Disposable Electronic Cigarettes and Electronic Hookahs: Evaluation of Performance

PubMed Central

Williams, Monique; Ghai, Sanjay

2015-01-01

Introduction: The purpose of this study was to characterize the performance of disposable button-activated and disposable airflow-activated electronic cigarettes (EC) and electronic hookahs (EH). Methods: The airflow rate required to produce aerosol, pressure drop, and the aerosol absorbance at 420nm were measured during smoke-outs of 9 disposable products. Three units of each product were tested in these experiments. Results: The airflow rates required to produce aerosol and the aerosol absorbances were lower for button-activated models (3mL/s; 0.41–0.55 absorbance) than for airflow-activated models (7–17mL/s; 0.48–0.84 absorbance). Pressure drop was also lower across button-activated products (range = 6–12mm H2O) than airflow-activated products (range = 15–67mm H20). For 25 of 27 units tested, airflow did not have to be increased during smoke-out to maintain aerosol production, unlike earlier generation models. Two brands had uniform performance characteristics for all parameters, while 3 had at least 1 product that did not function normally. While button-activated models lasted 200 puffs or less and EH airflow-activated models often lasted 400 puffs, none of the models produced as many puffs as advertised. Puff number was limited by battery life, which was shorter in button-activated models. Conclusion: The performance of disposable products was differentiated mainly by the way the aerosol was produced (button vs airflow-activated) rather than by product type (EC vs EH). Users needed to take harder drags on airflow-activated models. Performance varied within models, and battery life limited the number of puffs. Data suggest quality control in manufacturing varies among brands. PMID:25104117

Dispersion Modeling Using Ensemble Forecasts Compared to ETEX Measurements.

NASA Astrophysics Data System (ADS)

Straume, Anne Grete; N'dri Koffi, Ernest; Nodop, Katrin

1998-11-01

Numerous numerical models are developed to predict long-range transport of hazardous air pollution in connection with accidental releases. When evaluating and improving such a model, it is important to detect uncertainties connected to the meteorological input data. A Lagrangian dispersion model, the Severe Nuclear Accident Program, is used here to investigate the effect of errors in the meteorological input data due to analysis error. An ensemble forecast, produced at the European Centre for Medium-Range Weather Forecasts, is then used as model input. The ensemble forecast members are generated by perturbing the initial meteorological fields of the weather forecast. The perturbations are calculated from singular vectors meant to represent possible forecast developments generated by instabilities in the atmospheric flow during the early part of the forecast. The instabilities are generated by errors in the analyzed fields. Puff predictions from the dispersion model, using ensemble forecast input, are compared, and a large spread in the predicted puff evolutions is found. This shows that the quality of the meteorological input data is important for the success of the dispersion model. In order to evaluate the dispersion model, the calculations are compared with measurements from the European Tracer Experiment. The model manages to predict the measured puff evolution concerning shape and time of arrival to a fairly high extent, up to 60 h after the start of the release. The modeled puff is still too narrow in the advection direction.

MESOI Version 2. 0: an interactive mesoscale Lagrangian puff dispersion model with deposition and decay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramsdell, J.V.; Athey, G.F.; Glantz, C.S.

1983-11-01

MESOI Version 2.0 is an interactive Lagrangian puff model for estimating the transport, diffusion, deposition and decay of effluents released to the atmosphere. The model is capable of treating simultaneous releases from as many as four release points, which may be elevated or at ground-level. The puffs are advected by a horizontal wind field that is defined in three dimensions. The wind field may be adjusted for expected topographic effects. The concentration distribution within the puffs is initially assumed to be Gaussian in the horizontal and vertical. However, the vertical concentration distribution is modified by assuming reflection at the groundmore » and the top of the atmospheric mixing layer. Material is deposited on the surface using a source depletion, dry deposition model and a washout coefficient model. The model also treats the decay of a primary effluent species and the ingrowth and decay of a single daughter species using a first order decay process. This report is divided into two parts. The first part discusses the theoretical and mathematical bases upon which MESOI Version 2.0 is based. The second part contains the MESOI computer code. The programs were written in the ANSI standard FORTRAN 77 and were developed on a VAX 11/780 computer. 43 references, 14 figures, 13 tables.« less

Injector design for liner-on-target gas-puff experiments

NASA Astrophysics Data System (ADS)

Valenzuela, J. C.; Krasheninnikov, I.; Conti, F.; Wessel, F.; Fadeev, V.; Narkis, J.; Ross, M. P.; Rahman, H. U.; Ruskov, E.; Beg, F. N.

2017-11-01

We present the design of a gas-puff injector for liner-on-target experiments. The injector is composed of an annular high atomic number (e.g., Ar and Kr) gas and an on-axis plasma gun that delivers an ionized deuterium target. The annular supersonic nozzle injector has been studied using Computational Fluid Dynamics (CFD) simulations to produce a highly collimated (M > 5), ˜1 cm radius gas profile that satisfies the theoretical requirement for best performance on ˜1-MA current generators. The CFD simulations allowed us to study output density profiles as a function of the nozzle shape, gas pressure, and gas composition. We have performed line-integrated density measurements using a continuous wave (CW) He-Ne laser to characterize the liner gas density. The measurements agree well with the CFD values. We have used a simple snowplow model to study the plasma sheath acceleration in a coaxial plasma gun to help us properly design the target injector.

Injector design for liner-on-target gas-puff experiments.

PubMed

Valenzuela, J C; Krasheninnikov, I; Conti, F; Wessel, F; Fadeev, V; Narkis, J; Ross, M P; Rahman, H U; Ruskov, E; Beg, F N

2017-11-01

We present the design of a gas-puff injector for liner-on-target experiments. The injector is composed of an annular high atomic number (e.g., Ar and Kr) gas and an on-axis plasma gun that delivers an ionized deuterium target. The annular supersonic nozzle injector has been studied using Computational Fluid Dynamics (CFD) simulations to produce a highly collimated (M > 5), ∼1 cm radius gas profile that satisfies the theoretical requirement for best performance on ∼1-MA current generators. The CFD simulations allowed us to study output density profiles as a function of the nozzle shape, gas pressure, and gas composition. We have performed line-integrated density measurements using a continuous wave (CW) He-Ne laser to characterize the liner gas density. The measurements agree well with the CFD values. We have used a simple snowplow model to study the plasma sheath acceleration in a coaxial plasma gun to help us properly design the target injector.

An Analysis of a Puff Dispersion Model for a Coastal Region.

DTIC Science & Technology

1982-06-01

gril is determined by computing their movement for a finite time step using a measured wind field. The growth and buoyancy of the puffs are computed...advection step. The grid concentrations can be allowed to accumulate or simply be updated with the lat- est instantaneous value. & minimum gril concentration

Effect of smoking parameters on the particle size distribution and predicted airway deposition of mainstream cigarette smoke.

PubMed

Kane, David B; Asgharian, Bahman; Price, Owen T; Rostami, Ali; Oldham, Michael J

2010-02-01

It is known that puffing conditions such as puff volume, duration, and frequency vary substantially among individual smokers. This study investigates how these parameters affect the particle size distribution and concentration of fresh mainstream cigarette smoke (MCS) and how these changes affect the predicted deposition of MCS particles in a model human respiratory tract. Measurements of the particle size distribution made with an electrical low pressure impactor for a variety of puffing conditions are presented. The average flow rate of the puff is found to be the major factor effecting the measured particle size distribution of the MCS. The results of these measurements were then used as input to a deterministic dosimetry model (MPPD) to estimate the changes in the respiratory tract deposition fraction of smoke particles. The MPPD dosimetry model was modified by incorporating mechanisms involved in respiratory tract deposition of MCS: hygroscopic growth, coagulation, evaporation of semivolatiles, and mixing of the smoke with inhaled dilution air. The addition of these mechanisms to MPPD resulted in reasonable agreement between predicted airway deposition and human smoke retention measurements. The modified MPPD model predicts a modest 10% drop in the total deposition efficiency in a model human respiratory tract as the puff flow rate is increased from 1050 to 3100 ml/min, for a 2-s puff.

Puffing Topography and Nicotine Intake of Electronic Cigarette Users

PubMed Central

Behar, Rachel Z.; Hua, My; Talbot, Prue

2015-01-01

Background Prior electronic cigarette (EC) topography data are based on two video analyses with limited parameters. Alternate methods for measuring topography are needed to understand EC use and nicotine intake. Objectives This study evaluated EC topography with a CReSS Pocket device and quantified nicotine intake. Methods Validation tests on pressure drop, flow rate, and volume confirmed reliable performance of the CReSS Pocket device. Twenty participants used Blu Cigs and V2 Cigs for 10 minute intervals with a 10–15 minute break between brands. Brand order was reversed and repeated within 7 days Data were analyzed to determine puff duration, puff count, volume, flow rate, peak flow, and inter-puff interval. Nicotine intake was estimated from cartomizer fluid consumption and topography data. Results Nine patterns of EC use were identified. The average puff count and inter-puff interval were 32 puffs and 17.9 seconds. All participants, except one, took more than 20 puffs/10 minutes. The averages for puff duration (2.65 seconds/puff), volume/puff (51ml/puff), total puff volume (1,579 ml), EC fluid consumption (79.6 mg), flow rate (20 ml/s), and peak flow rate (27 ml/s) were determined for 10-minute sessions. All parameters except total puff count were significantly different for Blu versus V2 EC. Total volume for Blu versus V2 was four-times higher than for conventional cigarettes. Average nicotine intake for Blu and V2 across both sessions was 1.2 ± 0.5 mg and 1.4 ± 0.7 mg, respectively, which is similar to conventional smokers. Conclusions EC puffing topography was variable among participants in the study, but often similar within an individual between brands or days. Puff duration, inter-puff interval, and puff volume varied from conventional cigarette standards. Data on total puff volume and nicotine intake are consistent with compensatory usage of EC. These data can contribute to the development of a standard protocol for laboratory testing of EC products. PMID:25664463

Fluorescence Fluctuations and Equivalence Classes of Ca 2+ Imaging Experiments

PubMed Central

Piegari, Estefanía; Lopez, Lucía; Perez Ipiña, Emiliano; Ponce Dawson, Silvina

2014-01-01

release into the cytosol through inositol 1,4,5-trisphosphate receptors (IP3Rs) plays a relevant role in numerous physiological processes. IP3R-mediated signals involve -induced -release (CICR) whereby release through one open IP3R induces the opening of other channels. IP3Rs are apparently organized in clusters. The signals can remain localized (i.e., puffs) if CICR is limited to one cluster or become waves that propagate between clusters. puffs are the building blocks of waves. Thus, there is great interest in determining puff properties, especially in view of the current controversy on the spatial distribution of activatable IP3Rs. puffs have been observed in intact cells with optical techniques proving that they are intrinsically stochastic. Obtaining a correct picture of their dynamics then entails being able to detect the whole range of puff sizes. puffs are observed using visible single-wavelength dyes, slow exogenous buffers (e.g., EGTA) to disrupt inter-cluster CICR and UV-photolyzable caged IP3. Single-wavelength dyes increase their fluorescence upon calcium binding producing images that are strongly dependent on their kinetic, transport and photophysical properties. Determining the artifacts that the imaging setting introduces is particularly relevant when trying to analyze the smallest signals. In this paper we introduce a method to estimate the expected signal-to-noise ratio of imaging experiments that use single-wavelength dyes. The method is based on the Number and Brightness technique. It involves the performance of a series of experiments and their subsequent analysis in terms of a fluorescence fluctuation model with which the model parameters are quantified. Using the model, the expected signal-to-noise ratio is then computed. Equivalence classes between different experimental conditions that produce images with similar signal-to-noise ratios can then be established. The method may also be used to estimate the smallest signals that can reliably be observed with each setting. PMID:24776736

Panic Attack History and Smoking Topography

PubMed Central

Farris, Samantha G.; Brown, Lily A.; Goodwin, Renee D.; Zvolensky, Michael J.

2016-01-01

Background Little is known about panic attacks and puffing topography, a behavioral index of the value of smoking reinforcement. This study examined smoking style during the course of smoking of a single cigarette among adult daily smokers with and without a history of panic attacks. Method Participants (n = 124, Mage = 43.9, SD = 9.7; 44.4% female) were non-treatment seeking daily smokers. Lifetime panic attack history was assessed via diagnostic assessment; 28.2% (n = 35) of the sample had a panic attack history. Participants smoked one cigarette during an ad libitum smoking trial. Puff volume, duration, and inter-puff interval were measured using the Clinical Research Support System (CReSS) pocket device. Results Regression analyses revealed that panic attack status was not associated with significant differences in average puff volume, duration, or inter-puff interval. Multi-level modeling was used to examine puffing trajectories. Puff-level data revealed that there was a significant quadratic time x panic effect for puff volume and duration. Those with a panic attack history demonstrated relatively sustained levels of both puff volume and duration over time, whereas those without a history of panic attacks demonstrated an increase followed by a decrease in volume and duration over time. These effects were not accounted for by the presence of general psychopathology. Discussion Smokers with a panic attack history demonstrate more persistent efforts to self-regulate the delivery of nicotine, and thus may be at risk for continued smoking and dependence. Tailored treatment may be needed to address unique vulnerabilities among this group. PMID:28033542

Panic attack history and smoking topography.

PubMed

Farris, Samantha G; Brown, Lily A; Goodwin, Renee D; Zvolensky, Michael J

2017-02-01

Little is known about panic attacks and puffing topography, a behavioral index of the value of smoking reinforcement. This study examined smoking style during the course of smoking of a single cigarette among adult daily smokers with and without a history of panic attacks. Participants (n=124, M age =43.9, SD=9.7; 44.4% female) were non-treatment seeking daily smokers. Lifetime panic attack history was assessed via diagnostic assessment; 28.2% (n=35) of the sample had a panic attack history. Participants smoked one cigarette during an ad libitum smoking trial. Puff volume, duration, and inter-puff interval were measured using the Clinical Research Support System (CReSS) pocket device. Regression analyses revealed that panic attack status was not associated with significant differences in average puff volume, duration, or inter-puff interval. Multi-level modeling was used to examine puffing trajectories. Puff-level data revealed that there was a significant quadratic time x panic effect for puff volume and duration. Those with a panic attack history demonstrated relatively sustained levels of both puff volume and duration over time, whereas those without a history of panic attacks demonstrated an increase followed by a decrease in volume and duration over time. These effects were not accounted for by the presence of general psychopathology. Smokers with a panic attack history demonstrate more persistent efforts to self-regulate the delivery of nicotine, and thus may be at risk for continued smoking and dependence. Tailored treatment may be needed to address unique vulnerabilities among this group. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

A Link between Adolescent Nicotine Metabolism and Smoking Topography

PubMed Central

Moolchan, Eric T.; Parzynski, Craig S.; Jaszyna-Gasior, Maria; Collins, Charles C.; Leff, Michelle K.; Zimmerman, Debra L.

2009-01-01

Adult slow nicotine metabolizers have lower smoke exposure, carbon monoxide levels, and plasma nicotine levels than normal and fast metabolizers. Emerging evidence suggests nicotine metabolism influences smoking topography. This study investigated the association of nicotine metabolism (the ratio of plasma 3-hydroxycotinine to cotinine; 3OHCOT/COT) with smoking topography in adolescent smokers (N=85, 65% female, 68% European American, mean age 15.3 ± 1.2, mean cigarettes per day (CPD) 18.5 ± 8.5, mean Fagerström Test for Nicotine Dependence (FTND) 7.0 ± 1.2) presenting for a nicotine replacement therapy trial. Measures obtained included puff volume, inter-puff interval, number of puffs, puff duration, and puff velocity. Linear regression analysis controlling for hormonal contraception use showed that 3OHCOT/COT ratios predicted mean puff volume in the overall sample (t = 2.126, p = .037, adjusted R2 = .067). After gender stratification, faster metabolism predicted higher mean puff volume (t = 2.81, p = .009, adjusted R2 = .192) but fewer puffs (t = −3.160, p=0.004, adjusted R2 = .237) and lower mean puff duration (t = −2.06, p = .048, adjusted R2 = .101) among boys only, suggesting that as nicotine metabolism increases, puff volume increases but puffing frequency decreases. No significant relationships were found between nicotine metabolism and total puff volume, mean puff duration, inter-puff interval, or puff velocity. If confirmed in a broader sample of adolescent smokers, these findings suggest that, as among dependent adult smokers, rate of metabolism among adolescent boys is linked to select parameters of puffing behavior that may impact cessation ability. PMID:19423535

Buffer regulation of calcium puff sequences.

PubMed

Fraiman, Daniel; Dawson, Silvina Ponce

2014-02-01

Puffs are localized Ca(2 +) signals that arise in oocytes in response to inositol 1,4,5-trisphosphate (IP3). They are the result of the liberation of Ca(2 +) from the endoplasmic reticulum through the coordinated opening of IP3 receptor/channels clustered at a functional release site. The presence of buffers that trap Ca(2 +) provides a mechanism that enriches the spatio-temporal dynamics of cytosolic calcium. The expression of different types of buffers along the cell's life provides a tool with which Ca(2 +) signals and their responses can be modulated. In this paper we extend the stochastic model of a cluster of IP3R-Ca(2 +) channels introduced previously to elucidate the effect of buffers on sequences of puffs at the same release site. We obtain analytically the probability laws of the interpuff time and of the number of channels that participate of the puffs. Furthermore, we show that under typical experimental conditions the effect of buffers can be accounted for in terms of a simple inhibiting function. Hence, by exploring different inhibiting functions we are able to study the effect of a variety of buffers on the puff size and interpuff time distributions. We find the somewhat counter-intuitive result that the addition of a fast Ca(2 +) buffer can increase the average number of channels that participate of a puff.

Buffer regulation of calcium puff sequences

NASA Astrophysics Data System (ADS)

Fraiman, Daniel; Ponce Dawson, Silvina

2014-02-01

Puffs are localized Ca2 + signals that arise in oocytes in response to inositol 1,4,5-trisphosphate (IP3). They are the result of the liberation of Ca2 + from the endoplasmic reticulum through the coordinated opening of IP3 receptor/channels clustered at a functional release site. The presence of buffers that trap Ca2 + provides a mechanism that enriches the spatio-temporal dynamics of cytosolic calcium. The expression of different types of buffers along the cell's life provides a tool with which Ca2 + signals and their responses can be modulated. In this paper we extend the stochastic model of a cluster of IP3R-Ca2 + channels introduced previously to elucidate the effect of buffers on sequences of puffs at the same release site. We obtain analytically the probability laws of the interpuff time and of the number of channels that participate of the puffs. Furthermore, we show that under typical experimental conditions the effect of buffers can be accounted for in terms of a simple inhibiting function. Hence, by exploring different inhibiting functions we are able to study the effect of a variety of buffers on the puff size and interpuff time distributions. We find the somewhat counter-intuitive result that the addition of a fast Ca2 + buffer can increase the average number of channels that participate of a puff.

Dosage-based parameters for characterization of puff dispersion results.

PubMed

Berbekar, Eva; Harms, Frank; Leitl, Bernd

2015-01-01

A set of parameters is introduced to characterize the dispersion of puff releases based on the measured dosage. These parameters are the dosage, peak concentration, arrival time, peak time, leaving time, ascent time, descent time and duration. Dimensionless numbers for the scaling of the parameters are derived from dimensional analysis. The dimensionless numbers are tested and confirmed based on a statistically representative wind tunnel dataset. The measurements were carried out in a 1:300 scale model of the Central Business District in Oklahoma City. Additionally, the effect of the release duration on the puff parameters is investigated. Copyright © 2014 Elsevier B.V. All rights reserved.

Comparison of Ecological Momentary Assessment Versus Direct Measurement of E-Cigarette Use With a Bluetooth-Enabled E-Cigarette: A Pilot Study.

PubMed

Pearson, Jennifer L; Elmasry, Hoda; Das, Babita; Smiley, Sabrina L; Rubin, Leslie F; DeAtley, Teresa; Harvey, Emily; Zhou, Yitong; Niaura, Raymond; Abrams, David B

2017-05-29

Assessing the frequency and intensity of e-cigarette use presents special challenges beyond those posed by cigarette use. Accurate measurement of e-cigarette consumption, puff duration, and the stability of these measures over time will be informative for estimating the behavioral and health effects of e-cigarette use. The purpose of this pilot study was to compare the accuracy of self-reported e-cigarette puff counts collected via ecological momentary assessment (EMA) to objective puff count data collected by a Bluetooth-enabled e-cigarette device and to examine the feasibility and acceptability of using a second-generation e-cigarette among adult smokers. A total of 5 adult smokers were enrolled in a longitudinal parent study assessing how e-cigarette use affects cigarette use among e-cigarette-naïve smokers. Using a text message-based EMA system, participants reported e-cigarette puffs for 2 weeks. Participants were also given a Bluetooth-enabled e-cigarette (Smokio) that passively collected puff counts and puff duration. Comparisons between mean reports of Smokio (device-report) and EMA (self-report) use were evaluated using paired t tests. Correlation and agreement between device- and self-reports were evaluated using Pearson correlation and the concordance correlation coefficient (CCC), respectively. A linear mixed effect model was used to determine the fixed effect of timing and Smokio-reported daily puffs on report accuracy. We examined the relationship between time of day and reporting accuracy using Tukey's test for multiple pairwise comparisons. A total of 5 African American participants, 4 men and 1 woman, who ranged in age from 24 to 59 years completed the study, resulting in 5180 observations (device-report) of e-cigarette use. At baseline, participants reported smoking for 5 to 25 years and consumed a mean of 7 to 13 cigarettes per day (CPD); 4 smoked within 30 minutes of waking. At the 30-day follow-up, CPD range decreased to 1 to 3 cigarettes; 4 participants reported past 7-day e-cigarette use, and 1 participant reported no cigarette smoking in the past 7 days. Over 2 weeks of e-cigarette use, participants took an average of 1074 e-cigarette (SD 779.0) puffs per person as captured by the device reports. Each participant took a mean of 75.0 (SD 58.8) puffs per day, with each puff lasting an average of 3.6 (SD 2.4) seconds. Device reports captured an average of 33.3 (SD 47.8) more puffs per person per day than the self-reported e-cigarette puffs. In 87% of days, participants underestimated the number of puffs they had taken on the Smokio. There was significant moderate correlation (r=.47, P<.001) but poor agreement (p c =0.31, 95% CI 0.15-0.46) between the device- and self-reported data. Reporting accuracy was affected by amount and timing of e-cigarette use. Compared to self-reported e-cigarette use, the Bluetooth-enabled device captured significantly more e-cigarette use and allowed for examination of puff duration in addition to puff counts. A Bluetooth-enabled e-cigarette is a powerful and feasible tool for objective collection of e-cigarette use behavior in the real world. ©Jennifer L Pearson, Hoda Elmasry, Babita Das, Sabrina L Smiley, Leslie F Rubin, Teresa DeAtley, Emily Harvey, Yitong Zhou, Raymond Niaura, David B Abrams. Originally published in JMIR Research Protocols (http://www.researchprotocols.org), 29.05.2017.

Comparison of Ecological Momentary Assessment Versus Direct Measurement of E-Cigarette Use With a Bluetooth-Enabled E-Cigarette: A Pilot Study

PubMed Central

Elmasry, Hoda; Das, Babita; Smiley, Sabrina L; Rubin, Leslie F; DeAtley, Teresa; Harvey, Emily; Zhou, Yitong; Niaura, Raymond; Abrams, David B

2017-01-01

Background Assessing the frequency and intensity of e-cigarette use presents special challenges beyond those posed by cigarette use. Accurate measurement of e-cigarette consumption, puff duration, and the stability of these measures over time will be informative for estimating the behavioral and health effects of e-cigarette use. Objective The purpose of this pilot study was to compare the accuracy of self-reported e-cigarette puff counts collected via ecological momentary assessment (EMA) to objective puff count data collected by a Bluetooth-enabled e-cigarette device and to examine the feasibility and acceptability of using a second-generation e-cigarette among adult smokers. Methods A total of 5 adult smokers were enrolled in a longitudinal parent study assessing how e-cigarette use affects cigarette use among e-cigarette–naïve smokers. Using a text message–based EMA system, participants reported e-cigarette puffs for 2 weeks. Participants were also given a Bluetooth-enabled e-cigarette (Smokio) that passively collected puff counts and puff duration. Comparisons between mean reports of Smokio (device-report) and EMA (self-report) use were evaluated using paired t tests. Correlation and agreement between device- and self-reports were evaluated using Pearson correlation and the concordance correlation coefficient (CCC), respectively. A linear mixed effect model was used to determine the fixed effect of timing and Smokio-reported daily puffs on report accuracy. We examined the relationship between time of day and reporting accuracy using Tukey's test for multiple pairwise comparisons. Results A total of 5 African American participants, 4 men and 1 woman, who ranged in age from 24 to 59 years completed the study, resulting in 5180 observations (device-report) of e-cigarette use. At baseline, participants reported smoking for 5 to 25 years and consumed a mean of 7 to 13 cigarettes per day (CPD); 4 smoked within 30 minutes of waking. At the 30-day follow-up, CPD range decreased to 1 to 3 cigarettes; 4 participants reported past 7-day e-cigarette use, and 1 participant reported no cigarette smoking in the past 7 days. Over 2 weeks of e-cigarette use, participants took an average of 1074 e-cigarette (SD 779.0) puffs per person as captured by the device reports. Each participant took a mean of 75.0 (SD 58.8) puffs per day, with each puff lasting an average of 3.6 (SD 2.4) seconds. Device reports captured an average of 33.3 (SD 47.8) more puffs per person per day than the self-reported e-cigarette puffs. In 87% of days, participants underestimated the number of puffs they had taken on the Smokio. There was significant moderate correlation (r=.47, P<.001) but poor agreement (pc=0.31, 95% CI 0.15-0.46) between the device- and self-reported data. Reporting accuracy was affected by amount and timing of e-cigarette use. Conclusions Compared to self-reported e-cigarette use, the Bluetooth-enabled device captured significantly more e-cigarette use and allowed for examination of puff duration in addition to puff counts. A Bluetooth-enabled e-cigarette is a powerful and feasible tool for objective collection of e-cigarette use behavior in the real world. PMID:28554877

Variability among electronic cigarettes in the pressure drop, airflow rate, and aerosol production.

PubMed

Williams, Monique; Talbot, Prue

2011-12-01

This study investigated the performance of electronic cigarettes (e-cigarettes), compared different models within a brand, compared identical copies of the same model within a brand, and examined performance using different protocols. Airflow rate required to generate aerosol, pressure drop across e-cigarettes, and aerosol density were examined using three different protocols. First 10 puff protocol: The airflow rate required to produce aerosol and aerosol density varied among brands, while pressure drop varied among brands and between the same model within a brand. Total air hole area correlated with pressure drop for some brands. Smoke-out protocol: E-cigarettes within a brand generally performed similarly when puffed to exhaustion; however, there was considerable variation between brands in pressure drop, airflow rate required to produce aerosol, and the total number of puffs produced. With this protocol, aerosol density varied significantly between puffs and gradually declined. CONSECUTIVE TRIAL PROTOCOL: Two copies of one model were subjected to 11 puffs in three consecutive trials with breaks between trials. One copy performed similarly in each trial, while the second copy of the same model produced little aerosol during the third trial. The different performance properties of the two units were attributed to the atomizers. There was significant variability between and within brands in the airflow rate required to produce aerosol, pressure drop, length of time cartridges lasted, and production of aerosol. Variation in performance properties within brands suggests a need for better quality control during e-cigarette manufacture.

Field Measurement and Model Evaluation Program for Assessment of the Environmental Effects of Military Smokes: Evaluation of Atmospheric Dispersion Models for Fog-Oil Smoke Dispersion

DTIC Science & Technology

1989-02-01

EK 111. TRIAL 19, L 2. \\ (,’, i / ඘ I€ m m B-02 I SMOKE WEEK IV -TRIAL 3 -- LOS1 DOSAGE 0.06 COMESIC U ACT II.......... MAD PUFF 0m0 _LUDWIG (1977...PUFF, AND LUDWIG (1977) WITH FIELD DATA FROM SMOKE WEEK IV. TRIAL 3. LOS1 l (c) For short release times and the calculation of dosages, the randomization

Prediction of dosage-based parameters from the puff dispersion of airborne materials in urban environments using the CFD-RANS methodology

NASA Astrophysics Data System (ADS)

Efthimiou, G. C.; Andronopoulos, S.; Bartzis, J. G.

2018-02-01

One of the key issues of recent research on the dispersion inside complex urban environments is the ability to predict dosage-based parameters from the puff release of an airborne material from a point source in the atmospheric boundary layer inside the built-up area. The present work addresses the question of whether the computational fluid dynamics (CFD)-Reynolds-averaged Navier-Stokes (RANS) methodology can be used to predict ensemble-average dosage-based parameters that are related with the puff dispersion. RANS simulations with the ADREA-HF code were, therefore, performed, where a single puff was released in each case. The present method is validated against the data sets from two wind-tunnel experiments. In each experiment, more than 200 puffs were released from which ensemble-averaged dosage-based parameters were calculated and compared to the model's predictions. The performance of the model was evaluated using scatter plots and three validation metrics: fractional bias, normalized mean square error, and factor of two. The model presented a better performance for the temporal parameters (i.e., ensemble-average times of puff arrival, peak, leaving, duration, ascent, and descent) than for the ensemble-average dosage and peak concentration. The majority of the obtained values of validation metrics were inside established acceptance limits. Based on the obtained model performance indices, the CFD-RANS methodology as implemented in the code ADREA-HF is able to predict the ensemble-average temporal quantities related to transient emissions of airborne material in urban areas within the range of the model performance acceptance criteria established in the literature. The CFD-RANS methodology as implemented in the code ADREA-HF is also able to predict the ensemble-average dosage, but the dosage results should be treated with some caution; as in one case, the observed ensemble-average dosage was under-estimated slightly more than the acceptance criteria. Ensemble-average peak concentration was systematically underpredicted by the model to a degree higher than the allowable by the acceptance criteria, in 1 of the 2 wind-tunnel experiments. The model performance depended on the positions of the examined sensors in relation to the emission source and the buildings configuration. The work presented in this paper was carried out (partly) within the scope of COST Action ES1006 "Evaluation, improvement, and guidance for the use of local-scale emergency prediction and response tools for airborne hazards in built environments".

Compositional profiling and sensorial analysis of multi-wholegrain extruded puffs as affected by fructan inclusion.

PubMed

Handa, C; Goomer, S

2015-09-01

Rice grits, corn grits, pulse, wholegrain - finger millet and sorghum were utilized in the production of multigrain extruded puffs using a single screw extruder. The effect of inclusion of fructan - fructoligosaccharide in multi-wholegrain (MWG) extruded puffs was examined. MWG fructan enriched puffs puffs had 450 % higher dietary fiber content than the control puff (CP). These puffs can be categorized as 'Good Source' of fiber as it suffices 17.2 % DV of fiber. Puffs were rated 8.1 ± 0.6, 8.3 ± 0.7, 8.1 ± 0.6, 7.5 ± 0.5 and 8.2 ± 0.6 for color, flavor, texture, appearance and overall acceptability respectively. The scores for all the attributes were found to be not significantly different (p < 0.05) from CP. The MWG fructan puffs were rated higher on flavor than the CP having a score of 8.3 ± 0.7 as opposed to 8.2 ± 0.4 for CP. This indicates that the nutritional quality and acceptability of MWG extruded puffs could be improved by the inclusion of fructans.

Plasma puff initiation of high Coulomb transfer switches

NASA Technical Reports Server (NTRS)

Venable, D. D.; Choi, E. H.

1990-01-01

The plasma-puff triggering mechanism based on a hypocycloidal pinch geometry was investigated to determine the optimal operating conditions for the azimuthally uniform surface flashover which initiates plasma-puff under wide range of fill gas pressure of Ar, He and N2. The optimal fill gas pressure for the azimuthally uniform plasma-puff was about 120 mTorr and 450 Torr for He and N2, and between 120 mTorr and 5 Torr for Ar. The inverse pinch switch was triggered with the plasma-puff and the switching capability under various electrical parameters and working gas pressures of Ar, He and N2 was determined. It was also shown that the azimuthally uniform switching discharges were dependent on the type of fill gas and its fill pressure. A new concept of plasma-focus driven plasma-puff was also discussed in comparison with the hypocycloidal pinch plasma-puff triggering. The main discharge of inverse pinch switch with plasma-focus driven plasma-puff trigger is found to be more azimuthally uniform than that with hypocycloidal pinch plasma-puff trigger in a gas pressure region between 80 mTorr and 1 Torr.

A comparison between a combination of ipratropium bromide plus fenoterol in a single metered dose inhaler (Duovent) and salbutamol in asthma.

PubMed Central

Flint, K. C.; Hockley, B.; Johnson, N. M.

1983-01-01

The efficacy of a single metered dose inhaler containing a combination of fenoterol (100 micrograms/puff) and ipratropium bromide (40 micrograms/puff) has been assessed in 12 asthmatics. We conclude that the bronchodilator effect of 2 puffs of the combination inhaler was significantly greater than that achieved by 2 puffs of salbutamol (100 micrograms/puff). PMID:6227877

Effects of design parameters and puff topography on heating coil temperature and mainstream aerosols in electronic cigarettes

NASA Astrophysics Data System (ADS)

Zhao, Tongke; Shu, Shi; Guo, Qiuju; Zhu, Yifang

2016-06-01

Emissions from electronic cigarettes (ECs) may contribute to both indoor and outdoor air pollution and the number of users is increasing rapidly. ECs operate based on the evaporation of e-liquid by a high-temperature heating coil. Both puff topography and design parameters can affect this evaporation process. In this study, both mainstream aerosols and heating coil temperature were measured concurrently to study the effects of design parameters and puff topography. The heating coil temperatures and mainstream aerosols varied over a wide range across different brands and within same brand. The peak heating coil temperature and the count median diameter (CMD) of EC aerosols increased with a longer puff duration and a lower puff flow rate. The particle number concentration was positively associated with the puff duration and puff flow rate. These results provide a better understanding of how EC emissions are affected by design parameters and puff topography and emphasize the urgent need to better regulate EC products.

The Experimental Study of Characterized Noble Gas Puffs Irradiated by Ultra-Short Laser Pulses Compared with X-Pinches as an X-Ray Source

NASA Astrophysics Data System (ADS)

Schultz, Kimberly Ann

The goal of this dissertation is to study the basic physics and X-ray emission (1-10 keV) of two X-ray sources: X-pinch plasmas and a clustered gas-puff irradiated by an ultrashort laser pulse. X-pinches and other typical X-ray sources using solid targets create hot debris that can damage sensitive equipment. Therefore, to perform sensitive backlighting or X-ray effects testing, debris-free sources of radiation must be investigated. In this work, the author presents a broad study of clustered noble gas puffs including characterization measurements and laser heating experiments using several gas nozzles and multiple gases. Ultimately, the goal is to compare the laser-irradiated gas-puff and X-pinch plasmas as X-ray sources. Characterization of the gas puffs is performed at the Radiation Physics Laboratory at the University of Nevada, Reno (UNR) Physics Department using optical interferometry and Rayleigh scattering to determine density and cluster radius. By changing the gas-puff variables control of both the density and cluster size of the gas jets is obtained. Two laser systems provide the high intensities desired for the laser-irradiated gas puff experiments: the UNR Leopard Laser (1-2x1019 W/cm2) and the Lawrence Livermore National Laboratory's Titan Laser (7x1019 W/cm2). X-ray emission is studied as a function of laser pulse parameters, gas target type, gas puff density, and the gas-delay timing between puff initiation and laser interaction with the puff. The tested gases are Ar, Kr, Xe, and four mixtures of the noble gases. Time-resolved X-ray measurements are captured with Silicon diodes and photoconducting diamond detectors. Electron beam detectors include Faraday cups and a high-energy (> 1 MeV) electron spectrometer. Modeling of spectra from X-ray crystal spectrometers provides plasma density and temperature measurement and a molecular dynamics (MD) code describes cluster interactions with the laser pulse. The conversion of laser energy into X rays is also measured. Laser beam transmission through and absorption by the gas puff reveal the complexity of using laser-irradiated gas puffs as X-ray sources. A strong anisotropy of X-ray and electron emissions were observed at both laser facilities. X-pinch plasmas can provide intense hard X rays and strong electron beams originating from small sources with many applications. Recent research has been conducted into four-wire X-pinches at the UNR Zebra machine, a 1-MA pulsed power generator. Two different wire materials are considered in this study, Ag and Mo. We observe a relatively linear correlation between load mass and implosion time for Mo X-pinches; in fact, this relationship also extends to include Ag. Interestingly, X-ray burst features drastically change in shape when the load mass is varied. Advantages of laser-irradiated gas puffs include a lack of damaging debris, high repetition rate, and ease of control. Its disadvantages include its inefficiency at converting electrical energy to X-rays, which is mostly limited by laser efficiency, and relatively low total energy yield. X-pinches, on the other hand, produced kJ of energy in a broad spectral region. However, they create a large amount of debris, have a low repetition rate, and, at 1-MA, have hard-to-predict implosion times.

Electronic Cigarette Topography in the Natural Environment

PubMed Central

Morabito, P. N.; Roundtree, K. A.

2015-01-01

This paper presents the results of a clinical, observational, descriptive study to quantify the use patterns of electronic cigarette users in their natural environment. Previously published work regarding puff topography has been widely indirect in nature, and qualitative rather than quantitative, with the exception of three studies conducted in a laboratory environment for limited amounts of time. The current study quantifies the variation in puffing behaviors among users as well as the variation for a given user throughout the course of a day. Puff topography characteristics computed for each puffing session by each subject include the number of subject puffs per puffing session, the mean puff duration per session, the mean puff flow rate per session, the mean puff volume per session, and the cumulative puff volume per session. The same puff topography characteristics are computed across all puffing sessions by each single subject and across all subjects in the study cohort. Results indicate significant inter-subject variability with regard to puffing topography, suggesting that a range of representative puffing topography patterns should be used to drive machine-puffed electronic cigarette aerosol evaluation systems. PMID:26053075

Electronic Cigarette Topography in the Natural Environment.

PubMed

Robinson, R J; Hensel, E C; Morabito, P N; Roundtree, K A

2015-01-01

This paper presents the results of a clinical, observational, descriptive study to quantify the use patterns of electronic cigarette users in their natural environment. Previously published work regarding puff topography has been widely indirect in nature, and qualitative rather than quantitative, with the exception of three studies conducted in a laboratory environment for limited amounts of time. The current study quantifies the variation in puffing behaviors among users as well as the variation for a given user throughout the course of a day. Puff topography characteristics computed for each puffing session by each subject include the number of subject puffs per puffing session, the mean puff duration per session, the mean puff flow rate per session, the mean puff volume per session, and the cumulative puff volume per session. The same puff topography characteristics are computed across all puffing sessions by each single subject and across all subjects in the study cohort. Results indicate significant inter-subject variability with regard to puffing topography, suggesting that a range of representative puffing topography patterns should be used to drive machine-puffed electronic cigarette aerosol evaluation systems.

Corneal biomechanical properties from air-puff corneal deformation imaging

NASA Astrophysics Data System (ADS)

Marcos, Susana; Kling, Sabine; Bekesi, Nandor; Dorronsoro, Carlos

2014-02-01

The combination of air-puff systems with real-time corneal imaging (i.e. Optical Coherence Tomography (OCT), or Scheimpflug) is a promising approach to assess the dynamic biomechanical properties of the corneal tissue in vivo. In this study we present an experimental system which, together with finite element modeling, allows measurements of corneal biomechanical properties from corneal deformation imaging, both ex vivo and in vivo. A spectral OCT instrument combined with an air puff from a non-contact tonometer in a non-collinear configuration was used to image the corneal deformation over full corneal cross-sections, as well as to obtain high speed measurements of the temporal deformation of the corneal apex. Quantitative analysis allows direct extraction of several deformation parameters, such as apex indentation across time, maximal indentation depth, temporal symmetry and peak distance at maximal deformation. The potential of the technique is demonstrated and compared to air-puff imaging with Scheimpflug. Measurements ex vivo were performed on 14 freshly enucleated porcine eyes and five human donor eyes. Measurements in vivo were performed on nine human eyes. Corneal deformation was studied as a function of Intraocular Pressure (IOP, 15-45 mmHg), dehydration, changes in corneal rigidity (produced by UV corneal cross-linking, CXL), and different boundary conditions (sclera, ocular muscles). Geometrical deformation parameters were used as input for inverse finite element simulation to retrieve the corneal dynamic elastic and viscoelastic parameters. Temporal and spatial deformation profiles were very sensitive to the IOP. CXL produced a significant reduction of the cornea indentation (1.41x), and a change in the temporal symmetry of the corneal deformation profile (1.65x), indicating a change in the viscoelastic properties with treatment. Combining air-puff with dynamic imaging and finite element modeling allows characterizing the corneal biomechanics in-vivo.

Developmental ecdysteroid titers and DNA puffs in larvae of two sciarid species, Rhynchosciara americana and Rhynchosciara milleri (Diptera: Sciaridae).

PubMed

Soares, M A M; Hartfelder, K; Tesserolli de Souza, J M; Stocker, A J

2015-10-01

Ecdysteroid titers, developmental landmarks and the presence of prominent amplifying regions (DNA puffs) have been compared during late larval to pupal development in four groups of Rhynchosciara americana larvae and in R. americana and Rhynchosciara milleri. Three prominent DNA puffs (B2, C3 and C8) expand and regress sequentially on the rising phase of the 20-hydroxyecdysone (20E) titer in R. americana as a firm, cellular cocoon is being constructed. A sharp rise in 20E coincides with the regression of these puffs. The shape of the 20E curve is similar in R. milleri, a species that does not construct a massive cocoon, but the behavior of certain DNA puffs and their temporal relationship to the curve differs. Regions corresponding to B2 and C3 can be identified in R. milleri by banding pattern similarity with R. americana chromosomes and, in the case of B2, by hybridization to an R. americana probe. A B2 puff appears in R. milleri as the 20E titer rises but remains small in all gland regions. A puff similar to the R. americana C3 puff occurs in posterior gland cells of R. milleri (C3(Rm)) after the B2 puff, but this site did not hybridize to R. americana C3 probes. C3(Rm) incorporated (3)H-thymidine above background, but showed less post-puff DNA accumulation than C3 of R. americana. R. americana C8 probes hybridized to a more distal region of the R. milleri C chromosome that did not appear to amplify or form a large puff. These differences can be related to developmental differences, in particular differences in cocoon construction between the two species.

Effects of income on drug choice in humans.

PubMed Central

DeGrandpre, R J; Bickel, W K; Rizvi, S A; Hughes, J R

1993-01-01

The effects of income (money available to spend during the experimental session) on human choice were examined in a concurrent-schedule arrangement. Subjects were 7 nicotine-dependent smokers, and reinforcers were puffs on the subject's usual brand of cigarette ("own") and puffs on a less preferred brand of cigarette with equal nicotine content ("other"). Across sessions, income varied and the price of the two reinforcers was held constant, with the other puffs one fifth the price of the own puffs. As income increased, consumption of own puffs increased while consumption of the less expensive other puffs decreased. These effects of income on choice were highly consistent across subjects. For some subjects, however, income had little effect on total puff consumption. Finally, an additional condition examined whether price and income manipulations would have functionally equivalent effects on choice by repeating an income condition in which the price of the other brand was increased. Although the increased price of the other puffs decreased their consumption in 4 subjects, 2 subjects showed increased consumption of the other puffs at the higher price. The results, when defined in economic terms, indicate that the own puffs were a normal good (consumption and income are directly related), the other puffs were an inferior good (consumption and income are inversely related), and the direct relationship between consumption of the other puffs and their price is defined as a Giffengood effect. The latter result also suggests that for these 2 subjects, price and income manipulations had equivalent effects on choice. These results extend findings from previous studies that have examined the effects of income on choice responding to human subjects and drug reinforcers, and provide a framework for further experimental tests of the effects of income on human choice behavior. Methodological and theoretical implications for the study of choice and for behavioral pharmacology are discussed. PMID:8315366

Iron pentacarbonyl detection limits in the cigarette smoke matrix using FT-IR spectroscopy

NASA Astrophysics Data System (ADS)

Parrish, Milton E.; Plunkett, Susan E.; Harward, Charles N.

2005-11-01

Endogenous metals present in tobacco from agricultural practices have been purported to generate metal carbonyls in cigarette smoke. Transition metal catalysts, such as iron oxide, have been investigated for the reduction of carbon monoxide (CO) in cigarette smoke. These studies motivated the development of an analytical method to determine if iron pentacarbonyl [Fe(CO) 5] is present in mainstream smoke from cigarette models having cigarette paper made with iron oxide. An FT-IR puff-by-puff method was developed and the detection limit was determined using two primary reference spectra from different sources to estimate the amount of Fe(CO) 5 present in a high-pressure steel cylinder of CO. We do not detect Fe(CO) 5 in a single 35 mL puff from reference cigarettes or from those cigarette models having cigarette paper made with iron oxide, with a 30-ppbV limit of detection (LOD). Also, it was shown that a filter containing activated carbon would remove Fe(CO) 5.

Temperature Evolution of a 1 MA Triple-Nozzle Gas-Puff Z-Pinch

NASA Astrophysics Data System (ADS)

de Grouchy, Philip; Banasek, Jacob; Engelbrecht, Joey; Qi, Niansheng; Atoyan, Levon; Byvank, Tom; Cahill, Adam; Moore, Hannah; Potter, William; Ransohoff, Lauren; Hammer, David; Kusse, Bruce; Laboratory of Plasma Studies Team

2015-11-01

Mitigation of the Rayleigh-Taylor instability (RTI) plays a critical role in optimizing x-ray output at high-energy ~ 13 keV using the triple-nozzle Krypton gas-puff at Sandia National Laboratory. RTI mitigation by gas-puff density profiling using a triple-nozzle gas-puff valve has recently been recently demonstrated on the COBRA 1MA z-pinch at Cornell University. In support of this work we investigate the role of shell cooling in the growth of RTI during gas-puff implosions. Temperature measurements within the imploding plasma shell are recorded using a 527 nm, 10 GW Thomson scattering diagnostic for Neon, Argon and Krypton puffs. The mass-density profile is held constant at 22 microgram per centimeter for all three puffs and the temperature evolution of the imploding material is recorded. In the case of Argon puffs we find that the shell ion and electron effective temperatures remain in equilibrium at around 1keV for the majority of the implosion phase. In contrast scattered spectra from Krypton are dominated by of order 10 keV effective ion temperatures. Supported by the NNSA Stewardship Sciences Academic Programs.

Characteristics of plasma-puff trigger for a inverse-pinch plasma switch

NASA Technical Reports Server (NTRS)

Choi, Eun H.; Venable, Demetrius D.; Han, Kwang S.; Lee, Ja H.

1993-01-01

The plasma-puff triggering mechanism based on a hypocycloidal pinch geometry was investigated to determine the optimal operating conditions for the azimuthally uniform surface flashover which initiates plasma-puff under wide ranges of fill gas pressure of Ar, He and N2. The optimal fill-gas pressure range for the azimuthally uniform plasma-puff was about 120 mTorr less than or equal to P(sub op) less than or equal to 450 Torr for He and N2. For Argon 120 mTorr is less than or equal to P(sub op) is less than or equal to 5 Torr. The inverse-pinch switch was triggered with the plasma-puff and the switching capability under various electrical parameters and working gas pressures of Ar, He and N2 was determined. The azimuthally uniform switching discharges were dependent on the type of fill gas and its fill pressure. A new concept of plasma-focus driven plasma-puff will be discussed in comparison with the current hypocycloidal-pinch plasma-puff triggering.

Application of Human Augmentics: A Persuasive Asthma Inhaler.

PubMed

Grossman, Brent; Conner, Steve; Mosnaim, Giselle; Albers, Joshua; Leigh, Jason; Jones, Steve; Kenyon, Robert

2017-03-01

This article describes a tailored health intervention delivered on a mobile phone platform, integrating low-literacy design strategies and basic principles of behavior change, to promote increased adherence and asthma control among underserved minority adolescents. We based the intervention and design principles on theories of Human Augmentics and the Elaboration Likelihood Model. We tested the efficacy of using electronic monitoring devices that incorporate informative and persuasive elements to improve adherence to a prescribed daily medication regimen intended to reduce use of asthma rescue medications. We describe the theoretical framework, hardware and software systems, and results of user testing for design purposes and a clinical pilot study incorporating use of the device and software by the targeted population. The results of the clinical pilot study showed an 83% completion rate for the treatment as well as improved adherence. Of note, 8% and 58% of participants achieved clinically significant adherence targets at baseline and last week of the study, respectively. Rescue asthma medication use decreased from a median of 3 puffs per week at baseline to 0 puffs per week during the last week of the study. Copyright © 2017 Elsevier Inc. All rights reserved.

Statespace geometry of puff formation in pipe flow

NASA Astrophysics Data System (ADS)

Budanur, Nazmi Burak; Hof, Bjoern

2017-11-01

Localized patches of chaotically moving fluid known as puffs play a central role in the transition to turbulence in pipe flow. Puffs coexist with the laminar flow and their large-scale dynamics sets the critical Reynolds number: When the rate of puff splitting exceeds that of decaying, turbulence in a long pipe becomes sustained in a statistical sense. Since puffs appear despite the linear stability of the Hagen-Poiseuille flow, one expects them to emerge from the bifurcations of finite-amplitude solutions of Navier-Stokes equations. In numerical simulations of pipe flow, Avila et al., discovered a pair of streamwise localized relative periodic orbits, which are time-periodic solutions with spatial drifts. We combine symmetry reduction and Poincaré section methods to compute the unstable manifolds of these orbits, revealing statespace structures associated with different stages of puff formation.

Behavioral economic substitutability of e-cigarettes, tobacco cigarettes, and nicotine gum.

PubMed

Johnson, Matthew W; Johnson, Patrick S; Rass, Olga; Pacek, Lauren R

2017-07-01

The public health impact of e-cigarettes may depend on their substitutability for tobacco cigarettes. Dual users of e-cigarettes and tobacco cigarettes completed purchasing tasks in which they specified daily use levels under hypothetical conditions that varied the availability and price of e-cigarettes, tobacco cigarettes, and nicotine gum (for those with nicotine gum experience). When either e-cigarettes or tobacco cigarettes were the only available commodity, as price per puff increased, purchasing decreased, revealing similar reinforcement profiles. When available concurrently, as the price of tobacco puffs increased, purchasing of tobacco puffs decreased while purchasing of fixed-price e-cigarette puffs increased. Among those with nicotine gum experience, when the price of tobacco puffs was closest to the actual market value of tobacco puffs, e-cigarette availability decreased median tobacco puff purchases by 44% compared to when tobacco was available alone. In contrast, nicotine gum availability caused no decrease in tobacco puff purchases. E-cigarettes may serve as a behavioral economic substitute for tobacco cigarettes, and may be a superior substitute compared to nicotine gum in their ability to decrease tobacco use. Although important questions remain regarding the health impacts of e-cigarettes, these data are consistent with the possibility that e-cigarettes may serve as smoking cessation/reduction aids.

Short-term emergency response planning and risk assessment via an integrated modeling system for nuclear power plants in complex terrain

NASA Astrophysics Data System (ADS)

Chang, Ni-Bin; Weng, Yu-Chi

2013-03-01

Short-term predictions of potential impacts from accidental release of various radionuclides at nuclear power plants are acutely needed, especially after the Fukushima accident in Japan. An integrated modeling system that provides expert services to assess the consequences of accidental or intentional releases of radioactive materials to the atmosphere has received wide attention. These scenarios can be initiated either by accident due to human, software, or mechanical failures, or from intentional acts such as sabotage and radiological dispersal devices. Stringent action might be required just minutes after the occurrence of accidental or intentional release. To fulfill the basic functions of emergency preparedness and response systems, previous studies seldom consider the suitability of air pollutant dispersion models or the connectivity between source term, dispersion, and exposure assessment models in a holistic context for decision support. Therefore, the Gaussian plume and puff models, which are only suitable for illustrating neutral air pollutants in flat terrain conditional to limited meteorological situations, are frequently used to predict the impact from accidental release of industrial sources. In situations with complex terrain or special meteorological conditions, the proposing emergency response actions might be questionable and even intractable to decisionmakers responsible for maintaining public health and environmental quality. This study is a preliminary effort to integrate the source term, dispersion, and exposure assessment models into a Spatial Decision Support System (SDSS) to tackle the complex issues for short-term emergency response planning and risk assessment at nuclear power plants. Through a series model screening procedures, we found that the diagnostic (objective) wind field model with the aid of sufficient on-site meteorological monitoring data was the most applicable model to promptly address the trend of local wind field patterns. However, most of the hazardous materials being released into the environment from nuclear power plants are not neutral pollutants, so the particle and multi-segment puff models can be regarded as the most suitable models to incorporate into the output of the diagnostic wind field model in a modern emergency preparedness and response system. The proposed SDSS illustrates the state-of-the-art system design based on the situation of complex terrain in South Taiwan. This system design of SDSS with 3-dimensional animation capability using a tailored source term model in connection with ArcView® Geographical Information System map layers and remote sensing images is useful for meeting the design goal of nuclear power plants located in complex terrain.

Predicting and validating the motion of an ash cloud during the 2006 eruption of Mount Augustine volcano

USGS Publications Warehouse

Collins, Richard L.; Fochesatto, Javier; Sassen, Kenneth; Webley, Peter W.; Atkinson, David E.; Dean, Kenneson G.; Cahill, Catherine F.; Mizutani, Kohei

2007-01-01

On 11 January 2006, Mount Augustine volcano in southern Alaska began erupting after 20- year repose. The Anchorage Forecast Office of the National Weather Service (NWS) issued an advisory on 28 January for Kodiak City. On 31 January, Alaska Airlines cancelled all flights to and from Anchorage after multiple advisories from the NWS for Anchorage and the surrounding region. The Alaska Volcano Observatory (AVO) had reported the onset of the continuous eruption. AVO monitors the approximately 100 active volcanoes in the Northern Pacific. Ash clouds from these volcanoes can cause serious damage to an aircraft and pose a serious threat to the local communities, and to transcontinental air traffic throughout the Arctic and sub-Arctic region. Within AVO, a dispersion model has been developed to track the dispersion of volcanic ash clouds. The model, Puff, was used operational by AVO during the Augustine eruptive period. Here, we examine the dispersion of a volcanic ash (or aerosol) cloud from Mount Augustine across Alaska from 29 January through the 2 February 2006. We present the synoptic meteorology, the Puff predictions, and measurements from aerosol samplers, laser radar (or lidar) systems, and satellites. Aerosol samplers revealed the presence of volcanic aerosols at the surface at sites where Puff predicted the ash clouds movement. Remote sensing satellite data showed the development of the ash cloud in close proximity to the volcano consistent with the Puff predictions. Two lidars showed the presence of volcanic aerosol with consistent characteristics aloft over Alaska and were capable of detecting the aerosol, even in the presence of scattered clouds and where the ash cloud is too thin/disperse to be detected by remote sensing satellite data. The lidar measurements revealed the different trajectories of ash consistent with the Puff predictions. Dispersion models provide a forecast of volcanic ash cloud movement that might be undetectable by any other means but are still a significant hazard. Validation is the key to assessing the accuracy of any predictions. The study highlights the use of multiple and complementary observations used in detecting the trajectory ash cloud, both at the surface and aloft in the atmosphere.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Webley, Peter W.; Atkinson, D.; Collins, Richard L.

On 11 January 2006, Mount Augustine volcano in southern Alaska began erupting after 20-year repose. The Anchorage Forecast Office of the National Weather Service (NWS) issued an advisory on 28 January for Kodiak City. On 31 January, Alaska Airlines cancelled all flights to and from Anchorage after multiple advisories from the NWS for Anchorage and the surrounding region. The Alaska Volcano Observatory (AVO) had reported the onset of the continuous eruption. AVO monitors the approximately 100 active volcanoes in the Northern Pacific. Ash clouds from these volcanoes can cause serious damage to an aircraft and pose a serious threat tomore » the local communities, and to transcontinental air traffic throughout the Arctic and sub-Arctic region. Within AVO, a dispersion model has been developed to track the dispersion of volcanic ash clouds. The model, Puff, was used operational by AVO during the Augustine eruptive period. Here, we examine the dispersion of a volcanic ash cloud from Mount Augustine across Alaska from 29 January through the 2 February 2006. We present the synoptic meteorology, the Puff predictions, and measurements from aerosol samplers, laser radar (or lidar) systems, and satellites. UAF aerosol samplers revealed the presence of volcanic aerosols at the surface at sites where Puff predicted the ash clouds movement. Remote sensing satellite data showed the development of the ash cloud in close proximity to the volcano and a sulfur-dioxide cloud further from the volcano consistent with the Puff predictions. Lidars showed the presence of volcanic aerosol with consistent characteristics aloft over Alaska and were capable of detecting the aerosol, even in the presence of scattered clouds and where the cloud is too thin/disperse to be detected by remote sensing satellite data. The lidar measurements revealed the different trajectories of ash consistent with the Puff predictions. Dispersion models provide a forecast of volcanic ash cloud movement that might be undetectable by any other means but are still a significant hazard. Validation is the key to assessing the accuracy of any future predictions. The study highlights the use of multiple and complementary observations used in detecting the trajectory ash cloud, both at the surface and aloft within the atmosphere.« less

On The Development of One-way Nesting of Air-pollution Model Smog Into Numerical Weather Prediction Model Eta

NASA Astrophysics Data System (ADS)

Halenka, T.; Bednar, J.; Brechler, J.

The spatial distribution of air pollution on the regional scale (Bohemian region) is simulated by means of Charles University puff model SMOG. The results are used for the assessment of the concentration fields of ozone, nitrogen oxides and other ozone precursors. Current improved version of the model covers up to 16 groups of basic compounds and it is based on trajectory computation and puff interaction both by means of Gaussian diffusion mixing and chemical reactions of basic species. Gener- ally, the method used for trajectory computation is valuable mainly for episodes sim- ulation, nevertheless, climatological study can be solved as well by means of average wind rose. For the study being presented huge database of real emission sources was incorporated with all kind of sources included. Some problem with the background values of concentrations was removed. The model SMOG has been nested into the forecast model ETA to obtain appropriate meteorological data input. We can estimate air pollution characteristics both for episodes analysis and the prediction of future air quality conditions. Necessary prognostic variables from the numerical weather pre- diction model are taken for the region of the central Bohemia, where the original puff model was tested. We used mainly 850 hPa wind field for computation of prognos- tic trajectories, the influence of surface temperature as a parameter of photochemistry reactions as well as the effect of cloudness has been tested.

An integrated model-based approach to the risk assessment of pesticide drift from vineyards

NASA Astrophysics Data System (ADS)

Pivato, Alberto; Barausse, Alberto; Zecchinato, Francesco; Palmeri, Luca; Raga, Roberto; Lavagnolo, Maria Cristina; Cossu, Raffaello

2015-06-01

The inhalation of pesticide in air is of particular concern for people living in close contact with intensive agricultural activities. This study aims to develop an integrated modelling methodology to assess whether pesticides pose a risk to the health of people living near vineyards, and apply this methodology in the world-renowned Prosecco DOCG (Italian label for protection of origin and geographical indication of wines) region. A sample field in Bigolino di Valdobbiadene (North-Eastern Italy) was selected to perform the pesticide fate modellization and the consequent inhalation risk assessment for people living in the area. The modellization accounts for the direct pesticide loss during the treatment of vineyards and for the volatilization from soil after the end of the treatment. A fugacity model was used to assess the volatilization flux from soil. The Gaussian puff air dispersion model CALPUFF was employed to assess the airborne concentration of the emitted pesticide over the simulation domain. The subsequent risk assessment integrates the HArmonised environmental Indicators for pesticide Risk (HAIR) and US-EPA guidelines. In this case study the modelled situation turned to be safe from the point of view of human health in the case of non-carcinogenic compounds, and additional improvements were suggested to further mitigate the effect of the most critical compound.

Transport phenomena governing nicotine emissions from electronic cigarettes: model formulation and experimental investigation

PubMed Central

Talih, Soha; Balhas, Zainab; Salman, Rola; El-Hage, Rachel; Karaoghlanian, Nareg; El-Hellani, Ahmad; Baassiri, Mohamad; Jaroudi, Ezzat; Eissenberg, Thomas; Saliba, Najat; Shihadeh, Alan

2017-01-01

Electronic cigarettes (ECIGs) electrically heat and aerosolize a liquid containing propylene glycol (PG), vegetable glycerin (VG), flavorants, water, and nicotine. ECIG effects and proposed methods to regulate them are controversial. One regulatory focal point involves nicotine emissions. We describe a mathematical model that predicts ECIG nicotine emissions. The model computes the vaporization rate of individual species by numerically solving the unsteady species and energy conservation equations. To validate model predictions, yields of nicotine, total particulate matter, PG, and VG were measured while manipulating puff topography, electrical power, and liquid composition across 100 conditions. Nicotine flux, the rate at which nicotine is emitted per unit time, was the primary outcome. Across conditions, the measured and computed nicotine flux were highly correlated (r = 0.85, p<.0001). As predicted, device power, nicotine concentration, PG/VG ratio, and puff duration influenced nicotine flux (p<.05), while water content and puff velocity did not. Additional empirical investigation revealed that PG/VG liquids act as ideal solutions, that liquid vaporization accounts for more than 95% of ECIG aerosol mass emissions, and that as device power increases the aerosol composition shifts towards the less volatile components of the parent liquid. To the extent that ECIG regulations focus on nicotine emissions, mathematical models like this one can be used to predict ECIG nicotine emissions and to test the effects of proposed regulation of factors that influence nicotine flux. PMID:28706340

Measurement of nitrogen dioxide in cigarette smoke using quantum cascade tunable infrared laser differential absorption spectroscopy (TILDAS)

NASA Astrophysics Data System (ADS)

Shorter, Joanne H.; Nelson, David D.; Zahniser, Mark S.; Parrish, Milton E.; Crawford, Danielle R.; Gee, Diane L.

2006-04-01

Although nitrogen dioxide (NO 2) has been previously reported to be present in cigarette smoke, the concentration estimates were derived from kinetic calculations or from measurements of aged smoke, where NO 2 was formed some time after the puff was taken. The objective of this work was to use tunable infrared laser differential absorption spectroscopy (TILDAS) equipped with a quantum cascade (QC) laser to determine if NO 2 could be detected and quantified in a fresh puff of cigarette smoke. A temporal resolution of ˜0.16 s allowed measurements to be taken directly as the NO 2 was formed during the puff. Sidestream cigarette smoke was sampled to determine if NO 2 could be detected using TILDAS. Experiments were conducted using 2R4F Kentucky Reference cigarettes with and without a Cambridge filter pad. NO 2 was detected only in the lighting puff of whole mainstream smoke (without a Cambridge filter pad), with no NO 2 detected in the subsequent puffs. The measurement precision was ˜1.0 ppbV Hz -1/2, which allows a detection limit of ˜0.2 ng in a 35 ml puff volume. More NO 2 was generated in the lighting puff using a match or blue flame lighter (29 ± 21 ng) than when using an electric lighter (9 ± 3 ng). In the presence of a Cambridge filter pad, NO 2 was observed in the gas phase mainstream smoke for every puff (total of 200 ± 30 ng/cigarette) and is most likely due to smoke chemistry taking place on the Cambridge filter pad during the smoke collection process. Nitrogen dioxide was observed continuously in the sidestream smoke starting with the lighting puff.

Nespoli performs periodic maintenance on the PuFF Experiment

NASA Image and Video Library

2011-02-14

ISS026-E-027009 (14 Feb. 2011) --- European Space Agency (ESA) astronaut Paolo Nespoli, Expedition 26 flight engineer, performs periodic maintenance on the Pulmonary Function in Flight (PuFF) experiment by re-greasing the PuFF calibration syringe in the Columbus laboratory of the International Space Station.

Pulmonary Function in Flight (PuFF) Experiment

NASA Technical Reports Server (NTRS)

2003-01-01

In this International Space Station (ISS) onboard photo, Expedition Six Science Officer Donald R. Pettit works to set up the Pulmonary Function in Flight (PuFF) experiment hardware in the Destiny Laboratory. Expedition Six is the fourth and final crew to perform the PuFF experiment. The PuFF experiment was developed to better understand what effects long term exposure to microgravity may have on the lungs. The focus is on measuring changes in the everness of gas exchange in the lungs, and on detecting changes in respiratory muscle strength. It allows astronauts to measure blood flow through the lungs, the ability of the lung to take up oxygen, and lung volumes. Each PuFF session includes five lung function tests, which involve breathing only cabin air. For each planned extravehicular (EVA) activity, a crew member performs a PuFF test within one week prior to the EVA. Following the EVA, those crew members perform another test to document the effect of exposure of the lungs to the low-pressure environment of the space suits. This experiment utilizes the Gas Analyzer System for Metabolic Analysis Physiology, or GASMAP, located in the Human Research Facility (HRF), along with a variety of other Puff equipment including a manual breathing valve, flow meter, pressure-flow module, pressure and volume calibration syringes, and disposable mouth pieces.

Optimization of Fat-Reduced Puff Pastry Using Response Surface Methodology.

PubMed

Silow, Christoph; Zannini, Emanuele; Axel, Claudia; Belz, Markus C E; Arendt, Elke K

2017-02-22

Puff pastry is a high-fat bakery product with fat playing a key role, both during the production process and in the final pastry. In this study, response surface methodology (RSM) was successfully used to evaluate puff pastry quality for the development of a fat-reduced version. The technological parameters modified included the level of roll-in fat, the number of fat layers (50-200) and the final thickness (1.0-3.5 mm) of the laminated dough. Quality characteristics of puff pastry were measured using the Texture Analyzer with an attached Extended Craft Knife (ECK) and Multiple Puncture Probe (MPP), the VolScan and the C-Cell imaging system. The number of fat layers and final dough thickness, in combination with the amount of roll-in fat, had a significant impact on the internal and external structural quality parameters. With technological changes alone, a fat-reduced (≥30%) puff pastry was developed. The qualities of fat-reduced puff pastries were comparable to conventional full-fat (33 wt %) products. A sensory acceptance test revealed no significant differences in taste of fatness or 'liking of mouthfeel'. Additionally, the fat-reduced puff pastry resulted in a significant ( p < 0.05) positive correlation to 'liking of flavor' and overall acceptance by the assessors.

Optimization of Fat-Reduced Puff Pastry Using Response Surface Methodology

PubMed Central

Silow, Christoph; Zannini, Emanuele; Axel, Claudia; Belz, Markus C. E.; Arendt, Elke K.

2017-01-01

Puff pastry is a high-fat bakery product with fat playing a key role, both during the production process and in the final pastry. In this study, response surface methodology (RSM) was successfully used to evaluate puff pastry quality for the development of a fat-reduced version. The technological parameters modified included the level of roll-in fat, the number of fat layers (50–200) and the final thickness (1.0–3.5 mm) of the laminated dough. Quality characteristics of puff pastry were measured using the Texture Analyzer with an attached Extended Craft Knife (ECK) and Multiple Puncture Probe (MPP), the VolScan and the C-Cell imaging system. The number of fat layers and final dough thickness, in combination with the amount of roll-in fat, had a significant impact on the internal and external structural quality parameters. With technological changes alone, a fat-reduced (≥30%) puff pastry was developed. The qualities of fat-reduced puff pastries were comparable to conventional full-fat (33 wt %) products. A sensory acceptance test revealed no significant differences in taste of fatness or ‘liking of mouthfeel’. Additionally, the fat-reduced puff pastry resulted in a significant (p < 0.05) positive correlation to ‘liking of flavor’ and overall acceptance by the assessors. PMID:28231095

Flow behavior of N2 huff and puff process for enhanced oil recovery in tight oil reservoirs.

PubMed

Lu, Teng; Li, Zhaomin; Li, Jian; Hou, Dawei; Zhang, Dingyong

2017-11-16

In the present work, the potential of N 2 huff and puff process to enhance the recovery of tight oil reservoir was evaluated. N 2 huff and puff experiments were performed in micromodels and cores to investigate the flow behaviors of different cycles. The results showed that, in the first cycle, N 2 was dispersed in the oil, forming the foamy oil flow. In the second cycle, the dispersed gas bubbles gradually coalesced into the continuous gas phase. In the third cycle, N 2 was produced in the form of continuous gas phase. The results from the coreflood tests showed that, the primary recovery was only 5.32%, while the recoveries for the three N 2 huff and puff cycles were 15.1%, 8.53% and 3.22%, respectively.The recovery and the pressure gradient in the first cycle were high. With the increase of huff and puff cycles, and the oil recovery and the pressure gradient rapidly decreased. The oil recovery of N 2 huff and puff has been found to increase as the N 2 injection pressure and the soaking time increased. These results showed that, the properly designed and controlled N 2 huff and puff process can lead to enhanced recovery of tight oil reservoirs.

E-cigarettes generate high levels of aldehydes only in 'dry puff' conditions.

PubMed

Farsalinos, Konstantinos E; Voudris, Vassilis; Poulas, Konstantinos

2015-08-01

Aldehydes are emitted by electronic cigarettes due to thermal decomposition of liquid components. Although elevated levels have been reported with new-generation high-power devices, it is unclear whether they are relevant to true exposure of users (vapers) because overheating produces an unpleasant taste, called a dry puff, which vapers learn to avoid. The aim was to evaluate aldehyde emissions at different power levels associated with normal and dry puff conditions. Two customizable atomizers were prepared so that one (A1) had a double wick, resulting in high liquid supply and lower chance of overheating at high power levels, while the other (A2) was a conventional setup (single wick). Experienced vapers took 4-s puffs at 6.5 watts (W), 7.5 W, 9 W and 10 W power levels with both atomizers and were asked to report whether dry puffs were generated. The atomizers were then attached to a smoking machine and aerosol was trapped. Clinic office and analytical chemistry laboratory in Greece. Seven experienced vapers. Aldehyde levels were measured in the aerosol. All vapers identified dry puff conditions at 9 W and 10 W with A2. A1 did not lead to dry puffs at any power level. Minimal amounts of aldehydes per 10 puffs were found at all power levels with A1 (up to 11.3 µg for formaldehyde, 4.5 µg for acetaldehyde and 1.0 µg for acrolein) and at 6.5 W and 7.5 W with A2 (up to 3.7 µg for formaldehyde, 0.8 µg for acetaldehyde and 1.3 µg for acrolein). The levels were increased by 30 to 250 times in dry puff conditions (up to 344.6 µg for formaldehyde, 206.3 µg for acetaldehyde and 210.4 µg for acrolein, P < 0.001), while acetone was detected only in dry puff conditions (up to 22.5 µg). Electronic cigarettes produce high levels of aldehyde only in dry puff conditions, in which the liquid overheats, causing a strong unpleasant taste that e-cigarette users detect and avoid. Under normal vaping conditions aldehyde emissions are minimal, even in new-generation high-power e-cigarettes. © 2015 Society for the Study of Addiction.

REINFORCING EFFECTS OF NICOTINE AND NON-NICOTINE COMPONENTS OF CIGARETTE SMOKE

PubMed Central

Rose, Jed E.; Salley, Al; Behm, Frederique M.; Bates, James E.; Westman, Eric C.

2014-01-01

We assessed the reinforcing effects of nicotine and non-nicotine components of cigarette smoke, by presenting a concurrent choice paradigm in which participants had access to intravenous (IV) nicotine infusions vs. saline (placebo) infusions and puffs from denicotinized (“denic”) cigarettes vs. air (sham puffs). We also measured the effects on self-administration of prior satiation with each component. Sixteen smokers participated in 7 sessions, consisting of: 1) a baseline smoking assessment, which was used to tailor the nicotine dose per infusion to that of puffs from subjects’ preferred brands of cigarettes; 2) two sessions in which participants were trained to discriminate IV nicotine vs. saline infusions and denic smoke vs. sham (air) puffs; and 3) four sessions assessing choice behavior after different satiation conditions. Results showed that subjects self-administered more puffs of denic smoke than any other alternative, including IV nicotine. IV nicotine, however, was preferred over IV saline and sham puffs. Preference for denic smoke vs. IV nicotine was highly correlated with subjective ratings of “comfort” associated with the two alternatives. Satiation with smoke diminished the number of denic puffs taken during choice periods, while prior administration of nicotine did not affect the number of puffs taken. Smoking withdrawal symptoms were alleviated both by nicotine administration and by denic smoke. These results show that in established smokers, non-nicotine aspects of cigarette smoking have potent reinforcing effects. While current smoking cessation pharmacotherapies primarily address the nicotine component of cigarette addiction, future cessation strategies should also be designed to target non-nicotine factors. PMID:20358364

Phase-resolved and time-averaged puff motions of an excited stack-issued transverse jet

NASA Astrophysics Data System (ADS)

Hsu, C. M.; Huang, R. F.

2013-07-01

The dynamics of puff motions in an excited stack-issued transverse jet were studied experimentally in a wind tunnel. The temporal and spatial evolution processes of the puffs induced by acoustic excitation were examined using the smoke flow visualization method and high-speed particle image velocimetry. The temporal and spatial evolutions of the puffs were examined using phase-resolved ensemble-averaged velocity fields and the velocity, length scales, and vorticity characteristics of the puffs were studied. The time-averaged velocity fields were calculated to analyze the velocity distributions and vorticity contours. The results show that a puff consists of a pair of counter-rotating vortex rings. An initial vortex ring was formed due to a concentration of vorticity at the lee side of the issuing jet at the instant of the mid-oscillation cycle. A vortex ring rotating in the opposite direction to that of the initial vortex ring was subsequently formed at the upwind side of the issuing jet. These two counter-rotating vortex rings formed a "mushroom" vortex pair, which was deflected by the crossflow and traveled downstream along a time-averaged trajectory of zero vorticity. The trajectory was situated far above the time-averaged streamline evolving from the leading edge of the tube. The velocity magnitudes of the vortex rings at the upwind and the lee side decreased with time evolution as the puffs traveled downstream due to momentum dissipation and entrainment effects. The puffs traveling along the trajectory of zero vorticity caused large velocities to appear above the leading-edge streamline.

Effect of salt reduction on wheat-dough properties and quality characteristics of puff pastry with full and reduced fat content.

PubMed

Silow, Christoph; Zannini, Emanuele; Axel, Claudia; Lynch, Kieran M; Arendt, Elke K

2016-11-01

Puff pastry is a major contributor of fat and sodium intake in many countries. The objective of this research was to determine the impact of salt (0-8.4g/100g flour) on the structure and quality characteristics of puff pastry with full and reduced (-40%) fat content as well as the rheological properties of the resulting dough. Therefore, empirical rheological tests were carried out including dough extensibility, dough stickiness and GlutoPeak test. The quality of the puff pastry was characterized with the VolScan, Texture Analyzer and C-Cell. NaCl reduction significantly changed rheological properties of the basic dough as well as a number of major quality characteristics of the puff pastry. Significant differences due to NaCl addition were found in particular for dough resistance, dough stickiness, Peak Maximum Time and Maximum Torque (p<0.05). Peak firmness and total firmness decreased significantly (p<0.05) with increasing salt levels for puff pastry containing full fat. Likewise, maximal lift, specific volume, number of cells and slice brightness increased with increasing NaCl at both fat levels. Although a sensorial comparison of puff pastries revealed that salt reduction (30%) was perceptible, no significant differences were found for all other investigated attributes. Nevertheless, a reduction of 30% salt and 40% fat in puff pastry is achievable as neither the perception and visual impression nor attributes such as volume, firmness and flavour of the final products were significantly affected. Copyright © 2016 Elsevier Ltd. All rights reserved.

Variability in Puff Topography and Exhaled CO in Waterpipe Tobacco Smoking.

PubMed

Kim, Hyoshin; Brinkman, Marielle C; Sharma, Eva; Gordon, Sydney M; Clark, Pamela I

2016-10-01

We examined intra-individual variability in puff topography and CO measures collected during laboratory waterpipe (WP) tobacco smoking using a research-grade waterpipe (RWP). WP smoking topography and exhaled CO measures were obtained from 10 established WP smokers in a single-blind, crossover design. Using a previously validated RWP, each participant smoked "Two Apples" WP tobacco ad libitum with a single quick-light charcoal to satiation in 3 laboratory sessions spaced at least one week apart. To examine the intra-individual variability, the intraclass correlation coefficient ( ρ ) for topography and CO measures were estimated. Results: The majority of the topography and CO measures were stable. Most stable were puff frequency ( ρ = 0.88), number of puffs ( ρ = 0.86), and puff duration (ρ = 0.80). Less stable were peak flow ( ρ = 0.57) and total puff volume ( ρ = 0.52). The results provide the first set of empirical evidence that most topography and CO measurements collected using the RWP from a single laboratory smoking session are stable such that they can be representative of a smoker's puffing behaviors and reproducible among 3 sessions spread equally across 3 weeks.

The Pulsed Fission-Fusion (PUFF) Concept for Deep Space Exploration and Terrestrial Power Generation

NASA Technical Reports Server (NTRS)

Adams, Robert; Cassibry, Jason; Schillo, Kevin

2017-01-01

This team is exploring a modified Z-pinch geometry as a propulsion system, imploding a liner of liquid lithium onto a pellet containing both fission and fusion fuel. The plasma resulting from the fission and fusion burn expands against a magnetic nozzle, for propulsion, or a magnetic confinement system, for terrestrial power generation. There is considerable synergy in the concept; the lithium acts as a temporary virtual cathode, and adds reaction mass for propulsion. Further, the lithium acts as a radiation shield against generated neutrons and gamma rays. Finally, the density profile of the column can be tailored using the lithium sheath. Recent theoretical and experimental developments (e.g. tailored density profile in the fuel injection, shear stabilization, and magnetic shear stabilization) have had great success in mitigating instabilities that have plagued previous fusion efforts. This paper will review the work in evaluating the pellet sizes and z-pinch conditions for optimal PuFF propulsion. Trades of pellet size and composition with z-pinch power levels and conditions for the tamper and lithium implosion are evaluated. Current models, both theoretical and computational, show that a z-pinch can ignite a small (1 cm radius) fission-fusion target with significant yield. Comparison is made between pure fission and boosted fission targets. Performance is shown for crewed spacecraft for high speed Mars round trip missions and near interstellar robotic missions. The PuFF concept also offers a solution for terrestrial power production. PuFF can, with recycling of the effluent, achieve near 100% burnup of fission fuel, providing a very attractive power source with minimal waste. The small size of PuFF relative to today's plants enables a more distributed power network and less exposure to natural or man-made disruptions.

Research on plasma-puff initiation of high Coulomb transfer switches

NASA Technical Reports Server (NTRS)

Venable, Demetrius D.; Han, Kwang S.

1993-01-01

The plasma-puff triggering mechanism based on hypocycloidal pinch geometry was investigated to determine the optimal operating conditions for an azimuthally uniform surface flashover which initiates plasma-puff under wide ranges of fill gas pressures of Ar, He and N2. Research is presented and resulting conference papers are attached. These papers include 'Characteristics of Plasma-Puff Trigger for an Inverse-Pinch Plasma Switch'; 'Ultra-High-Power Plasma Switch INPUTS for Pulse Power Systems'; 'Characteristics of Switching Plasma in an Inverse-Pinch Switch'; 'Comparative Study of INPIStron and Spark Gap'; and 'INPIStron Switched Pulsed Power for Dense Plasma Pinches.'

Studies of the Plasma Triggering Mechanism of Inverse Pinch Switch

DTIC Science & Technology

1993-11-10

plasma - focus driven plasma-puff was also discussed in comparison with the hypocycloidal pinch plasma-puff triggering. The main discharge of inverse pinch switch with plasma - focus driven plasma-puff trigger is found to be more azimuthally uniform than that with hypocycloidal pinch plasma-puff trigger in a gas pressure region between 80 mTorr and 1 Torr. A comparative study of the INPIStron and a spark gap also reveals that the INPIStron with a low impedance Z = 9 ohms can transfer a high voltage pulse with a superior pulse-shape fidelity over that with

Differing ERP patterns caused by suction and puff stimuli.

PubMed

Choi, Mi-Hyun; Kim, Hyung-Sik; Baek, Ji-Hye; Lee, Jung-Chul; Park, Sung-Jun; Jeong, Ul-Ho; Gim, Seon-Young; You, Ji Hye; Kim, Sung-Pil; Lim, Dae-Woon; Kim, Hyun-Jun; Chung, Soon-Cheol

2015-05-06

The present study compared event-related potential (ERP) patterns for two stimuli types, puff and suction, by applying these stimuli to the fingers; ERP patterns for the two stimuli were compared at C3, an area related to somatosensory perception, and at FC5, an area related to motor function. Participants were 12 healthy males in their 20s (mean age=23.1±2.0 years). One session consisted of a Control Phase (3s), a Stimulation Phase (3s), and a Rest Phase (9s). During the Stimulation Phase, a 4-psi suction or puff stimulus was applied to the first joint of the right index finger. After completion of the session, a subjective magnitude test was presented. In all phases, electroencephalography signals were recorded. We extracted maximum positive amplitude and minimum negative amplitude as well as relevant latency values for C3 and FC5 signals. Suction and puff stimuli had similar subjective magnitude scores. For both C3 and FC5, the maximum and minimum amplitude latency was reached earlier for the suction stimulus than for the puff stimulus. In conclusion, when suction and puff stimuli of the same intensity were applied to the fingers, the suction stimulus caused a more sensitive response in the somatosensory area (C3) and motor area (FC5) than did the puff stimulus. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Preliminary Results of an Examination of Electronic Cigarette User Puff Topography: The Effect of a Mouthpiece-Based Topography Measurement Device on Plasma Nicotine and Subjective Effects

PubMed Central

Spindle, Tory R.; Breland, Alison B.; Karaoghlanian, Nareg V.; Shihadeh, Alan L.

2015-01-01

Introduction: Electronic cigarettes (ECIGs) heat a nicotine-containing solution; the resulting aerosol is inhaled by the user. Nicotine delivery may be affected by users’ puffing behavior (puff topography), and little is known about the puff topography of ECIG users. Puff topography can be measured using mouthpiece-based computerized systems. However, the extent to which a mouthpiece influences nicotine delivery and subjective effects in ECIG users is unknown. Methods: Plasma nicotine concentration, heart rate, and subjective effects were measured in 13 experienced ECIG users who used their preferred ECIG and liquid (≥12mg/ml nicotine) during 2 sessions (with or without a mouthpiece). In both sessions, participants completed an ECIG use session in which they were instructed to take 10 puffs with 30-second inter-puff intervals. Puff topography was recorded in the mouthpiece condition. Results: Almost all measures of the effects of ECIG use were independent of topography measurement. Collapsed across session, mean plasma nicotine concentration increased by 16.8ng/ml, and mean heart rate increased by 8.5 bpm (ps < .05). Withdrawal symptoms decreased significantly after ECIG use. Participants reported that the mouthpiece affected awareness and made ECIG use more difficult. Relative to previously reported data for tobacco cigarette smokers using similar topography measurement equipment, ECIG-using participants took larger and longer puffs with lower flow rates. Conclusions: In experienced ECIG users, measuring ECIG topography did not influence ECIG-associated nicotine delivery or most measures of withdrawal suppression. Topography measurement systems will need to account for the low flow rates observed for ECIG users. PMID:25239957

Preliminary results of an examination of electronic cigarette user puff topography: the effect of a mouthpiece-based topography measurement device on plasma nicotine and subjective effects.

PubMed

Spindle, Tory R; Breland, Alison B; Karaoghlanian, Nareg V; Shihadeh, Alan L; Eissenberg, Thomas

2015-02-01

Electronic cigarettes (ECIGs) heat a nicotine-containing solution; the resulting aerosol is inhaled by the user. Nicotine delivery may be affected by users' puffing behavior (puff topography), and little is known about the puff topography of ECIG users. Puff topography can be measured using mouthpiece-based computerized systems. However, the extent to which a mouthpiece influences nicotine delivery and subjective effects in ECIG users is unknown. Plasma nicotine concentration, heart rate, and subjective effects were measured in 13 experienced ECIG users who used their preferred ECIG and liquid (≥ 12 mg/ml nicotine) during 2 sessions (with or without a mouthpiece). In both sessions, participants completed an ECIG use session in which they were instructed to take 10 puffs with 30-second inter-puff intervals. Puff topography was recorded in the mouthpiece condition. Almost all measures of the effects of ECIG use were independent of topography measurement. Collapsed across session, mean plasma nicotine concentration increased by 16.8 ng/ml, and mean heart rate increased by 8.5 bpm (ps < .05). Withdrawal symptoms decreased significantly after ECIG use. Participants reported that the mouthpiece affected awareness and made ECIG use more difficult. Relative to previously reported data for tobacco cigarette smokers using similar topography measurement equipment, ECIG-using participants took larger and longer puffs with lower flow rates. In experienced ECIG users, measuring ECIG topography did not influence ECIG-associated nicotine delivery or most measures of withdrawal suppression. Topography measurement systems will need to account for the low flow rates observed for ECIG users. © The Author 2014. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Computational modeling of Krypton gas puffs with tailored mass density profiles on Z

DOE PAGES

Jennings, Christopher A.; Ampleford, David J.; Lamppa, Derek C.; ...

2015-05-18

Large diameter multi-shell gas puffs rapidly imploded by high current (~20 MA, ~100 ns) on the Z generator of Sandia National Laboratories are able to produce high-intensity Krypton K-shell emission at ~13 keV. Efficiently radiating at these high photon energies is a significant challenge which requires the careful design and optimization of the gas distribution. To facilitate this, we hydrodynamically model the gas flow out of the nozzle and then model its implosion using a 3-dimensional resistive, radiative MHD code (GORGON). This approach enables us to iterate between modeling the implosion and gas flow from the nozzle to optimize radiativemore » output from this combined system. Furthermore, guided by our implosion calculations, we have designed gas profiles that help mitigate disruption from Magneto-Rayleigh–Taylor implosion instabilities, while preserving sufficient kinetic energy to thermalize to the high temperatures required for K-shell emission.« less

Enhancing the x-ray output of a single-wire explosion with a gas-puff based plasma opening switch

NASA Astrophysics Data System (ADS)

Engelbrecht, Joseph T.; Ouart, Nicholas D.; Qi, Niansheng; de Grouchy, Philip W.; Shelkovenko, Tatiana A.; Pikuz, Sergey A.; Banasek, Jacob T.; Potter, William M.; Rocco, Sophia V.; Hammer, David A.; Kusse, Bruce R.; Giuliani, John L.

2018-02-01

We present experiments performed on the 1 MA COBRA generator using a low density, annular, gas-puff z-pinch implosion as an opening switch to rapidly transfer a current pulse into a single metal wire on axis. This gas-puff on axial wire configuration was studied for its promise as an opening switch and as a means of enhancing the x-ray output of the wire. We demonstrate that current can be switched from the gas-puff plasma into the wire, and that the timing of the switch can be controlled by the gas-puff plenum backing pressure. X-ray detector measurements indicate that for low plenum pressure Kr or Xe shots with a copper wire, this configuration can offer a significant enhancement in the peak intensity and temporal distribution of radiation in the 1-10 keV range.

Electron particle transport and turbulence studies in the T-10 tokamak

NASA Astrophysics Data System (ADS)

Vershkov, V. A.; Borisov, M. A.; Subbotin, G. F.; Shelukhin, D. A.; Dnestrovskii, Yu. N.; Danilov, A. V.; Cherkasov, S. V.; Gorbunov, E. P.; Sergeev, D. S.; Grashin, S. A.; Krylov, S. V.; Kuleshin, E. O.; Myalton, T. B.; Skosyrev, Yu. V.; Chistiakov, V. V.

2013-08-01

The goals of this paper are to compare the results of electron particle transport measurements in ohmic (OH) plasmas by means of a small perturbation technique, high-level gas puff and gas switch off, investigate the phenomenon of ‘density pump out’ during electron cyclotron resonance heating (ECRH) and to correlate density behaviour with turbulence. Two approaches for plasma particle transport studies were compared: the low perturbation technique of periodic puff (δn/ne = 0.3%) and strong density variations (δn/ne < 50%), including density ramp-up by gas puff and ramp-down with gas switch off. The model with constant in time diffusion coefficients and pinch velocities could describe the core density perturbations but failed at the edge. In the case of strong puff three stages were distinguished. Degraded energy confinement and, respectively, low turbulence frequencies were observed during density ramp-up and ramp-down, while enhanced confinement and higher turbulence frequencies were typical for the intermediate stage. Density profile variation during this intermediate phase could be described in the framework of the transport model with constant in time coefficients. The application of ECRH at the density ramp-up phase provided the possibility of postponing the ‘density pump out’. The increase in the low-frequency modes in turbulence spectra was observed at the ‘density pump out’ phase during central ECRH. Although the high- and low-frequency bands of turbulence spectra behaved as trapped electron mode and ion temperature gradient, respectively, they both rotated at the same angular velocity as a rigid body together with magnetohydrodynamic mode m/n = 2/1 and [E × B] plasma rotation.

Effect of e-liquid flavor on electronic cigarette topography and consumption behavior in a 2-week natural environment switching study.

PubMed

Robinson, R J; Hensel, E C; Al-Olayan, A A; Nonnemaker, J M; Lee, Y O

2018-01-01

Electronic Nicotine Delivery Systems (ENDS) offer an alternate means to consume nicotine in a variety of flavored aerosols. Data are needed to better understand the impact of flavors on use behavior. A natural environment observational study was conducted on experienced ENDS users to measure the effect of e-liquid flavor on topography and consumption behavior. The RIT wPUMTM monitor was used to record to record the date and time and puff topography (flow rate, volume, duration) for every puff taken by N = 34 participants over the course of two weeks. All participants used tobacco flavor for one week, and either berry or menthol flavor for one week. Results provide strong evidence that flavor affects the topography behaviors of mean puff flow rate and mean puff volume, and there is insufficient evidence to support an influence of flavor on mean puff duration and mean puff interval. There was insufficient evidence, due to the low power associated with the limited number of observation days, to establish a relationship between flavor and cumulative consumption behavior. While the results indicate that an effect may be evident, additional observation days are required to establish significance.

Effect of e-liquid flavor on electronic cigarette topography and consumption behavior in a 2-week natural environment switching study

PubMed Central

al-Olayan, A. A.; Nonnemaker, J. M.; Lee, Y. O.

2018-01-01

Electronic Nicotine Delivery Systems (ENDS) offer an alternate means to consume nicotine in a variety of flavored aerosols. Data are needed to better understand the impact of flavors on use behavior. A natural environment observational study was conducted on experienced ENDS users to measure the effect of e-liquid flavor on topography and consumption behavior. The RIT wPUMTM monitor was used to record to record the date and time and puff topography (flow rate, volume, duration) for every puff taken by N = 34 participants over the course of two weeks. All participants used tobacco flavor for one week, and either berry or menthol flavor for one week. Results provide strong evidence that flavor affects the topography behaviors of mean puff flow rate and mean puff volume, and there is insufficient evidence to support an influence of flavor on mean puff duration and mean puff interval. There was insufficient evidence, due to the low power associated with the limited number of observation days, to establish a relationship between flavor and cumulative consumption behavior. While the results indicate that an effect may be evident, additional observation days are required to establish significance. PMID:29718974

Puff and bite: the relationship between the glucocorticoid stress response and anti-predator performance in checkered puffer (Sphoeroides testudineus).

PubMed

Cull, Felicia; O'Connor, Constance M; Suski, Cory D; Shultz, Aaron D; Danylchuk, Andy J; Cooke, Steven J

2015-04-01

Individual variation in the endocrine stress response has been linked to survival and performance in a variety of species. Here, we evaluate the relationship between the endocrine stress response and anti-predator behaviors in wild checkered puffers (Sphoeroides testudineus) captured at Eleuthera Island, Bahamas. The checkered puffer has a unique and easily measurable predator avoidance strategy, which is to inflate or 'puff' to deter potential predators. In this study, we measured baseline and stress-induced circulating glucocorticoid levels, as well as bite force, a performance measure that is relevant to both feeding and predator defence, and 'puff' performance. We found that puff performance and bite force were consistent within individuals, but generally decreased following a standardized stressor. Larger puffers were able to generate a higher bite force, and larger puffers were able to maintain a more robust puff performance following a standardized stressor relative to smaller puffers. In terms of the relationship between the glucocorticoid stress response and performance metrics, we found no relationship between post-stress glucocorticoid levels and either puff performance or bite force. However, we did find that baseline glucocorticoid levels predicted the ability of a puffer to maintain a robust puff response following a repeated stressor, and this relationship was more pronounced in larger individuals. Our work provides a novel example of how baseline glucocorticoids can predict a fitness-related anti-predator behavior. Copyright © 2015 Elsevier Inc. All rights reserved.

Make your own cigarettes: toxicant exposure, smoking topography, and subjective effects.

PubMed

Koszowski, Bartosz; Rosenberry, Zachary R; Viray, Lauren C; Potts, Jennifer L; Pickworth, Wallace B

2014-09-01

Despite considerable use of make your own (MYO) cigarettes worldwide and increasing use in the United States, relatively little is known about how these cigarettes are smoked and the resultant toxicant exposure. In a laboratory study, we compared two types of MYO cigarettes-roll your own (RYO) and personal machine made (PMM)-with factory-made (FM) cigarettes in three groups of smokers who exclusively used RYO (n = 34), PMM (n = 23), or FM (n = 20). Within each group, cigarettes were smoked in three conditions: (i) after confirmed overnight tobacco abstinence; (ii) in an intense smoking paradigm; and (iii) without restrictions. All cigarettes were smoked ad lib through a smoking topography unit. Plasma nicotine significantly increased after cigarettes in all conditions except PMM in the intense smoking paradigm. Puff volume, puff duration, total puff volume, and puff velocity did not differ between cigarette types but the puffs per cigarette and time to smoke were significantly smaller for RYO compared with PMM and FM. Regardless of the cigarette, participants consumed the first three puffs more vigorously than the last three puffs. Despite the belief of many of their consumers, smoking MYO cigarettes is not a safe alternative to FM cigarettes. Like FM, MYO cigarettes expose their users to harmful constituents of tobacco smoke. Despite differences in size and design their puffing profiles are remarkably similar. These data are relevant to health and regulatory considerations on the MYO cigarettes. ©2014 American Association for Cancer Research.

Are glass fiber particles released during the use of electronic cigarettes? Development of a semi-quantitative approach to detect glass particle emission due to vaping.

PubMed

Shin, Jae-Won; Jo, Sang-Hee; Kim, Ki-Hyun; Song, Hee-Nam; Kang, Chang-Hee; Bolan, Nanthi; Hong, Jongki

2018-05-04

This study investigated the emission characteristics of glass particles resulting from smoking electronic cigarettes (ECs). First, the most suitable filter for the collection of glass particles was explored by examining the performance (reliability) of various types of filters. A polycarbonate filter was determined as the optimum choice to collect glass particles in EC aerosol. A cartomizer was filled with EC refill solution composed of an equal volume of propylene glycol (PG) and vegetable glycol (VG). To simulate the potential conditions for glass particle emission, EC vaped aerosols were collected at three distinctive puffing intervals: (1) 0-10 puffs, (2) 101-110 puffs, and (3) 201-210 puffs (flow rate of 1 L min -1 , 2 s per puff, and 10 puffs per sample). Glass particles were observed as early as after 100 times puffing from certain products, while after 200 from others. Thus, glass particles were generated by increasing the number of puffs and usage of the EC cartomizer. The analysis of glass particles collected onto polycarbonate filters by scanning electron microscopy (SEM)/energy dispersive X-ray spectroscopy (EDS) confirmed the presence of glass particles in samples collected after puffing 100-200 times. The study demonstrated that the possibility of glass particle emissions from the EC device increased considerably with the increasing number of total puffs. Copyright © 2018 Elsevier Inc. All rights reserved.

A reassessment study of multi-material-shell gas puff z-pinches as a pulsed neutron source on the sandia ZR

NASA Astrophysics Data System (ADS)

Chong, Y. K.; Velikovich, A. L.; Thornhil, J. W.; Giuliani, J. L.; Knapp, P.; Jennings, C.

2013-10-01

Over the last few years, numerous 1D and 2D MHD simulation studies of deuterium (D) based double-shell gas-puff Z-pinch implosions driven by the Sandia ZR accelerator have been carried out to assess the Z-pinch as a pulsed thermal fusion neutron source. In these studies, an ad-hoc time-dependent shunt impedance model was used within the external driving circuit model in order to account for the unresolved current loss in the MITL and the load. In this study, we incorporate an improved ZR circuit model recently formulated based on the recent Sandia argon gas-puff experiment circuit data into the multi-material version of the Mach +DDTCRE RMHD code. We reinvestigate the effects of multidimensional structure and nonuniform gradients as well as the outer- and inner-shell material interaction on the implosion physics and dynamics of both D-on-D and argon-on-D Z-pinch loads using the model. Then, we characterize the neutron production performance of the Z-pinch loads as a function of total mass, mass ratio and/or radius toward their optimization as a pulsed thernonuclear neutron source. Work supported by DOE/NNSA. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. DOE's NNSA under contract DE-AC04-94AL85000.

Control of IP3-mediated Ca2+ puffs in Xenopus laevis oocytes by the Ca2+-binding protein parvalbumin

PubMed Central

John, Linu M; Mosquera-Caro, Monica; Camacho, Patricia; Lechleiter, James D

2001-01-01

Elementary events of Ca2+ release (Ca2+ puffs) can be elicited from discrete clusters of inositol 1,4,5 trisphosphate receptors (IP3Rs) at low concentrations of IP3. Ca2+ puffs have rarely been observed unless elicited by either hormone treatment or introduction of IP3 into the cell. However, cells appear to have sufficient concentrations of IP3 (0.1-3.0 μM) to induce Ca2+ release under resting conditions. Here, we investigated Ca2+ puff activity in non-stimulated Xenopus oocytes using confocal microscopy. The fluorescent Ca2+ dye indicators Calcium Green 1 and Oregon Green 488 BAPTA-2 were injected into oocytes to monitor basal Ca2+ activity. In this preparation, injection or overexpression of parvalbumin, an EF-hand Ca2+-binding protein (CaBP), induced Ca2+ puffs in resting Xenopus oocytes. This activity was inhibited by heparin, an IP3R channel blocker, and by mutation of the Ca2+-binding sites in parvalbumin. Ca2+ puff activity was also evoked by injection of low concentrations of the Ca2+ chelator EGTA, but not by calbindin D28k, another member of the EF-hand CaBP superfamily. BAPTA and the Ca2+ indicator dye Oregon Green 488 BAPTA-1 evoked Ca2+ puff activity, while the dextran conjugate of Oregon Green 488 BAPTA-1 did not. These data indicate that a Ca2+ buffer must be mobile in order to increase Ca2+ puff activity. Together, the data indicate that some IP3Rs spontaneously release Ca2+ under resting concentrations of IP3. These elementary Ca2+ events appear to be below the level of detection of current imaging techniques. We suggest that parvalbumin evokes Ca2+ puffs by coordinating the activity of elementary IP3R channel openings. We conclude that Ca2+ release can be evoked not only by hormone-induced increases in IP3, but also by expression of mobile cytosolic CaBPs under resting concentrations of IP3. PMID:11507154

International Space Station (ISS)

NASA Image and Video Library

2003-01-16

In this International Space Station (ISS) onboard photo, Expedition Six Science Officer Donald R. Pettit works to set up the Pulmonary Function in Flight (PuFF) experiment hardware in the Destiny Laboratory. Expedition Six is the fourth and final crew to perform the PuFF experiment. The PuFF experiment was developed to better understand what effects long term exposure to microgravity may have on the lungs. The focus is on measuring changes in the everness of gas exchange in the lungs, and on detecting changes in respiratory muscle strength. It allows astronauts to measure blood flow through the lungs, the ability of the lung to take up oxygen, and lung volumes. Each PuFF session includes five lung function tests, which involve breathing only cabin air. For each planned extravehicular (EVA) activity, a crew member performs a PuFF test within one week prior to the EVA. Following the EVA, those crew members perform another test to document the effect of exposure of the lungs to the low-pressure environment of the space suits. This experiment utilizes the Gas Analyzer System for Metabolic Analysis Physiology, or GASMAP, located in the Human Research Facility (HRF), along with a variety of other Puff equipment including a manual breathing valve, flow meter, pressure-flow module, pressure and volume calibration syringes, and disposable mouth pieces.

Plasma Radiation Source on the Basis of the Gas Puff with Outer Plasma Shell in the Circuit of a Mega-Ampere Load Current Doubler

NASA Astrophysics Data System (ADS)

Kokshenev, V. A.; Labetsky, A. Yu.; Shishlov, A. V.; Kurmaev, N. E.; Fursov, F. I.; Cherdizov, R. K.

2017-12-01

Characteristics of Z-pinch plasma radiation in the form of a double shell neon gas puff with outer plasma shell are investigated in the microsecond implosion mode. Experiments are performed using a GIT-12 mega-joule generator with load current doubler having a ferromagnetic core at implosion currents up to 5 MA. Conditions for matching of the nonlinear load with the mega-ampere current multiplier circuit are determined. The load parameters (plasma shell characteristics and mass and geometry of gas puff shells) are optimized on the energy supplied to the gas puff and n energy characteristics of radiation. It is established that the best modes of K-shell radiation in neon are realized for such radial distribution of the gas-puff material at which the compression velocity of the shell is close to a constant and amounts to 27-30 cm/μs. In these modes, up to 40% of energy supplied to the gas puff is converted into K-shell radiation. The reasons limiting the efficiency of the radiation source with increasing implosion current are analyzed. A modernized version of the energy supply from the current doubler to the Z-pinch is proposed.

Nicotine Delivery and Vaping Behavior During ad Libitum E-cigarette Access.

PubMed

St Helen, Gideon; Ross, Kathryn C; Dempsey, Delia A; Havel, Christopher M; Jacob, Peyton; Benowitz, Neal L

2016-10-01

To characterize vaping behavior and nicotine intake during ad libitum e-cigarette access. Thirteen adult e-cigarette users had 90 minutes of videotaped ad libitum access to their usual e-cigarette. Plasma nicotine was measured before and every 15 minutes after the first puff; subjective effects were measured before and after the session. Average puff duration and interpuff interval were 3.5±1.4 seconds (±SD) and 118±141 seconds, respectively. 12% of puffs were unclustered puffs while 43%, 28%, and 17% were clustered in groups of 2-5, 6-10, and >10 puffs, respectively. On average, 4.0±3.3 mg of nicotine was inhaled; the maximum plasma nicotine concentration (C max ) was 12.8±8.5 ng/mL. Among the 8 tank users, number of puffs was positively correlated with amount of nicotine inhaled, C max , and area under the plasma nicotine concentration-time curve (AUC 0 → 90min ) while interpuff interval was negatively correlated with C max and AUC 0 → 90 . Vaping patterns differ from cigarette smoking. Plasma nicotine levels were consistent with intermittent dosing of nicotine from e-cigarettes compared to the more bolus dosing from cigarettes. Differences in delivery patterns and peak levels of nicotine achieved could influence the addictiveness of e-cigarettes compared to conventional cigarettes.

Marijuana and tobacco cigarettes: Estimating their behavioral economic relationship using purchasing tasks.

PubMed

Peters, Erica N; Rosenberry, Zachary R; Schauer, Gillian L; O'Grady, Kevin E; Johnson, Patrick S

2017-06-01

Although marijuana and tobacco are commonly coused, the nature of their relationship has not been fully elucidated. Behavioral economics has characterized the relationship between concurrently available commodities but has not been applied to marijuana and tobacco couse. U.S. adults ≥18 years who coused marijuana and tobacco cigarettes were recruited via Mechanical Turk, a crowdsourcing service by Amazon. Participants (N = 82) completed online purchasing tasks assessing hypothetical marijuana or tobacco cigarette puff consumption across a range of per-puff prices; 2 single-commodity tasks assessed these when only 1 commodity was available, and 2 cross-commodity tasks assessed these in the presence of a concurrently available fixed-price commodity. Purchasing tasks generated measures of demand elasticity, that is, sensitivity of consumption to prices. In single-commodity tasks, consumption of tobacco cigarette puffs (elasticity of demand: α = 0.0075; 95% confidence interval [0.0066, 0.0085], R² = 0.72) and of marijuana puffs (α = .0044; 95% confidence interval [0.0038, 0.0049], R² = 0.71) declined significantly with increases in price per puff. In cross-commodity tasks when both tobacco cigarette puffs and marijuana puffs were available, demand for 1 commodity was independent of price increases in the other commodity (ps > .05). Results revealed that, in this small sample, marijuana and tobacco cigarettes did not substitute for each other and did not complement each other; instead, they were independent of each other. These preliminary results can inform future studies assessing the economic relationship between tobacco and marijuana in the quickly changing policy climate in the United States. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Impact of e-liquid flavors on e-cigarette vaping behavior.

PubMed

St Helen, Gideon; Shahid, Marian; Chu, Sherman; Benowitz, Neal L

2018-05-31

The primary objective of this pilot study was to describe the impact of e-cigarette liquid flavors on experienced e-cigarette users' vaping behavior. 11 males and 3 females participated in a 3-day inpatient crossover study using e-cigarettes with strawberry, tobacco, and their usual brand e-liquid. Nicotine levels were nominally 18 mg/mL in the strawberry and tobacco e-liquids and ranged between 3-18 mg/mL in the usual brands. On each day, participants had access to the study e-cigarette (KangerTech mini ProTank 3, 1.5 Ohms, 3.7 V) and the assigned e-liquid during a 90-minute videotaped ad libitum session. Average puff duration was significantly longer when using the strawberry e-liquid (3.2 ± 1.3 s, mean ± SD) compared to the tobacco e-liquid (2.8 ± 1.1 s) but the average number of puffs was not significantly different (strawberry, 73 ± 35; tobacco, 69 ± 46). Compared to the strawberry- and tobacco-flavored e-liquids, average puff duration was significantly longer (4.3 ± 1.6 s) and the average number of puffs was significantly higher (106 ± 67 puffs) when participants used their usual brand of e-liquid. Participants generally puffed more frequently in small groups of puffs (1-5 puffs) with the strawberry compared to the tobacco e-liquid and more frequently in larger groups (>10 puffs) with their usual brand. The strength of the relationship between vaping topography and nicotine intake and exposure were not consistent across e-liquids. Vaping behavior changes across e-liquids and influences nicotine intake. Research is needed to understand the mechanisms that underlie these behavioral changes, including e-liquid pH and related sensory effects, subjective liking, and nicotine effects. Copyright © 2018. Published by Elsevier B.V.

Development of a plume-in-grid model for industrial point and volume sources: application to power plant and refinery sources in the Paris region

NASA Astrophysics Data System (ADS)

Kim, Y.; Seigneur, C.; Duclaux, O.

2014-04-01

Plume-in-grid (PinG) models incorporating a host Eulerian model and a subgrid-scale model (usually a Gaussian plume or puff model) have been used for the simulations of stack emissions (e.g., fossil fuel-fired power plants and cement plants) for gaseous and particulate species such as nitrogen oxides (NOx), sulfur dioxide (SO2), particulate matter (PM) and mercury (Hg). Here, we describe the extension of a PinG model to study the impact of an oil refinery where volatile organic compound (VOC) emissions can be important. The model is based on a reactive PinG model for ozone (O3), which incorporates a three-dimensional (3-D) Eulerian model and a Gaussian puff model. The model is extended to treat PM, with treatments of aerosol chemistry, particle size distribution, and the formation of secondary aerosols, which are consistent in both the 3-D Eulerian host model and the Gaussian puff model. Furthermore, the PinG model is extended to include the treatment of volume sources to simulate fugitive VOC emissions. The new PinG model is evaluated over Greater Paris during July 2009. Model performance is satisfactory for O3, PM2.5 and most PM2.5 components. Two industrial sources, a coal-fired power plant and an oil refinery, are simulated with the PinG model. The characteristics of the sources (stack height and diameter, exhaust temperature and velocity) govern the surface concentrations of primary pollutants (NOx, SO2 and VOC). O3 concentrations are impacted differently near the power plant than near the refinery, because of the presence of VOC emissions at the latter. The formation of sulfate is influenced by both the dispersion of SO2 and the oxidant concentration; however, the former tends to dominate in the simulations presented here. The impact of PinG modeling on the formation of secondary organic aerosol (SOA) is small and results mostly from the effect of different oxidant concentrations on biogenic SOA formation. The investigation of the criteria for injecting plumes into the host model (fixed travel time and/or puff size) shows that a size-based criterion is recommended to treat the formation of secondary aerosols (sulfate, nitrate, and ammonium), in particular, farther downwind of the sources (beyond about 15 km). The impacts of PinG modeling are less significant in a simulation with a coarse grid size (10 km) than with a fine grid size (2 km), because the concentrations of the species emitted from the PinG sources are relatively less important compared to background concentrations when injected into the host model with a coarser grid size.

Development of a plume-in-grid model for industrial point and volume sources: application to power plant and refinery sources in the Paris region

NASA Astrophysics Data System (ADS)

Kim, Y.; Seigneur, C.; Duclaux, O.

2013-11-01

Plume-in-grid (PinG) models incorporating a host Eulerian model and a subgrid-scale model (usually a Gaussian plume or puff model) have been used for the simulations of stack emissions (e.g., fossil fuel-fired power plants and cement plants) for gaseous and particulate species such as nitrogen oxides (NOx), sulfur dioxide (SO2), particulate matter (PM) and mercury (Hg). Here, we describe the extension of a PinG model to study the impact of an oil refinery where volatile organic compound (VOC) emissions can be important. The model is based on a reactive PinG model for ozone (O3), which incorporates a three-dimensional (3-D) Eulerian model and a Gaussian puff model. The model is extended to treat PM, with treatments of aerosol chemistry, particle size distribution, and the formation of secondary aerosols, which are consistent in both the 3-D Eulerian host model and the Gaussian puff model. Furthermore, the PinG model is extended to include the treatment of volume sources to simulate fugitive VOC emissions. The new PinG model is evaluated over Greater Paris during July 2009. Model performance is satisfactory for O3, PM2.5 and most PM2.5 components. Two industrial sources, a coal-fired power plant and an oil refinery, are simulated with the PinG model. The characteristics of the sources (stack height and diameter, exhaust temperature and velocity) govern the surface concentrations of primary pollutants (NOx, SO2 and VOC). O3 concentrations are impacted differently near the power plant than near the refinery, because of the presence of VOC emissions at the latter. The formation of sulfate is influenced by both the dispersion of SO2 and the oxidant concentration; however, the former tends to dominate in the simulations presented here. The impact of PinG modeling on the formation of secondary organic aerosols (SOA) is small and results mostly from the effect of different oxidant concentrations on biogenic SOA formation. The investigation of the criteria for injecting plumes into the host model (fixed travel time and/or puff size) shows that a size-based criterion is recommended to treat the formation of secondary aerosols (sulfate, nitrate, and ammonium), in particular, farther downwind of the sources (from about 15 km). The impacts of the PinG modeling are less significant in a simulation with a coarse grid size (10 km) than with a fine grid size (2 km), because the concentrations of the species emitted from the PinG sources are relatively less important compared to background concentrations when injected into the host model.

Predicting air quality near roadways through the application of a Gaussian Puff Model to moving sources

DOT National Transportation Integrated Search

2000-06-19

The Environmental Protection Agency (EPA) currently recommends the use of CALINE3 or CAL3QHC for modeling the dispersion of carbon monoxide (CO) near roadways. These models treat vehicles as part of a line source such that the emissions are homogeneo...

Debris-free soft x-ray source with gas-puff target

NASA Astrophysics Data System (ADS)

Ni, Qiliang; Chen, Bo; Gong, Yan; Cao, Jianlin; Lin, Jingquan; Lee, Hongyan

2001-12-01

We have been developing a debris-free laser plasma light source with a gas-puff target system whose nozzle is driven by a piezoelectric crystal membrane. The gas-puff target system can utilize gases such as CO2, O2 or some gas mixture according to different experiments. Therefore, in comparison with soft X-ray source using a metal target, after continuously several-hour laser interaction with gas from the gas-puff target system, no evidences show that the light source can produce debris. The debris-free soft X-ray source is prepared for soft X-ray projection lithography research at State Key Laboratory of Applied Optics. Strong emission from CO2, O2 and Kr plasma is observed.

The impact of flavoring on the rewarding and reinforcing value of e-cigarettes with nicotine among young adult smokers.

PubMed

Audrain-McGovern, Janet; Strasser, Andrew A; Wileyto, E Paul

2016-09-01

Flavored e-cigarette use has risen rapidly, especially among young adults who also smoke cigarettes. We sought to determine whether flavoring enhances the subjective rewarding value, relative reinforcing value, and absolute reinforcing value of an e-cigarette with nicotine compared to an unflavored e-cigarette with nicotine. Using a within-subjects design, young adult smokers (n=32) participated in three human laboratory sessions. Session 1 evaluated the rewarding value of flavoring by having participants rate unflavored and flavored e-cigarettes with nicotine. Session 2 assessed the relative reinforcing value of a flavored vs unflavored e-cigarette via a choice task that evaluated the willingness to "work" to hit targets on a computer screen to earn flavored or unflavored e-cigarette puffs. Session 3 measured the absolute reinforcing value of flavored versus unflavored e-cigarettes via a 90-min ad-libitum vaping session where puffs from each e-cigarette were counted. Subjective reward value was higher for the flavored versus the unflavored e-cigarette (β=0.83, CI 0.35-1.32, p=0.001). Participants worked harder for flavored e-cigarette puffs versus unflavored e-cigarette puffs (breakpoint=5.7; 597 responses versus 127 responses; β=460.733, CI 246.58-674.88, p<0.0001). Participants took twice as many flavored puffs than unflavored e-cigarette puffs (40 vs 23 puffs; IRR=2.028, CI 1.183-3.475, p=0.01). Flavoring enhances the rewarding and reinforcing value of e-cigarettes with nicotine, and thus their abuse liability in young adult smokers. Further research is necessary to determine whether the use of flavoring in e-cigarettes impacts cigarette smoking behavior among young adults. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

The impact of flavoring on the rewarding and reinforcing value of e-cigarettes with nicotine among young adult smokers

PubMed Central

Audrain-McGovern, Janet; Strasser, Andrew A.; Wileyto, E. Paul

2016-01-01

Objective Flavored e-cigarette use has risen rapidly, especially among young adults who also smoke cigarettes. We sought to determine whether flavoring enhances the subjective rewarding value, relative reinforcing value, and absolute reinforcing value of an e-cigarette with nicotine compared to an unflavored e-cigarette with nicotine. Methods Using a within-subjects design, young adult smokers (n=32) participated in three human laboratory sessions. Session 1 evaluated the rewarding value of flavoring by having participants rate unflavored and flavored e-cigarettes with nicotine. Session 2 assessed the relative reinforcing value of a flavored vs unflavored e-cigarette via a choice task that evaluated the willingness to “work” to hit targets on a computer screen to earn flavored or unflavored e-cigarette puffs. Session 3 measured the absolute reinforcing value of flavored versus unflavored e-cigarettes via a 90-minute ad-libitum vaping session where puffs from each e-cigarette were counted. Results Subjective reward value was higher for the flavored versus the unflavored e-cigarette (β=.83, CI 0.35 to 1.32, p=0.001). Participants worked harder for flavored e-cigarette puffs versus unflavored e-cigarette puffs (breakpoint = 5.7; 597 responses versus 127 responses; β=460.733, CI 246.58 to 674.88, p <0.0001). Participants took twice as many flavored puffs than unflavored e-cigarette puffs (40 vs 23 puffs; IRR=2.028, CI 1.183 to 3.475, p=0.01). Conclusions Flavoring enhances the rewarding and reinforcing value of e-cigarettes with nicotine, and thus their abuse liability in young adult smokers. Further research is necessary to determine whether the use of flavoring in e-cigarettes impacts cigarette smoking behavior among young adults. PMID:27426010

Influence of Smoking Puff Parameters and Tobacco Varieties on Free Radicals Yields in Cigarette Mainstream Smoke.

PubMed

Goel, Reema; Bitzer, Zachary T; Reilly, Samantha M; Foulds, Jonathan; Muscat, Joshua; Elias, Ryan J; Richie, John P

2018-05-07

Cigarette smoke is a major exogenous source of free radicals, and the resulting oxidative stress is one of the major causes of smoking-caused diseases. Yet, many of the factors that impact free radical delivery from cigarettes remain unclear. In this study, we machine-smoked cigarettes and measured the levels of gas- and particulate-phase radicals by electron paramagnetic resonance (EPR) spectroscopy using standardized smoking regimens (International Organization of Standardization (ISO) and Canadian Intense (CI)), puffing parameters, and tobacco blends. Radical delivery per cigarette was significantly greater in both gas (4-fold) and particulate (6-fold) phases when cigarettes were smoked under the CI protocol compared to the ISO protocol. Total puff volume per cigarette was the major factor with radical production being proportional to total volume, regardless of whether volume differences were achieved by changes in individual puff volume or puff frequency. Changing puff shape (bell vs sharp vs square) or puff duration (1-5 s), without changing volume, had no effect on radical yields. Tobacco variety did have a significant impact on free radical production, with gas-phase radicals highest in reconstituted > burley > oriental > bright tobacco and particulate-phase radicals highest in burley > bright > oriental > reconstituted tobacco. Our findings show that modifiable cigarette design features and measurable user smoking behaviors are key factors determining free radical exposure in smokers.

Nicotine Delivery and Vaping Behavior During ad Libitum E-cigarette Access

PubMed Central

St.Helen, Gideon; Ross, Kathryn C.; Dempsey, Delia A.; Havel, Christopher M.; Jacob, Peyton; Benowitz, Neal L.

2017-01-01

Objective To characterize vaping behavior and nicotine intake during ad libitum e-cigarette access. Methods Thirteen adult e-cigarette users had 90 minutes of videotaped ad libitum access to their usual e-cigarette. Plasma nicotine was measured before and every 15 minutes after the first puff; subjective effects were measured before and after the session. Results Average puff duration and interpuff interval were 3.5±1.4 seconds (±SD) and 118±141 seconds, respectively. 12% of puffs were unclustered puffs while 43%, 28%, and 17% were clustered in groups of 2–5, 6–10, and >10 puffs, respectively. On average, 4.0±3.3 mg of nicotine was inhaled; the maximum plasma nicotine concentration (Cmax) was 12.8±8.5 ng/mL. Among the 8 tank users, number of puffs was positively correlated with amount of nicotine inhaled, Cmax, and area under the plasma nicotine concentration-time curve (AUC0→90min) while interpuff interval was negatively correlated with Cmax and AUC0→90. Conclusion Vaping patterns differ from cigarette smoking. Plasma nicotine levels were consistent with intermittent dosing of nicotine from e-cigarettes compared to the more bolus dosing from cigarettes. Differences in delivery patterns and peak levels of nicotine achieved could influence the addictiveness of e-cigarettes compared to conventional cigarettes. PMID:28393086

Impact of low-trans fat compositions on the quality of conventional and fat-reduced puff pastry.

PubMed

Silow, Christoph; Zannini, Emanuele; Arendt, Elke K

2016-04-01

Four vegetable fat blends (FBs) with low trans-fatty acid (TFA ≤ 0.6 %) content with various ratios of palm stearin (PS) and rapeseed oil (RO) were characterised and examined for their application in puff pastry production. The amount of PS decreased from FB1 to FB4 and simultaneously the RO content increased. A range of analytical methods were used to characterise the FBs, including solid fat content (SFC), differential scanning calorimetry (DSC), cone penetrometry and rheological measurements. The internal and external structural quality parameters of baked puff pastry were investigated using texture analyser equipped with an Extended Craft Knife (ECK), VolScan and C-Cell image system. Puff pastry containing FB1 and FB2 achieved excellent baking results for full fat and fat-reduced puff pastry; hence these FBs contained adequate shortening properties. A fat reduction by 40 % using FB2 and a reduction of saturated fatty acids (SAFA) by 49 %, compared to the control, did not lead to adverse effects in lift and specific volume. The higher amount of RO and the lower SAFA content compared to FB1 coupled with the satisfying baking results makes FB2 the fat of choice in this study. FB3 and FB4 were found to be unsuitable for puff pastry production because of their melting behaviour.

A New Variety of CMEs: Streamer Puffs from Compact Ejective Flares

NASA Technical Reports Server (NTRS)

Sterling, Alphonse C.; Bemporad, A.; Moore, R. L.; Poletto, G.

2005-01-01

We present SOHO EIT, UVCS and LASCO observations of recurrent (6 --- 8 events per day) narrow (angular widths of about 3 --- 10 degrees) Coronal Mass Ejections (CMEs) which occurred over 2002 November 26--29. The active region where the ejections originate is near the base of a coronal streamer that appears to be unperturbed by the events and keeps stable in time; hence we interpret the observed events as a new class of recursive narrow CMEs that we call "streamer puffs." EIT 304 angstrom (He II) images indicate that the puffs result from compact ejective flares embedded in the streamer, with the ejections from the flares having velocities 100 --- 200 kilometers per second. Most ejections are closely correlated with coronal "jets" seen at 1.7 solar radii in the UVCS data, and a subset of these ejections and jets correspond to streamer puffs observed in LASCO coronagraph images. There are, however, more compact flares and jets than streamer puffs during the observation period, indicating that only a subset of the flare-associated ejections are energetic enough to escape into the heliosphere.

Radial and Azimuthal Velocity Profiles in Gas-Puff Z-Pinches

NASA Astrophysics Data System (ADS)

Rocco, Sophia; Engelbrecht, Joseph; Banasek, Jacob; de Grouchy, Philip; Qi, Niansheng; Hammer, David

2016-10-01

The dynamics of neon, argon, and krypton (either singly or in combination) gas puff z-pinch plasmas are studied on Cornell's 1MA, 100-200ns rise-time COBRA pulsed power generator. The triple-nozzle gas puff valve, consisting of two annular gas puffs and a central jet, allows radial tailoring of the gas puff mass-density profile and the use of 1, 2 or 3 different gases at different pressures. Interferometry supplies information on sheath thickness and electron density, variously filtered PCDs and silicon diodes measure hard and soft x-ray production, and multi frame visible and extreme UV imaging systems allow tracking of the morphology of the plasma. A 527nm, 10J Thomson scattering diagnostic system is used to determine radial and azimuthal velocities. Implosion velocities of 170km/s (Kr) and 300km/s (Ne/Ar) are observed. We are investigating the correlations between instability growth, plasma density profile, velocity partitioning as a function of radius, and radiation production. Research supported by the NNSA Stewardship Sciences Academic Programs under DOE Cooperative Agreement No. DE-NA0001836.

Impact assessment of PM10 cement plants emissions on urban air quality using the SCIPUFF dispersion model.

PubMed

Leone, Vincenzo; Cervone, Guido; Iovino, Pasquale

2016-09-01

The Second-order Closure Integrated Puff (SCIPUFF) model was used to study the impact on urban air quality caused by two cement plants emissions located near the city of Caserta, Italy, during the entire year of 2015. The simulated and observed PM10 concentrations were compared using three monitoring stations located in urban and sub-urban area of Caserta city. Both simulated and observed concentrations are shown to be highest in winter, lower in autumn and spring and lowest in summer. Model results generally follow the pattern of the observed concentrations but have a systematic under-prediction of the concentration values. Measures of the bias, NMSE and RMSE indicate a good correlation between observed and estimated values. The SCIPUFF model data analysis suggest that the cement plants are major sources for the measured PM10 values and are responsible for the deterioration of the urban air quality in the city of Caserta.

DEVELOPMENT OF MESOSCALE AIR QUALITY SIMULATION MODELS. VOLUME 1. COMPARATIVE SENSITIVITY STUDIES OF PUFF, PLUME, AND GRID MODELS FOR LONG DISTANCE DISPERSION

EPA Science Inventory

This report provides detailed comparisons and sensitivity analyses of three candidate models, MESOPLUME, MESOPUFF, and MESOGRID. This was not a validation study; there was no suitable regional air quality data base for the Four Corners area. Rather, the models have been evaluated...

The modulatory effects of rostral ventromedial medulla on air-puff evoked microarousals in rats

PubMed Central

Foo, H.; Crabtree, Katherine; Mason, Peggy

2010-01-01

This study tested whether the duration of microarousals from sleep evoked by innocuous air-puff is affected by intra-RVM administration of neurotensin and bicuculline, pharmacological manipulations that affect ON and OFF cell activity. Air-puff evoked microarousal duration was unaffected by 0.05 ng neurotensin, but decreased by 502 ng neurotensin, and 5 and 50 ng bicuculline. These results suggest a putative role for OFF cells in protecting sleep from interruption by non-noxious stimuli. PMID:20621127

Intra-puff CO and CO 2 measurements of cigarettes with iron oxide cigarette paper using quantum cascade laser spectroscopy

NASA Astrophysics Data System (ADS)

Crawford, Danielle R.; Parrish, Milton E.; Gee, Diane L.; Harward, Charles N.

2007-05-01

The objective of this research was to apply Fourier transform infrared spectroscopy (FTIR) and tunable infrared laser differential absorption spectroscopy (TILDAS) for measuring selected gaseous constituents in mainstream (MS) and sidestream (SS) smoke for experimental cigarettes designed to reduce MS CO using iron oxide cigarette papers. These two complimentary analytical techniques are well suited for providing per puff smoke deliveries and intra-puff evolution profiles in cigarette smoke respectively. The quad quantum cascade (QC) laser high resolution infrared spectroscopy system has the necessary temporal and spectral resolution and whole smoke analysis capabilities to provide detailed information for CO and CO 2 as they are being formed in both MS and SS smoke. The QC laser system has an optimal data rate of 20 Hz and a unique puffing system, with a square wave shaped puff, that allows whole smoke to enter an 18 m, 0.3 L multi-pass gas cell in real time (0.1 s cell response time) requiring no syringe or Cambridge filter pad. Another similar multi-pass gas cell with a 36 m pathlength simultaneously monitors the sidestream cigarette smoke. The smoke from experimental cigarettes manufactured with two types of iron oxide papers were compared to the smoke from cigarettes manufactured similarly without iron oxide in the paper using both instrument systems. The delivery per puff determined by the QC laser method agreed with FTIR results. MS CO intra-puff evolution profiles for iron oxide prototype cigarettes demonstrated CO reduction when compared to cigarettes without iron oxide paper. Additionally, both CO and CO 2 intra-puff evolution profiles of the cigarettes with iron oxide paper showed a significant reduction at the initial portion of the 2 s puff not observed in the non-iron oxide prototype cigarettes. This effect also was observed for ammonia and ethylene, suggesting that physical parameters such as paper porosity and burn rate are important. The SS CO and CO 2 deliveries for the experimental cigarettes evaluated remained unaffected. The iron oxide paper technology remains under development and continues to be evaluated.

Intra-puff CO and CO2 measurements of cigarettes with iron oxide cigarette paper using quantum cascade laser spectroscopy.

PubMed

Crawford, Danielle R; Parrish, Milton E; Gee, Diane L; Harward, Charles N

2007-05-01

The objective of this research was to apply Fourier transform infrared spectroscopy (FTIR) and tunable infrared laser differential absorption spectroscopy (TILDAS) for measuring selected gaseous constituents in mainstream (MS) and sidestream (SS) smoke for experimental cigarettes designed to reduce MS CO using iron oxide cigarette papers. These two complimentary analytical techniques are well suited for providing per puff smoke deliveries and intra-puff evolution profiles in cigarette smoke respectively. The quad quantum cascade (QC) laser high resolution infrared spectroscopy system has the necessary temporal and spectral resolution and whole smoke analysis capabilities to provide detailed information for CO and CO(2) as they are being formed in both MS and SS smoke. The QC laser system has an optimal data rate of 20 Hz and a unique puffing system, with a square wave shaped puff, that allows whole smoke to enter an 18 m, 0.3 L multi-pass gas cell in real time (0.1s cell response time) requiring no syringe or Cambridge filter pad. Another similar multi-pass gas cell with a 36 m pathlength simultaneously monitors the sidestream cigarette smoke. The smoke from experimental cigarettes manufactured with two types of iron oxide papers were compared to the smoke from cigarettes manufactured similarly without iron oxide in the paper using both instrument systems. The delivery per puff determined by the QC laser method agreed with FTIR results. MS CO intra-puff evolution profiles for iron oxide prototype cigarettes demonstrated CO reduction when compared to cigarettes without iron oxide paper. Additionally, both CO and CO(2) intra-puff evolution profiles of the cigarettes with iron oxide paper showed a significant reduction at the initial portion of the 2 s puff not observed in the non-iron oxide prototype cigarettes. This effect also was observed for ammonia and ethylene, suggesting that physical parameters such as paper porosity and burn rate are important. The SS CO and CO(2) deliveries for the experimental cigarettes evaluated remained unaffected. The iron oxide paper technology remains under development and continues to be evaluated.

EVALUATION AND SENSITIVITY ANALYSES RESULTS OF THE MESOPUFF II MODEL WITH CAPTEX MEASUREMENTS

EPA Science Inventory

The MESOPUFF II regional Lagrangian puff model has been evaluated and tested against measurements from the Cross-Appalachian Tracer Experiment (CAPTEX) data base in an effort to assess its abilIty to simulate the transport and dispersion of a nonreactive, nondepositing tracer plu...

Smoking Topography in Korean American and White Men: Preliminary Findings

PubMed Central

Chung, Sangkeun; Kim, Sun S; Kini, Nisha; Fang, Hua J; Kalman, David; Ziedonis, Douglas M.

2013-01-01

Introduction This is the first study of Korean Americans’ smoking behavior using a topography device. Korean American men smoke at higher rates than the general U.S. population. Methods Korean American and White men were compared based on standard tobacco assessment and smoking topography measures. They smoked their preferred brand of cigarettes ad libitum with a portable smoking topography device for 24 hours. Results Compared to White men (N = 26), Korean American men (N = 27) were more likely to smoke low nicotine-yield cigarettes (p < 0.001) and have lower Fagerstrom nicotine dependence scores (p = 0.04). Koreans smoked fewer cigarettes with the device (p = 0.01) than Whites. Controlling for the number of cigarettes smoked, Koreans smoked with higher average puff flows (p = 0.05), greater peak puff flows (p = 0.02), and shorter interpuff intervals (p < 0.001) than Whites. Puff counts, puff volumes, and puff durations did not differ between the two groups. Conclusions This study offers preliminary insight into unique smoking patterns among Korean American men who are likely to smoke low nicotine-yield cigarettes. We found that Korean American men compensated their lower number and low nicotine-yield cigarettes by smoking more frequently with greater puff flows than White men, which may suggest exposures to similar amounts of nicotine and harmful tobacco toxins by both groups. Clinicians will need to consider in identifying and treating smokers in a mutually aggressive manner, irrespective of cigarette type and number of cigarette smoked per day. PMID:24068611

Marijuana smoking: effects of varying puff volume and breathhold duration.

PubMed

Azorlosa, J L; Greenwald, M K; Stitzer, M L

1995-02-01

Two studies were conducted to quantify biological and behavioral effects resulting from exposure to controlled doses of marijuana smoke. In one study, puff volume (30, 60 and 90 ml) and in a second study, breathhold duration (0, 10 and 20 sec) were systematically varied while holding constant other smoking topography parameters (number of puffs = 10, interpuff interval = 60 sec and inhalation volume = 25% of vital capacity). Each study also varied levels of delta 9-tetrahydro-cannabinol marijuana cigarette content (1.75% and 3.55%). Regular marijuana users served as subjects (n = 7 in each experiment). Subjects smoked 10 puffs in each of six sessions; a seventh, nonsmoking session (all measures recorded at the same times as in active smoking sessions) served as a control. Variations in puff volume produced significant dose-related changes in postsmoking plasma delta 9-tetrahydro-cannabinol levels, carbon monoxide boost and subjective effects (e.g., "high"). In contrast, breathholding for 10 or 20 sec versus 0 sec increased plasma delta 9-tetrahydro-cannabinol levels but not CO boost or subjective effects. Task performance measures were not reliably influenced by marijuana smoke exposure within the dosing ranges examined. These findings confirm the utility of the controlled smoking technology, support the notion that cumulative puff volume systematically influences biological exposure and subjective effects, but cast doubt on the common belief that prolonged breathholding of marijuana smoke enhances classical subjective effects associated with its reinforcing value in humans.

Plasma-puff initiation of high Coulomb transfer switches

NASA Technical Reports Server (NTRS)

Han, Kwang S.; Venable, Demetrius D.; Lee, Ja H.; Choi, Eun H.; Kim, Y. K.; Kim, J. H.; Nguyen, D. X.

1993-01-01

The plasma-puff triggering mechanism based on a hypocycloidal pinch geometry was investigated to determine the optimal operating conditions for an azimuthally uniform surface flashover which initiates plasma-puff under wide ranges of fill gas pressures of Ar, He and N2. The optimal fill gas pressures for the azimuthally uniform plasma-puff were about 120 mTorr less than P(sub opt) less than 450 Torr for He and N2. For Argon 20 mTorr is less than P(sub opt) is less than 5 Torr. The inverse pinch switch was triggered with the plasma-puff and the switching capability under various electrical parameters and working gas pressures of Ar, He and N2 was determined. It was also shown that the azimuthally uniform switching discharges were dependent on the type of fill gas and its fill pressure. A new concept of plasma-focus driven plasma-puff was also discussed in comparison with hypocycloidal pinch plasma-puff triggering. The main discharge of the inverse pinch switch with the plasma-focus driven plasma-puff trigger is found to be more azimuthally uniform than that with the hypocycloidal pinch plasma-puff trigger in a gas pressure region between 80 mTorr and 1 Torr. In order to assess the effects of plasma current density on material erosion of electrodes, emissions from both an inverse-pinch plasma switch (INPIStron) and from a spark gap switch under test were studied with an optical multichannel analyzer (OMA). The color temperature of the argon plasma was approximately 4,000 K which corresponded with the peak continuum emission near 750 nm. There are the strong line emissions of argon in the 650 - 800 nm range and a lack of line emissions of copper and other solid material used in the switch. This indicates that the plasma current density during closing is low and the hot spot or hot filament in the switch is negligible. This result also indicates considerable reduction of line emission with the INPIStron switch over that of a spark-gap switch. However, a strong carbon line emission exists due to vaporization of the plastic insulator used. In order to reduce the vaporization of the insulator, the plexiglass insulating material of INPIStron was replaced with Z-9 material. A comparative study of the INPIStron and a spark gap also reveals that the INPIStron, with a low impedance of Z = 9 ohms, can transfer a high voltage pulse with a superior pulse-shape fidelity over that of a spark gap with Z = 100 ohms.

Plasma-puff initiation of high Coulomb transfer switches

NASA Technical Reports Server (NTRS)

Venable, D. D.; Han, K. S.

1993-01-01

The plasma-puff triggering mechanism based on a hypocycloidal pinch geometry was investigated to determine the optimal operating conditions for an azimuthally uniform surface flashover which initiates plasma-puff under wide ranges of fill gas pressures of Ar, He and N2. The optimal fill gas pressures for the azimuthally uniform plasma-puff were about 120 mTorr less than P(opt) less than 450 Torr for He and N2. For Argon 120 mTorr less than P(opt) less than 5 Torr for argon. The inverse pinch switch was triggered with the plasma-puff and the switching capability under various electrical parameters and working gas pressures of Ar, He and N2 was determined. It was also shown that the azimuthally uniform switching discharges were dependent on the type of fill gas and its fill pressure. A new concept of plasma-focus driven plasma-puff was also discussed in comparison with hypocycloidal pinch plasma-puff triggering. The main discharge of the inverse pinch switch with the plasma-focus driven plasma-puff trigger is found to be more azimuthally uniform than that with the hypocycloidal pinch plasma-puff trigger in a gas pressure region between 80 mTorr and 1 Torr. In order to assess the effects of plasma current density on material erosion of electrodes, emissions from both an inverse-pinch plasma switch (INPIStron) and from a spark gap switch under test were studied with an optical multichannel analyzer (OMA). The color temperature of the argon plasma was approximately 4,000 K which corresponded with the peak continuum emission near 750 nm. There are the strong line emissions of argon in the 650 - 800 nm range and a lack of line emissions of copper and other solid material used in the switch. This indicates that the plasma current density during closing is low and the hot spot or hot filament in the switch is negligible. This result also indicates considerable reduction of line emission with the INPIStron switch over that of a spark-gap switch. However, a strong carbon line emission exists due to vaporization of the plastic insulator used. In order to reduce the vaporization of the insulator, the plexiglass insulating material of INPIStron was replaced with Z-9 material. A comparative study of the INPIStron and a spark gap also reveals that the INPIStron, with a low impedance of Z equals 9 ohms, can transfer a high voltage pulse with a superior pulse-shape fidelity over that of a spark gap with Z equals 100 ohms.

Effects of alternative reinforcer and craving on the choice to smoke cigarettes in the laboratory.

PubMed

Bisaga, Adam; Padilla, Margarita; Garawi, Fatima; Sullivan, Maria A; Haney, Margaret

2007-01-01

We examined to what extent craving for cigarettes and the magnitude of an alternative monetary reinforcer were predictors of the choice to smoke in the human laboratory. Twelve non-treatment-seeking nicotine-dependent volunteers participated in a series of outpatient sessions during which they had repeated opportunities to select between three puffs of a cigarette and a variety of monetary alternatives ($0.50-3), responding under a progressive-ratio schedule. Level of cigarette craving was measured at baseline and between each choice opportunity. The probability of choosing a cigarette decreased significantly with the increase in the magnitude of the alternative reinforcer. Baseline level of craving did not significantly alter the probability of choosing a cigarette, but a craving component related to the anticipation of positive effects from smoking, assessed repeatedly between choice opportunities, was predictive of the choice to smoke. These results demonstrate that the cigarette puff self-administration procedure is sensitive to environmental manipulations and cigarette puff choice can be modified by the availability of an alternative reinforcer. This paradigm models the motivational component associated with choice to smoke and could be used to evaluate the effects of pharmacological and behavioral interventions to decrease cigarette smoking.

Probability density function of a puff dispersing from the wall of a turbulent channel

NASA Astrophysics Data System (ADS)

Nguyen, Quoc; Papavassiliou, Dimitrios

2015-11-01

Study of dispersion of passive contaminants in turbulence has proved to be helpful in understanding fundamental heat and mass transfer phenomena. Many simulation and experimental works have been carried out to locate and track motions of scalar markers in a flow. One method is to combine Direct Numerical Simulation (DNS) and Lagrangian Scalar Tracking (LST) to record locations of markers. While this has proved to be useful, high computational cost remains a concern. In this study, we develop a model that could reproduce results obtained by DNS and LST for turbulent flow. Puffs of markers with different Schmidt numbers were released into a flow field at a frictional Reynolds number of 150. The point of release was at the channel wall, so that both diffusion and convection contribute to the puff dispersion pattern, defining different stages of dispersion. Based on outputs from DNS and LST, we seek the most suitable and feasible probability density function (PDF) that represents distribution of markers in the flow field. The PDF would play a significant role in predicting heat and mass transfer in wall turbulence, and would prove to be helpful where DNS and LST are not always available.

Avian maternal response to chick distress

PubMed Central

Edgar, J. L.; Lowe, J. C.; Paul, E. S.; Nicol, C. J.

2011-01-01

The extent to which an animal is affected by the pain or distress of a conspecific will depend on its capacity for empathy. Empathy most probably evolved to facilitate parental care, so the current study assessed whether birds responded to an aversive stimulus directed at their chicks. Domestic hens were exposed to two replicates of the following conditions in a counterbalanced order: control (C; hen and chicks undisturbed), air puff to chicks (APC; air puff directed at chicks at 30 s intervals), air puff to hen (APH; air puff directed at hen at 30 s intervals) and control with noise (CN; noise of air puff at 30 s intervals). During each test, the hens' behaviour and physiology were measured throughout a 10 min pre-treatment and a 10 min treatment period. Hens responded to APH and APC treatments with increased alertness, decreased preening behaviour and a reduction in eye temperature. No such changes occurred during any control period. Increased heart rate and maternal vocalization occurred exclusively during the APC treatment, even though chicks produced few distress vocalizations. The pronounced and specific reaction observed indicates that adult female birds possess at least one of the essential underpinning attributes of empathy. PMID:21389025

Investigating the effect of adding an on-axis jet to Ar gas puff Z pinches on Z.

DOE PAGES

Harvey-Thompson, Adam James; Jennings, Christopher Ashley; Jones, Brent M.; ...

2016-10-20

Double-shell Ar gas puff implosions driven by 16.5±0.5 MA on the Z generator at Sandia National Laboratories are very effective emitters of Ar K-shell radiation (photon energy >3 keV), producing yields of 330 ± 9% kJ (B. Jones et al., Phys. Plasmas, 22, 020706, 2015). In addition, previous simulations and experiments have reported dramatic increases in K-shell yields when adding an on-axis jet to double shell gas puffs for some configurations.

Measurement of acrolein and 1,3-butadiene in a single puff of cigarette smoke using lead-salt tunable diode laser infrared spectroscopy.

PubMed

Thweatt, W Dave; Harward, Charles N; Parrish, Milton E

2007-05-01

Acrolein and 1,3-butadiene in cigarette smoke generally are measured using two separate analytical methods, a carbonyl derivative HPLC method for acrolein and a volatile organic compound (VOC) GC/MS method for 1,3-butadiene. However, a single analytical method having improved sensitivity and real-time per puff measurement will offer more specific information for evaluating experimental carbon filtered cigarettes designed to reduce the smoke deliveries of these constituents. This paper describes an infrared technique using two lead-salt tunable diode lasers (TDLs) operating with liquid nitrogen cooling with emissions at 958.8 cm(-1) and 891.0 cm(-1) respectively for the simultaneous measurement of acrolein and 1,3-butadiene, respectively, in each puff of mainstream cigarette smoke in real time. The dual TDL system uses a 3.1l volume, 100 m astigmatic multiple pass absorption gas cell. Quantitation is based on a spectral fit that uses previously determined infrared molecular line parameters generated in our laboratory, including line positions, line strengths and nitrogen-broadened half-widths for these species. Since acrolein and ethylene absorption lines overlap and 1,3-butadiene, ethylene and propylene absorption lines overlap, the per puff deliveries of ethylene and propylene were determined since their overlapping absorption lines must be taken into account by the spectral fit. The acrolein and 1,3-butadiene total cigarette deliveries for the 1R5F Kentucky Reference cigarette were in agreement with the HPLC and GC/MS methods, respectively. The limit of detection (LOD) for 1,3-butadiene and acrolein was 4 ng/puff and 24 ng/puff, respectively, which is more than adequate to determine at which puff they break through the carbon filter. The retention and breakthrough behavior for the two primary smoke constituents depend on the cigarette design and characteristics of the carbon filter being evaluated.

Measurement of acrolein and 1,3-butadiene in a single puff of cigarette smoke using lead-salt tunable diode laser infrared spectroscopy

NASA Astrophysics Data System (ADS)

Thweatt, W. Dave; Harward, Charles N., Sr.; Parrish, Milton E.

2007-05-01

Acrolein and 1,3-butadiene in cigarette smoke generally are measured using two separate analytical methods, a carbonyl derivative HPLC method for acrolein and a volatile organic compound (VOC) GC/MS method for 1,3-butadiene. However, a single analytical method having improved sensitivity and real-time per puff measurement will offer more specific information for evaluating experimental carbon filtered cigarettes designed to reduce the smoke deliveries of these constituents. This paper describes an infrared technique using two lead-salt tunable diode lasers (TDLs) operating with liquid nitrogen cooling with emissions at 958.8 cm -1 and 891.0 cm -1 respectively for the simultaneous measurement of acrolein and 1,3-butadiene, respectively, in each puff of mainstream cigarette smoke in real time. The dual TDL system uses a 3.1 l volume, 100 m astigmatic multiple pass absorption gas cell. Quantitation is based on a spectral fit that uses previously determined infrared molecular line parameters generated in our laboratory, including line positions, line strengths and nitrogen-broadened half-widths for these species. Since acrolein and ethylene absorption lines overlap and 1,3-butadiene, ethylene and propylene absorption lines overlap, the per puff deliveries of ethylene and propylene were determined since their overlapping absorption lines must be taken into account by the spectral fit. The acrolein and 1,3-butadiene total cigarette deliveries for the 1R5F Kentucky Reference cigarette were in agreement with the HPLC and GC/MS methods, respectively. The limit of detection (LOD) for 1,3-butadiene and acrolein was 4 ng/puff and 24 ng/puff, respectively, which is more than adequate to determine at which puff they break through the carbon filter. The retention and breakthrough behavior for the two primary smoke constituents depend on the cigarette design and characteristics of the carbon filter being evaluated.

CHARACTERIZATION OF TRANSIENT PUFF EMISSIONS ...

EPA Pesticide Factsheets

Symposium Paper Transient puff emissions were characterized from burning carpet charges that were fed to a pilotscale rotary kiln combustor to assess the potential impact on emissions of using post-consumer carpet as an alternative fuel in cement kilns.

Auditory modulation of wind-elicited walking behavior in the cricket Gryllus bimaculatus.

PubMed

Fukutomi, Matasaburo; Someya, Makoto; Ogawa, Hiroto

2015-12-01

Animals flexibly change their locomotion triggered by an identical stimulus depending on the environmental context and behavioral state. This indicates that additional sensory inputs in different modality from the stimulus triggering the escape response affect the neuronal circuit governing that behavior. However, how the spatio-temporal relationships between these two stimuli effect a behavioral change remains unknown. We studied this question, using crickets, which respond to a short air-puff by oriented walking activity mediated by the cercal sensory system. In addition, an acoustic stimulus, such as conspecific 'song' received by the tympanal organ, elicits a distinct oriented locomotion termed phonotaxis. In this study, we examined the cross-modal effects on wind-elicited walking when an acoustic stimulus was preceded by an air-puff and tested whether the auditory modulation depends on the coincidence of the direction of both stimuli. A preceding 10 kHz pure tone biased the wind-elicited walking in a backward direction and elevated a threshold of the wind-elicited response, whereas other movement parameters, including turn angle, reaction time, walking speed and distance were unaffected. The auditory modulations, however, did not depend on the coincidence of the stimulus directions. A preceding sound consistently altered the wind-elicited walking direction and response probability throughout the experimental sessions, meaning that the auditory modulation did not result from previous experience or associative learning. These results suggest that the cricket nervous system is able to integrate auditory and air-puff stimuli, and modulate the wind-elicited escape behavior depending on the acoustic context. © 2015. Published by The Company of Biologists Ltd.

Stress-free automatic sleep deprivation using air puffs

PubMed Central

Gross, Brooks A.; Vanderheyden, William M.; Urpa, Lea M.; Davis, Devon E.; Fitzpatrick, Christopher J.; Prabhu, Kaustubh; Poe, Gina R.

2015-01-01

Background Sleep deprivation via gentle handling is time-consuming and personnel-intensive. New Method We present here an automated sleep deprivation system via air puffs. Implanted EMG and EEG electrodes were used to assess sleep/waking states in six male Sprague-Dawley rats. Blood samples were collected from an implanted intravenous catheter every 4 hours during the 12-hour light cycle on baseline, 8 hours of sleep deprivation via air puffs, and 8 hours of sleep deprivation by gentle handling days. Results The automated system was capable of scoring sleep and waking states as accurately as our offline version (~90% for sleep) and with sufficient speed to trigger a feedback response within an acceptable amount of time (1.76 s). Manual state scoring confirmed normal sleep on the baseline day and sleep deprivation on the two manipulation days (68% decrease in non-REM, 63% decrease in REM, and 74% increase in waking). No significant differences in levels of ACTH and corticosterone (stress hormones indicative of HPA axis activity) were found at any time point between baseline sleep and sleep deprivation via air puffs. Comparison with Existing Method There were no significant differences in ACTH or corticosterone concentrations between sleep deprivation by air puffs and gentle handling over the 8-hour period. Conclusions Our system accurately detects sleep and delivers air puffs to acutely deprive rats of sleep with sufficient temporal resolution during the critical 4-5 h post learning sleep-dependent memory consolidation period. The system is stress-free and a viable alternative to existing sleep deprivation techniques. PMID:26014662

Effect of drug load and plate coating on the particle size distribution of a commercial albuterol metered dose inhaler (MDI) determined using the Andersen and Marple-Miller cascade impactors.

PubMed

Nasr, M M; Ross, D L; Miller, N C

1997-10-01

The purpose of this study is to investigate the effect of drug load, the coating of impactor stages, and the design of cascade impactors on albuterol MDIs particle size distribution measurements. The results of the investigation will be used to explain the "loading effect" recently reported. Particle size distribution parameters of a commercial albuterol MDI were measured using both Andersen (AI) and Marple-Miller (MMI) Cascade Impactors, where plates were either left uncoated or coated with silicone or glycerin. A previously validated HPLC-EC method was used for the assay of albuterol collected by the impactor and in single spray content determinations. Coating impactor collection plates had an impact on measured MMAD and GSD values for single puff measurements but very little or no effect for the multi puff measurements. Due to particle bounce, the percent of albuterol fine particles deposited in the filter and impactor finer stages (< 1.10 microns in AI and < 1.25 microns in MMI) in uncoated single puff experiments was much higher in comparison to either coated single puff or multi-puff (coated and uncoated) measurements. Evaluation of drug load and plate coating are necessary to determine whether observed particle size distributions are representative of the generated aerosol or are the result of particle bounce and reentrainment. In order to minimize particle bounce, especially for single puff determinations, it may be useful to apply a thin layer of a sticky coating agent to the surfaces of impactor plates.

Stress-free automatic sleep deprivation using air puffs.

PubMed

Gross, Brooks A; Vanderheyden, William M; Urpa, Lea M; Davis, Devon E; Fitzpatrick, Christopher J; Prabhu, Kaustubh; Poe, Gina R

2015-08-15

Sleep deprivation via gentle handling is time-consuming and personnel-intensive. We present here an automated sleep deprivation system via air puffs. Implanted EMG and EEG electrodes were used to assess sleep/waking states in six male Sprague-Dawley rats. Blood samples were collected from an implanted intravenous catheter every 4h during the 12-h light cycle on baseline, 8h of sleep deprivation via air puffs, and 8h of sleep deprivation by gentle handling days. The automated system was capable of scoring sleep and waking states as accurately as our offline version (∼90% for sleep) and with sufficient speed to trigger a feedback response within an acceptable amount of time (1.76s). Manual state scoring confirmed normal sleep on the baseline day and sleep deprivation on the two manipulation days (68% decrease in non-REM, 63% decrease in REM, and 74% increase in waking). No significant differences in levels of ACTH and corticosterone (stress hormones indicative of HPA axis activity) were found at any time point between baseline sleep and sleep deprivation via air puffs. There were no significant differences in ACTH or corticosterone concentrations between sleep deprivation by air puffs and gentle handling over the 8-h period. Our system accurately detects sleep and delivers air puffs to acutely deprive rats of sleep with sufficient temporal resolution during the critical 4-5h post learning sleep-dependent memory consolidation period. The system is stress-free and a viable alternative to existing sleep deprivation techniques. Copyright © 2015 Elsevier B.V. All rights reserved.

Comparison of Puff Volume With Cigarettes per Day in Predicting Nicotine Uptake Among Daily Smokers.

PubMed

Krebs, Nicolle M; Chen, Allshine; Zhu, Junjia; Sun, Dongxiao; Liao, Jason; Stennett, Andrea L; Muscat, Joshua E

2016-07-01

The role of inhalation behaviors as predictors of nicotine uptake was examined in the Pennsylvania Adult Smoking Study (2012-2014), a study of 332 adults whose cigarette smoking was measured in a naturalistic environment (e.g., at home) with portable handheld topography devices. Piecewise regression analyses showed that levels of salivary cotinine, trans-3'-hydroxycotinine, and total salivary nicotine metabolites (cotinine + trans-3'-hydroxycotinine) increased linearly up to a level of about 1 pack per day (20 cigarettes per day (CPD)) (P < 0.01). Total daily puff volume (TDPV; in mL) (P < 0.05) and total daily number of puffs (P < 0.05), but not other topographical measures, increased linearly with CPD up to a level of about 1 pack per day. The mean level of cotinine per cigarette did not change above 20 CPD and was 36% lower in heavy smokers (≥20 CPD) than in lighter smokers (<20 CPD) (15.6 ng/mL vs. 24.5 ng/mL, respectively; P < 0.01). Mediation models showed that TDPV accounted for 43%-63% of the association between CPD and nicotine metabolites for smokers of <20 CPD. TDPV was the best predictor of nicotine metabolite levels in light-to-moderate smokers (1-19 CPD). In contrast, neither CPD, total daily number of puffs, nor TDPV predicted nicotine metabolite levels above 20 CPD (up to 40 CPD). Finally, although light smokers are traditionally considered less dependent on nicotine, these findings suggest that they are exposed to more nicotine per cigarette than are heavy smokers due to more frequent, intensive puffing. © The Author 2016. Published by Oxford University Press on behalf of the Johns Hopkins Bloomberg School of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Comparison of Puff Volume With Cigarettes per Day in Predicting Nicotine Uptake Among Daily Smokers

PubMed Central

Krebs, Nicolle M.; Chen, Allshine; Zhu, Junjia; Sun, Dongxiao; Liao, Jason; Stennett, Andrea L.; Muscat, Joshua E.

2016-01-01

Abstract The role of inhalation behaviors as predictors of nicotine uptake was examined in the Pennsylvania Adult Smoking Study (2012–2014), a study of 332 adults whose cigarette smoking was measured in a naturalistic environment (e.g., at home) with portable handheld topography devices. Piecewise regression analyses showed that levels of salivary cotinine, trans-3′-hydroxycotinine, and total salivary nicotine metabolites (cotinine + trans-3′-hydroxycotinine) increased linearly up to a level of about 1 pack per day (20 cigarettes per day (CPD)) (P < 0.01). Total daily puff volume (TDPV; in mL) (P < 0.05) and total daily number of puffs (P < 0.05), but not other topographical measures, increased linearly with CPD up to a level of about 1 pack per day. The mean level of cotinine per cigarette did not change above 20 CPD and was 36% lower in heavy smokers (≥20 CPD) than in lighter smokers (<20 CPD) (15.6 ng/mL vs. 24.5 ng/mL, respectively; P < 0.01). Mediation models showed that TDPV accounted for 43%–63% of the association between CPD and nicotine metabolites for smokers of <20 CPD. TDPV was the best predictor of nicotine metabolite levels in light-to-moderate smokers (1–19 CPD). In contrast, neither CPD, total daily number of puffs, nor TDPV predicted nicotine metabolite levels above 20 CPD (up to 40 CPD). Finally, although light smokers are traditionally considered less dependent on nicotine, these findings suggest that they are exposed to more nicotine per cigarette than are heavy smokers due to more frequent, intensive puffing. PMID:27313218

Edge Turbulence Imaging in Alcator C-Mod

NASA Astrophysics Data System (ADS)

Zweben, Stewart J.

2001-10-01

This talk will describe measurements and modeling of the 2-D structure of edge turbulence in Alcator C-Mod. The radial vs. poloidal structure was measured using Gas Puff Imaging (GPI) (R. Maqueda et al, RSI 72, 931 (2001), J. Terry et al, J. Nucl. Materials 290-293, 757 (2001)), in which the visible light emitted by an edge neutral gas puff (generally D or He) is viewed along the local magnetic field by a fast-gated video camera. Strong fluctuations are observed in the gas cloud light emission when the camera is gated at ~2 microsec exposure time per frame. The structure of these fluctuations is highly turbulent with a typical radial and poloidal scale of ≈1 cm, and often with local maxima in the scrape-off layer (i.e. ``blobs"). Video clips and analyses of these images will be presented along with their variation in different plasma regimes. The local time dependence of edge turbulence is measured using high-speed photodiodes viewing the gas puff emission, a scanning Langmuir probe, and also with a Princeton Scientific Instruments ultra-fast framing camera, which can make 2-D images the gas puff at up to 200,000 frames/sec. Probe measurements show that the strong turbulence region moves to the separatrix as the density limit is approached, which may be connected to the density limit (B. LaBombard et al., Phys. Plasmas 8 2107 (2001)). Comparisons of this C-Mod turbulence data will be made with results of simulations from the Drift-Ballooning Mode (DBM) (B.N. Rogers et al, Phys. Rev. Lett. 20 4396 (1998))and Non-local Edge Turbulence (NLET) codes.

Forming Super-Puffs Beyond 1 AU

NASA Astrophysics Data System (ADS)

Lee, Eve J.; Chiang, Eugene

2017-06-01

Super-puffs are an uncommon class of short-period planets seemingly too voluminous for their small masses (4-10 Rearth, 2-6 Mearth). Super-puffs most easily acquire their thick atmospheres as dust-free, rapidly cooling worlds outside ˜1AU where nebular gas is colder, less dense, and therefore less opaque. These puffy planets probably migrated in to their current orbits; they are expected to form the outer links of mean-motion resonant chains, and to exhibit atmospheric characteristics consistent with formation at large distances. I will also discuss, in general, how densities of planets can be used to infer their formation locations.

The Influence of a Mouthpiece-Based Topography Measurement Device on Electronic Cigarette User's Plasma Nicotine Concentration, Heart Rate, and Subjective Effects Under Directed and Ad Libitum Use Conditions.

PubMed

Spindle, Tory R; Hiler, Marzena M; Breland, Alison B; Karaoghlanian, Nareg V; Shihadeh, Alan L; Eissenberg, Thomas

2017-04-01

Electronic cigarettes e-cigarettes aerosolize a liquid solution often containing nicotine. e-cigarette nicotine delivery may be influenced by user puffing behaviors ("puff topography"). E-cigarette puff topography can be recorded using mouthpiece-based computerized systems. The present study sought to examine the extent to which these systems influence e-cigarette nicotine delivery and other e-cigarette associated acute effects under ad libitum use conditions. Plasma nicotine concentration, heart rate, and subjective effects were assessed in 29 experienced e-cigarette users using their preferred e-cigarette battery and liquid (≥12mg/mL nicotine) in two sessions differing only by the presence of a mouthpiece-based device. In both sessions, participants completed a directed e-cigarette use bout (10 puffs, 30-s interpuff interval) and a 90-min ad libitum bout. Puff topography was recorded in the session with the topography mouthpiece. Plasma nicotine, heart rate, and subjective effects, aside from "Did the e-cigarette Taste Good?" were independent of topography measurement (higher mean taste ratings were observed in the no topography condition). Mean (SEM) plasma nicotine concentration following the ad libitum bout was 34.3ng/mL (4.9) in the no topography condition and 35.7ng/mL (4.3) in the topography condition. Longer puff durations, longer interpuff intervals, and larger puff volumes were observed in the ad libitum relative to the directed bout. E-cigarette use significantly increased plasma nicotine concentration and heart rate while suppressing abstinence symptoms. These effects did not differ when a topography mouthpiece was present. Future studies using ad libitum e-cigarette use bouts would facilitate understanding of e-cigarette toxicant yield. No prior study has examined whether mouthpiece-based topography recording devices influence e-cigarette associated nicotine delivery, heart rate, or subjective effects under ad libitum conditions or assessed ad libitum puff topography in experienced individuals using their preferred e-cigarette battery and liquid with a mouthpiece-based computerized device. E-cigarette use significantly increased plasma nicotine concentration and heart rate while suppressing abstinence symptoms. These effects did not differ when a topography mouthpiece was present. Ad libitum puff topography differed from puff topography recorded during directed puffing. These findings suggest that future studies using ad libitum use bouts would facilitate better understanding of e-cigarette toxicant yield. © The Author 2016. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Developing the Pulsed Fission-Fusion (PuFF) Engine

NASA Technical Reports Server (NTRS)

Adams, Robert B.; Cassibry, Jason; Bradley, David; Fabisinski, Leo; Statham, Geoffrey

2014-01-01

In September 2013 the NASA Innovative Advanced Concept (NIAC) organization awarded a phase I contract to the PuFF team. Our phase 1 proposal researched a pulsed fission-fusion propulsion system that compressed a target of deuterium (D) and tritium (T) as a mixture in a column, surrounded concentrically by Uranium. The target is surrounded by liquid lithium. A high power current would flow down the liquid lithium and the resulting Lorentz force would compress the column by roughly a factor of 10. The compressed column would reach criticality and a combination of fission and fusion reactions would occur. Our Phase I results, summarized herein, review our estimates of engine and vehicle performance, our work to date to model the fission-fusion reaction, and our initial efforts in experimental analysis.

Comparison of Puff Topography, Toxicant Exposure, and Subjective Effects in Low- and High-Frequency Waterpipe Users: A Double-Blind, Placebo-Control Study

PubMed Central

Cobb, Caroline O.; Blank, Melissa D.; Morlett, Alejandra; Shihadeh, Alan; Jaroudi, Ezzat; Karaoghlanian, Nareg; Kilgalen, Barbara; Austin, Janet; Weaver, Michael F.

2015-01-01

Introduction: Clinical laboratory work among intermittent and daily waterpipe tobacco smokers has revealed significant risks for tobacco dependence and disease associated with waterpipe tobacco smoking (WTS). No studies have compared these groups directly. This study examined whether WTS frequency was associated with differential puff topography, toxicant exposure, and subjective response using a placebo-control design. Methods: Eighty participants reporting WTS of 2–5 episodes (LOW; n = 63) or ≥20 episodes (HIGH; n = 17) per month for ≥6 months completed 2 double-blind, counterbalanced 2-hr sessions that were preceded by ≥12hr of tobacco abstinence. Sessions differed by product smoked ad libitum for 45+ min: preferred brand/flavor of waterpipe tobacco (active) or a flavor-matched tobacco-free waterpipe product (placebo). Outcomes included puff topography, plasma nicotine, carboxyhemoglobin (COHb), and subjective response. Results: HIGH users had more puffs, shorter inter-puff-intervals, and a higher total puff volume for placebo relative to active, as well as relative to LOW users during placebo. Plasma nicotine concentrations increased when smoking active (but not placebo) with no significant differences between groups at 25min post-product administration. COHb increased significantly during all conditions; the largest increase was for HIGH users when smoking placebo. There was some evidence of higher baseline scores for nicotine/tobacco nicotine abstinence symptomology. Conclusions: Higher frequency waterpipe users may be more sensitive to the effects of waterpipe smoke nicotine content. Among HIGH users, higher baseline nicotine/tobacco abstinence symptoms may indicate greater nicotine dependence. These data support continued surveillance of WTS and development of dependence measures specific to this product. PMID:25257982

A Programmable Smoke Delivery Device for PET Imaging with Cigarettes Containing 11C-nicotine

PubMed Central

Zuo, Yantao; Garg, Pradeep K; Nazih, Rachid; Garg, Sudha; Rose, Jed E; Murugesan, Thangaraju; Mukhin, Alexey G

2017-01-01

Introduction PET imaging with 11C-nicotine-loaded cigarettes is a valuable tool to directly assess fast nicotine kinetics and its neuropharmacological role in tobacco dependence. To eliminate variations among puffs inhaled by subjects, this work aimed to develop a programmable smoke delivery device (SDD) to produce highly reproducible and adjustable puffs of cigarette smoke for PET experiments. New method The SDD was built around a programmable syringe pump as a smoking machine to draw a puff of smoke from a 11C-nicotine-loaded cigarette and make it available for a subject to take the smoke into the mouth and then inhale it during PET data acquisition. Brain nicotine time activity curves and total body absorbed 11C-nicotine doses (TAD) were measured in smokers who inhaled a single puff of smoke via the SDD from a 11C-nicotine-loaded cigarette. Results Nearly identical brain nicotine kinetics were observed between participants who inhaled a puff of smoke through the SDD and those who inhaled directly from a cigarette. Comparison with existing methods This new device minimizes puff variations that exist with earlier smoke delivery apparatuses which could introduce confounding factors. Conclusions The SDD is effective in delivering 11C-nicotine from the study cigarettes. Despite a 2-sec increase in aging of smoke delivered through the SDD versus smoke taken directly from a cigarette, the difference in brain nicotine kinetics after 11C-nicotine delivery with and without use of the SDD is negligible. This refined device may be useful for future research on the deposition and pharmacokinetics of nicotine inhaled with tobacco smoke. PMID:28347784

A programmable smoke delivery device for PET imaging with cigarettes containing 11C-nicotine.

PubMed

Zuo, Yantao; Garg, Pradeep K; Nazih, Rachid; Garg, Sudha; Rose, Jed E; Murugesan, Thangaraju; Mukhin, Alexey G

2017-05-01

PET imaging with 11 C-nicotine-loaded cigarettes is a valuable tool to directly assess fast nicotine kinetics and its neuropharmacological role in tobacco dependence. To eliminate variations among puffs inhaled by subjects, this work aimed to develop a programmable smoke delivery device (SDD) to produce highly reproducible and adjustable puffs of cigarette smoke for PET experiments. The SDD was built around a programmable syringe pump as a smoking machine to draw a puff of smoke from a 11 C-nicotine-loaded cigarette and make it available for a subject to take the smoke into the mouth and then inhale it during PET data acquisition. Brain nicotine time activity curves and total body absorbed 11 C-nicotine doses (TAD) were measured in smokers who inhaled a single puff of smoke via the SDD from a 11 C-nicotine-loaded cigarette. Nearly identical brain nicotine kinetics were observed between participants who inhaled a puff of smoke through the SDD and those who inhaled directly from a cigarette. This new device minimizes puff variations that exist with earlier smoke delivery apparatuses which could introduce confounding factors. The SDD is effective in delivering 11 C-nicotine from the study cigarettes. Despite a 2-s increase in aging of smoke delivered through the SDD versus smoke taken directly from a cigarette, the difference in brain nicotine kinetics after 11 C-nicotine delivery with and without use of the SDD is negligible. This refined device may be useful for future research on the deposition and pharmacokinetics of nicotine inhaled with tobacco smoke. Copyright © 2017 Elsevier B.V. All rights reserved.

A Real-Time Fast-Flow Tube Study of VOC and Particulate Emissions from Electronic, Potentially Reduced-Harm, Conventional, and Reference Cigarettes

PubMed Central

Blair, Sandra L.; Epstein, Scott A.; Nizkorodov, Sergey A.; Staimer, Norbert

2015-01-01

Tobacco-free electronic cigarettes (e-cigarettes), which are currently not regulated by the FDA, have become widespread as a “safe” form of smoking. One approach to evaluate the potential toxicity of e-cigarettes and other types of potentially “reduced-harm” cigarettes is to compare their emissions of volatile organic compounds (VOCs), including reactive organic electrophillic compounds such as acrolein, and particulate matter to those of conventional and reference cigarettes. Our newly designed fast-flow tube system enabled us to analyze VOC composition and particle number concentration in real-time by promptly diluting puffs of mainstream smoke obtained from different brands of combustion cigarettes and e-cigarettes. A proton transfer reaction time-of-flight mass spectrometer (PTRMS) was used to analyze real-time cigarette VOC emissions with a 1 s time resolution. Particles were detected with a condensation particle counter (CPC). This technique offers real-time analysis of VOCs and particles in each puff without sample aging and does not require any sample pretreatment or extra handling. Several important determining factors in VOC and particle concentration were investigated: (1) puff frequency; (2) puff number; (3) tar content; (4) filter type. Results indicate that electronic cigarettes are not free from acrolein and acetaldehyde emissions and produce comparable particle number concentrations to those of combustion cigarettes, more specifically to the 1R5F reference cigarette. Unlike conventional cigarettes, which emit different amounts of particles and VOCs each puff, there was no significant puff dependence in the e-cigarette emissions. Charcoal filter cigarettes did not fully prevent the emission of acrolein and other VOCs. PMID:26726281

Changes in puffing behavior among smokers who switched from tobacco to electronic cigarettes

PubMed Central

Lee, Yong Hee; Gawron, Michal; Goniewicz, Maciej Lukasz

2015-01-01

Introduction Nicotine intake from electronic cigarette (e-cigarettes) increases with user’s experience. This suggests that smokers who switched from tobacco to electronic cigarettes compensate for nicotine over the time to get as much nicotine as they need. One of the mechanism by which smokers may compensate for nicotine is by modifying their puffing behavior. The aim of the study was to assess the changes in puffing behavior after switching from conventional to electronic cigarettes among regular smokers. Materials and Methods Twenty smokers (11 female, aged 31±10, CPD 16±8, FTND 4±3, and exhaled CO 16±17 (mean±SD)) who were naïve to e-cigarettes participated in this study. They were asked to substitute their regular tobacco cigarettes with first generation e-cigarettes (labelled 18 mg nicotine) for two weeks. Puffing topography (number of puffs, puff volume, intervals between puffs, and average puff flow rate) was measured at the initial use (baseline), as well as after one and two weeks of product use. We tested changes in puffing topography outcomes using repeated measures ANOVA. Results We found that after one week of using e-cigarettes, participants significantly increased the average time they puffed on e-cigarettes from 2.2±0.1 (mean±SEM) to 3.1±0.3 sec (p<0.05). The average puff flow rate decreased from 30.6±2.3 to 25.1±1.8 ml/sec after one week of e-cigarette use (p<0.05). Conclusions Our data show that smokers modify their puffing behavior after switching from tobacco to electronic cigarettes by taking longer and slower puffs. The potential reason for changing puffing behavior is to compensate for less efficient nicotine delivery from e-cigarettes. PMID:25930009

Changes in puffing behavior among smokers who switched from tobacco to electronic cigarettes.

PubMed

Lee, Yong Hee; Gawron, Michal; Goniewicz, Maciej Lukasz

2015-09-01

Nicotine intake from electronic cigarette (e-cigarettes) increases with user's experience. This suggests that smokers who switched from tobacco to electronic cigarettes compensate for nicotine over time to get as much nicotine as they need. One of the mechanisms by which smokers may compensate for nicotine is by modifying their puffing behavior. The aim of the study was to assess the changes in puffing behavior after switching from conventional to electronic cigarettes among regular smokers. Twenty smokers (11 female, aged 31±10, CPD 16±8, FTND 4±3, and exhaled CO 16±17 (mean±SD)) who were naïve to e-cigarettes participated in this study. They were asked to substitute their regular tobacco cigarettes with first generation e-cigarettes (labeled 18mg nicotine) for two weeks. Puffing topography (number of puffs, puff volume, intervals between puffs, and average puff flow rate) was measured at the initial use (baseline), as well as after one and two weeks of product use. We tested changes in puffing topography outcomes using repeated measures ANOVA. We found that after one week of using e-cigarettes, participants significantly increased the average time they puffed on e-cigarettes from 2.2±0.1 (mean±SEM) to 3.1±0.3s (p<0.05). The average puff flow rate decreased from 30.6±2.3 to 25.1±1.8ml/s after one week of e-cigarette use (p<0.05). Our data show that smokers modify their puffing behavior after switching from tobacco to electronic cigarettes by taking longer and slower puffs. The potential reason for changing puffing behavior is to compensate for less efficient nicotine delivery from e-cigarettes. Copyright © 2015 Elsevier Ltd. All rights reserved.

What reaches the antenna? How to calibrate odor flux and ligand-receptor affinities.

PubMed

Andersson, Martin N; Schlyter, Fredrik; Hill, Sharon Rose; Dekker, Teun

2012-06-01

Physiological studies on olfaction frequently ignore the airborne quantities of stimuli reaching the sensory organ. We used a gas chromatography-calibrated photoionization detector to estimate quantities released from standard Pasteur pipette stimulus cartridges during repeated puffing of 27 compounds and verified how lack of quantification could obscure olfactory sensory neuron (OSN) affinities. Chemical structure of the stimulus, solvent, dose, storage condition, puff interval, and puff number all influenced airborne quantities. A model including boiling point and lipophilicity, but excluding vapor pressure, predicted airborne quantities from stimuli in paraffin oil on filter paper. We recorded OSN responses of Drosophila melanogaster, Ips typographus, and Culex quinquefasciatus, to known quantities of airborne stimuli. These demonstrate that inferred OSN tuning width, ligand affinity, and classification can be confounded and require stimulus quantification. Additionally, proper dose-response analysis shows that Drosophila AB3A OSNs are not promiscuous, but highly specific for ethyl hexanoate, with other earlier proposed ligands 10- to 10 000-fold less potent. Finally, we reanalyzed published Drosophila OSN data (DoOR) and demonstrate substantial shifts in affinities after compensation for quantity and puff number. We conclude that consistent experimental protocols are necessary for correct OSN classification and present some simple rules that make calibration, even retroactively, readily possible.

Maximize Liquid Oil Production from Shale Oil and Gas Condensate Reservoirs by Cyclic Gas Injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheng, James; Li, Lei; Yu, Yang

The current technology to produce shale oil reservoirs is the primary depletion using fractured wells (generally horizontal wells). The oil recovery is less than 10%. The prize to enhance oil recovery (EOR) is big. Based on our earlier simulation study, huff-n-puff gas injection has the highest EOR potential. This project was to explore the potential extensively and from broader aspects. The huff-n-puff gas injection was compared with gas flooding, water huff-n-puff and waterflooding. The potential to mitigate liquid blockage was also studied and the gas huff-n-puff method was compared with other solvent methods. Field pilot tests were initiated but terminatedmore » owing to the low oil price and the operator’s budget cut. To meet the original project objectives, efforts were made to review existing and relevant field projects in shale and tight reservoirs. The fundamental flow in nanopores was also studied.« less

Multimodality of Ca2+ signaling in rat atrial myocytes.

PubMed

Morad, Martin; Javaheri, Ashkan; Risius, Tim; Belmonte, Steve

2005-06-01

It has been suggested that the multiplicity of Ca(2+) signaling pathways in atrial myocytes may contribute to the variability of its function. This article reports on a novel Ca(2+) signaling cascade initiated by mechanical forces induced by "puffing" of solution onto the myocytes. Ca(i) transients were measured in fura-2 acetoxymethyl (AM) loaded cells using alternating 340- and 410-nm excitation waves at 1.2 kHz. Pressurized puffs of bathing solutions, applied by an electronically controlled micro-barrel system, activated slowly (approximately 300 ms) developing Ca(i) transients that lasted 1,693 +/- 68 ms at room temperature. Subsequent second and third puffs, applied at approximately 20 s intervals activated significantly smaller or no Ca(i) transients. Puff-triggered Ca(i) transients could be reactivated once again following caffeine (10 mM)-induced release of Ca(2+) from sarcoplasmic reticulum (SR). Puff-triggered Ca(i) transients were independent of [Ca(2+)](o), and activation of voltage-gated Ca(2+) or cationic stretch channels or influx of Ca(2+) on Na(+)/Ca(2+)exchanger, because puffing solution containing no Ca(2+), 10 microM diltiazem, 1 mM Cd(2+), 5 mM Ni(2+), or 100 microM Gd(3+) failed to suppress them. Puff-triggered Ca(i) transients were enhanced in paced compared to quiescent myocytes. Electrically activated Ca(i) transients triggered during the time course of puff-induced transients were unaltered, suggesting functionally separate Ca(2+) pools. Contribution of inositol 1,4,5-triphosphate (IP(3))-gated or mitochondrial Ca(2+) pools or modulation of SR stores by nitric oxide/nitric oxide synthase (NO/NOS) signaling were evaluated using 0.5 to 500 microM 2-aminoethoxydiphenyl borate (2-APB) and 0.1 to 1 microM carbonylcyanide-p-trifluoromethoxyphenylhydrazone (FCCP), and 1 mM Nomega-Nitro-L-arginine methyl ester (L-NAME) and 7-nitroindizole, respectively. Only FCCP appeared to significantly suppress the puff-triggered Ca(i) transients. It was concluded that neither Ca(2+) influx nor depolarization was required for activation of this signaling pathway. These studies suggest that pressurized puffs of solutions activate a mechanically sensitive receptor, which signals in turn the release of Ca(2+) from a limited Ca(2+) store of mitochondria. How mechanical forces are sensed and transmitted to mitochondria to induce Ca(2+) release and what role such a Ca(2+) signaling pathway plays in the physiology or pathophysiology of the heart remain to be worked out.

EFFECTS OF WIND SHEAR ON POLLUTION DISPERSION. (R827929)

EPA Science Inventory

Using an accurate numerical method for simulating the advection and diffusion of pollution puffs, it is demonstrated that point releases of pollution grow into a shape reflecting the vertical wind shear profile experienced by the puff within a time scale less than 4 h. Fo...

Liquid oil production from shale gas condensate reservoirs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheng, James J.

A process of producing liquid oil from shale gas condensate reservoirs and, more particularly, to increase liquid oil production by huff-n-puff in shale gas condensate reservoirs. The process includes performing a huff-n-puff gas injection mode and flowing the bottom-hole pressure lower than the dew point pressure.

Evaluation of the effect of ammonia on nicotine pharmacokinetics using rapid arterial sampling.

PubMed

McKinney, Diana L; Gogova, Maria; Davies, Bruce D; Ramakrishnan, Viswanathan; Fisher, Kelly; Carter, W Hans; Karnes, H Thomas; Garnett, William R; Iyer, Sunil S; Somani, Amit A; Kobal, Gerd; Barr, William H

2012-05-01

The nicotine bolus theory states that the dependence-producing potential of cigarettes relates to a rapid increase in nicotine at brain receptor sites. It has been suggested that ammonia, a compound typically found in tobacco products, further increases the amount of nicotine absorbed and its absorption rate. The aim of this study was to determine whether different ammonia yields in cigarettes affected the rate or amount of nicotine absorption from the lungs to arterial circulation. 34 adult smokers received 3 separate puffs from each of 2 test cigarettes with different ammonia yields (ammonia in smoke: 10.1 μg per cigarette vs. 18.9 μg per cigarette), followed by rapid radial arterial blood sampling (maximum one sample per second) with 30 min between puffs. Arterial blood samples were assayed for nicotine by liquid chromatography tandem mass spectrometry. Pharmacokinetic modeling was performed and the two test cigarettes were assessed for bioequivalence. No significant differences were found in area under the curve, C(max), or T((max)) and the 2 test cigarettes were found to be bioequivalent based on 2 one-sided tests at a significance level of 5%. In addition, the zero-order rate constant (k(0)) obtained from the initial slope of the curves and the model-dependent first-order rate constant (k(a)) were not significantly different. This study provides strong evidence that the different ammonia yields of the test cigarettes had no impact on nicotine pharmacokinetics; thus, the ammonia did not increase the rate or amount of nicotine absorption from a puff of cigarette smoke.

SIMULATION OF A REACTING POLLUTANT PUFF USING AN ADAPTIVE GRID ALGORITHM

EPA Science Inventory

A new dynamic solution adaptive grid algorithm DSAGA-PPM, has been developed for use in air quality modeling. In this paper, this algorithm is described and evaluated with a test problem. Cone-shaped distributions of various chemical species undergoing chemical reactions are rota...

Development of a new gas puff imaging diagnostic on the HL-2A tokamak

NASA Astrophysics Data System (ADS)

Yuan, B.; Xu, M.; Yu, Y.; Zang, L.; Hong, R.; Chen, C.; Wang, Z.; Nie, L.; Ke, R.; Guo, D.; Wu, Y.; Long, T.; Gong, S.; Liu, H.; Ye, M.; Duan, X.; HL-2A team

2018-03-01

A new gas puff imaging (GPI) diagnostic has been developed on the HL-2A tokamak to study two-dimensional plasma edge turbulence in poloidal vs. radial plane. During a discharge, neutral helium or deuterium gas is puffed at the edge of the plasma through a rectangular multi\

SPRAYTRAN 1.0 User’s Guide: A GIS-Based Atmospheric Spray Droplet Dispersion Modeling System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allwine, K Jerry; Rutz, Frederick C.; Droppo, James G.

SPRAY TRANsport (SPRAYTRAN) is a comprehensive dispersion modeling system that is used to simulate the offsite drift of pesticides from spray applications. SPRAYTRAN functions as a console application within Environmental System Research Institute’s ArcMap Geographic Information System (Version 9.x) and integrates the widely-used, U.S. Environmental Protection Agency (EPA)-approved CALifornia PUFF (CALPUFF) dispersion model and model components to simulate longer-range transport and diffusion in variable terrain and spatially/temporally varying meteorological (e.g., wind) fields. Area sources, which are used to define spray blocks in SPRAYTRAN, are initialized using output files generated from a separate aerial-spray-application model called AGDISP (AGricultural DISPersal). The AGDISPmore » model is used for estimating the amount of pesticide deposited to the spray block based on spraying characteristics (e.g., pesticide type, spray nozzles, and aircraft type) and then simulating the near-field (less than 300-m) drift from a single pesticide application. The fraction of pesticide remaining airborne from the AGDISP near-field simulation is then used by SPRAYTRAN for simulating longer-range (greater than 300 m) drift and deposition of the pesticide.« less

Getting a Puff: A Social Learning Test of Adolescents Smoking

ERIC Educational Resources Information Center

Monroe, Jacquelyn

2004-01-01

This article is a description of a study that sought to examine the applicability of Ronald Akers' social learning theory. According to Akers' theory, differential associations with smokers, differential reinforcements for smoking, favorable definitions of smoking and the availability of role models (imitation) offer an explanation as to why…

In vivo effects of ecdysterone on puff formation, and RNA and protein synthesis in the salivary glands of Rhynchosciara americana.

PubMed

Alvarenga, C A; Winter, C E; Stocker, A J; Pueyo, M T; Lara, F J

1991-01-01

1. Fourth-instar larvae of Rhynchosciara americana were injected with the insect molting hormone, ecdysterone, giving final hemolymph concentrations from 4.46 to 223 microM. 2. Induction of the DNA puff, B2b, in the proximal (S1) region of the salivary glands of Rhynchosciara americana by 22.6 microM ecdysterone, was accompanied by the production of an mRNA and a polypeptide with the same characteristics as B2b products produced during normal development. This mRNA and polypeptide were restricted to the proximal region of the gland, as is the B2b puff. 3. Synthesis of other poly(A)+RNAs was also stimulated in S1 by ecdysterone, and other puffs that appear during normal development were induced. However, rRNA production in S1 goes through a pattern of inhibition, followed by recovery when B2b is puffed, and subsequent inhibition. 4. Low molecular weight RNA, with a peak in the region of 4S, is stimulated after ecdysterone administration.

Buoyancy Effects in Strongly-Pulsed, Turbulent Diffusion Flames

NASA Astrophysics Data System (ADS)

Hermanson, James; Johari, Hamid; Stocker, Dennis; Hegde, Uday

2004-11-01

Buoyancy effects in pulsed, turbulent flames are studied in microgravity in a 2.2 s drop-tower. The fuel is pure ethylene or a 50/50 mixture with nitrogen; the oxidizer co-flow is either air or 30% oxygen in nitrogen. A fast solenoid valve fully modulates (shuts off) the fuel flow between pulses. The jet Reynolds number is 5000 with a nozzle i.d. of 2 mm. For short injection times and small duty cycle (jet-on fraction), compact, puff-like flames occur. The invariance in flame length of these puffs with buoyancy is due to offsetting changes in puff celerity and burnout time. Buoyancy does impact interacting flame puffs, with the flame length generally increasing with injection duty cycle. The mean centerline temperatures for all flames are generally higher in microgravity than in normal gravity. The transition in temperatures with increasing injection time is more gradual in micro-g than in 1-g. These observations can be explained in terms of the local duty cycle in the flame and differences in entrainment in normal- vs. microgravity.

Week Long Topography Study of Young Adults Using Electronic Cigarettes in Their Natural Environment.

PubMed

Robinson, R J; Hensel, E C; Roundtree, K A; Difrancesco, A G; Nonnemaker, J M; Lee, Y O

2016-01-01

Results of an observational, descriptive study quantifying topography characteristics of twenty first generation electronic nicotine delivery system users in their natural environment for a one week observation period are presented. The study quantifies inter-participant variation in puffing topography between users and the intra-participant variation for each user observed during one week of use in their natural environment. Puff topography characteristics presented for each user include mean puff duration, flow rate and volume for each participant, along with descriptive statistics of each quantity. Exposure characteristics including the number of vaping sessions, total number of puffs and cumulative volume of aerosol generated from ENDS use (e-liquid aerosol) are reported for each participant for a one week exposure period and an effective daily average exposure. Significant inter-participant and intra-participant variation in puff topography was observed. The observed range of natural use environment characteristics is used to propose a set of topography protocols for use as command inputs to drive machine-puffed electronic nicotine delivery systems in a controlled laboratory environment.

Week Long Topography Study of Young Adults Using Electronic Cigarettes in Their Natural Environment

PubMed Central

Roundtree, K. A.; Difrancesco, A. G.; Nonnemaker, J. M.; Lee, Y. O.

2016-01-01

Results of an observational, descriptive study quantifying topography characteristics of twenty first generation electronic nicotine delivery system users in their natural environment for a one week observation period are presented. The study quantifies inter-participant variation in puffing topography between users and the intra-participant variation for each user observed during one week of use in their natural environment. Puff topography characteristics presented for each user include mean puff duration, flow rate and volume for each participant, along with descriptive statistics of each quantity. Exposure characteristics including the number of vaping sessions, total number of puffs and cumulative volume of aerosol generated from ENDS use (e-liquid aerosol) are reported for each participant for a one week exposure period and an effective daily average exposure. Significant inter-participant and intra-participant variation in puff topography was observed. The observed range of natural use environment characteristics is used to propose a set of topography protocols for use as command inputs to drive machine-puffed electronic nicotine delivery systems in a controlled laboratory environment. PMID:27736944

Efficient Neutron Production from a Novel Configuration of Deuterium Gas-Puff Z-Pinch

NASA Astrophysics Data System (ADS)

Klir, D.; Kubes, P.; Rezac, K.; Cikhardt, J.; Kravarik, J.; Sila, O.; Shishlov, A. V.; Kovalchuk, B. M.; Ratakhin, N. A.; Kokshenev, V. A.; Labetsky, A. Yu.; Cherdizov, R. K.; Fursov, F. I.; Kurmaev, N. E.; Dudkin, G. N.; Nechaev, B. A.; Padalko, V. N.; Orcikova, H.; Turek, K.

2014-03-01

A novel configuration of a deuterium z pinch has been used to generate fusion neutrons. Injecting an outer hollow cylindrical plasma shell around an inner deuterium gas puff, neutron yields from DD reactions reached Yn=(2.9±0.3)×1012 at 700 ns implosion time and 2.7 MA current. Such a neutron yield means a tenfold increase in comparison with previous deuterium gas puff experiments at the same current generator. The increase of beam-target yields was obtained by a larger amount of current assembled on the z-pinch axis, and subsequently by higher induced voltage and higher energies of deuterons. A stack of CR-39 track detectors on the z-pinch axis showed hydrogen ions up to 38 MeV. Maximum neutron energies of 15 and 22 MeV were observed by radial and axial time-of-flight detectors, respectively. The number of DD neutrons per one joule of stored plasma energy approached 5×107. This implies that deuterium gas puff z pinches belong to the most efficient plasma-based sources of DD neutrons.

Nicotine and Carbon Monoxide Exposure from Inhalation of Cigarillo Smoke

PubMed Central

Koszowski, Bartosz; Rosenberry, Zachary R.; Kanu, Alieu; Viray, Lauren C.; Potts, Jennifer L.; Pickworth, Wallace B.

2015-01-01

Background There has been an increase in the use of cigarillos in the US. People who smoke cigarillos typically also regularly smoke cigarettes (dual users). Methods We compared puffing topography, biomarkers of acute exposure [exhaled carbon monoxide (COex) and plasma nicotine] and physiologic effects from usual brand cigarette and Black & Mild cigarillo smoking in dual users (N=23) in two laboratory sessions. Results Participants (21 men) smoked an average of 17.5 cigarettes/day. Cigarillo consumption varied widely from as few as 1/week to daily. Participants were highly nicotine dependent (average FTND score: 6.3). There were statistically significant differences in smoking behavior between cigarette and cigarillo smoking in time to smoke, number of puffs, and total puff volume (all P<0.001). Average puff duration, interpuff interval average puff volume, and puff velocity did not differ between cigarettes and cigarillos. Nicotine boost was similar after both cigarettes and cigarillos. COex boost was significantly greater after cigarillo smoking compared to cigarette smoking (P<0.001). Conclusions The smoking pattern and exposure profile indicate that dual users inhale cigarillo smoke just as they inhale cigarette smoke thereby exposing themselves to considerable amounts of nicotine and other components of tobacco smoke. COex exposure results imply that cigarillo smoking may be associated with higher exposure to smoke-delivered volatile components of mainstream cigarillo smoke including carcinogens when compared to cigarettes. Impact The findings that cigarillos and cigarettes are smoked similarly in dual users are relevant to health and regulatory considerations on cigar products. PMID:26459155

Smoking Topography among Korean Smokers: Intensive Smoking Behavior with Larger Puff Volume and Shorter Interpuff Interval.

PubMed

Kim, Sungroul; Yu, Sol

2018-05-18

The difference of smoker's topography has been found to be a function many factors, including sex, personality, nicotine yield, cigarette type (i.e., flavored versus non-flavored) and ethnicity. We evaluated the puffing behaviors of Korean smokers and its association with smoking-related biomarker levels. A sample of 300 participants was randomly recruited from metropolitan areas in South Korea. Topography measures during a 24-hour period were obtained using a CReSS pocket device. Korean male smokers smoked two puffs less per cigarette compared to female smokers (15.0 (13.0⁻19.0) vs. 17.5 (15.0⁻21.0) as the median (Interquartile range)), but had a significantly larger puff volume (62.7 (52.7⁻75.5) mL vs. 53.5 (42.0⁻64.2) mL); p = 0.012). The interpuff interval was similar between men and women (8.9 (6.5⁻11.2) s vs. 8.3 (6.2⁻11.0) s; p = 0.122) but much shorter than other study results. A dose-response association ( p = 0.0011) was observed between daily total puff volumes and urinary cotinine concentrations, after controlling for sex, age, household income level and nicotine addiction level. An understanding of the difference of topography measures, particularly the larger puff volume and shorter interpuff interval of Korean smokers, may help to overcome a potential underestimation of internal doses of hazardous byproducts of smoking.

Comparison of True and Smoothed Puff Profile Replication on Smoking Behavior and Mainstream Smoke Emissions

PubMed Central

2015-01-01

To estimate exposures to smokers from cigarettes, smoking topography is typically measured and programmed into a smoking machine to mimic human smoking, and the resulting smoke emissions are tested for relative levels of harmful constituents. However, using only the summary puff data—with a fixed puff frequency, volume, and duration—may underestimate or overestimate actual exposure to smoke toxins. In this laboratory study, we used a topography-driven smoking machine that faithfully reproduces a human smoking session and individual human topography data (n = 24) collected during previous clinical research to investigate if replicating the true puff profile (TP) versus the mathematically derived smoothed puff profile (SM) resulted in differences in particle size distributions and selected toxic/carcinogenic organic compounds from mainstream smoke emissions. Particle size distributions were measured using an electrical low pressure impactor, the masses of the size-fractionated fine and ultrafine particles were determined gravimetrically, and the collected particulate was analyzed for selected particle-bound, semivolatile compounds. Volatile compounds were measured in real time using a proton transfer reaction-mass spectrometer. By and large, TP levels for the fine and ultrafine particulate masses as well as particle-bound organic compounds were slightly lower than the SM concentrations. The volatile compounds, by contrast, showed no clear trend. Differences in emissions due to the use of the TP and SM profiles are generally not large enough to warrant abandoning the procedures used to generate the simpler smoothed profile in favor of the true profile. PMID:25536227

Combined varenicline and naltrexone treatment reduces smoking topography intensity in heavy-drinking smokers.

PubMed

Roche, Daniel J O; Bujarski, Spencer; Hartwell, Emily; Green, ReJoyce; Ray, Lara A

2015-07-01

Heavy drinking smokers constitute a distinct sub-population of smokers for whom traditional smoking cessation therapies may not be effective. Recent evidence suggested that combined varenicline (VAR) and naltrexone (NTX) therapy may be more efficacious than either monotherapy alone in reducing smoking and drinking-related behavior in this population. The manner in which individuals smoke a cigarette (i.e., smoking topography) may be predictive of smoking cessation outcomes, yet the effects of smoking pharmacotherapies on puffing behavior have not been thoroughly examined. Therefore, the current double-blind medication study examined the effects of VAR alone (1mg BID), low dose NTX alone (25mg QD), the combination of VAR+NTX, and placebo on smoking topography measures in heavy drinking, non-treatment seeking daily smokers (n=120). After a 9-day titration period, participants completed a laboratory session in which they smoked their first cigarette of the day using a smoking topography device following 12h of nicotine abstinence and consumption of an alcoholic beverage (BrAC=0.06g/dl). The primary measures were puff count, volume, duration, and velocity and inter-puff interval (IPI). Independent of medication group, puff velocity and IPI increased, while puff volume and duration decreased, over the course of the cigarette. The active medication groups, vs. the placebo group, had significantly blunted puff duration and velocity slopes over the course of the cigarette, and this effect was particularly evident in the VAR+NTX group. Additionally, the VAR+NTX group demonstrated lower average IPI than the monotherapy groups and lower average puff volume than all other groups. These results suggest that smoking pharmacotherapies, particularly the combination of VAR+NTX, alter smoking topography in heavy drinking smokers, producing a pattern of less intense puffing behavior. As smoking topography has been predictive of the ability to quit smoking, future studies should examine how smoking pharmacotherapies' effects on puffing behavior relate to smoking cessation outcomes. Copyright © 2015. Published by Elsevier Inc.

Combined Varenicline and naltrexone treatment reduces smoking topography intensity in heavy-drinking smokers

PubMed Central

Roche, Daniel J.O.; Bujarski, Spencer; Hartwell, Emily; Green, ReJoyce; Ray, Lara A.

2015-01-01

Heavy drinking smokers constitute a distinct sub-population of smokers for whom traditional smoking cessation therapies may not be effective. Recent evidence suggested that combined varenicline (VAR) and naltrexone (NTX) therapy may be more efficacious than either monotherapy alone in reducing smoking and drinking-related behavior in this population. The manner in which individuals smoke a cigarette (i.e., smoking topography) may be predictive of smoking cessation outcomes, yet the effects of smoking pharmacotherapies on puffing behavior have not been thoroughly examined. Therefore, the current double-blind medication study examined the effects of VAR alone (1mg BID), low dose NTX alone (25mg QD), the combination of VAR+NTX, and placebo on smoking topography measures in heavy drinking, non-treatment seeking daily smokers (n=120). After a 9-day titration period, participants completed a laboratory session in which they smoked their first cigarette of the day using a smoking topography device following 12-hrs of nicotine abstinence and consumption of an alcoholic beverage (BrAC = 0.06 g/dl). The primary measures were puff count, volume, duration, and velocity and inter-puff interval (IPI). Independent of medication group, puff velocity and IPI increased, while puff volume and duration decreased, over the course of the cigarette. The active medication groups, vs. the placebo group, had significantly blunted puff duration and velocity slopes over the course of the cigarette, and this effect was particularly evident in the VAR+NTX group. Additionally, the VAR+NTX group demonstrated lower average IPI than the monotherapy groups and lower average puff volume than all other groups. These results suggest that smoking pharmacotherapies, particularly the combination of VAR+NTX, alter smoking topography in heavy drinking smokers, producing a pattern of less intense puffing behavior. As smoking topography has been predictive of the ability to quit smoking, future studies should examine how smoking pharmacotherapies’ effects on puffing behavior relate to smoking cessation outcomes. PMID:25933795

High Energy Electron Detectors on Sphinx

NASA Astrophysics Data System (ADS)

Thompson, J. R.; Porte, A.; Zucchini, F.; Calamy, H.; Auriel, G.; Coleman, P. L.; Bayol, F.; Lalle, B.; Krishnan, M.; Wilson, K.

2008-11-01

Z-pinch plasma radiation sources are used to dose test objects with K-shell (˜1-4keV) x-rays. The implosion physics can produce high energy electrons (> 50keV), which could distort interpretation of the soft x-ray effects. We describe the design and implementation of a diagnostic suite to characterize the electron environment of Al wire and Ar gas puff z-pinches on Sphinx. The design used ITS calculations to model detector response to both soft x-rays and electrons and help set upper bounds to the spurious electron flux. Strategies to discriminate between the known soft x-ray emission and the suspected electron flux will be discussed. H.Calamy et al, ``Use of microsecond current prepulse for dramatic improvements of wire array Z-pinch implosion,'' Phys Plasmas 15, 012701 (2008) J.A.Halbleib et al, ``ITS: the integrated TIGER series of electron/photon transport codes-Version 3.0,'' IEEE Trans on Nuclear Sci, 39, 1025 (1992)

Can one puff really make an adolescent addicted to nicotine? A critical review of the literature

PubMed Central

2010-01-01

Rationale In the past decade, there have been various attempts to understand the initiation and progression of tobacco smoking among adolescents. One line of research on these issues has made strong claims regarding the speed in which adolescents can become physically and mentally addicted to smoking. According to these claims, and in contrast to other models of smoking progression, adolescents can lose autonomy over their smoking behavior after having smoked one puff in their lifetime and never having smoked again, and can become mentally and physically "hooked on nicotine" even if they have never smoked a puff. Objectives To critically examine the conceptual and empirical basis for the claims made by the "hooked on nicotine" thesis. Method We reviewed the major studies on which the claims of the "hooked on nicotine" research program are based. Results The studies we reviewed contained substantive conceptual and methodological flaws. These include an untenable and idiosyncratic definition of addiction, use of single items or of very lenient criteria for diagnosing nicotine dependence, reliance on responders' causal attributions in determining physical and mental addiction to nicotine and biased coding and interpretation of the data. Discussion The conceptual and methodological problems detailed in this review invalidate many of the claims made by the "hooked on nicotine" research program and undermine its contribution to the understanding of the nature and development of tobacco smoking in adolescents. PMID:21067587

Olive Oil Based Emulsions in Frozen Puff Pastry Production

NASA Astrophysics Data System (ADS)

Gabriele, D.; Migliori, M.; Lupi, F. R.; de Cindio, B.

2008-07-01

Puff pastry is an interesting food product having different industrial applications. It is obtained by laminating layers of dough and fats, mainly shortenings or margarine, having specific properties which provides required spreading characteristic and able to retain moisture into dough. To obtain these characteristics, pastry shortenings are usually saturated fats, however the current trend in food industry is mainly oriented towards unsatured fats such as olive oil, which are thought to be safer for human health. In the present work, a new product, based on olive oil, was studied as shortening replacer in puff pastry production. To ensure the desired consistency, for the rheological matching between fat and dough, a water-in-oil emulsion was produced based on olive oil, emulsifier and a hydrophilic thickener agent able to increase material structure. Obtained materials were characterized by rheological dynamic tests in linear viscoelastic conditions, aiming to setup process and material consistency, and rheological data were analyzed by using the weak gel model. Results obtained for tested emulsions were compared to theological properties of a commercial margarine, adopted as reference value for texture and stability. Obtained emulsions are characterized by interesting rheological properties strongly dependent on emulsifier characteristics and water phase composition. However a change in process temperature during fat extrusion and dough lamination seems to be necessary to match properly typical dough rheological properties.

Effect of Permeability of Tipping Paper on Cigarette Burning Temperature and the Property of Mainstream Smoke

NASA Astrophysics Data System (ADS)

Yao, Zhen-Yu; Shen, Yan; Huang, Hai-Qun; Xu, Ji-Cang

2016-05-01

Cigarette smoke analysis of tipping paper with different permeability was carried out. The infrared thermal imager was used to measure burning temperature of cigarette with different permeability tipping paper. The results indicated that with the increase of tipping paper permeability, Tar, CO and nicotine in cigarette mainstream were significantly linear decreased, puff count was increased. Tipping paper permeability had a great influence on cigarette burning temperature. With the increase of tipping paper permeability, the third puff burning temperature and the average peak temperature values were dropped obviously, but the changes of smoldering temperature were not obvious. In addition, smoldering average temperature was significantly lower than the third puff burning temperature and peak temperature.

Nicotine and carbon monoxide exposure from inhalation of cigarillo smoke.

PubMed

Koszowski, Bartosz; Rosenberry, Zachary R; Kanu, Alieu; Viray, Lauren C; Potts, Jennifer L; Pickworth, Wallace B

2015-12-01

There has been an increase in the use of cigarillos in the US. People who smoke cigarillos typically also regularly smoke cigarettes (dual users). We compared puffing topography, biomarkers of acute exposure [exhaled carbon monoxide (COex) and plasma nicotine] and physiologic effects from usual brand cigarette and Black & Mild cigarillo smoking in dual users (N=23) in two laboratory sessions. Participants (21 men) smoked an average of 17.5cigarettes/day. Cigarillo consumption varied widely from as few as 1/week to daily. Participants were highly nicotine dependent (average FTND score: 6.3). There were statistically significant differences in smoking behavior between cigarette and cigarillo smoking in time to smoke, number of puffs, and total puff volume (all P<0.001). Average puff duration, interpuff interval average puff volume, and puff velocity did not differ between cigarettes and cigarillos. Nicotine boost was similar after both cigarettes and cigarillos. COex boost was significantly greater after cigarillo smoking compared to cigarette smoking (P<0.001). The smoking pattern and exposure profile indicate that dual users inhale cigarillo smoke just as they inhale cigarette smoke thereby exposing themselves to considerable amounts of nicotine and other components of tobacco smoke. COex exposure results imply that cigarillo smoking may be associated with higher exposure to smoke-delivered volatile components of mainstream cigarillo smoke including carcinogens when compared to cigarettes. The findings that cigarillos and cigarettes are smoked similarly in dual users are relevant to health and regulatory considerations on cigar products. Copyright © 2015 Elsevier Inc. All rights reserved.

Effects of locus coeruleus stimulation on the responses of SI neurons of the rat to controlled natural and electrical stimulation of the skin.

PubMed

Snow, P J; Andre, P; Pompeiano, O

1999-02-01

1. The effects of microstimulation of the locus coeruleus (LC) region on the spontaneous discharge and the response of SI neurons to natural and electrical stimulation of the skin have been investigated in 26 urethane anesthetized Sprague-Dawley rats. In particular, one or two air puffs, 5-10 msec in duration, 1-2 psi, usually separated by an interval of 40 msec, were applied on the hairy skin of the wrist or the forepaw at the presentation rate of 1/sec. For units unresponsive to air puffs, similar presentation of low intensity electrical stimuli (0.2-5.0 V, 0.2-0.4 msec pulses) were applied through two needles inserted on the most effective area of the skin. Both natural and electrical stimulations of the skin were applied under control conditions, as well as 50 msec after a 250 msec train of 0.3 msec pulses at 40 Hz. 20-30 microA applied stereotaxically to the LC complex through a tungsten microelectrode. 2. Not all cortical units exhibited spontaneous discharge. Most of the units, however, which were spontaneously active, were inhibited by electrical stimulation of the LC complex, while the remaining ones were excited. The sites of stimulation, which included either the LC proper or the locus subcoeruleus, were identified following both anatomical and physiological criteria. 3. SI neurons recorded at sites between 400 and 950 microns below the surface of the cortex, thus being most likely granule cells of layers III and IV, responded to cutaneous stimuli with spikes which occurred with a latency of 20-30 msec in response to single air puffs and a latency of 15-20 msec in response to single electrical pulses to the skin. In both instances the response to the second stimulus applied at the interstimulus interval of 40 msec was markedly reduced or abolished due to postexcitatory inhibition following the response to the first stimulus (in-field inhibition). In contrast, units particularly located at or below 1000 microns from the cortical surface, which were of very large size probably corresponding to large layer V pyramidal cells, were often difficult to activate with air puffs applied at the centre of the receptive field (RF) and were submitted to electrical stimulation of the skin. 4. Among the 59 isolated SI units tested either to air puffs (45 neurons) or to electrical skin stimulation (14 neurons), 15 units (i.e., 25.4%) were facilitated, while 12 units (i.e., 20.3%) were inhibited following stimulation of the LC complex. 5. A marked feature of the facilitatory effects which usually involved the predominant response to the first air puff, but also the smaller response to the second puff, was that the increase in the number of spikes per stimulus was accompanied by a temporal focusing of the responses characterized by a clear tightening of the latency and narrowing of the peak of activity, which was often accompanied by some level of tonic inhibition of the background discharge. Thus, LC stimulation increased the signal-to-noise ratio of SI neuronal responses to skin stimulation. When inhibitory effects were induced by LC stimulation, they clearly affected the unit response to the first air puff, which was severely depressed. However, the response to the second puff could be facilitated, suggesting that LC stimulation might have produced inhibition of those inhibitory interneurons responsible for the postexcitatory inhibition of the units under examination. Evidence for spatial focusing of the response was not easily documented. In some units, however, LC stimulation produced either facilitation of the responses to puffs at the receptive field center and inhibition of the responses to puffs at the edge at the receptive field or vice versa. 6. Since the LC complex contains in the rat a predominant population of noradrenergic neurons, it is likely that the effects described above were mainly due to activation of these noradrenergic neurons. 7. (ABSTRACT TRUNCATED)

User's guide to the MESOI diffusion model and to the utility programs UPDATE and LOGRVU

DOE Office of Scientific and Technical Information (OSTI.GOV)

Athey, G.F.; Allwine, K.J.; Ramsdell, J.V.

MESOI is an interactive, Lagrangian puff trajectory diffusion model. The model is documented separately (Ramsdell and Athey, 1981); this report is intended to provide MESOI users with the information needed to successfully conduct model simulations. The user is also provided with guidance in the use of the data file maintenance and review programs; UPDATE and LOGRVU. Complete examples are given for the operaton of all three programs and an appendix documents UPDATE and LOGRVU.

Design and initial results from a kilojoule level Dense Plasma Focus with hollow anode and cylindrically symmetric gas puff.

PubMed

Ellsworth, J L; Falabella, S; Tang, V; Schmidt, A; Guethlein, G; Hawkins, S; Rusnak, B

2014-01-01

We have designed and built a Dense Plasma Focus (DPF) Z-pinch device using a kJ-level capacitor bank and a hollow anode, and fueled by a cylindrically symmetric gas puff. Using this device, we have measured peak deuteron beam energies of up to 400 keV at 0.8 kJ capacitor bank energy and pinch lengths of ∼6 mm, indicating accelerating fields greater than 50 MV/m. Neutron yields of on the order of 10(7) per shot were measured during deuterium operation. The cylindrical gas puff system permitted simultaneous operation of DPF with a radiofrequency quadrupole accelerator for beam-into-plasma experiments. This paper describes the machine design, the diagnostic systems, and our first results.

Turbulent structure and emissions of strongly-pulsed jet diffusion flames

NASA Astrophysics Data System (ADS)

Fregeau, Mathieu

This current research project studied the turbulent flame structure, the fuel/air mixing, the combustion characteristics of a nonpremixed pulsed (unsteady) and unpulsed (steady) flame configuration for both normal- and microgravity conditions, as well as the flame emissions in normal gravity. The unsteady flames were fully-modulated, with the fuel flow completely shut off between injection pulses using an externally controlled valve, resulting in the generation of compact puff-like flame structures. Conducting experiments in normal and microgravity environments enabled separate control over the relevant Richardson and Reynolds numbers to clarify the influence of buoyancy on the flame behavior, mixing, and structure. Experiments were performed in normal gravity in the laboratory at the University of Washington and in microgravity using the NASA GRC 2.2-second Drop Tower facility. High-speed imaging, as well as temperature and emissions probes were used to determine the large-scale structure dynamics, the details of the flame structure and oxidizer entrainment, the combustion temperatures, and the exhaust emissions of the pulsed and steady flames. Of particular interest was the impact of changes in flame structure due to pulsing on the combustion characteristics of this system. The turbulent flame puff celerity (i.e., the bulk velocity of the puffs) was strongly impacted by the jet-off time, increasing markedly as the time between pulses was decreased, which caused the degree of puff interaction to increase and the strongly-pulsed flame to more closely resemble a steady flame. This increase occurred for all values of injection time as well as for constant fuelling rate and in both the presence and absence of buoyancy. The removal of positive buoyancy in microgravity resulted in a decrease in the flame puff celerity in all cases, amounting to as much as 40%, for both constant jet injection velocity and constant fuelling rate. The mean flame length of the strongly-pulsed flames was not strongly impacted by buoyancy. This lack of sensitivity to buoyancy was consistent with offsetting changes in flame puff celerity and time to burnout for the microgravity versus normal-gravity cases. The emissions of CO and NO were examined in the vicinity of the visible flame tip and at the combustor exit for strongly-pulsed flames. The highest exhaust-point emission indices of CO for compact, isolated puffs were as much as a factor of six higher than those of elongated flames with longer injection times. The amount of CO decreased substantially with a decreased amount of flame puff interaction. The higher CO levels for pulsed flames with the shortest injection times were consistent with quenching due to the very rapid mixing and dilution with excess air for the most compact flame puffs. The injection time for which steady-flame emission levels were attained was comparable to the injection time for which the visible flame length approached the flame length of steady flames. The CO emissions, for a given fuelling rate, were strongly dependent on both the injection time and jet-off time for a jet-on fraction less than approximately 50%. The NO levels were generally proportional to the fuelling rate. This work indicates that there are specific combinations of injection time and jet-off time that considerably change the fuel/air mixing, resulting in emissions comparable to those of the steady flame while the flame length is significantly shorter. This points the potential utility of the strongly-pulsed injection technique in the development of compact, low emissions combustors involving turbulent diffusion flames. (Abstract shortened by UMI.)

Integrating a street-canyon model with a regional Gaussian dispersion model for improved characterisation of near-road air pollution

NASA Astrophysics Data System (ADS)

Fallah-Shorshani, Masoud; Shekarrizfard, Maryam; Hatzopoulou, Marianne

2017-03-01

The development and use of dispersion models that simulate traffic-related air pollution in urban areas has risen significantly in support of air pollution exposure research. In order to accurately estimate population exposure, it is important to generate concentration surfaces that take into account near-road concentrations as well as the transport of pollutants throughout an urban region. In this paper, an integrated modelling chain was developed to simulate ambient Nitrogen Dioxide (NO2) in a dense urban neighbourhood while taking into account traffic emissions, the regional background, and the transport of pollutants within the urban canopy. For this purpose, we developed a hybrid configuration including 1) a street canyon model, which simulates pollutant transfer along streets and intersections, taking into account the geometry of buildings and other obstacles, and 2) a Gaussian puff model, which resolves the transport of contaminants at the top of the urban canopy and accounts for regional meteorology. Each dispersion model was validated against measured concentrations and compared against the hybrid configuration. Our results demonstrate that the hybrid approach significantly improves the output of each model on its own. An underestimation appears clearly for the Gaussian model and street-canyon model compared to observed data. This is due to ignoring the building effect by the Gaussian model and undermining the contribution of other roads by the canyon model. The hybrid approach reduced the RMSE (of observed vs. predicted concentrations) by 16%-25% compared to each model on its own, and increased FAC2 (fraction of predictions within a factor of two of the observations) by 10%-34%.

Smoking Topography Characteristics of Very Low Nicotine Content Cigarettes, With and Without Nicotine Replacement, in Smokers With Schizophrenia and Controls

PubMed Central

Cassidy, Rachel N.; Miller, Mollie E.

2016-01-01

Introduction: Reducing the nicotine content of cigarettes to a minimally addictive level has been proposed as a regulatory strategy for reducing tobacco dependence. However, smokers with schizophrenia (SS) may be prone to changing their smoking topography in efforts to compensate for the reduction in nicotine content. The aims of this study were to compare smoking topography characteristics of usual-brand and very low nicotine content (VLNC) cigarettes in SS and control smokers without psychiatric illness (CS), and to determine whether nicotine replacement reversed any changes in topography produced by VLNC cigarettes. Methods: Using a within-subjects, counter-balanced design, SS (n = 27) and CS (n = 23) smoked usual brand cigarettes, VLNC cigarettes while wearing placebo patches (VLNC + PLA), or VLNC cigarettes while wearing transdermal nicotine patches totaling 42mg (VLNC + NIC) during 5-hour ad libitum smoking sessions. Cigarettes were smoked through topography measurement devices. Results: Across conditions, SS smoked more puffs per session and per cigarette, had higher cigarette volumes, and had shorter inter-puff intervals than CS (Ps < .01). During VLNC cigarette sessions, puff duration increased and time between puffs decreased, but participants smoked fewer puffs, resulting in a net decrease in cigarette and total session volume (Ps < .001). There were no significant interactions between group and condition. Conclusions: These findings indicate that acute use of VLNC cigarettes does not increase intensity of smoking in SS, and support the feasibility of a nicotine reduction policy. Implications: Reducing the nicotine in cigarettes to a minimally addictive level has been proposed as a means of reducing tobacco dependence. However, smokers, particularly those with schizophrenia (SS) may alter their puffing in an attempt to extract more nicotine from VLNC cigarettes. This study compared smoking topography of usual brand versus VLNC cigarettes, combined with placebo or transdermal nicotine patches, in SS and controls. Although some changes in topography were indicative of compensatory smoking, total puffs and total cigarette volume were reduced with VLNC cigarettes, indicating that acute VLNC cigarette use does not increase smoking in SS. PMID:26995794

Characterisation of the borgwaldt LM4E system for in vitro exposures to undiluted aerosols from next generation tobacco and nicotine products (NGPs).

PubMed

Adamson, Jason; Jaunky, Tomasz; Thorne, David; Gaça, Marianna D

2018-03-01

Traditional in vitro exposure to combustible tobacco products utilise exposure systems that include the use of smoking machines to generate, dilute and deliver smoke to in vitro cell cultures. With reported lower emissions from next generation tobacco and nicotine products (NGPs), including e-cigarettes and tobacco heating products (THPs), diluting the aerosol is potentially not required. Herein we present a simplified exposure scenario to undiluted NGP aerosols, using a new puffing system called the LM4E. Nicotine delivery from an e-cigarette was used as a dosimetry marker, and was measured at source across 4 LM4E ports and in the exposure chamber. Cell viability studies, using Neutral Red Uptake (NRU) assay, were performed using H292 human lung epithelial cells, testing undiluted aerosols from an e-cigarette and a THP. E-cigarette mean nicotine generated at source was measured at 0.084 ± 0.005 mg/puff with no significant differences in delivery across the 4 different ports, p = 0.268 (n = 10/port). Mean nicotine delivery from the e-cigarette to the in vitro exposure chamber (measured up to 100 puffs) was 0.046 ± 0.006 mg/puff, p = 0.061. Aerosol penetration within the LM4E was 55% from source to chamber. H292 cells were exposed to undiluted e-cigarette aerosol for 2 h (240 puffs) or undiluted THP aerosol for 1 h (120 puffs). There were positive correlations between puff number and nicotine in the exposed culture media, R 2  = 0.764 for the e-cigarette and R 2  = 0.970 for the THP. NRU determined cell viability for e-cigarettes after 2 h' exposure resulted in 21.5 ± 17.0% cell survival, however for the THP, full cytotoxicity was reached after 1-h exposure. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Efficient generation of fast neutrons by magnetized deuterons in an optimized deuterium gas-puff z-pinch

NASA Astrophysics Data System (ADS)

Klir, D.; Shishlov, A. V.; Kokshenev, V. A.; Kubes, P.; Labetsky, A. Yu; Rezac, K.; Cherdizov, R. K.; Cikhardt, J.; Cikhardtova, B.; Dudkin, G. N.; Fursov, F. I.; Garapatsky, A. A.; Kovalchuk, B. M.; Kravarik, J.; Kurmaev, N. E.; Orcikova, H.; Padalko, V. N.; Ratakhin, N. A.; Sila, O.; Turek, K.; Varlachev, V. A.

2015-04-01

Z-pinch experiments with deuterium gas puffs have been carried out on the GIT-12 generator at 3 MA currents. Recently, a novel configuration of a deuterium gas-puff z-pinch was used to accelerate deuterons and to generate fast neutrons. In order to form a homogeneous, uniformly conducting layer at a large initial radius, an inner deuterium gas puff was surrounded by an outer hollow cylindrical plasma shell. The plasma shell consisting of hydrogen and carbon ions was formed at the diameter of 350 mm by 48 plasma guns. A linear mass of the plasma shell was about 5 µg cm-1 whereas a total linear mass of deuterium gas in single or double shell gas puffs was about 100 µg cm-1. The implosion lasted 700 ns and seemed to be stable up to a 5 mm radius. During stagnation, m = 0 instabilities became more pronounced. When a disruption of necks occurred, the plasma impedance reached 0.4 Ω and high energy (>2 MeV) bremsstrahlung radiation together with high energy deuterons were produced. Maximum neutron energies of 33 MeV were observed by axial time-of-flight detectors. The observed neutron spectra could be explained by a suprathermal distribution of deuterons with a high energy tail f≤ft({{E}\\text{d}}\\right)\\propto E\\text{d}-(1.8+/- 0.2) . Neutron yields reached 3.6 × 1012 at a 2.7 MA current. A high neutron production efficiency of 6 × 107 neutrons per one joule of plasma energy resulted from the generation of high energy deuterons and from their magnetization inside plasmas.

Aldehyde levels in e-cigarette aerosol: Findings from a replication study and from use of a new-generation device.

PubMed

Farsalinos, Konstantinos E; Kistler, Kurt A; Pennington, Alexander; Spyrou, Alketa; Kouretas, Dimitris; Gillman, Gene

2018-01-01

A recent study identified high aldehyde emissions from e-cigarettes (ECs), that when converted to reasonable daily human EC liquid consumption, 5 g/day, gave formaldehyde exposure equivalent to 604-3257 tobacco cigarettes. We replicated this study and also tested a new-generation atomizer under verified realistic (no dry puff) conditions. CE4v2 atomizers were tested at 3.8 V and 4.8 V, and a Nautilus Mini atomizer was tested at 9.0 W and 13.5 W. All measurements were performed in a laboratory ISO-accredited for EC aerosol collection and aldehyde measurements. CE4v2 generated dry puffs at both voltage settings. Formaldehyde levels were >10-fold lower, acetaldehyde 6-9-fold lower and acrolein 16-26-fold lower than reported in the previous study. Nautilus Mini did not generate dry puffs, and minimal aldehydes were emitted despite >100% higher aerosol production per puff compared to CE4v2 (formaldehyde: 16.7 and 16.5 μg/g; acetaldehyde: 9.6 and 10.3 μg/g; acrolein: 8.6 and 11.7 μg/g at 9.0 W and 13.5 W, respectively). EC liquid consumption of 5 g/day reduces aldehyde exposure by 94.4-99.8% compared to smoking 20 tobacco cigarettes. Checking for dry puffs is essential for EC emission testing. Under realistic conditions, new-generation ECs emit minimal aldehydes/g liquid at both low and high power. Validated methods should be used when analyzing EC aerosol. Copyright © 2017 Elsevier Ltd. All rights reserved.

CO exposure, puff topography, and subjective effects in waterpipe tobacco smokers

PubMed Central

Maziak, Wasim; Rastam, Samer; Ibrahim, Iman; Ward, Kenneth D.; Shihadeh, Alan

2009-01-01

Introduction: Waterpipe tobacco smoking is increasing in popularity though the toxicant exposure and effects associated with this tobacco use method are not well understood. Methods: Sixty-one waterpipe tobacco smokers (56 males; mean age ± SD, 30.9 ± 9.5 years; mean number of weekly waterpipe smoking episodes, 7.8 ± 5.7; mean duration of waterpipe smoking 8.5 ± 6.1 years) abstained from smoking for at least 24 hr and then smoked tobacco from a waterpipe ad libitum in a laboratory. Before and after smoking, expired-air carbon monoxide (CO) and subjective effects were assessed; puff topography was measured during smoking. Results: The mean waterpipe use episode duration was 33.1 ± 13.1 min. Expired-air CO increased significantly from a mean of 4.0 ± 1.7 before to 35.5 ± 32.7 after smoking. On average, participants took 169 ± 100 puffs, with a mean puff volume of 511 ± 333 ml. Urge to smoke, restlessness, craving, and other tobacco abstinence symptoms were reduced significantly after smoking, while ratings of dizzy, lightheaded, and other direct effects of nicotine increased. Discussion: Expired-air CO and puff topography data indicate that, relative to a single cigarette, a single waterpipe tobacco smoking episode is associated with greater smoke exposure. Abstinent waterpipe tobacco smokers report symptoms similar to those reported by abstinent cigarette smokers, and these symptoms are reduced by subsequent waterpipe tobacco smoking. Taken together, these data are consistent with the notion that waterpipe tobacco smoking is likely associated with the risk of tobacco/nicotine dependence. PMID:19420278

Characterization of neutron emission from mega-ampere deuterium gas puff Z-pinch at microsecond implosion times

NASA Astrophysics Data System (ADS)

Klir, D.; Shishlov, A. V.; Kokshenev, V. A.; Kubes, P.; Labetsky, A. Yu; Rezac, K.; Cikhardt, J.; Fursov, F. I.; Kovalchuk, B. M.; Kravarik, J.; Kurmaev, N. E.; Ratakhin, N. A.; Sila, O.; Stodulka, J.

2013-08-01

Experiments with deuterium (D2) triple shell gas puffs were carried out on the GIT-12 generator at a 3 MA current level and microsecond implosion times. The outer, middle and inner nozzle diameters were 160 mm, 80 mm and 30 mm, respectively. The influence of the mass of deuterium shells on neutron emission times, neutron yields and neutron energy spectra was studied. The injected linear mass of deuterium varied between 50 and 255 µg cm-1. Gas puffs imploded onto the axis before the peak of generator current at 700-1100 ns. Most of the neutrons were emitted during the second neutron pulse after the development of instabilities. Despite higher currents, heavier gas puffs produced lower neutron yields. Optimal mass and a short time delay between the valve opening and the generator triggering were more important than the better coincidence of stagnation with peak current. The peak neutron yield from D(d, n)3He reactions reached 3 × 1011 at 2.8 MA current, 90 µg cm-1 injected linear mass and 37 mm anode-cathode gap. In the case of lower mass shots, a large number of 10 MeV neutrons were produced either by secondary DT reactions or by DD reactions of deuterons with energies above 7 MeV. The average neutron yield ratio Y>10 MeV/Y2.5 MeV reached (6 ± 3) × 10-4. Such a result can be explained by a power law distribution for deuterons as \\rmd N_d/\\rmd E_d\\propto E_d^{-3} . The optimization of a D2 gas puff Z-pinch and similarities to a plasma focus and its drive parameter are described.

Wide band laser-plasma soft X-ray source using a gas puff target for direct photo-etching of polymers

NASA Astrophysics Data System (ADS)

Bartnik, Andrzej; Fiedorowicz, Henryk; Jarocki, Roman; Kostecki, Jerzy; Rakowski, Rafał; Szczurek, Mirosław

2005-09-01

Organic polymers (PMMA, PTFE, PET, and PI) are considered as the important materials in microengineering, especially for biological and medical applications. Micromachining of such materials is possible with the use of different techniques that involve electromagnetic radiation or charged particle beams. Another possibility of high aspect ratio micromachining of PTFE is direct photo-etching using synchrotron radiation. X-ray and ultraviolet radiation from other sources, for micromachining of materials by direct photo-etching can be also applied. In this paper we present the results of investigation of a wide band soft X-ray source and its application for direct photo-etching of organic polymers. X-ray radiation in the wavelength range from about 3 nm to 20 nm was produced as a result of irradiation of a double-stream gas puff target with laser pulses of energy 0.8 J and time duration of about 3 ns. The spectra, plasma size and absolute energies of soft X-ray pulses for different gas puff targets were measured. Photo-etching process of polymers irradiated with the use of the soft X-ray radiation was analyzed and investigated. Samples of organic polymers were placed inside a vacuum chamber of the x-ray source, close to the gas puff target at the distance of about 2 cm from plasmas created by focused laser pulses. A fine metal grid placed in front of the samples was used as a mask to form structures by x-ray ablation. The results of photo-etching process for several minutes exposition with l0Hz repetition rate were presented. High ablation efficiency was obtained with the use of the gas puff target containing xenon surrounded by helium.

Relationship between negative affect and smoking topography in heavy drinking smokers.

PubMed

Green, ReJoyce; Bujarski, Spencer; Roche, Daniel J O; Ray, Lara A

2016-10-01

Heavy drinking smokers represent a sizeable subgroup of smokers for whom nicotine deprivation and alcohol use increases the urge to smoke in the laboratory and predicts lapses during smoking cessation. The manner in which individuals smoke a cigarette (i.e. smoking topography) provides a reliable index of smoking intensity and reinforcement, yet the effects of affect on smoking topography have not been thoroughly examined in heavy drinking smokers. The current study examined how affect and nicotine deprivation predict smoking behavior as participants (N=27) smoked one cigarette using a smoking topography device after 12-h of nicotine abstinence and after a priming dose of alcohol (target BrAC=0.06g/dl). Primary smoking topography measures were puff volume, velocity, duration, and inter-puff interval (IPI). The effect of nicotine deprivation was measured by the Minnesota Nicotine Withdrawal Scale (MNWS) and the Profile of Mood States (POMS). Measures were obtained at baseline (i.e. 12-h of nicotine abstinence and pre-alcohol) and 30-minutes after alcohol administration (i.e. peak BrAC). Results revealed post-priming negative affect significantly moderated the trajectories of puff volume, puff duration and IPI (p's<0.05) over the course of the cigarette, such that those with greater negative affect had flatter slopes for volume and duration and increasingly infrequent puffs. Our results suggest that baseline and post-priming negative affect following nicotine deprivation alters smoking patterns and increases nicotine exposure throughout a single cigarette. Future studies need to examine differential amounts of nicotine deprivation on response to alcohol and smoking in heavy drinking smokers. Copyright © 2016 Elsevier Ltd. All rights reserved.

Umbral oscillations and penumbral waves in H alpha. [in sunspots

NASA Technical Reports Server (NTRS)

Moore, R. L.; Tang, F.

1975-01-01

Examples are presented of umbral oscillations observed on Big Bear H-alpha filtergram movies, and the relation between umbral oscillations and running penumbral waves occurring in the same sunspot is investigated. Umbral oscillations near the center of the umbra are probably physically independent of the penumbral waves because the period of these umbral oscillations (150 sec) is shorter than the penumbral wave period (270 sec), but not a harmonic. Dark puffs emerge from the edge of the umbra and move outward across the penumbra, and have the same period as the running penumbral waves. These dark puffs are interpreted to be the extension of chromospheric umbral oscillations at the edge of the umbra. It is suggested that the dark puffs and the running penumbral waves have a common source: photospheric oscillations just inside the umbra.

Demonstration of a neonlike argon soft-x-ray laser with a picosecond-laser-irradiated gas puff target.

PubMed

Fiedorowicz, H; Bartnik, A; Dunn, J; Smith, R F; Hunter, J; Nilsen, J; Osterheld, A L; Shlyaptsev, V N

2001-09-15

We demonstrate a neonlike argon-ion x-ray laser, using a short-pulse laser-irradiated gas puff target. The gas puff target was formed by pulsed injection of gas from a high-pressure solenoid valve through a nozzle in the form of a narrow slit and irradiated with a combination of long, 600-ps and short, 6-ps high-power laser pulses with a total of 10 J of energy in a traveling-wave excitation scheme. Lasing was observed on the 3p (1)S(0)?3s (1)P(1) transition at 46.9 nm and the 3d (1)P(1)?3p (1)P(1) transition at 45.1 nm. A gain of 11 cm(-1) was measured on these transitions for targets up to 0.9 cm long.

Application of the Approximate Bayesian Computation methods in the stochastic estimation of atmospheric contamination parameters for mobile sources

NASA Astrophysics Data System (ADS)

Kopka, Piotr; Wawrzynczak, Anna; Borysiewicz, Mieczyslaw

2016-11-01

In this paper the Bayesian methodology, known as Approximate Bayesian Computation (ABC), is applied to the problem of the atmospheric contamination source identification. The algorithm input data are on-line arriving concentrations of the released substance registered by the distributed sensors network. This paper presents the Sequential ABC algorithm in detail and tests its efficiency in estimation of probabilistic distributions of atmospheric release parameters of a mobile contamination source. The developed algorithms are tested using the data from Over-Land Atmospheric Diffusion (OLAD) field tracer experiment. The paper demonstrates estimation of seven parameters characterizing the contamination source, i.e.: contamination source starting position (x,y), the direction of the motion of the source (d), its velocity (v), release rate (q), start time of release (ts) and its duration (td). The online-arriving new concentrations dynamically update the probability distributions of search parameters. The atmospheric dispersion Second-order Closure Integrated PUFF (SCIPUFF) Model is used as the forward model to predict the concentrations at the sensors locations.

Fugitive Dust Emission Factors for Puff and Mobile Military Sources Measured by Micro-pulse Lidar - A Summary of Results

NASA Astrophysics Data System (ADS)

Yuen, W.; Du, K.; Rood, M. J.; Kemme, M. R.; Kim, B.; Hashmonay, R. A.

2010-12-01

A summary of the development of a novel optical remote sensing (ORS) method that determined fugitive dust emission factors for unique military activities is described for puff and mobile sources. Four field campaigns characterized artillery back blasts as puff sources (M549A1 and M107), and movement of military vehicles (M1A1, M113, Bradley Fighting Vehicle (BFV), M88, M270, M577, and HEMTT) and an airborne helicopter (Bell 210) as mobile sources. The ORS method includes a Micro-Pulse Lidar (MPL) and a reflective target that determines one-dimensional (1-D) light extinction coefficient profiles. The MPL was mounted on a positioner that allows the MPL to automatically scan vertically, which allowed 1-D extinction coefficient profiles to be measured at select angles from horizontal. Two-dimensional (2-D) light extinction coefficient profiles were then determined by interpolating the 1-D extinction profiles measured at select angles. Dust property, in the form of the mass extinction efficiency (MEE), was measured using Open Path- Fourier Transform Infrared Spectrometry (OP-FTIR) and Open Path- Laser Transmissometry (OP-LT) in the first three field campaigns and an OP-LT and DustTrak™ in the fourth field campaign. MEE was used to convert the 2-D light extinction coefficient profiles to 2-D dust mass concentration profiles. Emission factors were determined by integrating the 2-D mass concentration profiles with measured wind vectors. Results from these field campaigns show that: 1) artillery with stronger recoiling forces generates more fugitive dust; 2) the dust emission factors for tracked vehicles are correlated with vehicle momentum; 3) emission factor decreases with increasing speed for airborne helicopters; and 4) wheeled vehicles (HEMTT) generate more fugitive dust than tracked vehicles (M88, M270, M577).

Synaptic Activity in Serotonergic Neurons Is Required for Air-Puff Stimulated Flight in Drosophila melanogaster

PubMed Central

Sadaf, Sufia; Birman, Serge; Hasan, Gaiti

2012-01-01

Background Flight is an integral component of many complex behavioral patterns in insects. The giant fiber circuit has been well studied in several insects including Drosophila. However, components of the insect flight circuit that respond to an air-puff stimulus and comprise the flight central pattern generator are poorly defined. Aminergic neurons have been implicated in locust, moth and Drosophila flight. Here we have investigated the requirement of neuronal activity in serotonergic neurons, during development and in adults, on air-puff induced flight in Drosophila. Methodology/Principal Findings To target serotonergic neurons specifically, a Drosophila strain that contains regulatory regions from the TRH (Tryptophan Hydroxylase) gene linked to the yeast transcription factor GAL4 was used. By blocking synaptic transmission from serotonergic neurons with a tetanus toxin transgene or by hyperpolarisation with Kir2.1, close to 50% adults became flightless. Temporal expression of a temperature sensitive Dynamin mutant transgene (Shits) suggests that synaptic function in serotonergic neurons is required both during development and in adults. Depletion of IP3R in serotonergic neurons via RNAi did not affect flight. Interestingly, at all stages a partial requirement for synaptic activity in serotonergic neurons was observed. The status of serotonergic neurons was investigated in the central nervous system of larvae and adults expressing tetanus toxin. A small but significant reduction was observed in serotonergic cell number in adult second thoracic segments from flightless tetanus toxin expressing animals. Conclusions These studies show that loss of synaptic activity in serotonergic neurons causes a flight deficit. The temporal focus of the flight deficit is during pupal development and in adults. The cause of the flight deficit is likely to be loss of neurons and reduced synaptic function. Based on the partial phenotypes, serotonergic neurons appear to be modulatory, rather than an intrinsic part of the flight circuit. PMID:23029511

Hedonic Predictors of Tobacco Dependence: A Puff Guide to Smoking Cessation

DTIC Science & Technology

2015-04-07

process may not always be the case. While Perkins et al. (31) showed the potential for a connection between puff volume, considered reinforcement...effect can be attributed to the effects of "acute tolerance" (31 ). Nicotine is thought to acutely desensitize nicotinic receptors ("acute tolerance...company that performs biological assays) for the cotinine assay. Salivary cotinine levels were measured through an enzyme immunoassay conducted by

Marihuana-induced embryotoxicity in the rabbit.

PubMed

Rosenkrantz, H; Grant, R J; Fleischman, R W; Baker, J R

1986-08-01

Few teratogenic studies in animals have been performed simulating marihuana smoking in man. An inhalation marihuana teratology study was conducted in albino rabbits utilizing a modified automatic smoking machine originally developed for rats and mice. Appropriate numbers of dams were exposed to 4 puffs (0.14 mg/kg), 8 puffs (0.72 mg/kg), or 16 puffs (1.44 mg/kg) once daily during gestation Days 6 to 18, and sacrificed on Day 28. Control dams were exposed to 12 puffs of placebo cigarettes or sham-treated for a similar duration in the absence of any smoke. Consistency of smoke was monitored by cigarette weights, total particulate matter, concentrations of carbon monoxide (CO), and tetrahydrocannibinol (THC) in smoke, carboxyhemoglobin levels, and plasma THC levels. Except for a transient decrease in dam respiration rates, other gross toxic signs were absent. Reproductive parameters of mothers were generally normal except for a dose-related embryotoxicity predominantly associated with early resorptions. Despite twice the number of embryo/fetal deaths, there were no marihuana soft tissue or skeletal defects. A correlation between dam demises and CO levels among placebo-exposed animals was related to greater quantities of CO being generated during placebo combustion. It has been shown in the rabbit that marihuana is embryotoxic and not a teratogen at plasma THC levels found in human females.

Acceptability and characterization of extruded pinto, navy and black beans.

PubMed

Simons, Courtney W; Hall, Clifford; Tulbek, Mehmet; Mendis, Mihiri; Heck, Taylor; Ogunyemi, Samuel

2015-08-30

Consumption of dry beans has been relatively flat over the last decade. Creating new bean products may increase the consumption of beans and allow more consumers to obtain the health benefits of beans. In this study, pinto, navy and black beans were milled and the resulting flours extruded into puffs. Unflavored extruded puffs were evaluated by untrained panelists using a hedonic scale for appearance, flavor, texture and overall acceptability. The compositions of raw flours and extrudates were characterized. Sensory results indicated that all beans met or exceeded the minimum requirement for acceptability. Overall acceptability of navy and pinto beans was not significantly different, while acceptability of black bean puffs was significantly lower. Total protein (198-217 g kg(-1)) in extrudates was significantly different among the three beans. Total starch ranged from 398 to 406 g kg(-1) and was not significantly different. Resistant starch, total extractable lipid and raffinose contents were significantly reduced by extrusion. Extrusion did not affect crude fiber and phytic acid contents. The minimal effects on protein and fiber contents, the significant reduction in raffinose content and the acceptability of the unflavored extruded puffs support using various bean flours as ingredients in extruded puffed products. © 2014 Society of Chemical Industry.

Gorilla Mothers Also Matter! New Insights on Social Transmission in Gorillas (Gorilla gorilla gorilla) in Captivity

PubMed Central

Luef, Eva Maria; Pika, Simone

2013-01-01

The present paper describes two distinct behaviors relating to food processing and communication that were observed in a community of five separately housed groups of lowland gorillas (Gorilla gorilla gorilla) in captivity during two study periods one decade apart: (1) a food processing technique to separate wheat from chaff, the so-called puff-blowing technique; and (2) a male display used to attract the attention of visitors, the so-called throw-kiss-display. We investigated (a) whether the behaviors were transmitted within the respective groups; and if yes, (b) their possible mode of transmission. Our results showed that only the food processing technique spread from three to twenty-one individuals during the ten-year period, whereas the communicative display died out completely. The main transmission mode of the puff-blowing technique was the mother-offspring dyad: offspring of puff-blowing mothers showed the behavior, while the offspring of non- puff-blowing mothers did not. These results strongly support the role mothers play in the acquisition of novel skills and vertical social transmission. Furthermore, they suggest that behaviors, which provide a direct benefit to individuals, have a high chance of social transmission while the loss of benefits can result in the extinction of behaviors. PMID:24312184

Gorilla mothers also matter! New insights on social transmission in gorillas (Gorilla gorilla gorilla) in captivity.

PubMed

Luef, Eva Maria; Pika, Simone

2013-01-01

The present paper describes two distinct behaviors relating to food processing and communication that were observed in a community of five separately housed groups of lowland gorillas (Gorilla gorilla gorilla) in captivity during two study periods one decade apart: (1) a food processing technique to separate wheat from chaff, the so-called puff-blowing technique; and (2) a male display used to attract the attention of visitors, the so-called throw-kiss-display. We investigated (a) whether the behaviors were transmitted within the respective groups; and if yes, (b) their possible mode of transmission. Our results showed that only the food processing technique spread from three to twenty-one individuals during the ten-year period, whereas the communicative display died out completely. The main transmission mode of the puff-blowing technique was the mother-offspring dyad: offspring of puff-blowing mothers showed the behavior, while the offspring of non- puff-blowing mothers did not. These results strongly support the role mothers play in the acquisition of novel skills and vertical social transmission. Furthermore, they suggest that behaviors, which provide a direct benefit to individuals, have a high chance of social transmission while the loss of benefits can result in the extinction of behaviors.

Flame Structure and Emissions of Strongly-Pulsed Turbulent Diffusion Flames with Swirl

NASA Astrophysics Data System (ADS)

Liao, Ying-Hao

This work studies the turbulent flame structure, the reaction-zone structure and the exhaust emissions of strongly-pulsed, non-premixed flames with co-flow swirl. The fuel injection is controlled by strongly-pulsing the fuel flow by a fast-response solenoid valve such that the fuel flow is completely shut off between pulses. This control strategy allows the fuel injection to be controlled over a wide range of operating conditions, allowing the flame structure to range from isolated fully-modulated puffs to interacting puffs to steady flames. The swirl level is controlled by varying the ratio of the volumetric flow rate of the tangential air to that of the axial air. For strongly-pulsed flames, both with and without swirl, the flame geometry is strongly impacted by the injection time. Flames appear to exhibit compact, puff-like structures for short injection times, while elongated flames, similar in behaviors to steady flames, occur for long injection times. The flames with swirl are found to be shorter for the same fuel injection conditions. The separation/interaction level between flame puffs in these flames is essentially governed by the jet-off time. The separation between flame puffs decreases as swirl is imposed, consistent with the decrease in flame puff celerity due to swirl. The decreased flame length and flame puff celerity are consistent with an increased rate of air entrainment due to swirl. The highest levels of CO emissions are generally found for compact, isolated flame puffs, consistent with the rapid quenching due to rapid dilution with excess air. The imposition of swirl generally results in a decrease in CO levels, suggesting more rapid and complete fuel/air mixing by imposing swirl in the co-flow stream. The levels of NO emissions for most cases are generally below the steady-flame value. The NO levels become comparable to the steady-flame value for sufficiently short jet-off time. The swirled co-flow air can, in some cases, increase the NO emissions. The elevated NO emissions are due to a longer combustion residence time due to the flow recirculation within the swirl-induced recirculation zone. The reaction zone structure, based on OH planar laser-induced fluorescence (PLIF) is broadly consistent with the observation of luminous flame structure for these types of flames. In many cases, the reaction zone exhibits discontinuities at the instantaneous flame tip in the early period of fuel injection. These discontinuities in the reaction zone likely result from the non-ignition of injected fuel, due to a relatively slower reaction rate in comparison with the mixing rate. The discontinuity in the OH zone is generally seen to diminish with increased swirl level. Statistics generated from the OH PLIF signals show that the reaction zone area generally increases with increased swirl level, consistent with a broader and more convoluted OH-zone structure for flames with swirl. The reaction zone area for swirled flames generally exhibits a higher degree of fluctuation, suggesting a relatively stronger impact of flow turbulence on the flame structure for flames with swirl.

Intermittent fluctuations in the Alcator C-Mod scrape-off layer for ohmic and high confinement mode plasmas

NASA Astrophysics Data System (ADS)

Garcia, O. E.; Kube, R.; Theodorsen, A.; LaBombard, B.; Terry, J. L.

2018-05-01

Plasma fluctuations in the scrape-off layer of the Alcator C-Mod tokamak in ohmic and high confinement modes have been analyzed using gas puff imaging data. In all cases investigated, the time series of emission from a single spatially resolved view into the gas puff are dominated by large-amplitude bursts, attributed to blob-like filament structures moving radially outwards and poloidally. There is a remarkable similarity of the fluctuation statistics in ohmic plasmas and in edge localized mode-free and enhanced D-alpha high confinement mode plasmas. Conditionally averaged waveforms have a two-sided exponential shape with comparable temporal scales and asymmetry, while the burst amplitudes and the waiting times between them are exponentially distributed. The probability density functions and the frequency power spectral densities are similar for all these confinement modes. These results provide strong evidence in support of a stochastic model describing the plasma fluctuations in the scrape-off layer as a super-position of uncorrelated exponential pulses. Predictions of this model are in excellent agreement with experimental measurements in both ohmic and high confinement mode plasmas. The stochastic model thus provides a valuable tool for predicting fluctuation-induced plasma-wall interactions in magnetically confined fusion plasmas.

The Supercritical CO2 Huff-n-puff Experiment of Shale Oil Utilizing Isopropanol

NASA Astrophysics Data System (ADS)

Shang, Shengxiang; Dong, Mingzhe; Gong, Houjian

2018-01-01

In this study, the supercritical CO2 huff-n-puff experiment of shale oil has been investigated. Experimental data shows that the addition of isopropanol can greatly improve the recovery of shale oil. And this provides a new way to improve the recovery of shale oil. In this paper, it is also tried to analyze the influencing factor of isopropanol on the recovery of shale oil by analyzing the MMP.

Experimental research of neutron yield and spectrum from deuterium gas-puff z-pinch on the GIT-12 generator at current above 2 MA

NASA Astrophysics Data System (ADS)

Cherdizov, R. K.; Fursov, F. I.; Kokshenev, V. A.; Kurmaev, N. E.; Labetsky, A. Yu; Ratakhin, N. A.; Shishlov, A. V.; Cikhardt, J.; Cikhardtova, B.; Klir, D.; Kravarik, J.; Kubes, P.; Rezac, K.; Dudkin, G. N.; Garapatsky, A. A.; Padalko, V. N.; Varlachev, V. A.

2017-05-01

The Z-pinch experiments with deuterium gas-puff surrounded by an outer plasma shell were carried out on the GIT-12 generator (Tomsk, Russia) at currents of 2 MA. The plasma shell consisting of hydrogen and carbon ions was formed by 48 plasma guns. The deuterium gas-puff was created by a fast electromagnetic valve. This configuration provides an efficient mode of the neutron production in DD reaction, and the neutron yield reaches a value above 1012 neutrons per shot. Neutron diagnostics included scintillation TOF detectors for determination of the neutron energy spectrum, bubble detectors BD-PND, a silver activation detector, and several activation samples for determination of the neutron yield analysed by a Sodium Iodide (NaI) and a high-purity Germanium (HPGe) detectors. Using this neutron diagnostic complex, we measured the total neutron yield and amount of high-energy neutrons.

Smoking Topography Characteristics of Very Low Nicotine Content Cigarettes, With and Without Nicotine Replacement, in Smokers With Schizophrenia and Controls.

PubMed

Tidey, Jennifer W; Cassidy, Rachel N; Miller, Mollie E

2016-09-01

Reducing the nicotine content of cigarettes to a minimally addictive level has been proposed as a regulatory strategy for reducing tobacco dependence. However, smokers with schizophrenia (SS) may be prone to changing their smoking topography in efforts to compensate for the reduction in nicotine content. The aims of this study were to compare smoking topography characteristics of usual-brand and very low nicotine content (VLNC) cigarettes in SS and control smokers without psychiatric illness (CS), and to determine whether nicotine replacement reversed any changes in topography produced by VLNC cigarettes. Using a within-subjects, counter-balanced design, SS (n = 27) and CS (n = 23) smoked usual brand cigarettes, VLNC cigarettes while wearing placebo patches (VLNC + PLA), or VLNC cigarettes while wearing transdermal nicotine patches totaling 42mg (VLNC + NIC) during 5-hour ad libitum smoking sessions. Cigarettes were smoked through topography measurement devices. Across conditions, SS smoked more puffs per session and per cigarette, had higher cigarette volumes, and had shorter inter-puff intervals than CS (Ps < .01). During VLNC cigarette sessions, puff duration increased and time between puffs decreased, but participants smoked fewer puffs, resulting in a net decrease in cigarette and total session volume (Ps < .001). There were no significant interactions between group and condition. These findings indicate that acute use of VLNC cigarettes does not increase intensity of smoking in SS, and support the feasibility of a nicotine reduction policy. Reducing the nicotine in cigarettes to a minimally addictive level has been proposed as a means of reducing tobacco dependence. However, smokers, particularly those with schizophrenia (SS) may alter their puffing in an attempt to extract more nicotine from VLNC cigarettes. This study compared smoking topography of usual brand versus VLNC cigarettes, combined with placebo or transdermal nicotine patches, in SS and controls. Although some changes in topography were indicative of compensatory smoking, total puffs and total cigarette volume were reduced with VLNC cigarettes, indicating that acute VLNC cigarette use does not increase smoking in SS. © The Author 2016. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Evaluation of regional and local atmospheric dispersion models for the analysis of traffic-related air pollution in urban areas

NASA Astrophysics Data System (ADS)

Fallah-Shorshani, Masoud; Shekarrizfard, Maryam; Hatzopoulou, Marianne

2017-10-01

Dispersion of road transport emissions in urban metropolitan areas is typically simulated using Gaussian models that ignore the turbulence and drag induced by buildings, which are especially relevant for areas with dense downtown cores. To consider the effect of buildings, street canyon models are used but often at the level of single urban corridors and small road networks. In this paper, we compare and validate two dispersion models with widely varying algorithms, across a modelling domain consisting of the City of Montreal, Canada accounting for emissions of more 40,000 roads. The first dispersion model is based on flow decomposition into the urban canopy sub-flow as well as overlying airflow. It takes into account the specific height and geometry of buildings along each road. The second model is a Gaussian puff dispersion model, which handles complex terrain and incorporates three-dimensional meteorology, but accounts for buildings only through variations in the initial vertical mixing coefficient. Validation against surface observations indicated that both models under-predicted measured concentrations. Average weekly exposure surfaces derived from both models were found to be reasonably correlated (r = 0.8) although the Gaussian dispersion model tended to underestimate concentrations around the roadways compared to the street canyon model. In addition, both models were used to estimate exposures of a representative sample of the Montreal population composed of 1319 individuals. Large differences were noted whereby exposures derived from the Gaussian puff model were significantly lower than exposures derived from the street canyon model, an expected result considering the concentration of population around roadways. These differences have large implications for the analyses of health effects associated with NO2 exposure.

Simulations of Ar gas-puff Z-pinch radiation sources with double shells and central jets on the Z generator

DOE PAGES

Tangri, V.; Harvey-Thompson, Adam James; Giuliani, J. L.; ...

2016-10-19

Radiation-magnetohydrodynamic simulations using the non-LTE Mach2-TCRE code in (r,z) geometry are performed for two pairs of recent Ar gas-puff Z-pinch experiments on the refurbished Z generator with an 8 cm diameter nozzle. One pair of shots had an outer-to-inner shell mass ratio of 1:1.6 and a second pair had a ratio of 1:1.

Development, validation and application of a device to measure e-cigarette users’ puffing topography

PubMed Central

Cunningham, Anthony; Slayford, Sandra; Vas, Carl; Gee, Jodie; Costigan, Sandra; Prasad, Krishna

2016-01-01

With the rapidly rising popularity and substantial evolution of electronic cigarettes (e-cigarettes) in the past 5–6 years, how these devices are used by vapers and consumers’ exposure to aerosol emissions need to be understood. We used puffing topography to measure directly product use. We adapted a cigarette puffing topography device for use with e-cigarettes. We performed validation using air and e-cigarette aerosol under multiple regimes. Consumer puffing topography was measured for 60 vapers provided with rechargeable “cig-a-like” or larger button-activated e-cigarettes, to use ad-libitum in two sessions. Under all regimes, air puff volumes were within 1 mL of the target and aerosol volumes within 5 mL for all device types, serving to validate the device. Vapers’ mean puff durations (2.0 s and 2.2 s) were similar with both types of e-cigarette, but mean puff volumes (52.2 mL and 83.0 mL) and mean inter-puff intervals (23.2 s and 29.3 s) differed significantly. The differing data show that product characteristics influence puffing topography and, therefore, the results obtained from a given e-cigarette might not read across to other products. Understanding the factors that affect puffing topography will be important for standardising testing protocols for e-cigarette emissions. PMID:27721496

Impact of neutral density fluctuations on gas puff imaging diagnostics

NASA Astrophysics Data System (ADS)

Wersal, C.; Ricci, P.

2017-11-01

A three-dimensional turbulence simulation of the SOL and edge regions of a toroidally limited tokamak is carried out. The simulation couples self-consistently the drift-reduced two-fluid Braginskii equations to a kinetic equation for neutral atoms. A diagnostic neutral gas puff on the low-field side midplane is included and the impact of neutral density fluctuations on D_α light emission investigated. We find that neutral density fluctuations affect the D_α emission. In particular, at a radial distance from the gas puff smaller than the neutral mean free path, neutral density fluctuations are anti-correlated with plasma density, electron temperature, and D_α fluctuations. It follows that the neutral fluctuations reduce the D_α emission in most of the observed region and, therefore, have to be taken into account when interpreting the amplitude of the D_α emission. On the other hand, higher order statistical moments (skewness, kurtosis) and turbulence characteristics (such as correlation length, or the autocorrelation time) are not significantly affected by the neutral fluctuations. At distances from the gas puff larger than the neutral mean free path, a non-local shadowing effect influences the neutral density fluctuations. There, the D_α fluctuations are correlated with the neutral density fluctuations, and the high-order statistical moments and measurements of other turbulence properties are strongly affected by the neutral density fluctuations.

Fully Modulated Turbulent Diffusion Flames in Microgravity*

NASA Astrophysics Data System (ADS)

Sangras, Ravikiran; Hermanson, James C.; Johari, Hamid; Stocker, Dennis P.; Hegde, Uday G.

2001-11-01

Fully modulated, turbulent diffusion flames are studied in microgravity in 2.2 s drop-tower tests with a co-flow combustor. The fuel consists of pure ethylene or a 50/50 mixture with nitrogen; the oxidizer is either normal air or up to 40% oxygen in nitrogen. A fast solenoid valve is used to fully modulate (completely shut off) the fuel flow. The injection times range from 5 to 400 ms with a duty-cycle of 0.1 - 0.5. The fuel nozzle is 2 mm in diameter with a jet Reynolds number of 5000. The shortest injection times yield compact puffs with a mean flame length as little as 20% of that of the steady-state flame. The reduction in flame length appears to be somewhat greater in microgravity than in normal gravity. As the injection time increases, elongated flames result with a mean flame length comparable to that of a steady flame. The injection time for which the steady-state flame length is approached is shorter for lower air/fuel ratios. For a given duty-cycle, the separation between puffs is greater in microgravity than in normal gravity. For compact puffs, increasing the duty-cycle appears to increase the flame length more in microgravity than in normal gravity. The microgravity flame puffs do not exhibit the vortex-ring-like structure seen in normal gravity.

Development, validation and application of a device to measure e-cigarette users' puffing topography.

PubMed

Cunningham, Anthony; Slayford, Sandra; Vas, Carl; Gee, Jodie; Costigan, Sandra; Prasad, Krishna

2016-10-10

With the rapidly rising popularity and substantial evolution of electronic cigarettes (e-cigarettes) in the past 5-6 years, how these devices are used by vapers and consumers' exposure to aerosol emissions need to be understood. We used puffing topography to measure directly product use. We adapted a cigarette puffing topography device for use with e-cigarettes. We performed validation using air and e-cigarette aerosol under multiple regimes. Consumer puffing topography was measured for 60 vapers provided with rechargeable "cig-a-like" or larger button-activated e-cigarettes, to use ad-libitum in two sessions. Under all regimes, air puff volumes were within 1 mL of the target and aerosol volumes within 5 mL for all device types, serving to validate the device. Vapers' mean puff durations (2.0 s and 2.2 s) were similar with both types of e-cigarette, but mean puff volumes (52.2 mL and 83.0 mL) and mean inter-puff intervals (23.2 s and 29.3 s) differed significantly. The differing data show that product characteristics influence puffing topography and, therefore, the results obtained from a given e-cigarette might not read across to other products. Understanding the factors that affect puffing topography will be important for standardising testing protocols for e-cigarette emissions.

'Carcinogens in a puff': smoking in Hong Kong movies.

PubMed

Ho, Sai-Yin; Wang, Man-Ping; Lai, Hak-Kan; Hedley, Anthony J; Lam, Tai-Hing

2010-12-01

Smoking scenes in movies, exploited by the tobacco industry to circumvent advertisement bans, are linked to adolescent smoking. Recently, a Hong Kong romantic comedy Love in a puff put smoking at centre stage, with numerous smoking scenes and words that glamourise smoking. Although WHO has issued guidelines on reducing the exposure of children to smoking in movies, none is adopted in Hong Kong. Comprehensive tobacco control strategies are urgently needed to protect young people in Hong Kong from cigarette promotion in movies.

Variational Iterative Refinement Source Term Estimation Algorithm Assessment for Rural and Urban Environments

NASA Astrophysics Data System (ADS)

Delle Monache, L.; Rodriguez, L. M.; Meech, S.; Hahn, D.; Betancourt, T.; Steinhoff, D.

2016-12-01

It is necessary to accurately estimate the initial source characteristics in the event of an accidental or intentional release of a Chemical, Biological, Radiological, or Nuclear (CBRN) agent into the atmosphere. The accurate estimation of the source characteristics are important because many times they are unknown and the Atmospheric Transport and Dispersion (AT&D) models rely heavily on these estimates to create hazard assessments. To correctly assess the source characteristics in an operational environment where time is critical, the National Center for Atmospheric Research (NCAR) has developed a Source Term Estimation (STE) method, known as the Variational Iterative Refinement STE algorithm (VIRSA). VIRSA consists of a combination of modeling systems. These systems include an AT&D model, its corresponding STE model, a Hybrid Lagrangian-Eulerian Plume Model (H-LEPM), and its mathematical adjoint model. In an operational scenario where we have information regarding the infrastructure of a city, the AT&D model used is the Urban Dispersion Model (UDM) and when using this model in VIRSA we refer to the system as uVIRSA. In all other scenarios where we do not have the city infrastructure information readily available, the AT&D model used is the Second-order Closure Integrated PUFF model (SCIPUFF) and the system is referred to as sVIRSA. VIRSA was originally developed using SCIPUFF 2.4 for the Defense Threat Reduction Agency and integrated into the Hazard Prediction and Assessment Capability and Joint Program for Information Systems Joint Effects Model. The results discussed here are the verification and validation of the upgraded system with SCIPUFF 3.0 and the newly implemented UDM capability. To verify uVIRSA and sVIRSA, synthetic concentration observation scenarios were created in urban and rural environments and the results of this verification are shown. Finally, we validate the STE performance of uVIRSA using scenarios from the Joint Urban 2003 (JU03) experiment, which was held in Oklahoma City and also validate the performance of sVIRSA using scenarios from the FUsing Sensor Integrated Observing Network (FUSION) Field Trial 2007 (FFT07), held at Dugway Proving Grounds in rural Utah.

Neutron spectra from beam-target reactions in dense Z-pinches

NASA Astrophysics Data System (ADS)

Appelbe, B.; Chittenden, J.

2015-10-01

The energy spectrum of neutrons emitted by a range of deuterium and deuterium-tritium Z-pinch devices is investigated computationally using a hybrid kinetic-MHD model. 3D MHD simulations are used to model the implosion, stagnation, and break-up of dense plasma focus devices at currents of 70 kA, 500 kA, and 2 MA and also a 15 MA gas puff. Instabilities in the MHD simulations generate large electric and magnetic fields, which accelerate ions during the stagnation and break-up phases. A kinetic model is used to calculate the trajectories of these ions and the neutron spectra produced due to the interaction of these ions with the background plasma. It is found that these beam-target neutron spectra are sensitive to the electric and magnetic fields at stagnation resulting in significant differences in the spectra emitted by each device. Most notably, magnetization of the accelerated ions causes the beam-target spectra to be isotropic for the gas puff simulations. It is also shown that beam-target spectra can have a peak intensity located at a lower energy than the peak intensity of a thermonuclear spectrum. A number of other differences in the shapes of beam-target and thermonuclear spectra are also observed for each device. Finally, significant differences between the shapes of beam-target DD and DT neutron spectra, due to differences in the reaction cross-sections, are illustrated.

A gas-puff-driven theta pinch for plasma-surface interaction studies

NASA Astrophysics Data System (ADS)

Jung, Soonwook; Kesler, Leigh; Yun, Hyun-Ho; Curreli, Davide; Andruczyk, Daniel; Ruzic, David

2012-10-01

DEVeX is a theta pinch device used to investigate fusion-related material interaction such as vapor shielding and ICRF antenna interactions with plasma-pulses in a laboratory setting. The simulator is required to produce high heat-flux plasma enough to induce temperature gradient high enough to study extreme conditions happened in a plasma fusion reactor. In order to achieve it, DEVeX is reconfigured to be combined with gas puff system as gas puffing may reduce heat flux loss resulting from collisions with neutral. A gas puff system as well as a conical gas nozzle is manufactured and several diagnostics including hot wire anemometer and fast ionization gauge are carried out to quantitatively estimate the supersonic flow of gas. Energy deposited on the target for gas puffing and static-filled conditions is measured with thermocouples and its application to TELS, an innovative concept utilizing a thermoelectric-driven liquid metal flow for plasma facing component, is discussed.

Dynamics of Isolated and Interacting Flame Structures in Strongly-Pulsed, Turbulent Jet Flames

NASA Astrophysics Data System (ADS)

Fregeau, Mathieu; Liao, Ying-Hao; Hermanson, James; Stocker, Dennis; Hegde, Uday

2007-11-01

The dynamics of the large-scale structures in strongly-pulsed, turbulent diffusion flames were studied in normal- and microgravity. Cross-correlation of temperature measurements and high-speed flame imaging were used to estimate the celerity of the flame structures. Both diagnostics indicate a marked increase in celerity with the increasing flame puff interaction as the jet off-time decreases. The celerity is also generally higher for shorter injection times, which yield more compact flame puffs. These trends are seen both for the case of fixed injection velocity as well as for the case of fixed fueling rate. The celerity correlates well with the inverse downstream distance scaled with an appropriate injection parameter, suggesting that the impact of buoyancy can be partially accounted for by the corresponding changes in the mean flame length. Differences in the values of celerity determined by the temperature and visual techniques can be attributed to nature of the evolution of the flame puffs with downstream distance.

The results of the study of compact gas-puff and vacuum spark plasma sources of SXR with Glass-Capillary Converters (GCC)

NASA Astrophysics Data System (ADS)

Shlyaptseva, Alla; Kantsyrev, Victor; Inozemtsev, Andrei; Petrukhin, Oleg

1994-06-01

The results are presented dealing with the working out and study of the SXR compact plasma source. The experimental set up included a compact new 'gas-puff' source with parameters being better than the traditional ones and a new type of SXR source - low-inductance vacuum spark (LIVS) with glass-capillary converters (GCC) of SXR. The compact plasma 'gas-puff' source had the high value of the z approx. (1-2) 10(exp -2) (conversion coefficient of initial energy supply into SXR); a small effective size of emission region and greater resource. The characteristics of LIVS with GCC were studied. GCC consisting of about several hundreds of glass capillaries allowed us to focus SXR, to change the cross section of SXR beams to plasma sources, and to change SXR spectrum. The possibility was shown of using of GCC in plasma diagnostics of powerful plasma devices: for X-ray microscopy and to study the influence of SXR on the solid state surface.

Blob-hole correlation model for edge turbulence and comparisons with NSTX gas puff imaging data

NASA Astrophysics Data System (ADS)

Myra, J. R.; Zweben, S. J.; Russell, D. A.

2018-07-01

Gas puff imaging (GPI) observations made in NSTX (Zweben et al 2017 Phys. Plasmas 24 102509) have revealed two-point spatial correlations of edge and scrape-off layer (SOL) turbulence in the plane perpendicular to the magnetic field. A common feature is the occurrence of dipole-like patterns with significant regions of negative correlation. In this paper, we explore the possibility that these dipole patterns may be due to blob-hole pairs. Statistical methods are applied to determine the two-point spatial correlation that results from a model of blob-hole pair formation. It is shown that the model produces dipole correlation patterns that are qualitatively similar to the GPI data in several respects. Effects of the reference location (confined surfaces or SOL), a superimposed random background, hole velocity and lifetime, and background sheared flows are explored and discussed with respect to experimental observations. Additional analysis of the experimental GPI dataset is performed to further test this blob-hole correlation model. A time delay two-point spatial correlation study did not reveal inward propagation of the negative correlation structures that were postulated to correspond to holes in the data nor did it suggest that the negative correlation structures are due to neutral shadowing. However, tracking of the highest and lowest values (extrema) of the normalized GPI fluctuations shows strong evidence for mean inward propagation of minima and outward propagation of maxima, in qualitative agreement with theoretical expectations. Other properties of the experimentally observed extrema are discussed.

Sex/Gender Differences in Cotinine Levels Among Daily Smokers in the Pennsylvania Adult Smoking Study.

PubMed

Chen, Allshine; Krebs, Nicolle M; Zhu, Junjia; Sun, Dongxiao; Stennett, Andrea; Muscat, Joshua E

2017-11-01

This study was conducted to determine sex/gender differences in smoke exposure and to quantify the role of potential predictors including puffing behaviors, nicotine dependence, and non-nicotinic factors. The Pennsylvania Adult Smoking Study (PASS) of 332 adult cigarette smokers utilized portable handheld topography devices to capture the smokers' profiles in a naturalistic environment. Sex/gender differences in salivary biomarkers were modeled using ANCOVA to account for measures of dependence (Fagerstrom Test for Nicotine Dependence, nicotine metabolite ratio [3-hydroxycotinine/cotinine]), and nondependence covariates including anthropomorphic factors and stress. The Blinder-Oaxaca method was used to decompose the sex/gender differences in nicotine uptake due to covariates. Men had significantly higher cotinine levels (313.5 ng/mL vs. 255.8 ng/mL, p < 0.01), cotinine +3-hydroxycotinine levels, (0.0787 mol/L vs. 0.0675 mol/L, p = 0.01), puff volumes (52.95 mL vs. 44.77 mL, p < 0.01), and a lower nicotine metabolite ratio (0.396 vs. 0.475, p = 0.01) than women. The mean Fagerström Test for Nicotine Dependence score did not differ between men and women (p = 0.24). Women had a higher mean Hooked on Tobacco Checklist score than men (7.64 vs. 6.87, p < 0.01). In multivariate analysis, nicotine metabolite levels were not significantly different by sex. Decomposition results show that ten predictors can explain 83% of the sex/gender differences in cotinine uptake. Height was the greatest contributor to these differences, followed by average puff volume. Conclusion and Impact: The higher levels of nicotine metabolites in men, compared to women, can be explained by height, weight, puff volume, and nicotine metabolism.

Examining Daily Electronic Cigarette Puff Topography Among Established and Non-established Cigarette Smokers in their Natural Environment.

PubMed

Lee, Youn Ok; Nonnemaker, James M; Bradfield, Brian; Hensel, Edward C; Robinson, Risa J

2017-10-04

Understanding exposures and potential health effects of ecigarettes is complex. Users' puffing behavior, or topography, affects function of ecigarette devices (e.g., coil temperature) and composition of their emissions. Users with different topographies are likely exposed to different amounts of any harmful or potentially harmful constituents (HPHCs). In this study, we compare ecigarette topographies of established cigarette smokers and non-established cigarette smokers. Data measuring e-cigarette topography were collected using a wireless hand-held monitoring device in users' everyday lives over 1 week. Young adult (aged 18-25) participants (N=20) used disposable e-cigarettes with the monitor as they normally would and responded to online surveys. Topography characteristics of established versus non-established cigarette smokers were compared. On average, established cigarette smokers in the sample had larger first puff volume (130.9ml vs. 56.0ml, p<.05) and larger puff volume per session (1,509.3ml vs. 651.7ml, p<.05) compared with non-established smokers. At marginal significance, they had longer sessions (566.3s vs. 279.7s, p=.06) and used e-cigarettes more sessions per day (5.3s vs. 3.5s, p=.14). Established cigarette smokers also used ecigarettes for longer puff durations (3.3s vs. 1.8s, p<.01) and had larger puff volume (110.3ml vs. 54.7ml, p<.05) compared with non-established smokers. At marginal significance, they had longer puff interval (38.1s vs. 21.7s, p=.05). Our results demonstrate that topography characteristics differ by level of current cigarette smoking. This suggests that exposures to constituents of e-cigarettes depends on user characteristics and that specific topography parameters may be needed for different user populations when assessing ecigarette health effects. A user's topography affects his or her exposure to HPHCs. As this study demonstrates, user characteristics, such as level of smoking, can influence topography. Thus, it is crucial to understand the topography profiles of different user types to assess the potential for population harm and to identify potentially vulnerable populations. This study only looked at topography of cigarette smokers using disposable e-cigarettes. Further research is needed to better understand potential variation in ecigarette topography and resulting exposures to HPHCs among users of different e-cigarette devices and liquids. © The Author 2017. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Effects of Electronic Cigarette Liquid Nicotine Concentration on Plasma Nicotine and Puff Topography in Tobacco Cigarette Smokers: A Preliminary Report.

PubMed

Lopez, Alexa A; Hiler, Marzena M; Soule, Eric K; Ramôa, Carolina P; Karaoghlanian, Nareg V; Lipato, Thokozeni; Breland, Alison B; Shihadeh, Alan L; Eissenberg, Thomas

2016-05-01

Electronic cigarettes (ECIGs) aerosolize a liquid that usually contains propylene glycol and/or vegetable glycerin, flavorants, and the dependence-producing drug nicotine in various concentrations. This study examined the extent to which ECIG liquid nicotine concentration is related to user plasma nicotine concentration in ECIG-naïve tobacco cigarette smokers. Sixteen ECIG-naïve cigarette smokers completed four laboratory sessions that differed by the nicotine concentration of the liquid (0, 8, 18, or 36 mg/ml) that was placed into a 1.5 Ohm, dual coil "cartomizer" powered by a 3.3V battery. In each session, participants completed two, 10-puff ECIG use bouts with a 30-second inter-puff interval; bouts were separated by 60 minutes. Venous blood was sampled before and after bouts for later analysis of plasma nicotine concentration; puff duration, volume, and average flow rate were measured during each bout. In bout 1, relative to the 0mg/ml nicotine condition (mean = 3.8 ng/ml, SD = 3.3), plasma nicotine concentration increased significantly immediately after the bout for the 8 (mean = 8.8 ng/ml, SD = 6.3), 18 (mean = 13.2 ng/ml, SD = 13.2), and 36 mg/ml (mean = 17.0 ng/ml, SD = 17.9) liquid concentration. A similar pattern was observed after bout 2. Average puff duration in the 36 mg/ml condition was significantly shorter compared to the 0mg/ml nicotine condition. Puff volume increased during the second bout for 8 and 18 mg/ml conditions. For a given ECIG device, nicotine delivery may be directly related to liquid concentration. ECIG-naïve cigarette smokers can, from their first use bout, attain cigarette-like nicotine delivery profiles with some currently available ECIG products. Liquid nicotine concentration can influence plasma nicotine concentration in ECIG-naïve cigarette smokers, and, at some concentrations, the nicotine delivery profile of a 3.3V ECIG with a dual coil, 1.5-Ohm cartomizer approaches that of a combustible tobacco cigarette in this population. Finding a product that delivers nicotine as effectively as a tobacco cigarette, as we report here, may be essential for smokers who want to replace completely their combustible tobacco cigarettes with ECIGs. © The Author 2015. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Development And Characterization Of A Liner-On-Target Injector For Staged Z-Pinch Experiments

NASA Astrophysics Data System (ADS)

Valenzuela, J. C.; Conti, F.; Krasheninnikov, I.; Narkis, J.; Beg, F.; Wessel, F. J.; Rahman, H. U.

2016-10-01

We present the design and optimization of a liner-on-target injector for Staged Z-pinch experiments. The injector is composed of an annular high atomic number (e.g. Ar, Kr) gas-puff and an on-axis plasma gun that delivers the ionized deuterium target. The liner nozzle injector has been carefully studied using Computational Fluid Dynamics (CFD) simulations to produce a highly collimated 1 cm radius gas profile that satisfies the theoretical requirement for best performance on the 1 MA Zebra current driver. The CFD simulations produce density profiles as a function of the nozzle shape and gas. These profiles are initialized in the MHD MACH2 code to find the optimal liner density for a stable, uniform implosion. We use a simple Snowplow model to study the plasma sheath acceleration in a coaxial plasma gun to help us properly design the target injector. We have performed line-integrated density measurements using a CW He-Ne laser to characterize the liner gas and the plasma gun density as a function of time. The measurements are compared with models and calculations and benchmarked accordingly. Advanced Research Projects Agency - Energy, DE-AR0000569.

Asymmetrical Macromolecular Complex Formation of Lysophosphatidic Acid Receptor 2 (LPA2) Mediates Gradient Sensing in Fibroblasts*

PubMed Central

Ren, Aixia; Moon, Changsuk; Zhang, Weiqiang; Sinha, Chandrima; Yarlagadda, Sunitha; Arora, Kavisha; Wang, Xusheng; Yue, Junming; Parthasarathi, Kaushik; Heil-Chapdelaine, Rick; Tigyi, Gabor; Naren, Anjaparavanda P.

2014-01-01

Chemotactic migration of fibroblasts toward growth factors relies on their capacity to sense minute extracellular gradients and respond to spatially confined receptor-mediated signals. Currently, mechanisms underlying the gradient sensing of fibroblasts remain poorly understood. Using single-particle tracking methodology, we determined that a lysophosphatidic acid (LPA) gradient induces a spatiotemporally restricted decrease in the mobility of LPA receptor 2 (LPA2) on chemotactic fibroblasts. The onset of decreased LPA2 mobility correlates to the spatial recruitment and coupling to LPA2-interacting proteins that anchor the complex to the cytoskeleton. These localized PDZ motif-mediated macromolecular complexes of LPA2 trigger a Ca2+ puff gradient that governs gradient sensing and directional migration in response to LPA. Disruption of the PDZ motif-mediated assembly of the macromolecular complex of LPA2 disorganizes the gradient of Ca2+ puffs, disrupts gradient sensing, and reduces the directional migration of fibroblasts toward LPA. Our findings illustrate that the asymmetric macromolecular complex formation of chemoattractant receptors mediates gradient sensing and provides a new mechanistic basis for models to describe gradient sensing of fibroblasts. PMID:25542932

Video-Puff of Air Hits Ball of Water in Space Onboard the International Space Station (ISS)

NASA Technical Reports Server (NTRS)

2003-01-01

Saturday Morning Science, the science of opportunity series of applied experiments and demonstrations, performed aboard the International Space Station (ISS) by Expedition 6 astronaut Dr. Don Pettit, revealed some remarkable findings. In this video clip, Dr. Pettit demonstrates the phenomenon of a puff of air hitting a ball of water that is free floating in space. Watch the video to see why Dr. Pettit remarks 'I'd hate think that our planet would go through these kinds of gyrations if it got whacked by a big asteroid'.

Component-specific, cigarette particle deposition modeling in the human respiratory tract

PubMed Central

Price, Owen T.; Yurteri, Caner U.; Dickens, Colin; McAughey, John

2014-01-01

Inhalation of cigarette smoke particles (CSP) leads to adverse health effects in smokers. Determination of the localized dose to the lung of the inhaled smoke aids in determining vulnerable sites, and identifying components of the smoke that may be responsible for the adverse effects; thus providing a roadmap for harm reduction of cigarette smoking. A particle deposition model specific to CSP was developed for the oral cavity and the lung by accounting for cigarette particle size growth by hygroscopicity, phase change and coagulation. In addition, since the cigarette puff enters the respiratory tract as a dense cloud, the cloud effect on particle drag and deposition was accounted for in the deposition model. Models of particle losses in the oral cavities were developed during puff drawing and subsequent mouth-hold. Cigarette particles were found to grow by hygroscopicity and coagulation, but to shrink as a result of nicotine evaporation. The particle size reached a plateau beyond which any disturbances in the environmental conditions caused the various mechanisms to balance each other out and the particle size remain stable. Predicted particle deposition considering the cloud effects was greater than when treated as a collection of non-interacting particles (i.e. no cloud effects). Accounting for cloud movement provided the necessary physical mechanism to explain the greater than expected, experimentally observed and particle deposition. The deposition model for CSP can provide the necessary input to determine the fate of inhaled CSP in the lung. The knowledge of deposition will be helpful for health assessment and identification and reduction of harmful components of CSP. PMID:24354791

A Bayesian method to rank different model forecasts of the same volcanic ash cloud: Chapter 24

USGS Publications Warehouse

Denlinger, Roger P.; Webley, P.; Mastin, Larry G.; Schwaiger, Hans F.

2012-01-01

Volcanic eruptions often spew fine ash high into the atmosphere, where it is carried downwind, forming long ash clouds that disrupt air traffic and pose a hazard to air travel. To mitigate such hazards, the community studying ash hazards must assess risk of ash ingestion for any flight path and provide robust and accurate forecasts of volcanic ash dispersal. We provide a quantitative and objective method to evaluate the efficacy of ash dispersal estimates from different models, using Bayes theorem to assess the predictions that each model makes about ash dispersal. We incorporate model and measurement uncertainty and produce a posterior probability for model input parameters. The integral of the posterior over all possible combinations of model inputs determines the evidence for each model and is used to compare models. We compare two different types of transport models, an Eulerian model (Ash3d) and a Langrangian model (PUFF), as applied to the 2010 eruptions of Eyjafjallajökull volcano in Iceland. The evidence for each model benefits from common physical characteristics of ash dispersal from an eruption column and provides a measure of how well each model forecasts cloud transport. Given the complexity of the wind fields, we find that the differences between these models depend upon the differences in the way the models disperse ash into the wind from the source plume. With continued observation, the accuracy of the estimates made by each model increases, increasing the efficacy of each model’s ability to simulate ash dispersal.

A Thomson-type mass and energy spectrometer for characterizing ion energy distributions in a coaxial plasma gun operating in a gas-puff mode

PubMed Central

Rieker, G. B.; Poehlmann, F. R.; Cappelli, M. A.

2013-01-01

Measurements of ion energy distribution are performed in the accelerated plasma of a coaxial electromagnetic plasma gun operating in a gas-puff mode at relatively low discharge energy (900 J) and discharge potential (4 kV). The measurements are made using a Thomson-type mass and energy spectrometer with a gated microchannel plate and phosphor screen as the ion sensor. The parabolic ion trajectories are captured from the sensor screen with an intensified charge-coupled detector camera. The spectrometer was designed and calibrated using the Geant4 toolkit, accounting for the effects on the ion trajectories of spatial non-uniformities in the spectrometer magnetic and electric fields. Results for hydrogen gas puffs indicate the existence of a class of accelerated protons with energies well above the coaxial discharge potential (up to 24 keV). The Thomson analyzer confirms the presence of impurities of copper and iron, also of relatively high energies, which are likely erosion or sputter products from plasma-electrode interactions. PMID:23983449

A Thomson-type mass and energy spectrometer for characterizing ion energy distributions in a coaxial plasma gun operating in a gas-puff mode

NASA Astrophysics Data System (ADS)

Rieker, G. B.; Poehlmann, F. R.; Cappelli, M. A.

2013-07-01

Measurements of ion energy distribution are performed in the accelerated plasma of a coaxial electromagnetic plasma gun operating in a gas-puff mode at relatively low discharge energy (900 J) and discharge potential (4 kV). The measurements are made using a Thomson-type mass and energy spectrometer with a gated microchannel plate and phosphor screen as the ion sensor. The parabolic ion trajectories are captured from the sensor screen with an intensified charge-coupled detector camera. The spectrometer was designed and calibrated using the Geant4 toolkit, accounting for the effects on the ion trajectories of spatial non-uniformities in the spectrometer magnetic and electric fields. Results for hydrogen gas puffs indicate the existence of a class of accelerated protons with energies well above the coaxial discharge potential (up to 24 keV). The Thomson analyzer confirms the presence of impurities of copper and iron, also of relatively high energies, which are likely erosion or sputter products from plasma-electrode interactions.

A Thomson-type mass and energy spectrometer for characterizing ion energy distributions in a coaxial plasma gun operating in a gas-puff mode.

PubMed

Rieker, G B; Poehlmann, F R; Cappelli, M A

2013-07-01

Measurements of ion energy distribution are performed in the accelerated plasma of a coaxial electromagnetic plasma gun operating in a gas-puff mode at relatively low discharge energy (900 J) and discharge potential (4 kV). The measurements are made using a Thomson-type mass and energy spectrometer with a gated microchannel plate and phosphor screen as the ion sensor. The parabolic ion trajectories are captured from the sensor screen with an intensified charge-coupled detector camera. The spectrometer was designed and calibrated using the Geant4 toolkit, accounting for the effects on the ion trajectories of spatial non-uniformities in the spectrometer magnetic and electric fields. Results for hydrogen gas puffs indicate the existence of a class of accelerated protons with energies well above the coaxial discharge potential (up to 24 keV). The Thomson analyzer confirms the presence of impurities of copper and iron, also of relatively high energies, which are likely erosion or sputter products from plasma-electrode interactions.

Evaluation of heat and particle controllability on the JT-60SA divertor

NASA Astrophysics Data System (ADS)

Kawashima, H.; Hoshino, K.; Shimizu, K.; Takizuka, T.; Ide, S.; Sakurai, S.; Asakura, N.

2011-08-01

The JT-60SA divertor design has been established on the basis of engineering requirements and physics analysis. Heat and particle fluxes under the full input power of 41 MW can give severe heat loads on the divertor targets, while the allowable heat load is limited below 15 MW/m2. Dependence of the heat flux mitigation on a D2 gas-puff is evaluated by SONIC simulations for high density (ne_ave ˜ 1 × 1020 m-3) high current plasmas. It is found that the peak heat load 10 MW/m2 with dense (ned > 4 × 1020 m-3) and cold (Ted, Tid ⩽ 1 eV) divertor plasmas are obtained at a moderate gas-puff of Γpuff = 15 × 1021 s-1. Divertor plasmas are controlled from attached to detached condition using the divertor pump with pumping-speed below 100 m3/s. In full non-inductive current drive plasmas with low density (ne_ave ˜ 5 × 1019 m-3), the reduction of divertor heat load is achieved with the Ar injection.

Industrial point source CO2 emission strength estimation with aircraft measurements and dispersion modelling.

PubMed

Carotenuto, Federico; Gualtieri, Giovanni; Miglietta, Franco; Riccio, Angelo; Toscano, Piero; Wohlfahrt, Georg; Gioli, Beniamino

2018-02-22

CO 2 remains the greenhouse gas that contributes most to anthropogenic global warming, and the evaluation of its emissions is of major interest to both research and regulatory purposes. Emission inventories generally provide quite reliable estimates of CO 2 emissions. However, because of intrinsic uncertainties associated with these estimates, it is of great importance to validate emission inventories against independent estimates. This paper describes an integrated approach combining aircraft measurements and a puff dispersion modelling framework by considering a CO 2 industrial point source, located in Biganos, France. CO 2 density measurements were obtained by applying the mass balance method, while CO 2 emission estimates were derived by implementing the CALMET/CALPUFF model chain. For the latter, three meteorological initializations were used: (i) WRF-modelled outputs initialized by ECMWF reanalyses; (ii) WRF-modelled outputs initialized by CFSR reanalyses and (iii) local in situ observations. Governmental inventorial data were used as reference for all applications. The strengths and weaknesses of the different approaches and how they affect emission estimation uncertainty were investigated. The mass balance based on aircraft measurements was quite succesful in capturing the point source emission strength (at worst with a 16% bias), while the accuracy of the dispersion modelling, markedly when using ECMWF initialization through the WRF model, was only slightly lower (estimation with an 18% bias). The analysis will help in highlighting some methodological best practices that can be used as guidelines for future experiments.

Blob-hole correlation model for edge turbulence and comparisons with NSTX gas puff imaging data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myra, J. R.; Zweben, S. J.; Russell, D. A.

We report that gas puff imaging (GPI) observations made in NSTX [Zweben S J, et al., 2017 Phys. Plasmas 24 102509] have revealed two-point spatial correlations of edge and scrape-off layer turbulence in the plane perpendicular to the magnetic field. A common feature is the occurrence of dipole-like patterns with significant regions of negative correlation. In this paper, we explore the possibility that these dipole patterns may be due to blob-hole pairs. Statistical methods are applied to determine the two-point spatial correlation that results from a model of blob-hole pair formation. It is shown that the model produces dipole correlationmore » patterns that are qualitatively similar to the GPI data in several respects. Effects of the reference location (confined surfaces or scrape-off layer), a superimposed random background, hole velocity and lifetime, and background sheared flows are explored and discussed with respect to experimental observations. Additional analysis of the experimental GPI dataset is performed to further test this blob-hole correlation model. A time delay two-point spatial correlation study did not reveal inward propagation of the negative correlation structures that were postulated to correspond to holes in the data nor did it suggest that the negative correlation structures are due to neutral shadowing. However, tracking of the highest and lowest values (extrema) of the normalized GPI fluctuations shows strong evidence for mean inward propagation of minima and outward propagation of maxima, in qualitative agreement with theoretical expectations. Finally, other properties of the experimentally observed extrema are discussed.« less

Blob-hole correlation model for edge turbulence and comparisons with NSTX gas puff imaging data

DOE PAGES

Myra, J. R.; Zweben, S. J.; Russell, D. A.

2018-05-15

We report that gas puff imaging (GPI) observations made in NSTX [Zweben S J, et al., 2017 Phys. Plasmas 24 102509] have revealed two-point spatial correlations of edge and scrape-off layer turbulence in the plane perpendicular to the magnetic field. A common feature is the occurrence of dipole-like patterns with significant regions of negative correlation. In this paper, we explore the possibility that these dipole patterns may be due to blob-hole pairs. Statistical methods are applied to determine the two-point spatial correlation that results from a model of blob-hole pair formation. It is shown that the model produces dipole correlationmore » patterns that are qualitatively similar to the GPI data in several respects. Effects of the reference location (confined surfaces or scrape-off layer), a superimposed random background, hole velocity and lifetime, and background sheared flows are explored and discussed with respect to experimental observations. Additional analysis of the experimental GPI dataset is performed to further test this blob-hole correlation model. A time delay two-point spatial correlation study did not reveal inward propagation of the negative correlation structures that were postulated to correspond to holes in the data nor did it suggest that the negative correlation structures are due to neutral shadowing. However, tracking of the highest and lowest values (extrema) of the normalized GPI fluctuations shows strong evidence for mean inward propagation of minima and outward propagation of maxima, in qualitative agreement with theoretical expectations. Finally, other properties of the experimentally observed extrema are discussed.« less

An integrated simulation and optimization approach for managing human health risks of atmospheric pollutants by coal-fired power plants.

PubMed

Dai, C; Cai, X H; Cai, Y P; Guo, H C; Sun, W; Tan, Q; Huang, G H

2014-06-01

This research developed a simulation-aided nonlinear programming model (SNPM). This model incorporated the consideration of pollutant dispersion modeling, and the management of coal blending and the related human health risks within a general modeling framework In SNPM, the simulation effort (i.e., California puff [CALPUFF]) was used to forecast the fate of air pollutants for quantifying the health risk under various conditions, while the optimization studies were to identify the optimal coal blending strategies from a number of alternatives. To solve the model, a surrogate-based indirect search approach was proposed, where the support vector regression (SVR) was used to create a set of easy-to-use and rapid-response surrogates for identifying the function relationships between coal-blending operating conditions and health risks. Through replacing the CALPUFF and the corresponding hazard quotient equation with the surrogates, the computation efficiency could be improved. The developed SNPM was applied to minimize the human health risk associated with air pollutants discharged from Gaojing and Shijingshan power plants in the west of Beijing. Solution results indicated that it could be used for reducing the health risk of the public in the vicinity of the two power plants, identifying desired coal blending strategies for decision makers, and considering a proper balance between coal purchase cost and human health risk. A simulation-aided nonlinear programming model (SNPM) is developed. It integrates the advantages of CALPUFF and nonlinear programming model. To solve the model, a surrogate-based indirect search approach based on the combination of support vector regression and genetic algorithm is proposed. SNPM is applied to reduce the health risk caused by air pollutants discharged from Gaojing and Shijingshan power plants in the west of Beijing. Solution results indicate that it is useful for generating coal blending schemes, reducing the health risk of the public, reflecting the trade-offbetween coal purchase cost and health risk.

A Genetic RNAi Screen for IP3/Ca2+ Coupled GPCRs in Drosophila Identifies the PdfR as a Regulator of Insect Flight

PubMed Central

Agrawal, Tarjani; Sadaf, Sufia; Hasan, Gaiti

2013-01-01

Insect flight is regulated by various sensory inputs and neuromodulatory circuits which function in synchrony to control and fine-tune the final behavioral outcome. The cellular and molecular bases of flight neuromodulatory circuits are not well defined. In Drosophila melanogaster, it is known that neuronal IP3 receptor mediated Ca2+ signaling and store-operated Ca2+ entry (SOCE) are required for air-puff stimulated adult flight. However, G-protein coupled receptors (GPCRs) that activate intracellular Ca2+ signaling in the context of flight are unknown in Drosophila. We performed a genetic RNAi screen to identify GPCRs that regulate flight by activating the IP3 receptor. Among the 108 GPCRs screened, we discovered 5 IP3/Ca2+ linked GPCRs that are necessary for maintenance of air-puff stimulated flight. Analysis of their temporal requirement established that while some GPCRs are required only during flight circuit development, others are required both in pupal development as well as during adult flight. Interestingly, our study identified the Pigment Dispersing Factor Receptor (PdfR) as a regulator of flight circuit development and as a modulator of acute flight. From the analysis of PdfR expressing neurons relevant for flight and its well-defined roles in other behavioral paradigms, we propose that PdfR signaling functions systemically to integrate multiple sensory inputs and modulate downstream motor behavior. PMID:24098151

Independent sailing with high tetraplegia using sip and puff controls: integration into a community sailing center.

PubMed

Rojhani, Solomon; Stiens, Steven A; Recio, Albert C

2017-07-01

We are continually rediscovering how adapted recreational activity complements the rehabilitation process, enriches patients' lives and positively impacts outcome measures. Although sports for people with spinal cord injuries (SCI) has achieved spectacular visibility, participation by high cervical injuries is often restricted due to poor accessibility, safety concerns, lack of adaptability, and high costs of technology. We endeavor to demonstrate the mechanisms, adaptability, accessibility, and benefits the sport of sailing creates in the rehabilitative process. Our sailor is a 27-year-old man with a history of traumatic SCI resulting in C4 complete tetraplegia. The participant completed an adapted introductory sailing course, and instruction on the sip-and-puff sail and tiller control mechanism. With practice, he navigated an on-water course in moderate winds of 5 to 15 knots. Despite trends toward shorter rehabilitation stays, aggressive transdisciplinary collaboration with recreation therapy can provide community and natural environment experiences while inpatient and continuing post discharge. Such peak physical and psychological experiences provide a positive perspective for the future that can be shared on the inpatient unit, with families and support systems like sailing clubs in the community. Rehabilitation theory directs a team process to achieve patient self-awareness and initiate self-actualization in spite of disablement. Utilization of local community sailing centers that have provided accessible assisted options provides person-centered self-realization of goals as assisted by family and natural supports. Such successful patients become native guides for others seeking the same experience.

Time-dependent analysis of visible helium line-ratios for electron temperature and density diagnostic using synthetic simulations on NSTX-U

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muñoz Burgos, J. M.; Barbui, T.; Schmitz, O.

Helium line-ratios for electron temperature (T e) and density (n e) plasma diagnostic in the Scrape-Off-Layer (SOL) and Edge regions of tokamaks are widely used. Due to their intensities and proximity of wavelengths, the singlet 667.8 and 728.1 nm, and triplet 706.5 nm visible lines have been typically preferred. Time-dependency of the triplet line (706.5 nm) has been previously analyzed in detail by including transient effects on line-ratios during gas-puff diagnostic applications. In this work, several line-ratio combinations within each of the two spin systems are analyzed with the purpose of eliminating transient effects to extend the application of thismore » powerful diagnostic to high temporal resolution characterization of plasmas. The analysis is done using synthetic emission modeling and diagnostic for low electron density NSTX SOL plasma conditions by several visible lines. Quasi-static equilibrium, and time-dependent models are employed to evaluate transient effects of the atomic population levels that may affect the derived electron temperatures and densities as the helium gas-puff penetrates the plasma. Ultimately, the analysis of a wider range of spectral lines will help to extend this powerful diagnostic to experiments where the wavelength range of the measured spectra may be constrained either by limitations of the spectrometer, or by other conflicting lines from different ions.« less

Time-dependent analysis of visible helium line-ratios for electron temperature and density diagnostic using synthetic simulations on NSTX-U

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muñoz Burgos, J. M., E-mail: jmunozbu@pppl.gov; Stutman, D.; Tritz, K.

Helium line-ratios for electron temperature (T{sub e}) and density (n{sub e}) plasma diagnostic in the Scrape-Off-Layer (SOL) and edge regions of tokamaks are widely used. Due to their intensities and proximity of wavelengths, the singlet, 667.8 and 728.1 nm, and triplet, 706.5 nm, visible lines have been typically preferred. Time-dependency of the triplet line (706.5 nm) has been previously analyzed in detail by including transient effects on line-ratios during gas-puff diagnostic applications. In this work, several line-ratio combinations within each of the two spin systems are analyzed with the purpose of eliminating transient effects to extend the application of thismore » powerful diagnostic to high temporal resolution characterization of plasmas. The analysis is done using synthetic emission modeling and diagnostic for low electron density NSTX SOL plasma conditions by several visible lines. Quasi-static equilibrium and time-dependent models are employed to evaluate transient effects of the atomic population levels that may affect the derived electron temperatures and densities as the helium gas-puff penetrates the plasma. The analysis of a wider range of spectral lines will help to extend this powerful diagnostic to experiments where the wavelength range of the measured spectra may be constrained either by limitations of the spectrometer or by other conflicting lines from different ions.« less

Time-dependent analysis of visible helium line-ratios for electron temperature and density diagnostic using synthetic simulations on NSTX-U

DOE PAGES

Muñoz Burgos, J. M.; Barbui, T.; Schmitz, O.; ...

2016-07-11

Helium line-ratios for electron temperature (T e) and density (n e) plasma diagnostic in the Scrape-Off-Layer (SOL) and Edge regions of tokamaks are widely used. Due to their intensities and proximity of wavelengths, the singlet 667.8 and 728.1 nm, and triplet 706.5 nm visible lines have been typically preferred. Time-dependency of the triplet line (706.5 nm) has been previously analyzed in detail by including transient effects on line-ratios during gas-puff diagnostic applications. In this work, several line-ratio combinations within each of the two spin systems are analyzed with the purpose of eliminating transient effects to extend the application of thismore » powerful diagnostic to high temporal resolution characterization of plasmas. The analysis is done using synthetic emission modeling and diagnostic for low electron density NSTX SOL plasma conditions by several visible lines. Quasi-static equilibrium, and time-dependent models are employed to evaluate transient effects of the atomic population levels that may affect the derived electron temperatures and densities as the helium gas-puff penetrates the plasma. Ultimately, the analysis of a wider range of spectral lines will help to extend this powerful diagnostic to experiments where the wavelength range of the measured spectra may be constrained either by limitations of the spectrometer, or by other conflicting lines from different ions.« less

Comparison of measured and modeled gas-puff emissions on Alcator C-Mod

NASA Astrophysics Data System (ADS)

Baek, Seung-Gyou; Terry, J. L.; Stotler, D. P.; Labombard, B. L.; Brunner, D. F.

2017-10-01

Understanding neutral transport in tokamak boundary plasmas is important because of its possible effects on the pedestal and scrape-off layer (SOL). On Alcator C-Mod, measured neutral line emissions from externally-puffed deuterium and helium gases are compared with the synthetic results of a neutral transport code, DEGAS 2. The injected gas flow rate and the camera response are absolutely calibrated. Time-averaged SOL density and temperature profiles are input to a steady-state simulation. An updated helium atomic model is employed in DEGAS2. Good agreement is found for the D α peak brightness and profile shape. However, the measured helium I line brightness is found to be lower than that in the simulation results by a roughly a factor of three over a wide range of density particularly in the far SOL region. Two possible causes for this discrepancy are reviewed. First, local cooling due to gas puff may suppress the line emission. Second, time-dependent turbulence effect may impact the helium neutral transport. Unlike deuterium atoms that gain energy from charge exchange and dissociation processes, helium neutrals remain cold and have a relatively short mean free path, known to make them prone to turbulence based on the Kubo number criterion. Supported by USDoE awards: DE-FC02-99ER54512, DE-SC0014251, and DE-AC02-09CH11466.

Use of red palm oil in local snacks can increase intake of provitamin A carotenoids in young aborigines children: a Malaysian experience.

PubMed

Ng, T K W; Low, C X; Kong, J P; Cho, Y L

2012-12-01

Carotenoid-rich red palm oil (RPO)-based snacks have been provided to children in impoverished communities to improve their vitamin A status. The non-availabilty of information on the acceptability of RPO-based snacks by Malaysian aborigines (Orang Asli) children forms the basis of this study. Twenty-one Orang Asli children, majority of whom had normal body mass index for age (BMI-for-age) and aged 4.73 +/- 0.92 years in Sungai Tekir, Negeri Sembilan were provided with three freshly-prepared snacks (springroll, curry puff or doughnut) each containing one teaspoon or 5 ml of RPO per serving, on separate mornings. On the fourth morning, one serving each of all 3 different snacks was provided together on a plate to every child for consumption and preference for the snacks recorded. The children's habitual vitamin A intakes were assessed by a semi-quantitative food frequency questionnaire (FFQ) and carotenoid retention tests for the prepared snacks were performed by column chromatography. Fifty-four percent of the children did not meet their RNI for vitamin A. Based on acceptance criterion of consuming at least one-half serving of the snacks provided, springroll and curry puff recorded 100% acceptability while doughnut had 82% acceptability. Preference of snack was in the order, springroll (47%) > doughtnut (35%) > curry puff (18%), but a Z-test test for proportions showed no statistical significance. Carotenoid retention tests showed great variation between snacks namely, doughnut (100%) > springroll (84%) > curry puff (45%). The overall findings indicate that the RPO-based snacks are highly acceptable and can be used to improve the dietary intake of provitamin A carotenoids of Malaysian Orang Asli children.

Detection of 5-hydroxymethylfurfural and furfural in the aerosol of electronic cigarettes.

PubMed

Soussy, Sarah; El-Hellani, Ahmad; Baalbaki, Rima; Salman, Rola; Shihadeh, Alan; Saliba, Najat A

2016-11-01

The wide availability of sweet flavours has been hypothesised as a factor in the popularity of electronic cigarette (ECIG), especially among youth. Saccharides, which are commonly used to impart a sweet flavour to ECIG liquids, thermally degrade to produce toxic compounds, like aldehydes and furans. This study investigates the formation of furanic compounds in aerosols when ECIG liquid solutions of varying sweetener concentrations are vaped under different power and puff duration. Liquids are prepared by mixing aqueous sucrose, glucose or sorbitol solutions to a 70/30 propylene glycol/glycerin solution. Aerosols are generated and trapped on filter pads using a commercially available ECIG operating at 4.3 and 10.8 W and 4 and 8 s puff duration. Extraction, elimination of matrix interference and quantification are achieved using novel solid phase extraction and gas chromatography tandem mass spectrometry methods (GC-MS). Well-resolved GC peaks of 5-hydroxymethylfurfural (HMF) and furfural (FA) are detected. Both HMF and FA are quantified in the aerosols of sweet-flavoured e-liquids under various vaping conditions. Levels of furan emissions are significantly correlated with electric power and sweetener concentration and not with puff duration. Unlike saccharides, the formation of HMF and FA from a sugar alcohol is negligible. The addition of sweeteners to ECIG liquids exposes ECIG user to furans, a toxic class of compounds. Under certain conditions, the per-puff yield of HMF and FA in ECIG emissions is comparable to values reported for combustible cigarettes. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Potential harmful health effects of inhaling nicotine-free shisha-pen vapor: a chemical risk assessment of the main components propylene glycol and glycerol.

PubMed

Kienhuis, Anne S; Soeteman-Hernandez, Lya G; Bos, Peter Mj; Cremers, Hans Wjm; Klerx, Walther N; Talhout, Reinskje

2015-01-01

A shisha-pen is an electronic cigarette variant that is advertised to mimic the taste of a water pipe, or shisha. The aim of this study was to assess the potential harmful health effects caused by inhaling the vapor of a nicotine-free shisha-pen. Gas chromatography analysis was performed to determine the major components in shisha-pen vapor. Risk assessment was performed using puff volumes of e-cigarettes and "normal" cigarettes and a 1-puff scenario (one-time exposure). The concentrations that reached the airways and lungs after using a shisha-pen were calculated and compared to data from published toxicity studies. The main components in shisha-pen vapor are propylene glycol and glycerol (54%/46%). One puff (50 to 70 mL) results in exposure of propylene glycol and glycerol of 430 to 603 mg/m(3) and 348 to 495 mg/m(3), respectively. These exposure concentrations were higher than the points of departure for airway irritation based on a human study (propylene glycol, mean concentration of 309 mg/m(3)) and a rat study (glycerol, no-observed adverse effect level of 165 mg/m(3)). Already after one puff of the shisha-pen, the concentrations of propylene glycol and glycerol are sufficiently high to potentially cause irritation of the airways. New products such as the shisha-pen should be detected and risks should be assessed to inform regulatory actions aimed at limiting potential harm that may be caused to consumers and protecting young people to take up smoking.

Eye retraction and rotation during Corvis ST 'air puff' intraocular pressure measurement and its quantitative analysis.

PubMed

Boszczyk, Agnieszka; Kasprzak, Henryk; Jóźwik, Agnieszka

2017-05-01

The aim of this study was to analyse the indentation and deformation of the corneal surface, as well as eye retraction, which occur during air puff intraocular pressure (IOP) measurement. A group of 10 subjects was examined using a non-contact Corvis ST tonometer, which records image sequences of corneas deformed by an air puff. Obtained images were processed numerically in order to extract information about corneal deformation, indentation and eyeball retraction. The time dependency of the apex deformation/eye retraction ratio and the curve of dependency between apex indentation and eye retraction take characteristic shapes for individual subjects. It was noticed that the eye globes tend to rotate towards the nose in response to the air blast during measurement. This means that the eye globe not only displaces but also rotates during retraction. Some new parameters describing the shape of this curve are introduced. Our data show that intraocular pressure and amplitude of corneal indentation are inversely related (r 8  = -0.83, P = 0.0029), but the correlation between intraocular pressure and amplitude of eye retraction is low and not significant (r 8  = -0.24, P = 0.51). The curves describing corneal behaviour during air puff tonometry were determined and show that the eye globe rotates towards the nose during measurement. In addition, eye retraction amplitudes may be related to elastic or viscoelastic properties of deeper structures in the eye or behind the eye and this should be further investigated. Many of the proposed new parameters present comparable or even higher repeatability than the standard parameters provided by the Corvis ST. © 2017 The Authors Ophthalmic & Physiological Optics © 2017 The College of Optometrists.

DUST AROUND R CORONAE BOREALIS STARS. I. SPITZER/INFRARED SPECTROGRAPH OBSERVATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anibal Garcia-Hernandez, D.; Kameswara Rao, N.; Lambert, David L., E-mail: agarcia@iac.es, E-mail: nkrao@iiap.res.in, E-mail: dll@astro.as.utexas.edu

2011-09-20

Spitzer/infrared spectrograph (IRS) spectra from 5 to 37 {mu}m for a complete sample of 31 R Coronae Borealis stars (RCBs) are presented. These spectra are combined with optical and near-infrared photometry of each RCB at maximum light to compile a spectral energy distribution (SED). The SEDs are fitted with blackbody flux distributions and estimates are made of the ratio of the infrared flux from circumstellar dust to the flux emitted by the star. Comparisons for 29 of the 31 stars are made with the Infrared Astronomical Satellite (IRAS) fluxes from three decades earlier: Spitzer and IRAS fluxes at 12 {mu}mmore » and 25 {mu}m are essentially equal for all but a minority of the sample. For this minority, the IRAS to Spitzer flux ratio exceeds a factor of three. The outliers are suggested to be stars where formation of a dust cloud or dust puff is a rare event. A single puff ejected prior to the IRAS observations may have been reobserved by Spitzer as a cooler puff at a greater distance from the RCB. RCBs which experience more frequent optical declines have, in general, a circumstellar environment containing puffs subtending a larger solid angle at the star and a quasi-constant infrared flux. Yet, the estimated subtended solid angles and the blackbody temperatures of the dust show a systematic evolution to lower solid angles and cooler temperatures in the interval between IRAS and Spitzer. Dust emission by these RCBs and those in the LMC is similar in terms of total 24 {mu}m luminosity and [8.0]-[24.0] color index.« less

Electronic Cigarette Nicotine Delivery Can Exceed that of Combustible Cigarettes: A Preliminary Report

PubMed Central

Ramôa, Carolina P.; Hiler, Marzena M.; Spindle, Tory R; Lopez, Alexa A.; Karaoghlanian, Nareg; Lipato, Thokozeni; Breland, Alison B.; Shihadeh, Alan; Eissenberg, Thomas

2016-01-01

Introduction Electronic cigarettes (ECIGs) aerosolize a liquid that usually contains propylene glycol and/or vegetable glycerin, flavorants, and the dependence-producing drug nicotine in various concentrations. This laboratory study examined the relationship between liquid nicotine concentration on plasma nicotine concentration and puffing behavior in experienced ECIG users. Methods Sixteen ECIG-experienced participants used a 3.3-Volt ECIG battery attached to a 1.5-Ohm dual-coil “cartomizer” loaded with 1 ml of a flavored propylene glycol/vegetable glycerin liquid to complete four sessions, at least 2 days apart, that differed by nicotine concentration (0, 8, 18, or 36 mg/ml). In each session, participants completed two 10-puff ECIG use bouts (30-sec puff interval) separated by 60 minutes. Venous blood was sampled to determine plasma nicotine concentration. Puff duration, volume, and average flow rate were measured. Results Immediately after bout 1, mean plasma nicotine concentration was 5.5 ng/ml (SD=7.7) for 0 mg/ml liquid, with significantly (p<0.05) higher mean concentrations observed for the 8 (mean=17.8 ng/ml, SD=14.6), 18 (mean=25.9 ng/ml, SD=17.5), and 36 mg/ml (mean=30.2 ng/ml; SD=20.0) concentrations; a similar pattern was observed for bout 2. For bout 1, at 36 mg/ml, the mean post- minus pre-bout difference was 24.1 ng/ml (SD=18.3). Puff topography data were consistent with previous results and revealed few reliable differences across conditions. Discussion This study demonstrates a relationship between ECIG liquid nicotine concentration and user plasma nicotine concentration in experienced ECIG users. Nicotine delivery from some ECIGs may exceed that of a combustible cigarette. The rationale for this higher level of nicotine delivery is uncertain. PMID:26324250

Initial puffing behaviors and subjective responses differ between an electronic nicotine delivery system and traditional cigarettes.

PubMed

Norton, Kaila J; June, Kristie M; O'Connor, Richard J

2014-01-01

Electronic nicotine delivery systems (ENDS) present an emerging issue for tobacco control and data on product use behaviors are limited. Participants (N = 38 enrolled; N = 16 compliant) completed three lab visits over 5 days and were asked to abstain from regular cigarettes for 72 hours in favor of ENDS (Smoke 51 TRIO - 3 piece, First Generation with 11 mg/ml filters). Lab visits included measurement of exhaled carbon monoxide (CO) and salivary cotinine concentration, questionnaire measures of regular cigarette craving after the 72 hour abstinence, and subjective product effects. Participants used a topography device to record puff volume, duration, flow rate, and inter-puff interval. Analyses revealed significant differences across products in puff count, average volume, total volume and inter-puff interval, with ENDS broadly showing a more intensive smoking pattern. Cigarette craving scores dropped significantly after smoking regular cigarettes, but not ENDS (p = .001), and subjective measures showed ENDS rated less favorably. CO boost, after ENDS use, decreased significantly (p < .001), and saliva cotinine significantly dropped between visits 1 and 3 (p < 0.001) after ENDS use relative to after cigarette smoking. For compliant and non-compliant participants, there was an average 82.0% [V1 - 16.1 cpd; V3 - 2.9 cpd] and average 73.9% [V1 - 20.3 cpd; V3 - 5.3 cpd] reduction in regular cigarette use per day during the ENDS trial period, respectively. The ENDS were smoked more intensively than own brand cigarettes, but delivered significantly less nicotineand were less satisfying. These findings have implications for the viability of certain ENDS as alternatives to cigarettes.

Self-titration by experienced e-cigarette users: blood nicotine delivery and subjective effects.

PubMed

Dawkins, Lynne E; Kimber, Catherine F; Doig, Mira; Feyerabend, Colin; Corcoran, Olivia

2016-08-01

Self-titration is well documented in the tobacco literature. The extent to which e-cigarette users (vapers) self-titrate is unknown. This study explored the effects of high and low nicotine strength liquid on puffing topography, nicotine delivery and subjective effects in experienced vapers. Eleven experienced male vapers completed 60 min of ad libitum vaping under low (6 mg/mL) and high (24 mg/mL) nicotine liquid conditions in two separate sessions. Measurements included puffing topography (puff number, puff duration, volume of liquid consumed) and changes in plasma nicotine levels, craving, withdrawal symptoms, self-reported hit, satisfaction and adverse effects. Liquid consumption and puff number were higher and puff duration longer, in the low nicotine strength condition (all ps < 0.01). The mean difference in nicotine boost from baseline in the low condition was 8.59 (7.52) ng/mL, 16.99 (11.72) ng/mL and 22.03 (16.19) ng/mL at 10, 30 and 60 min, respectively. Corresponding values for the high condition were 33.77 (34.88) ng/mL, 35.48 (28.31) ng/mL and 43.57 (34.78) ng/mL (ps < 0.05). There were no statistically significant differences between conditions in self-reported craving, withdrawal symptoms, satisfaction, hit or adverse effects. Vapers engaged in compensatory puffing with lower nicotine strength liquid, doubling their consumption. Whilst compensatory puffing was sufficient to reduce craving and withdrawal discomfort, self-titration was incomplete with significantly higher plasma nicotine levels in the high condition.

Behavior of accessory abducens and abducens motoneurons during eye retraction and rotation in the alert cat.

PubMed

Delgado-Garcia, J M; Evinger, C; Escudero, M; Baker, R

1990-08-01

1. The activity of both accessory abducens (Acc Abd) and abducens (Abd) motoneurons (Mns) was recorded in the alert cat during eye retraction and rotational eye movements. Cats were fitted with two scleral coils, one measured rotational eye movements directly and the other retraction by distinguishing the translational component. 2. Acc Abd and Abd Mns were identified following antidromic activation from electrical stimulation of the ipsilateral VIth nerve. 3. In response to corneal air puffs, bursts of spikes were produced in all (n = 30) Acc Abd Mns. The burst began 7.2 +/- 1.2 (SD) ms after onset of the air puff and 8.9 +/- 1.9 ms before eye retraction. 4. Acc Abd Mns were silent throughout all types of rotational eye movements, and tonic activity was not observed during intervals without air-puff stimulation. 5. In contrast, all (n = 50) identified Abd Mns exhibited a burst and/or pause in activity preceding and during horizontal saccades as well as a tonic activity proportional to eye position. 6. Only 10% of Abd Mns fired a weak burst of spikes in response to air-puff stimulation. 7. We conclude that Acc Abd Mns are exclusively involved in eye retraction in the cat and that only a few Abd Mns have an eye-retraction signal added to their eye position and velocity signals. Thus any rotational eye-movement response described in retractor bulbi muscle must result from innervation by Mns located in the Abd and/or the oculomotor nuclei. 8. The organization of the prenuclear circuitry and species variation are discussed in view of the nictiating membrane extension response measured in associative learning.

Incorporation of the NAG-FRAG Model for Ductile and Brittle Fracture into Help, a 2D Multimaterial Eulerian Program

DTIC Science & Technology

1978-09-01

Models HELP Ductile Material HEMP Brittle Material PUFF Iron Aluminum Eulerian Codea Tap«.r«»H Flyor Pl^«-» rmp«^» tO. ABITRACT (Conllmjm M r«v... HEMP ) code with those obtained by the Eulerian (HELP) code 5.3 Relative void volume of damage regions at three times after impact in the 1145...plate calculation 5.5 Relative void volume of material in the 1145 aluminum target at 1.46 us after impact as computed by the Lagrangian ( HEMP

An ambusher's arsenal: chemical crypsis in the puff adder (Bitis arietans)

PubMed Central

Miller, Ashadee Kay; Maritz, Bryan; McKay, Shannon; Glaudas, Xavier; Alexander, Graham J.

2015-01-01

Ambush foragers use a hunting strategy that places them at risk of predation by both visual and olfaction-oriented predators. Resulting selective pressures have driven the evolution of impressive visual crypsis in many ambushing species, and may have led to the development of chemical crypsis. However, unlike for visual crypsis, few studies have attempted to demonstrate chemical crypsis. Field observations of puff adders (Bitis arietans) going undetected by several scent-orientated predator and prey species led us to investigate chemical crypsis in this ambushing species. We trained dogs (Canis familiaris) and meerkats (Suricata suricatta) to test whether a canid and a herpestid predator could detect B. arietans using olfaction. We also tested for chemical crypsis in five species of active foraging snakes, predicted to be easily detectable. Dogs and meerkats unambiguously indicated active foraging species, but failed to correctly indicate puff adder, confirming that B. arietans employs chemical crypsis. This is the first demonstration of chemical crypsis anti-predatory behaviour, though the phenomenon may be widespread among ambushers, especially those that experience high mortality rates owing to predation. Our study provides additional evidence for the existence of an ongoing chemically mediated arms race between predator and prey species. PMID:26674950

Effect of the axial magnetic field on a metallic gas-puff pinch implosion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rousskikh, A. G.; Zhigalin, A. S.; Frolova, V.

2016-06-15

The effect of an axial magnetic field B{sub z} on an imploding metallic gas-puff Z-pinch was studied using 2D time-gated visible self-emission imaging. Experiments were performed on the IMRI-5 generator (450 kA, 450 ns). The ambient field B{sub z} was varied from 0.15 to 1.35 T. It was found that the initial density profile of a metallic gas-puff Z-pinch can be approximated by a power law. Time-gated images showed that the magneto-Rayleigh–Taylor instabilities were suppressed during the run-in phase both without axial magnetic field and with axial magnetic field. Helical instability structures were detected during the stagnation phase for B{sub z} < 1.1 T. For B{submore » z} = 1.35 T, the pinch plasma boundary was observed to be stable in both run-in and stagnation phases. When a magnetic field of 0.3 T was applied to the pinch, the soft x-ray energy was about twice that generated without axial magnetic field, mostly due to longer dwell time at stagnation.« less

A laboratory-based evaluation of exercise plus contingency management for reducing cigarette smoking.

PubMed

Kurti, Allison N; Dallery, Jesse

2014-11-01

Both contingency management (CM) and exercise have shown promise as smoking cessation treatments, but their combined effects have not been evaluated. The present study evaluated whether CM (in which motivational incentives are provided for abstinence) plus exercise reduced smoking more than either component alone. In a within-subjects design, 20 smokers were exposed to exercise plus CM, exercise plus CM-control (non-contingent incentives), inactivity plus CM, and inactivity plus CM-control. CM increased latencies to smoke and decreased total puffs (Mdns = 39.6 min and .8 puffs, respectively) relative to CM-control (Mdns = 2.5 min and 12.8 puffs). Exercise decreased craving relative to baseline for craving based on both the pleasurable consequences of smoking (D=-10.7 on a 100-point visual analog scale) and anticipated relief from withdrawal (D=-5.9), whereas inactivity increased both components of craving (Ds=7.6 and 3.5). Exercise had no effect on smoking or a measure of temporal discounting. Although exercise decreased craving, it did not affect smoking behavior. Exercise plus CM was not more effective than CM alone. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Smoking Behavior and Smoke Constituents from Cigarillos and Little Cigars

PubMed Central

Koszowski, Bartosz; Rosenberry, Zachary R.; Yi, Daniel; Stewart, Sean; Pickworth, Wallace B.

2017-01-01

Objective Although most cigarillos and little cigars smokers also smoke cigarettes (dual use), there are few studies comparing toxicant exposure and smoking behavior in cigars and cigarettes. Methods Two groups of dual users smoked their usual brand of cigarette and either a Winchester unflavored little cigar (N = 21) or a Black & Mild cigarillo (N = 23). Acute exposure of nicotine and exhaled carbon monoxide (CO) and puffing topography parameters were collected. Individual cigar puffing data were used to machine-replicate smoking for analysis of volatile organic compounds (VOC) and semi-volatile organic compounds (SVOC) in mainstream smoke. Results There were significant differences in puff topography, plasma nicotine and exhaled CO after cigarettes, little cigars, and cigarillos. Puff topography differences between cigarillos and cigarettes were due to the difference in the size of the article. Mainstream cigar and cigarette smoke was qualitatively similar; the yield was dependent on the smoking behavior. When smoke yield was adjusted for weight of tobacco burned or puff volume, exposure differences decreased. Conclusions There is a wide range of delivery of both SVOC and VOC components of cigar and cigarillo smoke. The difference in exposure is largely dependent on the article size and the amount consumed. PMID:28944278

An ambusher's arsenal: chemical crypsis in the puff adder (Bitis arietans).

PubMed

Miller, Ashadee Kay; Maritz, Bryan; McKay, Shannon; Glaudas, Xavier; Alexander, Graham J

2015-12-22

Ambush foragers use a hunting strategy that places them at risk of predation by both visual and olfaction-oriented predators. Resulting selective pressures have driven the evolution of impressive visual crypsis in many ambushing species, and may have led to the development of chemical crypsis. However, unlike for visual crypsis, few studies have attempted to demonstrate chemical crypsis. Field observations of puff adders (Bitis arietans) going undetected by several scent-orientated predator and prey species led us to investigate chemical crypsis in this ambushing species. We trained dogs (Canis familiaris) and meerkats (Suricata suricatta) to test whether a canid and a herpestid predator could detect B. arietans using olfaction. We also tested for chemical crypsis in five species of active foraging snakes, predicted to be easily detectable. Dogs and meerkats unambiguously indicated active foraging species, but failed to correctly indicate puff adder, confirming that B. arietans employs chemical crypsis. This is the first demonstration of chemical crypsis anti-predatory behaviour, though the phenomenon may be widespread among ambushers, especially those that experience high mortality rates owing to predation. Our study provides additional evidence for the existence of an ongoing chemically mediated arms race between predator and prey species. © 2015 The Author(s).

Assessment of nicotine concentration in electronic nicotine delivery system (ENDS) liquids and precision of dosing to aerosol.

PubMed

Kosmider, Leon; Sobczak, Andrzej; Szołtysek-Bołdys, Izabela; Prokopowicz, Adam; Skórka, Agnieszka; Abdulafeez, Oluyadi; Koszowski, Bartosz

2015-01-01

Global use of electronic nicotine delivery systems (ENDS; also called electronic cigarettes, e-cigarettes) has increased dramatically in recent years. However, due to the limited safety studies and growing concerns on the potential toxicity from long term use of ENDS, many national and international governments have employed regulatory measures to curtail its use. One of the most significant challenges regulators of ENDS encounter is the lack of quality standards to assess ENDS, e-liquid (solution used with ENDS which contain nicotine--a highly toxic and addictive substance), and amount of nicotine delivery to aerosol during ENDS use. Aims of the study were to (1) measure and compare nicotine concentration in e-liquids to values reported by manufacturers on packaging labels; (2) assess the precision of nicotine delivery from tank during aerosol formation. Methods: Nine popular Polish e-liquids (based on the market share data from October 2014) were purchased for the study. The labelled nicotine concentration for the selected e-liquids ranged between 11-25 mg/mL. All e-liquids were aerosolized in the laboratory using a smoking simulation machine (Palaczbot). Each e-liquid was aerosolized in a series of 6 consecutive bouts. A single bout consisted of 15 puffs with the following puff topography: 65 mL puff volume, 2.8 sec. puff duration, and 19 sec. interpuff interval. A total of 90 puffs were generated from each e-liquid. Nicotine content in the e-liquids and the aerosol generated were determined by gas chromatography with thermionic sensitive detection (GC-TSD). For seven of nine analyzed e-liquids, the difference between measured and manufacturer labeled nicotine concentration was less than 10%. Nicotine dose in aerosol per bout ranged between 0.77-1.49 mg (equivalent to one-half the nicotine a smoker inhales from a single combustible cigarette). Our analysis showed the high consistency between the labeled and measured nicotine concentration for popular on the Polish market ENDS e-liquids. Also, our analysis demonstrates that the risk for nicotine overdose is likely minimal when ENDS are used in a similar manner as a combustible cigarette. However, due to the toxicity risk nicotine poses regulatory measures focused on safety and quality of e-liquids should continually be exercised.

Group Waterpipe Tobacco Smoking Increases Smoke Toxicant Concentration

PubMed Central

Ramôa, Carolina P.; Shihadeh, Alan; Salman, Rola

2016-01-01

Abstract Introduction: Waterpipe tobacco smoking is a global health concern. Laboratory research has focused on individual waterpipe users while group use is common. This study examined user toxicant exposure and smoke toxicant yield associated with individual and group waterpipe smoking. Methods: Twenty-two pairs of waterpipe smokers used a waterpipe individually and as a dyad. Before and after smoking, blood was sampled and expired carbon monoxide (CO) measured; puff topography was recorded throughout. One participant from each pair was selected randomly and their plasma nicotine and expired air CO concentrations were compared when smoking alone to when smoking as part of a dyad. Recorded puff topography was used to machine-produce smoke that was analyzed for toxicant content. Results: There was no difference in mean plasma nicotine concentration when an individual smoked as part of a dyad (mean = 14.9ng/ml; standard error of the mean [ SEM ] = 3.0) compared to when smoking alone (mean = 10.0ng/ml; SEM = 1.5). An individual smoking as part of as a dyad had, on average, lower CO (mean = 15.8 ppm; SEM = 2.0) compared to when smoking alone (mean= 21.3 ppm; SEM = 2.7). When two participants smoked as a dyad they took, on average, more puffs (mean = 109.8; SEM = 7.6) than a singleton smoker (mean = 77.7; SEM = 8.1) and a shorter interpuff interval (IPI; dyad mean = 23.8 seconds; SEM = 1.9; singleton mean = 40.8 seconds; SEM = 4.8). Higher concentrations of several toxicants were observed in dyad-produced smoke. Discussion: Dyad smoking may increase smoke toxicant content, likely due to the dyad’s shorter IPIs and greater puff number. More work is needed to understand if group waterpipe smoking alters the health risks of waterpipe tobacco smoking. Implications: This study is the first to measure toxicants in smoke generated from a waterpipe when used by a dyad. Relative to smoke generated by a singleton, dyad smoke had higher concentration of some toxicants. These differences may be attributed to differences in puffing behavior, specifically the shorter IPI and greater puff number observed in the dyad condition. Relative to singleton smokers, dyad smokers were exposed to less CO, but nicotine exposure did not differ. More work is needed to assess the health effects of inhalation of more toxicant-laden smoke during group waterpipe use. PMID:26659913

Atmospheres of Two Super-Puffs: Transmission Spectra of Kepler 51b and Kepler 51d

NASA Astrophysics Data System (ADS)

Roberts, Jessica; Berta-Thompson, Zachory K.; Desert, Jean-Michel; Deck, Katherine; Fabrycky, Daniel; Fortney, Jonathan J.; Line, Michael R.; Lopez, Eric; Masuda, Kento; Morley, Caroline; Sanchis Ojeda, Roberto; Winn, Joshua N.

2018-06-01

The Kepler 51 system hosts three transiting, extremely low-mass, low-density exoplanets. These planets orbit a young G type star at periods of 45, 85 and 130 days, placing them outside of the regime for the inflated hot-Jupiters. Instead, the Kepler 51 planets are part of a rare class of exoplanets: the super-puffs. Models suggest these H/He-rich planets formed outside of the snow-line and migrated inwards, which might imply abundant water in their atmospheres. Because Kepler 51b and 51d have low surface gravities, they also have scale heights 10x larger than a typical hot-Jupiter, making them prime targets for atmospheric investigation. Kepler 51c, while also possessing a large scale height, only grazes its star during transit. We are also presented with a unique opportunity to study two super-puffs in very different temperature regimes around the same star. Therefore, we observed two transits each of both Kepler 51b and 51d with the Hubble Space Telescope’s Wide Field Camera 3 G141 grism spectroscopy. Using these data we created spectroscopic light curves that allow us to compute a transmission spectrum for each planet. We conclude that both planets have a flat transmission spectrum with a precision better than 0.6 scale heights between 1.1 and 1.7 microns. We also analyzed the transit timing variations of each planet by combining re-fitted Kepler mid-transit times with our measured HST times. From these additional timing points, we are able to better constrain the planetary masses and the dynamics of the system. With these updated masses and revisited stellar parameters, we determine precise measurements on the densities of these planets. We will present these results as well as discuss the implications for high altitude aerosols in both Kepler 51b and 51d.

Local plantar pressure relief in therapeutic footwear: design guidelines from finite element models.

PubMed

Erdemir, Ahmet; Saucerman, Jeffrey J; Lemmon, David; Loppnow, Bryan; Turso, Brie; Ulbrecht, Jan S; Cavanagh, Peter Re

2005-09-01

A major goal of therapeutic footwear in patients with pain or those at risk for skin injury is to relieve focal loading under prominent metatarsal heads. One frequent approach is to place plugs of compliant material into the midsole of the shoe. This study investigated 36 plug designs, a combination of three materials, six geometries, and two placements using a two-dimensional (2D) finite element model. Realistic loading conditions were obtained from plantar pressures (PP) recorded during walking in five subjects who wore control midsoles manufactured using Microcell Puff. Measured peak pressures underneath the second metatarsal head were similar to the results of the control model. PP obtained from simulations with the plugs built into a firm midsole were compared to the simulation results of the control midsole. Large plugs (e.g. 40 mm width), made out of Microcell Puff Lite or Plastazote Medium, placed at peak pressure sites, resulted in highest reductions in peak pressures (18-28%). Smaller plugs benefited from tapering when placed at high pressure areas. Case studies were completed on a healthy male subject and a diabetic female patient to address the efficacy of a plug design favored by our simulations (pressure based placement, 40 x 20 mm, Plastazote Medium). Successful reductions of second metatarsal head pressures were observed with a mediolateral load redistribution that was not represented by our model. 2D computer simulations allowed systematic investigation of plug properties without the need for high volume experimentation on human subjects and established basic guidelines for plug selection. In particular, plugs that are placed based on plantar pressure measurements were proven to be more effective when compared to those positioned according to the projection of the bony landmark on the foot-shoe plantar contact area.

A model-based method for estimating Ca2+ release fluxes from linescan images in Xenopus oocytes.

PubMed

Baran, Irina; Popescu, Anca

2009-09-01

We propose a model-based method of interpreting linescan images observed in Xenopus oocytes with the use of Oregon Green-1 as a fluorescent dye. We use a detailed modeling formalism based on numerical simulations that incorporate physical barriers for local diffusion, and, by assuming a Gaussian distribution of release durations, we derive the distributions of release Ca(2+) amounts and currents, fluorescence amplitudes, and puff widths. We analyze a wide set of available data collected from 857 and 281 events observed in the animal and the vegetal hemispheres of the oocyte, respectively. A relatively small fraction of events appear to involve coupling of two or three adjacent clusters of Ca(2+) releasing channels. In the animal hemisphere, the distribution of release currents with a mean of 1.4 pA presents a maximum at 1.0 pA and a rather long tail extending up to 5 pA. The overall distribution of liberated Ca(2+) amounts exhibits a dominant peak at 120 fC, a smaller peak at 375 fC, and an average of 166 fC. Ca(2+) amounts and release fluxes in the vegetal hemisphere appear to be 3.6 and 1.6 times smaller than in the animal hemisphere, respectively. Predicted diameters of elemental release sites are approximately 1.0 microm in the animal and approximately 0.5 microm in the vegetal hemisphere, but the side-to-side separation between adjacent sites appears to be identical (approximately 0.4 microm). By fitting the model to individual puffs we can estimate the quantity of liberated calcium, the release current, the orientation of the scan line, and the dimension of the corresponding release site.

Inverse identification of unknown finite-duration air pollutant release from a point source in urban environment

NASA Astrophysics Data System (ADS)

Kovalets, Ivan V.; Efthimiou, George C.; Andronopoulos, Spyros; Venetsanos, Alexander G.; Argyropoulos, Christos D.; Kakosimos, Konstantinos E.

2018-05-01

In this work, we present an inverse computational method for the identification of the location, start time, duration and quantity of emitted substance of an unknown air pollution source of finite time duration in an urban environment. We considered a problem of transient pollutant dispersion under stationary meteorological fields, which is a reasonable assumption for the assimilation of available concentration measurements within 1 h from the start of an incident. We optimized the calculation of the source-receptor function by developing a method which requires integrating as many backward adjoint equations as the available measurement stations. This resulted in high numerical efficiency of the method. The source parameters are computed by maximizing the correlation function of the simulated and observed concentrations. The method has been integrated into the CFD code ADREA-HF and it has been tested successfully by performing a series of source inversion runs using the data of 200 individual realizations of puff releases, previously generated in a wind tunnel experiment.

Menthol smokers: metabolomic profiling and smoking behavior

PubMed Central

Hsu, Ping-Ching; Lan, Renny S.; Brasky, Theodore M.; Marian, Catalin; Cheema, Amrita K.; Ressom, Habtom W.; Loffredo, Christopher A.; Pickworth, Wallace B.; Shields, Peter G.

2016-01-01

Background The use of menthol in cigarettes and marketing is under consideration for regulation by the FDA. However, the effects of menthol on smoking behavior and carcinogen exposure have been inconclusive. We previously reported metabolomic profiling for cigarette smokers, and novelly identified a menthol-glucuronide (MG) as the most significant metabolite directly related to smoking. Here, MG is studied in relation to smoking behavior and metabolomic profiles. Methods A cross-sectional study of 105 smokers who smoked two cigarettes in the laboratory one hour apart. Blood nicotine, MG and exhaled carbon monoxide (CO) boosts were determined (the difference before and after smoking). Spearman's correlation, Chi-Square and ANCOVA adjusted for gender, race and cotinine levels for menthol smokers assessed the relationship of MG boost, smoking behavior, and metabolic profiles. Multivariate metabolite characterization using supervised Partial Least Squares-Discriminant Analysis (PLS-DA) was carried out for the classification of metabolomics profiles. Results MG boost was positively correlated with CO boost, nicotine boost, average puff volume, puff duration, and total smoke exposure. Classification using PLS-DA, MG was the top metabolite discriminating metabolome of menthol vs. non-menthol smokers. Among menthol smokers, forty-two metabolites were significantly correlated with MG boost, which linked to cellular functions such as of cell death, survival, and movement. Conclusion Plasma MG boost is a new smoking behavior biomarker that may provides novel information over self-reported use of menthol cigarettes by integrating different smoking measures for understanding smoking behavior and harm of menthol cigarettes. Impacts These results provide insight into the biological effect of menthol smoking. PMID:27628308

OEDGE modeling of plasma contamination efficiency of Ar puffing from different divertor locations in EAST

NASA Astrophysics Data System (ADS)

Pengfei, ZHANG; Ling, ZHANG; Zhenwei, WU; Zong, XU; Wei, GAO; Liang, WANG; Qingquan, YANG; Jichan, XU; Jianbin, LIU; Hao, QU; Yong, LIU; Juan, HUANG; Chengrui, WU; Yumei, HOU; Zhao, JIN; J, D. ELDER; Houyang, GUO

2018-04-01

Modeling with OEDGE was carried out to assess the initial and long-term plasma contamination efficiency of Ar puffing from different divertor locations, i.e. the inner divertor, the outer divertor and the dome, in the EAST superconducting tokamak for typical ohmic plasma conditions. It was found that the initial Ar contamination efficiency is dependent on the local plasma conditions at the different gas puff locations. However, it quickly approaches a similar steady state value for Ar recycling efficiency >0.9. OEDGE modeling shows that the final equilibrium Ar contamination efficiency is significantly lower for the more closed lower divertor than that for the upper divertor.

An Exploratory Human Laboratory Experiment Evaluating Vaporized Cannabis in the Treatment of Neuropathic Pain from Spinal Cord Injury and Disease

PubMed Central

Wilsey, Barth; Marcotte, Thomas D.; Deutsch, Reena; Zhao, Holly; Prasad, Hannah; Phan, Amy

2016-01-01

Using eight hour human laboratory experiments, we evaluated the analgesic efficacy of vaporized cannabis in patients with neuropathic pain related to injury or disease of the spinal cord, the majority of whom were experiencing pain despite traditional treatment. After obtaining baseline data, 42 participants underwent a standardized procedure for inhaling 4 puffs of vaporized cannabis containing either placebo, 2.9%, or 6.7% delta-9-tetrahydrocannabinol on three separate occasions. A second dosing occurred 3 hours later; participants chose to inhale 4 to 8 puffs. This flexible dosing was utilized to attempt to reduce the placebo effect. Using an 11-point numerical pain intensity rating scale as the primary outcome, a mixed effects linear regression model demonstrated a significant analgesic response for vaporized cannabis. When subjective and psychoactive side effects (e.g., good drug effect, feeling high, etc.) were added as covariates to the model, the reduction in pain intensity remained significant above and beyond any effect of these measures (all p<0.0004). Psychoactive and subjective effects were dose dependent. Measurement of neuropsychological performance proved challenging because of various disabilities in the population studied. As the two active doses did not significantly differ from each other in terms of analgesic potency, the lower dose appears to offer the best risk-benefit ratio in patients with neuropathic pain associated with injury or disease of the spinal cord. PMID:27286745

The case for investigating social context in laboratory studies of smoking.

PubMed

Dimoff, John D; Sayette, Michael A

2017-03-01

With increasing frequency, addiction is conceived of as a brain disease, and such accounts seem especially pertinent with regard to the rapid delivery of nicotine to the brain via cigarette smoke. Moreover, drug administration trials (cigarette puffs) suggest that the behavior of smoking becomes automatized, with individuals developing prototypical approaches to smoking a cigarette. Compared with presumably more social activities, such as drinking alcohol, there may be little opportunity for social processes to influence smoking behavior. However, survey research examining smoking motivation often reveals a broadly defined 'social' factor and field research suggests that social context does influence smoking. We posit that laboratory smoking research has largely ignored social contextual factors that may help to understand better the precise mechanisms underlying smoking behavior and smoking motivation. We reviewed laboratory studies examining the effect of social context (operationalized as modeling) on smoking behavior. Studies were identified by searching PsychInfo and Medline using the following keywords: smoking, nicotine, tobacco, cigarette, consumption, topography, puff, smoking behavior, cigarettes smoked, modeling, imitation, social context, social influence and peer pressure. The reference and citation lists of these studies were then searched to identify additional studies. Few laboratory smoking studies target social context. Those few studies indicate that smoking behavior can be influenced by the presence of others. There is also some evidence that social context influences the effects of smoking as well as processes related to self-perception and self-regulation that reinforce smoking and hamper smoking cessation efforts. © 2016 Society for the Study of Addiction.

Applications of the PUFF model to forecasts of volcanic clouds dispersal from Etna and Vesuvio

NASA Astrophysics Data System (ADS)

Daniele, P.; Lirer, L.; Petrosino, P.; Spinelli, N.; Peterson, R.

2009-05-01

PUFF is a numerical volcanic ash tracking model developed to simulate the behaviour of ash clouds in the atmosphere. The model uses wind field data provided by meteorological models and adds dispersion and sedimentation physics to predict the evolution of the cloud once it reaches thermodynamic equilibrium with the atmosphere. The software is intended for use in emergency response situations during an eruption to quickly forecast the position and trajectory of the ash cloud in the near (˜1-72 h) future. In this paper, we describe the first application of the PUFF model in forecasting volcanic ash dispersion from the Etna and Vesuvio volcanoes. We simulated the daily occurrence of an eruptive event of Etna utilizing ash cloud parameters describing the paroxysm of 22nd July 1998 and wind field data for the 1st September 2005-31st December 2005 time span from the Global Forecast System (GFS) model at the approximate location of the Etna volcano (38N 15E). The results show that volcanic ash particles are dispersed in a range of directions in response to changing wind field at various altitudes and that the ash clouds are mainly dispersed toward the east and southeast, although the exact trajectory is highly variable, and can change within a few hours. We tested the sensitivity of the model to the mean particle grain size and found that an increased concentration of ash particles in the atmosphere results when the mean grain size is decreased. Similarly, a dramatic variation in dispersion results when the logarithmic standard deviation of the particle-size distribution is changed. Additionally, we simulated the occurrence of an eruptive event at both Etna and Vesuvio, using the same parameters describing the initial volcanic plume, and wind field data recorded for 1st September 2005, at approximately 38N 15E for Etna and 41N 14E for Vesuvio. The comparison of the two simulations indicates that identical eruptions occurring at the same time at the two volcanic centres display significantly different dispersal axes as a consequence of the different local wind field acting at the respective eruptive vents. At the Vesuvio the volcano, a plinian eruptive event with the dynamical parameters of the 79 A.D. eruption was simulated daily for one year, from 1st July 2005 to 30th June 2006. The statistical processing of results points out that, although in most cases the ash cloud dispersal encompasses many different areas, generally the easterly southeasterly direction is preferred. Our results highlight the significant role of wind field trends in influencing the distribution of ash particles from eruptive columns and prove that the dynamical parameters that most influence the variability of plume dispersal are the duration of the eruption and the maximum column height. Finally, the possible use of cloud simulations for refining hazard maps of areas exposed to volcanic ash dispersal is proposed.

A Model of Airflow and Diffusion in Complex Terrain (MADICT).

DTIC Science & Technology

1985-11-01

104 , 784-792. Ludwig, F.L. 1982: "Effect of a Change in Atmospheric Stability on the Growth Rate of Puffs Used in Plume Simulation Models," J. Appl...INPUTS C IF (NOPUF.EQ.0)THEN DO 2305 K=1, NFUNCT DOTX (1, K) =DOTX (0, K) 2305 CONTINUE IHOUR=N I-IHOUR+1)NOPUF=NOPUFF +1 ""- END IF RETURN END 104 ...CM) C DO 100 IX-0,INDX DO 100 IY0.,INDY RHB (IXIyl)I = (XRuAS (IXIY’l MTIN /10.0 RHS1 (IX, IY 2)= (XCR1S (IX, IY, 2) -Z4IN /100. 0 IF(RHS (IXI,2

Temperature Dependence of IP3-Mediated Local and Global Ca2+ Signals

PubMed Central

Dickinson, George D.; Parker, Ian

2013-01-01

We examined the effect of temperature (12–40°C) on local and global Ca2+ signals mediated by inositol trisphosphate receptor/channels (IP3R) in human neuroblastoma (SH-SY5Y) cells. The amplitudes and spatial spread of local signals arising from single IP3R (blips) and clusters of IP3R (puffs) showed little temperature dependence, whereas their kinetics (durations and latencies) were markedly accelerated by increasing temperature. In contrast, the amplitude of global Ca2+ waves increased appreciably at lower temperatures, probably as a result of the longer duration of IP3R channel opening. Several parameters, including puff and blip durations, puff latency and frequency, and frequency of repetitive Ca2+ waves, showed a biphasic temperature dependence on Arrhenius plots. In all cases the transition temperature occurred at ∼25°C, possibly reflecting a phase transition in the lipids of the endoplasmic reticulum membrane. Although the IP3-evoked Ca2+ signals were qualitatively similar at 25°C and 36°C, one should consider the temperature sensitivity of IP3-mediated signal amplitudes when extrapolating from room temperature to physiological temperature. Conversely, further cooling may be advantageous to improve the optical resolution of channel gating kinetics. PMID:23442860

Pulsed Turbulent Diffusion Flames in a Coflow

NASA Astrophysics Data System (ADS)

Usowicz, James E.; Hermanson, James C.; Johari, Hamid

2000-11-01

Fully modulated diffusion flames were studied experimentally in a co-flow combustor using unheated ethylene fuel at atmospheric pressure. A fast solenoid valve was used to fully modulate (completely shut-off) the fuel flow. The fuel was released from a 2 mm diameter nozzle with injection times ranging from 2 to 750 ms. The jet exit Reynolds number was 2000 to 10,000 with a co-flow air velocity of up to 0.02 times the jet exit velocity. Establishing the effects of co-flow for the small nozzle and short injection times is required for future tests of pulsed flames under microgravity conditions. The very short injection times resulted in compact, burning puffs. The compact puffs had a mean flame length as little as 20flame for the same Reynolds number. As the injection time and fuel volume increased, elongated flames resembling starting jets resulted with a flame length comparable to that of a steady flame. For short injection times, the addition of an air co-flow resulted in an increase in flame length of nearly 50flames with longer injection times was correspondingly smaller. The effects of interaction of successive pulses on the flame length were most pronounced for the compact puffs. The emissions of unburned hydrocarbon and NOx from the pulsed flames were examined.

Recovery of gonadal development in tiger puffer Takifugu rubripes after exposure to 17β-estradiol during early life stages

NASA Astrophysics Data System (ADS)

Hu, Peng; Liu, Bin; Meng, Zhen; Liu, Xinfu; Jia, Yudong; Yang, Zhi; Lei, Jilin

2017-05-01

The aim of the present study was to investigate the long-term effects of 17β-estradiol (E2) exposure on gonadal development in the tiger puff er ( Takifugu rubripes), which has a genetic sex determination system of male homogametic XY-XX. Tiger puff er larvae were exposed to 1, 10 and 100 μg/L E2 from 15 to 100 days post-hatch (dph) and then maintained in clean seawater until 400 dph. Changes in sex ratio, gonadal structure and gonadosomatic index (GSI) were monitored at 100, 160, 270 and 400 dph. Sex-associated single nucleotide polymorphism (SNP) markers were used to analyze the genetic sex of samples, except those at 100 dph. Exposure had a positive effect on the conversion of genetically male gonads into phenotypically female gonads at 100 dph. However, gonads from 60% of genetic XY males in the 1-μg/L E2 group and 100% in the 10-μg/L E2 group developed intersexual gonads at 160 dph; gonads of all genetic XY males in the two treatment groups reverted to testis by 270 dph. While 38%, 57% and 44% of gonads of XY fish in the 100-μg/L E2 group reverted to intersexual gonads at 160, 270 and 400 dph, respectively, none reverted to testis after E2 treatment. In addition, E2 exposure inhibited gonadal growth of both genetic sexes, as indicated by the clear dose-dependent decrease in GSI at 270 and 400 dph. The results showed that exposure to E2 during the early life stages of tiger puff er disrupted gonadal development, but that fish recovered after migration to clean seawater. The study suggests the potential use of tiger puff er as a valuable indicator species to evaluate the effects of environmental estrogens on marine fish, thereby protecting valuable fishery resources.

First Argon Gas Puff Experiments With 500 ns Implosion Time On Sphinx Driver

NASA Astrophysics Data System (ADS)

Zucchini, F.; Calamy, H.; Lassalle, F.; Loyen, A.; Maury, P.; Grunenwald, J.; Georges, A.; Morell, A.; Bedoch, J.-P.; Ritter, S.; Combes, P.; Smaniotto, O.; Lample, R.; Coleman, P. L.; Krishnan, M.

2009-01-01

Experiments have been performed at the SPHINX driver to study potential of an Argon Gas Puff load designed by AASC. We present here the gas Puff hardware and results of the last shot series. The Argon Gas Puff load used is injected thanks to a 20 cm diameter nozzle. The nozzle has two annuli and a central jet. The pressure and gas type in each of the nozzle plena can be independently adjusted to tailor the initial gaz density distribution. This latter is selected as to obtain an increasing radial density from outer shell towards the pinch axis in order to mitigate the RT instabilities and to increase radiating mass on axis. A flashboard unit produces a high intensity UV source to pre-ionize the Argon gas. Typical dimensions of the load are 200 mm in diameter and 40 mm height. Pressures are adjusted to obtain an implosion time around 550 ns with a peak current of 3.5 MA. With the goal of improving k-shell yield a mass scan of the central jet was performed and implosion time, mainly given by outer and middle plena settings, was kept constant. Tests were also done to reduce the implosion time for two configurations of the central jet. Strong zippering of the radiation production was observed mainly due to the divergence of the central jet over the 40 mm of the load height. Due to that feature k-shell radiation is mainly obtained near cathode. Therefore tests were done to mitigate this effect first by adjusting local pressure of middle and central jet and second by shortening the pinch length. At the end of this series, best shot gave 5 kJ of Ar k-shell yield. PCD detectors showed that k-shell x-ray power was 670 GW with a FWHM of less than 10 ns.

Breeding Super-Earths and Birthing Super-puffs in Transitional Disks

NASA Astrophysics Data System (ADS)

Lee, Eve J.; Chiang, Eugene

2016-02-01

The riddle posed by super-Earths (1-4R⊕, 2-20M⊕) is that they are not Jupiters: their core masses are large enough to trigger runaway gas accretion, yet somehow super-Earths accreted atmospheres that weigh only a few percent of their total mass. We show that this puzzle is solved if super-Earths formed late, as the last vestiges of their parent gas disks were about to clear. This scenario would seem to present fine-tuning problems, but we show that there are none. Ambient gas densities can span many (in one case up to 9) orders of magnitude, and super-Earths can still robustly emerge after ˜0.1-1 Myr with percent-by-weight atmospheres. Super-Earth cores are naturally bred in gas-poor environments where gas dynamical friction has weakened sufficiently to allow constituent protocores to gravitationally stir one another and merge. So little gas is present at the time of core assembly that cores hardly migrate by disk torques: formation of super-Earths can be in situ. The basic picture—that close-in super-Earths form in a gas-poor (but not gas-empty) inner disk, fed continuously by gas that bleeds inward from a more massive outer disk—recalls the largely evacuated but still accreting inner cavities of transitional protoplanetary disks. We also address the inverse problem presented by super-puffs: an uncommon class of short-period planets seemingly too voluminous for their small masses (4-10R⊕, 2-6M⊕). Super-puffs most easily acquire their thick atmospheres as dust-free, rapidly cooling worlds outside ˜1 AU where nebular gas is colder, less dense, and therefore less opaque. Unlike super-Earths, which can form in situ, super-puffs probably migrated in to their current orbits; they are expected to form the outer links of mean-motion resonant chains, and to exhibit greater water content. We close by confronting observations and itemizing remaining questions.

Determination of Chemical Compounds Generated from Second-generation E-cigarettes Using a Sorbent Cartridge Followed by a Two-step Elution Method.

PubMed

Uchiyama, Shigehisa; Senoo, Yui; Hayashida, Hideki; Inaba, Yohei; Nakagome, Hideki; Kunugita, Naoki

2016-01-01

We developed an analytical method for analyzing electronic cigarette (E-cigarette) smoke, and measured the carbonyl compounds and volatile organic compounds generated by 10 brands of second-generation E-cigarettes. A glass filter (Cambridge filter pad) for particulate matter and a solid sorbent tube packed with Carboxen-572 for gaseous compounds were used to collect E-cigarette smoke. These were then analyzed using a two-step elution method with carbon disulfide and methanol, followed by high-performance liquid chromatography (HPLC) and gas chromatography mass spectrometry (GC/MS). Formaldehyde (FA), acetaldehyde (AA), acetone (AC), acrolein (ACR), propanal (PA), acetol (AT), glyoxal (GO), and methyl glyoxal (MGO) were detected by HPLC in some E-cigarettes. Propylene glycol (PG), glycerol (GLY), and some esters were detected by GC/MS. GO and MGO exist mainly as particulate matter. AA, AC, ACR, PA, and AT exist mainly as gaseous compounds. FA exists as both particulate matter and gaseous compounds. These carbonyl compounds have carbon numbers C1 - C3. The main components of E-liquid are PG (C3) and GLY (C3). Therefore, the oxidation of liquids, such as PG and GLY in E-cigarettes upon incidental contact with the heating element in E-cigarette, is suggested as being a possible cause for carbonyl generation. When the puff number exceeds a critical point, carbonyl generation rapidly increases and then remains constant. The results of this study are now being used to determine the following E-cigarette smoking protocol: puff volume, 55 mL; puff duration, 2 s; and puff number, 30. E-cigarette analysis revealed very large variation in carbonyl concentration among not only different brands, but also different samples of the same product. Typical distributions of carbonyl concentration were not observed in any of the E-cigarettes tested, and the mean values greatly differed from median values.

Formulation and Evaluation of Long Circulating Liposomal Amphotericin B: A Scinti-kinetic Study using 99mTc in BALB/C Mice

PubMed Central

Jadhav, M. P.; Nagarsenker, Mangal S.; Gaikwad, R. V.; Samad, A.; Kshirsagar, Nilima A.

2011-01-01

In the present study, we formulated long circulating liposomes for amphotericin B and characterized them. The formulation was optimized using 23 factorial designs. Pegylated liposomal formulation showed favorable results with reference to particle size (247.33±9.60 nm), percent entrapment efficiency (94.55±3.34%). TEM studies revealed that the liposomes were essentially spherical, hollow, and appeared like powder puff structures. From DSC study it was concluded that the pegylated formulation containing Amp B showed better stability and membrane integrity of the formulation. During the stability studies the formulation was found to be stable. When subjected to gamma scintigraphy kinetic tracer studies the formulation showed longer residence time in the blood in BALB/C mice. PMID:22131622

Group Waterpipe Tobacco Smoking Increases Smoke Toxicant Concentration.

PubMed

Ramôa, Carolina P; Shihadeh, Alan; Salman, Rola; Eissenberg, Thomas

2016-05-01

Waterpipe tobacco smoking is a global health concern. Laboratory research has focused on individual waterpipe users while group use is common. This study examined user toxicant exposure and smoke toxicant yield associated with individual and group waterpipe smoking. Twenty-two pairs of waterpipe smokers used a waterpipe individually and as a dyad. Before and after smoking, blood was sampled and expired carbon monoxide (CO) measured; puff topography was recorded throughout. One participant from each pair was selected randomly and their plasma nicotine and expired air CO concentrations were compared when smoking alone to when smoking as part of a dyad. Recorded puff topography was used to machine-produce smoke that was analyzed for toxicant content. There was no difference in mean plasma nicotine concentration when an individual smoked as part of a dyad (mean = 14.9 ng/ml; standard error of the mean [SEM] = 3.0) compared to when smoking alone (mean = 10.0 ng/ml; SEM = 1.5). An individual smoking as part of as a dyad had, on average, lower CO (mean = 15.8 ppm; SEM = 2.0) compared to when smoking alone (mean= 21.3 ppm; SEM = 2.7). When two participants smoked as a dyad they took, on average, more puffs (mean = 109.8; SEM = 7.6) than a singleton smoker (mean = 77.7; SEM = 8.1) and a shorter interpuff interval (IPI; dyad mean = 23.8 seconds; SEM = 1.9; singleton mean = 40.8 seconds; SEM = 4.8). Higher concentrations of several toxicants were observed in dyad-produced smoke. Dyad smoking may increase smoke toxicant content, likely due to the dyad's shorter IPIs and greater puff number. More work is needed to understand if group waterpipe smoking alters the health risks of waterpipe tobacco smoking. This study is the first to measure toxicants in smoke generated from a waterpipe when used by a dyad. Relative to smoke generated by a singleton, dyad smoke had higher concentration of some toxicants. These differences may be attributed to differences in puffing behavior, specifically the shorter IPI and greater puff number observed in the dyad condition. Relative to singleton smokers, dyad smokers were exposed to less CO, but nicotine exposure did not differ. More work is needed to assess the health effects of inhalation of more toxicant-laden smoke during group waterpipe use. © The Author 2015. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Current distribution measurements inside an electromagnetic plasma gun operated in a gas-puff mode.

PubMed

Poehlmann, Flavio R; Cappelli, Mark A; Rieker, Gregory B

2010-12-01

Measurements are presented of the time-dependent current distribution inside a coaxial electromagnetic plasma gun. The measurements are carried out using an array of six axially distributed dual-Rogowski coils in a balanced circuit configuration. The radial current distributions indicate that operation in the gas-puff mode, i.e., the mode in which the electrode voltage is applied before injection of the gas, results in a stationary ionization front consistent with the presence of a plasma deflagration. The effects of varying the bank capacitance, transmission line inductance, and applied electrode voltage were studied over the range from 14 to 112 μF, 50 to 200 nH, and 1 to 3 kV, respectively.

Current distribution measurements inside an electromagnetic plasma gun operated in a gas-puff mode

PubMed Central

Poehlmann, Flavio R.; Cappelli, Mark A.; Rieker, Gregory B.

2010-01-01

Measurements are presented of the time-dependent current distribution inside a coaxial electromagnetic plasma gun. The measurements are carried out using an array of six axially distributed dual-Rogowski coils in a balanced circuit configuration. The radial current distributions indicate that operation in the gas-puff mode, i.e., the mode in which the electrode voltage is applied before injection of the gas, results in a stationary ionization front consistent with the presence of a plasma deflagration. The effects of varying the bank capacitance, transmission line inductance, and applied electrode voltage were studied over the range from 14 to 112 μF, 50 to 200 nH, and 1 to 3 kV, respectively. PMID:21267082

Comparison of simulation and experimental results for a gas puff nozzle on Ambiorix

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnier, J-N.; Chevalier, J-M.; Dubroca, B.

One of source term of Z-Pinch experiments is the gas puff density profile. In order to characterize the gas jet, an experiment based on interferometry has been performed. The first study was a point measurement (a section density profile) which led us to develop a global and instantaneous interferometry imaging method. In order to optimise the nozzle, we simulated the experiment with a flow calculation code (ARES). In this paper, the experimental results are compared with simulations. The different gas properties (He, Ne, Ar) and the flow duration lead us to take care, on the one hand, of the gasmore » viscosity, and on the other, of modifying the code for an instationary flow.« less

Development and application of a reactive plume-in-grid model: evaluation over Greater Paris

NASA Astrophysics Data System (ADS)

Korsakissok, I.; Mallet, V.

2010-09-01

Emissions from major point sources are badly represented by classical Eulerian models. An overestimation of the horizontal plume dilution, a bad representation of the vertical diffusion as well as an incorrect estimate of the chemical reaction rates are the main limitations of such models in the vicinity of major point sources. The plume-in-grid method is a multiscale modeling technique that couples a local-scale Gaussian puff model with an Eulerian model in order to better represent these emissions. We present the plume-in-grid model developed in the air quality modeling system Polyphemus, with full gaseous chemistry. The model is evaluated on the metropolitan Île-de-France region, during six months (summer 2001). The subgrid-scale treatment is used for 89 major point sources, a selection based on the emission rates of NOx and SO2. Results with and without the subgrid treatment of point emissions are compared, and their performance by comparison to the observations on measurement stations is assessed. A sensitivity study is also carried out, on several local-scale parameters as well as on the vertical diffusion within the urban area. Primary pollutants are shown to be the most impacted by the plume-in-grid treatment. SO2 is the most impacted pollutant, since the point sources account for an important part of the total SO2 emissions, whereas NOx emissions are mostly due to traffic. The spatial impact of the subgrid treatment is localized in the vicinity of the sources, especially for reactive species (NOx and O3). Ozone is mostly sensitive to the time step between two puff emissions which influences the in-plume chemical reactions, whereas the almost-passive species SO2 is more sensitive to the injection time, which determines the duration of the subgrid-scale treatment. Future developments include an extension to handle aerosol chemistry, and an application to the modeling of line sources in order to use the subgrid treatment with road emissions. The latter is expected to lead to more striking results, due to the importance of traffic emissions for the pollutants of interest.

Evaluation of two pollutant dispersion models over continental scales

NASA Astrophysics Data System (ADS)

Rodriguez, D.; Walker, H.; Klepikova, N.; Kostrikov, A.; Zhuk, Y.

Two long-range, emergency response models—one based on the particle-in-cell method of pollutant representation (ADPIC/U.S.) the other based on the superposition of Gaussian puffs released periodically in time (EXPRESS/Russia)—are evaluated using perfluorocarbon tracer data from the Across North America Tracer Experiment (ANATEX). The purpose of the study is to assess our current capabilities for simulating continental-scale dispersion processes and to use these assessments as a means to improve our modeling tools. The criteria for judging model performance are based on protocols devised by the Environmental Protection Agency and on other complementary tests. Most of these measures require the formation and analysis of surface concentration footprints (the surface manifestations of tracer clouds, which are sampled over 24-h intervals), whose dimensions, center-of-mass coordinates and integral characteristics provide a basis for comparing observed and calculated concentration distributions. Generally speaking, the plumes associated with the 20 releases of perfluorocarbon (10 each from sources at Glasgow, MT and St. Cloud, MN) in January 1987, are poorly resolved by the sampling network when the source-to-receptor distances are less than about 1000 km. Within this undersampled region, both models chronically overpredict the sampler concentrations. Given this tendency, the computed areas of the surface footprints and their integral concentrations are likewise excessive. When the actual plumes spread out sufficiently for reasonable resolution, the observed ( O) and calculated ( C) footprint areas are usually within a factor of two of one another, thereby suggesting that the models possess some skill in the prediction of long-range diffusion. Deviations in the O and C plume trajectories, as measured by the distances of separation between the plume centroids, are on the other of 125 km d -1 for both models. It appears that the inability of the models to simulate large-scale vertical motions and, more generally, to adequately characterize the meso- and macro-scale flows (mainly as the result of constraints imposed by the temporal and spatial resolution of the rawinsonde network) are major impediments to improved accuracy.

The structural genes for three Drosophila glue proteins reside at a single polytene chromosome puff locus.

PubMed Central

Crowley, T E; Bond, M W; Meyerowitz, E M

1983-01-01

The polytene chromosome puff at 68C on the Drosophila melanogaster third chromosome is thought from genetic experiments to contain the structural gene for one of the secreted salivary gland glue polypeptides, sgs-3. Previous work has demonstrated that the DNA included in this puff contains sequences that are transcribed to give three different polyadenylated RNAs that are abundant in third-larval-instar salivary glands. These have been called the group II, group III, and group IV RNAs. In the experiments reported here, we used the nucleotide sequence of the DNA coding for these RNAs to predict some of the physical and chemical properties expected of their protein products, including molecular weight, amino acid composition, and amino acid sequence. Salivary gland polypeptides with molecular weights similar to those expected for the 68C RNA translation products, and with the expected degree of incorporation of different radioactive amino acids, were purified. These proteins were shown by amino acid sequencing to correspond to the protein products of the 68C RNAs. It was further shown that each of these proteins is a part of the secreted salivary gland glue: the group IV RNA codes for the previously described sgs-3, whereas the group II and III RNAs code for the newly identified glue polypeptides sgs-8 and sgs-7. Images PMID:6406838

Time-resolved analysis of the emission of sidestream smoke (SSS) from cigarettes during smoking by photo ionisation/time-of-flight mass spectrometry (PI-TOFMS): towards a better description of environmental tobacco smoke.

PubMed

Streibel, T; Mitschke, S; Adam, T; Zimmermann, R

2013-09-01

In this study, the chemical composition of sidestream smoke (SSS) emissions of cigarettes are characterised using a laser-based single-photon ionisation time-of-flight mass spectrometer. SSS is generated from various cigarette types (2R4F research cigarette; Burley, Oriental and Virginia single-tobacco-type cigarettes) smoked on a single-port smoking machine and collected using a so-called fishtail chimney device. Using this setup, a puff-resolved quantification of several SSS components was performed. Investigations of the dynamics of SSS emissions show that concentration profiles of various substances can be categorised into several groups, either depending on the occurrence of a puff or uninfluenced by the changes in the burning zone during puffing. The SSS emissions occurring directly after a puff strongly resemble the composition of mainstream smoke (MSS). In the smouldering phase, clear differences between MSS and SSS are observed. The changed chemical profiles of SSS and MSS might be also of importance on environmental tobacco smoke which is largely determined by SSS. Additionally, the chemical composition of the SSS is strongly affected by the tobacco type. Hence, the higher nitrogen content of Burley tobacco leads to the detection of increased amounts of nitrogen-containing substances in SSS.

Acceleration of Hydrogen Ions up to 30 MeV and Generation of 3 × 1012 Neutrons in Megaampere Deuterium Gas-Puff Z-Pinch

NASA Astrophysics Data System (ADS)

Klir, D.; Cikhardt, J.; Kravarik, J.; Kubes, P.; Rezac, K.; Sila, O.; Shishlov, A.; Cherdizov, R.; Fursov, F.; Kokshenev, V.; Kovalchuk, B.; Kurmaev, N.; Labetsky, A.; Ratakhin, N.; Orcikova, H.; Turek, K.

2013-10-01

Fusion neutrons were produced with a deuterium gas-puff z-pinch on the GIT-12 generator at the Institute of High Current Electronics in Tomsk. The peak neutron yield from DD reactions reached Yn = (2 . 9 +/- 0 . 3) ×1012 at 100 μg/cm linear mass density of deuterium, 700 ns implosion time and 2.7 MA current. Such a neutron yield means that the scaling law of deuterium z-pinches Yn ~I4 was extended to 3 MA currents. The further increase of neutron yields up to (3 . 7 +/- 0 . 4) ×1012 was achieved by placing a deuterated polyethylene catcher onto the axis. Maximum neutron energies of 15 and 22 MeV were observed by radial and axial nToF detectors, respectively. A stack of CR-39 track detectors showed up to 40 MeV deuterons (or 30 MeV protons) on the z-pinch axis. Since the energy input into plasmas was 70 kJ, the number of DD neutrons per one joule of stored plasma energy exceeded the value of 5 ×107 . This value implies that deuterium gas-puff z-pinches belong to the most efficient plasma-based sources of DD neutrons. This work was partially supported by the GACR grant No. P205/12/0454 and by the RFBR research project No. 13-08-00479-a.

Interchange Reconnection Associated with a Confined Filament Eruption: Implications for the Source of Transient Cold-dense Plasma in Solar Winds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Ruisheng; Chen, Yao; Wang, Bing

The cold-dense plasma is occasionally detected in the solar wind with in situ data, but the source of the cold-dense plasma remains illusive. Interchange reconnections (IRs) between closed fields and nearby open fields are known to contribute to the formation of solar winds. We present a confined filament eruption associated with a puff-like coronal mass ejection (CME) on 2014 December 24. The filament underwent successive activations and finally erupted, due to continuous magnetic flux cancelations and emergences. The confined erupting filament showed a clear untwist motion, and most of the filament material fell back. During the eruption, some tiny blobsmore » escaped from the confined filament body, along newly formed open field lines rooted around the south end of the filament, and some bright plasma flowed from the north end of the filament to remote sites at nearby open fields. The newly formed open field lines shifted southward with multiple branches. The puff-like CME also showed multiple bright fronts and a clear southward shift. All the results indicate an intermittent IR existed between closed fields of the confined erupting filament and nearby open fields, which released a portion of filament material (blobs) to form the puff-like CME. We suggest that the IR provides a possible source of cold-dense plasma in the solar wind.« less

No Evidence for Emotional Empathy in Chickens Observing Familiar Adult Conspecifics

PubMed Central

Edgar, Joanne L.; Paul, Elizabeth S.; Harris, Lauren; Penturn, Sarah; Nicol, Christine J.

2012-01-01

The capacity of animals to empathise is of high potential relevance to the welfare of group-housed domestic animals. Emotional empathy is a multifaceted and multilayered phenomenon which ranges from relatively simple processes such as emotional matching behaviour to more complex processes involving interaction between emotional and cognitive perspective taking systems. Our previous research has demonstrated that hens show clear behavioural and physiological responses to the mild distress of their chicks. To investigate whether this capacity exists outside the mother/offspring bond, we conducted a similar experiment in which domestic hens were exposed to the mild distress of unrelated, but familiar adult conspecifics. Each observer hen was exposed to two replicates of four conditions, in counterbalanced order; control (C); control with noise of air puff (CN); air puff to conspecific hen (APC); air puff to observer hen (APH). During each test, the observer hens' behaviour and physiology were measured throughout a 10 min pre-treatment and a 10 min treatment period. Despite showing signs of distress in response to an aversive stimulus directed at themselves (APH), and using methodology sufficiently sensitive to detect empathy-like responses previously, observer hens showed no behavioural or physiological responses to the mild distress of a familiar adult conspecific. The lack of behavioural and physiological response indicates that hens show no basis for emotional empathy in this context. PMID:22348100

Multicolor, time-gated, soft x-ray pinhole imaging of wire array and gas puff Z pinches on the Z and Saturn pulsed power generators.

PubMed

Jones, B; Coverdale, C A; Nielsen, D S; Jones, M C; Deeney, C; Serrano, J D; Nielsen-Weber, L B; Meyer, C J; Apruzese, J P; Clark, R W; Coleman, P L

2008-10-01

A multicolor, time-gated, soft x-ray pinhole imaging instrument is fielded as part of the core diagnostic set on the 25 MA Z machine [M. E. Savage et al., in Proceedings of the Pulsed Power Plasma Sciences Conference (IEEE, New York, 2007), p. 979] for studying intense wire array and gas puff Z-pinch soft x-ray sources. Pinhole images are reflected from a planar multilayer mirror, passing 277 eV photons with <10 eV bandwidth. An adjacent pinhole camera uses filtration alone to view 1-10 keV photons simultaneously. Overlaying these data provides composite images that contain both spectral as well as spatial information, allowing for the study of radiation production in dense Z-pinch plasmas. Cu wire arrays at 20 MA on Z show the implosion of a colder cloud of material onto a hot dense core where K-shell photons are excited. A 528 eV imaging configuration has been developed on the 8 MA Saturn generator [R. B. Spielman et al., and A. I. P. Conf, Proc. 195, 3 (1989)] for imaging a bright Li-like Ar L-shell line. Ar gas puff Z pinches show an intense K-shell emission from a zippering stagnation front with L-shell emission dominating as the plasma cools.

Application of bio-huff-`n`-puff technology at Jilin oil field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiu-Yuan Wang; Yan-Fed Xue; Gang Dai

1995-12-31

An enriched culture 48, capable of adapting to the reservoir conditions and fermenting molasses to produce gas and acid, was used as an inoculum for bio- huff-`n`-puff tests at Fuyu oil area of Jilin oil field. The production well was injected with water containing 4-6% (v/v) molasses and inoculum, and then shut in. After 15-21 days, the well was placed back in operation. A total of 44 wells were treated, of which only two wells showed no effects. The daily oil production of treated wells increased by 33.3-733.3%. Up to the end of 1994, the oil production was increased bymore » 204 tons per well on average. Results obtained from various types of production wells were discussed.« less

Noncontact measurement of elasticity for the detection of soft-tissue tumors using phase-sensitive optical coherence tomography combined with a focused air-puff system.

PubMed

Wang, Shang; Li, Jiasong; Manapuram, Ravi Kiran; Menodiado, Floredes M; Ingram, Davis R; Twa, Michael D; Lazar, Alexander J; Lev, Dina C; Pollock, Raphael E; Larin, Kirill V

2012-12-15

We report on an optical noncontact method for the detection of soft-tissue tumors based on the measurement of their elasticity. A focused air-puff system is used to excite surface waves (SWs) on soft tissues with transient static pressure. A high-speed phase-sensitive optical coherence tomography system is used to measure the SWs as they propagate from the point of excitation. To evaluate the stiffness of soft tissues, the Young's modulus is quantified based on the group velocity of SWs. Pilot experiments were performed on ex vivo human myxoma and normal fat. Results demonstrate the feasibility of the proposed method to measure elasticity and differentiate soft-tissue tumors from normal tissues.

A stand-alone compact EUV microscope based on gas-puff target source.

PubMed

Torrisi, Alfio; Wachulak, Przemyslaw; Węgrzyński, Łukasz; Fok, Tomasz; Bartnik, Andrzej; Parkman, Tomáš; Vondrová, Šárka; Turňová, Jana; Jankiewicz, Bartłomiej J; Bartosewicz, Bartosz; Fiedorowicz, Henryk

2017-02-01

We report on a very compact desk-top transmission extreme ultraviolet (EUV) microscope based on a laser-plasma source with a double stream gas-puff target, capable of acquiring magnified images of objects with a spatial (half-pitch) resolution of sub-50 nm. A multilayer ellipsoidal condenser is used to focus and spectrally narrow the radiation from the plasma, producing a quasi-monochromatic EUV radiation (λ = 13.8 nm) illuminating the object, whereas a Fresnel zone plate objective forms the image. Design details, development, characterization and optimization of the EUV source and the microscope are described and discussed. Test object and other samples were imaged to demonstrate superior resolution compared to visible light microscopy. © 2016 The Authors Journal of Microscopy © 2016 Royal Microscopical Society.

The influence of intraocular pressure and air jet pressure on corneal contactless tonometry tests.

PubMed

Simonini, Irene; Pandolfi, Anna

2016-05-01

The air puff is a dynamic contactless tonometer test used in ophthalmology clinical practice to assess the biomechanical properties of the human cornea and the intraocular pressure due to the filling fluids of the eye. The test is controversial, since the dynamic response of the cornea is governed by the interaction of several factors which cannot be discerned within a single measurement. In this study we describe a numerical model of the air puff tests, and perform a parametric analysis on the major action parameters (jet pressure and intraocular pressure) to assess their relevance on the mechanical response of a patient-specific cornea. The particular cornea considered here has been treated with laser reprofiling to correct myopia, and the parametric study has been conducted on both the preoperative and postoperative geometries. The material properties of the cornea have been obtained by means of an identification procedure that compares the static biomechanical response of preoperative and postoperative corneas under the physiological IOP. The parametric study on the intraocular pressure suggests that the displacement of the cornea׳s apex can be a reliable indicator for tonometry, and the one on the air jet pressure predicts the outcomes of two or more distinct measurements on the same cornea, which can be used in inverse procedures to estimate the material properties of the tissue. Copyright © 2015 Elsevier Ltd. All rights reserved.

Bacteria transport through porous media. Annual report, December 31, 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yen, T.F.

1986-09-01

The following five chapters in this report have been processed separately for inclusion in the Energy Data Base: (1) theoretical model of convective diffusion of motile and non-motile bacteria toward solid surfaces; (2) interfacial electrochemistry of oxide surfaces in oil-bearing sands and sandstones; (3) effects of sodium pyrophosphate additive on the ''huff and puff''/nutrient flooding MEOR process; (4) interaction of Escherichia coli B, B/4, and bacteriophage T4D with Berea sandstone rock in relation to enhanced oil recovery; and (5) transport of bacteria in porous media and its significance in microbial enhanced oil recovery.

Impact analysis of traffic-related air pollution based on real-time traffic and basic meteorological information.

PubMed

Pan, Long; Yao, Enjian; Yang, Yang

2016-12-01

With the rapid development of urbanization and motorization in China, traffic-related air pollution has become a major component of air pollution which constantly jeopardizes public health. This study proposes an integrated framework for estimating the concentration of traffic-related air pollution with real-time traffic and basic meteorological information and also for further evaluating the impact of traffic-related air pollution. First, based on the vehicle emission factor models sensitive to traffic status, traffic emissions are calculated according to the real-time link-based average traffic speed, traffic volume, and vehicular fleet composition. Then, based on differences in meteorological conditions, traffic pollution sources are divided into line sources and point sources, and the corresponding methods to determine the dynamic affecting areas are also proposed. Subsequently, with basic meteorological data, Gaussian dispersion model and puff integration model are applied respectively to estimate the concentration of traffic-related air pollution. Finally, the proposed estimating framework is applied to calculate the distribution of CO concentration in the main area of Beijing, and the population exposure is also calculated to evaluate the impact of traffic-related air pollution on public health. Results show that there is a certain correlation between traffic indicators (i.e., traffic speed and traffic intensity) of the affecting area and traffic-related CO concentration of the target grid, which indicates the methods to determine the affecting areas are reliable. Furthermore, the reliability of the proposed estimating framework is verified by comparing the predicted and the observed ambient CO concentration. In addition, results also show that the traffic-related CO concentration is higher in morning and evening peak hours, and has a heavier impact on public health within the Fourth Ring Road of Beijing due to higher population density and higher CO concentration under calm wind condition in this area. Copyright © 2016 Elsevier Ltd. All rights reserved.

SIRANERISK: Modelling dispersion of steady and unsteady pollutant releases in the urban canopy

NASA Astrophysics Data System (ADS)

Soulhac, L.; Lamaison, G.; Cierco, F.-X.; Ben Salem, N.; Salizzoni, P.; Mejean, P.; Armand, P.; Patryl, L.

2016-09-01

SIRANERISK is an operational model for the simulation of the dispersion of unsteady atmospheric releases of pollutant within and above an urban area. SIRANERISK is built on the same principles as the SIRANE model, and couples a street network model for the pollutant transfers within the urban canopy with a Gaussian puff model for the transfers above it. The performance of the model are here analysed by a detailed comparisons with wind-tunnel experiments. These experiments concern the dispersion of steady and unsteady pollutant releases within and above obstacle arrays with varying geometrical configurations, representing different topologies of idealised urban districts. The overall good agreement between numerical and experimental data demonstrates the reliability of SIRANERISK as an operational tool for the assessment of risk analysis and for the management of crises due to the accidental release of harmful airborne pollutants within a built environment.

Comparison of the relative airways and systemic potencies of inhaled fenoterol and salbutamol in asthmatic patients.

PubMed Central

Lipworth, B. J.; Newnham, D. M.; Clark, R. A.; Dhillon, D. P.; Winter, J. H.; McDevitt, D. G.

1995-01-01

BACKGROUND--There is controversy as to the relative safety of fenoterol and salbutamol. No differences have been found in the relative cardiac beta 1/beta 2 receptor activity of inhaled fenoterol and salbutamol in normal subjects. These initial findings have been extended by comparing the respective potencies of equivalent doses by weight of fenoterol and salbutamol in asthmatic subjects, in terms of airways and systemic responses. METHODS--Eighteen asthmatic patients of mean (SD) age 40 (14) years and a forced expiratory volume in one second (FEV1)% predicted of 56 (14)% (1.97 (0.66)1) were randomised to inhale fenoterol (100 micrograms/puff or 200 micrograms/puff), salbutamol, or placebo (100 micrograms/puff or 200 micrograms/puff) on three separate days. Dose-response curves were constructed using cumulative doses of 100 micrograms, 200 micrograms, 400 micrograms, 1000 micrograms, 2000 micrograms, and 4000 micrograms, and airways and systemic responses were measured 20 minutes after each dose with 40 minute increments. Dose ratios for the relative potency of fenoterol versus salbutamol were calculated from the dose-response curves using regression analysis of parallel slopes. RESULTS--There was no difference in bronchodilator potency between fenoterol and salbutamol (as median dose ratio): FEV1 1.1 (95% CI 0.4 to 4.6). In contrast, dose ratios for systemic responses showed that fenoterol was more potent than salbutamol: serum potassium 3.7 (95% CI 2.0 to 6.0), tremor 5.7 (95% CI 1.4 to 10.2), heart rate 1.6 (95% CI 1.0 to 2.3). At a conventional dose of 200 micrograms the only difference in response between the two drugs was observed for tremor (as mean difference): 0.23 log units (95% CI 0.06 to 0.41 log units). CONCLUSIONS--There was no difference in the bronchodilator potency between fenoterol and salbutamol on a microgram equivalent basis. In contrast, systemic potency was greater with fenoterol, although this difference was not clinically relevant at conventional dosages up to 200 micrograms. PMID:7886650

'Real-world' compensatory behaviour with low nicotine concentration e-liquid: subjective effects and nicotine, acrolein and formaldehyde exposure.

PubMed

Dawkins, Lynne; Cox, Sharon; Goniewicz, Maciej; McRobbie, Hayden; Kimber, Catherine; Doig, Mira; Kośmider, Leon

2018-06-07

To compare the effects of i) high versus low nicotine concentration e-liquid, ii) fixed versus adjustable power and iii) the interaction between the two on: a) vaping behaviour, b) subjective effects, c) nicotine intake, and d) exposure to acrolein and formaldehyde in e-cigarette users vaping in their everyday setting. Counterbalanced, repeated measures with four conditions: i) low nicotine (6 mg/mL)/fixed power; ii) low nicotine/adjustable power; iii) high nicotine (18 mg/mL)/fixed power; iv) high nicotine/adjustable power. London and the South East, England. Twenty experienced e-cigarette users (recruited between September 2016 and February 2017) vaped ad libitum using an eVic Supreme™ with a 'Nautilus Aspire' tank over four weeks (one week per condition). Puffing patterns (daily puff number [PN], puff duration [PD], inter-puff interval [IPI]), mL of e-liquid consumed, changes to power (where permitted), and subjective effects (urge to vape, nicotine withdrawal symptoms) were measured in each condition. Nicotine intake was measured via salivary cotinine. 3-hydroxypropylmercapturic acid (3-HPMA), a metabolite of the toxicant acrolein, and formate, a metabolite of the carcinogen formaldehyde, were measured in urine. There was a significant nicotine concentration x power interaction for PD (p<0.01). PD was longer with low nicotine/fixed power compared with i) high nicotine/fixed power (p< 0.001 and ii) low nicotine/adjustable power (p< 0.01). PN and liquid consumed were higher in the low versus high nicotine condition (main effect of nicotine, p<0.05). Urge to vape and withdrawal symptoms were lower, and nicotine intake was higher, in the high nicotine condition (main effects of nicotine: p<0.01). Whilst acrolein levels did not differ, there was a significant nicotine x power interaction for formaldehyde (p<0.05). Use of a lower nicotine concentration e-liquid may be associated with compensatory behaviour (e.g., higher number and duration of puffs) and increases in negative affect, urge to vape, and formaldehyde exposure. This article is protected by copyright. All rights reserved.

E-cigarette puffing patterns associated with high and low nicotine e-liquid strength: effects on toxicant and carcinogen exposure.

PubMed

Cox, Sharon; Kośmider, Leon; McRobbie, Hayden; Goniewicz, Maciej; Kimber, Catherine; Doig, Mira; Dawkins, Lynne

2016-09-20

Contrary to intuition, use of lower strength nicotine e-liquids might not offer reduced health risk if compensatory puffing behaviour occurs. Compensatory puffing (e.g. more frequent, longer puffs) or user behaviour (increasing the wattage) can lead to higher temperatures at which glycerine and propylene glycol (solvents used in e-liquids) undergo decomposition to carbonyl compounds, including the carcinogens formaldehyde and acetaldehyde. This study aims to document puffing patterns and user behaviour associated with using high and low strength nicotine e-liquid and associated toxicant/carcinogen exposure in experienced e-cigarette users (known as vapers herein). A counterbalanced repeated measures design. Non-tobacco smoking vapers; have used an e-cigarette for ≥3 months; currently using nicotine strength e-liquid ≥12mg/mL and a second or third generation device. This study will measure puffing patterns in vapers whilst they use high and low strength nicotine e-liquid under fixed and user-defined settings, each for a week. The 4 counterbalanced conditions are: i) low strength (6mg/mL), fixed settings; ii) low strength user-defined settings; iii) high strength (18mg/mL) fixed settings; iv) high strength user-defined settings. Biomarkers of exposure to toxicants and carcinogens will be measured in urine. In the second phase of this study, toxicant yields will be measured in aerosol generated using a smoking machine operated to replicate the puffing behaviours of each participant. i) Puffing patterns (mean puff number, puff duration, inter-puff interval and mL of liquid consumed) and user behaviour (changes to device settings: voltage and air-flow) associated with using high and low strength nicotine e-liquid. ii) Toxicant/carcinogen exposure associated with the puffing patterns/device settings used by our participants. i) Subjective effects. ii) comparisons with toxicant exposure from tobacco smoke (using documented evidence) and with recommended safety limits. Twenty participants. The findings will have important implications for public health messaging regarding the relative risks and subjective effects associated with using high and low strength nicotine e-liquid, and for policy makers regarding regulations on nicotine concentrations in e-liquids.

Electronic cigarette nicotine delivery can exceed that of combustible cigarettes: a preliminary report.

PubMed

Ramôa, Carolina P; Hiler, Marzena M; Spindle, Tory R; Lopez, Alexa A; Karaoghlanian, Nareg; Lipato, Thokozeni; Breland, Alison B; Shihadeh, Alan; Eissenberg, Thomas

2016-04-01

Electronic cigarettes (ECIGs) aerosolise a liquid that usually contains propylene glycol and/or vegetable glycerine, flavourants and the dependence-producing drug, nicotine, in various concentrations. This laboratory study examined the relationship between liquid nicotine concentration and plasma nicotine concentration and puffing behaviour in experienced ECIG users. Sixteen ECIG-experienced participants used a 3.3-Volt ECIG battery attached to a 1.5-Ohm dual-coil 'cartomiser' loaded with 1 mL of a flavoured propylene glycol/vegetable glycerine liquid to complete four sessions, at least 2 days apart, that differed by nicotine concentration (0, 8, 18 or 36 mg/mL). In each session, participants completed two 10-puff ECIG-use bouts (30 s puff interval) separated by 60 min. Venous blood was sampled to determine plasma nicotine concentration. Puff duration, volume and average flow rate were measured. Immediately after bout 1, mean plasma nicotine concentration was 5.5 ng/mL (SD=7.7) for 0 mg/mL liquid, with significantly (p<0.05) higher mean concentrations observed for the 8 (mean=17.8 ng/mL, SD=14.6), 18 (mean=25.9 ng/mL, SD=17.5) and 36 mg/mL (mean=30.2 ng/mL; SD=20.0) concentrations; a similar pattern was observed for bout 2. For bout 1, at 36 mg/mL, the mean post- minus pre-bout difference was 24.1 ng/mL (SD=18.3). Puff topography data were consistent with previous results and revealed few reliable differences across conditions. This study demonstrates a relationship between ECIG liquid nicotine concentration and user plasma nicotine concentration in experienced ECIG users. Nicotine delivery from some ECIGs may exceed that of a combustible cigarette. The rationale for this higher level of nicotine delivery is uncertain. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

BREEDING SUPER-EARTHS AND BIRTHING SUPER-PUFFS IN TRANSITIONAL DISKS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Eve J.; Chiang, Eugene, E-mail: evelee@berkeley.edu, E-mail: echiang@astro.berkeley.edu

The riddle posed by super-Earths (1–4R{sub ⊕}, 2–20M{sub ⊕}) is that they are not Jupiters: their core masses are large enough to trigger runaway gas accretion, yet somehow super-Earths accreted atmospheres that weigh only a few percent of their total mass. We show that this puzzle is solved if super-Earths formed late, as the last vestiges of their parent gas disks were about to clear. This scenario would seem to present fine-tuning problems, but we show that there are none. Ambient gas densities can span many (in one case up to 9) orders of magnitude, and super-Earths can still robustlymore » emerge after ∼0.1–1 Myr with percent-by-weight atmospheres. Super-Earth cores are naturally bred in gas-poor environments where gas dynamical friction has weakened sufficiently to allow constituent protocores to gravitationally stir one another and merge. So little gas is present at the time of core assembly that cores hardly migrate by disk torques: formation of super-Earths can be in situ. The basic picture—that close-in super-Earths form in a gas-poor (but not gas-empty) inner disk, fed continuously by gas that bleeds inward from a more massive outer disk—recalls the largely evacuated but still accreting inner cavities of transitional protoplanetary disks. We also address the inverse problem presented by super-puffs: an uncommon class of short-period planets seemingly too voluminous for their small masses (4–10R{sub ⊕}, 2–6M{sub ⊕}). Super-puffs most easily acquire their thick atmospheres as dust-free, rapidly cooling worlds outside ∼1 AU where nebular gas is colder, less dense, and therefore less opaque. Unlike super-Earths, which can form in situ, super-puffs probably migrated in to their current orbits; they are expected to form the outer links of mean-motion resonant chains, and to exhibit greater water content. We close by confronting observations and itemizing remaining questions.« less

Comparative Risks of Aldehyde Constituents in Cigarette Smoke Using Transient Computational Fluid Dynamics/Physiologically Based Pharmacokinetic Models of the Rat and Human Respiratory Tracts

PubMed Central

Corley, Richard A.; Kabilan, Senthil; Kuprat, Andrew P.; Carson, James P.; Jacob, Richard E.; Minard, Kevin R.; Teeguarden, Justin G.; Timchalk, Charles; Pipavath, Sudhakar; Glenny, Robb; Einstein, Daniel R.

2015-01-01

Computational fluid dynamics (CFD) modeling is well suited for addressing species-specific anatomy and physiology in calculating respiratory tissue exposures to inhaled materials. In this study, we overcame prior CFD model limitations to demonstrate the importance of realistic, transient breathing patterns for predicting site-specific tissue dose. Specifically, extended airway CFD models of the rat and human were coupled with airway region-specific physiologically based pharmacokinetic (PBPK) tissue models to describe the kinetics of 3 reactive constituents of cigarette smoke: acrolein, acetaldehyde and formaldehyde. Simulations of aldehyde no-observed-adverse-effect levels for nasal toxicity in the rat were conducted until breath-by-breath tissue concentration profiles reached steady state. Human oral breathing simulations were conducted using representative aldehyde yields from cigarette smoke, measured puff ventilation profiles and numbers of cigarettes smoked per day. As with prior steady-state CFD/PBPK simulations, the anterior respiratory nasal epithelial tissues received the greatest initial uptake rates for each aldehyde in the rat. However, integrated time- and tissue depth-dependent area under the curve (AUC) concentrations were typically greater in the anterior dorsal olfactory epithelium using the more realistic transient breathing profiles. For human simulations, oral and laryngeal tissues received the highest local tissue dose with greater penetration to pulmonary tissues than predicted in the rat. Based upon lifetime average daily dose comparisons of tissue hot-spot AUCs (top 2.5% of surface area-normalized AUCs in each region) and numbers of cigarettes smoked/day, the order of concern for human exposures was acrolein > formaldehyde > acetaldehyde even though acetaldehyde yields were 10-fold greater than formaldehyde and acrolein. PMID:25858911

Smoker Reactivity to Cues: Effects on Craving and on Smoking behavior

PubMed Central

Shiffman, Saul; Dunbar, Michael; Kirchner, Thomas; Li, Xiaoxue; Tindle, Hilary; Anderson, Stewart; Scholl, Sarah

2013-01-01

We assessed craving and smoking in response to smoking-relevant cues. 207 daily smokers viewed images related to one of six cue sets (cigarettes, positive and negative affect, alcohol, smoking prohibitions, and neutral cues) in separate sessions. Compared to neutral cues, cigarette cues significantly increased craving, and positive affect cues significantly decreased craving. When subjects were then allowed to smoke during continuing cue exposure, cues did not affect the likelihood of smoking or the amount smoked (number of cigarettes, number of puffs, puff time, or increased carbon monoxide). However, craving intensity predicted likelihood of smoking, latency to smoke, and amount smoked, with craving increases after cue exposure making significant independent contributions. Some craving effects were curvilinear, suggesting that they are subject to thresholds and might not be observed under some circumstances. PMID:22708884

Use of vacuum arc plasma guns for a metal puff Z-pinch system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rousskikh, A. G.; Zhigalin, A. S.; Oreshkin, V. I.

The performance of a metal puff Z-pinch system has been studied experimentally. In this type of system, the initial cylindrical shell 4 cm in diameter was produced by ten plasma guns. Each gun initiates a vacuum arc operating between magnesium electrodes. The net current of the guns was 80 kA. The arc-produced plasma shell was compressed by using a 450-kA, 450-ns driver, and as a result, a plasma column 0.3 cm in diameter was formed. The electron temperature of the plasma reached 400 eV at an average ion concentration of 1.85 {center_dot} 10{sup 18} cm{sup -3}. The power of themore » Mg K-line radiation emitted by the plasma for 15-30 ns was 300 MW/cm.« less

An Observational Study of Group Waterpipe Use in a Natural Environment

PubMed Central

2014-01-01

Introduction: To date research on tobacco smoking with a waterpipe (hookah, narghile, and shisha) has focused primarily on the individual user in a laboratory setting. Yet, waterpipe tobacco smoking is often a social practice that occurs in cafés, homes, and other natural settings. This observational study examined the behavior of waterpipe tobacco smokers and the social and contextual features of waterpipe use among groups in their natural environment. Methods: Trained observers visited urban waterpipe cafés on multiple occasions during an 8-month period. Observations of 241 individual users in naturally formed groups were made on smoking topography (puff frequency, duration, and interpuff interval [IPI]) and engagement in other activities (e.g., food and drink consumption, other tobacco use, and media viewing). Results: Most users were male in group sizes of 3–4 persons, on average, and each table had 1 waterpipe, on average. The predominant social features during observational periods were conversation and nonalcoholic drinking. Greater puff number was associated with smaller group sizes and more waterpipes per group, while longer IPIs were associated with larger group sizes and fewer waterpipes per group. Additionally, greater puff frequency was observed during media viewing and in the absence of other tobacco use. Conclusions: Overall, the results suggest that waterpipe smoking behavior is affected by group size and by certain social activities. Discussion focuses on how these findings enhance our understanding of factors that may influence exposure to waterpipe tobacco smoke toxicants in naturalistic environments. PMID:23943842

Factors Predicting Smoking in a Laboratory-Based Smoking-Choice Task

PubMed Central

Bold, Krysten W.; Yoon, Haewon; Chapman, Gretchen B.; McCarthy, Danielle E.

2013-01-01

This study aimed to expand the current understanding of smoking maintenance mechanisms by examining how putative relapse risk factors relate to a single behavioral smoking choice using a novel laboratory smoking-choice task. After 12 hours of nicotine deprivation, participants were exposed to smoking cues and given the choice between smoking up to two cigarettes in a 15-minute window or waiting and receiving four cigarettes after a delay of 45 minutes. Greater nicotine dependence, higher impulsivity, and lower distress tolerance were hypothesized to predict earlier and more intensive smoking. Out of 35 participants (n=9 female), 26 chose to smoke with a median time to a first puff of 1.22 minutes (standard deviation=2.62 min, range=0.03–10.62 min). Survival analyses examined latency to first puff, and results indicated that greater pre-task craving and smoking more cigarettes per day were significantly related to smoking sooner in the task. Greater behavioral disinhibition predicted shorter smoking latency in the first two minutes of the task, but not at a delay of more than two minutes. Lower distress tolerance (reporting greater regulation efforts to alleviate distress) was related to more puffs smoked and greater nicotine dependence was related to more time spent smoking in the task. This novel laboratory smoking-choice paradigm may be a useful laboratory analog for the choices smokers make during cessation attempts and may help identify factors that influence smoking lapses. PMID:23421357

Flux-driven turbulence GDB simulations of the IWL Alcator C-Mod L-mode edge compared with experiment

NASA Astrophysics Data System (ADS)

Francisquez, Manaure; Zhu, Ben; Rogers, Barrett

2017-10-01

Prior to predicting confinement regime transitions in tokamaks one may need an accurate description of L-mode profiles and turbulence properties. These features determine the heat-flux width upon which wall integrity depends, a topic of major interest for research aid to ITER. To this end our work uses the GDB model to simulate the Alcator C-Mod edge and contributes support for its use in studying critical edge phenomena in current and future tokamaks. We carried out 3D electromagnetic flux-driven two-fluid turbulence simulations of inner wall limited (IWL) C-Mod shots spanning closed and open flux surfaces. These simulations are compared with gas puff imaging (GPI) and mirror Langmuir probe (MLP) data, examining global features and statistical properties of turbulent dynamics. GDB reproduces important qualitative aspects of the C-Mod edge regarding global density and temperature profiles, within reasonable margins, and though the turbulence statistics of the simulated turbulence follow similar quantitative trends questions remain about the code's difficulty in exactly predicting quantities like the autocorrelation time A proposed breakpoint in the near SOL pressure and the posited separation between drift and ballooning dynamics it represents are examined This work was supported by DOE-SC-0010508. This research used resources of the National Energy Research Scientific Computing Center (NERSC).

Selection of intracellular calcium patterns in a model with clustered Ca2+ release channels

NASA Astrophysics Data System (ADS)

Shuai, J. W.; Jung, P.

2003-03-01

A two-dimensional model is proposed for intracellular Ca2+ waves, which incorporates both the discrete nature of Ca2+ release sites in the endoplasmic reticulum membrane and the stochastic dynamics of the clustered inositol 1,4,5-triphosphate (IP3) receptors. Depending on the Ca2+ diffusion coefficient and concentration of IP3, various spontaneous Ca2+ patterns, such as calcium puffs, local waves, abortive waves, global oscillation, and tide waves, can be observed. We further investigate the speed of the global waves as a function of the IP3 concentration and the Ca2+ diffusion coefficient and under what conditions the spatially averaged Ca2+ response can be described by a simple set of ordinary differential equations.

Tongue-Driven Wheelchair Out-Maneuvers the Competition

MedlinePlus

... Human Services National Institutes of Health Creating Biomedical Technologies to Improve Health En Español | Site Map | Staff ... of daily experience using the sip-and-puff technology, which requires inhaling and exhaling through a straw ...

ELM-free and inter-ELM divertor heat flux broadening induced by edge harmonics oscillation in NSTX

DOE PAGES

Gan, K. F.; Ahn, J. -W.; Gray, T. K.; ...

2017-10-26

A new n =1 dominated edge harmonic oscillation (EHO) has been found in NSTX. The new EHO, rotating toroidally in the counter-current direction and the opposite direction of the neutral beam, was observed during certain inter-ELM and ELM-free periods of H-mode operation. This EHO is associated with a significant broadening of the integral heat flux width (more » $${{\\lambda}_{\\operatorname{int}}}$$ ) by up to 150%, and a decrease in the divertor peak heat flux by >60%. An EHO induced filament was also observed by the gas puff imaging diagnostic. The toroidal rotating filaments could change the edge magnetic topology resulting in toroidal rotating strike point splitting and heat flux broadening. Finally, experimental result of the counter current rotation of strike points splitting is consistent with the counter-current EHO.« less

Development and application of a reactive plume-in-grid model: evaluation over Greater Paris

NASA Astrophysics Data System (ADS)

Korsakissok, I.; Mallet, V.

2010-02-01

Emissions from major point sources are badly represented by classical Eulerian models. An overestimation of the horizontal plume dilution, a bad representation of the vertical diffusion as well as an incorrect estimate of the chemical reaction rates are the main limitations of such models in the vicinity of major point sources. The plume-in-grid method is a multiscale modeling technique that couples a local-scale Gaussian puff model with an Eulerian model in order to better represent these emissions. We present the plume-in-grid model developed in the air quality modeling system Polyphemus, with full gaseous chemistry. The model is evaluated on the metropolitan Île-de-France region, during six months (summer 2001). The subgrid-scale treatment is used for 89 major point sources, a selection based on the emission rates of NOx and SO2. Results with and without the subgrid treatment of point emissions are compared, and their performance by comparison to the observations at measurement stations is assessed. A sensitivity study is also carried out, on several local-scale parameters as well as on the vertical diffusion within the urban area. Primary pollutants are shown to be the most impacted by the plume-in-grid treatment, with a decrease in RMSE by up to about -17% for SO2 and -7% for NO at measurement stations. SO2 is the most impacted pollutant, since the point sources account for an important part of the total SO2 emissions, whereas NOx emissions are mostly due to traffic. The spatial impact of the subgrid treatment is localized in the vicinity of the sources, especially for reactive species (NOx and O3). Reactive species are mostly sensitive to the local-scale parameters, such as the time step between two puff emissions which influences the in-plume chemical reactions, whereas the almost-passive species SO2 is more sensitive to the injection time, which determines the duration of the subgrid-scale treatment. Future developments include an extension to handle aerosol chemistry, and an application to the modeling of line sources in order to use the subgrid treatment with road emissions. The latter is expected to lead to more striking results, due to the importance of traffic emissions for the pollutants of interest.

Computation of probabilistic hazard maps and source parameter estimation for volcanic ash transport and dispersion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madankan, R.; Pouget, S.; Singla, P., E-mail: psingla@buffalo.edu

Volcanic ash advisory centers are charged with forecasting the movement of volcanic ash plumes, for aviation, health and safety preparation. Deterministic mathematical equations model the advection and dispersion of these plumes. However initial plume conditions – height, profile of particle location, volcanic vent parameters – are known only approximately at best, and other features of the governing system such as the windfield are stochastic. These uncertainties make forecasting plume motion difficult. As a result of these uncertainties, ash advisories based on a deterministic approach tend to be conservative, and many times over/under estimate the extent of a plume. This papermore » presents an end-to-end framework for generating a probabilistic approach to ash plume forecasting. This framework uses an ensemble of solutions, guided by Conjugate Unscented Transform (CUT) method for evaluating expectation integrals. This ensemble is used to construct a polynomial chaos expansion that can be sampled cheaply, to provide a probabilistic model forecast. The CUT method is then combined with a minimum variance condition, to provide a full posterior pdf of the uncertain source parameters, based on observed satellite imagery. The April 2010 eruption of the Eyjafjallajökull volcano in Iceland is employed as a test example. The puff advection/dispersion model is used to hindcast the motion of the ash plume through time, concentrating on the period 14–16 April 2010. Variability in the height and particle loading of that eruption is introduced through a volcano column model called bent. Output uncertainty due to the assumed uncertain input parameter probability distributions, and a probabilistic spatial-temporal estimate of ash presence are computed.« less

High speed movies of turbulence in Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

Terry, J.L.; Zweben, S.J.; Bose, B.

2004-10-01

A high speed (250 kHz), 300 frame charge coupled device camera has been used to image turbulence in the Alcator C-Mod Tokamak. The camera system is described and some of its important characteristics are measured, including time response and uniformity over the field-of-view. The diagnostic has been used in two applications. One uses gas-puff imaging to illuminate the turbulence in the edge/scrape-off-layer region, where D{sub 2} gas puffs localize the emission in a plane perpendicular to the magnetic field when viewed by the camera system. The dynamics of the underlying turbulence around and outside the separatrix are detected in thismore » manner. In a second diagnostic application, the light from an injected, ablating, high speed Li pellet is observed radially from the outer midplane, and fast poloidal motion of toroidal striations are seen in the Li{sup +} light well inside the separatrix.« less

Advances in Dust Detection and Removal for Tokamaks

NASA Astrophysics Data System (ADS)

Campos, A.; Skinner, C. H.; Roquemore, A. L.; Leisure, J. O. V.; Wagner, S.

2008-11-01

Dust diagnostics and removal techniques are vital for the safe operation of next step fusion devices such as ITER. An electrostatic dust detector[1] developed in the laboratory is being applied to NSTX. In the tokamak environment, large particles or fibres can fall on the grid potentially causing a permanent short. We report on the development of a gas puff system that uses helium to clear such particles from the detector. Experiments with varying nozzle designs, backing pressures, puff durations, and exit flow orientations have obtained an optimal configuration that effectively removes particles from a 25 cm^2 area. Dust removal from next step tokamaks will be required to meet regulatory dust limits. A tripolar grid of fine interdigitated traces has been designed that generates an electrostatic travelling wave for conveying dust particles to a ``drain.'' First trials have shown particle motion in optical microscope images. [1] C. H. Skinner et al., J. Nucl. Mater., 376 (2008) 29.

Streamwise-Localized Solutions with natural 1-fold symmetry

NASA Astrophysics Data System (ADS)

Altmeyer, Sebastian; Willis, Ashley; Hof, Björn

2014-11-01

It has been proposed in recent years that turbulence is organized around unstable invariant solutions, which provide the building blocks of the chaotic dynamics. In direct numerical simulations of pipe flow we show that when imposing a minimal symmetry constraint (reflection in an axial plane only) the formation of turbulence can indeed be explained by dynamical systems concepts. The hypersurface separating laminar from turbulent motion, the edge of turbulence, is spanned by the stable manifolds of an exact invariant solution, a periodic orbit of a spatially localized structure. The turbulent states themselves (turbulent puffs in this case) are shown to arise in a bifurcation sequence from a related localized solution (the upper branch orbit). The rather complex bifurcation sequence involves secondary Hopf bifurcations, frequency locking and a period doubling cascade until eventually turbulent puffs arise. In addition we report preliminary results of the transition sequence for pipe flow without symmetry constraints.

Interest in marijuana treatment programs among teenage smokers and nonsmokers.

PubMed

Sheer, Amy J; Gorelick, David A; Collins, Charles C; Schroeder, Jennifer R; Heishman, Stephen J; Leff, Michelle K; Moolchan, Eric T

2009-12-01

Little is known about adolescents' interest in marijuana treatment programs. This question was evaluated by telephone interview in a convenience sample of 575 adolescents responding to advertisements for tobacco research studies. Eighty-one percent of respondents endorsed the need for marijuana treatment programs for adolescents. These adolescents were younger and less likely to smoke tobacco, smoke marijuana, or use alcohol than those not endorsing such a need. Among the 192 marijuana smokers, the 58.8% who endorsed the need for marijuana treatment programs took their first puff of marijuana at a younger age than those who did not endorse the need. Those who were willing to participate in a marijuana treatment program were more likely African American and took their first marijuana puff at a younger age than those not interested in treatment. These findings suggest that most adolescent marijuana smokers endorse the need for and are willing to attend marijuana treatment programs.

Automated source term and wind parameter estimation for atmospheric transport and dispersion applications

NASA Astrophysics Data System (ADS)

Bieringer, Paul E.; Rodriguez, Luna M.; Vandenberghe, Francois; Hurst, Jonathan G.; Bieberbach, George; Sykes, Ian; Hannan, John R.; Zaragoza, Jake; Fry, Richard N.

2015-12-01

Accurate simulations of the atmospheric transport and dispersion (AT&D) of hazardous airborne materials rely heavily on the source term parameters necessary to characterize the initial release and meteorological conditions that drive the downwind dispersion. In many cases the source parameters are not known and consequently based on rudimentary assumptions. This is particularly true of accidental releases and the intentional releases associated with terrorist incidents. When available, meteorological observations are often not representative of the conditions at the location of the release and the use of these non-representative meteorological conditions can result in significant errors in the hazard assessments downwind of the sensors, even when the other source parameters are accurately characterized. Here, we describe a computationally efficient methodology to characterize both the release source parameters and the low-level winds (eg. winds near the surface) required to produce a refined downwind hazard. This methodology, known as the Variational Iterative Refinement Source Term Estimation (STE) Algorithm (VIRSA), consists of a combination of modeling systems. These systems include a back-trajectory based source inversion method, a forward Gaussian puff dispersion model, a variational refinement algorithm that uses both a simple forward AT&D model that is a surrogate for the more complex Gaussian puff model and a formal adjoint of this surrogate model. The back-trajectory based method is used to calculate a ;first guess; source estimate based on the available observations of the airborne contaminant plume and atmospheric conditions. The variational refinement algorithm is then used to iteratively refine the first guess STE parameters and meteorological variables. The algorithm has been evaluated across a wide range of scenarios of varying complexity. It has been shown to improve the source parameters for location by several hundred percent (normalized by the distance from source to the closest sampler), and improve mass estimates by several orders of magnitude. Furthermore, it also has the ability to operate in scenarios with inconsistencies between the wind and airborne contaminant sensor observations and adjust the wind to provide a better match between the hazard prediction and the observations.

Blob structure and motion in the edge and SOL of NSTX

DOE PAGES

Zweben, S. J.; Myra, J. R.; Davis, W. M.; ...

2016-01-28

Here, the structure and motion of discrete plasma blobs (a.k.a. filaments) in the edge and scrape-off layer of NSTX is studied for representative Ohmic and H-mode discharges. Individual blobs were tracked in the 2D radial versus poloidal plane using data from the gas puff imaging diagnostic taken at 400 000 frames s -1. A database of blob amplitude, size, ellipticity, tilt, and velocity was obtained for ~45 000 individual blobs. Empirical relationships between various properties are described, e.g. blob speed versus amplitude and blob tilt versus ellipticity. The blob velocities are also compared with analytic models.

Moth-inspired navigation algorithm in a turbulent odor plume from a pulsating source.

PubMed

Liberzon, Alexander; Harrington, Kyra; Daniel, Nimrod; Gurka, Roi; Harari, Ally; Zilman, Gregory

2018-01-01

Some female moths attract male moths by emitting series of pulses of pheromone filaments propagating downwind. The turbulent nature of the wind creates a complex flow environment, and causes the filaments to propagate in the form of patches with varying concentration distributions. Inspired by moth navigation capabilities, we propose a navigation strategy that enables a flier to locate an upwind pulsating odor source in a windy environment using a single threshold-based detection sensor. This optomotor anemotaxis strategy is constructed based on the physical properties of the turbulent flow carrying discrete puffs of odor and does not involve learning, memory, complex decision making or statistical methods. We suggest that in turbulent plumes from a pulsating point source, an instantaneously measurable quantity referred as a "puff crossing time", improves the success rate as compared to the navigation strategies based on temporally regular zigzags due to intermittent contact, or an "internal counter", that do not use this information. Using computer simulations of fliers navigating in turbulent plumes of the pulsating point source for varying flow parameters such as turbulent intensities, plume meandering and wind gusts, we obtained statistics of navigation paths towards the pheromone sources. We quantified the probability of a successful navigation as well as the flight parameters such as the time spent searching and the total flight time, with respect to different turbulent intensities, meandering or gusts. The concepts learned using this model may help to design odor-based navigation of miniature airborne autonomous vehicles.

I did eat my vegetables. Agreement between parent and child food intake diaries.

PubMed

Rangelov, Natalie; Suggs, L Suzanne; Marques-Vidal, Pedro

2016-12-01

To assess the level of agreement between children and their parents when reporting a child's food consumption. Cross-sectional study in which children and parents independently completed 7 d food diaries describing the foods and drinks the child consumed at every meal and snack. The association between child and parent reporting was assessed for nineteen food groups using Kendall's tau-b non-parametric correlations, Spearman's rank correlations, kappa coefficients and Lin's concordance measure of agreement. Results were also stratified by gender of the child and his/her grade at school. Households in Ticino, Switzerland, April-June 2014. Two hundred and ninety-nine children aged 6-12 years and one of their parents participated, with 264 providing complete data (35 % completion rate). Results showed a high level of agreement between child and parent reporting. Spearman correlations ranged from 0·55 (sauces) and 0·57 (fatty meat) to 0·80 (fruit), 0·83 (starchy foods) and 0·84 (pastries). All nineteen Spearman correlations were significant at the 0·001 level. Kendall's tau-b correlations ranged from 0·44 (fat meat) to 0·81 (puff pastry). Kappa values showed low to high levels of agreement, ranging from 0·15 (sweets) to 0·77 (puff pastry). Lin's concordance correlation coefficients ranged from 0·39 (whole grains) to 0·86 (puff pastry). When assessing the eating behaviour of children using a 7 d food diary, children's reports might be as reliable as their parents'.

Characterization and performance of a field aligned ion cyclotron range of frequency antenna in Alcator C-Mod

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wukitch, S. J.; Garrett, M. L.; Ochoukov, R.

Ion cyclotron range of frequency (ICRF) heating is expected to provide auxiliary heating for ITER and future fusion reactors where high Z metallic plasma facing components (PFCs) are being considered. Impurity contamination linked to ICRF antenna operation remains a major challenge particularly for devices with high Z metallic PFCs. Here, we report on an experimental investigation to test whether a field aligned (FA) antenna can reduce impurity contamination and impurity sources. We compare the modification of the scrape of layer (SOL) plasma potential of the FA antenna to a conventional, toroidally aligned (TA) antenna, in order to explore the underlyingmore » physics governing impurity contamination linked to ICRF heating. The FA antenna is a 4-strap ICRF antenna where the current straps and antenna enclosure sides are perpendicular to the total magnetic field while the Faraday screen rods are parallel to the total magnetic field. In principle, alignment with respect to the total magnetic field minimizes integrated E|| (electric field along a magnetic field line) via symmetry. A finite element method RF antenna model coupled to a cold plasma model verifies that the integrated E|| should be reduced for all antenna phases. Monopole phasing in particular is expected to have the lowest integrated E||. Consistent with expectations, we observed that the impurity contamination and impurity source at the FA antenna are reduced compared to the TA antenna. In both L and H-mode discharges, the radiated power is 20%–30% lower for a FA-antenna heated discharge than a discharge heated with the TA-antennas. However, inconsistent with expectations, we observe RF induced plasma potentials (via gas-puff imaging and emissive probes to be nearly identical for FA and TA antennas when operated in dipole phasing). Moreover, the highest levels of RF-induced plasma potentials are observed using monopole phasing with the FA antenna. Thus, while impurity contamination and sources are indeed reduced with the FA antenna configuration, the mechanism determining the SOL plasma potential in the presence of ICRF and its impact on impurity contamination and sources remains to be understood.« less

A non-LTE kinetic model for quick analysis of K-shell spectra from Z-pinch plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, J., E-mail: s.duan@163.com; Huang, X. B., E-mail: s.duan@163.com; Cai, H. C., E-mail: s.duan@163.com

Analyzing and modeling K-shell spectra emitted by low-to moderate-atomic number plasma is a useful and effective way to retrieve temperature density of z-pinch plasmas. In this paper, a non-LTE population kinetic model for quick analysis of K-shell spectra was proposed. The model contains ionization stages from bare nucleus to neutral atoms and includes all the important atomic processes. In the present form of the model, the plasma is assumed to be both optically thin and homogeneous with constant temperature and density, and only steady-state situation is considered. According to the detailed calculations for aluminum plasmas, contours of ratios of certainmore » K-shell lines in electron temperature and density plane as well as typical synthesized spectra were presented and discussed. The usefulness of the model is demonstrated by analyzing the spectrum from a neon gas-puff Z-pinch experiment performed on a 1 MA pulsed-power accelerator.« less

Evaluation of electronic cigarette use (vaping) topography and estimation of liquid consumption: implications for research protocol standards definition and for public health authorities' regulation.

PubMed

Farsalinos, Konstantinos E; Romagna, Giorgio; Tsiapras, Dimitris; Kyrzopoulos, Stamatis; Voudris, Vassilis

2013-06-18

Although millions of people are using electronic cigarettes (ECs) and research on this topic has intensified in recent years, the pattern of EC use has not been systematically studied. Additionally, no comparative measure of exposure and nicotine delivery between EC and tobacco cigarette or nicotine replacement therapy (NRTs) has been established. This is important, especially in the context of the proposal for a new Tobacco Product Directive issued by the European Commission. A second generation EC device, consisting of a higher capacity battery and tank atomiser design compared to smaller cigarette-like batteries and cartomizers, and a 9 mg/mL nicotine-concentration liquid were used in this study. Eighty subjects were recruited; 45 experienced EC users and 35 smokers. EC users were video-recorded when using the device (ECIG group), while smokers were recorded when smoking (SM-S group) and when using the EC (SM-E group) in a randomized cross-over design. Puff, inhalation and exhalation duration were measured. Additionally, the amount of EC liquid consumed by experienced EC users was measured at 5 min (similar to the time needed to smoke one tobacco cigarette) and at 20 min (similar to the time needed for a nicotine inhaler to deliver 4 mg nicotine). Puff duration was significantly higher in ECIG (4.2 ± 0.7 s) compared to SM-S (2.1 ± 0.4 s) and SM-E (2.3 ± 0.5 s), while inhalation time was lower (1.3 ± 0.4, 2.1 ± 0.4 and 2.1 ± 0.4 respectively). No difference was observed in exhalation duration. EC users took 13 puffs and consumed 62 ± 16 mg liquid in 5 min; they took 43 puffs and consumed 219 ± 56 mg liquid in 20 min. Nicotine delivery was estimated at 0.46 ± 0.12 mg after 5 min and 1.63 ± 0.41 mg after 20 min of use. Therefore, 20.8 mg/mL and 23.8 mg/mL nicotine-containing liquids would deliver 1 mg of nicotine in 5 min and 4 mg nicotine in 20 min, respectively. Since the ISO method significantly underestimates nicotine delivery by tobacco cigarettes, it seems that liquids with even higher than 24 mg/mL nicotine concentration would be comparable to one tobacco cigarette. EC use topography is significantly different compared to smoking. Four-second puffs with 20-30 s interpuff interval should be used when assessing EC effects in laboratory experiments, provided that the equipment used does not get overheated. Based on the characteristics of the device used in this study, a 20 mg/mL nicotine concentration liquid would be needed in order to deliver nicotine at amounts similar to the maximum allowable content of one tobacco cigarette (as measured by the ISO 3308 method). The results of this study do not support the statement of the European Commission Tobacco Product Directive that liquids with nicotine concentration of 4 mg/mL are comparable to NRTs in the amount of nicotine delivered to the user.

Sumo Puff: Tidal debris or disturbed ultra-diffuse galaxy?

NASA Astrophysics Data System (ADS)

Greco, Johnny P.; Greene, Jenny E.; Price-Whelan, Adrian M.; Leauthaud, Alexie; Huang, Song; Goulding, Andy D.; Strauss, Michael A.; Komiyama, Yutaka; Lupton, Robert H.; Miyazaki, Satoshi; Takada, Masahiro; Tanaka, Masayuki; Usuda, Tomonori

2018-01-01

We report the discovery of a diffuse stellar cloud with an angular extent ≳30″, which we term "Sumo Puff", in data from the Hyper Suprime-Cam Subaru Strategic Program (HSC-SSP). While we do not have a redshift for this object, it is in close angular proximity to a post-merger galaxy at redshift z = 0.0431 and is projected within a few virial radii (assuming similar redshifts) of two other ˜L⋆ galaxies, which we use to bracket a potential redshift range of 0.0055 < z < 0.0431. The object's light distribution is flat, as characterized by a low Sérsic index (n ˜ 0.3). It has a low central g-band surface brightness of ˜26.4 mag arcsec-2, large effective radius of ˜13″ (˜11 kpc at z = 0.0431 and ˜1.5 kpc at z = 0.0055), and an elongated morphology (b/a ˜ 0.4). Its red color (g - i ˜ 1) is consistent with a passively evolving stellar population and similar to the nearby post-merger galaxy, and we may see tidal material connecting Sumo Puff with this galaxy. We offer two possible interpretations for the nature of this object: (1) it is an extreme, galaxy-sized tidal feature associated with a recent merger event, or (2) it is a foreground dwarf galaxy with properties consistent with a quenched, disturbed, ultra-diffuse galaxy. We present a qualitative comparison with simulations that demonstrates the feasibility of forming a structure similar to this object in a merger event. Follow-up spectroscopy and/or deeper imaging to confirm the presence of the bridge of tidal material will be necessary to reveal the true nature of this object.

Differential effects of a body image exposure session on smoking urge between physically active and sedentary female smokers.

PubMed

Nair, Uma S; Collins, Bradley N; Napolitano, Melissa A

2013-03-01

Smoking is often used as a maladaptive weight control strategy among female smokers. Many of the perceived benefits accrued from smoking, including enhanced mood, reduced anxiety, and weight control, can also be achieved through physical activity. The purpose of this study was to examine the effects of a novel behavioral task (body-image exposure) that was designed to elicit body image and weight concerns on urge to smoke among 18-24 year old female smokers who vary in levels of physical activity. Using a cue-reactivity paradigm, 16 sedentary (SE) and 21 physically active (PA) female smokers (≥5 cigarettes/day for past 6 months) were exposed to a pilot tested body-image exposure session. Self-reported urge and latency to first puff were obtained before and after exposure session. Paired sample t tests showed significant increases in self-reported urge (p < .01) and quicker latency to first puff (p < .01) at posttest for the entire sample compared with pretest. Results of partial correlation (controlling for body mass index [BMI], nicotine dependence, withdrawal, and depressive symptoms) showed that increased time engaging in vigorous intensity physical activity was associated with lower self-reported urge to smoke at post (r = -0.44; p = .01) but not with latency to first puff (r = -.10; p = .62). These results suggest that among weight-concerned female smokers, physical activity may attenuate smoking urges in a context where weight concerns are increased. Future research should continue to explore effects of physical activity on reactivity to body image and smoking cues and variability in smoking cue-reactivity related to physical activity. (PsycINFO Database Record (c) 2013 APA, all rights reserved).

Tar, CO and delta 9THC delivery from the 1st and 2nd halves of a marijuana cigarette.

PubMed

Tashkin, D P; Gliederer, F; Rose, J; Chang, P; Hui, K K; Yu, J L; Wu, T C

1991-11-01

Previous in vitro studies suggest that, with successive puffs from a marijuana cigarette, delta-9-THC becomes concentrated in the remaining uncombusted portion of the cigarette. These observations are consistent with the common practice of smoking marijuana cigarettes to a smaller butt length than that to which tobacco cigarettes are smoked. The purpose of the present study was to compare the delivery of delta-9-THC, as well as total insoluble smoke particulates (tar) and carbon monoxide, from the distal ("first") versus the proximal ("second") halves of a standard marijuana cigarette during "natural" smoking of marijuana. On 4 separate days, ten habitual marijuana users smoked nearly all or approximately 1/2 of a standard marijuana cigarette (83 mm length; 800-900 mg; 1.24% THC), as follows: day 1, "whole" cigarette (60 mm smoked, leaving a 23-mm butt); day 2, "first" half (first 30 mm); day 3, "second" half (second 30 mm) after the "first" half was presmoked with a syringe; and day 4, "second" half after the "first" half was excised. A previously described smoking apparatus (20) was used for measurement of puff volume and inhaled tar. Puff volume and number were allowed to vary spontaneously (provided that the specified length of cigarette was consumed), while inhaled volume (1.5 liters), breathholding time (14 s) and interpuff interval (30 s) were held constant. Blood samples were withdrawn prior to smoking and serially after completion of smoking for analysis of blood carboxyhemoglobin (COHb) and serum delta-9-THC. Heart rate was measured before and 5 min after smoking. Subjects rated their level of "high" 20 min after completion of smoking.(ABSTRACT TRUNCATED AT 250 WORDS)

The effects of nicotine stimulus and response expectancies on male and female smokers' responses to nicotine-free electronic cigarettes.

PubMed

Copp, Sebastian R; Collins, Jamie L; Dar, Reuven; Barrett, Sean P

2015-01-01

Electronic cigarettes (e-cigarettes) have been reported to reduce tobacco craving and withdrawal; however, the mechanisms underlying these effects have not been elucidated. This study examined the contributions of nicotine stimulus and response expectancies to responses to nicotine-free e-cigarettes in 21 e-cigarette naïve smokers (12 male). Participants completed two randomized experimental sessions in which they administered a nicotine-free e-cigarette. During one session they were informed that the e-cigarette contained nicotine and during the other session they were informed that the e-cigarette was nicotine-free. Participants completed subjective assessments before and immediately after sampling ten puffs from the e-cigarette and were then invited to earn additional puffs using a computerized progressive ratio task. Prior to their enrolment in the study, participants provided an estimate of the relative importance of the nicotine content of e-cigarettes for craving relief. Instructions that the e-cigarette contained nicotine were found to reduce both intention to smoke (p=0.017) and withdrawal-related (p=0.018) craving, regardless of a-priori reported beliefs regarding the relative importance of nicotine. Nicotine content instructions were also found to be associated with a shorter latency to self-administration (p=0.005); however, a Sex×Instructions×Response Expectancy interaction (p=0.008) revealed that this effect was specific to women who had strong a-priori nicotine content craving relief expectations. Neither nicotine content instructions nor response expectancies impacted the number of puffs self-administered. Findings suggest that nicotine content expectations contribute to smokers' responses to e-cigarettes, and that a-priori beliefs about nicotine effects may be especially important in women. Copyright © 2014 Elsevier Ltd. All rights reserved.

Protocol proposal for, and evaluation of, consistency in nicotine delivery from the liquid to the aerosol of electronic cigarettes atomizers: regulatory implications.

PubMed

Farsalinos, Konstantinos E; Yannovits, Nikoletta; Sarri, Theoni; Voudris, Vassilis; Poulas, Konstantinos

2016-06-01

To propose a protocol and evaluate the consistency in nicotine delivery to the aerosol of different types of electronic cigarette (EC) atomizers, as required by regulatory authorities. Three cartomizer and four tank-type atomizer products were tested (three samples per product). The aerosol from three 20-puff sessions from each sample was collected using a smoke machine. Three cartridges from a nicotine inhaler and three tobacco cigarettes were also tested. Analytical laboratory in Greece. Aerosol nicotine levels were measured. Relative standard deviation (RSD, i.e. coefficient of variation) was calculated separately for each cartomizer and replacement atomizer head sample (intrasample RSD) and between different samples (intersample RSD). The percentage difference from the mean, which is used to assess the quality of medicinal nebulizers, was also calculated. The aerosol nicotine levels were 1.01-10.61 mg/20 puffs for ECs, 0.12-0.18 mg/20 puffs for the nicotine inhaler and 1.76-2.20 mg/cigarette for the tobacco cigarettes. The intrasample RSDs were 3.7-12.5% for ECs and 14.3% for the nicotine inhaler and 11.1% for the tobacco cigarettes. The intersample RSDs were higher in cartomizers (range: 6.9-37.8%) compared with tank systems (range: 6.4-9.3%). All tank-type atomizers and one cartomizer were within 75-125% of the mean, as dictated for medicinal nebulizers. Electronic cigarettes that use tank-type atomizers appear to deliver nicotine in more consistent quantities (within the acceptable limits for medicinal nebulizers and similar to the nicotine inhaler) than electronic cigarettes that use cartomizers. The protocol for testing nicotine delivery consistency described in this paper could be used effectively for regulatory purposes. © 2016 Society for the Study of Addiction.

Intense Pulsed Heavy Ion Beam Technology

NASA Astrophysics Data System (ADS)

Masugata, Katsumi; Ito, Hiroaki

Development of intense pulsed heavy ion beam accelerator technology is described for the application of materials processing. Gas puff plasma gun and vacuum arc discharge plasma gun were developed as an active ion source for magnetically insulated pulsed ion diode. Source plasma of nitrogen and aluminum were successfully produced with the gas puff plasma gun and the vacuum arc plasma gun, respectively. The ion diode was successfully operated with gas puff plasma gun at diode voltage 190 kV, diode current 2.2 kA and nitrogen ion beam of ion current density 27 A/cm2 was obtained. The ion composition was evaluated by a Thomson parabola spectrometer and the purity of the nitrogen ion beam was estimated to be 86%. The diode also operated with aluminum ion source of vacuum arc plasma gun. The ion diode was operated at 200 kV, 12 kA, and aluminum ion beam of current density 230 A/cm2 was obtained. The beam consists of aluminum ions (Al(1-3)+) of energy 60-400 keV, and protons (90-130 keV), and the purity was estimated to be 89 %. The development of the bipolar pulse accelerator (BPA) was reported. A double coaxial type bipolar pulse generator was developed as the power supply of the BPA. The generator was tested with dummy load of 7.5 ohm, bipolar pulses of -138 kV, 72 ns (1st pulse) and +130 kV, 70 ns (2nd pulse) were succesively generated. By applying the bipolar pulse to the drift tube of the BPA, nitrogen ion beam of 2 A/cm2 was observed in the cathode, which suggests the bipolar pulse acceleration.

Simulations of Ar gas-puff Z-pinch radiation sources with double shells and central jets on the Z generator

NASA Astrophysics Data System (ADS)

Tangri, V.; Harvey-Thompson, A. J.; Giuliani, J. L.; Thornhill, J. W.; Velikovich, A. L.; Apruzese, J. P.; Ouart, N. D.; Dasgupta, A.; Jones, B.; Jennings, C. A.

2016-10-01

Radiation-magnetohydrodynamic simulations using the non-local thermodynamic equilibrium Mach2-Tabular Collisional-Radiative Equilibrium code in (r, z) geometry are performed for two pairs of recent Ar gas-puff Z-pinch experiments on the refurbished Z generator with an 8 cm diameter nozzle. One pair of shots had an outer-to-inner shell mass ratio of 1:1.6 and a second pair had a ratio of 1:1. In each pair, one of the shots had a central jet. The experimental trends in the Ar K-shell yield and power are reproduced in the calculations. However, the K-shell yield and power are significantly lower than the other three shots for the case of a double-shell puff of 1:1 mass ratio and no central jet configuration. Further simulations of a hypothetical experiment with the same relative density profile of this configuration, but higher total mass, show that the coupled energy from the generator and the K-shell yield can be increased to levels achieved in the other three configurations, but not the K-shell power. Based on various measures of effective plasma radius, the compression in the 1:1 mass ratio and no central jet case is found to be less because the plasma inside the magnetic piston is hotter and of lower density. Because of the reduced density, and the reduced radiation cooling (which is proportional to the square of the density), the core plasma is hotter. Consequently, for the 1:1 outer-to-inner shell mass ratio, the load mass controls the yield and the center jet controls the power.

Nicotine Dependence, “Background” and Cue-Induced Craving and Smoking in the Laboratory

PubMed Central

Dunbar, Michael S.; Shiffman, Saul; Kirchner, Thomas; Tindle, Hilary; Scholl, Sarah

2014-01-01

Background Nicotine dependence has been associated with higher “background” craving and smoking, independent of situational cues. Due in part to conceptual and methodological differences across past studies, the relationship between dependence and cue-reactivity (CR; e.g., cue-induced craving and smoking) remains unclear. Methods 207 daily smokers completed six pictorial CR sessions (smoking, negative affect, positive affect, alcohol, smoking prohibitions, and neutral). Individuals rated craving before (background craving) and after cues, and could smoke following cue exposure. Session videos were coded to assess smoking. Participants completed four nicotine dependence measures. Regression models assessed the relationship of dependence to cue-independent (i.e., pre-cue) and cue-specific (i.e., pre-post cue change for each cue, relative to neutral) craving and smoking (likelihood of smoking, latency to smoke, puff count). Results Dependence was associated with background craving and smoking, but did not predict change in craving across the entire sample for any cue. Among alcohol drinkers, dependence was associated with greater increases in craving following the alcohol cue. Only one dependence measure (Wisconsin Inventory of Smoking Dependence Motives) was consistently associated with smoking reactivity (higher likelihood of smoking, shorter latency to smoke, greater puff count) in response to cues. Conclusion While related to cue-independent background craving and smoking, dependence is not strongly associated with laboratory cue-induced craving under conditions of minimal deprivation. Dependence measures that incorporate situational influences on smoking correlate with greater cue-provoked smoking. This may suggest independent roles for CR and traditional dependence as determinants of smoking, and highlights the importance of assessing behavioral CR outcomes. PMID:25028339

Nicotine dependence, "background" and cue-induced craving and smoking in the laboratory.

PubMed

Dunbar, Michael S; Shiffman, Saul; Kirchner, Thomas R; Tindle, Hilary A; Scholl, Sarah M

2014-09-01

Nicotine dependence has been associated with higher "background" craving and smoking, independent of situational cues. Due in part to conceptual and methodological differences across past studies, the relationship between dependence and cue-reactivity (CR; e.g., cue-induced craving and smoking) remains unclear. 207 daily smokers completed six pictorial CR sessions (smoking, negative affect, positive affect, alcohol, smoking prohibitions, and neutral). Individuals rated craving before (background craving) and after cues, and could smoke following cue exposure. Session videos were coded to assess smoking. Participants completed four nicotine dependence measures. Regression models assessed the relationship of dependence to cue-independent (i.e., pre-cue) and cue-specific (i.e., pre-post cue change for each cue, relative to neutral) craving and smoking (likelihood of smoking, latency to smoke, puff count). Dependence was associated with background craving and smoking, but did not predict change in craving across the entire sample for any cue. Among alcohol drinkers, dependence was associated with greater increases in craving following the alcohol cue. Only one dependence measure (Wisconsin Inventory of Smoking Dependence Motives) was consistently associated with smoking reactivity (higher likelihood of smoking, shorter latency to smoke, greater puff count) in response to cues. While related to cue-independent background craving and smoking, dependence is not strongly associated with laboratory cue-induced craving under conditions of minimal deprivation. Dependence measures that incorporate situational influences on smoking correlate with greater cue-provoked smoking. This may suggest independent roles for CR and traditional dependence as determinants of smoking, and highlights the importance of assessing behavioral CR outcomes. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Nutrition Research.

DTIC Science & Technology

1983-10-01

occurring" sugars 48% Refined and processed sugars 10% Total Fat Saturated fat 10% Poly-unsaturated fat 10% Mono-unsaturated fat 10% 30% Protein 12% 300% i 3...2120 Coffee, Black 2125 Coffee, Decaffeinated 2150 Coleslaw, French or CKD Salad Dressing 2540 Cream Puffs/Eclairs with Custard Filling 2715 Doughnut

Application of Laser Plasma Sources of Soft X-rays and Extreme Ultraviolet (EUV) in Imaging, Processing Materials and Photoionization Studies

NASA Astrophysics Data System (ADS)

Fiedorowicz, H.; Bartnik, A.; Wachulak, P. W.; Jarocki, R.; Kostecki, J.; Szczurek, M.; Ahad, I. U.; Fok, T.; Szczurek, A.; Wȩgrzyński, Ł.

In the paper we present new applications of laser plasma sources of soft X-rays and extreme ultraviolet (EUV) in various areas of plasma physics, nanotechnology and biomedical engineering. The sources are based on a gas puff target irradiated with nanosecond laser pulses from commercial Nd: YAG lasers, generating pulses with time duration from 1 to 10 ns and energies from 0.5 to 10 J at a 10 Hz repetition rate. The targets are produced with the use of a double valve system equipped with a special nozzle to form a double-stream gas puff target which allows for high conversion efficiency of laser energy into soft X-rays and EUV without degradation of the nozzle. The sources are equipped with various optical systems to collect soft X-ray and EUV radiation and form the radiation beam. New applications of these sources in imaging, including EUV tomography and soft X-ray microscopy, processing of materials and photoionization studies are presented.

Effect of technological factors on water activity of extruded corn product with an addition of whey proteins.

PubMed

Makowska, Agnieszka; Cais-Sokolińska, Dorota; Lasik, Agata

2014-01-01

The value of water activity in extruded products constitutes a significant indicator of their quality and stability. The state, in which water is found in extruded products, is an indicator of the conducted extrusion process and the used raw material. The aim of the study was to assess water activity in extruded products made from a mixture of com grits with 12.5 and 15.0% moisture contents and different level of addition of whey proteins. It was shown that the degree of mixture moisture content did not have an effect on the value of aw in produced puffs. The greatest difference was recorded when introducing 3% proteins in comparison to aw of puffs produced solely from corn grits. Δaw = 0.023. The greater the content of whey proteins, the lower the aw value. A 3-month storage at a temperature of 18 ±0.5°C influenced aw of snacks produced from a mixture with a higher moisture content.

Renovation of the hot press in the Plutonium Experimental Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, J.W.; Nelson, G.H.

1990-03-05

The Plutonium Experimental Facility (PEF) will be used to develop a new fuel pellet fabrication process and to evaluate equipment upgrades. The facility was used from 1978 until 1982 to optimize the parameters for fuel pellet production using a process which was developed at Los Alamos National Laboratory. The PEF was shutdown and essentially abandoned until mid-1987 when the facility renovations were initiated by the Actinide Technology Section (ATS) of SRL. A major portion of the renovation work was related to the restart of the hot press system. This report describes the renovations and modifications which were required to restartmore » the PEF hot press. The primary purpose of documenting this work is to help provide a basis for Separations to determine the best method of renovating the hot press in the Plutonium Fuel Fabrication (PuFF) facility. This report also includes several SRL recommendations concerning the renovation and modification of the PuFF hot press. 4 refs.« less

Neutron production in deuterium gas-puff z-pinch with outer plasma shell at current of 3 MA

NASA Astrophysics Data System (ADS)

Cikhardt, J.; Klir, D.; Rezac, K.; Cikhardtova, B.; Kravarik, J.; Kubes, P.; Sila, O.; Shishlov, A. V.; Cherdizov, R. K.; Frusov, F. I.; Kokshenev, V. A.; Kurmaev, N. E.; Labetsky, A. Yu.; Ratakhin, N. A.; Dudkin, G. N.; Garapatsky, A. A.; Padalko, V. N.; Varlachev, V. A.; Turek, K.; Krasa, J.

2015-11-01

Z-pinch experiments at the current of about 3 MA were carried out on the GIT-12 generator. The outer plasma shell of deuterium gas-puff was generated by the system of 48 plasma guns. This configuration exhibits a high efficiency of the production of DD fusion neutrons with the yield of above 1012 neutrons produced in a single shot with the duration of about 20 ns. The maximum energy of the neutrons produced in this pulse exceeded 30 MeV. The neutron radiation was measured using scintillation TOF detectors, CR-39 nuclear track detectors, bubble detectors BD-PND and BDS-10000 and by several types of nuclear activation detectors. These diagnostic tools were used to measure the anisotropy of neutron fluence and neutron energy spectra. It allows us to estimate the total number of DD neutrons, the contribution of other nuclear reactions, the amount of scattered neutrons, and other parameters of neutron production. This work was supported by the MSMT grants LH13283, LD14089.

A fast rise-rate, adjustable-mass-bit gas puff valve for energetic pulsed plasma experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loebner, Keith T. K., E-mail: kloebner@stanford.edu; Underwood, Thomas C.; Cappelli, Mark A.

2015-06-15

A fast rise-rate, variable mass-bit gas puff valve based on the diamagnetic repulsion principle was designed, built, and experimentally characterized. The ability to hold the pressure rise-rate nearly constant while varying the total overall mass bit was achieved via a movable mechanical restrictor that is accessible while the valve is assembled and pressurized. The rise-rates and mass-bits were measured via piezoelectric pressure transducers for plenum pressures between 10 and 40 psig and restrictor positions of 0.02-1.33 cm from the bottom of the linear restrictor travel. The mass-bits were found to vary linearly with the restrictor position at a given plenummore » pressure, while rise-rates varied linearly with plenum pressure but exhibited low variation over the range of possible restrictor positions. The ability to change the operating regime of a pulsed coaxial plasma deflagration accelerator by means of altering the valve parameters is demonstrated.« less

Evaluation of Surface Modification as a Lunar Dust Mitigation Strategy for Thermal Control Surfaces

NASA Technical Reports Server (NTRS)

Gaier, James R.; Waters, Deborah L.; Misconin, Robert M.; Banks, Bruce A.; Crowder, Mark

2011-01-01

Three surface treatments were evaluated for their ability to lower the adhesion between lunar simulant dust and AZ93, AlFEP, and AgFEP thermal control surfaces under simulated lunar conditions. Samples were dusted in situ and exposed to a standardized puff of nitrogen gas. Thermal performance before dusting, after dusting, and after part of the dust was removed by the puff of gas, were compared to perform the assessment. None of the surface treatments was found to significantly affect the adhesion of lunar simulants to AZ93 thermal control paint. Oxygen ion beam texturing also did not lower the adhesion of lunar simulant dust to AlFEP or AgFEP. But a workfunction matching coating and a proprietary Ball Aerospace surface treatment were both found to significantly lower the adhesion of lunar simulants to AlFEP and AgFEP. Based on these results, it is recommended that all these two techniques be further explored as dust mitigation coatings for AlFEP and AgFEP thermal control surfaces.

Emissions from Electronic Cigarettes: Assessing Vapers' Intake of Toxic Compounds, Secondhand Exposures, and the Associated Health Impacts.

PubMed

Logue, Jennifer M; Sleiman, Mohamad; Montesinos, V Nahuel; Russell, Marion L; Litter, Marta I; Benowitz, Neal L; Gundel, Lara A; Destaillats, Hugo

2017-08-15

E-cigarettes likely represent a lower risk to health than traditional combustion cigarettes, but they are not innocuous. Recently reported emission rates of potentially harmful compounds were used to assess intake and predict health impacts for vapers and bystanders exposed passively. Vapers' toxicant intake was calculated for scenarios in which different e-liquids were used with various vaporizers, battery power settings and vaping regimes. For a high rate of 250 puff day -1 using a typical vaping regime and popular tank devices with battery voltages from 3.8 to 4.8 V, users were predicted to inhale formaldehyde (up to 49 mg day -1 ), acrolein (up to 10 mg day -1 ) and diacetyl (up to 0.5 mg day -1 ), at levels that exceeded U.S. occupational limits. Formaldehyde intake from 100 daily puffs was higher than the amount inhaled by a smoker consuming 10 conventional cigarettes per day. Secondhand exposures were predicted for two typical indoor scenarios: a home and a bar. Contributions from vaping to air pollutant concentrations in the home did not exceed the California OEHHA 8-h reference exposure levels (RELs), except when a high emitting device was used at 4.8 V. In that extreme scenario, the contributions from vaping amounted to as much as 12 μg m -3 formaldehyde and 2.6 μg m -3 acrolein. Pollutant concentrations in bars were modeled using indoor volumes, air exchange rates and the number of hourly users reported in the literature for U.S. bars in which smoking was allowed. Predicted contributions to indoor air levels were higher than those in the residential scenario. Formaldehyde (on average 135 μg m -3 ) and acrolein (28 μg m -3 ) exceeded the acute 1-h exposure REL for the highest emitting vaporizer/voltage combination. Predictions for these compounds also exceeded the 8-h REL in several bars when less intense vaping conditions were considered. Benzene concentrations in a few bars approached the 8-h REL, and diacetyl levels were close to the lower limit for occupational exposures. The integrated health damage from passive vaping was derived by computing disability-adjusted life years (DALYs) lost due to exposure to secondhand vapor. Acrolein was the dominant contributor to the aggregate harm. DALYs for the various device/voltage combinations were lower than-or comparable to-those estimated for exposures to secondhand and thirdhand tobacco smoke.

Enhanced air dispersion modelling at a typical Chinese nuclear power plant site: Coupling RIMPUFF with two advanced diagnostic wind models.

PubMed

Liu, Yun; Li, Hong; Sun, Sida; Fang, Sheng

2017-09-01

An enhanced air dispersion modelling scheme is proposed to cope with the building layout and complex terrain of a typical Chinese nuclear power plant (NPP) site. In this modelling, the California Meteorological Model (CALMET) and the Stationary Wind Fit and Turbulence (SWIFT) are coupled with the Risø Mesoscale PUFF model (RIMPUFF) for refined wind field calculation. The near-field diffusion coefficient correction scheme of the Atmospheric Relative Concentrations in the Building Wakes Computer Code (ARCON96) is adopted to characterize dispersion in building arrays. The proposed method is evaluated by a wind tunnel experiment that replicates the typical Chinese NPP site. For both wind speed/direction and air concentration, the enhanced modelling predictions agree well with the observations. The fraction of the predictions within a factor of 2 and 5 of observations exceeds 55% and 82% respectively in the building area and the complex terrain area. This demonstrates the feasibility of the new enhanced modelling for typical Chinese NPP sites. Copyright © 2017 Elsevier Ltd. All rights reserved.

Advanced Kr Atomic Structure and Ionization Kinetics for Pinches on ZR

NASA Astrophysics Data System (ADS)

Dasgupta, Arati; Clark, Robert; Giuliani, John; Ouart, Nick; Davis, Jack; Jones, Brent; Ampleford, Dave; Hansen, Stephanie

2011-10-01

High fluence photon sources above 10 keV are a challenge for HED plasmas. This motivates Kr atomic modeling as its K-shell radiation starts at 13 keV. We have developed atomic structure and collisional-radiatve data for the full K-and L-shell and much of the M-shell using the the state-of-the-art Flexible Atomic Code. All relevant atomic collisional and radiative processes that affect ionization balance and are necessary to accurately model the pinch dynamics and the spectroscopic details of the emitted radiation are included in constructing the model. This non-LTE CRE model will be used to generate synthetic spectra for fixed densities and temperatures relevant for Kr gas-puff simulations in ZR. Work supported by DOE/NNSA. Sandia is a multi-program laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Analysis and modeling of localized invariant solutions in pipe flow

NASA Astrophysics Data System (ADS)

Ritter, Paul; Zammert, Stefan; Song, Baofang; Eckhardt, Bruno; Avila, Marc

2018-01-01

Turbulent spots surrounded by laminar flow are a landmark of transitional shear flows, but the dependence of their kinematic properties on spatial structure is poorly understood. We here investigate this dependence in pipe flow for Reynolds numbers between 1500 and 5000. We compute spatially localized relative periodic orbits in long pipes and show that their upstream and downstream fronts decay exponentially towards the laminar profile. This allows us to model the fronts by employing the linearized Navier-Stokes equations, and the resulting model yields the spatial decay rate and the front velocity profiles of the periodic orbits as a function of Reynolds number, azimuthal wave number, and propagation speed. In addition, when applied to a localized turbulent puff, the model is shown to accurately approximate the spatial decay rate of its upstream and downstream tails. Our study provides insight into the relationship between the kinematics and spatial structure of localized turbulence and more generally into the physics of localization.

Modeling of blob-hole correlations in GPI edge turbulence data

NASA Astrophysics Data System (ADS)

Myra, J. R.; Russell, D. A.; Zweben, S. J.

2017-10-01

Gas-puff imaging (GPI) observations made on NSTX have revealed two-point spatial correlation patterns in the plane perpendicular to the magnetic field. A common feature is the occurrence of dipole-like patterns with significant regions of negative correlation. In this work, we explore the possibility that these dipole patterns may be due to blob-hole pairs. Statistical methods are applied to determine the two-point spatial correlation that results from a model of blob-hole pair formation. It is shown that the model produces dipole correlation patterns that are qualitatively similar to the GPI data in many respects. Effects of the reference location (confined surfaces or scrape-off layer), a superimposed random background, hole velocity and lifetime, and background sheared flows are explored. The possibility of using the model to ascertain new information about edge turbulence is discussed. Work supported by the U.S. Department of Energy Office of Science, Office of Fusion Energy Sciences under Award Number DE-FG02-02ER54678.

Muscarinic agonists and ATP increase the intracellular Ca2+ concentration in chick cochlear hair cells.

PubMed

Shigemoto, T; Ohmori, H

1990-01-01

1. Cholinergic muscarinic agonists applied by the pressure puff method increased intracellular Ca2+ concentration in Fura-2-loaded hair cells. The Ca2+ response outlasted the agonist application. 2. The Ca2+ response induced by acetylcholine (ACh) was ACh dose dependent with a KD of 200 microM. Desensitization was negligible, and almost identical Ca2+ responses were observed when two ACh puffs were separated by 150 s. The response was blocked by d-tubocurarine (dTC). The KD of dTC blocking was 500 microM when 100 microM-ACh induced the Ca2+ response. 3. The amplitude of the ACh-induced Ca2+ responses were potentiated to 3 times the control by incubation with calcitonin gene-related peptide (CGRP; 0.1-1 microM). CGRP did not affect the resting Ca2+ concentration. Glycine (100 microM) potentiated the ACh response to 1.4 times the control, and also increased the resting Ca2+ concentration slightly. 4. The ACh-induced Ca2+ response was suppressed by atropine. It was induced in Ca2(+)-free extracellular medium, and in Ca2(+)-free medium desensitization to a second ACh stimulation was significant. The amplitude of the second Ca2+ response was 44% of the first when two ACh puffs were separated by 117 s in Ca2+ free medium. 5. Muscarine and carbamylcholine induced similar Ca2+ responses, with KD values of 130 microM for muscarine and 340 microM for carbamylcholine. Desensitization of Ca2+ responses was negligible in both agonists. 6. ATP co-exists with ACh in some presynaptic nerve terminals (Burnstock, 1981). Puff-applied ATP (100 microM) generated a Ca2+ response with a rapid rising phase and a following slow phase. In Ca2(+)-free medium the rapid phase disappeared and only the slow phase was observed. The rapid phase is due to the influx of Ca2+ ions and the slow phase is due to a release of Ca2+ ions from an intracellular reservoir. Under voltage clamp ATP induced a fast inward current and a following slow outward current. 7. Nicotine, adenosine, glycine, GABA, glutamate and bradykinin did not induce Ca2+ responses in the hair cell. 8. ACh induced hyperpolarization of the hair cell membrane under current clamp, most probably by the activation of Ca2+ activated K+ conductance. Therefore, a cholinergic muscarinic receptor may mediate the inhibitory effects of efferent innervation observed in hair cells.

Inhaled beclomethasone dipropionate improves acoustic measures of voice in patients with asthma.

PubMed

Balter, M S; Adams, S G; Chapman, K R

2001-12-01

Inhaled corticosteroids have the potential to produce upper-airway side effects such as hoarseness. As new compounds and delivery devices are developed and compared, it is difficult to quantify their adverse upper-airway effects. We undertook the following study to test the ability of an acoustic analysis technique to quantify changes in vocal function in steroid-naive patients with asthma who receive inhaled beclomethasone dipropionate (BDP), 1,000 microg/d for 4 months. Patients self-administered one of four regimens of inhaled BDP. Group 1 patients received one 250-microg puff qid via metered-dose inhaler (MDI); group 2 patients received one 250-microg puff qid via MDI with a holding chamber; group 3 patients received two 250-microg puffs bid via MDI; and group 4 patients received two 250-microg puffs bid via MDI with a holding chamber. A smaller cohort of nonsmoking asthmatic patients was managed without steroid intervention for 4 months. At baseline and again at 8 weeks and 16 weeks after the initiation of BDP treatment, patients underwent spirometry and methacholine challenge. At baseline and again at 2, 4, 8, 12, and 16 weeks, patients underwent voice recording for analysis of voice parameters. The recorded vowels were low-pass filtered (10 KHz), digitized (22 KHz), and analyzed by software to obtain two acoustic measures: (1) jitter, the cycle-to-cycle variation in the time period of the voice signal; and (2) shimmer, the cycle-to-cycle variation in voice signal amplitude. We recruited 77 patients for randomization to inhaled steroid therapy and 10 patients who continued to receive only occasional inhaled bronchodilator therapy. In all active treatment groups, FEV(1), FVC, and provocative concentration of methacholine causing a 20% fall in FEV(1) improved significantly after BDP treatment. Mean jitter scores, a measurement of variation in voice pitch, were not significantly influenced by BDP treatment. However, mean shimmer scores, a reflection of perturbation in vocal amplitude, fell significantly (p < 0.05) in the active treatment groups. These reductions in shimmer scores were not significantly different in the active treatment groups. Shimmer scores in the bronchodilator-treated group were unchanged during the 16 weeks of follow-up. Our data show that a simple and noninvasive acoustic analysis of voice is sensitive to subclinical changes associated with inhaled corticosteroid therapy. We have shown that 1,000 microg/d of inhaled BDP actually improves specific acoustic measures of voice in patients with inadequately controlled asthma. These improvements were uninfluenced by dosing schedule and whether a spacing chamber was used.

Mean shear flow in recirculating turbulent urban convection and the plume-puff eddy structure below stably stratified inversion layers

NASA Astrophysics Data System (ADS)

Fan, Yifan; Hunt, Julian; Yin, Shi; Li, Yuguo

2018-03-01

The mean and random components of the velocity field at very low wind speeds in a convective boundary layer (CBL) over a wide urban area are dominated by large eddy structures—either turbulent plumes or puffs. In the mixed layer at either side of the edges of urban areas, local mean recirculating flows are generated by sharp horizontal temperature gradients. These recirculation regions also control the mean shear profile and the bent-over plumes across the mixed layer, extending from the edge to the center of the urban area. A simplified physical model was proposed to calculate the mean flow speed at the edges of urban areas. Water tank experiments were carried out to study the mean recirculating flow and turbulent plume structures. The mean speed at urban edges was measured by the particle image velocimetry (PIV), and the plume structures were visualized by the thermalchromic liquid crystal (TLC) sheets. The horizontal velocity calculated by the physical model at the urban edge agrees well with that measured in the water tank experiments, with a root mean square of 0.03. The experiments also show that the pattern of the mean flow over the urban area changes significantly if the shape of the heated area changes or if the form of the heated urban area becomes sub-divided, for example by the creation of nearby but separated "satellite cities." The convective flow over the square urban area is characterized as the diagonal inflow at the lower level and the side outflow at the upper level. The outflow of the small city can be drawn into the inflow region of the large city in the "satellite city" case. A conceptual analysis shows how these changes significantly affect the patterns of dispersion of pollutants in different types of urban areas.

Measuring the glycemic index of foods: interlaboratory study.

PubMed

Wolever, Thomas M S; Brand-Miller, Jennie C; Abernethy, John; Astrup, Arne; Atkinson, Fiona; Axelsen, Mette; Björck, Inger; Brighenti, Furio; Brown, Rachel; Brynes, Audrey; Casiraghi, M Cristina; Cazaubiel, Murielle; Dahlqvist, Linda; Delport, Elizabeth; Denyer, Gareth S; Erba, Daniela; Frost, Gary; Granfeldt, Yvonne; Hampton, Shelagh; Hart, Valerie A; Hätönen, Katja A; Henry, C Jeya; Hertzler, Steve; Hull, Sarah; Jerling, Johann; Johnston, Kelly L; Lightowler, Helen; Mann, Neil; Morgan, Linda; Panlasigui, Leonora N; Pelkman, Christine; Perry, Tracy; Pfeiffer, Andreas F H; Pieters, Marlien; Ramdath, D Dan; Ramsingh, Rayna T; Robert, S Daniel; Robinson, Carol; Sarkkinen, Essi; Scazzina, Francesca; Sison, Dave Clark D; Sloth, Birgitte; Staniforth, Jane; Tapola, Niina; Valsta, Liisa M; Verkooijen, Inge; Weickert, Martin O; Weseler, Antje R; Wilkie, Paul; Zhang, Jian

2008-01-01

Many laboratories offer glycemic index (GI) services. We assessed the performance of the method used to measure GI. The GI of cheese-puffs and fruit-leather (centrally provided) was measured in 28 laboratories (n=311 subjects) by using the FAO/WHO method. The laboratories reported the results of their calculations and sent the raw data for recalculation centrally. Values for the incremental area under the curve (AUC) reported by 54% of the laboratories differed from central calculations. Because of this and other differences in data analysis, 19% of reported food GI values differed by >5 units from those calculated centrally. GI values in individual subjects were unrelated to age, sex, ethnicity, body mass index, or AUC but were negatively related to within-individual variation (P=0.033) expressed as the CV of the AUC for repeated reference food tests (refCV). The between-laboratory GI values (mean+/-SD) for cheese-puffs and fruit-leather were 74.3+/-10.5 and 33.2+/-7.2, respectively. The mean laboratory GI was related to refCV (P=0.003) and the type of restrictions on alcohol consumption before the test (P=0.006, r2=0.509 for model). The within-laboratory SD of GI was related to refCV (P<0.001), the glucose analysis method (P=0.010), whether glucose measures were duplicated (P=0.008), and restrictions on dinner the night before (P=0.013, r2=0.810 for model). The between-laboratory SD of the GI values is approximately 9. Standardized data analysis and low within-subject variation (refCV<30%) are required for accuracy. The results suggest that common misconceptions exist about which factors do and do not need to be controlled to improve precision. Controlled studies and cost-benefit analyses are needed to optimize GI methodology. The trial was registered at clinicaltrials.gov as NCT00260858.

An Exploratory Human Laboratory Experiment Evaluating Vaporized Cannabis in the Treatment of Neuropathic Pain From Spinal Cord Injury and Disease.

PubMed

Wilsey, Barth; Marcotte, Thomas D; Deutsch, Reena; Zhao, Holly; Prasad, Hannah; Phan, Amy

2016-09-01

Using 8-hour human laboratory experiments, we evaluated the analgesic efficacy of vaporized cannabis in patients with neuropathic pain related to injury or disease of the spinal cord, most of whom were experiencing pain despite traditional treatment. After obtaining baseline data, 42 participants underwent a standardized procedure for inhaling 4 puffs of vaporized cannabis containing either placebo, 2.9%, or 6.7% delta 9-THC on 3 separate occasions. A second dosing occurred 3 hours later; participants chose to inhale 4 to 8 puffs. This flexible dosing was used to attempt to reduce the placebo effect. Using an 11-point numerical pain intensity rating scale as the primary outcome, a mixed effects linear regression model showed a significant analgesic response for vaporized cannabis. When subjective and psychoactive side effects (eg, good drug effect, feeling high, etc) were added as covariates to the model, the reduction in pain intensity remained significant above and beyond any effect of these measures (all P < .0004). Psychoactive and subjective effects were dose-dependent. Measurement of neuropsychological performance proved challenging because of various disabilities in the population studied. Because the 2 active doses did not significantly differ from each other in terms of analgesic potency, the lower dose appears to offer the best risk-benefit ratio in patients with neuropathic pain associated with injury or disease of the spinal cord. A crossover, randomized, placebo-controlled human laboratory experiment involving administration of vaporized cannabis was performed in patients with neuropathic pain related to spinal cord injury and disease. This study supports consideration of future research that would include longer duration studies over weeks to months to evaluate the efficacy of medicinal cannabis in patients with central neuropathic pain. Copyright © 2016 American Pain Society. Published by Elsevier Inc. All rights reserved.

Conductive Atomic Force Microscopy | Materials Science | NREL

Science.gov Websites

electrical measurement techniques is the high spatial resolution. For example, C-AFM measurements on : High-resolution image of a sample semiconductor device; the image shows white puff-like clusters on a dark background and was obtained using atomic force microscopy. Bottom: High-resolution image of the

A Classical Conditioning Procedure for the Hearing Assessment of Multiply Handicapped Persons.

ERIC Educational Resources Information Center

Lancioni, Giulio E.; And Others

1989-01-01

Hearing assessments of multiply handicapped children/adolescents were conducted using classical conditioning (with an air puff as unconditioned stimulus) and operant conditioning (with a modified visual reinforcement audiometry procedure or edible reinforcement). Findings indicate that classical conditioning was successful with 21 of the 23…

Calcium Signaling enhancement during oocyte maturation

NASA Astrophysics Data System (ADS)

Jung, Peter; Ullah, Ghanim; Machaca, Khaled

2006-03-01

A Ca2+ signal with a special spatial and temporal characteristic universally removes cell-cycle arrest after fertilization of a mature egg cell. The Ca2+ signal is characterized by a fast rise of intracellular Ca2+ and a slow decay on the time scale of minutes. We use computational modeling of Ca2+ release on the microscale (Ca2+ puffs) and cell-scale in conjunction with experimental knowledge of the changes in the Ca2+ signaling apparatus during oocyte maturation and changing signaling patterns to explore the relationship between organization and sensitivity of IP3 receptors and SERCA pumps and the resulting signaling patterns. We hypothesize that potentiation of the IP3 receptors during oocyte maturation is the main cause for the differentiation in the signaling patterns.

Hooked on the nicotine addiction thesis: a response to DiFranza.

PubMed

Dar, Reuven; Frenk, Hanan

2013-11-18

DiFranza's rebuttal to our critique of the "Hooked on Nicotine" research program misconstrues our arguments beyond recognition. The grossest misrepresentation of our critique by DiFranza is that we devise (by thwarting science) to rescue "the conventional wisdom" of the "threshold model of nicotine addiction." In fact, the difference between our positions lies elsewhere: We believe that nicotine is not an addictive drug and that its contribution to the smoking habit is secondary; DiFranza believes that nicotine is so powerfully addictive that novice smokers can lose autonomy over their smoking behavior after one cigarette or even following a single puff. Our review aimed to critically examine the empirical basis of this extreme version of the nicotine "addiction" model. In this brief commentary we illustrate how the commitment to the nicotine "addiction" theory has biased the methodology and the interpretation of the data in "Hooked on Nicotine" research program.

Optimizing Dense Plasma Focus Neutron Yields with Fast Gas Jets

NASA Astrophysics Data System (ADS)

McMahon, Matthew; Kueny, Christopher; Stein, Elizabeth; Link, Anthony; Schmidt, Andrea

2016-10-01

We report a study using the particle-in-cell code LSP to perform fully kinetic simulations modeling dense plasma focus (DPF) devices with high density gas jets on axis. The high density jet models fast gas puffs which allow for more mass on axis while maintaining the optimal pressure for the DPF. As the density of the jet compared to the background fill increases we find the neutron yield increases, as does the variability in the neutron yield. Introducing perturbations in the jet density allow for consistent seeding of the m =0 instability leading to more consistent ion acceleration and higher neutron yields with less variability. Jets with higher on axis density are found to have the greatest yield. The optimal jet configuration is explored. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Gamma-ray imaging and holdup assays of 235-F PuFF cells 1 & 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aucott, T.

Savannah River National Laboratory (SRNL) Nuclear Measurements (L4120) was tasked with performing enhanced characterization of the holdup in the PuFF shielded cells. Assays were performed in accordance with L16.1-ADS-2460 using two high-resolution gamma-ray detectors. The first detector, an In Situ Object Counting System (ISOCS)-characterized detector, was used in conjunction with the ISOCS Geometry Composer software to quantify grams of holdup. The second detector, a Germanium Gamma-ray Imager (GeGI), was used to visualize the location and relative intensity of the holdup in the cells. Carts and collimators were specially designed to perform optimum assays of the cells. Thick, pencil-beam tungsten collimatorsmore » were fabricated to allow for extremely precise targeting of items of interest inside the cells. Carts were designed with a wide range of motion to position and align the detectors. A total of 24 measurements were made, each typically 24 hours or longer to provide sufficient statistical precision. This report presents the results of the enhanced characterization for cells 1 and 2. The measured gram values agree very well with results from the 2014 study. In addition, images were created using both the 2014 data and the new GeGI data. The GeGI images of the cells walls reveal significant Pu-238 holdup on the surface of the walls in cells 1 and 2. Additionally, holdup is visible in the two pass-throughs from cell 1 to the wing cabinets. This report documents the final element (exterior measurements coupled with gamma-ray imaging and modeling) of the enhanced characterization of cells 1-5 (East Cell Line).« less

Acute electronic cigarette use: nicotine delivery and subjective effects in regular users.

PubMed

Dawkins, Lynne; Corcoran, Olivia

2014-01-01

Electronic cigarettes are becoming increasingly popular among smokers worldwide. Commonly reported reasons for use include the following: to quit smoking, to avoid relapse, to reduce urge to smoke, or as a perceived lower-risk alternative to smoking. Few studies, however, have explored whether electronic cigarettes (e-cigarettes) deliver measurable levels of nicotine to the blood. This study aims to explore in experienced users the effect of using an 18-mg/ml nicotine first-generation e-cigarette on blood nicotine, tobacco withdrawal symptoms, and urge to smoke. Fourteen regular e-cigarette users (three females), who are abstinent from smoking and e-cigarette use for 12 h, each completed a 2.5 h testing session. Blood was sampled, and questionnaires were completed (tobacco-related withdrawal symptoms, urge to smoke, positive and negative subjective effects) at four stages: baseline, 10 puffs, 60 min of ad lib use and a 60-min rest period. Complete sets of blood were obtained from seven participants. Plasma nicotine concentration rose significantly from a mean of 0.74 ng/ml at baseline to 6.77 ng/ml 10 min after 10 puffs, reaching a mean maximum of 13.91 ng/ml by the end of the ad lib puffing period. Tobacco-related withdrawal symptoms and urge to smoke were significantly reduced; direct positive effects were strongly endorsed, and there was very low reporting of adverse effects. These findings demonstrate reliable blood nicotine delivery after the acute use of this brand/model of e-cigarette in a sample of regular users. Future studies might usefully quantify nicotine delivery in relation to inhalation technique and the relationship with successful smoking cessation/harm reduction.

A naturalistic examination of the perceived effects of cannabis on negative affect.

PubMed

Cuttler, Carrie; Spradlin, Alexander; McLaughlin, Ryan J

2018-08-01

Cannabis is commonly used to alleviate symptoms of negative affect. However, a paucity of research has examined the acute effects of cannabis on negative affect in everyday life. The current study provides a naturalistic account of perceived changes in symptoms of depression, anxiety, and stress as a function of dose and concentration of Δ 9 tetrahydrocannabinol (THC) and cannabidiol (CBD). Data from the app Strainprint TM (which provides medical cannabis users a means of tracking changes in symptoms as a function of different doses and chemotypes of cannabis) were analyzed using multilevel modeling. In total, 11,953 tracked sessions were analyzed (3,151 for depression, 5,085 for anxiety, and 3,717 for stress). Medical cannabis users perceived a 50% reduction in depression and a 58% reduction in anxiety and stress following cannabis use. Two puffs were sufficient to reduce ratings of depression and anxiety, while 10+ puffs produced the greatest perceived reductions in stress. High CBD (>9.5%)/low THC (<5.5%) cannabis was associated with the largest changes in depression ratings, while high CBD (>11%)/high THC (>26.5%) cannabis produced the largest perceived changes in stress. No changes in the perceived efficacy of cannabis were detected across time. However, baseline symptoms of depression (but not anxiety or stress) appeared to be exacerbated across time/tracked sessions. The primary limitations are the self-selected nature of the sample and the inability to control for expectancy effects. Cannabis reduces perceived symptoms of negative affect in the short-term, but continued use may exacerbate baseline symptoms of depression over time. Copyright © 2018 The Authors. Published by Elsevier B.V. All rights reserved.

Academic Value of Non-Academics: The Case for Keeping Extracurriculars

ERIC Educational Resources Information Center

Kronholz, June

2012-01-01

With school districts struggling to keep their noses above choppy budget waters and voters howling about taxes, should schools be funding Ping-Pong and trading-card clubs? Swim teams, moot court, powder puff football? Latino unions, gay-straight alliances, the Future Business Leaders of America, the French Honors Society, the jazz band, the…

Tonopah Test Range Flight Test

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

From a distance, the drop of a mock nuclear weapon — containing only non-nuclear components — was a mere puff of dust rising from a dry lake bed at Nevada’s Tonopah Test Range. However, it marked the start of a new series of test flights vital to the nation’s B61-12 weapon refurbishment program.

A study of mass loss from the mid-ultraviolet spectrum of Alpha Cygni /A2 Ia/, Beta Orionis /B8 Ia/, and Eta Leonis /A0 Ib/

NASA Technical Reports Server (NTRS)

Lamers, H. J. G. L. M.; Stalio, R.; Kondo, Y.

1978-01-01

Results are presented for a study of mass loss from A and late-B supergiants based on high-resolution mid-UV spectra obtained with the echelle spectrograph of the Balloon-borne Ultraviolet Stellar Spectrometer. Spectra of Alpha Cyg, Beta Ori, Eta Leo, and Alpha Lyr are compared in selected wavelength regions; particular attention is given to previous observations of each star, the Mg II and Fe II resonance lines, lines due to other ions, and evidence for mass ejection. The results indicate that mass loss from late-B and A supergiants is variable, that a considerable fraction of envelope material is ejected in 'puffs', and that the puffs may be due to photospheric instabilities. A mass-loss rate of about 1 hundred-millionth of a solar mass per year is derived for Alpha Cyg and shown to be two orders of magnitude smaller than the value determined from the observed IR excess. This discrepancy is attributed to excess ionization in the envelope.

Effects of Visual Information on Wind-Evoked Escape Behavior of the Cricket, Gryllus bimaculatus.

PubMed

Kanou, Masamichi; Matsuyama, Akane; Takuwa, Hiroyuki

2014-09-01

We investigated the effects of visual information on wind-evoked escape behavior in the cricket, Gryllus bimaculatus. Most agitated crickets were found to retreat into a shelter made of cardboard installed in the test arena within a short time. As this behavior was thought to be a type of escape, we confirmed how a visual image of a shelter affected wind-evoked escape behavior. Irrespective of the brightness of the visual background (black or white) or the absence or presence of a shelter, escape jumps were oriented almost 180° opposite to the source of the air puff stimulus. Therefore, the direction of wind-evoked escape depends solely depended on the direction of the stimulus air puff. In contrast, the turning direction of the crickets during the escape was affected by the position of the visual image of the shelter. During the wind-evoked escape jump, most crickets turned in the direction in which a shelter was presented. This behavioral nature is presumably necessary for crickets to retreat into a shelter within a short time after their escape jump.

Detection of nicotine content impact in tobacco manufacturing using computational intelligence.

PubMed

Begic Fazlic, Lejla; Avdagic, Zikrija

2011-01-01

A study is presented for the detection of nicotine impact in different cigarette type, using recorded data and Computational Intelligence techniques. Recorded puffs are processed using Continuous Wavelet Transform and used to extract time-frequency features for normal and abnormal puffs conditions. The wavelet energy distributions are used as inputs to classifiers based on Adaptive Neuro-Fuzzy Inference Systems (ANFIS) and Genetic Algorithms (GAs). The number and the parameters of Membership Functions are used in ANFIS along with the features from wavelet energy distributionare selected using GAs, maximising the diagnosis success. GA with ANFIS (GANFIS) are trained with a subset of data with known nicotine conditions. The trained GANFIS are tested using the other set of data (testing data). A classical method by High-Performance Liquid Chromatography is also introduced to solve this problem, respectively. The results as well as the performances of these two approaches are compared. A combination of these two algorithms is also suggested to improve the efficiency of this solution procedure. Computational results show that this combined algorithm is promising.

Influence of pre-drying treatments on physicochemical and organoleptic properties of explosion puff dried jackfruit chips.

PubMed

Yi, Jianyong; Zhou, Linyan; Bi, Jinfeng; Chen, Qinqin; Liu, Xuan; Wu, Xinye

2016-02-01

The effects of hot air drying (AD), freeze drying (FD), infrared drying (IR), microwave drying (MV), vacuum drying (VD) as pre-drying treatments for explosion puff drying (EPD) on qualities of jackfruit chips were studied. The lowest total color differences (∆E) were found in the FD-, MV- and VD-EPD dried chips. Volume expansion effect (9.2 %) was only observed in the FD-EPD dried chips, which corresponded to its well expanded honeycomb microstructures and high rehydration rate. Compared with AD-, IR-, MV- and VD-EPD, the FD-EPD dried fruit chips exhibited lower hardness and higher crispness, indicative of a crispier texture. FD-EPD dried fruits also obtained high retentions of ascorbic acid, phenolics and carotenoids compared with that of the other puffed products. The results of sensory evaluation suggested that the FD-EPD was a more beneficial combination because it enhanced the overall qualities of jackfruit chips. In conclusion, the FD-EPD could be used as a novel combination drying method for processing valuable and/or high quality fruit chips.

Effect of resistivity profile on current decay time of initial phase of current quench in neon-gas-puff inducing disruptions of JT-60U

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kawakami, S.; Ohno, N.; Shibata, Y.

2013-11-15

According to an early work [Y. Shibata et al., Nucl. Fusion 50, 025015 (2010)] on the behavior of the plasma current decay in the JT-60U disruptive discharges caused by the radiative collapse with a massive neon-gas-puff, the increase of the internal inductance mainly determined the current decay time of plasma current during the initial phase of current quench. To investigate what determines the increase of the internal inductance, we focus attention on the relationship between the electron temperature (or the resistivity) profile and the time evolution of the current density profile and carry out numerical calculations. As a result, wemore » find the reason of the increase of the internal inductance: The current density profile at the start of the current quench is broader than an expected current density profile in the steady state, which is determined by the temperature (or resistivity) profile. The current density profile evolves into peaked one and the internal inductance is increasing.« less

Young adult waterpipe smokers: Smoking behaviors and associated subjective and physiological effects.

PubMed

Shishani, Kawkab; Howell, Donelle; McPherson, Sterling; Roll, John

2014-06-01

The purpose of this pilot study was to investigate smoking behaviors and subjective and physiological effects of nicotine on young adult occasional waterpipe smokers. This study utilized a repeated-measures design that included one repeated factor for condition (nicotine and non-nicotine). For each participant, the sequencing of the repeated factor was assigned using random allocation. The two nicotine conditions were nicotine (0.75 g) and non-nicotine (0 g placebo) tobacco. Over the course of two weeks, twenty-two participants completed subjective (Acute Subjective Effects of Nicotine) and physiological (blood pressure, heart rate, and CO level) measures. Additional measures (QSU and MNWS-R) were used to assess for withdrawal symptoms. The participants (n=22) were young adults (23 ± 3.1years); 71% smoked waterpipe once a month in the past year and 29% smoked waterpipe 1-2 times per week. In addition, 60% reported sharing their waterpipe with friends while smoking. None of the participants reported using any other forms of tobacco products. Under the nicotine condition, participants tended to smoke longer (i.e. smoking duration, p=0.004), take more puffs (p=0.03), take shorter puffs (p=0.03), and inhale less volume with each puff (p=0.02). The repeated measures analysis of the factor headrush revealed an effect of the nicotine condition (F=9.69, p<0.001, partial η(2)=0.31) and time (F=8.17, p=0.02, partial η(2)=0.30). Heart rate increased significantly across the nicotine condition (F=7.92, p=0.01, partial η(2)=0.31) and over time (F=12.64, p=0.01, partial η(2)=0.41). This study demonstrates how differences between nicotine and non-nicotine waterpipe smoking are associated with changes in smoking behaviors, experiencing a headrush and an increase in heart rate. Copyright © 2014 Elsevier Ltd. All rights reserved.

Improved confinement in highly powered high performance scenarios on DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petrie, Thomas W.; Osborne, Thomas; Fenstermacher, Max E.

DIII-D has recently demonstrated improved energy confinement by injecting neutral deuterium gas into high performance near-double null divertor (DND) plasmas during high power operation. Representative parameters for these plasmas are: q 95 = 6, P IN up to 15 MW, H 98 = 1.4–1.8, and β N = 2.5–4.0. The ion B xmore » $$\\triangledown$$B direction is away from the primary X-point. While plasma conditions at lower to moderate power input (e.g., 11 MW) are shown to be favorable to successful puff-and-pump radiating divertor applications, particularly when using argon seeds, plasma behavior at higher powers (e.g., ≥14 MW) may make successful puff-and-pump operation more problematic. In contrast to lower powered high performance plasmas, both $$\\tau$$ E and β N in the high power cases (≥14 MW) increased and ELM frequency decreased, as density was raised by deuterium gas injection. Improved performance in the higher power plasmas was tied to higher pedestal pressure, which according to peeling-ballooning mode stability analysis using the ELITE code could increase with density along the kink/peeling stability threshold, while the pedestal pressure gradient in the lower power discharges were limited by the ballooning threshold. This resulted in improved fueling efficiency and ≈10% higher $$\\tau$$ E and β N than is normally observed in comparable high performance plasmas on DIII-D. Applying the puff-and-pump radiating divertor approach at moderate versus high power input is shown to result in a much different evolution in core and pedestal plasma behavior. In conclusion, we find that injecting deuterium gas into these highly powered DND plasmas may open up a new avenue for achieving elevated plasma performance, including better fueling, but the resulting higher density may also complicate application of a radiating divertor approach to heat flux reduction in present-day tokamaks, if scenarios involving second-harmonic electron cyclotron heating are used.« less

Simple Determination of Gaseous and Particulate Compounds Generated from Heated Tobacco Products.

PubMed

Uchiyama, Shigehisa; Noguchi, Mayumi; Takagi, Nao; Hayashida, Hideki; Inaba, Yohei; Ogura, Hironao; Kunugita, Naoki

2018-06-19

As a new form of cigarettes, heated tobacco products (HTPs) have been rapidly distributed worldwide. In this study, an improved method for analyzing gaseous and particulate compounds generated from HTPs is described. Smoke is collected using a GF-CX572 sorbent cartridge with 300 mg of carbon molecular sieves, that is, Carboxen 572 (CX572), and a 9 mm glass-fiber filter (GF). After collection, the CX572 particles from the cartridge are transferred along with the GF and deposited into a vial containing two phases of carbon disulfide and methanol. The CX572 particles settle into the lower carbon disulfide phase, while nonpolar compounds are desorbed. After the sample is allowed to stand, the solution is slowly stirred. The two-phase mixture of carbon disulfide and methanol is combined into a homogeneous solution. Polar compounds are then desorbed, while the desorbed nonpolar compounds remain in solution. For the analysis of carbonyl compounds, an enriched 2,4-dinitrophenylhydrazine solution is added to a portion of the combined solution for derivatization and subsequent high-performance liquid chromatography analysis. For the analysis of volatile organic compounds and water, a portion of the combined solution is analyzed by gas chromatography-mass spectrometry or equipped with a thermal conductivity detector. By applying the proposed GF-CX572 one-cartridge method to the analysis of the mainstream smoke generated from HTPs and traditional cigarettes, several chemical compounds are detected, and the chemical composition of smoke is revealed. The GF-CX572 one-cartridge method can analyze gaseous and particulate chemical compounds from the HTP smoke by utilizing not only the entire puff volume but also one puff volume because the GF-CX-572 cartridge can be replaced with a new cartridge within 3 s. An overview of the chemicals generated from HTPs is obtained in detail by one-puff volume sampling. In addition, the generated chemical compounds strongly depend on the temperature of tobacco leaves in HTPs.

Reduced Exposure to Harmful and Potentially Harmful Smoke Constituents With the Tobacco Heating System 2.1

PubMed Central

Baker, Gizelle; Magnette, John; Picavet, Patrick; Weitkunat, Rolf

2017-01-01

Introduction: Heating rather than burning tobacco reduces levels of harmful and potentially harmful constituents, and consumer products using this approach aim to reduce exposure to tobacco toxicants. The Tobacco Heating System (THS) version 2.1 has been enhanced from earlier prototypes with an improved heat control and sensorial experience and thereby user acceptance. Exposure measurements are required to determine whether it may be possible to reduce the individual health risk compared to smoking combustible cigarettes (CCs). Methods: This controlled clinical study randomly assigned 40 smokers to either a group continuing to use of their own CC brand (n = 20) or a group switching to THS 2.1 (n = 20) for 5 days. Biomarkers of exposure were measured at baseline and on day 1 through day 5. Product consumption, Human Puffing Topography, the occurrence of adverse events, and an assessment of subjective effects, such as smoking satisfaction and enjoyment of respiratory tract sensations, were also determined. Results: The group of smokers who switched to THS 2.1 adapted their puffing behavior initially through longer puff duration and more puffs. During the duration of the study, total puff volume returned to baseline levels and the mean daily product consumption increased but with similar nicotine exposure compared to baseline CC use. Biomarkers of exposure to tobacco smoke toxicants which inform product risk assessment were significantly reduced with THS use compared to the CC group. THS 2.1 users experienced less reinforcing effects with THS 2.1 than with their own cigarette brand. Conclusions: THS 2.1 is a promising alternative to smoking CCs. Notwithstanding possible use adaption through consumption or puffing behavior, the exposure to harmful smoke constituents was markedly reduced with the new heated tobacco platform. Implications: Exposure markers to harmful and potentially harmful smoke constituents were lowered with the THS 2.1. Heating tobacco instead of burning can offer a potentially lower risk of delivering nicotine compared to CCs. PMID:27613951

Effect of retinal impulse blockage on cytochrome oxidase-poor interpuffs in the macaque striate cortex: quantitative EM analysis of neurons.

PubMed

Wong-Riley, M T; Trusk, T C; Kaboord, W; Huang, Z

1994-09-01

One of the hallmarks of the primate striate cortex is the presence of cytochrome oxidase-rich puffs in its supragranular layers. Neurons in puffs have been classified as type A, B, and C in ascending order of cytochrome oxidase content, with type C cells being the most vulnerable to retinal impulse blockade. The present study aimed at analysing cytochrome oxidase-poor interpuffs with reference to their metabolic cell types and the effect of intraretinal tetrodotoxin treatment. The same three metabolic types were found in interpuffs, except that type B and C neurons were smaller and less cytochrome oxidase-reactive in interpuffs than in puffs. Type A neurons had small perikarya, low levels of cytochrome oxidase, and received exclusively symmetric axosomatic synapses. The largest neurons were pyramidal, type B cells with moderate cytochrome oxidase activity and were also contacted exclusively by symmetric axosomatic synapses. Type C cells medium-sized with a rich supply of large, darkly reactive mitochondria and possessed all the characteristics of GABAergic neurons. They were the only cell type that received both symmetric and asymmetric axosomatic synapses. Two weeks of monocular tetrodotoxin blockade in adult monkeys caused all three major cell types in deprived interpuffs to suffer a significant downward shift in the size and cytochrome oxidase reactivity of their mitochondria, but the effects were more severe in type B and C neurons. In nondeprived interpuffs, all three cell types gained both in size and absolute number of mitochondria, and type A cells also had an elevated level of cytochrome oxidase, indicating that they might be functioning at a competitive advantage over cells in deprived columns. However, type B and C neurons showed a net loss of darkly reactive mitochondria, indicating that these cells became less active. Thus, mature interpuff neurons remained vulnerable to retinal impulse blockade and the metabolic capacity of these cells remains tightly regulated by neuronal activity.

Quantitative assessment of corneal vibrations during intraocular pressure measurement with the air-puff method in patients with keratoconus.

PubMed

Koprowski, Robert; Ambrósio, Renato

2015-11-01

One of the current methods for measuring intraocular pressure is the air-puff method. A tonometer which uses this method is the Corvis device. With the ultra-high-speed (UHS) Scheimpflug camera, it is also possible to observe corneal deformation during measurement. The use of modern image analysis and processing methods allows for analysis of higher harmonics of corneal deflection above 100 Hz. 493 eyes of healthy subjects and 279 eyes of patients with keratoconus were used in the measurements. For each eye, 140 corneal deformation images were recorded during intraocular pressure measurement. Each image was recorded every 230 µs and had a resolution of 200 × 576 pixels. A new, original algorithm for image analysis and processing has been proposed. It enables to separate the eyeball reaction as well as low-frequency and high-frequency corneal deformations from the eye response to an air puff. Furthermore, a method for classification of healthy subjects and patients with keratoconus based on decision trees has been proposed. The obtained results confirm the possibility to distinguish between patients with keratoconus and healthy subjects. The features used in this classification are directly related to corneal vibrations. They are only available in the proposed software and provide specificity of 98%, sensitivity-85%, and accuracy-92%. This confirms the usefulness of the proposed method in this type of classification that uses corneal vibrations during intraocular pressure measurement with the Corvis tonometer. With the new proposed algorithm for image analysis and processing allowing for the separation of individual features from a corneal deformation image, it is possible to: automatically measure corneal vibrations in a few characteristic points of the cornea, obtain fully repeatable measurement of vibrations for the same registered sequence of images and measure vibration parameters for large inter-individual variability in patients. Copyright © 2015 Elsevier Ltd. All rights reserved.

Are metals emitted from electronic cigarettes a reason for health concern? A risk-assessment analysis of currently available literature.

PubMed

Farsalinos, Konstantinos E; Voudris, Vassilis; Poulas, Konstantinos

2015-05-15

Studies have found that metals are emitted to the electronic cigarette (EC) aerosol. However, the potential health impact of exposure to such metals has not been adequately defined. The purpose of this study was to perform a risk assessment analysis, evaluating the exposure of electronic cigarette (EC) users to metal emissions based on findings from the published literature. Two studies were found in the literature, measuring metals emitted to the aerosol from 13 EC products. We estimated that users take on average 600 EC puffs per day, but we evaluated the daily exposure from 1200 puffs. Estimates of exposure were compared with the chronic Permissible Daily Exposure (PDE) from inhalational medications defined by the U.S. Pharmacopeia (cadmium, chromium, copper, lead and nickel), the Minimal Risk Level (MRL) defined by the Agency for Toxic Substances and Disease Registry (manganese) and the Recommended Exposure Limit (REL) defined by the National Institute of Occupational Safety and Health (aluminum, barium, iron, tin, titanium, zinc and zirconium). The average daily exposure from 13 EC products was 2.6 to 387 times lower than the safety cut-off point of PDEs, 325 times lower than the safety limit of MRL and 665 to 77,514 times lower than the safety cut-off point of RELs. Only one of the 13 products was found to result in exposure 10% higher than PDE for one metal (cadmium) at the extreme daily use of 1200 puffs. Significant differences in emissions between products were observed. Based on currently available data, overall exposure to metals from EC use is not expected to be of significant health concern for smokers switching to EC use, but is an unnecessary source of exposure for never-smokers. Metal analysis should be expanded to more products and exposure can be further reduced through improvements in product quality and appropriate choice of materials.

Cross-sectional and prospective relation of cannabis potency, dosing and smoking behaviour with cannabis dependence: an ecological study.

PubMed

van der Pol, Peggy; Liebregts, Nienke; Brunt, Tibor; van Amsterdam, Jan; de Graaf, Ron; Korf, Dirk J; van den Brink, Wim; van Laar, Margriet

2014-07-01

Increased delta-9-tetrahydrocannabinol (THC) concentrations in cannabis may lead to higher THC exposure, cannabis dependence and treatment need, but users may also adapt the actual intake of THC through reduced inhalation of THC containing smoke (titration). We investigated whether consumers of stronger cannabis use less cannabis per joint or inhale less smoke than those using less potent cannabis and whether these factors predict cannabis dependence severity. Heavy cannabis users (n = 98) brought their own cannabis, rolled a joint and smoked it ad libitum in a naturalistic setting. We analysed the content of the joint, its association with smoking behaviour and the cross-sectional and prospective (1.5-year follow-up) relations between smoking behaviour and cannabis dependence severity (total number of DSM-IV dependence symptoms). THC concentration in cannabis (range 1.10-24.70%) was correlated positively with cannabis dose per joint (b = 0.008, P = 0.01), but the resulting THC concentration per joint (range 0.24-15.72%) was associated negatively with inhalation volume (b = -0.05, P = 0.03). Smoking behaviour measures (number of puffs, inhaled volume, reduction of puff volume and puff duration while smoking) predicted follow-up dependence severity, independently of baseline dependence severity and monthly THC dose (number of joints × cannabis dose × cannabis THC concentration). Monthly THC dose only predicted follow-up dependence severity when unadjusted for baseline severity. Cannabis users titrate their delta-9-tetrahydrocannabinol intake by inhaling lower volumes of smoke when smoking strong joints, but this does not fully compensate for the higher cannabis doses per joint when using strong cannabis. Thus, users of more potent cannabis are generally exposed to more delta-9-tetrahydrocannabinol. Smoking behaviour appears to be a stronger predictor for cannabis dependence severity than monthly delta-9-tetrahydrocannabinol dose. © 2014 Society for the Study of Addiction.

Improved confinement in highly powered high performance scenarios on DIII-D

DOE PAGES

Petrie, Thomas W.; Osborne, Thomas; Fenstermacher, Max E.; ...

2017-06-09

DIII-D has recently demonstrated improved energy confinement by injecting neutral deuterium gas into high performance near-double null divertor (DND) plasmas during high power operation. Representative parameters for these plasmas are: q 95 = 6, P IN up to 15 MW, H 98 = 1.4–1.8, and β N = 2.5–4.0. The ion B xmore » $$\\triangledown$$B direction is away from the primary X-point. While plasma conditions at lower to moderate power input (e.g., 11 MW) are shown to be favorable to successful puff-and-pump radiating divertor applications, particularly when using argon seeds, plasma behavior at higher powers (e.g., ≥14 MW) may make successful puff-and-pump operation more problematic. In contrast to lower powered high performance plasmas, both $$\\tau$$ E and β N in the high power cases (≥14 MW) increased and ELM frequency decreased, as density was raised by deuterium gas injection. Improved performance in the higher power plasmas was tied to higher pedestal pressure, which according to peeling-ballooning mode stability analysis using the ELITE code could increase with density along the kink/peeling stability threshold, while the pedestal pressure gradient in the lower power discharges were limited by the ballooning threshold. This resulted in improved fueling efficiency and ≈10% higher $$\\tau$$ E and β N than is normally observed in comparable high performance plasmas on DIII-D. Applying the puff-and-pump radiating divertor approach at moderate versus high power input is shown to result in a much different evolution in core and pedestal plasma behavior. In conclusion, we find that injecting deuterium gas into these highly powered DND plasmas may open up a new avenue for achieving elevated plasma performance, including better fueling, but the resulting higher density may also complicate application of a radiating divertor approach to heat flux reduction in present-day tokamaks, if scenarios involving second-harmonic electron cyclotron heating are used.« less

Bacterial contaminants from frozen puff pastry production process and their growth inhibition by antimicrobial substances from lactic acid bacteria.

PubMed

Rumjuankiat, Kittaporn; Keawsompong, Suttipun; Nitisinprasert, Sunee

2017-05-01

Seventy-five bacterial contaminants which still persisted to cleaning system from three puff pastry production lines (dough forming, layer and filling forming, and shock freezing) were identified using 16S rDNA as seven genera of Bacillus , Corynebacterium , Dermacoccus , Enterobacter , Klebsiella, Pseudomonas , and Staphylococcus with detection frequencies of 24.00, 2.66, 1.33, 37.33, 1.33, 2.66, and 30.66, respectively. Seventeen species were discovered while only 11 species Bacillus cereus, B. subtilis, B. pumilus, Corynebacterium striatum , Dermacoccus barathri , Enterobacter asburiae, Staphylococcus kloosii, S. haemolyticus, S. hominis, S. warneri , and S. aureus were detected at the end of production. Based on their abundance, the highest abundance of E. asburiae could be used as a biomarker for product quality. While a low abundance of the mesophile pathogen C. striatum , which causes respiratory and nervous infection and appeared only at the shock freezing step was firstly reported for its detection in bakery product. Six antimicrobial substances (AMSs) from lactic acid bacteria, FF1-4, FF1-7, PFUR-242, PFUR-255, PP-174, and nisin A were tested for their inhibition activities against the contaminants. The three most effective were FF1-7, PP-174, and nisin A exhibiting wide inhibition spectra of 88.00%, 85.33%, and 86.66%, respectively. The potential of a disinfectant solution containing 800 AU/ml of PP-174 and nisin A against the most resistant strains of Enterobacter , Staphylococcus , Bacillus and Klebsiella was determined on artificially contaminated conveyor belt coupons at 0, 4, 8, 12, and 16 hr. The survival levels of the test strains were below 1 log CFU/coupon at 0 hr. The results suggested that a combined solution of PP-174 and nisin A may be beneficial as a sanitizer to inhibit bacterial contaminants in the frozen puff pastry industry.

Carbonyl emissions from a novel heated tobacco product (IQOS): comparison with an e-cigarette and a tobacco cigarette.

PubMed

Farsalinos, Konstantinos E; Yannovits, Nikoletta; Sarri, Theoni; Voudris, Vassilis; Poulas, Konstantinos; Leischow, Scott

2018-06-19

To measure carbonyl emissions from a heated tobacco product (IQOS) in comparison with an e-cigarette (Nautilus Mini) and a commercial tobacco cigarette (Marlboro Red). Regular and menthol variants of the heated tobacco product were tested. A tank-type atomizer was tested with a tobacco-flavoured liquid at 10 W and 14 W. Aerosol and smoke were collected in impingers containing 2,4-dinitrophenylhydrazine. Health Canada Intense and two more intense puffing regimes were used. Analytical laboratory in Greece. Carbonyl levels in the aerosol and smoke. At Health Canada Intense regime, heated tobacco products emitted 5.0-6.4 μg/stick formaldehyde, 144.1-176.7 μg/stick acetaldehyde, 10.4-10.8 μg/stick acrolein, 11.0-12.8 μg/stick propionaldehyde and 1.9-2.0 μg/stick crotonaldehyde. Compared with the tobacco cigarette, levels were on average 91.6% lower for formaldehyde, 84.9% lower for acetaldehyde, 90.6% lower for acrolein, 89.0% lower for propionaldehyde and 95.3% lower for crotonaldehyde. The e-cigarette emitted 0.5-1.0 μg/12 puffs formaldehyde, 0.8-1.5μg/12 puffs acetaldehyde and 0.3-0.4 μg/12 puffs acrolein, but no propionaldehyde and crotonaldehyde. At more intense puffing regimes, formaldehyde was increased in heated tobacco products, but levels were 3 to 4-fold lower compared with the tobacco cigarette. Based on the findings from Health Canada Intense puffing regime, use of 20 heated tobacco sticks would result in 81.7-97.9% reduced carbonyl exposure compared with smoking 20 tobacco cigarettes; the respective reduction in exposure from use of 5 g e-cigarette liquid would be 92.2-99.8%. The IQOS heated tobacco product emits substantially lower levels of carbonyls than a commercial tobacco cigarette (Marlboro Red) but higher levels than a Nautilus Mini e-cigarette. This article is protected by copyright. All rights reserved.

One- and two-dimensional modeling of argon K-shell emission from gas-puff Z-pinch plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thornhill, J. W.; Chong, Y. K.; Apruzese, J. P.

2007-06-15

In this paper, a theoretical model is described and demonstrated that serves as a useful tool for understanding K-shell radiating Z-pinch plasma behavior. Such understanding requires a self-consistent solution to the complete nonlocal thermodynamic equilibrium kinetics and radiation transport in order to realistically model opacity effects and the high-temperature state of the plasma. For this purpose, we have incorporated into the MACH2 two-dimensional magnetohydrodynamic (MHD) code [R. E. Peterkin et al., J. Comput. Phys. 140, 148 (1998)] an equation of state, called the tabular collisional radiative equilibrium (TCRE) model [J. W. Thornhill et al., Phys. Plasmas 8, 3480 (2001)], thatmore » provides reasonable approximations to the plasma's opacity state. MACH2 with TCRE is applied toward analyzing the multidimensional implosion behavior that occurred in Decade Quad (DQ) [D. Price et al., Proceedings of the 12th IEEE Pulsed Power Conference, Monterey, CA, edited by C. Stallings and H. Kirbie (IEEE, New York, 1999), p. 489] argon gas puff experiments that employed a 12 cm diameter nozzle with and without a central gas jet on axis. Typical peak drive currents and implosion times in these experiments were {approx}6 MA and {approx}230 ns. By using Planar Laser Induced Fluorescence measured initial density profiles as input to the calculations, the effect these profiles have on the ability of the pinch to efficiently produce K-shell emission can be analyzed with this combined radiation-MHD model. The calculated results are in agreement with the experimental result that the DQ central-jet configuration is superior to the no-central-jet experiment in terms of producing more K-shell emission. These theoretical results support the contention that the improved operation of the central-jet nozzle is due to the better suppression of instabilities and the higher-density K-shell radiating conditions that the central-jet configuration promotes. When we applied the model toward projecting argon K-shell yield behavior for Sandia National Laboratories' ZR machine ({approx}25 MA peak drive currents, {approx}100 ns implosion times) [D. McDaniel et al., Proceedings of the 5th International Conference on Dense Z-Pinches, Albuquerque, NM, 2002, edited by J. Davis, C. Deeney, and N. R. Pereira (American Institute of Physics, New York, 2002), Vol. 651, p. 23] for experiments that utilize the 12 cm diameter central-jet nozzle configuration, it predicts over 1 MJ of K-shell emission is attainable.« less

Assimilating concentration observations for transport and dispersion modeling in a meandering wind field

NASA Astrophysics Data System (ADS)

Haupt, Sue Ellen; Beyer-Lout, Anke; Long, Kerrie J.; Young, George S.

Assimilating concentration data into an atmospheric transport and dispersion model can provide information to improve downwind concentration forecasts. The forecast model is typically a one-way coupled set of equations: the meteorological equations impact the concentration, but the concentration does not generally affect the meteorological field. Thus, indirect methods of using concentration data to influence the meteorological variables are required. The problem studied here involves a simple wind field forcing Gaussian dispersion. Two methods of assimilating concentration data to infer the wind direction are demonstrated. The first method is Lagrangian in nature and treats the puff as an entity using feature extraction coupled with nudging. The second method is an Eulerian field approach akin to traditional variational approaches, but minimizes the error by using a genetic algorithm (GA) to directly optimize the match between observations and predictions. Both methods show success at inferring the wind field. The GA-variational method, however, is more accurate but requires more computational time. Dynamic assimilation of a continuous release modeled by a Gaussian plume is also demonstrated using the genetic algorithm approach.

Helping Teenagers Stop Smoking: Comparative Observations across Youth Settings in Cardiff

ERIC Educational Resources Information Center

Bowles, Hannah; Maher, Alison; Sage, Robert

2009-01-01

Objective: This paper presents comparative observations between schools/colleges, youth centres, and specialist youth provision, in relation to delivery of the 2tuff2puff six-week smoking cessation and awareness programme to young people in Cardiff. Design: A six-week smoking cessation programme was delivered to 12-23 year olds in various youth…

We Huff and Puff: The Parameters and the Program of Aerobics for Children under Five.

ERIC Educational Resources Information Center

Eastman, Wayne

In today's society, young children have few experiences with aerobic activities, a pattern of exercise traditionally reserved for adults. This paper discusses how aerobic exercises can be used in a preschool environment, arguing that such activities are best presented using a thematic approach so that young children can form impressions about…

Food Service Worker. Instructional Modules for Food Management, Production and Services. Modules 35-52. Competency Based Curriculum.

ERIC Educational Resources Information Center

Tennessee Univ., Knoxville. Dept. of Vocational-Technical Education.

These 18 teacher modules are part of a curriculum dealing with food management, production, and services that was developed for use in secondary and postsecondary vocational programs in Tennessee. Covered in the individual modules are quickbreads, pies, icings and toppings, specialty cakes, specialty desserts, yeast products, cream puff and puff…

Parameter dependences of the separatrix density in nitrogen seeded ASDEX Upgrade H-mode discharges

NASA Astrophysics Data System (ADS)

Kallenbach, A.; Sun, H. J.; Eich, T.; Carralero, D.; Hobirk, J.; Scarabosio, A.; Siccinio, M.; ASDEX Upgrade Team; EUROfusion MST1 Team

2018-04-01

The upstream separatrix electron density is an important interface parameter for core performance and divertor power exhaust. It has been measured in ASDEX Upgrade H-mode discharges by means of Thomson scattering using a self-consistent estimate of the upstream electron temperature under the assumption of Spitzer-Härm electron conduction. Its dependence on various plasma parameters has been tested for different plasma conditions in H-mode. The leading parameter determining n e,sep was found to be the neutral divertor pressure, which can be considered as an engineering parameter since it is determined mainly by the gas puff rate and the pumping speed. The experimentally found parameter dependence of n e,sep, which is dominated by the divertor neutral pressure, could be approximately reconciled by 2-point modelling.

Application of fuzzy set theory for integral assessment of agricultural products quality

NASA Astrophysics Data System (ADS)

Derkanosova, N. M.; Ponomareva, I. N.; Shurshikova, G. V.; Vasilenko, O. A.

2018-05-01

The methodology of integrated assessment of quality and safety of agricultural products, approbated by the example of indicators of wheat grain in relation to the provision of consumer properties of bakery products, was developed. Determination of the level of quality of the raw ingredients will allow direct using of agricultural raw materials for food production, taking into account ongoing technology, types of products, and, respectively, rational use of resource potential of the agricultural sector. The mathematical tool of the proposed method is a fuzzy set theory. The fuzzy classifier to evaluate the properties of the grain is formed. The set of six indicators normalized by the national standard is determined; values are ordered and represented by linguistic variables with a trapeziform membership function; the rules for calculation of membership functions are presented. Specific criteria values for individual indicators in shaping the quality of the finished products are considered. For one of the samples of wheat grain values of membership; functions of the linguistic variable "level" for all indicators and the linguistic variable "level of quality" were calculated. It is established that the studied sample of grain obtains the 2 (average) level of quality. Accordingly, it can be recommended for the production of bakery products with higher requirements for the structural-mechanical properties bakery and puff pastry products hearth bread and flour confectionery products of the group of hard dough cookies and crackers

Detection of significant differences between absorption spectra of neutral helium and low temperature photoionized helium plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartnik, A.; Wachulak, P.; Fiedorowicz, H.

2013-11-15

In this work, spectral investigations of photoionized He plasmas were performed. The photoionized plasmas were created by irradiation of helium stream, with intense pulses from laser-plasma extreme ultraviolet (EUV) source. The EUV source was based on a double-stream Xe/Ne gas-puff target irradiated with 10 ns/10 J Nd:YAG laser pulses. The most intense emission from the source spanned a relatively narrow spectral region below 20 nm, however, spectrally integrated intensity at longer wavelengths was also significant. The EUV radiation was focused onto a gas stream, injected into a vacuum chamber synchronously with the EUV pulse. The long-wavelength part of the EUVmore » radiation was used for backlighting of the photoionized plasmas to obtain absorption spectra. Both emission and absorption spectra in the EUV range were investigated. Significant differences between absorption spectra acquired for neutral helium and low temperature photoionized plasmas were demonstrated for the first time. Strong increase of intensities and spectral widths of absorption lines, together with a red shift of the K-edge, was shown.« less

Image processing and computer controls for video profile diagnostic system in the ground test accelerator (GTA)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, R.M.; Zander, M.E.; Brown, S.K.

1992-09-01

This paper describes the application of video image processing to beam profile measurements on the Ground Test Accelerator (GTA). A diagnostic was needed to measure beam profiles in the intermediate matching section (IMS) between the radio-frequency quadrupole (RFQ) and the drift tube linac (DTL). Beam profiles are measured by injecting puffs of gas into the beam. The light emitted from the beam-gas interaction is captured and processed by a video image processing system, generating the beam profile data. A general purpose, modular and flexible video image processing system, imagetool, was used for the GTA image profile measurement. The development ofmore » both software and hardware for imagetool and its integration with the GTA control system (GTACS) will be discussed. The software includes specialized algorithms for analyzing data and calibrating the system. The underlying design philosophy of imagetool was tested by the experience of building and using the system, pointing the way for future improvements. The current status of the system will be illustrated by samples of experimental data.« less

Image processing and computer controls for video profile diagnostic system in the ground test accelerator (GTA)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, R.M.; Zander, M.E.; Brown, S.K.

1992-01-01

This paper describes the application of video image processing to beam profile measurements on the Ground Test Accelerator (GTA). A diagnostic was needed to measure beam profiles in the intermediate matching section (IMS) between the radio-frequency quadrupole (RFQ) and the drift tube linac (DTL). Beam profiles are measured by injecting puffs of gas into the beam. The light emitted from the beam-gas interaction is captured and processed by a video image processing system, generating the beam profile data. A general purpose, modular and flexible video image processing system, imagetool, was used for the GTA image profile measurement. The development ofmore » both software and hardware for imagetool and its integration with the GTA control system (GTACS) will be discussed. The software includes specialized algorithms for analyzing data and calibrating the system. The underlying design philosophy of imagetool was tested by the experience of building and using the system, pointing the way for future improvements. The current status of the system will be illustrated by samples of experimental data.« less

Plume Tracker: A New Toolkit for the Mapping of Volcanic Plumes with Multispectral Thermal Infrared Remote Sensing

NASA Astrophysics Data System (ADS)

Realmuto, V. J.; Baxter, S.; Webley, P. W.

2011-12-01

Plume Tracker is the next generation of interactive plume mapping tools pioneered by MAP_SO2. First developed in 1995, MAP_SO2 has been used to study plumes at a number of volcanoes worldwide with data acquired by both airborne and space-borne instruments. The foundation of these tools is a radiative transfer (RT) model, based on MODTRAN, which we use as the forward model for our estimation of ground temperature and sulfur dioxide concentration. Plume Tracker retains the main functions of MAP_SO2, providing interactive tools to input radiance measurements and ancillary data, such as profiles of atmospheric temperature and humidity, to the retrieval procedure, generating the retrievals, and visualizing the resulting retrievals. Plume Tracker improves upon MAP_SO2 in the following areas: (1) an RT model based on an updated version of MODTRAN, (2) a retrieval procedure based on maximizing the vector projection of model spectra onto observed spectra, rather than minimizing the least-squares misfit between the model and observed spectra, (3) an ability to input ozone profiles to the RT model, (4) increased control over the vertical distribution of the atmospheric gas species used in the model, (5) a standard programmatic interface to the RT model code, based on the Component Object Model (COM) interface, which will provide access to any programming language that conforms to the COM standard, and (6) a new binning algorithm that decreases running time by exploiting spatial redundancy in the radiance data. Based on our initial testing, the binning algorithm can reduce running time by an order of magnitude. The Plume Tracker project is a collaborative effort between the Jet Propulsion Laboratory and Geophysical Institute (GI) of the University of Alaska-Fairbanks. Plume Tracker is integrated into the GI's operational plume dispersion modeling system and will ingest temperature and humidity profiles generated by the Weather Research and Forecasting model, together with plume height estimates from the Puff model. The access to timely forecasts of atmospheric conditions, together with the reductions in running time, will increase the utility of Plume Tracker in the Alaska Volcano Observatory's mission to mitigate volcanic hazards in Alaska and the Northern Pacific region.

33 CFR 334.410 - Albemarle Sound, Pamlico Sound, and adjacent waters, NC; danger zones for naval aircraft operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... bombs which contain only small explosive charges for producing smoke puffs to mark points of impact. All... operations. Dummy ammunition, waterfilled or smoke bombs and inert rockets will be used, except during wartime when live ammunition, bombs and rockets may be used. The area will be open to navigation except...

Eye-Blink Conditioning Is Associated with Changes in Synaptic Ultrastructure in the Rabbit Interpositus Nuclei

ERIC Educational Resources Information Center

Weeks, Andrew C. W.; Connor, Steve; Hinchcliff, Richard; LeBoutillier, Janelle C.; Thompson, Richard F.; Petit, Ted L.

2007-01-01

Eye-blink conditioning involves the pairing of a conditioned stimulus (usually a tone) to an unconditioned stimulus (air puff), and it is well established that an intact cerebellum and interpositus nucleus, in particular, are required for this form of classical conditioning. Changes in synaptic number or structure have long been proposed as a…

Plasma shut-down with fast impurity puff on ASDEX Upgrade

NASA Astrophysics Data System (ADS)

Pautasso, G.; Fuchs, C. J.; Gruber, O.; Maggi, C. F.; Maraschek, M.; Pütterich, T.; Rohde, V.; Wittmann, C.; Wolfrum, E.; Cierpka, P.; Beck, M.; ASDEX Upgrade Team

2007-08-01

The massive injection of impurity gas into a plasma has been proved to reduce forces and localized thermal loads caused by disruptions in tokamaks. This mitigation system is routinely used on ASDEX Upgrade to shut down plasmas with a locked mode. The plasma response to impurity injection and the mechanism of reduction of the mechanical forces is discussed in the paper.

33 CFR 334.410 - Albemarle Sound, Pamlico Sound, and adjacent waters, NC; danger zones for naval aircraft operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... bombs which contain only small explosive charges for producing smoke puffs to mark points of impact. All... operations. Dummy ammunition, waterfilled or smoke bombs and inert rockets will be used, except during wartime when live ammunition, bombs and rockets may be used. The area will be open to navigation except...

33 CFR 334.410 - Albemarle Sound, Pamlico Sound, and adjacent waters, NC; danger zones for naval aircraft operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... bombs which contain only small explosive charges for producing smoke puffs to mark points of impact. All... operations. Dummy ammunition, waterfilled or smoke bombs and inert rockets will be used, except during wartime when live ammunition, bombs and rockets may be used. The area will be open to navigation except...

33 CFR 334.410 - Albemarle Sound, Pamlico Sound, and adjacent waters, NC; danger zones for naval aircraft operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... bombs which contain only small explosive charges for producing smoke puffs to mark points of impact. All... operations. Dummy ammunition, waterfilled or smoke bombs and inert rockets will be used, except during wartime when live ammunition, bombs and rockets may be used. The area will be open to navigation except...

SRI PUFF 8 Computer Program for One-Dimensional Stress Wave Propagation

DTIC Science & Technology

1980-03-01

raial product. UNCLASSIFIED SECURITY CLASSIFICATION OF THIS PAGE (Tfhen Data Entered) REPORT DOCUMENTATION PAGE READ INSTRUCTIONS BEFORE COMPLETING...EDITION OF I NOV 6S (S OBSOLETE UNCLASSIFIED SECURITY CLASSIFICATIOK OF THIS PAGE (When Data Entered) UNCLASSIFIED SECURITY CLASSIFICATION OF THIS...aspects of wave propagation calculations. UNCLASSIFIED SECURITY CLASSIFICATION OF THIS PAGEfWhen Data Entered) FOREWORD This volume constitutes a

Correction on the distortion of Scheimpflug imaging for dynamic central corneal thickness

NASA Astrophysics Data System (ADS)

Li, Tianjie; Tian, Lei; Wang, Like; Hon, Ying; Lam, Andrew K. C.; Huang, Yifei; Wang, Yuanyuan; Zheng, Yongping

2015-05-01

The measurement of central corneal thickness (CCT) is important in ophthalmology. Most studies concerned the value at normal status, while rare ones focused on its dynamic changing. The commercial Corvis ST is the only commercial device currently available to visualize the two-dimensional image of dynamic corneal profiles during an air puff indentation. However, the directly observed CCT involves the Scheimpflug distortion, thus misleading the clinical diagnosis. This study aimed to correct the distortion for better measuring the dynamic CCTs. The optical path was first derived to consider the influence of factors on the use of Covis ST. A correction method was then proposed to estimate the CCT at any time during air puff indentation. Simulation results demonstrated the feasibility of the intuitive-feasible calibration for measuring the stationary CCT and indicated the necessity of correction when air puffed. Experiments on three contact lenses and four human corneas verified the prediction that the CCT would be underestimated when the improper calibration was conducted for air and overestimated when it was conducted on contact lenses made of polymethylmethacrylate. Using the proposed method, the CCT was finally observed to increase by 66±34 μm at highest concavity in 48 normal human corneas.

Behavioral analyses of wind-evoked escape of the cricket, Gryllodes sigillatus.

PubMed

Kanou, Masamichi; Konishi, Atsuko; Suenaga, Rie

2006-04-01

The wind-evoked escape behavior of the cricket Gryllodes sigillatus was investigated using an air puff stimulus. A high velocity air puff elicited the escape behavior in many crickets. The crickets tended to escape away from the stimulus source, but the direction was not accurately oriented 180 degrees from the stimulus. After bilateral cercal ablation, only a few crickets showed wind-evoked escape behavior, and their response rates did not increase even 19 days after ablation. Therefore, information on air motion detected by cercal filiform hairs is essential for triggering wind-evoked behavior. After unilateral cercal ablation, the 81.3% response rate of intact crickets decreased to 16.5%, that is, it decreased to almost 20% that of intact crickets. One week after unilateral cercal ablation, the response rate recovered to more than 60% that of intact crickets. However, the accuracy rate of the escape direction of G. sigillatus showed no change even immediately after the unilateral cercal ablation. Therefore, both cerci are not necessarily required to determine the escape direction. The behavioral characteristics of wind-evoked escape of G. sigillatus are compared with those of another species of cricket, Gryllus bimaculatus. The two species of cricket employ different strategies for wind-evoked escape.

Stable isotope studies of nicotine kinetics and bioavailability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benowitz, N.L.; Jacob, P. 3d.; Denaro, C.

1991-03-01

The stable isotope-labeled compound 3',3'-dideuteronicotine was used to investigate the disposition kinetics of nicotine in smokers, the systemic absorption of nicotine from cigarette smoke, and the bioavailability of nicotine ingested as oral capsules. Blood levels of labeled nicotine could be measured for 9 hours after a 30-minute intravenous infusion. Analysis of disposition kinetics in 10 healthy men revealed a multiexponential decline after the end of an infusion, with an elimination half-life averaging 203 minutes. This half-life was longer than that previously reported, indicating the presence of a shallow elimination phase. Plasma clearance averaged 14.6 ml/min/kg. The average intake of nicotinemore » per cigarette was 2.29 mg. A cigarette smoke-monitoring system that directly measured particulate matter in smoke was evaluated in these subjects. Total particulate matter, number of puffs on the cigarette, total puff volume, and time of puffing correlated with the intake of nicotine from smoking. The oral bioavailability of nicotine averaged 44%. This bioavailability is higher than expected based on the systemic clearance of nicotine and suggests that there may be significant extrahepatic metabolism of nicotine.« less

Effects of fenoterol and ipratropium on respiratory resistance of asthmatics after tracheal intubation.

PubMed

Wu, R S; Wu, K C; Wong, T K; Tsai, Y H; Cheng, R K; Bishop, M J; Tan, P P

2000-03-01

We have studied the effects of a beta-agonist, fenoterol, and a cholinergic antagonist, ipratropium, on post-intubation total respiratory system resistance (Rrs) in asthmatics who developed increased Rrs after tracheal intubation. Sixteen stable asthmatics in whom Rrs increased after intubation were allocated randomly to receive either 10 puffs of fenoterol (group F) or 10 puffs of ipratropium (group IB) via a metered dose inhaler 5 min after intubation. Anaesthesia was induced and maintained with propofol i.v. Rrs was recorded before treatment and again 5, 15 and 30 min after treatment. Rrs decreased significantly from pretreatment values by mean 53 (SD 8)%, 53 (7)% and 58 (6)% at 5, 15 and 30 min, respectively, in group F, but declined by only 12 (6)%, 15 (4)% and 17 (5)% in group IB. At all times after treatment, patients in the fenoterol group had significantly lower Rrs values than those in the ipratropium group. We conclude that increased Rrs after tracheal intubation in asthmatics can be reduced effectively by treatment with fenoterol. A secondary finding of our study was that even after induction of anaesthesia with propofol, patients with a history of asthma may develop high Rrs.

Diagnosis of high-intensity pulsed heavy ion beam generated by a novel magnetically insulated diode with gas puff plasma gun.

PubMed

Ito, H; Miyake, H; Masugata, K

2008-10-01

Intense pulsed heavy ion beam is expected to be applied to materials processing including surface modification and ion implantation. For those applications, it is very important to generate high-purity ion beams with various ion species. For this purpose, we have developed a new type of a magnetically insulated ion diode with an active ion source of a gas puff plasma gun. When the ion diode was operated at a diode voltage of about 190 kV, a diode current of about 15 kA, and a pulse duration of about 100 ns, the ion beam with an ion current density of 54 A/cm(2) was obtained at 50 mm downstream from the anode. By evaluating the ion species and the energy spectrum of the ion beam via a Thomson parabola spectrometer, it was confirmed that the ion beam consists of nitrogen ions (N(+) and N(2+)) of energy of 100-400 keV and the proton impurities of energy of 90-200 keV. The purity of the beam was evaluated to be 94%. The high-purity pulsed nitrogen ion beam was successfully obtained by the developed ion diode system.

In-situ gamma-ray assay of the west cell line in the 235-F plutonium fuel form facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Couture, A. H.; Diprete, D.

On August 29th, 2013, scientists from SRNL took a series of in-situ gamma-ray measurements in the maintenance trench beneath Cells 6-9 on the west line of the PuFF facility using an uncollimated, highpurity germanium detector. The detector efficiency was estimated using a combination of MCNP simulations and empirical measurements. Data analysis was performed using three gamma-rays emitted by Pu-238 (99.85 keV, 152.7 keV, and 766.4 keV) providing three independent estimates of the mass of Pu-238 holdup in each of the cells. The weighted mean of these three results was used as the best estimate of Pu-238 holdup in the Westmore » Cell Line of PuFF. The results of the assay measurements are found in the table below along with the results from the scoping assay performed in 2006. All uncertainties in this table (as well as the rest of the report) are given as 1σ. The total holdup in the West Cell Line was 2.4 ± 0.7 grams. This result is 0.6 g higher than the previous estimate, a 0.4σ difference.« less

Smoking topography and abstinence in adult female smokers

PubMed Central

McClure, Erin A.; Saladin, Michael E.; Baker, Nathaniel L.; Carpenter, Matthew J.; Gray, Kevin M.

2013-01-01

Preliminary evidence, within both adults and adolescents, suggests that the intensity with which cigarettes are smoked (i.e. smoking topography) is predictive of success during a cessation attempt. These reports have also shown topography to be superior compared to other variables, such as cigarettes per day, in the prediction of abstinence. The possibility that gender may influence this predictive relationship has not been evaluated, but may be clinically useful in tailoring gender-specific interventions. Within the context of a clinical trial for smoking cessation among women, adult daily smokers completed a laboratory session that included a 1-hour ad-libitum smoking period in which measures of topography were collected (N=135). Participants were then randomized to active medication (nicotine patch vs. varenicline) and abstinence was monitored for 4 weeks. Among all smoking topography measures and all abstinence outcomes, a moderate association was found between longer puff duration and greater puff volume and continued smoking during the active 4-week treatment phase, but only within the nicotine patch group. Based on the weak topography-abstinence relationship among female smokers found in the current study, future studies should focus on explicit gender comparisons to examine if these associations are specific to or more robust in male smokers. PMID:24018226

Dual Use of Cigarettes, Little Cigars, Cigarillos, and Large Cigars: Smoking Topography and Toxicant Exposure.

PubMed

Pickworth, Wallace B; Rosenberry, Zachary R; O'Grady, Kevin E; Koszowski, Bartosz

2017-04-01

Smoking topography variables and toxicant exposure (plasma nicotine and exhaled CO) were examined in 3 groups of study participants that smoked both cigarettes and either filtered little cigars (Winchester), cigarillos (Black & Mild), or large cigars (Phillies Blunt). Laboratory ad lib smoking of the cigar products was collected with a smoking puff analyzer; plasma levels of nicotine and exhaled CO were collected before and after smoking. Although there were no statistically significant differences in demographic and cigarette smoking topography among the groups, there were significant differences in how the different cigar products were smoked. Plasma nicotine boost was similar after all products but exhaled CO was greater after the cigarillo and large cigar than the little cigar. Some of the differences were due to the differences in article size but other differences were apparent even after adjustment for the amount of tobacco burned or the mouth intake (puff volume). The topography findings of differences among products challenge the practice of grouping cigars as a single entity in surveys, regulatory decisions, and discussions of toxicant exposure. The results add to the discussion of distinctions among products in the scientific assessment of public health risk and regulatory decisions.

Measurement of an electronic cigarette aerosol size distribution during a puff

NASA Astrophysics Data System (ADS)

Belka, Miloslav; Lizal, Frantisek; Jedelsky, Jan; Jicha, Miroslav; Pospisil, Jiri

Electronic cigarettes (e-cigarettes) have become very popular recently because they are marketed as a healthier alternative to tobacco smoking and as a useful tool to smoking cessation. E-cigarettes use a heating element to create an aerosol from a solution usually consisting of propylene glycol, glycerol, and nicotine. Despite the wide spread of e-cigarettes, information about aerosol size distributions is rather sparse. This can be caused by the relative newness of e-cigarettes and by the difficulty of the measurements, in which one has to deal with high concentration aerosol containing volatile compounds. Therefore, we assembled an experimental setup for size measurements of e-cigarette aerosol in conjunction with a piston based machine in order to simulate a typical puff. A TSI scanning mobility particle sizer 3936 was employed to provide information about particle concentrations and sizes. An e-cigarette commercially available on the Czech Republic market was tested and the results were compared with a conventional tobacco cigarette. The particles emitted from the e-cigarette were smaller than those of the conventional cigarette having a CMD of 150 and 200 nm. However, the total concentration of particles from e-cigarette was higher.

Neutron Activation Diagnostics in Deuterium Gas-Puff Experiments on the 3 MA GIT-12 Z-Pinch

NASA Astrophysics Data System (ADS)

Cikhardt, J.; Klir, D.; Rezac, K.; Cikhardtova, B.; Kravarik, J.; Kubes, P.; Sila, O.; Shishlov, A. V.; Cherdizov, R. K.; Fursov, F. I.; Kokshenev, V. A.; Kurmaev, N. E.; Labetsky, A. Yu; Ratakhin, N. A.; Dudkin, G. N.; Garapatsky, A. A.; Padalko, V. N.; Varlachev, V. A.; Turek, K.

2016-10-01

The experiments with a deuterium z-pinch on the GIT-12 generator at IHCE in Tomsk were performed in the frame of the Czech-Russian agreement. A set of neutron diagnostics included scintillation time-of-flight detectors, bubble detectors, and several kinds of threshold nuclear activation detectors in the order to obtain information about the yield, anisotropy, and spectrum of the neutrons produced by a deuterium gas-puff. The average neutron yield in these experiments was of the order of 1012 neutrons per a single shot. The energy spectrum of the produced neutrons was evaluated using neutron time-of-flight detectors and a set of neutron activation detectors. Because the deuterons in the pinch achieve multi-MeV energies, non-DD neutrons are produced by nuclear reactions of deuterons with a stainless steel vacuum chamber and aluminum components of diagnostics inside the chamber. An estimated number of the non-DD was of the order of 1011. GACR (Grant No. 16-07036S), CME (Grant Nos. LD14089, LG13029, and LH13283), MESRF (Grant No. RFMEFI59114X0001), IAEA (Grant No. RC17088), CTU (Grant No. SGS 16/223/OHK3/3T/13).

Corneal Vibrations during Intraocular Pressure Measurement with an Air-Puff Method

PubMed Central

Wilczyński, Sławomir

2018-01-01

Introduction The paper presents a commentary on the method of analysis of corneal vibrations occurring during eye pressure measurements with air-puff tonometers, for example, Corvis. The presented definition and measurement method allow for the analysis of image sequences of eye responses—cornea deformation. In particular, the outer corneal contour and sclera fragments are analysed, and 3D reconstruction is performed. Methods On this basis, well-known parameters such as eyeball reaction or corneal response are determined. The next steps of analysis allow for automatic and reproducible separation of four different corneal vibrations. These vibrations are associated with (1) the location of the maximum of cornea deformation; (2) the cutoff area measured in relation to the cornea in a steady state; (3) the maximum of peaks occurring between applanations; and (4) the other characteristic points of the corneal contour. Results The results obtained enable (1) automatic determination of the amplitude of vibrations; (2) determination of the frequency of vibrations; and (3) determination of the correlation between the selected types of vibrations. Conclusions These are diagnostic features that can be directly applied clinically for new and archived data. PMID:29610655

A compact "water-window" microscope with 60-nm spatial resolution based on a double stream gas-puff target and Fresnel zone plate optics

NASA Astrophysics Data System (ADS)

Wachulak, Przemyslaw; Torrisi, Alfio; Nawaz, Muhammad F.; Adjei, Daniel; Bartnik, Andrzej; Kostecki, Jerzy; Wegrzynski, Łukasz; Vondrová, Šárka; Turňová, Jana; Fok, Tomasz; Jančarek, Alexandr; Fiedorowicz, Henryk

2015-05-01

Radiation with shorter illumination wavelength allows for extension of the diffraction limit towards nanometer scale, which is a straightforward way to significantly improve a spatial resolution in photon based microscopes. Soft X-ray (SXR) radiation, from the so called "water window" spectral range, λ=2.3-4.4 nm, which is particularly suitable for biological imaging due to natural optical contrast, providing much better spatial resolution than one obtained with visible light microscopes. The high contrast is obtained because of selective absorption of radiation by carbon and water, being constituents of the biological samples. We present a desk-top system, capable of resolving 60 nm features in few seconds exposure time. We exploit the advantages of a compact, laser-plasma SXR source, based on a double stream nitrogen gas puff target, developed at the Institute of Optoelectronics, Military University of Technology. The source, emitting quasi-monochromatic, incoherent radiation, in the "water widow" spectral range at λ = 2.88 nm, is coupled with ellipsoidal, grazing incidence condenser and Fresnel zone plate objective. The construction of the microscope with some recent images of test and real samples will be presented and discussed.

Characteristics of enriched cultures for bio-huff-`n`-puff tests at Jilin oil field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiu-Yuan Wang; Gang Dai; Yan-Fen Xue

1995-12-31

Three enriched cultures (48, 15a, and 26a), selected from more than 80 soil and water samples, could grow anaerobically in the presence of crude oil at 30{degrees}C and could ferment molasses to gases and organic acids. Oil recovery by culture 48 in the laboratory model experiment was enhanced by 25.2% over the original reserves and by 53.7% over the residual reserves. Enriched culture 48 was composed of at least 4 species belonging to the genera Eubacterium, Fusobacterium, and Bacteroides. This enriched culture was used as inoculum for MEOR field trials at Jilin oil field with satisfactory results. The importance ofmore » the role of these isolates in EOR was confirmed by their presence and behavior in the fluids produced from the microbiologically treated reservoir.« less

Landing of the Shuttle Discovery at the end of the STS 51-D mission

NASA Technical Reports Server (NTRS)

1985-01-01

A side looking, wide view of the Shuttle Discovery shows the vehicle on its final approach to the Kennedy Space Center (KSC) landing site (9107); Discovery's nose wheels touch down at the KSC landing site (9108); Discovery's main landing gear touches down, throwing puffs of dirt in the air. The orbiter's nose wheels are still in the air (9109).

Smoking Through a Topography Device Diminishes Some of the Acute Rewarding Effects of Smoking.

PubMed

Ross, Kathryn C; Juliano, Laura M

2016-05-01

Smoking topography (ST) devices are an important methodological tool for quantifying puffing behavior (eg, puff volume, puff velocity) as well as identifying puffing differences across individuals and situations. Available ST devices are designed such that the smoker's mouth and hands have direct contact with the device rather than the cigarette itself. Given the importance of the sensorimotor aspects of cigarette smoking in smoking reward, it is possible that ST devices may interfere with the acute rewarding effects of smoking. Despite the methodological importance of this issue, few studies have directly compared subjective reactions to smoking through a topography device to naturalistic smoking. Smokers (N = 58; 38% female) smoked their preferred brand of cigarettes one time through a portable topography device and one time naturalistically, in counterbalanced order across two laboratory sessions. Smoking behavior (eg, number of puffs) and subjective effects (eg, urge reduction, affect, smoking satisfaction) were assessed. Negative affect reduction was greater in the natural smoking condition relative to the topography condition, but differences were not significant on measures of urge, withdrawal, or positive affect. Self-reported smoking satisfaction, enjoyment of respiratory tract sensations, psychological reward, craving reduction, and other rewarding effects of smoking were also significantly greater in the naturalistic smoking condition. The effects of using a ST device on the smoking experience should be considered when it is used in research as it may diminish some of the rewarding effects of smoking. When considering the inclusion of a smoking topography device in one's research, it is important to know if use of that device will alter the smoker's experience. This study assessed affective and subjective reactions to smoking through a topography device compared to naturalistic smoking. We found that smoking satisfaction, psychological reward, enjoyment of respiratory tract sensations and other rewarding effects were all diminished when smoking through the topography device. The effects of using a smoking topography device on the smoking experience should be considered when it is used in future research. © The Author 2015. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Smoking Through a Topography Device Diminishes Some of the Acute Rewarding Effects of Smoking

PubMed Central

Juliano, Laura M.

2016-01-01

Abstract Background: Smoking topography (ST) devices are an important methodological tool for quantifying puffing behavior (eg, puff volume, puff velocity) as well as identifying puffing differences across individuals and situations. Available ST devices are designed such that the smoker’s mouth and hands have direct contact with the device rather than the cigarette itself. Given the importance of the sensorimotor aspects of cigarette smoking in smoking reward, it is possible that ST devices may interfere with the acute rewarding effects of smoking. Despite the methodological importance of this issue, few studies have directly compared subjective reactions to smoking through a topography device to naturalistic smoking. Methods: Smokers ( N = 58; 38% female) smoked their preferred brand of cigarettes one time through a portable topography device and one time naturalistically, in counterbalanced order across two laboratory sessions. Smoking behavior (eg, number of puffs) and subjective effects (eg, urge reduction, affect, smoking satisfaction) were assessed. Results: Negative affect reduction was greater in the natural smoking condition relative to the topography condition, but differences were not significant on measures of urge, withdrawal, or positive affect. Self-reported smoking satisfaction, enjoyment of respiratory tract sensations, psychological reward, craving reduction, and other rewarding effects of smoking were also significantly greater in the naturalistic smoking condition. Conclusions: The effects of using a ST device on the smoking experience should be considered when it is used in research as it may diminish some of the rewarding effects of smoking. Implications: When considering the inclusion of a smoking topography device in one’s research, it is important to know if use of that device will alter the smoker’s experience. This study assessed affective and subjective reactions to smoking through a topography device compared to naturalistic smoking. We found that smoking satisfaction, psychological reward, enjoyment of respiratory tract sensations and other rewarding effects were all diminished when smoking through the topography device. The effects of using a smoking topography device on the smoking experience should be considered when it is used in future research. PMID:26209851

Reduced Exposure to Harmful and Potentially Harmful Smoke Constituents With the Tobacco Heating System 2.1.

PubMed

Lüdicke, Frank; Baker, Gizelle; Magnette, John; Picavet, Patrick; Weitkunat, Rolf

2017-02-01

Heating rather than burning tobacco reduces levels of harmful and potentially harmful constituents, and consumer products using this approach aim to reduce exposure to tobacco toxicants. The Tobacco Heating System (THS) version 2.1 has been enhanced from earlier prototypes with an improved heat control and sensorial experience and thereby user acceptance. Exposure measurements are required to determine whether it may be possible to reduce the individual health risk compared to smoking combustible cigarettes (CCs). This controlled clinical study randomly assigned 40 smokers to either a group continuing to use of their own CC brand (n = 20) or a group switching to THS 2.1 (n = 20) for 5 days. Biomarkers of exposure were measured at baseline and on day 1 through day 5. Product consumption, Human Puffing Topography, the occurrence of adverse events, and an assessment of subjective effects, such as smoking satisfaction and enjoyment of respiratory tract sensations, were also determined. The group of smokers who switched to THS 2.1 adapted their puffing behavior initially through longer puff duration and more puffs. During the duration of the study, total puff volume returned to baseline levels and the mean daily product consumption increased but with similar nicotine exposure compared to baseline CC use. Biomarkers of exposure to tobacco smoke toxicants which inform product risk assessment were significantly reduced with THS use compared to the CC group. THS 2.1 users experienced less reinforcing effects with THS 2.1 than with their own cigarette brand. THS 2.1 is a promising alternative to smoking CCs. Notwithstanding possible use adaption through consumption or puffing behavior, the exposure to harmful smoke constituents was markedly reduced with the new heated tobacco platform. Exposure markers to harmful and potentially harmful smoke constituents were lowered with the THS 2.1. Heating tobacco instead of burning can offer a potentially lower risk of delivering nicotine compared to CCs. © The Author 2016. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco.

Response to Albuterol MDI Delivered Through an Anti-Static Chamber During Nocturnal Bronchospasm

PubMed Central

Prabhakaran, Sreekala; Shuster, Jonathan; Chesrown, Sarah; Hendeles, Leslie

2013-01-01

BACKGROUND Decreasing electrostatic charge on valved holding chambers increases the amount of drug delivered. However, there are no data demonstrating that this increases bronchodilatation. OBJECTIVE To investigate the influence of reducing electrostatic charge on the bronchodilator response to albuterol inhaler during nocturnal bronchospasm. METHODS This randomized double-blind, double-dummy crossover study included subjects, 18—40 years old, with nocturnal bronchospasm (20% overnight decrease in peak flow on 3 of 7 nights during run-in), FEV1 60–80% predicted during the day, and ≥ 12% increase after albuterol. Subjects slept in the clinical research center up to 3 nights for each treatment. FEV1 and heart rate were measured upon awakening spontaneously or at 4:00 am, and 15 min after each dose of 1, 2, and 4 cumulative puffs of albuterol via metered-dose inhaler. The drug was administered through an anti-static valved holding chamber (AeroChamber Plus Z-Stat) or a conventional valved holding chamber containing a static charge (AeroChamber Plus). RESULTS Of 88 consented subjects, 11 were randomized and 7 completed the study. Most exclusions were due to lack of objective evidence of nocturnal bronchospasm. Upon awakening, FEV1 was 44 ± 9% of predicted before the anti-static chamber and 48 ± 7% of predicted before the static chamber. The mean ± SD percent increase in FEV1 after 1, 2, and 4 cumulative puffs using the anti-static versus the static chamber, respectively, were 52 ± 26% versus 30 ± 19%, 73 ± 28% versus 48 ± 26%, and 90 ± 34% versus 64 ± 35%. The point estimates for the differences (and 95% CIs) between the devices (anti-static vs static) were 21% (4–38%) (P = .03), 23% (6–41%) (P = .02), and 25% (7–42%) (P = .01) for 1, 2, and 4 cumulative puffs, respectively. There was no significant difference in heart rate between treatments. CONCLUSIONS Delivery of albuterol through an anti-static chamber provides a clinically relevant improvement in bronchodilator response during acute, reversible bronchospasm such as nocturnal bronchospasm. PMID:22348270

E-cigarettes: Impact of E-Liquid Components and Device Characteristics on Nicotine Exposure.

PubMed

DeVito, Elise E; Krishnan-Sarin, Suchitra

2018-01-01

Electronic cigarette (e-cigarette) use has increased substantially in recent years. While e-cigarettes have been proposed as a potentially effective smoking cessation tool, dualuse in smokers is common and e-cigarettes are widely used by non-smokers, including youth and young-adult non-smokers. Nicotine, the primary addictive component in cigarettes, is present at varying levels in many e-liquids. E-cigarettes may lead to initiation of nicotine use in adult and youth non-smokers, re-initiation of nicotine dependence in ex-smokers or increased severity of nicotine dependence in dual-users of cigarettes and e-cigarettes. As such, there are important clinical and policy implications to understanding factors impacting nicotine exposure from e-cigarettes. However, the broad and rapidly changing range of e-liquid constituents and e-cigarette hardware which could impact nicotine exposure presents a challenge. Recent changes in regulatory oversight of e-cigarettes underscore the importance of synthesizing current knowledge on common factors which may impact nicotine exposure. This review focuses on factors which may impact nicotine exposure by changing e-cigarette use behavior, puff topography, altering the nicotine yield (amount of nicotine exiting the e-cigarette mouth piece including nicotine exhaled as vapor) or more directly by altering nicotine absorption and bioavailability. Topics reviewed include e-liquid components or characteristics including flavor additives (e.g., menthol), base e-liquid ingredients (propylene glycol, vegetable glycerin), components commonly used to dissolve flavorants (e.g., ethanol), and resulting properties of the e-liquid (e.g., pH), e-cigarette device characteristics (e.g., wattage, temperature, model) and user behavior (e.g., puff topography) which may impact nicotine exposure. E-liquid characteristics and components, e-cigarette hardware and settings, and user behavior can all contribute substantially to nicotine exposure from e-cigarettes. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Indacaterol vs tiotropium in COPD patients classified as GOLD A and B.

PubMed

Mahler, Donald A; Kerstjens, Huib A M; Donohue, James F; Buhl, Roland; Lawrence, David; Altman, Pablo

2015-08-01

According to current GOLD strategy, patients with COPD classified as groups A and B may be treated with inhaled bronchodilators, either long-acting β2-agonist (LABA) or long-acting muscarinic antagonist (LAMA). However, there is little guidance on which class of agent is preferred and a lack of prospective data to differentiate the two. In this study, we performed post-hoc analyses of pooled data from two prospective, controlled clinical trials comparing the LABA indacaterol and LAMA tiotropium in 1422 patients with moderate airflow limitation and no history of exacerbations in the previous year. This population fits the definitions of GOLD A and B groups and could be further stratified by symptom severity using Baseline Dyspnea Index (i.e. modeling GOLD A or B) and inhaled corticosteroid (ICS) use at baseline. Outcomes measured after 12 weeks of treatment were lung function (forced expiratory volume in 1 s; FEV1), health status (St George's Respiratory Questionnaire; SGRQ), symptoms (Transition Dyspnea Index; TDI) and rescue medication use. In 'GOLD A' patients not receiving ICS, differences favored indacaterol versus tiotropium (trough FEV1 0.05 L; rescue medication use -0.41 puffs/day; TDI total score 0.94 points; SGRQ total score -3.13 units, all p < 0.01). In 'GOLD B, no ICS' patients, compared with tiotropium, indacaterol treatment increased trough FEV1 (0.055 L, p < 0.05) and permitted a larger reduction in rescue medication use (-0.81 puffs/day, p = 0.004). In all patients, and in patients not using ICS, differences favored indacaterol for all variables. Our findings suggest that patients in GOLD groups A and B may experience greater benefits with indacaterol than with tiotropium. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Introduction of Two Novel Stiffness Parameters and Interpretation of Air Puff-Induced Biomechanical Deformation Parameters With a Dynamic Scheimpflug Analyzer.

PubMed

Roberts, Cynthia J; Mahmoud, Ashraf M; Bons, Jeffrey P; Hossain, Arif; Elsheikh, Ahmed; Vinciguerra, Riccardo; Vinciguerra, Paolo; Ambrósio, Renato

2017-04-01

To investigate two new stiffness parameters and their relationships with the dynamic corneal response (DCR) parameters and compare normal and keratoconic eyes. Stiffness parameters are defined as Resultant Pressure at inward applanation (A1) divided by corneal displacement. Stiffness parameter A1 uses displacement between the undeformed cornea and A1 and stiffness parameter highest concavity (HC) uses displacement from A1 to maximum deflection during HC. The spatial and temporal profiles of the Corvis ST (Oculus Optikgeräte, Wetzlar, Germany) air puff were characterized using hot wire anemometry. An adjusted air pressure impinging on the cornea at A1 (adjAP1) and an algorithm to biomechanically correct intraocular pressure based on finite element modelling (bIOP) were used for Resultant Pressure calculation (adjAP1 - bIOP). Linear regression analyses between DCR parameters and stiffness parameters were performed on a retrospective dataset of 180 keratoconic eyes and 482 normal eyes. DCR parameters from a subset of 158 eyes of 158 patients in each group were matched for bIOP and compared using t tests. A P value of less than .05 was considered statistically significant. All DCR parameters evaluated showed significant differences between normal and keratoconic eyes, except peak distance. Keratoconic eyes had lower stiffness parameter values, thinner pachymetry, shorter applanation lengths, greater absolute values of applanation velocities, earlier A1 times and later second applanation times, greater HC deformation amplitudes and HC deflection amplitudes, and lower HC radius of concave curvature (greater concave curvature). Most DCR parameters showed a significant relationship with both stiffness parameters in both groups. Keratoconic eyes demonstrated less resistance to deformation than normal eyes with similar IOP. The stiffness parameters may be useful in future biomechanical studies as potential biomarkers. [J Refract Surg. 2017;33(4):266-273.]. Copyright 2017, SLACK Incorporated.

Optical remote sensing to quantify fugitive particulate mass emissions from stationary short-term and mobile continuous sources: part II. Field applications.

PubMed

Du, Ke; Yuen, Wangki; Wang, Wei; Rood, Mark J; Varma, Ravi M; Hashmonay, Ram A; Kim, Byung J; Kemme, Michael R

2011-01-15

Quantification of emissions of fugitive particulate matter (PM) into the atmosphere from military training operations is of interest by the United States Department of Defense. A new range-resolved optical remote sensing (ORS) method was developed to quantify fugitive PM emissions from puff sources (i.e., artillery back blasts), ground-level mobile sources (i.e., movement of tracked vehicles), and elevated mobile sources (i.e., airborne helicopters) in desert areas that are prone to generating fugitive dust plumes. Real-time, in situ mass concentration profiles for PM mass with particle diameters <10 μm (PM(10)) and <2.5 μm (PM(2.5)) were obtained across the dust plumes that were generated by these activities with this new method. Back blasts caused during artillery firing were characterized as a stationary short-term puff source whose plumes typically dispersed to <10 m above the ground with durations of 10-30 s. Fugitive PM emissions caused by artillery back blasts were related to the zone charge and ranged from 51 to 463 g PM/firing for PM(10) and 9 to 176 g PM/firing for PM(2.5). Movement of tracked vehicles and flying helicopters was characterized as mobile continuous sources whose plumes typically dispersed 30-50 m above the ground with durations of 100-200 s. Fugitive PM emissions caused by moving tracked vehicles ranged from 8.3 to 72.5 kg PM/km for PM(10) and 1.1 to 17.2 kg PM/km for PM(2.5), and there was no obvious correlation between PM emission and vehicle speed. The emission factor for the helicopter flying at 3 m above the ground ranged from 14.5 to 114.1 kg PM/km for PM(10) and 5.0 to 39.5 kg PM/km for PM(2.5), depending on the velocity of the helicopter and type of soil it flies over. Fugitive PM emissions by an airborne helicopter were correlated with helicopter speed for a particular soil type. The results from this range-resolved ORS method were also compared with the data obtained with another path-integrated ORS method and a Flux Tower method.

Feeding Concept, Military Vs Civilian System

DTIC Science & Technology

1990-12-01

Pudding d 3 c Chocolate Pudding w/Whipped Topping d 3 c Cowboy Cookies d 3 c Cream Puffs d 3 c Donuts d...c Fruit Won Tons d 3 c Gelatin Cubes d 3 c Hermits d 3 c Ice Box Cookies d : c Ice Cream d...I c Jelly Bar Spritz d 3 c Jelly Roll d : c Lemon Meringue Pie d : c Lime Gelatin Cubes d : c Oatmeal Cookies

Phlebotomus Sandflies of the Paloich Area in the Sudan (Diptera, Psychodidae)

DTIC Science & Technology

1964-10-01

Hamster, Cricetus auratus Toad, Bufo regularis (?) Gecko, H. turicus Skink, M. striata Puff adder Snake, CMNH HH-9111’ Snake, CMNH HH-9112’ Hedgehog ...Pharynx unarmed distally or only with few, smail spines ; pigment patch not dark enough to obscure teeth .................. 8 Pharynx heavily...armed distally with numerous, dark spines ; pigment patch very dark, 1964 Quate: Sudanese sandflies 237 often obscuring teeth unless specimen well

Smoking Behavior and Exposure: Results of a Menthol Cigarette Cross-over Study.

PubMed

Watson, Christina Vaughan; Richter, Patricia; de Castro, B Rey; Sosnoff, Connie; Potts, Jennifer; Clark, Pamela; McCraw, Joan; Yan, Xizheng; Chambers, David; Watson, Clifford

2017-05-01

Our objective was to improve understanding of the differences in use behavior and exposure when smoking menthol and non-menthol cigarettes using a 2-part cross-over design. Adult daily smokers were assigned randomly to alternate between 2 weeks of exclusively smoking a menthol test cigarette or a non-menthol test cigarette. Urine and saliva were collected for biomarker measurements; carbon monoxide (CO) was measured, and participants smoked test cigarettes through a CreSS® smoking topography device during 3 clinic visits. Participants turned in their cigarette butts from the test periods for determination of mouth level nicotine and completed subjective questionnaires related to the test cigarettes. Regardless of cigarette preference, participants had higher salivary cotinine when smoking the non-menthol test cigarette, but there were no significant differences detected in urine 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol between the 2 test cigarettes. Mouth level nicotine, puff volume, and puff duration were significantly higher when smoking the menthol brand. Both menthol and non-menthol smokers reported significantly lower enjoyment and satisfaction scores for test cigarettes compared with their brand of choice. Our results suggest that mentholation has an effect on measures of smoking behavior and that mouth level nicotine is a useful indicator of between-brand smoke exposure.

Study of the confinement properties in a reversed-field pinch with mode rotation and gas fuelling

NASA Astrophysics Data System (ADS)

Cecconello, M.; Malmberg, J.-A.; Nielsen, P.; Pasqualotto, R.; Drake, J. R.

2002-08-01

An extensive investigation of the global confinement properties in different operating scenarios in the rebuilt EXTRAP T2R reversed-field pinch (RFP) experiment is reported here. In particular, the role of a fast gas puff valve system, used to control plasma density, on confinement is studied. Without gas puffing, the electron density decays below 0.5×1019 m-3. The poloidal beta varies between 5% and 15%, decreasing at large I/N. The energy confinement time ranges from 70 to 225 μs. With gas puffing, the density is sustained at ne≈1.5×1019 m-3. However, a general slight deterioration of the plasma performances is observed for the same values of I/N: the plasma becomes cooler and more radiative. The poloidal beta is comparable to that in the scenarios without puff but the energy confinement time drops ranging from 60 to 130 μs. The fluctuation level and the energy confinement time have been found to scale with the Lundquist number as S-0.05+/-0.07 and S0.5+/-0.1, respectively. Mode rotation is typical for all the discharges and rotation velocity is observed to increase with increasing electron diamagnetic velocity.

The linear relationship between cigarette tar and nicotine yields: regulatory implications for smoke constituent ratios.

PubMed

St Charles, F K; Cook, C J; Clayton, P M

2011-02-01

Cigarette smoke analyte yields are often expressed as ratios relative to tar or nicotine yields, usually to compare different products or to estimate human uptake of smoke in relation to nicotine uptake measurements. The method, however, can lead to distorted interpretations, especially in the case of ratios from ultra-low tar yield cigarettes. In brief, as tar yields decrease below the 5–6 mg per cigarette range, the tar-to-nicotine ratio (TNR) decreases rapidly in a non-linear fashion. If, however, the nicotine yield, rather than the ratio, is plotted versus the tar yield, the non-linearity disappears and a straight line is obtained, with a slight positive intercept for nicotine on the ordinate. Unlike the ratio, the slope appears to depend only on the concentration of the nicotine in the blend and does not appear to vary with smoking parameters such as puff volume, puff interval or length smoked or with cigarette design parameters such as length, circumference or the amount of filtration or filter ventilation. Therefore, such a slope is analogous to the TNR although, unlike that ratio, it is invariant. Even more simply, the concentration of the nicotine in the blend, at least for American blend-style cigarettes, provides a similar index.

Shock formation in Ne, Ar, Kr, and Xe on deuterium gas puff implosions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Narkis, J.; Rahman, H. U.; Ney, P.

2016-12-29

1- and 2-D simulations of 1-cm radius, gas-puff liners of Ne, Ar, Kr, and Xe imploding onto a deuterium target are conducted using the discharge parameters for the Zebra (1 MA, 130 ns) driver using the resistive MHD code MACH2. This is an implementation of the Staged Z-pinch concept, in which the target is driven to high-energy-density first by shock compression launched by a diffused azimuthal magnetic field (J×B force), and then by the adiabatic compression as the liner converges on axis. During the run-in phase, the initial shock heating preheats the deuterium plasma, with a subsequent stable, adiabatic compressionmore » heating the target to high energy density. Shock compression of the target coincides with the development of a J×B force at the target/liner interface. Stronger B-field transport and earlier shock compression increases with higher-Z liners, which results in an earlier shock arrival on axis. As a result, delayed shock formation in lower-Z liners yields a relative increase in shock heating, however, the 2-D simulations show an increased target isolation from magneto-Rayleigh-Taylor instability penetration, suggesting that an optimal balance between these two effects is reached in an Ar or Kr liner, rather than with Xe.« less

Dual Use of Cigarettes, Little Cigars, Cigarillos, and Large Cigars: Smoking Topography and Toxicant Exposure

PubMed Central

Pickworth, Wallace B.; Rosenberry, Zachary R.; O’Grady, Kevin E.; Koszowski, Bartosz

2017-01-01

Objective Smoking topography variables and toxicant exposure (plasma nicotine and exhaled CO) were examined in 3 groups of study participants that smoked both cigarettes and either filtered little cigars (Winchester), cigarillos (Black & Mild), or large cigars (Phillies Blunt). Methods Laboratory ad lib smoking of the cigar products was collected with a smoking puff analyzer; plasma levels of nicotine and exhaled CO were collected before and after smoking. Results Although there were no statistically significant differences in demographic and cigarette smoking topography among the groups, there were significant differences in how the different cigar products were smoked. Plasma nicotine boost was similar after all products but exhaled CO was greater after the cigarillo and large cigar than the little cigar. Some of the differences were due to the differences in article size but other differences were apparent even after adjustment for the amount of tobacco burned or the mouth intake (puff volume). Conclusions The topography findings of differences among products challenge the practice of grouping cigars as a single entity in surveys, regulatory decisions, and discussions of toxicant exposure. The results add to the discussion of distinctions among products in the scientific assessment of public health risk and regulatory decisions. PMID:28966952

Smoking topography and abstinence in adult female smokers.

PubMed

McClure, Erin A; Saladin, Michael E; Baker, Nathaniel L; Carpenter, Matthew J; Gray, Kevin M

2013-12-01

Preliminary evidence, within both adults and adolescents, suggests that the intensity with which cigarettes are smoked (i.e., smoking topography) is predictive of success during a cessation attempt. These reports have also shown topography to be superior compared to other variables, such as cigarettes per day, in the prediction of abstinence. The possibility that gender may influence this predictive relationship has not been evaluated but may be clinically useful in tailoring gender-specific interventions. Within the context of a clinical trial for smoking cessation among women, adult daily smokers completed a laboratory session that included a 1-hour ad libitum smoking period in which measures of topography were collected (N=135). Participants were then randomized to active medication (nicotine patch vs. varenicline) and abstinence was monitored for 4weeks. Among all smoking topography measures and all abstinence outcomes, a moderate association was found between longer puff duration and greater puff volume and continued smoking during the active 4-week treatment phase, but only within the nicotine patch group. Based on the weak topography-abstinence relationship among female smokers found in the current study, future studies should focus on explicit gender comparisons to examine if these associations are specific to or more robust in male smokers. © 2013 Elsevier Ltd. All rights reserved.

Genetic and Molecular Analysis of the X Chromosomal Region 14b17-14c4 in Drosophila Melanogaster: Loss of Function in Nona, a Nuclear Protein Common to Many Cell Types, Results in Specific Physiological and Behavioral Defects

PubMed Central

Stanewsky, R.; Rendahl, K. G.; Dill, M.; Saumweber, H.

1993-01-01

We have performed a genetic analysis of the 14C region of the X chromosome of Drosophila melanogaster to isolate loss of function alleles of no-on-transient A (nonA; 14C1-2; 1-52.3). NONA is a nuclear protein common to many cell types, which is present in many puffs on polytene chromosomes. Sequence data suggest that the protein contains a pair of RNA binding motifs (RRM) found in many single-strand nucleic acid binding proteins. Hypomorphic alleles of this gene, which lead to aberrant visual and courtship song behavior, still contain normally distributed nonA RNA and NONA protein in embryos, and in all available alleles NONA protein is present in puffs of third instar larval polytene chromosomes. We find that complete loss of this general nuclear protein is semilethal in hemizygous males and homozygous cell lethal in the female germline. Surviving males show more extreme defects in nervous system function than have been described for the hypomorphic alleles. Five other essential genes that reside within this region have been partially characterized. PMID:8244005

Diagnostics of deuterium gas-puff z-pinch experiments on the GIT-12 generator

NASA Astrophysics Data System (ADS)

Cikhardt, J.; Klir, D.; Rezac, K.; Kubes, P.; Kravarik, J.; Batobolotova, B.; Sila, O.; Turek, K.; Shishlov, A.; Labetsky, A.; Kokshenev, V.; Chedizov, R.; Ratakhin, N.; Varlachev, V.; Garapatsky, A.; Dudkin, G.; Padalko, V.; GIT-12 Team

2014-10-01

Z-pinch experiments with a deuterium gas-puff and an outer plasma shell generated by plasma guns were carried out on the GIT-12 generator at the IHCE in Tomsk. Using this novel configuration of the load, the neutron yields from the DD reaction were significantly increased from 2×1011 up to 3×1012 neutrons per shot at the current level of about 3 MA. In addition to recent experiments, the threshold activation detectors were used in order to get the information about the energy spectrum of the generated neutrons. The copper, indium, and lead samples were irradiated by the pulse of the neutrons generated during the experimental shot. The decay radiation of the products from the reactions 63Cu(n,2n)62Cu, 115In(n, γ) 116 mIn and 206Pb (n,3n)204mPb was observed using gamma spectrometer. According to the used neutron ToF scintillation detectors, the energy of neutrons reaches up to 20 MeV. The work was supported by the MSMT of the Czech Republic research Programs No. ME090871, No. LG13029, by the GACR Grant No. P205/12/0454, Grant CRA IAEA No. 17088 and RFBR research Project No. 13-08-00479-a.

Particle transport characteristics of the RT-1 magnetospheric plasma using gas-puffing modulation technique

NASA Astrophysics Data System (ADS)

Kenmochi, Naoki; Nishiura, Masaki; Yoshida, Zensho; Sugata, Tetsuya; Nakamura, Kaori; Katsura, Shotaro

2017-10-01

The Ring Trap 1 (RT-1) device creates a laboratory magnetosphere that is realized by a levitated superconducting ring magnet in vacuum. The RT-1 experiment has demonstrated the self-organization of a plasma clump with a steep density gradient; a peaked density distribution is spontaneously created through `inward diffusion'. In order to evaluate particle transport characteristics in the RT-1 magnetospheric plasmas which cause these inward diffusion, density modulation experiments were performed in the RT-1. Density modulation is a powerful method for estimating a diffusion coefficient D and a convection velocity V by puffing a periodic neutral gas. The gas puff modulation causes the change in the electron density measured by two chords of microwave interferometer (the radial positions r = 60 and 70 cm, vertical chord). In the case of 2 Hz gas puff modulation, the phase delay and the modulation-amplitude decay at the chord r = 60 cm are obtained with 15 degree and 0.8, respectively, with respect to the phase and the amplitude at r = 70 cm. The particle balance equations are solved on the assumption of profile shapes for D to evaluate D, V and particle source rate. The result suggests the inward convection in high beta magnetospheric plasmas.

Three predictions of the economic concept of unit price in a choice context.

PubMed

Madden, G J; Bickel, W K; Jacobs, E A

2000-01-01

Economic theory makes three predictions about consumption and response output in a choice situation: (a) When plotted on logarithmic coordinates, total consumption (i.e., summed across concurrent sources of reinforcement) should be a positively decelerating function, and total response output should be a bitonic function of unit price increases; (b) total consumption and response output should be determined by the value of the unit price ratio, independent of its cost and benefit components; and (c) when a reinforcer is available at the same unit price across all sources of reinforcement, consumption should be equal between these sources. These predictions were assessed in human cigarette smokers who earned cigarette puffs in a two-choice situation at a range of unit prices. In some sessions, smokers chose between different amounts of puffs, both available at identical unit prices. Individual subjects' data supported the first two predictions but failed to support the third. Instead, at low unit prices, the relatively larger reinforcer (and larger response requirement) was preferred, whereas at high unit prices, the smaller reinforcer (and smaller response requirement) was preferred. An expansion of unit price is proposed in which handling costs and the discounted value of reinforcers available according to ratio schedules are incorporated.

Initial Development of an E-cigarette Purchase Task: A Mixed Methods Study

PubMed Central

Cassidy, Rachel N.; Tidey, Jennifer W.; Colby, Suzanne M.; Long, Victoria; Higgins, Stephen T.

2017-01-01

Objectives Behavioral economic purchase tasks, which estimate demand for drugs, have been successfully developed for cigarettes and are widely used. However, a validated purchase task does not yet exist for e-cigarettes. The aim of this project was to identify the relevant units for an e-cigarette purchase task (E-CPT). Methods Focus groups (N=28 participants in 7 groups, 2-7 participants per group) consisting of current e-cigarette users were conducted. Participants discussed their daily use patterns, completed a preliminary E-CPT which asked how many puffs of their e-cigarette they would consume per day at escalating prices, and discussed the extent to which the task accurately reflected their real-world behavior. Groups were recorded and transcribed; analysis focused on statements related to daily consumption and the E-CPT. Results Participants were unlikely to quantify their daily use in terms of puffs, and perceptions about the appropriate unit for an E-CPT varied across device type. Users of first-generation devices (eg, cigalikes) reported that the relevant unit was the individual device/cartridge; however, participants who purchased nicotine liquid for their device emphasized that e-liquid volume in milliliters would better reflect their use. Conclusions Multiple versions of the E-CPT may be necessary to provide valid measures of e-cigarette demand. PMID:28824938

Quad quantum cascade laser spectrometer with dual gas cells for the simultaneous analysis of mainstream and sidestream cigarette smoke

NASA Astrophysics Data System (ADS)

Baren, Randall E.; Parrish, Milton E.; Shafer, Kenneth H.; Harward, Charles N.; Shi, Quan; Nelson, David D.; McManus, J. Barry; Zahniser, Mark S.

2004-12-01

A compact, fast response, infrared spectrometer using four pulsed quantum cascade (QC) lasers has been applied to the analysis of gases in mainstream (MS) and sidestream (SS) cigarette smoke. QC lasers have many advantages over the traditional lead-salt tunable diode lasers, including near room temperature operation with thermoelectric cooling and single mode operation with improved long-term stability. The new instrument uses two 36 m, 0.3 l multiple pass absorption gas cells to obtain a time response of 0.1 s for the MS smoke system and 0.4 s for the SS smoke system. The concentrations of ammonia, ethylene, nitric oxide, and carbon dioxide for three different reference cigarettes were measured simultaneously in MS and SS smoke. A data rate of 20 Hz provides sufficient resolution to determine the concentration profiles during each 2 s puff in the MS smoke. Concentration profiles before, during and after the puffs also have been observed for these smoke constituents in SS smoke. Also, simultaneous measurements of CO 2 from a non-dispersive infrared (NDIR) analyzer are obtained for both MS and SS smoke. In addition, during this work, nitrous oxide was detected in both the MS and SS smoke for all reference cigarettes studied.

Analysis of co-crystallized free phytosterols with triacylglycerols as a functional food ingredient.

PubMed

Acevedo, Nuria C; Franchetti, Danielle

2016-07-01

This research focuses on the analysis of mixtures of free phytosterols (FPSs) with fully hydrogenated soybean oil (FHSO):soybean oil (SO) mixtures as a potential zero-trans substitute for various types of shortenings. Oil binding capacity as well as the thermal, rheological and structural properties of FHSO:SO blends containing 0, 20 and 25wt.% β-sitosterol or stigmasterol were investigated in this study. Differential interference contrast (DIC) microscopy and wide angle X-ray diffraction (WAXRD) revealed that co-crystallization of FPSs with FHSO:SO blends occurred. Polymorphic forms were characterized as a mixture of β' and β for all samples. The addition of FPSs decreased oil loss (OL) of FHSO:SO samples. Melting profiles of the prepared FPS-TAG (triacylglycerol) blends were extended to higher temperatures compared to a commercial shortening. Rheological properties were comparable to those of commercial puff pastry shortening suggesting that FPS-TAG blends may be acceptable for bakery applications. FPSs co-crystallized with FHSO and SO may be a suitable trans-fat free substitute for a number of types of shortening, including puff pastry shortening. The manufacturing of co-crystallized /FPS-TAG matrices will possibly bring large economic benefits as their functionalization can potentially be achieved by using existing simple shear processing. Copyright © 2016 Elsevier Ltd. All rights reserved.

Smoking Behavior and Exposure: Results of a Menthol Cigarette Crossover Study

PubMed Central

Watson, Christina; Richter, Patricia; de Castro, B. Rey; Sosnoff, Connie; Potts, Jennifer; Clark, Pamela; McCraw, Joan; Yan, Xizheng; Chambers, David; Watson, Cliff

2017-01-01

Objective Our objective was to better understand differences in use behavior and exposure when smoking menthol and nonmenthol cigarettes using a 2-part cross-over design. Methods Adult daily smokers were randomly assigned to alternate between 2 weeks of exclusively smoking a menthol test cigarette or a nonmenthol test cigarette. Urine and saliva were collected for biomarker measurements, carbon monoxide (CO) was measured, and participants smoked test cigarettes through a CreSS® smoking topography device during 3 clinic visits. Participants turned in their cigarette butts from the test periods for determination of mouth level nicotine and completed subjective questionnaires related to the test cigarettes. Results Regardless of cigarette preference, participants had higher salivary cotinine when smoking the nonmenthol test cigarette, but there were no significant differences detected in urine 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol between the 2 test cigarettes. Mouth level nicotine, puff volume and puff duration were significantly higher when smoking the menthol brand. Both menthol and nonmenthol smokers reported significantly lower enjoyment and satisfaction scores for test cigarettes compared with their brand of choice. Conclusions Our results suggest that mentholation has an effect on measures of smoking behavior and that mouth level nicotine is a useful indicator of between-brand smoke exposure. PMID:28376975

Flavoring Chemicals and Aldehydes in E-Cigarette Emissions.

PubMed

Klager, Skylar; Vallarino, Jose; MacNaughton, Piers; Christiani, David C; Lu, Quan; Allen, Joseph G

2017-09-19

Regulations on e-cigarettes in the U.S. do not provide guidelines on the chemical content of e-cigarette liquids. We evaluated emissions of aldehydes and flavoring chemicals in e-cigarette vapor under typical usage conditions. We selected 24 e-cigarette flavors from the top selling disposable e-cigarette brands. E-cigarettes were connected to a pump drawing air for two second puffs with sixty-second intervals between puffs. The vapor was analyzed for the presence of aldehydes using high-performance liquid chromatography-ultraviolet detector and for the presence of flavoring chemicals with gas chromatography and an electron capture detector. All e-cigarette emissions tested contained at least one aldehyde and/or flavoring chemical on either the FEMA "High Priority Chemicals" or FDA Harmful and Potentially Harmful Constituents lists when sampled at typical usage conditions. Diacetyl, a known respiratory hazard, along with acetoin, were the most prevalent of the flavoring chemicals in e-cigarette vapor, being found in more than 60% of samples. The presence of propionaldehyde, acetaldehyde and formaldehyde were correlated, corroborating previous work suggesting thermal degradation as a pathway for aldehyde generation in e-cigarette vapors. Median formaldehyde concentrations of 626 μg/m 3 in e-cigarette vapor exceed the ACGIH maximum concentrations allowable for workers of 370 μg/m 3 .

Volcanic ash plume identification using polarization lidar: Augustine eruption, Alaska

USGS Publications Warehouse

Sassen, Kenneth; Zhu, Jiang; Webley, Peter W.; Dean, K.; Cobb, Patrick

2007-01-01

During mid January to early February 2006, a series of explosive eruptions occurred at the Augustine volcanic island off the southern coast of Alaska. By early February a plume of volcanic ash was transported northward into the interior of Alaska. Satellite imagery and Puff volcanic ash transport model predictions confirm that the aerosol plume passed over a polarization lidar (0.694 mm wavelength) site at the Arctic Facility for Atmospheric Remote Sensing at the University of Alaska Fairbanks. For the first time, lidar linear depolarization ratios of 0.10 – 0.15 were measured in a fresh tropospheric volcanic plume, demonstrating that the nonspherical glass and mineral particles typical of volcanic eruptions generate strong laser depolarization. Thus, polarization lidars can identify the volcanic ash plumes that pose a threat to jet air traffic from the ground, aircraft, or potentially from Earth orbit.

Phase transition to turbulence in a pipe

NASA Astrophysics Data System (ADS)

Goldenfeld, Nigel

Leo Kadanoff taught us much about phase transitions, turbulence and collective behavior. Here I explore the transition to turbulence in a pipe, showing how a collective mode determines the universality class. Near the transition, turbulent puffs decay either directly or through splitting, with characteristic time-scales that exhibit a super-exponential dependence on Reynolds number. Direct numerical simulations reveal that a collective mode, a so-called zonal flow emerges at large scales, activated by anisotropic turbulent fluctuations, as represented by Reynolds stress. This zonal flow imposes a shear on the turbulent fluctuations that tends to suppress their anisotropy, leading to a Landau theory of predator-prey type, in the directed percolation universality class. Stochastic simulations of this model reproduce the functional form and phenomenology of pipe flow experiments. Talk based on work performed with Hong-Yan Shih and Tsung-Lin Hsieh. This work was partially supported by the National Science Foundation through Grant NSF-DMR-1044901.

Verification of conventional equations of state for tantalum under quasi-isentropic compression

DOE Office of Scientific and Technical Information (OSTI.GOV)

Binqiang, Luo; Guiji, Wang; Jianjun, Mo

2014-11-21

Shock Hugoniot data have been widely used to calibrate analytic equations of state (EOSs) of condensed matter at high pressures. However, the suitability of particular analytic EOSs under off-Hugoniot states has not been sufficiently verified using experimental data. We have conducted quasi-isentropic compression experiments (ICEs) of tantalum using the compact pulsed power generator CQ-4, and explored the relation of longitudinal stress versus volume of tantalum under quasi-isentropic compression using backward integration and characteristic inverse methods. By subtracting the deviatoric stress and additional pressure caused by irreversible plastic dissipation, the isentropic pressure can be extracted from the longitudinal stress. Several theoreticalmore » isentropes are deduced from analytic EOSs and compared with ICE results to validate the suitability of these analytic EOSs in isentropic compression states. The comparisons show that the Gruneisen EOS with Gruneisen Gamma proportional to volume is accurate, regardless whether the Hugoniot or isentrope is used as the reference line. The Vinet EOS yields better accuracy in isentropic compression states. Theoretical isentropes derived from Tillotson, PUFF, and Birch-Murnaghan EOSs well agree with the experimental isentrope in the range of 0–100 GPa, but deviate gradually with pressure increasing further.« less

Ingredient Functionality in Multilayered Dough-margarine Systems and the Resultant Pastry Products: A Review.

PubMed

Ooms, Nand; Pareyt, Bram; Brijs, Kristof; Delcour, Jan A

2016-10-02

Pastry products are produced from heterogeneous multilayered dough systems. The main ingredients are flour, water, fat and sugar for puff pastry, and the same plus yeast for fermented pastry. Key aspects in pastry production are (i) building laminated dough containing alternating layers of dough and bakery fat and (ii) maintaining this multilayered structure during processing to allow for steam entrapment for proper dough lift during baking. Although most authors agree on the importance of gluten and fat for maintaining the integrity of the different layers, detailed studies on their specific function are lacking. The exact mechanism of steam entrapment during dough lift and the relative contribution of water set free from the fat phase during baking also remain unclear. This review brings together current knowledge on pastry products and the factors determining (intermediate) product quality. Its focus is on flour constituents, fat, water, and (where applicable) yeast during the different production stages of pastry products. Future research needs are addressed as the knowledge on biochemical and physical changes occurring in flour constituents and other ingredients during pastry production and their effect on product quality is currently inadequate.

Research on evacuation in the subway station in China based on the Combined Social Force Model

NASA Astrophysics Data System (ADS)

Wan, Jiahui; Sui, Jie; Yu, Hua

2014-01-01

With the increasing number of subway stations, more and more attention has been paid to their emergency evacuation, as it plays an important part in urban emergency management. The present paper puts forward a method of crowd evacuation simulation for bioterrorism in subway station environment using the basic theory of the Social Force Model combined with the Gaussian Puff Model. A Combined Social Force Model is developed which is suitable for a real situation where there is a sudden toxic gas event. The model can also be used to demonstrate some individual behaviors in evacuation, such as competitive, grouping and herding. At last a series of experiments are conducted and the results are as follows. (1) When there is a toxic gas terroristic attack in subway stations, the influence on passengers varies according to the position that the gas source lies in and the numbers of gas sources. (2) More casualties will occur if managers do not detect the toxic gas danger and inform passengers about it. (3) The larger the wind speed is, the smaller the number of injured passengers will be. With the experiments, the number of people affected and other parameters like gas concentration can be estimated, which could support rapid and efficient emergency decisions.

Simulation Study of CO2-EOR in Tight Oil Reservoirs with Complex Fracture Geometries

PubMed Central

Zuloaga-Molero, Pavel; Yu, Wei; Xu, Yifei; Sepehrnoori, Kamy; Li, Baozhen

2016-01-01

The recent development of tight oil reservoirs has led to an increase in oil production in the past several years due to the progress in horizontal drilling and hydraulic fracturing. However, the expected oil recovery factor from these reservoirs is still very low. CO2-based enhanced oil recovery is a suitable solution to improve the recovery. One challenge of the estimation of the recovery is to properly model complex hydraulic fracture geometries which are often assumed to be planar due to the limitation of local grid refinement approach. More flexible methods like the use of unstructured grids can significantly increase the computational demand. In this study, we introduce an efficient methodology of the embedded discrete fracture model to explicitly model complex fracture geometries. We build a compositional reservoir model to investigate the effects of complex fracture geometries on performance of CO2 Huff-n-Puff and CO2 continuous injection. The results confirm that the appropriate modelling of the fracture geometry plays a critical role in the estimation of the incremental oil recovery. This study also provides new insights into the understanding of the impacts of CO2 molecular diffusion, reservoir permeability, and natural fractures on the performance of CO2-EOR processes in tight oil reservoirs. PMID:27628131

Electronic Cigarettes and Indoor Air Quality: A Simple Approach to Modeling Potential Bystander Exposures to Nicotine

PubMed Central

Colard, Stéphane; O’Connell, Grant; Verron, Thomas; Cahours, Xavier; Pritchard, John D.

2014-01-01

There has been rapid growth in the use of electronic cigarettes (“vaping”) in Europe, North America and elsewhere. With such increased prevalence, there is currently a debate on whether the aerosol exhaled following the use of e-cigarettes has implications for the quality of air breathed by bystanders. Conducting chemical analysis of the indoor environment can be costly and resource intensive, limiting the number of studies which can be conducted. However, this can be modelled reasonably accurately based on empirical emissions data and using some basic assumptions. Here, we present a simplified model, based on physical principles, which considers aerosol propagation, dilution and extraction to determine the potential contribution of a single puff from an e-cigarette to indoor air. From this, it was then possible to simulate the cumulative effect of vaping over time. The model was applied to a virtual, but plausible, scenario considering an e-cigarette user and a non-user working in the same office space. The model was also used to reproduce published experimental studies and showed good agreement with the published values of indoor air nicotine concentration. With some additional refinements, such an approach may be a cost-effective and rapid way of assessing the potential exposure of bystanders to exhaled e-cigarette aerosol constituents. PMID:25547398

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Weiguo; Shaw, William J.

This paper compares the wind field from a diagnostic model (CALMET) over complex terrain in the Phoenix region in the USA with observations that are gridded by a state-of-the-art Four-Dimensional Data Assimilation (FDDA) system. The wind difference between the CALMET and FDDA wind fields is larger at night than in the day. The magnitude of the wind difference can be smaller than 5% of the mean wind speed at low levels in areas with dense observational stations, while it can be larger than 80% in areas without observational stations or at high altitudes. The vector-mean wind direction difference over themore » domain is 15 deg on the surface level and 25 deg between 10 and 1500 m. To evaluate the effects of the wind difference on dispersion calculations, dispersion of a hypothetical passive tracer released from surface point sources is simulated by the second-order closure integrated puff (SCIPUFF) model driven by the CALMET and FDDA wind fields, respectively. Differences in the two simulated tracer concentration fields increase with time due to accumulation of effects of the wind differences both near the surface and at higher altitudes. Even for the release in the area with the densest distribution of surface stations, the relative difference in the peak surface concentration from CALMET-SCIPUFF and from FDDA-SCIPUFF is less than 10% only within 0.5 hr after the release in the afternoon, and increases to 70% at 1.5 hr; this is because of large differences in wind above the surface. For the release in the area with few stations, the difference can be larger than 100% or even larger after 1.5 hr from the release. To improve dispersion simulations driven by the CALMET wind in the region, observations at upper-air stations are needed and the current surface observation network needs to be reorganized or more stations are needed to account for the influence of terrain.« less

Expedition Six Flight Engineer Donald R. Pettit is loading software on PC in U.S. Lab

NASA Image and Video Library

2002-12-06

ISS006-E-07133 (9 December 2002) --- Astronaut Donald R. Pettit, Expedition 6 NASA ISS science officer, works to set up Pulmonary Function in Flight (PuFF) hardware in preparation for a Human Research Facility (HRF) experiment in the Destiny laboratory on the International Space Station (ISS). Expedition 6 is the fourth and final expedition crew to perform the HRF/PuFF Experiment on the ISS.

Expedition Six Flight Engineer Donald R. Pettit is loading software on PC in U.S. Lab

NASA Image and Video Library

2002-12-06

ISS006-E-07134 (9 December 2002) --- Astronaut Donald R. Pettit, Expedition Six NASA ISS science officer, works to set up Pulmonary Function in Flight (PuFF) hardware in preparation for a Human Research Facility (HRF) experiment in the Destiny laboratory on the International Space Station (ISS). Expedition Six is the fourth and final expedition crew to perform the HRF/PuFF Experiment on the ISS.

Gulf Petro Initiative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fathi Boukadi

2011-02-05

In this report, technologies for petroleum production and exploration enhancement in deepwater and mature fields are developed through basic and applied research by: (1) Designing new fluids to efficiently drill deepwater wells that can not be cost-effectively drilled with current technologies. The new fluids will be heavy liquid foams that have low-density at shallow dept to avoid formation breakdown and high density at drilling depth to control formation pressure. The goal of this project is to provide industry with formulations of new fluids for reducing casing programs and thus well construction cost in deepwater development. (2) Studying the effects ofmore » flue gas/CO{sub 2} huff n puff on incremental oil recovery in Louisiana oilfields bearing light oil. An artificial neural network (ANN) model will be developed and used to map recovery efficiencies for candidate reservoirs in Louisiana. (3) Arriving at a quantitative understanding for the three-dimensional controlled-source electromagnetic (CSEM) geophysical response of typical Gulf of Mexico hydrocarbon reservoirs. We will seek to make available tools for the qualitative, rapid interpretation of marine CSEM signatures, and tools for efficient, three-dimensional subsurface conductivity modeling.« less

Relationship between frequency power spectra and intermittent, large-amplitude bursts in the Alcator C-Mod scrape-off layer

NASA Astrophysics Data System (ADS)

Theodorsen, A.; Garcia, O. E.; Kube, R.; LaBombard, B.; Terry, J. L.

2017-11-01

Fluctuations in the boundary region of the Alcator C-Mod tokamak have been analyzed using gas puff imaging data from a set of Ohmically heated plasma density scan experiments. It is found that the relative fluctuation amplitudes are modest and close to normally distributed at the separatrix but become increasingly larger and skewed towards the main chamber wall. The frequency power spectra are nevertheless similar for all radial positions and line-averaged densities. Predictions of a stochastic model, describing the plasma fluctuations as a super-position of uncorrelated pulses, are shown to be in excellent agreement with the measurements. This implies that the pulse duration is the same, while the degree of pulse overlap decreases radially outwards in the scrape-off layer. The universal frequency power spectral density is thus determined by the shape and duration of the large-amplitude bursts associated with blob-like structures. The model also describes the rate of threshold level crossings, for which the exponential tails underline the intermittency of the fluctuations in the far scarpe-off layer.

Interactive Volcano Studies and Education Using Virtual Globes

NASA Astrophysics Data System (ADS)

Dehn, J.; Bailey, J. E.; Webley, P.

2006-12-01

Internet-based virtual globe programs such as Google Earth provide a spatial context for visualization of monitoring and geophysical data sets. At the Alaska Volcano Observatory, Google Earth is being used to integrate satellite imagery, modeling of volcanic eruption clouds and seismic data sets to build new monitoring and reporting tools. However, one of the most useful information sources for environmental monitoring is under utilized. Local populations, who have lived near volcanoes for decades are perhaps one of the best gauges for changes in activity. Much of the history of the volcanoes is only recorded through local legend. By utilizing the high level of internet connectivity in Alaska, and the interest of secondary education in environmental science and monitoring, it is proposed to build a network of observation nodes around local schools in Alaska and along the Aleutian Chain. A series of interactive web pages with observations on a volcano's condition, be it glow at night, puffs of ash, discolored snow, earthquakes, sounds, and even current weather conditions can be recorded, and the users will be able to see their reports in near real time. The database will create a KMZ file on the fly for upload into the virtual globe software. Past observations and legends could be entered to help put a volcano's long-term activity in perspective. Beyond the benefit to researchers and emergency managers, students and teachers in the rural areas will be involved in volcano monitoring, and gain an understanding of the processes and hazard mitigation efforts in their community. K-12 students will be exposed to the science, and encouraged to participate in projects at the university. Infrastructure at the university can be used by local teachers to augment their science programs, hopefully encouraging students to continue their education at the university level.

Have combustible cigarettes met their match? The nicotine delivery profiles and harmful constituent exposures of second-generation and third-generation electronic cigarette users

PubMed Central

Wagener, Theodore L; Floyd, Evan L; Stepanov, Irina; Driskill, Leslie M; Frank, Summer G; Meier, Ellen; Leavens, Eleanor L; Tackett, Alayna P; Molina, Neil; Queimado, Lurdes

2017-01-01

Introduction Electronic cigarettes’ (e-cigarettes) viability as a public health strategy to end smoking will likely be determined by their ability to mimic the pharmacokinetic profile of a cigarette while also exposing users to significantly lower levels of harmful/potentially harmful constituents (HPHCs). The present study examined the nicotine delivery profile of third- (G3) versus second-generation (G2) e-cigarette devices and their users’ exposure to nicotine and select HPHCs compared with cigarette smokers. Methods 30 participants (10 smokers, 9 G2 and 11 G3 users) completed baseline questionnaires and provided exhaled carbon monoxide (eCO), saliva and urine samples. Following a 12-hour nicotine abstinence, G2 and G3 users completed a 2-hour vaping session (ie, 5 min, 10-puff bout followed by ad libitum puffing for 115 min). Blood samples, subjective effects, device characteristics and e-liquid consumption were assessed. Results Smokers, G2 and G3 users had similar baseline levels of cotinine, but smokers had 4 and 7 times higher levels of eCO (p<0.0001) and total 4-(Methylnitrosamino)-1-(3-pyridyl)-1-butanol (i.e., NNAL, p<0.01), respectively, than G2 or G3 users. Compared with G2s, G3 devices delivered significantly higher power to the atomiser, but G3 users vaped e-cigarette liquids with significantly lower nicotine concentrations. During the vaping session, G3 users achieved significantly higher plasma nicotine concentrations than G2 users following the first 10 puffs (17.5 vs 7.3 ng/mL, respectively) and at 25 and 40 min of ad libitum use. G3 users consumed significantly more e-liquid than G2 users. Vaping urges/withdrawal were reduced following 10 puffs, with no significant differences between device groups. Discussion Under normal use conditions, both G2 and G3 devices deliver cigarette-like amounts of nicotine, but G3 devices matched the amount and speed of nicotine delivery of a conventional cigarette. Compared with cigarettes, G2 and G3 e-cigarettes resulted in significantly lower levels of exposure to a potent lung carcinogen and cardiovascular toxicant. These findings have significant implications for understanding the addiction potential of these devices and their viability/suitability as aids to smoking cessation. PMID:27729564

Quantitative Assessment of Detection Frequency for the INL Ambient Air Monitoring Network

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sondrup, A. Jeffrey; Rood, Arthur S.

A quantitative assessment of the Idaho National Laboratory (INL) air monitoring network was performed using frequency of detection as the performance metric. The INL air monitoring network consists of 37 low-volume air samplers in 31 different locations. Twenty of the samplers are located on INL (onsite) and 17 are located off INL (offsite). Detection frequencies were calculated using both BEA and ESER laboratory minimum detectable activity (MDA) levels. The CALPUFF Lagrangian puff dispersion model, coupled with 1 year of meteorological data, was used to calculate time-integrated concentrations at sampler locations for a 1-hour release of unit activity (1 Ci) formore » every hour of the year. The unit-activity time-integrated concentration (TICu) values were calculated at all samplers for releases from eight INL facilities. The TICu values were then scaled and integrated for a given release quantity and release duration. All facilities modeled a ground-level release emanating either from the center of the facility or at a point where significant emissions are possible. In addition to ground-level releases, three existing stacks at the Advanced Test Reactor Complex, Idaho Nuclear Technology and Engineering Center, and Material and Fuels Complex were also modeled. Meteorological data from the 35 stations comprising the INL Mesonet network, data from the Idaho Falls Regional airport, upper air data from the Boise airport, and three-dimensional gridded data from the weather research forecasting model were used for modeling. Three representative radionuclides identified as key radionuclides in INL’s annual National Emission Standards for Hazardous Air Pollutants evaluations were considered for the frequency of detection analysis: Cs-137 (beta-gamma emitter), Pu-239 (alpha emitter), and Sr-90 (beta emitter). Source-specific release quantities were calculated for each radionuclide, such that the maximum inhalation dose at any publicly accessible sampler or the National Emission Standards for Hazardous Air Pollutants maximum exposed individual location (i.e., Frenchman’s Cabin) was no more than 0.1 mrem yr–1 (i.e., 1% of the 10 mrem yr–1 standard). Detection frequencies were calculated separately for the onsite and offsite monitoring network. As expected, detection frequencies were generally less for the offsite sampling network compared to the onsite network. Overall, the monitoring network is very effective at detecting the potential releases of Cs-137 or Sr-90 from all sources/facilities using either the ESER or BEA MDAs. The network was less effective at detecting releases of Pu-239. Maximum detection frequencies for Pu-239 using ESER MDAs ranged from 27.4 to 100% for onsite samplers and 3 to 80% for offsite samplers. Using BEA MDAs, the maximum detection frequencies for Pu-239 ranged from 2.1 to 100% for onsite samplers and 0 to 5.9% for offsite samplers. The only release that was not detected by any of the samplers under any conditions was a release of Pu-239 from the Idaho Nuclear Technology and Engineering Center main stack (CPP-708). The methodology described in this report could be used to improve sampler placement and detection frequency, provided clear performance objectives are defined.« less

Special population planner, version 4.0.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuiper, J.; Tanzman, E.; Metz, W.

2007-03-26

Emergencies happen every day. Many are caused by storms or auto accidents and can be planned for, if not predicted. Emergencies resulting from natural hazards often affect a large number of people, and planning for them can be difficult, since knowledge of the needs of the people involved is generally unavailable. Emergencies resulting from accidents at industrial and military facilities can also be large scale in nature if people must be evacuated or sheltered in place. Federal planning for large scale emergencies is the responsibility of the Federal Emergency Management Agency (FEMA), which provides assistance to various emergency management agenciesmore » at the national, state and local level. More information about FEMA is available at http://www.fema.gov/. The purpose of the Special Population Planner (SPP) is to help emergency planners address the needs of persons with special needs. The exact definition of 'special population' is a policy decision. Policymakers have included a variety of groups in this term, such as persons with disabilities, those who do not have vehicles with which to evacuate, children who are unattended at times (latchkey children), and many others. The SPP was developed initially for the Alabama Emergency Management Agency as part of its Chemical Stockpile Emergency Preparedness Program (CSEPP), which aids emergency planning and preparedness in communities surrounding military installations across the United States where chemical weapons are stored pending their destruction under federal law. Like that specialized application, this open-source version contains a set of specialized Geographic Information System (GIS) tools to facilitate emergency planning on behalf of persons with special needs, regardless of how the term is defined. While the original SPP system was developed for emergency planning relating to chemical hazards, it can be applied to other threats as well. It is apparent from Hurricane Katrina and other natural and man-made disasters that many of the problems posed by emergency planning for a chemical weapons agent release are shared by other hazards as well. The notion that emergency planning shares common functions underlies the decision by FEMA to include the Chemical Stockpile Emergency Preparedness Program (CSEPP) in its 'all-hazards' planning approach. The CSEPP's official planning guidance operationalizes this approach by suggesting that state and local CSEPP emergency plans 'should be appended to the existing all-hazards emergency plan.' The SPP is programmed as a set of tools within an ESRI ArcMap 9.1 project. ArcMap is a component of both ESRI ArcGIS 9.1 and ESRI ArcView 9.1, and it provides a rich GIS user interface for viewing spatial and tabular data, analyzing it, and producing output reports and maps. This GIS interface has been augmented with the SPP tools for a user interface that provides custom functionality for emergency planning. The system as released also includes some hypothetical example records for special needs populations, facilities, resources, control points and sirens sufficient for showing how the system would work with real information. A GIS database is included with some publicly available example layers. The SPP is designed to support emergency planners as they address emergency management issues, and includes capabilities that support the collection and importing of data, the review of data in a spatial context, and GIS tools for emergency planning. The SPP system allows for the identification and categorization of response zones to allow for multiple levels of preparedness. An Immediate Response Zone (IRZ) might be designated as the area 0 to 10 miles from a facility where the response would be the most urgent. SPP can support more than one set of planning zones to accommodate different types of emergencies or the different jurisdictions of emergency response organizations. These areas can be delineated by any number of criteria that make sense for the area. An area like New Orleans might designate response zones based on the depth above/below sea level, or an urban area may categorize an IRZ as the 'central business district' with the PAZ encompassing the larger outlying area. Many of the sites involved in the CSEPP currently use an integrated emergency response information system to support their emergency management planning. The D2-Puff system (including or WebPuff 2.1) by Innovative Emergency Management, Inc. is the main software serving this purpose. More information on D2-Puff can be found at www.ieminc.com. SPP differs from D2-Puff in that it is designed for planning, not response to assist those with special needs, is programmed within a popular commercial GIS software system, and can be loaded with large amounts of data to support all hazards emergency planning.« less

An End-to-End Model of Plant Pheromone Channel for Long Range Molecular Communication.

PubMed

Unluturk, Bige D; Akyildiz, Ian F

2017-01-01

A new track in molecular communication is using pheromones which can scale up the range of diffusion-based communication from μm meters to meters and enable new applications requiring long range. Pheromone communication is the emission of molecules in the air which trigger behavioral or physiological responses in receiving organisms. The objective of this paper is to introduce a new end-to-end model which incorporates pheromone behavior with communication theory for plants. The proposed model includes both the transmission and reception processes as well as the propagation channel. The transmission process is the emission of pheromones from the leaves of plants. The dispersion of pheromones by the flow of wind constitutes the propagation process. The reception process is the sensing of pheromones by the pheromone receptors of plants. The major difference of pheromone communication from other molecular communication techniques is the dispersion channel acting under the laws of turbulent diffusion. In this paper, the pheromone channel is modeled as a Gaussian puff, i.e., a cloud of pheromone released instantaneously from the source whose dispersion follows a Gaussian distribution. Numerical results on the performance of the overall end-to-end pheromone channel in terms of normalized gain and delay are provided.

Modified ensemble Kalman filter for nuclear accident atmospheric dispersion: prediction improved and source estimated.

PubMed

Zhang, X L; Su, G F; Yuan, H Y; Chen, J G; Huang, Q Y

2014-09-15

Atmospheric dispersion models play an important role in nuclear power plant accident management. A reliable estimation of radioactive material distribution in short range (about 50 km) is in urgent need for population sheltering and evacuation planning. However, the meteorological data and the source term which greatly influence the accuracy of the atmospheric dispersion models are usually poorly known at the early phase of the emergency. In this study, a modified ensemble Kalman filter data assimilation method in conjunction with a Lagrangian puff-model is proposed to simultaneously improve the model prediction and reconstruct the source terms for short range atmospheric dispersion using the off-site environmental monitoring data. Four main uncertainty parameters are considered: source release rate, plume rise height, wind speed and wind direction. Twin experiments show that the method effectively improves the predicted concentration distribution, and the temporal profiles of source release rate and plume rise height are also successfully reconstructed. Moreover, the time lag in the response of ensemble Kalman filter is shortened. The method proposed here can be a useful tool not only in the nuclear power plant accident emergency management but also in other similar situation where hazardous material is released into the atmosphere. Copyright © 2014 Elsevier B.V. All rights reserved.

Numerical Simulations of Airflows and Tracer Transport in the Southwestern United States.

NASA Astrophysics Data System (ADS)

Yamada, Tetsuji

2000-03-01

Project MOHAVE (Measurement of Haze and Visual Effects) produced a unique set of tracer data over the southwestern United States. During the summer of 1992, a perfluorocarbon tracer gas was released from the Mohave Power Project (MPP), a large coal-fired facility in southern Nevada. Three-dimensional atmospheric models, the Higher-Order Turbulence Model for Atmospheric Circulation-Random Puff Transport and Diffusion (HOTMAC-RAPTAD), were used to simulate the concentrations of tracer gas that were observed during a portion of the summer intensive period of Project MOHAVE. The study area extended from northwestern Arizona to southern Nevada and included Lake Mead, the Colorado River Valley, the Grand Canyon National Park, and MPP. The computational domain was 368 km in the east-west direction by 252 km in the north-south direction. Rawinsonde and radar wind profiler data were used to provide initial and boundary conditions to HOTMAC simulations. HOTMAC with a horizontal grid spacing of 4 km was able to simulate the diurnal variations of drainage and upslope flows along the Grand Canyon and Colorado River Valley. HOTMAC also captured the diurnal variations of turbulence, which played important roles for the transport and diffusion simulations by RAPTAD. The modeled tracer gas concentrations were compared with observations. The model's performance was evaluated statistically.

People's Instinctive Travels and the Paths to Rhythms: Hip-Hop's Continuation of the Enduring Tradition of African and African American Rhetorical Forms and Tropes

ERIC Educational Resources Information Center

Welbeck, Timothy N.

2017-01-01

Hip-hop is an African folk art birthed in America. Whether one simply observes the tonal language that puffs the breath of life into the lyric prose of rap music, the poly-rhythms of the "boom-bap" rhythmic phrasings that became a fixture of New York rap music in the late 1980s, the winding syncopation from the pounding "808"…

European Scientific Notes. Volume 37, Number 6.

DTIC Science & Technology

1983-06-30

8217) , but did no--t- appear to he smoking gas -plizse componrnt may b ",,.:dictivt" a ny., por e cigarettes.’ Puff doLir a t ionri ,Indtsf Thuslaen ihC...Glasgow) reviewed current medical such as iodine 131 and indium 111. applications of polymers and discussed Photon correlation spectroscopy of recent...results from his own laboratory. scattered laser light is used to measure The low diffusion constants for most the particle sizes. Davis also discuss

Clove cigarette smoking: biochemical, physiological, and subjective effects.

PubMed

Malson, Jennifer L; Lee, Eun M; Murty, Ram; Moolchan, Eric T; Pickworth, Wallace B

2003-02-01

Alternative tobacco products such as clove (kreteks) and bidi cigarettes have become increasingly popular among US smokers. The nicotine content of a popular clove cigarette (Djarum Special) filler averaged 7.4 mg; conventional cigarettes contained 13.0 mg. However, smoke yields from standardized machine-smoking analysis indicated it delivered more nicotine, carbon monoxide (CO), and tar than conventional cigarettes. In a clinical study, nicotine delivery, physiologic, and subjective effects of the clove cigarette were compared to their own brand of cigarette in 10 adult smokers (7 males). Average time to smoke the clove cigarette (549 s) and number of puffs (15.1) were significantly greater than own brand (314 s and 9.4 puffs). Increases in venous plasma nicotine and exhaled CO after smoking the clove cigarette (17.4 ng/ml; 6 ppm) were similar to those after own brand (17.6 ng/ml; 4.5 ppm). Maximal changes in heart rate (HR), systolic, and diastolic blood pressures (BP) did not differ significantly between the clove and own brand of cigarette. Compared to their own brand of cigarette, the clove cigarette was rated as better tasting and being distinctly different. Our findings indicate that clove cigarettes deliver significant quantities of nicotine, CO, and presumably other toxic components of tobacco smoke. Taste satisfaction, aromatic odor, and novelty may contribute to their appeal to young smokers.

Altered lung biology of healthy never smokers following acute inhalation of E-cigarettes.

PubMed

Staudt, Michelle R; Salit, Jacqueline; Kaner, Robert J; Hollmann, Charleen; Crystal, Ronald G

2018-05-14

Little is known about health risks associated with electronic cigarette (EC) use although EC are rising in popularity and have been advocated as a means to quit smoking cigarettes. Ten never-smokers, without exposure history to tobacco products or EC, were assessed at baseline with questionnaire, chest X-ray, lung function, plasma levels of endothelial microparticles (EMP), and bronchoscopy to obtain small airway epithelium (SAE) and alveolar macrophages (AM). One week later, subjects inhaled 10 puffs of "Blu" brand EC, waited 30 min, then another 10 puff; n = 7 were randomized to EC with nicotine and n = 3 to EC without nicotine to assess biological responses in healthy, naive individuals. Two hr. post-EC exposure, subjects were again assessed as at baseline. No significant changes in clinical parameters were observed. Biological changes were observed compared to baseline, including altered transcriptomes of SAE and AM for all subjects and elevated plasma EMP levels following inhalation of EC with nicotine. This study provides in vivo human data demonstrating that acute inhalation of EC aerosols dysregulates normal human lung homeostasis in a limited cohort of healthy naïve individuals. These observations have implications to new EC users, nonsmokers exposed to secondhand EC aerosols and cigarette smokers using EC to quit smoking. ClinicalTrials.gov NCT01776398 (registered 10/12/12), NCT02188511 (registered 7/2/14).

Method for the Determination of Carbonyl Compounds in E-Cigarette Aerosols

PubMed Central

Flora, Jason W.; Wilkinson, Celeste T.; Wilkinson, James W.; Lipowicz, Peter J.; Skapars, James A.; Anderson, Adam; Miller, John H.

2017-01-01

Low levels of thermal degradation products such as carbonyls (formaldehyde, acetaldehyde, acrolein, crotonaldehyde) have been reported in e-cigarette aerosols. The collection and analysis of e-cigarette aerosol carbonyls are often adapted from methods developed for tobacco cigarette smoke. These methodologies are often not sensitive enough to detect low carbonyl levels in e-cigarette aerosols. One objective of this work was to develop and validate a rapid, selective and sensitive ultra-performance liquid chromatography with mass spectrometry method optimized for analysis of carbonyls in e-cigarette aerosols. Aerosols were trapped in 20-puff collections, 4-s durations, 55-mL volumes, 30-s intervals, square wave puff profiles. Collection apparatus involved a linear smoking machine with Cambridge filter pad followed by a glass impinger containing acidified 2,4-dinitrophenylhydrazine. This method showed limits of quantitation and detection of 0.016 and 0.003 µg puff−1, respectively, and run time of 4 min. Six e-cigarettes were evaluated (five devices each). All contained measurable levels of carbonyls. Levels were mostly well below those in conventional cigarettes. However, for some e-cigarettes, formaldehyde levels were above those for tobacco cigarettes (highest at 14.1 µg puff−1). Temperatures related to carbonyl yields in e-cigarette aerosols were explored to better understand carbonyl formation: formation of formaldehyde is low at temperatures below 350°C. PMID:28087758

Lack of effect of menthol level and type on smokers' estimated mouth level exposures to tar and nicotine and perceived sensory characteristics of cigarette smoke.

PubMed

Ashley, Madeleine; Dixon, Mike; Sisodiya, Ajit; Prasad, Krishna

2012-08-01

Menthol can reduce sensory irritation and it has been hypothesised that this could result in smokers of mentholated cigarettes taking larger puffs and deeper post-puff inhalations thereby obtaining higher exposures to smoke constituents than smokers of non-mentholated cigarettes. The aim of our study was to use part-filter analysis methodology to assess the effects of cigarette menthol loading on regular and occasional smokers of mentholated cigarettes. We measured mouth level exposure to tar and nicotine and investigated the effects of mentholation on smokers' sensory perceptions such as cooling and irritation. Test cigarettes were produced containing no menthol and different loadings of synthetic and natural l-menthol at 1 and 4mg ISO tar yields. A target of 100 smokers of menthol cigarettes and 100 smokers who predominantly smoked non-menthol cigarettes from both 1 and 4mg ISO tar yield categories were recruited in Poland and Japan. Each subject was required to smoke the test cigarette types of their usual ISO tar yield. There were positive relationships between menthol loading and the perceived 'strength of menthol taste' and 'cooling' effect. However, we did not see marked menthol-induced reductions in perceived irritation or menthol-induced increases in mouth level exposure to tar and nicotine. Copyright © 2012 Elsevier Inc. All rights reserved.

An Experiment Investigation of Fully-Modulated, Turbulent Diffusion Flames in Reduced Gravity

NASA Technical Reports Server (NTRS)

Hermanson, J. C.; Johari, H.; Usowicz, J. E.; Stocker, D. P.; Nagashima, T.; Obata, S.

1999-01-01

Pulsed combustion appears to have the potential to provide for rapid fuel/air mixing, compact and economical combustors, and reduced exhaust emissions. The ultimate objective of this program is to increase the fundamental understanding of the fuel/air mixing and combustion behavior of pulsed, turbulent diffusion flames by conducting experiments in microgravity. In this research the fuel jet is fully-modulated (i.e., completely shut off between pulses) by an externally controlled valve system. This can give rise to drastic modification of the combustion and flow characteristics of flames, leading to enhanced fuel/air mixing mechanisms not operative for the case of acoustically excited or partially-modulated jets. In addition, the fully-modulated injection approach avoids the strong acoustic forcing present in pulsed combustion devices, significantly simplifying the mixing and combustion processes. Relatively little is known of the behavior of turbulent flames in reduced-gravity conditions, even in the absence of pulsing. The goal of this Flight-Definition experiment (PUFF, for PUlsed-Fully Flames) is to establish the behavior of fully-modulated, turbulent diffusion flames under microgravity conditions. Fundamental issues to be addressed in this experiment include the mechanisms responsible for the flame length decrease for fully-modulated, turbulent diffusion flames compared with steady flames, the impact of buoyancy on the mixing and combustion characteristics of these flames, and the characteristics of turbulent flame puffs under fully momentum-dominated conditions.

Characterizing smoking topography of cannabis in heavy users

PubMed Central

Stitzer, Maxine L.; Vandrey, Ryan

2013-01-01

Rationale Little is known about the smoking topography characteristics of heavy cannabis users. Such measures may be able to predict cannabis use-related outcomes and could be used to validate self-reported measures of cannabis use. Objectives The current study was conducted to measure cannabis smoking topography characteristics during periods of ad libitum use and to correlate topography assessments with measures of self-reported cannabis use, withdrawal and craving during abstinence, and cognitive task performance. Methods Participants (N=20) completed an inpatient study in which they alternated between periods of ad libitum cannabis use and abstinence. Measures of self-reported cannabis use, smoking topography, craving, withdrawal, and sleep measures were collected. Results Participants smoked with greater intensity (e.g., greater volume, longer duration) on initial cigarette puffs with a steady decline on subsequent puffs. Smoking characteristics were significantly correlated with severity of withdrawal, notably sleep quality and architecture, and craving during abstinence, suggesting dose-related effects of cannabis use on these outcomes. Smoking characteristics generally were not significantly associated with cognitive performance. Smoking topography measures were significantly correlated with self-reported measures of cannabis use, indicating validity of these assessments, but topography measures were more sensitive than self-report in predicting cannabis-related outcomes. Conclusions A dose–effect relationship between cannabis consumption and outcomes believed to be clinically important was observed. With additional research, smoking topography assessments may become a useful clinical tool. PMID:21922170

Disruption of trace conditioning of the nictitating membrane response in rabbits by central cholinergic blockade.

PubMed

Kaneko, T; Thompson, R F

1997-05-01

Central muscarinic cholinergic involvement in classical conditioning of eyeblink responses was determined in trace and delay paradigms. Rabbits were trained on a trace procedure in which a 250-ms tone conditioned stimulus (CS) and a 100-ms air-puff unconditioned stimulus (UCS) were presented with a 500-ms trace interval. Each training session day consisted of ten tone alone, ten air-puff alone and 80 paired CS-UCS trials. Scopolamine hydrochloride at doses of 0.03 and 0.1 mg/0.5 ml per kg, s.c. dose-dependently disrupted acquisition of conditioned responses. Rabbits that were treated with scopolamine and failed to learn showed a gradual increase in conditioned responses during an additional training period with saline injections and no transfer from earlier training. Scopolamine methyl bromide, which does not appreciably cross the blood-brain barrier, showed no effects in the trace conditioning paradigm at a dose of 0.1 mg/kg, s.c., indicating central cholinergic blockade is responsible for the suppressive effect of scopolamine. Scopolamine hydrochloride at a dose of 0.1 mg/kg, s.c. did not block acquisition in the delay procedure with a 250-ms inter-stimulus interval, although the rate of acquisition was somewhat reduced by the drug. These data are the first to demonstrate that classical conditioning of the eyeblink response in the trace procedure is highly sensitive to central cholinergic deficits.

Cigar burning under different smoking intensities and effects on emissions.

PubMed

Dethloff, Ole; Mueller, Christian; Cahours, Xavier; Colard, Stéphane

2017-12-01

The effect of smoking intensity on cigar smoke emissions was assessed under a range of puff frequencies and puff volumes. In order to potentially reduce emissions variability and to identify patterns as accurately as possible, cigar weights and diameters were measured, and outliers were excluded prior to smoking. Portions corresponding to 25%, 50%, 75% and 100% of the cigar, measured down to the butt length, were smoked under several smoking conditions, to assess nicotine, CO and water yields. The remaining cigar butts were analysed for total alkaloids, nicotine, and moisture. Results showed accumulation effects during the burning process having a significant impact on smoke emission levels. Condensation and evaporation occur and lead to smoke emissions dependent on smoking intensity. Differences were observed for CO on one side as a gas phase compound and nicotine on the other side as a particulate phase compound. For a given intensity, while CO emission increases linearly as the cigar burns, nicotine and water emissions exhibited an exponential increase. Our investigations showed that a complex phenomena occurs during the course of cigar smoking which makes emission data: difficult to interpret, is potentially misleading to the consumer, and inappropriate for exposure assessment. The results indicate that, tobacco content and physical parameters may well be the most robust basis for product characterisation and comparison rather than smoke emission. Copyright © 2017 Elsevier Inc. All rights reserved.

Laser-plasma extreme ultraviolet and soft X-ray sources based on a double stream gas puff target: interaction of the radiation pulses with matter

NASA Astrophysics Data System (ADS)

Bartnik, A.

2015-06-01

In this work a review of investigations concerning interaction of intense extreme ultraviolet (EUV) and soft X-ray (SXR) pulses with matter is presented. The investigations were performed using laser-produced plasma (LPP) EUV/SXR sources based on a double stream gas puff target. The sources are equipped with dedicated collectors allowing for efficient focusing of the EUV/SXR radiation pulses. Intense radiation in a wide spectral range, as well as a quasi-monochromatic radiation can be produced. In the paper different kinds of LPP EUV/SXR sources developed in the Institute of Optoelectronics, Military University of Technology are described. Radiation intensities delivered by the sources are sufficient for different kinds of interaction experiments including EUV/SXR induced ablation, surface treatment, EUV fluorescence or photoionized plasma creation. A brief review of the main results concerning this kind of experiments performed by author of the paper are presented. However, since the LPP sources cannot compete with large scale X-ray sources like synchrotrons, free electron lasers or high energy density plasma sources, it was indicated that some investigations not requiring extreme irradiation parameters can be performed using the small scale installations. Some results, especially concerning low temperature photoionized plasmas are very unique and could be hardly obtained using the large facilities.

Mainstream Smoke Levels of Volatile Organic Compounds in 50 US Domestic Cigarette Brands Smoked with the ISO and Canadian Intense Protocols

PubMed Central

Pazo, Daniel Y.; Moliere, Fallon; Sampson, Maureen M.; Reese, Christopher M.; Agnew-Heard, Kimberly A.; Walters, Matthew J.; Holman, Matthew R.; Blount, Benjamin C.; Watson, Clifford; Chambers, David M.

2017-01-01

Introduction A significant portion of the increased risk of cancer and respiratory disease from exposure to cigarette smoke is attributed to volatile organic compounds (VOCs). In this study, 21 VOCs were quantified in mainstream cigarette smoke from 50 U.S. domestic brand varieties that included high market share brands and two Kentucky research cigarettes (3R4F and 1R5F). Methods Mainstream smoke was generated under ISO 3308 and Canadian Intense (CI) smoking protocols with linear smoking machines with a gas sampling bag collection followed by SPME/GC/MS analysis. Results For both protocols, mainstream smoke VOC amounts among the different brand varieties were strongly correlated between the majority of the analytes. Overall, Pearson correlation (r) ranged from 0.68 to 0.99 for ISO and 0.36 to 0.95 for CI. However, monoaromatic compounds were found to increase disproportionately compared to unsaturated, nitro, and carbonyl compounds under the CI smoking protocol where filter ventilation is blocked. Conclusions Overall, machine generated “vapor phase” amounts (μg/cigarette) are primarily attributed to smoking protocol (e.g., blocking of vent holes, puff volume, and puff duration) and filter ventilation. A possible cause for the disproportionate increase in monoaromatic compounds could be increased pyrolysis under low oxygen conditions associated with the CI protocol. PMID:27113015

Benzene, benzo(a)pyrene, and lead in smoke from tobacco products other than cigarettes.

PubMed Central

Appel, B R; Guirguis, G; Kim, I S; Garbin, O; Fracchia, M; Flessel, C P; Kizer, K W; Book, S A; Warriner, T E

1990-01-01

Benzene, benzo(a)pyrene (BaP), and lead in mainstream smoke from cigars, roll-your-own (RYO) cigarette and pipe tobaccos were sampled to evaluate their potential health significance. Results with reference cigarettes were consistent with published values, providing support for the methodology employed. The emissions of benzene and BaP, expressed as mass emitted per gram of tobacco consumed, were similar for all products evaluated; for benzene, the mean values for cigars, RYO cigarette and pipe tobaccos were 156 +/- 52, 68 +/- 11, and 242 +/- 126 micrograms/g, respectively. Mean values for BaP were 42 +/- 7 and 48 +/- 4 ng/g for cigars and RYO cigarette tobacco, respectively. Lead values were below the limit of reliable quantitation in all cases. The mean benzene concentrations in a puff ranged from 1 to 2 x 10(5) micrograms/m3 for cigars, RYO cigarette and pipe tobaccos. For BaP, the puff concentration averaged about 60 micrograms/m3 for cigars and RYO cigarette tobacco. The results suggest that smoking cigars, pipes or RYO cigarettes leads to potential exposures which exceed the No Significant Risk levels of benzene and BaP set pursuant to California's Proposition 65. These tobacco products are now required to bear a health hazard warning when sold in California. We recommend that this be adopted as national policy. PMID:2327532

Recent improvements of the JET lithium beam diagnostica)

NASA Astrophysics Data System (ADS)

Brix, M.; Dodt, D.; Dunai, D.; Lupelli, I.; Marsen, S.; Melson, T. F.; Meszaros, B.; Morgan, P.; Petravich, G.; Refy, D. I.; Silva, C.; Stamp, M.; Szabolics, T.; Zastrow, K.-D.; Zoletnik, S.; JET-EFDA Contributors

2012-10-01

A 60 kV neutral lithium diagnostic beam probes the edge plasma of JET for the measurement of electron density profiles. This paper describes recent enhancements of the diagnostic setup, new procedures for calibration and protection measures for the lithium ion gun during massive gas puffs for disruption mitigation. New light splitting optics allow in parallel beam emission measurements with a new double entrance slit CCD spectrometer (spectrally resolved) and a new interference filter avalanche photodiode camera (fast density and fluctuation studies).

Characteristics of switching plasma in an inverse-pinch switch

NASA Technical Reports Server (NTRS)

Lee, Ja H.; Choi, Sang H.; Venable, Demetrius D.; Han, Kwang S.; Nam, Sang H.

1993-01-01

Characteristics of the plasma that switches on tens of giga volt-ampere in an inverse-pinch plasma switch (INPIStron) have been made. Through optical and spectroscopic diagnostics of the current carrying plasma, the current density, the motion of current paths, dominant ionic species have been determined in order to access their effects on circuit parameters and material erosion. Also the optimum operational condition of the plasma-puff triggering method required for azimuthally uniform conduction in the INPIStron has been determined.

Sensitivity analysis and uncertainty estimation in ash concentration simulations and tephra deposit daily forecasted at Mt. Etna, in Italy

NASA Astrophysics Data System (ADS)

Prestifilippo, Michele; Scollo, Simona; Tarantola, Stefano

2015-04-01

The uncertainty in volcanic ash forecasts may depend on our knowledge of the model input parameters and our capability to represent the dynamic of an incoming eruption. Forecasts help governments to reduce risks associated with volcanic eruptions and for this reason different kinds of analysis that help to understand the effect that each input parameter has on model outputs are necessary. We present an iterative approach based on the sequential combination of sensitivity analysis, parameter estimation procedure and Monte Carlo-based uncertainty analysis, applied to the lagrangian volcanic ash dispersal model PUFF. We modify the main input parameters as the total mass, the total grain-size distribution, the plume thickness, the shape of the eruption column, the sedimentation models and the diffusion coefficient, perform thousands of simulations and analyze the results. The study is carried out on two different Etna scenarios: the sub-plinian eruption of 22 July 1998 that formed an eruption column rising 12 km above sea level and lasted some minutes and the lava fountain eruption having features similar to the 2011-2013 events that produced eruption column high up to several kilometers above sea level and lasted some hours. Sensitivity analyses and uncertainty estimation results help us to address the measurements that volcanologists should perform during volcanic crisis to reduce the model uncertainty.

Evaluation of Nicotine Pharmacokinetics and Subjective Effects following Use of a Novel Nicotine Delivery System.

PubMed

Teichert, Axel; Brossard, Patrick; Felber Medlin, Loyse; Sandalic, Larissa; Franzon, Mikael; Wynne, Chris; Laugesen, Murray; Lüdicke, Frank

2018-03-06

Novel nicotine delivery systems represent an evolving part of the tobacco harm reduction strategy. The pharmacokinetic (PK) profile of nicotine delivered by P3L, a pulmonary nicotine delivery system, and its effects on smoking urges and craving relief in relation to Nicorette inhalator were evaluated. This open-label, ascending nicotine levels study was conducted in 16 healthy smokers. Three different nicotine delivery levels, 50, 80, and 150 µg/puff, delivered by the P3L system were evaluated consecutively on different days after the use of the Nicorette inhalator. Venous nicotine PK, subjective effects, and tolerability were assessed. Geometric least-squares means for maximum plasma nicotine concentration (Cmax), generated by the mixed-effect model for exposure comparison, were 9.7, 11.2, and 9.8 ng/mL for the 50, 80, and 150 µg/puff P3L variants, respectively, compared to 6.1 ng/mL after Nicorette inhalator use. Median time from product use start to Cmax was 7.0 minutes for all P3L, compared to 30.0 minutes for the Nicorette inhalator. Craving reduction was slightly faster than with the Nicorette inhalator as assessed with the visual analog scale craving score. The mean Questionnaire of Smoking Urges -brief total scores did not differ for both products. P3L was well tolerated. At all three nicotine levels tested, the inhalation of the nicotine lactate aerosol delivered with the P3L provided plasma nicotine concentrations higher and faster compared to the Nicorette inhalator. The plasma nicotine concentration-time profile supports a pulmonary route of absorption for P3L compared to the oromucosal absorption of the Nicorette inhalator. The combination of nicotine and lactic acid with the P3L device shows potential over existing nicotine delivery systems by delivering nicotine with kinetics close to published data on conventional cigarettes and without exogenous carrier substances as used in current electronic nicotine delivery systems. Altogether, the PK profile, subjective effects, and safety profile obtained in this study suggest P3L is an innovative nicotine delivery product that will be acceptable to adult smokers as an alternative to cigarettes.

Impaired delay and trace eyeblink conditioning in school-age children with fetal alcohol syndrome.

PubMed

Jacobson, Sandra W; Stanton, Mark E; Dodge, Neil C; Pienaar, Mariska; Fuller, Douglas S; Molteno, Christopher D; Meintjes, Ernesta M; Hoyme, H Eugene; Robinson, Luther K; Khaole, Nathaniel; Jacobson, Joseph L

2011-02-01

Classical eyeblink conditioning (EBC) involves contingent temporal pairing of a conditioned stimulus (e.g., tone) with an unconditioned stimulus (e.g., air puff). Impairment of EBC has been demonstrated in studies of alcohol-exposed animals and in children exposed prenatally at heavy levels. Fetal alcohol syndrome (FAS) was diagnosed by expert dysmorphologists in a large sample of Cape Coloured, South African children. Delay EBC was examined in a new sample of 63 children at 11.3 years, and trace conditioning in 32 of the same children at 12.8 years. At each age, 2 sessions of 50 trials each were administered on the same day; 2 more sessions the next day, for children not meeting criterion for conditioning. Six of 34 (17.6%) children born to heavy drinkers were diagnosed with FAS, 28 were heavily exposed nonsyndromal (HE), and 29 were nonexposed controls. Only 33.3% with FAS and 42.9% of HE met criterion for delay conditioning, compared with 79.3% of controls. The more difficult trace conditioning task was also highly sensitive to fetal alcohol exposure. Only 16.7% of the FAS and 21.4% of HE met criterion for trace conditioning, compared with 66.7% of controls. The magnitude of the effect of diagnostic group on trace conditioning was not greater than the effect on short delay conditioning, findings consistent with recent rat studies. Longer latency to onset and peak eyeblink CR in exposed children indicated poor timing and failure to blink in anticipation of the puff. Extended training resulted in some but not all of the children reaching criterion. These data showing alcohol-related delay and trace conditioning deficits extend our earlier findings of impaired EBC in 5-year-olds to school-age. Alcohol-related impairment in the cerebellar circuitry required for both forms of conditioning may be sufficient to account for the deficit in both tasks. Extended training was beneficial for some exposed children. EBC provides a well-characterized model system for assessment of degree of cerebellar-related learning and memory dysfunction in fetal alcohol exposed children. Copyright © 2010 by the Research Society on Alcoholism.

Impaired delay and trace eyeblink conditioning in school-age children with fetal alcohol syndrome

PubMed Central

Jacobson, Sandra W.; Stanton, Mark E.; Dodge, Neil C.; Pienaar, Mariska; Fuller, Douglas S.; Molteno, Christopher D.; Meintjes, Ernesta M.; Hoyme, H. Eugene; Robinson, Luther K.; Khaole, Nathaniel; Jacobson, Joseph L.

2013-01-01

Background Classical eyeblink conditioning (EBC) involves contingent temporal pairing of a conditioned stimulus (e.g., tone) with an unconditioned stimulus (e.g., air puff). Impairment of EBC has been demonstrated in studies of alcohol-exposed animals and in children exposed prenatally at heavy levels. Methods Fetal alcohol syndrome (FAS) was diagnosed by expert dysmorphologists in a large sample of Cape Coloured, South African children. Delay EBC was examined in a new sample of 63 children at 11.3 years, and trace conditioning in 32 of the same children at 12.8 years. At each age, two sessions of 50 trials each were administered on the same day; two more sessions the next day, for children not meeting criterion for conditioning. Results 6 of 34 (17.6%) children born to heavy drinkers were diagnosed with FAS, 28 were heavily exposed nonsyndromal (HE), and 29 were non-exposed controls. Only 33.3% with FAS and 42.9% of HE met criterion for delay conditioning, compared with 79.3% of controls. The more difficult trace conditioning task was also highly sensitive to fetal alcohol exposure. Only 16.7% of the FAS and 21.4% of HE met criterion for trace conditioning, compared with 66.7% of controls. The magnitude of the effect of diagnostic group on trace conditioning was not greater than the effect on short delay conditioning, findings consistent with recent rat studies. Longer latency to onset and peak eyeblink CR in exposed children indicated poor timing and failure to blink in anticipation of the puff. Extended training resulted in some but not all of the children reaching criterion. Conclusions These data showing alcohol-related delay and trace conditioning deficits extend our earlier findings of impaired EBC in 5-year-olds to school-age. Alcohol-related impairment in the cerebellar circuitry required for both forms of conditioning may be sufficient to account for the deficit in both tasks. Extended training was beneficial for some exposed children. EBC provides a well-characterized model system for assessment of degree of cerebellar-related learning and memory dysfunction in fetal alcohol exposed children. PMID:21073484

Experimental study of heat and mass transfer in a buoyant countercurrent exchange flow

NASA Astrophysics Data System (ADS)

Conover, Timothy Allan

Buoyant Countercurrent Exchange Flow occurs in a vertical vent through which two miscible fluids communicate, the higher-density fluid, residing above the lower-density fluid, separated by the vented partition. The buoyancy- driven zero net volumetric flow through the vent transports any passive scalars, such as heat and toxic fumes, between the two compartments as the fluids seek thermodynamic and gravitational equilibrium. The plume rising from the vent into the top compartment resembles a pool fire plume. In some circumstances both countercurrent flows and pool fires can ``puff'' periodically, with distinct frequencies. One experimental test section containing fresh water in the top compartment and brine (NaCl solution) in the bottom compartment provided a convenient, idealized flow for study. This brine flow decayed in time as the concentrations approached equilibrium. A second test section contained fresh water that was cooled by heat exchangers above and heated by electrical elements below and operated steadily, allowing more time for data acquisition. Brine transport was reduced to a buoyancy- scaled flow coefficient, Q*, and heat transfer was reduced to an analogous coefficient, H*. Results for vent diameter D = 5.08 cm were consistent between test sections and with the literature. Some results for D = 2.54 cm were inconsistent, suggesting viscosity and/or molecular diffusion of heat become important at smaller scales. Laser Doppler Velocimetry was used to measure velocity fields in both test sections, and in thermal flow a small thermocouple measured temperature simultaneously with velocity. Measurement fields were restricted to the plume base region, above the vent proper. In baseline periodic flow, instantaneous velocity and temperature were ensemble averaged, producing a movie of the average variation of each measure during a puffing flow cycle. The temperature movie revealed the previously unknown cold core of the puff during its early development. The renewal-length model for puffing frequency of pool fire plumes was extended to puffing countercurrent flows by estimating inflow dilution. Puffing frequencies at several conditions were reduced to Strouhal number based on dilute plume density. Results for D = 5.08 cm compared favorably to published measurements of puffing pool fires, suggesting that the two different flows obey the same periodic dynamic process.

Investigation of magnetic flux transport and shock formation in a staged Z-pinch

NASA Astrophysics Data System (ADS)

Narkis, J.; Rahman, H. U.; Wessel, F. J.; Beg, F. N.

2017-10-01

Target preheating is an integral component of magnetized inertial fusion in reducing convergence ratio. In the staged Z-pinch concept, it is achieved via one or more shocks. Previous work [Narkis et al., Phys. Plasmas 23, 122706 (2016)] found that shock formation in the target occurred earlier in higher-Z liners due to faster flux transport to the target/liner interface. However, a corresponding increase in magnitude of magnetic pressure was not observed, and target implosion velocity (and therefore shock strength) remained unchanged. To investigate other means of increasing the magnitude of transported flux, a Korteweg-de Vries-Burgers equation from the 1-D single-fluid, resistive magnetohydrodynamic equations is obtained. Solutions to the nondispersive (i.e., Burgers) equation depend on nondimensional coefficients, whose dependence on liner density, temperature, etc., suggests an increase in target implosion velocity, and therefore shock strength, can be obtained by tailoring the mass of a single-liner gas puff to a double-liner configuration. In the selected test cases of 1-D simulated implosions of krypton on deuterium, the peak Mach number increased from ˜ 5 to ˜ 8 . While a notable increase was seen, Mach numbers exceeding 10 (implosion velocities exceeding ˜25 cm/μs) are necessary for adequate shock preheating.

Mapping multisensory parietal face and body areas in humans.

PubMed

Huang, Ruey-Song; Chen, Ching-fu; Tran, Alyssa T; Holstein, Katie L; Sereno, Martin I

2012-10-30

Detection and avoidance of impending obstacles is crucial to preventing head and body injuries in daily life. To safely avoid obstacles, locations of objects approaching the body surface are usually detected via the visual system and then used by the motor system to guide defensive movements. Mediating between visual input and motor output, the posterior parietal cortex plays an important role in integrating multisensory information in peripersonal space. We used functional MRI to map parietal areas that see and feel multisensory stimuli near or on the face and body. Tactile experiments using full-body air-puff stimulation suits revealed somatotopic areas of the face and multiple body parts forming a higher-level homunculus in the superior posterior parietal cortex. Visual experiments using wide-field looming stimuli revealed retinotopic maps that overlap with the parietal face and body areas in the postcentral sulcus at the most anterior border of the dorsal visual pathway. Starting at the parietal face area and moving medially and posteriorly into the lower-body areas, the median of visual polar-angle representations in these somatotopic areas gradually shifts from near the horizontal meridian into the lower visual field. These results suggest the parietal face and body areas fuse multisensory information in peripersonal space to guard an individual from head to toe.

Staged Z-pinch experiments on the Mega-Ampere current driver COBRA

NASA Astrophysics Data System (ADS)

Valenzuela, Julio; Banasek, Jacob; Byvank, Thomas; Conti, Fabio; Greenly, John; Hammer, David; Potter, William; Rocco, Sophia; Ross, Michael; Wessel, Frank; Narkis, Jeff; Rahman, Hafiz; Ruskov, Emil; Beg, Farhat

2017-10-01

Experiments were conducted on the Cornell's 1 MA, 100 ns current driver COBRA with the goal of better understanding the Staged Z-pinch physics and validating MHD codes. We used a gas injector composed of an annular (1.2 cm radius) high atomic number (e.g., Ar or Kr) gas-puff and an on-axis plasma gun that delivers the ionized hydrogen target. Liner implosion velocity and stability were studied using laser shadowgraphy and interferometry as well as XUV imaging. From the data, the signature of the MRT instability and zippering effect can be seen, but time integrated X-ray imaging show a stable target plasma. A key component of the experiment was the use of optical Thomson scattering (TS) diagnostics to characterize the liner and target plasmas. By fitting the experimental scattered spectra with synthetic data, electron and ion temperature as well as density can be obtained. Preliminary analysis shows significant scattered line broadening from the plasma on-axis ( 0.5 mm diameter) which can be explained by either a low temperature H plasma with Te =Ti =75eV, or by a hot plasma with Ti =3keV, Te =350eV if an Ar-H mixture is present with an Ar fraction higher than 10%. Funded by the Advanced Research Projects Agency - Energy, DE-AR0000569.

Method to measure efficiently rare fluctuations of turbulence intensity for turbulent-laminar transitions in pipe flows

NASA Astrophysics Data System (ADS)

Nemoto, Takahiro; Alexakis, Alexandros

2018-02-01

The fluctuations of turbulence intensity in a pipe flow around the critical Reynolds number is difficult to study but important because they are related to turbulent-laminar transitions. We here propose a rare-event sampling method to study such fluctuations in order to measure the time scale of the transition efficiently. The method is composed of two parts: (i) the measurement of typical fluctuations (the bulk part of an accumulative probability function) and (ii) the measurement of rare fluctuations (the tail part of the probability function) by employing dynamics where a feedback control of the Reynolds number is implemented. We apply this method to a chaotic model of turbulent puffs proposed by Barkley and confirm that the time scale of turbulence decay increases super exponentially even for high Reynolds numbers up to Re =2500 , where getting enough statistics by brute-force calculations is difficult. The method uses a simple procedure of changing Reynolds number that can be applied even to experiments.

Dexpanthenol pastille and benzydamine hydrochloride spray for the prevention of post-operative sore throat.

PubMed

Gulhas, N; Canpolat, H; Cicek, M; Yologlu, S; Togal, T; Durmus, M; Ozcan Ersoy, M

2007-02-01

In this study, we aimed to compare the effectiveness of dexpanthenol pastille and benzydamine hydrochloride spray on the prevention of a sore throat. One hundred and eighty patients undergoing general anaesthesia, who were ASA I-II and with their ages ranging between 15 and 70 years, were randomly allocated to three groups, each consisting of 60 patients. For group B, four puffs of benzydamine hydrochloride were sprayed into the mouth initially 30 min before the operation and repeatedly 5 min before anaesthesia induction. For group D, two pastilles of dexpanthenol were administered orally to be sucked 30 min before the operation. For group P, four puffs of distilled water were sprayed into the mouth initially 30 min before the operation. Post-operatively, patients were evaluated for a sore throat for the duration of 24 h. The incidence of a sore throat was significantly lower for group D when compared with group B and group P. The incidence of a sore throat was similar for group B and group P. According to the sore throat grading system, the number of patients experiencing no complaints was significantly higher for group D when compared with group B and group P. The number of patients achieving moderate scores was significantly higher for group B when compared with group D. The administration of 200 mg of dexpanthenol prophylactically before endotracheal intubation is effective in the prevention of post-operative sore throat.

Turbulent particle transport as a function of toroidal rotation in DIII-D H-mode plasmas

DOE PAGES

Wang, Xin; Mordijck, Saskia; Zeng, Lei; ...

2016-03-01

In this paper we show how changes in toroidal rotation, by controlling the injected torque, affect particle transport and confinement. The toroidal rotation is altered using the co- and counter neutral beam injection (NBI) in low collisionality H-mode plasmas on DIII-D with dominant electron cyclotron heating (ECH). We find that there is no correlation between the toroidal rotation shear and the inverse density gradient, which is observed on AUG whenmore » $${{T}_{\\text{e}}}/{{T}_{\\text{i}}}$$ is varied using ECH (Angioni et al 2011 Phys. Rev. Lett. 107 215003). In DIII-D, we find that in a discharge with balanced torque injection, the $$E\\times B$$ shear is smaller than the linear gyrokinetic growth rate for small $${{k}_{\\theta}}{{\\rho}_{s}}$$ for $$\\rho =0.6$$ –0.85. This results in lower particle confinement. In the co- and counter- injected discharges the $$E\\times B$$ shear is larger or close to the linear growth rate at the plasma edge and both configurations have higher particle confinement. In order to measure particle transport, we use a small periodic perturbative gas puff. This gas puff perturbs the density profiles and allows us to extract the perturbed diffusion and inward pinch coefficients. We observe a strong increase in the inward particle pinch in the counter-torque injected plasma. Lastly, the calculated quasi-linear particle flux, nor the linear growth rates using TGLF agree with experimental observations.« less

Increasing the Value of an Alternative Monetary Reinforcer Reduces Cigarette Choice in Adolescents

PubMed Central

Tidey, Jennifer W.; Kahler, Christopher W.; Wray, Tyler B.; Colby, Suzanne M.

2015-01-01

Introduction: Smoking can be conceptualized as an operant behavior maintained by the reinforcing effects of cigarettes. Changing the magnitude and availability of alternative reinforcers should shift behavior away from smoking. Adults’ smoking behavior is sensitive to the magnitude and availability of alternative reinforcers; however, the extent to which the same is true for adolescents has not yet been shown in the laboratory. Methods: To test the sensitivity of adolescent smoking behavior to changes in the magnitude of alternative reinforcement, we gave adolescents who abstained overnight the opportunity to make 20 choices between receiving two puffs of their usual-brand cigarette or money. The magnitude of the monetary reinforcer was varied across sessions in counterbalanced order ($0.00, $0.10, and $0.50). Results: Results indicated that adolescents’ choices for puffs decreased as a function of increasing monetary reinforcer magnitude, while money choices increased. This effect was moderated by baseline smoking level and by gender, such that heavier-smoking participants and males made more cigarette choices when the alternative monetary value was zero, and decreased their choices more steeply in response to increasing monetary value. Conclusions: The current study validates a laboratory choice procedure for studying smoking in adolescents, and demonstrates that adolescent smoking behavior is sensitive to changes in the magnitude of concurrently available monetary reinforcers. The current paradigm can be adapted and applied to explore the effects of other variables that may affect cigarette choice in adolescents. PMID:25666814

Preventing airborne infection with an intranasal cellulose powder formulation (Nasaleze travel).

PubMed

Hiltunen, Raimo; Josling, Peter D; James, Mike H

2007-01-01

A total of 52 volunteers were recruited to take part in a dual-centered, randomized, blinded study so investigators could determine whether the level of airborne infection could be significantly reduced in patients randomly assigned to treatment with either Nasaleze cellulose extract alone or a combination of Nasaleze cellulose and powdered garlic extract (PGE). One puff into each nostril was recommended, and volunteers who developed an infection while traveling were told to use at least 3 puffs per nostril until symptoms were reduced. This study took place over an 8-wk period across Finland and the United Kingdom between November 2006 and March 2007. Volunteers were instructed to use a 5-point scale to assess their health and to record infectious episodes and symptoms in a daily diary. The activetreatment group (Nasaleze cellulose with PGE) experienced significantly fewer infections than the control group (20 vs 57; P<.001) and far fewer days on which an infection was obviously present (126 d in the active group vs 240 d in the control group; P<.05). Consequently, volunteers in the active group were less likely to pick up an airborne infection when PGE was added to this novel cellulose extract. Volunteers in the control group were much more likely to report more than 1 infectious episode over the treatment period or to endure longer periods of infection. The investigators concluded that the combination Nasaleze Travel formulation significantly reduced the number of airborne infections to which volunteers were exposed while traveling.

Influence of cigarette circumference on smoke chemistry, biological activity, and smoking behaviour.

PubMed

McAdam, Kevin; Eldridge, Alison; Fearon, Ian M; Liu, Chuan; Manson, Andrew; Murphy, James; Porter, Andrew

2016-12-01

Cigarettes with reduced circumference are increasingly popular in some countries, hence it is important to understand the effects of circumference reduction on their burning behaviour, smoke chemistry and bioactivity. Reducing circumference reduces tobacco mass burn rate, puff count and static burn time, and increases draw resistance and rod length burned during puff and smoulder periods. Smoulder temperature increases with decreasing circumference, but with no discernible effect on cigarette ignition propensity during a standard test. At constant packing density, mainstream (MS) and sidestream (SS) tar and nicotine yields decrease approximately linearly with decreasing circumference, as do the majority of smoke toxicants. However, volatile aldehydes, particularly formaldehyde, show a distinctly non-linear relationship with circumference and increases in the ratios of aldehydes to tar and nicotine have been observed as the circumference decreases. Mutagenic, cytotoxic and tumorigenic specific activities of smoke condensates (i.e. per unit weight of condensate) decrease as circumference decreases. Recent studies suggest that there is no statistical difference in mouth-level exposure to tar and nicotine among smokers of cigarettes with different circumferences. Commercially available slim cigarettes usually have changes in other cigarette design features compared with cigarettes with standard circumference, so it is difficult to isolate the effect of circumference on the properties of commercial products. However, available data shows that changes in cigarette circumference offer no discernible change to the harm associated with smoking. Crown Copyright © 2016. Published by Elsevier Inc. All rights reserved.

Smoked marijuana effects on tobacco cigarette smoking behavior.

PubMed

Kelly, T H; Foltin, R W; Rose, A J; Fischman, M W; Brady, J V

1990-03-01

The effects of marijuana smoke exposure on several measures of tobacco cigarette smoking behavior were examined. Eight healthy adult male volunteers, who smoked both tobacco and marijuana cigarettes, participated in residential studies, lasting 10 to 15 days, designed to measure the effects of marijuana smoke exposure on a range of behavioral variables. Tobacco cigarettes were available throughout the day (9:00 A.M. until midnight). Each day was divided into a private period (9:00 A.M. to 5:00 P.M.), during which subjects were socially isolated, and a social period (5:00 P.M. to midnight), during which subjects could interact. Under blind conditions, subjects smoked placebo and active marijuana cigarettes (0%, 1.3%, 2.3%, or 2.7% delta 9-tetrahydrocannabinol) four times daily (9:45 A.M., 1:30 P.M., 5:00 P.M. and 8:30 P.M.). Each subject was exposed to both placebo and one active dose over 2- to 5-consecutive-day intervals, and dose conditions (i.e., placebo or active) alternated throughout the study. Active marijuana smoking significantly decreased the number of daily tobacco smoking bouts, increased inter-bout intervals and decreased inter-puff intervals. Marijuana decreased the number of tobacco smoking bouts by delaying the initiation of tobacco cigarette smoking immediately after marijuana smoking, whereas decreases in inter-puff intervals were unrelated to the time of marijuana smoking. No consistent interactions between marijuana effects and social or private periods (i.e., time of day) were observed.

Quantitative assessment of responses of the eyeball based on data from the Corvis tonometer.

PubMed

Koprowski, Robert; Wilczyński, Sławomir; Nowinska, Anna; Lyssek-Boron, Anita; Teper, Sławomir; Wylegala, Edward; Wróbel, Zygmunt

2015-03-01

The "air-puff" tonometers, include the Corvis, are a type of device for measuring intraocular pressure and biomechanics parameters. The paper attempts to analyse this response and its relationship with other parameters measured in the Corvis tonometer. A number of 13,400 2D images were acquired from the Corvis device and analysed (32 healthy and 16 ill people). A new method has been proposed for the analysis of responses of the eyeball based on morphological transformations and contextual operations. The proposed algorithm enables to determine responses of the eyeball to an air puff coming from the Corvis tonometer. Additionally, responses of the eyeball have been linked to some selected features of corneal deformation. The results include, among others: (1) distinguishability between the left and right eye with an error of 7%; (2) the correlation between the area under the curve in corneal deformation and the response of the eyeball -0.26; (3) the correlation between the highest concavity time and the maximum deformation amplitude of 0.4. All these features are obtained fully automatically and repetitively at a time of 3.8s per patient (Core i7 10GB RAM). It is possible to measure additional parameters of the eye deformation which are not available in the original software of the Corvis tonometer. The use of the proposed methods of image analysis and processing provides results directly from the eye response measurement when measuring intraocular pressure. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Late-Time Formation and Dynamical Signatures of Small Planets

NASA Astrophysics Data System (ADS)

Lee, Eve Jihyun

The riddle posed by super-Earths is that they are not Jupiters: their core masses are large enough to trigger runaway gas accretion, yet somehow super-Earths accreted atmospheres that weigh only a few percent of their total mass. In this thesis, I demonstrate that this puzzle is solved if super-Earths formed late, in the inner cavities of transitional disks. Super-puffs present the inverse problem of being too voluminous for their small masses. I show that super-puffs most easily acquire their thick atmospheres as dust-free, rapidly cooling worlds outside 1 AU, and then migrate in just after super-Earths appear. Super-Earths and Earth-sized planets around FGKM dwarfs are evenly distributed in log orbital period down to 10 days, but dwindle in number at shorter periods. I demonstrate that both the break at 10 days and the slope of the occurrence rate down to 1 day can be reproduced if planets form in disks that are truncated by their host star magnetospheres at co-rotation. Planets can be brought from disk edges to ultra-short (<1 day) periods by asynchronous equilibrium tides raised on their stars. Small planets may remain ubiquitous out to large orbital distances. I demonstrate that the variety of debris disk morphologies revealed by scattered light images can be explained by viewing an eccentric disk, secularly forced by a planet of just a few Earth masses, from different observing angles. The farthest reaches of planetary systems may be perturbed by eccentric super-Earths.

Carbonyl Emissions in E-cigarette Aerosol: A Systematic Review and Methodological Considerations.

PubMed

Farsalinos, Konstantinos E; Gillman, Gene

2017-01-01

Carbonyl emissions from tobacco cigarettes represent a substantial health risk contributing to smoking-related morbidity and mortality. As expected, this is an important research topic for tobacco harm reduction products, in an attempt to compare the relative risk of these products compared to tobacco cigarettes. In this study, a systematic review of the literature available on PubMed was performed analyzing the studies evaluating carbonyl emissions from e-cigarettes. A total of 32 studies were identified and presented. We identified a large diversity of methodologies, with substantial discrepancies in puffing patterns, aerosol collection and analytical methods as well as reported units of measurements. Such discrepancies make comparisons difficult, and in some cases the accuracy of the findings cannot be determined. Importantly, control for the generation of dry puffs was not performed in the vast majority of studies, particularly in studies using variable power devices, which could result in testing conditions and reported carbonyl levels that have no clinical relevance or context. Some studies have been replicated, verifying the presence of dry puff conditions. Whenever realistic use conditions were ensured, carbonyl emissions from e-cigarettes were substantially lower than tobacco cigarette smoke, while newer generation (bottom-coil, cotton wick) atomizers appeared to emit minimal levels of carbonyls with questionable clinical significance in terms of health risk. However, extremely high levels of carbonyl emissions were reported in some studies, and all these studies need to be replicated because of potentially important health implications.

The effect of palm oil, lard, and puff-pastry margarine on postprandial lipid and hormone responses in normal-weight and obese young women.

PubMed

Jensen, J; Bysted, A; Dawids, S; Hermansen, K; Hølmer, G

1999-12-01

Only a few studies have been published on the postprandial effects of different fatty acids in obese subjects. Therefore, the present study investigated the effects of three test meals containing palm oil (PO), lard (LD), or puff-pastry margarine (PPM), all normal dietary ingredients, on postprandial lipid and hormone responses in normal-weight and obese young women. The study was performed as a randomized, crossover design. The fats differed in the content of palmitic acid, stearic acid, and trans monounsaturated fatty acids allowing a dietary comparison of different 'solid' fatty acids. The obese women had significantly higher fasting concentrations and postprandial responses of plasma total triacylglycerol (TAG), chylomicron-TAG, and insulin compared with the normal-weight women but there was no significant difference in the postprandial responses between the three test meals. The obese women had fasting concentrations of leptin four times greater than the normal-weight women. There were no postprandial changes in the concentrations of leptin. The fasting concentrations of HDL-cholesterol were significantly lower in the obese women than in the normal-weight women, whereas there was no significant difference between the two groups in the concentrations of total cholesterol or LDL-cholesterol. These results provide evidence that obese women have exaggerated lipid and hormone responses compared with normal-weight women but the different contents of saturated and trans monounsaturated fatty acids provided by PO, LD, and PPM have no effect in either group.

Gamma-ray imaging assay of cells 3-5 of the east cell line in the 235-F plutonium fuel form facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brand, A. D.; Aucott, T. J.; Diprete, D. P.

In August and September, 2016, scientists from the Savannah River National Laboratory (SRNL) took a series of gamma-ray imaging measurements through the cell windows in front of Cells 3-5 on the east line of the Plutonium Fuel Form (PuFF) Facility using an electrically cooled, high-purity germanium detector. A Germanium Gamma Ray Imager (GeGI) was utilized since it allowed for the location from which the radiation was being emitted to be identified by incoming gamma-ray energy. This measurement technique provided a tool which allowed for the relative concentration of Pu-238 to be mapped throughout each cell. The mapping and new assaymore » data were then used to update the model used in an assay discussed in a 2014 report (SRNL-STI-2014-00629) and to calculate a more accurate value for the holdup in each of the cells [1]. Note that the mapping and new assay data did not replace the previous assay data in the model. Rather, the mapping and new assay data provided additional details on source distribution, which supplemented the previous assay data.« less

Development of a spectroscopic technique for simultaneous magnetic field, electron density, and temperature measurements in ICF-relevant plasmas.

PubMed

Dutra, E C; Koch, J A; Presura, R; Angermeier, W A; Darling, T; Haque, S; Mancini, R C; Covington, A M

2016-11-01

Spectroscopic techniques in the visible range are often used in plasma experiments to measure B-field induced Zeeman splitting, electron densities via Stark broadening, and temperatures from Doppler broadening. However, when electron densities and temperatures are sufficiently high, the broadening of the Stark and Doppler components can dominate the emission spectra and obscure the Zeeman component. In this research, we are developing a time-resolved multi-axial technique for measuring the Zeeman, Stark, and Doppler broadened line emission of dense magnetized plasmas for Z-pinch and Dense Plasma Focus (DPF) accelerators. The line emission is used to calculate the electron densities, temperatures, and B-fields. In parallel, we are developing a line-shape modeling code that incorporates the broadening effects due to Stark, Doppler, and Zeeman effects for dense magnetized plasma. This manuscript presents the details of the experimental setup and line shape code, along with the results obtained from an Al iii doublet at the University of Nevada, Reno at Nevada Terawatt Facility. Future tests are planned to further evaluate the technique and modeling on other material wire array, gas puff, and DPF platforms.

Peptides from puff adder Bitis arietans venom, novel inhibitors of nicotinic acetylcholine receptors.

PubMed

Vulfius, Catherine A; Spirova, Ekaterina N; Serebryakova, Marina V; Shelukhina, Irina V; Kudryavtsev, Denis S; Kryukova, Elena V; Starkov, Vladislav G; Kopylova, Nina V; Zhmak, Maxim N; Ivanov, Igor A; Kudryashova, Ksenia S; Andreeva, Tatyana V; Tsetlin, Victor I; Utkin, Yuri N

2016-10-01

Phospholipase A 2 (named bitanarin) possessing capability to block nicotinic acetylcholine receptors (nAChRs) was isolated earlier (Vulfius et al., 2011) from puff adder Bitis arietans venom. Further studies indicated that low molecular weight fractions of puff adder venom inhibit nAChRs as well. In this paper, we report on isolation from this venom and characterization of three novel peptides called baptides 1, 2 and 3 that reversibly block nAChRs. To isolate the peptides, the venom of B. arietans was fractionated by gel-filtration and reversed phase chromatography. The amino acid sequences of peptides were established by de novo sequencing using MALDI mass spectrometry. Baptide 1 comprised 7, baptides 2 and 3-10 amino acid residues, the latter being acetylated at the N-terminus. This is the first indication for the presence of such post-translational modification in snake venom proteins. None of the peptides contain cysteine residues. For biological activity studies the peptides were prepared by solid phase peptide synthesis. Baptide 3 and 2 blocked acetylcholine-elicited currents in isolated Lymnaea stagnalis neurons with IC 50 of about 50 μM and 250 μM, respectively. In addition baptide 2 blocked acetylcholine-induced currents in muscle nAChR heterologously expressed in Xenopus oocytes with IC 50 of about 3 μM. The peptides did not compete with radioactive α-bungarotoxin for binding to Torpedo and α7 nAChRs at concentration up to 200 μM that suggests non-competitive mode of inhibition. Calcium imaging studies on α7 and muscle nAChRs heterologously expressed in mouse neuroblastoma Neuro2a cells showed that on α7 receptor baptide 2 inhibited acetylcholine-induced increasing intracellular calcium concentration with IC 50 of 20.6 ± 3.93 μM. On both α7 and muscle nAChRs the suppression of maximal response to acetylcholine by about 50% was observed at baptide 2 concentration of 25 μM, the value being close to IC 50 on α7 nAChR. These data are in accord with non-competitive inhibition as follows from α-bungarotoxin binding experiments. The described peptides are the shortest peptides without disulfide bridges isolated from animal venom and capable to inhibit nAChR by non-competitive way. Copyright © 2016. Published by Elsevier Ltd.

CaMKII Regulates Synaptic NMDA Receptor Activity of Hypothalamic Presympathetic Neurons and Sympathetic Outflow in Hypertension.

PubMed

Li, De-Pei; Zhou, Jing-Jing; Zhang, Jixiang; Pan, Hui-Lin

2017-11-01

NMDAR activity in the hypothalamic paraventricular nucleus (PVN) is increased and critically involved in heightened sympathetic vasomotor tone in hypertension. Calcium/calmodulin-dependent protein kinase II (CaMKII) binds to and modulates NMDAR activity. In this study, we determined the role of CaMKII in regulating NMDAR activity of PVN presympathetic neurons in male spontaneously hypertensive rats (SHRs). NMDAR-mediated EPSCs and puff NMDA-elicited currents were recorded in spinally projecting PVN neurons in SHRs and male Wistar-Kyoto (WKY) rats. The basal amplitude of evoked NMDAR-EPSCs and puff NMDA currents in retrogradely labeled PVN neurons were significantly higher in SHRs than in WKY rats. The CaMKII inhibitor autocamtide-2-related inhibitory peptide (AIP) normalized the increased amplitude of NMDAR-EPSCs and puff NMDA currents in labeled PVN neurons in SHRs but had no effect in WKY rats. Treatment with AIP also normalized the higher frequency of NMDAR-mediated miniature EPSCs of PVN neurons in SHRs. CaMKII-mediated phosphorylation level of GluN2B serine 1303 (S1303) in the PVN, but not in the hippocampus and frontal cortex, was significantly higher in SHRs than in WKY rats. Lowering blood pressure with celiac ganglionectomy in SHRs did not alter the increased level of phosphorylated GluN2B S1303 in the PVN. In addition, microinjection of AIP into the PVN significantly reduced arterial blood pressure and lumbar sympathetic nerve discharges in SHRs. Our findings suggest that CaMKII activity is increased in the PVN and contributes to potentiated presynaptic and postsynaptic NMDAR activity to elevate sympathetic vasomotor tone in hypertension. SIGNIFICANCE STATEMENT Heightened sympathetic vasomotor tone is a major contributor to the development of hypertension. Although glutamate NMDA receptor (NMDAR)-mediated excitatory drive in the hypothalamus plays a critical role in increased sympathetic output in hypertension, the molecular mechanism involved in potentiated NMDAR activity of hypothalamic presympathetic neurons remains unclear. Here we show that the activity of calcium/calmodulin-dependent protein kinase II (CaMKII) is increased and plays a key role in the potentiated presynaptic and postsynaptic NMDAR activity of hypothalamic presympathetic neurons in hypertension. Also, the inhibition of CaMKII in the hypothalamus reduces elevated blood pressure and sympathetic nerve discharges in hypertension. This new knowledge extends our understanding of the mechanism of synaptic plasticity in the hypothalamus and suggests new strategies to treat neurogenic hypertension. Copyright © 2017 the authors 0270-6474/17/3710690-10$15.00/0.

Have combustible cigarettes met their match? The nicotine delivery profiles and harmful constituent exposures of second-generation and third-generation electronic cigarette users.

PubMed

Wagener, Theodore L; Floyd, Evan L; Stepanov, Irina; Driskill, Leslie M; Frank, Summer G; Meier, Ellen; Leavens, Eleanor L; Tackett, Alayna P; Molina, Neil; Queimado, Lurdes

2017-03-01

Electronic cigarettes' (e-cigarettes) viability as a public health strategy to end smoking will likely be determined by their ability to mimic the pharmacokinetic profile of a cigarette while also exposing users to significantly lower levels of harmful/potentially harmful constituents (HPHCs). The present study examined the nicotine delivery profile of third- (G3) versus second-generation (G2) e-cigarette devices and their users' exposure to nicotine and select HPHCs compared with cigarette smokers. 30 participants (10 smokers, 9 G2 and 11 G3 users) completed baseline questionnaires and provided exhaled carbon monoxide (eCO), saliva and urine samples. Following a 12-hour nicotine abstinence, G2 and G3 users completed a 2-hour vaping session (ie, 5 min, 10-puff bout followed by ad libitum puffing for 115 min). Blood samples, subjective effects, device characteristics and e-liquid consumption were assessed. Smokers, G2 and G3 users had similar baseline levels of cotinine, but smokers had 4 and 7 times higher levels of eCO (p<0.0001) and total 4-(Methylnitrosamino)-1-(3-pyridyl)-1-butanol (i.e., NNAL, p<0.01), respectively, than G2 or G3 users. Compared with G2s, G3 devices delivered significantly higher power to the atomiser, but G3 users vaped e-cigarette liquids with significantly lower nicotine concentrations. During the vaping session, G3 users achieved significantly higher plasma nicotine concentrations than G2 users following the first 10 puffs (17.5 vs 7.3 ng/mL, respectively) and at 25 and 40 min of ad libitum use. G3 users consumed significantly more e-liquid than G2 users. Vaping urges/withdrawal were reduced following 10 puffs, with no significant differences between device groups. Under normal use conditions, both G2 and G3 devices deliver cigarette-like amounts of nicotine, but G3 devices matched the amount and speed of nicotine delivery of a conventional cigarette. Compared with cigarettes, G2 and G3 e-cigarettes resulted in significantly lower levels of exposure to a potent lung carcinogen and cardiovascular toxicant. These findings have significant implications for understanding the addiction potential of these devices and their viability/suitability as aids to smoking cessation. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Calcium waves in a grid of clustered channels with synchronous IP3 binding and unbinding.

PubMed

Rückl, M; Rüdiger, S

2016-11-01

Calcium signals in cells occur at multiple spatial scales and variable temporal duration. However, a physical explanation for transitions between long-lasting global oscillations and localized short-term elevations (puffs) of cytoplasmic Ca 2+ is still lacking. Here we introduce a phenomenological, coarse-grained model for the calcium variable, which is represented by ordinary differential equations. Due to its small number of parameters, and its simplicity, this model allows us to numerically study the interplay of multi-scale calcium concentrations with stochastic ion channel gating dynamics even in larger systems. We apply this model to a single cluster of inositol trisphosphate (IP 3 ) receptor channels and find further evidence for the results presented in earlier work: a single cluster may be capable of producing different calcium release types, where long-lasting events are accompanied by unbinding of IP 3 from the receptor (Rückl et al., PLoS Comput. Biol. 11, e1003965 (2015)). Finally, we show the practicability of the model in a grid of 64 clusters which is computationally intractable with previous high-resolution models. Here long-lasting events can lead to synchronized oscillations and waves, while short events stay localized. The frequency of calcium releases as well as their coherence can thereby be regulated by the amplitude of IP 3 stimulation. Finally the model allows for a new explanation of oscillating [IP 3 ], which is not based on metabolic production and degradation of IP 3 .

Estimating dispersion from a tornado vortex and mesocyclone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weber, A.H.; Hunter, C.H.

Atmospheric dispersion modeling is required to ensure that a postulated breach in radionuclide storage containers at the Savannah River Site (SRS) from a tornado strike of Fujita-scale intensity F2 or higher will not result in an unacceptable dose to individuals. Fujita-scale tornado descriptions are included in Appendix A of this report. Dispersion models previously used at SRS for estimating dispersion following a tornado strike were developed by D.W. Pepper in 1975 (DP-1387, Dispersion of Small Particles) and H.R. Haynes and D.W. Taylor in 1983 (DPST-82-982, Estimating Doses from Tornado Winds). Research conducted in 1983 on the formation and evolution ofmore » tornadic thunderstorms has lead to a more complete understanding of the tornado vortex and associated persistent updraft and downdraft regions within the parent thunderstorm. To ensure that appropriate, contemporary methods are used for safety analysis, the Pepper model and the Haynes and Taylor model were evaluated with respect to current knowledge of circulations within tornadic thunderstorms. Pepper`s model is complex numerically but contains most of the desired physical parameterizations. Haynes and Taylor`s model is used with the Puff-Plume model (an emergency response model on the Weather INformation and Display System at SRS) and has provisions for radionuclide deposition and rainout. Haynes and Taylor assumed heavy rain following the tornado for a period of ten minutes, followed by a lighter rain for another ten minutes, then no rain for the period when the material is transported to 100 km downwind. However, neither model incorporates the effects of a nearby thunderstorm downdraft.« less

Evolution of a new sense for wind in flying phasmids? Afferents and interneurons

NASA Astrophysics Data System (ADS)

Hustert, Reinhold; Klug, Rebecca

2009-12-01

The evolution of winged stick insects (phasmids) from secondarily wingless ancestors was proposed in recent studies. We explored the cuticle of flying phasmids for wind sensors that could be involved in their flight control, comparable to those known for locusts. Surprisingly, wind-sensitive hairs (wsH) occur on the palps of mouthparts and on the antennae of the winged phasmid Sipyloidea sipylus which can fly in tethered position only when air currents blow over the mouthparts. The present study describes the morphology and major functional properties of these “new” wsH with soft and bulging hair bases which are different from the beaker-like hair bases of the wsH on the cerci of phasmids and the wsH described in other insects. The most sensitive wsH of antennae and palps respond with phasic-tonic afferents to air currents exceeding 0.2 ms-1. The fields of wsH on one side of the animal respond mainly to ventral, lateral, and frontal wind on the ipsilateral side of the head. Afferent inputs from the wsH converge but also diverge to a group of specific interneurons at their branches in the suboesophageal ganglion and can send their integrated input from wsH fields of the palps and antennae to the thoracic central nervous system. Response types of individual wsH-interneurons are either phasic or phasic-tonic to air puffs or constant air currents and also, the receptive fields of individual interneurons differ. We conclude that the “new” wsH system and its interneurons mainly serve to maintain flight activity in airborne phasmids and also, the “new” wsH must have emerged together with the integrating interneurons during the evolution from wingless to the recent winged forms of phasmids.

Ensemble Simulations with Coupled Atmospheric Dynamic and Dispersion Models: Illustrating Uncertainties in Dosage Simulations.

NASA Astrophysics Data System (ADS)

Warner, Thomas T.; Sheu, Rong-Shyang; Bowers, James F.; Sykes, R. Ian; Dodd, Gregory C.; Henn, Douglas S.

2002-05-01

Ensemble simulations made using a coupled atmospheric dynamic model and a probabilistic Lagrangian puff dispersion model were employed in a forensic analysis of the transport and dispersion of a toxic gas that may have been released near Al Muthanna, Iraq, during the Gulf War. The ensemble study had two objectives, the first of which was to determine the sensitivity of the calculated dosage fields to the choices that must be made about the configuration of the atmospheric dynamic model. In this test, various choices were used for model physics representations and for the large-scale analyses that were used to construct the model initial and boundary conditions. The second study objective was to examine the dispersion model's ability to use ensemble inputs to predict dosage probability distributions. Here, the dispersion model was used with the ensemble mean fields from the individual atmospheric dynamic model runs, including the variability in the individual wind fields, to generate dosage probabilities. These are compared with the explicit dosage probabilities derived from the individual runs of the coupled modeling system. The results demonstrate that the specific choices made about the dynamic-model configuration and the large-scale analyses can have a large impact on the simulated dosages. For example, the area near the source that is exposed to a selected dosage threshold varies by up to a factor of 4 among members of the ensemble. The agreement between the explicit and ensemble dosage probabilities is relatively good for both low and high dosage levels. Although only one ensemble was considered in this study, the encouraging results suggest that a probabilistic dispersion model may be of value in quantifying the effects of uncertainties in a dynamic-model ensemble on dispersion model predictions of atmospheric transport and dispersion.

Modeling of the dispersion of depleted uranium aerosol.

PubMed

Mitsakou, C; Eleftheriadis, K; Housiadas, C; Lazaridis, M

2003-04-01

Depleted uranium is a low-cost radioactive material that, in addition to other applications, is used by the military in kinetic energy weapons against armored vehicles. During the Gulf and Balkan conflicts concern has been raised about the potential health hazards arising from the toxic and radioactive material released. The aerosol produced during impact and combustion of depleted uranium munitions can potentially contaminate wide areas around the impact sites or can be inhaled by civilians and military personnel. Attempts to estimate the extent and magnitude of the dispersion were until now performed by complex modeling tools employing unclear assumptions and input parameters of high uncertainty. An analytical puff model accommodating diffusion with simultaneous deposition is developed, which can provide a reasonable estimation of the dispersion of the released depleted uranium aerosol. Furthermore, the period of the exposure for a given point downwind from the release can be estimated (as opposed to when using a plume model). The main result is that the depleted uranium mass is deposited very close to the release point. The deposition flux at a couple of kilometers from the release point is more than one order of magnitude lower than the one a few meters near the release point. The effects due to uncertainties in the key input variables are addressed. The most influential parameters are found to be atmospheric stability, height of release, and wind speed, whereas aerosol size distribution is less significant. The output from the analytical model developed was tested against the numerical model RPM-AERO. Results display satisfactory agreement between the two models.

Effect of Uruguay’s National 100% Smokefree Law on Emergency Visits for Bronchospasm

PubMed Central

Kalkhoran, Sara; Sebrié, Ernesto M; Sandoya, Edgardo; Glantz, Stanton A.

2014-01-01

Introduction Implementation of smokefree laws is followed by drops in hospital admissions for cardiovascular diseases and asthma. The impact of smokefree laws on use of non-hospital medical services has not been assessed. The purpose of this study is to evaluate the impact of Uruguay’s national 100% smokefree legislation on non-hospital emergency care visits and hospitalizations for bronchospasm and bronchodilator use. Methods The monthly number of non-hospital emergency care visits and hospitalizations for bronchospasm, as well as monthly puffs of bronchodilators (total and per person), from 3 years prior to the adoption of the 100% smokefree policy on March 1, 2006 through 5 years after the policy were assessed using interrupted time series negative binomial regression. Data analysis was conducted in 2014. Results The incidence of non-hospital emergency visits for bronchospasm decreased by 15% (incidence rate ratio [IRR]=0.85, 95% CI=0.76, 0.94) following implementation of the law. Hospitalizations for bronchospasm did not change significantly (IRR=0.89, 95% CI=0.66, 1.21). Total monthly puffs of salbutamol and ipratropium administered in the non-hospital emergency setting decreased by 224 (95% CI= −372, −76) and 179 (95% CI= −340, −18.6), respectively, from means of 1,222 and 1,007 before the law. Conclusions Uruguay’s 100% smokefree law was followed by fewer emergency visits for bronchospasm and less need for treatment, supporting adoption of such policies in low- and middle-income countries to reduce the disease burden and healthcare costs associated with smoking. PMID:25997906

Effect of Uruguay's National 100% Smokefree Law on Emergency Visits for Bronchospasm.

PubMed

Kalkhoran, Sara; Sebrié, Ernesto M; Sandoya, Edgardo; Glantz, Stanton A

2015-07-01

Implementation of smokefree laws is followed by drops in hospital admissions for cardiovascular diseases and asthma. The impact of smokefree laws on use of non-hospital medical services has not been assessed. The purpose of this study is to evaluate the impact of Uruguay's national 100% smokefree legislation on non-hospital emergency care visits, hospitalizations for bronchospasm, and bronchodilator use. The monthly number of non-hospital emergency care visits and hospitalizations for bronchospasm, as well as monthly puffs of bronchodilators (total and per person), from 3 years prior to the adoption of the 100% smokefree policy on March 1, 2006, through 5 years after the policy were assessed using interrupted time series negative binomial regression. Data analysis was conducted in 2014. The incidence of non-hospital emergency visits for bronchospasm decreased by 15% (incidence rate ratio [IRR]=0.85, 95% CI=0.76, 0.94) following implementation of the law. Hospitalizations for bronchospasm did not change significantly (IRR=0.89, 95% CI=0.66, 1.21). Total monthly puffs of salbutamol and ipratropium administered in the non-hospital emergency setting decreased by 224 (95% CI=-372, -76) and 179 (95% CI=-340, -18.6), respectively, from means of 1,222 and 1,007 before the law. Uruguay's 100% smokefree law was followed by fewer emergency visits for bronchospasm and less need for treatment, supporting adoption of such policies in low- and middle-income countries to reduce the disease burden and healthcare costs associated with smoking. Copyright © 2015 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Dynamic OCT measurement of corneal deformation by an air puff in normal and cross-linked corneas

PubMed Central

Dorronsoro, Carlos; Pascual, Daniel; Pérez-Merino, Pablo; Kling, Sabine; Marcos, Susana

2012-01-01

A new technique is presented for the non-invasive imaging of the dynamic response of the cornea to an air puff inducing a deformation. A spectral OCT instrument combined with an air tonometer in a non-collinear configuration was used to image the corneal deformation over full corneal cross-sections, as well as to obtain high speed measurements of the temporal evolution of the corneal apex. The entire deformation process can be dynamically visualized. A quantitative analysis allows direct extraction of several deformation parameters, such as amplitude, diameter and volume of the maximum deformation, as well as duration and speed of the increasing deformation period and the recovery period. The potential of the technique is demonstrated on porcine corneas in vitro under constant IOP for several conditions (untreated, after riboflavin instillation and under cross-linking with ultraviolet light), as well as on human corneas in vivo. The new technique has proved very sensitive to detect differences in the deformation parameters across conditions. We have confirmed non-invasively that Riboflavin and UV-cross-linking induce changes in the corneal biomechanical properties. Those differences appear to be the result of changes in constituent properties of the cornea, and not a consequence of changes in corneal thickness, geometry or IOP. These measurements are a first step for the estimation of the biomechanical properties of corneal tissue, at an individual level and in vivo, to improve diagnosis and prognosis of diseases and treatments involving changes in the biomechanical properties of the cornea. PMID:22435096

An fMRI-Based Neural Signature of Decisions to Smoke Cannabis.

PubMed

Bedi, Gillinder; Lindquist, Martin A; Haney, Margaret

2015-11-01

Drug dependence may be at its core a pathology of choice, defined by continued decisions to use drugs irrespective of negative consequences. Despite evidence of dysregulated decision making in addiction, little is known about the neural processes underlying the most clinically relevant decisions drug users make: decisions to use drugs. Here, we combined functional magnetic resonance imaging (fMRI), machine learning, and human laboratory drug administration to investigate neural activation underlying decisions to smoke cannabis. Nontreatment-seeking daily cannabis smokers completed an fMRI choice task, making repeated decisions to purchase or decline 1-12 placebo or active cannabis 'puffs' ($0.25-$5/puff). One randomly selected decision was implemented. If the selected choice had been bought, the cost was deducted from study earnings and the purchased cannabis smoked in the laboratory; alternatively, the participant remained in the laboratory without cannabis. Machine learning with leave-one-subject-out cross-validation identified distributed neural activation patterns discriminating decisions to buy cannabis from declined offers. A total of 21 participants were included in behavioral analyses; 17 purchased cannabis and were thus included in fMRI analyses. Purchasing varied lawfully with dose and cost. The classifier discriminated with 100% accuracy between fMRI activation patterns for purchased vs declined cannabis at the level of the individual. Dorsal striatum, insula, posterior parietal regions, anterior and posterior cingulate, and dorsolateral prefrontal cortex all contributed reliably to this neural signature of decisions to smoke cannabis. These findings provide the basis for a brain-based characterization of drug-related decision making in drug abuse, including effects of psychological and pharmacological interventions on these processes.

Imaging Local Ca2+ Signals in Cultured Mammalian Cells

PubMed Central

Lock, Jeffrey T.; Ellefsen, Kyle L.; Settle, Bret; Parker, Ian; Smith, Ian F.

2015-01-01

Cytosolic Ca2+ ions regulate numerous aspects of cellular activity in almost all cell types, controlling processes as wide-ranging as gene transcription, electrical excitability and cell proliferation. The diversity and specificity of Ca2+ signaling derives from mechanisms by which Ca2+ signals are generated to act over different time and spatial scales, ranging from cell-wide oscillations and waves occurring over the periods of minutes to local transient Ca2+ microdomains (Ca2+ puffs) lasting milliseconds. Recent advances in electron multiplied CCD (EMCCD) cameras now allow for imaging of local Ca2+ signals with a 128 x 128 pixel spatial resolution at rates of >500 frames sec-1 (fps). This approach is highly parallel and enables the simultaneous monitoring of hundreds of channels or puff sites in a single experiment. However, the vast amounts of data generated (ca. 1 Gb per min) render visual identification and analysis of local Ca2+ events impracticable. Here we describe and demonstrate the procedures for the acquisition, detection, and analysis of local IP3-mediated Ca2+ signals in intact mammalian cells loaded with Ca2+ indicators using both wide-field epi-fluorescence (WF) and total internal reflection fluorescence (TIRF) microscopy. Furthermore, we describe an algorithm developed within the open-source software environment Python that automates the identification and analysis of these local Ca2+ signals. The algorithm localizes sites of Ca2+ release with sub-pixel resolution; allows user review of data; and outputs time sequences of fluorescence ratio signals together with amplitude and kinetic data in an Excel-compatible table. PMID:25867132

A Series of Jets that Drove Streamer-Puff CMEs from Giant Active Region of 2014

NASA Technical Reports Server (NTRS)

Panesar, Navdeep K.; Sterling, Alphonse C.; Moore, Ronald L.

2016-01-01

We investigate characteristics of solar coronal jets that originated from active region NOAA 12192 and produced coronal mass ejections (CMEs). This active region produced many non­-jet major flare eruptions (X and M class) that made no CME. A multitude of jets occurred from the southeast edge of the active region, and in contrast to the major-­flare eruptions in the core, six of these jets resulted in CMEs. Our jet observations are from SDO/AIA EUV channels and from Hinode/XRT, and CME observations are from the SOHO/LASCO C2 coronograph. Each jet-­driven CME was relatively slow-­moving (approx. 200 - 300 km/s) compared to most CMEs; had angular width (20deg - 50deg) comparable to that of the streamer base; and was of the "streamer­-puff" variety, whereby a pre-existing streamer was transiently inflated but not removed (blown out) by the passage of the CME. Much of the chromospheric-­temperature plasma of the jets producing the CMEs escaped from the Sun, whereas relatively more of the chromospheric plasma in the non-CME-producing jets fell back to the solar surface. We also found that the CME-producing jets tended to be faster in speed and longer in duration than the non-CME-­producing jets. We expect that the jets result from eruptions of mini-filaments. We further propose that the CMEs are driven by magnetic twist injected into streamer-­base coronal loops when erupting twisted mini-filament field reconnects with the ambient field at the foot of those loops.

A Series of Jets that Drove Streamer-Puff CMEs from Giant Active Region of 2014

NASA Technical Reports Server (NTRS)

Panesar, Navdeep K.; Sterling, Alphonse C.; Moore, Ronald L.

2016-01-01

We investigate characteristics of solar coronal jets that originated from active region NOAA 12192 and produced coronal mass ejections (CMEs). This active region produced many non-jet major flare eruptions (X and M class) that made no CME. A multiitude of jets occurred from the southeast edge of the active region, and in contrast to the major-flare eruptions in the core, six of these jets resulted in CMEs. Our jet observations are from multiple SDO/AIA EUV channels, including 304, 171 and 193 Angstrom, and CME observations are taken from SOHO/LASCO C2 coronograph. Each jet-driven CME was relatively slow-moving (approximately 200 - 300 km s(sup-1) compared to most CMEs; had angular width (20deg - 50deg) comparable to that of the streamer base; and was of the "streamer-puff" variety, whereby a preexisting streamer was transiently inflated but not removed (blown out) by the passage of the CME. Much of the chromospheric-temperature plasma of the jets producing the CMEs escaped from the Sun, whereas relatively more of the chromospheric plasma in the non-CME-producing jets fell back to the solar surface. We also found that the CME-producing jets tended to be faster in speed and longer in duration than the non-CME-producing jets. We expect that the jets result from eruptions of mini-filaments. We further propose that the CMEs are driven by magnetic twist injected into streamer-base coronal loops when erupting twisted mini-filament field reconnects with the ambient field at the foot of those loops.

Increasing the Value of an Alternative Monetary Reinforcer Reduces Cigarette Choice in Adolescents.

PubMed

Cassidy, Rachel N; Tidey, Jennifer W; Kahler, Christopher W; Wray, Tyler B; Colby, Suzanne M

2015-12-01

Smoking can be conceptualized as an operant behavior maintained by the reinforcing effects of cigarettes. Changing the magnitude and availability of alternative reinforcers should shift behavior away from smoking. Adults' smoking behavior is sensitive to the magnitude and availability of alternative reinforcers; however, the extent to which the same is true for adolescents has not yet been shown in the laboratory. To test the sensitivity of adolescent smoking behavior to changes in the magnitude of alternative reinforcement, we gave adolescents who abstained overnight the opportunity to make 20 choices between receiving two puffs of their usual-brand cigarette or money. The magnitude of the monetary reinforcer was varied across sessions in counterbalanced order ($0.00, $0.10, and $0.50). Results indicated that adolescents' choices for puffs decreased as a function of increasing monetary reinforcer magnitude, while money choices increased. This effect was moderated by baseline smoking level and by gender, such that heavier-smoking participants and males made more cigarette choices when the alternative monetary value was zero, and decreased their choices more steeply in response to increasing monetary value. The current study validates a laboratory choice procedure for studying smoking in adolescents, and demonstrates that adolescent smoking behavior is sensitive to changes in the magnitude of concurrently available monetary reinforcers. The current paradigm can be adapted and applied to explore the effects of other variables that may affect cigarette choice in adolescents. © The Author 2015. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Predictors of the Onset of Cigarette Smoking: A Systematic Review of Longitudinal Population-Based Studies in Youth.

PubMed

Wellman, Robert J; Dugas, Erika N; Dutczak, Hartley; O'Loughlin, Erin K; Datta, Geetanjali D; Lauzon, Béatrice; O'Loughlin, Jennifer

2016-11-01

The onset of cigarette smoking typically occurs during childhood or early adolescence. Nicotine dependence symptoms can manifest soon after onset, contributing to sustained, long-term smoking. Previous reviews have not clarified the determinants of onset. In 2015, a systematic review of the literature in PubMed and EMBASE was undertaken to identify peer-reviewed prospective longitudinal studies published between January 1984 and August 2015 that investigated predictors of cigarette smoking onset among youth aged <18 years who had never smoked. Ninety-eight conceptually different potential predictors were identified in 53 studies. An increased risk of smoking onset was consistently (i.e., in four or more studies) associated with increased age/grade, lower SES, poor academic performance, sensation seeking or rebelliousness, intention to smoke in the future, receptivity to tobacco promotion efforts, susceptibility to smoking, family members' smoking, having friends who smoke, and exposure to films, whereas higher self-esteem and high parental monitoring/supervision of the child appeared to protect against smoking onset. Methodologic weaknesses were identified in numerous studies, including failure to account for attrition or for clustering in samples, and misidentification of potential confounders, which may have led to biased estimates of associations. Predictors of smoking onset for which there is robust evidence should be considered in the design of interventions to prevent first puff in order to optimize their effectiveness. Future research should seek to define onset clearly as the transition from never use to first use (e.g., first few puffs). Copyright © 2016 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Treatment of acute asthma: salbutamol via jet nebuliser vs spacer and metered dose inhaler.

PubMed

Robertson, C F; Norden, M A; Fitzgerald, D A; Connor, F L; Van Asperen, P P; Cooper, P J; Francis, P W; Allen, H D

1998-04-01

To compare the efficacy of salbutamol delivered by jet nebuliser (JN) with salbutamol via a pressurised metered dose inhaler (PMDI) and a large volume spacer (Volumatic) for management of acute asthma. A total of 160 children aged from 4 to 12 years presenting to an Emergency Department with acute asthma. The study was of multicentre (n=5) randomised, double blind, parallel design. Children weighing less than 25 kg received salbutamol 2.5 mg via the JN or 600 microg (six puffs) from the PMDI. Children over 25 kg received salbutamol 5 mg via the JN or 1200 microg (12 puffs) via the PMDI. Clinical score (range 0-12) and PEF (over 7 years) were recorded at baseline and 15, 30, 45 and 60 mins post administration. The improvement from baseline at 30 min in the clinical score was 1.87 for JN and 1.43 for PMDI (P=0.09) and at 60 min was 2.15 for JN and 1.12 for PMDI (P=0.0001). The improvement in PEF at 30 min was 51 L min(-1) for JN and 27 L min(-1) for PMDI (P=0.0007) and at 60 min was 57 L min(-1) for JN and 31.5 L min(-1) for PMDI (P=0.001). Administration of salbutamol via a PMDI and a large volume spacer device provides effective relief in the management of acute asthma in children, but to a lesser extent than a jet nebuliser. This difference may represent a dose response effect.

Secondhand Exposure to Vapors From Electronic Cigarettes

PubMed Central

Czogala, Jan; Fidelus, Bartlomiej; Zielinska-Danch, Wioleta; Travers, Mark J.; Sobczak, Andrzej

2014-01-01

Introduction: Electronic cigarettes (e-cigarettes) are designed to generate inhalable nicotine aerosol (vapor). When an e-cigarette user takes a puff, the nicotine solution is heated and the vapor is taken into lungs. Although no sidestream vapor is generated between puffs, some of the mainstream vapor is exhaled by e-cigarette user. The aim of this study was to evaluate the secondhand exposure to nicotine and other tobacco-related toxicants from e-cigarettes. Materials and Methods: We measured selected airborne markers of secondhand exposure: nicotine, aerosol particles (PM2.5), carbon monoxide, and volatile organic compounds (VOCs) in an exposure chamber. We generated e-cigarette vapor from 3 various brands of e-cigarette using a smoking machine and controlled exposure conditions. We also compared secondhand exposure with e-cigarette vapor and tobacco smoke generated by 5 dual users. Results: The study showed that e-cigarettes are a source of secondhand exposure to nicotine but not to combustion toxicants. The air concentrations of nicotine emitted by various brands of e-cigarettes ranged from 0.82 to 6.23 µg/m3. The average concentration of nicotine resulting from smoking tobacco cigarettes was 10 times higher than from e-cigarettes (31.60±6.91 vs. 3.32±2.49 µg/m3, respectively; p = .0081). Conclusions: Using an e-cigarette in indoor environments may involuntarily expose nonusers to nicotine but not to toxic tobacco-specific combustion products. More research is needed to evaluate health consequences of secondhand exposure to nicotine, especially among vulnerable populations, including children, pregnant women, and people with cardiovascular conditions. PMID:24336346

Effects of cigarette smoking and nicotine metabolite ratio on leukocyte telomere length.

PubMed

Verde, Zoraida; Reinoso-Barbero, Luis; Chicharro, Luis; Garatachea, Nuria; Resano, Pilar; Sánchez-Hernández, Ignacio; Rodríguez González-Moro, Jose Miguel; Bandrés, Fernando; Santiago, Catalina; Gómez-Gallego, Félix

2015-07-01

Studies of the effects of smoking on leukocyte telomere length (LTL) using cigarettes smoked per day or pack years smoked (PYS) present limitations. Reported high levels of smoking may not increase toxin exposure levels proportionally. Nicotine metabolism ratio (NMR) predicts total cigarette puff volume and overall exposure based on total N-nitrosamines, is highly reproducible and independent of time since the last cigarette. We hypothesized that smokers with higher NMRs will exhibit increased total puff volume, reflecting efforts to extract more nicotine from their cigarettes and increasing toxin exposure. In addition, higher levels of smoking could cause a gross damage in LTL. The urinary cotinine, 3-OH cotinine and nicotine levels of 147 smokers were analyzed using a LC/MS system Triple-Q6410. LTL and CYP2A6 genotype was determined by PCR in blood samples. We found a significant association between NMR and CYP2A6 genotype. Reduction in LTL was seen in relation to accumulated tobacco consumption and years smoking when we adjusted for age and gender. However, there were no significant differences between NMR values and LTL. In our study the higher exposure was associated with lower number of PYS. Smokers with reduced cigarette consumption may exhibit compensatory smoking behavior that results in no reduced tobacco toxin exposure. Our results suggest that lifetime accumulated smoking exposure could cause a gross damage in LTL rather than NMR or PYS. Nevertheless, a combination of smoking topography (NMR) and consumption (PYS) measures may provide useful information about smoking effects on health outcomes. Copyright © 2015 Elsevier Inc. All rights reserved.

An experimental test of the effect of acute anxious arousal and anxiety sensitivity on negative reinforcement smoking.

PubMed

Farris, Samantha G; Zvolensky, Michael J

2016-07-01

Although anxiety sensitivity has been reliably associated with smoking-anxiety comorbidity, there has not been a test of whether this construct moderates the effect of acute anxious arousal on actual smoking behavior. The present study utilized an experimental design to test the moderating role of anxiety sensitivity on laboratory-induced anxious arousal in terms of smoking urges and topography (puff style). Participants were adult daily smokers (n=90; Mage=43.6 SD =9.7); average 15.8 cigarettes per day). A between-subjects design was used; participants were randomly assigned to complete a biological challenge procedure consisting of either a single vital capacity inhalation of 35% carbon dioxide (CO2)-enriched air mixture or compressed room air. Smoking urges and smoking topography (puff behavior) were assessed before and after the challenge. Results revealed a significant interaction between anxiety sensitivity and experimental condition (b=-9.96, p=0.014), such that high anxiety sensitive smokers exposed to 35% CO2-enriched air reported significantly lower levels of smoking urges, relative to low anxiety sensitive smokers; the conditional effect of anxiety sensitivity was not observed for the room air condition. There were no significant interaction effects of experimental manipulation by anxiety sensitivity for any of the smoking topography outcomes. The present results suggest for smokers with higher levels of anxiety sensitivity, the acute experience of anxious arousal is related to decreased subjective smoking urges. These data invite future research to explore the reasons for dampened smoking urges, including cardiorespiratory symptom severity. © The Author(s) 2016.

Individual and combined effects of cannabis and tobacco on drug reward processing in non-dependent users.

PubMed

Hindocha, Chandni; Lawn, Will; Freeman, Tom P; Curran, H Valerie

2017-11-01

Cannabis and tobacco are often smoked simultaneously in joints, and this practice may increase the risks of developing tobacco and/or cannabis use disorders. Currently, there is no human experimental research on how these drugs interact on addiction-related measures. This study aimed to investigate how cannabis and tobacco, each alone and combined together in joints, affected individuals' demand for cannabis puffs and cigarettes, explicit liking of drug and non-drug-related stimuli and craving. A double-blind, 2 (active cannabis, placebo cannabis) × 2 (active tobacco, placebo tobacco) crossover design was used with 24 non-dependent cannabis and tobacco smokers. They completed a pleasantness rating task (PRT), a marijuana purchase task (MPT) and a cigarette purchase task (CPT) alongside measures of craving pre- and post-drug administration. Relative to placebo cannabis, active cannabis reduced liking of cannabis-associated stimuli and increased response time to all stimuli except cigarette-related stimuli. Relative to placebo cannabis, active cannabis decreased demand for cannabis puffs (trends for breakpoint and elasticity) and cigarettes (breakpoint, P max , O max ) on several characteristics of the purchase tasks. We found no evidence that active tobacco, both alone or combined with cannabis, had an effect on liking, demand or craving. Acutely, cannabis reduced liking of cannabis-related stimuli and demand for cannabis itself. Acute cannabis also reduced demand for cigarettes on the CPT. Acute tobacco administration did not affect demand or pleasantness ratings for cigarettes themselves or cannabis. In non-dependent cannabis and tobacco co-users, tobacco did not influence the rewarding effects of cannabis.

High Performance Poly(viologen)-Graphene Nanocomposite Battery Materials with Puff Paste Architecture.

PubMed

Beladi-Mousavi, Seyyed Mohsen; Sadaf, Shamaila; Mahmood, Arsalan Mado; Walder, Lorenz

2017-09-26

Four linear poly(viologens) (PV1, PV2: phenylic, PV3: benzylic, and PV4: aliphatic) in tight molecular contact with reduced graphene oxide (rGO), that is, PV@rGO, were prepared and used as anodic battery materials. These composites show exceptionally high, areal, volumetric, and current densities, for example, PV1@rGO composites (with 15 wt % rGO, corresponding to 137 mAh g -1 ) show 13.3 mAh cm -2 at 460 μm and 288 mAh cm -3 with 98% Coulombic efficiency at current densities up to 1000 A g -1 , better than any reported organic materials. These remarkable performances are based on (i) molecular self-assembling of PVs on individual GO sheets yielding colloidal PV@GO and (ii) efficient GO/rGO transformation electrocatalyzed by PVs. Ion breathing during charging/discharging was studied by electrochemical quartz crystal microbalance and electrochemical atomic force microscopy revealing an absolute reversible and strongly anisotropic thickness oscillation of PV1@rGO at a right angle to the macroscopic current collector. It is proposed that such stress-free breathing is the key property for good cyclability of the battery material. The anisotropy is related to a puff paste architecture of rGO sheets parallel to the macroscopic current collector. A thin graphite sheet electrode with an areal capacity of 1.23 mAh cm -2 is stable over 200 bending cycles, making the material applicable for wearable electronics. The polymer acts as a lubricant between the rGO layers if shearing forces are active.

Increased Serum and Urinary Oxytocin Concentrations after Nasal Administration in Beagle Dogs

PubMed Central

Temesi, Andrea; Thuróczy, Julianna; Balogh, Lajos; Miklósi, Ádám

2017-01-01

In recent years more and more studies have revealed the effect of extraneous oxytocin on the social behavior of dogs. The distribution of administered oxytocin in different physiologically relevant compartments is important because this knowledge forms the basis for the timing of behavior tests after the administration. Most behavioral studies rely on the non-invasive intranasal application of oxytocin. The aim of this study was to determine the time course of intranasal administered oxytocin secretion into blood and urine and also establish a connection between intranasal received oxytocin and urinary cortisol in dogs. In our experiment, four dogs received three puffs, 12 IU intranasal oxytocin treatment, two dogs received three puffs intranasal placebo treatment. Blood and urine samples were collected immediately prior to the administration then regularly during 4 h. After nasal oxytocin application, the serum oxytocin concentration increased, reached a maximum 15 min after the treatment and then rapidly returned to baseline levels 45 min later. The peak urinary oxytocin concentration occurred between 45 and 60 min after administration and returned to baseline levels slowly. We found considerable differences among individuals in the secretion of oxytocin in both the serum and the urinary oxytocin concentration measurements. Our results confirm that intranasally administered oxytocin passes into the blood stream. The time course of intranasally administered oxytocin secretion is similar to the time course of intravenously administered oxytocin secretion, and the peak values are also similar in both the serum and the urinary oxytocin concentration measurements, although there are large individual differences. PMID:28929104

Salt Toxicity (Sodium Intake): A Serious Threat to Infants and Children of Pakistan

PubMed Central

WASEEM, Amir; NAFEES, Muhammad; MURTAZA, Ghulam; SAJJAD, Ashif; MEHMOOD, Zahid; SIDDIQI, Abdul Rauf

2014-01-01

Abstract Background Excess sodium intake can lead to hypertension, the primary risk factor for cardiovascular disease. The aim of this study was to investigate the sodium and potassium contents of foodstuff used by infants and children of Pakistan. Methods We analyzed the sodium and potassium contents of infant milk formula (<6 months), follow up milk formula (>6 months), baby food (cereals), biscuits, fruit juices, potato chips (crisps), cheese puffs, roasted cereals (salty), ice cream cones (kulfi) all of which are the processed food extensively used by the children. The amount of sodium and potassium contents in drinking water of few cities of Pakistan were also considered to assess the additional sodium/potassium in the preparation of milk using infant milk formula. Results Na to K ratio (Na:K) was determined 0.3-1.23, 0.3-1.16, 0.33-0.82, 0.54-2.68, 0.51-0.85, 2.86 and 1.02 for infant milk formula (<6 months), follow up milk formula (>6 months), baby food (cereals), biscuits, fruit juices, potato chips (crisps, cheese puffs, roasted cereals), ice cream cones (kulfi), respectively. Conclusion The higher sodium content is present than most of the quoted values; whereas lower potassium is present than the recommended values. The higher Na:K ratio indicates the severity of the situation where it is commonly stated that “higher an individual’s salt intake, the higher an individual’s blood pressure". Present study indicates that nearly all Pakistani children consume substantially more salt than they need which will affect health status in later life. PMID:26175974

Cultivation and partial characterization of spiroplasmas in cell cultures.

PubMed Central

Steiner, T; McGarrity, G J; Phillips, D M

1982-01-01

Spiroplasmas were propagated in the Drosophila melanogaster cell line Dm-1. Spiroplasma citri and unidentified strains (corn shunt organism, 277F [tick isolate], powder puff, BNR-1, honey bee, and OBMG) grew to 10(8) to 10(9) colony-forming units per ml and could be passaged. Cytopathic effect (CPE) varied with the infecting spiroplasma. The honey bee isolate killed Dm-1 within 2 to 4 days and produced CPE in four mammalian cells tested. At 25 degrees C, suckling mouse cataract agent produced no CPE in Dm-1 cells. Dm-1 cells did not support growth of the spiroplasmal sex ratio organism. Spiroplasmas could be detected in the cell cultures by agar inoculation, dark-field microscopy, scanning electron microscopy, and DNA fluorescent staining. The uridine phosphorylase test showed significant levels of conversion of [14C]uridine to [14C]uracil for all but some plant isolates: S. citri, corn shunt organism, lettuce, cactus, and powder puff strains, the first mycoplasmas to lack the enzyme. Primary isolations of corn shunt organism from infected corn plants were made in Dm-1 and I-XII cultures. The course of corn stunt organism infection of Dm-1 was monitored for three passages. The use of agarose and Dienes staining of the colonies improved growth and colony counting of corn stunt organism. The number of viable infected DM-1 cells decreased from 1.2 x 10(7) at passage 1 to 7.0 x 10(6) at passage 2 and 3 x 10(5) at passage 3. Images PMID:6797950

Electrical stimulation of the rostral medial prefrontal cortex in rabbits inhibits the expression of conditioned eyelid responses but not their acquisition

PubMed Central

Leal-Campanario, Rocío; Fairén, Alfonso; Delgado-García, José M.; Gruart, Agnès

2007-01-01

We have studied the role of rostral medial prefrontal cortex (mPFC) on reflexively evoked blinks and on classically conditioned eyelid responses in alert-behaving rabbits. The rostral mPFC was identified by its afferent projections from the medial half of the thalamic mediodorsal nuclear complex. Classical conditioning consisted of a delay paradigm using a 370-ms tone as the conditioned stimulus (CS) and a 100-ms air puff directed at the left cornea as the unconditioned stimulus (US). The CS coterminated with the US. Electrical train stimulation of the contralateral rostral mPFC produced a significant inhibition of air-puff-evoked blinks. The same train stimulation of the rostral mPFC presented during the CS–US interval for 10 successive conditioning sessions significantly reduced the generation of conditioned responses (CRs) as compared with values reached by control animals. Interestingly, the percentage of CRs almost reached control values when train stimulation of the rostral mPFC was removed from the fifth conditioning session on. The electrical stimulation of the rostral mPFC in well conditioned animals produced a significant decrease in the percentage of CRs. Moreover, the stimulation of the rostral mPFC was also able to modify the kinematics (latency, amplitude, and velocity) of evoked CRs. These results suggest that the rostral mPFC is a potent inhibitor of reflexively evoked and classically conditioned eyeblinks but that activation prevents only the expression of CRs, not their latent acquisition. Functional and behavioral implications of this inhibitory role of the rostral mPFC are discussed. PMID:17592148

A deterministic model predicts the properties of stochastic calcium oscillations in airway smooth muscle cells.

PubMed

Cao, Pengxing; Tan, Xiahui; Donovan, Graham; Sanderson, Michael J; Sneyd, James

2014-08-01

The inositol trisphosphate receptor ([Formula: see text]) is one of the most important cellular components responsible for oscillations in the cytoplasmic calcium concentration. Over the past decade, two major questions about the [Formula: see text] have arisen. Firstly, how best should the [Formula: see text] be modeled? In other words, what fundamental properties of the [Formula: see text] allow it to perform its function, and what are their quantitative properties? Secondly, although calcium oscillations are caused by the stochastic opening and closing of small numbers of [Formula: see text], is it possible for a deterministic model to be a reliable predictor of calcium behavior? Here, we answer these two questions, using airway smooth muscle cells (ASMC) as a specific example. Firstly, we show that periodic calcium waves in ASMC, as well as the statistics of calcium puffs in other cell types, can be quantitatively reproduced by a two-state model of the [Formula: see text], and thus the behavior of the [Formula: see text] is essentially determined by its modal structure. The structure within each mode is irrelevant for function. Secondly, we show that, although calcium waves in ASMC are generated by a stochastic mechanism, [Formula: see text] stochasticity is not essential for a qualitative prediction of how oscillation frequency depends on model parameters, and thus deterministic [Formula: see text] models demonstrate the same level of predictive capability as do stochastic models. We conclude that, firstly, calcium dynamics can be accurately modeled using simplified [Formula: see text] models, and, secondly, to obtain qualitative predictions of how oscillation frequency depends on parameters it is sufficient to use a deterministic model.

Linear Transformer Drivers for Z-pinch Based Propulsion

NASA Technical Reports Server (NTRS)

Adams, Robert; Seidler, William; Giddens, Patrick; Fabisinski, Leo; Cassibry, Jason

2017-01-01

The MSFC/UAH team has been developing of a novel power management and distribution system called a Linear Transformer Driver (LTD). LTD's hold the promise of dramatically reducing the required mass to drive a z-pinch by replacing the capacitor banks which constitute half the mass of the entire system. The MSFC?UAH tea, is developing this technology in hope of integrating it with the Pulsed Fission Fusion (PuFF) propulsion concept. High-Voltage pulsed power systems used for Z-Pinch experimentation have in the past largely been based on Marx Generators. Marx generators deliver the voltage and current required for the Z-Pinch, but suffer from two significant drawbacks when applied to a flight system: they are very massive, consisting of high-voltage capacitor banks insulated in oil-filled tanks and they do not lend themselves to rapid pulsing. The overall goal of Phase 2 is to demonstrate the construction of a higher voltage stack from a number of cavities each of the design proven in Phase 1 and to characterize and understand the techniques for designing the stack. The overall goal of Phase 3 is to demonstrate the feasibility of constructing a higher energy cavity from a number of smaller LTD stacks, to characterize and understand the way in which the constituent stacks combine, and to extend this demonstration LTD to serve as the basis for a 64 kJ pulse generator for Z-Pinch experiments.

Experimental and theoretical study on emission spectra of a nitrogen photoionized plasma induced by intense EUV pulses

NASA Astrophysics Data System (ADS)

Saber, Ismail; Bartnik, Andrzej; Skrzeczanowski, Wojciech; Wachulak, Przemyslaw; Jarocki, Roman; Fiedorowicz, Henryk; Limpouch, Jiri

2018-01-01

Spectral lines of low-temperature nitrogen photoionized plasma were investigated. The photoionized plasma was created in the result of irradiation N2 gas using laser plasma EUV radiation pulses. The source was based on a 10J/10ns Nd:YAG (λ = 1064 nm) laser system and a gas puff target. The EUV radiation pulses were collected and focused using a grazing incidence multifoil EUV collector. The emission spectra were measured in the ultraviolet and visible (UV/Vis) range. It was found that the plasma emission lines in the lower region of the UV range are relativley weak. Nonetheless, a part of the spectra contains strong molecular band in the 300 - 430 nm originated from second positive and first negative systems band transitions of nitrogen. These molecular band transitions were identified using a code for study the diatomic molecules, LIFBASE. The vibrational band of Δv = 0 and ±1 transitions were significantly populated than of that with Δv = ±2 and 3 transitions. A comparison of the calculated and measured spectrum is presented. With an assumption of a local thermodynamic equilibrium (LTE), the vibrational temperature was determined from the integrated band intensities with the help of the Boltzmann plot method and compared to the temperature predicted by SPECAIR and LIFBASE simulations. A summary of the results and the variations in the vibrational temperatures was discussed.