10 CFR 26.91 - Acceptable devices for conducting initial and confirmatory tests for alcohol and methods of use.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Acceptable devices for conducting initial and confirmatory tests for alcohol and methods of use. 26.91 Section 26.91 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.91 Acceptable devices for conducting initial...

40 CFR 63.2261 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2014 CFR

2014-07-01

... conduct performance tests upon initial startup or no later than 180 calendar days after the compliance... initial startup or no later than 30 calendar days after the compliance date that is specified for your...

40 CFR 63.2261 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2012 CFR

2012-07-01

... conduct performance tests upon initial startup or no later than 180 calendar days after the compliance... initial startup or no later than 30 calendar days after the compliance date that is specified for your...

40 CFR 60.2922 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2014 CFR

2014-07-01

... of this part must be used. (ii) The post-test moisture removal procedure described in section 8.1.6... performance test? 60.2922 Section 60.2922 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Testing § 60.2922 How do I conduct the initial and annual performance test? (a) All performance tests must...

40 CFR 60.2922 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2013 CFR

2013-07-01

... of this part must be used. (ii) The post-test moisture removal procedure described in section 8.1.6... performance test? 60.2922 Section 60.2922 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Testing § 60.2922 How do I conduct the initial and annual performance test? (a) All performance tests must...

40 CFR 60.3027 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 26A of appendix A of this part must be used. (ii) The post-test moisture removal procedure described... performance test? 60.3027 Section 60.3027 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED..., 2004 Model Rule-Performance Testing § 60.3027 How do I conduct the initial and annual performance test...

40 CFR 60.2922 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 26A of appendix A of this part must be used. (ii) The post-test moisture removal procedure described... performance test? 60.2922 Section 60.2922 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Qualification Performance Testing § 60.2922 How do I conduct the initial and annual performance test? (a) All...

40 CFR 60.3027 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 26A of appendix A of this part must be used. (ii) The post-test moisture removal procedure described... performance test? 60.3027 Section 60.3027 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED..., 2004 Model Rule-Performance Testing § 60.3027 How do I conduct the initial and annual performance test...

40 CFR 60.3027 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 26A of appendix A of this part must be used. (ii) The post-test moisture removal procedure described... performance test? 60.3027 Section 60.3027 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED..., 2004 Model Rule-Performance Testing § 60.3027 How do I conduct the initial and annual performance test...

40 CFR 60.3027 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 26A of appendix A of this part must be used. (ii) The post-test moisture removal procedure described... performance test? 60.3027 Section 60.3027 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED..., 2004 Model Rule-Performance Testing § 60.3027 How do I conduct the initial and annual performance test...

40 CFR 60.3027 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 26A of appendix A of this part must be used. (ii) The post-test moisture removal procedure described... performance test? 60.3027 Section 60.3027 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED..., 2004 Model Rule-Performance Testing § 60.3027 How do I conduct the initial and annual performance test...

40 CFR 60.2922 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 26A of appendix A of this part must be used. (ii) The post-test moisture removal procedure described... performance test? 60.2922 Section 60.2922 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Qualification Performance Testing § 60.2922 How do I conduct the initial and annual performance test? (a) All...

40 CFR 60.2922 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 26A of appendix A of this part must be used. (ii) The post-test moisture removal procedure described... performance test? 60.2922 Section 60.2922 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Qualification Performance Testing § 60.2922 How do I conduct the initial and annual performance test? (a) All...

40 CFR 63.6610 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2010 CFR

2010-07-01

... initial performance tests or other initial compliance demonstrations if I own or operate a stationary RICE... performance tests or other initial compliance demonstrations if I own or operate a stationary RICE with a site... stationary RICE with a site rating of more than 500 brake HP located at a major source of HAP emissions you...

40 CFR 63.6610 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2011 CFR

2011-07-01

... initial performance tests or other initial compliance demonstrations if I own or operate a stationary RICE... performance tests or other initial compliance demonstrations if I own or operate a stationary RICE with a site... stationary RICE with a site rating of more than 500 brake HP located at a major source of HAP emissions you...

40 CFR 62.15230 - What types of stack tests must I conduct?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false What types of stack tests must I... August 30, 1999 Stack Testing § 62.15230 What types of stack tests must I conduct? Conduct initial and... matter, opacity, hydrogen chloride, and fugitive ash. ...

40 CFR 62.15230 - What types of stack tests must I conduct?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 8 2011-07-01 2011-07-01 false What types of stack tests must I... August 30, 1999 Stack Testing § 62.15230 What types of stack tests must I conduct? Conduct initial and... matter, opacity, hydrogen chloride, and fugitive ash. ...

40 CFR 63.7940 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... compliance is not demonstrated using a performance test or design evaluation, you must demonstrate initial... performance tests or other initial compliance demonstrations? 63.7940 Section 63.7940 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS...

40 CFR 60.1775 - What types of stack tests must I conduct?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false What types of stack tests must I...-Stack Testing § 60.1775 What types of stack tests must I conduct? Conduct initial and annual stack tests to measure the emission levels of dioxins/furans, cadmium, lead, mercury, particulate matter, opacity...

40 CFR 60.1775 - What types of stack tests must I conduct?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What types of stack tests must I...-Stack Testing § 60.1775 What types of stack tests must I conduct? Conduct initial and annual stack tests to measure the emission levels of dioxins/furans, cadmium, lead, mercury, particulate matter, opacity...

40 CFR 63.6615 - When must I conduct subsequent performance tests?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 13 2010-07-01 2010-07-01 false When must I conduct subsequent performance tests? 63.6615 Section 63.6615 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Internal Combustion Engines Testing and Initial Compliance Requirements § 63.6615 When must I conduct...

40 CFR 63.2261 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... initial startup or no later than 180 calendar days after the compliance date that is specified for your... compliance demonstrations that do not require performance tests upon initial startup or no later than 30...

40 CFR 63.2261 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... initial startup or no later than 180 calendar days after the compliance date that is specified for your... compliance demonstrations that do not require performance tests upon initial startup or no later than 30...

40 CFR 63.7941 - How do I conduct a performance test, design evaluation, or other type of initial compliance...

Code of Federal Regulations, 2014 CFR

2014-07-01

... of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION... Hazardous Air Pollutants: Site Remediation Performance Tests § 63.7941 How do I conduct a performance test...

40 CFR 63.7940 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2012 CFR

2012-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS... Pollutants: Site Remediation Performance Tests § 63.7940 By what date must I conduct performance tests or...

40 CFR 63.5992 - When must I conduct subsequent performance tests?

Code of Federal Regulations, 2010 CFR

2010-07-01

... performance tests? 63.5992 Section 63.5992 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... CATEGORIES National Emissions Standards for Hazardous Air Pollutants: Rubber Tire Manufacturing General Testing and Initial Compliance Requirements § 63.5992 When must I conduct subsequent performance tests? If...

40 CFR 63.5845 - When must I conduct subsequent performance tests?

Code of Federal Regulations, 2010 CFR

2010-07-01

... CATEGORIES National Emissions Standards for Hazardous Air Pollutants: Reinforced Plastic Composites Production Testing and Initial Compliance Requirements § 63.5845 When must I conduct subsequent performance...

Ground vibration test of F-16 airplane with initial decoupler pylon

NASA Technical Reports Server (NTRS)

Cazier, F. W., Jr.; Kehoe, M. W.

1984-01-01

A ground vibration test was conducted on an F-16 airplane loaded on each wing with a 370-gal tank mounted on a standard pylon, a GBU-8 store mounted on a decoupler pylon, and an AIM-9J missile mounted on a wing-tip launcher. The decoupler pylon is a passive wing/store flutter-suppression device. The test was conducted prior to initial flight tests to determine the modal frequencies, mode shapes, and structural damping coefficients. The data presented include frequency response plots, force effect plots, and limited mode shape data.

78 FR 46996 - Current List of Laboratories and Instrumented Initial Testing Facilities Which Meet Minimum...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-02

... Engage in Urine Drug Testing for Federal Agencies AGENCY: Substance Abuse and Mental Health Services... the standards of the Mandatory Guidelines for Federal Workplace Drug Testing Programs (Mandatory... and Instrumented Initial Testing Facilities (IITF) must meet in order to conduct drug and specimen...

49 CFR 40.91 - What validity tests must laboratories conduct on primary specimens?

Code of Federal Regulations, 2011 CFR

2011-10-01

... FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.91 What... testing under § 40.89, you must conduct it in accordance with the requirements of this section. (a) You... responses characteristic of an adulterant obtained during initial or confirmatory drug tests (e.g., non...

49 CFR 40.91 - What validity tests must laboratories conduct on primary specimens?

Code of Federal Regulations, 2012 CFR

2012-10-01

... FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.91 What... testing under § 40.89, you must conduct it in accordance with the requirements of this section. (a) You... responses characteristic of an adulterant obtained during initial or confirmatory drug tests (e.g., non...

49 CFR 40.91 - What validity tests must laboratories conduct on primary specimens?

Code of Federal Regulations, 2010 CFR

2010-10-01

... FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.91 What... testing under § 40.89, you must conduct it in accordance with the requirements of this section. (a) You... responses characteristic of an adulterant obtained during initial or confirmatory drug tests (e.g., non...

49 CFR 40.91 - What validity tests must laboratories conduct on primary specimens?

Code of Federal Regulations, 2014 CFR

2014-10-01

... FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.91 What... testing under § 40.89, you must conduct it in accordance with the requirements of this section. (a) You... responses characteristic of an adulterant obtained during initial or confirmatory drug tests (e.g., non...

49 CFR 40.91 - What validity tests must laboratories conduct on primary specimens?

Code of Federal Regulations, 2013 CFR

2013-10-01

... FOR TRANSPORTATION WORKPLACE DRUG AND ALCOHOL TESTING PROGRAMS Drug Testing Laboratories § 40.91 What... testing under § 40.89, you must conduct it in accordance with the requirements of this section. (a) You... responses characteristic of an adulterant obtained during initial or confirmatory drug tests (e.g., non...

Investigation of Low-Cycle Bending Fatigue of AISI 9310 Steel Spur Gears

NASA Technical Reports Server (NTRS)

Handschuh, Robert F.; Krantz, Timothy L.; Lerch, Bradley A.; Burke, Christopher S.

2007-01-01

An investigation of the low-cycle bending fatigue of spur gears made from AISI 9310 gear steel was completed. Tests were conducted using the single-tooth bending method to achieve crack initiation and propagation. Tests were conducted on spur gears in a fatigue test machine using a dedicated gear test fixture. Test loads were applied at the highest point of single tooth contact. Gear bending stresses for a given testing load were calculated using a linear-elastic finite element model. Test data were accumulated from 1/4 cycle to several thousand cycles depending on the test stress level. The relationship of stress and cycles for crack initiation was found to be semi-logarithmic. The relationship of stress and cycles for crack propagation was found to be linear. For the range of loads investigated, the crack propagation phase is related to the level of load being applied. Very high loads have comparable crack initiation and propagation times whereas lower loads can have a much smaller number of cycles for crack propagation cycles as compared to crack initiation.

Investigation of Low-Cycle Bending Fatigue of AISI 9310 Steel Spur Gears

NASA Technical Reports Server (NTRS)

Handschuh, Robert F.; Krantz, Timothy L.; Lerch, Bradley A.; Burke, Christopher S.

2007-01-01

An investigation of the low-cycle bending fatigue of spur gears made from AISI 9310 gear steel was completed. Tests were conducted using the single-tooth bending method to achieve crack initiation and propagation. Tests were conducted on spur gears in a fatigue test machine using a dedicated gear test fixture. Test loads were applied at the highest point of single tooth contact. Gear bending stresses for a given testing load were calculated using a linear-elastic finite element model. Test data were accumulated from 1/4 cycle to several thousand cycles depending on the test stress level. The relationship of stress and cycles for crack initiation was found to be semilogarithmic. The relationship of stress and cycles for crack propagation was found to be linear. For the range of loads investigated, the crack propagation phase is related to the level of load being applied. Very high loads have comparable crack initiation and propagation times whereas lower loads can have a much smaller number of cycles for crack propagation cycles as compared to crack initiation.

40 CFR 63.5991 - By what date must I conduct an initial compliance demonstration or performance test?

Code of Federal Regulations, 2010 CFR

2010-07-01

... compliance demonstration or performance test? 63.5991 Section 63.5991 Protection of Environment ENVIRONMENTAL... POLLUTANTS FOR SOURCE CATEGORIES National Emissions Standards for Hazardous Air Pollutants: Rubber Tire... initial compliance demonstration or performance test? (a) If you have a new or reconstructed affected...

40 CFR 63.7321 - When must I conduct subsequent performance tests?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 13 2010-07-01 2010-07-01 false When must I conduct subsequent performance tests? 63.7321 Section 63.7321 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY..., Quenching, and Battery Stacks Initial Compliance Requirements § 63.7321 When must I conduct subsequent...

Effects of Aggregation on Blood Sedimentation and Conductivity

PubMed Central

Zhbanov, Alexander; Yang, Sung

2015-01-01

The erythrocyte sedimentation rate (ESR) test has been used for over a century. The Westergren method is routinely used in a variety of clinics. However, the mechanism of erythrocyte sedimentation remains unclear, and the 60 min required for the test seems excessive. We investigated the effects of cell aggregation during blood sedimentation and electrical conductivity at different hematocrits. A sample of blood was drop cast into a small chamber with two planar electrodes placed on the bottom. The measured blood conductivity increased slightly during the first minute and decreased thereafter. We explored various methods of enhancing or retarding the erythrocyte aggregation. Using experimental measurements and theoretical calculations, we show that the initial increase in blood conductivity was indeed caused by aggregation, while the subsequent decrease in conductivity resulted from the deposition of erythrocytes. We present a method for calculating blood conductivity based on effective medium theory. Erythrocytes are modeled as conducting spheroids surrounded by a thin insulating membrane. A digital camera was used to investigate the erythrocyte sedimentation behavior and the distribution of the cell volume fraction in a capillary tube. Experimental observations and theoretical estimations of the settling velocity are provided. We experimentally demonstrate that the disaggregated cells settle much slower than the aggregated cells. We show that our method of measuring the electrical conductivity credibly reflected the ESR. The method was very sensitive to the initial stage of aggregation and sedimentation, while the sedimentation curve for the Westergren ESR test has a very mild slope in the initial time. We tested our method for rapid estimation of the Westergren ESR. We show a correlation between our method of measuring changes in blood conductivity and standard Westergren ESR method. In the future, our method could be examined as a potential means of accelerating ESR tests in clinical practice. PMID:26047511

40 CFR 63.7940 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS... Hazardous Air Pollutants: Site Remediation Performance Tests § 63.7940 By what date must I conduct...

40 CFR 63.7940 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS... Hazardous Air Pollutants: Site Remediation Performance Tests § 63.7940 By what date must I conduct...

40 CFR 63.7940 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS... Hazardous Air Pollutants: Site Remediation Performance Tests § 63.7940 By what date must I conduct...

40 CFR 63.7822 - What test methods and other procedures must I use to demonstrate initial compliance with the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... must I use to demonstrate initial compliance with the emission limits for particulate matter? 63.7822... demonstrate initial compliance with the emission limits for particulate matter? (a) You must conduct each... applicable emission limit for particulate matter in Table 1 to this subpart, follow the test methods and...

40 CFR 63.7822 - What test methods and other procedures must I use to demonstrate initial compliance with the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... must I use to demonstrate initial compliance with the emission limits for particulate matter? 63.7822... demonstrate initial compliance with the emission limits for particulate matter? (a) You must conduct each... applicable emission limit for particulate matter in Table 1 to this subpart, follow the test methods and...

Initial Teacher Licensure Testing in Tennessee: Test Validation.

ERIC Educational Resources Information Center

Bowman, Harry L.; Petry, John R.

In 1988 a study was conducted to determine the validity of candidate teacher licensure examinations for use in Tennessee under the 1984 Comprehensive Education Reform Act. The Department of Education conducted a study to determine the validity of 11 previously unvalidated or extensively revised tests for certification and to make recommendations…

"It Is Not Easy": Challenges for Provider-Initiated HIV Testing and Counseling in Flanders, Belgium

ERIC Educational Resources Information Center

Manirankunda, Lazare; Loos, Jasna; Debackaere, Pieterjan; Nostlinger, Christiana

2012-01-01

This study identified physicians' HIV testing practices and their barriers toward implementing provider-initiated HIV testing and counseling (PITC) for Sub-Saharan African migrants (SAM) in Flanders, Belgium. In-depth interviews were conducted on a purposive sample of 20 physicians (ten GPs and ten internists). GPs performed mainly…

40 CFR 63.7515 - When must I conduct subsequent performance tests, fuel analyses, or tune-ups?

Code of Federal Regulations, 2011 CFR

2011-07-01

... performance tests, fuel analyses, or tune-ups? 63.7515 Section 63.7515 Protection of Environment ENVIRONMENTAL... Compliance Requirements § 63.7515 When must I conduct subsequent performance tests, fuel analyses, or tune... and the associated initial fuel analyses within 90 days after the completion of the performance tests...

40 CFR 63.7515 - When must I conduct subsequent performance tests, fuel analyses, or tune-ups?

Code of Federal Regulations, 2012 CFR

2012-07-01

... performance tests, fuel analyses, or tune-ups? 63.7515 Section 63.7515 Protection of Environment ENVIRONMENTAL... Compliance Requirements § 63.7515 When must I conduct subsequent performance tests, fuel analyses, or tune... and the associated initial fuel analyses within 90 days after the completion of the performance tests...

40 CFR 63.3960 - By what date must I conduct performance tests and other initial compliance demonstrations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... performance test of one representative magnet wire coating machine for each group of identical or very similar... you complete the performance test of a representative magnet wire coating machine. The requirements in... operations, you may, with approval, conduct a performance test of a single magnet wire coating machine that...

Integrated corridor management initiative : demonstration phase evaluation – Dallas corridor performance analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Corridor Performance Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM ...

Integrated corridor management initiative : demonstration phase evaluation – San Diego corridor performance analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Corridor Performance Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM proje...

Integrated corridor management initiative : demonstration phase evaluation - Dallas decision support system analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Decision Support System (DSS) Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration....

Integrated corridor management initiative : demonstration phase evaluation – Dallas technical capability analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Technical Capability Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM ...

49 CFR 232.205 - Class I brake test-initial terminal inspection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... § 232.205 Class I brake test-initial terminal inspection. (a) Each train and each car in the train shall... tested solid block of cars to the train; (iii) Changing motive power; (iv) Removing or changing the... conduct a brake test pursuant to § 232.209 on those cars added to the train. (B) [Reserved] (b) Except as...

Integrated corridor management initiative : demonstration phase evaluation – San Diego benefit-cost analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Benefit-Cost Analysis (BCA) for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM project...

Development and Testing of a USM High Altitude Balloon

NASA Astrophysics Data System (ADS)

Thaheer, A. S. Mohamed; Ismail, N. A.; Yusoff, S. H. Md.; Nasirudin, M. A.

2018-04-01

This paper discusses on tests conducted on the component and subsystem level during development of the USM High Altitude Balloon (HAB). The tests conducted by selecting initial components then tested individually based on several case studies such as reliability test, camera viewing, power consumption, thermal capability, and parachute performance. Then, the component is integrated into sub-system level for integration and functionality test. The preliminary result is utilized to tune the components and sub-systems and trial launch is conducted where the sample images are recorded and atmospheric data successfully collected.

Laser diode ignition characteristics of Zirconium Potassium Perchlorate (ZPP)

NASA Technical Reports Server (NTRS)

Callaghan, Jerry D.; Tindol, Scot

1993-01-01

Hi-Shear Technology, Corp., (HSTC) has designed and built a Laser equivalent NASA Standard Initiator (LNSI). Langlie tests with a laser diode output initiating ZPP were conducted as a part of this effort. The test parameters include time to first pressure, laser power density requirements, and ignition time. The data from these laser tests on ZPP are presented.

Effects of thickness on the aerodynamic characteristics of an initial low-speed family of airfoils for general aviation applications

NASA Technical Reports Server (NTRS)

Mcghee, R. J.; Beasley, W. D.

1976-01-01

Wind tunnel tests were conducted to determine the effects of airfoil thickness-ratio on the low speed aerodynamic characteristics of an initial family of airfoils. The results were compared with theoretical predictions obtained from a subsonic viscous method. The tests were conducted over a Mach number range from 0.10 to 0.28. Chord Reynolds numbers varied from about 2.0 x 1 million to 9.0 x 1 million.

Shakedown Tests for Refurbished and Upgraded Frames and Initiation of Alloy 709 Creep Rupture Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Hong; Moser, Jeremy L.; Hawkins, Charles S.

This report describes the shakedown tests conducted on the upgraded frames, and initiation of creep rupture tests on refurbished frames. SS316H, a reference material for Alloy 709, was used in shakedown tests, and the tests were conducted at 816 degree C under three stress levels to accumulate 1% creep strain. 1/4” gage diameter specimen design was used. The creep rupture tests on Alloy 709 were initiated at 600 degree C under 330 MPa to target 1,500 h rupture time. 12 specimens with 3/8” gage diameter were prepared from the materials with 6 heat treatment conditions, 2 from each. The requiredmore » mechanical load under 330MPa was calculated to be 5,286 lb for the 3/8” gage diameter specimen. Among the ART frames, 7 frames are equipped with 10,000 lb load cell including #5 to 8 and #88 to 90, and can be used. 7 tests were thus started in this stage of project, and remaining 5 will be continued whenever any of the 7 tests is completed.« less

40 CFR 63.7110 - By what date must I conduct performance tests and other initial compliance demonstrations?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Lime Manufacturing Plants Testing and Initial Compliance Requirements § 63.7110...

40 CFR 63.7110 - By what date must I conduct performance tests and other initial compliance demonstrations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Lime Manufacturing Plants Testing and Initial Compliance Requirements § 63.7110...

40 CFR 63.7110 - By what date must I conduct performance tests and other initial compliance demonstrations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Lime Manufacturing Plants Testing and Initial Compliance Requirements § 63.7110...

40 CFR 63.7820 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... sinter plant feedstock in § 63.7790(d)(1) or alternative limit for volatile organic compound emissions from the sinter plant windbox exhaust stream in § 63.7790(d)(2). You must conduct the performance tests...

40 CFR 63.7820 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2012 CFR

2012-07-01

... sinter plant feedstock in § 63.7790(d)(1) or alternative limit for volatile organic compound emissions from the sinter plant windbox exhaust stream in § 63.7790(d)(2). You must conduct the performance tests...

40 CFR 63.7820 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2014 CFR

2014-07-01

... sinter plant feedstock in § 63.7790(d)(1) or alternative limit for volatile organic compound emissions from the sinter plant windbox exhaust stream in § 63.7790(d)(2). You must conduct the performance tests...

40 CFR 63.7820 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... sinter plant feedstock in § 63.7790(d)(1) or alternative limit for volatile organic compound emissions from the sinter plant windbox exhaust stream in § 63.7790(d)(2). You must conduct the performance tests...

Initial Evaluation of Acoustic Emission SHM of PRSEUS Multi-bay Box Tests

NASA Technical Reports Server (NTRS)

Horne, Michael R.; Madaras, Eric I.

2016-01-01

A series of tests of the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) HWB Multi-Bay Test Article were conducted during the second quarter of 2015 at NASA Langley Research Center (LaRC) in the Combined Loads Test facility (COLTS). This report documents the Acoustic Emission (AE) data collected during those tests along with an initial analysis of the data. A more detailed analysis will be presented in future publications.

Small crack test program for helicopter materials

NASA Technical Reports Server (NTRS)

Annigeri, Bal; Schneider, George

1994-01-01

Crack propagation tests were conducted to determine crack growth behavior in five helicopter materials for surface cracks between 0.005 to 0.020 inches in depth. Constant amplitude tests were conducted at stress ratios R equals 0.1 and 0.5, and emphasis was placed on near threshold data (i.e., 10-8 to 10-6 inches/cycle). Spectrum tests were conducted using a helicopter spectrum. The test specimen was an unnotched tension specimen, and cracks were initiated from a small EDM notch. An optical/video system was used to monitor crack growth. The material for the test specimens was obtained from helicopter part forgings. Testing was conducted at stresses below yield to reflect actual stresses in helicopter parts.

40 CFR 63.7110 - By what date must I conduct performance tests and other initial compliance demonstrations?

Code of Federal Regulations, 2012 CFR

2012-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Lime Manufacturing Plants Testing and Initial Compliance Requirements § 63.7110 By what date...

Thermal Conductivity and Elastic Modulus Evolution of Thermal Barrier Coatings under High Heat Flux Conditions

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Miller, Robert A.

1999-01-01

Laser high heat flux test approaches have been established to obtain critical properties of ceramic thermal barrier coatings (TBCs) under near-realistic temperature and thermal gradients that may he encountered in advanced engine systems. Thermal conductivity change kinetics of a thin ceramic coating were continuously monitored in real time at various test temperatures. A significant thermal conductivity increase was observed during the laser simulated engine heat flux tests. For a 0.25 mm thick ZrO2-8%Y2O3 coating system, the overall thermal conductivity increased from the initial value of 1.0 W/m-K to 1. 15 W/m-K, 1. 19 W/m-K and 1.5 W/m-K after 30 hour testing at surface temperatures of 990C, 1100C, and 1320C. respectively. Hardness and modulus gradients across a 1.5 mm thick TBC system were also determined as a function of laser testing time using the laser sintering/creep and micro-indentation techniques. The coating Knoop hardness values increased from the initial hardness value of 4 GPa to 5 GPa near the ceramic/bond coat interface, and to 7.5 GPa at the ceramic coating surface after 120 hour testing. The ceramic surface modulus increased from an initial value of about 70 GPa to a final value of 125 GPa. The increase in thermal conductivity and the evolution of significant hardness and modulus gradients in the TBC systems are attributed to sintering-induced micro-porosity gradients under the laser-imposed high thermal gradient conditions. The test techniques provide a viable means for obtaining coating data for use in design, development, stress modeling, and life prediction for various thermal barrier coating applications.

Ground vibration test of the laminar flow control JStar airplane

NASA Technical Reports Server (NTRS)

Kehoe, M. W.; Cazier, F. W., Jr.; Ellison, J. F.

1985-01-01

A ground vibration test was conducted on a Lockheed JetStar airplane that had been modified for the purpose of conducting laminar flow control experiments. The test was performed prior to initial flight flutter tests. Both sine-dwell and single-point-random excitation methods were used. The data presented include frequency response functions and a comparison of mode frequencies and mode shapes from both methods.

A small punch test technique for characterizing the elastic modulus and fracture behavior of PMMA bone cement used in total joint replacement.

PubMed

Giddings, V L; Kurtz, S M; Jewett, C W; Foulds, J R; Edidin, A A

2001-07-01

Polymethylmethacrylate (PMMA) bone cement is used in total joint replacements to anchor implants to the underlying bone. Establishing and maintaining the integrity of bone cement is thus of critical importance to the long-term outcome of joint replacement surgery. The goal of the present study was to evaluate the suitability of a novel testing technique, the small punch or miniaturized disk bend test, to characterize the elastic modulus and fracture behavior of PMMA. We investigated the hypothesis that the crack initiation behavior of PMMA during the small punch test was sensitive to the test temperature. Miniature disk-shaped specimens, 0.5 mm thick and 6.4 mm in diameter, were prepared from PMMA and Simplex-P bone cement according to manufacturers' instructions. Testing was conducted at ambient and body temperatures, and the effect of test temperature on the elastic modulus and fracture behavior was statistically evaluated using analysis of variance. For both PMMA materials, the test temperature had a significant effect on elastic modulus and crack initiation behavior. At body temperature, the specimens exhibited "ductile" crack initiation, whereas at room temperature "brittle" crack initiation was observed. The small punch test was found to be a sensitive and repeatable test method for evaluating the mechanical behavior of PMMA. In light of the results of this study, future small punch testing should be conducted at body temperature.

Isolator fragmentation and explosive initiation tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dickson, Peter; Rae, Philip John; Foley, Timothy J.

2016-09-19

Three tests were conducted to evaluate the effects of firing an isolator in proximity to a barrier or explosive charge. The tests with explosive were conducted without a barrier, on the basis that since any barrier will reduce the shock transmitted to the explosive, bare explosive represents the worst-case from an inadvertent initiation perspective. No reaction was observed. The shock caused by the impact of a representative plastic material on both bare and cased PBX 9501 is calculated in the worst-case, 1-D limit, and the known shock response of the HE is used to estimate minimum run-to-detonation lengths. The estimatesmore » demonstrate that even 1-D impacts would not be of concern and that, accordingly, the divergent shocks due to isolator fragment impact are of no concern as initiating stimuli.« less

Isolator fragmentation and explosive initiation tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dickson, Peter; Rae, Philip John; Foley, Timothy J.

2015-09-30

Three tests were conducted to evaluate the effects of firing an isolator in proximity to a barrier or explosive charge. The tests with explosive were conducted without barrier, on the basis that since any barrier will reduce the shock transmitted to the explosive, bare explosive represents the worst-case from an inadvertent initiation perspective. No reaction was observed. The shock caused by the impact of a representative plastic material on both bare and cased PBX9501 is calculated in the worst-case, 1-D limit, and the known shock response of the HE is used to estimate minimum run-to-detonation lengths. The estimates demonstrate thatmore » even 1-D impacts would not be of concern and that, accordingly, the divergent shocks due to isolator fragment impact are of no concern as initiating stimuli.« less

Improving Beta Test Evaluation Response Rates: A Meta-Evaluation

ERIC Educational Resources Information Center

Russ-Eft, Darlene; Preskill, Hallie

2005-01-01

This study presents a meta-evaluation of a beta-test of a customer service training program. The initial evaluation showed a low response rate. Therefore, the meta-evaluation focused on issues related to the conduct of the initial evaluation and reasons for nonresponse. The meta-evaluation identified solutions to the nonresponse problem as related…

Compilation, design tests: Energetic particles Satellite S-3 including design tests for S-3A, S-3B and S-3C

NASA Technical Reports Server (NTRS)

Ledoux, F. N.

1973-01-01

A compilation of engineering design tests which were conducted in support of the Energetic Particle Satellite S-3, S-3A, and S-3b programs. The purpose for conducting the tests was to determine the adequacy and reliability of the Energetic Particles Series of satellites designs. The various tests consisted of: (1) moments of inertia, (2) functional reliability, (3) component and structural integrity, (4) initiators and explosives tests, and (5) acceptance tests.

Barriers to and acceptability of provider-initiated HIV testing and counselling and adopting HIV-prevention behaviours in rural Uganda: a qualitative study.

PubMed

Kiene, Susan M; Sileo, Katelyn; Wanyenze, Rhoda K; Lule, Haruna; Bateganya, Moses H; Jasperse, Joseph; Nantaba, Harriet; Jayaratne, Kia

2015-02-01

In Uganda, a nationwide scale-up of provider-initiated HIV testing and counselling presents an opportunity to deliver HIV-prevention services to large numbers of people. In a rural Ugandan hospital, focus group discussions and key informant interviews were conducted with outpatients receiving provider-initiated HIV testing and counselling and staff to explore the HIV-prevention information, motivation and behavioural skills strengths and weaknesses, and community-level and structural barriers to provider-initiated HIV testing and counselling acceptability and HIV prevention among this population. Strengths and weakness occurred at all levels, and results suggest brief client-centred interventions during provider-initiated HIV testing and counselling may be an effective approach to increase prevention behaviours in outpatient settings. © The Author(s) 2013.

40 CFR 60.2705 - By what date must I conduct the initial performance test?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Initial Compliance...

40 CFR 60.2705 - By what date must I conduct the initial performance test?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Initial Compliance...

Development and Evaluation of a Prototype Wheeled Ultra-High Pressure Extinguisher System with Novec 1230

DTIC Science & Technology

2016-01-01

Fire Tests Pool fire tests were conducted as outlined below, and consisted of a pretest phase, in which the F-100 engine nacelle was first...the nacelle during the test phase. Pretest Phase  Determine and record extinguisher full weight.  Initiate flow of jet fuel through the...extinguisher after test. 3.4.2. Rear Engine Fire Tests Rear engine fire tests were conducted as outlined below, and consisted of a pretest phase

40 CFR 63.9621 - What test methods and other procedures must I use to demonstrate initial compliance with the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... must I use to demonstrate initial compliance with the emission limits for particulate matter? 63.9621... the emission limits for particulate matter? (a) You must conduct each performance test that applies to... source, you must determine compliance with the applicable emission limit for particulate matter in Table...

40 CFR 63.9621 - What test methods and other procedures must I use to demonstrate initial compliance with the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... must I use to demonstrate initial compliance with the emission limits for particulate matter? 63.9621... the emission limits for particulate matter? (a) You must conduct each performance test that applies to... source, you must determine compliance with the applicable emission limit for particulate matter in Table...

Electronic freight management (EFM) standards strategy

DOT National Transportation Integrated Search

2006-04-01

The EFM initiative is a U.S. Department of Transportation (DOT)-sponsored research effort aimed at improving the operating efficiency, safety, and security of freight movement. The initiative involves conducting a deployment test using Web services t...

40 CFR 63.11960 - What are my initial and continuous compliance requirements for stripped resin?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Demonstration of initial compliance. You must demonstrate initial compliance for each resin stripper or for each group of resin strippers used to process the same resin type. (1) You must conduct an initial performance test for the resin stripper, measuring the concentration of vinyl chloride and total non-vinyl...

40 CFR 63.11960 - What are my initial and continuous compliance requirements for stripped resin?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Demonstration of initial compliance. You must demonstrate initial compliance for each resin stripper or for each group of resin strippers used to process the same resin type. (1) You must conduct an initial performance test for the resin stripper, measuring the concentration of vinyl chloride and total non-vinyl...

40 CFR 63.11960 - What are my initial and continuous compliance requirements for stripped resin?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Demonstration of initial compliance. You must demonstrate initial compliance for each resin stripper or for each group of resin strippers used to process the same resin type. (1) You must conduct an initial performance test for the resin stripper, measuring the concentration of vinyl chloride and total non-vinyl...

Flight service evaluation of composite helicopter components

NASA Technical Reports Server (NTRS)

Rich, M. J.; Lowry, D. W.

1983-01-01

This first interim report presents the technical background for including environmental effects in the design of helicopter composite structures, and test results after approximately two year field exposure of components and panels. Composite structural components were removed from Sikorsky S-76 helicopters commercially operated in the Gulf Coast region of Louisiana. Fatigue tests were conducted for a graphite/epoxy tail rotor spar and static test for a graphite/epoxy and Kevlar/epoxy stabilizer. Graphite/epoxy and Kevlar/epoxy panels are being exposed to the outdoor environment in Stratford, Connecticut and West Palm Beach, Florida. For this reporting period the two year panels were returned, moisture measurements taken, and strength tests conducted. Results are compared with initial type certificate strengths for components and with initial laboratory coupon tests for the exposed panels. Comparisons are also presented with predicted and measured moisture contents.

Flight service evaluation of composite helicopter components

NASA Technical Reports Server (NTRS)

Rich, M. J.; Lowry, D. W.

1982-01-01

This first interim report presents the technical background for including environmental effects in the design of helicopter composite structures, and test results after approximately two year field exposure of components and panels. Composite structural components were removed from Sikorsky S-76 helicopters commercially operated in the Gulf Coast region of Louisiana. Fatigue tests were conducted for a graphite/epoxy tail rotor spar and static test for a graphite/epoxy and Kevlar/epoxy stabilizer. Graphite/epoxy and Kevlar/epoxy panels are being exposed to the outdoor environment in Stratford, Connecticut and West Palm Beach, Florida. For this reporting period the two year panels were returned, moisture measurements taken, and strength tests conducted. Results are compared with initial type certificate strengths for components and with initial laboratory coupon tests for the exposed panels. Comparisons are also presented with predicted and measured moisture contents.

Truck characteristics analysis

DOT National Transportation Integrated Search

1998-01-01

This report documents the early observations from the Long-Term Pavement Performance (LTPP) Specific Pavement Studies (SPS) conducted as part of the LTPP Program Data Insight conducted to identify initial findings from the test sections established f...

Structural tests on space shuttle thermal protection system constructed with nondensified and densified Li 900 and LI 2200 tile

NASA Technical Reports Server (NTRS)

Williams, J. G.

1981-01-01

Structural tests were conducted on thermal protection systems (TPS) LI 900 and LI 2200 tiles and .41 cm and .23 cm thick strain isolation pads. The bond surface of selected tiles was densified to obtain improved strength. Four basic types of experiments were conducted including tension tests, substrate mismatch (initial imperfection) tests, tension loads eccentrically applied, and pressure loads applied rapidly to the tile top surface. A small initial imperfection mismatch (2.29 m spherical radius on the substrate) did not influence significantly the ultimate failure strength. Densification of the tile bond region improved the strength of TPS constructed both of LI 900 tile and of LI 2200 tile. Pressure shock conditions studied did not significantly affect the TPS strength.

Defense Enterprise Accounting and Management System (DEAMS) Increment 1 Release 3 Initial Operational Test and Evaluation Report

DTIC Science & Technology

2015-08-01

Initial Operational Test and Evaluation ( IOT &E) and the system’s operational effectiveness, operational suitability, and cybersecurity. The Air Force...Operational Test and Evaluation Center (AFOTEC) conducted the IOT &E between October 1, 2014, and May 29, 2015, at seven bases that included three...at McConnell Air Force Base (AFB), Kansas. Adequacy of IOT &E The IOT &E was adequate and was executed in accordance with the Test and Evaluation

Implementation and Initial Validation of the APS English Test [and] The APS English-Writing Test at Golden West College: Evidence for Predictive Validity.

ERIC Educational Resources Information Center

Isonio, Steven

In May 1991, Golden West College (California) conducted a validation study of the English portion of the Assessment and Placement Services for Community Colleges (APS), followed by a predictive validity study in July 1991. The initial study was designed to aid in the implementation of the new test at GWC by comparing data on APS use at other…

Pretest Caluculations of Temperature Changes for Field Thermal Conductivity Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

N.S. Brodsky

A large volume fraction of the potential monitored geologic repository at Yucca Mountain may reside in the Tptpll (Tertiary, Paintbrush Group, Topopah Spring Tuff, crystal poor, lower lithophysal) lithostratigraphic unit. This unit is characterized by voids, or lithophysae, which range in size from centimeters to meters. A series of thermal conductivity field tests are planned in the Enhanced Characterization of the Repository Block (ECRB) Cross Drift. The objective of the pretest calculation described in this document is to predict changes in temperatures in the surrounding rock for these tests for a given heater power and a set of thermal transportmore » properties. The calculation can be extended, as described in this document, to obtain thermal conductivity, thermal capacitance (density x heat capacity, J {center_dot} m{sup -3} {center_dot} K{sup -1}), and thermal diffusivity from the field data. The work has been conducted under the ''Technical Work Plan For: Testing and Monitoring'' (BSC 2001). One of the outcomes of this analysis is to determine the initial output of the heater. This heater output must be sufficiently high that it will provide results in a reasonably short period of time (within several weeks or a month) and be sufficiently high that the heat increase is detectable by the instruments employed in the test. The test will be conducted in stages and heater output will be step increased as the test progresses. If the initial temperature is set too high, the experiment will not have as many steps and thus fewer thermal conductivity data points will result.« less

40 CFR 62.14675 - By what date must I conduct the annual performance test?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 8 2011-07-01 2011-07-01 false By what date must I conduct the annual... Commenced Construction On or Before November 30, 1999 Continuous Compliance Requirements § 62.14675 By what... particulate matter, hydrogen chloride, and opacity within 12 months following the initial performance test...

Individual Learning Account Pilot Initiative: A Learning Tool for the 21st Century. Report to the OPM Director.

ERIC Educational Resources Information Center

President's Task Force on Federal Training Technology, Washington, DC.

The U.S. Office of Personnel Management (OPM) evaluated the feasibility of individual learning accounts (ILAs) as an approach to workforce development. Thirteen federal agencies volunteered to participate in the initiative. Together, they conducted a total of 17 pilot tests. Some pilot tests included all employees in the agency. Others targeted…

Thermal conductance measurements of bolted copper joints for SuperCDMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmitt, R.; Tatkowski, Greg; Ruschman, M.

2015-09-01

Joint thermal conductance testing has been undertaken for bolted copper to copper connections from 60 mK to 26 K. This testing was performed to validate an initial design basis for the SuperCDMS experiment, where a dilution refrigerator will be coupled to a cryostat via multiple bolted connections. Copper used during testing was either gold plated or passivated with citric acid to prevent surface oxidation. Results obtained are well fit by a power law regression of joint thermal conductance to temperature and match well with data collected during a literature review.

40 CFR 63.9911 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... your existing affected source; (2) By April 7, 2004 for a new source that has an initial startup date before October 10, 2003; or (3) Within 180 days after initial startup for a new source that has an initial startup date after October 10, 2003. (b) For each operation and maintenance requirement that...

40 CFR 63.9911 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2012 CFR

2012-07-01

... your existing affected source; (2) By April 7, 2004 for a new source that has an initial startup date before October 10, 2003; or (3) Within 180 days after initial startup for a new source that has an initial startup date after October 10, 2003. (b) For each operation and maintenance requirement that...

40 CFR 63.9911 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... your existing affected source; (2) By April 7, 2004 for a new source that has an initial startup date before October 10, 2003; or (3) Within 180 days after initial startup for a new source that has an initial startup date after October 10, 2003. (b) For each operation and maintenance requirement that...

40 CFR 63.9911 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... your existing affected source; (2) By April 7, 2004 for a new source that has an initial startup date before October 10, 2003; or (3) Within 180 days after initial startup for a new source that has an initial startup date after October 10, 2003. (b) For each operation and maintenance requirement that...

40 CFR 63.9911 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2014 CFR

2014-07-01

... your existing affected source; (2) By April 7, 2004 for a new source that has an initial startup date before October 10, 2003; or (3) Within 180 days after initial startup for a new source that has an initial startup date after October 10, 2003. (b) For each operation and maintenance requirement that...

40 CFR 63.7 - Performance testing requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Performance testing requirements. (a) Applicability and performance test dates. (1) The applicability of this... or operator of the affected source must perform such tests within 180 days of the compliance date for... standard initially, the owner or operator shall conduct a second performance test within 3 years and 180...

Development and qualification testing of a laser-ignited, all-secondary (DDT) detonator

NASA Technical Reports Server (NTRS)

Blachowski, Thomas J.; Krivitsky, Darrin Z.; Tipton, Stephen

1994-01-01

The Indian Head Division, Naval Surface Warfare Center (IHDIV, NSWC) is conducting a qualification program for a laser-ignited, all-secondary (DDT) explosive detonator. This detonator was developed jointly by IHDIV, NSWC and the Department of Energy's EG&G Mound Applied Technologies facility in Miamisburg, Ohio to accept a laser initiation signal and produce a fully developed shock wave output. The detonator performance requirements were established by the on-going IHDIV, NSWC Laser Initiated Transfer Energy Subsystem (LITES) advanced development program. Qualification of the detonator as a component utilizing existing military specifications is the selected approach for this program. The detonator is a deflagration-to-detonator transfer (DDT) device using a secondary explosive, HMX, to generate the required shock wave output. The prototype development and initial system integration tests for the LITES and for the detonator were reported at the 1992 International Pyrotechnics Society Symposium and at the 1992 Survival and Flight Equipment National Symposium. Recent results are presented for the all-fire sensitivity and qualification tests conducted at two different laser initiation pulses.

Pretest Plan for a Quarter Scale AFT Segment of the SRB Filament Wound Case in the NSWC Hydroballistics Facility. [space shuttle boosters

NASA Technical Reports Server (NTRS)

Adoue, J. A.

1984-01-01

In support of preflight design loads definition, preliminary water impact scale model are being conducted of space shuttle rocket boosters. The model to be used as well as the instrumentation, test facilities, and test procedures are described for water impact tests being conducted at test conditions to simulate full-scale initial impact at vertical velocities from 65 to 85 ft/sec. zero horizontal velocity, and angles of 0,5, and 10 degrees.

Status of the NOAO evaluation of the Hughes 20x64 Si:As impurity band conduction array. [for ground and space-based astronomy

NASA Technical Reports Server (NTRS)

Fowler, A. M.; Joyce, R. R.

1990-01-01

The Hughes 20 x 64 Si:As impurity band conduction arrays designed for ground-based and spaceborne astronomy observations is described together with experiments performed at NOAO to test these arrays. Special attention is given to the design and the characteristics of the test system and to the test methods. The initial tests on two columns of one array indicate that the array is easy to operate and performed satisfactorily.

Field evaluation of a behavioral test battery for DWI

DOT National Transportation Integrated Search

1983-09-01

This paper presents initial findings from a recently conducted field evaluation of a sobriety test battery. Police officers from four jurisdictions were trained in the use of the sobriety test battery. They then administered the battery to drivers st...

40 CFR 60.2690 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Performance Testing...

40 CFR 60.2690 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Performance Testing...

40 CFR 63.3960 - By what date must I conduct performance tests and other initial compliance demonstrations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... compliance date specified in § 63.3883. For magnet wire coating operations you may, with approval, conduct a performance test of one representative magnet wire coating machine for each group of identical or very similar magnet wire coating machines. (2) You must develop and begin implementing the work practice plan required...

40 CFR 63.7320 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Initial Compliance... coke oven battery stack by the compliance date that is specified in § 63.7283. (c) For each work...

40 CFR 63.7320 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Initial Compliance... coke oven battery stack by the compliance date that is specified in § 63.7283. (c) For each work...

40 CFR 63.7320 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Initial Compliance... coke oven battery stack by the compliance date that is specified in § 63.7283. (c) For each work...

40 CFR 63.7320 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Initial Compliance... coke oven battery stack by the compliance date that is specified in § 63.7283. (c) For each work...

40 CFR 63.8230 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Hazardous Air Pollutants: Mercury Emissions From Mercury Cell Chlor-Alkali Plants Initial Compliance... § 63.8190(a)(2) for by-product hydrogen streams and end box ventilation system vents and the applicable...

40 CFR 63.8230 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Hazardous Air Pollutants: Mercury Emissions From Mercury Cell Chlor-Alkali Plants Initial Compliance... § 63.8190(a)(2) for by-product hydrogen streams and end box ventilation system vents and the applicable...

40 CFR 63.8230 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Hazardous Air Pollutants: Mercury Emissions From Mercury Cell Chlor-Alkali Plants Initial Compliance... § 63.8190(a)(2) for by-product hydrogen streams and end box ventilation system vents and the applicable...

40 CFR 63.8230 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Hazardous Air Pollutants: Mercury Emissions From Mercury Cell Chlor-Alkali Plants Initial Compliance... § 63.8190(a)(2) for by-product hydrogen streams and end box ventilation system vents and the applicable...

40 CFR 63.8230 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Pollutants: Mercury Emissions From Mercury Cell Chlor-Alkali Plants Initial Compliance Requirements § 63.8230...(a)(2) for by-product hydrogen streams and end box ventilation system vents and the applicable...

Federal Highway Administration Focus States Initiative : traffic incident management performance measures final report

DOT National Transportation Integrated Search

2009-12-01

The Traffic Incident Management Performance Measures Focus States Initiative (TIM PM FSI) involves 11 States that have defined three traffic incident performance measures (PM) and conducted field tests of two of these measures. The following measures...

Operational evaluation of initial data link air traffic control services, Vol. 1

DOT National Transportation Integrated Search

1990-02-01

This report details the results of an operational evaluation of Initial Data Link Air Traffic Control (ATC) Services. The Operational Evaluation was conducted at the Federal Aviation Administration (FAA) Technical Center utilizing the Data Link test ...

Traveler Phase 1A Joint Review

NASA Technical Reports Server (NTRS)

St. John, Clint; Scofield, Jan; Skoog, Mark; Flock, Alex; Williams, Ethan; Guirguis, Luke; Loudon, Kevin; Sutherland, Jeffrey; Lehmann, Richard; Garland, Michael;

A Strategic Defense Initiative Organization Software Testing Initiative

DTIC Science & Technology

1990-10-01

One group of researchers is investigating a version of this analysis termed constrained expression analysis [Dillon 1988c]. Here a design is...examined. Academic researchers will assist in developing experiments. In addition, an organization or group of people will be identified 14 as the focal...to make the transition into common practice. Research is being conducted into control -based test data adequacy criteria to support the dynamic

Implementation and Initial Validation of the MDTP Tests at Golden West College.

ERIC Educational Resources Information Center

Isonio, Steven

In 1992, a study was conducted at Golden West College (California) to determine the predictive validity of the Math Diagnostic Testing Project (MDTP) tests. A total of 1,137 students were tested in-class; 601 took the Algebra Readiness test, 376 took the Elementary Algebra test, and 160 took the Intermediate Algebra test. Two correlation…

Ares I-X USS Material Testing

NASA Technical Reports Server (NTRS)

Dawicke, David S.; Smith, Stephen W.; Raju, Ivatury S.

2008-01-01

An independent assessment was conducted to determine the critical initial flaw size (CIFS) for the flange-to-skin weld in the Ares I-X Upper Stage Simulator (USS). Material characterization tests were conducted to quantify the material behavior for use in the CIFS analyses. Fatigue crack growth rate, Charpy impact, and fracture tests were conducted on the parent and welded A516 Grade 70 steel. The crack growth rate tests confirmed that the material behaved in agreement with literature data and that a salt water environment would not significantly degrade the fatigue resistance. The Charpy impact tests confirmed that the fracture resistance of the material did not have a significant reduction for the expected operational temperatures of the vehicle.

40 CFR 90.509 - Calculation and reporting of test results.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Calculation and reporting of test... Selective Enforcement Auditing § 90.509 Calculation and reporting of test results. (a) Initial test results... the number of tests conducted on the engine, and rounding to the same number of decimal places...

IDAS : ITS Deployment Analysis System

DOT National Transportation Integrated Search

1997-05-01

This report documents the activities and results of a 2-year test of non-intrusive traffic detection technologies. The test was initiated by the Federal Highway Administration (FHWA) and conducted by the Minnesota Department of Transportation (Mn/DOT...

NASA Processes and Requirements for Conducting Human-in-the-Loop Closed Chamber Tests

NASA Technical Reports Server (NTRS)

Barta, Daniel J.; Montz, Michael E.

2004-01-01

NASA has specific processes and requirements that must be followed for tests involving human subjects to be conducted in a safe and effective manner. There are five distinct phases of test operations. Phase one, the test request phase, consists of those activities related to initiating, processing, reviewing, and evaluating the test request. Phase two, the test preparation phase consists of those activities related to planning, coordinating, documenting, and building up the test. Phase three, the test readiness phase consists of those activities related to verifying and reviewing the planned test operations. Phase four, the test activity phase, consists of all pretest operations, functional checkouts, emergency drills, and test operations. Phase five, the post test activity phase, consists of those activities performed once the test is completed, including briefings, documentation of anomalies, data reduction and archiving, and reporting. Project management processes must be followed for facility modifications and major test buildup, which include six phases: initiation and assessment, requirements evaluation, preliminary design, detailed design, use readiness review (URR) and acceptance. Compliance with requirements for safety and quality assurance are documented throughout the test buildup and test operation processes. Tests involving human subjects must be reviewed by the applicable Institutional Review Board (IRB).

40 CFR 63.5840 - By what date must I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Open molding and centrifugal casting operations that elect to meet an organic HAP emissions limit on a 12-month rolling average must initiate collection of the required data on the compliance date, and...

40 CFR 63.5840 - By what date must I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Open molding and centrifugal casting operations that elect to meet an organic HAP emissions limit on a 12-month rolling average must initiate collection of the required data on the compliance date, and...

40 CFR 63.5840 - By what date must I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Open molding and centrifugal casting operations that elect to meet an organic HAP emissions limit on a 12-month rolling average must initiate collection of the required data on the compliance date, and...

40 CFR 63.5840 - By what date must I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Open molding and centrifugal casting operations that elect to meet an organic HAP emissions limit on a 12-month rolling average must initiate collection of the required data on the compliance date, and...

Predictors of provider- initiated HIV testing and counseling refusal by outpatient department clients in Wolaita zone, Southern Ethiopia: a case control study.

PubMed

Facha, Wolde; Kassahun, Wondewosen; Workicho, Abdulhalik

2016-08-12

Despite different strategies designed to rapidly identify HIV infected individuals, majority of HIV-infected people are unaware of their sero-status in developing countries. The objective of this study was to assess predictors of provider-initiated HIV testing and counseling (PITC) refusal by outpatient department (OPD) clients in Wolaita zone, Southern Ethiopia. Facility based unmatched case control study was conducted on outpatient department clients in randomly selected seven health facilities in Wolaita zone, Southern Ethiopia in February 2012. A total of 291 participants (97 cases and 194 controls) were included in our study. Cases were patients who refused HIV test while controls were patients who tested for HIV after provider-initiated HIV testing and counseling (PITC) recommendation by outpatient department (OPD) clinicians. We used both quantitative and qualitative methods of data collection. Pretested interviewer administered questionnaires were used to collect quantitative data by trained nurses, and in-depth interview with 14 OPD clinicians was conducted by principal investigator to supplement quantitative findings. Bivariate and multivariate analyses were done to identify independent predictors of provider-initiated HIV testing and counseling refusal by OPD clients. Study participants who had stigmatizing attitude [AOR = 6.09, (95 % CI: 1.70, 21.76)], who had perceived risk for HIV infection [AOR = 5.23, (95 % CI: 2.22, 12.32)], who did not perceive the benefits of provider-initiated HIV testing and counseling [AOR = 4.64, (95 % CI: 1.79, 12.01)], who did not get minimum recommended pretest information from their providers [AOR = 2.98, (95 % CI: 1.06, 8.35)], who ever not heard of provider-initiated HIV testing and counseling service [AOR = 2.41, (95 % CI: 1.14, 5.09)], and who were from urban area [AOR = 2.40, (95 % CI = 1.26, 4.57)] were more likely to refuse provider-initiated HIV testing and counseling service than their counterparts. Knowledge on HIV/AIDS, attitude towards people living with HIV/AIDS and perceived risk for HIV infection by clients were the major barriers for provider-initiated HIV testing and counseling acceptance. Health professionals working at outpatient department should give due attention to overcome these barriers so as to enhance HIV testing acceptance by their clients.

Thermal conductance measurements of bolted copper joints for SuperCDMS

DOE PAGES

Schmitt, R. L.; Tatkowski, G.; Ruschman, M.; ...

2015-04-28

Joint thermal conductance testing has been undertaken for bolted copper to copper connections from 60 mK to 26 K. This testing was performed to validate an initial design basis for the SuperCDMS experiment, where a dilution refrigerator will be coupled to a cryostat via multiple bolted connections. Copper used during testing was either gold plated or passivated with citric acid to prevent surface oxidation. Finally, the results we obtained are well fit by a power law regression of joint thermal conductance to temperature and match well with data collected during a literature review.

Passenger rail train-to-train impact test. Volume 1 : overview and selected results

DOT National Transportation Integrated Search

2003-07-01

This report describes the results of the train-to-train impact test conducted at the Federal Railroad Administration's Transportation Technology Center in Pueblo, Colorado on January 31, 2002. In this test, a cab car-led train, initially moving at 30...

Train-to-train impact test : analysis of structural measurements

DOT National Transportation Integrated Search

2002-11-17

This paper describes the results of the train-to-train impact test conducted at the Transportation Technology Center in Pueblo, Colorado on January 31, 2002. In this test, a cab car-led train, initially moving at 30 mph, collided with a standing loco...

Feasibility test of CADD Webmenus.

DOT National Transportation Integrated Search

2009-08-01

The Arizona Department of Transportation (ADOT) initiated SPR Project 683: CADD Webmenus Feasibility Study to conduct a proof-of-concept test of Web-based CADD menus for ADOT agency-wide CADD applications. ADOT is currently interested in the feasibil...

40 CFR 63.5850 - How do I conduct performance tests, performance evaluations, and design evaluations?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Pollutants: Reinforced Plastic Composites Production Testing and Initial Compliance Requirements § 63.5850... exhaust stream exceeds five, you must take into account the use of multiple chromatographic columns and...

40 CFR 63.5850 - How do I conduct performance tests, performance evaluations, and design evaluations?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Pollutants: Reinforced Plastic Composites Production Testing and Initial Compliance Requirements § 63.5850... exhaust stream exceeds five, you must take into account the use of multiple chromatographic columns and...

40 CFR 63.5850 - How do I conduct performance tests, performance evaluations, and design evaluations?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Pollutants: Reinforced Plastic Composites Production Testing and Initial Compliance Requirements § 63.5850... exhaust stream exceeds five, you must take into account the use of multiple chromatographic columns and...

The effects of free recall testing on subsequent source memory.

PubMed

Brewer, Gene A; Marsh, Richard L; Meeks, Joseph T; Clark-Foos, Arlo; Hicks, Jason L

2010-05-01

The testing effect is the finding that prior retrieval of information from memory will result in better subsequent memory for that material. One explanation for these effects is that initial free recall testing increases the recollective details for tested information, which then becomes more available during a subsequent test phase. In three experiments we explored this hypothesis using a source-monitoring test phase after the initial free recall tests. We discovered that memory is differentially enhanced for certain recollective details depending on the nature of the free recall task. Thus further research needs to be conducted to specify how different kinds of memorial details are enhanced by free recall testing.

75 FR 75485 - Current List of Laboratories Which Meet Minimum Standards To Engage in Urine Drug Testing for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-03

... Current List of Laboratories Which Meet Minimum Standards To Engage in Urine Drug Testing for Federal... Guidelines for Federal Workplace Drug Testing Programs (Mandatory Guidelines). The Mandatory Guidelines were... Laboratories and Instrumented Initial Testing Facilities (IITF) must meet in order to conduct drug and specimen...

75 FR 62842 - Current List of Laboratories Which Meet Minimum Standards To Engage in Urine Drug Testing for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-13

... Current List of Laboratories Which Meet Minimum Standards To Engage in Urine Drug Testing for Federal... Guidelines for Federal Workplace Drug Testing Programs (Mandatory Guidelines). The Mandatory Guidelines were... and Instrumented Initial Testing Facilities (IITF) must meet in order to conduct drug and specimen...

Impact of organizational factors on adherence to laboratory testing protocols in adult HIV care in Lusaka, Zambia.

PubMed

Deo, Sarang; Topp, Stephanie M; Westfall, Andrew O; Chiko, Matimbo M; Wamulume, Chibesa S; Morris, Mary; Reid, Stewart

2012-05-02

Previous operational research studies have demonstrated the feasibility of large-scale public sector ART programs in resource-limited settings. However, organizational and structural determinants of quality of care have not been studied. We estimate multivariate regression models using data from 13 urban HIV treatment facilities in Zambia to assess the impact of structural determinants on health workers' adherence to national guidelines for conducting laboratory tests such as CD4, hemoglobin and liver function and WHO staging during initial and follow-up visits as part of Zambian HIV care and treatment program. CD4 tests were more routinely ordered during initial history and physical (IHP) than follow-up (FUP) visits (93.0 % vs. 85.5 %; p < 0.01). More physical space, higher staff turnover and greater facility experience with ART was associated with greater odds of conducting tests. Higher staff experience decreased the odds of conducting CD4 tests in FUP (OR 0.93; p < 0.05) and WHO staging in IHP visit (OR 0.90; p < 0.05) but increased the odds of conducting hemoglobin test in IHP visit (OR 1.05; p < 0.05). Higher staff burnout increased the odds of conducting CD4 test during FUP (OR 1.14; p < 0.05) but decreased the odds of conducting hemoglobin test in IHP visit (0.77; p < 0.05) and CD4 test in IHP visit (OR 0.78; p < 0.05). Physical space plays an important role in ensuring high quality care in resource-limited setting. In the context of protocolized care, new staff members are likely to be more diligent in following the protocol verbatim rather than relying on memory and experience thereby improving adherence. Future studies should use prospective data to confirm the findings reported here.

Testing and Analytical Modeling for Purging Process of a Cryogenic Line

NASA Technical Reports Server (NTRS)

Hedayat, A.; Mazurkivich, P. V.; Nelson, M. A.; Majumdar, A. K.

2015-01-01

To gain confidence in developing analytical models of the purging process for the cryogenic main propulsion systems of upper stage, two test series were conducted. Test article, a 3.35m long with the diameter of 20 cm incline line, was filled with liquid (LH2)or gaseous hydrogen (GH2) and then purged with gaseous helium (GHe). Total of 10 tests were conducted. Influences of GHe flow rates and initial temperatures were evaluated. Generalized Fluid System Simulation Program (GFSSP), an in-house general-purpose fluid system analyzer, was utilized to model and simulate selective tests.

Performance of RASS vortex detection/measurement system

DOT National Transportation Integrated Search

1999-06-01

Preliminary tests conducted by WLR Research in the Fall of 1993 showed considerable promise that a Radio Acoustic Sounding System (RASS) was capable of detecting and tracking wake vortices located in the approach glide slope. Initial testing of the R...

40 CFR 63.5850 - How do I conduct performance tests, performance evaluations, and design evaluations?

Code of Federal Regulations, 2010 CFR

2010-07-01

...: Reinforced Plastic Composites Production Testing and Initial Compliance Requirements § 63.5850 How do I... exhaust stream exceeds five, you must take into account the use of multiple chromatographic columns and...

40 CFR 63.5850 - How do I conduct performance tests, performance evaluations, and design evaluations?

Code of Federal Regulations, 2011 CFR

2011-07-01

...: Reinforced Plastic Composites Production Testing and Initial Compliance Requirements § 63.5850 How do I... exhaust stream exceeds five, you must take into account the use of multiple chromatographic columns and...

SOIL WASHING TREATABILITY TESTS FOR PESTICIDE- CONTAMINATED SOIL

EPA Science Inventory

The 1987 Sand Creek Operable Unit 5 record of decision (ROD) identified soil washing as the selected technology to remediate soils contaminated with high levels of organochlorine pesticides, herbicides, and metals. Initial treatability tests conducted to assess the applicability...

Initiation and growth of multiple-site damage in the riveted lap joint of a curved stiffened fuselage panel: An experimental and analytical study

NASA Astrophysics Data System (ADS)

Ahmed, Abubaker Ali

As part of the structural integrity research of the National Aging Aircraft Research Program, a comprehensive study on multiple-site damage (MSD) initiation and growth in a pristine lap-joint fuselage panel has been conducted. The curved stiffened fuselage panel was tested at the Full-Scale Aircraft Structural Test Evaluation and Research (FASTER) facility located at the Federal Aviation Administration William J. Hughes Technical Center. A strain survey test was conducted to verify proper load application. The panel was then subjected to a fatigue test with constant-amplitude cyclic loading. The applied loading spectrum included underload marker cycles so that crack growth history could be reconstructed from post-test fractographic examinations. Crack formation and growth were monitored via nondestructive and high-magnification visual inspections. Strain gage measurements recorded during the strain survey tests indicated that the inner surface of the skin along the upper rivet row of the lap joint experienced high tensile stresses due to local bending. During the fatigue loading, cracks were detected by eddy-current inspections at multiple rivet holes along the upper rivet row. Through-thickness cracks were detected visually after about 80% of the fatigue life. Once MSD cracks from two adjacent rivet holes linked up, there was a quick deterioration in the structural integrity of the lap joint. The linkup resulted in a 2.87" (72.9-mm) lead fatigue crack that rapidly propagated across 12 rivet holes and crossed over into the next skin bay, at which stage the fatigue test was terminated. A post-fatigue residual strength test was then conducted by loading the panel quasi-statically up to final failure. The panel failed catastrophically when the crack extended instantaneously across three additional bays. Post-test fractographic examinations of the fracture surfaces in the lap joint of the fuselage panel were conducted to characterize subsurface crack initiation and growth. Results showed evidence of fretting damage and crack initiation at multiple locations near the rivet holes along the faying surface of the skin. The subsurface cracks grew significantly along the faying surface before reaching the outer surface of the skin, forming elliptical crack fronts. A finite element model (FE) of the panel was constructed and geometrically-nonlinear analyses conducted to determine strain distribution under the applied loads. The FE model was validated by comparing the analysis results with the strain gage measurements recorded during the strain survey test. The validated FE model was then used to determine stress-intensity factors at the crack tips. Stress-intensity factor results indicated that crack growth in the lap joint was under mixed-mode; however, the opening-mode stress intensity factor was dominant. The stress-intensity factors computed from the FE analysis were used to conduct cycle-by-cycle integration of fatigue crack growth. In the cycle-by-cycle integration, the NASGRO crack growth model was used with its parameters selected to account for the effects of plasticity-induced crack closure and the test environment on crack growth rate. Fatigue crack growth predictions from cycle-by-cycle computation were in good agreement with the experimental measured crack growth data. The results of the study provide key insights into the natural development and growth of MSD cracks in the pristine lap joint. The data provided by the study represent a valuable source for the evaluation and validation of analytical methodologies used for predicting MSD crack initiation and growth.

Controller Evaluation of Initial Data Link Air Traffic Control Services: Mini Study 2 Volume II

DOT National Transportation Integrated Search

1989-03-01

This report details the results of Mini Study 2. This Mini Study was conducted at the Federal Aviation Administration (FAA) Technical Center utilizing the Data Link test bed. Initial Data Link air traffic control services were evaluated under part ta...

Controller Evaluation of Initial Data Link Air Traffic Control Services: Mini Study 2 Volume I

DOT National Transportation Integrated Search

1989-03-01

This report details the results of Mini Study 2. This Mini Study was conducted at the Federal Aviation Administration (FAA) Technical Center utilizing the Data Link test bed. Initial Data Link air traffic control services were evaluated under part ta...

Using Impedance Spectroscopy to Assess the Viability of the Rapid Chloride Test for Determining Concrete Conductivity

PubMed Central

Snyder, K. A.; Ferraris, C.; Martys, N. S.; Garboczi, E. J.

2000-01-01

The suitability of using the initial current from the rapid chloride test (ASTM C 1202) to determine specimen conductivity is tested using impedance spectroscopy with a frequency spectrum of 10 Hz to 1 MHz. The specimen conductivity has an analytical relationship to specimen diffusivity and so is a useful quantity in service life prediction. Measurements made on specimens of different lengths indicate that the total charge passed during the six hour conduction test carried out according to ASTM C 1202 is not a direct measure of specimen conductivity. Further, ohmic heating during the 6 hour test makes it nearly impossible to directly measure any specimen transport property from the results. The total charge passed during the 6 hour conduction test is, therefore, not a reliable quantity for service life prediction. Results indicate that the direct current (dc) measurement of resistance using a voltage of 60 V is sufficient to overwhelm polarization effects, thereby yielding an accurate estimate of the true specimen conductivity. Impedance spectroscopy measurements also indicate that corrosion may form on the brass electrodes, adding bias to a conductivity estimate based upon a dc measurement. PMID:27551618

Journal: A Review of Some Tracer-Test Design Equations for Tracer-Mass Estimation and Sample Collection Frequency

EPA Science Inventory

Determination of necessary tracer mass, initial sample-collection time, and subsequent sample-collection frequency are the three most difficult aspects to estimate for a proposed tracer test prior to conducting the tracer test. To facilitate tracer-mass estimation, 33 mass-estima...

The Effect of Upper Body Mass and Initial Knee Flexion on the Injury Outcome of Post Mortem Human Subject Pedestrian Isolated Legs.

PubMed

Petit, Philippe; Trosseille, Xavier; Dufaure, Nicolas; Dubois, Denis; Potier, Pascal; Vallancien, Guy

2014-11-01

In the ECE 127 Regulation on pedestrian leg protection, as well as in the Euro NCAP test protocol, a legform impactor hits the vehicle at the speed of 40 kph. In these tests, the knee is fully extended and the leg is not coupled to the upper body. However, the typical configuration of a pedestrian impact differs since the knee is flexed during most of the gait cycle and the hip joint applies an unknown force to the femur. This study aimed at investigating the influence of the inertia of the upper body (modelled using an upper body mass fixed at the proximal end of the femur) and the initial knee flexion angle on the lower limb injury outcome. In total, 18 tests were conducted on 18 legs from 9 Post Mortem Human Subjects (PMHS). The principle of these tests was to impact the leg at 40 kph using a sled equipped with 3 crushing steel tubes, the stiffness of which were representative of the front face of a European sedan (bonnet leading edge, bumper and spoiler). The mass of the equipped sled was 74.5 kg. The test matrix was designed to perform 4 tests in 4 configurations combining two upper body masses (either 0 or 3 kg) and two knee angles (0 or 20 degrees) at 40 kph (11 m/s) plus 2 tests at 9 m/s. Autopsies were performed on the lower limbs and an injury assessment was established. The findings of this study were first that the increase of the upper body mass resulted in more severe injuries, second that an initial flexion of the knee, corresponding to its natural position during the gait cycle, decreased the severity of the injuries, and third that based on the injury outcome, a test conducted with no upper body mass and the knee fully extended was as severe as a test conducted with a 3 kg upper body mass and an initial knee flexion of 20°.

Tension and Bending Testing of an Integral T-Cap for Stitched Composite Airframe Joints

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.; Leone, Frank A., Jr.

2016-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body aircraft configuration. An important design feature required for assembly is the integrally stitched T-cap, which provides connectivity of the corner (orthogonal) joint between adjacent panels. A series of tests were conducted on T-cap test articles, with and without a rod stiffener penetrating the T-cap web, under tension (pull-off) and bending loads. Three designs were tested, including the baseline design used in large-scale test articles. The baseline had only the manufacturing stitch row adjacent to the fillet at the base of the T-cap web. Two new designs added stitching rows to the T-cap web at either 0.5- or 1.0-inch spacing along the height of the web. Testing was conducted at NASA Langley Research Center to determine the behavior of the T-cap region resulting from the applied loading. Results show that stitching arrests the initial delamination failures so that the maximum strength capability exceeds the load at which the initial delaminations develop. However, it was seen that the added web stitching had very little effect on the initial delamination failure load, but actually decreased the initial delamination failure load for tension loading of test articles without a stiffener passing through the web. Additionally, the added web stitching only increased the maximum load capability by between 1% and 12.5%. The presence of the stiffener, however, did increase the initial and maximum loads for both tension and bending loading as compared to the stringerless baseline design. Based on the results of the few samples tested, the additional stitching in the T-cap web showed little advantage over the baseline design in terms of structural failure at the T-cap web/skin junction for the current test articles.

40 CFR 63.7320 - By what date must I conduct performance tests or other initial compliance demonstrations?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Initial Compliance Requirements § 63.7320... limit for quench water in § 63.7295(a)(1) and each opacity limit in § 63.7297(a) for a by-product coke...

Pilot-in-the-Loop CFD Method Development

DTIC Science & Technology

2014-06-16

CFD analysis. Coupled simulations will be run at PSU on the COCOA -4 cluster, a high performance computing cluster. The CRUNCH CFD software has...been installed on the COCOA -4 servers and initial software tests are being conducted. Initial efforts will use the Generic Frigate Shape SFS-2 to

77 FR 32539 - Circular Welded Carbon-Quality Steel Pipe From the United Arab Emirates: Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

... Investigations; Request for Comment, 73 FR 26371 (May 9, 2008). A. Targeted Dumping Test We conducted customer..., 2011, the Department initiated the antidumping duty investigations on certain steel pipe from India... the Socialist Republic of Vietnam: Initiation of Antidumping Duty Investigations, 76 FR 72164...

40 CFR 63.1571 - How and when do I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2013 CFR

2013-07-01

... performance evaluation or test for a semi-regenerative catalytic reforming unit catalyst regenerator vent, you... properties. Examples of analytical methods include, but are not limited to: (i) Use of material balances...

40 CFR 63.1571 - How and when do I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2014 CFR

2014-07-01

... performance evaluation or test for a semi-regenerative catalytic reforming unit catalyst regenerator vent, you... properties. Examples of analytical methods include, but are not limited to: (i) Use of material balances...

40 CFR 63.1571 - How and when do I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2012 CFR

2012-07-01

... performance evaluation or test for a semi-regenerative catalytic reforming unit catalyst regenerator vent, you... properties. Examples of analytical methods include, but are not limited to: (i) Use of material balances...

Psychophysiology of Delayed Extinction and Reconsolidation in Humans

DTIC Science & Technology

2015-04-01

2013). Reconsolidation in a human fear conditioning study: a test of extinction as updating mechanism. Biological Psychology , 92(1), 43–50. doi...strengths of various pharmacological and behavioral, reconsolidation-blocking interventions could be tested . We completed testing for two...conductance, when assessing renewal and reinstatement. Mifepristone was tested as a second pharmacological intervention. After adjusting for initial

40 CFR 63.6612 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2011 CFR

2011-07-01

... stationary RICE with a site rating of less than or equal to 500 brake HP located at a major source of HAP emissions or an existing stationary RICE located at an area source of HAP emissions? 63.6612 Section 63.6612... other initial compliance demonstrations if I own or operate an existing stationary RICE with a site...

40 CFR 63.6612 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2010 CFR

2010-07-01

... stationary RICE with a site rating of less than or equal to 500 brake HP located at a major source of HAP emissions or an existing stationary RICE located at an area source of HAP emissions? 63.6612 Section 63.6612... other initial compliance demonstrations if I own or operate an existing stationary RICE with a site...

Western U.S.-Canada crossborder case study : activity 2 : task D : conduct regional and local trucking case studies

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Technical Capability Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM proje...

STOVL Hot Gas Ingestion control technology

NASA Technical Reports Server (NTRS)

Amuedo, K. C.; Williams, B. R.; Flood, J. D.; Johns, A. L.

1991-01-01

A comprehensive wind tunnel test program was conducted to evaluate control of Hot Gas Ingestion (HGI) on a 9.2 percent scale model of the McDonnell Aircraft Company model 279-3C advanced Short Takeoff and Vertical Landing (STOVL) configuration. The test was conducted in the NASA-Lewis Research Center 9 ft by 15 ft Low Speed Wind Tunnel during the summer of 1987. Initial tests defined baseline HGI levels as determined by engine face temperature rise and temperature distortion. Subsequent testing was conducted to evaluate HGI control parametrically using Lift Improvement Devices (LIDs), forward nozzle splay angle, a combination of LIDs and forward nozzle splay angle, and main inlet blocking. The results from this test program demonstrate that HGI can be effectively controlled and that HGI is not a barrier to STOVL aircraft development.

T-Cap Pull-Off and Bending Behavior for Stitched Structure

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.; Leone, Frank A., Jr.

2016-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body aircraft configuration. An important design feature required for assembly is the integrally stitched T-cap, which provides connectivity of the corner (orthogonal) joint between adjacent panels. A series of tests were conducted on T-cap test articles, with and without a rod stiffener penetrating the T-cap web, under tension (pull-off) and bending loads. Three designs were tested, including the baseline design used in largescale test articles. The baseline had only the manufacturing stitch row adjacent to the fillet at the base of the T-cap web. Two new designs added stitching rows to the T-cap web at either 0.5- or 1.0-inch spacing along the height of the web. Testing was conducted at NASA Langley Research Center to determine the behavior of the T-cap region resulting from the applied loading. Results show that stitching arrests the initial delamination failures so that the maximum strength capability exceeds the load at which the initial delaminations develop. However, it was seen that the added web stitching had very little effect on the initial delamination failure load, but actually decreased the initial delamination failure load for tension loading of test articles without a stiffener passing through the web. Additionally, the added web stitching only increased the maximum load capability by between 1% and 12.5%. The presence of the stiffener, however, did increase the initial and maximum loads for both tension and bending loading as compared to the stringerless baseline design. Based on the results of the few samples tested, the additional stitching in the T-cap web showed little advantage over the baseline design in terms of structural failure at the T-cap web/skin junction for the current test articles.

Effects of rational-emotive therapy on psychophysiological and reported measures of test anxiety arousal.

PubMed

Barabasz, A F; Barabasz, M

1981-07-01

Developed audio taped lectures, taped therapy session models, and homework assignments designed to reduce irrational beliefs associated with test anxiety within Ellis' rational-emotive therapy (RET) approach. The initial sample consisted of 148 university students. Comparisons with an attention placebo counseling program, which was established to be equally credible by a post-experiment inquiry and a no-treatment group found the RET Ss to show significantly lower skin conductance responses to a test anxiety visualization and lower reported anxiety on a questionnaire. However, skin conductance responses to an alternative test anxiety visualization did not show treatment effects.

Evaluation of the Mack Intelligent Vehicle Field Operational Test: September 2006

DOT National Transportation Integrated Search

2006-09-01

This report presents the final results of an independent evaluation of the U.S. Department of Transportation (USDOT) Mack Intelligent Vehicle Initiative (IVI) Field Operational Test (FOT). The IVI is a cooperative effort to conduct FOTs of advanced i...

Comparative Laboratory-Scale Testing of Dispersant Effectiveness of 23 Crude Oils Using Four Different Testing Protocols

EPA Science Inventory

A controlled laboratory study was conducted to measure the dispersion effectiveness of Corexit 9500 on 20 different crude oils. This study was a part of a larger project initiated by the Bureau of Safety and Environmental Enforcement (BSEE) testing 20 oils to compare the predict...

40 CFR 60.63 - Monitoring of operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... § 60.62, you must demonstrate compliance through an initial performance test. You will conduct your performance test using Method 5 or Method 5I at appendix A-3 to part 60 of this chapter. You must also monitor... CPMS, you will establish a site-specific operating limit. If your PM performance test demonstrates your...

40 CFR 60.63 - Monitoring of operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... § 60.62, you must demonstrate compliance through an initial performance test. You will conduct your performance test using Method 5 or Method 5I at appendix A-3 to part 60 of this chapter. You must also monitor... CPMS, you will establish a site-specific operating limit. If your PM performance test demonstrates your...

Engineering sciences area and module performance and failure analysis area

NASA Technical Reports Server (NTRS)

Ross, R. G., Jr.; Runkle, L. D.

1982-01-01

Photovoltaic-array/power-conditioner interface studies are updated. An experiment conducted to evaluate different operating-point strategies, such as constant voltage and pilot cells, and to determine array energy losses when the array is operated off the maximum power points is described. Initial results over a test period of three and a half weeks showed a 2% energy loss when the array is operated at a fixed voltage. Degraded-array studies conducted at NE RES that used a range of simulated common types of degraded I-V curves are reviewed. The instrumentation installed at the JPL field-test site to obtain the irradiance data was described. Experiments using an optical filter to adjust the spectral irradiance of the large-area pulsed solar simulator (LAPSS) to AM1.5 are described. Residential-array research activity is reviewed. Voltage isolation test results are described. Experiments performed on one type of module to determine the relationship between leakage current and temperature are reviewed. An encapsulated-cell testing approach is explained. The test program, data reduction methods, and initial results of long-duration module testing are described.

Single-Event Effect Testing of the Vishay Si7414DN n-Type TrenchFET(Registered Trademark) Power MOSFET

NASA Technical Reports Server (NTRS)

Lauenstein, J.-M.; Casey, M. C.; Campola, M. A.; Phan, A. M.; Wilcox, E. P.; Topper, A. D.; Ladbury, R. L.

2017-01-01

This study was being undertaken to determine the single event effect susceptibility of the commercial Vishay 60-V TrenchFET power MOSFET. Heavy-ion testing was conducted at the Texas AM University Cyclotron Single Event Effects Test Facility (TAMU) and the Lawrence Berkeley National Laboratory BASE Cyclotron Facility (LBNL). In addition, initial 200-MeV proton testing was conducted at Massachusetts General Hospital (MGH) Francis H. Burr Proton Beam Therapy Center. Testing was performed to evaluate this device for single-event effects from lower-LET, lighter ions relevant to higher risk tolerant space missions.

Data book for 12.5-inch diameter SRB thermal model water flotation test; 1.29 psia, series P022

NASA Technical Reports Server (NTRS)

Allums, S. L.

1974-01-01

Data acquired from tests conducted to determine how thermal conditions affect SRB (Space Shuttle Solid Rocket Booster) flotation at a scaled pressure of 1.29 psia are presented. Included are acceleration, pressure, and temperature data recorded from initial water impact to final flotation position using a 12.5-inch diameter thermal model of the SRB. Nineteen valid tests were conducted. These thermal tests indicated the following basic differences relative to the ambient temperature and pressure model tests: (1) more water was taken on board during penetration and (2) model flotation/sinking was temperature sensitive.

Overview of a stirling engine test project

NASA Technical Reports Server (NTRS)

Slaby, J. G.

1980-01-01

Tests were conducted on three Stirling engines ranging in size from 1.33 to 53 horsepower (1 to 40 kW). The tests were directed toward developing alternative, backup component concepts to improve engine efficiency and performance or to reduce costs. Some of the activities included investigating attractive concepts and materials for cooler-regenerator units, installing a jet impingement device on a Stirling engine to determine its potential for improved engine performance, and presenting performance maps for initial characterization of Stirling engines. The experiment results of the tests are presented along with predictions of results of future tests to be conducted on the Stirling engines.

Gravity Effect on Capillary Limit in a Miniature Loop Heat Pipe with Multiple Evaporators and Multiple Condensers

NASA Technical Reports Server (NTRS)

Nagano, Hosei; Ku, Jentung

2007-01-01

This paper describes the gravity effect on heat transport characteristics in a minia6re loop heat pipe with multiple evaporators and multiple condensers. Tests were conducted in three different orientations: horizontal, 45deg tilt, and vertical. The gravity affected the loop's natural operating temperature, the maximum heat transport capability, and the thermal conductance. In the case that temperatures of compensation chambers were actively controlled, the required control heater power was also dependent on the test configuration. In the vertical configuration, the secondary wick was not able to pump the liquid from the CC to the evaporator against the gravity. Thus the loop could operate stably or display some peculiar behaviors depending on the initial liquid distribution between the evaporator and the CC. Because such an initial condition was not known prior to the test, the subsequent loop performance was unpredictable.

Data book for 12.5-inch diameter SRB thermal model water flotation test: 14.7 psia, series P020

NASA Technical Reports Server (NTRS)

Allums, S. L.

1974-01-01

Data acquired from the initial series of tests conducted to determine how thermal conditions affect SRB (Space Shuttle Solid Rocket Booster) flotation are presented. Acceleration, pressure, and temperature data recorded from initial water impact to final flotation position using a 12.5-inch diameter thermal model of the SRB at ambient pressure are included. The model was 136.9 inches long and weighed 117.3 lbm. The tests indicated the following differences from ambient temperature tests: (1) significant negative static pressures can occur during penetration; (2) maximum penetration is increased; and (3) final flotation is in the spar buoy mode.

Analysis of Hyderabad Data from "Jolly Phonics" Initiative to Investigate Its Impact on Pupil Progress in Reading and Spelling--India

ERIC Educational Resources Information Center

Schagen, Ian; Shamsan, Yarim

2007-01-01

Private schooling in the third world is on the increase and in particular in one of the low-income areas of India, where a data analysis on Hyderabad has been carried out. The University of Newcastle has conducted an initiative research in Hyderabad on the impact on pupils' progress in Reading and Spelling tests. This initiative was called…

COLD TEMPERATURE MOTOR VEHICLE EMISSIONS TESTING IN ALASKA

EPA Science Inventory

A motor vehicle emissions testing study was conducted in Anchorage and Fairbanks during the winter of 1998-99 to collect actual measurements of initial idle emission rates. The study was performed for a sample of 111 automobiles and light-duty trucks under cold wintertime ambient...

Testing and Analytical Modeling for Purging Process of a Cryogenic Line

NASA Technical Reports Server (NTRS)

Hedayat, A.; Mazurkivich, P. V.; Nelson, M. A.; Majumdar, A. K.

2015-01-01

To gain confidence in developing analytical models of the purging process for the cryogenic main propulsion systems of upper stage, two test series were conducted. The test article, a 3.35 m long with the diameter of 20 cm incline line, was filled with liquid or gaseous hydrogen and then purged with gaseous helium (GHe). Total of 10 tests were conducted. The influences of GHe flow rates and initial temperatures were evaluated. The Generalized Fluid System Simulation Program (GFSSP), an in-house general-purpose fluid system analyzer computer program, was utilized to model and simulate selective tests. The test procedures, modeling descriptions, and the results are presented in the following sections.

Testing and Analytical Modeling for Purging Process of a Cryogenic Line

NASA Technical Reports Server (NTRS)

Hedayat, A.; Mazurkivich, P. V.; Nelson, M. A.; Majumdar, A. K.

2013-01-01

To gain confidence in developing analytical models of the purging process for the cryogenic main propulsion systems of upper stage, two test series were conducted. The test article, a 3.35 m long with the diameter of 20 cm incline line, was filled with liquid or gaseous hydrogen and then purged with gaseous helium (GHe). Total of 10 tests were conducted. The influences of GHe flow rates and initial temperatures were evaluated. The Generalized Fluid System Simulation Program (GFSSP), an in-house general-purpose fluid system analyzer computer program, was utilized to model and simulate selective tests. The test procedures, modeling descriptions, and the results are presented in the following sections.

Methodological approaches to conducting pilot and proof tests on reverse-osmosis systems: Results of comparative studies

NASA Astrophysics Data System (ADS)

Panteleev, A. A.; Bobinkin, V. V.; Larionov, S. Yu.; Ryabchikov, B. E.; Smirnov, V. B.; Shapovalov, D. A.

2017-10-01

When designing large-scale water-treatment plants based on reverse-osmosis systems, it is proposed to conduct experimental-industrial or pilot tests for validated simulation of the operation of the equipment. It is shown that such tests allow establishing efficient operating conditions and characteristics of the plant under design. It is proposed to conduct pilot tests of the reverse-osmosis systems on pilot membrane plants (PMPs) and test membrane plants (TMPs). The results of a comparative experimental study of pilot and test membrane plants are exemplified by simulating the operating parameters of the membrane elements of an industrial plant. It is concluded that the reliability of the data obtained on the TMP may not be sufficient to design industrial water-treatment plants, while the PMPs are capable of providing reliable data that can be used for full-scale simulation of the operation of industrial reverse-osmosis systems. The test membrane plants allow simulation of the operating conditions of individual industrial plant systems; therefore, potential areas of their application are shown. A method for numerical calculation and experimental determination of the true selectivity and the salt passage are proposed. An expression has been derived that describes the functional dependence between the observed and true salt passage. The results of the experiments conducted on a test membrane plant to determine the true value of the salt passage of a reverse-osmosis membrane are exemplified by magnesium sulfate solution at different initial operating parameters. It is shown that the initial content of a particular solution component has a significant effect on the change in the true salt passage of the membrane.

Force instrumentation for cryogenic wind tunnels using one-piece strain-gage balances

NASA Technical Reports Server (NTRS)

Ferris, A. T.

1980-01-01

The use of cryogenic temperatures in wind tunnels to achieve high Reynolds numbers has imposed a harsh operating environment on the force balance. Laboratory tests were conducted to study the effect cryogenic temperatures have on balance materials, gages, wiring, solder, adhesives, and moisture proofing. Wind tunnel tests were conducted using a one piece three component balance to verify laboratory results. These initial studies indicate that satisfactory force data can be obtained under steady state conditions.

Arundo Donax Analysis Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corrie I. Nichol, Ph.D.; Tyler L. Westover, Ph.D.

This is a summary report of preliminary analysis conducted on Arundo Donax. Arundo Donax was received from Greenwood Resources via Portland General Electric. PGE plans to transition a coal-fired boiler to 100% biomass by 2020, and has partnered with EPRI and INL to conduct the necessary testing and development to understand what needs to take place to make this transition. Arundo Donax is a promising energy crop for biopower, and is as yet relatively untested and uncharacterized. The INL has begun initial characterization of this material, and this summary report presents the initial findings.

40 CFR 63.11945 - What performance testing requirements must I meet for process vents?

Code of Federal Regulations, 2012 CFR

2012-07-01

... conduct the initial and periodic performance tests required in § 63.11925(d) and (e) and as specified in... tests under the conditions specified in paragraphs (b)(1) through (3) of this section, as applicable. Upon request, the owner or operator shall make available to the Administrator such records as may be...

40 CFR 63.11945 - What performance testing requirements must I meet for process vents?

Code of Federal Regulations, 2014 CFR

2014-07-01

... conduct the initial and periodic performance tests required in § 63.11925(d) and (e) and as specified in... tests under the conditions specified in paragraphs (b)(1) through (3) of this section, as applicable. Upon request, the owner or operator shall make available to the Administrator such records as may be...

40 CFR 63.11945 - What performance testing requirements must I meet for process vents?

Code of Federal Regulations, 2013 CFR

2013-07-01

... conduct the initial and periodic performance tests required in § 63.11925(d) and (e) and as specified in... tests under the conditions specified in paragraphs (b)(1) through (3) of this section, as applicable. Upon request, the owner or operator shall make available to the Administrator such records as may be...

49 CFR 232.205 - Class I brake test-initial terminal inspection.

Code of Federal Regulations, 2012 CFR

2012-10-01

... test shall be conducted as follows: (A) Charge the air brake system to the pressure at which the train... equivalent pressure maintaining locomotive brake valve, a railroad may use the Air Flow Method Test as an...) Charge the air brake system to the pressure at which the train will be operated, and the pressure at the...

49 CFR 232.205 - Class I brake test-initial terminal inspection.

Code of Federal Regulations, 2014 CFR

2014-10-01

... test shall be conducted as follows: (A) Charge the air brake system to the pressure at which the train... equivalent pressure maintaining locomotive brake valve, a railroad may use the Air Flow Method Test as an...) Charge the air brake system to the pressure at which the train will be operated, and the pressure at the...

49 CFR 232.205 - Class I brake test-initial terminal inspection.

Code of Federal Regulations, 2011 CFR

2011-10-01

... test shall be conducted as follows: (A) Charge the air brake system to the pressure at which the train... equivalent pressure maintaining locomotive brake valve, a railroad may use the Air Flow Method Test as an...) Charge the air brake system to the pressure at which the train will be operated, and the pressure at the...

49 CFR 232.205 - Class I brake test-initial terminal inspection.

Code of Federal Regulations, 2013 CFR

2013-10-01

... test shall be conducted as follows: (A) Charge the air brake system to the pressure at which the train... equivalent pressure maintaining locomotive brake valve, a railroad may use the Air Flow Method Test as an...) Charge the air brake system to the pressure at which the train will be operated, and the pressure at the...

Desert Research and Technology Studies (RATS) 2007 Field Campaign Objectives and Results

NASA Technical Reports Server (NTRS)

Kosmo, Joseph; Romig, Barbara

2008-01-01

Desert "RATS" (Research and Technology Studies) is a combined, multi-discipline group of inter-NASA center scientists and engineers, net-working and collaborating with representatives of industry and academia, for the purpose of conducting planetary surface exploration-focused remote field exercises. These integrated testing exercises conducted under representative analog Lunar and Mars surface terrain conditions, provide NASA the capability to validate experimental prototype hardware and software systems as well as to evaluate and develop mission operational techniques in order to identify and establish technical requirements and identify potential technology "gaps" applicable for future planetary human exploration. The 2007 D-RATS field campaign test activities were initiated based on the major themes and objectives of a notional 5-year plan developed for conducting relative analog test activities in support of the engineering evaluation and assessment of various system architectural requirements, conceptual prototype support equipment and selected technologies necessary for the establishment of a lunar outpost. Specifically, the major objectives included measuring task efficiency during robot, human, and human-robot interactive tasks associated with lunar outpost site surveying and reconnaissance activities and deployment of a representative solar panel power and distribution system. In addition, technology demonstrations were conducted with a new Lithium-ion battery and autonomous software to coordinate multiple robot activities. Secondary objectives were evaluating airlock concept mockups and prototype removable space suit over-garment elements for dust mitigation, and upgrades to the prototype extravehicular activities (EVA) communication and information system. Dry run test activities, prior to testing at a designated remote field site location, were initially conducted at the Johnson Space Center (JSC) Remote Field Demonstration Test Site. This is a multi-acre external test site located at JSC and has detailed representative terrain features simulating both Lunar and Mars surface characteristics. Both the local JSC and remote field test sites have terrain conditions that are representative and characteristic of both the Moon and Mars, such as strewn rock and volcanic ash fields, craters, rolling plains, hills, gullies, slopes, and outcrops. The D-RATS 2007 field campaign, representing the completion of its tenth year of analog testing, was conducted at the large Cinder Lake volcanic ash bed area adjacent to Flagstaff, Arizona.

ALOS-2 current status and operation plan

NASA Astrophysics Data System (ADS)

Suzuki, Shinichi; Kankaku, Yukihiro; Osawa, Yuji

2013-10-01

The Advanced Land Observing Satellite-2 (ALOS-2) carries the state-of-the-art L-band Synthetic Aperture Radar (SAR) called PALSAR-2 which succeeds to the ALOS / PALSAR. PALSAR-2 will have enhanced performance in both high resolution and wide swath compared to PALSAR. It will allow comprehensive monitoring of disasters. Wider bandwidth and shorter revisit time will give better conference for INSAR data analysis such as crustal deformation and deforestation. The Proto Flight Test (PFT) of ALOS-2 has been conducted since June 2012. In parallel, the PFT of PALSAR-2 has been conducted since March 2012. As of August 2013, ALOS-2 system has completed the interface test with ground system and is preparing for the Vibration test, Acoustic test and Electromagnetic Compatibility test. After completing these tests, ALOS-2 will be transported to JAXA Tanegashima Space Center for launch. The initial commissioning phase of ALOS-2 is planned for six months which are comprised of LEOP (Launch and Early Orbit Phase) and initial Cal/Val phase. During the LEOP, all components will be checked with direct downlink via Xband and with data relay communication via JAXA's DRTS (Data Relay Test Satellite). During the initial Cal/Val phase, the PALSAR-2 data will be verified and calibrated by using Corner Reflectors and Geometric Calibrator at ground. The data acquisition during the commissioning phase will be consistent with the systematic acquisition strategy prepared for the routine operation. This paper describes the current status and operation plan of ALOS-2.

Association Between Direct-to-Consumer Advertising and Testosterone Testing and Initiation in the United States, 2009-2013.

PubMed

Layton, J Bradley; Kim, Yoonsang; Alexander, G Caleb; Emery, Sherry L

2017-03-21

Testosterone initiation increased substantially in the United States from 2000 to 2013, especially among men without clear indications. Direct-to-consumer advertising (DTCA) also increased during this time. To investigate associations between televised DTCA and testosterone testing and initiation in the United States. Ecologic study conducted in designated market areas (DMAs) in the United States. Monthly testosterone advertising ratings were linked to DMA-level testosterone use data from 2009-2013 derived from commercial insurance claims. Associations between DTCA and testosterone testing, initiation, and initiation without recent baseline tests were estimated using Poisson generalized estimating equations. Monthly Nielsen ratings for testosterone DTCA in the 75 largest DMAs. (1) Rates of new serum testosterone testing; (2) rates of testosterone initiation (in-office injection, surgical implant, or pharmacy dispensing) for all testosterone products combined and for specific brands; and (3) rates of testosterone initiation without recent serum testosterone testing. Of 17 228 599 commercially insured men in the 75 DMAs, 1 007 990 (mean age, 49.6 [SD, 11.5] years) had new serum testosterone tests and 283 317 (mean age, 51.8 [SD, 11.3] years) initiated testosterone treatment. Advertising intensity varied by geographic region and time, with the highest intensity seen in the southeastern United States and with months ranging from no ad exposures to a mean of 13.6 exposures per household. Nonbranded advertisements were common prior to 2012, with branded advertisements becoming more common during and after 2012. Each household advertisement exposure was associated with a monthly increase in rates of new testosterone testing (rate ratio [RR], 1.006; 95% CI, 1.004-1.008), initiation (RR, 1.007; 95% CI, 1.004-1.010), and initiation without a recent test (RR, 1.008; 95% CI, 1.002-1.013). Mean absolute rate increases were 0.14 tests (95% CI, 0.09-0.19), 0.05 new initiations (95% CI, 0.03-0.08), and 0.02 initiations without a recent test (95% CI, 0.01-0.03) per 10 000 men for each monthly ad exposure over the entire period. Among US men residing in the 75 designated market areas, regional exposure to televised direct-to-consumer advertising was associated with greater testosterone testing, new initiation, and initiation without recent testing.

PIE on Safety-Tested AGR-1 Compact 5-1-1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunn, John D.; Morris, Robert Noel; Baldwin, Charles A.

Post-irradiation examination (PIE) is being performed in support of tristructural isotropic (TRISO) coated particle fuel development and qualification for High-Temperature Gas-cooled Reactors (HTGRs). AGR-1 was the first in a series of TRISO fuel irradiation experiments initiated in 2006 under the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program; this work continues to be funded by the Department of Energy's Office of Nuclear Energy as part of the Advanced Reactor Technologies (ART) initiative. AGR-1 fuel compacts were fabricated at Oak Ridge National Laboratory (ORNL) in 2006 and irradiated for three years in the Idaho National Laboratory (INL) Advanced Test Reactormore » (ATR) to demonstrate and evaluate fuel performance under HTGR irradiation conditions. PIE is being performed at INL and ORNL to study how the fuel behaved during irradiation, and to examine fuel performance during exposure to elevated temperatures at or above temperatures that could occur during a depressurized conduction cooldown event. This report summarizes safety testing of irradiated AGR-1 Compact 5-1-1 in the ORNL Core Conduction Cooldown Test Facility (CCCTF) and post-safety testing PIE.« less

Initial test results using the GEOS-3 engineering model altimeter

NASA Technical Reports Server (NTRS)

Hayne, G. S.; Clary, J. B.

1977-01-01

Data from a series of experimental tests run on the engineering model of the GEOS 3 radar altimeter using the Test and Measurement System (TAMS) designed for preflight testing of the radar altimeter are presented. These tests were conducted as a means of preparing and checking out a detailed test procedure to be used in running similar tests on the GEOS 3 protoflight model altimeter systems. The test procedures and results are also included.

An International Schools Perspective on Diagnosis and Treatment of Reading Disabilities.

ERIC Educational Resources Information Center

Balajthy, Ernest

A diagnostic evaluation was conducted on Thomas, a fifth-grade student, to identify levels of reading and major word identification strategies. Initial testing conducted at Thomas' home revealed that he appeared to have an unusually positive attitude toward reading, considering the difficulties it had presented him since kindergarten. Learning…

Best practices for implementing, testing and using a cloud-based communication system in a disaster situation.

PubMed

Makowski, Dale

2016-01-01

This paper sets out the basics for approaching the selection and implementation of a cloud-based communication system to support a business continuity programme, including: • consideration for how a cloud-based communication system can enhance a business continuity programme; • descriptions of some of the more popular features of a cloud-based communication system; • options to evaluate when selecting a cloud-based communication system; • considerations for how to design a system to be most effective for an organisation; • best practices for how to conduct the initial load of data to a cloud-based communication system; • best practices for how to conduct an initial validation of the data loaded to a cloud-based communication system; • considerations for how to keep contact information in the cloud-based communication system current and accurate; • best practices for conducting ongoing system testing; • considerations for how to conduct user training; • review of other potential uses of a cloud-based communication system; and • review of other tools and features many cloud-based communication systems may offer.

Hypervelocity Impact (HVI). Volume 6; WLE High Fidelity Specimen Fg(RCC)-2

NASA Technical Reports Server (NTRS)

Gorman, Michael R.; Ziola, Steven M.

2007-01-01

During 2003 and 2004, the Johnson Space Center's White Sands Testing Facility in Las Cruces, New Mexico conducted hypervelocity impact tests on the space shuttle wing leading edge. Hypervelocity impact tests were conducted to determine if Micro-Meteoroid/Orbital Debris impacts could be reliably detected and located using simple passive ultrasonic methods. The objective of Target Fg(RCC)-2 was to study hypervelocity impacts through the reinforced carbon-carbon (RCC) panels of the Wing Leading Edge. Fiberglass was used in place of RCC in the initial tests. Impact damage was detected using lightweight, low power instrumentation capable of being used in flight.

Hypervelocity Impact (HVI). Volume 4; WLE Small-Scale Fiberglass Panel Flat Target C-2

NASA Technical Reports Server (NTRS)

Gorman, Michael R.; Ziola, Steven M.

2007-01-01

During 2003 and 2004, the Johnson Space Center's White Sands Testing Facility in Las Cruces, New Mexico conducted hypervelocity impact tests on the space shuttle wing leading edge. Hypervelocity impact tests were conducted to determine if Micro-Meteoroid/Orbital Debris impacts could be reliably detected and located using simple passive ultrasonic methods. The objective of Target C-2 was to study impacts through the reinforced carboncarbon (RCC) panels of the Wing Leading Edge. Fiberglass was used in place of RCC in the initial tests. Impact damage was detected using lightweight, low power instrumentation capable of being used in flight.

Hypervelocity Impact (HVI). Volume 5; WLE High Fidelity Specimen Fg(RCC)-1

NASA Technical Reports Server (NTRS)

Gorman, Michael R.; Ziola, Steven M.

2007-01-01

During 2003 and 2004, the Johnson Space Center's White Sands Testing Facility in Las Cruces, New Mexico conducted hypervelocity impact tests on the space shuttle wing leading edge. Hypervelocity impact tests were conducted to determine if Micro-Meteoroid/Orbital Debris impacts could be reliably detected and located using simple passive ultrasonic methods. The objective of Target Fg(RCC)-1 was to study hypervelocity impacts through the reinforced carbon-carbon (RCC) panels of the Wing Leading Edge. Fiberglass was used in place of RCC in the initial tests. Impact damage was detected using lightweight, low power instrumentation capable of being used in flight.

Hypervelocity Impact (HVI). Volume 3; WLE Small-Scale Fiberglass Panel Flat Target C-1

NASA Technical Reports Server (NTRS)

Gorman, Michael R.; Ziola, Steven M.

2007-01-01

During 2003 and 2004, the Johnson Space Center's White Sands Testing Facility in Las Cruces, New Mexico conducted hypervelocity impact tests on the space shuttle wing leading edge. Hypervelocity impact tests were conducted to determine if Micro-Meteoroid/Orbital Debris impacts could be reliably detected and located using simple passive ultrasonic methods. The objective of Target C-1 was to study hypervelocity impacts on the reinforced carbon-carbon (RCC) panels of the Wing Leading Edge. Fiberglass was used in place of RCC in the initial tests. Impact damage was detected using lightweight, low power instrumentation capable of being used in flight.

40 CFR 63.1571 - How and when do I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2011 CFR

2011-07-01

... the option in paragraph (a)(1)(iii) in § 63.1564 (Ni lb/hr), and you use continuous parameter monitoring systems, you must establish an operating limit for the equilibrium catalyst Ni concentration based on the laboratory analysis of the equilibrium catalyst Ni concentration from the initial performance...

The Pittsburgh Girls Study: Overview and Initial Findings

ERIC Educational Resources Information Center

Keenan, Kate; Hipwell, Alison; Chung, Tammy; Stepp, Stephanie; Stouthamer-Loeber, Magda; Loeber, Rolf; McTigue, Kathleen

2010-01-01

The Pittsburgh Girls Study is a longitudinal, community-based study of 2,451 girls who were initially recruited when they were between the ages of 5 and 8 years. The primary aim of the study was testing developmental models of conduct disorder, major depressive disorder, and their co-occurrence in girls. In the current article, we summarize the…

National evaluation of the SafeTrip-21 initiative : I-95 corridor coalition test bed final evaluation report, North Carolina deployment of portable traffic-monitoring devices.

DOT National Transportation Integrated Search

2010-06-11

The purpose of this document is to present the findings of the national evaluation of the deployment of portable traffic monitoring devices (PTMDs) at a variety of locations in North Carolina conducted under the USDOTs SafeTrip-21 Initiative. The ...

National evaluation of the SafeTrip-21 initiative : I-95 corridor coalition test bed final evaluation report, North Carolina deployment of portable traffic-monitoring devices.

DOT National Transportation Integrated Search

2010-06-11

The purpose of this document is to present the findings of the national evaluation of the deployment of portable trafficmonitoring devices (PTMDs) at a variety of locations in North Carolina conducted under the USDOTs SafeTrip-21 Initiative. The N...

40 CFR 63.7530 - How do I demonstrate initial compliance with the emission limits and work practice standards?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Pollutants for Industrial, Commercial, and Institutional Boilers and Process Heaters Testing, Fuel Analyses... 5 and 7 to this subpart OR conducting initial fuel analyses to determine emission rates and... fuel subcategories that burn only fossil fuels and other gases and do not burn any residual oil must...

Hybrid bearings for LH2 and LO2 turbopumps

NASA Technical Reports Server (NTRS)

Butner, M. F.; Lee, F. C.

1985-01-01

Hybrid combinations of hydrostatic and ball bearings can improve bearing performance for liquid hydrogen and liquid oxygen turbopumps. Analytic studies were conducted to optimize hybrid bearing designs for the SSME-type turbopump conditions. A method to empirically determine damping coefficients was devised. Four hybrid bearing configurations were designed, and three were fabricated. Six hybrid and hydrostatic-only bearing configurations will be tested for steady-state and transient performance, and quantification of damping coefficients. The initial tests were conducted with the liquid hydrogen bearing.

40 CFR 63.4312 - What records must I keep?

Code of Federal Regulations, 2010 CFR

2010-07-01

... based on testing, you must keep the summary sheet of results provided to you by the manufacturer or... and printing materials. If you conducted testing to determine mass fraction of organic HAP of coating... operated within the operating scenarios used to demonstrate initial compliance, documentation that affected...

Modeling the Relationships between Subdimensions of Environmental Literacy

ERIC Educational Resources Information Center

Genc, Murat; Akilli, Mustafa

2016-01-01

The aim of this study is to demonstrate the relationships between subdimensions of environmental literacy using Structural Equation Modeling (SEM). The study was conducted by the analysis of students' answers to questionnaires data using SEM. Initially, Kaiser-Meyer-Olkin and Bartlett's tests were done to test appropriateness of subdimensions to…

Initiation of Insensitive High Explosives Using Multiple Wave Interactions

NASA Astrophysics Data System (ADS)

Francois, Elizabeth; Burritt, Rosmary; Biss, Matt; Bowden, Patrick

2017-06-01

Insensitive High Explosives (IHEs) increase safety in many types of weapons. However, the safety comes at the cost of performance. Initiation of IHE requires large boosters and powerful detonators as well. Multipoint initiation is being utilized to exploit explosive wave interactions to create overdriven states, greatly facilitating the initiation of IHEs. This presentation will build from recent explosive experiments where the minimum spot size for single-point initiation in PBX 9502 was determined. Below this threshold, PBX 9502 could not be initiated. This was then expanded to three initiation points, which were smaller this threshold. Measurements of the velocity and pressure of the wave interactions were measured using Photon Doppler Velocimetry (PDV). Initiation was observed, and the resulting pressures at the double and triple points were found to be above the CJ state for PBX 9502. Based on these results, further tests were conducted to isolate and measure the longevity and pressure of this phenomenon using cut-back tests. All results will be presented and discussed.

Sensitivity and validity of psychometric tests for assessing driving impairment: effects of sleep deprivation.

PubMed

Jongen, Stefan; Perrier, Joy; Vuurman, Eric F; Ramaekers, Johannes G; Vermeeren, Annemiek

2015-01-01

To assess drug induced driving impairment, initial screening is needed. However, no consensus has been reached about which initial screening tools have to be used. The present study aims to determine the ability of a battery of psychometric tests to detect performance impairing effects of clinically relevant levels of drowsiness as induced by one night of sleep deprivation. Twenty four healthy volunteers participated in a 2-period crossover study in which the highway driving test was conducted twice: once after normal sleep and once after one night of sleep deprivation. The psychometric tests were conducted on 4 occasions: once after normal sleep (at 11 am) and three times during a single night of sleep deprivation (at 1 am, 5 am, and 11 am). On-the-road driving performance was significantly impaired after sleep deprivation, as measured by an increase in Standard Deviation of Lateral Position (SDLP) of 3.1 cm compared to performance after a normal night of sleep. At 5 am, performance in most psychometric tests showed significant impairment. As expected, largest effect sizes were found on performance in the Psychomotor Vigilance Test (PVT). Large effects sizes were also found in the Divided Attention Test (DAT), the Attention Network Test (ANT), and the test for Useful Field of View (UFOV) at 5 and 11 am during sleep deprivation. Effects of sleep deprivation on SDLP correlated significantly with performance changes in the PVT and the DAT, but not with performance changes in the UFOV. From the psychometric tests used in this study, the PVT and DAT seem most promising for initial evaluation of drug impairment based on sensitivity and correlations with driving impairment. Further studies are needed to assess the sensitivity and validity of these psychometric tests after benchmark sedative drug use.

In situ recording of particle network formation in liquids by ion conductivity measurements.

PubMed

Pfaffenhuber, Christian; Sörgel, Seniz; Weichert, Katja; Bele, Marjan; Mundinger, Tabea; Göbel, Marcus; Maier, Joachim

2011-09-21

The formation of fractal silica networks from a colloidal initial state was followed in situ by ion conductivity measurements. The underlying effect is a high interfacial lithium ion conductivity arising when silica particles are brought into contact with Li salt-containing liquid electrolytes. The experimental results were modeled using Monte Carlo simulations and tested using confocal fluorescence laser microscopy and ζ-potential measurements.

A study on electrode gels for skin conductance measurements.

PubMed

Tronstad, Christian; Johnsen, Gorm Krogh; Grimnes, Sverre; Martinsen, Ørjan G

2010-10-01

Low-frequency skin conductance is used within several clinical applications and is mainly sensitive to sweating and the moisture content of the stratum corneum, but also how electrodes introduce changes in the electrical properties. Four electrode gels were investigated with regard to sorption characteristics and electrical properties. Skin conductance time series were collected from 18 test subjects during relaxation, exercise and recovery, wearing different pairs of electrodes contralaterally on the hypothenar and the T9 dermatome. Pressure test was applied on the T9 electrodes. Impedance frequency sweeps were taken on the T9 electrodes the same day and the next, parameterized to the Cole model. ANOVA on the initial skin conductance level change, exercise response amplitude, recovery offset and pressure-induced changes revealed significant differences among gel types. The wetter gels caused a higher positive level change, a greater response amplitude, larger recovery offset and greater pressure-induced artifacts compared to the solid gels. Sweating on the T9 site led to negative skin conductance responses for the wetter gels. Correlations were found between the desorption measurements and the initial skin conductance level change (hypothenar: R = 0.988 T9: R = 0.901) RM-ANOVA on the Cole parameters revealed a significant decrease in R(s) of the most resistive gel. Clinical implications are discussed.

Initial accomplishments of the Environmental Control and Life Support System (ECLSS) atmosphere revitalization (AR) predevelopment operational system test (POST) for the Space Station Freedom (SSF)

NASA Technical Reports Server (NTRS)

Dunn, Kevin H.; Bulgajewski, Peter J.

1992-01-01

Initial results of the integrated AR POST conducted by Boeing at Marshall Space Flight Center in 1992 are presented. The three baselined ECLSS Man Tended Capability AR assemblies were integrated and operated in a closed door chamber in which the internal atmosphere was monitored. The test provides a prerequisite checkout of the AR subsystem in preparation for longer duration tests in which the AR subsystem will be integrated with the Water Recovery Management subsystem. The integrated AR POST will serve as an early test bed to evaluate the integration of the space station ECLSS AR subsystem during design maturation.

Development of Advanced Thermal and Environmental Barrier Coatings Using a High-Heat-Flux Testing Approach

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Miller, Robert A.

2003-01-01

The development of low conductivity, robust thermal and environmental barrier coatings requires advanced testing techniques that can accurately and effectively evaluate coating thermal conductivity and cyclic resistance at very high surface temperatures (up to 1700 C) under large thermal gradients. In this study, a laser high-heat-flux test approach is established for evaluating advanced low conductivity, high temperature capability thermal and environmental barrier coatings under the NASA Ultra Efficient Engine Technology (UEET) program. The test approach emphasizes the real-time monitoring and assessment of the coating thermal conductivity, which initially rises under the steady-state high temperature thermal gradient test due to coating sintering, and later drops under the cyclic thermal gradient test due to coating cracking/delamination. The coating system is then evaluated based on damage accumulation and failure after the combined steady-state and cyclic thermal gradient tests. The lattice and radiation thermal conductivity of advanced ceramic coatings can also be evaluated using laser heat-flux techniques. The external radiation resistance of the coating is assessed based on the measured specimen temperature response under a laser- heated intense radiation-flux source. The coating internal radiation contribution is investigated based on the measured apparent coating conductivity increases with the coating surface test temperature under large thermal gradient test conditions. Since an increased radiation contribution is observed at these very high surface test temperatures, by varying the laser heat-flux and coating average test temperature, the complex relation between the lattice and radiation conductivity as a function of surface and interface test temperature may be derived.

40 CFR 63.11225 - What are my notification, reporting, and recordkeeping requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... combusted in any affected unit.” (5) If you are using data from a previously conducted emission test to... consistent with § 63.7(e)(2)(iv), you must submit the test data in lieu of the initial performance test... requirements of the petition process. (3) For sources that demonstrate compliance through fuel analysis, a copy...

Environmental Assessment of the Hawaii Geothermal Project Well Flow Test Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1976-11-01

The Hawaii Geothermal Project, a coordinated research effort of the University of Hawaii, funded by the County and State of Hawaii, and ERDA, was initiated in 1973 in an effort to identify, generate, and use geothermal energy on the Big Island of Hawaii. A number of stages are involved in developing geothermal power resources: exploration, test drilling, production testing, field development, power plant and powerline construction, and full-scale production. Phase I of the Project, which began in the summer of 1973, involved conducting exploratory surveys, developing analytical models for interpretation of geophysical results, conducting studies on energy recovery from hotmore » brine, and examining the legal and economic implications of developing geothermal resources in the state. Phase II of the Project, initiated in the summer of 1975, centers on drilling an exploratory research well on the Island of Hawaii, but also continues operational support for the geophysical, engineering, and socioeconomic activities delineated above. The project to date is between the test drilling and production testing phase. The purpose of this assessment is to describe the activities and potential impacts associated with extensive well flow testing to be completed during Phase II.« less

Test of LOX compatibility for asphalt and concrete runway materials

NASA Technical Reports Server (NTRS)

Moyers, C. V.; Bryan, C. J.; Lockhart, B. J.

1973-01-01

A literature survey and a telephone canvass of producers and users of LOX is reported which yielded one report of an accident resulting from a LOX spill on asphalt, one discussion of hazardous conditions, and an unreferenced mention of an incident. Laboratory tests using standard LOX impact apparatus yielded reactions with both old and new alphalt, but none with concrete. In the final test, using a larger sample of asphalt, the reaction caused extensive damage to equipment. Initial field experiments using 2-meter square asphalt slabs covered with LOX, conducted during rainy weather, achieved no reaction with plummets, and limited reaction with a blasting cap as a reaction initiator. In a final plummet-initiated test on a dry slab, a violent reaction, which appeared to have propagated over the entire slab surface, destroyed the plummet fixture and threw fragments as far as 48 meters.

Initial Effects of Heavy Vehicle Trafficking on Vegetated Soils

DTIC Science & Technology

2012-08-01

ER D C/ CR R EL T R -1 2 -6 Optimal Allocation of Land for Training and Non-training Uses ( OPAL ) Initial Effects of Heavy Vehicle...the outdoor loam test section. Optimal Allocation of Land for Training and Non-training Uses ( OPAL ) ERDC/CRREL TR-12-6 August 2012 Initial...mal Allocation of Land for Training and Non-Training Uses ( OPAL ) Pro- gram. The work was conducted by Nicole Buck and Sally Shoop of the Force

Improving the analysis of slug tests

USGS Publications Warehouse

McElwee, C.D.

2002-01-01

This paper examines several techniques that have the potential to improve the quality of slug test analysis. These techniques are applicable in the range from low hydraulic conductivities with overdamped responses to high hydraulic conductivities with nonlinear oscillatory responses. Four techniques for improving slug test analysis will be discussed: use of an extended capability nonlinear model, sensitivity analysis, correction for acceleration and velocity effects, and use of multiple slug tests. The four-parameter nonlinear slug test model used in this work is shown to allow accurate analysis of slug tests with widely differing character. The parameter ?? represents a correction to the water column length caused primarily by radius variations in the wellbore and is most useful in matching the oscillation frequency and amplitude. The water column velocity at slug initiation (V0) is an additional model parameter, which would ideally be zero but may not be due to the initiation mechanism. The remaining two model parameters are A (parameter for nonlinear effects) and K (hydraulic conductivity). Sensitivity analysis shows that in general ?? and V0 have the lowest sensitivity and K usually has the highest. However, for very high K values the sensitivity to A may surpass the sensitivity to K. Oscillatory slug tests involve higher accelerations and velocities of the water column; thus, the pressure transducer responses are affected by these factors and the model response must be corrected to allow maximum accuracy for the analysis. The performance of multiple slug tests will allow some statistical measure of the experimental accuracy and of the reliability of the resulting aquifer parameters. ?? 2002 Elsevier Science B.V. All rights reserved.

Verification of the Multi-Axial, Temperature and Time Dependent (MATT) Failure Criterion

NASA Technical Reports Server (NTRS)

Richardson, David E.; Macon, David J.

2005-01-01

An extensive test and analytical effort has been completed by the Space Shuttle's Reusable Solid Rocket Motor (KSKM) nozzle program to characterize the failure behavior of two epoxy adhesives (TIGA 321 and EA946). As part of this effort, a general failure model, the "Multi-Axial, Temperature, and Time Dependent" or MATT failure criterion was developed. In the initial development of this failure criterion, tests were conducted to provide validation of the theory under a wide range of test conditions. The purpose of this paper is to present additional verification of the MATT failure criterion, under new loading conditions for the adhesives TIGA 321 and EA946. In many cases, the loading conditions involve an extrapolation from the conditions under which the material models were originally developed. Testing was conducted using three loading conditions: multi-axial tension, torsional shear, and non-uniform tension in a bondline condition. Tests were conducted at constant and cyclic loading rates ranging over four orders of magnitude. Tests were conducted under environmental conditions of primary interest to the RSRM program. The temperature range was not extreme, but the loading ranges were extreme (varying by four orders of magnitude). It should be noted that the testing was conducted at temperatures below the glass transition temperature of the TIGA 321 adhesive. However for the EA946, the testing was conducted at temperatures that bracketed the glass transition temperature.

40 CFR 63.9913 - What test methods and other procedures must I use to demonstrate initial compliance with the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... must I use to demonstrate initial compliance with the emission limits for particulate matter and PM10... compliance with the emission limits for particulate matter and PM10? (a) You must conduct each performance... determine compliance with the applicable emission limits for particulate matter in Table 1 to this subpart...

40 CFR 63.9913 - What test methods and other procedures must I use to demonstrate initial compliance with the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... must I use to demonstrate initial compliance with the emission limits for particulate matter and PM10... compliance with the emission limits for particulate matter and PM10? (a) You must conduct each performance... determine compliance with the applicable emission limits for particulate matter in Table 1 to this subpart...

Interdisciplinary Interactions within a Small-Scale Research Initiative Investigating Animation Creation as a Means of Teaching and Learning

ERIC Educational Resources Information Center

Wishart, J. M.; Wakley, G.

2017-01-01

This paper reports an interdisciplinary research (IDR) initiative conducted by two lecturers from different university faculties who found they shared an interest in using animations to support teaching and learning. The research comprised an exploratory pilot to test the feasibility, and to explore the impact on learning, of having undergraduates…

Autonomic changes after treatment of agoraphobia with panic attacks.

PubMed

Roth, W T; Telch, M J; Taylor, C B; Agras, W S

1988-04-01

Twenty-three patients meeting DSM-III criteria for agoraphobia with panic attacks and 14 age-, race-, and sex-matched nonanxious controls were tested in the laboratory and on a test walk in a shopping mall. The patients were tested before and after about 15 weeks of treatment with placebo and exposure therapy, imipramine and exposure therapy, or imipramine and initial antiexposure instructions. Controls were tested twice at a similar interval, but without any treatment. On test day 1, patients compared to controls showed higher average heart rate and skin conductance levels and greater numbers of skin conductance fluctuations in the laboratory, and higher heart rates before and during the test walk. Between pretreatment and posttreatment tests, clinical ratings improved and skin conductance levels decreased in all treatment groups. Heart rate levels in the laboratory, on the other hand, decreased in patients on placebo and rose in patients on imipramine. Thus, imipramine compromises the usefulness of heart rate as a measure of emotional arousal. Higher pretreatment heart rates predicted greater clinical improvement.

Characterization of the Edge Crack Torsion (ECT) Test for Mode III Fracture Toughness Measurement of Laminated Composites

NASA Technical Reports Server (NTRS)

Ratcliffe, James G.

2004-01-01

The edge crack torsion (ECT) test is designed to initiate mode III delamination growth in composite laminates. The test has undergone several design changes during its development. The objective of this paper was to determine the suitability of the current ECT test design a mode III fracture test. To this end, ECT tests were conducted on specimens manufactured from IM7/8552 and S2/8552 tape laminates. Three-dimensional finite element analyses were performed. The analysis results were used to calculate the distribution of mode I, mode II, and mode III strain energy release rate along the delamination front. The results indicated that mode IIIdominated delamination growth would be initiated from the specimen center. However, in specimens of both material types, the measured values of GIIIc exhibited significant dependence on delamination length. Load-displacement response of the specimens exhibited significant deviation from linearity before specimen failure. X-radiographs of a sample of specimens revealed that damage was initiated in the specimens prior to failure. Further inspection of the failure surfaces is required to identify the damage and determine that mode III delamination is initiated in the specimens.

Safety of falciparum malaria diagnostic strategy based on rapid diagnostic tests in returning travellers and migrants: a retrospective study

PubMed Central

2012-01-01

Background Rapid diagnostic tests for malaria (RDTs) allow accurate diagnosis and prompt treatment. Validation of their usefulness in travellers with fever was needed. The safety of a strategy to diagnose falciparum malaria based on RDT followed by immediate or delayed microscopy reading at first attendance was evaluated in one referral hospital in Switzerland. Methods A retrospective study was conducted in the outpatient clinic and emergency ward of University Hospital, covering a period of eight years (1999–2007). The study was conducted in the outpatient clinic and emergency ward of University Hospital. All adults suspected of malaria with a diagnostic test performed were included. RDT and microscopy as immediate tests were performed during working hours, and RDT as immediate test and delayed microscopy reading out of laboratory working hours. The main outcome measure was occurrence of specific complications in RDT negative and RDT positive adults. Results 2,139 patients were recruited. 1987 had both initial RDT and blood smear (BS) result negative. Among those, 2/1987 (0.1%) developed uncomplicated malaria with both RDT and BS positive on day 1 and day 6 respectively. Among the 152 patients initially malaria positive, 137 had both RDT and BS positive, four only BS positive and five only RDT positive (PCR confirmed) (six had only one test performed). None of the four initially RDT negative/BS positive and none of the five initially BS negative/RDT positive developed severe malaria while 6/137 of both RDT and BS positive did so. The use of RDT allowed a reduction of a median of 2.1 hours to get a first malaria test result. Conclusions A malaria diagnostic strategy based on RDTs and a delayed BS is safe in non-immune populations, and shortens the time to first malaria test result. PMID:23158019

An overview of large wind turbine tests by electric utilities

NASA Technical Reports Server (NTRS)

Vachon, W. A.; Schiff, D.

1982-01-01

A summary of recent plants and experiences on current large wind turbine (WT) tests being conducted by electric utilities is provided. The test programs discussed do not include federal research and development (R&D) programs, many of which are also being conducted in conjunction with electric utilities. The information presented is being assembled in a project, funded by the Electric Power Research Institute (EPRI), the objective of which is to provide electric utilities with timely summaries of test performance on key large wind turbines. A summary of key tests, test instrumentation, and recent results and plans is given. During the past year, many of the utility test programs initiated have encountered test difficulties that required specific WT design changes. However, test results to date continue to indicate that long-term machine performance and cost-effectiveness are achievable.

Correlations of microstructure with dynamic and quasi-static fracture in a plain carbon steel

NASA Astrophysics Data System (ADS)

Couque, H.; Asaro, R. J.; Duffy, J.; Lee, S. H.

1988-09-01

An investigation was conducted into the effects of temperature, loading rate, and various micro-structural parameters on the initiation of plane strain fracture of a plain carbon AISI 1020 steel. Ferrite and prior austenite grain sizes were chosen as the principal microstructural features to be in-vestigated. The microstructural variations were accomplished by changing the austenitizing tempera-ture and by altering the cooling rate during normalization. Fracture toughness tests were conducted using precracked notched round bars loaded in tension to produce two stress intensity rates, viz., K 1 = 1 MPa √m s-1 and K 1 = 2 × 106 MPa √m s-1. In addition, Charpy impact tests along with quasistatic and high rate plasticity tests were conducted. The plasticity tests were done in torsion at shear strain rates ofoverline γ = 5.0 × 10^{ - 4} s^{ - 1 } and overline γ = 1.5 × 10^{3 } s^{ - 1} . Testing temperatures covered the range from -150 °C to 150 °C which encompassed fracture initiation modes involving transgranular cleavage to fully ductile fracture. Micromechanical processes involved in void and cleavage micro-crack formation were identified and quantified. For these purposes notched round tensile tests and subsequent metallographic observations along with TEM and SEM observations of the plane strain fracture toughness specimens were performed. The experimental results and quantitative micro-modeling using simple fracture models provide a means of correlating both quasistatic and dynamic fracture toughness with microstructures.

Biometric identification standards research

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Air Quality Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM projects being...

Creep fatigue life prediction for engine hot section materials (isotropic)

NASA Technical Reports Server (NTRS)

Moreno, V.

1983-01-01

The Hot Section Technology (HOST) program, creep fatigue life prediction for engine hot section materials (isotropic), is reviewed. The program is aimed at improving the high temperature crack initiation life prediction technology for gas turbine hot section components. Significant results include: (1) cast B1900 and wrought IN 718 selected as the base and alternative materials respectively; (2) fatigue test specimens indicated that measurable surface cracks appear early in the specimen lives, i.e., 15% of total life at 871 C and 50% of life at 538 c; (3) observed crack initiation sites are all surface initiated and are associated with either grain boundary carbides or local porosity, transgrannular cracking is observed at the initiation site for all conditions tested; and (4) an initial evaluation of two life prediction models, representative of macroscopic (Coffin-Mason) and more microscopic (damage rate) approaches, was conducted using limited data generated at 871 C and 538 C. It is found that the microscopic approach provides a more accurate regression of the data used to determine crack initiation model constants, but overpredicts the effect of strain rate on crack initiation life for the conditions tested.

SNS Cryogenic Test Facility Kinney Vacuum Pump Commissioning and Operation at 2 K

NASA Astrophysics Data System (ADS)

DeGraff, B.; Howell, M.; Kim, S.; Neustadt, T.

2017-12-01

The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory (ORNL) has built and commissioned an independent Cryogenic Test Facility (CTF) in support of testing in the Radio-frequency Test Facility (RFTF). Superconducting Radio-frequency Cavity (SRF) testing was initially conducted with the CTF cold box at 4.5 K. A Kinney vacuum pump skid consisting of a roots blower with a liquid ring backing pump was recently added to the CTF system to provide testing capabilities at 2 K. System design, pump refurbishment and installation of the Kinney pump will be presented. During the commissioning and initial testing period with the Kinney pump, several barriers to achieve reliable operation were experienced. Details of these lessons learned and improvements to skid operations will be presented. Pump capacity data will also be presented.

SNS Cryogenic Test Facility Kinney Vacuum Pump Commissioning and Operation at 2 K

DOE Office of Scientific and Technical Information (OSTI.GOV)

Degraff, Brian D.; Howell, Matthew P.; Kim, Sang-Ho

The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory (ORNL) has built and commissioned an independent Cryogenic Test Facility (CTF) in support of testing in the Radio-frequency Test Facility (RFTF). Superconducting Radio-frequency Cavity (SRF) testing was initially conducted with the CTF cold box at 4.5 K. A Kinney vacuum pump skid consisting of a roots blower with a liquid ring backing pump was recently added to the CTF system to provide testing capabilities at 2 K. System design, pump refurbishment and installation of the Kinney pump will be presented. During the commissioning and initial testing period with the Kinneymore » pump, several barriers to achieve reliable operation were experienced. Details of these lessons learned and improvements to skid operations will be presented. Pump capacity data will also be presented.« less

40 CFR 60.45 - Emissions and fuel monitoring.

Code of Federal Regulations, 2010 CFR

2010-07-01

.../J (0.060 lb/MMBtu) or less and that does not use post-combustion technology to reduce emissions of... initial performance tests under § 60.8 have been conducted. If the owner or operator demonstrates during the performance test that emissions of NOX are less than 70 percent of the applicable standards in...

40 CFR 60.45 - Emissions and fuel monitoring.

Code of Federal Regulations, 2011 CFR

2011-07-01

.../J (0.060 lb/MMBtu) or less and that does not use post-combustion technology to reduce emissions of... initial performance tests under § 60.8 have been conducted. If the owner or operator demonstrates during the performance test that emissions of NOX are less than 70 percent of the applicable standards in...

Integrated Thermal Modules for Cooling Silicon and Silicon Carbide Power Modules

DTIC Science & Technology

2007-06-11

analyses, bench tests, and motor tests comprise the program. The ITMs, in place of standard heatsinks, use a highly conductive pyrolytic graphite to...passively cool power modules. Initial results show that even simple ITMs can lower chip temperatures by 20 deg. C and 10 deg. C with engine oil and

Purging of a tank-mounted multilayer insulation system by gas diffusion

NASA Technical Reports Server (NTRS)

Sumner, I. E.

1978-01-01

The investigation was conducted on a multilayer insulation (MLI) system mounted on a spherical liquid hydrogen propellant tank. The MLI consisted of two blankets of insulation each containing 15 double-aluminized Mylar radiation shields separated by double silk net spacers. The gaseous nitrogen initially contained within the MLI system and vacuum chamber was purged with gaseous helium introduced both underneath the MLI and into the vacuum chamber. The MLI panels were assumed to be purged primarily by means of gas diffusion. Overall, test results indicated that nitrogen concentrations well below 1 percent could be achieved everywhere within the MLI system. Typical times to achieve 1 percent nitrogen concentration within the MLI panels ranged from 69 minutes at the top of the tank to 158 minutes at the bottom of the tank. Four space-hold thermal performance tests indicated no significant thermal degradation of the MLI system had occurred due to the purge tests conducted. The final measured heat input attributed to the MLI was 7.23 watts as compared to 7.18 watts for the initial baseline thermal performance test.

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, Bill Prosser (left) and Eric Madaras, NASA-Langley Research Center, conduct impulse tests on the right wing leading edge (WLE) of Space Shuttle Endeavour. The tests monitor how sound impulses propagate through the WLE area. The data collected will be analyzed to explore the possibility of adding new instrumentation to the wing that could automatically detect debris or micrometeroid impacts on the Shuttle while in flight. The study is part of the initiative ongoing at KSC and around the agency to return the orbiter fleet to flight status.

NASA Image and Video Library

2003-10-27

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, Bill Prosser (left) and Eric Madaras, NASA-Langley Research Center, conduct impulse tests on the right wing leading edge (WLE) of Space Shuttle Endeavour. The tests monitor how sound impulses propagate through the WLE area. The data collected will be analyzed to explore the possibility of adding new instrumentation to the wing that could automatically detect debris or micrometeroid impacts on the Shuttle while in flight. The study is part of the initiative ongoing at KSC and around the agency to return the orbiter fleet to flight status.

Titanium-Oxygen Reactivity Study

NASA Technical Reports Server (NTRS)

Chafey, J. E.; Scheck, W. G.; Witzell, W. E.

1962-01-01

A program has been conducted at Astronautics to investigate the likelihood of occurrence of the catastrophic oxidation of titanium alloy sheet under conditions which simulate certain cases of accidental failure of the metal while it is in contact with liquid or gaseous oxygen. Three methods of fracturing the metal were used; they consisted of mechanical puncture, tensile fracture of welded joints, and perforation by very high velocity particles. The results of the tests which have been conducted provide further evidence of the reactivity of titanium with liquid and gaseous oxygen. The evidence indicates that the rapid fracturing of titanium sheet while it is in contact with oxygen initiates the catastrophic oxidation reaction. Initiation occurred when the speed of the fracture was some few feet per second, as in both the drop-weight puncture tests and the static tensile fracture tests of welded joints, as well as when the speed was several thousand feet per second, as in the simulated micrometeoroid penetration tests. The slow propagation of a crack, however, did not initiate the reaction. It may logically be concluded that the localized frictional heat of rapid fracture and/or spontaneous oxidation (exothermic) of minute particles emanating from the fracture cause initiation of the reaction. Under conditions of slow fracture, however, the small heat generated may be adequately dissipated and the reaction is not initiated. A portion of the study conducted consisted of investigating various means by which the reaction might be retarded or prevented. Providing a "barrier" at the titanium-oxygen interface consisting of either aluminum metal or a coating of a petroleum base corrosion inhibitor appeared to be only partially effective in retarding the reaction. The accidental puncturing or similar rupturing of thin-walled pressurized oxygen tanks on missiles and space vehicle will usually constitute loss of function, and may sometimes cause their catastrophic destruction by explosive decompression regardless of the type of material used for their construction. In the case of tanks constructed of titanium alloys the added risk is incurred of catastrophic burning of the tanks. In view of this it is recommended that thin-walled tanks constructed of titanium alloys should not be used to contain liquid or gaseous oxygen.

From community-based pilot testing to region-wide systems change: lessons from a local quality improvement collaborative.

PubMed

Keyser, Donna J; Pincus, Harold Alan

2010-01-01

A community-based collaborative conducted a 2-year pilot study to inform efforts for improving maternal and child health care practice and policy in Allegheny County, Pennsylvania. (1) To test whether three small-scale versions of an evidence-based, systems improvement approach would be workable in local community settings and (2) to identify specific policy/infrastructure reforms for sustaining improvements. A mixed methods approach was used, including quantitative performance measurement supplemented with qualitative data about factors related to outcomes of interest, as well as key stakeholder interviews and a literature review/Internet search. Quantitative performance results varied; qualitative data revealed critical factors for the success and failure of the practices tested. Policy/infrastructure recommendations were developed to address specific practice barriers. This information was important for designing a region-wide quality improvement initiative focused on maternal depression. The processes and outcomes provide valuable insights for other communities interested in conducting similar quality improvement initiatives.

Association Between Direct-to-Consumer Advertising and Testosterone Testing and Initiation in the United States, 2009–2013

PubMed Central

Layton, J. Bradley; Kim, Yoonsang; Alexander, G. Caleb; Emery, Sherry L.

2017-01-01

IMPORTANCE Testosterone initiation increased substantially in the United States from 2000 to 2013, especially among men without clear indications. Direct-to-consumer advertising (DTCA) also increased during this time. OBJECTIVE To investigate associations between televised DTCA and testosterone testing and initiation in the United States. DESIGN, SETTING, AND POPULATION Ecologic study conducted in designated market areas (DMAs) in the United States. Monthly testosterone advertising ratings were linked to DMA-level testosterone use data from 2009–2013 derived from commercial insurance claims. Associations between DTCA and testosterone testing, initiation, and initiation without recent baseline tests were estimated using Poisson generalized estimating equations. EXPOSURES Monthly Nielsen ratings for testosterone DTCA in the 75 largest DMAs. MAIN OUTCOMES AND MEASURES (1) Rates of new serum testosterone testing; (2) rates of testosterone initiation (in-office injection, surgical implant, or pharmacy dispensing) for all testosterone products combined and for specific brands; and (3) rates of testosterone initiation without recent serum testosterone testing. RESULTS Of 17 228 599 commercially insured men in the 75 DMAs, 1 007 990 (mean age, 49.6 [SD, 11.5] years) had new serum testosterone tests and 283 317 (mean age, 51.8 [SD, 11.3] years) initiated testosterone treatment. Advertising intensity varied by geographic region and time, with the highest intensity seen in the southeastern United States and with months ranging from no ad exposures to a mean of 13.6 exposures per household. Nonbranded advertisements were common prior to 2012, with branded advertisements becoming more common during and after 2012. Each household advertisement exposure was associated with a monthly increase in rates of new testosterone testing (rate ratio [RR], 1.006; 95% CI, 1.004–1.008), initiation (RR, 1.007; 95% CI, 1.004–1.010), and initiation without a recent test (RR, 1.008; 95% CI, 1.002–1.013). Mean absolute rate increases were 0.14 tests (95% CI, 0.09–0.19), 0.05 new initiations (95% CI, 0.03–0.08), and 0.02 initiations without a recent test (95% CI, 0.01–0.03) per 10 000 men for each monthly ad exposure over the entire period. CONCLUSIONS AND RELEVANCE Among US men residing in the 75 designated market areas, regional exposure to televised direct-to-consumer advertising was associated with greater testosterone testing, new initiation, and initiation without recent testing. PMID:28324090

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kashikhin, V.; Cheban, S.; DiMarco, J.

New LCLS-II Linear Superconducting Accelerator Cry-omodules are under construction at Fermilab. Installed in-side each SCRF Cryomodule is a superconducting magnet package to focus and steer an electron beam. The magnet package is an iron dominated configuration with conduc-tively cooled racetrack-type quadrupole and dipole coils. For easier installation the magnet can be split in the vertical plane. Initially the magnet was tested in a liquid helium bath, and high precision magnetic field measurements were performed. The first (prototype) Cryomodule with the magnet inside was built and successfully tested at Fermilab test facility. In this paper the magnet package is discussed, themore » Cryomodule magnet test results and current leads con-duction cooling performance are presented. So far magnets in nine Cryomodules were successfully tested at Fermilab.« less

Summary and evaluation: fuel dynamics loss-of-flow experiments (tests L2, L3, and L4)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barts, E.W.; Deitrich, L.W.; Eberhart, J.G.

1975-09-01

Three similar experiments conducted to support the analyses of hypothetical LMFBR unprotected-loss-of-flow accidents are summarized and evaluated. The tests, designated L2, L3, and L4, provided experimental data against which accident-analysis codes could be compared, so as to guide further analysis and modeling of the initiating phases of the hypothetical accident. The tests were conducted using seven-pin bundles of mixed-oxide fuel pins in Mark-II flowing-sodium loops in the TREAT reactor. Test L2 used fresh fuel. Tests L3 and L4 used irradiated fuel pins having, respectively, ''intermediate-power'' (no central void) and ''high-power'' (fully developed central void) microstructure. 12 references. (auth)

Fatigue, Creep-Fatigue, and Thermomechanical Fatigue Life Testing of Alloys

NASA Technical Reports Server (NTRS)

Halford, Gary R.; Lerch, Bradley A.; McGaw, Michael A.

2000-01-01

The fatigue crack initiation resistance of an alloy is determined by conducting a series of tests over a range of values of stress amplitude or strain range. The observed number of cycles to failure is plotted against the stress amplitude or strain range to obtain a fatigue curve. The fatigue properties quoted for an alloy are typically the constants used in the equation(s) that describe the fatigue curve. Fatigue lives of interest may be as low as 10(exp 2) or higher than 10(exp 9) cycles. Because of the enormous scatter associated with fatigue, dozens of tests may be needed to confidently establish a fatigue curve, and the cost may run into several thousands of dollars. To further establish the effects on fatigue life of the test temperature, environment, alloy condition, mean stress effects, creep-fatigue effects, thermomechanical cycling, etc. requires an extraordinarily large and usually very costly test matrix. The total effort required to establish the fatigue resistance of an alloy should not be taken lightly. Fatigue crack initiation tests are conducted on relatively small and presumed to be initially crack-free, samples of an alloy that are intended to be representative of the alloy's metallurgical and physical condition. Generally, samples are smooth and have uniformly polished surfaces within the test section. Some may have intentionally machined notches of well-controlled geometry, but the surface at the root of the notch is usually not polished. The purpose of polishing is to attain a reproducible surface finish. This is to eliminate surface finish as an uncontrolled variable. Representative test specimen geometries will be discussed later. Test specimens are cyclically loaded until macroscopically observable cracks initiate and eventually grow to failure. Normally, the fatigue failure life of a specimen is defined as the number of cycles to separation of the specimen into two pieces. Alternative definitions are becoming more common, particularly for low-cycle fatigue testing, wherein some prescribed indication of impending failure due to cracking is adopted. Specific criteria will be described later. As a rule, cracks that develop during testing are not measured nor are the test parameters intentionally altered owing to the presence of cracking.

High-Frequency Axial Fatigue Test Procedures for Spectrum Loading

DTIC Science & Technology

2016-07-20

histories can be performed at frequencies much higher than standard servo-hydraulic test frames by using a test frame that is optimized to run at higher...by using a test frame that is optimized to run at higher frequencies. AIR 4.3 has conducted a research program to develop a test capability for...Applied Research (BAR) program (219BAR-10-008) was initiated in 2010. The program investigated the influence of a generic rotorcraft main rotor blade root

Starter/generator testing

NASA Astrophysics Data System (ADS)

Anon

1994-10-01

Sundstrand Aerospace and GE Aircraft Engines have studied the switched reluctance machine for use as an integral starter/generator for future aircraft engines. They have conducted an initial, low-power testing of the starter/generator, which is based on power inverters using IGBT-technology semiconductors, to verify its feasibility in the externally mounted version of the integral starter/generator. This preliminary testing of the 250-kW starter/generator reveals favorable results.

The High Energy Lightning Simulator (HELS) Test Facility for Testing Explosive Items

DTIC Science & Technology

1996-08-01

Center, Redstone Arsenal, AL Thomas E. Roy and David W. Bagwell AMTEC Corporation, Huntsville, AL ABSTRACT Details of the High Energy Lightning...simulated lightning testing of inerted missiles and inerted explosive items containing electrically initiated explosive trains is to determine the...penetrate the safety cages, which are electrically conductive and grounded, without loss of current. This transmission system consists of six large

Unique Challenges to Preventing Perinatal HIV Transmission among Hispanic Women in California: Results of a Needs Assessment

ERIC Educational Resources Information Center

Kropp, Rhonda Y.; Montgomery, Elizabeth T.; Hill, David W.; Ruiz, Juan D.; Maldonado, Yvonne A.

2005-01-01

To identify rates and factors associated with timely prenatal care (PNC) initiation, HIV test counseling, test offering, and test offer acceptance, we conducted a semistructured survey of a convenience sample of pregnant/recently delivered Hispanic women (n = 453, 418 with analyzable data) in four California counties in 2000. Only 68.4% and 43.5%…

Experiment data report for Semiscale Mod-1 Test S-05-1 (alternate ECC injection test)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feldman, E. M.; Patton, Jr., M. L.; Sackett, K. E.

Recorded test data are presented for Test S-05-1 of the Semiscale Mod-1 alternate ECC injection test series. These tests are among several Semiscale Mod-1 experiments conducted to investigate the thermal and hydraulic phenomena accompanying a hypothesized loss-of-coolant accident in a pressurized water reactor (PWR) system. Test S-05-1 was conducted from initial conditions of 2263 psia and 544/sup 0/F to investigate the response of the Semiscale Mod-1 system to a depressurization and reflood transient following a simulated double-ended offset shear of the cold leg broken loop piping. During the test, cooling water was injected into the vessel lower plenum to simulatemore » emergency core coolant injection in a PWR, with the flow rate based on system volume scaling.« less

Evaluation of new aquatic toxicity test methods for oil dispersants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pace, C.B.; Clark, J.R.; Bragin, G.E.

1994-12-31

Current aquatic toxicity test methods used for dispersant registration do not address real world exposure scenarios. Current test methods require 48 or 96 hour constant exposure conditions. In contrast, environmentally realistic exposures can be described as a pulse in which the initial concentration declines over time. Recent research using a specially designed testing apparatus (the California system) has demonstrated that exposure to Corexit 9527{reg_sign} under pulsed exposure conditions may be 3 to 22 times less toxic compared to continuous exposure scenarios. The objectives of this study were to compare results of toxicity tests using the California test system to resultsmore » from standardized tests, evaluate sensitivity of regional (Holmesimysis cast and Atherinops affinis) vs. standard test species (Mysidopsis bahia and Menidia beryllina) and determine if tests using the California test system and method are reproducible. All tests were conducted using Corexit 9527{reg_sign} as the test material. Standard toxicity tests conducted with M. bahia and H. cast resulted in LC50s similar to those from tests using the California apparatus. LC50s from tests conducted in the authors` laboratory with the California system and standard test species were within a factor of 2 to 6 of data previously reported for west coast species. Results of tests conducted with H. cast in the laboratory compared favorably to data reported by Singer et al. 1991.« less

A nonlinear model for analysis of slug-test data

USGS Publications Warehouse

McElwee, C.D.; Zenner, M.A.

1998-01-01

While doing slug tests in high-permeability aquifers, we have consistently seen deviations from the expected response of linear theoretical models. Normalized curves do not coincide for various initial heads, as would be predicted by linear theories, and are shifted to larger times for higher initial heads. We have developed a general nonlinear model based on the Navier-Stokes equation, nonlinear frictional loss, non-Darcian flow, acceleration effects, radius changes in the well bore, and a Hvorslev model for the aquifer, which explains these data features. The model produces a very good fit for both oscillatory and nonoscillatory field data, using a single set of physical parameters to predict the field data for various initial displacements at a given well. This is in contrast to linear models which have a systematic lack of fit and indicate that hydraulic conductivity varies with the initial displacement. We recommend multiple slug tests with a considerable variation in initial head displacement to evaluate the possible presence of nonlinear effects. Our conclusion is that the nonlinear model presented here is an excellent tool to analyze slug tests, covering the range from the underdamped region to the overdamped region.

Use of Strain Measurements from Acoustic Bench Tests of the Battleship Flowliner Test Articles To Link Analytical Model Results to In-Service Resonant Response

NASA Technical Reports Server (NTRS)

Frady, Greg; Smaolloey, Kurt; LaVerde, Bruce; Bishop, Jim

2004-01-01

The paper will discuss practical and analytical findings of a test program conducted to assist engineers in determining which analytical strain fields are most appropriate to describe the crack initiating and crack propagating stresses in thin walled cylindrical hardware that serves as part of the Space Shuttle Main Engine's fuel system. In service the hardware is excited by fluctuating dynamic pressures in a cryogenic fuel that arise from turbulent flow/pump cavitation. A bench test using a simplified system was conducted using acoustic energy in air to excite the test articles. Strain measurements were used to reveal response characteristics of two Flowliner test articles that are assembled as a pair when installed in the engine feed system.

Simulation of Fatigue Crack Initiation at Corrosion Pits With EDM Notches

NASA Technical Reports Server (NTRS)

Smith, Stephen W.; Newman, John A.; Piascik, Robert S.

2003-01-01

Uniaxial fatigue tests were conducted to compare the fatigue life of laboratory produced corrosion pits, similar to those observed in the shuttle main landing gear wheel bolt-hole, and an electro-discharged-machined (EDM) flaw. EDM Jaws are used to simulate corrosion pits during shuttle wheel (dynamometer) testing. The aluminum alloy, (AA 7050) laboratory fatigue tests were conducted to simulate the local stress level contained in the wheel bolt-hole. Under this high local stress condition, the EDM notch produced a fatigue life similar to test specimens containing corrosion pits of similar size. Based on the laboratory fatigue test results, the EDM Jaw (semi-circular disc shaped) produces a local stress state similar to corrosion pits and can be used to simulate a corrosion pit during the shuttle wheel dynamometer tests.

40 CFR 63.7941 - How do I conduct a performance test, design evaluation, or other type of initial compliance...

Code of Federal Regulations, 2011 CFR

2011-07-01

... evaluation, you must collect the appropriate operating parameter monitoring system data, average the... 760 °C or higher. (f) You must conduct a performance evaluation for each continuous monitoring system... Level 1 controls, § 63.1063(d) for Tank Level 2 controls, § 63.926(a) for Container Level 1 controls...

40 CFR 63.7941 - How do I conduct a performance test, design evaluation, or other type of initial compliance...

Code of Federal Regulations, 2013 CFR

2013-07-01

... evaluation, you must collect the appropriate operating parameter monitoring system data, average the... 760 °C or higher. (f) You must conduct a performance evaluation for each continuous monitoring system... Level 1 controls, § 63.1063(d) for Tank Level 2 controls, § 63.926(a) for Container Level 1 controls...

40 CFR 63.7941 - How do I conduct a performance test, design evaluation, or other type of initial compliance...

Code of Federal Regulations, 2012 CFR

2012-07-01

... evaluation, you must collect the appropriate operating parameter monitoring system data, average the... 760 °C or higher. (f) You must conduct a performance evaluation for each continuous monitoring system... Level 1 controls, § 63.1063(d) for Tank Level 2 controls, § 63.926(a) for Container Level 1 controls...

Initial Simulations of RF Waves in Hot Plasmas Using the FullWave Code

NASA Astrophysics Data System (ADS)

Zhao, Liangji; Svidzinski, Vladimir; Spencer, Andrew; Kim, Jin-Soo

2017-10-01

FullWave is a simulation tool that models RF fields in hot inhomogeneous magnetized plasmas. The wave equations with linearized hot plasma dielectric response are solved in configuration space on adaptive cloud of computational points. The nonlocal hot plasma dielectric response is formulated by calculating the plasma conductivity kernel based on the solution of the linearized Vlasov equation in inhomogeneous magnetic field. In an rf field, the hot plasma dielectric response is limited to the distance of a few particles' Larmor radii, near the magnetic field line passing through the test point. The localization of the hot plasma dielectric response results in a sparse matrix of the problem thus significantly reduces the size of the problem and makes the simulations faster. We will present the initial results of modeling of rf waves using the Fullwave code, including calculation of nonlocal conductivity kernel in 2D Tokamak geometry; the interpolation of conductivity kernel from test points to adaptive cloud of computational points; and the results of self-consistent simulations of 2D rf fields using calculated hot plasma conductivity kernel in a tokamak plasma with reduced parameters. Work supported by the US DOE ``SBIR program.

Effect of initial delamination on Mode 1 and Mode 2 interlaminar fracture toughness and fatigue fracture threshold

NASA Technical Reports Server (NTRS)

Murri, Gretchen Bostaph; Martin, Roderick H.

1991-01-01

Static and fatigue double-cantilever beam (DCB) and end-notch flexure (ENF) tests were conducted to determine the effect of the simulated initial delamination in interlaminar fracture toughness, G(sub c), and fatigue fracture threshold, G(sub th). Unidirectional, 24-ply specimens of S2/SP250 glass/epoxy were tested using Kapton inserts of four different thickness - 13, 25, 75, and 130 microns, at the midplane at one end, or with tension or shear precracks, to simulate an initial delamination. To determine G(sub c), the fatigue fracture threshold below which no delamination growth would occur in less than 1 x 10(exp 6) cycles, fatigue tests were conducted by cyclically loading specimens until delamination growth was detected. Consistent values of model 1 fracture toughness, G(sub Ic), were measured from DCB specimens with inserts of thickness 75 microns or thinner, or with shear precracks. The fatigue DCB tests gave similar values of G(sub Ith) for the 13, 25, and 75 microns specimens. Results for the shear precracked specimens were significantly lower that for specimens without precracks. Results for both the static and fatigue ENF tests showed that measured G(IIc) and G(IIth) values decreased with decreasing insert thickness, so that no limiting thickness could be determined. Results for specimens with inserts of 75 microns or thicker were significantly higher than the results for precracked specimens or specimens with 13 or 25 microns inserts.

Comparison of the inertial properties and forces required to initiate movement for three gait trainers.

PubMed

Paleg, Ginny; Huang, Morris; Vasquez Gabela, Stephanie C; Sprigle, Stephen; Livingstone, Roslyn

2016-01-01

The purpose of this study was to evaluate the inertial properties and forces required to initiate movement on two different surfaces in a sample of three commonly prescribed gait trainers. Tests were conducted in a laboratory setting to compare the Prime Engineering KidWalk, Rifton Pacer, and Snug Seat Mustang with and without a weighted anthropometric test dummy configured to the weight and proportions of a 4-year-old child. The Pacer was the lightest and the KidWalk the heaviest while footprints of the three gait trainers were similar. Weight was borne fairly evenly on the four casters of the Pacer and Mustang while 85% of the weight was borne on the large wheels of the mid-wheel drive KidWalk. These differences in frame style, wheel, and caster style and overall mass impact inertial properties and forces required to initiate movement. Test results suggest that initiation forces on tile were equivalent for the Pacer and KidWalk while the Mustang had the highest initiation force. Initiation forces on carpet were lowest for the KidWalk and highest for the Mustang. This initial study of inertia and movement initiation forces may provide added information for clinicians to consider when selecting a gait trainer for their clients.

Pretest analysis document for Test S-FS-6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaw, R.A.; Hall, D.G.

This report documents the pretest analyses completed for Semiscale Test S-FS-6. This test will simulate a transient initiated by a 100% break in a steam generator bottom feedwater line downstream of the check valve. The initial conditions represent normal operating conditions for a C-E System 80 nuclear power plant. Predictions of transients resulting from feedwater line breaks in these plants have indicated that significant primary system overpressurization may occur. The enclosed analyses include a RELAP5/MOD2/CY21 code calculation and preliminary results from a facility hot, integrated test which was conducted to near S-FS-6 specifications. The results of these analyses indicate thatmore » the test objectives for Test S-FS-6 can be achieved. The primary system overpressurization will pose no threat to personnel or plant integrity.« less

Plasma Discharge Initiation of Explosives in Rock Blasting Application: A Case Study

NASA Astrophysics Data System (ADS)

Jae-Ou, Chae; Young-Jun, Jeong; V, M. Shmelev; A, A. Denicaev; V, M. Poutchkov; V, Ravi

2006-07-01

A plasma discharge initiation system for the explosive volumetric combustion charge was designed, investigated and developed for practical application. Laboratory scale experiments were carried out before conducting the large scale field tests. The resultant explosions gave rise to less noise, insignificant seismic vibrations and good specific explosive consumption for rock blasting. Importantly, the technique was found to be safe and environmentally friendly.

Long life nickel electrodes for a nickel-hydrogen cell. I Initial performance

NASA Technical Reports Server (NTRS)

Lim, H. S.; Verzwyvelt, S. A.; Blaser, C.; Keener, K. M.

1983-01-01

In order to develop a long life nickel electrode for a Ni/H2 cell, an investigation was begun to study the effects of sinter structure and active material loading level on the long life performance of nickel electrodes. This paper is a report on the initial performance of these electrodes as a part of an accelerated life test program. Seven different types of nickel plaques were made which included three levels of both their mechanical strength and median pore size. These plaques were impregnated with three levels of active material loading. The resultant electrodes were tested by a 200-cycle stress test which was conducted in flooded electrolyte, and also for initial performance in a Ni/H2 boiler plate cell. An interesting and unexpected observation was that an increased initial utilization of the active material was due more to its complete discharge to the lower average oxidation state than its increased charge acceptance in the charged state.

Exploring the cause of initially reactive bovine brains on rapid tests for BSE

PubMed Central

Dudas, Sandor; James, Jace; Anderson, Renee; Czub, Stefanie

2015-01-01

ABSTRACT Bovine spongiform encephalopathy (BSE) is an invariably fatal prion disease of cattle. The identification of the zoonotic potential of BSE prompted safety officials to initiate surveillance testing for this disease. In Canada, BSE surveillance is primarily focused on high risk cattle including animals which are dead, down and unable to rise, diseased or distressed. This targeted surveillance results in the submission of brain samples with a wide range of tissue autolysis and associated contaminants. These contaminants have the potential to interfere with important steps of surveillance tests resulting in initially positive test results requiring additional testing to confirm the disease status of the animal. The current tests used for BSE screening in Canada utilize the relative protease resistance of the prion protein gained when it misfolds from PrPC to PrPSc as part of the disease process. Proteinase K completely digests PrPC in normal brains, but leaves most of the PrPSc in BSE positive brains intact which is detected using anti-prion antibodies. These tests are highly reliable but occasionally give rise to initially reactive/false positive results. Test results for these reactive samples were close to the positive/negative cut-off on a sub set of test platforms. This is in contrast to all of the previous Canadian positive samples whose numeric values on these same test platforms were 10 to 100 fold greater than the test positive/negative cut-off. Here we explore the potential reason why a sample is repeatedly positive on a sub-set of rapid surveillance tests, but negative on other test platforms. In order to better understand and identify what might cause these initial reactions, we have conducted a variety of rapid and confirmatory assays as well as bacterial isolation and identification on BSE positive, negative and initially reactive samples. We observed high levels of viable bacterial contamination in initially reactive samples suggesting that the reactivity may be related to bacterial factors. Several bacteria isolated from the initially reactive samples have characteristics of biofilm forming bacteria and this extracellular matrix might play a role in preventing complete digestion of PrPC in these samples. PMID:26689488

National evaluation of the SafeTrip-21 initiative I-95 corridor coalition test bed : final evaluation report, providing multi-modal travel information to airport users.

DOT National Transportation Integrated Search

2011-12-30

The purpose of this document is to present the findings of the national evaluation of the I-95 Corridor Coalitions Airport Ground Transport Travel Information project, one element of the I-95 Test Bed conducted under the USDOTs SafeTrip-21 Init...

40 CFR 63.1349 - Performance testing requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) THC emissions test. (i) If you are subject to limitations on THC emissions, you must operate a CEMS in... assurance evaluations for CEMS, the THC span value (as propane) is 50 ppmvd and the reference method (RM) is Method 25A of appendix A to part 60 of this chapter. (ii) Use the THC CEMS to conduct the initial...

40 CFR 63.7732 - What test methods and other procedures must I use to demonstrate initial compliance with the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... emissions limitations? (a) You must conduct each performance test that applies to your iron and steel...) Method 18 to determine the VOHAP concentration. Alternatively, you may use Method 25 to determine the... of total hydrocarbons (as hexane) for 180 continuous operating minutes. You must measure emissions at...

Heating of food in modified atmospheres

NASA Technical Reports Server (NTRS)

Sweat, V. E.

1973-01-01

Food heating tests were conducted with two model foods; a Carnation turkey salad sandwich spread and frankfurter chunks in a sauce of water and agar. For the first series of tests comparing heating in five different atmospheres, the atmospheres were: (1) air at atmospheric pressure, (2) air at 5 psia, (3) helium at 5 psia, (4) oxygen-nitrogen mixture at 5 psia, and (5) oxygen-helium mixture at 5 psia. No significant differences in heating rates were caused by varying the atmosphere. Initial food temperatures were varied in the next series of tests. Heating times were found to increase with decreasing initial temperatures. There were also differences in heating times between the two foods used.

Interventions to improve or facilitate linkage to or retention in pre-ART (HIV) care and initiation of ART in low- and middle-income settings – a systematic review

PubMed Central

Govindasamy, Darshini; Meghij, Jamilah; Negussi, Eyerusalem Kebede; Baggaley, Rachel Clare; Ford, Nathan; Kranzer, Katharina

2014-01-01

Introduction Several approaches have been taken to reduce pre-antiretroviral therapy (ART) losses between HIV testing and ART initiation in low- and middle-income countries, but a systematic assessment of the evidence has not yet been undertaken. The aim of this systematic review is to assess the potential for interventions to improve or facilitate linkage to or retention in pre-ART care and initiation of ART in low- and middle-income settings. Methods An electronic search was conducted on Medline, Embase, Global Health, Web of Science and conference databases to identify studies describing interventions aimed at improving linkage to or retention in pre-ART care or initiation of ART. Additional searches were conducted to identify on-going trials on this topic, and experts in the field were contacted. An assessment of the risk of bias was conducted. Interventions were categorized according to key domains in the existing literature. Results A total of 11,129 potentially relevant citations were identified, of which 24 were eligible for inclusion, with the majority (n=21) from sub-Saharan Africa. In addition, 15 on-going trials were identified. The most common interventions described under key domains included: health system interventions (i.e. integration in the setting of antenatal care); patient convenience and accessibility (i.e. point-of-care CD4 count (POC) testing with immediate results, home-based ART initiation); behaviour interventions and peer support (i.e. improved communication, patient referral and education) and incentives (i.e. food support). Several interventions showed favourable outcomes: integration of care and peer supporters increased enrolment into HIV care, medical incentives increased pre-ART retention, POC CD4 testing and food incentives increased completion of ART eligibility screening and ART initiation. Most studies focused on the general adult patient population or pregnant women. The majority of published studies were observational cohort studies, subject to an unclear risk of bias. Conclusions Findings suggest that streamlining services to minimize patient visits, providing adequate medical and peer support, and providing incentives may decrease attrition, but the quality of the current evidence base is low. Few studies have investigated combined interventions, or assessed the impact of interventions across the HIV cascade. Results from on-going trials investigating POC CD4 count testing, patient navigation, rapid ART initiation and mobile phone technology may fill the quality of evidence gap. Further high-quality studies on key population groups are required, with interventions informed by previously reported barriers to care. PMID:25095831

Life prediction and constitutive models for engine hot section anisotropic materials

NASA Technical Reports Server (NTRS)

Swanson, G. A.; Linask, I.; Nissley, D. M.; Norris, P. P.; Meyer, T. G.; Walker, K. P.

1987-01-01

The results are presented of a program designed to develop life prediction and constitutive models for two coated single crystal alloys used in gas turbine airfoils. The two alloys are PWA 1480 and Alloy 185. The two oxidation resistant coatings are PWA 273, an aluminide coating, and PWA 286, an overlay NiCoCrAlY coating. To obtain constitutive and fatigue data, tests were conducted on uncoated and coated specimens loaded in the CH76 100 CH110 , CH76 110 CH110 , CH76 111 CH110 and CH76 123 CH110 crystallographic directions. Two constitutive models are being developed and evaluated for the single crystal materials: a micromechanic model based on crystallographic slip systems, and a macroscopic model which employs anisotropic tensors to model inelastic deformation anisotropy. Based on tests conducted on the overlay coating material, constitutive models for coatings also appear feasible and two initial models were selected. A life prediction approach was proposed for coated single crystal materials, including crack initiation either in the coating or in the substrate. The coating initiated failures dominated in the tests at load levels typical of gas turbine operation. Coating life was related to coating stress/strain history which was determined from specimen data using the constitutive models.

Regional Traffic Incident Management Programs : Implementation Guide

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Air Quality Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM projects ...

Traffic conflict techniques for safety and operations : observers manual

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Institutional and Organizational Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. T...

Nuclear Magnetic Resonance Trackbed Moisture Sensor System

DOT National Transportation Integrated Search

2018-02-01

In this initial phase, conducted from March 2015 through December 2016, Vista Clara and its subcontractor Zetica Rail successfully developed and tested a man-portable, non-invasive spot-check nuclear magnetic resonance (NMR) moisture sensor that dire...

Northern Shenandoah Valley ITS -- public safety initiative : final report

DOT National Transportation Integrated Search

2002-01-23

This report summarizes the efforts of The Pennsylvania State Universitys Applied Research Laboratory (PSU/ARL) to conduct field tests using a handheld data collection system to enable emergency medical personnel (EMS) to collect and transfer patie...

An Engineering Methodology for Implementing and Testing VLSI (Very Large Scale Integrated) Circuits

DTIC Science & Technology

1989-03-01

the pad frame and associated routing, conducted additional testing. and submitted the finished design effort to MOSIS for manufacturing. Throughout...register bank TSTCON Allows the XNOR circuitry to enter the TEST register bank PADIN Test signal to check operation of the input pad VCC Power connection...MOSSIM II simulation program. but the design offered little observability within the circuit. The initial design used 35 pins of a 40 pin pad frame

Crack Initiation and Growth Behavior at Corrosion Pit in 7075-T6 Under Biaxial and Uniaxial Fatigue

DTIC Science & Technology

2014-06-19

al. examined the effect of biaxial loading on the fatigue crack growth [52]. They conducted their fatigue tests on SUS 304 stainless steel using a...specimens. Their experiments were carried out on cruciform test coupons using a digitally controlled four actuator biaxial testing system. Steel ...as shown in Figure 3.7. The test specimen was placed between two stainless steel chambers. These chambers were connected together using screws, and

Dry and wet arc track propagation resistance testing

NASA Technical Reports Server (NTRS)

Beach, Rex

1995-01-01

The wet arc-propagation resistance test for wire insulation provides an assessment of the ability of an insulation to prevent damage in an electrical environment. Results of an arc-propagation test may vary slightly due to the method of arc initiation; therefore a standard test method must be selected to evaluate the general arc-propagation resistance characteristics of an insulation. This test method initiates an arc by dripping salt water over pre-damaged wires which creates a conductive path between the wires. The power supply, test current, circuit resistances, and other variables are optimized for testing 20 guage wires. The use of other wire sizes may require modifications to the test variables. The dry arc-propagation resistance test for wire insulation also provides an assessment of the ability of an insulation to prevent damage in an electrical arc environment. In service, electrical arcs may originate form a variety of factors including insulation deterioration, faulty installation, and chafing. Here too, a standard test method must be selected to evaluate the general arc-propagation resistance characteristics of an insulation. This test method initiates an arc with a vibrating blade. The test also evaluates the ability of the insulation to prevent further arc-propagation when the electrical arc is re-energized.

Study for fabrication, evaluation, and testing of monolayer woven type materials for space suit insulation

NASA Technical Reports Server (NTRS)

Merrick, E. B.

1979-01-01

An alternative space suit insulation concept using a monolayer woven pile material is discussed. The material reduces cost and improves the durability of the overgarment, while providing protection similar to that provided by multilayer insulation (MLI). Twelve samples of different configurations were fabricated and tested for compressibility and thermal conductivity as a function of compression loading. Two samples which showed good results in the initial tests were further tested for thermal conductivity with respect to ambient pressure and temperature. Results of these tests were similar to results of the MLI tests, indicating the potential of the monolayer fabric to replace the present MLI. A seaming study illustrated that the fabric can be sewn in a structurally sound seam with minimal heat loss. It is recommended that a prototype thermal meteroid garment be fabricated.

Promoting learning, memory, and transfer in a time-constrained, high hazard environment.

PubMed

Molesworth, Brett R C; Bennett, Lauren; Kehoe, E James

2011-05-01

Two methods of metacognitive reflection for promoting compliance with an aviation safety rule were tested in a transfer design. Two groups of pilots (n = 10) conducted a simulated flight entailing a search for a target on the ground. During this flight, only 35% of the pilots stayed above an altitude of 500 ft, the minimum allowed by relevant regulations. Following the flight, one group completed a self-explanation questionnaire, in which they explained their actions during the initial flight and what they would do in future flights. The other group completed a relapse-prevention questionnaire, in which they identified the circumstances leading to safety lapses and their future avoidance. A third group (n = 10) formed a rest control; they conducted a familiarization flight without a ground target or debriefing. One week later, all pilots conducted a series of test flights with the same or different ground targets as the initial flight. The self-explanation group showed 100% compliance when the ground target remained the same, but less so (<70%) when the ground target was different. The relapse-prevention group and control groups both showed low levels of compliance across all test flights (<30%). The results are discussed from theoretical and applied perspectives. Copyright © 2010 Elsevier Ltd. All rights reserved.

Reflections of a Wave: An Analysis of Photonic Doppler Velocimetry Systems

DTIC Science & Technology

2015-03-16

system employed by the Advanced Initiation Sciences team, (Munitions Direc - torate, AFRL) is capable of explosive sensitivity testing. The errors from...1961, experiments proved that Semenov Theory aligned well with well- stirred liquids [25, p. 179]. In combat applications, the military usually utilizes...solid explosives instead of liquid ones due to the higher stability of solid-molded explosives where conduction has a huge influence on initiation

40 CFR 63.6611 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2011 CFR

2011-07-01

... reconstructed 4SLB SI stationary RICE with a site rating of greater than or equal to 250 and less than or equal... compliance demonstrations if I own or operate a new or reconstructed 4SLB SI stationary RICE with a site... of HAP emissions? If you own or operate a new or reconstructed 4SLB stationary RICE with a site...

Response of advance reproduction of oaks and associated species to repeated prescribed fires in upland oak-hickory forests, Missouri

Treesearch

Zhaofei Fan; Zhongqiu Ma; Daniel C. Dey; Scott D. Roberts

2012-01-01

The Chilton Creek prescribed burn project was initiated in 1996 by The Nature Conservancy (TNC) to restore native oak woodlands and test the effect of frequent, low intensity surface fires conducted in the dormant season (March-April) on upland oak-hickory forests in the Ozarks of Missouri. Burning treatments on five sites totaling 1000 ha were initiated in 1998. The...

Hydrogen peroxide-enhanced iron-mediated aeration for the treatment of mature landfill leachate.

PubMed

Deng, Yang; Englehardt, James D

2008-05-01

Municipal landfill leachate is being disallowed for biological treatment by some sewer authorities due to its recalcitrance and corrosiveness, and therefore physicochemical treatment may be needed. In this paper, hydrogen peroxide-enhanced iron (Fe(0))-mediated aeration (IMA) was studied as an alternative for the treatment of mature landfill leachate. Bench-scale Taguchi array screening tests and full factorial tests were conducted. Iron grade, initial pH, H(2)O(2) addition rate, and aeration rate significantly influenced both overall chemical oxygen demand (COD) removal and iron consumption. In the enhanced IMA-treated leachate at an initial pH of 8.2, COD was reduced by 50% due to oxidation and coagulation, a level almost equivalent to those obtained by Fenton treatment. Meanwhile, the 5-day biochemical oxygen demand (BOD(5))/COD ratio was increased from 0.02 to 0.17. In particular, the effect of initial pH became minor at H(2)O(2) addition rate greater than the theoretical demand for complete oxidation of organics by H(2)O(2). In addition, 83% of 300 mg/L ammonia nitrogen and 38% of 8.30 mS/cm electrical conductivity were removed when the initial pH was not adjusted. Based on these results, the process appears suitable for treatment of mature leachate.

Sensitivity and Validity of Psychometric Tests for Assessing Driving Impairment: Effects of Sleep Deprivation

PubMed Central

Jongen, Stefan; Perrier, Joy; Vuurman, Eric F.; Ramaekers, Johannes G.; Vermeeren, Annemiek

2015-01-01

Objective To assess drug induced driving impairment, initial screening is needed. However, no consensus has been reached about which initial screening tools have to be used. The present study aims to determine the ability of a battery of psychometric tests to detect performance impairing effects of clinically relevant levels of drowsiness as induced by one night of sleep deprivation. Methods Twenty four healthy volunteers participated in a 2-period crossover study in which the highway driving test was conducted twice: once after normal sleep and once after one night of sleep deprivation. The psychometric tests were conducted on 4 occasions: once after normal sleep (at 11 am) and three times during a single night of sleep deprivation (at 1 am, 5 am, and 11 am). Results On-the-road driving performance was significantly impaired after sleep deprivation, as measured by an increase in Standard Deviation of Lateral Position (SDLP) of 3.1 cm compared to performance after a normal night of sleep. At 5 am, performance in most psychometric tests showed significant impairment. As expected, largest effect sizes were found on performance in the Psychomotor Vigilance Test (PVT). Large effects sizes were also found in the Divided Attention Test (DAT), the Attention Network Test (ANT), and the test for Useful Field of View (UFOV) at 5 and 11 am during sleep deprivation. Effects of sleep deprivation on SDLP correlated significantly with performance changes in the PVT and the DAT, but not with performance changes in the UFOV. Conclusion From the psychometric tests used in this study, the PVT and DAT seem most promising for initial evaluation of drug impairment based on sensitivity and correlations with driving impairment. Further studies are needed to assess the sensitivity and validity of these psychometric tests after benchmark sedative drug use. PMID:25668292

Performance oriented guidance for Mississippi chip seals - volume II.

DOT National Transportation Integrated Search

2013-12-01

A laboratory and field study was conducted related to long term chip seal performance. This reports primary : objective was to initiate development of a long term performance (LTP) test protocol for chip seals focused on : aggregate retention. Key...

Development of the North American cargo securement standard

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Benefit-Cost Analysis (BCA) for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM pr...

Advanced Gas Turbine (AGT) powertrain system development for automotive applications

NASA Technical Reports Server (NTRS)

1984-01-01

Rotor dynamic instability investigations were conducted. Forward ball bearing hydraulic mount configurations were tested with little effect. Trial assembly of S/N 002 ceramic engine was initiated. Impeller design activities were completed on the straight line element (SLE) blade definition to address near-net-shape powder metal die forging. Performance characteristics of the Baseline Test 2A impeller were closely preserved. The modified blading design has been released for tooling procurement. Developmental testing of the diffusion flame combustor (DFC) for initial use in the S/N 002 2100 F ceramic structures engine was completed. A natural gas slave preheater was designed and fabricated. Preliminary regenerator static seal rig testing showed a significant reduction in leakage and sensitivity to stack height. Ceramic screening tests were completed and two complete sets of ceramic static structures were qualified for engine testing. Efforts on rotor dynamics development to resolve subsynchronous motion were continued.

40 CFR 63.6630 - How do I demonstrate initial compliance with the emission limitations, operating limitations, and...

Code of Federal Regulations, 2013 CFR

2013-07-01

... formaldehyde emission limit by testing for THC instead of formaldehyde. The testing must be conducted according to the requirements in Table 4 of this subpart. The average reduction of emissions of THC determined... subpart, or using appendix A to this subpart. (4) If you are demonstrating compliance with the THC percent...

40 CFR 63.6630 - How do I demonstrate initial compliance with the emission limitations, operating limitations, and...

Code of Federal Regulations, 2014 CFR

2014-07-01

... formaldehyde emission limit by testing for THC instead of formaldehyde. The testing must be conducted according to the requirements in Table 4 of this subpart. The average reduction of emissions of THC determined... subpart, or using appendix A to this subpart. (4) If you are demonstrating compliance with the THC percent...

40 CFR 60.45 - Emissions and fuel monitoring.

Code of Federal Regulations, 2014 CFR

2014-07-01

... oil) with potential SO2 emissions rates of 26 ng/J (0.060 lb/MMBtu) or less and that does not use post... of a CEMS for NOX may be delayed until after the initial performance tests under § 60.8 have been conducted. If the owner or operator demonstrates during the performance test that emissions of NOX are less...

40 CFR 60.45 - Emissions and fuel monitoring.

Code of Federal Regulations, 2013 CFR

2013-07-01

... oil) with potential SO2 emissions rates of 26 ng/J (0.060 lb/MMBtu) or less and that does not use post... of a CEMS for NOX may be delayed until after the initial performance tests under § 60.8 have been conducted. If the owner or operator demonstrates during the performance test that emissions of NOX are less...

40 CFR 60.45 - Emissions and fuel monitoring.

Code of Federal Regulations, 2012 CFR

2012-07-01

... oil) with potential SO2 emissions rates of 26 ng/J (0.060 lb/MMBtu) or less and that does not use post... of a CEMS for NOX may be delayed until after the initial performance tests under § 60.8 have been conducted. If the owner or operator demonstrates during the performance test that emissions of NOX are less...

Preferred Information Platforms for Parents Choosing to Refuse Mandatory PARCC Testing in a Southern New Jersey School District

ERIC Educational Resources Information Center

Benson, Lauren

2017-01-01

This executive position paper identifies preferred modes of communication for parents and guardians in a small New Jersey Public School District. Research was conducted because there has been an unprecedented test refusal initiative by parents and guardians of New Jersey Public School Students who are mandated to sit for Partnership for Assessment…

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, Eric Madaras (left), NASA-Langley Research Center, and Jim McGee, The Boeing Company, Huntington Beach, Calif., conduct impulse tests on the right wing leading edge (WLE) of Space Shuttle Endeavour. The tests monitor how sound impulses propagate through the WLE area. The data collected will be analyzed to explore the possibility of adding new instrumentation to the wing that could automatically detect debris or micrometeroid impacts on the Shuttle while in flight. The study is part of the initiative ongoing at KSC and around the agency to return the orbiter fleet to flight status.

NASA Image and Video Library

2003-10-27

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, Eric Madaras (left), NASA-Langley Research Center, and Jim McGee, The Boeing Company, Huntington Beach, Calif., conduct impulse tests on the right wing leading edge (WLE) of Space Shuttle Endeavour. The tests monitor how sound impulses propagate through the WLE area. The data collected will be analyzed to explore the possibility of adding new instrumentation to the wing that could automatically detect debris or micrometeroid impacts on the Shuttle while in flight. The study is part of the initiative ongoing at KSC and around the agency to return the orbiter fleet to flight status.

AJ26 engine test

NASA Image and Video Library

2011-03-19

A team of engineers from NASA's John C. Stennis Space Center, Orbital Sciences Corporation and Aerojet conduct a successful test of an Aerojet AJ26 rocket engine on March 19. Stennis is testing AJ26 engines for Orbital Sciences to power commercial cargo missions to the International Space Station. Orbital has partnered with NASA through the Commercial Orbital Transportation Services initiative to carry out eight cargo missions to the space station by 2015, using Taurus II rockets.

Viscoelastic Properties of Advanced Polymer Composites for Ballistic Protective Applications

DTIC Science & Technology

1994-09-01

ofthe Damaged Sample 78 Figure 69: Fracture Surface of Damage Area Near the Point of Penetration 79 Figure 70. Closer View ofthe Damaged Area...LIST OF TABLES Table 1. Basic Mechanical Properties of the Materials 6 Table 2. Initial DMA Test Results 23 Table 3. Flexural Three Point Bend... point bend testing was conducted using an Instron 1127 Universal Tester to verify the DMA test method and specimen clamping configuration. Interfacial

Geotechnical properties of municipal solid waste at different phases of biodegradation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reddy, Krishna R., E-mail: kreddy@uic.edu; Hettiarachchi, Hiroshan, E-mail: hiroshan@ltu.edu; Gangathulasi, Janardhanan, E-mail: jganga2@uic.edu

Highlights: > Degraded synthetic municipal solid waste (MSW) anaerobically in controlled bench-scale reactors. > Performed laboratory tests to determine geotechnical properties of MSW at different phases of degradation. > Hydraulic conductivity decreased by two orders of magnitude due to degradation. > Compression ratio reduced from 0.34 for initial fresh waste to 0.15 for the mostly degraded waste. > Friction angle reduced, but cohesion increased with degradation. - Abstract: This paper presents the results of laboratory investigation conducted to determine the variation of geotechnical properties of synthetic municipal solid waste (MSW) at different phases of degradation. Synthetic MSW samples were preparedmore » based on the composition of MSW generated in the United States and were degraded in bioreactors with leachate recirculation. Degradation of the synthetic MSW was quantified based on the gas composition and organic content, and the samples exhumed from the bioreactor cells at different phases of degradation were tested for the geotechnical properties. Hydraulic conductivity, compressibility and shear strength of initial and degraded synthetic MSW were all determined at constant initial moisture content of 50% on wet weight basis. Hydraulic conductivity of synthetic MSW was reduced by two orders of magnitude due to degradation. Compression ratio was reduced from 0.34 for initial fresh waste to 0.15 for the mostly degraded waste. Direct shear tests showed that the fresh and degraded synthetic MSW exhibited continuous strength gain with increase in horizontal deformation, with the cohesion increased from 1 kPa for fresh MSW to 16-40 kPa for degraded MSW and the friction angle decreased from 35{sup o} for fresh MSW to 28{sup o} for degraded MSW. During the triaxial tests under CU condition, the total strength parameters, cohesion and friction angle, were found to vary from 21 to 57 kPa and 1{sup o} to 9{sup o}, respectively, while the effective strength parameters, cohesion and friction angle varied from 18 to 56 kPa and from 1{sup o} to 11{sup o}, respectively. Similar to direct shear test results, as the waste degrades an increase in cohesion and slight decrease in friction angle was observed. Decreased friction angle and increased cohesion with increased degradation is believed to be due to the highly cohesive nature of the synthetic MSW. Variation of synthetic MSW properties from this study also suggests that significant changes in geotechnical properties of MSW can occur due to enhanced degradation induced by leachate recirculation.« less

Dried Blood Spot Test for HIV Exposed Infants and Children and Their Anti-Retro Viral Treatment Status in Selected Hospitals in Ethiopia.

PubMed

Wondafrash, Beyene; Hiko, Desta

2016-01-01

Infants and children living with HIV receive antiretroviral treatment often late, are exposed to opportunistic infection and quickly develop AIDS. Few hospitals are providing ART service after Dried Blood Spot (DBS)test.The objective of this study is to assess the status of infants and children linked to ART. Descriptive cross-sectional study was conducted in hospitals. Data of 138 infants and children exposed to HIV were collected from registration books and data bases from 2009 to 2011. Data were analyzed using SPSS version 16. Chi-squared test and p-value were computed. In-depth interviews were conducted with key informants. Ninety-eight (71%) infants and children exposed to HIV were diagnosed for HIV infection of which 68(69.4%) initiated ART. Twenty four (35.3%) initiated ART one month after HIV screening results. Thirty-three (50.0%) and 23(35.3%) infants and children dropped from and adhered to ART respectively. Eleven (16.2%) of them who initiated ART died within the study period. HIV infection status (p-value=0.003), dropping from ART (p-value=0.002) and death after ART initiation (p-value=0.010) showed significance with mothers' PMTCT service status. Seven in ten HIV-exposed infants and children were diagnosed with HIV, and almost all of them initiated ART. The overall turnaround time was 10 days. Based up on mothers' PMTCT service status, there was a significant difference among HIV-exposed infants and children in acquiring HIV infection from mothers during pregnancy (p-value=0.003) and dropping from ART (p-value=0.010). There were challenges in sample collection and transportation. Early HIV screening during pregnancy and PMTCT service should be strengthened.

Microstructural characterization of hydrogen induced cracking in TRIP-assisted steel by EBSD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laureys, A., E-mail: Aurelie.Laureys@UGent.be; Depover, T.; Petrov, R.

2016-02-15

The present work evaluates hydrogen induced cracking by performing an elaborate EBSD (Electron BackScatter Diffraction) study in a steel with transformation induced plasticity (TRIP-assisted steel). This type of steel exhibits a multiphase microstructure which undergoes a deformation induced phase transformation. Additionally, each microstructural constituent displays a different behavior in the presence of hydrogen. The aim of this study is to obtain a better understanding on the mechanisms governing hydrogen induced crack initiation and propagation in the hydrogen saturated multiphase structure. Tensile tests on notched samples combined with in-situ electrochemical hydrogen charging were conducted. The tests were interrupted at stresses justmore » after reaching the tensile strength, i.e. before macroscopic failure of the material. This allowed to study hydrogen induced crack initiation and propagation by SEM (Scanning Electron Microscopy) and EBSD. A correlation was found between the presence of martensite, which is known to be very susceptible to hydrogen embrittlement, and the initiation of hydrogen induced cracks. Initiation seems to occur mostly by martensite decohesion. High strain regions surrounding the hydrogen induced crack tips indicate that further crack propagation may have occurred by the HELP (hydrogen-enhanced localized plasticity) mechanism. Small hydrogen induced cracks located nearby the notch are typically S-shaped and crack propagation was dominantly transgranularly. The second stage of crack propagation consists of stepwise cracking by coalescence of small hydrogen induced cracks. - Highlights: • Hydrogen induced cracking in TRIP-assisted steel is evaluated by EBSD. • Tensile tests were conducted on notched hydrogen saturated samples. • Crack initiation occurs by a H-Enhanced Interface DEcohesion (HEIDE) mechanism. • Crack propagation involves growth and coalescence of small cracks. • Propagation is governed by the characteristics of phases on the crack path.« less

Evaluation program for secondary spacecraft cells: Initial evaluation tests of Gulton Industries, Incorporated, 9.0 ampere-hour nickel-cadmium spacecraft cells with auxiliary electrodes for the small astronomy Satellite (SAS-C)

NASA Technical Reports Server (NTRS)

Harkness, J. D.

1975-01-01

An evaluation test program was conducted to insure that all cells put into the life cycle program are of high quality by the screening of cells found to have electrolyte leakage, internal shorts, low capacity, or inability of any cell to recover its open-circuit voltage above 1.150 volts during the internal short test. Tests and results are described.

A cold ejector for closed-cycle helium refrigerators

NASA Technical Reports Server (NTRS)

Johnson, D. L.; Daggett, D. L.

1987-01-01

The test results are presented of an initial cold helium ejector design that can be installed on a closed cycle refrigerator to provide refrigeration at temperatures below 4.2 K. The ejector, test apparatus, instrumentation, and test results are described. Tests were conducted both at room temperature and at cryogenic temperatures to provide operational experience with the ejector as well as for future use in the subsequent design of an ejector that will provide refrigeration at temperatures below 3 K.

Performance characteristics of an electric vehicle lead-acid battery pack at elevated temperatures

NASA Technical Reports Server (NTRS)

Chapman, P.

1982-01-01

Discharge testing data electric car battery pack over initial electrolyte temperature variations between 27 and 55 C are presented. The tests were conducted under laboratory conditions and then compared to detailed electric vehicle simulation models. Battery discharge capacity increased with temperature for constant current discharges, and battery energy capacity increased with temperature for constant power discharges. Dynamometer tests of the electric test vehicle showed an increase in range of 25% for the higher electrolyte temperature.

Optimizing Infant HIV Diagnosis in Resource-Limited Settings: Modeling the Impact of HIV DNA PCR Testing at Birth.

PubMed

Chiu, Alexander; Modi, Surbhi; Rivadeneira, Emilia D; Koumans, Emilia H

2016-12-01

Early antiretroviral therapy (ART) initiation in HIV-infected infants significantly improves survival but is often delayed in resource-limited settings. Adding HIV testing of infants at birth to the current recommendation of testing at age 4-6 weeks may improve testing rates and decrease time to ART initiation. We modeled the benefit of adding HIV testing at birth to the current 6-week testing algorithm. Microsoft Excel was used to create a decision-tree model of the care continuum for the estimated 1,400,000 HIV-infected women and their infants in sub-Saharan Africa in 2012. The model assumed average published rates for facility births (42.9%), prevention of mother-to-child HIV transmission utilization (63%), mother-to-child-transmission rates based on prevention of mother-to-child HIV transmission regimen (5%-40%), return of test results (41%), enrollment in HIV care (52%), and ART initiation (54%). We conducted sensitivity analyses to model the impact of key variables and applied the model to specific country examples. Adding HIV testing at birth would increase the number of infants on ART by 204% by age 18 months. The greatest increase is seen in early ART initiations (543% by age 3 months). The increase would lead to a corresponding increase in survival at 12 months of age, with 5108 fewer infant deaths (44,550, versus 49,658). Adding HIV testing at birth has the potential to improve the number and timing of ART initiation of HIV-infected infants, leading to a decrease in infant mortality. Using this model, countries should investigate a combination of HIV testing at birth and during the early infant period.

SPERT I DESTRUCTIVE TEST PROGRAM SAFETY ANALYSIS REPORT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spano, A.H.; Miller, R.W.

1962-06-15

The water-moderated core used for destructive experiments is mounted in the Spent I open-type reactor vessel, which has no provision for pressurization or forced coolant flow. The core is an array of highly enriched aluminum clad, plate-type fuel assemblies, using four bladetype, gang-operated control rods. Reactor transients are initiated at ambient temperature by step-insentions of reactivity, using a control rod which can be quickly ejected from the core. Following an initial series of static measurements to determine the basic- reactor properties of the test core, a series of nondestructive, self-limiting power excursion tests was performed, which covered a reactor periodmore » range down to the point where minor fuel plate damage first occurred -approximately for a 10- msec period test. These tests provided power, temperature, and pressure data. Additional kinetic teste in the period region between 10 and 5 msec were completed to explore the region of limited core damage. Fuel plate damage results included plate distortion, cladding cracking, and fuel melting. These exploratory tests were valuable in revealing unexpected changes in the dependence of pressure, temperature, burst energy, and burst shape parameters on reactor period, although the dependence of peak power on reactor period was not significantly changed. An evaluation of hazards involved in conducting the 2- msec test, based on pessimistic assumptions regarding fission product release and weather conditions, indicates that with the procedural controls normally exercised in the conduct of any transient test at Spent and the special controls to be in effect during the destructive test series, no significant hazard to personnel or to the general public will be obtained. All nuclear operation is conducted remotely approximately 1/2 mile from the reactor building. Discussion is also given of the supervision and control of personnel during and after each destructive test, and of the plans for re-entry, cleanup, and restoration of the facility. (auth)« less

Initial studies of a flexural member composed of glass-fiber reinforced polyester resin.

DOT National Transportation Integrated Search

1973-01-01

An investigation was conducted of the structural behavior of a flexural member composed entirely of glass-fiber reinforced polyester resin. Three experimental girders were fabricated and load-tested in the laboratory. The physical characteristics of ...

40 CFR 60.2125 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2011 CFR

2011-07-01

... the concentration of each dioxin/furan tetra-through octa-chlorinated isomer emitted using EPA Method 23 at 40 CFR part 60, appendix A-7. (2) For each dioxin/furan (tetra-through octa-chlorinated) isomer...

Short-crack growth behaviour in an aluminum alloy: An AGARD cooperative test program

NASA Technical Reports Server (NTRS)

Newman, J. C., Jr.; Edwards, P. R.

1988-01-01

An AGARD Cooperative Test Program on the growth of short fatigue cracks was conducted to define the significance of the short-crack effect, to compare test results from various laboratories, and to evaluate an existing analytical crack-growth prediction model. The initiation and growth of short fatigue cracks (5 micrometer to 2 mm) from the surface of a semi-circular notch in 2024-T3 aluminum alloy sheet material were monitored under various load histories. The cracks initiated from inclusion particle clusters or voids on the notch surface and generally grew as surface cracks. Tests were conducted under several constant-amplitude (stress ratios of -2, -1, 0, and 0.5) and spectrum (FALSTAFF and Gaussian) loading conditions at 3 stress levels each. Short crack growth was recorded using a plastic-replica technique. Over 250 edge-notched specimens were fatigue tested and nearly 950 cracks monitored by 12 participants from 9 countries. Long crack-growth rate data for cracks greater than 2 mm in length were obtained over a wide range in rates (10 to the -8 to 10 to the -1 mm/cycle) for all constant-amplitude loading conditions. Long crack-growth rate data for the FALSTAFF and Gaussian load sequences were also obtained.

Development of a National Campaign Addressing South African Men's Fears About HIV Counseling and Testing and Antiretroviral Treatment

PubMed Central

Orr, Neil; Myers, Laura; Makhubele, Mzamani Benjamin; Matekane, Tselisehang; Delate, Richard; Mahlasela, Lusanda; Goldblatt, Brenda

2017-01-01

Introduction: South African men are less likely to get tested for HIV than women and are more likely to commence antiretroviral treatment (ART) at later stages of disease, default on treatment, and to die from AIDS compared with women. The purpose of this study was to conduct formative research into the ideational and behavioral factors that enable or create obstacles to mens' uptake of HIV counseling and testing (HCT) and ART. The study consulted men with a goal of developing a communication campaign aimed at improving the uptake of HIV testing and ART initiation among men. Methods: Eleven focus groups and 9 in-depth interviews were conducted with 97 male participants in 6 priority districts in 4 South African provinces in rural, peri-urban, and urban localities. Results: Fears of compromised masculine pride and reputation, potential community rejection, and fear of loss of emotional control (“the stress of knowing”) dominated men's rationales for avoiding HIV testing and treatment initiation. Conclusions: A communication campaign was developed based on the findings. Creative treatments aimed at redefining a ‘strong’ man as someone who faces his fears and knows his HIV status. The resultant campaign concept was: “positive or negative—you are still the same person.” PMID:27930614

A Survey of College Reading Programs in New York State, Part II: Diagnosis, Placement and Program Components.

ERIC Educational Resources Information Center

Malinowski, Patricia A.

During spring 1988, an initial survey was conducted among two- and four-year colleges in New York State to identify the primary reading test used for diagnosis and placement. In order to address several questions raised by the study, a follow-up survey of participating two-year colleges was conducted during fall 1989. Of the 28 two-year colleges…

Analytical Prediction of the Seismic Response of a Reinforced Concrete Containment Vessel

DOE Office of Scientific and Technical Information (OSTI.GOV)

James, R.J.; Rashid, Y.R.; Cherry, J.L.

Under the sponsorship of the Ministry of International Trade and Industry (MITI) of Japan, the Nuclear Power Engineering Corporation (NUPEC) is investigating the seismic behavior of a Reinforced Concrete Containment Vessel (RCCV) through scale-model testing using the high-performance shaking table at the Tadotsu Engineering Laboratory. A series of tests representing design-level seismic ground motions was initially conducted to gather valuable experimental measurements for use in design verification. Additional tests will be conducted with increasing amplifications of the seismic input until a structural failure of the test model occurs. In a cooperative program with NUPEC, the US Nuclear Regulatory Commission (USNRC),more » through Sandia National Laboratories (SNL), is conducting analytical research on the seismic behavior of RCCV structures. As part of this program, pretest analytical predictions of the model tests are being performed. The dynamic time-history analysis utilizes a highly detailed concrete constitutive model applied to a three-dimensional finite element representation of the test structure. This paper describes the details of the analysis model and provides analysis results.« less

Evaluation Of Risk And Possible Mitigation Schemes For Previously Unidentified Hazards

NASA Technical Reports Server (NTRS)

Linzey, William; McCutchan, Micah; Traskos, Michael; Gilbrech, Richard; Cherney, Robert; Slenski, George; Thomas, Walter, III

2006-01-01

This report presents the results of arc track testing conducted to determine if such a transfer of power to un-energized wires is possible and/or likely during an arcing event, and to evaluate an array of protection schemes that may significantly reduce the possibility of such a transfer. The results of these experiments may be useful for determining the level of protection necessary to guard against spurious voltage and current being applied to safety critical circuits. It was not the purpose of these experiments to determine the probability of the initiation of an arc track event only if an initiation did occur could it cause the undesired event: an inadvertent thruster firing. The primary wire insulation used in the Orbiter is aromatic polyimide, or Kapton , a construction known to arc track under certain conditions [3]. Previous Boeing testing has shown that arc tracks can initiate in aromatic polyimide insulated 28 volts direct current (VDC) power circuits using more realistic techniques such as chafing with an aluminum blade (simulating the corner of an avionics box or lip of a wire tray), or vibration of an aluminum plate against a wire bundle [4]. Therefore, an arc initiation technique was chosen that provided a reliable and consistent technique of starting the arc and not a realistic simulation of a scenario on the vehicle. Once an arc is initiated, the current, power and propagation characteristics of the arc depend on the power source, wire gauge and insulation type, circuit protection and series resistance rather than type of initiation. The initiation method employed for these tests was applying an oil and graphite mixture to the ends of a powered twisted pair wire. The flight configuration of the heater circuits, the fuel/oxider (or ox) wire, and the RCS jet solenoid were modeled in the test configuration so that the behavior of these components during an arcing event could be studied. To determine if coil activation would occur with various protection wire schemes, 145 tests were conducted using various fuel/ox wire alternatives (shielded and unshielded) and/or different combinations of polytetrafuloroethylene (PTFE), Mystik tape and convoluted wraps to prevent unwanted coil activation. Test results were evaluated along with other pertinent data and information to develop a mitigation strategy for an inadvertent RCS firing. The SSP evaluated civilian aircraft wiring failures to search for aging trends in assessing the wire-short hazard. Appendix 2 applies Weibull statistical methods to the same data with a similar purpose.

Investigation of heat transfer in zirconium potassium perchlorate at low temperature: A study of the failure mechanism of the NASA standard initiator

NASA Technical Reports Server (NTRS)

Varghese, Philip L.

1989-01-01

The objective of this work was to study the reasons for the failure of pyrotechnic initiators at very low temperatures (10 to 100 K). A two-dimensional model of the NASA standard initiator was constructed to model heat transfer from the electrically heated stainless steel bridgewire to the zirconium potassium perchlorate explosive charge and the alumina charge cup. Temperature dependent properties were used in the model to simulate initiator performance over a wide range of initial temperatures (10 to 500 K). A search of the thermophysical property data base showed that pure alumina has a very high thermal conductivity at low temperatures. It had been assumed to act as a thermal insulator in all previous analyses. Rapid heat transfer from the bridgewire to the alumina at low initial temperatures was shown to cause failure of the initiators if the wire did not also make good contact with the zirconium potassium perchlorate charge. The mode is able to reproduce the results of the tests that had been conducted to investigate the cause for failure. It also provides an explanation for previously puzzling results and suggests simple design changes that will increase reliability at very low initial temperatures.

6DOF Testing of the SLS Inertial Navigation Unit

NASA Technical Reports Server (NTRS)

Geohagan, Kevin; Bernard, Bill; Oliver, T. Emerson; Leggett, Jared; Strickland, Dennis

2018-01-01

The Navigation System on the NASA Space Launch System (SLS) Block 1 vehicle performs initial alignment of the Inertial Navigation System (INS) navigation frame through gyrocompass alignment (GCA). Because the navigation architecture for the SLS Block 1 vehicle is a purely inertial system, the accuracy of the achieved orbit relative to mission requirements is very sensitive to initial alignment accuracy. The assessment of this sensitivity and many others via simulation is a part of the SLS Model-Based Design and Model-Based Requirements approach. As a part of the aforementioned, 6DOF Monte Carlo simulation is used in large part to develop and demonstrate verification of program requirements. To facilitate this and the GN&C flight software design process, an SLS-Program-controlled Design Math Model (DMM) of the SLS INS was developed by the SLS Navigation Team. The SLS INS model implements all of the key functions of the hardware-namely, GCA, inertial navigation, and FDIR (Fault Detection, Isolation, and Recovery)-in support of SLS GN&C design requirements verification. Despite the strong sensitivity to initial alignment, GCA accuracy requirements were not verified by test due to program cost and schedule constraints. Instead, the system relies upon assessments performed using the SLS INS model. In order to verify SLS program requirements by analysis, the SLS INS model is verified and validated against flight hardware. In lieu of direct testing of GCA accuracy in support of requirement verification, the SLS Navigation Team proposed and conducted an engineering test to, among other things, validate the GCA performance and overall behavior of the SLS INS model through comparison with test data. This paper will detail dynamic hardware testing of the SLS INS, conducted by the SLS Navigation Team at Marshall Space Flight Center's 6DOF Table Facility, in support of GCA performance characterization and INS model validation. A 6-DOF motion platform was used to produce 6DOF pad twist and sway dynamics while a simulated SLS flight computer communicated with the INS. Tests conducted include an evaluation of GCA algorithm robustness to increasingly dynamic pad environments, an examination of GCA algorithm stability and accuracy over long durations, and a long-duration static test to gather enough data for Allan Variance analysis. Test setup, execution, and data analysis will be discussed, including analysis performed in support of SLS INS model validation.

A Study on the Mechanical Properties and Impact-Induced Initiation Characteristics of Brittle PTFE/Al/W Reactive Materials.

PubMed

Ge, Chao; Maimaitituersun, Wubuliaisan; Dong, Yongxiang; Tian, Chao

2017-04-26

Polytetrafluoroethylene/aluminum/tungsten (PTFE/Al/W) reactive materials of three different component mass ratios (73.5/26.5/0, 68.8/24.2/7 and 63.6/22.4/14) were studied in this research. Different from the PTFE/Al/W composites published elsewhere, the materials in our research were fabricated under a much lower sintering temperature and for a much shorter duration to achieve a brittle property, which aims to provide more sufficient energy release upon impact. Quasi-static compression tests, dynamic compression tests at room and elevated temperatures, and drop weight tests were conducted to evaluate the mechanical and impact-induced initiation characteristics of the materials. The materials before and after compression tests were observed by a scanning electron microscope to relate the mesoscale structural characteristics to their macro properties. All the three types of materials fail at very low strains during both quasi-static and dynamic compression. The stress-strain curves for quasi-static tests show obvious deviations while that for the dynamic tests consist of only linear-elastic and failure stages typically. The materials were also found to exhibit thermal softening at elevated temperatures and were strain-rate sensitive during dynamic tests, which were compared using dynamic increase factors (DIFs). Drop-weight test results show that the impact-initiation sensitivity increases with the increase of W content due to the brittle mechanical property. The high-speed video sequences and recovered sample residues of the drop-weight tests show that the reaction is initiated at two opposite positions near the edges of the samples, where the shear force concentrates the most intensively, indicating a shear-induced initiation mechanism.

A Study on the Mechanical Properties and Impact-Induced Initiation Characteristics of Brittle PTFE/Al/W Reactive Materials

PubMed Central

Ge, Chao; Maimaitituersun, Wubuliaisan; Dong, Yongxiang; Tian, Chao

2017-01-01

Polytetrafluoroethylene/aluminum/tungsten (PTFE/Al/W) reactive materials of three different component mass ratios (73.5/26.5/0, 68.8/24.2/7 and 63.6/22.4/14) were studied in this research. Different from the PTFE/Al/W composites published elsewhere, the materials in our research were fabricated under a much lower sintering temperature and for a much shorter duration to achieve a brittle property, which aims to provide more sufficient energy release upon impact. Quasi-static compression tests, dynamic compression tests at room and elevated temperatures, and drop weight tests were conducted to evaluate the mechanical and impact-induced initiation characteristics of the materials. The materials before and after compression tests were observed by a scanning electron microscope to relate the mesoscale structural characteristics to their macro properties. All the three types of materials fail at very low strains during both quasi-static and dynamic compression. The stress-strain curves for quasi-static tests show obvious deviations while that for the dynamic tests consist of only linear-elastic and failure stages typically. The materials were also found to exhibit thermal softening at elevated temperatures and were strain-rate sensitive during dynamic tests, which were compared using dynamic increase factors (DIFs). Drop-weight test results show that the impact-initiation sensitivity increases with the increase of W content due to the brittle mechanical property. The high-speed video sequences and recovered sample residues of the drop-weight tests show that the reaction is initiated at two opposite positions near the edges of the samples, where the shear force concentrates the most intensively, indicating a shear-induced initiation mechanism. PMID:28772812

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D. H.; Reigel, M. M.

A full-scale formed core sampler was designed and functionally tested for use in the Saltstone Disposal Facility (SDF). Savannah River National Laboratory (SRNL) was requested to compare properties of the formed core samples and core drilled samples taken from adjacent areas in the full-scale sampler. While several physical properties were evaluated, the primary property of interest was hydraulic conductivity. Differences in hydraulic conductivity between the samples from the formed core sampler and those representing the bulk material were noted with respect to the initial handling and storage of the samples. Due to testing conditions, the site port samples were exposedmore » to uncontrolled temperature and humidity conditions prior to testing whereas the formed core samples were kept in sealed containers with minimal exposure to an uncontrolled environment prior to testing. Based on the results of the testing, no significant differences in porosity or density were found between the formed core samples and those representing the bulk material in the test stand.« less

Automated Tow Placement Processing and Characterization of Composites

NASA Technical Reports Server (NTRS)

Prabhakaran, R.

2004-01-01

The project had one of the initial objectives as automated tow placement (ATP), in which a robot was used to place a collimated band of pre-impregnated ribbons or a wide preconsolidated tape onto a tool surface. It was proposed to utilize the Automated Tow Placement machine that was already available and to fabricate carbon fiber reinforced PEEK (polyether-ether-ketone) matrix composites. After initial experiments with the fabrication of flat plates, composite cylinders were to be fabricated. Specimens from the fabricated parts were to be tested for mechanical characterization. A second objective was to conduct various types of tests for characterizing composite specimens cured by different fabrication processes.

Analog Design for Digital Deployment of a Serious Leadership Game

NASA Technical Reports Server (NTRS)

Maxwell, Nicholas; Lang, Tristan; Herman, Jeffrey L.; Phares, Richard

2012-01-01

This paper presents the design, development, and user testing of a leadership development simulation. The authors share lessons learned from using a design process for a board game to allow for quick and inexpensive revision cycles during the development of a serious leadership development game. The goal of this leadership simulation is to accelerate the development of leadership capacity in high-potential mid-level managers (GS-15 level) in a federal government agency. Simulation design included a mixed-method needs analysis, using both quantitative and qualitative approaches to determine organizational leadership needs. Eight design iterations were conducted, including three user testing phases. Three re-design iterations followed initial development, enabling game testing as part of comprehensive instructional events. Subsequent design, development and testing processes targeted digital application to a computer- and tablet-based environment. Recommendations include pros and cons of development and learner testing of an initial analog simulation prior to full digital simulation development.

Development of a Micro-Fiber Nickel Electrode for Nickel-Hydrogen Cell

NASA Technical Reports Server (NTRS)

Britton, Doris L.

1996-01-01

The development of a high specific energy battery is one of the objectives of the lightweight nickel-hydrogen (NiH2) program at the NASA Lewis Research Center. The approach has been to improve the nickel electrode by continuing combined in-house and contract efforts to develop a more efficient and lighter weight electrode for the nickel-hydrogen fuel cell. Small fiber diameter nickel plaques are used as conductive supports for the nickel hydroxide active material. These plaques are commercial products and have an advantage of increased surface area available for the deposition of active materials. Initial tests include activation and capacity measurements at different discharge levels followed by half-cell cycle testing at 80 percent depth-of-discharge in a low Earth orbit regime. The electrodes that pass the initial tests are life cycle tested in a boiler plate nickel-hydrogen cell before flightweight designs are built and tested.

Development of a micro-fiber nickel electrode for nickel-hydrogen cell

NASA Technical Reports Server (NTRS)

Britton, Doris L.

1995-01-01

Development of a high specific energy nickel electrode is the main goal of the lightweight nickel electrode program at the NASA Lewis Research Center. The approach has been to improve the nickel electrode by continuing combined in-house and contract efforts to develop a more efficient and lighter weight electrode for the nickel-hydrogen cell. Small fiber diameter nickel plaques are used as conductive supports for the nickel hydroxide active material. These plaques are commercial products and have an advantage of increased surface area available for the deposition of active material. Initial tests include activation and capacity measurements at different discharge levels followed by half-cell cycle testing at 80 percent depth-of-discharge in a low-Earth-orbit regime. The electrodes that pass the initial tests are life cycle-tested in a boiler plate nickel-hydrogen cell before flightweight designs are built and tested.

Application of a nonlinear slug test model

USGS Publications Warehouse

McElwee, C.D.

2001-01-01

Knowledge of the hydraulic conductivity distribution is of utmost importance in understanding the dynamics of an aquifer and in planning the consequences of any action taken upon that aquifer. Slug tests have been used extensively to measure hydraulic conductivity in the last 50 years since Hvorslev's (1951) work. A general nonlinear model based on the Navier-Stokes equation, nonlinear frictional loss, non-Darcian flow, acceleration effects, radius changes in the wellbore, and a Hvorslev model for the aquifer has been implemented in this work. The nonlinear model has three parameters: ??, which is related primarily to radius changes in the water column; A, which is related to the nonlinear head losses; and K, the hydraulic conductivity. An additional parameter has been added representing the initial velocity of the water column at slug initiation and is incorporated into an analytical solution to generate the first time step before a sequential numerical solution generates the remainder of the time solution. Corrections are made to the model output for acceleration before it is compared to the experimental data. Sensitivity analysis and least squares fitting are used to estimate the aquifer parameters and produce some diagnostic results, which indicate the accuracy of the fit. Finally, an example of field data has been presented to illustrate the application of the model to data sets that exhibit nonlinear behavior. Multiple slug tests should be taken at a given location to test for nonlinear effects and to determine repeatability.

Ground testing on the nonvented fill method of orbital propellant transfer: Results of initial test series

NASA Technical Reports Server (NTRS)

Chato, David J.

1991-01-01

The results are presented of a series of no-vent fill experiments conducted on a 175 cu ft flightweight hydrogen tank. The experiments consisted of the nonvented fill of the tankage with liquid hydrogen using two different inlet systems (top spray, and bottom spray) at different tank initial conditions and inflow rates. Nine tests were completed of which six filled in excess of 94 percent. The experiments demonstrated a consistent and repeatable ability to fill the tank in excess of 94 percent using the nonvented fill technique. Ninety-four percent was established as the high level cutoff due to requirements for some tank ullage to prevent rapid tank pressure rise which occurs in a tank filled entirely with liquid. The best fill was terminated at 94 percent full with a tank internal pressure less than 26 psia. Although the baseline initial tank wall temperature criteria was that all portions of the tank wall be less than 40 R, fills were achieved with initial wall temperatures as high as 227 R.

6DOF Testing of the SLS Inertial Navigation Unit

NASA Technical Reports Server (NTRS)

Geohagan, Kevin W.; Bernard, William P.; Oliver, T. Emerson; Strickland, Dennis J.; Leggett, Jared O.

2018-01-01

The Navigation System on the NASA Space Launch System (SLS) Block 1 vehicle performs initial alignment of the Inertial Navigation System (INS) navigation frame through gyrocompass alignment (GCA). In lieu of direct testing of GCA accuracy in support of requirement verification, the SLS Navigation Team proposed and conducted an engineering test to, among other things, validate the GCA performance and overall behavior of the SLS INS model through comparison with test data. This paper will detail dynamic hardware testing of the SLS INS, conducted by the SLS Navigation Team at Marshall Space Flight Center's 6DOF Table Facility, in support of GCA performance characterization and INS model validation. A 6-DOF motion platform was used to produce 6DOF pad twist and sway dynamics while a simulated SLS flight computer communicated with the INS. Tests conducted include an evaluation of GCA algorithm robustness to increasingly dynamic pad environments, an examination of GCA algorithm stability and accuracy over long durations, and a long-duration static test to gather enough data for Allan Variance analysis. Test setup, execution, and data analysis will be discussed, including analysis performed in support of SLS INS model validation.

A new practice environment measure based on the reality and experiences of nurses working lives.

PubMed

Webster, Joan; Flint, Anndrea; Courtney, Mary

2009-01-01

To explore the underlying organizational issues affecting a nurses' decision to leave and to develop a contemporary practice environment measure based on the experiences of nurses working lives. Turnover had reached an unacceptable level in our organization but underlying reasons for leaving were unknown. In-depth interviews were conducted with 13 nurses who had resigned. Transcripts were analysed using the constant comparative method. Information from the interviews informed the development a new practice environment tool, which has undergone initial testing using the Content Validity Index and Chronbach's alpha. Two domains ('work life' and 'personal life/professional development') and five themes ('feeling safe', 'feeling valued', 'getting things done', 'professional development' and 'being flexible') emerged from the interviews. A content validity score for the new instrument was 0.79 and Chronbach's alpha 0.93. The new practice environment tool has shown useful initial reliability and validity but requires wider testing in other settings. The reality and experiences of nurses working lives can be identified through exit interviews conducted by an independent person. Information from such interviews is useful in identifying an organization's strength and weaknesses and to develop initiatives to support retention.

Incident Management : Successful Practices : A Cross-Cutting Study : Improving Mobility And Saving Lives

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Traveler Response Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM pro...

Impact of local/short haul operations on driver fatigue : focus group summary and analysis

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Institutional and Organizational Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstrati...

The Marshall Space Flight Center KC-135 zero gravity test program for FY 1982

NASA Technical Reports Server (NTRS)

Shurney, R. E. (Editor)

1983-01-01

During FY-82, researchers and experimenters from Marshall Space Flight Center (MSFC) conducted 11 separate investigations during 26.3 hr of testing aboard the KC-135 zero-gravity aircraft, based at Ellington Air force Base, Texas. Although this represented fewer hours than initially projected, all experiment and test objectives were met or exceeded. This Technical Memorandum compiles all results achieved by MSFC users during FY-82, a year considered to be highly productive.

Upgrade of Irradiation Test Capability of the Experimental Fast Reactor Joyo

NASA Astrophysics Data System (ADS)

Sekine, Takashi; Aoyama, Takafumi; Suzuki, Soju; Yamashita, Yoshioki

2003-06-01

The JOYO MK-II core was operated from 1983 to 2000 as fast neutron irradiation bed. In order to meet various requirements for irradiation tests for development of FBRs, the JOYO upgrading project named MK-III program was initiated. The irradiation capability in the MK-III core will be about four times larger than that of the MK-II core. Advanced irradiation test subassemblies such as capsule type subassembly and on-line instrumentation rig are planned. As an innovative reactor safety system, the irradiation test of Self-Actuated Shutdown System (SASS) will be conducted. In order to improve the accuracy of neutron fluence, the core management code system was upgraded, and the Monte Carlo code and Helium Accumulation Fluence Monitor (HAFM) were applied. The MK-III core is planned to achieve initial criticality in July 2003.

Initial flight test of a Loran-C receiver/data collection system

NASA Technical Reports Server (NTRS)

Fischer, J. P.; Nickum, J. D.

1978-01-01

Development of a low cost Loran C receiver for general aviation use is discussed. The preparation and procedure of a flight test conducted with a receiver design which utilizes a phase locked loop oscillator to track the Loran C signals is described. It is indicated that such a receiver is a viable alternative for future work in developing a low cost Loran-C navigator.

Environmental Assessment/Overseas Environmental Assessment for the F-35 Joint Strike Fighter Initial Operational Test and Evaluation

DTIC Science & Technology

2009-09-01

NAS Lemoore; Yolk Field ANGB; Alpena 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF 18. NUMBER 19a. NAME OF RESPONSIBLE PERSON a. REPORT...Currently identified preferred locations for conducting deployment demonstrations are Alpena Combat Readiness Training Center (CRTC), Michigan; Edwards...3-5 3.1.3 Deployment Demonstration Locations .............................................................3-5 3.1.3.1 Alpena Combat Range Test

Summaries of Research; Fiscal Year 1987.

DTIC Science & Technology

1988-02-01

field dentistry . PERSONNEL As of 30 September 1987, there were billets for 8 commissioned officers and 14 enlisted members. In addition there were 12...analysis; and research in the field of laboratory animal medicine and dentistry . The Clinical Investigations Department conducts research related to...MCU-2/P gas mask having a hose-attacheA’)canister system. Technical testing began and initial operational testing was completed. Ergonomic

Parameter identification of thermophilic anaerobic degradation of valerate.

PubMed

Flotats, Xavier; Ahring, Birgitte K; Angelidaki, Irini

2003-01-01

The considered mathematical model of the decomposition of valerate presents three unknown kinetic parameters, two unknown stoichiometric coefficients, and three unknown initial concentrations for biomass. Applying a structural identifiability study, we concluded that it is necessary to perform simultaneous batch experiments with different initial conditions for estimating these parameters. Four simultaneous batch experiments were conducted at 55 degrees C, characterized by four different initial acetate concentrations. Product inhibition of valerate degradation by acetate was considered. Practical identification was done optimizing the sum of the multiple determination coefficients for all measured state variables and for all experiments simultaneously. The estimated values of kinetic parameters and stoichiometric coefficients were characterized by the parameter correlation matrix, the confidence interval, and the student's t-test at 5% significance level with positive results except for the saturation constant, for which more experiments for improving its identifiability should be conducted. In this article, we discuss kinetic parameter estimation methods.

Characterization of the Edge Crack Torsion (ECT) Test for Mode III Fracture Toughness Measurement of Laminated Composites

NASA Technical Reports Server (NTRS)

Ratcliffe, James G.

2004-01-01

The edge crack torsion (ECT) test is designed to initiate mode III delamination growth in composite laminates. An ECT specimen is a rectangular laminate, containing an edge delamination at the laminate mid-plane. Torsion load is applied to the specimens, resulting in relative transverse shear sliding of the delaminated faces. The test data reduction schemes are intended to yield initiation values of critical mode III strain energy release rate, G(sub IIIc), that are constant with delamination length. The test has undergone several design changes during its development. The objective of this paper was to determine the suitability of the current ECT test design as a mode III fracture test. To this end, ECT tests were conducted on specimens manufactured from IM7/8552 and specimens made from S2/8552 tape laminates. Several specimens, each with different delamination lengths are tested. Detailed, three-dimensional finite element analyses of the specimens were performed. The analysis results were used to calculate the distribution of mode I, mode II, and mode III strain energy release rate along the delamination front. The results indicated that mode III-dominated delamination growth would be initiated from the specimen center. However, in specimens of both material types, the measured values of G(sub IIIc) exhibited significant dependence on delamination length. Furthermore, there was a large amount of scatter in the data. Load-displacement response of the specimens exhibited significant deviation from linearity before specimen failure. X-radiographs of a sample of specimens revealed that damage was initiated in the specimens prior to failure. Further inspection of the failure surfaces is required to identify the damage and determine that mode III delamination is initiated in the specimens.

40 CFR 63.6611 - By what date must I conduct the initial performance tests or other initial compliance...

Code of Federal Regulations, 2010 CFR

2010-07-01

... stationary RICE with a site rating of greater than or equal to 250 and less than or equal to 500 brake HP... demonstrations if I own or operate a 4SLB SI stationary RICE with a site rating of greater than or equal to 250... operate a new or reconstructed 4SLB stationary RICE with a site rating of greater than or equal to 250 and...

Development and initial evaluation of a reconstituted water formulation that better represents natural waters(poster)

EPA Science Inventory

The use of reconstituted waters is deeply entrenched in many standardized aquatic toxicity testing protocols The primary appeal of reconstituted waters is inter-laboratory comparability, such that experiments performed in different laboratories can be conducted in (nominally) id...

Development and Initial Evaluation of a Reconstituted Water Formulation that Better Represents Natural Waters

EPA Science Inventory

The use of reconstituted waters is deeply entrenched in many standardized aquatic toxicity testing protocols. The primary appeal of reconstituted waters is inter-laboratory comparability, such that experiments performed in different laboratories can be conducted in (nominally) id...

1995 Truck Size and Weight Performance-Based Workshop report : activity 5 : document North American and European experiences

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Technical Capability Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM proje...

Multibar sawless lint cleaner: Field testing results

USDA-ARS?s Scientific Manuscript database

The Multibar Sawless Lint Cleaner (MBSLC) is a prototype spiked-tooth lint cleaner initially designed to replace the first stage lint cleaning in a cotton gin. Previous studies conducted in the ginning laboratory in Lubbock, Texas, demonstrated improvements in some fiber properties, as well as minim...

Advanced Space Suit Insulation Feasibility Study

NASA Technical Reports Server (NTRS)

Trevino, Luis A.; Orndoff, Evelyne S.

2000-01-01

For planetary applications, the space suit insulation has unique requirements because it must perform in a dynamic mode to protect humans in the harsh dust, pressure and temperature environments. Since the presence of a gaseous planetary atmosphere adds significant thermal conductance to the suit insulation, the current multi-layer flexible insulation designed for vacuum applications is not suitable in reduced pressure planetary environments such as that of Mars. Therefore a feasibility study has been conducted at NASA to identify the most promising insulation concepts that can be developed to provide an acceptable suit insulation. Insulation concepts surveyed include foams, microspheres, microfibers, and vacuum jackets. The feasibility study includes a literature survey of potential concepts, an evaluation of test results for initial insulation concepts, and a development philosophy to be pursued as a result of the initial testing and conceptual surveys. The recommended focus is on microfibers due to the versatility of fiber structure configurations, the wide choice of fiber materials available, the maturity of the fiber processing industry, and past experience with fibers in insulation applications

A Summary of NASA Research Exploring the Acoustics of Small Unmanned Aerial Systems

NASA Technical Reports Server (NTRS)

Zawodny, Nikolas S.; Christian, Andrew; Cabell, Randolph

2018-01-01

Proposed uses of small unmanned aerial systems (sUAS) have the potential to expose large portions of communities to a new noise source. In order to understand the potential noise impact of sUAS, NASA initiated acoustics research as one component of the 3-year DELIVER project, with the goal of documenting the feasibility of using existing aircraft design tools and methods on this class of vehicles. This paper summarizes the acoustics research conducted within the DELIVER project. The research described here represents an initial study, and subsequent research building on the findings of this work has been proposed for other NASA projects. The paper summarizes acoustics research in four areas: measurements of noise generated by flyovers of small unmanned aerial vehicles, measurements in controlled test facilities to understand the noise generated by components of these vehicles, computational predictions of component and full vehicle noise, and psychoacoustic tests including auralizations conducted to assess human annoyance to the noise generated by these vehicles.

The Assessment, Development, Assurance Pharmacist's Tool (ADAPT) for ensuring quality implementation of health promotion programs.

PubMed

Truong, Hoai-An; Taylor, Catherine R; DiPietro, Natalie A

2012-02-10

To develop and validate the Assessment, Development, Assurance Pharmacist's Tool (ADAPT), an instrument for pharmacists and student pharmacists to use in developing and implementing health promotion programs. The 36-item ADAPT instrument was developed using the framework of public health's 3 core functions (assessment, policy development, and assurance) and 10 essential services. The tool's content and usage was assessed and conducted through peer-review and initial validity testing processes. Over 20 faculty members, preceptors, and student pharmacists at 5 institutions involved in planning and implementing health promotion initiatives reviewed the instrument and conducted validity testing. The instrument took approximately 15 minutes to complete and the findings resulted in changes and improvements to elements of the programs evaluated. The ADAPT instrument fills a need to more effectively plan, develop, implement, and evaluate pharmacist-directed public health programs that are evidence-based, high-quality, and compliant with laws and regulations and facilitates documentation of pharmacists' contributions to public health.

FETC/EPRI Biomass Cofiring Cooperative Agreement. Quarterly technical report, April 1-June 30, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hughes, E.; Tillman, D.

1997-12-01

The FETC/EPRI Biomass Cofiring Program has accelerated the pace of cofiring development by increasing the testing activities plus the support activities for interpreting test results. Past tests conducted and analyzed include the Allen Fossil Plant and Seward Generating Station programs. On-going tests include the Colbert Fossil Plant precommercial test program, the Greenidge Station commercialization program, and the Blount St. Station switchgrass program. Tests in the formative stages included the NIPSCO cofiring test at Michigan City Generating Station. Analytical activities included modeling and related support functions required to analyze the cofiring test results, and to place those results into context. Amongmore » these activities is the fuel availability study in the Pittsburgh, PA area. This study, conducted for Duquesne Light, supports their initial investigation into reburn technology using wood waste as a fuel. This Quarterly Report, covering the third quarter of the FETC/EPRI Biomass Cofiring Program, highlights the progress made on the 16 projects funded under this cooperative agreement.« less

Lightweight fibrous nickel electrodes for nickel-hydrogen batteries

NASA Technical Reports Server (NTRS)

Britton, Doris L.

1989-01-01

The NASA Lewis Research Center is currently developing nickel electrodes for nickel-hydrogen batteries. These electrodes are lighter in weight and have higher energy densities than the heavier state-of-the-art sintered nickel electrodes. Lightweight fibrous materials or plaques are used as conductive supports for the nickel hydroxide active material. These materials are commercial products that are fabricated into nickel electrodes by electrochemically impregnating them with active material. Evaluation is performed in half cells structured in the bipolar configuration. Initial performance tests include capacity measurements at five discharge levels, C/2, 1.0C, 1.37C, 2.0C, and 2.74C. The electrodes that pass the initial tests are life cycle-tested in a low Earth orbit regime at 80 percent depth of discharge.

A Size Effect on the Fatigue Crack Growth Rate Threshold of Alloy 718

NASA Technical Reports Server (NTRS)

Garr, K. R.; Hresko, G. C., III

1998-01-01

Fatigue crack growth rate (FCGR) tests were conducted on Alloy 718 in the solution annealed and aged condition at room temperature. In each test, the FCGR threshold was measured using the decreasing (Delta)K method. Initial testing was at two facilities, one of which used C(T) specimens with W = 127 mm. Previous data at the other facility had been obtained with specimens with W = 50.8 mm. A comparison of test results at R = 0.1 showed that the threshold for the 127 mm specimen was considerably higher than that of the 50.8 mm specimen. A check showed that this difference was not due to a heat-to-heat or lab-to-lab variation. Additional tests were conducted on specimens with W = 25.4 mm and at other R values. Data for the various specimens is presented along with parameters usually used to describe threshold behavior.

Water flow algorithm decision support tool for travelling salesman problem

NASA Astrophysics Data System (ADS)

Kamarudin, Anis Aklima; Othman, Zulaiha Ali; Sarim, Hafiz Mohd

2016-08-01

This paper discuss about the role of Decision Support Tool in Travelling Salesman Problem (TSP) for helping the researchers who doing research in same area will get the better result from the proposed algorithm. A study has been conducted and Rapid Application Development (RAD) model has been use as a methodology which includes requirement planning, user design, construction and cutover. Water Flow Algorithm (WFA) with initialization technique improvement is used as the proposed algorithm in this study for evaluating effectiveness against TSP cases. For DST evaluation will go through usability testing conducted on system use, quality of information, quality of interface and overall satisfaction. Evaluation is needed for determine whether this tool can assists user in making a decision to solve TSP problems with the proposed algorithm or not. Some statistical result shown the ability of this tool in term of helping researchers to conduct the experiments on the WFA with improvements TSP initialization.

Engaging Frontline Staff in Performance Improvement: The American Organization of Nurse Executives Implementation of Transforming Care at the Bedside Collaborative.

PubMed

Needleman, Jack; Pearson, Marjorie L; Upenieks, Valda V; Yee, Tracy; Wolstein, Joelle; Parkerton, Melissa

2016-02-01

Process improvement stresses the importance of engaging frontline staff in implementing new processes and methods. Yet questions remain on how to incorporate these activities into the workday of hospital staff or how to create and maintain its commitment. In a 15-month American Organization of Nurse Executives collaborative involving frontline medical/surgical staff from 67 hospitals, Transforming Care at the Bedside (TCAB) was evaluated to assess whether participating units successfully implemented recommended change processes, engaged staff, implemented innovations, and generated support from hospital leadership and staff. In a mixed-methods analysis, multiple data sources, including leader surveys, unit staff surveys, administrative data, time study data, and collaborative documents were used. All units reported establishing unit-based teams, of which >90% succeeded in conducting tests of change, with unit staff selecting topics and making decisions on adoption. Fifty-five percent of unit staff reported participating in unit meetings, and 64%, in tests of change. Unit managers reported substantial increase in staff support for the initiative. An average 36 tests of change were conducted per unit, with 46% of tested innovations sustained, and 20% spread to other units. Some 95% of managers and 97% of chief nursing officers believed that the program had made unit staff more likely to initiate change. Among staff, 83% would encourage adoption of the initiative. Given the strong positive assessment of TCAB, evidence of substantial engagement of staff in the work, and the high volume of innovations tested, implemented, and sustained, TCAB appears to be a productive model for organizing and implementing a program of frontline-led improvement.

Evaluation program for secondary spacecraft cells: Initial evaluation tests of Eagel-Picher Industries, Incorporated, 20.0 amphere-hour nickel-cadmium spacecraft cells

NASA Technical Reports Server (NTRS)

Harkness, J. D.

1974-01-01

An evaluation test of the 20.0 ampere-hour cells was conducted to insure that all cells put into the life cycle program are of high quality. This is accomplished by the screening of cells found to have electrolyte leakage, internal shorts, low capacity, or inability of any cell to recover its open circuit voltage above 1.150 volts during the internal short test. The results obtained in the test are given, as well as the recommendations based on these findings.

Organizing, staffing and initiating the program.

NASA Technical Reports Server (NTRS)

Van Biene, F. K.

1972-01-01

This paper describes and discusses those test laboratory management considerations prerequisite to test conduct and test reporting. These considerations are identified as (1) organizational requirements; they have to be determined, not only to implement a successful test program, but to match the communications needs of the other elements of the parent organization: (2) the role of supervision; decision making processes, types of decisions, and charters and role statements are presented: (3) planning; involves establishing objectives, definitions, procedures and the review and appraisal process: (4) delegation; some things cannot be delegated, others have to be.

Test-Case Generation using an Explicit State Model Checker Final Report

NASA Technical Reports Server (NTRS)

Heimdahl, Mats P. E.; Gao, Jimin

2003-01-01

In the project 'Test-Case Generation using an Explicit State Model Checker' we have extended an existing tools infrastructure for formal modeling to export Java code so that we can use the NASA Ames tool Java Pathfinder (JPF) for test case generation. We have completed a translator from our source language RSML(exp -e) to Java and conducted initial studies of how JPF can be used as a testing tool. In this final report, we provide a detailed description of the translation approach as implemented in our tools.

Statistical analysis of Turbine Engine Diagnostic (TED) field test data

NASA Astrophysics Data System (ADS)

Taylor, Malcolm S.; Monyak, John T.

1994-11-01

During the summer of 1993, a field test of turbine engine diagnostic (TED) software, developed jointly by U.S. Army Research Laboratory and the U.S. Army Ordnance Center and School, was conducted at Fort Stuart, GA. The data were collected in conformance with a cross-over design, some of whose considerations are detailed. The initial analysis of the field test data was exploratory, followed by a more formal investigation. Technical aspects of the data analysis insights that were elicited are reported.

Endeavour Impulse Tests

NASA Image and Video Library

2003-10-27

In the Orbiter Processing Facility, Eric Madaras, NASA-Langley Research Center, conducts impulse tests on the right wing leading edge (WLE) of Space Shuttle Endeavour. The tests monitor how sound impulses propagate through the WLE area. The data collected will be analyzed to explore the possibility of adding new instrumentation to the wing that could automatically detect debris or micrometeroid impacts on the Shuttle while in flight. The study is part of the initiative ongoing at KSC and around the agency to return the orbiter fleet to flight status.

The effect of laser focus and process parameters on microstructure and mechanical properties of SLM Inconel 718

NASA Astrophysics Data System (ADS)

Bean, Glenn E.; Witkin, David B.; McLouth, Tait D.; Zaldivar, Rafael J.

2018-02-01

Research on the selective laser melting (SLM) method of laser powder bed fusion additive manufacturing (AM) has shown that surface and internal quality of AM parts is directly related to machine settings such as laser energy density, scanning strategies, and atmosphere. To optimize laser parameters for improved component quality, the energy density is typically controlled via laser power, scanning rate, and scanning strategy, but can also be controlled by changing the spot size via laser focal plane shift. Present work being conducted by The Aerospace Corporation was initiated after observing inconsistent build quality of parts printed using OEM-installed settings. Initial builds of Inconel 718 witness geometries using OEM laser parameters were evaluated for surface roughness, density, and porosity while varying energy density via laser focus shift. Based on these results, hardware and laser parameter adjustments were conducted in order to improve build quality and consistency. Tensile testing was also conducted to investigate the effect of build plate location and laser settings on SLM 718. This work has provided insight into the limitations of OEM parameters compared with optimized parameters towards the goal of manufacturing aerospace-grade parts, and has led to the development of a methodology for laser parameter tuning that can be applied to other alloy systems. Additionally, evidence was found that for 718, which derives its strength from post-manufacturing heat treatment, there is a possibility that tensile testing may not be perceptive to defects which would reduce component performance. Ongoing research is being conducted towards identifying appropriate testing and analysis methods for screening and quality assurance.

Clinch River - Environmental Restoration Program (CR-ERP) pilot study, ambient water toxicity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simbeck, D.J.

1997-06-01

Clinch River - Environmental Restoration Program (CR-ERP) personnel and Tennessee Valley Authority (TVA) personnel conducted a pilot study during the week of April 22-29, 1993, prior to initiation of CR-ERP Phase II Sampling and Analysis activities as described in the Statement of Work (SOW) document. The organisms specified for testing were larval fathead minnows, Pimephales promelas, and the daphnid, Ceriodaphnia dubia. Surface water samples were collected by TVA Field Engineering personnel from Clinch River Mile 9.0 and Poplar Creek Kilometer 1.6 on April 21, 23, and 26. Samples were split and provided to the CR-ERP and TVA toxicology laboratories formore » testing. Exposure of test organisms to these samples resulted in no toxicity (survival, growth, or reproduction) to either species in testing conducted by TVA.« less

Effect of end-ring stiffness on buckling of pressure-loaded stiffened conical shells

NASA Technical Reports Server (NTRS)

Davis, R. C.; Williams, J. G.

1977-01-01

Buckling studies were conducted on truncated 120 deg conical shells having large end rings and many interior reinforcing rings that are typical of aeroshells used as spacecraft decelerators. Changes in base-end-ring stiffness were accomplished by simply machining away a portion of the base ring between successive buckling tests. Initial imperfection measurements from the test cones were included in the analytical model.

Laser-heated rotating specimen autoignition test

NASA Technical Reports Server (NTRS)

Au, A. C.

1988-01-01

Specimens of 440 C steel were rotated in a chamber pressurized with oxygen gas and heated with a 5-kW CO2 laser to determine the temperature required for autoignition to occur. Tests included exposures of static and rotating (25,000 rpm) specimens in oxygen pressurized to 5.51 MPa, and with focused laser fluences of more than 3.5 billion W/sq m. Specimen surface temperatures were monitored with a scanning infrared camera. Temperature measurement difficulties were experienced due to a problem with internal reflection inside the test chamber; however, posttest specimen examinations confirmed that surface melt (1371 C) was achieved in several tests. No sustained combustion was initiated in any rotating specimen. One static specimen was ignited. Results indicated that conditions necessary for autoignition of 440 C steel are more dependent on specimen geometry and available heat removal mechanisms. Sustained combustion occurred in the ignited static specimen with an estimated 130 C/sec cooling rate due to conduction. The rotating specimens could not sustain combustion due to a greater conductive/convective cooling rate of about 4000 C/sec and ejection of molten material. These results were applied to the Space Shuttle Main Engine (SSME) oxygen turbopump bearings to conclude that the LOX-cooled 440 C steel bearings cannot sustain combustion initiated by skidding friction.

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, Bill Prosser (left) and Eric Madaras, NASA-Langley Research Center, and Jim McGee (right), The Boeing Company, Huntington Beach, Calif., conduct impulse tests on the right wing leading edge (WLE) of Space Shuttle Endeavour. The tests monitor how sound impulses propagate through the WLE area. The data collected will be analyzed to explore the possibility of adding new instrumentation to the wing that could automatically detect debris or micrometeroid impacts on the Shuttle while in flight. The study is part of the initiative ongoing at KSC and around the agency to return the orbiter fleet to flight status.

NASA Image and Video Library

2003-10-27

KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility, Bill Prosser (left) and Eric Madaras, NASA-Langley Research Center, and Jim McGee (right), The Boeing Company, Huntington Beach, Calif., conduct impulse tests on the right wing leading edge (WLE) of Space Shuttle Endeavour. The tests monitor how sound impulses propagate through the WLE area. The data collected will be analyzed to explore the possibility of adding new instrumentation to the wing that could automatically detect debris or micrometeroid impacts on the Shuttle while in flight. The study is part of the initiative ongoing at KSC and around the agency to return the orbiter fleet to flight status.

Enhanced In-Pile Instrumentation at the Advanced Test Reactor

NASA Astrophysics Data System (ADS)

Rempe, Joy L.; Knudson, Darrell L.; Daw, Joshua E.; Unruh, Troy; Chase, Benjamin M.; Palmer, Joe; Condie, Keith G.; Davis, Kurt L.

2012-08-01

Many of the sensors deployed at materials and test reactors cannot withstand the high flux/high temperature test conditions often requested by users at U.S. test reactors, such as the Advanced Test Reactor (ATR) at the Idaho National Laboratory. To address this issue, an instrumentation development effort was initiated as part of the ATR National Scientific User Facility in 2007 to support the development and deployment of enhanced in-pile sensors. This paper provides an update on this effort. Specifically, this paper identifies the types of sensors currently available to support in-pile irradiations and those sensors currently available to ATR users. Accomplishments from new sensor technology deployment efforts are highlighted by describing new temperature and thermal conductivity sensors now available to ATR users. Efforts to deploy enhanced in-pile sensors for detecting elongation and real-time flux detectors are also reported, and recently-initiated research to evaluate the viability of advanced technologies to provide enhanced accuracy for measuring key parameters during irradiation testing are noted.

Thermoelectric converter for SP-100 space reactor power system

NASA Technical Reports Server (NTRS)

Terrill, W. R.; Haley, V. F.

1986-01-01

Conductively coupling the thermoelectric converter to the heat source and the radiator maximizes the utilization of the reactor and radiator temperatures and thereby minimizes the power system weight. This paper presents the design for the converter and the individual thermoelectric cells that are the building block modules for the converter. It also summarizes progress on the fabrication of initial cells and the results obtained from the preparation of a manufacturing plan. The design developed for the SP-100 system utilizes thermally conductive compliant pads that can absorb the displacement and distortion caused by the combinations of temperatures and thermal expansion coefficients. The converter and cell designs provided a 100 kWe system which met the system requirements. Initial cells were fabricated and tested.

NASA GRC Technology Development Project for a Stirling Radioisotope Power System

NASA Technical Reports Server (NTRS)

Thieme, Lanny G.; Schreiber, Jeffrey G.

2000-01-01

NASA Glenn Research Center (GRC), the Department of Energy (DOE), and Stirling Technology Company (STC) are developing a Stirling convertor for an advanced radioisotope power system to provide spacecraft on-board electric power for NASA deep space missions. NASA GRC is conducting an in-house project to provide convertor, component, and materials testing and evaluation in support of the overall power system development. A first characterization of the DOE/STC 55-We Stirling Technology Demonstration Convertor (TDC) under the expected launch random vibration environment was recently completed in the NASA GRC Structural Dynamics Laboratory. Two TDCs also completed an initial electromagnetic interference (EMI) characterization at NASA GRC while being tested in a synchronized, opposed configuration. Materials testing is underway to support a life assessment of the heater head, and magnet characterization and aging tests have been initiated. Test facilities are now being established for an independent convertor performance verification and technology development. A preliminary Failure Mode Effect Analysis (FMEA), initial finite element analysis (FEA) for the linear alternator, ionizing radiation survivability assessment, and radiator parametric study have also been completed. This paper will discuss the status, plans, and results to date for these efforts.

Analyses and estimates of hydraulic conductivity from slug tests in alluvial aquifer underlying Air Force Plant 4 and Naval Air Station-Joint Reserve Base Carswell Field, Fort Worth, Texas

USGS Publications Warehouse

Houston, Natalie A.; Braun, Christopher L.

2004-01-01

This report describes the collection, analyses, and distribution of hydraulic-conductivity data obtained from slug tests completed in the alluvial aquifer underlying Air Force Plant 4 and Naval Air Station-Joint Reserve Base Carswell Field, Fort Worth, Texas, during October 2002 and August 2003 and summarizes previously available hydraulic-conductivity data. The U.S. Geological Survey, in cooperation with the U.S. Air Force, completed 30 slug tests in October 2002 and August 2003 to obtain estimates of horizontal hydraulic conductivity to use as initial values in a ground-water-flow model for the site. The tests were done by placing a polyvinyl-chloride slug of known volume beneath the water level in selected wells, removing the slug, and measuring the resulting water-level recovery over time. The water levels were measured with a pressure transducer and recorded with a data logger. Hydraulic-conductivity values were estimated from an analytical relation between the instantaneous displacement of water in a well bore and the resulting rate of head change. Although nearly two-thirds of the tested wells recovered 90 percent of their slug-induced head change in less than 2 minutes, 90-percent recovery times ranged from 3 seconds to 35 minutes. The estimates of hydraulic conductivity range from 0.2 to 200 feet per day. Eighty-three percent of the estimates are between 1 and 100 feet per day.

Simulations for the Assessment of Counselling Skills.

ERIC Educational Resources Information Center

Smit, Gertrude N.; van der Molen, Henk T.

1996-01-01

A Dutch undergraduate course in professional counseling skills uses simulation to test students' ability to conduct an initial client interview, using standardized case histories. A study investigated the effectiveness of the method with 160 course participants, 77 non-participants, and 12 professional counselors and found it useful for…

40 CFR 147.3107 - Mechanical integrity.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Oklahoma Indian Tribes § 147.3107 Mechanical integrity. (a) Monitoring of annulus pressure conducted pursuant to § 146.8(b)(1) shall be preceded by an initial pressure test. A positive gauge pressure on the casing/tubing annulus (filled with liquid) shall be maintained continuously. The pressure shall be...

40 CFR 147.3107 - Mechanical integrity.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Oklahoma Indian Tribes § 147.3107 Mechanical integrity. (a) Monitoring of annulus pressure conducted pursuant to § 146.8(b)(1) shall be preceded by an initial pressure test. A positive gauge pressure on the casing/tubing annulus (filled with liquid) shall be maintained continuously. The pressure shall be...

40 CFR 147.3107 - Mechanical integrity.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Oklahoma Indian Tribes § 147.3107 Mechanical integrity. (a) Monitoring of annulus pressure conducted pursuant to § 146.8(b)(1) shall be preceded by an initial pressure test. A positive gauge pressure on the casing/tubing annulus (filled with liquid) shall be maintained continuously. The pressure shall be...

40 CFR 147.3107 - Mechanical integrity.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Oklahoma Indian Tribes § 147.3107 Mechanical integrity. (a) Monitoring of annulus pressure conducted pursuant to § 146.8(b)(1) shall be preceded by an initial pressure test. A positive gauge pressure on the casing/tubing annulus (filled with liquid) shall be maintained continuously. The pressure shall be...

49 CFR 240.123 - Criteria for initial and continuing education.

Code of Federal Regulations, 2010 CFR

2010-10-01

... that each engineer maintains the necessary knowledge, skill and ability concerning personal safety... both knowledge and performance skill testing; (3) Is conducted under the supervision of a qualified... whenever possible; (ii) Place the student engineer at the controls of a locomotive for a significant...

A qualitative assessment of the role of shippers and others in driver compliance with federal safety regulations

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Decision Support System Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM pr...

Static renewal tests using Pimephales promelas (fathead minnows) and Ceriodaphnia dubia (daphnids). Clinch River-Environmental Restoration Program (CR-ERP) pilot study, ambient water toxicity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simbeck, D.J.

1993-12-31

Clinch River-Environmental Restoration Program (CR-ERP) personnel and Tennessee Valley Authority (TVA) personnel conducted a pilot study during the week of April 22--29, 1993, prior to initiation of CR-ERP Phase 2 Sampling and Analysis activities. The organisms specified for testing were larval fathead minnows, Pimephales promelas, and the daphnid, Ceriodaphnia dubia. Surface water samples were collected by TVA Field Engineering personnel from Clinch River Mile 9.0 and Poplar Creek Kilometer 1.6 on April 21, 23, and 26. Samples were split and provided to the CR-ERP and TVA toxicology laboratories for testing. Exposure of test organisms to these samples resulted in nomore » toxicity (survival, growth, or reproduction) to either species in testing conducted by TVA. Attachments to this report include: Chain of custody forms -- originals; Toxicity test bench sheets and statistical analyses; Reference toxicant test information; and Personnel training documentation.« less

Demonstrating the Safety and Reliability of a New System or Spacecraft: Incorporating Analyses and Reviews of the Design and Processing in Determining the Number of Tests to be Conducted

NASA Technical Reports Server (NTRS)

Vesely, William E.; Colon, Alfredo E.

2010-01-01

Design Safety/Reliability is associated with the probability of no failure-causing faults existing in a design. Confidence in the non-existence of failure-causing faults is increased by performing tests with no failure. Reliability-Growth testing requirements are based on initial assurance and fault detection probability. Using binomial tables generally gives too many required tests compared to reliability-growth requirements. Reliability-Growth testing requirements are based on reliability principles and factors and should be used.

Implementation of Point-of-Care Diagnostics Leads to Variable Uptake of Syphilis, Anemia and CD4+ T-Cell Count Testing in Rural Maternal and Child Health Clinics.

PubMed

De Schacht, Caroline; Lucas, Carlota; Sitoe, Nádia; Machekano, Rhoderick; Chongo, Patrina; Temmerman, Marleen; Tobaiwa, Ocean; Guay, Laura; Kassaye, Seble; Jani, Ilesh V

2015-01-01

Anemia, syphilis and HIV are high burden diseases among pregnant women in sub-Saharan Africa. A quasi-experimental study was conducted in four health facilities in Southern Mozambique to evaluate the effect of point-of-care technologies for hemoglobin quantification, syphilis testing and CD4+ T-cell enumeration performed within maternal and child health services on testing and treatment coverage, and assessing acceptability by health workers. Demographic and testing data on women attending first antenatal care services were extracted from existing records, before (2011; n = 865) and after (2012; n = 808) introduction of point-of-care testing. Study outcomes per health facility were compared using z-tests (categorical variables) and Wilcoxon rank-sum test (continuous variables), while inverse variance weights were used to adjust for possible cluster effects in the pooled analysis. A structured acceptability-assessment interview was conducted with health workers before (n = 22) and after (n = 19). After implementation of point-of-care testing, there was no significant change in uptake of overall hemoglobin screening (67.9% to 83.0%; p = 0.229), syphilis screening (80.8% to 87.0%; p = 0.282) and CD4+ T-cell testing (84.9% to 83.5%; p = 0.930). Initiation of antiretroviral therapy for treatment eligible women was similar in the weighted analysis before and after, with variability among the sites. Time from HIV diagnosis to treatment initiation decreased (median of 44 days to 17 days; p<0.0001). A generally good acceptability for point-of-care testing was seen among health workers. Point-of-care CD4+ T-cell enumeration resulted in a decreased time to initiation of antiretroviral therapy among treatment eligible women, without significant increase in testing coverage. Overall hemoglobin and syphilis screening increased. Despite the perception that point-of-care technologies increase access to health services, the variability in results indicate the potential for detrimental effects in some settings. Local context needs to be considered and services restructured to accommodate innovative technologies in order to improve service delivery to expectant mothers.

The Effect of Using XO Computers on Students' Mathematics and Reading Abilities: Evidences from Learning Achievement Tests Conducted in Primary Education Schools in Mongolia

ERIC Educational Resources Information Center

Yamaguchi, Shinobu; Sukhbaatar, Javzan; Takada, Jun-ichi; Dayan-Ochir, Khishigbuyan

2014-01-01

In 2008, Mongolia took part in One Laptop per Child (OLPC) project. Since that time, over 10,000 students in grades 2-5 in 43 primary education schools are using XO computers. This paper presents the findings of a study conducted in 2012 to evaluate the impact of the OLPC initiatives on students' literacy and math skills. This study covered 14…

The effects of work engagement and self-efficacy on personal initiative and performance.

PubMed

Lisbona, Ana; Palaci, Francisco; Salanova, Marisa; Frese, Michael

2018-02-01

Two popular concepts, work engagement and personal initiative, are different but related constructs. This study is based on and extends the Frese and Fay (2001) model of personal initiative (PI) by including work engagement (WE) and self-efficacy as antecedents of PI, and performance as a consequence. Two studies (study 1, with a cross-sectional design using N = 396 participants from 22 organizations, and study 2, with a longitudinal design conducted in two waves with N = 118 participants from 15 organizations) test the hypotheses. Structural equation modeling and the PROCESS SPSS Macro were used to test the hypothesized mediating role of personal initiative in work engagement and performance, and the results show the indirect effect of WE on performance through PI. The results of these two studies confirmed our hypotheses: WE and self-efficacy lead to higher PI, which, in turn, leads to higher performance. In addition to considering WE as an antecedent of PI, the results lead to considering PI as an antecedent of performance.

Damage Accumulation and Failure of Plasma-Sprayed Thermal Barrier Coatings under Thermal Gradient Cyclic Conditions

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Choi, Sung R.; Ghosn, Louis J.; Miller, rober A.

2005-01-01

Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. A fundamental understanding of the sintering and thermal cycling induced delamination of thermal barrier coating systems under engine-like heat flux conditions will potentially help to improve the coating temperature capability. In this study, a test approach is established to emphasize the real-time monitoring and assessment of the coating thermal conductivity, which can initially increase under the steady-state high temperature thermal gradient test due to coating sintering, and later decrease under the thermal gradient cyclic test due to coating cracking and delamination. Thermal conductivity prediction models have been established for a ZrO2-(7- 8wt%)Y2O3 model coating system in terms of heat flux, time, and testing temperatures. The coating delamination accumulation is then assessed based on the observed thermal conductivity response under the combined steady-state and cyclic thermal gradient tests. The coating thermal gradient cycling associated delaminations and failure mechanisms under simulated engine heat-flux conditions will be discussed in conjunction with the coating sintering and fracture testing results.

Periodic Overload and Transport Spectrum Fatigue Crack Growth Tests of Ti62222STA and Al2024T3 Sheet

NASA Technical Reports Server (NTRS)

Phillips, Edward P.

1999-01-01

Variable amplitude loading crack growth tests have been conducted to provide data that can be used to evaluate crack growth prediction codes. Tests with periodic overloads or overloads followed by underloads were conducted on titanium alloy Ti-6Al-2Sn-2Zr-2Mo-2Cr solution treated and aged (Ti62222STA) material at room temperature and at 350 F. Spectrum fatigue crack growth tests were conducted on two materials (Ti62222STA and aluminum alloy 2024-T3) using two transport lower-wing test spectra at two temperatures (room temperature and 350 F (Ti only)). Test lives (growth from an initial crack half-length of 0.15 in. to failure) were recorded in all tests and the crack length against cycles (or flights) data were recorded in many of the tests. The following observations were made regarding the test results: (1) in tests of the Ti62222STA material, the tests at 350 F had longer lives than those at room temperature, (2) in tests to the MiniTwist spectrum, the Al2024T3 material showed much greater crack growth retardations due to the highest stresses in the spectrum than did the Ti62222STA material, and (3) comparisons of material crack growth performances on an "equal weight" basis were spectrum dependent.

Detecting Initiation or Risk for Initiation of Substance Use before High School during Pediatric Well-Child Check-Ups

PubMed Central

Ridenour, Ty A.; Willis, David; Bogen, Debra L.; Novak, Scott; Scherer, Jennifer; Reynolds, Maureen D.; Zhai, Zu Wei; Tarter, Ralph E.

2015-01-01

Background Youth substance use (SU) is prevalent and costly, affecting mental and physical health. American Academy of Pediatrics and Affordable Care Act call for SU screening and prevention. The Youth Risk Index© (YRI) was tested as a screening tool for having initiated and propensity to initiate SU before high school (which forecasts SU disorder). YRI was hypothesized to have good to excellent psychometrics, feasibility and stakeholder acceptability for use during well-child check-ups. Design A high-risk longitudinal design with two cross-sectional replication samples, ages 9–13 was used. Analyses included receiver operating characteristics and regression analyses. Participants A one-year longitudinal sample (N=640) was used for YRI derivation. Replication samples were a cross-sectional sample (N=345) and well-child check-up patients (N=105) for testing feasibility, validity and acceptability as a screening tool. Results YRI has excellent test-retest reliability and good sensitivity and specificity for concurrent and one-year-later SU (odds ratio=7.44 CI=4.3–13.0) and conduct problems (odds ratios=7.33 CI=3.9–13.7). Results were replicated in both cross-sectional samples. Well-child patients, parents and pediatric staff rated YRI screening as important, acceptable, and a needed service. Conclusions Identifying at-risk youth prior to age 13 could reap years of opportunity to intervene before onset of SU disorder. Most results pertained to YRI’s association with concurrent or recent past risky behaviors; further replication ought to specify its predictive validity, especially adolescent-onset risky behaviors. YRI well identifies youth at risk for SU and conduct problems prior to high school, is feasible and valid for screening during well-child check-ups, and is acceptable to stakeholders. PMID:25765481

Integrated Test and Evaluation (ITE) Flight Test Series 4

NASA Technical Reports Server (NTRS)

Marston, Michael

2016-01-01

The integrated Flight Test 4 (FT4) will gather data for the UAS researchers Sense and Avoid systems (referred to as Detect and Avoid in the RTCA SC 228 ToR) algorithms and pilot displays for candidate UAS systems in a relevant environment. The technical goals of FT4 are to: 1) perform end-to-end traffic encounter test of pilot guidance generated by DAA algorithms; 2) collect data to inform the initial Minimum Operational Performance Standards (MOPS) for Detect and Avoid systems. FT4 objectives and test infrastructure builds from previous UAS project simulations and flight tests. NASA Ames (ARC), NASA Armstrong (AFRC), and NASA Langley (LaRC) Research Centers will share responsibility for conducting the tests, each providing a test lab and critical functionality. UAS-NAS project support and participation on the 2014 flight test of ACAS Xu and DAA Self Separation (SS) significantly contributed to building up infrastructure and procedures for FT3 as well. The DAA Scripted flight test (FT4) will be conducted out of NASA Armstrong over an eight-week period beginning in April 2016.

PILOT SCALE PROCESS EVALUATION OF REBURNING FOR IN-FURNACE NOX REDUCTION

EPA Science Inventory

The report gives results of coal and natural gas reburning application tests to a pilot scale 3.0 MWt furnace to provide the scaling information required for commercial application of reburning to pulverized-coal-fired boilers. Initial parametric studies had been conducted in a 2...

Selecting honey bees for worker brood that reduces the reproduction of Varroa destructor

USDA-ARS?s Scientific Manuscript database

We investigated an effect of Apis mellifera worker brood on the reproduction of Varroa destructor as a resistance trait by conducting seven generations of bidirectional selection. Initial tests showed two-fold differences in mite fecundity (progeny per foundress mites) between colonies of different...

46 CFR 115.806 - Electrical.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Electrical. 115.806 Section 115.806 Shipping COAST GUARD....806 Electrical. At each initial and subsequent inspection for certification of a vessel, the owner or managing operator shall be prepared to conduct tests and have the vessel ready for inspection of electrical...

46 CFR 115.806 - Electrical.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Electrical. 115.806 Section 115.806 Shipping COAST GUARD....806 Electrical. At each initial and subsequent inspection for certification of a vessel, the owner or managing operator shall be prepared to conduct tests and have the vessel ready for inspection of electrical...

46 CFR 115.806 - Electrical.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Electrical. 115.806 Section 115.806 Shipping COAST GUARD....806 Electrical. At each initial and subsequent inspection for certification of a vessel, the owner or managing operator shall be prepared to conduct tests and have the vessel ready for inspection of electrical...

46 CFR 115.806 - Electrical.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Electrical. 115.806 Section 115.806 Shipping COAST GUARD....806 Electrical. At each initial and subsequent inspection for certification of a vessel, the owner or managing operator shall be prepared to conduct tests and have the vessel ready for inspection of electrical...

46 CFR 115.806 - Electrical.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Electrical. 115.806 Section 115.806 Shipping COAST GUARD....806 Electrical. At each initial and subsequent inspection for certification of a vessel, the owner or managing operator shall be prepared to conduct tests and have the vessel ready for inspection of electrical...

46 CFR 115.802 - Hull.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Hull. 115.802 Section 115.802 Shipping COAST GUARD....802 Hull. (a) At each initial and subsequent inspection for certification of a vessel, the owner or managing operator shall be prepared to conduct tests and have the vessel ready for inspections of the hull...

40 CFR 51.363 - Quality assurance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... per year per number of inspectors using covert vehicles set to fail (this requirement sets a minimum... stations that conduct both testing and repairs, at least one covert vehicle visit per station per year including the purchase of repairs and subsequent retesting if the vehicle is initially failed for tailpipe...

40 CFR 63.455 - Reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... submit an initial notification of the subsequent performance test to the Administrator as soon as... be conducted. The owner or operator shall notify the Administrator as soon as practicable, but no... provisions of § 63.453(p)(3), the owner or operator shall notify the Administrator as soon as practicable of...

40 CFR 63.455 - Reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... submit an initial notification of the subsequent performance test to the Administrator as soon as... be conducted. The owner or operator shall notify the Administrator as soon as practicable, but no... provisions of § 63.453(p)(3), the owner or operator shall notify the Administrator as soon as practicable of...

PNNI Performance Validation Test Report

NASA Technical Reports Server (NTRS)

Dimond, Robert P.

1999-01-01

Two Private Network-Network Interface (PNNI) neighboring peers were monitored with a protocol analyzer to understand and document how PNNI works with regards to initialization and recovery processes. With the processes documented, pertinent events were found and measured to determine the protocols behavior in several environments, which consisted of congestion and/or delay. Subsequent testing of the protocol in these environments was conducted to determine the protocol's suitability for use in satellite-terrestrial network architectures.

Comprehensive Nuclear-Test-Ban Treaty: Issues and Arguments

DTIC Science & Technology

2008-02-28

is the point at which this chain reaction occurs; a “ critical mass ” is the amount of fissile material just enough to support criticality . The...amount of material for a critical mass depends on many factors, such as shape, density, impurities that absorb neutrons, and use of material to reflect...the years. Hydronuclear experiments were conducted during the 1958-1961 nuclear test moratorium. They initially used less than a critical mass of

Avionics Integrity Program (AVIP). Volume 1. Procurement Phase Issues - Design, Manufacturing, and Integration

DTIC Science & Technology

1984-03-01

Engineering initiative to develop an orderly plan and procedure to assure that USAF acquire reliable, high quality, supportable avionics with a higher avail...susceptibility te~t~ (radiated and conducted), and emission of radio frequency energy tests."l6) Other electrical stresses can include over/under voltage...jo ints, poor welds, and dielectric defects. Also, instruments with components unable to endu very high temperatures can be safely tested. 1-19

Highly-flexible fibre battery incorporating polypyrrole cathode and carbon nanotubes anode

NASA Astrophysics Data System (ADS)

Wang, J.; Wang, C. Y.; Too, C. O.; Wallace, G. G.

The development of highly-flexible fibre batteries based on a conducting polymer and single-wall carbon nanotubes (SWNTs) is described. Initially, polypyrrole-hexafluorophosphate (PPy/PF 6) and SWNTs are tested in lithium cells to ascertain their performance. Based on the results, fibre batteries consisting of a PPy/PF 6 cathode and an anode based on SWNTs are fabricated and tested in both a "flooded cell" and 'dry cell', arrangement.

Data documentation for the bare soil experiment at the University of Arkansas

NASA Technical Reports Server (NTRS)

Waite, W. P.; Scott, H. D. (Principal Investigator); Hancock, G. D.

1980-01-01

The reflectivities of several controlled moisture test plots were investigated. These test plots were of a similar soil texture which was clay loam and were prepared to give a desired initial soil moisture and density profile. Measurements were conducted on the plots as the soil water redistributed for both long term and diurnal cycles. These measurements included reflectivity, gravimetric and volumetric soil moisture, soil moisture potential, and soil temperature.

US Army Biomedical Laboratory Annual Progress Report, 1 October 1986-30 September 1987. Volume 1

DTIC Science & Technology

1987-12-07

support of casualties during evacuation within the theater of operations . To fulfill this requirement USABRDL has initiated a project to identify and...Tests of its operational capabilities will be conducted. Aerial application of granular pesticide was done to control ticks at Fort A.P. Hill, Virginia...with limited amounts of hypochlorous acid ; and the testing of several polymeric and monomeric diacetylene compounds as potential indicators to be used

Pascal and High-School Students: A Study of Misconceptions. Technology Panel Study of Stanford and the Schools. Occasional Report #009.

ERIC Educational Resources Information Center

Sleeman, D.; And Others

In an attempt to initiate a new approach to the teaching of Pascal, a study was conducted to ascertain the difficulties students encountered when they attempt to learn this computer language. Screening tests were given to 68 students in grades 11 and 12 who had just completed a semester course in Pascal. The purpose of the test was to detect…

[A comparative analysis of the brain activity during the traditional and intensive forms of learning foreign languages].

PubMed

Bykova, L G; Bazylev, V N

1994-01-01

By means of dichotic test the comparative research of the brain activity in dynamics in 84 adult students was conducted during their traditional (36 persons) and intensive (48 persons) learning of foreign languages. By different methods of learning the reliable distinction of the hemisphere's asymmetry was not detected. By both methods in the reliable majority of students the activation of the hemisphere opposite to the one dominating initially was observed. The correlation between the maximum quantitative shift of the right ear coefficient and the level of success in colloquial practice by the same initial level of language start and initial comparable size of memory was revealed. The authors discuss the possibility of the individual map composition for every student using the results of dichotic tests in dynamics for the help in the profession of a teacher.

Hydraulic conductivity of compacted zeolites.

PubMed

Oren, A Hakan; Ozdamar, Tuğçe

2013-06-01

Hydraulic conductivities of compacted zeolites were investigated as a function of compaction water content and zeolite particle size. Initially, the compaction characteristics of zeolites were determined. The compaction test results showed that maximum dry unit weight (γ(dmax)) of fine zeolite was greater than that of granular zeolites. The γ(dmax) of compacted zeolites was between 1.01 and 1.17 Mg m(-3) and optimum water content (w(opt)) was between 38% and 53%. Regardless of zeolite particle size, compacted zeolites had low γ(dmax) and high w(opt) when compared with compacted natural soils. Then, hydraulic conductivity tests were run on compacted zeolites. The hydraulic conductivity values were within the range of 2.0 × 10(-3) cm s(-1) to 1.1 × 10(-7) cm s(-1). Hydraulic conductivity of all compacted zeolites decreased almost 50 times as the water content increased. It is noteworthy that hydraulic conductivity of compacted zeolite was strongly dependent on the zeolite particle size. The hydraulic conductivity decreased almost three orders of magnitude up to 39% fine content; then, it remained almost unchanged beyond 39%. Only one report was found in the literature on the hydraulic conductivity of compacted zeolite, which is in agreement with the findings of this study.

Reaction times to weak test lights. [psychophysics biological model

NASA Technical Reports Server (NTRS)

Wandell, B. A.; Ahumada, P.; Welsh, D.

1984-01-01

Maloney and Wandell (1984) describe a model of the response of a single visual channel to weak test lights. The initial channel response is a linearly filtered version of the stimulus. The filter output is randomly sampled over time. Each time a sample occurs there is some probability increasing with the magnitude of the sampled response - that a discrete detection event is generated. Maloney and Wandell derive the statistics of the detection events. In this paper a test is conducted of the hypothesis that the reaction time responses to the presence of a weak test light are initiated at the first detection event. This makes it possible to extend the application of the model to lights that are slightly above threshold, but still within the linear operating range of the visual system. A parameter-free prediction of the model proposed by Maloney and Wandell for lights detected by this statistic is tested. The data are in agreement with the prediction.

Development and Initial Testing of Messages to Encourage Tuberculosis Testing and Treatment Among Bacille Calmette-Guerin (BCG) Vaccinated Persons

PubMed Central

Galindo-Gonzalez, Sebastian; Irani, Tracy A.

2017-01-01

Misperceptions surrounding the Bacille Calmette-Guerin (BCG) vaccine can lead some vaccinated individuals to resist being tested and treated for tuberculosis (TB). Educational messages to best explain the risk of TB to BCG-vaccinated, Hispanic persons were systematically developed and tested. First, TB program staff provided messages they considered effective. These were analyzed and validated by TB experts, and then presented in group interviews initially to foreign-born Hispanic persons with a TB diagnosis, and then persons without a prior TB diagnosis. Based on interviewees’ feedback, preferred statements were used to develop one long and three short comprehensive messages. One-on-one interviews were conducted with Hispanic persons to assess the saliency of the comprehensive educational messages. Participants preferred messages that were gain or positively-framed and explained that BCG does not confer lifelong protection against TB. Participants confirmed the messages would likely have a positive impact on patient decisions to undergo TB testing and treatment. PMID:24141428

Progress in the Development of Lightweight Nickel Electrode for Nickel-Hydrogen Cell

NASA Technical Reports Server (NTRS)

Britton, Doris L.

1999-01-01

Development of a high specific energy battery is one of the objectives of the lightweight nickel-hydrogen (Ni-H2) program at the NASA Glenn Research Center. The approach has been to improve the nickel electrode by continuing combined in-house and contract efforts to develop a lighter weight electrode for the nickel-hydrogen cell. Small fiber diameter nickel plaques are used as conductive supports for the nickel hydroxide active material. These plaques are commercial products and have an advantage of increased surface area available for the deposition of active material. Initial tests include activation and capacity measurements at five different discharge levels, C/2, 1.0 C, 1.37 C, 2.0 C, and 2.74 C. The electrodes are life cycle tested using a half-cell configuration at 40 and 80% depths-of-discharge (DOD) in a low-Earth-orbit regime. The electrodes that pass the initial tests are life cycle-tested in a boiler plate nickel-hydrogen cell before flight weight design are built and tested.

Test Report for MSFC Test No. 83-2: Pressure scaled water impact test of a 12.5 inch diameter model of the Space Shuttle solid rocket booster filament wound case and external TVC PCD

NASA Technical Reports Server (NTRS)

1983-01-01

Water impact tests using a 12.5 inch diameter model representing a 8.56 percent scale of the Space Shuttle Solid Rocket Booster configuration were conducted. The two primary objectives of this SRB scale model water impact test program were: 1. Obtain cavity collapse applied pressure distributions for the 8.56 percent rigid body scale model FWC pressure magnitudes as a function of full-scale initial impact conditions at vertical velocities from 65 to 85 ft/sec, horizontal velocities from 0 to 45 ft/sec, and angles from -10 to +10 degrees. 2. Obtain rigid body applied pressures on the TVC pod and aft skirt internal stiffener rings at initial impact and cavity collapse loading events. In addition, nozzle loads were measured. Full scale vertical velocities of 65 to 85 ft/sec, horizontal velocities of 0 to 45 ft/sec, and impact angles from -10 to +10 degrees simulated.

Auto-Thermal Reforming of Jet-A Fuel over Commercial Monolith Catalysts: MicroReactor Evaluation and Screening Test Results

NASA Technical Reports Server (NTRS)

Yen, Judy C. H.; Tomsik, Thomas M.

2004-01-01

This paper describes the results of a series of catalyst screening tests conducted with Jet-A fuel under auto-thermal reforming (ATR) process conditions at the research laboratories of SOFCo-EFS Holdings LLC under Glenn Research Center Contract. The primary objective is to identify best available catalysts for future testing at the NASA GRC 10-kW(sub e) reformer test facility. The new GRC reformer-injector test rig construction is due to complete by March 2004. Six commercially available monolithic catalyst materials were initially selected by the NASA/SOFCo team for evaluation and bench scale screening in an existing 0.05 kW(sub e) microreactor test apparatus. The catalyst screening tests performed lasted 70 to 100 hours in duration in order to allow comparison between the different samples over a defined range of ATR process conditions. Aging tests were subsequently performed with the top two ranked catalysts as a more representative evaluation of performance in a commercial aerospace application. The two catalyst aging tests conducted lasting for approximately 600 hours and 1000 hours, respectively.

Apollo 14 visibility tests: Visibility of lunar surface features and lunar landing

NASA Technical Reports Server (NTRS)

Ziedman, K.

1972-01-01

An in-flight visibility test conducted on the Apollo 14 mission is discussed. The need for obtaining experimental data on lunar feature visibility arose from visibility problems associated with various aspects of the Apollo missions; and especially from anticipated difficulties of recognizing lunar surface features at the time of descent and landing under certain illumination conditions. Although visibility problems have influenced many other aspects of the Apollo mission, they have been particularly important for descent operations, due to the criticality of this mission phase and the crew's guidance and control role for landing site recognition and touchdown point selection. A series of analytical and photographic studies were conducted during the Apollo program (prior to as well as after the initial manned lunar operations) to delineate constraints imposed on landing operations by visibility limitations. The purpose of the visibility test conducted on Apollo 14 was to obtain data to reduce uncertainties and to extend the analytical models of visibility in the lunar environment.

Biological and Host Range Studies with Bagous affinis, An Indian Weevil that Destroys Hydrilla Tubers. Aquatic Plant Control Research Program.

DTIC Science & Technology

1994-12-01

three times with newly emerged adults and three times with adults at least a month old. Treatments were (a) four hydrilla sprigs, (b) four hydrilla...Methods conducted to determine if feeding on nonhost plants stimulated the develop- ment of flight muscles. Newly emerged females were held in a plastic...Fecundity and adult longevity A fecundity and adult longevity test was conducted with newly emerged adults. Adults were held initially with moist paper

Enumeration procedure for monitoring test microbe populations on inoculated carriers in AOAC use-dilution methods.

PubMed

Tomasino, Stephen F; Fiumara, Rebecca M; Cottrill, Michele P

2006-01-01

The AOAC Use-Dilution methods do not provide procedures to enumerate the test microbe on stainless steel carriers (penicylinders) or guidance on the expected target populations of the test microbe (i.e., a performance standard). This report describes the procedures used by the U.S. Environmental Protection Agency to enumerate the test microbe (carrier counts) associated with conducting the Use-Dilution method with Staphylococcus aureus (Method 955.15) and Pseudomonas aeruginosa (Method 964.02) and the examination of historical data. The carrier count procedure involves the random selection of carriers, shearing bacterial cells from the carrier surface through sonication, and plating of serially diluted inoculum on trypticase soy agar. For each Use-Dilution test conducted, the official AOAC method was strictly followed for carrier preparation, culture initiation, test culture preparation, and carrier inoculation steps. Carrier count data from 78 Use-Dilution tests conducted over a 6-year period were compiled and analyzed. A mean carrier count of 6.6 logs (approximately 4.0 x 10(6) colony-forming units/carrier) was calculated for both S. aureus and P. aeruginosa. Of the mean values, 95% fell within +/- 2 repeatability standard deviations. The enumeration procedure and target carrier counts are desirable for standardizing the Use-Dilution methods, increasing their reproducibility, and ensuring the quality of the data.

Impact of Heterogeneity on Vadose Zone Drainage During Pumping: Numerical Simulations of the Borden Aquifer

NASA Astrophysics Data System (ADS)

Bunn, M. I.; Jones, J.; Endres, A. L.

2009-05-01

Unconfined aquifers are in direct contact with the earth's surface; hence, they are an important focus in groundwater recharge and contaminant transport studies. While pumping tests have long been used to quantify aquifer properties, the contribution of drainage from the vadose zone during pumping has been the subject of debate for decades. In 2001, a highly detailed data set was collected during a seven-day pumping test in the unconfined aquifer at CFB Borden, Ontario (Bevan et al., 2005). The frequent observation of moisture content profiles during the test has initiated a closer examination of the vadose zone response to pumping. The moisture profiles collected during the test were obtained using a neutron probe. The neutron data depicts a capillary fringe thickness that increases with both proximity to the pumping well and duration of pumping. This capillary fringe extension results in delayed drainage that persists to the end of the seven-day test with the shape of the transition zone remaining constant (Bevan et al., 2005). Simulations of the pumping test were conducted using Hydrogeosphere (Therrien et al., 2006). Initial simulations were completed based on the conceptual model of a homogeneous and slightly anisotropic aquifer. The simulation results replicated the observed piezometric response, but were unable to produce any change in the thickness of the capillary fringe. It was hypothesized that the discrepancy between observations and simulation results may be the result of assumptions such as the homogeneity of the hydraulic conductivity field. In an effort to replicate this potential mechanism for the observed extension, the conceptual model was updated to better reflect the mildly heterogeneous hydraulic conductivity field of the Borden aquifer. Conductivity fields were generated using the statistical description of the Borden aquifer given by Sudicky (1986) with an adjusted mean log conductivity to better approximate the observed piezometric response. The inclusion of heterogeneity appears to have little effect on the hydraulic head drawdown, or the thickness of the capillary fringe. Heterogeneity does lead to delayed drainage in the drier portion of the vadose zone, where volumetric water content is less than 0.13 m3/m3. This effect is more pronounced with proximity to the pumping well, and is negligible at 15 m from the well. The amount of excess moisture in the vadose zone does not appear to be a function of pumping duration.

Crystallographic Analysis of Fatigue Crack Initiation Behavior in Coarse-Grained Magnesium Alloy Under Tension-Tension Loading Cycles

NASA Astrophysics Data System (ADS)

Tamada, Kazuhiro; Kakiuchi, Toshifumi; Uematsu, Yoshihiko

2017-07-01

Plane bending fatigue tests are conducted to investigate fatigue crack initiation mechanisms in coarse-grained magnesium alloy, AZ31, under the stress ratios R = -1 and 0.1. The initial crystallographic structures are analyzed by an electron backscatter diffraction method. The slip or twin operation during fatigue tests is identified from the line angle analyses based on Euler angles of the grains. Under the stress ratio R = -1, relatively thick tension twin bands are formed in coarse grains. Subsequently, compression twin or secondary pyramidal slip operates within the tension twin band, resulting in the fatigue crack initiation. On the other hand, under R = 0.1 with tension-tension loading cycles, twin bands are formed on the specimen surface, but the angles of those bands do not correspond to tension twins. Misorientation analyses of c-axes in the matrix grain and twin band reveal that double twins are activated. Under R = 0.1, fatigue crack initiates along the double twin boundaries. The different manners of fatigue crack initiation at R = -1 and 0.1 are related to the asymmetricity of twining under tension and compression loadings. The fatigue strengths under different stress ratios cannot be estimated by the modified Goodman diagram due to the effect of stress ratio on crack initiation mechanisms.

Data book for 12.5-inch diameter SRB thermal model water flotation test - 14.7 psia, series P024

NASA Technical Reports Server (NTRS)

Allums, S. L.

1974-01-01

Tests were conducted to determine how thermal conditions affect space shuttle solid rocket booster (SRB) flotation. Acceleration, pressure, and temperature data were recorded from initial water impact to final flotation position using a 12.5-inch diameter thermal model of the SRB at ambient pressure. The model was 136.9 inches long and weighed 117.3 lbm. The tests indicated the following differences from ambient temperature tests: (1) significant negative static pressures can occur during penetration; (2) maximum penetration is increased; and (3) final flotation is in the spar buoy mode.

Preparation and properties of polytetrafluoroethylene impregnated with rhenium oxides

NASA Technical Reports Server (NTRS)

Leibecki, H. F.; Easter, R. W.

1973-01-01

The results of tests carried out to determine the properties of polytetrafluorethylene (PTFE) impregnated with rhenium oxides are presented. The tests included measurement of physical properties of the impregnated material and investigation of the effects of preparation process variables. Based on the latter tests a mechanism to describe the permeation process is postulated which identifies the rate controlling step to be diffusion of ReF6 molecules into the solid during the initial ReF6 soak. Physical property tests indicated that the electronic conductance is increased by many orders of magnitude while the desirable properties of the PTFE remain virtually unchanged.

Initial development and psychometric testing of an instrument to measure the quality of children's end-of-life care.

PubMed

Widger, Kimberley; Tourangeau, Ann E; Steele, Rose; Streiner, David L

2015-01-01

The field of pediatric palliative care is hindered by the lack of a well-defined, reliable, and valid method for measuring the quality of end-of-life care. The study purpose was to develop and test an instrument to measure mothers' perspectives on the quality of care received before, at the time of, and following a child's death. In Phase 1, key components of quality end-of-life care for children were synthesized through a comprehensive review of research literature. These key components were validated in Phase 2 and then extended through focus groups with bereaved parents. In Phase 3, items were developed to assess structures, processes, and outcomes of quality end-of-life care then tested for content and face validity with health professionals. Cognitive testing was conducted through interviews with bereaved parents. In Phase 4, bereaved mothers were recruited through 10 children's hospitals/hospices in Canada to complete the instrument, and psychometric testing was conducted. Following review of 67 manuscripts and 3 focus groups with 10 parents, 141 items were initially developed. The overall content validity index for these items was 0.84 as rated by 7 health professionals. Based on feedback from health professionals and cognitive testing with 6 parents, a 144-item instrument was finalized for further testing. In Phase 4, 128 mothers completed the instrument, 31 of whom completed it twice. Test-retest reliability, internal consistency, and construct validity were demonstrated for six subscales: Connect With Families, Involve Parents, Share Information With Parents, Share Information Among Health Professionals, Support Parents, and Provide Care at Death. Additional items with content validity were grouped in four domains: Support the Child, Support Siblings, Provide Bereavement Follow-up, and Structures of Care. Forty-eight items were deleted through psychometric testing, leaving a 95-item instrument. There is good initial evidence for the reliability and validity of this new quality of end-of-life care instrument as a mechanism for evaluative feedback to health professionals, health systems, and policy makers to improve children's end-of-life care.

Some lessons from NACA/NASA aerodynamic studies following World War II

NASA Technical Reports Server (NTRS)

Spearman, M. L.

1983-01-01

An historical account is presented of the new departures in aerodynamic research conducted by NACA, and subsequently NASA, as a result of novel aircraft technologies and operational regimes encountered in the course of the Second World War. The invention and initial development of the turbojet engine furnished the basis for a new speed/altitude regime in which numerous aerodynamic design problems arose. These included compressibility effects near the speed of sound, with attendant lift/drag efficiency reductions and longitudinal stability enhancements that were accompanied by a directional stability reduction. Major research initiatives were mounted in the investigation of swept, delta, trapezoidal and variable sweep wing configurations, sometimes conducted through flight testing of the 'X-series' aircraft. Attention is also given to the development of the first generation of supersonic fighter aircraft.

The views and experiences of nurses and midwives in the provision and management of provider-initiated HIV testing and counseling: a systematic review of qualitative evidence.

PubMed

Evans, Catrin; Nalubega, Sylivia; McLuskey, John; Darlington, Nicola; Croston, Michelle; Bath-Hextall, Fiona

2016-01-15

Global progress towards HIV prevention and care is contingent upon increasing the number of those aware of their status through HIV testing. Provider-initiated HIV testing and counseling is recommended globally as a strategy to enhance uptake of HIV testing and is primarily conducted by nurses and midwives. Research shows that provider-initiated HIV testing and counseling implementation is sub-optimal. The reasons for this are unclear. The review aimed to explore nurses' and midwives' views and experiences of the provision and management of provider-initiated HIV testing and counseling. All cadres of nurses and midwives were considered, including those who undertake routine HIV testing as part of a diverse role and those who are specifically trained as HIV counselors. Types of phenomenon of interest: The review sought to understand the views and experiences of the provision and management of provider-initiated HIV testing and counseling (including perceptions, opinions, beliefs, practices and strategies related to HIV testing and its implementation in practice). The review included only provider-initiated HIV testing and counseling. It excluded all other models of HIV testing. The review included all countries and all healthcare settings. Types of studies: This review considered all forms of qualitative study design and methodology. Qualitative elements of a mixed method study were included if they were presented separately within the publication. A three-step search strategy was utilized. Eight databases were searched for papers published from 1996 to October 2014, followed by hand searching of reference lists. Only studies published in the English language were considered. Methodological quality was assessed using the Qualitative Assessment and Review Instrument developed by the Joanna Briggs Institute. Qualitative findings were extracted using the Joanna Briggs Institute Qualitative Assessment and Review Instrument. Qualitative research findings were pooled using a pragmatic meta-aggregative approach and the Joanna Briggs Institute Qualitative Assessment and Review Instrument software. This review included 21 publications from 18 research studies, representing a wide range of countries and healthcare settings. There were 245 findings which were aggregated into 12 categories and five synthesized findings. 1. Nurses/midwives are supportive of provider-initiated HIV testing and counseling if it is perceived to enhance patient care and to align with perceived professional roles. 2. Nurses'/midwives' ability to perform provider-initiated HIV testing and counseling well requires an appropriate infrastructure and adequate human and material resources. 3. At the organizational level, nurses'/midwives' engagement with provider-initiated HIV testing and counseling is facilitated by an inclusive management structure, alongside the provision of ongoing training and clinical supervision. Provider-initiated HIV testing and counseling is hindered by difficulties in fitting it into existing workloads and routines. 4. Nurses/midwives perceive that good quality care in provider-initiated HIV testing and counseling involves finding a balance between public health needs and individual patient needs. Good care requires time and the ability to apply a patient centred approach. 5. The emotional work involved in provider-initiated HIV testing and counseling can be stressful. Nurses/Midwives may require support to deal with complex moral and ethical issues. This review shows that provider-initiated HIV testing and counseling is supported by nurses/midwives who strive to implement it according to principles of good care and a patient centered approach. Nurses/midwives face multiple operational, infra-structural, resource and ethical challenges in the implementation of provider-initiated HIV testing and counseling. The implementation process for provider-initiated HIV testing and counseling would benefit from using a quality improvement framework. Nurses/midwives undertaking provider-initiated HIV testing and counseling require management support, ongoing training and adequate infrastructure/resources. Additional guidance is required on legal/ethical issues in testing of children and in third party disclosure. Operational research is required to determine an optimal skill mix and optimal methods of integrating provider-initiated HIV testing and counseling into existing work routines. The Joanna Briggs Institute.

Care Cascade for targeted tuberculosis testing and linkage to Care in Homeless Populations in the United States: a meta-analysis.

PubMed

Parriott, Andrea; Malekinejad, Mohsen; Miller, Amanda P; Marks, Suzanne M; Horvath, Hacsi; Kahn, James G

2018-04-12

Homelessness increases the risk of tuberculosis (TB) disease and latent TB infection (LTBI), but persons experiencing homelessness often lack access to testing and treatment. We assessed the yield of TB testing and linkage to care for programs targeting homeless populations in the United States. We conducted a comprehensive search of peer-reviewed and grey literature, adapting Cochrane systematic review methods. Two reviewers independently assessed study eligibility and abstracted key data on the testing to care cascade: number of persons reached, recruited for testing, tested for LTBI, with valid test results, referred to follow-up care, and initiating care. We used random effects to calculate pooled proportions and 95% confidence intervals (CI) of persons retained in each step via inverse-variance weighted meta-analysis, and cumulative proportions as products of adjacent step proportions. We identified 23 studies published between 1986 and 2014, conducted in 12 states and 15 cities. Among studies using tuberculin skin tests (TST) we found that 93.7% (CI 72.4-100%) of persons reached were recruited, 97.9% (89.3-100%) of those recruited had tests placed, 85.5% (78.6-91.3%) of those with tests placed returned for reading, 99.9% (99.6-100%) of those with tests read had valid results, and 24.7% (21.0-28.5%) with valid results tested positive. All persons testing positive were referred to follow-up care, and 99.8% attended at least one session of follow-up care. Heterogeneity was high for most pooled proportions. For a hypothetical cohort of 1000 persons experiencing homelessness reached by a targeted testing program using TST, an estimated 917 were tested, 194 were positive, and all of these initiated follow-up care. Targeted TB testing of persons experiencing homelessness appears effective in detecting LTBI and connecting persons to care and potential treatment. Future evaluations should assess diagnostic use of interferon gamma release assays and completion of treatment, and costs of testing and treatment.

Assessing Situational Awareness in Task Force XXI.

DTIC Science & Technology

1997-06-01

information dominance over the enemy and that units equipped with greater situational awareness will fight more successfully than units without the added capability. In an effort to test this hypothesis the Army conducted an Advanced Warfighter Experiment (AWE) which began at Ft. Hood, TX and culminated in a focused rotation at the National Training Center, Ft. Irwin, CA. Although many initiatives in the area of information dominance were tested in the AWE, the centerpiece of the program was a test case unit designated as Task Force Twenty-One (TF

Cyclic Failure Mechanisms of Thermal and Environmental Barrier Coating Systems Under Thermal Gradient Test Conditions

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Lee, Kang N.; Miller, Robert A.

2002-01-01

Plasma-sprayed ZrO2-8wt%Y2O3 and mullite+BSAS/Si multilayer thermal and environmental barrier coating (TBC-EBC) systems on SiC/SiC ceramic matrix composite (CMC) substrates were thermally cyclic tested under high thermal gradients using a laser high-heat-flux rig in conjunction with furnace exposure in water-vapor environments. Coating sintering and interface damage were assessed by monitoring the real-time thermal conductivity changes during the laser heat-flux tests and by examining the microstructural changes after exposure. Sintering kinetics of the coating systems were also independently characterized using a dilatometer. It was found that the coating failure involved both the time-temperature dependent sintering and the cycle frequency dependent cyclic fatigue processes. The water vapor environments not only facilitated the initial coating conductivity increases due to enhanced sintering and interface reaction, but also promoted later conductivity reductions due to the accelerated coating cracking and delamination. The failure mechanisms of the coating systems are also discussed based on the cyclic test results and are correlated to the sintering and thermal stress behavior under the thermal gradient test conditions.

Series-Bosch Technology for Oxygen Recovery During Lunar or Martian Surface Missions

NASA Technical Reports Server (NTRS)

Abney, Morgan B.; Mansell, J. Matthew; Rabenberg, Ellen; Stanley, Christine M.; Edmunson, Jennifer; Alleman, James E.; Chen, Kevin; Dumez, Sam

2014-01-01

Long-duration surface missions to the Moon or Mars will require life support systems that maximize resource recovery to minimize resupply from Earth. To address this need, NASA previously proposed a Series-Bosch (S-Bosch) oxygen recovery system, based on the Bosch process, which can theoretically recover 100% of the oxygen from metabolic carbon dioxide. Bosch processes have the added benefits of the potential to recover oxygen from atmospheric carbon dioxide and the use of regolith materials as catalysts, thereby eliminating the need for catalyst resupply from Earth. In 2012, NASA completed an initial design for an S-Bosch development test stand that incorporates two catalytic reactors in series including a Reverse Water-Gas Shift (RWGS) Reactor and a Carbon Formation Reactor (CFR). In 2013, fabrication of system components, with the exception of a CFR, and assembly of the test stand was initiated. Stand-alone testing of the RWGS reactor was completed to compare performance with design models. Continued testing of Lunar and Martian regolith simulants provided sufficient data to design a CFR intended to utilize these materials as catalysts. Finally, a study was conducted to explore the possibility of producing bricks from spent regolith catalysts. The results of initial demonstration testing of the RWGS reactor, results of continued catalyst performance testing of regolith simulants, and results of brick material properties testing are reported. Additionally, design considerations for a regolith-based CFR are discussed.

Series-Bosch Technology for Oxygen Recovery During Lunar or Martian Surface Missions

NASA Technical Reports Server (NTRS)

Abney, Morgan B.; Mansell, James M.; Stanley, Christine; Edmunson, Jennifer; Dumez, Samuel; Chen, Kevin; Alleman, James E.

2014-01-01

Long-duration surface missions to the Moon or Mars will require life support systems that maximize resource recovery to minimize resupply from Earth. To address this need, NASA previously proposed a Series-Bosch (S-Bosch) oxygen recovery system, based on the Bosch process, which can theoretically recover 100% of the oxygen from metabolic carbon dioxide. Bosch processes have the added benefits of the potential to recover oxygen from atmospheric carbon dioxide and the use of regolith materials as catalysts, thereby eliminating the need for catalyst resupply from Earth. In 2012, NASA completed an initial design for an S-Bosch development test stand that incorporates two catalytic reactors in series including a Reverse Water-Gas Shift (RWGS) Reactor and a Carbon Formation Reactor (CFR). In 2013, fabrication of system components, with the exception of a CFR, and assembly of the test stand was initiated. Stand-alone testing of the RWGS reactor was completed to compare performance with design models. Continued testing of Lunar and Martian regolith simulants provided sufficient data to design a CFR intended to utilize these materials as catalysts. Finally, a study was conducted to explore the possibility of producing bricks from spend regolith catalysts. The results of initial demonstration testing of the RWGS reactor, results of continued catalyst performance testing of regolith simulants, and results of brick material properties testing are reported. Additionally, design considerations for a regolith-based CFR are discussed.

Creep Strain and Strain Rate Response of 2219 Al Alloy at High Stress Levels

NASA Technical Reports Server (NTRS)

Taminger, Karen M. B.; Wagner, John A.; Lisagor, W. Barry

1998-01-01

As a result of high localized plastic deformation experienced during proof testing in an International Space Station connecting module, a study was undertaken to determine the deformation response of a 2219-T851 roll forging. After prestraining 2219-T851 Al specimens to simulate strains observed during the proof testing, creep tests were conducted in the temperature range from ambient temperature to 107 C (225 F) at stress levels approaching the ultimate tensile strength of 2219-T851 Al. Strain-time histories and strain rate responses were examined. The strain rate response was extremely high initially, but decayed rapidly, spanning as much as five orders of magnitude during primary creep. Select specimens were subjected to incremental step loading and exhibited initial creep rates of similar magnitude for each load step. Although the creep rates decreased quickly at all loads, the creep rates dropped faster and reached lower strain rate levels for lower applied loads. The initial creep rate and creep rate decay associated with primary creep were similar for specimens with and without prestrain; however, prestraining (strain hardening) the specimens, as in the aforementioned proof test, resulted in significantly longer creep life.

Environmental control medical support team

NASA Technical Reports Server (NTRS)

Crump, William J.; Kilgore, Melvin V., Jr.

1988-01-01

The activities conducted in support of the Environmental Control and Life Support Team during December 7, 1987 through September 30, 1988 are summarized. The majority of the ongoing support has focused on the ECLSS area. Through a series of initial meetings with the ECLSS team and technical literature review, an initial list of critical topics was developed. Subtasks were then identified or additional related tasks received as action items from the ECLSS group meetings. Although most of the efforts focused on providing MSFC personnel with information regarding specific questions and problems related to ECLSS issues, other efforts regarding identifying an ECLSS Medical Support Team and constructing data bases of technical information were also initiated and completed. The specific tasks are as follows: (1) Provide support to the mechanical design and integration of test systems as related to microbiological concerns; (2) Assist with design of Human Subjects Test Protocols; (3) Interpretation and recommendations pertaining to air/water quality requirements; (4) Assist in determining the design specifications required as related to the Technical Demonstration Program; (5) Develop a data base of all microorganisms recovered from previous subsystem testing; (6) Estimates of health risk of individual microbes to test subjects; (7) Assist with setting limits for safety of test subjects; (8) Health monitoring of test subjects; (9) Assist in the preparation of test plans; (10) Assist in the development of a QA/QC program to assure the validity, accuracy and precision of the analyses; and (11) Assist in developing test plans required for future man in the loop testing.

Advanced Study for Active Noise Control in Aircraft (ASANCA)

NASA Technical Reports Server (NTRS)

Borchers, Ingo U.; Emborg, Urban; Sollo, Antonio; Waterman, Elly H.; Paillard, Jacques; Larsen, Peter N.; Venet, Gerard; Goeransson, Peter; Martin, Vincent

1992-01-01

Aircraft interior noise and vibration measurements are included in this paper from ground and flight tests. In addition, related initial noise calculations with and without active noise control are conducted. The results obtained to date indicate that active noise control may be an effective means for reducing the critical low frequency aircraft noise.

Work Social Supports, Role Stressors, and Work-Family Conflict: The Moderating Effect of Age

ERIC Educational Resources Information Center

Matthews, Russell A.; Bulger, Carrie A.; Barnes-Farrell, Janet L.

2010-01-01

The current study examined whether important distinctions are masked if participant age is ignored when modeling relationships among constructs associated with the work-family interface. An initial omnibus model of social support, work role stressors, and work-family conflict was tested. Multiple groups analyses were then conducted to investigate…

Assessment of Relationship-Specific Incentive and Threat Sensitivities: Predicting Satisfaction and Affect in Adult Intimate Relationships

ERIC Educational Resources Information Center

Laurenceau, Jean-Philippe; Kleinman, Brighid M.; Kaczynski, Karen J.; Carver, Charles S.

2010-01-01

Self-report scales assessing relationship-specific incentive and threat sensitivity were created. Initial tests of factor structure and associations with relationship quality were conducted in a sample of persons in intimate relationships (Study 1). Associations with conceptually related measures were examined to determine convergent and…

Marital Happiness and Psychological Well-Being across the Life Course

ERIC Educational Resources Information Center

Kamp Dush, Claire M.; Taylor, Miles G.; Kroeger, Rhiannon A.

2008-01-01

Using data from six waves of the Study of Marital Instability over the Life Course (N = 1,998), we conducted a latent class analysis to test for distinct marital happiness trajectories. We found three distinct marital happiness trajectories: low, middle, and high happiness. Initial levels of life happiness were strongly associated with membership…

Can Heterosexism Harm Organizations? Predicting the Perceived Organizational Citizenship Behaviors of Gay and Lesbian Employees

ERIC Educational Resources Information Center

Brenner, Bradley R.; Lyons, Heather Z.; Fassinger, Ruth E.

2010-01-01

An initial test and validation of a model predicting perceived organizational citizenship behaviors (OCBs) of lesbian and gay employees were conducted using structural equation modeling. The proposed structural model demonstrated acceptable goodness of ft and structural invariance across 2 samples (ns = 311 and 295), which suggested that…

Improving Attachments of Non-Invasive (Type III) Electronic Data Loggers to Cetaceans

DTIC Science & Technology

2013-09-30

logged using a netbook and USB analog to digital converter. Initial testing of the SSSCup was conducted on a common dolphin (Delphinus delphis) cadaver...cell and five pressure sensors (four to measure internal cup pressure and one for atmospheric pressure). Sensor data are logged using a netbook and

40 CFR 62.14650 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2010 CFR

2010-07-01

... part 60, Appendix A must be used for gas composition analysis, including measurement of oxygen...) All pollutant concentrations, except for opacity, must be adjusted to 7 percent oxygen using Equation... adjusted to 7 percent oxygen; Cmeas = pollutant concentration measured on a dry basis; (20.9−7) = 20.9...

40 CFR 62.14650 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2011 CFR

2011-07-01

... part 60, Appendix A must be used for gas composition analysis, including measurement of oxygen...) All pollutant concentrations, except for opacity, must be adjusted to 7 percent oxygen using Equation... adjusted to 7 percent oxygen; Cmeas = pollutant concentration measured on a dry basis; (20.9−7) = 20.9...

Measuring the Institutional Stance on Matters of Student Conduct.

ERIC Educational Resources Information Center

Seligman, Richard

This study is concerned with the initial testing of a questionnaire designed to examine student discipline policies in terms of student perception of goals and objectives, scope, procedures, and sanctions. "Institutional Procedures in Colleges and Universities" (IPCU), the questionnaire, containing 45 items, was sent to students and deans at 5…

Content Analysis of Measures for Identification of Elder Abuse.

ERIC Educational Resources Information Center

Sengstock, Mary C.; And Others

Measures designed to detect elder abuse lack uniformity as a result of having been designed in isolation. To develop and test a uniform index for the identification of elder abuse victims, an analysis of existing abuse identification instruments was conducted. Initially, seven elder abuse identification measures were content analyzed, resulting in…

Preliminary Results of an Experimental Investigation of the Qu Superconducting Heat Pipe

NASA Technical Reports Server (NTRS)

Blackmon, James B.; Entrekin, Sean F.

2006-01-01

This note on preliminary results of our evaluation of the so-called Qu Tube is prompted in part by recent concerns expressed to the authors by some researchers regarding the performance characteristics of the superconducting, solid-state heat pipe as described in the patents, or on the company's websites. Briefly, the company's claims include: a new type of heat transfer mechanism that is a form of solid state thermal superconductivity, which results in an effective thermal conductivity of the order of tens of thousands of times that of an equivalent solid silver bar, or, tens to hundreds of times that of liquid - vapor heat pipes. The company's website also refers to tests conducted by Stanford Research Institute that substantiate these claims, but the report is apparently not publicly available. We are conducting an investigation of the Qu Tube under a NASA Grant, and in general find that these claims have merit, but our study is not yet complete. We present some of our preliminary results in part to show that it would not be imprudent to conduct such studies, especially for possible future applications requiring exceptional thermal management performance capabilities. Working with HiTek Services, we originally acquired several Qu Tubes, including 17" long, 5/16" diameter copper tubes, one that is 7 7/8" long, 3/16" diameter, and one that is 4" long, 1" diameter. We subjected the smaller tubes to various exploratory tests, including a transient test with electrical band heaters, boiling water tests, and a series of steady state tests with electrical band heaters heating one end with free convective cooling along the remainder of the length. All results indicate a very high thermal conductivity, but the length of these tubes limited our ability to obtain accurate data on temperature gradients, necessary to determine the effective thermal conductivity. We then acquired nine Qu Tubes that are 10' long, 5/16" diameter, and we have recently conducted initial tests, which further support the claims of exceptional thermal conductivity.

Evaluation of pyrolysis and arc tracking on candidate wire insulation designs for space applications

NASA Technical Reports Server (NTRS)

Stueber, Thomas J.; Hrovat, Kenneth

1994-01-01

The ability of wire insulation materials and constructions to resist arc tracking was determined and the damage caused by initial arcing and restrike events was assessed. Results of arc tracking tests on various insulation constructions are presented in view-graph format. Arc tracking tests conducted on Champlain, Filotex, and Teledyne Thermatics indicate the Filotex is least likely to arc track. Arc tracking occurs more readily in air than it does in vacuum.

Stress Hormone Enhancement of OP-Induced Neuroinflammation as an Animal Model of GWI: The Role of Toll-like Receptors and Plasticity

DTIC Science & Technology

2017-09-01

water maze hippocampus neurogenesis synaptic plasticity neurotrophins corticosterone priming inflammatory mediators gene expression...remaining studies conducted on the project at the University of Illinois at Chicago. The Morris water maze was the initial behavioral test of spatial...experience with this paradigm. In this test a mouse must learn the location of an escape platform by swimming in a pool of water at room temperature

Development of an Acetate-Fed or Sugar-Fed Microbial Power Generator for Military Bases

DTIC Science & Technology

2011-01-01

quarter. We tested graphite and stainless steel as anode materials for ARB growth, showing the greater suitability of carbon fibers as anode material...microbial electrolysis cells (MECs) with graphite rods and stainless steel meshes as anodes to select the optimum material for use in MFC modules to...be tested in the future. We selected meshes made from 316-grade stainless steel for these initial studies. We conducted several trials with the MECs

Hairy carbon electrodes studied by cyclic voltammetry and battery discharge testing

NASA Technical Reports Server (NTRS)

Chung, Deborah D. L.; Shui, Xiaoping; Frysz, Christine A.

1993-01-01

Hairy carbon is a new material developed by growing submicron carbon filaments on conventional carbon substrates. Typical substrate materials include carbon black, graphite powder, carbon fibers, and glassy carbon. A catalyst is used to initiate hair growth with carbonaceous gases serving as the carbon source. To study the electrochemical behavior of hairy carbons, cyclic voltammetry (CV) and discharge testing were conducted. In both cases, hairy carbon results surpassed those of the substrate material alone.

Theoretical considerations of some nonlinear aspects of hypersonic panel flutter

NASA Technical Reports Server (NTRS)

Mcintosh, S. C., Jr.

1974-01-01

A research project to analyze the effects of hypersonic nonlinear aerodynamic loading on panel flutter is reported. The test equipment and procedures for conducting the tests are explained. The effects of aerodynamic linearities on stability were evaluated by determining constant-initial-energy amplitude-sensitive stability boundaries and comparing them with the corresponding linear stability boundaries. An attempt to develop an alternative method of analysis for systems where amplitude-sensitive instability is possible is presented.

The RAILER System for Maintenance Management of U.S. Army Railroad Networks: RAILER 1 Description and Use

DTIC Science & Technology

1988-09-01

the report. Field Testing Specific aspects of field procedures have been tested at Fort Devens , MA, and at the Consolidated Rail Corporation (Conrail...days of formalized training on the system, both field proce- dures and computer operations, were conducted by USA-CERL at Fort Devens , MA. Attendees...included representatives from TSC, Fort Devens , FORSCOM, and the T.K. Dyer Corp. Initial Track Segmenting and Component Identification The office work

Serum potassium monitoring for users of ethinyl estradiol/drospirenone taking medications predisposing to hyperkalemia: physician compliance and survey of knowledge and attitudes.

PubMed

Mona Eng, Patricia; Seeger, John D; Loughlin, Jeanne; Oh, Kelly; Walker, Alexander M

2007-02-01

Yasmin-28 [ethinyl estradiol 0.03 mg/drospirenone 3 mg (EE/DRSP)] contains drospirenone, a progestin component that possesses antimineralocorticoid activity with a potassium-sparing diuretic effect similar to that in spironolactone. Product labeling recommends potassium monitoring in the first month of use for women concurrently receiving medication that may increase serum potassium. We evaluated compliance with this recommendation by measuring monitoring around the date of oral contraceptive (OC) initiation in women who received EE/DRSP while being treated with medications predisposing to hyperkalemia and in similar women who received other OCs. Because preliminary analyses indicated incomplete compliance, we surveyed physicians who prescribed EE/DRSP to women receiving drugs predisposing to hyperkalemia on their knowledge and attitudes with regard to the recommendation. We conducted this study using data from the Ingenix Research Datamart, which includes insurance claims for reimbursement for medical services and prescription medications for approximately 8,000,000 members of a large nationally dispersed health plan. We used claims for pharmacy dispensings of prescription medications to identify all women aged 10-59 years old who initiated EE/DRSP or other OCs during the first 3 years of EE/DRSP availability (July 2001 to June 2004). The frequency of potassium monitoring was measured by identifying claims for serum potassium tests. We conducted a telephone survey of 58 physicians who had prescribed EE/DRSP up to June 2003 to women who received concomitant hyperkalemic drugs. Although potassium monitoring was generally more frequent among EE/DRSP initiators receiving concomitant hyperkalemic drugs than among other OC initiators receiving similar medications, only 40% of 466 EE/DRSP initiators with concurrent hyperkalemic treatment had potassium tests. More than 98% of surveyed physicians were aware of the potassium-sparing property of EE/DRSP. Compared with physicians whose patients had potassium tests, physicians of patients without such tests were more likely to disagree with the recommendation for users of angiotensin-converting enzyme inhibitors, angiotensin II receptor antagonists, heparin and nonsteroidal anti-inflammatory drugs. Patient barriers and health plan restrictions were other factors possibly contributing to noncompliance. This study demonstrates incomplete physician compliance with a labeling recommendation of potassium monitoring for initiators of EE/DRSP receiving concomitant therapy predisposing to hyperkalemia. The limited compliance was likely due to a combination of selective physician acceptance of the recommendations and specific patient and health plan barriers to testing.

Development of instrument for assessing students’ critical and creative thinking ability

NASA Astrophysics Data System (ADS)

Herpiana, R.; Rosidin, U.

2018-01-01

The purpose of this study was to develop instruments to measure critical thinking ability and creative students in the topics of physics simple harmonic motion. The research method used was research development with application of procedures including research and data collection, planning, and initial product development. The participants of the study were thirty-four tenth grade students and five physics teachers of physics who were selected randomly from schools in the province of Lampung. The data collected by using test and analyzed in quantitative descriptive. Initial data showed that students’ critical and creative thinking ability were still low and instruments to assess students’ critical thinking skills and creative students was not yet available. Most of assessment conducted focused on memorization. Thus, the researchers developed a draft of instrument in the form of the test description based on criteria that encouraged students’ activity in understanding the concepts, strategies and decision/solution in dealing with problems. The development of the instrument was conducted considering real-world phenomena in the form of pictures and stories, description of the situation, and verbal presentation.

Development of a MEMS device for acoustic emission testing

NASA Astrophysics Data System (ADS)

Ozevin, Didem; Pessiki, Stephen P.; Jain, Akash; Greve, David W.; Oppenheim, Irving J.

2003-08-01

Acoustic emission testing is an important technology for evaluating structural materials, and especially for detecting damage in structural members. Significant new capabilities may be gained by developing MEMS transducers for acoustic emission testing, including permanent bonding or embedment for superior coupling, greater density of transducer placement, and a bundle of transducers on each device tuned to different frequencies. Additional advantages include capabilities for maintenance of signal histories and coordination between multiple transducers. We designed a MEMS device for acoustic emission testing that features two different mechanical types, a hexagonal plate design and a spring-mass design, with multiple detectors of each type at ten different frequencies in the range of 100 kHz to 1 MHz. The devices were fabricated in the multi-user polysilicon surface micromachining (MUMPs) process and we have conducted electrical characterization experiments and initial experiments on acoustic emission detection. We first report on C(V) measurements and perform a comparison between predicted (design) and measured response. We next report on admittance measurements conducted at pressures varying from vacuum to atmospheric, identifying the resonant frequencies and again providing a comparison with predicted performance. We then describe initial calibration experiments that compare the performance of the detectors to other acoustic emission transducers, and we discuss the overall performance of the device as a sensor suite, as contrasted to the single-channel performance of most commercial transducers.

Counselors' Clinical Use of Definitive Drug Testing Results in Their Work with Substance-Use Clients: a Qualitative Study.

PubMed

Rzetelny, Adam; Zeller, Barbara; Miller, Nicholas; City, Kathy Egan; Kirsh, Kenneth L; Passik, Steven D

We conducted a psychotherapeutic examination of the use of definitive drug testing (liquid chromatography with tandem mass spectrometry) in the treatment of substance use disorders (SUD). Employing a generic qualitative method (Caelli et al. in International Journal of Qualitative Methods, 2 (2), 2003; Merriam, 2009) we asked SUD counselors to provide narratives about cases where drug testing had revealed new or unexpected information about clients' drug-taking behaviors. Semi-structured interviews with 12 SUD counselors were conducted by phone and analyzed for themes derived from the literature. These counselors reported many new positive drug tests in clients previously believed to be adherent with treatment. Key themes assessed in counselors' narratives included initial client denial that was often followed by later acknowledgement of relapse and increased motivation, at times presenting new opportunities for clients to engage in treatment and enhance the therapeutic alliance. These results suggest that definitive drug testing can be used in a non-stigmatizing and therapeutic manner.

Synergistic Development, Test, and Qualification Approaches for the Ares I and V Launch Vehicles

NASA Technical Reports Server (NTRS)

Cockrell, Charles E.; Taylor, James L.; Patterson, Alan; Stephens, Samuel E.; Tuma, Margaret; Bartolotta, Paul; Huetter, Uwe; Kaderback, Don; Goggin, David

2009-01-01

The U.S. National Aeronautics and Space Administration (NASA) initiated plans to develop the Ares I and Ares V launch vehicles in 2005 to meet the mission objectives for future human exploration of space. Ares I is designed to provide the capability to deliver the Orion crew exploration vehicle (CEV) to low-Earth orbit (LEO), either for docking to the International Space Station (ISS) or docking with an Earth departure stage (EDS) and lunar lander for transit to the Moon. Ares V provides the heavy-lift capability to deliver the EDS and lunar lander to orbit. An integrated test plan was developed for Ares I that includes un-crewed flight validation testing and ground testing to qualify structural components and propulsion systems prior to operational deployment. The overall test program also includes a single development test flight conducted prior to the Ares I critical design review (CDR). Since the Ares V concept was formulated to maximize hardware commonality between the Ares V and Ares I launch vehicles, initial test planning for Ares V has considered the extensibility of test approaches and facilities from Ares I. The Ares V test plan was part of a successful mission concept review (MCR) in 2008.

A New Method for a Virtue-Based Responsible Conduct of Research Curriculum: Pilot Test Results.

PubMed

Berling, Eric; McLeskey, Chet; O'Rourke, Michael; Pennock, Robert T

2018-02-03

Drawing on Pennock's theory of scientific virtues, we are developing an alternative curriculum for training scientists in the responsible conduct of research (RCR) that emphasizes internal values rather than externally imposed rules. This approach focuses on the virtuous characteristics of scientists that lead to responsible and exemplary behavior. We have been pilot-testing one element of such a virtue-based approach to RCR training by conducting dialogue sessions, modeled upon the approach developed by Toolbox Dialogue Initiative, that focus on a specific virtue, e.g., curiosity and objectivity. During these structured discussions, small groups of scientists explore the roles they think the focus virtue plays and should play in the practice of science. Preliminary results have shown that participants strongly prefer this virtue-based model over traditional methods of RCR training. While we cannot yet definitively say that participation in these RCR sessions contributes to responsible conduct, these pilot results are encouraging and warrant continued development of this virtue-based approach to RCR training.

Initial group dietary education compared to individual education in gestational diabetes mellitus management: Do outcomes differ?

PubMed

Barnes, Robyn A; Ross, Glynis P; Jalaludin, Bin B; Flack, Jeff R

2018-03-29

To assess the effectiveness of Initial Group versus Initial Individual GDM dietary education in terms of insulin requirements and pregnancy outcomes. A retrospective audit of clinical data was conducted where English speaking women who received initial education in a group setting (01-2-2012 to 01-2-2014) (Group), were compared to women who received initial individual education with a dietitian (1-2-2010 to 31-1-2012) (Individual), all followed by one individual dietitian appointment. The same dietary information was provided in both settings. Data collected included: attendance rates, insulin requirements, maternal weight gain, and rates of adverse birth outcomes. Data were compared by t-test or Chi-squared test. Multivariable logistic regression analysis was conducted to determine independent predictors of insulin therapy. Of 743 women; (362 Group and 381 Individual), Group women had a lower HbA1c at GDM diagnosis 5.3 ± 0.6% versus 5.5 ± 0.5% (34 ± 6.6 mmol/mol versus 37 ± 5.5 mmol/mol p < 0.0001). There were no other differences in baseline characteristics. More Group women required insulin (42.0% versus 34.6%, p = 0.048). Group education was found to be an independent predictor of insulin therapy (OR = 1.9 [1.29, 2.75] p < 0.001). Despite adjusting for all known potential confounders, unlike Individual education, Group education remained a significant predictor of insulin therapy (but resulted in similar therapeutic and pregnancy outcomes to Individual education). Copyright © 2018 Elsevier B.V. All rights reserved.

Dynamic Fracture Initiation Toughness at Elevated Temperatures With Application to the New Generation of Titanium Aluminide Alloys. Chapter 8

NASA Technical Reports Server (NTRS)

Shazly, Mostafa; Prakash, Vikas; Draper, Susan; Shukla, Arun (Editor)

2006-01-01

Recently, a new generation of titanium aluminide alloy, named Gamma-Met PX, has been developed with better rolling and post-rolling characteristics. I'revious work on this alloy has shown the material to have higher strengths at room and elevated temperatures when compared with other gamma titanium aluminides. In particular, this new alloy has shown increased ductility at elevated temperatures under both quasi-static and high strain rate uniaxial compressive loading. However, its high strain rate tensile ductility at room and elevated temperatures is limited to approx. 1%. In the present chapter, results of a study to investigate the effects of loading rate and test temperature on the dynamic fracture initiation toughness in Gamma-Met PX are presented. Modified split Hopkinson pressure bar was used along with high-speed photography to determine the crack initiation time. Three-point bend dynamic fracture experiments were conducted at impact speeds of approx. 1 m/s and tests temperatures of up-to 1200 C. The results show that thc dynamic fracture initiation toughness decreases with increasing test temperatures beyond 600 C. Furthermore, thc effect of long time high temperature air exposure on the fracture toughness was investigated. The dynamic fracture initiation toughness was found to decrease with increasing exposure time. The reasons behind this drop are analyzed and discussed.

Institute for Clean Energy Technology Mississippi State University NSR&D Aged HEPA Filter Study Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacks, Robert; Stormo, Julie; Rose, Coralie

Data have demonstrated that filter media lose tensile strength and the ability to resist the effects of moisture as a function of age. Testing of new and aged filters needs to be conducted to correlate reduction of physical strength of HEPA media to the ability of filters to withstand upset conditions. Appendix C of the Nuclear Air Cleaning Handbook provides the basis for DOE’s HEPA filter service life guidance. However, this appendix also points out the variability of data, and it does not correlate performance of aged filters to degradation of media due to age. Funding awarded by NSR&D tomore » initiate full-scale testing of aged HEPA filters addresses the issue of correlating media degradation due to age with testing of new and aged HEPA filters under a generic design basis event set of conditions. This funding has accelerated the process of describing this study via: (1) establishment of a Technical Working Group of all stakeholders, (2) development and approval of a test plan, (3) development of testing and autopsy procedures, (4) acquiring an initial set of aged filters, (5) testing the initial set of aged filters, and (6) developing the filter test report content for each filter tested. This funding was very timely and has moved the project forward by at least three years. Activities have been correlated with testing conducted under DOE-EM funding for evaluating performance envelopes for AG-1 Section FC Separator and Separatorless filters. This coordination allows correlation of results from the NSR&D Aged Filter Study with results from testing new filters of the Separator and Separatorless Filter Study. DOE-EM efforts have identified approximately 100 more filters of various ages that have been stored under Level B conditions. NSR&D funded work allows a time for rigorous review among subject matter experts before moving forward with development of the testing matrix that will be used for additional filters. The NSR&D data sets are extremely valuable in as much as establishing a selfimproving, NQA-1 program capable of advancing the service lifetime study of HEPA filters. The data and reports are available for careful and critical review by subject matter experts before the next set of filters is tested and can be found in the appendices of this final report. NSR&D funds have not only initiated the Aged HEPA Filter Study alluded to in Appendix C of the NACH, but have also enhanced the technical integrity and effectiveness of all of the follow-on testing for this long-term study.« less

Static tensile and tensile creep testing of four boron nitride coated ceramic fibers at elevated temperatures

NASA Technical Reports Server (NTRS)

Coguill, Scott L.; Adams, Donald F.; Zimmerman, Richard S.

1989-01-01

Six types of uncoated ceramic fibers were static tensile and tensile creep tested at various elevated temperatures. Three types of boron nitride coated fibers were also tested. Room temperature static tensile tests were initially performed on all fibers, at gage lengths of 1, 2, and 4 inches, to determine the magnitude of end effects from the gripping system used. Tests at one elevated temperature, at gage lengths of 8 and 10 inches, were also conducted, to determine end effects at elevated temperatures. Fiber cross sectional shapes and areas were determined using scanning electron microscopy. Creep testing was typically performed for 4 hours, in an air atmosphere.

Feasibility of Conducting J-2X Engine Testing at the Glenn Research Center Plum Brook Station B-2 Facility

NASA Technical Reports Server (NTRS)

Schafer, Charles F.; Cheston, Derrick J.; Worlund, Armis L.; Brown, James R.; Hooper, William G.; Monk, Jan C.; Winstead, Thomas W.

2008-01-01

A trade study of the feasibility of conducting J-2X testing in the Glenn Research Center (GRC) Plum Brook Station (PBS) B-2 facility was initiated in May 2006 with results available in October 2006. The Propulsion Test Integration Group (PTIG) led the study with support from Marshall Space Flight Center (MSFC) and Jacobs Sverdrup Engineering. The primary focus of the trade study was on facility design concepts and their capability to satisfy the J-2X altitude simulation test requirements. The propulsion systems tested in the B-2 facility were in the 30,000-pound (30K) thrust class. The J-2X thrust is approximately 10 times larger. Therefore, concepts significantly different from the current configuration are necessary for the diffuser, spray chamber subsystems, and cooling water. Steam exhaust condensation in the spray chamber is judged to be the key risk consideration relative to acceptable spray chamber pressure. Further assessment via computational fluid dynamics (CFD) and other simulation capabilities (e.g. methodology for anchoring predictions with actual test data and subscale testing to support investigation.

Functional Analysis of Problem Behavior: A Systematic Approach for Identifying Idiosyncratic Variables

PubMed Central

Roscoe, Eileen M.; Schlichenmeyer, Kevin J.; Dube, William V.

2015-01-01

When inconclusive functional analysis (FA) outcomes occur, a number of modifications have been made to enhance the putative establishing operation or consequence associated with behavioral maintenance. However, a systematic method for identifying relevant events to test during modified FAs has not been evaluated. The purpose of this study was to develop and evaluate a technology for systematically identifying events to test in a modified FA after an initial FA led to inconclusive outcomes. Six individuals whose initial FA showed little or no responding or high levels only in the control condition participated. An indirect assessment (IA) questionnaire developed for identifying idiosyncratic variables was administered, and a descriptive analysis (DA) was conducted. Results from the IA only or a combination of the IA and DA were used to inform modified FA test and control conditions. Conclusive FA outcomes were obtained with five of the six participants during the modified FA phase. PMID:25930176

Failure analysis of solid rocket apogee motors

NASA Technical Reports Server (NTRS)

Martin, P. J.

1972-01-01

The analysis followed five selected motors through initial design, development, test, qualification, manufacture, and final flight reports. An audit was conducted at the manufacturing plants to complement the literature search with firsthand observations of the current philosophies and practices that affect reliability of the motors. A second literature search emphasized acquisition of spacecraft and satellite data bearing on solid motor reliability. It was concluded that present practices at the plants yield highly reliable flight hardware. Reliability can be further improved by new developments of aft-end bonding and initiator/igniter nondestructive test methods, a safe/arm device, and an insulation formulation. Minimum diagnostic instrumentation is recommended for all motor flights. Surplus motors should be used in margin testing. Criteria should be established for pressure and zone curing. The motor contractor should be represented at launch. New design analyses should be made of stretched motors and spacecraft/motor pairs.

Dynamics of backlight luminance for using smartphone in dark environment

NASA Astrophysics Data System (ADS)

Na, Nooree; Jang, Jiho; Suk, Hyeon-Jeong

2014-02-01

This study developed dynamic backlight luminance, which gradually changes as time passes for comfortable use of a smartphone display in a dark environment. The study was carried out in two stages. In the first stage, a user test was conducted to identify the optimal luminance by assessing the facial squint level, subjective glare evaluation, eye blink frequency and users' subjective preferences. Based on the results of the user test, the dynamics of backlight luminance was designed. It has two levels of luminance: the optimal level for initial viewing to avoid sudden glare or fatigue to users' eyes, and the optimal level for constant viewing, which is comfortable, but also bright enough for constant reading of the displayed material. The luminance for initial viewing starts from 10 cd/m2, and it gradually increases to 40 cd/m2 for users' visual comfort at constant viewing for 20 seconds; In the second stage, a validation test on dynamics of backlight luminance was conducted to verify the effectiveness of the developed dynamics. It involving users' subjective preferences, eye blink frequency, and brainwave analysis using the electroencephalogram (EEG) to confirm that the proposed dynamic backlighting enhances users' visual comfort and visual cognition, particularly for using smartphones in a dark environment.

Creep Crack Initiation and Growth Behavior for Ni-Base Superalloys

NASA Astrophysics Data System (ADS)

Nagumo, Yoshiko; Yokobori, A. Toshimitsu, Jr.; Sugiura, Ryuji; Ozeki, Go; Matsuzaki, Takashi

The structural components which are used in high temperature gas turbines have various shapes which may cause the notch effect. Moreover, the site of stress concentration might have the heterogeneous microstructural distribution. Therefore, it is necessary to clarify the creep fracture mechanism for these materials in order to predict the life of creep fracture with high degree of accuracy. In this study, the creep crack growth tests were performed using in-situ observational testing machine with microscope to observe the creep damage formation and creep crack growth behavior. The materials used are polycrystalline Ni-base superalloy IN100 and directionally solidified Ni-base superalloy CM247LC which were developed for jet engine turbine blades and gas turbine blades in electric power plants, respectively. The microstructural observation of the test specimens was also conducted using FE-SEM/EBSD. Additionally, the analyses of two-dimensional elastic-plastic creep finite element using designed methods were conducted to understand the effect of microstructural distribution on creep damage formation. The experimental and analytical results showed that it is important to determine the creep crack initiation and early crack growth to predict the life of creep fracture and it is indicated that the highly accurate prediction of creep fracture life could be realized by measuring notch opening displacement proposed as the RNOD characteristic.

Acceleration of Intended Pozzolanic Reaction under Initial Thermal Treatment for Developing Cementless Fly Ash Based Mortar.

PubMed

Kwon, Yang-Hee; Kang, Sung-Hoon; Hong, Sung-Gul; Moon, Juhyuk

2017-02-24

Without using strong alkaline solution or ordinary Portland cement, a new structural binder consisting of fly ash and hydrated lime was hardened through an intensified pozzolanic reaction. The main experimental variables are the addition of silica fume and initial thermal treatment (60 °C for 3 days). A series of experiments consisting of mechanical testing (compressive and flexural strength, modulus of elasticity), X-ray diffraction, and measurements of the heat of hydration, pore structure, and shrinkage were conducted. These tests show that this new fly ash-based mortar has a compressive strength of 15 MPa at 91 days without any silica fume addition or initial thermal treatment. The strength increased to over 50 MPa based on the acceleration of the intensified pozzolanic reaction from the silica fume addition and initial thermal treatment. This is explained by a significant synergistic effect induced by the silica fume. It intensifies the pozzolanic reaction under thermal treatment and provides a space filling effect. This improved material performance can open a new pathway to utilize the industrial by-product of fly ash in cementless construction materials.

My Quest, an Intervention Using Text Messaging to Improve Dietary and Physical Activity Behaviors and Promote Weight Loss in Low-Income Women.

PubMed

Griffin, Jamie B; Struempler, Barb; Funderburk, Katie; Parmer, Sondra M; Tran, Cecilia; Wadsworth, Danielle D

2018-01-01

To evaluate changes in dietary and physical activity behaviors and weight after implementation of a 12-week text messaging initiative (My Quest). The researchers conducted a 1-group, pre- to posttest study design to determine changes after implementation of a text messaging initiative developed using the tenets of the Social Cognitive Theory. A total of 55 Alabama counties (84% rural) with high rates of poverty, overweight/obesity, and chronic diseases. Convenience sample of low-income, primarily overweight/obese women (n = 104). Short texts (n = 2-3/d) provided health tips, reminders, and goal-setting prompts. Weekly electronic newsletters provided tips and recipes. Participant self-monitored body weight weekly. Outcomes included goal setting, self-efficacy, behavioral and environmental factors, self-monitoring, and body weight; data collection occurred through text message response and online surveys. Analyses were conducted using McNemar test (dichotomous data), Wilcoxon signed rank test (ordinal data), or paired t test (continuous data). Participants significantly (P < .05) improved dietary and physical activity behaviors and food environment; increased dietary and physical activity goal setting; and reduced body weight. A low-cost, text messaging initiative particularly targeting women residing in rural communities with high rates of poverty and obesity can promote weight loss and improve dietary and physical activity behaviors. Future studies may include a control group and social support component such as group text messaging. Copyright © 2017 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

Beam shaping for laser initiated optical primers

NASA Astrophysics Data System (ADS)

Lizotte, Todd E.

2008-08-01

Remington was one of the first firearm manufacturing companies to file a patent for laser initiated firearms, in 1969. Nearly 40 years later, the development of laser initiated firearms has not become a mainstream technology in the civilian market. Requiring a battery is definitely a short coming, so it is easy to see how such a concept would be problematic. Having a firearm operate reliably and the delivery of laser energy in an efficient manner to ignite the shock-sensitive explosive primer mixtures is a tall task indeed. There has been considerable research on optical element based methods of transferring or compressing laser energy to ignite primer charges, including windows, laser chip primers and various lens shaped windows to focus the laser energy. The focusing of laser light needs to achieve igniting temperatures upwards of >400°C. Many of the patent filings covering this type of technology discuss simple approaches where a single point of light might be sufficient to perform this task. Alternatively a multi-point method might provide better performance, especially for mission critical applications, such as precision military firearms. This paper covers initial design and performance test of the laser beam shaping optics to create simultaneous multiple point ignition locations and a circumferential intense ring for igniting primer charge compounds. A simple initial test of the ring beam shaping technique was evaluated on a standard large caliber primer to determine its effectiveness on igniting the primer material. Several tests were conducted to gauge the feasibility of laser beam shaping, including optic fabrication and mounting on a cartridge, optic durability and functional ignition performance. Initial data will be presented, including testing of optically elements and empirical primer ignition / burn analysis.

Impact-initiated damage thresholds in composites

NASA Technical Reports Server (NTRS)

Sharma, A. V.

1980-01-01

An experimental investigation was conducted to study the effect of low velocity projectile impact on the sandwich-type structural components. The materials used in the fabrication of the impact surface were graphite-, Kevlar-, and boron-fibers with appropriate epoxy matrices. The testing of the specimens was performed at moderately low- and high-temperatures as well as at room temperature to assess the impact-initiated strength degradation of the laminates. Eleven laminates with different stacking sequences, orientations, and thicknesses were tested. The low energy projectile impact is considered to simulate the damage caused by runway debris, dropping of the hand tools during servicing, etc., on the secondary aircraft structures fabricated with the composite materials. The results show the preload and the impact energy combinations necessary to cause catastrophic failures in the laminates tested. A set of faired curves indicating the failure thresholds is shown separately for the tension- and compression-loaded laminates. The specific-strengths and -moduli for the various laminates tested are also given.

NASA systems autonomy demonstration project: Advanced automation demonstration of Space Station Freedom thermal control system

NASA Technical Reports Server (NTRS)

Dominick, Jeffrey; Bull, John; Healey, Kathleen J.

1990-01-01

The NASA Systems Autonomy Demonstration Project (SADP) was initiated in response to Congressional interest in Space station automation technology demonstration. The SADP is a joint cooperative effort between Ames Research Center (ARC) and Johnson Space Center (JSC) to demonstrate advanced automation technology feasibility using the Space Station Freedom Thermal Control System (TCS) test bed. A model-based expert system and its operator interface were developed by knowledge engineers, AI researchers, and human factors researchers at ARC working with the domain experts and system integration engineers at JSC. Its target application is a prototype heat acquisition and transport subsystem of a space station TCS. The demonstration is scheduled to be conducted at JSC in August, 1989. The demonstration will consist of a detailed test of the ability of the Thermal Expert System to conduct real time normal operations (start-up, set point changes, shut-down) and to conduct fault detection, isolation, and recovery (FDIR) on the test article. The FDIR will be conducted by injecting ten component level failures that will manifest themselves as seven different system level faults. Here, the SADP goals, are described as well as the Thermal Control Expert System that has been developed for demonstration.

OECD 2-D Core Concrete Interaction (CCI) tests : CCI-2 test plan, Rev. 0 January 31, 2004.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, M. T.; Kilsdonk, D. J.; Lomperski, S.

The Melt Attack and Coolability Experiments (MACE) program addressed the issue of the ability of water to cool and thermally stabilize a molten core-concrete interaction when the reactants are flooded from above. These tests provided data regarding the nature of corium interactions with concrete, the heat transfer rates from the melt to the overlying water pool, and the role of noncondensable gases in the mixing processes that contribute to melt quenching. As a follow-on program to MACE, The Melt Coolability and Concrete Interaction Experiments (MCCI) project is conducting reactor material experiments and associated analysis to achieve the following objectives: (1)more » resolve the ex-vessel debris coolability issue through a program that focuses on providing both confirmatory evidence and test data for the coolability mechanisms identified in MACE integral effects tests, and (2) address remaining uncertainties related to long-term two-dimensional molten core-concrete interactions under both wet and dry cavity conditions. Achievement of these two program objectives will demonstrate the efficacy of severe accident management guidelines for existing plants, and provide the technical basis for better containment designs for future plants. In terms of satisfying these objectives, the Management Board (MB) approved the conduct of two long-term 2-D Core-Concrete Interaction (CCI) experiments designed to provide information in several areas, including: (i) lateral vs. axial power split during dry core-concrete interaction, (ii) integral debris coolability data following late phase flooding, and (iii) data regarding the nature and extent of the cooling transient following breach of the crust formed at the melt-water interface. The first of these two tests, CCI-1, was conducted on December 19, 2003. This test investigated the interaction of a fully oxidized 400 kg PWR core melt, initially containing 8 wt % calcined siliceous concrete, with a specially designed two-dimensional siliceous concrete test section with an initial cross-sectional area of 50 cm x 50 cm. The second of these two planned tests, CCI-2, will be conducted with a nearly identical test facility and experiment boundary conditions, but with a Limestone/Common Sand (LCS) concrete test section to investigate the effect of concrete type on the two-dimensional core-concrete interaction and debris cooling behavior. The objective of this report is to provide the overall test plan for CCI-2 to enable pretest calculations to be carried out. The report begins by providing a summary description of the CCI-2 test apparatus, followed by a description of the planned test operating procedure. Overall specifications for CCI-2 are provided in Table 1-1.« less

Three-Dimensional Structure of Thermohaline Staircases in the Tropical North Atlantic and Their Effect on Acoustic Propagation

DTIC Science & Technology

2012-12-01

PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Naval Postgraduate School Monterey, CA 93943–5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9...experiment initially designed to test pressure at the base of an ocean, by inserting a narrow heat-conducting pipe vertically to draw water to the...tgα ≈ tgαT (6) Wall thus hypothesized that the interface should align with isotherms but not necessarily isohalines. An observational test was

A critical review of the life sciences project management at Ames Research Center for the Spacelab Mission development test 3

NASA Technical Reports Server (NTRS)

Helmreich, R. L.; Wilhelm, J. M.; Tanner, T. A.; Sieber, J. E.; Burgenbauch, S. F.

1979-01-01

A management study was initiated by ARC (Ames Research Center) to specify Spacelab Mission Development Test 3 activities and problems. This report documents the problems encountered and provides conclusions and recommendations to project management for current and future ARC life sciences projects. An executive summary of the conclusions and recommendations is provided. The report also addresses broader issues relevant to the conduct of future scientific missions under the constraints imposed by the space environment.

Expansion tunnel performance with and without an electromagnetically opened tertiary diaphragm

NASA Technical Reports Server (NTRS)

Miller, C. G.

1977-01-01

A study was conducted to examine the effect of synchronization of an electromagnetically opened tertiary diaphragm with flow arrival at the diaphragm on the pitot pressure measured at the test section of an expansion tunnel. The effect of tertiary diaphragm pressure ratio (ratio of initial nozzle pressure to quiescent acceleration section pressure) on the pitot pressure time history is also determined. The inadequacy of a pressure transducer protection arrangement used in previous expansion tube and expansion tunnel tests was revealed.

Reaerosolization of Fluidized Spores in Ventilation Systems▿

PubMed Central

Krauter, Paula; Biermann, Arthur

2007-01-01

This project examined dry, fluidized spore reaerosolization in a heating, ventilating, and air conditioning duct system. Experiments using spores of Bacillus atrophaeus, a nonpathogenic surrogate for Bacillus anthracis, were conducted to delineate the extent of spore reaerosolization behavior under normal indoor airflow conditions. Short-term (five air-volume exchanges), long-term (up to 21,000 air-volume exchanges), and cycled (on-off) reaerosolization tests were conducted using two common duct materials. Spores were released into the test apparatus in turbulent airflow (Reynolds number, 26,000). After the initial pulse of spores (approximately 1010 to 1011 viable spores) was released, high-efficiency particulate air filters were added to the air intake. Airflow was again used to perturb the spores that had previously deposited onto the duct. Resuspension rates on both steel and plastic duct materials were between 10−3 and 10−5 per second, which decreased to 10 times less than initial rates within 30 min. Pulsed flow caused an initial spike in spore resuspension concentration that rapidly decreased. The resuspension rates were greater than those predicted by resuspension models for contamination in the environment, a result attributed to surface roughness differences. There was no difference between spore reaerosolization from metal and that from plastic duct surfaces over 5 hours of constant airflow. The spores that deposited onto the duct remained a persistent source of contamination over a period of several hours. PMID:17293522

Low thrust rocket test facility

NASA Technical Reports Server (NTRS)

Arrington, Lynn A.; Schneider, Steven J.

1990-01-01

A low thrust chemical rocket test facility has recently become operational at the NASA-Lewis. The new facility is used to conduct both long duration and performance tests at altitude over a thruster's operating envelope using hydrogen and oxygen gas for propellants. The facility provides experimental support for a broad range of objectives, including fundamental modeling of fluids and combustion phenomena, the evaluation of thruster components, and life testing of full rocket designs. The major mechanical and electrical systems are described along with aspects of the various optical diagnostics available in the test cell. The electrical and mechanical systems are designed for low down time between tests and low staffing requirements for test operations. Initial results are also presented which illustrate the various capabilities of the cell.

Environmental complex mixture toxicity assessment.

PubMed

Gardner, H S; Brennan, L M; Toussaint, M W; Rosencrance, A B; Boncavage-Hennessey, E M; Wolfe, M J

1998-12-01

Trichloroethylene (TCE) was found as a contaminant in the well supplying water to an aquatic testing laboratory. The groundwater was routinely screened by a commercial laboratory for volatile and semivolatile compounds, metals, herbicides, pesticides, and polychlorinated biphenyls using U.S. Environmental Protection Agency methods. Although TCE was the only reportable peak on the gas chromatograph, with average concentrations of 0.200 mg/l, other small peaks were also present, indicating the possibility that the contamination was not limited to TCE alone. A chronic 6-month carcinogenicity assay was conducted on-site in a biomonitoring trailer, using the Japanese medaka fish (Oryzias latipes) in an initiation-promotion protocol, with diethylnitrosamine (DEN) as the initiator and the TCE-contaminated groundwater as a promoter. Study results indicated no evidence of carcinogenic potential of the groundwater without initiation. There was, however, a tumor-promotional effect of the groundwater after DEN initiation. A follow-up laboratory study was conducted using reagent grade TCE added to carbon-filtered groundwater to simulate TCE concentrations comparable to those found in the contaminated groundwater. Study results indicated no promotional effects of TCE. These studies emphasize the necessity for on-site bioassays to assess potential environmental hazards. In this instance, chemical analysis of the groundwater identified TCE as the only reportable contaminant, but other compounds present below reportable limits were noted and may have had a synergistic effect on tumor promotion observed with the groundwater exposure. Laboratory toxicity testing of single compounds can produce toxicity data specific to that compound for that species but cannot take into account the possible toxic effects of mixtures of compounds.

Regional Environmental Monitoring and Assessment Program Data (REMAP)

EPA Pesticide Factsheets

The Regional Environmental Monitoring and Assessment Program (REMAP) was initiated to test the applicability of the Environmental Monitoring and Assessment Program (EMAP) approach to answer questions about ecological conditions at regional and local scales. Using EMAP's statistical design and indicator concepts, REMAP conducts projects at smaller geographic scales and in shorter time frames than the national EMAP program.

A CIS (Clinical Information System) Quality Evaluation Tool for Nursing Care Services

ERIC Educational Resources Information Center

Lee, Seon Ah

2010-01-01

The purpose of this study was to develop a tool to evaluate the quality of a clinical information system (CIS) conceived by nurses and conduct a pilot test with the developed tool as an initial assessment. CIS quality is required for successful implementation in information technology (IT) environments. The study started with the realization that…

A Multilevel Analysis of the Relationship between Shared Leadership and Creativity in Inter-Organizational Teams

ERIC Educational Resources Information Center

Gu, Jibao; Chen, Zhi; Huang, Qian; Liu, Hefu; Huang, Shenglan

2018-01-01

An inter-organizational team, which consists of diverse members from different organizations to conduct an initiative, has been widely treated as a critical method to improve organizational innovation. This study proposes a multilevel model to test the relationship between shared leadership and creativity at both team- and individual level in the…

The Pollyanna Principle in Business Writing: Initial Results, Suggestions for Research.

ERIC Educational Resources Information Center

Hildebrandt, Herbert W.

A study was conducted to determine whether there was a linguistic correlation between a financially good year and a bad year as expressed in the annual reports of company presidents to their shareholders. Specifically the study tested the "Pollyanna Principle," which states (1) that regardless of whether the year was financially good or bad, the…

40 CFR 60.2690 - How do I conduct the initial and annual performance test?

Code of Federal Regulations, 2010 CFR

2010-07-01

... part must be used for gas composition analysis, including measurement of oxygen concentration. Method... concentrations, except for opacity, must be adjusted to 7 percent oxygen using Equation 1 of this section: Cadj = Cmeas (20.9−7)/(20.9−%O2)(Eq. 1) Where: Cadj = pollutant concentration adjusted to 7 percent oxygen...

Evaluation of the Japanese Laricobius sp. n. and other natural enemies of hemlock woolly adelgid in Japan

Treesearch

Ashley Lamb; Shigehiko Shiyake; Scott Salom; Michael Montgomery; Loke Kok

2008-01-01

Since the initial importation of the Japanese Laricobius (Coleoptera: Derodontidae) to Virginia in 2006, we have studied the development of the predator at two different temperatures, measured feeding and oviposition rates, conducted preliminary host-range testing, and reared two generations. During this time, we have learned this predator differs...

40 CFR 63.2358 - By what date must I conduct performance tests and other initial compliance demonstrations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... racks at existing affected sources complying with the emission limitations listed in Table 2 to this... storage tanks and transfer racks at reconstructed or new affected sources complying with the emission... section, you must comply within 180 days after April 25, 2011. (2) For transfer racks and equipment leak...

An instrument for spatial conductivity measurements of high Tc superconducting (HTSC) materials

NASA Technical Reports Server (NTRS)

Vansant, T.

1991-01-01

High T(sub c) Superconducting (HTSC) thin films are suggested for use in a number of aerospace applications such as an IR bolometer and as electromagnetic shielding. As part of its flight assurance role, the Materials Branch of the Goddard Space Flight Center has initiated development of an instrument capable of measuring variations in conductivity for flat samples using an eddy current testing device and an X-Y positioning table. This instrument was used to examine bulk HTSC samples. System changes that would enable characterization of thin film materials are discussed.

An augmented SMS intervention to improve access to antenatal CD4 testing and ART initiation in HIV-infected pregnant women: a cluster randomized trial.

PubMed

Dryden-Peterson, Scott; Bennett, Kara; Hughes, Michael D; Veres, Adrian; John, Oaitse; Pradhananga, Rosina; Boyer, Matthew; Brown, Carolyn; Sakyi, Bright; van Widenfelt, Erik; Keapoletswe, Koona; Mine, Madisa; Moyo, Sikhulile; Asmelash, Aida; Siedner, Mark; Mmalane, Mompati; Shapiro, Roger L; Lockman, Shahin

2015-01-01

Less than one-third of HIV-infected pregnant women eligible for combination antiretroviral therapy (ART) globally initiate treatment prior to delivery, with lack of access to timely CD4 results being a principal barrier. We evaluated the effectiveness of an SMS-based intervention to improve access to timely antenatal ART. We conducted a stepped-wedge cluster randomized trial of a low-cost programmatic intervention in 20 antenatal clinics in Gaborone, Botswana. From July 2011-April 2012, 2 clinics were randomly selected every 4 weeks to receive an ongoing clinic-based educational intervention to improve CD4 collection and to receive CD4 results via an automated SMS platform with active patient tracing. CD4 testing before 26 weeks gestation and ART initiation before 30 weeks gestation were assessed. Three-hundred-sixty-six ART-naïve women were included, 189 registering for antenatal care under Intervention and 177 under Usual Care periods. Of CD4-eligible women, 100 (59.2%) women under Intervention and 79 (50.6%) women under Usual Care completed CD4 phlebotomy before 26 weeks gestation, adjusted odds ratio (aOR, adjusted for time that a clinic initiated Intervention) 0.87 (95% confidence interval [CI]0.47-1.63, P = 0.67). The SMS-based platform reduced time to clinic receipt of CD4 test result from median of 16 to 6 days (P<0.001), was appreciated by clinic staff, and was associated with reduced operational cost. However, rates of ART initiation remained low, with 56 (36.4%) women registering under Intervention versus 37 (24.2%) women under Usual Care initiating ART prior to 30 weeks gestation, aOR 1.06 (95%CI 0.53-2.13, P = 0.87). The augmented SMS-based intervention delivered CD4 results more rapidly and efficiently, and this type of SMS-based results delivery platform may be useful for a variety of tests and settings. However, the intervention did not appear to improve access to timely antenatal CD4 testing or ART initiation, as obstacles other than CD4 impeded ART initiation during pregnancy.

Fatigue Life Estimation under Cumulative Cyclic Loading Conditions

NASA Technical Reports Server (NTRS)

Kalluri, Sreeramesh; McGaw, Michael A; Halford, Gary R.

1999-01-01

The cumulative fatigue behavior of a cobalt-base superalloy, Haynes 188 was investigated at 760 C in air. Initially strain-controlled tests were conducted on solid cylindrical gauge section specimens of Haynes 188 under fully-reversed, tensile and compressive mean strain-controlled fatigue tests. Fatigue data from these tests were used to establish the baseline fatigue behavior of the alloy with 1) a total strain range type fatigue life relation and 2) the Smith-Wastson-Topper (SWT) parameter. Subsequently, two load-level multi-block fatigue tests were conducted on similar specimens of Haynes 188 at the same temperature. Fatigue lives of the multi-block tests were estimated with 1) the Linear Damage Rule (LDR) and 2) the nonlinear Damage Curve Approach (DCA) both with and without the consideration of mean stresses generated during the cumulative fatigue tests. Fatigue life predictions by the nonlinear DCA were much closer to the experimentally observed lives than those obtained by the LDR. In the presence of mean stresses, the SWT parameter estimated the fatigue lives more accurately under tensile conditions than under compressive conditions.

Installation and checkout of the DOE/NASA Mod-1 2000-kW wind turbine generator

NASA Technical Reports Server (NTRS)

Puthoff, R. L.; Collins, J. L.; Wolf, R. A.

1980-01-01

The paper describes the DOE/NASA Mod-1 wind turbine generator, its assembly and testing, and its installation at Boone, North Carolina. The paper concludes with performance data taken during the initial tests conducted on the machine. The successful installation and initial operation of the Mod-1 wind turbine generator has had the following results: (1) megawatt-size wind turbines can be operated satisfactorily on utility grids; (2) the structural loads can be predicted by existing codes; (3) assembly of the machine on top of the tower presents no major problem; (4) large blades 100 ft long can be transported long distances and over mountain roads; and (5) operating experience and performance data will contribute substantially to the design of future low-cost wind turbines.

Advanced thermionic energy conversion

NASA Technical Reports Server (NTRS)

Britt, E. J.; Fitzpatrick, G. D.; Hansen, L. K.; Rasor, N. S.

1974-01-01

Basic analytical and experimental exploration was conducted on several types of advanced thermionic energy converters, and preliminary analysis was performed on systems utilizing advanced converter performance. The Pt--Nb cylindrical diode which exhibited a suppressed arc drop, as described in the preceding report, was reassembled and the existence of the postulated hydrid mode of operation was tentatively confirmed. Initial data obtained on ignited and unignited triode operation in the demountable cesium vapor system essentially confirmed the design principles developed in earlier work, with a few exceptions. Three specific advanced converter concepts were selected as candidates for concentrated basic study and for practical evaluation in fixed-configuration converters. Test vehicles and test stands for these converters and a unique controlled-atmosphere station for converter assembly and processing were designed, and procurement was initiated.

Comparison of Analytical Predictions and Experimental Results for a Dual Brayton Power System

NASA Technical Reports Server (NTRS)

Johnson, Paul

2007-01-01

NASA Glenn Research Center (GRC) contracted Barber- Nichols, Arvada, CO to construct a dual Brayton power conversion system for use as a hardware proof of concept and to validate results from a computational code known as the Closed Cycle System Simulation (CCSS). Initial checkout tests were performed at Barber- Nichols to ready the system for delivery to GRC. This presentation describes the system hardware components and lists the types of checkout tests performed along with a couple issues encountered while conducting the tests. A description of the CCSS model is also presented. The checkout tests did not focus on generating data, therefore, no test data or model analyses are presented.

Development and field testing of a smartphone "App" for tinnitus management.

PubMed

Henry, James A; Thielman, Emily; Zaugg, Tara; Kaelin, Christine; Choma, Christie; Chang, Bill; Hahn, Shira; Fuller, Bret

2017-10-01

This study's objective was to develop and test a smartphone app that supports learning and using coping skills for managing tinnitus. The app's content was based on coping skills that are taught as a part of progressive tinnitus management (PTM). The study involved three phases: (1) develop a prototype app and conduct usability testing; (2) conduct two focus groups to obtain initial feedback from individuals representing potential users; and (3) conduct a field study to evaluate the app, with three successive groups of participants. Participants were adults with bothersome tinnitus. For Phase 2, two focus groups were attended by a total of 17 participants. Phase 3 involved three consecutive rounds of participants: five from the focus groups followed by two rounds with 10 participants each who had not seen the app previously. In both the focus groups and field studies, participants responded favourably to the content. Certain features, however, were deemed too complex. Completion of this project resulted in the development and testing of the delivery of PTM coping skills via a smartphone app. This new approach has the potential to improve access to coping skills for those with bothersome tinnitus.

NASA Dryden's two T-38A mission support aircraft fly in tight formation while conducting a pitot-static airspeed calibration check near Edwards Air Force Base

NASA Image and Video Library

2007-09-26

NASA Dryden Flight Research Center's two T-38A Talon mission support aircraft flew together for the first time on Sept. 26, 2007 while conducting pitot-static airspeed calibration checks during routine pilot proficiency flights. The two aircraft, flown by NASA research pilots Kelly Latimer and Frank Batteas, joined up with a NASA Dryden F/A-18 flown by NASA research pilot Dick Ewers to fly the airspeed calibrations at several speeds and altitudes that would be flown by the Stratospheric Observatory for Infrared Astronomy (SOFIA) Boeing 747SP during its initial flight test phase. The T-38s, along with F/A-18s, serve in a safety chase role during those test missions, providing critical instrument and visual monitoring for the flight test series.

Design and evaluation of thrust vectored nozzles using a multicomponent thrust stand

NASA Technical Reports Server (NTRS)

Carpenter, Thomas W.; Blattner, Ernest W.; Stagner, Robert E.; Contreras, Juanita; Lencioni, Dennis; Mcintosh, Greg

1990-01-01

Future aircraft with the capability of short takeoff and landing, and improved maneuverability especially in the post-stall flight regime will incorporate exhaust nozzles which can be thrust vectored. In order to conduct thrust vector research in the Mechanical Engineering Department at Cal Poly, a program was planned with two objectives; design and construct a multicomponent thrust stand for the specific purpose of measuring nozzle thrust vectors; and to provide quality low moisture air to the thrust stand for cold flow nozzle tests. The design and fabrication of the six-component thrust stand was completed. Detailed evaluation tests of the thrust stand will continue upon the receipt of one signal conditioning option (-702) for the Fluke Data Acquisition System. Preliminary design of thrust nozzles with air supply plenums were completed. The air supply was analyzed with regard to head loss. Initial flow visualization tests were conducted using dual water jets.

Stable tearing behavior of a thin-sheet material with multiple cracks

NASA Technical Reports Server (NTRS)

Dawicke, D. S.; Newman, J. C., Jr.; Sutton, M. A.; Amstutz, B. E.

1994-01-01

Fracture tests were conducted on 2.3mm thick, 305mm wide sheets of 2024-T3 aluminum alloy with 1-5 collinear cracks. The cracks were introduced (crack history) into the specimens by three methods: (1) saw cutting; (2) fatigue precracking at a low stress range; and (3) fatigue precracking at a high stress range. For the single crack tests, the initial crack history influenced the stress required for the onset of stable crack growth and the first 10mm of crack growth. The effect on failure stress was about 4 percent or less. For the multiple crack tests, the initial crack history was shown to cause differences of more than 20 percent in the link-up stress and 13 percent in failure stress. An elastic-plastic finite element analysis employing the Crack Tip Opening Angle (CTOA) fracture criterion was used to predict the fracture behavior of the single and multiple crack tests. The numerical predictions were within 7 percent of the observed link-up and failure stress in all the tests.