Hypervelocity Impact Initiation of Explosive Transfer Lines

NASA Technical Reports Server (NTRS)

Bjorkman, Michael D.; Christiansen, Eric L.

2012-01-01

The Gemini, Apollo and Space Shuttle spacecraft utilized explosive transfer lines (ETL) in a number of applications. In each case the ETL was located behind substantial structure and the risk of impact initiation by micrometeoroids and orbital debris was negligible. A current NASA program is considering an ETL to synchronize the actuation of pyrobolts to release 12 capture latches in a contingency. The space constraints require placing the ETL 50 mm below the 1 mm thick 2024-T72 Whipple shield. The proximity of the ETL to the thin shield prompted analysts at NASA to perform a scoping analysis with a finite-difference hydrocode to calculate impact parameters that would initiate the ETL. The results suggest testing is required and a 12 shot test program with surplused Shuttle ETL is scheduled for February 2012 at the NASA White Sands Test Facility. Explosive initiation models are essential to the analysis and one exists in the CTH library for HNS I, but not the HNS II used in the Shuttle 2.5 gr/ft rigid shielded mild detonating cord (SMDC). HNS II is less sensitive than HNS I so it is anticipated that these results using the HNS I model are conservative. Until the hypervelocity impact test results are available, the only check on the analysis was comparison with the Shuttle qualification test result that a 22 long bullet would not initiate the SMDC. This result was reproduced by the hydrocode simulation. Simulations of the direct impact of a 7 km/s aluminum ball, impacting at 0 degree angle of incidence, onto the SMDC resulted in a 1.5 mm diameter ball initiating the SMDC and 1.0 mm ball failing to initiate it. Where one 1.0 mm ball could not initiate the SMDC, a cluster of six 1.0 mm diameter aluminum balls striking simultaneously could. Thus the impact parameters that will result in initiating SMDC located behind a Whipple shield will depend on how well the shield fragments the projectile and spreads the fragments. An end-to-end simulation of the impact of an aluminum ball onto a Whipple shield covering SMDC is problematic due to the hydrocode fracture models. Regardless, two simulations were performed resulting in a 5 mm ball initiating the SMDC and a 4 mm ball failing to initiate the SMDC.

FIELD TEST OF CYCLODEXTRIN FOR ENHANCED IN-SITU FLUSHING OF MULTIPLE-COMPONENT IMMISCIBLE ORGANIC LIQUID CONTAMINATION: PROJECT OVERVIEW AND INITIAL RESULTS

EPA Science Inventory

The purpose of this paper is to present an overview and the initial results of a pilot-scale experiment designated to test the use of cyclodextrin for enhanced in-situ flushing of an aquifer contaminated by immiscible liquid. This is the first field test of this technology, terme...

Particle Size Effects on CL-20 Initiation and Detonation

NASA Astrophysics Data System (ADS)

Valancius, Cole; Bainbridge, Joe; Love, Cody; Richardson, Duane

2017-06-01

Particle size or specific surface area effects on explosives has been of interest to the explosives community for both application and modeling of initiation and detonation. Different particles sizes of CL-20 were used in detonator experiments to determine the effects of particle size on initiation, run-up to steady state detonation, and steady state detonation. Historical tests have demonstrated a direct relationship between particle size and initiation. However, historical tests inadvertently employed density gradients, making it difficult to discern the effects of particle size from the effects of density. Density gradients were removed from these tests using a larger diameter, shorter charge column, allowing for similar loading across different particle sizes. Without the density gradient, the effects of particle size on initiation and detonation are easier to determine. The results of which contrast with historical results, showing particle size does not directly affect initiation threshold.

40 CFR 94.508 - Calculation and reporting of test results.

Code of Federal Regulations, 2012 CFR

2012-07-01

... results. 94.508 Section 94.508 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Line Testing Programs § 94.508 Calculation and reporting of test results. (a) Manufacturers shall calculate initial test results using the applicable test procedure specified in § 94.506(a). These results...

40 CFR 94.508 - Calculation and reporting of test results.

Code of Federal Regulations, 2013 CFR

2013-07-01

... results. 94.508 Section 94.508 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Line Testing Programs § 94.508 Calculation and reporting of test results. (a) Manufacturers shall calculate initial test results using the applicable test procedure specified in § 94.506(a). These results...

Reducing Overutilization of Testing for Clostridium difficile Infection in a Pediatric Hospital System: A Quality Improvement Initiative.

PubMed

Klatte, J Michael; Selvarangan, Rangaraj; Jackson, Mary Anne; Myers, Angela L

2016-01-01

Study objectives included addressing overuse of Clostridium difficile laboratory testing by decreasing submission rates of nondiarrheal stool specimens and specimens from children ≤12 months of age and determining resultant patient and laboratory cost savings associated with decreased testing. A multifaceted initiative was developed, and components included multiple provider education methods, computerized order entry modifications, and automatic declination from laboratory on testing stool specimens of nondiarrheal consistency and from children ≤12 months old. A run chart, demonstrating numbers of nondiarrheal plus infant stool specimens submitted over time, was developed to analyze the initiative's impact on clinicians' test-ordering practices. A p-chart was generated to evaluate the percentage of these submitted specimens tested biweekly over a 12-month period. Cost savings for patients and the laboratory were assessed at the study period's conclusion. Run chart analysis revealed an initial shift after the interventions, suggesting a temporary decrease in testing submission; however, no sustained differences in numbers of specimens submitted biweekly were observed over time. On the p-chart, the mean percentage of specimens tested before the intervention was 100%. After the intervention, the average percentage of specimens tested dropped to 53.8%. Resultant laboratory cost savings totaled nearly $3600, and patient savings on testing charges were ∼$32 000. Automatic laboratory declination of nondiarrheal stools submitted for CDI testing resulted in a sustained decrease in the number of specimens tested, resulting in significant laboratory and patient cost savings. Despite multiple educational efforts, no sustained changes in physician ordering practices were observed. Copyright © 2016 by the American Academy of Pediatrics.

40 CFR 1033.320 - Calculation and reporting of test results.

Code of Federal Regulations, 2012 CFR

2012-07-01

... results. 1033.320 Section 1033.320 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Production Line Testing and Audit Programs § 1033.320 Calculation and reporting of test results. (a) Calculate initial test results using the applicable test procedure specified in § 1033.315(a). Include...

40 CFR 1033.320 - Calculation and reporting of test results.

Code of Federal Regulations, 2011 CFR

2011-07-01

... results. 1033.320 Section 1033.320 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Production Line Testing and Audit Programs § 1033.320 Calculation and reporting of test results. (a) Calculate initial test results using the applicable test procedure specified in § 1033.315(a). Include...

40 CFR 92.508 - Calculation and reporting of test results.

Code of Federal Regulations, 2012 CFR

2012-07-01

... results. 92.508 Section 92.508 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Remanufacturer Production Line Testing and Audit Programs § 92.508 Calculation and reporting of test results. (a) Manufacturers and remanufacturers shall calculate initial test results using the applicable test procedure...

40 CFR 92.508 - Calculation and reporting of test results.

Code of Federal Regulations, 2013 CFR

2013-07-01

... results. 92.508 Section 92.508 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Remanufacturer Production Line Testing and Audit Programs § 92.508 Calculation and reporting of test results. (a) Manufacturers and remanufacturers shall calculate initial test results using the applicable test procedure...

Pilot study of pharmacist-assisted delivery of pharmacogenetic testing in a primary care setting.

PubMed

Haga, Susanne B; LaPointe, Nancy M Allen; Cho, Alex; Reed, Shelby D; Mills, Rachel; Moaddeb, Jivan; Ginsburg, Geoffrey S

2014-09-01

To describe the rationale and design of a pilot program to implement and evaluate pharmacogenetic (PGx) testing in a primary care setting. Several factors have impeded the uptake of PGx testing, including lack of provider knowledge and challenges with operationalizing PGx testing in a clinical practice setting. We plan to compare two strategies for the implementation of PGx testing: a pharmacist-initiated testing arm compared with a physician-initiated PGx testing arm. Providers in both groups will be required to attend an introduction to PGx seminar. Anticipated results: We anticipate that providers in the pharmacist-initiated group will be more likely to order PGx testing than providers in the physician-initiated group. Overall, we aim to generate data that will inform an effective delivery model for PGx testing and to facilitate a seamless integration of PGx testing in primary care practices.

40 CFR 90.709 - Calculation and reporting of test results.

Code of Federal Regulations, 2012 CFR

2012-07-01

... results. 90.709 Section 90.709 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Manufacturer Production Line Testing Program § 90.709 Calculation and reporting of test results. (a) Initial test results are calculated following the applicable test procedure specified in § 90.707 (a). The...

40 CFR 90.709 - Calculation and reporting of test results.

Code of Federal Regulations, 2010 CFR

2010-07-01

... results. 90.709 Section 90.709 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Manufacturer Production Line Testing Program § 90.709 Calculation and reporting of test results. (a) Initial test results are calculated following the applicable test procedure specified in § 90.707 (a). The...

40 CFR 90.709 - Calculation and reporting of test results.

Code of Federal Regulations, 2013 CFR

2013-07-01

... results. 90.709 Section 90.709 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Manufacturer Production Line Testing Program § 90.709 Calculation and reporting of test results. (a) Initial test results are calculated following the applicable test procedure specified in § 90.707 (a). The...

40 CFR 90.709 - Calculation and reporting of test results.

Code of Federal Regulations, 2014 CFR

2014-07-01

... expressed to one additional significant figure. (b) Final test results are calculated by summing the initial... applicable standard expressed to one additional significant figure. (c) The final deteriorated test results...

40 CFR 90.709 - Calculation and reporting of test results.

Code of Federal Regulations, 2011 CFR

2011-07-01

... expressed to one additional significant figure. (b) Final test results are calculated by summing the initial... applicable standard expressed to one additional significant figure. (c) The final deteriorated test results...

Initiation of Insensitive High Explosives Using Multiple Wave Interactions

NASA Astrophysics Data System (ADS)

Francois, Elizabeth; Burritt, Rosmary; Biss, Matt; Bowden, Patrick

2017-06-01

Insensitive High Explosives (IHEs) increase safety in many types of weapons. However, the safety comes at the cost of performance. Initiation of IHE requires large boosters and powerful detonators as well. Multipoint initiation is being utilized to exploit explosive wave interactions to create overdriven states, greatly facilitating the initiation of IHEs. This presentation will build from recent explosive experiments where the minimum spot size for single-point initiation in PBX 9502 was determined. Below this threshold, PBX 9502 could not be initiated. This was then expanded to three initiation points, which were smaller this threshold. Measurements of the velocity and pressure of the wave interactions were measured using Photon Doppler Velocimetry (PDV). Initiation was observed, and the resulting pressures at the double and triple points were found to be above the CJ state for PBX 9502. Based on these results, further tests were conducted to isolate and measure the longevity and pressure of this phenomenon using cut-back tests. All results will be presented and discussed.

Effects of Polarization on Mechanical Properties of Lead Zirconate Titanate Ceramics Evaluated by Modified Small Punch Tests

NASA Astrophysics Data System (ADS)

Deng, Qihuang; Fan, Yuchi; Wang, Lianjun; Xiong, Zhi; Wang, Hongzhi; Li, Yaogang; Zhang, Qinghong; Kawasaki, Akira; Jiang, Wan

2012-01-01

Pb(Zr,Ti)O3 (PZT) ceramics were prepared by the conventional mixed oxide method, and the strength of the resultant PZT ceramics was evaluated using modified small punch (MSP) tests. Load-displacement curve test results showed that the crack-initiation and fracture strengths of PZT ceramics decreased after polarization. The effect of the polarization accelerated the fatigue properties of PZT ceramics. Scanning electron microscopy (SEM) results showed that microcracks were formed before the maximum load in the MSP test, and the first load drop corresponded to crack initiation.

Barriers to and acceptability of provider-initiated HIV testing and counselling and adopting HIV-prevention behaviours in rural Uganda: a qualitative study.

PubMed

Kiene, Susan M; Sileo, Katelyn; Wanyenze, Rhoda K; Lule, Haruna; Bateganya, Moses H; Jasperse, Joseph; Nantaba, Harriet; Jayaratne, Kia

2015-02-01

In Uganda, a nationwide scale-up of provider-initiated HIV testing and counselling presents an opportunity to deliver HIV-prevention services to large numbers of people. In a rural Ugandan hospital, focus group discussions and key informant interviews were conducted with outpatients receiving provider-initiated HIV testing and counselling and staff to explore the HIV-prevention information, motivation and behavioural skills strengths and weaknesses, and community-level and structural barriers to provider-initiated HIV testing and counselling acceptability and HIV prevention among this population. Strengths and weakness occurred at all levels, and results suggest brief client-centred interventions during provider-initiated HIV testing and counselling may be an effective approach to increase prevention behaviours in outpatient settings. © The Author(s) 2013.

Learning From Tests: Facilitation of Delayed Recall by Initial Recognition Alternatives.

ERIC Educational Resources Information Center

Whitten, William B., II; Leonard, Janet Mauriello

1980-01-01

Two experiments were designed to determine the effects of multiple-choice recognition test alternatives on subsequent memory for the correct answers. Results of both experiments are interpreted as demonstrations of the principle that long-term retention is facilitated such that memory evaluation occurs during initial recognition tests. (Author/RD)

Graded Aerobic Treadmill Testing in Adolescent Traumatic Brain Injury Patients.

PubMed

Cordingley, Dean M; Girardin, Richard; Morissette, Marc P; Reimer, Karen; Leiter, Jeff; Russell, Kelly; Ellis, Michael J

2017-11-01

To examine the safety and tolerability of clinical graded aerobic treadmill testing in recovering adolescent moderate and severe traumatic brain injury (TBI) patients referred to a multidisciplinary pediatric concussion program. We completed a retrospective case series of two moderate and five severe TBI patients (mean age, 17.3 years) who underwent initial Buffalo Concussion Treadmill Testing at a mean time of 71.6 days (range, 55-87) postinjury. Six patients completed one graded aerobic treadmill test each and one patient underwent initial and repeat testing. There were no complications. Five initial treadmill tests were completely tolerated and allowed an accurate assessment of exercise tolerance. Two initial tests were terminated early by the treatment team because of neurological and cardiorespiratory limitations. As a result of testing, two patients were cleared for aerobic exercise as tolerated and four patients were treated with individually tailored submaximal aerobic exercise programs resulting in subjective improvement in residual symptoms and/or exercise tolerance. Repeat treadmill testing in one patient performed after 1 month of treatment with submaximal aerobic exercise prescription was suggestive of improved exercise tolerance. One patient was able to tolerate aerobic exercise following surgery for posterior glottic stenosis. Preliminary results suggest that graded aerobic treadmill testing is a safe, well tolerated, and clinically useful tool to assess exercise tolerance in appropriately selected adolescent patients with TBI. Future prospective studies are needed to evaluate the effect of tailored submaximal aerobic exercise prescription on exercise tolerance and patient outcomes in recovering adolescent moderate and severe TBI patients.

40 CFR 91.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2010 CFR

2010-07-01

... results. 91.509 Section 91.509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Testing Program § 91.509 Calculation and reporting of test results. (a) Initial test results are... rounds these results, in accordance with ASTM E29-93a, to the number of decimal places contained in the...

40 CFR 91.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2013 CFR

2013-07-01

... results. 91.509 Section 91.509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Testing Program § 91.509 Calculation and reporting of test results. (a) Initial test results are... rounds these results, in accordance with ASTM E29-93a, to the number of decimal places contained in the...

40 CFR 91.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2012 CFR

2012-07-01

... results. 91.509 Section 91.509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Testing Program § 91.509 Calculation and reporting of test results. (a) Initial test results are... rounds these results, in accordance with ASTM E29-93a, to the number of decimal places contained in the...

Utility of repeat testing of critical values: a Q-probes analysis of 86 clinical laboratories.

PubMed

Lehman, Christopher M; Howanitz, Peter J; Souers, Rhona; Karcher, Donald S

2014-06-01

A common laboratory practice is to repeat critical values before reporting the test results to the clinical care provider. This may be an unnecessary step that delays the reporting of critical test results without adding value to the accuracy of the test result. To determine the proportions of repeated chemistry and hematology critical values that differ significantly from the original value as defined by the participating laboratory, to determine the threshold differences defined by the laboratory as clinically significant, and to determine the additional time required to analyze the repeat test. Participants prospectively reviewed critical test results for 4 laboratory tests: glucose, potassium, white blood cell count, and platelet count. Participants reported the following information: initial and repeated test result; time initial and repeat results were first known to laboratory staff; critical result notification time; if the repeat result was still a critical result; if the repeat result was significantly different from the initial result, as judged by the laboratory professional or policy; significant difference threshold, as defined by the laboratory; the make and model of the instrument used for primary and repeat testing. Routine, repeat analysis of critical values is a common practice. Most laboratories did not formally define a significant difference between repeat results. Repeated results were rarely considered significantly different. Median repeated times were at least 17 to 21 minutes for 10% of laboratories. Twenty percent of laboratories reported at least 1 incident in the last calendar year of delayed result reporting that clinicians indicated had adversely affected patient care. Routine repeat analysis of automated chemistry and hematology critical values is unlikely to be clinically useful and may adversely affect patient care.

Test results and facility description for a 40-kilowatt stirling engine

NASA Technical Reports Server (NTRS)

Kelm, G. G.; Cairelli, J. E.; Walter, R. J.

1981-01-01

A 40 kilowatt Stirling engine, its test support facilities, and the experimental procedures used for these tests are described. Operating experience with the engine is discussed, and some initial test results are presented

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Geoffrey Wayne; Leonard, Philip; Hartline, Ernest Leon

High Explosives Science and Technology (M-7) completed all required formulation and testing of Remediated Nitrate Salt (RNS) surrogates on April 27, 2016 as specified in PLAN-TA9-2443 Rev B, "Remediated Nitrate Salt (RNS) Surrogate Formulation and Testing Standard Procedure", released February 16, 2016. This report summarizes the results of the work and also includes additional documentation required in that test plan. All formulation and testing was carried out according to PLAN-TA9-2443 Rev B. The work was carried out in three rounds, with the full matrix of samples formulated and tested in each round. Results from the first round of formulation andmore » testing were documented in memorandum M7-J6-6042, " Results from First Round of Remediated Nitrate Salt Surrogate Formulation and Testing." Results from the second round of formulation and testing were documented in M7-16-6053 , "Results from the Second Round of Remediated Nitrate Salt Surrogate Formulation and Testing." Initial results from the third round were documented in M7-16-6057, "Initial Results from the Third Round of Remediated Nitrate Salt Formulation and Testing."« less

Initial test results with single cylinder rhombic drive Stirling engine

NASA Technical Reports Server (NTRS)

Cairelli, J. E.

1978-01-01

A brief description is given of the GPU 3-2 hardware, the test methods used, and the result of these tests. Comparison is made to unpublished data from similar hydrogen tests performed by the U.S. Army.

An augmented SMS intervention to improve access to antenatal CD4 testing and ART initiation in HIV-infected pregnant women: a cluster randomized trial.

PubMed

Dryden-Peterson, Scott; Bennett, Kara; Hughes, Michael D; Veres, Adrian; John, Oaitse; Pradhananga, Rosina; Boyer, Matthew; Brown, Carolyn; Sakyi, Bright; van Widenfelt, Erik; Keapoletswe, Koona; Mine, Madisa; Moyo, Sikhulile; Asmelash, Aida; Siedner, Mark; Mmalane, Mompati; Shapiro, Roger L; Lockman, Shahin

2015-01-01

Less than one-third of HIV-infected pregnant women eligible for combination antiretroviral therapy (ART) globally initiate treatment prior to delivery, with lack of access to timely CD4 results being a principal barrier. We evaluated the effectiveness of an SMS-based intervention to improve access to timely antenatal ART. We conducted a stepped-wedge cluster randomized trial of a low-cost programmatic intervention in 20 antenatal clinics in Gaborone, Botswana. From July 2011-April 2012, 2 clinics were randomly selected every 4 weeks to receive an ongoing clinic-based educational intervention to improve CD4 collection and to receive CD4 results via an automated SMS platform with active patient tracing. CD4 testing before 26 weeks gestation and ART initiation before 30 weeks gestation were assessed. Three-hundred-sixty-six ART-naïve women were included, 189 registering for antenatal care under Intervention and 177 under Usual Care periods. Of CD4-eligible women, 100 (59.2%) women under Intervention and 79 (50.6%) women under Usual Care completed CD4 phlebotomy before 26 weeks gestation, adjusted odds ratio (aOR, adjusted for time that a clinic initiated Intervention) 0.87 (95% confidence interval [CI]0.47-1.63, P = 0.67). The SMS-based platform reduced time to clinic receipt of CD4 test result from median of 16 to 6 days (P<0.001), was appreciated by clinic staff, and was associated with reduced operational cost. However, rates of ART initiation remained low, with 56 (36.4%) women registering under Intervention versus 37 (24.2%) women under Usual Care initiating ART prior to 30 weeks gestation, aOR 1.06 (95%CI 0.53-2.13, P = 0.87). The augmented SMS-based intervention delivered CD4 results more rapidly and efficiently, and this type of SMS-based results delivery platform may be useful for a variety of tests and settings. However, the intervention did not appear to improve access to timely antenatal CD4 testing or ART initiation, as obstacles other than CD4 impeded ART initiation during pregnancy.

40 CFR 90.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Calculation and reporting of test... Selective Enforcement Auditing § 90.509 Calculation and reporting of test results. (a) Initial test results... the number of tests conducted on the engine, and rounding to the same number of decimal places...

Characterization of the Edge Crack Torsion (ECT) Test for Mode III Fracture Toughness Measurement of Laminated Composites

NASA Technical Reports Server (NTRS)

Ratcliffe, James G.

2004-01-01

The edge crack torsion (ECT) test is designed to initiate mode III delamination growth in composite laminates. An ECT specimen is a rectangular laminate, containing an edge delamination at the laminate mid-plane. Torsion load is applied to the specimens, resulting in relative transverse shear sliding of the delaminated faces. The test data reduction schemes are intended to yield initiation values of critical mode III strain energy release rate, G(sub IIIc), that are constant with delamination length. The test has undergone several design changes during its development. The objective of this paper was to determine the suitability of the current ECT test design as a mode III fracture test. To this end, ECT tests were conducted on specimens manufactured from IM7/8552 and specimens made from S2/8552 tape laminates. Several specimens, each with different delamination lengths are tested. Detailed, three-dimensional finite element analyses of the specimens were performed. The analysis results were used to calculate the distribution of mode I, mode II, and mode III strain energy release rate along the delamination front. The results indicated that mode III-dominated delamination growth would be initiated from the specimen center. However, in specimens of both material types, the measured values of G(sub IIIc) exhibited significant dependence on delamination length. Furthermore, there was a large amount of scatter in the data. Load-displacement response of the specimens exhibited significant deviation from linearity before specimen failure. X-radiographs of a sample of specimens revealed that damage was initiated in the specimens prior to failure. Further inspection of the failure surfaces is required to identify the damage and determine that mode III delamination is initiated in the specimens.

Retrieval enhances eyewitness suggestibility to misinformation in free and cued recall.

PubMed

Wilford, Miko M; Chan, Jason C K; Tuhn, Sam J

2014-03-01

Immediately recalling a witnessed event can increase people's susceptibility to later postevent misinformation. But this retrieval-enhanced suggestibility (RES) effect has been shown only when the initial recall test included specific questions that reappeared on the final test. Moreover, it is unclear whether this phenomenon is affected by the centrality of event details. These limitations make it difficult to generalize RES to criminal investigations, which often begin with free recall prior to more specific queries from legal officials and attorneys. In 3 experiments, we examined the influence of test formats (free recall vs. cued recall) and centrality of event details (central vs. peripheral) on RES. In Experiment 1, both the initial and final tests were cued recall. In Experiment 2, the initial test was free recall and the final test was cued recall. In Experiment 3, both the initial and final tests were free recall. Initial testing increased misinformation reporting on the final test for peripheral details in all experiments, but the effect was significant for central details only after aggregating the data from all 3 experiments. These results show that initial free recall can produce RES, and more broadly, that free recall can potentiate subsequent learning of complex prose materials. © 2013 American Psychological Association

40 CFR 89.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Calculation and reporting of test... PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES Selective Enforcement Auditing § 89.509 Calculation and reporting of test results. (a) Initial test results...

40 CFR 90.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2013 CFR

2013-07-01

... results. 90.509 Section 90.509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Selective Enforcement Auditing § 90.509 Calculation and reporting of test results. (a) Initial test results... manufacturer shall round these results, in accordance with ASTM E29-93a, to the number of decimal places...

40 CFR 90.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2010 CFR

2010-07-01

... results. 90.509 Section 90.509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Selective Enforcement Auditing § 90.509 Calculation and reporting of test results. (a) Initial test results... manufacturer shall round these results, in accordance with ASTM E29-93a, to the number of decimal places...

40 CFR 90.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2012 CFR

2012-07-01

... results. 90.509 Section 90.509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Selective Enforcement Auditing § 90.509 Calculation and reporting of test results. (a) Initial test results... manufacturer shall round these results, in accordance with ASTM E29-93a, to the number of decimal places...

Preliminary Results of Solid Gas Generator Micropropulsion

NASA Technical Reports Server (NTRS)

deGroot, Wilhelmus A.; Reed, Brian D.; Brenizer, Marshall

1999-01-01

A decomposing solid thruster concept, which creates a more benign thermal and chemical environment than solid propellant combustion, while maintaining, performance similar to solid combustion, is described. A Micro-Electro-Mechanical (MEMS) thruster concept with diode laser and fiber-optic initiation is proposed, and thruster components fabricated with MEMS technology are presented. A high nitrogen content solid gas generator compound is evaluated and tested in a conventional axisymmetric thrust chamber with nozzle throat area ratio of 100. Results show incomplete decomposition of this compound in both low pressure (1 kPa) and high pressure (1 MPa) environments, with decomposition of up to 80% of the original mass. Chamber pressures of 1.1 MPa were obtained, with maximum calculated thrust of approximately 2.7 N. Resistively heated wires and resistively heated walls were used to initiate decomposition. Initiation tests using available lasers were unsuccessful, but infrared spectra of the compound show that the laser initiation tests used inappropriate wavelengths for optimal propellant absorption. Optimal wavelengths for laser ignition were identified. Data presented are from tests currently in progress. Alternative solid gas generator compounds are being evaluated for future tests.

Characterization of the Edge Crack Torsion (ECT) Test for Mode III Fracture Toughness Measurement of Laminated Composites

NASA Technical Reports Server (NTRS)

Ratcliffe, James G.

2004-01-01

The edge crack torsion (ECT) test is designed to initiate mode III delamination growth in composite laminates. The test has undergone several design changes during its development. The objective of this paper was to determine the suitability of the current ECT test design a mode III fracture test. To this end, ECT tests were conducted on specimens manufactured from IM7/8552 and S2/8552 tape laminates. Three-dimensional finite element analyses were performed. The analysis results were used to calculate the distribution of mode I, mode II, and mode III strain energy release rate along the delamination front. The results indicated that mode IIIdominated delamination growth would be initiated from the specimen center. However, in specimens of both material types, the measured values of GIIIc exhibited significant dependence on delamination length. Load-displacement response of the specimens exhibited significant deviation from linearity before specimen failure. X-radiographs of a sample of specimens revealed that damage was initiated in the specimens prior to failure. Further inspection of the failure surfaces is required to identify the damage and determine that mode III delamination is initiated in the specimens.

Assessing Very Early Infant Diagnosis Turnaround Times: Findings from a Birth Testing Pilot in Lesotho

PubMed Central

Hoffman, Heather J.; Mokone, Majoalane; Tukei, Vincent J.; Nchephe, Matsepeli; Phalatse, Mamakhetha; Tiam, Appolinaire; Guay, Laura; Mofenson, Lynne

2017-01-01

Very early infant diagnosis (VEID) (testing within two weeks of life), combined with rapid treatment initiation, could reduce early infant mortality. Our study evaluated turnaround time (TAT) to receipt of infants' HIV test results and ART initiation if HIV-infected, with and without birth testing availability. Data from facility records and national databases were collected for 12 facilities offering VEID, as part of an observational prospective cohort study, and 10 noncohort facilities. HIV-exposed infants born in January–June 2016 and any cohort infant diagnosed as HIV-infected at birth or six weeks were included. The median TAT from blood draw to caregiver result receipt was 76.5 days at birth and 63 and 70 days at six weeks at cohort and noncohort facilities, respectively. HIV-exposed infants tested at birth were approximately one month younger when their caregivers received results versus those tested at six weeks. Infants diagnosed at birth initiated ART about two months earlier (median 6.4 weeks old) than those identified at six weeks (median 14.8 weeks). However, the long TAT for testing at both birth and six weeks illustrates the prolonged process for specimen transport and result return that could compromise the effectiveness of adding VEID to existing overburdened EID systems. PMID:29410914

An Augmented SMS Intervention to Improve Access to Antenatal CD4 Testing and ART Initiation in HIV-Infected Pregnant Women: A Cluster Randomized Trial

PubMed Central

Dryden-Peterson, Scott; Bennett, Kara; Hughes, Michael D.; Veres, Adrian; John, Oaitse; Pradhananga, Rosina; Boyer, Matthew; Brown, Carolyn; Sakyi, Bright; van Widenfelt, Erik; Keapoletswe, Koona; Mine, Madisa; Moyo, Sikhulile; Asmelash, Aida; Siedner, Mark; Mmalane, Mompati; Shapiro, Roger L.; Lockman, Shahin

2015-01-01

Background Less than one-third of HIV-infected pregnant women eligible for combination antiretroviral therapy (ART) globally initiate treatment prior to delivery, with lack of access to timely CD4 results being a principal barrier. We evaluated the effectiveness of an SMS-based intervention to improve access to timely antenatal ART. Methods We conducted a stepped-wedge cluster randomized trial of a low-cost programmatic intervention in 20 antenatal clinics in Gaborone, Botswana. From July 2011-April 2012, 2 clinics were randomly selected every 4 weeks to receive an ongoing clinic-based educational intervention to improve CD4 collection and to receive CD4 results via an automated SMS platform with active patient tracing. CD4 testing before 26 weeks gestation and ART initiation before 30 weeks gestation were assessed. Results Three-hundred-sixty-six ART-naïve women were included, 189 registering for antenatal care under Intervention and 177 under Usual Care periods. Of CD4-eligible women, 100 (59.2%) women under Intervention and 79 (50.6%) women under Usual Care completed CD4 phlebotomy before 26 weeks gestation, adjusted odds ratio (aOR, adjusted for time that a clinic initiated Intervention) 0.87 (95% confidence interval [CI]0.47–1.63, P = 0.67). The SMS-based platform reduced time to clinic receipt of CD4 test result from median of 16 to 6 days (P<0.001), was appreciated by clinic staff, and was associated with reduced operational cost. However, rates of ART initiation remained low, with 56 (36.4%) women registering under Intervention versus 37 (24.2%) women under Usual Care initiating ART prior to 30 weeks gestation, aOR 1.06 (95%CI 0.53–2.13, P = 0.87). Conclusions The augmented SMS-based intervention delivered CD4 results more rapidly and efficiently, and this type of SMS-based results delivery platform may be useful for a variety of tests and settings. However, the intervention did not appear to improve access to timely antenatal CD4 testing or ART initiation, as obstacles other than CD4 impeded ART initiation during pregnancy. PMID:25693050

Mapping of medical acronyms and initialisms to Medical Subject Headings (MeSH) across selected systems

PubMed Central

Shultz, Mary

2006-01-01

Introduction: Given the common use of acronyms and initialisms in the health sciences, searchers may be entering these abbreviated terms rather than full phrases when searching online systems. The purpose of this study is to evaluate how various MEDLINE Medical Subject Headings (MeSH) interfaces map acronyms and initialisms to the MeSH vocabulary. Methods: The interfaces used in this study were: the PubMed MeSH database, the PubMed Automatic Term Mapping feature, the NLM Gateway Term Finder, and Ovid MEDLINE. Acronyms and initialisms were randomly selected from 2 print sources. The test data set included 415 randomly selected acronyms and initialisms whose related meanings were found to be MeSH terms. Each acronym and initialism was entered into each MEDLINE MeSH interface to determine if it mapped to the corresponding MeSH term. Separately, 46 commonly used acronyms and initialisms were tested. Results: While performance differed widely, the success rates were low across all interfaces for the randomly selected terms. The common acronyms and initialisms tested at higher success rates across the interfaces, but the differences between the interfaces remained. Conclusion: Online interfaces do not always map medical acronyms and initialisms to their corresponding MeSH phrases. This may lead to inaccurate results and missed information if acronyms and initialisms are used in search strategies. PMID:17082832

Electrochemical Testing of Ni-Cr-Mo-Gd Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

T. E. Lister; R. E. Mizia; H. Tian

2005-10-01

The waste package site recommendation design specified a boron-containing stainless steel, Neutronit 976/978, for fabrication of the internal baskets that will be used as a corrosion-resistant neutron-absorbing material. Recent corrosion test results gave higher-than-expected corrosion rates for this material. The material callout for these components has been changed to a Ni-Cr-Mo-Gd alloy (ASTM-B 932-04, UNS N06464) that is being developed at the Idaho National Laboratory. This report discusses the results of initial corrosion testing of this material in simulated in-package environments that could contact the fuel baskets after breach of the waste package outer barrier. The corrosion test matrix wasmore » executed using the potentiodynamic and potentiostatic electrochemical test techniques. The alloy performance shows low rates of general corrosion after initial removal of a gadolinium-rich second phase that intersects the surface. The high halide-containing test solutions exhibited greater tendencies toward initiation of crevice corrosion.« less

Compression of thick laminated composite beams with initial impact-like damage

NASA Technical Reports Server (NTRS)

Breivik, N. L.; Guerdal, Z.; Griffin, O. H., Jr.

1992-01-01

While the study of compression after impact of laminated composites has been under consideration for many years, the complexity of the damage initiated by low velocity impact has not lent itself to simple predictive models for compression strength. The damage modes due to non-penetrating, low velocity impact by large diameter objects can be simulated using quasi-static three-point bending. The resulting damage modes are less coupled and more easily characterized than actual impact damage modes. This study includes the compression testing of specimens with well documented initial damage states obtained from three-point bend testing. Compression strengths and failure modes were obtained for quasi-isotropic stacking sequences from 0.24 to 1.1 inches thick with both grouped and interspersed ply stacking. Initial damage prior to compression testing was divided into four classifications based on the type, extent, and location of the damage. These classifications are multiple through-thickness delaminations, isolated delamination, damage near the surface, and matrix cracks. Specimens from each classification were compared to specimens tested without initial damage in order to determine the effects of the initial damage on the final compression strength and failure modes. A finite element analysis was used to aid in the understanding and explanation of the experimental results.

Flexural testing on carbon fibre laminates taking into account their different behaviour under tension and compression

NASA Astrophysics Data System (ADS)

Serna Moreno, M. C.; Romero Gutierrez, A.; Martínez Vicente, J. L.

2016-07-01

An analytical model has been derived for describing the results of three-point-bending tests in materials with different behaviour under tension and compression. The shift of the neutral plane and the damage initiation mode and its location have been defined. The validity of the equations has been reviewed by testing carbon fibre-reinforced polymers (CFRP), typically employed in different weight-critical applications. Both unidirectional and cross-ply laminates have been studied. The initial failure mode produced depends directly on the beam span- thickness relation. Therefore, specimens with different thicknesses have been analysed for examining the damage initiation due to either the bending moment or the out-of-plane shear load. The experimental description of the damage initiation and evolution has been shown by means of optical microscopy. The good agreement between the analytical estimations and the experimental results shows the validity of the analytical model exposed.

40 CFR 89.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2010 CFR

2010-07-01

... results. 89.509 Section 89.509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Selective Enforcement Auditing § 89.509 Calculation and reporting of test results. (a) Initial test results... rounds these results, in accordance with ASTM E29-93a, to the number of decimal places contained in the...

40 CFR 89.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2012 CFR

2012-07-01

... results. 89.509 Section 89.509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Selective Enforcement Auditing § 89.509 Calculation and reporting of test results. (a) Initial test results... rounds these results, in accordance with ASTM E29-93a, to the number of decimal places contained in the...

40 CFR 89.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2013 CFR

2013-07-01

... results. 89.509 Section 89.509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Selective Enforcement Auditing § 89.509 Calculation and reporting of test results. (a) Initial test results... rounds these results, in accordance with ASTM E29-93a, to the number of decimal places contained in the...

10 CFR 707.13 - Medical review of results of tests for illegal drug use.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Medical review of results of tests for illegal drug use... Procedures § 707.13 Medical review of results of tests for illegal drug use. (a) All test results shall be submitted for medical review by the MRO. A confirmed positive test for drugs shall consist of an initial...

A preliminary study of crack initiation and growth at stress concentration sites

NASA Technical Reports Server (NTRS)

Dawicke, D. S.; Gallagher, J. P.; Hartman, G. A.; Rajendran, A. M.

1982-01-01

Crack initiation and propagation models for notches are examined. The Dowling crack initiation model and the E1 Haddad et al. crack propagation model were chosen for additional study. Existing data was used to make a preliminary evaluation of the crack propagation model. The results indicate that for the crack sizes in the test, the elastic parameter K gave good correlation for the crack growth rate data. Additional testing, directed specifically toward the problem of small cracks initiating and propagating from notches is necessary to make a full evaluation of these initiation and propagation models.

Carpal tunnel syndrome: Investigating the sensitivity of initial-diagnosis with electro-diagnostic tests in 600 cases and associated risk factors especially manual milking.

PubMed

Tunç, Abdulkadir; Güngen, Belma Doğan

2017-01-01

Electro-diagnostic studies are the most reliable methods in diagnosis of carpal tunnel syndrome (CTS). Although there are many risk factors associated with CTS, there are a limited number of studies in the literature indicating that manual milking, which is frequently seen in Turkey, is a risk factor for CTS. The purpose of this study was to evaluate demographic findings of cases referred due to initial diagnosis of CTS as well as aetiological data especially manual milking and to investigate the sensitivity of initial diagnosis of CTS. Six hundred patients, who were referred to our electromyography laboratory due to initial diagnosis of CTS, were included. Demographic findings, duration of complaints, existence of diabetes mellitus, and manual milking histories of all patients were recorded. Sensitivity of initial diagnosis was investigated based on electro-diagnostic test results. According to electro-diagnostic test results, 289 of the patients were diagnosed with CTS (48.17%). 110 (18.3%) of 600 patients had a history of manual milking. In 94 of this group (85.4%), CTS was detected. Statistically significant correlation was found between CTS and age, female gender, duration of complaints, obesity and manual milking. This study confirms that manual milking is an important risk factor for CTS in addition to female gender, age, symptom duration and obesity. The fact that sensitivity of initial diagnosis of CTS was found to be low according to electro-diagnostic test results indicates importance of detailed clinical evaluation.

Pretest analysis document for Test S-FS-6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaw, R.A.; Hall, D.G.

This report documents the pretest analyses completed for Semiscale Test S-FS-6. This test will simulate a transient initiated by a 100% break in a steam generator bottom feedwater line downstream of the check valve. The initial conditions represent normal operating conditions for a C-E System 80 nuclear power plant. Predictions of transients resulting from feedwater line breaks in these plants have indicated that significant primary system overpressurization may occur. The enclosed analyses include a RELAP5/MOD2/CY21 code calculation and preliminary results from a facility hot, integrated test which was conducted to near S-FS-6 specifications. The results of these analyses indicate thatmore » the test objectives for Test S-FS-6 can be achieved. The primary system overpressurization will pose no threat to personnel or plant integrity.« less

Shuttle payload S-band communications system

NASA Technical Reports Server (NTRS)

Batson, B. H.; Teasdale, W. E.; Pawlowski, J. F.; Schmidt, O. L.

1985-01-01

The Shuttle payload S-band communications system design, operational capabilities, and performance are described in detail. System design requirements, overall system and configuration and operation, and laboratory/flight test results are presented. Payload communications requirements development is discussed in terms of evolvement of requirements as well as the resulting technical challenges encountered in meeting the initial requirements. Initial design approaches are described along with cost-saving initiatives that subsequently had to be made. The resulting system implementation that was finally adopted is presented along with a functional description of the system operation. A description of system test results, problems encountered, how the problems were solved, and the system flight experience to date is presented. Finally, a summary of the advancements made and the lessons learned is discussed.

Teledyne Energy Systems, Inc., Proton Exchange Member (PEM) Fuel Cell Engineering Model Powerplant. Test Report: Initial Benchmark Tests in the Original Orientation

NASA Technical Reports Server (NTRS)

Loyselle, Patricia; Prokopius, Kevin

2011-01-01

Proton Exchange Membrane (PEM) fuel cell technology is the leading candidate to replace the alkaline fuel cell technology, currently used on the Shuttle, for future space missions. During a 5-yr development program, a PEM fuel cell powerplant was developed. This report details the initial performance evaluation test results of the powerplant.

Association Between Direct-to-Consumer Advertising and Testosterone Testing and Initiation in the United States, 2009–2013

PubMed Central

Layton, J. Bradley; Kim, Yoonsang; Alexander, G. Caleb; Emery, Sherry L.

2017-01-01

IMPORTANCE Testosterone initiation increased substantially in the United States from 2000 to 2013, especially among men without clear indications. Direct-to-consumer advertising (DTCA) also increased during this time. OBJECTIVE To investigate associations between televised DTCA and testosterone testing and initiation in the United States. DESIGN, SETTING, AND POPULATION Ecologic study conducted in designated market areas (DMAs) in the United States. Monthly testosterone advertising ratings were linked to DMA-level testosterone use data from 2009–2013 derived from commercial insurance claims. Associations between DTCA and testosterone testing, initiation, and initiation without recent baseline tests were estimated using Poisson generalized estimating equations. EXPOSURES Monthly Nielsen ratings for testosterone DTCA in the 75 largest DMAs. MAIN OUTCOMES AND MEASURES (1) Rates of new serum testosterone testing; (2) rates of testosterone initiation (in-office injection, surgical implant, or pharmacy dispensing) for all testosterone products combined and for specific brands; and (3) rates of testosterone initiation without recent serum testosterone testing. RESULTS Of 17 228 599 commercially insured men in the 75 DMAs, 1 007 990 (mean age, 49.6 [SD, 11.5] years) had new serum testosterone tests and 283 317 (mean age, 51.8 [SD, 11.3] years) initiated testosterone treatment. Advertising intensity varied by geographic region and time, with the highest intensity seen in the southeastern United States and with months ranging from no ad exposures to a mean of 13.6 exposures per household. Nonbranded advertisements were common prior to 2012, with branded advertisements becoming more common during and after 2012. Each household advertisement exposure was associated with a monthly increase in rates of new testosterone testing (rate ratio [RR], 1.006; 95% CI, 1.004–1.008), initiation (RR, 1.007; 95% CI, 1.004–1.010), and initiation without a recent test (RR, 1.008; 95% CI, 1.002–1.013). Mean absolute rate increases were 0.14 tests (95% CI, 0.09–0.19), 0.05 new initiations (95% CI, 0.03–0.08), and 0.02 initiations without a recent test (95% CI, 0.01–0.03) per 10 000 men for each monthly ad exposure over the entire period. CONCLUSIONS AND RELEVANCE Among US men residing in the 75 designated market areas, regional exposure to televised direct-to-consumer advertising was associated with greater testosterone testing, new initiation, and initiation without recent testing. PMID:28324090

A Statistical Study on the Effect of Hydrostatic Pressure on Metastable Pitting Corrosion of X70 Pipeline Steel.

PubMed

Yang, Zixuan; Kan, Bo; Li, Jinxu; Qiao, Lijie; Volinsky, Alex A; Su, Yanjing

2017-11-14

Hydrostatic pressure effects on pitting initiation and propagation in X70 steel are investigated by evaluating metastable pitting probability using electrochemical methods and immersion corrosion tests in containing chlorine ion solution. Potentiodynamic tests indicated that hydrostatic pressure can decrease the breakdown potential and lead to a reduced transpassivity region. Metastable test results revealed that hydrostatic pressure can increase metastable pitting formation frequency and promote stabilization of metastable pitting growth. Electrochemical impedance spectroscopy (EIS) results indicate that Hydrostatic pressure decreases the charge transfer resistance and increases the dissolution rate within the cavities. Corrosion test results also indicated that pitting initiation and propagation are accelerated by hydrostatic pressure. Result validity was verified by evaluating metastable pitting to predict pitting corrosion resistance.

A Statistical Study on the Effect of Hydrostatic Pressure on Metastable Pitting Corrosion of X70 Pipeline Steel

PubMed Central

Yang, Zixuan; Kan, Bo; Li, Jinxu; Su, Yanjing; Qiao, Lijie; Volinsky, Alex A.

2017-01-01

Hydrostatic pressure effects on pitting initiation and propagation in X70 steel are investigated by evaluating metastable pitting probability using electrochemical methods and immersion corrosion tests in containing chlorine ion solution. Potentiodynamic tests indicated that hydrostatic pressure can decrease the breakdown potential and lead to a reduced transpassivity region. Metastable test results revealed that hydrostatic pressure can increase metastable pitting formation frequency and promote stabilization of metastable pitting growth. Electrochemical impedance spectroscopy (EIS) results indicate that Hydrostatic pressure decreases the charge transfer resistance and increases the dissolution rate within the cavities. Corrosion test results also indicated that pitting initiation and propagation are accelerated by hydrostatic pressure. Result validity was verified by evaluating metastable pitting to predict pitting corrosion resistance. PMID:29135912

Does universal active MRSA surveillance influence anti-MRSA antibiotic use? A retrospective analysis of the treatment of patients admitted with suspicion of infection at Veterans Affairs Medical Centers between 2005 and 2010

PubMed Central

Jones, Makoto; Huttner, Benedikt; Leecaster, Molly; Huttner, Angela; Damal, Kavitha; Tanner, Windy; Nielson, Christopher; Rubin, Michael A.; Goetz, Matthew Bidwell; Madaras-Kelly, Karl; Samore, Matthew H.

2014-01-01

Objectives After the implementation of an active surveillance programme for MRSA in US Veterans Affairs (VA) Medical Centers, there was an increase in vancomycin use. We investigated whether positive MRSA admission surveillance tests were associated with MRSA-positive clinical admission cultures and whether the availability of surveillance tests influenced prescribers' ability to match initial anti-MRSA antibiotic use with anticipated MRSA results from clinical admission cultures. Methods Analyses were based on barcode medication administration data, microbiology data and laboratory data from 129 hospitals between January 2005 and September 2010. Hospitalized patient admissions were included if clinical cultures were obtained and antibiotics started within 2 days of admission. Mixed-effects logistic regression was used to examine associations between positive MRSA admission cultures and (i) admission MRSA surveillance test results and (ii) initial anti-MRSA therapy. Results Among 569 815 included admissions, positive MRSA surveillance tests were strong predictors of MRSA-positive admission cultures (OR 8.5; 95% CI 8.2–8.8). The negative predictive value of MRSA surveillance tests was 97.6% (95% CI 97.5%–97.6%). The diagnostic OR between initial anti-MRSA antibiotics and MRSA-positive admission cultures was 3.2 (95% CI 3.1–3.4) for patients without surveillance tests and was not significantly different for admissions with surveillance tests. Conclusions The availability of nasal MRSA surveillance tests in VA hospitals did not seem to improve the ability of prescribers to predict the necessity of initial anti-MRSA treatment despite the high negative predictive value of MRSA surveillance tests. Prospective trials are needed to establish the safety and effectiveness of using MRSA surveillance tests to guide antibiotic therapy. PMID:25103488

Tension and Bending Testing of an Integral T-Cap for Stitched Composite Airframe Joints

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.; Leone, Frank A., Jr.

2016-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body aircraft configuration. An important design feature required for assembly is the integrally stitched T-cap, which provides connectivity of the corner (orthogonal) joint between adjacent panels. A series of tests were conducted on T-cap test articles, with and without a rod stiffener penetrating the T-cap web, under tension (pull-off) and bending loads. Three designs were tested, including the baseline design used in large-scale test articles. The baseline had only the manufacturing stitch row adjacent to the fillet at the base of the T-cap web. Two new designs added stitching rows to the T-cap web at either 0.5- or 1.0-inch spacing along the height of the web. Testing was conducted at NASA Langley Research Center to determine the behavior of the T-cap region resulting from the applied loading. Results show that stitching arrests the initial delamination failures so that the maximum strength capability exceeds the load at which the initial delaminations develop. However, it was seen that the added web stitching had very little effect on the initial delamination failure load, but actually decreased the initial delamination failure load for tension loading of test articles without a stiffener passing through the web. Additionally, the added web stitching only increased the maximum load capability by between 1% and 12.5%. The presence of the stiffener, however, did increase the initial and maximum loads for both tension and bending loading as compared to the stringerless baseline design. Based on the results of the few samples tested, the additional stitching in the T-cap web showed little advantage over the baseline design in terms of structural failure at the T-cap web/skin junction for the current test articles.

Predicting future protection of respirator users: Statistical approaches and practical implications.

PubMed

Hu, Chengcheng; Harber, Philip; Su, Jing

2016-01-01

The purpose of this article is to describe a statistical approach for predicting a respirator user's fit factor in the future based upon results from initial tests. A statistical prediction model was developed based upon joint distribution of multiple fit factor measurements over time obtained from linear mixed effect models. The model accounts for within-subject correlation as well as short-term (within one day) and longer-term variability. As an example of applying this approach, model parameters were estimated from a research study in which volunteers were trained by three different modalities to use one of two types of respirators. They underwent two quantitative fit tests at the initial session and two on the same day approximately six months later. The fitted models demonstrated correlation and gave the estimated distribution of future fit test results conditional on past results for an individual worker. This approach can be applied to establishing a criterion value for passing an initial fit test to provide reasonable likelihood that a worker will be adequately protected in the future; and to optimizing the repeat fit factor test intervals individually for each user for cost-effective testing.

Progressing From Initially Ambiguous Functional Analyses: Three Case Examples

PubMed Central

Tiger, Jeffrey H.; Fisher, Wayne W.; Toussaint, Karen A.; Kodak, Tiffany

2009-01-01

Most often functional analyses are initiated using a standard set of test conditions, similar to those described by Iwata, Dorsey, Slifer, Bauman, and Richman (1982/1994). These test conditions involve the careful manipulation of motivating operations, discriminative stimuli, and reinforcement contingencies to determine the events related to the occurrence and maintenance of problem behavior. Some individuals display problem behavior that is occasioned and reinforced by idiosyncratic or otherwise unique combinations of environmental antecedents and consequences of behavior, which are unlikely to be detected using these standard assessment conditions. For these individuals, modifications to the standard test conditions or the inclusion of novel test conditions may result in clearer assessment outcomes. The current study provides three case examples of individuals whose functional analyses were initially undifferentiated; however, modifications to the standard conditions resulted in the identification of behavioral functions and the implementation of effective function-based treatments. PMID:19233611

Pitting Initiation and Propagation of X70 Pipeline Steel Exposed to Chloride-Containing Environments

PubMed Central

Yang, Zixuan; Kan, Bo; Li, Jinxu; Su, Yanjing; Qiao, Lijie; Volinsky, Alex A.

2017-01-01

Inclusion-induced pitting initiation mechanisms in X70 steel were investigated by scanning electron microscopy, scanning Kelvin probe force microscopy (SKPFM), immersion and electrochemical polarization tests in chloride-containing ion solutions. There are three inclusion types in the X70 steel. Corrosion test results indicated that pitting corrosion resistance of type A inclusion < type C inclusion < type B inclusion, i.e., (Mn, Ca)S < matrix < (Al, Ca)O. SKPFM test results show that the type A inclusion exhibited both lower and higher potentials than the matrix, while the type B inclusion exhibited higher potential than the matrix. The corrosion test and the SKPFM potential test results are consistent. Potentiodynamic polarization results indicate that the type A and C are active inclusions, while the type B is an inactive inclusion. Three kinds of possible mechanisms of inclusion-induced pitting corrosion are established for the X70 steel. PMID:28902156

The Collection of Ice in Jet A-1 Fuel Pipes

NASA Astrophysics Data System (ADS)

Maloney, Thomas C.

Ice collection and blockages in fuel systems have been of interest to the aerospace community since their discovery in the late 1950's when a B-52 crashed. A recent growth of interest was provoked by several incidents that occurred within the last few years. This study seeks to understand the underlying principles of ice growth in fuel flow systems. Tests were performed in a recirculated fuel system with a fuel tank that held approximately 115 gallons of Jet A-1 fuel and ice accumulation was observed in two removable test pipes. The setup was in an altitude chamber capable of -60 °F and the experiments involved full scale flow components. Initially, tests were done to better understand the system and variables that effected accumulation. First, initial conditions within the test pipes were varied. Next, pipe geometry, pipe surface properties, initial water content of the fuel and heat transfer from the fuel pipe were varied. As a result of the tests, observations were made about other effects involved in the study. The effects include: the result of sequentially run tests, the effect of the fuel on the freezing temperature of the entrained water, the effect of ice accumulation on pipe welds, and the effect of the test pipe entrance and exit flow conditions on ice accumulation. The results of initial tests were qualitative. Later quantitative tests were done to demonstrate the dependence of temperature, Reynolds number, and heat transfer on ice accumulation. Tests were quantified with a pressure increase across the pipe sections that was normalized by the expected theoretical initial pressure. As a result of these tests the effect of contamination in the fuel was revealed. For ease of reference, the initial tests were called "stage I" and the later tests were called "stage II". The results of stage I showed that accumulation of soft ice was greatest when a layer of hard ice had initially formed on the pipe surface. Stainless steel collected more ice than Teflon® and there was a lack of a preferential accumulation region downstream of a pipe bend. A greater heat transfer from the pipe increased ice accumulation for aluminum that was made rough with 80 grit sand paper, and for Teflon®. Water was shown to collect in the pipe system as the number of tests increased and the freeze temperature of either the hard or soft ice was about 0 °C. Finally, results of "stage I" tests showed that stainless steel pipe welds were a preferred sight for ice to accumulate. Repeatability was done first in stage II and the normalized pressure increase for two 3/42 un-insulated pipe tests were within 7%. Normalized pressure increase across a pipe was shown to increase as Reynolds number decreased. A 50% increase in Reynolds number led to a 40% decrease in characteristic normalized pressure increase (CNPI). Tests were done at three temperatures and ice accumulated the most at -11 °C. The CNPI at -11 °C was about three times greater than the CNPI at -7.4 °C and about sixty times greater than the CNPI at -19.4 C. A greater heat transfer from the fuel pipe increased ice accumulation. For the amount of time that the tests ran, the total normalized pressure increase was about .9 greater for an un-insulated pipe than for an insulated pipe. Contamination in the fuel increased the amount of soft ice that collected in the system. The CNPI for the more contaminated fuel was more than double the case with less contaminated fuel. Possible solutions for the prevention or decrease of ice accumulation in aircraft fuel systems based on the results of this study are insulated pipes, a change in the type of pipe material, a higher fuel flow rate and cleaner fuel. The fuel temperature could also be altered to avoid temperatures where the most ice accumulates.

Decomposing the interaction between retention interval and study/test practice: The role of retrievability

PubMed Central

Jang, Yoonhee; Wixted, John T.; Pecher, Diane; Zeelenberg, René; Huber, David E.

2012-01-01

Even without feedback, test practice enhances delayed performance compared to study practice, but the size of the effect is variable across studies. We investigated the benefit of testing, separating initially retrievable items from initially non-retrievable items. In two experiments, an initial test determined item retrievability. Retrievable or non-retrievable items were subsequently presented for repeated study or test practice. Collapsing across items, in Experiment 1, we obtained the typical crossover interaction between retention interval and practice type. For retrievable items, however, the crossover interaction was quantitatively different, with a small study benefit for an immediate test and a larger testing benefit after a delay. For non-retrievable items, there was a large study benefit for an immediate test, but one week later there was no difference between the study and test practice conditions. In Experiment 2, initially non-retrievable items were given additional study followed by either an immediate test or even more additional study, and one week later performance did not differ between the two conditions. These results indicate that the effect size of study/test practice is due to the relative contribution of retrievable and non-retrievable items. PMID:22304454

Decomposing the interaction between retention interval and study/test practice: the role of retrievability.

PubMed

Jang, Yoonhee; Wixted, John T; Pecher, Diane; Zeelenberg, René; Huber, David E

2012-01-01

Even without feedback, test practice enhances delayed performance compared to study practice, but the size of the effect is variable across studies. We investigated the benefit of testing, separating initially retrievable items from initially nonretrievable items. In two experiments, an initial test determined item retrievability. Retrievable or nonretrievable items were subsequently presented for repeated study or test practice. Collapsing across items, in Experiment 1, we obtained the typical cross-over interaction between retention interval and practice type. For retrievable items, however, the cross-over interaction was quantitatively different, with a small study benefit for an immediate test and a larger testing benefit after a delay. For nonretrievable items, there was a large study benefit for an immediate test, but one week later there was no difference between the study and test practice conditions. In Experiment 2, initially nonretrievable items were given additional study followed by either an immediate test or even more additional study, and one week later performance did not differ between the two conditions. These results indicate that the effect size of study/test practice is due to the relative contribution of retrievable and nonretrievable items.

Proof of concept testing report.

DOT National Transportation Integrated Search

2008-09-17

This report documents the methodology and results of the U.S. Department of : Transportation (USDOT) Next Generation 9-1-1 Initiative (NG9-1-1) Proof of Concept : (POC) testing. It describes in detail the NG9-1-1 POC test results and provides a basel...

Initial test results with a single-cylinder rhombic-drive Stirling engine. [to be applied to automobile engine design to conserve energy

NASA Technical Reports Server (NTRS)

Cairelli, J. E.; Thieme, L. G.; Walter, R. J.

1978-01-01

A 6 kW (8 hp), single-cylinder, rhombic-drive Stirling engine was restored to operating condition, and preliminary characterization tests run with hydrogen and helium as the working gases. Initial tests show the engine brake specific fuel consumption (BSFC) with hydrogen working gas to be within the range of BSFC observed by the Army at Fort Belvoir, Virginia, in 1966. The minimum system specific fuel consumption (SFC) observed during the initial tests with hydrogen was 669 g/kW hr (1.1 lb/hpx hr), compared with 620 g/kWx hr (1.02 lb/hpx hr) for the Army tests. However, the engine output power for a given mean compression-space pressure was lower than for the Army tests. The observed output power at a working-space pressure of 5 MPa (725 psig) was 3.27 kW (4.39 hp) for the initial tests and 3.80 kW (5.09 hp) for the Army tests. As expected, the engine power with helium was substantially lower than with hydrogen.

Comparison of turnaround time and total cost of HIV testing before and after implementation of the 2014 CDC/APHL Laboratory Testing Algorithm for diagnosis of HIV infection.

PubMed

Chen, Derrick J; Yao, Joseph D

2017-06-01

Updated recommendations for HIV diagnostic laboratory testing published by the Centers for Disease Control and Prevention and the Association of Public Health Laboratories incorporate 4th generation HIV immunoassays, which are capable of identifying HIV infection prior to seroconversion. The purpose of this study was to compare turnaround time and cost between 3rd and 4th generation HIV immunoassay-based testing algorithms for initially reactive results. The clinical microbiology laboratory database at Mayo Clinic, Rochester, MN was queried for 3rd generation (from November 2012 to May 2014) and 4th generation (from May 2014 to November 2015) HIV immunoassay results. All results from downstream supplemental testing were recorded. Turnaround time (defined as the time of initial sample receipt in the laboratory to the time the final supplemental test in the algorithm was resulted) and cost (based on 2016 Medicare reimbursement rates) were assessed. A total of 76,454 and 78,998 initial tests were performed during the study period using the 3rd generation and 4th generation HIV immunoassays, respectively. There were 516 (0.7%) and 581 (0.7%) total initially reactive results, respectively. Of these, 304 (58.9%) and 457 (78.7%) were positive by supplemental testing. There were 10 (0.01%) cases of acute HIV infection identified with the 4th generation algorithm. The most frequent tests performed to confirm an HIV-positive case using the 3rd generation algorithm, which were reactive initial immunoassay and positive HIV-1 Western blot, took a median time of 1.1 days to complete at a cost of $45.00. In contrast, the most frequent tests performed to confirm an HIV-positive case using the 4th generation algorithm, which included a reactive initial immunoassay and positive HIV-1/-2 antibody differentiation immunoassay for HIV-1, took a median time of 0.4 days and cost $63.25. Overall median turnaround time was 2.2 and 1.5 days, and overall median cost was $63.90 and $72.50 for 3rd and 4th generation algorithms, respectively. Both 3rd and 4th generation HIV immunoassays had similar total numbers of tests performed and positivity rates during the study period. A greater proportion of reactive 4th generation immunoassays were confirmed to be positive, and the 4th generation algorithm identified several cases of acute HIV infection that would have been missed by the 3rd generation algorithm. The 4th generation algorithm had a more rapid turnaround time but higher cost for confirmed positive HIV infections and overall, compared to the 3rd generation algorithm. Copyright © 2017 Elsevier B.V. All rights reserved.

T-Cap Pull-Off and Bending Behavior for Stitched Structure

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.; Leone, Frank A., Jr.

2016-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body aircraft configuration. An important design feature required for assembly is the integrally stitched T-cap, which provides connectivity of the corner (orthogonal) joint between adjacent panels. A series of tests were conducted on T-cap test articles, with and without a rod stiffener penetrating the T-cap web, under tension (pull-off) and bending loads. Three designs were tested, including the baseline design used in largescale test articles. The baseline had only the manufacturing stitch row adjacent to the fillet at the base of the T-cap web. Two new designs added stitching rows to the T-cap web at either 0.5- or 1.0-inch spacing along the height of the web. Testing was conducted at NASA Langley Research Center to determine the behavior of the T-cap region resulting from the applied loading. Results show that stitching arrests the initial delamination failures so that the maximum strength capability exceeds the load at which the initial delaminations develop. However, it was seen that the added web stitching had very little effect on the initial delamination failure load, but actually decreased the initial delamination failure load for tension loading of test articles without a stiffener passing through the web. Additionally, the added web stitching only increased the maximum load capability by between 1% and 12.5%. The presence of the stiffener, however, did increase the initial and maximum loads for both tension and bending loading as compared to the stringerless baseline design. Based on the results of the few samples tested, the additional stitching in the T-cap web showed little advantage over the baseline design in terms of structural failure at the T-cap web/skin junction for the current test articles.

Resource Prospector Propulsion Cold Flow Test

NASA Technical Reports Server (NTRS)

Williams, Hunter; Pederson, Kevin; Dervan, Melanie; Holt, Kimberly; Jernigan, Frankie; Trinh, Huu; Flores, Sam

2014-01-01

For the past year, NASA Marshall Space Flight Center and Johnson Space Center have been working on a government version of a lunar lander design for the Resource Prospector Mission. A propulsion cold flow test system, representing an early flight design of the propulsion system, has been fabricated. The primary objective of the cold flow test is to simulate the Resource Prospector propulsion system operation through water flow testing and obtain data for anchoring analytical models. This effort will also provide an opportunity to develop a propulsion system mockup to examine hardware integration to a flight structure. This paper will report the work progress of the propulsion cold flow test system development and test preparation. At the time this paper is written, the initial waterhammer testing is underway. The initial assessment of the test data suggests that the results are as expected and have a similar trend with the pretest prediction. The test results will be reported in a future conference.

Pretest analysis document for Test S-FS-7

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hall, D.G.

This report documents the pretest calculations completed for Semiscale Test S-FS-7. This test will simulate a transient initiated by a 14.3% break in a steam generator bottom feedwater line downstream of the check valve. The initial conditions represent normal operating conditions for a C-E System 80 nuclear power plant. Predictions of transients resulting from feedwater line breaks in these plants have indicated that significant primary system overpressurization may occur. The results of a RELAP5/MOD2/CY21 code calculation indicate that the test objectives for Test S-FS-7 can be achieved. The primary system overpressurization will occur but pose no threat to personnel ormore » to plant integrity. 3 refs., 15 figs., 5 tabs.« less

Pretest analysis document for Test S-FS-11

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hall, D.G.; Shaw, R.A.

This report documents the pretest calculations completed for Semiscale Test S-FS-11. This test will simulate a transient initiated by a 50% break in a steam generator bottom feedwater line downstream of the check valve. The initial conditions represents normal operating conditions for a C-E System 80 nuclear plant. Prediction of transients resulting from feedwater line breaks in these plants have indicated that significant primary system overpressurization may occur. The results of a RELAP5/MOD2/CY21 code calculation indicate that the test objectives for Test S-FS-11 can be achieved. The primary system overpressurization will occur but pose no threat to personnel or plantmore » integrity. 3 refs., 15 figs., 5 tabs.« less

Effective Inertial Frame in an Atom Interferometric Test of the Equivalence Principle

NASA Astrophysics Data System (ADS)

Overstreet, Chris; Asenbaum, Peter; Kovachy, Tim; Notermans, Remy; Hogan, Jason M.; Kasevich, Mark A.

2018-05-01

In an ideal test of the equivalence principle, the test masses fall in a common inertial frame. A real experiment is affected by gravity gradients, which introduce systematic errors by coupling to initial kinematic differences between the test masses. Here we demonstrate a method that reduces the sensitivity of a dual-species atom interferometer to initial kinematics by using a frequency shift of the mirror pulse to create an effective inertial frame for both atomic species. Using this method, we suppress the gravity-gradient-induced dependence of the differential phase on initial kinematic differences by 2 orders of magnitude and precisely measure these differences. We realize a relative precision of Δ g /g ≈6 ×10-11 per shot, which improves on the best previous result for a dual-species atom interferometer by more than 3 orders of magnitude. By reducing gravity gradient systematic errors to one part in 1 013 , these results pave the way for an atomic test of the equivalence principle at an accuracy comparable with state-of-the-art classical tests.

Passenger rail train-to-train impact test. Volume 1 : overview and selected results

DOT National Transportation Integrated Search

2003-07-01

This report describes the results of the train-to-train impact test conducted at the Federal Railroad Administration's Transportation Technology Center in Pueblo, Colorado on January 31, 2002. In this test, a cab car-led train, initially moving at 30...

Initial Navigation Alignment of Optical Instruments on GOES-R

NASA Technical Reports Server (NTRS)

Isaacson, Peter J.; DeLuccia, Frank J.; Reth, Alan D.; Igli, David A.; Carter, Delano R.

2016-01-01

Post-launch alignment errors for the Advanced Baseline Imager (ABI) and Geospatial Lightning Mapper (GLM) on GOES-R may be too large for the image navigation and registration (INR) processing algorithms to function without an initial adjustment to calibration parameters. We present an approach that leverages a combination of user-selected image-to-image tie points and image correlation algorithms to estimate this initial launch-induced offset and calculate adjustments to the Line of Sight Motion Compensation (LMC) parameters. We also present an approach to generate synthetic test images, to which shifts and rotations of known magnitude are applied. Results of applying the initial alignment tools to a subset of these synthetic test images are presented. The results for both ABI and GLM are within the specifications established for these tools, and indicate that application of these tools during the post-launch test (PLT) phase of GOES-R operations will enable the automated INR algorithms for both instruments to function as intended.

United States Air Force F-35A Operational Basing Environmental Impact Statement. Volume 1

DTIC Science & Technology

2013-09-01

Evaluation (FDE) program and Weapons School (WS) beddown, the F-22 designator was used. Subsequent testing , development, and deployment resulted in...Initial F-35A Operational Basing EIS Final, September 2013 contract to develop the JSF ( designated the F-35 Lightning II). Since then, testing of F...of the aircraft even with system failures. Throughout the design and testing process, safety initiatives took previous best practices for single

Study of voltage decrease in organic light emitting diodes during the initial stage of lifetime

NASA Astrophysics Data System (ADS)

Cusumano, P.

2016-02-01

We report the results of lifetime DC testing at constant current of not-encapsulated organic light emitting diodes (OLEDs) based on Tris (8 idroxyquinoline) aluminum (Alq3) as emitting material. In particular, a voltage decrease during the initial stage of the lifetime test is observed. The cause of this behavior is also discussed, mainly linked to initial Joule self-heating of the device, rising its temperature above room temperature until thermal equilibrium is reached at steady state.

Experimental Evaluation of Fatigue Crack Initiation from Corroded Hemispherical Notches in Aerospace Structural Materials

NASA Technical Reports Server (NTRS)

Garcia, Daniel B.; Forman, Royce; Shindo, David

2010-01-01

A test program was developed and executed to evaluate the influence of corroded hemispherical notches on the fatigue crack initiation and propagation in aluminum 7075-T7351, 4340 steel, and D6AC steel. Surface enhancements such as shot peening and laser shock peening were also incorporated as part of the test effort with the intent of improving fatigue performance. In addition to the testing, fracture mechanics and endurance limit based analysis methods were evaluated to characterize the results with the objective of challenging typical assumptions used in modeling fatigue cracks from corrosion pits. The results specifically demonstrate that the aluminum and steel alloys behave differently with respect to fatigue crack initiation from hemispherical corrosion pits. The aluminum test results were bounded by the fracture mechanics and endurance limit models while exhibiting a general insensitivity to the residual stress field generated by shot peening. The steel specimens were better characterized by the endurance limit fatigue properties and did exhibit sensitivities to residual stresses from the shot peening and laser shock peening

Test--retest variability of Randot stereoacuity measures gathered in an unselected sample of UK primary school children.

PubMed

Adler, Paul; Scally, Andrew J; Barrett, Brendan T

2012-05-01

To determine the test-retest reliability of the Randot stereoacuity test when used as part of vision screening in schools. Randot stereoacuity (graded-circles) and logMAR visual acuity measures were gathered in an unselected sample of 139 children (aged 4-12, mean 8.1±2.1 years) in two schools. Randot testing was repeated on two occasions (average interval between successive tests 8 days, range: 1-21 days). Three Randot scores were obtained in 97.8% of children. Randot stereoacuity improved by an average of one plate (ie, one test level) on repeat testing but was little changed when tested on the third occasion. Within-subject variability was up to three test levels on repeat testing. When stereoacuity was categorised as 'fine', 'intermediate' or 'coarse', the greatest variability was found among younger children who exhibited 'intermediate' or 'coarse'/nil stereopsis on initial testing. Whereas 90.8% of children with 'fine' stereopsis (≤50 arc-seconds) on the first test exhibited 'fine' stereopsis on both subsequent tests, only ∼16% of children with 'intermediate' (>50 but ≤140 arc-seconds) or 'coarse'/nil (≥200 arc-seconds) stereoacuity on initial testing exhibited stable test results on repeat testing. Children exhibiting abnormal stereoacuity on initial testing are very likely to exhibit a normal result when retested. The value of a single, abnormal Randot graded-circles stereoacuity measure from school screening is therefore questionable.

"None of the above" as a correct and incorrect alternative on a multiple-choice test: implications for the testing effect.

PubMed

Odegard, Timothy N; Koen, Joshua D

2007-11-01

Both positive and negative testing effects have been demonstrated with a variety of materials and paradigms (Roediger & Karpicke, 2006b). The present series of experiments replicate and extend the research of Roediger and Marsh (2005) with the addition of a "none-of-the-above" response option. Participants (n=32 in both experiments) read a set of passages, took an initial multiple-choice test, completed a filler task, and then completed a final cued-recall test (Experiment 1) or multiple-choice test (Experiment 2). Questions were manipulated on the initial multiple-choice test by adding a "none-of-the-above" response alternative (choice "E") that was incorrect ("E" Incorrect) or correct ("E" Correct). The results from both experiments demonstrated that the positive testing effect was negated when the "none-of-the-above" alternative was the correct response on the initial multiple-choice test, but was still present when the "none-of-the-above" alternative was an incorrect response.

Safety of falciparum malaria diagnostic strategy based on rapid diagnostic tests in returning travellers and migrants: a retrospective study

PubMed Central

2012-01-01

Background Rapid diagnostic tests for malaria (RDTs) allow accurate diagnosis and prompt treatment. Validation of their usefulness in travellers with fever was needed. The safety of a strategy to diagnose falciparum malaria based on RDT followed by immediate or delayed microscopy reading at first attendance was evaluated in one referral hospital in Switzerland. Methods A retrospective study was conducted in the outpatient clinic and emergency ward of University Hospital, covering a period of eight years (1999–2007). The study was conducted in the outpatient clinic and emergency ward of University Hospital. All adults suspected of malaria with a diagnostic test performed were included. RDT and microscopy as immediate tests were performed during working hours, and RDT as immediate test and delayed microscopy reading out of laboratory working hours. The main outcome measure was occurrence of specific complications in RDT negative and RDT positive adults. Results 2,139 patients were recruited. 1987 had both initial RDT and blood smear (BS) result negative. Among those, 2/1987 (0.1%) developed uncomplicated malaria with both RDT and BS positive on day 1 and day 6 respectively. Among the 152 patients initially malaria positive, 137 had both RDT and BS positive, four only BS positive and five only RDT positive (PCR confirmed) (six had only one test performed). None of the four initially RDT negative/BS positive and none of the five initially BS negative/RDT positive developed severe malaria while 6/137 of both RDT and BS positive did so. The use of RDT allowed a reduction of a median of 2.1 hours to get a first malaria test result. Conclusions A malaria diagnostic strategy based on RDTs and a delayed BS is safe in non-immune populations, and shortens the time to first malaria test result. PMID:23158019

40 CFR 92.508 - Calculation and reporting of test results.

Code of Federal Regulations, 2014 CFR

2014-07-01

... expressed to one additional significant figure. (b) Final test results shall be calculated by summing the... contained in the applicable standard expressed to one additional significant figure. (c) Manufacturers and... additional significant figure. (d) If, subsequent to an initial failure of a production line test, the...

40 CFR 92.508 - Calculation and reporting of test results.

Code of Federal Regulations, 2011 CFR

2011-07-01

... expressed to one additional significant figure. (b) Final test results shall be calculated by summing the... contained in the applicable standard expressed to one additional significant figure. (c) Manufacturers and... additional significant figure. (d) If, subsequent to an initial failure of a production line test, the...

Fatigue crack identification method based on strain amplitude changing

NASA Astrophysics Data System (ADS)

Guo, Tiancai; Gao, Jun; Wang, Yonghong; Xu, Youliang

2017-09-01

Aiming at the difficulties in identifying the location and time of crack initiation in the castings of helicopter transmission system during fatigue tests, by introducing the classification diagnostic criteria of similar failure mode to find out the similarity of fatigue crack initiation among castings, an engineering method and quantitative criterion for detecting fatigue cracks based on strain amplitude changing is proposed. This method is applied on the fatigue test of a gearbox housing, whose results indicates: during the fatigue test, the system alarms when SC strain meter reaches the quantitative criterion. The afterwards check shows that a fatigue crack less than 5mm is found at the corresponding location of SC strain meter. The test result proves that the method can provide accurate test data for strength life analysis.

The effects of free recall testing on subsequent source memory.

PubMed

Brewer, Gene A; Marsh, Richard L; Meeks, Joseph T; Clark-Foos, Arlo; Hicks, Jason L

2010-05-01

The testing effect is the finding that prior retrieval of information from memory will result in better subsequent memory for that material. One explanation for these effects is that initial free recall testing increases the recollective details for tested information, which then becomes more available during a subsequent test phase. In three experiments we explored this hypothesis using a source-monitoring test phase after the initial free recall tests. We discovered that memory is differentially enhanced for certain recollective details depending on the nature of the free recall task. Thus further research needs to be conducted to specify how different kinds of memorial details are enhanced by free recall testing.

DSN radio science system design and testing for Voyager-Neptune encounter

NASA Technical Reports Server (NTRS)

Ham, N. C.; Rebold, T. A.; Weese, J. F.

1989-01-01

The Deep Space Network (DSN) Radio Science System presently implemented within the Deep Space Network was designed to meet stringent requirements imposed by the demands of the Voyager-Neptune encounter and future missions. One of the initial parameters related to frequency stability is discussed. The requirement, specification, design, and methodology for measuring this parameter are described. A description of special instrumentation that was developed for the test measurements and initial test data resulting from the system tests performed at Canberra, Australia and Usuda, Japan are given.

Recent High Heat Flux Tests on W-Rod-Armored Mockups

DOE Office of Scientific and Technical Information (OSTI.GOV)

NYGREN,RICHARD E.; YOUCHISON,DENNIS L.; MCDONALD,JIMMIE M.

2000-07-18

In the authors initial high heat flux tests on small mockups armored with W rods, done in the small electron beam facility (EBTS) at Sandia National Laboratories, the mockups exhibited excellent thermal performance. However, to reach high heat fluxes, they reduced the heated area to only a portion ({approximately}25%) of the sample. They have now begun tests in their larger electron beam facility, EB 1200, where the available power (1.2 MW) is more than enough to heat the entire surface area of the small mockups. The initial results indicate that, at a given power, the surface temperatures of rods inmore » the EB 1200 tests is somewhat higher than was observed in the EBTS tests. Also, it appears that one mockup (PW-10) has higher surface temperatures than other mockups with similar height (10mm) W rods, and that the previously reported values of absorbed heat flux on this mockup were too high. In the tests in EB 1200 of a second mockup, PW-4, absorbed heat fluxes of {approximately}22MW/m{sup 2} were reached but the corresponding surface temperatures were somewhat higher than in EBTS. A further conclusion is that the simple 1-D model initially used in evaluating some of the results from the EBTS testing was not adequate, and 3-D thermal modeling will be needed to interpret the results.« less

Series-Bosch Technology for Oxygen Recovery During Lunar or Martian Surface Missions

NASA Technical Reports Server (NTRS)

Abney, Morgan B.; Mansell, J. Matthew; Rabenberg, Ellen; Stanley, Christine M.; Edmunson, Jennifer; Alleman, James E.; Chen, Kevin; Dumez, Sam

2014-01-01

Long-duration surface missions to the Moon or Mars will require life support systems that maximize resource recovery to minimize resupply from Earth. To address this need, NASA previously proposed a Series-Bosch (S-Bosch) oxygen recovery system, based on the Bosch process, which can theoretically recover 100% of the oxygen from metabolic carbon dioxide. Bosch processes have the added benefits of the potential to recover oxygen from atmospheric carbon dioxide and the use of regolith materials as catalysts, thereby eliminating the need for catalyst resupply from Earth. In 2012, NASA completed an initial design for an S-Bosch development test stand that incorporates two catalytic reactors in series including a Reverse Water-Gas Shift (RWGS) Reactor and a Carbon Formation Reactor (CFR). In 2013, fabrication of system components, with the exception of a CFR, and assembly of the test stand was initiated. Stand-alone testing of the RWGS reactor was completed to compare performance with design models. Continued testing of Lunar and Martian regolith simulants provided sufficient data to design a CFR intended to utilize these materials as catalysts. Finally, a study was conducted to explore the possibility of producing bricks from spent regolith catalysts. The results of initial demonstration testing of the RWGS reactor, results of continued catalyst performance testing of regolith simulants, and results of brick material properties testing are reported. Additionally, design considerations for a regolith-based CFR are discussed.

Series-Bosch Technology for Oxygen Recovery During Lunar or Martian Surface Missions

NASA Technical Reports Server (NTRS)

Abney, Morgan B.; Mansell, James M.; Stanley, Christine; Edmunson, Jennifer; Dumez, Samuel; Chen, Kevin; Alleman, James E.

2014-01-01

Long-duration surface missions to the Moon or Mars will require life support systems that maximize resource recovery to minimize resupply from Earth. To address this need, NASA previously proposed a Series-Bosch (S-Bosch) oxygen recovery system, based on the Bosch process, which can theoretically recover 100% of the oxygen from metabolic carbon dioxide. Bosch processes have the added benefits of the potential to recover oxygen from atmospheric carbon dioxide and the use of regolith materials as catalysts, thereby eliminating the need for catalyst resupply from Earth. In 2012, NASA completed an initial design for an S-Bosch development test stand that incorporates two catalytic reactors in series including a Reverse Water-Gas Shift (RWGS) Reactor and a Carbon Formation Reactor (CFR). In 2013, fabrication of system components, with the exception of a CFR, and assembly of the test stand was initiated. Stand-alone testing of the RWGS reactor was completed to compare performance with design models. Continued testing of Lunar and Martian regolith simulants provided sufficient data to design a CFR intended to utilize these materials as catalysts. Finally, a study was conducted to explore the possibility of producing bricks from spend regolith catalysts. The results of initial demonstration testing of the RWGS reactor, results of continued catalyst performance testing of regolith simulants, and results of brick material properties testing are reported. Additionally, design considerations for a regolith-based CFR are discussed.

The chocolate-colored expanse of Rogers Dry Lake frames the sleek lines of the Boeing / NASA X-48B subscale demonstrator during a test flight at Edwards AFB

NASA Image and Video Library

2007-08-14

Boeing Phantom Works' subscale Blended Wing Body technology demonstration aircraft began its initial flight tests from NASA's Dryden Flight Research Center at Edwards Air Force Base, Calif. in the summer of 2007. The 8.5 percent dynamically scaled unmanned aircraft, designated the X-48B by the Air Force, is designed to mimic the aerodynamic characteristics of a full-scale large cargo transport aircraft with the same blended wing body shape. The initial flight tests focused on evaluation of the X-48B's low-speed flight characteristics and handling qualities. About 25 flights were planned to gather data in these low-speed flight regimes. Based on the results of the initial flight test series, a second set of flight tests was planned to test the aircraft's low-noise and handling characteristics at transonic speeds.

Effect of Shockwave Curvature on Run Distance Observed with a Modified Wedge Test

NASA Astrophysics Data System (ADS)

Lee, Richard; Dorgan, Robert; Sutherland, Gerrit; Benedetta, Ashley; Milby, Christopher

2011-06-01

The effect of wave curvature on shock initiation in PBXN-110 was investigated using a modified wedge test configuration. Various thicknesses of PBXN-110 donor slabs were used to define the shockwave curvature introduced to wedge samples of the same explosive. The donor slabs were initiated with line-wave generators so that the introduced shock would be the same shape, magnitude and duration across the entire input surface of the wedge. The shock parameters were varied for a given donor thickness via different widths of PMMA spacers placed between the donor and the wedge. A framing camera was used to observe where initiation occurred along the face of the wedge. Initiation always occurred at the center of the shock front instead of the sides like that reported by others using a much smaller test format. Results were compared to CTH calculations to indicate if there were effects associated with highly curved shock fronts that could not be adequately predicted. The run distance predicted in CTH for a 50.8 mm thick donor slab (low curvature) compared favorably with experimental results. However, results from thinner donor slabs (higher curvature) indicate a more sensitive behavior than the simulations predicted.

Effect of shockwave curvature on run distance observed with a modified wedge test

NASA Astrophysics Data System (ADS)

Lee, Richard; Dorgan, Robert J.; Sutherland, Gerrit; Benedetta, Ashley; Milby, Christopher

2012-03-01

The effect of wave curvature on shock initiation in PBXN-110 was investigated using a modified wedge test configuration. Various widths of PBXN-110 donor slabs were used to define the shockwave curvature introduced to wedge samples of the same explosive. The donor slabs were initiated with line-wave generators so that the shock from the donor would be the same shape, magnitude and duration across the entire input surface of the wedge. The shock parameters were varied for a given donor with PMMA spacers placed between the donor and the wedge sample. A high-speed electronic framing camera was used to observe where initiation occurred along the face of the wedge. Initiation always occurred at the center of the shock front instead of along the sides like that reported by others using a much smaller test format. Results were compared to CTH calculations to indicate if there were effects associated with highly curved shock fronts that could not be adequately predicted. The run distance predicted in CTH for a 50.8 mm wide donor slab (low curvature) compared favorably with experimental results. However, results from thinner donor slabs (higher curvature) indicate a more sensitive behavior than the simulations predicted.

Preliminary test data using the MOS DRO with Si:In detector material

NASA Technical Reports Server (NTRS)

Fowler, A. M.; Britt, J. P.; Joyce, R. R.; Probst, R. G.; Gates, J. L.

1986-01-01

The initial testing performed on the Hughes Metal Oxide Semiconductor Direct Readout (MOS DRO) with a Si:In extrinsic infrared array is described. The testing to date was of a screening nature and the results are primarily qualitative rather than quantitative. At a later date the performance optimization phase will be initiated. An encouraging result is that this response is strongly dependent on the detector temperature, to the extent that thermal transients introduced during the chip readout will affect the performance. A responsivity of 1 A/W at 2.2 microns with a bias of 15 volts, which is well below what is optimum bias, was obtained.

Development and Test Evaluations for Ni-DOBDC Metal Organic Framework (MOF) Engineered Forms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Troy G. Garn; Mitchell Greenhalgh

2013-07-01

A joint effort to prepare engineered forms of a Ni-DOBDC metal organic framework (MOF) was completed with contributions from PNNL, SNL and the INL. Two independent methods were used at INL and SNL to prepare engineered form (EF) sorbents from Ni-DOBDC MOF powder developed and prepared at PNNL. Xe and Kr capacity test evaluations were performed at ambient temperature with the cryostat experimental setup at INL. The initial INL EF MOF test results indicated a Xe capacity of 1.6 mmol/kg sorbent and no Kr capacity. A large loss of surface area also occurred during minimal testing rendering the INL EFmore » MOF unusable. Four capacity tests were completed using the SNL EF MOF at ambient temperature and resulted in Xe capacities of 1.4, 4.2, 5.0 and 3.8 mmol/kg sorbent with no Kr capacity observed in any ambient temperature tests. Two additional capacity tests were performed at 240 K to further evaluate SNL EF MOF performance. Xe capacities of 50.7 and 49.3 mmol/kg of sorbent and Kr capacities of 0.77 and 0.69 mmol/kg of sorbent were obtained, respectively. Following the adsorption evaluations, the SNL EF MOF material had lost about 40 % of the initial mass and 40 % of the initial surface area. In general, the Xe capacity results at ambient temperature for the INL and SNL EF Ni-DOBDC MOF’s were lower than 9.8 mmol Xe/kg sorbent test results reported by INL in FY-12 using PNNL’s inital EF supplied material.« less

40 CFR Appendix 1 to Part 3 - Priority Reports

Code of Federal Regulations, 2013 CFR

2013-07-01

...). Hazardous Air Pollutants Compliance Report Reports containing results from performance test, opacity tests, and visible emissions tests. Progress reports; periodic and immediate startup, shutdown, and... Owners report emissions data from stationary sources 51.211. Report For Initial Performance Test Report...

40 CFR Appendix 1 to Part 3 - Priority Reports

Code of Federal Regulations, 2014 CFR

2014-07-01

...). Hazardous Air Pollutants Compliance Report Reports containing results from performance test, opacity tests, and visible emissions tests. Progress reports; periodic and immediate startup, shutdown, and... Owners report emissions data from stationary sources 51.211. Report For Initial Performance Test Report...

Comparing the results of an analytical model of the no-vent fill process with no-vent fill test results for a 4.96 cubic meters (175 cubic feet) tank

NASA Technical Reports Server (NTRS)

Taylor, William J.; Chato, David J.

1993-01-01

The NASA Lewis Research Center (NASA/LeRC) have been investigating a no-vent fill method for refilling cryogenic storage tanks in low gravity. Analytical modeling based on analyzing the heat transfer of a droplet has successfully represented the process in 0.034 m and 0.142 cubic m commercial dewars using liquid nitrogen and hydrogen. Recently a large tank (4.96 cubic m) was tested with hydrogen. This lightweight tank is representative of spacecraft construction. This paper presents efforts to model the large tank test data. The droplet heat transfer model is found to over predict the tank pressure level when compared to the large tank data. A new model based on equilibrium thermodynamics has been formulated. This new model is compared to the published large scale tank's test results as well as some additional test runs with the same equipment. The results are shown to match the test results within the measurement uncertainty of the test data except for the initial transient wall cooldown where it is conservative (i.e., overpredicts the initial pressure spike found in this time frame).

Initial CGE Model Results Summary Exogenous and Endogenous Variables Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, Brian Keith; Boero, Riccardo; Rivera, Michael Kelly

The following discussion presents initial results of tests of the most recent version of the National Infrastructure Simulation and Analysis Center Dynamic Computable General Equilibrium (CGE) model developed by Los Alamos National Laboratory (LANL). The intent of this is to test and assess the model’s behavioral properties. The test evaluated whether the predicted impacts are reasonable from a qualitative perspective. This issue is whether the predicted change, be it an increase or decrease in other model variables, is consistent with prior economic intuition and expectations about the predicted change. One of the purposes of this effort is to determine whethermore » model changes are needed in order to improve its behavior qualitatively and quantitatively.« less

Initial test results using the GEOS-3 engineering model altimeter

NASA Technical Reports Server (NTRS)

Hayne, G. S.; Clary, J. B.

1977-01-01

Data from a series of experimental tests run on the engineering model of the GEOS 3 radar altimeter using the Test and Measurement System (TAMS) designed for preflight testing of the radar altimeter are presented. These tests were conducted as a means of preparing and checking out a detailed test procedure to be used in running similar tests on the GEOS 3 protoflight model altimeter systems. The test procedures and results are also included.

Costs of Testing for Ocular Chlamydia trachomatis Infection Compared to Mass Drug Administration for Trachoma in The Gambia: Application of Results from the PRET Study

PubMed Central

Harding-Esch, Emma; Jofre-Bonet, Mireia; Dhanjal, Jaskiran K.; Burr, Sarah; Edwards, Tansy; Holland, Martin; Sillah, Ansumana; West, Sheila; Lietman, Tom; Keenan, Jeremy; Mabey, David; Bailey, Robin

2015-01-01

Background Mass drug administration (MDA) treatment of active trachoma with antibiotic is recommended to be initiated in any district where the prevalence of trachoma inflammation, follicular (TF) is ≥10% in children aged 1–9 years, and then to continue for at least three annual rounds before resurvey. In The Gambia the PRET study found that discontinuing MDA based on testing a sample of children for ocular Chlamydia trachomatis(Ct) infection after one MDA round had similar effects to continuing MDA for three rounds. Moreover, one round of MDA reduced disease below the 5% TF threshold. We compared the costs of examining a sample of children for TF, and of testing them for Ct, with those of MDA rounds. Methods The implementation unit in PRET The Gambia was a census enumeration area (EA) of 600–800 people. Personnel, fuel, equipment, consumables, data entry and supervision costs were collected for census and treatment of a sample of EAs and for the examination, sampling and testing for Ct infection of 100 individuals within them. Programme costs and resource savings from testing and treatment strategies were inferred for the 102 EAs in the study area, and compared. Results Census costs were $103.24 per EA plus initial costs of $108.79. MDA with donated azithromycin cost $227.23 per EA. The mean cost of examining and testing 100 children was $796.90 per EA, with Ct testing kits costing $4.80 per result. A strategy of testing each EA for infection is more expensive than two annual rounds of MDA unless the kit cost is less than $1.38 per result. However stopping or deciding not to initiate treatment in the study area based on testing a sample of EAs for Ct infection (or examining children in a sample of EAs) creates savings relative to further unnecessary treatments. Conclusion Resources may be saved by using tests for chlamydial infection or clinical examination to determine that initial or subsequent rounds of MDA for trachoma are unnecessary. PMID:25901349

Utility of the T-SPOT®.TB test's borderline category to increase test resolution for results around the cut-off point.

PubMed

Rego, Karen; Pereira, Kristen; MacDougall, James; Cruikshank, William

2018-01-01

Accurate identification of individuals with TB infection, is required to achieve the WHO's End TB Strategy goals. While there is general acceptance that the T-SPOT.TB test borderline category provides an opportunity to increase test resolution of results around the test cut-off point, this has not been investigated. 645,947 tests were analyzed to determine frequency of borderline results, effect of age and time between tests and associations between subjects' clinical risk factors and retest results. 645,947 tests produced 93.5% negatives, 4% positives, 0.6% invalids, and 1.8% borderlines. Within the borderline results, 5044 were repeated, with 59.2%, 20.0% and 20.2% resolving to negative, positive and borderline, respectively. Age of subject did not affect retest results; however, time between tests indicated that retest resolution occurred with greatest frequency after 90 days. TB risk factors were provided for 2640 subjects and 17% of low risk subjects with a high initial borderline resolved to negative while 27.6% of subjects with high risk and an initial low borderline resolved to positive, suggesting that these subjects could have been inappropriately classified if using a single cut-off point test with no borderline category. This study demonstrates the utility of the T-SPOT.TB test's borderline category to increase test resolution around the test cut-off point. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

RSRM TP-H1148 Main Grain Propellant Crack Initiation Evaluation

NASA Technical Reports Server (NTRS)

Earnest, Todd E.

2005-01-01

Pressurized TP-HI 148 propellant fracture toughness testing was performed to assess the potential for initiation of visually undetectable cracks in the RSRM forward segment transition region during motor ignition. Two separate test specimens were used in this evaluation. Testing was performed in cold-gas and hot-fire environments, and under both static and dynamic pressurization conditions. Analysis of test results demonstrates safety factors against initiation of visually undetectable cracks in excess of 8.0. The Reusable Solid Rocket Motor (RSRM) forward segment is cast with PBAN propellant (TP-HI 148) to form T an 1 1-point star configuration that transitions to a tapered center perforated bore (see Figure 1). The geometry of the transition region between the fin valleys and the bore causes a localized area of high strain during horizontal storage. Updated analyses using worst-case mechanical properties at 40 F and improved modeling techniques indicated a slight reduction in safety margins over previous predictions. Although there is no history of strain induced cracks or flaws in the transition region propellant, a proactive test effort was initiated to better understand the implications of the new analysis, primarily the resistance of TP-H1148 propellant to crack initiation' during RSRM ignition.

Eye-movement evidence of the time-course of attentional bias for threatening pictures in test-anxious students.

PubMed

Dong, Yunying; De Beuckelaer, Alain; Yu, Liang; Zhou, Renlai

2017-06-01

Protocols for measuring attentional bias to threat in test-anxiety, a special form of trait-anxiety, are rarely found in the literature. In our eye-tracking study, we introduced a new protocol, and studied the time-course of attention to test-related pictures with varying threat levels in 22 high test-anxious (HTA) and 22 low test-anxious (LTA) subjects. To determine whether attentional bias to test-related pictures is due to test-anxiety and not to state-anxiety, we also included a third group of 22 subjects with high state-anxiety but low test-anxiety (HSA). The subjects completed a free viewing task (FVT) in which high threat-neutral (HT-N) and low threat-neutral (LT-N) picture pairs were presented for 3 s. The results demonstrated that: (1) HTA subjects showed initial orienting to LT pictures, early attentional engagement with HT pictures later on and avoidance of HT pictures at the very end; (2) LTA subjects showed initial orienting to HT pictures and maintenance of attention on them later on; while (3) HSA subjects showed an initial orientation towards LT pictures and maintenance of attention on LT and HT pictures later on. These results suggest that, (high) test-anxiety is also prone to attentional bias towards test-related threat stimuli. Implications for future research are discussed.

Initial Back-to-Back Fission Chamber Testing in ATRC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benjamin Chase; Troy Unruh; Joy Rempe

2014-06-01

Development and testing of in-pile, real-time neutron sensors for use in Materials Test Reactor experiments is an ongoing project at Idaho National Laboratory. The Advanced Test Reactor National Scientific User Facility has sponsored a series of projects to evaluate neutron detector options in the Advanced Test Reactor Critical Facility (ATRC). Special hardware was designed and fabricated to enable testing of the detectors in the ATRC. Initial testing of Self-Powered Neutron Detectors and miniature fission chambers produced promising results. Follow-on testing required more experiment hardware to be developed. The follow-on testing used a Back-to-Back fission chamber with the intent to providemore » calibration data, and a means of measuring spectral indices. As indicated within this document, this is the first time in decades that BTB fission chambers have been used in INL facilities. Results from these fission chamber measurements provide a baseline reference for future measurements with Back-to-Back fission chambers.« less

Impact of SMS/GPRS Printers in Reducing Time to Early Infant Diagnosis Compared With Routine Result Reporting: A Systematic Review and Meta-Analysis

PubMed Central

Markby, Jessica; Boeke, Caroline; Penazzato, Martina; Urick, Brittany; Ghadrshenas, Anisa; Harris, Lindsay; Ford, Nathan; Peter, Trevor

2017-01-01

Background: Despite significant gains made toward improving access, early infant diagnosis (EID) testing programs suffer from long test turnaround times that result in substantial loss to follow-up and mortality associated with delays in antiretroviral therapy initiation. These delays in treatment initiation are particularly impactful because of significant HIV-related infant mortality observed by 2–3 months of age. Short message service (SMS) and general packet radio service (GPRS) printers allow test results to be transmitted immediately to health care facilities on completion of testing in the laboratory. Methods: We conducted a systematic review and meta-analysis to assess the benefit of using SMS/GPRS printers to increase the efficiency of EID test result delivery compared with traditional courier paper–based results delivery methods. Results: We identified 11 studies contributing data for over 16,000 patients from East and Southern Africa. The test turnaround time from specimen collection to result received at the health care facility with courier paper–based methods was 68.0 days (n = 6835), whereas the test turnaround time with SMS/GPRS printers was 51.1 days (n = 6711), resulting in a 2.5-week (25%) reduction in the turnaround time. Conclusions: Courier paper–based EID test result delivery methods are estimated to add 2.5 weeks to EID test turnaround times in low resource settings and increase the risk that infants receive test results during or after the early peak of infant mortality. SMS/GPRS result delivery to health care facility printers significantly reduced test turnaround time and may reduce this risk. SMS/GPRS printers should be considered for expedited delivery of EID and other centralized laboratory test results. PMID:28825941

The unintended consequences of cervical screening: distress in women undergoing cytologic surveillance.

PubMed

Sharp, Linda; Cotton, Seonaidh; Cruickshank, Margaret; Gray, Nicola M; Harrild, Kirsten; Smart, Louise; Walker, Leslie G; Little, Julian

2014-04-01

It is well known that receipt of an initial abnormal cervical cytology test can trigger considerable anxiety among women. Less is known about the impact of follow-up by repeat cytology tests. We quantified prevalence, and identified predictors, of distress after repeat cytologic testing in women with a single low-grade test. Within the framework of the TOMBOLA randomized controlled trial of alternative managements, 844 women aged 20 to 59 years with a single routine cytology test showing borderline nuclear abnormalities (BNA; broadly equivalent to atypical squamous cells of undetermined significance) were assigned to follow-up by repeat cytology in primary care (the first test was due 6 months after the initial BNA result). Women completed sociodemographic and psychosocial questionnaires at recruitment and the Impact of Event Scale (IES) 6 weeks after their first follow-up cytology test. Factors associated with significant psychologic distress (IES ≥ 9) were identified using logistic regression. The response rate was 74% (n = 621/844). Of all the respondents, 39% scored in the range for significant distress. Distress varied by follow-up cytology result: negative, 36%; BNA or mild dyskaryosis, 42%; other (including high grade and inadequate), 55%. After adjusting for the cytology result, risk of distress was significantly raised in women who had significant anxiety at recruitment, reported experiencing pain after the follow-up cytology, had children, or were dissatisfied with support they had received after their initial BNA test. Substantial proportions of women experience surveillance-related psychologic distress after a follow-up cytology test, even when the result is negative. This is an important, albeit unintended, consequence of cervical screening. Strategies to alleviate this distress merit attention.

Use of interferon-gamma release assays in a health care worker screening program: experience from a tertiary care centre in the United States.

PubMed

Joshi, Manish; Monson, Thomas P; Woods, Gail L

2012-01-01

Interferon-gamma release assays including the QuantiFERON-TB Gold In-Tube test (QFT-GIT [Cellestis Ltd, Australia]) may be used in place of the tuberculin skin test (TST) in surveillance programs for Mycobacterium tuberculosis infection control. However, data on performance and practicality of the QFT-GIT in such programs for health care workers (HCWs) are limited. To assess the performance, practicality and reversion rate of the QFT-GIT among HCWs at a tertiary health care institution in the United States. Retrospective chart review of HCWs at Central Arkansas Veterans Healthcare System (Arkansas, USA) who underwent QFT-GIT testing as a part of their employee screening between November 1, 2008 and October 31, 2009. QFT-GIT was used to screen 3290 HCWs. The initial QFT-GIT was interpreted as positive for 129 (3.9%) HCWs, negative for 3155 (95.9%) and indeterminate for six (0.2%). Testing with QFT-GIT was repeated in 45 HCWs who had positive results on the initial test. The QFT-GIT reverted to negative in 18 (40.0%) HCWs, all of whom had negative TST status and initial interferon-gamma values of 0.35 IU⁄mL to 2.0 IU⁄mL. The QFT-GIT test is feasible in large health care setting as an alternative to TST for M tuberculosis infection screening in HCWs but is not free from challenges. The major concerns are the high number of positive test results and high reversion rates on repeat testing, illustrating poor short-term reproducibility of positive QFT-GIT test results. These results suggest adopting a borderline zone between interferon-gamma values of 0.35 IU⁄mL to 2.0 IU⁄mL, and cautious clinical interpretation of values in this range.

The effects of work engagement and self-efficacy on personal initiative and performance.

PubMed

Lisbona, Ana; Palaci, Francisco; Salanova, Marisa; Frese, Michael

2018-02-01

Two popular concepts, work engagement and personal initiative, are different but related constructs. This study is based on and extends the Frese and Fay (2001) model of personal initiative (PI) by including work engagement (WE) and self-efficacy as antecedents of PI, and performance as a consequence. Two studies (study 1, with a cross-sectional design using N = 396 participants from 22 organizations, and study 2, with a longitudinal design conducted in two waves with N = 118 participants from 15 organizations) test the hypotheses. Structural equation modeling and the PROCESS SPSS Macro were used to test the hypothesized mediating role of personal initiative in work engagement and performance, and the results show the indirect effect of WE on performance through PI. The results of these two studies confirmed our hypotheses: WE and self-efficacy lead to higher PI, which, in turn, leads to higher performance. In addition to considering WE as an antecedent of PI, the results lead to considering PI as an antecedent of performance.

Attitude algorithm and initial alignment method for SINS applied in short-range aircraft

NASA Astrophysics Data System (ADS)

Zhang, Rong-Hui; He, Zhao-Cheng; You, Feng; Chen, Bo

2017-07-01

This paper presents an attitude solution algorithm based on the Micro-Electro-Mechanical System and quaternion method. We completed the numerical calculation and engineering practice by adopting fourth-order Runge-Kutta algorithm in the digital signal processor. The state space mathematical model of initial alignment in static base was established, and the initial alignment method based on Kalman filter was proposed. Based on the hardware in the loop simulation platform, the short-range flight simulation test and the actual flight test were carried out. The results show that the error of pitch, yaw and roll angle is fast convergent, and the fitting rate between flight simulation and flight test is more than 85%.

Promoting clinical and laboratory interaction by harmonization.

PubMed

Plebani, Mario; Panteghini, Mauro

2014-05-15

The lack of interchangeable results in current practice among clinical laboratories has underpinned greater attention to standardization and harmonization projects. Although the focus was mainly on the standardization and harmonization of measurement procedures and their results, the scope of harmonization goes beyond method and analytical results: it includes all other aspects of laboratory testing, including terminology and units, report formats, reference limits and decision thresholds, as well as test profiles and criteria for the interpretation of results. In particular, as evidence collected in last decades demonstrates that pre-pre- and post-post-analytical steps are more vulnerable to errors, harmonization initiatives should be performed to improve procedures and processes at the laboratory-clinical interface. Managing upstream demand, down-stream interpretation of laboratory results, and subsequent appropriate action through close relationships between laboratorians and clinicians remains a crucial issue of the laboratory testing process. Therefore, initiatives to improve test demand management from one hand and to harmonize procedures to improve physicians' acknowledgment of laboratory data and their interpretation from the other hand are needed in order to assure quality and safety in the total testing process. © 2013.

Ground testing on the nonvented fill method of orbital propellant transfer: Results of initial test series

NASA Technical Reports Server (NTRS)

Chato, David J.

1991-01-01

The results are presented of a series of no-vent fill experiments conducted on a 175 cu ft flightweight hydrogen tank. The experiments consisted of the nonvented fill of the tankage with liquid hydrogen using two different inlet systems (top spray, and bottom spray) at different tank initial conditions and inflow rates. Nine tests were completed of which six filled in excess of 94 percent. The experiments demonstrated a consistent and repeatable ability to fill the tank in excess of 94 percent using the nonvented fill technique. Ninety-four percent was established as the high level cutoff due to requirements for some tank ullage to prevent rapid tank pressure rise which occurs in a tank filled entirely with liquid. The best fill was terminated at 94 percent full with a tank internal pressure less than 26 psia. Although the baseline initial tank wall temperature criteria was that all portions of the tank wall be less than 40 R, fills were achieved with initial wall temperatures as high as 227 R.

Investigation of the Semicoa SCF9550 and the International Rectifier IRHM57260SE for Single-Event Gate Rapture and Single-Event Burnout : NASA Electronic Parts and Packaging (NEPP) Program Office of Safety and Mission Assurance

NASA Technical Reports Server (NTRS)

Scheick, Leif

2011-01-01

Single-event-effect test results for hi-rel total-dose-hardened power MOSFETs are presented in this report. TheSCF9550 from Semicoa and the IRHM57260SE from International Rectifier were tested to NASA test condition/standards and requirements.The IRHM57260SE performed much better when compared to previous testing. These initial results confirm that parts from the Temecula line are marginally comparable to the El Segundo line. The SCF9550 from Semicoa was also tested and represents the initial parts offering from this vendor. Both parts experienced single-event gate rupture (SEGR) and single-event burnout (SEB). All of the SEGR was from gate to drain.

Flight service evaluation of composite helicopter components

NASA Technical Reports Server (NTRS)

Rich, M. J.; Lowry, D. W.

1983-01-01

This first interim report presents the technical background for including environmental effects in the design of helicopter composite structures, and test results after approximately two year field exposure of components and panels. Composite structural components were removed from Sikorsky S-76 helicopters commercially operated in the Gulf Coast region of Louisiana. Fatigue tests were conducted for a graphite/epoxy tail rotor spar and static test for a graphite/epoxy and Kevlar/epoxy stabilizer. Graphite/epoxy and Kevlar/epoxy panels are being exposed to the outdoor environment in Stratford, Connecticut and West Palm Beach, Florida. For this reporting period the two year panels were returned, moisture measurements taken, and strength tests conducted. Results are compared with initial type certificate strengths for components and with initial laboratory coupon tests for the exposed panels. Comparisons are also presented with predicted and measured moisture contents.

Flight service evaluation of composite helicopter components

NASA Technical Reports Server (NTRS)

Rich, M. J.; Lowry, D. W.

1982-01-01

This first interim report presents the technical background for including environmental effects in the design of helicopter composite structures, and test results after approximately two year field exposure of components and panels. Composite structural components were removed from Sikorsky S-76 helicopters commercially operated in the Gulf Coast region of Louisiana. Fatigue tests were conducted for a graphite/epoxy tail rotor spar and static test for a graphite/epoxy and Kevlar/epoxy stabilizer. Graphite/epoxy and Kevlar/epoxy panels are being exposed to the outdoor environment in Stratford, Connecticut and West Palm Beach, Florida. For this reporting period the two year panels were returned, moisture measurements taken, and strength tests conducted. Results are compared with initial type certificate strengths for components and with initial laboratory coupon tests for the exposed panels. Comparisons are also presented with predicted and measured moisture contents.

NASA Standard Initiator Susceptibility to UHF and S-Band Radio Frequency Power and Lightning Strikes

NASA Technical Reports Server (NTRS)

Burnham, Karen; Scully, Robert; Norgard, John

2013-01-01

The NASA Standard Initiator (NSI) is an important piece of pyrotechnic equipment used in many space applications. This presentation will outline the results of a series of tests done at UHF and S-Band frequencies to determine NSI susceptibility to Radio Frequency (RF) power. The results show significant susceptibility to pulsed RF power in the S-Band region. Additional testing with lightning pulses injected into the firing line harness, modelling the indirect effects of a lightning strike to a spacecraft, showed no vulnerability

NASA Standard Initiator Susceptibility to UHF and S-Band Radio Frequency Power and Lightning Strikes

NASA Technical Reports Server (NTRS)

Burnham, Karen; Scully, Robert C.; Norgard, John D.

2013-01-01

The NASA Standard Initiator (NSI) is an important piece of pyrotechnic equipment used in many space applications. This paper outlines the results of a series of tests done at UHF and S-Band frequencies to determine NSI susceptibility to Radio Frequency (RF) power. The results show significant susceptibility to pulsed RF power in the S-Band region. Additional testing with lightning pulses injected into the firing line harness, modelling the indirect effects of a lightning strike to a spacecraft, showed no vulnerability.

Pathways to multidrug-resistant tuberculosis diagnosis and treatment initiation: a qualitative comparison of patients' experiences in the era of rapid molecular diagnostic tests.

PubMed

Naidoo, Pren; van Niekerk, Margaret; du Toit, Elizabeth; Beyers, Nulda; Leon, Natalie

2015-10-28

Although new molecular diagnostic tests such as GenoType MTBDRplus and Xpert® MTB/RIF have reduced multidrug-resistant tuberculosis (MDR-TB) treatment initiation times, patients' experiences of diagnosis and treatment initiation are not known. This study aimed to explore and compare MDR-TB patients' experiences of their diagnostic and treatment initiation pathway in GenoType MTBDRplus and Xpert® MTB/RIF-based diagnostic algorithms. The study was undertaken in Cape Town, South Africa where primary health-care services provided free TB diagnosis and treatment. A smear, culture and GenoType MTBDRplus diagnostic algorithm was used in 2010, with Xpert® MTB/RIF phased in from 2011-2013. Participants diagnosed in each algorithm at four facilities were purposively sampled, stratifying by age, gender and MDR-TB risk profiles. We conducted in-depth qualitative interviews using a semi-structured interview guide. Through constant comparative analysis we induced common and divergent themes related to symptom recognition, health-care access, testing for MDR-TB and treatment initiation within and between groups. Data were triangulated with clinical information and health visit data from a structured questionnaire. We identified both enablers and barriers to early MDR-TB diagnosis and treatment. Half the patients had previously been treated for TB; most recognised recurring symptoms and reported early health-seeking. Those who attributed symptoms to other causes delayed health-seeking. Perceptions of poor public sector services were prevalent and may have contributed both to deferred health-seeking and to patient's use of the private sector, contributing to delays. However, once on treatment, most patients expressed satisfaction with public sector care. Two patients in the Xpert® MTB/RIF-based algorithm exemplified its potential to reduce delays, commencing MDR-TB treatment within a week of their first health contact. However, most patients in both algorithms experienced substantial delays. Avoidable health system delays resulted from providers not testing for TB at initial health contact, non-adherence to testing algorithms, results not being available and failure to promptly recall patients with positive results. Whilst the introduction of rapid tests such as Xpert® MTB/RIF can expedite MDR-TB diagnosis and treatment initiation, the full benefits are unlikely to be realised without reducing delays in health-seeking and addressing the structural barriers present in the health-care system.

A small punch test technique for characterizing the elastic modulus and fracture behavior of PMMA bone cement used in total joint replacement.

PubMed

Giddings, V L; Kurtz, S M; Jewett, C W; Foulds, J R; Edidin, A A

2001-07-01

Polymethylmethacrylate (PMMA) bone cement is used in total joint replacements to anchor implants to the underlying bone. Establishing and maintaining the integrity of bone cement is thus of critical importance to the long-term outcome of joint replacement surgery. The goal of the present study was to evaluate the suitability of a novel testing technique, the small punch or miniaturized disk bend test, to characterize the elastic modulus and fracture behavior of PMMA. We investigated the hypothesis that the crack initiation behavior of PMMA during the small punch test was sensitive to the test temperature. Miniature disk-shaped specimens, 0.5 mm thick and 6.4 mm in diameter, were prepared from PMMA and Simplex-P bone cement according to manufacturers' instructions. Testing was conducted at ambient and body temperatures, and the effect of test temperature on the elastic modulus and fracture behavior was statistically evaluated using analysis of variance. For both PMMA materials, the test temperature had a significant effect on elastic modulus and crack initiation behavior. At body temperature, the specimens exhibited "ductile" crack initiation, whereas at room temperature "brittle" crack initiation was observed. The small punch test was found to be a sensitive and repeatable test method for evaluating the mechanical behavior of PMMA. In light of the results of this study, future small punch testing should be conducted at body temperature.

Electronic delay ignition module for single bridgewire Apollo standard initiator

NASA Technical Reports Server (NTRS)

Ward, R. D.

1975-01-01

An engineering model and a qualification model of the EDIM were constructed and tested to Scout flight qualification criteria. The qualification model incorporated design improvements resulting from the engineering model tests. Compatibility with single bridgewire Apollo standard initiator (SBASI) was proven by test firing forty-five (45) SBASI's with worst case voltage and temperature conditions. The EDIM was successfully qualified for Scout flight application with no failures during testing of the qualification unit. Included is a method of implementing the EDIM into Scout vehicle hardware and the ground support equipment necessary to check out the system.

Double torsion fracture mechanics testing of shales under chemically reactive conditions

NASA Astrophysics Data System (ADS)

Chen, X.; Callahan, O. A.; Holder, J. T.; Olson, J. E.; Eichhubl, P.

2015-12-01

Fracture properties of shales is vital for applications such as shale and tight gas development, and seal performance of carbon storage reservoirs. We analyze the fracture behavior from samples of Marcellus, Woodford, and Mancos shales using double-torsion (DT) load relaxation fracture tests. The DT test allows the determination of mode-I fracture toughness (KIC), subcritical crack growth index (SCI), and the stress-intensity factor vs crack velocity (K-V) curves. Samples are tested at ambient air and aqueous conditions with variable ionic concentrations of NaCl and CaCl2, and temperatures up to 70 to determine the effects of chemical/environmental conditions on fracture. Under ambient air condition, KIC determined from DT tests is 1.51±0.32, 0.85±0.25, 1.08±0.17 MPam1/2 for Marcellus, Woodford, and Mancos shales, respectively. Tests under water showed considerable change of KIC compared to ambient condition, with 10.6% increase for Marcellus, 36.5% decrease for Woodford, and 6.7% decrease for Mancos shales. SCI under ambient air condition is between 56 and 80 for the shales tested. The presence of water results in a significant reduction of the SCI from 70% to 85% compared to air condition. Tests under chemically reactive solutions are currently being performed with temperature control. K-V curves under ambient air conditions are linear with stable SCI throughout the load-relaxation period. However, tests conducted under water result in an initial cracking period with SCI values comparable to ambient air tests, which then gradually transition into stable but significantly lower SCI values of 10-20. The non-linear K-V curves reveal that crack propagation in shales is initially limited by the transport of chemical agents due to their low permeability. Only after the initial cracking do interactions at the crack tip lead to cracking controlled by faster stress corrosion reactions. The decrease of SCI in water indicates higher crack propagation velocity due to faster stress corrosion rate in water than in ambient air. The experimental results are applicable for the prediction of fracture initiation based on KIC, modeling fracture pattern based on SCI, and the estimation of dynamic fracture propagation such as crack growth velocity and crack re-initiation.

CALiPER Report 24: OLED Luminaires

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, N. J.; Leon, F. A.; Davis, J. L.

2017-08-01

This report documents an initial investigation of OLED luminaires and summarizes the key features of those products. In addition to photometric testing of four commercial products in independent laboratories, PNNL examined many of the products through teardown testing (disassemblies to identify parts and functionality) in PNNL laboratories. Results of these tests as well as results of stress testing of several OLED luminaires at RTI International have been included.

Implications of Dynamic Pressure Transducer Mounting Variations on Measurements in Pyrotechnic Test Apparatus

NASA Technical Reports Server (NTRS)

Dibbern, Andreas; Crisafulli, Jeffrey; Hagopia, Michael; McDougle, Stephen H.; Saulsberry, Regor L.

2009-01-01

Accurate dynamic pressure measurements are often difficult to make within small pyrotechnic devices, and transducer mounting difficulties can cause data anomalies that lead to erroneous conclusions. Delayed initial pressure response followed by data ringing has been observed when using miniaturized pressure transducer mounting adapters required to interface transducers to small test chambers. This delayed pressure response and ringing, combined with a high data acquisition rate, has complicated data analysis. This paper compares the output signal characteristics from different pressure transducer mounting options, where the passage distance from the transducer face to the pyrotechnic chamber is varied in length and diameter. By analyzing the data and understating the associated system dynamics, a more realistic understanding of the actual dynamic pressure variations is achieved. Three pressure transducer mounting configurations (elongated, standard, and face/flush mount) were simultaneously tested using NASA standard initiators in closed volume pressure bombs. This paper also presents results of these pressure transducer mounting configurations as a result of a larger NASA Engineering and Safety Center pyrovalve test project. Results from these tests indicate the improved performance of using face/flush mounted pressure transducers in this application. This type of mounting improved initial pressure measurement response time by approximately 19 s over standard adapter mounting, eliminating most of the lag time; provided a near step-function type initial pressure increase; and greatly reduced data ringing in high data acquisition rate systems. The paper goes on to discuss other issues associated with the firing and instrumentation that are important for the tester to understand.

Cold Helium Pressurization for Liquid Oxygen / Liquid Methane Propulsion Systems: Fully-Integrated Initial Hot-Fire Test Results

NASA Technical Reports Server (NTRS)

Morehead, R. L.; Atwell, M. J.; Melcher, J. C.; Hurlbert, E. A.

2016-01-01

A prototype cold helium active pressurization system was incorporated into an existing liquid oxygen (LOX) / liquid methane (LCH4) prototype planetary lander and hot-fire tested to collect vehicle-level performance data. Results from this hot-fire test series were used to validate integrated models of the vehicle helium and propulsion systems and demonstrate system effectiveness for a throttling lander. Pressurization systems vary greatly in complexity and efficiency between vehicles, so a pressurization performance metric was also developed as a means to compare different active pressurization schemes. This implementation of an active repress system is an initial sizing draft. Refined implementations will be tested in the future, improving the general knowledge base for a cryogenic lander-based cold helium system.

Normal sensory and range of motion (ROM) responses during Thoracic Slump Test (ST) in asymptomatic subjects.

PubMed

Joshi, Ketaki C; Eapen, Charu; Kumar, Senthil P

2013-02-01

The purpose of the study was to determine the normal sensory and range of motion (ROM) responses during the movement components of Thoracic Slump Test (Thoracic ST) in asymptomatic subjects. Sixty asymptomatic subjects were included in the study. Thoracic ST was performed in two sequences, proximal initiation, which was proximal to distal and distal initiation, which was distal to proximal. Subjects were randomized into four groups depending on the order of sequences and sides. Outcome measures of sensory responses (intensity, type, and location) and ROM responses were recorded after each sequence. Friedman's test was done to compare between sensory responses of the subjects. Between-component comparison for prevalence of sensory responses within each sequence was done using Kruskal-Wallis test and Wilcoxonsigned ranks test was used for between-component comparisons of intensity of symptoms within each sequence of testing. Independent t test was used to assess the ROM responses. Results show the prevalence of sensory responses, its nature, area and intensity. These sensory and ROM responses may be considered as normal response of Thoracic ST. The intensity of the symptoms of proximal initiation sequence (1.09±1.35 cm) was significant (P<0.05) when compared to distal initiation sequence (0.08±1.26 cm). The change in the ROM was significant (P<0.05) for distal initiation (7.55±4.51 degrees) when compared to proximal initiation (4.96±3.76 degrees). These normal responses may be used as a reference when using the Thoracic ST as an assessment technique.

Normal sensory and range of motion (ROM) responses during Thoracic Slump Test (ST) in asymptomatic subjects

PubMed Central

Joshi, Ketaki C; Eapen, Charu; Kumar, Senthil P

2013-01-01

The purpose of the study was to determine the normal sensory and range of motion (ROM) responses during the movement components of Thoracic Slump Test (Thoracic ST) in asymptomatic subjects. Sixty asymptomatic subjects were included in the study. Thoracic ST was performed in two sequences, proximal initiation, which was proximal to distal and distal initiation, which was distal to proximal. Subjects were randomized into four groups depending on the order of sequences and sides. Outcome measures of sensory responses (intensity, type, and location) and ROM responses were recorded after each sequence. Friedman’s test was done to compare between sensory responses of the subjects. Between-component comparison for prevalence of sensory responses within each sequence was done using Kruskal–Wallis test and Wilcoxonsigned ranks test was used for between-component comparisons of intensity of symptoms within each sequence of testing. Independent t test was used to assess the ROM responses. Results show the prevalence of sensory responses, its nature, area and intensity. These sensory and ROM responses may be considered as normal response of Thoracic ST. The intensity of the symptoms of proximal initiation sequence (1.09±1.35 cm) was significant (P<0.05) when compared to distal initiation sequence (0.08±1.26 cm). The change in the ROM was significant (P<0.05) for distal initiation (7.55±4.51 degrees) when compared to proximal initiation (4.96±3.76 degrees). These normal responses may be used as a reference when using the Thoracic ST as an assessment technique. PMID:24421610

Creep fatigue life prediction for engine hot section materials (isotropic)

NASA Technical Reports Server (NTRS)

Moreno, V.

1983-01-01

The Hot Section Technology (HOST) program, creep fatigue life prediction for engine hot section materials (isotropic), is reviewed. The program is aimed at improving the high temperature crack initiation life prediction technology for gas turbine hot section components. Significant results include: (1) cast B1900 and wrought IN 718 selected as the base and alternative materials respectively; (2) fatigue test specimens indicated that measurable surface cracks appear early in the specimen lives, i.e., 15% of total life at 871 C and 50% of life at 538 c; (3) observed crack initiation sites are all surface initiated and are associated with either grain boundary carbides or local porosity, transgrannular cracking is observed at the initiation site for all conditions tested; and (4) an initial evaluation of two life prediction models, representative of macroscopic (Coffin-Mason) and more microscopic (damage rate) approaches, was conducted using limited data generated at 871 C and 538 C. It is found that the microscopic approach provides a more accurate regression of the data used to determine crack initiation model constants, but overpredicts the effect of strain rate on crack initiation life for the conditions tested.

Does the delivery of diagnostic news affect the likelihood of whether or not patients ask questions about the results? A conversation analytical study.

PubMed

Murtagh, Ged M; Thomas, Anne L; Furber, Lynn

2018-05-03

Asymmetries in knowledge and competence in the medical encounter often mean that doctor-patient communication can be compromised. This study explores this issue and examines whether the likelihood of patient question asking is increased following the delivery of diagnostic test results. It also examines whether that likelihood is related to the way in which the test results are delivered. To examine when and how patients initiate questions following diagnostic news announcements. We audio-recorded oncology consultations (n = 47) consisting of both first consultations and follow-up consultations with patients with different types of cancer, at a leading UK teaching hospital. From the primary sample, we identified 30 consultations based on a basic count of the frequency of patient questions and their positioning in relation to diagnostic announcements. This subset of 30 consultations consisted of a mix of first and follow-up consultations. Our data demonstrate how the design and delivery of diagnostic news announcements can either discourage or provide the opportunity for a patient-initiated question in the next turn of talk. We identified two types of announcement. Q+ generally provided for a patient-initiated question as a relevant next turn following the news announcement, whereas Q- did not. Q+ was sometimes followed up with the explanation of test results, which appeared to encourage further patient questions. The design and delivery of diagnostic news announcements can make a patient-initiated question more or less appropriate, in the next turn of talk. In addition, showing and explaining test results can encourage further opportunities for patients' questions. © 2018 The Authors. Health Expectations published by John Wiley & Sons Ltd.

Progressing from initially ambiguous functional analyses: three case examples.

PubMed

Tiger, Jeffrey H; Fisher, Wayne W; Toussaint, Karen A; Kodak, Tiffany

2009-01-01

Most often functional analyses are initiated using a standard set of test conditions, similar to those described by Iwata, Dorsey, Slifer, Bauman, and Richman [Iwata, B. A., Dorsey, M. F., Slifer, K. J., Bauman, K. E., & Richman, G. S. (1994). Toward a functional analysis of self-injury. Journal of Applied Behavior Analysis, 27, 197-209 (Reprinted from Analysis and Intervention in Developmental Disabilities, 2, 3-20, 1982)]. These test conditions involve the careful manipulation of motivating operations, discriminative stimuli, and reinforcement contingencies to determine the events related to the occurrence and maintenance of problem behavior. Some individuals display problem behavior that is occasioned and reinforced by idiosyncratic or otherwise unique combinations of environmental antecedents and consequences of behavior, which are unlikely to be detected using these standard assessment conditions. For these individuals, modifications to the standard test conditions or the inclusion of novel test conditions may result in clearer assessment outcomes. The current study provides three case examples of individuals whose functional analyses were initially undifferentiated; however, modifications to the standard conditions resulted in the identification of behavioral functions and the implementation of effective function-based treatments.

Automotive Stirling Engine Development Program

NASA Technical Reports Server (NTRS)

Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Antonelli, M. (Editor)

1982-01-01

Activities performed on Mod I engine testing and test results; the manufacture, assembly, and test of a Mod I engine in the United States; design initiation of the Mod I-A engine system; transient performance testing; Stirling reference engine manufacturing and reduced size studies; components and subsystems; and the study and test of low cost alloys are summarized.

49 CFR 40.96 - What criteria do laboratories use to establish that a specimen is invalid?

Code of Federal Regulations, 2012 CFR

2012-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the invalid test result criteria for the initial and confirmation testing as... whether sending the specimen to another HHS certified laboratory for testing would be useful in being able...

49 CFR 40.96 - What criteria do laboratories use to establish that a specimen is invalid?

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the invalid test result criteria for the initial and confirmation testing as... whether sending the specimen to another HHS certified laboratory for testing would be useful in being able...

49 CFR 40.96 - What criteria do laboratories use to establish that a specimen is invalid?

Code of Federal Regulations, 2013 CFR

2013-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the invalid test result criteria for the initial and confirmation testing as... whether sending the specimen to another HHS certified laboratory for testing would be useful in being able...

49 CFR 40.96 - What criteria do laboratories use to establish that a specimen is invalid?

Code of Federal Regulations, 2011 CFR

2011-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the invalid test result criteria for the initial and confirmation testing as... whether sending the specimen to another HHS certified laboratory for testing would be useful in being able...

49 CFR 40.96 - What criteria do laboratories use to establish that a specimen is invalid?

Code of Federal Regulations, 2014 CFR

2014-10-01

... Transportation PROCEDURES FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing... laboratory, you must use the invalid test result criteria for the initial and confirmation testing as... whether sending the specimen to another HHS certified laboratory for testing would be useful in being able...

Evaluation of Fracture Initiation in the Mannesmann Piercing Process

NASA Astrophysics Data System (ADS)

Fanini, S.; Ghiotti, A.; Bruschi, S.

2007-04-01

One of the challenging objectives in studying the Mannesmann piercing process is to predict the fracture initiation, known as "Mannesmann effect", in order to design and optimize the working parameters of the piercing process. The objective of the paper is to investigate the workability of a tube steel tested in the same conditions of the Mannesman piercing process. The stress and strain states as well as temperature fields arising during the process are identified through numerical simulations. The hot tensile test is chosen for fundamental studies on fracture initiation, as a tensile state of stress in the centre of the billet in the first stages of the piercing process before the plug arrival seems to be one of the main causes of the crack initiation. The material constants of energy-based models implemented in FEM codes are calculated and numerical results are compared with non-plug piercing tests carried out on the industrial plant.

Out-of-core Evaluations of Uranium Nitride-fueled Converters

NASA Technical Reports Server (NTRS)

Shimada, K.

1972-01-01

Two uranium nitride fueled converters were tested parametrically for their initial characterization and are currently being life-tested out of core. Test method being employed for the parametric and the diagnostic measurements during the life tests, and test results are presented. One converter with a rhenium emitter had an initial output power density of 6.9 W/ sq cm at the black body emitter temperature of 1900 K. The power density remained unchanged for the first 1000 hr of life test but degraded nearly 50% percent during the following 1000 hr. Electrode work function measurements indicated that the uranium fuel was diffusing out of the emitter clad of 0.635 mm. The other converter with a tungsten emitter had an initial output power density of 2.2 W/ sq cm at 1900 K with a power density of 3.9 W/sq cm at 4300 h. The power density suddenly degraded within 20 hr to practically zero output at 4735 hr.

ROC and Loss Function Analysis in Sequential Testing

ERIC Educational Resources Information Center

Muijtjens, Arno M. M.; Van Luijk, Scheltus J.; Van Der Vleuten, Cees P. M.

2006-01-01

Sequential testing is applied to reduce costs in SP-based tests (OSCEs). Initially, all candidates take a screening test consisting of a part of the OSCE. Candidates who fail the screen sit the complete test, whereas those who pass the screen are qualified as a pass of the complete test. The procedure may result in a reduction of testing…

A cluster randomized trial of provider-initiated (Opt-out) HIV counseling and testing of tuberculosis patients in South Africa

PubMed Central

Pope, Diana S.; DeLuca, Andrea N.; Kali, Paula; Hausler, Harry; Sheard, Carol; Hoosain, Ebrahim; Chaudhary, Mohammed A.; Celentano, David D.; Chaisson, Richard E.

2008-01-01

Objective To determine whether implementation of provider-initiated HIV counseling would increase the proportion of tuberculosis patients that received HIV counseling and testing. Design Cluster-randomized trial with clinic as unit of randomization Setting Twenty, medium-sized primary care TB clinics in the Nelson Mandela Metropolitan Municipality, Port Elizabeth, Eastern Cape Province, South Africa Subjects A total of 754 adults (≥ 18 years) newly registered as tuberculosis patients the twenty study clinics Intervention Implementation of provider-initiated HIV counseling and testing. Main outcome measures Percentage of TB patients HIV counseled and tested. Secondary Percentage of patients HIV test positive and percentage of those that received cotrimoxazole and who were referred for HIV care. Results A total of 754 adults newly registered as tuberculosis patients were enrolled. In clinics randomly assigned to implement provider-initiated HIV counseling and testing, 20.7% (73/352) patients were counseled versus 7.7% (31/402) in the control clinics (p = 0.011), and 20.2 % (n = 71) versus 6.5% (n = 26) underwent HIV testing (p = 0.009). Of those patients counseled, 97% in the intervention clinics accepted testing versus 79% in control clinics (p =0.12). The proportion of patients identified as HIV-infected in intervention clinics was 8.5% versus 2.5% in control clinics (p=0.044). Fewer than 40% of patients with a positive HIV test were prescribed cotrimoxazole or referred for HIV care in either study arm. Conclusions Provider-initiated HIV counseling significantly increased the proportion of adult TB patients that received HIV counseling and testing, but the magnitude of the effect was small. Additional interventions to optimize HIV testing for TB patients urgently need to be evaluated. PMID:18520677

DOE Office of Scientific and Technical Information (OSTI.GOV)

McAdams, Brian J.; Pearson, Raymond A.

With the continuing trend of decreasing feature sizes in flip-chip assemblies, the reliability tolerance to interfacial flaws is also decreasing. Small-scale disbonds will become more of a concern, pointing to the need for a better understanding of the initiation stage of interfacial delamination. With most accepted adhesion metric methodologies tailored to predict failure under the prior existence of a disbond, the study of the initiation phenomenon is open to development and standardization of new testing procedures. Traditional fracture mechanics approaches are not suitable, as the mathematics assume failure to originate at a disbond or crack tip. Disbond initiation is believedmore » to first occur at free edges and corners, which act as high stress concentration sites and exhibit singular stresses similar to a crack tip, though less severe in intensity. As such, a 'fracture mechanics-like' approach may be employed which defines a material parameter--a critical stress intensity factor (K{sub c})--that can be used to predict when initiation of a disbond at an interface will occur. The factors affecting the adhesion of underfill/polyimide interfaces relevant to flip-chip assemblies were investigated in this study. The study consisted of two distinct parts: a comparison of the initiation and propagation phenomena and a comparison of the relationship between sub-critical and critical initiation of interfacial failure. The initiation of underfill interfacial failure was studied by characterizing failure at a free-edge with a critical stress intensity factor. In comparison with the interfacial fracture toughness testing, it was shown that a good correlation exists between the initiation and propagation of interfacial failures. Such a correlation justifies the continuing use of fracture mechanics to predict the reliability of flip-chip packages. The second aspect of the research involved fatigue testing of tensile butt joint specimens to determine lifetimes at sub-critical load levels. The results display an interfacial strength ranking similar to that observed during monotonic testing. The fatigue results indicate that monotonic fracture mechanics testing may be an adequate screening tool to help predict cyclic underfill failure; however lifetime data is required to predict reliability.« less

The Predictive Validity of the Metropolitan Readiness Tests, 1976 Edition.

ERIC Educational Resources Information Center

Nagle, Richard J.

1979-01-01

A sample of 176 first-grade children was tested on the Metropolitan Readiness Tests, 1976 Edition (MRT), during the initial month of school and was retested eight months later on the Stanford Achievement Test. Results demonstrated substantial validity of the MRT for predicting first-grade achievement. (Author/CTM)

Operational evaluation of initial data link air traffic control services, Vol. 1

DOT National Transportation Integrated Search

1990-02-01

This report details the results of an operational evaluation of Initial Data Link Air Traffic Control (ATC) Services. The Operational Evaluation was conducted at the Federal Aviation Administration (FAA) Technical Center utilizing the Data Link test ...

Engineering sciences area and module performance and failure analysis area

NASA Technical Reports Server (NTRS)

Ross, R. G., Jr.; Runkle, L. D.

1982-01-01

Photovoltaic-array/power-conditioner interface studies are updated. An experiment conducted to evaluate different operating-point strategies, such as constant voltage and pilot cells, and to determine array energy losses when the array is operated off the maximum power points is described. Initial results over a test period of three and a half weeks showed a 2% energy loss when the array is operated at a fixed voltage. Degraded-array studies conducted at NE RES that used a range of simulated common types of degraded I-V curves are reviewed. The instrumentation installed at the JPL field-test site to obtain the irradiance data was described. Experiments using an optical filter to adjust the spectral irradiance of the large-area pulsed solar simulator (LAPSS) to AM1.5 are described. Residential-array research activity is reviewed. Voltage isolation test results are described. Experiments performed on one type of module to determine the relationship between leakage current and temperature are reviewed. An encapsulated-cell testing approach is explained. The test program, data reduction methods, and initial results of long-duration module testing are described.

Comparison of the inertial properties and forces required to initiate movement for three gait trainers.

PubMed

Paleg, Ginny; Huang, Morris; Vasquez Gabela, Stephanie C; Sprigle, Stephen; Livingstone, Roslyn

2016-01-01

The purpose of this study was to evaluate the inertial properties and forces required to initiate movement on two different surfaces in a sample of three commonly prescribed gait trainers. Tests were conducted in a laboratory setting to compare the Prime Engineering KidWalk, Rifton Pacer, and Snug Seat Mustang with and without a weighted anthropometric test dummy configured to the weight and proportions of a 4-year-old child. The Pacer was the lightest and the KidWalk the heaviest while footprints of the three gait trainers were similar. Weight was borne fairly evenly on the four casters of the Pacer and Mustang while 85% of the weight was borne on the large wheels of the mid-wheel drive KidWalk. These differences in frame style, wheel, and caster style and overall mass impact inertial properties and forces required to initiate movement. Test results suggest that initiation forces on tile were equivalent for the Pacer and KidWalk while the Mustang had the highest initiation force. Initiation forces on carpet were lowest for the KidWalk and highest for the Mustang. This initial study of inertia and movement initiation forces may provide added information for clinicians to consider when selecting a gait trainer for their clients.

Follow-up actions from positive results of in vitro genetic toxicity testing

EPA Science Inventory

Appropriate follow-up actions and decisions are needed when evaluating and interpreting clear positive results obtained in the in vitro assays used in the initial genotoxicity screening battery (i.e., the battery of tests generally required by regulatory authorities) to assist in...

Effect of initial delamination on Mode 1 and Mode 2 interlaminar fracture toughness and fatigue fracture threshold

NASA Technical Reports Server (NTRS)

Murri, Gretchen Bostaph; Martin, Roderick H.

1991-01-01

Static and fatigue double-cantilever beam (DCB) and end-notch flexure (ENF) tests were conducted to determine the effect of the simulated initial delamination in interlaminar fracture toughness, G(sub c), and fatigue fracture threshold, G(sub th). Unidirectional, 24-ply specimens of S2/SP250 glass/epoxy were tested using Kapton inserts of four different thickness - 13, 25, 75, and 130 microns, at the midplane at one end, or with tension or shear precracks, to simulate an initial delamination. To determine G(sub c), the fatigue fracture threshold below which no delamination growth would occur in less than 1 x 10(exp 6) cycles, fatigue tests were conducted by cyclically loading specimens until delamination growth was detected. Consistent values of model 1 fracture toughness, G(sub Ic), were measured from DCB specimens with inserts of thickness 75 microns or thinner, or with shear precracks. The fatigue DCB tests gave similar values of G(sub Ith) for the 13, 25, and 75 microns specimens. Results for the shear precracked specimens were significantly lower that for specimens without precracks. Results for both the static and fatigue ENF tests showed that measured G(IIc) and G(IIth) values decreased with decreasing insert thickness, so that no limiting thickness could be determined. Results for specimens with inserts of 75 microns or thicker were significantly higher than the results for precracked specimens or specimens with 13 or 25 microns inserts.

Costs of testing for ocular Chlamydia trachomatis infection compared to mass drug administration for trachoma in the Gambia: application of results from the PRET study.

PubMed

Harding-Esch, Emma; Jofre-Bonet, Mireia; Dhanjal, Jaskiran K; Burr, Sarah; Edwards, Tansy; Holland, Martin; Sillah, Ansumana; West, Sheila; Lietman, Tom; Keenan, Jeremy; Mabey, David; Bailey, Robin

2015-04-01

Mass drug administration (MDA) treatment of active trachoma with antibiotic is recommended to be initiated in any district where the prevalence of trachoma inflammation, follicular (TF) is ≥ 10% in children aged 1-9 years, and then to continue for at least three annual rounds before resurvey. In The Gambia the PRET study found that discontinuing MDA based on testing a sample of children for ocular Chlamydia trachomatis(Ct) infection after one MDA round had similar effects to continuing MDA for three rounds. Moreover, one round of MDA reduced disease below the 5% TF threshold. We compared the costs of examining a sample of children for TF, and of testing them for Ct, with those of MDA rounds. The implementation unit in PRET The Gambia was a census enumeration area (EA) of 600-800 people. Personnel, fuel, equipment, consumables, data entry and supervision costs were collected for census and treatment of a sample of EAs and for the examination, sampling and testing for Ct infection of 100 individuals within them. Programme costs and resource savings from testing and treatment strategies were inferred for the 102 EAs in the study area, and compared. Census costs were $103.24 per EA plus initial costs of $108.79. MDA with donated azithromycin cost $227.23 per EA. The mean cost of examining and testing 100 children was $796.90 per EA, with Ct testing kits costing $4.80 per result. A strategy of testing each EA for infection is more expensive than two annual rounds of MDA unless the kit cost is less than $1.38 per result. However stopping or deciding not to initiate treatment in the study area based on testing a sample of EAs for Ct infection (or examining children in a sample of EAs) creates savings relative to further unnecessary treatments. Resources may be saved by using tests for chlamydial infection or clinical examination to determine that initial or subsequent rounds of MDA for trachoma are unnecessary.

Environmentally Benign Battlefield Effects Black Smoke Simulator

DTIC Science & Technology

2006-11-01

tested and results Fuel Oxidizer Color of Smoke Density of Smoke Sugar (Sucrose) KNO3 Grey Medium Dextrin KNO3 Grey Thin Microcrystalline...design. 3.5 Initial Prototype Scale Fiberboard Testing Several quality black smoke formulations were identified in the small pellet testing to

AP-102/104 Retrieval control system qualification test procedure

DOE Office of Scientific and Technical Information (OSTI.GOV)

RIECK, C.A.

1999-05-18

This Qualification Test Procedure documents the results of the qualification testing that was performed on the Project W-211, ''Initial Tank Retrieval Systems,'' retrieval control system (RCS) for tanks 241-AP-102 and 241-AP-104. The results confirm that the RCS has been programmed correctly and that the two related hardware enclosures have been assembled in accordance with the design documents.

Initial Results from the Third Round of Remediated Nitrate Salt Surrogate Formulation and Testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Geoffrey Wayne; Leonard, Philip; Hartline, Ernest Leon

2016-04-20

High explosives science and technology (M-7) is currently working on the third round of formulation and testing of Remediated nitrate salt (RNS) surrogates. This report summarizes the calorimetry results from the 15% sWheat mixtures. All formulation and testing was carried out according to PLAN-TA9-2443 Rev B, "Remediated Nitrate Salt (RNS) surrogate formulation and testing standard procedure", released February 16, 2016. Results from the first and second rounds of formulation and testing were documented in memoranda M7-16-6042 and M7-16-6053.

Optimizing Infant HIV Diagnosis in Resource-Limited Settings: Modeling the Impact of HIV DNA PCR Testing at Birth.

PubMed

Chiu, Alexander; Modi, Surbhi; Rivadeneira, Emilia D; Koumans, Emilia H

2016-12-01

Early antiretroviral therapy (ART) initiation in HIV-infected infants significantly improves survival but is often delayed in resource-limited settings. Adding HIV testing of infants at birth to the current recommendation of testing at age 4-6 weeks may improve testing rates and decrease time to ART initiation. We modeled the benefit of adding HIV testing at birth to the current 6-week testing algorithm. Microsoft Excel was used to create a decision-tree model of the care continuum for the estimated 1,400,000 HIV-infected women and their infants in sub-Saharan Africa in 2012. The model assumed average published rates for facility births (42.9%), prevention of mother-to-child HIV transmission utilization (63%), mother-to-child-transmission rates based on prevention of mother-to-child HIV transmission regimen (5%-40%), return of test results (41%), enrollment in HIV care (52%), and ART initiation (54%). We conducted sensitivity analyses to model the impact of key variables and applied the model to specific country examples. Adding HIV testing at birth would increase the number of infants on ART by 204% by age 18 months. The greatest increase is seen in early ART initiations (543% by age 3 months). The increase would lead to a corresponding increase in survival at 12 months of age, with 5108 fewer infant deaths (44,550, versus 49,658). Adding HIV testing at birth has the potential to improve the number and timing of ART initiation of HIV-infected infants, leading to a decrease in infant mortality. Using this model, countries should investigate a combination of HIV testing at birth and during the early infant period.

Energy Efficiency and Sustainability of Different Building Structures in Latvian Climate

NASA Astrophysics Data System (ADS)

Jakovičs, A.; Gendelis, S.; Bandeniece, L.

2015-11-01

Five experimental test buildings have been built in Riga, Latvia. They are identical except external walls for which different mainly regional building materials are used. Calculated U-values of the other walls, floor and ceiling are the same for each test building. Initial moisture influences the relative humidity of indoor air, which can be higher in the initial time period; as a result, heat transmittances are also very different and cause different heating/cooling energy consumption. Overheating risk in summer exists for test buildings with the smallest thermal inertia. Both summer and heating seasons have been analysed and differences between five test houses have been discussed in details.

Initial results from the Solar Dynamic (SD) Ground Test Demonstration (GTD) project at NASA Lewis

NASA Technical Reports Server (NTRS)

Shaltens, Richard K.; Boyle, Robert V.

1995-01-01

A government/industry team designed, built, and tested a 2 kWe solar dynamic space power system in a large thermal/vacuum facility with a simulated sun at the NASA Lewis Research Center. The Lewis facility provides an accurate simulation of temperatures, high vacuum, and solar flux as encountered in low earth orbit. This paper reviews the goals and status of the Solar Dynamic (SD) Ground Test Demonstration (GTD) program and describes the initial testing, including both operational and performance data. This SD technology has the potential as a future power source for the International Space Station Alpha.

Experiments of thermomechanical fatigue of SMAs

NASA Astrophysics Data System (ADS)

Lagoudas, Dimitris C.; Miller, David A.

1999-07-01

As SMA wires are gaining in popularity for use as actuators, one constitutive parameter that remain unknown is the thermomechanical fatigue life. Even though the effect of thermal cycles on the transformation characteristics of SMAs has been studied, these teste have not been extended to high number of cycles. In this study, a novel test frame developed to study the thermomechanical fatigue life of SMAs is described. Additionally, a testing protocol is discussed necessary to fully establish the fatigue characteristics of SMAs under various conditions. Initial results of the initial test show a substantial increase in the number of cycles to failure as the applied stress level reduces to approximately 100 MPa.

Evaluation of the BT-1 serum assay for breast cancer.

PubMed

Whitehurst, M M; Aldenderfer, P H; Sooy, M M; Strelkauskas, A J

1999-01-01

The BT-1 assay which identifies a novel breast tumor associated serum analyte was performed for 143 patients previously diagnosed with breast cancer. Mucin tumor markers CA15-3/CA27-29 values were available for 50 patients and there was very minor overlap between patients positive by both tests. Patients' follow-up clinical status at sample draw was compared to BT-1 assay results. 27% of patients originally diagnosed as Stage II and 20% patients originally diagnosed as Stage III who were evaluated 'no disease' had positive BT-1 values. 8% patients diagnosed as Stage II had negative BT-1 results in samples drawn within 90 days of chemotherapy initiation, whereas 23% of patients diagnosed as Stage III cancer were BT-1 test positive within 90 days of chemotherapy initiation. 50% of patients tested before initial breast cancer surgery had positive BT-1 values, suggesting that the BT-1 assay may be useful in identification women with more advanced disease at diagnosis.

DCT Trigger in a High-Resolution Test Platform for the Detection of Very Inclined Showers in Pierre Auger Surface Detectors

NASA Astrophysics Data System (ADS)

Szadkowski, Zbigniew; Wiedeński, Michał

2017-06-01

We present first results from a trigger based on the discrete cosine transform (DCT) operating in new front-end boards with a Cyclone V E field-programmable gate array (FPGA) deployed in seven test surface detectors in the Pierre Auger Test Array. The patterns of the ADC traces generated by very inclined showers (arriving at 70° to 90° from the vertical) were obtained from the Auger database and from the CORSIKA simulation package supported by the Auger OffLine event reconstruction platform that gives predicted digitized signal profiles. Simulations for many values of the initial cosmic ray angle of arrival, the shower initialization depth in the atmosphere, the type of particle, and its initial energy gave a boundary on the DCT coefficients used for the online pattern recognition in the FPGA. Preliminary results validated the approach used. We recorded several showers triggered by the DCT for 120 Msamples/s and 160 Msamples/s.

Testing and modeling of PBX-9591 shock initiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lam, Kim; Foley, Timothy; Novak, Alan

2010-01-01

This paper describes an ongoing effort to develop a detonation sensitivity test for PBX-9501 that is suitable for studying pristine and damaged HE. The approach involves testing and comparing the sensitivities of HE pressed to various densities and those of pre-damaged samples with similar porosities. The ultimate objectives are to understand the response of pre-damaged HE to shock impacts and to develop practical computational models for use in system analysis codes for HE safety studies. Computer simulation with the CTH shock physics code is used to aid the experimental design and analyze the test results. In the calculations, initiation andmore » growth or failure of detonation are modeled with the empirical HVRB model. The historical LANL SSGT and LSGT were reviewed and it was determined that a new, modified gap test be developed to satisfy the current requirements. In the new test, the donor/spacer/acceptor assembly is placed in a holder that is designed to work with fixtures for pre-damaging the acceptor sample. CTH simulations were made of the gap test with PBX-9501 samples pressed to three different densities. The calculated sensitivities were validated by test observations. The agreement between the computed and experimental critical gap thicknesses, ranging from 9 to 21 mm under various test conditions, is well within 1 mm. These results show that the numerical modeling is a valuable complement to the experimental efforts in studying and understanding shock initiation of PBX-9501.« less

Duration of Group A Streptococcus PCR positivity following antibiotic treatment of pharyngitis.

PubMed

Homme, Jason H; Greenwood, Corryn S; Cronk, Lisa B; Nyre, Lisa M; Uhl, James R; Weaver, Amy L; Patel, Robin

2018-02-01

Polymerase chain reaction (PCR) has high sensitivity and specificity for detection of group A streptococcus (GAS) in throat swabs and is routinely used for GAS pharyngitis diagnosis at our institution. Herein we defined the natural history of throat swab GAS PCR and culture positivity during and following treatment of GAS pharyngitis. Fifty children with a PCR positive GAS throat swab were recruited for participation. Four additional throat swabs were collected over 2 weeks following the initial positive PCR result (during and following a standard course of antibiotic therapy) and tested for GAS using rapid real-time PCR and culture. After the initial positive swab, 45% had a positive PCR 2-4 days, 20% 5-7 days, 18% 8-10 days, 25% 11-13days, and 20% 14-18days later. The median time to a negative PCR was 4 days with the nadir in positive PCR results approximating the end of a typical 10-day treatment interval. Seven subjects remained persistently PCR positive. Culture results remained positive at a stable rate for each time interval, ranging from 5-10%. If a patient presents with symptoms of GAS pharyngitis after previous positive GAS PCR testing and treatment with appropriate antibiotics, it is reasonable to use PCR testing for GAS pharyngitis testing beginning one week after initial testing. Further studies are warranted to determine if this time frame can be applied to PCR testing used to detect other infections. Copyright © 2017 Elsevier Inc. All rights reserved.

The influence of cutting speed and cutting initiation location in specimen preparation for the microtensile bond strength test.

PubMed

Abreu, Celina Wanderley; Santosb, Jarbas F; Passos, Sheila Pestana; Michida, Silvia Masae; Takahashi, Fernando Eidi; Bottino, Marco Antonio

2011-06-01

This study evaluated the effect of cutting initiation location and cutting speed on the bond strength between resin cement and feldspathic ceramic. Thirty-six blocks (6.4 x 6.4 x 4.8 mm) of ceramic (Vita VM7) were produced. The ceramic surfaces were etched with 10% hydrofluoric acid gel for 60 s and then silanized. Each ceramic block was placed in a silicon mold with the treated surface exposed. A resin cement (Variolink II) was injected into the mold over the treated surface and polymerized. The resin cement-ceramic blocks were divided into two groups according to experimental conditions: a) cutting initiation location - resin cement, ceramic and interface; and b) cutting speed - 10,000, 15,000, and 20,000 rpm. The specimens were sectioned to achieve non-trimmed bar specimens. The microtensile test was performed in a universal testing machine (1 mm/min). The failure modes were examined using an optical light microscope and SEM. Bond strength results were analyzed using one-way ANOVA and Tukey's test (α = 0.05). Significant influences of cutting speed and initiation location on bond strength (p < 0.05) were observed. The highest mean was achieved for specimens cut at 15,000 rpm at the interface (15.12 ± 5.36 MPa). The lowest means were obtained for specimens cut at the highest cutting speed in resin cement (8.50 ± 3.27 MPa), and cut at the lowest cutting speed in ceramic (8.60 ± 2.65 MPa). All groups showed mainly mixed failure (75% to 100%). The cutting speed and initiation location are important factors that should be considered during specimen preparation for microtensile bond strength testing, as both may influence the bond strength results.

Initial Results of Multigene Panel Testing for Hereditary Breast and Ovarian Cancer and Lynch Syndrome.

PubMed

Howarth, Dt R; Lum, Sharon S; Esquivel, Pamela; Garberoglio, Carlos A; Senthil, Maheswari; Solomon, Naveenraj L

2015-10-01

Multigene panel testing for hereditary cancer risk has recently become commercially available; however, the impact of its use on patient care is undefined. We sought to evaluate results from implementation of panel testing in a multidisciplinary cancer center. We performed a retrospective review of consecutive patients undergoing genetic testing after initiating use of multigene panel testing at Loma Linda University Medical Center. From February 13 to August 25, 2014, 92 patients were referred for genetic testing based on National Comprehensive Cancer Network guidelines. Testing was completed in 90 patients. Overall, nine (10%) pathogenic mutations were identified: five BRCA1/2, and four in non-BRCA loci. Single-site testing identified one BRCA1 and one BRCA2 mutation. The remaining mutations were identified by use of panel testing for hereditary breast and ovarian cancer. There were 40 variants of uncertain significance identified in 34 patients. The use of panel testing more than doubled the identification rate of clinically significant pathogenic mutations that would have been missed with BRCA testing alone. The large number of variants of uncertain significance identified will require long-term follow-up for potential reclassification. Multigene panel testing provides additional information that may improve patient outcomes.

Screening HIV-Infected Patients with Low CD4 Counts for Cryptococcal Antigenemia prior to Initiation of Antiretroviral Therapy: Cost Effectiveness of Alternative Screening Strategies in South Africa

PubMed Central

Rockers, Peter C.; Bonawitz, Rachael; Sriruttan, Charlotte; Glencross, Deborah K.; Cassim, Naseem; Coetzee, Lindi M.; Greene, Gregory S.; Chiller, Tom M.; Vallabhaneni, Snigdha; Long, Lawrence; van Rensburg, Craig; Govender, Nelesh P.

2016-01-01

Background In 2015 South Africa established a national cryptococcal antigenemia (CrAg) screening policy targeted at HIV-infected patients with CD4+ T-lymphocyte (CD4) counts <100 cells/ μl who are not yet on antiretroviral treatment (ART). Two screening strategies are included in national guidelines: reflex screening, where a CrAg test is performed on remnant blood samples from CD4 testing; and provider-initiated screening, where providers order a CrAg test after a patient returns for CD4 test results. The objective of this study was to compare costs and effectiveness of these two screening strategies. Methods We developed a decision analytic model to compare reflex and provider-initiated screening in terms of programmatic and health outcomes (number screened, number identified for preemptive treatment, lives saved, and discounted years of life saved) and screening and treatment costs (2015 USD). We estimated a base case with prevalence and other parameters based on data collected during CrAg screening pilot projects integrated into routine HIV care in Gauteng, Free State, and Western Cape Provinces. We conducted sensitivity analyses to explore how results change with underlying parameter assumptions. Results In the base case, for each 100,000 CD4 tests, the reflex strategy compared to the provider-initiated strategy has higher screening costs ($37,536 higher) but lower treatment costs ($55,165 lower), so overall costs of screening and treatment are $17,629 less with the reflex strategy. The reflex strategy saves more lives (30 lives, 647 additional years of life saved). Sensitivity analyses suggest that reflex screening dominates provider-initiated screening (lower total costs and more lives saved) or saves additional lives for small additional costs (< $125 per life year) across a wide range of conditions (CrAg prevalence, patient and provider behavior, patient survival without treatment, and effectiveness of preemptive fluconazole treatment). Conclusions In countries with substantial numbers of people with untreated, advanced HIV disease such as South Africa, CrAg screening before initiation of ART has the potential to reduce cryptococcal meningitis and save lives. Reflex screening compared to provider-initiated screening saves more lives and is likely to be cost saving or have low additional costs per additional year of life saved. PMID:27390864

Crew Module Overview

NASA Technical Reports Server (NTRS)

Redifer, Matthew E.

2011-01-01

The presentation presents an overview of the Crew Module development for the Pad Abort 1 flight test. The presentation describes the integration activity from the initial delivery of the primary structure through the installation of vehicle subsystems, then to flight test. A brief overview of flight test results is given.

Train-to-train impact test : analysis of structural measurements

DOT National Transportation Integrated Search

2002-11-17

This paper describes the results of the train-to-train impact test conducted at the Transportation Technology Center in Pueblo, Colorado on January 31, 2002. In this test, a cab car-led train, initially moving at 30 mph, collided with a standing loco...

Initial evaluation tests of General Electric Company 12.0 ampere hour nickel cadmium spacecraft cells with design variables

NASA Technical Reports Server (NTRS)

Harkness, J. D.

1979-01-01

All evaluation tests were performed at room ambient pressure and temperature, with discharges at a 2 hour rate. Tests consisted of phenolphthalein leak tests, three capacity tests, an auxiliary electrode test, a charge retention test, an internal short test, a charge efficiency test, overcharge tests, and a pressure versus capacity test. Results of the tests and recommendations for improvements in manufacturing are presented.

Test of LOX compatibility for asphalt and concrete runway materials

NASA Technical Reports Server (NTRS)

Moyers, C. V.; Bryan, C. J.; Lockhart, B. J.

1973-01-01

A literature survey and a telephone canvass of producers and users of LOX is reported which yielded one report of an accident resulting from a LOX spill on asphalt, one discussion of hazardous conditions, and an unreferenced mention of an incident. Laboratory tests using standard LOX impact apparatus yielded reactions with both old and new alphalt, but none with concrete. In the final test, using a larger sample of asphalt, the reaction caused extensive damage to equipment. Initial field experiments using 2-meter square asphalt slabs covered with LOX, conducted during rainy weather, achieved no reaction with plummets, and limited reaction with a blasting cap as a reaction initiator. In a final plummet-initiated test on a dry slab, a violent reaction, which appeared to have propagated over the entire slab surface, destroyed the plummet fixture and threw fragments as far as 48 meters.

Does universal active MRSA surveillance influence anti-MRSA antibiotic use? A retrospective analysis of the treatment of patients admitted with suspicion of infection at Veterans Affairs Medical Centers between 2005 and 2010.

PubMed

Jones, Makoto; Huttner, Benedikt; Leecaster, Molly; Huttner, Angela; Damal, Kavitha; Tanner, Windy; Nielson, Christopher; Rubin, Michael A; Goetz, Matthew Bidwell; Madaras-Kelly, Karl; Samore, Matthew H

2014-12-01

After the implementation of an active surveillance programme for MRSA in US Veterans Affairs (VA) Medical Centers, there was an increase in vancomycin use. We investigated whether positive MRSA admission surveillance tests were associated with MRSA-positive clinical admission cultures and whether the availability of surveillance tests influenced prescribers' ability to match initial anti-MRSA antibiotic use with anticipated MRSA results from clinical admission cultures. Analyses were based on barcode medication administration data, microbiology data and laboratory data from 129 hospitals between January 2005 and September 2010. Hospitalized patient admissions were included if clinical cultures were obtained and antibiotics started within 2 days of admission. Mixed-effects logistic regression was used to examine associations between positive MRSA admission cultures and (i) admission MRSA surveillance test results and (ii) initial anti-MRSA therapy. Among 569,815 included admissions, positive MRSA surveillance tests were strong predictors of MRSA-positive admission cultures (OR 8.5; 95% CI 8.2-8.8). The negative predictive value of MRSA surveillance tests was 97.6% (95% CI 97.5%-97.6%). The diagnostic OR between initial anti-MRSA antibiotics and MRSA-positive admission cultures was 3.2 (95% CI 3.1-3.4) for patients without surveillance tests and was not significantly different for admissions with surveillance tests. The availability of nasal MRSA surveillance tests in VA hospitals did not seem to improve the ability of prescribers to predict the necessity of initial anti-MRSA treatment despite the high negative predictive value of MRSA surveillance tests. Prospective trials are needed to establish the safety and effectiveness of using MRSA surveillance tests to guide antibiotic therapy. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy 2014. This work is written by (a) US Government employee(s) and is in the public domain in the US.

Reuse of acid coagulant-recovered drinking waterworks sludge residual to remove phosphorus from wastewater

NASA Astrophysics Data System (ADS)

Yang, Lan; Wei, Jie; Zhang, Yumei; Wang, Jianli; Wang, Dongtian

2014-06-01

Acid coagulant-recovered drinking waterworks sludge residual (DWSR) is a waste product from drinking waterworks sludge (DWS) treatment with acid for coagulant recovery. In this study, we evaluated DWSR as a potential phosphorus (P) removing material in wastewater treatment by conducting a series of batch and semi-continuous tests. Batch tests were carried out to study the effects of pH, initial concentration, and sludge dose on P removal. Batch test results showed that the P removal efficiency of DWSR was highly dependent on pH. Calcinated DWSR (C-DWSR) performed better in P removal than DWSR due to its higher pH. At an optimum initial pH value of 5-6 and a sludge dose of 10 g/L, the P removal rates of DWSR and DWS decreased from 99% and 93% to 84% and 14%, respectively, and the specific P uptake of DWSR and DWS increased from 0.19 and 0.19 mg P/g to 33.60 and 5.72 mg P/g, respectively, when the initial concentration was increased from 2 to 400 mg/L. The effective minimum sludge doses of DWSR and DWS were 0.5 g/L and 10 g/L, respectively, when the P removal rates of 90% were obtained at an initial concentration of 10 mg/L. Results from semi-continuous test indicated that P removal rates over 99% were quickly achieved for both synthetic and actual wastewater (lake water and domestic sewage). These rates could be maintained over a certain time under a certain operational conditions including sludge dose, feed flow, and initial concentration. The physicochemical properties analysis results showed that the contents of aluminum (Al) and iron (Fe) in DWSR were reduced by 50% and 70%, respectively, compared with DWS. The insoluble Al and Fe hydroxide in DWS converted into soluble Al and Fe in DWSR. Metal leaching test results revealed that little soluble Al and Fe remained in effluent when DWSR was used for P removal. We deduced that chemical precipitation might be the major action for P removal by DWSR and that adsorption played only a marginal role.

Impact on ART initiation of point-of-care CD4 testing at HIV diagnosis among HIV-positive youth in Khayelitsha, South Africa.

PubMed

Patten, Gabriela E M; Wilkinson, Lynne; Conradie, Karien; Isaakidis, Petros; Harries, Anthony D; Edginton, Mary E; De Azevedo, Virginia; van Cutsem, Gilles

2013-07-04

Despite the rapid expansion of antiretroviral therapy (ART) programmes in developing countries, pre-treatment losses from care remain a challenge to improving access to treatment. Youth and adolescents have been identified as a particularly vulnerable group, at greater risk of loss from both pre-ART and ART care. Point-of-care (POC) CD4 testing has shown promising results in improving linkage to ART care. In Khayelitsha township, South Africa, POC CD4 testing was implemented at a clinic designated for youth aged 12-25 years. We assessed whether there was an associated reduction in attrition between HIV testing, assessment for eligibility and ART initiation. A before-and-after observational study was conducted using routinely collected data. These were collected on patients from May 2010 to April 2011 (Group A) when baseline CD4 count testing was performed in a laboratory and results were returned to the clinic within two weeks. Same-day POC CD4 testing was implemented in June 2011, and data were collected on patients from August 2011 to July 2012 (Group B). A total of 272 and 304 youth tested HIV-positive in Group A and Group B, respectively. Group B patients were twice as likely to have their ART eligibility assessed compared to Group A patients: 275 (90%) vs. 183 (67%) [relative risk (RR)=2.4, 95% CI: 1.8-3.4, p<0.0001]. More patients in World Health Organization (WHO) Stage 1 disease (85% vs. 69%), with CD4 counts≥350 cells/µL (58% vs. 35%) and more males (13% vs. 7%) were detected in Group B. The proportion of eligible patients who initiated ART was 50% and 44% (p=0.6) in Groups B and A, respectively; and 50% and 43% (p=0.5) when restricted to patients with baseline CD4 count≤250 cells/µL. Time between HIV-testing and ART initiation was reduced from 36 to 28 days (p=0.6). POC CD4 testing significantly improved assessment for ART eligibility. The improvement in the proportion initiating ART and the reduction in time to initiation was not significant due to sample size limitations. POC CD4 testing reduced attrition between HIV-testing and assessment of ART eligibility. Strategies to improve uptake of ART are needed, possibly by improving patient support for HIV-positive youth immediately after diagnosis.

Laboratory Evaluation of EGS Shear Stimulation-Test 001

DOE Data Explorer

Bauer, Steve

2014-07-29

this is the results of an initial setup-shakedon test in order to develop the plumbing system for this test design. a cylinder of granite with offset holes was jacketed and subjected to confining pressure and low temperature (85C) and pore water pressure. flow through the sample was developed at different test stages.

Bypass control valve seal and bearing life cycle test report

NASA Technical Reports Server (NTRS)

Lundback, A. V.

1972-01-01

The operating characteristics of a bypass control valve seal and bearing life cycle tests are reported. Data from the initial assembly, leak, torque, and deflection tests are included along with the cycle life test results and conclusions. The equipment involved was to be used in the nuclear engine for the rocket vehicles program.

Evaluation Of Risk And Possible Mitigation Schemes For Previously Unidentified Hazards

NASA Technical Reports Server (NTRS)

Linzey, William; McCutchan, Micah; Traskos, Michael; Gilbrech, Richard; Cherney, Robert; Slenski, George; Thomas, Walter, III

2006-01-01

This report presents the results of arc track testing conducted to determine if such a transfer of power to un-energized wires is possible and/or likely during an arcing event, and to evaluate an array of protection schemes that may significantly reduce the possibility of such a transfer. The results of these experiments may be useful for determining the level of protection necessary to guard against spurious voltage and current being applied to safety critical circuits. It was not the purpose of these experiments to determine the probability of the initiation of an arc track event only if an initiation did occur could it cause the undesired event: an inadvertent thruster firing. The primary wire insulation used in the Orbiter is aromatic polyimide, or Kapton , a construction known to arc track under certain conditions [3]. Previous Boeing testing has shown that arc tracks can initiate in aromatic polyimide insulated 28 volts direct current (VDC) power circuits using more realistic techniques such as chafing with an aluminum blade (simulating the corner of an avionics box or lip of a wire tray), or vibration of an aluminum plate against a wire bundle [4]. Therefore, an arc initiation technique was chosen that provided a reliable and consistent technique of starting the arc and not a realistic simulation of a scenario on the vehicle. Once an arc is initiated, the current, power and propagation characteristics of the arc depend on the power source, wire gauge and insulation type, circuit protection and series resistance rather than type of initiation. The initiation method employed for these tests was applying an oil and graphite mixture to the ends of a powered twisted pair wire. The flight configuration of the heater circuits, the fuel/oxider (or ox) wire, and the RCS jet solenoid were modeled in the test configuration so that the behavior of these components during an arcing event could be studied. To determine if coil activation would occur with various protection wire schemes, 145 tests were conducted using various fuel/ox wire alternatives (shielded and unshielded) and/or different combinations of polytetrafuloroethylene (PTFE), Mystik tape and convoluted wraps to prevent unwanted coil activation. Test results were evaluated along with other pertinent data and information to develop a mitigation strategy for an inadvertent RCS firing. The SSP evaluated civilian aircraft wiring failures to search for aging trends in assessing the wire-short hazard. Appendix 2 applies Weibull statistical methods to the same data with a similar purpose.

IDAS : ITS Deployment Analysis System

DOT National Transportation Integrated Search

1997-05-01

This report documents the activities and results of a 2-year test of non-intrusive traffic detection technologies. The test was initiated by the Federal Highway Administration (FHWA) and conducted by the Minnesota Department of Transportation (Mn/DOT...

Twenty Years On!: Updating the IEA BESTEST Building Thermal Fabric Test Cases for ASHRAE Standard 140

DOE Office of Scientific and Technical Information (OSTI.GOV)

Judkoff, R.; Neymark, J.

2013-07-01

ANSI/ASHRAE Standard 140, Standard Method of Test for the Evaluation of Building Energy Analysis Computer Programs applies the IEA BESTEST building thermal fabric test cases and example simulation results originally published in 1995. These software accuracy test cases and their example simulation results, which comprise the first test suite adapted for the initial 2001 version of Standard 140, are approaching their 20th anniversary. In response to the evolution of the state of the art in building thermal fabric modeling since the test cases and example simulation results were developed, work is commencing to update the normative test specification and themore » informative example results.« less

Twenty Years On!: Updating the IEA BESTEST Building Thermal Fabric Test Cases for ASHRAE Standard 140: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Judkoff, R.; Neymark, J.

2013-07-01

ANSI/ASHRAE Standard 140, Standard Method of Test for the Evaluation of Building Energy Analysis Computer Programs applies the IEA BESTEST building thermal fabric test cases and example simulation results originally published in 1995. These software accuracy test cases and their example simulation results, which comprise the first test suite adapted for the initial 2001 version of Standard 140, are approaching their 20th anniversary. In response to the evolution of the state of the art in building thermal fabric modeling since the test cases and example simulation results were developed, work is commencing to update the normative test specification and themore » informative example results.« less

Small Wind Research Turbine: Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corbus, D.; Meadors, M.

2005-10-01

The Small Wind Research Turbine (SWRT) project was initiated to provide reliable test data for model validation of furling wind turbines and to help understand small wind turbine loads. This report will familiarize the user with the scope of the SWRT test and support the use of these data. In addition to describing all the testing details and results, the report presents an analysis of the test data and compares the SWRT test data to simulation results from the FAST aeroelastic simulation model.

A Study on the Mechanical Properties and Impact-Induced Initiation Characteristics of Brittle PTFE/Al/W Reactive Materials.

PubMed

Ge, Chao; Maimaitituersun, Wubuliaisan; Dong, Yongxiang; Tian, Chao

2017-04-26

Polytetrafluoroethylene/aluminum/tungsten (PTFE/Al/W) reactive materials of three different component mass ratios (73.5/26.5/0, 68.8/24.2/7 and 63.6/22.4/14) were studied in this research. Different from the PTFE/Al/W composites published elsewhere, the materials in our research were fabricated under a much lower sintering temperature and for a much shorter duration to achieve a brittle property, which aims to provide more sufficient energy release upon impact. Quasi-static compression tests, dynamic compression tests at room and elevated temperatures, and drop weight tests were conducted to evaluate the mechanical and impact-induced initiation characteristics of the materials. The materials before and after compression tests were observed by a scanning electron microscope to relate the mesoscale structural characteristics to their macro properties. All the three types of materials fail at very low strains during both quasi-static and dynamic compression. The stress-strain curves for quasi-static tests show obvious deviations while that for the dynamic tests consist of only linear-elastic and failure stages typically. The materials were also found to exhibit thermal softening at elevated temperatures and were strain-rate sensitive during dynamic tests, which were compared using dynamic increase factors (DIFs). Drop-weight test results show that the impact-initiation sensitivity increases with the increase of W content due to the brittle mechanical property. The high-speed video sequences and recovered sample residues of the drop-weight tests show that the reaction is initiated at two opposite positions near the edges of the samples, where the shear force concentrates the most intensively, indicating a shear-induced initiation mechanism.

A Study on the Mechanical Properties and Impact-Induced Initiation Characteristics of Brittle PTFE/Al/W Reactive Materials

PubMed Central

Ge, Chao; Maimaitituersun, Wubuliaisan; Dong, Yongxiang; Tian, Chao

2017-01-01

Polytetrafluoroethylene/aluminum/tungsten (PTFE/Al/W) reactive materials of three different component mass ratios (73.5/26.5/0, 68.8/24.2/7 and 63.6/22.4/14) were studied in this research. Different from the PTFE/Al/W composites published elsewhere, the materials in our research were fabricated under a much lower sintering temperature and for a much shorter duration to achieve a brittle property, which aims to provide more sufficient energy release upon impact. Quasi-static compression tests, dynamic compression tests at room and elevated temperatures, and drop weight tests were conducted to evaluate the mechanical and impact-induced initiation characteristics of the materials. The materials before and after compression tests were observed by a scanning electron microscope to relate the mesoscale structural characteristics to their macro properties. All the three types of materials fail at very low strains during both quasi-static and dynamic compression. The stress-strain curves for quasi-static tests show obvious deviations while that for the dynamic tests consist of only linear-elastic and failure stages typically. The materials were also found to exhibit thermal softening at elevated temperatures and were strain-rate sensitive during dynamic tests, which were compared using dynamic increase factors (DIFs). Drop-weight test results show that the impact-initiation sensitivity increases with the increase of W content due to the brittle mechanical property. The high-speed video sequences and recovered sample residues of the drop-weight tests show that the reaction is initiated at two opposite positions near the edges of the samples, where the shear force concentrates the most intensively, indicating a shear-induced initiation mechanism. PMID:28772812

Microstructural examination of

NASA Astrophysics Data System (ADS)

Fukuoka, C.; Yoshizawa, H.; Nakagawa, Y. G.; Lapides, M. E.

1993-10-01

Fatigue tests were performed to examine how microstructural conditioning influences crack initiation and propagation in SA508 class 3 low-carbon steel. A 3-mm-long crack was introduced in compact tension (CT) fatigue test specimens under four different loads in order to obtain crack tip plastic zones at different stress intensity factor ranges, ΔK = 18, 36, 54, and 72 MPa√m. The microstructure of the plastic zones around the crack tip were examined by trans- mission electron microscopy (TEM) and selected area electron diffraction (SAD). Micro- orientation of the dislocation cells in the plastic zones of all of the CT samples increased to 4 deg from the level of an as-received sample. Four-point bending fatigue tests were performed for plate shape samples with a large cyclic strain range. The SAD value of the bending samples was also 4 deg in the damaged area where cracks already initiated at an early stage of the fatigue process. These test results indicate that the microstructural conditioning is a prerequisite for the fatigue crack initiation and propagation in SA508. These observations may lead to better under- standing of how fatigue initiation processes transit to cracks.

Dry and wet arc track propagation resistance testing

NASA Technical Reports Server (NTRS)

Beach, Rex

1995-01-01

The wet arc-propagation resistance test for wire insulation provides an assessment of the ability of an insulation to prevent damage in an electrical environment. Results of an arc-propagation test may vary slightly due to the method of arc initiation; therefore a standard test method must be selected to evaluate the general arc-propagation resistance characteristics of an insulation. This test method initiates an arc by dripping salt water over pre-damaged wires which creates a conductive path between the wires. The power supply, test current, circuit resistances, and other variables are optimized for testing 20 guage wires. The use of other wire sizes may require modifications to the test variables. The dry arc-propagation resistance test for wire insulation also provides an assessment of the ability of an insulation to prevent damage in an electrical arc environment. In service, electrical arcs may originate form a variety of factors including insulation deterioration, faulty installation, and chafing. Here too, a standard test method must be selected to evaluate the general arc-propagation resistance characteristics of an insulation. This test method initiates an arc with a vibrating blade. The test also evaluates the ability of the insulation to prevent further arc-propagation when the electrical arc is re-energized.

Pyrotechnic shock at the orbiter/external tank forward attachment

NASA Technical Reports Server (NTRS)

Rogers, W. F.; Grissom, D. S.; Rhodes, L. R.

1980-01-01

During the initial certification test of the forward structural attachment of the space shuttle orbiter to the external tank, pyrotechnic shock from actuation of the separation device resulted in structural failure of the thermal protection tiles surrounding the attachment. Because of the high shock associated with the separation bolt, the development of alternative low shock separation designs was initiated. Two concepts that incorporate a 5.08 centimeter frangible nut as the release device were developed and tested.

Effects of {10-12} Twins on Dynamic Torsional Properties of Extruded AZ31 Magnesium Alloy

NASA Astrophysics Data System (ADS)

Lee, Jong Un; Song, Seok Weon; Kim, Yongjin; Kim, Sang-Hoon; Kim, Ye Jin; Park, Sung Hyuk

2018-03-01

Effects of initial twins on dynamic torsional properties of extruded AZ31 alloy were investigated by introducing {10-12} twins into it through precompression to 3 and 6% strains along the extrusion direction and performing torsional testing at a strain rate of 1.4 × 103 s-1 using a torsional Kolsky bar system. The as-extruded sample without twins showed higher dynamic torsional properties than the precompressed samples with many initial twins; the maximum shear strength and fracture shear strain decreased with increasing amount of initial twins. In the as-extruded sample, twinning occurred vigorously throughout the gage section of the tubular specimen during high-strain-rate torsional tests, resulting in heavily deformed morphology, many macrocracks, and rough fractured surfaces. The increased amount of initial twins suppressed the twinning behavior and localized the applied torsional deformation; this resulted in an almost unchanged sample shape, no secondary cracks, and a flat fracture plane, thereby deteriorating the dynamic torsional properties of the extruded alloy.

[Benefits of using rapid HIV testing at the PMU-FLON walk-in clinic in Lausanne].

PubMed

Gilgien, W; Aubert, J; Bischoff, T; Herzig, L; Perdrix, J

2012-05-16

Lab tests are frequently used in primary care to guide patient care. This is particularly the case when a severe disorder, or one that will affect patients' initial care, needs to be excluded rapidly. At the PMU-FLON walk-in clinic the use of HIV testing as recommended by the Swiss Office of Public Health was hampered by the delay in obtaining test results. This led us to introduce rapid HIV testing which provides results within 30 minutes. Following the first 250 tests the authors discuss the results as well as the benefits of rapid HIV testing in an urban walk-in clinic.

Loss to Follow-Up from HIV Screening to ART Initiation in Rural China

PubMed Central

Gu, Diane; Mao, Yurong; Tang, Zhenzhu; Montaner, Julio; Shen, Zhiyong; Zhu, Qiuying; Detels, Roger; Jin, Xia; Xiong, Ran; Xu, Juan; Ling, Walter; Erinoff, Lynda; Lindblad, Robert; Liu, David; Van Veldhuisen, Paul; Hasson, Albert; Wu, Zunyou

2016-01-01

Background Patients who are newly screened HIV positive by EIA are lost to follow-up due to complicated HIV testing procedures. Because this is the first step in care, it affects the entire continuum of care. This is a particular concern in rural China. Objective(s) To assess the routine HIV testing completeness and treatment initiation rates at 18 county-level general hospitals in rural Guangxi. Methods We reviewed original hospital HIV screening records. Investigators also engaged with hospital leaders and key personnel involved in HIV prevention activities to characterize in detail the routine care practices in place at each county. Results 699 newly screened HIV-positive patients between January 1 and June 30, 2013 across the 18 hospitals were included in the study. The proportion of confirmatory testing across the 18 hospitals ranged from 14% to 87% (mean of 43%), and the proportion of newly diagnosed individuals successfully initiated antiretroviral treatment across the hospitals ranged from 3% to 67% (mean of 23%). The average interval within hospitals for individuals to receive the Western Blot (WB) and CD4 test results from HIV positive screening (i.e. achieving testing completion) ranged from 14–116 days (mean of 41.7 days) across the hospitals. The shortest interval from receiving a positive EIA screening test result to receiving WB and CD4 testing and counseling was 0 day and the longest was 260 days. Conclusion The proportion of patients newly screened HIV positive that completed the necessary testing procedures for HIV confirmation and received ART was very low. Interventions are urgently needed to remove barriers so that HIV patients can have timely access to HIV/AIDS treatment and care in rural China. PMID:27768710

241-AZ-101 Waste Tank Color Video Camera System Shop Acceptance Test Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

WERRY, S.M.

2000-03-23

This report includes shop acceptance test results. The test was performed prior to installation at tank AZ-101. Both the camera system and camera purge system were originally sought and procured as a part of initial waste retrieval project W-151.

Urine and oral fluid drug testing in support of pain management.

PubMed

Kwong, Tai C; Magnani, Barbarajean; Moore, Christine

2017-09-01

In recent years, the abuse of opioid drugs has resulted in greater prevalence of addiction, overdose, and deaths attributable to opioid abuse. The epidemic of opioid abuse has prompted professional and government agencies to issue practice guidelines for prescribing opioids to manage chronic pain. An important tool available to providers is the drug test for use in the initial assessment of patients for possible opioid therapy, subsequent monitoring of compliance, and documentation of suspected aberrant drug behaviors. This review discusses the issues that most affect the clinical utility of drug testing in chronic pain management with opioid therapy. It focuses on the two most commonly used specimen matrices in drug testing: urine and oral fluid. The advantages and disadvantages of urine and oral fluid in the entire testing process, from specimen collection and analytical methodologies to result interpretation are reviewed. The analytical sensitivity and specificity limitations of immunoassays used for testing are examined in detail to draw attention to how these shortcomings can affect result interpretation and influence clinical decision-making in pain management. The need for specific identification and quantitative measurement of the drugs and metabolites present to investigate suspected aberrant drug behavior or unexpected positive results is analyzed. Also presented are recent developments in optimization of test menus and testing strategies, such as the modification of the standard screen and reflexed-confirmation testing model by eliminating some of the initial immunoassay-based tests and proceeding directly to definitive testing by mass spectrometry assays.

Design, fabrication and testing of an optical temperature sensor

NASA Technical Reports Server (NTRS)

Morey, W. W.; Glenn, W. H.; Decker, R. O.; Mcclurg, W. C.

1980-01-01

The laboratory breadboard optical temperature sensor based on the temperature dependent absorptive characteristics of a rare earth (europium) doped optical fiber. The principles of operation, materials characterization, fiber and optical component design, design and fabrication of an electrooptic interface unit, signal processing, and initial test results are discussed. Initial tests indicated that, after a brief warmup period, the output of the sensor was stable to approximately 1 C at room temperature or approximately + or - 0.3 percent of point (K). This exceeds the goal of 1 percent of point. Recommendations are presented for further performance improvement.

Initial testing of a variable-stroke Stirling engine

NASA Technical Reports Server (NTRS)

Thieme, L. G.

1985-01-01

In support of the U.S. Department of Energy's Stirling Engine Highway Vehicle Systems Program, NASA Lewis Research Center is evaluating variable-stroke control for Stirling engines. The engine being tested is the Advenco Stirling engine; this engine was manufactured by Philips Research Laboratories of the Netherlands and uses a variable-angle swash-plate drive to achieve variable stroke operation. The engine is described, initial steady-state test data taken at Lewis are presented, a major drive system failure and subsequent modifications are described. Computer simulation results are presented to show potential part-load efficiency gains with variable-stroke control.

Dynamic Fracture Initiation Toughness at Elevated Temperatures With Application to the New Generation of Titanium Aluminide Alloys. Chapter 8

NASA Technical Reports Server (NTRS)

Shazly, Mostafa; Prakash, Vikas; Draper, Susan; Shukla, Arun (Editor)

2006-01-01

Recently, a new generation of titanium aluminide alloy, named Gamma-Met PX, has been developed with better rolling and post-rolling characteristics. I'revious work on this alloy has shown the material to have higher strengths at room and elevated temperatures when compared with other gamma titanium aluminides. In particular, this new alloy has shown increased ductility at elevated temperatures under both quasi-static and high strain rate uniaxial compressive loading. However, its high strain rate tensile ductility at room and elevated temperatures is limited to approx. 1%. In the present chapter, results of a study to investigate the effects of loading rate and test temperature on the dynamic fracture initiation toughness in Gamma-Met PX are presented. Modified split Hopkinson pressure bar was used along with high-speed photography to determine the crack initiation time. Three-point bend dynamic fracture experiments were conducted at impact speeds of approx. 1 m/s and tests temperatures of up-to 1200 C. The results show that thc dynamic fracture initiation toughness decreases with increasing test temperatures beyond 600 C. Furthermore, thc effect of long time high temperature air exposure on the fracture toughness was investigated. The dynamic fracture initiation toughness was found to decrease with increasing exposure time. The reasons behind this drop are analyzed and discussed.

Testing of Confining Pressure Impacton Explosion Energy of Explosive Materials

NASA Astrophysics Data System (ADS)

Drzewiecki, Jan; Myszkowski, Jacek; Pytlik, Andrzej; Pytlik, Mateusz

2017-06-01

This paper presents the results of testing the explosion effects of two explosive charges placed in an environment with specified values of confining pressure. The aim of this study is to determine the impact of variable environmental conditions on the suitability of particular explosives for their use in the prevention of natural hazards in hard coal mining. The research results will contribute to improving the efficiency of currently adopted technologies of natural hazard prevention and aid in raising the level of occupational safety. To carry out the subject matter measurements, a special test stand was constructed which allows the value of the initial pressure inside the chamber, which constitutes its integral part, to be altered before the detonation of the charge being tested. The obtained characteristics of the pressure changes during the explosion of the analysed charge helped to identify the work (energy) which was produced during the process. The test results are a valuable source of information, opening up new possibilities for the use of explosives, the development of innovative solutions for the construction of explosive charges and their initiation.

The effects of initial testing on false recall and false recognition in the social contagion of memory paradigm.

PubMed

Huff, Mark J; Davis, Sara D; Meade, Michelle L

2013-08-01

In three experiments, participants studied photographs of common household scenes. Following study, participants completed a category-cued recall test without feedback (Exps. 1 and 3), a category-cued recall test with feedback (Exp. 2), or a filler task (no-test condition). Participants then viewed recall tests from fictitious previous participants that contained erroneous items presented either one or four times, and then completed final recall and source recognition tests. The participants in all conditions reported incorrect items during final testing (a social contagion effect), and across experiments, initial testing had no impact on false recall of erroneous items. However, on the final source-monitoring recognition test, initial testing had a protective effect against false source recognition: Participants who were initially tested with and without feedback on category-cued initial tests attributed fewer incorrect items to the original event on the final source-monitoring recognition test than did participants who were not initially tested. These data demonstrate that initial testing may protect individuals' memories from erroneous suggestions.

Sequential analysis as a tool for detection of amikacin ototoxicity in the treatment of multidrug-resistant tuberculosis.

PubMed

Vasconcelos, Karla Anacleto de; Frota, Silvana Maria Monte Coelho; Ruffino-Netto, Antonio; Kritski, Afrânio Lineu

2018-04-01

To investigate early detection of amikacin-induced ototoxicity in a population treated for multidrug-resistant tuberculosis (MDR-TB), by means of three different tests: pure-tone audiometry (PTA); high-frequency audiometry (HFA); and distortion-product otoacoustic emission (DPOAE) testing. This was a longitudinal prospective cohort study involving patients aged 18-69 years with a diagnosis of MDR-TB who had to receive amikacin for six months as part of their antituberculosis drug regimen for the first time. Hearing was assessed before treatment initiation and at two and six months after treatment initiation. Sequential statistics were used to analyze the results. We included 61 patients, but the final population consisted of 10 patients (7 men and 3 women) because of sequential analysis. Comparison of the test results obtained at two and six months after treatment initiation with those obtained at baseline revealed that HFA at two months and PTA at six months detected hearing threshold shifts consistent with ototoxicity. However, DPOAE testing did not detect such shifts. The statistical method used in this study makes it possible to conclude that, over the six-month period, amikacin-associated hearing threshold shifts were detected by HFA and PTA, and that DPOAE testing was not efficient in detecting such shifts.

46 CFR 56.97-38 - Initial service leak test (reproduces 137.7).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Initial service leak test (reproduces 137.7). 56.97-38... PIPING SYSTEMS AND APPURTENANCES Pressure Tests § 56.97-38 Initial service leak test (reproduces 137.7). (a) An initial service leak test and inspection is acceptable when other types of test are not...

Wind-tunnel development of an SR-71 aerospike rocket flight test configuration

NASA Technical Reports Server (NTRS)

Smith, Stephen C.; Shirakata, Norm; Moes, Timothy R.; Cobleigh, Brent R.; Conners, Timothy H.

1996-01-01

A flight experiment has been proposed to investigate the performance of an aerospike rocket motor installed in a lifting body configuration. An SR-71 airplane would be used to carry the aerospike configuration to the desired flight test conditions. Wind-tunnel tests were completed on a 4-percent scale SR-71 airplane with the aerospike pod mounted in various locations on the upper fuselage. Testing was accomplished using sting and blade mounts from Mach 0.6 to Mach 3.2. Initial test objectives included assessing transonic drag and supersonic lateral-directional stability and control. During these tests, flight simulations were run with wind-tunnel data to assess the acceptability of the configurations. Early testing demonstrated that the initial configuration with the aerospike pod near the SR-71 center of gravity was unsuitable because of large nosedown pitching moments at transonic speeds. The excessive trim drag resulting from accommodating this pitching moment far exceeded the excess thrust capability of the airplane. Wind-tunnel testing continued in an attempt to find a configuration suitable for flight test. Multiple configurations were tested. Results indicate that an aft-mounted model configuration possessed acceptable performance, stability, and control characteristics.

Output testing of small-arms primers

NASA Technical Reports Server (NTRS)

Bement, Laurence J.; Doris, Thomas A.; Schimmel, Morry L.

1991-01-01

The performance of two standard primers for initiating small-caliber ammunition are compared to that of a primer for initiating aircraft escape-system components. Three testing methods are employed including: (1) firing the primer to measure total energy delivered; (2) monitoring output in terms of gaseous product-mass flow rate and pressure as a function of time; and (3) firing the primer onto ignition material to study gas pressure produced during ignition and burning as a function of time. The results of the test demonstrate differences in the ignitability factors of the standard primers and time peak pressures of less than 100 microseconds. One unexpected result is that two percussion primers (the FA-41 and the M42C1) developed for different applications have the same ignitability. The ignitability test method is shown to yield the most useful data and can be used to specify percussion primers and optimize their performance.

TQM in a test environment

NASA Technical Reports Server (NTRS)

Chambers, Gary D.; King, Elizabeth A.; Oleson, Keith

1992-01-01

In response to the changing aerospace economic climate, Martin Marietta Astronautics Group (MMAG) has adopted a Total Quality Management (TQM) philosophy to maintain a competitive edge. TQM emphasizes continuous improvement of processes, motivation to improve from within, cross-functional involvement, people empowerment, customer satisfaction, and modern process control techniques. The four major initiatives of TQM are Product Excellence, Manufacturing Resource Planning (MRP II), People Empowerment, and Subcontract Management. The Defense Space and Communications (DS&C) Test Lab's definition and implementation of the MRP II and people empowerment initiatives within TQM are discussed. The application of MRP II to environmental test planning and operations processes required a new and innovative approach. In an 18 month span, the test labs implemented MRP II and people empowerment and achieved a Class 'A' operational status. This resulted in numerous benefits, both tangible and intangible, including significant cost savings and improved quality of life. A detailed description of the implementation process and results are addressed.

TQM in a test environment

NASA Astrophysics Data System (ADS)

Chambers, Gary D.; King, Elizabeth A.; Oleson, Keith

1992-11-01

In response to the changing aerospace economic climate, Martin Marietta Astronautics Group (MMAG) has adopted a Total Quality Management (TQM) philosophy to maintain a competitive edge. TQM emphasizes continuous improvement of processes, motivation to improve from within, cross-functional involvement, people empowerment, customer satisfaction, and modern process control techniques. The four major initiatives of TQM are Product Excellence, Manufacturing Resource Planning (MRP II), People Empowerment, and Subcontract Management. The Defense Space and Communications (DS&C) Test Lab's definition and implementation of the MRP II and people empowerment initiatives within TQM are discussed. The application of MRP II to environmental test planning and operations processes required a new and innovative approach. In an 18 month span, the test labs implemented MRP II and people empowerment and achieved a Class 'A' operational status. This resulted in numerous benefits, both tangible and intangible, including significant cost savings and improved quality of life. A detailed description of the implementation process and results are addressed.

Numerical simulation of Composition B high explosive charge desensitization in gap test assembly after loading by precursor wave

NASA Astrophysics Data System (ADS)

Balagansky, I. A.; Stepanov, A. A.

2016-03-01

Results of numerical research into the desensitization of high explosive charges in water gap test-based experimental assemblies are presented. The experimental data are discussed, and the analysis using ANSYS AUTODYN 14.5 is provided. The desensitization phenomenon is well reproduced in numerical simulation using the JWL EOS and the Lee-Tarver kinetic equation for modeling of the initiation of heterogeneous high explosives with as well as without shock front waves. The analysis of the wave processes occurring during the initiation of the acceptor HE charge has been carried out. Peculiarities of the wave processes in the water gap test assemblies, which can influence the results of sensitivity measurement, have been studied. In particular, it has been established that precursor waves in the walls of the gap test assemblies can influence the detonation transmission distance.

Prevailing Torque Locking Feature in Threaded Fasteners Using Anaerobic Adhesive

NASA Technical Reports Server (NTRS)

Hernandez, Alan; Hess, Daniel P.

2016-01-01

This paper presents results from tests to assess the use of anaerobic adhesive for providing a prevailing torque locking feature in threaded fasteners. Test procedures are developed and tests are performed on three fastener materials, four anaerobic adhesives, and both unseated assembly conditions. Five to ten samples are tested for each combination. Tests for initial use, reuse without additional adhesive, and reuse with additional adhesive are performed for all samples. A 48-hour cure time was used for all initial use and reuse tests. Test data are presented as removal torque versus removal angle with the specification required prevailing torque range added for performance assessment. Percent specification pass rates for the all combinations of fastener material, adhesive, and assembly condition are tabulated and reveal use of anaerobic adhesive as a prevailing torque locking feature is viable. Although not every possible fastener material and anaerobic adhesive combination provides prevailing torque values within specification, any combination can be assessed using the test procedures presented. Reuse without additional anaerobic adhesive generally provides some prevailing torque, and in some cases within specification. Reuse with additional adhesive often provides comparable removal torque data as in initial use.

The impact of repeat-testing of common chemistry analytes at critical concentrations.

PubMed

Onyenekwu, Chinelo P; Hudson, Careen L; Zemlin, Annalise E; Erasmus, Rajiv T

2014-12-01

Early notification of critical values by the clinical laboratory to the treating physician is a requirement for accreditation and is essential for effective patient management. Many laboratories automatically repeat a critical value before reporting it to prevent possible misdiagnosis. Given today's advanced instrumentation and quality assurance practices, we questioned the validity of this approach. We performed an audit of repeat-testing in our laboratory to assess for significant differences between initial and repeated test results, estimate the delay caused by repeat-testing and to quantify the cost of repeating these assays. A retrospective audit of repeat-tests for sodium, potassium, calcium and magnesium in the first quarter of 2013 at Tygerberg Academic Laboratory was conducted. Data on the initial and repeat-test values and the time that they were performed was extracted from our laboratory information system. The Clinical Laboratory Improvement Amendment criteria for allowable error were employed to assess for significant difference between results. A total of 2308 repeated tests were studied. There was no significant difference in 2291 (99.3%) of the samples. The average delay ranged from 35 min for magnesium to 42 min for sodium and calcium. At least 2.9% of laboratory running costs for the analytes was spent on repeating them. The practice of repeating a critical test result appears unnecessary as it yields similar results, delays notification to the treating clinician and increases laboratory running costs.

Creep Strain and Strain Rate Response of 2219 Al Alloy at High Stress Levels

NASA Technical Reports Server (NTRS)

Taminger, Karen M. B.; Wagner, John A.; Lisagor, W. Barry

1998-01-01

As a result of high localized plastic deformation experienced during proof testing in an International Space Station connecting module, a study was undertaken to determine the deformation response of a 2219-T851 roll forging. After prestraining 2219-T851 Al specimens to simulate strains observed during the proof testing, creep tests were conducted in the temperature range from ambient temperature to 107 C (225 F) at stress levels approaching the ultimate tensile strength of 2219-T851 Al. Strain-time histories and strain rate responses were examined. The strain rate response was extremely high initially, but decayed rapidly, spanning as much as five orders of magnitude during primary creep. Select specimens were subjected to incremental step loading and exhibited initial creep rates of similar magnitude for each load step. Although the creep rates decreased quickly at all loads, the creep rates dropped faster and reached lower strain rate levels for lower applied loads. The initial creep rate and creep rate decay associated with primary creep were similar for specimens with and without prestrain; however, prestraining (strain hardening) the specimens, as in the aforementioned proof test, resulted in significantly longer creep life.

Controller Evaluation of Initial Data Link Air Traffic Control Services: Mini Study 2 Volume II

DOT National Transportation Integrated Search

1989-03-01

This report details the results of Mini Study 2. This Mini Study was conducted at the Federal Aviation Administration (FAA) Technical Center utilizing the Data Link test bed. Initial Data Link air traffic control services were evaluated under part ta...

Controller Evaluation of Initial Data Link Air Traffic Control Services: Mini Study 2 Volume I

DOT National Transportation Integrated Search

1989-03-01

This report details the results of Mini Study 2. This Mini Study was conducted at the Federal Aviation Administration (FAA) Technical Center utilizing the Data Link test bed. Initial Data Link air traffic control services were evaluated under part ta...

LAPACK working note No. 10: Installing and testing the initial release of LAPACK Unix and non-Unix versions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, E.; Dongarra, J.

1989-05-01

This working note describes how to install and test the initial release of LAPACK. LAPACK is intended to provide a uniform set of subroutines to solve the most common linear algebra problems and to run efficiently on a wide range of architectures. The routines presented at this time are intended not for general distribution, but only for initial testing. We expect the testing to reveal weaknesses in the design, and we plan to modify routines to correct any deficiencies. The instructions for installing, testing, and timing are designed for a person whose responsibility is the maintenance of a mathematical softwaremore » library. This paper provides instructions for Unix users installing a tar tape, and contains instructions for non-Unix users. We assume the installer has experience in compiling and running Fortran programs and in creating object libraries. The installation process involves reading a tape, creating a library from the Fortran source, running the tests, and sending the results to Argonne. 6 refs.« less

Performance evaluation of DAAF as a booster material using the onionskin test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morris, John S; Francois, Elizabeth G; Hooks, Daniel E

Initiation of insensitive high explosive (IHE) formulations requires the use of a booster explosive in the initiation train. Booster material selection is crucial, as the initiation must reliably function across some spectrum of physical parameters. The interest in Diaminoazoxyfurazan (DAAF) for this application stems from the fact that it possesses many traits of an IHE but is shock sensitive enough to serve as an explosive booster. A hemispherical wave breakout test, termed the onionskin test, is one of the methods used to evaluate the performance of a booster material. The wave breakout time-position history at the surface of a hemisphericalmore » IHE charge is recorded and the relative uniformity of the breakout can be quantitatively compared between booster materials. A series of onionskin tests were performed to investigate breakout and propagation diaminoazoxyfurazan (DAAF) at low temperatures to evaluate ignition and detonation spreading in comparison to other explosives commonly used in booster applications. Some wave perturbation was observed with the DAAF booster in the onionskin tests presented. The results of these tests will be presented and discussed.« less

Mod-2 wind turbine project assessment and cluster test plans

NASA Technical Reports Server (NTRS)

Gordon, L. H.

1982-01-01

An assessment of the Mod-2 Wind Turbine project is presented based on initial goals and present results. Specifically, the Mod-2 background, project flow, and a chronology of events/results leading to Mod-2 acceptance is presented. After checkout/acceptance of the three operating turbines, NASA/LeRC will continue management of a two year test program performed at the DOE Goodnoe Hills test site. This test program is expected to yield data necessary for the continued development and optimization of wind energy systems. These test activities, the implementation of, and the results to date are also presented.

Fetal acoustic stimulation test for early intrapartum fetal monitoring.

PubMed

Goonewardene, M; Hanwellage, K

2011-03-01

The fetal acoustic stimulation test (FAST) is a simple cost effective screening test for antenatal fetal monitoring. The aim of the study was to evaluate the FAST as a screening test for early intrapartum fetal well being. An initial non stress test (NST) followed by a FAST using corometric model 146 was carried out in 486 participants in early labour with uncomplicated singleton pregnancies and > 32 weeks gestation. A repeat NST was recorded in the participants who had an initial non reactive NST. The results of the NST and FAST were compared with fetal outcome. Maternal perception of fetal movements after FAST, results of NST before and after FAST, and the babies' 5 minute APGAR scores were measured. Of the 486 participants 413 (85%) noticed fetal movements after FAST. Initial NST was non reactive in 203 (42%) but 149 (31%) became reactive after FAST. Compared to the NST, FAST had a better sensitivity (97% vs 62%, p < 0.001), specificity (100% vs 87%, p = 0.017), positive predictive value (100% vs 98%, p = 0.024), negative predictive value (79% vs 17%, p < 0.001) and accuracy (99%vs 64%, p < 0.001) in predicting 5 minute APGAR < 7 in the baby. FAST is a reliable screening test for assessing fetal well being in early labour. It complements the NST and is better than the NST alone.

Initial accomplishments of the Environmental Control and Life Support System (ECLSS) atmosphere revitalization (AR) predevelopment operational system test (POST) for the Space Station Freedom (SSF)

NASA Technical Reports Server (NTRS)

Dunn, Kevin H.; Bulgajewski, Peter J.

1992-01-01

Initial results of the integrated AR POST conducted by Boeing at Marshall Space Flight Center in 1992 are presented. The three baselined ECLSS Man Tended Capability AR assemblies were integrated and operated in a closed door chamber in which the internal atmosphere was monitored. The test provides a prerequisite checkout of the AR subsystem in preparation for longer duration tests in which the AR subsystem will be integrated with the Water Recovery Management subsystem. The integrated AR POST will serve as an early test bed to evaluate the integration of the space station ECLSS AR subsystem during design maturation.

EVALUATION OF A TEST METHOD FOR MEASURING INDOOR AIR EMISSIONS FROM DRY-PROCESS PHOTOCOPIERS

EPA Science Inventory

A large chamber test method for measuring indoor air emissions from office equipment was developed, evaluated, and revised based on the initial testing of four dry-process photocopiers. Because all chambers may not necessarily produce similar results (e.g., due to differences in ...

Hybrid Gear Preliminary Results-Application of Composites to Dynamic Mechanical Components

NASA Technical Reports Server (NTRS)

Handschuh, Robert F.; Roberts Gary D.; Sinnamon, R.; Stringer, David B.; Dykas, Brian D.; Kohlman, Lee W.

2012-01-01

Composite spur gears were fabricated and then tested at NASA Glenn Research Center. The composite material served as the web of the gear between the gear teeth and a metallic hub for mounting to the torque-applying shaft. The composite web was bonded only to the inner and outer hexagonal features that were machined from an initially all-metallic aerospace quality spur gear. The Hybrid Gear was tested against an all-steel gear and against a mating Hybrid Gear. As a result of the composite to metal fabrication process used, the concentricity of the gears were reduced from their initial high-precision value. Regardless of the concentricity error, the hybrid gears operated successfully for over 300 million cycles at 10000 rpm and 490 in.*lbs torque. Although the design was not optimized for weight, the composite gears were found to be 20% lighter than the all-steel gears. Free vibration modes and vibration/noise tests were also conduct to compare the vibration and damping characteristic of the Hybrid Gear to all-steel gears. The initial results indicate that this type of hybrid design may have a dramatic effect on drive system weight without sacrificing strength.

Evaluations of the conformational search accuracy of CAMDAS using experimental three-dimensional structures of protein-ligand complexes

NASA Astrophysics Data System (ADS)

Oda, A.; Yamaotsu, N.; Hirono, S.; Takano, Y.; Fukuyoshi, S.; Nakagaki, R.; Takahashi, O.

2013-08-01

CAMDAS is a conformational search program, through which high temperature molecular dynamics (MD) calculations are carried out. In this study, the conformational search ability of CAMDAS was evaluated using structurally known 281 protein-ligand complexes as a test set. For the test, the influences of initial settings and initial conformations on search results were validated. By using the CAMDAS program, reasonable conformations whose root mean square deviations (RMSDs) in comparison with crystal structures were less than 2.0 Å could be obtained from 96% of the test set even though the worst initial settings were used. The success rate was comparable to those of OMEGA, and the errors of CAMDAS were less than those of OMEGA. Based on the results obtained using CAMDAS, the worst RMSD was around 2.5 Å, although the worst value obtained was around 4.0 Å using OMEGA. The results indicated that CAMDAS is a robust and versatile conformational search method and that it can be used for a wide variety of small molecules. In addition, the accuracy of a conformational search in relation to this study was improved by longer MD calculations and multiple MD simulations.

Long life nickel electrodes for a nickel-hydrogen cell. I Initial performance

NASA Technical Reports Server (NTRS)

Lim, H. S.; Verzwyvelt, S. A.; Blaser, C.; Keener, K. M.

1983-01-01

In order to develop a long life nickel electrode for a Ni/H2 cell, an investigation was begun to study the effects of sinter structure and active material loading level on the long life performance of nickel electrodes. This paper is a report on the initial performance of these electrodes as a part of an accelerated life test program. Seven different types of nickel plaques were made which included three levels of both their mechanical strength and median pore size. These plaques were impregnated with three levels of active material loading. The resultant electrodes were tested by a 200-cycle stress test which was conducted in flooded electrolyte, and also for initial performance in a Ni/H2 boiler plate cell. An interesting and unexpected observation was that an increased initial utilization of the active material was due more to its complete discharge to the lower average oxidation state than its increased charge acceptance in the charged state.

PhoneSat: Ground Testing of a Phone-Based Prototype Bus

NASA Technical Reports Server (NTRS)

Felix, Carmen; Howard, Benjamin; Reyes, Matthew; Snarskiy, Fedor; Hickman, Ryan; Boshuizen, Christopher; Marshall, William

2010-01-01

Most of the key capabilities that are requisite of a satellite bus are housed in today's smart phones. PhoneSat refers to an initiative to build a ground-based prototype vehicle that could all the basic functionality of a satellite, including attitude control, using a smart Phone as its central hardware. All components used were also low cost Commercial off the Shelf (COTS). In summer 2009, an initial prototype was created using the LEGO Mindstorm toolkit demonstrating simple attitude control. Here we report on a follow up initiative to design, build and test a vehicle based on the Google s smart phone Nexus One. The report includes results from initial thermal-vacuum chamber tests and low altitude sub-orbital rocket flights which show that, at least for short durations, the Nexus One phone is able to withstand key aspects of the space environment without failure. We compare the sensor data from the Phone's accelerometers and magnetometers with that of an external microelectronic inertial measurement unit.

Infectious agent screening in canine blood donors in the United Kingdom.

PubMed

Crawford, K; Walton, J; Lewis, D; Tasker, S; Warman, S M

2013-08-01

Transfusion of blood products is an important component of veterinary emergency medicine. Donors must be carefully selected to minimise risk of transmission of blood-borne infectious agents. This study was devised to assess the prevalence of such agents in healthy, non-travelled UK dogs screened as prospective donors. Ethylenediaminetetraacetic acid blood samples from dogs donating blood between August 2007 and January 2012 were screened by polymerase chain reaction for haemotropic mycoplasmas, Bartonella, Babesia, Leishmania, Ehrlichia and Anaplasma spp. Dogs with positive or inconclusive results underwent repeat polymerase chain reaction testing. Four of 262 dogs had positive or inconclusive results at initial screening. Repeat polymerase chain reaction testing in each dog was negative, and none of the dogs developed clinical signs of disease. The positive results on initial screening may have represented false positives from sample contamination or amplification of non-target DNA. It is also possible that dogs were infected at initial sampling but successfully cleared infection before repeat testing. The low number of positive results obtained suggests that prevalence of these agents in a population of healthy UK dogs is low and that use of blood products is unlikely to represent a significant risk of transmission of these diseases. © 2013 British Small Animal Veterinary Association.

A 31-year-old man with bilateral blurry vision and floaters.

PubMed

Abazari, Azin; Kaplowitz, Kevin; Sibony, Patrick

2015-01-01

We report a case of bilateral multifocal retinochoroiditis and bilateral optic disc edema in a patient with cat-scratch disease from Bartonella henselae. The patient initially had negative serologic testing. Repeat testing showed a markedly increased IgG and IgM convalescent titer and the development of a branch retinal artery and vein occlusion. In patients for whom there is a high clinical suspicion of cat-scratch disease, a convalescent titer should be obtained 2-3 weeks following a negative initial result.

Effects of thickness on the aerodynamic characteristics of an initial low-speed family of airfoils for general aviation applications

NASA Technical Reports Server (NTRS)

Mcghee, R. J.; Beasley, W. D.

1976-01-01

Wind tunnel tests were conducted to determine the effects of airfoil thickness-ratio on the low speed aerodynamic characteristics of an initial family of airfoils. The results were compared with theoretical predictions obtained from a subsonic viscous method. The tests were conducted over a Mach number range from 0.10 to 0.28. Chord Reynolds numbers varied from about 2.0 x 1 million to 9.0 x 1 million.

Performance characteristics of a laser initiated microdetonator

NASA Technical Reports Server (NTRS)

Yang, L. C.

1981-01-01

The test results of 320 units of a laser initiated microdetonator are summarized. The commercially fabricated units used a lead styphnate/lead azide/HMX (1 mg/13.5 mg) explosive train design contained in a miniature aluminum can that was capped with a glass-metal seal window. The test parameters were the laser energy, temperature, laser pulse duration, laser wavelength and nuclear radiation (5,000,000 rad of 1 MeV gamma rays). The performance parameters were the laser energy for ignition and the actuation response time.

Playskin Lift: Development and Initial Testing of an Exoskeletal Garment to Assist Upper Extremity Mobility and Function

PubMed Central

Koshy, John; Hall, Martha L.; Erol, Ozan; Cao, Huantian; Buckley, Jenner M.; Galloway, James C.; Higginson, Jill

2016-01-01

Background A person's ability to move his or her arms against gravity is important for independent performance of critical activities of daily living and for exploration that facilitates early cognitive, language, social, and perceptual-motor development. Children with a variety of diagnoses have difficulty moving their arms against gravity. Objective The purpose of this technical report is to detail the design process and initial testing of a novel exoskeletal garment, the Playskin Lift, that assists and encourages children to lift their arms against gravity. Design This report details the design theory and process, the device, and the results of field testing with a toddler with impaired upper extremity function due to arthrogryposis multiplex congenita. Results The Playskin Lift is an inexpensive (<$30 material costs), easy to use (5/5 rating), comfortable (5/5 rating), and attractive (4/5 rating) device. While wearing the device, the child was able to contact objects more often throughout an increased play space, to look at toys more while contacting them, and to perform more complex interactions with toys. Limitations This report details initial testing with one child. Future testing with more participants is recommended. Conclusions These results suggest that by considering the broad needs of users, including cost, accessibility, comfort, aesthetics, and function, we can design inexpensive devices that families and clinicians can potentially fabricate in their own communities to improve function, participation, exploration, and learning for children with disabilities. PMID:26316534

Divided attention improves delayed, but not immediate retrieval of a consolidated memory.

PubMed

Kessler, Yoav; Vandermorris, Susan; Gopie, Nigel; Daros, Alexander; Winocur, Gordon; Moscovitch, Morris

2014-01-01

A well-documented dissociation between memory encoding and retrieval concerns the role of attention in the two processes. The typical finding is that divided attention (DA) during encoding impairs future memory, but retrieval is relatively robust to attentional manipulations. However, memory research in the past 20 years had demonstrated that retrieval is a memory-changing process, in which the strength and availability of information are modified by various characteristics of the retrieval process. Based on this logic, several studies examined the effects of DA during retrieval (Test 1) on a future memory test (Test 2). These studies yielded inconsistent results. The present study examined the role of memory consolidation in accounting for the after-effect of DA during retrieval. Initial learning required a classification of visual stimuli, and hence involved incidental learning. Test 1 was administered 24 hours after initial learning, and therefore required retrieval of consolidated information. Test 2 was administered either immediately following Test 1 or after a 24-hour delay. Our results show that the effect of DA on Test 2 depended on this delay. DA during Test 1 did not affect performance on Test 2 when it was administered immediately, but improved performance when Test 2 was given 24-hours later. The results are consistent with other findings showing long-term benefits of retrieval difficulty. Implications for theories of reconsolidation in human episodic memory are discussed.

The value of confirmatory testing in early infant HIV diagnosis programmes in South Africa: A cost-effectiveness analysis.

PubMed

Dunning, Lorna; Francke, Jordan A; Mallampati, Divya; MacLean, Rachel L; Penazzato, Martina; Hou, Taige; Myer, Landon; Abrams, Elaine J; Walensky, Rochelle P; Leroy, Valériane; Freedberg, Kenneth A; Ciaranello, Andrea

2017-11-01

The specificity of nucleic acid amplification tests (NAATs) used for early infant diagnosis (EID) of HIV infection is <100%, leading some HIV-uninfected infants to be incorrectly identified as HIV-infected. The World Health Organization recommends that infants undergo a second NAAT to confirm any positive test result, but implementation is limited. Our objective was to determine the impact and cost-effectiveness of confirmatory HIV testing for EID programmes in South Africa. Using the Cost-effectiveness of Preventing AIDS Complications (CEPAC)-Pediatric model, we simulated EID testing at age 6 weeks for HIV-exposed infants without and with confirmatory testing. We assumed a NAAT cost of US$25, NAAT specificity of 99.6%, NAAT sensitivity of 100% for infants infected in pregnancy or at least 4 weeks prior to testing, and a mother-to-child transmission (MTCT) rate at 12 months of 4.9%; we simulated guideline-concordant rates of testing uptake, result return, and antiretroviral therapy (ART) initiation (100%). After diagnosis, infants were linked to and retained in care for 10 years (false-positive) or lifelong (true-positive). All parameters were varied widely in sensitivity analyses. Outcomes included number of infants with false-positive diagnoses linked to ART per 1,000 ART initiations, life expectancy (LE, in years) and per-person lifetime HIV-related healthcare costs. Both without and with confirmatory testing, LE was 26.2 years for HIV-infected infants and 61.4 years for all HIV-exposed infants; clinical outcomes for truly infected infants did not differ by strategy. Without confirmatory testing, 128/1,000 ART initiations were false-positive diagnoses; with confirmatory testing, 1/1,000 ART initiations were false-positive diagnoses. Because confirmatory testing averted costly HIV care and ART in truly HIV-uninfected infants, it was cost-saving: total cost US$1,790/infant tested, compared to US$1,830/infant tested without confirmatory testing. Confirmatory testing remained cost-saving unless NAAT cost exceeded US$400 or the HIV-uninfected status of infants incorrectly identified as infected was ascertained and ART stopped within 3 months of starting. Limitations include uncertainty in the data used in the model, which we examined with sensitivity and uncertainty analyses. We also excluded clinical harms to HIV-uninfected infants incorrectly treated with ART after false-positive diagnosis (e.g., medication toxicities); including these outcomes would further increase the value of confirmatory testing. Without confirmatory testing, in settings with MTCT rates similar to that of South Africa, more than 10% of infants who initiate ART may reflect false-positive diagnoses. Confirmatory testing prevents inappropriate HIV diagnosis, is cost-saving, and should be adopted in all EID programmes.

Effect of a Laptop Initiative on Middle School Mathematics Achievement

ERIC Educational Resources Information Center

Lambert, Edna Earl White

2014-01-01

In the wake of No Child Left Behind, schools continue to be evaluated according to standardized test results. Researchers suggest that technology can assist students with development and school achievement. While laptop initiative (LI) technology was being implemented by South Carolina districts in the middle schools classrooms, educational…

49 CFR 178.70 - Approval of UN pressure receptacles.

Code of Federal Regulations, 2012 CFR

2012-10-01

... designee. (b) IIA pre-audit. The manufacturer must submit an application for initial design type approval... of the manufacturer and the IIA certifying the design type, the test results, chemical analyses, lot... initial design type approval. If the pre-audit is found satisfactory by the IIA, the manufacturer will...

49 CFR 178.70 - Approval of UN pressure receptacles.

Code of Federal Regulations, 2011 CFR

2011-10-01

... designee. (b) IIA pre-audit. The manufacturer must submit an application for initial design type approval... of the manufacturer and the IIA certifying the design type, the test results, chemical analyses, lot... initial design type approval. If the pre-audit is found satisfactory by the IIA, the manufacturer will...

49 CFR 178.70 - Approval of UN pressure receptacles.

Code of Federal Regulations, 2014 CFR

2014-10-01

... designee. (b) IIA pre-audit. The manufacturer must submit an application for initial design type approval... of the manufacturer and the IIA certifying the design type, the test results, chemical analyses, lot... initial design type approval. If the pre-audit is found satisfactory by the IIA, the manufacturer will...

49 CFR 178.70 - Approval of UN pressure receptacles.

Code of Federal Regulations, 2013 CFR

2013-10-01

... designee. (b) IIA pre-audit. The manufacturer must submit an application for initial design type approval... of the manufacturer and the IIA certifying the design type, the test results, chemical analyses, lot... initial design type approval. If the pre-audit is found satisfactory by the IIA, the manufacturer will...

Occulting focal plane masks for Terrestrial Planet Finder Coronagraph: design, fabrication, simulations and test results

NASA Technical Reports Server (NTRS)

Balasubramanian, Kunjithapatham; Hoppe, Daniel J.; Halverson, Peter G.; Wilson, Daniel W.; Echternach, Pierre M.; Shi, Fang; Lowman, Andrew E.; Niessner, Albert F.; Trauger, John T.; Shaklan, Stuart B.

2005-01-01

Occulting focal plane masks for the Terrestrial Planet Finder Coronagraph (TPF-C) could be designed with continuous gray scale profile of the occulting pattern such as 1-sinc2 on a suitable material or with micron-scale binary transparent and opaque structures of metallic pattern on glass. We have designed, fabricated and tested both kinds of masks. The fundamental characteristics of such masks and initial test results from the High Contrast Imaging Test bed (HCIT) at JPL are presented.

A cold ejector for closed-cycle helium refrigerators

NASA Technical Reports Server (NTRS)

Johnson, D. L.; Daggett, D. L.

1987-01-01

The test results are presented of an initial cold helium ejector design that can be installed on a closed cycle refrigerator to provide refrigeration at temperatures below 4.2 K. The ejector, test apparatus, instrumentation, and test results are described. Tests were conducted both at room temperature and at cryogenic temperatures to provide operational experience with the ejector as well as for future use in the subsequent design of an ejector that will provide refrigeration at temperatures below 3 K.

USNO GPS program

NASA Technical Reports Server (NTRS)

Putkovich, K.

1981-01-01

Initial test results indicated that the Global Positioning System/Time Transfer Unit (GPS/TTU) performed well within the + or - 100 nanosecond range required by the original system specification. Subsequent testing involved the verification of GPS time at the master control site via portable clocks and the acquisition and tracking of as many passes of the space vehicles currently in operation as possible. A description and discussion of the testing, system modifications, test results obtained, and an evaluation of both GPS and the GPS/TTU are presented.

Initial retrieval shields against retrieval-induced forgetting.

PubMed

Racsmány, Mihály; Keresztes, Attila

2015-01-01

Testing, as a form of retrieval, can enhance learning but it can also induce forgetting of related memories, a phenomenon known as retrieval-induced forgetting (RIF). In four experiments we explored whether selective retrieval and selective restudy of target memories induce forgetting of related memories with or without initial retrieval of the entire learning set. In Experiment 1, subjects studied category-exemplar associations, some of which were then either restudied or retrieved. RIF occurred on a delayed final test only when memories were retrieved and not when they were restudied. In Experiment 2, following the study phase of category-exemplar associations, subjects attempted to recall all category-exemplar associations, then they selectively retrieved or restudied some of the exemplars. We found that, despite the huge impact on practiced items, selective retrieval/restudy caused no decrease in final recall of related items. In Experiment 3, we replicated the main result of Experiment 2 by manipulating initial retrieval as a within-subject variable. In Experiment 4 we replicated the main results of the previous experiments with non-practiced (Nrp) baseline items. These findings suggest that initial retrieval of the learning set shields against the forgetting effect of later selective retrieval. Together, our results support the context shift theory of RIF.

Cost-effectiveness of alternative test strategies for the diagnosis of coronary artery disease.

PubMed

Garber, A M; Solomon, N A

1999-05-04

The appropriate roles for several diagnostic tests for coronary disease are uncertain. To evaluate the cost-effectiveness of alternative approaches to diagnosis of coronary disease. Meta-analysis of the accuracy of alternative diagnostic tests plus decision analysis to assess the health outcomes and costs of alternative diagnostic strategies for patients at intermediate pretest risk for coronary disease. Studies of test accuracy that met inclusion criteria; published information on treatment effectiveness and disease prevalence. Men and women 45, 55, and 65 years of age with a 25% to 75% pretest risk for coronary disease. 30 years. Societal. Diagnostic strategies were initial angiography and initial testing with one of five noninvasive tests--exercise treadmill testing, planar thallium imaging, single-photon emission computed tomography (SPECT), stress echocardiography, and positron emission tomography (PET)--followed by coronary angiography if noninvasive test results were positive. Testing was followed by observation, medical treatment, or revascularization. Life-years, quality-adjusted life-years (QALYs), costs, and costs per QALY. Life expectancy varied little with the initial diagnostic test; for a 55-year-old man, the best-performing test increased life expectancy by 7 more days than the worst-performing test. More sensitive tests increased QALYs more. Echocardiography improved health outcomes and reduced costs relative to stress testing and planar thallium imaging. The incremental cost-effectiveness ratio was $75,000/QALY for SPECT relative to echocardiography and was greater than $640,000 for PET relative to SPECT. Compared with SPECT, immediate angiography had an incremental cost-effectiveness ratio of $94,000/QALY. Qualitative findings varied little with age, sex, pretest probability of disease, or the test indeterminancy rate. Results varied most with sensitivity to severe coronary disease. Echocardiography, SPECT, and immediate angiography are cost-effective alternatives to PET and other diagnostic approaches. Test selection should reflect local variation in test accuracy.

Neutron Imaging for Selective Laser Melting Inconel Hardware with Internal Passages

NASA Technical Reports Server (NTRS)

Tramel, Terri L.; Norwood, Joseph K.; Bilheux, Hassina

2014-01-01

Additive Manufacturing is showing great promise for the development of new innovative designs and large potential life cycle cost reduction for the Aerospace Industry. However, more development work is required to move this technology into space flight hardware production. With selective laser melting (SLM), hardware that once consisted of multiple, carefully machined and inspected pieces, joined together can be made in one part. However standard inspection techniques cannot be used to verify that the internal passages are within dimensional tolerances or surface finish requirements. NASA/MSFC traveled to Oak Ridge National Lab's (ORNL) Spallation Neutron Source to perform some non-destructive, proof of concept imaging measurements to assess the capabilities to understand internal dimensional tolerances and internal passages surface roughness. This presentation will describe 1) the goals of this proof of concept testing, 2) the lessons learned when designing and building these Inconel 718 test specimens to minimize beam time, 3) the neutron imaging test setup and test procedure to get the images, 4) the initial results in images, volume and a video, 4) the assessment of using this imaging technique to gather real data for designing internal flow passages in SLM manufacturing aerospace hardware, and lastly 5) how proper cleaning of the internal passages is critically important. In summary, the initial results are very promising and continued development of a technique to assist in SLM development for aerospace components is desired by both NASA and ORNL. A plan forward that benefits both ORNL and NASA will also be presented, based on the promising initial results. The initial images and volume reconstruction showed that clean, clear images of the internal passages geometry are obtainable. These clear images of the internal passages of simple geometries will be compared to the build model to determine any differences. One surprising result was that a new cleaning process was used on these simply geometric specimens that resulted in what appears to be very smooth internal surfaces, when compared to other aerospace hardware cleaning methods.

HAL/S-360 compiler test activity report

NASA Technical Reports Server (NTRS)

Helmers, C. T.

1974-01-01

The levels of testing employed in verifying the HAL/S-360 compiler were as follows: (1) typical applications program case testing; (2) functional testing of the compiler system and its generated code; and (3) machine oriented testing of compiler implementation on operational computers. Details of the initial test plan and subsequent adaptation are reported, along with complete test results for each phase which examined the production of object codes for every possible source statement.

Experimental Model of Biofilm Implant-Related Osteomyelitis To Test Combination Biomaterials Using Biofilms as Initial Inocula

PubMed Central

Williams, Dustin L.; Haymond, Bryan S.; Woodbury, Kassie L.; Beck, J. Peter; Moore, David E.; Epperson, R. Tyler; Bloebaum, Roy D.

2012-01-01

Currently, the majority of animal models that are used to study biofilm-related infections utilize planktonic bacterial cells as initial inocula to produce positive signals of infection in biomaterials studies. However, the use of planktonic cells has potentially led to inconsistent results in infection outcomes. In this study, well-established biofilms of methicillin-resistant Staphylococcus aureus (MRSA) were grown and used as initial inocula in an animal model of a Type IIIB open fracture. The goal of the work was to establish, for the first time, a repeatable model of biofilm implant-related osteomyelitis wherein biofilms were used as initial inocula to test combination biomaterials. Results showed that 100% of animals that were treated with biofilms developed osteomyelitis, whereas 0% of animals not treated with biofilm developed infection. The development of this experimental model may lead to an important shift in biofilm and biomaterials research by showing that when biofilms are used as initial inocula, they may provide additional insights into how biofilm-related infections in the clinic develop and how they can be treated with combination biomaterials to eradicate and/or prevent biofilm formation. PMID:22492534

Experimental model of biofilm implant-related osteomyelitis to test combination biomaterials using biofilms as initial inocula.

PubMed

Williams, Dustin L; Haymond, Bryan S; Woodbury, Kassie L; Beck, J Peter; Moore, David E; Epperson, R Tyler; Bloebaum, Roy D

2012-07-01

Currently, the majority of animal models that are used to study biofilm-related infections use planktonic bacterial cells as initial inocula to produce positive signals of infection in biomaterials studies. However, the use of planktonic cells has potentially led to inconsistent results in infection outcomes. In this study, well-established biofilms of methicillin-resistant Staphylococcus aureus were grown and used as initial inocula in an animal model of a Type IIIB open fracture. The goal of the work was to establish, for the first time, a repeatable model of biofilm implant-related osteomyelitis, wherein biofilms were used as initial inocula to test combination biomaterials. Results showed that 100% of animals that were treated with biofilms developed osteomyelitis, whereas 0% of animals not treated with biofilm developed infection. The development of this experimental model may lead to an important shift in biofilm and biomaterials research by showing that when biofilms are used as initial inocula, they may provide additional insights into how biofilm-related infections in the clinic develop and how they can be treated with combination biomaterials to eradicate and/or prevent biofilm formation. Copyright © 2012 Wiley Periodicals, Inc.

False-positive cerebrospinal fluid cryptococcus antigen in Libman-Sacks endocarditis.

PubMed

Isseh, Iyad N; Bourgi, Kassem; Nakhle, Asaad; Ali, Mahmoud; Zervos, Marcus J

2016-12-01

Cryptococcus meningoencephalitis is a serious opportunistic infection associated with high morbidity and mortality in immunocompromised hosts, particularly patients with advanced AIDS disease. The diagnosis is established through cerebrospinal fluid (CSF) cryptococcus antigen detection and cultures. Cryptococcus antigen testing is usually the initial test of choice due its high sensitivity and specificity along with the quick availability of the results. We hereby report a case of a false-positive CSF cryptococcus antigen assay in a patient with systemic lupus erythematosus presenting with acute confusion. While initial CSF evaluation revealed a positive cryptococcus antigen assay, the patient's symptoms were inconsistent with cryptococcus meningoencephalitis. A repeat CSF evaluation, done 3 days later, revealed a negative CSF cryptococcus antigen assay. Given the patient's active lupus disease and the elevated antinuclear antibody titers, we believe that the initial positive result was a false positive caused by interference from autoantibodies.

A combination SMS and transportation reimbursement intervention to improve HIV care following abnormal CD4 test results in rural Uganda: a prospective observational cohort study.

PubMed

Siedner, Mark J; Santorino, Data; Lankowski, Alexander J; Kanyesigye, Michael; Bwana, Mwebesa B; Haberer, Jessica E; Bangsberg, David R

2015-07-06

Up to 50 % of HIV-infected persons in sub-Saharan Africa are lost from care between HIV diagnosis and antiretroviral therapy (ART) initiation. Structural barriers, including cost of transportation to clinic and poor communication systems, are major contributors. We conducted a prospective, pragmatic, before-and-after clinical trial to evaluate a combination mobile health and transportation reimbursement intervention to improve care at a publicly operated HIV clinic in Uganda. Patients undergoing CD4 count testing were enrolled, and clinicians selected a result threshold that would prompt early return for ART initiation or further care. Participants enrolled in the pre-intervention period (January - August 2012) served as a control group. Participants in the intervention period (September 2012 - November 2013) were randomized to receive daily short message service (SMS) messages for up to seven days in one of three formats: 1) messages reporting an abnormal result directly, 2) personal identification number-protected messages reporting an abnormal result, or 3) messages reading "ABCDEFG" to confidentially convey an abnormal result. Participants returning within seven days of their first message received transportation reimbursements (about $6USD). Our primary outcomes of interest were time to return to clinic and time to ART initiation. There were 45 participants in the pre-intervention period and 138 participants in the intervention period (46, 49, and 43 in the direct, PIN, and coded groups, respectively) with low CD4 count results. Median time to clinic return was 33 days (IQR 11-49) in the pre-intervention period and 6 days (IQR 3-16) in the intervention period (P < 0.001); and median time to ART initiation was 47 days (IQR 11-75) versus 12 days (IQR 5-19), (P < 0.001). In multivariable models, participants in the intervention period had earlier return to clinic (AHR 2.32, 95 %CI 1.53 to 3.51) and earlier time to ART initiation (AHR 2.27, 95 %CI 1.38 to 3.72). All three randomized message formats improved time to return to clinic and time to ART initiation (P < 0.01 for all comparisons versus the pre-intervention period). A combination of an SMS laboratory result communication system and transportation reimbursements significantly decreased time to clinic return and time to ART initiation after abnormal CD4 test results. Clinicaltrials.gov NCT01579214 , approved 13 April 2012.

Initial Comparison of Single Cylinder Stirling Engine Computer Model Predictions with Test Results

NASA Technical Reports Server (NTRS)

Tew, R. C., Jr.; Thieme, L. G.; Miao, D.

1979-01-01

A Stirling engine digital computer model developed at NASA Lewis Research Center was configured to predict the performance of the GPU-3 single-cylinder rhombic drive engine. Revisions to the basic equations and assumptions are discussed. Model predictions with the early results of the Lewis Research Center GPU-3 tests are compared.

Development of first generation aerospace NiMH cells

NASA Technical Reports Server (NTRS)

Tinker, Lawrence; Dell, Dan; Wu, Tony; Rampel, Guy

1993-01-01

Gates Aerospace Batteries in conjunction with Gates Energy Products (GEP) has been developing NiMH technology for aerospace use since 1990. GEP undertook the development of NiMH technology for commercial cell applications in 1987. This program focused on wound cell technology for replacement of current NiCd technology. As an off shoot of this program small, wound cells were used to evaluate initial design options for aerospace prismatic cell designs. Early in 1991, the first aerospace prismatic cell designs were built in a 6 Ah cell configuration. These cells were used to initially characterize performance in prismatic configurations and begin early life cycle testing. Soon after the 6 Ah cells were on test, several 22 Ah cells were built to test other options. The results of testing of these cells were used to identify potential problem areas for long lived cells and develop solutions to those problems. Following these two cell builds, a set of 7 Ah cells was built to evaluate improvements to the technology. To date results from these tests are very promising. Cycle lives in excess of 2,200 LEO cycles at 50 percent DoD were achieved with cells continuing on test. Results from these cell tests are discussed and data presented to demonstrate feasibility of this technology for aerospace programs.

77 FR 73056 - Initial Test Programs for Water-Cooled Nuclear Power Plants

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-07

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0293] Initial Test Programs for Water-Cooled Nuclear Power... (DG), DG-1259, ``Initial Test Programs for Water-Cooled Nuclear Power Plants.'' This guide describes the general scope and depth that the staff of the NRC considers acceptable for Initial Test Programs...

77 FR 36014 - Initial Test Program of Emergency Core Cooling Systems for Boiling-Water Reactors

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-15

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0134] Initial Test Program of Emergency Core Cooling... for public comment draft regulatory guide (DG), DG-1277, ``Initial Test Program of Emergency Core... acceptable to implement with regard to initial testing features of emergency core cooling systems (ECCSs) for...

Evaluation of the intelligent cruise control system : volume 1 : study results

DOT National Transportation Integrated Search

1999-10-01

The Intelligent Cruise Control (ICC) system evaluation was based on an ICC Field Operational Test (FOT) performed in Michigan. The FOT involved 108 volunteers recruited to drive ten ICC-equipped Chrysler Concordes. Testing was initiated in July 1996 ...

Sidewalk undermining studies : phase III, field and model studies.

DOT National Transportation Integrated Search

1979-01-01

The results of the early studies of the undermining problems are summarized in the initial portion of this report. Additionally, the design and use of a model sidewalk for testing procedures for preventing undermining are described. Based upon tests ...

49 CFR 40.3 - What do the terms used in this part mean?

Code of Federal Regulations, 2010 CFR

2010-10-01

... one that requires further testing for drugs or drug metabolites. Initial specimen validity test. The... specimen. A specimen that has been altered, as evidenced by test results showing either a substance that is... endogenous substance. Affiliate. Persons are affiliates of one another if, directly or indirectly, one...

Geothermal Energy Geopressure Subprogram: DOE Lafourche Crossing No. 1, Terrebonne Parish and Lafourche Parish, Louisiana: Environmental assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1978-10-01

The proposed action will consist of drilling one geothermal fluid well for intermittent production testing of 284 days over a three year period. Two disposal wells will initially be drilled to provide disposal of lower volume fluids produced during initial testing. Two additional disposal wells will be drilled, logged, completed, tested, and operated prior to commencement of high volume fluid production. Construction of the proposed action will change the land-use of 2 ha (5 ac) for the test well and each of the injection wells from agriculture or wetlands to resource exploration. Lands will be cleared and erosion and runoffmore » will result. During operation of the well test, the only expected impacts are from venting of gases or flaring of gases and noise. After the tests are completed, the area will be restored as much as possible to its natural condition by revegetation programs using nature species. All sources of pollutants will be collected and disposed in environmentally acceptable ways. Accidents may result from this proposed action.« less

A Comment on Early Student Blunders on Computer-Based Adaptive Tests

ERIC Educational Resources Information Center

Green, Bert F.

2011-01-01

This article refutes a recent claim that computer-based tests produce biased scores for very proficient test takers who make mistakes on one or two initial items and that the "bias" can be reduced by using a four-parameter IRT model. Because the same effect occurs with pattern scores on nonadaptive tests, the effect results from IRT scoring, not…

Initial Closed Operation of the CELSS Test Facility Engineering Development Unit

NASA Technical Reports Server (NTRS)

Kliss, Mark

1995-01-01

As part of the NASA Controlled Ecological Life Support System (CELSS) Program, a CELSS Test Facility (CTF) is being planned for installation on the Space Station. The CTF will be used to provide data on the productivity and efficiency of a variety of CELSS higher plant crops grown sequentially from seed to harvest in the microgravity environment of the Space Station. Stringent environmental control will be maintained while fundamental crop productivity issues, such as carbon dioxide uptake and oxygen production rates, water transpiration rates, and biomass accumulation rates are obtained for comparison with ground-based data. In order to obtain an early realistic determination of the subsystem and system requirements necessary to provide the appropriate environmental conditions specified for CTF crop productivity experiments, an Engineering Development Unit (EDU) has been constructed and is undergoing initial operational testing at NASA Ames Research Center. The EDU is a ground-based testbed which will be used to characterize the integrated performance of major subsystem technologies, to evaluate hardware candidates and control strategies required for the CTF, and to further define the ability to meet CTF requirements within present Space Station constraints. This paper describes the initial closed operational testing of the EDU. Measured performance data are compared with the specified functional requirements and results from initial closed testing are presented. Plans for future science and technology testing are discussed.

Two pseudo-outbreaks of infectious mononucleosis.

PubMed

Armstrong, C W; Hackler, R L; Miller, G B

1986-01-01

Two outbreaks of suspected infectious mononucleosis (IM) were investigated. In the first outbreak IM was diagnosed in nine children attending a day care center. They had been tested in physicians' offices for heterophile antibody using rapid differential slide tests; all tests had been reported positive. On retesting, none of the suspected cases had detectable serum heterophile antibody. The initial test results had been falsely positive as a result of poor laboratory technique. In the second outbreak IM had been diagnosed in 285 college students. Suspected cases had been found to have serum IgG antibody to the viral capsid antigen of Epstein-Barr virus, but most had not been tested for the presence of heterophile antibody. Retesting of 64 students within 1 month of initial testing yielded only one with heterophile antibody. With the exception of young children (less than 4 years of age), differential slide tests for heterophile antibody are sensitive and specific for recent Epstein-Barr virus infection if properly performed. Viral capsid antigen to Epstein-Barr virus (IgG) titers are of limited usefulness in diagnosing acute IM. The misdiagnosis of IM can be prevented by the appropriate selection, performance and interpretation of diagnostic laboratory tests.

Estimating the Impact of Earlier ART Initiation and Increased Testing Coverage on HIV Transmission among Men Who Have Sex with Men in Mexico using a Mathematical Model.

PubMed

Caro-Vega, Yanink; del Rio, Carlos; Lima, Viviane Dias; Lopez-Cervantes, Malaquias; Crabtree-Ramirez, Brenda; Bautista-Arredondo, Sergio; Colchero, M Arantxa; Sierra-Madero, Juan

2015-01-01

To estimate the impact of late ART initiation on HIV transmission among men who have sex with men (MSM) in Mexico. An HIV transmission model was built to estimate the number of infections transmitted by HIV-infected men who have sex with men (MSM-HIV+) MSM-HIV+ in the short and long term. Sexual risk behavior data were estimated from a nationwide study of MSM. CD4+ counts at ART initiation from a representative national cohort were used to estimate time since infection. Number of MSM-HIV+ on treatment and suppressed were estimated from surveillance and government reports. Status quo scenario (SQ), and scenarios of early ART initiation and increased HIV testing were modeled. We estimated 14239 new HIV infections per year from MSM-HIV+ in Mexico. In SQ, MSM take an average 7.4 years since infection to initiate treatment with a median CD4+ count of 148 cells/mm3(25th-75th percentiles 52-266). In SQ, 68% of MSM-HIV+ are not aware of their HIV status and transmit 78% of new infections. Increasing the CD4+ count at ART initiation to 350 cells/mm3 shortened the time since infection to 2.8 years. Increasing HIV testing to cover 80% of undiagnosed MSM resulted in a reduction of 70% in new infections in 20 years. Initiating ART at 500 cells/mm3 and increasing HIV testing the reduction would be of 75% in 20 years. A substantial number of new HIV infections in Mexico are transmitted by undiagnosed and untreated MSM-HIV+. An aggressive increase in HIV testing coverage and initiating ART at a CD4 count of 500 cells/mm3 in this population would significantly benefit individuals and decrease the number of new HIV infections in Mexico.

Histoplasma Urinary Antigen Testing Obviates the Need for Coincident Serum Antigen Testing.

PubMed

Libert, Diane; Procop, Gary W; Ansari, Mohammad Q

2018-03-07

Serum and urine antigen (SAg, UAg) detection are common tests for Histoplasma capsulatum. UAg detection is more widely used and reportedly has a higher sensitivity. We investigated whether SAg detection contributes meaningfully to the initial evaluation of patients with suspected histoplasmosis. We reviewed 20,285 UAg and 1,426 SAg tests ordered from 1997 to 2016 and analyzed paired UAg and SAg tests completed on the same patient within 1 week. We determined the positivity rate for each test. Of 601 paired specimens, 542 were concurrent negatives and 48 were concurrent positives (98% agreement). Medical records were available for eight of 11 pairs with discrepant results. UAg was falsely positive in six instances, truly positive once, and falsely negative once. These findings support using a single antigen detection test, rather than both UAg and SAg, as an initial screen for suspected histoplasmosis. This aligns with the current practice of most physicians.

Citizen Science: The Small World Initiative Improved Lecture Grades and California Critical Thinking Skills Test Scores of Nonscience Major Students at Florida Atlantic University.

PubMed

Caruso, Joseph P; Israel, Natalie; Rowland, Kimberly; Lovelace, Matthew J; Saunders, Mary Jane

2016-03-01

Course-based undergraduate research is known to improve science, technology, engineering, and mathematics student achievement. We tested "The Small World Initiative, a Citizen-Science Project to Crowdsource Novel Antibiotic Discovery" to see if it also improved student performance and the critical thinking of non-science majors in Introductory Biology at Florida Atlantic University (a large, public, minority-dominant institution) in academic year 2014-15. California Critical Thinking Skills Test pre- and posttests were offered to both Small World Initiative (SWI) and control lab students for formative amounts of extra credit. SWI lab students earned significantly higher lecture grades than control lab students, had significantly fewer lecture grades of D+ or lower, and had significantly higher critical thinking posttest total scores than control students. Lastly, more SWI students were engaged while taking critical thinking tests. These results support the hypothesis that utilizing independent course-based undergraduate science research improves student achievement even in nonscience students.

How to test for partially predictable chaos.

PubMed

Wernecke, Hendrik; Sándor, Bulcsú; Gros, Claudius

2017-04-24

For a chaotic system pairs of initially close-by trajectories become eventually fully uncorrelated on the attracting set. This process of decorrelation can split into an initial exponential decrease and a subsequent diffusive process on the chaotic attractor causing the final loss of predictability. Both processes can be either of the same or of very different time scales. In the latter case the two trajectories linger within a finite but small distance (with respect to the overall extent of the attractor) for exceedingly long times and remain partially predictable. Standard tests for chaos widely use inter-orbital correlations as an indicator. However, testing partially predictable chaos yields mostly ambiguous results, as this type of chaos is characterized by attractors of fractally broadened braids. For a resolution we introduce a novel 0-1 indicator for chaos based on the cross-distance scaling of pairs of initially close trajectories. This test robustly discriminates chaos, including partially predictable chaos, from laminar flow. Additionally using the finite time cross-correlation of pairs of initially close trajectories, we are able to identify laminar flow as well as strong and partially predictable chaos in a 0-1 manner solely from the properties of pairs of trajectories.

Microstructural examination of fatigue crack tip in high strength steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fukuoka, C.; Yoshizawa, H.; Nakagawa, Y.G.

1993-10-01

Fatigue tests were performed to examine how microstructural conditioning influences crack initiation and propagation in SA508 class 3 low-carbon steel. A 3-mm-long crack was introduced in compact tension (CT) fatigue test specimens under four different loads in order to obtain crack tip plastic zones at different stress intensity factor ranges, [Delta]K = 18, 36, 54, and 72 MPa[radical]m. The microstructure of the plastic zones around the crack tip were examined by transmission electron microscopy (TEM) and selected area electron diffraction (SAD). Micro-orientation of the dislocation cells in the plastic zones of all of the CT samples increased to 4 degmore » from the level of an as-received sample. Four-point bending fatigue tests were performed for plate shape samples with a large cyclic strain range. The SAD value of the bending samples was also 4 deg in the damaged area where cracks already initiated at an early stage of the fatigue process. These test results indicate that the microstructural conditioning is a prerequisite for the fatigue crack initiation and propagation in SA508. These observations may lead to better understanding of how fatigue initiation processes transit to cracks.« less

Auxiliary Propulsion Activities in Support of NASA's Exploration Initiative

NASA Technical Reports Server (NTRS)

Best, Philip J.; Unger, Ronald J.; Waits, David A.

2005-01-01

The Space Launch Initiative (SLI) procurement mechanism NRA8-30 initiated the Auxiliary Propulsion System/Main Propulsion System (APS/MPS) Project in 2001 to address technology gaps and development risks for non-toxic and cryogenic propellants for auxiliary propulsion applications. These applications include reaction control and orbital maneuvering engines, and storage, pressure control, and transfer technologies associated with on-orbit maintenance of cryogens. The project has successfully evolved over several years in response to changing requirements for re-usable launch vehicle technologies, general launch technology improvements, and, most recently, exploration technologies. Lessons learned based on actual hardware performance have also played a part in the project evolution to focus now on those technologies deemed specifically relevant to the Exploration Initiative. Formal relevance reviews held in the spring of 2004 resulted in authority for continuation of the Auxiliary Propulsion Project through Fiscal Year 2005 (FY05), and provided for a direct reporting path to the Exploration Systems Mission Directorate. The tasks determined to be relevant under the project were: continuation of the development, fabrication, and delivery of three 870 lbf thrust prototype LOX/ethanol reaction control engines; the fabrication, assembly, engine integration and testing of the Auxiliary Propulsion Test Bed at White Sands Test Facility; and the completion of FY04 cryogenic fluid management component and subsystem development tasks (mass gauging, pressure control, and liquid acquisition elements). This paper presents an overview of those tasks, their scope, expectations, and results to-date as carried forward into the Exploration Initiative.

[Research and workshop on alternative fuels for aviation. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1999-09-01

The Renewable Aviation Fuels Development Center (RAFDC) at Baylor University was granted U. S. Department of Energy (US DOE) and Federal Aviation Administration (FAA) funds for research and development to improve the efficiency in ethanol powered aircraft, measure performance and compare emissions of ethanol, Ethyl Tertiary Butyl Ether (ETBE) and 100 LL aviation gasoline. The premise of the initial proposal was to use a test stand owned by Engine Components Inc. (ECI) based in San Antonio, Texas. After the grant was awarded, ECI decided to close down its test stand facility. Since there were no other test stands available atmore » that time, RAFDC was forced to find additional support to build its own test stand. Baylor University provided initial funds for the test stand building. Other obstacles had to be overcome in order to initiate the program. The price of the emission testing equipment had increased substantially beyond the initial quote. Rosemount Analytical Inc. gave RAFDC an estimate of $120,000.00 for a basic emission testing package. RAFDC had to find additional funding to purchase this equipment. The electronic ignition unit also presented a series of time consuming problems. Since at that time there were no off-the-shelf units of this type available, one had to be specially ordered and developed. FAA funds were used to purchase a Super Flow dynamometer. Due to the many unforeseen obstacles, much more time and effort than originally anticipated had to be dedicated to the project, with much of the work done on a volunteer basis. Many people contributed their time to the program. One person, mainly responsible for the initial design of the test stand, was a retired engineer from Allison with extensive aircraft engine test stand experience. Also, many Baylor students volunteered to assemble the. test stand and continue to be involved in the current test program. Although the program presented many challenges, which resulted in delays, the RAFDC's test stand is an asset which provides an ongoing research capability dedicated to the testing of alternative fuels for aircraft engines. The test stand is now entirely functional with the exception of the electronic ignition unit which still needs adjustments.« less

Modeling Learning and Memory Using Verbal Learning Tests: Results From ACTIVE

PubMed Central

Gross, Alden L.

2013-01-01

Objective. To investigate the influence of memory training on initial recall and learning. Method. The Advanced Cognitive Training for Independent and Vital Elderly study of community-dwelling adults older than age 65 (n = 1,401). We decomposed trial-level recall in the Auditory Verbal Learning Test (AVLT) and Hopkins Verbal Learning Test (HVLT) into initial recall and learning across trials using latent growth models. Results. Trial-level increases in words recalled in the AVLT and HVLT at each follow-up visit followed an approximately logarithmic shape. Over the 5-year study period, memory training was associated with slower decline in Trial 1 AVLT recall (Cohen’s d = 0.35, p = .03) and steep pre- and posttraining acceleration in learning (d = 1.56, p < .001). Findings were replicated using the HVLT (decline in initial recall, d = 0.60, p = .01; pre- and posttraining acceleration in learning, d = 3.10, p < .001). Because of the immediate training boost, the memory-trained group had a higher level of recall than the control group through the end of the 5-year study period despite faster decline in learning. Discussion. This study contributes to the understanding of the mechanisms by which training benefits memory and expands current knowledge by reporting long-term changes in initial recall and learning, as measured from growth models and by characterization of the impact of memory training on these components. Results reveal that memory training delays the worsening of memory span and boosts learning. PMID:22929389

Task-shifting point-of-care CD4+ testing to lay health workers in HIV care and treatment services in Namibia.

PubMed

Kaindjee-Tjituka, Francina; Sawadogo, Souleymane; Mutandi, Graham; Maher, Andrew D; Salomo, Natanael; Mbapaha, Claudia; Neo, Marytha; Beukes, Anita; Gweshe, Justice; Muadinohamba, Alexinah; Lowrance, David W

2017-01-01

Access to CD4+ testing remains a common barrier to early initiation of antiretroviral therapy among persons living with HIV/AIDS in low- and middle-income countries. The feasibility of task-shifting of point-of-care (POC) CD4+ testing to lay health workers in Namibia has not been evaluated. From July to August 2011, Pima CD4+ analysers were used to improve access to CD4+ testing at 10 selected public health facilities in Namibia. POC Pima CD4+ testing was performed by nurses or lay health workers. Venous blood samples were collected from 10% of patients and sent to centralised laboratories for CD4+ testing with standard methods. Outcomes for POC Pima CD4+ testing and patient receipt of results were compared between nurses and lay health workers and between the POC method and standard laboratory CD4+ testing methods. Overall, 1429 patients received a Pima CD4+ test; 500 (35.0%) tests were performed by nurses and 929 (65.0%) were performed by lay health workers. When Pima CD4+ testing was performed by a nurse or a lay health worker, 93.2% and 95.2% of results were valid ( p = 0.1); 95.6% and 98.1% of results were received by the patient ( p = 0.007); 96.2% and 94.0% of results were received by the patient on the same day ( p = 0.08). Overall, 97.2% of Pima CD4+ results were received by patients, compared to 55.4% of standard laboratory CD4+ results ( p < 0.001). POC CD4+ testing was feasible and effective when task-shifted to lay health workers. Rollout of POC CD4+ testing via task-shifting can improve access to CD4+ testing and retention in care between HIV diagnosis and antiretroviral therapy initiation in low- and middle-income countries.

Community-Based Screening for Cervical Cancer: A Feasibility Study of Rural Appalachian Women

PubMed Central

Crosby, Richard A.; Hagensee, Michael E.; Vanderpool, Robin; Nelson, Nia; Parrish, Adam; Collins, Tom; Jones, Nebraska

2015-01-01

Objectives To describe women’s comfort levels and perceptions about their experience self-collecting cervico-vaginal swabs for HPV testing; to determine whether nurse-guided patient navigation increases the odds of women receiving a traditional Pap test after HPV screening; and to test the hypothesis that women testing positive for oncogenic HPV would be more likely to have a subsequent Pap test than those testing negative. Methods 400 women were recruited from eight rural Appalachian counties, in 2013 and 2014. After completing a survey, women were provided instructions for self-collecting a cervico-vaginal swab. Specimens were tested for 13 oncogenic HPV types. Simultaneously, women were notified of their test results and offered initial navigation for Pap testing. Chart-verified Pap testing within the next six months served as the endpoint. Results Comfort levels with self-collection were high: 89.2% indicated they would be more likely to self-collect a specimen for testing, on a regular basis, compared to Pap testing. Thirty women (7.5%) had a follow-up Pap test. Women receiving added nurse-guided navigation efforts were significantly less likely to have a subsequent test (P = .01). Women testing positive for oncogenic HPV were no more likely than those testing negative to have a subsequent Pap test (P = .27). Data were analyzed in 2014. Conclusions Rural Appalachian women are comfortable self-collecting cervico-vaginal swabs for HPV testing. Further, efforts to re-contact women who have received an oncogenic HPV test result and an initial navigation contact may not be useful. Finally, testing positive for oncogenic HPV may not be a motivational factor for subsequent Pap testing. PMID:26462184

The benchmark aeroelastic models program: Description and highlights of initial results

NASA Technical Reports Server (NTRS)

Bennett, Robert M.; Eckstrom, Clinton V.; Rivera, Jose A., Jr.; Dansberry, Bryan E.; Farmer, Moses G.; Durham, Michael H.

1991-01-01

An experimental effort was implemented in aeroelasticity called the Benchmark Models Program. The primary purpose of this program is to provide the necessary data to evaluate computational fluid dynamic codes for aeroelastic analysis. It also focuses on increasing the understanding of the physics of unsteady flows and providing data for empirical design. An overview is given of this program and some results obtained in the initial tests are highlighted. The tests that were completed include measurement of unsteady pressures during flutter of rigid wing with a NACA 0012 airfoil section and dynamic response measurements of a flexible rectangular wing with a thick circular arc airfoil undergoing shock boundary layer oscillations.

A study of space shuttle structural integrity test and assessment. Part 1

NASA Technical Reports Server (NTRS)

Anderson, R. E.; Poe, R. G.

1972-01-01

The ultrasonics technique for assessing the structural integrity of the primary surface of the space shuttle vehicles is discussed and evaluated. Analysis was made of transducers, transducer coupling test structure fabrication, flaws, and ultrasonic testing. Graphs of microphone response curves from the initial noise tests, accelerometer response curves from the final noise tests, and microphone curves from the final noise tests are included along with a glossary, bibliography, and results.

Development and Initial Validation of Perceived Competence and Satisfaction Measures for Racquet Sports.

ERIC Educational Resources Information Center

Aguilar, Teresita E.; Petrakis, Elizabeth

1989-01-01

The development and initial validation of the Racquet Sports Competence-Satisfaction Scale for measuring perceived competence and satisfaction in badminton, racquetball, and tennis is described. Results of a review panel and two field tests (with 168 and 208 university students) support the validity of the competence and satisfaction measures.…

An Empirical Investigation of Change in MCAT Scores upon Retest.

ERIC Educational Resources Information Center

Hynes, Kevin; Givner, Nathaniel

1980-01-01

An investigation of Medical College Admission Test (MCAT) retest scores indicates that limited retest improvement may result when initial scores are fairly low or below what might be predicted based on grade point averages. However, when initial scores approach the national, standardized MCAT mean, or are above what might be predicted, significant…

Rapid screening test for gestational diabetes: public health need, market requirement, initial product design, and experimental results

NASA Astrophysics Data System (ADS)

Weigl, Bernhard H.; Zwisler, Greg; Peck, Roger; Abu-Haydar, Elizabeth

2013-03-01

Gestational diabetes is a global epidemic where many urban areas in Southeast Asia have found prevalence rates as high as 20%, exceeding the highest prevalence rates in the developed world. It can have serious and life-threatening consequences for mothers and babies. We are developing two variants of a new, simple, low-cost rapid test for screening for gestational diabetes mellitus for use primarily in low-resource settings. The pair of assays, both semiquantitative rapid diagnostic strip tests for glycated albumin, require neither fasting nor an oral glucose challenge test. One variant is an extremely simple strip test to estimate the level of total glycated albumin in blood. The other, which is slightly more complex and expensive, is a test that determines the ratio of glycated albumin to total albumin. The screening results can be used to refer women to receive additional care during delivery to avoid birth complications as well as counseling on diet and exercise during and after pregnancy. Results with the latter test may also be used to start treatment with glucose-lowering drugs. Both assays will be read visually. We present initial results of a preliminary cost-performance comparison model evaluating the proposed test versus existing alternatives. We also evaluated user needs and schematic paper microfluidics-based designs aimed at overcoming the challenge of visualizing relatively narrow differences between normal and elevated levels of glycated albumin in blood.

Accuracy of Two Malaria Rapid Diagnostic Tests (RDTS) for Initial Diagnosis and Treatment Monitoring in a High Transmission Setting in Uganda

PubMed Central

Mbabazi, Phoebe; Hopkins, Heidi; Osilo, Emmanuel; Kalungu, Michael; Byakika-Kibwika, Pauline; Kamya, Moses R.

2015-01-01

Malaria rapid diagnostic tests (RDTs) may improve fever management in areas without microscopy. We compared the accuracy of histidine-rich protein 2 (HRP2) and Plasmodium lactate dehydrogenase (pLDH)-based RDTs, using expert microscopy as a gold standard, for initial diagnosis, treatment monitoring, and diagnosis of recurrent malaria in a cohort of children followed longitudinally in a high-transmission area in Uganda. For 305 initial fever episodes, sensitivity was 98% for HRP2 and 87% for pLDH, whereas specificity was 55% and 96%, respectively. The HRP2 gave 51% false-positive results on Day 28, whereas pLDH gave no false positives after Day 7. For 59 recurrent fever episodes during follow-up, sensitivity was 100% for HRP2 and 91% for pLDH, whereas specificity was 33% and 100%, respectively. The HRP2-based RDTs are useful for initial diagnosis of malaria caused by superior sensitivity; however, as a result of superior specificity, pLDH-based RDTs are more appropriate to monitor treatment and diagnose recurrent malaria. PMID:25624399

Serologic test systems development. Progress report, October 1, 1978-September 30, 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seawright, G.L.; Sanders, W.M.; Hollstein, U.

1980-12-01

Work has continued on the development and automation of enzyme immunoassays (EIA) for detecting diseases and toxic agents in food animals. Further evaluations were made of the Technicon Autoanalyzer II(AAII) for conducting totally automated EIAs. The problems investigated were machine carryover and assay variation. Modifications greatly reduced or eliminated carryover and produced acceptable levels of test variation. The EIA for swine trichinosis was significantly improved by the use of a new, partially purified antigen preparation. The result was improved detection of early seroconversions and reduced probability for false negatives and false positives. The amplified EIA was adapted as a diagnosticmore » test for bovine brucellosis and studies were initiated for differentiating vaccinated and infected animals. Preliminary data indicate that the IgG/sub 1/ response may be diagnostic but further studies are necessary. Development of the EIA for detecting low molecular weight contaminants and residues in food products was also initiated. Compounds studied were the antibiotics chloramphenicol, tetracycline, and gentamicin; the mycotoxin, aflatoxin, and the shale oil toxin, 2-aminofluorene. Results indicate that chloramphenicol nonspecifically binds to antibody and interferes with antibody activity. Thus, the test is not yet satisfactory. Initial attempts to automate the gentamicin test were unsuccessful because of machine carryover but modifications of the AAII have produced encouraging preliminary data. Work is continuing on the development of EIAs for all of the compounds mentioned above. (ERB)« less

In vitro assessment of artificial saliva formulations on initial enamel erosion remineralization.

PubMed

Ionta, Franciny Querobim; Mendonça, Fernanda Lyrio; de Oliveira, Gabriela Cristina; de Alencar, Catarina Ribeiro Barros; Honório, Heitor Marques; Magalhães, Ana Carolina; Rios, Daniela

2014-02-01

Various formulations of artificial saliva are present in the literature and little guidance is available on the standardization of type of saliva for use in in vitro protocols for erosive studies. The aim of this study was to evaluate the remineralizing capacity of different formulations of artificial saliva on initial enamel erosive lesion. Bovine enamel blocks were subjected to short-term acidic exposure by immersion in citric acid 0.05 M (pH 2.5) for 15s, resulting in surface softening without tissue loss. Then 90 selected eroded enamel blocks were randomly and equally divided into 6 groups according to saliva formulation (n=15): Saliva 1 (contain mucin); Saliva 2 (Saliva 1 without mucin); Saliva 3; Saliva 4; Saliva 5 (contain sodium carboxymethyl cellulose) and control (C) (deionized water). After demineralization enamel blocks were subjected to remineralization by immersion in the saliva's formulations for 2h. Enamel remineralization was measured by superficial hardness test (% superficial hardness change). The data were tested using ANOVA and Tukey's test (p<0.05). All the tested formulations of artificial saliva resulted in significantly higher enamel remineralization compared to control (p<0.001). Saliva 3 showed higher percentage of enamel remineralization than Saliva 5 (p<0.05). Besides the variety of artificial saliva for erosion in vitro protocols, all the formulations tested were able to partially remineralize initial erosive lesions. Copyright © 2013. Published by Elsevier Ltd.

Evaluation of the Mack Intelligent Vehicle Field Operational Test: September 2006

DOT National Transportation Integrated Search

2006-09-01

This report presents the final results of an independent evaluation of the U.S. Department of Transportation (USDOT) Mack Intelligent Vehicle Initiative (IVI) Field Operational Test (FOT). The IVI is a cooperative effort to conduct FOTs of advanced i...

MASH test 3-10 on 31-inch w-beam guardrail with standard offset blocks

DOT National Transportation Integrated Search

2011-03-01

The Texas Department of Transportation (TxDOT) initiated a review of their guardrail standards : based on the outcome of recent crash test results and a Federal Highway Administration technical : memorandum pertaining to guardrail height. TxDOT expre...

EMISSIONS FROM BURNING CABINET MAKING SCRAPS

EPA Science Inventory

The report gives results of an initial determination of differences in missions when burning ordinary cordwood compared to kitchen cabinet making scraps. he tests were performed in an instrumented woodstove testing laboratory on a stove that simulated units observed in use at a k...

Progress of Ongoing NASA Lithium-Ion Cell Verification Testing for Aerospace Applications

NASA Technical Reports Server (NTRS)

McKissock, Barbara I.; Manzo, Michelle A.; Miller, Thomas B.; Reid, Concha M.; Bennett, William R.; Gemeiner, Russel

2008-01-01

A Lithium-ion Verification and Validation Program with the purpose to assess the capabilities of current aerospace lithium-ion (Li-ion) battery cells to perform in a low-earth-orbit (LEO) regime was initiated in 2002. This program involves extensive characterization and LEO life testing at ten different combinations of depth-of-discharge, temperature, and end-of-charge voltage. The test conditions selected for the life tests are defined as part of a statistically designed test matrix developed to determine the effects of operating conditions on performance and life of Li-ion cells. Results will be used to model and predict cell performance and degradation as a function of test operating conditions. Testing is being performed at the Naval Surface Warfare Center/Crane Division in Crane, Indiana. Testing was initiated in September 2004 with 40 Ah cells from Saft and 30 Ah cells from Lithion. The test program has been expanded with the addition of modules composed of 18650 cells from ABSL Power Solutions in April 2006 and the addition of 50 Ah cells from Mine Safety Appliances Co. (MSA) in June 2006. Preliminary results showing the average voltage and average available discharge capacity for the Saft and Lithion packs at the test conditions versus cycles are presented.

Comparison of nozzle and afterbody surface pressures from wind tunnel and flight test of the YF-17 aircraft

NASA Technical Reports Server (NTRS)

Lucas, E. J.; Fanning, A. E.; Steers, L. I.

1978-01-01

Results are reported from the initial phase of an effort to provide an adequate technical capability to accurately predict the full scale, flight vehicle, nozzle-afterbody performance of future aircraft based on partial scale, wind tunnel testing. The primary emphasis of this initial effort is to assess the current capability and identify the cause of limitations on this capability. A direct comparison of surface pressure data is made between the results from an 0.1-scale model wind tunnel investigation and a full-scale flight test program to evaluate the current subscale testing techniques. These data were acquired at Mach numbers 0.6, 0.8, 0.9, 1.2, and 1.5 on four nozzle configurations at various vehicle pitch attitudes. Support system interference increments were also documented during the wind tunnel investigation. In general, the results presented indicate a good agreement in trend and level of the surface pressures when corrective increments are applied for known effects and surface differences between the two articles under investigation.

Summary of Booster Development and Qualification Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Francois, Elizabeth G.; Harry, Herbert H.; Hartline, Ernest L.

2012-06-21

This report outlines booster development work done at Los Alamos National Laboratory from 2007 to present. The booster is a critical link in the initiation train of explosive assemblies, from complex devices like nuclear weapons to conventional munitions. The booster bridges the gap from a small, relatively sensitive detonator to an insensitive, but massive, main charge. The movement throughout the explosives development community is to use more and more insensitive explosive components. With that, more energy is needed out of the booster. It has to initiate reliably, promptly, powerfully and safely. This report is divided into four sections. The firstmore » provides a summary of a collaborative effort between LANL, LLNL, and AWE to identify candidate materials and uniformly develop a testing plan for new boosters. Important parameters and the tests required to measure them were defined. The nature of the collaboration and the specific goals of the participating partners has changed over time, but the booster development plan stands on its own merit as a complete description of the test protocol necessary to compare and qualify booster materials, and is discussed in its entirety in this report. The second section describes a project, which began in 2009 with the Department of Defense to develop replacement booster formulations for PBXN-7. Replacement of PBXN-7 was necessary because it contained Triaminotrinitrobenzene (TATB), which was becoming unavailable to the DoD and because it contained Cyclotrimethylenetrinitramine (RDX), which was sensitive and toxic. A LANL-developed explosive, Diaminoazoxyfurazan (DAAF), was an important candidate. This project required any replacement formulation be a drop-in replacement in existing munitions. This project was timely, in that it made use of the collaborative booster development project, and had the additional constraint of matching shock sensitivity. Additionally it needed to be a safety improvement, and a performance improvement, especially at cold temperatures. The requirements of this project necessitated novel test development and a different approach to ranking booster qualities. Results of this project have been documented to the DoD and the relevant portions are included within. The third section of this booster report outlines testing related to main charge initiation merit. Initiability can be evaluated by looking at critical diameter, run distance, and shock sensitivity. Once a booster is initiated, it needs to be powerful enough to initiate the main charge symmetrically and evenly. Main charge initiability is evaluated directly by observing detonation wave symmetry, curvature, and first break out over the surface of a charge. Furthermore it must be insensitive to accidents and insults, and safe and reliable across a range of temperatures. These effects, tests, and results will be discussed individually in the context of DAAF and other explosives similarly tested. The last section provides a conclusion and summary of our experimental work and recommendations for the path forward. References and additional supporting documentation and results are provided in the appendices at the end of this report.« less

Indeterminate QuantiFERON-TB Gold Increases Likelihood of Inflammatory Bowel Disease Treatment Delay and Hospitalization.

PubMed

Vajravelu, Ravy K; Osterman, Mark T; Aberra, Faten N; Roy, Jason A; Lichtenstein, Gary R; Mamtani, Ronac; Goldberg, David S; Lewis, James D; Scott, Frank I

2017-12-19

QuantiFERON-TB Gold (QFTG) is a blood test used to diagnose latent tuberculosis infection (LTBI) prior to TNF-α inhibitor (anti-TNF) initiation. We sought to determine factors associated with indeterminate QFTG results in inflammatory bowel disease (IBD) patients and whether indeterminate results are associated with IBD-related morbidity. This nested case-control study included IBD patients who underwent QFTG testing. Cases were patients with indeterminate QFTG and controls were those with negative QFTG. The association of demographic and clinical data with indeterminate QFTG result was assessed using logistic regression. We examined the clinical impact of indeterminate QFTG results on risk of hospitalization and delay in anti-TNF initiation using inverse probability-of-treatment weighting (IPTW) regression. We identified 411 patients with QFTG testing (320 negative, 80 indeterminate, and 11 positive results). No patient with an indeterminate result subsequently had LTBI. Systemic corticosteroid use (OR, 4.4; 95% CI, 2.0-9.6) and hospitalization at the time of QFTG (OR, 3.8; 95% CI, 1.9-7.7) were associated with indeterminate QFTG, while immunomodulator use was nearly statistically significant (OR, 3.1; 95% CI, 0.9-9.8) and anti-TNF use was not (OR, 0.9; 95% CI, 0.2-4.6). After IPTW adjustment, indeterminate QFTG was associated with a 23.1% (95% CI, 8.2%-37.9%) greater probability of delay in anti-TNF initiation beyond 30 days and an 11.9% (95% CI, 0.6%-23.1%) greater probability of hospitalization within 60 days. Systemic corticosteroid use and hospitalization were associated with an indeterminate QFTG result. Indeterminate QFTG results were associated with delayed anti-TNF initiation and subsequent hospitalization. © 2017 Crohn’s & Colitis Foundation of America. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Initialization of hydrodynamics in relativistic heavy ion collisions with an energy-momentum transport model

NASA Astrophysics Data System (ADS)

Naboka, V. Yu.; Akkelin, S. V.; Karpenko, Iu. A.; Sinyukov, Yu. M.

2015-01-01

A key ingredient of hydrodynamical modeling of relativistic heavy ion collisions is thermal initial conditions, an input that is the consequence of a prethermal dynamics which is not completely understood yet. In the paper we employ a recently developed energy-momentum transport model of the prethermal stage to study influence of the alternative initial states in nucleus-nucleus collisions on flow and energy density distributions of the matter at the starting time of hydrodynamics. In particular, the dependence of the results on isotropic and anisotropic initial states is analyzed. It is found that at the thermalization time the transverse flow is larger and the maximal energy density is higher for the longitudinally squeezed initial momentum distributions. The results are also sensitive to the relaxation time parameter, equation of state at the thermalization time, and transverse profile of initial energy density distribution: Gaussian approximation, Glauber Monte Carlo profiles, etc. Also, test results ensure that the numerical code based on the energy-momentum transport model is capable of providing both averaged and fluctuating initial conditions for the hydrodynamic simulations of relativistic nuclear collisions.

Trends in CD4 Count Testing, Retention in Pre-ART Care, and ART Initiation Rates over the First Decade of Expansion of HIV Services in Haiti

PubMed Central

Koenig, Serena P.; Bernard, Daphne; Dévieux, Jessy G.; Atwood, Sidney; McNairy, Margaret L.; Severe, Patrice; Marcelin, Adias; Julma, Pierrot; Apollon, Alexandra; Pape, Jean W.

2016-01-01

Background High attrition during the period from HIV testing to antiretroviral therapy (ART) initiation is widely reported. Though treatment guidelines have changed to broaden ART eligibility and services have been widely expanded over the past decade, data on the temporal trends in pre-ART outcomes are limited; such data would be useful to guide future policy decisions. Methods We evaluated temporal trends and predictors of retention for each step from HIV testing to ART initiation over the past decade at the GHESKIO clinic in Port-au-Prince Haiti. The 24,925 patients >17 years of age who received a positive HIV test at GHESKIO from March 1, 2003 to February 28, 2013 were included. Patients were followed until they remained in pre-ART care for one year or initiated ART. Results 24,925 patients (61% female, median age 35 years) were included, and 15,008 (60%) had blood drawn for CD4 count within 12 months of HIV testing; the trend increased over time from 36% in Year 1 to 78% in Year 10 (p<0.0001). Excluding transfers, the proportion of patients who were retained in pre-ART care or initiated ART within the first year after HIV testing was 84%, 82%, 64%, and 64%, for CD4 count strata ≤200, 201 to 350, 351 to 500, and >500 cells/mm3, respectively. The trend increased over time for each CD4 strata, and in Year 10, 94%, 95%, 79%, and 74% were retained in pre-ART care or initiated ART for each CD4 strata. Predictors of pre-ART attrition included male gender, low income, and low educational status. Older age and tuberculosis (TB) at HIV testing were associated with retention in care. Conclusions The proportion of patients completing assessments for ART eligibility, remaining in pre-ART care, and initiating ART have increased over the last decade across all CD4 count strata, particularly among patients with CD4 count ≤350 cells/mm3. However, additional retention efforts are needed for patients with higher CD4 counts. PMID:26901795

Initial Single Event Effects Testing of the Xilinx Virtex-4 Field Programmable Gate Array

NASA Technical Reports Server (NTRS)

Allen, Gregory R.; Swift, Gary M.; Carmichael, C.; Tseng, C.

2007-01-01

We present initial results for the thin epitaxial Xilinx Virtex-4 Fie ld Programmable Gate Array (FPGA), and compare to previous results ob tained for the Virtex-II and Virtex-II Pro. The data presented was a cquired through a consortium based effort with the common goal of pr oviding the space community with data and mitigation methods for the use of Xilinx FPGAs in space.

The space shuttle ascent vehicle aerodynamic challenges configuration design and data base development

NASA Technical Reports Server (NTRS)

Dill, C. C.; Young, J. C.; Roberts, B. B.; Craig, M. K.; Hamilton, J. T.; Boyle, W. W.

1985-01-01

The phase B Space Shuttle systems definition studies resulted in a generic configuration consisting of a delta wing orbiter, and two solid rocket boosters (SRB) attached to an external fuel tank (ET). The initial challenge facing the aerodynamic community was aerodynamically optimizing, within limits, this configuration. As the Shuttle program developed and the sensitivities of the vehicle to aerodynamics were better understood the requirements of the aerodynamic data base grew. Adequately characterizing the vehicle to support the various design studies exploded the size of the data base to proportions that created a data modeling/management challenge for the aerodynamicist. The ascent aerodynamic data base originated primarily from wind tunnel test results. The complexity of the configuration rendered conventional analytic methods of little use. Initial wind tunnel tests provided results which included undesirable effects from model support tructure, inadequate element proximity, and inadequate plume simulation. The challenge to improve the quality of test results by determining the extent of these undesirable effects and subsequently develop testing techniques to eliminate them was imposed on the aerodynamic community. The challenges to the ascent aerodynamics community documented are unique due to the aerodynamic complexity of the Shuttle launch. Never before was such a complex vehicle aerodynamically characterized. The challenges were met with innovative engineering analyses/methodology development and wind tunnel testing techniques.

Use of a 17-Gene Prognostic Assay in Contemporary Urologic Practice: Results of an Interim Analysis in an Observational Cohort.

PubMed

Eure, Gregg; Germany, Raymond; Given, Robert; Lu, Ruixiao; Shindel, Alan W; Rothney, Megan; Glowacki, Richard; Henderson, Jonathan; Richardson, Tim; Goldfischer, Evan; Febbo, Phillip G; Denes, Bela S

2017-09-01

To study the impact of genomic testing in shared decision making for men with clinically low-risk prostate cancer (PCa). Patients with clinically low-risk PCa were enrolled in a prospective, multi-institutional study of a validated 17-gene tissue-based reverse transcription polymerase chain reaction assay (Genomic Prostate Score [GPS]). In this paper we report on outcomes in the first 297 patients enrolled in the study with valid 17-gene assay results and decision-change data. The primary end points were shared decision on initial management and persistence on active surveillance (AS) at 1 year post diagnosis. AS utilization and persistence were compared with similar end points in a group of patients who did not have genomic testing (baseline cohort). Secondary end points included perceived utility of the assay and patient decisional conflict before and after testing. One-year results were available on 258 patients. Shift between initial recommendation and shared decision occurred in 23% of patients. Utilization of AS was higher in the GPS-tested cohort than in the untested baseline cohort (62% vs 40%). The proportion of men who selected and persisted on AS at 1 year was 55% and 34% in the GPS and baseline cohorts, respectively. Physicians reported that GPS was useful in 90% of cases. Mean decisional conflict scores declined in patients after GPS testing. Patients who received GPS testing were more likely to select and persist on AS for initial management compared with a matched baseline group. These data indicate that GPS help guide shared decisions in clinically low-risk PCa. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

40 CFR 63.2261 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... tests upon initial startup or no later than 180 calendar days after the compliance date that is... conduct initial compliance demonstrations that do not require performance tests upon initial startup or no...

40 CFR 75.20 - Initial certification and recertification procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... all applicable initial certification tests under paragraph (c) of this section are completed by the... installed, initial certification is required. (1) Notification of initial certification test dates. The...) tests. (4) Certification (or recertification) application formal approval process. The Administrator...

40 CFR 75.20 - Initial certification and recertification procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... all applicable initial certification tests under paragraph (c) of this section are completed by the... installed, initial certification is required. (1) Notification of initial certification test dates. The...) tests. (4) Certification (or recertification) application formal approval process. The Administrator...

40 CFR 75.20 - Initial certification and recertification procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... all applicable initial certification tests under paragraph (c) of this section are completed by the... installed, initial certification is required. (1) Notification of initial certification test dates. The...) tests. (4) Certification (or recertification) application formal approval process. The Administrator...

DANTi: Detect and Avoid iN The Cockpit

NASA Technical Reports Server (NTRS)

Chamberlain, James; Consiglio, Maria; Munoz, Cesar

2017-01-01

Mid-air collision risk continues to be a concern for manned aircraft operations, especially near busy non-towered airports. The use of Detect and Avoid (DAA) technologies and draft standards developed for unmanned aircraft systems (UAS), either alone or in combination with other collision avoidance technologies, may be useful in mitigating this collision risk for manned aircraft. This paper describes a NASA research effort known as DANTi (DAA iN The Cockpit), including the initial development of the concept of use, a software prototype, and results from initial flight tests conducted with this prototype. The prototype used a single Automatic Dependent Surveillance - Broadcast (ADS-B) traffic sensor and the own aircraft's position, track, heading and air data information, along with NASA-developed DAA software to display traffic alerts and maneuver guidance to manned aircraft pilots on a portable tablet device. Initial flight tests with the prototype showed a successful DANTi proof-of-concept, but also demonstrated that the traffic separation parameter set specified in the RTCA SC-228 Phase I DAA MOPS may generate excessive false alerts during traffic pattern operations. Several parameter sets with smaller separation values were also tested in flight, one of which yielded more timely alerts for the maneuvers tested. Results from this study may further inform future DANTi efforts as well as Phase II DAA MOPS development.

Reentry Motion and Aerodynamics of the MUSES-C Sample Return Capsule

NASA Astrophysics Data System (ADS)

Ishii, Nobuaki; Yamada, Tetsuya; Hiraki, Koju; Inatani, Yoshifumi

The Hayabusa spacecraft (MUSES-C) carries a small capsule for bringing asteroid samples back to the earth. The initial spin rate of the reentry capsule together with the flight path angle of the reentry trajectory is a key parameter for the aerodynamic motion during the reentry flight. The initial spin rate is given by the spin-release mechanism attached between the capsule and the mother spacecraft, and the flight path angle can be modified by adjusting the earth approach orbit. To determine the desired values of both parameters, the attitude motion during atmospheric flight must be clarified, and angles of attack at the maximum dynamic pressure and the parachute deployment must be assessed. In previous studies, to characterize the aerodynamic effects of the reentry capsule, several wind-tunnel tests were conducted using the ISAS high-speed flow test facilities. In addition to the ground test data, the aerodynamic properties in hypersonic flows were analyzed numerically. Moreover, these data were made more accurate using the results of balloon drop tests. This paper summarized the aerodynamic properties of the reentry capsule and simulates the attitude motion of the full-configuration capsule during atmospheric flight in three dimensions with six degrees of freedom. The results show the best conditions for the initial spin rates and flight path angles of the reentry trajectory.

Precursor Evolution and Stress Corrosion Cracking Initiation of Cold-Worked Alloy 690 in Simulated Pressurized Water Reactor Primary Water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhai, Ziqing; Toloczko, Mychailo; Kruska, Karen

Stress corrosion crack initiation of two thermally-treated, cold-worked (CW) alloy 690 (UNS N06690) materials was investigated in 360oC simulated PWR primary water using constant load tensile (CLT) tests and blunt notch compact tension (BNCT) tests equipped with direct current potential drop (DCPD) for in-situ detection of cracking. SCC initiation was not detected by DCPD for either the 21% or 31%CW CLT specimens loaded at their yield stress after ~9,220 hours, however intergranular (IG) precursor damage and isolated surface cracks were observed on the specimens. The two 31%CW BNCT specimens loaded at moderate stress intensity after several cyclic loading ramps showedmore » DCPD-indicated crack initiation after 10,400 hours of exposure at constant stress intensity, which was resulted from significant growth of IG cracks. The 21%CW BNCT specimens only exhibited isolated small IG surface cracks and showed no apparent DCPD change throughout the test. Post-test cross-section examinations revealed many grain boundary (GB) nano-cavities in the bulk of all the CLT and BNCT specimens particularly for the 31%CW materials. Cavities were also found along GBs extending to the surface suggesting an important role in crack nucleation. This paper provides an overview of the evolution of GB cavities and discusses their effects on crack initiation in CW alloy 690.« less

Evaluation of the river die-away biodegradation test

USGS Publications Warehouse

Wylie, Glenn D.; Jones, John R.; Johnson, B. Thomas

1982-01-01

The reliability of the river die-away (RDA) test for establishing the biodegradability of chemicals was assessed. Reproducibility of biodegradation in the RDA test was analyzed under conditions in which the test is commonly done. Biodegradation results were not reproducible for di-2-ethylexyl phthalate (DEHP) and phthalic acid in replicated RDA tests using Missouri River water. Chemical and biological changes during the RDA tests probably reflected relative laboratory conditions. Initial suspended solids and subsequent DEHP biodegradation were directly related. Interpretation of RDA test results is enhanced by replicating experiments and comparing biodegradation of the test compound with a compound whose degradation properties are known. However, biodegradation measured with the RDA test is too variable and too dependent on laboratory treatment of samples to apply results directly to the aquatic environment.

Provider variation in the quality of metabolic stone management.

PubMed

Dauw, Casey A; Alruwaily, Abdulrahman F; Bierlein, Maggie J; Asplin, John R; Ghani, Khurshid R; Wolf, J Stuart; Hollingsworth, John M

2015-03-01

Urinary stone disease is a chronic condition for which secondary prevention (dietary and medical therapy guided by 24-hour urine collection results) has an important role. Assessing the response to these interventions with followup testing is recommended and yet to our knowledge provider compliance with these guidelines is unknown. Using Litholink® files from 1995 to 2013 we identified adults with urinary stone disease who underwent metabolic evaluation and the providers who ordered the evaluation. By focusing on patients with an abnormality on the initial collection we determined the proportion who underwent a followup test within 6 months of the initial test. Multilevel modeling was done to quantify variation in followup testing among providers after accounting for various patient and provider factors. A total of 208,125 patients had an abnormality on the initial collection, of whom only 33,413 (16.1%) performed a repeat collection within 6 months. While most variation in followup testing was attributable to the patient, the provider contribution was nontrivial (18.0%). The specialty of the ordering provider was important. Patients who saw a urologist had 24% lower odds of repeat testing compared to those who saw a primary care physician (OR 0.76, 95% CI 0.67-0.86, p <0.001). Followup testing is uncommon in patients with an abnormal initial 24-hour urine collection. Given the observed provider variation, efforts to educate providers on the value of followup testing are likely to have salutary effects on patients with metabolic stone disease. Copyright © 2015 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

Physical and chemical test results of electrostatic safe flooring materials

NASA Technical Reports Server (NTRS)

Gompf, R. H.

1988-01-01

This test program was initiated because a need existed at the Kennedy Space Center (KSC) to have this information readily available to the engineer who must make the choice of which electrostatic safe floor to use in a specific application. The information, however, should be of value throughout both the government and private industry in the selection of a floor covering material. Included are the test results of 18 floor covering materials which by test evaluation at KSC are considered electrostatically safe. Tests were done and/or the data compiled in the following areas: electrostatics, flammability, hypergolic compatibility, outgassing, floor type, material thickness, and available colors. Each section contains the test method used to gather the data and the test results.

MATD Operational Phase: Experiences and Lessons Learned

NASA Astrophysics Data System (ADS)

Messidoro, P.; Bader, M.; Brunner, O.; Cerrato, A.; Sembenini, G.

2004-08-01

The Model And Test Effectiveness Database (MATD) initiative is ending the first year of its operational phase. MATD represents a common repository of project data, Assembly Integration and Verification (AIV) data, on ground and flight anomalies data, of recent space projects, and offers, with the application of specific methodologies, the possibility to analyze the collected data in order to improve the test philosophies and the related standards. Basically the following type of results can be derived from the database: - Statistics on ground failures and flight anomalies - Feed-back from the flight anomalies to the Test Philosophies - Test Effectiveness evaluation at system and lower levels - Estimate of the index of effectiveness of a specific Model and Test Philosophy in comparison with the applicable standards - Simulation of different Test philosophies and related balancing of Risk/cost/schedule on the basis of MATD data The paper after a short presentation of the status of the MATD initiative, summarises the most recent lessons learned which are resulting from the data analysis and highlights how MATD is being utilized for the actual risk/cost/schedule/Test effectiveness evaluations of the past programmes so as for the prediction of the new space projects.

Launching nurse-initiated HIV rapid testing in Veterans Affairs primary care: a comprehensive overview of a self-sustaining implementation.

PubMed

Knapp, H; Anaya, H D; Feld, J E; Hoang, T; Goetz, M B

2011-12-01

Our objectives were to use foundational pilot findings to guide the implementation of an HIV rapid testing (RT) intervention at one Veterans Affairs outpatient clinic and to evaluate the success and sustainability of this intervention over the course of one year. Policy modifications were drafted and adopted to enable nurses to order, administer, interpret and document HIV RTs. Staff enrolled in a two-part training sessions designed to teach pre- and post-test counselling techniques and the mechanics of administering, interpreting and coding test results in the patients' medical records. They were subsequently evaluated on their efforts at: (1) increasing HIV RT, (2) sustaining this effort one year post-launch. Enabling nurses to carry out HIV RT resulted in a significant increase in not only HIV RT, but also HIV testing rates overall at this facility, measured over the first year of this implementation. Our findings indicate that targeted strategies, aimed at increasing HIV RT rates, worked to increase testing rates overall, and also, that our initial testing strategies were independently sustainable, which is in contrast to findings in the literature on implementation science.

Clinical and Organizational Factors in the Initial Evaluation of Patients With Lung Cancer

PubMed Central

Jim Yeung, Sai-Ching; Tanoue, Lynn T.; Gould, Michael K.

2013-01-01

Background: This guideline is intended to provide an evidence-based approach to the initial evaluation of patients with known or suspected lung cancer. It also includes an assessment of the impact of timeliness of care and multidisciplinary teams on outcome. Methods: The applicable current medical literature was identified by a computerized search and evaluated using standardized methods. Recommendations were framed using the approach described by the Guidelines Oversight Committee of the American College of Chest Physicians. Data sources included MEDLINE and the Cochrane Database of Systematic Reviews. Results: Initial evaluation should include a thorough history and physical examination; CT imaging; pulmonary function tests; and hemoglobin, electrolyte, liver function, and calcium levels. Additional testing for distant metastases and paraneoplastic syndromes should be determined on the basis of these results. Paraneoplastic syndromes may have an adverse impact on cancer treatment, so they should be controlled rapidly with the goal of proceeding with definitive cancer treatment in a timely manner. Although the relationship between timeliness of care and survival is difficult to quantify, efforts to deliver timely care are reasonable and should be balanced with the need to attend to other dimensions of health-care quality (eg, safety, effectiveness, efficiency, equality, consistency with patient values and preferences). Quality care will require multiple disciplines. Although it is difficult to assess the impact, we suggest that a multidisciplinary team approach to care be used, particularly for patients requiring multimodality therapy. Conclusions: The initial evaluation of patients with lung cancer should include a thorough history and physical examination, pulmonary function tests, CT imaging, basic laboratory tests, and selective testing for distant metastases and paraneoplastic syndromes. PMID:23649435

ACAS-Xu Initial Self-Separation Flight Tests

NASA Technical Reports Server (NTRS)

Marston, Mike; Baca, Gabe

2015-01-01

The purpose of this flight test report is to document and report the details of the ACAS Xu (Airborne Collision Avoidance System For Unmanned Aircraft) / Self-Separation flight test series performed at Edwards AFB from November to December of 2014. Included in this document are details about participating aircraft, aircrew, mission crew, system configurations, flight data, flight execution, flight summary, test results, and lessons learned.

10 CFR Appendix J to Part 50 - Primary Reactor Containment Leakage Testing for Water-Cooled Power Reactors

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Containment inspection. B. Repordkeeping of test results. I. Introduction One of the conditions of all... following: A. Type A test—1. Pretest requirements. (a) Containment inspection in accordance with V. A. shall.... During the period between the completion of one Type A test and the initiation of the containment...

Students' Initial Knowledge of Electric and Magnetic Fields--More Profound Explanations and Reasoning Models for Undesired Conceptions

ERIC Educational Resources Information Center

Saarelainen, M.; Laaksonen, A.; Hirvonen, P. E.

2007-01-01

This study explores undergraduate students' understanding and reasoning models of electric and magnetic fields. The results indicate that the tested students had various alternative concepts in applying their reasoning to certain CSEM test questions. The total number of physics students tested at the beginning of the first course on…

Many Children Left Behind? Textbooks and Test Scores in Kenya. NBER Working Paper No. 13300

ERIC Educational Resources Information Center

Glewwe, Paul; Kremer, Michael; Moulin, Sylvie

2007-01-01

A randomized evaluation suggests that a program which provided official textbooks to randomly selected rural Kenyan primary schools did not increase test scores for the average student. In contrast, the previous literature suggests that textbook provision has a large impact on test scores. Disaggregating the results by students' initial academic…

Estimating retention in HIV care accounting for patient transfers: A national laboratory cohort study in South Africa.

PubMed

Fox, Matthew P; Bor, Jacob; Brennan, Alana T; MacLeod, William B; Maskew, Mhairi; Stevens, Wendy S; Carmona, Sergio

2018-06-01

Systematic reviews have described high rates of attrition in patients with HIV receiving antiretroviral therapy (ART). However, migration and clinical transfer may lead to an overestimation of attrition (death and loss to follow-up). Using a newly linked national laboratory database in South Africa, we assessed national retention in South Africa's national HIV program. Patients receiving care in South Africa's national HIV program are monitored through regular CD4 count and viral load testing. South Africa's National Health Laboratory Service has maintained a database of all public-sector CD4 count and viral load results since 2004. We linked individual laboratory results to patients using probabilistic matching techniques, creating a national HIV cohort. Validation of our approach in comparison to a manually matched dataset showed 9.0% undermatching and 9.5% overmatching. We analyzed data on patients initiating ART in the public sector from April 1, 2004, to December 31, 2006, when ART initiation could be determined based on first viral load among those whose treatment followed guidelines. Attrition occurred on the date of a patient's last observed laboratory measure, allowing patients to exit and reenter care prior to that date. All patients had 6 potential years of follow-up, with an additional 2 years to have a final laboratory measurement to be retained at 6 years. Data were censored at December 31, 2012. We assessed (a) national retention including all laboratory tests regardless of testing facility and (b) initiating facility retention, where laboratory tests at other facilities were ignored. We followed 55,836 patients initiating ART between 2004 and 2006. At ART initiation, median age was 36 years (IQR: 30-43), median CD4 count was 150 cells/mm3 (IQR: 81-230), and 66.7% were female. Six-year initiating clinic retention was 29.1% (95% CI: 28.7%-29.5%). After allowing for transfers, national 6-year retention was 63.3% (95% CI: 62.9%-63.7%). Results differed little when tightening or relaxing matching procedures. We found strong differences in retention by province, ranging from 74.2% (95% CI: 73.2%-75.2%) in Western Cape to 52.2% (95% CI: 50.6%-53.7%) in Mpumalanga at 6 years. National attrition was higher among patients initiating at lower CD4 counts and higher viral loads, and among patients initiating ART at larger facilities. The study's main limitation is lack of perfect cohort matching, which may lead to over- or underestimation of retention. We also did not have data from KwaZulu-Natal province prior to 2010. In this study, HIV care retention was substantially higher when viewed from a national perspective than from a facility perspective. Our results suggest that traditional clinical cohorts underestimate retention.

The effect of lithium chloride on one-trial passive avoidance learning in rats.

PubMed Central

Johnson, F N

1976-01-01

1 Expression of a one-trial passive avoidance learning response in rats was examined following injections of lithium chloride or sodium chloride before and after initial training and before the first day of testing. Five tests were given at daily intervals, 24 h after training being the time of the first test. 2. Lithium given before the first day of testing impaired response expression on the first and all subsequent days of testing; the rate of extinction was unaffected. 3. Given both before and immediately after initial training, lithium impaired response expression on the first day of testing but slowed down the subsequent rate of extinction, leading eventually to improved performance on the fifth day, as compared with placebo-treated control subjects. 4. The results are interpreted in the light of the hypothesis that lithium impaired the central processing of sensory information. PMID:1252666

Association Between Direct-to-Consumer Advertising and Testosterone Testing and Initiation in the United States, 2009-2013.

PubMed

Layton, J Bradley; Kim, Yoonsang; Alexander, G Caleb; Emery, Sherry L

2017-03-21

Testosterone initiation increased substantially in the United States from 2000 to 2013, especially among men without clear indications. Direct-to-consumer advertising (DTCA) also increased during this time. To investigate associations between televised DTCA and testosterone testing and initiation in the United States. Ecologic study conducted in designated market areas (DMAs) in the United States. Monthly testosterone advertising ratings were linked to DMA-level testosterone use data from 2009-2013 derived from commercial insurance claims. Associations between DTCA and testosterone testing, initiation, and initiation without recent baseline tests were estimated using Poisson generalized estimating equations. Monthly Nielsen ratings for testosterone DTCA in the 75 largest DMAs. (1) Rates of new serum testosterone testing; (2) rates of testosterone initiation (in-office injection, surgical implant, or pharmacy dispensing) for all testosterone products combined and for specific brands; and (3) rates of testosterone initiation without recent serum testosterone testing. Of 17 228 599 commercially insured men in the 75 DMAs, 1 007 990 (mean age, 49.6 [SD, 11.5] years) had new serum testosterone tests and 283 317 (mean age, 51.8 [SD, 11.3] years) initiated testosterone treatment. Advertising intensity varied by geographic region and time, with the highest intensity seen in the southeastern United States and with months ranging from no ad exposures to a mean of 13.6 exposures per household. Nonbranded advertisements were common prior to 2012, with branded advertisements becoming more common during and after 2012. Each household advertisement exposure was associated with a monthly increase in rates of new testosterone testing (rate ratio [RR], 1.006; 95% CI, 1.004-1.008), initiation (RR, 1.007; 95% CI, 1.004-1.010), and initiation without a recent test (RR, 1.008; 95% CI, 1.002-1.013). Mean absolute rate increases were 0.14 tests (95% CI, 0.09-0.19), 0.05 new initiations (95% CI, 0.03-0.08), and 0.02 initiations without a recent test (95% CI, 0.01-0.03) per 10 000 men for each monthly ad exposure over the entire period. Among US men residing in the 75 designated market areas, regional exposure to televised direct-to-consumer advertising was associated with greater testosterone testing, new initiation, and initiation without recent testing.

Screening HIV-Infected Patients with Low CD4 Counts for Cryptococcal Antigenemia prior to Initiation of Antiretroviral Therapy: Cost Effectiveness of Alternative Screening Strategies in South Africa.

PubMed

Larson, Bruce A; Rockers, Peter C; Bonawitz, Rachael; Sriruttan, Charlotte; Glencross, Deborah K; Cassim, Naseem; Coetzee, Lindi M; Greene, Gregory S; Chiller, Tom M; Vallabhaneni, Snigdha; Long, Lawrence; van Rensburg, Craig; Govender, Nelesh P

2016-01-01

In 2015 South Africa established a national cryptococcal antigenemia (CrAg) screening policy targeted at HIV-infected patients with CD4+ T-lymphocyte (CD4) counts <100 cells/ μl who are not yet on antiretroviral treatment (ART). Two screening strategies are included in national guidelines: reflex screening, where a CrAg test is performed on remnant blood samples from CD4 testing; and provider-initiated screening, where providers order a CrAg test after a patient returns for CD4 test results. The objective of this study was to compare costs and effectiveness of these two screening strategies. We developed a decision analytic model to compare reflex and provider-initiated screening in terms of programmatic and health outcomes (number screened, number identified for preemptive treatment, lives saved, and discounted years of life saved) and screening and treatment costs (2015 USD). We estimated a base case with prevalence and other parameters based on data collected during CrAg screening pilot projects integrated into routine HIV care in Gauteng, Free State, and Western Cape Provinces. We conducted sensitivity analyses to explore how results change with underlying parameter assumptions. In the base case, for each 100,000 CD4 tests, the reflex strategy compared to the provider-initiated strategy has higher screening costs ($37,536 higher) but lower treatment costs ($55,165 lower), so overall costs of screening and treatment are $17,629 less with the reflex strategy. The reflex strategy saves more lives (30 lives, 647 additional years of life saved). Sensitivity analyses suggest that reflex screening dominates provider-initiated screening (lower total costs and more lives saved) or saves additional lives for small additional costs (< $125 per life year) across a wide range of conditions (CrAg prevalence, patient and provider behavior, patient survival without treatment, and effectiveness of preemptive fluconazole treatment). In countries with substantial numbers of people with untreated, advanced HIV disease such as South Africa, CrAg screening before initiation of ART has the potential to reduce cryptococcal meningitis and save lives. Reflex screening compared to provider-initiated screening saves more lives and is likely to be cost saving or have low additional costs per additional year of life saved.

Self-initiated object-location memory in young and older adults.

PubMed

Berger-Mandelbaum, Anat; Magen, Hagit

2017-11-20

The present study explored self-initiated object-location memory in ecological contexts, as aspect of memory that is largely absent from the research literature. Young and older adults memorized objects-location associations they selected themselves or object-location associations provided to them, and elaborated on the strategy they used when selecting the locations themselves. Retrieval took place 30 min and 1 month after encoding. The results showed an age-related decline in self-initiated and provided object-location memory. Older adults benefited from self-initiation more than young adults when tested after 30 min, while the benefit was equal when tested after 1 month. Furthermore, elaboration enhanced memory only in older adults, and only after 30 min. Both age groups used deep encoding strategies on the majority of the trials, but their percentage was lower in older adults. Overall, the study demonstrated the processes involved in self-initiated object-location memory, which is an essential part of everyday functioning.

Active Protection of an MgB2 Test Coil

PubMed Central

Park, Dong Keun; Hahn, Seungyong; Bascuñán, Juan; Iwasa, Yukikazu

2011-01-01

This paper presents results of a study, experimental and computational, of a detect-and-activate-the-heater protection technique applied to a magnesium diboride (MgB2) test coil operated in semi-persistent mode. The test coil with a winding ID of 25 cm and wound with ~500-m long reacted MgB2 wire was operated at 4.2 K immersed in a bath of liquid helium. In this active technique, upon the initiation of a “hot spot” of a length ~10 cm, induced by a “quench heater,” a “protection heater” (PH) of ~600-cm long planted within the test coil is activated. The normal zone created by the PH is large enough to absorb the test coil’s entire initial stored energy and still keeps the peak temperature within the winding below ~260 K. PMID:22081754

Development and qualification testing of a laser-ignited, all-secondary (DDT) detonator

NASA Technical Reports Server (NTRS)

Blachowski, Thomas J.; Krivitsky, Darrin Z.; Tipton, Stephen

1994-01-01

The Indian Head Division, Naval Surface Warfare Center (IHDIV, NSWC) is conducting a qualification program for a laser-ignited, all-secondary (DDT) explosive detonator. This detonator was developed jointly by IHDIV, NSWC and the Department of Energy's EG&G Mound Applied Technologies facility in Miamisburg, Ohio to accept a laser initiation signal and produce a fully developed shock wave output. The detonator performance requirements were established by the on-going IHDIV, NSWC Laser Initiated Transfer Energy Subsystem (LITES) advanced development program. Qualification of the detonator as a component utilizing existing military specifications is the selected approach for this program. The detonator is a deflagration-to-detonator transfer (DDT) device using a secondary explosive, HMX, to generate the required shock wave output. The prototype development and initial system integration tests for the LITES and for the detonator were reported at the 1992 International Pyrotechnics Society Symposium and at the 1992 Survival and Flight Equipment National Symposium. Recent results are presented for the all-fire sensitivity and qualification tests conducted at two different laser initiation pulses.

On the use of external burning to reduce aerospace vehicle transonic drag

NASA Technical Reports Server (NTRS)

Trefny, Charles J.

1990-01-01

The external combustion of hydrogen to reduce the transonic drag of aerospace vehicles is currently being investigated. A preliminary analysis based on a constant pressure control volume is discussed. Results indicate that the specific impulse of the external burning process rivals that of a turbojet and depends on the severity of the initial base drag as well as on the Mach flight number and the equivalence ratio. A test program was conducted to investigate hydrogen-air flame stability at the conditions of interest and to demonstrate drag reduction on a simple expansion ramp. Initial test results are presented and compared with the control-volume analysis. The expansion ramp surface pressure coefficient showed little variation with fuel pressure and altitude, in disagreement with the analysis. Flame stability results were encouraging and indicate that stable combustion is possible over an adequate range of conditions. Facility interference and chemical kinetics phenomena that make interpretation of subscale ground test data difficult are discussed.

Federating clinical data from six pediatric hospitals: process and initial results for microbiology from the PHIS+ consortium.

PubMed

Gouripeddi, Ramkiran; Warner, Phillip B; Mo, Peter; Levin, James E; Srivastava, Rajendu; Shah, Samir S; de Regt, David; Kirkendall, Eric; Bickel, Jonathan; Korgenski, E Kent; Precourt, Michelle; Stepanek, Richard L; Mitchell, Joyce A; Narus, Scott P; Keren, Ron

2012-01-01

Microbiology study results are necessary for conducting many comparative effectiveness research studies. Unlike core laboratory test results, microbiology results have a complex structure. Federating and integrating microbiology data from six disparate electronic medical record systems is challenging and requires a team of varied skills. The PHIS+ consortium which is partnership between members of the Pediatric Research in Inpatient Settings (PRIS) network, the Children's Hospital Association and the University of Utah, have used "FURTHeR' for federating laboratory data. We present our process and initial results for federating microbiology data from six pediatric hospitals.

Evaluation of Straight and Swept Ramp Obstacles on Enhancing Deflagration-to-Detonation Transition in Pulse Detonation Engines

DTIC Science & Technology

2006-12-01

models attempted to bracket the extremes of the conditions of interest. These conditions were Mach 2 and Mach 3 shocks , with initial medium...later, but all traces have been expanded to the area of interest. Pressure readings were primarily used to measure shock speeds, and initially used...results for the clean tube configuration. The characteristics of the initial shock are similar, and are comparable for all configurations tested

Ecodevelopmental Predictors of Early Initiation of Alcohol, Tobacco, and Drug Use Among Hispanic Adolescents

PubMed Central

Bacio, Guadalupe A.; Estrada, Yannine; Huang, Shi; Martínez, Marcos; Sardinas, Krystal; Prado, Guillermo

2015-01-01

The purpose of this cross-sectional study was to test the transactional relationships of risk and protective factors that influence initiation of alcohol, tobacco, and drug use among Hispanic youth. Ecodevelopmental theory was used to identify factors at multiple ecological levels with a focus on four school-level characteristics (i.e. school socioeconomic status, school climate, school acculturation, and school ethnic composition). A sample of 741 Hispanic adolescents (M age =13.9, SD =.67) and their caregivers were recruited from 18 participating middle schools in Miami-Dade County, FL. Structural equation modeling was used to test the hypothesized ecodevelopmental model of early substance use, accounting for school clustering effects. Results provided strong support for the model (CFI = .95; RMSEA =.03). School SES was indirectly related to the likelihood of starting to use substances through perceived peer use norms (β =.03, p <.02). Similarly, school climate had an indirect effect on substance use initiation through family functioning and perceptions of peer use norms (β = −.03, p < .01). Neither school ethnic composition nor school acculturation had indirect effects on initiation of substance use. Results highlight the importance of the interplay of risk and protective factors at multiple ecological levels that impact early substance use initiation. Further, findings underscore the key role of school level characteristics on initiation of substance use and present opportunities for intervention. PMID:26054814

Dieting and smoking initiation in early adolescent girls and boys: a prospective study.

PubMed Central

Austin, S B; Gortmaker, S L

2001-01-01

OBJECTIVES: This analysis tested the relation between dieting frequency and risk of smoking initiation in a longitudinal sample of adolescents. METHODS: From 1995 to 1997, 1295 middle school girls and boys participated in a nutrition and physical activity intervention study. The prospective association between dieting frequency at baseline and smoking initiation 2 years later was tested. RESULTS: Compared with girls who reported no dieting at baseline, girls who dieted up to once per week had 2 times the adjusted odds of becoming smokers (odds ratio = 2.0; 95% confidence interval = 1.1, 3.5), and girls who dieted more often had 4 times the adjusted odds of becoming smokers (odds ratio = 3.9; 95% confidence interval = 1.5, 10.4). CONCLUSIONS: Dieting among girls may exacerbate risk of initiating smoking, with increasing risk with greater dieting frequency. PMID:11236412

Analysis and testing of numerical formulas for the initial value problem

NASA Technical Reports Server (NTRS)

Brown, R. L.; Kovach, K. R.; Popyack, J. L.

1980-01-01

Three computer programs for evaluating and testing numerical integration formulas used with fixed stepsize programs to solve initial value systems of ordinary differential equations are described. A program written in PASCAL SERIES, takes as input the differential equations and produces a FORTRAN subroutine for the derivatives of the system and for computing the actual solution through recursive power series techniques. Both of these are used by STAN, a FORTRAN program that interactively displays a discrete analog of the Liapunov stability region of any two dimensional subspace of the system. The derivatives may be used by CLMP, a FORTRAN program, to test the fixed stepsize formula against a good numerical result and interactively display the solutions.

Initiation and growth of multiple-site damage in the riveted lap joint of a curved stiffened fuselage panel: An experimental and analytical study

NASA Astrophysics Data System (ADS)

Ahmed, Abubaker Ali

As part of the structural integrity research of the National Aging Aircraft Research Program, a comprehensive study on multiple-site damage (MSD) initiation and growth in a pristine lap-joint fuselage panel has been conducted. The curved stiffened fuselage panel was tested at the Full-Scale Aircraft Structural Test Evaluation and Research (FASTER) facility located at the Federal Aviation Administration William J. Hughes Technical Center. A strain survey test was conducted to verify proper load application. The panel was then subjected to a fatigue test with constant-amplitude cyclic loading. The applied loading spectrum included underload marker cycles so that crack growth history could be reconstructed from post-test fractographic examinations. Crack formation and growth were monitored via nondestructive and high-magnification visual inspections. Strain gage measurements recorded during the strain survey tests indicated that the inner surface of the skin along the upper rivet row of the lap joint experienced high tensile stresses due to local bending. During the fatigue loading, cracks were detected by eddy-current inspections at multiple rivet holes along the upper rivet row. Through-thickness cracks were detected visually after about 80% of the fatigue life. Once MSD cracks from two adjacent rivet holes linked up, there was a quick deterioration in the structural integrity of the lap joint. The linkup resulted in a 2.87" (72.9-mm) lead fatigue crack that rapidly propagated across 12 rivet holes and crossed over into the next skin bay, at which stage the fatigue test was terminated. A post-fatigue residual strength test was then conducted by loading the panel quasi-statically up to final failure. The panel failed catastrophically when the crack extended instantaneously across three additional bays. Post-test fractographic examinations of the fracture surfaces in the lap joint of the fuselage panel were conducted to characterize subsurface crack initiation and growth. Results showed evidence of fretting damage and crack initiation at multiple locations near the rivet holes along the faying surface of the skin. The subsurface cracks grew significantly along the faying surface before reaching the outer surface of the skin, forming elliptical crack fronts. A finite element model (FE) of the panel was constructed and geometrically-nonlinear analyses conducted to determine strain distribution under the applied loads. The FE model was validated by comparing the analysis results with the strain gage measurements recorded during the strain survey test. The validated FE model was then used to determine stress-intensity factors at the crack tips. Stress-intensity factor results indicated that crack growth in the lap joint was under mixed-mode; however, the opening-mode stress intensity factor was dominant. The stress-intensity factors computed from the FE analysis were used to conduct cycle-by-cycle integration of fatigue crack growth. In the cycle-by-cycle integration, the NASGRO crack growth model was used with its parameters selected to account for the effects of plasticity-induced crack closure and the test environment on crack growth rate. Fatigue crack growth predictions from cycle-by-cycle computation were in good agreement with the experimental measured crack growth data. The results of the study provide key insights into the natural development and growth of MSD cracks in the pristine lap joint. The data provided by the study represent a valuable source for the evaluation and validation of analytical methodologies used for predicting MSD crack initiation and growth.

Aperture Valve for the Mars Organic Molecule Analyzer (MOMA)

NASA Technical Reports Server (NTRS)

Engler, Charles; Canham, John

2014-01-01

NASA's participation in the multi-nation ExoMars 2018 Rover mission includes a critical astrobiology Mass Spectrometer Instrument on the Rover called the Mars Organic Molecule Analyzer (MOMA). The Aperture Valve is a critical electromechanical valve used by the Mass Spectrometer to facilitate the transfer of ions from Martian soil to the Mass Spectrometer for analysis. The MOMA Aperture Valve development program will be discussed in terms of the initial valve design and subsequent improvements that resulted from prototype testing. The initial Aperture Valve concept seemed promising, based on calculations and perceived merits. However, performance results of this design were disappointing, due to delamination of TiN and DLC coatings applied to the titanium base metals, causing debris from the coatings to seize the valve. While peer reviews and design trade studies are important forums to vet a concept design, results from testing should not be underestimated. Despite the lack of development progress to meet requirements, valuable information from weakness discovered in the initial Valve design was used to develop a second, more robust Aperture Valve. Based on a check-ball design, the ETU / flight valve design resulted in significantly less surface area to create the seal. Moreover, PVD coatings were eliminated in favor of hardened, non-magnetic corrosion resistant alloys. Test results were impressive, with the valve achieving five orders of magnitude better sealing leak rate over end of life requirements. Cycle life was equally impressive, achieving 280,000 cycles without failure.

Aperture Valve for the Mars Organic Molecule Analyzer (MOMA)

NASA Technical Reports Server (NTRS)

Hakun, Claef F.; Engler, Charles D.; Barber, Willie E.; Canham, John S.

2014-01-01

NASA's participation in the multi-nation ExoMars 2018 Rover mission includes a critical astrobiology Mass Spectrometer Instrument on the Rover called the Mars Organic Molecule Analyzer (MOMA). The Aperture Valve is a critical electromechanical valve used by the Mass Spectrometer to facilitate the transfer of ions from Martian soil to the Mass Spectrometer for analysis. The MOMA Aperture Valve development program will be discussed in terms of the Initial valve design and subsequent improvements that resulted from prototype testing. The Initial Aperture Valve concept seemed promising, based on calculations and perceived merits. However, performance results of this design were disappointing, due to delamination of TiN and DLC coatings applied to the Titanium base metals, causing debris from the coatings to seize the valve. While peer reviews and design trade studies are important forums to vet a concept design, results from testing should not be underestimated.Despite the lack of development progress to meet requirements, valuable information from weakness discovered in the Initial Valve design was used to develop a second, more robust Aperture valve. Based on a check-ball design, the ETU flight valve design resulted in significantly less surface area to create the seal. Moreover, PVD coatings were eliminated in favor of hardened, nonmagnetic corrosion resistant alloys. Test results were impressive, with the valve achieving five orders of magnitude better sealing leak rate over end of life requirements. Cycle life was equally impressive, achieving 280,000 cycles without failure.

Aperture Valve for the Mars Organic Molecule Analyzer (MOMA)

NASA Technical Reports Server (NTRS)

Engler, Charles D.; Canham, John S.

2014-01-01

NASA's participation in the multi-nation ExoMars 2018 Rover mission includes a critical astrobiology Mass Spectrometer Instrument on the Rover called the Mars Organic Molecule Analyzer (MOMA). The Aperture Valve is a critical electromechanical valve used by the Mass Spectrometer to facilitate the transfer of ions from Martian soil to the Mass Spectrometer for analysis. The MOMA Aperture Valve development program will be discussed in terms of the Initial valve design and subsequent improvements that resulted from prototype testing. The Initial Aperture Valve concept seemed promising, based on calculations and perceived merits. However, performance results of this design were disappointing, due to delamination of TiN and DLC coatings applied to the Titanium base metals, causing debris from the coatings to seize the valve. While peer reviews and design trade studies are important forums to vet a concept design, results from testing should not be underestimated. Despite the lack of development progress to meet requirements, valuable information from weakness discovered in the Initial Valve design was used to develop a second, more robust Aperture valve. Based on a check-ball design, the ETU /flight valve design resulted in significantly less surface area to create the seal. Moreover, PVD coatings were eliminated in favor of hardened, nonmagnetic corrosion resistant alloys. Test results were impressive, with the valve achieving five orders of magnitude better sealing leak rate over end of life requirements. Cycle life was equally impressive, achieving 280,000 cycles without failure.

Asthma in pregnancy: association between the Asthma Control Test and the Global Initiative for Asthma classification and comparisons with spirometry.

PubMed

de Araujo, Georgia Véras; Leite, Débora F B; Rizzo, José A; Sarinho, Emanuel S C

2016-08-01

The aim of this study was to identify a possible association between the assessment of clinical asthma control using the Asthma Control Test (ACT) and the Global Initiative for Asthma (GINA) classification and to perform comparisons with values of spirometry. Through this cross-sectional study, 103 pregnant women with asthma were assessed in the period from October 2010 to October 2013 in the asthma pregnancy clinic at the Clinical Hospital of the Federal University of Pernambuco. Questionnaires concerning the level of asthma control were administered using the Global Initiative for Asthma classification, the Asthma Control Test validated for asthmatic expectant mothers and spirometry; all three methods of assessing asthma control were performed during the same visit between the twenty-first and twenty-seventh weeks of pregnancy. There was a significant association between clinical asthma control assessment using the Asthma Control Test and the Global Initiative for Asthma classification (p<0.001). There were also significant associations between the results of the subjective instruments of asthma (the GINA classification and the ACT) and evidence of lung function by spirometry. This study shows that both the Global Initiative for Asthma classification and the Asthma Control Test can be used for asthmatic expectant mothers to assess the clinical control of asthma, especially at the end of the second trimester, which is assumed to be the period of worsening asthma exacerbations during pregnancy. We highlight the importance of the Asthma Control Test as a subjective instrument with easy application, easy interpretation and good reproducibility that does not require spirometry to assess the level of asthma control and can be used in the primary care of asthmatic expectant mothers. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Failure to obtain value enhancement by within-trial contrast in simultaneous and successive discriminations.

PubMed

Arantes, Joana; Grace, Randolph C

2008-02-01

The present research tested the generality of the "work ethic" effect described by Clement, Feltus, Kaiser, and Zentall (2000). In Experiment 1, we trained 10 pigeons on a pair of either simultaneous or successive discriminations. One discrimination followed a high-effort requirement (20 pecks to the center key) and the other followed a low-effort requirement (1 peck). Contrary to Clement et al.'s results, we found that preferences between the S+ and S- stimuli in transfer tests depended on the event that initiated the trial: Pigeons preferred the stimulus from the baseline discrimination whose initiating event was most dissimilar from that preceding the test trial. Preferences were similar but less extreme in the successive condition. In Experiment 2, we investigated whether test preferences depended on the amount of training. A total of 12 pigeons were trained on a pair of simultaneous discriminations, except that test sessions were scheduled after every three baseline sessions. Preferences increased across test sessions but were similar to those in Experiment 1. Together with Vasconcelos, Urcuioli, and Lionello-DeNolf (2007a), our study represents a second failure to replicate Clement et al.'s work ethic effect. The finding that preference depends on the event that initiates the test trial suggests that choice probes may not provide unambiguous assessments of stimulus value.

Loss to Follow-Up from HIV Screening to ART Initiation in Rural China.

PubMed

Gu, Diane; Mao, Yurong; Tang, Zhenzhu; Montaner, Julio; Shen, Zhiyong; Zhu, Qiuying; Detels, Roger; Jin, Xia; Xiong, Ran; Xu, Juan; Ling, Walter; Erinoff, Lynda; Lindblad, Robert; Liu, David; Van Veldhuisen, Paul; Hasson, Albert; Wu, Zunyou

2016-01-01

Patients who are newly screened HIV positive by EIA are lost to follow-up due to complicated HIV testing procedures. Because this is the first step in care, it affects the entire continuum of care. This is a particular concern in rural China. To assess the routine HIV testing completeness and treatment initiation rates at 18 county-level general hospitals in rural Guangxi. We reviewed original hospital HIV screening records. Investigators also engaged with hospital leaders and key personnel involved in HIV prevention activities to characterize in detail the routine care practices in place at each county. 699 newly screened HIV-positive patients between January 1 and June 30, 2013 across the 18 hospitals were included in the study. The proportion of confirmatory testing across the 18 hospitals ranged from 14% to 87% (mean of 43%), and the proportion of newly diagnosed individuals successfully initiated antiretroviral treatment across the hospitals ranged from 3% to 67% (mean of 23%). The average interval within hospitals for individuals to receive the Western Blot (WB) and CD4 test results from HIV positive screening (i.e. achieving testing completion) ranged from 14-116 days (mean of 41.7 days) across the hospitals. The shortest interval from receiving a positive EIA screening test result to receiving WB and CD4 testing and counseling was 0 day and the longest was 260 days. The proportion of patients newly screened HIV positive that completed the necessary testing procedures for HIV confirmation and received ART was very low. Interventions are urgently needed to remove barriers so that HIV patients can have timely access to HIV/AIDS treatment and care in rural China.

Restructurable VLSI Program

DTIC Science & Technology

1981-03-31

logic testing element and a concomitant testability criterion ideally suited to dynamic circuit applications and appro- priate for automatic computer...making connections automatically . PF is an experimental feature which provides users with only four different chip sizes (full, half, quarter, and eighth...initial solution is found constructively which is improved by pair-wise swapping. Results show, however, that the constructive initial sorter , which

Measuring Quality beyond Test Scores: The Impact of Regional Context on Curriculum Implementation (in Northern Uganda)

ERIC Educational Resources Information Center

Spreen, Carol Anne; Knapczyk, Jillian J.

2017-01-01

Although global initiatives have brought attention to the lack of quality in education systems worldwide; the question remains, how do we implement quality education? Teachers, a vital component of the education process, are not usually included in these global conversations; this results in government initiatives missing key obstacles faced by…

Experimental Estimates of the Impacts of Class Size on Test Scores: Robustness and Heterogeneity

ERIC Educational Resources Information Center

Ding, Weili; Lehrer, Steven F.

2011-01-01

Proponents of class size reductions (CSRs) draw heavily on the results from Project Student/Teacher Achievement Ratio to support their initiatives. Adding to the political appeal of these initiative are reports that minority and economically disadvantaged students received the largest benefits from smaller classes. We extend this research in two…

Develop and test fuel cell powered on-site integrated total energy system

NASA Technical Reports Server (NTRS)

1983-01-01

Test results are given for a 5 kW stack and initial results for an integrated, grid connected system operating from methanol fuel. Site selection criteria are presented for future demonstration of a 50 or 100 kW OS/IES. Preliminary results are also given with approximate internal rates of return to the building owner. Progress in development and construction of a 50 kW modular methanol/steam reformer is reported.

Care initiation area yields dramatic results.

PubMed

2009-03-01

The ED at Gaston Memorial Hospital in Gastonia, NC, has achieved dramatic results in key department metrics with a Care Initiation Area (CIA) and a physician in triage. Here's how the ED arrived at this winning solution: Leadership was trained in and implemented the Kaizen method, which eliminates redundant or inefficient process steps. Simulation software helped determine additional space needed by analyzing arrival patterns and other key data. After only two days of meetings, new ideas were implemented and tested.

Azathioprine Intolerance in Japanese Patients with Antineutrophil Cytoplasmic Antibody-associated Vasculitis

PubMed Central

Morishita, Michiko; Watanabe, Haruki; Yan, Minglu; Zeggar, Sonia; Hiramatsu, Sumie; Ohashi, Keiji; Miyawaki, Yoshia; Katsuyama, Eri; Katsuyama, Takayuki; Takano Narazaki, Mariko; Toyota Tatebe, Noriko; Sunahori Watanabe, Katsue; Kawabata, Tomoko; Sada, Ken-Ei; Wada, Jun

2017-01-01

Objective To assess the safety of azathioprine (AZA) in Japanese patients with antineutrophil cytoplasmic antibody-associated vasculitis (AAV). Methods We retrospectively enrolled 67 consecutive AAV patients who had initiated AZA treatment from January 2006 to August 2014 at Okayama University Hospital. We evaluated the development of severe adverse events (AEs), AZA discontinuation due to total AEs (severe AEs included) within 1 year, and AZA-associated risk factors. Results The patients' median age was 70 years old. Forty-nine women and 18 men participated at the initiation of the study. Fifty-eight (87%) patients experienced AEs, and 36 experienced severe AEs (21 hepatic and 11 cytopenic severe AEs). Thirty-one (46%) patients discontinued treatment because of AEs. Abnormal hepatic laboratory test results at the treatment initiation were more frequent in patients with hepatic severe AEs and were associated with treatment discontinuation. The leukocyte and neutrophil counts at the treatment initiation were lower in the patients who discontinued treatment because of cytopenic AEs than in those who continued treatment. Only two patients experienced flare-ups during treatment. Conclusion The AE-associated AZA discontinuation rate in Japanese AAV patients was relatively high. AZA use warrants caution in patients with abnormal hepatic laboratory test results or low leukocyte or neutrophil counts. PMID:28674351

Initial retrieval shields against retrieval-induced forgetting

PubMed Central

Racsmány, Mihály; Keresztes, Attila

2015-01-01

Testing, as a form of retrieval, can enhance learning but it can also induce forgetting of related memories, a phenomenon known as retrieval-induced forgetting (RIF). In four experiments we explored whether selective retrieval and selective restudy of target memories induce forgetting of related memories with or without initial retrieval of the entire learning set. In Experiment 1, subjects studied category-exemplar associations, some of which were then either restudied or retrieved. RIF occurred on a delayed final test only when memories were retrieved and not when they were restudied. In Experiment 2, following the study phase of category-exemplar associations, subjects attempted to recall all category-exemplar associations, then they selectively retrieved or restudied some of the exemplars. We found that, despite the huge impact on practiced items, selective retrieval/restudy caused no decrease in final recall of related items. In Experiment 3, we replicated the main result of Experiment 2 by manipulating initial retrieval as a within-subject variable. In Experiment 4 we replicated the main results of the previous experiments with non-practiced (Nrp) baseline items. These findings suggest that initial retrieval of the learning set shields against the forgetting effect of later selective retrieval. Together, our results support the context shift theory of RIF. PMID:26052293

Effect of eccentric exercise program for early tibialis posterior tendinopathy.

PubMed

Kulig, Kornelia; Lederhaus, Eric S; Reischl, Steve; Arya, Shruti; Bashford, Greg

2009-09-01

Morphology and vascularization of painful tibialis posterior (TP) tendons before and after an intervention targeting the degenerated tendon were examined. Functional status and pain level were also assessed. A10-week twice daily, progressive eccentric tendon loading, calf stretching program with orthoses was implemented with ten, early stage TP tendinopathy subjects. TP tendons were imaged by grayscale and Doppler ultrasound at INITIAL and POST evaluations to assess the tendon's morphology and signs of neovascularization. The Foot Functional Index (FFI), Physical Activity Scale (PAS), 5-Minute Walk Test, and single heel raise (SHR) test were completed at INITIAL and POST evaluations. The Global Rating Scale (GRS) was completed at 6 months followup. One-way ANOVA was used to compare the FFI at INITIAL, POST, and 6-MONTH time points. Paired t-tests were used to compare means between the remaining variables. The level of significance was p = 0.05. There was a significant difference in FFI total, pain, and disability at the three time-points. Post-hoc paired t-tests revealed that the FFI scores were lower for the total score and pain and disability subcategories when comparing from INITIAL to POST and INITIAL to 6-MONTH evaluations (p < 0.05 for all). The number of SHR increased significantly on the involved side from INITIAL to POST evaluation (p = 0.041). The GRS demonstrated minimum clinically important differences for improvements in symptoms at 6-MONTH. Tendon morphology and vascularization remained abnormal following the intervention. A 10-week tendon specific eccentric program resulted in improvements in symptoms and function without changes in tendon morphology or neovascularization.

SmartPark Truck Parking Availability System: Magnetometer Technology Field Operational Test Results

DOT National Transportation Integrated Search

2011-01-01

The purpose of FMCSAs SmartPark initiative is to determine the feasibility of a technology for providing truck parking space availability in real time to truckers on the road. SmartPark consists of two phases. Phase I was a field operational test ...

Development Of Performance Specifications For Collision Avoidance Systems For Lane Change, Merging, And Backing, Task 3 - Interim Report: Test Of Existing Hardware

DOT National Transportation Integrated Search

1995-05-01

KEYWORDS : ADVANCED VEHICLE CONTROL & SAFETY SYSTEMS OR AVCSS, COLLISION WARNING/AVOIDANCE SYSTEMS, CRASH REDUCTION, INTELLIGENT VEHICLE INITIATIVE OR IVI : RESULTS FROM THE TESTING OF ELEVEN COLLISION AVOIDANCE SYSTEMS (CAS) FOR LANE CHANGE, ...

SmartPark Truck Parking Availability System: Video Technology Field Operational Test Results

DOT National Transportation Integrated Search

2011-01-01

The purpose of FMCSAs SmartPark initiative is to determine the feasibility of a technology for providing truck parking space availability in real time to truckers on the road. SmartPark consists of two phases. Phase I was a field operational test ...

Meta-Evaluation Applied To Results Of ITS Initiatives

DOT National Transportation Integrated Search

1995-04-01

META-EVALUATION : META-EVALUATION IS A PROCESS TO BE USED FOR THE COMPARISON OF RESULTS ACROSS INTELLIGENT TRANSPORTATION SYSTEMS (ITS). OPERATIONAL TESTS, A COMPONENT OF THE ITS PROGRAM ADMINISTERED BY THE FEDERAL HIGHWAY ADMINISTRATION (FHWA), A...

Evaluation of Pharmacist Impact on Culture Review Process for Patients Discharged From the Emergency Department.

PubMed

Santiago, Ruben D; Bazan, Jose A; Brown, Nicole V; Adkins, Eric J; Shirk, Mary Beth

2016-10-01

Background: Accurate and timely review of microbiological test results is a core component of antimicrobial stewardship. There is documented success of these programs in the inpatient setting; however, emergency department (ED) patients are typically not included in these initiatives. Objectives: To assess the impact of an emergency medicine pharmacist (EMP)-facilitated review process of positive microbiological test results from patients discharged from the ED as measured by time to positive result review and number of indicated interventions completed. Methods: This was a retrospective study that compared EMP-facilitated to ED charge nurse (CN)-facilitated physician review of randomly selected positive microbiological test results. Groups were compared concurrently within the time frame of July 1, 2012 through December 31, 2012. Results: One hundred seventy-eight positive microbiological test results were included (EMP, n = 91; CN, n = 87). The median (IQR) time to initial review was 3 (1.0-6.3) hours for the EMP and 2 (0.3-5.5) hours for the CN group ( p = .35). Four percent (1/25) of indicated interventions were not completed in the EMP group versus 47% (14/30) in the CN group ( p = .0004). Conclusion: An EMP was significantly less likely to miss an intervention when indicated with no difference in time to review of positive microbiological results. These findings support the role of the EMP in antimicrobial stewardship in the ED.

40 CFR 60.4400 - How do I conduct the initial and subsequent performance tests, regarding NOX?

Code of Federal Regulations, 2010 CFR

2010-07-01

... subsequent performance tests, regarding NOX? 60.4400 Section 60.4400 Protection of Environment ENVIRONMENTAL... Standards of Performance for Stationary Combustion Turbines Performance Tests § 60.4400 How do I conduct the initial and subsequent performance tests, regarding NOX? (a) You must conduct an initial performance test...

40 CFR 60.4400 - How do I conduct the initial and subsequent performance tests, regarding NOX?

Code of Federal Regulations, 2013 CFR

2013-07-01

... subsequent performance tests, regarding NOX? 60.4400 Section 60.4400 Protection of Environment ENVIRONMENTAL... Standards of Performance for Stationary Combustion Turbines Performance Tests § 60.4400 How do I conduct the initial and subsequent performance tests, regarding NOX? (a) You must conduct an initial performance test...

40 CFR 60.4400 - How do I conduct the initial and subsequent performance tests, regarding NOX?

Code of Federal Regulations, 2011 CFR

2011-07-01

... subsequent performance tests, regarding NOX? 60.4400 Section 60.4400 Protection of Environment ENVIRONMENTAL... Standards of Performance for Stationary Combustion Turbines Performance Tests § 60.4400 How do I conduct the initial and subsequent performance tests, regarding NOX? (a) You must conduct an initial performance test...

40 CFR 60.4400 - How do I conduct the initial and subsequent performance tests, regarding NOX?

Code of Federal Regulations, 2012 CFR

2012-07-01

... subsequent performance tests, regarding NOX? 60.4400 Section 60.4400 Protection of Environment ENVIRONMENTAL... Standards of Performance for Stationary Combustion Turbines Performance Tests § 60.4400 How do I conduct the initial and subsequent performance tests, regarding NOX? (a) You must conduct an initial performance test...

40 CFR 60.4400 - How do I conduct the initial and subsequent performance tests, regarding NOX?

Code of Federal Regulations, 2014 CFR

2014-07-01

... subsequent performance tests, regarding NOX? 60.4400 Section 60.4400 Protection of Environment ENVIRONMENTAL... Standards of Performance for Stationary Combustion Turbines Performance Tests § 60.4400 How do I conduct the initial and subsequent performance tests, regarding NOX? (a) You must conduct an initial performance test...

Qualification of CASMO5 / SIMULATE-3K against the SPERT-III E-core cold start-up experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grandi, G.; Moberg, L.

SIMULATE-3K is a three-dimensional kinetic code applicable to LWR Reactivity Initiated Accidents. S3K has been used to calculate several international recognized benchmarks. However, the feedback models in the benchmark exercises are different from the feedback models that SIMULATE-3K uses for LWR reactors. For this reason, it is worth comparing the SIMULATE-3K capabilities for Reactivity Initiated Accidents against kinetic experiments. The Special Power Excursion Reactor Test III was a pressurized-water, nuclear-research facility constructed to analyze the reactor kinetic behavior under initial conditions similar to those of commercial LWRs. The SPERT III E-core resembles a PWR in terms of fuel type, moderator,more » coolant flow rate, and system pressure. The initial test conditions (power, core flow, system pressure, core inlet temperature) are representative of cold start-up, hot start-up, hot standby, and hot full power. The qualification of S3K against the SPERT III E-core measurements is an ongoing work at Studsvik. In this paper, the results for the 30 cold start-up tests are presented. The results show good agreement with the experiments for the reactivity initiated accident main parameters: peak power, energy release and compensated reactivity. Predicted and measured peak powers differ at most by 13%. Measured and predicted reactivity compensations at the time of the peak power differ less than 0.01 $. Predicted and measured energy release differ at most by 13%. All differences are within the experimental uncertainty. (authors)« less

Construction and Initial Tests of MAIZE: 1 MA LTD-Driven Z-Pinch *

NASA Astrophysics Data System (ADS)

Gilgenbach, R. M.; Gomez, M. R.; Zier, J. C.; Tang, W.; French, D. M.; Lau, Y. Y.; Mazarakis, M. G.; Cuneo, M. E.; Johnston, M. D.; Oliver, B. V.; Mehlhorn, T. A.; Kim, A. A.; Sinebryukhov, V. A.

2008-11-01

We report construction and initial testing of a 1-MA Linear Transformer Driver (LTD), The Michigan Accelerator for Inductive Z-pinch Experiments, (MAIZE). This machine, the first of its type to reach the USA, is based on the joint HCEI, Sandia Laboratories, and UM development effort. The compact LTD uses 80 capacitors and 40 spark gap switches, in 40 ``bricks'', to deliver 1 MA, 100 kV pulses with 70 ns risetime into a matched resistive load. Test results will be presented for a single brick and the full LTD. Design and construction will be presented of a low-inductance MITL. Experimental research programs under design and construction at UM include: a) Studies of Magneto-Raleigh-Taylor Instability of planar foils, and b) Vacuum convolute studies including cathode and anode plasma. Theory and simulation results will be presented for these planned experiments. Initial experimental designs and moderate-current feasibility experiments will be discussed. *Research supported by U. S. DoE through Sandia National Laboratories award document numbers 240985, 768225, 790791 and 805234 to the UM. MRG supported by NNSA Fellowship and JCZ supported by NPSC Fellowship / Sandia National Labs.

The influence of total suction on the brittle failure characteristics of clay shales

NASA Astrophysics Data System (ADS)

Amann, F.; Linda, W.; Zimmer, S.; Thoeny, R.

2013-12-01

Clay shale testing is challenging and the results obtained from standard laboratory tests may not always reflect the strength of the clay shale in-situ. This is to a certain extend associated with the sensitivity of these rock types to desaturation processes during drilling, sample storage, and sample preparation. In this study the relationship between total suction, uniaxial compressive strength and Brazilian tensile (BTS) strength of cylindrical samples of Opalinus Clay was established in a systematic manner. Unconfined uniaxial compression and BTS tests were performed utilizing a servo-controlled testing procedure. Total suctions in the specimens was generated in air tight desiccators using supersaturated saline solutions which establish a relative humidity ranging from 20% to 99%. For unconfined compressive strength tests loading of the specimens occurred parallel to bedding. For BTS tests loading was either oriented normal or perpendicular to bedding. Both, the crack initiation and volumetric strain reversal threshold values were determined using volumetric and radial stress-strain methods. The results of BTS tests show that the tensile strength normal and perpendicular to bedding increases by a factor of approximately 3 when total suction is increased from 0 to 90 MPa (i.e. saturation decreases from 1.0 to 0.7) . Beyond 90 MPa total suction no further increase in tensile strength was observed, most probably due to shrinkage cracks which alter the tensile strength of the clay shale. Results obtained from UCS tests suggest that higher total suctions result in higher UCS values. Between total suctions of 0 to 90 MPa, the strength increase is almost linear (i.e. the UCS increases by a factor of 1.5 MPa). Beyond 90 MPa total suction no further strength increase was observed. A similar trend can be observed for crack initiation and crack damage values. In the same range of total suction the crack initiation stress increases by a factor of 5 (from 2 MPa to 10 MPa), and the crack damage stress increases by a factor of 2 (from 6 to 12 MPa). In addition to UCS tests, the water retention curve of intact and disturbed specimens was established. Here, results indicate that the drying path remains nearly unaffected by mechanical damage. However, the wetting path is considerably affected by mechanical damage.

Use of the Marshall Space Flight Center solar simulator in collector performance evaluation

NASA Technical Reports Server (NTRS)

Humphries, W. R.

1978-01-01

Actual measured values from simulator checkout tests are detailed. Problems encountered during initial startup are discussed and solutions described. Techniques utilized to evaluate collector performance from simulator test data are given. Performance data generated in the simulator are compared to equivalent data generated during natural outdoor testing. Finally, a summary of collector performance parameters generated to date as a result of simulator testing are given.

Equipment. [for testing human space perception

NASA Technical Reports Server (NTRS)

1974-01-01

A discussion is presented on the problems encountered in designing and constructing a simulator to determine human vestibular response to a range of linear accelerations from 0 to 0.3 g's. Starting with a set of initial performance specifications, the designers combined an array of commercially available components into a system which, altough requiring further refinement before completion, shows considerable promise of fulfilling the initial requirements. The resulting system consists of a wheeled vehicle driven by a cable and drum arrangement, powered by a hydraulic-electric servo-valve. Technical design considerations are presented along with a discussion of the trade-offs between various component options. A description of the system characteristics as well as an analysis of preliminary test results and recommendations for future system improvements are included.

40 CFR 63.6610 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2010 CFR

2010-07-01

... initial performance tests or other initial compliance demonstrations if I own or operate a stationary RICE... performance tests or other initial compliance demonstrations if I own or operate a stationary RICE with a site... stationary RICE with a site rating of more than 500 brake HP located at a major source of HAP emissions you...

40 CFR 63.6610 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2011 CFR

2011-07-01

... initial performance tests or other initial compliance demonstrations if I own or operate a stationary RICE... performance tests or other initial compliance demonstrations if I own or operate a stationary RICE with a site... stationary RICE with a site rating of more than 500 brake HP located at a major source of HAP emissions you...

Multiplex method for initial complex testing of antibodies to blood transmitted diseases agents.

PubMed

Poltavchenko, Alexander G; Nechitaylo, Oleg V; Filatov, Pavel V; Ersh, Anna V; Gureyev, Vadim N

2016-10-01

Initial screening of donors and population at high risk of infection with blood transmitted diseases involves a number of analyses using monospesific diagnostic systems, and therefore is expensive labor- and time-consuming process. The goal of this work is to construct a multiplex test enabling to carry out rapid initial complex testing at a low price. The paper describes a kit making it possible to detect simultaneously antibodies to six agents of the most significant blood transmitted diseases: HIV virus, hepatitis B and C viruses, cytomegalovirus, T. pallidum and T. gondii in blood products. The kit comprises multiplex dot-immunoassay based on plane protein arrays (immune chips) using colloidal gold conjugates and silver development. It provides an opportunity to carry out complex analysis within 70min at room temperature, and there is no need of well-qualified personnel. We compared laboratory findings of the kit with monospecific kits for ELISA produced by two Russian commercial companies. Dot-assay results correlate well with data obtained using commercial kits for ELISA. Furthermore, multiplex analysis is quicker and cheaper in comparison with ELISA and can be carried out in non-laboratory conditions. The kit for multiplex dot-immunoassay of antibodies to blood transmitted agents can significantly simplify initial complex testing. Copyright © 2016 Elsevier B.V. All rights reserved.

Sweat chloride concentrations in children with Idiopathic Nephrotic Syndrome.

PubMed

Guglani, Lokesh; Moir, Devin; Jain, Amrish

2016-01-01

Idiopathic Nephrotic Syndrome (INS) has been believed to cause a false positive elevation of sweat chloride concentrations, as measured by the sweat test. Sweat tests were done for 11 children with acute onset INS at admission and again while they were in remission, with results being compared to normal historical controls. The initial sweat chloride concentration for 10 patients was normal (mean16.7 ± 11.02 mmol/L) and 1 patient had inadequate collection. This latter patient and two others were excluded during follow-up because of diagnoses other than INS. Sweat test results for the eight INS patients during follow up remained unchanged when they were in remission (16.94 ± 7.88 mmol/L; P = 0.98; Wilcoxon Matched-Pairs Signed Rank Test). In comparing sweat chloride concentrations from INS patients to those from 20 historical control subjects, we found no significant differences (Mann-Whitney Test; initial vs. control P = 0.643; follow up vs. control P = 0.806). INS does not cause a false positive sweat test. Further studies should be done to objectively assess the conditions that have been reported to affect sweat chloride concentrations. © 2015 Wiley Periodicals, Inc.

Employability and personal initiative as antecedents of job satisfaction.

PubMed

Gamboa, Juan Pablo; Gracia, Francisco; Ripoll, Pilar; Peiró, José María

2009-11-01

In a changing and flexible labour market it is important to clarify the role of environmental and personal variables that contribute to obtaining adequate levels of job satisfaction. The aim of the present study is to analyze the direct effects of employability and personal initiative on intrinsic, extrinsic and social job satisfaction, clarifying their cumulative and interactive effects. The study has been carried out in a sample of 1319 young Spanish workers. Hypotheses were tested by means of the moderated hierarchical regression analysis. Results show that employability and personal initiative predict in a cumulative way the intrinsic, extrinsic and social job satisfaction. Moreover, the interaction between employability and personal initiative increases the prediction of these two variables on intrinsic and extrinsic job satisfaction. Results also indicate that higher values of employability when initiative is also high are associated to higher levels of intrinsic and extrinsic satisfaction. These results have implications for theory and practice in a context of new employment relations.

Back off! The effect of emotion on backward step initiation.

PubMed

Bouman, Daniëlle; Stins, John F

2018-02-01

The distance regulation (DR) hypothesis states that actors are inclined to increase their distance from an unpleasant stimulus. The current study investigated the relation between emotion and its effect on the control of backward step initiation, which constitutes an avoidance-like behavior. Participants stepped backward on a force plate in response to neutral, high-arousing pleasant and high-arousing unpleasant visual emotional stimuli. Gait initiation parameters and the results of an exploratory analysis of postural sway were compared across the emotion categories using significance testing and Bayesian statistics. Evidence was found that gait initiation parameters were largely unaffected by emotional conditions. In contrast, the exploratory analysis of postural immobility showed a significant effect: highly arousing stimuli (pleasant and unpleasant) resulted in more postural sway immediately preceding gait initiation compared to neutral stimuli. This suggests that arousal, rather than valence, affects pre-step sway. These results contradict the DR hypothesis, since avoidance gait-initiation in response to unpleasant stimuli was no different compared to pleasant stimuli. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Abnormal ovarian cancer screening test result: women's informational, psychological and practical needs.

PubMed

Ryan, Patricia Y; Graves, Kristi D; Pavlik, Edward J; Andrykowski, Michael A

2007-01-01

Considerable effort has been devoted to the identification of cost-effective approaches to screening for ovarian cancer (OC). Transvaginal ultrasound (TVS) is one such screening approach. Approximately 5-7% of routine TVS screening tests yield abnormal results. Some women experience significant distress after receipt of an abnormal TVS screening test. Four focus groups provided in-depth, qualitative data regarding the informational, psychological, and practical needs of women after the receipt of an abnormal TVS result. Through question and content analytic procedures, we identified four themes: anticipation, emotional response, role of the screening technician, and impact of prior cancer experiences. Results provide initial guidance toward development of interventions to promote adaptive responses after receipt of an abnormal cancer screening test result.

A novel orthoimage mosaic method using a weighted A∗ algorithm - Implementation and evaluation

NASA Astrophysics Data System (ADS)

Zheng, Maoteng; Xiong, Xiaodong; Zhu, Junfeng

2018-04-01

The implementation and evaluation of a weighted A∗ algorithm for orthoimage mosaic with UAV (Unmanned Aircraft Vehicle) imagery is proposed. The initial seam-line network is firstly generated by standard Voronoi Diagram algorithm; an edge diagram is generated based on DSM (Digital Surface Model) data; the vertices (conjunction nodes of seam-lines) of the initial network are relocated if they are on high objects (buildings, trees and other artificial structures); and the initial seam-lines are refined using the weighted A∗ algorithm based on the edge diagram and the relocated vertices. Our method was tested with three real UAV datasets. Two quantitative terms are introduced to evaluate the results of the proposed method. Preliminary results show that the method is suitable for regular and irregular aligned UAV images for most terrain types (flat or mountainous areas), and is better than the state-of-the-art method in both quality and efficiency based on the test datasets.

Playskin Lift: Development and Initial Testing of an Exoskeletal Garment to Assist Upper Extremity Mobility and Function.

PubMed

Lobo, Michele A; Koshy, John; Hall, Martha L; Erol, Ozan; Cao, Huantian; Buckley, Jenner M; Galloway, James C; Higginson, Jill

2016-03-01

A person's ability to move his or her arms against gravity is important for independent performance of critical activities of daily living and for exploration that facilitates early cognitive, language, social, and perceptual-motor development. Children with a variety of diagnoses have difficulty moving their arms against gravity. The purpose of this technical report is to detail the design process and initial testing of a novel exoskeletal garment, the Playskin Lift, that assists and encourages children to lift their arms against gravity. This report details the design theory and process, the device, and the results of field testing with a toddler with impaired upper extremity function due to arthrogryposis multiplex congenita. The Playskin Lift is an inexpensive (<$30 material costs), easy to use (5/5 rating), comfortable (5/5 rating), and attractive (4/5 rating) device. While wearing the device, the child was able to contact objects more often throughout an increased play space, to look at toys more while contacting them, and to perform more complex interactions with toys. This report details initial testing with one child. Future testing with more participants is recommended. These results suggest that by considering the broad needs of users, including cost, accessibility, comfort, aesthetics, and function, we can design inexpensive devices that families and clinicians can potentially fabricate in their own communities to improve function, participation, exploration, and learning for children with disabilities. © 2016 American Physical Therapy Association.

Dwell Notch Low Cycle Fatigue Behavior of a Powder Metallurgy Nickel Disk Alloy

NASA Technical Reports Server (NTRS)

Telesman, J.; Gabb, T. P.; Yamada, Y.; Ghosn, L. J.; Jayaraman, N.

2012-01-01

A study was conducted to determine the processes which govern dwell notch low cycle fatigue (NLCF) behavior of a powder metallurgy (P/M) ME3 disk superalloy. The emphasis was placed on the environmentally driven mechanisms which may embrittle the highly stressed notch surface regions and reduce NLCF life. In conjunction with the environmentally driven notch surface degradation processes, the visco-plastic driven mechanisms which can significantly change the notch root stresses were also considered. Dwell notch low cycle fatigue testing was performed in air and vacuum on a ME3 P/M disk alloy specimens heat treated using either a fast or a slow cooling rate from the solutioning treatment. It was shown that dwells at the minimum stress typically produced a greater life debit than the dwells applied at the maximum stress, especially for the slow cooled heat treatment. Two different environmentally driven failure mechanisms were identified as the root cause of early crack initiation in the min dwell tests. Both of these failure mechanisms produced mostly a transgranular crack initiation failure mode and yet still resulted in low NLCF fatigue lives. The lack of stress relaxation during the min dwell tests produced higher notch root stresses which caused early crack initiation and premature failure when combined with the environmentally driven surface degradation mechanisms. The importance of environmental degradation mechanisms was further highlighted by vacuum dwell NLCF tests which resulted in considerably longer NLCF lives, especially for the min dwell tests.

PROspective Multicenter Imaging Study for Evaluation of Chest Pain: Rationale and Design of the PROMISE Trial

PubMed Central

Douglas, Pamela S.; Hoffmann, Udo; Lee, Kerry L.; Mark, Daniel B.; Al-Khalidi, Hussein R.; Anstrom, Kevin; Dolor, Rowena J.; Kosinski, Andrzej; Krucoff, Mitchell W.; Mudrick, Daniel W.; Patel, Manesh R.; Picard, Michael H.; Udelson, James E.; Velazquez, Eric J.; Cooper, Lawton

2014-01-01

Background Suspected coronary artery disease (CAD) is one of the most common, potentially life threatening diagnostic problems clinicians encounter. However, no large outcome-based randomized trials have been performed to guide the selection of diagnostic strategies for these patients. Methods The PROMISE study is a prospective, randomized trial comparing the effectiveness of two initial diagnostic strategies in patients with symptoms suspicious for CAD. Patients are randomized to either: 1) functional testing (exercise electrocardiogram, stress nuclear imaging, or stress echocardiogram); or 2) anatomic testing with >=64 slice multidetector coronary computed tomographic angiography. Tests are interpreted locally in real time by subspecialty certified physicians and all subsequent care decisions are made by the clinical care team. Sites are provided results of central core lab quality and completeness assessment. All subjects are followed for ≥1 year. The primary end-point is the time to occurrence of the composite of death, myocardial infarction, major procedural complications (stroke, major bleeding, anaphylaxis and renal failure) or hospitalization for unstable angina. Results Over 10,000 symptomatic subjects were randomized in 3.2 years at 193 US and Canadian cardiology, radiology, primary care, urgent care and anesthesiology sites. Conclusion Multi-specialty community practice enrollment into a large pragmatic trial of diagnostic testing strategies is both feasible and efficient. PROMISE will compare the clinical effectiveness of an initial strategy of functional testing against an initial strategy of anatomic testing in symptomatic patients with suspected CAD. Quality of life, resource use, cost effectiveness and radiation exposure will be assessed. Clinical trials.gov identifier NCT01174550 PMID:24890527

40 CFR 63.4312 - What records must I keep?

Code of Federal Regulations, 2010 CFR

2010-07-01

... based on testing, you must keep the summary sheet of results provided to you by the manufacturer or... and printing materials. If you conducted testing to determine mass fraction of organic HAP of coating... operated within the operating scenarios used to demonstrate initial compliance, documentation that affected...

40 CFR 63.7520 - What stack tests and procedures must I use?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Institutional Boilers and Process Heaters Testing, Fuel Analyses, and Initial Compliance Requirements § 63.7520... representative operating load conditions while burning the type of fuel or mixture of fuels that has the highest... measured hydrogen chloride concentrations, and the measured mercury concentrations that result from the...

Binary Colloidal Alloy Test-5: Aspheres

NASA Technical Reports Server (NTRS)

Chaikin, Paul M.; Hollingsworth, Andrew D.

2008-01-01

The Binary Colloidal Alloy Test - 5: Aspheres (BCAT-5-Aspheres) experiment photographs initially randomized colloidal samples (tiny nanoscale spheres suspended in liquid) in microgravity to determine their resulting structure over time. BCAT-5-Aspheres will study the properties of concentrated systems of small particles when they are identical, but not spherical in microgravity..

40 CFR 1033.320 - Calculation and reporting of test results.

Code of Federal Regulations, 2010 CFR

2010-07-01

... applicable non-deterioration adjustments such as a Green Engine Factor or regeneration adjustment factor... following are true: (1) The catalyst was in a green condition when tested initially. (2) The locomotive met... locomotive, including: (A) Configuration and engine family identification. (B) Year, make, and build date. (C...

Fostering Reading Excellence at Every Level of School through Reading Clinics

ERIC Educational Resources Information Center

Ortlieb, Evan; Grandstaff-Beckers, Gerlinde; Cheek, Earl H., Jr.

2012-01-01

With the increased emphasis on standardized testing from state and federal mandates, the need for reading remediation has intensified. Programs directed toward increasing student test scores have been put in place nationwide with mixed results. These initiatives include response to intervention (RTI), direct instruction, and individualized…

INITIAL TEST RESULTS OF THE LIMESTONE INJECTION MULTISTAGE BURNER (LIMB) DEMONSTRATION PROJECT

EPA Science Inventory

The paper discusses SO2 removal efficiency and low-NOx burner performance obtained during short term tests, as well as the impact of LIMB ash on electrostatic precipitator (ESP) performance at Ohio Edison's Edgewater Station. Project goals are to demonstrate 50% or more SO2 remov...

A Curriculum for Preparing Science Teachers to Use Microcomputers.

ERIC Educational Resources Information Center

Ellis, James D.; Kuerbis, Paul J.

1991-01-01

ENLIST Micros, a project designed to improve quality and quantity of microcomputer use in science teaching, is described. Rationale and procedures behind its development; description of the pilot test model; results of the initial field test and an implementation study; description of the revised ENLIST Micros curriculum; and recommendations for…

An examination of the usefulness of repeat testing practices in a large hospital clinical chemistry laboratory.

PubMed

Deetz, Carl O; Nolan, Debra K; Scott, Mitchell G

2012-01-01

A long-standing practice in clinical laboratories has been to automatically repeat laboratory tests when values trigger automated "repeat rules" in the laboratory information system such as a critical test result. We examined 25,553 repeated laboratory values for 30 common chemistry tests from December 1, 2010, to February 28, 2011, to determine whether this practice is necessary and whether it may be possible to reduce repeat testing to improve efficiency and turnaround time for reporting critical values. An "error" was defined to occur when the difference between the initial and verified values exceeded the College of American Pathologists/Clinical Laboratory Improvement Amendments allowable error limit. The initial values from 2.6% of all repeated tests (668) were errors. Of these 668 errors, only 102 occurred for values within the analytic measurement range. Median delays in reporting critical values owing to repeated testing ranged from 5 (blood gases) to 17 (glucose) minutes.

NASA GRC Technology Development Project for a Stirling Radioisotope Power System

NASA Technical Reports Server (NTRS)

Thieme, Lanny G.; Schreiber, Jeffrey G.

2000-01-01

NASA Glenn Research Center (GRC), the Department of Energy (DOE), and Stirling Technology Company (STC) are developing a Stirling convertor for an advanced radioisotope power system to provide spacecraft on-board electric power for NASA deep space missions. NASA GRC is conducting an in-house project to provide convertor, component, and materials testing and evaluation in support of the overall power system development. A first characterization of the DOE/STC 55-We Stirling Technology Demonstration Convertor (TDC) under the expected launch random vibration environment was recently completed in the NASA GRC Structural Dynamics Laboratory. Two TDCs also completed an initial electromagnetic interference (EMI) characterization at NASA GRC while being tested in a synchronized, opposed configuration. Materials testing is underway to support a life assessment of the heater head, and magnet characterization and aging tests have been initiated. Test facilities are now being established for an independent convertor performance verification and technology development. A preliminary Failure Mode Effect Analysis (FMEA), initial finite element analysis (FEA) for the linear alternator, ionizing radiation survivability assessment, and radiator parametric study have also been completed. This paper will discuss the status, plans, and results to date for these efforts.

Post-Test Inspection of Nasa's Evolutionary Xenon Thruster Long Duration Test Hardware: Ion Optics

NASA Technical Reports Server (NTRS)

Soulas, George C.; Shastry, Rohit

2016-01-01

A Long Duration Test (LDT) was initiated in June 2005 as a part of NASAs Evolutionary Xenon Thruster (NEXT) service life validation approach. Testing was voluntarily terminated in February 2014, with the thruster accumulating 51,184 hours of operation, processing 918 kg of xenon propellant, and delivering 35.5 MN-s of total impulse. This presentation will present the post-test inspection results to date for the thrusters ion optics.

BRIEF REPORT: The Role of Point of Care Testing for Patients with Acute Pharyngitis

PubMed Central

Atlas, Steven J; McDermott, Steven M; Mannone, Carol; Barry, Michael J

2005-01-01

Background There is no consensus favoring a particular strategy for evaluating patients with pharyngitis. Objective To compare a clinical decision aid and a rapid office-based point of care (POC) test with routine culture for group A β-hemolytic streptococcus (GAS). Design Prospective observational study. Participants Among 179 patients enrolled, 150 were eligible and 148 had POC testing and cultures initially performed. Measurements An encounter form included eligibility criteria, clinical information based upon the Centor rule, and treatment provided. Sensitivity and specificity of POC test compared to routine culture for GAS. Results Thirty-eight patients (25.7%) had a positive GAS culture. The POC test was 92.1% sensitive (95% confidence interval [CI] 80% to 98%) and 100% specific (95% CI 97% to 100%). Although the Centor rule did not adequately discriminate among symptomatic patients with or without GAS (receiver operating curve area 0.63), the 3 patients with a false-negative POC test had a Centor score of less than 2. Among patients with a negative POC test, 26% initially received antibiotics. Conclusions For patients with a Centor score of ≥2, a POC test was highly sensitive for GAS. Future studies should confirm these results and assess whether implementation of POC testing as part of a local practice guideline can decrease variability in testing and treatment. PMID:16050888

Deep flaws in weldments of aluminum and titanium

NASA Technical Reports Server (NTRS)

Masters, J. N.; Engstrom, W. L.; Bixler, W. D.

1974-01-01

Surface flawed specimens of 2219-T87 and 6Al-4V STA titanium weldments were tested to determine static failure modes, failure strength, and fatigue flaw growth characteristics. Thicknesses selected for this study were purposely set at values where, for most test conditions, abrupt instability of the flaw at fracture would not be expected. Static tests for the aluminum weldments were performed at room, LN2 and LH2 temperatures. Titanium static tests for tests were performed at room and LH2 temperatures. Results of the static tests were used to plot curves relating initial flaw size to leakage- or failure-stresses (i.e. "failure" locus curves). Cyclic tests, for both materials, were then performed at room temperature, using initial flaws only slightly below the previously established failure locus for typical proof stress levels. Cyclic testing was performed on pairs of specimens, one with and one without a simulated proof test cycle. Comparisons were made then to determine the value and effect of proof testing as affected by the various variables of proof and operating stress, flaw shape, material thickness, and alloy.

Testing for Turkeys Faith-Based Community HIV Testing Initiative: An Update.

PubMed

DeGrezia, Mary; Baker, Dorcas; McDowell, Ingrid

2018-06-04

Testing for Turkeys (TFT) HIV/hepatitis C virus (HCV) and sexually transmitted infection (STI) testing initiative is a joint effort between Older Women Embracing Life (OWEL), Inc., a nonprofit faith-based community HIV support and advocacy organization; the Johns Hopkins University Regional Partner MidAtlantic AIDS Education and Training Center (MAAETC); and the University of Maryland, Baltimore JACQUES Initiative (JI), and is now in its 11th year of providing HIV outreach, testing, and linkage to care. Since 2008, the annual TFT daylong community HIV testing and linkage to care initiative has been held 2 weeks before Thanksgiving at a faith-based center in Baltimore, Maryland, in a zip code where one in 26 adults and adolescents ages 13 years and older are living with HIV (Maryland Department of Health, Center for HIV Surveillance, Epidemiology, and Evaluation, 2017). TFT includes a health fair with vendors that supply an abundance of education information (handouts, videos, one-on-one counseling) and safer sex necessities, including male and female condoms, dental dams, and lube. Nutritious boxed lunches and beverages are provided to all attendees and volunteers. Everyone tested for HIV who stays to obtain their results is given a free frozen turkey as they exit. The Baltimore City Health Department is on hand with a confidential no-test list (persons in the state already known to have HIV) to diminish retesting of individuals previously diagnosed with HIV. However, linkage to care is available to everyone: newly diagnosed individuals and those previously diagnosed and currently out of care. Copyright © 2018 Association of Nurses in AIDS Care. Published by Elsevier Inc. All rights reserved.

Gap Test Calibrations and Their Scaling

NASA Astrophysics Data System (ADS)

Sandusky, Harold

2011-06-01

Common tests for measuring the threshold for shock initiation are the NOL large scale gap test (LSGT) with a 50.8-mm diameter donor/gap and the expanded large scale gap test (ELSGT) with a 95.3-mm diameter donor/gap. Despite the same specifications for the explosive donor and polymethyl methacrylate (PMMA) gap in both tests, calibration of shock pressure in the gap versus distance from the donor scales by a factor of 1.75, not the 1.875 difference in their sizes. Recently reported model calculations suggest that the scaling discrepancy results from the viscoelastic properties of PMMA in combination with different methods for obtaining shock pressure. This is supported by the consistent scaling of these donors when calibrated in water-filled aquariums. Calibrations with water gaps will be provided and compared with PMMA gaps. Scaling for other donor systems will also be provided. Shock initiation data with water gaps will be reviewed.

The development and initial validation of a sensitive bedside cognitive screening test.

PubMed

Faust, D; Fogel, B S

1989-01-01

Brief bedside cognitive examinations such as the Mini-Mental State Examination are designed to detect delirium and dementia but not more subtle or delineated cognitive deficits. Formal neuropsychological evaluation provides greater sensitivity and detects a wider range of cognitive deficits but is too lengthy for efficient use at the bedside or in epidemiological studies. The authors developed the High Sensitivity Cognitive Screen (HSCS), a 20-minute interview-based test, to identify patients who show disorder on formal neuropsychological evaluation. An initial study demonstrated satisfactory test-retest and interrater reliability. The HSCS was then administered to 60 psychiatric and neurological patients with suspected cognitive deficits but without gross impairment, who also completed formal neuropsychological testing. Results of both tests were independently classified as either normal, borderline, or abnormal. The HSCS correctly classified 93% of patients across the normal-abnormal dichotomy and showed promise for characterizing the extent and severity of cognitive dysfunction.

Serial testing for latent tuberculosis using QuantiFERON-TB Gold In-Tube: A Markov model.

PubMed

Moses, Mark W; Zwerling, Alice; Cattamanchi, Adithya; Denkinger, Claudia M; Banaei, Niaz; Kik, Sandra V; Metcalfe, John; Pai, Madhukar; Dowdy, David

2016-07-29

Healthcare workers (HCWs) in low-incidence settings are often serially tested for latent TB infection (LTBI) with the QuantiFERON-TB Gold In-Tube (QFT) assay, which exhibits frequent conversions and reversions. The clinical impact of such variability on serial testing remains unknown. We used a microsimulation Markov model that accounts for major sources of variability to project diagnostic outcomes in a simulated North American HCW cohort. Serial testing using a single QFT with the recommended conversion cutoff (IFN-g > 0.35 IU/mL) resulted in 24.6% (95% uncertainty range, UR: 23.8-25.5) of the entire population testing false-positive over ten years. Raising the cutoff to >1.0 IU/mL or confirming initial positive results with a (presumed independent) second test reduced this false-positive percentage to 2.3% (95%UR: 2.0-2.6%) or 4.1% (95%UR: 3.7-4.5%), but also reduced the proportion of true incident infections detected within the first year of infection from 76.5% (95%UR: 66.3-84.6%) to 54.8% (95%UR: 44.6-64.5%) or 61.5% (95%UR: 51.6-70.9%), respectively. Serial QFT testing of HCWs in North America may result in tremendous over-diagnosis and over-treatment of LTBI, with nearly thirty false-positives for every true infection diagnosed. Using higher cutoffs for conversion or confirmatory tests (for initial positives) can mitigate these effects, but will also diagnose fewer true infections.

An In-vitro Comparison of Force Loss of Orthodontic Non-Latex Elastics

PubMed Central

Alavi, Shiva; Tabatabaie, Atusa Rahnama; Hajizadeh, Fatemeh; Ardekani, Alireza Haerian

2014-01-01

Objective: The amount and consistency of the applied forces to the tooth are important factors in tooth movements; therefore, the aim of this study was to compare the initial force and the force loss of three brands of elastics in 24 hours. Materials and Methods: In this in-vitro study sixty non-latex elastics (3/16 medium) from three companies (Forestadent, Dentaurum and Ortho Technology) were randomly selected. Two static tests were performed, the first in a dry environment to evaluate the initial force and the other performed in a wet environment (artificial saliva) to evaluate the force loss in 24 hours. The Universal testing machine measured the forces after stretching the elastics to three times the lumen diameter. Data were analyzed by repeated measures ANOVA, One-way ANOVA, Tukey-HSD, Paired samples test, and one sample test. Results: The difference between the brands was significant (p=0.002). Force loss was observed in all samples; 4–7.5% force loss occurred after one hour and 19–38% force loss occurred after 24 hours. The average initial force of Forestadent and Ortho Technology was significantly higher than marketed forces (p<0.001), but the initial force of Dentaurum elastics was similar to the marketed force. Conclusion: The force loss over 24 hours time period was Forestadent>Dentaurum>Ortho-Technology. According to the initial force and force loss percentage it is suggested to replace the non-latex elastics several times a day. PMID:24910671

Lead paint removal with high-intensity light pulses.

PubMed

Grapperhaus, Michael J; Schaefer, Raymond B

2006-12-15

This paper presents the results of an initial investigation into using high-intensity incoherent light pulses to strip paint. Measurements of light pulse characteristics, the reflectivity of different paints and initial experiments on the threshold for paint removal, and paint removal are presented, along with an approximate model consistent with experimental results. Paint removal tests include lead paint, the reduction of lead levels to below levels required for lead abatement, as well as air and light emissions measurements that are within regulatory guidelines.

Cost-effectiveness of anatomical and functional test strategies for stable chest pain: public health perspective from a middle-income country.

PubMed

Bertoldi, Eduardo G; Stella, Steffen F; Rohde, Luis Eduardo P; Polanczyk, Carisi A

2017-05-04

The aim of this research is to evaluate the relative cost-effectiveness of functional and anatomical strategies for diagnosing stable coronary artery disease (CAD), using exercise (Ex)-ECG, stress echocardiogram (ECHO), single-photon emission CT (SPECT), coronary CT angiography (CTA) or stress cardiacmagnetic resonance (C-MRI). Decision-analytical model, comparing strategies of sequential tests for evaluating patients with possible stable angina in low, intermediate and high pretest probability of CAD, from the perspective of a developing nation's public healthcare system. Hypothetical cohort of patients with pretest probability of CAD between 20% and 70%. The primary outcome is cost per correct diagnosis of CAD. Proportion of false-positive or false-negative tests and number of unnecessary tests performed were also evaluated. Strategies using Ex-ECG as initial test were the least costly alternatives but generated more frequent false-positive initial tests and false-negative final diagnosis. Strategies based on CTA or ECHO as initial test were the most attractive and resulted in similar cost-effectiveness ratios (I$ 286 and I$ 305 per correct diagnosis, respectively). A strategy based on C-MRI was highly effective for diagnosing stable CAD, but its high cost resulted in unfavourable incremental cost-effectiveness (ICER) in moderate-risk and high-risk scenarios. Non-invasive strategies based on SPECT have been dominated. An anatomical diagnostic strategy based on CTA is a cost-effective option for CAD diagnosis. Functional strategies performed equally well when based on ECHO. C-MRI yielded acceptable ICER only at low pretest probability, and SPECT was not cost-effective in our analysis. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Zika Virus Testing Considerations: Lessons Learned from the First 80 Real-Time Reverse Transcription-PCR-Positive Cases Diagnosed in New York State.

PubMed

St George, Kirsten; Sohi, Inderbir S; Dufort, Elizabeth M; Dean, Amy B; White, Jennifer L; Limberger, Ronald; Sommer, Jamie N; Ostrowski, Stephanie; Wong, Susan J; Backenson, P Bryon; Kuhles, Daniel; Blog, Debra; Taylor, Jill; Hutton, Brad; Zucker, Howard A

2017-02-01

The performance and interpretation of laboratory tests for Zika virus (ZKV) continue to be evaluated. Serology is cross-reactive, laborious, and frequently difficult to interpret, and serum was initially solely recommended for molecular diagnosis. ZKV testing was initiated in January 2016 in New York State for symptomatic patients, pregnant women, their infants, and patients with Guillain-Barré syndrome who had traveled to areas with ZKV transmission. Subsequently, eligibility was expanded to pregnant women with sexual partners with similar travel histories. Serum and urine collected within 4 weeks of symptom onset or within 6 weeks of travel were tested with real-time reverse transcription-PCR (RT-PCR) assays targeting the ZKV envelope and NS2B genes. In this review of lessons learned from the first 80 positive cases in NYS, ZKV RNA was detected in urine only in 50 patients, in serum only in 19 patients, and in both samples concurrently in 11 patients, with average viral loads in urine a log higher than those in serum. Among 93 positive samples from the 80 patients, 41 were positive on both gene assays, 52 were positive on the envelope only, and none were positive on the NS2B only. Of the 80 infected patients, test results for 74 (93%) would have defined their infection status as not detected or equivocal if the requirement for positive results from two assay targets (two-target-positive requirement) in the initial federal guidance to public health laboratories was enforced, if urine was not tested, or if the extended eligibility time for molecular testing was not implemented. These changes facilitated more extensive molecular diagnosis of ZKV, reducing reliance on time-consuming and potentially inconclusive serology. Copyright © 2017 American Society for Microbiology.

Inhibition of chaotic escape from a potential well by incommensurate escape-suppressing excitations.

PubMed

Chacón, R; Martínez, J A

2002-03-01

Theoretical results are presented concerning the reduction of chaotic escape from a potential well by means of a harmonic parametric excitation that satisfies an ultrasubharmonic resonance condition with the escape-inducing excitation. The possibility of incommensurate escape-suppressing excitations is demonstrated by studying rational approximations to the irrational escape-suppressing frequency. The analytical predictions for the suitable amplitudes and initial phases of the escape-suppressing excitation are tested against numerical simulations based on a high-resolution grid of initial conditions. These numerical results indicate that the reduction of escape is reliably achieved for small amplitudes and at, and only at, the predicted initial phases. For the case of irrational escape-suppressing frequencies, the effective escape-reducing initial phases are found to lie close to the accumulation points of the set of suitable initial phases that are associated with the complete series of convergents up to the convergent giving the chosen rational approximation.

Electron cyclotron thruster new modeling results preparation for initial experiments

NASA Technical Reports Server (NTRS)

Hooper, E. Bickford

1993-01-01

The following topics are discussed: a whistler-based electron cyclotron resonance heating (ECRH) thruster; cross-field coupling in the helicon approximation; wave propagation; wave structure; plasma density; wave absorption; the electron distribution function; isothermal and adiabatic plasma flow; ECRH thruster modeling; a PIC code model; electron temperature; electron energy; and initial experimental tests. The discussion is presented in vugraph form.

College and Career Readiness Initiative: College Placement Testing Results for High School Students. Edition 2010-04

ERIC Educational Resources Information Center

Florida Department of Education, 2010

2010-01-01

The State of Florida launched the College and Career Readiness Initiative to improve student readiness for postsecondary education and promote success after high school graduation. During the 2008 legislative session, s. 1008.30 (3), F.S., (also known as Senate Bill (SB) "1908") was revised to provide an opportunity for postsecondary…

Pigeons exhibit higher accuracy for chosen memory tests than for forced memory tests in duration matching-to-sample.

PubMed

Adams, Allison; Santi, Angelo

2011-03-01

Following training to match 2- and 8-sec durations of feederlight to red and green comparisons with a 0-sec baseline delay, pigeons were allowed to choose to take a memory test or to escape the memory test. The effects of sample omission, increases in retention interval, and variation in trial spacing on selection of the escape option and accuracy were studied. During initial testing, escaping the test did not increase as the task became more difficult, and there was no difference in accuracy between chosen and forced memory tests. However, with extended training, accuracy for chosen tests was significantly greater than for forced tests. In addition, two pigeons exhibited higher accuracy on chosen tests than on forced tests at the short retention interval and greater escape rates at the long retention interval. These results have not been obtained in previous studies with pigeons when the choice to take the test or to escape the test is given before test stimuli are presented. It appears that task-specific methodological factors may determine whether a particular species will exhibit the two behavioral effects that were initially proposed as potentially indicative of metacognition.

Advanced Gas Turbine (AGT) powertrain system

NASA Technical Reports Server (NTRS)

Helms, H. E.; Kaufeld, J.; Kordes, R.

1981-01-01

A 74.5 kW(100 hp) advanced automotive gas turbine engine is described. A design iteration to improve the weight and production cost associated with the original concept is discussed. Major rig tests included 15 hours of compressor testing to 80% design speed and the results are presented. Approximately 150 hours of cold flow testing showed duct loss to be less than the design goal. Combustor test results are presented for initial checkout tests. Turbine design and rig fabrication is discussed. From a materials study of six methods to fabricate rotors, two have been selected for further effort. A discussion of all six methods is given.

DSS 13 frequency stability tests

NASA Technical Reports Server (NTRS)

Otoshi, T. Y.; Franco, M. M.

1987-01-01

In a previous article, the results of frequency stability tests at DSS 13 were presented in table form for tau = 1000 s for the test period May 1985 through March 1986. This article is a continuation of that initial report and presents specially selected Allan sigma (square root of variance) plots of each of the subsystem test previously reported. An additional result obtained from tests performed during July 1986 was included for completeness. The Allan sigma plots are useful in that frequency stability information is not only given for tau = 1000 s, but for tau values in the regions of 1, 100, 500, and 2000 s as well.

Overview of a stirling engine test project

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1980-01-01

Tests were conducted on three Stirling engines ranging in size from 1.33 to 53 horsepower (1 to 40 kW). The tests were directed toward developing alternative, backup component concepts to improve engine efficiency and performance or to reduce costs. Some of the activities included investigating attractive concepts and materials for cooler-regenerator units, installing a jet impingement device on a Stirling engine to determine its potential for improved engine performance, and presenting performance maps for initial characterization of Stirling engines. The experiment results of the tests are presented along with predictions of results of future tests to be conducted on the Stirling engines.

Federating Clinical Data from Six Pediatric Hospitals: Process and Initial Results for Microbiology from the PHIS+ Consortium

PubMed Central

Gouripeddi, Ramkiran; Warner, Phillip B.; Mo, Peter; Levin, James E.; Srivastava, Rajendu; Shah, Samir S.; de Regt, David; Kirkendall, Eric; Bickel, Jonathan; Korgenski, E. Kent; Precourt, Michelle; Stepanek, Richard L.; Mitchell, Joyce A.; Narus, Scott P.; Keren, Ron

2012-01-01

Microbiology study results are necessary for conducting many comparative effectiveness research studies. Unlike core laboratory test results, microbiology results have a complex structure. Federating and integrating microbiology data from six disparate electronic medical record systems is challenging and requires a team of varied skills. The PHIS+ consortium which is partnership between members of the Pediatric Research in Inpatient Settings (PRIS) network, the Children’s Hospital Association and the University of Utah, have used “FURTHeR’ for federating laboratory data. We present our process and initial results for federating microbiology data from six pediatric hospitals. PMID:23304298

The Montreal Cognitive Assessment as a preliminary assessment tool in general psychiatry: Validity of MoCA in psychiatric patients.

PubMed

Gierus, J; Mosiołek, A; Koweszko, T; Wnukiewicz, P; Kozyra, O; Szulc, A

2015-01-01

The aim of the presented research was to obtain the initial data regarding the validity of Montreal Cognitive Assessment (MoCA) in diagnosing cognitive impairment in psychiatrically hospitalized patients. The results in MoCA obtained from 221 patients were analyzed in terms of proportional participation of patients with particular diagnosis in three result ranges. In 67 patients, additional version of the scale was also used. Comparative analysis of average results in particular diagnostic groups (organically based disorders, disorders due to psychoactive substance use, psychotic disorders, neurotic disorders and personality disorders) was also carried out, as well as an analysis of the scale's accuracy as a diagnostic test in detecting organic disorders. The reliability of the test measured with between tests correlation coefficient rho=0.92 (P=.000). Significant differences between particular diagnoses groups were detected (J-T=13736; P=.000). The cutoff points of 23 turned out to have a satisfactory sensitivity and specificity (0.82 and 0.70, respectively) in diagnosing organically based disorders. The area below the receiver operating characteristic curve (AUC=0.854; P=.000) suggests that MoCA has a satisfactory value as a classifier. The initial data suggest MoCA's high value in prediction of future diagnosis of organically based disorders. The initial results obtained in particular group of diagnoses support construct validity of the method. Copyright © 2015 Elsevier Inc. All rights reserved.

RQL Sector Rig Testing of SiC/SiC Combustor Liners

NASA Technical Reports Server (NTRS)

Verrilli, Michael J.; Martin, Lisa C.; Brewer, David N.

2002-01-01

Combustor liners, manufactured from silicon carbide fiber-reinforced silicon carbide (SiC/SiC) were tested for 260 hr using a simulated gas turbine engine cycle. This report documents the results of the last 56 hr of testing. Damage occurred in one of the six different components that make up the combustor liner set, the rich zone liner. Cracks in the rich zone liner initiated at the leading edge due to stresses resulting from the component attachment configuration. Thin film thermocouples and fiber optic pyrometers were used to measure the rich zone liner's temperature and these results are reported.

29 CFR 1919.14 - Initial tests of cargo gear and tests after alterations, renewals or repairs.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 7 2013-07-01 2013-07-01 false Initial tests of cargo gear and tests after alterations, renewals or repairs. 1919.14 Section 1919.14 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) GEAR CERTIFICATION Certification of Vessels' Cargo Gear § 1919.14 Initial tests...

29 CFR 1919.14 - Initial tests of cargo gear and tests after alterations, renewals or repairs.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 7 2012-07-01 2012-07-01 false Initial tests of cargo gear and tests after alterations, renewals or repairs. 1919.14 Section 1919.14 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) GEAR CERTIFICATION Certification of Vessels' Cargo Gear § 1919.14 Initial tests...

29 CFR 1919.14 - Initial tests of cargo gear and tests after alterations, renewals or repairs.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 7 2014-07-01 2014-07-01 false Initial tests of cargo gear and tests after alterations, renewals or repairs. 1919.14 Section 1919.14 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) GEAR CERTIFICATION Certification of Vessels' Cargo Gear § 1919.14 Initial tests...

29 CFR 1919.14 - Initial tests of cargo gear and tests after alterations, renewals or repairs.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 7 2011-07-01 2011-07-01 false Initial tests of cargo gear and tests after alterations, renewals or repairs. 1919.14 Section 1919.14 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) GEAR CERTIFICATION Certification of Vessels' Cargo Gear § 1919.14 Initial tests...

Mesoscale Modeling, Forecasting and Remote Sensing Research.

DTIC Science & Technology

remote sensing , cyclonic scale diagnostic studies and mesoscale numerical modeling and forecasting are summarized. Mechanisms involved in the release of potential instability are discussed and simulated quantitatively, giving particular attention to the convective formulation. The basic mesoscale model is documented including the equations, boundary condition, finite differences and initialization through an idealized frontal zone. Results of tests including a three dimensional test with real data, tests of convective/mesoscale interaction and tests with a detailed

Interventions to improve or facilitate linkage to or retention in pre-ART (HIV) care and initiation of ART in low- and middle-income settings – a systematic review

PubMed Central

Govindasamy, Darshini; Meghij, Jamilah; Negussi, Eyerusalem Kebede; Baggaley, Rachel Clare; Ford, Nathan; Kranzer, Katharina

2014-01-01

Introduction Several approaches have been taken to reduce pre-antiretroviral therapy (ART) losses between HIV testing and ART initiation in low- and middle-income countries, but a systematic assessment of the evidence has not yet been undertaken. The aim of this systematic review is to assess the potential for interventions to improve or facilitate linkage to or retention in pre-ART care and initiation of ART in low- and middle-income settings. Methods An electronic search was conducted on Medline, Embase, Global Health, Web of Science and conference databases to identify studies describing interventions aimed at improving linkage to or retention in pre-ART care or initiation of ART. Additional searches were conducted to identify on-going trials on this topic, and experts in the field were contacted. An assessment of the risk of bias was conducted. Interventions were categorized according to key domains in the existing literature. Results A total of 11,129 potentially relevant citations were identified, of which 24 were eligible for inclusion, with the majority (n=21) from sub-Saharan Africa. In addition, 15 on-going trials were identified. The most common interventions described under key domains included: health system interventions (i.e. integration in the setting of antenatal care); patient convenience and accessibility (i.e. point-of-care CD4 count (POC) testing with immediate results, home-based ART initiation); behaviour interventions and peer support (i.e. improved communication, patient referral and education) and incentives (i.e. food support). Several interventions showed favourable outcomes: integration of care and peer supporters increased enrolment into HIV care, medical incentives increased pre-ART retention, POC CD4 testing and food incentives increased completion of ART eligibility screening and ART initiation. Most studies focused on the general adult patient population or pregnant women. The majority of published studies were observational cohort studies, subject to an unclear risk of bias. Conclusions Findings suggest that streamlining services to minimize patient visits, providing adequate medical and peer support, and providing incentives may decrease attrition, but the quality of the current evidence base is low. Few studies have investigated combined interventions, or assessed the impact of interventions across the HIV cascade. Results from on-going trials investigating POC CD4 count testing, patient navigation, rapid ART initiation and mobile phone technology may fill the quality of evidence gap. Further high-quality studies on key population groups are required, with interventions informed by previously reported barriers to care. PMID:25095831

Which routine test for kidney function?

PubMed Central

Parkin, A; Smith, H C; Brocklebank, J T

1989-01-01

Eighty measurements of plasma creatinine concentration, height:creatinine ratio, and plasma beta 2 microglobulin concentration were made on 72 children (age 4 months-18.5 years) with known renal disease. Results were compared with simultaneous measurements of glomerular filtration rate using plasma clearance of 51Cr edetic acid to assess the performance of each test as an initial screening procedure of renal insufficiency. Height:creatinine index less than 2.1 was found to have a higher sensitivity and predictive value of a normal result than the other tests and is therefore the preferred test for a screening procedure. PMID:2510609

Pretest and posttest calculations of Semiscale Test S-07-10D with the TRAC computer program. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duerre, K.H.; Cort, G.E.; Knight, T.D.

The Transient Reactor Analysis Code (TRAC) developed at the Los Alamos National Laboratory was used to predict the behavior of the small-break experiment designated Semiscale S-07-10D. This test simulates a 10 per cent communicative cold-leg break with delayed Emergency Core Coolant injection and blowdown of the broken-loop steam generator secondary. Both pretest calculations that incorporated measured initial conditions and posttest calculations that incorporated measured initial conditions and measured transient boundary conditions were completed. The posttest calculated parameters were generally between those obtained from pretest calculations and those from the test data. The results are strongly dependent on depressurization rate and,more » hence, on break flow.« less

[Objective evaluation of arterial intermittent claudication by the walking tolerance test. Comparative study of physiological walking and walking on a conveyor belt (author's transl)].

PubMed

Bouchet, J Y; Franco, A; Morzol, B; Beani, J C

1980-01-01

Two methods are used to evaluate the walking distance: physiological walking along a standard path (0% - 6 mk/h) and walking on a tread mill (10% - 3 km/h). In both tests, four data are checked: -- initial trouble distance, -- cramp or walking-distance, -- localisation of pain, -- recovery time. These tests are dependable for the diagnosis of arterial claudication, reproducible and well tolerated. Their results have been compared: there is no correlation between the initial trouble distance and the cramp distance. However there is a correlation between the cramp distance by physiological walking and on treadmill. Recovery time, if long, is a criteria of gravity. Interests of both methods are discussed.

Peridynamic Applications for Orthotropic Materials

DTIC Science & Technology

2012-09-26

test and a vibration excitation of a laminated beam. An SEN (single edge notch) test of a 0° laminated plate was simulated by peridynamics and the...computational results matched very well with published experimental results. Fracture initiation and crack path of laminated plates with different fiber...Dwivedi [1] modeled the propagation of single-edge notch (SEN) in 0° laminated plate using cohesizve zone method. Xu [2] and Hu [3] proposed a two

Free-piston Stirling component test power converter

NASA Technical Reports Server (NTRS)

Dochat, George; Dhar, Manmohan

1991-01-01

The National Aeronautics and Space Administration (NASA) has been evaluating free-piston Stirling power converters (FPSPCs) for use on a wide variety of space missions. They provide high reliability, long life, and efficient operation and can be coupled with all potential heat sources, various heat input and heat rejection systems, and various power management and distribution systems. FPSPCs can compete favorably with alternative power conversion systems over a range of hundreds of watts to megawatts. Mechanical Technology Incorporated (MTI) is developing FPSPC technology under contract to NASA Lewis Research Center and will demonstrate this technology in two full-scale power converters operating at space temperature conditions. The testing of the first of these, the component test power converter (CTPC), was initiated in Spring 1991 to evaluate mechanical operation at space operating temperatures. The CTPC design, hardware fabrication, and initial test results are reviewed.

The case against one-shot testing for initial dental licensure.

PubMed

Chambers, David W; Dugoni, Arthur A; Paisley, Ian

2004-03-01

High-stakes testing are expected to meet standards for cost-effectiveness, fairness, transparency, high reliability, and high validity. It is questionable whether initial licensure examinations in dentistry meet such standards. Decades of piecemeal adjustments in the system have resulted in limited improvement. The essential flaw in the system is reliance on a one-shot sample of a small segment of the skills, understanding, and supporting values needed for today's professional practice of dentistry. The "snapshot" approach to testing produces inherently substandard levels of reliability and validity. A three-step alternative is proposed: boards should (1) define the competencies required of beginning practitioners, (2) establish the psychometric standards needed to make defensible judgments about candidates, and (3) base licensure decisions only on portfolios of evidence that test for defined competencies at established levels of quality.

The Role of Hemoglobin Laboratory Test Results for the Detection of Upper Gastrointestinal Bleeding Outcomes Resulting from the Use of Medications in Observational Studies.

PubMed

Patorno, Elisabetta; Gagne, Joshua J; Lu, Christine Y; Haynes, Kevin; Sterrett, Andrew T; Roy, Jason; Wang, Xingmei; Raebel, Marsha A

2017-01-01

The identification of upper gastrointestinal (UGI) bleeding and perforated ulcers in claims data typically relies on inpatient diagnoses. The use of hemoglobin laboratory results might increase the detection of UGI events that do not lead to hospitalization. Our objective was to evaluate whether hemoglobin results increase UGI outcome identification in electronic databases, using non-steroidal anti-inflammatory drugs (NSAIDs) as a test case. From three data partner sites within the Mini-Sentinel Distributed Database, we identified NSAID initiators aged ≥18 years between 2008 and 2013. Numbers of events and risks within 30 days after NSAID initiation were calculated for four mutually exclusive outcomes: (1) inpatient UGI diagnosis of bleeding or gastric ulcer (standard claims-based definition without laboratory results); (2) non-inpatient UGI diagnosis AND ≥3 g/dl hemoglobin decrease; (3) ≥3 g/dl hemoglobin decrease without UGI diagnosis in any clinical setting; (4) non-inpatient UGI diagnosis, without ≥3 g/dl hemoglobin decrease. We identified 2,289,772 NSAID initiators across three sites. Overall, 45.3% had one or more hemoglobin result available within 365 days before or 30 days after NSAID initiation; only 6.8% had results before and after. Of 7637 potential outcomes identified, outcome 1 accounted for 21.7%, outcome 2 for 0.8%, outcome 3 for 34.3%, and outcome 4 for 43.3%. Potential cases identified by outcome 3 were largely not suggestive of UGI events. Outcomes 1, 2, and 4 had similar distributions of specific UGI diagnoses. Using available hemoglobin result values combined with non-inpatient UGI diagnoses identified few additional UGI cases. Non-inpatient UGI diagnostic codes may increase outcome detection but would require validation.

Starter/generator testing

NASA Astrophysics Data System (ADS)

Anon

1994-10-01

Sundstrand Aerospace and GE Aircraft Engines have studied the switched reluctance machine for use as an integral starter/generator for future aircraft engines. They have conducted an initial, low-power testing of the starter/generator, which is based on power inverters using IGBT-technology semiconductors, to verify its feasibility in the externally mounted version of the integral starter/generator. This preliminary testing of the 250-kW starter/generator reveals favorable results.

Evaluation program for secondary spacecraft cells: Initial evaluation tests of General Electric Company 6.0 ampere-hour nickel-cadmium spacecraft cells for the Improved Tiros Operational Satellite (ITOS)

NASA Technical Reports Server (NTRS)

Harkness, J. D.

1975-01-01

Quality control measures for Ni-Cd spacecraft cells were analyzed. Cells were examined for electrolyte leakage, internal shorts, low capacity, or inability of any cell to recover its open circuit voltage above 1.50 volts during the internal short test. Test results are given in tabular form.

IMP-I spacecraft final magnetic tests

NASA Technical Reports Server (NTRS)

Harris, C. A.

1972-01-01

The increased IMP-I spacecraft spin axis moment resulting from excessive field exposures during environmental testing substantiated the need for a final pre-launch magnetic deperm and measurement. By performing a dc rotation deperm it was possible to reduce this moment below the previous initial test post deperm magnitude. In addition, the magnetic field disturbance at the flight magnetometer diminished to below 0.1 nanotesla (gamma) in all directions.

Unique Challenges to Preventing Perinatal HIV Transmission among Hispanic Women in California: Results of a Needs Assessment

ERIC Educational Resources Information Center

Kropp, Rhonda Y.; Montgomery, Elizabeth T.; Hill, David W.; Ruiz, Juan D.; Maldonado, Yvonne A.

2005-01-01

To identify rates and factors associated with timely prenatal care (PNC) initiation, HIV test counseling, test offering, and test offer acceptance, we conducted a semistructured survey of a convenience sample of pregnant/recently delivered Hispanic women (n = 453, 418 with analyzable data) in four California counties in 2000. Only 68.4% and 43.5%…

A shift from significance test to hypothesis test through power analysis in medical research.

PubMed

Singh, G

2006-01-01

Medical research literature until recently, exhibited substantial dominance of the Fisher's significance test approach of statistical inference concentrating more on probability of type I error over Neyman-Pearson's hypothesis test considering both probability of type I and II error. Fisher's approach dichotomises results into significant or not significant results with a P value. The Neyman-Pearson's approach talks of acceptance or rejection of null hypothesis. Based on the same theory these two approaches deal with same objective and conclude in their own way. The advancement in computing techniques and availability of statistical software have resulted in increasing application of power calculations in medical research and thereby reporting the result of significance tests in the light of power of the test also. Significance test approach, when it incorporates power analysis contains the essence of hypothesis test approach. It may be safely argued that rising application of power analysis in medical research may have initiated a shift from Fisher's significance test to Neyman-Pearson's hypothesis test procedure.

10 CFR 26.131 - Cutoff levels for validity screening and initial validity tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Cutoff levels for validity screening and initial validity tests. 26.131 Section 26.131 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Licensee Testing Facilities § 26.131 Cutoff levels for validity screening and initial validity tests. (a) Each...

10 CFR 26.131 - Cutoff levels for validity screening and initial validity tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Cutoff levels for validity screening and initial validity tests. 26.131 Section 26.131 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Licensee Testing Facilities § 26.131 Cutoff levels for validity screening and initial validity tests. (a) Each...

Opioid tolerance and urine drug testing among initiates of extended-release or long-acting opioids in Food and Drug Administration's Sentinel System.

PubMed

Larochelle, Marc R; Cocoros, Noelle M; Popovic, Jennifer; Dee, Elizabeth C; Kornegay, Cynthia; Ju, Jing; Racoosin, Judith A

A risk evaluation and mitigation strategy for extended-release and long-acting (ER/LA) opioid analgesics was approved by the Food and Drug Administration in 2012. Our objective was to assess frequency of opioid tolerance and urine drug testing for individuals initiating ER/LA opioid analgesics. Retrospective cohort study. Sentinel, a distributed database with electronic healthcare data on >190 million predominantly commercially insured members. Members under age 65 initiating ER/LA opioid analgesics between January 2009 and December 2013. We examined the proportion of opioid-tolerant-only ER/LA opioid analgesic initiates meeting tolerance criteria: receipt of ≥30 mg oxycodone equivalents per day in 7 days prior to the first opioid-tolerant-only dispensing. We separately examined the proportion of new users of extended-release oxycodone (ERO) and other ER/LA opioid analgesics with a claim for a urine drug test in the 30 days prior to, and separately for the 183 days after, dispensing. We identified 79,824 ERO, 7,343 extended-release hydromorphone, and 91,778 transdermal fentanyl opi-oid-tolerant-only episodes. Tolerance criteria were met in 64 percent of ERO, 64 percent of extended-release hydromorphone and 40 percent of transdermal fentanyl episodes. We identified 210,581 incident ERO and 311,660 other ER/LA opioid analgesic episodes. Use of urine drug testing for ERO compared with other ER/LA opioid analgesics was: 4 percent vs 14 percent respectively in the 30 days prior to initiation and 9 percent vs 23 percent respectively in the 183 days following initiation. These results suggest potential areas for improving appropriate ER/LA opioid analgesic prescribing practices.

Sulfonylurea Treatment Before Genetic Testing in Neonatal Diabetes: Pros and Cons

PubMed Central

Carmody, David; Bell, Charles D.; Hwang, Jessica L.; Dickens, Jazzmyne T.; Sima, Daniela I.; Felipe, Dania L.; Zimmer, Carrie A.; Davis, Ajuah O.; Kotlyarevska, Kateryna; Naylor, Rochelle N.; Philipson, Louis H.

2014-01-01

Context: Diabetes in neonates nearly always has a monogenic etiology. Earlier sulfonylurea therapy can improve glycemic control and potential neurodevelopmental outcomes in children with KCNJ11 or ABCC8 mutations, the most common gene causes. Objective: Assess the risks and benefits of initiating sulfonylurea therapy before genetic testing results become available. Design, Setting, and Patients: Observational retrospective study of subjects with neonatal diabetes within the University of Chicago Monogenic Diabetes Registry. Main Outcome Measures: Response to sulfonylurea (determined by whether insulin could be discontinued) and treatment side effects in those treated empirically. Results: A total of 154 subjects were diagnosed with diabetes before 6 months of age. A genetic diagnosis had been determined in 118 (77%), with 73 (47%) having a mutation in KCNJ11 or ABCC8. The median time from clinical diagnosis to genetic diagnosis was 10.4 weeks (range, 1.6 to 58.2 wk). In nine probands, an empiric sulfonylurea trial was initiated within 28 days of diabetes diagnosis. A genetic cause was subsequently found in eight cases, and insulin was discontinued within 14 days of sulfonylurea initiation in all of these cases. Conclusions: Sulfonylurea therapy appears to be safe and often successful in neonatal diabetes patients before genetic testing results are available; however, larger numbers of cases must be studied. Given the potential beneficial effect on neurodevelopmental outcome, glycemic control, and the current barriers to expeditious acquisition of genetic testing, an empiric inpatient trial of sulfonylurea can be considered. However, obtaining a genetic diagnosis remains imperative to inform long-term management and prognosis. PMID:25238204

Particle size and surface area effects on the thin-pulse shock initiation of Diaminoazoxyfurazan (DAAF)

NASA Astrophysics Data System (ADS)

Burritt, Rosemary; Francois, Elizabeth; Windler, Gary; Chavez, David

2017-06-01

Diaminoazoxyfurazan (DAAF) has many of the safety characteristics of an insensitive high explosive (IHE): it is extremely insensitive to impact and friction and is comparable to triaminotrinitrobezene (TATB) in this way. Conversely, it demonstrates many performance characteristics of a Conventional High Explosive (CHE). DAAF has a small failure diameter of about 1.25 mm and can be sensitive to shock under the right conditions. Large particle sized DAAF will not initiate in a typical exploding foil initiator (EFI) configuration but smaller particle sizes will. Large particle sized DAAF, of 40 μm, was crash precipitated and ball milled into six distinct samples and pressed into pellets with a density of 1.60 g/cc (91% TMD). To investigate the effect of particle size and surface area on the direct initiation on DAAF multiple threshold tests were preformed on each sample of DAAF in different EFI configurations, which varied in flyer thickness and/or bridge size. Comparative tests were performed examining threshold voltage and correlated to Photon Doppler Velocimetry (PDV) results. The samples with larger particle sizes and surface area required more energy to initiate while the smaller particle sizes required less energy and could be initiated with smaller diameter flyers.

Experimental Investigation of Shock Initiation in Mixtures of Manganese and Sulfur

NASA Astrophysics Data System (ADS)

Jette, Francois-Xavier; Goroshin, Sam; Higgins, Andrew

2009-06-01

Equimolar mixtures of manganese powder and sulfur at different initial densities were tested in two different types of steel recovery capsules in order to study the shock initiation phenomenon in SHS mixtures. This mixture composition was selected due to the large exothermic heat release of the manganese-sulfur reaction (214 kJ/mol), which causes the reaction to be self-sustaining once initiated. Two different sizes of Mn particles were used for these experiments, 1-5 μm and -325 mesh (44μm or less). The test samples were placed in planar recovery ampoules and a strong shock was delivered via the detonation of a charge of amine-sensitized nitromethane. Various shock strengths were achieved by placing different thicknesses of PMMA attenuator discs between the explosive charge and the ampoule. The results confirmed that shock-induced reactions can be produced in highly non-porous mixtures. It was also found that shock interactions with the side walls of the recovery capsule can play a significant role in the initiation, and that mixtures containing the larger Mn particles were very difficult to initiate in the absence of shock interactions with the capsule walls.

Mechanical characteristics and comparisons of cerclage wires: introduction of the double-wrap and loop/twist tying methods.

PubMed

Roe, S C

1997-01-01

Evaluate the mechanical properties of twist, loop, double loop, double-wrap and loop/twist cerclage. The initial tension generated by 18 cerclage of each type was determined using a materials testing machine after tying around a testing jig. Six wires from each type were distracted and the initial stiffness and yield load were determined. Yield behavior was further investigated in six wires of each type by determining the load required to reduce cerclage tension below 30 Newton (N) following and incremental (50 N) stepwise load and unload regimen. The amount of collapse of the simulated bone fragments that resulted in the reduction of initial tension to 30 N was measured for the final six wires of each group. Data were analyzed by analysis of variance and a multiple comparison test. Twist type cerclage generated less tension than loop-type cerclage. The yield load of these two types was similar. Double-loop and double-wrap cerclage generated superior tension and resisted a greater load before loosening. Loop/twist cerclage had an intermediate initial tension but had the greatest resistance to loading. In the collapse test, the greater the initial tension, the more collapse could occur before the wire was loose. For all types of cerclage wire fixation, a reduction of diameter of the testing jig of more than 1% caused loosening. Double-loop and double-wrap cerclage provide greater compression of fragments and resist loads associated with weight-bearing better than the twist and loop methods. Loop/twist cerclage may have advantages because of their superior resistance to loading. All cerclage will loosen if fracture fragments collapse.

Prediction of fracture initiation in square cup drawing of DP980 using an anisotropic ductile fracture criterion

NASA Astrophysics Data System (ADS)

Park, N.; Huh, H.; Yoon, J. W.

2017-09-01

This paper deals with the prediction of fracture initiation in square cup drawing of DP980 steel sheet with the thickness of 1.2 mm. In an attempt to consider the influence of material anisotropy on the fracture initiation, an uncoupled anisotropic ductile fracture criterion is developed based on the Lou—Huh ductile fracture criterion. Tensile tests are carried out at different loading directions of 0°, 45°, and 90° to the rolling direction of the sheet using various specimen geometries including pure shear, dog-bone, and flat grooved specimens so as to calibrate the parameters of the proposed fracture criterion. Equivalent plastic strain distribution on the specimen surface is computed using Digital Image Correlation (DIC) method until surface crack initiates. The proposed fracture criterion is implemented into the commercial finite element code ABAQUS/Explicit by developing the Vectorized User-defined MATerial (VUMAT) subroutine which features the non-associated flow rule. Simulation results of the square cup drawing test clearly show that the proposed fracture criterion is capable of predicting the fracture initiation with sufficient accuracy considering the material anisotropy.

A kinematic analysis of the rapid step test in balance-impaired and unimpaired older women.

PubMed

Schulz, Brian W; Ashton-Miller, James A; Alexander, Neil B

2007-04-01

Little is known about the kinematic and kinetic determinants that might explain age and balance-impairment alterations in the results of volitional stepping performance tests. Maximal unipedal stance time (UST) was used to distinguish "balance-impaired" old (BI, UST<10s, N=15, mean age=76 years) from unimpaired old (O, UST>30s, N=12, mean age=71 years) before they and healthy young females (Y, UST>30s, N=13, mean age=23 years) performed the rapid step test (RST). The RST evaluates the time required to take volitional front, side, and back steps of at least 80% maximum step length in response to verbal commands. Kinematic and kinetic data were recorded during the RST. The results indicate that the initiation phase of the step was the major source of age- and balance impairment-related delays. The delays in BI were primarily caused by increased postural adjustments prior to step initiation, as measured by center-of-pressure (COP) path length (p<0.003). The Step landing phase showed similar, but non-significant, temporal trends. Step length and peak center-of-mass (COM) deceleration during the Step-Out landing decreased in O by 18% (p=0.0002) and 24% (p=0.001), respectively, and a further 12% (p=0.04) and 18% (p=0.08) in BI. We conclude that the delay in BI step initiation was due to the increase in their postural adjustments prior to step initiation.

Modeling learning and memory using verbal learning tests: results from ACTIVE.

PubMed

Gross, Alden L; Rebok, George W; Brandt, Jason; Tommet, Doug; Marsiske, Michael; Jones, Richard N

2013-03-01

To investigate the influence of memory training on initial recall and learning. The Advanced Cognitive Training for Independent and Vital Elderly study of community-dwelling adults older than age 65 (n = 1,401). We decomposed trial-level recall in the Auditory Verbal Learning Test (AVLT) and Hopkins Verbal Learning Test (HVLT) into initial recall and learning across trials using latent growth models. Trial-level increases in words recalled in the AVLT and HVLT at each follow-up visit followed an approximately logarithmic shape. Over the 5-year study period, memory training was associated with slower decline in Trial 1 AVLT recall (Cohen's d = 0.35, p = .03) and steep pre- and posttraining acceleration in learning (d = 1.56, p < .001). Findings were replicated using the HVLT (decline in initial recall, d = 0.60, p = .01; pre- and posttraining acceleration in learning, d = 3.10, p < .001). Because of the immediate training boost, the memory-trained group had a higher level of recall than the control group through the end of the 5-year study period despite faster decline in learning. This study contributes to the understanding of the mechanisms by which training benefits memory and expands current knowledge by reporting long-term changes in initial recall and learning, as measured from growth models and by characterization of the impact of memory training on these components. Results reveal that memory training delays the worsening of memory span and boosts learning.

Rocketdyne LOX bearing tester program

NASA Technical Reports Server (NTRS)

Keba, J. E.; Beatty, R. F.

1988-01-01

The cause, or causes, for the Space Shuttle Main Engine ball wear were unknown, however, several mechanisms were suspected. Two testers were designed and built for operation in liquid oxygen to empirically gain insight into the problems and iterate solutions in a timely and cost efficient manner independent of engine testing. Schedules and test plans were developed that defined a test matrix consisting of parametric variations of loading, cooling or vapor margin, cage lubrication, material, and geometry studies. Initial test results indicated that the low pressure pump thrust bearing surface distress is a function of high axial load. Initial high pressure turbopump bearing tests produced the wear phenomenon observed in the turbopump and identified an inadequate vapor margin problem and a coolant flowrate sensitivity issue. These tests provided calibration data of analytical model predictions to give high confidence in the positive impact of future turbopump design modification for flight. Various modifications will be evaluated in these testers, since similar turbopump conditions can be produced and the benefit of the modification will be quantified in measured wear life comparisons.

Hybrid TE panel test results

NASA Technical Reports Server (NTRS)

Bifano, W. J.

1972-01-01

Test results are presented for a nine couple (3 x 3 array) thermoelectric panel of hybrid thermocouples. In the hybrid couple, a hollow cylinder of p-type Si-Ge is used to encapsulate a segmented PbTe/Si-Ge n-leg. The hybrid couple is predicted to offer a 10- to 15-percent improvement in performance relative to all Si-Ge couples. The efficiency, output power, and internal resistance of the panel as well as the resistances of the individual hybrid couples are presented as a function of test time covering a period of more than 2600 hours. Initial test results indicated hybrid couple performance consistent with design predictions. Extraneous resistance ranged from 20 to 25% of the hybrid couple thermoelectric resistance.

Dot Projection Photogrammetric Technique for Shape Measurements of Aerospace Test Articles

NASA Technical Reports Server (NTRS)

Jones, Thomas W.; Pappa, Richard S.

2002-01-01

Results from initial laboratory investigations with the dot projection photogrammetric technique are presented for three wind-tunnel test articles with a range of surface scattering and reflection properties. These test articles are a semispan model and a micro air vehicle with a latex wing that are both diffusely reflecting, and a highly polished specularly reflecting model used for high Reynolds number testing. Results using both white light and laser illumination are presented. Some of the advantages and limitations of the dot projection technique are discussed. Although a desirable final outcome of this research effort is the characterization of dynamic behavior, only static laboratory results are presented in this preliminary effort.

Developing an ANSI standard for image quality tools for the testing of active millimeter wave imaging systems

NASA Astrophysics Data System (ADS)

Barber, Jeffrey; Greca, Joseph; Yam, Kevin; Weatherall, James C.; Smith, Peter R.; Smith, Barry T.

2017-05-01

In 2016, the millimeter wave (MMW) imaging community initiated the formation of a standard for millimeter wave image quality metrics. This new standard, American National Standards Institute (ANSI) N42.59, will apply to active MMW systems for security screening of humans. The Electromagnetic Signatures of Explosives Laboratory at the Transportation Security Laboratory is supporting the ANSI standards process via the creation of initial prototypes for round-robin testing with MMW imaging system manufacturers and experts. Results obtained for these prototypes will be used to inform the community and lead to consensus objective standards amongst stakeholders. Images collected with laboratory systems are presented along with results of preliminary image analysis. Future directions for object design, data collection and image processing are discussed.

Adjustable typography: an approach to enhancing low vision text accessibility.

PubMed

Arditi, Aries

2004-04-15

Millions of people have low vision, a disability condition caused by uncorrectable or partially correctable disorders of the eye. The primary goal of low vision rehabilitation is increasing access to printed material. This paper describes how adjustable typography, a computer graphic approach to enhancing text accessibility, can play a role in this process, by allowing visually-impaired users to customize fonts to maximize legibility according to their own visual needs. Prototype software and initial testing of the concept is described. The results show that visually-impaired users tend to produce a variety of very distinct fonts, and that the adjustment process results in greatly enhanced legibility. But this initial testing has not yet demonstrated increases in legibility over and above the legibility of highly legible standard fonts such as Times New Roman.

Cascade heterogeneous face sketch-photo synthesis via dual-scale Markov Network

NASA Astrophysics Data System (ADS)

Yao, Saisai; Chen, Zhenxue; Jia, Yunyi; Liu, Chengyun

2018-03-01

Heterogeneous face sketch-photo synthesis is an important and challenging task in computer vision, which has widely applied in law enforcement and digital entertainment. According to the different synthesis results based on different scales, this paper proposes a cascade sketch-photo synthesis method via dual-scale Markov Network. Firstly, Markov Network with larger scale is used to synthesise the initial sketches and the local vertical and horizontal neighbour search (LVHNS) method is used to search for the neighbour patches of test patches in training set. Then, the initial sketches and test photos are jointly entered into smaller scale Markov Network. Finally, the fine sketches are obtained after cascade synthesis process. Extensive experimental results on various databases demonstrate the superiority of the proposed method compared with several state-of-the-art methods.

The shortened food expectations--Long-term care questionnaire: Assessing nursing home residents' satisfaction with food and food service.

PubMed

Crogan, Neva L; Evans, Bronwynne C

2006-11-01

Lack of nursing home resident satisfaction with meals often results in reduced food intake, leading to poor nutritional status, weight loss, functional decline, and depression. The purpose of this article is to describe the development and initial testing of the 28-item revised Food Expectations-Long-Term Care (FoodEx-LTC) questionnaire with a convenience sample of nursing home residents (N = 61). Because of possible respondent burden, the original 44-item, five-domain FoodEx-LTC was revised, resulting in the deletion of 16 redundant items and those with inter-item correlations less than .25. Coefficient alpha scores ranged from .65 to .82, and test-retest correlations ranged from .79 to .88, dependent on domain. This revised instrument has good initial validity and reliability, resulting in a shorter instrument that accurately assesses nursing home resident satisfaction with food and food service.

An initial investigation into methods of computing transonic aerodynamic sensitivity coefficients

NASA Technical Reports Server (NTRS)

Carlson, Leland A.

1991-01-01

Continuing studies associated with the development of the quasi-analytical (QA) sensitivity method for three dimensional transonic flow about wings are presented. Furthermore, initial results using the quasi-analytical approach were obtained and compared to those computed using the finite difference (FD) approach. The basic goals achieved were: (1) carrying out various debugging operations pertaining to the quasi-analytical method; (2) addition of section design variables to the sensitivity equation in the form of multiple right hand sides; (3) reconfiguring the analysis/sensitivity package in order to facilitate the execution of analysis/FD/QA test cases; and (4) enhancing the display of output data to allow careful examination of the results and to permit various comparisons of sensitivity derivatives obtained using the FC/QA methods to be conducted easily and quickly. In addition to discussing the above goals, the results of executing subcritical and supercritical test cases are presented.

Heavy-section steel irradiation program. Progress report, April 1996--September 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corwin, W.R.

1997-09-01

The Heavy-Section Steel Irradiation Program was established to quantitatively assess the effects of neutron irradiation on the material behavior of typical reactor pressure vessel (RPV) steels. During this period, fracture mechanics testing of specimens of the irradiated low upper shelf (LUS) weld were completed and analyses performed. Heat treatment of five RPV plate materials was initiated to examine phosphorus segregation effects on the fracture toughness of the heat affected zone of welds. Initial results show that all five materials exhibited very large prior austenite grain sizes as a consequence of the initial heat treatment. Irradiated and annealed specimens of LUSmore » weld material were tested and analyzed. Four sets of Charpy V-notch (CVN) specimens were aged at various temperatures and tested to examine the reason for overrecovery of upper shelf energy that has been observed. Molecular dynamics cascade simulations were extended to 40 keV and have provided information representative of most of the fast neutron spectrum. Investigations of the correlation between microstructural changes and hardness changes in irradiated model alloys was also completed. Preliminary planning for test specimen machining for the Japan Power Development Reactor was completed. A database of Charpy impact and fracture toughness data for RPV materials that have been tested in the unirradiated and irradiated conditions is being assembled and analyzed. Weld metal appears to have similar CVN and fracture toughness transition temperature shifts, whereas the fracture toughness shifts are greater than CVN shifts for base metals. Draft subcontractor reports on precracked cylindrical tensile specimens were completed, reviewed, and are being revised. Testing on precracked CVN specimens, both quasi-static and dynamic, was evaluated. Additionally, testing of compact specimens was initiated as an experimental comparison of constraint limitations. 16 figs., 2 tabs.« less

40 CFR 60.2870 - What are the recordkeeping and reporting requirements for air curtain incinerators?

Code of Federal Regulations, 2011 CFR

2011-07-01

... SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration... records of results of all initial and annual opacity tests onsite in either paper copy or electronic... annual opacity test reports as electronic or paper copy on or before the applicable submittal date and...

40 CFR 60.2870 - What are the recordkeeping and reporting requirements for air curtain incinerators?

Code of Federal Regulations, 2010 CFR

2010-07-01

... SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration... records of results of all initial and annual opacity tests onsite in either paper copy or electronic... annual opacity test reports as electronic or paper copy on or before the applicable submittal date and...

40 CFR 63.11456 - What are the notification requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... § 63.9(b)(2), if you start up your affected source before December 26, 2007, you must submit an Initial..., including the performance test results, before the close of business on the 60th day following the... performance test, before the close of business on the compliance date specified in § 63.11450. ...

40 CFR 75.63 - Initial certification or recertification application.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirement of § 75.59(e), for DAHS (missing data and formula) verifications, no hardcopy submittal is... test data and results to the Administrator. (B) To the applicable EPA Regional Office and the... part) tests or any CEMS data analysis used to derive a fuel-and-unit-specific default NOX emission rate...

Integrated Thermal Modules for Cooling Silicon and Silicon Carbide Power Modules

DTIC Science & Technology

2007-06-11

analyses, bench tests, and motor tests comprise the program. The ITMs, in place of standard heatsinks, use a highly conductive pyrolytic graphite to...passively cool power modules. Initial results show that even simple ITMs can lower chip temperatures by 20 deg. C and 10 deg. C with engine oil and

Improvement of a Harvester Based, Multispectral, Seed Cotton Fiber Quality Sensor

USDA-ARS?s Scientific Manuscript database

A multispectral sensor for in-situ seed cotton fiber quality measurement was developed and tested at Texas A&M University. Results of initial testing of the sensor using machine harvested seed cotton have shown promise. Improvements have been made to the system and the measurement method to meet t...

Pilot model expansion tunnel test flow properties obtained from velocity, pressure, and probe measurements

NASA Technical Reports Server (NTRS)

Friesen, W. J.; Moore, J. A.

1973-01-01

Velocity-profile, pitot-pressure, and supplemental probe measurements were made at the nozzle exist of an expansion tunnel (a modification to the Langley pilot model expansion tube) for a nozzle net condition of a nitrogen test sample with a velocity of 4.5 km/sec and a density 0.005 times the density of nitrogen at standard conditions, both with the nozzle initially immersed in a helium atmosphere and with the nozzle initially evacuated. The purpose of the report is to present the results of these measurements and some of the physical properties of the nitrogen test sample which can be inferred from the measured results. The main conclusions reached are that: the velocity profiles differ for two nozzle conditions; regions of the flow field can be found where the velocity is uniform to within 5 percent and constant for several hundred microseconds; the velocity of the nitrogen test sample is reduced due to passage through the nozzle; and the velocity profiles do not significantly reflect the large variations which occur in the inferred density profiles.

Crystallographic Analysis of Fatigue Crack Initiation Behavior in Coarse-Grained Magnesium Alloy Under Tension-Tension Loading Cycles

NASA Astrophysics Data System (ADS)

Tamada, Kazuhiro; Kakiuchi, Toshifumi; Uematsu, Yoshihiko

2017-07-01

Plane bending fatigue tests are conducted to investigate fatigue crack initiation mechanisms in coarse-grained magnesium alloy, AZ31, under the stress ratios R = -1 and 0.1. The initial crystallographic structures are analyzed by an electron backscatter diffraction method. The slip or twin operation during fatigue tests is identified from the line angle analyses based on Euler angles of the grains. Under the stress ratio R = -1, relatively thick tension twin bands are formed in coarse grains. Subsequently, compression twin or secondary pyramidal slip operates within the tension twin band, resulting in the fatigue crack initiation. On the other hand, under R = 0.1 with tension-tension loading cycles, twin bands are formed on the specimen surface, but the angles of those bands do not correspond to tension twins. Misorientation analyses of c-axes in the matrix grain and twin band reveal that double twins are activated. Under R = 0.1, fatigue crack initiates along the double twin boundaries. The different manners of fatigue crack initiation at R = -1 and 0.1 are related to the asymmetricity of twining under tension and compression loadings. The fatigue strengths under different stress ratios cannot be estimated by the modified Goodman diagram due to the effect of stress ratio on crack initiation mechanisms.

Functional Outcome of Neurologic-Controlled HAL-Exoskeletal Neurorehabilitation in Chronic Spinal Cord Injury: A Pilot With One Year Treatment and Variable Treatment Frequency

PubMed Central

Schildhauer, Thomas A.; Meindl, Renate C.; Tegenthoff, Martin; Schwenkreis, Peter; Sczesny-Kaiser, Matthias; Grasmücke, Dennis; Fisahn, Christian; Aach, Mirko

2017-01-01

Study Design: Longitudinal prospective study. Objectives: Whether 1-year HAL-BWSTT of chronic spinal cord injured patients can improve independent ambulated mobility further as a function of training frequency, after an initial 3-month training period. Methods: Eight patients with chronic SCI were enrolled. They initially received full standard physical therapy and neurorehabilitation in the acute/subacute posttrauma phase. During this trial, all patients first underwent a daily (5 per week) HAL-BWSTT for 12 weeks. Subsequently, these patients performed a 40-week HAL-BWSTT with a training session frequency of either 1 or 3 to 5 sessions per week. The patients’ functional status including HAL-associated treadmill-walking time, -distance, and -speed with additional analysis of gait pattern, and their independent (without wearing the robot suit) functional mobility improvements, were assessed using the 10-Meter-Walk Test (10MWT), Timed-Up-and-Go Test (TUG) and 6-Minute-Walk Test (6MinWT) on admission, at 6 weeks, 12 weeks, and 1 year after enrollment. The data were analyzed separately for the 2 training frequency subgroups after the initial 12-week training period, which was identical in both groups. Results: During the 1-year follow-up, HAL-associated walking parameters and independent functional improvements were maintained in all the patients. This result held irrespective of the training frequency. Conclusions: Long-term 1-year maintenance of HAL-associated treadmill walking parameters and of improved independent walking abilities after initial 12 weeks of daily HAL-BWSTT is possible and depends mainly on the patients’ ambulatory status accomplished after initial training period. Subsequent regular weekly training, but not higher frequency training, seems to be sufficient to preserve the improvements accomplished. PMID:29238636

Risk factors for tuberculosis treatment failure, default, or relapse and outcomes of retreatment in Morocco

PubMed Central

2011-01-01

Background Patients with tuberculosis require retreatment if they fail or default from initial treatment or if they relapse following initial treatment success. Outcomes among patients receiving a standard World Health Organization Category II retreatment regimen are suboptimal, resulting in increased risk of morbidity, drug resistance, and transmission.. In this study, we evaluated the risk factors for initial treatment failure, default, or early relapse leading to the need for tuberculosis retreatment in Morocco. We also assessed retreatment outcomes and drug susceptibility testing use for retreatment patients in urban centers in Morocco, where tuberculosis incidence is stubbornly high. Methods Patients with smear- or culture-positive pulmonary tuberculosis presenting for retreatment were identified using clinic registries in nine urban public clinics in Morocco. Demographic and outcomes data were collected from clinical charts and reference laboratories. To identify factors that had put these individuals at risk for failure, default, or early relapse in the first place, initial treatment records were also abstracted (if retreatment began within two years of initial treatment), and patient characteristics were compared with controls who successfully completed initial treatment without early relapse. Results 291 patients presenting for retreatment were included; 93% received a standard Category II regimen. Retreatment was successful in 74% of relapse patients, 48% of failure patients, and 41% of default patients. 25% of retreatment patients defaulted, higher than previous estimates. Retreatment failure was most common among patients who had failed initial treatment (24%), and default from retreatment was most frequent among patients with initial treatment default (57%). Drug susceptibility testing was performed in only 10% of retreatment patients. Independent risk factors for failure, default, or early relapse after initial treatment included male gender (aOR = 2.29, 95% CI 1.10-4.77), positive sputum smear after 3 months of treatment (OR 7.14, 95% CI 4.04-13.2), and hospitalization (OR 2.09, 95% CI 1.01-4.34). Higher weight at treatment initiation was protective. Male sex, substance use, missed doses, and hospitalization appeared to be risk factors for default, but subgroup analyses were limited by small numbers. Conclusions Outcomes of retreatment with a Category II regimen are suboptimal and vary by subgroup. Default among patients receiving tuberculosis retreatment is unacceptably high in urban areas in Morocco, and patients who fail initial tuberculosis treatment are at especially high risk of retreatment failure. Strategies to address risk factors for initial treatment default and to identify patients at risk for failure (including expanded use of drug susceptibility testing) are important given suboptimal retreatment outcomes in these groups. PMID:21356062

Online Friendship, Romance, and Sex: Properties and Associations of the Online Relationship Initiation Scale.

PubMed

Harris, Keith M; Aboujaoude, Elias

2016-08-01

Online relationships are increasingly central to many people's lives. As a result, there is a growing need to scientifically examine their psychosocial implications. This study developed and tested the Online Relationship Initiation Scale (ORIS) through classical and item response theory analyses to address this need. An anonymous online survey included 713 adults, aged 18-71 years. The ORIS was tested on psychometric properties and examined for associations with gender and several standardized psychosocial measures. Results demonstrated unidimensionality of nine items, strong factor loadings, and high internal consistency (α = 0.90, ωt = 0.94). All items captured significant information on the latent trait and none showed differential item functioning by sex, age group, or ethnicity. General linear modeling confirmed hypotheses that men were more likely than women to initiate online relationships. Online relationship initiation was not strongly associated with perceived social support, but was positively related to financial distress, and willingness to engage in infidelity or unprotected sex. The ORIS was negatively associated with age and satisfaction with life and showed modest interactions with ethnicity and hours online. This study provided empirical evidence for an interpersonal relationship initiation construct. The ORIS was shown to be a psychometrically sound instrument for evaluating online interpersonal behaviors and their associations with psychosocial and demographic factors. Such psychometrically sound instruments can be useful in exploring online interpersonal behaviors and their significance.

Two-fluid 2.5D code for simulations of small scale magnetic fields in the lower solar atmosphere

NASA Astrophysics Data System (ADS)

Piantschitsch, Isabell; Amerstorfer, Ute; Thalmann, Julia Katharina; Hanslmeier, Arnold; Lemmerer, Birgit

2015-08-01

Our aim is to investigate magnetic reconnection as a result of the time evolution of magnetic flux tubes in the solar chromosphere. A new numerical two-fluid code was developed, which will perform a 2.5D simulation of the dynamics from the upper convection zone up to the transition region. The code is based on the Total Variation Diminishing Lax-Friedrichs method and includes the effects of ion-neutral collisions, ionisation/recombination, thermal/resistive diffusivity as well as collisional/resistive heating. What is innovative about our newly developed code is the inclusion of a two-fluid model in combination with the use of analytically constructed vertically open magnetic flux tubes, which are used as initial conditions for our simulation. First magnetohydrodynamic (MHD) tests have already shown good agreement with known results of numerical MHD test problems like e.g. the Orszag-Tang vortex test, the Current Sheet test or the Spherical Blast Wave test. Furthermore, the single-fluid approach will also be applied to the initial conditions, in order to compare the different rates of magnetic reconnection in both codes, the two-fluid code and the single-fluid one.

The views and experiences of nurses and midwives in the provision and management of provider-initiated HIV testing and counseling: a systematic review of qualitative evidence.

PubMed

Evans, Catrin; Nalubega, Sylivia; McLuskey, John; Darlington, Nicola; Croston, Michelle; Bath-Hextall, Fiona

2016-01-15

Global progress towards HIV prevention and care is contingent upon increasing the number of those aware of their status through HIV testing. Provider-initiated HIV testing and counseling is recommended globally as a strategy to enhance uptake of HIV testing and is primarily conducted by nurses and midwives. Research shows that provider-initiated HIV testing and counseling implementation is sub-optimal. The reasons for this are unclear. The review aimed to explore nurses' and midwives' views and experiences of the provision and management of provider-initiated HIV testing and counseling. All cadres of nurses and midwives were considered, including those who undertake routine HIV testing as part of a diverse role and those who are specifically trained as HIV counselors. Types of phenomenon of interest: The review sought to understand the views and experiences of the provision and management of provider-initiated HIV testing and counseling (including perceptions, opinions, beliefs, practices and strategies related to HIV testing and its implementation in practice). The review included only provider-initiated HIV testing and counseling. It excluded all other models of HIV testing. The review included all countries and all healthcare settings. Types of studies: This review considered all forms of qualitative study design and methodology. Qualitative elements of a mixed method study were included if they were presented separately within the publication. A three-step search strategy was utilized. Eight databases were searched for papers published from 1996 to October 2014, followed by hand searching of reference lists. Only studies published in the English language were considered. Methodological quality was assessed using the Qualitative Assessment and Review Instrument developed by the Joanna Briggs Institute. Qualitative findings were extracted using the Joanna Briggs Institute Qualitative Assessment and Review Instrument. Qualitative research findings were pooled using a pragmatic meta-aggregative approach and the Joanna Briggs Institute Qualitative Assessment and Review Instrument software. This review included 21 publications from 18 research studies, representing a wide range of countries and healthcare settings. There were 245 findings which were aggregated into 12 categories and five synthesized findings. 1. Nurses/midwives are supportive of provider-initiated HIV testing and counseling if it is perceived to enhance patient care and to align with perceived professional roles. 2. Nurses'/midwives' ability to perform provider-initiated HIV testing and counseling well requires an appropriate infrastructure and adequate human and material resources. 3. At the organizational level, nurses'/midwives' engagement with provider-initiated HIV testing and counseling is facilitated by an inclusive management structure, alongside the provision of ongoing training and clinical supervision. Provider-initiated HIV testing and counseling is hindered by difficulties in fitting it into existing workloads and routines. 4. Nurses/midwives perceive that good quality care in provider-initiated HIV testing and counseling involves finding a balance between public health needs and individual patient needs. Good care requires time and the ability to apply a patient centred approach. 5. The emotional work involved in provider-initiated HIV testing and counseling can be stressful. Nurses/Midwives may require support to deal with complex moral and ethical issues. This review shows that provider-initiated HIV testing and counseling is supported by nurses/midwives who strive to implement it according to principles of good care and a patient centered approach. Nurses/midwives face multiple operational, infra-structural, resource and ethical challenges in the implementation of provider-initiated HIV testing and counseling. The implementation process for provider-initiated HIV testing and counseling would benefit from using a quality improvement framework. Nurses/midwives undertaking provider-initiated HIV testing and counseling require management support, ongoing training and adequate infrastructure/resources. Additional guidance is required on legal/ethical issues in testing of children and in third party disclosure. Operational research is required to determine an optimal skill mix and optimal methods of integrating provider-initiated HIV testing and counseling into existing work routines. The Joanna Briggs Institute.

Consequences of germline variation disrupting the constitutional translational initiation codon start sites of MLH1 and BRCA2: use of potential alternative start sites and implications for predicting variant pathogenicity

PubMed Central

Parsons, Michael T.; Whiley, Phillip J.; Beesley, Jonathan; Drost, Mark; de Wind, Niels; Thompson, Bryony A.; Marquart, Louise; Hopper, John L.; Jenkins, Mark A.; Brown, Melissa A.; Tucker, Kathy; Warwick, Linda; Buchanan, Daniel D.; Spurdle, Amanda B.

2014-01-01

Variants that disrupt the translation initiation sequences in cancer predisposition genes are generally assumed to be deleterious. However few studies have validated these assumptions with functional and clinical data. Two cancer syndrome gene variants likely to affect native translation initiation were identified by clinical genetic testing: MLH1:c.1A>G p.(Met1?) and BRCA2:c.67+3A>G. In vitro GFP-reporter assays were conducted to assess the consequences of translation initiation disruption on alternative downstream initiation codon usage. Analysis of MLH1:c.1A>G p.(Met1?) showed that translation was mostly initiated at an in-frame position 103 nucleotides downstream, but also at two ATG sequences downstream. The protein product encoded by the in-frame transcript initiating from position c.103 showed loss of in vitro mismatch repair activity comparable to known pathogenic mutations. BRCA2:c.67+3A>G was shown by mRNA analysis to result in an aberrantly spliced transcript deleting exon 2 and the consensus ATG site. In the absence of exon 2, translation initiated mostly at an out-of-frame ATG 323 nucleotides downstream, and to a lesser extent at an in-frame ATG 370 nucleotides downstream. Initiation from any of the downstream alternative sites tested in both genes would lead to loss of protein function, but further clinical data is required to confirm if these variants are associated with a high cancer risk. Importantly, our results highlight the need for caution in interpreting the functional and clinical consequences of variation that leads to disruption of the initiation codon, since translation may not necessarily occur from the first downstream alternative start site, or from a single alternative start site. PMID:24302565

Integrated corridor management initiative : demonstration phase evaluation, San Diego technical capability analysis test plan.

DOT National Transportation Integrated Search

1998-11-01

The purpose of this working paper is to present estimates of potential safety benefits resulting from full implementation of Intelligent Transportation Systems (ITS) in the United States. These estimates were derived by integrating results from a num...

LWH and ACH Helmet Hardware Study

DTIC Science & Technology

2015-11-30

initial attempts to perform impact tests using screws mounted in Kevlar composite panels resulted in little damage to the screws, but a lot of...stiffer and stronger than Kevlar panels, does not plastically deform (and therefore Figure 11. Typical ductile fracture surface resulting from a

10 CFR 26.95 - Conducting an initial test for alcohol using a breath specimen.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Conducting an initial test for alcohol using a breath specimen. 26.95 Section 26.95 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.95 Conducting an initial test for alcohol using a breath specimen. (a) The...

10 CFR 26.95 - Conducting an initial test for alcohol using a breath specimen.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Conducting an initial test for alcohol using a breath specimen. 26.95 Section 26.95 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.95 Conducting an initial test for alcohol using a breath specimen. (a) The...

10 CFR 26.95 - Conducting an initial test for alcohol using a breath specimen.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Conducting an initial test for alcohol using a breath specimen. 26.95 Section 26.95 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.95 Conducting an initial test for alcohol using a breath specimen. (a) The...

10 CFR 26.95 - Conducting an initial test for alcohol using a breath specimen.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Conducting an initial test for alcohol using a breath specimen. 26.95 Section 26.95 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.95 Conducting an initial test for alcohol using a breath specimen. (a) The...

10 CFR 26.95 - Conducting an initial test for alcohol using a breath specimen.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Conducting an initial test for alcohol using a breath specimen. 26.95 Section 26.95 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.95 Conducting an initial test for alcohol using a breath specimen. (a) The...

Results Of Initial Analyses Of The Salt (Macro) Batch 9 Tank 21H Qualification Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T.

2015-10-08

Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Interim Salt Disposition Project (ISDP) Salt (Macro) Batch 9 for processing through the Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU). This document reports the initial results of the analyses of samples of Tank 21H. Analysis of the Tank 21H Salt (Macro) Batch 9 composite sample indicates that the material does not display any unusual characteristics. Further results on the chemistry and other tests will be issued in the future.

Detecting Initiation or Risk for Initiation of Substance Use before High School during Pediatric Well-Child Check-Ups

PubMed Central

Ridenour, Ty A.; Willis, David; Bogen, Debra L.; Novak, Scott; Scherer, Jennifer; Reynolds, Maureen D.; Zhai, Zu Wei; Tarter, Ralph E.

2015-01-01

Background Youth substance use (SU) is prevalent and costly, affecting mental and physical health. American Academy of Pediatrics and Affordable Care Act call for SU screening and prevention. The Youth Risk Index© (YRI) was tested as a screening tool for having initiated and propensity to initiate SU before high school (which forecasts SU disorder). YRI was hypothesized to have good to excellent psychometrics, feasibility and stakeholder acceptability for use during well-child check-ups. Design A high-risk longitudinal design with two cross-sectional replication samples, ages 9–13 was used. Analyses included receiver operating characteristics and regression analyses. Participants A one-year longitudinal sample (N=640) was used for YRI derivation. Replication samples were a cross-sectional sample (N=345) and well-child check-up patients (N=105) for testing feasibility, validity and acceptability as a screening tool. Results YRI has excellent test-retest reliability and good sensitivity and specificity for concurrent and one-year-later SU (odds ratio=7.44 CI=4.3–13.0) and conduct problems (odds ratios=7.33 CI=3.9–13.7). Results were replicated in both cross-sectional samples. Well-child patients, parents and pediatric staff rated YRI screening as important, acceptable, and a needed service. Conclusions Identifying at-risk youth prior to age 13 could reap years of opportunity to intervene before onset of SU disorder. Most results pertained to YRI’s association with concurrent or recent past risky behaviors; further replication ought to specify its predictive validity, especially adolescent-onset risky behaviors. YRI well identifies youth at risk for SU and conduct problems prior to high school, is feasible and valid for screening during well-child check-ups, and is acceptable to stakeholders. PMID:25765481

Plasma Discharge Initiation of Explosives in Rock Blasting Application: A Case Study

NASA Astrophysics Data System (ADS)

Jae-Ou, Chae; Young-Jun, Jeong; V, M. Shmelev; A, A. Denicaev; V, M. Poutchkov; V, Ravi

2006-07-01

A plasma discharge initiation system for the explosive volumetric combustion charge was designed, investigated and developed for practical application. Laboratory scale experiments were carried out before conducting the large scale field tests. The resultant explosions gave rise to less noise, insignificant seismic vibrations and good specific explosive consumption for rock blasting. Importantly, the technique was found to be safe and environmentally friendly.

Beauty and the beast: results of the Rhode Island smokefree shop initiative.

PubMed

Linnan, Laura A; Emmons, Karen M; Abrams, David B

2002-01-01

Licensed hairdressing facilities are prevalent in communities nationwide and represent a unique and promising channel for delivering public health interventions. The Rhode Island Smokefree Shop Initiative tested the feasibility of using these facilities to deliver smoking policy interventions statewide. A statewide survey of hairdressing facilities was followed by interventions targeted to the readiness level (high/low) of respondents to adopt smoke-free policies.

Experimental Investigation of Shock Initiation in Mixtures of Manganese and Sulfur

NASA Astrophysics Data System (ADS)

Jetté, F. X.; Goroshin, S.; Higgins, A. J.

2009-12-01

Equimolar mixtures of manganese powder and sulfur at different starting densities were tested in two different types of steel recovery capsules in order to study the shock initiation phenomenon in Self-Propagating High-Temperature Synthesis (SHS) mixtures. Two different sizes of Mn particles were used for these experiments, <10 μm and -325 mesh (<44 μm). This mixture was selected due to the large exothermic heat release of the manganese-sulfur reaction (214 kJ/mol), which causes the reaction to be self-sustaining once initiated. The test samples were placed in planar recovery capsules and a strong shock was delivered via the detonation of a charge of amine-sensitized nitromethane. Various shock strengths were achieved by placing different thicknesses of PMMA attenuator discs between the explosive charge and the capsule. The results confirmed that shock-induced reactions can be produced in highly non-porous mixtures. It was also found that shock interactions with the side walls of the recovery capsule can play a significant role in the initiation.

Development and Testing of a USM High Altitude Balloon

NASA Astrophysics Data System (ADS)

Thaheer, A. S. Mohamed; Ismail, N. A.; Yusoff, S. H. Md.; Nasirudin, M. A.

2018-04-01

This paper discusses on tests conducted on the component and subsystem level during development of the USM High Altitude Balloon (HAB). The tests conducted by selecting initial components then tested individually based on several case studies such as reliability test, camera viewing, power consumption, thermal capability, and parachute performance. Then, the component is integrated into sub-system level for integration and functionality test. The preliminary result is utilized to tune the components and sub-systems and trial launch is conducted where the sample images are recorded and atmospheric data successfully collected.

MEASURING SPORT-SPECIFIC PHYSICAL ABILITIES IN MALE GYMNASTS: THE MEN'S GYMNASTICS FUNCTIONAL MEASUREMENT TOOL

PubMed Central

Kenyon, Lisa K.; Elliott, James M; Cheng, M. Samuel

2016-01-01

Purpose/Background Despite the availability of various field-tests for many competitive sports, a reliable and valid test specifically developed for use in men's gymnastics has not yet been developed. The Men's Gymnastics Functional Measurement Tool (MGFMT) was designed to assess sport-specific physical abilities in male competitive gymnasts. The purpose of this study was to develop the MGFMT by establishing a scoring system for individual test items and to initiate the process of establishing test-retest reliability and construct validity. Methods A total of 83 competitive male gymnasts ages 7-18 underwent testing using the MGFMT. Thirty of these subjects underwent re-testing one week later in order to assess test-retest reliability. Construct validity was assessed using a simple regression analysis between total MGFMT scores and the gymnasts’ USA-Gymnastics competitive level to calculate the coefficient of determination (r2). Test-retest reliability was analyzed using Model 1 Intraclass correlation coefficients (ICC). Statistical significance was set at the p<0.05 level. Results The relationship between total MGFMT scores and subjects’ current USA-Gymnastics competitive level was found to be good (r2 = 0.63). Reliability testing of the MGFMT composite test score showed excellent test-retest reliability over a one-week period (ICC = 0.97). Test-retest reliability of the individual component tests ranged from good to excellent (ICC = 0.75-0.97). Conclusions The results of this study provide initial support for the construct validity and test-retest reliability of the MGFMT. Level of Evidence Level 3 PMID:27999723

Initiation of Insensitive High Explosives Using Multiple Wave Interactions

NASA Astrophysics Data System (ADS)

Francois, Elizabeth

Insensitive High Explosives (IHEs) increase safety in many types of weapons. However, the safety comes at the cost of performance. Initiation of IHE requires large boosters and powerful detonators as well. Multipoint initiation is being utilized to exploit explosive wave interactions to create overdriven states, greatly facilitating the initiation of IHEs. This presentation will focus on recent explosive experiments where the minimum spot size for single-point initiation in PBX 9502 was determined. Below this threshold, PBX 9502 could not be initiated. This was then expanded to three initiation points, which were smaller this threshold. Measurements of the velocity and pressure of the wave interactions were measured using Photon Doppler Velocimetry (PDV). Initiation was observed, and the resulting pressures at the double and triple points were found to be above the CJ state for PBX 9502. Further testing will be performed using cutback experiments to isolate the overdriven state, and quantify the duration of the phenomenon.

Increases in Recent HIV Testing Among Men Who Have Sex With Men Coincide With the Centers for Disease Control and Prevention's Expanded Testing Initiative

PubMed Central

Cooley, Laura A.; Wejnert, Cyprian; Rose, Charles E.; Paz-Bailey, Gabriela; Taussig, Jennifer; Gern, Robert; Hoyte, Tamika; Salazar, Laura; White, Jianglan; Todd, Jeff; Bautista, Greg; Flynn, Colin; Sifakis, Frangiscos; German, Danielle; Isenberg, Debbie; Driscoll, Maura; Hurwitz, Elizabeth; Doherty, Rose; Wittke, Chris; Prachand, Nikhil; Benbow, Nanette; Melville, Sharon; Pannala, Praveen; Yeager, Richard; Sayegh, Aaron; Dyer, Jim; Sheu, Shane; Novoa, Alicia; Thrun, Mark; Al-Tayyib, Alia; Wilmoth, Ralph; Higgins, Emily; Griffin, Vivian; Mokotoff, Eve; MacMaster, Karen; Wolverton, Marcia; Risser, Jan; Rehman, Hafeez; Padgett, Paige; Bingham, Trista; Sey, Ekow Kwa; LaLota, Marlene; Metsch, Lisa; Forrest, David; Beck, Dano; Cardenas, Gabriel; Nemeth, Chris; Anderson, Bridget J.; Watson, Carol-Ann; Smith, Lou; Robinson, William T.; Gruber, DeAnn; Barak, Narquis; Murrill, Chris; Neaigus, Alan; Jenness, Samuel; Hagan, Holly; Reilly, Kathleen H.; Wendel, Travis; Cross, Helene; Bolden, Barbara; D'Errico, Sally; Wogayehu, Afework; Godette, Henry; Brady, Kathleen A.; Kirkland, Althea; Sifferman, Andrea; Miguelino-Keasling, Vanessa; Velasco, Al; Tovar, Veronica; Raymond, H. Fisher; De León, Sandra Miranda; Rolón-Colón, Yadira; Marzan, Melissa; Courogen, Maria; Jaenicke, Tom; Thiede, Hanne; Burt, Richard; Jia, Yujiang; Opoku, Jenevieve; Sansone, Marie; West, Tiffany; Magnus, Manya; Kuo, Irene

2015-01-01

According to National HIV Behavioral Surveillance system data, human immunodeficiency virus (HIV) testing increased among gay, bisexual, and other men who have sex with men from 2008 to 2011 in cities funded by the Centers for Disease Control and Prevention's Expanded Testing Initiative, suggesting that focused HIV testing initiatives might have positive effects. PMID:25352589

WITHDRAWN: Initial management strategies for dyspepsia.

PubMed

Delaney, Brendan; Ford, Alex C; Forman, David; Moayyedi, Paul; Qume, Michelle

2009-10-07

This review considers management strategies (combinations of initial investigation and empirical treatments) for dyspeptic patients. Dyspepsia was defined to include both epigastric pain and heartburn. To determine the effectiveness, acceptability, and cost effectiveness of the following initial management strategies for patients presenting with dyspepsia (a) Initial pharmacological therapy (including endoscopy for treatment failures). (b) Early endoscopy. (c) Testing for Helicobacter pylori (H. pylori )and endoscope only those positive. (d) H. pylori eradication therapy with or without prior testing. Trials were located through electronic searches and extensive contact with trialists. All randomised controlled trials of dyspeptic patients presenting in primary care. Data were collected on dyspeptic symptoms, quality of life and use of resources. An individual patient data meta-analysis of health economic data was conducted Twenty-five papers reporting 27 comparisons were found. Trials comparing proton pump inhibitors (PPI) with antacids (three trials) and histamine H2-receptor antagonists (H2RAs) (three trials), early endoscopy with initial acid suppression (five trials), H. pylori test and endoscope versus usual management (three trials), H. pylori test and treat versus endoscopy (six trials), and test and treat versus acid suppression alone in H. pylori positive patients (four trials), were pooled. PPIs were significantly more effective than both H2RAs and antacids. Relative risks (RR) and 95% confidence intervals (CI) were; for PPI compared with antacid 0.72 (95% CI 0.64 to 0.80), PPI compared with H2RA 0.63 (95% CI 0.47 to 0.85). Results for other drug comparisons were either absent or inconclusive. Initial endoscopy was associated with a small reduction in the risk of recurrent dyspeptic symptoms compared with H. pylori test and treat (OR 0.75, 95% CI 0.58 to 0.96), but was not cost effective (mean additional cost of endoscopy US$401 (95% CI $328 to 474). Test and treat may be more effective than acid suppression alone (RR 0.59 95% CI 0.42 to 0.83). Proton pump inhibitor drugs (PPIs) are effective in the treatment of dyspepsia in these trials which may not adequately exclude patients with gastro-oesophageal reflux disease (GORD). The relative efficacy of histamine H2-receptor antagonists (H2RAs) and PPIs is uncertain. Early investigation by endoscopy or H. pylori testing may benefit some patients with dyspepsia but is not cost effective as part of an overall management strategy.

An UHF Frequency-Modulated Continuous Wave Wind Profiler - Development and Initial Results

DTIC Science & Technology

2009-09-01

proposed and tested . The current design stage and performance of the cancellation loop, and the need of a new design for the IF section, suggest that some of...contrued as an official Department of the Army position, policy or decision, unless so designated by other documentation. 12. DISTRIBUTION...development of each of its subsystems, the laboratory tests performed to evaluate their performance, and the results of the first field deployment

Summary of NASA/DOE Aileron-Control Development Program for Wind Turbines

NASA Technical Reports Server (NTRS)

Miller, D. R.

1986-01-01

The development of aileron-control for wind turbines is discussed. Selected wind tunnel test results and full-scale rotor test results are presented for various types of ailerons. Finally, the current status of aileron-control development is discussed. Aileron-control was considered as a method of rotor control for use on wind turbines based on its potential to reduce rotor weight and cost. Following an initial feasibility study, a 20 percent chord aileron-control rotor was fabricated and tested on the NASA/DOE Mod-0 experimental wind turbine. Results from these tests indicated that the 20 percent chord ailerons regulated power and provided overspeed protection, but only over a very limited windspeed range. The next aileron-control rotor to be tested on the Mod-0 had 38 percent chord ailerons and test results showed these ailerons provided overspeed protection and power regulation over the Mod-0's entire operational windspeed range.

14 CFR 33.90 - Initial maintenance inspection test.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Initial maintenance inspection test. 33.90 Section 33.90 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.90 Initial maintenance...

14 CFR 33.90 - Initial maintenance inspection test.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Initial maintenance inspection test. 33.90 Section 33.90 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.90 Initial maintenance...

14 CFR 33.90 - Initial maintenance inspection test.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Initial maintenance inspection test. 33.90 Section 33.90 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.90 Initial maintenance...

14 CFR 33.90 - Initial maintenance inspection test.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Initial maintenance inspection test. 33.90 Section 33.90 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.90 Initial maintenance...

Model systems for defining initiation, promotion, and progression of skin neoplasms.

PubMed

Boutwell, R K

1989-01-01

A number of items that must be considered in designing and choosing a suitable model for initiation and promotion testing have been described. Although these items may seem complex, tests for initiation and promotion are, in reality, quite simple and provide a rational approach to carcinogen testing. Several tests have been described here and Eastin, elsewhere in this book, describes the validation of a simple and highly recommended test. The processes involved in initiation and promotion are qualitatively different. The criteria for concern about possible human hazards as well as for regulation of initiators and promoters should be based on these qualitative differences. Realistic appraisal of the risk must be based on the level and nature of the potential hazard. In particular, it must be recognized that promoting action is reversible, that a threshold exists, and that promotion is readily inhibited. Therefore, animal tests that differentiate between potential initiators and promoters are essential to enable a logical assessment of human risk and the implementation of appropriate protective measures based on scientific facts.

Regulatory focus as a mediator of the influence of initiating structure and servant leadership on employee behavior.

PubMed

Neubert, Mitchell J; Kacmar, K Michele; Carlson, Dawn S; Chonko, Lawrence B; Roberts, James A

2008-11-01

In this research, the authors test a model in which the regulatory focus of employees at work mediates the influence of leadership on employee behavior. In a nationally representative sample of 250 workers who responded over 2 time periods, prevention focus mediated the relationship of initiating structure to in-role performance and deviant behavior, whereas promotion focus mediated the relationship of servant leadership to helping and creative behavior. The results indicate that even though initiating structure and servant leadership share some variance in explaining other variables, each leadership style incrementally predicts disparate outcomes after controlling for the other style and dispositional tendencies. A new regulatory focus scale, the Work Regulatory Focus (WRF) Scale, also was developed and initially validated for this study. Implications for the results and the WRF Scale are discussed.

Performance of the QuantiFERON-TB Gold Assay Among HIV-infected Children With Active Tuberculosis in France.

PubMed

Hormi, Myriam; Guérin-El Khourouj, Valérie; Pommelet, Virginie; Jeljeli, Mohamed; Pédron, Béatrice; Diana, Jean-Sébastien; Faye, Albert; Sterkers, Ghislaine

2018-04-01

Data regarding the use of QuantiFERON to assist the diagnosis of active tuberculosis (TB) in HIV-infected children are limited, especially in countries with low incidence of TB/HIV coinfection. QuantiFERON results were analyzed in 63 HIV-infected children who presented to our hospital in Paris, France. Seventeen HIV-uninfected children with active TB (4 culture-confirmed) were included for comparison. The 63 HIV-infected children (median age: 11 yr) had 113 QuantiFERON tests. Thirty-four (54%) were born in sub-Saharan Africa. Vertical HIV transmission was documented for 50 of 52 (96%) and stage III HIV-infection for 30 of 50 children (60%). Over the study period, active TB was diagnosed in 7 of 63 HIV-infected children (3 culture-confirmed). Additional ongoing or previous opportunistic infections were present in 4 of 7. QuantiFERON results were positive in 2 of 7 HIV-infected children with active TB (sensitivity: 29%) and 16 of 17 HIV-uninfected children with active TB (sensitivity: 94%). At initial QuantiFERON testing of the 63 HIV-infected children, 8 (13%) had positive results (1, active TB; 5, latent TB; 2, previous TB) and 51 (81%) had negative results. Of 33 children with repeat testing after an initially positive or negative result, the only change was one conversion from a negative to a positive result at the onset of active TB. The 4 children (6%) with indeterminate quantiFERON results had a concomitant opportunistic infection. Results of repeat testing after clinical stabilization were negative in all 4. QuantiFERON testing performed poorly for active TB diagnosis in this series of children with advanced HIV infection.

Care Cascade for targeted tuberculosis testing and linkage to Care in Homeless Populations in the United States: a meta-analysis.

PubMed

Parriott, Andrea; Malekinejad, Mohsen; Miller, Amanda P; Marks, Suzanne M; Horvath, Hacsi; Kahn, James G

2018-04-12

Homelessness increases the risk of tuberculosis (TB) disease and latent TB infection (LTBI), but persons experiencing homelessness often lack access to testing and treatment. We assessed the yield of TB testing and linkage to care for programs targeting homeless populations in the United States. We conducted a comprehensive search of peer-reviewed and grey literature, adapting Cochrane systematic review methods. Two reviewers independently assessed study eligibility and abstracted key data on the testing to care cascade: number of persons reached, recruited for testing, tested for LTBI, with valid test results, referred to follow-up care, and initiating care. We used random effects to calculate pooled proportions and 95% confidence intervals (CI) of persons retained in each step via inverse-variance weighted meta-analysis, and cumulative proportions as products of adjacent step proportions. We identified 23 studies published between 1986 and 2014, conducted in 12 states and 15 cities. Among studies using tuberculin skin tests (TST) we found that 93.7% (CI 72.4-100%) of persons reached were recruited, 97.9% (89.3-100%) of those recruited had tests placed, 85.5% (78.6-91.3%) of those with tests placed returned for reading, 99.9% (99.6-100%) of those with tests read had valid results, and 24.7% (21.0-28.5%) with valid results tested positive. All persons testing positive were referred to follow-up care, and 99.8% attended at least one session of follow-up care. Heterogeneity was high for most pooled proportions. For a hypothetical cohort of 1000 persons experiencing homelessness reached by a targeted testing program using TST, an estimated 917 were tested, 194 were positive, and all of these initiated follow-up care. Targeted TB testing of persons experiencing homelessness appears effective in detecting LTBI and connecting persons to care and potential treatment. Future evaluations should assess diagnostic use of interferon gamma release assays and completion of treatment, and costs of testing and treatment.

Alternatives to ozone depleting refrigerants in test equipment

NASA Technical Reports Server (NTRS)

Hall, Richard L.; Johnson, Madeleine R.

1995-01-01

This paper describes the initial results of a refrigerant retrofit project at the Aerospace Guidance and Metrology Center (AGMC) at Newark Air Force Base, Ohio. The objective is to convert selected types of test equipment to properly operate on hydrofluorocarbon (HFC) alternative refrigerants, having no ozone depleting potential, without compromising system reliability or durability. This paper discusses the primary technical issues and summarizes the test results for 17 different types of test equipment: ten environmental chambers, two ultralow temperature freezers, two coolant recirculators, one temperature control unit, one vapor degreaser, and one refrigerant recovery system. The postconversion performance test results have been very encouraging: system capacity and input power remained virtually unchanged. In some cases, the minimum operating temperature increased by a few degrees as a result of the conversion, but never beyond AGMC's functional requirements.

Eucalyptus Energy Farm: feasibility study and demonstration. Phase 1: site and species selection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mariani, E.O.; Wood, W.A.; Kouchoukos, P.C.

1978-06-01

The results of investigations to determine the feasibility for establishing ''Eucalyptus Energy Farms'' as a potential source of biomass derived energy are presented. Included in this report are: the results of an extensive literature search and numerous field interviews (both domestically and internationally) to identify those Eucalyptus species most suitable for use within the United States; a description of the site selection criteria, site selection process, and identification of potential sites for use in testing the Eucalyptus Energy Farm concept; a description of the Eucalyptus species selection criteria, species selection process, and an identification of the specific species recommended formore » testing at specific sites; preliminary engineering designs for each of the proposed plantation sites; and environmental impact considerations related to Eucalyptus growing. It is concluded that although the Eucalyptus are extremely temperature sensitive and the geographic areas which appear suitable for their planting (within the United States) are principally confined to western and central California and the warmest regions of the southeastern United States, each of the areas contain large amounts of marginal land which could be converted into Eucalyptus based biomass plantations. Suitable sites, which are representative of the larger marginal land areas, are immediately available for use in establishing Eucalyptus screening test sites. Furthermore, there are not significant environmental conditions which would preclude the establishment of these initial test sites. It is therefore recommended that efforts be initiated to obtain selected provenances of Eucalyptus seeds (of the designated species) for further field testing and data collection within the United States, and that actual site selection be initiated.« less

Recycle of Zirconium from Used Nuclear Fuel Cladding: A Major Element of Waste Reduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collins, Emory D; DelCul, Guillermo D; Terekhov, Dmitri

2011-01-01

Feasibility tests were initiated to determine if the zirconium in commercial used nuclear fuel (UNF) cladding can be recovered in sufficient purity to permit re-use, and if the recovery process can be operated economically. Initial tests are being performed with unirradiated, non-radioactive samples of various types of Zircaloy materials that are used in UNF cladding to develop the recovery process and determine the degree of purification that can be obtained. Early results indicate that quantitative recovery can be accomplished and product contamination with alloy constituents can be controlled sufficiently to meet purification requirements. Future tests with actual radioactive UNF claddingmore » are planned. The objective of current research is to determine the feasibility of recovery and recycle of zirconium from used fuel cladding wastes. Zircaloy cladding, which contains 98+% of hafnium-free zirconium, is the second largest mass, on average {approx}25 wt %, of the components in used U.S. light-water-reactor fuel assemblies. Therefore, recovery and recycle of the zirconium would enable a large reduction in geologic waste disposal for advanced fuel cycles. Current practice is to compact or grout the cladding waste and store it for subsequent disposal in a geologic repository. This paper describes results of initial tests being performed with unirradiated, non-radioactive samples of various types of Zircaloy materials that are used in UNF cladding to develop the recovery process and determine the degree of purification that can be obtained. Future tests with actual radioactive UNF cladding are planned.« less

Non-Destructive Current Sensing for Energy Efficiency Monitoring in Buildings with Environmental Certification

PubMed Central

Mota, Lia Toledo Moreira; Mota, Alexandre de Assis; Coiado, Lorenzo Campos

2015-01-01

Nowadays, buildings environmental certifications encourage the implementation of initiatives aiming to increase energy efficiency in buildings. In these certification systems, increased energy efficiency arising from such initiatives must be demonstrated. Thus, a challenge to be faced is how to check the increase in energy efficiency related to each of the employed initiatives without a considerable building retrofit. In this context, this work presents a non-destructive method for electric current sensing to assess implemented initiatives to increase energy efficiency in buildings with environmental certification. This method proposes the use of a sensor that can be installed directly in the low voltage electrical circuit conductors that are powering the initiative under evaluation, without the need for reforms that result in significant costs, repair, and maintenance. The proposed sensor consists of three elements: an air-core transformer current sensor, an amplifying/filtering stage, and a microprocessor. A prototype of the proposed sensor was developed and tests were performed to validate this sensor. Based on laboratory tests, it was possible to characterize the proposed current sensor with respect to the number of turns and cross-sectional area of the primary and secondary coils. Furthermore, using the Least Squares Method, it was possible to determine the efficiency of the air core transformer current sensor (the best efficiency found, considering different test conditions, was 2%), which leads to a linear output response. PMID:26184208

Non-Destructive Current Sensing for Energy Efficiency Monitoring in Buildings with Environmental Certification.

PubMed

Mota, Lia Toledo Moreira; Mota, Alexandre de Assis; Coiado, Lorenzo Campos

2015-07-10

Nowadays, buildings environmental certifications encourage the implementation of initiatives aiming to increase energy efficiency in buildings. In these certification systems, increased energy efficiency arising from such initiatives must be demonstrated. Thus, a challenge to be faced is how to check the increase in energy efficiency related to each of the employed initiatives without a considerable building retrofit. In this context, this work presents a non-destructive method for electric current sensing to assess implemented initiatives to increase energy efficiency in buildings with environmental certification. This method proposes the use of a sensor that can be installed directly in the low voltage electrical circuit conductors that are powering the initiative under evaluation, without the need for reforms that result in significant costs, repair, and maintenance. The proposed sensor consists of three elements: an air-core transformer current sensor, an amplifying/filtering stage, and a microprocessor. A prototype of the proposed sensor was developed and tests were performed to validate this sensor. Based on laboratory tests, it was possible to characterize the proposed current sensor with respect to the number of turns and cross-sectional area of the primary and secondary coils. Furthermore, using the Least Squares Method, it was possible to determine the efficiency of the air core transformer current sensor (the best efficiency found, considering different test conditions, was 2%), which leads to a linear output response.

Optimizing multiple-choice tests as tools for learning.

PubMed

Little, Jeri L; Bjork, Elizabeth Ligon

2015-01-01

Answering multiple-choice questions with competitive alternatives can enhance performance on a later test, not only on questions about the information previously tested, but also on questions about related information not previously tested-in particular, on questions about information pertaining to the previously incorrect alternatives. In the present research, we assessed a possible explanation for this pattern: When multiple-choice questions contain competitive incorrect alternatives, test-takers are led to retrieve previously studied information pertaining to all of the alternatives in order to discriminate among them and select an answer, with such processing strengthening later access to information associated with both the correct and incorrect alternatives. Supporting this hypothesis, we found enhanced performance on a later cued-recall test for previously nontested questions when their answers had previously appeared as competitive incorrect alternatives in the initial multiple-choice test, but not when they had previously appeared as noncompetitive alternatives. Importantly, however, competitive alternatives were not more likely than noncompetitive alternatives to be intruded as incorrect responses, indicating that a general increased accessibility for previously presented incorrect alternatives could not be the explanation for these results. The present findings, replicated across two experiments (one in which corrective feedback was provided during the initial multiple-choice testing, and one in which it was not), thus strongly suggest that competitive multiple-choice questions can trigger beneficial retrieval processes for both tested and related information, and the results have implications for the effective use of multiple-choice tests as tools for learning.

Effects of Two Physical Training Paradigms on Biological and Cognitive Characteristics of Airmen: Lessons Learned

DTIC Science & Technology

2017-06-07

a 9- week physical training program, tests of physical endurance and strength , body composition analyses, biomarker collections, and cognitive tests...BDNF results to improving training , a new laboratory capability within RHCP was needed, coupled with an initial operational pilot test of that...traditional AF fitness training and that the improvements in cognitive performance would be correlated with changes in BDNF levels. Specifically, the

An Examination of the Perceived Importance of Technical Competence in Acquisition Project Management

DTIC Science & Technology

1991-09-01

Develop (First Draft) Instructions Critique (Revision) Answerability Pilot Test (Second Draft) Analysis Response Mode Revision Useability Preparation...appropriate questionnaire items. Initially, the set of questions developed for the study reflected a few shortcomings. A pilot test of the first draft among...resulted. First, feedback from the pilot test indicated a need to reduce the completion time. Because the multiple choice format required several

Incremental rate of prefrontal oxygenation determines performance speed during cognitive Stroop test: the effect of ageing.

PubMed

Endo, Kana; Liang, Nan; Idesako, Mitsuhiro; Ishii, Kei; Matsukawa, Kanji

2018-02-19

Cognitive function declines with age. The underlying mechanisms responsible for the deterioration of cognitive performance, however, remain poorly understood. We hypothesized that an incremental rate of prefrontal oxygenation during a cognitive Stroop test decreases in progress of ageing, resulting in a slowdown of cognitive performance. To test this hypothesis, we identified, using multichannel near-infrared spectroscopy, the characteristics of the oxygenated-hemoglobin concentration (Oxy-Hb) responses of the prefrontal cortex to both incongruent Stroop and congruent word-reading test. Spatial distributions of the significant changes in the three components (initial slope, peak amplitude, and area under the curve) of the Oxy-Hb response were compared between young and elderly subjects. The Stroop interference time (as a difference in total periods for executing Stroop and word-reading test, respectively) approximately doubled in elderly as compared to young subjects. The Oxy-Hb in the rostrolateral, but not caudal, prefrontal cortex increased during the Stroop test in both age groups. The initial slope of the Oxy-Hb response, rather than the peak and area under the curve, had a strong correlation with cognitive performance speed. Taken together, it is likely that the incremental rate of prefrontal oxygenation may decrease in progress of ageing, resulting in a decline in cognitive performance.

Effect of initial contact surface condition on the friction and wear properties of bearing steel in cyclic reciprocating sliding contact

NASA Astrophysics Data System (ADS)

Tanaka, Y.; Endo, M.; Moriyama, S.

2017-05-01

Delamination failure is one of the most important engineering problems. This failure can frequently be detrimental to rolling contact machine elements such as bearings, gear wheels, etc. This phenomenon, called rolling contact fatigue, has a close relationship not only with opening-mode but also with shear-mode fatigue crack growth. The crack face interference is known to significantly affect the shear-mode fatigue crack propagation and its threshold behavior. Quantitative investigation on friction and wear at fatigue crack faces in the material is essentially impossible. Previously, thus, a novel ring-on-ring test by making use of fatigue testing machine was proposed to simulate a cyclic reciprocating sliding contact of crack surfaces. However, this test procedure had some problems. For instance, in order to achieve the uniform contact at the start of test, the rubbing of specimens must be conducted in advance. By this treatment, the specimen surfaces were already damaged before the test. In this study, an improvement of experimental method was made to perform the test using the damage-free specimens. The friction and wear properties for heat-treated high carbon-chromium bearing steel were investigated with this new method and the results were compared to the results obtained by using the initially damaged specimens.

ArrayInitiative - a tool that simplifies creating custom Affymetrix CDFs

PubMed Central

2011-01-01

Background Probes on a microarray represent a frozen view of a genome and are quickly outdated when new sequencing studies extend our knowledge, resulting in significant measurement error when analyzing any microarray experiment. There are several bioinformatics approaches to improve probe assignments, but without in-house programming expertise, standardizing these custom array specifications as a usable file (e.g. as Affymetrix CDFs) is difficult, owing mostly to the complexity of the specification file format. However, without correctly standardized files there is a significant barrier for testing competing analysis approaches since this file is one of the required inputs for many commonly used algorithms. The need to test combinations of probe assignments and analysis algorithms led us to develop ArrayInitiative, a tool for creating and managing custom array specifications. Results ArrayInitiative is a standalone, cross-platform, rich client desktop application for creating correctly formatted, custom versions of manufacturer-provided (default) array specifications, requiring only minimal knowledge of the array specification rules and file formats. Users can import default array specifications, import probe sequences for a default array specification, design and import a custom array specification, export any array specification to multiple output formats, export the probe sequences for any array specification and browse high-level information about the microarray, such as version and number of probes. The initial release of ArrayInitiative supports the Affymetrix 3' IVT expression arrays we currently analyze, but as an open source application, we hope that others will contribute modules for other platforms. Conclusions ArrayInitiative allows researchers to create new array specifications, in a standard format, based upon their own requirements. This makes it easier to test competing design and analysis strategies that depend on probe definitions. Since the custom array specifications are easily exported to the manufacturer's standard format, researchers can analyze these customized microarray experiments using established software tools, such as those available in Bioconductor. PMID:21548938

Serial testing for latent tuberculosis using QuantiFERON-TB Gold In-Tube: A Markov model

PubMed Central

Moses, Mark W.; Zwerling, Alice; Cattamanchi, Adithya; Denkinger, Claudia M.; Banaei, Niaz; Kik, Sandra V.; Metcalfe, John; Pai, Madhukar; Dowdy, David

2016-01-01

Healthcare workers (HCWs) in low-incidence settings are often serially tested for latent TB infection (LTBI) with the QuantiFERON-TB Gold In-Tube (QFT) assay, which exhibits frequent conversions and reversions. The clinical impact of such variability on serial testing remains unknown. We used a microsimulation Markov model that accounts for major sources of variability to project diagnostic outcomes in a simulated North American HCW cohort. Serial testing using a single QFT with the recommended conversion cutoff (IFN-g > 0.35 IU/mL) resulted in 24.6% (95% uncertainty range, UR: 23.8–25.5) of the entire population testing false-positive over ten years. Raising the cutoff to >1.0 IU/mL or confirming initial positive results with a (presumed independent) second test reduced this false-positive percentage to 2.3% (95%UR: 2.0–2.6%) or 4.1% (95%UR: 3.7–4.5%), but also reduced the proportion of true incident infections detected within the first year of infection from 76.5% (95%UR: 66.3–84.6%) to 54.8% (95%UR: 44.6–64.5%) or 61.5% (95%UR: 51.6–70.9%), respectively. Serial QFT testing of HCWs in North America may result in tremendous over-diagnosis and over-treatment of LTBI, with nearly thirty false-positives for every true infection diagnosed. Using higher cutoffs for conversion or confirmatory tests (for initial positives) can mitigate these effects, but will also diagnose fewer true infections. PMID:27469388

The Hepatitis Testing and Linkage-to-Care Data Review Process: An Approach to Ensuring the Quality of Program Data.

PubMed

Mezzo, Jennifer L; Lamia, Tamara L; Danelski, Lisa L; Schipani, Anne Marie; Stokes, Scott A; Jacobs-Ware, Elizabeth D

2016-01-01

CDC's 2012 Hepatitis Testing and Linkage to Care (HepTLC) initiative was a nationally coordinated effort to conduct hepatitis B and hepatitis C screening, posttest counseling, and linkage to care at 34 U.S. sites. This project provided support for data management and monthly data reviews between awardees and a data manager, which facilitated monitoring of awardee progress and regular program improvement opportunities. CDC provided technical assistance to awardees for testing processes and program improvement, including Internet-based data submission, reporting software and data management to awardees, offering assistance with submitting, and reviewing data in real time. We describe how one awardee, AIDS Resource Center of Wisconsin (ARCW), used the data management process to improve data quality, inform testing processes and implementation, and measure and report missing variables from an online database. From October 2012 through July 2014, ARCW performed 2,255 HCV antibody (anti-HCV) tests and 244 HCV ribonucleic acid (RNA) tests as part of the HepTLC initiative. Participants who tested HCV RNA positive (n=189) were referred to medical care. At the end of the study, no records were missing for the anti-HCV test result or HCV RNA test result variables, and only one record was missing for those who were referred to medical care. Regular data review and monitoring by awardees and CDC-supported data managers provided opportunities for data quality and program improvement. Through regular data review, ARCW reduced the amount of missing data and promoted timely follow-up with participants testing positive for HCV to ensure receipt of results and linkage to care. Other programs can adopt a similar data management model.

Turnaround Time for Early Infant HIV Diagnosis in Rural Zambia: A Chart Review

PubMed Central

Sutcliffe, Catherine G.; van Dijk, Janneke H.; Hamangaba, Francis; Mayani, Felix; Moss, William J.

2014-01-01

Background Early infant HIV diagnosis is challenging in sub-Saharan Africa, particularly in rural areas where laboratory capacity is limited. Specimens must be transported to central laboratories for testing, leading to delays in diagnosis and initiation of antiretroviral therapy. This study was undertaken in rural Zambia to measure the turnaround time for confirmation of HIV infection and identify delays in diagnosis. Methods Chart reviews were conducted from 2010–2012 for children undergoing early infant HIV diagnosis at Macha Hospital in Zambia. Relevant dates, receipt of drugs by mother and child for the prevention of mother-to-child transmission (PMTCT), and test results were abstracted. Results 403 infants provided 476 samples for early infant diagnosis. The median age at the “6-week” and “6-month” assessments was 8.1 weeks and 7.0 months, respectively. The majority of mothers (80%) and infants (67%) received PMTCT. The median time between sample collection and arrival at the central laboratory in Lusaka was 17 days (IQR: 10, 28); arrival at the central laboratory to testing was 6 days (IQR: 5, 11); testing to return of results to the clinic was 29 days (IQR: 17, 36); arrival of results at the clinic to return of results to the caregiver was 45 days (IQR: 24, 79). The total median time from sample collection to return of results to the caregiver was 92 days (IQR: 84, 145). The proportion of HIV PCR positive samples was 12%. The total median turnaround time was shorter for HIV PCR positive as compared to negative or invalid samples (85 vs. 92 days; p = 0.08). Conclusions Delays in processing and communicating test results were identified, particularly in returning results from the central laboratory to the clinic and from the clinic to the caregiver. A more efficient process is needed so that caregivers can be provided test results more rapidly, potentially resulting in earlier treatment initiation and better outcomes for HIV-infected infants. PMID:24475214

10 CFR 26.97 - Conducting an initial test for alcohol using a specimen of oral fluids.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Conducting an initial test for alcohol using a specimen of oral fluids. 26.97 Section 26.97 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.97 Conducting an initial test for alcohol using a specimen of oral...

10 CFR 26.97 - Conducting an initial test for alcohol using a specimen of oral fluids.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Conducting an initial test for alcohol using a specimen of oral fluids. 26.97 Section 26.97 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.97 Conducting an initial test for alcohol using a specimen of oral...

10 CFR 26.97 - Conducting an initial test for alcohol using a specimen of oral fluids.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Conducting an initial test for alcohol using a specimen of oral fluids. 26.97 Section 26.97 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.97 Conducting an initial test for alcohol using a specimen of oral...

10 CFR 26.97 - Conducting an initial test for alcohol using a specimen of oral fluids.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Conducting an initial test for alcohol using a specimen of oral fluids. 26.97 Section 26.97 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.97 Conducting an initial test for alcohol using a specimen of oral...

10 CFR 26.97 - Conducting an initial test for alcohol using a specimen of oral fluids.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Conducting an initial test for alcohol using a specimen of oral fluids. 26.97 Section 26.97 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.97 Conducting an initial test for alcohol using a specimen of oral...

Analysis and testing of axial compression in imperfect slender truss struts

NASA Technical Reports Server (NTRS)

Lake, Mark S.; Georgiadis, Nicholas

1990-01-01

The axial compression of imperfect slender struts for large space structures is addressed. The load-shortening behavior of struts with initially imperfect shapes and eccentric compressive end loading is analyzed using linear beam-column theory and results are compared with geometrically nonlinear solutions to determine the applicability of linear analysis. A set of developmental aluminum clad graphite/epoxy struts sized for application to the Space Station Freedom truss are measured to determine their initial imperfection magnitude, load eccentricity, and cross sectional area and moment of inertia. Load-shortening curves are determined from axial compression tests of these specimens and are correlated with theoretical curves generated using linear analysis.

Technical Advisory Team (TAT) report on the rocket sled test accident of October 9, 2008.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stofleth, Jerome H.; Dinallo, Michael Anthony; Medina, Anthony J.

2009-01-01

This report summarizes probable causes and contributing factors that led to a rocket motor initiating prematurely while employees were preparing instrumentation for an AIII rocket sled test at SNL/NM, resulting in a Type-B Accident. Originally prepared by the Technical Advisory Team that provided technical assistance to the NNSA's Accident Investigation Board, the report includes analyses of several proposed causes and concludes that the most probable source of power for premature initiation of the rocket motor was the independent battery contained in the HiCap recorder package. The report includes data, evidence, and proposed scenarios to substantiate the analyses.

Correlation between Colon Transit Time Test Value and Initial Maintenance Dose of Laxative in Children with Chronic Functional Constipation

PubMed Central

Kim, Mock Ryeon; Park, Hye Won; Son, Jae Sung; Lee, Ran

2016-01-01

Purpose To evaluate the correlation between colon transit time (CTT) test value and initial maintenance dose of polyethylene glycol (PEG) 4000 or lactulose. Methods Of 415 children with chronic functional constipation, 190 were enrolled based on exclusion criteria using the CTT test, defecation diary, and clinical chart. The CTT test was performed with prior disimpaction. The laxative dose for maintenance was determined on the basis of the defecation diary and clinical chart. The Shapiro-Wilk test and Pearson's and Spearman's correlations were used for statistical analysis. Results The overall group median value and interquartile range of the CTT test was 43.8 (31.8) hours. The average PEG 4000 dose for maintenance in the overall group was 0.68±0.18 g/kg/d; according to age, the dose was 0.73±0.16 g/kg/d (<8 years), 0.53±0.12 g/kg/d (8 to <12 years), and 0.36±0.05 g/kg/d (12 to 15 years). The dose of lactulose was 1.99±0.43 mL/kg/d (<8 years) or 1.26±0.25 mL/kg/d (8 to <12 years). There was no significant correlation between CTT test value and initial dose of laxative, irrespective of the subgroup (encopresis, abnormal CTT test subtype) for either laxative. Even in the largest group (overall, n=109, younger than 8 years and on PEG 4000), the correlation was weak (Pearson's correlation coefficient [R]=0.268, p=0.005). Within the abnormal transit group, subgroup (n=73, younger than 8 years and on PEG 4000) correlation was weak (R=0.267, p=0.022). Conclusion CTT test value cannot predict the initial maintenance dose of PEG 4000 or lactulose with linear correlation. PMID:27738600

Comparison of Analytical Predictions and Experimental Results for a Dual Brayton Power System

NASA Technical Reports Server (NTRS)

Johnson, Paul

2007-01-01

NASA Glenn Research Center (GRC) contracted Barber- Nichols, Arvada, CO to construct a dual Brayton power conversion system for use as a hardware proof of concept and to validate results from a computational code known as the Closed Cycle System Simulation (CCSS). Initial checkout tests were performed at Barber- Nichols to ready the system for delivery to GRC. This presentation describes the system hardware components and lists the types of checkout tests performed along with a couple issues encountered while conducting the tests. A description of the CCSS model is also presented. The checkout tests did not focus on generating data, therefore, no test data or model analyses are presented.

Characterization of Mineralocorticoid Receptor Antagonist Therapy Initiation in High-Risk Patients With Heart Failure.

PubMed

Cooper, Lauren B; Hammill, Bradley G; Peterson, Eric D; Pitt, Bertram; Maciejewski, Matthew L; Curtis, Lesley H; Hernandez, Adrian F

2017-01-01

Heart failure guidelines recommend routine monitoring of serum potassium, and renal function in patients treated with a mineralocorticoid receptor antagonist (MRA). How these recommendations are implemented in high-risk patients or according to setting of drug initiation is poorly characterized. We conducted a retrospective cohort study of Medicare beneficiaries linked to laboratory data in 10 states with prevalent heart failure as of July 1, 2011, and incident MRA use between May 1 and September 30, 2011. Outcomes included laboratory testing before MRA initiation and in the early (days 1-10) and extended (days 11-90) post-initiation periods, based on setting of drug initiation and the presence of renal insufficiency. Additional outcomes included abnormal laboratory results and adverse events proximate to MRA initiation. Of 10 443 Medicare beneficiaries with heart failure started on an MRA, 19.7% were initiated during a hospitalization. Appropriate follow-up laboratory testing across all time periods occurred in 25.2% of patients with inpatient initiation compared with 2.8% of patients begun as an outpatient. Patients with chronic kidney disease had higher rates of both hyperkalemia and acute kidney failure in the early (1.3% and 2.7%, respectively) and extended (5.6% and 9.8%, respectively) post-initiation periods compared with those without chronic kidney disease. Patients initiated on MRA therapy as an outpatient had extremely poor rates of guideline indicated follow-up laboratory monitoring after drug initiation. In particular, patients with chronic kidney disease are at high risk for adverse events after MRA initiation. Quality improvement initiatives focused on systems to improve appropriate laboratory monitoring are needed. © 2017 American Heart Association, Inc.

SRNL SHELF LIFE STUDIES - SCC STUDIES AT ROOM TEMPERTURE [stress corrosion cracking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mickalonis, J.; Duffey, J.

Phase II, Series 2 corrosion testing performed by the Savannah River National Laboratory (SRNL) for the Department of Energy 3013 container has been completed. The corrosion tests are part of an integrated plan conducted jointly by Los Alamos National Laboratory and the Savannah River Site. SRNL was responsible for conducting corrosion studies in small-scale vessels to address the influence of salt composition, water loading, and type of oxide/salt contact on the relative humidity inside a 3013 container and on the resulting corrosion of Type 304L and 316L stainless steel (304L and 316L). This testing was conducted in two phases: Phasemore » I evaluated a broad spectrum of salt compositions and initial water loadings on the salt mixtures exposed to 304L and 316L and the resulting corrosion; Phase II evaluated the corrosion of 304L at specific water loadings and a single salt composition. During Phase I testing at high initial moisture levels (0.35 to 1.24 wt%)a, the roomtemperature corrosion of 304L exposed to a series of plutonium oxide/chloride salt mixtures ranged from superficial staining to pitting and stress corrosion cracking (SCC). 304L teardrop coupons that exhibited SCC were directly exposed to a mixture composed of 98 wt % PuO2, 0.9 wt % NaCl, 0.9 wt % KCl, and 0.2 wt % CaCl2. Cracking was not observed in a 316L teardrop coupon. Pitting was also observed in this environment for both 304L and 316L with depths ranging from 20 to 100 μm. Neither pitting nor SCC was observed in mixtures with a greater chloride salt concentration (5 and 28 wt%). These results demonstrated that for a corrosive solution to form a balance existed between the water loading and the salt chloride concentration. This chloride solution results from the interaction of loaded water with the hydrating CaCl2 salt. In Phase II, Series 1 tests, the SCC results were shown to be reproducible with cracking occurring in as little as 85 days. The approximate 0.5 wt% moisture level was found to result in an initial relative humidity of ~55% within the small-scale vessels. Pits were found to be associated with cracks and appeared to act as initiators for the cracking. In a vapor-space only exposure, the weld oxide, which results from the TIG closure weld used to fabricate the teardrop coupon, was also shown to be more susceptible to pitting corrosion than a surface free from weld oxide. This result has important implications for the closure weld of the 3013 inner can since the weld oxide on the can internal surface cannot be removed. The results from the Phase II, Series 2 tests further demonstrated the significance of forming a solution with a critical chloride concentration for corrosion to proceed. 304L teardrop coupons were found to corrode only by pitting with a similar oxide/salt mixture as used in Series 1 testing but with a lower water loading of 0.2 wt%, which resulted in an initial relative humidity of 35-38%. These tests ran twice as long as those for Series 1 testing. The exposure condition was also found to impact the corrosion with salt-exposed surfaces showing lower corrosion resistance. Additional analyses of the Series 2 coupons are recommended especially for determining if cracks emanate from the bottom of pits. Data generated under the 2009 3013 corrosion test plan, as was presented here, increased the understanding of the corrosion process within a sealed 3013 container. Along with the corrosion data from destructive evaluations of 3013 containers, the inner can closure weld region (ICCWR) has been identified as the most vulnerable area of the inner can where corrosion may lead to corrosive species leaking to the interior surface of the outer container, thereby jeopardizing the integrity of the 3013 container. A new corrosion plan has been designed that will characterize the corrosion at the ICCWR of 3013 DEs as well as parameters affecting this corrosion.« less

All of the above: When multiple correct response options enhance the testing effect.

PubMed

Bishara, Anthony J; Lanzo, Lauren A

2015-01-01

Previous research has shown that multiple choice tests often improve memory retention. However, the presence of incorrect lures often attenuates this memory benefit. The current research examined the effects of "all of the above" (AOTA) options. When such options are correct, no incorrect lures are present. In the first three experiments, a correct AOTA option on an initial test led to a larger memory benefit than no test and standard multiple choice test conditions. The benefits of a correct AOTA option occurred even without feedback on the initial test; for both 5-minute and 48-hour retention delays; and for both cued recall and multiple choice final test formats. In the final experiment, an AOTA question led to better memory retention than did a control condition that had identical timing and exposure to response options. However, the benefits relative to this control condition were similar regardless of the type of multiple choice test (AOTA or not). Results suggest that retrieval contributes to multiple choice testing effects. However, the extra testing effect from a correct AOTA option, rather than being due to more retrieval, might be due simply to more exposure to correct information.

Evaluation of the CDC proposed laboratory HIV testing algorithm among men who have sex with men (MSM) from five US metropolitan statistical areas using specimens collected in 2011.

PubMed

Masciotra, Silvina; Smith, Amanda J; Youngpairoj, Ae S; Sprinkle, Patrick; Miles, Isa; Sionean, Catlainn; Paz-Bailey, Gabriela; Johnson, Jeffrey A; Owen, S Michele

2013-12-01

Until recently most testing algorithms in the United States (US) utilized Western blot (WB) as the supplemental test. CDC has proposed an algorithm for HIV diagnosis which includes an initial screen with a Combo Antigen/Antibody 4th generation-immunoassay (IA), followed by an HIV-1/2 discriminatory IA of initially reactive-IA specimens. Discordant results in the proposed algorithm are resolved by nucleic acid-amplification testing (NAAT). Evaluate the results obtained with the CDC proposed laboratory-based algorithm using specimens from men who have sex with men (MSM) obtained in five metropolitan statistical areas (MSAs). Specimens from 992 MSM from five MSAs participating in the CDC's National HIV Behavioral Surveillance System in 2011 were tested at local facilities and CDC. The five MSAs utilized algorithms of various screening assays and specimen types, and WB as the supplemental test. At the CDC, serum/plasma specimens were screened with 4th generation-IA and the Multispot HIV-1/HIV-2 discriminatory assay was used as the supplemental test. NAAT was used to resolve discordant results and to further identify acute HIV infections from all screened-non-reactive missed by the proposed algorithm. Performance of the proposed algorithm was compared to site-specific WB-based algorithms. The proposed algorithm detected 254 infections. The WB-based algorithms detected 19 fewer infections; 4 by oral fluid (OF) rapid testing and 15 by WB supplemental testing (12 OF and 3 blood). One acute infection was identified by NAAT from all screened-non-reactive specimens. The proposed algorithm identified more infections than the WB-based algorithms in a high-risk MSM population. OF testing was associated with most of the discordant results between algorithms. HIV testing with the proposed algorithm can increase diagnosis of infected individuals, including early infections. Published by Elsevier B.V.