Participation in the Cluster Magnetometer Consortium for the Cluster Mission

NASA Technical Reports Server (NTRS)

Kivelson, Margaret

1997-01-01

Prof. M. G. Kivelson (UCLA) and Dr. R. C. Elphic (LANL) are Co-investigators on the Cluster Magnetometer Consortium (CMC) that provided the fluxgate magnetometers and associated mission support for the Cluster Mission. The CMC designated UCLA as the site with primary responsibility for the inter-calibration of data from the four spacecraft and the production of fully corrected data critical to achieving the mission objectives. UCLA was also charged with distributing magnetometer data to the U.S. Co-investigators. UCLA also supported the Technical Management Team, which was responsible for the detailed design of the instrument and its interface. In this final progress report we detail the progress made by the UCLA team in achieving the mission objectives.

Flight 1 technical report for experiment 74-37 contained polycrystalline solidification in low-G

NASA Technical Reports Server (NTRS)

Papaziak, J. M.; Kattamis, T. Z.

1976-01-01

A .005 M solution of fluorescein in cyclohexanol was directionally solidified in a standard 10 x 10 x 45mm UV silica cuvette, using a bottom thermoelectric chilling device. Progress of the experiment was monitored by time lapse photography. During flight (SPAR I) the camera malfunctioned and only one quarter of the expected data were collected. Comparison of flight and ground specimens indicated that: (1) The dark green layer observed ahead of the solid-liquid interface which is most likely the solute-enriched zone, appears to be wider in the flight specimen; (2) Parasitic nucleation ahead of the solid-liquid interface in the flight sample led to an irregularly shaped interface, smaller grain size, equiaxed grain morphology and a larger average macroscopic growth rate; (3) The formation of equiaxed grains ahead of the solid-liquid interface in the flight specimen may be attributed to ordered islands within the liquid, which survived remelting because of the low degree of superheating (approximately equal to 1.5 C), did not settle because of reduced gravity and acted as nuclei during cooling.

High speed fiber optics local area networks: Design and implementation

NASA Technical Reports Server (NTRS)

Tobagi, Fouad A.

1988-01-01

The design of high speed local area networks (HSLAN) for communication among distributed devices requires solving problems in three areas: (1) the network medium and its topology; (2) the medium access control; and (3) the network interface. Considerable progress has been made in all areas. Accomplishments are divided into two groups according to their theoretical or experimental nature. A brief summary is given in Section 2, including references to papers which appeared in the literature, as well as to Ph.D. dissertations and technical reports published at Stanford University.

Probabilistic Structural Analysis Methods (PSAM) for select space propulsion system components

NASA Technical Reports Server (NTRS)

1991-01-01

This annual report summarizes the work completed during the third year of technical effort on the referenced contract. Principal developments continue to focus on the Probabilistic Finite Element Method (PFEM) which has been under development for three years. Essentially all of the linear capabilities within the PFEM code are in place. Major progress in the application or verifications phase was achieved. An EXPERT module architecture was designed and partially implemented. EXPERT is a user interface module which incorporates an expert system shell for the implementation of a rule-based interface utilizing the experience and expertise of the user community. The Fast Probability Integration (FPI) Algorithm continues to demonstrate outstanding performance characteristics for the integration of probability density functions for multiple variables. Additionally, an enhanced Monte Carlo simulation algorithm was developed and demonstrated for a variety of numerical strategies.

Web-Based Interactive Electronic Technical Manual (IETM) Common User Interface Style Guide, Version 2.0

DTIC Science & Technology

2003-07-01

Technical Report WEB-BASED INTERACTIVE ELECTRONIC TECHNICAL MANUAL (IETM) COMMON USER INTERFACE STYLE GUIDE Version 2.0 – July 2003 by L. John Junod ...ACKNOWLEDGEMENTS The principal authors of this document were: John Junod – NSWC, Carderock Division, Phil Deuell – AMSEC LLC, Kathleen Moore

Product Development as a Fuzzy Interface between Technical and Non-technical Education.

ERIC Educational Resources Information Center

Masarnau, Juan

1988-01-01

Discusses a product development structure, including marketing, design, technology, industrial manufacturing, reasoning, and objects. Describes needs of the interface in terms of marketing, industrial design, technology, and industry. (YP)

Reactivity of young chars via energetic distribution measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calo, J.M.; Lilly, W.D.

1991-01-01

The current project is directed at developing related techniques for the characterization and prediction/correlation of the reactivity of young'' chars to steam and oxygen. Of particular interest is mapping of the reactivity behavior of the resultant chars, as revealed by the energetic heterogeneity of the complexes with char preparation conditions; i.e., heating rate and ultimate temperature. In this first quarterly technical progress report we present the background of the project and the research program for the proposed investigations. The following work was accomplished on the experimental apparatus: a new set of electronics for the UTi quadrupole mass spectrometer head wasmore » purchased and delivered. The Temperature Programmed Desorption (TPD) System was moved to another laboratory and interfaced with the mass spectrometer system. A Polycold{trademark} freon refrigeration system was repaired and interfaced with the vacuum system for the TPD apparatus. It will be used to cool the diffusion pump trap. 60 refs.« less

[Concepts of development of the neurosurgical operative environment in the 21st century].

PubMed

Apuzzo, M; Liu, C

2002-01-01

The operative environment has to a large extent defines the "state of the art and science" of neurosurgery, which is now undergoing rapid reinvention. In order to remain current, each neurosurgeon should periodically reconsider their personal operative environment and its functional design with reference to modernity of practice as currently defined. Historical trends and their analysis offer predictive guides for development of such settings with an eye toward the future. Examination of technical developments in decade timeframes defines the progress in capability and need. Progressive minimalism of manipulation and the presence of operative definition with increasing precision are evident, with concurrent miniaturization of attendant computerized support systems, sensors, robotic interfaces, and imaging devices. These trends and developments offer the opportunity for simplificity of setting design with higher functionality as the desired endpoint.

Where the lay and the technical meet: Using an anthropology of interfaces to explain persistent reproductive health disparities in West Africa.

PubMed

Jaffré, Yannick; Suh, Siri

2016-05-01

Despite impressive global investment in reproductive health programs in West Africa, maternal mortality remains unacceptably high and obstetric care is often inadequate. Fertility is among the highest in the world, while contraceptive prevalence remains among the lowest. This paper explores the social and technical dimensions of this situation. We argue that effective reproductive health programs require analyzing the interfaces between technical programs and the social logics and behaviors of health professionals and client populations. Significant gaps between health programs' goals and the behaviors of patients and health care professionals have been observed. While public health projects aim to manage reproduction, sexuality, fertility, and professional practices are regulated socially. Such projects may target technical practices, but access to care is greatly influenced by social norms and ethics. This paper shows how an empirical anthropology that investigates the social and technical interfaces of reproduction can contribute to improved global health. Copyright © 2016 Elsevier Ltd. All rights reserved.

48 CFR 742.1170-4 - Progress reporting requirements and contract clause.

Code of Federal Regulations, 2010 CFR

2010-10-01

... progress. (b) Because the cognizant technical officer is the individual most familiar with the contractor's performance, the contractor must submit the progress reports directly to the cognizant technical officer. The cognizant technical officer must review the reports and advise the contracting officer, in writing, of any...

Application of Interface Technology in Progressive Failure Analysis of Composite Panels

NASA Technical Reports Server (NTRS)

Sleight, D. W.; Lotts, C. G.

2002-01-01

A progressive failure analysis capability using interface technology is presented. The capability has been implemented in the COMET-AR finite element analysis code developed at the NASA Langley Research Center and is demonstrated on composite panels. The composite panels are analyzed for damage initiation and propagation from initial loading to final failure using a progressive failure analysis capability that includes both geometric and material nonlinearities. Progressive failure analyses are performed on conventional models and interface technology models of the composite panels. Analytical results and the computational effort of the analyses are compared for the conventional models and interface technology models. The analytical results predicted with the interface technology models are in good correlation with the analytical results using the conventional models, while significantly reducing the computational effort.

Shuttle payload interface verification equipment study. Volume 2: Technical document, part 1

NASA Technical Reports Server (NTRS)

1976-01-01

The technical analysis is reported that was performed during the shuttle payload interface verification equipment study. It describes: (1) the background and intent of the study; (2) study approach and philosophy covering all facets of shuttle payload/cargo integration; (3)shuttle payload integration requirements; (4) preliminary design of the horizontal IVE; (5) vertical IVE concept; and (6) IVE program development plans, schedule and cost. Also included is a payload integration analysis task to identify potential uses in addition to payload interface verification.

Optimizing the NASA Technical Report Server

NASA Technical Reports Server (NTRS)

Nelson, Michael L.; Maa, Ming-Hokng

1996-01-01

The NASA Technical Report Server (NTRS), a World Wide Web report distribution NASA technical publications service, is modified for performance enhancement, greater protocol support, and human interface optimization. Results include: Parallel database queries, significantly decreasing user access times by an average factor of 2.3; access from clients behind firewalls and/ or proxies which truncate excessively long Uniform Resource Locators (URLs); access to non-Wide Area Information Server (WAIS) databases and compatibility with the 239-50.3 protocol; and a streamlined user interface.

Education, Technical Progress, and Economic Growth: The Case of Taiwan.

ERIC Educational Resources Information Center

Lin, T.-C.

2003-01-01

Investigates the effect of education and the role of technical progress on economic growth in Taiwan from 1965-2000. Finds that education has a positive and significant effect on growth, but the role of technical progress does not appear to be extraordinarily important. Furthermore, no markedly significant relationships exist between capital and…

Webinar May 17: Fuel Cell Electric Bus Progress Toward Meeting Technical

Science.gov Websites

Targets | News | NREL Webinar May 17: Fuel Cell Electric Bus Progress toward Meeting Technical Targets Webinar May 17: Fuel Cell Electric Bus Progress toward Meeting Technical Targets May 14, 2018 The U.S. Department of Energy's (DOE's) Fuel Cell Technologies Office will present a live webinar titled

Enabling technologies built on a sonochemical platform: challenges and opportunities.

PubMed

Cintas, Pedro; Tagliapietra, Silvia; Caporaso, Marina; Tabasso, Silvia; Cravotto, Giancarlo

2015-07-01

Scientific and technological progress now occurs at the interface between two or more scientific and technical disciplines while chemistry is intertwined with almost all scientific domains. Complementary and synergistic effects have been found in the overlay between sonochemistry and other enabling technologies such as mechanochemistry, microwave chemistry and flow-chemistry. Although their nature and effects are intrinsically different, these techniques share the ability to significantly activate most chemical processes and peculiar phenomena. These studies offer a comprehensive overview of sonochemistry, provide a better understanding of correlated phenomena (mechanochemical effects, hot spots, etc.), and pave the way for emerging applications which unite hybrid reactors. Copyright © 2014 Elsevier B.V. All rights reserved.

An object-oriented approach to deploying highly configurable Web interfaces for the ATLAS experiment

NASA Astrophysics Data System (ADS)

Lange, Bruno; Maidantchik, Carmen; Pommes, Kathy; Pavani, Varlen; Arosa, Breno; Abreu, Igor

2015-12-01

The ATLAS Technical Coordination disposes of 17 Web systems to support its operation. These applications, whilst ranging from managing the process of publishing scientific papers to monitoring radiation levels in the equipment in the experimental cavern, are constantly prone to changes in requirements due to the collaborative nature of the experiment and its management. In this context, a Web framework is proposed to unify the generation of the supporting interfaces. FENCE assembles classes to build applications by making extensive use of JSON configuration files. It relies heavily on Glance, a technology that was set forth in 2003 to create an abstraction layer on top of the heterogeneous sources that store the technical coordination data. Once Glance maps out the database modeling, records can be referenced in the configuration files by wrapping unique identifiers around double enclosing brackets. The deployed content can be individually secured by attaching clearance attributes to their description thus ensuring that view/edit privileges are granted to eligible users only. The framework also provides tools for securely writing into a database. Fully HTML5-compliant multi-step forms can be generated from their JSON description to assure that the submitted data comply with a series of constraints. Input validation is carried out primarily on the server- side but, following progressive enhancement guidelines, verification might also be performed on the client-side by enabling specific markup data attributes which are then handed over to the jQuery validation plug-in. User monitoring is accomplished by thoroughly logging user requests along with any POST data. Documentation is built from the source code using the phpDocumentor tool and made readily available for developers online. Fence, therefore, speeds up the implementation of Web interfaces and reduces the response time to requirement changes by minimizing maintenance overhead.

25 CFR 547.8 - What are the minimum technical software standards applicable to Class II gaming systems?

Code of Federal Regulations, 2012 CFR

2012-04-01

... OF CLASS II GAMES § 547.8 What are the minimum technical software standards applicable to Class II... of Class II games. (a) Player interface displays. (1) If not otherwise provided to the player, the player interface shall display the following: (i) The purchase or wager amount; (ii) Game results; and...

25 CFR 547.8 - What are the minimum technical software standards applicable to Class II gaming systems?

Code of Federal Regulations, 2011 CFR

2011-04-01

... OF CLASS II GAMES § 547.8 What are the minimum technical software standards applicable to Class II... of Class II games. (a) Player interface displays. (1) If not otherwise provided to the player, the player interface shall display the following: (i) The purchase or wager amount; (ii) Game results; and...

25 CFR 547.8 - What are the minimum technical software standards applicable to Class II gaming systems?

Code of Federal Regulations, 2010 CFR

2010-04-01

... OF CLASS II GAMES § 547.8 What are the minimum technical software standards applicable to Class II... of Class II games. (a) Player interface displays. (1) If not otherwise provided to the player, the player interface shall display the following: (i) The purchase or wager amount; (ii) Game results; and...

25 CFR 30.111 - When should the tribal governing body or school board request technical assistance?

Code of Federal Regulations, 2011 CFR

2011-04-01

... request technical assistance? 30.111 Section 30.111 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR EDUCATION ADEQUATE YEARLY PROGRESS Defining Adequate Yearly Progress Technical Assistance § 30.111 When should the tribal governing body or school board request technical assistance? In order to...

Railroad track inspection interface demonstration : final report.

DOT National Transportation Integrated Search

2016-01-01

This project developed a track data user interface utilizing the Google Glass optical display device. The interface allows the user : to recall data stored remotely and view the data on the Google Glass. The technical effort required developing a com...

25 CFR 30.110 - What is the process for requesting technical assistance to develop an alternative definition of AYP?

Code of Federal Regulations, 2011 CFR

2011-04-01

..., DEPARTMENT OF THE INTERIOR EDUCATION ADEQUATE YEARLY PROGRESS Defining Adequate Yearly Progress Technical Assistance § 30.110 What is the process for requesting technical assistance to develop an alternative... 25 Indians 1 2011-04-01 2011-04-01 false What is the process for requesting technical assistance...

25 CFR 30.110 - What is the process for requesting technical assistance to develop an alternative definition of AYP?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false What is the process for requesting technical assistance..., DEPARTMENT OF THE INTERIOR EDUCATION ADEQUATE YEARLY PROGRESS Defining Adequate Yearly Progress Technical Assistance § 30.110 What is the process for requesting technical assistance to develop an alternative...

The EOSDIS software challenge

NASA Astrophysics Data System (ADS)

Jaworski, Allan

1993-08-01

The Earth Observing System (EOS) Data and Information System (EOSDIS) will serve as a major resource for the earth science community, supporting both command and control of complex instruments onboard the EOS spacecraft and the archiving, distribution, and analysis of data. The scale of EOSDIS and the volume of multidisciplinary research to be conducted using EOSDIS resources will produce unparalleled needs for technology transparency, data integration, and system interoperability. The scale of this effort far outscopes any previous scientific data system in its breadth or operational and performance needs. Modern hardware technology can meet the EOSDIS technical challenge. Multiprocessing speeds of many giga-flops are being realized by modern computers. Online storage disk, optical disk, and videocassette libraries with storage capacities of many terabytes are now commercially available. Radio frequency and fiber optics communications networks with gigabit rates are demonstrable today. It remains, of course, to perform the system engineering to establish the requirements, architectures, and designs that will implement the EOSDIS systems. Software technology, however, has not enjoyed the price/performance advances of hardware. Although we have learned to engineer hardware systems which have several orders of magnitude greater complexity and performance than those built in the 1960's, we have not made comparable progress in dramatically reducing the cost of software development. This lack of progress may significantly reduce our capabilities to achieve economically the types of highly interoperable, responsive, integraded, and productive environments which are needed by the earth science community. This paper describes some of the EOSDIS software requirements and current activities in the software community which are applicable to meeting the EOSDIS challenge. Some of these areas include intelligent user interfaces, software reuse libraries, and domain engineering. Also included are discussions of applicable standards in the areas of operating systems interfaces, user interfaces, communications interfaces, data transport, and science algorithm support, and their role in supporting the software development process.

Update on Progress of Space Station Integrated Kinetic Launcher for Orbital Payload Systems (SSIKLOPS) - Cyclops

NASA Technical Reports Server (NTRS)

Newswander, Daniel; Smith, James P.; Lamb, Craig R.; Ballard, Perry G.

2014-01-01

The Space Station Integrated Kinetic Launcher for Orbital Payload Systems (SSIKLOPS), known as "Cyclops" to the International Space Station (ISS) community, was introduced last August (2013) during Technical Session V: From Earth to Orbit of the 27th Annual AIAA/USU Conference on Small Satellites. Cyclops is a collaboration between the NASA ISS Program, NASA Johnson Space Center Engineering, and Department of Defense (DoD) Space Test Program (STP) communities to develop a dedicated 50-100 kg class ISS small satellite deployment system. This paper will address the progress of Cyclops through its fabrication, assembly, flight certification, and on-orbit demonstration phases. It will also go into more detail regarding its anatomy, its satellite deployment concept of operations, and its satellite interfaces and requirements. Cyclops is manifested to fly on Space-X 4 which is currently scheduled in July 2014 with its initial satellite deployment demonstration of DoD STP's SpinSat and UT/TAMU's Lonestar satellites being late summer or fall of 2014.

Cognitive Task Analysis, Interface Design, and Technical Troubleshooting.

ERIC Educational Resources Information Center

Steinberg, Linda S.; Gitomer, Drew H.

A model of the interface design process is proposed that makes use of two interdependent levels of cognitive analysis: the study of the criterion task through an analysis of expert/novice differences and the evaluation of the working user interface design through the application of a practical interface analysis methodology (GOMS model). This dual…

TangibleCubes — Implementation of Tangible User Interfaces through the Usage of Microcontroller and Sensor Technology

NASA Astrophysics Data System (ADS)

Setscheny, Stephan

The interaction between human beings and technology builds a central aspect in human life. The most common form of this human-technology interface is the graphical user interface which is controlled through the mouse and the keyboard. In consequence of continuous miniaturization and the increasing performance of microcontrollers and sensors for the detection of human interactions, developers receive new possibilities for realising innovative interfaces. As far as this movement is concerned, the relevance of computers in the common sense and graphical user interfaces is decreasing. Especially in the area of ubiquitous computing and the interaction through tangible user interfaces a highly impact of this technical evolution can be seen. Apart from this, tangible and experience able interaction offers users the possibility of an interactive and intuitive method for controlling technical objects. The implementation of microcontrollers for control functions and sensors enables the realisation of these experience able interfaces. Besides the theories about tangible user interfaces, the consideration about sensors and the Arduino platform builds a main aspect of this work.

Comparison of the Booster Interface Temperature in Stainless Steel (SS) V-Channel versus the Aluminum (Al) Y-Channel Primer Chamber Assemblies (PCAs). Volume 1; Technical Assessment Report

NASA Technical Reports Server (NTRS)

Garcia, Roberto; Saulsberry, Regor L.

2011-01-01

NASA's Technical Fellow for Propulsion, requested a technical assessment of the performance improvement achieved by the introduction of the stainless steel (SS) V-channel compared to the aluminum (Al) Y-channel Primer Chamber Assembly (PCA) design. The SS V-channel PCA was developed for NASA's Mars Science Laboratory (MSL) Project. The principle focus of the assessment was to measure the transient temperature at the booster interface with both designs. This document contains the findings of the assessment.

14 CFR 1274.701 - Suspension or termination.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Agreement if the recipient is not making anticipated technical progress, if the recipient materially changes...) Similarly, the recipient may terminate the agreement if, for example, technical progress is not being made, if the commercial recipient shifts its technical emphasis, or if other technological advances have...

14 CFR 1274.701 - Suspension or termination.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Agreement if the recipient is not making anticipated technical progress, if the recipient materially changes...) Similarly, the recipient may terminate the agreement if, for example, technical progress is not being made, if the commercial recipient shifts its technical emphasis, or if other technological advances have...

Modeling Geometry and Progressive Failure of Material Interfaces in Plain Weave Composites

NASA Technical Reports Server (NTRS)

Hsu, Su-Yuen; Cheng, Ron-Bin

2010-01-01

A procedure combining a geometrically nonlinear, explicit-dynamics contact analysis, computer aided design techniques, and elasticity-based mesh adjustment is proposed to efficiently generate realistic finite element models for meso-mechanical analysis of progressive failure in textile composites. In the procedure, the geometry of fiber tows is obtained by imposing a fictitious expansion on the tows. Meshes resulting from the procedure are conformal with the computed tow-tow and tow-matrix interfaces but are incongruent at the interfaces. The mesh interfaces are treated as cohesive contact surfaces not only to resolve the incongruence but also to simulate progressive failure. The method is employed to simulate debonding at the material interfaces in a ceramic-matrix plain weave composite with matrix porosity and in a polymeric matrix plain weave composite without matrix porosity, both subject to uniaxial cyclic loading. The numerical results indicate progression of the interfacial damage during every loading and reverse loading event in a constant strain amplitude cyclic process. However, the composites show different patterns of damage advancement.

Magnetic resonance-compatible robotic and mechatronics systems for image-guided interventions and rehabilitation: a review study.

PubMed

Tsekos, Nikolaos V; Khanicheh, Azadeh; Christoforou, Eftychios; Mavroidis, Constantinos

2007-01-01

The continuous technological progress of magnetic resonance imaging (MRI), as well as its widespread clinical use as a highly sensitive tool in diagnostics and advanced brain research, has brought a high demand for the development of magnetic resonance (MR)-compatible robotic/mechatronic systems. Revolutionary robots guided by real-time three-dimensional (3-D)-MRI allow reliable and precise minimally invasive interventions with relatively short recovery times. Dedicated robotic interfaces used in conjunction with fMRI allow neuroscientists to investigate the brain mechanisms of manipulation and motor learning, as well as to improve rehabilitation therapies. This paper gives an overview of the motivation, advantages, technical challenges, and existing prototypes for MR-compatible robotic/mechatronic devices.

Progress in Applied Surface, Interface and Thin Film Science 2015. Solar Renewable Energy News IV, November 23-26, 2015, Florence, Italy (SURFINT-SREN IV)

NASA Astrophysics Data System (ADS)

2017-02-01

The main goal of the conference is to contribute to new knowledge in surface, interface, ultra-thin films and very-thin films science of inorganic and organic materials by the most rapid interactive manner - by direct communication among scientists of corresponding research fields. The list of topics indicates that conference interests cover the development of basic theoretical physical and chemical principles and performance of surfaces-, thin films-, and interface-related procedures, and corresponding experimental research on atomic scale. Topical results are applied at development of new inventive industrial equipments needed for investigation of electrical, optical, and structural properties, and other parameters of atomic-size research objects. The conference range spreads, from physical point of view, from fundamental research done on sub-atomic and quantum level to production of devices built on new physical principles. The conference topics include also presentation of principally new devices in following fields: solar cells, liquid crystal displays, high-temperature superconductivity, and sensors. During the event, special attention will be given to evaluation of scientific and technical quality of works prepared by PhD students, to deep ecological meaning of solar cell energy production, and to exhibitions of companies.

Progress in Scientific and Technical Communications, 1968 Annual Report.

ERIC Educational Resources Information Center

Federal Council for Science and Technology, Washington, DC. Committee on Scientific and Technical Information.

This sixth annual report describes progress achieved by the Federal Government in improving the communication of scientific and technical information to support and enhance national science and technology. Included in the report are details regarding the scientific and technical activities of individual Federal Agencies, such as the Atomic Energy…

48 CFR 2452.242-71 - Contract management system.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., concise summary of technical progress made and the costs incurred for each task during the reporting... technical progress made for each task during the reporting period; and (B) Identifies problems, or potential... and progress reporting as described herein. (b) The contract management system shall consist of two...

[Neural prostheses and neuromodulation : Research and clinical practice in therapy and rehabilitation].

PubMed

Stieglitz, T

2010-08-01

Stimulation of the nervous system with the aid of electrical active implants has changed the therapy of neurological diseases and rehabilitation of lost functions and has expanded clinical practice within the last few years. Alleviation of effects of neurodegenerative diseases, therapy of psychiatric diseases, the functional restoration of hearing as well as other applications have been transferred successfully into clinical practice. Other approaches are still under development in preclinical and clinical trials. The restoration of sight by implantable electronic systems that interface with the retina in the eye is an example how technological progress promotes novel medical devices. The idea of using the electrical signal of the brain to control technical devices and (neural) prostheses is driving current research in the field of brain-computer interfaces. The benefit for the patient always has to be balanced with the risks and side effects of those implants in comparison to medicinal and surgical treatments. How these and other developments become established in practice depends finally on their acceptance by the patients and the reimbursement of their costs.

The Unfortunate Human Factor: A Selective History of Human Factors for Technical Communicators.

ERIC Educational Resources Information Center

Johnson, Robert R.

1994-01-01

Reviews moments in the history of human factors that are especially relevant to the field of technical communications. Discusses human factors research that is applicable to technical communications. Focuses on qualitative usability research, minimalism, and human activity interface design. (HB)

ANNUAL REPORT, JULY 1, 1957

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1958-10-31

The progress and trends of research are presented along with a description of operational, service, end administrative activities. Some scientific and technical details are given on research programs in the physical sciences, life sciences, and engineering, however, more complete technical information is available in quarterly progress reports, BNL technical reports, and scientific and technical periodicals. A bibliography of these publications is appended. (For preceding period see BNL-426.) (D.E.B.)

20 CFR 411.180 - What is timely progress toward self-supporting employment?

Code of Federal Regulations, 2010 CFR

2010-04-01

... certificate or vocational or technical training that will enhance your ability to return to work. In addition...-secondary education requirement or vocational or technical training requirement in the applicable progress... this 12-month period; or (iv) You must have been enrolled in a vocational or technical training program...

Service Learning for Engaged Work-Based Learning. Strategies for Transformative Change

ERIC Educational Resources Information Center

Hoffman, D.; Spada, K.; Fox, H. L.

2016-01-01

All 16 Wisconsin Technical College System (WTCS) colleges are committed to creating Intentional Networks Transforming Effective and Rigorous Facilitation of Assessment, Collaboration, and Education (INTERFACE). INTERFACE received a Round Three TAACCCT grant from the U.S. Department of Labor. INTERFACE is a strategic alignment between colleges,…

Organizational Alignment Through Information Technology: A Web-Based Approach to Change

NASA Technical Reports Server (NTRS)

Heinrichs, W.; Smith, J.

1999-01-01

This paper reports on the effectiveness of web-based internet tools and databases to facilitate integration of technical organizations with interfaces that minimize modification of each technical organization.

Adaptive Interfaces

DTIC Science & Technology

1990-11-01

to design and implement an adaptive intelligent interface for a command-and-control-style domain. The primary functionality of the resulting...technical tasks, as follows: 1. Analysis of Current Interface Technologies 2. Dejineation of User Roles 3. Development of User Models 4. Design of Interface...Management Association (FEMA). In the initial version of the prototype, two distin-t user models were designed . One type of user modeled by the system is

Distributed photovoltaic systems: Utility interface issues and their present status

NASA Technical Reports Server (NTRS)

Hassan, M.; Klein, J.

1981-01-01

Major technical issues involving the integration of distributed photovoltaics (PV) into electric utility systems are defined and their impacts are described quantitatively. An extensive literature search, interviews, and analysis yielded information about the work in progress and highlighted problem areas in which additional work and research are needed. The findings from the literature search were used to determine whether satisfactory solutions to the problems exist or whether satisfactory approaches to a solution are underway. It was discovered that very few standards, specifications, or guidelines currently exist that will aid industry in integrating PV into the utility system. Specific areas of concern identified are: (1) protection, (2) stability, (3) system unbalance, (4) voltage regulation and reactive power requirements, (5) harmonics, (6) utility operations, (7) safety, (8) metering, and (9) distribution system planning and design.

Methods for Improving the User-Computer Interface. Technical Report.

ERIC Educational Resources Information Center

McCann, Patrick H.

This summary of methods for improving the user-computer interface is based on a review of the pertinent literature. Requirements of the personal computer user are identified and contrasted with computer designer perspectives towards the user. The user's psychological needs are described, so that the design of the user-computer interface may be…

Evaporation by mechanical vapor recompression. Technical progress report, September 1-December 31, 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iverson, C.H.; Coury, G.E.

1979-01-01

Progress to date in the development of a study of the application of the technologies of mechanical vapor recompression and falling film evaporators as applied to the beet sugar industry is reported. Progress is reported in the following areas: technical literature search and plant visitations of existing applications of VR/FFE.

Open Science Grid (OSG) Ticket Synchronization: Keeping Your Home Field Advantage In A Distributed Environment

NASA Astrophysics Data System (ADS)

Gross, Kyle; Hayashi, Soichi; Teige, Scott; Quick, Robert

2012-12-01

Large distributed computing collaborations, such as the Worldwide LHC Computing Grid (WLCG), face many issues when it comes to providing a working grid environment for their users. One of these is exchanging tickets between various ticketing systems in use by grid collaborations. Ticket systems such as Footprints, RT, Remedy, and ServiceNow all have different schema that must be addressed in order to provide a reliable exchange of information between support entities and users in different grid environments. To combat this problem, OSG Operations has created a ticket synchronization interface called GOC-TX that relies on web services instead of error-prone email parsing methods of the past. Synchronizing tickets between different ticketing systems allows any user or support entity to work on a ticket in their home environment, thus providing a familiar and comfortable place to provide updates without having to learn another ticketing system. The interface is built in a way that it is generic enough that it can be customized for nearly any ticketing system with a web-service interface with only minor changes. This allows us to be flexible and rapidly bring new ticket synchronization online. Synchronization can be triggered by different methods including mail, web services interface, and active messaging. GOC-TX currently interfaces with Global Grid User Support (GGUS) for WLCG, Remedy at Brookhaven National Lab (BNL), and Request Tracker (RT) at the Virtual Data Toolkit (VDT). Work is progressing on the Fermi National Accelerator Laboratory (FNAL) ServiceNow synchronization. This paper will explain the problems faced by OSG and how they led OSG to create and implement this ticket synchronization system along with the technical details that allow synchronization to be preformed at a production level.

25 CFR 30.109 - Will the Secretary provide assistance in developing an alternative AYP definition?

Code of Federal Regulations, 2011 CFR

2011-04-01

... EDUCATION ADEQUATE YEARLY PROGRESS Defining Adequate Yearly Progress Technical Assistance § 30.109 Will the... Bureau, shall provide technical assistance either directly or through contract to the tribal governing...

25 CFR 30.109 - Will the Secretary provide assistance in developing an alternative AYP definition?

Code of Federal Regulations, 2010 CFR

2010-04-01

... EDUCATION ADEQUATE YEARLY PROGRESS Defining Adequate Yearly Progress Technical Assistance § 30.109 Will the... Bureau, shall provide technical assistance either directly or through contract to the tribal governing...

Adsorption of Egg-PC to an Air/Water and Triolein/Water Bubble Interface: Use of the 2-Dimensional Phase Rule to Estimate the Surface Composition of a Phospholipid/Triolein/Water Surface as a Function of Surface Pressure

PubMed Central

Mitsche, Matthew A.; Wang, Libo; Small, Donald M.

2010-01-01

Phospholipid monolayers play a critical role in the structure and stabilization of biological interfaces including all membranes, the alveoli of the lung, fat droplets in adipose tissue, and lipoproteins. The behavior of phospholipids in bilayers and at an air-water interface is well understood. However, the study of phospholipids at oil-water interfaces is limited due to technical challenges. In this study, egg-phosphatidylcholine (EPC) was deposited from small unilamellar vesicles onto a bubble of either air or triolein (TO) formed in a low salt buffer. The surface tension (γ) was measured using a drop tensiometer. We observed that EPC binds irreversibly to both interfaces and at equilibrium exerts ~12 and 15 mN/m of pressure (Π) at an air and TO interface, respectively. After EPC was bound to the interface, the unbound EPC was washed out of the cuvette and the surface was compressed to study the Π/area relationship. To determine the surface concentration (Γ), which cannot be measured directly, compression isotherms from a Langmuir trough and drop tensiometer were compared. The air-water interfaces had identical characteristics using both techniques, thus Γ on the bubble can be determined by overlaying the two isotherms. TO and EPC are both surface active so in a mixed TO/EPC monolayer both molecules will be exposed to water. Since TO is less surface active than EPC, as Π increases the TO is progressively ejected. To understand the Π/area isotherm of EPC on a TO bubble, a variety of TO-EPC mixtures were spread at the air-water interface. The isotherms show an abrupt break in the curve caused by the ejection of TO from the monolayer into a new bulk phase. By overlaying the compression isotherm above the ejection point with a TO bubble compression isotherm, Γ can be estimated. This allows determination of Γ of EPC on a TO bubble as a function of Π. PMID:20151713

Adsorption of egg phosphatidylcholine to an air/water and triolein/water bubble interface: use of the 2-dimensional phase rule to estimate the surface composition of a phospholipid/triolein/water surface as a function of surface pressure.

PubMed

Mitsche, Matthew A; Wang, Libo; Small, Donald M

2010-03-11

Phospholipid monolayers play a critical role in the structure and stabilization of biological interfaces, including all membranes, the alveoli of the lungs, fat droplets in adipose tissue, and lipoproteins. The behavior of phospholipids in bilayers and at an air-water interface is well understood. However, the study of phospholipids at oil-water interfaces is limited due to technical challenges. In this study, egg phosphatidylcholine (EPC) was deposited from small unilamellar vesicles onto a bubble of either air or triolein (TO) formed in a low-salt buffer. The surface tension (gamma) was measured using a drop tensiometer. We observed that EPC binds irreversibly to both interfaces and at equilibrium exerts approximately 12 and 15 mN/m of pressure (Pi) at an air and TO interface, respectively. After EPC was bound to the interface, the unbound EPC was washed out of the cuvette, and the surface was compressed to study the Pi/area relationship. To determine the surface concentration (Gamma), which cannot be measured directly, compression isotherms from a Langmuir trough and drop tensiometer were compared. The air-water interfaces had identical characteristics using both techniques; thus, Gamma on the bubble can be determined by overlaying the two isotherms. Both TO and EPC are surface-active, so in a mixed TO/EPC monolayer, both molecules will be exposed to water. Since TO is less surface-active than EPC, as Pi increases, the TO is progressively ejected. To understand the Pi/area isotherm of EPC on a TO bubble, a variety of TO-EPC mixtures were spread at the air-water interface. The isotherms show an abrupt break in the curve caused by the ejection of TO from the monolayer into a new bulk phase. By overlaying the compression isotherm above the ejection point with a TO bubble compression isotherm, Gamma can be estimated. This allows determination of Gamma of EPC on a TO bubble as a function of Pi.

Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ulm, Franz-Josef

2000-03-31

OAK-B135 Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3(NOTE: Part II A item 1 indicates ''PAPER'', but a report is attached electronically)

Crosscutting Technology Development at the Center for Advanced Separation Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christopher E. Hull

2006-09-30

This Technical Progress Report describes progress made on the twenty nine subprojects awarded in the second year of Cooperative Agreement DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

CROSSCUTTING TECHNOLOGY DEVELOPMENT AT THE CENTER FOR ADVANCED SEPARATION TECHNOLOGIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christopher E. Hull

2006-05-15

This Technical Progress Report describes progress made on the twenty nine subprojects awarded in the second year of Cooperative Agreement DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

The Development and Technical Adequacy of Seventh-Grade Reading Comprehension Measures in a Progress Monitoring Assessment System. Technical Report #1102

ERIC Educational Resources Information Center

Park, Bitnara Jasmine; Alonzo, Julie; Tindal, Gerald

2011-01-01

This technical report describes the process of development and piloting of reading comprehension measures that are appropriate for seventh-grade students as part of an online progress screening and monitoring assessment system, http://easycbm.com. Each measure consists of an original fictional story of approximately 1,600 to 1,900 words with 20…

Human influences on forest ecosystems: the southern wildland-urban interface assessment: summary report

Treesearch

Edward A. Macie; L. Annie Hermansen

2003-01-01

This summary report synthesizes the findings contained in the Southern Wildland-Urban Interface Assessment (General Technical Report SRS-55). The Assessment provides a review of critical wildland-urban interface issues, challenges, and needs for the Southern United States. Topics include population and demographic trends, economic and tax issues, land use planning and...

User Interfaces for Patient-Centered Communication of Health Status and Care Progress

ERIC Educational Resources Information Center

Wilcox-Patterson, Lauren

2013-01-01

The recent trend toward patients participating in their own healthcare has opened up numerous opportunities for computing research. This dissertation focuses on how technology can foster this participation, through user interfaces to effectively communicate personal health status and care progress to hospital patients. I first characterize the…

CMMI (Trademark) for Acquisition, Version 1.2

DTIC Science & Technology

2007-11-01

conjunction with the development of the operational concept to derive more detailed and prec inclu even t . The level of detail of contractual...technical solution, different products or product components ma suppliers. idate Requirem Requirements Ana t the intended operational environment will have...Technical Solutions SP 1.1 Select Technical So SP 1.2 Analyze Selected T SP 1.3 Conduct Technical SG 2 Perform Interface Managemen SP 2.1 Select

Generation and focusing of pulsed intense ion beams. Technical progress report, 1 October 1982 - 30 September, 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hammer, D.A.; Kusse, B.R.; Sudan, R.N.

1983-07-01

The progress on this contract is described in three parts. The first deals with the technical operation of the LION accelerator. The second and third parts are concerned with the experimental results.

Functions and requirements document for interim store solidified high-level and transuranic waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith-Fewell, M.A., Westinghouse Hanford

1996-05-17

The functions, requirements, interfaces, and architectures contained within the Functions and Requirements (F{ampersand}R) Document are based on the information currently contained within the TWRS Functions and Requirements database. The database also documents the set of technically defensible functions and requirements associated with the solidified waste interim storage mission.The F{ampersand}R Document provides a snapshot in time of the technical baseline for the project. The F{ampersand}R document is the product of functional analysis, requirements allocation and architectural structure definition. The technical baseline described in this document is traceable to the TWRS function 4.2.4.1, Interim Store Solidified Waste, and its related requirements, architecture,more » and interfaces.« less

Extending systems ergonomics thinking to accommodate the socio-technical issues of Systems of Systems.

PubMed

Siemieniuch, C E; Sinclair, M A

2014-01-01

Socio-technical issues for Systems of Systems (SoS) differ in several ways from those for systems, mainly because the individual systems that are components of the SoS are usually owned by different organisations, each responsible for the optimisation and operation of its own system. Consequently, management of the SoS is about negotiation and management of the interfaces. Because of issues of Intellectual Property Rights (IPRs), commercial confidence, and the like, there is seldom sufficient, timely information in circulation about the SoS. Surprises are endemic to SoS, and resilience is a fundamental requirement. This paper outlines the different characteristics of SoS compared to ordinary systems, discusses many of the socio-technical issues involved, and then outlines a generic approach to these issues, treating the SoS as a 'wicked problem'. Endemic to this is the need for governance, which is discussed briefly. This is followed by a description of the evident gaps in knowledge about the functioning of SoS, and a listing of tool classes, the development of which would enable progress to be made more effectively. Finally, the paper discusses how the SoS approach might be the best way to entrain ICT to address global drivers, thus pointing to the importance of the SoS approach. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

The DoD Gateway Information System: Bibliography, Directory of Resources, Prototype Experience, [and] User Interface Design.

ERIC Educational Resources Information Center

Cotter, Gladys A.; And Others

The Defense Technical Information Center (DTIC), an organization charged with providing information services to the Department of Defense (DoD) scientific and technical community, actively seeks ways to promote access to and utilization of scientific and technical information (STI) databases, online services, and networks relevant to the conduct…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Kindergarten. Technical Report # 0921

ERIC Educational Resources Information Center

Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in kindergarten. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2008 and administered to approximately 2800 students from…

Carbon nanotube-based multi electrode arrays for neuronal interfacing: progress and prospects

PubMed Central

Bareket-Keren, Lilach; Hanein, Yael

2013-01-01

Carbon nanotube (CNT) coatings have been demonstrated over the past several years as a promising material for neuronal interfacing applications. In particular, in the realm of neuronal implants, CNTs have major advantages owing to their unique mechanical and electrical properties. Here we review recent investigations utilizing CNTs in neuro-interfacing applications. Cell adhesion, neuronal engineering and multi electrode recordings with CNTs are described. We also highlight prospective advances in this field, in particular, progress toward flexible, bio-compatible CNT-based technology. PMID:23316141

Sensor Open System Architecture (SOSA) evolution for collaborative standards development

NASA Astrophysics Data System (ADS)

Collier, Charles Patrick; Lipkin, Ilya; Davidson, Steven A.; Baldwin, Rusty; Orlovsky, Michael C.; Ibrahim, Tim

2017-04-01

The Sensor Open System Architecture (SOSA) is a C4ISR-focused technical and economic collaborative effort between the Air Force, Navy, Army, the Department of Defense (DoD), Industry, and other Governmental agencies to develop (and incorporate) a technical Open Systems Architecture standard in order to maximize C4ISR sub-system, system, and platform affordability, re-configurability, and hardware/software/firmware re-use. The SOSA effort will effectively create an operational and technical framework for the integration of disparate payloads into C4ISR systems; with a focus on the development of a modular decomposition (defining functions and behaviors) and associated key interfaces (physical and logical) for common multi-purpose architecture for radar, EO/IR, SIGINT, EW, and Communications. SOSA addresses hardware, software, and mechanical/electrical interfaces. The modular decomposition will produce a set of re-useable components, interfaces, and sub-systems that engender reusable capabilities. This, in effect, creates a realistic and affordable ecosystem enabling mission effectiveness through systematic re-use of all available re-composed hardware, software, and electrical/mechanical base components and interfaces. To this end, SOSA will leverage existing standards as much as possible and evolve the SOSA architecture through modification, reuse, and enhancements to achieve C4ISR goals. This paper will present accomplishments over the first year of SOSA initiative.

E-Standards For Mass Properties Engineering

NASA Technical Reports Server (NTRS)

Cerro, Jeffrey A.

2008-01-01

A proposal is put forth to promote the concept of a Society of Allied Weight Engineers developed voluntary consensus standard for mass properties engineering. This standard would be an e-standard, and would encompass data, data manipulation, and reporting functionality. The standard would be implemented via an open-source SAWE distribution site with full SAWE member body access. Engineering societies and global standards initiatives are progressing toward modern engineering standards, which become functioning deliverable data sets. These data sets, if properly standardized, will integrate easily between supplier and customer enabling technically precise mass properties data exchange. The concepts of object-oriented programming support all of these requirements, and the use of a JavaTx based open-source development initiative is proposed. Results are reported for activity sponsored by the NASA Langley Research Center Innovation Institute to scope out requirements for developing a mass properties engineering e-standard. An initial software distribution is proposed. Upon completion, an open-source application programming interface will be available to SAWE members for the development of more specific programming requirements that are tailored to company and project requirements. A fully functioning application programming interface will permit code extension via company proprietary techniques, as well as through continued open-source initiatives.

Assessment Program Technical Progress Report, 1996-1997.

ERIC Educational Resources Information Center

McCown, Laurie; Fanning, Erin; Eickmeyer, Barbara

Coconino Community College (CCC) annually assesses its institutional effectiveness to demonstrate its commitment to improving programs and services to students. The 1996-97 Assessment Program Technical Progress Report records the assessment and institutional activities enacted during the academic year, detailing the assessment model, timelines,…

Carbon footprint estimator, phase II : volume I - GASCAP model & volume II - technical appendices [technical brief].

DOT National Transportation Integrated Search

2014-03-01

This study resulted in the development of the GASCAP model (the Greenhouse Gas Assessment : Spreadsheet for Transportation Capital Projects). This spreadsheet model provides a user-friendly interface for determining the greenhouse gas (GHG) emissions...

E-SMART system for in-situ detection of environmental contaminants. Quarterly technical progress report, July--September 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-10-01

General Atomics (GA) leads a team of industrial, academic, and government organizations to develop the Environmental Systems Management, Analysis and Reporting neTwork (E-SMART) for the Defense Advanced Research Project Agency (DARPA), by way of this Technology Reinvestment Project (TRP). E-SMART defines a standard by which networks of smart sensing, sampling, and control devices can interoperate. E-SMART is intended to be an open standard, available to any equipment manufacturer. The user will be provided a standard platform on which a site-specific monitoring plan can be implemented using sensors and actuators from various manufacturers and upgraded as new monitoring devices become commerciallymore » available. This project will further develop and advance the E-SMART standardized network protocol to include new sensors, sampling systems, and graphical user interfaces.« less

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 1. Technical Report # 0919

ERIC Educational Resources Information Center

Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grade 1. These measures, available as part of easyCBM [TM], an online progress monitoring assessment system, were developed in 2008 and administered to approximately 2800 students from schools…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 3. Technical Report # 09-02

ERIC Educational Resources Information Center

Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 2. Technical Report # 0920

ERIC Educational Resources Information Center

Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 5. Technical Report # 09-01

ERIC Educational Resources Information Center

Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 4. Technical Report # 09-03

ERIC Educational Resources Information Center

Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 7. Technical Report 0908

ERIC Educational Resources Information Center

Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 8. Technical Report # 09-04

ERIC Educational Resources Information Center

Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

2009-01-01

In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

RFID Tag as a Sensor - A Review on the Innovative Designs and Applications

NASA Astrophysics Data System (ADS)

Meng, Zhaozong; Li, Zhen

2016-12-01

The Radio Frequency Identification (RFID) technology has gained interests in both academia and industry since its invention. In addition to the applications in access control and supply chain, RFID is also a cost-efficient solution for Non-Destructive Testing (NDT) and pervasive monitoring. The battery free RFID tags are used as independent electromagnetic sensors or energy harvesting and data transmission interface of sensor modules for different measurement purposes. This review paper aims to provide a comprehensive overview of the innovative designs and applications of RFID sensor technology with new insights, identify the technical challenges, and outline the future perspectives. With a brief introduction to the fundamentals of RFID measurement, the enabling technologies and recent technical progress are illustrated, followed by an extensive discussion of the novel designs and applications. Then, based on an in-depth analysis, the potential constraints are identified and the envisaged future directions are suggested, including printable/wearable RFID, System-on-Chip (SoC), ultra-low power, etc. The comprehensive discussion of RFID sensor technology will be inspirational and useful for academic and industrial communities in investigating, developing, and applying RFID for various measurement applications.

Site systems engineering fiscal year 1999 multi-year work plan (MYWP) update for WBS 1.8.2.2

DOE Office of Scientific and Technical Information (OSTI.GOV)

GRYGIEL, M.L.

1998-10-08

Manage the Site Systems Engineering process to provide a traceable integrated requirements-driven, and technically defensible baseline. Through the Site Integration Group(SIG), Systems Engineering ensures integration of technical activities across all site projects. Systems Engineering's primary interfaces are with the RL Project Managers, the Project Direction Office and with the Project Major Subcontractors, as well as with the Site Planning organization. Systems Implementation: (1) Develops, maintains, and controls the site integrated technical baseline, ensures the Systems Engineering interfaces between projects are documented, and maintain the Site Environmental Management Specification. (2) Develops and uses dynamic simulation models for verification of the baselinemore » and analysis of alternatives. (3) Performs and documents fictional and requirements analyses. (4) Works with projects, technology management, and the SIG to identify and resolve technical issues. (5) Supports technical baseline information for the planning and budgeting of the Accelerated Cleanup Plan, Multi-Year Work Plans, Project Baseline Summaries as well as performance measure reporting. (6) Works with projects to ensure the quality of data in the technical baseline. (7) Develops, maintains and implements the site configuration management system.« less

Uranium(IV) Interaction with Aqueous/Solid Interfaces Studied by Nonlinear Optics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geiger, Franz

2015-03-27

This is the Final Technical Report for "Uranium(IV) Interaction with Aqueous/Solid Interfaces Studied by Nonlinear Optics", by Franz M. Geiger, PI, from Northwestern University, IL, USA, Grant Number SC0004101 and/or DE-PS02-ER09-07.

FireWire: Hot New Multimedia Interface or Flash in the Pan?

ERIC Educational Resources Information Center

Learn, Larry L., Ed.

1995-01-01

Examines potential solutions to the problem of personal computer cabling and configuration and serial port performance, namely "FireWire" (P1394) and "Universal Serial Bus" (USB). Discusses interface design, technical capabilities, user friendliness, compatibility, costs, and future perspectives. (AEF)

Probe interface design consideration. [for interplanetary spacecraft missions

NASA Technical Reports Server (NTRS)

Casani, E. K.

1974-01-01

Interface design between a probe and a spacecraft requires not only technical considerations but also management planning and mission analysis interactions. Two further aspects of importance are the flyby versus the probe trade-off, and the relay link design and data handling optimization.

Development and Validation of a Novel Scoring System for Predicting Technical Success of Chronic Total Occlusion Percutaneous Coronary Interventions: The PROGRESS CTO (Prospective Global Registry for the Study of Chronic Total Occlusion Intervention) Score.

PubMed

Christopoulos, Georgios; Kandzari, David E; Yeh, Robert W; Jaffer, Farouc A; Karmpaliotis, Dimitri; Wyman, Michael R; Alaswad, Khaldoon; Lombardi, William; Grantham, J Aaron; Moses, Jeffrey; Christakopoulos, Georgios; Tarar, Muhammad Nauman J; Rangan, Bavana V; Lembo, Nicholas; Garcia, Santiago; Cipher, Daisha; Thompson, Craig A; Banerjee, Subhash; Brilakis, Emmanouil S

2016-01-11

This study sought to develop a novel parsimonious score for predicting technical success of chronic total occlusion (CTO) percutaneous coronary intervention (PCI) performed using the hybrid approach. Predicting technical success of CTO PCI can facilitate clinical decision making and procedural planning. We analyzed clinical and angiographic parameters from 781 CTO PCIs included in PROGRESS CTO (Prospective Global Registry for the Study of Chronic Total Occlusion Intervention) using a derivation and validation cohort (2:1 sampling ratio). Variables with strong association with technical success in multivariable analysis were assigned 1 point, and a 4-point score was developed from summing all points. The PROGRESS CTO score was subsequently compared with the J-CTO (Multicenter Chronic Total Occlusion Registry in Japan) score in the validation cohort. Technical success was 92.9%. On multivariable analysis, factors associated with technical success included proximal cap ambiguity (beta coefficient [b] = 0.88), moderate/severe tortuosity (b = 1.18), circumflex artery CTO (b = 0.99), and absence of "interventional" collaterals (b = 0.88). The resulting score demonstrated good calibration and discriminatory capacity in the derivation (Hosmer-Lemeshow chi-square = 2.633; p = 0.268, and receiver-operator characteristic [ROC] area = 0.778) and validation (Hosmer-Lemeshow chi-square = 5.333; p = 0.070, and ROC area = 0.720) subset. In the validation cohort, the PROGRESS CTO and J-CTO scores performed similarly in predicting technical success (ROC area 0.720 vs. 0.746, area under the curve difference = 0.026, 95% confidence interval = -0.093 to 0.144). The PROGRESS CTO score is a novel useful tool for estimating technical success in CTO PCI performed using the hybrid approach. Copyright © 2016 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

Whither the White Knight: CDROM in Technical Services.

ERIC Educational Resources Information Center

Campbell, Brian

1987-01-01

Outlines evaluative criteria and compares optical data disk products used in library technical processes, including bibliographic records for cataloging, acquisition databases, and local public access catalogs. An extensive table provides information on specific products, including updates, interfaces, edit screens, installation help, manuals,…

Final report : for the period of December 1999 through November 30, 2000 : Florida Transit Training Program (1999/2000) : Florida Technical Assistance Program (1999/2000)

DOT National Transportation Integrated Search

2000-01-01

The following progress report is intended to highlight the significant activities of the Florida Transit Training Program and Florida Technical Assistant Program. The following progress report is intended to highlight the significant activities of th...

Annual progress report : for the period of January 2001 through December 2001 : Florida Transit Training Program (2001) : Florida Technical Assistance Program (2001)

DOT National Transportation Integrated Search

2001-01-01

The following progress report is intended to highlight the significant activities of the Florida Transit Training Program and Florida Technical Assistant Program for the 2001 year. Activities of the Florida Statewide Transit Training Program are pres...

Development of the TACOM (Tank Automotive Command) Thermal Imaging Model (TTIM). Volume 1. Technical Guide and User’s Manual.

DTIC Science & Technology

1984-12-01

BLOCK DATA Default values for variables input by menus. LIBR Interface with frame I/O routines. SNSR Interface with sensor routines. ATMOS Interface with...Routines Included in Frame I/O Interface Routine Description LIBR Selects options for input or output to a data library. FRREAD Reads frame from file and/or...Layer", Journal of Applied Meteorology 20, pp. 242-249, March 1981. 15 L.J. Harding, Numerical Analysis and Applications Software Abstracts, Computing

Glass Fibre/Epoxy Resin Interface Life-Time Prediction.

DTIC Science & Technology

1983-04-01

RD-Ai32 26 GLASS FIBRE /POXY RESIN INTERFACE LIFE-TIME PREDICTION 1/1 (U) BRISTOL UNIV (ENGLAND) H H WILLS PHYSICS LAB K H RSHBEE ET AL. APR 83...D 3005-MS GLASS FIBRE /EPOXY RESIN INTERFACE LIFE-TIME PREDICTION - Final Report by K H G Ashbee, Principal Investigator R Ho~l J P Sargent Elizabeth...REPORT h PERIOD COVERED. Glass Fibre /Epoxy Resin Interface Life-time F-inal Technical 11’ port PreictonApril 1981 - A:’ril 1983 6. PERFORMING ORG. REPORT

Device USB interface and software development for electric parameter measuring instrument

NASA Astrophysics Data System (ADS)

Li, Deshi; Chen, Jian; Wu, Yadong

2003-09-01

Aimed at general devices development, this paper discussed the development of USB interface and software development. With an example, using PDIUSBD12 which support parallel interface, the paper analyzed its technical characteristics. Designed different interface circuit with 80C52 singlechip microcomputer and TMS320C54 series digital signal processor, analyzed the address allocation, register access. According to USB1.1 standard protocol, designed the device software and application layer protocol. The paper designed the data exchange protocol, and carried out system functions.

Comparison of the Booster Interface Temperature in Stainless Steel (SS) V-Channel Versus the Aluminum (Al) Y-Channel Primer Chamber Assemblies (PCAs). Volume 2; Appendices

NASA Technical Reports Server (NTRS)

Garcia, Roberto; Saulsberry, Regor L.

2011-01-01

NASA's Technical Fellow for Propulsion, requested a technical assessment of the performance improvement achieved by the introduction of the stainless steel (SS) V-channel compared to the aluminum (Al) Y-channel Primer Chamber Assembly (PCA) design. The SS V-channel PCA was developed for NASA's Mars Science Laboratory (MSL) Project. The principle focus of the assessment was to measure the transient temperature at the booster interface with both designs. This document contains the Appendices to the Volume I main report.

76 FR 64083 - Reliability Technical Conference; Notice of Technical Conference

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-17

... Technical Conference; Notice of Technical Conference Take notice that the Federal Energy Regulatory Commission will hold a Technical Conference on Tuesday, November 29, 2011, from 1 p.m. to 5 p.m. and... System. The conference will explore the progress made on the priorities for addressing risks to...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2014 CFR

2014-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2014-10-01 2014-10-01 false Preparation of technical...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2012 CFR

2012-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Preparation of technical...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2010 CFR

2010-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Preparation of technical...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2013 CFR

2013-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2013-10-01 2013-10-01 false Preparation of technical...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2011 CFR

2011-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false Preparation of technical...

25 CFR 547.11 - What are the minimum technical standards for money and credit handling?

Code of Federal Regulations, 2010 CFR

2010-04-01

... GAMES § 547.11 What are the minimum technical standards for money and credit handling? This section... interface is: (i) Involved in the play of a game; (ii) In audit mode, recall mode or any test mode; (iii...

25 CFR 547.11 - What are the minimum technical standards for money and credit handling?

Code of Federal Regulations, 2012 CFR

2012-04-01

... GAMES § 547.11 What are the minimum technical standards for money and credit handling? This section... interface is: (i) Involved in the play of a game; (ii) In audit mode, recall mode or any test mode; (iii...

25 CFR 547.11 - What are the minimum technical standards for money and credit handling?

Code of Federal Regulations, 2011 CFR

2011-04-01

... GAMES § 547.11 What are the minimum technical standards for money and credit handling? This section... interface is: (i) Involved in the play of a game; (ii) In audit mode, recall mode or any test mode; (iii...

Solar energy/utility interface - The technical issues

NASA Astrophysics Data System (ADS)

Tabors, R. D.; White, D. C.

1982-01-01

The technical and economic factors affecting an interface between solar/wind power sources and utilities are examined. Photovoltaic, solar thermal, and wind powered systems are subject to stochastic local climatic variations and as such may require full back-up services from utilities, which are then in a position of having reserve generating power and power lines and equipment which are used only part time. The low reliability which has degraded some economies of scale formerly associated with large, centralized power plants, and the lowered rate of the increase in electricity usage is taken to commend the inclusion of power sources with a modular nature such as is available from solar derived electrical generation. Technical issues for maintaining the quality of grid power and also effectively metering purchased and supplied back-up power as part of a homeostatic system of energy control are discussed. It is concluded that economic considerations, rather than technical issues, bear the most difficulty in integrating solar technologies into the utility network.

Technical note: DIRART--A software suite for deformable image registration and adaptive radiotherapy research.

PubMed

Yang, Deshan; Brame, Scott; El Naqa, Issam; Aditya, Apte; Wu, Yu; Goddu, S Murty; Mutic, Sasa; Deasy, Joseph O; Low, Daniel A

2011-01-01

Recent years have witnessed tremendous progress in image guide radiotherapy technology and a growing interest in the possibilities for adapting treatment planning and delivery over the course of treatment. One obstacle faced by the research community has been the lack of a comprehensive open-source software toolkit dedicated for adaptive radiotherapy (ART). To address this need, the authors have developed a software suite called the Deformable Image Registration and Adaptive Radiotherapy Toolkit (DIRART). DIRART is an open-source toolkit developed in MATLAB. It is designed in an object-oriented style with focus on user-friendliness, features, and flexibility. It contains four classes of DIR algorithms, including the newer inverse consistency algorithms to provide consistent displacement vector field in both directions. It also contains common ART functions, an integrated graphical user interface, a variety of visualization and image-processing features, dose metric analysis functions, and interface routines. These interface routines make DIRART a powerful complement to the Computational Environment for Radiotherapy Research (CERR) and popular image-processing toolkits such as ITK. DIRART provides a set of image processing/registration algorithms and postprocessing functions to facilitate the development and testing of DIR algorithms. It also offers a good amount of options for DIR results visualization, evaluation, and validation. By exchanging data with treatment planning systems via DICOM-RT files and CERR, and by bringing image registration algorithms closer to radiotherapy applications, DIRART is potentially a convenient and flexible platform that may facilitate ART and DIR research. 0 2011 Ameri-

REACTOR PHYSICS QUARTERLY REPORT JANUARY, FEBRUARY, MARCH 1970

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmid, L. C.; Clayton, E. D.; Heineman, R. E.

1970-05-01

The objective of the Reactor Physics Quarterly Report is to inform the scientific community in a timely manner of the technical progress made on the many phases of reactor physics work within the laboratory. The report contains brief technical discussions of accomplishments in all areas where significant progress has been made during the quarter.

NASA Docking System (NDS) Users Guide: International Space Station Program. Type 4

NASA Technical Reports Server (NTRS)

Tabakman, Alexander

2010-01-01

The NASA Docking System (NDS) Users Guide provides an overview of the basic information needed to integrate the NDS onto a Host Vehicle (HV). This Users Guide is intended to provide a vehicle developer with a fundamental understanding of the NDS technical and operations information to support their program and engineering integration planning. The Users Guide identifies the NDS Specification, Interface Definition or Requirement Documents that contain the complete technical details and requirements that a vehicle developer must use to design, develop and verify their systems will interface with NDS. This Guide is an initial reference and must not be used as a design document. In the event of conflict between this Users Guide and other applicable interface definition or requirements documents; the applicable document will take precedence. This Users Guide is organized in three main sections. Chapter 1 provides an overview of the NDS and CDA hardware and the operations concepts for the NDS. Chapter 2 provides information for Host Vehicle Program integration with the NDS Project Office. Chapter 2 describes the NDS Project organization, integration and verification processes, user responsibilities, and specification and interface requirement documents. Chapter 3 provides a summary of basic technical information for the NDS design. Chapter 3 includes NDS hardware component descriptions, physical size and weight characteristics, and summary of the capabilities and constraints for the various NDS sub-systems.

The chemistry of cyborgs--interfacing technical devices with organisms.

PubMed

Giselbrecht, Stefan; Rapp, Bastian E; Niemeyer, Christof M

2013-12-23

The term "cyborg" refers to a cybernetic organism, which characterizes the chimera of a living organism and a machine. Owing to the widespread application of intracorporeal medical devices, cyborgs are no longer exclusively a subject of science fiction novels, but technically they already exist in our society. In this review, we briefly summarize the development of modern prosthetics and the evolution of brain-machine interfaces, and discuss the latest technical developments of implantable devices, in particular, biocompatible integrated electronics and microfluidics used for communication and control of living organisms. Recent examples of animal cyborgs and their relevance to fundamental and applied biomedical research and bioethics in this novel and exciting field at the crossroads of chemistry, biomedicine, and the engineering sciences are presented. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Standardized Technical Data Survey (STDS) for Aerial Refueling

DTIC Science & Technology

2016-09-06

the KC-135 and the German Tornado . The tanker/receiver combination was certified by a technical evaluation of the performance interface survey, face...another. That document was first used in assessing the compatibility of the KC-135 and the German Tornado . The survey questions, when accurately answered

Telemetry downlink interfaces and level-zero processing

NASA Technical Reports Server (NTRS)

Horan, S.; Pfeiffer, J.; Taylor, J.

1991-01-01

The technical areas being investigated are as follows: (1) processing of space to ground data frames; (2) parallel architecture performance studies; and (3) parallel programming techniques. Additionally, the University administrative details and the technical liaison between New Mexico State University and Goddard Space Flight Center are addressed.

George A. Olah, Carbocation and Hydrocarbon Chemistry

Science.gov Websites

. Final Technical Report. [HF:BF{sub 2}/H{sub 2}] , DOE Technical Report, 1980 Superacid Catalyzed Coal Conversion Chemistry. 1st and 2nd Quarterly Technical Progress Reports, September 1, 1983-March 30, 1984 , DOE Technical Report, 1984 Superacid Catalyzed Coal Conversion Chemistry. Final Technical Report

Modeling the impacts of climate change and technical progress on the wheat yield in inland China: An autoregressive distributed lag approach.

PubMed

Zhai, Shiyan; Song, Genxin; Qin, Yaochen; Ye, Xinyue; Lee, Jay

2017-01-01

This study aims to evaluate the impacts of climate change and technical progress on the wheat yield per unit area from 1970 to 2014 in Henan, the largest agricultural province in China, using an autoregressive distributed lag approach. The bounded F-test for cointegration among the model variables yielded evidence of a long-run relationship among climate change, technical progress, and the wheat yield per unit area. In the long run, agricultural machinery and fertilizer use both had significantly positive impacts on the per unit area wheat yield. A 1% increase in the aggregate quantity of fertilizer use increased the wheat yield by 0.19%. Additionally, a 1% increase in machine use increased the wheat yield by 0.21%. In contrast, precipitation during the wheat growth period (from emergence to maturity, consisting of the period from last October to June) led to a decrease in the wheat yield per unit area. In the short run, the coefficient of the aggregate quantity of fertilizer used was negative. Land size had a significantly positive impact on the per unit area wheat yield in the short run. There was no significant short-run or long-run impact of temperature on the wheat yield per unit area in Henan Province. The results of our analysis suggest that climate change had a weak impact on the wheat yield, while technical progress played an important role in increasing the wheat yield per unit area. The results of this study have implications for national and local agriculture policies under climate change. To design well-targeted agriculture adaptation policies for the future and to reduce the adverse effects of climate change on the wheat yield, climate change and technical progress factors should be considered simultaneously. In addition, adaptive measures associated with technical progress should be given more attention.

Modeling the impacts of climate change and technical progress on the wheat yield in inland China: An autoregressive distributed lag approach

PubMed Central

Qin, Yaochen; Lee, Jay

2017-01-01

This study aims to evaluate the impacts of climate change and technical progress on the wheat yield per unit area from 1970 to 2014 in Henan, the largest agricultural province in China, using an autoregressive distributed lag approach. The bounded F-test for cointegration among the model variables yielded evidence of a long-run relationship among climate change, technical progress, and the wheat yield per unit area. In the long run, agricultural machinery and fertilizer use both had significantly positive impacts on the per unit area wheat yield. A 1% increase in the aggregate quantity of fertilizer use increased the wheat yield by 0.19%. Additionally, a 1% increase in machine use increased the wheat yield by 0.21%. In contrast, precipitation during the wheat growth period (from emergence to maturity, consisting of the period from last October to June) led to a decrease in the wheat yield per unit area. In the short run, the coefficient of the aggregate quantity of fertilizer used was negative. Land size had a significantly positive impact on the per unit area wheat yield in the short run. There was no significant short-run or long-run impact of temperature on the wheat yield per unit area in Henan Province. The results of our analysis suggest that climate change had a weak impact on the wheat yield, while technical progress played an important role in increasing the wheat yield per unit area. The results of this study have implications for national and local agriculture policies under climate change. To design well-targeted agriculture adaptation policies for the future and to reduce the adverse effects of climate change on the wheat yield, climate change and technical progress factors should be considered simultaneously. In addition, adaptive measures associated with technical progress should be given more attention. PMID:28950027

Supply Chain Sustainability Analysis of Whole Algae Hydrothermal Liquefaction and Upgrading

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pegallapati, Ambica Koushik; Dunn, Jennifer B.; Frank, Edward D.

2015-04-01

The Department of Energy's Bioenergy Technology Office (BETO) collaborates with a wide range of institutions towards the development and deployment of biofuels and bioproducts. To facilitate this effort, BETO and its partner national laboratories develop detailed techno-economic assessments (TEA) of biofuel production technologies as part of the development of design cases and state of technology (SOT) analyses. A design case is a TEA that outlines a target case for a particular biofuel pathway. It enables preliminary identification of data gaps and research and development needs and provides goals and targets against which technology progress is assessed. On the other hand,more » an SOT analysis assesses progress within and across relevant technology areas based on actual experimental results relative to technical targets and cost goals from design cases and includes technical, economic, and environmental criteria as available. (SOT) analyses. A design case is a TEA that outlines a target case for a particular biofuel pathway. It enables preliminary identification of data gaps and research and development needs and provides goals and targets against which technology progress is assessed. On the other hand, an SOT analysis assesses progress within and across relevant technology areas based on actual experimental results relative to technical targets and cost goals from design cases and includes technical, economic, and environmental criteria as available. (SOT) analyses. A design case is a TEA that outlines a target case for a particular biofuel pathway. It enables preliminary identification of data gaps and research and development needs and provides goals and targets against which technology progress is assessed. On the other hand, an SOT analysis assesses progress within and across relevant technology areas based on actual experimental results relative to technical targets and cost goals from design cases and includes technical, economic, and environmental criteria as available.« less

Performance and Reliability of Bonded Interfaces for High-Temperature Packaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeVoto, Douglas

2016-06-08

This is a technical review of the DOE VTO EDT project EDT063, Performance and Reliability of Bonded Interfaces for High-Temperature Packaging. A procedure for analyzing the reliability of sintered-silver through experimental thermal cycling and crack propagation modeling has been outlined and results have been presented.

Flywheel energy storage for electromechanical actuation systems

NASA Technical Reports Server (NTRS)

Hockney, Richard L.; Goldie, James H.; Kirtley, James L.

1991-01-01

The authors describe a flywheel energy storage system designed specifically to provide load-leveling for a thrust vector control (TVC) system using electromechanical actuators (EMAs). One of the major advantages of an EMA system over a hydraulic system is the significant reduction in total energy consumed during the launch profile. Realization of this energy reduction will, however, require localized energy storage capable of delivering the peak power required by the EMAs. A combined flywheel-motor/generator unit which interfaces directly to the 20-kHz power bus represents an ideal candidate for this load leveling. The overall objective is the definition of a flywheel energy storage system for this application. The authors discuss progress on four technical objectives: (1) definition of the specifications for the flywheel-motor/generator system, including system-level trade-off analysis; (2) design of the flywheel rotor; (3) design of the motor/generator; and (4) determination of the configuration for the power management system.

The Promise of Neurotechnology in Clinical Translational Science.

PubMed

White, Susan W; Richey, John A; Gracanin, Denis; Bell, Martha Ann; LaConte, Stephen; Coffman, Marika; Trubanova, Andrea; Kim, Inyoung

2015-09-01

Neurotechnology is broadly defined as a set of devices used to understand neural processes and applications that can potentially facilitate the brain's ability to repair itself. In the past decade, an increasingly explicit understanding of basic biological mechanisms of brain-related illnesses has produced applications that allow a direct yet noninvasive method to index and manipulate the functioning of the human nervous system. Clinical scientists are poised to apply this technology to assess, treat, and better understand complex socioemotional processes that underlie many forms of psychopathology. In this review, we describe the potential benefits and hurdles, both technical and methodological, of neurotechnology in the context of clinical dysfunction. We also offer a framework for developing and evaluating neurotechnologies that is intended to expedite progress at the nexus of clinical science and neural interface designs by providing a comprehensive vocabulary to describe the necessary features of neurotechnology in the clinic.

The Promise of Neurotechnology in Clinical Translational Science

PubMed Central

White, Susan W.; Richey, John A.; Gracanin, Denis; Bell, Martha Ann; LaConte, Stephen; Coffman, Marika; Trubanova, Andrea; Kim, Inyoung

2014-01-01

Neurotechnology is broadly defined as a set of devices used to understand neural processes and applications that can potentially facilitate the brain’s ability to repair itself. In the past decade, an increasingly explicit understanding of basic biological mechanisms of brain-related illnesses has produced applications that allow a direct yet noninvasive method to index and manipulate the functioning of the human nervous system. Clinical scientists are poised to apply this technology to assess, treat, and better understand complex socioemotional processes that underlie many forms of psychopathology. In this review, we describe the potential benefits and hurdles, both technical and methodological, of neurotechnology in the context of clinical dysfunction. We also offer a framework for developing and evaluating neurotechnologies that is intended to expedite progress at the nexus of clinical science and neural interface designs by providing a comprehensive vocabulary to describe the necessary features of neurotechnology in the clinic. PMID:26504676

Heterogeneity of the gut microbiome in mice: guidelines for optimizing experimental design.

PubMed

Laukens, Debby; Brinkman, Brigitta M; Raes, Jeroen; De Vos, Martine; Vandenabeele, Peter

2016-01-01

Targeted manipulation of the gut flora is increasingly being recognized as a means to improve human health. Yet, the temporal dynamics and intra- and interindividual heterogeneity of the microbiome represent experimental limitations, especially in human cross-sectional studies. Therefore, rodent models represent an invaluable tool to study the host-microbiota interface. Progress in technical and computational tools to investigate the composition and function of the microbiome has opened a new era of research and we gradually begin to understand the parameters that influence variation of host-associated microbial communities. To isolate true effects from confounding factors, it is essential to include such parameters in model intervention studies. Also, explicit journal instructions to include essential information on animal experiments are mandatory. The purpose of this review is to summarize the factors that influence microbiota composition in mice and to provide guidelines to improve the reproducibility of animal experiments. © FEMS 2015.

E-SMART system for in-situ detection of environmental contaminants. Quarterly technical progress report, April--June 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-08-01

General Atomics (GA) leads a team of industrial, academic, and government organizations in the development of the Environmental Systems Management, Analysis and Reporting neTwork (E-SMART) for the Defense Advanced Research Project Agency (DARPA), by way of this Technology Reinvestment Project (TRP). E-SMART defines a standard by which networks of smart sensing, sampling, and control devices can interoperate. E-SMART is intended to be an open standard, available to any equipment manufacturer. The user will be provided a standard platform on which a site-specific monitoring plan can be implemented using sensors and actuators from various manufacturers and upgraded as new monitoring devicesmore » become commercially available. This project will further develop and advance the E-SMART standardized network protocol to include new sensors, sampling systems, and graphical user interfaces.« less

Flywheel energy storage for electromechanical actuation systems

NASA Astrophysics Data System (ADS)

Hockney, Richard L.; Goldie, James H.; Kirtley, James L.

The authors describe a flywheel energy storage system designed specifically to provide load-leveling for a thrust vector control (TVC) system using electromechanical actuators (EMAs). One of the major advantages of an EMA system over a hydraulic system is the significant reduction in total energy consumed during the launch profile. Realization of this energy reduction will, however, require localized energy storage capable of delivering the peak power required by the EMAs. A combined flywheel-motor/generator unit which interfaces directly to the 20-kHz power bus represents an ideal candidate for this load leveling. The overall objective is the definition of a flywheel energy storage system for this application. The authors discuss progress on four technical objectives: (1) definition of the specifications for the flywheel-motor/generator system, including system-level trade-off analysis; (2) design of the flywheel rotor; (3) design of the motor/generator; and (4) determination of the configuration for the power management system.

Heterogeneity of the gut microbiome in mice: guidelines for optimizing experimental design

PubMed Central

Laukens, Debby; Brinkman, Brigitta M.; Raes, Jeroen; De Vos, Martine; Vandenabeele, Peter

2015-01-01

Targeted manipulation of the gut flora is increasingly being recognized as a means to improve human health. Yet, the temporal dynamics and intra- and interindividual heterogeneity of the microbiome represent experimental limitations, especially in human cross-sectional studies. Therefore, rodent models represent an invaluable tool to study the host–microbiota interface. Progress in technical and computational tools to investigate the composition and function of the microbiome has opened a new era of research and we gradually begin to understand the parameters that influence variation of host-associated microbial communities. To isolate true effects from confounding factors, it is essential to include such parameters in model intervention studies. Also, explicit journal instructions to include essential information on animal experiments are mandatory. The purpose of this review is to summarize the factors that influence microbiota composition in mice and to provide guidelines to improve the reproducibility of animal experiments. PMID:26323480

Study of a Tracking and Data Acquisition System (TDAS) in the 1990's

NASA Technical Reports Server (NTRS)

1981-01-01

Progress in concept definition studies, operational assessments, and technology demonstrations for the Tracking and Data Acquisition System (TDAS) is reported. The proposed TDAS will be the follow-on to the Tracking and Data Relay Satellite System and will function as a key element of the NASA End-to-End Data System, providing the tracking and data acquisition interface between user accessible data ports on Earth and the user's spaceborne equipment. Technical activities of the "spacecraft data system architecture' task and the "communication mission model' task are emphasized. The objective of the first task is to provide technology forecasts for sensor data handling, navigation and communication systems, and estimate corresponding costs. The second task is concerned with developing a parametric description of the required communication channels. Other tasks with significant activity include the "frequency plan and radio interference model' and the "Viterbi decoder/simulator study'.

Economic analysis of standard interface modules for use with the multi-mission spacecraft, volume 1

NASA Technical Reports Server (NTRS)

1976-01-01

A preliminary technical and economic feasibility study was made of the use of Standardized Interstate Modules (SIM) to perform electual interfacing functions that were historically incorporated into sensors. Sensor interface functions that are capable of standardization from the set of missions planned for the NASA Multi-Mission Spacecraft (MMS) in the 1981 to 1985 time period were identified. The cost savings that could be achieved through the replacement of nonstandard sensor interface flight hardware that might be used in these missions with SIM were examined.

A Braille Interface to the Texas Instruments SR-52 Programmable Calculator.

DTIC Science & Technology

1976-09-21

F / _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ AD—A039 US PENNSYLVANIA STATE UNIV JNIVtRSITY PARK APPLIED RESE——ETc F/G 9/2 * BRAILLE INTERFACE to PC TEXAS...UNCLASSiFIED A BRAILLE INTERFACE TO THE TEXAS INSTRUMENTS SR-52 PR0CRA)*~ABLE CALCULATOR C. P~ JANOTA Technical Memorandum D D C File No. TM 76-244 i...SUPPLEMENTARY NOTES ~~~~ ~ 15. KEY WORDS (ConUnti. on ,.v.ra• .Id. If nøc....ry and td~n t tf y by block ntanb.r) AIDS TO HANDICAPPED BRAILLE INTERFACE

Technical Adequacy of Growth Estimates from a Computer Adaptive Test: Implications for Progress Monitoring

ERIC Educational Resources Information Center

Van Norman, Ethan R.; Nelson, Peter M.; Parker, David C.

2017-01-01

Computer adaptive tests (CATs) hold promise to monitor student progress within multitiered systems of support. However, the relationship between how long and how often data are collected and the technical adequacy of growth estimates from CATs has not been explored. Given CAT administration times, it is important to identify optimal data…

Education, Industrialization and Technical Progress in Mexico. IIEP Research Report No. 6.

ERIC Educational Resources Information Center

Padua, Jorge

This report attempts to analyze the contributions of the educational system and job training programs to industrialization and technical progress in the Conubal zone of the Lower Balsas River of Mexico. The first of the study's three sections consists of two chapters that provide general background. Chapter 1, "Theories of Development and the…

Technical Adequacy and Acceptability of Curriculum-Based Measurement and the Measures of Academic Progress

ERIC Educational Resources Information Center

January, Stacy-Ann A.; Ardoin, Scott P.

2015-01-01

Curriculum-based measurement in reading (CBM-R) and the Measures of Academic Progress (MAP) are assessment tools widely employed for universal screening in schools. Although a large body of research supports the validity of CBM-R, limited empirical evidence exists supporting the technical adequacy of MAP or the acceptability of either measure for…

Annual Technical Progress Report for Emergency School Assistance Program, Title 45, 1970-71.

ERIC Educational Resources Information Center

Lindsey, Randall B.

This paper presents a technical progress report of two programs conducted with funds provided under the Emergency School Assistance Program. One, the Mobile Learning Unit, said to have been designed to measure changes in fourth and fifth grade students' self-concept in a reorganized desegregated school environment, focuses on whether a positive…

Third Progress and Information Report of the Vocational-Technical Education Consortium of States.

ERIC Educational Resources Information Center

Lee, Connie W.; And Others

This description of major activities and accomplishments of the Vocational-Technical Education Consortium of the States (V-TECS) since the second progress report of May, 1975, is designed to provide the reader with a basic understanding of the processes and procedures used by the consortium in achieving its major goal: The production of catalogs…

A PSFI-based analysis on the energy efficiency potential of China’s domestic passenger vehicles

NASA Astrophysics Data System (ADS)

Chen, Chuan; Ren, Huanhuan; Zhao, Dongchang

2017-01-01

In this article, China’s domestic passenger vehicles (excluding new energy vehicles) are categorized into two groups: local brand vehicles and vehicles manufactured by joint ventures. Performance-Size-Fuel economy Index (PSFI) will be applied to analyse the speed of technical progress and the future trends of these vehicles. In addition, a forecast on energy efficiency potential of domestic passenger vehicles from 2016 to 2020 will be made based on different Emphasis on Reducing Fuel Consumption (ERFC) scenarios. According to the study, if the process of technical progress continues at its current speed, domestic ICE passenger vehicles will hardly meet Phase IV requirements by 2020 even though companies contribute as much technical progress to fuel consumption reduction as possible.

Advanced Thermal Emission Imaging Systems Definition and Development

NASA Technical Reports Server (NTRS)

Blasius, Karl; Nava, David (Technical Monitor)

2002-01-01

Santa Barbara Remote Sensing (SBRS), Raytheon Company, is pleased to submit this quarterly progress report of the work performed in the third quarter of Year 2 of the Advanced THEMIS Project, July through September 2002. We review here progress in the proposed tasks. During July through September 2002 progress was made in two major tasks, Spectral Response Characterization and Flight Instrument Definition. Because of staffing problems and technical problems earlier in the program we have refocused the remaining time and budget on the key technical tasks. Current technical problems with a central piece of test equipment has lead us to request a 1 quarter extension to the period of performance. This request is being made through a separate letter independent of this report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stout, D.K.

Flaws are noted in equilibrium growth models which ignore the facts that labor is no longer homogeneous, national governments can no longer guarantee a managed demand, and technical progress is not an independent force. The pace of technical progress is the major variable and increases with competition and certainty in the growth of demand. The outlook for technical progress is examined in the context of productivity, using microprocessor development for illustration. The author takes an optimistic view of new developments in that they do not bring the self-destructive possibility of overpopulation, irreversible damage to the environment, or nuclear war anymore » closer, while having a positive chance to promote a more rewarding relationship between education, work, and life style. The opportunities for positive humanistic changes through microprocessing are confirmed. (DCK)« less

Definition of common support equipment and space station interface requirements for IOC model technology experiments

NASA Technical Reports Server (NTRS)

Russell, Richard A.; Waiss, Richard D.

1988-01-01

A study was conducted to identify the common support equipment and Space Station interface requirements for the IOC (initial operating capabilities) model technology experiments. In particular, each principal investigator for the proposed model technology experiment was contacted and visited for technical understanding and support for the generation of the detailed technical backup data required for completion of this study. Based on the data generated, a strong case can be made for a dedicated technology experiment command and control work station consisting of a command keyboard, cathode ray tube, data processing and storage, and an alert/annunciator panel located in the pressurized laboratory.

Program Management Tool

NASA Technical Reports Server (NTRS)

Gawadiak, Yuri; Wong, Alan; Maluf, David; Bell, David; Gurram, Mohana; Tran, Khai Peter; Hsu, Jennifer; Yagi, Kenji; Patel, Hemil

2007-01-01

The Program Management Tool (PMT) is a comprehensive, Web-enabled business intelligence software tool for assisting program and project managers within NASA enterprises in gathering, comprehending, and disseminating information on the progress of their programs and projects. The PMT provides planning and management support for implementing NASA programmatic and project management processes and requirements. It provides an online environment for program and line management to develop, communicate, and manage their programs, projects, and tasks in a comprehensive tool suite. The information managed by use of the PMT can include monthly reports as well as data on goals, deliverables, milestones, business processes, personnel, task plans, monthly reports, and budgetary allocations. The PMT provides an intuitive and enhanced Web interface to automate the tedious process of gathering and sharing monthly progress reports, task plans, financial data, and other information on project resources based on technical, schedule, budget, and management criteria and merits. The PMT is consistent with the latest Web standards and software practices, including the use of Extensible Markup Language (XML) for exchanging data and the WebDAV (Web Distributed Authoring and Versioning) protocol for collaborative management of documents. The PMT provides graphical displays of resource allocations in the form of bar and pie charts using Microsoft Excel Visual Basic for Application (VBA) libraries. The PMT has an extensible architecture that enables integration of PMT with other strategic-information software systems, including, for example, the Erasmus reporting system, now part of the NASA Integrated Enterprise Management Program (IEMP) tool suite, at NASA Marshall Space Flight Center (MSFC). The PMT data architecture provides automated and extensive software interfaces and reports to various strategic information systems to eliminate duplicative human entries and minimize data integrity issues among various NASA systems that impact schedules and planning.

Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol. 11, No. 1--Vol. 17, No. 6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cottrell, W.B.; Klein, A.

1977-02-23

This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970), through Vol. 17, No. 6 (Nov.-Dec. 1976). The index includes a chronological list of articles (including abstract) followed by KWIC and Author Indexes. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 350 technical articles in the last six years of publication.

HOPE information system review

NASA Astrophysics Data System (ADS)

Suzuki, Yoshiaki; Nishiyama, Kenji; Ono, Shuuji; Fukuda, Kouin

1992-08-01

An overview of the review conducted on H-2 Orbiting Plane (HOPE) is presented. A prototype model was constructed by inputting various technical information proposed by related laboratories. Especially operation flow which enables understanding of correlation between various analysis items, judgement criteria, technical data, and interfaces with others was constructed. Technical information data base and retrieval systems were studied. A Macintosh personal computer was selected for information shaping because of its excellent function, performance, operability, and software completeness.

Circumventing Graphical User Interfaces in Chemical Engineering Plant Design

ERIC Educational Resources Information Center

Romey, Noel; Schwartz, Rachel M.; Behrend, Douglas; Miao, Peter; Cheung, H. Michael; Beitle, Robert

2007-01-01

Graphical User Interfaces (GUIs) are pervasive elements of most modern technical software and represent a convenient tool for student instruction. For example, GUIs are used for [chemical] process design software (e.g., CHEMCAD, PRO/II and ASPEN) typically encountered in the senior capstone course. Drag and drop aspects of GUIs are challenging for…

Performance and Reliability of Bonded Interfaces for High-Temperature Packaging; NREL (National Renewable Energy Laboratory)

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeVoto, Douglas

2015-06-10

This is a technical review of the DOE VTO EDT project EDT063, Performance and Reliability of Bonded Interfaces for High-Temperature Packaging. A procedure for analyzing the reliability of sintered-silver through experimental thermal cycling and crack propagation modeling has been outlined and results have been presented.

78 FR 79434 - Notice of Technical Conference

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-30

...: one that will allow EQR users to file through a web interface on the Commission's Web site, and a... the conference, staff will demonstrate how to make a filing using both the XML and web interface... Calendar of Events on the Commission's Web site, www.ferc.gov . A free webcast of the conference will be...

The development of a prototype intelligent user interface subsystem for NASA's scientific database systems

NASA Technical Reports Server (NTRS)

Campbell, William J.; Roelofs, Larry H.; Short, Nicholas M., Jr.

1987-01-01

The National Space Science Data Center (NSSDC) has initiated an Intelligent Data Management (IDM) research effort which has as one of its components the development of an Intelligent User Interface (IUI).The intent of the latter is to develop a friendly and intelligent user interface service that is based on expert systems and natural language processing technologies. The purpose is to support the large number of potential scientific and engineering users presently having need of space and land related research and technical data but who have little or no experience in query languages or understanding of the information content or architecture of the databases involved. This technical memorandum presents prototype Intelligent User Interface Subsystem (IUIS) using the Crustal Dynamics Project Database as a test bed for the implementation of the CRUDDES (Crustal Dynamics Expert System). The knowledge base has more than 200 rules and represents a single application view and the architectural view. Operational performance using CRUDDES has allowed nondatabase users to obtain useful information from the database previously accessible only to an expert database user or the database designer.

[Address Given at the Regional Junior College Recreation Education Institute, American River College, September 25, 1969.

ERIC Educational Resources Information Center

Lutzin, Sidney G.

The United States has made striking technical advances in recent years, but there has not been comparable progress in social services. Greater affluence and leisure for some have been one result of technical progress, but problems of poverty and urban development are more pressing. New developments to improve the condition of society can be…

THE DEVELOPMENT OF PRE-VOCATIONAL EDUCATION LITERACY COURSES FOR USE WITH COMPUTER ASSISTED INSTRUCTION OF DISADVANTAGED YOUTH AND ADULTS. TECHNICAL PROGRESS REPORT.

ERIC Educational Resources Information Center

HANKIN, EDWARD K.; AND OTHERS

THIS TECHNICAL PROGRESS REPORT COVERS THE FIRST THREE MONTHS OF A PROJECT TO DEVELOP COMPUTER ASSISTED PREVOCATIONAL READING AND ARITHMETIC COURSES FOR DISADVANTAGED YOUTHS AND ADULTS. DURING THE FIRST MONTH OF OPERATION, PROJECT PERSONNEL CONCENTRATED ON SUCH ADMINISTRATIVE MATTERS AS TRAINING STAFF AND PREPARING FACILITIES. AN ARITHMETIC PROGRAM…

Generation and focusing of pulsed intense ion beams. Technical progress report, 20 August 1981-30 September 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hammer, D.A.; Kusse, B.R.; Sudan, R.N.

1983-07-01

The progress on this contract is described in two parts. The first deals with the technical operation of the LION accelerator which is the exact equivalent to one line of PBFA-I. The second part is concerned with the experimental results on the ion diode mounted at the front end of the LION accelerator.

Project LIFE--Language Improvement to Facilitate Education. (Technical Progress Report; Third Quarter; March 1, 1974-May 31, 1974).

ERIC Educational Resources Information Center

National Foundation for the Improvement of Education, Washington, DC.

Reported is the third quarter, fiscal year 1974 (March 1, 1974-May 31, 1974) technical progress of Project LIFE (Language Improvement to Facilitate Education), toward developing an instructional system in which filmstrips in the areas of perceptual training, perceptual thinking, and language/reading are used to assist hearing impaired children in…

Development of an Open Building Automation System Specification Based on ANSI/ASHRAE 135-2004 (BACnet(R) Communications Protocol: A Technical Assessment

DTIC Science & Technology

2007-02-01

on/off control), trending and trend reports, load shedding/load manage- ment, remote setpoint adjustment, initial diagnosis of a service call and...building-specific operational data such as on/off scheduling com- mands, setpoints , and outside air temperature. With help from several other agencies and...interface for monitoring 3. Provide one interface for device/system management/configuration 4. ( Optimally ) provide one interface for device

Development of an Open Building Automation System Specification Based on ANSI/ASHRAE 135-2004 (BACnet(Registered) Communications Protocol): A Technical Assessment

DTIC Science & Technology

2007-02-01

on/off control), trending and trend reports, load shedding/load manage- ment, remote setpoint adjustment, initial diagnosis of a service call and...building-specific operational data such as on/off scheduling com- mands, setpoints , and outside air temperature. With help from several other agencies and...interface for monitoring 3. Provide one interface for device/system management/configuration 4. ( Optimally ) provide one interface for device

The Design of an Interface to a Programming System and MENUNIX: A Menu-Based Interface to UNIX (User Manual). Two Papers in Cognitive Engineering. Technical Report No. 8105.

ERIC Educational Resources Information Center

Perlman, Gary

This report consists of two papers on MENUNIX, an experimental interface to the approximately 300 programs and files available on the Berkeley UNIX 4.0 version of the UNIX operating system. The first paper discusses some of the psychological concerns involved in the design of MENUNIX; the second is a tutorial user manual for MENUNIX, in which the…

The Technical School: College and University Interface in Teaching Fiber, Textile, and Polymer Chemistry

ERIC Educational Resources Information Center

Roberts, Carleton W.

1973-01-01

Discusses the present status of technician and technology-oriented institutions and the two curricula offered by the Textile Department, Clemson University. Indicates that technical school, junior college, and community college graduates are allowed to complete formal training to the four-year degree level in the Clemson program. (CC)

Knowledge-based graphical interfaces for presenting technical information

NASA Technical Reports Server (NTRS)

Feiner, Steven

1988-01-01

Designing effective presentations of technical information is extremely difficult and time-consuming. Moreover, the combination of increasing task complexity and declining job skills makes the need for high-quality technical presentations especially urgent. We believe that this need can ultimately be met through the development of knowledge-based graphical interfaces that can design and present technical information. Since much material is most naturally communicated through pictures, our work has stressed the importance of well-designed graphics, concentrating on generating pictures and laying out displays containing them. We describe APEX, a testbed picture generation system that creates sequences of pictures that depict the performance of simple actions in a world of 3D objects. Our system supports rules for determining automatically the objects to be shown in a picture, the style and level of detail with which they should be rendered, the method by which the action itself should be indicated, and the picture's camera specification. We then describe work on GRIDS, an experimental display layout system that addresses some of the problems in designing displays containing these pictures, determining the position and size of the material to be presented.

User interface development

NASA Technical Reports Server (NTRS)

Aggrawal, Bharat

1994-01-01

This viewgraph presentation describes the development of user interfaces for OS/2 versions of computer codes for the analysis of seals. Current status, new features, work in progress, and future plans are discussed.

Thermal Integration of a Liquid Acquisition Device into a Cryogenic Feed System

NASA Technical Reports Server (NTRS)

Hastings, L. J.; Bolshinskiy, L. G.; Schunk, R. G.; Martin, A. K.; Eskridge, R. H.; Frenkel, A.; Grayson, G.; Pendleton, M. L.

2011-01-01

Primary objectives of this effort were to define the following: (1) Approaches for quantification of the accumulation of thermal energy within a capillary screen liquid acquisition device (LAD) for a lunar lander upper stage during periods of up to 210 days on the lunar surface, (2) techniques for mitigating heat entrapment, and (3) perform initial testing, data evaluation. The technical effort was divided into the following categories: (1) Detailed thermal modeling of the LAD/feed system interactions using both COMSOL computational fluid device and standard codes, (2) FLOW-3D modeling of bulk liquid to provide interfacing conditions for the LAD thermal modeling, (3) condensation conditioning of capillary screens to stabilize surface tension retention capability, and (4) subscale testing of an integrated LAD/feed system. Substantial progress was achieved in the following technical areas: (1) Thermal modeling and experimental approaches for evaluating integrated cryogen LAD/feed systems, at both the system and component levels, (2) reduced gravity pressure control analyses, (3) analytical modeling and testing for capillary screen conditioning using condensation and wicking, and (4) development of rapid turnaround testing techniques for evaluating LAD/feed system thermal and fluid integration. A comprehensive effort, participants included a diverse cross section of representatives from academia, contractors, and multiple Marshall Space Flight Center organizations.

Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ulm, Franz-Josef

2000-06-30

OAK-B135 Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 4. The analysis of the effect of cracks on the acceleration of the calcium leaching process of cement-based materials has been pursued. During the last period (Technical Progress Report No 3), we have introduced a modeling accounting for the high diffusivity of fractures in comparison with the weak solid material diffusivity. It has been shown through dimensional and asymptotic analysis that small fractures do not significantly accelerate the material aging process. This important result for the overall structural aging kinetics of containment structure has beenmore » developed in a paper submitted to the international journal ''Transport in Porous Media''.« less

Conceptual Design of a Space-Based Multimegawatt MHD Power System, Task 1 Topical Report; Volume 1: Technical Discussion

DTIC Science & Technology

1988-01-01

system requirements, design guidelines, and interface requirements has been prepared and included as Volume II of this Task 1 topical report. The Volume ...WAESD-TR-88-0002 Conceptual Design Of A Space-Based Multimegawatt MHD Power System ffA«kjjjjjTfc Task 1 Topical Report Volume I: Technical...Space-Based Multimegawatt MHD Power System: Task 1 Topical Report, Volume I: Technical Discussion Personal Author: Dana, RA. Corporate Author Or

Database interfaces on NASA's heterogeneous distributed database system

NASA Technical Reports Server (NTRS)

Huang, S. H. S.

1986-01-01

The purpose of the ORACLE interface is to enable the DAVID program to submit queries and transactions to databases running under the ORACLE DBMS. The interface package is made up of several modules. The progress of these modules is described below. The two approaches used in implementing the interface are also discussed. Detailed discussion of the design of the templates is shown and concluding remarks are presented.

Deep Space Network (DSN), Network Operations Control Center (NOCC) computer-human interfaces

NASA Technical Reports Server (NTRS)

Ellman, Alvin; Carlton, Magdi

1993-01-01

The technical challenges, engineering solutions, and results of the NOCC computer-human interface design are presented. The use-centered design process was as follows: determine the design criteria for user concerns; assess the impact of design decisions on the users; and determine the technical aspects of the implementation (tools, platforms, etc.). The NOCC hardware architecture is illustrated. A graphical model of the DSN that represented the hierarchical structure of the data was constructed. The DSN spacecraft summary display is shown. Navigation from top to bottom is accomplished by clicking the appropriate button for the element about which the user desires more detail. The telemetry summary display and the antenna color decision table are also shown.

Department of Clinical Investigation Annual Research Progress Report, Fiscal Year 1984. Volume 1,

DTIC Science & Technology

1984-10-01

on a low dosage of medication . Technical Approach: None. Progress: The placebo has not been received from the company. Since the drug company...determine the effect of high dose Ar-C intensification therapy on the -. incidence of CNS relapse. - Technical Approach: All patients with a new...Enrolled to Date: 7 Date of Periodic Review Results Objective(s): To determine the incidence of

GUIDON-WATCH: A Graphic Interface for Viewing a Knowledge-Based System. Technical Report #14.

ERIC Educational Resources Information Center

Richer, Mark H.; Clancey, William J.

This paper describes GUIDON-WATCH, a graphic interface that uses multiple windows and a mouse to allow a student to browse a knowledge base and view reasoning processes during diagnostic problem solving. The GUIDON project at Stanford University is investigating how knowledge-based systems can provide the basis for teaching programs, and this…

Software Engineering for User Interfaces. Technical Report.

ERIC Educational Resources Information Center

Draper, Stephen W.; Norman, Donald A.

The discipline of software engineering can be extended in a natural way to deal with the issues raised by a systematic approach to the design of human-machine interfaces. The user should be treated as part of the system being designed and projects should be organized to take into account the current lack of a priori knowledge of user interface…

Topographica: Building and Analyzing Map-Level Simulations from Python, C/C++, MATLAB, NEST, or NEURON Components

PubMed Central

Bednar, James A.

2008-01-01

Many neural regions are arranged into two-dimensional topographic maps, such as the retinotopic maps in mammalian visual cortex. Computational simulations have led to valuable insights about how cortical topography develops and functions, but further progress has been hindered by the lack of appropriate tools. It has been particularly difficult to bridge across levels of detail, because simulators are typically geared to a specific level, while interfacing between simulators has been a major technical challenge. In this paper, we show that the Python-based Topographica simulator makes it straightforward to build systems that cross levels of analysis, as well as providing a common framework for evaluating and comparing models implemented in other simulators. These results rely on the general-purpose abstractions around which Topographica is designed, along with the Python interfaces becoming available for many simulators. In particular, we present a detailed, general-purpose example of how to wrap an external spiking PyNN/NEST simulation as a Topographica component using only a dozen lines of Python code, making it possible to use any of the extensive input presentation, analysis, and plotting tools of Topographica. Additional examples show how to interface easily with models in other types of simulators. Researchers simulating topographic maps externally should consider using Topographica's analysis tools (such as preference map, receptive field, or tuning curve measurement) to compare results consistently, and for connecting models at different levels. This seamless interoperability will help neuroscientists and computational scientists to work together to understand how neurons in topographic maps organize and operate. PMID:19352443

Technical Note: DIRART – A software suite for deformable image registration and adaptive radiotherapy research

PubMed Central

Yang, Deshan; Brame, Scott; El Naqa, Issam; Aditya, Apte; Wu, Yu; Murty Goddu, S.; Mutic, Sasa; Deasy, Joseph O.; Low, Daniel A.

2011-01-01

Purpose: Recent years have witnessed tremendous progress in image guide radiotherapy technology and a growing interest in the possibilities for adapting treatment planning and delivery over the course of treatment. One obstacle faced by the research community has been the lack of a comprehensive open-source software toolkit dedicated for adaptive radiotherapy (ART). To address this need, the authors have developed a software suite called the Deformable Image Registration and Adaptive Radiotherapy Toolkit (DIRART). Methods:DIRART is an open-source toolkit developed in MATLAB. It is designed in an object-oriented style with focus on user-friendliness, features, and flexibility. It contains four classes of DIR algorithms, including the newer inverse consistency algorithms to provide consistent displacement vector field in both directions. It also contains common ART functions, an integrated graphical user interface, a variety of visualization and image-processing features, dose metric analysis functions, and interface routines. These interface routines make DIRART a powerful complement to the Computational Environment for Radiotherapy Research (CERR) and popular image-processing toolkits such as ITK. Results: DIRART provides a set of image processing∕registration algorithms and postprocessing functions to facilitate the development and testing of DIR algorithms. It also offers a good amount of options for DIR results visualization, evaluation, and validation. Conclusions: By exchanging data with treatment planning systems via DICOM-RT files and CERR, and by bringing image registration algorithms closer to radiotherapy applications, DIRART is potentially a convenient and flexible platform that may facilitate ART and DIR research. PMID:21361176

Techniques and applications for binaural sound manipulation in human-machine interfaces

NASA Technical Reports Server (NTRS)

Begault, Durand R.; Wenzel, Elizabeth M.

1990-01-01

The implementation of binaural sound to speech and auditory sound cues (auditory icons) is addressed from both an applications and technical standpoint. Techniques overviewed include processing by means of filtering with head-related transfer functions. Application to advanced cockpit human interface systems is discussed, although the techniques are extendable to any human-machine interface. Research issues pertaining to three-dimensional sound displays under investigation at the Aerospace Human Factors Division at NASA Ames Research Center are described.

Techniques and applications for binaural sound manipulation in human-machine interfaces

NASA Technical Reports Server (NTRS)

Begault, Durand R.; Wenzel, Elizabeth M.

1992-01-01

The implementation of binaural sound to speech and auditory sound cues (auditory icons) is addressed from both an applications and technical standpoint. Techniques overviewed include processing by means of filtering with head-related transfer functions. Application to advanced cockpit human interface systems is discussed, although the techniques are extendable to any human-machine interface. Research issues pertaining to three-dimensional sound displays under investigation at the Aerospace Human Factors Division at NASA Ames Research Center are described.

Total Factor Productivity Growth, Technical Progress & Efficiency Change in Vietnam Coal Industry - Nonparametric Approach

NASA Astrophysics Data System (ADS)

Phuong, Vu Hung

2018-03-01

This research applies Data Envelopment Analysis (DEA) approach to analyze Total Factor Productivity (TFP) and efficiency changes in Vietnam coal mining industry from 2007 to 2013. The TFP of Vietnam coal mining companies decreased due to slow technological progress and unimproved efficiency. The decadence of technical efficiency in many enterprises proved that the coal mining industry has a large potential to increase productivity through technical efficiency improvement. Enhancing human resource training, technology and research & development investment could help the industry to improve efficiency and productivity in Vietnam coal mining industry.

Scientific and Technical Information and Transfer for Education (STITE). Research Report No. 1.

ERIC Educational Resources Information Center

Zunde, Pranas

STITE (Scientific and Technical Information Transfer for Education) is basically a system to interface between science information and the science learner. As such STITE acts as a link between STIC (Science and Technology Information Centers) and LIS (Learning Information Systems). After an introduction to the goals and objectives of the ongoing…

Vocational-Technical Education Interface with Ohio's High Technology Business and Industrial Sector. Final Report.

ERIC Educational Resources Information Center

McCormick, Robert W.

This study explored the relationship of vocational-technical educational institutions in Ohio with business and industry using high-technology applications. The study attempted to determine what high-technology applications will be adopted by Ohio's business and industry in the next 5 years, what experience the schools have had in working with…

Student-Centered and Dynamic Interfaces that Enrich Technical Learning for Online Science Learners: A Review of the Literature

ERIC Educational Resources Information Center

Killian, Susan A.; Beck, Dennis E.; O'Bryan, Corliss A.; Jarvis, Nathan; Clausen, Edgar C.; Crandall, Philip G.

2014-01-01

Communicating complex scientific and technical information presents a challenge for food science educators. The most efficient learning occurs when all senses are engaged, one reason that many educators believe that scientific principles are best taught with hands-on laboratory experiences. Today there are many challenges to the continuation of…

Lightning Protection Guidelines for Aerospace Vehicles

NASA Technical Reports Server (NTRS)

Goodloe, C. C.

1999-01-01

This technical memorandum provides lightning protection engineering guidelines and technical procedures used by the George C. Marshall Space Flight Center (MSFC) Electromagnetics and Aerospace Environments Branch for aerospace vehicles. The overviews illustrate the technical support available to project managers, chief engineers, and design engineers to ensure that aerospace vehicles managed by MSFC are adequately protected from direct and indirect effects of lightning. Generic descriptions of the lightning environment and vehicle protection technical processes are presented. More specific aerospace vehicle requirements for lightning protection design, performance, and interface characteristics are available upon request to the MSFC Electromagnetics and Aerospace Environments Branch, mail code EL23.

Screening mechanisms at polar oxide heterointerfaces

DOE PAGES

Hong, Seungbum; Nakhmanson, Serge M.; Fong, Dillon D.

2016-06-16

The interfaces of polar oxide heterostructures can display electronic properties unique from the oxides they border, as they require screening from either internal or external sources of charge. The screening mechanism depends on a variety of factors, including the band structure at the interface, the presence of point defects or adsorbates, whether or not the oxide is ferroelectric, and whether or not an external field is applied. In this review, we discuss both theoretical and experimental aspects of different screening mechanisms, giving special emphasis to ways in which the mechanism can be altered to provide novel or tunable functionalities. Wemore » begin with a theoretical introduction to the problem and highlight recent progress in understanding the impact of point defects on polar interfaces. Different case studies are then discussed, for both the high thickness regime, where interfaces must be screened and each interface can be considered separately, and the low thickness regime, where the degree and nature of screening can be manipulated and the interfaces are close enough to interact. As a result, we end with a brief outlook toward new developments in this rapidly progressing field.« less

Standardization of quantum technologies and QKD activities within ETSI (Conference Presentation)

NASA Astrophysics Data System (ADS)

Lenhart, Gaby

2016-04-01

In order to establish new ICT technologies successfully on the market it is essential to build trust within any potential users. This is especially true for technologies which are based upon paradigms that are not yet familiar to these users, such as quantum technologies. Technical standards are an excellent means to offer a certain degree of legal reliability and technical interoperability that is required by industry for commercial take up. While such standards on the one hand must be clear enough to provide strict rules for implementers, on the other hand they also must remain flexible enough to not restrict progress in further research and development on the standardized technology. Hence such standards have to be produced by a wide variety of stakeholders taking into account all their different needs. The paper will provide some insight into the general mechanisms of standardization and their relation to quantum technologies. Alongside with the relevance of standardization as an enabler for certification of quantum based technologies it will explain its potential for securing intellectual property. In its first part paper will concentrate on the advantages of standardization and discuss fears some of the stakeholders share, in detail. The second part will focus on the technical work going on in ETSI in relation to quantum technologies. In 2008 ETSI created a standards work group on Quantum Key Distribution, the ETSI ISG QKD and more recently a group on Quantum-Safe Cryptography, the ETSI ISG QSC. A significant part of the technical work of these groups has already been published and will be introduced in the following. However a big share of work is still ongoing and lot more is planned for the future, as are continuous revisions and updates of the published specifications. This standardization work covers several levels: It starts of by problem statements in the form of use cases, from which technical requirements can be derived. These requirements then form the base upon which a reference architecture is created. Various different specifications describe in detail components, protocols and interfaces. An ontology is developed in order to guarantee common understanding of the technical terms used in standardization for quantum technologies. Special emphasis is provided to security proofs.

48 CFR 2011.104-70 - NRC Clauses.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Technical Reports, when deliverables include a technical report. (b) The contracting officer shall insert the clause at 2052.211-71 Technical Progress Report, in all solicitations and contracts except— (1...) The contracting officer shall insert the clause at 2052.211-72 Financial Status Report, in applicable...

48 CFR 2011.104-70 - NRC Clauses.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Technical Reports, when deliverables include a technical report. (b) The contracting officer shall insert the clause at 2052.211-71 Technical Progress Report, in all solicitations and contracts except— (1...) The contracting officer shall insert the clause at 2052.211-72 Financial Status Report, in applicable...

48 CFR 2011.104-70 - NRC Clauses.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Technical Reports, when deliverables include a technical report. (b) The contracting officer shall insert the clause at 2052.211-71 Technical Progress Report, in all solicitations and contracts except— (1...) The contracting officer shall insert the clause at 2052.211-72 Financial Status Report, in applicable...

48 CFR 2011.104-70 - NRC Clauses.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Technical Reports, when deliverables include a technical report. (b) The contracting officer shall insert the clause at 2052.211-71 Technical Progress Report, in all solicitations and contracts except— (1...) The contracting officer shall insert the clause at 2052.211-72 Financial Status Report, in applicable...

48 CFR 2011.104-70 - NRC Clauses.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Technical Reports, when deliverables include a technical report. (b) The contracting officer shall insert the clause at 2052.211-71 Technical Progress Report, in all solicitations and contracts except— (1...) The contracting officer shall insert the clause at 2052.211-72 Financial Status Report, in applicable...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 2 2010-07-01 2010-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 2 2014-07-01 2014-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 2 2013-07-01 2013-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 2 2011-07-01 2011-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 2 2012-07-01 2012-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

How controllers compensate for the lack of flight progress strips.

DOT National Transportation Integrated Search

1996-02-01

The role of the Flight Progress Strip, currently used to display important flight data, has been debated because of long range plans to automate the air traffic control (ATC) human-computer interface. Currently, the Fight Progress Strip is viewed by ...

ISABELLE: a progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hahn, H

This paper discusses the ISABELLE project, which has the objective of constructing a high-energy proton colliding beam facility at Brookhaven National Laboratory. The major technical features of the intersecting storage accelerators with their projected performance are described. Application of over 1000 superconducting magnets in the two rings represents the salient characteristic of the machine. The status of the entire project, the technical progress made so far, and difficulties encountered are reviewed.

Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bender, W.

2013-01-01

Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

Measurement of solids motion in gas-fluidized beds. Technical progress report, 1 October 1982-31 December 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, M.M.; Chao, B.T.

This technical progress report covers the progress made during the fifth quarter of the project entitled Measurements of Solids Motion in Gas Fluidized Beds under Grant No. DOE-F22-81PC40804 during the period 1 October through 31 December 1982. The research concerns the measurement of solids particle velocity distribution and residence time distribution using the Computer-Aided Particle Tracking Facility (CAPTF) at the University of Illinois at Urbana-Champaign. The experimental equipment and measuring methods used to determine particle size distribution and particle motion and the results obtained are presented.

Ecological Interface Design for Computer Network Defense.

PubMed

Bennett, Kevin B; Bryant, Adam; Sushereba, Christen

2018-05-01

A prototype ecological interface for computer network defense (CND) was developed. Concerns about CND run high. Although there is a vast literature on CND, there is some indication that this research is not being translated into operational contexts. Part of the reason may be that CND has historically been treated as a strictly technical problem, rather than as a socio-technical problem. The cognitive systems engineering (CSE)/ecological interface design (EID) framework was used in the analysis and design of the prototype interface. A brief overview of CSE/EID is provided. EID principles of design (i.e., direct perception, direct manipulation and visual momentum) are described and illustrated through concrete examples from the ecological interface. Key features of the ecological interface include (a) a wide variety of alternative visual displays, (b) controls that allow easy, dynamic reconfiguration of these displays, (c) visual highlighting of functionally related information across displays, (d) control mechanisms to selectively filter massive data sets, and (e) the capability for easy expansion. Cyber attacks from a well-known data set are illustrated through screen shots. CND support needs to be developed with a triadic focus (i.e., humans interacting with technology to accomplish work) if it is to be effective. Iterative design and formal evaluation is also required. The discipline of human factors has a long tradition of success on both counts; it is time that HF became fully involved in CND. Direct application in supporting cyber analysts.

Bigger data for big data: from Twitter to brain-computer interfaces.

PubMed

Roesch, Etienne B; Stahl, Frederic; Gaber, Mohamed Medhat

2014-02-01

We are sympathetic with Bentley et al.'s attempt to encompass the wisdom of crowds in a generative model, but posit that a successful attempt at using big data will include more sensitive measurements, more varied sources of information, and will also build from the indirect information available through technology, from ancillary technical features to data from brain-computer interfaces.

The 1996 NAEP Technical Report.

ERIC Educational Resources Information Center

Allen, Nancy L.; Carlson, James E.; Zelenak, Christine A.

This report documents the design, administration, and data analysis procedure of the National Assessment of Education Progress (NAEP) for 1996. It indicates the technical decisions that were made and the rationale behind them. Detailed substantive findings are not presented in this report. These chapters provide technical information about the…

Distributed photovoltaic systems - Addressing the utility interface issues

NASA Astrophysics Data System (ADS)

Firstman, S. I.; Vachtsevanos, G. J.

This paper reviews work conducted in the United States on the impact of dispersed photovoltaic sources upon utility operations. The photovoltaic (PV) arrays are roof-mounted on residential houses and connected, via appropriate power conditioning equipment, to the utility grid. The presence of such small (4-6 Kw) dispersed generators on the distribution network raises questions of a technical, economic and institutional nature. After a brief identification of utility interface issues, the paper addresses such technical concerns as protection of equipment and personnel safety, power quality and utility operational stability. A combination of experimental and analytical approaches has been adopted to arrive at solutions to these problems. Problem areas, under various PV system penetration scenarios, are identified and conceptual designs of protection and control equipment and operating policies are developed so that system reliability is maintained while minimizing capital costs. It is hoped that the resolution of balance-of-system and grid interface questions will ascertain the economic viability of photovoltaic systems and assist in their widespread utilization in the future.

Lincoln County nuclear waste project. Quarterly progress report, October 1, 1991--December 31, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-03-01

This document included the following three progress reports to the Yucca Mountain Project Office on radioactive waste storage in Lincoln County, Nevada: financial status report; federal cash transactions report; and technical progress report.

Lincoln County nuclear waste project. Quarterly progress report, January 1, 1992--March 31, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-03-01

This document included the following three progress reports to the Yucca Mountain Project Office on radioactive waste storage in Lincoln County, Nevada: financial status report; federal cash transactions report; and technical progress report.

Lincoln County nuclear waste project quarterly progress report, April 1, 1992--June 30, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-03-01

This document included the following three progress reports to the Yucca Mountain Project Office on radioactive waste storage in Lincoln County, Nevada: financial status report; federal cash transactions report; and technical progress report.

The Technology Information Environment with Industry{trademark} system description

DOE Office of Scientific and Technical Information (OSTI.GOV)

Detry, R.; Machin, G.

The Technology Information Environment with Industry (TIE-In{trademark}) provides users with controlled access to distributed laboratory resources that are packaged in intelligent user interfaces. These interfaces help users access resources without requiring the user to have technical or computer expertise. TIE-In utilizes existing, proven technologies such as the Kerberos authentication system, X-Windows, and UNIX sockets. A Front End System (FES) authenticates users and allows them to register for resources and subsequently access them. The FES also stores status and accounting information, and provides an automated method for the resource owners to recover costs from users. The resources available through TIE-In aremore » typically laboratory-developed applications that are used to help design, analyze, and test components in the nation`s nuclear stockpile. Many of these applications can also be used by US companies for non-weapons-related work. TIE-In allows these industry partners to obtain laboratory-developed technical solutions without requiring them to duplicate the technical resources (people, hardware, and software) at Sandia.« less

Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author, Volume 18 (1) through Volume 22 (6)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cottrell, W.B.; Passiakos, M.

This index to Nuclear Safety covers articles published in Nuclear Safety, Volume 18, Number 1 (January-February 1977) through Volume 22, Number 6 (November-December 1981). The index is divided into three section: a chronological list of articles (including abstracts), a permuted-title (KWIC) index, and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. Over 300 technical articles published in Nuclear Safety in the last 5 years are listed in this index.

Effective properties of dispersed phase reinforced composite materials with perfect and imperfect interfaces

NASA Astrophysics Data System (ADS)

Han, Ru

This thesis focuses on the analysis of dispersed phase reinforced composite materials with perfect as well as imperfect interfaces using the Boundary Element Method (BEM). Two problems of interest are considered, namely, to determine the limitations in the use of effective properties and the analysis of failure progression at the inclusion-matrix interface. The effective moduli (effective Young's modulus, effective Poisson's ratio, effective shear modulus, and effective bulk modulus) of composite materials can be determined at the mesoscopic level using three-dimensional parallel BEM simulations. By comparing the mesoscopic BEM results and the macroscopic results based on effective properties, limitations in the effective property approach can be determined. Decohesion is an important failure mode associated with fiber-reinforced composite materials. Analysis of failure progression at the fiber-matrix interface in fiber-reinforced composite materials is considered using a softening decohesion model consistent with thermodynamic concepts. In this model, the initiation of failure is given directly by a failure criterion. Damage is interpreted by the development of a discontinuity of displacement. The formulation describing the potential development of damage is governed by a discrete decohesive constitutive equation. Numerical simulations are performed using the direct boundary element method. Incremental decohesion simulations illustrate the progressive evolution of debonding zones and the propagation of cracks along the interfaces. The effect of decohesion on the macroscopic response of composite materials is also investigated.

A New Animal Model for Developing a Somatosensory Neural Interface for Prosthetic Limbs

DTIC Science & Technology

2008-02-12

interface for neuroprosthetic limbs . PI: Douglas J. Weber, Ph.D. University of Pittsburgh 1 10/15/2007 Scientific progress and accomplishments. We...information to the brain. A new animal model for developing a somatosensory neural interface for neuroprosthetic limbs . PI: Douglas J. Weber, Ph.D...A new animal model for developing a somatosensory neural interface for neuroprosthetic limbs . PI: Douglas J. Weber, Ph.D. University of Pittsburgh

77 FR 16250 - Notice of Proposed Information Collection for Public Comment; Office of Native American Programs...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-20

... Information Collection for Public Comment; Office of Native American Programs (ONAP) Training and Technical... subject proposal. The data required by Office of Native American Programs Training and Technical... progress. The data identifies needs, outputs and outcomes of the training and technical assistance. DATES...

Quantitative biological surface science: challenges and recent advances.

PubMed

Höök, Fredrik; Kasemo, Bengt; Grunze, Michael; Zauscher, Stefan

2008-12-23

Biological surface science is a broad, interdisciplinary subfield of surface science, where properties and processes at biological and synthetic surfaces and interfaces are investigated, and where biofunctional surfaces are fabricated. The need to study and to understand biological surfaces and interfaces in liquid environments provides sizable challenges as well as fascinating opportunities. Here, we report on recent progress in biological surface science that was described within the program assembled by the Biomaterial Interface Division of the Science and Technology of Materials, Interfaces and Processes (www.avs.org) during their 55th International Symposium and Exhibition held in Boston, October 19-24, 2008. The selected examples show that the rapid progress in nanoscience and nanotechnology, hand-in-hand with theory and simulation, provides increasingly sophisticated methods and tools to unravel the mechanisms and details of complex processes at biological surfaces and in-depth understanding of biomolecular surface interactions.

Numerical Simulation of Polysilicon Solid-liquid Interface Transmogrification in Heat Transfer Process

NASA Astrophysics Data System (ADS)

Yang, Xi; Ma, Wenhui; Lv, Guoqiang; Zhang, Mingyu

2018-01-01

The shape of solid-liquid interface during the directional solidification process, which is difficult to be observed and measured in actual processes, controls the grain orientation and grain size of polysilicon ingot. We carried out numerical calculations of the directional solidification progress of polycrystalline silicon and invested the means to deal with the latent heat of solidification in numerical simulation. The distributions of the temperature field of the melt for the crystallization progress as well as the transformation of the solid-liquid interface were obtained. The simulation results are consistent with the experimental outcomes. The results show that the curvature of solid-liquid interface is small and stability, larger grain sized columnar crystal can be grown in the laboratory-scale furnace at a solidification rate of 10 μm•s-1. It shall provide important theoretical basis for metallurgical process and polysilicon production technology.

Social inequalities in the face of scientific and technological development: an antinomy or an historic problem?

PubMed

Delgado, Guilherme Costa

2017-07-01

This paper aims to conduct a conceptual analysis of the relationship between scientific and technical progress and social equality, or the reduction of inequalities. We examine this relationship by drawing on three theoretical perspectives: 1) ethical economics, championed by classical economic thinkers and centered on utilitarian self-interest, 2) Mainstream theories of economic development espousing the endogenous link between labor productivity growth and technical progress, 3) the critique of theories of economic development that emerged in the second half of the twentieth century, including Celso Furtado's critique of the theory of underdevelopment, emphasizing the prevalence of egalitarian tendencies, and ecological economics, which suggest alternative paths to those set by "classical" theories of development. The fundamental antinomy posed by the title of this article, characterized by an intrinsic contradiction between technical progress and social equality, strictly presupposes the ethical economics perspective, dominated by the social relations that constitute the "social order".

Experimental study of an isochorically heated heterogeneous interface. A progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fernandez, Juan Carlos

2015-08-20

Outline of the presentation: Studying possible mix / interface motion between heterogeneous low/high Z interfaces driven by 2-fluid or kinetic plasma effects (Heated to few eV, Sharp (sub µm) interface); Isochoric heating to initialize interface done with Al quasimonoenergetic ion beams on Trident; Have measured isochoric heating in individual materials intended for compound targets; Fielded experiments on Trident to measure interface motion (Gold-diamond, tin-aluminium); Measured heated-sample temperature with streaked optical pyrometry (SOP) (UT Austin led (research contract), SOP tests → heating uniformity Vs thickness on Al foils. Results are being analyzed.

Concept and implementation of a study dashboard module for a continuous monitoring of trial recruitment and documentation.

PubMed

Toddenroth, Dennis; Sivagnanasundaram, Janakan; Prokosch, Hans-Ulrich; Ganslandt, Thomas

2016-12-01

The difficulty of managing patient recruitment and documentation for clinical trials prompts a demand for instruments for closely monitoring these critical but unpredictable processes. Increasingly adopted Electronic Data Capture (EDC) applications provide novel opportunities to reutilize stored information for an efficient management of traceable trial workflows. In related clinical and administrative settings, so-called digital dashboards that continuously visualize time-dependent parameters have recently met a growing acceptance. To investigate the technical feasibility of a study dashboard for monitoring the progress of patient recruitment and trial documentation, we set out to develop a propositional prototype in the form of a separate software module. After narrowing down functional requirements in semi-structured interviews with study coordinators, we analyzed available interfaces of a locally deployed EDC application, and designed the prototypical study dashboard based on previous findings. The module thereby leveraged a standardized export format in order to extract and import relevant trial data into a clinical data warehouse. Web-based reporting tools then facilitated the definition of diverse views, including diagrams of the progress of patient accrual and form completion at different granularity levels. To estimate the utility of the dashboard and its compatibility with current workflows, we interviewed study coordinators after a demonstration of sample outputs from ongoing trials. The employed tools promoted a rapid development. Displays of the implemented dashboard are organized around an entry page that integrates key metrics for available studies, and which links to more detailed information such as study-specific enrollment per center. The interviewed experts commented that the included graphical summaries appeared suitable for detecting that something was generally amiss, although practical remedies would mostly depend on additional information such as access to the original patient-specific data. The dependency on a separate application was seen as a downside. Interestingly, the prospective users warned that in some situations knowledge of specific accrual statistics might undermine blinding in a subtle yet intricate fashion, so ignorance of certain patient features was seen as sometimes preferable for reproducibility. Our proposed study dashboard graphically recaps key progress indicators of patient accrual and trial documentation. The modular implementation illustrates the technical feasibility of the approach. The use of a study dashboard might introduce certain technical requirements as well as subtle interpretative complexities, which may have to be weighed against potential efficiency gains. Copyright © 2016 Elsevier Inc. All rights reserved.

Space Generic Open Avionics Architecture (SGOAA) reference model technical guide

NASA Technical Reports Server (NTRS)

Wray, Richard B.; Stovall, John R.

1993-01-01

This report presents a full description of the Space Generic Open Avionics Architecture (SGOAA). The SGOAA consists of a generic system architecture for the entities in spacecraft avionics, a generic processing architecture, and a six class model of interfaces in a hardware/software system. The purpose of the SGOAA is to provide an umbrella set of requirements for applying the generic architecture interface model to the design of specific avionics hardware/software systems. The SGOAA defines a generic set of system interface points to facilitate identification of critical interfaces and establishes the requirements for applying appropriate low level detailed implementation standards to those interface points. The generic core avionics system and processing architecture models provided herein are robustly tailorable to specific system applications and provide a platform upon which the interface model is to be applied.

A Connector between Active Laboratory Probes and Computer Interfaces of Different Brands

ERIC Educational Resources Information Center

Hui, Kaleonui J.; Coney, John P.; Binder, P.-M.

2016-01-01

In PASCO's Technical Article #763, it is stated that "PASCO [also] makes sensors with an 8-pin DIN connector. These sensors cannot be used with the Vernier interfaces, as they have different power requirements." Recently we had the need to make such connections in a 10-station freshman lab. Since the Vernier input is a 6-way BT 631A plug…

Integrative Physical and Cognitive Training Development to Better Meet Airman Mission Requirements

DTIC Science & Technology

2015-07-26

Warfighter Interface Division Applied Neuroscience Branch Wright-Patterson AFB OH 45433 711 HPW/RHCP 11. SPONSOR/MONITOR’S REPORT NUMBER(S...Interface Division) and Erica Johnson (AFRL, Applied Neuroscience Branch) for their contributions in technical development and manuscript editing that...Liston C. Hobson J. Stickgold, R. Cognitive flexibility across the sleep–wake cycle: REM-sleep enhancement of anagram problem solving. Cogn Brain

Chips: A Tool for Developing Software Interfaces Interactively.

DTIC Science & Technology

1987-10-01

of the application through the objects on the screen. Chips makes this easy by supplying simple and direct access to the source code and data ...object-oriented programming, user interface management systems, programming environments. Typographic Conventions Technical terms appearing in the...creating an environment in which we could do our work. This project could not have happened without him. Jeff Bonar started and managed the Chips

Multimodal neuroelectric interface development

NASA Technical Reports Server (NTRS)

Trejo, Leonard J.; Wheeler, Kevin R.; Jorgensen, Charles C.; Rosipal, Roman; Clanton, Sam T.; Matthews, Bryan; Hibbs, Andrew D.; Matthews, Robert; Krupka, Michael

2003-01-01

We are developing electromyographic and electroencephalographic methods, which draw control signals for human-computer interfaces from the human nervous system. We have made progress in four areas: 1) real-time pattern recognition algorithms for decoding sequences of forearm muscle activity associated with control gestures; 2) signal-processing strategies for computer interfaces using electroencephalogram (EEG) signals; 3) a flexible computation framework for neuroelectric interface research; and d) noncontact sensors, which measure electromyogram or EEG signals without resistive contact to the body.

User interface issues in supporting human-computer integrated scheduling

NASA Technical Reports Server (NTRS)

Cooper, Lynne P.; Biefeld, Eric W.

1991-01-01

Explored here is the user interface problems encountered with the Operations Missions Planner (OMP) project at the Jet Propulsion Laboratory (JPL). OMP uses a unique iterative approach to planning that places additional requirements on the user interface, particularly to support system development and maintenance. These requirements are necessary to support the concepts of heuristically controlled search, in-progress assessment, and iterative refinement of the schedule. The techniques used to address the OMP interface needs are given.

Preserving the Finger Lakes for the Future: A Prototype Decision Support System for Water Resource Management, Open Space, and Agricultural Protection

NASA Technical Reports Server (NTRS)

Brower, Robert

2003-01-01

As described herein, this project has progressed well, with the initiation or completion of a number of program facets at programmatic, technical, and inter-agency levels. The concept of the Virtual Management Operations Center has taken shape, grown, and has been well received by parties from a wide variety of agencies and organizations in the Finger Lakes region and beyond. As it has evolved in design and functionality, and to better illustrate its current focus for this project, it has been given the expanded name of Watershed Virtual Management Operations Center (W-VMOC). It offers the advanced, compelling functionality of interactive 3D visualization interfaced with 2D mapping, all accessed via Internet or virtually any kind of distributed computer network. This strong foundation will allow the development of a Decision Support System (DSS) with anticipated enhanced functionality to be applied to the myriad issues involved in the wise management of the Finger Lakes region.

Automation for System Safety Analysis

NASA Technical Reports Server (NTRS)

Malin, Jane T.; Fleming, Land; Throop, David; Thronesbery, Carroll; Flores, Joshua; Bennett, Ted; Wennberg, Paul

2009-01-01

This presentation describes work to integrate a set of tools to support early model-based analysis of failures and hazards due to system-software interactions. The tools perform and assist analysts in the following tasks: 1) extract model parts from text for architecture and safety/hazard models; 2) combine the parts with library information to develop the models for visualization and analysis; 3) perform graph analysis and simulation to identify and evaluate possible paths from hazard sources to vulnerable entities and functions, in nominal and anomalous system-software configurations and scenarios; and 4) identify resulting candidate scenarios for software integration testing. There has been significant technical progress in model extraction from Orion program text sources, architecture model derivation (components and connections) and documentation of extraction sources. Models have been derived from Internal Interface Requirements Documents (IIRDs) and FMEA documents. Linguistic text processing is used to extract model parts and relationships, and the Aerospace Ontology also aids automated model development from the extracted information. Visualizations of these models assist analysts in requirements overview and in checking consistency and completeness.

Software metrics: The key to quality software on the NCC project

NASA Technical Reports Server (NTRS)

Burns, Patricia J.

1993-01-01

Network Control Center (NCC) Project metrics are captured during the implementation and testing phases of the NCCDS software development lifecycle. The metrics data collection and reporting function has interfaces with all elements of the NCC project. Close collaboration with all project elements has resulted in the development of a defined and repeatable set of metrics processes. The resulting data are used to plan and monitor release activities on a weekly basis. The use of graphical outputs facilitates the interpretation of progress and status. The successful application of metrics throughout the NCC project has been instrumental in the delivery of quality software. The use of metrics on the NCC Project supports the needs of the technical and managerial staff. This paper describes the project, the functions supported by metrics, the data that are collected and reported, how the data are used, and the improvements in the quality of deliverable software since the metrics processes and products have been in use.

A 3D virtual reality simulator for training of minimally invasive surgery.

PubMed

Mi, Shao-Hua; Hou, Zeng-Gunag; Yang, Fan; Xie, Xiao-Liang; Bian, Gui-Bin

2014-01-01

For the last decade, remarkable progress has been made in the field of cardiovascular disease treatment. However, these complex medical procedures require a combination of rich experience and technical skills. In this paper, a 3D virtual reality simulator for core skills training in minimally invasive surgery is presented. The system can generate realistic 3D vascular models segmented from patient datasets, including a beating heart, and provide a real-time computation of force and force feedback module for surgical simulation. Instruments, such as a catheter or guide wire, are represented by a multi-body mass-spring model. In addition, a realistic user interface with multiple windows and real-time 3D views are developed. Moreover, the simulator is also provided with a human-machine interaction module that gives doctors the sense of touch during the surgery training, enables them to control the motion of a virtual catheter/guide wire inside a complex vascular model. Experimental results show that the simulator is suitable for minimally invasive surgery training.

Designer's unified cost model

NASA Technical Reports Server (NTRS)

Freeman, William T.; Ilcewicz, L. B.; Swanson, G. D.; Gutowski, T.

1992-01-01

A conceptual and preliminary designers' cost prediction model has been initiated. The model will provide a technically sound method for evaluating the relative cost of different composite structural designs, fabrication processes, and assembly methods that can be compared to equivalent metallic parts or assemblies. The feasibility of developing cost prediction software in a modular form for interfacing with state of the art preliminary design tools and computer aided design programs is being evaluated. The goal of this task is to establish theoretical cost functions that relate geometric design features to summed material cost and labor content in terms of process mechanics and physics. The output of the designers' present analytical tools will be input for the designers' cost prediction model to provide the designer with a data base and deterministic cost methodology that allows one to trade and synthesize designs with both cost and weight as objective functions for optimization. The approach, goals, plans, and progress is presented for development of COSTADE (Cost Optimization Software for Transport Aircraft Design Evaluation).

Developments in Technical Education in the British Caribbean, 1940-60.

ERIC Educational Resources Information Center

Pemberton, S. Macpherson

The paper discusses developments in technical education in the British West Indies from 1940-1960 emphasizing the relation between education and economic development. The objective is to analyze the economic basis of progress in technical education. The document is presented in four chapters. Chapter I summarizes historical background prior to…

Programs of Study: Year 2 Joint Technical Report. Research Snapshot

ERIC Educational Resources Information Center

National Research Center for Career and Technical Education, 2010

2010-01-01

In January 2010, the National Research Center for Career and Technical Education (NRCCTE) issued a progress report on three studies being conducted by the Center that examine the implementation and outcomes of Programs of Study (POS), which were required in the 2006 reauthorization of the federal legislation for career and technical education…

RASSP Benchmark 4 Technical Description.

DTIC Science & Technology

1998-01-09

be carried out. Based on results of the study, an implementation of all, or part, of the system described in this benchmark technical description...validate interface and timing constraints. The ISA level of modeling defines the limit of detail expected in the VHDL virtual prototype. It does not...develop a set of candidate architectures and perform an architecture trade-off study. Candidate proces- sor implementations must then be examined for

Research Notes - An Introduction to Openness and Evolvability Assessment

DTIC Science & Technology

2016-08-01

importance of different business and technical characteristics that combine to achieve an open solution. The complexity of most large-scale systems of...process characteristic)  Granularity of the architecture (size of functional blocks)  Modularity (cohesion and coupling)  Support for multiple...Description)  OV-3 (Operational Information Exchange Matrix)  SV-1 (Systems Interface Description)  TV-1 ( Technical Standards Profile). Note that there

Teaching Notes

NASA Astrophysics Data System (ADS)

2001-11-01

Where teachers share ideas and teaching solutions with the wider physics teaching community: contact ped@iop.org. Contents: Technical Trimmings: The ALBA interface and logger Technical Trimmings: A constant velocity apparatus based on Lenz's Law On the Map: Ashfield School: A Technology College Let's Investigate: Microwave frustration Physics on a Shoestring: Variation of pressure with depth Starting Out: First Year Fun! My Way: Grüneisen's law for the classroom Curiosity: Aqua-Magic

Distributed user interfaces for clinical ubiquitous computing applications.

PubMed

Bång, Magnus; Larsson, Anders; Berglund, Erik; Eriksson, Henrik

2005-08-01

Ubiquitous computing with multiple interaction devices requires new interface models that support user-specific modifications to applications and facilitate the fast development of active workspaces. We have developed NOSTOS, a computer-augmented work environment for clinical personnel to explore new user interface paradigms for ubiquitous computing. NOSTOS uses several devices such as digital pens, an active desk, and walk-up displays that allow the system to track documents and activities in the workplace. We present the distributed user interface (DUI) model that allows standalone applications to distribute their user interface components to several devices dynamically at run-time. This mechanism permit clinicians to develop their own user interfaces and forms to clinical information systems to match their specific needs. We discuss the underlying technical concepts of DUIs and show how service discovery, component distribution, events and layout management are dealt with in the NOSTOS system. Our results suggest that DUIs--and similar network-based user interfaces--will be a prerequisite of future mobile user interfaces and essential to develop clinical multi-device environments.

TRU Waste Management Program. Cost/schedule optimization analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Detamore, J.A.; Raudenbush, M.H.; Wolaver, R.W.

This Current Year Work Plan presents in detail a description of the activities to be performed by the Joint Integration Office Rockwell International (JIO/RI) during FY86. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO/RI by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO/RI tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, taskmore » guidance development, task monitoring, task progress information gathering and reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of reports for DOE detailing program status. Program Analysis is performed by the JIO/RI to support identification and assessment of alternatives, and development of long-term TRU waste program capabilities. These analyses include short-term analyses in response to DOE information requests, along with performing an RH Cost/Schedule Optimization report. Systems models will be developed, updated, and upgraded as needed to enhance JIO/RI's capability to evaluate the adequacy of program efforts in various fields. A TRU program data base will be maintained and updated to provide DOE with timely responses to inventory related questions.« less

FY 1986 current fiscal year work plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This Current Year Work Plan presents in detail a description of the activities to be performed by the Joint Integration Office/RI during FY86. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO/RI by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO/RI tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance development, taskmore » monitoring, task progress information gathering and reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of reports for DOE detailing program status. Program Analysis is performed by the JIO/RI to support identification and assessment of alternatives, and development of long-term TRU waste program capabilities. These analyses include short term analyses in response to DOE information requests, along with performing an RH Cost/Schedule Optimization report. System models will be developed, updated, and upgraded as needed to enhance JIO/RI's capability to evaluate the adequacy of program efforts in various fields. A TRU program data base will be maintained and updated to provide DOE with timely responses to inventory related questions.« less

Computational toxicology using the OpenTox application programming interface and Bioclipse

PubMed Central

2011-01-01

Background Toxicity is a complex phenomenon involving the potential adverse effect on a range of biological functions. Predicting toxicity involves using a combination of experimental data (endpoints) and computational methods to generate a set of predictive models. Such models rely strongly on being able to integrate information from many sources. The required integration of biological and chemical information sources requires, however, a common language to express our knowledge ontologically, and interoperating services to build reliable predictive toxicology applications. Findings This article describes progress in extending the integrative bio- and cheminformatics platform Bioclipse to interoperate with OpenTox, a semantic web framework which supports open data exchange and toxicology model building. The Bioclipse workbench environment enables functionality from OpenTox web services and easy access to OpenTox resources for evaluating toxicity properties of query molecules. Relevant cases and interfaces based on ten neurotoxins are described to demonstrate the capabilities provided to the user. The integration takes advantage of semantic web technologies, thereby providing an open and simplifying communication standard. Additionally, the use of ontologies ensures proper interoperation and reliable integration of toxicity information from both experimental and computational sources. Conclusions A novel computational toxicity assessment platform was generated from integration of two open science platforms related to toxicology: Bioclipse, that combines a rich scriptable and graphical workbench environment for integration of diverse sets of information sources, and OpenTox, a platform for interoperable toxicology data and computational services. The combination provides improved reliability and operability for handling large data sets by the use of the Open Standards from the OpenTox Application Programming Interface. This enables simultaneous access to a variety of distributed predictive toxicology databases, and algorithm and model resources, taking advantage of the Bioclipse workbench handling the technical layers. PMID:22075173

4D synchrotron X-ray imaging to understand porosity development in shales during exposure to hydraulic fracturing fluid

NASA Astrophysics Data System (ADS)

Kiss, A. M.; Bargar, J.; Kohli, A. H.; Harrison, A. L.; Jew, A. D.; Lim, J. H.; Liu, Y.; Maher, K.; Zoback, M. D.; Brown, G. E.

2016-12-01

Unconventional (shale) reservoirs have emerged as the most important source of petroleum resources in the United States and represent a two-fold decrease in greenhouse gas emissions compared to coal. Despite recent progress, hydraulic fracturing operations present substantial technical, economic, and environmental challenges, including inefficient recovery, wastewater production and disposal, contaminant and greenhouse gas pollution, and induced seismicity. A relatively unexplored facet of hydraulic fracturing operations is the fluid-rock interface, where hydraulic fracturing fluid (HFF) contacts shale along faults and fractures. Widely used, water-based fracturing fluids contain oxidants and acid, which react strongly with shale minerals. Consequently, fluid injection and soaking induces a host of fluid-rock interactions, most notably the dissolution of carbonates and sulfides, producing enhanced or "secondary" porosity networks, as well as mineral precipitation. The competition between these mechanisms determines how HFF affects reactive surface area and permeability of the shale matrix. The resultant microstructural and chemical changes may also create capillary barriers that can trap hydrocarbons and water. A mechanistic understanding of the microstructure and chemistry of the shale-HFF interface is needed to design new methodologies and fracturing fluids. Shales were imaged using synchrotron micro-X-ray computed tomography before, during, and after exposure to HFF to characterize changes to the initial 3D structure. CT reconstructions reveal how the secondary porosity networks advance into the shale matrix. Shale samples span a range of lithologies from siliceous to calcareous to organic-rich. By testing shales of different lithologies, we have obtained insights into the mineralogic controls on secondary pore network development and the morphologies at the shale-HFF interface and the ultimate composition of produced water from different facies. These results show that mineral texture is a major control over secondary porosity network morphology.

Atmospheric, Magnetospheric and Plasmas in Space (AMPS) spacelab payload definition study. Volume 3: Interface control documents. Part 2: AMPS payload to spacelab ICD

NASA Technical Reports Server (NTRS)

1976-01-01

The AMPS to Spacelab Interface Control Document which is to be used as a guide for format and information content in generating specific AMPS Mission ICDs is presented. This document is meant to supplement the Spacelab Payload Accommodations Handbook in that it only defines interfaces which are not discussed in the handbook to the level required for design purposes. The AMPS Top Level Requirements Tree, illustrates this ICD by a shaded area and its relationship to the other AMPS technical documents. Other interface documents shown are the Level II, AMPS to Space Shuttle Vehicle ICD and the Level III, AMPS to Instruments ICD.

Service offerings and interfaces for the ACTS network of earth stations

NASA Technical Reports Server (NTRS)

Coney, T. A.; Dobyns, T. R.; Chitre, D. M.; Lindstrom, R.

1988-01-01

The NASA Advanced Communications Technology Satellite (ACTS) will use a network of about 20 earth stations to operate as a Mode 1 network. This network will support two ACTS program objectives: to verify the technical performance of ACTS Mode 1 operation in GEO and to demonstrate the types and quality of services that can be provided by an ACTS Mode 1 communications system. The terrestrial interface design is a critical element in assuring that these network earth stations will meet the objectives. In this paper, the applicable terrestrial interface design requirements, the resulting interface specifications, and the associated terrestrial input/output hardware are discussed. A functional block diagram of a network earth station is shown.

Space station automation of common module power management and distribution, volume 2

NASA Technical Reports Server (NTRS)

Ashworth, B.; Riedesel, J.; Myers, C.; Jakstas, L.; Smith, D.

1990-01-01

The new Space Station Module Power Management and Distribution System (SSM/PMAD) testbed automation system is described. The subjects discussed include testbed 120 volt dc star bus configuration and operation, SSM/PMAD automation system architecture, fault recovery and management expert system (FRAMES) rules english representation, the SSM/PMAD user interface, and the SSM/PMAD future direction. Several appendices are presented and include the following: SSM/PMAD interface user manual version 1.0, SSM/PMAD lowest level processor (LLP) reference, SSM/PMAD technical reference version 1.0, SSM/PMAD LLP visual control logic representation's (VCLR's), SSM/PMAD LLP/FRAMES interface control document (ICD) , and SSM/PMAD LLP switchgear interface controller (SIC) ICD.

Proceedings: Computer Science and Data Systems Technical Symposium, volume 1

NASA Technical Reports Server (NTRS)

Larsen, Ronald L.; Wallgren, Kenneth

1985-01-01

Progress reports and technical updates of programs being performed by NASA centers are covered. Presentations in viewgraph form are included for topics in three categories: computer science, data systems and space station applications.

The Biswell symposium: fire issues and solutions in urban interface and wildland ecosystems; February 15-17, 1994; Walnut Creek, California

Treesearch

David R. Weise; Robert E. Martin

1995-01-01

These proceedings summarize the results of a symposium designed to address current issues about wildfire and prescribed fire in both the wildland-urban interface and in wildlands. Thirty-eight invited oral papers and 23 poster papers describing the issues and state-of-the-art solutions to technical, biological, and social challenges currently facing land and fire...

Data management system DIU test system

NASA Technical Reports Server (NTRS)

1976-01-01

An operational and functional description is given of the data management system. Descriptions are included for the test control unit, analog stimulus panel, discrete stimulus panel, and the precision source. The mechanical configuration is defined and illustrated to provide card and component location for modification or repair. The unit level interfaces are mirror images of the DIU interfaces and are described in the Final Technical Report for NASA-MSFC contract NAS8-29155.

TACS Central Control Facility.

DTIC Science & Technology

1981-02-12

PULSE RTC REAL TIME CLOCK -{> I . SIGNAL INVERSION UASC UNIVERSAL ASYNCHRONOUS SERIAL - ---- 4w SPECIAL INTERFACE CONTROLLER Fiq. 2-1. MAC hardware...34 Universal Asynchronous Serial Controller" (UASC) cards. The cards implement an RS-232 standard interface. All controllers are set to operate at a data...Bridwell and I. Richer, "A Preliminary Design of a TDMA System for FLEETSAT," Technical Note 1975-5, Lincoln Laboratory, M.I.T. (12 March 1975), DDC

Technical progress in silicon sheet growth under DOE/JPL FSA program, 1975-1986

NASA Technical Reports Server (NTRS)

Kalejs, J. P.

1986-01-01

The technical progress made in the Silicon Sheet Growth Program during its 11 years was reviewed. At present, in 1986, only two of the original 9 techniques have survived to the start-up, pilot-plant stage in industry. These two techniques are the edge-defined, film-fed growth (EFG) technique that produces closed shape polygons, and the WEB dendritic technique that produces single ribbons. Both the status and future concerns of the EFG and WEB techniques were discussed.

Annual Progress Report (17th) and 1992-97 Renewal Proposal Interactive Graphics for Molecular Studies

DTIC Science & Technology

1991-01-24

Molecular Graphics, vol. 6, No. 4 (Dec. 1988), p. 223. Turk, Greg, "Interactive Collision Detection for Molecular Graphics," M.S. thesis , UNC-Chapel Hill...Problem," Master’s thesis , UNC Department of Computer Science Technical Report #TR87-013, May 1987. Pique, ME., "Technical Trends in Molecular Graphics...AD-A236 598 Seventeenth Annual Progress Report and 1992-97 Renewal Proposal Interactive Graphics for Molecular Studies TR91-020 January 24, 1991 red

Enhanced oil recovery utilizing high-angle wells in the Frontier Formation, Badger Basin Field, Park County, Wyoming. Quarterly technical progress report, 1 March 1993--30 June 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fortmann, R.G.; Walker, J.P.

1993-07-10

Sierra Energy Company`s targeted goals during the third quarter of this Cooperative Agreement included the following objectives from the Statement of Work: in Phase 2A, completion of subtask 2.1.2--acquire best possible field data in the 3-D seismic program; and initiation of Subtask 2.1.3--process acquired 3-D seismic data. Technical progress is described for these tasks.

10 CFR 603.1100 - Contracting officer's post-award responsibilities.

Code of Federal Regulations, 2011 CFR

2011-01-01

... technical progress, financial status, and future program plans. (b) Tracking and processing of reports... progress reports, and patent reports. (c) Handling payment requests and related matters. For a TIA using advance payments, that includes reviews of progress to verify that there is continued justification for...

7 CFR 3402.23 - Documentation of progress on funded projects.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the academic program due to unsatisfactory academic progress; or voluntarily withdraws from the Fellowship or the academic program. If a Fellow has not completed all degree requirements at the end of the... database contains narrative project information, progress/impact statements, and final technical reports...

7 CFR 3402.23 - Documentation of progress on funded projects.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the academic program due to unsatisfactory academic progress; or voluntarily withdraws from the Fellowship or the academic program. If a Fellow has not completed all degree requirements at the end of the... database contains narrative project information, progress/impact statements, and final technical reports...

7 CFR 3402.23 - Documentation of progress on funded projects.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the academic program due to unsatisfactory academic progress; or voluntarily withdraws from the Fellowship or the academic program. If a Fellow has not completed all degree requirements at the end of the... database contains narrative project information, progress/impact statements, and final technical reports...

7 CFR 3402.23 - Documentation of progress on funded projects.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the academic program due to unsatisfactory academic progress; or voluntarily withdraws from the Fellowship or the academic program. If a Fellow has not completed all degree requirements at the end of the... database contains narrative project information, progress/impact statements, and final technical reports...

The Richard C. Schneider Lecture. New dimensions of neurosurgery in the realm of high technology: possibilities, practicalities, realities.

PubMed

Apuzzo, M L

1996-04-01

Fueled by a buoyant economy, popular attitudes and demands, and parallel progress in transferable technical and biological areas, neurosurgery has enjoyed a remarkable quarter of a century of progress. Developmental trends in the discipline have included the following: 1) a refinement of preoperative definition of the structural substrate, 2) miniaturization of operative corridors, 3) reduction of operative trauma, 4) increased effectiveness at the target site, and 5) incorporation of improved technical adjuvants and physical operative tools into treatment protocols. In particular, the computer has become a formidable ally in diagnostic and surgical events. Trends in technical development indicate that we are entering an exciting era of advanced surgery of the human cerebrum, which is heralded by the following: 1) current developments in areas of imaging, sensors, and visualization; 2) new devices for localization and navigation; 3) new capabilities for action at the target point; and 4) innovative concepts related to advanced operative venues. Imaging has provided structurally based surgical maps, which now are being given the new dimension of function in complex and integrated formats for preoperative planning and intraoperative tactical direction. Cerebral localization and navigation based on these advances promise to provide further refinement to the field of stereotactic neurosurgery, as linked systems are superseded by more flexible nonlinked methodologies in functionally defined volume-oriented navigational databases. Target point action now includes not only ablative capabilities through micro-operative methods and the use of stereotactically directed high-energy forms but also the emergence of restorative capabilities through applications of principles of genetic engineering in the areas of molecular and cellular neurosurgery. Complex, dedicated, and self-contained operative venues will be required to optimize the emergence and development of these computer-oriented micro/stereotactic capabilities, which appear to be unavoidably required as locales for the practice and development of virtual reality-based stations for operative rehearsal, simulation, training, and, ultimately, enhancement of operative events through robotic interfaces. Primary impetus for progress has relied upon new combinations of technologies, disciplines, and industries. Philosophical and practical problems include the spectrum of availability of these methods to the population at large, the training of individuals to properly administer these methods, defining the acceptable envelope of expertise, and maintaining suitable delivery and progress while containing spiraling costs. Advanced neurological surgery and the use and development of high-technology adjuvants require a robust economy that has a populace willing to invest in the luxury of such developments. The current socioeconomic situation is fragile from the standpoint of both economics and attitudes of the patients and health care providers, with diversion of economic resources, redistribution of funding bases, modification of patient referrals, practice styles, and service attitudes undermining progress. Economic pressures have brought high-technology methods under great scrutiny regarding their effectiveness and cost-effectiveness. Reform proposals have specifically targeted technology-oriented services, and the Office of Technology Assessment has recommended increasing the use of managed care providers who look to information on cost-effectiveness and clinical practice guidelines to establish efficient management strategies and issue "report cards." Although the premise is laudable and "gimmickry" needs to be identified, it might be argued that such scrutiny and control might be overbearing and overused, impeding appropriate delivery and progress.

NAEP 1999 Long-Term Trend Technical Analysis Report: Three Decades of Student Performance. NCES 2005-484

ERIC Educational Resources Information Center

Allen, Nancy L.; McClellan, Catherine A.; Stoeckel, Joan J.

2005-01-01

This report provides an update to the technical analysis procedures documenting the 1996 National Assessment of Educational Progress (NAEP) as presented in "The NAEP 1996 Technical Report" (Allen, Carlson, and Zelenak, 1999). It describes how the 1999 long-term trend data were incorporated into the trend analyses. Since no national main…

Technical Report Interchange Through Synchronized OAI Caches

NASA Technical Reports Server (NTRS)

Liu, Xiaming; Maly, Kurt; Zubair, Mohammad; Tang, Rong; Padshah, Mohammad Imran; Roncaglia, George; Rocker, JoAnne; Nelson, Michael; vonOfenheim, William; Luce, Richard

2002-01-01

The Technical Report Interchange project is a cooperative experimental effort between NASA Langley Research Center, Los Alamos National Laboratory, Air Force Research Laboratory, Sandia National Laboratory and Old Dominion University to allow for the integration of technical reports. This is accomplished using the Open Archives Initiative Protocol for Metadata Harvesting (OAI-PMH) and having each site cache the metadata from the other participating sites. Each site also implements additional software to ingest the OAI-PMH harvested metadata into their native digital library (DL). This allows the users at each site to see an increased technical report collection through the familiar DL interfaces and tale advantage of whatever valued added are provided by the native DL.

SERENITY Aware Development of Security and Dependability Solutions

NASA Astrophysics Data System (ADS)

Serrano, Daniel; Maña, Antonio; Llarena, Rafael; Crespo, Beatriz Gallego-Nicasio; Li, Keqin

This chapter presents an infrastructure supporting the implementation of Executable Components (ECs). ECs represent S&D solutions at the implementation level, that is, by means of pieces of executable code. ECs are instantiated by the Serenity runtime Framework (SRF) as a result of requests coming from applications. The development of ECs requires programmers having specific technical knowledge about SERENITY, since they need to implement certain interfaces of the ECs according to SERENITY standards. Every EC has to implement, the interface between the SRF and the EC itself, and the interface that the EC offers to applications.

Integrated Maintenance Information System (IMIS): A Maintenance Information Delivery Concept.

DTIC Science & Technology

1987-11-01

InterFace Figure 2. Portable Maintenance Computer Concept. provide advice for difficult fault-isolation problems . The technician will be able to accomplish...faced with an ever-growing number of paper-based technical orders (TOs). This has greatly increased costs and distribution problems . In addition, it has...compounded problems associ- ated with ensuring accurate data and the lengthy correction times involved. To improve the accuracy of technical data and

SUGAR: graphical user interface-based data refiner for high-throughput DNA sequencing.

PubMed

Sato, Yukuto; Kojima, Kaname; Nariai, Naoki; Yamaguchi-Kabata, Yumi; Kawai, Yosuke; Takahashi, Mamoru; Mimori, Takahiro; Nagasaki, Masao

2014-08-08

Next-generation sequencers (NGSs) have become one of the main tools for current biology. To obtain useful insights from the NGS data, it is essential to control low-quality portions of the data affected by technical errors such as air bubbles in sequencing fluidics. We develop a software SUGAR (subtile-based GUI-assisted refiner) which can handle ultra-high-throughput data with user-friendly graphical user interface (GUI) and interactive analysis capability. The SUGAR generates high-resolution quality heatmaps of the flowcell, enabling users to find possible signals of technical errors during the sequencing. The sequencing data generated from the error-affected regions of a flowcell can be selectively removed by automated analysis or GUI-assisted operations implemented in the SUGAR. The automated data-cleaning function based on sequence read quality (Phred) scores was applied to a public whole human genome sequencing data and we proved the overall mapping quality was improved. The detailed data evaluation and cleaning enabled by SUGAR would reduce technical problems in sequence read mapping, improving subsequent variant analysis that require high-quality sequence data and mapping results. Therefore, the software will be especially useful to control the quality of variant calls to the low population cells, e.g., cancers, in a sample with technical errors of sequencing procedures.

Training Manual for Elements of Interface Definition and Control

NASA Technical Reports Server (NTRS)

Lalli, Vincent R. (Editor); Kastner, Robert E. (Editor); Hartt, Henry N. (Editor)

1997-01-01

The primary thrust of this manual is to ensure that the format and information needed to control interfaces between equipment are clear and understandable. The emphasis is on controlling the engineering design of the interface and not on the functional performance requirements of the system or the internal workings of the interfacing equipment. Interface control should take place, with rare exception, at the interfacing elements and no further. There are two essential sections of the manual. Chapter 2, Principles of Interface Control, discusses how interfaces are defined. It describes different types of interfaces to be considered and recommends a format for the documentation necessary for adequate interface control. Chapter 3, The Process: Through the Design Phases, provides tailored guidance for interface definition and control. This manual can be used to improve planned or existing interface control processes during system design and development. It can also be used to refresh and update the corporate knowledge base. The information presented herein will reduce the amount of paper and data required in interface definition and control processes by as much as 50 percent and will shorten the time required to prepare an interface control document. It also highlights the essential technical parameters that ensure that flight subsystems will indeed fit together and function as intended after assembly and checkout.

Home telemonitoring of vital signs--technical challenges and future directions.

PubMed

Celler, Branko G; Sparks, Ross S

2015-01-01

The telemonitoring of vital signs from the home is an essential element of telehealth services for the management of patients with chronic conditions, such as congestive heart failure (CHF), chronic obstructive pulmonary disease (COPD), diabetes, or poorly controlled hypertension. Telehealth is now being deployed widely in both rural and urban settings, and in this paper, we discuss the contribution made by biomedical instrumentation, user interfaces, and automated risk stratification algorithms in developing a clinical diagnostic quality longitudinal health record at home. We identify technical challenges in the acquisition of high-quality biometric signals from unsupervised patients at home, identify new technical solutions and user interfaces, and propose new measurement modalities and signal processing techniques for increasing the quality and value of vital signs monitoring at home. We also discuss use of vital signs data for the automated risk stratification of patients, so that clinical resources can be targeted to those most at risk of unscheduled admission to hospital. New research is also proposed to integrate primary care, hospital, personal genomic, and telehealth electronic health records, and apply predictive analytics and data mining for enhancing clinical decision support.

Technologies for diagnosis and treatment of acute stroke

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fitch, J.P.

1998-02-09

From October 1994 to June 1997, a multidisciplinary team of scientists and engineers at Lawrence Livermore National Laboratory were funded through LDRD to develop and integrate technologies for diagnosis and treatment of acute stroke. The project was summarized in a Science and Technology Review article `Brain Attack` that appeared in June 1997 and again in the Center for Healthcare Technologies Report (UCRL-LR-124761). This article is the best overview of the project, epidemiology of stroke and technical progress. Most of the technical progress has been documented in conference papers and presentations and refereed journal articles. Additional technical publication can be expectedmore » as our remaining patent applications progress through the US Patent and Trademark Office. The purpose of this report is to provide an appropriate introduction and organization to the numerous publications so that interested readers can quickly find information. Because there is no documentation for the history of this project, this report provides a summary. It also provides the final status report for the LDRD funding.« less

Orbiter middeck/payload standard interfaces control document

NASA Technical Reports Server (NTRS)

1984-01-01

The interfaces which shall be provided by the baseline shuttle mid-deck for payload use within the mid-deck area are defined, as well as all constraints which shall be observed by all the users of the defined interfaces. Commonality was established with respect to analytical approaches, analytical models, technical data and definitions for integrated analyses by all the interfacing parties. Any payload interfaces that are out of scope with the standard interfaces defined shall be defined in a Payload Unique Interface Control Document (ICD) for a given payload. Each Payload Unique ICD will have comparable paragraphs to this ICD and will have a corresponding notation of A, for applicable; N/A, for not applicable; N, for note added for explanation; and E, for exception. On any flight, the STS reserves the right to assign locations to both payloads mounted on an adapter plate(s) and payloads stored within standard lockers. Specific locations requests and/or requirements exceeding standard mid-deck payload requirements may result in a reduction in manifesting opportunities.

Proceedings: Computer Science and Data Systems Technical Symposium, volume 2

NASA Technical Reports Server (NTRS)

Larsen, Ronald L.; Wallgren, Kenneth

1985-01-01

Progress reports and technical updates of programs being performed by NASA centers are covered. Presentations in viewgraph form, along with abstracts, are included for topics in three catagories: computer science, data systems, and space station applications.

A study on operation efficiency evaluation based on firm's financial index and benchmark selection: take China Unicom as an example

NASA Astrophysics Data System (ADS)

Wu, Zu-guang; Tian, Zhan-jun; Liu, Hui; Huang, Rui; Zhu, Guo-hua

2009-07-01

Being the only listed telecom operators of A share market, China Unicom has always been attracted many institutional investors under the concept of 3G recent years,which itself is a great technical progress expectation.Do the institutional investors or the concept of technical progress have signficant effect on the improving of firm's operating efficiency?Though reviewing the documentary about operating efficiency we find that schoolars study this problem useing the regress analyzing based on traditional production function and data envelopment analysis(DEA) and financial index anayzing and marginal function and capital labor ratio coefficient etc. All the methods mainly based on macrodata. This paper we use the micro-data of company to evaluate the operating efficiency.Using factor analyzing based on financial index and comparing the factor score of three years from 2005 to 2007, we find that China Unicom's operating efficiency is under the averge level of benchmark corporates and has't improved under the concept of 3G from 2005 to 2007.In other words,institutional investor or the conception of technical progress expectation have faint effect on the changes of China Unicom's operating efficiency. Selecting benchmark corporates as post to evaluate the operating efficiency is a characteristic of this method ,which is basicallly sipmly and direct.This method is suit for the operation efficiency evaluation of agriculture listed companies because agriculture listed also face technical progress and marketing concept such as tax-free etc.

Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-05-01

West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Reports on a quarterly basis. This report comprises the first Quarterly Technical Progress Report for Year 2 of the Agreement. This report reflects the progress and/or efforts performed on the sixteen (16) technical projects encompassed by the Year 2 Agreement for the period of January 1 through March 31, 1994. In situ bioremediation ofmore » chlorinated organic solvents; Microbial enrichment for enhancing in-situ biodegradation of hazardous organic wastes; Treatment of volatile organic compounds (VOCs) using biofilters; Drain-enhanced soil flushing (DESF) for organic contaminants removal; Chemical destruction of chlorinated organic compounds; Remediation of hazardous sites with steam reforming; Soil decontamination with a packed flotation column; Use of granular activated carbon columns for the simultaneous removal of organics, heavy metals, and radionuclides; Monolayer and multilayer self-assembled polyion films for gas-phase chemical sensors; Compact mercuric iodide detector technology development; Evaluation of IR and mass spectrometric techniques for on-site monitoring of volatile organic compounds; A systematic database of the state of hazardous waste clean-up technologies; Dust control methods for insitu nuclear and hazardous waste handling; Winfield Lock and Dam remediation; and Socio-economic assessment of alternative environmental restoration technologies.« less

Contextual Sensing: Integrating Contextual Information with Human and Technical Geo-Sensor Information for Smart Cities

PubMed Central

Sagl, Günther; Resch, Bernd; Blaschke, Thomas

2015-01-01

In this article we critically discuss the challenge of integrating contextual information, in particular spatiotemporal contextual information, with human and technical sensor information, which we approach from a geospatial perspective. We start by highlighting the significance of context in general and spatiotemporal context in particular and introduce a smart city model of interactions between humans, the environment, and technology, with context at the common interface. We then focus on both the intentional and the unintentional sensing capabilities of today’s technologies and discuss current technological trends that we consider have the ability to enrich human and technical geo-sensor information with contextual detail. The different types of sensors used to collect contextual information are analyzed and sorted into three groups on the basis of names considering frequently used related terms, and characteristic contextual parameters. These three groups, namely technical in situ sensors, technical remote sensors, and human sensors are analyzed and linked to three dimensions involved in sensing (data generation, geographic phenomena, and type of sensing). In contrast to other scientific publications, we found a large number of technologies and applications using in situ and mobile technical sensors within the context of smart cities, and surprisingly limited use of remote sensing approaches. In this article we further provide a critical discussion of possible impacts and influences of both technical and human sensing approaches on society, pointing out that a larger number of sensors, increased fusion of information, and the use of standardized data formats and interfaces will not necessarily result in any improvement in the quality of life of the citizens of a smart city. This article seeks to improve our understanding of technical and human geo-sensing capabilities, and to demonstrate that the use of such sensors can facilitate the integration of different types of contextual information, thus providing an additional, namely the geo-spatial perspective on the future development of smart cities. PMID:26184221

Contextual Sensing: Integrating Contextual Information with Human and Technical Geo-Sensor Information for Smart Cities.

PubMed

Sagl, Günther; Resch, Bernd; Blaschke, Thomas

2015-07-14

In this article we critically discuss the challenge of integrating contextual information, in particular spatiotemporal contextual information, with human and technical sensor information, which we approach from a geospatial perspective. We start by highlighting the significance of context in general and spatiotemporal context in particular and introduce a smart city model of interactions between humans, the environment, and technology, with context at the common interface. We then focus on both the intentional and the unintentional sensing capabilities of today's technologies and discuss current technological trends that we consider have the ability to enrich human and technical geo-sensor information with contextual detail. The different types of sensors used to collect contextual information are analyzed and sorted into three groups on the basis of names considering frequently used related terms, and characteristic contextual parameters. These three groups, namely technical in situ sensors, technical remote sensors, and human sensors are analyzed and linked to three dimensions involved in sensing (data generation, geographic phenomena, and type of sensing). In contrast to other scientific publications, we found a large number of technologies and applications using in situ and mobile technical sensors within the context of smart cities, and surprisingly limited use of remote sensing approaches. In this article we further provide a critical discussion of possible impacts and influences of both technical and human sensing approaches on society, pointing out that a larger number of sensors, increased fusion of information, and the use of standardized data formats and interfaces will not necessarily result in any improvement in the quality of life of the citizens of a smart city. This article seeks to improve our understanding of technical and human geo-sensing capabilities, and to demonstrate that the use of such sensors can facilitate the integration of different types of contextual information, thus providing an additional, namely the geo-spatial perspective on the future development of smart cities.

Seizing the Future: How Ohio's Career-Technical Education Programs Fuse Academic Rigor and Real-World Experiences to Prepare Students for College and Careers

ERIC Educational Resources Information Center

Guarino, Heidi; Yoder, Shaun

2015-01-01

"Seizing the Future: How Ohio's Career and Technical Education Programs Fuse Academic Rigor and Real-World Experiences to Prepare Students for College and Work," demonstrates Ohio's progress in developing strong policies for career and technical education (CTE) programs to promote rigor, including college- and career-ready graduation…

Case Study on Technical and Vocational Education in Japan. Case Studies on Technical and Vocational Education in Asia and the Pacific.

ERIC Educational Resources Information Center

Iwamoto, Muneharu

In the course of Japan's economic progress, remarkable changes have occurred in the structure of industry and employment. Workers are in extremely short supply in such occupations as mining, manufacturing and construction, services, transportation and communication, sales, and professional and technical. On the basis of recommendations of the…

Teleneurosonology: a novel application of transcranial and carotid ultrasound.

PubMed

Rubin, Mark N; Barrett, Kevin M; Freeman, W David; Lee Iannotti, Joyce K; Channer, Dwight D; Rabinstein, Alejandro A; Demaerschalk, Bart M

2015-03-01

To demonstrate the technical feasibility of interfacing transcranial Doppler (TCD) and carotid "duplex" ultrasonography (CUS) peripherals with telemedicine end points to provide real-time spectral waveform and duplex imaging data for remote review and interpretation. We performed remote TCD and CUS examinations on a healthy, volunteer employee from our institution without known cerebrovascular disease. The telemedicine end point was stationed in our institution's hospital where the neurosonology examinations took place and the control station was in a dedicated telemedicine room in a separate building. The examinations were performed by a postgraduate level neurohospitalist trainee (M.N.R.) and interpreted by an attending vascular neurologist, both with experience in the performance and interpretation of TCD and CUS. Spectral waveform and duplex ultrasound data were successfully transmitted from TCD and CUS instruments through a telemedicine end point to a remote reviewer at a control station. Image quality was preserved in all cases, and technical failures were not encountered. This proof-of-concept study demonstrates the technical feasibility of interfacing TCD and CUS peripherals with a telemedicine end point to provide real-time spectral waveform and duplex imaging data for remote review and interpretation. Medical diagnostic and telemedicine devices should be equipped with interfaces that allow simple transmission of high-quality audio and video information from the medical devices to the telemedicine technology. Further study is encouraged to determine the clinical impact of teleneurosonology. Copyright © 2015 National Stroke Association. Published by Elsevier Inc. All rights reserved.

25 CFR 30.104 - What is the Secretary's definition of AYP?

Code of Federal Regulations, 2011 CFR

2011-04-01

... PROGRESS Defining Adequate Yearly Progress § 30.104 What is the Secretary's definition of AYP? The... accepted by the Department of Education. The Secretary is committed to providing technical assistance to a...

25 CFR 30.104 - What is the Secretary's definition of AYP?

Code of Federal Regulations, 2010 CFR

2010-04-01

... PROGRESS Defining Adequate Yearly Progress § 30.104 What is the Secretary's definition of AYP? The... accepted by the Department of Education. The Secretary is committed to providing technical assistance to a...

Excitonic processes at organic heterojunctions

NASA Astrophysics Data System (ADS)

He, ShouJie; Lu, ZhengHong

2018-02-01

Understanding excitonic processes at organic heterojunctions is crucial for development of organic semiconductor devices. This article reviews recent research on excitonic physics that involve intermolecular charge transfer (CT) excitons, and progress on understanding relationships between various interface energy levels and key parameters governing various competing interface excitonic processes. These interface excitonic processes include radiative exciplex emission, nonradiative recombination, Auger electron emission, and CT exciton dissociation. This article also reviews various device applications involving interface CT excitons, such as organic light-emitting diodes (OLEDs), organic photovoltaic cells, organic rectifying diodes, and ultralow-voltage Auger OLEDs.

ASSIST internals reference manual

NASA Technical Reports Server (NTRS)

Johnson, Sally C.; Boerschlein, David P.

1994-01-01

The Abstract Semi-Markov Specification Interface to the SURE Tool (ASSIST) program was developed at NASA LaRC in order to analyze the reliability of virtually any fault-tolerant system. A user manual was developed to detail its use. Certain technical specifics are of no concern to the end user, yet are of importance to those who must maintain and/or verify the correctness of the tool. This document takes a detailed look into these technical issues.

Our Theme for 2016: Sustaining Momentum

DTIC Science & Technology

2016-03-01

of design architectures and interfaces to make both open sys- tems and modularity a reality. This is “owning the technical baseline,” and the devil... write this year, although we will be implementing the changes required in the Fiscal Year (FY) 2016 National Defense Au- thorization Act. We still...Defense for Acquisition, Technology, and Logistics on the momentum we have gained as we get ready for a new administration next year. Promote Technical

Lessons learned in control center technologies and non-technologies

NASA Technical Reports Server (NTRS)

Hansen, Elaine R.

1991-01-01

Information is given in viewgraph form on the Solar Mesosphere Explorer (SME) Control Center and the Oculometer and Automated Space Interface System (OASIS). Topics covered include SME mission operations functions; technical and non-technical features of the SME control center; general tasks and objects within the Space Station Freedom (SSF) ground system nodes; OASIS-Real Time for the control and monitoring of of space systems and subsystems; and OASIS planning, scheduling, and PC architecture.

Architecture and Concept of Operations for a Warfighter’s Internet. Volume 2: Appendices

DTIC Science & Technology

1998-01-28

National Technical Information Service , where it will be available to the general public, including foreign nationals. This technical report has been...SUPPORT INTEGRATED SERVICES IN A MOBILE CELLULAR SYSTEM ARCHITECTURE (FOR ARCHITECTURE OPT. 2) B-1 1. Introduction B-l 2. Warfighter’s...Internet Architecture and Concept of Operation B-2 3. Subnet Provider Interface (SNPI) B-5 4. Integrated Services Cell Multiplexing (ISCM) B-9 5. Mobile

Material platforms for spin-based photonic quantum technologies

NASA Astrophysics Data System (ADS)

Atatüre, Mete; Englund, Dirk; Vamivakas, Nick; Lee, Sang-Yun; Wrachtrup, Joerg

2018-05-01

A central goal in quantum optics and quantum information science is the development of quantum networks to generate entanglement between distributed quantum memories. Experimental progress relies on the quality and efficiency of the light-matter quantum interface connecting the quantum states of photons to internal states of quantum emitters. Quantum emitters in solids, which have properties resembling those of atoms and ions, offer an opportunity for realizing light-matter quantum interfaces in scalable and compact hardware. These quantum emitters require a material platform that enables stable spin and optical properties, as well as a robust manufacturing of quantum photonic circuits. Because no emitter system is yet perfect and different applications may require different properties, several light-matter quantum interfaces are being developed in various platforms. This Review highlights the progress in three leading material platforms: diamond, silicon carbide and atomically thin semiconductors.

Defense Acquisitions: DOD Efforts to Adopt Open Systems for Its Unmanned Aircraft Systems Have Progressed Slowly

DTIC Science & Technology

2013-07-01

applications introduced by third-party developers to connect to the Android operating system through an open software interface. This allows customers...Definition Multimedia Interface have been developed to address the need for standards for high-definition televisions and computer monitors. Perhaps

CONTACT: An Air Force technical report on military satellite control technology

NASA Astrophysics Data System (ADS)

Weakley, Christopher K.

1993-07-01

This technical report focuses on Military Satellite Control Technologies and their application to the Air Force Satellite Control Network (AFSCN). This report is a compilation of articles that provide an overview of the AFSCN and the Advanced Technology Program, and discusses relevant technical issues and developments applicable to the AFSCN. Among the topics covered are articles on Future Technology Projections; Future AFSCN Topologies; Modeling of the AFSCN; Wide Area Communications Technology Evolution; Automating AFSCN Resource Scheduling; Health & Status Monitoring at Remote Tracking Stations; Software Metrics and Tools for Measuring AFSCN Software Performance; Human-Computer Interface Working Group; Trusted Systems Workshop; and the University Technical Interaction Program. In addition, Key Technology Area points of contact are listed in the report.

ANNUAL REPORT, JULY 1, 1958

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1959-02-01

This annual report of Brookhaven National Laboratory describes its program and activities for the fiscal year 1958. The progress and trends of the research program are presented along with a description of the operational, service, and administrative activities of the Laboratory. The scientific and technical details of the many research and development activities are covered more fully in scientific and technical periodicals and in the quarterly scientific progress reports and other scientiflc reports of the Laboratory. A list of all publications for July 1, 1957 to June 30, 1958, is given. Status and progress are given in fields of physics,more » accelerator development, instrumentation, applied mathematics, chemistry, nuclear engineering, biology, and medical research. (For preceding period see BNL-462.) (W.D.M.)« less

Towards a space-borne quantum gravity gradiometer: progress in laboratory demonstration

NASA Technical Reports Server (NTRS)

Yu, Nan; Kohel, James M.; Kellogg, James R.; Maleki, Lute

2005-01-01

This paper describes the working principles and technical benefits of atom-wave interferometer-based inertial sensors, and gives a progress report on the development of a quantum gravity gradiometer for space applications at JPL.

Technical Progress of the New Worlds Observer Mission

NASA Astrophysics Data System (ADS)

Lo, Amy; Noecker, C.; Cash, W.; NWO Study Team

2009-01-01

We report on the technical progress of the New Worlds Observer (NWO) mission concept. NWO is a two spacecraft mission that is capable of detecting and characterizing extra-solar, terrestrial planets and planetary systems. NWO consists of an external starshade and an UV-optical space telescope, flying in tandem. The starshade is a petal-shaped, opaque screen that creates an extremely dark shadow large enough to shade the telescope aperture from the target star. The NWO team has been addressing the top technology challenges of the concept, and report here our progress. We will present the current mission configuration best suited to address Terrestrial Planet Finding requirements, and highlight the technological breakthroughs that we have achieved this year. In particular, we will report on progress made in precision deployables for the large starshade, and the trajectory & alignment control system for NWO. We will also briefly highlight advances in understanding the starshade optical performance.

Universal interface of TAUOLA: Technical and physics documentation

NASA Astrophysics Data System (ADS)

Davidson, N.; Nanava, G.; Przedziński, T.; Richter-Waş, E.; Waş, Z.

2012-03-01

Because of their narrow width, τ decays can be well separated from their production process. Only spin degrees of freedom connect these two parts of the physics process of interest for high energy collision experiments. In the following, we present a Monte Carlo algorithm which is based on that property. The interface supplements events generated by other programs, with τ decays. Effects of spin, including transverse degrees of freedom, genuine weak corrections or of new physics may be taken into account at the time when a τ decay is generated and written into an event record. The physics content of the C++ interface is already now richer than its FORTRAN predecessor.

Current status of EVA degradation in Si modules and interface stability in CdTe/CdS modules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Czanderna, A.W.

1994-06-30

The goals, objectives, background, technical approach, status, and accomplishments on the PV Module Reliability Research Task are summarized for FY 1993. The accomplishments are reported in two elements, ethylene vinyl acetate (EVA) degradation and stability in CdTe/CdS modules. The EVA results are presented under the headings modified EVA and potential EVA replacements, degradation mechanisms, efficiency losses from yellowed EVA, and equipment acquisitions. The results on CdTe/CdS modules are presented under subheadings of stability of the SnO[sub 2]/CdS interface and degradation at the CdTe/CdS interface.

Mathematical model for the Bridgman-Stockbarger crystal growing system

NASA Technical Reports Server (NTRS)

Roberts, G. O.

1986-01-01

In a major technical breakthrough, a computer model for Bridgman-Stockbarger crystal growth was developed. The model includes melt convection, solute effects, thermal conduction in the ampule, melt, and crystal, and the determination of the curved moving crystal-melt interface. The key to the numerical method is the use of a nonuniform computational mesh which moves with the interface, so that the interface is a mesh surface. In addition, implicit methods are used for advection and diffusion of heat, concentration, and vorticity, for interface movement, and for internal gracity waves. This allows large time-steps without loss of stability or accuracy. Numerical results are presented for the interface shape, temperature distribution, and concentration distribution, in steady-state crystl growth. Solutions are presented for two test cases using water, with two different salts in solution. The two diffusivities differ by a factor of ten, and the concentrations differ by a factor of twenty.

A haptic interface for virtual simulation of endoscopic surgery.

PubMed

Rosenberg, L B; Stredney, D

1996-01-01

Virtual reality can be described as a convincingly realistic and naturally interactive simulation in which the user is given a first person illusion of being immersed within a computer generated environment While virtual reality systems offer great potential to reduce the cost and increase the quality of medical training, many technical challenges must be overcome before such simulation platforms offer effective alternatives to more traditional training means. A primary challenge in developing effective virtual reality systems is designing the human interface hardware which allows rich sensory information to be presented to users in natural ways. When simulating a given manual procedure, task specific human interface requirements dictate task specific human interface hardware. The following paper explores the design of human interface hardware that satisfies the task specific requirements of virtual reality simulation of Endoscopic surgical procedures. Design parameters were derived through direct cadaver studies and interviews with surgeons. Final hardware design is presented.

Picosecond laser bonding of highly dissimilar materials

NASA Astrophysics Data System (ADS)

Carter, Richard M.; Troughton, Michael; Chen, Jianyong; Elder, Ian; Thomson, Robert R.; Lamb, Robert A.; Esser, M. J. Daniel; Hand, Duncan P.

2016-10-01

We report on recent progress in developing an industrially relevant, robust technique to bond dissimilar materials through ultra-fast microwelding. This technique is based on the use of a 5.9ps, 400kHz Trumpf laser operating at 1030nm. Tight focusing of the laser radiation at, or around, the interface between two materials allows for simultaneous absorption in both. This absorption rapidly, and locally, heats the material forming plasma from both materials. With suitable surface preparation this plasma can be confined to the interface region where it mixes, cools and forms a weld between the two materials. The use of ps pulses results in a short interaction time. This enables a bond to form whilst limiting the heat affected zone (HAZ) to a region of only a few hundred micrometres across. This small scale allows for the bonding of materials with highly dissimilar thermal properties, and in particular coefficients of thermal expansion e.g. glass-metal bonding. We report on our results for a range of material combinations including, Al-Bk7, Al-SiO2 and Nd:YAG-AlSi. Emphasis will be laid on the technical requirements for bonding including the required surface preparation of the two materials and on the laser parameters required. The quality of the resultant bonds are characterized through shear force measurements (where strengths equal to and exceeding equivalent adhesives will be presented). The lifetime of the welds is also discussed, paying particular attention to the results of thermal cycling tests.

Center for Nanophase Materials Sciences

NASA Astrophysics Data System (ADS)

Horton, Linda

2002-10-01

The Center for Nanophase Materials Sciences (CNMS) will be a user facility with a strong component of joint, collaborative research. CNMS is being developed, together with the scientific community, with support from DOE's Office of Basic Energy Sciences. The Center will provide a thriving, multidisciplinary environment for research as well as the education of students and postdoctoral scholars. It will be co-located with the Spallation Neutron Source (SNS) and the Joint Institute for Neutron Sciences (JINS). The CNMS will integrate nanoscale research with neutron science, synthesis science, and theory/modeling/simulation, bringing together four areas in which the United States has clear national research and educational needs. The Center's research will be organized under three scientific thrusts: nano-dimensioned "soft" materials (including organic, hybrid, and interfacial nanophases); complex "hard" materials systems (including the crosscutting areas of interfaces and reduced dimensionality that become scientifically critical on the nanoscale); and theory/modeling/simulation. This presentation will summarize the progress towards identification of the specific research focus topics for the Center. Currently proposed topics, based on two workshops with the potential user community, include catalysis, nanomagnetism, synthetic and bio-inspired macromolecular materials, nanophase biomaterials, nanofluidics, optics/photonics, carbon-based nanostructures, collective behavior, nanoscale interface science, virtual synthesis and nanomaterials design, and electronic structure, correlations, and transport. In addition, the proposed 80,000 square foot facility (wet/dry labs, nanofabrication clean rooms, and offices) and the associated technical equipment will be described. The CNMS is scheduled to begin construction in spring, 2003. Initial operations are planned for late in 2004.

Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1, 1997--July 31, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

Progress summaries are provided from the Amarillo National Center for Plutonium. Programs include the plutonium information resource center, environment, public health, and safety, education and training, nuclear and other material studies.

United States Air Force Graduate Student Research Program for 1990. Program Technical Report. Volume 1

DTIC Science & Technology

1991-06-05

functions on the excavator. 28-6 m0 E Figure 1: Conceptual User Interface for the Rapid Runway Repair (RRR) Remote Control System IV. COMMUNICATION SYSTEM...Vehicle Systems Conference, Dayton, OH. Mariani, D., 1988, "Robotic Vehicle Communications Interoperability," RD& E Center Technical Report, US Army Tank...D.g e : BS Va;,derbilt University Specialty: Computer Engineering Electrical Eng. Dept. Absigned: Arnold Er-gineering Nashville, TN 37240 Developmer

Technical Issues in Evolving to Integrated Services Digital Network (ISDN)

DTIC Science & Technology

1991-06-01

channel through some Page 13 Technical Issues in Evolving to ISDN Final Report separate interface (such as the AT command set of the Hayes modems or the...errors experienced over standard modem provided connectivity. But, in this project connectivity has been established only over a single CO. Those...examined to some extent and are discussed below. Existing equipment was of two types: that which treats ISDN as just another leased line providing 56k or

Standard Engineering Installation Package, Technical Control Facility, Technical Control Improvement Program (TCIP)

DTIC Science & Technology

1979-10-01

software. This document may not be cited for purpose of advertisement . AVAILABILITY This publication is available to non-Government agencies and may be...voltage interface requirements for repeaters. This supply occupies one slot in the 10306 mounting shelf. 1.4.2.8.5 Teletypewriter monitor. The AN/ UGC -61X...The AN/ UGC -61X keyboard send-receive (KSR) TTY set is an electromechanical apparatus that provides terminal facilities with two receive only, one KSR

Urology technical and non-technical skills development: the emerging role of simulation.

PubMed

Rashid, Prem; Gianduzzo, Troy R J

2016-04-01

To review the emerging role of technical and non-technical simulation in urological education and training. A review was conducted to examine the current role of simulation in urology training. A PUBMED search of the terms 'urology training', 'urology simulation' and 'urology education' revealed 11,504 titles. Three hundred and fifty-seven abstracts were identified as English language, peer reviewed papers pertaining to the role of simulation in urology and related topics. Key papers were used to explore themes. Some cross-referenced papers were also included. There is an ongoing need to ensure that training time is efficiently utilised while ensuring that optimal technical and non-technical skills are achieved. Changing working conditions and the need to minimise patient harm by inadvertent errors must be taken into account. Simulation models for specific technical aspects have been the mainstay of graduated step-wise low and high fidelity training. Whole scenario environments as well as non-technical aspects can be slowly incorporated into the curriculum. Doing so should also help define what have been challenging competencies to teach and evaluate. Dedicated time, resources and trainer up-skilling are important. Concurrent studies are needed to help evaluate the effectiveness of introducing step-wise simulation for technical and non-technical competencies. Simulation based learning remains the best avenue of progressing surgical education. Technical and non-technical simulation could be used in the selection process. There are good economic, logistic and safety reasons to pursue the process of ongoing development of simulation co-curricula. While the role of simulation is assured, its progress will depend on a structured program that takes advantage of what can be delivered via this medium. Overall, simulation can be developed further for urological training programs to encompass technical and non-technical skill development at all stages, including recertification. © 2015 The Authors BJU International © 2015 BJU International Published by John Wiley & Sons Ltd.

A Portfolio Analysis Tool for Measuring NASAs Aeronautics Research Progress toward Planned Strategic Outcomes

NASA Technical Reports Server (NTRS)

Tahmasebi, Farhad; Pearce, Robert

2016-01-01

Description of a tool for portfolio analysis of NASA's Aeronautics research progress toward planned community strategic Outcomes is presented. The strategic planning process for determining the community Outcomes is also briefly described. Stakeholder buy-in, partnership performance, progress of supporting Technical Challenges, and enablement forecast are used as the criteria for evaluating progress toward Outcomes. A few illustrative examples are also presented.

An approach to knowledge structuring for advanced phases of the Technical and Management Information System (TMIS)

NASA Technical Reports Server (NTRS)

Goranson, H. T.

1986-01-01

The Technical and Management Information System (TMIS) must employ on enlightened approach to its object structure, but basic issues in conceptual structuring remain to be resolved. Sirius outlines the necessary agenda and reports on progress toward solutions.

48 CFR 752.7035 - Public notices.

Code of Federal Regulations, 2011 CFR

2011-10-01

... notices. The following clause is for use when the cognizant technical office determines that the contract... to time, to announce progress and accomplishments. Press releases or other public notices should... cognizant technical officer and to USAID's Legislative and Public Affairs (LPA) as far in advance of release...

14 CFR 1260.71 - Supplements and renewals.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., continued research relevance, and progress made by the recipient. (2) To insure uninterrupted programs, the technical office should forward to the grant office a completed award package, including a funded procurement request, technical evaluation of the proposed budget, and other support documentation, at least 29...

[A technical modification of the use of Dwyer's equipment].

PubMed

Carlioz, H; Damsin, J P

1991-01-01

Dwyer's technique for correction and anterior fusion of the spine was improved by using lockers at the level of each screw. So, like with the Zielke's technic this procedure allowed a global progressive and controllable correction and a real derotation of the spine.

Final Technical Report - SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schnack, Dalton D.

Final technical report for research performed by Dr. Thomas G. Jenkins in collaboration with Professor Dalton D. Schnack on SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodyanics, DE-FC02-06ER54899, for the period of 8/15/06 - 8/14/11. This report centers on the Slow MHD physics campaign work performed by Dr. Jenkins while at UW-Madison and then at Tech-X Corporation. To make progress on the problem of RF induced currents affect magnetic island evolution in toroidal plasmas, a set of research approaches are outlined. Three approaches can be addressed in parallel. These are: (1) Analytically prescribed additional term in Ohm's law tomore » model the effect of localized ECCD current drive; (2) Introduce an additional evolution equation for the Ohm's law source term. Establish a RF source 'box' where information from the RF code couples to the fluid evolution; and (3) Carry out a more rigorous analytic calculation treating the additional RF terms in a closure problem. These approaches rely on the necessity of reinvigorating the computation modeling efforts of resistive and neoclassical tearing modes with present day versions of the numerical tools. For the RF community, the relevant action item is - RF ray tracing codes need to be modified so that general three-dimensional spatial information can be obtained. Further, interface efforts between the two codes require work as well as an assessment as to the numerical stability properties of the procedures to be used.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hardin, Dave; Stephan, Eric G.; Wang, Weimin

Through its Building Technologies Office (BTO), the United States Department of Energy’s Office of Energy Efficiency and Renewable Energy (DOE-EERE) is sponsoring an effort to advance interoperability for the integration of intelligent buildings equipment and automation systems, understanding the importance of integration frameworks and product ecosystems to this cause. This is important to BTO’s mission to enhance energy efficiency and save energy for economic and environmental purposes. For connected buildings ecosystems of products and services from various manufacturers to flourish, the ICT aspects of the equipment need to integrate and operate simply and reliably. Within the concepts of interoperability liemore » the specification, development, and certification of equipment with standards-based interfaces that connect and work. Beyond this, a healthy community of stakeholders that contribute to and use interoperability work products must be developed. On May 1, 2014, the DOE convened a technical meeting to take stock of the current state of interoperability of connected equipment and systems in buildings. Several insights from that meeting helped facilitate a draft description of the landscape of interoperability for connected buildings, which focuses mainly on small and medium commercial buildings. This document revises the February 2015 landscape document to address reviewer comments, incorporate important insights from the Buildings Interoperability Vision technical meeting, and capture thoughts from that meeting about the topics to be addressed in a buildings interoperability vision. In particular, greater attention is paid to the state of information modeling in buildings and the great potential for near-term benefits in this area from progress and community alignment.« less

NAS infrastructure management system build 1.5 computer-human interface

DOT National Transportation Integrated Search

2001-01-01

Human factors engineers from the National Airspace System (NAS) Human Factors Branch (ACT-530) of the Federal Aviation Administration William J. Hughes Technical Center conducted an evaluation of the NAS Infrastructure Management System (NIMS) Build ...

23. SITE BUILDING 002 SCANNER BUILDING RADAR CONTROL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. SITE BUILDING 002 - SCANNER BUILDING - RADAR CONTROL INTERFACE "RCL NO. 2" WITH COMPUTER CONTROL DISC DRIVE UNITS IN FOREGROUND. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

Technical Requirements Analysis and Control Systems (TRACS) Initial Operating Capability (IOC) documentation

NASA Technical Reports Server (NTRS)

Hammond, Dana P.

1991-01-01

The Technical Requirements Analysis and Control Systems (TRACS) software package is described. TRACS offers supplemental tools for the analysis, control, and interchange of project requirements. This package provides the fundamental capability to analyze and control requirements, serves a focal point for project requirements, and integrates a system that supports efficient and consistent operations. TRACS uses relational data base technology (ORACLE) in a stand alone or in a distributed environment that can be used to coordinate the activities required to support a project through its entire life cycle. TRACS uses a set of keyword and mouse driven screens (HyperCard) which imposes adherence through a controlled user interface. The user interface provides an interactive capability to interrogate the data base and to display or print project requirement information. TRACS has a limited report capability, but can be extended with PostScript conventions.

A systematic assessment of the state of hazardous waste clean-up technologies. Quarterly technical progress report, April 1--June 30, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berg, M.T.; Reed, B.E.; Gabr, M.

1993-07-01

West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Report for Year 1 of the Agreement. This report reflects the progress and/or efforts performed on the following nine technical projects encompassed by the Year 1 Agreement for the period of April 1 through June 30, 1993: Systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies -- drain-enhanced soil flushingmore » (DESF) for organic contaminants removal; site remediation technologies -- in situ bioremediation of organic contaminants; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors -- monolayer and multilayer self-assembled films for chemical sensors; Winfield lock and dam remediation; Assessments of Technologies for hazardous waste site remediation -- non-treatment technologies and pilot scale test facility implementation; and remediation of hazardous sites with stream reforming.« less

Density gradients at hydrogel interfaces for enhanced cell penetration.

PubMed

Simona, B R; Hirt, L; Demkó, L; Zambelli, T; Vörös, J; Ehrbar, M; Milleret, V

2015-04-01

We report that stiffness gradients facilitate infiltration of cells through otherwise cell-impermeable hydrogel interfaces. By enabling the separation of hydrogel manufacturing and cell seeding, and by improving cell colonization of additively manufactured hydrogel elements, interfacial density gradients present a promising strategy to progress in the creation of 3D tissue models.

Progress towards biocompatible intracortical microelectrodes for neural interfacing applications

NASA Astrophysics Data System (ADS)

Jorfi, Mehdi; Skousen, John L.; Weder, Christoph; Capadona, Jeffrey R.

2015-02-01

To ensure long-term consistent neural recordings, next-generation intracortical microelectrodes are being developed with an increased emphasis on reducing the neuro-inflammatory response. The increased emphasis stems from the improved understanding of the multifaceted role that inflammation may play in disrupting both biologic and abiologic components of the overall neural interface circuit. To combat neuro-inflammation and improve recording quality, the field is actively progressing from traditional inorganic materials towards approaches that either minimizes the microelectrode footprint or that incorporate compliant materials, bioactive molecules, conducting polymers or nanomaterials. However, the immune-privileged cortical tissue introduces an added complexity compared to other biomedical applications that remains to be fully understood. This review provides a comprehensive reflection on the current understanding of the key failure modes that may impact intracortical microelectrode performance. In addition, a detailed overview of the current status of various materials-based approaches that have gained interest for neural interfacing applications is presented, and key challenges that remain to be overcome are discussed. Finally, we present our vision on the future directions of materials-based treatments to improve intracortical microelectrodes for neural interfacing.

Progress Towards Biocompatible Intracortical Microelectrodes for Neural Interfacing Applications

PubMed Central

Jorfi, Mehdi; Skousen, John L.; Weder, Christoph; Capadona, Jeffrey R.

2015-01-01

To ensure long-term consistent neural recordings, next-generation intracortical microelectrodes are being developed with an increased emphasis on reducing the neuro-inflammatory response. The increased emphasis stems from the improved understanding of the multifaceted role that inflammation may play in disrupting both biologic and abiologic components of the overall neural interface circuit. To combat neuro-inflammation and improve recording quality, the field is actively progressing from traditional inorganic materials towards approaches that either minimizes the microelectrode footprint or that incorporate compliant materials, bioactive molecules, conducting polymers or nanomaterials. However, the immune-privileged cortical tissue introduces an added complexity compared to other biomedical applications that remains to be fully understood. This review provides a comprehensive reflection on the current understanding of the key failure modes that may impact intracortical microelectrode performance. In addition, a detailed overview of the current status of various materials-based approaches that have gained interest for neural interfacing applications is presented, and key challenges that remain to be overcome are discussed. Finally, we present our vision on the future directions of materials-based treatments to improve intracortical microelectrodes for neural interfacing. PMID:25460808

[Research progress and trend on grassland agroecology].

PubMed

Ren, Jizhou; Li, Xianglin; Hou, Fujiang

2002-08-01

The connotation, progress, research frontiers and developmental trend of grassland agroecology are discussed in this paper. The interface theory, structure and function, coupling and discordance, and health assessment of grassland agroecosystems were recognized as the four research frontiers of the discipline. There exist three primary interfaces in a grassland agroecosystem, i.e., vegetation-site, grassland-animal and production-management. Research into a series of the ecological processes that occurred at these interfaces is the key to revealing the features of the system behavior. There are four sections in a grassland agroecosystem, i.e., pre-plant, plant, animal and post-biotic sections. System coupling and discordance are the two important concepts to describe interactions among the production sections. System coupling among the sections can lead to system improvement by exerting the potential of system capacity. Health of an ecosystem is a reflection of its structure and function, and health assessment is a measurement of its orderliness and service value.

Prospective assessment of CAD/CAM zirconia abutment and lithium disilicate crown restorations: 2.4 year results.

PubMed

Cooper, Lyndon F; Stanford, Clark; Feine, Jocelyne; McGuire, Michael

2016-07-01

Single-tooth implant restorations are commonly used to replace anterior maxillary teeth. The esthetic, functional, and biologic outcomes are, in part, a function of the abutment and crown. The purpose of this clinical study was to describe the implant, abutment, and crown survival and complication rates for CAD/CAM zirconia abutment and lithium disilicate crown restorations for single-tooth implants. As part of a broader prospective investigation that enrolled and treated 141 participants comparing tissue responses at the conical interface (CI; AstraTech OsseoSpeed), flat-to-flat interface (FI; NobelSpeedy), and platform-switch interface (PS; NanoTite Certain Prevail) of single-tooth implants, computer-aided design and computer-aided manufacturing (CAD/CAM) zirconia abutments (ATLANTIS Abutment) and cemented lithium disilicate (e.max) crowns were used in the restoration of all implants. After 2.4 years in function (3 years after implant placement), the implant, abutment, and crown of 110 participants were evaluated. Technical and biologic complications were recorded. Demographic results were tabulated as percentages with mean values and standard deviations. Abutment survival was calculated with the Kaplan-Meier method. After 2.4 years, no abutments or crowns had been lost. Abutment complications (screw loosening, screw fracture, fracture) were absent for all 3 implant groups. Crown complications were limited to 2 crowns debonding and 1 with excess cement (2.5%). Five biological complications (4.0%) were recorded. The overall complication rate was 6.5%. CAD/CAM zirconia abutments restored with cemented lithium disilicate crowns demonstrated high survival on 3 different implant-abutment interface designs. No abutment or abutment screw fracture occurred. The technical complications observed after 2.4 years were minor and reversible. The use of CAD/CAM zirconia abutments with cemented lithium disilicate crowns is associated with high technical and biologic success at 2.4 years. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Progress, innovation and regulatory science in drug development: the politics of international standard-setting.

PubMed

Abraham, John; Reed, Tim

2002-06-01

This paper examines international standard-setting in the toxicology of pharmaceuticals during the 1990s, which has involved both the pharmaceutical industry and regulatory agencies in an organization known as the International Conference on Harmonisation of Technical Requirements for Registration of Pharmaceuticals for Human Use (ICH). The analysis shows that the relationships between innovation, regulatory science and 'progress' may be more complex and controversial than is often assumed. An assessment of the ICH's claims about the implications of 'technical' harmonization of drug-testing standards for the maintenance of drug safety, via toxicological testing, and the delivery of therapeutic progress, via innovation, is presented. By demonstrating that there is not a technoscientific validity for these claims, it is argued that, within the ICH, a discourse of technological innovation and scientific progress has been used by regulatory agencies and prominent parts of the transnational pharmaceutical industry to legitimize the lowering and loosening of toxicological standards for drug testing. The mobilization and acceptance of this discourse are shown to be pivotal to the ICH's transformation of reductions in safety standards, which are apparently against the interests of patients and public health, into supposed therapeutic benefits derived from promises of greater access to more innovative drug products. The evidence suggests that it is highly implausible that these reductions in the standards of regulatory toxicology are consistent with therapeutic progress for patients, and highlights a worrying aspect embedded in the 'technical trajectories' of regulatory science.

7 CFR 1944.541 - Reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) PROGRAM REGULATIONS (CONTINUED) HOUSING Technical and Supervisory Assistance Grants § 1944.541 Reporting... District Director to determine satisfactory progress. The District Director will work with the grantee to... five working days of receipt. (1) If the reports indicate satisfactory progress, the State Director...

Automatic control of a primary electric thrust subsystem

NASA Technical Reports Server (NTRS)

Macie, T. W.; Macmedan, M. L.

1975-01-01

A concept for automatic control of the thrust subsystem has been developed by JPL and participating NASA Centers. This paper reports on progress in implementing the concept at JPL. Control of the Thrust Subsystem (TSS) is performed by the spacecraft computer command subsystem, and telemetry data is extracted by the spacecraft flight data subsystem. The Data and Control Interface Unit, an element of the TSS, provides the interface with the individual elements of the TSS. The control philosophy and implementation guidelines are presented. Control requirements are listed, and the control mechanism, including the serial digital data intercommunication system, is outlined. The paper summarizes progress to Fall 1974.

An Irreversible Constitutive Law for Modeling the Delamination Process using Interface Elements

NASA Technical Reports Server (NTRS)

Goyal, Vinay K.; Johnson, Eric R.; Davila, Carlos G.; Jaunky, Navin; Ambur, Damodar (Technical Monitor)

2002-01-01

An irreversible constitutive law is postulated for the formulation of interface elements to predict initiation and progression of delamination in composite structures. An exponential function is used for the constitutive law such that it satisfies a multi-axial stress criterion for the onset of delamination, and satisfies a mixed mode fracture criterion for the progression of delamination. A damage parameter is included to prevent the restoration of the previous cohesive state between the interfacial surfaces. To demonstrate the irreversibility capability of the constitutive law, steady-state crack growth is simulated for quasi-static loading-unloading cycle of various fracture test specimens.

An Irreversible Constitutive Law for Modeling the Delamination Process Using Interface Elements

NASA Technical Reports Server (NTRS)

Goyal, Vinay K.; Johnson, Eric R.; Davila, Carlos G.; Jaunky, Navin; Bushnell, Dennis M. (Technical Monitor)

2002-01-01

An irreversible constitutive law is postulated for the formulation of interface elements to predict initiation and progression of delamination in composite structures. An exponential function is used for the constitutive law such that it satisfies a multi-axial stress criterion for the onset of delamination, and satisfies a mixed mode fracture criterion for the progression of delamination. A damage parameter is included to prevent the restoration of the previous cohesive state between the interfacial surfaces. To demonstrate the irreversibility capability of the constitutive law, steady-state crack growth is simulated for quasi-static loading-unloading cycle of various fracture test specimens.

Development of mining guidance and control systems

NASA Technical Reports Server (NTRS)

1979-01-01

New fundamental interface sensor concepts were identified and investigated including tabulation of the physical and performance characteristics of two new interface detector concepts: - natural background radiation and magnetic spin resonance. Studies of guidance and control techniques for the longwall miner identified three basic systems for use in automated/remote controlled longwall mining. The following projects were initiated: system study which will more completely define the longwall guidance and control system design concepts; integration of the various control functions (vertical, yaw, and roll); and hardware technical requirements.

Fourth Annual Workshop on Space Operations Applications and Research (SOAR 90)

NASA Technical Reports Server (NTRS)

Savely, Robert T. (Editor)

1991-01-01

The papers from the symposium are presented. Emphasis is placed on human factors engineering and space environment interactions. The technical areas covered in the human factors section include: satellite monitoring and control, man-computer interfaces, expert systems, AI/robotics interfaces, crew system dynamics, and display devices. The space environment interactions section presents the following topics: space plasma interaction, spacecraft contamination, space debris, and atomic oxygen interaction with materials. Some of the above topics are discussed in relation to the space station and space shuttle.

Lyceum: A Multi-Protocol Digital Library Gateway

NASA Technical Reports Server (NTRS)

Maa, Ming-Hokng; Nelson, Michael L.; Esler, Sandra L.

1997-01-01

Lyceum is a prototype scalable query gateway that provides a logically central interface to multi-protocol and physically distributed, digital libraries of scientific and technical information. Lyceum processes queries to multiple syntactically distinct search engines used by various distributed information servers from a single logically central interface without modification of the remote search engines. A working prototype (http://www.larc.nasa.gov/lyceum/) demonstrates the capabilities, potentials, and advantages of this type of meta-search engine by providing access to over 50 servers covering over 20 disciplines.

Natural language interface for command and control

NASA Technical Reports Server (NTRS)

Shuler, Robert L., Jr.

1986-01-01

A working prototype of a flexible 'natural language' interface for command and control situations is presented. This prototype is analyzed from two standpoints. First is the role of natural language for command and control, its realistic requirements, and how well the role can be filled with current practical technology. Second, technical concepts for implementation are discussed and illustrated by their application in the prototype system. It is also shown how adaptive or 'learning' features can greatly ease the task of encoding language knowledge in the language processor.

The magnetohydrodynamics coal-fired flow facility

NASA Astrophysics Data System (ADS)

1995-01-01

In this quarterly technical progress report, UTSI reports on the status of a multitask contract to develop the technology for the steam bottoming portion of a MHD Steam Combined Cycle Power Plant. The report describes the facility maintenance and environmental work completed, status of completing technical reports and certain key administrative actions occurring during the quarter. With program resources at a minimum to closeout the MHD program, no further testing occurred during the quarter, but the DOE CFFF facility was maintained in a standby status with winterization, preventive maintenance and repairs accomplished as needed. Plans and preparations progressed for environmental actions needed at the site to investigate and characterize the groundwater and for removal/disposal of asbestos in the cooling tower. Work continued to progress on archiving the results of the MHD program.

GPHS-RTGs in support of the Cassini RTG Program

NASA Astrophysics Data System (ADS)

1995-04-01

The technical progress achieved during the period 26 Sep. 1994 - 2 Apr. 1995 on Contract DE-AC03-91SF-18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described herein. Monthly technical activity for the period 27 Feb. - 2 Apr. 1995 is included in this progress report. The report addresses tasks, including: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; ETG fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair; and CAGO acquisition (capital funds).

Information Extraction for System-Software Safety Analysis: Calendar Year 2008 Year-End Report

NASA Technical Reports Server (NTRS)

Malin, Jane T.

2009-01-01

This annual report describes work to integrate a set of tools to support early model-based analysis of failures and hazards due to system-software interactions. The tools perform and assist analysts in the following tasks: 1) extract model parts from text for architecture and safety/hazard models; 2) combine the parts with library information to develop the models for visualization and analysis; 3) perform graph analysis and simulation to identify and evaluate possible paths from hazard sources to vulnerable entities and functions, in nominal and anomalous system-software configurations and scenarios; and 4) identify resulting candidate scenarios for software integration testing. There has been significant technical progress in model extraction from Orion program text sources, architecture model derivation (components and connections) and documentation of extraction sources. Models have been derived from Internal Interface Requirements Documents (IIRDs) and FMEA documents. Linguistic text processing is used to extract model parts and relationships, and the Aerospace Ontology also aids automated model development from the extracted information. Visualizations of these models assist analysts in requirements overview and in checking consistency and completeness.

Smart Grid Interoperability Maturity Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Widergren, Steven E.; Levinson, Alex; Mater, J.

2010-04-28

The integration of automation associated with electricity resources (including transmission and distribution automation and demand-side resources operated by end-users) is key to supporting greater efficiencies and incorporating variable renewable resources and electric vehicles into the power system. The integration problems faced by this community are analogous to those faced in the health industry, emergency services, and other complex communities with many stakeholders. To highlight this issue and encourage communication and the development of a smart grid interoperability community, the GridWise Architecture Council (GWAC) created an Interoperability Context-Setting Framework. This "conceptual model" has been helpful to explain the importance of organizationalmore » alignment in addition to technical and informational interface specifications for "smart grid" devices and systems. As a next step to building a community sensitive to interoperability, the GWAC is investigating an interoperability maturity model (IMM) based on work done by others to address similar circumstances. The objective is to create a tool or set of tools that encourages a culture of interoperability in this emerging community. The tools would measure status and progress, analyze gaps, and prioritize efforts to improve the situation.« less

Designers' unified cost model

NASA Technical Reports Server (NTRS)

Freeman, W.; Ilcewicz, L.; Swanson, G.; Gutowski, T.

1992-01-01

The Structures Technology Program Office (STPO) at NASA LaRC has initiated development of a conceptual and preliminary designers' cost prediction model. The model will provide a technically sound method for evaluating the relative cost of different composite structural designs, fabrication processes, and assembly methods that can be compared to equivalent metallic parts or assemblies. The feasibility of developing cost prediction software in a modular form for interfacing with state-of-the-art preliminary design tools and computer aided design programs is being evaluated. The goal of this task is to establish theoretical cost functions that relate geometric design features to summed material cost and labor content in terms of process mechanics and physics. The output of the designers' present analytical tools will be input for the designers' cost prediction model to provide the designer with a database and deterministic cost methodology that allows one to trade and synthesize designs with both cost and weight as objective functions for optimization. This paper presents the team members, approach, goals, plans, and progress to date for development of COSTADE (Cost Optimization Software for Transport Aircraft Design Evaluation).

Synchrotron topography project. Progress report, January 20, 1982-October 20, 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bilello, J.C.; Chen, H.; Hmelo, A.B.

1982-01-01

The collaborators have participated in the Synchrotron Topography Project (STP) which has designed and developed instrumentation for an x-ray topography station at the National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory (BNL). The two principle instruments constructed consist of a White Beam Camera (WBC) and a Multiple Crystal Camera (MCC) with high planar collimation and wide area image coverage. It is possible to perform in-situ studies in a versatile environmental chamber equipped with a miniature mechanical testing stage for both the WBC and MCC systems. Real-time video imaging plus a rapid feed cassette holder for high resolution photographic platesmore » are available for recording topographs. Provisions are made for other types of photon detection as well as spectroscopy. The facilities for the entire station have been designed for remote operation using a LSI-11/23 plus suitable interfacing. These instruments will be described briefly and the current status of the program will be reviewed. The Appendix of this report presents titles, authors and abstracts of other technical work associated with this project during the current period.« less

The quantum computer game: citizen science

NASA Astrophysics Data System (ADS)

Damgaard, Sidse; Mølmer, Klaus; Sherson, Jacob

2013-05-01

Progress in the field of quantum computation is hampered by daunting technical challenges. Here we present an alternative approach to solving these by enlisting the aid of computer players around the world. We have previously examined a quantum computation architecture involving ultracold atoms in optical lattices and strongly focused tweezers of light. In The Quantum Computer Game (see http://www.scienceathome.org/), we have encapsulated the time-dependent Schrödinger equation for the problem in a graphical user interface allowing for easy user input. Players can then search the parameter space with real-time graphical feedback in a game context with a global high-score that rewards short gate times and robustness to experimental errors. The game which is still in a demo version has so far been tried by several hundred players. Extensions of the approach to other models such as Gross-Pitaevskii and Bose-Hubbard are currently under development. The game has also been incorporated into science education at high-school and university level as an alternative method for teaching quantum mechanics. Initial quantitative evaluation results are very positive. AU Ideas Center for Community Driven Research, CODER.

Factors shaping the evolution of electronic documentation systems

NASA Technical Reports Server (NTRS)

Dede, Christopher J.; Sullivan, Tim R.; Scace, Jacque R.

1990-01-01

The main goal is to prepare the space station technical and managerial structure for likely changes in the creation, capture, transfer, and utilization of knowledge. By anticipating advances, the design of Space Station Project (SSP) information systems can be tailored to facilitate a progression of increasingly sophisticated strategies as the space station evolves. Future generations of advanced information systems will use increases in power to deliver environmentally meaningful, contextually targeted, interconnected data (knowledge). The concept of a Knowledge Base Management System is emerging when the problem is focused on how information systems can perform such a conversion of raw data. Such a system would include traditional management functions for large space databases. Added artificial intelligence features might encompass co-existing knowledge representation schemes; effective control structures for deductive, plausible, and inductive reasoning; means for knowledge acquisition, refinement, and validation; explanation facilities; and dynamic human intervention. The major areas covered include: alternative knowledge representation approaches; advanced user interface capabilities; computer-supported cooperative work; the evolution of information system hardware; standardization, compatibility, and connectivity; and organizational impacts of information intensive environments.

75 FR 4770 - Fisheries of the Exclusive Economic Zone Off Alaska; Recordkeeping and Reporting Requirements...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-29

... of Fish and Game, and the International Pacific Halibut Commission will present a technical workshop... Language (XML) interface is designed to facilitate an exchange of landings and production data between e...

Transforming an educational virtual reality simulation into a work of fine art.

PubMed

Panaiotis; Addison, Laura; Vergara, Víctor M; Hakamata, Takeshi; Alverson, Dale C; Saiki, Stanley M; Caudell, Thomas Preston

2008-01-01

This paper outlines user interface and interaction issues, technical considerations, and problems encountered in transforming an educational VR simulation of a reified kidney nephron into an interactive artwork appropriate for a fine arts museum.

Computational Design Tool for the Synthesis and Optimization of Gel Formulations (SOGeF)

DTIC Science & Technology

2009-01-01

ACCOMPLISHMENTS 2.1 Phase I Technical Objectives TIle primary technical objective of the Phase I program was the development of a model(s) to describe the...Figure 37: Storage Modulus G’, Loss Modulus G", and Stress vs. Strain. Yield Stress ~460Pa. (Tri-ethylamine 11% Cabosil) The primary detenninant of...GUI The primary objective of this task was to design and implement a graphical user interface (GUI) for the NN algorithms and gel database files. The

Metallurgical Characterization of the Interfaces and the Damping Mechanisms in Metal Matrix Composites.

DTIC Science & Technology

1986-04-15

Technical Reports - none IL.. Publications - none 11.g. Honors, Awards - none 11.h. Participants Mr. Asok Ray ; Graduate Student working towards his...Invited Presentation at Topical or Scientific/Technical Society Conferences i) A.K. Ray and V.K. Kinra, "Measurement of Damping in Continuous Fiber...Rawal, J.H. Armstrong, M.S. Misra, A.K. Ray and V.K. Kinra, "Damping Measurements of Gr/Al Composites", to be presented at the symposium on Dynamic

The Gap That Can't Go Away: The Catch-22 of Reclassification in Monitoring the Progress of English Learners

ERIC Educational Resources Information Center

Saunders, William M.; Marcelletti, David J.

2013-01-01

When English Learners (ELs) demonstrate English language proficiency, they are reclassified as Fluent English Proficient (RFEP). Subsequently they are often left out of the analysis of EL progress because they are, technically, no longer ELs. This article examines the effects of including and excluding RFEPs from the analysis of EL progress. Based…

Bone Conduction Communication: Research Progress and Directions

DTIC Science & Technology

2017-08-16

ARL-TR-8096 ● AUG 2017 US Army Research Laboratory Bone Conduction Communication: Research Progress and Directions by Maranda...this report when it is no longer needed. Do not return it to the originator. ARL-TR-8096 ● AUG 2017 US Army Research Laboratory...Bone Conduction Communication: Research Progress and Directions by Maranda McBride North Carolina Agricultural and Technical State University

25 CFR 30.123 - What is the Bureau's role in assisting Bureau-funded schools to make AYP?

Code of Federal Regulations, 2010 CFR

2010-04-01

... EDUCATION ADEQUATE YEARLY PROGRESS Failure To Make Adequate Yearly Progress § 30.123 What is the Bureau's...-funded schools to assist them in achieving AYP. This includes technical assistance and other forms of...

25 CFR 30.123 - What is the Bureau's role in assisting Bureau-funded schools to make AYP?

Code of Federal Regulations, 2011 CFR

2011-04-01

... EDUCATION ADEQUATE YEARLY PROGRESS Failure To Make Adequate Yearly Progress § 30.123 What is the Bureau's...-funded schools to assist them in achieving AYP. This includes technical assistance and other forms of...

Black River Technical College, Exploring America's Communities. Progress Report.

ERIC Educational Resources Information Center

Black River Vocational-Technical School, Pocahontas, AR.

In 1996, Arkansas's Black River Technical College (BRTC) participated in the American Association of Community Colleges' Exploring America's Communities project, which worked to strengthen the teaching and learning of American history, literature, and culture at U.S. community colleges. The proposed centerpiece of BRTC's program is called the…

40 CFR 40.150 - Evaluation of applications.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Relevancy, coupled with the results of technical review, will provide the basis for funding recommendations... will be reviewed for technical merit by at least one reviewer within EPA and at least two reviewers.... Recommendations for continuation of funding will be based on progress toward the accomplishment of the goals set...

40 CFR 35.4235 - Are there specific provisions my group's contract(s) must contain?

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Technical Assistance Procuring A Technical Advisor Or Other Contractor with Tag Funds § 35.4235 Are there specific... progress reports; (3) Expenditures; and (4) Commitments indicating their relationship to established costs...

Missouri local technical assistance program at Missouri University of Science and Technology (formerly University of Missouri--Rolla) : annual progress report January-December 2007.

DOT National Transportation Integrated Search

2009-02-01

This annual report is a summary of the activities during 2007 for the Missouri Local Technical Assistance Program (Missouri LTAP), which is located at Missouri University of Science and Technology. The report highlights Missouri LTAPs performance ...

Global Issues in Career and Technical Fields: Internationalizing the Community College Curriculum.

ERIC Educational Resources Information Center

Peck, Shirley S.

1991-01-01

Presents a rationale for incorporating international content in both general education and career/technical fields, providing a status report on progress to date. Describes four modules prepared by Catonsville Community College (Maryland) instructors for inclusion in criminal justice, air transportation, automotive service, and electronics…

Technical and Vocational Education in Cameroon and Critical Avenues for Development

ERIC Educational Resources Information Center

Che, S. Megan

2007-01-01

Technical and vocational education (TVE) can influence development and economic progress for post-colonial societies. Some newly independent sub-Saharan African countries attempted curricular transformation that might produce a skilled workforce through widespread access to versions of TVE. In Cameroon, no such post-colonial curricular revolution…

Publications of the Jet Propulsion Laboratory, January through December 1974. [deep space network, Apollo project, information theory, and space exploration

NASA Technical Reports Server (NTRS)

1975-01-01

Formalized technical reporting is described and indexed, which resulted from scientific and engineering work performed, or managed, by the Jet Propulsion Laboratory. The five classes of publications included are technical reports, technical memorandums, articles from the bimonthly Deep Space Network Progress Report, special publications, and articles published in the open literature. The publications are indexed by author, subject, and publication type and number.

Chemical Communications

DTIC Science & Technology

2012-10-26

the need for alignment. We have also demonstrated the use of this technique with various materials as masks for silk biopolymer RIE processing and a...project. The automatization of silk solution was developed. Examination of different processing conditions for the raw material showed promise for...higher durability and higher flexibility optical substrates. Progress on interfaces was solidified. The previous findings on silk -metal interfaces

TMT approach to observatory software development process

NASA Astrophysics Data System (ADS)

Buur, Hanne; Subramaniam, Annapurni; Gillies, Kim; Dumas, Christophe; Bhatia, Ravinder

2016-07-01

The purpose of the Observatory Software System (OSW) is to integrate all software and hardware components of the Thirty Meter Telescope (TMT) to enable observations and data capture; thus it is a complex software system that is defined by four principal software subsystems: Common Software (CSW), Executive Software (ESW), Data Management System (DMS) and Science Operations Support System (SOSS), all of which have interdependencies with the observatory control systems and data acquisition systems. Therefore, the software development process and plan must consider dependencies to other subsystems, manage architecture, interfaces and design, manage software scope and complexity, and standardize and optimize use of resources and tools. Additionally, the TMT Observatory Software will largely be developed in India through TMT's workshare relationship with the India TMT Coordination Centre (ITCC) and use of Indian software industry vendors, which adds complexity and challenges to the software development process, communication and coordination of activities and priorities as well as measuring performance and managing quality and risk. The software project management challenge for the TMT OSW is thus a multi-faceted technical, managerial, communications and interpersonal relations challenge. The approach TMT is using to manage this multifaceted challenge is a combination of establishing an effective geographically distributed software team (Integrated Product Team) with strong project management and technical leadership provided by the TMT Project Office (PO) and the ITCC partner to manage plans, process, performance, risk and quality, and to facilitate effective communications; establishing an effective cross-functional software management team composed of stakeholders, OSW leadership and ITCC leadership to manage dependencies and software release plans, technical complexities and change to approved interfaces, architecture, design and tool set, and to facilitate effective communications; adopting an agile-based software development process across the observatory to enable frequent software releases to help mitigate subsystem interdependencies; defining concise scope and work packages for each of the OSW subsystems to facilitate effective outsourcing of software deliverables to the ITCC partner, and to enable performance monitoring and risk management. At this stage, the architecture and high-level design of the software system has been established and reviewed. During construction each subsystem will have a final design phase with reviews, followed by implementation and testing. The results of the TMT approach to the Observatory Software development process will only be preliminary at the time of the submittal of this paper, but it is anticipated that the early results will be a favorable indication of progress.

A Review of Organic and Inorganic Biomaterials for Neural Interfaces

PubMed Central

Fattahi, Pouria; Yang, Guang; Kim, Gloria

2015-01-01

Recent advances in nanotechnology have generated wide interest in applying nanomaterials for neural prostheses. An ideal neural interface should create seamless integration into the nervous system and performs reliably for long periods of time. As a result, many nanoscale materials not originally developed for neural interfaces become attractive candidates to detect neural signals and stimulate neurons. In this comprehensive review, an overview of state-of-the-art microelectrode technologies provided first, with focus on the material properties of these microdevices. The advancements in electro active nanomaterials are then reviewed, including conducting polymers, carbon nanotubes, graphene, silicon nanowires, and hybrid organic-inorganic nanomaterials, for neural recording, stimulation, and growth. Finally, technical and scientific challenges are discussed regarding biocompatibility, mechanical mismatch, and electrical properties faced by these nanomaterials for the development of long-lasting functional neural interfaces. PMID:24677434

A review of organic and inorganic biomaterials for neural interfaces.

PubMed

Fattahi, Pouria; Yang, Guang; Kim, Gloria; Abidian, Mohammad Reza

2014-03-26

Recent advances in nanotechnology have generated wide interest in applying nanomaterials for neural prostheses. An ideal neural interface should create seamless integration into the nervous system and performs reliably for long periods of time. As a result, many nanoscale materials not originally developed for neural interfaces become attractive candidates to detect neural signals and stimulate neurons. In this comprehensive review, an overview of state-of-the-art microelectrode technologies provided fi rst, with focus on the material properties of these microdevices. The advancements in electro active nanomaterials are then reviewed, including conducting polymers, carbon nanotubes, graphene, silicon nanowires, and hybrid organic-inorganic nanomaterials, for neural recording, stimulation, and growth. Finally, technical and scientific challenges are discussed regarding biocompatibility, mechanical mismatch, and electrical properties faced by these nanomaterials for the development of long-lasting functional neural interfaces.

Technical adequacy of growth estimates from a computer adaptive test: Implications for progress monitoring.

PubMed

Van Norman, Ethan R; Nelson, Peter M; Parker, David C

2017-09-01

Computer adaptive tests (CATs) hold promise to monitor student progress within multitiered systems of support. However, the relationship between how long and how often data are collected and the technical adequacy of growth estimates from CATs has not been explored. Given CAT administration times, it is important to identify optimal data collection schedules to minimize missed instructional time. We used simulation methodology to investigate how the duration and frequency of data collection influenced the reliability, validity, and precision of growth estimates from a math CAT. A progress monitoring dataset of 746 Grade 4, 664 Grade 5, and 400 Grade 6 students from 40 schools in the upper Midwest was used to generate model parameters. Across grades, 53% of students were female and 53% were White. Grade level was not as influential as the duration and frequency of data collection on the technical adequacy of growth estimates. Low-stakes decisions were possible after 14-18 weeks when data were collected weekly (420-540 min of assessment), 20-24 weeks when collected every other week (300-360 min of assessment), and 20-28 weeks (150-210 min of assessment) when data were collected once a month, depending on student grade level. The validity and precision of growth estimates improved when the duration and frequency of progress monitoring increased. Given the amount of time required to obtain technically adequate growth estimates in the present study, results highlight the importance of weighing the potential costs of missed instructional time relative to other types of assessments, such as curriculum-based measures. Implications for practice, research, as well as future directions are also discussed. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Human-system Interfaces to Automatic Systems: Review Guidance and Technical Basis

DOE Office of Scientific and Technical Information (OSTI.GOV)

OHara, J.M.; Higgins, J.C.

Automation has become ubiquitous in modern complex systems and commercial nuclear power plants are no exception. Beyond the control of plant functions and systems, automation is applied to a wide range of additional functions including monitoring and detection, situation assessment, response planning, response implementation, and interface management. Automation has become a 'team player' supporting plant personnel in nearly all aspects of plant operation. In light of the increasing use and importance of automation in new and future plants, guidance is needed to enable the NRC staff to conduct safety reviews of the human factors engineering (HFE) aspects of modern automation.more » The objective of the research described in this report was to develop guidance for reviewing the operator's interface with automation. We first developed a characterization of the important HFE aspects of automation based on how it is implemented in current systems. The characterization included five dimensions: Level of automation, function of automation, modes of automation, flexibility of allocation, and reliability of automation. Next, we reviewed literature pertaining to the effects of these aspects of automation on human performance and the design of human-system interfaces (HSIs) for automation. Then, we used the technical basis established by the literature to develop design review guidance. The guidance is divided into the following seven topics: Automation displays, interaction and control, automation modes, automation levels, adaptive automation, error tolerance and failure management, and HSI integration. In addition, we identified insights into the automaton design process, operator training, and operations.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steffens, H.D.; Kern, H.; Janczak, J.

The potential benefits and the current state-of-the-art in MMCs will be presented through a discussion of their processing and related aspects. The advantages and limitations of most common manufacturing techniques of fiber reinforced metals, e.g. realized property potential and commercial possibilities, will be outlined. The emphasis will be given on novel powder metallurgy techniques such as rapid solidification (e.g. atomization techniques and plasma processes) and new materials systems (e.g. intermetallic matrix composites). The technical barriers which prevent the transition of MMCs from aerospace to a wider range of applications will be highlighted, Special attention will be drawn to the relationmore » between processing parameters, fiber-matrix interface and composite properties. The challenge of composite modeling and design as well as interface controlling for successful processing utilization of MMCs will be mentioned. The benefits of use of computer techniques (databases, simulations, knowledge based systems) to aid the composite design and process control (fuzzy logic) will be shown on several examples. The technical possibilities of adaptation of interface tailoring approaches from the PMC area such as graded interphase or rubber-bumper interface will be studied. In addition, on the basis of recent forecasts by different experts on composite materials the question of the MMCs future will be discussed. Have they a chance in the next few years to meet the requirements of successful commercial applications, especially those of clients? The problems which have to be solved and options for solution will be dealt with.« less

76 FR 40707 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-11

... training and training equipment, support equipment, U.S. Government and contractor engineering, logistics... training equipment, support equipment, U.S. Government and contractor engineering, logistics, and technical... access to SSEE Increment F services via standard Service Oriented Architecture (SOA) interfaces via...

Technical note: Examining ozone deposition over seawater

EPA Science Inventory

Surface layer resistance plays an important role in determining ozone deposition velocity over sea-water and can be influenced by chemical interactions at the air-water interface. Here, we examine the effect of chemical interactions of iodide, dimethylsulfide, dissolved organic c...

24 CFR 1006.430 - Corrective and remedial action.

Code of Federal Regulations, 2011 CFR

2011-04-01

... plan; (3) Made substantial progress in carrying out its program and achieving its quantifiable goals as... to submit progress schedules for completing activities or complying with the requirements of the Act... appropriate technical assistance using existing grant funds or other available resources to overcome the...

Socio-technical systems and interaction design - 21st century relevance.

PubMed

Maguire, Martin

2014-03-01

This paper focuses on the relationship between the socio-technical system and the user-technology interface. It looks at specific aspects of the organisational context such as multiple user roles, job change, work processes and workflows, technical infrastructure, and the challenges they present for the interaction designer. The implications of trends such as more mobile and flexible working, the use of social media, and the growth of the virtual organisation, are also considered. The paper also reviews rapidly evolving technologies such as pervasive systems and artificial intelligence, and the skills that workers will need to engage with them. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Technical Challenges and Opportunities of Centralizing Space Science Mission Operations (SSMO) at NASA Goddard Space Flight Center

NASA Technical Reports Server (NTRS)

Ido, Haisam; Burns, Rich

2015-01-01

The NASA Goddard Space Science Mission Operations project (SSMO) is performing a technical cost-benefit analysis for centralizing and consolidating operations of a diverse set of missions into a unified and integrated technical infrastructure. The presentation will focus on the notion of normalizing spacecraft operations processes, workflows, and tools. It will also show the processes of creating a standardized open architecture, creating common security models and implementations, interfaces, services, automations, notifications, alerts, logging, publish, subscribe and middleware capabilities. The presentation will also discuss how to leverage traditional capabilities, along with virtualization, cloud computing services, control groups and containers, and possibly Big Data concepts.

Progress and Prospect: A Report Submitted to the Governing Board of the Maricopa County Community College District.

ERIC Educational Resources Information Center

Maricopa Technical Community Coll., Phoenix, AZ.

This two-part report seeks to outline the progress made to date by Maricopa Technical Community College (MTCC) through its first eight years of operation, and to recommend specific actions which might be taken in the future by the college to insure its continued progress and response to community needs in light of constraints on funding and…

User-centered development and testing of a monitoring system that provides feedback regarding physical functioning to elderly people

PubMed Central

Vermeulen, Joan; Neyens, Jacques CL; Spreeuwenberg, Marieke D; van Rossum, Erik; Sipers, Walther; Habets, Herbert; Hewson, David J; de Witte, Luc P

2013-01-01

Purpose To involve elderly people during the development of a mobile interface of a monitoring system that provides feedback to them regarding changes in physical functioning and to test the system in a pilot study. Methods and participants The iterative user-centered development process consisted of the following phases: (1) selection of user representatives; (2) analysis of users and their context; (3) identification of user requirements; (4) development of the interface; and (5) evaluation of the interface in the lab. Subsequently, the monitoring and feedback system was tested in a pilot study by five patients who were recruited via a geriatric outpatient clinic. Participants used a bathroom scale to monitor weight and balance, and a mobile phone to monitor physical activity on a daily basis for six weeks. Personalized feedback was provided via the interface of the mobile phone. Usability was evaluated on a scale from 1 to 7 using a modified version of the Post-Study System Usability Questionnaire (PSSUQ); higher scores indicated better usability. Interviews were conducted to gain insight into the experiences of the participants with the system. Results The developed interface uses colors, emoticons, and written and/or spoken text messages to provide daily feedback regarding (changes in) weight, balance, and physical activity. The participants rated the usability of the monitoring and feedback system with a mean score of 5.2 (standard deviation 0.90) on the modified PSSUQ. The interviews revealed that most participants liked using the system and appreciated that it signaled changes in their physical functioning. However, usability was negatively influenced by a few technical errors. Conclusion Involvement of elderly users during the development process resulted in an interface with good usability. However, the technical functioning of the monitoring system needs to be optimized before it can be used to support elderly people in their self-management. PMID:24039407

The ISACA Business Model for Information Security: An Integrative and Innovative Approach

NASA Astrophysics Data System (ADS)

von Roessing, Rolf

In recent years, information security management has matured into a professional discipline that covers both technical and managerial aspects in an organisational environment. Information security is increasingly dependent on business-driven parameters and interfaces to a variety of organisational units and departments. In contrast, common security models and frameworks have remained largely technical. A review of extant models ranging from [LaBe73] to more recent models shows that technical aspects are covered in great detail, while the managerial aspects of security are often neglected.Likewise, the business view on organisational security is frequently at odds with the demands of information security personnel or information technology management. In practice, senior and executive level management remain comparatively distant from technical requirements. As a result, information security is generally regarded as a cost factor rather than a benefit to the organisation.

Optical fiber sensors for materials and structures characterization

NASA Technical Reports Server (NTRS)

Lindner, D. K.; Claus, R. O.

1991-01-01

The final technical report on Optical Fiber Sensors for Materials and Structures Characterization, covering the period August 1990 through August 1991 is presented. Research programs in the following technical areas are described; sapphire optical fiber sensors; vibration analysis using two-mode elliptical core fibers and sensors; extrinsic Fabry-Perot interferometer development; and coatings for fluorescent-based sensor. Research progress in each of these areas was substantial, as evidenced by the technical publications which are included as appendices.

Towards the formal verification of the requirements and design of a processor interface unit: HOL listings

NASA Technical Reports Server (NTRS)

Fura, David A.; Windley, Phillip J.; Cohen, Gerald C.

1993-01-01

This technical report contains the Higher-Order Logic (HOL) listings of the partial verification of the requirements and design for a commercially developed processor interface unit (PIU). The PIU is an interface chip performing memory interface, bus interface, and additional support services for a commercial microprocessor within a fault tolerant computer system. This system, the Fault Tolerant Embedded Processor (FTEP), is targeted towards applications in avionics and space requiring extremely high levels of mission reliability, extended maintenance-free operation, or both. This report contains the actual HOL listings of the PIU verification as it currently exists. Section two of this report contains general-purpose HOL theories and definitions that support the PIU verification. These include arithmetic theories dealing with inequalities and associativity, and a collection of tactics used in the PIU proofs. Section three contains the HOL listings for the completed PIU design verification. Section 4 contains the HOL listings for the partial requirements verification of the P-Port.

A Development of Lightweight Grid Interface

NASA Astrophysics Data System (ADS)

Iwai, G.; Kawai, Y.; Sasaki, T.; Watase, Y.

2011-12-01

In order to help a rapid development of Grid/Cloud aware applications, we have developed API to abstract the distributed computing infrastructures based on SAGA (A Simple API for Grid Applications). SAGA, which is standardized in the OGF (Open Grid Forum), defines API specifications to access distributed computing infrastructures, such as Grid, Cloud and local computing resources. The Universal Grid API (UGAPI), which is a set of command line interfaces (CLI) and APIs, aims to offer simpler API to combine several SAGA interfaces with richer functionalities. These CLIs of the UGAPI offer typical functionalities required by end users for job management and file access to the different distributed computing infrastructures as well as local computing resources. We have also built a web interface for the particle therapy simulation and demonstrated the large scale calculation using the different infrastructures at the same time. In this paper, we would like to present how the web interface based on UGAPI and SAGA achieve more efficient utilization of computing resources over the different infrastructures with technical details and practical experiences.

44 CFR 206.437 - State administrative plan.

Code of Federal Regulations, 2010 CFR

2010-10-01

... requests for advances of funds and reimbursement; (vii) Monitor and evaluate the progress and completion of... technical assistance as required to subgrantee(s); (xi) Comply with the administrative and audit requirements of 44 CFR parts 13 and 206; (xii) Provide quarterly progress reports to the Regional Administrator...

25 CFR 30.122 - Must the Bureau assist a school it identified for school improvement, corrective action, or...

Code of Federal Regulations, 2010 CFR

2010-04-01

..., DEPARTMENT OF THE INTERIOR EDUCATION ADEQUATE YEARLY PROGRESS Failure To Make Adequate Yearly Progress § 30... restructuring, the Bureau must provide technical or other assistance described in 20 U.S.C. 6316(b)(4) and 20 U...

44 CFR 206.437 - State administrative plan.

Code of Federal Regulations, 2011 CFR

2011-10-01

... requests for advances of funds and reimbursement; (vii) Monitor and evaluate the progress and completion of... technical assistance as required to subgrantee(s); (xi) Comply with the administrative and audit requirements of 44 CFR parts 13 and 206; (xii) Provide quarterly progress reports to the Regional Administrator...

25 CFR 30.122 - Must the Bureau assist a school it identified for school improvement, corrective action, or...

Code of Federal Regulations, 2011 CFR

2011-04-01

..., DEPARTMENT OF THE INTERIOR EDUCATION ADEQUATE YEARLY PROGRESS Failure To Make Adequate Yearly Progress § 30... restructuring, the Bureau must provide technical or other assistance described in 20 U.S.C. 6316(b)(4) and 20 U...

Assessment Program Technical Progress Report, 1997-1998.

ERIC Educational Resources Information Center

Eickmeyer, Barbara; Hill, Stephen

This Assessment Program Progress Report (APPR) records the institutional activities that have taken place at Coconino Community College (CCC) during the 1997-98 academic year. It presents models, timelines, accomplishments, and opportunities for improvement in the assessment practices at CCC. Implementation and outcomes information is included for…

Diagnostic Efficiency of easyCBM[R] Math: Oregon. Technical Report #1009

ERIC Educational Resources Information Center

Anderson, Daniel; Alonzo, Julie; Tindal, Gerald

2010-01-01

The easyCBM[R] assessment system is an online benchmark and progress monitoring assessment system designed for use within a response to intervention framework. Educators using easyCBM[R] are often interested in using the results to predict students' state test performance. In the following technical document, we report diagnostic efficiency…

Longitudinal Surveys of Australian Youth (LSAY) 2009 Cohort: Wave 2 (2010)-- Questionnaire. Technical Report 71A

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2012

2012-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the questionnaire for the LSAY 2009 cohort Wave 2 (2010) data set.

Longitudinal Surveys of Australian Youth (LSAY) 2009 Cohort: Wave 3 (2011)--Questionnaire. Technical Report 72A

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2012

2012-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the questionnaire for the LSAY 2009 cohort Wave 3 (2011) data set.

Educational Reform and the World of Work: Italy

ERIC Educational Resources Information Center

von Blumenthal, Viktor

1977-01-01

One of a four-issue series on educational reform and the world of work in Europe, this issue discusses educational planning and secondary school reform in Italy. Topics discussed include planning and research in vocational-technical education, and the relation between acquisition of specific skills and scientific and technical progress. (Author/DB)

Longitudinal Surveys of Australian Youth (LSAY) 2009 Cohort: Wave 2 (2010)--Frequency Tables. Technical Report 71B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2012

2012-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 2009 cohort Wave 2 (2010) data set.

Higher Education in Kazakhstan and the Bologna Process

ERIC Educational Resources Information Center

Piven, G.; Pak, I.U.

2006-01-01

The constantly rising role of higher education in the twenty-first century goes hand in hand with scientific and technical progress and the global technologization of the developed countries of the world. A country's level of technical and technological development determines its economic condition, its national security, and its role in the world…

A State Response to Indian Vocational Education.

ERIC Educational Resources Information Center

McConnell, Bruce

In 1977 more than 500 Native Americans attended Wisconsin's vocational, technical and adult schools located in the state's 16 vocational-technical districts. While many problems still lack a clear identification and many new programs are needed to meet the needs of Native Americans, a great deal of progress has been made. A group of four Indians…

Analytical Chemistry Division. Annual progress report for period ending December 31, 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyon, W.S.

1981-05-01

This report is divided into: analytical methodology; mass and emission spectrometry; technical support; bio/organic analysis; nuclear and radiochemical analysis; quality assurance, safety, and tabulation of analyses; supplementary activities; and presentation of research results. Separate abstracts were prepared for the technical support, bio/organic analysis, and nuclear and radiochemical analysis. (DLC)

Mathematics Technical Report: Exercise Volume. National Assessment of Educational Progress. Report No. 04-MA-20.

ERIC Educational Resources Information Center

Education Commission of the States, Denver, CO. National Assessment of Educational Progress.

Included in Chapter 1 of this report are background information on the 1972-73 mathematics assessment; details of the computational formulas used in reporting results; and explanations of the technical documentation, exercise presentation, documentation pages, scoring guides, and data tables for released and unreleased exercises. The remainder of…

Experimentation with Computer-Assisted Instruction in Technical Education. Semi-Annual Progress Report.

ERIC Educational Resources Information Center

Mitzel, Harold E.; Brandon, George L.

A series of five reports is presented which describes the activities carried out by the Pennsylvania State University group engaged in research in computer-assisted instruction (CAI) in vocational-technical education. The reports cover the period January 1968-June 1968 and deal with: 1) prior knowledge and individualized instruction; 2) numerical…

Ford Plug-In Project: Bringing PHEVs to Market Demonstration and Validation Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

D'Annunzio, Julie; Slezak, Lee; Conley, John Jason

2014-03-26

This project is in support of our national goal to reduce our dependence on fossil fuels. By supporting efforts that contribute toward the successful mass production of plug-in hybrid electric vehicles, our nation’s transportation-related fuel consumption can be offset with energy from the grid. Over four and a half years ago, when this project was originally initiated, plug-in electric vehicles were not readily available in the mass marketplace. Through the creation of a 21 unit plug-in hybrid vehicle fleet, this program was designed to demonstrate the feasibility of the technology and to help build cross-industry familiarity with the technology andmore » interface of this technology with the grid. Ford Escape PHEV Demonstration Fleet 3 March 26, 2014 Since then, however, plug-in vehicles have become increasingly more commonplace in the market. Ford, itself, now offers an all-electric vehicle and two plug-in hybrid vehicles in North America and has announced a third plug-in vehicle offering for Europe. Lessons learned from this project have helped in these production vehicle launches and are mentioned throughout this report. While the technology of plugging in a vehicle to charge a high voltage battery with energy from the grid is now in production, the ability for vehicle-to-grid or bi-directional energy flow was farther away than originally expected. Several technical, regulatory and potential safety issues prevented progressing the vehicle-to-grid energy flow (V2G) demonstration and, after a review with the DOE, V2G was removed from this demonstration project. Also proving challenging were communications between a plug-in vehicle and the grid or smart meter. While this project successfully demonstrated the vehicle to smart meter interface, cross-industry and regulatory work is still needed to define the vehicle-to-grid communication interface.« less

Do failures in non-technical skills contribute to fatal medical accidents in Japan? A review of the 2010–2013 national accident reports

PubMed Central

Uramatsu, Masashi; Fujisawa, Yoshikazu; Mizuno, Shinya; Souma, Takahiro; Komatsubara, Akinori; Miki, Tamotsu

2017-01-01

Objectives We sought to clarify how large a proportion of fatal medical accidents can be considered to be caused by poor non-technical skills, and to support development of a policy to reduce number of such accidents by making recommendations about possible training requirements. Design Summaries of reports of fatal medical accidents, published by the Japan Medical Safety Research Organization, were reviewed individually. Three experienced clinicians and one patient safety expert conducted the reviews to determine the cause of death. Views of the patient safety expert were given additional weight in the overall determination. Setting A total of 73 summary reports of fatal medical accidents were reviewed. These reports had been submitted by healthcare organisations across Japan to the Japan Medical Safety Research Organization between April 2010 and March 2013. Primary and secondary outcome measures The cause of death in fatal medical accidents, categorised into technical skills, non-technical skills and inevitable progress of disease were evaluated. Non-technical skills were further subdivided into situation awareness, decision making, communication, team working, leadership, managing stress and coping with fatigue. Results Overall, the cause of death was identified as non-technical skills in 34 cases (46.6%), disease progression in 33 cases (45.2%) and technical skills in two cases (5.5%). In two cases, no consensual determination could be achieved. Further categorisation of cases of non-technical skills were identified as 14 cases (41.2%) of problems with situation awareness, eight (23.5%) with team working and three (8.8%) with decision making. These three subcategories, or combinations of them, were identified as the cause of death in 33 cases (97.1%). Conclusions Poor non-technical skills were considered to be a significant cause of adverse events in nearly half of the fatal medical accidents examined. Improving non-technical skills may be effective for reducing accidents, and training in particular subcategories of non-technical skills may be especially relevant. PMID:28209605

Intralaminar and Interlaminar Progressive Failure Analysis of Composite Panels with Circular Cutouts

NASA Technical Reports Server (NTRS)

Goyal, Vinay K.; Jaunky, Navin; Johnson, Eric R.; Ambur, Damodar

2002-01-01

A progressive failure methodology is developed and demonstrated to simulate the initiation and material degradation of a laminated panel due to intralaminar and interlaminar failures. Initiation of intralaminar failure can be by a matrix-cracking mode, a fiber-matrix shear mode, and a fiber failure mode. Subsequent material degradation is modeled using damage parameters for each mode to selectively reduce lamina material properties. The interlaminar failure mechanism such as delamination is simulated by positioning interface elements between adjacent sublaminates. A nonlinear constitutive law is postulated for the interface element that accounts for a multi-axial stress criteria to detect the initiation of delamination, a mixed-mode fracture criteria for delamination progression, and a damage parameter to prevent restoration of a previous cohesive state. The methodology is validated using experimental data available in the literature on the response and failure of quasi-isotropic panels with centrally located circular cutouts loaded into the postbuckling regime. Very good agreement between the progressive failure analyses and the experimental results is achieved if the failure analyses includes the interaction of intralaminar and interlaminar failures.

PSI-Center Final Progress Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jarboe, Thomas R.; Shumlak, Uri; Sovinec, Carl

This is the Final Progress Report of the Plasma Science and Innovation Center (PSI-Center) covering March 2014 through February 2017. The Center has accomplished a great deal during this period. The PSI-Center is organized into four groups: Edge and Dynamic Neutrals; Transport and Kinetic Effects; Equilibrium, Stability, and Kinetic Effects in 3D Topologies; and Interface for Validation. Each group has made good progress and the results from each group are given in detail.

Politics and governance at the interface between water and development.

PubMed

Abrams, L

2003-01-01

Water is not just a technical issue--it always has to be addressed within a complex political context. The water sector professional is generally unskilled in political processes, but political skill and awareness is needed to avoid negative politicization of water.

Human Spaceflight Architecture Model (HSFAM) Data Dictionary

NASA Technical Reports Server (NTRS)

Shishko, Robert

2016-01-01

HSFAM is a data model based on the DoDAF 2.02 data model with some for purpose extensions. These extensions are designed to permit quantitative analyses regarding stakeholder concerns about technical feasibility, configuration and interface issues, and budgetary and/or economic viability.

Old PCs: Upgrade or Abandon?

ERIC Educational Resources Information Center

Perez, Ernest

1997-01-01

Examines the practical realities of upgrading Intel personal computers in libraries, considering budgets and technical personnel availability. Highlights include adding RAM; putting in faster processor chips, including clock multipliers; new hard disks; CD-ROM speed; motherboards and interface cards; cost limits and economic factors; and…

JAGUAR developer's manual.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chan, Ethan

2011-06-01

JAGUAR (JAva GUi for Applied Research) is a Java software tool providing an advanced text editor and graphical user interface (GUI) to manipulate DAKOTA (Design Analysis Kit for Optimization and Terascale Applications) input specifications. This document focuses on the technical background necessary for a developer to understand JAGUAR.

Conversion of the TRACON operations concepts database into a formal sentence outline job task taxonomy.

DOT National Transportation Integrated Search

1995-05-01

FAA Air Traffic Control Operations Concepts Volume VII.- TRACON Controllers (1989) developed by CTA, Inc., a technical description of the duties of a TRACON air traffic control specialist (ATCS), formatted in User Interface Language, was restructured...

EUO-Based Multifunctional Heterostructures

DTIC Science & Technology

2015-06-06

magnetoresistance and the metal -insulator transition resistance ratios of doped EuO by interfacing this semiconductor with niobium; the observed effect is...general and may be applied to any metal /semiconductor interface where the semiconductor shows large Zeeman splitting under magnetic field, (2...understanding the changes in electronic structure and Fermi-surface reconstruction that occur as doped EuO progresses through the ferromagnetic metal

Meso-Scale Progressive Damage Behavior Characterization of Triaxial Braided Composites under Quasi-Static Tensile Load

NASA Astrophysics Data System (ADS)

Ren, Yiru; Zhang, Songjun; Jiang, Hongyong; Xiang, Jinwu

2018-04-01

Based on continuum damage mechanics (CDM), a sophisticated 3D meso-scale finite element (FE) model is proposed to characterize the progressive damage behavior of 2D Triaxial Braided Composites (2DTBC) with 60° braiding angle under quasi-static tensile load. The modified Von Mises strength criterion and 3D Hashin failure criterion are used to predict the damage initiation of the pure matrix and fiber tows. A combining interface damage and friction constitutive model is applied to predict the interface damage behavior. Murakami-Ohno stiffness degradation scheme is employed to predict the damage evolution process of each constituent. Coupling with the ordinary and translational symmetry boundary conditions, the tensile elastic response including tensile strength and failure strain of 2DTBC are in good agreement with the available experiment data. The numerical results show that the main failure modes of the composites under axial tensile load are pure matrix cracking, fiber and matrix tension failure in bias fiber tows, matrix tension failure in axial fiber tows and interface debonding; the main failure modes of the composites subjected to transverse tensile load are free-edge effect, matrix tension failure in bias fiber tows and interface debonding.

AIAA spacecraft GN&C interface standards initiative: Overview

NASA Technical Reports Server (NTRS)

Challoner, A. Dorian

1995-01-01

The American Institute of Aeronautics and Astronautics (AIAA) has undertaken an important standards initiative in the area of spacecraft guidance, navigation, and control (GN&C) subsystem interfaces. The objective of this effort is to establish standards that will promote interchangeability of major GN&C components, thus enabling substantially lower spacecraft development costs. Although initiated by developers of conventional spacecraft GN&C, it is anticipated that interface standards will also be of value in reducing the development costs of micro-engineered spacecraft. The standardization targets are specifically limited to interfaces only, including information (i.e. data and signal), power, mechanical, thermal, and environmental interfaces between various GN&C components and between GN&C subsystems and other subsystems. The current emphasis is on information interfaces between various hardware elements (e.g., between star trackers and flight computers). The poster presentation will briefly describe the program, including the mechanics and schedule, and will publicize the technical products as they exist at the time of the conference. In particular, the rationale for the adoption of the AS1773 fiber-optic serial data bus and the status of data interface standards at the application layer will be presented.

Systematically evaluating interfaces for RNA-seq analysis from a life scientist perspective.

PubMed

Poplawski, Alicia; Marini, Federico; Hess, Moritz; Zeller, Tanja; Mazur, Johanna; Binder, Harald

2016-03-01

RNA-sequencing (RNA-seq) has become an established way for measuring gene expression in model organisms and humans. While methods development for refining the corresponding data processing and analysis pipeline is ongoing, protocols for typical steps have been proposed and are widely used. Several user interfaces have been developed for making such analysis steps accessible to life scientists without extensive knowledge of command line tools. We performed a systematic search and evaluation of such interfaces to investigate to what extent these can indeed facilitate RNA-seq data analysis. We found a total of 29 open source interfaces, and six of the more widely used interfaces were evaluated in detail. Central criteria for evaluation were ease of configuration, documentation, usability, computational demand and reporting. No interface scored best in all of these criteria, indicating that the final choice will depend on the specific perspective of users and the corresponding weighting of criteria. Considerable technical hurdles had to be overcome in our evaluation. For many users, this will diminish potential benefits compared with command line tools, leaving room for future improvement of interfaces. © The Author 2015. Published by Oxford University Press. For Permissions, please email: journals.permissions@oup.com.

Software Implemented Fault-Tolerant (SIFT) user's guide

NASA Technical Reports Server (NTRS)

Green, D. F., Jr.; Palumbo, D. L.; Baltrus, D. W.

1984-01-01

Program development for a Software Implemented Fault Tolerant (SIFT) computer system is accomplished in the NASA LaRC AIRLAB facility using a DEC VAX-11 to interface with eight Bendix BDX 930 flight control processors. The interface software which provides this SIFT program development capability was developed by AIRLAB personnel. This technical memorandum describes the application and design of this software in detail, and is intended to assist both the user in performance of SIFT research and the systems programmer responsible for maintaining and/or upgrading the SIFT programming environment.

Big Data Discovery and Access Services through NOAA OneStop

NASA Astrophysics Data System (ADS)

Casey, K. S.; Neufeld, D.; Ritchey, N. A.; Relph, J.; Fischman, D.; Baldwin, R.

2017-12-01

The NOAA OneStop Project was created as a pathfinder effort to to improve the discovery of, access to, and usability of NOAA's vast and diverse collection of big data. OneStop is led by the NOAA/NESDIS National Centers for Environmental Information (NCEI), and is seen as a key NESDIS contribution to NOAA's open data and data stewardship efforts. OneStop consists of an entire framework of services, from storage and interoperable access services at the base, through metadata and catalog services in the middle, to a modern user interface experience at the top. Importantly, it is an open framework where external tools and services can connect at whichever level is most appropriate. Since the beta release of the OneStop user interface at the 2016 Fall AGU meeting, significant progress has been made improving and modernizing many NOAA data collections to optimize their use within the framework. In addition, OneStop has made progress implementing robust metadata management and catalog systems at the collection and granule level and improving the user experience with the web interface. This progress will be summarized and the results of extensive user testing including professional usability studies will be reviewed. Key big data technologies supporting the framework will be presented and a community input sought on the future directions of the OneStop Project.

U.S. Army weapon systems human-computer interface style guide. Version 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Avery, L.W.; O`Mara, P.A.; Shepard, A.P.

1997-12-31

A stated goal of the US Army has been the standardization of the human computer interfaces (HCIs) of its system. Some of the tools being used to accomplish this standardization are HCI design guidelines and style guides. Currently, the Army is employing a number of HCI design guidance documents. While these style guides provide good guidance for the command, control, communications, computers, and intelligence (C4I) domain, they do not necessarily represent the more unique requirements of the Army`s real time and near-real time (RT/NRT) weapon systems. The Office of the Director of Information for Command, Control, Communications, and Computers (DISC4),more » in conjunction with the Weapon Systems Technical Architecture Working Group (WSTAWG), recognized this need as part of their activities to revise the Army Technical Architecture (ATA), now termed the Joint Technical Architecture-Army (JTA-A). To address this need, DISC4 tasked the Pacific Northwest National Laboratory (PNNL) to develop an Army weapon systems unique HCI style guide, which resulted in the US Army Weapon Systems Human-Computer Interface (WSHCI) Style Guide Version 1. Based on feedback from the user community, DISC4 further tasked PNNL to revise Version 1 and publish Version 2. The intent was to update some of the research and incorporate some enhancements. This document provides that revision. The purpose of this document is to provide HCI design guidance for the RT/NRT Army system domain across the weapon systems subdomains of ground, aviation, missile, and soldier systems. Each subdomain should customize and extend this guidance by developing their domain-specific style guides, which will be used to guide the development of future systems within their subdomains.« less

Towards passive brain-computer interfaces: applying brain-computer interface technology to human-machine systems in general.

PubMed

Zander, Thorsten O; Kothe, Christian

2011-04-01

Cognitive monitoring is an approach utilizing realtime brain signal decoding (RBSD) for gaining information on the ongoing cognitive user state. In recent decades this approach has brought valuable insight into the cognition of an interacting human. Automated RBSD can be used to set up a brain-computer interface (BCI) providing a novel input modality for technical systems solely based on brain activity. In BCIs the user usually sends voluntary and directed commands to control the connected computer system or to communicate through it. In this paper we propose an extension of this approach by fusing BCI technology with cognitive monitoring, providing valuable information about the users' intentions, situational interpretations and emotional states to the technical system. We call this approach passive BCI. In the following we give an overview of studies which utilize passive BCI, as well as other novel types of applications resulting from BCI technology. We especially focus on applications for healthy users, and the specific requirements and demands of this user group. Since the presented approach of combining cognitive monitoring with BCI technology is very similar to the concept of BCIs itself we propose a unifying categorization of BCI-based applications, including the novel approach of passive BCI.

Multibody dynamics model building using graphical interfaces

NASA Technical Reports Server (NTRS)

Macala, Glenn A.

1989-01-01

In recent years, the extremely laborious task of manually deriving equations of motion for the simulation of multibody spacecraft dynamics has largely been eliminated. Instead, the dynamicist now works with commonly available general purpose dynamics simulation programs which generate the equations of motion either explicitly or implicitly via computer codes. The user interface to these programs has predominantly been via input data files, each with its own required format and peculiarities, causing errors and frustrations during program setup. Recent progress in a more natural method of data input for dynamics programs: the graphical interface, is described.

Interfacing VPSC with finite element codes. Demonstration of irradiation growth simulation in a cladding tube

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patra, Anirban; Tome, Carlos

This Milestone report shows good progress in interfacing VPSC with the FE codes ABAQUS and MOOSE, to perform component-level simulations of irradiation-induced deformation in Zirconium alloys. In this preliminary application, we have performed an irradiation growth simulation in the quarter geometry of a cladding tube. We have benchmarked VPSC-ABAQUS and VPSC-MOOSE predictions with VPSC-SA predictions to verify the accuracy of the VPSCFE interface. Predictions from the FE simulations are in general agreement with VPSC-SA simulations and also with experimental trends.

The science of neural interface systems.

PubMed

Hatsopoulos, Nicholas G; Donoghue, John P

2009-01-01

The ultimate goal of neural interface research is to create links between the nervous system and the outside world either by stimulating or by recording from neural tissue to treat or assist people with sensory, motor, or other disabilities of neural function. Although electrical stimulation systems have already reached widespread clinical application, neural interfaces that record neural signals to decipher movement intentions are only now beginning to develop into clinically viable systems to help paralyzed people. We begin by reviewing state-of-the-art research and early-stage clinical recording systems and focus on systems that record single-unit action potentials. We then address the potential for neural interface research to enhance basic scientific understanding of brain function by offering unique insights in neural coding and representation, plasticity, brain-behavior relations, and the neurobiology of disease. Finally, we discuss technical and scientific challenges faced by these systems before they are widely adopted by severely motor-disabled patients.

ECCE Toolkit: Prototyping Sensor-Based Interaction.

PubMed

Bellucci, Andrea; Aedo, Ignacio; Díaz, Paloma

2017-02-23

Building and exploring physical user interfaces requires high technical skills and hours of specialized work. The behavior of multiple devices with heterogeneous input/output channels and connectivity has to be programmed in a context where not only the software interface matters, but also the hardware components are critical (e.g., sensors and actuators). Prototyping physical interaction is hindered by the challenges of: (1) programming interactions among physical sensors/actuators and digital interfaces; (2) implementing functionality for different platforms in different programming languages; and (3) building custom electronic-incorporated objects. We present ECCE (Entities, Components, Couplings and Ecosystems), a toolkit for non-programmers that copes with these issues by abstracting from low-level implementations, thus lowering the complexity of prototyping small-scale, sensor-based physical interfaces to support the design process. A user evaluation provides insights and use cases of the kind of applications that can be developed with the toolkit.

Performance Testing of Thermal Interface Filler Materials in a Bolted Aluminum Interface Under Thermal/Vacuum Conditions

NASA Technical Reports Server (NTRS)

Glasgow, S. D.; Kittredge, K. B.

2003-01-01

A thermal interface material is one of the many tools often used as part of the thermal control scheme for space-based applications. Historically, at Marshall Space Flight Center, CHO-THERM 1671 has primarily been used for applications where an interface material was deemed necessary. However, numerous alternatives have come on the market in recent years. It was decided that a number of these materials should be tested against each other to see if there were better performing alternatives. The tests were done strictly to compare the thermal performance of the materials relative to each other under repeatable conditions and do not take into consideration other design issues, such as off-gassing, electrical conduction, isolation, etc. The purpose of this Technical Memorandum is to detail the materials tested, test apparatus, procedures, and results of these tests. The results show that there are a number of better performing alternatives now available.

Reprint of: environmental information for military planning.

PubMed

Doherty, Victoria; Croft, Darryl; Knight, Ashley

2013-11-01

A study was conducted to consider the implications of presenting Environmental Information (EI; information on current environmental features including weather, topography and visibility maps) for military planning to the growing audience of non-technical users; to provide guidance for ensuring usability and for development of a suitable EI interface, and to produce an EI concept interface mock-up to demonstrate initial design ideas. Knowledge was elicited from current EI users and providers regarding anticipated use of EI by non-specialists. This was combined with human factors and cognition expertise to produce guidance for data usability and development of an EI interface. A simple mock-up of an EI concept interface was developed. Recommendations for further development were made including application of the guidance derived, identification of a user test-bed and development of business processes. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Environmental information for military planning.

PubMed

Doherty, Victoria; Croft, Darryl; Knight, Ashley

2013-07-01

A study was conducted to consider the implications of presenting Environmental Information (EI; information on current environmental features including weather, topography and visibility maps) for military planning to the growing audience of non-technical users; to provide guidance for ensuring usability and for development of a suitable EI interface, and to produce an EI concept interface mock-up to demonstrate initial design ideas. Knowledge was elicited from current EI users and providers regarding anticipated use of EI by non-specialists. This was combined with human factors and cognition expertise to produce guidance for data usability and development of an EI interface. A simple mock-up of an EI concept interface was developed. Recommendations for further development were made including application of the guidance derived, identification of a user test-bed and development of business processes. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

ECCE Toolkit: Prototyping Sensor-Based Interaction

PubMed Central

Bellucci, Andrea; Aedo, Ignacio; Díaz, Paloma

2017-01-01

Building and exploring physical user interfaces requires high technical skills and hours of specialized work. The behavior of multiple devices with heterogeneous input/output channels and connectivity has to be programmed in a context where not only the software interface matters, but also the hardware components are critical (e.g., sensors and actuators). Prototyping physical interaction is hindered by the challenges of: (1) programming interactions among physical sensors/actuators and digital interfaces; (2) implementing functionality for different platforms in different programming languages; and (3) building custom electronic-incorporated objects. We present ECCE (Entities, Components, Couplings and Ecosystems), a toolkit for non-programmers that copes with these issues by abstracting from low-level implementations, thus lowering the complexity of prototyping small-scale, sensor-based physical interfaces to support the design process. A user evaluation provides insights and use cases of the kind of applications that can be developed with the toolkit. PMID:28241502

Preliminary Design and Evaluation of Portable Electronic Flight Progress Strips

NASA Technical Reports Server (NTRS)

Doble, Nathan A.; Hansman, R. John

2002-01-01

There has been growing interest in using electronic alternatives to the paper Flight Progress Strip (FPS) for air traffic control. However, most research has been centered on radar-based control environments, and has not considered the unique operational needs of the airport air traffic control tower. Based on an analysis of the human factors issues for control tower Decision Support Tool (DST) interfaces, a requirement has been identified for an interaction mechanism which replicates the advantages of the paper FPS (e.g., head-up operation, portability) but also enables input and output with DSTs. An approach has been developed which uses a Portable Electronic FPS that has attributes of both a paper strip and an electronic strip. The prototype flight strip system uses Personal Digital Assistants (PDAs) to replace individual paper strips in addition to a central management interface which is displayed on a desktop computer. Each PDA is connected to the management interface via a wireless local area network. The Portable Electronic FPSs replicate the core functionality of paper flight strips and have additional features which provide a heads-up interface to a DST. A departure DST is used as a motivating example. The central management interface is used for aircraft scheduling and sequencing and provides an overview of airport departure operations. This paper will present the design of the Portable Electronic FPS system as well as preliminary evaluation results.

Long-Range Trends in the Development of Higher Education in Mining

ERIC Educational Resources Information Center

Pzhevskii, V. V.

1978-01-01

Reviews the relationship between scientific and technological progress, needs of the Soviet economy, and capacities of higher education institutions in terms of the future of the mining industry. Mining specialists will have to prepare for technical progress in the extracting industries, growth in production, complex mechanization, and automation…

Progress Monitoring in Middle School Mathematics: Options and Issues

ERIC Educational Resources Information Center

Foegen, Anne

2008-01-01

This study investigated the technical features of six potential progress-monitoring measures in mathematics appropriate for use at the middle school level, including two commercially available measures for sixth-grade mathematics, two measures used in previous middle school studies, and two new measures of numeracy concepts. Five hundred…

10 CFR 600.341 - Monitoring and reporting program and financial performance.

Code of Federal Regulations, 2012 CFR

2012-01-01

... will be taken to address the deviations. (2) A final technical report if the award is for research and... dates for reports. At a minimum, requirements must include: (1) Periodic progress reports (at least... follows: (i) The program portions of the reports must address progress toward achieving program...

10 CFR 600.341 - Monitoring and reporting program and financial performance.

Code of Federal Regulations, 2014 CFR

2014-01-01

... will be taken to address the deviations. (2) A final technical report if the award is for research and... dates for reports. At a minimum, requirements must include: (1) Periodic progress reports (at least... follows: (i) The program portions of the reports must address progress toward achieving program...

10 CFR 600.341 - Monitoring and reporting program and financial performance.

Code of Federal Regulations, 2013 CFR

2013-01-01

... will be taken to address the deviations. (2) A final technical report if the award is for research and... dates for reports. At a minimum, requirements must include: (1) Periodic progress reports (at least... follows: (i) The program portions of the reports must address progress toward achieving program...

10 CFR 600.341 - Monitoring and reporting program and financial performance.

Code of Federal Regulations, 2011 CFR

2011-01-01

... will be taken to address the deviations. (2) A final technical report if the award is for research and... dates for reports. At a minimum, requirements must include: (1) Periodic progress reports (at least... follows: (i) The program portions of the reports must address progress toward achieving program...

Nuclear waste management. Semiannual progress report, October 1982-March 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chikalla, T.D.; Powell, J.A.

1983-06-01

This document is one of a series of technical progress reports designed to report radioactive waste management programs at the Pacific Northwest Laboratory. Accomplishments in the following programs are reported: waste stabilization; Materials Characterization Center; waste isolation; low-level waste management; remedial action; and supporting studies.

Advancing Stage 2 Research on Measures for Monitoring Kindergarten Reading Progress

ERIC Educational Resources Information Center

Clemens, Nathan H.; Soohoo, Michelle M.; Wiley, Colby P.; Hsiao, Yu-Yu; Estrella, Ivonne; Allee-Smith, Paula J.; Yoon, Myeongsun

2018-01-01

Although several measures exist for frequently monitoring early reading progress, little research has specifically investigated their technical properties when administered on a frequent basis with kindergarten students. In this study, kindergarten students (N = 137) of whom the majority was receiving supplemental intervention for reading skills…

Fuselage Versus Subcomponent Panel Response Correlation Based on ABAQUS Explicit Progressive Damage Analysis Tools

NASA Technical Reports Server (NTRS)

Gould, Kevin E.; Satyanarayana, Arunkumar; Bogert, Philip B.

2016-01-01

Analysis performed in this study substantiates the need for high fidelity vehicle level progressive damage analyses (PDA) structural models for use in the verification and validation of proposed sub-scale structural models and to support required full-scale vehicle level testing. PDA results are presented that capture and correlate the responses of sub-scale 3-stringer and 7-stringer panel models and an idealized 8-ft diameter fuselage model, which provides a vehicle level environment for the 7-stringer sub-scale panel model. Two unique skin-stringer attachment assumptions are considered and correlated in the models analyzed: the TIE constraint interface versus the cohesive element (COH3D8) interface. Evaluating different interfaces allows for assessing a range of predicted damage modes, including delamination and crack propagation responses. Damage models considered in this study are the ABAQUS built-in Hashin procedure and the COmplete STress Reduction (COSTR) damage procedure implemented through a VUMAT user subroutine using the ABAQUS/Explicit code.

Pervasive brain monitoring and data sharing based on multi-tier distributed computing and linked data technology

PubMed Central

Zao, John K.; Gan, Tchin-Tze; You, Chun-Kai; Chung, Cheng-En; Wang, Yu-Te; Rodríguez Méndez, Sergio José; Mullen, Tim; Yu, Chieh; Kothe, Christian; Hsiao, Ching-Teng; Chu, San-Liang; Shieh, Ce-Kuen; Jung, Tzyy-Ping

2014-01-01

EEG-based Brain-computer interfaces (BCI) are facing basic challenges in real-world applications. The technical difficulties in developing truly wearable BCI systems that are capable of making reliable real-time prediction of users' cognitive states in dynamic real-life situations may seem almost insurmountable at times. Fortunately, recent advances in miniature sensors, wireless communication and distributed computing technologies offered promising ways to bridge these chasms. In this paper, we report an attempt to develop a pervasive on-line EEG-BCI system using state-of-art technologies including multi-tier Fog and Cloud Computing, semantic Linked Data search, and adaptive prediction/classification models. To verify our approach, we implement a pilot system by employing wireless dry-electrode EEG headsets and MEMS motion sensors as the front-end devices, Android mobile phones as the personal user interfaces, compact personal computers as the near-end Fog Servers and the computer clusters hosted by the Taiwan National Center for High-performance Computing (NCHC) as the far-end Cloud Servers. We succeeded in conducting synchronous multi-modal global data streaming in March and then running a multi-player on-line EEG-BCI game in September, 2013. We are currently working with the ARL Translational Neuroscience Branch to use our system in real-life personal stress monitoring and the UCSD Movement Disorder Center to conduct in-home Parkinson's disease patient monitoring experiments. We shall proceed to develop the necessary BCI ontology and introduce automatic semantic annotation and progressive model refinement capability to our system. PMID:24917804

Mathematical challenges from theoretical/computational chemistry

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-12-31

The committee believes that this report has relevance and potentially valuable suggestions for a wide range of readers. Target audiences include: graduate departments in the mathematical and chemical sciences; federal and private agencies that fund research in the mathematical and chemical sciences; selected industrial and government research and development laboratories; developers of software and hardware for computational chemistry; and selected individual researchers. Chapter 2 of this report covers some history of computational chemistry for the nonspecialist, while Chapter 3 illustrates the fruits of some past successful cross-fertilization between mathematical scientists and computational/theoretical chemists. In Chapter 4 the committee has assembledmore » a representative, but not exhaustive, survey of research opportunities. Most of these are descriptions of important open problems in computational/theoretical chemistry that could gain much from the efforts of innovative mathematical scientists, written so as to be accessible introductions to the nonspecialist. Chapter 5 is an assessment, necessarily subjective, of cultural differences that must be overcome if collaborative work is to be encouraged between the mathematical and the chemical communities. Finally, the report ends with a brief list of conclusions and recommendations that, if followed, could promote accelerated progress at this interface. Recognizing that bothersome language issues can inhibit prospects for collaborative research at the interface between distinctive disciplines, the committee has attempted throughout to maintain an accessible style, in part by using illustrative boxes, and has included at the end of the report a glossary of technical terms that may be familiar to only a subset of the target audiences listed above.« less

Pervasive brain monitoring and data sharing based on multi-tier distributed computing and linked data technology.

PubMed

Zao, John K; Gan, Tchin-Tze; You, Chun-Kai; Chung, Cheng-En; Wang, Yu-Te; Rodríguez Méndez, Sergio José; Mullen, Tim; Yu, Chieh; Kothe, Christian; Hsiao, Ching-Teng; Chu, San-Liang; Shieh, Ce-Kuen; Jung, Tzyy-Ping

2014-01-01

EEG-based Brain-computer interfaces (BCI) are facing basic challenges in real-world applications. The technical difficulties in developing truly wearable BCI systems that are capable of making reliable real-time prediction of users' cognitive states in dynamic real-life situations may seem almost insurmountable at times. Fortunately, recent advances in miniature sensors, wireless communication and distributed computing technologies offered promising ways to bridge these chasms. In this paper, we report an attempt to develop a pervasive on-line EEG-BCI system using state-of-art technologies including multi-tier Fog and Cloud Computing, semantic Linked Data search, and adaptive prediction/classification models. To verify our approach, we implement a pilot system by employing wireless dry-electrode EEG headsets and MEMS motion sensors as the front-end devices, Android mobile phones as the personal user interfaces, compact personal computers as the near-end Fog Servers and the computer clusters hosted by the Taiwan National Center for High-performance Computing (NCHC) as the far-end Cloud Servers. We succeeded in conducting synchronous multi-modal global data streaming in March and then running a multi-player on-line EEG-BCI game in September, 2013. We are currently working with the ARL Translational Neuroscience Branch to use our system in real-life personal stress monitoring and the UCSD Movement Disorder Center to conduct in-home Parkinson's disease patient monitoring experiments. We shall proceed to develop the necessary BCI ontology and introduce automatic semantic annotation and progressive model refinement capability to our system.

USDI DCS technical support: Mississippi Test Facility

NASA Technical Reports Server (NTRS)

Preble, D. M.

1975-01-01

The objective of the technical support effort is to provide hardware and data processing support to DCS users so that application of the system may be simply and effectively implemented. Technical support at Mississippi Test Facility (MTF) is concerned primarily with on-site hardware. The first objective of the DCP hardware support was to assure that standard measuring apparatus and techniques used by the USGS could be adapted to the DCS. The second objective was to try to standardize the miscellaneous variety of parameters into a standard instrument set. The third objective was to provide the necessary accessories to simplify the use and complement the capabilities of the DCP. The standard USGS sites have been interfaced and are presently operating. These sites are stream gauge, ground water level and line operated quality of water. Evapotranspiration, meteorological and battery operated quality of water sites are planned for near future DCP operation. Three accessories which are under test or development are the Chu antenna, solar power supply and add-on memory. The DCP has proven to be relatively easy to interface with many monitors. The large antenna is awkward to install and transport. The DCS has met the original requirements well; it has and is proving that an operation, satellite-based data collection system is feasible.

Tiger Team Assessment of the Los Alamos National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-11-01

The purpose of the safety and health assessment was to determine the effectiveness of representative safety and health programs at the Los Alamos National Laboratory (LANL). Within the safety and health programs at LANL, performance was assessed in the following technical areas: Organization and Administration, Quality Verification, Operations, Maintenance, Training and Certification, Auxiliary Systems, Emergency Preparedness, Technical Support, Packaging and Transportation, Nuclear Criticality Safety, Security/Safety Interface, Experimental Activities, Site/Facility Safety Review, Radiological Protection, Personnel Protection, Worker Safety and Health (OSHA) Compliance, Fire Protection, Aviation Safety, Explosives Safety, Natural Phenomena, and Medical Services.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This report summarizes geothermal technical assistance, R&D, and technology transfer activities of the Geo-Heat Center. It describes 95 contacts with parties during this period related to technical assistance with goethermal direct heat projects. Areas dealt with include geothermal heat pumps, space heating, greenhouses, aquaculture, equipment, economics, and resources. Research activities are summarized on geothermal district heating system cost evaluation and silica waste utilization project. Outreach activities include publication of a geothermal direct use Bulletin, dissemination of information, goethermal library, technical papers and seminars, and progress monitor reports on geothermal resources and utilization.

Rational load rating of deck-girder bridges with girder end shear cracks in reverse orientation : technical summary.

DOT National Transportation Integrated Search

2017-04-01

A user interface creates a grillage model of an existing bridge and places various rating trucks on the : bridge. Equivalent flexibility analysis distributes truck live loads within deck panels to surrounding : girders and diaphragms. Stiffness matri...

25 CFR 547.11 - What are the minimum technical standards for money and credit handling?

Code of Federal Regulations, 2014 CFR

2014-04-01

... interface is: (i) Involved in the play of a game; (ii) In audit mode, recall mode or any test mode; (iii... specifically designed to prevent repetition of validation numbers; and (B) Has some form of checkcode or other...

25 CFR 547.11 - What are the minimum technical standards for money and credit handling?

Code of Federal Regulations, 2013 CFR

2013-04-01

... interface is: (i) Involved in the play of a game; (ii) In audit mode, recall mode or any test mode; (iii... specifically designed to prevent repetition of validation numbers; and (B) Has some form of checkcode or other...

Comparison of Instructors' and Students' Perceptions of the Effectiveness of Online Courses

ERIC Educational Resources Information Center

Seok, Soonhwa; DaCosta, Boaventura; Kinsell, Carolyn; Tung, Chan K.

2010-01-01

This study used an extensive online course evaluation inventory to analyze the subjects' perceptions of course effectiveness in the following subscales: flexibility, user interface, navigation, getting started, technical assistance, course management, universal design, communications, instructional design, and content. Survey results compared…

STAR - Copperhead Interface.

DTIC Science & Technology

1981-03-01

elements which fall outside the original box initiate new clusters. 65 ELL. CH ECK This routine provides the calculation which determines if a target...US Air Force Project Rand Report 3-152b-PR, March 197 88 INITIAL DISTRIBUTION LIST 1o. Copies 1. Defense Technical Information Center 2 Cameron

The Use of Dynamic Stochastic Social Behavior Models to Produce Likelihood Functions for Risk Modeling of Proliferation and Terrorist Attacks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, Jonathan; Thompson, Sandra E.; Brothers, Alan J.

The ability to estimate the likelihood of future events based on current and historical data is essential to the decision making process of many government agencies. Successful predictions related to terror events and characterizing the risks will support development of options for countering these events. The predictive tasks involve both technical and social component models. The social components have presented a particularly difficult challenge. This paper outlines some technical considerations of this modeling activity. Both data and predictions associated with the technical and social models will likely be known with differing certainties or accuracies – a critical challenge is linkingmore » across these model domains while respecting this fundamental difference in certainty level. This paper will describe the technical approach being taken to develop the social model and identification of the significant interfaces between the technical and social modeling in the context of analysis of diversion of nuclear material.« less

Materials interface engineering for solution-processed photovoltaics.

PubMed

Graetzel, Michael; Janssen, René A J; Mitzi, David B; Sargent, Edward H

2012-08-16

Advances in solar photovoltaics are urgently needed to increase the performance and reduce the cost of harvesting solar power. Solution-processed photovoltaics are cost-effective to manufacture and offer the potential for physical flexibility. Rapid progress in their development has increased their solar-power conversion efficiencies. The nanometre (electron) and micrometre (photon) scale interfaces between the crystalline domains that make up solution-processed solar cells are crucial for efficient charge transport. These interfaces include large surface area junctions between photoelectron donors and acceptors, the intralayer grain boundaries within the absorber, and the interfaces between photoactive layers and the top and bottom contacts. Controlling the collection and minimizing the trapping of charge carriers at these boundaries is crucial to efficiency.

The PRISM project

NASA Astrophysics Data System (ADS)

Guilyardi, E.

2003-04-01

The European Union's PRISM infrastructure project (PRogram for Integrated earth System Modelling) aims at designing a flexible environment to easily assemble and run Earth System Models (http://prism.enes.org). Europe's widely distributed modelling expertise is both a strength and a challenge. Recognizing this, the PRISM project aims at developing an efficient shared modelling software infrastructure for climate scientists, providing them with an opportunity for greater focus on scientific issues, including the necessary scientific diversity (models and approaches). The proposed PRISM system includes 1) the use - or definition - and promotion of scientific and technical standards to increase component modularity, 2) an end-to-end software environment (coupler, user interface, diagnostics) to launch, monitor and analyze complex Earth System Models built around the existing and future community models, 3) testing and quality standards to ensure HPC performance on a variety of platforms and 4) community wide inputs and requirements capture in all stages of system specifications and design through user/developers meetings, workshops and thematic schools. This science driven project, led by 22 institutes* and started December 1st 2001, benefits from a unique gathering of scientific and technical expertise. More than 30 models (both global and regional) have expressed interest to be part of the PRISM system and 6 types of components have been identified: atmosphere, atmosphere chemistry, land surface, ocean, sea ice and ocean biochemistry. Progress and overall architecture design will be presented. * MPI-Met (Coordinator), KNMI (co-coordinator), MPI-M&D, Met Office, University of Reading, IPSL, Meteo-France, CERFACS, DMI, SMHI, NERSC, ETH Zurich, INGV, MPI-BGC, PIK, ECMWF, UCL-ASTR, NEC, FECIT, SGI, SUN, CCRLE

THE DEVELOPMENT OF ACHIEVEMENT MEASURES FOR TRADE AND TECHNICAL EDUCATION. PROGRESS REPORT NUMBER THREE.

ERIC Educational Resources Information Center

BALDWIN, THOMAS S.

DURING THIS PERIOD FROM SEPTEMBER 1 THROUGH NOVEMBER 30, 1966, 35 FIELD CONSULTANTS COMPLETED ANALYSIS OF THEIR INDIVIDUAL TRADE AND TECHNICAL CURRICULUMS. THESE ANALYSES WERE DEVELOPED INTO AN OUTLINE TO SERVE AS A GUIDE FOR DEVELOPING ACHIEVEMENT TESTS. THE FINAL OUTLINE WAS DIVIDED INTO AS MANY DIFFERENT AREAS AS THE CONSULTANTS FELT NECESSARY…

25 CFR 547.7 - What are the minimum technical hardware standards applicable to Class II gaming systems?

Code of Federal Regulations, 2011 CFR

2011-04-01

... OF CLASS II GAMES § 547.7 What are the minimum technical hardware standards applicable to Class II... the game, and are specially manufactured or proprietary and not off-the-shelf, shall display a unique... outcome or integrity of any game, progressive award, financial instrument, cashless transaction, voucher...

25 CFR 547.7 - What are the minimum technical hardware standards applicable to Class II gaming systems?

Code of Federal Regulations, 2012 CFR

2012-04-01

... OF CLASS II GAMES § 547.7 What are the minimum technical hardware standards applicable to Class II... the game, and are specially manufactured or proprietary and not off-the-shelf, shall display a unique... outcome or integrity of any game, progressive award, financial instrument, cashless transaction, voucher...

25 CFR 547.7 - What are the minimum technical hardware standards applicable to Class II gaming systems?

Code of Federal Regulations, 2010 CFR

2010-04-01

... OF CLASS II GAMES § 547.7 What are the minimum technical hardware standards applicable to Class II... the game, and are specially manufactured or proprietary and not off-the-shelf, shall display a unique... outcome or integrity of any game, progressive award, financial instrument, cashless transaction, voucher...

Diagnostic Efficiency of easyCBM[R] Math: Washington State. Technical Report #1008

ERIC Educational Resources Information Center

Anderson, Daniel; Alonzo, Julie; Tindal, Gerald

2010-01-01

easyCBM[R] is an online benchmark and progress monitoring assessment system designed for use within a response to intervention framework. Educators using easyCBM[R] are often interested in using the results to predict students' state test performance. In the following technical document, we report diagnostic efficiency statistics using a sample…

U.S. TIMSS and PIRLS 2011 Technical Report and User's Guide. NCES 2013-046

ERIC Educational Resources Information Center

Kastberg, David; Roey, Stephen; Ferraro, David; Lemanski, Nita; Erberber, Ebru

2013-01-01

The "U.S. TIMSS and PIRLS 2011 Technical Report and User's Guide" provides an overview of the design and implementation of the Trends in International Mathematics and Science Study (TIMSS) 2011 and the Progress in International Reading Literacy Study (PIRLS) 2011 in the United States and the nine participating benchmarking states:…

Longitudinal Surveys of Australian Youth (LSAY) 1998 Cohort: Wave 12 (2009)--Questionnaire. Technical Report 58A

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the questionnaire for the LSAY 1998 cohort Wave 12 (2009) data set. [For the accompanying frequency tables, "Longitudinal Surveys…

The Development of the easyCBM CCSS Reading Assessments: Grade 3. Technical Report #1221

ERIC Educational Resources Information Center

Alonzo, Julie; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we document the development and piloting of easyCBM reading measures aligned to the Common Core State Standards, designed for use in screening students at risk for reading difficulty and monitoring their progress as they develop reading skills. The measures, which assess students' ability to respond to…

Developing Technical Writing Skills in the Physical Chemistry Laboratory: A Progressive Approach Employing Peer Review

ERIC Educational Resources Information Center

Gragson, Derek E.; Hagen, John P.

2010-01-01

Writing formal "journal-style" lab reports is often one of the requirements chemistry and biochemistry students encounter in the physical chemistry laboratory. Helping students improve their technical writing skills is the primary reason this type of writing is a requirement in the physical chemistry laboratory. Developing these skills is an…

Quality and Quality Assurance in Technical and Vocational Education and Training. Thematic Studies

ERIC Educational Resources Information Center

Seyfried, Erwin

2008-01-01

In many countries in both the Mediterranean region and the European Union (EU), interest in the quality of, and improvements to, technical and vocational education and training (TVET) systems has increased progressively in recent years. The main reason underlying this interest is a growing awareness of the key role played by education and training…

The Development of CBM Vocabulary Measures: Grade 4. Technical Report #1211

ERIC Educational Resources Information Center

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 7. Technical Report #1214

ERIC Educational Resources Information Center

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 5. Technical Report #1212

ERIC Educational Resources Information Center

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 8. Technical Report #1215

ERIC Educational Resources Information Center

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 2. Technical Report #1209

ERIC Educational Resources Information Center

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 3. Technical Report #1210

ERIC Educational Resources Information Center

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

The Development of CBM Vocabulary Measures: Grade 6. Technical Report # 1213

ERIC Educational Resources Information Center

Alonzo, Julie; Anderson, Daniel; Park, Bitnara Jasmine; Tindal, Gerald

2012-01-01

In this technical report, we describe the development and piloting of a series of vocabulary assessments intended for use with students in grades two through eight. These measures, available as part of easyCBM[TM], an online progress monitoring and benchmark/screening assessment system, were developed in 2010 and administered to approximately 1200…

Application of Communications Satellites to Educational Development. Final Technical Report, September 1, 1969-August 31, 1975.

ERIC Educational Resources Information Center

Morgan, Robert P.

Research is summarized in a brief final report built around a four-section bibliography. The first section lists periodic progress reports and articles which provide an overview of the program, including articles which pertain primarily to educational rather than technical aspects of satellite utilization. Theses carried out in the fields of…

Interfaces of high-efficiency kesterite Cu2ZnSnS(e)4 thin film solar cells

NASA Astrophysics Data System (ADS)

Gao, Shoushuai; Jiang, Zhenwu; Wu, Li; Ao, Jianping; Zeng, Yu; Sun, Yun; Zhang, Yi

2018-01-01

Cu2ZnSnS(e)4 (CZTS(e)) solar cells have attracted much attention due to the elemental abundance and the non-toxicity. However, the record efficiency of 12.6% for Cu2ZnSn(S,Se)4 (CZTSSe) solar cells is much lower than that of Cu(In,Ga)Se2 (CIGS) solar cells. One crucial reason is the recombination at interfaces. In recent years, large amount investigations have been done to analyze the interfacial problems and improve the interfacial properties via a variety of methods. This paper gives a review of progresses on interfaces of CZTS(e) solar cells, including: (1) the band alignment optimization at buffer/CZTS(e) interface, (2) tailoring the thickness of MoS(e)2 interfacial layers between CZTS(e) absorber and Mo back contact, (3) the passivation of rear interface, (4) the passivation of front interface, and (5) the etching of secondary phases.

Technical efficiency and productivity of Chinese county hospitals: an exploratory study in Henan province, China.

PubMed

Cheng, Zhaohui; Tao, Hongbing; Cai, Miao; Lin, Haifeng; Lin, Xiaojun; Shu, Qin; Zhang, Ru-Ning

2015-09-09

Chinese county hospitals have been excessively enlarging their scale during the healthcare reform since 2009. The purpose of this paper is to examine the technical efficiency and productivity of county hospitals during the reform process, and to determine whether, and how, efficiency is affected by various factors. 114 sample county hospitals were selected from Henan province, China, from 2010 to 2012. Data envelopment analysis was employed to estimate the technical and scale efficiency of sample hospitals. The Malmquist index was used to calculate productivity changes over time. Tobit regression was used to regress against 4 environmental factors and 5 institutional factors that affected the technical efficiency. (1) 112 (98.2%), 112 (98.2%) and 104 (91.2%) of the 114 sample hospitals ran inefficiently in 2010, 2011 and 2012, with average technical efficiency of 0.697, 0.748 and 0.790, respectively. (2) On average, during 2010-2012, productivity of sample county hospitals increased by 7.8%, which was produced by the progress in technical efficiency changes and technological changes of 0.9% and 6.8%, respectively. (3) Tobit regression analysis indicated that government subsidy, hospital size with above 618 beds and average length of stay assumed a negative sign with technical efficiency; bed occupancy rate, ratio of beds to nurses and ratio of nurses to physicians assumed a positive sign with technical efficiency. There was considerable space for technical efficiency improvement in Henan county hospitals. During 2010-2012, sample hospitals experienced productivity progress; however, the adverse change in pure technical efficiency should be emphasised. Moreover, according to the Tobit results, policy interventions that strictly supervise hospital bed scale, shorten the average length of stay and coordinate the proportion among physicians, nurses and beds, would benefit hospital efficiency. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Technical efficiency and productivity of Chinese county hospitals: an exploratory study in Henan province, China

PubMed Central

Cheng, Zhaohui; Tao, Hongbing; Cai, Miao; Lin, Haifeng; Lin, Xiaojun; Shu, Qin; Zhang, Ru-ning

2015-01-01

Objectives Chinese county hospitals have been excessively enlarging their scale during the healthcare reform since 2009. The purpose of this paper is to examine the technical efficiency and productivity of county hospitals during the reform process, and to determine whether, and how, efficiency is affected by various factors. Setting and participants 114 sample county hospitals were selected from Henan province, China, from 2010 to 2012. Outcome measures Data envelopment analysis was employed to estimate the technical and scale efficiency of sample hospitals. The Malmquist index was used to calculate productivity changes over time. Tobit regression was used to regress against 4 environmental factors and 5 institutional factors that affected the technical efficiency. Results (1) 112 (98.2%), 112 (98.2%) and 104 (91.2%) of the 114 sample hospitals ran inefficiently in 2010, 2011 and 2012, with average technical efficiency of 0.697, 0.748 and 0.790, respectively. (2) On average, during 2010–2012, productivity of sample county hospitals increased by 7.8%, which was produced by the progress in technical efficiency changes and technological changes of 0.9% and 6.8%, respectively. (3) Tobit regression analysis indicated that government subsidy, hospital size with above 618 beds and average length of stay assumed a negative sign with technical efficiency; bed occupancy rate, ratio of beds to nurses and ratio of nurses to physicians assumed a positive sign with technical efficiency. Conclusions There was considerable space for technical efficiency improvement in Henan county hospitals. During 2010–2012, sample hospitals experienced productivity progress; however, the adverse change in pure technical efficiency should be emphasised. Moreover, according to the Tobit results, policy interventions that strictly supervise hospital bed scale, shorten the average length of stay and coordinate the proportion among physicians, nurses and beds, would benefit hospital efficiency. PMID:26353864

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gauglitz, Phillip A.; Bontha, Jagannadha R.; Daniel, Richard C.

The Hanford Waste Treatment and Immobilization Plant (WTP) is currently being designed and constructed to pretreat and vitrify a large portion of the waste in the 177 underground waste storage tanks at the Hanford Site. A number of technical issues related to the design of the pretreatment facility (PTF) of the WTP have been identified. These issues must be resolved prior to the U.S. Department of Energy (DOE) Office of River Protection (ORP) reaching a decision to proceed with engineering, procurement, and construction activities for the PTF. One of the issues is Technical Issue T1 - Hydrogen Gas Release frommore » Vessels (hereafter referred to as T1). The focus of T1 is identifying controls for hydrogen release and completing any testing required to close the technical issue. In advance of selecting specific controls for hydrogen gas safety, a number of preliminary technical studies were initiated to support anticipated future testing and to improve the understanding of hydrogen gas generation, retention, and release within PTF vessels. These activities supported the development of a plan defining an overall strategy and approach for addressing T1 and achieving technical endpoints identified for T1. Preliminary studies also supported the development of a test plan for conducting testing and analysis to support closing T1. Both of these plans were developed in advance of selecting specific controls, and in the course of working on T1 it was decided that the testing and analysis identified in the test plan were not immediately needed. However, planning activities and preliminary studies led to significant technical progress in a number of areas. This report summarizes the progress to date from the preliminary technical studies. The technical results in this report should not be used for WTP design or safety and hazards analyses and technical results are marked with the following statement: “Preliminary Technical Results for Planning – Not to be used for WTP Design or Safety Analyses.”« less

Technical tips: Electrode application and preventing skin breakdown techniques.

PubMed

Berlin, Fira; Carlile, Jennifer A; de Burgo, Maria I; Rochon, Adrienne; Wagner, Esperanza E; Sellers, Martha C; Worrell, Amanda R; Andal, E Lauren C; Woods, Latina R

2011-09-01

The recording electrodes including their precise location, their ability to record during movements that can be intense during a convulsive seizure, and their capability to record for several days without causing skin breakdown are an integral part of long-term EEG recording. Many of the facets of EEG technology have changed dramatically with the introduction of digital EEG. But the electrode and the electrode/skin interface have not had many dramatic changes. The technologist still looks for ways to ensure correct electrode placement, good recording capabilities, and a patient with healthy skin when the electrodes are removed. This Technical Tips features ideas and experiences from several technologists. These technologists express suggestions and opinions which are accepted in Technical Tips.

Evolving the Land Information System into a Cloud Computing Service

DOE Office of Scientific and Technical Information (OSTI.GOV)

Houser, Paul R.

The Land Information System (LIS) was developed to use advanced flexible land surface modeling and data assimilation frameworks to integrate extremely large satellite- and ground-based observations with advanced land surface models to produce continuous high-resolution fields of land surface states and fluxes. The resulting fields are extremely useful for drought and flood assessment, agricultural planning, disaster management, weather and climate forecasting, water resources assessment, and the like. We envisioned transforming the LIS modeling system into a scientific cloud computing-aware web and data service that would allow clients to easily setup and configure for use in addressing large water management issues.more » The focus of this Phase 1 project was to determine the scientific, technical, commercial merit and feasibility of the proposed LIS-cloud innovations that are currently barriers to broad LIS applicability. We (a) quantified the barriers to broad LIS utility and commercialization (high performance computing, big data, user interface, and licensing issues); (b) designed the proposed LIS-cloud web service, model-data interface, database services, and user interfaces; (c) constructed a prototype LIS user interface including abstractions for simulation control, visualization, and data interaction, (d) used the prototype to conduct a market analysis and survey to determine potential market size and competition, (e) identified LIS software licensing and copyright limitations and developed solutions, and (f) developed a business plan for development and marketing of the LIS-cloud innovation. While some significant feasibility issues were found in the LIS licensing, overall a high degree of LIS-cloud technical feasibility was found.« less

Developing a strategy and closure criteria for radioactive and mixed waste sites in the ORNL remedial action program: Regulatory interface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trabalka, J.R.

1987-09-01

Some options for stabilization and treatment of contaminated sites can theoretically provide a once-and-for-all solution (e.g., removal or destruction of contaminants). Most realizable options, however, leave contaminants in place (in situ), potentially isolated by physical or chemical, but more typically, by hydrologic measures. As a result of the dynamic nature of the interactions between contaminants, remedial measures, and the environment, in situ stablization measures are likely to have limited life spans, and maintenance and monitoring of performance become an essential part of the scheme. The length of formal institutional control over the site and related questions about future uses ofmore » the land and waters are of paramount importance. Unique features of the ORNL site and environs appear to be key ingredients in achieving the very long term institutional control necessary for successful financing and implementation of in situ stabilization. Some formal regulatory interface is necessary to ensure that regulatory limitations and new guidance which can affect planning and implementation of the ORNL Remedial Action Program are communicated to ORNL staff and potential technical and financial limitations which can affect schedules or alternatives for achievement of long-term site stabilization and the capability to meet environmental regulations are provided to regulatory bodies as early as possible. Such an interface should allow decisions on closure criteria to be based primarily on technical merit and protection of human health and the environment. A plan for interfacing with federal and state regulatory authorities is described. 93 refs., 1 fig., 4 tabs.« less

Update On the Status of the FLUKA Monte Carlo Transport Code*

NASA Technical Reports Server (NTRS)

Ferrari, A.; Lorenzo-Sentis, M.; Roesler, S.; Smirnov, G.; Sommerer, F.; Theis, C.; Vlachoudis, V.; Carboni, M.; Mostacci, A.; Pelliccioni, M.

2006-01-01

The FLUKA Monte Carlo transport code is a well-known simulation tool in High Energy Physics. FLUKA is a dynamic tool in the sense that it is being continually updated and improved by the authors. We review the progress achieved since the last CHEP Conference on the physics models, some technical improvements to the code and some recent applications. From the point of view of the physics, improvements have been made with the extension of PEANUT to higher energies for p, n, pi, pbar/nbar and for nbars down to the lowest energies, the addition of the online capability to evolve radioactive products and get subsequent dose rates, upgrading of the treatment of EM interactions with the elimination of the need to separately prepare preprocessed files. A new coherent photon scattering model, an updated treatment of the photo-electric effect, an improved pair production model, new photon cross sections from the LLNL Cullen database have been implemented. In the field of nucleus-- nucleus interactions the electromagnetic dissociation of heavy ions has been added along with the extension of the interaction models for some nuclide pairs to energies below 100 MeV/A using the BME approach, as well as the development of an improved QMD model for intermediate energies. Both DPMJET 2.53 and 3 remain available along with rQMD 2.4 for heavy ion interactions above 100 MeV/A. Technical improvements include the ability to use parentheses in setting up the combinatorial geometry, the introduction of pre-processor directives in the input stream. a new random number generator with full 64 bit randomness, new routines for mathematical special functions (adapted from SLATEC). Finally, work is progressing on the deployment of a user-friendly GUI input interface as well as a CAD-like geometry creation and visualization tool. On the application front, FLUKA has been used to extensively evaluate the potential space radiation effects on astronauts for future deep space missions, the activation dose for beam target areas, dose calculations for radiation therapy as well as being adapted for use in the simulation of events in the ALICE detector at the LHC.

OpenSearch (ECHO-ESIP) & REST API for Earth Science Data Access

NASA Astrophysics Data System (ADS)

Mitchell, A.; Cechini, M.; Pilone, D.

2010-12-01

This presentation will provide a brief technical overview of OpenSearch, the Earth Science Information Partners (ESIP) Federated Search framework, and the REST architecture; discuss NASA’s Earth Observing System (EOS) ClearingHOuse’s (ECHO) implementation lessons learned; and demonstrate the simplified usage of these technologies. SOAP, as a framework for web service communication has numerous advantages for Enterprise applications and Java/C# type programming languages. As a technical solution, SOAP has been a reliable framework on top of which many applications have been successfully developed and deployed. However, as interest grows for quick development cycles and more intriguing “mashups,” the SOAP API loses its appeal. Lightweight and simple are the vogue characteristics that are sought after. Enter the REST API architecture and OpenSearch format. Both of these items provide a new path for application development addressing some of the issues unresolved by SOAP. ECHO has made available all of its discovery, order submission, and data management services through a publicly accessible SOAP API. This interface is utilized by a variety of ECHO client and data partners to provide valuable capabilities to end users. As ECHO interacted with current and potential partners looking to develop Earth Science tools utilizing ECHO, it became apparent that the development overhead required to interact with the SOAP API was a growing barrier to entry. ECHO acknowledged the technical issues that were being uncovered by its partner community and chose to provide two new interfaces for interacting with the ECHO metadata catalog. The first interface is built upon the OpenSearch format and ESIP Federated Search framework. Leveraging these two items, a client (ECHO-ESIP) was developed with a focus on simplified searching and results presentation. The second interface is built upon the Representational State Transfer (REST) architecture. Leveraging the REST architecture, a new API has been made available that will provide access to the entire SOAP API suite of services. The results of these development activities has not only positioned to engage in the thriving world of mashup applications, but also provided an excellent real-world case study of how to successfully leverage these emerging technologies.

Re-Framing the World Wide Web

ERIC Educational Resources Information Center

Black, August

2011-01-01

The research presented in this dissertation studies and describes how technical standards, protocols, and application programming interfaces (APIs) shape the aesthetic, functional, and affective nature of our most dominant mode of online communication, the World Wide Web (WWW). I examine the politically charged and contentious battle over browser…

Man-systems distributed system for Space Station Freedom

NASA Technical Reports Server (NTRS)

Lewis, J. L.

1990-01-01

Viewgraphs on man-systems distributed system for Space Station Freedom are presented. Topics addressed include: description of man-systems (definition, requirements, scope, subsystems, and topologies); implementation (approach, tools); man-systems interfaces (system to element and system to system); prime/supporting development relationship; selected accomplishments; and technical challenges.

Study of Composite Interface Strength and Crack Growth Monitoring Using Carbon Nanotubes

DTIC Science & Technology

2009-09-01

Carbon Nanotube Additives,” Applied Physiscs Letters, 91(2007). 14Tsu-Wei Chou and Erik T. Thosetenson. “Carbon Nanotube/Vinyl Ester Nanocomposites...Carbon Nanotube Additives. Applied Physiscs Letters 91. 79 INITIAL DISTRIBUTION LIST 1. Defense Technical Information Center Ft. Belvoir, Virginia

Downloading from the OPAC: The Innovative Interfaces Environment.

ERIC Educational Resources Information Center

Spore, Stuart

1991-01-01

Discussion of downloading from online public access catalogs focuses on downloading to MS-DOS microcomputers from the INNOPAC online catalog system. Tools for capturing and postprocessing downloaded files are described, technical and institutional constraints on downloading are addressed, and an innovative program for overcoming such constraints…

29. SITE BUILDING 002 SCANNER BUILDING FLOOR 3A ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. SITE BUILDING 002 - SCANNER BUILDING - FLOOR 3A ("A" FACE) AT SYSTEM LAYOUT GRID 17. GENERAL OBLIQUE VIEW OF "A" FACE INTERIOR SHOWING RADAR EMITTER/ANTENNA INTERFACE ELECTRONICS. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Ernst, W.; Richey, A.; Farrell, R.; Riecke, G.; Smith, G.; Howarth, R.; Cronin, M.; Simetkosky, M.; Meacher, J.

1986-01-01

This is the ninth Semiannual Technical Progress Report prepared under the Automotive Stirling Engine Development Program. It covers the twenty-eighth and twenty-ninth quarters of activity after award of the contract. Quarterly Technical Progress Reports related program activities from the first through the thirteenth quarters; thereafter, reporting was changed to a Semiannual format. This report summarizes the study of higher-power kinematic Stirling engines for transportation use, development testing of Mod I Stirling engines, and component development activities. Component development testing included successful conical fuel nozzle testing and functional checkout of Mod II controls and auxiliaries on Mod I engine test beds. Overall program philosophy is outlined and data and test results are presented.

Publications of the Jet Propulsion Laboratory, 1981

NASA Technical Reports Server (NTRS)

1982-01-01

Over 500 externally distributed technical reports released during 1981 that resulted from scientific and engineering work performed, or managed by Jet Propulsion Laboratory are listed by primary author. Of the total number of entries, 311 are from the bimonthly Deep Space Network Progress Report, and its successor, the Telecommunications and Data Acquisition Progress Report.

40 CFR 35.4170 - What kinds of reporting does EPA require?

Code of Federal Regulations, 2011 CFR

2011-07-01

... OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Technical Assistance Managing Your Tag... period which ends June 30 and December 31 of each year. (b) [Reserved] (c) Progress Report Full description in chart or narrative format of the progress your group made in relation to your approved schedule...

77 FR 75441 - Healthy Home and Lead Hazard Control Grant Programs Data Collection; Progress Reporting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-20

... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT [Docket No. FR-5603-N-93] Healthy Home and Lead Hazard... collection is designed to provide HUD timely information on progress of Healthy Homes Demonstration Program, Healthy Homes Technical Studies Program, Lead Base paint Hazard Control program, Lead Hazard Reduction...

Measuring Student Progress in the Classroom: A Guide to Testing and Evaluating Progress of Students with Disabilities.

ERIC Educational Resources Information Center

Hartman, Rhona C.; Redden, Martha Ross

This fact sheet provides guidelines on adapting testing situations for disabled postsecondary students. Discussed in the first section are considerations in determining when testing adaptations are needed including disability verification procedures, policy consistency, and maintenance of academic and technical standards. Facts about disabilities…

Progress in the First Five Years: An Evaluation of Achieving the Dream Colleges in Washington State

ERIC Educational Resources Information Center

Jenkins, Davis; Wachen, John; Kerrigan, Monica Reid; Mayer, Alexander K.

2012-01-01

In 2006, six community and technical colleges in Washington State joined the innovative national reform initiative called Achieving the Dream (ATD). This report describes the progress each college made in implementing ATD's "culture of evidence" principles for institutional improvement, examines strategies implemented by the colleges to…

Effect of pulsed progressive fluoroscopy on reduction of radiation dose in the cardiac catheterization laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holmes, D.R. Jr.; Wondrow, M.A.; Gray, J.E.

1990-01-01

The increased application of therapeutic interventional cardiology procedures is associated with increased radiation exposure to physicians, patients and technical personnel. New advances in imaging techniques have the potential for reducing radiation exposure. A progressive scanning video system with a standard vascular phantom has been shown to decrease entrance radiation exposure. The effect of this system on reducing actual radiation exposure to physicians and technicians was assessed from 1984 through 1987. During this time, progressive fluoroscopy was added sequentially to all four adult catheterization laboratories; no changes in shielding procedures were made. During this time, the case load per physician increasedmore » by 63% and the number of percutaneous transluminal coronary angioplasty procedures (a high radiation procedure) increased by 244%. Despite these increases in both case load and higher radiation procedures, the average radiation exposure per physician declined by 37%. During the same time, the radiation exposure for technicians decreased by 35%. Pulsed progressive fluoroscopy is effective for reducing radiation exposure to catheterization laboratory physicians and technical staff.« less

A Function-Behavior-State Approach to Designing Human Machine Interface for Nuclear Power Plant Operators

NASA Astrophysics Data System (ADS)

Lin, Y.; Zhang, W. J.

2005-02-01

This paper presents an approach to human-machine interface design for control room operators of nuclear power plants. The first step in designing an interface for a particular application is to determine information content that needs to be displayed. The design methodology for this step is called the interface design framework (called framework ). Several frameworks have been proposed for applications at varying levels, including process plants. However, none is based on the design and manufacture of a plant system for which the interface is designed. This paper presents an interface design framework which originates from design theory and methodology for general technical systems. Specifically, the framework is based on a set of core concepts of a function-behavior-state model originally proposed by the artificial intelligence research community and widely applied in the design research community. Benefits of this new framework include the provision of a model-based fault diagnosis facility, and the seamless integration of the design (manufacture, maintenance) of plants and the design of human-machine interfaces. The missing linkage between design and operation of a plant was one of the causes of the Three Mile Island nuclear reactor incident. A simulated plant system is presented to explain how to apply this framework in designing an interface. The resulting human-machine interface is discussed; specifically, several fault diagnosis examples are elaborated to demonstrate how this interface could support operators' fault diagnosis in an unanticipated situation.

Investigating buried polymer interfaces using sum frequency generation vibrational spectroscopy

PubMed Central

Chen, Zhan

2010-01-01

This paper reviews recent progress in the studies of buried polymer interfaces using sum frequency generation (SFG) vibrational spectroscopy. Both buried solid/liquid and solid/solid interfaces involving polymeric materials are discussed. SFG studies of polymer/water interfaces show that different polymers exhibit varied surface restructuring behavior in water, indicating the importance of probing polymer/water interfaces in situ. SFG has also been applied to the investigation of interfaces between polymers and other liquids. It has been found that molecular interactions at such polymer/liquid interfaces dictate interfacial polymer structures. The molecular structures of silane molecules, which are widely used as adhesion promoters, have been investigated using SFG at buried polymer/silane and polymer/polymer interfaces, providing molecular-level understanding of polymer adhesion promotion. The molecular structures of polymer/solid interfaces have been examined using SFG with several different experimental geometries. These results have provided molecular-level information about polymer friction, adhesion, interfacial chemical reactions, interfacial electronic properties, and the structure of layer-by-layer deposited polymers. Such research has demonstrated that SFG is a powerful tool to probe buried interfaces involving polymeric materials, which are difficult to study by conventional surface sensitive analytical techniques. PMID:21113334

CAGI: Computer Aided Grid Interface. A work in progress

NASA Technical Reports Server (NTRS)

Soni, Bharat K.; Yu, Tzu-Yi; Vaughn, David

1992-01-01

Progress realized in the development of a Computer Aided Grid Interface (CAGI) software system in integrating CAD/CAM geometric system output and/or Interactive Graphics Exchange Standard (IGES) files, geometry manipulations associated with grid generation, and robust grid generation methodologies is presented. CAGI is being developed in a modular fashion and will offer fast, efficient and economical response to geometry/grid preparation, allowing the ability to upgrade basic geometry in a step-by-step fashion interactively and under permanent visual control along with minimizing the differences between the actual hardware surface descriptions and corresponding numerical analog. The computer code GENIE is used as a basis. The Non-Uniform Rational B-Splines (NURBS) representation of sculptured surfaces is utilized for surface grid redistribution. The computer aided analysis system, PATRAN, is adapted as a CAD/CAM system. The progress realized in NURBS surface grid generation, the development of IGES transformer, and geometry adaption using PATRAN will be presented along with their applicability to grid generation associated with rocket propulsion applications.

A Tool for Measuring NASA's Aeronautics Research Progress Toward Planned Strategic Community Outcomes

NASA Technical Reports Server (NTRS)

Tahmasebi, Farhad; Pearce, Robert

2016-01-01

Description of a tool for portfolio analysis of NASA's Aeronautics research progress toward planned community strategic Outcomes is presented. For efficiency and speed, the tool takes advantage of a function developed in Excels Visual Basic for Applications. The strategic planning process for determining the community Outcomes is also briefly discussed. Stakeholder buy-in, partnership performance, progress of supporting Technical Challenges, and enablement forecast are used as the criteria for evaluating progress toward Outcomes. A few illustrative examples of using the tool are also presented.

Polymers and biopolymers at interfaces

NASA Astrophysics Data System (ADS)

Hall, A. R.; Geoghegan, M.

2018-03-01

This review updates recent progress in the understanding of the behaviour of polymers at surfaces and interfaces, highlighting examples in the areas of wetting, dewetting, crystallization, and ‘smart’ materials. Recent developments in analysis tools have yielded a large increase in the study of biological systems, and some of these will also be discussed, focussing on areas where surfaces are important. These areas include molecular binding events and protein adsorption as well as the mapping of the surfaces of cells. Important techniques commonly used for the analysis of surfaces and interfaces are discussed separately to aid the understanding of their application.

Career and Technical Education and Academic Progress at the End of High School: Evidence from the Education Longitudinal Study of 2002

ERIC Educational Resources Information Center

Bozick, Robert; Dalton, Ben

2013-01-01

This report examines the role of career and technical education (CTE) for assessing students in learning mathematics and preventing students from dropping out of high school. CTE is a wide field of educational practice that includes occupational training and career preparation offered in formats ranging from individual courses to comprehensive…

easyCBM[R] Mathematics Criterion Related Validity Evidence: Oregon State Test. Technical Report #1011

ERIC Educational Resources Information Center

Anderson, Daniel; Alonzo, Julie; Tindal, Gerald

2010-01-01

In this technical report, we present the results of a study examining the relation between the math measures available on the easyCBM[R] online benchmark and progress monitoring assessment system and the Oregon statewide assessment of mathematics. Designed for use within a response to intervention (RTI) framework, easyCBM[R] is intended to help…

New York City School Survey 2008-2010: Assessing the Reliability and Validity of a Progress Report Measure. Technical Appendices

ERIC Educational Resources Information Center

Nathanson, Lori; Cole, Rachel; Kemple, James J.; Lent, Jessica; McCormick, Meghan; Segeritz, Micha

2013-01-01

The Research Alliance for New York City Schools examined Department of Education (DOE) School Survey data from 2008-2010 to better understand the richness and complexities of the information elicited by the Survey from parents, students, and teachers. This document provides the appendices to the technical report "New York City School Survey…

The 1992 Research/Technology report

NASA Technical Reports Server (NTRS)

1992-01-01

The 1992 Research & Technology report is organized so that a broad cross section of the community can readily use it. A short introductory paragraph begins each article and will prove to be an invaluable reference tool for the layperson. The approximately 200 articles summarize the progress made during the year in various technical areas and portray the technical and administrative support associated with Lewis technology programs.

Trends in Articulation Arrangements for Technical and Vocational Education in the South East Asian Region.

ERIC Educational Resources Information Center

Haas, Adrian R.

Trends in articulation arrangements for technical and vocational education (TVE) in the South East Asia region were studied. A key feature of articulation is the existence of pathways that allow graduates of one course of study to progress to other courses. Effective articulation opens up advancement for individuals and helps to create a flexible…

Longitudinal Surveys of Australian Youth (LSAY) 1998 Cohort: Wave 12 (2009)--Frequency Tables. Technical Report 58B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 1998 cohort Wave 12 (2009) data set. [For the accompanying questionnaire, "Longitudinal Surveys…

Longitudinal Surveys of Australian Youth (LSAY): 2003 Cohort Wave 7 (2009)--Frequency Tables. Technical Report 57B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 2003 cohort Wave 7 (2009) data set. [For the related questionnaire, see ED512164.

Longitudinal Surveys of Australian Youth (LSAY) 2009 Cohort: Wave 3 (2011)--Frequency Tables. Technical Report 72B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2012

2012-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 2009 cohort Wave 3 (2011) data set. [For the related questionnaire, see ED536306.

Longitudinal Surveys of Australian Youth (LSAY) 2003 Cohort: Wave 7 (2009)--Questionnaire. Technical Report 57A

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the questionnaire for the LSAY 2003 cohort Wave 7 (2009) data set. [For the related frequency tables, see ED512163.

Making the Good Even Better: Feedback from easyCBM Focus Groups, School Year 2009/2010. Technical Report # 1001

ERIC Educational Resources Information Center

Alonzo, Julie; Tindal, Gerald; Lai, Cheng-Fei

2010-01-01

This technical report provides a summary of feedback from teachers, administrators, and support personnel who used the easyCBM progress monitoring and benchmark assessment system during school year 2009/2010. Data were gathered from semi-structured focus groups conducted during the 2010 easyCBM August Institute at the University of Oregon. Results…

Longitudinal Surveys of Australian Youth (LSAY): 2006 Cohort Wave 4 (2009)--Frequency Tables. Technical Report 56B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 2006 cohort Wave 4 (2009) data set. [For the "Longitudinal Surveys of Australian Youth (LSAY):…

Longitudinal Surveys of Australian Youth (LSAY): 2006 Cohort Wave 4 (2009)--Questionnaire. Technical Report 56A

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the questionnaire for the LSAY 2006 cohort Wave 4 (2009) data set. [For the "Longitudinal Surveys of Australian Youth (LSAY):…

Establishment of the Center for Advanced Separation Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christopher E. Hull

2006-09-30

This Final Technical Report covers the eight sub-projects awarded in the first year and the five projects awarded in the second year of Cooperative Agreement DE-FC26-01NT41091: Establishment of the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

A Historical Introduction to Library Education: Problems and Progress to 1951.

ERIC Educational Resources Information Center

White, Carl M.

The growth of libraries and of technical education in the middle of the 19th century led to the organization of Melvil Dewey's School of Library Economy in 1887. The School offered a technical course to replace the apprenticeships then in favor. Its curriculum persisted as the model for library education through 1920. A break with the early form…

Progress Report on Reactivity Analyses (October-December Test Data). Beginning Teacher Evaluation Study. Technical Note Series. Technical Note III-5.

ERIC Educational Resources Information Center

Filby, Nikola N.

The development and refinement of the measures of student achievement in reading and mathematics for the Beginning Teacher Evaluation Study are described. The concept of reactivity to instruction is introduced: the tests used to evaluate instructional processes must be sensitive indicators of classroom learning overtime. Data collection activities…

First results of ground-based LWIR hyperspectral imaging remote gas detection

NASA Astrophysics Data System (ADS)

Zheng, Wei-jian; Lei, Zheng-gang; Yu, Chun-chao; Wang, Hai-yang; Fu, Yan-peng; Liao, Ning-fang; Su, Jun-hong

2014-11-01

The new progress of ground-based long-wave infrared remote sensing is presented. The LWIR hyperspectral imaging by using the windowing spatial and temporal modulation Fourier spectroscopy, and the results of outdoor ether gas detection, verify the features of LWIR hyperspectral imaging remote sensing and technical approach. It provides a new technical means for ground-based gas remote sensing.

Review of Web-Based Technical Documentation Processes. FY07 NAEP-QA Special Study Report. TR-08-17

ERIC Educational Resources Information Center

Gribben, Monica; Wise, Lauress; Becker, D. E.

2008-01-01

Beginning with the 2000 and 2001 National Assessment of Educational Progress (NAEP) assessments, the National Center for Education Statistics (NCES) has made technical documentation available on the worldwide web at http://nces.ed.gov/nationsreportcard/tdw/. The web-based documentation is designed to be less dense and more accessible than prior…

Oil-Water Interface Templating of Mesoporous Macroscale Structures

PubMed

Schacht; Huo; Voigt-Martin; Stucky; Schuth

1996-08-09

Ordered mesostructured porous silicas that are also macroscopically structured were created by control of the interface on two different length scales simultaneously. Micellar arrays controlled the nanometer-scale assembly, and at the static boundary between an aqueous phase and an organic phase, control was achieved on the micrometer to centimeter scale. Acid-prepared mesostructures of silica were made with the p6, Pm3n, and the P63/mmc structures in the form of porous fibers 50 to 1000 micrometers in length, hollow spheres with diameters of 1 to 100 micrometers, and thin sheets up to 10 centimeters in diameter and about 10 to 500 micrometers in thickness. These results might have implications for technical applications, such as slow drug-release systems or membranes, and in biomineralization, where many processes are also interface-controlled.

Transfer of control system interface solutions from other domains to the thermal power industry.

PubMed

Bligård, L-O; Andersson, J; Osvalder, A-L

2012-01-01

In a thermal power plant the operators' roles are to control and monitor the process to achieve efficient and safe production. To achieve this, the human-machine interfaces have a central part. The interfaces need to be updated and upgraded together with the technical functionality to maintain optimal operation. One way of achieving relevant updates is to study other domains and see how they have solved similar issues in their design solutions. The purpose of this paper is to present how interface design solution ideas can be transferred from domains with operator control to thermal power plants. In the study 15 domains were compared using a model for categorisation of human-machine systems. The result from the domain comparison showed that nuclear power, refinery and ship engine control were most similar to thermal power control. From the findings a basic interface structure and three specific display solutions were proposed for thermal power control: process parameter overview, plant overview, and feed water view. The systematic comparison of the properties of a human-machine system allowed interface designers to find suitable objects, structures and navigation logics in a range of domains that could be transferred to the thermal power domain.

Crew interface specifications development functions, phase 3A

NASA Technical Reports Server (NTRS)

Carl, J. G.

1973-01-01

The findings and data products developed during the crew interface specification study for inflight maintenance and stowage functions are presented. Guidelines are provided for improving the present progress of defining, controlling, and managing the flight crew requirements. The following data products were developed: (1) description of inflight maintenance management process, (2) specifications for inflight maintenance management requirements, and (3) suggested inflight maintenance data processing reports for logistics management.

The virtual windtunnel: Visualizing modern CFD datasets with a virtual environment

NASA Technical Reports Server (NTRS)

Bryson, Steve

1993-01-01

This paper describes work in progress on a virtual environment designed for the visualization of pre-computed fluid flows. The overall problems involved in the visualization of fluid flow are summarized, including computational, data management, and interface issues. Requirements for a flow visualization are summarized. Many aspects of the implementation of the virtual windtunnel were uniquely determined by these requirements. The user interface is described in detail.

A Comparison of Two Control Display Unit Concepts on Flight Management System Training

NASA Technical Reports Server (NTRS)

Abbott, Terence S.

1997-01-01

One of the biggest challenges for a pilot in the transition to a 'glass' cockpit is understanding the flight management system (FMS). Because of both the complex nature of the FMS and the pilot-FMS interface, a large portion of transition training is devoted to the FMS. The current study examined the impact of the primary pilot-FMS interface, the control display unit (CDU), on FMS training. Based on the hypothesis that the interface design could have a significant impact on training, an FMS simulation with two separate interfaces was developed. One interface was similar to a current-generation design, and the other was a multiwindows CDU based on graphical user interface techniques. For both application and evaluation reasons, constraints were applied to the graphical CDU design to maintain as much similarity as possible with the conventional CDU. This preliminary experiment was conducted to evaluate the interface effects on training. Sixteen pilots with no FMS experience were used in a between-subjects test. A time-compressed, airline-type FMS training environment was simulated. The subjects were trained to a fixed-time criterion, and performance was measured in a final, full-mission simulation context. This paper describes the technical approach, simulation implementation, and experimental results of this effort.

Polymer-grafted Lignin: Molecular Design and Interfacial Activities

NASA Astrophysics Data System (ADS)

Gupta, Chetali

The broader technical objective of this work is to develop a strategy for using the biopolymer lignin in a wide variety of surfactant applications through polymer grafting. These applications include emulsion stabilizers, dispersants and foaming agents. The scientific objective of the research performed within this thesis is to understand the effect of molecular architecture and polymer grafting on the interfacial activity at the air-liquid, liquid-liquid and solid-liquid interface. Research has focused on designing of these lignopolymers with controlled architecture using polyethylene glycol, poly(acrylic acid) and polyacrylamide grafts. The interfacial activity for all polymer grafts has been tested at all three interfaces using a broad range of techniques specific to the interface. Results have shown that the hydrophobicity of the lignin core is responsible for enhanced interfacial activity at the air-liquid and liquid-liquid interface. Conversely, improved hydrophilicity and "electrosteric" interactions are required for higher interfacial activity of the lignin at the liquid-solid interface. The high interfacial activity of the polymer-grafted lignin observed in the air-liquid and liquid-liquid interfaces not only resulted in viscosity reduction but also strength enhancement at the liquid-solid interface. The broader implication of this study is to be able to predict what chemical functionalities need to be adjusted to get the desired viscosity reduction.

The origin of high PCE in PTB7 based photovoltaics: proper charge neutrality level and free energy of charge separation at PTB7/PC71BM interface

PubMed Central

Park, Soohyung; Jeong, Junkyeong; Hyun, Gyeongho; Kim, Minju; Lee, Hyunbok; Yi, Yeonjin

2016-01-01

The energy level alignments at donor/acceptor interfaces in organic photovoltaics (OPVs) play a decisive role in device performance. However, little is known about the interfacial energetics in polymer OPVs due to technical issues of the solution process. Here, the frontier ortbial line-ups at the donor/acceptor interface in high performance polymer OPVs, PTB7/PC71BM, were investigated using in situ UPS, XPS and IPES. The evolution of energy levels during PTB7/PC71BM interface formation was investigated using vacuum electrospray deposition, and was compared with that of P3HT/PC61BM. At the PTB7/PC71BM interface, the interface dipole and the band bending were absent due to their identical charge neutrality levels. In contrast, a large interfacial dipole was observed at the P3HT/PC61BM interface. The measured photovoltaic energy gap (EPVG) was 1.10 eV for PTB7/PC71BM and 0.90 eV for P3HT/PC61BM. This difference in the EPVG leads to a larger open-circuit voltage of PTB7/PC71BM than that of P3HT/PC61BM. PMID:27734957

The origin of high PCE in PTB7 based photovoltaics: proper charge neutrality level and free energy of charge separation at PTB7/PC71BM interface.

PubMed

Park, Soohyung; Jeong, Junkyeong; Hyun, Gyeongho; Kim, Minju; Lee, Hyunbok; Yi, Yeonjin

2016-10-13

The energy level alignments at donor/acceptor interfaces in organic photovoltaics (OPVs) play a decisive role in device performance. However, little is known about the interfacial energetics in polymer OPVs due to technical issues of the solution process. Here, the frontier ortbial line-ups at the donor/acceptor interface in high performance polymer OPVs, PTB7/PC 71 BM, were investigated using in situ UPS, XPS and IPES. The evolution of energy levels during PTB7/PC 71 BM interface formation was investigated using vacuum electrospray deposition, and was compared with that of P3HT/PC 61 BM. At the PTB7/PC 71 BM interface, the interface dipole and the band bending were absent due to their identical charge neutrality levels. In contrast, a large interfacial dipole was observed at the P3HT/PC 61 BM interface. The measured photovoltaic energy gap (E PVG ) was 1.10 eV for PTB7/PC 71 BM and 0.90 eV for P3HT/PC 61 BM. This difference in the E PVG leads to a larger open-circuit voltage of PTB7/PC 71 BM than that of P3HT/PC 61 BM.

Role of the interface between distributed fibre optic strain sensor and soil in ground deformation measurement

NASA Astrophysics Data System (ADS)

Zhang, Cheng-Cheng; Zhu, Hong-Hu; Shi, Bin

2016-11-01

Recently the distributed fibre optic strain sensing (DFOSS) technique has been applied to monitor deformations of various earth structures. However, the reliability of soil deformation measurements remains unclear. Here we present an integrated DFOSS- and photogrammetry-based test study on the deformation behaviour of a soil foundation model to highlight the role of strain sensing fibre-soil interface in DFOSS-based geotechnical monitoring. Then we investigate how the fibre-soil interfacial behaviour is influenced by environmental changes, and how the strain distribution along the fibre evolves during progressive interface failure. We observe that the fibre-soil interfacial bond is tightened and the measurement range of the fibre is extended under high densities or low water contents of soil. The plastic zone gradually occupies the whole fibre length when the soil deformation accumulates. Consequently, we derive a theoretical model to simulate the fibre-soil interfacial behaviour throughout the progressive failure process, which accords well with the experimental results. On this basis, we further propose that the reliability of measured strain can be determined by estimating the stress state of the fibre-soil interface. These findings may have important implications for interpreting and evaluating fibre optic strain measurements, and implementing reliable DFOSS-based geotechnical instrumentation.

UAS Integration in the NAS Project: Part Task 6 V & V Simulation: Primary Results

NASA Technical Reports Server (NTRS)

Rorie, Conrad; Fern, Lisa; Shively, Jay; Santiago, Confesor

2016-01-01

This is a presentation of the preliminary results on final V and V (Verification and Validation) activity of [RTCA (Radio Technical Commission for Aeronautics)] SC (Special Committee)-228 DAA (Detect and Avoid) HMI (Human-Machine Interface) requirements for display alerting and guidance.

Reflections of an Artist-Engineer on the Art-Science Interface

ERIC Educational Resources Information Center

Malina, Frank J.

1974-01-01

In a world increasingly concerned about the social results of scientific discovery and technical change, we tend to lose sight of the artist as inventor and human being. Creative talent needs opportunity lest it continue to be almost as rare as the genius of the great scientist. (Editor/JR)

Common Ada Programming Support Environment (APSE) Interface Set (CAIS) Implementation Validation Capability (CIVC2)

DTIC Science & Technology

1992-06-01

Paper, Version 2.0, December 1989. [Woodcock90] Gary Woodcock , Automated Generation of Hypertext Documents, CIVC Technical Report (working paper...environment setup, performance testing, assessor testing, and analysis) of the ACEC. A captive scenario example could be developed that would guide the

The Arabization of a Full-Text Database Interface.

ERIC Educational Resources Information Center

Fayen, Emily Gallup; And Others

The 1981 design specifications for the Egyptian National Scientific and Technical Information Network (ENSTINET) stipulated that major end-user facilities of the system should be bilingual in English and Arabic. Many characteristics of the Arabic alphabet and language impact computer applications, and there exists no universally accepted character…

Exploring the Science--Society Interface with a Bridging Research Course

ERIC Educational Resources Information Center

Boltax, Ariana L.; Kosinski-Collins, Melissa S.; Pontrello, Jason K.

2016-01-01

This article describes the development of a model for an optional, research-based course that bridges two existing, traditionally separate, introductory science courses. This research course provided freedom for students to design and implement new experiments on the basis of technical foundations built from enrollment in separate introductory…

Diffuse Interface Methods for Multiclass Segmentation of High-Dimensional Data

DTIC Science & Technology

2014-03-04

handwritten digits , 1998. http://yann.lecun.com/exdb/mnist/. [19] S. Nene, S. Nayar, H. Murase, Columbia Object Image Library (COIL-100), Technical Report... recognition on smartphones using a multiclass hardware-friendly support vector machine, in: Ambient Assisted Living and Home Care, Springer, 2012, pp. 216–223.