics Data System (ADS)

Zeng, X.; Lin, J.; Xu, M.; Zhou, Z.

2017-12-01

The Mariana Trench Research Initiative, led by the South China Sea Institute of Oceanology of the Chinese Academy of Sciences and through international collaboration, focuses on investigating the deep and shallow lithospheric structure, earthquake characteristics, extreme geological environments, and the controlling geodynamic mechanisms for the formation of Earth's deepest basins in the southern Mariana Trench. Two multidisciplinary research expeditions were executed during December 2016 and June 2017, respectively, on board R/V Shiyan 3. A main task of the Mariana Initiative is to conduct the Southern Mariana OBS Experiment (SMOE), the first OBS seismic experiment across the Challenger Deep. The SMOE expeditions include both active and passive source seismic experiments and employed a large number of broadband OBS instruments. Due to the deep water, rough weather, strong winds, and other unfavorable factors, it was challenging to deploy/recover the OBSs. During the two expeditions we developed and experimented with a number of ways to improve the success rate of OBS operations in the harsh ultra-deep ocean environment of the Southern Mariana Trench. All newly acquired OBSs underwent a series of uniquely designed deep-ocean tests to improve the instrument performance and maximize reliability during their deployment under the ultra-high pressure conditions. The OBS deployment and recovery followed a unified standard operation procedure and aided by an instrumental checklist, which were specifically designed and strictly enforced for operation during the expeditions. Furthermore, an advanced ship-based radio positioning system was developed to rapidly and accurately locate the OBS instruments when they reached the sea surface; the system proved its effectiveness even under extreme weather conditions. Through the development and application of the novel methods for operation in deep oceans, we overcame the rough sea and other unfavorable factors during the first two expeditions to the southern Mariana Trench and achieved a highly successful OBS operation program.

Initial Experimental Airworthiness Certification Guidance for UAS. UAS Experimental Certification Process and Guidance

NASA Technical Reports Server (NTRS)

2005-01-01

This paper addresses the regulatory processes and requirements already in place by which an applicant might obtain experimental airworthiness certification for a civil Unmanned Aircraft System (UAS). It is more extensive and subsequent to an earlier, similar deliverable, PD007, which was an interim study of the same topic. Since few regulatory airworthiness and operating standards exist for UAS like those for traditional manned aircraft and since most UAS have historically been developed and operated under military auspices, civil use of UAS in the NAS is a new and unfamiliar challenge requiring specific and unique considerations. Experimental certification is the most basic level of FAA approval toward routine UAS operation in the NAS. The paper reviews and explains existing FAA requirements for an applicant seeking experimental airworthiness approval and details the process for submission of necessary information. It summarizes the limited purposes for which experimental aircraft may be used and addresses pertinent aspects of UAS design, construction and operation in the NAS in harmony with traditional manned aircraft. Policy IPT position is that UAS, while different from manned aircraft, can use the same initial processes to gain civil operating experience under the experimental approval. Particular note is taken of those UAS-unique characteristics which require extra attention to assure equivalent safety of operation, such as the UAS control station and sense-and-avoid. The paper also provides "best practices" guidance for UAS manufacturers and FAA personnel in two appendices. The material in Appendix A is intended to provide guidance on assuring UAS safety to FAA, and provides FAA personnel with a suggested list of items to review, with a focus on UAS unique factors, prior to issuance of an experimental airworthiness certificate. Appendix B provides an outline for a program letter which a manufacturer could use in preparing the application for an UAS experimental airworthiness certificate.

Design and Field Test of a Mass Efficient Crane for Lunar Payload Handling and Inspection: The Lunar Surface Manipulation System

NASA Technical Reports Server (NTRS)

Doggett, William R.; King, Bruce D.; Jones, Thomas Carno; Dorsey, John T.; Mikulas, Martin M.

2008-01-01

Devices for lifting, translating and precisely placing payloads are critical for efficient Earthbased construction operations. Both recent and past studies have demonstrated that devices with similar functionality will be needed to support lunar outpost operations. Lunar payloads include: a) prepackaged hardware and supplies which must be unloaded from landers and then accurately located at their operational site, b) sensor packages used for periodic inspection of landers, habitat surfaces, etc., and c) local materials such as regolith which require grading, excavation and placement. Although several designs have been developed for Earth based applications, these devices lack unique design characteristics necessary for transport to and use on the harsh lunar surface. These design characteristics include: a) composite components, b) compact packaging for launch, c) simple in-field reconfiguration and repair, and d) support for tele-operated or automated operations. Also, in contrast to Earth-based construction, where special purpose devices dominate a construction site, a lunar outpost will require versatile devices which provide operational benefit from initial construction through sustained operations. This paper will detail the design of a unique, high performance, versatile lifting device designed for operations on the lunar surface. The device is called the Lunar Surface Manipulation System to highlight the versatile nature of the device which supports conventional cable suspended crane operations as well as operations usually associated with a manipulator such as precise positioning where the payload is rigidly grappled by a tool attached to the tip of the device. A first generation test-bed to verify design methods and operational procedures is under development at the NASA Langley Research Center and recently completed field tests at Moses Lake Washington. The design relied on non-linear finite element analysis which is shown to correlate favorably with laboratory experiments. A key design objective, reviewed in this paper, is the device s simplicity, resulting from a focus on the minimum set of functions necessary to perform payload offload. Further development of the device has the potential for significant mass savings, with a high performance device incorporating composite elements estimated to have a mass less than 3% of the mass of the maximum lunar payload lifted at the tip. The paper will conclude with future plans for expanding the operational versatility of the device.

Risk Stratification for the Development of Respiratory Adverse Events Following Vascular Surgery Using the Society of Vascular Surgery’s Vascular Quality Initiative

PubMed Central

Genovese, Elizabeth A; Fish, Larry; Chaer, Rabih A; Makaroun, Michel S; Baril, Donald T

2017-01-01

Objective Post-operative respiratory adverse events (RAEs) are associated with high rates of morbidity and mortality in general surgery, however little is known about these complications in the vascular surgery population, a frail subset with multiple comorbidities. The objective of this study was to describe the contemporary incidence of RAEs in vascular surgery patients, the risk factors for this complication and the overall impact of RAEs on patient outcomes. Methods The Vascular Quality Initiative was queried (2003–2014) for patients who underwent endovascular abdominal aortic repair, open abdominal aortic aneurysm (AAA) repair, thoracic endovascular aortic repair (TEVAR), suprainguinal bypass or infrainguinal bypass. A mixed-effects logistic regression model determined the independent risk factors for RAEs. Using a random 85% of the cohort, a risk prediction score for RAEs was created and the score was validated using the remaining 15% of the cohort, comparing the predicted to the actual incidence of RAE and determining the area under the receiver operating characteristic curve. The independent risk of in-hospital mortality and discharge to a nursing facility associated with RAEs was determined using a mixed-effects logistic regression to control for baseline patient characteristics, operative variables and other post-operative adverse events. Results The cohort consisted of 52,562 patients, with a 5.4% incidence of RAEs. The highest rates of RAEs were seen in current smokers (6.1%), recent acute myocardial infarction (10.1%), symptomatic congestive heart failure (CHF) (9.9%), chronic obstructive pulmonary disease (COPD) requiring oxygen therapy (11.0%), urgent and emergent procedures (6.4% and 25.9%, respectively), open AAA repairs (17.6%), in-situ suprainguinal bypasses (9.68%) and TEVARs (9.6%). The variables included in the risk prediction score were age, body mass index, smoking status, CHF severity, COPD severity, degree of renal insufficiency, ambulatory status, transfer status, urgency and operative type. The predicted compared to the actual RAE incidence were highly correlated, with a correlation coefficient of 0.943 (P<.0001) and a c-statistic=0.818. RAEs had a significantly higher rates of in-hospital mortality (25.4% vs. 1.2%, P<.0001, adjusted OR=5.85, P<.0001) and discharge to a nursing facility (57.8% vs. 19.0%, P<.0001, adjusted OR=3.14, P<.0001). Conclusions RAEs are frequent and one of the strongest risk factors for in-hospital mortality and inability to be discharged home. Our risk prediction score accurately stratifies patients based on key demographics, comorbidities, presentation, and operative type that can be used to guide patient counseling, preoperative optimization, and post-operative management. Furthermore, it may be useful in developing quality benchmarks for RAE following major vascular surgery. PMID:27832989

A high-order Lagrangian-decoupling method for the incompressible Navier-Stokes equations

NASA Technical Reports Server (NTRS)

Ho, Lee-Wing; Maday, Yvon; Patera, Anthony T.; Ronquist, Einar M.

1989-01-01

A high-order Lagrangian-decoupling method is presented for the unsteady convection-diffusion and incompressible Navier-Stokes equations. The method is based upon: (1) Lagrangian variational forms that reduce the convection-diffusion equation to a symmetric initial value problem; (2) implicit high-order backward-differentiation finite-difference schemes for integration along characteristics; (3) finite element or spectral element spatial discretizations; and (4) mesh-invariance procedures and high-order explicit time-stepping schemes for deducing function values at convected space-time points. The method improves upon previous finite element characteristic methods through the systematic and efficient extension to high order accuracy, and the introduction of a simple structure-preserving characteristic-foot calculation procedure which is readily implemented on modern architectures. The new method is significantly more efficient than explicit-convection schemes for the Navier-Stokes equations due to the decoupling of the convection and Stokes operators and the attendant increase in temporal stability. Numerous numerical examples are given for the convection-diffusion and Navier-Stokes equations for the particular case of a spectral element spatial discretization.

Towards autonomous fuzzy control

NASA Technical Reports Server (NTRS)

Shenoi, Sujeet; Ramer, Arthur

1993-01-01

The efficient implementation of on-line adaptation in real time is an important research problem in fuzzy control. The goal is to develop autonomous self-organizing controllers employing system-independent control meta-knowledge which enables them to adjust their control policies depending on the systems they control and the environments in which they operate. An autonomous fuzzy controller would continuously observe system behavior while implementing its control actions and would use the outcomes of these actions to refine its control policy. It could be designed to lie dormant when its control actions give rise to adequate performance characteristics but could rapidly and autonomously initiate real-time adaptation whenever its performance degrades. Such an autonomous fuzzy controller would have immense practical value. It could accommodate individual variations in system characteristics and also compensate for degradations in system characteristics caused by wear and tear. It could also potentially deal with black-box systems and control scenarios. On-going research in autonomous fuzzy control is reported. The ultimate research objective is to develop robust and relatively inexpensive autonomous fuzzy control hardware suitable for use in real time environments.

Propulsion Study for Small Transport Aircraft Technology (STAT)

NASA Technical Reports Server (NTRS)

Gill, J. C.; Earle, R. V.; Staton, D. V.; Stolp, P. C.; Huelster, D. S.; Zolezzi, B. A.

1980-01-01

Propulsion requirements were determined for 0.5 and 0.7 Mach aircraft. Sensitivity studies were conducted on both these aircraft to determine parametrically the influence of propulsion characteristics on aircraft size and direct operating cost (DOC). Candidate technology elements and design features were identified and parametric studies conducted to select the STAT advanced engine cycle. Trade off studies were conducted to determine those advanced technologies and design features that would offer a reduction in DOC for operation of the STAT engines. These features were incorporated in the two STAT engines. A benefit assessment was conducted comparing the STAT engines to current technology engines of the same power and to 1985 derivatives of the current technology engines. Research and development programs were recommended as part of an overall technology development plan to ensure that full commercial development of the STAT engines could be initiated in 1988.

Regression analysis of traction characteristics of traction fluids

NASA Technical Reports Server (NTRS)

Loewenthal, S. H.; Rohn, D. A.

1983-01-01

Traction data for Santotrac 50 and TDF-88 over a wide range of operating conditions were analyzed. An eight term correlation equation to predict the maximum traction coefficient and a six term correlation equation to predict the initial slope of the traction curve were developed. The slope correlation was corrected for size effect considering the compliance of the disks. The effects of different operating conditions on the traction performance of each traction fluid were studied. Both fluids exhibited a loss in traction with increases in spin, but the losses with the TDF-88 fluid were not as severe as those with Santotrac 50. Overall, both fluids exhibited similar performance, showing an increase in traction with contact pressure up to about 2.0 GPa, and a reduction in traction with higher surface speeds up to about 100 m/sec. The apparent stiffness of the traction contact, that is, film disk combination, increases with contact pressure and decreases with speed.

A study to define the research and technology requirements for advanced turbo/propfan transport aircraft

NASA Technical Reports Server (NTRS)

Goldsmith, I. M.

1981-01-01

The feasibility of the propfan relative to the turbofan is summarized, using the Douglas DC-9 Super 80 (DS-8000) as the actual operational base aircraft. The 155 passenger economy class aircraft (31,775 lb 14,413 kg payload), cruise Mach at 0.80 at 31,000 ft (8,450 m) initial altitude, and an operational capability in 1985 was considered. Three propfan arrangements, wing mounted, conventional horizontal tail aft mounted, and aft fuselage pylon mounted are selected for comparison with the DC-9 Super 80 P&WA JT8D-209 turbofan powered aircraft. The configuration feasibility, aerodynamics, propulsion, structural loads, structural dynamics, sonic fatigue, acoustics, weight maintainability, performance, rough order of magnitude economics, and airline coordination are examined. The effects of alternate cruise Mach number, mission stage lengths, and propfan design characteristics are considered. Recommendations for further study, ground testing, and flight testing are included.

Space station needs, attributes, and architectural options: Commercial opportunities in space

NASA Technical Reports Server (NTRS)

Wolbers, H. L., Jr.

1983-01-01

The roles of government and industry in the commercialization of space are examined and an approach for stimulating the interests of potential users is described. Several illustrative examples of potential commercial developments are presented. The role of manned space systems in space commercialization is discussed as well as some of the issues and opportunities that are likely to be encountered in the commercial exploitation of the unique characteristics of space. Results suggest that interest in space facilities can be found among a number of commercially oriented users. In order to develop and maintain the involvement of these potential users, however, space demonstrations are required, and commercial growth or evolution depends on the results of the initial in situ experience. Manned facilities are required for the conceptual research and development phases and for maintenance and servicing operations during production or operational missions. Space facilities must be easily accessible by dependable and regularly scheduled means.

Cascadia Initiative Ocean Bottom Seismograph Performance

NASA Astrophysics Data System (ADS)

Evers, B.; Aderhold, K.

2017-12-01

The Ocean Bottom Seismograph Instrument Pool (OBSIP) provided instrumentation and operations support for the Cascadia Initiative community experiment. This experiment investigated geophysical processes across the Cascadia subduction zone through a combination of onshore and offshore seismic data. The recovery of Year 4 instruments in September 2015 marked the conclusion of a multi-year experiment that utilized 60 ocean-bottom seismographs (OBSs) specifically designed for the subduction zone boundary, including shallow/deep water deployments and active fisheries. The new instruments featured trawl-resistant enclosures designed by Lamont-Doherty Earth Observatory (LDEO) and Scripps Institution of Oceanography (SIO) for shallow deployment [water depth ≤ 500 m], as well as new deep-water instruments designed by Woods Hole Oceanographic Institute (WHOI). Existing OBSIP instruments were also deployed along the Blanco Transform Fault and on the Gorda Plate through complementary experiments. Station instrumentation included weak and strong motion seismometers, differential pressure gauges (DPG) and absolute pressure gauges (APG). All data collected from the Cascadia, Blanco, and Gorda deployments is available through the Incorporated Research Institutions for Seismology (IRIS) Data Management Center (DMC). The Cascadia Initiative is the largest amphibious seismic experiment undertaken to date, encompassing a diverse technical implementation and demonstrating an effective structure for community experiments. Thus, the results from Cascadia serve as both a technical and operational resource for the development of future community experiments, such as might be contemplated as part of the SZ4D Initiative. To guide future efforts, we investigate and summarize the quality of the Cascadia OBS data using basic metrics such as instrument recovery and more advanced metrics such as noise characteristics through power spectral density analysis. We also use this broad and diverse deployment to explore other environmental and configuration factors that can impact sensor and network performance and inform the design of future deployments.

Operation of staged membrane oxidation reactor systems

DOEpatents

Repasky, John Michael

2012-10-16

A method of operating a multi-stage ion transport membrane oxidation system. The method comprises providing a multi-stage ion transport membrane oxidation system with at least a first membrane oxidation stage and a second membrane oxidation stage, operating the ion transport membrane oxidation system at operating conditions including a characteristic temperature of the first membrane oxidation stage and a characteristic temperature of the second membrane oxidation stage; and controlling the production capacity and/or the product quality by changing the characteristic temperature of the first membrane oxidation stage and/or changing the characteristic temperature of the second membrane oxidation stage.

Suppression of Instability of High Pressure DC Microplasma Operating in the Negative Differential Resistance (NDR) Regime

NASA Astrophysics Data System (ADS)

Mahamud, Rajib; Farouk, Tanvir I.

2015-09-01

Microplasma devices have been the subject of considerable interest and research during the last decade. In a DC system most of the operation regime of the plasma discharges studied fall in the ``abnormal,'' ``normal'' and ``corona'' modes - where a quasi-steady state is achieved. It is well known that even in a DC system the negative differential resistance (NDR) regime can trigger self pulsing discharges. These pulsations are initiated by the parasitic capacitance of the system hence governed by the response time of the power circuit. The circuit response time is required to be larger than the ion transit time to initiate the oscillations. In this present study a suppressor circuit element in the form of an inductor is used to restrain the plasma from switching to a self pulsing mode. It has been identified that the combined response time of the inductor and the plasma discharge (L/Rplasma) has to be larger than the power circuit time constant (RC) to achieve suppression. Inhibition of oscillation has been observed in both experiments and numerical simulations. The obtained voltage-current characteristics show that the inductor element extends the normal glow regime to lower current. Additional parametric simulations are conducted to map out a ``stable'' operation regime. The author would like to thank DARPA (ARO Grant No. W911NF1210007) and University of South Carolina (USC) for the financial support of the work.

Characteristics of Subfreezing Operation of Polymer Electrolyte Membrane Fuel Cells

NASA Astrophysics Data System (ADS)

Mishler, Jeffrey Harris

Polymer Electrolyte Membrane (PEM) Fuel Cells are capable of high efficiency operation, and are free of NOx, SOx, and CO2 emissions when using hydrogen fuel, and ideally suited for use in transportation applications due to their high power density and low operating temperatures. However, under subfreezing conditions which may be encountered during winter seasons in some areas, product water will freeze within the membrane, cathode side catalyst layer and gas diffusion media, leading to voltage loss and operation failure. Experiments were undertaken in order to characterize the amount and location of water during fuel cell operation. First, in-situ neutron radiography was undertaken on the fuel cells at a normal operating temperature for various operating current densities, inlet relative humidities, and diffusion media hydrophobicities. It was found that more hydrophobic cathode microporous layer (MPL) or hydrophilic anode MPL may result in a larger amount of water transporting back to the anode. The water profiles along the channels were measured and the point of liquid water emergence, where two phase flow begins, was compared to previous models. Secondly, under subfreezing temperatures, neutron imaging showed that water ice product accumulates because of lack of a water removal mechanism. Water was observed under both the lands and channels, and increased almost linearly with time. It is found that most ice exists in the cathode side. With evidence from experimental observation, a cold start model was developed and explained, following existing approaches in the literature. Three stages of cold start are explained: membrane saturation, ice storage in catalyst layer pores, and then ice melting. The voltage losses due to temperature change, increased transport resistance, and reduced electrochemical surface area. The ionic conductivity of the membrane at subfreezing temperatures was modeled. Voltage evolution over time for isothermal cold starts was predicted and validated against experimental data. The ice coverage coefficient was shown to be a key variable in matching with experimental data. From model analysis, it appears that the coulombs of charge passed before operation failure is an important parameter characterizing PEM fuel cell cold start. To investigate the coulombs of charge and its determining factors, PEM fuel cells were constructed to measure the effects of membrane configuration (thickness and initial state), catalyst layer configuration (thickness and ionomer-carbon ratio), current density, and temperature on the quantity. It was found that subfreezing temperature, ionomer-catalyst ratio, and catalyst-layer thickness significantly affect the amount of charge transferred before operational failure, whereas the membrane thickness and initial hydration level have limited effect for the considered cases. In addition, degradation of the catalyst layer was observed and quantified. These results improve the fundamental understanding of characteristics of subfreezing operation and thus are valuable for automobile applications of PEM fuel cells. The model directly relates the material properties to voltage loss, and predicts voltage evolution, thus providing a way for material optimization and diagnostics. Additionally, insights into component design and operating conditions can be used to better optimize the fuel cell for cold start-up of the vehicle.

Operational Characteristics of an Accelerator Driven Fissile Solution System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kimpland, Robert Herbert

Operational characteristics represent the set of responses that a nuclear system exhibits during normal operation. Operators rely on this behavior to assess the status of the system and to predict the consequences of off-normal events. These characteristics largely refer to the relationship between power and system operating conditions. The static and dynamic behavior of a chain-reacting system, operating at sufficient power, is primarily governed by reactivity effects. The science of reactor physics has identified and evaluated a number of such effects, including Doppler broadening and shifts in the thermal neutron spectrum. Often these reactivity effects are quantified in the formmore » of feedback coefficients that serve as coupling coefficients relating the neutron population and the physical mechanisms that drive reactivity effects, such as fissile material temperature and density changes. The operational characteristics of such nuclear systems usually manifest themselves when perturbations between system power (neutron population) and system operating conditions arise. Successful operation of such systems requires the establishment of steady equilibrium conditions. However, prior to obtaining the desired equilibrium (steady-state) conditions, an approach from zero-power (startup) must occur. This operational regime may possess certain limiting system conditions that must be maintained to achieve effective startup. Once steady-state is achieved, a key characteristic of this operational regime is the level of stability that the system possesses. Finally, a third operational regime, shutdown, may also possess limiting conditions of operation that must be maintained. This report documents the operational characteristics of a “generic” Accelerator Driven Fissile Solution (ADFS) system during the various operational regimes of startup, steady-state operation, and shutdown. Typical time-dependent behavior for each operational regime will be illustrated, and key system parameters, such as response times, will be quantified. A generalized linear systems analysis of steady-state operations will be performed to evaluate the level of stability of ADFS systems. This information should provide a basic understanding of typical ADFS system operational behavior, and facilitate the development of monitoring procedures and operator aids.« less

Fuel-conservative guidance system for powered-lift aircraft

NASA Technical Reports Server (NTRS)

Erzberger, H.; Mclean, J. D.

1979-01-01

A concept for automatic terminal area guidance, comprising two modes of operation, was developed and evaluated in flight tests. In the predictive mode, fuel efficient approach trajectories are synthesized in fast time. In the tracking mode, the synthesized trajectories are reconstructed and tracked automatically. An energy rate performance model derived from the lift, drag, and propulsion system characteristics of the aircraft is used in the synthesis algorithm. The method optimizes the trajectory for the initial aircraft position and wind and temperature profiles encountered during each landing approach. The design theory and the results of simulations and flight tests using the Augmentor Wing Jet STOL Research Aircraft are described.

IRE1: ER stress sensor and cell fate executor

PubMed Central

Chen, Yani; Brandizzi, Federica

2013-01-01

Cells operate a signaling network termed unfolded protein response (UPR) to monitor protein-folding capacity in the endoplasmic reticulum (ER). IRE1 is an ER transmembrane sensor that activates UPR to maintain ER and cellular function. While mammalian IRE1 promotes cell survive, it can initiate apoptosis via decay of anti-apoptotic microRNAs. Convergent and divergent IRE1 characteristics between plants and animals underscore its significance in cellular homeostasis. This review provides an updated scenario of IRE1 signaling model, discusses emerging IRE1 sensing mechanisms, compares IRE1 features among species, and outlines exciting future directions in UPR research. PMID:23880584

Effect of ambient temperature and humidity on emissions of an idling gas turbine

NASA Technical Reports Server (NTRS)

Kauffman, C. W.

1977-01-01

The effects of inlet pressure, temperature, and humidity on the oxides of nitrogen produced by an engine operating at takeoff power setting were investigated and numerous correction factors were formulated. The effect of ambient relative humidity on gas turbine idle emissions was ascertained. Experimentally, a nonvitiating combustor rig was employed to simulate changing combustor inlet conditions as generated by changing ambient conditions. Emissions measurements were made at the combustor exit. For carbon monoxide, a reaction kinetic scheme was applied within each zone of the combustor where initial species concentrations reflected not only local combustor characteristics but also changing ambient conditions.

Commercialization of biomass projects: A case study of the design, development, and application of a biomass gasifier to a large retrofit market

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woerner, W.L.

1994-12-31

The steam production potential of older biomass-fired boilers currently in operation may be significantly increased through the application of a commercially available gasifier. A large percentage of boiler systems in lumber mills and similar applications were initially designed to generate steam through convection heat transfer, and have been horse power rated at approximately 7 to 10 square feet of heating surface to the horse power. This paper deals with the before and after performance characteristics of the first gasifier retrofit installation based on an AED designed unit currently commercially available.

European X-ray observatory satellite (Exosat)

NASA Technical Reports Server (NTRS)

1983-01-01

Initially planned to be launched on the Ariane L6, the 510 kilogram European X-Ray Observatory Satellite (EXOSAT) is to be placed into orbit from Space Launch Complex 2 West by NASA's Delta 3914 launch vehicle. Objectives of the mission are to study the precise position, structure, and temporal and spectral characteristics of known X-ray sources as well as search for new sources. The spacecraft is described as well as its payload, principal subsystems, and the stages of the Delta 3914. The flight sequence of events, land launch operations are discussed. The ESA management structure for EXOSAT, the NASA/industry team, and contractors are listed.

Line-scan system for continuous hand authentication

NASA Astrophysics Data System (ADS)

Liu, Xiaofeng; Kong, Lingsheng; Diao, Zhihui; Jia, Ping

2017-03-01

An increasing number of heavy machinery and vehicles have come into service, giving rise to a significant concern over protecting these high-security systems from misuse. Conventionally, authentication performed merely at the initial login may not be sufficient for detecting intruders throughout the operating session. To address this critical security flaw, a line-scan continuous hand authentication system with the appearance of an operating rod is proposed. Given that the operating rod is occupied throughout the operating period, it can be a possible solution for unobtrusively recording the personal characteristics for continuous monitoring. The ergonomics in the physiological and psychological aspects are fully considered. Under the shape constraints, a highly integrated line-scan sensor, a controller unit, and a gear motor with encoder are utilized. This system is suitable for both the desktop and embedded platforms with a universal serial bus interface. The volume of the proposed system is smaller than 15% of current multispectral area-based camera systems. Based on experiments on a database with 4000 images from 200 volunteers, a competitive equal error rate of 0.1179% is achieved, which is far more accurate than the state-of-the-art continuous authentication systems using other modalities.

Space Mechanisms Lessons Learned and Accelerated Testing Studies

NASA Technical Reports Server (NTRS)

Fusaro, Robert L.

1997-01-01

A number of mechanism (mechanical moving component) failures and anomalies have recently occurred on satellites. In addition, more demanding operating and life requirements have caused mechanism failures or anomalies to occur even before some satellites were launched (e.g., during the qualification testing of GOES-NEXT, CERES, and the Space Station Freedom Beta Joint Gimbal). For these reasons, it is imperative to determine which mechanisms worked in the past and which have failed so that the best selection of mechanically moving components can be made for future satellites. It is also important to know where the problem areas are so that timely decisions can be made on the initiation of research to develop future needed technology. To chronicle the life and performance characteristics of mechanisms operating in a space environment, a Space Mechanisms Lessons Learned Study was conducted. The work was conducted by the NASA Lewis Research Center and by Mechanical Technologies Inc. (MTI) under contract NAS3-27086. The expectation of the study was to capture and retrieve information relating to the life and performance of mechanisms operating in the space environment to determine what components had operated successfully and what components had produced anomalies.

40 CFR 63.4151 - How do I demonstrate initial compliance with the emission limitations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... without add-on controls option for any individual coating operation, for any group of coating operations in the affected source, or for all of the coating operations in the affected source. You must use... operation(s) in the affected source for which you do not use this option. To demonstrate initial compliance...

Utility of MRCP in clinical decision making of suspected choledocholithiasis: An institutional analysis and literature review.

PubMed

Badger, Wesley R; Borgert, Andrew J; Kallies, Kara J; Kothari, Shanu N

2017-08-01

The ideal treatment algorithm for suspected choledocholithiasis is not yet well defined. Imaging options include magnetic resonance cholangiopancreatography (MRCP), endoscopic retrograde cholangiopancreatography (ERCP), and intraoperative cholangiogram (IOC). MRCP is diagnostic, while the other two modalities can also be therapeutic. Each of these modalities for diagnosis and treatment carries its own set of risks, benefits, and institutional costs. We hypothesized that there would be a significant difference between the biochemical profiles and characteristics of patients who undergo ERCP vs. MRCP vs. operative intervention as the initial choice of treatment/imaging modality. We performed a retrospective review of the electronic medical records for all patients with a coded diagnosis of choledocholithiasis from 2011 to 2014. The initial diagnostic modality was assessed for each hospital encounter. The statistical characteristics of MRCP as compared to fluoroscopic imaging of the biliary tree (ERCP, IOC) were analyzed. Overall, 527 hospital encounters were identified. Initial intervention included ERCP in 63%, MRCP in 12%, and cholecystectomy in 25% of patients. Patients undergoing cholecystectomy first, compared to MRCP or ERCP, tended to have lower values for alkaline phosphatase (P < 0.001) and AST (P = 0.002) as well as be of younger age (P < 0.0001). Of the patients that underwent MRCP as their initial procedure, 82% subsequently underwent either ERCP or laparoscopic cholecystectomy. In patients who underwent an initial MRCP followed by either ERCP or IOC, the predictive performance of MRCP was as follows: sensitivity = 0.90, specificity = 0.86, positive predictive value = 0.97, negative predictive value = 0.60, agreement (Cohen's Kappa) = 0.64. There is a significant difference in the laboratory evaluation and demographics of patients undergoing ERCP, MRCP, and laparoscopic cholecystectomy. MRCP was followed with a more invasive test a majority of the time. Since MRCP did not change the management of patients with suspected choledocholithiasis, its utility in this patient population should be questioned. Further research is needed to better define the pretest characteristics which would predict which patients do not need further intervention after MRCP as well as defining the most cost-effective strategy. Copyright © 2016 Elsevier Inc. All rights reserved.

14 CFR 23.253 - High speed characteristics.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false High speed characteristics. 23.253 Section... Requirements § 23.253 High speed characteristics. If a maximum operating speed VMO/MMO is established under § 23.1505(c), the following speed increase and recovery characteristics must be met: (a) Operating...

14 CFR 23.253 - High speed characteristics.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false High speed characteristics. 23.253 Section... Requirements § 23.253 High speed characteristics. If a maximum operating speed VMO/MMO is established under § 23.1505(c), the following speed increase and recovery characteristics must be met: (a) Operating...

Multidisciplinary team simulation for the operating theatre: a review of the literature.

PubMed

Tan, Shaw Boon; Pena, Guilherme; Altree, Meryl; Maddern, Guy J

2014-01-01

Analyses of adverse events inside the operating theatre has demonstrated that many errors are caused by failure in non-technical skills and teamwork. While simulation has been used successfully for teaching and improving technical skills, more recently, multidisciplinary simulation has been used for training team skills. We hypothesized that this type of training is feasible and improves team skills in the operating theatre. A systematic search of the literature for studies describing true multidisciplinary operating theatre team simulation was conducted in November and December 2012. We looked at the characteristics and outcomes of the team simulation programmes. 1636 articles were initially retrieved. Utilizing a stepwise evaluation process, 26 articles were included in the review. The studies reveal that multidisciplinary operating theatre simulation has been used to provide training in technical and non-technical skills, to help implement new techniques and technologies, and to identify latent weaknesses within a health system. Most of the studies included are descriptions of training programmes with a low level of evidence. No randomized control trial was identified. Participants' reactions to the training programme were positive in all studies; however, none of them could objectively demonstrate that skills acquired from simulation are transferred to the operating theatre or show a demonstrable benefit in patient outcomes. Multidisciplinary operating room team simulation is feasible and widely accepted by participants. More studies are required to assess the impact of this type of training on operative performance and patient safety. © 2013 Royal Australasian College of Surgeons.

Virtual touch tissue quantification using acoustic radiation force impulse technology: initial clinical experience with solid breast masses.

PubMed

Bai, Min; Du, Lianfang; Gu, Jiying; Li, Fan; Jia, Xiao

2012-02-01

The purpose of this study was to investigate the clinical usage of Virtual Touch tissue quantification (VTQ; Siemens Medical Solutions, Mountain View, CA) implementing sonographic acoustic radiation force impulse technology for differentiation between benign and malignant solid breast masses. A total of 143 solid breast masses were examined with VTQ, and their shear wave velocities (SWVs) were measured. From all of the masses, 30 were examined by two independent operators to evaluate the reproducibility of the results of VTQ measurement. All masses were later surgically resected, and the histologic results were correlated with the SWV results. A receiver operating characteristic curve was calculated to assess the diagnostic performance of VTQ. A total of 102 benign lesions and 41 carcinomas were diagnosed on the basis of histologic examination. The VTQ measurements performed by the two independent operators yielded a correlation coefficient of 0.885. Applying a cutoff point of 3.065 m/s, a significant difference (P < .001) was found between the SWVs of the benign (mean ± SD, 2.25 ± 0.59 m/s) and malignant (5.96 ± 2.96 m/s) masses. The sensitivity, specificity, and area under the receiver operating characteristic curve for the differentiation were 75.6%, 95.1%, and 85.6%, respectively. When the repeated non-numeric result X.XX of the SWV measurements was designated as an indicator of malignancy, the sensitivity, specificity, and accuracy were 63.4%, 100%, and 89.5%. Virtual Touch tissue quantification can yield reproducible and quantitative diagnostic information on solid breast masses and serve as an effective diagnostic tool for differentiation between benign and malignant solid masses.

Measurement and Modeling of Job Stress of Electric Overhead Traveling Crane Operators

PubMed Central

Krishna, Obilisetty B.; Maiti, Jhareswar; Ray, Pradip K.; Samanta, Biswajit; Mandal, Saptarshi; Sarkar, Sobhan

2015-01-01

Background In this study, the measurement of job stress of electric overhead traveling crane operators and quantification of the effects of operator and workplace characteristics on job stress were assessed. Methods Job stress was measured on five subscales: employee empowerment, role overload, role ambiguity, rule violation, and job hazard. The characteristics of the operators that were studied were age, experience, body weight, and body height. The workplace characteristics considered were hours of exposure, cabin type, cabin feature, and crane height. The proposed methodology included administration of a questionnaire survey to 76 electric overhead traveling crane operators followed by analysis using analysis of variance and a classification and regression tree. Results The key findings were: (1) the five subscales can be used to measure job stress; (2) employee empowerment was the most significant factor followed by the role overload; (3) workplace characteristics contributed more towards job stress than operator's characteristics; and (4) of the workplace characteristics, crane height was the major contributor. Conclusion The issues related to crane height and cabin feature can be fixed by providing engineering or foolproof solutions than relying on interventions related to the demographic factors. PMID:26929839

High Pb concentration stress on Typha latifolia growth and Pb removal in microcosm wetlands.

PubMed

Han, Jianqiu; Chen, Fengzhen; Zhou, Yumei; Wang, Chaohua

2015-01-01

When constructed wetlands are used to treat high-Pb wastewater, Pb may become a stress to wetland plants, which subsequently reduces treatment performance and the other ecosystem services. To facilitate the design and operation of constructed wetlands for treatment of Pb-rich wastewater, we investigated the irreversible inhibitory level of Pb for Typha latifolia through experiments in microcosm wetlands. Seven horizontal subsurface flow constructed wetlands were built with rectangular plastic tanks and packed with marble chips and sand. All wetlands were transplanted with nine stems of Typha latifolia each. The wetlands were batch operated in a greenhouse with artificial wastewater (10 L each) for 12 days. Influent to the seven wetlands had different concentrations of Pb: 0 mg/L, 10 mg/L, 25 mg/L, 50 mg/L, 100 mg/L, 200 mg/L, and 500 mg/L, respectively. The results suggested that leaf chlorophyll relative content, relative growth rate, photosynthetic characteristics, activities of superoxide dismutase, peroxidase, and content of malondialdehyde were not affected when initial Pb concentration was at 100 mg/L and below. But when initial Pb concentration was above 100 mg/L, all of them were seriously affected. We conclude that high Pb concentrations wastewater could inhibit the growth of Typha latifolia and decrease the removal rate of wetlands.

E-beam-pumped semiconductor lasers

NASA Astrophysics Data System (ADS)

Rice, Robert R.; Shanley, James F.; Ruggieri, Neil F.

1995-04-01

The collapse of the Soviet Union opened many areas of laser technology to the West. E-beam- pumped semiconductor lasers (EBSL) were pursued for 25 years in several Soviet Institutes. Thin single crystal screens of II-VI alloys (ZnxCd1-xSe, CdSxSe1-x) were incorporated in laser CRTs to produce scanned visible laser beams at average powers greater than 10 W. Resolutions of 2500 lines were demonstrated. MDA-W is conducting a program for ARPA/ESTO to assess EBSL technology for high brightness, high resolution RGB laser projection application. Transfer of II-VI crystal growth and screen processing technology is underway, and initial results will be reported. Various techniques (cathodoluminescence, one- and two-photon laser pumping, etc.) have been used to assess material quality and screen processing damage. High voltage (75 kV) video electronics were procured in the U.S. to operate test EBSL tubes. Laser performance was documented as a function of screen temperature, beam voltage and current. The beam divergence, spectrum, efficiency and other characteristics of the laser output are being measured. An evaluation of the effect of laser operating conditions upon the degradation rate is being carried out by a design-of-experiments method. An initial assessment of the projected image quality will be performed.

Adaptive fuzzy system for 3-D vision

NASA Technical Reports Server (NTRS)

Mitra, Sunanda

1993-01-01

An adaptive fuzzy system using the concept of the Adaptive Resonance Theory (ART) type neural network architecture and incorporating fuzzy c-means (FCM) system equations for reclassification of cluster centers was developed. The Adaptive Fuzzy Leader Clustering (AFLC) architecture is a hybrid neural-fuzzy system which learns on-line in a stable and efficient manner. The system uses a control structure similar to that found in the Adaptive Resonance Theory (ART-1) network to identify the cluster centers initially. The initial classification of an input takes place in a two stage process; a simple competitive stage and a distance metric comparison stage. The cluster prototypes are then incrementally updated by relocating the centroid positions from Fuzzy c-Means (FCM) system equations for the centroids and the membership values. The operational characteristics of AFLC and the critical parameters involved in its operation are discussed. The performance of the AFLC algorithm is presented through application of the algorithm to the Anderson Iris data, and laser-luminescent fingerprint image data. The AFLC algorithm successfully classifies features extracted from real data, discrete or continuous, indicating the potential strength of this new clustering algorithm in analyzing complex data sets. The hybrid neuro-fuzzy AFLC algorithm will enhance analysis of a number of difficult recognition and control problems involved with Tethered Satellite Systems and on-orbit space shuttle attitude controller.

Primary cardiac sarcoma complicated with cerebral infarction and brain metastasis: A case report and literature review.

PubMed

Sun, Yun-Peng; Wang, Xuan; Gao, Yong-Sheng; Zhao, Song; Bai, Yang

2017-12-12

In large autopsy series, the estimated frequency of primary tumors of the heart ranges from 0.0017% to 0.33%. Approximately 25% of primary cardiac tumors are malignant, and nearly 20% of these are sarcomas. To date, a completely feasible surgical resection remains the major treatment measure of cardiac sarcoma, especially for recurrent focal cardiac sarcoma and the recurrence of a restrictive metastasis. Although characteristically medical treatments are recommended, there is no consistent opinion for adjuvant radiotherapy and chemotherapy following an operation. Since these tumors usually undergo extensive spread by the time that the diagnosis is established, the prognosis of cardiac sarcoma remains poor. In this report, we described a case who underwent initial cardiac tumor resection, and was confirmed to be a pleomorphic undifferentiated sarcoma based on pathological findings. However, the patient complicated with cerebral infarction and subsequent brain metastasis sarcoma after the initial surgery, which was confirmed by brain tissue pathology. During the course of therapy, the patient underwent three surgical operations and refused to accept any chemotherapy and radiotherapy intervention. To the best of our knowledge, this is the first case report describing a primary cardiac sarcoma complicated with cerebral infarction and brain metastasis. The management of primary cardiac sarcoma is also discussed.

Characteristics of a productive research environment: literature review.

PubMed

Bland, C J; Ruffin, M T

1992-06-01

What environmental factors stimulate and maintain research productivity? To answer this question, the authors conducted an extensive review of articles and books on research productivity published from the mid-1960s through 1990. This review revealed that a consistent set of 12 characteristics was found in research-conducive environments: (1) clear goals that serve a coordinating function, (2) research emphasis, (3) distinctive culture, (4) positive group climate, (5) assertive participative governance, (6) decentralized organization, (7) frequent communication, (8) accessible resources, particularly human, (9) sufficient size, age, and diversity of the research group, (10) appropriate rewards, (11) concentration on recruitment and selection, and (12) leadership with research expertise and skill in both initiating appropriate organizational structure and using participatory management practices. Some of these characteristics are not surprising, although some findings were unexpected, such as that participative governance correlated consistently with research productivity. The differential impact of each of these 12 characteristics is unclear. It is clear, however, that the leader has a disproportionate impact through his or her influence on all of the other characteristics. Yet, an overarching feature of these characteristics is their interdependency. These factors do not operate in research groups as isolated characteristics. Rather, they are like fine threads of a whole fabric: individual, yet when interwoven, providing a strong, supportive, and stimulating backdrop for the researcher. The authors conclude that while at a distance the productive research enterprise looks like a highly robust entity, upon closer inspection it is revealed to be a delicate structure highly dependent on the existence and effective working of numerous individual, organizational, and leadership characteristics.

Design of a receiver operating characteristic (ROC) study of 10:1 lossy image compression

NASA Astrophysics Data System (ADS)

Collins, Cary A.; Lane, David; Frank, Mark S.; Hardy, Michael E.; Haynor, David R.; Smith, Donald V.; Parker, James E.; Bender, Gregory N.; Kim, Yongmin

1994-04-01

The digital archiving system at Madigan Army Medical Center (MAMC) uses a 10:1 lossy data compression algorithm for most forms of computed radiography. A systematic study on the potential effect of lossy image compression on patient care has been initiated with a series of studies focused on specific diagnostic tasks. The studies are based upon the receiver operating characteristic (ROC) method of analysis for diagnostic systems. The null hypothesis is that observer performance with approximately 10:1 compressed and decompressed images is not different from using original, uncompressed images for detecting subtle pathologic findings seen on computed radiographs of bone, chest, or abdomen, when viewed on a high-resolution monitor. Our design involves collecting cases from eight pathologic categories. Truth is determined by committee using confirmatory studies performed during routine clinical practice whenever possible. Software has been developed to aid in case collection and to allow reading of the cases for the study using stand-alone Siemens Litebox workstations. Data analysis uses two methods, ROC analysis and free-response ROC (FROC) methods. This study will be one of the largest ROC/FROC studies of its kind and could benefit clinical radiology practice using PACS technology. The study design and results from a pilot FROC study are presented.

Receiver operating characteristic curve analysis of the Child Behavior Checklist and Teacher’s Report Form for assessing autism spectrum disorder in preschool-aged children

PubMed Central

Bara, Tiago S; Farias, Antonio C; Felden, Erico PG; Cordeiro, Mara L

2018-01-01

Background Autism spectrum disorder (ASD) is a neurodevelopmental disorder characterized by social, behavioral, and communication impairments with an estimated prevalence of 1 in 68 school-aged children. There is a need for objective and easily applicable instruments for early identification of autistic children to enable initiation of early interventions during a very sensitive period of brain development and, consequently, optimize prognosis. Here, we tested the utility of the Child Behavior Checklist (CBCL) and the Caregiver-Teacher’s Report Form (C-TRF) scales for assessing ASD in Brazil, where ASD screening research is emergent. Subjects and methods A total of 70 children (2–5 years old, both sexes) were enrolled, including an ASD group (n=39) and a non-ASD control group (n=31). The preschool versions of the CBCL and C-TRF were applied. The CBCL and C-TRF results were compared between the ASD and non-ASD control groups with Mann–Whitney U tests and receiver operating characteristic analyses. Results The CBCL and C-TRF were found to have moderate accuracy for the dimensions withdrawn and autism spectrum problems, and to correlate with each other. Conclusion The CBCL and C-TRF may aid in early ASD detection. PMID:29343961

Characteristics of initial fearful spells and their associations with DSM-IV panic attacks and panic disorder in adolescents and young adults from the community.

PubMed

Asselmann, Eva; Pané-Farré, Christiane; Isensee, Barbara; Wittchen, Hans-Ulrich; Lieb, Roselind; Höfler, Michael; Beesdo-Baum, Katja

2014-08-01

Few studies examined characteristics of initial fearful spells (FS) or panic attacks (PA) and their relation to DSM-IV PA and panic disorder (PD). A community sample of adolescents and young adults (N=3021) was followed up in 4 waves (T0-T3) over up to 10 years. FS, PA, and PD were assessed at each wave using the DSM-IV/M-CIDI. Characteristics of the initial FS/PA including perceived reasons/triggers, appraisal, duration, and behavioral/emotional consequences of the initial FS/PA were retrospectively assessed at T1 and T2 in those reporting the experience of lifetime FS or PA at these waves (N=363). Multinomial logistic regressions adjusted for sex and age were used to reveal associations of initial FS/PA characteristics (aggregated data from T1 and T2) with PA only (N=88) and PD (N=62; lifetime incidences cumulated across assessment waves) (reference group: No PA/PD). Alcohol consumption, drugs/medication, and physical illness as perceived reasons for the initial FS/PA were associated with PA-only (OR 2.46-5.44), while feelings of depression, feelings of anxiety, and having always been anxious/nervous as perceived reasons for the initial FS/PA, appraising the initial FS/PA as terrible and long-term irritating/burdensome, subsequent feelings of depression, subsequent avoidance, and subsequent consumption of medication, alcohol, or drugs were associated with PD (OR 2.64-4.15). A longer duration until "feeling okay again" was associated with both PA-only (OR=1.29 per category) and PD (OR=1.63). Initial FS/PA characteristics were necessarily assessed retrospectively by self-report only. Thus, our data might be subject to recall/evaluation biases. Aggregated data were used and strictly prospective-longitudinal studies are necessary that replicate our findings. Assessing initial FS/PA characteristics might be useful to identify individuals at increased risk for more severe panic pathology. Copyright © 2014 Elsevier B.V. All rights reserved.

Sea Ice Characteristics and the Open-Linked Data World

NASA Astrophysics Data System (ADS)

Khalsa, S. J. S.; McGuinness, D. L.; Duerr, R.; Pulsifer, P. L.; Fox, P. A.; Thompson, C.; Yan, R.

2014-12-01

The audience for sea ice data sets has broadened dramatically over the past several decades. Initially the National Snow and Ice Data Center (NSIDC) sea ice products were used primarily by sea ice specialists. However, now they are in demand by researchers in many different domains and some are used by the public. This growth in the number and type of users has presented challenges to content providers aimed particularly at supporting interdisciplinary and multidisciplinary data use. In our experience, it is generally insufficient to simply make the data available as originally formatted. New audiences typically need data in different forms; forms that meet their needs, that work with their specific tools. Moreover, simple data reformatting is rarely enough. The data needs to be aggregated, transformed or otherwise converted into forms that better serve the needs of the new audience. The Semantic Sea Ice Interoperability Initiative (SSIII) is an NSF-funded research project aimed at making sea ice data more useful to more people using semantic technologies. The team includes domain and science data experts as well as knowledge representation and linked data experts. Beginning with a series of workshops involving members of the operations, sea ice research and modeling communities, as well as members of local communities in Alaska, a suite of ontologies describing the physical characteristics of sea ice have been developed and used to provide one of NSIDC's data sets, the operational Arctic sea ice charts obtained from the Canadian Ice Center, as open-linked data. These data extend nearly a decade into the past and can now be queried either directly through a publicly available SPARQL end point (for those who are familiar with open-linked data) or through a simple Open Geospatial Consortium (OGC) standards map-based query tool. Questions like "What were the characteristics (i.e., sea ice concentration, form and stage of development) of the sea ice in the region surrounding my ship/polar bear on date X?" can now be answered. This service may be of interest within the broad polar community - especially those who already are familiar with either open-linked data or OGC services. We seek feedback, collaborators, and users.

40 CFR 63.6610 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2010 CFR

2010-07-01

... initial performance tests or other initial compliance demonstrations if I own or operate a stationary RICE... performance tests or other initial compliance demonstrations if I own or operate a stationary RICE with a site... stationary RICE with a site rating of more than 500 brake HP located at a major source of HAP emissions you...

40 CFR 63.6610 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2011 CFR

2011-07-01

... initial performance tests or other initial compliance demonstrations if I own or operate a stationary RICE... performance tests or other initial compliance demonstrations if I own or operate a stationary RICE with a site... stationary RICE with a site rating of more than 500 brake HP located at a major source of HAP emissions you...

40 CFR Table 2 to Subpart Rrr of... - Summary of Operating Requirements for New and Existing Affected Sources and Emission Units

Code of Federal Regulations, 2011 CFR

2011-07-01

... with fabric filter Bag leak detector or Initiate corrective action within 1-hr of alarm and complete in... operation Operate in accordance with OM&M plan. b Bag leak detector or Initiate corrective action within 1... accordance with OM&M plan. b Dross-only furnace with fabric filter Bag leak detector or Initiate corrective...

Initial Costs vs. Operational Costs. A Study of Building Improvement Projects in Fourteen Schools in the School District of Greenville County, South Carolina.

ERIC Educational Resources Information Center

Chan, Tak Cheung

To determine whether initial facility improvement costs were paid back by the reduced operational costs resulting from the improvement projects, this study examined the relationship between initial costs and operational costs of fourteen school buildings improved during the 1978-79 school year in Greenville County, South Carolina. With energy…

Use of laterite for the removal of fluoride from contaminated drinking water.

PubMed

Sarkar, Mitali; Banerjee, Aparna; Pramanick, Partha Pratim; Sarkar, Asit R

2006-10-15

The effects of different operational variables on the mechanistic function of laterite in removal of fluoride have been investigated. Thermodynamic parameters such as free energy change, enthalpy, and entropy of the process, as well as the sorption isotherm, were evaluated. The extent of solute removal is determined by initial solute concentration, operational conditions, laterite dose, and solution pH. For a fixed set of experimental conditions, a model equation is developed from which the percent removal corresponding to each load of fluoride is determined. The mechanism of fluoride adsorption is governed by the zero point charge of laterite and follows a first-order rate equation. pH has a vital role influencing the surface characteristics of laterite. To simulate the flow dynamics, fluoride solution was run through a fixed bed column. The pattern of breakthrough curves for different influent fluoride concentration, pH, and column bed height was characterized. The column efficiency was tested from the bed depth-service time model. The elution of the retained fluoride was studied and the effectiveness of column operation was determined by the retention-elution cycles.

A tandem mirror hybrid plume plasma propulsion facility

NASA Technical Reports Server (NTRS)

Chang-Diaz, F. R.; Yang, T. F.; Krueger, W. A.; Peng, S.; Urbahn, J.; Yao, X.; Griffin, D.

1988-01-01

A concept in electrodeless plasma propulsion, which is also capable of delivering a variable Isp, is presented. The concept involves a three-stage system of plasma injection, heating, and subsequent ejection through a magnetic nozzle. The nozzle produces the hybrid plume by the coaxial injection of hypersonic neutral gas. The gas layer, thus formed, protects the material walls from the hot plasma and, through increased collisions, helps detach it from the diverging magnetic field. The physics of this concept is evaluated numerically through full spatial and temporal simulations; these explore the operating characteristics of such a device over a wide region of parameter space. An experimental facility to study the plasma dynamics in the hybrid plume was built. The device consists of a tandem mirror operating in an asymmetric mode. A later upgrade of this system will incorporate a cold plasma injector at one end of the machine. Initial experiments involve the full characterization of the operating envelope, as well as extensive measurements of plasma properties at the exhaust. The results of the numerical simulations are described.

Memristive device based on a depletion-type SONOS field effect transistor

NASA Astrophysics Data System (ADS)

Himmel, N.; Ziegler, M.; Mähne, H.; Thiem, S.; Winterfeld, H.; Kohlstedt, H.

2017-06-01

State-of-the-art SONOS (silicon-oxide-nitride-oxide-polysilicon) field effect transistors were operated in a memristive switching mode. The circuit design is a variation of the MemFlash concept and the particular properties of depletion type SONOS-transistors were taken into account. The transistor was externally wired with a resistively shunted pn-diode. Experimental current-voltage curves show analog bipolar switching characteristics within a bias voltage range of ±10 V, exhibiting a pronounced asymmetric hysteresis loop. The experimental data are confirmed by SPICE simulations. The underlying memristive mechanism is purely electronic, which eliminates an initial forming step of the as-fabricated cells. This fact, together with reasonable design flexibility, in particular to adjust the maximum R ON/R OFF ratio, makes these cells attractive for neuromorphic applications. The relative large set and reset voltage around ±10 V might be decreased by using thinner gate-oxides. The all-electric operation principle, in combination with an established silicon manufacturing process of SONOS devices at the Semiconductor Foundry X-FAB, promise reliable operation, low parameter spread and high integration density.

Influence of relaxation modes on membrane fouling in submerged membrane bioreactor for domestic wastewater treatment.

PubMed

Habib, Rasikh; Asif, Muhammad Bilal; Iftekhar, Sidra; Khan, Zahiruddin; Gurung, Khum; Srivastava, Varsha; Sillanpää, Mika

2017-08-01

Relaxation and backwashing have become an integral part of membrane bioreactor (MBR) operations for fouling control. This study was carried out on real municipal wastewater to evaluate the influence of different operational strategies on membrane fouling at equivalent water yield. Four relaxation modes (MBR 10+0, MBR 10+1 , MBR 10+1.5 and MBR 10+2 ) were tested to analyze membrane fouling behavior. For the optimization of relaxation modes, fouling rate in terms of trans-membrane pressure, hydraulic resistances and characteristics of fouling fractions were analyzed. It has been observed that cake layer resistance was minimum in MBR 10+1.5 but pore blockage resistance was increased in all relaxation modes. Moreover, high instantaneous flux contributed significantly to fouling rate at the initial stage of MBR operations. Relaxation modes were also efficient in removing irreversible fouling to some extent. Under all relaxation modes, COD removal efficiency ranged from 92 to 96.5%. Ammonium and TP removal were on the lower side due to the short solids and hydraulic retention time. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chronic thromboembolic pulmonary hypertension (CTEPH): results from an international prospective registry.

PubMed

Pepke-Zaba, Joanna; Delcroix, Marion; Lang, Irene; Mayer, Eckhard; Jansa, Pavel; Ambroz, David; Treacy, Carmen; D'Armini, Andrea M; Morsolini, Marco; Snijder, Repke; Bresser, Paul; Torbicki, Adam; Kristensen, Bent; Lewczuk, Jerzy; Simkova, Iveta; Barberà, Joan A; de Perrot, Marc; Hoeper, Marius M; Gaine, Sean; Speich, Rudolf; Gomez-Sanchez, Miguel A; Kovacs, Gabor; Hamid, Abdul Monem; Jaïs, Xavier; Simonneau, Gérald

2011-11-01

Chronic thromboembolic pulmonary hypertension (CTEPH) is often a sequel of venous thromboembolism with fatal natural history; however, many cases can be cured by pulmonary endarterectomy. The clinical characteristics and current management of patients enrolled in an international CTEPH registry was investigated. The international registry included 679 newly diagnosed (≤6 months) consecutive patients with CTEPH, from February 2007 until January 2009. Diagnosis was confirmed by right heart catheterization, ventilation-perfusion lung scintigraphy, computerized tomography, and/or pulmonary angiography. At diagnosis, a median of 14.1 months had passed since first symptoms; 427 patients (62.9%) were considered operable, 247 (36.4%) nonoperable, and 5 (0.7%) had no operability data; 386 patients (56.8%, ranging from 12.0%- 60.9% across countries) underwent surgery. Operable patients did not differ from nonoperable patients relative to symptoms, New York Heart Association class, and hemodynamics. A history of acute pulmonary embolism was reported for 74.8% of patients (77.5% operable, 70.0% nonoperable). Associated conditions included thrombophilic disorder in 31.9% (37.1% operable, 23.5% nonoperable) and splenectomy in 3.4% of patients (1.9% operable, 5.7% nonoperable). At the time of CTEPH diagnosis, 37.7% of patients initiated at least 1 pulmonary arterial hypertension-targeted therapy (28.3% operable, 53.8% nonoperable). Pulmonary endarterectomy was performed with a 4.7% documented mortality rate. Despite similarities in clinical presentation, operable and nonoperable CTEPH patients may have distinct associated medical conditions. Operability rates vary considerably across countries, and a substantial number of patients (operable and nonoperable) receive off-label pulmonary arterial hypertension-targeted treatments.

Flight Studies of Problems Pertinent to High-Speed Operation of Jet Transports

NASA Technical Reports Server (NTRS)

Butchart, Stanley P.; Fischel, Jack; Tremant, Robert A.; Robinson, Glenn H.

1959-01-01

A flight investigation was made to assess the potential operational problems of jet transports in the transonic cruise range. In this study a large multiengine jet airplane having geometric characteristics fairly representative of the jet transport was used; however, in order to ensure general applicability of the results, the aerodynamic characteristics of the test airplane were varied to simulate a variety of jet- transport airplanes. Some of the specific areas investigated include: (1) an overall evaluation of longitudinal stability and control characteristics at transonic speeds, with an assessment of pitch-up characteristics, (2) the effect of buffeting on airplane operational speeds and maneuvering, (3) the desirable lateral-directional damping characteristics, (4) the desirable lateral-control characteristics, (5) an assessment of over-speed and speed-spread requirements, including the upset maneuver, and (6) an assessment of techniques and airplane characteristics for rapid descent and slow-down. The results presented include pilots' evaluation of the various problem areas and specific recommendations for possible improvement of jet-transport operations in the cruising speed range.

Study of operator's information in the course of complicated and combined activity

NASA Astrophysics Data System (ADS)

Krylova, N. V.; Bokovikov, A. K.

1982-08-01

Speech characteristics of operators performing control and observation operations, Information reception, transmission and processing, and decision making when exposed to the real stress of parachute jumps were investigated. Form and content speech characteristics whose variations reflect the level of operators adaptation to stressful activities are reported.

14 CFR 33.51 - Operation test.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: AIRCRAFT ENGINES Block Tests; Reciprocating Aircraft Engines § 33.51 Operation test. The... characteristics, starting, idling, acceleration, overspeeding, functioning of propeller and ignition, and any other operational characteristic of the engine. If the engine incorporates a multispeed supercharger...

14 CFR 33.51 - Operation test.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: AIRCRAFT ENGINES Block Tests; Reciprocating Aircraft Engines § 33.51 Operation test. The... characteristics, starting, idling, acceleration, overspeeding, functioning of propeller and ignition, and any other operational characteristic of the engine. If the engine incorporates a multispeed supercharger...

Differential Weight Procedure of the Conditional P.D.F. Approach for Estimating the Operating Characteristics of Discrete Item Responses.

ERIC Educational Resources Information Center

Samejima, Fumiko

A method is proposed that increases the accuracies of estimation of the operating characteristics of discrete item responses, especially when the true operating characteristic is represented by a steep curve, and also at the lower and upper ends of the ability distribution where the estimation tends to be inaccurate because of the smaller number…

Public Health Service--health maintenance organizations: final regulations.

PubMed

1980-01-24

These rules amend the Public Health Service (PHS) regulations by implementing certain changes made by the HMO Amendments of 1978 with respect to grants and loan guarantees for planning and initial development costs (Subpart D) and to loans and loan guarantees for initial costs of operation (Subpart E). These regulations change Subpart D by including projects for the "expansion of services" of an HMO among the projects eligible for initial development assistance. In addition, they change the limits on the amount of assistance permitted for initial development projects. These regulations also change Subpart E by substituting the words "costs of operation" for the words "operating costs," thereby expanding the scope of assistance for initial operations (1) to include costs of certain small capital expenditures for equipment and alterations and renovations of facilities and (2) to incorporate into the regulations a longstanding policy which specifies the amount of preaward balance sheet liabilities which may be paid for with funds under operating loans (whether made directly or guaranteed by the Secretary).

Surgeon specialization and use of sentinel lymph node biopsy for breast cancer.

PubMed

Yen, Tina W F; Laud, Purushuttom W; Sparapani, Rodney A; Nattinger, Ann B

2014-02-01

Sentinel lymph node biopsy (SLNB) is the standard of care for axillary staging in patients with clinically node-negative breast cancer. It is not known whether SLNB rates differ by surgeon expertise. If surgeons with less breast cancer expertise are less likely to offer SLNB to these patients, this practice pattern could lead to unnecessary axillary lymph node dissections and lymphedema. To explore potential measures of surgical expertise (including a novel objective specialization measure: percentage of a surgeon's operations performed for breast cancer determined from Medicare claims) on the use of SLNB for invasive breast cancer. A population-based prospective cohort study was conducted in California, Florida, and Illinois. Participants included elderly (65-89 years) women identified from Medicare claims as having had incident invasive breast cancer surgery in 2003. Patient, tumor, treatment, and surgeon characteristics were examined. Type of axillary surgery performed. Of 1703 women who received treatment by 863 surgeons, 56.4% underwent an initial SLNB, 37.2% initial axillary lymph node dissection, and 6.3% no axillary surgery. The median annual surgeon Medicare volume of breast cancer cases was 6.0 (range, 1.5-57.0); the median surgeon percentage of breast cancer cases was 4.5% (range, 0.4%-100.0%). After multivariable adjustment of patient and surgeon factors, women operated on by surgeons with higher volumes and percentages of breast cancer cases had a higher likelihood of undergoing SLNB. Specifically, women were most likely to undergo SLNB if the operation was performed by high-volume surgeons (regardless of percentage) or by lower-volume surgeons with a high percentage of breast cancer cases. In addition, membership in the American Society of Breast Surgeons (odds ratio, 1.98; 95% CI, 1.51-2.60) and Society of Surgical Oncology (1.59; 1.09-2.30) were independent predictors of women undergoing an initial SLNB. Patients who receive treatment from surgeons with more experience with and focus on breast cancer are significantly more likely to undergo SLNB, highlighting the importance of receiving initial treatment by specialized providers. Factors relating to specialization in a particular area, including our novel surgeon percentage measure, require further investigation as potential indicators of quality of care.

The Effect of Boron on the Low Cycle Fatigue Behavior of Disk Alloy KM4

NASA Technical Reports Server (NTRS)

Gabb, Timothy; Gayda, John; Sweeney, Joseph

2000-01-01

The durability of powder metallurgy nickel base superalloys employed as compressor and turbine disks is often limited by low cycle fatigue (LCF) crack initiation and crack growth from highly stressed surface locations (corners, holes, etc.). Crack growth induced by dwells at high stresses during aerospace engine operation can be particularly severe. Supersolvus solution heat treatments can be used to produce coarse grain sizes approaching ASTM 6 for improved resistance to dwell fatigue crack growth. However, the coarse grain sizes reduce yield strength, which can lower LCF initiation life. These high temperature heat treatments also can encourage pores to form. In the advanced General Electric disk superalloy KM4, such pores can initiate fatigue cracks that limit LCF initiation life. Hot isostatic pressing (HIP) during the supersolvus solution heat treatment has been shown to improve LCF initiation life in KM4, as the HIP pressure minimizes formation of the pores. Reduction of boron levels in KM4 has also been shown to increase LCF initiation life after a conventional supersolvus heat treatment, again possibly due to effects on the formation tendencies of these pores. However, the effects of reduced boron levels on microstructure, pore characteristics, and LCF failure modes in KM4 still need to be fully quantified. The objective of this study was to determine the effect of boron level on the microstructure, porosity, LCF behavior, and failure modes of supersolvus heat treated KM4.

Operational evaluation of initial data link air traffic control services, Vol. 1

DOT National Transportation Integrated Search

1990-02-01

This report details the results of an operational evaluation of Initial Data Link Air Traffic Control (ATC) Services. The Operational Evaluation was conducted at the Federal Aviation Administration (FAA) Technical Center utilizing the Data Link test ...

Operational evaluation of initial data link air traffic control services, Vol. 2 - Appendixes

DOT National Transportation Integrated Search

1990-02-01

This report details the results of an operational evaluation of Initial Data : LInk Air Traffic Control (ATC) Services. The Operational Evaluation was : conducted at the Federal Aviation Administration (FAA)Technical Center utilizing : the Data Link ...

M109 Family of Vehicles, Paladin Integrated Management (PIM): Operational Assessment of the Initial Operational Test and Evaluation (IOT and E)

DTIC Science & Technology

2017-01-01

procedures and Army doctrine. During pre -IOT&E training and developmental testing , the combat developer discovered that when projectiles were fired using...Director, Operational Test and Evaluation M109 Family of Vehicles, Paladin Integrated Management (PIM) Operational Assessment of the...Initial Operational Test and Evaluation October 2011 January 2017 J. Michael Gilmore Director

Vehicle operation characteristic under different ramp entrance conditions in underground road: Analysis, simulation and modelling

NASA Astrophysics Data System (ADS)

Yao, Qiming; Liu, Shuo; Liu, Yang

2018-05-01

An experimental design was used to study the vehicle operation characteristics of different ramp entrance conditions in underground road. With driving simulator, the experimental scenarios include left or right ramp with first, second and third service level, respectively, to collect vehicle speed, acceleration, lateral displacement and location information at the ramp entrance section. By using paired t-test and ANOVA, the influence factors of vehicle operating characteristics are studied. The result shows that effects of ramp layout and mainline traffic environment on vehicle operation characteristics are significant. The regression model of vehicle traveling distance on acceleration lane is established. Suggestions are made for ramp entrance design of underground road.

Impact of anatomic characteristics and initial biventricular surgical strategy on outcomes in various forms of double-outlet right ventricle.

PubMed

Villemain, Olivier; Belli, Emre; Ladouceur, Magalie; Houyel, Lucile; Jalal, Zakaria; Lambert, Virginie; Ly, Mohamed; Vouhé, Pascal; Bonnet, Damien

2016-09-01

Surgical management of various forms of double-outlet right ventricle uses a variety of approaches depending on the underlying anatomic form. In this study, we sought to determine the risk factors of mortality and reoperation in those with double-outlet right ventricle undergoing biventricular repair, according to anatomic characteristics and initial surgical strategy. Between 1992 and 2013, 433 patients were included in the study. Double-outlet right ventricle was classified as double-outlet right ventricle with subaortic ventricular septal defect associated with subpulmonary obstruction in 33% of patients (n = 141), with subaortic ventricular septal defect without subpulmonary obstruction in 30% of patients (n = 130), with subpulmonary ventricular septal defect in 32% of patients (n = 139), and with noncommitted ventricular septal defect in 5% of patients (n = 23). Three types of repairs were performed: (1) intraventricular baffle repair, n = 149 (34%); (2) intraventricular baffle repair with right ventricular outflow tract reconstruction, n = 163 (38%); and (3) intraventricular baffle repair with arterial switch operation, n = 121 (28%). Thirty-day overall mortality was 7.4%. Early reoperation was needed in 6% of the cases. Early mortality was higher in the intraventricular baffle repair with arterial switch operation group (P = .01). Survival at 10 years was 86.2%, and freedom from reoperation at 10 years was 61.4%. At last follow-up (median, 5.7 years; 95% confidence interval, 4.5-6.6), mortality and reoperation rates were similar in the different surgical strategy groups. Late reoperation and late mortality were significantly higher in the double-outlet right ventricle with noncommitted ventricular septal defect group (P < .01). In multivariate analyses, risk factors for reoperation were concomitant surgical procedures (P = .03) and duration of cardiopulmonary bypass (P < .01). Risk factors for mortality were restrictive ventricular septal defect (P = .01), mitral cleft (P < .01), and associated coronary artery anomalies (P = .01). Those with the anatomic type of double-outlet right ventricle with noncommitted ventricular septal defect were at higher risk for reoperation and mortality. Intraventricular baffle repair with arterial switch operation was the surgical strategy in patients at higher risk of early death. Initial surgical strategy did not influence the late outcomes. Copyright © 2016 The American Association for Thoracic Surgery. Published by Elsevier Inc. All rights reserved.

Robot-assisted partial nephrectomy: continued refinement of outcomes beyond the initial learning curve.

PubMed

Paulucci, David J; Abaza, Ronney; Eun, Daniel D; Hemal, Ashok K; Badani, Ketan K

2017-05-01

To evaluate trends in peri-operative outcomes of 250 consecutive cases beyond the initial learning curve (LC) of robot-assisted partial nephrectomy (RAPN) among multiple surgeons. A multi-institutional database was used to evaluate trends in patient demographics (e.g. age, gender, comorbidities), tumour characteristics (e.g. size, complexity) and peri-operative outcomes (e.g. warm ischaemia time [WIT], operating time, complications, estimated blood loss [EBL], trifecta achievement) in consecutive cases 50-300 (n = 960) from 2008 to 2016 among four experienced surgeons. Trends in outcomes were assessed using multivariable regression models adjusted for demographic and tumour-specific variables. Outcomes for cases 50-99 were compared with those for cases 250-300. In the study period RAPN was increasingly performed in patients with larger tumours (β = 0.001, P = 0.048), hypertension (odds ratio [OR] 1.003; P = 0.008) diabetes (OR 1.003; P = 0.025) and previous abdominal surgery (OR 1.003; P = 0.006). Surgeon experience was associated with more trifecta achievement (OR 1.006; P < 0.001), shorter WIT (β = -0.036, P < 0.001), less EBL (β = -0.154, P = 0.009), fewer blood transfusions (OR 0.989, P = 0.024) and a reduced length of hospital stay (β = -0.002, P = 0.002), but not with operating time (P = 0.243), complications (P = 0.587) or surgical margin status (P = 0.102). Tumour size and WIT in cases 50-99 vs 250-300 were 2.7 vs 3.2 cm (P = 0.001) and 21.4 vs 16.2 min (P < 0.001), respectively. Refinement of RAPN outcomes, concomitant with the treatment of a patient population with larger tumours and more comorbidities, occurs after the initial LC is reached. Although RAPN can consistently be performed safely with acceptable outcomes after a small number of cases, improvement in trifecta achievement, WIT, EBL, blood transfusions and a shorter hospitalization continues to occur up to 300 procedures. © 2016 The Authors BJU International © 2016 BJU International Published by John Wiley & Sons Ltd.

40 CFR 63.9565 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... limitation (including any operating limit) in this subpart during startup, shutdown, or malfunction.... Examples include hexane, toluene, and trichloroethylene. Initial startup means the first time that equipment is put into operation. Initial startup does not include operation solely for testing equipment...

40 CFR 63.9565 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... limitation (including any operating limit) in this subpart during startup, shutdown, or malfunction.... Examples include hexane, toluene, and trichloroethylene. Initial startup means the first time that equipment is put into operation. Initial startup does not include operation solely for testing equipment...

40 CFR 63.9565 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... limitation (including any operating limit) in this subpart during startup, shutdown, or malfunction.... Examples include hexane, toluene, and trichloroethylene. Initial startup means the first time that equipment is put into operation. Initial startup does not include operation solely for testing equipment...

40 CFR 63.9565 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... limitation (including any operating limit) in this subpart during startup, shutdown, or malfunction.... Examples include hexane, toluene, and trichloroethylene. Initial startup means the first time that equipment is put into operation. Initial startup does not include operation solely for testing equipment...

Life and Reliability Characteristics of TurboBrayton Coolers

NASA Technical Reports Server (NTRS)

Breedlove, Jeff J.; Zagarola, Mark; Nellis, Greg; Dolan, Frank; Swift, Walt; Gibbon, Judith; Obenschain, Arthur F. (Technical Monitor)

2000-01-01

Wear and internal contaminants are two of the primary factors that influence reliable, long-life operation of turbo-Brayton cryocoolers. This paper describes tests that have been conducted and methods that have been developed for turbo-Brayton components and systems to assure reliable operation. The turbomachines used in these coolers employ self-acting gas bearings to support the miniature high-speed shafts, thus providing vibration-free operation. Because the bearings are self-acting, rubbing contact occurs during initial start-up and shutdown of the machines. Bearings and shafts are designed to endure multiple stop/start cycles without producing particles or surface features that would impair the proper operation of the machines. Test results are presented for a variety of turbomachines used in these systems. The tests document extended operating life and start/stop cycling behavior for machines over a range of time and temperature scales. Contaminants such as moisture and other residual gas impurities can be a source of degraded operation if they freeze out in sufficient quantities to block flow passages or if they mechanically affect the operation of the machines. A post-fabrication bakeout procedure has been successfully used to reduce residual internal contamination to acceptable levels in a closed cycle system. The process was developed during space qualification tests on the NICMOS cryocooler. Moisture levels were sampled over a six-month time interval confirming the effectiveness of the technique. A description of the bakeout procedure is presented.

Analysis of the learning curve for peroral endoscopic myotomy for esophageal achalasia: Single-center, two-operator experience.

PubMed

Lv, Houning; Zhao, Ningning; Zheng, Zhongqing; Wang, Tao; Yang, Fang; Jiang, Xihui; Lin, Lin; Sun, Chao; Wang, Bangmao

2017-05-01

Peroral endoscopic myotomy (POEM) has emerged as an advanced technique for the treatment of achalasia, and defining the learning curve is mandatory. From August 2011 to June 2014, two operators in our institution (A&B) carried out POEM on 35 and 33 consecutive patients, respectively. Moving average and cumulative sum (CUSUM) methods were used to analyze the POEM learning curve for corrected operative time (cOT), referring to duration of per centimeter myotomy. Additionally, perioperative outcomes were compared among distinct learning curve phases. Using the moving average method, cOT reached a plateau at the 29th case and at the 24th case for operators A and B, respectively. CUSUM analysis identified three phases: initial learning period (Phase 1), efficiency period (Phase 2) and mastery period (Phase 3). The relatively smooth state in the CUSUM graph occurred at the 26th case and at the 24th case for operators A and B, respectively. Mean cOT of distinct phases for operator A were 8.32, 5.20 and 3.97 min, whereas they were 5.99, 3.06 and 3.75 min for operator B, respectively. Eckardt score and lower esophageal sphincter pressure significantly decreased during the 1-year follow-up period. Data were comparable regarding patient characteristics and perioperative outcomes. This single-center study demonstrated that expert endoscopists with experience in esophageal endoscopic submucosal dissection reached a plateau in learning of POEM after approximately 25 cases. © 2016 Japan Gastroenterological Endoscopy Society.

Bootstrap-based procedures for inference in nonparametric receiver-operating characteristic curve regression analysis.

PubMed

Rodríguez-Álvarez, María Xosé; Roca-Pardiñas, Javier; Cadarso-Suárez, Carmen; Tahoces, Pablo G

2018-03-01

Prior to using a diagnostic test in a routine clinical setting, the rigorous evaluation of its diagnostic accuracy is essential. The receiver-operating characteristic curve is the measure of accuracy most widely used for continuous diagnostic tests. However, the possible impact of extra information about the patient (or even the environment) on diagnostic accuracy also needs to be assessed. In this paper, we focus on an estimator for the covariate-specific receiver-operating characteristic curve based on direct regression modelling and nonparametric smoothing techniques. This approach defines the class of generalised additive models for the receiver-operating characteristic curve. The main aim of the paper is to offer new inferential procedures for testing the effect of covariates on the conditional receiver-operating characteristic curve within the above-mentioned class. Specifically, two different bootstrap-based tests are suggested to check (a) the possible effect of continuous covariates on the receiver-operating characteristic curve and (b) the presence of factor-by-curve interaction terms. The validity of the proposed bootstrap-based procedures is supported by simulations. To facilitate the application of these new procedures in practice, an R-package, known as npROCRegression, is provided and briefly described. Finally, data derived from a computer-aided diagnostic system for the automatic detection of tumour masses in breast cancer is analysed.

40 CFR 63.4751 - How do I demonstrate initial compliance with the emission limitations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... emission rate without add-on controls option for any individual coating operation, for any group of coating operations in the affected source, or for all the coating operations in the affected source. You must use... operation in the affected source for which you do not use this option. To demonstrate initial compliance...

CIS-lunar space infrastructure lunar technologies: Executive summary

NASA Technical Reports Server (NTRS)

Faller, W.; Hoehn, A.; Johnson, S.; Moos, P.; Wiltberger, N.

1989-01-01

Technologies necessary for the creation of a cis-Lunar infrastructure, namely: (1) automation and robotics; (2) life support systems; (3) fluid management; (4) propulsion; and (5) rotating technologies, are explored. The technological focal point is on the development of automated and robotic systems for the implementation of a Lunar Oasis produced by Automation and Robotics (LOAR). Under direction from the NASA Office of Exploration, automation and robotics were extensively utilized as an initiating stage in the return to the Moon. A pair of autonomous rovers, modular in design and built from interchangeable and specialized components, is proposed. Utilizing a buddy system, these rovers will be able to support each other and to enhance their individual capabilities. One rover primarily explores and maps while the second rover tests the feasibility of various materials-processing techniques. The automated missions emphasize availability and potential uses of Lunar resources, and the deployment and operations of the LOAR program. An experimental bio-volume is put into place as the precursor to a Lunar environmentally controlled life support system. The bio-volume will determine the reproduction, growth and production characteristics of various life forms housed on the Lunar surface. Physicochemical regenerative technologies and stored resources will be used to buffer biological disturbances of the bio-volume environment. The in situ Lunar resources will be both tested and used within this bio-volume. Second phase development on the Lunar surface calls for manned operations. Repairs and re-configuration of the initial framework will ensue. An autonomously-initiated manned Lunar oasis can become an essential component of the United States space program.

14 CFR 133.41 - Flight characteristics requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Flight characteristics requirements. 133.41... EXTERNAL-LOAD OPERATIONS Airworthiness Requirements § 133.41 Flight characteristics requirements. (a) The applicant must demonstrate to the Administrator, by performing the operational flight checks prescribed in...

14 CFR 133.41 - Flight characteristics requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Flight characteristics requirements. 133.41... EXTERNAL-LOAD OPERATIONS Airworthiness Requirements § 133.41 Flight characteristics requirements. (a) The applicant must demonstrate to the Administrator, by performing the operational flight checks prescribed in...

14 CFR 133.41 - Flight characteristics requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Flight characteristics requirements. 133.41... EXTERNAL-LOAD OPERATIONS Airworthiness Requirements § 133.41 Flight characteristics requirements. (a) The applicant must demonstrate to the Administrator, by performing the operational flight checks prescribed in...

49 CFR 234.205 - Operating characteristics of warning system apparatus.

Code of Federal Regulations, 2010 CFR

2010-10-01

... apparatus. 234.205 Section 234.205 Transportation Other Regulations Relating to Transportation (Continued... characteristics of warning system apparatus. Operating characteristics of electromagnetic, electronic, or electrical apparatus of each highway-rail crossing warning system shall be maintained in accordance with the...

49 CFR 234.205 - Operating characteristics of warning system apparatus.

Code of Federal Regulations, 2011 CFR

2011-10-01

... apparatus. 234.205 Section 234.205 Transportation Other Regulations Relating to Transportation (Continued... characteristics of warning system apparatus. Operating characteristics of electromagnetic, electronic, or electrical apparatus of each highway-rail crossing warning system shall be maintained in accordance with the...

Effects of Selected Task Performance Criteria at Initiating Adaptive Task Real locations

NASA Technical Reports Server (NTRS)

Montgomery, Demaris A.

2001-01-01

In the current report various performance assessment methods used to initiate mode transfers between manual control and automation for adaptive task reallocation were tested. Participants monitored two secondary tasks for critical events while actively controlling a process in a fictional system. One of the secondary monitoring tasks could be automated whenever operators' performance was below acceptable levels. Automation of the secondary task and transfer of the secondary task back to manual control were either human- or machine-initiated. Human-initiated transfers were based on the operator's assessment of the current task demands while machine-initiated transfers were based on the operators' performance. Different performance assessment methods were tested in two separate experiments.

Pharmacy characteristics associated with the provision of medication management services within an integrated care management program.

PubMed

Smith, Megan G; Shea, Christopher M; Brown, Patrick; Wines, Kristen; Farley, Joel F; Ferreri, Stefanie P

To examine pharmacy operational and personnel characteristics that influence engagement in providing a community pharmacy medication management service within a statewide integrated care management program. Before the program launch, all of the pharmacies were surveyed to collect demographic, operational, and personnel characteristics such as weekly prescription volume and number of staff, respectively. Those data were then compared with engagement in the program. Engagement was defined as providing initial comprehensive medication review as part of the medication management service. Three months after program launch, pharmacies were dichotomized as consistently engaged or inconsistently engaged. Data were analyzed with the use of descriptive statistics and chi-square and t tests to test for statistical significance between consistent and inconsistent engagement groups. A baseline survey was collected for all 123 pharmacies who joined the integrated care management program. After the first 3 months, 50 pharmacies were consistently engaged in the program. Compared with inconsistently engaged pharmacies, consistently engaged pharmacies employed more full-time pharmacists (mean 2.1 vs. 1.8; P = 0.05) and more full-time technicians (mean 4.0 vs. 3.0; P <0.01), allocated more nondispensing hours for pharmacists (88% vs 60%; P <0.01), were more likely to employ a dedicated clinical pharmacist (20% vs 5%; P = 0.013), and hosted more pharmacy residents (78% vs 22%; P = 0.02). Years of pharmacy operation (P = 0.05) and pharmacy store type (P = 0.05) also were significantly associated with level of engagement. Neither prescription volume dispensed per week, number of hours of pharmacist overlap, nor hosting pharmacy students was statistically different between consistent and inconsistent pharmacies. Engagement in clinical activities in community pharmacy appears to improve with adequate staffing, availability of time for nondispensing activities, and having 1 or more pharmacists dedicated to clinical activities. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

49 CFR 236.8 - Operating characteristics of electromagnetic, electronic, or electrical apparatus.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Operating characteristics of electromagnetic, electronic, or electrical apparatus. 236.8 Section 236.8 Transportation Other Regulations Relating to... characteristics of electromagnetic, electronic, or electrical apparatus. Signal apparatus, the functioning of...

49 CFR 236.8 - Operating characteristics of electromagnetic, electronic, or electrical apparatus.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Operating characteristics of electromagnetic, electronic, or electrical apparatus. 236.8 Section 236.8 Transportation Other Regulations Relating to... characteristics of electromagnetic, electronic, or electrical apparatus. Signal apparatus, the functioning of...

49 CFR 236.8 - Operating characteristics of electromagnetic, electronic, or electrical apparatus.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Operating characteristics of electromagnetic, electronic, or electrical apparatus. 236.8 Section 236.8 Transportation Other Regulations Relating to... characteristics of electromagnetic, electronic, or electrical apparatus. Signal apparatus, the functioning of...

49 CFR 236.8 - Operating characteristics of electromagnetic, electronic, or electrical apparatus.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Operating characteristics of electromagnetic, electronic, or electrical apparatus. 236.8 Section 236.8 Transportation Other Regulations Relating to... characteristics of electromagnetic, electronic, or electrical apparatus. Signal apparatus, the functioning of...

49 CFR 236.8 - Operating characteristics of electromagnetic, electronic, or electrical apparatus.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Operating characteristics of electromagnetic, electronic, or electrical apparatus. 236.8 Section 236.8 Transportation Other Regulations Relating to... characteristics of electromagnetic, electronic, or electrical apparatus. Signal apparatus, the functioning of...

Evaluation of the Missouri WIC (Special Supplemental Nutrition Program for Women, Infants, and Children) breast-feeding peer counselling programme.

PubMed

Yun, Shumei; Liu, Qian; Mertzlufft, Kathy; Kruse, Catherine; White, Maggie; Fuller, Phyllis; Zhu, Bao-Ping

2010-02-01

To evaluate the effectiveness of the peer counselling (PC) programme on breast-feeding initiation among participants in the Special Supplemental Nutrition Program for Women, Infants, and Children (WIC) in Missouri, and to identify factors that facilitate breast-feeding initiation. We used the data from the 2006 Missouri Pregnancy Nutrition Surveillance System, Missouri Live Birth Records and the Missouri WIC programme to compare breast-feeding initiation rates between PC and non-PC agencies. We used multilevel logistic regression, with individual participants being nested within agencies, to control for individual- and agency-level characteristics. The breast-feeding initiation rate in PC agencies was significantly higher than in non-PC agencies among prenatal participants, but the difference was not significant among postpartum participants. After controlling for maternal sociodemographic characteristics, compared with prenatal cases in non-PC agencies, prenatal cases in PC agencies were more likely to initiate breast-feeding (OR = 1.21; 95 % CI 1.03, 1.43), whereas postpartum cases were less likely to initiate breast-feeding. Among prenatal participants in PC agencies, longer duration of prenatal WIC enrolment was associated with a higher rate of breast-feeding initiation. After adjusting for maternal sociodemographic characteristics and other agency-level characteristics, participants of PC agencies with an international board-certified lactation consultant were more likely to initiate breast-feeding than participants of PC agencies without such a consultant (OR = 1.21; 95 % CI 1.01, 1.45). Prenatal participation in the WIC breast-feeding PC programme (especially participation early during pregnancy) was associated with an increased rate of breast-feeding initiation in Missouri.

Learning neuroendoscopy with an exoscope system (video telescopic operating monitor): Early clinical results.

PubMed

Parihar, Vijay; Yadav, Y R; Kher, Yatin; Ratre, Shailendra; Sethi, Ashish; Sharma, Dhananjaya

2016-01-01

Steep learning curve is found initially in pure endoscopic procedures. Video telescopic operating monitor (VITOM) is an advance in rigid-lens telescope systems provides an alternative method for learning basics of neuroendoscopy with the help of the familiar principle of microneurosurgery. The aim was to evaluate the clinical utility of VITOM as a learning tool for neuroendoscopy. Video telescopic operating monitor was used 39 cranial and spinal procedures and its utility as a tool for minimally invasive neurosurgery and neuroendoscopy for initial learning curve was studied. Video telescopic operating monitor was used in 25 cranial and 14 spinal procedures. Image quality is comparable to endoscope and microscope. Surgeons comfort improved with VITOM. Frequent repositioning of scope holder and lack of stereopsis is initial limiting factor was compensated for with repeated procedures. Video telescopic operating monitor is found useful to reduce initial learning curve of neuroendoscopy.

The impact of the uncertainty in the initial soil moisture condition of irrigated areas on the spatiotemporal characteristics of convective activity in Central Greece

NASA Astrophysics Data System (ADS)

Kotsopoulos, Stylianos; Ioannis, Tegoulias; Ioannis, Pytharoulis; Stergios, Kartsios; Dimitrios, Bampzelis; Theodore, Karacostas

2015-04-01

The region of Thessaly is the second largest plain in Greece and has a vital role in the financial life of the country, because of its significant agricultural production. The intensive and extensive cultivation of irrigated crops, in combination with the population increase and the alteration of precipitation patterns due to climate change, often leading the region to experience severe drought conditions, especially during the warm period of the year. The aim of the DAPHNE project is to tackle the problem of drought in this area by means of Weather Modification.In the framework of the project DAPHNE, the numerical weather prediction model WRF-ARW 3.5.1 is used to provide operational forecasts and hindcasts for the region of Thessaly. The goal of this study is to investigate the impact of the uncertainty in the initial soil moisture condition of irrigated areas, on the spatiotemporal characteristics of convective activity in the region of interest. To this end, six cases under the six most frequent synoptic conditions, which are associated with convective activity in the region of interest, are utilized, considering six different soil moisture initialization scenarios. In the first scenario (Control Run), the model is initialized with the surface soil moisture of the ECMWF analysis data, that usually does not take into account the modification of soil moisture due to agricultural activity in the area of interest. In the other five scenarios (Experiment 1,2,3,4,5) the soil moisture in the upper soil layers of the study area are modified from -50% to 50% of field capacity (-50%FC, -25%FC, FC, 25%FC, 50%FC),for the irrigated cropland.Three model domains, covering Europe, the Mediterranean Sea and northern Africa (d01), the wider area of Greece (d02) and central Greece - Thessaly region (d03) are used at horizontal grid-spacings of 15km, 5km and 1km respectively. ECMWF operational analyses at 6-hourly intervals (0.25ox0.25o lat.-long.) are imported as initial and boundary conditions of the coarse domain, while in the vertical, all nests employ 39 sigma levels (up to 50 hPa) with increased resolution in the boundary layer. Microphysical processes are represented by WSM6 scheme, sub-grid scale convection by Kain-Fritsch scheme, longwave and shortwave radiation by RRTMG scheme, surface layer by Monin-Obukhov (MM5), boundary layer by Yonsei University and soil surface scheme by NOAH Unified model. The model numerical results are evaluated against surface precipitation data and data obtained using a C-band (5cm) weather radar located in the centre of the innermost domain. Acknowledgements: This research is co-financed by the European Union (European Regional Development Fund) and Greek national funds, through the action "COOPERATION 2011: Partnerships of Production and Research Institutions in Focused Research and Technology Sectors" (contract number 11SYN_8_1088 - DAPHNE) in the framework of the operational programme "Competitiveness and Entrepreneurship" and Regions in Transition (OPC II, NSRF 2007-2013).

Tropical Cyclone Reconnaissance with the Global Hawk: Operational Thresholds and Characteristics of Convective Systems Over the Tropical Western North Pacific

DTIC Science & Technology

2013-12-01

Tropical cyclone research is an intense ongoing science that has acquired even greater importance in this era of global climate change . Increased study of...RECONNAISSANCE WITH THE GLOBAL HAWK: OPERATIONAL THRESHOLDS AND CHARACTERISTICS OF CONVECTIVE SYSTEMS OVER THE TROPICAL WESTERN NORTH PACIFIC by...TROPICAL CYCLONE RECONNAISSANCE WITH THE GLOBAL HAWK: OPERATIONAL THRESHOLDS AND CHARACTERISTICS OF CONVECTIVE SYSTEMS OVER THE TROPICAL WESTERN

Connecting Coronal Mass Ejections to Their Solar Active Region Sources: Combining Results from the HELCATS and FLARECAST Projects

NASA Astrophysics Data System (ADS)

Murray, Sophie A.; Guerra, Jordan A.; Zucca, Pietro; Park, Sung-Hong; Carley, Eoin P.; Gallagher, Peter T.; Vilmer, Nicole; Bothmer, Volker

2018-04-01

Coronal mass ejections (CMEs) and other solar eruptive phenomena can be physically linked by combining data from a multitude of ground-based and space-based instruments alongside models; however, this can be challenging for automated operational systems. The EU Framework Package 7 HELCATS project provides catalogues of CME observations and properties from the Heliospheric Imagers on board the two NASA/STEREO spacecraft in order to track the evolution of CMEs in the inner heliosphere. From the main HICAT catalogue of over 2,000 CME detections, an automated algorithm has been developed to connect the CMEs observed by STEREO to any corresponding solar flares and active-region (AR) sources on the solar surface. CME kinematic properties, such as speed and angular width, are compared with AR magnetic field properties, such as magnetic flux, area, and neutral line characteristics. The resulting LOWCAT catalogue is also compared to the extensive AR property database created by the EU Horizon 2020 FLARECAST project, which provides more complex magnetic field parameters derived from vector magnetograms. Initial statistical analysis has been undertaken on the new data to provide insight into the link between flare and CME events, and characteristics of eruptive ARs. Warning thresholds determined from analysis of the evolution of these parameters is shown to be a useful output for operational space weather purposes. Parameters of particular interest for further analysis include total unsigned flux, vertical current, and current helicity. The automated method developed to create the LOWCAT catalogue may also be useful for future efforts to develop operational CME forecasting.

Fuel-conservative guidance system for powered-lift aircraft

NASA Technical Reports Server (NTRS)

Erzberger, H.; Mclean, J. D.

1979-01-01

A concept for automatic terminal-area guidance, comprising two modes of operation, has been developed and evaluated in flight tests. In the first or predictive mode, fuel-efficient approach trajectories are synthesized in fast time. In the second or tracking mode, the synthesized trajectories are reconstructed and tracked automatically. An energy rate performance model derived from the lift, drag, and propulsion-system characteristics of the aircraft is used in the synthesis algorithm. The method optimizes the trajectory for the initial aircraft position and wind and temperature profiles encountered during each landing approach. The paper describes the design theory and discusses the results of simulations and flight tests using the Augmentor Wing Jet STOL Research Aircraft.

IRE1: ER stress sensor and cell fate executor.

PubMed

Chen, Yani; Brandizzi, Federica

2013-11-01

Cells operate a signaling network termed the unfolded protein response (UPR) to monitor protein-folding capacity in the endoplasmic reticulum (ER). Inositol-requiring enzyme 1 (IRE1) is an ER transmembrane sensor that activates the UPR to maintain the ER and cellular function. Although mammalian IRE1 promotes cell survival, it can initiate apoptosis via decay of antiapoptotic miRNAs. Convergent and divergent IRE1 characteristics between plants and animals underscore its significance in cellular homeostasis. This review provides an updated scenario of the IRE1 signaling model, discusses emerging IRE1 sensing mechanisms, compares IRE1 features among species, and outlines exciting future directions in UPR research. Copyright © 2013 Elsevier Ltd. All rights reserved.

Development and Testing of a Single Frequency Terahertz Imaging System for Breast Cancer Detection

PubMed Central

St. Peter, Benjamin; Yngvesson, Sigfrid; Siqueira, Paul; Kelly, Patrick; Khan, Ashraf; Glick, Stephen; Karellas, Andrew

2013-01-01

The ability to discern malignant from benign tissue in excised human breast specimens in Breast Conservation Surgery (BCS) was evaluated using single frequency terahertz radiation. Terahertz (THz) images of the specimens in reflection mode were obtained by employing a gas laser source and mechanical scanning. The images were correlated with optical histological micrographs of the same specimens, and a mean discrimination of 73% was found for five out of six samples using Receiver Operating Characteristic (ROC) analysis. The system design and characterization is discussed in detail. The initial results are encouraging but further development of the technology and clinical evaluation is needed to evaluate its feasibility in the clinical environment. PMID:25055306

Thermal Environmental Testing of NSTAR Engineering Model Ion Thrusters

NASA Technical Reports Server (NTRS)

Rawlin, Vincent K.; Patterson, Michael J.; Becker, Raymond A.

1999-01-01

NASA's New Millenium program will fly a xenon ion propulsion system on the Deep Space 1 Mission. Tests were conducted under NASA's Solar Electric Propulsion Technology Applications Readiness (NSTAR) Program with 3 different engineering model ion thrusters to determine thruster thermal characteristics over the NSTAR operating range in a variety of thermal environments. A liquid nitrogen-cooled shroud was used to cold-soak the thruster to -120 C. Initial tests were performed prior to a mature spacecraft design. Those results and the final, severe, requirements mandated by the spacecraft led to several changes to the basic thermal design. These changes were incorporated into a final design and tested over a wide range of environmental conditions.

Selection of a surface tension propellant management system for the Viking 75 Orbiter.

NASA Technical Reports Server (NTRS)

Dowdy, M. W.; Debrock, S. C.

1972-01-01

Discussion of the propellant management system requirements derived for the Viking 75 mission, and review of a series of surface tension propellant management system design concepts. The chosen concept is identified and its mission operation described. The ullage bubble and bulk liquid positioning characteristics are presented, along with propellant dynamic considerations entailed by thrust initiation/termination. Pressurization design considerations, required to assure minimum disturbance to the bulk propellant, are introduced as well as those of the tank ullage vent. Design provisions to assure liquid communication between tank ends are discussed. Results of a preliminary design study are presented, including mechanical testing requirements to assure structural integrity, propellant compatibility, and proper installation.

Sequential measurement of conjugate variables as an alternative quantum state tomography.

PubMed

Di Lorenzo, Antonio

2013-01-04

It is shown how it is possible to reconstruct the initial state of a one-dimensional system by sequentially measuring two conjugate variables. The procedure relies on the quasicharacteristic function, the Fourier transform of the Wigner quasiprobability. The proper characteristic function obtained by Fourier transforming the experimentally accessible joint probability of observing "position" then "momentum" (or vice versa) can be expressed as a product of the quasicharacteristic function of the two detectors and that unknown of the quantum system. This allows state reconstruction through the sequence (1) data collection, (2) Fourier transform, (3) algebraic operation, and (4) inverse Fourier transform. The strength of the measurement should be intermediate for the procedure to work.

Docking simulation analysis of range data requirements for the orbital maneuvering vehicle

NASA Technical Reports Server (NTRS)

Micheal, J. D.; Vinz, F. L.

1985-01-01

The results of an initial study are reported assess the controllability of the Orbital Maneuvering Vehicle (OMV) for terminal closure and docking are reported. The vehicle characteristics used in this study are those of the Marshall Space Flight Center (MSFC) baseline OMV which were published with the request for proposals for preliminary design of this vehicle. This simulation was conducted at MSFC using the Target Motion Simulator. The study focused on the OMV manual mode capability to accommodate both stabilized and tumbling target engagements with varying complements of range and range rate data displayed to the OMV operator. Four trained test subjects performed over 400 simulated orbital dockings during this study. A firm requirement for radar during the terminal closure and dock phase of the OMV mission was not established by these simulations. Fifteen pound thrusters recommended in the MSFC baseline design were found to be advantageous for initial rate matching maneuvers with unstabilized targets; however, lower thrust levels were desirable for making the final docking maneuvers.

Gasdynamic Mirror Fusion Propulsion Experiment

NASA Technical Reports Server (NTRS)

Emrich, William J., Jr.; Rodgers, Stephen L. (Technical Monitor)

2001-01-01

Nuclear fusion appears to be the most promising concept for producing extremely high specific impulse rocket engines. One particular fusion concept which seems to be particularly well suited for fusion propulsion applications is the gasdynamic mirror (GDM). This device would operate at much higher plasma densities and with much larger LD ratios than previous mirror machines. Several advantages accrue from such a design. First, the high LA:) ratio minimizes to a large extent certain magnetic curvature effects which lead to plasma instabilities causing a loss of plasma confinement. Second, the high plasma density will result in the plasma behaving much more Re a conventional fluid with a mean free path shorter than the length of the device. This characteristic helps reduce problems associated with "loss cone" microinstabilities. An experimental GDM device is currently being constructed at the NASA Marshall Space Flight Center to provide an initial assessment of the feasibility of this type of propulsion system. Initial experiments are expected to commence in the late fall of 2000.

Direct observation of conductive filament formation in Alq3 based organic resistive memories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Busby, Y., E-mail: yan.busby@unamur.be; Pireaux, J.-J.; Nau, S.

2015-08-21

This work explores resistive switching mechanisms in non-volatile organic memory devices based on tris(8-hydroxyquinolie)aluminum (Alq{sub 3}). Advanced characterization tools are applied to investigate metal diffusion in ITO/Alq{sub 3}/Ag memory device stacks leading to conductive filament formation. The morphology of Alq{sub 3}/Ag layers as a function of the metal evaporation conditions is studied by X-ray reflectivity, while depth profile analysis with X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry is applied to characterize operational memory elements displaying reliable bistable current-voltage characteristics. 3D images of the distribution of silver inside the organic layer clearly point towards the existence of conductive filamentsmore » and allow for the identification of the initial filament formation and inactivation mechanisms during switching of the device. Initial filament formation is suggested to be driven by field assisted diffusion of silver from abundant structures formed during the top electrode evaporation, whereas thermochemical effects lead to local filament inactivation.« less

A platform for exploding wires in different media

NASA Astrophysics Data System (ADS)

Han, Ruoyu; Wu, Jiawei; Qiu, Aici; Zhou, Haibin; Wang, Yanan; Yan, Jiaqi; Ding, Weidong

2017-10-01

A platform SWE-2 used for single wire explosion experiments has been designed, established, and commissioned. This paper describes the design and initial experiments of SWE-2. In summary, two pulsed current sources based on pulse capacitors and spark gaps are adopted to drive sub-microsecond and microsecond time scale wire explosions in a gaseous/liquid medium, respectively. In the initial experiments, a single copper wire was exploded in air, helium, and argon with a 0.1-0.3 MPa ambient pressure as well as tap water with a 283-323 K temperature, 184-11 000 μ S/cm conductivity, or 0.1-0.9 MPa hydrostatic pressure. In addition, the diagnostic system is introduced in detail. Energy deposition, optical emission, and shock wave characteristics are briefly discussed based on experimental results. The platform was demonstrated to operate successfully with a single wire load. These results provide the potential for further applications of this platform, such as plasma-matter interactions, shock wave effects, and reservoir simulations.

The characterization of widespread fatigue damage in fuselage structure

NASA Technical Reports Server (NTRS)

Piascik, Robert S.; Willard, Scott A.; Miller, Matthew

1994-01-01

The characteristics of widespread fatigue damage (WSFD) in fuselage riveted structure were established by detailed nondestructive and destructive examinations of fatigue damage contained in a full size fuselage test article. The objectives of this were to establish an experimental data base for validating emerging WSFD analytical prediction methodology and to identify first order effects that contribute to fatigue crack initiation and growth. Detailed examinations were performed on a test panel containing four bays of a riveted lap splice joint. The panel was removed from a full scale fuselage test article after receiving 60,000 full pressurization cycles. The results of in situ examinations document the progression of fuselage skin fatigue crack growth through crack linkup. Detailed tear down examinations and fractography of the lap splice joint region revealed fatigue crack initiation sites, crack morphology, and crack linkup geometry. From this large data base, distributions of crack size and locations are presented and discussions of operative damage mechanisms are offered.

The characterization of widespread fatigue damage in fuselage structure

NASA Technical Reports Server (NTRS)

Piascik, Robert S.; Willard, Scott A.; Miller, Matthew

1994-01-01

The characteristics of widespread fatigue damage (WSFD) in fuselage riveted structure were established by detailed nondestructive and destructive examinations of fatigue damage contained in a full size fuselage test article. The objectives of this work were to establish an experimental data base for validating emerging WSFD analytical prediction methodology and to identify first order effects that contribute to fatigue crack initiation and growth. Detailed examinations were performed on a test panel containing four bays of a riveted lap splice joint. The panel was removed from a full scale fuselage test article after receiving 60,000 full pressurization cycles. The results of in situ examinations document the progression of fuselage skin fatigue crack growth through crack linkup. Detailed tear down examinations and fractography of the lap splice joint region revealed fatigue crack initiation sites, crack morphology and crack linkup geometry. From this large data base, distributions of crack size and locations are presented and discussions of operative damage mechanisms are offered.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nichols, Teresa A.; Lapsa, Melissa Voss

Oak Ridge National Laboratory (ORNL) is both the largest science and energy laboratory of the US Department of Energy (DOE) and one of the oldest national laboratories still operating at its original site. These characteristics provide the Sustainable Campus Initiative (SCI) both a unique opportunity and a unique challenge to integrate sustainability into facilities and activities. As outlined in this report, SCI is leveraging the outcomes of ORNL’s DOE-sponsored research and development programs to maximize the efficient use of energy and natural resources across ORNL. Wherever possible, ORNL is integrating technical innovations into new and existing facilities, systems, and processesmore » with a widespread approach to achieving Executive Order 13514. ORNL continues to pursue and deploy innovative solutions and initiatives to advance regional, national, and worldwide sustainability and continues to transform its culture and engage employees in supporting sustainability at work, at home, and in the community. Table 1 summarizes ORNL's FY 2013 performance and planned actions to attain future goals. ORNL has achieved numerous successes during FY 2013, which are described in detail throughout this document.« less

Graphical Procedure for Comparing Thermal Death of Bacillus stearothermophilus Spores in Saturated and Superheated Steam

PubMed Central

Shull, James J.; Ernst, Robert R.

1962-01-01

The thermal death curve of dried spores of Bacillus stearothermophilus in saturated steam was characterized by three phases: (i) a sharp initial rise in viable count; (ii) a low rate of death which gradually increased; and (iii) logarithmic death at maximal rate. The first phase was a reflection of inadequate heat activation of the spore population. The second and third phases represented the characteristic thermal death curve of the spores in saturated steam. A jacketed steam sterilizer, equipped with a system for initial evacuation of the chamber, was examined for superheat during normal operation. Measurements of spore inactivation and temperature revealed superheat in surface layers of fabrics being processed in steam at 121 C. The high temperature of the fabric surfaces was attributed to absorption of excess heat energy from superheated steam. The superheated steam was produced at the beginning of the normal sterilizing cycle by transfer of heat from the steam-heated jacket to saturated steam entering the vessel. PMID:13988774

14 CFR 302.211 - Procedures in certificate cases involving initial or continuing fitness.

Code of Federal Regulations, 2012 CFR

2012-01-01

... initial or continuing fitness. 302.211 Section 302.211 Aeronautics and Space OFFICE OF THE SECRETARY... Disposition of Applications § 302.211 Procedures in certificate cases involving initial or continuing fitness... applicant's fitness to operate. Where such applications propose the operation of scheduled service in...

14 CFR 302.211 - Procedures in certificate cases involving initial or continuing fitness.

Code of Federal Regulations, 2014 CFR

2014-01-01

... initial or continuing fitness. 302.211 Section 302.211 Aeronautics and Space OFFICE OF THE SECRETARY... Disposition of Applications § 302.211 Procedures in certificate cases involving initial or continuing fitness... applicant's fitness to operate. Where such applications propose the operation of scheduled service in...

14 CFR 302.211 - Procedures in certificate cases involving initial or continuing fitness.

Code of Federal Regulations, 2013 CFR

2013-01-01

... initial or continuing fitness. 302.211 Section 302.211 Aeronautics and Space OFFICE OF THE SECRETARY... Disposition of Applications § 302.211 Procedures in certificate cases involving initial or continuing fitness... applicant's fitness to operate. Where such applications propose the operation of scheduled service in...

14 CFR 302.211 - Procedures in certificate cases involving initial or continuing fitness.

Code of Federal Regulations, 2010 CFR

2010-01-01

... initial or continuing fitness. 302.211 Section 302.211 Aeronautics and Space OFFICE OF THE SECRETARY... Disposition of Applications § 302.211 Procedures in certificate cases involving initial or continuing fitness... applicant's fitness to operate. Where such applications propose the operation of scheduled service in...

14 CFR 302.211 - Procedures in certificate cases involving initial or continuing fitness.

Code of Federal Regulations, 2011 CFR

2011-01-01

... initial or continuing fitness. 302.211 Section 302.211 Aeronautics and Space OFFICE OF THE SECRETARY... Disposition of Applications § 302.211 Procedures in certificate cases involving initial or continuing fitness... applicant's fitness to operate. Where such applications propose the operation of scheduled service in...

Turbulent flame propagation and combustion in spark ignition engines

NASA Technical Reports Server (NTRS)

Beretta, G. P.; Rashidi, M.; Keck, J. C.

1983-01-01

Pressure measurements synchronized with high-speed motion-picture records of flame propagation have been made in a transparent-piston engine. The data show that the initial expansion speed of the flame front is close to that of a laminar flame. As the flame expands, its speed rapidly accelerates to a quasi-steady value comparable with that of the turbulent velocity fluctuations in the unburned gas. During the quasi-steady propagation phase, a significant fraction of the gas behind the visible front is unburned. Final burnout of the charge may be approximated by an exponential decay in time. The data have been analyzed in a model-independent way to obtain a set of empirical equations for calculating mass burning rates in spark-ignition engines. The burning equations contain three parameters: the laminar burning speed, a characteristic speed (uT), and a characteristic length (lT). The laminar burning speed is known from laboratory measurements. Tentative correlations relating uT and lT to engine geometry and operating variables have been derived from the engine data.

Etching Characteristics of VO2 Thin Films Using Inductively Coupled Cl2/Ar Plasma

NASA Astrophysics Data System (ADS)

Ham, Yong-Hyun; Efremov, Alexander; Min, Nam-Ki; Lee, Hyun Woo; Yun, Sun Jin; Kwon, Kwang-Ho

2009-08-01

A study on both etching characteristics and mechanism of VO2 thin films in the Cl2/Ar inductively coupled plasma was carried. The variable parameters were gas pressure (4-10 mTorr) and input power (400-700 W) at fixed bias power of 150 W and initial mixture composition of 25% Cl2 + 75% Ar. It was found that an increase in both gas pressure and input power results in increasing VO2 etch rate while the etch selectivity over photoresist keeps a near to constant values. Plasma diagnostics by Langmuir probes and zero-dimensional plasma model provided the data on plasma parameters, steady-state densities and fluxes of active species on the etched surface. The model-based analysis of the etch mechanism showed that, for the given ranges of operating conditions, the VO2 etch kinetics corresponds to the transitional regime of ion-assisted chemical reaction and is influenced by both neutral and ion fluxes with a higher sensitivity to the neutral flux.

[Characteristics and follow-up of sterilized women].

PubMed

Molina, R; López, I

1982-02-01

In order to gain insight into the characteristics of sterilized women evaluating at the same time the effects of sterilization, 70 patients who underwent sterilization in an Obstetrics Unit were studied. The clinical records were analyzed and a questionnaire comprising general knowledge, attitudes, and conduct was applied. Women over 30 and with a parity of 4 or more predominated. There was a low frequency of abortions reported but this information is not reliable. The educational level was lower than the average for the Metropolitan Region and pointed to a more precocious initiation in sexual relationships than was found in a previous similar study. Religion proved to be no obstacle for sterilization nor was attendance to church subsequently diminished. A negative moral feeling towards the operation nearly disappeared following surgery. The fear of sexual dissatisfaction in husbands decreased following surgery and a similar effect was seen with regard to negative self-image. There were no changes in marital relations nor in their satisfaction. (author's modified)

Tensile characteristics of metal nanoparticle films on flexible polymer substrates for printed electronics applications.

PubMed

Kim, Sanghyeok; Won, Sejeong; Sim, Gi-Dong; Park, Inkyu; Lee, Soon-Bok

2013-03-01

Metal nanoparticle solutions are widely used for the fabrication of printed electronic devices. The mechanical properties of the solution-processed metal nanoparticle thin films are very important for the robust and reliable operation of printed electronic devices. In this paper, we report the tensile characteristics of silver nanoparticle (Ag NP) thin films on flexible polymer substrates by observing the microstructures and measuring the electrical resistance under tensile strain. The effects of the annealing temperatures and periods of Ag NP thin films on their failure strains are explained with a microstructural investigation. The maximum failure strain for Ag NP thin film was 6.6% after initial sintering at 150 °C for 30 min. Thermal annealing at higher temperatures for longer periods resulted in a reduction of the maximum failure strain, presumably due to higher porosity and larger pore size. We also found that solution-processed Ag NP thin films have lower failure strains than those of electron beam evaporated Ag thin films due to their highly porous film morphologies.

Enhancing speech recognition using improved particle swarm optimization based hidden Markov model.

PubMed

Selvaraj, Lokesh; Ganesan, Balakrishnan

2014-01-01

Enhancing speech recognition is the primary intention of this work. In this paper a novel speech recognition method based on vector quantization and improved particle swarm optimization (IPSO) is suggested. The suggested methodology contains four stages, namely, (i) denoising, (ii) feature mining (iii), vector quantization, and (iv) IPSO based hidden Markov model (HMM) technique (IP-HMM). At first, the speech signals are denoised using median filter. Next, characteristics such as peak, pitch spectrum, Mel frequency Cepstral coefficients (MFCC), mean, standard deviation, and minimum and maximum of the signal are extorted from the denoised signal. Following that, to accomplish the training process, the extracted characteristics are given to genetic algorithm based codebook generation in vector quantization. The initial populations are created by selecting random code vectors from the training set for the codebooks for the genetic algorithm process and IP-HMM helps in doing the recognition. At this point the creativeness will be done in terms of one of the genetic operation crossovers. The proposed speech recognition technique offers 97.14% accuracy.

The development of an augmentor wing jet STOL research aircraft (modified C-8A). Volume 2: Analysis of contractor's flight test

NASA Technical Reports Server (NTRS)

Skavdahl, H.; Patterson, D. H.

1972-01-01

The initial flight test phase of the modified C-8A airplane was conducted. The primary objective of the testing was to establish the basic airworthiness of the research vehicle. This included verification of the structural design and evaluation of the aircraft's systems. Only a minimum amount of performance testing was scheduled; this has been used to provide a preliminary indication of the airplane's performance and flight characteristics for future flight planning. The testing included flutter and loads investigations up to the maximum design speed. The operational characteristics of all systems were assessed including hydraulics, environmental control system, air ducts, the vectoring conical nozzles, and the stability augmentation system (SAS). Approaches to stall were made at three primary flap settings: up, 30 deg and 65 deg, but full stalls were not scheduled. Minimum control speeds and maneuver margins were checked. All takeoffs and landings were conventional, and STOL performance was not scheduled during this phase of the evaluation.

Investigating the kinetics of the enzymatic depolymerization of polygalacturonic acid in continuous UF-membrane reactors.

PubMed

Gallifuoco, Alberto; Cantarella, Maria; Marucci, Mariagrazia

2007-01-01

A stirred tank membrane reactor is used to study the kinetics of polygalacturonic acid (PGA) enzymatic hydrolysis. The reactor operates in semicontinuous configuration: the native biopolymer is loaded at the initial time and the system is continuously fed with the buffer. The effect of retention time (from 101 to 142 min) and membrane molecular weight cutoff (from 1 to 30 kDa) on the rate of permeable oligomers production is investigated. Reaction products are clustered in two different classes, those sized below the membrane cutoff and those above. The reducing power measured in the permeate is used as an estimate of total product concentration. The characteristic breakdown times range from 40 to 100 min. The overall kinetics obeys a first-order law with a characteristic time estimated to 24 min. New mathematical data handling are developed and illustrated using the experimental data obtained. Finally, the body of the experimental results suggests useful indications (reactor productivity, breakdown induction period) for implementing the bioprocess at the industrial scale.

Electrical characteristics of TIG arcs in argon from non-equilibrium modelling and experiment

NASA Astrophysics Data System (ADS)

Baeva, Margarita; Uhrlandt, Dirk; Siewert, Erwan

2016-09-01

Electric arcs are widely used in industrial processes so that a thorough understanding of the arc characteristics is highly important to industrial research and development. TIG welding arcs operated with pointed electrodes made of tungsten, doped with cerium oxide, have been studied in order to analyze in detail the electric field and the arc voltage. Newly developed non-equilibrium model of the arc is based on a complete diffusion treatment of particle fluxes, a generalized form of Ohm's law, and boundary conditions accounting for the space-charge sheaths within the magneto-hydrodynamic approach. Experiments have been carried out for electric currents in the range 5-200 A. The electric arc has been initiated between a WC20 cathode and a water-cooled copper plate placed 0.8 mm from each other. The arc length has been continuously increased by 0.1 mm up to 15 mm and the arc voltage has been simultaneously recorded. Modelling and experimental results will be presented and discussed.

Current Status of the Gasdynamic Mirror Fusion Propulsion Experiment

NASA Technical Reports Server (NTRS)

Emrich, William J., Jr.

2002-01-01

Nuclear fusion appears to be the most promising concept for producing extremely high specific impulse rocket engines. One particular fusion concept which seems to be particularly well suited for fusion propulsion applications is the gasdynamic mirror (GDM). An experimental GDM device has been constructed at the NASA Marshall Space Flight Center to provide an initial assessment of the feasibility of this type of propulsion system. An initial shakedown of the device is currently underway with initial experiments slated to occur in late 2001. This device would operate at much higher plasma densities and with much larger L/D ratios than previous mirror machines. The high L/D ratio minimizes to a large extent certain magnetic curvature effects which lead to plasma instabilities causing a loss of plasma confinement. The high plasma density results in the plasma behaving much more like a conventional fluid with a mean free path shorter than the length of the device. This characteristic helps reduce problems associated with 'loss cone' microinstabilities. The device has been constructed to allow a considerable degree of flexibility in its configuration thus permitting the experiment to grow over time without necessitating a great deal of additional fabrication.

Hybrid Gear Preliminary Results-Application of Composites to Dynamic Mechanical Components

NASA Technical Reports Server (NTRS)

Handschuh, Robert F.; Roberts Gary D.; Sinnamon, R.; Stringer, David B.; Dykas, Brian D.; Kohlman, Lee W.

2012-01-01

Composite spur gears were fabricated and then tested at NASA Glenn Research Center. The composite material served as the web of the gear between the gear teeth and a metallic hub for mounting to the torque-applying shaft. The composite web was bonded only to the inner and outer hexagonal features that were machined from an initially all-metallic aerospace quality spur gear. The Hybrid Gear was tested against an all-steel gear and against a mating Hybrid Gear. As a result of the composite to metal fabrication process used, the concentricity of the gears were reduced from their initial high-precision value. Regardless of the concentricity error, the hybrid gears operated successfully for over 300 million cycles at 10000 rpm and 490 in.*lbs torque. Although the design was not optimized for weight, the composite gears were found to be 20% lighter than the all-steel gears. Free vibration modes and vibration/noise tests were also conduct to compare the vibration and damping characteristic of the Hybrid Gear to all-steel gears. The initial results indicate that this type of hybrid design may have a dramatic effect on drive system weight without sacrificing strength.

Multichannel, Active Low-Pass Filters

NASA Technical Reports Server (NTRS)

Lev, James J.

1989-01-01

Multichannel integrated circuits cascaded to obtain matched characteristics. Gain and phase characteristics of channels of multichannel, multistage, active, low-pass filter matched by making filter of cascaded multichannel integrated-circuit operational amplifiers. Concept takes advantage of inherent equality of electrical characteristics of nominally-identical circuit elements made on same integrated-circuit chip. Characteristics of channels vary identically with changes in temperature. If additional matched channels needed, chips containing more than two operational amplifiers apiece (e.g., commercial quad operational amplifliers) used. Concept applicable to variety of equipment requiring matched gain and phase in multiple channels - radar, test instruments, communication circuits, and equipment for electronic countermeasures.

Determination of knock characteristics in spark ignition engines: an approach based on ensemble empirical mode decomposition

NASA Astrophysics Data System (ADS)

Li, Ning; Yang, Jianguo; Zhou, Rui; Liang, Caiping

2016-04-01

Knock is one of the major constraints to improve the performance and thermal efficiency of spark ignition (SI) engines. It can also result in severe permanent engine damage under certain operating conditions. Based on the ensemble empirical mode decomposition (EEMD), this paper proposes a new approach to determine the knock characteristics in SI engines. By adding a uniformly distributed and finite white Gaussian noise, the EEMD can preserve signal continuity in different scales and therefore alleviates the mode-mixing problem occurring in the classic empirical mode decomposition (EMD). The feasibilities of applying the EEMD to detect the knock signatures of a test SI engine via the pressure signal measured from combustion chamber and the vibration signal measured from cylinder head are investigated. Experimental results show that the EEMD-based method is able to detect the knock signatures from both the pressure signal and vibration signal, even in initial stage of knock. Finally, by comparing the application results with those obtained by short-time Fourier transform (STFT), Wigner-Ville distribution (WVD) and discrete wavelet transform (DWT), the superiority of the EEMD method in determining knock characteristics is demonstrated.

77 FR 55817 - Panther Creek Power Operating, LLC; Supplemental Notice that Initial Market-Based Rate Filing...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-11

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER12-2570-000] Panther Creek Power Operating, LLC; Supplemental Notice that Initial Market-Based Rate Filing Includes Request for... Panther Creek Power Operating, LLC's application for market-based rate authority, with an accompanying...

78 FR 15876 - Activation of Ice Protection

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-13

... procedures in the Airplane Flight Manual for operating in icing conditions must be initiated. (2) Visual cues... procedures in the Airplane Flight Manual for operating in icing conditions must be initiated. (3) If the... operating rules for flight in icing conditions. This document corrects an error in the amendatory language...

40 CFR 61.33 - Stack sampling.

Code of Federal Regulations, 2014 CFR

2014-07-01

... which has an initial startup date preceding February 27, 2014; or (2) Within 90 days of startup in the case of a new source which did not have an initial startup date preceding February 27, 2014. (b) The... relative frequency of operation of different types of processes, operating hours, operating capacities, or...

40 CFR Table 9 to Subpart Wwww of... - Initial Compliance With Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... have demonstrated initial compliance if . . . 1. a new or existing closed molding operation using... adding materials, and materials are recovered after slitting. 2. a new or existing cleaning operation not...-containing materials storage operation keep containers that store HAP-containing materials closed or covered...

Towards an integral computer environment supporting system operations analysis and conceptual design

NASA Technical Reports Server (NTRS)

Barro, E.; Delbufalo, A.; Rossi, F.

1994-01-01

VITROCISET has in house developed a prototype tool named System Dynamic Analysis Environment (SDAE) to support system engineering activities in the initial definition phase of a complex space system. The SDAE goal is to provide powerful means for the definition, analysis, and trade-off of operations and design concepts for the space and ground elements involved in a mission. For this purpose SDAE implements a dedicated modeling methodology based on the integration of different modern (static and dynamic) analysis and simulation techniques. The resulting 'system model' is capable of representing all the operational, functional, and behavioral aspects of the system elements which are part of a mission. The execution of customized model simulations enables: the validation of selected concepts with respect to mission requirements; the in-depth investigation of mission specific operational and/or architectural aspects; and the early assessment of performances required by the system elements to cope with mission constraints and objectives. Due to its characteristics, SDAE is particularly tailored for nonconventional or highly complex systems, which require a great analysis effort in their early definition stages. SDAE runs under PC-Windows and is currently used by VITROCISET system engineering group. This paper describes the SDAE main features, showing some tool output examples.

The role of oxygen in porous molybdenum electrodes for the alkali metal thermoelectric converter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, R.M.; Nagasubramanian, G.; Khanna, S.K.

1986-08-01

The alkali metal thermoelectric converter is a direct energy conversion device, utilizing a high alkali metal activity gradient to generate electrical power. Its operation is based on the unique ion conductive properties of beta''-alumina solid electrolyte. The major barrier to application of this device is identification of an electrode which can maintain optimum power densities for operation times of >10,000h. Thin, porous molybdenum electrodes have shown the best performance characteristics, but show a variety of time dependent phenomena, including eventual degradation to power densities 3-5 times lower than initial values. Several Na-Mo-O compounds, including Na/sub 2/MoO/sub 4/ and Na/sub 2/Mo/submore » 3/O/sub 6/, are formed during AMTEC operation. These compounds may be responsible for enhanced Na transport through Mo electrodes via sodium ion conduction, and eventual performance degradation due to their volatilization and decomposition. No decomposition of beta''-alumina has been observed under simulated AMTEC operating conditions up to 1373 K. In this paper, we present a model for chemical reactions occurring in porous molybdenum electrodes. The model is based on thermochemical and kinetic data, known sodium-molybdenum-oxygen chemistry, x-ray diffraction analysis of molybdenum and molybdenum oxide electrodes, and the electrochemical behavior of the cell.« less

Savannah River bus project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Summers, W.A.

1998-08-01

The H2Fuel Bus is the world`s first hybrid hydrogen electric transit bus. It was developed through a public/private partnership involving several leading technology and industrial organizations in the Southeast, with primary funding and program management provided by the Department of Energy. The primary goals of the project are to gain valuable information on the technical readiness and economic viability of hydrogen buses and to enhance the public awareness and acceptance of emerging hydrogen technologies. The bus has been operated by the transit agency in Augusta, Georgia since April, 1997. It employs a hybrid IC engine/battery/electric drive system, with onboard hydrogenmore » fuel storage based on the use of metal hydrides. Initial operating results have demonstrated an overall energy efficiency (miles per Btu) of twice that of a similar diesel-fueled bus and an operating range twice that of an all-battery powered electric bus. Tailpipe emissions are negligible, with NOx less than 0.2 ppm. Permitting, liability and insurance issues were addressed on the basis of extensive risk assessment and safety analyses, with the inherent safety characteristic of metal hydride storage playing a major role in minimizing these concerns. Future plans for the bus include continued transit operation and use as a national testbed, with potential modifications to demonstrate other hydrogen technologies, including fuel cells.« less

Operation and biasing for single device equivalent to CMOS

DOEpatents

Welch, James D.

2001-01-01

Disclosed are semiconductor devices including at least one junction which is rectifying whether the semiconductor is caused to be N or P-type, by the presence of field induced carriers. In particular, inverting and non-inverting gate voltage channel induced semiconductor single devices with operating characteristics similar to conventional multiple device CMOS systems, which can be operated as modulators, are disclosed as are a non-latching SCR and an approach to blocking parasitic currents. Operation of the gate voltage channel induced semiconductor single devices with operating characteristics similar to multiple device CMOS systems under typical bias schemes is described, and simple demonstrative five mask fabrication procedures for the inverting and non-inverting gate voltage channel induced semiconductor single devices with operating characteristics similar to multiple device CMOS systems are also presented.

Bridging the Gap: Extending the Life of Marine Corps F/A-18 Hornets

DTIC Science & Technology

2011-04-28

Flight Support Team Fatigue Usage Index Full Up System Level High Flight Hours Initial Operational Capability Initial Operational Test and Evaluation...SLMP SRA STOVL TAT TMS T&R TRAP VMFAT WRA Naval Aviation Enterprise Naval Air Systems Command Naval Inventory Control Point Operational ...suggestions for reducing this burden Ia Washingl!ln Headquarters Service, Directorate for Information Operations and Reports, 1215 Jefferson Davis

A comparison of endoscopic localization error rate between operating surgeons and referring endoscopists in colorectal cancer.

PubMed

Azin, Arash; Saleh, Fady; Cleghorn, Michelle; Yuen, Andrew; Jackson, Timothy; Okrainec, Allan; Quereshy, Fayez A

2017-03-01

Colonoscopy for colorectal cancer (CRC) has a localization error rate as high as 21 %. Such errors can have substantial clinical consequences, particularly in laparoscopic surgery. The primary objective of this study was to compare accuracy of tumor localization at initial endoscopy performed by either the operating surgeon or non-operating referring endoscopist. All patients who underwent surgical resection for CRC at a large tertiary academic hospital between January 2006 and August 2014 were identified. The exposure of interest was the initial endoscopist: (1) surgeon who also performed the definitive operation (operating surgeon group); and (2) referring gastroenterologist or general surgeon (referring endoscopist group). The outcome measure was localization error, defined as a difference in at least one anatomic segment between initial endoscopy and final operative location. Multivariate logistic regression was used to explore the association between localization error rate and the initial endoscopist. A total of 557 patients were included in the study; 81 patients in the operating surgeon cohort and 476 patients in the referring endoscopist cohort. Initial diagnostic colonoscopy performed by the operating surgeon compared to referring endoscopist demonstrated statistically significant lower intraoperative localization error rate (1.2 vs. 9.0 %, P = 0.016); shorter mean time from endoscopy to surgery (52.3 vs. 76.4 days, P = 0.015); higher tattoo localization rate (32.1 vs. 21.0 %, P = 0.027); and lower preoperative repeat endoscopy rate (8.6 vs. 40.8 %, P < 0.001). Initial endoscopy performed by the operating surgeon was protective against localization error on both univariate analysis, OR 7.94 (95 % CI 1.08-58.52; P = 0.016), and multivariate analysis, OR 7.97 (95 % CI 1.07-59.38; P = 0.043). This study demonstrates that diagnostic colonoscopies performed by an operating surgeon are independently associated with a lower localization error rate. Further research exploring the factors influencing localization accuracy and why operating surgeons have lower error rates relative to non-operating endoscopists is necessary to understand differences in care.

Operating Characteristics of the Implicit Learning System Supporting Serial Interception Sequence Learning

ERIC Educational Resources Information Center

Sanchez, Daniel J.; Reber, Paul J.

2012-01-01

The memory system that supports implicit perceptual-motor sequence learning relies on brain regions that operate separately from the explicit, medial temporal lobe memory system. The implicit learning system therefore likely has distinct operating characteristics and information processing constraints. To attempt to identify the limits of the…

Space shuttle orbit maneuvering engine

NASA Technical Reports Server (NTRS)

Pauckert, R. P.

1975-01-01

Data on the performance, stability, and thermal characteristics of an OME operating with an alternate injector configuration and with alternate propellants was obtained. The design, manufacturing, and operating characteristics of an electroformed, regeneratively cooled thrust chamber were also derived. Subscale and full scale tests provide data relating to off-design and transient operation.

Lean, premixed, prevaporized fuel combustor conceptual design study

NASA Technical Reports Server (NTRS)

Fiorentino, A. J.; Greene, W.; Kim, J.

1979-01-01

Four combustor concepts, designed for the energy efficient engine, utilize variable geometry or other flow modulation techniques to control the equivalence ratio of the initial burning zone. Lean conditions are maintained at high power to control oxides of nitrogen while near stoichometric conditions are maintained at low power for low CO and THC emissions. Each concept was analyzed and ranked for its potential in meeting the goals of the program. Although the primary goal of the program is a low level of nitric oxide emissions at stratospheric cruise conditions, both the ground level EPA emission standards and combustor performance and operational requirements typical of advanced subsonic aircraft engines are retained as goals as well. Based on the analytical projections made, two of the concepts offer the potential of achieving the emission goals; however, the projected operational characteristics and reliability of any concept to perform satisfactorily over an entire aircraft flight envelope would require extensive experimental substantiation before engine adaptation can be considered.

Research on electricity market operation mechanism and its benefit of demand side participation

NASA Astrophysics Data System (ADS)

Han, Shuai; Yan, Xu; Qin, Li-juan; Lin, Xi-qiao; Zeng, Bo

2017-08-01

Demand response plays an important role in maintaining the economic stability of the system, and has the characteristics of high efficiency, low cost, fast response, good environmental benefits and so on. Demand side resource is an important part of electricity market. The research of demand side resources in our country is still in the initial stage, but the opening of the electricity sales side provides a broad prospect for the development of electricity market. This paper summarizes the main types of demand side resources in our country, analyzes the economic principle of demand response from the micro perspective, puts forward some suggestions on the operation mechanism of China’s demand side resources participating in the electricity market under the condition of electricity sales side opening, analyzes the current situation of pricing in the electricity wholesale market and sets up the pricing strategy of the centralized wholesale market with the demand side power supply participating in quotation, which makes the social and economic benefits reach the maximum.

First Results from the Cornell COBRA Accelerator for Light Ion ICF Research

NASA Astrophysics Data System (ADS)

Lindholm, F.; Krastelev, E. G.; Greenly, J. B.; Kusse, B. R.

1996-11-01

COBRA, the Cornell Beam Research Accelerator, is a four-stage linear induction adder based on the Sandia National Laboratories SABRE accelerator design. The full 4 × 1 MV, 200 kA, 40 ns COBRA was completed in June 1996, after a year of initial operation with a single stage. Accelerator operation will be described, and first experimental results of power coupling and ion beam generation using a closely-coupled (short MITL) applied-B extraction ion diode load will be presented. A diagnostic package for beam optics including local microdivergence and aiming measurements is being developed, and results from both the single-stage experiments and new experiments on the full accelerator will be presented. A 20 ns, 15% voltage precursor to the main pulse resulting from coupling through the nonlinear magnetization characteristic of the Metglas^circR core at high magnetization rate was seen in the single-cell experiments. This mechanism will be discussed and its consequences on the full accelerator will be investigated.

Chemical, physical, biochemical, and bacteriological characteristics at selected stream sites in Puerto Rico, 1976-77

USGS Publications Warehouse

Quinones, F.; Vasquez, Pedro; Pena-Cortes, Rafael

1978-01-01

In 1969, the Caribbean District of the U.S. Geological Survey, in cooperation with the Commonwealth of Puerto Rico, initiated the operation of a network to monitor some parameters indicative of water-quality changes at selected stream sites. In 1974, at the request of the Environmental Quality Board of Puerto Rico, the network was modified to conform with the Environmental Protection Agency National Water Quality Surveillance System. The purpose of the present network is to monitor changes in water quality between the upstream and downstream stations. The expanded network consisted of 58 stations. During 1976, five had been discontinued. One other was added late in 1976. Most of the stations in the original network have been maintained, thus providing some degree of continuity. The monitoring stations used in this report are shown on a map and listed in a table. The results of the network operation are summarized for the period July 1976 to August 1977. (Woodard-USGS)

Cerenkov Radiator Driven by a Superconducting RF Electron Gun

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poole, B R; Harris, J R

2011-03-07

The Naval Postgraduate School (NPS), Niowave, Inc., and Boeing have recently demonstrated operation of the first superconducting RF electron gun based on a quarter wave resonator structure. In preliminary tests, this gun has produced 10 ps long bunches with charge in excess of 78 pC, and with beam energy up to 396 keV. Initial testing occurred at Niowave's Lansing, MI facility, but the gun and diagnostic beam line are planned for installation in California in the near future. The design of the diagnostic beam line is conducive to the addition of a Cerenkov radiator without interfering with other beam linemore » operations. Design and simulations of a Cerenkov radiator, consisting of a dielectric lined waveguide will be presented. The dispersion relation for the structure is determined and the beam interaction is studied using numerical simulations. The characteristics of the microwave radiation produced in both the short and long bunch regimes will be presented.« less

Friction evaluation of unpaved, gypsum-surface runways at Northrup Strip, White Sands Missile Range, in support of Space Shuttle Orbiter landing and retrieval operations

NASA Technical Reports Server (NTRS)

Yager, T. J.; Horne, W. B.

1980-01-01

Friction measurement results obtained on the gypsum surface runways at Northrup Strip, White Sands Missile Range, N. M., using an instrumented tire test vehicle and a diagonal braked vehicle, are presented. These runways were prepared to serve as backup landing and retrieval sites to the primary sites located at Dryden Flight Research Center for shuttle orbiter during initial test flights. Similar friction data obtained on paved and other unpaved surfaces was shown for comparison and to indicate that the friction capability measured on the dry gypsum surface runways is sufficient for operations with the shuttle orbiter and the Boeing 747 aircraft. Based on these ground vehicle friction measurements, estimates of shuttle orbiter and aircraft tire friction performance are presented and discussed. General observations concerning the gypsum surface characteristics are also included and several recommendations are made for improving and maintaining adequate surface friction capabilities prior to the first shuttle orbiter landing.

Effects of electrolysis by low-amperage electric current on the chlorophyll fluorescence characteristics of Microcystis aeruginosa.

PubMed

Lin, Li; Feng, Cong; Li, Qingyun; Wu, Min; Zhao, Liangyuan

2015-10-01

Effects of electrolysis by low-amperage electric current on the chlorophyll fluorescence characteristics of Microcystis aeruginosa were investigated in order to reveal the mechanisms of electrolytic inhibition of algae. Threshold of current density was found under a certain initial no. of algae cell. When current density was equal to or higher than the threshold (fixed electrolysis time), growth of algae was inhibited completely and the algae lost the ability to survive. Effect of algal solution volume on algal inhibition was insignificant. Thresholds of current density were 8, 10, 14, 20, and 22 mA cm(-2) at 2.5 × 10(7), 5 × 10(7), 1 × 10(8), 2.5 × 10(8), and 5 × 10(8) cells mL(-1) initial no. of algae cell, respectively. Correlativity between threshold of current and initial no. of algae cells was established for scale-up and determining operating conditions. Changes of chlorophyll fluorescence parameters demonstrated that photosystem (PS) II of algae was damaged by electrolysis but still maintained relatively high activity when algal solution was treated by current densities lower than the threshold. The activity of algae recovered completely after 6 days of cultivation. On the contrary, when current density was higher than the threshold, connection of phycobilisome (PBS) and PS II core complexes was destroyed, PS II system of algae was damaged irreversibly, and algae could not survive thoroughly. The inactivation of M. aeruginosa by electrolysis can be attributed to irreversible separation of PBS from PS II core complexes and the damage of PS II of M. aeruginosa.

Recurrent Cubital Tunnel Syndrome Caused by Ganglion: A Report of Nine Cases.

PubMed

Komatsu, Masatoshi; Uchiyama, Shigeharu; Kimura, Takumi; Suenaga, Naoki; Hayashi, Masanori; Kato, Hiroyuki

2018-06-01

Cubital tunnel syndrome (CuTS) is generally treated successfully by surgery and recurrent cases are rare. This study retrospectively investigated the clinical characteristics of recurrent CuTS caused by ganglion. We evaluated nine patients who were surgically treated for recurrent CuTS caused by ganglion. Age distribution at recurrence ranged from 43 to 79 years. The initial surgery for CuTS had been performed using various methods. The asymptomatic period from initial surgery to recurrence ranged from 22 to 252 months. Clinical, diagnostic imaging, and operative findings during the second surgery were analyzed. All patients were treated by anterior subcutaneous ulnar nerve transposition with ganglion resection and later examined directly within a mean of 71 months after the second surgery. The interval from recurrence to consultation was shorter than two months for eight cases. Chief complaints included numbness with or without pain in the ring and little fingers in all patients and resting pain in the medial elbow in five patients. Elbow osteoarthritis was present in all cases. Although four of 10 ganglia were palpable, ultrasonography and magnetic resonance imaging could identify all ganglia preoperatively. The ulnar nerve typically had become entrapped by the ganglion posteriorly and by fascia, scar tissue, and/or muscle anteriorly. Chief complaints and ulnar nerve function were improved in all patients following revision surgery. The acute onset of numbness with or without intolerable pain in the ring and little fingers after a long-term remission period following initial surgery for CuTS in patients with elbow osteoarthritis appears to be the characteristic clinical profile of recurrent CuTS caused by ganglion. As ganglia are often not palpable, ultrasonography and magnetic resonance imaging are recommended for accurate diagnosis.

TMD detection and tracking using improved AWACS sensors

NASA Astrophysics Data System (ADS)

Petersen, Steve; Kinashi, Yasuhiro; Leslie, Daniel

1995-01-01

This paper identifies an UOES (User Operational Evaluation Systems) version of an airborne surveillance sensor funded by the BMDO (Ballistic Missile Defense Organization). The sensors will be integrated into an operational AWACS E-3 upgrade program. This BMDO program initiative is called Extended Airborne Global Launch Evaluator, or EAGLE. Initial Operational Capability (IOC) of the EAGLE system will be ready in time to support the THAAD/GBR UOES capability. This airborne system, when developed, will consist of a passive infrared surveillance sensor (IRSS) with an active laser-ranger, on board an upgraded AWACS E3 aircraft to operate effectively in the TMD (theater missile defense) mission. The objective for the EAGLE is to field, in a reasonably short time and at a relatively low cost, a cueing sensor capability in regional conflicts to augment the existing space-based surveillance systems. With autonomous surveillance capability to search a wide-sector field, the EAGLE can detect and track boosting TBM's shortly after launch or as they break the clouds. Its passive IR sensor can also detect and track warm hardbody targets. Together with its laser-ranger, it is able to determine, immediately after the booster burn-out, very precise target state vectors that are accurate enough to predict their eventual impact points, to cue fire control radars, and to engage the weapons, if needed. Its primary TMD mission is to provide precise cueing of fire control radars to initiate the active defense weapon systems. Accurate cues from the EAGLE will off load radar resources to enable earlier detection of the targets at longer extended ranges, thereby increasing the interceptor battlespace for potentially more effective defense engagements and opportunities. It can also provide a precise early warning message to enable immediate TBM attack assessment and appropriate selection of defense engagement options by the battle manager. The functions of the sensor suite can be distributed, such that it can be tasked independently to observe the threat intercept, while providing continuous surveillance of new TBM launches, to support the kill assessment function for shoot-look-shoot opportunities. Another potential function that can be performed by the EAGLE is the estimation of TMD launch points (LPE) for counterforce support. This technical paper provides an expanded discussion of the EAGLE's mission roles, specific system functions, and its detection and tracking performance capability. The paper also addresses the sensor and the laser subsystem design characteristics and operational modes required to accomplish all its functions. Initial analyses indicate that the impact of scattering and absorption of the IR signatures and laser signals will be minimal on the performance of the system. Recent satellite data provides measurement of atmospheric extinction.

Characterization of the upper pouch tracheo-oesophageal fistula in oesophageal atresia.

PubMed

Summerour, Virginia; Stevens, Paul S; Lander, Anthony D; Singh, Michael; Soccorso, Giampiero; Arul, G Suren

2017-02-01

A small proportion of infants with oesophageal atresia (OA) are thought to have a proximal tracheoesophageal fistula (TOF). Failure to recognize these can hamper mobilization of the upper pouch and lead to life-threatening episodes of aspiration once oral feeding starts. We reviewed our experience of upper pouch fistulae to identify characteristic features of proximal TOF. A retrospective review of TOF/OA patient notes and bronchoscopy photographs and videos, identified from our database from 01/01/2006 to 12/31/2015, was performed. Eight (6.1%) infants were identified (M:F 5:3) from a total population of 131 newly diagnosed TOF/OA infants during the period. Their median gestational age was 33 (range 28-39) weeks, and median birth weight was 1647g (range 1100-3400g). Five were initially diagnosed with pure OA and 3 with a distal TOF. All patients underwent rigid bronchoscopy at the initial surgery but only one proximal fistula was identified. The 7 missed proximal fistulae were subsequently found either during on-table oesophagograms for gap assessment (n=2), at the time of thoracotomy when mobilizing the upper pouch (n=3), or during subsequent bronchoscopy for symptoms post OA repair (n=2). Two patients needed a further operation to divide the fistula. Review of the bronchoscopy videos identified four characteristic differences between upper and lower pouch fistulae. Proximal fistulae are found just distal to the vocal cords, are very small, often no more than a pit, do not open and close with ventilation, and are best identified by insufflation of the esophagus. Upper pouch fistulae are relatively easy to miss because of different characteristics compared with H-type or distal fistulae that have not previously been mentioned in the literature. level IV. Copyright © 2016. Published by Elsevier Inc.

Laparoscopy-assisted versus transabdominal reoperation in Hirschprung's disease for residual aganglionosis and transition zone pathology after transanal pull-through.

PubMed

Xia, Xue; Li, Ning; Wei, Jia; Zhang, Wen; Yu, Donghai; Zhu, Tianqi; Feng, Jiexiong

2016-04-01

This study aims to describe laparoscopic reoperation (LSR) and compare its outcomes with transabdominal reoperation (TAR) for treating Hirschsprung's disease (HD). Eighteen patients with HD underwent reoperation for recurring constipation due to residual aganglionosis and transition zone pathology after an initial transanal procedure (LSR, n=10; TAR, n=8). Preoperative, operative and postoperative data were collected through patient follow-ups ranging from 13 to 75months to compare operative characteristics and postoperative outcomes between the two groups. Ten patients underwent laparoscopic reoperation in our institution without major complications. On average, blood loss was significantly lower in the LSR group (mean±standard deviation, 83±32.7mL) than in the TAR group (185±69mL) (P=0.001). The LSR group had a shorter hospitalization time (12±2days) than the TAR group (15±2.1days) (P=0.02). There was no statistically significant difference in incidence of postoperative complications between the two groups. LSR is safe and technically feasible in HD for recurring constipation due to residual aganglionosis and transition zone pathology, when initial transanal procedure fails. Although RA and TZP can be cured by reoperation, great efforts should be made to diminish the necessity of reoperation. Copyright © 2015 Elsevier Inc. All rights reserved.

Characteristics code for shock initiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Partom, Y.

1986-10-01

We developed SHIN, a characteristics code for shock initiation studies. We describe in detail the equations of state, reaction model, rate equations, and numerical difference equations that SHIN incorporates. SHIN uses the previously developed surface burning reaction model which better represents the shock initiation process in TATB, than do bulk reaction models. A large number of computed simulations prove the code is a reliable and efficient tool for shock initiation studies. A parametric study shows the effect on build-up and run distance to detonation of (1) type of boundary condtion, (2) burning velocity curve, (3) shock duration, (4) rise timemore » in ramp loading, (5) initial density (or porosity) of the explosive, (6) initial temperature, and (7) grain size. 29 refs., 65 figs.« less

Approximation Model Building for Reliability & Maintainability Characteristics of Reusable Launch Vehicles

NASA Technical Reports Server (NTRS)

Unal, Resit; Morris, W. Douglas; White, Nancy H.; Lepsch, Roger A.; Brown, Richard W.

2000-01-01

This paper describes the development of parametric models for estimating operational reliability and maintainability (R&M) characteristics for reusable vehicle concepts, based on vehicle size and technology support level. A R&M analysis tool (RMAT) and response surface methods are utilized to build parametric approximation models for rapidly estimating operational R&M characteristics such as mission completion reliability. These models that approximate RMAT, can then be utilized for fast analysis of operational requirements, for lifecycle cost estimating and for multidisciplinary sign optimization.

40 CFR 63.7826 - How do I demonstrate initial compliance with the operation and maintenance requirements that...

Code of Federal Regulations, 2010 CFR

2010-07-01

... preventative maintenance schedule and, as applicable, detailed descriptions of the corrective action procedures... compliance with the operation and maintenance requirements that apply to me? 63.7826 Section 63.7826... Compliance Requirements § 63.7826 How do I demonstrate initial compliance with the operation and maintenance...

Horizontal/Vertical Stock Fund Cost Comparison

DTIC Science & Technology

1974-08-01

units. Installation Supply Division account and other instal- lation operated activities: Self -Service Supply Store, Clothing Initial...installation supply operations are the Self -Service Supply Center, Clothing Sales Store, Central Issue Facility, and Clothing Initial Issue Point. Stock- age...stocks, stocks for installation operated supply activities such as the Self Service Supply Store, Clothing Sales Store and

Dispersive bi-stability in a vertical microcavity-based saturable absorber due to photo-thermal effect and initial phase-detuning

NASA Astrophysics Data System (ADS)

Pradhan, R.; Saha, S.; Datta, P. K.

2013-01-01

Round-trip phase-shifts with intensity of an input signal due to saturable index change and optically induced thermal effects in a vertical cavity semiconductor (quantum wells) saturable absorber (VCSSA) are investigated analytically to observe counter-clockwise bi-stability in transmission mode and clockwise bi-stability in reflection mode. Simultaneous effects of Kerr nonlinearity and cavity heating on resonance wavelength-shift of the VCSSA micro-cavity are investigated. It is found that these bi-stable characteristics are possible to the absorption edge of nonlinear material for long wavelength side operations of low intensity resonance wavelength of the micro-cavity, where dispersion of absorption and refraction are neglected over a small range of optical wavelength tuning (δλ˜10 nm). Simulations are carried out to find out optimized parameters of the device for bi-stable characteristics. Operations are demonstrated for InGaAs/InP quantum wells based VCSSA with low intensity resonance wavelength of 1570 nm. For counter-clockwise bi-stable switching at working wavelength of 1581 nm, an input intensity variation of 0.79IS is required with top (Rt) and back DBR reflectivity (Rb) of 91% and 93%, respectively, where IS represents the absorption saturation intensity of nonlinear medium. Whereas, the clockwise bi-stability occurs at 0.22IS for working wavelength of 1578 nm with Rt of 90% and Rb of 98%, respectively.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mene, Ravindra U.; School of Physical Sciences, Swami Ramanand Teerth Marathwada University, Nanded 431606, M.S.; Mahabole, Megha P.

Highlights: • We report improved gas sensing and dielectric characteristics of Fe ion exchanged HAp films. • Fe doped HAp film shows maximum gas response at relatively lower temperature. • Response and gas uptake capacity of sensors is improved for appropriate amount of Fe ions in HAp matrix. • Fe-HAp films exhibit remarkable improvement in dielectric properties compared to pure HAp. • Fe doped HAp films show significant improvement in gas sensing as well as in dielectric properties. - Abstract: In the present work Fe doped hydroxyapatite (Fe-HAp) thick films has been successfully utilized to improve the gas sensing asmore » well as its dielectric properties. Initially, HAp nano powder is synthesized by chemical precipitation process and later on Fe ions are doped in HAp by ion exchange process. Structural and morphological modifications are observed by means of X-ray diffraction and scanning electron microscopy analysis. The sensing parameters such as operating temperature, response/recovery time and gas uptake capacity are experimentally determined. The Fe-HAp (0.05 M) film shows improved CO and CO{sub 2} gas sensing capacity at lower operating temperature compared to pure HAp. Moreover, variation of dielectric constant and dielectric loss for pure and Fe-HAp thick films are studied as a function of frequency in the range of 10 Hz–1 MHz. The study reveals that Fe doped HAp thick films improve the sensing and dielectric characteristics as compared to pure HAp.« less

Regime-dependence of Impacts of Radar Rainfall Data Assimilation

NASA Astrophysics Data System (ADS)

Craig, G. C.; Keil, C.

2009-04-01

Experience from the first operational trials of assimilation of radar data in kilometre scale numerical weather prediction models (operating without cumulus parameterisation) shows that the positive impact of the radar data on convective precipitation forecasts typically decay within a few hours, although certain cases show much longer impacts. Here the impact time of radar data assimilation is related to characteristics of the meteorological environment. This QPF uncertainty is investigated using an ensemble of 10 forecasts at 2.8 km horizontal resolution based on different initial and boundary conditions from a global forecast ensemble. Control forecasts are compared with forecasts where radar reflectivity data is assimilated using latent heat nudging. Examination of different cases of convection in southern Germany suggests that the forecasts can be separated into two regimes using a convective timescale. Short impact times are associated with short convective timescales that are characteristic of equilibrium convection. In this regime the statistical properties of the convection are constrained by the large-scale forcing, and effects of the radar data are lost within a few hours as the convection rapidly returns to equilibrium. When the convective timescale is large (non-equilibrium conditions), the impact of the radar data is longer since convective systems are triggered by the latent heat nudging and are able to persist for many hours in the very unstable conditions present in these cases.

Characterization of Screen-Printed Organic Electrochemical Transistors to Detect Cations of Different Sizes.

PubMed

Contat-Rodrigo, Laura; Pérez-Fuster, Clara; Lidón-Roger, José Vicente; Bonfiglio, Annalisa; García-Breijo, Eduardo

2016-09-28

A novel screen-printing fabrication method was used to prepare organic electrochemical transistors (OECTs) based on poly(3,4-ethylenedioxythiophene) doped with polysterene sulfonate (PEDOT:PSS). Initially, three types of these screen-printed OECTs with a different channel and gate areas ratio were compared in terms of output characteristics, transfer characteristics, and current modulation in a phosphate buffered saline (PBS) solution. Results confirm that transistors with a gate electrode larger than the channel exhibit higher modulation. OECTs with this geometry were therefore chosen to investigate their ion-sensitive properties in aqueous solutions of cations of different sizes (sodium and rhodamine B). The effect of the gate electrode was additionally studied by comparing these all-PEDOT:PSS transistors with OECTs with the same geometry but with a non-polarizable metal gate (Ag). The operation of the all-PEDOT:PSS OECTs yields a response that is not dependent on a Na⁺ or rhodamine concentration. The weak modulation of these transistors can be explained assuming that PEDOT:PSS behaves like a supercapacitor. In contrast, the operation of Ag-Gate OECTs yields a response that is dependent on ion concentration due to the redox reaction taking place at the gate electrode with Cl - counter-ions. This indicates that, for cation detection, the response is maximized in OECTs with non-polarizable gate electrodes.

Characteristics of a 30-cm thruster operated with small hole accelerator grid ion optics

NASA Technical Reports Server (NTRS)

Vahrenkamp, R. P.

1976-01-01

Small hole accelerator grid ion optical systems have been tested as a possible means of improving 30-cm ion thruster performance. The effects of small hole grids on the critical aspects of thruster operation including discharge chamber performance, doubly-charged ion concentration, effluent beam characteristics, and plasma properties have been evaluated. In general, small hole accelerator grids are beneficial in improving thruster performance while maintaining low double ion ratios. However, extremely small accelerator aperture diameters tend to degrade beam divergence characteristics. A quantitative discussion of these advantages and disadvantages of small hole accelerator grids, as well as resulting variations in thruster operation characteristics, is presented.

Liquid Rocket Booster (LRB) for the Space Transportation System (STS) systems study. Appendix G: LRB for the STS system study level 2 requirements, revision 1

NASA Technical Reports Server (NTRS)

1989-01-01

Requirements are presented for shuttle system definition; performance and design characteristics; shuttle vehicle end item performance and design characteristics; ground operations complex performance and design characteristics; operability and system design and construction standards; and quality control.

User handbook for block IV silicon solar cell modules

NASA Technical Reports Server (NTRS)

Smokler, M. I.

1982-01-01

The essential electrical and mechanical characteristics of block 4 photovoltaic solar cell modules are described. Such module characteristics as power output, nominal operating voltage, current-voltage characteristics, nominal operating cell temperature, and dimensions are tabulated. The limits of the environmental and other stress tests to which the modules are subjected are briefly described.

Study of Civil Markets for Heavy-Lift Airships

NASA Technical Reports Server (NTRS)

Mettam, P. J.; Hansen, D.; Chabot, C.; Byrne, R.

1978-01-01

The civil markets for heavy lift airships (HLAs) were defined by first identifying areas of most likely application. The operational suitability of HLAs for the applications identified were then assessed. The operating economics of HLAs were established and the market size for HLA services estimated by comparing HLA operating and economic characteristics with those of competing modes. The sensitivities of the market size to HLA characteristics were evaluated and the number and sizes of the vehicles required to service the more promising markets were defined. Important characteristics for future HLAs are discussed that were derived from the study of each application, including operational requirements, features enhancing profitability, military compatibility, improved design requirements, approach to entry into service, and institutional implications for design and operation.

NASA aviation safety reporting system

NASA Technical Reports Server (NTRS)

1978-01-01

The study deals with 165 inadvertent operations on or into inappropriate portions of the aircraft areas at controlled airports. Pilot-initiated and controller-initiated incursions are described and discussed. It was found that a majority of the pilot-initiated occurrences involved operation without a clearance; controller-initiated occurrences usually involved failure to maintain assured separation. The factors associated with these occurrences are analyzed. It appears that a major problem in these occurrences is inadequate coordination among the various system participants. Reasons for this, and some possible solutions to various aspects of the problem, are discussed. A sample of reports from pilots and controllers is presented. These relate to undesired occurrences in air transport, general aviation, and air traffic control operations; to ATC coordination problems; and to a recurrent problem in ASRS reports, parachuting operations. A sample of alert bulletins and responses to them is presented.

Defense Enterprise Accounting and Management System (DEAMS) Increment 1 Release 3 Initial Operational Test and Evaluation Report

DTIC Science & Technology

2015-08-01

Initial Operational Test and Evaluation ( IOT &E) and the system’s operational effectiveness, operational suitability, and cybersecurity. The Air Force...Operational Test and Evaluation Center (AFOTEC) conducted the IOT &E between October 1, 2014, and May 29, 2015, at seven bases that included three...at McConnell Air Force Base (AFB), Kansas. Adequacy of IOT &E The IOT &E was adequate and was executed in accordance with the Test and Evaluation

C-Reactive Protein (CRP), Interferon Gamma-Inducible Protein 10 (IP-10), and Lipopolysaccharide (LPS) Are Associated with Risk of Tuberculosis after Initiation of Antiretroviral Therapy in Resource-Limited Settings

PubMed Central

Tenforde, Mark W.; Gupte, Nikhil; Dowdy, David W.; Asmuth, David M.; Balagopal, Ashwin; Pollard, Richard B.; Sugandhavesa, Patcharaphan; Lama, Javier R.; Pillay, Sandy; Cardoso, Sandra W.; Pawar, Jyoti; Santos, Breno; Riviere, Cynthia; Mwelase, Noluthando; Kanyama, Cecilia; Kumwenda, Johnstone; Hakim, James G.; Kumarasamy, Nagalingeswaran; Bollinger, Robert; Semba, Richard D.; Campbell, Thomas B.; Gupta, Amita

2015-01-01

Objective The association between pre-antiretroviral (ART) inflammation and immune activation and risk for incident tuberculosis (TB) after ART initiation among adults is uncertain. Design Nested case-control study (n = 332) within ACTG PEARLS trial of three ART regimens among 1571 HIV-infected, treatment-naïve adults in 9 countries. We compared cases (participants with incident TB diagnosed by 96 weeks) to a random sample of controls (participants who did not develop TB, stratified by country and treatment arm). Methods We measured pre-ART C-reactive protein (CRP), EndoCab IgM, ferritin, interferon gamma (IFN-γ), interleukin 6 (IL-6), interferon gamma-inducible protein 10 (IP-10), lipopolysaccharide (LPS), soluble CD14 (sCD14), tumor necrosis factor alpha (TNF-α), and CD4/DR+/38+ and CD8/DR+/38+ T cells. Markers were defined according to established cutoff definitions when available, 75th percentile of measured values when not, and detectable versus undetectable for LPS. Using logistic regression, we measured associations between biomarkers and incident TB, adjusting for age, sex, study site, treatment arm, baseline CD4 and log10 viral load. We assessed the discriminatory value of biomarkers using receiver operating characteristic (ROC) analysis. Results Seventy-seven persons (4.9%) developed incident TB during follow-up. Elevated baseline CRP (aOR 3.25, 95% CI: 1.55–6.81) and IP-10 (aOR 1.89, 95% CI: 1.05–3.39), detectable plasma LPS (aOR 2.39, 95% CI: 1.13–5.06), and the established TB risk factors anemia and hypoalbuminemia were independently associated with incident TB. In ROC analysis, CRP, albumin, and LPS improved discrimination only modestly for TB risk when added to baseline routine patient characteristics including CD4 count, body mass index, and prior TB. Conclusion Incident TB occurs commonly after ART initiation. Although associated with higher post-ART TB risk, baseline CRP, IP-10, and LPS add limited value to routine patient characteristics in discriminating who develops active TB. Besides determining ideal cutoffs for these biomarkers, additional biomarkers should be sought that predict TB disease in ART initiators. PMID:25719208

Optimizing Hydropower Day-Ahead Scheduling for the Oroville-Thermalito Project

NASA Astrophysics Data System (ADS)

Veselka, T. D.; Mahalik, M.

2012-12-01

Under an award from the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Water Power Program, a team of national laboratories is developing and demonstrating a suite of advanced, integrated analytical tools to assist managers and planners increase hydropower resources while enhancing the environment. As part of the project, Argonne National Laboratory is developing the Conventional Hydropower Energy and Environmental Systems (CHEERS) model to optimize day-ahead scheduling and real-time operations. We will present the application of CHEERS to the Oroville-Thermalito Project located in Northern California. CHEERS will aid California Department of Water Resources (CDWR) schedulers in making decisions about unit commitments and turbine-level operating points using a system-wide approach to increase hydropower efficiency and the value of power generation and ancillary services. The model determines schedules and operations that are constrained by physical limitations, characteristics of plant components, operational preferences, reliability, and environmental considerations. The optimization considers forebay and afterbay implications, interactions between cascaded power plants, turbine efficiency curves and rough zones, and operator preferences. CHEERS simultaneously considers over time the interactions among all CDWR power and water resources, hydropower economics, reservoir storage limitations, and a set of complex environmental constraints for the Thermalito Afterbay and Feather River habitats. Power marketers, day-ahead schedulers, and plant operators provide system configuration and detailed operational data, along with feedback on model design and performance. CHEERS is integrated with CDWR data systems to obtain historic and initial conditions of the system as the basis from which future operations are then optimized. Model results suggest alternative operational regimes that improve the value of CDWR resources to the grid while enhancing the environment and complying with water delivery obligations for non-power uses.

Earth Observing-1 Extended Mission

USGS Publications Warehouse

,

2005-01-01

Since November 2000, the National Aeronautics and Space Administration (NASA) Earth Observing-1 (EO-1) mission has demonstrated the capabilities of a dozen spacecraft sensor and communication innovations. Onboard the EO-1 spacecraft are two land remote sensing instruments. The Advanced Land Imager (ALI) acquires data in spectral bands and at resolutions similar to Landsat. The Hyperion instrument, which is the first civilian spaceborne hyperspectral imager, acquires data in 220 10-nanometer bands covering the visible, near, and shortwave-infrared bands. The initial one-year technology demonstration phase of the mission included a detailed comparison of ALI with the Landsat Enhanced Thematic Mapper Plus (ETM+) instrument. Specifications for the Operational Land Imager (OLI), the planned successor to ETM+, were formulated in part from performance characteristics of ALI. Recognizing the remarkable performance of the satellite's instruments and the exceptional value of the data, the U.S. Geological Survey (USGS) and NASA agreed in December 2001 to share responsibility for operating EO-1. The extended mission continues, on a cost-reimbursable basis, as long as customer sales fully recover flight and ground operations costs. As of May 2005, more than 17,800 scenes from each instrument have been acquired, indexed, archived, and made available to the public.

Site Selection and Deployment Scenarios for Servicing of Deep-Space Observatories

NASA Technical Reports Server (NTRS)

Willenberg, Harvey J.; Fruhwirth, Michael A.; Potter, Seth D.; Leete, Stephen J.; Moe, Rud V.

2001-01-01

The deep-space environment and relative transportation accessibility of the Weak Stability Boundary (WSB) region connecting the Earth-Moon and Sun-Earth libration points makes the Sun-Earth L2 an attractive operating location for future observatories. A summary is presented of key characteristics of future observatories designed to operate in this region. The ability to service observatories that operate within the region around the Lagrange points may greatly enhance their reliability, lifetime, and scientific return. The range of servicing missions might begin with initial deployment, assembly, test, and checkout. Post-assembly servicing missions might also include maintenance and repair, critical fluids resupply, and instrument upgrades. We define the range of servicing missions that can be performed with extravehicular activity, with teleoperated robots, and with autonomous robots. We then describe deployment scenarios that affect payload design. A trade study is summarized of the benefits and risks of alternative servicing sites, including at the International Space Station, at other low-Earth-orbit locations, at the Earth-Moon L1 location, and on-site at the Sun-Earth L2 location. Required technology trades and development issues for observatory servicing at each site, and with each level of autonomy, are summarized.

Development of consistent hazard controls for DOE transuranic waste operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woody, W.J.

2007-07-01

This paper describes the results of a re-engineering initiative undertaken with the Department of Energy's (DOE) Office of Environmental Management (EM) in order to standardize hazard analysis assumptions and methods and resulting safety controls applied to multiple transuranic (TRU) waste operations located across the United States. A wide range of safety controls are historically applied to transuranic waste operations, in spite of the fact that these operations have similar operational characteristics and hazard/accident potential. The re-engineering effort supported the development of a DOE technical standard with specific safety controls designated for accidents postulated during waste container retrieval, staging/storage, venting, onsitemore » movements, and characterization activities. Controls cover preventive and mitigative measures; include both hardware and specific administrative controls; and provide protection to the facility worker, onsite co-located workers and the general public located outside of facility boundaries. The Standard development involved participation from all major DOE sites conducting TRU waste operations. Both safety analysts and operations personnel contributed to the re-engineering effort. Acknowledgment is given in particular to the following individuals who formed a core working group: Brenda Hawks, (DOE Oak Ridge Office), Patrice McEahern (CWI-Idaho), Jofu Mishima (Consultant), Louis Restrepo (Omicron), Jay Mullis (DOE-ORO), Mike Hitchler (WSMS), John Menna (WSMS), Jackie East (WSMS), Terry Foppe (CTAC), Carla Mewhinney (WIPP-SNL), Stephie Jennings (WIPP-LANL), Michael Mikolanis (DOESRS), Kraig Wendt (BBWI-Idaho), Lee Roberts (Fluor Hanford), and Jim Blankenhorn (WSRC). Additional acknowledgment is given to Dae Chung (EM) and Ines Triay (EM) for leadership and management of the re-engineering effort. (authors)« less

Safety, efficiency and learning curves in robotic surgery: a human factors analysis.

PubMed

Catchpole, Ken; Perkins, Colby; Bresee, Catherine; Solnik, M Jonathon; Sherman, Benjamin; Fritch, John; Gross, Bruno; Jagannathan, Samantha; Hakami-Majd, Niv; Avenido, Raymund; Anger, Jennifer T

2016-09-01

Expense, efficiency of use, learning curves, workflow integration and an increased prevalence of serious incidents can all be barriers to adoption. We explored an observational approach and initial diagnostics to enhance total system performance in robotic surgery. Eighty-nine robotic surgical cases were observed in multiple operating rooms using two different surgical robots (the S and Si), across several specialties (Urology, Gynecology, and Cardiac Surgery). The main measures were operative duration and rate of flow disruptions-described as 'deviations from the natural progression of an operation thereby potentially compromising safety or efficiency.' Contextual parameters collected were surgeon experience level and training, type of surgery, the model of robot and patient factors. Observations were conducted across four operative phases (operating room pre-incision; robot docking; main surgical intervention; post-console). A mean of 9.62 flow disruptions per hour (95 % CI 8.78-10.46) were predominantly caused by coordination, communication, equipment and training problems. Operative duration and flow disruption rate varied with surgeon experience (p = 0.039; p < 0.001, respectively), training cases (p = 0.012; p = 0.007) and surgical type (both p < 0.001). Flow disruption rates in some phases were also sensitive to the robot model and patient characteristics. Flow disruption rate is sensitive to system context and generates improvement diagnostics. Complex surgical robotic equipment increases opportunities for technological failures, increases communication requirements for the whole team, and can reduce the ability to maintain vision in the operative field. These data suggest specific opportunities to reduce the training costs and the learning curve.

The performance and decolourization kinetics of O3/H2O2 oxidation of reactive green 19 dye in wastewater

NASA Astrophysics Data System (ADS)

Sabri, S. N.; Abidin, C. Z. A.; Fahmi; Kow, S. H.; Razali, N. A.

2018-03-01

The degradations characteristic of azo dye Reactive Green 19 (RG19) was investigated using advanced oxidation process (AOPs). It was evaluated based on colour and chemical oxygen demand (COD) removal. The effect of operational parameters such as initial dye concentration, initial dosage of hydrogen peroxide (H2O2), contact time, and pH was also being studied. The samples were treated by ozonation (O3) and peroxone O3/H2O2 process. Advanced oxidation processes (AOPs) involve two stages of oxidation; firstly is the formation of strong oxidant and secondly the reaction of organic contaminants in water. In addition, the term advanced oxidation is referring to the processes in which oxidation of organic contaminants occurs primarily through reactions with hydroxyl radicals. There are several analyses that use to determine the efficiency of the treatment process, which are UV-Vis absorption spectra, COD, Fourier Transform Infrared (FT-IR), and pH. The results demonstrated that the ozone oxidation was efficient in decolourization and good in mineralization, based on the reduction of colour and COD. Additionally, results indicate that H2O2 is able to perform better than ozonation in order to decolourize the dye wastewater with 0.5 mL H2O2/L dye dosage of H2O2 at different initial concentration, initial pH, with contact time.

Enlarging the operation range of a centrifugal compressor by cutting vanes based on CFD

NASA Astrophysics Data System (ADS)

Mo, J. T.; Gu, C. H.; Pan, X. H.; Y Zheng, S.

2013-12-01

Many centrifugal compressors are liable to insufficient operation range. The purpose of this paper is to enlarge the operation range of a centrifugal compressor used in turbocharger by cutting vanes. Some numerical works have been done based on CFD. The comparison of the calculated and measured results shows good agreement. The overall performance characteristics of the centrifugal compressor with different cutted vanes are observed and analyzed. The performance characteristic curves show that cutting vanes can increase the operation range by more than 50% with the loss of the highest efficiency limited in 1%. The flow fields are also shown in this paper and related explanations about the change of the performance characteristics curves are given. Shock wave is also detected in the simulation, and some related characteristics are summed up.

Smart roadside initiative : concept of operations.

DOT National Transportation Integrated Search

2015-09-01

The Smart Roadside Initiative (SRI) is one of several USDOT research and development projects intended to improve the efficiency and safety of the Nations roadways by providing for the exchange of important safety and operational information. This...

Smart roadside initiative : concept of operations.

DOT National Transportation Integrated Search

2012-05-01

The Smart Roadside Initiative (SRI) is one of several USDOT research and development projects intended to improve the efficiency and safety of the Nations roadways by providing for the exchange of important safety and operational information. This...

Design and development of green roof substrate to improve runoff water quality: plant growth experiments and adsorption.

PubMed

Vijayaraghavan, K; Raja, Franklin D

2014-10-15

Many studies worldwide have investigated the potential benefits achievable by transforming brown roofs of buildings to green roofs. However, little literature examined the runoff quality/sorption ability of green roofs. As the green roof substrate is the main component to alter the quality of runoff, this investigation raises the possibility of using a mixture of low-cost inorganic materials to develop a green roof substrate. The tested materials include exfoliated vermiculite, expanded perlite, crushed brick and sand along with organic component (coco-peat). Detailed physical and chemical analyses revealed that each of these materials possesses different characteristics and hence a mix of these materials was desirable to develop an optimal green roof substrate. Using factorial design, 18 different substrate mixes were prepared and detailed examination indicated that mix-12 exhibited desirable characteristics of green roof substrate with low bulk density (431 kg/m(3)), high water holding capacity (39.4%), air filled porosity (19.5%), and hydraulic conductivity (4570 mm/h). The substrate mix also provided maximum support to Portulaca grandiflora (380% total biomass increment) over one month of growth. To explore the leaching characteristics and sorption capacity of developed green roof substrate, a down-flow packed column arrangement was employed. High conductivity and total dissolved solids along with light metal ions (Na, K, Ca and Mg) were observed in the leachates during initial stages of column operation; however the concentration of ions ceased during the final stages of operation (600 min). Experiments with metal-spiked deionized water revealed that green roof substrate possess high sorption capacity towards various heavy metal ions (Al, Fe, Cr, Cu, Ni, Pb, Zn and Cd). Thus the developed growth substrate possesses desirable characteristics for green roofs along with high sorption capacity. Copyright © 2014 Elsevier Ltd. All rights reserved.

Association of prospective lower extremity musculoskeletal injury and musculoskeletal, balance, and physiological characteristics in Special Operations Forces.

PubMed

Keenan, Karen A; Wohleber, Meleesa F; Perlsweig, Katherine A; Baldwin, Thomas M; Caviston, Michael; Lovalekar, Mita; Connaboy, Christopher; Nindl, Bradley C; Beals, Kim

2017-11-01

Previous research has examined lower extremity (LE) musculoskeletal injury (MSI) patterns and risk factors in Special Operations Forces (SOF) trainees, conventional military personnel, and athletes; however, it is unclear if SOF have the same patterns/risk factors. This study aimed to determine the association of musculoskeletal, balance, and physiological characteristics with LE MSI in SOF. Cohort study. A total of 726 Air Force (N=140), Navy Sea, Air, and Land (N=301), and Special Warfare Combatant Crewmen (N=285) SOF (age=25.72±4.77years, height=178.34±6.63cm, weight=84.28±9.03kg) participated in laboratory testing, including: LE muscular strength and flexibility; balance; body composition; anaerobic power/capacity; and aerobic capacity. Medical charts were reviewed for LE MSI 365days following laboratory testing. Participants were assigned by injury status and laboratory data stratified by tertile. Chi-square statistics were calculated to determine the frequency of LE MSI across tertiles for each characteristic. There was a significant association between LE MSI and: ankle inversion strength (weaker side: Χ(2)=17.703; stronger side: Χ(2)=18.911; p≤0.001); ankle eversion/inversion strength ratio (lower side: Χ(2)=13.456; higher side: Χ(2)=16.885; p≤0.001); hamstring flexibility (less flexible: Χ(2)=19.930; more flexible Χ(2)=15.185; p≤0.001); gastrocnemius-soleus flexibility (less flexible: Χ(2)=7.889, p=0.019); dynamic balance asymmetry (Χ(2)=7.444, p=0.024); Vestibular and Preference ratios (Χ(2)=9.124, p=0.010 and Χ(2)=6.572, p=0.037, respectively); and aerobic capacity (Χ(2)=13.935, p=0.001). Characteristics associated with LE MSI are unique in SOF. Human performance program initiatives should include efforts to optimize ankle strength and flexibility, maintain moderate hamstring flexibility, expand dynamic balance strategies, and maximize aerobic capacity to reduce LE MSI risk. Copyright © 2017 Sports Medicine Australia. All rights reserved.

Comparison of chain sampling plans with single and double sampling plans

NASA Technical Reports Server (NTRS)

Stephens, K. S.; Dodge, H. F.

1976-01-01

The efficiency of chain sampling is examined through matching of operating characteristics (OC) curves of chain sampling plans (ChSP) with single and double sampling plans. In particular, the operating characteristics of some ChSP-0, 3 and 1, 3 as well as ChSP-0, 4 and 1, 4 are presented, where the number pairs represent the first and the second cumulative acceptance numbers. The fact that the ChSP procedure uses cumulative results from two or more samples and that the parameters can be varied to produce a wide variety of operating characteristics raises the question whether it may be possible for such plans to provide a given protection with less inspection than with single or double sampling plans. The operating ratio values reported illustrate the possibilities of matching single and double sampling plans with ChSP. It is shown that chain sampling plans provide improved efficiency over single and double sampling plans having substantially the same operating characteristics.

The Effect of Initial Irrigation Conditions on Heap Leaching Efficiency

NASA Astrophysics Data System (ADS)

Briseño Arellano, A. D.; Milczarek, M.; Yao, M.; Brusseau, M. L. L.

2017-12-01

Heap leaching is an unsaturated flow metal recovery process, in which mined ore is irrigated with a lixiviant to dissolve metal contained in the ore. The metal is then extracted from solution. Large scale operations involve stacking ore to depths of 6 to 18 meters on pads that may be hundreds of hectares in area. Heterogeneities within the stacked ore can lead to uneven wetting and the formation of preferential flow pathways, which reduces solution contact and lowers metal recovery. Furthermore, mineral dissolution can cause alteration of the porous media structure and loss of ore permeability. Many mine operators believe that slow initial irrigation rates help minimize permeability loss and increase metal recovery rates. However, this phenomenon has not been studied in detail. Experiments were conducted to investigate the effect of varying initial irrigation rates on leach ore stability. These were conducted with large columns (1.5 m high, 0.5 m in diameter) packed with crushed ore samples that are known to have permeability constraints. The columns were highly instrumented to assess potential changes in material properties both spatially and temporally. Water content was measured with three different methods: capacitance soil moisture sensors placed at 20-cm intervals; a neutron probe to periodically log every 30 cm from four different directions; and electrical resistivity sensors to create a 2-dimensional tomography profile of water content over time. Tensiometers were paired with the soil moisture sensors to measure matric suction and characterize moisture retention characteristics. A non-reactive tracer was used to characterize advective-dispersive transport under unsaturated conditions. A dye solution was introduced at the end of each experiment to map preferential pathways. Continuous monitoring of settling at the surface assisted in measuring consolidation and loss in permeability.

Post-operative re-bleeding in patients with hypertensive ICH is closely associated with the CT blend sign.

PubMed

Wu, Guofeng; Shen, Zhengkui; Wang, Likun; Sun, Shujie; Luo, Jinbiao; Mao, Yuanhong

2017-07-06

Intracranial post-operative re-haemorrhage is an important complication in patients with hypertensive intracerebral haemorrhage (ICH). The purpose of the present study was to determine the value of the computed tomography (CT) blend sign in predicting post-operative re-haemorrhage in patients with ICH. A total of 126 patients with ICH were included in the present study. All the patients underwent standard stereotactic minimally invasive surgery(MIS) to remove the ICH within 24 h following admission. There were 41 patients with a blend sign on initial CT and 85 patients without a blend sign on the initial CT. Multivariable logistic regression analyses were performed to assess the relationship between the presence of the blend sign on the non-enhanced admission CT scan and post-operative re-haemorrhage. Post-operative re-haemorrhage occurred in 24 of the 41 patients with the blend sign, and in 9 of the 85 patients without the blend sign. The incidence of re-haemorrhage was significantly different between the groups. The multivariate logistic regression analysis demonstrated that the initial Glasgow coma scale score (p = 0.002) and blend sign (P < 0.00) on the initial CT scan are independent predictors of post-operative re-haemorrhage. The sensitivity, specificity, and positive and negative predictive values of the blend sign for predicting post-operative re-haemorrhage were 72.7, 81.7, 58.5 and 89.4%, respectively. The presence of the blend sign on the initial CT scan is closely associated with post-operative re-haemorrhage in patients with ICH who undergo stereotactic MIS.

U.S.-MEXICO BORDER PROGRAM ARIZONA BORDER STUDY--STANDARD OPERATING PROCEDURE FOR OPERATION AND INITIALIZATION OF THE MAGELLAN GPS SATELLITE NAVIGATOR (UA-F-22.1)

EPA Science Inventory

The purpose of this SOP is to describe the general procedures for the operation and initialization of the Magellan Global Positioning System (GPS) Satellite Navigator. This procedure was followed to ensure consistent data retrieval during the Arizona NHEXAS project and the Borde...

NHEXAS PHASE I ARIZONA STUDY--STANDARD OPERATING PROCEDURE FOR OPERATION AND INITIALIZATION OF THE MAGELLAN GPS SATELLITE NAVIGATOR (UA-F-22.1)

EPA Science Inventory

The purpose of this SOP is to describe the general procedures for the operation and initialization of the Magellan Global Positioning System (GPS) Satellite Navigator. This procedure was followed to ensure consistent data retrieval during the Arizona NHEXAS project and the "Bord...

Application of computer-aided diagnosis (CAD) in MR-mammography (MRM): do we really need whole lesion time curve distribution analysis?

PubMed

Baltzer, Pascal Andreas Thomas; Renz, Diane M; Kullnig, Petra E; Gajda, Mieczyslaw; Camara, Oumar; Kaiser, Werner A

2009-04-01

The identification of the most suspect enhancing part of a lesion is regarded as a major diagnostic criterion in dynamic magnetic resonance mammography. Computer-aided diagnosis (CAD) software allows the semi-automatic analysis of the kinetic characteristics of complete enhancing lesions, providing additional information about lesion vasculature. The diagnostic value of this information has not yet been quantified. Consecutive patients from routine diagnostic studies (1.5 T, 0.1 mmol gadopentetate dimeglumine, dynamic gradient-echo sequences at 1-minute intervals) were analyzed prospectively using CAD. Dynamic sequences were processed and reduced to a parametric map. Curve types were classified by initial signal increase (not significant, intermediate, and strong) and the delayed time course of signal intensity (continuous, plateau, and washout). Lesion enhancement was measured using CAD. The most suspect curve, the curve-type distribution percentage, and combined dynamic data were compared. Statistical analysis included logistic regression analysis and receiver-operating characteristic analysis. Fifty-one patients with 46 malignant and 44 benign lesions were enrolled. On receiver-operating characteristic analysis, the most suspect curve showed diagnostic accuracy of 76.7 +/- 5%. In comparison, the curve-type distribution percentage demonstrated accuracy of 80.2 +/- 4.9%. Combined dynamic data had the highest diagnostic accuracy (84.3 +/- 4.2%). These differences did not achieve statistical significance. With appropriate cutoff values, sensitivity and specificity, respectively, were found to be 80.4% and 72.7% for the most suspect curve, 76.1% and 83.6% for the curve-type distribution percentage, and 78.3% and 84.5% for both parameters. The integration of whole-lesion dynamic data tends to improve specificity. However, no statistical significance backs up this finding.

Role of fuel additives on reduction of NOX emission from a diesel engine powered by camphor oil biofuel.

PubMed

Subramanian, Thiyagarajan; Varuvel, Edwin Geo; Ganapathy, Saravanan; Vedharaj, S; Vallinayagam, R

2018-06-01

The present study intends to explore the effect of the addition of fuel additives with camphor oil (CMO) on the characteristics of a twin-cylinder compression ignition (CI) engine. The lower viscosity and boiling point of CMO when compared to diesel could improve the fuel atomization, evaporation, and air/fuel mixing process. However, the lower cetane index of CMO limits its use as a drop in fuel for diesel in CI engine. In general, NO X emission increases for less viscous and low cetane (LVLC) fuels due to pronounced premixed combustion phase. To improve the ignition characteristics and decrease NO X emissions, fuel additives such as diglyme (DGE)-a cetane enhancer, cumene (CU)-an antioxidant, and eugenol (EU) and acetone (A)-bio-additives, are added 10% by volume with CMO. The engine used for the experimentation is a twin-cylinder tractor engine that runs at a constant speed of 1500 rpm. The engine was operated with diesel initially to attain warm-up condition, which facilitates the operation of neat CMO. At full load condition, brake thermal efficiency (BTE) for CMO is higher (29.6%) than that of diesel (28.1%), while NO X emission is increased by 9.4%. With DGE10 (10% DGE + 90% CMO), the ignition characteristics of CMO are improved and BTE is increased to 31.7% at full load condition. With EU10 (10% EU + 90% CMO) and A10 (10% A + 90% CMO), NO X emission is decreased by 24.6 and 17.8% when compared to diesel, while BTE is comparable to diesel. While HC and CO emission decreased for DGE10 and CU10, they increased for EU10 and A10 when compared to baseline diesel and CMO.

Improved Stratospheric Temperature Retrievals for Climate Reanalysis

NASA Technical Reports Server (NTRS)

Rokke, L.; Joiner, J.

1999-01-01

The Data Assimilation Office (DAO) is embarking on plans to generate a twenty year reanalysis data set of climatic atmospheric variables. One of the focus points will be in the evaluation of the dynamics of the stratosphere. The Stratospheric Sounding Unit (SSU), flown as part of the TIROS Operational Vertical Sounder (TOVS), is one of the primary stratospheric temperature sensors flown consistently throughout the reanalysis period. Seven unique sensors made the measurements over time, with individual instrument characteristics that need to be addressed. The stratospheric temperatures being assimilated across satellite platforms will profoundly impact the reanalysis dynamical fields. To attempt to quantify aspects of instrument and retrieval bias we are carefully collecting and analyzing all available information on the sensors, their instrument anomalies, forward model errors and retrieval biases. For the retrieval of stratospheric temperatures, we adapted the minimum variance approach of Jazwinski (1970) and Rodgers (1976) and applied it to the SSU soundings. In our algorithm, the state vector contains an initial guess of temperature from a model six hour forecast provided by the Goddard EOS Data Assimilation System (GEOS/DAS). This is combined with an a priori covariance matrix, a forward model parameterization, and specifications of instrument noise characteristics. A quasi-Newtonian iteration is used to obtain convergence of the retrieved state to the measurement vector. This algorithm also enables us to analyze and address the systematic errors associated with the unique characteristics of the cell pressures on the individual SSU instruments and the resolving power of the instruments to vertical gradients in the stratosphere. The preliminary results of the improved retrievals and their assimilation as well as baseline calculations of bias and rms error between the NESDIS operational product and col-located ground measurements will be presented.

Configuration and validation of a novel prostate disease nomogram predicting prostate biopsy outcome: A prospective study correlating clinical indicators among Filipino adult males with elevated PSA level.

PubMed

Chua, Michael E; Tanseco, Patrick P; Mendoza, Jonathan S; Castillo, Josefino C; Morales, Marcelino L; Luna, Saturnino L

2015-04-01

To configure and validate a novel prostate disease nomogram providing prostate biopsy outcome probabilities from a prospective study correlating clinical indicators and diagnostic parameters among Filipino adult male with elevated serum total prostate specific antigen (PSA) level. All men with an elevated serum total PSA underwent initial prostate biopsy at our institution from January 2011 to August 2014 were included. Clinical indicators, diagnostic parameters, which include PSA level and PSA-derivatives, were collected as predictive factors for biopsy outcome. Multiple logistic-regression analysis involving a backward elimination selection procedure was used to select independent predictors. A nomogram was developed to calculate the probability of the biopsy outcomes. External validation of the nomogram was performed using separate data set from another center for determination of sensitivity and specificity. A receiver-operating characteristic (ROC) curve was used to assess the accuracy in predicting differential biopsy outcome. Total of 552 patients was included. One hundred and ninety-one (34.6%) patients had benign prostatic hyperplasia, and 165 (29.9%) had chronic prostatitis. The remaining 196 (35.5%) patients had prostate adenocarcinoma. The significant independent variables used to predict biopsy outcome were age, family history of prostate cancer, prior antibiotic intake, PSA level, PSA-density, PSA-velocity, echogenic findings on ultrasound, and DRE status. The areas under the receiver-operating characteristic curve for prostate cancer using PSA alone and the nomogram were 0.688 and 0.804, respectively. The nomogram configured based on routinely available clinical parameters, provides high predictive accuracy with good performance characteristics in predicting the prostate biopsy outcome such as presence of prostate cancer, high Gleason prostate cancer, benign prostatic hyperplasia, and chronic prostatitis.

The development of an evaluation framework for injury surveillance systems

PubMed Central

Mitchell, Rebecca J; Williamson, Ann M; O'Connor, Rod

2009-01-01

Background Access to good quality information from injury surveillance is essential to develop and monitor injury prevention activities. To determine if information obtained from surveillance is of high quality, the limitations and strengths of a surveillance system are often examined. Guidelines have been developed to assist in evaluating certain types of surveillance systems. However, to date, no standard guidelines have been developed to specifically evaluate an injury surveillance system. The aim of this research is to develop a framework to guide the evaluation of injury surveillance systems. Methods The development of an Evaluation Framework for Injury Surveillance Systems (EFISS) involved a four stage process. First, a literature review was conducted to identify an initial set of characteristics that were recognised as important and/or had been recommended to be assessed in an evaluation of a surveillance system. Second, this set of characteristics was assessed using SMART criteria. Third, those surviving were presented to an expert panel using a two round modified-Delphi study to gain an alternative perspective on characteristic definitions, practicality of assessment, and characteristic importance. Finally, a rating system was created for the EFISS characteristics. Results The resulting EFISS consisted of 18 characteristics that assess three areas of an injury surveillance system – five characteristics assess data quality, nine characteristics assess the system's operation, and four characteristics assess the practical capability of an injury surveillance system. A rating system assesses the performance of each characteristic. Conclusion The development of the EFISS builds upon existing evaluation guidelines for surveillance systems and provides a framework tailored to evaluate an injury surveillance system. Ultimately, information obtained through an evaluation of an injury data collection using the EFISS would be useful for agencies to recommend how a collection could be improved to increase its usefulness for injury surveillance and in the long-term injury prevention. PMID:19627617

7 CFR 42.142 - Curve for obtaining Operating Characteristic (OC) curve information for skip lot sampling and...

Code of Federal Regulations, 2010 CFR

2010-01-01

... the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... CONDITION OF FOOD CONTAINERS Miscellaneous § 42.142 Curve for obtaining Operating Characteristic (OC) curve...

Smart roadside initiative gap analysis : target functionality and gap analysis.

DOT National Transportation Integrated Search

2015-02-01

This document summarizes the target functionality for the Smart Roadside Initiative, as well as the operational, institutional, and technical gaps that currently impede the deployment of three of its operational scenarios (electronic mainline s...

Concurrently adjusting interrelated control parameters to achieve optimal engine performance

DOEpatents

Jiang, Li; Lee, Donghoon; Yilmaz, Hakan; Stefanopoulou, Anna

2015-12-01

Methods and systems for real-time engine control optimization are provided. A value of an engine performance variable is determined, a value of a first operating condition and a value of a second operating condition of a vehicle engine are detected, and initial values for a first engine control parameter and a second engine control parameter are determined based on the detected first operating condition and the detected second operating condition. The initial values for the first engine control parameter and the second engine control parameter are adjusted based on the determined value of the engine performance variable to cause the engine performance variable to approach a target engine performance variable. In order to cause the engine performance variable to approach the target engine performance variable, adjusting the initial value for the first engine control parameter necessitates a corresponding adjustment of the initial value for the second engine control parameter.

The operations of quantum logic gates with pure and mixed initial states.

PubMed

Chen, Jun-Liang; Li, Che-Ming; Hwang, Chi-Chuan; Ho, Yi-Hui

2011-04-07

The implementations of quantum logic gates realized by the rovibrational states of a C(12)O(16) molecule in the X((1)Σ(+)) electronic ground state are investigated. Optimal laser fields are obtained by using the modified multitarget optimal theory (MTOCT) which combines the maxima of the cost functional and the fidelity for state and quantum process. The projection operator technique together with modified MTOCT is used to get optimal laser fields. If initial states of the quantum gate are pure states, states at target time approach well to ideal target states. However, if the initial states are mixed states, the target states do not approach well to ideal ones. The process fidelity is introduced to investigate the reliability of the quantum gate operation driven by the optimal laser field. We found that the quantum gates operate reliably whether the initial states are pure or mixed.

Medical malpractice and hernia repair: an analysis of case law.

PubMed

Walters, Amanda L; Dacey, Kristian T; Zemlyak, Alla Y; Lincourt, Amy E; Heniford, B Todd

2013-04-01

Litigation analysis and clinician education are essential to reduce the number and cost of malpractice claims. This study evaluates the clinical characteristics and legal outcomes of medical malpractice litigation initiated by patients having undergone a hernia repair operation. Published civil suits were obtained from a legal database for state and federal decisions constituting case law. The published material includes information on defendants, plaintiffs, allegations, outcomes, and a variety of legal issues. A retrospective review of 44 published cases from 25 states was performed. Complications were present in 20 of 44 (45%) suits, four (9%) of which were because of infection. Death occurred in five (11%) cases, and failure to obtain informed consent was alleged in seven (16%) of the suits. Retained foreign bodies were present in 7 of the 44 (16%) suits. Other allegations included incorrect surgical technique, insufficient need for surgery, and emotional distress. Most (64%) patients initiating malpractice litigation were male, and inguinal, hiatal, and ventral hernia repairs account for 39%, 27%, and 14% of cases, respectively. Most suits (40%) were initiated in Southern states. Surgical mesh was indicated in 5 of 44 (11%) suits but four of five were unrelated to the suit. One patient initiated litigation because of the fact that the surgeon did not use mesh during surgery, which was discussed preoperatively during the informed consent. The court ruled in favor of the plaintiff in 12 of 44 (27%) suits, with compensation ranging from roughly $19,000 to $8,000,000. Louisiana and New York had six and seven suits each, which appears disproportionate given their respective populations. Complications and death resulting from alleged clinical negligence play a significant role in both the initiation and the outcome of malpractice litigation. Retained foreign bodies and lack of informed consent account for roughly one-third of malpractice litigation associated with hernia repairs. Many of these suits may be avoided with proper patient education and documentation of such along with standard operative preventative measures. Copyright © 2013 Elsevier Inc. All rights reserved.

A Pilot Study Using a Web Survey to Identify Characteristics That Influence Hypogonadal Men to Initiate Testosterone Replacement Therapy.

PubMed

Rosen, Raymond C; Seftel, Allen D; Ruff, Dustin D; Muram, David

2018-05-01

Men with hypogonadism (HG) who choose testosterone replacement therapy (TRT) may have distinct characteristics that provide insight as to why they may/may not initiate therapy. The aim of the current study was to identify trends in patient characteristics and attitudes in men diagnosed with HG who initiated TRT (TRT+) compared with men who were diagnosed with HG but did not initiate TRT (TRT-). The market research-based online survey conducted between 2012 and 2013 included patients from a Federated Sample, a commercially available panel of patients with diverse medical conditions. The current analysis was composed of two groups: TRT+ ( n = 155) and TRT- ( n = 157). Patient demographics, clinical characteristics, and attitudes toward HG and TRT were examined as potential predictors of primary adherence in men with HG; cohorts were compared by using Fisher's exact test. Significant associations among sexual orientation, relationship status, educational level, presence of comorbid erectile dysfunction, area of residence, and TRT initiation were present ( p ≤ .05). College-educated, heterosexual, married men with comorbid erectile dysfunction living in suburban and urban areas were more likely to initiate treatment. The most bothersome symptoms reported were lack of energy (90% vs. 81%, p = .075), decreased strength and endurance (86% vs. 76%, p = .077), and deterioration in work performance (52% vs. 31%, p = .004); lack of energy prompted men to seek help. Patients (48%) in the TRT+ group were more knowledgeable regarding HG as compared with TRT- respondents (14%, p < .001), and most men obtained their information from a health care professional (89% vs. 82%, p = .074). The current analysis identified distinct demographic and clinical characteristics and attitudes among TRT users compared with men who were diagnosed with HG yet remained untreated.

Space nuclear power applied to electric propulsion

NASA Technical Reports Server (NTRS)

Vicente, F. A.; Karras, T.; Darooka, D.; Isenberg, L.

1989-01-01

Space reactor power systems with characteristics ideal for advanced spacecraft systems applications are discussed. These characteristics are: high power-to-weight ratio (15 to 33 W/kg); high volume density (high ballistic coefficient); no preferential orientation in orbit; long operational life; high reliability; and total launch and operational safety. These characteristics allow the use of electric propulsion to raise spacecraft from low earth parking orbits to operational orbits, greatly increasing the useful orbit payload for a given launch vehicle by eliminating the need for a separation injection stage. A proposed demonstration mission is described.

Estimation of the Operating Characteristics when the Test Information of the Old Test is not Constant. I. Rationale.

DTIC Science & Technology

1980-06-16

AO-AOB 075 TENNESSEE UNIV KNOXVILLE DIEPT OF PSYCHOLOGY F/G 12/1 AoI FSTIMATION OF THE OPERATING CHARACTERISTICS WHEM THE TEST INFOR--ETCIUI ’JUN... testing . Applied Psychological Measurement, 1, 1977, pages 2 33 -24 7 (a). [121 Samejima, F. Applications of graded response models: The promise of the... PSYCHOLOGY F/S 12/1 FSTIMATION OF THE OPERATING CHARACTERISTICS WHEP- THE TEST INFOR- ETC(U) JUN GO F SAMEJIMA N00014-77-C-0360 UNCLASSIFIED RR-80-2 NL

Investigations on Absorber Materials at Cryogenic Temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marhauser, Frank; Elliott, Thomas; Rimmer, Robert

2009-05-01

In the framework of the 12 GeV upgrade project for the Continuous Electron Beam Accelerator Facility (CEBAF) improvements are being made to refurbish cryomodules housing Thomas Jefferson National Accelerator Facility's (JLab) original 5-cell cavities. Recently we have started to look into a possible simplification of the existing Higher Order Mode (HOM) absorber design combined with the aim to find alternative material candidates. The absorbers are implemented in two HOM-waveguides immersed in the helium bath and operate at 2 K temperature. We have built a cryogenic setup to perform measurements on sample load materials to investigate their lossy characteristics and variationsmore » from room temperature down to 2 K. Initial results are presented in this paper.« less

Delay banking for air traffic management

NASA Technical Reports Server (NTRS)

Green, Steven M. (Inventor)

2007-01-01

A method and associated system for time delay banking for aircraft arrival time, aircraft departure time and/or en route flight position. The delay credit value for a given flight may decrease with passage of time and may be transferred to or traded with other flights having the same or a different user (airline owner or operator). The delay credit value for a given aircraft flight depends upon an initial delay credit value, which is determined by a central system and depends upon one or more other flight characteristics. Optionally, the delay credit value decreases with passage of time. Optionally, a transaction cost is assessed against a delay credit value that is used on behalf of another flight with the same user or is traded with a different user.

Uncertainties in building a strategic defense.

PubMed

Zraket, C A

1987-03-27

Building a strategic defense against nuclear ballistic missiles involves complex and uncertain functional, spatial, and temporal relations. Such a defensive system would evolve and grow over decades. It is too complex, dynamic, and interactive to be fully understood initially by design, analysis, and experiments. Uncertainties exist in the formulation of requirements and in the research and design of a defense architecture that can be implemented incrementally and be fully tested to operate reliably. The analysis and measurement of system survivability, performance, and cost-effectiveness are critical to this process. Similar complexities exist for an adversary's system that would suppress or use countermeasures against a missile defense. Problems and opportunities posed by these relations are described, with emphasis on the unique characteristics and vulnerabilities of space-based systems.

Neutron radiation tolerance of Au-activated silicon

NASA Technical Reports Server (NTRS)

Joyner, W. T.

1987-01-01

Double injection devices prepared by the introduction of deep traps, using the Au activation method have been found to tolerate gamma irradiation into the Gigarad (Si) region without significant degradation of operating characteristics. Silicon double injection devices, using deep levels creacted by Au diffusion, can tolerate fast neutron irradiation up to 10 to the 15th n/sq cm. Significant parameter degradation occurs at 10 to the 16th n/sq cm. However, since the actual doping of the basic material begins to change as a result of the transmutation of silicon into phosphorus for neutron fluences greater than 10 to the 17th/sq cm, the radiation tolerance of these devices is approaching the limit possible for any device based on initially doped silicon.

Introduction of laser initiation for the 48-inch Advanced Solid Rocket Motor (ASRM) test motors at Marshall Space Flight Center (MSFC)

NASA Technical Reports Server (NTRS)

Zimmerman, Chris J.; Litzinger, Gerald E.

1993-01-01

The Advanced Solid Rocket Motor is a new design for the Space Shuttle Solid Rocket Booster. The new design will provide more thrust and more payload capability, as well as incorporating many design improvements in all facets of the design and manufacturing process. A 48-inch (diameter) test motor program is part of the ASRM development program. This program has multiple purposes for testing of propellent, insulation, nozzle characteristics, etc. An overview of the evolution of the 48-inch ASRM test motor ignition system which culminated with the implementation of a laser ignition system is presented. The laser system requirements, development, and operation configuration are reviewed in detail.

A site evaluation campaign for a ground based atmospheric Cherenkov telescope in Romania

NASA Astrophysics Data System (ADS)

Radu, Aurelian Andrei; Angelescu, Tatiana; Curtef, Valentin; Delia, Florin; Felea, Daniel; Goia, Ioana; Haşegan, Dumitru; Lucaschi, Bogdan; Manea, Ancuta; Popa, Vlad; Raliţă, Ioan; Văcăreanu, Radu

2012-07-01

Around the world, several scientific projects share the interest of a global network of small Cherenkov telescopes for monitoring observations of the brightest blazars—the DWARF network. A small, ground based, imaging atmospheric Cherenkov telescope of last generation is intended to be installed and operated in Romania as a component of the DWARF network. To prepare the construction of the observatory, two support projects have been initiated. Within the framework of these projects, we have assessed a number of possible sites where to settle the observatory. In this paper we submit a brief report on the general characteristics of the best four sites selected after the local infrastructure, the nearby facilities and the social impact criteria have been applied.

Smart Cameras for Remote Science Survey

NASA Technical Reports Server (NTRS)

Thompson, David R.; Abbey, William; Allwood, Abigail; Bekker, Dmitriy; Bornstein, Benjamin; Cabrol, Nathalie A.; Castano, Rebecca; Estlin, Tara; Fuchs, Thomas; Wagstaff, Kiri L.

2012-01-01

Communication with remote exploration spacecraft is often intermittent and bandwidth is highly constrained. Future missions could use onboard science data understanding to prioritize downlink of critical features [1], draft summary maps of visited terrain [2], or identify targets of opportunity for followup measurements [3]. We describe a generic approach to classify geologic surfaces for autonomous science operations, suitable for parallelized implementations in FPGA hardware. We map these surfaces with texture channels - distinctive numerical signatures that differentiate properties such as roughness, pavement coatings, regolith characteristics, sedimentary fabrics and differential outcrop weathering. This work describes our basic image analysis approach and reports an initial performance evaluation using surface images from the Mars Exploration Rovers. Future work will incorporate these methods into camera hardware for real-time processing.

Triggering regime of oil-filled trigatron dischargers

NASA Astrophysics Data System (ADS)

Kapishnikov, N. K.; Muratov, V. M.

1986-11-01

A comparative analysis made in [1, 2] of different types of regulable high-voltage dischargers with liquid insulation showed that trigatrons are currently the most promising for use in high-voltage pulse-operated devices due to their simplicity and reliability. Two basic mechanisms of discharge initiation can be realized in trigatrons — initiation by intensification of the field in the region of the control electrode [2, 3], and triggering by a spark in the ignition gap [4, 5]. The first type of trigatron has been studied sufficiently only for short voltage periods [3, 6, 7], so it is used mainly in switching the pulse-shaping lines of powerful nanosecond pulse generators with “rapid” (0.5 1.5 μsec) charging [8, 9]. Almost no use is now made of the second type of trigatron switch in high-voltage pulse technology due to its unsatisfactory time characteristics. Here we report results of a study of the time characteristics of both types of oil-filled trigatrons operating in a regime whereby they form the leading edge of rectangular voltage pulses with amplitudes up to 800 kV and durations of 1 100 μsec. The goal is to find the optimum conditions for triggering of trigatron dischargers with liquid insulation in the region of microsecond voltage discharges. Experiments were conducted on the unit in [10]. The test discharger was placed in a cylindrical chamber 45 cm in diameter and 27 cm in length. The high-voltage electrode of the discharger was in the form of a cylinder 20 cm in diameter positioned coaxially inside the chamber. The 10-mm-diameter ground electrode was positioned radially in a branch pipe 8 cm long. The control electrode was placed in a 2-cm-diameter hole in the center of the ground electrode. The chamber with the test discharge was filled with transformer oil with a breakdown voltage of about 50 kV. The oil was not replaced or cleaned during the experiment. We did not find that contamination of the oil by discharge products had any effect on the time characteristics of either type of discharger. The results were analyzed by the least squares method, with 50 measurements to a point (it was found that time lag of the discharger triggering conforms approximately to a normal distribution law for both types of discharger).

Capturing Cyclic Variability in EGR Dilute SI Combustion using Multi-Cycle RANS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scarcelli, Riccardo; Sevik, James; Wallner, Thomas

Dilute combustion is an effective approach to increase the thermal efficiency of spark-ignition (SI) internal combustion engines (ICEs). However, high dilution levels typically result in large cycle-to-cycle variations (CCV) and poor combustion stability, therefore limiting the efficiency improvement. In order to extend the dilution tolerance of SI engines, advanced ignition systems are the subject of extensive research. When simulating the effect of the ignition characteristics on CCV, providing a numerical result matching the measured average in-cylinder pressure trace does not deliver useful information regarding combustion stability. Typically Large Eddy Simulations (LES) are performed to simulate cyclic engine variations, since Reynold-Averagedmore » Navier-Stokes (RANS) modeling is expected to deliver an ensemble-averaged result. In this paper it is shown that, when using RANS, the cyclic perturbations coming from different initial conditions at each cycle are not damped out even after many simulated cycles. As a result, multi-cycle RANS results feature cyclic variability. This allows evaluating the effect of advanced ignition sources on combustion stability but requires validation against the entire cycle-resolved experimental dataset. A single-cylinder GDI research engine is simulated using RANS and the numerical results for 20 consecutive engine cycles are evaluated for several operating conditions, including stoichiometric as well as EGR dilute operation. The effect of the ignition characteristics on CCV is also evaluated. Results show not only that multi-cycle RANS simulations can capture cyclic variability and deliver similar trends as the experimental data, but more importantly that RANS might be an effective, lower-cost alternative to LES for the evaluation of ignition strategies for combustion systems that operate close to the stability limit.« less

Factors associated with use of pre-operative chemoradiation therapy for rectal cancer in the Cancer Care Outcomes Research and Surveillance Consortium

PubMed Central

Charlton, Mary E.; Lin, Chi; Jiang, Dingfeng; Stitzenberg, Karyn B.; Halfdanarson, Thorvardur R.; Pendergast, Jane F.; Chrischilles, Elizabeth A.; Wallace, Robert B.

2012-01-01

Purpose Pre-operative (pre-op) chemoradiation therapy (CRT) improves local control and reduces toxicity more than post-operative (post-op) CRT for the treatment of stages II/III rectal cancer, but studies suggest many patients still receive post-op CRT. We examined patient beliefs, and clinical and provider characteristics associated with receipt of recommended therapy. Methods We identified stage II/III rectal cancer patients who had primary site resection and CRT among subjects in the Cancer Care Outcomes Research and Surveillance Consortium, a population- and health system-based prospective cohort of newly diagnosed colorectal cancer patients from 2003 to 2005. Patient surveys and abstracted medical records were used to construct variables and determine sequence of CRT and surgery. Logistic regression was used to model the association between predictors and receipt of pre-op CRT. Results Of the 201 patients, 66% received pre-op and 34% received post-op CRT. Those visiting a medical oncologist and/or radiation oncologist prior to a surgeon had a 96% (95% CI, 92% to 100%) predicted probability of receiving pre-op CRT, compared to 48% (95% CI, 41% to 55%) for those visiting a surgeon first. Among those visiting a surgeon first, documentation of recommended staging procedures was associated with receiving pre-op CRT. Conclusion Sequence of provider visits and documentation of recommended staging procedures were important predictors of receiving pre-op CRT. Initial multidisciplinary evaluation led to better adherence to CRT guidelines. Further evaluation of provider characteristics, referral patterns and related health system processes should be undertaken to inform targeted interventions to reduce variation from recommended care. PMID:22992624

The CURB65 pneumonia severity score outperforms generic sepsis and early warning scores in predicting mortality in community‐acquired pneumonia

PubMed Central

Barlow, Gavin; Nathwani, Dilip; Davey, Peter

2007-01-01

Background The performance of CURB65 in predicting mortality in community‐acquired pneumonia (CAP) has been tested in two large observational studies. However, it has not been tested against generic sepsis and early warning scores, which are increasingly being advocated for identification of high‐risk patients in acute medical wards. Method A retrospective analysis was performed of data prospectively collected for a CAP quality improvement study. The ability to stratify mortality and performance characteristics (sensitivity, specificity, positive predictive value, negative predictive value and area under the receiver operating curve) were calculated for stratifications of CURB65, CRB65, the systemic inflammatory response syndrome (SIRS) criteria and the standardised early warning score (SEWS). Results 419 patients were included in the main analysis with a median age of 74 years (men = 47%). CURB65 and CRB65 stratified mortality in a more clinically useful way and had more favourable operating characteristics than SIRS or SEWS; for example, mortality in low‐risk patients was 2% when defined by CURB65, but 9% when defined by SEWS and 11–17% when defined by variations of the SIRS criteria. The sensitivity, specificity, positive predictive value and negative predictive value of CURB65 was 71%, 69%, 35% and 91%, respectively, compared with 62%, 73%, 35% and 89% for the best performing version of SIRS and 52%, 67%, 27% and 86% for SEWS. CURB65 had the greatest area under the receiver operating curve (0.78 v 0.73 for CRB65, 0.68 for SIRS and 0.64 for SEWS). Conclusions CURB65 should not be supplanted by SIRS or SEWS for initial prognostic assessment in CAP. Further research to identify better generic prognostic tools is required. PMID:16928720

Impact of sex on 30-day complications and long-term functional outcomes following ileal pouch-anal anastomosis for chronic ulcerative colitis.

PubMed

McKenna, Nicholas P; Dozois, Eric J; Pemberton, John H; Lightner, Amy L

2018-05-01

To determine the impact of patient sex on operative characteristics, short-term complications, and long-term functional outcomes following ileal pouch-anal anastomosis (IPAA) for chronic ulcerative colitis (CUC). A retrospective review was performed on all patients undergoing two- or three-stage IPAA for CUC at our institution between January 2002 and August 2013. Patient demographics, operative characteristics, 30-day postoperative complications, and long-term functional outcomes from annual survey data were analyzed comparing men and women patients. During the study period, 911 IPAAs (542 men, 369 women) were performed. Men were older and were more often obese (both p < 0.01). Use of a three-stage approach and laparoscopic approach were similar between men and women, but operation length, intraoperative blood loss, and hospital length of stay were all higher in men (all p < 0.05). At 30 days, women had increased rates of superficial surgical site infections and urinary tract infections (both p < 0.05), while men had increased rates of urinary retention (p = 0.03). Five hundred forty-six patients (60%; 307 men, 239 women) responded to the annual post IPAA survey with a median follow-up of 5.1 and 5.0 years in men and women, respectively. Women reported increased frequency of daytime stools in the early follow-up period, but this difference resolved with time. Other functional outcomes were similar. Patient sex impacts intraoperative complexity, postoperative length of stay, 30-day postoperative outcomes, and initial long-term function. These findings underscore the need to adjust preoperative counseling regarding IPAA outcomes based on sex.

A Technique for the Assessment of Flight Operability Characteristics of Human Rated Spacecraft

NASA Technical Reports Server (NTRS)

Crocker, Alan

2010-01-01

In support of new human rated spacecraft development programs, the Mission Operations Directorate at NASA Johnson Space Center has implemented a formal method for the assessment of spacecraft operability. This "Spacecraft Flight Operability Assessment Scale" defines six key themes of flight operability, with guiding principles and goals stated for each factor. A standardized rating technique provides feedback that is useful to the operations, design and program management communities. Applicability of this concept across the program structure and life cycle is addressed. Examples of operationally desirable and undesirable spacecraft design characteristics are provided, as is a sample of the assessment scale product.

In-Flight Operation of the Dawn Ion Propulsion System - The First Nine Months

NASA Technical Reports Server (NTRS)

Garner, Charles E.; Brophy, John R.; Mikes, Steven C.; Raymond, Marc D.

2008-01-01

The Dawn mission, part of NASA's Discovery Program, has as its goal the scientific exploration of the two most massive main-belt asteroids, Vesta and Ceres. The Dawn spacecraft was launched from Cape Canaveral Air Force Station on September 27, 2007 on a Delta-II 7925H-9.5 (Delta-II Heavy) rocket that placed the 1218 kg spacecraft into an Earth-escape trajectory. On-board the spacecraft is an ion propulsion system (IPS) which will provide most of the delta-V needed for heliocentric transfer to Vesta, orbit capture at Vesta, transfer to Vesta science orbits, departure and escape from Vesta, heliocentric transfer to Ceres, orbit capture at Ceres, and transfer to Ceres science orbits. The Dawn ion engine design is based on the design validated on NASA's Deep Space 1 mission. However, because of the very substantial (11 km/s) delta-V requirements for this mission Dawn requires two engines to complete its mission objectives. The power processor units (PPU), digital control and interface units (DCIU) slice boards and the xenon control assembly (XCA) are also based on the DS1 design. The DCIUs and thrust gimbal assemblies (TGA) were developed at the Jet Propulsion Laboratory. The spacecraft was provided by Orbital Sciences Corporation, Sterling, Virginia, and the mission is managed by and operated from the Jet Propulsion Laboratory. Dawn partnered with Germany, Italy and Los Alamos National Laboratory for the science instruments. The mission is led by the principal investigator, Dr. Christopher Russell, from the University of California, Los Angeles. The first 80 days after launch were dedicated to the initial checkout of the spacecraft prior to the initiation of long-term thrusting for the heliocentric transfer to Vesta. The IPS hardware, consisting of three ion thrusters and TGAs, two PPUs and DCIUs, xenon feed system, and spacecraft control software, was investigated extensively. Thrust measurements, roll torque measurements, pointing capabilities, control characteristics, and thermal behavior of the spacecraft and IPS were carefully evaluated. The Dawn IPS fully met all its initial checkout performance objectives. Deterministic thrusting for cruise began on December 17, 2007. Over the subsequent approximately 330 days the IPS will be operated virtually continuously at full power thrusting (approximately 91 mN) leading to a Mars flyby in February 2009. The encounter with Mars provides a gravity assist for a plane change and is the only source of post-launch delta-V apart from the IPS. Following the Mars gravity assist IPS will be operated for approximately one year at full power and for 1.3 years at throttled power levels leading to rendezvous with Vesta in August of 2011. Following nine months of orbital operations with IPS providing the propulsion needed for orbit capture, science orbit transfer and orbit maintenance and Vesta escape, Dawn will transit to Ceres with an expected arrival date of February 2015. As of June 16, 2008 the ion thrusters on Dawn have operated for close to 3,846 hours and have delivered nearly 1 km/s of delta-V to the spacecraft. Dawn IPS operation has been almost flawless during the initial checkout and six months of cruise. This paper provides an overview of Dawn's mission objectives, mission and system design, and the results of the post-launch Dawn IPS mission operations through June 2008

7 CFR 43.105 - Operating characteristics (OC) curves.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 43.105 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY STANDARDS AND STANDARD CONTAINER REGULATIONS STANDARDS FOR SAMPLING PLANS Sampling Plans § 43.105 Operating characteristics (OC...

Fission Surface Power Systems (FSPS) Project Final Report for the Exploration Technology Development Program (ETDP): Fission Surface Power, Transition Face to Face

NASA Technical Reports Server (NTRS)

Palac, Donald T.

2011-01-01

The Fission Surface Power Systems Project became part of the ETDP on October 1, 2008. Its goal was to demonstrate fission power system technology readiness in an operationally relevant environment, while providing data on fission system characteristics pertinent to the use of a fission power system on planetary surfaces. During fiscal years 08 to 10, the FSPS project activities were dominated by hardware demonstrations of component technologies, to verify their readiness for inclusion in the fission surface power system. These Pathfinders demonstrated multi-kWe Stirling power conversion operating with heat delivered via liquid metal NaK, composite Ti/H2O heat pipe radiator panel operations at 400 K input water temperature, no-moving-part electromagnetic liquid metal pump operation with NaK at flight-like temperatures, and subscale performance of an electric resistance reactor simulator capable of reproducing characteristics of a nuclear reactor for the purpose of system-level testing, and a longer list of component technologies included in the attached report. Based on the successful conclusion of Pathfinder testing, work began in 2010 on design and development of the Technology Demonstration Unit (TDU), a full-scale 1/4 power system-level non-nuclear assembly of a reactor simulator, power conversion, heat rejection, instrumentation and controls, and power management and distribution. The TDU will be developed and fabricated during fiscal years 11 and 12, culminating in initial testing with water cooling replacing the heat rejection system in 2012, and complete testing of the full TDU by the end of 2014. Due to its importance for Mars exploration, potential applicability to missions preceding Mars missions, and readiness for an early system-level demonstration, the Enabling Technology Development and Demonstration program is currently planning to continue the project as the Fission Power Systems project, including emphasis on the TDU completion and testing.

The impact of airport characteristics on airport surface accidents and incidents.

PubMed

Wilke, Sabine; Majumdar, Arnab; Ochieng, Washington Y

2015-06-01

Airport surface safety and in particular runway and taxiway safety is acknowledged globally as one of aviation's greatest challenges. To improve this key area of aviation safety, it is necessary to identify and understand the causal and contributing factors on safety occurrences. While the contribution of human factors, operations, and procedures has been researched extensively, the impact of the airport and its associated characteristics itself has received little or no attention. This paper introduces a novel methodology for risk and hazard assessment of airport surface operations, and models the relationships between airport characteristics, and (a) the rate of occurrences, (b) the severity of occurrences, and (c) the causal factors underlying occurrences. The results show for the first time how the characteristics of airports, and in particular its infrastructure and operations, influence the safety of surface operations. Copyright © 2015 Elsevier Ltd. and National Safety Council. Published by Elsevier Ltd. All rights reserved.

Surgeon specialization and use of sentinel lymph node biopsy for breast cancer

PubMed Central

Yen, Tina W.F.; Laud, Purushuttom W.; Sparapani, Rodney A.; Nattinger, Ann B.

2014-01-01

IMPORTANCE Sentinel lymph node biopsy (SLNB) is the standard of care for axillary staging in clinically node-negative breast cancer patients. It is not known whether SLNB rates differ by surgeon expertise. If surgeons with less breast cancer expertise are less likely to offer SLNB to clinically node-negative patients, this practice pattern could lead to unnecessary axillary lymph node dissections (ALND) and lymphedema. OBJECTIVE To explore potential measures of surgical expertise (including a novel objective specialization measure – percentage of a surgeon’s operations devoted to breast cancer determined from claims) on the use of SLNB for invasive breast cancer. DESIGN Population-based prospective cohort study. Patient, tumor, treatment and surgeon characteristics were examined. SETTING California, Florida, Illinois PARTICIPANTS Elderly (65+ years) women identified from Medicare claims as having had incident invasive breast cancer surgery in 2003. MAIN OUTCOME MEASURES Type of axillary surgery performed. RESULTS Of the 1,703 women treated by 863 different surgeons, 56% underwent an initial SLNB, 37% initial ALND and 6% no axillary surgery. The median annual surgeon Medicare volume of breast cancer cases was 6 (range: 1.5–57); the median surgeon percentage of breast cancer cases was 4.6% (range: 0.7%–100%). After multivariable adjustment of patient and surgeon factors, women operated on by surgeons with higher volumes and percentages of breast cancer cases had a higher likelihood of undergoing SLNB. Specifically, women were most likely to undergo SLNB if operated on by high volume surgeons (regardless of percentage) or by lower volume surgeons with a high percentage of cases devoted to breast cancer. In addition, membership in the American Society of Breast Surgeons (OR 1.98, CI 1.51–2.60) and Society of Surgical Oncology (OR 1.59, CI 1.09–2.30) were independent predictors of women undergoing an initial SLNB. CONCLUSIONS AND RELEVANCE Patients treated by surgeons with more experience and focus in breast cancer were significantly more likely to undergo SLNB, highlighting the importance of receiving initial treatment by specialized providers. Factors relating to specialization in a particular area, including our novel surgeon percentage measure, require further investigation as potential indicators of quality of care. PMID:24369337

Concept of operations : Dallas Integrated Corridor Management (ICM) demonstration project.

DOT National Transportation Integrated Search

2010-06-01

This concept of operations (Con Ops) for the US-75 Integrated Corridor Management (ICM) Program has been developed as part of the US Department of Transportation Integrated Corridor Management Initiative, which is an innovative research initiative th...

SNAP 10A ESTIMATED ELECTRICAL CHARACTERISTICS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cooper, J.C.

1961-06-01

The electrical power characteristics of a SNAP 10A converter are estimated for given fractions of power degradation. Graphs are included showing the power characteristics for instantaneous transients from stabilized operation at the maximum efficiency point, and after system temperature stabilization at the operating point. Open-circuit emf's of the converter are estimated for instantaneous and temperature-stabilized cases. (D.L.C.)

NEXT Long-Duration Test Plume and Wear Characteristics after 16,550 h of Operation and 337 kg of Xenon Processed

NASA Technical Reports Server (NTRS)

Herman, Daniel A.; Soulas, George C.; Patterson, Michael J.

2009-01-01

The NASA s Evolutionary Xenon Thruster (NEXT) program is developing the next-generation ion propulsion system with significant enhancements beyond the state-of-the-art. The NEXT ion propulsion system provides improved mission capabilities for future NASA science missions to enhance and enable Discovery, New Frontiers, and Flagship-type NASA missions. As part of a comprehensive thruster service life assessment utilizing both testing and analyses, a Long-Duration Test (LDT) was initiated to validate and qualify the NEXT propellant throughput capability to a qualification-level of 450 kg, 1.5 times the mission-derived throughput requirement of 300 kg. This wear test is being conducted with a modified, flight-representative NEXT engineering model ion thruster, designated EM3. As of June 25, 2008, the thruster has accumulated 16,550 h of operation: the first 13,042 h at the thruster full-input-power of 6.9 kW with 3.52 A beam current and 1800 V beam power supply voltage. Operation since 13,042 h, i.e., the most recent 3,508 h, has been at an input power of 4.7 kW with 3.52 A beam current and 1180 V beam power supply voltage. The thruster has processed 337 kg of xenon (Xe) surpassing the NSTAR propellant throughput demonstrated during the extended life testing of the Deep Space 1 flight spare. The NEXT LDT has demonstrated a total impulse of 13.3 106 N s; the highest total impulse ever demonstrated by an ion thruster. Thruster plume diagnostics and erosion measurements are obtained periodically over the entire NEXT throttle table with input power ranging 0.5 to 6.9 kW. Observed thruster component erosion rates are consistent with predictions and the thruster service life assessment. There have not been any observed anomalous erosion and all erosion estimates indicate a thruster throughput capability that exceeds 750 kg of Xe, an equivalent of 36,500 h of continuous operation at the full-power operating condition. This paper presents the erosion measurements and plume diagnostic results for the NEXT LDT to date with emphasis on the change in thruster operating condition and resulting impact on wear characteristics. Ion optics grid-gap data, both cold and operating, are presented. Performance and wear predictions for the LDT throttle profile are presented.

Trends and determinants for early initiation of and exclusive breastfeeding under six months in Vietnam: results from the Multiple Indicator Cluster Surveys, 2000-2011.

PubMed

Bui, Quyen Thi-Tu; Lee, Hwa-Young; Le, Anh Thi-Kim; Van Dung, Do; Vu, Lan Thi-Hoang

2016-01-01

There is strong evidence that breastfeeding (BF) significantly benefits mothers and infants in various ways. Yet the proportion of breastfed babies in Vietnam is low and continues to decline. This study fills an important evidence gap in BF practices in Vietnam. This paper examines the trend of early initiation of BF and exclusive BF from 2000 to 2011 in Vietnam and explores the determinants at individual and contextual levels. Data from three waves of the Multiple Indicator Cluster Survey were combined to estimate crude and adjusted trends over time for two outcomes - early initiation of BF and exclusive BF. Three-level logistic regressions were fitted to examine the impacts of both individual and contextual characteristics on early initiation of BF and exclusive BF in the 2011 data. Both types of BF showed a decreasing trend over time after controlling for individual-level characteristics but this trend was more evident for early initiation of BF. Apart from child's age, individual-level characteristics were not significant predictors of the BF outcomes, but provincial characteristics had a strong association. When controlling for individual-level characteristics, mothers living in provinces with a higher percentage of mothers with more than three children were more likely to have initiated early BF (odds ratio [OR]: 1.06; confidence interval [CI]: 1.02-1.11) but less likely to exclusively breastfeed their babies (OR: 0.94; CI: 0.88-1.01). Mothers living in areas with a higher poverty rate were more likely to breastfeed exclusively (OR: 1.07; CI: 1.02-1.13), and those who delivered by Caesarean section were less likely to initiate early BF. Our results suggest that environmental factors are becoming more important for determining BF practices in Vietnam. Intervention programs should therefore not only consider individual factors, but should also consider the potential impact of contextual factors on BF practices.

Characteristic operator functions for quantum input-plant-output models and coherent control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gough, John E.

We introduce the characteristic operator as the generalization of the usual concept of a transfer function of linear input-plant-output systems to arbitrary quantum nonlinear Markovian input-output models. This is intended as a tool in the characterization of quantum feedback control systems that fits in with the general theory of networks. The definition exploits the linearity of noise differentials in both the plant Heisenberg equations of motion and the differential form of the input-output relations. Mathematically, the characteristic operator is a matrix of dimension equal to the number of outputs times the number of inputs (which must coincide), but with entriesmore » that are operators of the plant system. In this sense, the characteristic operator retains details of the effective plant dynamical structure and is an essentially quantum object. We illustrate the relevance to model reduction and simplification definition by showing that the convergence of the characteristic operator in adiabatic elimination limit models requires the same conditions and assumptions appearing in the work on limit quantum stochastic differential theorems of Bouten and Silberfarb [Commun. Math. Phys. 283, 491-505 (2008)]. This approach also shows in a natural way that the limit coefficients of the quantum stochastic differential equations in adiabatic elimination problems arise algebraically as Schur complements and amounts to a model reduction where the fast degrees of freedom are decoupled from the slow ones and eliminated.« less

The effect of operative fit and hydroxyapatite coating on the mechanical and biological response to porous implants.

PubMed

Dalton, J E; Cook, S D; Thomas, K A; Kay, J F

1995-01-01

Femoral intramedullary implants were constructed by threading 4.0-millimeter-thick disks with a titanium-alloy (Ti-6Al-4V) porous bead coating onto a two-millimeter-diameter threaded rod. Each porous-coated disk, which was 6.0, 8.0, 9.0, or 10.0 millimeters in diameter, was separated by a two-millimeter-thick acrylic disk with a diameter of ten millimeters. Implants with and without a hydroxyapatite coating of twenty-five micrometers were inserted into fifteen skeletally mature adult mongrel dogs. The femoral canal was sequentially reamed bilaterally to a ten-millimeter diameter, resulting in uniform initial implant-bone interface gaps of 0.0, 0.5, 1.0, and 2.0 millimeters. Each animal received paired hydroxyapatite-coated and uncoated implants. Three animals each were killed at four, eight, twelve, twenty-four, and fifty-two weeks after the implantation. The harvested femora were sectioned through the acrylic spacers, transverse to the long axis, to produce individual push-out test specimens for mechanical testing. Characteristics of interface attachment were determined with test fixtures that supported the surrounding bone to within 150 micrometers of the interface. Histological sections were prepared, and the amount of bone within the porous structure and the amount of the original gap that was filled with new bone were quantified with a computerized video image-analysis system. Mechanical attachment strength and bone ingrowth were found to increase with the time after implantation and with a decrease in the size of the gap. Placement of the implant in proximal (cancellous) compared with distal (cortical) locations had no significant effect on the strength of attachment, bone ingrowth, or gap-filling. However, implants with a large initial gap (1.0 or 2.0 millimeters) demonstrated greater attachment strength in cancellous bone than in cortical bone. With a few exceptions, hydroxyapatite-coated implants with an initial gap of 1.0 millimeter or less demonstrated significantly increased mechanical attachment strength and bone ingrowth at all time-periods. Interface attachment strengths were positively correlated with bone ingrowth, the time after implantation, the use of a hydroxyapatite coating, and decreasing initial gap size. Initial implant-bone apposition is thought to be a prerequisite for good biological fixation. This apposition is often not achieved because of the design of the implant or instruments and the operative technique. Poor initial fit during the operation may decrease the longevity of the implant. The results of the present study indicate that attachment strength and bone ingrowth are significantly affected by gaps in the interface, particularly those of more than 1.0 millimeter.(ABSTRACT TRUNCATED AT 400 WORDS)

Phenomenological characteristic of the electron component in gamma-quanta initiated showers

NASA Technical Reports Server (NTRS)

Nikolsky, S. I.; Stamenov, J. N.; Ushev, S. Z.

1985-01-01

The phenomenological characteristics of the electron component in showers initiated by primary gamma-quanta were analyzed on the basis of the Tien Shan experimental data. It is shown that the lateral distribution of the electrons ion gamma-quanta initiated showers can be described with NKG - function with age parameters bar S equals 0, 76 plus or minus 0, 02, different from the same parameter for normal showers with the same size bar S equals 0, 85 plus or minus 0, 01. The lateral distribution of the correspondent electron energy flux in gamma-quanta initiated showers is steeper as in normal cosmic ray showers.

Operational Suitability Guide. Volume 2. Templates

DTIC Science & Technology

1990-05-01

Intended mission, and the required technical and operational characteristics. The mission must be adequately defined and key hardware and software ...operational availability. With the use of fault-tolerant computer hardware and software , the system R&M will significantly improve end-to-end...should Include both hardware and software elements, as appropriate. Unique characteristics or unique support concepts should be Identified if they result

Unstable behaviour of RPT when testing turbine characteristics in the laboratory

NASA Astrophysics Data System (ADS)

Nielsen, T. K.; Fjørtoft Svarstad, M.

2014-03-01

A reversible pump turbine is a machine that can operate in three modes of operation i.e. in pumping mode. in turbine mode and in phase compensating mode (idle speed). Reversible pump turbines have an increasing importance for regulation purposes for obtaining power balance in electric power systems. Especially in grids dominated by thermal energy. reversible pump turbines improve the overall power regulating ability. Increased use of renewables (wind-. wave- and tidal power plants) will utterly demand better regulation ability of the traditional water power systems. enhancing the use of reversible pump turbines. A reversible pump turbine is known for having incredible steep speed - flow characteristics. As the speed increases the flow decreases more than that of a Francis turbines with the same specific speed. The steep characteristics might cause severe stability problems in turbine mode of operation. Stability in idle speed is a necessity for phasing in the generator to the electric grid. In the design process of a power plant. system dynamic simulations must be performed in order to check the system stability. The turbine characteristics will have to be modelled with certain accuracy even before one knows the exact turbine design and have measured characteristics. A representation of the RPT characteristics for system dynamic simulation purposes is suggested and compared with measured characteristics. The model shows good agreement with RPT characteristics measured in The Waterpower Laboratory. Because of the S-shaped characteristics. there is a stability issue involved when measuring these characteristics. Without special measures. it is impossible to achieve stable conditions in certain operational points. The paper discusses the mechanism when using a throttle to achieve system stability. even if the turbine characteristics imply instability.

Partnering for transportation safety : human-centered systems : operator fatigue management conference

DOT National Transportation Integrated Search

2000-01-01

This Conference was intended to enlist support for, and participation in, a new multi-modal DOT safety initiative. This initiative builds on the modal agency programs within DOT to develop techniques that transportation operating companies can employ...

40 CFR 63.4330 - By what date must I conduct the initial compliance demonstration?

Code of Federal Regulations, 2010 CFR

2010-07-01

... operations, the organic HAP emission rate for the initial compliance period was equal to or less than the applicable emission limit in Table 1 to this subpart and for dyeing/finishing operations, the mass fraction...

The Stratospheric Observatory for Infrared Astronomy (SOFIA)

NASA Astrophysics Data System (ADS)

Gehrz, Robert; Becklin, Eric; Young, Erick; Krabbe, Alfred; Marcum, Pamela; Roellig, Thomas

The Stratospheric Observatory for Infrared Astronomy (SOFIA) is a joint U.S./German Project to develop and operate a 2.5-meter infrared airborne telescope in a Boeing 747-SP that flies in the stratosphere at altitudes as high as 45,000 and is capable of observations from 0.3 microns to 1.6 mm with an average transmission greater than 80 percent. SOFIA will be staged out of the NASA Dryden Flight Research Center aircraft operations facility at Palmdale, CA and the SOFIA Science Mission Operations Center (SSMOC) will be located at NASA Ames Research Center, Moffett Field, CA. First science flights will begin in 2010, and the number of flights will ramp up annually with a flight rate of over 100 8 to 10 hour flights per year expected by 2014. The observatory is expected to operate until the mid 2030's. SOFIA will initially fly with eight focal plane instruments that include broadband imagers, moderate resolution spectrographs that will resolve broad features due to dust and large molecules, and high resolution spectrometers capable of studying the kinematics of molecular and atomic gas lines at km/s resolution. We describe the SOFIA facility and outline the opportunities for observations by the general scientific community and future instrumentation developments. The operational characteristics of the SOFIA first-generation instruments are summarized and we give several specific examples of the types of scientific studies to which these instruments are expected to make fundamental scientific contributions.

Early pregnancy failure management among family physicians.

PubMed

Wallace, Robin; Dehlendorf, Christine; Vittinghoff, Eric; Gold, Katherine J; Dalton, Vanessa K

2013-03-01

Family physicians, as primary care providers for reproductive-aged women, frequently initiate or refer patients for management of early pregnancy failure (EPF). Safe and effective options for EPF treatment include expectant management, medical management with misoprostol, and aspiration in the office or operating room. Current practice does not appear to reflect patient preferences or to utilize the most cost-effective treatments. We compared characteristics and practice patterns among family physicians who do and do not provide multiple options for EPF care. We performed a secondary analysis of a national survey of women's health providers to describe demographic and practice characteristics among family physicians who care for women with EPF. We used multivariate logistic regression to identify correlates of providing more than one option for EPF management. The majority of family physicians provide only one option for EPF; expectant management was most frequently used among our survey respondents. Misoprostol and office-based aspiration were rarely used. Providing more than one option for EPF management was associated with more years in practice, smaller county population, larger proportions of Medicaid patients, intrauterine contraception provision, and prior training in office-based aspiration. Family physicians are capable of providing a comprehensive range of options for EPF management in the outpatient setting but few providers currently do so. To create a more patient-centered and cost-effective model of care for EPF, additional resources should be directed at education, skills training, and system change initiatives to prepare family physicians to offer misoprostol and office-based aspiration to women with EPF.

Pre-operative nutrition support in patients undergoing gastrointestinal surgery.

PubMed

Burden, Sorrel; Todd, Chris; Hill, James; Lal, Simon

2012-11-14

Post-operative management in gastrointestinal (GI) surgery is becoming well established with 'Enhanced Recovery After Surgery' protocols starting 24 hours prior to surgery with carbohydrate loading and early oral or enteral feeding given to patients the first day following surgery. However, whether or not nutritional intervention should be initiated earlier in the preoperative period remains unclear. Poor pre-operative nutritional status has been linked consistently to an increase in post-operative complications and poorer surgical outcome. To review the literature on preoperative nutritional support in patients undergoing gastrointestinal surgery (GI). The searches were initially run in March 2011 and subsequently updated in February 2012. Databases including all EBM Reviews (Cochrane DSR, ACP Journal Club, DARE, CCTR, CMR, HTA and NHSEED) MEDLINE, EMBASE, AMED, British Nursing Index Archive using OvidSP were included and a search was run on each database separately after which duplicates were excluded. The inclusion criteria were randomised controlled trials that evaluated pre-operative nutritional support in GI surgical participants using a nutritional formula delivered by a parenteral, enteral or oral route. The primary outcomes included post-operative complications and length of hospital stay. Two observers screened the abstracts for inclusion in the review and performed data extraction. Bias was assessed for each of the included studies using the bias assessment tables in the Cochrane Software Review Manager (version 5.1, Cochrane Collaboration). The trials were analysed using risk ratios with Mantel-Haenszel in fixed effects methods displayed with heterogeneity. Meta-analyses were undertaken on trials evaluating immune enhancing (IE) nutrition, standard oral supplements, enteral and parenteral nutrition (PN) which were administered pre-operatively.Study characteristics were summarised in tables. Dichotomous and ratio data were entered into meta-analyses for the primary outcomes. These were then summarised in tables with assumed and corresponding risk with relative effect giving 95% confidence intervals. The searches identified 9900 titles and, after excluding duplicates, 6433 titles were initially screened. After the initial title screen, 6266 were excluded. Abstracts were screened for 167 studies and 33 articles were identified as meeting the inclusion criteria, of which 13 were included in the review after an assessment of the complete manuscripts.Seven trials evaluating IE nutrition were included in the review, of which 6 were combined in a meta-analysis. These studies showed a low to moderate level of heterogeneity and significantly reduced total post-operative complications (risk ratio (RR) 0.67 CI 0.53 to 0.84). Three trials evaluating PN were included in a meta-analysis and a significant reduction in post-operative complications was demonstrated (RR 0.64 95% CI 0.46 to 0.87) with low heterogeneity, in predominantly malnourished participants. Two trials evaluating enteral nutrition (RR 0.79, 95% CI 0.56 to 1.10) and 3 trials evaluating standard oral supplements (RR 1.01 95% CI 0.56 to 1.10) were included, neither of which showed any difference in the primary outcomes. There have been significant benefits demonstrated with pre-operative administration of IE nutrition in some high quality trials. However, bias was identified which may limit the generalizability of these results to all GI surgical candidates and the data needs to be placed in context with other recent innovations in surgical management (eg-ERAS). Some unwanted effects have also been reported with components of IE nutrition in critical care patients and it is unknown whether there would be detrimental effects by administering IE nutrition to patients who could require critical care support after their surgery. The studies evaluating PN demonstrated that the provision of PN to predominantly malnourished surgical candidates reduced post-operative complications; however, these data may not be applicable to current clinical practice, not least because they have involved a high degree of 'hyperalimentation'. Trials evaluating enteral or oral nutrition were inconclusive and further studies are required to select GI surgical patients for these nutritional interventions.

Accuracy of Point-of-care Ultrasonography for Diagnosing Acute Appendicitis: A Systematic Review and Meta-analysis.

PubMed

Matthew Fields, J; Davis, Joshua; Alsup, Carl; Bates, Amanda; Au, Arthur; Adhikari, Srikar; Farrell, Isaac

2017-09-01

The use of ultrasonography (US) to diagnose appendicitis is well established. More recently, point-of-care ultrasonography (POCUS) has also been studied for the diagnosis of appendicitis, which may also prove a valuable diagnostic tool. The purpose of this study was through systematic review and meta-analysis to identify the test characteristics of POCUS, specifically US performed by a nonradiologist physician, in accurately diagnosing acute appendicitis in patients of any age. We conducted a thorough and systematic literature search of English language articles published on point-of-care, physician-performed transabdominal US used for the diagnosis of acute appendicitis from 1980 to May, 2015 using OVID MEDLINE In-Process & Other Non-indexed Citations and Scopus. Studies were selected and subsequently independently abstracted by two trained reviewers. A random-effects pooled analysis was used to construct a hierarchical summary receiver operator characteristic curve, and a meta-regression was performed. Quality of studies was assessed using the QUADAS-2 tool. Our search yielded 5,792 unique studies and we included 21 of these in our final review. Prevalence of disease in this study was 29.8%, (range = 6.4%-75.4%). The sensitivity and specificity for POCUS in diagnosing appendicitis were 91% (95% confidence interval [CI] = 83%-96%) and 97% (95% CI = 91%-99%), respectively. The positive and negative predictive values were 91 and 94%, respectively. Studies performed by emergency physicians had slightly lower test characteristics (sensitivity = 80%, specificity = 92%). There was significant heterogeneity between studies (I 2 = 99%, 95% CI = 99%-100%) and the quality of the reported studies was moderate, mostly due to unclear reporting of blinding of physicians and timing of scanning and patient enrollment. Several of the studies were performed by a single operator, and the education and training of the operators were variably reported. Point-of-care US has relatively high sensitivity and specificity for diagnosing acute appendicitis, although the data presented are limited by the quality of the original studies and large CIs. In the hands of an experienced operator, POCUS is an appropriate initial imaging modality for diagnosing appendicitis. Based on our results, it is premature to utilize POCUS as a stand-alone test or to rule out appendicitis. © 2017 by the Society for Academic Emergency Medicine.

Wetland Characteristics and Denitrification

EPA Science Inventory

This presentation serves as an initial summary of our wetland field work's watershed characteristics hydrologic characteristics, water quality measurements, and denitrification assays. We present our measurement results in the context of wetland type (Estuarine, Freshwater Mars...

Centaur operations at the space station: Cost and transportation analysis

NASA Technical Reports Server (NTRS)

1988-01-01

A study was conducted to expand on the results of an initial study entitled Centaur Operations at the Space Station. The previous study developed technology demonstration missions (TDMs) that utilized the Centaur G-prime upper stage to advance OTV technologies required for accomodations and operations at the Space Station. An initial evaluation was performed of the cost to NASA for TDM implementation. Due to the potential for commercial communication satellite operation utilizing the TDM hardware, an evaluation of the Centaur's transportation potential was also performed.

Preliminary Airspace Operations Simulations Findings Report

NASA Technical Reports Server (NTRS)

2005-01-01

Provides preliminary findings of the initial series (normal operations and contingency management) of airspace operations simulations. The key elements of this report discuss feedback from controller subjects for UAS flight above FL430. Findings provide initial evaluation of routine UAS operations above dense ARTCC airspace (ZOB), and identify areas of further research, policy direction and procedural development. This document further serves as an addendum to the detailed AOS simulation plan (Deliverable SIM001), incorporating feedback from FAA air traffic personnel and Access 5 IPTs.

Microstructural Effects on Initiation Behavior in HMX

NASA Astrophysics Data System (ADS)

Molek, Christopher; Welle, Eric; Hardin, Barrett; Vitarelli, Jim; Wixom, Ryan; Samuels, Philip

Understanding the role microstructure plays on ignition and growth behavior has been the subject of a significant body of research within the detonation physics community. The pursuit of this understanding is important because safety and performance characteristics have been shown to strongly correlate to particle morphology. Historical studies have often correlated bulk powder characteristics to the performance or safety characteristics of pressed materials. We believe that a clearer and more relevant correlation is made between the pressed microstructure and the observed detonation behavior. This type of assessment is possible, as techniques now exist for the quantification of the pressed microstructures. Our talk will report on experimental efforts that correlate directly measured microstructural characteristics to initiation threshold behavior of HMX based materials. The internal microstructures were revealed using an argon ion cross-sectioning technique. This technique enabled the quantification of density and interface area of the pores within the pressed bed using methods of stereology. These bed characteristics are compared to the initiation threshold behavior of three HMX based materials using an electric gun based test method. Finally, a comparison of experimental threshold data to supporting theoretical efforts will be made.

Investigation of dynamic characteristics of a turbine-propeller engine

NASA Technical Reports Server (NTRS)

Oppenheimer, Frank L; Jacques, James R

1951-01-01

Time constants that characterize engine speed response of a turbine-propeller engine over the cruising speed range for various values of constant fuel flow and constant blade angle were obtained both from steady-state characteristics and from transient operation. Magnitude of speed response to changes in fuel flow and blade angle was investigated and is presented in the form of gain factors. Results indicate that at any given value of speed in the engine cruising speed range, time constants obtained both from steady-state characteristics and from transient operation agree satisfactorily for any given constant fuel flow, whereas time constants obtained from transient operation exceed time constants obtained from steady-state characteristics by approximately 14 percent for any given blade angle.

42 CFR 433.113 - Reduction of FFP for failure to operate a system and obtain initial approval.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Reduction of FFP for failure to operate a system... ADMINISTRATION Mechanized Claims Processing and Information Retrieval Systems § 433.113 Reduction of FFP for failure to operate a system and obtain initial approval. (a) Except as waived under § 433.130 or 433.131...

40 CFR Table 2 to Subpart Rrr of... - Summary of Operating Requirements for New and Existing Affected Sources and Emission Units

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Aluminum scrap shredder with fabric filter Bag leak detector or Initiate corrective action within 1-hr of... the performance test. Afterburner operation Operate in accordance with OM&M plan. b Bag leak detector... detector or Initiate corrective action within 1-hr of alarm and complete in accordance with the OM&M plan...

40 CFR Table 2 to Subpart Rrr of... - Summary of Operating Requirements for New and Existing Affected Sources and Emission Units

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Aluminum scrap shredder with fabric filter Bag leak detector or Initiate corrective action within 1-hr of... the performance test. Afterburner operation Operate in accordance with OM&M plan. b Bag leak detector... detector or Initiate corrective action within 1-hr of alarm and complete in accordance with the OM&M plan...

40 CFR Table 2 to Subpart Rrr of... - Summary of Operating Requirements for New and Existing Affected Sources and Emission Units

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Aluminum scrap shredder with fabric filter Bag leak detector or Initiate corrective action within 1-hr of... the performance test. Afterburner operation Operate in accordance with OM&M plan. b Bag leak detector... detector or Initiate corrective action within 1-hr of alarm and complete in accordance with the OM&M plan...