40 CFR 98.449 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... into the atmosphere, indoor air, oceans, or surface water. Underground Injection Control permit means a... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY... below, all terms used in this subpart have the same meaning given in the Clean Air Act and subpart A of...

Application of an Area-of-Review (AOR) Concept to the East Texas Field and Other Selected Texas Oilfields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warner, Don L.; Koederitz, Leonard F.; Laudon, Robert C.

The Underground Injection Control Regulations promulgated in 1980, under the Safe Drinking Water Act of 1974, require Area-of-Review (AOR) studies be conducted as part of the permitting process for newly drilled or converted Class II injection wells. Existing Class II injection wells operating at the time regulations became effective were excluded from the AOR requirement. The AOR is the area surrounding an injection well or wells defined by either the radial distance within which pressure in the injection zone may cause migration of the injection and/or formation fluid into an underground source of drinking water (USDW) or defined by amore » fixed radius of not less than one-fourth mile. In the method where injection pressure is used to define the AOR radial distance, the AOR is also known as the ''zone of endangering influence.''« less

Ultrasound-guided microinjection into the mouse forebrain in utero at E9.5.

PubMed

Pierfelice, Tarran J; Gaiano, Nicholas

2010-11-13

In utero survival surgery in mice permits the molecular manipulation of gene expression during development. However, because the uterine wall is opaque during early embryogenesis, the ability to target specific parts of the embryo for microinjection is greatly limited. Fortunately, high-frequency ultrasound imaging permits the generation of images that can be used in real time to guide a microinjection needle into the embryonic region of interest. Here we describe the use of such imaging to guide the injection of retroviral vectors into the ventricular system of the mouse forebrain at embryonic day (E) 9.5. This method uses a laparotomy to permit access to the uterine horns, and a specially designed plate that permits host embryos to be bathed in saline while they are imaged and injected. Successful surgeries often result in most or all of the injected embryos surviving to any subsequent time point of interest (embryonically or postnatally). The principles described here can be used with slight modifications to perform injections into the amnionic fluid of E8.5 embryos (thereby permitting infection along the anterior posterior extent of the neural tube, which has not yet closed), or into the ventricular system of the brain at E10.5/11.5. Furthermore, at mid-neurogenic ages (~E13.5), ultrasound imaging can be used direct injection into specific brain regions for viral infection or cell transplantation. The use of ultrasound imaging to guide in utero injections in mice is a very powerful technique that permits the molecular and cellular manipulation of mouse embryos in ways that would otherwise be exceptionally difficult if not impossible.

78 FR 14951 - State of Washington; Underground Injection Control (UIC) Program Revision

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-08

... of Ecology to the Energy Facility Site Evaluation Council to issue UIC permits at energy facilities... telephone number for the Library is (206) 553-1289. (2) Washington Department of Ecology, Water Quality... the Environmental Protection Agency, and MOUs between the Department of Ecology and the Department of...

40 CFR 144.4 - Considerations under Federal law.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Considerations under Federal law. 144... (CONTINUED) UNDERGROUND INJECTION CONTROL PROGRAM General Provisions § 144.4 Considerations under Federal law. The following is a list of Federal laws that may apply to the issuance of permits under these rules...

78 FR 48639 - North Dakota Underground Injection Control Program Revision Application

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-09

... Dakota Industrial Commission, Oil and Gas Division 1016 East Calgary Avenue, Bismarck, North Dakota 58503... the North Dakota Industrial Commission (NDIC) to issue UIC permits for carbon geo-sequestration... protected through www.regulations.gov or email. The www.regulations.gov Web site is an ``anonymous access...

Highly controlled vascular syringes for pericardiocentesis.

PubMed

Ricciardi, Mark; Roldan, Carlos; Sibbitt, Randy; Sibbitt, Wilmer; Michael, Adrian; Palmer, Dennis

2010-12-01

The present study determined the utility and needle control characteristics of highly controlled vascular syringes for image-guided pericardiocentesis. Vascular syringes have been integrated into invasive cardiovascular procedures with improved patient safety, but to date have not been used in pericardiocentesis. To address this issue, we determined the method of use of vascular syringes for pericardiocentesis. A vascular syringe with reciprocating plungers, the reciprocating procedure device (RPD syringe), replaced the corresponding 10 ml and 20 ml conventional syringes in a standard pericardiocentesis tray. The vascular syringe is controlled with one hand, and can either aspirate or inject by pushing the corresponding aspiration or injection plunger. Four hundred and thirty seven subjects underwent vascular syringe procedures. The linear displacement method was used to precisely measure control of the needle tip in millimeters (mm) in vascular syringes compared to conventional syringes in 20 individual operators. Relative to the corresponding 10 ml and 20 ml conventional syringes, vascular syringes significantly reduced unintended forward penetration of the needle tip by 44% (7.0 ± 4.3 mm; p < 0.0001) and 53% (10.1 ± 5.5 mm; p < 0.0001), respectively, and reduced unintended retraction of the needle by 56% (2.7 ± 2.2 mm; p < 0.001) and 60% (3.5 ± 2.5 mm; p < 0.001), respectively. During pericardiocentesis, the mechanical syringe permitted facile one-handed aspiration and maintained the operator's ability to clear the needle. In the 437 vascular syringe procedures, there were no complications, with an estimated cost savings of $10-65 per procedure. Vascular syringes improve needle control in pericardiocentesis, promote patient safety and permit one-handed aspiration and injection.

Evaluation of neonicotinoid, organophosphate and avermectin trunk injections for the management of avocado thrips in California avocado groves.

PubMed

Byrne, Frank J; Urena, Anthony A; Robinson, Lindsay J; Krieger, Robert I; Doccola, Joe; Morse, Joseph G

2012-05-01

Trunk injections of systemic insecticides were evaluated for the management of avocado thrips. Insecticide residues were quantified in leaves to determine when after treatment, and for how long, toxic concentrations of the insecticides were present. Residues in fruit were quantified to determine whether trunk injection of insecticides might present a greater risk than traditional application methods for contaminating fruit. Residues of imidacloprid and dinotefuran were at least tenfold higher in leaves when trees were treated via trunk injection compared with soil application. Dinotefuran uptake was more rapid than imidacloprid, and no residues were detected within fruit. Acephate was also mobilized very rapidly and gave good control of thrips in bioassays; however, residues of acephate and its insecticidal metabolite methamidophos were detected in the fruit for up to 4 weeks after injection. Avermectin uptake was very slow, and it was ineffective against avocado thrips. Trunk injections of acephate and dinotefuran permitted rapid uptake into avocados, and they are strong candidates as control methods for avocado thrips. However, residues of organophosphates in fruit could necessitate increased preharvest intervals. Residues of neonicotinoids were below detection limits in fruit, suggesting that neonicotinoids may be the more suitable control option of the two chemical classes. Copyright © 2012 Society of Chemical Industry.

Requirements for a transformerless power conditioning system

NASA Technical Reports Server (NTRS)

Klein, J.; Koerner, T.; Rippel, W.; Kalbach, J.

1984-01-01

Requirements for development of a Transformerless Power Conditioning Subsystem (TPCS) that will meet utility, manufacturer, and customer needs are detailed. Issues analyzed include current utility guidelines, safety and grounding issues that appear as local codes, various kinds of TPCS connections that can be developed, dc injection, and a brief survey of TPCS circuit topologies that will meet requirements. The major result is that a finite time exists for control operation before dc injection into the distribution transformer causes customer outage (on the order of seconds). This time permits the control system to sense a dc injection condition and remove the TPCS from the utility system. Requirements for such a control system are specified. A three wire connection will ensure balanced operation for customer loads and two wire connections caused average value dc to be injected into single phase loads. This type of connection also allows for the lowest array voltage. The conclusion is that requirements for a TPCS can be determined and that there are not showstopping issues preventing implementation. The actual design and topology of the TPCS was left for further study.

77 FR 27451 - Permitting Guidance for Oil and Gas Hydraulic Fracturing Activities Using Diesel Fuels-Draft...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-10

... authority. The draft guidance includes EPA's interpretation of the Safe Drinking Water Act (SDWA) and...., Washington, DC 20460. Hand Delivery: Office of Water (OW) Docket, EPA/DC, EPA West, Room 3334, 1301... Injection Control Program, Drinking Water Protection Division, Office of Ground Water and Drinking Water (MC...

77 FR 40354 - Permitting Guidance for Oil and Gas Hydraulic Fracturing Activities Using Diesel Fuels-Draft

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-09

... INFORMATION CONTACT: Sherri Comerford, Underground Injection Control (UIC) Program, Drinking Water Protection Division, Office of Ground Water and Drinking Water (MC-4606M), Environmental Protection Agency, 1200... Fracturing and the Safe Drinking Water Act Web site, http://water.epa.gov/type/groundwater/uic/class2...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chandler, D.P.; Welt, M.; Leung, F.C.

An efficient one-step injection technique for gene insertion into fertilized rainbow trout (Oncorhynchus mykiss) eggs is described, and basic parameters affecting egg survival are reported. Freshly fertilized rainbow trout eggs were injected in the perivitelline space with a recombinant mouse metallothionein-genomic bovine growth hormone (bGH) DNA construct using a 30-gauge hypodermic needle and a standard microinjection system. Relative to control, site of injection and DNA concentration did not affect the egg survival, but injections later than 3--4 hours post fertilization were detrimental. The injection technique permitted treatment of 100 eggs/hr with survivals up to 100%, resulting in a 4% DNAmore » uptake rate as indicated by DNA dot blot analysis. Positive dot blot results also indicated that the injected DNA is able to cross the vitelline membrane and persist for 50--60 days post hatching, obviating the need for direct injection into the germinal disk. Results are consistent with previous transgenic fish work, underscoring the usefulness of the technique for generating transgenic trout and salmonids. 24 refs., 6 figs., 3 tabs.« less

Data requirements for simulation of hydrogeologic effects of liquid waste injection, Harrison and Jackson Counties, Mississippi

USGS Publications Warehouse

Rebich, Richard A.

1994-01-01

Available literature and data were reviewed to quantify data requirements for computer simulation of hydrogeologic effects of liquid waste injection in southeastern Mississippi. Emphasis of each review was placed on quantifying physical properties of current Class I injection zones in Harrison and Jackson Counties. Class I injection zones are zones that are used for injection of hazardous or non-hazardous liquid waste below a formation containing the lowermost underground source of drinking water located within one-quarter of a mile of the injection well. Several mathematical models have been developed to simulate injection effects. The Basic Plume Method was selected because it is commonly used in permit applications, and the Intercomp model was selected because it is generally accepted and used in injection-related research. The input data requirements of the two models were combined into a single data requirement list inclusive of physical properties of injection zones only; injected waste and well properties are not included because such information is site-specific by industry, which is beyond the scope of this report. Results of the reviews of available literature and data indicated that Class I permit applications and standard-reference chemistry and physics texts were the primary sources of information to quantify physical properties of injection zones in Harrison and Jackson Counties. With the exception of a few reports and supplementary data for one injection zone in Jackson County, very little additional information pertaining to physical properties of the injection zones was available in sources other than permit applications and standard-reference texts.

40 CFR 147.2906 - Emergency permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... substantial delay in oil or gas production, and injection will not result in movement of fluid into an USDW... permits to avoid a substantial delay in oil or gas production shall be issued only after a complete permit... notice procedure for a draft permit within 10 days after issuance. (3) An emergency permit may be oral or...

Pre-emptive ice cube cryotherapy for reducing pain from local anaesthetic injections for simple lacerations: a randomised controlled trial.

PubMed

Song, JaeWoo; Kim, HyukHoon; Park, EunJung; Ahn, Jung Hwan; Yoon, Eunhui; Lampotang, Samsun; Gravenstein, Nikolaus; Choi, SangChun

2018-02-01

Subcutaneous local anaesthetic injection can be painful to patients in the ED. We evaluated the effect of cryotherapy by application of an ice cube to the injection site prior to injection in patients with simple lacerations. We conducted a prospective, randomised, controlled trial in consented patients with simple lacerations needing primary repair at a single emergency centre from April to July 2016. We randomly assigned patients undergoing repair for simple lacerations to either the cryotherapy group or the control group (standard care; no cryotherapy or other pretreatment of the injection site). In cryotherapy group subjects, we applied an ice cube (size: 1.5×1.5×1.5 cm) placed inside a sterile glove on the wound at the anticipated subcutaneous lidocaine injection site for 2 min prior to injection. The primary outcome was a subjective numeric rating (0-10 scale) of the perceived pain from the subcutaneous local anaesthetic injections. Secondary outcomes were (a) perceived pain on a numeric scale for cryotherapy itself, that is, pain from contact of the ice cube/glove with the skin and (b) the rate of complications after primary laceration repair. Fifty patients were enrolled, consented and randomised, with 25 in the cryotherapy group and 25 in the control group. The numeric rating scale for subcutaneous anaesthetic injections was median, IQR, 95% CI 2.0 (1 to 3.5), 1.81 to 3.47, respectively, in the cryotherapy group and 5.0 (3 to 7), 3.91 to 6.05 in the control group (Mann-Whitney U=147.50, p=0.001). No wound complications occurred in either group. The numeric rating scale for cryotherapy itself was median, IQR, 95% CI: 2.0 (1 to 3.5), 1.90 to 3.70. Pre-emptive topical injection site cryotherapy lasting 2 min before subcutaneous local anaesthetic injections can significantly reduce perceived pain from subcutaneous local anaesthetic injections in patients presenting for simple laceration repair. KCT0001990. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Bimodal exciton-plasmon light sources controlled by local charge carrier injection.

PubMed

Merino, Pablo; Rosławska, Anna; Große, Christoph; Leon, Christopher C; Kuhnke, Klaus; Kern, Klaus

2018-05-01

Electrical charges can generate photon emission in nanoscale quantum systems by two independent mechanisms. First, radiative recombination of pairs of oppositely charged carriers generates sharp excitonic lines. Second, coupling between currents and collective charge oscillations results in broad plasmonic bands. Both luminescence modes can be simultaneously generated upon charge carrier injection into thin C 60 crystallites placed in the plasmonic nanocavity of a scanning tunneling microscope (STM). Using the sharp tip of the STM as a subnanometer-precise local electrode, we show that the two types of electroluminescence are induced by two separate charge transport channels. Holes injected into the valence band promote exciton generation, whereas electrons extracted from the conduction band cause plasmonic luminescence. The different dynamics of the two mechanisms permit controlling their relative contribution in the combined bimodal emission. Exciton recombination prevails for low charge injection rates, whereas plasmon decay outshines for high tunneling currents. The continuous transition between both regimes is described by a rate model characterizing emission dynamics on the nanoscale. Our work provides the basis for developing blended exciton-plasmon light sources with advanced functionalities.

The Efficacy of Cyclic Injection of Bone Morphogenetic Protein-2 in Large-Scale Calvarial Bone Defects.

PubMed

Choi, Jin Mi; Jeong, Woo Shik; Park, Eun Jung; Choi, Jong Woo

2017-03-01

Bone morphogenetic protein-2 (BMP-2) appears to be one of the most potent growth factors thus far studied. However, recent publications on the clinical application of BMP-2 revealed that its correct control is the paramount issue in clinical practice. For improving BMP-2 delivery, the cyclic administration might be an alternative. Accordingly, the authors cyclically injected BMP-2 in a cyclic injection model of large cranial defects to maintain the proper dosage during the bone healing process. A 10-mm diameter calvarial bone defect was produced using a round drill in 8-week-old Sprague-Dawley rats. Silk-hydroxyapatite scaffolds soaked in the appropriate concentration of BMP-2 were implanted into the defect. The animals were split into 4 single-injection groups and 3 multiple-injection groups; the latter groups received weekly subcutaneous injections of BMP-2 solution (1, 5, and 10 μg/mL) for 4 weeks, whereas the former groups received a single injection of BMP-2 at these concentrations. Each rat underwent computed tomography at 8 weeks. In terms of total volumes of the new bone, the 5 μg/mL multiple-injection BMP-2 group had significantly greater increases in bone volume than the single-injection groups. In terms of bone thickness, the multiple-injection groups had better outcomes than the single-injection groups. Thus, the cyclic injection protocol restored the original thickness without overgrowth. Cyclic injection of BMP-2 permits more accurate dosage control than single injection and improves thickness and dense bone regeneration. Therefore, it may represent a promising approach for future clinical trials. Further investigation using a greater number of animals is required.

CXA La Paloma, LLC: UIC Class I Permit No.CA10710001

EPA Pesticide Factsheets

Documents related to La Paloma Generating Company, LLC's (LPGC) application for a UIC permit renewal (of permit #CA199000001) to operate a Class I injection well facility to dispose of non-hazardous wastewater from the La Paloma Generating Plant.

Optimal joule heating of the subsurface

DOEpatents

Berryman, James G.; Daily, William D.

1994-01-01

A method for simultaneously heating the subsurface and imaging the effects of the heating. This method combines the use of tomographic imaging (electrical resistance tomography or ERT) to image electrical resistivity distribution underground, with joule heating by electrical currents injected in the ground. A potential distribution is established on a series of buried electrodes resulting in energy deposition underground which is a function of the resistivity and injection current density. Measurement of the voltages and currents also permits a tomographic reconstruction of the resistivity distribution. Using this tomographic information, the current injection pattern on the driving electrodes can be adjusted to change the current density distribution and thus optimize the heating. As the heating changes conditions, the applied current pattern can be repeatedly adjusted (based on updated resistivity tomographs) to affect real time control of the heating.

An Apparatus for Pressure Injection of Solutions into Trees

Treesearch

Thomas W. Jones; Garold F. Gregory; Garold F. Gregory

1971-01-01

The construction and use of an apparatus for injecting solutions under pressure into trees is described. A unique and important feature of the apparatus is that it permits injection of solutions into the outermost sapwood. It has been used to inject dye solutions and solubilized benomyl into elm, oak, and maple.

Development of Science-Based Permitting Guidance for Geological Sequestration of CO2 in Deep Saline Aquifers Based on Modeling and Risk Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jean-Philippe Nicot; Renaud Bouroullec; Hugo Castellanos

2006-06-30

Underground carbon storage may become one of the solutions to address global warming. However, to have an impact, carbon storage must be done at a much larger scale than current CO{sub 2} injection operations for enhanced oil recovery. It must also include injection into saline aquifers. An important characteristic of CO{sub 2} is its strong buoyancy--storage must be guaranteed to be sufficiently permanent to satisfy the very reason that CO{sub 2} is injected. This long-term aspect (hundreds to thousands of years) is not currently captured in legislation, even if the U.S. has a relatively well-developed regulatory framework to handle carbonmore » storage, especially in the operational short term. This report proposes a hierarchical approach to permitting in which the State/Federal Government is responsible for developing regional assessments, ranking potential sites (''General Permit'') and lessening the applicant's burden if the general area of the chosen site has been ranked more favorably. The general permit would involve determining in the regional sense structural (closed structures), stratigraphic (heterogeneity), and petrophysical (flow parameters such as residual saturation) controls on the long-term fate of geologically sequestered CO{sub 2}. The state-sponsored regional studies and the subsequent local study performed by the applicant will address the long-term risk of the particular site. It is felt that a performance-based approach rather than a prescriptive approach is the most appropriate framework in which to address public concerns. However, operational issues for each well (equivalent to the current underground injection control-UIC-program) could follow regulations currently in place. Area ranking will include an understanding of trapping modes. Capillary (due to residual saturation) and structural (due to local geological configuration) trappings are two of the four mechanisms (the other two are solubility and mineral trappings), which are the most relevant to the time scale of interest. The most likely pathways for leakage, if any, are wells and faults. We favor a defense-in-depth approach, in which storage permanence does not rely upon a primary seal only but assumes that any leak can be contained by geologic processes before impacting mineral resources, fresh ground water, or ground surface. We examined the Texas Gulf Coast as an example of an attractive target for carbon storage. Stacked sand-shale layers provide large potential storage volumes and defense-in-depth leakage protection. In the Texas Gulf Coast, the best way to achieve this goal is to establish the primary injection level below the total depth of most wells (>2,400 m-8,000 ft). In addition, most faults, particularly growth faults, present at the primary injection level do not reach the surface. A potential methodology, which includes an integrated approach comprising the whole chain of potential events from leakage from the primary site to atmospheric impacts, is also presented. It could be followed by the State/Federal Government, as well as by the operators.« less

Optimal joule heating of the subsurface

DOEpatents

Berryman, J.G.; Daily, W.D.

1994-07-05

A method for simultaneously heating the subsurface and imaging the effects of the heating is disclosed. This method combines the use of tomographic imaging (electrical resistance tomography or ERT) to image electrical resistivity distribution underground, with joule heating by electrical currents injected in the ground. A potential distribution is established on a series of buried electrodes resulting in energy deposition underground which is a function of the resistivity and injection current density. Measurement of the voltages and currents also permits a tomographic reconstruction of the resistivity distribution. Using this tomographic information, the current injection pattern on the driving electrodes can be adjusted to change the current density distribution and thus optimize the heating. As the heating changes conditions, the applied current pattern can be repeatedly adjusted (based on updated resistivity tomographs) to affect real time control of the heating.

Some engineering aspects of insulin delivery systems.

PubMed

Spencer, W J; Bair, R E; Carlson, G A; Love, J T; Urenda, R S; Eaton, R P; Schade, D S

1980-01-01

The characteristics of electronically controlled insulin delivery systems are presented. Early experiments with an external system have shown promise in providing improved glycemic control over conventional methods of single or multiple subcutaneous insulin injections. The encouraging results with external insulin delivery systems have led to the development and early testing in dogs of an implantable system with remote controls to permit variable insulin flow rates. A number of questions remain to be answered before widespread experimentation with external and implanted insulin delivery systems is possible. There appears to be no major development problems with the engineering aspects of such systems.

Public Notice: KYV0070

EPA Pesticide Factsheets

The U.S. Environmental Protection Agency, Region 4 intends to issue one Class 5 UIC permit to the Warrior Coal, LLC. This permit would cover six (6) mine-backfill injection wells located in Hopkins County, Kentucky.

Studies on Inhibition of Intestinal Absorption of Radioactive Strontium

PubMed Central

Skoryna, Stanley C.; Paul, T. M.; Edward, Deirdre Waldron

1964-01-01

A method is reported which permits selective suppression of absorption of radioactive strontium from ingested food material, permitting the calcium to be available to the body. Studies were carried out in vivo by injection of Sr89 and Ca45 in the presence of inert carrier into ligated intestinal segments in rats, and the amount of absorption was measured by standard monitoring techniques. The pattern of absorption of both ions is very similar but the rate of absorption is different. It was found that the polyelectrolyte, sodium alginate, obtained from brown algae (Phaeophyceae), injected simultaneously with radiostrontium effectively reduces the absortion of Sr89 from all segments of the intestine by as much as 50-80% of the control values. No significant reduction in absorption of Ca45 was observed in equivalent concentrations. The reduction in blood levels of Sr89 and in bone uptake corresponded to the absorption pattern. The difference in the effect on strontium and calcium absorption may be due to differences in the binding capacity of sodium alginate from the two metal ions under the conditions present in vivo. PMID:14180534

Toroidal reactor

DOEpatents

Dawson, John M.; Furth, Harold P.; Tenney, Fred H.

1988-12-06

Method for producing fusion power wherein a neutral beam is injected into a toroidal bulk plasma to produce fusion reactions during the time permitted by the slowing down of the particles from the injected beam in the bulk plasma.

A community based approach to linking injection drug users with needed services through pharmacies: An evaluation of a pilot intervention in New York City

PubMed Central

Rudolph, AE; Standish, K; Amesty, S; Crawford, ND; Stern, RJ; Badillo, WE; Boyer, A; Brown, D; Ranger, N; Orduna, JM Garcia; Lasenburg, L; Lippek, Sarah; Fuller, CM

2010-01-01

Studies suggest that community-based approaches could help pharmacies expand their public health role, particularly pertaining to HIV prevention. Thirteen pharmacies participating in New York’s Expanded Syringe Access Program, which permits non-prescription syringe sales to reduce syringe-sharing among injection drug users (IDUs), were enrolled in an intervention to link IDU syringe customers to medical/social services. Sociodemographics, injection practices, beliefs about and experiences with pharmacy use, and medical/social service utilization were compared among 29 IDUs purchasing syringes from intervention pharmacies and 66 IDUs purchasing syringes from control pharmacies using chi-square tests. Intervention IDUs reported more positive experiences in pharmacies than controls; both groups were receptive to a greater public health pharmacist role. These data provide evidence that CBPR aided in the implementation of a pilot structural intervention to promote understanding of drug use and HIV prevention among pharmacy staff, and facilitated expansion of pharmacy services beyond syringe sales in marginalized, drug-using communities. PMID:20528131

An egg injection technique to evaluate the effect of polychlorinated biphenyls on the hatching success of the snapping turtle (Chelydra serpentina serpentina).

PubMed

Schnars, Jeanette L; Voss, Margaret A; Stauffer, Jay R

2011-04-01

Embryos of oviparous organisms are exposed to contaminants by two pathways: contaminant uptake from the surrounding environment, and the transfer from female to offspring (maternal transfer). The initial source of contaminant exposure for most embryos is likely to be maternal transfer; therefore, maternal transfer studies are critical in determining the effects of contaminants on future populations. Injection of contaminants directly into eggs is one route of experimental contaminant exposure that permits controlled doses and potential reliable replication. This technique, however, has been used in the past with little success in reptiles. The objective of the present study was to evaluate egg injection as a means of mimicking maternal transfer of polychlorinated biphenyls (PCBs) to snapping turtle eggs. Eggs from several clutches were injected with a PCB solution and incubated at several temperatures and moisture levels to measure interactive effects of injection, environmental condition, and contaminant load on hatching success. The injection technique allowed for application of consistent and specific doses among replicates. Overall hatching success in this study was 61% and was as high as 71% within specific treatments. Hatching success was much higher in this study than in other studies using egg injections to mimic maternal transfer in chelonians and crocodilians. Copyright © 2010 SETAC.

40 CFR 146.23 - Operating, monitoring, and reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the injection phase of cyclic steam operations And recording of one observation of injection pressure...; (4) Maintenance of the results of all monitoring until the next permit review (see 40 CFR 144.52(a)(5...

40 CFR 146.23 - Operating, monitoring, and reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the injection phase of cyclic steam operations And recording of one observation of injection pressure...; (4) Maintenance of the results of all monitoring until the next permit review (see 40 CFR 144.52(a)(5...

40 CFR 146.23 - Operating, monitoring, and reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the injection phase of cyclic steam operations And recording of one observation of injection pressure...; (4) Maintenance of the results of all monitoring until the next permit review (see 40 CFR 144.52(a)(5...

40 CFR 146.23 - Operating, monitoring, and reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the injection phase of cyclic steam operations And recording of one observation of injection pressure...; (4) Maintenance of the results of all monitoring until the next permit review (see 40 CFR 144.52(a)(5...

40 CFR 147.2920 - Operating requirements for wells authorized by permit.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (c) Injection pressure at the wellhead shall be limited so that it does not initiate new fractures or propagate existing fractures in the confining zone adjacent to any UDSW. (d) Injection wells or projects...

40 CFR 147.2920 - Operating requirements for wells authorized by permit.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (c) Injection pressure at the wellhead shall be limited so that it does not initiate new fractures or propagate existing fractures in the confining zone adjacent to any UDSW. (d) Injection wells or projects...

40 CFR 147.2920 - Operating requirements for wells authorized by permit.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (c) Injection pressure at the wellhead shall be limited so that it does not initiate new fractures or propagate existing fractures in the confining zone adjacent to any UDSW. (d) Injection wells or projects...

40 CFR 147.2920 - Operating requirements for wells authorized by permit.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... (c) Injection pressure at the wellhead shall be limited so that it does not initiate new fractures or propagate existing fractures in the confining zone adjacent to any UDSW. (d) Injection wells or projects...

Fuel injection device and method

DOEpatents

Carlson, L.W.

1983-12-21

A fuel injection system and method provide for shaping a combustion plume within a combustion chamber to effectively recirculate hot combustion gases for stable combustion conditions while providing symmetrical combustion conditions. Char and molten slag are passed to the outer boundary layer to complete combustion of char while permitting initial substoichiometric combustion in a reductive atmosphere for reducing discharge of nitrogen oxides. Shaping of the plume is accomplished by an axially adjustable pintle which permits apportionment of driving pressure between elements which contribute tangential and those which contribute radial directional components to oxidant flow entering the combustion chamber.

Fuel injection device and method

DOEpatents

Carlson, Larry W.

1986-01-01

A fuel injection system and method provide for shaping a combustion plume within a combustion chamber to effectively recirculate hot combustion gases for stable combustion conditions while providing symmetrical combustion conditions. Char and molten slag are passed to the outer boundary layer to complete combustion of char while permitting initial substoichiometric combustion in a reductive atmosphere for reducing discharge of nitrogen oxides. Shaping of the plume is accomplished by an axially adjustable pintle which permits apportionment of driving pressure between elements which contribute tangential and those which contribute radial directional components to oxidant flow entering the combustion chamber.

Fuel injection device and method

DOEpatents

Carlson, Larry W.

1986-02-04

A fuel injection system and method provide for shaping a combustion plume within a combustion chamber to effectively recirculate hot combustion gases for stable combustion conditions while providing symmetrical combustion conditions. Char and molten slag are passed to the outer boundary layer to complete combustion of char while permitting initial substoichiometric combustion in a reductive atmosphere for reducing discharge of nitrogen oxides. Shaping of the plume is accomplished by an axially adjustable pintle which permits apportionment of driving pressure between elements which contribute tangential and those which contribute radial directional components to oxidant flow entering the combustion chamber.

Edible Oil Barriers for Treatment of Chlorinated Solvent and Perchlorate-Contaminated Groundwater

DTIC Science & Technology

2010-02-01

This page left blank intentionally. 9 3.0 TECHNOLOGY The emulsified oil technology is a low- cost process for delivering a low solubility, slowly...associated with the actual injection process , including costs for installing the injection and monitoring wells, purchasing the substrate for injection...large area can be significantly lower due to economies of scale during injection and the relatively lower design, permitting, and monitoring costs

Characterization and design of the FutureGen 2.0 carbon storage site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilmore, Tyler; Bonneville, Alain; Sullivan, Charlotte

2016-10-01

The objective of the FutureGen 2.0 Project was to demonstrate, at the commercial scale, the technical feasibility of implementing carbon capture and storage (CCS) in a deep saline formation in Illinois, USA. Over approximately 5 years, the FutureGen Alliance conducted a detailed site-selection process and identified a site for carbon sequestration storage in Morgan County, Illinois. The storage site was fully characterized, including the collection of seismic data and the drilling and characterization of a stratigraphic borehole. The characterization data provided critical input for developing a site-specific conceptual model and subsequent numerical modeling simulations. The modeling simulations, coupled with themore » upstream designs of the pipeline and power plant supported the development of a detailed 90 percent design that included the injection wells and associated control and monitoring infrastructure. Collectively, all these data were used by the FutureGen Alliance to develop the required documentation to support the applications for four underground injection control (UIC) permits (one for each proposed well). In August 2014, the U.S. Environmental Protection Agency issued four, first-of-their-kind, Class VI UIC permits for carbon sequestration in the United States to the FutureGen Alliance. The information and data generated under this project have been made publically available through reports and publications, including this journal and others.« less

Supplementary routes to local anaesthesia.

PubMed

Meechan, J G

2002-11-01

The satisfactory provision of many dental treatments, particularly endodontics, relies on achieving excellent pain control. Unfortunately, the administration of a local anaesthetic solution does not always produce satisfactory anaesthesia of the dental pulp. This may be distressing for both patient and operator. Fortunately, failure of local anaesthetic injections can be overcome. This is often achieved by using alternative routes of approach for subsequent injections. Nerves such as the inferior alveolar nerve can be anaesthetized by a variety of block methods. However, techniques of anaesthesia other than the standard infiltration and regional block injections may be employed successfully when these former methods have failed to produce adequate pain control. This paper describes some supplementary local anaesthetic techniques that may be used to achieve pulpal anaesthesia for endodontic procedures when conventional approaches have failed. Although some of these techniques can be used as the primary form of anaesthesia, these are normally employed as 'back-up'. The methods described are intraligamentary (periodontal ligament) injections, intraosseous anaesthesia and the intrapulpal approach. The factors that influence the success of these methods and the advantages and disadvantages of each technique are discussed. The advent of new instrumentation, which permits the slow delivery of local anaesthetic solution has led to the development of novel methods of anaesthesia in dentistry. These new approaches are discussed.

IRRADIATION AND TISSUE IMMUNITY. II. RESPONSE TO INJECTION OF STAPHYLOCOCCI IN X IRRADIATED SKIN AREAS OF RABBITS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kahn, R.L.

1963-03-01

Twenty-four hrs after 1000-r x irradiation of a small area of the skin of rabbits, they were injected with a suspension of staphylococci subcutaneously in the irradiated area and in a nonirradiated control area. Localized lesions were most marked in nonirradiated areas and in some animals no visible lesions were noted in irradiated areas. The mild inflammatory lesions in irradiated areas corroborate the point of view, that irradiation is anti-inflammatory. The reason for mild lesions must be the reduced localization of staphylococci in irradiated areas and their escape from those areas. It is suggested that the antilocalizing property of irradiationmore » is probably the basis for the antiinflammatory action. When the concentration of organisms injected in the irradiated area was high (10 billion), septicemia and death of the rabbits occurred, presumably as a result of the antilocalizing property of irradiation, which permitted the escape of the organisms from the injected area. In animals injected in irradiated areas with either 0.5 or 5 billion organisms, no septicemia was observed, presumably because of the high natural immunity of rabbits to staphylococci. (TCO)« less

Lime Juice and Vinegar Injections as a Cheap and Natural Alternative to Control COTS Outbreaks.

PubMed

Moutardier, Grégoire; Gereva, Sompert; Mills, Suzanne C; Adjeroud, Mehdi; Beldade, Ricardo; Ham, Jayven; Kaku, Rocky; Dumas, Pascal

2015-01-01

Outbreaks of the corallivorous crown-of-thorns seastar Acanthaster planci (COTS) represent one of the greatest disturbances to coral reef ecosystems in the Indo-Pacific, affecting not only coral reefs but also the coastal communities which rely on their resources. While injection approaches are increasingly used in an attempt to control COTS densities, most of them display severe drawbacks including logistical challenges, high residual environmental impacts or low cost-effectiveness. We tested a new alternative control method based upon acidic injections of cheap, 100% natural products. We investigated the lethal doses, intra- and inter-specific disease transmission and immune responses of COTS when injected with fresh lime juice (extracted from local Citrus arantifolia) and white spirit vinegar. High COTS mortality was achieved with small volumes: 10-20 ml per seastar induced death in 89%/97% of injected specimens after an average 34.3 h/29.8 h for lime juice and vinegar respectively. Highest efficiency was reached for both solutions with double shots of (2 × 10 ml) in two different areas on the body: 100% mortality occurred within 12-24 h, which is similar or faster compared with other current injection methods. Multiple immune measures suggested that death was very likely caused by pH stress from the acidic solutions rather than a bacterial infection. Contagion to either conspecifics or a variety of other reef species was not observed, even at COTS densities 15 times higher than the highest naturally reported. 10 to 20 l lime juice/vinegar could kill up to a thousand COTS at a cost of less than 0.05 USD per specimen; no permits or special handling procedures are required. We conclude that injections of lime juice and vinegar offer great advantages when compared to current best practises and constitute a cheap and natural option for all reefs affected by COTS.

Lime Juice and Vinegar Injections as a Cheap and Natural Alternative to Control COTS Outbreaks

PubMed Central

Moutardier, Grégoire; Gereva, Sompert; Mills, Suzanne C.; Adjeroud, Mehdi; Beldade, Ricardo; Ham, Jayven; Kaku, Rocky; Dumas, Pascal

2015-01-01

Outbreaks of the corallivorous crown-of-thorns seastar Acanthaster planci (COTS) represent one of the greatest disturbances to coral reef ecosystems in the Indo-Pacific, affecting not only coral reefs but also the coastal communities which rely on their resources. While injection approaches are increasingly used in an attempt to control COTS densities, most of them display severe drawbacks including logistical challenges, high residual environmental impacts or low cost-effectiveness. We tested a new alternative control method based upon acidic injections of cheap, 100% natural products. We investigated the lethal doses, intra- and inter-specific disease transmission and immune responses of COTS when injected with fresh lime juice (extracted from local Citrus arantifolia) and white spirit vinegar. High COTS mortality was achieved with small volumes: 10–20 ml per seastar induced death in 89%/97% of injected specimens after an average 34.3 h/29.8 h for lime juice and vinegar respectively. Highest efficiency was reached for both solutions with double shots of (2 × 10 ml) in two different areas on the body: 100% mortality occurred within 12–24 h, which is similar or faster compared with other current injection methods. Multiple immune measures suggested that death was very likely caused by pH stress from the acidic solutions rather than a bacterial infection. Contagion to either conspecifics or a variety of other reef species was not observed, even at COTS densities 15 times higher than the highest naturally reported. 10 to 20 l lime juice/vinegar could kill up to a thousand COTS at a cost of less than 0.05 USD per specimen; no permits or special handling procedures are required. We conclude that injections of lime juice and vinegar offer great advantages when compared to current best practises and constitute a cheap and natural option for all reefs affected by COTS. PMID:26356840

[Bruxism, temporo-mandibular dysfunction and botulinum toxin].

PubMed

Chikhani, L; Dichamp, J

2003-07-01

Tooth grinding and tooth clenching are unvoluntary mainly nocturnal habits that result in an hypertrophy of masseter and temporalis muscles with an unbalance between opening and closing muscles of the jaw and lead to an alteration of mandibular condyles movements and to hyper pressure in the temporo-mandibular joints (TMJ) which can generate severe pain. Intra muscular injections of botulinum toxin permit to restablish the balance between closing and opening muscles, to relieve pain, to treat masseteric hypertrophy with improvement of face outline and to recover a normal cinetic of temporo-mandibular joints. Moreover, botulinum toxin injections permit to quit habits of tooth grinding and clenching and one single session of injections is curative for 2/3 of the patients. There are no side effects apart from slight diffusion to superficial muscles of the face resulting in a "fixed" smile for about 6 to 8 weeks. So injections of botulinum toxin in masseter and temporalis muscles are an efficient treatment of bruxism and TMJ dysfunction, cheap with no lasting side effect.

A totally phosphine-free synthesis of metal telluride nanocrystals by employing alkylamides to replace alkylphosphines for preparing highly reactive tellurium precursors.

PubMed

Yao, Dong; Liu, Yi; Zhao, Wujun; Wei, Haotong; Luo, Xintao; Wu, Zhennan; Dong, Chunwei; Zhang, Hao; Yang, Bai

2013-10-21

Despite the developments in the wet chemical synthesis of high-quality semiconductor nanocrystals (NCs) with diverse elemental compositions, telluride NCs are still irreplaceable materials owing to their excellent photovoltaic and thermoelectric performances. Herein we demonstrate the dissolution of elemental tellurium (Te) in a series of alkylamides by sodium borohydride (NaBH4) reduction at relatively low temperature to produce highly reactive precursors for hot-injection synthesis of telluride NCs. The capability to tune the reactivity of Te precursors by selecting injection temperature permits control of NC size over a broad range. The current preparation of Te precursors is simple, economical, and totally phosphine-free, which will promote the commercial synthesis and applications of telluride NCs.

Intracerebroventricular morphine for refractory cancer pain: transitioning to the home setting.

PubMed

Adolph, Michael D; Stretanski, Michael F; McGregor, John M; Rawn, Bonnie L; Ross, Patrick M; Benedetti, Costantino

2010-08-01

Refractory cancer pain may be effectively controlled by titrating intracerebroventricular (ICV) preservative-free opioid. In this case report, a continuous infusion of ICV morphine permitted our patient with lung cancer and painful spinal metastases to be discharged to home hospice with family. The approach exploits the high potency of morphine injected into cerebrospinal fluid (CSF). Sterile, injectable, preservative-free morphine is directly infused into CSF through a subcutaneous Ommaya reservoir placed under the scalp by a neurosurgeon, with an attached catheter passed through a burr hole in the skull with its tip in a cerebral ventricle. Although investigators have described home care of patients receiving intraspinal analgesics, no report describes the process of transitioning the patient receiving continuous ICV morphine infusion to the home setting.

40 CFR 144.52 - Establishing permit conditions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... comply with the financial responsibility requirements of subpart F of this part. (8) Mechanical integrity. A permit for any Class I, II or III well or injection project which lacks mechanical integrity shall... Administrator. (6) After a cessation of operations of two years the owner or operator shall plug and abandon the...

40 CFR 144.52 - Establishing permit conditions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the financial responsibility requirements set forth in § 146.85 of this chapter. (8) Mechanical integrity. A permit for any Class I, II, III or VI well or injection project which lacks mechanical... cessation of operations of two years the owner or operator shall plug and abandon the well in accordance...

40 CFR 144.52 - Establishing permit conditions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the financial responsibility requirements set forth in § 146.85 of this chapter. (8) Mechanical integrity. A permit for any Class I, II, III or VI well or injection project which lacks mechanical... cessation of operations of two years the owner or operator shall plug and abandon the well in accordance...

40 CFR 144.52 - Establishing permit conditions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the financial responsibility requirements set forth in § 146.85 of this chapter. (8) Mechanical integrity. A permit for any Class I, II, III or VI well or injection project which lacks mechanical... cessation of operations of two years the owner or operator shall plug and abandon the well in accordance...

40 CFR 144.52 - Establishing permit conditions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the financial responsibility requirements set forth in § 146.85 of this chapter. (8) Mechanical integrity. A permit for any Class I, II, III or VI well or injection project which lacks mechanical... cessation of operations of two years the owner or operator shall plug and abandon the well in accordance...

Microencapsulation Of Living Cells

NASA Technical Reports Server (NTRS)

Chang, Manchium; Kendall, James M.; Wang, Taylor G.

1989-01-01

In experimental technique, living cells and other biological materials encapsulated within submillimeter-diameter liquid-filled spheres. Sphere material biocompatible, tough, and compliant. Semipermeable, permitting relatively small molecules to move into and out of sphere core but preventing passage of large molecules. New technique promises to make such spherical capsules at high rates and in uniform, controllable sizes. Capsules injected into patient through ordinary hypodermic needle. Promising application for technique in treatment of diabetes. Also used to encapsulate pituitary cells and thyroid hormone adrenocortical cells for treatment of other hormonal disorders, to encapsulate other secreting cells for transplantation, and to package variety of pharmaceutical products and agricultural chemicals for controlled release.

40 CFR 146.91 - Reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... any event that exceeds operating parameters for annulus pressure or injection pressure specified in the permit; (4) A description of any event which triggers a shut-off device required pursuant to § 146... plugging reports, post-injection site care data, including, if appropriate, data and information used to...

Viscosity of materials for laryngeal injection: a review of current knowledge and clinical implications.

PubMed

Lisi, Christopher; Hawkshaw, Mary J; Sataloff, Robert T

2013-01-01

Over the past several decades, researchers have sought the ideal substances for use in injection laryngoplasty. This search has inspired several basic science studies centering on the viscoelastic properties of popularly used injectables as well as of experimental substances. Unfortunately, these studies have used various techniques and different units for measuring viscosity. For clinical purposes, there has been a need for a concise compilation of these data, converted into consistent units, to permit easy comparison of the reported viscosities of various substances. The literature has been reviewed to address this need. Scholarly review. Comparable data are available for various substances, including vocal fold mucosa, subcutaneous fat, bovine dermal collagen, glutaraldehyde cross-linked collagen, polytetrafluoroethylene, and hyaluronic acid products. The values for difference substances vary widely. There appears to be a growing body of useful knowledge about viscosity of substances used for medial (vibratory margin) injection. However, decisions regarding viscosity of substances for lateral injection medialization appear to have been made without the benefit of evidence-based research. It is possible that the trend toward relatively low viscosity materials for lateral injection is based on ease of surgical use through a small needle, but that the low viscosity may adversely affect the control over the position of the injected substance. Research is needed comparing viscosity with predictability of surgical deposition of injected substances. Copyright © 2013 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

40 CFR 147.2918 - Permit application information.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., including total dissolved solids, chlorides, and additives. (4) Geologic data on the injection and confining..., showing: (i) Total depth or plug-back depth; (ii) Depth to top and bottom of injection interval; (iii) Depths to tops and bottoms of casing and cemented intervals, and amount of cement to be used; (iv) Size...

40 CFR 147.2918 - Permit application information.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., including total dissolved solids, chlorides, and additives. (4) Geologic data on the injection and confining..., showing: (i) Total depth or plug-back depth; (ii) Depth to top and bottom of injection interval; (iii) Depths to tops and bottoms of casing and cemented intervals, and amount of cement to be used; (iv) Size...

40 CFR 147.2918 - Permit application information.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., including total dissolved solids, chlorides, and additives. (4) Geologic data on the injection and confining..., showing: (i) Total depth or plug-back depth; (ii) Depth to top and bottom of injection interval; (iii) Depths to tops and bottoms of casing and cemented intervals, and amount of cement to be used; (iv) Size...

40 CFR 147.2918 - Permit application information.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., including total dissolved solids, chlorides, and additives. (4) Geologic data on the injection and confining..., showing: (i) Total depth or plug-back depth; (ii) Depth to top and bottom of injection interval; (iii) Depths to tops and bottoms of casing and cemented intervals, and amount of cement to be used; (iv) Size...

40 CFR 144.51 - Conditions applicable to all permits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... used to complete the application for this permit, for a period of at least 3 years from the date of the... any time; and (ii) The nature and composition of all injected fluids until three years after the... shall continue to retain the records after the three year retention period unless he delivers the...

40 CFR 144.51 - Conditions applicable to all permits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... used to complete the application for this permit, for a period of at least 3 years from the date of the... any time; and (ii) The nature and composition of all injected fluids until three years after the... shall continue to retain the records after the three year retention period unless he delivers the...

40 CFR 144.51 - Conditions applicable to all permits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... used to complete the application for this permit, for a period of at least 3 years from the date of the... any time; and (ii) The nature and composition of all injected fluids until three years after the... shall continue to retain the records after the three year retention period unless he delivers the...

40 CFR 144.51 - Conditions applicable to all permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... used to complete the application for this permit, for a period of at least 3 years from the date of the... any time; and (ii) The nature and composition of all injected fluids until three years after the... shall continue to retain the records after the three year retention period unless he delivers the...

40 CFR 144.51 - Conditions applicable to all permits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... used to complete the application for this permit, for a period of at least 3 years from the date of the... any time; and (ii) The nature and composition of all injected fluids until three years after the... shall continue to retain the records after the three year retention period unless he delivers the...

40 CFR 145.11 - Requirements for permitting.

Code of Federal Regulations, 2014 CFR

2014-07-01

...)-(Confidential information); (2) Section 144.6—(Classification of injection wells); (3) Section 144.7... movement of fluids into underground sources of drinking water); (7) Section 144.13—(Elimination of Class IV...—(Authorization by rule); (10) Section 144.31—(Application for a permit); (11) Section 144.32—(Signatories); (12...

40 CFR 145.11 - Requirements for permitting.

Code of Federal Regulations, 2013 CFR

2013-07-01

...)-(Confidential information); (2) Section 144.6—(Classification of injection wells); (3) Section 144.7... movement of fluids into underground sources of drinking water); (7) Section 144.13—(Elimination of Class IV...—(Authorization by rule); (10) Section 144.31—(Application for a permit); (11) Section 144.32—(Signatories); (12...

40 CFR 145.11 - Requirements for permitting.

Code of Federal Regulations, 2011 CFR

2011-07-01

...)-(Confidential information); (2) Section 144.6—(Classification of injection wells); (3) Section 144.7... movement of fluids into underground sources of drinking water); (7) Section 144.13—(Elimination of Class IV...—(Authorization by rule); (10) Section 144.31—(Application for a permit); (11) Section 144.32—(Signatories); (12...

40 CFR 145.11 - Requirements for permitting.

Code of Federal Regulations, 2010 CFR

2010-07-01

...)-(Confidential information); (2) Section 144.6—(Classification of injection wells); (3) Section 144.7... movement of fluids into underground sources of drinking water); (7) Section 144.13—(Elimination of Class IV...—(Authorization by rule); (10) Section 144.31—(Application for a permit); (11) Section 144.32—(Signatories); (12...

40 CFR 145.11 - Requirements for permitting.

Code of Federal Regulations, 2012 CFR

2012-07-01

...)-(Confidential information); (2) Section 144.6—(Classification of injection wells); (3) Section 144.7... movement of fluids into underground sources of drinking water); (7) Section 144.13—(Elimination of Class IV...—(Authorization by rule); (10) Section 144.31—(Application for a permit); (11) Section 144.32—(Signatories); (12...

Resonant circuit which provides dual frequency excitation for rapid cycling of an electromagnet

DOEpatents

Praeg, Walter F.

1984-01-01

Disclosed is a ring magnet control circuit that permits synchrotron repetition rates much higher than the frequency of the cosinusoidal guide field of the ring magnet during particle acceleration. the control circuit generates cosinusoidal excitation currents of different frequencies in the half waves. During radio frequency acceleration of the particles in the synchrotron, the control circuit operates with a lower frequency cosine wave and thereafter the electromagnets are reset with a higher frequency half cosine wave. Flat-bottom and flat-top wave shaping circuits maintain the magnetic guide field in a relatively time-invariant mode during times when the particles are being injected into the ring magnets and when the particles are being ejected from the ring magnets.

Method and apparatus for spraying molten materials

DOEpatents

Glovan, R.J.; Tierney, J.C.; McLean, L.L.; Johnson, L.L.; Nelson, G.L.; Lee, Y.M.

1996-06-25

A metal spray apparatus is provided with a supersonic nozzle. Molten metal is injected into a gas stream flowing through the nozzle under pressure. By varying the pressure of the injected metal, the droplet can be made in various selected sizes with each selected size having a high degree of size uniformity. A unique one piece graphite heater provides easily controlled uniformity of temperature in the nozzle and an attached tundish which holds the pressurized molten metal. A unique U-shaped gas heater provides extremely hot inlet gas temperatures to the nozzle. A particularly useful application of the spray apparatus is coating of threads of a fastener with a shape memory alloy. This permits a fastener to be easily inserted and removed but provides for a secure locking of the fastener in high temperature environments. 12 figs.

40 CFR 147.3005 - Radioactive waste injection wells.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Radioactive waste injection wells. 147... wells. Notwithstanding §§ 144.24 and 146.51(b) of this chapter, owners and operators of wells used to... permitting requirements pertaining to Class I wells in parts 124, 144 and 146 of this chapter, as modified...

Deep anterior lamellar keratoplasty: dissection plane with viscoelastic and air can be different.

PubMed

Ross, Andrew R; Said, Dalia G; El-Amin, Abdalla; Altaan, Saif; Cabrerizo, Javier; Nubile, Mario; Hogan, Emily; Mastropasqua, Leonardo; Dua, Harminder Singh

2018-04-03

To investigate and define the nature of big bubbles (BB) formed by injection of viscoelastic in deep anterior lamellar keratoplasty. Intrastromal injections of 0.1 and 0.3 mL of sodium hyaluronate 1.2% and 0.6% were made into sclera-corneal discs (n = 32) at superficial (anterior-third), midstromal (middle-third) and deep (posterior-third) levels to simulate deep anterior lamellar keratoplasty. Postinjection optical coherence tomograms (OCT) were obtained with the needle in situ. The samples were sectioned and examined histologically. Twelve control samples were injected with air. With superficial injections (n=8) only intrastromal accumulation of viscoelastic was noted. With midstromal injections (n=10) intrastromal accumulation of viscoelastic (n=6) and intrastromal big bubbles (IBB) (n=4) with substantial and variable stromal tissue in the walls were noted. No type 1, type 2 or mixed BB were noted. With deep injections (n=14), type 1 BB (n=4), IBB (n=4) and mixed BB (n=6) were obtained.There was no difference in the results with the two different concentrations of viscoelastic used. With air injection (n=12), 10 type 1 and 1 type 2 BB and 1 mixed BB were obtained. No IBB was noted. BB obtained by injection of viscoelastic and air can be different. The former tends to occur at the site of injection, especially with midstromal injections, takes the form of tissue separation by stretch and tearing and does not cleave in a consistent plane like air. Surgeons should be aware of IBB created by viscodissection and not confuse it for a type1 BB. Intraoperative OCT should help identify IBB. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Free-hand ultrasound guidance permits safe and efficient minimally invasive intrathymic injections in both young and aged mice

PubMed Central

Tuckett, Andrea Z.; Zakrzewski, Johannes L.; Li, Duan; van den Brink, Marcel R.M.; Thornton, Raymond H.

2014-01-01

The goal of this study was to evaluate whether using an aseptic free-hand approach for ultrasound-guided injection facilitates injection into the thymic gland in mice. We used this interventional radiology technique in young, aged, and immunodeficient mice and found that the thymus was visible in all cases. The mean injection period was 8 s in young mice and 19 s in aged or immunodeficient mice. Injection accuracy was confirmed by intrathymic location of an injected dye, or by in vivo bioluminescence imaging of injected luciferase-expressing cells. Accurate intrathymic injection was confirmed in 97% of cases. No major complications were observed. We conclude that an aseptic free-hand technique for ultrasound-guided intrathymic injection is safe, accurate, and reduces the time required for intrathymic injections. This method facilitates large-scale experiments, injection of individual thymic lobes, and is clinically relevant. PMID:25701534

Use of off-axis injection as an alternative to geometrically merging beams in an energy-recovering linac

DOEpatents

Douglas, David R [York County, VA

2012-01-10

A method of using off-axis particle beam injection in energy-recovering linear accelerators that increases operational efficiency while eliminating the need to merge the high energy re-circulating beam with an injected low energy beam. In this arrangement, the high energy re-circulating beam and the low energy beam are manipulated such that they are within a predetermined distance from one another and then the two immerged beams are injected into the linac and propagated through the system. The configuration permits injection without geometric beam merging as well as decelerated beam extraction without the use of typical beamline elements.

Dust particle injector for hypervelocity accelerators provides high charge-to-mass ratio

NASA Technical Reports Server (NTRS)

Berg, O. E.

1966-01-01

Injector imparts a high charge-to-mass ratio to microparticles and injects them into an electrostatic accelerator so that the particles are accelerated to meteoric speeds. It employs relatively large masses in the anode and cathode structures with a relatively wide separation, thus permitting a large increase in the allowable injection voltages.

40 CFR 144.84 - Do I need to get a permit?

Code of Federal Regulations, 2010 CFR

2010-07-01

... V injection activity is “authorized by rule,” meaning you have to comply with all the requirements... Class V well is no longer authorized by rule. This means that you have to either get a permit or close... authorization expires once you have properly closed your well, as described in § 144.82(b). (b) Circumstances in...

Metal spray apparatus with a U-shaped electric inlet gas heater and a one-piece electric heater surrounding a nozzle

DOEpatents

Glovan, Ronald J.; Tierney, John C.; McLean, Leroy L.; Johnson, Lawrence L.; Verbael, David J.

1995-01-01

An electrically heated metal spray apparatus is provided with a supersonic nozzle. Molten metal is injected into a gas stream flowing through the nozzle under pressure. By varying the pressure of the injected metal, the droplet can be made in various selected sizes with each selected size having a high degree of size uniformity. A unique one piece graphite heater provides easily controlled uniformity of temperature in the nozzle and an attached tundish which holds the pressurized molten metal. A unique U-shaped gas heater provides extremely hot inlet gas temperatures to the nozzle. A particularly useful application of the spray apparatus is coating of threads of a fastener with a shape memory alloy. This permits a fastener to be easily inserted and removed but provides for a secure locking of the fastener in high temperature environments.

Metal spray apparatus with a U-shaped electric inlet gas heater and a one-piece electric heater surrounding a nozzle

DOEpatents

Glovan, R.J.; Tierney, J.C.; McLean, L.L.; Johnson, L.L.; Verbael, D.J.

1995-10-17

An electrically heated metal spray apparatus is provided with a supersonic nozzle. Molten metal is injected into a gas stream flowing through the nozzle under pressure. By varying the pressure of the injected metal, the droplet can be made in various selected sizes with each selected size having a high degree of size uniformity. A unique one piece graphite heater provides easily controlled uniformity of temperature in the nozzle and an attached tundish which holds the pressurized molten metal. A unique U-shaped gas heater provides extremely hot inlet gas temperatures to the nozzle. A particularly useful application of the spray apparatus is coating of threads of a fastener with a shape memory alloy. This permits a fastener to be easily inserted and removed but provides for a secure locking of the fastener in high temperature environments. 12 figs.

HSP-70 as a nonspecific early marker in cisplatin ototoxicity.

PubMed

Ramírez-Camacho, R; Citores, M J; Trinidad, A; Verdaguer, J M; García-Berrocal, J R; Marero, A Martín; Puente, A; González-García, J A; Vargas, J A

2007-06-01

The great variety of pathological entities related to the presence of circulating HSP-70 suggests a nonspecific cellular damage. As the present study shows, positive results decrease with respect to the time elapsed after the injection of the ototoxic agent. HSP-70 appears as an early and transient marker that could permit early detection of inner ear damage. The aim of this study was to determine the presence of HSP-70 at different time points by means of Western blot immunoassay in the sera of rats treated with cisplatin. Thirty-six Wistar rats were intraperitoneally injected with cisplatin at a dose of 5 mg/kg and blood samples were collected at 7 and 90 days. Determination of HSP-70 was made by means of a modified Western blot immunoassay kit originally used for human HSP-70 antigen detection. A control group of 18 animals was used for comparison. Western blot was positive in 77.8% of the animals in the 7 days group, decreasing to a 44.4% in the 90 days group. In the control group, Western blot was positive in 5.5%.

The Effect of the Air-Delivery Method on Parameters of the Precessing Vortex Core in a Hydrodynamic Vortex Chamber

NASA Astrophysics Data System (ADS)

Alekseenko, S. V.; Shtork, S. I.; Yusupov, R. R.

2018-03-01

The effect of the method of gas-phase injection into a swirled fluid flow on parameters of a precessing vortex core is studied experimentally. Conditions of the appearance of the vortex-core precession effect were modeled in a hydrodynamic sudden expansion vortex chamber. The dependences of the vortexcore precession frequency, flow-pulsation level, and full pressure differential in the vortex chamber on the consumption gas content in the flow have been obtained. The results of measurements permit one to determine optimum conditions for the most effective control of vortex-core precession.

Free-hand ultrasound guidance permits safe and efficient minimally invasive intrathymic injections in both young and aged mice.

PubMed

Tuckett, Andrea Z; Zakrzewski, Johannes L; Li, Duan; van den Brink, Marcel R M; Thornton, Raymond H

2015-04-01

The goal of this study was to evaluate whether use of an aseptic free-hand approach to ultrasound-guided injection facilitates injection into the thymic gland in mice. We used this interventional radiology technique in young, aged and immunodeficient mice and found that the thymus was visible in all cases. The mean injection period was 8 seconds in young mice and 19 seconds in aged or immunodeficient mice. Injection accuracy was confirmed by intrathymic location of an injected dye or by in vivo bioluminescence imaging of injected luciferase-expressing cells. Accurate intrathymic injection was confirmed in 97% of cases. No major complications were observed. We conclude that an aseptic freehand technique for ultrasound-guided intrathymic injection is safe and accurate and reduces the time required for intrathymic injections. This method facilitates large-scale experiments and injection of individual thymic lobes and is clinically relevant. Copyright © 2015 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

Antibiotics in surgical treatment of acute abscesses.

PubMed Central

Blick, P W; Flowers, M W; Marsden, A K; Wilson, D H; Ghoneim, A T

1980-01-01

A four-way, double-blind, prospective trial of treatment of abscesses by incision, curettage, and primary closure with and without antibiotic cover (clindamycin injection before operation or capsules after operation, or both) was conducted. There was no appreciable difference in mean healing time between the patients given both the antibiotic injection and the antibiotic capsules and those given the injection and placebo capsules, whereas healing times in those given the placebo injection and antibiotic capsules or placebo only were appreciably longer. Four of the patients who were not given the antibiotic injection developed bacteraemia; one patient who was given the antibiotic injection also developed a bacteraemia, but this was caused by clindamycin-resistant bacteria. These results show that a single injection of an effective antibiotic before operation is sufficient to protect the patient against bacteraemia and permit optimum healing. PMID:7000250

Fluid sampling apparatus and method

DOEpatents

Yeamans, David R.

1998-01-01

Incorporation of a bellows in a sampling syringe eliminates ingress of contaminants, permits replication of amounts and compression of multiple sample injections, and enables remote sampling for off-site analysis.

75 FR 73000 - Corporate Credit Unions

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-29

... suitable only when it: Is free from bias; Permits reasonably consistent qualitative and quantitative... injections and launched liquidity and share guarantee programs designed to stabilize the corporate system and...

Modeling of the Temperature Field Recovery in the Oil Pool

NASA Astrophysics Data System (ADS)

Khabibullin, I. L.; Davtetbaev, A. Ya.; Mar'in, D. F.; Khisamov, A. A.

2018-05-01

This paper considers the problem on mathematical modeling of the temperature field recovery in the oil pool upon termination of injection of water into the pool. The problem is broken down into two stages: injection of water and temperature and pressure recovery upon termination of injection. A review of the existing mathematical models is presented, analytical solutions for a number of cases have been constructed, and a comparison of the analytical solutions of different models has been made. In the general form, the expression has been obtained that permits determining the temperature change in the oil pool upon termination of injection of water (recovery of the temperature field).

Effects of chemogenetic excitation or inhibition of the ventrolateral periaqueductal gray on the acquisition and extinction of Pavlovian fear conditioning.

PubMed

Arico, Carolyn; Bagley, Elena E; Carrive, Pascal; Assareh, Neda; McNally, Gavan P

2017-10-01

The midbrain periaqueductal gray (PAG) has been implicated in the generation and transmission of a prediction error signal that instructs amygdala-based fear and extinction learning. However, the PAG also plays a key role in the expression of conditioned fear responses. The evidence for a role of the PAG in fear learning and extinction learning has been obtained almost exclusively using PAG-dependent fear responses. It is less clear whether the PAG regulates fear learning when other measures of learned fear are used. Here we combined a chemogenetic approach, permitting excitation or inhibition of neurons in the ventrolateral PAG (VLPAG), with conditioned suppression as the measure of learned fear to assess the role of VLPAG in the acquisition and extinction of fear learning. We show that chemogenetic excitation of VLPAG (with some encroachment on lateral PAG [LPAG]) impairs acquisition of fear and, conversely, chemogenetic inhibition impairs extinction of fear. These effects on fear and extinction learning were specific to the combination of DREADD expression and injection of CNO because they were observed relative to both eYFP controls injected with CNO as well as DREADD expressing controls injected with vehicle. Taken together, these results show that activity of L/VLPAG neurons regulates both the acquisition and extinction of Pavlovian fear learning. Copyright © 2017 Elsevier Inc. All rights reserved.

Optimum instantaneous impulsive orbital injection to attain a specified asymptotic velocity vector.

NASA Technical Reports Server (NTRS)

Bean, W. C.

1971-01-01

A nalysis of the necessary conditions of Battin for instantaneous orbital injection, with consideration of the uniqueness of his solution, and of the further problem which arises in the degenerate case when radius vector and asymptotic vector are separated by 180 deg. It is shown that when the angular separation between radius vector and asymptotic velocity vector satisfies theta not equal to 180 deg, there are precisely two insertion-velocity vectors which permit attainment of the target asymptotic velocity vector, one yielding posigrade, the other retrograde motion. When theta equals to 180 deg, there is a family of insertion-velocity vectors which permit attainment of a specified asymptotic velocity vector with a unique insertion-velocity vector for every arbitrary orientation of a target unit angular momentum vector.

Mujer Mas Segura (Safer Women): a combination prevention intervention to reduce sexual and injection risks among female sex workers who inject drugs.

PubMed

Vera, Alicia; Abramovitz, Daniela; Lozada, Remedios; Martinez, Gustavo; Rangel, M Gudelia; Staines, Hugo; Patterson, Thomas L; Strathdee, Steffanie A

2012-08-14

Female sex workers who inject drugs (FSW-IDUs) are at risk of acquiring HIV, sexually transmitted infections (STI) and blood-borne infections through unprotected sex and sharing injection equipment. We conducted a 2×2 factorial randomized controlled trial to evaluate combination interventions to simultaneously reduce sexual and injection risks among FSW-IDUs in Tijuana and Ciudad Juarez, Mexico. FSW-IDUs ≥18 years reporting sharing injection equipment and unprotected sex with clients within the last month were randomized to one of four conditions based on an a priori randomization schedule, blinding interviewer/counselors to assignment. Due to the extreme vulnerability of this population, we did not include a control group that would deny some women access to preventive information. All women received similar information regardless of group allocation; the difference was in the way the information was delivered and the extent to which women had an interactive role. Each condition was a single 60-minute session, including either an interactive or didactic version of an injection risk intervention and sexual risk intervention. Women underwent interviewer-administered surveys and testing for HIV, syphilis, gonorrhea, Chlamydia, and Trichomonas at baseline and quarterly for 12 months. Combined HIV/STI incidence will be the primary outcome. Secondary outcomes are proportionate reductions in sharing of injection equipment and unprotected sex with clients. Of 1,132 women, 548 (48.4%) were excluded (88.9% were ineligible; 11.1% refused to participate or did not return); 584 eligible women enrolled (284 in Tijuana; 300 in Ciudad Juarez). All 584 participants completed the baseline interview, provided biological samples and were randomized to one of the four groups. During follow-up, 17 participants (2.9%) were lost to follow-up, of whom 10 (58.8%) had died, leaving 567 participants for analysis. This study appears to be the first intervention to attempt to simultaneously reduce injection and sexual risk behaviors among FSW-IDUs. The factorial design will permit analysis to determine whether the combination of the two interactive interventions and/or its respective components are effective in reducing injection and/or sexual risks, which will have direct, tangible policy implications for Mexico and potentially other resource-poor countries. NCT00840658.

Mujer Mas Segura (Safer Women): a combination prevention intervention to reduce sexual and injection risks among female sex workers who inject drugs

PubMed Central

2012-01-01

Background Female sex workers who inject drugs (FSW-IDUs) are at risk of acquiring HIV, sexually transmitted infections (STI) and blood-borne infections through unprotected sex and sharing injection equipment. We conducted a 2×2 factorial randomized controlled trial to evaluate combination interventions to simultaneously reduce sexual and injection risks among FSW-IDUs in Tijuana and Ciudad Juarez, Mexico. Methods/design FSW-IDUs ≥18 years reporting sharing injection equipment and unprotected sex with clients within the last month were randomized to one of four conditions based on an a priori randomization schedule, blinding interviewer/counselors to assignment. Due to the extreme vulnerability of this population, we did not include a control group that would deny some women access to preventive information. All women received similar information regardless of group allocation; the difference was in the way the information was delivered and the extent to which women had an interactive role. Each condition was a single 60-minute session, including either an interactive or didactic version of an injection risk intervention and sexual risk intervention. Women underwent interviewer-administered surveys and testing for HIV, syphilis, gonorrhea, Chlamydia, and Trichomonas at baseline and quarterly for 12 months. Combined HIV/STI incidence will be the primary outcome. Secondary outcomes are proportionate reductions in sharing of injection equipment and unprotected sex with clients. Discussion Of 1,132 women, 548 (48.4%) were excluded (88.9% were ineligible; 11.1% refused to participate or did not return); 584 eligible women enrolled (284 in Tijuana; 300 in Ciudad Juarez). All 584 participants completed the baseline interview, provided biological samples and were randomized to one of the four groups. During follow-up, 17 participants (2.9%) were lost to follow-up, of whom 10 (58.8%) had died, leaving 567 participants for analysis. This study appears to be the first intervention to attempt to simultaneously reduce injection and sexual risk behaviors among FSW-IDUs. The factorial design will permit analysis to determine whether the combination of the two interactive interventions and/or its respective components are effective in reducing injection and/or sexual risks, which will have direct, tangible policy implications for Mexico and potentially other resource-poor countries. Trial registration NCT00840658 PMID:22891807

Improved injection needles facilitate germline transformation of the buckeye butterfly Junonia coenia.

PubMed

Beaudette, Kahlia; Hughes, Tia M; Marcus, Jeffrey M

2014-01-01

Germline transformation with transposon vectors is an important tool for insect genetics, but progress in developing transformation protocols for butterflies has been limited by high post-injection ova mortality. Here we present an improved glass injection needle design for injecting butterfly ova that increases survival in three Nymphalid butterfly species. Using the needles to genetically transform the common buckeye butterfly Junonia coenia, the hatch rate for injected Junonia ova was 21.7%, the transformation rate was 3%, and the overall experimental efficiency was 0.327%, a substantial improvement over previous results in other butterfly species. Improved needle design and a higher efficiency of transformation should permit the deployment of transposon-based genetic tools in a broad range of less fecund lepidopteran species.

Intramuscular glucocorticoid injection versus placebo injection in hip osteoarthritis: a 12-week blinded randomised controlled trial.

PubMed

Dorleijn, Desirée M J; Luijsterburg, Pim A J; Reijman, Max; Kloppenburg, Margreet; Verhaar, Jan A N; Bindels, Patrick J E; Bos, Pieter Koen; Bierma-Zeinstra, Sita M A

2018-06-01

Guidelines recommend intra-articular glucocorticoid injection in patients with painful hip osteoarthritis. However, intra-articular hip injection is an invasive procedure. The efficacy of systemic glucocorticoid treatment for pain reduction in hip osteoarthritis is unknown. This randomised, double-blind, trial assessed effectiveness in hip pain reduction of an intramuscular glucocorticoid injection compared with a placebo injection in patients with hip osteoarthritis. Patients with painful hip osteoarthritis were randomised to either 40 mg triamcinolone acetate or placebo with an intramuscular injection into the gluteus muscle. The primary outcomes were severity of hip pain at rest, during walking (0-10) and WOMAC pain at 2-week postinjection. We used linear mixed models for repeated measurements at 2, 4, 6 and 12 weeks for the intention-to-treat data analysis. Of the 107 patients randomised, 106 could be analysed (52 in the glucocorticoid group, 54 in the placebo group). At 2-week follow-up, compared with placebo injection, the intramuscular glucocorticoid injection showed a significant and clinically relevant difference in hip pain reduction at rest (difference -1.3, 95% CI -2.3 to -0.3). This effect persisted for the entire 12-week follow-up. For hip pain during walking, the effect was present at 4-week, 6-week and 12-week follow-ups, and for WOMAC pain the effect was present at 6-week and 12-week follow-up. An intramuscular glucocorticoid injection showed effectiveness in patients with hip osteoarthritis on one of the three primary outcomes at 2-week postinjection. All primary outcomes showed effectiveness from 4 to 6 weeks, up to a 12-week follow-up. NTR2966. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Fluid sampling apparatus and method

DOEpatents

Yeamans, D.R.

1998-02-03

Incorporation of a bellows in a sampling syringe eliminates ingress of contaminants, permits replication of amounts and compression of multiple sample injections, and enables remote sampling for off-site analysis. 3 figs.

Constraints on geothermal reservoir volume change calculations from InSAR surface displacements and injection and production data

NASA Astrophysics Data System (ADS)

Kaven, J. Ole; Barbour, Andrew J.; Ali, Tabrez

2017-04-01

Continual production of geothermal energy at times leads to significant surface displacement that can be observed in high spatial resolution using InSAR imagery. The surface displacement can be analyzed to resolve volume change within the reservoir revealing the often-complicated patterns of reservoir deformation. Simple point source models of reservoir deformation in a homogeneous elastic or poro-elastic medium can be superimposed to provide spatially varying, kinematic representations of reservoir deformation. In many cases, injection and production data are known in insufficient detail; but, when these are available, the same Green functions can be used to constrain the reservoir deformation. Here we outline how the injection and production data can be used to constrain bounds on the solution by posing the inversion as a quadratic programming with inequality constraints and regularization rather than a conventional least squares solution with regularization. We apply this method to InSAR-derived surface displacements at the Coso and Salton Sea Geothermal Fields in California, using publically available injection and production data. At both geothermal fields the available surface deformation in conjunction with the injection and production data permit robust solutions for the spatially varying reservoir deformation. The reservoir deformation pattern resulting from the constrained quadratic programming solution is more heterogeneous when compared to a conventional least squares solution. The increased heterogeneity is consistent with the known structural controls on heat and fluid transport in each geothermal reservoir.

A novel method for intraoral access to the superior head of the human lateral pterygoid muscle.

PubMed

Oliveira, Aleli Tôrres; Camilo, Anderson Aparecido; Bahia, Paulo Roberto Valle; Carvalho, Antonio Carlos Pires; DosSantos, Marcos Fabio; da Silva, Jorge Vicente Lopes; Monteiro, André Antonio

2014-01-01

The uncoordinated activity of the superior and inferior parts of the lateral pterygoid muscle (LPM) has been suggested to be one of the causes of temporomandibular joint (TMJ) disc displacement. A therapy for this muscle disorder is the injection of botulinum toxin (BTX), of the LPM. However, there is a potential risk of side effects with the injection guide methods currently available. In addition, they do not permit appropriate differentiation between the two bellies of the muscle. Herein, a novel method is presented to provide intraoral access to the superior head of the human LPM with maximal control and minimal hazards. Computational tomography along with digital imaging software programs and rapid prototyping techniques were used to create a rapid prototyped guide to orient BTX injections in the superior LPM. The method proved to be feasible and reliable. Furthermore, when tested in one volunteer it allowed precise access to the upper head of LPM, without producing side effects. The prototyped guide presented in this paper is a novel tool that provides intraoral access to the superior head of the LPM. Further studies will be necessary to test the efficacy and validate this method in a larger cohort of subjects.

Flow Range of Centrifugal Compressor Being Extended

NASA Technical Reports Server (NTRS)

Skoch, Gary J.

2001-01-01

General Aviation will benefit from turbine engines that are both fuel-efficient and reliable. Current engines fall short of their potential to achieve these attributes. The reason is compressor surge, which is a flow stability problem that develops when the compressor is subjected to conditions that are outside of its operating range. Compressor surge can occur when fuel flow to the engine is increased, temporarily back pressuring the compressor and pushing it past its stability limit, or when the compressor is subjected to inlet flow-field distortions that may occur during takeoff and landing. Compressor surge can result in the loss of an aircraft. As a result, engine designers include a margin of safety between the operating line of the engine and the stability limit line of the compressor. Unfortunately, the most efficient operating line for the compressor is usually closer to its stability limit line than it is to the line that provides an adequate margin of safety. A wider stable flow range will permit operation along the most efficient operating line of the compressor, improving the specific fuel consumption of the engine and reducing emissions. The NASA Glenn Research Center is working to extend the stable flow range of the compressor. Significant extension has been achieved in axial compressors by injecting air upstream of the compressor blade rows. Recently, the technique was successfully applied to a 4:1 pressure ratio centrifugal compressor by injecting streams of air into the diffuser. Both steady and controlled unsteady injection were used to inject air through the diffuser shroud surface and extend the range. Future work will evaluate the effect of air injection through the diffuser hub surface and diffuser vanes with the goal of maximizing the range extension while minimizing the amount of injected air that is required.

Attitudes toward medication-assisted treatment among fishermen in Kuantan, Malaysia, who inject drugs.

PubMed

Brown, Shan-Estelle; Wickersham, Jeffrey A; Pelletier, Alyssa R; Marcus, Ruthanne M; Erenrich, Rebecca; Kamarulzaman, Adeeba; Altice, Frederick L

2017-01-01

Fishermen who inject drugs represent an understudied group at high risk for HIV in Malaysia. This study describes fishing, drug use, and attitudes toward medication-assisted treatment (MAT) for opioid use disorders. Thirty-four male ethnic Malay fishermen completed semistructured interviews analyzed by content analysis. Analysis revealed four themes surrounding opioids, which they called ubat ("medicine"): (a) the fishing lifestyle facilitating substance use, (b) previous unsuccessful attempts to quit, (c) categorizing substances as haram or halal, and (d) attitudes toward MAT. Fishermen's environment permits substance use, including injecting drugs on boats. Fishermen expressed more positive attitudes toward methadone and negative attitudes toward buprenorphine.

Intra-Arterial Delivery of AAV Vectors to the Mouse Brain After Mannitol Mediated Blood Brain Barrier Disruption

PubMed Central

Santillan, Alejandro; Sondhi, Dolan; Dyke, Jonathan P.; Crystal, Ronald G.; Gobin, Y. Pierre; Ballon, Douglas J.

2014-01-01

The delivery of therapeutics to neural tissue is greatly hindered by the blood brain barrier (BBB). Direct local delivery via diffusive release from degradable implants or direct intra-cerebral injection can bypass the BBB and obtain high concentrations of the therapeutic in the targeted tissue, however the total volume of tissue that can be treated using these techniques is limited. One treatment modality that can potentially access large volumes of neural tissue in a single treatment is intra-arterial (IA) injection after osmotic blood brain barrier disruption. In this technique, the therapeutic of interest is injected directly into the arteries that feed the target tissue after the blood brain barrier has been disrupted by exposure to a hyperosmolar mannitol solution, permitting the transluminal transport of the therapy. In this work we used contrast enhanced magnetic resonance imaging (MRI) studies of IA injections in mice to establish parameters that allow for extensive and reproducible BBB disruption. We found that the volume but not the flow rate of the mannitol injection has a significant effect on the degree of disruption. To determine whether the degree of disruption we observed with this method was sufficient for delivery of nanoscale therapeutics, we performed IA injections of an adeno-associated viral vector containing the CLN2 gene (AAVrh.10CLN2), which is mutated in the lysosomal storage disorder Late Infantile Neuronal Ceroid Lipofuscinosis (LINCL). We demonstrated that IA injection of AAVrh.10CLN2 after BBB disruption can achieve widespread transgene production in the mouse brain after a single administration. Further, we showed that there exists a minimum threshold of BBB disruption necessary to permit the AAV.rh10 vector to pass into the brain parenchyma from the vascular system. These results suggest that IA administration may be used to obtain widespread delivery of nanoscale therapeutics throughout the murine brain after a single administration. PMID:25270115

A Novel Method for Intraoral Access to the Superior Head of the Human Lateral Pterygoid Muscle

PubMed Central

Oliveira, Aleli Tôrres; Camilo, Anderson Aparecido; Bahia, Paulo Roberto Valle; Carvalho, Antonio Carlos Pires; DosSantos, Marcos Fabio; da Silva, Jorge Vicente Lopes; Monteiro, André Antonio

2014-01-01

Background. The uncoordinated activity of the superior and inferior parts of the lateral pterygoid muscle (LPM) has been suggested to be one of the causes of temporomandibular joint (TMJ) disc displacement. A therapy for this muscle disorder is the injection of botulinum toxin (BTX), of the LPM. However, there is a potential risk of side effects with the injection guide methods currently available. In addition, they do not permit appropriate differentiation between the two bellies of the muscle. Herein, a novel method is presented to provide intraoral access to the superior head of the human LPM with maximal control and minimal hazards. Methods. Computational tomography along with digital imaging software programs and rapid prototyping techniques were used to create a rapid prototyped guide to orient BTX injections in the superior LPM. Results. The method proved to be feasible and reliable. Furthermore, when tested in one volunteer it allowed precise access to the upper head of LPM, without producing side effects. Conclusions. The prototyped guide presented in this paper is a novel tool that provides intraoral access to the superior head of the LPM. Further studies will be necessary to test the efficacy and validate this method in a larger cohort of subjects. PMID:24963484

Thermal acidization and recovery process for recovering viscous petroleum

DOEpatents

Poston, Robert S.

1984-01-01

A thermal acidization and recovery process for increasing production of heavy viscous petroleum crude oil and synthetic fuels from subterranean hydrocarbon formations containing clay particles creating adverse permeability effects is described. The method comprises injecting a thermal vapor stream through a well bore penetrating such formations to clean the formation face of hydrocarbonaceous materials which restrict the flow of fluids into the petroleum-bearing formation. Vaporized hydrogen chloride is then injected simultaneously to react with calcium and magnesium salts in the formation surrounding the bore hole to form water soluble chloride salts. Vaporized hydrogen fluoride is then injected simultaneously with its thermal vapor to dissolve water-sensitive clay particles thus increasing permeability. Thereafter, the thermal vapors are injected until the formation is sufficiently heated to permit increased recovery rates of the petroleum.

In-situ generation of oxygen-releasing metal peroxides

DOEpatents

Looney, Brian B.; Denham, Miles E.

2007-01-09

A method for remediation of contaminants in soil and groundwater is disclosed. The method generates oxygen releasing solids in groundwater or soil by injecting an aqueous energetic oxidant solution containing free radicals, oxidative conditions can be created within or ahead of a contaminant plume. Some contaminants may be remediated directly by reaction with the free radicals. Additionally and more importantly, the free radicals create an oxidative condition whereby native or injected materials, especially metals, are converted to peroxides. These peroxides provide a long-term oxygen reservoir, releasing oxygen relatively slowly over time. The oxygen can enhance microbial metabolism to remediate contaminants, can react with contaminant metals either to form immobile precipitants or to mobilize other metals to permit remediation through leaching techniques. Various injection strategies for injecting the energetic oxidant solution are also disclosed.

40 CFR 145.23 - Program description.

Code of Federal Regulations, 2013 CFR

2013-07-01

... and any State administrative or judicial review procedures. (d) Copies of the permit form(s... reviewing the wells for compliance with applicable monitoring, reporting, construction, and financial... for Class II enhanced oil recovery or enhanced gas recovery wells transitioning to Class VI injection...

40 CFR 145.23 - Program description.

Code of Federal Regulations, 2012 CFR

2012-07-01

... and any State administrative or judicial review procedures. (d) Copies of the permit form(s... reviewing the wells for compliance with applicable monitoring, reporting, construction, and financial... for Class II enhanced oil recovery or enhanced gas recovery wells transitioning to Class VI injection...

40 CFR 145.23 - Program description.

Code of Federal Regulations, 2014 CFR

2014-07-01

... and any State administrative or judicial review procedures. (d) Copies of the permit form(s... reviewing the wells for compliance with applicable monitoring, reporting, construction, and financial... for Class II enhanced oil recovery or enhanced gas recovery wells transitioning to Class VI injection...

40 CFR 145.23 - Program description.

Code of Federal Regulations, 2011 CFR

2011-07-01

... and any State administrative or judicial review procedures. (d) Copies of the permit form(s... reviewing the wells for compliance with applicable monitoring, reporting, construction, and financial... for Class II enhanced oil recovery or enhanced gas recovery wells transitioning to Class VI injection...

77 FR 59926 - Agency Information Collection Activities; Proposed Collection; Comment Request; Guidance...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-01

... by the Project BioShield Act of 2004 (Pub. L. 108-276). The FD&C Act permits the Commissioner of Food... variability based on whether there is an active manufacturer respondent, other factors also inject significant...

What happened to the HIV epidemic among non-injecting drug users in New York City?

PubMed

Des Jarlais, Don C; Arasteh, Kamyar; McKnight, Courtney; Feelemyer, Jonathan; Campbell, Aimee N C; Tross, Susan; Cooper, Hannah L F; Hagan, Holly; Perlman, David C

2017-02-01

HIV has reached high prevalence in many non-injecting drug user (NIDU) populations. The aims of this study were to (1) examine the trend in HIV prevalence among non-injecting cocaine and heroin NIDUs in New York City, (2) identify factors potentially associated with the trend and (3) estimate HIV incidence among NIDUs. Serial-cross sectional surveys of people entering drug treatment programs. People were permitted to participate only once per year, but could participate in multiple years. Mount Sinai Beth Israel drug treatment programs in New York City, USA. We recruited 3298 non-injecting cocaine and heroin users from 2005 to 2014. Participants were 78.7% male, 6.1% white, 25.7% Hispanic and 65.8% African American. Smoking crack cocaine was the most common non-injecting drug practice. Trend tests were used to examine HIV prevalence, demographics, drug use, sexual behavior and use of antiretroviral treatment (ART) by calendar year; χ 2 and multivariable logistic regression were used to compare 2005-10 versus 2011-14. HIV prevalence declined approximately 1% per year (P < 0.001), with a decline from 16% in 2005-10 to 8% in 2011-14 (P < 0.001). The percentages of participants smoking crack and having multiple sexual partners declined and the percentage of HIV-positive people on ART increased. HIV incidence among repeat participants was 1.2 per 1000 person-years (95% confidence interval = 0.03/1000-7/1000). HIV prevalence has declined and a high percentage of HIV-positive non-injecting drug users (NIDUs) are receiving antiretroviral treatment, suggesting an end to the HIV epidemic among NIDUs in New York City. These results can be considered a proof of concept that it is possible to control non-injecting drug use related sexual transmission HIV epidemics. © 2016 Society for the Study of Addiction.

Attitudes toward medication-assisted treatment among fishermen in Kuantan, Malaysia, who inject drugs

PubMed Central

Brown, Shan-Estelle; Wickersham, Jeffrey A.; Pelletier, Alyssa R.; Marcus, Ruthanne M.; Erenrich, Rebecca; Kamarulzaman, Adeeba; Altice, Frederick L.

2017-01-01

Fishermen who inject drugs represent an understudied group at high risk for HIV in Malaysia. This study describes fishing, drug use, and attitudes toward medication-assisted treatment (MAT) for opioid use disorders. Thirty-four male ethnic Malay fishermen completed semistructured interviews analyzed by content analysis. Analysis revealed four themes surrounding opioids, which they called ubat (“medicine”): (a) the fishing lifestyle facilitating substance use, (b) previous unsuccessful attempts to quit, (c) categorizing substances as haram or halal, and (d) attitudes toward MAT. Fishermen’s environment permits substance use, including injecting drugs on boats. Fishermen expressed more positive attitudes toward methadone and negative attitudes toward buprenorphine. PMID:27404914

40 CFR 144.33 - Area permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... characteristics; (2) Within the same well field, facility site, reservoir, project, or similar unit in the same...) The requirements for construction, monitoring, reporting, operation, and abandonment, for all wells...; and (3) The cumulative effects of drilling and operation of additional injection wells are considered...

Influence of pre-injection control parameters on main-injection fuel quantity for an electronically controlled double-valve fuel injection system of diesel engine

NASA Astrophysics Data System (ADS)

Song, Enzhe; Fan, Liyun; Chen, Chao; Dong, Quan; Ma, Xiuzhen; Bai, Yun

2013-09-01

A simulation model of an electronically controlled two solenoid valve fuel injection system for a diesel engine is established in the AMESim environment. The accuracy of the model is validated through comparison with experimental data. The influence of pre-injection control parameters on main-injection quantity under different control modes is analyzed. In the spill control valve mode, main-injection fuel quantity decreases gradually and then reaches a stable level because of the increase in multi-injection dwell time. In the needle control valve mode, main-injection fuel quantity increases with rising multi-injection dwell time; this effect becomes more obvious at high-speed revolutions and large main-injection pulse widths. Pre-injection pulse width has no obvious influence on main-injection quantity under the two control modes; the variation in main-injection quantity is in the range of 1 mm3.

MRI evidence of endolymphatic impermeability to the gadolinium molecule in the in vivo mouse inner ear at 9.4 tesla.

PubMed

Counter, S Allen; Nikkhou, Sahar; Brené, Stefan; Damberg, Peter; Sierakowiak, Adam; Klason, Tomas; Berglin, Cecilia Engmér; Laurell, Göran

2013-01-01

Previous in vivo experimental magnetic resonance imaging (MRI) investigations of the mammalian inner ear at 4.7 Tesla have indicated that intravenously injected gadolinium (Gd) penetrates the perilymphatic labyrinth, but not the endolymphatic membranous labyrinth. In the present study, high field MRI at 9.4T was used to visualize the in vivo mouse vestibulo-cochlea system, and to determine whether the endolymphatic system is permeable to a Gd complex. A 9.4 T Varian magnet equipped with a 12 cm inner diameter gradient system with maximum gradient strength of 600 mT/m, a millipede coil (Varian design) and a Gd contrast agent were used for image acquisition in the normal C57 BL-6 mouse. High-resolution 2D and 3D images of the mouse cochlea were acquired within 80 minutes following intravenous injection of Gd. Gd initially permeated the perilymphatic scala tympani and scala vestibuli, and permitted visualization of both cochlear turns from base to apex. The superior, inferior and lateral semicircular canals were subsequently visualized in 3 planes. The membranous endolymphatic labyrinth was impermeable to intravenously injected Gd, and thus showed no apparent uptake of Gd at 9.4T. The 9.4T field strength MRI permitted acquisition of high resolution images of anatomical and physiological features of the normal, wild type mouse perilymphatic inner ear in vivo, and provided further evidence that the endolymphatic system is impermeable to intravenously injected Gd.

21 CFR 1312.22 - Application for export permit.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Application for export permit. 1312.22 Section... EXPORTATION OF CONTROLLED SUBSTANCES Exportation of Controlled Substances § 1312.22 Application for export permit. (a) An application for a permit to export controlled substances shall be made on DEA Form 161...

Clinical trial of combined radio- and fluorescence-guided sentinel lymph node biopsy in breast cancer

PubMed Central

Schaafsma, Boudewijn E.; Verbeek, Floris P.R.; Rietbergen, Daphne D.D.; van der Hiel, Bernies; van der Vorst, Joost R.; Liefers, Gerrit-Jan; Frangioni, John V.; van de Velde, Cornelis J.H.; van Leeuwen, Fijs W.B.; Vahrmeijer, Alexander L.

2013-01-01

Background Combining radioactive colloids and a near-infrared (NIR) fluorophore permit preoperative planning and intraoperative localization of deeply located sentinel lymph nodes (SLNs) with direct optical guidance by a single lymphatic tracer. The aim of this clinical trial was to evaluate and optimize a hybrid NIR fluorescence and radioactive tracer for SLN detection in breast cancer patients. Method Patients with breast cancer undergoing SLN biopsy were enrolled. The day before surgery, indocyanine green (ICG)-99mTc-Nanocolloid was injected periareolarly and a lymphoscintigram was acquired. Directly before surgery, blue dye was injected. Intraoperative SLN localization was performed by a gamma probe and the Mini-FLARETM NIR fluorescence imaging system. Patients were divided into two dose groups, with one group receiving twice the particle density of ICG and nanocolloid, but the same dose of radioactive 99mTechnetium. Results Thirty-two patients were enrolled in the trial. At least one SLN was identified pre- and intraoperatively. All 48 axillary SLNs could be detected by gamma tracing and NIR fluorescence imaging, but only 42 of them stained blue. NIR fluorescence permitted detection of lymphatic vessels draining to the SLN up to 29 hours after injection. Increasing the particle density by two-fold did not yield a difference in fluorescence intensity, median 255 (range 98 – 542) vs. median 284 (90 – 921; P = 0.590), or signal- to- background ratio, median 5.4 (range 3.0 – 15.4) vs. median 4.9 (3.5 – 16.3; P = 1.000), of the SLN. Conclusion The hybrid NIR fluorescence and radioactive tracer ICG-99mTc-Nanocolloid permitted accurate pre- and intraoperative detection of the SLNs in patients with breast cancer. PMID:23696463

Computational study of single-expansion-ramp nozzles with external burning

NASA Astrophysics Data System (ADS)

Yungster, Shaye; Trefny, Charles J.

1992-04-01

A computational investigation of the effects of external burning on the performance of single expansion ramp nozzles (SERN) operating at transonic speeds is presented. The study focuses on the effects of external heat addition and introduces a simplified injection and mixing model based on a control volume analysis. This simplified model permits parametric and scaling studies that would have been impossible to conduct with a detailed CFD analysis. The CFD model is validated by comparing the computed pressure distribution and thrust forces, for several nozzle configurations, with experimental data. Specific impulse calculations are also presented which indicate that external burning performance can be superior to other methods of thrust augmentation at transonic speeds. The effects of injection fuel pressure and nozzle pressure ratio on the performance of SERN nozzles with external burning are described. The results show trends similar to those reported in the experimental study, and provide additional information that complements the experimental data, improving our understanding of external burning flowfields. A study of the effect of scale is also presented. The results indicate that combustion kinetics do not make the flowfield sensitive to scale.

Computational study of single-expansion-ramp nozzles with external burning

NASA Technical Reports Server (NTRS)

Yungster, Shaye; Trefny, Charles J.

1992-01-01

A computational investigation of the effects of external burning on the performance of single expansion ramp nozzles (SERN) operating at transonic speeds is presented. The study focuses on the effects of external heat addition and introduces a simplified injection and mixing model based on a control volume analysis. This simplified model permits parametric and scaling studies that would have been impossible to conduct with a detailed CFD analysis. The CFD model is validated by comparing the computed pressure distribution and thrust forces, for several nozzle configurations, with experimental data. Specific impulse calculations are also presented which indicate that external burning performance can be superior to other methods of thrust augmentation at transonic speeds. The effects of injection fuel pressure and nozzle pressure ratio on the performance of SERN nozzles with external burning are described. The results show trends similar to those reported in the experimental study, and provide additional information that complements the experimental data, improving our understanding of external burning flowfields. A study of the effect of scale is also presented. The results indicate that combustion kinetics do not make the flowfield sensitive to scale.

Response to a Letter Regarding the Use Of Urea Injection In Place of Ammonia Injection

EPA Pesticide Factsheets

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Ion-implanted epitaxially grown ZnSe

NASA Technical Reports Server (NTRS)

Chernow, F.

1975-01-01

The use of ZnSe to obtain efficient, short wavelength injection luminescence was investigated. It was proposed that shorter wavelength emission and higher efficiency be achieved by employing a p-i-n diode structure rather than the normal p-n diode structure. The intervening i layer minimizes concentration quenching effects and the donor-acceptor pair states leading to long wavelength emission. The surface p layer was formed by ion implantation; implantation of the i layer rather than the n substrate permits higher, uncompensated p-type doping. An ion implanted p-n junction in ZnSe is efficiency-limited by high electron injection terminating in nonradiative recombination at the front surface, and by low hole injection resulting from the inability to obtain high conductivity p-type surface layers. While the injection ratio in p-n junctions was determined by the radio of majority carrier concentrations, the injection ratio in p-i-n structures was determined by the mobility ratios and/or space charge neutrality requirements in the i layer.

Analysis for predicting adiabatic wall temperatures with single hole coolant injection into a low speed crossflow

NASA Astrophysics Data System (ADS)

Wang, C. R.; Papell, S. S.; Graham, R. W.

Assuming the local adiabatic wall temperature equals the local total temperature in a low speed coolant mixing layer, integral conservation equations with and without the boundary layer effects are formulated for the mixing layer downstream of a single coolant injection hole oriented at a 30 degree angle to the crossflow. These equations are solved numerically to determine the center line local adiabatic wall temperature and the effective coolant coverage area. Comparison of the numerical results with an existing film cooling experiment indicates that the present analysis permits a simplified but reasonably accurate prediction of the centerline effectiveness and coolant coverage area downstream of a single hole crossflow streamwise injection at 30 degree inclination angle.

Analysis for predicting adiabatic wall temperatures with single hole coolant injection into a low speed crossflow

NASA Technical Reports Server (NTRS)

Wang, C. R.; Papell, S. S.; Graham, R. W.

1981-01-01

Assuming the local adiabatic wall temperature equals the local total temperature in a low speed coolant mixing layer, integral conservation equations with and without the boundary layer effects are formulated for the mixing layer downstream of a single coolant injection hole oriented at a 30 degree angle to the crossflow. These equations are solved numerically to determine the center line local adiabatic wall temperature and the effective coolant coverage area. Comparison of the numerical results with an existing film cooling experiment indicates that the present analysis permits a simplified but reasonably accurate prediction of the centerline effectiveness and coolant coverage area downstream of a single hole crossflow streamwise injection at 30 degree inclination angle.

Analysis for predicting adiabatic wall temperatures with single hole coolant injection into a low speed crossflow

NASA Astrophysics Data System (ADS)

Wang, C. R.; Papell, S. S.; Graham, R. W.

1981-03-01

Assuming the local adiabatic wall temperature equals the local total temperature in a low speed coolant mixing layer, integral conservation equations with and without the boundary layer effects are formulated for the mixing layer downstream of a single coolant injection hole oriented at a 30 degree angle to the crossflow. These equations are solved numerically to determine the center-line local adiabatic wall temperature and the effective coolant coverage area. Comparison of the numerical results with an existing film cooling experiment indicates that the present analysis permits a simplified but reasonably accurate prediction of the centerline effectiveness and coolant coverage area downstream of a single hole crossflow streamwise injection at 30-deg inclination angle.

Analysis for predicting adiabatic wall temperatures with single hole coolant injection into a low speed crossflow

NASA Technical Reports Server (NTRS)

Wang, C. R.; Papell, S. S.; Graham, R. W.

1981-01-01

Assuming the local adiabatic wall temperature equals the local total temperature in a low speed coolant mixing layer, integral conservation equations with and without the boundary layer effects are formulated for the mixing layer downstream of a single coolant injection hole oriented at a 30 degree angle to the crossflow. These equations are solved numerically to determine the center-line local adiabatic wall temperature and the effective coolant coverage area. Comparison of the numerical results with an existing film cooling experiment indicates that the present analysis permits a simplified but reasonably accurate prediction of the centerline effectiveness and coolant coverage area downstream of a single hole crossflow streamwise injection at 30-deg inclination angle.

Chemical meningitis related to intra-CSF liposomal cytarabine.

PubMed

Durand, Bénédicte; Zairi, Fahed; Boulanger, Thomas; Bonneterre, Jacques; Mortier, Laurent; Le Rhun, Emilie

2017-10-01

Therapeutic options of leptomeningeal metastases include intra-cerebrospinal fluid (CSF) chemotherapy. Among intra-CSF agents, liposomal cytarabine has advantages but can induce specific toxicities. A BRAF-V600E-mutated melanoma leptomeningeal metastases patient, treated by dabrafenib and liposomal cytarabine, presented after the first injection of liposomal cytarabine with hyperthermia and headaches. Despite sterile CSF/blood analyses, extended intravenous antibiotics were given and the second injection was delayed. The diagnosis of chemical meningitis was finally made. Dose reduction and appropriate symptomatic treatment permitted the administration of 15 injections of liposomal cytarabine combined with dabrafenib. A confirmation of the diagnosis of chemical meningitis is essential in order (1) not to delay intra-CSF or systemic chemotherapy or (2) to limit the administration of unnecessary but potentially toxic antibiotics.

Injectable contraceptive sales at licensed chemical seller shops in ghana: access and reported use in rural and periurban communities.

PubMed

Lebetkin, Elena; Orr, Tracy; Dzasi, Kafui; Keyes, Emily; Shelus, Victoria; Mensah, Stephen; Nagai, Henry; Stanback, John

2014-03-01

Most women in Ghana obtain oral contraceptives and condoms from shops run by licensed chemical sellers, but such shops are not legally permitted to sell the country's most widely used method, the injectable. Allowing shops to sell the injectable could increase access to and use of the method. In 2012-2013, semistructured telephone interviews were conducted among convenience samples of 94 licensed chemical seller shop operators in two districts who were trained to sell the injectable and of 298 women who purchased the method from these shops. Follow-up interviews were conducted with 92 clients approximately three months after their initial injectable purchase. Ninety-seven percent of shop operators reported selling the injectable, and 94% felt sufficiently trained to provide family planning methods and services. Virtually all sellers (99%) referred clients to a hospital or health facility for injection; none provided injections themselves. Fifty-six percent of injectable clients were new family planning users. Of those who completed a follow-up interview, 79% had purchased the injectable again from a shop. Virtually all clients (97%) reported getting their injection at the health facility to which they were referred by the seller. Women cited trust, convenience and commodities being in stock as key reasons for purchasing from a shop. Licensed chemical seller shop operators can safely sell the injectable and refer clients to health facilities for screening, counseling and injection.

Cobinamide-Based Cyanide Analysis by Multiwavelength Spectrometry in a Liquid Core Waveguide

PubMed Central

Ma, Jian; Dasgupta, Purnendu K.; Blackledge, William; Boss, Gerry R.

2010-01-01

A novel cyanide analyzer based on sensitive cobinamide chemistry relies on simultaneous reagent and sample injection and detection in a 50 cm liquid core waveguide (LCW) flow cell illuminated by a white light emitting diode. The transmitted light is read by a fiber-optic charge coupled device (CCD) spectrometer. Alkaline cobinamide (orange, λmax = 510 nm) changes to violet (λmax = 583 nm) upon reaction with cyanide. Multiwavelength detection permits built-in correction for artifact responses intrinsic to a single-line flow injection system and corrects for drift. With optimum choice of the reaction medium, flow rate, and mixing coil length, the limit of detection (LOD, S/N = 3) is 30 nM and the linear dynamic range extends to 10 μM. The response base width for 1% carryover is <95 s, permitting a throughput of 38 samples/h. The relative standard deviations (rsd) for repetitive determinations at 0.15, 0.5, and 1 μM were 7.6% (n = 5), 3.2% (n = 7), and 1.7% (n = 6), respectively. Common ions at 250–80 000× concentrations do not interfere except for sulfide. For the determination of 2 μM CN−, the presence of 2, 5, 10, 20, 100, and 1000 μM HS− results in 22, 27, 48, 58, 88, and 154% overestimation of cyanide. The sulfide product actually has a different characteristic absorption, and in those samples where significant presence is likely, this can be corrected for. We demonstrate applicability by analyzing the hydrolytic cyanide extract of apple and pear seeds with orange seeds as control and also measure HCN in breath air samples. Spike recoveries in these sample extracts ranged from 91 to 108%. PMID:20560532

MRI Evidence of Endolymphatic Impermeability to the Gadolinium Molecule in the In Vivo Mouse Inner Ear at 9.4 Tesla

PubMed Central

Counter, S Allen; Nikkhou, Sahar; Brené, Stefan; Damberg, Peter; Sierakowiak, Adam; Klason, Tomas; Berglin, Cecilia Engmér; Laurell, Göran

2013-01-01

Objective: Previous in vivo experimental magnetic resonance imaging (MRI) investigations of the mammalian inner ear at 4.7 Tesla have indicated that intravenously injected gadolinium (Gd) penetrates the perilymphatic labyrinth, but not the endolymphatic membranous labyrinth. In the present study, high field MRI at 9.4T was used to visualize the in vivo mouse vestibulo-cochlea system, and to determine whether the endolymphatic system is permeable to a Gd complex. Methods: A 9.4 T Varian magnet equipped with a 12 cm inner diameter gradient system with maximum gradient strength of 600 mT/m, a millipede coil (Varian design) and a Gd contrast agent were used for image acquisition in the normal C57 BL-6 mouse. Results: High-resolution 2D and 3D images of the mouse cochlea were acquired within 80 minutes following intravenous injection of Gd. Gd initially permeated the perilymphatic scala tympani and scala vestibuli, and permitted visualization of both cochlear turns from base to apex. The superior, inferior and lateral semicircular canals were subsequently visualized in 3 planes. The membranous endolymphatic labyrinth was impermeable to intravenously injected Gd, and thus showed no apparent uptake of Gd at 9.4T. Conclusion: The 9.4T field strength MRI permitted acquisition of high resolution images of anatomical and physiological features of the normal, wild type mouse perilymphatic inner ear in vivo, and provided further evidence that the endolymphatic system is impermeable to intravenously injected Gd. PMID:23894262

43 CFR 3274.11 - What must I give BLM to approve my commercial use permit application?

Code of Federal Regulations, 2014 CFR

2014-10-01

... configuration, including meters; (f) A schematic flow diagram of the utilization facility, including... calibration schedule of production, injection, and royalty meters; (b) A schematic diagram of the utilization... is located off the utilization site, give us a generalized schematic diagram of the electrical...

43 CFR 3274.11 - What must I give BLM to approve my commercial use permit application?

Code of Federal Regulations, 2012 CFR

2012-10-01

... configuration, including meters; (f) A schematic flow diagram of the utilization facility, including... calibration schedule of production, injection, and royalty meters; (b) A schematic diagram of the utilization... is located off the utilization site, give us a generalized schematic diagram of the electrical...

43 CFR 3274.11 - What must I give BLM to approve my commercial use permit application?

Code of Federal Regulations, 2011 CFR

2011-10-01

... configuration, including meters; (f) A schematic flow diagram of the utilization facility, including... calibration schedule of production, injection, and royalty meters; (b) A schematic diagram of the utilization... is located off the utilization site, give us a generalized schematic diagram of the electrical...

43 CFR 3274.11 - What must I give BLM to approve my commercial use permit application?

Code of Federal Regulations, 2013 CFR

2013-10-01

... configuration, including meters; (f) A schematic flow diagram of the utilization facility, including... calibration schedule of production, injection, and royalty meters; (b) A schematic diagram of the utilization... is located off the utilization site, give us a generalized schematic diagram of the electrical...

76 FR 36917 - Clean Air Act Operating Permit Program; Petition for Objection to State Operating Permit for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-23

... business; (II) The Title V permit failed to provide for the control of mercury emissions, an air... Reasonably Available Control Technology for the control of carbon dioxide emissions or for mercury emissions...

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... being used contains the appropriate pollution control technologies (or equivalent systems/pesticide... appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit writer which... written submission to the appropriate permitting authority, e.g., the local Control Authority (the POTW...

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... being used contains the appropriate pollution control technologies (or equivalent systems/pesticide... appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit writer which... written submission to the appropriate permitting authority, e.g., the local Control Authority (the POTW...

A prospective, randomized, open-label study comparing the efficacy and safety of preprandial and prandial insulin in combination with acarbose in elderly, insulin-requiring patients with type 2 diabetes mellitus.

PubMed

Yang, Guang; Li, Chunlin; Gong, Yanping; Li, Jian; Cheng, Xiaoling; Tian, Hui

2013-06-01

By delaying absorption of carbohydrates, acarbose can reduce preprandial hyperglycemia and delay the emergence of postprandial hyperglycemia. To evaluate whether acarbose can shorten the desirable time interval between insulin injection and meals, 60 elderly (≥60 years) patients with unsatisfactorily controlled type 2 diabetes mellitus despite insulin use were enrolled in a randomized, open-label study of 16 weeks' duration. Two groups (n=20 each) were randomized to receive isophane protamine biosynthetic human insulin 70/30 injections twice daily 30 min before meals plus acarbose 50 mg once daily (Group A) or three times daily (Group B) before meals, whereas the third group (n=20) received isophane protamine biosynthetic human insulin 70/30 injections twice daily immediately before meals plus acarbose 50 mg three times daily before meals (Group C). The required insulin dosage at study end was significantly less in Groups B and C than in Group A. Both continuous glucose monitoring data and the patients' self-monitoring data indicated that blood glucose variability parameters were significantly improved in Groups B and C in comparison with Group A, but there were no significant differences between Groups B and C. The incidence of hypoglycemia was low in all three groups. The absence of a significant difference in glucose variability between Groups B and C suggests that the addition of acarbose permitted adjustment of the insulin administration time from 30 min before meals to immediately before meals-which may be more convenient for patients-without affecting glycemic control.

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... system being used contains the appropriate pollution control technologies (or equivalent systems... the appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit... Control Authority (the POTW) or NPDES permit writer, which states that the P2 Alternative is being...

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... system being used contains the appropriate pollution control technologies (or equivalent systems... the appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit... Control Authority (the POTW) or NPDES permit writer, which states that the P2 Alternative is being...

40 CFR 455.41 - Special definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... system being used contains the appropriate pollution control technologies (or equivalent systems... the appropriate permitting authority, e.g., the local Control Authority (the POTW) or NPDES permit... Control Authority (the POTW) or NPDES permit writer, which states that the P2 Alternative is being...

Incidence of inadvertent intra-articular lumbar facet joint injection during fluoroscopically guided interlaminar epidural steroid injection.

PubMed

Huang, Ambrose J; Palmer, William E

2012-02-01

To determine the incidence of inadvertent lumbar facet joint injection during an interlaminar epidural steroid injection (ESI). A total of 686 interlaminar lumbar ESIs were performed from January 1, 2009 to December 31, 2009. Archived images from these cases were retrospectively reviewed on the PACS. Positive cases of inadvertent lumbar facet joint injection were identified by the characteristic sigmoid-shaped contrast pattern projecting over the posterior elements on the lateral view and/or ovoid contrast projecting over the facet joints on the anteroposterior (AP) view. Eight positive events were identified (1.2%). There was no statistically significant gender or lumbar level predilection. In 3/8 of the positive cases (37.5%), the inadvertent facet joint injection was recognized by the operator. The needle was repositioned as a result, and contrast within the posterior epidural space was documented by the end of the procedure. In 5/8 of the positive cases (62.5%), the patients reported an immediate decrease in the presenting pain. The incidence of inadvertent lumbar facet joint injection during an interlaminar epidural steroid injection is low. Recognizing the imaging features of this event permits the operator to redirect the needle tip into the epidural space and/or identify the facet joint(s) as a source of the patient's presenting pain.

[Value of injection hepato-lymphography during percutaneous transhepatic cholangiography in patients with cholestasis].

PubMed

Sharipov, V Sh

2000-01-01

Injection hepatography (IH) was made in 278 patients with cholestasis to study the drainage function of the liver. In 208 cases. IH was performed as a test during percutaneous transhepatic cholangiography (PTHC). The hepatic lymph pathways were imaged in 167 (60%) patients. Images of the biliary tract were obtained in 245 (88.1%) patients with cholestasis, it being not dilated in 34 (12.2%) patients. The fact that hepatolymphography may be performed during PTHC as an independent test permits verification of hepatic lymph circulatory disorders that are an index of the rate of inflammation in the organ.

Optimal contant time injection policy for enhanced oil recovery and characterization of optimal viscous profiles

NASA Astrophysics Data System (ADS)

Daripa, Prabir

2011-11-01

We numerically investigate the optimal viscous profile in constant time injection policy of enhanced oil recovery. In particular, we investigate the effect of a combination of interfacial and layer instabilities in three-layer porous media flow on the overall growth of instabilities and thereby characterize the optimal viscous profile. Results based on monotonic and non-monotonic viscous profiles will be presented. Time permitting. we will also present results on multi-layer porous media flows for Newtonian and non-Newtonian fluids and compare the results. The support of Qatar National Fund under a QNRF Grant is acknowledged.

Active CO2 Reservoir Management for Carbon Capture, Utilization, and Sequestration: Impact on Permitting, Monitoring, and Public Acceptance

NASA Astrophysics Data System (ADS)

Buscheck, T. A.; Chen, M.; Sun, Y.; Hao, Y.; Court, B.; Celia, M. A.; Wolery, T.; Aines, R. D.

2011-12-01

CO2 capture and sequestration (CCS) integrated with geothermal energy production in deep geological formations can play an important role in reducing CO2 emissions to the atmosphere and thereby mitigate global climate change. For industrial-scale CO2 injection in saline formations, pressure buildup can limit storage capacity and security. Active CO2 Reservoir Management (ACRM) combines brine production with CO2 injection to relieve pressure buildup, increase injectivity, manipulate CO2 migration, constrain brine leakage, and enable beneficial utilization of produced brine. Therefore, ACRM can be an enabler of carbon capture, utilization, and sequestration (CCUS). Useful products may include freshwater, cooling water, make-up water for pressure support in oil, gas, and geothermal reservoir operations, and geothermal energy production. Implementation barriers to industrial-scale CCS include concerns about (1) CO2 sequestration security and assurance, (2) pore-space competition with neighboring subsurface activities, (3) CO2 capture costs, and (4) water-use demands imposed by CCS operations, which is particularly important where water resources are already scarce. CCUS, enabled by ACRM, has the potential of addressing these barriers. Pressure relief from brine production can substantially reduce the driving force for potential CO2 and brine migration, as well as minimize interference with neighboring subsurface activities. Electricity generated from geothermal energy can offset a portion of the parasitic energy and financial costs of CCS. Produced brine can be used to generate freshwater by desalination technologies, such as RO, provide a source for saltwater cooling systems or be used as make-up water for oil, gas, or geothermal reservoir operations, reducing the consumption of valuable freshwater resources. We examine the impact of brine production on reducing CO2 and brine leakage. A volumetric balance between injected and produced fluids minimizes the spatial extent of the pressure perturbation, substantially reducing both the Area of Review (AoR) and interactions with neighboring subsurface activities. This will reduce pore-space competition between neighboring subsurface activities, allowing for independent planning, assessment, and permitting. Because post-injection pressure buildup is virtually eliminated, this could have a major impact on post-injection monitoring requirements. Reducing the volume of rock over which brine can migrate may significantly affect site characterization requirements, as well as the impact of parametric and conceptual model uncertainties, such as those related to abandoned wells. ACRM-CCUS has the potential of playing a beneficial role in site-characterization, permitting, and monitoring activities, and in gaining public acceptance. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Continuous flow, explosives vapor generator and sensor chamber.

PubMed

Collins, Greg E; Giordano, Braden C; Sivaprakasam, Vasanthi; Ananth, Ramagopal; Hammond, Mark; Merritt, Charles D; Tucker, John E; Malito, Michael; Eversole, Jay D; Rose-Pehrsson, Susan

2014-05-01

A novel liquid injection vapor generator (LIVG) is demonstrated that is amenable to low vapor pressure explosives, 2,4,6-trinitrotoluene and hexahydro-1,3,5-trinitro-1,3,5-triazine. The LIVG operates in a continuous manner, providing a constant and stable vapor output over a period of days and whose concentration can be extended over as much as three orders of magnitude. In addition, a large test atmosphere chamber attached to the LIVG is described, which enables the generation of a stable test atmosphere with controllable humidity and temperature. The size of the chamber allows for the complete insertion of testing instruments or arrays of materials into a uniform test atmosphere, and various electrical feedthroughs, insertion ports, and sealed doors permit simple and effective access to the sample chamber and its vapor.

40 CFR 71.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... control agency for the area in which a part 71 permit, permit modification, or permit renewal is being... requirement of the program to control air pollution from outer continental shelf sources, under section 328 of... particular change. Delegate agency means the State air pollution control agency, local agency, other State...

40 CFR 71.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... control agency for the area in which a part 71 permit, permit modification, or permit renewal is being... requirement of the program to control air pollution from outer continental shelf sources, under section 328 of... particular change. Delegate agency means the State air pollution control agency, local agency, other State...

40 CFR 71.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... control agency for the area in which a part 71 permit, permit modification, or permit renewal is being... requirement of the program to control air pollution from outer continental shelf sources, under section 328 of... particular change. Delegate agency means the State air pollution control agency, local agency, other State...

Intralesional steroid therapy of pyoderma gangrenosum.

PubMed

Goldstein, F; Krain, R; Thornton, J J

1985-12-01

Treatment of pyoderma gangrenosum complicating ulcerative colitis has in the past been frustrating and usually unsuccessful, frequently resulting in colectomy. Intralesional steroid therapy has been used off and on in a few patients, but the treatment is not widely known to gastroenterologists. We report two patients successfully treated for early pyoderma gangrenosum by intralesional injection of triamcinolone acetonide (Kenalog, 40 mg injection) together with conventional doses of systemic steroids. A single series of injections was sufficient to bring about healing of the lesions in both patients. The treatment permitted early discharge of patients from the hospital, and the skin lesions were completely healed within 2 months. The lesions have not recurred in follow-up examinations of 11/2 and 21/2 years, respectively. We hope that other physicians will find this approach equally effective.

40 CFR 147.1955 - Requirements for wells authorized by permit.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (ii) Cemented back to the surface by recirculating the cement; and (2) Long string casing and tubing... volume. (3) For new enhanced recovery wells, install tubing or long string casing extending to the injection zone. (4) For new salt water disposal wells, install long string casing and tubing extending to...

Analysis of trace impurities in neon by a customized gas chromatography.

PubMed

Yin, Min Kyo; Lim, Jeong Sik; Moon, Dong Min; Lee, Gae Ho; Lee, Jeongsoon

2016-09-09

Excimer lasers, widely used in the semiconductor industry, are crucial for analyzing the purity of premix laser gases for the purpose of controlling stable laser output power. In this study, we designed a system for analyzing impurities in pure neon (Ne) base gas by customized GC. Impurities in pure neon (H2 and He), which cannot be analyzed at the sub-μmol/mol level using commercial GC detectors, were analyzed by a customized pulsed-discharge Ne ionization detector (PDNeD) and a pressurized injection thermal conductivity detector using Ne as the carrier gas (Pres. Inj. Ne-TCD). From the results, trace species in Ne were identified with the following detection limits: H2, 0.378μmol/mol; O2, 0.119μmol/mol; CH4, 0.880μmol/mol; CO, 0.263μmol/mol; CO2, 0.162μmol/mol (PDNeD); and He, 0.190μmol/mol (Pres. Inj. Ne-TCD). This PDNeD and pressurized injection Ne-TCD technique thus developed permit the quantification of trace impurities present in high-purity Ne. Copyright © 2016. Published by Elsevier B.V.

Method for rigless zone abandonment using internally catalyzed resin system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, R.C.

1980-02-19

A zone of a subterranean formation penetrated by a well bore is permanently plugged by injecting a liquid resin system containing at least one thermosetting resin and at least one curing agent or catalyst therefor into the formation and injecting into the wellbore following the resin system, a second liquid containing at least one chain stopping compound to react with one component in the resin system to prevent any of the resin system remaining in the well bore from crosslinking to a sufficient crosslink density to form a solid in the wellbore. Preferably, the second liquid also contains a fluidmore » loss additive to minimize loss of the second liquid from the wellbore to the formation. The method permits a zone to be plugged off and abandoned without the need to erect a drilling rig to drill out excess plugging material remaining in the wellbore. In a preferred embodiment, the resin system comprises the diglycidyl ether of bisphenol a and polymethylene phenylamine in ethylene glycol ethyl ether, and the preferred second liquid is monoethanolamine in ethylene glycol ethyl ether as a solvent with ethylcellulose and silic flour to control fluid loss.« less

Composition for preventing a resin system from setting up in a well bore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, R. C.

1981-06-09

A zone of a subterranean formation penetrated by a well bore is permanently plugged by injecting a liquid resin system containing at least one thermosetting resin and at least one curing agent or catalyst therefor into the formation and injecting into the wellbore following the resin system, a second liquid containing at least one chain stopping compound to react with one component in the resin system to prevent any of the resin system remaining in the well bore from crosslinking to a sufficient crosslink density to form a solid in the wellbore. Preferably, the second liquid also contains a fluidmore » loss additive to minimize loss of the second liquid from the wellbore to the formation. The method permits a zone to be plugged off and abandoned without the need to erect a drilling rig to drill out excess plugging material remaining in the wellbore. In a preferred embodiment, the resin system comprises the diglycidyl ether of bisphenol a and polymethylene phenylamine in ethylene glycol ethyl ether, and the preferred second liquid is monoethanolamine in ethylene glycol ethyl ether as a solvent with ethylcellulose and silica flour to control fluid loss.« less

21 CFR 1312.23 - Issuance of export permit.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Issuance of export permit. 1312.23 Section 1312.23... CONTROLLED SUBSTANCES Exportation of Controlled Substances § 1312.23 Issuance of export permit. (a) The... regulation in § 1312.30 of this part be exported only pursuant to the issuance of an export permit. The...

The Expression of TALEN before Fertilization Provides a Rapid Knock-Out Phenotype in Xenopus laevis Founder Embryos.

PubMed

Miyamoto, Kei; Suzuki, Ken-Ichi T; Suzuki, Miyuki; Sakane, Yuto; Sakuma, Tetsushi; Herberg, Sarah; Simeone, Angela; Simpson, David; Jullien, Jerome; Yamamoto, Takashi; Gurdon, J B

2015-01-01

Recent advances in genome editing using programmable nucleases have revolutionized gene targeting in various organisms. Successful gene knock-out has been shown in Xenopus, a widely used model organism, although a system enabling less mosaic knock-out in founder embryos (F0) needs to be explored in order to judge phenotypes in the F0 generation. Here, we injected modified highly active transcription activator-like effector nuclease (TALEN) mRNA to oocytes at the germinal vesicle (GV) stage, followed by in vitro maturation and intracytoplasmic sperm injection, to achieve a full knock-out in F0 embryos. Unlike conventional injection methods to fertilized embryos, the injection of TALEN mRNA into GV oocytes allows expression of nucleases before fertilization, enabling them to work from an earlier stage. Using this procedure, most of developed embryos showed full knock-out phenotypes of the pigmentation gene tyrosinase and/or embryonic lethal gene pax6 in the founder generation. In addition, our method permitted a large 1 kb deletion. Thus, we describe nearly complete gene knock-out phenotypes in Xenopus laevis F0 embryos. The presented method will help to accelerate the production of knock-out frogs since we can bypass an extra generation of about 1 year in Xenopus laevis. Meantime, our method provides a unique opportunity to rapidly test the developmental effects of disrupting those genes that do not permit growth to an adult able to reproduce. In addition, the protocol shown here is considerably less invasive than the previously used host transfer since our protocol does not require surgery. The experimental scheme presented is potentially applicable to other organisms such as mammals and fish to resolve common issues of mosaicism in founders.

Potential for the Use of Wireless Sensor Networks for Monitoring of CO2 Leakage Risks

NASA Astrophysics Data System (ADS)

Pawar, R.; Illangasekare, T. H.; Han, Q.; Jayasumana, A.

2015-12-01

Storage of supercritical CO2 in deep saline geologic formation is under study as a means to mitigate potential global climate change from green house gas loading to the atmosphere. Leakage of CO2 from these formations poses risk to the storage permanence goal of 99% of injected CO2 remaining sequestered from the atmosphere,. Leaked CO2 that migrates into overlying groundwater aquifers may cause changes in groundwater quality that pose risks to environmental and human health. For these reasons, technologies for monitoring, measuring and accounting of injected CO2 are necessary for permitting of CO2 sequestration projects under EPA's class VI CO2 injection well regulations. While the probability of leakage related to CO2 injection is thought to be small at characterized and permitted sites, it is still very important to protect the groundwater resources and develop methods that can efficiently and accurately detect CO2 leakage. Methods that have been proposed for leakage detection include remote sensing, soil gas monitoring, geophysical techniques, pressure monitoring, vegetation stress and eddy covariance measurements. We have demonstrated the use of wireless sensor networks (WSN) for monitoring of subsurface contaminant plumes. The adaptability of this technology for leakage monitoring of CO2 through geochemical changes in the shallow subsurface is explored. For this technology to be viable, it is necessary to identify geochemical indicators such as pH or electrical conductivity that have high potential for significant change in groundwater in the event of CO2 leakage. This talk presents a conceptual approach to use WSNs for CO2 leakage monitoring. Based on our past work on the use of WSN for subsurface monitoring, some of the challenges that need to be over come for this technology to be viable for leakage detection will be discussed.

Turbulent boundary layer on a full-coverage film-cooled surface: An experimental heat transfer study with normal injection

NASA Technical Reports Server (NTRS)

Choe, H.; Kays, W. M.; Moffat, R. J.

1976-01-01

Heat transfer behavior was studied in a turbulent boundary layer with full-coverage film cooling through an array of discrete holes and with injection normal to the wall surface. Stanton numbers were measured for a staggered hole pattern with pitch-to-diameter ratios of 5 and 10, an injection mass flux ratio range of 0.1 to 1.0, and a range of Reynolds number 170 thousand to 5 million. Air was used as the working fluid with the mainstream velocity varied from .14 to 33.5 m/sec (30 to 110 ft/sec). The data were taken for secondary injection temperatures equal to the wall temperature and also equal to the mainstream temperature. By use of linear superposition theory, the data may be used to obtain Stanton number as a continuous function of the injectant temperature. The heat transfer coefficient is defined on the basis of a mainstream-to-wall temperature difference. This difinition permits direct comparison of performance between film cooling and transpiration cooling.

78 FR 32273 - Renewal of Agency Information Collection for Navajo Partitioned Lands Grazing Permits

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-29

... Permits authorized by OMB Control Number 1076-0162. This information collection expires May 31, 2013.... Data OMB Control Number: 1076-0162. Title: Navajo Partitioned Lands Grazing Permits, 25 CFR 161. Brief...

Final Scientific/Technical Report for project “Geomechanical Monitoring for CO 2 Hub Storage: Production and Injection at Kevin Dome

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daley, Thomas M.; Vasco, Don; Ajo-Franklin, Jonathan

After learning that the TDS value in the target injection formation at the Kevin Dome site is too low to qualify for an EPA Class VI CO2 injection permit, the BSCSP project was re-scoped such that injection of CO2 is no longer planned. With no injection planned, the Geomechanics project was closed. In this final report, we describe the objective and approach of the project as proposed, and the limited results obtained before stopping work. The objective of the proposed research was the development & validation of an integrated monitoring approach for quantifying the interactions between large-scale geological carbon storagemore » (GCS) and subsurface geomechanical state, particularly perturbations relevant to reservoir integrity such as fault reactivation and induced fracturing. In the short period of work before knowing the fate of the Kevin Dome project, we (1) researched designs for both the proposed InSAR corner reflectors as well as the near-surface 3C seismic stations; (2) developed preliminary elastic geomechanical models; (3) developed a second generation deformation prediction for the BSCSP Kevin Dome injection site; and (4) completed a preliminary map of InSAR monuments and shallow MEQ wells in the vicinity of the BSCSP injection pad.« less

Dynamic illumination of spatially restricted or large brain volumes via a single tapered optical fiber

PubMed Central

Pisanello, Marco; Oldenburg, Ian A.; Sileo, Leonardo; Markowitz, Jeffrey E.; Peterson, Ralph E.; Della Patria, Andrea; Haynes, Trevor M.; Emara, Mohamed S.; Spagnolo, Barbara; Datta, Sandeep Robert; De Vittorio, Massimo; Sabatini, Bernardo L.

2017-01-01

Optogenetics promises spatiotemporal precise control of neural processes using light. However, the spatial extent of illumination within the brain is difficult to control and cannot be adjusted using standard fiber optics. We demonstrate that optical fibers with tapered tips can be used to illuminate either spatially restricted or large brain volumes. Remotely adjusting the light input angle to the fiber varies the light-emitting portion of the taper over several millimeters without movement of the implant. We use this mode to activate dorsal versus ventral striatum of individual mice and reveal different effects of each manipulation on motor behavior. Conversely, injecting light over the full numerical aperture of the fiber results in light emission from the entire taper surface, achieving broader and more efficient optogenetic activation of neurons when compared to the standard flat-faced fiber stimulation. Thus, tapered fibers permit focal or broad illumination that can be precisely and dynamically matched to experimental needs. PMID:28628101

Dynamic illumination of spatially restricted or large brain volumes via a single tapered optical fiber.

PubMed

Pisanello, Ferruccio; Mandelbaum, Gil; Pisanello, Marco; Oldenburg, Ian A; Sileo, Leonardo; Markowitz, Jeffrey E; Peterson, Ralph E; Della Patria, Andrea; Haynes, Trevor M; Emara, Mohamed S; Spagnolo, Barbara; Datta, Sandeep Robert; De Vittorio, Massimo; Sabatini, Bernardo L

2017-08-01

Optogenetics promises precise spatiotemporal control of neural processes using light. However, the spatial extent of illumination within the brain is difficult to control and cannot be adjusted using standard fiber optics. We demonstrate that optical fibers with tapered tips can be used to illuminate either spatially restricted or large brain volumes. Remotely adjusting the light input angle to the fiber varies the light-emitting portion of the taper over several millimeters without movement of the implant. We use this mode to activate dorsal versus ventral striatum of individual mice and reveal different effects of each manipulation on motor behavior. Conversely, injecting light over the full numerical aperture of the fiber results in light emission from the entire taper surface, achieving broader and more efficient optogenetic activation of neurons, compared to standard flat-faced fiber stimulation. Thus, tapered fibers permit focal or broad illumination that can be precisely and dynamically matched to experimental needs.

78 FR 24229 - Renewal of Agency Information Collection for Grazing Permits

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-24

...) approval for the collection of information for Grazing Permits authorized by OMB Control Number 1076- 0157... guarantee that we will be able to do so. III. Data OMB Control Number: 1076-0157. Title: Grazing Permits, 25...

Fluoroscopically Guided Epidural Injections of the Cervical and Lumbar Spine.

PubMed

Shim, Euddeum; Lee, Joon Woo; Lee, Eugene; Ahn, Joong Mo; Kang, Yusuhn; Kang, Heung Sik

2017-01-01

Advances in imaging and the development of injection techniques have enabled spinal intervention to become an important tool in managing chronic spinal pain. Epidural steroid injection (ESI) is one of the most widely used spinal interventions; it directly delivers drugs into the epidural space to relieve pain originating from degenerative spine disorders-central canal stenoses and neural foraminal stenoses-or disk herniations. Knowledge of the normal anatomy of the epidural space is essential to perform an effective and safe ESI and to recognize possible complications. Although computed tomographic (CT) or combined CT-fluoroscopic guidance has been increasingly used in ESI, conventional fluoroscopic guidance is generally performed. In ESI, drugs are delivered into the epidural space by interlaminar or transforaminal routes in the cervical spine or by interlaminar, transforaminal, or caudal routes in the lumbar spine. Epidurography is usually performed before drug delivery to verify the proper position of the needle in the epidural space. A small amount of contrast agent is injected with fluoroscopic guidance. Familiarity with the findings on a typical "true" epidurogram (demonstrating correct needle placement in the epidural space) permits proper performance of ESI. Findings on "false" epidurograms (demonstrating incorrect needle placement) include muscular staining and evidence of intravascular injection, inadvertent facet joint injection, dural puncture, subdural injection, and intraneural or intradiscal injection. © RSNA, 2016 An earlier incorrect version of this article appeared online. This article was corrected on December 22, 2016.

STELLARATOR INJECTOR

DOEpatents

Post, R.F.

1962-09-01

A method and means are described for injecting energetic neutral atoms or molecular ions into dense magnetically collimated plasma columns of stellarators and the like in such a manner that the atoms or ions are able to significantly penetrate the column before being ionized by collision with the plasma constituent particles. Penetration of the plasma column by the neutral atoms or molecular ions is facilitated by superposition of two closely spaced magnetic mirrors on the plasma confinement field. The mirrors are moved apart to magnetically sweep plasma from a region between the mirrors and establish a relatively low plasma density therein. By virture of the low density, neutral atoms or molecular ions injected into the region significantly penetrate the plasma column before being ionized. Thereafter, the mirrors are diminished to permit the injected material to admix with the plasma in the remainder of the column. (AEC)

Some Factors Affecting Combustion in an Internal-Combustion Engine

NASA Technical Reports Server (NTRS)

Rothrock, A M; Cohn, Mildred

1936-01-01

An investigation of the combustion of gasoline, safety, and diesel fuels was made in the NACA combustion apparatus under conditions of temperature that permitted ignition by spark with direct fuel injection, in spite of the compression ratio of 12.7 employed. The influence of such variables as injection advance angle, jacket temperature, engine speed, and spark position was studied. The most pronounced effect was that an increase in the injection advance angle (beyond a certain minimum value) caused a decrease in the extent and rate of combustion. In almost all cases combustion improved with increased temperature. The results show that at low air temperatures the rates of combustion vary with the volatility of the fuel, but that at high temperatures this relationship does not exist and the rates depend to a greater extent on the chemical nature of the fuel.

The feasibility of water injection into the turbine coolant to permit gas turbine contingency power for helicopter application

NASA Technical Reports Server (NTRS)

Van Fossen, G. J.

1983-01-01

It is pointed out that in certain emergency situations it may be desirable to obtain power from a helicopter engine at levels greater than the maximum rating. Yost (1976) has reported studies concerning methods of power augmentation in the one engine inoperative (OEI) case. It was found that a combination of water/alcohol injection into the inlet and overtemperature/overspeed could provide adequate emergency power. The present investigation is concerned with the results of a feasibility study which analytically investigated the maximum possible level of augmentation with constant gas generator turbine stress rupture life as a constraint. In the proposed scheme, the increased engine output is obtained by turbine overtemperature, however, the temperature of the compressor bleed air used for hot section cooling is lowered by injecting and evaporating water.

DETERMINATION OF PESTICIDES IN COMPOSITE DIETARY SAMPLES BY GAS CHROMATOGRAPHY/MASS SPECTROMETRY IN THE SELECTED ION MONITORING MODE USING A TEMPERATURE PROGRAMMABLE LARGE VOLUME INJECTOR WITH PRE-SEPARATION COLUMN

EPA Science Inventory

Use of a temperature-programmable pre-separation column in the gas chromatographic injection port permits determination of a wide range of semi-volatile pesticides including organochlorines, organophosphates, triazines, and anilines in fatty composite dietary samples while reduci...

Creating unstable velocity-space distributions with barium injections

NASA Technical Reports Server (NTRS)

Pongratz, M. B.

1983-01-01

Ion velocity-space distributions resulting from barium injections from orbiting spacecraft and shaped charges are discussed. Active experiments confirm that anomalous ionization processes may operate, but photoionization accounts for the production of the bulk of the barium ions. Pitch-angle diffusion and/or velocity-space diffusion may occur, but observations of barium ions moving upwards against gravity suggests that the ions retain a significant enough fraction of their initial perpendicular velocity to provide a mirror force. The barium ion plasmas should have a range of Alfven Mach numbers and plasma betas. Because the initial conditions can be predicted these active experiments should permit testing plasma instability hypotheses.

Properties of radio-frequency heated argon confined uranium plasmas

NASA Technical Reports Server (NTRS)

1976-01-01

Pure uranium hexafluoride (UF6) was injected into an argon confined, steady state, rf-heated plasma within a fused silica peripheral wall test chamber. Exploratory tests conducted using an 80 kW rf facility and different test chamber flow configurations permitted selection of the configuration demonstrating the best confinement characteristics and minimum uranium compound wall coating. The overall test results demonstrated applicable flow schemes and associated diagnostic techniques were developed for the fluid mechanical confinement and characterization of uranium within an rf plasma discharge when pure UF6 is injected for long test times into an argon-confined, high-temperature, high-pressure, rf-heated plasma.

77 FR 23803 - Office of Hazardous Materials Safety; Actions on Special Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-20

... MODIFICATION SPECIAL PERMIT GRANTED 8826-M Phoenix Air 49 CFR 172.101; To modify the Group, Inc. 172.204(c)(3...-M......... Conference of 49 CFR To modify the Radiation 172.203(d); special permit add Control Part............ Conference of 49 CFR Part To modify the Radiation 172, Subparts, special permit add Control C, D, E, F, G, 49...

From basic concepts to emerging technologies in regional anesthesia.

PubMed

Dillane, Derek; Tsui, Ban C H

2010-10-01

The present article details how our understanding of the basic concepts of regional anesthesia has recently evolved. We will appraise current technological advances and question the commensurate nature of the relationship between tradition and innovation. Ultrasound localization has enhanced our understanding of the needle-nerve relationship. Intraneural injection of local anesthetic may occur with greater frequency than previously thought without inevitably leading to neurological complications. The ratio of neural to non-neural tissue varies both between and within nerves and may be an important determinant of neural injury. Ultrasonographic evidence of intraneural injection is subject to observer expertise and the resolution of the ultrasound image. Current ultrasound resolution capability does not reliably permit differentiation between intrafascicular and extrafascicular drug injection. Perineural electrical impedance may be a determinant of current threshold and conceivably distinguish between intraneural and extraneural tissue. Technology that enhances the sonographic image of both procedure needle and target nerve is the focus of current endeavors in ultrasound innovation.There is inconclusive evidence that the use of ultrasound technology has reduced the incidence of local anesthetic toxicity. Lipid emulsion therapy is now an accepted treatment for systemic local anesthetic toxicity. There are new reports on the development of an ultra long-acting local anesthetic agent that would permit lower doses and superannuate catheter-based continuous regional anesthesia techniques. Over the past decade, our understanding of the fundamental concepts of regional anesthesia continues to be challenged by emerging experimental and clinical evidence.

Clinical and cost-effectiveness of progressive exercise compared with best practice advice, with or without corticosteroid injection, for the treatment of rotator cuff disorders: protocol for a 2x2 factorial randomised controlled trial (the GRASP trial).

PubMed

Hopewell, Sally; Keene, David J; Maia Schlüssel, Michael; Dritsaki, Melina; Dutton, Susan; Carr, Andrew; Hamilton, William; Hansen, Zara; Jaggi, Anju; Littlewood, Chris; Soutakbar, Hessam; Heine, Peter; Cureton, Lucy; Barker, Karen; Lamb, Sarah E

2017-07-17

Shoulder pain is very common, with around 70% of cases due to disorders of the rotator cuff. Despite widespread provision of physiotherapy, there is uncertainty about which type of exercise and delivery mechanisms are associated with best outcomes. There is also uncertainty around the long-term benefits and harms of corticosteroid injection therapy, which is often used in addition to physiotherapy. The Getting it Right: Addressing Shoulder Pain trial will assess the clinical and cost-effectiveness of individually tailored, progressive exercise compared with best practice advice, with or without corticosteroid injection, in adults with a rotator cuff disorder. We are conducting a large multicentre randomised controlled trial (2×2 factorial design). We will recruit adults ≥18 years with a new episode of shoulder pain attributable to a rotator cuff disorder as per British Elbow and Shoulder Society guidelines, not currently receiving physiotherapy or being considered for surgery, from at least eight UK National Health Service primary care-based musculoskeletal and related physiotherapy services. Participants (n=704) will be randomised (centralised computer-generated 1:1:1:1 allocation ratio) to one of four interventions: (1) progressive exercise (≤6 physiotherapy sessions); (2) best practice advice (one physiotherapy session); (3) corticosteroid injection then progressive exercise (≤6 sessions) or (4) corticosteroid injection then best practice advice (one session). The primary outcome is the mean difference in Shoulder Pain and Disability Index (SPADI) total score at 12 months. Secondary outcomes are: pain and function SPADI subdomains; health-related quality of life (Five-Level version of the EuroQol EQ-5D-5L); sleep disturbance; return to activity; global impression of change; health resource use; out-of-pocket expenses; work disability. A parallel within-trial economic evaluation will be conducted. The primary analysis will be intention to treat. Research Ethics Committee approval (REC: 16/SC/0508) has been obtained. Results of the main trial and secondary outcomes will be submitted for publication in a peer-reviewed journal. ISRCTN16539266; EudraCT number: 2016-002991-28. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Development of integrated control system for smart factory in the injection molding process

NASA Astrophysics Data System (ADS)

Chung, M. J.; Kim, C. Y.

2018-03-01

In this study, we proposed integrated control system for automation of injection molding process required for construction of smart factory. The injection molding process consists of heating, tool close, injection, cooling, tool open, and take-out. Take-out robot controller, image processing module, and process data acquisition interface module are developed and assembled to integrated control system. By adoption of integrated control system, the injection molding process can be simplified and the cost for construction of smart factory can be inexpensive.

21 CFR 1210.21 - Permit number.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Permit number. 1210.21 Section 1210.21 Food and... IMPORT MILK ACT Permit Control § 1210.21 Permit number. Each permit issued under the Federal Import Milk Act, including each temporary permit, shall bear an individual number. The right to the use of such...

21 CFR 1210.21 - Permit number.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Permit number. 1210.21 Section 1210.21 Food and... IMPORT MILK ACT Permit Control § 1210.21 Permit number. Each permit issued under the Federal Import Milk Act, including each temporary permit, shall bear an individual number. The right to the use of such...

21 CFR 1210.21 - Permit number.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Permit number. 1210.21 Section 1210.21 Food and... IMPORT MILK ACT Permit Control § 1210.21 Permit number. Each permit issued under the Federal Import Milk Act, including each temporary permit, shall bear an individual number. The right to the use of such...

Expanding Non-solenoidal Startup with Local Helicity Injection to Increased Toroidal Field and Helicity Injection Rate

NASA Astrophysics Data System (ADS)

Perry, J. M.; Barr, J. L.; Bodner, G. M.; Bongard, M. W.; Burke, M. G.; Fonck, R. J.; Hinson, E. T.; Lewicki, B. T.; Reusch, J. A.; Schlossberg, D. J.; Winz, G. R.

2015-11-01

Local helicity injection (LHI) is a non-solenoidal startup technique under development on the Pegasus ST. Plasma currents up to 0.18 MA have been initiated by LHI in conjunction with poloidal field induction. A 0-D power balance model has been developed to predict plasma current evolution by balancing helicity input against resistive dissipation. The model is being validated against a set of experimental measurements and magnetic reconstructions with radically varied plasma geometric evolutions. Outstanding physics issues with LHI startup are the scalings of confinement and MHD activity with helicity injection rate and toroidal field strength, as well as injector behavior at high field. Preliminary results from the newly-installed Thomson scattering system suggest core temperatures of a few hundred eV during LHI startup. Measurements are being expanded to multiple spatial points for ongoing confinement studies. A set of larger-area injectors is being installed in the lower divertor region, where increased toroidal field will provide a helicity injection rate over 3 times that of outboard injectors. In this regime helicity injection will be the dominant current drive. Experiments with divertor injectors will permit experimental differentiation of several possible confinement models, and demonstrate the feasibility of LHI startup at high field. Work supported by US DOE grant DE-FG02-96ER54375.

31 CFR 592.201 - Prohibited importation and exportation of any rough diamond; permitted importation or exportation...

Code of Federal Regulations, 2011 CFR

2011-07-01

... of any rough diamond; permitted importation or exportation of any rough diamond. 592.201 Section 592... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY ROUGH DIAMONDS CONTROL REGULATIONS Prohibitions § 592.201 Prohibited importation and exportation of any rough diamond; permitted importation or exportation...

31 CFR 592.201 - Prohibited importation and exportation of any rough diamond; permitted importation or exportation...

Code of Federal Regulations, 2012 CFR

2012-07-01

... of any rough diamond; permitted importation or exportation of any rough diamond. 592.201 Section 592... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY ROUGH DIAMONDS CONTROL REGULATIONS Prohibitions § 592.201 Prohibited importation and exportation of any rough diamond; permitted importation or exportation...

31 CFR 592.201 - Prohibited importation and exportation of any rough diamond; permitted importation or exportation...

Code of Federal Regulations, 2013 CFR

2013-07-01

... of any rough diamond; permitted importation or exportation of any rough diamond. 592.201 Section 592... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY ROUGH DIAMONDS CONTROL REGULATIONS Prohibitions § 592.201 Prohibited importation and exportation of any rough diamond; permitted importation or exportation...

31 CFR 592.201 - Prohibited importation and exportation of any rough diamond; permitted importation or exportation...

Code of Federal Regulations, 2014 CFR

2014-07-01

... of any rough diamond; permitted importation or exportation of any rough diamond. 592.201 Section 592... FOREIGN ASSETS CONTROL, DEPARTMENT OF THE TREASURY ROUGH DIAMONDS CONTROL REGULATIONS Prohibitions § 592.201 Prohibited importation and exportation of any rough diamond; permitted importation or exportation...

21 CFR 358.720 - Permitted combinations of active ingredients.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 5 2014-04-01 2014-04-01 false Permitted combinations of active ingredients. 358... Permitted combinations of active ingredients. (a) Combination of active ingredients for the control of... labeled according to § 358.750. (b) Combination of control of dandruff and external analgesic active...

21 CFR 358.720 - Permitted combinations of active ingredients.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Permitted combinations of active ingredients. 358... Permitted combinations of active ingredients. (a) Combination of active ingredients for the control of... labeled according to § 358.750. (b) Combination of control of dandruff and external analgesic active...

21 CFR 358.720 - Permitted combinations of active ingredients.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 5 2012-04-01 2012-04-01 false Permitted combinations of active ingredients. 358... Permitted combinations of active ingredients. (a) Combination of active ingredients for the control of... labeled according to § 358.750. (b) Combination of control of dandruff and external analgesic active...

21 CFR 358.720 - Permitted combinations of active ingredients.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 5 2011-04-01 2011-04-01 false Permitted combinations of active ingredients. 358... Permitted combinations of active ingredients. (a) Combination of active ingredients for the control of... labeled according to § 358.750. (b) Combination of control of dandruff and external analgesic active...

21 CFR 358.720 - Permitted combinations of active ingredients.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 5 2013-04-01 2013-04-01 false Permitted combinations of active ingredients. 358... Permitted combinations of active ingredients. (a) Combination of active ingredients for the control of... labeled according to § 358.750. (b) Combination of control of dandruff and external analgesic active...

Monitoring Knowledge Base (MKB)

EPA Pesticide Factsheets

The Monitoring Knowledge Base (MKB) is a compilation of emissions measurement and monitoring techniques associated with air pollution control devices, industrial process descriptions, and permitting techniques, including flexible permit development. Using MKB, one can gain a comprehensive understanding of emissions sources, control devices, and monitoring techniques, enabling one to determine appropriate permit terms and conditions.

Delayed near-infrared analysis permits visualization of rodent retinal pigment epithelium layer in vivo

NASA Astrophysics Data System (ADS)

Pankova, Natalie; Zhao, Xu; Liang, Huiyuan; Baek, David Sung Hyeon; Wang, Hai; Boyd, Shelley

2014-07-01

Patches of atrophy of the retinal pigment epithelium (RPE) have not been described in rodent models of retinal degeneration, as they have the clinical setting using fundus autofluorescence. We hypothesize that prelabeling the RPE would increase contrast and allow for improved visualization of RPE loss in vivo. Here, we demonstrate a new technique termed "delayed near-infrared analysis (DNIRA)" that permits ready detection of rat RPE, using optical imaging in the near-infrared (IR) spectrum with aid of indocyanine green (ICG) dye. Using DNIRA, we demonstrate a fluorescent RPE signal that is detected using confocal scanning laser ophthalmoscopy up to 28 days following ICG injection. This signal is apparent only after ICG injection, is dose dependent, requires the presence of the ICG filters (795/810 nm excitation/emission), does not appear in the IR reflectance channel, and is eliminated in the presence of sodium iodate, a toxin that causes RPE loss. Rat RPE explants confirm internalization of ICG dye. Together with normal retinal electrophysiology, these findings demonstrate that DNIRA is a new and safe noninvasive optical imaging technique for in vivo visualization of the RPE in models of retinal disease.

[To kill, let die and euthanasia in the bill of rights of patients and in the Chilean doctrine].

PubMed

Figueroa G, Rodolfo

2011-05-01

The Bill of Rights for Patients provides the patient with autonomy for disposing of his life, enabling him to reject those treatments that unnecessarily prolong his life. However, the bill does not allow an artificial acceleration of death. Therefore, the bill does not permit euthanasia (at least, certain form of it) nor assisted-suicide. However, according to the practice of medicine and also Chilean doctrine, it is permitted to inject morphine to a patient to relieve his pain, even though that could hasten his death. In consequence, it is allowed for the patient to dispose of his life and also to inject in him morphine for pain relief, endangering his life, but neither euthanasia nor assisted-suicide is allowed. Is this coherent? According to Chilean doctrine, it could be coherent under the condition of accepting the distinction between killing and letting die and also the double effect doctrine. The problem is that there is abundant English literature in the realm of moral philosophy to disregard both conditions. Therefore, it is possible to claim that the Bill is not coherent and that the Chilean doctrine is based upon a distinction and a doctrine that are not acceptable.

Design, assembly, and optical bench testing of a high-numerical-aperture miniature injection-molded objective for fiber-optic confocal reflectance microscopy.

PubMed

Chidley, Matthew D; Carlson, Kristen D; Richards-Kortum, Rebecca R; Descour, Michael R

2006-04-10

The design, analysis, assembly methods, and optical-bench test results for a miniature injection-molded plastic objective lens used in a fiber-optic confocal reflectance microscope are presented. The five-lens plastic objective was tested as a stand-alone optical system before its integration into a confocal microscope for in vivo imaging of cells and tissue. Changing the spacing and rotation of the individual optical elements can compensate for fabrication inaccuracies and improve performance. The system performance of the miniature objective lens is measured by use of an industry-accepted slanted-edge modulation transfer function (MTF) metric. An estimated Strehl ratio of 0.61 and a MTF value of 0.66 at the fiber-optic bundle Nyquist frequency have been obtained. The optical bench testing system is configured to permit interactive optical alignment during testing to optimize performance. These results are part of an effort to demonstrate the manufacturability of low-cost, high-performance biomedical optics for high-resolution in vivo imaging. Disposable endoscopic microscope objectives could help in vivo confocal microscopy technology mature to permit wide-scale clinical screening and detection of early cancers and precancerous lesions.

77 FR 66406 - Migratory Bird Permits; Delegating Falconry Permitting Authority to Seven States

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-05

...-1231-9BPP] RIN 1018-AZ16 Migratory Bird Permits; Delegating Falconry Permitting Authority to Seven... requirements of the Migratory Bird Permits Program and assigned OMB control number 1018- 0022, which expires... chapter I, title 50 of the Code of Federal Regulations, as follows: PART 21--MIGRATORY BIRD PERMITS 0 1...

INJECTION-MOLDING APPARATUS

DOEpatents

Lobell, G.M.

1958-02-11

This patent is drawn to an injection molding apparatus for producing a tube closed at one end wherein the normally unsupported end of the core located in the cavity during the injection of the molten material to fill the space between the core and cavity wall, which supporting means is automatically removed from operation during the forming of the closed end of the tube. This support means is a plug extending through the end of the core into a recess in the bottom of the cavity where the closed end of the tube is to be formed. The plug is spring pressed into said recess and is forced out of the recess by a slidable bushing at the top of the cavity which is moved against the force of the spring by the molten material when it fills the uppormost open end portion of the cavity, thereby permitting the closed end of the tube to be formed.

Outdoor Advertising Control

DOT National Transportation Integrated Search

2002-04-22

The State of Montana agreed to provide "effective control" of outdoor adervtising by establishing a sign permit system; maintenance of an inventory of all permitted signs, and a periodic surveillance of the controlled routes to disvover unlawful sign...

21 CFR 1210.21 - Permit number.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Permit number. 1210.21 Section 1210.21 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) REGULATIONS... IMPORT MILK ACT Permit Control § 1210.21 Permit number. Each permit issued under the Federal Import Milk...

21 CFR 1210.21 - Permit number.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Permit number. 1210.21 Section 1210.21 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) REGULATIONS... IMPORT MILK ACT Permit Control § 1210.21 Permit number. Each permit issued under the Federal Import Milk...

Triaxial Swirl Injector Element for Liquid-Fueled Engines

NASA Technical Reports Server (NTRS)

Muss, Jeff

2010-01-01

A triaxial injector is a single bi-propellant injection element located at the center of the injector body. The injector element consists of three nested, hydraulic swirl injectors. A small portion of the total fuel is injected through the central hydraulic injector, all of the oxidizer is injected through the middle concentric hydraulic swirl injector, and the balance of the fuel is injected through an outer concentric injection system. The configuration has been shown to provide good flame stabilization and the desired fuel-rich wall boundary condition. The injector design is well suited for preburner applications. Preburner injectors operate at extreme oxygen-to-fuel mass ratios, either very rich or very lean. The goal of a preburner is to create a uniform drive gas for the turbomachinery, while carefully controlling the temperature so as not to stress or damage turbine blades. The triaxial injector concept permits the lean propellant to be sandwiched between two layers of the rich propellant, while the hydraulic atomization characteristics of the swirl injectors promote interpropellant mixing and, ultimately, good combustion efficiency. This innovation is suited to a wide range of liquid oxidizer and liquid fuels, including hydrogen, methane, and kerosene. Prototype testing with the triaxial swirl injector demonstrated excellent injector and combustion chamber thermal compatibility and good combustion performance, both at levels far superior to a pintle injector. Initial testing with the prototype injector demonstrated over 96-percent combustion efficiency. The design showed excellent high -frequency combustion stability characteristics with oxygen and kerosene propellants. Unlike the more conventional pintle injector, there is not a large bluff body that must be cooled. The absence of a protruding center body enhances the thermal durability of the triaxial swirl injector. The hydraulic atomization characteristics of the innovation allow the design to be rapidly scaled from small in-space applications [500-5,000 lbf (2.2 22.2 kN)] to large thrust engine applications [80,000 lbf (356 kN) and beyond]. The triaxial injector is also less sensitive to eccentricities, manufacturing tolerances, and gap width of many traditional coaxial and pintle injector designs. The triaxial-injector injection orifice configuration provides for high injection stiffness. The low parts count and relatively large injector design features are amenable to low-cost production.

An Environment for Hardware-in-the-Loop Formation Navigation and Control Simulation

NASA Technical Reports Server (NTRS)

Burns, Rich

2004-01-01

Recent interest in formation flying satellite systems has spurred a considerable amount of research in the relative navigation and control of satellites. Development in this area has included new estimation and control algorithms as well as sensor and actuator development specifically geared toward the relative control problem. This paper describes a simulation facility, the Formation Flying Testbed (FFTB) at NASA's Goddard Space Flight Center, which allows engineers to test new algorithms for the formation flying problem with relevant GN&C hardware in a closed loop simulation. The FFTB currently supports the injection of GPS receiver hardware into the simulation loop, and support for satellite crosslink ranging technology is at a prototype stage. This closed-loop, hardware inclusive simulation capability permits testing of navigation and control software in the presence of the actual hardware with which the algorithms must interact. This capability provides the navigation or control developer with a perspective on how the algorithms perform as part of the closed-loop system. In this paper, the overall design and evolution of the FFTB are presented. Each component of the FFTB is then described in detail. Interfaces between the components of the FFTB are shown and the interfaces to and between navigation and control software are described in detail. Finally, an example of closed-loop formation control with GPS receivers in the loop is presented and results are analyzed.

RACT/BACT/LAER Clearninghouse (RBLC)

EPA Pesticide Factsheets

OAR's RACT, BACT, LAER Clearinghouse (RBLC) data asset contains summary information on selected air permitting actions from EPA, state, and local permitting agencies across the U.S., as well as a number of international permit records supplied by air pollution control agencies in Mexico and Canada. The acronyms refer to program requirements of the New Source Review (NSR) program: RACT is Reasonably Available Control Technology and applies to existing sources in areas that are not meeting national ambient air quality standards (i.e., non-attainment areas); BACT is Best Available Control Technology and applies to major new or modified sources in clean areas (i.e., attainment areas). LAER, or Lowest Achievable Emission Rate, is required on major new or modified sources in non-attainment areas. As of 2012, RBLC includes approximately 6,500 entries. With the exception of LAER permit determinations, whose inclusion in RBLC is mandatory, participation is voluntary. Coverage is therefore not complete or necessarily representative.Required under Section 108 of the 1990 Amendments to the Clean Air Act, RBLC provides users 00e2?? typically permit writers, permit applicants or holders, and the public 00e2?? with references and personal contacts to support ongoing air pollution control activities. Information is detailed enough for users to know whether a permit is applicable to their needs. Users may then contact the appropriate agency to access the permit or discuss it wit

78 FR 42520 - Control Technology, Inc.; Notice of Preliminary Permit Application Accepted for Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-16

... Technology, Inc.; Notice of Preliminary Permit Application Accepted for Filing and Soliciting Comments, Motions To Intervene, and Competing Applications On December 18, 2012, Control Technology, Inc. filed an application for a preliminary permit, pursuant to section 4(f) of the Federal Power Act, proposing to study...

76 FR 56982 - Approval and Promulgation of Implementation Plans; Texas; Revisions to Permits by Rule and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-15

... Pollution by Permits for New Construction or Modification AGENCY: Environmental Protection Agency (EPA... in Title 30 of the Texas Administrative Code (TAC), Chapter 116--Control of Air Pollution by Permits... [email protected] . List of Subjects in 40 CFR Part 52 Environmental protection, Air pollution control...

Responses to central oxotremorine and scopolamine support the cholinergic control of male mating behavior in hamsters.

PubMed

Floody, Owen R; Lusk, Laina G

2013-04-01

The responses of hamsters to intracranial injections of the cholinergic agonist oxotremorine (OXO) implicate cholinergic mechanisms in the medial preoptic area (MPOA) in the control of male mating behavior. To extend these observations, we ran three studies of responses to cholinergic drugs delivered singly or in combination to the vicinity of the MPOA. The first tested responses to OXO, confirming its ability to reduce the postejaculatory interval. The second complemented the first by examining responses to MPOA microinjections of the cholinergic antagonist scopolamine (SCO). These caused several changes revolving around intromission. These included increases in intromission frequency and ejaculation latency. They also included a change in the patterning of intromissions, marked by continuous strings without the usual separation by dismounts. The final study resembled the others in examining the effects of MPOA injections of OXO and SCO but focused on the ability of each drug to antagonize responses to the other. Most of the responses to OXO and SCO individually replicated earlier findings, though the measures examined here also permitted the description of effects on some noncopulatory sexual behaviors, specifically the male's inspection of the female. However, the most interesting results may be those suggesting asymmetry in the responses to the addition of the second drug: Whereas responses to OXO tended to be antagonized by SCO, OXO was less effective at counteracting responses to SCO. Though the explanation of this asymmetry is not completely clear, it is consistent with previous suggestions of differences in the affinities of these drugs for subtypes of muscarinic receptors. Therefore, it suggests that the cholinergic synapses and circuits controlling distinct elements of male behavior could differ in their dependence on these receptors. Copyright © 2013 Elsevier Inc. All rights reserved.

Management of primary achalasia: The role of endoscopy

PubMed Central

Luján-Sanchis, Marisol; Suárez-Callol, Patricia; Monzó-Gallego, Ana; Bort-Pérez, Inmaculada; Plana-Campos, Lydia; Ferrer-Barceló, Luis; Sanchis-Artero, Laura; Llinares-Lloret, María; Tuset-Ruiz, Juan Antonio; Sempere-Garcia-Argüelles, Javier; Canelles-Gamir, Pilar; Medina-Chuliá, Enrique

2015-01-01

Achalasia is an oesophageal motor disorder which leads to the functional obstruction of the lower oesophageal sphincter (LES) and is currently incurable. The main objective of all existing therapies is to achieve a reduction in the obstruction of the distal oesophagus in order to improve oesophageal transit, relieve the symptomatology, and prevent long-term complications. The most common treatments used are pneumatic dilation (PD) and laparoscopic Heller myotomy, which involves partial fundoplication with comparable short-term success rates. The most economic non-surgical therapy is PD, with botulinum toxin injections reserved for patients with a higher surgical risk for whom the former treatment option is unsuitable. A new technology is peroral endoscopic myotomy, postulated as a possible non-invasive alternative to surgical myotomy. Other endoluminal treatments subject to research more recently include injecting ethanolamine into the LES and using a temporary self-expanding metallic stent. At present, there is not enough evidence permitting a routine recommendation of any of these three novel methods. Patients must undergo follow-up after treatment to guarantee that their symptoms are under control and to prevent complications. Most experts are in favour of some form of endoscopic follow-up, however no established guidelines exist in this respect. The prognosis for patients with achalasia is good, although a recurrence after treatment using any method requires new treatment. PMID:26078828

75 FR 60457 - Underground Injection Control Program Hazardous Waste Injection Restrictions; Petition for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-30

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9208-4] Underground Injection Control Program Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection Dow Chemical Company (DOW... Petition. SUMMARY: Notice is hereby given that an exemption to the land disposal restrictions under the...

78 FR 42776 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-17

... ENVIRONMENTAL PROTECTION AGENCY [FRL9834-8] Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; Blanchard Refining... migration petition reissuance. SUMMARY: Notice is hereby given that a reissuance of an exemption to the land...

Integrated on-line system for DNA sequencing by capillary electrophoresis: From template to called bases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ton, H.; Yeung, E.S.

1997-02-15

An integrated on-line prototype for coupling a microreactor to capillary electrophoresis for DNA sequencing has been demonstrated. A dye-labeled terminator cycle-sequencing reaction is performed in a fused-silica capillary. Subsequently, the sequencing ladder is directly injected into a size-exclusion chromatographic column operated at nearly 95{degree}C for purification. On-line injection to a capillary for electrophoresis is accomplished at a junction set at nearly 70{degree}C. High temperature at the purification column and injection junction prevents the renaturation of DNA fragments during on-line transfer without affecting the separation. The high solubility of DNA in and the relatively low ionic strength of 1 x TEmore » buffer permit both effective purification and electrokinetic injection of the DNA sample. The system is compatible with highly efficient separations by a replaceable poly(ethylene oxide) polymer solution in uncoated capillary tubes. Future automation and adaptation to a multiple-capillary array system should allow high-speed, high-throughput DNA sequencing from templates to called bases in one step. 32 refs., 5 figs.« less

78 FR 19649 - Proposed Information Collection; Comment Request; Southwest Region Permit Family of Forms

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-02

... Federally-managed fisheries off the West Coast. There are three types of permits: Basic fishery permits for... fishing permits (EFPs). Appeals and certain waiver requests may also be submitted. Transfer applications... Species permits by April 30, 2013. III. Data OMB Control Number: 0648-0204. Form Number: None. Type of...

30 CFR 903.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., Article 1. (9) Fish and Wildlife Coordination Act, 16 U.S.C. 661-667. (10) Noise Control Act, 42 U.S.C...-256); (iv) Solid waste and air pollution discharge permits, installation and operation permits required for equipment causing air pollution and water pollution discharge permits (A.R.S. Title 49); (v...

30 CFR 903.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., Article 1. (9) Fish and Wildlife Coordination Act, 16 U.S.C. 661-667. (10) Noise Control Act, 42 U.S.C...-256); (iv) Solid waste and air pollution discharge permits, installation and operation permits required for equipment causing air pollution and water pollution discharge permits (A.R.S. Title 49); (v...

30 CFR 903.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., Article 1. (9) Fish and Wildlife Coordination Act, 16 U.S.C. 661-667. (10) Noise Control Act, 42 U.S.C...-256); (iv) Solid waste and air pollution discharge permits, installation and operation permits required for equipment causing air pollution and water pollution discharge permits (A.R.S. Title 49); (v...

30 CFR 903.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Article 1. (9) Fish and Wildlife Coordination Act, 16 U.S.C. 661-667. (10) Noise Control Act, 42 U.S.C...-256); (iv) Solid waste and air pollution discharge permits, installation and operation permits required for equipment causing air pollution and water pollution discharge permits (A.R.S. Title 49); (v...

77 FR 34382 - Meetings of the National Drinking Water Advisory Council-Notice of Public Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-11

...The U.S. Environmental Protection Agency (EPA or agency) is announcing one public webinar/conference call and one in-person meeting of the National Drinking Water Advisory Council (NDWAC or Council), established under the Safe Drinking Water Act (SDWA). The Council will consider various issues associated with drinking water protection and public water systems. For the webinar/conference call, the Council will discuss a draft guidance for EPA permit writers relative to hydraulic fracturing using diesel fuels under the SDWA's Underground Injection Control (UIC) Program and also options for assisting small water systems in achieving sustainable practices. For the in-person meeting, the primary focus will be for the Council to discuss the proposed regulation of perchlorate under the SDWA. Also at this in-person meeting, the Council will discuss assistance to small water systems among other program issues.

Improvements in ion reflux: An electrodialytic eluent generation and suppression device for ion chromatography.

PubMed

Elkin, Kyle; Riviello, John; Small, Hamish

2015-07-17

This work describes a membrane based electrodialytic ion reflux device (IRD), which uses water as the pumped phase and integrates isocratic and gradient eluent generation and suppression. The current design incorporates several ion exchange membranes to create discrete chambers for suppression and eluent generation, while isolating the electrodes from the analytical stream. A small volume of recycled water can be used as the pumped phase while continuously refluxing the eluent ions. This current design permits electronically controlled eluent generation of at least 16.4μeq KOHmin(-1), while maintaining low suppressed background conductivity (<0.5μS/cm). The device was operated in gradient or isocratic mode continuously for up to 6 weeks. During this period, over 500 gradient and isocratic injections were performed, showing peak retention time precision below 1.5% RSD. Published by Elsevier B.V.

A device for controlled jet injection of large volumes of liquid.

PubMed

Mckeage, James W; Ruddy, Bryan P; Nielsen, Poul M F; Taberner, Andrew J

2016-08-01

We present a needle-free jet injection device controllably actuated by a voice coil and capable of injecting up to 1.3 mL. This device is used to perform jet injections of ~900 μL into porcine tissue. This is the first time that delivery of such a large volume has been reported using an electronically controllable device. The controllability of this device is demonstrated with a series of ejections where the desired volume is ejected to within 1 % during an injection at a predetermined jet velocity.

Effect of diatrizoate meglumine (Hypaque) on the perilymphatic oxygen tension.

PubMed

Nagahara, K; Fisch, U

1982-12-01

The effect of diatrizoate meglumine (Hypaque) upon the perilymphatic oxygenation has been investigated using the polarographic method in cats submitted to various conditions such as normoxia, apnea, hypercapnia and chronically reduced vascularization. The minimal changes of the perilymphatic PO2 recorded after the injection of Hypaque permit to conclude that this drug has no practical effect upon the oxygenation of the perilymph.

47 CFR 1.2003 - Applications affected.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Wireless Telecommunications Bureau Application for Assignment of Authorization and Transfer of Control; FCC... for Consent to Transfer of Control of Corporation Holding Broadcast Station Construction Permit or... License or Transfer of Control of Corporation Holding Radio Broadcast Station Construction Permit or...

Control of fire blight (Erwinia amylovora) on apple trees with trunk-injected plant resistance inducers and antibiotics and assessment of induction of pathogenesis-related protein genes

PubMed Central

Aćimović, Srđan G.; Zeng, Quan; McGhee, Gayle C.; Sundin, George W.; Wise, John C.

2015-01-01

Management of fire blight is complicated by limitations on use of antibiotics in agriculture, antibiotic resistance development, and limited efficacy of alternative control agents. Even though successful in control, preventive antibiotic sprays also affect non-target bacteria, aiding the selection for resistance which could ultimately be transferred to the pathogen Erwinia amylovora. Trunk injection is a target-precise pesticide delivery method that utilizes tree xylem to distribute injected compounds. Trunk injection could decrease antibiotic usage in the open environment and increase the effectiveness of compounds in fire blight control. In field experiments, after 1–2 apple tree injections of either streptomycin, potassium phosphites (PH), or acibenzolar-S-methyl (ASM), significant reduction of blossom and shoot blight symptoms was observed compared to water injected control trees. Overall disease suppression with streptomycin was lower than typically observed following spray applications to flowers. Trunk injection of oxytetracycline resulted in excellent control of shoot blight severity, suggesting that injection is a superior delivery method for this antibiotic. Injection of both ASM and PH resulted in the significant induction of PR-1, PR-2, and PR-8 protein genes in apple leaves indicating induction of systemic acquired resistance (SAR) under field conditions. The time separating SAR induction and fire blight symptom suppression indicated that various defensive compounds within the SAR response were synthesized and accumulated in the canopy. ASM and PH suppressed fire blight even after cessation of induced gene expression. With the development of injectable formulations and optimization of doses and injection schedules, the injection of protective compounds could serve as an effective option for fire blight control. PMID:25717330

A Fully Implanted Drug Delivery System for Peripheral Nerve Blocks in Behaving Animals

PubMed Central

Pohlmeyer, Eric A.; Jordon, Luke R.; Kim, Peter; Miller, Lee E.

2009-01-01

Inhibiting peripheral nerve function can be useful for many studies of the nervous system or motor control. Accomplishing this in a temporary fashion in animal models by using peripheral nerve blocks permits studies of the immediate effects of the loss, and/or any resulting short-term changes and adaptations in behavior or motor control, while avoiding the complications commonly associated with permanent lesions, such as sores or self-mutilation. We have developed a method of quickly and repeatedly inducing temporary, controlled motor deficits in rhesus macaque monkeys via a chronically implanted drug delivery system. This assembly consists of a nerve cuff and a subdermal injection dome, and has proved effective for delivering local anesthetics directly to peripheral nerves for many months. Using this assembly for median and ulnar nerve blocks routinely resulted in over 80% losses in hand and wrist strength for rhesus monkeys. The assembly was also effective for inducing ambulatory motor deficits in rabbits through blocks of the sciatic nerve. Interestingly, while standard anesthetics were sufficient for the rabbit nerve blocks, the inclusion of epinephrine was essential for achieving significant motor blockade in the monkeys. PMID:19524613

30 CFR 905.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., 42 U.S.C. 7401 et seq California Air Pollution Control Laws, Cal. Health & Safety Code section 39000... (11) Noise Control Act, 42 U.S.C. 4903 California Noise Control Act of 1973, Cal. Health & Safety Code... Pollution Control Laws, Cal. Health & Safety Code section 39000 et seq.; the Hazardous Waste Control Law...

Large Advanced Space Systems (LASS) computer-aided design program additions

NASA Technical Reports Server (NTRS)

Farrell, C. E.

1982-01-01

The LSS preliminary and conceptual design requires extensive iteractive analysis because of the effects of structural, thermal, and control intercoupling. A computer aided design program that will permit integrating and interfacing of required large space system (LSS) analyses is discussed. The primary objective of this program is the implementation of modeling techniques and analysis algorithms that permit interactive design and tradeoff studies of LSS concepts. Eight software modules were added to the program. The existing rigid body controls module was modified to include solar pressure effects. The new model generator modules and appendage synthesizer module are integrated (interfaced) to permit interactive definition and generation of LSS concepts. The mass properties module permits interactive specification of discrete masses and their locations. The other modules permit interactive analysis of orbital transfer requirements, antenna primary beam n, and attitude control requirements.

78 FR 72830 - Migratory Bird Permits; Delegating Falconry Permitting Authority to 17 States

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-04

...-0110; FF09M21200-134-FXMB1231099BPP0] RIN 1018-BA01 Migratory Bird Permits; Delegating Falconry... Migratory Bird Permits Program and assigned OMB control number 1018-0022, which expires February 28, 2014... Regulations, as follows: PART 21--MIGRATORY BIRD PERMITS 0 1. The authority citation for part 21 continues to...

47 CFR 73.3500 - Application and report forms.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Wireless Telecommunications Bureau Application for Assignments of Authorization and Transfers of Control... Station Construction Permit or License. 315 Application for Consent to Transfer of Control of Corporation... Broadcast Station Construction Permit or License or Transfer of Control of Corporation Holding Broadcast...

Solid-state non-volatile electronically programmable reversible variable resistance device

NASA Technical Reports Server (NTRS)

Ramesham, Rajeshuni (Inventor); Thakoor, Sarita (Inventor); Daud, Taher (Inventor); Thakoor, Aniklumar P. (Inventor)

1989-01-01

A solid-state variable resistance device (10) whose resistance can be repeatedly altered by a control signal over a wide range, and which will remain stable after the signal is removed, is formed on an insulated layer (14), supported on a substrate (12) and comprises a set of electrodes (16a, 16b) connected by a layer (18) of material, which changes from an insulator to a conductor upon the injection of ions, covered by a layer (22) of material with insulating properties which permit the passage of ions, overlaid by an ion donor material (20). The ion donor material is overlaid by an insulating layer (24) upon which is deposited a control gate (26) located above the contacts. In a preferred embodiment, the variable resistance material comprises WO.sub.3, the ion donor layer comprises Cr.sub.2 O.sub.3, and the layers sandwiching the ion donor layer comprise silicon monoxide. When a voltage is applied to the gate, the resistance between the electrode contacts changes, decreasing with positive voltage and increasing with negative voltage.

40 CFR 270.40 - Transfer of permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 270.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) EPA ADMINISTERED PERMIT PROGRAMS: THE HAZARDOUS WASTE PERMIT PROGRAM Changes to Permit § 270.40... Act. (b) Changes in the ownership or operational control of a facility may be made as a Class 1...

40 CFR 270.40 - Transfer of permits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 270.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) EPA ADMINISTERED PERMIT PROGRAMS: THE HAZARDOUS WASTE PERMIT PROGRAM Changes to Permit § 270.40... Act. (b) Changes in the ownership or operational control of a facility may be made as a Class 1...

21 CFR 1210.24 - Temporary permits.

Code of Federal Regulations, 2011 CFR

2011-04-01

... and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... FEDERAL IMPORT MILK ACT Permit Control § 1210.24 Temporary permits. A temporary permit will be granted... inspections required by the applicable provisions of section 2 of the Federal Import Milk Act. Temporary...

21 CFR 1210.24 - Temporary permits.

Code of Federal Regulations, 2010 CFR

2010-04-01

... and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... FEDERAL IMPORT MILK ACT Permit Control § 1210.24 Temporary permits. A temporary permit will be granted... inspections required by the applicable provisions of section 2 of the Federal Import Milk Act. Temporary...

Potential Air Pollutant Emissions and Permitting Classifications for Two Biorefinery Process Designs in the United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eberle, Annika; Bhatt, Arpit; Zhang, Yimin

Advanced biofuel production facilities (biorefineries), such as those envisioned by the United States (U.S.) Renewable Fuel Standard and U.S. Department of Energy's research and development programs, often lack historical air pollutant emissions data, which can pose challenges for obtaining air emission permits that are required for construction and operation. To help fill this knowledge gap, we perform a thorough regulatory analysis and use engineering process designs to assess the applicability of federal air regulations and quantify air pollutant emissions for two feasibility-level biorefinery designs. We find that without additional emission-control technologies both biorefineries would likely be required to obtain majormore » source permits under the Clean Air Act's New Source Review program. The permitting classification (so-called 'major' or 'minor') has implications for the time and effort required for permitting and therefore affects the cost of capital and the fuel selling price. Consequently, we explore additional technically feasible emission-control technologies and process modifications that have the potential to reduce emissions to achieve a minor source permitting classification. Finally, our analysis of air pollutant emissions and controls can assist biorefinery developers with the air permitting process and inform regulatory agencies about potential permitting pathways for novel biorefinery designs.« less

Potential Air Pollutant Emissions and Permitting Classifications for Two Biorefinery Process Designs in the United States

DOE PAGES

Eberle, Annika; Bhatt, Arpit; Zhang, Yimin; ...

2017-04-26

Advanced biofuel production facilities (biorefineries), such as those envisioned by the United States (U.S.) Renewable Fuel Standard and U.S. Department of Energy's research and development programs, often lack historical air pollutant emissions data, which can pose challenges for obtaining air emission permits that are required for construction and operation. To help fill this knowledge gap, we perform a thorough regulatory analysis and use engineering process designs to assess the applicability of federal air regulations and quantify air pollutant emissions for two feasibility-level biorefinery designs. We find that without additional emission-control technologies both biorefineries would likely be required to obtain majormore » source permits under the Clean Air Act's New Source Review program. The permitting classification (so-called 'major' or 'minor') has implications for the time and effort required for permitting and therefore affects the cost of capital and the fuel selling price. Consequently, we explore additional technically feasible emission-control technologies and process modifications that have the potential to reduce emissions to achieve a minor source permitting classification. Finally, our analysis of air pollutant emissions and controls can assist biorefinery developers with the air permitting process and inform regulatory agencies about potential permitting pathways for novel biorefinery designs.« less

Potential Air Pollutant Emissions and Permitting Classifications for Two Biorefinery Process Designs in the United States.

PubMed

Eberle, Annika; Bhatt, Arpit; Zhang, Yimin; Heath, Garvin

2017-06-06

Advanced biofuel production facilities (biorefineries), such as those envisioned by the United States (U.S.) Renewable Fuel Standard and U.S. Department of Energy's research and development programs, often lack historical air pollutant emissions data, which can pose challenges for obtaining air emission permits that are required for construction and operation. To help fill this knowledge gap, we perform a thorough regulatory analysis and use engineering process designs to assess the applicability of federal air regulations and quantify air pollutant emissions for two feasibility-level biorefinery designs. We find that without additional emission-control technologies both biorefineries would likely be required to obtain major source permits under the Clean Air Act's New Source Review program. The permitting classification (so-called "major" or "minor") has implications for the time and effort required for permitting and therefore affects the cost of capital and the fuel selling price. Consequently, we explore additional technically feasible emission-control technologies and process modifications that have the potential to reduce emissions to achieve a minor source permitting classification. Our analysis of air pollutant emissions and controls can assist biorefinery developers with the air permitting process and inform regulatory agencies about potential permitting pathways for novel biorefinery designs.

NMED Correspondence Related to Notice of Intent for Chromium Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martinez, Ellena Isabel

Two methods of injection using a solution containing 50 kilograms (kg) of tracer are proposed for each well. Half of the tracer (25 kg) may be mixed with 3,000 gallons of potable water and delivered into a scheduled injection stream of treated groundwater as permitted in OP-1835 over a five to seven-hour period. This procedure would then be repeated on a consecutive second day. Alternatively, 5 kg of tracer may be added to each of ten 3,000-gallon tanks for a total of 30,000 gallons of tracer solution that may be injected independently of other injection flow over a period ofmore » up to five days. The permittees request that the types and masses of tracers that may be utilized per each injection well remain flexible enough to allow for one or more of the naphthalene sulfonate tracers to be substituted with a different naphthalene sulfonate. This need for flexibility is due to the availability of the tracers and any tracer listed that is designated for a given CrIN well may be interchanged with a tracer that is designated for another CrIN well, pending final NMED approval. The permittees are not allowed to introduce any new tracers and will submit a final work plan prior to each injection for each CrIN well.« less

Heat transfer to a full-coverage film-cooled surface with 30 degree slant-hole injection

NASA Technical Reports Server (NTRS)

Crawford, M. E.; Kays, W. M.; Moffat, R. J.

1976-01-01

Heat transfer behavior was studied in a turbulent boundary layer with full coverage film cooling through an array of discrete holes and with injection 30 deg to the wall surface in the downstream direction. Stanton numbers were measured for a staggered hole pattern with pitch-to-diameter ratios of 5 and 10, an injection mass flux ratio range of 0.1 to 1.3, and a range of Reynolds number Re sub x of 150,000 to 5 million. Air was used as the working fluid, and the mainstream velocity varied from 9.8 to 34.2 m/sec (32 to 112 ft/sec). The data were taken for secondary injection temperature equal to the wall temperature and also equal to the mainstream temperature. The data may be used to obtain Stanton number as a continuous function of the injectant temperature by use of linear superposition theory. The heat transfer coefficient is defined on the basis of a mainstream-to-wall temperature difference. This definition permits direct comparison of performance between film cooling and transpiration cooling. A differential prediction method was developed to predict the film cooling data base. The method utilizes a two-dimensional boundary layer program with routines to model the injection process and turbulence augmentation. The program marches in the streamwise direction, and when a row of holes is encountered, it stops and injects fluid into the boundary layer. The turbulence level is modeled by algebraically augmenting the mixing length, with the augmentation keyed to a penetration distance for the injected fluid.

Dual fuel injection piggyback controller system

NASA Astrophysics Data System (ADS)

Muji, Siti Zarina Mohd.; Hassanal, Muhammad Amirul Hafeez; Lee, Chua King; Fawzi, Mas; Zulkifli, Fathul Hakim

2017-09-01

Dual-fuel injection is an effort to reduce the dependency on diesel and gasoline fuel. Generally, there are two approaches to implement the dual-fuel injection in car system. The first approach is changing the whole injector of the car engine, the consequence is excessive high cost. Alternatively, it also can be achieved by manipulating the system's control signal especially the Electronic Control Unit (ECU) signal. Hence, the study focuses to develop a dual injection timing controller system that likely adopted to control injection time and quantity of compressed natural gas (CNG) and diesel fuel. In this system, Raspberry Pi 3 reacts as main controller unit to receive ECU signal, analyze it and then manipulate its duty cycle to be fed into the Electronic Driver Unit (EDU). The manipulation has changed the duty cycle to two pulses instead of single pulse. A particular pulse mainly used to control injection of diesel fuel and another pulse controls injection of Compressed Natural Gas (CNG). The test indicated promising results that the system can be implemented in the car as piggyback system. This article, which was originally published online on 14 September 2017, contained an error in the acknowledgment section. The corrected acknowledgment appears in the Corrigendum attached to the pdf.

Closed-Loop Control of Chemical Injection Rate for a Direct Nozzle Injection System.

PubMed

Cai, Xiang; Walgenbach, Martin; Doerpmond, Malte; Schulze Lammers, Peter; Sun, Yurui

2016-01-20

To realize site-specific and variable-rate application of agricultural pesticides, accurately metering and controlling the chemical injection rate is necessary. This study presents a prototype of a direct nozzle injection system (DNIS) by which chemical concentration transport lag was greatly reduced. In this system, a rapid-reacting solenoid valve (RRV) was utilized for injecting chemicals, driven by a pulse-width modulation (PWM) signal at 100 Hz, so with varying pulse width the chemical injection rate could be adjusted. Meanwhile, a closed-loop control strategy, proportional-integral-derivative (PID) method, was applied for metering and stabilizing the chemical injection rate. In order to measure chemical flow rates and input them into the controller as a feedback in real-time, a thermodynamic flowmeter that was independent of chemical viscosity was used. Laboratory tests were conducted to assess the performance of DNIS and PID control strategy. Due to the nonlinear input-output characteristics of the RRV, a two-phase PID control process obtained better effects as compared with single PID control strategy. Test results also indicated that the set-point chemical flow rate could be achieved within less than 4 s, and the output stability was improved compared to the case without control strategy.

40 CFR 146.61 - Applicability

Code of Federal Regulations, 2010 CFR

2010-07-01

... INJECTION CONTROL PROGRAM: CRITERIA AND STANDARDS Criteria and Standards Applicable to Class I Hazardous Waste Injection Wells § 146.61 Applicability (a) This subpart establishes criteria and standards for underground injection control programs to regulate Class I hazardous waste injection wells. Unless otherwise...

Characterization of a high-pressure diesel fuel injection system as a control technology option to improve engine performance and reduce exhaust emissions

NASA Technical Reports Server (NTRS)

Mcfadden, J. J.; Dezelick, R. A.; Barrows, R. R.

1983-01-01

Test results from a high pressure electronically controlled fuel injection system are compared with a commercial mechanical injection system on a single cylinder, diesel test engine using an inlet boost pressure of 2.6:1. The electronic fuel injection system achieved high pressure by means of a fluid intensifier with peak injection pressures of 47 to 69 MPa. Reduced exhaust emissions were demonstrated with an increasing rate of injection followed by a fast cutoff of injection. The reduction in emissions is more responsive to the rate of injection and injection timing than to high peak injection pressure.

40 CFR 49.134 - Rule for forestry and silvicultural burning permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... burning permits. 49.134 Section 49.134 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS... and silvicultural burning permits. (a) What is the purpose of this section? This section establishes a permitting program for forestry and silvicultural burning within the Indian reservation to control emissions...

TRANSMISSION EXPERIMENTS WITH LEUCOSIS OF FOWLS

PubMed Central

Stubbs, E. L.; Furth, J.

1931-01-01

It is shown, in a carefully controlled experiment, that fowl leucemia can be readily transmitted from chicken to chicken by injection. Of 25 fowls, 13 were injected intravenously with blood from a chicken (No. 575) with erythroleucosis and 12 with blood from a chicken (No. 689) with myeloid leucosis. The injected birds and an equal number of uninjected controls were kept in tiers of alternating cages under as nearly identical conditions as possible. The donors, the controls, and the injected birds were all of the same stock and of the same age. In the two series 13 or 52 per cent of the 25 fowls inoculated developed leucemia within 4 to 10 weeks after injection. The two types of leucemia, erythroleucosis and myeloid leucosis, developed in both groups irrespective of the type used for injection. Among the uninjected controls no cases of erythroleucosis or of myeloid leucosis were observed. Lymphoid leucosis occurred in one injected fowl but since it also occurred in one control it may be assumed that it was probably not caused by the injected material. PMID:19869839

21 CFR 1210.26 - Permits for raw milk or cream.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Permits for raw milk or cream. 1210.26 Section... FEDERAL IMPORT MILK ACT Permit Control § 1210.26 Permits for raw milk or cream. Except as provided in § 1210.27, permits to ship or transport raw milk or cream into the United States will be granted only...

21 CFR 1210.26 - Permits for raw milk or cream.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Permits for raw milk or cream. 1210.26 Section... FEDERAL IMPORT MILK ACT Permit Control § 1210.26 Permits for raw milk or cream. Except as provided in § 1210.27, permits to ship or transport raw milk or cream into the United States will be granted only...

Pattern differences in experimental fevers induced by endotoxin, endogenous pyrogen, and prostaglandins.

PubMed

Morimoto, A; Nakamori, T; Watanabe, T; Ono, T; Murakami, N

1988-04-01

To distinguish pattern differences in experimentally induced fevers, we investigated febrile responses induced by intravenous (IV), intracerebroventricular (ICV), and intra-preoptic/anterior hypothalamic (POA) administration of bacterial endotoxin (lipopolysaccharide, LPS), endogenous pyrogen (EP), human recombinant interleukin-1 alpha (IL-1), and prostaglandins E2 and F2 alpha (PGE2 and PGF2 alpha). Intravenous LPS, EP, or IL-1 in high concentrations caused biphasic fever. In low concentrations, they induced only the first phase of fever. Latency to onset and time to first peak of fever induced by IV injection of LPS or EP were almost the same as those after ICV or POA injection of PGE2. Fever induced by ICV or POA administration of LPS, EP, IL-1, or PGF2 alpha had a long latency to onset and a prolonged time course. There were significant differences among the latencies to fever onset exhibited by groups that received ICV or POA injections of LPS, EP, or PGF2 alpha and by groups given IV injections of LPS or EP and ICV or POA injections of PGE2. Present observations indicate different patterns of fever produced by several kinds of pyrogens when given by various routes. These results permit us to consider the possibility that there are several mediators or multiprocesses underlying the pathogenesis of fever.

Jet-noise reduction through liquid-base foam injection.

NASA Technical Reports Server (NTRS)

Manson, L.; Burge, H. L.

1971-01-01

An experimental investigation has been made of the sound-absorbing properties of liquid-base foams and of their ability to reduce jet noise. Protein, detergent, and polymer foaming agents were used in water solutions. A method of foam generation was developed to permit systematic variation of the foam density. The investigation included measurements of sound-absorption coefficents for both plane normal incidence waves and diffuse sound fields. The intrinsic acoustic properties of foam, e.g., the characteristic impedance and the propagation constant, were also determined. The sound emitted by a 1-in.-diam cold nitrogen jet was measured for subsonic (300 m/sec) and supersonic (422 m/sec) jets, with and without foam injection. Noise reductions up to 10 PNdB were measured.

77 FR 72851 - California State Nonroad Engine Pollution Control Standards; Portable Equipment Registration...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-06

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9758-1] California State Nonroad Engine Pollution Control... throughout California without obtaining permits from local air pollution control districts. DATES: Petitions... faced the need to obtain preconstruction and operating permits from different local air pollution...

40 CFR 49.132 - Rule for general open burning permits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Rule for general open burning permits... open burning permits. (a) What is the purpose of this section? This section establishes a permitting program for open burning within the Indian reservation to control emissions of particulate matter and...

21 CFR 1210.20 - Application for permit.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... FEDERAL IMPORT MILK ACT Permit Control § 1210.20 Application for permit. Application for a permit to ship or transport milk or cream into the United States shall be made by the actual shipper upon forms...

21 CFR 1210.20 - Application for permit.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... FEDERAL IMPORT MILK ACT Permit Control § 1210.20 Application for permit. Application for a permit to ship or transport milk or cream into the United States shall be made by the actual shipper upon forms...

40 CFR 49.133 - Rule for agricultural burning permits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Rule for agricultural burning permits... agricultural burning permits. (a) What is the purpose of this section? This section establishes a permitting program for agricultural burning within the Indian reservation to control emissions of particulate matter...

40 CFR 49.133 - Rule for agricultural burning permits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Rule for agricultural burning permits... agricultural burning permits. (a) What is the purpose of this section? This section establishes a permitting program for agricultural burning within the Indian reservation to control emissions of particulate matter...

40 CFR 49.132 - Rule for general open burning permits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Rule for general open burning permits... open burning permits. (a) What is the purpose of this section? This section establishes a permitting program for open burning within the Indian reservation to control emissions of particulate matter and...

40 CFR 49.132 - Rule for general open burning permits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Rule for general open burning permits... open burning permits. (a) What is the purpose of this section? This section establishes a permitting program for open burning within the Indian reservation to control emissions of particulate matter and...

40 CFR 49.132 - Rule for general open burning permits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Rule for general open burning permits... open burning permits. (a) What is the purpose of this section? This section establishes a permitting program for open burning within the Indian reservation to control emissions of particulate matter and...

40 CFR 49.133 - Rule for agricultural burning permits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Rule for agricultural burning permits... agricultural burning permits. (a) What is the purpose of this section? This section establishes a permitting program for agricultural burning within the Indian reservation to control emissions of particulate matter...

40 CFR 49.133 - Rule for agricultural burning permits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Rule for agricultural burning permits... agricultural burning permits. (a) What is the purpose of this section? This section establishes a permitting program for agricultural burning within the Indian reservation to control emissions of particulate matter...

Performance of a Fuel-Injection Spark-Ignition Engine Using a Hydrogenated Safety Fuel

NASA Technical Reports Server (NTRS)

Schey, Oscar W; Young, Alfred W

1934-01-01

This report presents the performance of a single-cylinder test engine using a hydrogenated safety fuel. The safety fuel has a flash point of 125 degrees f. (Cleveland open-dup method), which is high enough to remove most of the fire hazard, and an octane number of 95, which permits higher compression ratios to be used than are permissible with most undoped gasolines.

Relativistic electron beam device

DOEpatents

Freeman, J.R.; Poukey, J.W.; Shope, S.L.; Yonas, G.

1975-07-01

A design is given for an electron beam device for irradiating spherical hydrogen isotope bearing targets. The accelerator, which includes hollow cathodes facing each other, injects an anode plasma between the cathodes and produces an approximately 10 nanosecond, megajoule pulse between the anode plasma and the cathodes. Targets may be repetitively positioned within the plasma between the cathodes, and accelerator diode arrangement permits materials to survive operation in a fusion power source. (auth)

Design for dependability: A simulation-based approach. Ph.D. Thesis, 1993

NASA Technical Reports Server (NTRS)

Goswami, Kumar K.

1994-01-01

This research addresses issues in simulation-based system level dependability analysis of fault-tolerant computer systems. The issues and difficulties of providing a general simulation-based approach for system level analysis are discussed and a methodology that address and tackle these issues is presented. The proposed methodology is designed to permit the study of a wide variety of architectures under various fault conditions. It permits detailed functional modeling of architectural features such as sparing policies, repair schemes, routing algorithms as well as other fault-tolerant mechanisms, and it allows the execution of actual application software. One key benefit of this approach is that the behavior of a system under faults does not have to be pre-defined as it is normally done. Instead, a system can be simulated in detail and injected with faults to determine its failure modes. The thesis describes how object-oriented design is used to incorporate this methodology into a general purpose design and fault injection package called DEPEND. A software model is presented that uses abstractions of application programs to study the behavior and effect of software on hardware faults in the early design stage when actual code is not available. Finally, an acceleration technique that combines hierarchical simulation, time acceleration algorithms and hybrid simulation to reduce simulation time is introduced.

Waterflood control system for maximizing total oil recovery

DOEpatents

Patzek, Tadeusz Wiktor; Silin, Dimitriy Borisovic; De, Asoke Kumar

2005-06-07

A control system and method for determining optimal fluid injection pressure is based upon a model of a growing hydrofracture due to waterflood injection pressure. This model is used to develop a control system optimizing the injection pressure by using a prescribed injection goal coupled with the historical times, pressures, and volume of injected fluid at a single well. In this control method, the historical data is used to derive two major flow components: the transitional component, where cumulative injection volume is scaled as the square root of time, and a steady-state breakthrough component, which scales linearly with respect to time. These components provide diagnostic information and allow for the prevention of rapid fracture growth and associated massive water break through that is an important part of a successful waterflood, thereby extending the life of both injection and associated production wells in waterflood secondary oil recovery operations.

Waterflood control system for maximizing total oil recovery

DOEpatents

Patzek, Tadeusz Wiktor [Oakland, CA; Silin, Dimitriy Borisovich [Pleasant Hill, CA; De, Asoke Kumar [San Jose, CA

2007-07-24

A control system and method for determining optimal fluid injection pressure is based upon a model of a growing hydrofracture due to waterflood injection pressure. This model is used to develop a control system optimizing the injection pressure by using a prescribed injection goal coupled with the historical times, pressures, and volume of injected fluid at a single well. In this control method, the historical data is used to derive two major flow components: the transitional component, where cumulative injection volume is scaled as the square root of time, and a steady-state breakthrough component, which scales linearly with respect to time. These components provide diagnostic information and allow for the prevention of rapid fracture growth and associated massive water break through that is an important part of a successful waterflood, thereby extending the life of both injection and associated production wells in waterflood secondary oil recovery operations.

Towards Attosecond High-Energy Electron Bunches: Controlling Self-Injection in Laser-Wakefield Accelerators Through Plasma-Density Modulation

NASA Astrophysics Data System (ADS)

Tooley, M. P.; Ersfeld, B.; Yoffe, S. R.; Noble, A.; Brunetti, E.; Sheng, Z. M.; Islam, M. R.; Jaroszynski, D. A.

2017-07-01

Self-injection in a laser-plasma wakefield accelerator is usually achieved by increasing the laser intensity until the threshold for injection is exceeded. Alternatively, the velocity of the bubble accelerating structure can be controlled using plasma density ramps, reducing the electron velocity required for injection. We present a model describing self-injection in the short-bunch regime for arbitrary changes in the plasma density. We derive the threshold condition for injection due to a plasma density gradient, which is confirmed using particle-in-cell simulations that demonstrate injection of subfemtosecond bunches. It is shown that the bunch charge, bunch length, and separation of bunches in a bunch train can be controlled by tailoring the plasma density profile.

Closed-Loop Control of Chemical Injection Rate for a Direct Nozzle Injection System

PubMed Central

Cai, Xiang; Walgenbach, Martin; Doerpmond, Malte; Schulze Lammers, Peter; Sun, Yurui

2016-01-01

To realize site-specific and variable-rate application of agricultural pesticides, accurately metering and controlling the chemical injection rate is necessary. This study presents a prototype of a direct nozzle injection system (DNIS) by which chemical concentration transport lag was greatly reduced. In this system, a rapid-reacting solenoid valve (RRV) was utilized for injecting chemicals, driven by a pulse-width modulation (PWM) signal at 100 Hz, so with varying pulse width the chemical injection rate could be adjusted. Meanwhile, a closed-loop control strategy, proportional-integral-derivative (PID) method, was applied for metering and stabilizing the chemical injection rate. In order to measure chemical flow rates and input them into the controller as a feedback in real-time, a thermodynamic flowmeter that was independent of chemical viscosity was used. Laboratory tests were conducted to assess the performance of DNIS and PID control strategy. Due to the nonlinear input–output characteristics of the RRV, a two-phase PID control process obtained better effects as compared with single PID control strategy. Test results also indicated that the set-point chemical flow rate could be achieved within less than 4 s, and the output stability was improved compared to the case without control strategy. PMID:26805833

Maximum Achievable Control Technology Standards in Region 7

EPA Pesticide Factsheets

Maximum Achievable Control Technology Standards (MACTs) are applicable requirements under the Title V operating permit program. This is a resource for permit writers and reviewers to learn about the rules and explore other helpful tools.

Microbial, Physicochemical, and Sensory Characteristics of Quality Grade 2 Beef Enhanced by Injection of Pineapple Concentrate and Honey

PubMed Central

Yoon, Ji Won; Lee, Da Gyeom; Lee, Hyun Jung; Choe, Juhui; Jung, Samooel; Jo, Cheorun

2017-01-01

This study investigated the effect of injecting pineapple concentrate and honey into low marbled beef in order to enhance its sensory qualities, particularly tenderness and flavor, without compromising its fresh appearance. Beef loin was injected with a solution of 6.0% pineapple concentrate, 2.5% honey, 0.5% monosodium L-glutamate, 0.5% phosphate, and 0.3% salt (w/w) to 120% (w/w) of initial meat weight and stored for 14 d. Non-injected beef loin served as a control. Total aerobic bacterial counts, surface meat color, shear force, reducing sugar content, and sensory evaluation of the beef were analyzed at 0.5, 7, and 14 d of storage. Injection did not affect the total aerobic bacterial counts or color of the beef. However, injection increased the stability of meat color, compared with that of the control, during storage. The shear force value was significantly lower in the injected beef than that in the control. The injected beef had a significantly higher reducing sugar content compared with that of the control. In sensory evaluation, tenderness, juiciness, flavor, and overall acceptance of the injected beef were significantly higher than those of the control at 0.5 d. In conclusion, injection of pineapple concentrate and honey can improve the sensory qualities of low marbled beef, during short storage periods, without changing the fresh appearance of the beef. PMID:28943761

27 CFR 1.27 - Change in ownership, management, or control of the applicant.

Code of Federal Regulations, 2010 CFR

2010-04-01

... BOTTLING OF DISTILLED SPIRITS Basic Permits Applications for Permits § 1.27 Change in ownership, management, or control of the applicant. In the event of any change in the ownership, management, or control of..., management, or control of the applicant. 1.27 Section 1.27 Alcohol, Tobacco Products and Firearms ALCOHOL AND...

Injection-controlled laser resonator

DOEpatents

Chang, J.J.

1995-07-18

A new injection-controlled laser resonator incorporates self-filtering and self-imaging characteristics with an efficient injection scheme. A low-divergence laser signal is injected into the resonator, which enables the injection signal to be converted to the desired resonator modes before the main laser pulse starts. This injection technique and resonator design enable the laser cavity to improve the quality of the injection signal through self-filtering before the main laser pulse starts. The self-imaging property of the present resonator reduces the cavity induced diffraction effects and, in turn, improves the laser beam quality. 5 figs.

Injection-controlled laser resonator

DOEpatents

Chang, Jim J.

1995-07-18

A new injection-controlled laser resonator incorporates self-filtering and self-imaging characteristics with an efficient injection scheme. A low-divergence laser signal is injected into the resonator, which enables the injection signal to be converted to the desired resonator modes before the main laser pulse starts. This injection technique and resonator design enable the laser cavity to improve the quality of the injection signal through self-filtering before the main laser pulse starts. The self-imaging property of the present resonator reduces the cavity induced diffraction effects and, in turn, improves the laser beam quality.

30 CFR 933.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2010 CFR

2010-07-01

...); an approval of dam construction (NCGS 143-215.108), an air pollution control permit (NCGS 143-215.26... in a soil conservation district (NCGS 139-9); and compliance with any county ordinance regarding...

40 CFR 437.2 - General definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... local limits by the control authority under 40 CFR § 403.6(c) that apply to the discharge of wastewater subject to this provision. The permit writer (or control authority) will calculate these limitations or... permit writer (or control authority) will develop flow-weighted effluent limitations or standards for the...

40 CFR 52.681 - Permits to construct and tier II operating permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Idaho § 52.681 Permits... Permits issued by the Idaho Department of Environmental Quality in accordance with the Federally-approved State of Idaho Rules for Control of Air Pollution in Idaho, incorporated by reference in section 52.670...

21 CFR 1210.23 - Permits granted on certificates.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Permits granted on certificates. 1210.23 Section 1210.23 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... FEDERAL IMPORT MILK ACT Permit Control § 1210.23 Permits granted on certificates. In the discretion of the...

21 CFR 1210.25 - Permits for pasteurized milk or cream.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Permits for pasteurized milk or cream. 1210.25 Section 1210.25 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... UNDER THE FEDERAL IMPORT MILK ACT Permit Control § 1210.25 Permits for pasteurized milk or cream...

21 CFR 1210.23 - Permits granted on certificates.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Permits granted on certificates. 1210.23 Section 1210.23 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... FEDERAL IMPORT MILK ACT Permit Control § 1210.23 Permits granted on certificates. In the discretion of the...

21 CFR 1210.25 - Permits for pasteurized milk or cream.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Permits for pasteurized milk or cream. 1210.25 Section 1210.25 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... UNDER THE FEDERAL IMPORT MILK ACT Permit Control § 1210.25 Permits for pasteurized milk or cream...

75 FR 42459 - 60-Day Notice of Intention To Request Clearance of Collection of Information; Opportunity for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-21

... Research and Collecting Permit: Application for a Science Education Permit; Investigator's Annual Report... Science Education Permit: 10-741b, Investigator's Annual Report: 10-226. OMB Control Number: 1024-0236... businesses, other scientific parties seeking an NPS research and collecting or science education permit...

Implementing the NPDES program: An update on the WET ...

EPA Pesticide Factsheets

The U.S. EPA has utilized the Clean Water Act - National Pollutant Discharge Elimination System permitting program to protect waters of the U.S for over 40 years. NPDES permit effluent limitations serve as the primary mechanism for controlling discharges of pollutants to receiving waters. When developing effluent limitations for an NPDES permit, a permit writer must consider limits based on both the technology available to control the pollutants (i.e., technology-based effluent limits) and limits that are protective of the water quality standards of the receiving water (i.e., water quality-based effluent limits). WET testing is one of the water quality-based effluent limitation mechanisms available to permit writers that is useful in determining how the additive, synergistic and compounding effects of toxic effluents effect streams. This presentation will provide an overview of the current EPA NPDES permit program direction for increasing the efficacy of NPDES permits program administered by the U.S. EPA and States. The training implementation plan is expected to provide permit writers with a clearer understanding of WET requirements as established via the U.S. EPA WET test manuals, NPDES permitting regulatory authorities, and the WET science which has been long established. not applicable

In Vivo MR Imaging of Pulmonary Perfusion and Gas Exchange in Rats via Continuous Extracorporeal Infusion of Hyperpolarized 129Xe

PubMed Central

Cleveland, Zackary I.; Möller, Harald E.; Hedlund, Laurence W.; Nouls, John C.; Freeman, Matthew S.; Qi, Yi; Driehuys, Bastiaan

2012-01-01

Background Hyperpolarized (HP) 129Xe magnetic resonance imaging (MRI) permits high resolution, regional visualization of pulmonary ventilation. Additionally, its reasonably high solubility (>10%) and large chemical shift range (>200 ppm) in tissues allow HP 129Xe to serve as a regional probe of pulmonary perfusion and gas transport, when introduced directly into the vasculature. In earlier work, vascular delivery was accomplished in rats by first dissolving HP 129Xe in a biologically compatible carrier solution, injecting the solution into the vasculature, and then detecting HP 129Xe as it emerged into the alveolar airspaces. Although easily implemented, this approach was constrained by the tolerable injection volume and the duration of the HP 129Xe signal. Methods and Principal Findings Here, we overcome the volume and temporal constraints imposed by injection, by using hydrophobic, microporous, gas-exchange membranes to directly and continuously infuse 129Xe into the arterial blood of live rats with an extracorporeal (EC) circuit. The resulting gas-phase 129Xe signal is sufficient to generate diffusive gas exchange- and pulmonary perfusion-dependent, 3D MR images with a nominal resolution of 2×2×2 mm3. We also show that the 129Xe signal dynamics during EC infusion are well described by an analytical model that incorporates both mass transport into the blood and longitudinal relaxation. Conclusions Extracorporeal infusion of HP 129Xe enables rapid, 3D MR imaging of rat lungs and, when combined with ventilation imaging, will permit spatially resolved studies of the ventilation-perfusion ratio in small animals. Moreover, EC infusion should allow 129Xe to be delivered elsewhere in the body and make possible functional and molecular imaging approaches that are currently not feasible using inhaled HP 129Xe. PMID:22363613

Effect of ice on pain after corticosteroid injection in the hand and wrist: a randomized controlled trial.

PubMed

An, T W; Boone, S L; Boyer, M I; Gelberman, R H; Osei, D A; Calfee, R P

2016-11-01

This prospective, randomized controlled study was designed to determine if applying ice to the site of corticosteroid injections in the hand and wrist reduces post-injection pain. Patients receiving corticosteroid injections in the hand or wrist at a tertiary institution were enrolled. Subjects were randomized to apply ice to the injection site and take scheduled over-the-counter analgesics ( n = 36) or take scheduled over-the-counter analgesics alone ( n = 32). There were no significant differences in the mean pain score between the two groups at any time-point (pre-injection or 1-5 days post-injection). In regression modelling, the application of ice did not predict pain after injection. Visual analogue pain scores increased at least 2 points (0-10 scale) after injection in 17 out of 36 patients in the ice group versus ten out of 32 control patients. We conclude that the application of ice in addition to over-the-counter analgesics does not reduce post-injection pain after corticosteroid injection in the hand or wrist. I Therapeutic Study.

Best infection control practices for intradermal, subcutaneous, and intramuscular needle injections.

PubMed Central

Hutin, Yvan; Hauri, Anja; Chiarello, Linda; Catlin, Mary; Stilwell, Barbara; Ghebrehiwet, Tesfamicael; Garner, Julia

2003-01-01

OBJECTIVE: To draw up evidence-based guidelines to make injections safer. METHODS: A development group summarized evidence-based best practices for preventing injection-associated infections in resource-limited settings. The development process included a breakdown of the WHO reference definition of a safe injection into a list of potentially critical steps, a review of the literature for each of these steps, the formulation of best practices, and the submission of the draft document to peer review. FINDINGS: Eliminating unnecessary injections is the highest priority in preventing injection-associated infections. However, when intradermal, subcutaneous, or intramuscular injections are medically indicated, best infection control practices include the use of sterile injection equipment, the prevention of contamination of injection equipment and medication, the prevention of needle-stick injuries to the provider, and the prevention of access to used needles. CONCLUSION: The availability of best infection control practices for intradermal, subcutaneous, and intramuscular injections will provide a reference for global efforts to achieve the goal of safe and appropriate use of injections. WHO will revise the best practices five years after initial development, i.e. in 2005. PMID:12973641

Medroxyprogesterone Injection

MedlinePlus

... Medroxyprogesterone injection is a very effective method of birth control but does not prevent the spread of human ... you have been using a different method of birth control and are switching to medroxyprogesterone injection, your doctor ...

Phase IV study of retention on fingolimod versus injectable multiple sclerosis therapies: a randomized clinical trial.

PubMed

Cree, Bruce A C; Arnold, Douglas L; Cascione, Mark; Fox, Edward J; Williams, Ian M; Meng, Xiangyi; Schofield, Lesley; Tenenbaum, Nadia

2018-01-01

In relapsing-remitting multiple sclerosis (RRMS), suboptimal adherence to injectable disease-modifying therapies (iDMTs; interferon β-1a/b, glatiramer acetate) is common, reducing their effectiveness. Patient retention on oral fingolimod and iDMTs was evaluated in PREFER MS , a randomized, parallel-group, active-controlled, open-label, 48-week study. Patients were included if they had RRMS, were aged 18-65 years and had Expanded Disability Status Scale score up to 6, enrolled at 117 US study sites, were treatment naïve or had received only one iDMT class. Patients were randomized 1:1 (fingolimod 0.5 mg/day; preselected iDMT) by interactive voice-and-web-response system without blinding, followed up quarterly, and allowed one study-approved treatment switch after 12 weeks, or earlier for efficacy or safety reasons. The primary outcome was patient retention on randomized treatment over 48 weeks. Secondary endpoints included patient-reported outcomes, brain volume loss (BVL), and cognitive function. Analysis of 433/436 patients receiving fingolimod and 428/439 receiving iDMTs showed that patient retention rate was significantly higher with fingolimod than with iDMTs [352 (81.3%) versus 125 (29.2%); 95% confidence interval 46.4-57.8%; p < 0.0001]. The most common treatment switch was from iDMT to fingolimod for injection-related reasons. Patient satisfaction was greater and BVL less with fingolimod than with iDMTs, with no difference in cognitive function. Adverse events were consistent with established tolerability profiles for each treatment. In RRMS, fingolimod was associated with better treatment retention, patient satisfaction and BVL outcomes than iDMTs. Patients may persist with iDMTs, but many may switch treatment if permitted. Treatment satisfaction fosters adherence, a prerequisite for optimal outcomes.

Invited Review. Combustion instability in spray-guided stratified-charge engines. A review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fansler, Todd D.; Reuss, D. L.; Sick, V.

2015-02-02

Our article reviews systematic research on combustion instabilities (principally rare, random misfires and partial burns) in spray-guided stratified-charge (SGSC) engines operated at part load with highly stratified fuel -air -residual mixtures. Results from high-speed optical imaging diagnostics and numerical simulation provide a conceptual framework and quantify the sensitivity of ignition and flame propagation to strong, cyclically varying temporal and spatial gradients in the flow field and in the fuel -air -residual distribution. For SGSC engines using multi-hole injectors, spark stretching and locally rich ignition are beneficial. Moreover, combustion instability is dominated by convective flow fluctuations that impede motion of themore » spark or flame kernel toward the bulk of the fuel, coupled with low flame speeds due to locally lean mixtures surrounding the kernel. In SGSC engines using outwardly opening piezo-electric injectors, ignition and early flame growth are strongly influenced by the spray's characteristic recirculation vortex. For both injection systems, the spray and the intake/compression-generated flow field influence each other. Factors underlying the benefits of multi-pulse injection are identified. Finally, some unresolved questions include (1) the extent to which piezo-SGSC misfires are caused by failure to form a flame kernel rather than by flame-kernel extinction (as in multi-hole SGSC engines); (2) the relative contributions of partially premixed flame propagation and mixing-controlled combustion under the exceptionally late-injection conditions that permit SGSC operation on E85-like fuels with very low NO x and soot emissions; and (3) the effects of flow-field variability on later combustion, where fuel-air-residual mixing within the piston bowl becomes important.« less

Successful treatment of canine necrolytic migratory erythema (superficial necrolytic dermatitis) due to metastatic glucagonoma with octreotide.

PubMed

Oberkirchner, Ursula; Linder, Keith E; Zadrozny, Leah; Olivry, Thierry

2010-10-01

Necrolytic migratory erythema (NME; also known as superficial necrolytic dermatitis) is a syndrome most often associated with certain chronic liver diseases or pancreatic glucagonomas. In humans with glucagonoma-associated NME, skin lesions usually respond to octreotide, a somatostatin analogue that inhibits glucagon release. In this report an 11-year-old golden retriever dog with pancreatic glucagonoma and metastasis to the regional lymph nodes, spleen and liver was diagnosed with NME. The dog exhibited erosions, ulcers and crusts on the paws, pressure points, muzzle, periocular area and prepuce. The dog was also anorexic and had difficulty walking. Because metastasis precluded surgery, treatment was initiated with subcutaneous octreotide (2 μg/kg twice daily). Skin lesions and systemic clinical signs improved markedly within 5 days. The dosage was increased to nearly 3 μg/kg twice daily and signs almost completely resolved within 10 days. Anorexia was the major adverse effect observed. During the following month, both dosage (1-3.7 μg/kg) and frequency (two to four times daily) of the octreotide injections were adjusted to permit control of clinical signs while maintaining adequate appetite. Temporary cessation of octreotide administration resulted in the rapid recurrence of skin lesions. Resuming injections led to improvement of clinical signs within 48 h. The dog was later euthanized because of progressive metastatic disease. In conclusion, subcutaneous octreotide injections were beneficial in this dog with glucagonoma-associated NME. This somatostatin analogue could be a valuable option to treat canine patients with non-resectable or relapsing pancreatic glucagonoma-associated NME. © 2010 The Authors. Journal compilation © 2010 ESVD and ACVD.

Targeting Apoptosis for Optical Imaging of Infection

PubMed Central

Thakur, Mathew L.; Zhang, Kaijun; Paudyal, Bishnuhari; Devakumar, Devadhas; Covarrubias, Maria Y.; Cheng, Changpo; Gray, Brian D.; Wickstrom, Eric; Pak, Koon Y.

2018-01-01

Purpose Infection is ubiquitous and a major cause of morbidity and mortality. The most reliable method for localizing infection requires radiolabeling autologous white blood cells ex vivo. A compound that can be injected directly into a patient and can selectively image infectious foci will eliminate the drawbacks. The resolution of infection is associated with neutrophil apoptosis and necrosis presenting phosphatidylserine (PS) on the neutrophil outer leaflet. Targeting PS with intravenous administration of a PS-specific, near-infrared (NIR) fluorophore will permit localization of infectious foci by optical imaging. Methods Bacterial infection and sterile inflammation were induced in separate groups (n=5) of mice. PS was targeted with a NIR fluorophore, PSVue®794 (2.7 pmol). Imaging was performed (ex=730 nm, em=830 nm) using Kodak Multispectral FX-Pro system. The contralateral normal thigh served as an individualized control. Confocal microscopy of normal and apoptotic neutrophils and bacteria confirmed PS specificity. Results Lesions, with a 10-s image acquisition, were unequivocally visible at 5 min post-injection. At 3 h post-injection, the lesion to background intensity ratios in the foci of infection (6.6±0.2) were greater than those in inflammation (3.2±0.5). Image fusions confirmed anatomical locations of the lesions. Confocal microscopy determined the fluorophore specificity for PS. Conclusions Targeting PS presented on the outer leaflet of apoptotic or necrotic neutrophils as well as gram-positive microorganism with PS-specific NIR fluorophore provides a sensitive means of imaging infection. Literature indicates that NIR fluorophores can be detected 7-14 cm deep in tissue. This observation together with the excellent results and the continued development of versatile imaging devices could make optical imaging a simple, specific, and rapid modality for imaging infection. PMID:21538153

Automated carbon dioxide digital angiography for lower-limb arterial disease evaluation: safety assessment and comparison with standard iodinated contrast media angiography.

PubMed

Scalise, Filippo; Novelli, Eugenio; Auguadro, Carla; Casali, Valentina; Manfredi, Mariella; Zannoli, Romano

2015-01-01

Carbon dioxide (CO2) has been validated as a contrast agent in a large series of studies. A particular advantages of CO2 over iodinated contrast medium (ICM) is the absence of nephrotoxicity and allergic reactions. One of the limitations of CO2 angiography is the difficulty of CO2 manual injection due to its compressibility. The manual gas injection does not permit optimal control of the gas output. Development of an automated CO2 injector has overcome these problems. This study compares the feasibility, safety, and diagnostic accuracy of automated CO2 digital subtraction angiography (DSA) in comparison with ICM-DSA in the evaluation of critical limb ischemic (CLI) patients. We performed DSA with both CO2 and ICM on 40 consecutive CLI patients and directly compared the two techniques. Sixteen females and 24 males participated in the study (mean age, 71.7 years). We assessed the diagnostic accuracy of CO2 in identifying arterial stenosis in the lower limb, with ICM-DSA used as the gold standard. The overall diagnostic accuracy of CO2-DSA was 96.9% (sensitivity, 99.0%; specificity, 96.1%; positive predictive value, 91.1%; negative predictive value, 99.6%). Tolerable minor symptoms occurred in 3 patients. No allergic reactions or significant decline in renal function were observed in patients receiving the CO2 injection. Carbon dioxide DSA is a valuable and safe alternative to traditional ICM-DSA for evaluating CLI patients. This modality should be considered as the standard choice for CLI patients undergoing angiographic evaluation who are known to have renal insufficiency or contrast allergy.

Active CO2 Reservoir Management: A Strategy for Controlling Pressure, CO2 and Brine Migration in Saline-Formation CCS

NASA Astrophysics Data System (ADS)

Buscheck, T. A.; Sun, Y.; Hao, Y.; Court, B.; Celia, M. A.; Wolery, T.; Tompson, A. F.; Aines, R. D.; Friedmann, J.

2010-12-01

CO2 capture and sequestration (CCS) in deep geological formations is regarded as a promising means of lowering the amount of CO2 emitted to the atmosphere and thereby mitigate global warming. The most promising systems for CCS are depleted oil reservoirs, particularly those suited to CO2-based Enhanced Oil Recovery (CCS-EOR), and deep saline formations, both of which are well separated from the atmosphere. For conventional, industrial-scale, saline-formation CCS, pressure buildup can have a limiting effect on CO2 storage capacity. To address this concern, we analyze Active CO2 Reservoir Management (ACRM), which combines brine extraction and residual-brine reinjection with CO2 injection, comparing it with conventional saline-formation CCS. We investigate the influence of brine extraction on pressure response and CO2 and brine migration using the NUFT code. By extracting brine from the lower portion of the storage formation, from locations progressively further from the center of injection, we can counteract buoyancy that drives CO2 to the top of the formation, which is useful in dipping formations. Using “push-pull” manipulation of the CO2 plume, we expose less of the caprock seal to CO2 and more of the storage formation to CO2, with more of the formation utilized for trapping mechanisms. Plume manipulation can also counteract the influence of heterogeneity. We consider the impact of extraction ratio, defined as net extracted brine volume (extraction minus reinjection) divided by injected CO2 volume. Pressure buildup is reduced with increasing extraction ratio, which reduces CO2 and brine migration, increases CO2 storage capacity, and reduces other risks, such as leakage up abandoned wells, caprock fracturing, fault activation, and induced seismicity. For a 100-yr injection period, a 10-yr delay in brine extraction does not diminish the magnitude of pressure reduction. Moreover, it is possible to achieve pressure management with just a few brine-extraction wells, located far from the injection zone. For an extraction ratio of 1, pressure buildup is minimized, greatly reducing the Area of Review, as well as the area required for securing mineral rights. For an extraction ratio of 1, CO2 and brine migration are unaffected by neighboring CO2 operations, which allows planning, assessing, and conducting of each operation to be carried out independently; thus, permits could be granted on a single-site basis. Brine-extraction wells will be useful during monitoring, providing information for system calibration and history matching. One of several key aspects that ACRM has in common with CCS-EOR is the possibility of generating revenue from the extracted fluids; namely, fresh water produced via brine desalination, using technologies such as Reverse Osmosis. These benefits can offset brine extraction and treatment costs, streamline permitting, and help gain public acceptance. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

50 CFR 622.17 - South Atlantic golden crab controlled access.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the northern zone. Selection will be made from the list of historical participants in the South... vessel by returning an existing permit or permits to the RA with an application for a permit for the...

Epidural migration of new methylene blue in 0.9% sodium chloride solution or 2% mepivacaine solution following injection into the first intercoccygeal space in foal cadavers and anesthetized foals undergoing laparoscopy.

PubMed

Lansdowne, Jennifer L; Kerr, Carolyn L; Bouré, Ludovic P; Pearce, Simon G

2005-08-01

To determine the relationship between epidural cranial migration and injectate volume of an isotonic solution containing dye in laterally recumbent foal cadavers and evaluate the cranial migration and dermatome analgesia of an epidural dye solution during conditions of laparoscopy in foals. 19 foal cadavers and 8 pony foals. Foal cadavers received an epidural injection of dye solution (0.05, 0.1, 0.15, or 0.2 mL/kg) containing 1.2 mg of new methylene blue (NMB)/mL of saline (0.9% NaCl) solution. Length of the dye column and number of intervertebral spaces cranial and caudal to the injection site were measured. Anesthetized foals received an epidural injection of dye solution (0.2 mL/kg) containing saline solution or 2% mepivacaine. Foals were placed in a 100 head-down position, and pneumoperitoneum was induced. Dermatome analgesia was determined by use of a described electrical stimulus technique. Foals were euthanatized, and length of the dye column was measured. Epidural cranial migration of dye solution in foal cadavers increased with increasing volume injected. No significant difference was found in epidural cranial migration of a dye solution (0.2 mL/kg) between anesthetized foals undergoing conditions of laparoscopy and foal cadavers in lateral recumbency. Further craniad migration of the dye column occurred than indicated by dermatome analgesia. Epidural cranial migration increases with volume of injectate. On the basis of dermatome analgesia, an epidural injection of 2% mepivacaine (0.2 mL/kg) alone provides analgesia up to at least the caudal thoracic dermatome and could permit caudal laparoscopic surgical procedures in foals.

Optogenetics through windows on the brain in the nonhuman primate

PubMed Central

Ruiz, Octavio; Lustig, Brian R.; Nassi, Jonathan J.; Cetin, Ali; Reynolds, John H.; Albright, Thomas D.; Callaway, Edward M.; Stoner, Gene R.

2013-01-01

Optogenetics combines optics and genetics to control neuronal activity with cell-type specificity and millisecond temporal precision. Its use in model organisms such as rodents, Drosophila, and Caenorhabditis elegans is now well-established. However, application of this technology in nonhuman primates (NHPs) has been slow to develop. One key challenge has been the delivery of viruses and light to the brain through the thick dura mater of NHPs, which can only be penetrated with large-diameter devices that damage the brain. The opacity of the NHP dura prevents visualization of the underlying cortex, limiting the spatial precision of virus injections, electrophysiological recordings, and photostimulation. Here, we describe a new optogenetics approach in which the native dura is replaced with an optically transparent artificial dura. This artificial dura can be penetrated with fine glass micropipettes, enabling precisely targeted injections of virus into brain tissue with minimal damage to cortex. The expression of optogenetic agents can be monitored visually over time. Most critically, this optical window permits targeted, noninvasive photostimulation and concomitant measurements of neuronal activity via intrinsic signal imaging and electrophysiological recordings. We present results from both anesthetized-paralyzed (optical imaging) and awake-behaving NHPs (electrophysiology). The improvements over current methods made possible by the artificial dura should enable the widespread use of optogenetic tools in NHP research, a key step toward the development of therapies for neuropsychiatric and neurological diseases in humans. PMID:23761700

Linewidth and tuning characteristics of terahertz quantum cascade lasers.

PubMed

Barkan, A; Tittel, F K; Mittleman, D M; Dengler, R; Siegel, P H; Scalari, G; Ajili, L; Faist, J; Beere, H E; Linfield, E H; Davies, A G; Ritchie, D A

2004-03-15

We have measured the spectral linewidths of three continuous-wave quantum cascade lasers operating at terahertz frequencies by heterodyning the free-running quantum cascade laser with two far-infrared gas lasers. Beat notes are detected with a GaAs diode mixer and a microwave spectrum analyzer, permitting very precise frequency measurements and giving instantaneous linewidths of less than -30 kHz. Characteristics are also reported for frequency tuning as the injection current is varied.

JPRS Report, Science & Technology Europe

DTIC Science & Technology

1992-08-12

Head on Chip Industry, Plans [Heinrich von Pierer Interview; Bonn DIE WELT, 15 Jun 92] 33 Swiss Contraves Develops High-Density Multichip Module... Investment costs are low because the method is based on low pressure, 0.1-1.0 MPA, during injection. This permits the use of simpler molds and...For example, ABS Pumpen AG [ABS Pumps German Stock Corporation] in Lohmar needed 1.5 years to define the "Ceramic Compo- nents for Friction

Non-Solenoidal Tokamak Startup via Inboard Local Helicity Injection on the Pegasus ST

NASA Astrophysics Data System (ADS)

Perry, J. M.; Barr, J. L.; Bodner, G. M.; Bongard, M. W.; Fonck, R. J.; Pachicano, J. L.; Reusch, J. A.; Rodriguez Sanchez, C.; Richner, N. J.; Schlossberg, D. J.

2016-10-01

Local helicity injection (LHI) is a non-solenoidal startup technique utilizing small injectors at the plasma edge to source current along helical magnetic field lines. Unstable injected current streams relax to a tokamak-like configuration with high toroidal current multiplication. Flexible placement of injectors permits tradeoffs between helicity injection rate, poloidal field induction, and magnetic geometry requirements for initial relaxation. Experiments using a new set of large-area injectors in the lower divertor explore the efficacy of high-field-side (HFS) injection. The increased area (4 cm2) current source is functional up to full Pegasus toroidal field (BT , inj = 0.23 T). However, relaxation to a tokamak state is increasingly frustrated for BT , inj > 0.15 T with uniform vacuum vertical field. Paths to relaxation at increased field include: manipulation of vacuum poloidal field geometry; increased injector current; and plasma initiation with outboard injectors, subsequently transitioning to divertor injector drive. During initial tests of HFS injectors, achieved Vinj was limited to 600 V by plasma-material interactions on the divertor plate, which may be mitigated by increasing injector elevation. In experiments with helicity injection as the dominant current drive Ip 0.13 MA has been attained, with T̲e > 100 eV and ne 1019 m-3. Extrapolation to full BT, longer pulse length, and Vinj 1 kV suggest Ip > 0.25 MA should be attainable in a plasma dominated by helicity drive. Work supported by US DOE Grant DE-FG02-96ER54375.

Opportunities offered by the interaction of plasma and droplets to elaborate nanostructured oxide materials

NASA Astrophysics Data System (ADS)

Nikravech, Mehrdad; Rahmani, Abdelkader

2016-09-01

The association of plasma and spray will permit to process materials where organometallic precursors are not available or economically non-reliable. The injection of aerosols in low pressure plasma results in the rapid evaporation of solvent and the rapid transformation of small amounts of precursors contained in each droplet leading to form nanoscale oxide particles. We developed two configurations of this technique: one is Spray Plasma that permits to deposit this layers on flat substrates; the second one is Fluidized Spray Plasma that permits to deposit thin layers on the surface of solid beads. The aim of this presentation is to describe the principles of this new technique together with several applications. The influence of experimental parameters to deposit various mixed metal oxides will be demonstrated: thin dense layers of nanostructured ZnO for photovoltaic applications, porous layers of LaxSr1-x MnO3 as the cathode for fuel cells, ZnO-Cu, NiO layers on solid pellets in fluidized bed for catalysis applications. Aknowledgement to Programme interdisciplinaire SPC Énergies de Demain.

Wastewater Disposal Wells, Fracking, and Environmental Injustice in Southern Texas.

PubMed

Johnston, Jill E; Werder, Emily; Sebastian, Daniel

2016-03-01

To investigate race and poverty in areas where oil and gas wastewater disposal wells, which are used to permanently inject wastewater from hydraulic fracturing (fracking) operations, are permitted. With location data of oil and gas disposal wells permitted between 2007 and 2014 in the Eagle Ford area, a region of intensive fracking in southern Texas, we analyzed the racial composition of residents living less than 5 kilometers from a disposal well and those farther away, adjusting for rurality and poverty, using a Poisson regression. The proportion of people of color living less than 5 kilometers from a disposal well was 1.3 times higher than was the proportion of non-Hispanic Whites. Adjusting for rurality, disposal wells were 2.04 times (95% confidence interval = 2.02, 2.06) as common in areas with 80% people of color or more than in majority White areas. Disposal wells are also disproportionately sited in high-poverty areas. Wastewater disposal wells in southern Texas are disproportionately permitted in areas with higher proportions of people of color and residents living in poverty, a pattern known as "environmental injustice."

77 FR 16509 - Proposed Approval of Revision of Five California Clean Air Act Title V Operating Permits Programs

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-21

... Approval of Revision of Five California Clean Air Act Title V Operating Permits Programs AGENCY... the Operating Permits (Title V) programs of the Monterey Bay Unified Air Pollution Control District... been previously subject to Title V for other reasons to obtain a Title V permit. See ``Prevention of...

14 CFR 25.1143 - Engine controls.

Code of Federal Regulations, 2014 CFR

2014-01-01

... means of controlling its engine. (d) For each fluid injection (other than fuel) system and its controls... injection fluid is adequately controlled. (e) If a power or thrust control incorporates a fuel shutoff...

14 CFR 25.1143 - Engine controls.

Code of Federal Regulations, 2013 CFR

2013-01-01

... means of controlling its engine. (d) For each fluid injection (other than fuel) system and its controls... injection fluid is adequately controlled. (e) If a power or thrust control incorporates a fuel shutoff...

75 FR 8732 - Proposed Information Collection; OMB Control Number 1018-0092; Federal Fish and Wildlife Permit...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-25

...] Proposed Information Collection; OMB Control Number 1018-0092; Federal Fish and Wildlife Permit..., contact Hope Grey by mail or e-mail (see ADDRESSES) or by telephone at (703) 358-2482. SUPPLEMENTARY... assigned OMB Control Number 1018-0012. Normal business practices should produce records (e.g., invoices or...

Injectable Polyethylene Glycol Hydrogel for Islet Encapsulation: an in vitro and in vivo Characterization

PubMed Central

Knobeloch, Tracy; Abadi, Sakineh Esmaeili Mohsen; Bruns, Joseph; Zustiak, Silviya Petrova; Kwon, Guim

2017-01-01

An injection of hydrogel-encapsulated islets that controls blood glucose levels over long term would provide a much needed alternative treatment for type 1 diabetes mellitus (T1DM). To this end, we tested the feasibility of using an injectable polyethylene glycol (PEG) hydrogel as a scaffold for islet encapsulation. Encapsulated islets cultured in vitro for 6 days showed excellent cell viability and released insulin with higher basal and stimulated insulin secretion than control islets. Host responses to PEG hydrogels were studied by injecting PEG hydrogels (no treatment and vehicle controls used) into the peritoneal cavities of B6D2F1 mice and monitoring alterations in body weight, food and water intake, and blood glucose levels. After 2 weeks, peritoneal cavity cells were harvested, followed by hydrogel retrieval, and extraction of spleens. Body weights, food and water intake, and blood glucose levels were unaltered in mice injected with hydrogels compared to no treatment and vehicle-injected control mice. Frozen sections of a hydrogel showed the presence of tissues and small number of immune cells surrounding the hydrogel but no cell infiltration into the hydrogel bulk. Spleen sizes were not significantly different under the experimental conditions. Peritoneal cavity cells were slightly higher in mice injected with hydrogels compared to control mice but no statistical difference between vehicle- and hydrogel-injected mice was noted. As an in vivo feasibility study, streptozotocin-induced diabetic mice were injected with vehicle or hydrogels containing 50 islets each into two sites, the peritoneal cavity and a subcutaneous site on the back. Transient control of blood glucose levels were observed in mice injected with hydrogels containing islets. In summary, we developed an injectable PEG hydrogel that supported islet function and survival in vitro and in vivo and elicited only a mild host response. Our work illustrates the feasibility of using injectable PEG hydrogels for islet encapsulation. PMID:29527325

Some Factors Affecting the Reproducibility of Penetration and the Cut-Off of Oil Sprays for Fuel-injection Engines

NASA Technical Reports Server (NTRS)

Beardsley, E G

1928-01-01

This investigation was undertaken at the Langley Memorial Aeronautical Laboratory in connection with a general research on fuel-injection for aircraft. The purpose of the investigation was to determine the factors controlling the reproducibility of spray penetration and secondary discharges after cut-off. The development of single sprays from automatic injection valves was recorded by means of special high-speed photographic apparatus capable of taking 25 consecutive pictures of the moving spray at a rate of 4,000 per second. The effect of two types of injection valves, injection-valve tube length, initial pressure in the injection-valve tube, speed of the injection control mechanism, and time of spray cut-off, on the reproducibility of spray penetration, and on secondary discharges were investigated. It was found that neither type of injection valve materially affected spray reproducibility. The initial pressure in the injection-valve tube controlled the reproducibility of spray penetrations. An increase in the initial pressure or in the length of the injection-valve tube slightly increased the spray penetration within the limits of this investigation. The speed of the injection-control mechanism did not affect the penetration. Analysis of the results indicates that secondary discharges were caused in this apparatus by pressure waves initiated by the rapid opening of the cut-off valve. The secondary discharges were eliminated in this investigation by increasing the length of the injection-valve tube. (author)

Heterogeneity, pore pressure, and injectate chemistry: Control measures for geologic carbon storage

DOE PAGES

Dewers, Thomas; Eichhubl, Peter; Ganis, Ben; ...

2017-11-28

Desirable outcomes for geologic carbon storage include maximizing storage efficiency, preserving injectivity, and avoiding unwanted consequences such as caprock or wellbore leakage or induced seismicity during and post injection. Here, to achieve these outcomes, three control measures are evident including pore pressure, injectate chemistry, and knowledge and prudent use of geologic heterogeneity. Field, experimental, and modeling examples are presented that demonstrate controllable GCS via these three measures. Observed changes in reservoir response accompanying CO 2 injection at the Cranfield (Mississippi, USA) site, along with lab testing, show potential for use of injectate chemistry as a means to alter fracture permeabilitymore » (with concomitant improvements for sweep and storage efficiency). Further control of reservoir sweep attends brine extraction from reservoirs, with benefit for pressure control, mitigation of reservoir and wellbore damage, and water use. State-of-the-art validated models predict the extent of damage and deformation associated with pore pressure hazards in reservoirs, timing and location of networks of fractures, and development of localized leakage pathways. Experimentally validated geomechanics models show where wellbore failure is likely to occur during injection, and efficiency of repair methods. Use of heterogeneity as a control measure includes where best to inject, and where to avoid attempts at storage. Lastly, an example is use of waste zones or leaky seals to both reduce pore pressure hazards and enhance residual CO 2 trapping.« less

Heterogeneity, pore pressure, and injectate chemistry: Control measures for geologic carbon storage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dewers, Thomas; Eichhubl, Peter; Ganis, Ben

Desirable outcomes for geologic carbon storage include maximizing storage efficiency, preserving injectivity, and avoiding unwanted consequences such as caprock or wellbore leakage or induced seismicity during and post injection. Here, to achieve these outcomes, three control measures are evident including pore pressure, injectate chemistry, and knowledge and prudent use of geologic heterogeneity. Field, experimental, and modeling examples are presented that demonstrate controllable GCS via these three measures. Observed changes in reservoir response accompanying CO 2 injection at the Cranfield (Mississippi, USA) site, along with lab testing, show potential for use of injectate chemistry as a means to alter fracture permeabilitymore » (with concomitant improvements for sweep and storage efficiency). Further control of reservoir sweep attends brine extraction from reservoirs, with benefit for pressure control, mitigation of reservoir and wellbore damage, and water use. State-of-the-art validated models predict the extent of damage and deformation associated with pore pressure hazards in reservoirs, timing and location of networks of fractures, and development of localized leakage pathways. Experimentally validated geomechanics models show where wellbore failure is likely to occur during injection, and efficiency of repair methods. Use of heterogeneity as a control measure includes where best to inject, and where to avoid attempts at storage. Lastly, an example is use of waste zones or leaky seals to both reduce pore pressure hazards and enhance residual CO 2 trapping.« less

The Ohio River Valley CO2 Storage Project AEP Mountaineer Plan, West Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neeraj Gupta

2009-01-07

This report includes an evaluation of deep rock formations with the objective of providing practical maps, data, and some of the issues considered for carbon dioxide (CO{sub 2}) storage projects in the Ohio River Valley. Injection and storage of CO{sub 2} into deep rock formations represents a feasible option for reducing greenhouse gas emissions from coal-burning power plants concentrated along the Ohio River Valley area. This study is sponsored by the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL), American Electric Power (AEP), BP, Ohio Coal Development Office, Schlumberger, and Battelle along with its Pacific Northwest Division. Anmore » extensive program of drilling, sampling, and testing of a deep well combined with a seismic survey was used to characterize the local and regional geologic features at AEP's 1300-megawatt (MW) Mountaineer Power Plant. Site characterization information has been used as part of a systematic design feasibility assessment for a first-of-a-kind integrated capture and storage facility at an existing coal-fired power plant in the Ohio River Valley region--an area with a large concentration of power plants and other emission sources. Subsurface characterization data have been used for reservoir simulations and to support the review of the issues relating to injection, monitoring, strategy, risk assessment, and regulatory permitting. The high-sulfur coal samples from the region have been tested in a capture test facility to evaluate and optimize basic design for a small-scale capture system and eventually to prepare a detailed design for a capture, local transport, and injection facility. The Ohio River Valley CO{sub 2} Storage Project was conducted in phases with the ultimate objectives of demonstrating both the technical aspects of CO{sub 2} storage and the testing, logistical, regulatory, and outreach issues related to conducting such a project at a large point source under realistic constraints. The site characterization phase was completed, laying the groundwork for moving the project towards a potential injection phase. Feasibility and design assessment activities included an assessment of the CO{sub 2} source options (a slip-stream capture system or transported CO{sub 2}); development of the injection and monitoring system design; preparation of regulatory permits; and continued stakeholder outreach.« less

Destruction of acid gas emissions

DOEpatents

Mathur, Mahendra P.; Fu, Yuan C.; Ekmann, James M.; Boyle, John M.

1991-01-01

A method of destroying NO.sub.x and SO.sub.2 in a combustion gas in disclosed. The method includes generating active species by treating stable moleucles in a high temperature plasma. Ammonia, methane, steam, hydrogen, nitrogen or a combination of these gases can be selected as the stable molecules. The gases are subjected to plasma conditions sufficient to create free radicals, ions or excited atoms such as N, NH, NH.sub.2, OH.sup.-, CH and/or CH.sub.2. These active species are injected into a combustion gas at a location of sufficiently high temperature to maintain the species in active state and permit them to react with NO.sub.x and SO.sub.2. Typically the injection is made into the immediate post-combustion gases at temperatures of 475.degree.-950.degree. C.

Numerical simulation of a radially injected barium cloud

NASA Technical Reports Server (NTRS)

Swift, D. W.; Wescott, E. M.

1981-01-01

Electrostatic two-dimensional numerical simulations of a radially symmetric barium injection experiment demonstrate that ions created by solar UV irradiation are electrostatically bound to the electrons which remain tied to the field lines on which they are created. Two possible instabilities are identified, but neither of them causes the barium plasma cloud to polarize in a way that would permit the plasma to keep up with the neutrals. In a second model, the velocity of the neutrals is allowed to be a function of the azimuthal angle. Here, a portion of the cloud does polarize in a way that allows a portion of the plasma to detach and move outward at the approximate speed of the neutrals. No rapid detachment is found when only the density of the neutrals is given an azimuthal asymmetry.

Evaluation of trunk injections for control of emerald ash borer

Treesearch

Deborah G. McCullough; Therese M. Poland; David L. Cappaert; Phillip Lewis; John Molongowski

2005-01-01

In 2003, we evaluated trunk injections of imidacloprid for control of emerald ash borer (Agrilus planipennis Fairmaire) (EAB). Results were variable and indicated that efficacy could be affected by injection timing and method and by tree size and vigor. In 2004, we continued studies to assess the optimal timing for imidacloprid trunk injections and...

Models, data available, and data requirements for estimating the effects of injecting saltwater into disposal wells in the greater Altamont-Bluebell oil and gas field, northern Uinta Basin, Utah

USGS Publications Warehouse

Freethey, Geoffrey W.

1988-01-01

Permits for disposing of salty oil-production water have been issued for 19 wells in the Greater Altamont-Bluebell field. During 1986 more than 500 million gallons of production water were injected into the Duchesne River, Uinta, and Green River Formations through 18 of these wells. The physical and chemical effects of injecting this water into aquifers containing potable water are poorly understood. Interfingering and the structural configuration of these formations add complexity to the description of the geometry and hydrogeology of the ground-water system.A preliminary assessment of the problem indicates that numerical modeling may offer a method of determining the effects of injection. Modeling possibilities include variable-density, three-dimensional flow, sectionaltransport, and areal-transport models. Data needed to develop these models can be derived from a synthesis of geologic, hydrologic, and hydrochemical data already available in the files of State and Federal agencies, oil companies, and private companies. Results from each modeling phase would contribute information for implementing the following phase. The result will be a better understanding of how water moves naturally through the groundwater system, the extent of alterations of both vertical and horizontal flow near the disposal wells, and an overall concept of the effects of deep injection on near-surface aquifers.

Application of the SEM to the measurement of solar cell parameters

NASA Technical Reports Server (NTRS)

Weizer, V. G.; Andrews, C. W.

1977-01-01

A pair of techniques are described which make use of the SEM to measure, respectively, the minority carrier diffusion length and the metallurgical junction depth in silicon solar cells. The former technique permits the measurement of the true bulk diffusion length through the application of highly doped field layers to the back surfaces of the cells being investigated. The technique yields an absolute value of the diffusion length from a knowledge of the collected fraction of the injected carriers and the cell thickness. It is shown that the secondary emission contrast observed in the SEM on a reverse-biased diode can depict the location of the metallurgical junction if the diode has been prepared with the proper beveled geometry. The SEM provides the required contrast and the option of high magnification, permitting the measurement of extremely shallow junction depths.

75 FR 50776 - Renewal of Agency Information Collection for Leases and Permits on Trust or Restricted Land...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-17

... (OMB) for renewal. The information collection is currently authorized by OMB Control Number 1076-0155... able to do so. III. Data OMB Control Number: 1076-0155. Title: Leases and Permits, 25 CFR 162. Brief...

75 FR 19421 - Renewal of Agency Information Collection for Leases and Permits on Trust or Restricted Land...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-14

... Control Number 1076-0155, which expires August 31, 2010. DATES: Interested persons are invited to submit... do so. III. Data OMB Control Number: 1076-0155. Title: Leases and Permits, 25 CFR 162. Brief...

Intra-operative periarticular multimodal injection in total knee arthroplasty: a local hospital experience in Hong Kong.

PubMed

Fan, J Ch

2018-04-01

Data from a local report revealed the superior outcome of regional anaesthesia and analgesia compared with general anaesthesia and intravenous patient-controlled analgesia in total knee arthroplasty. This retrospective study aimed to assess the efficacy of intra-operative periarticular multimodal injection in improving postoperative pain and reducing morphine consumption with patient-controlled analgesia after total knee arthroplasty in patients with knee osteoarthritis. From July 2005 to May 2009, 213 total knee arthroplasties without intra-operative periarticular multimodal injection (control group) were performed at a local hospital. From June 2009 to December 2012, 185 total knee arthroplasties were performed with intra-operative periarticular multimodal injection (cocktail group). The inclusion criteria were osteoarthritis of the knee, single method of anaesthesia (general or neuraxial), simple total knee arthroplasty without any metal augmentation or constraint, and postoperative patient-controlled analgesia. Postoperative patient-controlled morphine doses were compared. A total of 152 total knee arthroplasties were recruited to the cocktail group, and 89 to the control group. Duration of tourniquet application and preoperative knee score did not significantly correlate with morphine consumption by patient-controlled analgesia. Multimodal injection significantly decreased such consumption for 36 h. When injection was separately analysed for general and neuraxial anaesthesia, the effect lasted for 42 h and 24 h, respectively. Intra-operative periarticular multimodal injection decreased morphine consumption for up to 42 h postoperatively.

Pure spin current manipulation in antiferromagnetically exchange coupled heterostructures

NASA Astrophysics Data System (ADS)

Avilés-Félix, L.; Butera, A.; González-Chávez, D. E.; Sommer, R. L.; Gómez, J. E.

2018-03-01

We present a model to describe the spin currents generated by ferromagnet/spacer/ferromagnet exchange coupled trilayer systems and heavy metal layers with strong spin-orbit coupling. By exploiting the magnitude of the exchange coupling (oscillatory RKKY-like coupling) and the spin-flop transition in the magnetization process, it has been possible to produce spin currents polarized in arbitrary directions. The spin-flop transition of the trilayer system originates pure spin currents whose polarization vector depends on the exchange field and the magnetization equilibrium angles. We also discuss a protocol to control the polarization sign of the pure spin current injected into the metallic layer by changing the initial conditions of magnetization of the ferromagnetic layers previously to the spin pumping and inverse spin Hall effect experiments. The small differences in the ferromagnetic layers lead to a change in the magnetization vector rotation that permits the control of the sign of the induced voltage components due to the inverse spin Hall effect. Our results can lead to important advances in hybrid spintronic devices with new functionalities, particularly, the ability to control microscopic parameters such as the polarization direction and the sign of the pure spin current through the variation of macroscopic parameters, such as the external magnetic field or the thickness of the spacer in antiferromagnetic exchange coupled systems.

30 CFR 773.25 - Who may challenge ownership or control listings and findings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Who may challenge ownership or control listings... EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS REQUIREMENTS FOR PERMITS AND PERMIT PROCESSING § 773.25 Who may challenge ownership or control listings and findings. You may challenge a listing or finding of ownership or...

Environmental Law Deskbook.

DTIC Science & Technology

1995-11-01

jurisdiction of the Department of the Interior’s Bureau of Land Management (BLM). Flue - Gas Desulfurization (FGD). Post-combustion sulfur dioxide control ...National Pollution Discharge Elimination System Permits .......... 11 VIII Individual Control Strategies for Toxic Pollutants (ICS) ........... 14 IX Storm...individual control strategies be integrated into the sources’ NPDES permits. EPA has established water quality standards for a number of toxic

CO 2 water-alternating-gas injection for enhanced oil recovery: Optimal well controls and half-cycle lengths

DOE PAGES

Chen, Bailian; Reynolds, Albert C.

2018-03-11

We report that CO 2 water-alternating-gas (WAG) injection is an enhanced oil recovery method designed to improve sweep efficiency during CO 2 injection with the injected water to control the mobility of CO 2 and to stabilize the gas front. Optimization of CO 2 -WAG injection is widely regarded as a viable technique for controlling the CO 2 and oil miscible process. Poor recovery from CO 2 -WAG injection can be caused by inappropriately designed WAG parameters. In previous study (Chen and Reynolds, 2016), we proposed an algorithm to optimize the well controls which maximize the life-cycle net-present-value (NPV). However,more » the effect of injection half-cycle lengths for each injector on oil recovery or NPV has not been well investigated. In this paper, an optimization framework based on augmented Lagrangian method and the newly developed stochastic-simplex-approximate-gradient (StoSAG) algorithm is proposed to explore the possibility of simultaneous optimization of the WAG half-cycle lengths together with the well controls. Finally, the proposed framework is demonstrated with three reservoir examples.« less

The efficacy of 95-Hz topical vibration in pain reduction for trigger finger injection: a placebo-controlled, prospective, randomized trial.

PubMed

Park, Kevin W; Boyer, Martin I; Calfee, Ryan P; Goldfarb, Charles A; Osei, Daniel A

2014-11-01

To determine whether vibratory stimulation would decrease pain experienced by patients during corticosteroid injection for trigger finger. A total of 90 trigger finger injections were randomized to 1 of 3 cohorts. With the injection, patients received no vibration (control group), ultrasound vibration (sham control group), or vibration (experimental group). We used a commercial handheld massaging device to provide a vibratory stimulus for the experimental group. We obtained visual analog scale (VAS) pain scores before and after injection to assess anticipated pain and actual pain experienced. Anticipated pain and actual pain did not differ significantly among groups. Anticipated VAS pain scores were 45, 48, and 50 and actual VAS pain scores were 56, 56, and 63 for the vibration, control, and sham control groups, respectively. When normalized using anchoring VAS pain scores for "stubbing a toe" or "paper cut," no between-group differences remained in injection pain scores. Concomitant vibratory stimulation does not reduce pain experienced during corticosteroid injections for trigger finger. Therapeutic I. Copyright © 2014 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

CO 2 water-alternating-gas injection for enhanced oil recovery: Optimal well controls and half-cycle lengths

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Bailian; Reynolds, Albert C.

We report that CO 2 water-alternating-gas (WAG) injection is an enhanced oil recovery method designed to improve sweep efficiency during CO 2 injection with the injected water to control the mobility of CO 2 and to stabilize the gas front. Optimization of CO 2 -WAG injection is widely regarded as a viable technique for controlling the CO 2 and oil miscible process. Poor recovery from CO 2 -WAG injection can be caused by inappropriately designed WAG parameters. In previous study (Chen and Reynolds, 2016), we proposed an algorithm to optimize the well controls which maximize the life-cycle net-present-value (NPV). However,more » the effect of injection half-cycle lengths for each injector on oil recovery or NPV has not been well investigated. In this paper, an optimization framework based on augmented Lagrangian method and the newly developed stochastic-simplex-approximate-gradient (StoSAG) algorithm is proposed to explore the possibility of simultaneous optimization of the WAG half-cycle lengths together with the well controls. Finally, the proposed framework is demonstrated with three reservoir examples.« less

Separation Control in a Multistage Compressor Using Impulsive Surface Injection

NASA Technical Reports Server (NTRS)

Wundrow, David W.; Braunscheidel, Edward P.; Culley, Dennis E.; Bright, Michelle M.

2006-01-01

Control of flow separation using impulsive surface injection is investigated within the multistage environment of a low speed axial-flow compressor. Measured wake profiles behind a set of embedded stator vanes treated with suction-surface injection indicate significant reduction in flow separation at a variety of injection-pulse repetition rates and durations. The corresponding total pressure losses across the vanes reveal a bank of repetition rates at each pulse duration where the separation control remains nearly complete. This persistence allows for demands on the injected-mass delivery system to be economized while still achieving effective flow control. The response of the stator-vane boundary layers to infrequently applied short injection pulses is described in terms of the periodic excitation of turbulent strips whose growth and propagation characteristics dictate the lower bound on the band of optimal pulse repetition rates. The eventual falloff in separation control at higher repetition rates is linked to a competition between the benefits of pulse-induced mixing and the aggravation caused by the periodic introduction of low-momentum fluid. Use of these observations for impulsive actuator design is discussed and their impact on modeling the time-average effect of impulsive surface injection for multistage steady-flow simulation is considered.

Potential superiority of periarticular injection in analgesic effect and early mobilization ability over femoral nerve block following total knee arthroplasty.

PubMed

Fu, Huichao; Wang, Jiaxing; Zhang, Wen; Cheng, Tao; Zhang, Xianlong

2017-01-01

Pain management after total knee arthroplasty (TKA) should permit early knee mobilization with minimal pain. Periarticular injection (PAI) with local anaesthetics has been recently discussed as a protocol of pain control. The purpose of this review of the literature was to evaluate the efficacy of PAI in comparison with femoral nerve block (FNB). A literature search was performed in PubMed, EMBASE, the OVID database and the Cochrane Library databases. Risk of bias was assessed using the Cochrane collaboration tool. Outcomes of interest included narcotic consumption, pain score, early mobilization ability, length of stay and adverse effects or events. Research identified 918 articles, of which six with a total of 284 knees, met the inclusion criteria and were eligible for the current study. Conflicting evidence was found in terms of narcotic consumption on the postoperative day 1 and early mobilization ability. Total narcotic consumption, pain score in the first 2 days after surgery, length of stay and adverse effects or events showed no difference between two groups. Lower pain score on the day of surgery was detected after PAI. When compared to continuous FNB, patients in PAI group showed a tendency to achieving better ability of early mobilization. In consideration of its relatively simple practice and its potential in analgesic effects or early mobilization ability, PAI had superiority to FNB in the management of pain control after TKA. Before PAI could be widely used in clinical practice after TKAs, further investigations would be necessary to confirm or refute our observed results and to unify the protocol of PAI. I.

Pain & resistance in patients with adhesive capsulitis during contrast material injection phase of MR arthrography.

PubMed

Yilmaz, Mehmet Halit; Kantarci, Fatih; Adaletli, Ibrahim; Ulus, Sila; Gulsen, Fatih; Ozer, Harun; Aktas, Ilknur; Akgun, Kenan; Kanberoglu, Kaya

2007-04-01

Adhesive capsulitis of the shoulder is a condition of unknown aetiology that results in the development of restricted active and passive glenohumeral motion. It has been reported that magnetic resonance (MR) imaging is useful in diagnosing adhesive capsulitis. We carried out this study to assess how pain and/or resistance during contrast material injection affects the diagnosis of adhesive capsulitis on magnetic resonance (MR) arthrography. The study included MR arthrography examinations of 21 patients with a diagnosis of adhesive capsulitis. The control group consisted of 20 patients who presented clinically with rotator cuff tear. The pain (visual analog scale, VAS), resistance to injection and the amount of contrast material that could be injected during injection phase of MR arthrography was assessed and compared between groups. The patients in adhesive capsulitis group (mean VAS score 66.5+/-25.5) experienced more pain when compared with the control group (mean VAS score 34.9+/-27.7, P<0.001). A statistically significant difference (P<0.001) in terms of the amount of the injected fluid (4.3+/-2.6 ml for adhesive capsulitis group, and 10.9+/-4.1 ml for control group) was seen into the joint cavity. Resistance to injection was significantly more (P<0.001) in patients with adhesive capsulitis when compared to control group. Experience of pain during injection, a decreased amount of contrast material injected and resistance to injection in patients during injection phase of MR arthrography may suggest adhesive capsulitis.

Active Flow Separation Control of a Stator Vane Using Surface Injection in a Multistage Compressor Experiment

NASA Technical Reports Server (NTRS)

Culley, Dennis E.; Bright, Michelle M.; Prahst, Patricia S.; Strazisar, Anthony J.

2003-01-01

Micro-flow control actuation embedded in a stator vane was used to successfully control separation and improve near stall performance in a multistage compressor rig at NASA Glenn. Using specially designed stator vanes configured with internal actuation to deliver pulsating air through slots along the suction surface, a research study was performed to identify performance benefits using this microflow control approach. Pressure profiles and unsteady pressure measurements along the blade surface and at the shroud provided a dynamic look at the compressor during microflow air injection. These pressure measurements lead to a tracking algorithm to identify the onset of separation. The testing included steady air injection at various slot locations along the vane. The research also examined the benefit of pulsed injection and actively controlled air injection along the stator vane. Two types of actuation schemes were studied, including an embedded actuator for on-blade control. Successful application of an online detection and flow control scheme will be discussed. Testing showed dramatic performance benefit for flow reattachment and subsequent improvement in diffusion through the use of pulsed controlled injection. The paper will discuss the experimental setup, the blade configurations, and preliminary CFD results which guided the slot location along the blade. The paper will also show the pressure profiles and unsteady pressure measurements used to track flow control enhancement, and will conclude with the tracking algorithm for adjusting the control.

Thermally Stratified Compression Ignition: A new advanced low temperature combustion mode with load flexibility

DOE PAGES

Lawler, Benjamin; Splitter, Derek; Szybist, James; ...

2017-03-01

We introduce a new advanced combustion mode, called Thermally Stratified Compression Ignition (TSCI), which uses direct water injection to control both the average temperature and the temperature distribution prior to ignition, thereby providing cycle-to-cycle control over the start and rate of heat release in Low Temperature Combustion (LTC). Experiments were conducted to fundamentally understand the effects of water injection on heat release in LTC. Our results show that water injection retards the start of combustion due to the latent heat of vaporization of the injected water. Furthermore, for start of water injection timings between 20 and 70 degrees before topmore » dead center, combustion is significantly elongated compared to without water injection. The 10–90% burn duration with 6.6 and 9.0 mg of water per cycle was 77% and 146% longer than without water injection, respectively. Forced thermal stratification result from a direct water injection which reduces the heat release rate by local evaporative cooling. Finally, the load limits with and without water injection were determined experimentally. Without water injection, the load range was 2.3–3.6 bar gross IMEP. By using water injection to control heat release, the load range in TSCI was 2.3–8.4 bar gross IMEP, which is a range expansion of over 350%. These results demonstrate that direct water injection can provide significant improvements to both controllability and the range of operability of LTC, thereby resolving the major challenges associated with HCCI.« less

Thermally Stratified Compression Ignition: A new advanced low temperature combustion mode with load flexibility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lawler, Benjamin; Splitter, Derek; Szybist, James

We introduce a new advanced combustion mode, called Thermally Stratified Compression Ignition (TSCI), which uses direct water injection to control both the average temperature and the temperature distribution prior to ignition, thereby providing cycle-to-cycle control over the start and rate of heat release in Low Temperature Combustion (LTC). Experiments were conducted to fundamentally understand the effects of water injection on heat release in LTC. Our results show that water injection retards the start of combustion due to the latent heat of vaporization of the injected water. Furthermore, for start of water injection timings between 20 and 70 degrees before topmore » dead center, combustion is significantly elongated compared to without water injection. The 10–90% burn duration with 6.6 and 9.0 mg of water per cycle was 77% and 146% longer than without water injection, respectively. Forced thermal stratification result from a direct water injection which reduces the heat release rate by local evaporative cooling. Finally, the load limits with and without water injection were determined experimentally. Without water injection, the load range was 2.3–3.6 bar gross IMEP. By using water injection to control heat release, the load range in TSCI was 2.3–8.4 bar gross IMEP, which is a range expansion of over 350%. These results demonstrate that direct water injection can provide significant improvements to both controllability and the range of operability of LTC, thereby resolving the major challenges associated with HCCI.« less

Method of controlling injection of oxygen into hydrogen-rich fuel cell feed stream

DOEpatents

Meltser, Mark Alexander; Gutowski, Stanley; Weisbrod, Kirk

2001-01-01

A method of operating a H.sub.2 --O.sub.2 fuel cell fueled by hydrogen-rich fuel stream containing CO. The CO content is reduced to acceptable levels by injecting oxygen into the fuel gas stream. The amount of oxygen injected is controlled in relation to the CO content of the fuel gas, by a control strategy that involves (a) determining the CO content of the fuel stream at a first injection rate, (b) increasing the O.sub.2 injection rate, (c) determining the CO content of the stream at the higher injection rate, (d) further increasing the O.sub.2 injection rate if the second measured CO content is lower than the first measured CO content or reducing the O.sub.2 injection rate if the second measured CO content is greater than the first measured CO content, and (e) repeating steps a-d as needed to optimize CO consumption and minimize H.sub.2 consumption.

FPGA-based multiprocessor system for injection molding control.

PubMed

Muñoz-Barron, Benigno; Morales-Velazquez, Luis; Romero-Troncoso, Rene J; Rodriguez-Donate, Carlos; Trejo-Hernandez, Miguel; Benitez-Rangel, Juan P; Osornio-Rios, Roque A

2012-10-18

The plastic industry is a very important manufacturing sector and injection molding is a widely used forming method in that industry. The contribution of this work is the development of a strategy to retrofit control of an injection molding machine based on an embedded system microprocessors sensor network on a field programmable gate array (FPGA) device. Six types of embedded processors are included in the system: a smart-sensor processor, a micro fuzzy logic controller, a programmable logic controller, a system manager, an IO processor and a communication processor. Temperature, pressure and position are controlled by the proposed system and experimentation results show its feasibility and robustness. As validation of the present work, a particular sample was successfully injected.

Double-cross hydrostatic pressure sample injection for chip CE: variable sample plug volume and minimum number of electrodes.

PubMed

Luo, Yong; Wu, Dapeng; Zeng, Shaojiang; Gai, Hongwei; Long, Zhicheng; Shen, Zheng; Dai, Zhongpeng; Qin, Jianhua; Lin, Bingcheng

2006-09-01

A novel sample injection method for chip CE was presented. This injection method uses hydrostatic pressure, generated by emptying the sample waste reservoir, for sample loading and electrokinetic force for dispensing. The injection was performed on a double-cross microchip. One cross, created by the sample and separation channels, is used for formation of a sample plug. Another cross, formed by the sample and controlling channels, is used for plug control. By varying the electric field in the controlling channel, the sample plug volume can be linearly adjusted. Hydrostatic pressure takes advantage of its ease of generation on a microfluidic chip, without any electrode or external pressure pump, thus allowing a sample injection with a minimum number of electrodes. The potential of this injection method was demonstrated by a four-separation-channel chip CE system. In this system, parallel sample separation can be achieved with only two electrodes, which is otherwise impossible with conventional injection methods. Hydrostatic pressure maintains the sample composition during the sample loading, allowing the injection to be free of injection bias.

30 CFR 784.20 - Subsidence control plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS UNDERGROUND MINING PERMIT APPLICATIONS-MINIMUM REQUIREMENTS FOR RECLAMATION AND OPERATION PLAN § 784.20... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Subsidence control plan. 784.20 Section 784.20...

California State Implementation Plan; Proposed Approval of Revisions; Northern Sonoma County Air Pollution Control District; Stationary Source Permits

EPA Pesticide Factsheets

EPA is proposing to approve revisions to the Northern Sonoma County Air Pollution Control District (NSCAPCD) portion of the California SIP concerning NSCAPCD's PSD permitting program for new and modified sources of air pollution.

Intra-arterial catheter system to repeatedly deliver mesenchymal stem cells in a rat renal failure model.

PubMed

Katsuoka, Yuichi; Ohta, Hiroki; Fujimoto, Eisuke; Izuhara, Luna; Yokote, Shinya; Kurihara, Sho; Yamanaka, Shuichiro; Tajiri, Susumu; Chikaraish, Tatsuya; Okano, Hirotaka J; Yokoo, Takashi

2016-04-01

Mesenchymal stem cell therapy in renal failure is rarely used because of low rates of cell engraftment after systemic delivery. Repeated intra-arterial cell administration may improve results; however, no current delivery method permits repeated intra-arterial infusions in a rat model. In this study, we developed an intra-arterial delivery system for repeated stem cell infusion via the aorta, catheterizing the left femoral artery to the suprarenal aorta under fluoroscopic guidance in rats with adenosine-induced renal failure. First, we compared our intra-arterial catheter system (C group, n = 3) with tail vein injection (V group, n = 3) for engraftment efficacy, using mesenchymal stem cells from luciferase transgenic rats. Rats were infused with the cells and euthanized the following day; we performed cell-tracking experiments using a bioluminescence imaging system to assess the distribution of the infused cells. Second, we assessed the safety of the system over a 30-day period in a second group of six rats receiving infusions every 7 days. Cells infused through our delivery system efficiently engrafted into the kidney, compared with peripheral venous infusion. In five of the six rats in the safety study, the delivery system remained patent for at least 9 days (range, 9-24 days). Complications became evident only after 10 days. Our intra-arterial catheter system was effective in delivering cells to the kidney and permitted repeated injection of cells.

Chronic cranial window with access port for repeated cellular manipulations, drug application, and electrophysiology

PubMed Central

Roome, Christopher J.; Kuhn, Bernd

2014-01-01

Chronic cranial windows have been instrumental in advancing optical studies in vivo, permitting long-term, high-resolution imaging in various brain regions. However, once a window is attached it is difficult to regain access to the brain under the window for cellular manipulations. Here we describe a simple device that combines long term in vivo optical imaging with direct brain access via glass or quartz pipettes and metal, glass, or quartz electrodes for cellular manipulations like dye or drug injections and electrophysiological stimulations or recordings while keeping the craniotomy sterile. Our device comprises a regular cranial window glass coverslip with a drilled access hole later sealed with biocompatible silicone. This chronic cranial window with access port is cheap, easy to manufacture, can be mounted just as the regular chronic cranial window, and is self-sealing after retraction of the pipette or electrode. We demonstrate that multiple injections can be performed through the silicone port by repetitively bolus loading calcium sensitive dye into mouse barrel cortex and recording spontaneous cellular activity over a period of weeks. As an example to the extent of its utility for electrophysiological recording, we describe how simple removal of the silicone seal can permit patch pipette access for whole-cell patch clamp recordings in vivo. During these chronic experiments we do not observe any infections under the window or impairment of animal health. PMID:25426027

Radiotherapy Improvements by Using Au Nanoparticles.

PubMed

Torrisi, Lorenzo

2015-01-01

Au nanoparticles can be prepared inside biological solutions and incorporated in special molecules for their transport through blood, drugs and proteins up to the tumour sites or directly injected in their volume when it is possible. The Au nanoparticles are biocompatible and can be accepted locally in the organism also at relatively high concentrations. The use of Au nanoparticles injected in the tumour site enhances significantly the effective atomic number of the medium, depending on the used concentration, and consequently the proton and electron energy loss and the X-ray absorption coefficient determining an increment of the local absorbed dose during radiotherapy. Traditional radiotherapy using electrons, X-rays and gamma rays, and innovative protontherapy can benefit the increment of the effective atomic number of the tissue in the presence of Au-nanoparticles embedded in the tumour volume with an adaptive up-take procedure. This method decreases the dose released to the healthy tissues permitting a better cantering of the irradiated targets and shielding the healthy tissue placed behind the tumour. The presented theoretical study approach permits to evaluate an enhancement of the radiotherapy dose of the order of 1 % using 60 MeV protons, of the order of 10% using 6 MeV electrons and of the order of 100 % using 100 keV X-ray photons. Here, we also disccused for patents relaed to the topic.

Low radiation dose in computed tomography: the role of iodine

PubMed Central

Aschoff, Andrik J; Catalano, Carlo; Krix, Martin; Albrecht, Thomas

2017-01-01

Recent approaches to reducing radiation exposure during CT examinations typically utilize automated dose modulation strategies on the basis of lower tube voltage combined with iterative reconstruction and other dose-saving techniques. Less clearly appreciated is the potentially substantial role that iodinated contrast media (CM) can play in low-radiation-dose CT examinations. Herein we discuss the role of iodinated CM in low-radiation-dose examinations and describe approaches for the optimization of CM administration protocols to further reduce radiation dose and/or CM dose while maintaining image quality for accurate diagnosis. Similar to the higher iodine attenuation obtained at low-tube-voltage settings, high-iodine-signal protocols may permit radiation dose reduction by permitting a lowering of mAs while maintaining the signal-to-noise ratio. This is particularly feasible in first pass examinations where high iodine signal can be achieved by injecting iodine more rapidly. The combination of low kV and IR can also be used to reduce the iodine dose. Here, in optimum contrast injection protocols, the volume of CM administered rather than the iodine concentration should be reduced, since with high-iodine-concentration CM further reductions of iodine dose are achievable for modern first pass examinations. Moreover, higher concentrations of CM more readily allow reductions of both flow rate and volume, thereby improving the tolerability of contrast administration. PMID:28471242

[Experimental intervention study of safe injection in basic-level hospitals in Hunan by medical staff].

PubMed

Li, Li; Li, Yinglan; Long, Yanfang; Zhou, Yang; Lu, Jingmei; Wu, Ying

2013-07-01

To experimentally intervene safe injection by medical staff in basic-level hospitals and observe the recent and long-term effect after the intervention and to provide practical measures to improve safe injection. We used random sampling methods to set up groups in county hospitals and township hospitals of Hunan Province, and offered lectures, delivered safe injection guide, brochure and on-site guidance in the experimental group. We surveyed the 2 groups after the intervention at 1 month and 6 months to compare the effect of unsafe injection behaviors and safe injection behaviors. One month after the intervention, the unsafe injection rate in the experimental group decreased from 27.8% to 21.7%, while in the control group injection the unsafe injection rate rose from 26.0% to 27.9%, with significant difference (P<0.01). Six months after the intervention, the unsafe injection rate in the experimental group declined to 18.4% while the unsafe injection rate in the control group also dropped to 22.4%, with significant difference (P<0.01). Unsafe injection rate was decreased in the experimental group at different intervention points, with significant difference (P<0.01). The safe injection behavior scores in the experimental group were higher than those in the control group after the intervention of 1 month and 6 month intervention (P<0.01); the experimental group got higher scores after the intervention (P<0.01). Training of safe injection, distribution of safe injection guide, and comprehensive intervention model can significantly change the primary care practitioners' behaviors in unsafe injections and it is worth promoting.

14 CFR 29.1143 - Engine controls.

Code of Federal Regulations, 2014 CFR

2014-01-01

... means of controlling its engine. (d) Each fluid injection control other than fuel system control must be in the corresponding power control. However, the injection system pump may have a separate control. (e) If a power control incorporates a fuel shutoff feature, the control must have a means to prevent...

14 CFR 29.1143 - Engine controls.

Code of Federal Regulations, 2013 CFR

2013-01-01

... means of controlling its engine. (d) Each fluid injection control other than fuel system control must be in the corresponding power control. However, the injection system pump may have a separate control. (e) If a power control incorporates a fuel shutoff feature, the control must have a means to prevent...

14 CFR 29.1143 - Engine controls.

Code of Federal Regulations, 2011 CFR

2011-01-01

... means of controlling its engine. (d) Each fluid injection control other than fuel system control must be in the corresponding power control. However, the injection system pump may have a separate control. (e) If a power control incorporates a fuel shutoff feature, the control must have a means to prevent...

14 CFR 29.1143 - Engine controls.

Code of Federal Regulations, 2012 CFR

2012-01-01

... means of controlling its engine. (d) Each fluid injection control other than fuel system control must be in the corresponding power control. However, the injection system pump may have a separate control. (e) If a power control incorporates a fuel shutoff feature, the control must have a means to prevent...

An intercomparison of carbon monoxide, nitric oxide, and hydroxyl measurement techniques - Overview of results

NASA Technical Reports Server (NTRS)

Hoell, J. M.; Gregory, G. L.; Carroll, M. A.; Mcfarland, M.; Ridley, B. A.; Davis, D. D.; Bradshaw, J.; Rodgers, M. O.; Torres, A. L.; Condon, E. P.

1984-01-01

Results from an intercomparison of methods to measure carbon monoxide (CO), nitric oxide (NO), and the hydroxyl radical (OH) are discussed. The intercomparison was conducted at Wallops Island, Virginia, in July 1983 and included a laser differential absorption and three grab sample/gas chromatograph methods for CO, a laser-induced fluorescence (LIF) and two chemiluminescence methods for NO, and two LIF methods and a radiocarbon tracer method for OH. The intercomparison was conducted as a field measurement program involving ambient measurements of CO (150-300 ppbv) and NO (10-180 pptv) from a common manifold with controlled injection of CO in incremental steps from 20 to 500 ppbv and NO in steps from 10 to 220 pptv. Only ambient measurements of OH were made. The agreement between the techniques was on the order of 14 percent for CO and 17 percent for NO. Hardware difficulties during the OH tests resulted in a data base with insufficient data and uncertanties too large to permit a meaningful intercomposition.

Real-time bioluminescence imaging of macroencapsulated fibroblasts reveals allograft protection in rhesus monkeys (Macaca mulatta).

PubMed

Tarantal, Alice F; Lee, C Chang I; Itkin-Ansari, Pamela

2009-07-15

Encapsulation of cells has the potential to eliminate the need for immunosuppression for cellular transplantation. Recently, the TheraCyte device was shown to provide long-term immunoprotection of murine islets in a mouse model of diabetes. In this report, translational studies were undertaken using skin fibroblasts from an unrelated rhesus monkey donor that were transduced with an HIV-1-derived lentiviral vector expressing firefly luciferase permitting the use of bioluminescence imaging (BLI) to monitor cell survival over time and in a noninvasive manner. Encapsulated cells were transplanted subcutaneously (n=2), or cells were injected without encapsulation (n=1) and outcomes compared. BLI was performed to monitor cell survival. The BLI signal from the encapsulated cells remained robust postinsertion and in one animal persisted for up to 1 year. In contrast, the control animal that received unencapsulated cells exhibited a complete loss of cell signal within 14 days. These data demonstrate that TheraCyte encapsulation of allogeneic cells provides robust immune protection in transplanted rhesus monkeys.

Capillary test specimen, system, and methods for in-situ visualization of capillary flow and fillet formation

DOEpatents

Hall, Aaron C.; Hosking, F. Michael ,; Reece, Mark

2003-06-24

A capillary test specimen, method, and system for visualizing and quantifying capillary flow of liquids under realistic conditions, including polymer underfilling, injection molding, soldering, brazing, and casting. The capillary test specimen simulates complex joint geometries and has an open cross-section to permit easy visual access from the side. A high-speed, high-magnification camera system records the location and shape of the moving liquid front in real-time, in-situ as it flows out of a source cavity, through an open capillary channel between two surfaces having a controlled capillary gap, and into an open fillet cavity, where it subsequently forms a fillet on free surfaces that have been configured to simulate realistic joint geometries. Electric resistance heating rapidly heats the test specimen, without using a furnace. Image-processing software analyzes the recorded images and calculates the velocity of the moving liquid front, fillet contact angles, and shape of the fillet's meniscus, among other parameters.

In vivo self-bio-imaging of tumors through in situ biosynthesized fluorescent gold nanoclusters

NASA Astrophysics Data System (ADS)

Wang, Jianling; Zhang, Gen; Li, Qiwei; Jiang, Hui; Liu, Chongyang; Amatore, Christian; Wang, Xuemei

2013-01-01

Fluorescence imaging in vivo allows non-invasive tumor diagnostic thus permitting a direct monitoring of cancer therapies progresses. It is established herein that fluorescent gold nanoclusters are spontaneously biosynthesized by cancerous cell (i.e., HepG2, human hepatocarcinoma cell line; K562, leukemia cell line) incubated with micromolar chloroauric acid solutions, a biocompatible molecular Au(III) species. Gold nanoparticles form by Au(III) reduction inside cells cytoplasms and ultimately concentrate around their nucleoli, thus affording precise cell imaging. Importantly, this does not occur in non-cancerous cells, as evidenced with human embryo liver cells (L02) used as controls. This dichotomy is exploited for a new strategy for in vivo self-bio-imaging of tumors. Subcutaneous injections of millimolar chloroauric acid solution near xenograft tumors of the nude mouse model of hepatocellular carcinoma or chronic myeloid leukemia led to efficient biosynthesis of fluorescent gold nanoclusters without significant dissemination to the surrounding normal tissues, hence allowing specific fluorescent self-bio-marking of the tumors.

Rewritable ghost floating gates by tunnelling triboelectrification for two-dimensional electronics

PubMed Central

Kim, Seongsu; Kim, Tae Yun; Lee, Kang Hyuck; Kim, Tae-Ho; Cimini, Francesco Arturo; Kim, Sung Kyun; Hinchet, Ronan; Kim, Sang-Woo; Falconi, Christian

2017-01-01

Gates can electrostatically control charges inside two-dimensional materials. However, integrating independent gates typically requires depositing and patterning suitable insulators and conductors. Moreover, after manufacturing, gates are unchangeable. Here we introduce tunnelling triboelectrification for localizing electric charges in very close proximity of two-dimensional materials. As representative materials, we use chemical vapour deposition graphene deposited on a SiO2/Si substrate. The triboelectric charges, generated by friction with a Pt-coated atomic force microscope tip and injected through defects, are trapped at the air–SiO2 interface underneath graphene and act as ghost floating gates. Tunnelling triboelectrification uniquely permits to create, modify and destroy p and n regions at will with the spatial resolution of atomic force microscopes. As a proof of concept, we draw rewritable p/n+ and p/p+ junctions with resolutions as small as 200 nm. Our results open the way to time-variant two-dimensional electronics where conductors, p and n regions can be defined on demand. PMID:28649986

Propulsion requirements for communications satellites.

NASA Technical Reports Server (NTRS)

Isley, W. C.; Duck, K. I.

1972-01-01

The concept of characteristics thrust is introduced herein as a means of classifying propulsion system tasks related particularly to geosynchronous communications spacecraft. Approximate analytical models are developed to permit estimation of characteristic thrust for injection error corrections, orbit angle re-location, north-south station keeping, east-west station keeping, spin axis precession control, attitude rate damping, and orbit raising applications. Performance assessment factors are then outlined in terms of characteristic power, characteristic weight, and characteristic volume envelope, which are related to the characteristic thrust. Finally, selected performance curves are shown for power as a function of spacecraft weight, including the influence of duty cycle on north-south station keeping, a 90 degree orbit angle re-location in 14 days, and finally comparison of orbit raising tasks from low and intermediate orbits to a final geosynchronous station. Power requirements range from less than 75 watts for north-south station keeping on small payloads up to greater than 15 KW for a 180 day orbit raising mission including a 28.5 degree plane change.

Rewritable ghost floating gates by tunnelling triboelectrification for two-dimensional electronics

NASA Astrophysics Data System (ADS)

Kim, Seongsu; Kim, Tae Yun; Lee, Kang Hyuck; Kim, Tae-Ho; Cimini, Francesco Arturo; Kim, Sung Kyun; Hinchet, Ronan; Kim, Sang-Woo; Falconi, Christian

2017-06-01

Gates can electrostatically control charges inside two-dimensional materials. However, integrating independent gates typically requires depositing and patterning suitable insulators and conductors. Moreover, after manufacturing, gates are unchangeable. Here we introduce tunnelling triboelectrification for localizing electric charges in very close proximity of two-dimensional materials. As representative materials, we use chemical vapour deposition graphene deposited on a SiO2/Si substrate. The triboelectric charges, generated by friction with a Pt-coated atomic force microscope tip and injected through defects, are trapped at the air-SiO2 interface underneath graphene and act as ghost floating gates. Tunnelling triboelectrification uniquely permits to create, modify and destroy p and n regions at will with the spatial resolution of atomic force microscopes. As a proof of concept, we draw rewritable p/n+ and p/p+ junctions with resolutions as small as 200 nm. Our results open the way to time-variant two-dimensional electronics where conductors, p and n regions can be defined on demand.

A preliminary report of percutaneous craniofacial osteoplasty in a rat calvarium.

PubMed

Parkes, William J; Greywoode, Jewel; O'Hara, Brian J; Heffelfinger, Ryan N; Krein, Howard

2014-07-01

To evaluate the potential for injectable, permanent bone augmentation by assessing the biocompatability and bioactivity of subperiosteal hydroxylapatite (Radiesse) deposition in a rat model. Randomized controlled animal model. Fourteen adult Sprague Dawley rats were injected in the parietal skull with 0.2 ml of hydroxylapatite (10 animals) or 0.2 ml of a carrier gel control (4 animals), using a subperiosteal injection technique on the right and a subcutaneous injection technique on the left. At 1, 3, and 6 months, three rats (1 negative control, 2 variables) were sacrificed and the calvaria were harvested. At 12 months, the remaining five rats were sacrificed. After each harvest, the specimens were processed and then examined under both light and polarized microscopy for new bone growth at the injection sites. The inflammatory response was limited with both hydroxylapatite and carrier injections. Injectables were still present 12 months after the injection. New bone formation was only observed when the injection was located deep to a disrupted periosteum The odds of new bone formation was 48.949 times higher (95% confidence intervals CI [2.637, 3759.961]; P=0.002) with subperiosteal hydroxylapatite injections compared to all other combinations of injection plane and injectable. This preliminary report of subperiosteal hydroxylapatite (Radiesse) injection in a rat model has verified the biocompatibility of injectable hydroxylapatite at the bony interface and suggests the potential for new bone formation. N/A. © 2013 The American Laryngological, Rhinological and Otological Society, Inc.

Secondary flow and heat transfer control in gas turbine inlet nozzle guide vanes

NASA Astrophysics Data System (ADS)

Burd, Steven Wayne

1998-12-01

Endwall heat transfer is a very serious problem in the inlet nozzle guide vane region of gas turbine engines. To resolve heat transfer concerns and provide the desired thermal protection, modern cooling flows for the vane endwalls tend to be excessive leading to lossy and inefficient designs. Coolant introduction is further complicated by the flow patterns along vane endwall surfaces. They are three-dimensional and dominated by strong, complex secondary flows. To achieve performance goals for next-generation engines, more aerodynamically efficient and advanced cooling concepts, including combustor bleed cooling, must be investigated. To this end, the overall performance characteristics of several combustor bleed flow designs are assessed in this experimental study. In particular, their contributions toward secondary flow control and component cooling are documented. Testing is performed in a large-scale, guide vane simulator comprised of three airfoils encased between one contoured and one flat endwall. Core flow is supplied to this simulator at an inlet chord Reynolds number of 350,000 and turbulence intensity of 9.5%. Combustor bleed cooling flow is injected through the contoured endwall via inclined slots. The slots vary in cross-sectional area, have equivalent slot widths, and are positioned with their leeward edges 10% of the axial chord ahead of the airfoil leading edges. Measurements with hot-wire anemometry characterize the inlet and exit flow fields of the cascade. Total and static pressure measurements document aerodynamic performance. Thermocouple measurements detail thermal fields and permit evaluation of surface adiabatic effectiveness. To elucidate the effects of bleed injection, data are compared to an experiment taken without bleed. The influence of bleed mass flow rate and slot geometry on the aerodynamic losses and thermal protection arc given. This study suggests that such combustor bleed flow cooling offers significant thermal protection without imposing aerodynamic penalties. Such performance is contrary to the performance of present vane cooling schemes. The results of this investigation support designs which incorporate combustor coolant injection upstream of the airfoil leading edges. To complement, a short exploratory study regarding the effects of surface roughness was also performed. Results indicate modified cooling performance and significantly higher aerodynamic losses with rough surfaces.

Effectiveness of conservative interventions including exercise, manual therapy and medical management in adults with shoulder impingement: a systematic review and meta-analysis of RCTs.

PubMed

Steuri, Ruedi; Sattelmayer, Martin; Elsig, Simone; Kolly, Chloé; Tal, Amir; Taeymans, Jan; Hilfiker, Roger

2017-09-01

To investigate the effectiveness of conservative interventions for pain, function and range of motion in adults with shoulder impingement. Systematic review and meta-analysis of randomised trials. Medline, CENTRAL, CINAHL, Embase and PEDro were searched from inception to January 2017. Randomised controlled trials including participants with shoulder impingement and evaluating at least one conservative intervention against sham or other treatments. For pain, exercise was superior to non-exercise control interventions (standardised mean difference (SMD) -0.94, 95% CI -1.69 to -0.19). Specific exercises were superior to generic exercises (SMD -0.65, 95% CI -0.99 to -0.32). Corticosteroid injections were superior to no treatment (SMD -0.65, 95% CI -1.04 to -0.26), and ultrasound guided injections were superior to non-guided injections (SMD -0.51, 95% CI -0.89 to -0.13). Nonsteroidal anti-inflammatory drugs (NSAIDS) had a small to moderate SMD of -0.29 (95% CI -0.53 to -0.05) compared with placebo. Manual therapy was superior to placebo (SMD -0.35, 95% CI -0.69 to -0.01). When combined with exercise, manual therapy was superior to exercise alone, but only at the shortest follow-up (SMD -0.32, 95% CI -0.62 to -0.01). Laser was superior to sham laser (SMD -0.88, 95% CI -1.48 to -0.27). Extracorporeal shockwave therapy (ECSWT) was superior to sham (-0.39, 95% CI -0.78 to -0.01) and tape was superior to sham (-0.64, 95% CI -1.16 to -0.12), with small to moderate SMDs. Although there was only very low quality evidence, exercise should be considered for patients with shoulder impingement symptoms and tape, ECSWT, laser or manual therapy might be added. NSAIDS and corticosteroids are superior to placebo, but it is unclear how these treatments compare to exercise. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

A low-cost gradient system for high-performance liquid chromatography. Quantitation of complex pharmaceutical raw materials.

PubMed

Erni, F; Frei, R W

1976-09-29

A device is described that makes use of an eight-port motor valve to generate step gradients on the low-pressure side of a piston pump with a low dead volume. Such a gradient device with an automatic control unit, which also permits repetition of previous steps, can be built for about half the cost of a gradient system with two pumps. Applications of this gradient unit to the separation of complex mixtures of glycosides and alkaloids are discussed and compared with separations systems using two high-pressure pumps. The gradients that are used on reversed-phase material with solvent mixtures of water and completely miscible organic solvents are suitable for quantitative routine control of pharmaceutical products. The reproducibility of retention data is excellent over several months and, with the use of loop injectors, major components can be determined quantitatively with a reproducibility of better than 2% (relative standard deviation). The step gradient selector valve can also be used as an introduction system for very large sample volumes. Up to 11 can be injected and samples with concentrations of less than 1 ppb can be determined with good reproducibilities.

Effect of pretreatment with antiinflammatory agents on paraquat toxicity in the rat.

PubMed

Reddy, K A; Litov, R E; Omaye, S T

1977-05-01

Aspirin (ASA), indomethacin (IND), hydrocortisone (HYC) or 0.25% agar (control) were administered (p.o.) daily to rats for 5 days. Following drug pretreatments, the activities of cytosolic superoxide dismutase (SOD), glutathione peroxidase (GP) and glutathione reductase (GR) were elevated 30-70%, 5-25% and 8-25%, respectively. In a second experiment, rats pretreated as above were injected (ip) on the 5th day with paraquat (PQ) (29 mg/kg). Rats in each group expired more ethane 2 hours after PQ injection. After 22 hours, expired ethane returned to zero time levels. All control rats died within 48 hours after PQ injection. At the end of 48 hours, rats pretreated with ASA, IND, or HYC demonstrated survival rates of 13%, 31%, and 47%, respectively. PQ injection produces marked elevations of SOD (82%), GP (328%), and GR (36%) in the lungs of PQ-injected controls rats over non-PQ injected controls. Elevation of these enzymes were also noted in drug-treated rats after PQ injection but at values less than PQ-injected controls. Anti-inflammatory drugs were tested in rat liver homogenates for their ability to inhibit thiobarbituric acid (TBA) reactive product formation. Only the addition of HYC resulted in a decrease formation of TBA-reactive products. Thus in vitro studies suggest that the antiinflammatory drugs tested, other than HYC, may have other mechanisms of actions in addition to inhibition of lipid peroxides.

Laser pulse control of ultrafast heterogeneous electron transfer: a computational study.

PubMed

Wang, Luxia; May, Volkhard

2004-10-22

Laser pulse control of the photoinduced 90 fs charge injection from perylene into the conduction band of TiO2 is studied theoretically. The approach accounts for the electronic-ground state of the dye, the first excited state, the ionized state formed after charge injection, and the continuum of the electronic states in the conduction band, all defined vs a single reaction coordinate. To address different control tasks optimal control theory is combined with a full quantum dynamical description of the electron-vibrational motion accompanying the charge injection process. First it is proved in which way the charge injection time can be changed by tailored laser pulses. In a second step a pump-dump scheme from the perylene ground state to the first excited electronic state and back to the ground state is discussed. Because of the strong coupling of the excited perylene state to the band continuum of TiO2 this control task is more suited to an experimental test than the direct control of the charge injection.

40 CFR 123.46 - Individual control strategies.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROGRAM REQUIREMENTS Transfer of Information and Permit Review § 123.46 Individual control strategies. (a) Not later than February 4, 1989, each State shall submit to the Regional Administrator for review... draft permit with an attached schedule (provided the State meets the schedule for issuing the final...

IRay therapy as an adjuvant therapy in newly diagnosed patients with neovascular age-related macular degeneration.

PubMed

Brand, Christopher; Arnoldussen, Mark

2018-04-17

To determine the safety and efficacy at 12 months of follow-up after stereotactic radiotherapy in combination therapy with intravitreal ranibizumab injections in treatment naïve patients with neovascular age-related macular degeneration. Retrospective data analysis in patients who received stereotactic radiotherapy (IRay Therapy) during the induction phase of intravitreal ranibizumab injections and a monotherapy control group. The baseline VA in the IRay and control group was 59.87 and 59.12 letters respectively. The real world visual acuity outcomes for the IRay group showed a mean gain of +3.0 letters at 12 months. The historical control group had a mean change of - 0.3 letters. The average number of injections for the IRay group and control group over 12 months was 4.45 and 5.64, respectively with three loading injections. Excluding the loading phase, the difference over 12 months was a 45.2% reduction in injections (P < 0.001). The number of subjects in the IRay group that didn't require further injections following the loading phase was 45.5 vs. 24.0% control group (P = 0.005). The difference in mean change in central macular thickness from baseline is significant at 6 (P = 0.010) and 12 months (P < 0.01). There were no safety concerns with the IRay therapy group. Stereotactic radiotherapy in the induction phase of intravitreal injections of ranibizumab for treatment naïve patients with neovascular age-related macular degeneration, resulted in improved visual outcome, statistically fewer injections and statistically drier macular at 12 months, compared to historical controls treated with monotherapy intravitreal ranibizumab injections.

Blood Glucose Levels in Diabetic Patients Following Corticosteroid Injections into the Subacromial Space of the Shoulder.

PubMed

Aleem, Alexander W; Syed, Usman Ali M; Nicholson, Thema; Getz, Charles L; Namdari, Surena; Beredjiklian, Pedro K; Abboud, Joseph A

2017-09-01

Corticosteroid injections are used to treat a variety of orthopedic conditions with the goal of decreasing pain and inflammation. Administration of systemic or local corticosteroids risks temporarily increasing blood glucose levels, especially diabetic patients. The purpose of this study is to quantify the effects of corticosteroid injections on blood glucose levels in diabetic patients with shoulder pathology. Diabetic patients who regularly monitored their blood glucose levels and were indicated for a subacromial corticosteroid injection were included in this prospective investigation. The typical normal morning fasting glucose and most recent hemoglobin A1c level was recorded for each patient. After injection, patients were contacted daily to confirm their fasting morning glucose level for 10 days post-injection. Seventeen consecutive patients were enrolled. Patients with hemoglobin A1c of <7% had an average rise in blood glucose of 38 mg/dL compared to 98 mg/dL in the poorly controlled group after injection ( P <0.001). Well-controlled patients' glucose levels returned to near baseline levels around post-injection day 8, while poorly controlled patients levels remained elevated. Similarly, insulin-dependent diabetic patients had an average increase in fasting glucose level of 99 mg/dL versus 50 mg/dL in non-insulin-dependent diabetic patients ( P <0.001). After corticosteroid injection, patients with well-controlled diabetes experience smaller elevations and faster return to baseline glucose levels than patients with poor control. Insulin dependent diabetics experienced similar findings as patients with poor control. Future studies are needed to evaluate dosing to optimize the risks of blood glucose elevation while maintaining therapeutic benefit.

Method and apparatus for injecting a substance into the bloodstream of a subject

DOEpatents

Lambrecht, Richard M.; Bennett, Gerald W.; Duncan, Charles C.; Ducote, Louis W.

1983-10-18

An apparatus and method for injecting a substance, such as a radiopharmaceutical, into the bloodstream of a subject. The apparatus comprises an injection means, such as a servo controlled syringe, a means for measuring the concentration of that substance in the subject's bloodstream, and means for controlling the injection in response to the measurement so that the concentration of the substance follows a predetermined function of time. The apparatus of the subject invention functions to inject a substance into a subject's bloodstream at a rate controlled by an error signal proportional to the difference between the concentration of the substance in the subject's bloodstream and the predetermined function.

Method and apparatus for injecting a substance into the bloodstream of a subject

DOEpatents

Lambrecht, R.M.; Bennett, G.W.; Duncan, C.C.; Ducote, L.W.

1983-10-18

An apparatus and method is disclosed for injecting a substance, such as a radiopharmaceutical, into the bloodstream of a subject. The apparatus comprises an injection means, such as a servo controlled syringe, a means for measuring the concentration of that substance in the subject's bloodstream, and means for controlling the injection in response to the measurement so that the concentration of the substance follows a predetermined function of time. The apparatus of the subject invention functions to inject a substance into a subject's bloodstream at a rate controlled by an error signal proportional to the difference between the concentration of the substance in the subject's bloodstream and the predetermined function. 2 figs.

76 FR 1525 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Revisions to Rules and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-11

... Pollution; Permitting of Grandfathered and Electing Electric Generating Facilities AGENCY: Environmental... permitting procedures for grandfathered electric generating facilities (EGFs). The revisions address a... emissions increases of carbon monoxide (CO) created by the imposition of technology controls to be permitted...

40 CFR 233.36 - Modification, suspension or revocation of permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... has been submitted to the Director; (iv) Provide for minor modification of project plans that do not... appropriately regulated by individual permits; (4) Circumstances relating to the authorized activity have... cessation of any discharge controlled by the permit; (5) Any significant information relating to the...

40 CFR 146.1 - Applicability and scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) UNDERGROUND INJECTION CONTROL PROGRAM: CRITERIA AND STANDARDS General Provisions § 146.1 Applicability and scope. (a) This part sets forth technical criteria and standards for the Underground Injection Control... of a State UIC program by the Administrator, any underground injection which is not authorized by the...

Embedded computer controlled premixing inline injection system for air-assisted variable-rate sprayers

USDA-ARS?s Scientific Manuscript database

Improvements to reduce chemical waste and environmental pollution for variable-rate sprayers used in orchards and ornamental nurseries require inline injection techniques. A microprocessor controlled premixing inline injection system implementing a ceramic piston chemical metering pump and two small...

Effects of music therapy on intravitreal injections: a randomized clinical trial.

PubMed

Chen, Xuejing; Seth, Rajeev K; Rao, Veena S; Huang, John J; Adelman, Ron A

2012-08-01

To investigate the effects of music therapy on anxiety, perceived pain, and satisfaction in patients undergoing intravitreal injections in the outpatient setting. This is a randomized clinical trial. Seventy-three patients were recruited from the retina clinic at 1 institution and randomized into a music therapy (n=37) or control (n=36) group. Prior to injection, patients completed the state portion of the Spielberger State Trait Anxiety Inventory (STAI-S). The music therapy group listened to classical music through computer speakers while waiting for and during the injection. The control group underwent the injection in the same setting without music. Afterward, all patients completed another STAI-S and a satisfaction and pain questionnaire. The main outcome measures were objective anxiety derived from STAI-S scores and subjective pain and anxiety from the post procedure questionnaire. The music therapy group had a greater decrease in anxiety than the control group (P=0.0480). Overall, 73% of all patients requested music for future injections (P=0.0001). The music therapy group (84%) requested music in future injections more frequently than the control group (61%) (P=0.0377). Both groups reported similar levels of pain (P=0.5879). Classical music before and during intravitreal injections decreases anxiety in patients without decreasing pain. Most patients desire to have music during future injections. Music therapy is a low-cost, easy, safe intervention that reduces anxiety during intravitreal injections in the outpatient setting.

FPGA-Based Multiprocessor System for Injection Molding Control

PubMed Central

Muñoz-Barron, Benigno; Morales-Velazquez, Luis; Romero-Troncoso, Rene J.; Rodriguez-Donate, Carlos; Trejo-Hernandez, Miguel; Benitez-Rangel, Juan P.; Osornio-Rios, Roque A.

2012-01-01

The plastic industry is a very important manufacturing sector and injection molding is a widely used forming method in that industry. The contribution of this work is the development of a strategy to retrofit control of an injection molding machine based on an embedded system microprocessors sensor network on a field programmable gate array (FPGA) device. Six types of embedded processors are included in the system: a smart-sensor processor, a micro fuzzy logic controller, a programmable logic controller, a system manager, an IO processor and a communication processor. Temperature, pressure and position are controlled by the proposed system and experimentation results show its feasibility and robustness. As validation of the present work, a particular sample was successfully injected. PMID:23202036

Comparing the effect of An's Shaobei Injection ([symbols; see text]) with Xiaozhiling Injection ([symbols; see text]) in patients with internal hemorrhoids of grade I-III: a prospective cohort study.

PubMed

An, A-yue; Feng, Da-yong; Wang, Chun-hui; Shi, Yu-ying; Xiang, Jing-jing; Bai, Zhi-yong; Li, Kun-cheng; Liu, Jin-yang

2014-07-01

To compare the effect of An's Shaobei Injection ([symbols; see text]) with Xiaozhiling Injection ([symbols; see text]) in patients with internal hemorrhoids of grade I-III. This cohort study included 1,520 internal hemorrhoids patients with grade I-III who were scheduled for liquid injection treatment from July 2003 to July 2009. The cohort included patients who underwent either An's Shaobei Injection treatment (the treatment group, 760 cases) or Xiaozhiling Injection treatment (the control group, 760 cases). All patients were followed up regularly for 3 years; the observing indices included anal function recovery and clinical response after operation. Among the 1,520 patients, 1,508 (99.2%) completed the 3-year follow-up. The efficacy rate was 97.5% in the treatment group, significantly higher than the control group (91.8%, P<0.01). The recurrence rate in the treatment group was 0.5%, significantly lower than that of the control group (1.3%, P<0.01). In addition, perianal callosity occurred in 8 cases (1.1%) and anorectal stricture in 26 cases (3.5%) after operation in the control group. There was no perianal callosity and anorectal stricture in the treatment group. The treatment with An's Shaobei Injection demonstrated superior clinical effect to Xiaozhiling Injection with fewer adverse effects.

Expression of a model gene in prostate cancer cells lentivirally transduced in vitro and in vivo.

PubMed

Bastide, C; Maroc, N; Bladou, F; Hassoun, J; Maitland, N; Mannoni, P; Bagnis, C

2003-01-01

In a preclinical model for prostate cancer gene therapy, we have tested lentiviral vectors as a practical possibility for the transfer and long-term expression of the EGFP gene both in vitro and in vivo. The human prostate cancer cell lines DU145 and PC3 were transduced using experimental conditions which permitted analysis of the expression from a single proviral vector per cell. The transduced cells stably expressed the EGFP transgene for 4 months. After injection of the transduced cell populations into Nod-SCID mice a decrease in EGFP was only observed in a minority of cases, while the majority of tumors maintained transgene expression at in vitro levels. In vivo injection of viral vector preparations directly into pre-established subcutaneous or orthotopic tumor masses, obtained by implantation of untransduced PC3 and DU145 cells led to a high transduction efficiency. While the efficiency of direct intratumoral transduction was proportional to the dose of virus injected, the results indicated some technical limitations inherent in these approaches to prostate cancer gene therapy.

Direct electron injection into an oxide insulator using a cathode buffer layer

PubMed Central

Lee, Eungkyu; Lee, Jinwon; Kim, Ji-Hoon; Lim, Keon-Hee; Seok Byun, Jun; Ko, Jieun; Dong Kim, Young; Park, Yongsup; Kim, Youn Sang

2015-01-01

Injecting charge carriers into the mobile bands of an inorganic oxide insulator (for example, SiO2, HfO2) is a highly complicated task, or even impossible without external energy sources such as photons. This is because oxide insulators exhibit very low electron affinity and high ionization energy levels. Here we show that a ZnO layer acting as a cathode buffer layer permits direct electron injection into the conduction bands of various oxide insulators (for example, SiO2, Ta2O5, HfO2, Al2O3) from a metal cathode. Studies of current–voltage characteristics reveal that the current ohmically passes through the ZnO/oxide-insulator interface. Our findings suggests that the oxide insulators could be used for simply fabricated, transparent and highly stable electronic valves. With this strategy, we demonstrate an electrostatic discharging diode that uses 100-nm SiO2 as an active layer exhibiting an on/off ratio of ∼107, and protects the ZnO thin-film transistors from high electrical stresses. PMID:25864642

Phase noise analysis of a 10-GHz optical injection-locked vertical-cavity surface-emitting laser-based optoelectronic oscillator

NASA Astrophysics Data System (ADS)

Coronel, Juan; Varón, Margarita; Rissons, Angélique

2016-09-01

The optical injection locking (OIL) technique is proposed to reduce the phase noise of a carrier generated for a vertical-cavity surface-emitting laser (VCSEL)-based optoelectronic oscillator. The OIL technique permits the enhancement of the VCSEL direct modulation bandwidth as well as the stabilization of the optical noise of the laser. A 2-km delay line, 10-GHz optical injection-locked VCSEL-based optoelectronic oscillator (OILVBO) was implemented. The internal noise sources of the optoelectronic oscillator components were characterized and analyzed to understand the noise conversion of the system into phase noise in the oscillator carrier. The implemented OILVBO phase noise was -105.7 dBc/Hz at 10 kHz from the carrier; this value agrees well with the performed simulated analysis. From the computed and measured phase noise curves, it is possible to infer the noise processes that take place inside the OILVBO. As a second measurement of the oscillation quality, a time-domain analysis was done through the Allan's standard deviation measurement, reported for first time for an optoelectronic oscillator using the OIL technique.

Parametric Studies of Flow Separation using Air Injection

NASA Technical Reports Server (NTRS)

Zhang, Wei

2004-01-01

Boundary Layer separation causes the airfoil to stall and therefore imposes dramatic performance degradation on the airfoil. In recent years, flow separation control has been one of the active research areas in the field of aerodynamics due to its promising performance improvements on the lifting device. These active flow separation control techniques include steady and unsteady air injection as well as suction on the airfoil surface etc. This paper will be focusing on the steady and unsteady air injection on the airfoil. Although wind tunnel experiments revealed that the performance improvements on the airfoil using injection techniques, the details of how the key variables such as air injection slot geometry and air injection angle etc impact the effectiveness of flow separation control via air injection has not been studied. A parametric study of both steady and unsteady air injection active flow control will be the main objective for this summer. For steady injection, the key variables include the slot geometry, orientation, spacing, air injection velocity as well as the injection angle. For unsteady injection, the injection frequency will also be investigated. Key metrics such as lift coefficient, drag coefficient, total pressure loss and total injection mass will be used to measure the effectiveness of the control technique. A design of experiments using the Box-Behnken Design is set up in order to determine how each of the variables affects each of the key metrics. Design of experiment is used so that the number of experimental runs will be at minimum and still be able to predict which variables are the key contributors to the responses. The experiments will then be conducted in the 1ft by 1ft wind tunnel according to the design of experiment settings. The data obtained from the experiments will be imported into JMP, statistical software, to generate sets of response surface equations which represent the statistical empirical model for each of the metrics as a function of the key variables. Next, the variables such as the slot geometry can be optimized using the build-in optimizer within JMP. Finally, a wind tunnel testing will be conducted using the optimized slot geometry and other key variables to verify the empirical statistical model. The long term goal for this effort is to assess the impacts of active flow control using air injection at system level as one of the task plan included in the NASAs URETI program with Georgia Institute of Technology.

29 CFR 1926.152 - Flammable and combustible liquids.

Code of Federal Regulations, 2010 CFR

2010-07-01

... access way to permit approach of fire control apparatus. (3) The storage area shall be graded in a manner... to permit approach of fire control apparatus. (5) Storage areas shall be kept free of weeds, debris... wooden storage cabinets shall be constructed in the following manner, or equivalent: The bottom, sides...

78 FR 63929 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Revisions to Rules and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-25

... for Control of Air Pollution; Permitting of Grandfathered Facilities AGENCY: Environmental Protection... grandfathered facilities obtain specific permits which include emission control methods to achieve mandated... or contact information unless you provide it in the body of your comment. If you send an email...

9 CFR 94.18 - Restrictions on importation of meat and edible products from ruminants due to bovine spongiform...

Code of Federal Regulations, 2012 CFR

2012-01-01

... DISEASE, EXOTIC NEWCASTLE DISEASE, AFRICAN SWINE FEVER, CLASSICAL SWINE FEVER, SWINE VESICULAR DISEASE... Importation and Transportation of Controlled Materials and Organisms and Vectors by filing a permit... Veterinary Permit for Importation and Transportation of Controlled Materials and Organisms and Vectors by...

9 CFR 94.18 - Restrictions on importation of meat and edible products from ruminants due to bovine spongiform...

Code of Federal Regulations, 2013 CFR

2013-01-01

... DISEASE, EXOTIC NEWCASTLE DISEASE, AFRICAN SWINE FEVER, CLASSICAL SWINE FEVER, SWINE VESICULAR DISEASE... Importation and Transportation of Controlled Materials and Organisms and Vectors by filing a permit... Veterinary Permit for Importation and Transportation of Controlled Materials and Organisms and Vectors by...

76 FR 68385 - Approval and Promulgation of Implementation Plans; New Mexico; Albuquerque/Bernalillo County...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... NMAC) addition of in subsections methodology for (A) and (B). fugitive dust control permits, revised... fee Fee Calculations and requirements for Procedures. fugitive dust control permits. 9/7/2004 Section... schedule based on acreage, add and update calculation methodology used to calculate non- programmatic dust...

29 CFR 1926.152 - Flammable and combustible liquids.

Code of Federal Regulations, 2011 CFR

2011-07-01

... access way to permit approach of fire control apparatus. (3) The storage area shall be graded in a manner... to permit approach of fire control apparatus. (5) Storage areas shall be kept free of weeds, debris... wooden storage cabinets shall be constructed in the following manner, or equivalent: The bottom, sides...

A Model To Estimate Carbon Dioxide Injectivity and Storage Capacity for Geological Sequestration in Shale Gas Wells.

PubMed

Edwards, Ryan W J; Celia, Michael A; Bandilla, Karl W; Doster, Florian; Kanno, Cynthia M

2015-08-04

Recent studies suggest the possibility of CO2 sequestration in depleted shale gas formations, motivated by large storage capacity estimates in these formations. Questions remain regarding the dynamic response and practicality of injection of large amounts of CO2 into shale gas wells. A two-component (CO2 and CH4) model of gas flow in a shale gas formation including adsorption effects provides the basis to investigate the dynamics of CO2 injection. History-matching of gas production data allows for formation parameter estimation. Application to three shale gas-producing regions shows that CO2 can only be injected at low rates into individual wells and that individual well capacity is relatively small, despite significant capacity variation between shale plays. The estimated total capacity of an average Marcellus Shale well in Pennsylvania is 0.5 million metric tonnes (Mt) of CO2, compared with 0.15 Mt in an average Barnett Shale well. Applying the individual well estimates to the total number of existing and permitted planned wells (as of March, 2015) in each play yields a current estimated capacity of 7200-9600 Mt in the Marcellus Shale in Pennsylvania and 2100-3100 Mt in the Barnett Shale.

78 FR 32081 - Airworthiness Directives; Aircraft Industries a.s. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-29

... Injection System WATER INJECTION circuit ON breakter. TCL TQ=min. 60% WATER INJECTION/ON push- Push and hold till amber button. WATER INJECTION signal comes on (on the front control panel) Before throttling back power: WATER INJECTION/OFF push- Push and check amber button. WATER INJECTION signal extinguishes...

Simulation on Effect of Preform Diameter in Injection Stretch Blow Molding

NASA Astrophysics Data System (ADS)

Tan, Z. Q.; Rosli, Nurrina; Oktaviandri, Muchamad

2018-03-01

Polyethylene terephthalate (PET) is the most common material of resin for manufacturing plastic bottle by injection stretch blow molding due to its excellent properties. As various issues of health and environmental hazards due to the PET use have risen, PET bottle manufacture may be improved by minimizing the wall thickness to reduce the PET use. One of the critical qualifications of the manufacturing process which lead to the wall thickness distribution is the initial preform diameter. In this project, we used the ANSYS Polyflow with aim to evaluate the wall thickness distribution of PET bottle for different diameter of initial preform. As a result, only 4 mm preform diameter presented wall thickness below than 1 mm. On the other hand, at least 6 mm preform diameter can permit the wall thickness 1.3 mm i.e. at the shoulder area.

75 FR 64235 - Approval and Promulgation of Air Quality Implementation Plans; Texas; Revisions to Rules and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-19

... Pollution; Permitting of Grandfathered and Electing Electric Generating Facilities AGENCY: Environmental... permitting procedures for grandfathered electric generating facilities (EGFs). The revisions address a... increases of carbon monoxide (CO) created by the imposition of technology controls to be permitted under the...

40 CFR 63.93 - Approval of State requirements that substitute for a section 112 rule.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., board and administrative orders, permits issued pursuant to permit templates, or State operating permits... respective Federal rule; (2) Levels of control (including associated performance test methods) and compliance... must include monitoring or another method for determining compliance. (ii) If a standard in the...

9 CFR 104.3 - Permit application.

Code of Federal Regulations, 2010 CFR

2010-01-01

... VIRUSES, SERUMS, TOXINS, AND ANALOGOUS PRODUCTS; ORGANISMS AND VECTORS PERMITS FOR BIOLOGICAL PRODUCTS § 104.3 Permit application. (a) Each person desiring to import a biological product shall make written... control number 0579-0013) [38 FR 32916, Nov. 29, 1973, as amended at 48 FR 57473, Dec. 30, 1983; 56 FR...

78 FR 51807 - Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-21

... Permits for Reusable Suborbital Rockets AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice... INFORMATION: OMB Control Number: 2120-0722. Title: Experimental Permits for Reusable Suborbital Rockets. Form... experimental permits for reusable suborbital rockets to authorize launches for the purpose of research and...

77 FR 54382 - Revisions of Five California Clean Air Act Title V Operating Permits Programs

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-05

... Five California Clean Air Act Title V Operating Permits Programs AGENCY: Environmental Protection... Permits (Title V) programs of the Monterey Bay Unified Air Pollution Control District (MBUAPCD), San Luis... thresholds in EPA's Tailoring Rule, which have not been previously subject [[Page 54383

Development of immune-complex glomerulonephritis in athymic mice: T cells are not required for the genesis of glomerular injury.

PubMed

Bagheri, Nayer; Pepple, Douglas A; Hassan, Medhat O; Harding, Clifford V; Emancipator, Steven N

2005-03-01

Chronic injection of dextran into normal mice elicits a glomerulonephritis (GN) that models IgA nephropathy (IgAN) in humans. Since athymic mice lack T cells but nonetheless develop antibodies to polysaccharide antigens such as dextran (DEX), we used athymic mice to study the role of T lymphocytes in the induction of this form of GN, independent of the role of T cells in antibody synthesis. Both mice given injections of diethylaminoethyl (DEAE)-DEX and uninjected mice had circulating IgM and IgA anti-DEX antibodies, which apparently arise as 'natural antibodies', but immune complex GN was observed only in the injected mice. All of 15 injected mice exhibited capillary staining for IgA and IgM; none of 12 control mice contained such IgA deposits and only one had capillary staining for IgM (both P<0.001). In addition, IgG and C3 were detected in injected but not control animals. By light microscopy, injected mice exhibited marked expansion of mesangial matrix relative to controls. Electron microscopy showed no glomerular abnormalities in control mice, whereas injected mice showed large organized fibrillar deposits principally in the mesangium. Hematuria and proteinuria were present in all 15 injected mice, but only one of 11 control mice showed hematuria or proteinuria (both P<0.001). These results indicate that chronic injection of DEAE-DEX into athymic mice generates the same clinical and histologic features of GN as in euthymic mice, suggesting that T cells are not necessary to promote GN in this model.

Initiation into prescription opioid injection and associated trends in heroin use among people who use illicit drugs.

PubMed

Lake, Stephanie; Milloy, M-J; Dong, Huiru; Hayashi, Kanna; Wood, Evan; Kerr, Thomas; DeBeck, Kora

2016-12-01

Prescription opioid (PO) injection among people who use illicit drugs (PWUD) is an ongoing concern, yet little is known about drug use trajectories associated with initiating PO injection, including potential associations with heroin use. This study aimed to identify predictors of PO injection initiation among PWUD, and examine trends in heroin use before and after initiating PO injection. Data were merged from three cohorts of PWUD recruited between September 2005 and November 2015. Predictors of PO injection initiation were identified using extended Cox regression models. Trends in heroin use pre- and post-initiation were examined with McNemar's test and compared to matched controls with linear growth curve models. Among 1580 participants, 247 initiated PO injection yielding an incidence density of 3.9 (95% Confidence Interval [CI]: 3.4-4.4) per 100 person-years. In a multivariable analysis, independent predictors of PO injection initiation included heroin injection (Adjusted Hazard Ratio [AHR]=4.39, 95% CI: 3.24-5.95) and non-injection PO use (AHR=1.99, 95% CI: 1.25-3.17). In a sub-analysis, compared to matched controls, PO injection corresponded with elevated heroin use post-initiation (p≤0.05). In this study, heroin use and non-injection PO use strongly predicted PO injection initiation. Those who initiated PO injecting had elevated heroin use patterns post-initiation compared to controls. These findings suggest that transitioning to PO injection does not appear to be a substitute for heroin use among PWUD. These findings highlight the importance of addressing PO injection in harm reduction and treatment settings. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Method for controlling corrosion in thermal vapor injection gases

DOEpatents

Sperry, John S.; Krajicek, Richard W.

1981-01-01

An improvement in the method for producing high pressure thermal vapor streams from combustion gases for injection into subterranean oil producing formations to stimulate the production of viscous minerals is described. The improvement involves controlling corrosion in such thermal vapor gases by injecting water near the flame in the combustion zone and injecting ammonia into a vapor producing vessel to contact the combustion gases exiting the combustion chamber.

40 CFR 146.81 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... INJECTION CONTROL PROGRAM: CRITERIA AND STANDARDS Criteria and Standards Applicable to Class VI Wells § 146... control programs to regulate any Class VI carbon dioxide geologic sequestration injection wells. (b) This...-authorized Class I, Class II, or Class V experimental carbon dioxide injection projects who seek to apply for...

40 CFR 146.81 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-07-01

... INJECTION CONTROL PROGRAM: CRITERIA AND STANDARDS Criteria and Standards Applicable to Class VI Wells § 146... control programs to regulate any Class VI carbon dioxide geologic sequestration injection wells. (b) This...-authorized Class I, Class II, or Class V experimental carbon dioxide injection projects who seek to apply for...

40 CFR 146.81 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

... INJECTION CONTROL PROGRAM: CRITERIA AND STANDARDS Criteria and Standards Applicable to Class VI Wells § 146... control programs to regulate any Class VI carbon dioxide geologic sequestration injection wells. (b) This...-authorized Class I, Class II, or Class V experimental carbon dioxide injection projects who seek to apply for...

40 CFR 146.81 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... INJECTION CONTROL PROGRAM: CRITERIA AND STANDARDS Criteria and Standards Applicable to Class VI Wells § 146... control programs to regulate any Class VI carbon dioxide geologic sequestration injection wells. (b) This...-authorized Class I, Class II, or Class V experimental carbon dioxide injection projects who seek to apply for...

Optimizing Injection Molding Parameters of Different Halloysites Type-Reinforced Thermoplastic Polyurethane Nanocomposites via Taguchi Complemented with ANOVA

PubMed Central

Gaaz, Tayser Sumer; Sulong, Abu Bakar; Kadhum, Abdul Amir H.; Nassir, Mohamed H.; Al-Amiery, Ahmed A.

2016-01-01

Halloysite nanotubes-thermoplastic polyurethane (HNTs-TPU) nanocomposites are attractive products due to increasing demands for specialized materials. This study attempts to optimize the parameters for injection just before marketing. The study shows the importance of the preparation of the samples and how well these parameters play their roles in the injection. The control parameters for injection are carefully determined to examine the mechanical properties and the density of the HNTs-TPU nanocomposites. Three types of modified HNTs were used as untreated HNTs (uHNTs), sulfuric acid treated (aHNTs) and a combined treatment of polyvinyl alcohol (PVA)-sodium dodecyl sulfate (SDS)-malonic acid (MA) (treatment (mHNTs)). It was found that mHNTs have the most influential effect of producing HNTs-TPU nanocomposites with the best qualities. One possible reason for this extraordinary result is the effect of SDS as a disperser and MA as a crosslinker between HNTs and PVA. For the highest tensile strength, the control parameters are demonstrated at 150 °C (injection temperature), 8 bar (injection pressure), 30 °C (mold temperature), 8 min (injection time), 2 wt % (HNTs loading) and mHNT (HNTs type). Meanwhile, the optimized combination of the levels for all six control parameters that provide the highest Young’s modulus and highest density was found to be 150 °C (injection temperature), 8 bar (injection pressure), 32 °C (mold temperature), 8 min (injection time), 3 wt % (HNTs loading) and mHNT (HNTs type). For the best tensile strain, the six control parameters are found to be 160 °C (injection temperature), 8 bar (injection pressure), 32 °C (mold temperature), 8 min (injection time), 2 wt % (HNTs loading) and mHNT (HNTs type). For the highest hardness, the best parameters are 140 °C (injection temperature), 6 bar (injection pressure), 30 °C (mold temperature), 8 min (injection time), 2 wt % (HNTs loading) and mHNT (HNTs type). The analyses are carried out by coordinating Taguchi and ANOVA approaches. Seemingly, mHNTs has shown its very important role in the resulting product. PMID:28774069

Optimizing Injection Molding Parameters of Different Halloysites Type-Reinforced Thermoplastic Polyurethane Nanocomposites via Taguchi Complemented with ANOVA.

PubMed

Gaaz, Tayser Sumer; Sulong, Abu Bakar; Kadhum, Abdul Amir H; Nassir, Mohamed H; Al-Amiery, Ahmed A

2016-11-22

Halloysite nanotubes-thermoplastic polyurethane (HNTs-TPU) nanocomposites are attractive products due to increasing demands for specialized materials. This study attempts to optimize the parameters for injection just before marketing. The study shows the importance of the preparation of the samples and how well these parameters play their roles in the injection. The control parameters for injection are carefully determined to examine the mechanical properties and the density of the HNTs-TPU nanocomposites. Three types of modified HNTs were used as untreated HNTs ( u HNTs), sulfuric acid treated ( a HNTs) and a combined treatment of polyvinyl alcohol (PVA)-sodium dodecyl sulfate (SDS)-malonic acid (MA) (treatment ( m HNTs)). It was found that m HNTs have the most influential effect of producing HNTs-TPU nanocomposites with the best qualities. One possible reason for this extraordinary result is the effect of SDS as a disperser and MA as a crosslinker between HNTs and PVA. For the highest tensile strength, the control parameters are demonstrated at 150 °C (injection temperature), 8 bar (injection pressure), 30 °C (mold temperature), 8 min (injection time), 2 wt % (HNTs loading) and m HNT (HNTs type). Meanwhile, the optimized combination of the levels for all six control parameters that provide the highest Young's modulus and highest density was found to be 150 °C (injection temperature), 8 bar (injection pressure), 32 °C (mold temperature), 8 min (injection time), 3 wt % (HNTs loading) and m HNT (HNTs type). For the best tensile strain, the six control parameters are found to be 160 °C (injection temperature), 8 bar (injection pressure), 32 °C (mold temperature), 8 min (injection time), 2 wt % (HNTs loading) and m HNT (HNTs type). For the highest hardness, the best parameters are 140 °C (injection temperature), 6 bar (injection pressure), 30 °C (mold temperature), 8 min (injection time), 2 wt % (HNTs loading) and m HNT (HNTs type). The analyses are carried out by coordinating Taguchi and ANOVA approaches. Seemingly, m HNTs has shown its very important role in the resulting product.

Submucosal injection of normal saline may prevent tissue damage from argon plasma coagulation: an experimental study using resected porcine esophagus, stomach, and colon.

PubMed

Fujishiro, Mitsuhiro; Yahagi, Naohisa; Nakamura, Masanori; Kakushima, Naomi; Kodashima, Shinya; Ono, Satoshi; Kobayashi, Katsuya; Hashimoto, Takuhei; Yamamichi, Nobutake; Tateishi, Ayako; Shimizu, Yasuhito; Oka, Masashi; Ichinose, Masao; Omata, Masao

2006-10-01

Argon plasma coagulation (APC) is considered to be a safe thermocoagulation technique, but some reports show perforation and deformity during and after APC. In this study, we investigated the usefulness of prior submucosal injection for APC. APC over the mucosa was performed on fresh resected porcine esophagus, stomach, and colon with prior submucosal injection of normal saline (injection group) and without it (control group). The depth of tissue damage increased linearly with pulse duration up to the shallower submucosal layer in both groups. After that, tissue damage in the injection group remained confined to the shallower submucosal layer under any condition, whereas that in the control group continued to extend. The tissue damages of the injection groups were significantly (P<0.05) shallower than those of the control groups that reached the deeper submucosal layer in all the organs. Submucosal injection of normal saline before the application of APC may limit tissue damage and prevent perforation and deformity.

Effects of intracerebroventricular injections of free fatty acids, lysophospholipids, or platelet activating factor in a mouse model of orofacial pain.

PubMed

Vahidy, Wajiha H; Ong, Wei-Yi; Farooqui, Akhlaq A; Yeo, Jin-Fei

2006-10-01

The present study was carried out to determine the effects of central nervous free fatty acids, lysophospholipids, or platelet activating factor (PAF), in a mouse facial carrageenan injection model of orofacial pain. Mice that received intracerebroventricular (I.C.V.) injection of arachidonic acid or oleic acid showed significantly reduced allodynia and behavioral responses to von Frey hair stimulation of a carrageenan-injected area of the face, at 8 h post-injection, compared to controls that received I.C.V. injection of vehicle. In contrast to free fatty acids, increased responses were observed in mice at 72 h after I.C.V. lysophosphatidic acid or lysophosphatidylcholine injection, and at 8 and 24 h after PAF injection, compared vehicle injected controls. Information regarding pro-nociceptive effect of specific brain lipids may be a useful basis for further studies to explore mechanism.

Spallation processes and nuclear interaction products of cosmic rays.

PubMed

Silberberg, R; Tsao, C H

1990-08-01

Most cosmic-ray nuclei heavier than helium have suffered nuclear collisions in the interstellar gas, with transformation of nuclear composition. The isotopic and elemental composition at the sources has to be inferred from the observed composition near the Earth. The source composition permits tests of current ideas on sites of origin, nucleosynthesis in stars, evolution of stars, the mixing and composition of the interstellar medium and injection processes prior to acceleration. The effects of nuclear spallation, production of radioactive nuclides and the time dependence of their decay provide valuable information on the acceleration and propagation of cosmic rays, their nuclear transformations, and their confinement time in the Galaxy. The formation of spallation products that only decay by electron capture and are relatively long-lived permits an investigation of the nature and density fluctuations (like clouds) of the interstellar medium. Since nuclear collisions yield positrons, antiprotons, gamma rays and neutrinos, we shall discuss these topics briefly.

Long-acting oxytetracycline prophylaxis to protect susceptible cattle introduced into an area of Kenya with endemic East Coast fever.

PubMed

Chumo, R S; Irvin, A D; Morzaria, S P; Katende, J; Purnell, R E

1989-03-04

Two field trials were carried out in successive years at the Ngong Veterinary Farm, Kenya, in which young cattle, previously unexposed to tick-borne diseases, were introduced into an area with endemic East Coast fever while protected by a series of injections of a long-acting oxytetracycline. In 1984, 12 animals which received injections of 20 mg/kg of the drug on days 0, 7, 14 and 21 after introduction, together with 12 untreated controls, were exposed without tick control until clinical disease occurred. All 12 control animals contracted East Coast fever by day 24 and 10 of them died. Five of the 12 injected animals had detectable parasites, and one of them required antitheilerial treatment. In 1985, four groups of 10 calves were introduced. One group received injections of 20 mg/kg of oxytetracycline on days 7 and 14, one group received injections on days 7, 14 and 21, and a third group received injections on days 7, 12 and 17; the fourth group (controls) had no treatment until clinical disease occurred. By day 35 all the control animals had contracted the disease and one had died despite antitheilerial treatment. Three injections of oxytetracycline suppressed the disease so that mild reactions occurred in only four animals in each group, but two injections failed to prevent severe reactions in two animals and mild reactions in four others.(ABSTRACT TRUNCATED AT 250 WORDS)

Control of Viscous Fingering in Miscible Displacements in Porous Media with a Periodic Change of Injection Rate

NASA Astrophysics Data System (ADS)

Yuan, Q.; Zeng, F.; Knorr, K. D.; Imran, M.

2017-12-01

Context/PurposeThe viscous fingering (VF) is widely encountered in a series of miscible displacements such as CO2 sequestration and solvent-based enhanced oil recovery (EOR). Accurate prediction and effective control of its development are significant. Commercial simulators cannot capture VF because of large numerical diffusion. Moreover, previous measures for controlling VF using polymer are very expensive. In the present study, a periodic change of injection rate involving injection and extraction is used to control and reduce VF instabilities at zero cost. MethodsHighly accurate spectral method and fully implicit alternating direction implicit method are used to simulate VF with concentration-dependent diffusion (CDD) and velocity-induced dispersion (VID), although the consideration of CDD and VID may result in strong nonlinearity and stiff problem under unfavourable viscosity ratio. In-house code is developed. The VF is reduced by optimizing period and amplitude of injection rate. ResultsThe results show that the periodic change of injection rates can strongly affect VF and sweep efficiency. In particular, a period-stabilizing range is found in which the VF is reduced compared with widely used constant injection with the same amount of fluid injected. The frequent change of rate results in high sweep efficiency. The optimal injection scheme, when compared with constant injection, can improve sweep efficiency by 20-35%. InterpretationDispersion plays a key role in the mitigation of VF in periodic displacement rates. It enhances the uniform mixing of two fluids in injection stage in any period, while it can more effectively attenuate VF instabilities through the following extraction stage. Fast switch of injection and extraction can mitigate flow instability once it develops. ConclusionThis finding is very novel and significant as it is the first time to control VF instability in porous media without any additional cost. It shows great potential for EOR at zero cost.

THE USE OF I$sup 125$ LABELED DIIODOFLUORESCEIN IN THE DETECTION OF HUMAN INTRAOCULAR NEOPLASMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goren, S.B.; Newell, E.W.; Brizel, H.E.

The new method which is described is believed to be superior to the usual method for detection of intraocular tumors using P/sup 32/. Because of the limited penetration of beta rays, the use of P/sup 32/ imposes relatively strict geometric restrictions and its usefulness in posterior-segment tumors is limited. The patient receives a single intravenous injection of 5.0 mu c/kg body weight of diiodofluorescein-I/sup 125/, the specific activity of which is 17 mg/mc. External counting over each closed eye is carried out with a hand scintillation counter 1, 5, 8, and 24 hr after injection. Ocular counts are performed bymore » resting the window of the counter against the closed lids; the cavernous sinus is measured by placing the counter just above the bridge of the nose. ln the 17 patients studied, eyes with neoplasms contained at least 23% more radioactivity after 8 hr than did the healthy eye. Control eyes, not containing neoplasms (idiopathic retinal detachment, retinoschisis, benign nevus, macular degeneration, phthisis bulbi, absolute glaucoma), showed less than a 13% differential. One false negative test was obtained, a patient with a metastatic bronchogenic adenocarcinoma to the choroid; no false positives were seen. Diiodofluorescein labeled with I/sup 131/ has been widely used as a diagnostic aid in suspected intracranial neoplasms. However, since the gamma rays of I/sup 131/ have a half-value layer in tissue of 6.9 cm, it has not been helpful in ocular disease; the gamma rays arising from the cavernous sinus interfere with accurate counting of intraocular radiation. I/sup 125/ decays by a complicated scheme, the most important as far as ocular studies are concerned being soft photons of 27.3 and 35.4 kev energies. It has a half-value layer in tissue of 1.9 to 2.5 cm. Therefore, it is feasible to measure radiation of the posterior globe with only minimal interference from radiation arising in the brain sinuses. Its half-life of 60 days results in a greatly increased shelf-life of tagged compounds than when I/sup 131/ is used. Additionally, it has a lower energy of radiation than I/sup 131/ which reduces shielding requirements and permits more efficient detector design. These factors permit enhanced counting efficiency and scanning resolution and lead to a decreased dosage of radiation to the patient. It is thus permissible to use the compound in children in whom P/sup 32/ counting is generally considered contraindicated. However, although the total-body irradiation received during this test is not excessive, it has not been used in pregnant women. The administration of Lugol's solution prior to the test prevents excessive concentration of any free circulating radioactive iodine in the thyroid gland. Diiodofluorescein-I/sup 125/ is not retained by intraocular neoplasms for prolonged periods of time, the most significant counts appearing 8 hr after intravenous injection. About 50% of the injected dose is excreted in the urine and feces within the first 24 hr after injection. The absolute count found in the eye after 8 hr is in the order of 40,000 cpm. After 24 hr, this decreases to approximates 15,000 cpm. The ratio of counts over liver, thyroid, eye, and cavernous sinus is about 4 : 2 : 1 : 0.4. The ratio of counts between the 2 eyes is more significant than the absolute number of counts. This may limit the usefulness of this procedure in monocular patients. (H.H.D.)« less

Apparatus and method to inject a reductant into an exhaust gas feedstream

DOEpatents

Viola, Michael B [Macomb Township, MI

2009-09-22

An exhaust aftertreatment system for an internal combustion engine is provided including an apparatus and method to inject a reductant into the exhaust gas feedstream. Included is a fuel metering device adapted to inject reductant into the exhaust gas feedstream and a controllable pressure regulating device. A control module is operatively connected to the reductant metering device and the controllable pressure regulating device, and, adapted to effect flow of reductant into the exhaust gas feedstream over a controllable flow range.

Minimizing the endophthalmitis rate following intravitreal injections using 0.25% povidone-iodine irrigation and surgical mask.

PubMed

Shimada, Hiroyuki; Hattori, Takayuki; Mori, Ryusaburo; Nakashizuka, Hiroyuki; Fujita, Kyoko; Yuzawa, Mitsuko

2013-08-01

To examine the efficacy of complying with an infection control manual for intravitreal injection of anti-vascular endothelial growth factor (VEGF) preparations in reducing the rate of endophthalmitis. We retrospectively reviewed intravitreal anti-VEGF injections conducted by vitreoretinal specialists at the outpatient injection room of a single university hospital between July 2009 and July 2012. The injections were conducted following an infection control manual established by our department. Doctors and nurses wore surgical masks, and disinfected the patient's eyelid skin with 10% povidone-iodine and then the conjunctiva with 0.25% povidone-iodine. After putting a drape on the patient's face, a lid speculum was placed. The conjunctival surface was again washed with 5 ml of 0.25% povidone-iodine. After waiting at least 30 seconds, intravitreal injection was performed through povidone-iodine. Following injection, the injection site was again washed with 5 ml of 0.25% povidone-iodine. Patients were treated with topical levofloxacin 4 times a day for 3 days before and after the injection. A total of 15,144 injections comprising 548 injections of pegaptanib sodium, 846 injections of bevacizumab, and 13,750 injections of ranibizumab were performed. During this period, no case of suspected or proven infectious endophthalmitis occurred. The endophthalmitis rate was 0 per 15,144 injections, (95% confidence interval, 0.0-0.0%). The results suggest that endophthalmitis can be reduced to a minimum by preventing normal flora of the conjunctiva and bacteria in the oral cavity from entering the vitreous. For this purpose, an infection control manual that requires nurses and doctors to wear surgical mask and drape the patient's face, irrigate the conjunctiva with 0.25% povidone-iodine and wait at least 30 seconds before performing intravitreal injection is useful.

Wastewater Disposal Wells, Fracking, and Environmental Injustice in Southern Texas

PubMed Central

Werder, Emily; Sebastian, Daniel

2016-01-01

Objectives. To investigate race and poverty in areas where oil and gas wastewater disposal wells, which are used to permanently inject wastewater from hydraulic fracturing (fracking) operations, are permitted. Methods. With location data of oil and gas disposal wells permitted between 2007 and 2014 in the Eagle Ford area, a region of intensive fracking in southern Texas, we analyzed the racial composition of residents living less than 5 kilometers from a disposal well and those farther away, adjusting for rurality and poverty, using a Poisson regression. Results. The proportion of people of color living less than 5 kilometers from a disposal well was 1.3 times higher than was the proportion of non-Hispanic Whites. Adjusting for rurality, disposal wells were 2.04 times (95% confidence interval = 2.02, 2.06) as common in areas with 80% people of color or more than in majority White areas. Disposal wells are also disproportionately sited in high-poverty areas. Conclusions. Wastewater disposal wells in southern Texas are disproportionately permitted in areas with higher proportions of people of color and residents living in poverty, a pattern known as “environmental injustice.” PMID:26794166

Some variables affecting hardwood control with stem injections of 2,4,5-T.

Treesearch

John L. Arend

1967-01-01

The water-soluble amine salt was at least four times more effective than the oil-soluble ester. Concentration of the 2,4,5-T, spacing of the injections, and season of the year were also important; height of the spaced injections was not. The effects of these variables and of crown size and character of the branching on hardwood control with 2,4,5-T injections are...

Mortality, size of the gonads, and ultrastructure of primordial germ cell in chick embryos treated with gamma-irradiation or injected with donor cells.

PubMed

Maeda, T; Clark, M E; Etches, R J

1998-06-01

The effects of injection and/or gamma-irradiation prior to injection on mortality, size of the gonads, and ultrastructure of primordial germ cell (PGC) were examined after 5 d of incubation. The mortality of embryos injected with donor cells was significantly higher than that of control and irradiated embryos. All irradiated embryos were alive, although their development was delayed compared to those not exposed to irradiation. The size of the gonads of embryos injected with donor cells were similar to those of control embryos, however, the size of the gonads in irradiated embryos was significantly smaller than those of control embryos. The number of PGC in the gonads was significantly decreased by irradiation. There was no notable effect of irradiation or injection on the nuclei and cytoplasmic organelles in PGC.

Injection of electrons with predominantly perpendicular energy into an area of toroidal field ripple in a tokamak plasma to improve plasma confinement

DOEpatents

Ono, Masayuki; Furth, Harold

1993-01-01

An electron injection scheme for controlling transport in a tokamak plasma. Electrons with predominantly perpendicular energy are injected into a ripple field region created by a group of localized poloidal field bending magnets. The trapped electrons then grad-B drift vertically toward the plasma interior until they are detrapped, charging the plasma negative. Calculations indicate that the highly perpendicular velocity electrons can remain stable against kinetic instabilities in the regime of interest for tokamak experiments. The penetration distance can be controlled by controlling the "ripple mirror ratio", the energy of the injected electrons, and their v.sub..perp. /v.sub.51 ratio. In this scheme, the poloidal torque due to the injected radial current is taken by the magnets and not by the plasma. Injection is accomplished by the flat cathode containing an ECH cavity to pump electrons to high v.sub..perp..

Delineating Area of Review in a System with Pre-injection Relative Overpressure

DOE PAGES

Oldenburg, Curtis M.; Cihan, Abdullah; Zhou, Quanlin; ...

2014-12-31

The Class VI permit application for geologic carbon sequestration (GCS) requires delineation of an area of review (AoR), defined as the region surrounding the (GCS) project where underground sources of drinking water (USDWs) may be endangered. The methods for estimating AoR under the Class VI regulation were developed assuming that GCS reservoirs would be in hydrostatic equilibrium with overlying aquifers. Here we develop and apply an approach to estimating AoR for sites with preinjection relative overpressure for which standard AoR estimation methods produces an infinite AoR. The approach we take is to compare brine leakage through a hypothetical open flowmore » path in the base-case scenario (no-injection) to the incrementally larger leakage that would occur in the CO 2-injection case. To estimate AoR by this method, we used semi-analytical solutions to single-phase flow equations to model reservoir pressurization and flow up (single) leaky wells located at progressively greater distances from the injection well. We found that the incrementally larger flow rates for hypothetical leaky wells located 6 km and 4 km from the injection well are ~20% and 30% greater, respectively, than hypothetical baseline leakage rates. If total brine leakage is considered, the results depend strongly on how the incremental increase in total leakage is calculated, varying from a few percent to up to 40% greater (at most at early time) than base-case total leakage.« less

High force vibration testing with wide frequency range

DOEpatents

Romero, Edward F.; Jepsen, Richard A.; Gregory, Danny Lynn

2013-04-02

A shaker assembly for vibration testing includes first and second shakers, where the first shaker includes a piezo-electric material for generating vibration. A support structure permits a test object to be supported for vibration of the test object by both shakers. An input permits an external vibration controller to control vibration of the shakers.

29 CFR 1926.152 - Flammable liquids.

Code of Federal Regulations, 2014 CFR

2014-07-01

... to permit approach of fire control apparatus. (3) The storage area shall be graded in a manner to... feet of each portable tank, there shall be a 12-foot-wide access way to permit approach of fire control... storage cabinets shall be constructed in the following manner, or equivalent: The bottom, sides, and top...

31 CFR 592.201 - Prohibited importation and exportation of any rough diamond; permitted importation or exportation...

Code of Federal Regulations, 2010 CFR

2010-07-01

..., unless the rough diamond has been controlled through the Kimberley Process Certification Scheme. (b) The... States of any rough diamond not controlled through the Kimberley Process Certification Scheme do not... Process Certification Scheme and thus is not permitted, except in the following circumstance. The...

9 CFR 78.23 - Brucellosis exposed bison.

Code of Federal Regulations, 2010 CFR

2010-01-01

...” brand permit and as follows: (1) Directly to a recognized slaughtering establishment or directly to an... permit or “S” brand permit. (c) Movement other than in accordance with paragraphs (a) or (b) of this... individual herd plan. (Approved by the Office of Management and Budget under control number 0579-0051) [51 FR...

30 CFR 773.23 - Suspension or rescission requirements for improvidently issued permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... improvidently issued permits. 773.23 Section 773.23 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL... jurisdiction over the violation; (2) You or your operator no longer own or control the relevant operation; (3...

21 CFR 1210.28 - Permits waiving clause 4, section 2 of the Federal Import Milk Act.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Import Milk Act. 1210.28 Section 1210.28 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) REGULATIONS UNDER CERTAIN OTHER ACTS ADMINISTERED BY THE FOOD AND DRUG ADMINISTRATION REGULATIONS UNDER THE FEDERAL IMPORT MILK ACT Permit Control § 1210.28 Permits...

21 CFR 1210.28 - Permits waiving clause 4, section 2 of the Federal Import Milk Act.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Import Milk Act. 1210.28 Section 1210.28 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) REGULATIONS UNDER CERTAIN OTHER ACTS ADMINISTERED BY THE FOOD AND DRUG ADMINISTRATION REGULATIONS UNDER THE FEDERAL IMPORT MILK ACT Permit Control § 1210.28 Permits...

40 CFR 434.72 - Effluent limitations attainable by the application of the best practicable control technology...

Code of Federal Regulations, 2010 CFR

2010-07-01

... currently available (BPT). (a) The operator must submit a site-specific Pollution Abatement Plan to the permitting authority for the pollution abatement area. The plan must be approved by the permitting authority and incorporated into the permit as an effluent limitation. The Pollution Abatement Plan must identify...

21 CFR 1312.12 - Application for import permit.

Code of Federal Regulations, 2011 CFR

2011-04-01

... permit. (a) An application for a permit to import controlled substances shall be made on DEA Form 357. DEA Form 357 may be obtained from, and shall be filed with, the Import/Export Unit, Drug Enforcement Administration. See the Table of DEA Mailing Addresses in § 1321.01 of this chapter for the current mailing...

21 CFR 1312.12 - Application for import permit.

Code of Federal Regulations, 2010 CFR

2010-04-01

... permit. (a) An application for a permit to import controlled substances shall be made on DEA Form 357. DEA Form 357 may be obtained from, and shall be filed with, the Import/Export Unit, Drug Enforcement Administration. See the Table of DEA Mailing Addresses in § 1321.01 of this chapter for the current mailing...

76 FR 10361 - Clean Air Act Operating Permit Program; Petition for Objection to State Operating Permit for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-24

... July 14, 2010 response of the CDPHE, Air Pollution Control Division to the October 8, 2009 Order by EPA... ENVIRONMENTAL PROTECTION AGENCY [FRL-9270-5] Clean Air Act Operating Permit Program; Petition for... issued by the Colorado Department of Public Health and Environment (CDPHE). Specifically, the...

Impact of Sodium Bicarbonate-Buffered Lidocaine on Patient Pain During Image-Guided Breast Biopsy.

PubMed

Vasan, Alison; Baker, Jay A; Shelby, Rebecca A; Soo, Mary Scott C

2017-09-01

This randomized, double-blind controlled study evaluated the effectiveness of sodium bicarbonate-buffered lidocaine on reducing pain during imaging-guided breast biopsies. This prospective, HIPAA-compliant study randomly assigned 85 women undergoing ultrasound- or stereotactic-guided core-needle breast biopsies to receive intradermally and intraparenchymally either 1% lidocaine buffered with sodium bicarbonate (9:1 ratio) (bicarbonate study group) or 1% lidocaine alone (control group). Pain was evaluated using a 0-to-10 Likert pain scale during both intradermal and intraparenchymal anesthesia injections and during tissue sampling. Prebiopsy breast pain, anxiety, medical history, demographics, biopsy type, radiologist level of training, breast density, and lesion histology were recorded. Data were analyzed using analysis of variance and analysis of covariance. Unadjusted mean pain scores were 1.47 and 2.07 (study and control groups, respectively; P = .15) during intradermal injections, and 1.84 and 2.98 (study and control groups, respectively; P = .03) during intraparenchymal injections. Tissue sampling mean pain scores were .81 and 1.71 (study and control groups, respectively; P = .07). Moderator analyses found (1) among patients with preprocedural pain, those in the bicarbonate group experienced less intradermal injection pain (0.85 ± 1.23) than patients in the control group (2.50 ± 2.09); (2) among patients with fatty or scattered fibroglandular tissue, those in the bicarbonate group (1.35 ± 1.95) experienced less intraparenchymal injection pain than the control group (3.52 ± 3.13); and (3) during ultrasound-guided biopsies, patients in the bicarbonate group experienced less tissue-sampling pain (0.23 ± 0.63) than the control group (1.79 ± 3.05). Overall, buffering lidocaine with sodium bicarbonate significantly reduced pain during intraparenchymal injections, and additional pain reduction was found in certain patient subgroups during intradermal injections, intraparenchymal injections, and tissue sampling. Copyright © 2017 American College of Radiology. Published by Elsevier Inc. All rights reserved.

Recycling of aluminium scrap for secondary Al-Si alloys.

PubMed

Velasco, Eulogio; Nino, Jose

2011-07-01

An increasing amount of recycled aluminium is going into the production of aluminium alloy used for automotive applications. In these applications, it is necessary to control and remove alloy impurities and inclusions. Cleaning and fluxing processes are widely used during processing of the alloys for removal of inclusions, hydrogen and excess of magnesium. These processes use salt fluxes based in the system NaCl-KCl, injection of chlorine or mixture of chlorine with an inert gas. The new systems include a graphite wand and a circulation device to force convection in the melt and permit the bubbling and dispersion of reactive and cleaning agents. This paper discusses the recycling of aluminium alloys in rotary and reverberatory industrial furnaces. It focuses on the removal of magnesium during the melting process. In rotary furnaces, the magnesium lost is mainly due to the oxidation process at high temperatures. The magnesium removal is carried out by the reaction between chlorine and magnesium, with its efficiency associated to kinetic factors such as concentration of magnesium, mixing, and temperature. These factors are also related to emissions generated during the demagging process. Improvements in the metallic yield can be reached in rotary furnaces if the process starts with a proper salt, with limits of addition, and avoiding long holding times. To improve throughput in reverberatories, start the charging with high magnesium content material and inject chlorine gas if the molten metal is at the right temperature. Removal of magnesium through modern technologies can be efficiently performed to prevent environmental problems.

Study and optimization of lower hybrid wave coupling in advanced scenario plasmas in JET

NASA Astrophysics Data System (ADS)

Pericoli Ridolfini, V.; Ekedahl, A.; Erents, S. K.; Mailloux, J.; Podda, S.; Sarazin, Y.; Tuccillo, A. A.; Workprogramme contributors, EFDA-JET

2004-02-01

Active current drive with lower hybrid (LH) waves in the advanced scenario plasmas at JET-EFDA was successful after a systematic study of the coupling problems that derive from the H-mode features of the edge plasma, namely very low density and ELM activity. The LH coupling has been improved compared to the past, by making the edge plasma in front of the LH launcher denser and more uniform. Injecting deuterated methane (CD4) from a nearby gas pipe increases the density in front of the LH launcher at least by a factor of 1.5, above the cut-off value for the LH frequency. A better matching of the plasma shape to that of the LH antenna makes the plasma ahead of the LH launcher more regular along the poloidal angle. These two techniques together have permitted a balanced supply of the three LH grills, with an average reflection below 4%, as in the previous L-mode operation. CD4 does not affect the performances nor does it contaminate the main plasma up to the maximum flow rate so far used, \\Phi_{CD_4}>10^{22}el\\,s^{-1} and now it is routinely applied in JET (up to 4 MW have been injected for longer than 8 s) with very encouraging results for LHCD. Even though CD4 is not suitable for ITER for tritium retention, the possibility of controlling locally and safely the scrape-off plasma density has been demonstrated.

Nitrogen oxides from waste incineration: control by selective non-catalytic reduction.

PubMed

Zandaryaa, S; Gavasci, R; Lombardi, F; Fiore, A

2001-01-01

An experimental study of the selective non-catalytic reduction (SNCR) process was carried out to determine the efficiency of NOx removal and NH3 mass balance, the NOx reducing reagent used. Experimental tests were conducted on a full-scale SNCR system installed in a hospital waste incineration plant. Anhydrous NH3 was injected at the boiler entrance for NOx removal. Ammonia was analyzed after each flue-gas treatment unit in order to establish its mass balance and NH3 slip in the stack gas was monitored as well. The effective fraction of NH3 for the thermal NOx reduction was calculated from measured values of injected and residual NH3. Results show that a NOx reduction efficiency in the range of 46.7-76.7% is possible at a NH3/NO molar ratio of 0.9-1.5. The fraction of NH3 used in NOx removal was found to decrease with rising NH3/NO molar ratio. The NH3 slip in the stack gas was very low, below permitted limits, even at the higher NH3 dosages used. No direct correlation was found between the NH3/NO molar ratio and the NH3 slip in the stack gas since the major part of the residual NH3 was converted into ammonium salts in the dry scrubbing reactor and subsequently collected in the fabric filter. Moreover, another fraction of NH3 was dissolved in the scrubbing liquor.

Microneedle-based vaccines

PubMed Central

Prausnitz, Mark R.; Mikszta, John A.; Cormier, Michel; Andrianov, Alexander K.

2010-01-01

The threat of pandemic influenza and other public health needs motivates development of better vaccine delivery systems. To address this need, microneedles have been developed as micron-scale needles fabricated using low-cost manufacturing methods that administer vaccine into the skin using a simple device that may be suitable for self-administration. Delivery using solid or hollow microneedles can be accomplished by (i) piercing the skin and then applying a vaccine formulation or patch onto the permeabilized skin, (ii) coating or encapsulating vaccine onto or within microneedles for rapid, or delayed, dissolution and release in the skin and (iii) injection into the skin using a modified syringe or pump. Extensive clinical experience with smallpox, TB and other vaccines has shown that vaccine delivery into the skin using conventional intradermal injection is generally safe and effective and often elicits the same immune responses at lower doses compared to intramuscular injection. Animal experiments using microneedles have shown similar benefits. Microneedles have been used to deliver whole, inactivated virus; trivalent split antigen vaccines; and DNA plasmid encoding the influenza hemagglutinin to rodents and found strong antibody responses. In addition, ChimeriVax™-JE against yellow fever was administered to non-human primates and generated protective levels of neutralizing antibodies more than seven times greater than subcutaneous delivery; DNA plasmid encoding hepatitis B surface antigen was administered to mice and generated antibody and T cell responses at least as strong as hypodermic injections; recombinant Protective Antigen of Baccilus anthracis was administered to rabbits and provided complete protection from lethal aerosol anthrax spore challenge at a lower dose than intramuscular injection; and DNA plasmid encoding four vaccinia virus genes administered to mice in combination with electroporation generated neutralizing antibodies that apparently included both Th1 and Th2 responses. Dose sparing with microneedles was specifically studied in mice with the model vaccine ovalbumin. At low dose (1 µg), specific antibody titers from microneedles were one order of magnitude greater than subcutaneous injection and two orders of magnitude greater than intramuscular injection. At higher doses, antibody responses increased for all delivery methods. At the highest levels (20–80 µg), the route of administration had no significant effect on the immune response. Concerning safety, no infections or other serious adverse events have been observed in well over 1000 microneedle insertions in human and animal subjects. Bleeding generally does not occur for short microneedles (<1 mm). Highly localized, mild and transient erythema is often observed. Microneedle pain has been reported as non-existent to mild, and always much less than a hypodermic needle control. Overall, these studies suggest that microneedles may provide a safe and effective method to deliver vaccines with possible added attributes of requiring lower vaccines doses, permitting low-cost manufacturing, and enabling simple distribution and administration. PMID:19768415

14 CFR 23.1143 - Engine controls.

Code of Federal Regulations, 2014 CFR

2014-01-01

... independent of those for every other engine or supercharger. (e) For each fluid injection (other than fuel... flow of the injection fluid is adequately controlled. (f) If a power, thrust, or a fuel control (other than a mixture control) incorporates a fuel shutoff feature, the control must have a means to prevent...

14 CFR 23.1143 - Engine controls.

Code of Federal Regulations, 2013 CFR

2013-01-01

... independent of those for every other engine or supercharger. (e) For each fluid injection (other than fuel... flow of the injection fluid is adequately controlled. (f) If a power, thrust, or a fuel control (other than a mixture control) incorporates a fuel shutoff feature, the control must have a means to prevent...

Enzymatic recontouring of auricular cartilage in a rabbit model.

PubMed

Massengill, Phillip L; Goco, Paulino E; Norlund, L Layne; Muir-Padilla, Jeanne

2005-01-01

To evaluate the effectiveness of contouring auricular cartilage in a rabbit model using biologically active enzymes injected subcutaneously. The first phase determined the most effective volume and concentration required to affect the cartilage. To accomplish this task, we used ex vivo rabbit ears from a slaughterhouse. In the second phase, we injected 1 mL of hyaluronidase (150 U per milliliter of isotonic sodium chloride solution [saline]), elastase (1 mg per milliliter of saline), or saline into the ears of live rabbits. The study took place at the Madigan Army Medical Center (Tacoma, Wash), and included 10 animals. In each rabbit, we injected the test compound in one ear and saline in the other ear (control). We injected hyaluronidase in 5 ears and elastase in 5 ears. After injection, the ears were contoured and splinted for 4 weeks. In the third phase, we changed the injection pathway in 5 animals. At 4 weeks, 4 (80%) of the 5 ears injected with hyaluronidase showed full response and 1 (20%) had a partial response. Of the 5 ears injected with elastase, 4 (80%) showed a full response while 1 (20%) demonstrated a partial response. There was a response in all 10 of the ears injected with a test compound. Of the 10 control ears, 3 (30%) showed a partial response. At 6 weeks, approximately 6 (30%) of the ears had maintained contour demonstrating a full response. The difference between the test ears and the control ears was statistically significant (P = .006). Compared with the control ears, the results were statistically significant for elastase (P = .004) and hyaluronidase (P = .02). Overall, both agents demonstrated a subjective and objective response compared with control ears. This study demonstrates that bioactive enzymes and splinting can be effective in correcting ear deformities in a rabbit model.

Optimizing a Male Reproductive Aging Mouse Model by d-Galactose Injection

PubMed Central

Liao, Chun-Hou; Chen, Bing-Huei; Chiang, Han-Sun; Chen, Chiu-Wei; Chen, Mei-Feng; Ke, Chih-Chun; Wang, Ya-Yun; Lin, Wei-Ning; Wang, Chi-Chung; Lin, Ying-Hung

2016-01-01

The d-galactose (d-gal)-injected animal model, which is typically established by administering consecutive subcutaneous d-gal injections to animals for approximately six or eight weeks, has been frequently used for aging research. In addition, this animal model has been demonstrated to accelerate aging in the brain, kidneys, liver and blood cells. However, studies on aging in male reproductive organs that have used this animal model remain few. Therefore, the current study aimed to optimize a model of male reproductive aging by administering d-gal injections to male mice and to determine the possible mechanism expediting senescence processes during spermatogenesis. In this study, C57Bl/6 mice were randomized into five groups (each containing 8–10 mice according to the daily intraperitoneal injection of vehicle control or 100 or 200 mg/kg dosages of d-gal for a period of six or eight weeks). First, mice subjected to d-gal injections for six or eight weeks demonstrated considerably decreased superoxide dismutase activity in the serum and testis lysates compared to those in the control group. The lipid peroxidation in testis also increased in the d-gal-injected groups. Furthermore, the d-gal-injected groups exhibited a decreased ratio of testis weight/body weight and sperm count compared to the control group. The percentages of both immotile sperm and abnormal sperm increased considerably in the d-gal-injected groups compared to those of the control group. To determine the genes influenced by the d-gal injection during murine spermatogenesis, a c-DNA microarray was conducted to compare testicular RNA samples between the treated groups and the control group. The d-gal-injected groups exhibited RNA transcripts of nine spermatogenesis-related genes (Cycl2, Hk1, Pltp, Utp3, Cabyr, Zpbp2, Speer2, Csnka2ip and Katnb1) that were up- or down-regulated by at least two-fold compared to the control group. Several of these genes are critical for forming sperm-head morphologies or maintaining nuclear integration (e.g., cylicin, basic protein of sperm head cytoskeleton 2 (Cylc2), casein kinase 2, alpha prime interacting protein (Csnka2ip) and katanin p80 (WD40-containing) subunit B1 (Katnb1)). These results indicate that d-gal-injected mice are suitable for investigating male reproductive aging. PMID:26771610

RimabotulinumtoxinB Injection

MedlinePlus

... tightening of the neck muscles that may cause neck pain and abnormal head positions). RimabotulinumtoxinB injection is in ... cannot be substituted for another.RimabotulinumtoxinB injection controls ... longer before you feel the full benefit of rimabotulinumtoxinB injection.

Corticosteroid Injection for the Treatment of Morton's Neuroma: A Prospective, Double-Blinded, Randomized, Placebo-Controlled Trial.

PubMed

Lizano-Díez, Xavier; Ginés-Cespedosa, Alberto; Alentorn-Geli, Eduard; Pérez-Prieto, Daniel; González-Lucena, Gemma; Gamba, Carlo; de Zabala, Santiago; Solano-López, Alberto; Rigol-Ramón, Pau

2017-09-01

The effectiveness of corticosteroid injection for the treatment of Morton's neuroma is unclear. In addition, most of the studies related to it are case-control or retrospective case series. The purpose of this study was to compare the effectiveness between corticosteroid injection associated with local anesthetic and local anesthetic alone (placebo control group) for the treatment of Morton's neuroma. Forty-one patients with a diagnosis of Morton's neuroma were randomized to receive 3 injections of either a corticosteroid plus a local anesthetic or a local anesthetic alone. The patients and the researcher who collected data were blinded to the treatment groups. The visual analog scale for pain and the American Orthopaedic Foot & Ankle Score (metatarsophalangeal/interphalangeal score) were obtained at baseline, after each injection, and at 3 and 6 months after the last injection. There were no significant between-group differences in terms of pain and function improvement at 3 and 6 months after treatment completion in comparison with baseline values. At the end of the study, 17 (48.5%) patients requested surgical excision of the neuroma: 7 (44%) in the experimental group and 10 (53%) in the control group ( P = 1.0). The injection of a corticosteroid plus a local anesthetic was not superior to a local anesthetic alone in terms of pain and function improvement in patients with Morton's neuroma. Level I, randomized controlled trial.

New Treatments for Drug-Resistant Epilepsy that Target Presynaptic Transmitter Release

DTIC Science & Technology

2014-07-01

mice injected with saline vehicle for 4 weeks (control no treatment=C-NT, n=5), b) pilocarpine-treated SpH mice that developed status epilepticus ...injected with saline ( status epilepticus no treatment=SE–NT, n=5), c) control SpH mice injected with levetiracetam (see below) (control treated=C-T, n...4), and d) pilocarpine-treated SpH mice that suffered status epilepticus and were treated subsequently with levetiracetam intraperitoneally (see

Injectable barriers for waste isolation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Persoff, P.; Finsterle, S.; Moridis, G.J.

In this paper the authors report laboratory work and numerical simulation done in support of development and demonstration of injectable barriers formed from either of two fluids: colloidal silica or polysiloxane. Two principal problems addressed here are control of gel time and control of plume emplacement in the vadose zone. Gel time must be controlled so that the viscosity of the barrier fluid remains low long enough to inject the barrier, but increases soon enough to gel the barrier in place. During injection, the viscosity must be low enough to avoid high injection pressures which could uplift or fracture themore » formation. To test the grout gel time in the soil, the injection pressure was monitored as grouts were injected into sandpacks. When grout is injected into the vadose zone, it slumps under the influence of gravity, and redistributes due to capillary forces as it gels. The authors have developed a new module for the reservoir simulator TOUGH2 to model grout injection into the vadose zone, taking into account the increase of liquid viscosity as a function of gel concentration and time. They have also developed a model to calculate soil properties after complete solidification of the grout. The numerical model has been used to design and analyze laboratory experiments and field pilot tests. The authors present the results of computer simulations of grout injection, redistribution, and solidification.« less

Basin-Scale Hydrologic Impacts of CO2 Storage: Regulatory and Capacity Implications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Birkholzer, J.T.; Zhou, Q.

Industrial-scale injection of CO{sub 2} into saline sedimentary basins will cause large-scale fluid pressurization and migration of native brines, which may affect valuable groundwater resources overlying the deep sequestration reservoirs. In this paper, we discuss how such basin-scale hydrologic impacts can (1) affect regulation of CO{sub 2} storage projects and (2) may reduce current storage capacity estimates. Our assessment arises from a hypothetical future carbon sequestration scenario in the Illinois Basin, which involves twenty individual CO{sub 2} storage projects in a core injection area suitable for long-term storage. Each project is assumed to inject five million tonnes of CO{sub 2}more » per year for 50 years. A regional-scale three-dimensional simulation model was developed for the Illinois Basin that captures both the local-scale CO{sub 2}-brine flow processes and the large-scale groundwater flow patterns in response to CO{sub 2} storage. The far-field pressure buildup predicted for this selected sequestration scenario suggests that (1) the area that needs to be characterized in a permitting process may comprise a very large region within the basin if reservoir pressurization is considered, and (2) permits cannot be granted on a single-site basis alone because the near- and far-field hydrologic response may be affected by interference between individual sites. Our results also support recent studies in that environmental concerns related to near-field and far-field pressure buildup may be a limiting factor on CO{sub 2} storage capacity. In other words, estimates of storage capacity, if solely based on the effective pore volume available for safe trapping of CO{sub 2}, may have to be revised based on assessments of pressure perturbations and their potential impact on caprock integrity and groundwater resources, respectively. We finally discuss some of the challenges in making reliable predictions of large-scale hydrologic impacts related to CO{sub 2} sequestration projects.« less

76 FR 55908 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-09

... of an exemption to the land disposal restrictions, under the 1984 Hazardous and Solid Waste... Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; Great Lakes... from the injection zone for as long as the waste remains hazardous. This final decision allows the...

78 FR 23246 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-18

... exemption to the land disposal Restrictions, under the 1984 Hazardous and Solid Waste [[Page 23247... Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; BASF... from the injection zone for as long as the waste remains hazardous. This final decision allows the...

77 FR 26755 - Underground Injection Control Program; Hazardous Waste Injection Restrictions; Petition for...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-07

... reissuance of an exemption to the land disposal Restrictions, under the 1984 Hazardous and Solid Waste... Waste Injection Restrictions; Petition for Exemption--Class I Hazardous Waste Injection; Diamond... from the injection zone for as long as the waste remains hazardous. This final decision allows the...

Soil Sample Report in Support of the Site 300 EWTF Ecological Risk Assessment and Permit Renewal-September 2012

DOE Office of Scientific and Technical Information (OSTI.GOV)

Terusaki, Stanley; Gallegos, Gretchen; MacQueen, Donald

2012-10-02

LLNL Site 300 has applied to renew the permits for its Explosives Waste Treatment Facility (EWTF), Explosives Waste Storage Facility (EWSF) and Building 883 Storage Facility. As a part of the permit renewal process, the Department of Toxic Substances Control (DTSC) requested LLNL to obtain soil samples in order to conduct a scoping-level ecological risk assessment pursuant to the Department of Toxic Substances Control, Guidance for Ecological Risk Assessment at Hazardous Waste Sites and Permitted Facilities, Part A: Overview, July 4, 1996. As stated in the guidance document, the scoping-level ecological risk assessment provides a framework to determine the potentialmore » interaction ecological receptors and chemicals of concern from hazardous waste treatment operations in the area of EWTF.« less

Experimental study on the role of intra-articular injection of MSCs on cartilage regeneration in haemophilia.

PubMed

Ravanbod, R; Torkaman, G; Mophid, M; Mohammadali, F

2015-09-01

Mesenchymal stem cells (MSCs) therapy is a field in progress in cartilage repair strategies. We tried to investigate the functional properties of the joint and cartilage in experimental haemarthrosis (EH) after MSCs intra-articular (IA) injection. One millilitre of fresh autologous blood was injected twice a week for three consecutive weeks in three groups including control haemophilia 10 days (n = 8), control haemophilia 38 days (n = 8) and MSCs (n = 8) group. In later, 10 days after the end of IA blood injections, MSCs IA injection was performed. Eight animals received no treatment as the normal control group. Thirty-eight days after the end of IA blood injections, animals were sacrificed. Joint friction and stress-relaxation tests were done, inflammatory cytokines of synovial membrane and scanning electron microscopy of the cartilage assessed. Joint friction decreased in MSCs in comparison to other groups and was significant with normal control group, (P = 0.011). The mechanical properties of cartilage showed no significant differences between groups. Tumour necrosis factor alpha and interleukin 1 beta decreased and IL-4 very slightly increased in MSCs in comparison to the time-matched control group. Scanning electron microscopy enabled acquisition of good structural properties of the surface and layers of the cartilage after MSCs injection. The hole induced in the medial plateau of the tibia bones, after inducing haemarthrosis, were covered with cartilage-like structure. The results showed that MSCs IA injection has some beneficial effects on cartilage structure and function in haemarthrosis model and is promising in patients with haemophilia. © 2015 John Wiley & Sons Ltd.

Soft tissue and intra-articular injection of bupivacaine, epinephrine, and morphine has a beneficial effect after total knee arthroplasty.

PubMed

Lombardi, Adolph V; Berend, Keith R; Mallory, Thomas H; Dodds, Kathleen L; Adams, Joanne B

2004-11-01

The purpose of this study was to determine if an intraoperative intraarticular and soft-tissue injection of local anaesthetic, epinephrine, and morphine has a beneficial effect for total knee arthroplasty. A control group of 138 patients (181 knees) received no intraoperative injection. The study group of 171 patients (197 knees) received intraoperative injection of 0.25% bupivacaine with epinephrine and morphine with 2/3 injected into the soft tissues and 1/3 injected into the joint. Patients having bilateral simultaneous procedures received a divided dose. The pain treatment protocol otherwise was identical. Pain, sedation, rescue narcotic usage, narcotic reversal and blood loss were examined. Pain levels during the immediate postoperative period, blood loss, and bleeding indices were reduced with injection. Considerably more control patients required rescue doses of narcotics. Preemptive analgesia with soft tissue and intra-articular injection of long-acting local anesthetic with epinephrine and morphine provides better pain control in the immediate postoperative period, decreases blood loss, and decreases the need for rescue narcotics and reversal agents. This simple, inexpensive method provides an effective adjunct to a multimodal approach in improving the postoperative course of primary total knee arthroplasty.

Electrically heated particulate filter preparation methods and systems

DOEpatents

Gonze, Eugene V [Pinckney, MI

2012-01-31

A control system that controls regeneration of a particulate filter is provided. The system generally includes a fuel control module that controls injection of fuel into exhaust that passes through the particulate filter. A regeneration module controls current to the particulate filter to initiate regeneration after the fuel has been injected into the exhaust.

77 FR 53898 - Collection of Information Under Review by Office of Management and Budget

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-04

... following collections of information: 1625-0016, Welding and Hot Work Permits; Posting of Warning Signs.... Title: Welding and Hot Work Permits; Posting of Warning Signs. OMB Control Number: 1625-0016. Type of... facilities and vessels are in compliance with safety standards. A permit must be issued prior to welding or...

40 CFR Appendix A to Subpart Ee of... - States With Approved State Implementation Plan Revisions Concerning Allocations

Code of Federal Regulations, 2010 CFR

2010-07-01

... the permitting authority under § 97.144(b): Indiana Michigan New Jersey Ohio South Carolina Texas [65... permitting authority under § 97.144(a): Indiana Louisiana Michigan New Jersey North Carolina Ohio South Carolina Tennessee Texas (for control periods 2009-2014) West Virginia (for control periods 2009-2014...

In ovo injection of anti-chicken CD25 monoclonal antibodies depletes CD4+CD25+ T cells in chickens.

PubMed

Shanmugasundaram, Revathi; Selvaraj, Ramesh K

2013-01-01

The CD4(+)CD25(+) cells have T regulatory cell properties in chickens. This study investigated the effect of in ovo injection of anti-chicken CD25 monoclonal antibodies (0.5 mg/egg) on CD4(+)CD25(+) cell depletion and on amounts of interleukin-2 mRNA and interferon-γ mRNA in CD4(+)CD25(-) cells posthatch. Anti-chicken CD25 or PBS (control) was injected into 16-d-old embryos. Chicks hatched from eggs injected with anti-chicken CD25 antibodies had a lower CD4(+)CD25(+) cell percentage in the blood until 25 d posthatch. The anti-chicken CD25 antibody injection nearly depleted CD4(+)CD25(+) cells in the blood until 16 d posthatch. At 30 d posthatch, the CD4(+)CD25(+) cell percentage in the anti-CD25-antibody-injected group was comparable with the percentage in the control group. At 16 d posthatch, the anti-chicken CD25 antibody injection decreased CD4(+)CD25(+) cell percentages in the thymus, spleen, and cecal tonsils. Chickens hatched from anti-CD25-antibody-injected eggs had approximately 25% of CD4(+)CD25(+) cells in the cecal tonsils and thymus compared with those in the cecal tonsils and thymus of the control group. The CD4(+)CD25(-) cells from the spleen and cecal tonsils of chicks hatched from anti-chicken-CD25-injected eggs had higher amounts of interferon-γ and interleukin-2 mRNA than CD4(+)CD25(-) cells from the control group. It could be concluded that injecting anti-chicken CD25 antibodies in ovo at 16 d of incubation nearly depleted the CD4(+)CD25(+) cells until 25 d posthatch.

The AAHKS Clinical Research Award: Liposomal Bupivacaine and Periarticular Injection Are Not Superior to Single-Shot Intra-articular Injection for Pain Control in Total Knee Arthroplasty.

PubMed

Jain, Rajesh K; Porat, Manny D; Klingenstein, Greg G; Reid, Jeremy J; Post, Robert E; Schoifet, Scott D

2016-09-01

Intraoperative injections can help reduce early postoperative pain in total knee arthroplasty. We proposed that liposomal bupivacaine would not be superior to more common and cheaper injections. A single-blinded prospective randomized study with 207 consecutive patients was completed. Patients were randomized to treatment with periarticular liposomal bupivacaine injection, periarticular injection of bupivacaine/morphine, or intra-articular injection of bupivacaine/morphine at the conclusion of the procedure. Postoperative visual analog pain scores and narcotic consumption were recorded and analyzed. There was no significant difference in postoperative visual analog pain scores or narcotic consumption among the 3 study groups. Intra-articular injection of bupivacaine and morphine is as effective for postoperative pain control in total knee arthroplasty as periarticular bupivacaine/morphine injection and liposomal bupivacaine. Use of liposomal bupivacaine in total knee arthroplasty is costly and not justified. Copyright © 2016 Elsevier Inc. All rights reserved.

Theoretical model for a thin cylindrical film optical fiber fluorosensor

NASA Technical Reports Server (NTRS)

Egalon, Claudio O.; Rogowski, Robert S.

1992-01-01

The analytical treatment of power efficiency (P(eff) is undertaken for the case of a positively guiding optical fiber with a thin-film source distributed in the core-cladding interface. The approach adopts the exact solution of the cylindrical optical fiber with an infinite cladding to account for differences between the indices of refraction of the core and the cladding. The excitation of low-loss leaky modes by the cladding is ignored, and only the injection by the evanescent field is considered. The formulas permit the analysis of the power-injection efficiency of fibers with arbitrary differences in indices of refraction. P(eff) does not always increase with V number, but rather varies slightly with wavelength and fiber-core radius and varies significantly with the difference in the indices of refraction. The theoretical results of the work are of interest for designing an atomic-O chemical sensor based on evanescent-wave coupling.

DIFMOS - A floating-gate electrically erasable nonvolatile semiconductor memory technology. [Dual Injector Floating-gate MOS

NASA Technical Reports Server (NTRS)

Gosney, W. M.

1977-01-01

Electrically alterable read-only memories (EAROM's) or reprogrammable read-only memories (RPROM's) can be fabricated using a single-level metal-gate p-channel MOS technology with all conventional processing steps. Given the acronym DIFMOS for dual-injector floating-gate MOS, this technology utilizes the floating-gate technique for nonvolatile storage of data. Avalanche injection of hot electrons through gate oxide from a special injector diode in each bit is used to charge the floating gates. A second injector structure included in each bit permits discharge of the floating gate by avalanche injection of holes through gate oxide. The overall design of the DIFMOS bit is dictated by the physical considerations required for each of the avalanche injector types. The end result is a circuit technology which can provide fully decoded bit-erasable EAROM-type circuits using conventional manufacturing techniques.

Control of Citrus Huanglongbing via Trunk Injection of Plant Defense Activators and Antibiotics.

PubMed

Hu, J; Jiang, J; Wang, N

2018-02-01

Citrus huanglongbing (HLB) or greening is a devastating disease of citrus worldwide and no effective control measure is currently available. Plant defense activators environmentally friendly compounds capable of inducing resistance against many plant pathogens. Earlier studies showed that foliar spray of plant defense inducers could slow down HLB disease progress. In this study, eight plant defense activators and three antibiotics were evaluated in three field trials for their effect to control HLB by trunk injection of young and mature sweet orange trees. Results showed that four trunk injections of several activators, including salicylic acid, oxalic acid, acibenzolar-S-methyl, and potassium phosphate, provided significant control of HLB by suppressing 'Candidatus Liberibacter asiaticus' titer and disease progress. Trunk injection of penicillin, streptomycin, and oxytetracycline hydrochloride resulted in excellent control of HLB. In general, antibiotics were more effective in reduction of 'Ca. L. asiaticus' titer and HLB symptom expressions than plant defense activators. These treatments also resulted in increased yield and better fruit quality. Injection of both salicylic acid and acibenzolar-S-methyl led to significant induction of pathogenesis-related (PR) genes PR-1 and PR-2 genes. Meanwhile, injection of either potassium phosphate or oxalic acid resulted in significant induction of PR-2 or PR-15 gene expression, respectively. These results suggested that HLB diseased trees remained inducible for systemic acquired resistance under field conditions. In summary, this study presents information regarding controlling HLB via trunk injection of plant defense activators and antibiotics, which helps citrus growers in decision making regarding developing an effective HLB management program.

Evaluation of a needle social marketing strategy to control HIV among injecting drug users in China.

PubMed

Wu, Zunyou; Luo, Wei; Sullivan, Sheena G; Rou, Keming; Lin, Peng; Liu, Wei; Ming, Zhongqiang

2007-12-01

To evaluate the effectiveness of a needle social marketing strategy to reduce needle sharing and hepatitis C Virus (HCV)/HIV transmission among injecting drug users (IDU) in China. Two-armed, prospective, community-randomized prevention trial. Four counties/townships in Guangxi and Guangdong provinces; one randomized to intervention the other to control in each province. Injecting drug users: 823 (443 intervention, 382 control) at baseline and 852 (415 intervention, 407 control) at the second cross-sectional survey 12 months later. A needle social marketing programme, including promotion of safe injection norms and increased access to clean needles over a 12 month period. Cross sectional surveys at baseline and follow-up compared changes in drug using behaviours and HIV and HCV rates in the intervention and control communities. Needle sharing behaviours were similar in the two groups at baseline (68.4 vs. 67.8%), and dropped significantly to 35.3% in the intervention community and remained relatively stable in the control community (62.3%; P < 0.001). In a subset of cohort of new injectors, the incidence of HCV was significant lower in intervention than in control in both provinces (P < 0.001, P = 0.014) and overall (P < 0.001) but HIV was only significantly lower in intervention in Guangdong (P = 0.011). Needle social marketing can reduce risky injecting behaviour and HIV/HCV transmission among injecting drug users in China and should be expanded.

MERCURY CONTROL IN MUNICIPAL WASTE COMBUSTORS AND COAL-FIRED UTILITIES

EPA Science Inventory

Control of mercury (Hg) emissions from municipal waste combustors (MWCs) and coal-fired utilities has attracted attention due to current and potential regulations. Among several techniques evaluated for Hg control, dry sorbent injection (primarily injection of activated carbon) h...

Evaluation of intracameral injection of ranibizumab and bevacizumab on the corneal endothelium by scanning electron microscopy.

PubMed

Ari, Seyhmus; Nergiz, Yusuf; Aksit, Ihsan; Sahin, Alparslan; Cingu, Kursat; Caca, Ihsan

2015-03-01

To evaluate the effects of intracameral injection of ranibizumab and bevacizumab on the corneal endothelium by scanning electron microscopy (SEM). Twenty-eight female rabbits were randomly divided into four equal groups. Rabbits in groups 1 and 2 underwent intracameral injection of 1 mg/0.1 mL and 0.5 mg/0.05 mL ranibizumab, respectively; group 3 was injected with 1.25 mg/0.05 mL bevacizumab. All three groups were injected with a balanced salt solution (BSS) into the anterior chamber of the left (fellow) eye. None of the rabbits in group 4 underwent an injection. Corneal thickness and intraocular pressure were measured before the injections, on the first day, and in the first month after injection. The rabbits were sacrificed and corneal tissues were excised in the first month after injection. Specular microscopy was used for the corneal endothelial cell count. Endothelial cell density was assessed and comparisons drawn between the groups and the control. Micrographs were recorded for SEM examination. The structure of the corneal endothelial cells, the junctional area of the cell membrane, the distribution of microvillus, and the cell morphology of the eyes that underwent intracameral injection of vascular endothelial growth factor (VEGF), BSS, and the control group were compared. Corneal thickness and intraocular pressure were not significantly different between the groups that underwent anti-VEGF or BSS injection and the control group on the first day and in the first month of injection. The corneal endothelial cell count was significantly diminished in all three groups; predominantly in group 1 and 2 (P<0.05). The SEM examination revealed normal corneal endothelial histology in group 3 and the control group. Eyes in group 1 exhibited indistinctness of corneal endothelial cell borders, microvillus loss in the luminal surface, excessive blebbing, and disintegration of intercellular junctions. In group 2, the cell structure of the corneal endothelium and intercellular junctions were normal. However, a relative reduction was observed in the microvillus density of endothelial cells. Although eyes in group 3 were morphologically similar to fellow eyes and the control group, disarrangement in endothelial cell borders was evident. The SEM examination pointed out deterioration in endothelial cell morphology after intracameral injection of 1 and 0.5 mg ranizumab. However, the effects of intracameral bevacizumab injection on corneal endothelial cells were similar to those found in fellow eyes and the control group. Further large-scale studies that examine the cellular changes by transmission electron microscopy are required to support the results of the present study that evaluates the structural changes in endothelial cells by SEM.

Diphenhydramine Injection

MedlinePlus

... or along with other medications to control abnormal movements in people who have Parkinsonian syndrome (a disorder of the nervous system that causes difficulties with movement, muscle control, and balance). Diphenhydramine injection should not ...

Flow monitoring and control system for injection wells

DOEpatents

Corey, John C.

1993-01-01

A system for monitoring and controlling the injection rate of fluid by an injection well of an in-situ remediation system for treating a contaminated groundwater plume. The well is fitted with a gated insert, substantially coaxial with the injection well. A plurality of openings, some or all of which are equipped with fluid flow sensors and gates, are spaced along the insert. The gates and sensors are connected to a surface controller. The insert may extend throughout part of, or substantially the entire length of the injection well. Alternatively, the insert may comprise one or more movable modules which can be positioned wherever desired along the well. The gates are opened part-way at the start of treatment. The sensors monitor and display the flow rate of fluid passing through each opening on a controller. As treatment continues, the gates are opened to increase flow in regions of lesser flow, and closed to decrease flow in regions of greater flow, thereby approximately equalizing the amount of fluid reaching each part of the plume.

Flow monitoring and control system for injection wells

DOEpatents

Corey, J.C.

1993-02-16

A system for monitoring and controlling the injection rate of fluid by an injection well of an in-situ remediation system for treating a contaminated groundwater plume. The well is fitted with a gated insert, substantially coaxial with the injection well. A plurality of openings, some or all of which are equipped with fluid flow sensors and gates, are spaced along the insert. The gates and sensors are connected to a surface controller. The insert may extend throughout part of, or substantially the entire length of the injection well. Alternatively, the insert may comprise one or more movable modules which can be positioned wherever desired along the well. The gates are opened part-way at the start of treatment. The sensors monitor and display the flow rate of fluid passing through each opening on a controller. As treatment continues, the gates are opened to increase flow in regions of lesser flow, and closed to decrease flow in regions of greater flow, thereby approximately equalizing the amount of fluid reaching each part of the plume.

Lacosamide Injection

MedlinePlus

Lacosamide injection is used in combination with other medications to control certain types of seizures in people who cannot take oral medications. Lacosamide injection is in a class of medications called ...

Hurricane Recovery and Ecological Resilience: Measuring the Impacts of Wetland Alteration Post Hurricane Ike on the Upper TX Coast

NASA Astrophysics Data System (ADS)

Reja, Md Y.; Brody, Samuel D.; Highfield, Wesley E.; Newman, Galen D.

2017-12-01

Recovery after hurricane events encourages new development activities and allows reconstruction through the conversion of naturally occurring wetlands to other land uses. This research investigates the degree to which hurricane recovery activities in coastal communities are undermining the ability of these places to attenuate the impacts of future storm events. Specifically, it explores how and to what extent wetlands are being affected by the CWA Section 404 permitting program in the context of post-Hurricane Ike 2008 recovery. Wetland alteration patterns are examined by selecting a control group (Aransas and Brazoria counties with no hurricane impact) vs. study group (Chambers and Galveston counties with hurricane impact) research design with a pretest-posttest measurement analyzing the variables such as permit types, pre-post Ike permits, land cover classes, and within-outside the 100-year floodplain. Results show that permitting activities in study group have increased within the 100-year floodplain and palustrine wetlands continue to be lost compare to the control group. Simultaneously, post-Ike individual and nationwide permits increased in the Hurricane Ike impacted area. A binomial logistic regression model indicated that permits within the study group, undeveloped land cover class, and individual and nationwide permit type have a substantial effect on post-Ike permits, suggesting that post-Ike permits have significant impact on wetland losses. These findings indicate that recovery after the hurricane is compromising ecological resiliency in coastal communities. The study outcome may be applied to policy decisions in managing wetlands during a long-term recovery process to maintain natural function for future flood mitigation.

Hurricane Recovery and Ecological Resilience: Measuring the Impacts of Wetland Alteration Post Hurricane Ike on the Upper TX Coast.

PubMed

Reja, Md Y; Brody, Samuel D; Highfield, Wesley E; Newman, Galen D

2017-12-01

Recovery after hurricane events encourages new development activities and allows reconstruction through the conversion of naturally occurring wetlands to other land uses. This research investigates the degree to which hurricane recovery activities in coastal communities are undermining the ability of these places to attenuate the impacts of future storm events. Specifically, it explores how and to what extent wetlands are being affected by the CWA Section 404 permitting program in the context of post-Hurricane Ike 2008 recovery. Wetland alteration patterns are examined by selecting a control group (Aransas and Brazoria counties with no hurricane impact) vs. study group (Chambers and Galveston counties with hurricane impact) research design with a pretest-posttest measurement analyzing the variables such as permit types, pre-post Ike permits, land cover classes, and within-outside the 100-year floodplain. Results show that permitting activities in study group have increased within the 100-year floodplain and palustrine wetlands continue to be lost compare to the control group. Simultaneously, post-Ike individual and nationwide permits increased in the Hurricane Ike impacted area. A binomial logistic regression model indicated that permits within the study group, undeveloped land cover class, and individual and nationwide permit type have a substantial effect on post-Ike permits, suggesting that post-Ike permits have significant impact on wetland losses. These findings indicate that recovery after the hurricane is compromising ecological resiliency in coastal communities. The study outcome may be applied to policy decisions in managing wetlands during a long-term recovery process to maintain natural function for future flood mitigation.

Advanced injection seeder for various applications: form LIDARs to supercontinuum sources

NASA Astrophysics Data System (ADS)

Grzes, Pawel

2017-12-01

The paper describes an injection seeder driver (prototype) for a directly modulated semiconductor laser diode. The device provides adjustable pulse duration and repetition frequency to shape an output signal. A temperature controller stabilizes a laser diode spectrum. Additionally, to avoid a back oscillation, redundant power supply holds a generation until next stages shut down. Low EMI design and ESD protection guarantee stable operation even in a noisy environment. The controller is connected to the PC via USB and parameters of the pulse are digitally controlled through a graphical interface. The injection seeder controller can be used with a majority of commercially available laser diodes. In the experimental setup a telecommunication DFB laser with 4 GHz bandwidth was used. It allows achieving subnanosecond pulses generated at the repetition rate ranging from 1 kHz to 50 MHz. The developed injection seeder controller with a proper laser diode can be used in many scientific, industrial and medical applications.

Al2O3-ZrO2 Finely Structured Multilayer Architectures from Suspension Plasma Spraying

NASA Astrophysics Data System (ADS)

Tingaud, Olivier; Montavon, Ghislain; Denoirjean, Alain; Coudert, Jean-François; Rat, Vincent; Fauchais, Pierre

2010-01-01

Suspension plasma spraying (SPS) is an alternative to conventional atmospheric plasma spraying (APS) aiming at manufacturing thinner layers (i.e., 10-100 μm) due to the specific size of the feedstock particles, from a few tens of nanometers to a few micrometers. The staking of lamellae and particles, which present a diameter ranging from 0.1 to 2.0 μm and an average thickness from 20 to 300 nm, permits to manufacture finely structured layers. Moreover, it appears as a versatile process able to manufacture different coating architectures according to the operating parameters (suspension properties, injection configuration, plasma properties, spray distance, torch scan velocity, scanning step, etc.). However, the different parameters controlling the properties of the coating, and their interdependences, are not yet fully identified. Thus, the aim of this paper is, on the one hand, to better understand the influence of operating parameters on the coating manufacturing mechanisms (in particular, the plasma gas mixture effect) and, on the other hand, to produce Al2O3-ZrO2 finely structured layers with large varieties of architectures. For this purpose, a simple theoretical model was used to describe the plasma torch operating conditions at the nozzle exit, based on experimental data (mass enthalpy, arc current intensity, thermophysical properties of plasma forming gases, etc.) and the influences of the spray parameters were determined by mean of the study of sizes and shapes of spray beads. The results enabled then to reach a better understanding of involved phenomena and their interactions on the final coating architectures permitting to manufacture several types of microstructures.

Distribution of effluent injected into the Boulder Zone of the Floridan aquifer system at the North District Wastewater Treatment Plant, southeastern Florida, 1997–2011

USGS Publications Warehouse

King, Jeffrey N.; Decker, Jeremy D.

2018-02-09

Nonhazardous, secondarily treated, domestic wastewater (effluent) has been injected about 1 kilometer below land surface into the Boulder Zone of the Floridan aquifer system at the North District Wastewater Treatment Plant in southeastern Florida. The Boulder Zone contains saline, nonpotable water. Effluent transport out of the injection zone is a risk of underground effluent injection. At the North District Wastewater Treatment Plant, injected effluent was detected outside the Boulder Zone. The U.S. Geological Survey, in cooperation with Miami-Dade Water and Sewer Department, investigated effluent transport from the Boulder Zone to overlying permeable zones in the Floridan aquifer system.One conceptual model is presented to explain the presence of effluent outside of the injection zone in which effluent injected into the Boulder Zone was transported to the Avon Park permeable zone, forced by buoyancy and injection pressure. In this conceptual model, effluent injected primarily into the Boulder Zone reaches a naturally occurring feature (a karst-collapse structure) near an injection well, through which the effluent is transported vertically upward to the uppermost major permeable zone of the Lower Floridan aquifer. The effluent is then transported laterally through the uppermost major permeable zone of the Lower Floridan aquifer to another naturally occurring feature northwest of the North District Wastewater Treatment Plant, through which it is then transported vertically upward into the Avon Park permeable zone. In addition, a leak within a monitoring well, between monitoring zones, allowed interflow between the Avon Park permeable zone and the Upper Floridan aquifer. A groundwater flow and effluent transport simulation of the hydrogeologic system at the North District Wastewater Treatment Plant, based on the hypothesized and non-unique conceptualization of the subsurface hydrogeology and flow system, generally replicated measured effluent constituent concentration trends. The model was calibrated to match observed concentration trends for total ammonium (NH4+) and total dissolved solids.The investigation qualitatively indicates that fractures, karst-collapse structures, faults, or other hydrogeologic features may permit effluent injected into the Boulder Zone to be transported to overlying permeable zones in the Floridan aquifer system. These findings, however, are qualitative because the locations of transport pathways that might exist from the Boulder Zone to the Avon Park permeable zone are largely unknown.

Protecting Against Damage from Refraction of High Power Microwaves in the DIII-D Tokamak

NASA Astrophysics Data System (ADS)

Lohr, John; Brambila, Rigo; Cengher, Mirela; Chen, Xi; Gorelov, Yuri; Grosnickle, William; Moeller, Charles; Ponce, Dan; Prater, Ron; Torrezan, Antonio; Austin, Max; Doyle, Edward; Hu, Xing; Dormier, Calvin

2017-07-01

Several new protective systems are being installed on the DIII D tokamak to increase the safety margins for plasma operations with injected ECH power at densities approaching cutoff. Inadvertent overdense operation has previously resulted in reflection of an rf beam back into a launcher causing extensive arcing and melt damage on one waveguide line. Damage to microwave diagnostics, which are located on the same side of the tokamak as the ECH launchers, also has occurred. Developing a reliable microwave based interlock to protect the many vulnerable systems in DIII-D has proved to be difficult. Therefore, multiple protective steps have been taken to reduce the risk of damage in the future. Among these is a density interlock generated by the plasma control system, with setpoint determined by the ECH operators based on rf beam trajectories and plasma parameters. Also installed are enhanced video monitoring of the launchers, and an ambient light monitor on each of the waveguide systems, along with a Langmuir probe at the mouth of each launcher. Versatile rf monitors, measuring forward and reflected power in addition to the mode content of the rf beams, have been installed as the last miter bends in each waveguide line. As these systems are characterized, they are being incorporated in the interlock chains, which enable the ECH injection permits. The diagnostics most susceptible to damage from the ECH waves have also been fitted with a variety of protective devices including stripline filters, thin resonant notch filters tuned to the 110 GHz injected microwave frequency, blazed grating filters and shutters. Calculations of rf beam trajectories in the plasmas are performed using the TORAY ray tracing code with input from kinetic profile diagnostics. Using these calculations, strike points for refracted beams on the vacuum vessel are calculated, which allows evaluation of the risk of damage to sensitive diagnostics and hardware.

Protecting against damage from refraction of high power microwaves in the DIII-D tokamak

DOE PAGES

Lohr, John; Brambila, Rigo; Cengher, Mirela; ...

2017-07-24

Here, several new protective systems are being installed on the DIII D tokamak to increase the safety margins for plasma operations with injected ECH power at densities approaching cutoff. Inadvertent overdense operation has previously resulted in reflection of an rf beam back into a launcher causing extensive arcing and melt damage on one waveguide line. Damage to microwave diagnostics, which are located on the same side of the tokamak as the ECH launchers, also has occurred. Developing a reliable microwave based interlock to protect the many vulnerable systems in DIII-D has proved to be difficult. Therefore, multiple protective steps havemore » been taken to reduce the risk of damage in the future. Among these is a density interlock generated by the plasma control system, with setpoint determined by the ECH operators based on rf beam trajectories and plasma parameters. Also installed are enhanced video monitoring of the launchers, and an ambient light monitor on each of the waveguide systems, along with a Langmuir probe at the mouth of each launcher. Versatile rf monitors, measuring forward and reflected power in addition to the mode content of the rf beams, have been installed as the last miter bends in each waveguide line. As these systems are characterized, they are being incorporated in the interlock chains, which enable the ECH injection permits. The diagnostics most susceptible to damage from the ECH waves have also been fitted with a variety of protective devices including stripline filters, thin resonant notch filters tuned to the 110 GHz injected microwave frequency, blazed grating filters and shutters. Calculations of rf beam trajectories in the plasmas are performed using the TORAY ray tracing code with input from kinetic profile diagnostics. Using these calculations, strike points for refracted beams on the vacuum vessel are calculated, which allows evaluation of the risk of damage to sensitive diagnostics and hardware.« less

Protecting against damage from refraction of high power microwaves in the DIII-D tokamak

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lohr, John; Brambila, Rigo; Cengher, Mirela

Here, several new protective systems are being installed on the DIII D tokamak to increase the safety margins for plasma operations with injected ECH power at densities approaching cutoff. Inadvertent overdense operation has previously resulted in reflection of an rf beam back into a launcher causing extensive arcing and melt damage on one waveguide line. Damage to microwave diagnostics, which are located on the same side of the tokamak as the ECH launchers, also has occurred. Developing a reliable microwave based interlock to protect the many vulnerable systems in DIII-D has proved to be difficult. Therefore, multiple protective steps havemore » been taken to reduce the risk of damage in the future. Among these is a density interlock generated by the plasma control system, with setpoint determined by the ECH operators based on rf beam trajectories and plasma parameters. Also installed are enhanced video monitoring of the launchers, and an ambient light monitor on each of the waveguide systems, along with a Langmuir probe at the mouth of each launcher. Versatile rf monitors, measuring forward and reflected power in addition to the mode content of the rf beams, have been installed as the last miter bends in each waveguide line. As these systems are characterized, they are being incorporated in the interlock chains, which enable the ECH injection permits. The diagnostics most susceptible to damage from the ECH waves have also been fitted with a variety of protective devices including stripline filters, thin resonant notch filters tuned to the 110 GHz injected microwave frequency, blazed grating filters and shutters. Calculations of rf beam trajectories in the plasmas are performed using the TORAY ray tracing code with input from kinetic profile diagnostics. Using these calculations, strike points for refracted beams on the vacuum vessel are calculated, which allows evaluation of the risk of damage to sensitive diagnostics and hardware.« less

Optimal design strategy of switching converters employing current injected control

NASA Astrophysics Data System (ADS)

Lee, F. C.; Fang, Z. D.; Lee, T. H.

1985-01-01

This paper analyzes a buck/boost regulator employing current-injected control (CIC). It reveals the complex interactions between the dc loop and the current-injected loop and underlines the fundamental principle that governs the loop gain determination. Three commonly used compensation techniques are compared. The integral and lead/lag compensation are shown to be most desirable for performance optimization and stability.

Refinery siting workbook: appendices C to O

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Applicable laws and permits available for the selection and building of petroleum refineries are enclosed. A glossary of pertinent terms is also included. References related to the National Environmental Policy Act, the Clean Air Act, the Federal Water Pollution Control Act, Resource Conservation and Recovery Act, Toxic Substance Control Act, and Wetlands and Coastal Zone are included. Permit information is also presented. (DC)

Simulation of Liquid Injection Thrust Vector Control for Mars Ascent Vehicle

NASA Technical Reports Server (NTRS)

Gudenkauf, Jared

2017-01-01

The Jet Propulsion Laboratory is currently in the initial design phase for a potential Mars Ascent Vehicle; which will be landed on Mars, stay on the surface for period of time, collect samples from the Mars 2020 rover, and then lift these samples into orbit around Mars. The engineers at JPL have down selected to a hybrid wax-based fuel rocket using a liquid oxidizer based on nitrogen tetroxide, or a Mixed Oxide of Nitrogen. To lower the gross lift-off mass of the vehicle the thrust vector control system will use liquid injection of the oxidizer to deflect the thrust of the main nozzle instead of using a gimbaled nozzle. The disadvantage of going with the liquid injection system is the low technology readiness level with a hybrid rocket. Presented in this paper is an effort to simulate the Mars Ascent Vehicle hybrid rocket nozzle and liquid injection thrust vector control system using the computational fluid dynamic flow solver Loci/Chem. This effort also includes determining the sensitivity of the thrust vector control system to a number of different design variables for the injection ports; including axial location, number of adjacent ports, injection angle, and distance between the ports.

Multiplexed detection of nitrate and nitrite for capillary electrophoresis with an automated device for high injection efficiency.

PubMed

Gao, Leyi; Patterson, Eric E; Shippy, Scott A

2006-02-01

A simple automated nanoliter scale injection device which allows for reproducible 5 nL sample injections from samples with a volume of <1 microL is successfully used for conventional capillary electrophoresis (CE) and Hadamard transform (HT) CE detection. Two standard fused silica capillaries are assembled axially through the device to function as an injection and a separation capillary. Sample solution is supplied to the injection capillary using pressure controlled with a solenoid valve. Buffer solution flows gravimetrically by the junction of the injection and separation capillaries and is also gated with a solenoid valve. Plugs of sample are pushed into the space between the injection and separation capillaries for electrokinectic injection. To evaluate the performance of the injection device, several optimizations are performed including the influence of flow rates, the injected sample volume and the control of the buffer transverse flow on the overall sensitivity. The system was then applied to HT-CE-UV detection for the signal-to-noise ratio (S/N) improvement of the nitric oxide (NO) metabolites, nitrite and nitrate. In addition, signal averaging was performed to explore the possibility of greater sensitivity enhancements compared to single injections.

Study of Methylene Blue Ototoxicity in the Guinea Pig.

PubMed

Belhassen, Sarah; Alzahrani, Musaed; Nader, Marc-Elie; Gaboury, Louis; Saliba, Issam

2017-11-01

Methylene blue is widely used in the medical field, especially as a blue dye for staining. It is also used as a photosensitizing agent in antimicrobial photodynamic therapy, which once photoactivated is effective for the eradication of several multi-resistant bacteria. The objective of this study was to investigate the ototoxic potential of methylene blue and precise its use in otology. It was a prospective animal study performed on guinea pigs in our tertiary medical center. We divided the animals into two groups: an experimental group and a control group, who underwent a series of three intratympanic (IT) injections. In the control group (n = 10), they received injections of gentamicin in one ear (positive control) and normal saline in the contralateral ear (negative control). The experimental group (n = 10) received injections of methylene blue in one ear, compared to injections of normal saline in the contralateral ear. We conducted auditory-evoked brainstem response (ABR) before and 1 week after the injection series. Once this is completed, the cochlea was dissected and caspase-3 was analyzed by immunohistochemistry. The mean difference of hearing loss in the methylene blue group compared to normal saline was 1.50 dB, and it was not shown to be statistically significant (P = 0.688). For the positive control group, which received IT injections of gentamicin, the mean threshold of hearing loss difference for all the frequencies combined was 66.25 dB (P < 0.001). Furthermore, uptake of caspase-3 by immunohistochemistry (apoptotic marker) was negative in our group, which received injections of methylene blue. In light of our results, IT injections of methylene blue did not demonstrate an ototoxic potential. We recommend further studies to precise its use in the otologic field.

Study of Methylene Blue Ototoxicity in the Guinea Pig

PubMed Central

Belhassen, Sarah; Alzahrani, Musaed; Nader, Marc-Elie; Gaboury, Louis; Saliba, Issam

2017-01-01

Background Methylene blue is widely used in the medical field, especially as a blue dye for staining. It is also used as a photosensitizing agent in antimicrobial photodynamic therapy, which once photoactivated is effective for the eradication of several multi-resistant bacteria. The objective of this study was to investigate the ototoxic potential of methylene blue and precise its use in otology. Methods It was a prospective animal study performed on guinea pigs in our tertiary medical center. We divided the animals into two groups: an experimental group and a control group, who underwent a series of three intratympanic (IT) injections. In the control group (n = 10), they received injections of gentamicin in one ear (positive control) and normal saline in the contralateral ear (negative control). The experimental group (n = 10) received injections of methylene blue in one ear, compared to injections of normal saline in the contralateral ear. We conducted auditory-evoked brainstem response (ABR) before and 1 week after the injection series. Once this is completed, the cochlea was dissected and caspase-3 was analyzed by immunohistochemistry. Results The mean difference of hearing loss in the methylene blue group compared to normal saline was 1.50 dB, and it was not shown to be statistically significant (P = 0.688). For the positive control group, which received IT injections of gentamicin, the mean threshold of hearing loss difference for all the frequencies combined was 66.25 dB (P < 0.001). Furthermore, uptake of caspase-3 by immunohistochemistry (apoptotic marker) was negative in our group, which received injections of methylene blue. Conclusion In light of our results, IT injections of methylene blue did not demonstrate an ototoxic potential. We recommend further studies to precise its use in the otologic field. PMID:29038666

Automatic and remote controlled ictal SPECT injection for seizure focus localization by use of a commercial contrast agent application pump.

PubMed

Feichtinger, Michael; Eder, Hans; Holl, Alexander; Körner, Eva; Zmugg, Gerda; Aigner, Reingard; Fazekas, Franz; Ott, Erwin

2007-07-01

In the presurgical evaluation of patients with partial epilepsy, the ictal single photon emission computed tomography (SPECT) is a useful noninvasive diagnostic tool for seizure focus localization. To achieve optimal SPECT scan quality, ictal tracer injection should be carried out as quickly as possible after the seizure onset and under highest safety conditions possible. Compared to the commonly used manual injection, an automatic administration of the radioactive tracer may provide higher quality standards for this procedure. In this study, therefore, we retrospectively analyzed efficiency and safety of an automatic injection system for ictal SPECT tracer application. Over a 31-month period, 26 patients underwent ictal SPECT by use of an automatic remote-controlled injection pump originally designed for CT-contrast agent application. Various factors were reviewed, including latency of ictal injection, radiation safety parameters, and ictal seizure onset localizing value. Times between seizure onset and tracer injection ranged between 3 and 48 s. In 21 of 26 patients ictal SPECT supported the localization of the epileptogenic focus in the course of the presurgical evaluation. In all cases ictal SPECT tracer injection was performed with a high degree of safety to patients and staff. Ictal SPECT by use of a remote-controlled CT-contrast agent injection system provides a high scan quality and is a safe and confirmatory presurgical evaluation technique in the epilepsy-monitoring unit.

40 CFR 144.60 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... INJECTION CONTROL PROGRAM Financial Responsibility: Class I Hazardous Waste Injection Wells § 144.60... existing and new Class I Hazardous waste injection wells, except as provided otherwise in this section. ...

A PDP-15 to industrial-14 interface at the Lewis Research Center's cyclotron

NASA Technical Reports Server (NTRS)

Kebberly, F. R.; Leonard, R. F.

1977-01-01

An interface (hardware and software) was built which permits the loading, monitoring, and control of a digital equipment industrial-14/30 programmable controller by a PDP-15 computer. The interface utilizes the serial mode for data transfer to and from the controller, so that the required hardware is essentially that of a teletype unit except for the speed of transmission. Software described here permits the user to load binary paper tape, read or load individual controller memory locations, and if desired turn controller outputs on and off directly from the computer.

Micellar electrokinetic chromatography and capillary electrochromatography of nitroaromatic explosives in seawater.

PubMed

Giordano, Braden C; Copper, Christine L; Collins, Greg E

2006-02-01

The ability to separate nitroaromatic and nitramine explosives in seawater sample matrices is demonstrated using both MEKC and CEC. While several capillary-based separations exist for explosives, none address direct sampling from seawater, a sample matrix of particular interest in the detection of undersea mines. Direct comparisons are made between MEKC and CEC in terms of sensitivity and separation efficiency for the analysis of 14 explosives and explosive degradation products in seawater and diluted seawater. The use of high-salt stacking with MEKC results, on average, in a three-fold increase in the number of theoretical plates, and nearly double resolution for samples prepared in 25% seawater. By taking advantage of long injection times in conjunction with stacking, detection limits down to sub mg/L levels are attainable; however, resolution is sacrificed. CEC of explosive mixtures using sol-gels prepared from methyltrimethoxysilane does not perform as well as MEKC in terms of resolving power, but does permit extended injection times for concentrating analyte onto the head of the separation column with little or no subsequent loss in resolution. Electrokinetic injections of 8 min at high voltage allow for detection limits of explosives below 100 microg/L.

Termination of aquired and natural immunological tolerance with specific complexes

PubMed Central

1975-01-01

It was possible to terminate the induced unresponsive state to bovine serum albumin (BSA) and the natural unresponsive state to autologous thyroglobulin in rabbits (RTg) by immunization with complexes composed of heterologous cross-reacting antibody and the tolerated antigens. The unresponsive state was terminated in rabbits made unresponsive by neonatal injections of BSA and then 3 mo later injected with complexes composed of BSA and guinea pig antihuman serum albumin. This termination was manifested by the presence of anti-BSA plaque-forming cells. Similarly, the natural unresponsive state was terminated in adult rabbits injected with complexes between RTg and guinea pig antibovine thyroglobulin (BTg) in that thyroid lesions and circulating anti-RTg were produced. The results can be best explained by the presence of unresponsive T cells and competent B cells, where the guinea pig gamma globulin (antibody) activates T cells specific for the guinea pig gamma globulin portion of the complexes and thus permits stimulation of B cells competent to the exposed determinants of the tolerated (BSA or RTg) portion of the complexes. The detailed mechanism for the activation of B cells in tolerant animals is discussed. PMID:1095680

Permeation of antigen protein-conjugated nanoparticles and live bacteria through microneedle-treated mouse skin

PubMed Central

Kumar, Amit; Li, Xinran; Sandoval, Michael A; Rodriguez, B Leticia; Sloat, Brian R; Cui, Zhengrong

2011-01-01

Background: The present study was designed to evaluate the extent to which pretreatment with microneedles can enhance skin permeation of nanoparticles in vitro and in vivo. Permeation of live bacteria, which are physically nanoparticles or microparticles, through mouse skin pretreated with microneedles was also studied to evaluate the potential risk of microbial infection. Methods and results: It was found that pretreatment of mouse skin with microneedles allowed permeation of solid lipid nanoparticles, size 230 nm, with ovalbumin conjugated on their surface. Transcutaneous immunization in a mouse skin area pretreated with microneedles with ovalbumin nanoparticles induced a stronger antiovalbumin antibody response than using ovalbumin alone. The dose of ovalbumin antigen determined whether microneedle-mediated transcutaneous immunization with ovalbumin nanoparticles induced a stronger immune response than subcutaneous injection of the same ovalbumin nanoparticles. Microneedle treatment permitted skin permeation of live Escherichia coli, but the extent of the permeation was not greater than that enabled by hypodermic injection. Conclusion: Transcutaneous immunization on a microneedle-treated skin area with antigens carried by nanoparticles can potentially induce a strong immune response, and the risk of bacterial infection associated with microneedle treatment is no greater than that with a hypodermic injection. PMID:21753877

Biosynthesis and secretion of catalytically active acetylcholinesterase in Xenopus oocytes microinjected with mRNA from rat brain and from Torpedo electric organ.

PubMed

Soreq, H; Parvari, R; Silman, I

1982-02-01

A novel technique was developed for monitoring the level of the mRNA species that direct the synthesis of acetylcholinesterase (AcChoEase; acetylcholine acetylhydrolase, EC 3.1.1.7), using microinjected Xenopus oocytes as a translation system. When injected with poly(A)-containing RNA from whole rat brain or rat cerebellum and from electric organ of Torpedo ocellata, Xenopus oocytes synthesize and secrete catalytically active cholinesterase. The newly synthesized enzyme, which is mostly secreted into the oocytes incubation medium, appears to be primarily AcChoEase because it is inhibited by the specific inhibitor BW 284C51. The new enzymatic activity can be detected after injection of as little as 12.5 ng of poly(A)-containing RNA per oocyte, and there is a linear dependence of the oocytes' ability to form AcChoEase on the amount of injected RNA. The AcChoEase mRNA displays a tau 1/2 of about 10 +/- 3 hr in injected oocytes. The abundance of AcChoEase mRNA in the total nonfractionated mRNA injected was calculated to be ca. 1 x 10(-5), a value similar to the level of AcChoEase protein determined in rat brain. The combination of the high turnover number of AcChoEase, the efficiency of the oocyte system, and the sensitivity of the assay used thus permit the accurate monitoring of the scarce mRNA species that direct the synthesis of this enzyme.

Design and development of a direct injection system for cryogenic engines

NASA Astrophysics Data System (ADS)

Mutumba, Angela; Cheeseman, Kevin; Clarke, Henry; Wen, Dongsheng

2018-04-01

The cryogenic engine has received increasing attention due to its promising potential as a zero-emission engine. In this study, a new robust liquid nitrogen injection system was commissioned and set up to perform high-pressure injections into an open vessel. The system is used for quasi-steady flow tests used for the characterisation of the direct injection process for cryogenic engines. An electro-hydraulic valve actuator provides intricate control of the valve lift, with a minimum cycle time of 3 ms and a frequency of up to 20 Hz. With additional sub-cooling, liquid phase injections from 14 to 94 bar were achieved. Results showed an increase in the injected mass with the increase in pressure, and decrease in temperature. The injected mass was also observed to increases linearly with the valve lift. Better control of the injection process, minimises the number of variables, providing more comparable and repeatable sets of data. Implications of the results on the engine performance were also discussed.

Impact of Azimuthally Controlled Fluidic Chevrons on Jet Noise

NASA Technical Reports Server (NTRS)

Henderson, Brenda S.; Norum, Thomas D.

2008-01-01

The impact of azimuthally controlled air injection on broadband shock noise and mixing noise for single and dual stream jets was investigated. The single stream experiments focused on noise reduction for low supersonic jet exhausts. Dual stream experiments included high subsonic core and fan conditions and supersonic fan conditions with transonic core conditions. For the dual stream experiments, air was injected into the core stream. Significant reductions in broadband shock noise were achieved in a single jet with an injection mass flow equal to 1.2% of the core mass flow. Injection near the pylon produced greater broadband shock noise reductions than injection at other locations around the nozzle periphery. Air injection into the core stream did not result in broadband shock noise reduction in dual stream jets. Fluidic injection resulted in some mixing noise reductions for both the single and dual stream jets. For subsonic fan and core conditions, the lowest noise levels were obtained when injecting on the side of the nozzle closest to the microphone axis.

Safe injection practice among health care workers, Gharbiya, Egypt.

PubMed

Ismail, Nanees A; Aboul Ftouh, Aisha M; El Shoubary, Waleed H

2005-01-01

A cross-sectional study was conducted in 25 health care facilities in Gharbiya governorate to assess safe injection practices among health care workers (HCWs). Two questionnaires, one to collect information about administrative issues related to safe injection and the other to collect data about giving injections, exposure to needle stick injuries, hepatitis B vaccination status and safe injection training. Practices of injections were observed using a standardized checklist. The study revealed that there was lack of both national and local infection control policies and lack of most of the supplies needed for safe injection practices. Many safe practices were infrequent as proper needle manipulation before disposal (41%), safe needle disposal (47.5%), reuse of used syringe & needle (13.2%) and safe syringe disposal (0%). Exposure to needle stick injuries were common among the interviewed HCWs (66.2%) and hand washing was the common post exposure prophylaxis measure (63.4%). Only 11.3% of HCWs had full course hepatitis B vaccination. Infection control -including safe injections- training programs should be afforded to all HCWs.

Observation of a Distinct Transition in Transport Response to Injection Stress in the Floridan Aquifer System, Southeastern Florida, U.S.A

NASA Astrophysics Data System (ADS)

King, J. N.; Cunningham, K. J.; Foster, A. L.

2011-12-01

The Miami-Dade Water and Sewer Department (MDWASD) injects effluent approximately one km below land surface into the Boulder Zone (BZ) at the North District Wastewater Treatment Plant (NDWWTP). The BZ is highly conductive and composed of fractured dolomite. MDWASD monitors upward effluent migration 450 m below land surface in the Avon Park Permeable Zone (APPZ). The BZ and APPZ---units within the Floridan aquifer system---are separated by a series of inter-bedded aquifers and leaky confining units with hydraulic conductivities that are orders of magnitude smaller than the BZ. MDWASD injected effluent at the NDWWTP during two distinct periods: (1) July 1997 to September 1999, and (2) August 2004 to January 2011. No effluent was injected between October 1999 and July 2004. A few months after the July 1997 injection, MDWASD observed effluent constituents in the APPZ (Figure 1). Some confinement bypass feature permits effluent constituents to be transported from the BZ to the APPZ. Bypass features may include poorly-cased wells, or natural conduits such as fractures, faults, or karst collapse systems. It is possible to describe confinement bypass features with conductance KA/L, where K is hydraulic conductivity, A is cross-sectional area, and L is length. MDWASD observed a distinct transition in the transport response to injection stress of total dissolved solids (TDS) concentration in the APPZ. The conductance required to describe early system response (1997-1999) is one order-of-magnitude larger than the conductance required to describe late system response (2004-2011). Hypotheses to explain transient conductance include clogging of bypass features by some geochemical or biological process that results from the mixing of effluent with groundwater; dissolution or precipitation; or changes in bypass-feature geometry forced by cyclical changes in aquifer-fluid pressure associated with injection. Hypotheses may be tested with geochemical analyses, tracer tests, hydraulic tomography, or microseismic monitoring.

Injection of new psychoactive substance snow blow associated with recently acquired HIV infections among homeless people who inject drugs in Dublin, Ireland, 2015.

PubMed

Giese, Coralie; Igoe, Derval; Gibbons, Zorina; Hurley, Caroline; Stokes, Siobhan; McNamara, Sinead; Ennis, Orla; O'Donnell, Kate; Keenan, Eamon; De Gascun, Cillian; Lyons, Fiona; Ward, Mary; Danis, Kostas; Glynn, Ronan; Waters, Allison; Fitzgerald, Margaret

2015-01-01

In February 2015, an outbreak of recently acquired HIV infections among people who inject drugs (PWID) was identified in Dublin, following similar outbreaks in Greece and Romania in 2011. We compared drug and risk behaviours among 15 HIV cases and 39 controls. Injecting a synthetic cathinone, snow blow, was associated with recent HIV infection (AOR: 49; p=0.003). Prevention and control efforts are underway among PWID in Dublin, but may also be needed elsewhere in Europe.

Tumor detection in mice by measurement of fluorescence decay time matrices

NASA Astrophysics Data System (ADS)

Cubeddu, R.; Pifferi, A.; Taroni, P.; Valentini, G.; Canti, G.

1995-12-01

An intensified CCD video camera has been used to measure the spatial distribution of the fluorescence decay time in tumor-bearing mice sensitized with hematoporphyrin derivative. Mice were injected with five doses of sensitizer, ranging from 0.1 to 10 mg / kg body weight. For any drug dose the decay time of the exogenous fluorescence in the tumor is always significantly longer than in normal tissues. The image created by associating a gray-shade scale to the decay time matrix of each mouse permits a reliable and precise detection of the neoplasia.

Contingency power concepts for helicopter turboshaft engine

NASA Technical Reports Server (NTRS)

Hirschkron, R.; Davis, R. H.; Goldstein, D. N.; Haynes, J. F.; Gauntner, J. W.

1984-01-01

Twin helicopter engines are often sized by power requirement of safe mission completion after the failure of one of the two engines. This study was undertaken for NASA Lewis by General Electric Co. to evaluate the merits of special design features to provide a 2-1/2 minute Contingency Power rating, permitting an engine size reduction. The merits of water injection, cooling flow modulation, throttle push and an auxiliary power plant were evaluated using military life cycle cost (LCC) and commercial helicopter direct operating cost (DOC) merit factors in a rubber engine/rubber aircraft scenario.

Serotonin-induced hypophagia is mediated via α2 and β2 adrenergic receptors in neonatal layer-type chickens.

PubMed

Zendehdel, M; Sardari, F; Hassanpour, S; Rahnema, M; Adeli, A; Ghashghayi, E

2017-06-01

1. Serotoninergic and adrenergic systems play crucial roles in feed intake regulation in avians but there is no report on possible interactions among them. So, in this study, 5 experiments were designed to evaluate the interaction of central serotonergic and adrenergic systems on food intake regulation in 3 h food deprived (FD 3 ) neonatal layer-type chickens. 2. In Experiment 1, chickens received intracerebroventricular (ICV) injection of control solution, serotonin (56.74 nmol), prazosin (α 1 receptor antagonist, 10 nmol) and co-injection of serotonin plus prazosin. In Experiment 2, control solution, serotonin (56.74 nmol), yohimbine (α 2 receptor antagonist, 13 nmol) and co-injection of serotonin plus yohimbine were used. In Experiment 3, the birds received control solution, serotonin (56.74 nmol), metoprolol (β 1 receptor antagonist, 24 nmol) and co-injection of serotonin plus metoprolol. In Experiment 4, injections were control solution, serotonin (56.74 nmol), ICI 118.551 (β 2 receptor antagonist, 5 nmol) and serotonin plus ICI 118.551. In Experiment 5, control solution, serotonin (56.74 nmol), SR59230R (β 3 receptor antagonist, 20 nmol) and co-administration of serotonin and SR59230R were injected. In all experiments the cumulative food intake was measured until 120 min post injection. 3. The results showed that ICV injection of serotonin alone decreased food intake in chickens. A combined injection of serotonin plus ICI 118.551 significantly attenuated serotonin-induced hypophagia. Also, co-administration of serotonin and yohimbine significantly amplified the hypophagic effect of serotonin. However, prazosin, metoprolol and SR59230R had no effect on serotonin-induced hypophagia in chickens. 4. These results suggest that serotonin-induced feeding behaviour is probably mediated via α 2 and β 2 adrenergic receptors in neonatal layer-type chicken.

Efficacy trial of Camouflage Syringe to reduce dental fear and anxiety.

PubMed

Ujaoney, S; Mamtani, M; Thakre, T; Tote, J; Hazarey, V; Hazarey, P; Kulkarni, H

2013-12-01

Dental fear and anxiety in early childhood are widely prevalent and contribute to dental problems and behaviour in adulthood. Novel ways to reduce dental fear and anxiety in children are needed. Our aim was to conduct an efficacy trial of a novel Camouflage Syringe to reduce dental fear and anxiety in children. randomised controlled trial of efficacy of the Camouflage Syringe. We designed a Camouflage Syringe with a toy-like appearance that veils the conventional syringe to permit topical application and injection of local anaesthesia and ensure more involvement of the patient in the treatment process. We conducted a concurrent parallel, randomised controlled trial (NCT01398007) on the efficacy of this Camouflage Syringe to reduce the dental fear and anxiety in children seeking dental treatment who required the use of local anaesthesia. Using Venham's clinical rating scale, Venham's picture test, parental stress questionnaire and recall questionnaire, the efficacy of the Camouflage Syringe to reduce dental fear and anxiety ranged from 82% to 97% for various outcomes and from 60% to 100% for prevention of related adverse outcomes. For all outcomes, the number needed to treat was close to unity. Our results strongly favour the use of Camouflage Syringe to reduce dental fear and anxiety in children.

Correlation of ultrasound-guided corticosteroid injection of the quadratus femoris with MRI findings of ischiofemoral impingement.

PubMed

Backer, Matthew W; Lee, Kenneth S; Blankenbaker, Donna G; Kijowski, Richard; Keene, James S

2014-09-01

MRI findings of ischiofemoral impingement (IFI) have been described, but there is little evidence for treatment with ultrasound-guided corticosteroid injection. The purpose of this study was to evaluate the effectiveness of ultrasound-guided corticosteroid injection of the quadratus femoris muscle as a treatment of IFI syndrome and to correlate the MRI findings with injection outcome. The medical records of 61 consecutively registered subjects who underwent bony pelvis MRI in which either IFI or quadratus femoris edema was described in the radiology report were retrospectively reviewed. Subjects with MRI findings of IFI and clinical confirmation of pain that could be attributed to IFI were included and divided into injection and control groups based on clinical management. Control subjects had MRI findings and clinical symptoms suggestive of IFI but underwent conservative therapy rather than injection. The control patients had adequate follow-up and clinical documentation to determine their response to treatment. Quadratus femoris muscle edema, fat atrophy, and hamstring tendinopathy were graded from none to severe (grades 0-3). The ischiofemoral and quadratus femoris spaces were also measured. Clinical presentation was classified as typical, somewhat typical, or not typical of IFI. Injection effectiveness was determined by reported pain reduction assessed before, immediately after, and 2 weeks after the procedure with a standard 10-cm visual analog scale. Response to treatment was classified as good (reduction in pain level > 2), mild or partial (reduced by 1 or 2), or no improvement. For patients who did not return their 2-week postinjection pain surveys, injection effectiveness was determined by qualitative assessments found in their clinical notes. A Kruskal-Wallis rank sum test was used to compare effectiveness of injection between groups (p < 0.05). The Fisher exact test was used to evaluate for associations between each MRI finding and injection outcome. Of the 61 patients, 20 patients had both MRI findings and clinical confirmation of pain related to IFI. These 20 patients were included in the study. Fifteen ultrasound-guided injections were performed in seven patients, and these seven patients were included in the injection group (mean age, 47 years; range, 15-66 years); 13 patients were included in the control group (mean age, 42 years; range, 16-62 years). All seven patients in the injection group and 12 of the 13 patients in the control group were women. In the injection group, the mean width of the ischiofemoral space was 12 mm (range, 7-22 mm), and the mean width of the quadratus femoris space was 9 mm (range, 5-16 mm). The mean edema grade was 1.4 (range, 0-3); mean atrophy grade, 1.4 (range, 0-3); and mean hamstring tendinopathy grade, 1 (range, 0-2). In the control group, the mean width of the ischiofemoral space was 9 mm (range, 6-17 mm); mean quadratus femoris space width, 7 mm (range, 3-15 mm); mean edema grade, 1.9 (range, 1-3); mean atrophy grade, 1.2 (range, 0-3); and mean hamstring tendinopathy grade, 1.2 (range, 0-3). No statistical difference was seen between the two groups before treatment. Pain reduction after injection over the 2-week period was statistically significant with a mean reduction of 1.7 (range, 1-2) for the injection group and 0.8 (range, 0-2) for the control group (p < 0.01). Eleven of 15 (73%) of the injections provided good relief, and four of 15 (27%) provided mild relief. None of the 15 injections provided no relief. In the control group, four of 14 (29%) subjects had good relief, three of 14 (21%) had mild relief, and seven of 14 (50%) had no relief (p < 0.01). Ultrasound-guided corticosteroid injection of the quadratus femoris muscle shows promise as an effective treatment of IFI syndrome. However, larger longitudinal studies are needed to help establish the role of ultrasound-guided injection in the workup and care of patients presenting with both MRI findings and clinical findings of IFI.

Intravitreal Aflibercept Injection in Eyes With Substantial Vision Loss After Laser Photocoagulation for Diabetic Macular Edema: Subanalysis of the VISTA and VIVID Randomized Clinical Trials.

PubMed

Wykoff, Charles C; Marcus, Dennis M; Midena, Edoardo; Korobelnik, Jean-François; Saroj, Namrata; Gibson, Andrea; Vitti, Robert; Berliner, Alyson J; Williams Liu, Zinaria; Zeitz, Oliver; Metzig, Carola; Schmelter, Thomas; Heier, Jeffrey S

2016-12-22

Information on the effect of anti-vascular endothelial growth factor therapy in eyes with diabetic macular edema (DME) with vision loss after macular laser photocoagulation is clinically valuable. To evaluate visual and anatomic outcomes in a subgroup of macular laser photocoagulation treatment control (hereafter laser control) eyes with substantial vision loss receiving treatment with intravitreal aflibercept injection. This investigation was a post hoc analysis of a subgroup of laser control eyes in 2 phase 3 trials-VISTA (Study of Intravitreal Aflibercept Injection in Patients With Diabetic Macular Edema) and VIVID (Intravitreal Aflibercept Injection in Vision Impairment Due to DME)-in a multicenter setting. One hundred nine laser control eyes with center-involving DME were included. Treatment with intravitreal aflibercept injection (2 mg) every 8 weeks after 5 monthly doses with sham injections on nontreatment visits starting at week 24 was initiated on meeting prespecified criteria of at least a 10-letter visual acuity loss at 2 consecutive visits or at least a 15-letter visual acuity loss from the best previous measurement at 1 visit and vision not better than at baseline. Visual and anatomic outcomes in a subgroup of laser control eyes receiving treatment with intravitreal aflibercept injection. Through week 100, a total of 63 of 154 eyes (40.9%) in VISTA and 46 of 133 eyes (34.6%) in VIVID initially randomized to laser control received treatment with intravitreal aflibercept injection. The median time from week 24 to the first intravitreal aflibercept injection treatment was 34.0 (VISTA) and 83.5 (VIVID) days. In this subgroup, the mean (SD) visual gain from baseline to week 100 was 2.2 (12.5) (VISTA) and 3.8 (10.1) (VIVID) letters. At the time of intravitreal aflibercept injection initiation, these eyes had a mean (SD) loss of 11.0 (10.1) (VISTA) and 10.0 (6.5) (VIVID) letters from baseline, and they subsequently gained a mean (SD) of 17.4 (9.7) (VISTA) and 13.6 (8.6) (VIVID) letters from the initiation of treatment with intravitreal aflibercept injection through week 100. There was a minimal mean change in central subfield thickness from baseline in these eyes at the time of intravitreal aflibercept injection initiation (an increase of 3.9 μm in VISTA and a decrease of 3.0 μm in VIVID), after which further mean (SD) reductions of 285.6 (202.6) μm (VISTA) and 313.4 (181.9) μm (VIVID) occurred through week 100. Intravitreal aflibercept injection improves visual and anatomic outcomes in eyes experiencing substantial vision loss after macular laser photocoagulation treatment for DME. clinicaltrials.gov Identifiers: NCT01363440 and NCT01331681.

Three Dimensional Solution of Pneumatic Active Control of Forebody Vortex Asymmetry

NASA Technical Reports Server (NTRS)

Kandil, Osama A.; SharafEl-Din, Hazem H.; Liu, C. H.

1995-01-01

Pneumatic active control of asymmetric vortical flows around a slender pointed forebody is investigated using the three dimensional solution for the compressible thin-layer Navier-Stokes equation. The computational applications cover the normal and tangential injection control of asymmetric flows around a 5 degree semi-apex angle cone at a 40 degree angle of attack, 1.4 freestream Mach number and 6 x 10(exp 6) freestream Reynolds number (based on the cone length). The effective tangential angle range of 67.5 approaches minus 67.5 degrees is used for both normal and tangential ports of injection. The effective axial length of injection is varied from 0.03 to 0.05. The computational solver uses the implicit, upwind, flux difference splitting finite volume scheme, and the grid consists of 161 x 55 x 65 points in the wrap around, normal and axial directions, respectively. The results show that tangential injection is more effective than normal injection.

Smart Sectors Program: Best Practices in Permitting Profile

EPA Pesticide Factsheets

Smart Sectors profile about a streamlined permitting success story between South Carolina Department of Health and Environmental Control, US Army Corps of Engineers, EPA, non-governmental organizations, and a major aircraft manufacturer in Charleston, SC.

Characterization of Reactivity Controlled Compression Ignition (RCCI) Using Premixed Gasoline and Direct-Injected Gasoline with a Cetane Improver on a Multi-Cylinder Engine

DOE PAGES

Dempsey, Adam B.; Curran, Scott; Reitz, Rolf D.

2015-04-14

The focus of the present paper was to characterize Reactivity Controlled Compression Ignition (RCCI) using a single-fuel approach of gasoline and gasoline mixed with a commercially available cetane improver on a multi-cylinder engine. RCCI was achieved by port-injecting a certification grade 96 research octane gasoline and direct-injecting the same gasoline mixed with various levels of a cetane improver, 2-ethylhexyl nitrate (EHN). The EHN volume percentages investigated in the direct-injected fuel were 10, 5, and 2.5%. The combustion phasing controllability and emissions of the different fueling combinations were characterized at 2300 rpm and 4.2 bar brake mean effective pressure over amore » variety of parametric investigations including direct injection timing, premixed gasoline percentage, and intake temperature. Comparisons were made to gasoline/diesel RCCI operation on the same engine platform at nominally the same operating condition. The experiments were conducted on a modern four cylinder light-duty diesel engine that was modified with a port-fuel injection system while maintaining the stock direct injection fuel system. The pistons were modified for highly premixed operation and feature an open shallow bowl design. The results indicate that the authority to control the combustion phasing through the fuel delivery strategy (e.g., direct injection timing or premixed gasoline percentage) is not a strong function of the EHN concentration in the direct-injected fuel. It was also observed that NOx emissions are a strong function of the global EHN concentration in-cylinder and the combustion phasing. Finally, in general, NOx emissions are significantly elevated for gasoline/gasoline+EHN operation compared with gasoline/diesel RCCI operation at a given operating condition.« less

Autologous whole blood versus corticosteroid local injection in treatment of plantar fasciitis: A randomized, controlled multicenter clinical trial.

PubMed

Karimzadeh, Afshin; Raeissadat, Seyed Ahmad; Erfani Fam, Saleh; Sedighipour, Leyla; Babaei-Ghazani, Arash

2017-03-01

Plantar fasciitis is the most common cause of heel pain. Local injection modalities are among treatment options in patients with resistant pain. The aim of the present study was to evaluate the effect of local autologous whole blood compared with corticosteroid local injection in treatment of plantar fasciitis. In this randomized controlled multicenter study, 36 patients with chronic plantar fasciitis were recruited. Patients were allocated randomly into three treatment groups: local autologous blood, local corticosteroid injection, and control groups receiving no injection. Patients were assessed with visual analog scale (VAS), pressure pain threshold (PPT), and plantar fasciitis pain/disability scale (PFPS) before treatment, as well as 4 and 12 weeks post therapy. Variables of pain and function improved significantly in both corticosteroid and autologous blood groups compared to control group. At 4 weeks following treatment, patients in corticosteroid group had significantly lower levels of pain than patients in autologous blood and control groups (higher PPT level, lower PFPS, and VAS). After 12 weeks of treatment, both corticosteroid and autologous blood groups had lower average levels of pain than control group. The corticosteroid group showed an early sharp and then more gradual improvement in pain scores, but autologous blood group had a steady gradual drop in pain. Autologous whole blood and corticosteroid local injection can both be considered as effective methods in the treatment of chronic plantar fasciitis. These treatments decrease pain and significantly improve function compared to no treatment.

Parathyroid Hormone Injection

MedlinePlus

... injection is used along with calcium and vitamin D to treat low levels of calcium in the ... condition can be controlled by calcium and vitamin D alone. Parathyroid hormone injection is in a class ...

Electrochemical attosyringe.

PubMed

Laforge, François O; Carpino, James; Rotenberg, Susan A; Mirkin, Michael V

2007-07-17

The ability to manipulate ultrasmall volumes of liquids is essential in such diverse fields as cell biology, microfluidics, capillary chromatography, and nanolithography. In cell biology, it is often necessary to inject material of high molecular weight (e.g., DNA, proteins) into living cells because their membranes are impermeable to such molecules. All techniques currently used for microinjection are plagued by two common problems: the relatively large injector size and volume of injected fluid, and poor control of the amount of injected material. Here we demonstrate the possibility of electrochemical control of the fluid motion that allows one to sample and dispense attoliter-to-picoliter (10(-18) to 10(-12) liter) volumes of either aqueous or nonaqueous solutions. By changing the voltage applied across the liquid/liquid interface, one can produce a sufficient force to draw solution inside a nanopipette and then inject it into an immobilized biological cell. A high success rate was achieved in injections of fluorescent dyes into cultured human breast cells. The injection of femtoliter-range volumes can be monitored by video microscopy, and current/resistance-based approaches can be used to control injections from very small pipettes. Other potential applications of the electrochemical syringe include fluid dispensing in nanolithography and pumping in microfluidic systems.