Long-Range Interactions Restrict Water Transport in Pyrophyllite Interlayers

PubMed Central

Zarzycki, Piotr; Gilbert, Benjamin

2016-01-01

Water diffusion within smectite clay interlayers is reduced by confinement and hence is highly determined by the interlayer spacings that are adopted during swelling. However, a molecular understanding of the short- and long-range forces governing interlayer water structure and dynamics is lacking. Using molecular dynamics simulations of water intercalated between pyrophyllite (smectite prototype) layers we provide a detailed picture of the variation of interlayered water mobility accompanying smectite expansion. Subtle changes in hydrogen bond network structure cause significant changes in water mobility that is greater for stable hydration states and reduced for intermediate separations. By studying pyrophyllite with and without external water we reveal that long-range electrostatic forces apply a restraining effect upon interlayer water mobility. Our findings are relevant for broad range of confining nanostructures with walls thin enough to permit long-range interactions that could affect the mobility of confined solvent molecules and solute species. PMID:27118164

Hydration thermodynamics of the SWy-1 montmorillonite saturated with alkali and alkaline-earth cations: A predictive model

NASA Astrophysics Data System (ADS)

Vieillard, Philippe; Blanc, Philippe; Fialips, Claire I.; Gailhanou, Hélène; Gaboreau, Stéphane

2011-10-01

The aim of the present work was to study the thermodynamic equilibria between water and a homo-ionic montmorillonite SWy-1 saturated by different cations. The choice of this smectite is justified by the large set of experimental data available from the literature for eight different interlayer cations: Na +, K +, Rb +, Cs +, Mg 2+, Ca 2+, Sr 2+, and Ba 2+. In particular, studies by Cases et al. (1992, 1997) and Bérend et al. (1995) are providing heat of adsorption data, pairs of desorption-adsorption isotherms, and information about the partition of adsorption-desorption water molecules between external surfaces and internal spaces. By calculating the effective amount of hydration water as the difference between the so-called gravimetric water and the surface covering water, a thermodynamic model was then developed, based on the concept of Ransom and Helgeson (1994) considering an asymmetric subregular binary solid solution between a fully hydrated and a anhydrous smectite. A set of six thermodynamic parameters ( ΔH∘hyd,S∘hyd and four Margules parameters) was extracted by a least square method from measurements of enthalpies of adsorption and paired adsorption-desorption isotherms for each interlayer cation. These six initial parameters were then used to determine a complete set of standard thermodynamic hydration parameters ( ΔH∘hyd,ΔG∘hyd,ΔS∘hyd, heat capacity, molar volume, and number of interlayer H 2O) and quantify, for each cation, the number of moles of hydration water molecules as a function of relative humidity and temperature. The validation of the standard state thermodynamic properties of hydration for each end member was carried out using three approaches: (1) a comparison with experimental isotherms obtained on hetero-ionic and homo-ionic SWy-1 smectite at different temperatures; (2) a comparison with the experimental integral enthalpy and entropy of hydration of the SWy-1 smectite; and (3) a comparison with experimental isotherms acquired on various smectites (Upton, MX80, Arizona) with different layer charges. Eventually, the present work demonstrates that, from a limited number of measurements, it is possible to provide the hydration thermodynamic parameters for hydrated smectites with different compositions and under different conditions of temperature and relative humidity, using the newly developed predictive model.

Sugar-influenced water diffusion, interaction, and retention in clay interlayer nanopores probed by theoretical simulations and experimental spectroscopies

NASA Astrophysics Data System (ADS)

Aristilde, Ludmilla; Galdi, Stephen M.; Kelch, Sabrina E.; Aoki, Thalia G.

2017-08-01

Understanding the hydrodynamics in clay nanopores is important for gaining insights into the trapping of water, nutrients, and contaminants in natural and engineered soils. Previous investigations have focused on the interlayer organization and molecular diffusion coefficients (D) of cations and water molecules in cation-saturated interlayer nanopores of smectite clays. Little is known, however, about how these interlayer dynamic properties are influenced by the ubiquitous presence of small organic compounds such as sugars in the soil environment. Here we probed the effects of glucose molecules on montmorillonite interlayer properties. Molecular dynamics simulations revealed re-structuring of the interlayer organization of the adsorptive species. Water-water interactions were disrupted by glucose-water H-bonding interactions. ;Dehydration; of the glucose-populated nanopore led to depletion in the Na solvation shell, which resulted in the accumulation of both Na ions (as inner-sphere complexes) and remaining hydrated water molecules at the mineral surface. This accumulation led to a decrease in both DNa and Dwater. In addition, the reduction in Dglucose as a function of increasing glucose content can be explained by the aggregation of glucose molecules into organic clusters H-bonded to the mineral surface on both walls of the nanopore. Experimental nuclear magnetic resonance and X-ray diffraction data were consistent with the theoretical predictions. Compared to clay interlayers devoid of glucose, increased intensities and new peaks in the 23Na nuclear magnetic resonance spectra confirmed increasing immobilization of Na as a function of increasing glucose content. And, the X-ray diffraction data indicated a reduced collapse of glucose-populated interlayers exposed to decreasing moisture conditions, which led to the maintenance of hydrated clay nanopores. The coupling of theoretical and experimental findings sheds light on the molecular to nanoscale mechanisms that control the enhanced trapping of water molecules and solutes within sugar-enriched clay nanopores.

ROLE OF PRESSURE IN SMECTITE DEHYDRATION - EFFECTS ON GEOPRESSURE AND SMECTITE-TO-ILLITE TRANSFORMATION.

USGS Publications Warehouse

Colten-Bradley, Virginia

1987-01-01

Evaluation of the effects of pressure on the temperature of interlayer water loss (dehydration) by smectites under diagenetic conditions indicates that smectites are stable as hydrated phases in the deep subsurface. Hydraulic and differential pressure conditions affect dehydration differently. The temperature of dehydration increase with pore fluid pressure and interlayer water density. The temperatures of dehydration increase with pore fluid pressure and interlayer water density. The temperatures of dehydration under differential-presssure conditions are inversely related to pressure and interlayer water density. The model presented assumes the effects of pore fluid composition and 2:1 layer reactivity to be negligible. Agreement between theoretical and experimental results validate this assumption. Additional aspects of the subject are discussed.

Molecular dynamics simulations reveal that water diffusion between graphene oxide layers is slow

DOE PAGES

Devanathan, Ram; Chase-Woods, Dylan; Shin, Yongsoon; ...

2016-07-08

Membranes made of stacked layers of graphene oxide (GO) hold the tantalizing promise of revolutionizing desalination and water filtration if selective transport of molecules can be controlled. We present the findings of a molecular dynamics simulation study of water intercalated between GO layers that have a C/O ratio of 4. We simulated a range of hydration levels from 1 wt.% to 23.3 wt.% water. The interlayer spacing increased upon hydration from 0.8 nm to 1.1 nm. We also synthesized GO membranes that showed an increase in spacing from about 0.7 nm to 0.8 nm and an increase in mass ofmore » about 14% on hydration. Water diffusion through GO layers is an order of magnitude slower than that in bulk water, because of strong hydrogen bonded interactions. Most of the water molecules are bound to OH groups even at the highest hydration level. We observed large water clusters that could span graphitic regions, oxidized regions and holes that have been experimentally observed in GO. As a result, slow interlayer diffusion can be consistent with experimentally observed water transport in GO if holes lead to a shorter path length than previously assumed and sorption serves as a key rate-limiting step.« less

Molecular dynamics simulation of diffusion and electrical conductivity in montmorillonite interlayers

DOE PAGES

Greathouse, Jeffery A.; Cygan, Randall T.; Fredrich, Joanne T.; ...

2016-01-20

In this study, the diffusion of water and ions in the interlayer region of smectite clay minerals represents a direct probe of the type and strength of clay–fluid interactions. Interlayer diffusion also represents an important link between molecular simulation and macroscopic experiments. Here we use molecular dynamics simulation to investigate trends in cation and water diffusion in montmorillonite interlayers, looking specifically at the effects of layer charge, interlayer cation and cation charge (sodium or calcium), water content, and temperature. For Na-montmorillonite, the largest increase in ion and water diffusion coefficients occurs between the one-layer and two-layer hydrates, corresponding to themore » transition from inner-sphere to outer-sphere surface complexes. Calculated activation energies for ion and water diffusion in Na-montmorillonite are similar to each other and to the water hydrogen bond energy, suggesting the breaking of water–water and water–clay hydrogen bonds as a likely mechanism for interlayer diffusion. A comparison of interlayer diffusion with that of bulk electrolyte solutions reveals a clear trend of decreasing diffusion coefficient with increasing electrolyte concentration, and in most cases the interlayer diffusion results are nearly coincident with the corresponding bulk solutions. Trends in electrical conductivities computed from the ion diffusion coefficients are also compared.« less

Dynamics of confined reactive water in smectite clay-zeolite composites.

PubMed

Pitman, Michael C; van Duin, Adri C T

2012-02-15

The dynamics of water confined to mesoporous regions in minerals such as swelling clays and zeolites is fundamental to a wide range of resource management issues impacting many processes on a global scale, including radioactive waste containment, desalination, and enhanced oil recovery. Large-scale atomic models of freely diffusing multilayer smectite particles at low hydration confined in a silicalite cage are used to investigate water dynamics in the composite environment with the ReaxFF reactive force field over a temperature range of 300-647 K. The reactive capability of the force field enabled a range of relevant surface chemistry to emerge, including acid/base equilibria in the interlayer calcium hydrates and silanol formation on the edges of the clay and inner surface of the zeolite housing. After annealing, the resulting clay models exhibit both mono- and bilayer hydration structures. Clay surface hydration redistributed markedly and yielded to silicalite water loading. We find that the absolute rates and temperature dependence of water dynamics compare well to neutron scattering data and pulse field gradient measures from relevant samples of Ca-montmorillonite and silicalite, respectively. Within an atomistic, reactive context, our results distinguish water dynamics in the interlayer Ca(OH)(2)·nH(2)O environment from water flowing over the clay surface, and from water diffusing within silicalite. We find that the diffusion of water when complexed to Ca hydrates is considerably slower than freely diffusing water over the clay surface, and the reduced mobility is well described by a difference in the Arrhenius pre-exponential factor rather than a change in activation energy.

Synthesis and characterization of sodium vanadium oxide gels: the effects of water (n) and sodium (x) content on the electrochemistry of Na(x)V2O5·nH2O.

PubMed

Lee, Chia-Ying; Marschilok, Amy C; Subramanian, Aditya; Takeuchi, Kenneth J; Takeuchi, Esther S

2011-10-28

Sodium vanadium oxide gels, Na(x)V(2)O(5)·nH(2)O, of varying sodium content (0.12 < x < 0.32) were prepared by careful control of an ion exchange process. The water content (0.23 > n > 0.01) and interlayer spacing were found to be inversely proportional to the sodium level (x), thus control of sodium (x) content provided a direct, chimie douce approach for control of hydration level (n) and interlayer spacing, without the need for high temperature treatment to affect dehydration. Notably, the use of high temperatures to modify hydration levels can result in crystallization and collapse of the interlayer structure, highlighting the distinct advantage of our novel chimie douce synthesis strategy. Subsequent to synthesis and characterization, results from an electrochemical study of a series of Na(x)V(2)O(5)·nH(2)O samples highlight the significant impact of interlayer water on delivered capacity of the layered materials. Specifically, the sodium vanadium oxide gels with higher sodium content and lower water content provided higher capacities in lithium based cells, where capacity delivered to 2.0 V under C/20 discharge ranged from 170 mAh/g for Na(0.12)V(2)O(5)·0.23H(2)O to 300 mAh/g for Na(0.32)V(2)O(5)·0.01H(2)O. The capacity differences were maintained as the cells were cycled. This journal is © the Owner Societies 2011

Mineralogy of a mudstone at Yellowknife Bay, Gale crater, Mars.

PubMed

Vaniman, D T; Bish, D L; Ming, D W; Bristow, T F; Morris, R V; Blake, D F; Chipera, S J; Morrison, S M; Treiman, A H; Rampe, E B; Rice, M; Achilles, C N; Grotzinger, J P; McLennan, S M; Williams, J; Bell, J F; Newsom, H E; Downs, R T; Maurice, S; Sarrazin, P; Yen, A S; Morookian, J M; Farmer, J D; Stack, K; Milliken, R E; Ehlmann, B L; Sumner, D Y; Berger, G; Crisp, J A; Hurowitz, J A; Anderson, R; Des Marais, D J; Stolper, E M; Edgett, K S; Gupta, S; Spanovich, N

2014-01-24

Sedimentary rocks at Yellowknife Bay (Gale crater) on Mars include mudstone sampled by the Curiosity rover. The samples, John Klein and Cumberland, contain detrital basaltic minerals, calcium sulfates, iron oxide or hydroxides, iron sulfides, amorphous material, and trioctahedral smectites. The John Klein smectite has basal spacing of ~10 angstroms, indicating little interlayer hydration. The Cumberland smectite has basal spacing at both ~13.2 and ~10 angstroms. The larger spacing suggests a partially chloritized interlayer or interlayer magnesium or calcium facilitating H2O retention. Basaltic minerals in the mudstone are similar to those in nearby eolian deposits. However, the mudstone has far less Fe-forsterite, possibly lost with formation of smectite plus magnetite. Late Noachian/Early Hesperian or younger age indicates that clay mineral formation on Mars extended beyond Noachian time.

Characterizing the Phyllosilicate Component of the Sheepbed Mudstone in Gale Crater, Mars Using Laboratory XRD and EGA

NASA Technical Reports Server (NTRS)

Rampe, E. B.; Morris, R. V.; Ming, D. W.; Archer, P. D.; Bish, D. L.; Chipera, S. J.; Vaniman, D. T.; Blake, D. F.; Bristow, T. F.; Sutter, B.;

Calcium silicate hydrates: Solid and liquid phase composition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lothenbach, Barbara, E-mail: Barbara.lothenbach@empa.ch; Nonat, André

This paper presents a review on the relationship between the composition, the structure and the solution in which calcium silicate hydrate (C–S–H) is equilibrated. The silica chain length in C–S–H increases with the silicon concentration and the calcium content in the interlayer space with the calcium concentrations. Sodium and potassium are taken up in the interlayer space, preferentially at low calcium concentrations and thus by low Ca/Si C–S–H. Aluminium uptake in C–S–H increases strongly at higher aluminium concentrations in the solution. At low Ca/Si, aluminium substitutes silica in the bridging position, at Ca/Si > 1 aluminium is bound in TAH.more » Recently developed thermodynamic models are closely related to the structure of C–S–H and tobermorite, and able to model not only the solubility and the chemical composition of the C–S–H, but also to predict the mean silica chain length and the uptake of aluminium.« less

Cr6+-containing phases in the system CaO-Al2O3-CrO42--H2O at 23 °C

NASA Astrophysics Data System (ADS)

Pöllmann, Herbert; Auer, Stephan

2012-01-01

Synthesis and investigation of lamellar calcium aluminium hydroxy salts was performed to study the incorporation of chromate ions in the interlayer of lamellar calcium aluminium hydroxy salts. Different AFm-phases (calcium aluminate hydrate with alumina, ferric oxide, mono-anion phase) containing chromate were synthesized. These AFm-phases belong to the group of layered double hydroxides (LDHs). 3CaO·Al2O3·CaCrO4·nH2O and C3A·1/2Ca(OH)2·1/2CaCrO4·12H2O were obtained as pure phases and their different distinct interlayer water contents and properties determined. Solid solution of chromate-containing phases and tetracalcium-aluminate-hydrate (TCAH) were studied. The uptake of chromate into TCAH from solutions was proven. Chromate contents in solution decrease to <0.2 mg/l.

Hydration states of AFm cement phases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baquerizo, Luis G., E-mail: luis.baquerizoibarra@holcim.com; Matschei, Thomas; Scrivener, Karen L.

2015-07-15

The AFm phase, one of the main products formed during the hydration of Portland and calcium aluminate cement based systems, belongs to the layered double hydrate (LDH) family having positively charged layers and water plus charge-balancing anions in the interlayer. It is known that these phases present different hydration states (i.e. varying water content) depending on the relative humidity (RH), temperature and anion type, which might be linked to volume changes (swelling and shrinkage). Unfortunately the stability conditions of these phases are insufficiently reported. This paper presents novel experimental results on the different hydration states of the most important AFmmore » phases: monocarboaluminate, hemicarboaluminate, strätlingite, hydroxy-AFm and monosulfoaluminate, and the thermodynamic properties associated with changes in their water content during absorption/desorption. This data opens the possibility to model the response of cementitious systems during drying and wetting and to engineer systems more resistant to harsh external conditions.« less

Molecular Modeling of the Binding Structures in the Interlayer Adsorption of a Tetracycline Antibiotic by Smectite Clays

NASA Astrophysics Data System (ADS)

Aristilde, L.

2009-12-01

A controlling factor in the fate of antibiotics in the environment is their sequestration in soil particles including clay minerals. Of special interest is the interlayer adsorption by smectite clays, which has been shown to influence both the bioavailability and persistence of antibiotics in the soil environment. However, the interlayer structures of the bound antibiotics, essential to an accurate understanding of the adsorption mechanisms, are not well understood. Molecular simulations of oxytetracycline (OTC) with a model montmorillonite (MONT) clay were performed to gain insights into these structures for tetracycline antibiotics. Monte Carlo simulations were used for explorations of the clay layer spacing required for the adsorption of the antibiotic under different hydration states of the clay interlayer; these preliminary results were validated with previous X-ray diffraction patterns obtained following sorption experiments of OTC with MONT. Molecular dynamics relaxation simulations were performed subsequently in order to obtain geometry-optimized structures of the binding conformations of the intercalated antibiotic in the model MONT layers. This study contributes to a mechanistic understanding of the factors controlling the interlayer adsorption of the tetracycline antibiotics by the expandable smectite clay minerals. Figure 1. Optimized Monte Carlo simulation cell of OTC in the interlayer of MONT: perspective side view (top) and bottom view (bottom).

Competitive Sorption of CO2 and H2O in 2:1 Layer Phyllosilicates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaef, Herbert T.; Loring, John S.; Glezakou, Vassiliki Alexandra

The salting out effect, where increasing the ionic strength of aqueous solutions decreases the solubility of dissolved gases is a well-known phenomenon. Less explored is the opposite process where an initially anhydrous system containing a volatile, relatively non-polar component and inorganic ions is systematically hydrated. Expandable clays such as montmorillonite are ideal systems for exploring this scenario as they have readily accessible exchange sites containing cations that can be systematically dehydrated or hydrated, from near anhydrous to almost bulk-like water conditions. This phenomenon has new significance with the simultaneous implementation of geological sequestration and secondary utilization of CO2 to bothmore » mitigate climate warming and enhance extraction of methane from hydrated clay-rich formations. Here, the partitioning of CO2 and H2O between Na-, Ca-, and Mg-exchanged montmorillonite and variably hydrated supercritical CO2 (scCO2) was investigated using in situ X-ray diffraction, infrared (IR)spectroscopic titrations, and quartz crystal microbalance (QCM) measurements. Density functional theory calculations provided mechanistic insights. Structural volumetric changes were correlated to quantified changes in sorbed H2O and CO2 concentrations as a function of %H2O saturated in scCO2. Intercalation of CO2 is favored at low H2O/CO2 ratios in the interlayer region, where CO2 can solvate the interlayer cation. As the clay becomes more hydrated and the H2O/CO2 ratio increases, H2O displaces CO2 from the solvation shell of the cation and CO2 tends to segregate. This transition decreases both the entropic and enthalpic driving force for CO2 intercalation, consistent with experimentally observed loss of intercalated CO2.« less

Formation and Restacking of Disordered Smectite Osmotic Hydrates

DOE PAGES

Gilbert, Benjamin; Comolli, Luis R.; Tinnacher, Ruth M.; ...

2015-12-01

Clay swelling, an important phenomenon in natural systems, can dramatically affect the properties of soils and sediments. Something of particular interest in low-salinity, saturated systems are osmotic hydrates, forms of smectite in which the layer separation greatly exceeds the thickness of a single smectite layer due to the intercalation of water. In situ X-ray diffraction (XRD) studies have shown a strong link between ionic strength and average interlayer spacing in osmotic hydrates but also indicate the presence of structural disorder that has not been fully described. In the present study the structural state of expanded smectite in sodium chloride solutionsmore » was investigated by combining very low electron dose, high-resolution cryogenic-transmission electron microscopy observations with XRD experiments. Wyoming smectite (SWy-2) was embedded in vitreous ice to evaluate clay structure in aqua. Lattice-fringe images showed that smectite equilibrated in aqueous, low-ionic-strength solutions, exists as individual smectite layers, osmotic hydrates composed of parallel layers, as well as disordered layer conformations. There was no evidence found here for edge-to-sheet attractions, but significant variability in interlayer spacing was observed. Whether this variation could be explained by a dependence of the magnitude of long-range cohesive (van der Waals) forces on the number of layers in a smectite particle was investigated here. Calculations of the Hamaker constant for layer-layer interactions showed that van der Waals forces may span at least five layers plus the intervening water and confirmed that forces vary with layer number. The drying of the disordered osmotic hydrates induced re-aggregation of the smectite to form particles that exhibited coherent scattering domains. Clay disaggregation and restacking may be considered as an example of oriented attachment, with the unusual distinction that it may be cycled repeatedly by changing solution conditions.« less

Formation and Restacking of Disordered Smectite Osmotic Hydrates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilbert, Benjamin; Comolli, Luis R.; Tinnacher, Ruth M.

Clay swelling, an important phenomenon in natural systems, can dramatically affect the properties of soils and sediments. Something of particular interest in low-salinity, saturated systems are osmotic hydrates, forms of smectite in which the layer separation greatly exceeds the thickness of a single smectite layer due to the intercalation of water. In situ X-ray diffraction (XRD) studies have shown a strong link between ionic strength and average interlayer spacing in osmotic hydrates but also indicate the presence of structural disorder that has not been fully described. In the present study the structural state of expanded smectite in sodium chloride solutionsmore » was investigated by combining very low electron dose, high-resolution cryogenic-transmission electron microscopy observations with XRD experiments. Wyoming smectite (SWy-2) was embedded in vitreous ice to evaluate clay structure in aqua. Lattice-fringe images showed that smectite equilibrated in aqueous, low-ionic-strength solutions, exists as individual smectite layers, osmotic hydrates composed of parallel layers, as well as disordered layer conformations. There was no evidence found here for edge-to-sheet attractions, but significant variability in interlayer spacing was observed. Whether this variation could be explained by a dependence of the magnitude of long-range cohesive (van der Waals) forces on the number of layers in a smectite particle was investigated here. Calculations of the Hamaker constant for layer-layer interactions showed that van der Waals forces may span at least five layers plus the intervening water and confirmed that forces vary with layer number. The drying of the disordered osmotic hydrates induced re-aggregation of the smectite to form particles that exhibited coherent scattering domains. Clay disaggregation and restacking may be considered as an example of oriented attachment, with the unusual distinction that it may be cycled repeatedly by changing solution conditions.« less

Carbon nanoscroll-silk crystallite hybrid structures with controllable hydration and mechanical properties.

PubMed

Cheng, Yuan; Koh, Leng-Duei; Wang, Fan; Li, Dechang; Ji, Baohua; Yeo, Jingjie; Guan, Guijian; Han, Ming-Yong; Zhang, Yong-Wei

2017-07-06

Hybrid structures of nanomaterials (e.g. tubes, scrolls, threads, cages) and biomaterials (e.g. proteins) hold tremendous potential for applications as drug carriers, biosensors, tissue scaffolds, cancer therapeutic agents, etc. However, in many cases, the interacting forces at the nano-bio interfaces and their roles in controlling the structures and dynamics of nano-bio-hybrid systems are very complicated but poorly understood. In this study, we investigate the structure and mechanical behavior of a protein-based hybrid structure, i.e., a carbon nanoscroll (CNS)-silk crystallite with a hydration level controllable by an interlayer interaction in CNS. Our findings demonstrate that CNS with a reduced core size not only shields the crystallite from a weakening effect of water, but also markedly strengthens the crystallite. Besides water shielding, the enhanced strength arises from an enhanced interaction between the crystallite and CNS due to the enhanced interlayer interaction in CNS. In addition, the interfacial strength for pulling the crystallite out of the CNS-silk structure is found to be dependent on both the interlayer interaction energy in CNS as well as the sequence of protein at the CNS-silk interface. The present study is of significant value in designing drugs or protein delivery vehicles for biomedical applications, and serves as a general guide in designing novel devices based on rolled-up configurations of two-dimensional (2D) materials.

Thermodynamics, kinetics, and mechanics of cesium sorption in cement paste: A multiscale assessment

NASA Astrophysics Data System (ADS)

Arayro, Jack; Dufresne, Alice; Zhou, Tingtao; Ioannidou, Katerina; Ulm, Josef-Franz; Pellenq, Roland; Béland, Laurent Karim

2018-05-01

Cesium-137 is a common radioactive byproduct found in nuclear spent fuel. Given its 30 year half life, its interactions with potential storage materials—such as cement paste—is of crucial importance. In this paper, simulations are used to establish the interaction of calcium silicate hydrates (C-S-H)—the main binding phase of cement paste—with Cs at the nano- and mesoscale. Different C-S-H compositions are explored, including a range of Ca/Si ratios from 1.0 to 2.0. These calculations are based on a set of 150 atomistic models, which qualitatively and quantitatively reproduce a number of experimentally measured features of C-S-H—within limits intrinsic to the approximations imposed by classical molecular dynamics and the steps followed when building the models. A procedure where hydrated Ca2 + ions are swapped for Cs1 + ions shows that Cs adsorption in the C-S-H interlayer is preferred to Cs adsorption at the nanopore surface when Cs concentrations are lower than 0.19 Mol/kg. Interlayer sorption decreases as the Ca/Si ratio increases. The activation relaxation technique nouveau is used to access timescales out of the reach of traditional molecular dynamics (MD). It indicates that characteristic diffusion time for Cs1 + in the C-S-H interlayer is on the order of a few hours. Cs uptake in the interlayer has little impact on the elastic response of C-S-H. It leads to swelling of the C-S-H grains, but mesoscale calculations that access length scales out of the range of MD indicate that this leads to practically negligible expansive pressures for Cs concentrations relevant to nuclear waste repositories.

In situ XRD Study of Ca2+ Saturated Montmorillonite (STX-1) Exposed to Anhydrous and Wet Supercritical Carbon Dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaef, Herbert T.; Ilton, Eugene S.; Qafoku, Odeta

2012-01-09

Reactions involving scCO2 and a calcium saturated dioctahedral smectite (Ca-STX-1) were examined by in situ high-pressure x-ray diffraction over a range of temperatures (50° to 100°C) and pressures (90, 125, and 180 bar) relevant to long term geologic storage of CO2. Exposure of Ca-STX-1 containing one water of hydration (1W) to anhydrous scCO2 at 50°C and 90 bar produced an immediate increase of ~0.8 Å in the d001 basal reflection that was sustained for the length of the experiment (~44 hours). Higher ordered basal reflections displayed similar shifts. Following depressurization, positions of basal reflections and FWHM values (d001) returned tomore » initial values, with no measurable modification to the clay structure or water content. Similar results were obtained for tests conducted at 50°C and higher pressures (125 and 180 bar). Exposure of Ca-STX-1 containing two waters of hydration (2W) to scCO2 resulted in a decrease in the d001 reflection from 14.48 Å to 12.52 Å, after pressurization, indicating a partial loss of interlayer water. In addition, the hydration state of the clay became more homogeneous during contact with anhydrous scCO2 and after depressurization. In the presence of scCO2 and water, the clay achieved a 3W hydration state, based on a d001 spacing of 18.8 Å. In contrast to scCO2, comparable testing with N2 gas indicated trivial changes in the d001 series regardless of hydration state (1W or 2W). In the presence of free water and N2, the basal spacing for the Ca-STX-1 expanded slightly, but remained in the 2W hydration state. These experiments indicate that scCO2 can intercalate hydrated clays, where the 1W hydrate state is stable when exposed to anhydrous scCO2 under conditions proposed for geologic storage of CO2. Consequently, clays can act as secondary CO2 traps where potential collapse or expansion of the interlayer spacing depends on the initial hydration state of the clay and scCO2.« less

Structure and Dynamics of Confined Water and CO2 in Clays under Supercritical Conditions

NASA Astrophysics Data System (ADS)

Glezakou, V.; Lee, M.; Schaef, T.; Loring, J.; Davidson, C.; McGrail, P.

2013-12-01

Carbon dioxide (CO2) driven enhanced gas recovery (EGR) from depleted fractured shale gas reservoirs has the potential for producing economic benefits and providing long term storage options for anthropogenic derived CO2 emissions. However key scientific processes related to CO2:CH4 exchange rates, mineral volume changes, organic mobility, and mineral stability in the presence of acid gas injections are not well understood. In this paper, we conduct atomistic simulations to examine interactions occurring between model clay minerals and supercritical CO2 equilibrated with water or brines to identify parameters controlling adsorption and desorption of gases. Integrated within these simulations are results derived from a set of newly developed experimental techniques designed to characterize physico-chemical reactions at reservoir conditions. In a series of cell optimizations under pressures relevant to sequestration scenarios, molecular simulations within the NVT and NPT ensembles with varying water/CO2 ratios showed a range of interlayer expansion for specific cation-saturated smectites. In conjunction with experimental in situ high pressure x-ray diffraction (HXRD), semi-quantitative concentrations of interlayer H2O and CO2 were established. For example, Ca saturated smectites maintaining sub-single to single hydration states (<1W to 1W), expand approximately 1.7-2.0 Å when exposed to anhydrous supercritical CO2. In contrast, for single to double hydration states (1W-2W), the simulations indicate formation of a quasi-single, metastable state, leading to a reduced interlayer spacing. Partial dehydration of the interlayer spacing while in contact with CO2 is due to a reduction of the interlayer cation coordination number. Structural analysis of the intercalated species shows an increase in the hydrogen bonding between waters during CO2 intercalation coincident with a decrease in the coordination population around the cations. Power spectra reveal rotationally constrained CO2 molecules over the silica layer of the Ca-smectite surface due to the formation of a two dimensional supercritical CO2 network at lower pressures, expanding to three-dimensions as the water content increases. Diffusion coefficients of the interlayer species determined from the molecular trajectories show dependence on the presence of CO2 and hydration state. In agreement with modeling studies, direct observations of volume changes were observed during in situ HXRD experiments when exposure of a 2W Ca-smectite to supercritical CO2 at 50 °C and 90 bar produced a decrease in the interlayer spacing. In addition to intercalation, surface adsorption and desorption are equally important interactions occurring with clay minerals in the presence of supercritical CO2. Processes related to surface condensation of CO2 were examined through a series of modeling exercises and in situ spectroscopic measurements. Results showed that adsorbed CO2 concentrations were low when no water was adsorbed to the clay, but dramatically increased to a maximum when the clay was at ~1W. With continued water adsorption, CO2 concentrations decreased as the water outcompeted CO2 for adsorption/intercalation sites.

Effect of Layer Charge on CO2 and H2O Intercalations in Swelling Clays.

PubMed

Rao, Qi; Leng, Yongsheng

2016-11-08

The effect of layer charge on the intercalation of supercritical carbon dioxide (scCO 2 )-H 2 O mixture in Na-montmorillonite clay interlayers under T = 323 K and P = 90 bar geologic sequestration conditions has been further investigated. This effect includes the charge amount and its location (within either octahedral or tetrahedral layers due to isomorphic substitutions). Two clay models with different layer charges are used in this study. Simulation results show that the increase of charge amount shifts the monolayer-to-bilayer (1W-to-2W) hydration transition toward the lower relative humidity (RH), increasing water sorption at the expense of reducing the overall sorption amount of CO 2 in the clay interlayer. However, the combination of the influence of charge amount and charge location leads to insignificant changes in equilibrium basal spacings of the high- and low-charge clays. Molecular dynamics simulations show that the CO 2 dimers, which are frequently seen in low-charge clay interlayers, vanish in high-charge clay interlayers even at low RH of 30%.

Molecular Simulation Models of Carbon Dioxide Intercalation in Hydrated Sodium Montmorillonite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myshakin, Evgeniy; Saidi, Wissam; Romanov, Vyacheslav

2016-11-22

In this study, classical molecular dynamics simulations and density functional theory (DFT)-based molecular dynamics are used to elucidate the process of CO 2 intercalation into hydrated Na-montmorillonite at P-T conditions relevant to geological formations suitable for CO 2 storage. Of particular interest are the structural and transport properties of interlayer species after CO 2 intercalation. The conducted simulations allowed the research team to quantify expansion/contraction of smectite as a function of CO 2 and H 2O compositions. The resulting swelling curves can be used to gauge the amount of stored CO 2, compare it to the experiment, and estimate changesmore » in geomechanical properties of the storage formation. The obtained results showed that the infrared signal of the asymmetric stretch vibration of CO 2 molecule is extremely sensitive to the solvent environment. The extent of the frequency shift relative to the gas-phase value can be used to probe hydration level in the interlayer with intercalated CO 2. Interaction of supercritical CO 2 with brine in deep geological formations promotes an increase of hydrophobicity of clay surfaces. As a result of wettability alteration, estimated diffusion constants of CO 2 and H 2O increase with the increased CO 2 load; this can contribute to faster migration of CO 2 throughout the formation.« less

Effects of exchanged cation and layer charge on the sorption of water and EGME vapors on montmorillonite clays

USGS Publications Warehouse

Chiou, Cary T.; Rutherford, David W.

1997-01-01

The effects of exchanged cation and layer charge on the sorption of water and ethylene glycol monoethyl ether (EGME) vapors on montmorillonite have been studied on SAz-1 and SWy-1 source clays, each exchanged respectively with Ca, Na, K, Cs and tetramethylammonium (TMA) cations. The corresponding lattice expansions were also determined, and the corresponding N2 adsorption data were provided for comparison. For clays exchanged with cations of low hydrating powers (such as K, Cs and TMA), water shows a notably lower uptake than does N2 at low relative pressures (P/P0). By contrast, EGME shows higher uptakes than N2 on all exchanged clays at all P/P0. The anomaly for water is attributed to its relatively low attraction for siloxane surfaces of montmorillonite because of its high cohesive energy density. In addition to solvating cations and expanding interlayers, water and EGME vapors condense into small clay pores and interlayer voids created by interlayer expansion. The initial (dry) interlayer separation varies more significantly with cation type than with layer charge; the water-saturated interlayer separation varies more with cation type than the EGME-saturated interlayer separation. Because of the differences in surface adsorption and interlayer expansion for water and EGME, no general correspondence is found between the isotherms of water and EGME on exchanged clays, nor is a simple relation observed between the overall uptake of either vapor and the cation solvating power. The excess interlayer capacities of water and of EGME that result from lattice expansion of the exchanged clays are estimated by correcting for amounts of vapor adsorption on planar clay surfaces and of vapor condensation into intrinsic clay pores. The resulting data follow more closely the relative solvating powers of the exchanged cations.

Stability of hydrated minerals on Mars

NASA Astrophysics Data System (ADS)

Cloutis, Edward A.; Craig, Michael A.; Mustard, John F.; Kruzelecky, Roman V.; Jamroz, Wes R.; Scott, Alan; Bish, David L.; Poulet, François; Bibring, Jean-Pierre; King, Penelope L.

2007-10-01

The validity of recent identification of various hydrated minerals (kieserite, gypsum, hexahydrite, nontronite, chamosite, and montmorillonite) on Mars was assessed by exposing these minerals to simulated Martian surface conditions of atmospheric composition and pressure, temperature, and ultraviolet light irradiation. When exposed to such conditions the hydrated minerals exhibit in general, greater losses of interlayer H2O than structural OH. Minerals such as gypsum that contain structural H2O are more resistant to H2O loss than phyllosilicates. The partial loss of OH in some of the phyllosilicates is not accompanied by a measurable and systematic change in the wavelength position or intensity of metal-OH absorption bands. The characteristic absorption features that allow for identification of these minerals on Mars may be reduced in intensity, but are nevertheless largely preserved.

Enhanced sorption of trichloroethene by smectite clay exchanged with Cs+.

PubMed

Aggarwal, Vaneet; Li, Hui; Boyd, Stephen A; Teppen, Brian J

2006-02-01

Trichloroethene (TCE) is one of the most common pollutants in groundwater, and Cs+ can be a cocontaminant at nuclear facilities. Smectite clays have large surface areas, are common in soils, have high affinities for some organic contaminants, and hence can potentially influence the transport of organic pollutants entering soils and sediments. The exchangeable cations present near smectite clay surfaces can radically influence the sorption of organic pollutants by soil clays. This research was undertaken to determine the effect of Cs+, and other common interlayer cations, such as K+ and Ca2+, on the sorption of TCE by a reference smectite clay saponite. Cs-saturated clay sorbed the most TCE, up to 3500 mg/kg, while Ca-saturated smectite sorbed the least. We hypothesize that the stronger sorption of TCE by the Cs-smectite can be attributed to the lower hydration energy and hence smaller hydrated radius of Cs+, which expands the lateral clay surface domains available for sorption. Also, Cs-smectite interlayers are only one or two water layers thick, which may drive capillary condensation of TCE. Our results implicate enhanced retention of TCE in aquifer materials containing smectites accompanied by Cs+ cocontamination.

Complete Defluorination of Perfluorinated Compounds by Hydrated Electrons Generated from 3-Indole-acetic-acid in Organomodified Montmorillonite

PubMed Central

Tian, Haoting; Gao, Juan; Li, Hui; Boyd, Stephen A.; Gu, Cheng

2016-01-01

Here we describe a unique process that achieves complete defluorination and decomposition of perfluorinated compounds (PFCs) which comprise one of the most recalcitrant and widely distributed classes of toxic pollutant chemicals found in natural environments. Photogenerated hydrated electrons derived from 3-indole-acetic-acid within an organomodified clay induce the reductive defluorination of co-sorbed PFCs. The process proceeds to completion within a few hours under mild reaction conditions. The organomontmorillonite clay promotes the formation of highly reactive hydrated electrons by stabilizing indole radical cations formed upon photolysis, and prevents their deactivation by reaction with protons or oxygen. In the constrained interlayer regions of the clay, hydrated electrons and co-sorbed PFCs are brought in close proximity thereby increasing the probability of reaction. This novel green chemistry provides the basis for in situ and ex situ technologies to treat one of the most troublesome, recalcitrant and ubiquitous classes of environmental contaminants, i.e., PFCs, utilizing innocuous reagents, naturally occurring materials and mild reaction conditions. PMID:27608658

A modeling study of methane hydrate decomposition in contact with the external surface of zeolites.

PubMed

Smirnov, Konstantin S

2017-08-30

The behavior of methane hydrate (MH) enclosed between the (010) surfaces of the silicalite-1 zeolite was studied by means of molecular dynamics simulations at temperatures of 150 and 250 K. Calculations reveal that the interaction with the hydrophilic surface OH groups destabilizes the clathrate structure of hydrate. While MH mostly conserves the structure in the simulation at the low temperature, thermal motion at the high temperature breaks the fragilized cages of H-bonded water molecules, thus leading to the release of methane. The dissociation proceeds in a layer-by-layer manner starting from the outer parts of the MH slab until complete hydrate decomposition. The released CH 4 molecules are absorbed by the microporous solid, whereas water is retained at the surfaces of hydrophobic silicalite and forms a meniscus in the interlayer space. Methane uptake reaches 70% of the silicalite sorption capacity. The energy necessary for the endothermic MH dissociation is supplied by the exothermic methane absorption by the zeolite.

Controlling interlayer interactions in vanadium pentoxide-poly(ethylene oxide) nanocomposites for enhanced magnesium-ion charge transport and storage

NASA Astrophysics Data System (ADS)

Perera, Sanjaya D.; Archer, Randall B.; Damin, Craig A.; Mendoza-Cruz, Rubén; Rhodes, Christopher P.

2017-03-01

Rechargeable magnesium batteries provide the potential for lower cost and improved safety compared with lithium-ion batteries, however obtaining cathode materials with highly reversible Mg-ion capacities is hindered by the high polarizability of divalent Mg-ions and slow solid-state Mg-ion diffusion. We report that incorporating poly(ethylene oxide) (PEO) between the layers of hydrated vanadium pentoxide (V2O5) xerogels results in significantly improved reversible Mg-ion capacities. X-ray diffraction and high resolution transmission electron microscopy show that the interlayer spacing between V2O5 layers was increased by PEO incorporation. Vibrational spectroscopy supports that the polymer interacts with the V2O5 lattice. The V2O5-PEO nanocomposite exhibited a 5-fold enhancement in Mg-ion capacity, improved stability, and improved rate capabilities compared with V2O5 xerogels. The Mg-ion diffusion coefficient of the nanocomposite was increased compared with that of V2O5 xerogels which is attributed to enhanced Mg-ion mobility due to the shielding interaction of PEO with the V2O5 lattice. This study shows that beyond only interlayer spacing, the nature of interlayer interactions of Mg-ions with V2O5, PEO, and H2O are key factors that affect Mg-ion charge transport and storage in layered materials. The design of layered materials with controlled interlayer interactions provides a new approach to develop improved cathodes for magnesium batteries.

Enhanced Photoreduction of Nitro-aromatic Compounds by Hydrated Electrons Derived from Indole on Natural Montmorillonite.

PubMed

Tian, Haoting; Guo, Yong; Pan, Bo; Gu, Cheng; Li, Hui; Boyd, Stephen A

2015-07-07

A new photoreduction pathway for nitro-aromatic compounds (NACs) and the underlying degradation mechanism are described. 1,3-Dinitrobenzene was reduced to 3-nitroaniline by the widely distributed aromatic molecule indole; the reaction is facilitated by montmorillonite clay mineral under both simulated and natural sunlight irradiation. The novel chemical reaction is strongly affected by the type of exchangeable cation present on montmorillonite. The photoreduction reaction is initiated by the adsorption of 1,3-dinitrobenzene and indole in clay interlayers. Under light irradiation, the excited indole molecule generates a hydrated electron and the indole radical cation. The structural negative charge of montmorillonite plausibly stabilizes the radical cation hence preventing charge recombination. This promotes the release of reactive hydrated electrons for further reductive reactions. Similar results were observed for the photoreduction of nitrobenzene. In situ irradiation time-resolved electron paramagnetic resonance and Fourier transform infrared spectroscopies provided direct evidence for the generation of hydrated electrons and the indole radical cations, which supported the proposed degradation mechanism. In the photoreduction process, the role of clay mineral is to both enhance the generation of hydrated electrons and to provide a constrained reaction environment in the galley regions, which increases the probability of contact between NACs and hydrated electrons.

Effects of humidity and interlayer cations on the frictional strength of montmorillonite

NASA Astrophysics Data System (ADS)

Tetsuka, Hiroshi; Katayama, Ikuo; Sakuma, Hiroshi; Tamura, Kenji

2018-04-01

We developed a humidity control system in a biaxial friction testing machine to investigate the effect of relative humidity and interlayer cations on the frictional strength of montmorillonite. We carried out the frictional experiments on Na- and Ca-montmorillonite under controlled relative humidities (ca. 10, 30, 50, 70, and 90%) and at a constant temperature (95 °C). Our experimental results show that frictional strengths of both Na- and Ca-montmorillonite decrease systematically with increasing relative humidity. The friction coefficients of Na-montmorillonite decrease from 0.33 (at relative humidity of 10%) to 0.06 (at relative humidity of 93%) and those of Ca-montmorillonite decrease from 0.22 (at relative humidity of 11%) to 0.04 (at relative humidity of 91%). Our results also show that the frictional strength of Na-montmorillonite is higher than that of Ca-montmorillonite at a given relative humidity. These results reveal that the frictional strength of montmorillonite is sensitive to hydration state and interlayer cation species, suggesting that the strength of faults containing these clay minerals depends on the physical and chemical environment.[Figure not available: see fulltext.

General synthesis and structural evolution of a layered family of Ln8(OH)20Cl4 x nH2O (Ln = Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, and Y).

PubMed

Geng, Fengxia; Matsushita, Yoshitaka; Ma, Renzhi; Xin, Hao; Tanaka, Masahiko; Izumi, Fujio; Iyi, Nobuo; Sasaki, Takayoshi

2008-12-03

The synthesis process and crystal structure evolution for a family of stoichiometric layered rare-earth hydroxides with general formula Ln(8)(OH)(20)Cl(4) x nH(2)O (Ln = Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, and Y; n approximately 6-7) are described. Synthesis was accomplished through homogeneous precipitation of LnCl(3) x xH(2)O with hexamethylenetetramine to yield a single-phase product for Sm-Er and Y. Some minor coexisting phases were observed for Nd(3+) and Tm(3+), indicating a size limit for this layered series. Light lanthanides (Nd, Sm, Eu) crystallized into rectangular platelets, whereas platelets of heavy lanthanides from Gd tended to be of quasi-hexagonal morphology. Rietveld profile analysis revealed that all phases were isostructural in an orthorhombic layered structure featuring a positively charged layer, [Ln(8)(OH)(20)(H(2)O)(n)](4+), and interlayer charge-balancing Cl(-) ions. In-plane lattice parameters a and b decreased nearly linearly with a decrease in the rare-earth cation size. The interlamellar distance, c, was almost constant (approximately 8.70 A) for rare-earth elements Nd(3+), Sm(3+), and Eu(3+), but it suddenly decreased to approximately 8.45 A for Tb(3+), Dy(3+), Ho(3+), and Er(3+), which can be ascribed to two different degrees of hydration. Nd(3+) typically adopted a phase with high hydration, whereas a low-hydration phase was preferred for Tb(3+), Dy(3+), Ho(3+), Er(3+), and Tm(3+). Sm(3+), Eu(3+), and Gd(3+) samples were sensitive to humidity conditions because high- and low-hydration phases were interconvertible at a critical humidity of 10%, 20%, and 50%, respectively, as supported by both X-ray diffraction and gravimetry as a function of the relative humidity. In the phase conversion process, interlayer expansion or contraction of approximately 0.2 A also occurred as a possible consequence of absorption/desorption of H(2)O molecules. The hydration difference was also evidenced by refinement results. The number of coordinated water molecules per formula weight, n, changed from 6.6 for the high-hydration Gd sample to 6.0 for the low-hydration Gd sample. Also, the hydration number usually decreased with increasing atomic number; e.g., n = 7.4, 6.3, 7.2, and 6.6 for high-hydration Nd, Sm, Eu, and Gd, and n = 6.0, 5.8, 5.6, 5.4, and 4.9 for low-hydration Gd, Tb, Dy, Ho, and Er. The variation in the average Ln-O bond length with decreasing size of the lanthanide ions is also discussed. This family of layered lanthanide compounds highlights a novel chemistry of interplay between crystal structure stability and coordination geometry with water molecules.

Effect of organic matters on CO2 hydrate phase equilibrium conditions in Na-montmorillonite clay

NASA Astrophysics Data System (ADS)

Park, T.; Kyung, D.; Lee, W.

2013-12-01

Formation of gas hydrates provides an attractive idea for storing greenhouse gases in a long-term stable geological formation. Since the phase equilibrium conditions of gas hydrates indicate the stability of hydrates, estimation of the phase equilibrium conditions of gas hydrates in marine geological conditions is necessary. In this study, we have identified the effects of organic matters (glycine, glucose, and urea) and solid surface (montmorillonite (MMT)) on the three-phase (liquid-hydrate-vapor) equilibrium conditions of CO2 hydrate. CO2 phase equilibrium experiments were conducted using 0.5mol% organic matter solutions with and without 10g soil mineral were experimentally conducted. Addition of organic matters shifted the phase equilibrium conditions of CO2 hydrate to the higher pressure or lower pressure region because of higher competition of water molecules due to the dissolved organic matters. Presence of MMT also leaded to the higher equilibrium pressure due to the interaction of cations with water molecules. By addition of organic matters to the clay suspension, the hydrate phase equilibrium conditions were less inhibited compared to those of MMT and organic matters independently. The diminished magnitudes by addition of organic matters to the clay suspension (MMT > MMT+urea > MMT+glycine > MMT+glucose > DIW) were different to the order of inhibition degree without MMT (Glucose > glycine > urea > DIW). X-ray diffraction (XRD), scanning electron microscope (SEM), and ion chromatography (IC) analysis were conducted to support the hypothesis that the organic matters interact with cations in MMT interlayer space, and leads to the less inhibition of phase equilibrium conditions. The present study provides basic information for the formation and dissociation of CO2 hydrates in the geological formation when sequestering CO2 as a form of CO2 hydrate.

Dynamics of radiocesium exchange and interstratification in anhydrous clay interlayers: Bridging the atom and single crystal scales

NASA Astrophysics Data System (ADS)

Lammers, L. N.; Pestana, L. R.; Schaettle, K. B.; Head-Gordon, T.

2016-12-01

High structural charge clay minerals govern the transport and retention of radiocesium in soils and clay-rich geologic repositories. Cation exchange capacities in these phases are typically assumed to be limited to fast-exchanging basal and high-affinity edge sites, while ions in anhydrous interlayers, usually K+, are considered non-exchangeable. However, recent high resolution imaging and spectroscopic studies have demonstrated that Cs ions can in fact exchange with interlayer K without the formation of a hydrated intermediate.1,2 These exchange reactions result in sharp exchange fronts wherein K+ ions are completely replaced by Cs+ at the exchange interface, and the rate of exchange varies from layer to layer, resulting in the formation of interstratified structures (i.e., randomly alternating layers of exchanged and pristine interlayers). Currently, this process cannot be explained by any known exchange mechanism, and consequently, no kinetic expressions are available to account for this phenomenon in models of subsurface radiocesium fate and transport. We present a mesoscale model for direct exchange in anhydrous clay interlayers that is based on the kinetics of single ion migration events. Single atom migration kinetics derived from density functional theory (DFT) calculations are used as inputs to kinetic Monte Carlo (kMC) simulations, which capture the collective dynamics of the exchange process over length- and timescales relevant for implementation in reactive transport models. Potential energy surfaces derived from DFT demonstrate that exchange of Cs+ for K+ in anhydrous interlayers lowers the energy barrier to K ion migration by 145 kJ/mol, leading to a positive feedback mechanism that generates atomically sharp exchange fronts. Our work demonstrates the application of "coarse-graining" techniques to develop models for processes with characteristic length- and timescales not accessible by direct atomistic simulation. 1 Okumura T. et al. (2014) Direct observation of cesium at the interlayer region in phlogopite mica. Microscopy 63(1), 65-72. 2 Fuller A. J. et al. (2015) Caesium incorporation and retention in illite interlayers. Appl. Clay Sci. 108, 128-134.

Ion sieving in graphene oxide membranes via cationic control of interlayer spacing

NASA Astrophysics Data System (ADS)

Chen, Liang; Shi, Guosheng; Shen, Jie; Peng, Bingquan; Zhang, Bowu; Wang, Yuzhu; Bian, Fenggang; Wang, Jiajun; Li, Deyuan; Qian, Zhe; Xu, Gang; Liu, Gongping; Zeng, Jianrong; Zhang, Lijuan; Yang, Yizhou; Zhou, Guoquan; Wu, Minghong; Jin, Wanqin; Li, Jingye; Fang, Haiping

2017-10-01

Graphene oxide membranes—partially oxidized, stacked sheets of graphene—can provide ultrathin, high-flux and energy-efficient membranes for precise ionic and molecular sieving in aqueous solution. These materials have shown potential in a variety of applications, including water desalination and purification, gas and ion separation, biosensors, proton conductors, lithium-based batteries and super-capacitors. Unlike the pores of carbon nanotube membranes, which have fixed sizes, the pores of graphene oxide membranes—that is, the interlayer spacing between graphene oxide sheets (a sheet is a single flake inside the membrane)—are of variable size. Furthermore, it is difficult to reduce the interlayer spacing sufficiently to exclude small ions and to maintain this spacing against the tendency of graphene oxide membranes to swell when immersed in aqueous solution. These challenges hinder the potential ion filtration applications of graphene oxide membranes. Here we demonstrate cationic control of the interlayer spacing of graphene oxide membranes with ångström precision using K+, Na+, Ca2+, Li+ or Mg2+ ions. Moreover, membrane spacings controlled by one type of cation can efficiently and selectively exclude other cations that have larger hydrated volumes. First-principles calculations and ultraviolet absorption spectroscopy reveal that the location of the most stable cation adsorption is where oxide groups and aromatic rings coexist. Previous density functional theory computations show that other cations (Fe2+, Co2+, Cu2+, Cd2+, Cr2+ and Pb2+) should have a much stronger cation-π interaction with the graphene sheet than Na+ has, suggesting that other ions could be used to produce a wider range of interlayer spacings.

CO 2 Sorption to Subsingle Hydration Layer Montmorillonite Clay Studied by Excess Sorption and Neutron Diffraction Measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rother, Gernot; Ilton, Eugene S.; Wallacher, Dirk

2013-01-02

Geologic storage of CO 2 requires that the caprock sealing the storage rock is highly impermeable to CO 2. Swelling clays, which are important components of caprocks, may interact with CO 2 leading to volume change and potentially impacting the seal quality. The interactions of supercritical (sc) CO 2 with Na saturated montmorillonite clay containing a subsingle layer of water in the interlayer region have been studied by sorption and neutron diffraction techniques. The excess sorption isotherms show maxima at bulk CO2 densities of ≈0.15 g/cm 3, followed by an approximately linear decrease of excess sorption to zero and negativemore » values with increasing CO 2 bulk density. Neutron diffraction experiments on the same clay sample measured interlayer spacing and composition. The results show that limited amounts of CO 2 are sorbed into the interlayer region, leading to depression of the interlayer peak intensity and an increase of the d(001) spacing by ca. 0.5 Å. The density of CO 2 in the clay pores is relatively stable over a wide range of CO 2 pressures at a given temperature, indicating the formation of a clay-CO 2 phase. Finally, at the excess sorption maximum, increasing CO 2 sorption with decreasing temperature is observed while the high-pressure sorption properties exhibit weak temperature dependence.« less

Luminescence and ESR studies of relationships between O(-)-centres and structural iron in natural and synthetically hydrated kaolinites

NASA Technical Reports Server (NTRS)

Coyne, L. M.; Costanzo, P. M.; Theng, B. K.

1989-01-01

Luminescence, induced by dehydration and by wetting with hydrazine and unsymmetrically substituted hydrazine, and related ESR spectra have been observed from several kaolinites, synthetically hydrated kaolinites, and metahalloysites. The amine-wetting luminescence results suggest that intercalation, not a chemiluminescence reaction, is the luminescence trigger. Correlation between hydration-induced luminescence and g = 2 ESR signals associated with O(-)-centres in several natural halloysites, and concurrent diminution of the intensity of both these signal types as a function of aging in two 8.4 angstroms synthetically hydrated, kaolinites, confirm a previously-reported relationship between the luminescence induced by dehydration and in the presence of O(-)-centres (holes, i.e., electron vacancies) in the tetrahedral sheet. Furthermore, the ESR spectra of the 8.4 angstroms hydrate showed a concurrent change in the line shape of the g = 4 signal from a shape usually associated with structural Fe in an ordered kaolinite, to a simpler one typically observed in more disordered kaolinite, halloysite, and montmorillonite. Either structural Fe centres and the O(-)-centres interact, or both are subject to factors previously associated with degree of order. The results question the long-term stability of the 8.4 angstroms hydrate, although XRD does not indicate interlayer collapse over this period. Complex inter-relationships are shown between intercalation, stored energy, structural Fe, and the degree of hydration which may be reflected in catalytic as well as spectroscopic properties of the clays.

Neural network analysis of crosshole tomographic images: The seismic signature of gas hydrate bearing sediments in the Mackenzie Delta (NW Canada)

NASA Astrophysics Data System (ADS)

Bauer, K.; Pratt, R. G.; Haberland, C.; Weber, M.

2008-10-01

Crosshole seismic experiments were conducted to study the in-situ properties of gas hydrate bearing sediments (GHBS) in the Mackenzie Delta (NW Canada). Seismic tomography provided images of P velocity, anisotropy, and attenuation. Self-organizing maps (SOM) are powerful neural network techniques to classify and interpret multi-attribute data sets. The coincident tomographic images are translated to a set of data vectors in order to train a Kohonen layer. The total gradient of the model vectors is determined for the trained SOM and a watershed segmentation algorithm is used to visualize and map the lithological clusters with well-defined seismic signatures. Application to the Mallik data reveals four major litho-types: (1) GHBS, (2) sands, (3) shale/coal interlayering, and (4) silt. The signature of seismic P wave characteristics distinguished for the GHBS (high velocities, strong anisotropy and attenuation) is new and can be used for new exploration strategies to map and quantify gas hydrates.

Nutrition and Hydration Status of Aircrew Members Consuming The Food Packet, Survival, General Purpose, Improved During A Simulated Survival Scenario

DTIC Science & Technology

1992-11-01

AD-A25 8 744 AD Tl-93 REPORT NO NUTRITION AND HYDRATION STATUS OF AIRCREW MEMBERS CONSUMING THE FOOD PACKET, SURVIVAL, GENERAL PURPOSE, IMPROVED...TYPE AND DATES COVERED INovember 1992 IFinal: June 1991 - November 1992 4. TITLE AND SUBTITLE Nutrition and hydration status of aircrew ’- 5. FUNDING...Distribution is unlimited.. 13. ABSTRACT (Maximtum 200 words) Adequate nutrition and hydration can be crucial to the survival of downed aircrews. To determine

Aluminum-induced dreierketten chain cross-links increase the mechanical properties of nanocrystalline calcium aluminosilicate hydrate

NASA Astrophysics Data System (ADS)

Geng, Guoqing; Myers, Rupert J.; Li, Jiaqi; Maboudian, Roya; Carraro, Carlo; Shapiro, David A.; Monteiro, Paulo J. M.

2017-03-01

The incorporation of Al and increased curing temperature promotes the crystallization and cross-linking of calcium (alumino)silicate hydrate (C-(A-)S-H), which is the primary binding phase in most contemporary concrete materials. However, the influence of Al-induced structural changes on the mechanical properties at atomistic scale is not well understood. Herein, synchrotron radiation-based high-pressure X-ray diffraction is used to quantify the influence of dreierketten chain cross-linking on the anisotropic mechanical behavior of C-(A-)S-H. We show that the ab-planar stiffness is independent of dreierketten chain defects, e.g. vacancies in bridging tetrahedra sites and Al for Si substitution. The c-axis of non-cross-linked C-(A-)S-H is more deformable due to the softer interlayer opening but stiffens with decreased spacing and/or increased zeolitic water and Ca2+ of the interlayer. Dreierketten chain cross-links act as ‘columns’ to resist compression, thus increasing the bulk modulus of C-(A-)S-H. We provide the first experimental evidence on the influence of the Al-induced atomistic configurational change on the mechanical properties of C-(A-)S-H. Our work advances the fundamental knowledge of C-(A-)S-H on the lowest level of its hierarchical structure, and thus can impact the way that innovative C-(A-)S-H-based cementitious materials are developed using a ‘bottom-up’ approach.

Aluminum-induced dreierketten chain cross-links increase the mechanical properties of nanocrystalline calcium aluminosilicate hydrate.

PubMed

Geng, Guoqing; Myers, Rupert J; Li, Jiaqi; Maboudian, Roya; Carraro, Carlo; Shapiro, David A; Monteiro, Paulo J M

2017-03-10

The incorporation of Al and increased curing temperature promotes the crystallization and cross-linking of calcium (alumino)silicate hydrate (C-(A-)S-H), which is the primary binding phase in most contemporary concrete materials. However, the influence of Al-induced structural changes on the mechanical properties at atomistic scale is not well understood. Herein, synchrotron radiation-based high-pressure X-ray diffraction is used to quantify the influence of dreierketten chain cross-linking on the anisotropic mechanical behavior of C-(A-)S-H. We show that the ab-planar stiffness is independent of dreierketten chain defects, e.g. vacancies in bridging tetrahedra sites and Al for Si substitution. The c-axis of non-cross-linked C-(A-)S-H is more deformable due to the softer interlayer opening but stiffens with decreased spacing and/or increased zeolitic water and Ca 2+ of the interlayer. Dreierketten chain cross-links act as 'columns' to resist compression, thus increasing the bulk modulus of C-(A-)S-H. We provide the first experimental evidence on the influence of the Al-induced atomistic configurational change on the mechanical properties of C-(A-)S-H. Our work advances the fundamental knowledge of C-(A-)S-H on the lowest level of its hierarchical structure, and thus can impact the way that innovative C-(A-)S-H-based cementitious materials are developed using a 'bottom-up' approach.

Densification of the interlayer spacing governs the nanomechanical properties of calcium-silicate-hydrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geng, Guoqing; Myers, Rupert J.; Qomi, Mohammad Javad Abdolhosseini

Calciuam-silicate-hydrate (C-S-H) is the principal binding phase in modern concrete. Molecular simulations imply that its nanoscale stiffness is 'defect-driven', i.e., dominated by crystallographic defects such as bridging site vacancies in its silicate chains. However, experimental validation of this result is difficult due to the hierarchically porous nature of C-S-H down to nanometers. Here in this paper, we integrate high pressure X-ray diffraction and atomistic simulations to correlate the anisotropic deformation of nanocrystalline C-S-H to its atomic-scale structure, which is changed by varying the Ca-To-Si molar ratio. Contrary to the 'defect-driven' hypothesis, we clearly observe stiffening of C-S-H with increasing Ca/Simore » in the range 0.8 ≤ Ca/Si ≤ 1.3, despite increasing numbers of vacancies in its silicate chains. The deformation of these chains along the b-Axis occurs mainly through tilting of the Si-O-Si dihedral angle rather than shortening of the Si-O bond, and consequently there is no correlation between the incompressibilities of the a-and b-Axes and the Ca/Si. On the contrary, the intrinsic stiffness of C-S-H solid is inversely correlated with the thickness of its interlayer space. This work provides direct experimental evidence to conduct more realistic modelling of C-S-H-based cementitious material.« less

Densification of the interlayer spacing governs the nanomechanical properties of calcium-silicate-hydrate

DOE PAGES

Geng, Guoqing; Myers, Rupert J.; Qomi, Mohammad Javad Abdolhosseini; ...

2017-09-08

Calciuam-silicate-hydrate (C-S-H) is the principal binding phase in modern concrete. Molecular simulations imply that its nanoscale stiffness is 'defect-driven', i.e., dominated by crystallographic defects such as bridging site vacancies in its silicate chains. However, experimental validation of this result is difficult due to the hierarchically porous nature of C-S-H down to nanometers. Here in this paper, we integrate high pressure X-ray diffraction and atomistic simulations to correlate the anisotropic deformation of nanocrystalline C-S-H to its atomic-scale structure, which is changed by varying the Ca-To-Si molar ratio. Contrary to the 'defect-driven' hypothesis, we clearly observe stiffening of C-S-H with increasing Ca/Simore » in the range 0.8 ≤ Ca/Si ≤ 1.3, despite increasing numbers of vacancies in its silicate chains. The deformation of these chains along the b-Axis occurs mainly through tilting of the Si-O-Si dihedral angle rather than shortening of the Si-O bond, and consequently there is no correlation between the incompressibilities of the a-and b-Axes and the Ca/Si. On the contrary, the intrinsic stiffness of C-S-H solid is inversely correlated with the thickness of its interlayer space. This work provides direct experimental evidence to conduct more realistic modelling of C-S-H-based cementitious material.« less

Densification of the interlayer spacing governs the nanomechanical properties of calcium-silicate-hydrate.

PubMed

Geng, Guoqing; Myers, Rupert J; Qomi, Mohammad Javad Abdolhosseini; Monteiro, Paulo J M

2017-09-08

Calciuam-silicate-hydrate (C-S-H) is the principal binding phase in modern concrete. Molecular simulations imply that its nanoscale stiffness is 'defect-driven', i.e., dominated by crystallographic defects such as bridging site vacancies in its silicate chains. However, experimental validation of this result is difficult due to the hierarchically porous nature of C-S-H down to nanometers. Here, we integrate high pressure X-ray diffraction and atomistic simulations to correlate the anisotropic deformation of nanocrystalline C-S-H to its atomic-scale structure, which is changed by varying the Ca-to-Si molar ratio. Contrary to the 'defect-driven' hypothesis, we clearly observe stiffening of C-S-H with increasing Ca/Si in the range 0.8 ≤ Ca/Si ≤ 1.3, despite increasing numbers of vacancies in its silicate chains. The deformation of these chains along the b-axis occurs mainly through tilting of the Si-O-Si dihedral angle rather than shortening of the Si-O bond, and consequently there is no correlation between the incompressibilities of the a- and b-axes and the Ca/Si. On the contrary, the intrinsic stiffness of C-S-H solid is inversely correlated with the thickness of its interlayer space. This work provides direct experimental evidence to conduct more realistic modelling of C-S-H-based cementitious material.

[PREVALENCE OF DEHYDRATION BEFORE TRAINING IN PROFESIONAL CHILEAN SOCCER PLAYERS].

PubMed

Castro-Sepúlveda, Mauricio; Astudillo, Sebastian; Álvarez, Cristian; Zapata-Lamana, Rafael; Zbinden-Foncea, Hermann; Ramírez-Campillo, Rodrigo; Jorquera, Carlos

2015-07-01

there is a lack of studies concerning hydration status before training in professional soccer player. to describe hydration status before regular training practices in professional soccer players. a total of 156 male soccer players (age 25.4 ± 5.2 y) from six professional Chilean clubs were included. No hydration or food intake recommendations were made before experiment, with the aim to assess hydration status under athlete's regular "real" conditions. Body mass, height and urine specific gravity (USG) measurements were performed before training practices. 98% of athletes showed dehydration (between moderate and severe) before regular training practices. dehydration is the most prevalent hydration status in professional Chilean soccer players before training, which may negatively affect athlete's performance and may increase their risk of heat-related injuries. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Nano-confined water in the interlayers of hydrocalumite: Reorientational dynamics probed by neutron spectroscopy and molecular dynamics computer simulations

NASA Astrophysics Data System (ADS)

Kalinichev, A. G.; Faraone, A.; Udovic, T.; Kolesnikov, A. I.; de Souza, N. R.; Reinholdt, M. X.; Kirkpatrick, R.

2008-12-01

Layered double hydroxides (LDHs, anionic clays) represent excellent model systems for detailed molecular- level studies of the structure, dynamics, and energetics of nano-confined water in mineral interlayers and nano-pores, because LDH interlayers can have a well-defined structures and contain H2O molecules and a wide variety of anions in structurally well-defined positions and coordinations. [Ca2Al(OH)6]Cl·2H2O, also known as hydrocalumite or Friedel's salt, has a well- ordered Ca,Al distribution in the hydroxide layer and a very high degree of H2O,Cl ordering in the interlayer. It is also one of the only LDH phase for which a single crystal structure refinement is available. Thus, it is currently the best model compound for understanding the structure and dynamical behavior of interlayer and surface species in other, less-ordered, LDHs. We investigated the structural and dynamic behavior of water in the interlayers of hydrocalumite using inelastic (INS) and quasielastic (QENS) neutron scattering and molecular dynamics computer simulations. The comperehensive neutron scattering studies were performed for one fully hydrated and one dehydrated sample of hydrocalumite using several complementary instruments (HFBS, DCS and FANS at NCNR; HRMECS and QENS at IPNS) at temperatures above and below the previously discovered order-disorder interlayer phase transition. Together the experimental and molecular modeling results capture the important details of the dynamics of nano-confined water and the effects of the orientational ordering of H2O molecules above and below the phase transition. They provide otherwise unobtainable experimental information about the transformation of H2O librational and diffusional modes across the order-disorder phase transition and significantly add to our current understanding of the structure and dynamics of water in LDH phases based on the earlier NMR, IR, X-ray, and calorimetric measurements. The approach can now be extended to probe the dynamics of nano-confined and interfacial water in more disordered phases (LDH, clays, cement, etc.), for which much less initial structural information is available.

Clinical Variables Associated with Hydration Status in Acute Ischemic Stroke Patients with Dysphagia.

PubMed

Crary, Michael A; Carnaby, Giselle D; Shabbir, Yasmeen; Miller, Leslie; Silliman, Scott

2016-02-01

Acute stroke patients with dysphagia are at increased risk for poor hydration. Dysphagia management practices may directly impact hydration status. This study examined clinical factors that might impact hydration status in acute ischemic stroke patients with dysphagia. A retrospective chart review was completed on 67 ischemic stroke patients who participated in a prior study of nutrition and hydration status during acute care. Prior results indicated that patients with dysphagia demonstrated elevated BUN/Cr compared to non-dysphagia cases during acute care and that BUN/Cr increased selectively in dysphagic patients. This chart review evaluated clinical variables potentially impacting hydration status: diuretics, parenteral fluids, tube feeding, oral diet, and nonoral (NPO) status. Exposure to any variable and number of days of exposure to each variable were examined. Dysphagia cases demonstrated significantly more NPO days, tube fed days, and parenteral fluid days, but not oral fed days, or days on diuretics. BUN/Cr values at discharge were not associated with NPO days, parenteral fluid days, oral fed days, or days on diuretics. Patients on modified solid diets had significantly higher mean BUN/Cr values at discharge (27.12 vs. 17.23) as did tube fed patients (28.94 vs. 18.66). No difference was noted between these subgroups at baseline (regular diet vs. modified solids diets). Any modification of solid diets (31.11 vs. 17.23) or thickened liquids (28.50 vs. 17.81) resulted in significantly elevated BUN/Cr values at discharge. Liquid or diet modifications prescribed for acute stroke patients with dysphagia may impair hydration status in these patients.

The hydration status of young female elite soccer players during an official tournament.

PubMed

Chapelle, Laurent; Tassignon, Bruno; Aerenhouts, Dirk; Mullie, Patrick; Clarys, Peter

2017-09-01

The hydration status of elite female soccer players is a concern, especially during high-volume training periods or tournaments. Furthermore, scientific literature on this topic is scarce to non-existent. Therefore, the primary aim of this study was to evaluate the hydration status in elite youth female soccer players during an official tournament. The secondary aim was to identify a possible relationship between pre-training hydration status and fluid intake. Eighteen players were followed during eight consecutive days. Urine specific gravity was used to assess hydration status. Body weight was monitored before and after every training and match, whilst individual fluid intake was only registered during training. The players were informed about their hydration status on day 5. On days 1 to 4, the percentage of players who were at least minimally hypohydrated ranged between 44% and 78%. On day 5 (rest day), all the players were at least minimally hypohydrated. After the information session on day 5, the relative number of euhydrated players increased to 89% on both day 6 (training day) and day 7 (match day). On the final day (rest day), all players were either minimally hypohydrated or hypohydrated. Furthermore, a moderate and significant negative correlation (r=-0.44; N.=54; P=0.01) was found between fluid intake during and USG value before the training sessions. The data illustrates that the hydration status of this population of elite youth female soccer players may be suboptimal and is of substantial concern on rest days during this tournament under temperate conditions. Receiving personal advice about rehydration seems to have a positive effect.

Chloral hydrate in intractable status epilepticus.

PubMed

Lampl, Y; Eshel, Y; Gilad, R; Sarova-Pinchas, I

1990-06-01

Five adult patients were admitted to the neurological department in a state of status epilepticus. All were treated unsuccessfully with IV diazepam and diphenylhydantoin. Administration of sodium valporate or phenobarbital also was ineffective. However, after treatment with intrarectal chloral hydrate, all seizures ceased. The excellent effect of this drug was proved both clinically and electrodiagnostically. Discussed is the possibility of using chloral hydrate to treat patients with status epilepticus in whom conventional treatment has failed.

Acoustical Method of Whole-Body Hydration Status Monitoring.

PubMed

Sarvazyan, A P; Tsyuryupa, S N; Calhoun, M; Utter, A

2016-07-01

An acoustical handheld hydration monitor (HM) for assessing the water balance of the human body was developed. Dehydration is a critical public health problem. Many elderly over age of 65 are particularly vulnerable as are infants and young children. Given that dehydration is both preventable and reversible, the need for an easy-to-perform method for the detection of water imbalance is of the utmost clinical importance. The HM is based on an experimental fact that ultrasound velocity in muscle is a linear function of water content and can be referenced to the hydration status of the body. Studies on the validity of HM for the assessment of whole-body hydration status were conducted in the Appalachian State University, USA, on healthy young adults and on elderly subjects residing at an assisted living facility. The HM was able to track changes in total body water during periods of acute dehydration and rehydration in athletes and day-to-day and diurnal variability of hydration in elderly. Results of human studies indicate that HM has a potential to become an efficient tool for detecting abnormal changes in the body hydration status.

Acoustical method of whole-body hydration status monitoring

NASA Astrophysics Data System (ADS)

Sarvazyan, A. P.; Tsyuryupa, S. N.; Calhoun, M.; Utter, A.

2016-07-01

An acoustical handheld hydration monitor (HM) for assessing the water balance of the human body was developed. Dehydration is a critical public health problem. Many elderly over age of 65 are particularly vulnerable as are infants and young children. Given that dehydration is both preventable and reversible, the need for an easy-to-perform method for the detection of water imbalance is of the utmost clinical importance. The HM is based on an experimental fact that ultrasound velocity in muscle is a linear function of water content and can be referenced to the hydration status of the body. Studies on the validity of HM for the assessment of whole-body hydration status were conducted in the Appalachian State University, USA, on healthy young adults and on elderly subjects residing at an assisted living facility. The HM was able to track changes in total body water during periods of acute dehydration and rehydration in athletes and day-to-day and diurnal variability of hydration in elderly. Results of human studies indicate that HM has a potential to become an efficient tool for detecting abnormal changes in the body hydration status.

Hydration status of Air Force military basic trainees after implementation of the back-mounted hydration system.

PubMed

Fogt, Donovan L; Brosch, Lorie C; Dacey, Danny C; Kalns, John E; Ketchum, Norma S; Rohrbeck, Patricia; Venuto, Margaret M; Tchandja, Juste B; Bunning, Mike L

2009-08-01

The Air Force makes an extraordinary effort to prevent heat-related illnesses associated with basic military training (BMT) in south Texas. However, inadequate hydration can still contribute to lost training time and qualified trainees leaving military service without completing BMT. The purpose of the present study was to determine whether equipping BMTs with back-mounted hydration systems (BM) is better than the standard-issue (SI) canteens with respect to hydration status. Male BMTs were randomly assigned to either BM (n = 40) or SI (n = 38) groups. Baseline values were assessed at week 0 before any physical readiness training (PRT). Subsequent data collection took place in the a.m. before PRT and in the p.m. before dinner the first 3 weeks, and during the 5 weeks of training. BMT total body water (TBW) and body composition were assessed by bioelectrical impedance. Saliva osmolality and total protein concentration were also determined. Hydration status increased daily in BM and SI and was well maintained over the duration of BMT. A significant hydration effect (p < 0.05) was observed for average daily increases in TBW and body weight with BM gaining more compared to SI. Average a.m. TBW was 0.3-0.8 L greater in SI versus BM (p < 0.05). Our findings demonstrate that adequate hydration status is maintained during Air Force BMT in a hot environment using either hydration mode and therefore do not support widespread issuance of the BM system on the premise of improved hydration during USAF BMT military training.

Aluminum-induced dreierketten chain cross-links increase the mechanical properties of nanocrystalline calcium aluminosilicate hydrate

DOE PAGES

Geng, Guoqing; Myers, Rupert J.; Li, Jiaqi; ...

2017-03-10

The incorporation of Al and increased curing temperature promotes the crystallization and cross-linking of calcium (alumino)silicate hydrate (C-(A-)S-H), which is the primary binding phase in most contemporary concrete materials. However, the influence of Al-induced structural changes on the mechanical properties at atomistic scale is not well understood. Herein, synchrotron radiation-based high-pressure X-ray diffraction is used to quantify the influence of dreierketten chain cross-linking on the anisotropic mechanical behavior of C-(A-)S-H. We show that the ab-planar stiffness is independent of dreierketten chain defects, e.g. vacancies in bridging tetrahedra sites and Al for Si substitution. The c-axis of non-cross-linked C-(A-)S-H is moremore » deformable due to the softer interlayer opening but stiffens with decreased spacing and/or increased zeolitic water and Ca 2+ of the interlayer. Dreierketten chain cross-links act as ‘columns’ to resist compression, thus increasing the bulk modulus of C-(A-)S-H. We provide the first experimental evidence on the influence of the Al-induced atomistic configurational change on the mechanical properties of C-(A-)S-H. Our work advances the fundamental knowledge of C-(A-)S-H on the lowest level of its hierarchical structure, and thus can impact the way that innovative C-(A-)S-H-based cementitious materials are developed using a ‘bottom-up’ approach.« less

Aluminum-induced dreierketten chain cross-links increase the mechanical properties of nanocrystalline calcium aluminosilicate hydrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geng, Guoqing; Myers, Rupert J.; Li, Jiaqi

The incorporation of Al and increased curing temperature promotes the crystallization and cross-linking of calcium (alumino)silicate hydrate (C-(A-)S-H), which is the primary binding phase in most contemporary concrete materials. However, the influence of Al-induced structural changes on the mechanical properties at atomistic scale is not well understood. Herein, synchrotron radiation-based high-pressure X-ray diffraction is used to quantify the influence of dreierketten chain cross-linking on the anisotropic mechanical behavior of C-(A-)S-H. We show that the ab-planar stiffness is independent of dreierketten chain defects, e.g. vacancies in bridging tetrahedra sites and Al for Si substitution. The c-axis of non-cross-linked C-(A-)S-H is moremore » deformable due to the softer interlayer opening but stiffens with decreased spacing and/or increased zeolitic water and Ca 2+ of the interlayer. Dreierketten chain cross-links act as ‘columns’ to resist compression, thus increasing the bulk modulus of C-(A-)S-H. We provide the first experimental evidence on the influence of the Al-induced atomistic configurational change on the mechanical properties of C-(A-)S-H. Our work advances the fundamental knowledge of C-(A-)S-H on the lowest level of its hierarchical structure, and thus can impact the way that innovative C-(A-)S-H-based cementitious materials are developed using a ‘bottom-up’ approach.« less

Towards bio-silicon interfaces: Formation of an ultra-thin self-hydrated artificial membrane composed of dipalmitoylphosphatidylcholine (DPPC) and chitosan deposited in high vacuum from the gas-phase

NASA Astrophysics Data System (ADS)

Retamal, María J.; Cisternas, Marcelo A.; Gutierrez-Maldonado, Sebastian E.; Perez-Acle, Tomas; Seifert, Birger; Busch, Mark; Huber, Patrick; Volkmann, Ulrich G.

2014-09-01

The recent combination of nanoscale developments with biological molecules for biotechnological research has opened a wide field related to the area of biosensors. In the last years, device manufacturing for medical applications adapted the so-called bottom-up approach, from nanostructures to larger devices. Preparation and characterization of artificial biological membranes is a necessary step for the formation of nano-devices or sensors. In this paper, we describe the formation and characterization of a phospholipid bilayer (dipalmitoylphosphatidylcholine, DPPC) on a mattress of a polysaccharide (Chitosan) that keeps the membrane hydrated. The deposition of Chitosan (˜25 Å) and DPPC (˜60 Å) was performed from the gas phase in high vacuum onto a substrate of Si(100) covered with its native oxide layer. The layer thickness was controlled in situ using Very High Resolution Ellipsometry (VHRE). Raman spectroscopy studies show that neither Chitosan nor DPPC molecules decompose during evaporation. With VHRE and Atomic Force Microscopy we have been able to detect phase transitions in the membrane. The presence of the Chitosan interlayer as a water reservoir is essential for both DPPC bilayer formation and stability, favoring the appearance of phase transitions. Our experiments show that the proposed sample preparation from the gas phase is reproducible and provides a natural environment for the DPPC bilayer. In future work, different Chitosan thicknesses should be studied to achieve a complete and homogeneous interlayer.

Mechanisms associated with the high adsorption of dibenzo-p-dioxin from water by smectite clays.

PubMed

Liu, Cun; Li, Hui; Teppen, Brian J; Johnston, Cliff T; Boyd, Stephen A

2009-04-15

Clay minerals may be an important unrecognized sorptive phase for dioxins in soils and clay deposits. Smectites, especially Cs-saponite, effectively adsorbed dibenzo-p-dioxin (DD) from water, reaching 0.8% (wt/wt). Adsorption was promoted by exchangeable cations with low hydration energies, and negative charge in the smectite arising from the tetrahedral siloxane sheets. X-ray diffraction measurements revealed that as DD loading increased to > or =8000 mg/kg the clay basal spacing increased abruptly from 12.3 to 15.2 A demonstrating DD intercalation. The 12.3 A spacing provides an interlayer distance that closely matches the molecular thickness of DD. In this configuration DD is essentially dehydrated as it interacts with the opposing hydrophobic siloxane sheets and with coplanar Cs+ via one of the dioxin ring oxygens. Ab initio calculations suggest that geometrical structures form at higher loadings in which intercalated DD molecules adopt a butterfly geometry sandwiched between dehydrated interlayer Cs+ and the siloxane surface, consistent with the 15.2 A spacing, wherein Cs+ interacts with dioxin ring oxygens and benzene ring pi-electrons. Fourier transformation infrared measurements confirm that adsorbed DD is present in orientations that are not parallel with the interlayer planar siloxane surfaces of smectite.

Docking 90Sr radionuclide in cement: An atomistic modeling study

NASA Astrophysics Data System (ADS)

Youssef, Mostafa; Pellenq, Roland J.-M.; Yildiz, Bilge

Cementitious materials are considered to be a waste form for the ultimate disposal of radioactive materials in geological repositories. We investigated by means of atomistic simulations the encapsulation of strontium-90, an important radionuclide, in calcium-silicate-hydrate (C-S-H) and its crystalline analog, the 9 Å-tobermorite. C-S-H is the major binding phase of cement. Strontium was shown to energetically favor substituting calcium in the interlayer sites in C-S-H and 9 Å-tobermorite with the trend more pronounced in the latter. The integrity of the silicate chains in both cementitious waste forms were not affected by strontium substitution within the time span of molecular dynamics simulation. Finally, we observed a limited degradation of the mechanical properties in the strontium-containing cementitious waste form with the increasing strontium concentration. These results suggest the cement hydrate as a good candidate for immobilizing radioactive strontium.

Role of interatomic bonding in the mechanical anisotropy and interlayer cohesion of CSH crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dharmawardhana, C.C.; Misra, A.; Aryal, S.

2013-10-15

Atomic scale properties of calcium silicate hydrate (CSH), the main binding phase of hardened Portland cement, are not well understood. Over a century of intense research has identified almost 50 different crystalline CSH minerals which are mainly categorized by their Ca/Si ratio. The electronic structure and interatomic bonding in four major CSH crystalline phases with structures close to those found in hardened cement are investigated via ab initio methods. Our result reveals the critical role of hydrogen bonding and importance of specifying precise locations for water molecules. Quantitative analysis of contributions from different bond types to the overall cohesion showsmore » that while the Si-O covalent bonds dominate, the hydrogen bonding and Ca-O bonding are also very significant. Calculated results reveal the correlation between bond topology and interlayer cohesion. The overall bond order density (BOD) is found to be a more critical measure than the Ca/Si ratio in classifying different CSH crystals.« less

Radiocesium interaction with clay minerals: Theory and simulation advances Post-Fukushima.

PubMed

Okumura, Masahiko; Kerisit, Sebastien; Bourg, Ian C; Lammers, Laura N; Ikeda, Takashi; Sassi, Michel; Rosso, Kevin M; Machida, Masahiko

2018-04-14

Insights at the microscopic level of the process of radiocesium adsorption and interaction with clay mineral particles have improved substantially over the past several years, triggered by pressing social issues such as management of huge amounts of waste soil accumulated after the Fukushima Dai-ichi nuclear power plant accident. In particular, computer-based molecular modeling supported by advanced hardware and algorithms has proven to be a powerful approach. Its application can now generally encompass the full complexity of clay particle adsorption sites from basal surfaces to interlayers with inserted water molecules, to edges including fresh and weathered frayed ones. On the other hand, its methodological schemes are now varied from traditional force-field molecular dynamics on large-scale realizations composed of many thousands of atoms including water molecules to first-principles methods on smaller models in rather exacting fashion. In this article, we overview new understanding enabled by simulations across methodological variations, focusing on recent insights that connect with experimental observations, namely: 1) the energy scale for cesium adsorption on the basal surface, 2) progress in understanding the structure of clay edges, which is difficult to probe experimentally, 3) cesium adsorption properties at hydrated interlayer sites, 4) the importance of the size relationship between the ionic radius of cesium and the interlayer distance at frayed edge sites, 5) the migration of cesium into deep interlayer sites, and 6) the effects of nuclear decay of radiocesium. Key experimental observations that motivate these simulation advances are also summarized. Furthermore, some directions toward future solutions of waste soil management are discussed based on the obtained microscopic insights. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Radiocesium interaction with clay minerals: Theory and simulation advances Post–Fukushima

DOE PAGES

Okumura, Masahiko; Kerisit, Sebastien; Bourg, Ian C.; ...

2018-03-14

Insights at the microscopic level of the process of radiocesium adsorption and interaction with clay mineral particles have improved substantially over the past several years, triggered by pressing social issues such as management of huge amounts of waste soil accumulated after the Fukushima Dai–ichi nuclear power plant accident. In particular, computer–based molecular modeling supported by advanced hardware and algorithms has proven to be a powerful approach. Its application can now generally encompass the full complexity of clay particle adsorption sites from basal surfaces to interlayers with inserted water molecules, to edges including fresh and weathered frayed ones. On the othermore » hand, its methodological schemes are now varied from traditional force–field molecular dynamics on large–scale realizations composed of many thousands of atoms including water molecules to first–principles methods on smaller models in rather exacting fashion. In this article, we overview new understanding enabled by simulations across methodological variations, focusing on recent insights that connect with experimental observations, namely: 1) the energy scale for cesium adsorption on the basal surface, 2) progress in understanding the structure of clay edges, which is difficult to probe experimentally, 3) cesium adsorption properties at hydrated interlayer sites, 4) the importance of the size relationship between the ionic radius of cesium and the interlayer distance at frayed edge sites, 5) the migration of cesium into deep interlayer sites, and 6) the effects of nuclear decay of radiocesium. Key experimental observations that motivate these simulation advances are also summarized. Furthermore, some directions toward future solutions of waste soil management are discussed based on the obtained microscopic insights.« less

Radiocesium interaction with clay minerals: Theory and simulation advances Post–Fukushima

DOE Office of Scientific and Technical Information (OSTI.GOV)

Okumura, Masahiko; Kerisit, Sebastien; Bourg, Ian C.

Insights at the microscopic level of the process of radiocesium adsorption and interaction with clay mineral particles have improved substantially over the past several years, triggered by pressing social issues such as management of huge amounts of waste soil accumulated after the Fukushima Dai–ichi nuclear power plant accident. In particular, computer–based molecular modeling supported by advanced hardware and algorithms has proven to be a powerful approach. Its application can now generally encompass the full complexity of clay particle adsorption sites from basal surfaces to interlayers with inserted water molecules, to edges including fresh and weathered frayed ones. On the othermore » hand, its methodological schemes are now varied from traditional force–field molecular dynamics on large–scale realizations composed of many thousands of atoms including water molecules to first–principles methods on smaller models in rather exacting fashion. In this article, we overview new understanding enabled by simulations across methodological variations, focusing on recent insights that connect with experimental observations, namely: 1) the energy scale for cesium adsorption on the basal surface, 2) progress in understanding the structure of clay edges, which is difficult to probe experimentally, 3) cesium adsorption properties at hydrated interlayer sites, 4) the importance of the size relationship between the ionic radius of cesium and the interlayer distance at frayed edge sites, 5) the migration of cesium into deep interlayer sites, and 6) the effects of nuclear decay of radiocesium. Key experimental observations that motivate these simulation advances are also summarized. Furthermore, some directions toward future solutions of waste soil management are discussed based on the obtained microscopic insights.« less

Measured and perceived indices of fluid balance in professional athletes. The use and impact of hydration assessment strategies.

PubMed

Love, T D; Baker, D F; Healey, P; Black, K E

2018-04-01

To determine athletes perceived and measured indices of fluid balance during training and the influence of hydration strategy use on these parameters. Thirty-three professional rugby union players completed a 120 minute training session in hot conditions (35°C, 40% relative humidity). Pre-training hydration status, sweat loss, fluid intake and changes in body mass (BM) were obtained. The use of hydration assessment techniques and players perceptions of fluid intake and sweat loss were obtained via a questionnaire. The majority of players (78%) used urine colour to determine pre-training hydration status but the use of hydration assessment techniques did not influence pre-training hydration status (1.025 ± 0.005 vs. 1.023 ± 0.013 g . ml -1 , P = .811). Players underestimated sweat loss (73 ± 17%) to a greater extent than fluid intake (37 ± 28%) which resulted in players perceiving they were in positive fluid balance (0.5 ± 0.8% BM) rather than the measured negative fluid balance (-1.0 ± 0.7% BM). Forty-eight percent of players used hydration monitoring strategies during exercise but no player used changes in BM to help guide fluid replacement. Players have difficulty perceiving fluid intake and sweat loss during training. However, the use of hydration monitoring techniques did not affect fluid balance before or during training.

Investigation of Wyoming Bentonite Hydration in Dry to Water-Saturated Supercritical CH4 and CH4/CO2 Mixtures: Implications for CO2-Enhanced Gas Production

NASA Astrophysics Data System (ADS)

Loring, J.

2015-12-01

Injection of CO2 into low permeability shale formations leads to additional gas recovery and reduces the flux of CO2 into the atmosphere, thus combining a strong economic incentive with a permanent storage option for CO2. Reduced formation transmissivity due to clay swelling is a concern in CO2-enhanced gas production. Clay minerals partly determine the physical (i.e. permeability, brittleness) and certain chemical properties (i.e. wetting ability, gas adsorption) of shales, and montmorillonites are of particular interest because they swell by the uptake of species in their interlayer. In this study, the hydration and expansion of Na-, Cs-, and NH4+-saturated montmorillonite (Na-, Cs-, and NH4-SWy-2) in high-pressure (90 bar) and moderate temperature (50 °C) methane, carbon dioxide, and CO2/CH4 mixtures (3 and 25 mole% CO2) were investigated using in situ IR spectroscopic titrations, in situ XRD, in situ MAS-NMR, and ab initio electronic structure calculations. The overarching goal was to better understand the hydration/expansion behavior of Na-SWy-2 in CO2/CH4 fluid mixtures by comparison to Cs-, and NH4+-saturated clays. Specific aims were to (1) determine if CH4 intercalates the clays, (2) probe the effects of increasing dissolved CO2 and H2O concentrations, and (3) understand the role of cation solvation by H2O and/or CO2. In pure CH4, no evidence of CH4 intercalation was detected by IR for any of the clays. Similarly, no measurable changes to the basal spacing were observed by XRD in the presence of pure CH4. However, when dry Cs- and NH4-SWy-2 were exposed to dry fluids containing CO2, IR showed maximum CO2 penetrated the interlayer, XRD indicated the clays expanded, and NMR showed evidence for cation solvation by CO2, in line with theoretical predictions. IR titration of these clays with water showed sorbed H2O concentrations decreased with increasing dissolved CO2, suggesting competition for interlayer residency by CO2 and H2O. For Na-SWy-2, on the other hand, CO2 intercalated the clay and was at a maximum only after a minimum sorbed H2O was achieved. Further increases in sorbed H2O led to displacement of intercalated CO2. These findings demonstrate that complicated H2O and CO2 intercalation processes could lead to permeability changes that directly impact methane transmissivity in shales.

Performing Mineral Hydration Experiments in the CheMin Diffractometer on Mars

NASA Technical Reports Server (NTRS)

Vaniman, D. T.; Yen, A. S.; Rampe, E. B.; Blake, D. F.; Chipera, S. J.; Morookian, J. M.; Ming, D. W.; Bristow, T. F.; Morris, R. V.; Geller, R.;

Double cross-polarization MAS NMR in the assignment of abundant-spin resonances: ¹⁹F-{²⁹Si}-¹⁹F FBCP/MAS NMR of fluoride ions incorporated in calcium silicate hydrate (C-S-H) phases.

PubMed

Tran, Thuan T; Bildsøe, Henrik; Jakobsen, Hans J; Skibsted, Jørgen

2012-08-01

A new version of the double cross-polarization MAS NMR experiment, which transfers polarization Forth and Back (FBCP) between high- and low-γ spin nuclei, is presented. The pulse sequence is demonstrated by ¹⁹F-{²⁹Si}-¹⁹F and ¹⁹F-{¹³C}-¹⁹F FBCP NMR spectra of a mixture of cuspidine (Ca₄Si₂O₇F₂) and Teflon (-CF₂-)(n). The experiment is useful for assignment of the high-γ spin resonances, as demonstrated by ¹⁹F-{²⁹Si}-¹⁹F FBCP NMR of a fluoride-containing calcium-silicate-hydrate (C-S-H) phase, where the ¹⁹F resonance from fluoride ions incorporated in the interlayer structure of the C-S-H phase is identified. Copyright © 2012 Elsevier Inc. All rights reserved.

Molecular Level Investigation of CH 4 and CO 2 Adsorption in Hydrated Calcium–Montmorillonite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Mal-Soon; McGrail, B. Peter; Rousseau, Roger

2017-11-17

We have studied the mechanism of intercalation and methane adsorption from a H2O/CH4/CO2 mixture on a prototypical shale component, Ca-montmorillonite. We employed ab initio molecular dynamics simulations at 323 K and 90 bar to obtain molecular level information of adsorption energetics, speciation, and structural and thermodynamic properties. Interaction of CH4 with surface Lewis acidic sites (Ca2+, surface OH) results in large induced dipoles (~1 D) that lead to relatively strong adsorption energies that level off once a full CH4 layer is formed. Intercalated CH4, also exhibits induced dipoles at low hydration levels, when the interaction with Ca2+ cations are lessmore » hindered. CO2 displaces CH4 in the coordination sphere of the cations (in the interlayer) or in the surface, thereby driving CH4 extraction. Our simulations indicate that there is a Goldilocks pressure range (~60-100 bar) where scCO2 –facilitated CH4 extraction will be maximized.« less

In Situ Molecular Spectroscopic Evidence for CO2 Intercalation into Montmorillonite in Supercritical Carbon Dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loring, John S.; Schaef, Herbert T.; Turcu, Romulus VF

2012-04-25

The interaction of anhydrous supercritical CO2 (scCO2) with both kaolinite and ~1W (i.e. close to but less than one layer of hydration) calcium-saturated montmorillonite was investigated under conditions relevant to geologic carbon sequestration (50 °C and 90 bar). The CO2 molecular environment was probed in situ using a combination of three novel high-pressure techniques: X-ray diffraction, magic angle spinning nuclear magnetic resonance spectroscopy and attenuated total reflection infrared spectroscopy. We report the first direct evidence that the expansion of montmorillonite under scCO2 conditions is due to CO2 migration into the interlayer. Intercalated CO2 molecules are rotationally constrained and do notmore » appear to react with waters to form bicarbonate or carbonic acid. In contrast, CO2 does not intercalate into kaolinite. The findings show that predicting the seal integrity of caprock will have complex dependence on clay mineralogy and hydration state.« less

Validation of beverage intake methods vs. hydration biomarkers; a short review.

PubMed

Nissensohn, Mariela; Ruano, Cristina; Serra-Majem, Lluis

2013-11-01

Fluid intake is difficult to monitor. Biomarkers of beverage intake are able to assess dietary intake/hydration status without the bias of self-reported dietary intake errors and also the intra-individual variability. Various markers have been proposed to assess hydration, however, to date; there is a lack of universally accepted biomarker that reflects changes of hydration status in response to changes in beverage intake. We conduct a review to find out the questionnaires of beverage intake available in the scientific literature to assess beverage intake and hydration status and their validation against hydration biomarkers. A scientific literature search was conducted. Only two articles were selected, in which, two different beverage intake questionnaires designed to capture the usual beverage intake were validated against Urine Specific Gravidity biomarker (Usg). Water balance questionnaire (WBQ) reported no correlations in the first study and the Beverage Intake Questionnaire (BEVQ), a quantitative Food frequency questionnaire (FFQ) in the second study, also found a negative correlation. FFQ appears to measure better beverage intake than WBQ when compared with biomarkers. However, the WBQ seems to be a more complete method to evaluate the hydration balance of a given population. Further research is needed to understand the meaning of the different correlations between intake estimates and biomarkers of beverage in distinct population groups and environments. Copyright AULA MEDICA EDICIONES 2013. Published by AULA MEDICA. All rights reserved.

Hydration status, sweat rates, and rehydration education of youth football campers.

PubMed

McDermott, Brendon P; Casa, Douglas J; Yeargin, Susan W; Ganio, Matthew S; Lopez, Rebecca M; Mooradian, Elizabeth A

2009-11-01

Previous field research has not identified sweat rates (SR), fluid consumption (FC), or the efficacy of an educational intervention (EI) for youth during football camp. To measure hydration status and rehydration performance and examine EL using these data. Observational with EI randomized comparison. Thirty-three boys (mean +/- SD: 12 +/- 2 y, 52.9 +/- 13.6 kg, 156 +/- 12 cm) volunteered during a 5-d camp with 3 (-2-h) sessions per day (WBGT: 25.6 +/- 0.5 degrees C). Hydration status, SR, and FC. Urine osmolality averaged 796 +/- 293 mOsm/L for days 2-5. Game SR (1.30 +/- 0.57 L/h) was significantly greater than practice SR (0.65 +/- 0.35 L/h; P = .002). Subjects dehydrated during free time but matched fluid losses with FC (0.76 +/- 0.29 L/h) during football activities. Subjects arrived at camp hypohydrated and maintained this condition. They matched FC and SR during, but dehydrated when not playing, football. This may impair recovery and subsequent performance. Hydration EI seemed to have a positive influence on hydration practices.

Aqueous solubility diagrams for cementitious waste stabilization systems. 3. Mechanism of zinc immobilizaton by calcium silicate hydrate.

PubMed

Tommaseo, C E; Kersten, M

2002-07-01

Zinc oxide was added during hydration of alite (C3S) as an analogue for solidification/stabilization by cement of metal-bearing hazardous waste. Curing of samples was stopped at various intervals between 8 h and 100 d, and the reaction products were analyzed by both X-ray diffraction (XRD) and X-ray absorption spectroscopy (EXAFS at Zn, Ca, and Si K-edges). Calcium zincate hydrate (CaZn2(OH)6 x 2H2O) initially formed together with calcium silicate hydrate (CSH) vanishes from X-ray diffractograms after 14 d, and no other crystalline Zn-bearing phase could be detected thereafter. EXAFS Zn K-edge data analysis reveals that Zn(O,OH)4 tetrahedra continue to determine the first shell coordination. However, a new Zn-Si bond appears in the second coordination shell as indicated by both Zn K-edge and Si K-edge EXAFS. Together with the Ca-Zn and Ca-Ca shells derived from the Ca K-edge EXAFS spectra, a structural model for the site occupation of Zn in CSH is proposed, whereby the Zn(O,OH)4 tetrahedra are bound in layer rather than interlayer positions substituting for the silicate bridging tetrahedra and/or at terminal silicate chain sites. This structural model enables ultimately the formulation of a thermodyamic Lippmann model to predict the aqueous solubility of Zn in solid solution with a CSH phase of a Ca/Si ratio fixed to unity.

Multi-channel electrical impedance tomography for regional tissue hydration monitoring.

PubMed

Chen, Xiaohui; Kao, Tzu-Jen; Ashe, Jeffrey M; Boverman, Gregory; Sabatini, James E; Davenport, David M

2014-06-01

Poor assessment of hydration status during hemodialysis can lead to under- or over-hydration in patients with consequences of increased morbidity and mortality. In current practice, fluid management is largely based on clinical assessments to estimate dry weight (normal hydration body weight). However, hemodialysis patients usually have co-morbidities that can make the signs of fluid status ambiguous. Therefore, achieving normal hydration status remains a major challenge for hemodialysis therapy. Electrical impedance technology has emerged as a promising method for hydration monitoring due to its non-invasive nature, low cost and ease-of-use. Conventional electrical impedance-based hydration monitoring systems employ single-channel current excitation (either 2-electrode or 4-electrode methods) to perturb and extract averaged impedance from bulk tissue and use generalized models from large populations to derive hydration estimates. In the present study, a prototype, single-frequency electrical impedance tomography (EIT) system with simultaneous multi-channel current excitation was used to enable regional hydration change detection. We demonstrated the capability to detect a difference in daily impedance change between left leg and right leg in healthy human subjects, who wore a compression sock only on one leg to reduce daily gravitational fluid accumulation. The impedance difference corresponded well with the difference of lower leg volume change between left leg and right leg measured by volumetry, which on average is ~35 ml, accounting for 0.7% of the lower leg volume. We have demonstrated the feasibility of using multi-channel EIT to extract hydration information in different tissue layers with minimal skin interference. Our simultaneous, multi-channel current excitation approach provides an effective method to separate electrode contact impedance and skin condition artifacts from hydration signals. The prototype system has the potential to be used in clinical settings for helping optimize patient fluid management during hemodialysis as well as for home monitoring of patients with congestive heart failure, chronic kidney disease, diabetes and other diseases with peripheral edema symptoms.

Diagnostic Performance of Afternoon Urine Osmolality to Assess Optimal Hydration Status in an Adult Healthy Population.

PubMed

Hustrini, Ni Made; Siregar, Parlindungan; Nainggolan, Ginova; Harimurti, Kuntjoro

2017-04-01

optimal hydration represents adequate total daily fluid intake to compensate for daily water losses, ensure adequate urine output to reduce the risk of urolithiasis and renal function decline, and also avoid the production of arginine vasopressin (AVP). Twenty-four-hour urine osmolality has been used to assess hydration status, but it is challenging because of the possibility of spilling urine and limitation of daily activities. This study is aimed to determine the performance of the afternoon urine osmolality to assess the optimal hydration status compared with 24-hour urine osmolality. a cross sectional study was conducted on healthy employees aged 18-59 years at Universitas Indonesia Medical Faculty/Cipto Mangunkusumo Hospital, with consecutive sampling method. The ROC curve was analyzed to obtain the optimal cut off point and the accuracy of the afternoon urine osmolality in assessing the optimal hydration status. between August-September 2016 there were 120 subjects (73.8% female, median age 32 years) who met the study criteria with a median 24-hour urine osmolality 463.5 (95% CI, 136-1427) mOsm/kg H2O and median afternoon urine osmolality 513 (95% CI, 73-1267). We found moderate correlation (r=0.59; p<0.001) between afternoon urine osmolality and a 24-hour urine osmolality. Using ROC curve, the AUC value was 0.792 (95% CI, 0.708-0.875) with the cut off 528 mOsm/kg H2O. To assess the optimal hydration status, the afternoon urine osmolality had the sensitivity of 0.7 (95% CI, 0.585-0.795) and the specificity of 0.76 (95% CI, 0.626-0.857), Likelihood Ratio (LR) (+) 2.917 (95% CI, 1.74-4.889) and LR (-) 0.395 (95% CI, 0.267-0.583). afternoon urine osmolality can be used as a diagnostic tool to assess the optimal hydration status in healthy population with cut off 528 mOsm/kg H2O, sensitivity of 0.7, and specificity of 0.76.

Microstructural Response of Variably Hydrated Ca-Rich Montmorillonite to Supercritical CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Mal Soon; McGrail, B. Peter; Glezakou, Vassiliki Alexandra

2014-08-05

We report on ab initio molecular dynamics simulations of Ca-rich montmorillonite systems, in different hydration states in the presence of supercritical CO2. Analysis of the molecular trajectories provides estimates of the relative H2O:CO2 ratio per interspatial cation. The vibrational density of states in direct comparison with dipole moment derived IR spectra for these systems provide unique signatures that can used to follow molecular transformation. In a co-sequestration scenario, these signatures could be used to identify the chemical state and fate of Sulfur compounds. Interpretation of CO2 asymmetric stretch shift is given based on a detailed analysis of scCO2 structure andmore » intermolecular interactions of the intercalated species. Based on our simulations, smectites with higher charge interlayer cations at sub-single to single hydration states should be more efficient in capturing CO2, while maintaining caprock integrity. This research would not have been possible without the support of the office of Fossil Energy, Department of Energy. The computational resources were made available through a user proposal of the EMSL User facility, a national scientific user facility sponsored by the Department of Energy's Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory.« less

Investigation of Wyoming Bentonite Hydration in Dry to Water-Saturated Supercritical CH4 and CH4/CO2 Mixtures: Implications for CO2-Enhanced Gas Production

NASA Astrophysics Data System (ADS)

Loring, J.; Thompson, C.; Ilton, E. S.; McGrail, B. P.; Schaef, T.

2014-12-01

Injection of CO2 into low permeability shale formations leads to additional gas recovery and reduces the flux of CO2 into the atmosphere, thus combining a strong economic incentive with a permanent storage option for CO2. Reduced formation transmissivity due to clay swelling is a concern in CO2 -enhanced gas production. Clay minerals partly determine the physical (i.e. permeability, brittleness) and certain chemical properties (i.e. wetting ability, gas adsorption) of shales, and montmorillonites are of particular interest because they swell by the uptake of species in their interlayer. In this study, the hydration and expansion of a Na-saturated montmorillonite (Na-SWy-2) in high-pressure (90 bar) and moderate temperature (50 °C) methane and mixtures of methane and carbon dioxide were investigated usingCH4 IR spectroscopic titrations andCH4 XRD. The goals were to (1) determine if the hydration/expansion behavior of the clay in supercritical methane is different than in supercritical CO2, (2) determine if methane intercalates the clay, and (3) probe the effects of increasing CO2 concentrations. IR spectra were collected as Na-SWy-2 was titrated with water under several fluid exposures: pure methane, 25, 50, and 75 mole% CO2 in methane, and pure CO2. ComplementaryCH4 XRD experiments were conducted in the same fluids at discrete dissolved water concentrations to measure the d001 values of the clay and thus its volume change on hydration and CH4 and/or CO2 intercalation. In pure methane, no direct evidence of CH4 intercalation was detected in CH bending or stretching regions of the IR spectra. Similarly, in situ XRD indicated the montmorillonite structure was stable in the presence of CH4 and no measurable changes to the basal spacing were observed. However, under low water conditions where the montmorillonite structure was partially expanded (~sub 1W), the IR data indicated a rapid intercalation of CO2 into the interlayer, even with fluid mixtures containing the lowest concentrations of CO2. Likewise,CH4 XRD showed indirect evidence of CO2 intercalation from an increase in the basal spacing from 11.8 to 12.3 under identical conditions. These findings demonstrate that water and CO2 intercalation processes could lead to permeability changes that directly impact methane transmissivity in shales.

Toward production from gas hydrates: Current status, assessment of resources, and simulation-based evaluation of technology and potential

USGS Publications Warehouse

Moridis, G.J.; Collett, T.S.; Boswell, R.; Kurihara, M.; Reagan, M.T.; Koh, C.; Sloan, E.D.

2008-01-01

Gas hydrates are a vast energy resource with global distribution in the permafrost and in the oceans. Even if conservative estimates are considered and only a small fraction is recoverable, the sheer size of the resource is so large that it demands evaluation as a potential energy source. In this review paper, we discuss the distribution of natural gas hydrate accumulations, the status of the primary international R&D programs, and the remaining science and technological challenges facing commercialization of production. After a brief examination of gas hydrate accumulations that are well characterized and appear to be models for future development and gas production, we analyze the role of numerical simulation in the assessment of the hydrate production potential, identify the data needs for reliable predictions, evaluate the status of knowledge with regard to these needs, discuss knowledge gaps and their impact, and reach the conclusion that the numerical simulation capabilities are quite advanced and that the related gaps are either not significant or are being addressed. We review the current body of literature relevant to potential productivity from different types of gas hydrate deposits, and determine that there are consistent indications of a large production potential at high rates over long periods from a wide variety of hydrate deposits. Finally, we identify (a) features, conditions, geology and techniques that are desirable in potential production targets, (b) methods to maximize production, and (c) some of the conditions and characteristics that render certain gas hydrate deposits undesirable for production. Copyright 2008, Society of Petroleum Engineers.

Interlayer Water Regulates the Bio-nano Interface of a β-sheet Protein stacking on Graphene

PubMed Central

Lv, Wenping; Xu, Guiju; Zhang, Hongyan; Li, Xin; Liu, Shengju; Niu, Huan; Xu, Dongsheng; Wu, Ren'an

2015-01-01

Using molecular dynamics simulations, we investigated an integrated bio-nano interface consisting of a β-sheet protein stacked onto graphene. We found that the stacking assembly of the model protein on graphene could be controlled by water molecules. The interlayer water filled within interstices of the bio-nano interface could suppress the molecular vibration of surface groups on protein, and could impair the CH···π interaction driving the attraction of the protein and graphene. The intermolecular coupling of interlayer water would be relaxed by the relative motion of protein upon graphene due to the interaction between water and protein surface. This effect reduced the hindrance of the interlayer water against the assembly of protein on graphene, resulting an appropriate adsorption status of protein on graphene with a deep free energy trap. Thereby, the confinement and the relative sliding between protein and graphene, the coupling of protein and water, and the interaction between graphene and water all have involved in the modulation of behaviors of water molecules within the bio-nano interface, governing the hindrance of interlayer water against the protein assembly on hydrophobic graphene. These results provide a deep insight into the fundamental mechanism of protein adsorption onto graphene surface in water. PMID:25557857

Interlayer water regulates the bio-nano interface of a β-sheet protein stacking on graphene.

PubMed

Lv, Wenping; Xu, Guiju; Zhang, Hongyan; Li, Xin; Liu, Shengju; Niu, Huan; Xu, Dongsheng; Wu, Ren'an

2015-01-05

Using molecular dynamics simulations, we investigated an integrated bio-nano interface consisting of a β-sheet protein stacked onto graphene. We found that the stacking assembly of the model protein on graphene could be controlled by water molecules. The interlayer water filled within interstices of the bio-nano interface could suppress the molecular vibration of surface groups on protein, and could impair the CH···π interaction driving the attraction of the protein and graphene. The intermolecular coupling of interlayer water would be relaxed by the relative motion of protein upon graphene due to the interaction between water and protein surface. This effect reduced the hindrance of the interlayer water against the assembly of protein on graphene, resulting an appropriate adsorption status of protein on graphene with a deep free energy trap. Thereby, the confinement and the relative sliding between protein and graphene, the coupling of protein and water, and the interaction between graphene and water all have involved in the modulation of behaviors of water molecules within the bio-nano interface, governing the hindrance of interlayer water against the protein assembly on hydrophobic graphene. These results provide a deep insight into the fundamental mechanism of protein adsorption onto graphene surface in water.

Interlayer Water Regulates the Bio-nano Interface of a β-sheet Protein stacking on Graphene

NASA Astrophysics Data System (ADS)

Lv, Wenping; Xu, Guiju; Zhang, Hongyan; Li, Xin; Liu, Shengju; Niu, Huan; Xu, Dongsheng; Wu, Ren'an

2015-01-01

Using molecular dynamics simulations, we investigated an integrated bio-nano interface consisting of a β-sheet protein stacked onto graphene. We found that the stacking assembly of the model protein on graphene could be controlled by water molecules. The interlayer water filled within interstices of the bio-nano interface could suppress the molecular vibration of surface groups on protein, and could impair the CH...π interaction driving the attraction of the protein and graphene. The intermolecular coupling of interlayer water would be relaxed by the relative motion of protein upon graphene due to the interaction between water and protein surface. This effect reduced the hindrance of the interlayer water against the assembly of protein on graphene, resulting an appropriate adsorption status of protein on graphene with a deep free energy trap. Thereby, the confinement and the relative sliding between protein and graphene, the coupling of protein and water, and the interaction between graphene and water all have involved in the modulation of behaviors of water molecules within the bio-nano interface, governing the hindrance of interlayer water against the protein assembly on hydrophobic graphene. These results provide a deep insight into the fundamental mechanism of protein adsorption onto graphene surface in water.

Comparing the Effects of Alcohol Mixed with Artificially-Sweetened and Carbohydrate Containing Beverages on Breath Alcohol Concentration

ERIC Educational Resources Information Center

Irwin, Christopher; Shum, David; Desbrow, Ben; Leveritt, Michael

2014-01-01

This study investigated the impact of alcohol mixed with artificially sweetened or carbohydrate containing beverages on breath alcohol concentration s (BrAC) under various levels of hydration status. Two groups of males participated in 3 experimental trials where alcohol was consumed under three different levels of hydration status. One group…

Effect of dehydration on the development of collaterals in acute middle cerebral artery occlusion.

PubMed

Chang, S-W; Huang, Y-C; Lin, L-C; Yang, J-T; Weng, H-H; Tsai, Y-H; Lee, T-H

2016-03-01

Recent large series studies have demonstrated that dehydration is common amongst stroke subjects and is associated with poor outcome. However, the effects of hydration status on the development of collaterals have never been discussed. In this study, the hypothesis that hydration status is an important factor for developing collaterals after acute middle cerebral artery (MCA) infarction was tested. Eighty-seven patients with acute infarction due to occlusion of the MCA were enrolled. Two collateral markers, posterior cerebral artery (PCA) laterality and fluid-attenuated inversion recovery hyperintense vessels (HVs) were assessed from magnetic resonance imaging. Dehydration status was defined by a nitrogen to creatinine ratio ≧ of 15. The associations between dehydration status and the development of collaterals were estimated. Sixty-one of 87 patients (70.1%) were identified as dehydrated. The development of PCA laterality and HVs shows a significant difference between dehydrated and euhydrated patients. A serum nitrogen to creatinine ratio <15, diastolic blood pressure and the presence of a dense MCA on computed tomography were significantly associated with the development of PCA laterality. A serum nitrogen to creatinine ratio <15, the initial National Institutes of Health Stroke Scale score, the presence of a dense MCA and calcifications of the internal carotid artery on computed tomography were significantly associated with the development of HVs. Dehydration remained an independent negative predictor for the development of PCA laterality and HVs in the multivariate analysis. Hydration status is associated with the development of collateral flow after acute MCA occlusion. This preliminary study provides an imaging clue that hydration status and early hydration therapy could be important for acute stroke management. © 2016 EAN.

Effect of hydration on some orthostatic and haematological responses to head-up tilt

NASA Technical Reports Server (NTRS)

Harrison, M. H.; Hill, L. C.; Spaul, W. A.; Greenleaf, J. E.

1986-01-01

Experiments were undertaken to determine the effects of hydration status on: (1) orthostatic responses, and on (2) relative changes in intravascular volume and protein content, during 70 deg head-up tilt (HUT). Six men underwent 45 min of HUT, preceded by 45 min supine, first dehydrated, and again 105 min later after rehydration with water. Heart rate was consistently lower following rehydration (p less than 0.01), while supine diastolic pressure was higher (p less than 0.02). Systolic pressure fell during dehydrated HUT (p less than 0.01), but not during rehydrated HUT. Postural haemoconcentration, which was reduced after rehydration (p less than 0.001), was accompanied by a decrease in intravascular albumin content (p less than 0.05). Two subjects experienced severe presyncopal symptoms during dehydrated HUT, but not during rehydrated HUT. Thus, it appears that rehydration after fluid restriction improves orthostatic tolerance. Furthermore, extravascular hydration status may be more important than intravascular hydration status in determining orthostatic tolerance.

Racial/Ethnic and Socioeconomic Disparities in Hydration Status Among US Adults and the Role of Tap Water and Other Beverage Intake

PubMed Central

Gortmaker, Steven L.; Long, Michael W.; Cradock, Angie L.; Kenney, Erica L.

2017-01-01

Objectives. To evaluate whether differences in tap water and other beverage intake explain differences in inadequate hydration among US adults by race/ethnicity and income. Methods. We estimated the prevalence of inadequate hydration (urine osmolality ≥ 800 mOsm/kg) by race/ethnicity and income of 8258 participants aged 20 to 74 years in the 2009 to 2012 National Health and Nutrition Examination Survey. Using multivariable regression models, we estimated associations between demographic variables, tap water intake, and inadequate hydration. Results. The prevalence of inadequate hydration among US adults was 29.5%. Non-Hispanic Blacks (adjusted odds ratio [AOR] = 1.44; 95% confidence interval [CI] = 1.17, 1.76) and Hispanics (AOR = 1.42; 95% CI = 1.21, 1.67) had a higher risk of inadequate hydration than did non-Hispanic Whites. Lower-income adults had a higher risk of inadequate hydration than did higher-income adults (AOR = 1.23; 95% CI = 1.04, 1.45). Differences in tap water intake partially attenuated racial/ethnic differences in hydration status. Differences in total beverage and other fluid intake further attenuated sociodemographic disparities. Conclusions. Racial/ethnic and socioeconomic disparities in inadequate hydration among US adults are related to differences in tap water and other beverage intake. Policy action is needed to ensure equitable access to healthy beverages. PMID:28727528

Racial/Ethnic and Socioeconomic Disparities in Hydration Status Among US Adults and the Role of Tap Water and Other Beverage Intake.

PubMed

Brooks, Carolyn J; Gortmaker, Steven L; Long, Michael W; Cradock, Angie L; Kenney, Erica L

2017-09-01

To evaluate whether differences in tap water and other beverage intake explain differences in inadequate hydration among US adults by race/ethnicity and income. We estimated the prevalence of inadequate hydration (urine osmolality ≥ 800 mOsm/kg) by race/ethnicity and income of 8258 participants aged 20 to 74 years in the 2009 to 2012 National Health and Nutrition Examination Survey. Using multivariable regression models, we estimated associations between demographic variables, tap water intake, and inadequate hydration. The prevalence of inadequate hydration among US adults was 29.5%. Non-Hispanic Blacks (adjusted odds ratio [AOR] = 1.44; 95% confidence interval [CI] = 1.17, 1.76) and Hispanics (AOR = 1.42; 95% CI = 1.21, 1.67) had a higher risk of inadequate hydration than did non-Hispanic Whites. Lower-income adults had a higher risk of inadequate hydration than did higher-income adults (AOR = 1.23; 95% CI = 1.04, 1.45). Differences in tap water intake partially attenuated racial/ethnic differences in hydration status. Differences in total beverage and other fluid intake further attenuated sociodemographic disparities. Racial/ethnic and socioeconomic disparities in inadequate hydration among US adults are related to differences in tap water and other beverage intake. Policy action is needed to ensure equitable access to healthy beverages.

Effect of hydration on plasma volume and endocrine responses to water immersion

NASA Technical Reports Server (NTRS)

Harrison, M. H.; Keil, L. C.; Wade, C. A.; Silver, J. E.; Geelen, G.

1986-01-01

The effect of hydration status on early endocrine responses and on osmotic and intravascular volume changes during immersion was determined in humans undergoing successive periods of dehydration, immersion, rehydration, and immersion. Immersion caused an isotonic expansion of plasma volume, as well as suppression of plasma renin activity and aldosterone, which all occurred independently of hydration status. On the other hand, the concentration of plasma vasopressin (PVP) was found to decrease during dehydrated immersion, but not during rehydrated immersion. It is concluded that plasma tonicity is not a factor influencing PVP suppression during water immersion.

Reliability of a Cryoscopic Micro-Osmometer Using 15-µL Plasma Samples to Measure Hydration Status in Varied Environmental Conditions

ERIC Educational Resources Information Center

Scanlan, Aaron T.; Richter-Stretton, Gina L.; Madueno, Maria C.; Borges, Nattai R.; Fenning, Andrew S.

2017-01-01

Measurement of plasma osmolality (P[subscript osm]) remains popular for assessing hydration status in exercise science. However, a controlled reliability assessment of micro-osmometry using small sample volumes to measure Posm remains to be performed. This study aimed to examine the reliability of a cryoscopic micro-osmometer requiring 15-µL…

Monitoring Hydration Status Pre- and Post-Training among University Athletes Using Urine Color and Weight Loss Indicators

ERIC Educational Resources Information Center

Webb, Marquitta C.; Salandy, Sinead T.; Beckford, Safiya E.

2016-01-01

Objective: To investigate the hydration status pre- and post-training among university athletes using urine color and weight loss as indicators. Participants: Participants were 52 university athletes training for campus games in a developing country. Methods: Pre- and post-training urine specimens were compared with a standard urine color scale.…

Effect of hydration status on pesticide uptake in anurans following exposure to contaminated soils.

PubMed

Glinski, Donna A; Henderson, W Matthew; Van Meter, Robin J; Purucker, S Thomas

2018-06-01

In this study, the impact of hydration status on dermal uptake of pesticides in two species of amphibians is examined. Absorption of pesticides in anurans occurs primarily through a highly vascularized dermal seat patch; however, pesticides can also enter through the superficial dermis following exposure. Despite the growing body of literature on dermal exposure in amphibians, little is known on how hydration status influences uptake. Thus, the objective of this study was to investigate the influence of hydration status on absorption of pesticides (atrazine, triadimefon, metolachlor, chlorothalonil, and imidacloprid) in southern leopard frogs (Lithobates sphenocephala) and Fowler's toads (Anaxyrus fowleri). Amphibian treatments included dehydration periods of 0, 2, 4, 6, 8, or 10 h prior to exposure to pesticide-contaminated soils for 8 h. Following exposure, soil and whole-body homogenates were extracted and analyzed by LC-MS/MS. Dehydration time was then regressed against post-exposure concentrations to infer the impact of dehydration on dermal pesticide uptake. Increased dehydration time resulted in significantly lowered pesticide concentrations in both species (F 6, 293  = 67.66, p = 0.007) for the five pesticides studied. This phenomenon could be due to an energy and/or dilution effect.

Hydration: certain basic aspects for developing technical and scientific parameters into the nutrition knowledge

PubMed

Perales-García, Aránzazu; Estévez-Martínez, Isabel; Urrialde, Rafael

2016-07-12

Introduction: Hydration is defined as the water intake coming from food and beverages. Its study has become an area by itself, within the nutrition field. Meaning that in 2010 the European Food Safety Authority (EFSA) approved the water intake recommendations, but the study of this topic implies a rigorous methodology, which represents several issues. Objective: Showing as a glance the main methodological issues in hydration studies. Material and methods: Bibliographic revision of scientific literature. Results: The main methodological issues presented are: sample selection (investigation field and sample design), selection of the method to evaluate hydration status (dilution techniques, bioelectrical impedance, plasmatic and urinary indicators, changes in body composition, water losses and clinic symptoms) selection of the method to evaluate water intake (biomarker, questionnaires, informatics programs, smartphone use, 24-h register, dietary history and food frequency questionnaire), and the main sources of hydration. Conclusions: Hydration status should be understood as a routine model, with daily frequency, according to gender, age, physical activity and environmental conditions. Furthermore, the correct design of the methodology has a special importance in order to take into account all the aspects

Hydration status of underground miners in a temperate Australian region

PubMed Central

2013-01-01

Background Dehydration is a health risk for miners in tropical regions of Australia. However, it is not known whether dehydration poses a health risk to miners working in temperate regions of Australia. Methods A cross-sectional study of 88 miners from two underground mines was undertaken in south-eastern New South Wales, Australia. Participants had their height, weight, waist circumference and hydration status measured and completed a self-administered questionnaire on fluid intake, access to water, and socio-demographic characteristics. Health and Safety managers were surveyed about guidelines relating to healthy work and lifestyle behaviours which impact/influence hydration. Results Hydration tests indicated that more than half of the miners (approximately 58%) were dehydrated (Urinary Specific Gravity (USG) >1.020) both before and after their shift, with three workers pre-shift and four workers post-shift displaying clinical dehydration (USG>1.030). Overall, 54.0% of participants were overweight and 36.8% were obese. Miners who commenced the shift with poor hydration status were 2.6 times more likely to end the shift with poor hydration, compared to those who commenced the shift with good hydration (OR 2.6, 95% CI 1.06, 6.44). Miners who had a mean USG result for the entire shift indicating dehydration were more likely to be obese (42.9%) and have a waist measurement in the high risk range for metabolic complications (40.8%) than those workers that were adequately hydrated for their entire shift (29.4% and 14.7% respectively). Some guidelines promoting healthy lifestyles and supportive work environments were in place, but there were limited guidelines on healthy weight and hydration. Conclusions Dehydration, being overweight and obesity were linked issues in this cohort of miners. Strategies are needed to: adapt the workplace environment to increase water accessibility; encourage appropriate consumption of water both at work and at home; and to promote physical activity and good nutrition to maintain healthy weight. PMID:23634724

Current hydration guidelines are erroneous: dehydration does not impair exercise performance in the heat.

PubMed

Wall, Bradley A; Watson, Greig; Peiffer, Jeremiah J; Abbiss, Chris R; Siegel, Rodney; Laursen, Paul B

2015-08-01

Laboratory studies that support the hydration guidelines of leading governing bodies have shown that dehydration to only -2% of body mass can lead to increase in body temperature and heart rate during exercise, and decrease in performance. These studies, however, have been conducted in relatively windless environments (ie, wind speed <12.9 km/h), without participants being blinded to their hydration status. To investigate the effect of blinded hydration status on cycling time-trial performance in the heat with ecologically valid facing wind speed conditions. During three experimental trials, 10 cyclists were dehydrated to -3% body mass by performing 2 h of submaximal exercise (walking and cycling) in the heat, before being reinfused with saline to replace 100%, 33% or 0% of fluid losses, leaving them 0%, -2% or -3% hypohydrated, respectively. Participants then completed a 25 km time trial in the heat (33°C, 40% relative humidity; wind speed 32 km/h) during which their starting hydration status was maintained by infusing saline at a rate equal to their sweat rate. The treatment was participant-blinded and the order was randomised. Completion time, power output, heart rate, rectal temperature and perceptual variables were measured. While rectal temperature was higher beyond 17 km of the time trial in the -3% vs 0% conditions (38.9±0.3°C vs 38.6±0.3°C; p<0.05), no other differences between trials were shown. When well-trained cyclists performed a 25 km cycling time trial under ecologically valid conditions and were blinded to their hydration status, performance, physiological and perceptual variables were not different between trials. These data do not support the residing basis behind many of the current hydration guidelines. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Examination of iodine status in the German population: an example for methodological pitfalls of the current approach of iodine status assessment.

PubMed

Johner, S A; Thamm, M; Schmitz, R; Remer, T

2016-04-01

Preliminary iodine concentration (UIC) measurements in spot urines of the representative German adult study DEGS indicated a severe worsening of iodine status compared to previous results in German children (KiGGS study). Therefore, we aimed to evaluate adult iodine status in detail and to investigate the impact of hydration status on UIC. UIC and creatinine concentrations were measured in 6978 spot urines from the German nationwide DEGS study (2008-2011). Twenty-four-hour iodine excretions (24-h UIE) were estimated by relating iodine/creatinine ratios to age- and sex-specific 24-h creatinine reference values. Urine osmolality was measured in two subsamples of spot urines (n = 100 each) to determine the impact of hydration status on UIC. In DEGS, median UIC was 69 µg/L in men and 54 µg/L in women, lying clearly below the WHO cutoff for iodine sufficiency (100 µg/L). Estimated median 24-h UIE was 113 µg/day, accompanied by 32 % of DEGS adults, lying below the estimated average requirement (EAR) for iodine. Comparative analysis with the KiGGS data (>14,000 spot urines of children; median UIC 117 µg/L) revealed a comparable percentage

Bioelectrical impedance vector analysis as a useful predictor of nutritional status in patients with short bowel syndrome.

PubMed

Fassini, Priscila Giacomo; Nicoletti, Carolina Ferreira; Pfrimer, Karina; Nonino, Carla Barbosa; Marchini, Júlio Sérgio; Ferriolli, Eduardo

2017-08-01

Short bowel syndrome (SBS) represents a serious intestinal absorption disorder. Therefore, patients with SBS may have severe malnutrition and excessive mineral and fluid losses. Once the assessment of nutritional status is important in their follow-up, body composition measurements and especially total body water (TBW) must be repeatedly evaluated for the assessment of changes in hydration and nutritional care. The aim of this study was to investigate if bioelectrical impedance vector analysis (BIVA) is a useful predictor of nutritional and hydration status in SBS patients. In this observational study, 22 participants (12 women), 11 with SBS and 11 gender, age and BMI-matched controls, were evaluated using the bioelectrical impedance measurements (BIA) and BIVA to assess nutritional and hydration status. Participants age was 53 ± 8 y (mean ± SD). Body water, fat mass and lean mass as assessed by BIA did not differ between the two groups. However, BIVA showed important differences between the groups regarding hydration and amount of soft tissue (p < 0.0001 for women and p = 0.0015 for men). The results also evidenced that women's vectors were related to cachexia, while men's vectors were divided into lean and cachexia quadrants. The use of BIVA analysis also evidenced hydration disturbance and losses of soft tissue. BIVA may represent a better predictor of nutritional status for analysis and interpretation of body composition in patients with short bowel syndrome. This trial was registered at ClinicalTrials.gov as NCT02113228. Copyright © 2016 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Hydration Status, Kidney Function, and Kidney Injury in Florida Agricultural Workers.

PubMed

Mix, Jacqueline; Elon, Lisa; Vi Thien Mac, Valerie; Flocks, Joan; Economos, Eugenia; Tovar-Aguilar, Antonio J; Stover Hertzberg, Vicki; McCauley, Linda A

2018-05-01

Recent findings suggest that laboring in hot occupational environments is related to kidney damage in agricultural workers. We examined hydration status and kidney function in 192 Florida agricultural workers. Blood and urine samples were collected over 555 workdays during the summers of 2015 and 2016. Urine-specific gravity (USG), serum creatinine, and other kidney function markers were examined pre- and post-shift on each workday. Multivariable mixed modeling was used to examine the association of risk factors with hydration status and acute kidney injury (AKI). Approximately 53% of workers were dehydrated (USG ≥1.020) pre-shift and 81% post-shift; 33% of participants had AKI on at least one workday. The odds of AKI increased 47% for each 5-degree (°F) increase in heat index. A strikingly high prevalence of dehydration and AKI exists in Florida agricultural workers.

The expression of proinflammatory genes in epidermal keratinocytes is regulated by hydration status.

PubMed

Xu, Wei; Jia, Shengxian; Xie, Ping; Zhong, Aimei; Galiano, Robert D; Mustoe, Thomas A; Hong, Seok J

2014-04-01

Mucosal wounds heal more rapidly, exhibit less inflammation, and are associated with minimal scarring when compared with equivalent cutaneous wounds. We previously demonstrated that cutaneous epithelium exhibits an exaggerated response to injury compared with mucosal epithelium. We hypothesized that treatment of injured skin with a semiocclusive dressing preserves the hydration of the skin and results in a wound healing phenotype that more closely resembles that of mucosa. Here we explored whether changes in hydration status alter epidermal gene expression patterns in rabbit partial-thickness incisional wounds. Using microarray studies on injured epidermis, we showed that global gene expression patterns in highly occluded versus non-occluded wounds are distinct. Many genes including IL-1β, IL-8, TNF-α (tumor necrosis factor-α), and COX-2 (cyclooxygenase 2) are upregulated in non-occluded wounds compared with highly occluded wounds. In addition, decreased levels of hydration resulted in an increased expression of proinflammatory genes in human ex vivo skin culture (HESC) and stratified keratinocytes. Hierarchical analysis of genes using RNA interference showed that both TNF-α and IL-1β regulate the expression of IL-8 through independent pathways in response to reduced hydration. Furthermore, both gene knockdown and pharmacological inhibition studies showed that COX-2 mediates the TNF-α/IL-8 pathway by increasing the production of prostaglandin E2 (PGE2). IL-8 in turn controls the production of matrix metalloproteinase-9 in keratinocytes. Our data show that hydration status directly affects the expression of inflammatory signaling in the epidermis. The identification of genes involved in the epithelial hydration pathway provides an opportunity to develop strategies to reduce scarring and optimize wound healing.

Half-marathon and full-marathon runners' hydration practices and perceptions.

PubMed

O'Neal, Eric K; Wingo, Jonathan E; Richardson, Mark T; Leeper, James D; Neggers, Yasmine H; Bishop, Phil A

2011-01-01

The behaviors and beliefs of recreational runners with regard to hydration maintenance are not well elucidated. To examine which beverages runners choose to drink and why, negative performance and health experiences related to dehydration, and methods used to assess hydration status. Cross-sectional study. Marathon registration site. Men (n = 146) and women (n = 130) (age = 38.3 ± 11.3 years) registered for the 2010 Little Rock Half-Marathon or Full Marathon. A 23-item questionnaire was administered to runners when they picked up their race timing chips. Runners were separated into tertiles (Low, Mod, High) based on z scores derived from training volume, expected performance, and running experience. We used a 100-mm visual analog scale with anchors of 0 (never) and 100 (always). Total sample responses and comparisons between tertile groups for questionnaire items are presented. The High group (58±31) reported greater consumption of sport beverages in exercise environments than the Low (42 ± 35 mm) and Mod (39 ± 32 mm) groups (P < .05) and perceived sport beverages to be superior to water in meeting hydration needs (P < .05) and improving performance during runs greater than 1 hour (P < .05). Seventy percent of runners experienced 1 or more incidents in which they believed dehydration resulted in a major performance decrement, and 45% perceived dehydration to have resulted in adverse health effects. Twenty percent of runners reported monitoring their hydration status. Urine color was the method most often reported (7%), whereas only 2% reported measuring changes in body weight. Greater attention should be paid to informing runners of valid techniques to monitor hydration status and developing an appropriate individualized hydration strategy.

Half-Marathon and Full-Marathon Runners' Hydration Practices and Perceptions

PubMed Central

O'Neal, Eric K.; Wingo, Jonathan E.; Richardson, Mark T.; Leeper, James D.; Neggers, Yasmine H.; Bishop, Phil A.

2011-01-01

Context: The behaviors and beliefs of recreational runners with regard to hydration maintenance are not well elucidated. Objective: To examine which beverages runners choose to drink and why, negative performance and health experiences related to dehydration, and methods used to assess hydration status. Design: Cross-sectional study. Setting: Marathon registration site. Patients or Other Participants: Men (n = 146) and women (n = 130) (age = 38.3 ± 11.3 years) registered for the 2010 Little Rock Half-Marathon or Full Marathon. Intervention(s): A 23-item questionnaire was administered to runners when they picked up their race timing chips. Main Outcome Measure(s): Runners were separated into tertiles (Low, Mod, High) based on z scores derived from training volume, expected performance, and running experience. We used a 100-mm visual analog scale with anchors of 0 (never) and 100 (always). Total sample responses and comparisons between tertile groups for questionnaire items are presented. Results: The High group (58±31) reported greater consumption of sport beverages in exercise environments than the Low (42 ± 35 mm) and Mod (39 ± 32 mm) groups (P < .05) and perceived sport beverages to be superior to water in meeting hydration needs (P < .05) and improving performance during runs greater than 1 hour (P < .05). Seventy percent of runners experienced 1 or more incidents in which they believed dehydration resulted in a major performance decrement, and 45% perceived dehydration to have resulted in adverse health effects. Twenty percent of runners reported monitoring their hydration status. Urine color was the method most often reported (7%), whereas only 2% reported measuring changes in body weight. Conclusions: Greater attention should be paid to informing runners of valid techniques to monitor hydration status and developing an appropriate individualized hydration strategy. PMID:22488182

Hydration status affects urea transport across rat urothelia.

PubMed

Spector, David A; Deng, Jie; Stewart, Kerry J

2011-12-01

Although mammalian urinary tract epithelium (urothelium) is generally considered impermeable to water and solutes, recent data suggest that urine constituents may be reabsorbed during urinary tract transit and storage. To study water and solute transport across the urothelium in an in vivo rat model, we instilled urine (obtained during various rat hydration conditions) into isolated in situ rat bladders and, after a 1-h dwell, retrieved the urine and measured the differences in urine volume and concentration and total quantity of urine urea nitrogen and creatinine between instilled and retrieved urine in rat groups differing by hydration status. Although urine volume did not change >1.9% in any group, concentration (and quantity) of urine urea nitrogen in retrieved urine fell significantly (indicating reabsorption of urea across bladder urothelia), by a mean of 18% (489 mg/dl, from an instilled 2,658 mg/dl) in rats receiving ad libitum water and by a mean of 39% (2,544 mg/dl, from an instilled 6,204 mg/dl) in water-deprived rats, but did not change (an increase of 15 mg/dl, P = not significant, from an instilled 300 mg/dl) in a water-loaded rat group. Two separate factors affected urea nitrogen reabsorption rates, a urinary factor related to hydration status, likely the concentration of urea nitrogen in the instilled urine, and a bladder factor(s), also dependent on the animal's state of hydration. Urine creatinine was also absorbed during the bladder dwell, and hydration group effects on the concentration and quantity of creatinine reabsorbed were qualitatively similar to the hydration group effect on urea transport. These findings support the notion(s) that urinary constituents may undergo transport across urinary tract epithelia, that such transport may be physiologically regulated, and that urine is modified during transit and storage through the urinary tract.

Does Ramadan Fasting Affect Hydration Status and Kidney Function in CKD Patients?

PubMed

Hassan, Shadia; Hassan, Fadi; Abbas, Nur; Hassan, Kamal; Khatib, Nihal; Edgim, Rabia; Fadol, Rawia; Khazim, Khaled

2018-01-01

This study is the first of its kind to examine the impact of the Ramadan fasting on hydration status, plasma brain natriuretic peptide (BNP) levels, and kidney function in chronic kidney disease (CKD) patient. This prospective cohort study included 2 groups of patients with CKD grades 2-4: thirty-one Muslim patients who fasted the month of Ramadan (fasting group) and 26 Muslim patients who did not fast (control group). One week before the Ramadan fast, in the last week of the month of Ramadan (4 weeks), and 4 weeks after the end of the Ramadan month (8 weeks), hydration status and blood analysis of urea, creatinine and BNP levels were measured. Among fasting patients, serum urea levels increased significantly (p = 0.024) during the last week of fasting and returned to basal levels at 4 weeks after the end of the Ramadan month, the estimated glomerular filtration rate did not change significantly at the end of fasting (p = 0.411), the hydration status indices and plasma BNP levels were significantly decreased after fasting (p ≤ 0.021) but returned to basal values 4 weeks thereafter. Patients with CKD grades 2-4 can fast throughout the month of Ramadan with no significant deterioration of renal functions and with a reasonable degree of safety. © 2018 S. Karger AG, Basel.

Assessment of hydration status using bioelectrical impedance vector analysis in critical patients with acute kidney injury.

PubMed

Hise, Ana Cláudia da Rosa; Gonzalez, Maria Cristina

2018-04-01

The state of hyperhydration in critically ill patients with acute kidney injury (AKI) is associated with increased mortality. Bioelectrical impedance vector analysis (BIVA) appears to be a viable method to access the fluid status of critical patients but has never been evaluated in critical patients with AKI. The objective of this study is to evaluate the hydration status measured using BIVA in critical patients under intensive care at the time of AKI diagnosis and to correlate this measurement with mortality. We assessed the fluid status measured using BIVA in 224 critical patients at the time of AKI diagnosis and correlated it with mortality. To interpret the results, BIVA Software 2002 was used to plot the data from the patients studied on the 95% confidence ellipses of the RX c plane for comparisons between groups (non-survivors, survivors). Variables such as mechanical ventilation, vasoactive drug, and sepsis, among others, were collected. The impedance vector analysis conducted using BIVA Software 2002 indicated changes in the body compositions of patients according to the 95% confidence ellipse between the vectors R/H and X c /H of the group of survivors and the group of deceased patients. Hotelling's test (T 2  = 21.2) and the F test (F = 10.6) revealed significant differences (p < 0.001) between the two groups. These results demonstrate that patients who died presented with a greater hydration volume at the time of AKI diagnosis compared with those who survived. In addition to the hydration status measured using BIVA, the following were also correlated with death: diagnosis at hospitalization, APACHE II score, length of hospital stay, RIFLE score, maximum organ failure, sepsis type, hemoglobin, and AF. The fluid status assessment measured using BIVA significantly demonstrated the difference in hydration between survivors and non-survivors among critically ill patients with AKI. Copyright © 2017 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

Skin hydration and lifestyle-related factors in community-dwelling older people.

PubMed

Iizaka, Shinji

2017-09-01

This study aimed to investigate skin hydration status of the lower legs by comparing several methods and examining lifestyle-related factors in community-dwelling older people. A cross-sectional study was conducted in three community settings in Japan from autumn to winter. Participants were older people aged ≥65 years (n=118). Skin hydration status of the lower legs was evaluated by stratum corneum hydration using an electrical device, clinical symptoms by an expert's observation and the visual analogue scale. Lifestyle factors of skin care were evaluated by a self-administered questionnaire. The mean age of participants was 74.4 years and 83.9% were women. Stratum corneum hydration was significantly correlated with clinical scores by an expert's observation (rho=-0.46, P<0.001), but it was not correlated with the visual analogue scale (rho=-0.08, P=0.435). Among participants who did not perceive dry skin, 57.5% showed low stratum corneum hydration. Hospitalization in the past year (b=-9.4, P=0.008), excessive bathing habits (b=-4.6, P=0.014), and having an outdoor hobby (b=-5.7, P=0.007) were negatively associated, and diuretics (b=11.5, P=0.002) and lotion-type moisturizer use (b=4.6, P=0.022) were positively associated with stratum corneum hydration. Stratum corneum hydration measurements show an adequate association with observation-based evaluation by an expert, but poor agreement with subjective evaluation in community-dwelling older people. Hospitalization experience and lifestyle factors are associated with skin hydration. Copyright © 2017 Elsevier B.V. All rights reserved.

A possible source of water in seismogenic subduction zones

NASA Astrophysics Data System (ADS)

Kameda, J.; Yamaguchi, A.; Kimura, G.; Iodp Exp. 322 Scientists

2010-12-01

Recent works on the subduction megathrusts have emphasized the mechanical function of fluids contributing dynamic slip-weakening. Basalt-hosting fault zones in on-land accretionary complexes present several textures of seismic slip under fluid-assisted condition such as implosion breccia with carbonate matrix and decrepitation of fluid inclusion. In order to clarify initiation and evolution processes of such fault zones as well as possible source of fluid in the seismogenic subduction zone, we examined a mineralogical/geochemical feature of basaltic basement recovered by IODP Exp. 322 at C0012, that is a reference site for subduction input in the Nankai Trough. A total of 10 samples (about 4 m depth interval from the basement top) were analyzed in this study. XRD analyses indicate that all of the samples contain considerable amount of smectite. The smectite does not appear as a form of interstratified phase with illite or chlorite. Preliminary chemical analyses by EDS in TEM suggest that the smectite is trioctahedral saponite with Ca as a dominant interlayer cation. To determine the saponite content quantitatively, cation exchange capacity (CEC) of bulk samples was measured. The samples show almost similar CEC of around 30 meq/100g, implying that bulk rock contains about 30 wt% of saponite, considering a general CEC of 100 meq/100g for monomineralic saponite. Such abundance of saponite might be a result from intense alteration of oceanic crust due to sea water circulation at low temperature. Previous experimental work suggests that saponite might be highly hydrated (two to three water layer hydration form) at the seismogenic P-T condition. Hence, altered upper oceanic crust is a possible water sink in the seismogenic zone. The water stored in the smectite interlayer region will be expelled via smectite to chlorite transition reaction, that might contribute to the dynamic weakening of the seimogenic plate boundary between the basement basalt and overlying accretionary prism.

Tipping Point for Expansion of Layered Aluminosilicates in Weakly Polar Solvents: Supercritical CO 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaef, Herbert T.; Loganathan, Narasimhan; Bowers, Geoffrey M.

Layered aluminosilicates play a dominant role in the mechanical and gas storage properties of the subsurface, are used in diverse industrial applications, and serve as model materials for understanding solvent-ion-support systems. Although expansion in the presence of H2O is well known to be systematically correlated with the hydration free energy of the interlayer cation, in environments dominated by non-polar solvents (i.e. CO2), uptake into the interlayer is not well-understood. Using novel high pressure capabilities, we investigated the interaction of super-critical CO2 with Na+-, NH4+-, and Cs+-saturated montmorillonite, comparing results with predictions from molecular dynamics simulations. Despite the known trend inmore » H2O, and that cation solvation energies in CO2 suggest a stronger interaction with Na+, both the NH4+- and Cs+-clays readily absorbed CO2 and expanded while the Na+-clay did not. The apparent inertness of the Na+-clay was not due to kinetics, as experiments seeking a stable expanded state showed that none exists. Molecular dynamics simulations revealed a large endothermicity to CO2 intercalation in the Na+-clay, but little or no energy barrier for the NH4+- and Cs+-clays. Consequently, we have shown for the first time that in the presence of a low dielectric constant gas swelling depends more on the strength of the interaction between interlayer cation and aluminosilicate sheets and less on that with solvent. The finding suggests a distinct regime in layered aluminosilicates swelling behavior triggered by low solvent polarizability, with important implications in geomechanics, storage and retention of volatile gases, and across industrial uses in gelling, decoloring, heterogeneous catalysis, and semi-permeable reactive barriers.« less

The 10Å phase: a high-pressure expandable sheet silicate stable during subduction of hydrated lithosphere

NASA Astrophysics Data System (ADS)

Fumagalli, Patrizia; Stixrude, Lars; Poli, Stefano; Snyder, Don

2001-03-01

H 2O storage and release in deep subducting lithosphere is controlled by complex reaction suites involving a variety of hydrous phases. As a result of its relatively large thermal stability and intermediate composition, the 10Å phase (Mg 3Si 4O 10(OH) 2· nH 2O) has been regarded as a relevant H 2O reservoir in a wide range of rock compositions and mineral assemblages. High-pressure syntheses of the 10Å phase were carried out at 6.7 GPa and 650°C under fluid-saturated conditions in a Walker-type multi-anvil apparatus, from 5 min to 430 h. X-ray powder diffraction of large platy hexagonal crystals of the 10Å phase (up to 100 μm) were indexed on the basis of a trioctahedral-type structure. Long-term run products (>110 h) reveal sensitivity of the 10Å phase to treatment with acetone leading to the appearance of diffractions at greater d-spacings (10.2-11.6 Å) with respect to the basal peak of the 10Å phase (9.64-10.07 Å). This swelling behavior is strongly related to synthesis run duration. The Raman spectrum of the 10Å phase at frequencies less than 800 cm -1 shows a strong similarity to talc. In the Si-O stretching region (800-1100 cm -1), the 10Å phase exhibits three modes (909, 992 and 1058 cm -1), as compared to two in talc. The bending mode of water (ν 2) is found at 1593 cm -1. In the OH stretching region, peaks at 3593, 3622 and 3668 cm -1 were observed. The acetone treated sample shows a C-H stretching mode at 2923 cm -1 while the double bond CO signal is absent. The swelling behavior of the 10Å phase is interpreted as due to intercalation of acetone with pre-existing interlayer water. The efficiency of this process is dependent on the amount of the interlayer water which in turn depends on run duration. The relation between the response to acetone treatment and run duration is therefore interpreted as a time-dependent hydration of the 10Å phase. The fractions transformed from non-expandable to expandable fractions was fitted to the Avrami empirical law which suggests that kinetics are mainly controlled by diffusion rather than phase boundary reactions. The ability to accommodate variable amounts of H 2O makes the 10Å phase a major H 2O sink whenever a hydrous phase such as chlorite and serpentine breaks down during prograde transformations in the subducted lithosphere. Under H 2O-saturated conditions, a fully hydrated 10Å phase occurs; when H 2O-undersaturated conditions prevail, a H 2O-deficient 10Å phase incorporates the volatile component available. The exchange capacity of interlayer molecules in the 10Å phase structure opens new scenarios on the control of fluid compositions escaping from subducted slabs.

Fluid intake, hydration, work physiology of wildfire fighters working in the heat over consecutive days.

PubMed

Raines, Jenni; Snow, Rodney; Nichols, David; Aisbett, Brad

2015-06-01

(i) To evaluate firefighters' pre- and post-shift hydration status across two shifts of wildfire suppression work in hot weather conditions. (ii) To document firefighters' fluid intake during and between two shifts of wildfire suppression work. (iii) To compare firefighters' heart rate, activity, rating of perceived exertion (RPE), and core temperature across the two consecutive shifts of wildfire suppression work. Across two consecutive days, 12 salaried firefighters' hydration status was measured immediately pre- and post-shift. Hydration status was also measured 2h post-shift. RPE was also measured immediately post-shift on each day. Work activity, heart rate, and core temperature were logged continuously during each shift. Ten firefighters also manually recorded their food and fluid intake before, during, and after both fireground shifts. Firefighters were not euhydrated at all measurement points on Day one (292±1 mOsm l(-1)) and euhydrated across these same time points on Day two (289±0.5 mOsm l(-1)). Fluid consumption following firefighters' shift on Day one (1792±1134ml) trended (P = 0.08) higher than Day two (1108±1142ml). Daily total fluid intake was not different (P = 0.27), averaging 6443±1941ml across both days. Core temperature and the time spent ≥ 70%HRmax were both elevated on Day one (when firefighters were not euhydrated). Firefighters' work activity profile was not different between both days of work. There was no difference in firefighters' pre- to post-shift hydration within each shift, suggesting ad libitum drinking was at least sufficient to maintain pre-shift hydration status, even in hot conditions. Firefighters' relative hypohydration on Day one (despite a slightly lower ambient temperature) may have been associated with elevations in core temperature, more time in the higher heart rate zones, and 'post-shift' RPE. © The Author 2015. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Evaluation of quality improvement initiative in pediatric oncology: implementation of aggressive hydration protocol.

PubMed

Fratino, Lisa M; Daniel, Denise A; Cohen, Kenneth J; Chen, Allen R

2009-01-01

Our goal was to improve the efficiency of chemotherapy administration for pediatric oncology patients. We identified prechemotherapy hydration as the process that most often delayed chemotherapy administration. An aggressive hydration protocol, supported by fluid order sets, was developed for patients receiving planned chemotherapy. The mean interval from admission to achieving adequate hydration status was reduced significantly from 4.9 to 1.4 hours with a minor reduction in the time to initiate chemotherapy from 9.6 to 8.6 hours. Chemotherapy availability became the new rate-limiting process.

Clinical, biochemical, and hygiene assessment of stabled horses provided continuous or intermittent access to drinking water.

PubMed

Freeman, D A; Cymbaluk, N F; Schott, H C; Hinchcliff, K; McDonnell, S M; Kyle, B

1999-11-01

To compare health, hydration status, and management of stabled pregnant mares provided drinking water continuously or via 1 of 3 intermittent delivery systems. 22 Quarter Horse (QH) or QH-crossbred mares and 18 Belgian or Belgian-crossbred mares (study 1); 24 QH or QH-crossbred mares and 18 Belgian or Belgian-crossbred mares (study 2). Stabled horses were provided water continuously or via 1 of 3 intermittent water delivery systems in 2 study periods during a 2-year period. Body temperature, attitude, appetite, water intake, and urine output were recorded daily. Hygiene of each horse and the stable were assessed weekly. Clinical and biochemical measures of hydration were determined 3 times during each study. Clinical measures of hydration included skin turgor, gum moisture, capillary refill time, and fecal consistency. Biochemical measures of hydration included PCV, plasma total protein concentration, serum osmolality, plasma vasopressin concentration, urine specific gravity, and urine osmolality. All horses remained healthy. Stable hygiene was worse when horses had continuous access to water. Clinical and biochemical measures of hydration did not differ among water delivery systems. Various continuous and intermittent water delivery systems provided adequate amounts of water to stabled horses to maintain health and hydration status. Providing intermittent access to water may be preferable on the basis of stable hygiene.

Inadequate Hydration, BMI, and Obesity Among US Adults: NHANES 2009-2012.

PubMed

Chang, Tammy; Ravi, Nithin; Plegue, Melissa A; Sonneville, Kendrin R; Davis, Matthew M

2016-07-01

Improving hydration is a strategy commonly used by clinicians to prevent overeating with the goal of promoting a healthy weight among patients. The relationship between weight status and hydration, however, is unclear. Our objective was to assess the relationship between inadequate hydration and BMI and inadequate hydration and obesity among adults in the United States. Our study used a nationally representative sample from the National Health and Nutrition Examination Survey (NHANES) 2009 to 2012, and included adults aged 18 to 64 years. The primary outcome of interest was body mass index (BMI), measured in continuous values and also categorized as obese (BMI ≥30) or not (BMI <30). Individuals with urine osmolality values of 800 mOsm/kg or greater were considered to be inadequately hydrated. Linear and logistic regressions were performed with continuous BMI and obesity status as the outcomes, respectively. Models were adjusted for known confounders including age, race/ethnicity, sex, and income-to-poverty ratio. In this nationally representative sample (n = 9,528; weighted n = 193.7 million), 50.8% were women, 64.5% were non-Hispanic white, and the mean age was 41 years. Mean urine osmolality was 631.4 mOsm/kg (SD = 236.2 mOsm/kg); 32.6% of the sample was inadequately hydrated. In adjusted models, adults who were inadequately hydrated had higher BMIs (1.32 kg/m(2); 95% CI, 0.85-1.79; P <.001) and higher odds of being obese (OR = 1.59; 95% CI, 1.35-1.88; P <.001) compared with hydrated adults. We found a significant association between inadequate hydration and elevated BMI and inadequate hydration and obesity, even after controlling for confounders. This relationship has not previously been shown on a population level and suggests that water, an essential nutrient, may deserve greater focus in weight management research and clinical strategies. © 2016 Annals of Family Medicine, Inc.

Lignin Depolymerization with Nitrate-Intercalated Hydrotalcite Catalysts

DOE PAGES

Kruger, Jacob S.; Cleveland, Nicholas S.; Zhang, Shuting; ...

2016-01-13

Hydrotalcites (HTCs) exhibit multiple adjustable parameters to tune catalytic activity, including interlayer anion composition, metal hydroxide layer composition, and catalyst preparation methods. Here in this paper, we report the influence of several of these parameters on β-O-4 bond scission in a lignin model dimer, 2-phenoxy-1-phenethanol (PE), to yield phenol and acetophenone. We find that the presence of both basic and NO 3– anions in the interlayer increases the catalyst activity by 2–3-fold. In contrast, other anions or transition metals do not enhance catalytic activity in comparison to blank HTC. The catalyst is not active for C–C bond cleavage on ligninmore » model dimers and has no effect on dimers without an α-OH group. Most importantly, the catalyst is highly active in the depolymerization of two process-relevant lignin substrates, producing a significant amount of low-molecular-weight aromatic species. The catalyst can be recycled until the NO 3– anions are depleted, after which the activity can be restored by replenishing the NO 3– reservoir and regenerating the hydrated HTC structure. These results demonstrate a route to selective lignin depolymerization in a heterogeneous system with an inexpensive, earth-abundant, commercially relevant, and easily regenerated catalyst.« less

Nutrition Status Parameters and Hydration Status by Bioelectrical Impedance Vector Analysis Were Associated With Lung Function Impairment in Children and Adolescents With Cystic Fibrosis.

PubMed

Hauschild, Daniela Barbieri; Barbosa, Eliana; Moreira, Emilia Addison Machado; Ludwig Neto, Norberto; Platt, Vanessa Borges; Piacentini Filho, Eduardo; Wazlawik, Elisabeth; Moreno, Yara Maria Franco

2016-06-01

(1) To compare nutrition and hydration status between a group of children/adolescents with cystic fibrosis (CFG; n = 46; median age, 8.5 years) and a control group without cystic fibrosis (CG). (2) To examine the association of nutrition and hydration status with lung function in the CFG. A cross-sectional study. Nutrition screening, anthropometric parameters, and bioelectrical impedance analysis (BIA) were assessed. The z scores for body mass index for age, height for age, mid upper arm circumference, triceps and subscapular skinfold thickness, mid upper arm muscle area, resistance/height, and reactance/height were calculated. Bioelectrical impedance vector analysis was conducted. Forced expiratory volume in 1 second <80% was considered lung function impairment. An adjusted logistic regression was applied (P < .05). In the CFG, lung function impairment was observed in 51.1%. All anthropometric parameters were lower, and the mean z-resistance/height and z-reactance/height were higher in the CFG (P < .05) compared with the CG. In the CFG, 43% were severely/mildly dehydrated, while none were in the CG (P = .007). In the CFG, there was an association between high nutrition risk-via nutrition screening (odds ratio [OR], 22.28; P < .05), lower values of anthropometric parameters, higher z-resistance/height (OR, 2.23; P < .05) and z-reactance/height (OR, 1.81; P < .05), and dehydration (OR, 4.94; P < .05)-and lung function impairment. The CFG exhibited a compromised nutrition status assessed by anthropometric and BIA parameters. Nutrition screening, anthropometric and BIA parameters, and hydration status were associated with lung function. © 2016 American Society for Parenteral and Enteral Nutrition.

Ad libitum fluid intake does not prevent dehydration in suboptimally hydrated young soccer players during a training session of a summer camp.

PubMed

Arnaoutis, Giannis; Kavouras, Stavros A; Kotsis, Yiannis P; Tsekouras, Yiannis E; Makrillos, Michalis; Bardis, Costas N

2013-06-01

There is a lack of studies concerning hydration status of young athletes exercising in the heat. To assess preexercise hydration status in young soccer players during a summer sports camp and to evaluate body- water balance after soccer training sessions. Initial hydration status was assessed in 107 young male soccer players (age 11-16 yr) during the 2nd day of the camp. Seventy-two athletes agreed to be monitored during 2 more training sessions (3rd and 5th days of the camp) to calculate dehydration via changes in body weight, while water drinking was allowed ad libitum. Hydration status was assessed via urine specific gravity (USG), urine color, and changes in total body weight. Mean environmental temperature and humidity were 27.2 ± 2 °C and 57% ± 9%, respectively. According to USG values, 95 of 107 of the players were hypohydrated (USG ≥ 1.020) before practice. The prevalence of dehydration observed was maintained on both days, with 95.8% and 97.2% of the players being dehydrated after the training sessions on the 3rd and 5th days, respectively. Despite fluid availability, 54 of the 66 (81.8%) dehydrated players reduced their body weight (-0.35 ± 0.04 kg) as a response to training, while 74.6% (47 out of the 63) further reduced their body weight (-0.22 ± 0.03 kg) after training on the 5th day. Approximately 90% of the young soccer players who began exercising under warm weather conditions were hypohydrated, while drinking ad libitum during practice did not prevent further dehydration in already dehydrated players.

Non-invasive estimation of hydration status changes through tear fluid osmolarity during exercise and post-exercise rehydration.

PubMed

Ungaro, Corey T; Reimel, Adam J; Nuccio, Ryan P; Barnes, Kelly A; Pahnke, Matthew D; Baker, Lindsay B

2015-05-01

To determine if tear fluid osmolarity (Tosm) can track changes in hydration status during exercise and post-exercise rehydration. Nineteen male athletes (18-37 years, 74.6 ± 7.9 kg) completed two randomized, counterbalanced trials; cycling (~95 min) with water intake to replace fluid losses or water restriction to progressively dehydrate to 3 % body mass loss (BML). After exercise, subjects drank water to maintain body mass (water intake trials) or progressively rehydrate to pre-exercise body mass (water restriction trials) over a 90-min recovery period. Plasma osmolality (Posm) and Tosm measurements (mean of right and left eyes) were taken pre-exercise, during rest periods between exercise bouts corresponding to 1, 2, and 3 % BML, and rehydration at 2, 1, and 0 % BML. During exercise mean (± SD) Tosm was significantly higher in water restriction vs. water intake trials at 1 % BML (299 ± 9 vs. 293 ± 9 mmol/L), 2 % BML (301 ± 9 vs. 294 ± 9 mmol/L), and 3 % BML (302 ± 9 vs. 292 ± 8 mmol/L). Mean Tosm progressively decreased during post-exercise rehydration and was not different between trials at 1 % BML (291 ± 8 vs. 290 ± 7 mmol/L) and 0 % BML (288 ± 7 vs. 289 ± 8 mmol/L). Mean Tosm tracked changes in hydration status similar to that of mean Posm; however, the individual responses in Tosm to water restriction and water intake was considerably more variable than that of Posm. Tosm is a valid indicator of changes in hydration status when looking at the group mean; however, large differences among subjects in the Tosm response to hydration changes limit its validity for individual recommendations.

Clinical, analytical and bioimpedance characteristics of persistently overhydrated haemodialysis patients.

PubMed

Castellano, Sandra; Palomares, Inés; Molina, Manuel; Pérez-García, Rafael; Aljama, Pedro; Ramos, Rosa; Merello, J Ignacio

2014-11-17

Fluid overload is an important and modifiable cardiovascular risk factor for haemodialysis patients. So far, the diagnosis was based on clinical methods alone. Nowadays, we have new tools to assess more objectively the hydration status of the patients on haemodialysis, as BCM (Body Composition Monitor). A Relative Overhydration (AvROH) higher than 15% (it means, Absolute Overhydration or AWOH higher than 2.5 Litres) is associated to greater risk in haemodialysis. However, there is a group of maintained hyperhydrated patients. The aim of the present study is to identify the characteristics of patients with maintained hyperhydrated status (AvROH higher than 15% or AWOH higher than 2.5 liters). The secondary aim is to show the hemodynamic and analytical changes that are related to the reduction in hyperhydration status. Longitudinal cohort study during six months in 2959 patients in haemodialysis (HD) that are grouped according to their hydration status by BCM. And we compare their clinical, analytical and bioimpedance spectroscopy parameters. The change in overhydration status is followed by a decrease in blood pressure and the need for hypotensive drugs (AHT) and erythropoiesis stimulating agents (ESA). The target hydration status is not reached by two subgroups of patients. First, in diabetic patients with a high comorbidity index and high number of hypotensive drugs (AHT) but a great positive sodium gradient during dialysis sessions; and, younger non-diabetic patients with longer time on hemodialysis and positive sodium gradient, lower fat tissue index (FTI) but similar lean tissue index (LTI) and albumin than those with a reduction in hyperhydration status. Those patients with a reduction in hyperhydration status, also show a better control in blood pressure and anemia with less number of AHT and ESA. The maintained hyperhydrated patients, diabetic patients with many comorbidities and young men patients with longer time on hemodialysis and non-adherence treatment, can profit from a constant monitoring of their hydration state as well as an individualized treatment (dialysis and drugs).

Clay hydration/dehydration in dry to water-saturated supercritical CO2: Implications for caprock integrity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loring, John S.; Schaef, Herbert T.; Thompson, Christopher J.

2013-01-01

Injection of supercritical CO2 (scCO2) for the geologic storage of carbon dioxide will displace formation water, and the pore space adjacent to overlying caprocks could eventually be dominated by dry to water-saturated scCO2. Wet scCO2 is highly reactive and capable of carbonating and hydrating certain minerals, whereas anhydrous scCO2 can dehydrate water-containing minerals. Because these geochemical processes affect solid volume and thus porosity and permeability, they have the potential to affect the long-term integrity of the caprock seal. In this study, we investigate the swelling and shrinkage of an expandable clay found in caprock formations, montmorillonite (Ca-STx-1), when exposed tomore » variable water-content scCO2 at 50 °C and 90 bar using a combination of in situ probes, including X-ray diffraction (XRD), in situ magic angle spinning nuclear magnetic resonance spectroscopy (MAS NMR), and in situ attenuated total reflection infrared spectroscopy (ATR-IR). We show that the extent of montmorillonite clay swelling/shrinkage is dependent not only on water hydration/dehydration, but also on CO2 intercalation reactions. Our results also suggest a competition between water and CO2 for interlayer residency where increasing concentrations of intercalated water lead to decreasing concentrations of intercalated CO2. Overall, this paper demonstrates the types of measurements required to develop fundamental knowledge that will enhance modeling efforts and reduce risks associated with subsurface storage of CO2.« less

Hydration status influences the measurement of arterial stiffness.

PubMed

Caldwell, Aaron R; Tucker, Matthew A; Burchfield, Jenna; Moyen, Nicole E; Satterfield, Alf Z; Six, Ashley; McDermott, Brendon P; Mulvenon, Sean W; Ganio, Matthew S

2018-05-01

Consensus guidelines have attempted to standardize the measurement and interpretation of pulse wave velocity (PWV); however, guidelines have not addressed whether hydration status affects PWV. Moreover, multiple studies have utilized heat stress to reduce arterial stiffness which may lead to dehydration. This study utilized two experiments to investigate the effects of dehydration on PWV at rest and during passive heat stress. In experiment 1, subjects (n = 19) completed two trials, one in which they arrived euhydrated and one dehydrated (1·2[1·0]% body mass loss). In experiment 2, subjects (n = 11) began two trials euhydrated and in one trial did not receive water during heat stress, thus becoming dehydrated (1·6[0·6]% body mass loss); the other trial subjects remained euhydrated. Using Doppler ultrasound, carotid-to-femoral (central) and carotid-to-radial (peripheral) PWVs were measured. PWV was obtained at a normothermic baseline, and at a 0·5°C and 1°C elevation in rectal temperature (via passive heating). In experiment 1, baseline central PWV was significantly higher when euhydrated compared to dehydrated (628[95] versus 572[91] cm s -1 , respectively; P<0·05), but peripheral PWV was unaffected (861[117] versus 825[149] cm s -1 ; P>0·05). However, starting euhydrated and becoming dehydrated during heating in experiment 2 did not affect PWV measures (P>0·05), and independent of hydration status peripheral PWV was reduced when rectal temperature was elevated 0·5°C (-74[45] cm s -1 ; P<0·05) and 1·0°C (-70[48] cm s -1 ; P<0·05). Overall, these data suggest that hydration status affects measurements of central PWV in normothermic, resting conditions. Therefore, future guidelines should suggest that investigators ensure adequate hydration status prior to measures of PWV. © 2017 Scandinavian Society of Clinical Physiology and Nuclear Medicine. Published by John Wiley & Sons Ltd.

SPERMATID MICRONUCLEUS ANALYSES OF TRICHLOROETHYLENE AND CHLORAL HYDRATE EFFECTS IN MICE

EPA Science Inventory

Mice were exposed by inhalation to trichloroethylene (TCE), or by i.p. injection to the TCE metabolite, chloral hydrate (CH). arly spermatids were analyzed for micronucleus (MN) frequency and kinetochore status (presence or absence) using fluorochrome-labeled anti-kinetochore ant...

The impact of sub-clinical over-hydration on left ventricular mass in peritoneal dialysis patients.

PubMed

Hassan, Kamal; Hassan, Dunia; Shturman, Alexander; Rubinchik, Irina; Fadi, Hassan; Shadi, Hassan; Atar, Shaul

2015-01-01

Left ventricular hypertrophy (LVH) represents a major predictor of the development of cardiovascular (CV) complications. Over-hydration (OH) is an important uremic risk factor associated with LVH and increased CV morbidity and mortality in peritoneal dialysis (PD) patients. In the present study we evaluated the prevalence of sub-clinical OH (SCOH) among PD patients and its effects on left ventricular mass (LVM). In this cross sectional study hydration status, blood pressure, glucose load, systemic inflammation and LVM were evaluated in 43 clinically stable patients on maintenance PD for 24-76 months. The hydration status was assessed by whole-body bio-impedance spectroscopy (BIS). Peripheral edema and any evidence of pulmonary congestion were considered clinical signs of OH. OH ≥ 1.5 L was detected in 26 (60.5%) of the study participants; the OH in 19 (73.1%) of them was sub-clinical. Only 23.5% (4/17) of patients with OH < 1.5 L had LVH compared to 68.4% (13/19) of those with SCOH ≥ 1.5 L (P = 0.007). Compared to patients with OH < 1.5 L, patients with SCOH ≥ 1.5 L had higher levels of blood pressure, peritoneal glucose load, plasma brain natriuretic peptide, high sensitive C-reactive protein, interleukin-6 and LVMI; and lower levels of serum albumin (P < 0.001). No significant differences were found between patients with clinical OH or SCOH with OH ≥ 1.5 L. SCOH is highly prevalent among PD patients and may contribute to the development of LVH. Considering the poor prognosis associated with over-hydrated PD patients, periodic assessment of hydration status using accurate BIS is suggested.

Hydration, Fluid Intake, and Related Urine Biomarkers among Male College Students in Cangzhou, China: A Cross-Sectional Study-Applications for Assessing Fluid Intake and Adequate Water Intake.

PubMed

Zhang, Na; Du, Songming; Tang, Zhenchuang; Zheng, Mengqi; Yan, Ruixia; Zhu, Yitang; Ma, Guansheng

2017-05-11

The objectives of this study were to assess the associations between fluid intake and urine biomarkers and to determine daily total fluid intake for assessing hydration status for male college students. A total of 68 male college students aged 18-25 years recruited from Cangzhou, China completed a 7-day cross-sectional study. From day 1 to day 7; all subjects were asked to complete a self-administered 7-day 24-h fluid intake record. The foods eaten by subjects were weighed and 24-h urine was collected for three consecutive days on the last three consecutive days. On the sixth day, urine osmolality, specific gravity (USG), pH, and concentrations of potassium, sodium, and chloride was determined. Subjects were divided into optimal hydration, middle hydration, and hypohydration groups according to their 24-h urine osmolality. Strong relationships were found between daily total fluid intake and 24-h urine biomarkers, especially for 24-h urine volume ( r = 0.76; p < 0.0001) and osmolality ( r = 0.76; p < 0.0001). The percentage of the variances in daily total fluid intake ( R ²) explained by PLS (partial least squares) model with seven urinary biomarkers was 68.9%; two urine biomarkers-24-h urine volume and osmolality-were identified as possible key predictors. The daily total fluid intake for assessing optimal hydration was 2582 mL, while the daily total fluid intake for assessing hypohydration was 2502 mL. Differences in fluid intake and urine biomarkers were found among male college students with different hydration status. A strong relationship existed between urine biomarkers and fluid intake. A PLS model identified that key variables for assessing daily total fluid intake were 24-h urine volume and osmolality. It was feasibility to use total fluid intake to judge hydration status.

Changes in hydration status of elite Olympic class sailors in different climates and the effects of different fluid replacement beverages

PubMed Central

2013-01-01

Background Olympic class sailing poses physiological challenges similar to other endurance sports such as cycling or running, with sport specific challenges of limited access to nutrition and hydration during competition. As changes in hydration status can impair sports performance, examining fluid consumption patterns and fluid/electrolyte requirements of Olympic class sailors is necessary to develop specific recommendations for these elite athletes. The purpose of this study was to examine if Olympic class sailors could maintain hydration status with self-regulated fluid consumption in cold conditions and the effect of fixed fluid intake on hydration status in warm conditions. Methods In our cold condition study (CCS), 11 elite Olympic class sailors were provided ad libitum access to three different drinks. Crystal Light (control, C); Gatorade (experimental control, G); and customized sailing-specific Infinit (experimental, IN) (1.0:0.22 CHO:PRO), were provided on three separate training days in cold 7.1°C [4.2 – 11.3]. Our warm condition study (WCS) examined the effect of fixed fluid intake (11.5 mL.kg.-1.h-1) of C, G and heat-specific experimental Infinit (INW)(1.0:0.074 CHO:PRO) on the hydration status of eight elite Olympic Laser class sailors in 19.5°C [17.0 - 23.3]. Both studies used a completely random design. Results In CCS, participants consumed 802 ± 91, 924 ± 137 and 707 ± 152 mL of fluid in each group respectively. This did not change urine specific gravity, but did lead to a main effect for time for body mass (p < 0.001), blood sodium, potassium and chloride with all groups lower post-training (p < 0.05). In WCS, fixed fluid intake increased participant’s body mass post-training in all groups (p < 0.01) and decreased urine specific gravity post-training (p < 0.01). There was a main effect for time for blood sodium, potassium and chloride concentration, with lower values observed post-training (p < 0.05). C blood sodium concentrations were lower than the INW group post-training (p = 0.031) with a trend towards significance in the G group (p = 0.069). Conclusion Ad libitum fluid consumption in cold conditions was insufficient in preventing a decrease in body mass and blood electrolyte concentration post-training. However, when a fixed volume of 11.5 mL.kg.-1.h-1 was consumed during warm condition training, hydration status was maintained by preventing changes in body mass and urine specific gravity. PMID:23432855

Changes in hydration status of elite Olympic class sailors in different climates and the effects of different fluid replacement beverages.

PubMed

Lewis, Evan Jh; Fraser, Sarah J; Thomas, Scott G; Wells, Greg D

2013-02-21

Olympic class sailing poses physiological challenges similar to other endurance sports such as cycling or running, with sport specific challenges of limited access to nutrition and hydration during competition. As changes in hydration status can impair sports performance, examining fluid consumption patterns and fluid/electrolyte requirements of Olympic class sailors is necessary to develop specific recommendations for these elite athletes. The purpose of this study was to examine if Olympic class sailors could maintain hydration status with self-regulated fluid consumption in cold conditions and the effect of fixed fluid intake on hydration status in warm conditions. In our cold condition study (CCS), 11 elite Olympic class sailors were provided ad libitum access to three different drinks. Crystal Light (control, C); Gatorade (experimental control, G); and customized sailing-specific Infinit (experimental, IN) (1.0:0.22 CHO:PRO), were provided on three separate training days in cold 7.1°C [4.2 - 11.3]. Our warm condition study (WCS) examined the effect of fixed fluid intake (11.5 mL.kg.-1.h-1) of C, G and heat-specific experimental Infinit (INW)(1.0:0.074 CHO:PRO) on the hydration status of eight elite Olympic Laser class sailors in 19.5°C [17.0 - 23.3]. Both studies used a completely random design. In CCS, participants consumed 802 ± 91, 924 ± 137 and 707 ± 152 mL of fluid in each group respectively. This did not change urine specific gravity, but did lead to a main effect for time for body mass (p < 0.001), blood sodium, potassium and chloride with all groups lower post-training (p < 0.05). In WCS, fixed fluid intake increased participant's body mass post-training in all groups (p < 0.01) and decreased urine specific gravity post-training (p < 0.01). There was a main effect for time for blood sodium, potassium and chloride concentration, with lower values observed post-training (p < 0.05). C blood sodium concentrations were lower than the INW group post-training (p = 0.031) with a trend towards significance in the G group (p = 0.069). Ad libitum fluid consumption in cold conditions was insufficient in preventing a decrease in body mass and blood electrolyte concentration post-training. However, when a fixed volume of 11.5 mL.kg.-1.h-1 was consumed during warm condition training, hydration status was maintained by preventing changes in body mass and urine specific gravity.

Associations Between Hydration Status, Intravenous Fluid Administration, and Outcomes of Patients Infected With Shiga Toxin-Producing Escherichia coli: A Systematic Review and Meta-analysis.

PubMed

Grisaru, Silviu; Xie, Jianling; Samuel, Susan; Hartling, Lisa; Tarr, Phillip I; Schnadower, David; Freedman, Stephen B

2017-01-01

The associations between hydration status, intravenous fluid administration, and outcomes of patients infected with Shiga toxin-producing Escherichia coli (STEC) remain unclear. To determine the relationship between hydration status, the development and severity of hemolytic uremic syndrome (HUS), and adverse outcomes in STEC-infected individuals. MEDLINE, EMBASE, Cochrane Central Register of Controlled Trials via the OvidSP platform, PubMed via the National Library of Medicine, CINAHL Plus with full text, Scopus, Web of Science, ClinicalTrials.gov, reference lists, and gray literature were systematically searched. Two reviewers independently identified studies that included patients with hydration status documentation, proven or presumed STEC infection, and some form of HUS that developed. No language restrictions were applied. Two reviewers independently extracted individual study data, including study characteristics, population, and outcomes. Risk of bias was assessed using the Newcastle-Ottawa Scale; strength of evidence was adjudicated using the Grading of Recommendations Assessment, Development, and Evaluation method. Meta-analyses were conducted using random-effects models. Development of HUS, complications (ie, oligoanuric renal failure, involvement of the central nervous system, or death), and interventions (ie, renal replacement therapy). Eight studies comprising 1511 patients (all children) met eligibility criteria. Unpublished data were provided by the authors of 7 published reports. The median risk-of-bias score was 7.5 (range, 6-9). No studies evaluated the effect of hydration during STEC infections on the risk for HUS. A hematocrit value greater than 23% as a measure of hydration status at presentation with HUS was associated with the development of oligoanuric HUS (OR, 2.38 [95% CI, 1.30-4.35]; I2 = 2%), renal replacement therapy (OR, 1.90 [95% CI, 1.25-2.90]; I2 = 17%), and death (OR, 5.13 [95% CI, 1.50-17.57]; I2 = 55%). Compared with putatively hydrated patients, clinically dehydrated patients had an OR of death of 3.71 (95% CI, 1.25-11.03; I2 = 0%). Intravenous fluid administration up to the day of HUS diagnosis was associated with a decreased risk of renal replacement therapy (OR, 0.26 [95% CI, 0.11-0.60]). Two predictors of poor outcomes for STEC-infected children were identified: (1) the lack of intravenous fluid administration prior to establishment of HUS and (2) a higher hematocrit value at presentation. These findings point to an association between dehydration and adverse outcomes for children with HUS.

Monitoring hydration status pre- and post-training among university athletes using urine color and weight loss indicators.

PubMed

Webb, Marquitta C; Salandy, Sinead T; Beckford, Safiya E

2016-01-01

To investigate the hydration status pre- and post-training among university athletes using urine color and weight loss as indicators. Participants were 52 university athletes training for campus games in a developing country. Pre- and post-training urine specimens were compared with a standard urine color scale. Paired t tests were used to compare urine color and difference in body mass pre- and post-training. The mean age of the athletes was 22.87 ± 3.21. A statistically significance difference (p < .01) was observed between pre- (4.31 ± 1.75) and post- (5.67 ± 1.45) training urine color values for males. Hydration status and weight post-training were statistically significantly different both at the level of p < .01. The results suggest that there is a link between urine color and body mass difference among the student athletes tested. Exercise increases hypohydration due to fluid losses, and therefore attention should be given to fluid supplementation and individualization of fluid intake for each athlete.

Dietary intake according to hydration status in 9-10 year-old soccer players.

PubMed

Rodriguez, Lusmar; Azevedp, Ana Raquel; Seabra, André; Padrao, Patrícia; Moreira, Pedro

2016-07-13

Children have an increased risk of voluntary dehydration especially during physical activity which may increase the risk of non-compensating water losses. The aim of this study was to assess the hydration status and its relation to food intake in a children group of soccer players. A sample of 36 boys aged 9-10 years was included in this study; 30 completed a 24 h urine collection. Participants completed a 24 h urine collection; a 24 hours food recall corresponding to the day of urine collection was applied, weight and height were measured and parents/caregivers fi lled a lifestyle and socio-demographic questionnaire. The free water reserve (FWR [ml/24 h] = urine volume [ml/24 h] - obligatory urine volume [ml/24 h]) was used to assess the hydration status. Food and beverage groups were created and models of unconditional logistic regression were fi tted in order to estimate the magnitude of the association between the hydration status and diet. Forty three per cent of participants were classifi ed as at risk of hypohydration. Children who reported a high fruit and vegetables intake (above the median) were at decreased risk of hypohydration (OR = 0.19, 95% CI 0.04-0.94, p = 0.041), compared to children who reported a low fruit and vegetables intake. Almost half of the children were at risk of hypohydration. Our results suggested that water food sources such as fruit and vegetables may contribute to euhydration.

Post-Hoc Study: Intravenous Hydration Treatment in Chinese Patients with High Risk of Contrast-Induced Nephropathy Following Percutaneous Coronary Intervention

PubMed Central

Bei, Weijie; Li, Hualong; Lin, Kaiyang; Wang, Kun; Chen, Shiqun; Guo, Xiaosheng; Liu, Yong; Tan, Ning; Chen, Jiyan; Yang, Xiangtai; Su, Xi; Du, Zhimin; Zeng, Qiutang; Fang, Zhenfei; Wang, Yan; Jiang, Hong; Xiong, Longgen; Hou, Yuqing; Yuan, Yong; Li, Tianfa; Hong, Lang; Wu, Yanqing; Liu, Yin; Lin, Wenhua; Jiang, Tiemin; Fu, Junhua; An, Yi; Yu, Bo; Tian, Ye; Zheng, Yang; Liu, Bin; Yang, Ping; Jiang, Xianyan; Wang, Hao; Qu, Peng; Cui, Lianqun; Li, Xueqi; Qi, Xiaoyong; Ma, Zengcai; Li, Jifu; Zhang, Lili; Liu, Shengquan; Pang, Wenyue; Li, Yibo; Yang, Manguang; Ji, Zheng; Zhao, Pitian; Li, Lu; Ge, Junbo; Jin, Huigen; Pan, Weimin; Song, Yaoming; Li, Jianmei; Xiao, Jianming; Liu, Hanxiong; Tao, Jianhong; Wu, Zhongdong; Tuo, Buxiong; Li, Wei; Xu, Yixian; Zhang, Zhaoqi; Chen, Yundai; Wang, Lefeng; Zhang, Jinying; Wang, Fengling; Jia, Yongping; Wang, Bin; Tang, Fakuan; Tang, Qiang; Wang, Wei; Sun, Yuemin; Su, Weiqing

2017-01-01

Contrast-induced nephropathy (CIN) develops after the injection of iodinated contrast media. This is a post hoc analysis of the data obtained from the TRUST study, which was a prospective, multicentre, observational study conducted to evaluate the safety and tolerability of the contrast medium iopromide in patients undergoing cardiac catheterization from August 2010 to September 2011 in China, conducted to explore the current status, trends and risk predictors of hydration treatment. The status of hydration to prevent CIN in each patient was recorded. Of the total 17,139 patients from the TRUST study (mean age, 60.33 ± 10.38 years), the overall hydration usage was 46.1% in patients undergoing percutaneous coronary intervention (PCI) and 77.4%, 51.7%, and 48.5% in patients with pre-existing renal disease, diabetes mellitus, and hypertension, respectively. The proportion of hydration use increased from 36.5% to 55.5% from August 2010 to September 2011, which was independently associated with risk predictors like older age, pre-existing renal disease, hypertension, diabetes mellitus, prior myocardial infarction, ST segment elevation MI, high contrast dose, multi-vessel disease and reduced LVEF (<45%). Overall, the usage of intravenous hydration treatment for patients with a high risk of CIN following PCI was high in China. PMID:28337989

Relationship between bioimpedance-determined body composition and peritoneal transport in peritoneal dialysis.

PubMed

da Costa, Bernardo M; Del Peso, Gloria; Bajo, Maria Auxiliadora; Carreño, Gilda; Ferreira, Marta; Ferreira, Carina; Selgas, Rafael

2017-05-29

In peritoneal dialysis (PD) patients, body fluid homeostasis is dependent on peritoneal elimination of water and solutes. Patients with less favorable peritoneal transport parameters should be more overhydrated. Despite this, the association between faster transport and overhydration (OH) is weak, and the factors that influence hydration status are still poorly characterized. Modified peritoneal equilibration tests (PET) offer us new parameters that might correlate better with hydration status, like free water transport (FWT). The aim of this study was thus to establish the relationships between new peritoneal transport parameters and body composition parameters estimated by bioimpedance spectroscopy (BIS). Prospective observational study on incident PD patients with a baseline and 1-year follow-up evaluation. 61 patients were included in the baseline evaluation, 19 of whom had a 1-year follow-up evaluation; 67.2% were fluid overloaded. There was a negative correlation between D/P creatinine and FWT (r = -0.598, p = 0.000). The fraction of FWT was negatively correlated with OH (r = -0.302, p = 0.018). Peritoneal protein losses (PPL) were also correlated with OH (r = 0.287, p = 0.028). There were no significant differences in OH according to small-solute transport status or fluid output parameters. After 1 year, we observed a significant worsening of renal function and an improvement in 24-hour ultrafiltration (UF) and hydration status, but we detected no differences in peritoneal transport of water or solutes that could explain these changes. There is a poor relationship between kidney/peritoneal function parameters and body composition parameters. The fraction of FWT and PPL may be underestimated markers of peritoneal health and of its contribution to the hydration status.

Induction of Inducible Nitric Oxide Synthase by Lipopolysaccharide and the Influences of Cell Volume Changes, Stress Hormones and Oxidative Stress on Nitric Oxide Efflux from the Perfused Liver of Air-Breathing Catfish, Heteropneustes fossilis

PubMed Central

Choudhury, Mahua G.; Saha, Nirmalendu

2016-01-01

The air-breathing singhi catfish (Heteropneustes fossilis) is frequently being challenged by bacterial contaminants, and different environmental insults like osmotic, hyper-ammonia, dehydration and oxidative stresses in its natural habitats throughout the year. The main objectives of the present investigation were to determine (a) the possible induction of inducible nitric oxide synthase (iNOS) gene with enhanced production of nitric oxide (NO) by intra-peritoneal injection of lipopolysaccharide (LPS) (a bacterial endotoxin), and (b) to determine the effects of hepatic cell volume changes due to anisotonicity or by infusion of certain metabolites, stress hormones and by induction of oxidative stress on production of NO from the iNOS-induced perfused liver of singhi catfish. Intra-peritoneal injection of LPS led to induction of iNOS gene and localized tissue specific expression of iNOS enzyme with more production and accumulation of NO in different tissues of singhi catfish. Further, changes of hydration status/cell volume, caused either by anisotonicity or by infusion of certain metabolites such as glutamine plus glycine and adenosine, affected the NO production from the perfused liver of iNOS-induced singhi catfish. In general, increase of hydration status/cell swelling due to hypotonicity caused decrease, and decrease of hydration status/cell shrinkage due to hypertonicity caused increase of NO efflux from the perfused liver, thus suggesting that changes in hydration status/cell volume of hepatic cells serve as a potent modulator for regulating the NO production. Significant increase of NO efflux from the perfused liver was also observed while infusing the liver with stress hormones like epinephrine and norepinephrine, accompanied with decrease of hydration status/cell volume of hepatic cells. Further, oxidative stress, caused due to infusion of t-butyl hydroperoxide and hydrogen peroxide separately, in the perfused liver of singhi catfish, resulted in significant increase of NO efflux accompanied with decrease of hydration status/cell volume of hepatic cells. However, the reasons for these cell volume-sensitive changes of NO efflux from the liver of singhi catfish are not fully understood with the available data. Nonetheless, enhanced or decreased production of NO from the perfused liver under osmotic stress, in presence of stress hormones and oxidative stress reflected its potential role in cellular homeostasis and also for better adaptations under environmental challenges. This is the first report of osmosensitive and oxidative stress-induced changes of NO production and efflux from the liver of any teleosts. Further, the level of expression of iNOS in this singhi catfish could also serve as an important indicator to determine the pathological status of the external environment. PMID:26950213

Induction of Inducible Nitric Oxide Synthase by Lipopolysaccharide and the Influences of Cell Volume Changes, Stress Hormones and Oxidative Stress on Nitric Oxide Efflux from the Perfused Liver of Air-Breathing Catfish, Heteropneustes fossilis.

PubMed

Choudhury, Mahua G; Saha, Nirmalendu

2016-01-01

The air-breathing singhi catfish (Heteropneustes fossilis) is frequently being challenged by bacterial contaminants, and different environmental insults like osmotic, hyper-ammonia, dehydration and oxidative stresses in its natural habitats throughout the year. The main objectives of the present investigation were to determine (a) the possible induction of inducible nitric oxide synthase (iNOS) gene with enhanced production of nitric oxide (NO) by intra-peritoneal injection of lipopolysaccharide (LPS) (a bacterial endotoxin), and (b) to determine the effects of hepatic cell volume changes due to anisotonicity or by infusion of certain metabolites, stress hormones and by induction of oxidative stress on production of NO from the iNOS-induced perfused liver of singhi catfish. Intra-peritoneal injection of LPS led to induction of iNOS gene and localized tissue specific expression of iNOS enzyme with more production and accumulation of NO in different tissues of singhi catfish. Further, changes of hydration status/cell volume, caused either by anisotonicity or by infusion of certain metabolites such as glutamine plus glycine and adenosine, affected the NO production from the perfused liver of iNOS-induced singhi catfish. In general, increase of hydration status/cell swelling due to hypotonicity caused decrease, and decrease of hydration status/cell shrinkage due to hypertonicity caused increase of NO efflux from the perfused liver, thus suggesting that changes in hydration status/cell volume of hepatic cells serve as a potent modulator for regulating the NO production. Significant increase of NO efflux from the perfused liver was also observed while infusing the liver with stress hormones like epinephrine and norepinephrine, accompanied with decrease of hydration status/cell volume of hepatic cells. Further, oxidative stress, caused due to infusion of t-butyl hydroperoxide and hydrogen peroxide separately, in the perfused liver of singhi catfish, resulted in significant increase of NO efflux accompanied with decrease of hydration status/cell volume of hepatic cells. However, the reasons for these cell volume-sensitive changes of NO efflux from the liver of singhi catfish are not fully understood with the available data. Nonetheless, enhanced or decreased production of NO from the perfused liver under osmotic stress, in presence of stress hormones and oxidative stress reflected its potential role in cellular homeostasis and also for better adaptations under environmental challenges. This is the first report of osmosensitive and oxidative stress-induced changes of NO production and efflux from the liver of any teleosts. Further, the level of expression of iNOS in this singhi catfish could also serve as an important indicator to determine the pathological status of the external environment.

Assessment of hydration status of elite young male soccer players with different methods and new approach method of substitute urine strip.

PubMed

Ersoy, Nesli; Ersoy, Gulgun; Kutlu, Mehmet

2016-01-01

The purpose of the study is to determine and compare the hydration status with different methods and determine fluid intake, dehydration percentages and sweat rate of 26 young male soccer players (15 ± 1.2 years) before an important competition. More specifically, the study aims at validating the urine strip and advising the players to use it as an easy and practical method. Measurements of urine analysis were taken from the urine sample of the participants before breakfast and conducted for 3 consecutive days before the competition. Hydration status was assessed through analysis of urine color, urine specific gravity (USG) (laboratory, strip, refractometry), and osmolality. The players' dehydration percentages and sweat ratio were calculated. The average values for all samples were 3 ± 1 for color, and 1.021 ± 4 g/cm(3) for USG (laboratory), and 1.021 ± 3 g/cm(3) for USG (strip), and 1.021 ± 4 for USG (refractometry), and 903 ± 133 mOsm/kg for osmolality. USG (strip) was highly correlated with USG (laboratory), USG (refractometry) (r = 0.8; P < 0.01) and osmolality (r = 0.7; P < 0.01), and moderately correlated with urine color (r = 0.4; P < 0.05). The mean dehydration percentage and sweat rate of the soccer players were observed as 0.5 % and 582.3 ± 232.0 mL/h, respectively. We found that youth soccer players are under a slight risk of dehydration under moderate weather conditions. As indicated by the research results, determination of hydration status of athletes must be taken into account more carefully under moderate and hot weather conditions. In addition, hydration methods were compatible with one another as measured in this study.

Hydration and nutritional status in patients on home-dialysis-A single centre study.

PubMed

Li, Janet S C; Chan, John Y H; Tai, Mandy M Y; Wong, So M; Pang, S M; Lam, Fanny Y F; Chu, Carmen H M; Ching, Chris S Y; Wong, Joseph H S; Chak, W L

2018-04-17

Over-hydration (OH) and malnutrition are prevalent among patients on dialysis therapy. The prevalence of OH and malnutrition as well as the risk factors associated with OH and malnutrition in our patients on home peritoneal dialysis (PD) and home haemodialysis (HD) are examined. This was a cross-sectional study. The hydration and nutritional status of the study groups were assessed by a Body Composition Monitor. Patients who were stable on home dialysis therapy for over one year were invited to participate. Univariate and multivariate analyses were performed to identify associated factors and determine the predictors of OH and malnutrition, respectively. Eighty-eight patients (41 PD and 47 home HD) were recruited. A 32.95% of our patients on home dialysis therapy were in OH status. There was a significance difference in the prevalence of hydration status between patients on PD and home HD (p = 0.014), as overhydration was more common in patients on PD than home HD (46.34 vs. 21.28%). Dehydration was more common in patients on home HD than PD (29.79 vs. 9.76%). Male gender, decreasing haemoglobin level and presence of diabetes mellitus (DM) were risk factors of OH on multivariable analysis. There was no significance difference in the prevalence of malnutrition between patients on PD and home HD (p = 0.27). Increasing Fat Tissue Index (FTI), height and patients on PD therapy were at higher risk of malnutrition. OH and malnutrition were prevalent patients on home dialysis therapy. © 2018 European Dialysis and Transplant Nurses Association/European Renal Care Association.

Hydration Status of Patients Dialyzed with Biocompatible Peritoneal Dialysis Fluids

PubMed Central

Lichodziejewska-Niemierko, Monika; Chmielewski, Michał; Dudziak, Maria; Ryta, Alicja; Rutkowski, Bolesław

2016-01-01

♦ Background: Biocompatible fluids for peritoneal dialysis (PD) have been introduced to improve dialysis and patient outcome in end-stage renal disease. However, their impact on hydration status (HS), residual renal function (RRF), and dialysis adequacy has been a matter of debate. The aim of the study was to evaluate the influence of a biocompatible dialysis fluid on the HS of prevalent PD patients. ♦ Methods: The study population consisted of 18 prevalent PD subjects, treated with standard dialysis fluids. At baseline, 9 patients were switched to a biocompatible solution, low in glucose degradation products (GDPs) (Balance; Fresenius Medical Care, Bad Homburg, Germany). Hydration status was assessed through clinical evaluation, laboratory parameters, echocardiography, and bioimpedance spectroscopy over a 24-month observation period. ♦ Results: During the study period, urine volume decreased similarly in both groups. At the end of the evaluation, there were also no differences in clinical (body weight, edema, blood pressure), laboratory (N-terminal pro-brain natriuretic peptide, NTproBNP), or echocardiography determinants of HS. However, dialysis ultrafiltration decreased in the low-GDP group and, at the end of the study, equaled 929 ± 404 mL, compared with 1,317 ± 363 mL in the standard-fluid subjects (p = 0.06). Hydration status assessed by bioimpedance spectroscopy was +3.64 ± 2.08 L in the low-GDP patients and +1.47 ± 1.61 L in the controls (p = 0.03). ♦ Conclusions: The use of a low-GDP biocompatible dialysis fluid was associated with a tendency to overhydration, probably due to diminished ultrafiltration in prevalent PD patients. PMID:26475845

DOE Office of Scientific and Technical Information (OSTI.GOV)

Retamal, María J., E-mail: moretama@uc.cl; Cisternas, Marcelo A.; Seifert, Birger

The recent combination of nanoscale developments with biological molecules for biotechnological research has opened a wide field related to the area of biosensors. In the last years, device manufacturing for medical applications adapted the so-called bottom-up approach, from nanostructures to larger devices. Preparation and characterization of artificial biological membranes is a necessary step for the formation of nano-devices or sensors. In this paper, we describe the formation and characterization of a phospholipid bilayer (dipalmitoylphosphatidylcholine, DPPC) on a mattress of a polysaccharide (Chitosan) that keeps the membrane hydrated. The deposition of Chitosan (∼25 Å) and DPPC (∼60 Å) was performed frommore » the gas phase in high vacuum onto a substrate of Si(100) covered with its native oxide layer. The layer thickness was controlled in situ using Very High Resolution Ellipsometry (VHRE). Raman spectroscopy studies show that neither Chitosan nor DPPC molecules decompose during evaporation. With VHRE and Atomic Force Microscopy we have been able to detect phase transitions in the membrane. The presence of the Chitosan interlayer as a water reservoir is essential for both DPPC bilayer formation and stability, favoring the appearance of phase transitions. Our experiments show that the proposed sample preparation from the gas phase is reproducible and provides a natural environment for the DPPC bilayer. In future work, different Chitosan thicknesses should be studied to achieve a complete and homogeneous interlayer.« less

Water Intake and Hydration Indices in Healthy European Adults: The European Hydration Research Study (EHRS).

PubMed

Malisova, Olga; Athanasatou, Adelais; Pepa, Alex; Husemann, Marlien; Domnik, Kirsten; Braun, Hans; Mora-Rodriguez, Ricardo; Ortega, Juan F; Fernandez-Elias, Valentin E; Kapsokefalou, Maria

2016-04-06

Hydration status is linked with health, wellness, and performance. We evaluated hydration status, water intake, and urine output for seven consecutive days in healthy adults. Volunteers living in Spain, Germany, or Greece (n = 573, 39 ± 12 years (51.1% males), 25.0 ± 4.6 kg/m² BMI) participated in an eight-day study protocol. Total water intake was estimated from seven-day food and drink diaries. Hydration status was measured in urine samples collected over 24 h for seven days and in blood samples collected in fasting state on the mornings of days 1 and 8. Total daily water intake was 2.75 ± 1.01 L, water from beverages 2.10 ± 0.91 L, water from foods 0.66 ± 0.29 L. Urine parameters were: 24 h volume 1.65 ± 0.70 L, 24 h osmolality 631 ± 221 mOsmol/kg Η2Ο, 24 h specific gravity 1.017 ± 0.005, 24 h excretion of sodium 166.9 ± 54.7 mEq, 24 h excretion of potassium 72.4 ± 24.6 mEq, color chart 4.2 ± 1.4. Predictors for urine osmolality were age, country, gender, and BMI. Blood indices were: haemoglobin concentration 14.7 ± 1.7 g/dL, hematocrit 43% ± 4% and serum osmolality 294 ± 9 mOsmol/kg Η2Ο. Daily water intake was higher in summer (2.8 ± 1.02 L) than in winter (2.6 ± 0.98 L) (p = 0.019). Water intake was associated negatively with urine specific gravity, urine color, and urine sodium and potassium concentrations (p < 0.01). Applying urine osmolality cut-offs, approximately 60% of participants were euhydrated and 20% hyperhydrated or dehydrated. Most participants were euhydrated, but a substantial number of people (40%) deviated from a normal hydration level.

In Situ Study of CO2 and H2O Partitioning Between Na-Montmorillonite and Variably Wet Supercritical Carbon Dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loring, John S.; Ilton, Eugene S.; Chen, Jeffrey

Shale formations play fundamental roles in large-scale geologic carbon sequestration (GCS) aimed primarily to mitigate climate change, and in smaller-scale GCS targeted mainly for CO2-enhanced gas recovery operations. In both technologies, CO2 is injected underground as a supercritical fluid (scCO2), where interactions with shale minerals could influence successful GCS implementation. Reactive components of shales include expandable clays, such as montmorillonites and mixed-layer illite/smectite clays. In this work, we used in situ X-ray diffraction (XRD) and in situ infrared (IR) spectroscopy to investigate the swelling/shrinkage and water/CO2 sorption of a pure montmorillonite, Na-SWy-2, when the clay is exposed to variably hydratedmore » scCO2 at 50 °C and 90 bar. Measured interlayer spacings and sorbed water concentrations at varying levels of scCO2 hydration are similar to previously reported values measured in air at ambient pressure over a range of relative humidities. IR spectra show evidence of both water and CO2 intercalation, and variations in peak shapes and positions suggest multiple sorbed types with distinct chemical environments. Based on the intensity of the asymmetric CO stretching band of the CO2 associated with the Na-SWy-2, we observed a significant increase in sorbed CO2 as the clay expands from a 0W to a 1W state, suggesting that water props open the interlayer so that CO2 can enter. However, as the clay transitions from a 1W to a 2W state, CO2 desorbs sharply. These observations were placed in the context of two conceptual models concerning hydration mechanisms for expandable clays and were also discussed in light of recent theoretical studies on CO2-H2O-clay interactions. The swelling/shrinkage of expandable clays could affect solid volume, porosity, and permeability of shales. Consequently, the results from this work could aid predictions of shale caprock integrity in large-scale GCS, as well as methane transmissivity in enhanced gas recovery operations.« less

Quantitative assessment of combination bathing and moisturizing regimens on skin hydration in atopic dermatitis.

PubMed

Chiang, Charles; Eichenfield, Lawrence F

2009-01-01

Standard recommendations for skin care for patients with atopic dermatitis stress the importance of skin hydration and the application of moisturizers. However, objective data to guide recommendations regarding the optimal practice methods of bathing and emollient application are scarce. This study quantified cutaneous hydration status after various combination bathing and moisturizing regimens. Four bathing/moisturizer regimens were evaluated in 10 subjects, five pediatric subjects with atopic dermatitis and five subjects with healthy skin. The regimens consisted of bathing alone without emollient application, bathing and immediate emollient application, bathing and delayed application, and emollient application alone. Each regimen was evaluated in all subjects, utilizing a crossover design. Skin hydration was assessed with standard capacitance measurements. In atopic dermatitis subjects, emollient alone yielded a significantly (p < 0.05) greater mean hydration over 90 minutes (206.2% baseline hydration) than bathing with immediate emollient (141.6%), bathing and delayed emollient (141%), and bathing alone (91.4%). The combination bathing and emollient application regimens demonstrated hydration values at 90 minutes not significantly greater than baseline. Atopic dermatitis subjects had a decreased mean hydration benefit compared with normal skin subjects. Bathing without moisturizer may compromise skin hydration. Bathing followed by moisturizer application provides modest hydration benefits, though less than that of simply applying moisturizer alone.

Hydration Status and Fluid Balance of Elite European Youth Soccer Players during Consecutive Training Sessions.

PubMed

Phillips, Saun M; Sykes, Dave; Gibson, Neil

2014-12-01

The objective of the study was to investigate the hydration status and fluid balance of elite European youth soccer players during three consecutive training sessions. Fourteen males (age 16.9 ± 0.8 years, height 1.79 ± 0.06 m, body mass (BM) 70.6 ± 5.0 kg) had their hydration status assessed from first morning urine samples (baseline) and pre- and post-training using urine specific gravity (USG) measures, and their fluid balance calculated from pre- to post-training BM change, corrected for fluid intake and urine output. Most participants were hypohydrated upon waking (USG >1.020; 77% on days 1 and 3, and 62% on day 2). There was no significant difference between first morning and pre-training USG (p = 0.11) and no influence of training session (p = 0.34) or time (pre- vs. post-training; p = 0.16) on USG. Significant BM loss occurred in sessions 1-3 (0.69 ± 0.22, 0.42 ± 0.25, and 0.38 ± 0.30 kg respectively, p < 0.05). Mean fluid intake in sessions 1-3 was 425 ± 185, 355 ± 161, and 247 ± 157 ml, respectively (p < 0.05). Participants replaced on average 71.3 ± 64.1% (range 0-363.6%) of fluid losses across the three sessions. Body mass loss, fluid intake, and USG measures showed large inter-individual variation. Elite young European soccer players likely wake and present for training hypohydrated, when a USG threshold of 1.020 is applied. When training in a cool environment with ad libitum access to fluid, replacing ~71% of sweat losses results in minimal hypohydration (<1% BM). Consumption of fluid ad libitum throughout training appears to prevent excessive (≥2% BM) dehydration, as advised by current fluid intake guidelines. Current fluid intake guidelines appear applicable for elite European youth soccer players training in a cool environment. Key PointsThe paper demonstrates a notable inter-participant variation in first morning, pre- and post-training hydration status and fluid balance of elite young European soccer players.On average, elite young European soccer players are hypohydrated upon waking and remain hypohydrated before and after training.Elite young European soccer players display varied fluid intake volumes during training, but on average do not consume sufficient fluid to offset fluid losses.Consecutive training sessions do not significantly impair hydration status, suggesting that elite young European soccer players consume sufficient fluid between training to maintain a stable hydration status and prevent excessive (≥2% body mass) dehydrationCurrent fluid intake guidelines appear applicable to this population when training in a cool environment.

Hydration Status and Fluid Balance of Elite European Youth Soccer Players during Consecutive Training Sessions

PubMed Central

Phillips, Saun M.; Sykes, Dave; Gibson, Neil

2014-01-01

The objective of the study was to investigate the hydration status and fluid balance of elite European youth soccer players during three consecutive training sessions. Fourteen males (age 16.9 ± 0.8 years, height 1.79 ± 0.06 m, body mass (BM) 70.6 ± 5.0 kg) had their hydration status assessed from first morning urine samples (baseline) and pre- and post-training using urine specific gravity (USG) measures, and their fluid balance calculated from pre- to post-training BM change, corrected for fluid intake and urine output. Most participants were hypohydrated upon waking (USG >1.020; 77% on days 1 and 3, and 62% on day 2). There was no significant difference between first morning and pre-training USG (p = 0.11) and no influence of training session (p = 0.34) or time (pre- vs. post-training; p = 0.16) on USG. Significant BM loss occurred in sessions 1-3 (0.69 ± 0.22, 0.42 ± 0.25, and 0.38 ± 0.30 kg respectively, p < 0.05). Mean fluid intake in sessions 1-3 was 425 ± 185, 355 ± 161, and 247 ± 157 ml, respectively (p < 0.05). Participants replaced on average 71.3 ± 64.1% (range 0-363.6%) of fluid losses across the three sessions. Body mass loss, fluid intake, and USG measures showed large inter-individual variation. Elite young European soccer players likely wake and present for training hypohydrated, when a USG threshold of 1.020 is applied. When training in a cool environment with ad libitum access to fluid, replacing ~71% of sweat losses results in minimal hypohydration (<1% BM). Consumption of fluid ad libitum throughout training appears to prevent excessive (≥2% BM) dehydration, as advised by current fluid intake guidelines. Current fluid intake guidelines appear applicable for elite European youth soccer players training in a cool environment. Key Points The paper demonstrates a notable inter-participant variation in first morning, pre- and post-training hydration status and fluid balance of elite young European soccer players. On average, elite young European soccer players are hypohydrated upon waking and remain hypohydrated before and after training. Elite young European soccer players display varied fluid intake volumes during training, but on average do not consume sufficient fluid to offset fluid losses. Consecutive training sessions do not significantly impair hydration status, suggesting that elite young European soccer players consume sufficient fluid between training to maintain a stable hydration status and prevent excessive (≥2% body mass) dehydration Current fluid intake guidelines appear applicable to this population when training in a cool environment PMID:25435774

Electrode placement in bioimpedance spectroscopy: evaluation of alternative positioning of electrodes when measuring relative dehydration in athletes.

PubMed

Birkemose, M; Møller, A J; Madsen, M L; Brantlov, S; Sørensen, H; Overgaard, K; Johansen, P

2013-01-01

In order to maintain a homeostatic environment in human cells, the balance between absorption and separation of water must be retained. Imbalance will have consequences on both the cellular and organ levels. Studies performed on athletes have shown coherence between their hydration status and ability to perform. A dehydration of 2-7% of total body weight resulted in a marked decrease in performance. Measurement and monitoring of hydration status may be used to optimize athlete performance. Therefore, in this current study bioimpedance spectroscopy is used to determine the hydration status of athletes. Trials were made to investigate alternative ways of electrode placement when performing bioimpedance spectroscopy in order to measure relative dehydration. A total of 14 test subjects underwent measurements before, during, and after a cycle test of 3×25min. Electrodes where placed to measure body impedance in three different ways: wrist-ankle (recommended method), wrist-wrist, and transthoracic. Furthermore, the relative loss in weight of the subjects during the trial was registered. The study showed no relation between relative weight loss and the wrist-wrist and transthoracic placement method, using bioimpedance spectroscopy to measure relative dehydration. The inability of the method to detect such relative changes in hydration may be due to the bioimpedance spectroscopy technology being extremely sensitive to changes in skin temperature, movement artifacts, thoroughness in placing the electrodes, and the physiological impact on the human body when performing exercise. Therefore, further research into the area of bioimpedance spectroscopy is needed before this methodology can be applied in monitoring active athletes. Hence, a simple weight measurement still seems a more useful way of determining a relative change of hydration in an active setting.

Educational intervention on water intake improves hydration status and enhances exercise performance in athletic youth.

PubMed

Kavouras, S A; Arnaoutis, G; Makrillos, M; Garagouni, C; Nikolaou, E; Chira, O; Ellinikaki, E; Sidossis, L S

2012-10-01

We aimed to evaluate whether an intervention program emphasizing in increased fluid intake can improve exercise performance in children exercising in the heat. Ninety-two young athletes participated in the study (age: 13.8 ± 0.4 years, weight: 54.9 ± 1.5 kg). Thirty-one (boys: 13, girls: 18) children served as the control group (CON) and 61 (boys: 30, girls: 31) as the intervention (INT). Volunteers had free access to fluids. Hydration was assessed on the basis of first morning urine. A series of field tests were used to evaluate exercise performance. All tests occurred outdoors in the morning (mean ambient temperature=28°C). After baseline testing, INT attended a lecture on hydration, and urine color charts were mounted in all bathrooms. Additionally, water accessibility was facilitated in training, dining and resting areas. Hydration status was improved significantly in the INT [USG: pre=1.031 ± 0.09, post=1.023 ± 0.012, P<0.05; urine osmolality (mOsm/kg water): pre=941 ± 30, post=782 ± 34, P<0.05], while no statistically significant changes were found in the CON [USG: pre=1.033 ± 0.011, post=1.032 ± 0.013, P>0.05; urine osmolality (mOsm/kg water) 970 ± 38 vs 961 ± 38, P>0.05]. Performance in an endurance run was improved significantly only in INT (time for 600 m: pre=189 ± 5 s, post=167 ± 4 s, P<0.05). Improving hydration status by ad libitum consumption of water can enhance performance in young children exercising in the heat. © 2011 John Wiley & Sons A/S.

Tipping Point for Expansion of Layered Aluminosilicates in Weakly Polar Solvents: Supercritical CO2.

PubMed

Schaef, Herbert T; Loganathan, Narasimhan; Bowers, Geoffrey M; Kirkpatrick, R James; Yazaydin, A Ozgur; Burton, Sarah D; Hoyt, David W; Thanthiriwatte, K Sahan; Dixon, David A; McGrail, B Peter; Rosso, Kevin M; Ilton, Eugene S; Loring, John S

2017-10-25

Layered aluminosilicates play a dominant role in the mechanical and gas storage properties of the subsurface, are used in diverse industrial applications, and serve as model materials for understanding solvent-ion-support systems. Although expansion in the presence of H 2 O is well-known to be systematically correlated with the hydration free energy of the interlayer cation, particularly in environments dominated by nonpolar solvents (i.e., CO 2 ), uptake into the interlayer is not well-understood. Using novel high-pressure capabilities, we investigated the interaction of dry supercritical CO 2 with Na-, NH 4 -, and Cs-saturated montmorillonite, comparing results with predictions from molecular dynamics simulations. Despite the known trend in H 2 O and that cation solvation energies in CO 2 suggest a stronger interaction with Na, both the NH 4 - and Cs-clays readily absorbed CO 2 and expanded, while the Na-clay did not. The apparent inertness of the Na-clay was not due to kinetics, as experiments seeking a stable expanded state showed that none exists. Molecular dynamics simulations revealed a large endothermicity to CO 2 intercalation in the Na-clay but little or no energy barrier for the NH 4 - and Cs-clays. Indeed, the combination of experiment and theory clearly demonstrate that CO 2 intercalation of Na-montmorillonite clays is prohibited in the absence of H 2 O. Consequently, we have shown for the first time that in the presence of a low dielectric constant, gas swelling depends more on the strength of the interaction between the interlayer cation and aluminosilicate sheets and less on that with solvent. The finding suggests a distinct regime in layered aluminosilicate swelling behavior triggered by low solvent polarizability, with important implications in geomechanics, storage, and retention of volatile gases, and across industrial uses in gelling, decoloring, heterogeneous catalysis, and semipermeable reactive barriers.

Impact of Isotonic Beverage on the Hydration Status of Healthy Chinese Adults in Air-Conditioned Environment

PubMed Central

Siow, Phei Ching; Tan, Wei Shuan Kimberly; Henry, Christiani Jeyakumar

2017-01-01

People living in tropical climates spend much of their time in confined air-conditioned spaces, performing normal daily activities. This study investigated the effect of distilled water (W) or isotonic beverage (IB) on the hydration status in subjects living under these conditions. In a randomized crossover design, forty-nine healthy male subjects either consumed beverage or IB over a period of 8 h (8 h) in a controlled air-conditioned environment. Blood, urine, and saliva samples were collected at baseline and after 8 h. Hydration status was assessed by body mass, urine output, blood and plasma volume, fluid retention, osmolality, electrolyte concentration and salivary flow rate. In the IB group, urine output (1862 ± 86 mL vs. 2104 ± 98 mL) was significantly lower and more fluids were retained (17% ± 3% vs. 7% ± 3%) as compared to W (p < 0.05) after 8 h. IB also resulted in body mass gain (0.14 ± 0.06 kg), while W led to body mass loss (−0.04 ± 0.05 kg) (p = 0.01). A significantly smaller drop in blood volume and lower free water clearance was observed in IB (−1.18% ± 0.43%; 0.55 ± 0.26 mL/min) compared to W (−2.11% ± 0.41%; 1.35 ± 0.24 mL/min) (p < 0.05). IB increased salivary flow rate (0.54 ± 0.05 g/min 0.62 ± 0.04 g/min). In indoor environments, performing routine activities and even without excessive sweating, isotonic beverages may be more effective at retaining fluids and maintaining hydration status by up to 10% compared to distilled water. PMID:28272337

Impact of Isotonic Beverage on the Hydration Status of Healthy Chinese Adults in Air-Conditioned Environment.

PubMed

Siow, Phei Ching; Tan, Wei Shuan Kimberly; Henry, Christiani Jeyakumar

2017-03-07

People living in tropical climates spend much of their time in confined air-conditioned spaces, performing normal daily activities. This study investigated the effect of distilled water (W) or isotonic beverage (IB) on the hydration status in subjects living under these conditions. In a randomized crossover design, forty-nine healthy male subjects either consumed beverage or IB over a period of 8 h (8 h) in a controlled air-conditioned environment. Blood, urine, and saliva samples were collected at baseline and after 8 h. Hydration status was assessed by body mass, urine output, blood and plasma volume, fluid retention, osmolality, electrolyte concentration and salivary flow rate. In the IB group, urine output (1862 ± 86 mL vs. 2104 ± 98 mL) was significantly lower and more fluids were retained (17% ± 3% vs. 7% ± 3%) as compared to W ( p < 0.05) after 8 h. IB also resulted in body mass gain (0.14 ± 0.06 kg), while W led to body mass loss (-0.04 ± 0.05 kg) ( p = 0.01). A significantly smaller drop in blood volume and lower free water clearance was observed in IB (-1.18% ± 0.43%; 0.55 ± 0.26 mL/min) compared to W (-2.11% ± 0.41%; 1.35 ± 0.24 mL/min) ( p < 0.05). IB increased salivary flow rate (0.54 ± 0.05 g/min 0.62 ± 0.04 g/min). In indoor environments, performing routine activities and even without excessive sweating, isotonic beverages may be more effective at retaining fluids and maintaining hydration status by up to 10% compared to distilled water.

No Change in 24-Hour Hydration Status Following a Moderate Increase in Fluid Consumption.

PubMed

Tucker, Matthew A; Adams, J D; Brown, Lemuel A; Ridings, Christian B; Burchfield, Jenna M; Robinson, Forrest B; McDermott, Jamie L; Schreiber, Brett A; Moyen, Nicole E; Washington, Tyrone A; Bermudez, Andrea C; Bennett, Meredith P; Buyckx, Maxime E; Ganio, Matthew S

2016-01-01

To investigate changes in 24-hour hydration status when increasing fluid intake. Thirty-five healthy males (age 23.8 ± 4.7 years; mass 74.0 ± 9.4 kg) were divided into 4 treatment groups for 2 weeks of testing. Volumes of 24-hour fluid ingestion (including water from food) for weeks 1 and 2 was 35 and 40 ml/kg body mass, respectively. Each treatment group was given the same proportion of beverages in each week of testing: water only (n = 10), water + caloric cola (n = 7), water + noncaloric cola (n = 10), or water + caloric cola + noncaloric cola + orange juice (n = 8). Serum osmolality (Sosm), total body water (TBW) via bioelectrical impedance, 24-hour urine osmolality (Uosm), and volume (Uvol) were analyzed at the end of each 24-hour intervention. Independent of treatment, total beverage consumption increased 22% from week 1 to 2 (1685 ± 320 to 2054 ± 363 ml; p < 0.001). Independent of beverage assignment, the increase in fluid consumption between weeks 1 and 2 did not change TBW (43.4 ± 5.2 vs 43.0 ± 4.8 kg), Sosm (292 ± 5 vs 292 ± 5 mOsm/kg), 24-hour Uosm (600 ± 224 vs 571 ± 212 mOsm/kg), or 24-hour Uvol (1569 ± 607 vs 1580 ± 554 ml; all p > 0.05). Regardless of fluid volume or beverage type consumed, measures of 24-hour hydration status did not differ, suggesting that standard measures of hydration status are not sensitive enough to detect a 22% increase in beverage consumption.

Challenges, uncertainties, and issues facing gas production from gas-hydrate deposits

USGS Publications Warehouse

Moridis, G.J.; Collett, T.S.; Pooladi-Darvish, M.; Hancock, S.; Santamarina, C.; Boswel, R.; Kneafsey, T.; Rutqvist, J.; Kowalsky, M.B.; Reagan, M.T.; Sloan, E.D.; Sum, A.K.; Koh, C.A.

2011-01-01

The current paper complements the Moridis et al. (2009) review of the status of the effort toward commercial gas production from hydrates. We aim to describe the concept of the gas-hydrate (GH) petroleum system; to discuss advances, requirements, and suggested practices in GH prospecting and GH deposit characterization; and to review the associated technical, economic, and environmental challenges and uncertainties, which include the following: accurate assessment of producible fractions of the GH resource; development of methods for identifying suitable production targets; sampling of hydrate-bearing sediments (HBS) and sample analysis; analysis and interpretation of geophysical surveys of GH reservoirs; well-testing methods; interpretation of well-testing results; geomechanical and reservoir/well stability concerns; well design, operation, and installation; field operations and extending production beyond sand-dominated GH reservoirs; monitoring production and geomechanical stability; laboratory investigations; fundamental knowledge of hydrate behavior; the economics of commercial gas production from hydrates; and associated environmental concerns. ?? 2011 Society of Petroleum Engineers.

Use of high-frequency ultrasonography for evaluation of skin thickness in relation to hydration status and fluid distribution at various cutaneous sites in dogs.

PubMed

Diana, Alessia; Guglielmini, Carlo; Fracassi, Federico; Pietra, Marco; Balletti, Erika; Cipone, Mario

2008-09-01

To assess the usefulness of high-frequency diagnostic ultrasonography for evaluation of changes of skin thickness in relation to hydration status and fluid distribution at various cutaneous sites in dogs. 10 clinically normal adult dogs (6 males and 4 females) of various breeds. Ultrasonographic examination of the skin was performed before and after hydration via IV administration of an isotonic crystalloid solution (30 mL/kg/h for 30 minutes). A 13-MHz linear-array transducer was used to obtain series of ultrasonographic images at 4 different cutaneous sites (the frontal, sacral, flank, and metatarsal regions). Weight and various clinicopathologic variables (PCV; serum osmolality; and serum total protein, albumin, and sodium concentrations) were determined before and after the infusion. These variables and ultrasonographic measurements of skin thickness before and after hydration were compared. Among the 10 dogs, mean preinfusion skin thickness ranged from 2,211 microm (metatarsal region) to 3,249 microm (sacral region). Compared with preinfusion values, weight was significantly increased, whereas PCV; serum osmolality; and serum total protein, albumin, and sodium concentrations were significantly decreased after infusion. After infusion, dermal echogenicity decreased and skin thickness increased significantly by 21%, 14%, 15%, and 13% in the frontal, sacral, flank, and metatarsal regions, respectively. Cutaneous site and hydration were correlated with cutaneous characteristics and skin thickness determined by use of high-frequency ultrasonography in dogs. Thus, diagnostic ultrasonography may be a useful tool for the noninvasive evaluation of skin hydration in healthy dogs and in dogs with skin edema.

Controllably Designed "Vice-Electrode" Interlayers Harvesting High Performance Lithium Sulfur Batteries.

PubMed

Hao, Youchen; Xiong, Dongbin; Liu, Wen; Fan, Linlin; Li, Dejun; Li, Xifei

2017-11-22

An interlayer has been regarded as a promising mediator to prolong the life span of lithium sulfur batteries because its excellent absorbability to soluble polysulfide efficiently hinders the shuttle effect. Herein, we designed various interlayers and understand the working mechanism of an interlayer for lithium sulfur batteries in detail. It was found that the electrochemical performance of a S electrode for an interlayer located in cathode side is superior to the pristine one without interlayers. Surprisingly, the performance of the S electrode for an interlayer located in anode side is poorer than that of pristine one. For comparison, glass fibers were also studied as a nonconductive interlayer for lithium sulfur batteries. Unlike the two interlayers above, these nonconductive interlayer did displays significant capacity fading because polysulfides were adsorbed onto insulated interlayer. Thus, the nonconductive interlayer function as a "dead zone" upon cycling. Based on our findings, it was for the first time proposed that a controllably optimized interlayer, with electrical conductivity as well as the absorbability of polysulfides, may function as a "vice-electrode" of the anode or cathode upon cycling. Therefore, the cathodic conductive interlayer can enhance lithium sulfur battery performance, and the anodic conductive interlayer may be helpful for the rational design of 3D networks for the protection of lithium metal.

Effect of hydration status on atrial and ventricular volumes and function in healthy adult volunteers.

PubMed

Schantz, Daryl I; Dragulescu, Andreea; Memauri, Brett; Grotenhuis, Heynric B; Seed, Mike; Grosse-Wortmann, Lars

2016-10-01

Assessment of cardiac chamber volumes is a fundamental part of cardiac magnetic resonance (CMR) imaging. While the effects of inter- and intraobserver variability have been studied and have a recognized effect on the comparability of serial cardiac MR imaging studies, the effect of differences in hydration status has not been evaluated. To evaluate the effects of volume administration on cardiac chamber volumes. Thirteen healthy adults underwent a baseline cardiac MR to evaluate cardiac chamber volumes after an overnight fast. They were then given two saline boluses of 10 ml/kg of body weight and the cardiac MR was repeated immediately after each bolus. From the baseline scan to the final scan there was a significant increase in all four cardiac chamber end-diastolic volumes. Right atrial volumes increased 8.0%, from 61.1 to 66.0 ml/m2 (P<0.001), and left atrial volumes increased 10.0%, from 50.0 to 55.0 ml/m2 (P<0.001). Right ventricular volumes increased 6.0%, from 91.1 to 96.5 ml/m2 (P<0.001), and left ventricular volumes increased 3.2%, from 87.0 to 89.8 ml/m2 (P<0.001). Hydration status has a significant effect on the end-diastolic volumes of all cardiac chambers assessed by cardiac MR. Thus, hydration represents a "variable" that should be taken into account when assessing cardiac chamber volumes, especially when performing serial imaging studies in a patient.

Layered double hydroxides as the next generation inorganic anion exchangers: Synthetic methods versus applicability.

PubMed

Chubar, Natalia; Gilmour, Robert; Gerda, Vasyl; Mičušík, Matej; Omastova, Maria; Heister, Katja; Man, Pascal; Fraissard, Jacques; Zaitsev, Vladimir

2017-07-01

This work is the first report that critically reviews the properties of layered double hydroxides (LDHs) on the level of speciation in the context of water treatment application and dynamic adsorption conditions, as well as the first report to associate these properties with the synthetic methods used for LDH preparation. Increasingly stronger maximum allowable concentrations (MAC) of various contaminants in drinking water and liquid foodstuffs require regular upgrades of purification technologies, which might also be useful in the extraction of valuable substances for reuse in accordance with modern sustainability strategies. Adsorption is the main separation technology that allows the selective extraction of target substances from multicomponent solutions. Inorganic anion exchangers arrived in the water business relatively recently to achieve the newly approved standards for arsenic levels in drinking water. LDHs (or hydrotalcites, HTs) are theoretically the best anion exchangers due to their potential to host anions in their interlayer space, which increases their anion removal capacity considerably. This potential of the interlayer space to host additional amounts of target aqueous anions makes the LDHs superior to bulk anion exchanger. The other unique advantage of these layered materials is the flexibility of the chemical composition of the metal oxide-based layers and the interlayer anions. However, until now, this group of "classical" anion exchangers has not found its industrial application in adsorption and catalysis at the industrial scale. To accelerate application of LDHs in water treatment on the industrial scale, the authors critically reviewed recent scientific and technological knowledge on the properties and adsorptive removal of LDHs from water on the fundamental science level. This also includes review of the research tools useful to reveal the adsorption mechanism and the material properties beyond the nanoscale. Further, these properties are considered in association with the synthetic methods by which the LDHs were produced. Special attention is paid to the LDH properties that are particularly relevant to water treatment, such as exchangeability ease of the interlayer anions and the LDH stability at the solid-water interface. Notably, the LDH properties (e.g., rich speciation, hydration, and the exchangeability ease of the interlayer anions with aqueous anions) are considered in the synthetic strategy context applied to the material preparation. One such promising synthetic method has been developed by the authors who supported their opinions by the unpublished data in addition to reviewing the literature. The reviewing approach allowed for establishing regularities between the parameters: the LDH synthetic method-structure/surface/interlayer-removal-suitability for water treatment. Specifically, this approach allowed for a conclusion about either the unsuitability or promising potential of some synthetic methods (or the removal approaches) used for the preparation of LDHs for water purification at larger scales. The overall reviewing approach undertaken by the authors in this work mainly complements the other reviews on LDHs (published over the past seven to eight years) and for the first time compares the properties of these materials beyond the nanoscale. Copyright © 2017 Elsevier B.V. All rights reserved.

Dehydration of Older Patients in Institutional Care and the Home Environment.

PubMed

Lešnik, Amadeus; Piko, Nejc; Železnik, Danica; Bevc, Sebastjan

2017-11-01

Dehydration in older adults is an important clinical problem associated with more comorbidities, longer hospital stays, and higher mortality rates. However, in daily clinical practice, no single gold standard marker of hydration status in older adults is available. The aim of the current study was to define the fluid balance status in older adults residing in institutional care or the home. Four hundred ten patients (192 from institutional care and 218 from home care) 65 and older from the region of lower Styria (Slovenia) were included in the study. Serum osmolality, electrolytes, and blood urea nitrogen to creatinine (BUN:Cr) ratio were used to identify dehydration. Statistically significant differences were found between groups in serum osmolality and BUN:Cr ratio. Moreover, dehydration (defined as increased serum osmolality) was significantly more common in patients in institutional care than home care (51% versus 41.3%, respectively). The results confirm that dehydration is a common clinical problem in older adults, especially in those from institutional care. Although many methods of determining hydration status in older adults have been proposed, no gold standard exists, making hydration evaluation difficult in this population. [Res Gerontol Nurs. 2017; 10(6):260-266.]. Copyright 2017, SLACK Incorporated.

Aortic-Radial Pulse Wave Velocity Ratio in End-stage Renal Disease Patients: Association with Age, Body Tissue Hydration Status, Renal Failure Etiology and Five Years of Hemodialysis.

PubMed

Bia, Daniel; Valtuille, Rodolfo; Galli, Cintia; Wray, Sandra; Armentano, Ricardo; Zócalo, Yanina; Cabrera-Fischer, Edmundo

2017-03-01

The etiology of the end-stage renal disease (ESRD) and the hydration status may be involved in the arterial stiffening process observed in hemodialyzed patients. The ratio between carotid-femoral and carotid-radial pulse wave velocity (PWV ratio) was recently proposed to characterize the patient-specific stiffening process. to analyze: (1) the PWV-ratio in healthy and hemodialyzed subjects, analyzing potential changes associated to etiologies of the ESRD, (2) the PWV-ratio and hydration status using multiple-frequency bioimpedance and, (3) the effects of hemodialysis on PWV-ratio in a 5-year follow-up. PWV-ratio was evaluated in 151 patients differentiated by the pathology determining their ESRD. Total body fluid (TBF), intra and extra cellular fluid (ICF, ECF) were measured in 65 of these patients using bioelectrical-impedance. The association between arterial, hemodynamic or fluid parameters was analyzed. PWV-ratio was evaluated in a group of patients (n = 25) 5 years later (follow-up study). PWV-ratio increased in the ESRD cohort with respect to the control group (1.03 ± 0.23 vs. 1.31 ± 0.37; p < 0.001). PWV-ratio in the diabetic nephropathy group was higher than in all other etiological groups (1.61 ± 0.33; p < 0.05). PWV-ratio was associated with TBF (r = -0.238; p < 0.05), ICF (r = -0.323; p < 0.01), ECF/ICF (r = 0.400; p < 0.001) and ECF/TBF (r = 0.403; p < 0.001). PWV-ratio calculated in ESRD patients in 2007 increased 5 years later (1.14 ± 0.32 vs. 1.43 ± 0.44; p < 0.005). PWV-ratio increased the most in patients with diabetic nephropathy. PWV ratio was significantly associated with age and body hydration status, but not with the blood pressure. PWV-ratio could be considered a blood pressure-independent parameter, associated with the age and hydration status of the patient.

Quality Improvement Initiative to Increase the Use of Nasogastric Hydration in Infants With Bronchiolitis.

PubMed

Srinivasan, Mythili; Pruitt, Cassandra; Casey, Erin; Dhaliwal, Keerat; DeSanto, Cori; Markus, Richard; Rosen, Ayelet

2017-08-01

Intravenous (IV) hydration is used primarily in children with bronchiolitis at our institution. Because nasogastric (NG) hydration can provide better nutrition, the goal of our quality improvement (QI) initiative was to increase the rate of NG hydration in eligible children 1 to 23 months old with bronchiolitis by 20% over 6 months. We used Plan-Do-Study-Act cycles to increase the use of NG hydration in eligible children. Interventions included educational and system-based changes and sharing parental feedback with providers. Chart reviews were performed to identify the rates of NG hydration, which were plotted over time in a statistical process control p chart. The balancing measure was the rate of complications in children with NG versus IV hydration. Two hundred and ninety-three children who were hospitalized with bronchiolitis needed supplemental hydration during the QI initiative (January 2016-April 2016). Ninety-one children were candidates for NG hydration, and 53 (58%) received NG hydration. The rates of NG hydration increased from a baseline of 0% pre-QI bronchiolitis season (January 2015-April 2015) to 58% during the initiative. There was no aspiration and no accidental placement of the NG tube into a child's airway. Nine patients (17%) in the NG group had a progression of disease requiring nil per os status, and 6 of these were transferred to the PICU whereas none of those in the IV group were transferred to the PICU. Post-QI initiative, the majority of nurses (63%) and physicians (95%) stated that they are more likely to consider NG hydration in children with bronchiolitis. We successfully increased the rates of NG hydration in eligible children with bronchiolitis by using educational and system-based interventions. Copyright © 2017 by the American Academy of Pediatrics.

Al/Cu Dissimilar Friction Stir Welding with Ni, Ti, and Zn Foil as the Interlayer for Flow Control, Enhancing Mechanical and Metallurgical Properties

NASA Astrophysics Data System (ADS)

Sahu, Prakash Kumar; Pal, Sukhomay; Pal, Surjya K.

2017-07-01

This research investigates the effects of Ni, Ti, and Zn foil as interlayer, inserted between the faying edges of Al and Cu plates, for controlled intermetallic compound (IMC) formation. The weld tensile strength with Ti and Zn as interlayer is superior to Al base metal strength. This is due to controlled flow of IMCs by diffused Ti interlayer and thin, continuous, and uniform IMC formation in the case of Zn interlayer. Improved flexural stress was observed with interlayer. Weld microhardness varied with different interlayers and purely depends on IMCs present at the indentation point, flow of IMCs, and interlayer hardness. Specimens with interlayer failed at the interface of the nugget and thermomechanical-affected zone (TMAZ) with complete and broken three-dimensional (3-D) grains, indicating transgranular fracture. Phase analysis revealed that Al/Cu IMCs are impeded by Ni and Ti interlayer. The minor binary and ternary IMC phases form adjacent to the interlayer due to diffusion of the material with Al/Cu. Line scan and elemental mapping indicate thin, continuous, and uniform IMCs with enhanced weld metallurgical and mechanical properties for the joints with Zn interlayer. Macrostructural analysis revealed IMC flow variations with and without interlayer. Variation in grain size at different zones is also observed for different interlayers.

Reduction in body temperature using hand cooling versus passive rest after exercise in the heat.

PubMed

Adams, William M; Hosokawa, Yuri; Adams, Elizabeth L; Belval, Luke N; Huggins, Robert A; Casa, Douglas J

2016-11-01

To examine the effects of hydration and hand cooling on lowering body temperature after exercise in the heat. Randomized cross-over design. Nine recreationally active male participants (mean±SD; age, 24±4; height, 177.3±9.9cm; body mass, 76.7±11.6kg; body fat, 14.7±5.8%) completed a bout of treadmill exercise in a hot environment. After completion of exercise, participants were assigned to the following trials for post-exercise cooling: (1) hydrated with passive rest (HY), (2) hydrated with hand cooling on both hands (HY+2HC), (3) dehydrated with passive rest (DY), and (4) dehydrated with hand cooling on both hands (DY+2HC). Within subject differences were assessed using a three-way (Hydration×Condition×Time) repeated measures ANOVA with Tukey's post hoc analysis if significant interactions were found. Irrespective of hydration status, hand cooling on both hands resulted in significantly greater reductions in T REC than passive cooling at minute 20 (0.27°C [0.05, 0.49], ES=2.08, p=0.017) (Fig. 1). The reduction in T REC at minute 18 trended towards statistical significance (0.21°C [.003, .42], ES=1.59, p=0.053). Hydration status alone and when differentiated among modes of cooling showed no differences on changes of T REC or heart rate across all conditions during post exercise recovery (p>0.05). Hand cooling on both hands reduced T REC more than passive cooling, however, the cooling rates observed render hand cooling a poor option for cooling. Greater reductions in T REC after exercise or between bouts of exercise may enhance recovery and subsequent performance. Copyright © 2016 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Influence of various thickness metallic interlayers on opto-electric and mechanical properties of AZO thin films on PET substrates

NASA Astrophysics Data System (ADS)

Chang, R. C.; Li, T. C.; Lin, C. W.

2012-02-01

Various thickness metallic interlayers to improve the opto-electric and mechanical properties of aluminum-doped zinc oxide (AZO) thin films deposited on flexible polyethylene terephtalate (PET) substrates are studied. The effects of the interlayers on the resistance and transmittance of the AZO thin films are discussed. The result shows that the metallic interlayers effectively improve the electric resistance but reduce the optical transmittance of the AZO thin films. These phenomena become more obvious as the interlayer thickness increases. However, the AZO with an aluminum interlayer still behaves an acceptable transmittance. Moreover, mechanical tests indicate that the aluminum interlayer increases the hardness and modulus, and reduce the residual stress of the AZO thin films. In contrast, the silver and copper interlayers decrease the AZO's mechanical properties. Comparing to those without any interlayer, the results show that the best interlayer is the 6 nm thick aluminum film.

Toward production from gas hydrates: Current status, assessment of resources, and simulation-based evaluation of technology and potential

USGS Publications Warehouse

Moridis, G.J.; Collett, T.S.; Boswell, R.; Kurihara, M.; Reagan, M.T.; Koh, C.; Sloan, E.D.

2009-01-01

Gas hydrates (GHs) are a vast energy resource with global distribution in the permafrost and in the oceans. Even if conservative estimates are considered and only a small fraction is recoverable, the sheer size of the resource is so large that it demands evaluation as a potential energy source. In this review paper, we discuss the distribution of natural GH accumulations, the status of the primary international research and development (R&D) programs, and the remaining science and technological challenges facing the commercialization of production. After a brief examination of GH accumulations that are well characterized and appear to be models for future development and gas production, we analyze the role of numerical simulation in the assessment of the hydrate-production potential, identify the data needs for reliable predictions, evaluate the status of knowledge with regard to these needs, discuss knowledge gaps and their impact, and reach the conclusion that the numerical-simulation capabilities are quite advanced and that the related gaps either are not significant or are being addressed. We review the current body of literature relevant to potential productivity from different types of GH deposits and determine that there are consistent indications of a large production potential at high rates across long periods from a wide variety of hydrate deposits. Finally, we identify (a) features, conditions, geology and techniques that are desirable in potential production targets; (b) methods to maximize production; and (c) some of the conditions and characteristics that render certain GH deposits undesirable for production. Copyright ?? 2009 Society of Petroleum Engineers.

Nutritional Strategies Facing an Older Demographic: The Nutrition UP 65 Study Protocol

PubMed Central

2016-01-01

Background The population of Portugal is aging. The lack of data on older adults’ nutritional status and the lack of nutrition knowledge amongst health professionals, caregivers, and older adults themselves, remains a challenge. Objective The Nutrition UP 65 study aims to reduce nutritional inequalities in the older Portuguese adult population and improve knowledge regarding older Portuguese adults’ nutritional status, specifically relating to undernutrition, obesity, sarcopenia, frailty, hydration, sodium, and vitamin D statuses. Methods A representative sample of older Portuguese adults was selected. Sociodemographic, lifestyle, anthropometric, functional, and clinical data were collected. Sodium excretion, hydration, and vitamin D statuses were assessed. Results Data collection (n=1500) took place between December, 2015 and June, 2016. Results will be disseminated in national and international scientific journals, and via Portuguese media. Conclusions Nutrition UP 65 results will provide evidence for the design and implementation of effective preventive public health strategies regarding the elderly. These insights may represent relevant health gains and costs savings. PMID:27628097

Formation of intercalation compound of kaolinite-glycine via displacing guest water by glycine.

PubMed

Zheng, Wan; Zhou, Jing; Zhang, Zhenqian; Chen, Likun; Zhang, Zhongfei; Li, Yong; Ma, Ning; Du, Piyi

2014-10-15

The kaolinite-glycine intercalation compound was successfully formed by displacing intercalated guest water molecules in kaolinite hydrate as a precursor. The microstructure of the compound was characterized by X-ray diffraction, Fourier Transform Infrared Spectroscopy and Scanning Electron Microscope. Results show that glycine can only be intercalated into hydrated kaolinite to form glycine-kaolinite by utilizing water molecules as a transition phase. The intercalated glycine molecules were squeezed partially into the ditrigonal holes in the silicate layer, resulting in the interlayer distance of kaolinite reaching 1.03nm. The proper intercalation temperature range was between 20°C and 80°C. An intercalation time of 24h or above was necessary to ensure the complete formation of kaolinite-glycine. The highest intercalation degree of about 84% appeared when the system was reacted at the temperature of 80°C for 48h. There were two activation energies for the intercalation of glycine into kaolinite, one being 21kJ/mol within the temperature range of 20-65°C and the other 5.8kJ/mol between 65°C and 80°C. The intercalation degree (N) and intercalation velocity (v) of as a function of intercalation time (t) can be empirically expressed as N=-79.35e(-)(t)(/14.8)+80.1 and v=5.37e(-)(t)(/14.8), respectively. Copyright © 2014 Elsevier Inc. All rights reserved.

Elevated Serum Osmolality and Total Water Deficit Indicate Impaired Hydration Status in Long Term Care Residents Regardless of Low or High Body Mass Index

PubMed Central

Marra, Melissa Ventura; Hudson, Abbie L.; Hollingsworth, Emily K.; Long, Emily; Kuertz, Britt; Simmons, Sandra F.; Shotwell, Matthew S.; Silver, Heidi J.

2016-01-01

Background Dehydration is typically associated with underweight and malnutrition in long term care (LTC) settings. Evidence is lacking regarding the influence of the rising prevalence of overweight and obesity on risk factors, prevalence and presentation of dehydration. Objective The aim of this study was to objectively assess hydration status and the adequacy of total water intake, and determine relationships between hydration status, total water intake, and body mass index (BMI) in LTC residents. Design A cross-sectional analysis of baseline data was performed. Participants and setting Baseline data from 247 subjects recruited from 8 community-based LTC facilities participating in two randomized trials comparing nutrient and cost efficacy of between-meal snacks versus oral nutrition supplements. Main outcomes Hydration status was assessed by serum osmolality concentration and total water intakes were quantified by weighed food, beverage, water and oral nutrition supplement (ONS) intake. Statistical analyses Simple and multiple linear regression methods were applied. Results Forty-nine (38.3%) subjects were dehydrated (>300 mOsm/kg) and another 39 (30.5%) had impending dehydration (295–300 mOsm/kg). The variance in serum osmolality was significantly accounted for by blood urea nitrogen level, mental status score, and having diabetes (R2 = 0.46, P < 0.001). Total water intake averaged 1147.2 ± 433.1 mL/d. Thus, 96–100% subjects did not meet estimated requirements, with a deficit range of 700–1800 mL/d. The variance in total water intake was significantly accounted for by type of liquid beverages (thin vs thick), type of ONS, total energy intake, total activities of daily living dependence, sex and BMI (R2 = 0.56, P < 0.001). Conclusions Dehydration and inadequate total water intake is prevalent in LTC residents across all BMI categories. Type of liquid beverages, type of ONS, and type of between-meal snacks are factors that could be targeted for nutrition interventions designed to prevent or reverse dehydration. PMID:27126154

Elevated Serum Osmolality and Total Water Deficit Indicate Impaired Hydration Status in Residents of Long-Term Care Facilities Regardless of Low or High Body Mass Index.

PubMed

Marra, Melissa Ventura; Simmons, Sandra F; Shotwell, Matthew S; Hudson, Abbie; Hollingsworth, Emily K; Long, Emily; Kuertz, Brittany; Silver, Heidi J

2016-05-01

Dehydration is typically associated with underweight and malnutrition in long-term care (LTC) settings. Evidence is lacking regarding the influence of the rising prevalence of overweight and obesity on risk factors, prevalence, and presentation of dehydration. The aim of this study was to objectively assess hydration status and the adequacy of total water intake, and determine relationships between hydration status, total water intake, and body mass index (BMI) in LTC residents. A cross-sectional analysis of baseline data was performed. Baseline data from 247 subjects recruited from eight community-based LTC facilities participating in two randomized trials comparing nutrient and cost-efficacy of between-meal snacks vs oral nutrition supplements (ONS). Hydration status was assessed by serum osmolality concentration and total water intakes were quantified by weighed food, beverage, water, and ONS intake. Simple and multiple linear regression methods were applied. Forty-nine (38.3%) subjects were dehydrated (>300 mOsm/kg) and another 39 (30.5%) had impending dehydration (295 to 300 mOsm/kg). The variance in serum osmolality was significantly accounted for by blood urea nitrogen level, mental status score, and having diabetes (R(2)=0.46; P<0.001). Total water intake averaged 1,147.2±433.1 mL/day. Thus, 96% to 100% of subjects did not meet estimated requirements, with a deficit range of 700 to 1,800 mL/day. The variance in total water intake was significantly accounted for by type of liquid beverages (thin vs thick), type of ONS, total energy intake, total activities of daily living dependence, sex, and BMI (R(2)=0.56; P<0.001). Dehydration and inadequate total water intake is prevalent in LTC residents across all BMI categories. Type of liquid beverages, type of ONS, and type of between-meal snacks are factors that could be targeted for nutrition interventions designed to prevent or reverse dehydration. Copyright © 2016 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Hydration in advanced cancer: can bioelectrical impedance analysis improve the evidence base? A systematic review of the literature.

PubMed

Nwosu, Amara Callistus; Mayland, Catriona R; Mason, Stephen R; Khodabukus, Andrew F; Varro, Andrea; Ellershaw, John E

2013-09-01

Decisions surrounding the administration of clinically assisted hydration to patients dying of cancer can be challenging because of the limited understanding of hydration in advanced cancer and a lack of evidence to guide health care professionals. Bioelectrical impedance analysis (BIA) has been used to assess hydration in various patient groupings, but evidence for its use in advanced cancer is limited. To critically appraise existing methods of hydration status assessment in advanced cancer and review the potential for BIA to assess hydration in advanced cancer. Searches were carried out in four electronic databases. A hand search of selected peer-reviewed journals and conference abstracts also was conducted. Studies reporting (de)hydration assessment (physical examination, biochemical measures, symptom assessment, and BIA) in patients with advanced cancer were included. The results highlight how clinical examination and biochemical tests are standard methods of assessing hydration, but limitations exist with these methods in advanced cancer. Furthermore, there is disagreement over the evidence for some commonly associated symptoms with dehydration in cancer. Although there are limitations with using BIA alone to assess hydration in advanced cancer, analysis of BIA raw measurements through the method of bioelectrical impedance vector analysis may have a role in this population. The benefits and burdens of providing clinically assisted hydration to patients dying of cancer are unclear. Bioelectrical impedance vector analysis shows promise as a hydration assessment tool but requires further study in advanced cancer. Innovative methodologies for research are required to add to the evidence base and ultimately improve the care for the dying. Copyright © 2013 U.S. Cancer Pain Relief Committee. Published by Elsevier Inc. All rights reserved.

Mobile Technology Application for Improved Urine Concentration Measurement Pilot Study.

PubMed

Walawender, Laura; Patterson, Jeremy; Strouse, Robert; Ketz, John; Saxena, Vijay; Alexy, Emily; Schwaderer, Andrew

2018-01-01

Objectives: Low hydration has a deleterious effect on many conditions. In the absence of a urine concentrating defect, urine concentration is a marker of hydration status. However, markers to evaluate hydration status have not been well studied in children. The objectives of this paper are to compare measures of thirst and urine concentration in children and to develop a novel mobile technology application to measure urine concentration. Study Design: Children age 12-17 years were selected ( n = 21) for this pilot study. Thirst perception, specific gravity (automated dipstick analysis and refractometer), and urine color scale results were correlated to urine osmolality. The technology department developed a mobile technology camera application to measure light penetrance into urine which was tested on 25 random anonymized urine samples. Results: The patients' thirst perception and color scale as well as two researchers color scale did not significantly correlate with osmolality. Correlation between osmolality and hydration markers resulted in the following Pearson coefficients: SG automated dipstick, 0.61 ( P 0.003); SG refractometer, 0.98 ( P < 0.0001); urine color scale (patient), 0.37 ( P 0.10), and light penetrance, -0.77 ( P < 0.0001). The correlation of light penetrance with osmolality was stronger than all measures except SG by refractometer and osmolality. Conclusion: The mobile technology application may be a more accurate tool for urine concentration measurement than specific gravity by automated dipstick, subjective thirst, and urine color scale, but lags behind specific gravity measured by refractometer. The mobile technology application is a step toward patient oriented hydration strategies.

Heat and hydration status: Predictors of repeated measures of urine specific gravity among Tsimane' adults in the Bolivian Amazon.

PubMed

Rosinger, Asher

2015-12-01

Hydration status is critical to physiological and cognitive health, yet it is unclear how populations living in hot-humid environments experiencing lifestyle transitions manage this underexplored facet of heat adaptation. This study assesses the predictors of repeated measures of hydration status for adults from two villages (close and distant from a market town) in the Bolivian Amazon. Interviews and focal follows were conducted with 36 Tsimane' (50% male). Urine samples, temperature, activity levels, and anthropometrics were measured pre-interview and post-follow and yielded a small panel (72 observations). Urine samples were analyzed for urine specific gravity (USG), a biomarker of hydration, with a refractometer. The mean USG was 1.020 g/ml (SD ± 0.008) with men (1.022 ± 0.008) slightly more dehydrated than women (1.018 ± 0.007). Using 1.020 as the criteria for clinical dehydration, 42% of the participants were dehydrated at both intervals and 21% were extremely dehydrated. Controlling for activity level, village membership, and covariates in random-effects linear regression models, each degree centigrade increase was associated with a USG increase of 0.0008 g/ml (P = 0.000). Adults from the village closer to the market town had significantly higher USG (B = 0.0041; P = 0.04) than those in the distant village. Dehydration was predicted to occur at 29°C, just above the thermoneutral range, and extreme dehydration at 37°C. These findings suggest that hotter temperatures coupled with lifestyle transitions may create conditions that increase vulnerability to dehydration among rural populations through landscape modifications and diet changes. © 2015 Wiley Periodicals, Inc.

Monitoring Body Water Balance in Pregnant and Nursing Women: The Validity of Urine Color.

PubMed

McKenzie, Amy L; Armstrong, Lawrence E

2017-01-01

Urine osmolality (UOSM) reflects the renal regulation of excess fluid or deficit fluid, and therefore, serves as a marker of hydration status. Little is known about monitoring hydration in pregnant and lactating women despite significant physiological challenges to body water balance during that time. Therefore, we designed a study to assess if urine color (UCOL), an inexpensive and practical method, was a valid means of assessing urine concentration. Twenty-four hour UCOL was significantly correlated with 24 h UOSM in all women: pregnant, lactating, and control (r = 0.61-0.84, all p < 0.001). Utilizing a receiver operating characteristic statistical analysis, we found that 24 h and single sample UCOL had excellent diagnostic accuracy for identifying UOSM ≥500 mOsm·kg-1 in all women (area under the curve = 0.68-0.95, p < 0.001-0.46), and the UCOL that reflected this cut off was ≥4 on the UCOL chart. Therefore, UCOL is a valid marker of urine concentration and ultimately hydration status in pregnant, lactating, and non-pregnant, non-lactating women. For pregnant, lactating, and control women, the UCOL chart is a valid tool that can be used to monitor urine concentration in a single sample or over the course of the day via a 24 h sample. Key Message: Women who present with a UCOL of 4 or more likely have a UOSM ≥500 mOsm·kg-1. Given the positive health benefits associated with UOSM <500 mOsm·kg-1, women should aim for a 1, 2, or 3 on the UCOL chart. If a UCOL of ≥4 is observed, women should consider increasing fluid consumption to improve hydration status. © 2017 The Author(s) Published by S. Karger AG, Basel.

Hydration status regulates sodium flux and inflammatory pathways through epithelial sodium channel (ENaC) in the skin.

PubMed

Xu, Wei; Hong, Seok Jong; Zeitchek, Michael; Cooper, Garry; Jia, Shengxian; Xie, Ping; Qureshi, Hannan A; Zhong, Aimei; Porterfield, Marshall D; Galiano, Robert D; Surmeier, D James; Mustoe, Thomas A

2015-03-01

Although it is known that the inflammatory response that results from disruption of epithelial barrier function after injury results in excessive scarring, the upstream signals remain unknown. It has also been observed that epithelial disruption results in reduced hydration status and that the use of occlusive dressings that prevent water loss from wounds decreases scar formation. We hypothesized that hydration status changes sodium homeostasis and induces sodium flux in keratinocytes, which result in activation of pathways responsible for keratinocyte-fibroblast signaling and ultimately lead to activation of fibroblasts. Here, we demonstrate that perturbations in epithelial barrier function lead to increased sodium flux in keratinocytes. We identified that sodium flux in keratinocytes is mediated by epithelial sodium channels (ENaCs) and causes increased secretion of proinflammatory cytokines, which activate fibroblast via the cyclooxygenase 2 (COX-2)/prostaglandin E2 (PGE2) pathway. Similar changes in signal transduction and sodium flux occur by increased sodium concentration, which simulates reduced hydration, in the media in epithelial cultures or human ex vivo skin cultures. Blockade of ENaC, prostaglandin synthesis, or PGE2 receptors all reduce markers of fibroblast activation and collagen synthesis. In addition, employing a validated in vivo excessive scar model in the rabbit ear, we demonstrate that utilization of either an ENaC blocker or a COX-2 inhibitor results in a marked reduction in scarring. Other experiments demonstrate that the activation of COX-2 in response to increased sodium flux is mediated through the PIK3/Akt pathway. Our results indicate that ENaC responds to small changes in sodium concentration with inflammatory mediators and suggest that the ENaC pathway is a potential target for a strategy to prevent fibrosis.

Feasibility Study on a Microwave-Based Sensor for Measuring Hydration Level Using Human Skin Models

PubMed Central

Brendtke, Rico; Wiehl, Michael; Groeber, Florian; Schwarz, Thomas; Walles, Heike; Hansmann, Jan

2016-01-01

Tissue dehydration results in three major types of exsiccosis—hyper-, hypo-, or isonatraemia. All three types entail alterations of salt concentrations leading to impaired biochemical processes, and can finally cause severe morbidity. The aim of our study was to demonstrate the feasibility of a microwave-based sensor technology for the non-invasive measurement of the hydration status. Electromagnetic waves at high frequencies interact with molecules, especially water. Hence, if a sample contains free water molecules, this can be detected in a reflected microwave signal. To develop the sensor system, human three-dimensional skin equivalents were instituted as a standardized test platform mimicking reproducible exsiccosis scenarios. Therefore, skin equivalents with a specific hydration and density of matrix components were generated and microwave measurements were performed. Hydration-specific spectra allowed deriving the hydration state of the skin models. A further advantage of the skin equivalents was the characterization of the impact of distinct skin components on the measured signals to investigate mechanisms of signal generation. The results demonstrate the feasibility of a non-invasive microwave-based hydration sensor technology. The sensor bears potential to be integrated in a wearable medical device for personal health monitoring. PMID:27046226

Feasibility Study on a Microwave-Based Sensor for Measuring Hydration Level Using Human Skin Models.

PubMed

Brendtke, Rico; Wiehl, Michael; Groeber, Florian; Schwarz, Thomas; Walles, Heike; Hansmann, Jan

2016-01-01

Tissue dehydration results in three major types of exsiccosis--hyper-, hypo-, or isonatraemia. All three types entail alterations of salt concentrations leading to impaired biochemical processes, and can finally cause severe morbidity. The aim of our study was to demonstrate the feasibility of a microwave-based sensor technology for the non-invasive measurement of the hydration status. Electromagnetic waves at high frequencies interact with molecules, especially water. Hence, if a sample contains free water molecules, this can be detected in a reflected microwave signal. To develop the sensor system, human three-dimensional skin equivalents were instituted as a standardized test platform mimicking reproducible exsiccosis scenarios. Therefore, skin equivalents with a specific hydration and density of matrix components were generated and microwave measurements were performed. Hydration-specific spectra allowed deriving the hydration state of the skin models. A further advantage of the skin equivalents was the characterization of the impact of distinct skin components on the measured signals to investigate mechanisms of signal generation. The results demonstrate the feasibility of a non-invasive microwave-based hydration sensor technology. The sensor bears potential to be integrated in a wearable medical device for personal health monitoring.

Hydration status in adolescent runners: pre and post training

NASA Astrophysics Data System (ADS)

Ashadi, K.; Mirza, D. N.; Siantoro, G.

2018-01-01

The adequacy of body fluids is important for athletes in supporting performance. The purpose of this research was to determine the hydration status of athletes before and after training. The study was a qualitative descriptive by using random sampling. All athletes were trained for approximately 60 minutes. And they were asked to analyze their body fluid pattern routinely. Data were obtained through urine color measurement. The urinary was taken at pre and post training and was immediately assessed in the afternoon. Based on pre-training urine samples, a mean of urine color scale was 3.1 point. It meant that only 31.2% of the athletes were in dehydrated condition. However, after exercising, urine color index showed scale 4.1. And 62.5% of the athletes experienced dehydration. The results showed that there was a significant change in hydration level before and after training. It can be concluded that training for a long time increases the risk of dehydration. It is important for athletes to meet the needs of body fluids in order to avoid functional impairment in the body during sports activities.

Low-Frequency Shear and Layer-Breathing Modes in Raman Scattering of Two-Dimensional Materials.

PubMed

Liang, Liangbo; Zhang, Jun; Sumpter, Bobby G; Tan, Qing-Hai; Tan, Ping-Heng; Meunier, Vincent

2017-12-26

Ever since the isolation of single-layer graphene in 2004, two-dimensional layered structures have been among the most extensively studied classes of materials. To date, the pool of two-dimensional materials (2DMs) continues to grow at an accelerated pace and already covers an extensive range of fascinating and technologically relevant properties. An array of experimental techniques have been developed and used to characterize and understand these properties. In particular, Raman spectroscopy has proven to be a key experimental technique, thanks to its capability to identify minute structural and electronic effects in nondestructive measurements. While high-frequency (HF) intralayer Raman modes have been extensively employed for 2DMs, recent experimental and theoretical progress has demonstrated that low-frequency (LF) interlayer Raman modes are more effective at determining layer numbers and stacking configurations and provide a unique opportunity to study interlayer coupling. These advantages are due to 2DMs' unique interlayer vibration patterns where each layer behaves as an almost rigidly moving object with restoring forces corresponding to weak interlayer interactions. Compared to HF Raman modes, the relatively small attention originally devoted to LF Raman modes is largely due to their weaker signal and their proximity to the strong Rayleigh line background, which previously made their detection challenging. Recent progress in Raman spectroscopy with technical and hardware upgrades now makes it possible to probe LF modes with a standard single-stage Raman system and has proven crucial to characterize and understand properties of 2DMs. Here, we present a comprehensive and forward-looking review on the current status of exploiting LF Raman modes of 2DMs from both experimental and theoretical perspectives, revealing the fundamental physics and technological significance of LF Raman modes in advancing the field of 2DMs. We review a broad array of materials, with varying thickness and stacking configurations, discuss the effect of in-plane anisotropy, and present a generalized linear chain model and interlayer bond polarizability model to rationalize the experimental findings. We also discuss the instrumental improvements of Raman spectroscopy to enhance and separate LF Raman signals from the Rayleigh line. Finally, we highlight the opportunities and challenges ahead in this fast-developing field.

Multi-step oxidations catalyzed by cytochrome P450 enzymes: Processive vs. distributive kinetics and the issue of carbonyl oxidation in chemical mechanisms

PubMed Central

Guengerich, F. Peter; Sohl, Christal D.; Chowdhury, Goutam

2010-01-01

Catalysis of sequential oxidation reactions is not unusual in cytochrome P450 (P450) reactions, not only in steroid metabolism but also with many xenobiotics. One issue is how processive/distributive these reactions are, i.e. how much do the “intermediate” products dissociate. Our work with human P450s 2E1, 2A6, and 19A1 on this subject has revealed a mixture of systems, surprisingly with a more distributive mechanism with an endogenous substrate (P450 19A1) than for some xenobiotics (P450s 2E1, 2A6). One aspect of this research involves carbonyl intermediates, and the choice of catalytic mechanism is linked to the hydration state of the aldehyde. The non-enzymatic rates of hydration and dehydration of carbonyls are not rapid and whether P450s catalyze the reversible hydration is unknown. If carbonyl hydration and dehydration are slow, the mechanism may be set by the carbonyl hydration status. PMID:20804723

The role of obesity in the relation between total water intake and urine osmolality in US adults, 2009-2012.

PubMed

Rosinger, Asher Y; Lawman, Hannah G; Akinbami, Lara J; Ogden, Cynthia L

2016-12-01

Adequate water intake is critical to physiologic and cognitive functioning. Although water requirements increase with body size, it remains unclear whether weight status modifies the relation between water intake and hydration status. We examined how the association between water intake and urine osmolality, which is a hydration biomarker, varied by weight status. NHANES cross-sectional data (2009-2012) were analyzed in 9601 nonpregnant adults aged ≥20 y who did not have kidney failure. Weight status was categorized with the use of body mass index on the basis of measured height and weight (underweight or normal weight, overweight, and obesity). Urine osmolality was determined with the use of freezing-point depression osmometry. Hypohydration was classified according to the following age-dependent formula: ≥831 mOsm/kg - [3.4 × (age - 20 y)]. Total water intake was determined with the use of a 24-h dietary recall and was dichotomized as adequate or low on the basis of the Institute of Medicine's adequate intake recommendations for men and women (men: ≥3.7 or <3.7 L; nonlactating women: ≥2.7 or <2.7 L; lactating women: ≥3.8 or <3.8 L for adequate or low intakes, respectively). We tested interactions and conducted linear and log-binomial regressions. Total water intake (P = 0.002), urine osmolality (P < 0.001), and hypohydration prevalence (P < 0.001) all increased with higher weight status. Interactions between weight status and water intake status were significant in linear (P = 0.005) and log-binomial (P = 0.015) models, which were then stratified. The prevalence ratio of hypohydration between subjects with adequate water intake and those with low water intake was 0.56 (95% CI: 0.43, 0.73) in adults who were underweight or normal weight, 0.67 (95% CI: 0.57, 0.79) in adults who were overweight, and 0.78 (95% CI: 0.70, 0.88) in adults who were obese. On a population level, obesity modifies the association between water intake and hydration status. © 2016 American Society for Nutrition.

Effect of Fluid Intake on Hydration Status and Skin Barrier Characteristics in Geriatric Patients: An Explorative Study.

PubMed

Akdeniz, Merve; Boeing, Heiner; Müller-Werdan, Ursula; Aykac, Volkan; Steffen, Annika; Schell, Mareike; Blume-Peytavi, Ulrike; Kottner, Jan

2018-01-01

Inadequate fluid intake is assumed to be a trigger of water-loss dehydration, which is a major health risk in aged and geriatric populations. Thus, there is a need to search for easy to use diagnostic tests to identify dehydration. Our overall aim was to investigate whether skin barrier parameters could be used for predicting fluid intake and/or hydration status in geriatric patients. An explorative observational comparative study was conducted in a geriatric hospital including patients aged 65 years and older. We measured 3-day fluid intake, skin barrier parameters, Overall Dry Skin Score, serum osmolality, cognitive and functional health, and medications. Forty patients were included (mean age 78.45 years and 65% women) with a mean fluid intake of 1,747 mL/day. 20% of the patients were dehydrated and 22.5% had an impending dehydration according to serum osmolality. Multivariate analysis suggested that skin surface pH and epidermal hydration at the face were associated with fluid intake. Serum osmolality was associated with epidermal hydration at the leg and skin surface pH at the face. Fluid intake was not correlated with serum osmolality. Diuretics were associated with high serum osmolality. Approximately half of the patients were diagnosed as being dehydrated according to osmolality, which is the current reference standard. However, there was no association with fluid intake, questioning the clinical relevance of this measure. Results indicate that single skin barrier parameters are poor markers for fluid intake or osmolality. Epidermal hydration might play a role but most probably in combination with other tests. © 2018 S. Karger AG, Basel.

Educational strategies used in increasing fluid intake and enhancing hydration status in field hockey players preparing for competition in a hot and humid environment: a case study.

PubMed

Dabinett, J A; Reid, K; James, N

2001-09-01

The purpose of the present study was to develop a hydration strategy for use by female English field hockey players at the 1998 Commonwealth Games in Malaysia. An additional aim was to initiate the process of acclimation. Fifteen elite players, mean age (+/-SEM) 24.1 +/- 1.19 years, height 1.67 +/- 0.01 m, and body mass 62.8 +/- 1.76 kg, took part in a 5-day training camp immediately prior to departure for the Games. In order to develop the hydration strategy, training took place under similar environmental conditions to those to be experienced in Malaysia (i.e., 32 degrees C, 80% humidity). Acclimation training consisted of 30-50 min of either continuous, low intensity cycling or high intensity intermittent cycling, which more closely replicated the pattern of activity in field hockey. Body mass measures taken each morning, and pre and post training, together with urine color measures, were used to assess hydration status. Pre-loading with up to 1 L of a 3% carbohydrate-electrolyte solution or water immediately prior to acclimation training, as well as regular drinks throughout, ensured that players avoided significant dehydration, with percent body mass changes ranging from -0.34% to +4.24% post training. Furthermore, the protocol used was sufficient to initiate the process of acclimation as demonstrated by a significant reduction in exercising heart rate and core temperature at all time points by days 4 and 5. In conclusion, although labor intensive and time consuming, the camp was successful in developing a hydration strategy that players were able to utilize once at the Games.

Effects of carbohydrate-hydration strategies on glucose metabolism, sprint performance and hydration during a soccer match simulation in recreational players.

PubMed

Kingsley, Michael; Penas-Ruiz, Carlos; Terry, Chris; Russell, Mark

2014-03-01

This study compared the effects of three carbohydrate-hydration strategies on blood glucose concentration, exercise performance and hydration status throughout simulated soccer match-play. A randomized, double-blind and cross-over study design was employed. After familiarization, 14 recreational soccer players completed the soccer match simulation on three separate occasions. Participants consumed equal volumes of 9.6% carbohydrate-caffeine-electrolyte (∼ 6 mg/kg BW caffeine) solution with carbohydrate-electrolyte gels (H-CHO), 5.6% carbohydrate-electrolyte solution with electrolyte gels (CHO) or electrolyte solution and electrolyte gels (PL). Blood samples were taken at rest, immediately before exercise and every 15 min during exercise (first half: 15, 30, 45 min; second half: 60, 75, 90 min). Supplementation influenced blood glucose concentration (time × treatment interaction: p<0.001); however, none of the supplementation regimes were effective in preventing a drop in blood glucose at 60 min. Mean sprint speed was 3 ± 1% faster in H-CHO when compared with PL (treatment: p=0.047). Supplementation caused a 2.3 ± 0.5% increase in plasma osmolality in H-CHO (p<0.001) without change in CHO or PL. Similarly, mean sodium concentrations were 2.1 ± 0.4% higher in H-CHO when compared with PL (p=0.006). Combining high carbohydrate availability with caffeine resulted in improved sprint performance and elevated blood glucose concentrations throughout the first half and at 90 min of exercise; however, this supplementation strategy negatively influenced hydration status when compared with 5.6% carbohydrate-electrolyte and electrolyte solutions. Copyright © 2013 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

The effect of mineral-based alkaline water on hydration status and the metabolic response to short-term anaerobic exercise.

PubMed

Chycki, Jakub; Zając, Tomasz; Maszczyk, Adam; Kurylas, Anna

2017-09-01

Previously it was demonstrated that mineralization and alkalization properties of mineral water are important factors influencing acid-base balance and hydration in athletes. The purpose of this study was to investigate the effects of drinking different types of water on urine pH, specific urine gravity, and post-exercise lactate utilization in response to strenuous exercise. Thirty-six male soccer players were divided into three intervention groups, consuming around 4.0 l/day of different types of water for 7 days: HM (n=12; highly mineralized water), LM (n=12; low mineralized water), and CON (n=12; table water). The athletes performed an exercise protocol on two occasions (before and after intervention). The exercise protocol consisted of 5 bouts of intensive 60-s (120% VO 2max ) cycling separated by 60 s of passive rest. Body composition, urinalysis and lactate concentration were evaluated - before (t0), immediately after (t1), 5' (t2), and 30' (t3) after exercise. Total body water and its active transport (TBW - total body water / ICW - intracellular water / ECW - extracellular water) showed no significant differences in all groups, at both occasions. In the post-hydration state we found a significant decrease of specific urine gravity in HM (1021±4.2 vs 1015±3.8 g/L) and LM (1022±3.1 vs 1008±4.2 g/L). We also found a significant increase of pH and lactate utilization rate in LM. In conclusion, the athletes hydrated with alkaline, low mineralized water demonstrated favourable changes in hydration status in response to high-intensity interval exercise with a significant decrease of specific urine gravity, increased urine pH and more efficient utilization of lactate after supramaximal exercise.

Plasma sprayed ceria-containing interlayer

DOEpatents

Schmidt, Douglas S.; Folser, George R.

2006-01-10

A plasma sprayed ceria-containing interlayer is provided. The interlayer has particular application in connection with a solid oxide fuel cell used within a power generation system. The fuel cell advantageously comprises an air electrode, a plasma sprayed interlayer disposed on at least a portion of the air electrode, a plasma sprayed electrolyte disposed on at least a portion of the interlayer, and a fuel electrode applied on at least a portion of the electrolyte.

Water binding in legume seeds

NASA Technical Reports Server (NTRS)

Vertucci, C. W.; Leopold, A. C.

1987-01-01

The physical status of water in seeds has a pivotal role in determining the physiological reactions that can take place in the dry state. Using water sorption isotherms from cotyledon and axis tissue of five leguminous seeds, the strength of water binding and the numbers of binding sites have been estimated using van't Hoff analyses and the D'Arcy/Watt equation. These parameters of water sorption are calculated for each of the three regions of water binding and for a range of temperatures. Water sorption characteristics are reflective of the chemical composition of the biological materials as well as the temperature at which hydration takes place. Changes in the sorption characteristics with temperature and hydration level may suggest hydration-induced structural changes in cellular components.

Mechanism of tyramine adsorption on Ca-montmorillonite.

PubMed

Chang, Po-Hsiang; Jiang, Wei-Teh; Li, Zhaohui

2018-06-10

Tyramine (TY) adsorption on a Ca-montmorillonite (SAz-2) was investigated with batch experiments and complementary analyses utilizing ultra-high performance liquid chromatography, ion chromatography, X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and thermogravimetry (TG). The adsorption reached equilibrium in 8 h, complying with the pseudo-second-order rate equation, and came to an adsorption capacity of 682 mmol kg -1 at pH 6-8.1, utilizing the Langmuir isotherm model. The adsorption of TY and desorption of exchangeable cations exhibited a linear relationship with a slope of 0.9, implying that the adsorption was largely influenced by a cation exchange mechanism. The effective adsorption was further verified by the characteristic TY bands in the FTIR spectra and the signals of mass loss due to TY decomposition in the TG measurements of the clay after adsorption experiments. Intercalation of hydrated TY into the clay interlayer was confirmed by XRD and TG analyses of the heated samples loaded with TY. The adsorption reached only 0.57 cation exchange capacity of the clay which was probably limited by the low charge density of TY as compared to the negative charge density of the clay surface and by the steric effects arising from the hydration of TY that increased its molecular size. Adsorption of TY on montmorillonite can make TY more resistant to thermal decomposition and possibly better preserved in aquatic and soil environments. Copyright © 2018 Elsevier B.V. All rights reserved.

Thermally stable diamond brazing

DOEpatents

Radtke, Robert P [Kingwood, TX

2009-02-10

A cutting element and a method for forming a cutting element is described and shown. The cutting element includes a substrate, a TSP diamond layer, a metal interlayer between the substrate and the diamond layer, and a braze joint securing the diamond layer to the substrate. The thickness of the metal interlayer is determined according to a formula. The formula takes into account the thickness and modulus of elasticity of the metal interlayer and the thickness of the TSP diamond. This prevents the use of a too thin or too thick metal interlayer. A metal interlayer that is too thin is not capable of absorbing enough energy to prevent the TSP diamond from fracturing. A metal interlayer that is too thick may allow the TSP diamond to fracture by reason of bending stress. A coating may be provided between the TSP diamond layer and the metal interlayer. This coating serves as a thermal barrier and to control residual thermal stress.

Tunneling Photocurrent Assisted by Interlayer Excitons in Staggered van der Waals Hetero-Bilayers.

PubMed

Luong, Dinh Hoa; Lee, Hyun Seok; Neupane, Guru Prakash; Roy, Shrawan; Ghimire, Ganesh; Lee, Jin Hee; Vu, Quoc An; Lee, Young Hee

2017-09-01

Vertically stacked van der Waals (vdW) heterostructures have been suggested as a robust platform for studying interfacial phenomena and related electric/optoelectronic devices. While the interlayer Coulomb interaction mediated by the vdW coupling has been extensively studied for carrier recombination processes in a diode transport, its correlation with the interlayer tunneling transport has not been elucidated. Here, a contrast is reported between tunneling and drift photocurrents tailored by the interlayer coupling strength in MoSe 2 /MoS 2 hetero-bilayers (HBs). The interfacial coupling modulated by thermal annealing is identified by the interlayer phonon coupling in Raman spectra and the emerging interlayer exciton peak in photoluminescence spectra. In strongly coupled HBs, positive photocurrents are observed owing to the inelastic band-to-band tunneling assisted by interlayer excitons that prevail over exciton recombinations. By contrast, weakly coupled HBs exhibit a negative photovoltaic diode behavior, manifested as a drift current without interlayer excitonic emissions. This study sheds light on tailoring the tunneling transport for numerous optoelectronic HB devices. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effects of a Ta interlayer on the phase transition of TiSi2 on Si(111)

NASA Astrophysics Data System (ADS)

Jeon, Hyeongtag; Jung, Bokhee; Kim, Young Do; Yang, Woochul; Nemanich, R. J.

2000-09-01

This study examines the effects of a thin Ta interlayer on the formation of TiSi2 on Si(111) substrate. The Ta interlayer was introduced by depositing Ta and Ti films sequentially on an atomically clean Si(111) substrate in an ultrahigh vacuum (UHV) system. Samples of 100 Å Ti with 5 and 10 Å Ta interlayers were compared to similar structures without an interlayer. After deposition, the substrates were annealed for 10 min, in situ, at temperatures between 500 and 750 °C in 50 °C increments. The TiSi2 formation with and without the Ta interlayer was analyzed with an X-ray diffractometer, Auger electron spectroscopy (AES), Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and a four-point probe. The AES analysis data showed a 1:2 ratio of Ti:Si in the Ti-silicide layer and indicated that the Ta layer remained at the interface between TiSi2 and the Si(111) substrate. The C 49-C 54 TiSi2 phase transition temperature was lowered by ˜200 °C. The C 49-C 54 TiSi2 phase transition temperature was 550 °C for the samples with a Ta interlayer and was 750 °C for the samples with no Ta interlayer. The sheet resistance of the Ta interlayered Ti silicide showed lower values of resistivity at low temperatures which indicated the change in phase transition temperature. The C 54 TiSi2 displayed different crystal orientation when the Ta interlayer was employed. The SEM and TEM micrographs showed that the TiSi2 with a Ta interlayer significantly suppressed the tendency to islanding and surface agglomeration.

Bioelectrical impedance vector analysis (BIVA) for measuring the hydration status in young elite synchronized swimmers

PubMed Central

Carrasco-Marginet, Marta; Castizo-Olier, Jorge; Rodríguez-Zamora, Lara; Iglesias, Xavier; Rodríguez, Ferran A.; Chaverri, Diego; Brotons, Daniel

2017-01-01

Purpose The assessment of body hydration is a complex process, and no measurement is valid for all situations. Bioelectrical impedance vector analysis (BIVA) has emerged as a relatively novel technique for assessing hydration status in sports. We applied BIVA a) to determine hydration changes evoked by an intense synchronized swimming (SS) training session; b) to characterize the sample of young elite swimmers in relation with a nonathletic reference population; and c) to generate its 50%, 75% and 95% percentiles of the bioelectrical variables. Methods Forty-nine elite SS female swimmers of two age categories, comen (Co: 13.9 ± 0.9 years, n = 34) and junior (Jr: 16.3 ± 0.6 years, n = 15), performed a long, high intensity training session. Body mass (BM) and bioelectrical variables (R, resistance; Xc, reactance; PA, phase angle; and Z, impedance module) were assessed pre- and post-training. BIVA was used to characterize 1) the distribution pattern of the bioelectrical vector (BIA vector) for both age groups, and 2) pre- to post-training BIA vector migration. Bioelectrical variables were also correlated with BM change values. Results Most swimmers were mostly located outside the 75% and some beyond the 95% percentile of the bioelectrical tolerance ellipses of the general population. The BIA vector showed statistically significant differences in both Co (T2 = 134.7, p = 0.0001) and Jr (T2 = 126.2, p < 0.001). Both groups were also bioelectrically different (T2 = 17.6, p < 0.001). After the training session, a decrease in BM (p = 0.0001) and an increase in BIA variables (p = 0.01) was observed. BIVA also showed a significant pre-post vector migration both in Co (T2 = 82.1; p < 0.001) and Jr (T2 = 41.8; p < 0.001). No correlations were observed between BM changes and bioelectrical variables. Conclusions BIVA showed specific bioelectrical characteristics in young elite SS athletes. Considering the decrease in BM and the migration of the BIA vector, we conclude that the homeostatic hydration status of these young elite female swimmers was affected by the execution of intense training sessions. From a methodological perspective, BIVA appears to be sensitive enough to detect subtle hydration changes, but further research is needed to ensure its validity and reliability. Moreover, these findings highlight the importance of ensuring adequate fluid intake during training in young SS athletes. PMID:28591135

Insight into hydrogen bonding of uranyl hydroxide layers and capsules by use of 1H magic-angle spinning NMR spectroscopy [Insight into the hydrogen bonding for uranyl hydroxides using 1H MAS NMR spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alam, Todd M.; Liao, Zuolei; Nyman, May

Solid-state 1H magic-angle spinning (MAS) NMR was used to investigate local proton environments in anhydrous [UO 2(OH) 2] (α-UOH) and hydrated uranyl hydroxide [(UO 2) 4O(OH) 6·5H 2O (metaschoepite). For the metaschoepite material, proton resonances of the μ 2-OH hydroxyl and interlayer waters were resolved, with two-dimensional (2D) double-quantum (DQ) 1H– 1H NMR correlation experiments revealing strong dipolar interactions between these different proton species. The experimental NMR results were combined with first-principles CASTEP GIPAW (gauge including projector-augmented wave) chemical shift calculations to develop correlations between hydrogen-bond strength and observed 1H NMR chemical shifts. Furthermore, these NMR correlations allowed characterization ofmore » local hydrogen-bond environments in uranyl U 24 capsules and of changes in hydrogen bonding that occurred during thermal dehydration of metaschoepite.« less

Crystal-chemical characteristics of nontronites from bottom sediments of Pacific ocean

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palchik, N. A., E-mail: nadezhda@igm.nsc.ru; Moroz, T. N.; Grigorieva, T. N.

A crystal-chemical analysis of the nontronite samples formed in deep-water sediments of the underwater Juan-de-Fuca ridge in the Pacific ocean has been performed using powder X-ray diffraction, IR spectroscopy, and Mössbauer spectroscopy. A comparison with the previously investigated nontronites from different regions of the Sea of Okhotsk showed that the structural features of these formations are due to the difference in the physicochemical parameters of their crystallization. The values of the basal interplanar spacing d{sub 001} (within 11–13 Å) in the samples analyzed are determined by the degree of hydration and cation filling of the interlayer space, while the differencesmore » in the IR spectra are due to isomorphic substitutions in the structure. The character of cation distribution and the nature and concentration of stacking faults in nontronite structures are determined. The differences in the composition, structure, and properties of nontronites of different origin are confirmed by theoretical calculations of their structural parameters.« less

Experimental and theoretical study of Co sorption in clay montmorillonites

NASA Astrophysics Data System (ADS)

Gil Rebaza, A. V.; Montes, M. L.; Taylor, M. A.; Errico, L. A.; Alonso, R. E.

2018-03-01

Montmorillonite (MMT) clays are 2:1 layered structures which in natural state may allocate different hydrated cations such as M-nH2O (M = Na, Ca, Fe, etc) in its interlayer space. Depending on the capability for ion sorption, these materials are interesting for environmental remediation. In this work we experimentally study the Co sorption in a natural Na-MMT using UV-visible spectrometry and XRD on semi-oriented samples, and then analyze the sorption ability of this clay by means of ab initio calculation performed on pristine MMT. The structural properties of Na-MMT and Co-adsorbed MMT, and the hyperfine parameters at different atomic sites were analyzed and compared with the experimental ones for the first, and for the case of the hyperfine parameters, presented for the first time for the last. The theoretical predictions based on total energy considerations confirm that Co incorporation replacing Na is energetically favorable. Also, the basal spacing d001 experimentally obtained is well reproduced.

Insight into hydrogen bonding of uranyl hydroxide layers and capsules by use of 1H magic-angle spinning NMR spectroscopy [Insight into the hydrogen bonding for uranyl hydroxides using 1H MAS NMR spectroscopy

DOE PAGES

Alam, Todd M.; Liao, Zuolei; Nyman, May; ...

2016-04-27

Solid-state 1H magic-angle spinning (MAS) NMR was used to investigate local proton environments in anhydrous [UO 2(OH) 2] (α-UOH) and hydrated uranyl hydroxide [(UO 2) 4O(OH) 6·5H 2O (metaschoepite). For the metaschoepite material, proton resonances of the μ 2-OH hydroxyl and interlayer waters were resolved, with two-dimensional (2D) double-quantum (DQ) 1H– 1H NMR correlation experiments revealing strong dipolar interactions between these different proton species. The experimental NMR results were combined with first-principles CASTEP GIPAW (gauge including projector-augmented wave) chemical shift calculations to develop correlations between hydrogen-bond strength and observed 1H NMR chemical shifts. Furthermore, these NMR correlations allowed characterization ofmore » local hydrogen-bond environments in uranyl U 24 capsules and of changes in hydrogen bonding that occurred during thermal dehydration of metaschoepite.« less

Role of low-temperature AlGaN interlayers in thick GaN on silicon by metalorganic vapor phase epitaxy

NASA Astrophysics Data System (ADS)

Fritze, S.; Drechsel, P.; Stauss, P.; Rode, P.; Markurt, T.; Schulz, T.; Albrecht, M.; Bläsing, J.; Dadgar, A.; Krost, A.

2012-06-01

Thin AlGaN interlayers have been grown into a thick GaN stack on Si substrates to compensate tensile thermal stress and significantly improve the structural perfection of the GaN. In particular, thicker interlayers reduce the density in a-type dislocations as concluded from x-ray diffraction (XRD) measurements. Beyond an interlayer thickness of 28 nm plastic substrate deformation occurs. For a thick GaN stack, the first two interlayers serve as strain engineering layers to obtain a crack-free GaN structure, while a third strongly reduces the XRD ω-(0002)-FWHM. The vertical strain and quality profile determined by several XRD methods demonstrates the individual impact of each interlayer.

Pregame Urine Specific Gravity and Fluid Intake by National Basketball Association Players During Competition

PubMed Central

Osterberg, Kristin L; Horswill, Craig A; Baker, Lindsay B

2009-01-01

Context: Urine specific gravity (USG) has been used to estimate hydration status in athletes on the field, with increasing levels of hypohydration indicated by higher USG measurements (eg, greater than 1.020). Whether initial hydration status based on a urine measure is related to subsequent drinking response during exercise or athletic competition is unclear. Objective: To determine the relationship between pregame USG and the volume of fluid consumed by players in a professional basketball game. Design: Cross-sectional study. Setting: Basketball players were monitored during Summer League competition. Patients or Other Participants: Players (n  =  29) from 5 teams of the National Basketball Association agreed to participate. Main Outcome Measure(s): Pregame USG was measured for each player on 2 occasions. Athletes were given ad libitum access to fluid during each game and were unaware of the purpose of the study. Volume of fluid intake was measured for each player. To assess sweat loss, athletes were weighed in shorts before and after each game. Results: Sweat loss ranged from 1.0 to 4.6 L, with a mean sweat loss of 2.2 ± 0.8 L. Fluid intake ranged from 0.1 to 2.9 L, with a mean fluid intake of 1.0 ± 0.6 L. Pregame USG was greater than 1.020 in 52% of the urine samples collected and was not correlated with fluid volume consumed during either of the games (r  =  0.15, P  =  .48, and r  =  0.15, P  =  .52, respectively). Conclusions: Approximately half of the players began the games in a hypohydrated state, as indicated by USG. Fluid intake during the game did not compensate for poor hydration status before competition. Furthermore, sweat losses in these players during games were substantial (greater than 2 L in approximately 20 minutes of playing time). Therefore, both pregame and during-game hydration strategies, such as beverage availability and player education, should be emphasized. PMID:19180219

Quantification of chromatographic effects of vitamin B supplementation in urine and implications for hydration assessment.

PubMed

Kenefick, Robert W; Heavens, K R; Dennis, W E; Caruso, E M; Guerriere, K I; Charkoudian, N; Cheuvront, S N

2015-07-15

Changes in body water elicit reflex adjustments at the kidney, thus maintaining fluid volume homeostasis. These renal adjustments change the concentration and color of urine, variables that can, in turn, be used as biomarkers of hydration status. It has been suggested that vitamin supplementation alters urine color; it is unclear whether any such alteration would confound hydration assessment via colorimetric evaluation. We tested the hypothesis that overnight vitamin B2 and/or B12 supplementation alters urine color as a marker of hydration status. Thirty healthy volunteers were monitored during a 3-day euhydrated baseline, confirmed via first morning nude body mass, urine specific gravity, and urine osmolality. Volunteers then randomly received B2 (n = 10), B12 (n = 10), or B2 + B12 (n = 10) at ∼200 × recommended dietary allowance. Euhydration was verified on trial days (two of the following: body mass ± 1.0% of the mean of visits 1-3, urine specific gravity < 1.02, urine osmolality < 700 mmol/kg). Vitamin purity and urinary B2 concentration ([B2]) and [B12] were quantified via ultraperformance liquid chromatography. Two independent observers assessed urine color using an eight-point standardized color chart. Following supplementation, urinary [B2] was elevated; however, urine color was not different between nonsupplemented and supplemented trials. For example, in the B2 trial, urinary [B2] increased from 8.6 × 10(4) ± 7.7 × 10(4) to 5.7 × 10(6) ± 5.3 × 10(6) nmol/l (P < 0.05), and urine color went from 4 ± 1 to 5 ± 1 (P > 0.05). Both conditions met the euhydrated color classification. We conclude that a large overnight dose of vitamins B2 and B12 does not confound assessment of euhydrated status via urine color. Copyright © 2015 the American Physiological Society.

Hydrate research activities that both support and derive from the monitoring station/sea-floor Observatory, Mississippi Canyon 118, northern Gulf of Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lutken, Carol

2013-07-31

A permanent observatory has been installed on the seafloor at Federal Lease Block, Mississippi Canyon 118 (MC118), northern Gulf of Mexico. Researched and designed by the Gulf of Mexico Hydrates Research Consortium (GOM-HRC) with the geological, geophysical, geochemical and biological characterization of in situ gas hydrates systems as the research goal, the site has been designated by the Bureau of Ocean Energy Management as a permanent Research Reserve where studies of hydrates and related ocean systems may take place continuously and cooperatively into the foreseeable future. The predominant seafloor feature at MC118 is a carbonate-hydrate complex, officially named Woolsey Moundmore » for the founder of both the GOM-HRC and the concept of the permanent seafloor hydrates research facility, the late James Robert “Bob” Woolsey. As primary investigator of the overall project until his death in mid-2008, Woolsey provided key scientific input and served as chief administrator for the Monitoring Station/ Seafloor Observatory (MS-SFO). This final technical report presents highlights of research and accomplishments to date. Although not all projects reached the status originally envisioned, they are all either complete or positioned for completion at the earliest opportunity. All Department of Energy funds have been exhausted in this effort but, in addition, leveraged to great advantage with additional federal input to the project and matched efforts and resources. This report contains final reports on all subcontracts issued by the University of Mississippi, Administrators of the project, Hydrate research activities that both support and derive from the monitoring station/sea-floor Observatory, Mississippi Canyon 118, northern Gulf of Mexico, as well as status reports on the major components of the project. All subcontractors have fulfilled their primary obligations. Without continued funds designated for further project development, the Monitoring Station/Seafloor Observatory is in danger of lapsing into disuse. However, for the present, interest in the site on the continental slope is healthy and The Center for Marine Resources and Environmental Technology continues to coordinate all activity at the MS/SFO as arranged through the BOEM in 2005. Field and laboratory research projects and findings are reviewed, new technologies and tests described. Many new sensors, systems and two custom ROVs have been developed specifically for this project. Characteristics of marine gas hydrates are dramatically more refined than when the project was initiated and include appear in sections entitled Accomplishments, Products and Publications.« less

Mechanisms for the adsorption of substituted nitrobenzenes by smectite clays.

PubMed

Boyd, S A; Sheng, G; Teppen, B J; Johnston, C T

2001-11-01

To more fully understand the potential for transport of nitroaromatic compounds in soils and subsoils,the adsorption of a series of para- and meta-substituted nitrobenzenes (SNBs) by K-smectite clay was measured. Adsorption isotherms were fit to the Freundlich equation, and the resultant Freundlich adsorption coefficients (log(Kf) were positively correlated with the Hammett substituent constant (r2 = 0.80). This relationship and a positive reaction constant (p = 1.15) indicate that the adsorption reaction is favored by electron-withdrawing substituents. These results are consistent with an electron donor (smectite)-acceptor (substituted nitrobenzene) mechanism offered previously. However, quantum calculations did not reveal any systematic relationship between the Hammett constant and the electron density on the aromatic ring, which would explain a donor-acceptor relationship. Rather, electron density donated by a second substituent on nitrobenzene appears to be appropriated by the nitro group leaving ring electron density unchanged. Fourier transform infrared spectroscopy revealed shifts in the -NO2 vibrational modes of 1,3,5-trinitrobenzene (TNB) upon adsorption to K+-smectite that were consistent with the complexation of K+ by -NO2 groups. Such TNB vibrational shifts were not observed for SWy-1 saturated with more strongly hydrated cations (i.e., Na+, Mg2+, Ca2+, and Ba2+). The simultaneous interaction of multiple -NO2 groups with exchangeable K+ was indicated by molecular dynamic simulations. Adsorption of SNBs by smectite clays appears to result from the additive interactions of -NO2 groups and secondary substituents with interlayer K+ ions. Adsorption occurs to a greater or lesser extent depending on the abilities of substituents to complex additional interlayer cations and the water solubilities of SNBs. We conclude that the adsorption trends of SNBs on K-SAz-1 can be explained without recourse to hypothetical electron donor-acceptor complexes.

Nanoencapsulation of Insulin into Zirconium Phosphate for Oral Delivery Applications

PubMed Central

Díaz, Agustín; David, Amanda; Pérez, Riviam; González, Millie L.; Báez, Adriana; Wark, Stacey E.; Zhang, Paul; Clearfield, Abraham; Colón, Jorge L.

2010-01-01

The encapsulation of insulin into different kinds of materials for non-invasive delivery is an important field of study because of the many drawbacks of painful needle and syringe delivery such as physiological stress, infection, and local hypertrophy, among others.1 A stable, robust, non-toxic, and viable non-invasive carrier for insulin delivery is needed. We present a new approach for protein nanoencapsulation using layered zirconium phosphate (ZrP) nanoparticles produced without any preintercalator present. The use of ZrP without preintercalators produces a highly pure material, without any kinds of contaminants, such as the preintercalator, which can be noxious. Cytotoxicity cell viability in vitro experiments for the ZrP nanoparticles show that ZrP is not toxic, or harmful, in a biological environment, as previously reported for rats.2 Contrary to previous preintercalator-based methods, we show that insulin can be nanoencapsulated in ZrP if a highly hydrate phase of ZrP with an interlayer distance of 10.3 Å (10.3 Å-ZrP or θ-ZrP) is used as precursor. The intercalation of insulin into ZrP produced a new insulin-intercalated ZrP phase with a ca. 27 Å interlayer distance, as determined by X-ray powder diffraction, demonstrating a successful nanoencapsulation of the hormone. The in vitro release profile of the hormone after the intercalation was determined and circular dichroism was used to study the hormone stability upon intercalation and release. The insulin remains stable in the layered material, at room temperature, for a considerable amount of time, improving the shell life of the peptidic hormone. This type of materials represents a strong candidate to develop a non-invasive insulin carrier for the treatment of diabetes mellitus. PMID:20707305

A 3D conductive carbon interlayer with ultrahigh adsorption capability for lithium-sulfur batteries

NASA Astrophysics Data System (ADS)

Zhao, Qian; Zhu, Qizhen; An, Yabin; Chen, Renjie; Sun, Ning; Wu, Feng; Xu, Bin

2018-05-01

To improve the cycling performance of the Li-S batteries, a 3D interwoven hollow interlayer with extremely high electrolyte adsorption capability up to 9.64 g g-1 was simply prepared by carbonization of cotton fabric (CCF). For comparison, an interlayer coated on separator was obtained by the slurry-coating method of powdery CCF. The key role of the adsorption capability is confirmed by comparing the electrochemical performance of Li-S batteries with these two interlayers. In the Li-S batteries with 3D CCF interlayer, massive dissolved polysulfides, together with the electrolyte, can be adsorbed and confined in the 3D CCF interlayer, providing substantial extra active sites and alleviating the shuttle effect effectively. As a result, the Li-S batteries with 3D CCF interlayer show much enhanced utilization of active materials (1346.9 mAh g-1 at 0.1C), prolonged cycle life (capacity retention of 80% after 100 cycles), and improved rate performance (553.2 mAh g-1 at 4C). Even for cathodes with high sulfur loading of 5 mg cm-2, the cells with 3D CCF interlayer perform a high capacity of 1085 mAh g-1 and retain 870.6 mAh g-1 after 75 cycles at 0.5 mA cm-2. These results not only provide a sustainable, low cost and easy-prepared 3D CCF interlayer, but also offer a promising strategy based on interlayer with high adsorption capability in designing high-performance Li-S batteries.

Large Frequency Change with Thickness in Interlayer Breathing Mode—Significant Interlayer Interactions in Few Layer Black Phosphorus

NASA Astrophysics Data System (ADS)

Luo, Xin; Lu, Xin; Koon, Gavin Kok Wai; Castro Neto, Antonio H.; Özyilmaz, Barbaros; Xiong, Qihua; Quek, Su Ying

2015-06-01

Bulk black phosphorus (BP) consists of puckered layers of phosphorus atoms. Few-layer BP, obtained from bulk BP by exfoliation, is an emerging candidate as a channel material in post-silicon electronics. A deep understanding of its physical properties and its full range of applications are still being uncovered. In this paper, we present a theoretical and experimental investigation of phonon properties in few-layer BP, focusing on the low-frequency regime corresponding to interlayer vibrational modes. We show that the interlayer breathing mode A3g shows a large redshift with increasing thickness; the experimental and theoretical results agreeing well. This thickness dependence is two times larger than that in the chalcogenide materials such as few-layer MoS2 and WSe2, because of the significantly larger interlayer force constant and smaller atomic mass in BP. The derived interlayer out-of-plane force constant is about 50% larger than that in graphene and MoS2. We show that this large interlayer force constant arises from the sizable covalent interaction between phosphorus atoms in adjacent layers, and that interlayer interactions are not merely of the weak van der Waals type. These significant interlayer interactions are consistent with the known surface reactivity of BP, and have been shown to be important for electric-field induced formation of Dirac cones in thin film BP.

Large Frequency Change with Thickness in Interlayer Breathing Mode--Significant Interlayer Interactions in Few Layer Black Phosphorus.

PubMed

Luo, Xin; Lu, Xin; Koon, Gavin Kok Wai; Castro Neto, Antonio H; Özyilmaz, Barbaros; Xiong, Qihua; Quek, Su Ying

2015-06-10

Bulk black phosphorus (BP) consists of puckered layers of phosphorus atoms. Few-layer BP, obtained from bulk BP by exfoliation, is an emerging candidate as a channel material in post-silicon electronics. A deep understanding of its physical properties and its full range of applications are still being uncovered. In this paper, we present a theoretical and experimental investigation of phonon properties in few-layer BP, focusing on the low-frequency regime corresponding to interlayer vibrational modes. We show that the interlayer breathing mode A(3)g shows a large redshift with increasing thickness; the experimental and theoretical results agree well. This thickness dependence is two times larger than that in the chalcogenide materials, such as few-layer MoS2 and WSe2, because of the significantly larger interlayer force constant and smaller atomic mass in BP. The derived interlayer out-of-plane force constant is about 50% larger than that of graphene and MoS2. We show that this large interlayer force constant arises from the sizable covalent interaction between phosphorus atoms in adjacent layers and that interlayer interactions are not merely of the weak van der Waals type. These significant interlayer interactions are consistent with the known surface reactivity of BP and have been shown to be important for electric-field induced formation of Dirac cones in thin film BP.

Probing the Interlayer Exciton Physics in a MoS2/MoSe2/MoS2 van der Waals Heterostructure.

PubMed

Baranowski, M; Surrente, A; Klopotowski, L; Urban, J M; Zhang, N; Maude, D K; Wiwatowski, K; Mackowski, S; Kung, Y C; Dumcenco, D; Kis, A; Plochocka, P

2017-10-11

Stacking atomic monolayers of semiconducting transition metal dichalcogenides (TMDs) has emerged as an effective way to engineer their properties. In principle, the staggered band alignment of TMD heterostructures should result in the formation of interlayer excitons with long lifetimes and robust valley polarization. However, these features have been observed simultaneously only in MoSe 2 /WSe 2 heterostructures. Here we report on the observation of long-lived interlayer exciton emission in a MoS 2 /MoSe 2 /MoS 2 trilayer van der Waals heterostructure. The interlayer nature of the observed transition is confirmed by photoluminescence spectroscopy, as well as by analyzing the temporal, excitation power, and temperature dependence of the interlayer emission peak. The observed complex photoluminescence dynamics suggests the presence of quasi-degenerate momentum-direct and momentum-indirect bandgaps. We show that circularly polarized optical pumping results in long-lived valley polarization of interlayer exciton. Intriguingly, the interlayer exciton photoluminescence has helicity opposite to the excitation. Our results show that through a careful choice of the TMDs forming the van der Waals heterostructure it is possible to control the circular polarization of the interlayer exciton emission.

First-principles study on interlayer state in alkali and alkaline earth metal atoms intercalated bilayer graphene

NASA Astrophysics Data System (ADS)

Kaneko, Tomoaki; Saito, Riichiro

2017-11-01

Energetics and electronic structures of alkali metal (Li, Na, K, Rb, and Cs) and alkaline earth metal (Be, Mg, Ca, Sr, and Ba) atoms intercalated bilayer graphene are systematically investigated using first-principles calculations based on density functional theory. Formation of alkali and alkaline earth metal atoms intercalated bilayer graphene is exothermic except for Be and Mg. The interlayer state between two graphene layers is occupied for K, Rb, Cs, Ca, Sr, and Ba. We find that the energetic position of the interlayer states between bilayer graphene monotonically shifts downward with increasing of interlayer distance. The interlayer distances of more than 4.5 Å and 4.0 Å, respectively, are necessary for the occupation of the interlayer state in bilayer graphene for alkali and alkaline earth metal atoms, which is almost independent of the intercalant metal species. We discuss the relevance to occurrence of superconductivity for the metal intercalated bilayer graphene in terms of the occupation of the interlayer state and the phonon frequency of metal ions.

The graphene oxide membrane immersing in the aqueous solution studied by electrochemical impedance spectroscopy

NASA Astrophysics Data System (ADS)

Zhang, Yongjing; Chen, Zhe; Yao, Lei; Wang, Xiao; Fu, Ping; Lin, Zhidong

2018-04-01

The interlayer spacing of graphene oxide (GO) is a key property for GO membrane. To probe the variation of interlayer spacing of the GO membrane immersing in KCl aqueous solution, electrochemical impedance spectroscopy (EIS), x-ray diffraction (XRD) and computational calculation was utilized in this study. The XRD patterns show that soaking in KCl aqueous solution leads to an increase of interlayer spacing of GO membrane. And the EIS results indicate that during the immersing process, the charge transfer resistance of GO membrane decreases first and then increases. Computational calculation confirms that intercalated water molecules can result in an increase of interlayer spacing of GO membrane, while the permeation of K+ ions would lead to a decrease of interlayer spacing. All the results are in agreement with each other. It suggests that during the immersing process, the interlayer spacing of GO enlarges first and then decreases. EIS can be a promisingly online method for examining the interlayer spacing of GO in the aqueous solution.

Electron microscopy investigations of purity of AlN interlayer in Al{sub x}Ga{sub 1-x}N/GaN heterostructures grown by plasma assisted molecular beam epitaxy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sridhara Rao, D. V.; Jain, Anubha; Lamba, Sushil

2013-05-13

The electron microscopy was used to characterize the AlN interlayer in Al{sub x}Ga{sub 1-x}N/AlN/GaN heterostructures grown by plasma assisted molecular beam epitaxy (PAMBE). We show that the AlN interlayer grown by PAMBE is without gallium and oxygen incorporation and the interfaces are coherent. The AlN interlayer has the ABAB stacking of lattice planes as expected for the wurtzite phase. High purity of AlN interlayer with the ABAB stacking leads to larger conduction band offset along with stronger polarization effects. Our studies show that the origin of lower sheet resistance obtained by PAMBE is the purity of AlN interlayer.

Effects of the F₄TCNQ-Doped Pentacene Interlayers on Performance Improvement of Top-Contact Pentacene-Based Organic Thin-Film Transistors.

PubMed

Fan, Ching-Lin; Lin, Wei-Chun; Chang, Hsiang-Sheng; Lin, Yu-Zuo; Huang, Bohr-Ran

2016-01-13

In this paper, the top-contact (TC) pentacene-based organic thin-film transistor (OTFT) with a tetrafluorotetracyanoquinodimethane (F₄TCNQ)-doped pentacene interlayer between the source/drain electrodes and the pentacene channel layer were fabricated using the co-evaporation method. Compared with a pentacene-based OTFT without an interlayer, OTFTs with an F₄TCNQ:pentacene ratio of 1:1 showed considerably improved electrical characteristics. In addition, the dependence of the OTFT performance on the thickness of the F₄TCNQ-doped pentacene interlayer is weaker than that on a Teflon interlayer. Therefore, a molecular doping-type F₄TCNQ-doped pentacene interlayer is a suitable carrier injection layer that can improve the TC-OTFT performance and facilitate obtaining a stable process window.

Influence of the Organic Species and Oxoanion in the Synthesis of two Uranyl Sulfate Hydrates, (H 3 O) 2 [(UO 2 ) 2 (SO 4 ) 3 ­(H 2 O)]·7H 2 O and (H 3 O) 2 [(UO 2 ) 2 (SO 4 ) 3 (H 2 O)]·4H 2 O, and a Uranyl Selenate-Selenite [C 5 H 6 N][(UO 2 )(SeO 4 )(HSeO 3 )

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jouffret, Laurent J.; Wylie, Ernest M.; Burns, Peter C.

2012-08-08

Two uranyl sulfate hydrates, (H3O)2[(UO2)2(SO4)3(H2O)]·7H2O (NDUS) and (H3O)2[(UO2)2(SO4)3(H2O)]·4H2O (NDUS1), and one uranyl selenate-selenite [C5H6N][(UO2)(SeO4)(HSeO3)] (NDUSe), were obtained and their crystal structures solved. NDUS and NDUSe result from reactions in highly acidic media in the presence of L-cystine at 373 K. NDUS crystallized in a closed vial at 278 K after 5 days and NDUSe in an open beaker at 278 K after 2 weeks. NDUS1 was synthesized from aqueous solution at room temperature over the course of a month. NDUS, NDUS1, and NDUSe crystallize in the monoclinic space group P21/n, a = 15.0249(4) Å,b = 9.9320(2) Å, c = 15.6518(4)more » Å, β = 112.778(1)°, V = 2153.52(9) Å3,Z = 4, the tetragonal space group P43212, a = 10.6111(2) Å,c = 31.644(1) Å, V = 3563.0(2) Å3, Z = 8, and in the monoclinic space group P21/n, a = 8.993(3) Å, b = 13.399(5) Å, c = 10.640(4) Å,β = 108.230(4)°, V = 1217.7(8) Å3, Z = 4, respectively.The structural units of NDUS and NDUS1 are two-dimensional uranyl sulfate sheets with a U/S ratio of 2/3. The structural unit of NDUSe is a two-dimensional uranyl selenate-selenite sheets with a U/Se ratio of 1/2. In-situ reaction of the L-cystine ligands gives two distinct products for the different acids used here. Where sulfuric acid is used, only H3O+ cations are located in the interlayer space, where they balance the charge of the sheets, whereas where selenic acid is used, interlayer C5H6N+ cations result from the cyclization of the carboxyl groups of L-cystine, balancing the charge of the sheets.« less

Effect of particle size on the experimental dissolution and auto-aluminization processes of K-vermiculite

NASA Astrophysics Data System (ADS)

Viennet, Jean-Christophe; Hubert, Fabien; Tertre, Emmanuel; Ferrage, Eric; Robin, Valentin; Dzene, Liva; Cochet, Carine; Turpault, Marie-Pierre

2016-05-01

In acidic soils, the fixation of Al in the interlayer spaces of 2:1 clay minerals and the subsequent formation of hydroxyl interlayer minerals (HIMs) are known to reduce soil fertility. The resulting crystal structure of HIMs consist of complex mixed-layer minerals (MLMs) with contrasting relative proportions of expandable, hydroxy-interlayers (HI) and illite layers. The present study aims to experimentally assess the influence of particle size on the formation of such complex HIMs for vermiculite saturated with potassium (K). Based on chemical and structural data, this study reports the dissolution and Al-interlayer occupancy of three size fractions (0.1-0.2, 1-2 and 10-20 μm) of K-vermiculite, which were obtained at pH = 3 by using stirred flow-through reactors. The Al-interlayer occupancies were ordered 0.1-0.2 μm < 10-20 μm < 1-2 μm even though the dissolution rate (in molvermiculite g-1 s-1) increases with decreasing particle size. For fine particles (0.1-0.2 μm), a rapid but low Al-interlayer occupancy during the transitory state and a null rate in the steady-state were evidenced and interpreted as indicating (i) a rapid but limited K+ interlayer exchange during the first step of the overall reactions and (ii) a stoichiometric dissolution of the crystal (TOT layer + interlayer) in the steady-state. By contrast, although the stoichiometric dissolution of the TOT layer is reached in the steady-state for the coarsest fractions (10-20 and 1-2 μm), the Al-interlayer occupancies continue to evolve due to the exchange of interlayer K+, which continues to progress for a longer duration. The mechanism of auto-aluminization is interpreted in the present study as multiple processes that involve (i) the dissolution of the mineral under acidic conditions, (ii) the interlayer diffusion of initial interlayer cations and their exchange with those from the aqueous phase and (iii) the fixation of interlayer aluminum. Competition between the kinetics of ion-exchange reactions and that of mineral dissolution is responsible for the above Al-interlayer occupancy order among the particle sizes (i.e., 0.1-0.2 μm < 10-20 μm < 1-2 μm). Moreover, this mechanism may be the cause of complex mineralogical structures such as mixed-layer minerals, which are commonly found in the clay-size fraction of acidic soils.

Low-Frequency Shear and Layer-Breathing Modes in Raman Scattering of Two-Dimensional Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang, Liangbo; Zhang, Jun; Sumpter, Bobby G.

Ever since the isolation of single-layer graphene in 2004, two-dimensional layered structures have been among the most extensively studied classes of materials. To date, the pool of two-dimensional materials (2DMs) continues to grow at an accelerated pace and already covers an extensive range of fascinating and technologically relevant properties. An array of experimental techniques have been developed and used to fully characterize and understand these properties. In particular, Raman spectroscopy has proven to be a key experimental technique, thanks to its capability to identify minute structural and electronic effects in nondestructive measurements. While high-frequency (HF) intralayer Raman modes have beenmore » extensively employed for 2DMs, recent experimental and theoretical progress has demonstrated that low-frequency (LF) interlayer Raman modes are more effective at determining layer numbers and stacking configurations, and provide a unique opportunity to study interlayer coupling. These advantages are due to 2DMs’ unique interlayer vibration patterns where each layer behaves as an almost rigidly moving object with restoring forces corresponding to weak interlayer interactions. Compared to HF Raman modes, the relatively small attention originally devoted to LF Raman modes is largely due to their weaker signal and their proximity to the strong Rayleigh line background, which previously made their detection challenging. Recent progress in Raman spectroscopy with technical and hardware upgrades now makes it possible to probe LF modes with a standard single-stage Raman system and has proven crucial to characterize and understand properties of 2DMs. Here, we present a comprehensive and forward-looking review on the current status of exploiting LF Raman modes of 2DMs from both experimental and theoretical perspectives, revealing the fundamental physics and technological significance of LF Raman modes in advancing the field of 2DMs. We review a broad array of materials, with varying thickness and stacking configurations, discuss the effect of in-plane anisotropy, and present a generalized linear chain model and interlayer bond polarizability model to rationalize the experimental findings. We also discuss the instrumental improvements of Raman spectroscopy to enhance and separate LF Raman signals from the Rayleigh line. Lastly, we highlight the opportunities and challenges ahead in this fast-developing field.« less

Low-Frequency Shear and Layer-Breathing Modes in Raman Scattering of Two-Dimensional Materials

DOE PAGES

Liang, Liangbo; Zhang, Jun; Sumpter, Bobby G.; ...

2017-11-03

Ever since the isolation of single-layer graphene in 2004, two-dimensional layered structures have been among the most extensively studied classes of materials. To date, the pool of two-dimensional materials (2DMs) continues to grow at an accelerated pace and already covers an extensive range of fascinating and technologically relevant properties. An array of experimental techniques have been developed and used to fully characterize and understand these properties. In particular, Raman spectroscopy has proven to be a key experimental technique, thanks to its capability to identify minute structural and electronic effects in nondestructive measurements. While high-frequency (HF) intralayer Raman modes have beenmore » extensively employed for 2DMs, recent experimental and theoretical progress has demonstrated that low-frequency (LF) interlayer Raman modes are more effective at determining layer numbers and stacking configurations, and provide a unique opportunity to study interlayer coupling. These advantages are due to 2DMs’ unique interlayer vibration patterns where each layer behaves as an almost rigidly moving object with restoring forces corresponding to weak interlayer interactions. Compared to HF Raman modes, the relatively small attention originally devoted to LF Raman modes is largely due to their weaker signal and their proximity to the strong Rayleigh line background, which previously made their detection challenging. Recent progress in Raman spectroscopy with technical and hardware upgrades now makes it possible to probe LF modes with a standard single-stage Raman system and has proven crucial to characterize and understand properties of 2DMs. Here, we present a comprehensive and forward-looking review on the current status of exploiting LF Raman modes of 2DMs from both experimental and theoretical perspectives, revealing the fundamental physics and technological significance of LF Raman modes in advancing the field of 2DMs. We review a broad array of materials, with varying thickness and stacking configurations, discuss the effect of in-plane anisotropy, and present a generalized linear chain model and interlayer bond polarizability model to rationalize the experimental findings. We also discuss the instrumental improvements of Raman spectroscopy to enhance and separate LF Raman signals from the Rayleigh line. Lastly, we highlight the opportunities and challenges ahead in this fast-developing field.« less

Factors Associated with Pre-Event Hydration Status and Drinking Behavior of Middle-Aged Cyclists.

PubMed

Yates, B A; Ellis, L A; Butts, C L; McDermott, B P; Williamson, K H; Armstrong, L E

2018-01-01

Water is an essential nutrient for thermoregulation, metabolism, cognition, and overall physiological homeostatic function. However, aging adults display a blunted thirst mechanism and subsequently have an increased risk for dehydration or hyponatremia. Fluid consumption behaviors are modifiable and the importance of practicing adequate drinking behaviors for aging adults is amplified during exercise. Identification of aging adult's hydration beliefs and how they attain hydration advice could provide valuable information into ways to promote better drinking habits to reduce fluid imbalances. Thus, this investigation evaluated the knowledge, beliefs and behaviors of middle-aged cyclists (MA) that were associated with hydration status and drinking behavior, before and during a 164-km mass-participation event (ambient temperature, 33.3±2.8ºC(mean±SD)). This cross-sectional field study retrospectively grouped participants by their second urine specific gravity (Usg) measurement of the event morning prior to a mass participation cycling event. Usg was assessed via handheld refractometer. The Hotter N' Hell Hundred 164-km cycling event in Wichita Falls, Texas during the month of August. 36 male recreational cyclists (age, 53±9 y(mean±SD)). Participants were grouped according their urine specific gravity as either slightly hyperhydrated (SH; n=12, Usg≤1.014), euhydrated (EUH; n=12, Usg, 1.015-1.020), or slightly dehydrated (SD; n=12, Usg≥1.021). Exercise histories and questionnaires were recorded 24-48 h prior to the cycling event. Regardless of pre-event hydration status, all groups experienced a similar body mass loss during the 164-km event and finished with statistically similar exercise times; also, drinking behavior within all groups was influenced by multiple factors. The primary factors associated with MA cyclist drinking behavior were trial and error/personal history and thirst; further, the majority of cyclists (≥65%) in SH, EUH, and SD believed that dehydration affects performance negatively. The least important factors included rehydration recommendations from scientific and sports medicine organizations, plus information from sports drink manufacturers. Considering the complexity of the present findings and the physiological changes that accompany aging such as delayed thirst perception, we recommend that MA cyclists formulate an individualized drinking plan that is based on observations during exercise.

Effects of the F4TCNQ-Doped Pentacene Interlayers on Performance Improvement of Top-Contact Pentacene-Based Organic Thin-Film Transistors

PubMed Central

Fan, Ching-Lin; Lin, Wei-Chun; Chang, Hsiang-Sheng; Lin, Yu-Zuo; Huang, Bohr-Ran

2016-01-01

In this paper, the top-contact (TC) pentacene-based organic thin-film transistor (OTFT) with a tetrafluorotetracyanoquinodimethane (F4TCNQ)-doped pentacene interlayer between the source/drain electrodes and the pentacene channel layer were fabricated using the co-evaporation method. Compared with a pentacene-based OTFT without an interlayer, OTFTs with an F4TCNQ:pentacene ratio of 1:1 showed considerably improved electrical characteristics. In addition, the dependence of the OTFT performance on the thickness of the F4TCNQ-doped pentacene interlayer is weaker than that on a Teflon interlayer. Therefore, a molecular doping-type F4TCNQ-doped pentacene interlayer is a suitable carrier injection layer that can improve the TC-OTFT performance and facilitate obtaining a stable process window. PMID:28787845

Band engineering in twisted molybdenum disulfide bilayers

NASA Astrophysics Data System (ADS)

Zhao, Yipeng; Liao, Chengwei; Ouyang, Gang

2018-05-01

In order to explore the theoretical relationship between interlayer spacing, interaction and band offset at the atomic level in vertically stacked two-dimensional (2D) van der Waals (vdW) structures, we propose an analytical model to address the evolution of interlayer vdW coupling with random stacking configurations in MoS2 bilayers based on the atomic-bond-relaxation correlation mechanism. We found that interlayer spacing changes substantially with respect to the orientations, and the bandgap increases from 1.53 eV (AB stacking) to 1.68 eV (AA stacking). Our results reveal that the evolution of interlayer vdW coupling originates from the interlayer interaction, leading to interlayer separations and electronic properties changing with stacking configurations. Our predictions constitute a demonstration of twist engineering the band shift in the emergent class of 2D crystals, transition-metal dichalcogenides.

Effect of sputtered titanium interlayers on the properties of nanocrystalline diamond films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Cuiping, E-mail: licp226@126.com, E-mail: limingji@163.com; Li, Mingji, E-mail: licp226@126.com, E-mail: limingji@163.com; Wu, Xiaoguo

2016-04-07

Ti interlayers with different thicknesses were sputtered on Si substrates and then ultrasonically seeded in a diamond powder suspension. Nanocrystalline diamond (NCD) films were deposited using a dc arc plasma jet chemical vapor deposition system on the seeded Ti/Si substrates. Atomic force microscopy and scanning electron microscopy tests showed that the roughness of the prepared Ti interlayer increased with increasing thickness. The effects of Ti interlayers with various thicknesses on the properties of NCD films were investigated. The results show nucleation, growth, and microstructure of the NCD films are strongly influenced by the Ti interlayers. The addition of a Timore » interlayer between the Si substrate and the NCD films can significantly enhance the nucleation rate and reduce the surface roughness of the NCD. The NCD film on a 120 nm Ti interlayer possesses the fastest nucleation rate and the smoothest surface. Raman spectra of the NCD films show trans-polyacetylene relevant peaks reduce with increasing Ti interlayer thickness, which can owe to the improvement of crystalline at grain boundaries. Furthermore, nanoindentation measurement results show that the NCD film on a 120 nm Ti interlayer displays a higher hardness and elastic modulus. High resolution transmission electron microscopy images of a cross-section show that C atoms diffuse into the Ti layer and Si substrate and form TiC and SiC hard phases, which can explain the enhancement of mechanical properties of NCD.« less

The use of moderated mediated analysis to study the influence of hypo-hydration on working memory.

PubMed

Young, Hayley A; Benton, David

2016-07-13

To date, dehydration has been typically reported to infl uence psychological parameters when there has been at least a 2% loss of body mass, although there has been little examination of those going about their everyday lives, those who have lost less than 1% of body mass. In such situations factors such as the initial hydration status and individual differences in the response to a reduced fl uid intake are likely to be infl uential. Yet to study the complexity added by such additional variables novel methods of statistical analysis are required. The present study describes the use of moderated mediation, an approach that asks various questions: fi rstly, is drinking infl uential?; secondly, does a mediator (e.g.,thirst) sit between an independent and dependent variable?; and thirdly, does an effect only occur under certain conditions such as initial osmolality? In the study, 118 subjects were exposed to 30 °C for four hours during which they half drank 300 ml water. The serial sevens test of working memory was performed before and at the end of the procedure. A 0.6% loss of body mass reduced the effi ciency of working memory. Those who consumed water had better working memory; working memory was worse in participants who lost more body mass or became thirstier, but only in those with higher levels of baseline osmolality. Small variations in hydration status infl uenced cognitive functioning although there were individual differences in the response. The parameters that influence an adverse response to hypo-hydration need to be established to allow giving appropriate advice.

Time-varying multiplex network: Intralayer and interlayer synchronization

NASA Astrophysics Data System (ADS)

Rakshit, Sarbendu; Majhi, Soumen; Bera, Bidesh K.; Sinha, Sudeshna; Ghosh, Dibakar

2017-12-01

A large class of engineered and natural systems, ranging from transportation networks to neuronal networks, are best represented by multiplex network architectures, namely a network composed of two or more different layers where the mutual interaction in each layer may differ from other layers. Here we consider a multiplex network where the intralayer coupling interactions are switched stochastically with a characteristic frequency. We explore the intralayer and interlayer synchronization of such a time-varying multiplex network. We find that the analytically derived necessary condition for intralayer and interlayer synchronization, obtained by the master stability function approach, is in excellent agreement with our numerical results. Interestingly, we clearly find that the higher frequency of switching links in the layers enhances both intralayer and interlayer synchrony, yielding larger windows of synchronization. Further, we quantify the resilience of synchronous states against random perturbations, using a global stability measure based on the concept of basin stability, and this reveals that intralayer coupling strength is most crucial for determining both intralayer and interlayer synchrony. Lastly, we investigate the robustness of interlayer synchronization against a progressive demultiplexing of the multiplex structure, and we find that for rapid switching of intralayer links, the interlayer synchronization persists even when a large number of interlayer nodes are disconnected.

The thickness design of unintentionally doped GaN interlayer matched with background doping level for InGaN-based laser diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, P.; Zhao, D. G., E-mail: dgzhao@red.semi.ac.cn; Jiang, D. S.

2016-03-15

In order to reduce the internal optical loss of InGaN laser diodes, an unintentionally doped GaN (u-GaN) interlayer is inserted between InGaN/GaN multiple quantum well active region and Al{sub 0.2}Ga{sub 0.8}N electron blocking layer. The thickness design of u-GaN interlayer matching up with background doping level for improving laser performance is studied. It is found that a suitably chosen u-GaN interlayer can well modulate the optical absorption loss and optical confinement factor. However, if the value of background doping concentration of u-GaN interlayer is too large, the output light power may decrease. The analysis of energy band diagram of amore » LD structure with 100 nm u-GaN interlayer shows that the width of n-side depletion region decreases when the background concentration increases, and may become even too small to cover whole MQW, resulting in a serious decrease of the output light power. It means that a suitable interlayer thickness design matching with the background doping level of u-GaN interlayer is significant for InGaN-based laser diodes.« less

Time-varying multiplex network: Intralayer and interlayer synchronization.

PubMed

Rakshit, Sarbendu; Majhi, Soumen; Bera, Bidesh K; Sinha, Sudeshna; Ghosh, Dibakar

2017-12-01

A large class of engineered and natural systems, ranging from transportation networks to neuronal networks, are best represented by multiplex network architectures, namely a network composed of two or more different layers where the mutual interaction in each layer may differ from other layers. Here we consider a multiplex network where the intralayer coupling interactions are switched stochastically with a characteristic frequency. We explore the intralayer and interlayer synchronization of such a time-varying multiplex network. We find that the analytically derived necessary condition for intralayer and interlayer synchronization, obtained by the master stability function approach, is in excellent agreement with our numerical results. Interestingly, we clearly find that the higher frequency of switching links in the layers enhances both intralayer and interlayer synchrony, yielding larger windows of synchronization. Further, we quantify the resilience of synchronous states against random perturbations, using a global stability measure based on the concept of basin stability, and this reveals that intralayer coupling strength is most crucial for determining both intralayer and interlayer synchrony. Lastly, we investigate the robustness of interlayer synchronization against a progressive demultiplexing of the multiplex structure, and we find that for rapid switching of intralayer links, the interlayer synchronization persists even when a large number of interlayer nodes are disconnected.

Interlayer Exciton Optoelectronics in a 2D Heterostructure p-n Junction.

PubMed

Ross, Jason S; Rivera, Pasqual; Schaibley, John; Lee-Wong, Eric; Yu, Hongyi; Taniguchi, Takashi; Watanabe, Kenji; Yan, Jiaqiang; Mandrus, David; Cobden, David; Yao, Wang; Xu, Xiaodong

2017-02-08

Semiconductor heterostructures are backbones for solid-state-based optoelectronic devices. Recent advances in assembly techniques for van der Waals heterostructures have enabled the band engineering of semiconductor heterojunctions for atomically thin optoelectronic devices. In two-dimensional heterostructures with type II band alignment, interlayer excitons, where Coulomb bound electrons and holes are confined to opposite layers, have shown promising properties for novel excitonic devices, including a large binding energy, micron-scale in-plane drift-diffusion, and a long population and valley polarization lifetime. Here, we demonstrate interlayer exciton optoelectronics based on electrostatically defined lateral p-n junctions in a MoSe 2 -WSe 2 heterobilayer. Applying a forward bias enables the first observation of electroluminescence from interlayer excitons. At zero bias, the p-n junction functions as a highly sensitive photodetector, where the wavelength-dependent photocurrent measurement allows the direct observation of resonant optical excitation of the interlayer exciton. The resulting photocurrent amplitude from the interlayer exciton is about 200 times smaller than the resonant excitation of intralayer exciton. This implies that the interlayer exciton oscillator strength is 2 orders of magnitude smaller than that of the intralayer exciton due to the spatial separation of electron and hole to the opposite layers. These results lay the foundation for exploiting the interlayer exciton in future 2D heterostructure optoelectronic devices.

Safety Profile of Stromal Hydration of Clear Corneal Incisions with Cefuroxime in the Mouse Model.

PubMed

Moosajee, Mariya; Tracey-White, Dhani; Harbottle, Richard P; Ferguson, Veronica

2016-09-01

The use of sutureless clear corneal incisions (CCIs) for phacoemulsification is an established surgical technique, but the dynamic morphology of the wound and poor construction can lead to an increased risk of postoperative endophthalmitis. Stromal hydration with balanced salt solution (BSS) can improve the self-sealing status. Intracameral cefuroxime has reduced endophthalmitis rates. This study investigates the safety profile of stromal hydration with cefuroxime, as sequestering antibiotic at the wound may potentially provide added protection against infection. MF-1 mice underwent bilateral CCI, followed by stromal hydration with 5 μL of 10 mg/mL cefuroxime, cefuroxime-texas red conjugate (for detection using confocal microscopy), or BSS. Corneas were harvested from 1 h to 12 weeks postoperatively; gross morphology, histology, and apoptotic cell death levels were investigated to determine the safety profile. Bactericidal activity of cefuroxime was assayed using homogenized whole cornea following stromal hydration at 1 h, 24 h, and day 7 against gram-negative Escherichia coli. Cefuroxime stromal hydration did not alter corneal morphology, with no evidence of corneal scarring or vascularization. Corneal histology and levels of apoptosis were minimal and comparable to the BSS groups up to 12 weeks. Confocal microscopy detected cefuroxime-texas red up to 1 week surrounding the corneal wound. Whole corneal tissue homogenates displayed bactericidal activity up to 24 h postoperatively. Stromal hydration of CCI with cefuroxime is safe in mouse corneas. A reservoir of antibiotic at the wound can potentially act as a barrier of defense against infection following cataract and associated ocular surgery.

Does hydration status affect MRI measures of brain volume or water content?

PubMed

Meyers, Sandra M; Tam, Roger; Lee, Jimmy S; Kolind, Shannon H; Vavasour, Irene M; Mackie, Emilie; Zhao, Yinshan; Laule, Cornelia; Mädler, Burkhard; Li, David K B; MacKay, Alex L; Traboulsee, Anthony L

2016-08-01

To determine whether differences in hydration state, which could arise from routine clinical procedures such as overnight fasting, affect brain total water content (TWC) and brain volume measured with magnetic resonance imaging (MRI). Twenty healthy volunteers were scanned with a 3T MR scanner four times: day 1, baseline scan; day 2, hydrated scan after consuming 3L of water over 12 hours; day 3, dehydrated scan after overnight fasting of 9 hours, followed by another scan 1 hour later for reproducibility. The following MRI data were collected: T2 relaxation (for TWC measurement), inversion recovery (for T1 measurement), and 3D T1 -weighted (for brain volumes). Body weight and urine specific gravity were also measured. TWC was calculated by fitting the T2 relaxation data with a nonnegative least-squares algorithm, with corrections for T1 relaxation and image signal inhomogeneity and normalization to ventricular cerebrospinal fluid. Brain volume changes were measured using SIENA. TWC means were calculated within 14 tissue regions. Despite indications of dehydration as demonstrated by increases in urine specific gravity (P = 0.03) and decreases in body weight (P = 0.001) between hydrated and dehydrated scans, there was no measurable change in TWC (within any brain region) or brain volume between hydration states. We demonstrate that within a range of physiologic conditions commonly encountered in routine clinical scans (no pretreatment with hydration, well hydrated before MRI, and overnight fasting), brain TWC and brain volumes are not substantially affected in a healthy control cohort. J. Magn. Reson. Imaging 2016;44:296-304. © 2016 Wiley Periodicals, Inc.

Interlayer interactions in graphites.

PubMed

Chen, Xiaobin; Tian, Fuyang; Persson, Clas; Duan, Wenhui; Chen, Nan-xian

2013-11-06

Based on ab initio calculations of both the ABC- and AB-stacked graphites, interlayer potentials (i.e., graphene-graphene interaction) are obtained as a function of the interlayer spacing using a modified Möbius inversion method, and are used to calculate basic physical properties of graphite. Excellent consistency is observed between the calculated and experimental phonon dispersions of AB-stacked graphite, showing the validity of the interlayer potentials. More importantly, layer-related properties for nonideal structures (e.g., the exfoliation energy, cleave energy, stacking fault energy, surface energy, etc.) can be easily predicted from the interlayer potentials, which promise to be extremely efficient and helpful in studying van der Waals structures.

The effect of mineral-based alkaline water on hydration status and the metabolic response to short-term anaerobic exercise

PubMed Central

Chycki, Jakub; Zając, Tomasz; Kurylas, Anna

2017-01-01

Previously it was demonstrated that mineralization and alkalization properties of mineral water are important factors influencing acid-base balance and hydration in athletes. The purpose of this study was to investigate the effects of drinking different types of water on urine pH, specific urine gravity, and post-exercise lactate utilization in response to strenuous exercise. Thirty-six male soccer players were divided into three intervention groups, consuming around 4.0 l/day of different types of water for 7 days: HM (n=12; highly mineralized water), LM (n=12; low mineralized water), and CON (n=12; table water). The athletes performed an exercise protocol on two occasions (before and after intervention). The exercise protocol consisted of 5 bouts of intensive 60-s (120% VO2max) cycling separated by 60 s of passive rest. Body composition, urinalysis and lactate concentration were evaluated – before (t0), immediately after (t1), 5’ (t2), and 30’ (t3) after exercise. Total body water and its active transport (TBW – total body water / ICW – intracellular water / ECW – extracellular water) showed no significant differences in all groups, at both occasions. In the post-hydration state we found a significant decrease of specific urine gravity in HM (1021±4.2 vs 1015±3.8 g/L) and LM (1022±3.1 vs 1008±4.2 g/L). We also found a significant increase of pH and lactate utilization rate in LM. In conclusion, the athletes hydrated with alkaline, low mineralized water demonstrated favourable changes in hydration status in response to high-intensity interval exercise with a significant decrease of specific urine gravity, increased urine pH and more efficient utilization of lactate after supramaximal exercise. PMID:29158619

Interlayer‐State‐Coupling Dependent Ultrafast Charge Transfer in MoS2/WS2 Bilayers

PubMed Central

Zhang, Jin; Hong, Hao; Lian, Chao; Ma, Wei; Xu, Xiaozhi; Zhou, Xu; Fu, Huixia

2017-01-01

Light‐induced interlayer ultrafast charge transfer in 2D heterostructures provides a new platform for optoelectronic and photovoltaic applications. The charge separation process is generally hypothesized to be dependent on the interlayer stackings and interactions, however, the quantitative characteristic and detailed mechanism remain elusive. Here, a systematical study on the interlayer charge transfer in model MoS2/WS2 bilayer system with variable stacking configurations by time‐dependent density functional theory methods is demonstrated. The results show that the slight change of interlayer geometry can significantly modulate the charge transfer time from 100 fs to 1 ps scale. Detailed analysis further reveals that the transfer rate in MoS2/WS2 bilayers is governed by the electronic coupling between specific interlayer states, rather than the interlayer distances, and follows a universal dependence on the state‐coupling strength. The results establish the interlayer stacking as an effective freedom to control ultrafast charge transfer dynamics in 2D heterostructures and facilitate their future applications in optoelectronics and light harvesting. PMID:28932669

Dispersion relations of elastic waves in one-dimensional piezoelectric/piezomagnetic phononic crystal with functionally graded interlayers.

PubMed

Guo, Xiao; Wei, Peijun; Lan, Man; Li, Li

2016-08-01

The effects of functionally graded interlayers on dispersion relations of elastic waves in a one-dimensional piezoelectric/piezomagnetic phononic crystal are studied in this paper. First, the state transfer equation of the functionally graded interlayer is derived from the motion equation by the reduction of order (from second order to first order). The transfer matrix of the functionally graded interlayer is obtained by solving the state transfer equation with the spatial-varying coefficient. Based on the transfer matrixes of the piezoelectric slab, the piezomagnetic slab and the functionally graded interlayers, the total transfer matrix of a single cell is obtained. Further, the Bloch theorem is used to obtain the resultant dispersion equations of in-plane and anti-plane Bloch waves. The dispersion equations are solved numerically and the numerical results are shown graphically. Five kinds of profiles of functionally graded interlayers between a piezoelectric slab and a piezomagnetic slab are considered. It is shown that the functionally graded interlayers have evident influences on the dispersion curves and the band gaps. Copyright © 2016 Elsevier B.V. All rights reserved.

The impact of fire suppression tasks on firefighter hydration: a critical review with consideration of the utility of reported hydration measures.

PubMed

Walker, Adam; Pope, Rodney; Orr, Robin Marc

2016-01-01

Firefighting is a highly stressful occupation with unique physical challenges, apparel and environments that increase the potential for dehydration. Dehydration leaves the firefighter at risk of harm to their health, safety and performance. The purpose of this review was to critically analyse the current literature investigating the impact of fighting 'live' fires on firefighter hydration. A systematic search was performed of four electronic databases for relevant published studies investigating the impact of live fire suppression on firefighter hydration. Study eligibility was assessed using strict inclusion and exclusion criteria. The included studies were critically appraised using the Downs and Black protocol and graded according to the Kennelly grading system. Ten studies met the eligibility criteria for this review. The average score for methodological quality was 55 %, ranging from 50 % ('fair' quality) to 61 % ('good' quality) with a 'substantial agreement' between raters ( k  = .772). Wildfire suppression was considered in five studies and structural fire suppression in five studies. Results varied across the studies, reflecting variations in outcome measures, hydration protocols and interventions. Three studies reported significant indicators of dehydration resulting from structural fire suppression, while two studies found mixed results, with some measures indicating dehydration and other measures an unchanged hydration status. Three studies found non-significant changes in hydration resulting from wildfire firefighting and two studies found significant improvements in markers of hydration. Ad libitum fluid intake was a common factor across the studies finding no, or less severe, dehydration. The evidence confirms that structural and wildfire firefighting can cause dehydration. Ad libitum drinking may be sufficient to maintain hydration in many wildfire environments but possibly not during intense, longer duration, hot structural fire operations. Future high quality research better quantifying the effects of these influences on the degree of dehydration is required to inform policies and procedures that ensure firefighter health and safety.

The impact of the peritoneal glucose load index on hydration status and inflammation in peritoneal dialysis patients.

PubMed

Hassan, Kamal; Hassan, Fadi; Edgem, Rabia; Moshe, Smadar; Hassan, Shadi

2015-02-01

To evaluate the impact of the peritoneal glucose load (PGL) on hydration status and inflammation in peritoneal dialysis (PD) patients. This cross-sectional study evaluated stable PD patients using a novel PGL index (PGLI), which was calculated as the net glucose content (g) in the PD solutions administered in the daily PD prescription divided by the dry body weight (kg) assessed by whole-body bioimpedance spectroscopy. The relationship between PGLI and glycosylated haemoglobin (HbA1c), fluid overload (FO), and inflammatory markers was investigated. A total of 43 stable PD patients participated in the study. Significant positive correlations were found between PGLI and HbA1c, FO, plasma high sensitivity C-reactive protein (hsCRP), and plasma interleukin-6 (IL-6) levels. HbA1c, FO, plasma hsCRP and plasma IL-6 levels were significantly higher in patients with PGLI >3 g/kg/day compared with those with PGLI ≤3 g/kg/day. PGLI values >3 g/kg/day may be associated with poor glycaemic control, over hydration and augmented inflammation. PGLI might be a useful tool for the quantitative assessment of the PGL and could be applied when managing PD patients. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Maximizing synchronizability of duplex networks

NASA Astrophysics Data System (ADS)

Wei, Xiang; Emenheiser, Jeffrey; Wu, Xiaoqun; Lu, Jun-an; D'Souza, Raissa M.

2018-01-01

We study the synchronizability of duplex networks formed by two randomly generated network layers with different patterns of interlayer node connections. According to the master stability function, we use the smallest nonzero eigenvalue and the eigenratio between the largest and the second smallest eigenvalues of supra-Laplacian matrices to characterize synchronizability on various duplexes. We find that the interlayer linking weight and linking fraction have a profound impact on synchronizability of duplex networks. The increasingly large inter-layer coupling weight is found to cause either decreasing or constant synchronizability for different classes of network dynamics. In addition, negative node degree correlation across interlayer links outperforms positive degree correlation when most interlayer links are present. The reverse is true when a few interlayer links are present. The numerical results and understanding based on these representative duplex networks are illustrative and instructive for building insights into maximizing synchronizability of more realistic multiplex networks.

Influence of in-situ deposited SiNx interlayer on crystal quality of GaN epitaxial films

NASA Astrophysics Data System (ADS)

Fan, Teng; Jia, Wei; Tong, Guangyun; Zhai, Guangmei; Li, Tianbao; Dong, Hailiang; Xu, Bingshe

2018-05-01

GaN epitaxial films with SiNx interlayers were prepared by metal organic chemical vapor deposition (MOCVD) on c-plane sapphire substrates. The influences of deposition times and locations of SiNx interlayers on crystal quality of GaN epitaxial films were studied. Under the optimal growth time of 120 s for the SiNx interlayer, the dislocation density of GaN film is reduced to 4.05 × 108 cm-2 proved by high resolution X-ray diffraction results. It is found that when the SiNx interlayer deposits on the GaN nucleation islands, the subsequent GaN film has the lowest dislocation density of only 2.89 × 108 cm-2. Moreover, a model is proposed to illustrate the morphological evolution and associated propagation processes of TDs in GaN epi-layers with SiNx interlayers for different deposition times and locations.

Voltage-controlled interlayer coupling in perpendicularly magnetized magnetic tunnel junctions

DOE PAGES

Newhouse-Illige, Ty; Liu, Yaohua; Xu, M.; ...

2017-05-16

Magnetic interlayer coupling is one of the central phenomena in spintronics. It has been predicted that the sign of interlayer coupling can be manipulated by electric fields, instead of electric currents, thereby offering a promising low energy magnetization switching mechanism. Here we present the experimental demonstration of voltage-controlled interlayer coupling in a new perpendicular magnetic tunnel junction system with a GdO x tunnel barrier, where a large perpendicular magnetic anisotropy and a sizable tunnelling magnetoresistance have been achieved at room temperature. Owing to the interfacial nature of the magnetism, the ability to move oxygen vacancies within the barrier, and amore » large proximity-induced magnetization of GdO x, both the magnitude and the sign of the interlayer coupling in these junctions can be directly controlled by voltage. Lastly, these results pave a new path towards achieving energy-efficient magnetization switching by controlling interlayer coupling.« less

Voltage-controlled interlayer coupling in perpendicularly magnetized magnetic tunnel junctions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newhouse-Illige, Ty; Liu, Yaohua; Xu, M.

Magnetic interlayer coupling is one of the central phenomena in spintronics. It has been predicted that the sign of interlayer coupling can be manipulated by electric fields, instead of electric currents, thereby offering a promising low energy magnetization switching mechanism. Here we present the experimental demonstration of voltage-controlled interlayer coupling in a new perpendicular magnetic tunnel junction system with a GdO x tunnel barrier, where a large perpendicular magnetic anisotropy and a sizable tunnelling magnetoresistance have been achieved at room temperature. Owing to the interfacial nature of the magnetism, the ability to move oxygen vacancies within the barrier, and amore » large proximity-induced magnetization of GdO x, both the magnitude and the sign of the interlayer coupling in these junctions can be directly controlled by voltage. Lastly, these results pave a new path towards achieving energy-efficient magnetization switching by controlling interlayer coupling.« less

Body composition and hydration status changes in male and female open-water swimmers during an ultra-endurance event.

PubMed

Weitkunat, Tim; Knechtle, Beat; Knechtle, Patrizia; Rüst, Christoph Alexander; Rosemann, Thomas

2012-01-01

Body mass changes during ultra-endurance performances have been described for running, cycling and for swimming in a heated pool. The present field study of 20 male and 11 female open-water swimmers investigated the changes in body composition and hydration status during an ultra-endurance event. Body mass, both estimated fat mass and skeletal muscle mass, haematocrit, plasma sodium concentration ([Na+]) and urine specific gravity were determined. Energy intake, energy expenditure and fluid intake were estimated. Males experienced significant reductions in body mass (-0.5 %) and skeletal muscle mass (-1.1 %) (P < 0.05) during the race compared to females who showed no significant changes with regard to these variables (P > 0.05). Changes in percent body fat, fat mass, and fat-free mass were heterogeneous and did not reach statistical significance (P > 0.05) between gender groups. Fluid intake relative to plasma volume was higher in females than in males during the ultra-endurance event. Compared to males, females' average increase in haematocrit was 3.3 percentage points (pp) higher, urine specific gravity decrease 0.1 pp smaller, and plasma [Na+] 1.3 pp higher. The observed patterns of fluid intake, changes in plasma volume, urine specific gravity, and plasma [Na+] suggest that, particularly in females, a combination of fluid shift from blood vessels to interstitial tissue, facilitated by skeletal muscle damage, as well as exercise-associated hyponatremia had occurred. To summarise, changes in body composition and hydration status are different in male compared to female open-water ultra-endurance swimmers.

Hydration status influences seed fire tolerance in temperate European herbaceous species.

PubMed

Ruprecht, E; Lukács, K; Domokos, P; Kuhn, T; Fenesi, A

2016-03-01

Prescribed burning is an important management tool in many parts of the world. While natural fires generally occur during the driest and warmest period of the year, prescribed burning is often timed out-of-season, when there is higher soil moisture and lower biomass combustibility. However, fire season may influence seedling recruitment after fire, e.g. through the effect of seed hydration status on fire tolerance. In non-fire-prone temperate regions, anthropogenic fire may occur exclusively in periods outside the growing season with higher soil moisture, which may have negative consequences on seedling recruitment. Fire tolerance of moist and dry seeds of 16 temperate European herbaceous species belonging to four families was assessed using heat treatment of 100 °C for 5 min and subsequent germination trials. Moist seeds of Asteraceae, Poaceae and Brassicaceae had a predominantly negative reaction to the heat treatment, while those of Fabaceae tolerated it or germination was even enhanced. The reaction of dry seeds was completely different, with positive responses in three species of the Fabaceae and fire tolerance in species of other families. Our results point out that hydration status may significantly influence the post-fire germination of seeds. Dry seeds were found to tolerate high heat, while moist seeds were harmed in more than half of the species. This implies that if prescribed burning is applied in temperate grasslands of Europe, it should be timed to dry periods of the dormant season in order to protect seeds from negative effects of fire. © 2015 German Botanical Society and The Royal Botanical Society of the Netherlands.

A Cross-Sectional Study on the Association between 24-h Urine Osmolality and Weight Status in Older Adults

PubMed Central

S. Guerra, Rita; Afonso, Cláudia; Moreira, Pedro

2017-01-01

Data on the association between hydration and body weight in the elderly are scarce. The objective of this work was to quantify the association between 24-h urine osmolality and weight status in the elderly. A cross-sectional study was conducted within the Nutrition UP 65 study. A quota sampling was implemented to achieve a nationally representative sample of Portuguese older adults (≥65 years) according to age, sex, education and region. From a sample size of 1500 participants, 1315 were eligible for the present analysis, 57.3% were women and 23.5% were aged ≥80 years. Participants were grouped using tertiles of 24-h urine osmolality by sex. World Health Organization cutoffs were used to classify participants according to weight status. Multinomial multivariable logistic regression models were conducted to evaluate the association of tertiles of osmolality with weight status, adjusting for confounders. Odds Ratios (OR) and respective 95% Confidence Intervals (95% CI) were calculated. Being in the 3rd urine osmolality tertile (highest) was associated with a higher risk of being obese in men, OR = 1.97, 95% CI = 1.06, 3.66. No such association was found in women. These results highlight the need for implementing studies in order to clarify the association between hydration and weight status in the elderly. PMID:29165353

The effect of a competitive wrestling season on body weight, hydration, and muscular performance in collegiate wrestlers.

PubMed

Buford, Thomas W; Rossi, Stephen J; Smith, Douglas B; O'Brien, Matthew S; Pickering, Chris

2006-08-01

The purpose of the present investigation was to examine the effects of a collegiate wrestling season on body weight, hydration, and muscular performance. Twelve Division I collegiate wrestlers (mean +/- SE; 20.75 +/- 0.41 year) volunteered to participate in testing sessions during midseason and 3 weeks following the season. Testing consisted of weigh-in, providing a urine sample for hydration analysis, and a measure of isometric leg extension peak torque. Weight significantly increased (p < 0.05) following the completion of the competitive season. No significant change in urine specific gravity (p > 0.05) was observed. Muscular performance was affected by the season as peak torque (PT) and PT-to-body weight ratio increased significantly (p < 0.05). Following the collegiate wrestling season, augmentation in body weight and muscular performance of the wrestlers occurs without alterations in hydration status. Further research is warranted on what type of strength training program would most effectively reduce the decrements in strength associated with weight loss and the strain of a competitive season.

Dehydration, skeletal muscle damage and inflammation before the competitions among the elite wrestlers

PubMed Central

Ozkan, Isik; Ibrahim, Cicioglu H.

2016-01-01

[Purpose] The present study aimed to identify weight-loss and hydration levels before competitions among elite wrestlers and determine the skeletal muscle damage and inflammation levels after dehydration. [Subjects] Seventy-two elite wrestlers who participated in the Turkish Wrestling Championship. [Methods] With the help of specialists, 5 cc of blood were drawn from the forearm veins of the wrestlers. Laboratory analyses of Na+, BUN, Glucose, CK, LDH, AST, ALT, C-RP levels were performed. Using a mathematical formula for hydration the POsm levels of the athletes were calculated. [Results] The wrestlers were divided into two groups based on hydration status. There were significant correlations between hydration indicators of Na+, BUN and PBWL values. There were significant differences between AST, LDH, CK values and skeletal muscle damage indicators of the two groups, but there were no significant differences between the inflammation levels and C-RP values of the groups. [Conclusion] No differences existed in inflammation levels among the wrestlers, although dehydrated wrestlers suffered from higher level of skeletal muscle damage than wrestlers who were not dehydrated. PMID:26957750

Accuracy of prediction equations for serum osmolarity in frail older people with and without diabetes1234

PubMed Central

Siervo, Mario; Bunn, Diane; Prado, Carla M; Hooper, Lee

2014-01-01

Background: Serum osmolality is an accurate indicator of hydration status in older adults. Glucose, urea, and electrolyte concentrations are used to calculate serum osmolarity, which is an indirect estimate of serum osmolality, but which serum osmolarity equations best predict serum osmolality in the elderly is unclear. Objective: We assessed the agreement of measured serum osmolality with calculated serum osmolarity equations in older people. Design: Serum osmolality was measured by using freezing point depression in a cross-sectional study. Plasma glucose, urea, and electrolytes were analyzed and entered into 38 serum osmolarity-prediction equations. The Bland-Altman method was used to evaluate the agreement and differential bias between measured osmolality and calculated osmolarity. The sensitivity and specificity of the most-promising equations were examined against serum osmolality (reference standard). Results: A total of 186 people living in UK residential care took part in the Dehydration Recognition In our Elders study (66% women; mean ± SD age: 85.8 ± 7.9 y; with a range of cognitive and physical impairments) and were included in analyses. Forty-six percent of participants had impending or current dehydration (serum osmolality ≥295 mmol/kg). Participants with diabetes (n = 33; 18%) had higher glucose (P < 0.001) and serum osmolality (P < 0.01). Of 38 predictive equations used to calculate osmolarity, 4 equations showed reasonable agreement with measured osmolality. One [calculated osmolarity = 1.86 × (Na+ + K+) + 1.15 × glucose + urea +14; all in mmol/L] was characterized by narrower limits of agreement and the capacity to predict serum osmolality within 2% in >80% of participants, regardless of diabetes or hydration status. The equation's sensitivity (79%) and specificity (89%) for impending dehydration (≥295 mmol/kg) and current dehydration (>300 mmol/kg) (69% and 93%, respectively) were reasonable. Conclusions: The assessment of a panel of equations for the prediction of serum osmolarity led to identification of one formula with a greater diagnostic performance. This equation may be used to predict hydration status in frail older people (as a first-stage screening) or to estimate hydration status in population studies. This trial was registered at the Research Register for Social Care (http://www.researchregister.org.uk) as 122273. PMID:25030781

Performance of TenCate Paving interlayers in asphalt concrete pavements.

DOT National Transportation Integrated Search

2017-08-01

As a continued effort of a previously completed project entitled Performance of TenCate Mirafi PGM-G4 Interlayer-Reinforced Asphalt Pavements in Alaska, this project evaluated two newly modified paving interlayers (TruPave and Mirapave) through...

Variable Temperature Infrared Spectroscopy Investigation of Benzoic Acid Interactions with Montmorillonite Clay Interlayer Water.

PubMed

Nickels, Tara M; Ingram, Audrey L; Maraoulaite, Dalia K; White, Robert L

2015-07-01

Molecular interactions between benzoic acid and cations and water contained in montmorillonite clay interlayer spaces are characterized by using variable temperature diffuse reflection infrared Fourier transform spectroscopy (VT-DRIFTS). Using sample perturbation and difference spectroscopy, infrared spectral changes resulting from removal of interlayer water and associated changes in local benzoic acid environments are identified. Difference spectra features can be correlated with changes in specific molecular vibrations that are characteristic of benzoic acid molecular orientation. Results suggest that the carboxylic acid functionality of benzoic acid interacts with interlayer cations through a bridging water molecule and that this interaction is affected by the nature of the cation present in the clay interlayer space.

Bending stiffness and interlayer shear modulus of few-layer graphene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Xiaoming; Yi, Chenglin; Ke, Changhong, E-mail: cke@binghamton.edu

2015-03-09

Interlayer shear deformation occurs in the bending of multilayer graphene with unconstrained ends, thus influencing its bending rigidity. Here, we investigate the bending stiffness and interlayer shear modulus of few-layer graphene through examining its self-folding conformation on a flat substrate using atomic force microscopy in conjunction with nonlinear mechanics modeling. The results reveal that the bending stiffness of 2–6 layers graphene follows a square-power relationship with its thickness. The interlayer shear modulus is found to be in the range of 0.36–0.49 GPa. The research findings show that the weak interlayer shear interaction has a substantial stiffening effect for multilayer graphene.

Interface amorphization in hexagonal boron nitride films on sapphire substrate grown by metalorganic vapor phase epitaxy

NASA Astrophysics Data System (ADS)

Yang, Xu; Nitta, Shugo; Pristovsek, Markus; Liu, Yuhuai; Nagamatsu, Kentaro; Kushimoto, Maki; Honda, Yoshio; Amano, Hiroshi

2018-05-01

Hexagonal boron nitride (h-BN) films directly grown on c-plane sapphire substrates by pulsed-mode metalorganic vapor phase epitaxy exhibit an interlayer for growth temperatures above 1200 °C. Cross-sectional transmission electron microscopy shows that this interlayer is amorphous, while the crystalline h-BN layer above has a distinct orientational relationship with the sapphire substrate. Electron energy loss spectroscopy shows the energy-loss peaks of B and N in both the amorphous interlayer and the overlying crystalline h-BN layer, while Al and O signals are also seen in the amorphous interlayer. Thus, the interlayer forms during h-BN growth through the decomposition of the sapphire at elevated temperatures.

Interlayer exciton optoelectronics in a 2D heterostructure p–n junction

DOE PAGES

Ross, Jason S.; Rivera, Pasqual; Schaibley, John; ...

2016-12-22

Semiconductor heterostructures are backbones for solid-state-based optoelectronic devices. Recent advances in assembly techniques for van der Waals heterostructures have enabled the band engineering of semiconductor heterojunctions for atomically thin optoelectronic devices. In two-dimensional heterostructures with type II band alignment, interlayer excitons, where Coulomb bound electrons and holes are confined to opposite layers, have shown promising properties for novel excitonic devices, including a large binding energy, micron-scale in-plane drift-diffusion, and a long population and valley polarization lifetime. Here, we demonstrate interlayer exciton optoelectronics based on electrostatically defined lateral p–n junctions in a MoSe 2–WSe 2 heterobilayer. Applying a forward bias enablesmore » the first observation of electroluminescence from interlayer excitons. At zero bias, the p–n junction functions as a highly sensitive photodetector, where the wavelength-dependent photocurrent measurement allows the direct observation of resonant optical excitation of the interlayer exciton. The resulting photocurrent amplitude from the interlayer exciton is about 200 times smaller than the resonant excitation of intralayer exciton. This implies that the interlayer exciton oscillator strength is 2 orders of magnitude smaller than that of the intralayer exciton due to the spatial separation of electron and hole to the opposite layers. Lastly, these results lay the foundation for exploiting the interlayer exciton in future 2D heterostructure optoelectronic devices.« less

Quantum-Dot Light-Emitting Diodes with Nitrogen-Doped Carbon Nanodot Hole Transport and Electronic Energy Transfer Layer.

PubMed

Park, Young Ran; Jeong, Hu Young; Seo, Young Soo; Choi, Won Kook; Hong, Young Joon

2017-04-12

Electroluminescence efficiency is crucial for the application of quantum-dot light-emitting diodes (QD-LEDs) in practical devices. We demonstrate that nitrogen-doped carbon nanodot (N-CD) interlayer improves electrical and luminescent properties of QD-LEDs. The N-CDs were prepared by solution-based bottom up synthesis and were inserted as a hole transport layer (HTL) between other multilayer HTL heterojunction and the red-QD layer. The QD-LEDs with N-CD interlayer represented superior electrical rectification and electroluminescent efficiency than those without the N-CD interlayer. The insertion of N-CD layer was found to provoke the Förster resonance energy transfer (FRET) from N-CD to QD layer, as confirmed by time-integrated and -resolved photoluminescence spectroscopy. Moreover, hole-only devices (HODs) with N-CD interlayer presented high hole transport capability, and ultraviolet photoelectron spectroscopy also revealed that the N-CD interlayer reduced the highest hole barrier height. Thus, more balanced carrier injection with sufficient hole carrier transport feasibly lead to the superior electrical and electroluminescent properties of the QD-LEDs with N-CD interlayer. We further studied effect of N-CD interlayer thickness on electrical and luminescent performances for high-brightness QD-LEDs. The ability of the N-CD interlayer to improve both the electrical and luminescent characteristics of the QD-LEDs would be readily exploited as an emerging photoactive material for high-efficiency optoelectronic devices.

Evaluation of stone/RAP interlayers under accelerated loading : technical summary.

DOT National Transportation Integrated Search

2008-08-01

The primary objective of this study was to determine the effectiveness of using an untreated RAP interlayer in lieu of a stone interlayer in a soil-cement asphalt pavement structure under accelerated loading. The secondary objective was to investigat...

Structural evolution of Ti destroyable interlayer in large-size diamond film deposition by DC arc plasma jet

NASA Astrophysics Data System (ADS)

Guo, Jianchao; Li, Chengming; Liu, Jinlong; Wei, Junjun; Chen, Liangxian; Hua, Chenyi; Yan, Xiongbo

2016-05-01

The addition of titanium (Ti) interlayer was verified to reduce the residual stress of diamond films by self-fracturing and facilitate the harvest of a crack-free free-standing diamond film prepared by direct current (DC) arc plasma jet. In this study, the evolution of the Ti interlayer between large-area diamond film and substrate was studied and modeled in detail. The evolution of the interlayer was found to be relevant to the distribution of the DC arc plasma, which can be divided into three areas (arc center, arc main, and arc edge). The formation rate of titanium carbide (TiC) in the arc main was faster than in the other two areas and resulted in the preferred generation of crack in the diamond film in the arc main during cooling. Sandwich structures were formed along with the growth of TiC until the complete transformation of the Ti interlayer. The interlayer released stress via self-fracture. Avoiding uneven fragile regions that formed locally in the interlayer and achieving cooperatively released stress are crucial for the preparation of large crack-free diamond films.

Enhanced performance of solution-processed organic thin-film transistors with a low-temperature-annealed alumina interlayer between the polyimide gate insulator and the semiconductor.

PubMed

Yoon, Jun-Young; Jeong, Sunho; Lee, Sun Sook; Kim, Yun Ho; Ka, Jae-Won; Yi, Mi Hye; Jang, Kwang-Suk

2013-06-12

We studied a low-temperature-annealed sol-gel-derived alumina interlayer between the organic semiconductor and the organic gate insulator for high-performance organic thin-film transistors. The alumina interlayer was deposited on the polyimide gate insulator by a simple spin-coating and 200 °C-annealing process. The leakage current density decreased by the interlayer deposition: at 1 MV/cm, the leakage current densities of the polyimide and the alumina/polyimide gate insulators were 7.64 × 10(-7) and 3.01 × 10(-9) A/cm(2), respectively. For the first time, enhancement of the organic thin-film transistor performance by introduction of an inorganic interlayer between the organic semiconductor and the organic gate insulator was demonstrated: by introducing the interlayer, the field-effect mobility of the solution-processed organic thin-film transistor increased from 0.35 ± 0.15 to 1.35 ± 0.28 cm(2)/V·s. Our results suggest that inorganic interlayer deposition could be a simple and efficient surface treatment of organic gate insulators for enhancing the performance of solution-processed organic thin-film transistors.

Effects of Electrospun Carbon Nanofibers' Interlayers on High-Performance Lithium-Sulfur Batteries.

PubMed

Gao, Tianji; Le, TrungHieu; Yang, Ying; Yu, Zhihao; Huang, Zhenghong; Kang, Feiyu

2017-03-31

Two different interlayers were introduced in lithium-sulfur batteries to improve the cycling stability with sulfur loading as high as 80% of total mass of cathode. Melamine was recommended as a nitrogen-rich (N-rich) amine component to synthesize a modified polyacrylic acid (MPAA). The electrospun MPAA was carbonized into N-rich carbon nanofibers, which were used as cathode interlayers, while carbon nanofibers from PAA without melamine was used as an anode interlayer. At the rate of 0.1 C, the initial discharge capacity with two interlayers was 983 mAh g -1 , and faded down to 651 mAh g -1 after 100 cycles with the coulombic efficiency of 95.4%. At the rate of 1 C, the discharge capacity was kept to 380 mAh g -1 after 600 cycles with a coulombic efficiency of 98.8%. It apparently demonstrated that the cathode interlayer is extremely effective at shutting down the migration of polysulfide ions. The anode interlayer induced the lithium ions to form uniform lithium metal deposits confined on the fiber surface and in the bulk to strengthen the cycling stability of the lithium metal anode.

High-Performance Lithium-Sulfur Batteries with a Self-Assembled Multiwall Carbon Nanotube Interlayer and a Robust Electrode-Electrolyte Interface.

PubMed

Kim, Hee Min; Hwang, Jang-Yeon; Manthiram, Arumugam; Sun, Yang-Kook

2016-01-13

Elemental sulfur electrode has a huge advantage in terms of charge-storage capacity. However, the lack of electrical conductivity results in poor electrochemical utilization of sulfur and performance. This problem has been overcome to some extent previously by using a bare multiwall carbon nanotube (MWCNT) paper interlayer between the sulfur cathode and the polymeric separator, resulting in good electron transport and adsorption of dissolved polysulfides. To advance the interlayer concept further, we present here a self-assembled MWCNT interlayer fabricated by a facile, low-cost process. The Li-S cells fabricated with the self-assembled MWCNT interlayer and a high loading of 3 mg cm(-2) sulfur exhibit a first discharge specific capacity of 1112 mAh g(-1) at 0.1 C rate and retain 95.8% of the capacity at 0.5 C rate after 100 cycles as the self-assembled MWCNT interlayer facilitates good interfacial contact between the interlayer and the sulfur cathode and fast electron and lithium-ion transport while trapping and reutilizing the migrating polysulfides. The approach presented here has the potential to advance the commercialization feasibility of the Li-S batteries.

Effects of Electrospun Carbon Nanofibers’ Interlayers on High-Performance Lithium–Sulfur Batteries

PubMed Central

Gao, Tianji; Le, TrungHieu; Yang, Ying; Yu, Zhihao; Huang, Zhenghong; Kang, Feiyu

2017-01-01

Two different interlayers were introduced in lithium–sulfur batteries to improve the cycling stability with sulfur loading as high as 80% of total mass of cathode. Melamine was recommended as a nitrogen-rich (N-rich) amine component to synthesize a modified polyacrylic acid (MPAA). The electrospun MPAA was carbonized into N-rich carbon nanofibers, which were used as cathode interlayers, while carbon nanofibers from PAA without melamine was used as an anode interlayer. At the rate of 0.1 C, the initial discharge capacity with two interlayers was 983 mAh g−1, and faded down to 651 mAh g−1 after 100 cycles with the coulombic efficiency of 95.4%. At the rate of 1 C, the discharge capacity was kept to 380 mAh g−1 after 600 cycles with a coulombic efficiency of 98.8%. It apparently demonstrated that the cathode interlayer is extremely effective at shutting down the migration of polysulfide ions. The anode interlayer induced the lithium ions to form uniform lithium metal deposits confined on the fiber surface and in the bulk to strengthen the cycling stability of the lithium metal anode. PMID:28772731

Stability and Process of Destruction of Compressed Plate of Layered Composite Materials With Defects

NASA Astrophysics Data System (ADS)

Bokhoeva, L. A.; Rogov, V. E.; Chermoshentseva, A. S.; Lobanov, D. V.

2016-08-01

Interlayer defects in composite materials are a pressing problem, which affecting their performance characteristics. In this research, we considered the problem of the stability and of the fracture process of the compressed thin plate made of laminated composite materials with the interlayer defects. In this research we had got a critical equation for a plate with interlayer defect. The experiment showed the effect and the quantity of nano-dispersed additives on the mechanical properties of composite materials with interlayer defects.

Design and development of an impedimetric-based system for the remote monitoring of home-based dialysis patients.

PubMed

Montalibet, Amalric; Arkouche, Walid; Bogónez Franco, Paco; Bonnet, Stéphane; Clarion, Antoine; Delhomme, Georges; Géhin, Claudine; Gharbi, Sadok; Guillemaud, Régis; Jallon, Pierre; Massot, Bertrand; Pham, Pascale; Ribbe-Cornet, Eva; McAdams, Eric

2016-01-01

A key clinical challenge is to determine the desired 'dry weight' of a patient in order to terminate the dialysis procedure at the optimal moment and thus avoid the effects of over- and under-hydration. It has been found that the effects of haemodialysis on patients can be conveniently monitored using whole-body bioimpedance measurements. The identified need of assessing the hydrational status of patients undergoing haemodialysis at home gave rise to the present Dialydom (DIALYse à DOMicile) project. The aim of the project is to develop a convenient miniaturised impedance monitoring device for localised measurements (on the calf) in order to estimate an impedimetric hydrational index of the home-based patient, and to transmit this and other parameters to a remote clinical site. Many challenges must be overcome to develop a robust and valid home-based device. Some of these are presented in the paper.

Hydration status and diurnal trophic interactions shape microbial community function in desert biocrusts

NASA Astrophysics Data System (ADS)

Kim, Minsu; Or, Dani

2017-12-01

Biological soil crusts (biocrusts) are self-organised thin assemblies of microbes, lichens, and mosses that are ubiquitous in arid regions and serve as important ecological and biogeochemical hotspots. Biocrust ecological function is intricately shaped by strong gradients of water, light, oxygen, and dynamics in the abundance and spatial organisation of the microbial community within a few millimetres of the soil surface. We report a mechanistic model that links the biophysical and chemical processes that shape the functioning of biocrust representative microbial communities that interact trophically and respond dynamically to cycles of hydration, light, and temperature. The model captures key features of carbon and nitrogen cycling within biocrusts, such as microbial activity and distribution (during early stages of biocrust establishment) under diurnal cycles and the associated dynamics of biogeochemical fluxes at different hydration conditions. The study offers new insights into the highly dynamic and localised processes performed by microbial communities within thin desert biocrusts.

Inhibition of hyaluronan synthesis in rats reduces renal ability to excrete fluid and electrolytes during acute hydration

PubMed Central

Stridh, Sara; Palm, Fredrik

2013-01-01

Background. Hyaluronan (HA) is the dominant glycosaminoglycan in the renomedullary interstitium. Renomedullary HA has been implicated in tubular fluid handling due to its water-attracting properties and the changes occurring in parallel to acute variations in the body hydration status. Methods. HA production was inhibited by 4-methylumbelliferone (4-MU in drinking water for 5 days, 1.45 ± 0.07 g/day/kg body weight) in rats prior to hydration. Results. Following hypotonic hydration for 135 min in control animals, diuresis and osmotic excretion increased while sodium excretion and glomerular filtration rate (GFR) remained unchanged. The medullary and cortical HA contents were 7.85 ± 1.29 ng/mg protein and 0.08 ± 0.01 ng/mg protein, respectively. Medullary HA content after 4-MU was 38% of that in controls (2.98 ± 0.95 ng/g protein, p < 0.05), while the low cortical levels were unaffected. Baseline urine flow was not different from that in controls. The diuretic response to hydration was, however, only 51% of that in controls (157 ± 36 versus 306 ± 54 µl/g kidney weight/135 min, p < 0.05) and the osmolar excretion only 47% of that in controls (174 ± 47 versus 374 ± 41 µOsm/g kidney weight/135 min, p < 0.05). Sodium excretion, GFR, and arterial blood pressure were similar to that in control rats and unaltered during hydration. Conclusions. Reduction of renomedullary interstitial HA using 4-MU reduces the ability of the kidney to respond appropriately upon acute hydration. The results strengthen the concept of renomedullary HA as a modulator of tubular fluid handling by changing the physicochemical properties of the interstitial space. PMID:24102146

Comparison of rescue techniques for failed chloral hydrate sedation for magnetic resonance imaging scans--additional chloral hydrate vs intranasal dexmedetomidine.

PubMed

Zhang, Wenhua; Wang, Zixin; Song, Xingrong; Fan, Yanting; Tian, Hang; Li, Bilian

2016-03-01

Chloral hydrate, a commonly used sedative in children during noninvasive diagnostic procedures, is associated with side effects like prolonged sedation, paradoxical excitement, delirium, and unpleasant taste. Dexmedetomidine, a highly selective α-2 agonist, has better pharmacokinetic properties than chloral hydrate. We conducted this prospective, double-blind, randomized controlled trial to evaluate efficacy of intranasal dexmedetomidine with that of a second oral dose of chloral hydrate for rescue sedation during magnetic resonance imaging (MRI) studies in infants. One hundred and fifty infants (age group: 1-6 months), who were not adequately sedated after initial oral dose of 50 mg · kg(-1) chloral hydrate, were randomly divided into three groups with the following protocol for each group. Group C: second oral dose chloral hydrate 25 mg · kg(-1); Group L and Group H: intranasal dexmedetomidine in a dosage of 1 and 2 mcg · kg(-1), respectively. Status of sedation, induction time, time to wake up, vital signs, oxygen saturation, and recovery characteristics were recorded. Successful rescue sedation in Groups C, L, and H were achieved in 40 (80%), 47 (94%), and 49 (98%) of infants, respectively, on an intention to treat analysis, and the proportion of infants successfully sedated in Group H was more than that of Group L (P ˂ 0.01). There were no significant differences in sedation induction time; however, the time to wake up was significantly shorter in Group L as compared to that in Group C or H (P < 0.01). No significant adverse hemodynamic or hypoxemic effects were observed in the study. Intranasal dexmedetomidine induced satisfactory rescue sedation in 1- to 6-month-old infants during MRI study, and appears to cause sedation in a dose-dependent manner. © 2015 John Wiley & Sons Ltd.

Preparation and Bond Properties of Thermal Barrier Coatings on Mg Alloy with Sprayed Al or Diffused Mg-Al Intermetallic Interlayer

NASA Astrophysics Data System (ADS)

Fan, Xizhi; Wang, Ying; Zou, Binglin; Gu, Lijian; Huang, Wenzhi; Cao, Xueqiang

2014-02-01

Sprayed Al or diffused Mg-Al layer was designed as interlayer between the thermal barrier coatings (TBCs) and Mg alloy substrate. The effects of the interlayer on the bond properties of the coats were investigated. Al layers were prepared by arc spraying and atmospheric plasma spraying (APS), respectively. Mg-Al diffused layer was obtained after the heat treatment of the sprayed sample (Mg alloy with APS Al coat) at 400 °C. The results show that sprayed Al interlayer does not improve the bond stability of TBCs. The failure of the TBCs on Mg alloy with Al interlayer occurs mainly due to the low strength of Al layer. Mg-Al diffused layer improves corrosion resistance of substrate and the bond interface. The TBCs on Mg alloy with Mg-Al diffused interlayer shows better bond stability than the sample of which the TBCs is directly sprayed on Mg alloy substrate by APS.

Mechanism Responsible for Intercalation of Dimethyl Sulfoxide in Kaolinite: Molecular Dynamics Simulations.

PubMed

Zhang, Shuai; Liu, Qinfu; Cheng, Hongfei; Gao, Feng; Liu, Cun; Teppen, Brian J

2018-01-01

Intercalation is the promising strategy to expand the interlayer region of kaolinite for their further applications. Herein, the adaptive biasing force (ABF) accelerated molecular dynamics simulations were performed to calculate the free energies involved in the kaolinite intercalation by dimethyl sulfoxide (DMSO). Additionally, the classical all atom molecular dynamics simulations were carried out to calculate the interfacial interactions between kaolinite interlayer surfaces and DMSO with the aim at exploring the underlying force that drives the DMSO to enter the interlayer space. The results showed that the favorable interaction of DMSO with both kaolinite interlayer octahedral surface and tetrahedral surface can help in introducing DMSO enter kaolinite interlayer. The hydroxyl groups on octahedral surface functioned as H-donors attracting the S=O groups of DMSO through hydrogen bonding interaction. The tetrahedral surface featuring hydrophobic property attracted the methyl groups of DMSO through hydrophobic interaction. The results provided a detailed picture of the energetics and interlayer structure of kaolinite-DMSO intercalate.

Interlayer orientation-dependent light absorption and emission in monolayer semiconductor stacks

PubMed Central

Heo, Hoseok; Sung, Ji Ho; Cha, Soonyoung; Jang, Bo-Gyu; Kim, Joo-Youn; Jin, Gangtae; Lee, Donghun; Ahn, Ji-Hoon; Lee, Myoung-Jae; Shim, Ji Hoon; Choi, Hyunyong; Jo, Moon-Ho

2015-01-01

Two-dimensional stacks of dissimilar hexagonal monolayers exhibit unusual electronic, photonic and photovoltaic responses that arise from substantial interlayer excitations. Interband excitation phenomena in individual hexagonal monolayer occur in states at band edges (valleys) in the hexagonal momentum space; therefore, low-energy interlayer excitation in the hexagonal monolayer stacks can be directed by the two-dimensional rotational degree of each monolayer crystal. However, this rotation-dependent excitation is largely unknown, due to lack in control over the relative monolayer rotations, thereby leading to momentum-mismatched interlayer excitations. Here, we report that light absorption and emission in MoS2/WS2 monolayer stacks can be tunable from indirect- to direct-gap transitions in both spectral and dynamic characteristics, when the constituent monolayer crystals are coherently stacked without in-plane rotation misfit. Our study suggests that the interlayer rotational attributes determine tunable interlayer excitation as a new set of basis for investigating optical phenomena in a two-dimensional hexagonal monolayer system. PMID:26099952

Strain modulation-enhanced Mg acceptor activation efficiency of Al0.14Ga0.86N/GaN superlattices with AlN interlayer

NASA Astrophysics Data System (ADS)

Wang, Lei; Li, Rui; Li, Ding; Liu, Ningyang; Liu, Lei; Chen, Weihua; Wang, Cunda; Yang, Zhijian; Hu, Xiaodong

2010-02-01

AlN layer was grown as interlayer between undoped GaN and Mg doped Al0.14Ga0.86N/GaN superlattices (SLs) epilayer to modulate the strain distribution between Al0.14Ga0.86N barrier and GaN well layers in SLs sample. Strain relaxation was observed in the SLs sample with AlN interlayer by x-ray diffraction reciprocal space mapping method. The measured hole concentration of SLs sample with AlN interlayer at room temperature was over 1.6×1018 cm-3 but that was only 6.6×1016 cm-3 obtained in SLs sample without AlN interlayer. Variable temperature Hall-effect measurement showed that the acceptor activation energy decreased from 150 to 70 meV after inserting the AlN layer, which indicated that the strain modulation of SLs induced by AlN interlayer was beneficial to the Mg acceptor activation and hole concentration enhancement.

Intercalation of gaseous thiols and sulfides into Ag+ ion-exchanged aluminum dihydrogen triphosphate.

PubMed

Hayashi, Aki; Saimen, Hiroki; Watanabe, Nobuaki; Kimura, Hitomi; Kobayashi, Ayumi; Nakayama, Hirokazu; Tsuhako, Mitsutomo

2005-08-02

Ag(+) ion-exchanged layered aluminum dihydrogen triphosphate (AlP) with the interlayer distance of 0.85 nm was synthesized by the ion-exchange of proton in triphosphate with Ag(+) ion. The amount of exchanged Ag(+) ion depended on the concentration of AgNO(3) aqueous solution. Ag(+) ion-exchanged AlP adsorbed gaseous thiols and sulfides into the interlayer region. The adsorption amounts of thiols were more than those of sulfides, thiols with one mercapto group > thiol with two mercapto groups > sulfides, and depended on the amount of exchanged Ag(+) ion in the interlayer region. The thiols with one mercapto group were intercalated to expand the interlayer distance of Ag(+) ion-exchanged AlP, whereas there was no expansion in the adsorption of sulfide. In the case of thiol with two mercapto groups, there was observed contraction of the interlayer distance through the bridging with Ag(+) ions of the upper and lower sides of the interlayer region.

Evidence for Interlayer Collapse of Nontronite on Mars from Laboratory Visible and Near-IR Reflective Spectra

NASA Technical Reports Server (NTRS)

Morris, Richard V.; Ming, D. W.; Golden, D. C.; Graff, T. G.; Achilles, C. N.

2010-01-01

Dioctahedral smectites (e.g., nontronite and montmorillionite) are interpreted to occupy the optical surface of Mars at a number of locations on the basis of spectral features derived from interlayer H2O and MOH (M=Fe(3+)2, Fe(3+)Al, Al2, etc.) as observed by orbiting MRO-CRISM and MEx-OMEGA hyperspectral imaging spectrometers. At wavelengths shorter than approximately 2.7 micrometers, the strongest bands from interlayer H2O occur at approximately 1.4 and 1.9 micrometers from 2v1 and v1+v2, respectively, where v1 and v2 are the fundamental stretching and bending vibrations of the H2O molecule. Smectite MOH vibrations occur near 1.4 micrometers (stretching overtone) and in the region between 2.1 and 2.7 micrometers (stretching + bending combination). Because interlayer H2O can exchange with the martian environment, a number of studies have examined the strength of the interlayer H2O spectral features under Mars-like environmental conditions. The relationship between spectral properties and the underlying crystal structure of the smectites was not determined, and the extent of interlayer H2O removal was not established. We report combined visible and near-IR (VNIR), Mossbauer (MB), and powder X-ray diffraction (XRD) data for samples of the Fe-bearing smectite nontronite where the interlayer was collapsed by complete removal of interlayer H2O.

Evaluation of asphalt rubber membrane interlayer (ARMI) using the University of Florida's composite system interface cracking (CSIC) test.

DOT National Transportation Integrated Search

2012-05-01

Since the late 1970s, FDOT : has applied an interlayer : of Asphalt Rubber : Membrane Interlayer : (ARMI) to asphalt roadway : surfaces. ARMI layers are : constructed by spraying : asphalt rubber binder onto : the asphalt, covering the : layer with n...

Hydration status and fluid intake of urban, underprivileged South African male adolescent soccer players during training.

PubMed

Gordon, Reno Eron; Kassier, Susanna Maria; Biggs, Chara

2015-01-01

Poor hydration compromises performance and heightens the risk of heat stress which adolescents are particularly susceptible to as they produce comparatively larger amount of metabolic heat during exercise. This study determined the hydration status and fluid intake of socio-economically disadvantaged, male adolescent soccer players during training. A pilot study was conducted among 79 soccer players (mean age 15.9 ± 0.8 years; mean BMI 20.2 ± 2.1 kg/m(2)). Hydration status was determined before and after two training sessions, using both urine specific gravity and percent loss of body weight. The type and amount of fluid consumed was assessed during training. A self-administered questionnaire was used to determine the players' knowledge regarding fluid and carbohydrate requirements for soccer training. Players were at risk of developing heat illness during six of the 14 training sessions (60 - 90 minutes in length). Although on average players were slightly dehydrated (1.023 ± 0.006 g/ml) before and after (1.024 ± 0.007 g/ml) training, some were extremely dehydrated before (24%) and after (27%) training. Conversely some were extremely hyperhydrated before (3%) and after training (6%). The mean percent loss of body weight was 0.7 ± 0.7%. The majority did not consume fluid during the first (57.0%) and second (70.9%) training sessions. An average of 216.0 ± 140.0 ml of fluid was consumed during both training sessions. The majority (41.8%) consumed water, while a few (5.1%) consumed pure fruit juice. More than 90% stated that water was the most appropriate fluid to consume before, during and after training. Very few (5.0%) correctly stated that carbohydrate should be consumed before, during and after training. Approximately a quarter were severely dehydrated. Many did not drink or drank insufficient amounts. The players' beliefs regarding the importance of fluid and carbohydrate consumption did not correspond with their practices. A nutrition education programme is needed to educate players on the importance of fluid and carbohydrate to prevent dehydration and ensure appropriate carbohydrate intake.

Hydration Status and Sodium Balance of Endurance Runners Consuming Postexercise Supplements of Varying Nutrient Content.

PubMed

Pryor, J Luke; Johnson, Evan C; Del Favero, Jeffery; Monteleone, Andrew; Armstrong, Lawrence E; Rodriguez, Nancy R

2015-10-01

Postexercise protein and sodium supplementation may aid recovery and rehydration. Preserved beef provides protein and contains high quantities of sodium that may alter performance related variables in runners. The purpose of this study was to determine the effects of consuming a commercial beef product postexercise on sodium and water balance. A secondary objective was to characterize effects of the supplementation protocols on hydration, blood pressure, body mass, and running economy. Eight trained males (age = 22 ± 3 y, VO2max = 66.4 ± 4.2 ml·kg-1·min-1) completed three identical weeks of run training (6 run·wk-1, 45 ± 6 min·run-1, 74 ± 5% HRR). After exercise, subjects consumed either, a beef nutritional supplement (beef jerky; [B]), a standard recovery drink (SRD), or SRD+B in a randomized counterbalanced design. Hydration status was assessed via urinary biomarkers and body mass. No main effects of treatment were observed for 24 hr urine volume (SRD, 1.7 ± 0.5; B, 1.8 ± 0.6; SRD+B, 1.4 ± 0.4 L·d-1), urine specific gravity (1.016 ± 0.005, 1.018 ± 0.006, 1.017 ± 0.006) or body mass (68.4 ± 8.2, 68.3 ± 7.7, 68.2 ± 8.1 kg). No main effect of treatment existed for sodium intake-loss (-713 ± 1486; -973 ± 1123; -980 ± 1220 mg·d-1). Mean arterial pressure (81.0 ± 4.6, 81.1 ± 7.3, 83.8 ± 5.4 mm Hg) and average exercise running economy (VO2: SRD, 47.9 ± 3.2; B, 47.2 ± 2.6; SRD+B, 46.2 ± 3.4 ml·kg-1·min-1) was not affected. Urinary sodium excretion accounted for the daily sodium intake due to the beef nutritional supplement. Findings suggest the commercial beef snack is a viable recovery supplement following endurance exercise without concern for hydration status, performance decrements, or cardiovascular consequences.

Evaluation of asphalt rubber membrane interlayer (ARMI) using the University of Florida's composite system interface cracking (CSIC) test [summary].

DOT National Transportation Integrated Search

2012-01-01

Since the late 1970s, FDOT : has applied an interlayer : of Asphalt Rubber : Membrane Interlayer : (ARMI) to asphalt roadway : surfaces. ARMI layers are : constructed by spraying : asphalt rubber binder onto : the asphalt, covering the : layer with n...

FAST TRACK COMMUNICATION: Interlayer exchange coupling across a ferroelectric barrier

NASA Astrophysics Data System (ADS)

Zhuravlev, M. Ye; Vedyayev, A. V.; Tsymbal, E. Y.

2010-09-01

A new magnetoelectric effect is predicted originating from the interlayer exchange coupling between two ferromagnetic layers separated by an ultrathin ferroelectric barrier. It is demonstrated that ferroelectric polarization switching driven by an external electric field leads to a sizable change in the interlayer exchange coupling. The effect occurs in asymmetric ferromagnet/ferroelectric/ferromagnet junctions due to a change in the electrostatic potential profile across the junction affecting the interlayer coupling. The predicted phenomenon indicates the possibility of switching the magnetic configuration by reversing the polarization of the ferroelectric barrier layer.

In0.15Ga0.85N visible-light metal-semiconductor-metal photodetector with GaN interlayers deposited by pulsed NH3

NASA Astrophysics Data System (ADS)

Wang, Hongxia; Zhang, Xiaohan; Wang, Hailong; Lv, Zesheng; Li, Yongxian; Li, Bin; Yan, Huan; Qiu, Xinjia; Jiang, Hao

2018-05-01

InGaN visible-light metal-semiconductor-metal photodetectors with GaN interlayers deposited by pulsed NH3 were fabricated and characterized. By periodically inserting the GaN thin interlayers, the surface morphology of InGaN active layer is improved and the phase separation is suppressed. At 5 V bias, the dark current reduced from 7.0 × 10-11 A to 7.0 × 10-13 A by inserting the interlayers. A peak responsivity of 85.0 mA/W was measured at 420 nm and 5 V bias, corresponding to an external quantum efficiency of 25.1%. The insertion of GaN interlayers also lead to a sharper spectral response cutoff.

Mechanical characterization and modeling of brazed tungsten and Cu-Cr-Zr alloy using stress relief interlayers

NASA Astrophysics Data System (ADS)

Qu, Dandan; Zhou, Zhangjian; Yum, Youngjin; Aktaa, Jarir

2014-12-01

A rapidly solidified foil-type Ti-Zr based amorphous filler with a melting temperature of 850 °C was used to braze tungsten to Cu-Cr-Zr alloy for water cooled divertors and plasma facing components application. Brazed joints of dissimilar materials suffer from a mismatch in coefficients of thermal expansion. In order to release the residual stress caused by the mismatch, brazed joints of tungsten and Cu-Cr-Zr alloy using different interlayers were studied. The shear strength tests of brazed W/Cu joints show that the average strength of the joint with a W70Cu30 composite plate interlayer reached 119.8 MPa, and the average strength of the joint with oxygen free high conductivity copper (OFHC Cu)/Mo multi-interlayers reached 140.8 MPa, while the joint without interlayer was only 16.6 MPa. Finite element method (FEM) has been performed to investigate the stress distribution and effect of stress relief interlayers. FEM results show that the maximum von Mises stress occurs in the tungsten/filler interface and that the filler suffers the peak residual stresses and becomes the weakest zone. And the use of OFHC Cu/Mo multi-interlayers can reduce the residual stress significantly, which agrees with the mechanical experiment data.

Water balance throughout the adult life span in a German population.

PubMed

Manz, Friedrich; Johner, Simone A; Wentz, Andreas; Boeing, Heiner; Remer, Thomas

2012-06-01

Mild dehydration, defined as a 1-2% loss in body mass caused by fluid deficit, is associated with risks of functional impairments and chronic diseases. Whether water requirements change with increasing age remains unclear. Therefore, the aim of the present investigation is to quantify hydration status and its complex determining factors from young to old adulthood to analyse age-related alterations and to provide a reliable database for the derivation of dietary recommendations. Urine samples collected over a 24 h period and dietary records from 1528 German adults (18-88 years; sub-sample of the first National Food Consumption Survey) were used to calculate water intake (beverages, food and metabolic water) and water excretion parameters (non-renal water losses (NRWL), urine volume, obligatory urine volume) and to estimate hydration status (free-water-reserve) and 'adequate intake (AI)'. Median total water intake (2483 and 2054ml/d, for men and women, respectively (P<0·0001)), decreased with increasing age only in males (P=0·001). Obligatory urine volume increased in both sexes (P<0·0001) due to decreased renal concentration capacity. The latter was balanced by a decrease of NRWL (P<0·05), leaving the free-water-reserve and therefore hydration status almost unchanged. Calculated 'AI' of total water was the same for young (18-24 years) and elderly (≥65 years) adults (2910 and 2265ml/d, for men and women, respectively). The present study is the first population-based examination showing that total water requirements do not change with age although ageing affects several parameters of water metabolism. Reduced sweat loss with increasing age appears to be primarily responsible for this observation.

Effects of Agitation and Storage Temperature on Measurements of Hydration Status.

PubMed

Adams, Heather M; Eberman, Lindsey E; Yeargin, Susan W; Niemann, Andrew J; Mata, Heather L; Dziedzicki, David J

2015-12-01

Hypohydration can have significant implications on normal physiological functions of the body. This study aimed to determine the impact of agitation, storage temperature, and storage time on urine osmolality compared to the criterion control. We used a descriptive diagnostic validity test design. To investigate agitation, we recruited 75 healthy individuals (males = 41, females = 34; mean age = 22 ± 5 years; mean self-reported height = 172 ± 23 cm and mass = 77 ± 17 kg) who provided one or more samples (total = 81). The independent variables were agitation (vortex, hand shaken, no agitation) and temperature (room temperature, freezer, and refrigerator) type. Participants completed informed consent, a health questionnaire and were asked to provide a urine sample, which was split and labeled according to agitation type or storage temperature. Urine osmolality was used to determine hydration status at two time points (within 2 hours [control], 48 hours). We used t-tests to determine the difference between each condition and the control and calculated percent error for each condition. No significant differences for no agitation (t79 = -0.079, P = 0.937), hand shaken (t79 = 1.395, P = 0.167) or vortex mixed (t79 = -0.753, P = 0.453) were identified when compared to the criterion control. No significant differences for room temperature (t82 = -0.720, P = 0.474), refrigerator (t82 = -2.697, P = 0.008) or freezer (t82 = 2.576, P = 0.012) were identified when compared to the criterion control. Our findings suggest agitation of urine specimen is not necessary and samples do not require refrigeration or freezing if assessed within 48 hours. Analysis within two hours of collection is not necessary and samples can be stored for up to 48 hours without impacting the hydration status of the sample.

Ad libitum fluid consumption via self- or external administration.

PubMed

Yeargin, Susan W; Finn, Megan E; Eberman, Lindsey E; Gage, Matthew J; McDermott, Brendon P; Niemann, Andrew

2015-01-01

During team athletic events, athletic trainers commonly provide fluids with water bottles. When a limited number of water bottles exist, various techniques are used to deliver fluids. To determine whether fluid delivered via water-bottle administration influenced fluid consumption and hydration status. Crossover study. Outdoor field (22.2°C ± 3.5°C). Nineteen participants (14 men, 5 women, age = 30 ± 10 years, height = 176 ± 8 cm, mass = 72.5 ± 10 kg) were recruited from the university and local running clubs. The independent variable was fluid delivery with 3 levels: self-administration with mouth-to-bottle direct contact (SA-DC), self-administration with no contact between mouth and bottle (SA-NC), and external administration with no contact between the mouth and the bottle (EA-NC). Participants warmed up for 10 minutes before completing 5 exercise stations, after which an ad libitum fluid break was given, for a total of 6 breaks. We measured the fluid variables of total volume consumed, total number of squirts, and average volume per squirt. Hydration status via urine osmolality and body-mass loss, and perceptual variables for thirst and fullness were recorded. We calculated repeated-measures analyses of variance to assess hydration status, fluid variables, and perceptual measures to analyze conditions across time. The total volume consumed for EA-NC was lower than for SA-DC (P = .001) and SA-NC (P = .001). The total number of squirts for SA-DC was lower than for SA-NC (P = .009). The average volume per squirt for EA-NC was lower than for SA-DC (P = .020) and SA-NC (P = .009). Participants arrived (601.0 ± 21.3 mOsm/L) and remained (622.3 ± 38.3 mOsm/L) hydrated, with no difference between conditions (P = .544); however, the EA-NC condition lost more body mass than did the SA-DC condition (P = .001). There was no main effect for condition on thirst (P = .147) or fullness (P = .475). External administration of fluid decreased total volume consumed via a decreased average volume per squirt. The SA-DC method requires fewer squirts within a specific time frame. Fluid breaks every 15 minutes resulted in maintenance of euhydration; however, loss of body mass was influenced by fluid administration. Athletic trainers should avoid external administration to promote positive hydration behaviors. When fluid is self-administered, individual bottles may be the best clinical practice because more volume can be consumed per squirt.

Preexercise Urine Specific Gravity and Fluid Intake During One-Hour Running in a Thermoneutral Environment – A Randomized Cross-Over Study

PubMed Central

Silva, Rafael P.; Mündel, Toby; Altoé, Janaína L.; Saldanha, Mônica R.; Ferreira, Fabrícia G.; Marins, João C.B.

2010-01-01

Urine specific gravity is often used to assess hydration status. Athletes who are hypohydrated prior to exercise tend to ingest more fluid during the exercise, possibly to compensate for their pre exercise fluid deficit. The purpose of this study was to evaluate the effect of additional fluid intake on fluid balance and gastrointestinal tract comfort during 1h running in a thermoneutral environment when athletes followed their habitual fluid and dietary regimes. Sixteen men and sixteen women ingested a 6% carbohydrate-electrolyte solution immediately prior to exercise and then every 15 minutes during two runs, with a consumption rate of 2 mL.kg-1 (LV, lower volume) or 3 mL.kg-1 (HV, higher volume) body mass. Urine specific gravity and body mass changes were determined before and after the tests to estimate hydration status. During exercise subjects verbally responded to surveys inquiring about gastrointestinal symptoms, sensation of thirst and ratings of perceived exertion. Plasma glucose, heart rate and blood pressure were also evaluated. Men had higher preexercise urine specific gravity than women (1.025 vs. 1.016 g·mL-1 HV; and 1.024 vs. 1.017 g·mL-1 LV) and greater sweat loss (1.21 ± 0.27 L vs. 0.83 ± 0.21 L HV; and 1.18 ± 0.23 L vs. 0.77 ± 0.17 LV). Prevalence of gastrointestinal discomfort increased after 45 min. No significant differences on heart rate, rate of perceived exertion, blood pressure or glycemia was observed with the additional fluid intake. From these results it appears that additional fluid intake reduces body mass loss and thirst sensation. When compared to the men, however, preexercise euhydration was more common in women and an increased fluid intake increases the risk of body mass gain and gastrointestinal discomfort. Key points There seems to be a wide variability in pre-exercise hydration status between male and female and efforts aimed at educating athletes about the importance of pregame hydration must be emphasized. The fluid ingestion during running exercise in a moderate environment reduces body mass loss and thirst sensation, but an increased fluid intake at rates to match the fluid loss might raise the risk of body mass gain in women during prolonged activities. Individual gastric tolerance and familiarization with fluid replacement should be taken into account when providing athletes with strategies for hydration during exercise. PMID:24149642

Individual fluid plans versus ad libitum on hydration status in minor professional ice hockey players.

PubMed

Emerson, Dawn M; Torres-McGehee, Toni M; Emerson, Charles C; LaSalle, Teri L

2017-01-01

Despite exercising in cool environments, ice hockey players exhibit several dehydration risk factors. Individualized fluid plans (IFPs) are designed to mitigate dehydration by matching an individual's sweat loss in order to optimize physiological systems and performance. A randomized control trial was used to examine IFP versus ad libitum fluid ingestion on hydration in 11 male minor professional ice hockey players (mean age = 24.4 ± 2.6 years, height = 183.0 ± 4.6 cm, weight = 92.9 ± 7.8 kg). Following baseline measures over 2 practices, participants were randomly assigned to either control (CON) or intervention (INT) for 10 additional practices. CON participants were provided water and/or carbohydrate electrolyte beverage to drink ad libitum. INT participants were instructed to consume water and an electrolyte-enhanced carbohydrate electrolyte beverage to match sweat and sodium losses. Urine specific gravity, urine color, and percent body mass change characterized hydration status. Total fluid consumed during practice was assessed. INT consumed significantly more fluid than CON (1180.8 ± 579.0 ml vs. 788.6 ± 399.7 ml, p  = 0.002). However, CON participants replaced only 25.4 ± 12.9% of their fluid needs and INT 35.8 ± 17.5%. Mean percent body mass loss was not significantly different between groups and overall indicated minimal dehydration (<1.2% loss). Pre-practice urine specific gravity indicated CON and INT began hypohydrated (mean = 1.024 ± 0.007 and 1.024 ± 0.006, respectively) and experienced dehydration during practice (post = 1.026 ± 0.006 and 1.027 ± 0.005, respectively, p  < 0.001). Urine color increased pre- to post-practice for CON (5 ± 2 to 6 ± 1, p  < 0.001) and INT (5 ± 1 to 6 ± 1, p <  0.001). Participants consistently reported to practice hypohydrated. Ad libitum fluid intake was not significantly different than IFP on hydration status. Based on urine measures, both methods were unsuccessful in preventing dehydration during practice, suggesting practice-only hydration is inadequate to maintain euhydration in this population when beginning hypohydrated.

77 FR 21422 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-10

... the fail-safe interlayer of certain No. 2 and No. 3 glass windows, which could result in loss of the... would hinder the internal or external detailed inspections for fail-safe interlayer cracks, glass pane... this AD only if the non-clear damage hinders the inspection for fail-safe interlayer cracks, glass pane...

Measuring Interlayer Shear Stress in Bilayer Graphene

NASA Astrophysics Data System (ADS)

Wang, Guorui; Dai, Zhaohe; Wang, Yanlei; Tan, PingHeng; Liu, Luqi; Xu, Zhiping; Wei, Yueguang; Huang, Rui; Zhang, Zhong

2017-07-01

Monolayer two-dimensional (2D) crystals exhibit a host of intriguing properties, but the most exciting applications may come from stacking them into multilayer structures. Interlayer and interfacial shear interactions could play a crucial role in the performance and reliability of these applications, but little is known about the key parameters controlling shear deformation across the layers and interfaces between 2D materials. Herein, we report the first measurement of the interlayer shear stress of bilayer graphene based on pressurized microscale bubble loading devices. We demonstrate continuous growth of an interlayer shear zone outside the bubble edge and extract an interlayer shear stress of 40 kPa based on a membrane analysis for bilayer graphene bubbles. Meanwhile, a much higher interfacial shear stress of 1.64 MPa was determined for monolayer graphene on a silicon oxide substrate. Our results not only provide insights into the interfacial shear responses of the thinnest structures possible, but also establish an experimental method for characterizing the fundamental interlayer shear properties of the emerging 2D materials for potential applications in multilayer systems.

Connecting the molecular scale to the continuum scale for diffusion processes in smectite-rich porous media.

PubMed

Bourg, Ian C; Sposito, Garrison

2010-03-15

In this paper, we address the manner in which the continuum-scale diffusive properties of smectite-rich porous media arise from their molecular- and pore-scale features. Our starting point is a successful model of the continuum-scale apparent diffusion coefficient for water tracers and cations, which decomposes it as a sum of pore-scale terms describing diffusion in macropore and interlayer "compartments." We then apply molecular dynamics (MD) simulations to determine molecular-scale diffusion coefficients D(interlayer) of water tracers and representative cations (Na(+), Cs(+), Sr(2+)) in Na-smectite interlayers. We find that a remarkably simple expression relates D(interlayer) to the pore-scale parameter δ(nanopore) ≤ 1, a constrictivity factor that accounts for the lower mobility in interlayers as compared to macropores: δ(nanopore) = D(interlayer)/D(0), where D(0) is the diffusion coefficient in bulk liquid water. Using this scaling expression, we can accurately predict the apparent diffusion coefficients of tracers H(2)0, Na(+), Sr(2+), and Cs(+) in compacted Na-smectite-rich materials.

Lightning Damage of Carbon Fiber/Epoxy Laminates with Interlayers Modified by Nickel-Coated Multi-Walled Carbon Nanotubes

NASA Astrophysics Data System (ADS)

Dong, Qi; Wan, Guoshun; Xu, Yongzheng; Guo, Yunli; Du, Tianxiang; Yi, Xiaosu; Jia, Yuxi

2017-12-01

The numerical model of carbon fiber reinforced polymer (CFRP) laminates with electrically modified interlayers subjected to lightning strike is constructed through finite element simulation, in which both intra-laminar and inter-laminar lightning damages are considered by means of coupled electrical-thermal-pyrolytic analysis method. Then the lightning damage extents including the damage volume and maximum damage depth are investigated. The results reveal that the simulated lightning damages could be qualitatively compared to the experimental counterparts of CFRP laminates with interlayers modified by nickel-coated multi-walled carbon nanotubes (Ni-MWCNTs). With higher electrical conductivity of modified interlayer and more amount of modified interlayers, both damage volume and maximum damage depth are reduced. This work provides an effective guidance to the anti-lightning optimization of CFRP laminates.

Drying-induced atomic structural rearrangements in sodium-based calcium-alumino-silicate-hydrate gel and the mitigating effects of ZrO2 nanoparticles

NASA Astrophysics Data System (ADS)

Yang, Kengran; Özçelik, V. Ongun; Garg, Nishant; Gong, Kai; White, Claire E.

Conventional drying of colloidal materials and gels (including cement) can lead to detrimental effects due to the buildup of internal stresses as water evaporates from the nano/microscopic pores. However, the underlying nanoscopic alterations in these gel materials that are, in part, responsible for macroscopically-measured strain values, especially at low relative humidity, remain a topic of open debate in the literature. In this study, sodium-based calcium-alumino-silicate-hydrate (C-(N)-A-S-H) gel, the major binding phase of silicate-activated blast furnace slag (one type of low-CO$_2$ cement), is investigated from a drying perspective, since it is known to suffer extensively from drying-induced microcracking. By employing in situ synchrotron X-ray total scattering measurements and pair distribution function (PDF) analysis we show that the significant contributing factor to the strain development in this material at extremely low relative humidity (0%) is the local atomic structural rearrangement of the C-(N)-A-S-H gel, including collapse of interlayer spacing and slight disintegration of the gel. Moreover, analysis of the medium range (1.0 - 2.2 nm) ordering in the PDF data reveals that the PDF-derived strain values are in much closer agreement (same order of magnitude) with the macroscopically measured strain data, compared to previous results based on reciprocal space X-ray diffraction data. From a mitigation standpoint, we show that small amounts of ZrO$_2$ nanoparticles are able to actively reinforce the structure of silicate-activated slag during drying, preventing atomic level strains from developing. Mechanistically, these nanoparticles induce growth of a silica-rich gel during drying, which, via density functional theory calculations, we show is attributed to the high surface reactivity of tetragonal ZrO$_2$.

Negative Searches for Evidence of Aqueous Alteration on Asteroid Surfaces

NASA Technical Reports Server (NTRS)

Vilas, F.

2005-01-01

Small bodies in the Solar System preserve evidence of the processes occurring during early Solar System formation, unlike the larger planets that undergo continuous churning of their surfaces. We study these bodies to understand what processes affected different stages of Solar System formation. The action of aqueous alteration (the alteration of material by the interaction of that material with liquid formed by the melting of incorporated ice) of near-subsurface material has been inferred to occur on many asteroids based on the spectrophotometric evidence of phyllosilicates and iron alteration minerals. The definitive indication of aqueous alteration is the 3.0- micron absorption feature attributed to structural hydroxyl (OH) and interlayer and adsorbed water (H2O) in phyllosilicates (clays) (hereafter water of hydration). A weak absorption feature centered near 0.7 microns attributed to an Fe (2+) right arrow Fe (3+) charge transfer transition in oxidized iron in phyllosilicates has been observed in the reflectance spectra and photometry of approximately 50% of the main-belt C-class asteroids. An approximately 85% correlation between this 0.7- micron feature and the 3.0- micron water of hydration absorption feature was found among the low-albedo asteroids. The feature is usually centered near 0.68 microns in asteroid spectra, and ranges in wavelength from approximately 0.57 to 0.83 microns. Serendipitously, three of the Eight Color Asteroid Survey filters the v (0.550 microns), w (0.701 microns), and x (0.853 microns)-bracket this feature well, and can be used to determine the presence of this feature in the reflectance properties of an asteroid, and probe the aqueous alteration history of larger samples of asteroid data. Two efforts to search for evidence of aqueous alteration based on the presence of this 0.7- micron absorption feature are presented here.

FT-IR study of CO 2 interaction with Na-rich montmorillonite

DOE PAGES

Krukowski, Elizabeth G.; Goodman, Angela; Rother, Gernot; ...

2015-05-27

Here, carbon capture, utilization and storage (CCUS) in saline reservoirs in sedimentary formations has the potential to reduce the impact of fossil fuel combustion on climate change by reducing CO 2 emissions to the atmosphere and storing the CO 2 in geologic formations in perpetuity. At pressure and temperature (PT) conditions relevant to CCUS, CO 2 is less dense than the pre-existing brine in the formation, and the more buoyant CO 2 will migrate to the top of the formation where it will be in contact with cap rock. Interactions between clay-rich shale cap rocks and CO 2 are poorlymore » understood at PT conditions appropriate for CCUS in saline formations. In this study, the interaction of CO 2 with clay minerals in the cap rock overlying a saline formation has been examined using Na + exchanged montmorillonite (Mt) (Na +-STx-1) (Na + Mt) as an analog for clay-rich shale. Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy (ATR-FTIR) was used to discern mechanistic information for CO 2 interaction with hydrated (both one- and two-water layers) and relatively dehydrated (both dehydrated layers and one-water layers) Na+-STx-1 at 35 °C and 50 C and CO 2 pressure from 0 5.9 MPa. CO 2-induced perturbations associated with the water layer and Na+-STx-1 vibrational modes such as AlAlOH and AlMgOH were examined. Data indicate that CO 2 is preferentially incorporated into the interlayer space, with relatively dehydrated Na +-STx-1 capable of incorporating more CO 2 compared to hydrated Na +-STx-1. Spectroscopic data provide no evidence of formation of carbonate minerals or the interaction of CO 2 with sodium cations in the Na +-STx-1 structure.« less

Molecular induced skyhook effect for magnetic interlayer softening

NASA Astrophysics Data System (ADS)

Friedrich, Rico; Caciuc, Vasile; Atodiresei, Nicolae; Blügel, Stefan

2015-11-01

Our first-principles study demonstrates for the first time that by increasing the molecule-surface binding strength, the interlayer magnetic coupling of a ferromagnetic metal can be drastically reduced with respect to that of a clean substrate. Importantly, for a weakly chemisorbed molecule the rehybridization of metal atomic d states within the molecule-induced surface geometry (geometrical effect) plays a crucial role in obtaining interlayer magnetic softening. On the contrary, for a strongly chemisorbed molecule the interlayer magnetic coupling is further reduced due to an interplay between the geometrical effect and the hybridization of atomic d states with molecular ones.

Activity and Stability of (Pr 1-xNd x) 2NiO 4 as Cathodes for Solid Oxide Fuel Cells: Part V. In Situ Studies of Phase Evolution

DOE PAGES

Dogdibegovic, Emir; Alabri, Nawf S.; Wright, Christopher J.; ...

2017-08-12

This study is to complement an early report (the manuscript is attached for review purpose) on the role of interlayer on activity and performance stability in praseodymium nickelates. The aforementioned report showed a remarkable 48% increase in power density while switching from common GDC interlayer to a new interlayer chemistry (PGCO). Furthermore, a stable long-term performance was linked with suppressed reaction between the cathode and PGCO interlayer. In this article, we report in situ studies of the phase evolution. The high energy XRD studies at a synchrotron source showed fully suppressed phase transition in praseodymium nickelates with PGCO interlayer, whilemore » the electrodes on the GDC interlayer undergo substantial phase transformation. Furthermore, in operando and post-test XRD analyses shown fully suppressed structural changes in electrodes operated in full cells at 750°C and 0.80 V for 500 hours. SEM-EDS analysis showed that the formation of PrO x at the cathode-interlayer interface may play a role in a decrease of mechanical integrity of the interfaces, due to thermal expansion mismatch, leading to a local stress between the two phases. Furthermore, phase evolution at a narrow interface may propagate toward the electrode bulk, leading to structural changes Q1 and performance degradation.« less

Activity and Stability of (Pr 1-xNd x) 2NiO 4 as Cathodes for Solid Oxide Fuel Cells: Part V. In Situ Studies of Phase Evolution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dogdibegovic, Emir; Alabri, Nawf S.; Wright, Christopher J.

This study is to complement an early report (the manuscript is attached for review purpose) on the role of interlayer on activity and performance stability in praseodymium nickelates. The aforementioned report showed a remarkable 48% increase in power density while switching from common GDC interlayer to a new interlayer chemistry (PGCO). Furthermore, a stable long-term performance was linked with suppressed reaction between the cathode and PGCO interlayer. In this article, we report in situ studies of the phase evolution. The high energy XRD studies at a synchrotron source showed fully suppressed phase transition in praseodymium nickelates with PGCO interlayer, whilemore » the electrodes on the GDC interlayer undergo substantial phase transformation. Furthermore, in operando and post-test XRD analyses shown fully suppressed structural changes in electrodes operated in full cells at 750°C and 0.80 V for 500 hours. SEM-EDS analysis showed that the formation of PrO x at the cathode-interlayer interface may play a role in a decrease of mechanical integrity of the interfaces, due to thermal expansion mismatch, leading to a local stress between the two phases. Furthermore, phase evolution at a narrow interface may propagate toward the electrode bulk, leading to structural changes Q1 and performance degradation.« less

Carbon felt interlayer derived from rice paper and its synergistic encapsulation of polysulfides for lithium-sulfur batteries

NASA Astrophysics Data System (ADS)

Yang, Kai; Zhong, Lei; Guan, Ruiteng; Xiao, Min; Han, Dongmei; Wang, Shuanjin; Meng, Yuezhong

2018-05-01

Lithium-sulfur (Li-S) batteries have remarkably high theoretical specific capacity as promising candidates for next-generation energy storage. However, the "polysulfides shuttle" effect hampers its commercial application. Here, we use a kind of rice paper as a raw material to get inorganic oxides doping carbon felt by the facile carbonization method, and then modified by a simple coating process using poly (fluorenyl ether ketone) and Super P slurry. The special structure of the carbon felt derived from rice paper and its modified layer endow the final electronic conductive interlayer with inherent polysulfides absorbents and ion Coulombic repulsion functions, respectively, which show synergistic effect for trapping polysulfides. As an interlayer of Li-S batteries, the obtained carbon felt/poly (fluorenyl ether ketone)& Super P (CFSS) interlayer shows excellent electrochemical performance in improving specific capacity and decreasing polarization. The batteries with CFSS interlayer exhibit a high capacity of 837 mA h g-1 at 2.0 C and a high initial capacity of 1073.4 mA h g-1 and good capacity retention of 824.5 mA h g-1 after 500 cycles at 0.5 C. CFSS interlayer also shows excellent anti-self-discharge performance. Therefore, the simple and economical CFSS interlayer can be considered as a promising component for high performance Li-S batteries.

Effect of sulphur vacancy and interlayer interaction on the electronic structure and spin splitting of bilayer MoS2.

PubMed

Dong, Yulan; Zeng, Bowen; Xiao, Jin; Zhang, Xiaojiao; Li, Dongde; Li, Mingjun; He, Jun; Long, Mengqiu

2018-02-27

Molybdenum disulfide (MoS 2 ) is one of the candidate materials for nanoelectronics and optoelectronics devices in the future. The electronic and magnetic properties of MoS 2 can be regulated by interlayer interaction and the vacancy effect. Nevertheless, the combined effect of these two factors on MoS 2 is not clearly understood. In this study, we have investigated the impact of a single S vacancy combined with interlayer interaction on the properties of bilayer MoS 2 . Our calculated results show that an S vacancy brings impurity states in the band structure of bilayer MoS 2 , and the energy level of the impurity states can be affected by the interlayer distance, which finally disappears in the bulk state when the layer distance is relatively small. Moreover, during the compression of bilayer MoS 2 , the bottom layer, where the S vacancy stays, gets an additional charge due to interlayer charge transfer, which first increases, and then decreases due to gradually forming the interlayer S-S covalent bond, as interlayer distance decreases. The change of the additional charge is consistent with the change of the total magnetic moment of the bottom layers, no magnetic moment has been found in the top layer. The distribution of magnetic moment mainly concentrates on the three Mo atoms around the S vacancy, for each of which the magnetic moment is very much related to the Mo-Mo length. Our conclusion is that the interlayer charge transfer and S vacancy co-determine the magnetic properties of this system, which may be a useful way to regulate the electronic and magnetic properties of MoS 2 for potential applications.

Effect of sulphur vacancy and interlayer interaction on the electronic structure and spin splitting of bilayer MoS2

NASA Astrophysics Data System (ADS)

Dong, Yulan; Zeng, Bowen; Xiao, Jin; Zhang, Xiaojiao; Li, Dongde; Li, Mingjun; He, Jun; Long, Mengqiu

2018-03-01

Molybdenum disulfide (MoS2) is one of the candidate materials for nanoelectronics and optoelectronics devices in the future. The electronic and magnetic properties of MoS2 can be regulated by interlayer interaction and the vacancy effect. Nevertheless, the combined effect of these two factors on MoS2 is not clearly understood. In this study, we have investigated the impact of a single S vacancy combined with interlayer interaction on the properties of bilayer MoS2. Our calculated results show that an S vacancy brings impurity states in the band structure of bilayer MoS2, and the energy level of the impurity states can be affected by the interlayer distance, which finally disappears in the bulk state when the layer distance is relatively small. Moreover, during the compression of bilayer MoS2, the bottom layer, where the S vacancy stays, gets an additional charge due to interlayer charge transfer, which first increases, and then decreases due to gradually forming the interlayer S-S covalent bond, as interlayer distance decreases. The change of the additional charge is consistent with the change of the total magnetic moment of the bottom layers, no magnetic moment has been found in the top layer. The distribution of magnetic moment mainly concentrates on the three Mo atoms around the S vacancy, for each of which the magnetic moment is very much related to the Mo-Mo length. Our conclusion is that the interlayer charge transfer and S vacancy co-determine the magnetic properties of this system, which may be a useful way to regulate the electronic and magnetic properties of MoS2 for potential applications.

Observation of van Hove Singularities in Twisted Silicene Multilayers.

PubMed

Li, Zhi; Zhuang, Jincheng; Chen, Lan; Ni, Zhenyi; Liu, Chen; Wang, Li; Xu, Xun; Wang, Jiaou; Pi, Xiaodong; Wang, Xiaolin; Du, Yi; Wu, Kehui; Dou, Shi Xue

2016-08-24

Interlayer interactions perturb the electronic structure of two-dimensional materials and lead to new physical phenomena, such as van Hove singularities and Hofstadter's butterfly pattern. Silicene, the recently discovered two-dimensional form of silicon, is quite unique, in that silicon atoms adopt competing sp(2) and sp(3) hybridization states leading to a low-buckled structure promising relatively strong interlayer interaction. In multilayer silicene, the stacking order provides an important yet rarely explored degree of freedom for tuning its electronic structures through manipulating interlayer coupling. Here, we report the emergence of van Hove singularities in the multilayer silicene created by an interlayer rotation. We demonstrate that even a large-angle rotation (>20°) between stacked silicene layers can generate a Moiré pattern and van Hove singularities due to the strong interlayer coupling in multilayer silicene. Our study suggests an intriguing method for expanding the tunability of the electronic structure for electronic applications in this two-dimensional material.

Temperature dependence of interlayer coupling in perpendicular magnetic tunnel junctions with GdOx barriers

DOE PAGES

Newhouse-Illige, T.; Xu, Y. H.; Liu, Y. H.; ...

2018-02-13

Perpendicular magnetic tunnel junctions with GdO X tunneling barriers have shown a unique voltage controllable interlayer magnetic coupling effect. Here we investigate the quality of the GdO X barrier and the coupling mechanism in these junctions by examining the temperature dependence of the tunneling magnetoresistance and the interlayer coupling from room temperature down to 11 K. The barrier is shown to be of good quality with the spin independent conductance only contributing a small portion, 14%, to the total room temperature conductance, similar to AlO X and MgO barriers. The interlayer coupling, however, shows an anomalously strong temperature dependence includingmore » sign changes below 80 K. This non-trivial temperature dependence is not described by previous models of interlayer coupling and may be due to the large induced magnetic moment of the Gd ions in the barrier.« less

Magnetron sputtered zinc oxide nanorods as thickness-insensitive cathode interlayer for perovskite planar-heterojunction solar cells.

PubMed

Liang, Lusheng; Huang, Zhifeng; Cai, Longhua; Chen, Weizhong; Wang, Baozeng; Chen, Kaiwu; Bai, Hua; Tian, Qingyong; Fan, Bin

2014-12-10

Suitable electrode interfacial layers are essential to the high performance of perovskite planar heterojunction solar cells. In this letter, we report magnetron sputtered zinc oxide (ZnO) film as the cathode interlayer for methylammonium lead iodide (CH3NH3PbI3) perovskite solar cell. Scanning electron microscopy and X-ray diffraction analysis demonstrate that the sputtered ZnO films consist of c-axis aligned nanorods. The solar cells based on this ZnO cathode interlayer showed high short circuit current and power conversion efficiency. Besides, the performance of the device is insensitive to the thickness of ZnO cathode interlayer. Considering the high reliability and maturity of sputtering technique both in lab and industry, we believe that the sputtered ZnO films are promising cathode interlayers for perovskite solar cells, especially in large-scale production.

Temperature dependence of interlayer coupling in perpendicular magnetic tunnel junctions with GdOx barriers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newhouse-Illige, T.; Xu, Y. H.; Liu, Y. H.

Perpendicular magnetic tunnel junctions with GdO X tunneling barriers have shown a unique voltage controllable interlayer magnetic coupling effect. Here we investigate the quality of the GdO X barrier and the coupling mechanism in these junctions by examining the temperature dependence of the tunneling magnetoresistance and the interlayer coupling from room temperature down to 11 K. The barrier is shown to be of good quality with the spin independent conductance only contributing a small portion, 14%, to the total room temperature conductance, similar to AlO X and MgO barriers. The interlayer coupling, however, shows an anomalously strong temperature dependence includingmore » sign changes below 80 K. This non-trivial temperature dependence is not described by previous models of interlayer coupling and may be due to the large induced magnetic moment of the Gd ions in the barrier.« less

Electronic cooling via interlayer Coulomb coupling in multilayer epitaxial graphene

PubMed Central

Mihnev, Momchil T.; Tolsma, John R.; Divin, Charles J.; Sun, Dong; Asgari, Reza; Polini, Marco; Berger, Claire; de Heer, Walt A.; MacDonald, Allan H.; Norris, Theodore B.

2015-01-01

In van der Waals bonded or rotationally disordered multilayer stacks of two-dimensional (2D) materials, the electronic states remain tightly confined within individual 2D layers. As a result, electron–phonon interactions occur primarily within layers and interlayer electrical conductivities are low. In addition, strong covalent in-plane intralayer bonding combined with weak van der Waals interlayer bonding results in weak phonon-mediated thermal coupling between the layers. We demonstrate here, however, that Coulomb interactions between electrons in different layers of multilayer epitaxial graphene provide an important mechanism for interlayer thermal transport, even though all electronic states are strongly confined within individual 2D layers. This effect is manifested in the relaxation dynamics of hot carriers in ultrafast time-resolved terahertz spectroscopy. We develop a theory of interlayer Coulomb coupling containing no free parameters that accounts for the experimentally observed trends in hot-carrier dynamics as temperature and the number of layers is varied. PMID:26399955

Sandblasting induced stress release and enhanced adhesion strength of diamond films deposited on austenite stainless steel

NASA Astrophysics Data System (ADS)

Li, Xiao; Ye, Jiansong; Zhang, Hangcheng; Feng, Tao; Chen, Jianqing; Hu, Xiaojun

2017-08-01

We firstly used sandblasting to treat austenite stainless steel and then deposited a Cr/CrN interlayer by close field unbalanced magnetron sputtering on it. After that, diamond films were prepared on the interlayer. It is found that the sandblasting process induces phase transition from austenite to martensite in the surface region of the stainless steel, which decreases thermal stress in diamond films due to lower thermal expansion coefficient of martensite phase compared with that of austenite phase. The sandblasting also makes stainless steel's surface rough and the Cr/CrN interlayer film inherits the rough surface. This decreases the carburization extent of the interlayer, increases nucleation density and modifies the stress distribution. Due to lower residual stress and small extent of the interlayer's carburization, the diamond film on sandblast treated austenite stainless steel shows enhanced adhesion strength.

The coherent interlayer resistance of a single, rotated interface between two stacks of AB graphite

NASA Astrophysics Data System (ADS)

Habib, K. M. Masum; Sylvia, Somaia S.; Ge, Supeng; Neupane, Mahesh; Lake, Roger K.

2013-12-01

The coherent, interlayer resistance of a misoriented, rotated interface between two stacks of AB graphite is determined for a variety of misorientation angles. The quantum-resistance of the ideal AB stack is on the order of 1 to 10 mΩ μm2. For small rotation angles, the coherent interlayer resistance exponentially approaches the ideal quantum resistance at energies away from the charge neutrality point. Over a range of intermediate angles, the resistance increases exponentially with cell size for minimum size unit cells. Larger cell sizes, of similar angles, may not follow this trend. The energy dependence of the interlayer transmission is described.

Inter-layer potential for hexagonal boron nitride

NASA Astrophysics Data System (ADS)

Leven, Itai; Azuri, Ido; Kronik, Leeor; Hod, Oded

2014-03-01

A new interlayer force-field for layered hexagonal boron nitride (h-BN) based structures is presented. The force-field contains three terms representing the interlayer attraction due to dispersive interactions, repulsion due to anisotropic overlaps of electron clouds, and monopolar electrostatic interactions. With appropriate parameterization, the potential is able to simultaneously capture well the binding and lateral sliding energies of planar h-BN based dimer systems as well as the interlayer telescoping and rotation of double walled boron-nitride nanotubes of different crystallographic orientations. The new potential thus allows for the accurate and efficient modeling and simulation of large-scale h-BN based layered structures.

Plasticized Polymer Interlayer for Low-Temperature Fabrication of a High-Quality Silver Nanowire-Based Flexible Transparent and Conductive Film

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jo, Wonhee; Kang, Hong Suk; Choi, Jaeho

Silver nanowires (AgNWs) are one of the most promising materials to replace commercially available indium tin oxide in flexible transparent conductive films (TCFs); however, there are still numerous problems originating from poor AgNW junction formation and improper AgNW embedment into transparent substrates. To mitigate these problems, high-temperature processes have been adopted; however, unwanted substrate deformation prevents the use of these processes for the formation of flexible TCFs. In this work, we present a novel poly(methyl methacrylate) interlayer plasticized by dibutyl phthalate for low-temperature fabrication of AgNW-based TCFs, which does not cause any substrate deformation. By exploiting the viscoelastic properties ofmore » the plasticized interlayer near the lowered glass-transition temperature, a monolithic junction of AgNWs on the interlayer and embedment of the interconnected AgNWs into the interlayer are achieved in a single-step pressing. The resulting AgNW-TCFs are highly transparent (~92% at a wavelength of 550 nm), highly conductive (<90 Ω/sq), and environmentally and mechanically robust. Therefore, the plasticized interlayer provides a simple and effective route to fabricate high-quality AgNW-based TCFs.« less

Dynamics of water in synthetic saponite clays: Effect of trivalent ion substitution

NASA Astrophysics Data System (ADS)

Mitra, S.; Prabhudesai, S. A.; Chakrabarty, D.; Sharma, V. K.; Vicente, M. A.; Embs, J. P.; Mukhopadhyay, R.

2013-06-01

Saponite clay belongs to the phyllosilicate family and is comprised of layers of Si(IV) tetrahedra and Al(III) or Mg(II) octahedra with definite interlayer spacing. In these systems, the trivalent ion substitutions in the tetrahedral layers lead to negative charge on the layers. Here we report the dynamics of water contained in [Si6.97Al1.03][Ni6.00]O20(OH)4[Na1.03]·28H2O (SAP-1) and [Si7.13Fe0.86][Ni6.00]O20(OH)4[Na0.86]·14H2O (SAP-2) saponite clays in the temperature range 200-310 K as studied by quasielastic neutron scattering technique. Particularly the effect of the ion substitution towards the dynamics of water is addressed here. Data analysis is carried out using the relaxing cage model. The existence of distribution in relaxation times indicated that the water molecules in saponite clay have a different local environment which leads to complex diffusion behavior. It is found that water exists in a supercooled state in the temperature range up to 235 K. However, some of the water molecules are found to be immobile in the temperature range 240-285 K. The fraction of immobile water decreases with increase in temperature. At higher temperatures, some of the water molecules in the hydration shells or those near the surface start participating in the diffusion process and at 293 K, almost all water molecules contribute to the dynamics. Diffusivity of water in both SAP-1 and SAP-2 are found to be lower in comparison to the bulk, and within the two samples of saponite clay diffusivity in SAP-1 is found to be lower compared to SAP-2; this has been explained on the basis of the charge on the tetrahedral layers and the charge balancing cations in the interlayer spacing.

Assessing Hydration in Children: From Science to Practice.

PubMed

Guelinckx, I; Frémont-Marquis, A S; Eon, E; Kavouras, S A; Armstrong, L E

2015-01-01

Raising children's awareness about their hydration status could be done through a noninvasive biomarker. Urine color (UC) has been validated as a biomarker of hydration in adults and children aged 8-14 years. The aim of this survey was to design and to evaluate the level of understanding and attractiveness of a self-assessment, UC-based hydration tool for children aged 6-11 years. The first phase of the survey consisted of face-to-face interviews during which 84 children identified those graphical elements necessary to understand the hydration message from 6 illustration-based designs containing the UC chart. The graphic elements selected were the basis to create 3 new designs. During the 2nd phase, the level of understanding and attractiveness of these 3 new designs was then evaluated via an online questionnaire by a total of 1,231 children in 3 countries. The design with the highest level of understanding was totally or partially understood by 76% of the participants, independent of age and gender. The levels of understanding, however, differed in the countries. In Indonesia, the levels of understanding of the 3 designs were comparable; whereas in both France (74%) and Mexico (78%), significantly more participants totally and partially understood one of the 3 designs. The levels of attractiveness of the 3 designs were comparable, independent of country, age, and gender. On average, 80% of all participants liked the 3 designs a bit or a lot. Only 14% did not like the designs, and 5% of participants had no opinion regarding attractiveness. These results indicated that three out of four children like and understand the correct hydration message from a strictly illustration-based tool containing the eight-point UC scale. © 2015 S. Karger AG, Basel.

Detecting a proper patient with a help of medical data retrieval

NASA Astrophysics Data System (ADS)

Malecka-Massalska, Teresa; Maciejewski, Ryszard; Wasiewicz, Piotr; Zaluska, Wojciech; Ksiazek, Andrzej

2009-06-01

Electric bioimpedance is one of methods to assess the hydrate status in hemodialyzed patients. It is also being used for assessing the hydration level among peritoneal dialysed patients, diagnosed with neoplastic diseases, patients after organ transplantations and the ones infected with HIV virus. During measurements sets were obtained from two groups, which were named a control (healthy volunteers) and test group (hemodialyzed patients). Zscored, discretized data and data retrieval results were computed in R language environment in order to find a simple rule for recognizing health problems. The executed experiments affirm possibilities of creating good classifiers for detecting a proper patient with the help of medical data sets, but only with previous training.

[Hydration in clinical practice].

PubMed

Maristany, Cleofé Pérez-Portabella; Segurola Gurruchaga, Hegoi

2011-01-01

Water is an essential foundation for life, having both a regulatory and structural function. The former results from active and passive participation in all metabolic reactions, and its role in conserving and maintaining body temperature. Structurally speaking it is the major contributer to tissue mass, accounting for 60% of the basis of blood plasma, intracellular and intersticial fluid. Water is also part of the primary structures of life such as genetic material or proteins. Therefore, it is necessary that the nurse makes an early assessment of patients water needs to detect if there are signs of electrolyte imbalance. Dehydration can be a very serious problem, especially in children and the elderly. Dehydrations treatment with oral rehydration solution decreases the risk of developing hydration disorders, but even so, it is recommended to follow preventive measures to reduce the incidence and severity of dehydration. The key to having a proper hydration is prevention. Artificial nutrition encompasses the need for precise calculation of water needs in enteral nutrition as parenteral, so the nurse should be part of this process and use the tools for calculating the patient's requirements. All this helps to ensure an optimal nutritional status in patients at risk. Ethical dilemmas are becoming increasingly common in clinical practice. On the subject of artificial nutrition and hydration, there isn't yet any unanimous agreement regarding hydration as a basic care. It is necessary to take decisions in consensus with the health team, always thinking of the best interests of the patient.

Are we being drowned by overhydration advice on the Internet?

PubMed

Hoffman, Martin D; Bross, Theodore L; Hamilton, R Tyler

2016-11-01

Because inappropriate recommendations about hydration during exercise appear widespread and potentially dangerous, we assessed the quality of a sampling of information currently available to the public on the Internet. Internet searches using the Google search engine were conducted using the terms "hydration," "hydration guidelines," "drinking fluids" and "drinking guidelines" combined with "and exercise." From the first 50 websites for each search phrase, duplicates were removed yielding 141 unique websites that were categorized by source and examined for specific hydration related information and recommendations. Correct endorsement was as follows (reported as percent endorsing the concept relative to the number of websites addressing the issue): some weight loss should be expected during exercise (69.5% of 95), fluid consumption during exercise should be based upon thirst (7.3% of 110), electrolyte intake is not generally necessary during exercise (10.4% of 106), dehydration is not generally a cause of heat illness (3.4% of 58) or exercise-associated muscle cramping (2.4% of 42), exercise-associated muscle cramping is not generally related to electrolyte loss (0.0% of 16), and overhydration is a risk for hyponatremia (100.0% of 61). Comparison of website information from medical or scientific sources with that from other sources revealed no differences (p = 0.4 to 1.0) in the frequency of correct endorsement of the examined criteria. Prevalent misinformation on the Internet about hydration needs during exercise and the contribution of hydration status to the development of heat illness and muscle cramping fosters overhydration. In general, those websites that should be most trusted by the public were no better than other websites at providing accurate information, and the potential risk of hyponatremia from overhydration was noted by less than half the websites. Since deaths from exercise-associated hyponatremia should be preventable through avoidance of overhydration, dissemination of a more appropriate hydration message is important.

Transient liquid phase bonding of titanium-, iron- and nickel-based alloys

NASA Astrophysics Data System (ADS)

Rahman, A. H. M. Esfakur

The operating temperature of land-based gas turbines and jet engines are ever-increasing to increase the efficiency, decrease the emissions and minimize the cost. Within the engines, complex-shaped parts experience extreme temperature, fatigue and corrosion conditions. Ti-based, Ni-based and Fe-based alloys are commonly used in gas turbines and jet engines depending on the temperatures of different sections. Although those alloys have superior mechanical, high temperature and corrosion properties, severe operating conditions cause fast degradation and failure of the components. Repair of these components could reduce lifecycle costs. Unfortunately, conventional fusion welding is not very attractive, because Ti reacts very easily with oxygen and nitrogen at high temperatures, Ni-based superalloys show heat affected zone (HAZ) cracking, and stainless steels show intergranular corrosion and knife-line attack. On the other hand, transient liquid phase (TLP) bonding method has been considered as preferred joining method for those types of alloys. During the initial phase of the current work commercially pure Ti, Fe and Ni were diffusion bonded using commercially available interlayer materials. Commercially pure Ti (Ti-grade 2) has been diffusion bonded using silver and copper interlayers and without any interlayer. With a silver (Ag) interlayer, different intermetallics (AgTi, AgTi2) appeared in the joint centerline microstructure. While with a Cu interlayer eutectic mixtures and Ti-Cu solid solutions appeared in the joint centerline. The maximum tensile strengths achieved were 160 MPa, 502 MPa, and 382 MPa when Ag, Cu and no interlayers were used, respectively. Commercially pure Fe (cp-Fe) was diffusion bonded using Cu (25 m) and Au-12Ge eutectic interlayer (100 microm). Cu diffused predominantly along austenite grain boundaries in all bonding conditions. Residual interlayers appeared at lower bonding temperature and time, however, voids were observed in the joint centerline at higher joining temperature and time. Dispersed Au-rich particles were observed in the base metal near interface. The highest ultimate tensile strengths obtained for the bonded Fe were 291+/-2 MPa using a Cu interlayer at 1030°C for 10 h and 315+/-4 MPa using a Au-12Ge interlayer at 950°C for 15 h. Commercially pure Ni (cp-Ni) was diffusion bonded using a Al, Au-12Ge or Cu interlayer. The formation of intermetallics could not be avoided when Al interlayer was used. Even though no intermetallics were obtained with Au-12Ge or Cu interlayer, appreciable strength of the joint was not found. Next, the simple bonding systems were modeled numerically. It is hoped that the simple models can be extended for higher order alloys. The modeling of TLP joint means to come up with a mathematical model which can predict the concentration profiles of diffusing species. The concentration dependence of diffusivity in a multi-component diffusion system makes it complicated to predict the concentration profiles of diffusing species. The so-called chemical diffusivity can be expressed as a function of thermodynamic and kinetic data. DICTRA software can calculate the concentration profiles using appropriate mobility and thermodynamic data. It can also optimize the diffusivity data using experimental diffusivity data. Then the optimized diffusivity data is stored as mobility data which is a linear function of temperature. In this work, diffusion bonding of commercially pure Ni using Cu interlayers is reported. The mobility parameters of Ni-Cu alloy binary systems were optimized using DICTRA/Thermocalc software from the available self-, tracer and chemical diffusion coefficients. The optimized mobility parameters were used to simulate concentration profiles of Ni-Cu diffusion joints using DICTRA/Thermocalc software. The calculated and experimental concentration profiles agreed well at 1100 °C. This method could not be extended for higher order alloys because of the lack of appropriate thermodynamic and kinetic database. In the third phase industrially important alloys such as SS 321, Inconel 718 and Ti-6Al-4V were diffusion bonded. Diffusion bonded SS 321 with Au-12Ge interlayer provided the best microstructure when bonded in either vacuum or argon at 1050°C for 20 h and cooled in air. The maximum strength obtained of the joint was 387+/-4 MPa bonded in vacuum at 1050°C for 20 h and cooled in air. The microstructure of joint centerline of diffusion bonded Inconel 718 using Au-12Ge interlayer at 1050°C for 15 h and cooled in air consisted of residual interlayer (1.3-2.5 microm). The residual interlayer was disappeared by increasing the bonding time by 5 h, however, pores appeared in the joint centerline. As a result, the strength obtained for bonded Inconel 718 was much lower than that of the base alloy. The joint centerline microstructure of bonded Ti-6Al-4V using Cu interlayer was free of intermetallics and solid solution of Cu and base alloy. The strength of the joint is yet to be determined.

Asphalt-Rubber SAMI (Stress-Absorbing Membrane Interlayers) Field Evaluation.

DTIC Science & Technology

1986-04-01

revealed that there was promise in using the material as an interlayer to prevent the reflection of cracks from an old pavement to a new asphalt -concrete...reflection cracking , and (2) that asphalt - rubber interlayers should be investigated in conjunction with conventional asphalt -concrete overlays. An... Asphalt -rubber samples were taken and tested and construction activities were documented. The performance has been monitored by conducting crack

REVIEWS OF TOPICAL PROBLEMS: Neutrinos from stellar core collapses: present status of experiments

NASA Astrophysics Data System (ADS)

Ryazhskaya, Ol'ga G.

2006-10-01

The responses of the existing underground detectors to neutrino bursts from collapsing stars evolving in accordance with various models are considered. The interpretation of the results of detecting neutrino radiation from the SN1987A supernova explosion is discussed. A combination of large scintillation counters interlayered with iron slabs (as a target for the electron neutrino interaction) is suggested as a detector for core collapse neutrinos. Bounds for the galactic rate of core collapses based on 28 years of observations by neutrino telescopes of RAS INR, LSD, and LVD detectors are presented.

Origins of interlayer formation and misfit dislocation displacement in the vicinity of InAs/GaAs quantum dots

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, S.; Kim, S. J.; Pan, X. Q.

We have examined the origins of interlayer formation and misfit dislocation (MD) displacement in the vicinity of InAs/GaAs quantum dots (QDs). For QDs formed by the Stranski-Krastanov mode, regularly spaced MDs nucleate at the interface between the QD and the GaAs buffer layer. In the droplet epitaxy case, both In island formation and In-induced “nano-drilling” of the GaAs buffer layer are observed during In deposition. Upon annealing under As flux, the In islands are converted to InAs QDs, with an InGaAs interlayer at the QD/buffer interface. Meanwhile, MDs nucleate at the QD/interlayer interface.

Observation of interlayer excitons in MoSe2 single crystals

NASA Astrophysics Data System (ADS)

Horng, Jason; Stroucken, Tineke; Zhang, Long; Paik, Eunice Y.; Deng, Hui; Koch, Stephan W.

2018-06-01

Interlayer excitons with direct optical transitions are observed coexisting with intralayer excitons in the same K valleys in bilayer, few-layer, and bulk MoSe2 single crystals by confocal reflection contrast spectroscopy. Quantitative analysis using the Dirac-Bloch equations provides unambiguous state assignment of all the measured resonances. The interlayer excitons in bilayer MoSe2 have a large binding energy of 153 meV and a narrow linewidth of 20 meV. Their spectral weight is comparable to the commonly studied higher-order intralayer excitons. At the same time, the interlayer excitons are characterized by distinct transition energies and permanent dipole moments, providing a promising high temperature and optically accessible platform for dipolar exciton physics.

Multilayer Disk Reduced Interlayer Crosstalk with Wide Disk-Fabrication Margin

NASA Astrophysics Data System (ADS)

Hirotsune, Akemi; Miyauchi, Yasushi; Endo, Nobumasa; Onuma, Tsuyoshi; Anzai, Yumiko; Kurokawa, Takahiro; Ushiyama, Junko; Shintani, Toshimichi; Sugiyama, Toshinori; Miyamoto, Harukazu

2008-07-01

To reduce interlayer crosstalk caused by the ghost spot which appears in a multilayer optical disk with more than three information layers, a multilayer disk structure which reduces interlayer crosstalk with a wide disk-fabrication margin was proposed in which the backward reflectivity of the information layers is sufficiently low. It was confirmed that the interlayer crosstalk caused by the ghost spot was reduced to less than the crosstalk from the adjacent layer by controlling backward reflectivity. The wide disk-fabrication margin of the proposed disk structure was indicated by experimentally confirming that the tolerance of the maximum deviation of the spacer-layer thickness is four times larger than that in the previous multilayer disk.

Influence of a MoOx interlayer on the open-circuit voltage in organic photovoltaic cells

NASA Astrophysics Data System (ADS)

Zou, Yunlong; Holmes, Russell J.

2013-07-01

Metal-oxides have been used as interlayers at the anode-organic interface in organic photovoltaic cells (OPVs) to increase the open-circuit voltage (VOC). We examine the role of MoOx in determining the maximum VOC in a planar heterojunction OPV and find that the interlayer strongly affects the temperature dependence of VOC. Boron subphthalocyanine chloride (SubPc)-C60 OPVs that contain no interlayer show a maximum VOC of 1.2 V at low temperature, while those with MoOx show no saturation, reaching VOC > 1.4 V. We propose that the MoOx-SubPc interface forms a Schottky junction that provides an additional contribution to VOC at low temperature.

Observation of van Hove Singularities in Twisted Silicene Multilayers

PubMed Central

2016-01-01

Interlayer interactions perturb the electronic structure of two-dimensional materials and lead to new physical phenomena, such as van Hove singularities and Hofstadter’s butterfly pattern. Silicene, the recently discovered two-dimensional form of silicon, is quite unique, in that silicon atoms adopt competing sp2 and sp3 hybridization states leading to a low-buckled structure promising relatively strong interlayer interaction. In multilayer silicene, the stacking order provides an important yet rarely explored degree of freedom for tuning its electronic structures through manipulating interlayer coupling. Here, we report the emergence of van Hove singularities in the multilayer silicene created by an interlayer rotation. We demonstrate that even a large-angle rotation (>20°) between stacked silicene layers can generate a Moiré pattern and van Hove singularities due to the strong interlayer coupling in multilayer silicene. Our study suggests an intriguing method for expanding the tunability of the electronic structure for electronic applications in this two-dimensional material. PMID:27610412

Antiferromagnetic Interlayer Exchange Coupling in All-Semiconducting EuS/PbS/EuS Trilayers

NASA Technical Reports Server (NTRS)

Smits, C. J. P.; Filip, A. T.; Swagten, H. J. M.; Koopmans, B.; deJonge, W. J. M.; Chernyshova, M.; Kowalczyk, L.; Grasza, K.; Szczerbakow, A.; Story, T.

2003-01-01

A comprehensive experimental study on the antiferromagnetic interlayer exchange coupling in high quality epitaxial all-semiconducting EuSPbSEuS trilayers is reported. The influence of substrates, the thickness of the non-magnetic PbS spacer layer, and of temperature, was investigated by means of SQUID magnetometry. In trilayers with a PbS thickness between 4 and 12 deg A the low temperature hysteresis loops showed the signature of antiferromagnetic coupling. The value of the interlayer exchange coupling energy was determined by simulating the data with a modified Stoner model, including Zeeman, anisotropy, and exchange coupling energies. An important observation was of a strong dependence of the interlayer exchange coupling energy on temperature, consistent with a power law dependence of the exchange coupling constant on the saturation magnetization of the EuS layers. While no theoretical description is readily available, we conjecture that the observed behavior is due to a dependence of the interlayer exchange coupling energy on the exchange splitting of the EuS conduction band.

Electrochemical preparation of carbon films with a Mo2C interlayer in LiCl-NaCl-Na2CO3 melts

NASA Astrophysics Data System (ADS)

Ge, Jianbang; Wang, Shuai; Zhang, Feng; Zhang, Long; Jiao, Handong; Zhu, Hongmin; Jiao, Shuqiang

2015-08-01

The electrodeposition of carbon films with a Mo2C interlayer was investigated in LiCl-NaCl-Na2CO3 melts at 900 °C. Cyclic voltammetry was applied to study the electrochemical reaction mechanism on Mo and Pt electrodes, indicating that, two reduction reactions including carbon deposition and carbon monoxide evolution, may take place on the two electrodes simultaneously during the cathodic sweep. Carbon films with a continuous Mo2C interlayer were prepared by constant voltage electrolysis, showing a good adhesion between Mo substrate and carbon films. The carbon films with a Mo2C interlayer were characterized using X-ray diffraction measurement, Raman spectroscopy, scanning electron microscopy and transmission electron microscopy. The results reveal that carbon materials deposited on the electrodes are mainly composed of graphite and carbon diffusion in Mo (or Mo2C) leads to the formation and growth of Mo2C interlayer.

Toward Increasing Micropore Volume between Hybrid Layered Perovskites with Silsesquioxane Interlayers.

PubMed

Kataoka, Sho; Kamimura, Yoshihiro; Endo, Akira

2018-04-10

Hybrid organic-inorganic layered perovskites are typically nonporous solids. However, the incorporation of silsesquioxanes with a cubic cage structure as interlayer materials creates micropores between the perovskite layers. In this study, we increase in the micropore volume in layered perovskites by replacing a portion of the silsesquioxane interlayers with organic amines. In the proposed method, approximately 20% of the silsesquioxane interlayers can be replaced without changing the layer distance owing to the size of the silsesquioxane. When small amines (e.g., ethylamine) are used in this manner, the micropore volume of the obtained hybrid layered perovskites increases by as much as 44%; when large amines (e.g., phenethylamine) are used, their micropore volume decreases by as much as 43%. Through the variation of amine fraction, the micropore volume can be adjusted in the range. Finally, the magnetic moment measurements reveal that the layered perovskites with mixed interlayers exhibit ferromagnetic ordering at temperature below 20 K, thus indicating that the obtained perovskites maintain their functions as layered perovskites.

Effects of GaN interlayer on the transport properties of lattice-matched AlInN/AlN/GaN heterostructures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, F.; Gao, K. H., E-mail: khgao@tju.edu.cn; Li, Z. Q.

2015-04-21

We study the effects of GaN interlayer on the transport properties of two-dimensional electron gases confined in lattice-matched AlInN/AlN/GaN heterostructures. It is found that the Hall mobility is evidently enhanced when an additional ultrathin GaN interlayer is introduced between AlInN and AlN layers. The enhancement of the Hall mobility is especially remarkable at low temperature. The high Hall mobility results in a low sheet resistance of 23 Ω/◻ at 2 K. Meanwhile, Shubnikov-de Haas oscillations (SdH) are also remarkably enhanced due to the existence of GaN interlayer. The enhancement of the SdH oscillations is related to the larger quantum mobility μ{sub q}more » owing to the suppression of the interface roughness, alloy disorder, and ionized impurity scatterings by the GaN interlayer.« less

Observation of long-lived interlayer excitons in monolayer MoSe 2–WSe 2 heterostructures

DOE PAGES

Rivera, Pasqual; Schaibley, John R.; Jones, Aaron M.; ...

2015-02-24

Van der Waals bound heterostructures constructed with two-dimensional materials, such as graphene, boron nitride and transition metal dichalcogenides, have sparked wide interest in both device physics and technologies at the two-dimensional limit. One highly coveted heterostructure is that of differing monolayer transition metal dichalcogenides with type-II band alignment, with bound electrons and holes localized in individual monolayers, that is, interlayer excitons. Here, we report the observation of interlayer excitons in monolayer MoSe 2–WSe 2 heterostructures by photoluminescence and photoluminescence excitation spectroscopy. The energy and luminescence intensity are highly tunable by an applied vertical gate voltage. Moreover, we measure an interlayermore » exciton lifetime of ~1.8 ns, an order of magnitude longer than intralayer excitons in monolayers. Ultimately, our work demonstrates optical pumping of interlayer electric polarization, which may provoke further exploration of interlayer exciton condensation, as well as new applications in two-dimensional lasers, light-emitting diodes and photovoltaic devices.« less

Interlayer electron-phonon coupling in WSe2/hBN heterostructures

NASA Astrophysics Data System (ADS)

Jin, Chenhao; Kim, Jonghwan; Suh, Joonki; Shi, Zhiwen; Chen, Bin; Fan, Xi; Kam, Matthew; Watanabe, Kenji; Taniguchi, Takashi; Tongay, Sefaattin; Zettl, Alex; Wu, Junqiao; Wang, Feng

2017-02-01

Engineering layer-layer interactions provides a powerful way to realize novel and designable quantum phenomena in van der Waals heterostructures. Interlayer electron-electron interactions, for example, have enabled fascinating physics that is difficult to achieve in a single material, such as the Hofstadter's butterfly in graphene/boron nitride (hBN) heterostructures. In addition to electron-electron interactions, interlayer electron-phonon interactions allow for further control of the physical properties of van der Waals heterostructures. Here we report an interlayer electron-phonon interaction in WSe2/hBN heterostructures, where optically silent hBN phonons emerge in Raman spectra with strong intensities through resonant coupling to WSe2 electronic transitions. Excitation spectroscopy reveals the double-resonance nature of such enhancement, and identifies the two resonant states to be the A exciton transition of monolayer WSe2 and a new hybrid state present only in WSe2/hBN heterostructures. The observation of an interlayer electron-phonon interaction could open up new ways to engineer electrons and phonons for device applications.

Photocarrier generation from interlayer charge-transfer transitions in WS2-graphene heterostructures

PubMed Central

Yuan, Long; Chung, Ting-Fung; Kuc, Agnieszka; Wan, Yan; Xu, Yang; Chen, Yong P.; Heine, Thomas; Huang, Libai

2018-01-01

Efficient interfacial carrier generation in van der Waals heterostructures is critical for their electronic and optoelectronic applications. We demonstrate broadband photocarrier generation in WS2-graphene heterostructures by imaging interlayer coupling–dependent charge generation using ultrafast transient absorption microscopy. Interlayer charge-transfer (CT) transitions and hot carrier injection from graphene allow carrier generation by excitation as low as 0.8 eV below the WS2 bandgap. The experimentally determined interlayer CT transition energies are consistent with those predicted from the first-principles band structure calculation. CT interactions also lead to additional carrier generation in the visible spectral range in the heterostructures compared to that in the single-layer WS2 alone. The lifetime of the charge-separated states is measured to be ~1 ps. These results suggest that interlayer interactions make graphene–two-dimensional semiconductor heterostructures very attractive for photovoltaic and photodetector applications because of the combined benefits of high carrier mobility and enhanced broadband photocarrier generation. PMID:29423439

Decrease in fruit moisture content heralds and might launch the onset of ripening processes.

PubMed

Frenkel, Chaim; Hartman, Thomas G

2012-10-01

It is known that fruit ripening is a genetically programmed event but it is not entirely clear what metabolic cue(s) stimulate the onset of ripening, ethylene action notwithstanding. Here, we examined the conjecture that fruit ripening might be evoked by an autonomously induced decrease in tissue water status. We found decline in water content occurring at the onset of ripening in climacteric and nonclimacteric fruit, suggesting that this phenomenon might be universal. This decline in water content persisted throughout the ripening process in some fruit, whereas in others it reversed during the progression of the ripening process. Applied ethylene also induced a decrease in water content in potato (Solanum tuberosum) tubers. In ethylene-mutant tomato (Solanum lycopersicum) fruit (antisense to1-aminocyclopropane carboxylate synthase), cold-induced decline in water content stimulated onset of ripening processes apparently independently of ethylene action, suggesting cause-and-effect relationship between decreasing water content and onset of ripening. The decline in tissue water content, occurring naturally or induced by ethylene, was strongly correlated with a decrease in hydration (swelling) efficacy of cell wall preparations suggesting that hydration dynamics of cell walls might account for changes in tissue moisture content. Extent of cell wall swelling was, in turn, related to the degree of oxidative cross-linking of wall-bound phenolic acids, suggesting that oxidant-induced wall restructuring might mediate cell wall and, thus, fruit tissue hydration status. We propose that oxidant-induced cell wall remodeling and consequent wall dehydration might evoke stress signaling for the onset of ripening processes. This study suggests that decline in fruit water content is an early event in fruit ripening. This information may be used to gauge fruit maturity for appropriate harvest date and for processing. Control of fruit hydration state might be used to regulate the onset of fruit ripening. © 2012 Institute of Food Technologists®

Inter-layer synchronization in non-identical multi-layer networks

NASA Astrophysics Data System (ADS)

Leyva, I.; Sevilla-Escoboza, R.; Sendiña-Nadal, I.; Gutiérrez, R.; Buldú, J. M.; Boccaletti, S.

2017-04-01

Inter-layer synchronization is a dynamical process occurring in multi-layer networks composed of identical nodes. This process emerges when all layers are synchronized, while nodes in each layer do not necessarily evolve in unison. So far, the study of such inter-layer synchronization has been restricted to the case in which all layers have an identical connectivity structure. When layers are not identical, the inter-layer synchronous state is no longer a stable solution of the system. Nevertheless, when layers differ in just a few links, an approximate treatment is still feasible, and allows one to gather information on whether and how the system may wander around an inter-layer synchronous configuration. We report the details of an approximate analytical treatment for a two-layer multiplex, which results in the introduction of an extra inertial term accounting for structural differences. Numerical validation of the predictions highlights the usefulness of our approach, especially for small or moderate topological differences in the intra-layer coupling. Moreover, we identify a non-trivial relationship connecting the betweenness centrality of the missing links and the intra-layer coupling strength. Finally, by the use of multiplexed layers of electronic circuits, we study the inter-layer synchronization as a function of the removed links.

Mechanism of mechanically induced optoelectronic and spintronic phase transitions in 1D graphene spirals: insight into the role of interlayer coupling.

PubMed

Xu, Xiaodong; Liu, Bingyi; Zhao, Wenyu; Jiang, Yongyuan; Liu, Linhua; Li, Weiqi; Zhang, Guiling; Tian, Wei Quan

2017-07-13

Graphene spirals (GSs), an emerging carbonic nano-material with a Riemann surface, demonstrate extraordinary topological electronic signatures: interlayer coupling similar to van der Waals (vdW) heterojunctions and intralayer coupling within the spiral conformation. Based on the state-of-the-art first-principles technique, the electronic properties of the periphery-modified GSs with geometry deformation are explored under axial strain. For all GSs, there emerges a remarkable phase transition from metal to semiconductor, due to the attenuation of interlayer "σ-bonds" reducing the interlayer tunneling probability for carriers. Analogous to graphene, GSs consist of bipartite sublattices with carbonic sp 2 hybridization as well. Once the balance of the bipartite sublattices is lost, there will emerge intense edge (corner) states, contributed by the p z orbitals. In contrast to isolated graphene nanoflakes, GSs realize the continuous spin-polarized edge (corner) state coupling with 1D morphology. However, the spin-polarization is blocked by the robust interlayer "σ-bonds" so that the spintronic transition takes place until this interlayer coupling is broken. More intriguingly, an indirect-direct bandgap transition is observed, revealing excellent optical on-off features. Their tunable properties provide great potential for their application in optoelectronics, spintronics and chemical or biological sensors.

Development of a Novel Ni-Fe-Cr-B-Si Interlayer Material for Transient Liquid Phase Bonding of Inconel 718

NASA Astrophysics Data System (ADS)

Tarai, U. K.; Robi, P. S.; Pal, Sukhomay

2018-04-01

A Ni-Cr-Fe-Si-B based interlayer material was developed by mechanical alloying (MA) process in a high-energy planetary ball mill. Equiaxed alloy powders of size 12 µm was obtained after milling for 50 hours. X-ray diffraction analysis of the milled powder revealed that milling of elemental powders initially resulted in microcrystalline alloy powder having face centered cubic structure, which on subsequent milling resulted in nano-crystallice alloy powder with a crystallite size of 3.2 nm. XRD analysis also reveals formation of metastable eutectic alloys resulting in lowering of the melting point of the interlayer material to 1025 °C. IN 718 superalloy samples were joined at 1050°C using the developed interlayer. A homogeneous joint was formed by the newly developed interlayer material. Three different zones were observed at the bond (i) isothermally solidified zone, (ii) diffusion affected zone and (iii) unaffected base metal. In the diffusion-affected zone, boron was present at the grain boundaries of Ni γ matrix in bulky metal borides form. The diffusion of boron from interlayer material into the base material was mechanism of isothermal solidification and bond formation in transient liquid phase bonding of IN 718.

Revealing the preferred interlayer orientations and stackings of two-dimensional bilayer gallium selenide crystals

DOE PAGES

Li, Xufan; Basile Carrasco, Leonardo A.; Yoon, Mina; ...

2015-01-21

Characterizing and controlling the interlayer orientations and stacking order of bilayer two-dimensional (2D) crystals and van der Waals (vdW) heterostructure is crucial to optimize their electrical and optoelectronic properties. The four polymorphs of layered gallium selenide (GaSe) that result from different layer stacking provide an ideal platform to study the stacking configurations in bilayer 2D crystals. Here, through a controllable vapor-phase deposition method we selectively grow bilayer GaSe crystals and investigate their two preferred 0° or 60° interlayer rotations. The commensurate stacking configurations (AA' and AB-stacking) in as-grown 2D bilayer GaSe crystals are clearly observed at the atomic scale andmore » the Ga-terminated edge structure are identified for the first time by using atomic-resolution scanning transmission electron microscopy (STEM). Theoretical analysis of the interlayer coupling energetics vs. interlayer rotation angle reveals that the experimentally-observed orientations are energetically preferred among the bilayer GaSe crystal polytypes. Here, the combined experimental and theoretical characterization of the GaSe bilayers afforded by these growth studies provide a pathway to reveal the atomistic relationships in interlayer orientations responsible for the electronic and optical properties of bilayer 2D crystals and vdW heterostructures.« less

Layer and doping tunable ferromagnetic order in two-dimensional Cr S2 layers

NASA Astrophysics Data System (ADS)

Wang, Cong; Zhou, Xieyu; Pan, Yuhao; Qiao, Jingsi; Kong, Xianghua; Kaun, Chao-Cheng; Ji, Wei

2018-06-01

Interlayer coupling is of vital importance for manipulating physical properties, e.g., electronic band gap, in two-dimensional materials. However, tuning magnetic properties in these materials is yet to be addressed. Here, we found the in-plane magnetic orders of Cr S2 mono and few layers are tunable between striped antiferromagnetic (sAFM) and ferromagnetic (FM) orders by manipulating charge transfer between Cr t2 g and eg orbitals. Such charge transfer is realizable through interlayer coupling, direct charge doping, or substituting S with Cl atoms. In particular, the transferred charge effectively reduces a portion of Cr4 + to Cr3 +, which, together with delocalized S p orbitals and their resulting direct S-S interlayer hopping, enhances the double-exchange mechanism favoring the FM rather than sAFM order. An exceptional interlayer spin-exchange parameter was revealed over -10 meV , an order of magnitude stronger than available results of interlayer magnetic coupling. It addition, the charge doping could tune Cr S2 between p - and n -doped magnetic semiconductors. Given these results, several prototype devices were proposed for manipulating magnetic orders using external electric fields or mechanical motion. These results manifest the role of interlayer coupling in modifying magnetic properties of layered materials and shed considerable light on manipulating magnetism in these materials.

Influence of Ni Interlayer on Microstructure and Mechanical Properties of Mg/Al Bimetallic Castings

NASA Astrophysics Data System (ADS)

Liu, Ning; Liu, Canchun; Liang, Chunyong; Zhang, Yongguang

2018-05-01

Dissimilar joining of magnesium and aluminum using a compound casting process was investigated in the present work. For the first time, a Ni interlayer prepared by plasma spraying was inserted between the two base metals to improve the interfacial characteristics. Examination of the interfacial regions using scanning electron microscopy, energy-dispersive X-ray spectroscopy, electron probe microanalysis, and X-ray diffraction revealed the formation of a three-layered interface between Mg and Al without the interlayer. The thickness of the interface was approximately 600 μm when the casting was performed at 700 °C and increased with increasing casting temperature. However, with the addition of the Ni interlayer, the Al-Mg reaction was successfully prevented, and metallurgical bonding between the Ni interlayer and two base metals was achieved at a casting temperature of 700 °C. Upon increasing this temperature, Mg-Ni and Al-Ni intermetallics were generated at the separate interfaces. The shear strength of the Mg/Al bimetallic castings with the Ni interlayer was substantially improved compared with that of the direct Mg/Al joint, with a maximum value of 25.4 MPa achieved at 700 °C. Fracture occurred mainly along the Mg/Ni interface for the Mg/Ni/Al multilayer structure castings.

Ag-Pd-Cu alloy inserted transparent indium tin oxide electrodes for organic solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Hyo-Joong; Seo, Ki-Won; Kim, Han-Ki, E-mail: imdlhkkim@khu.ac.kr

2014-09-01

The authors report on the characteristics of Ag-Pd-Cu (APC) alloy-inserted indium tin oxide (ITO) films sputtered on a glass substrate at room temperature for application as transparent anodes in organic solar cells (OSCs). The effect of the APC interlayer thickness on the electrical, optical, structural, and morphological properties of the ITO/APC/ITO multilayer were investigated and compared to those of ITO/Ag/ITO multilayer electrodes. At the optimized APC thickness of 8 nm, the ITO/APC/ITO multilayer exhibited a resistivity of 8.55 × 10{sup −5} Ω cm, an optical transmittance of 82.63%, and a figure-of-merit value of 13.54 × 10{sup −3} Ω{sup −1}, comparable to those of the ITO/Ag/ITOmore » multilayer. Unlike the ITO/Ag/ITO multilayer, agglomeration of the metal interlayer was effectively relieved with APC interlayer due to existence of Pd and Cu elements in the thin region of the APC interlayer. The OSCs fabricated on the ITO/APC/ITO multilayer showed higher power conversion efficiency than that of OSCs prepared on the ITO/Ag/ITO multilayer below 10 nm due to the flatness of the APC layer. The improved performance of the OSCs with ITO/APC/ITO multilayer electrodes indicates that the APC alloy interlayer prevents the agglomeration of the Ag-based metal interlayer and can decrease the thickness of the metal interlayer in the oxide-metal-oxide multilayer of high-performance OSCs.« less

Scale effect and value criterion of the permeability of the interlayer staggered zones in the basalt of Jinsha River basin, China

NASA Astrophysics Data System (ADS)

Zhou, Zhifang; Lin, Mu; Guo, Qiaona; Chen, Meng

2018-05-01

The hydrogeological characteristics of structural planes are different to those of the associated bedrock. The permeability, and therefore hydraulic conductivity (K), of a structural plane can be significantly different at different scales. The interlayer staggered zones in the Emeishan Basalt of early Late Permian were studied; this formation is located in the Baihetan hydropower project area in Jinsha River Basin, China. The seepage flow distribution of a solid model and two generalized models (A and B) were computed using COMSOL. The K values of the interlayer staggered zones for all three models were calculated by both simulation and analytical methods. The results show that the calculated K results of the generalized models can reflect the variation trend of permeability in each section of the solid model, and the approximate analytical calculation of K can be taken into account in the calculation of K in the generalized models instead of that found by simulation. Further studies are needed to investigate permeability variation in the interlayer staggered zones under the condition of different scales, considering the scaling variation in each section of an interlayer staggered zone. The permeability of each section of an interlayer staggered zone presents a certain degree of dispersivity at small scales; however, the permeability values tends to converge to a similar value as the scale of each section increases. The regularity of each section of the interlayer staggered zones under the condition of different scales can provide a scientific basis for reasonable selection of different engineering options.

Nutrition and Supplementation in Soccer.

PubMed

Oliveira, César Chaves; Ferreira, Diogo; Caetano, Carlos; Granja, Diana; Pinto, Ricardo; Mendes, Bruno; Sousa, Mónica

2017-05-12

Contemporary elite soccer features increased physical demands during match-play, as well as a larger number of matches per season. Now more than ever, aspects related to performance optimization are highly regarded by both players and soccer coaches. Here, nutrition takes a special role as most elite teams try to provide an adequate diet to guarantee maximum performance while ensuring a faster recovery from matches and training exertions. It is currently known that manipulation and periodization of macronutrients, as well as sound hydration practices, have the potential to interfere with training adaptation and recovery. A careful monitoring of micronutrient status is also relevant to prevent undue fatigue and immune impairment secondary to a deficiency status. Furthermore, the sensible use of evidence-based dietary supplements may also play a role in soccer performance optimization. In this sense, several nutritional recommendations have been issued. This detailed and comprehensive review addresses the most relevant and up-to-date nutritional recommendations for elite soccer players, covering from macro and micronutrients to hydration and selected supplements in different contexts (daily requirements, pre, peri and post training/match and competition).

The void in using urine concentration to assess population fluid intake adequacy or hydration status.

PubMed

Cheuvront, Samuel N; Muñoz, Colleen X; Kenefick, Robert W

2016-09-01

Urine concentration can be used to assess fluid intake adequacy or to diagnose dehydration. However, too often urine concentration is used inappropriately to draw dubious conclusions that could have harmful health and economic consequences. Inappropriate uses of urine concentration relate primarily to convenience sampling (timing) and problems related to convenience sampling (misapplication of thresholds), but a conceptual problem also exists with using urine concentration in isolation. The purpose of this Perspective article is to briefly explain the problematic nature of current practices and to offer a possible solution to improve practice with minimal added complication. When urine is used exclusively to assess fluid intake adequacy and hydration status in adults, we propose that only when urine concentration is high (>850 mmol/kg) and urine excretion rate is low (<850 mL/24 h) should suspicion of inadequate drinking or impending dehydration be considered. Prospective tests of the 850 × 850 thresholds will provide supporting evidence and/or help refine the best thresholds for men and women, young and old. © 2016 American Society for Nutrition.

Hydration status of exclusively and partially breastfed near-term newborns in the first week of life.

PubMed

Kusuma, Sirisha; Agrawal, Sunil Kumar; Kumar, Praveen; Narang, Anil; Prasad, Rajendra

2009-08-01

An in-hospital prospective, observational cohort study was conducted to assess the effects of type of feeding (exclusively breastfed [EBF] vs partially breastfed [PBF]) on the hydration status of near-term newborns in the first week of life. A total of 205 babies of 35 to 37 weeks of completed gestation were enrolled (82 in the EBF group and 123 in the PBF group). The overall incidence of significant weight loss (>or=10%) was 18% with no significant difference between EBF and PBF groups (18.3% vs 17.9%, P=.94). The incidence of hypernatremia (serum NA>or=150 meq/L) was 2.4% in the EBF group and 5.7% in the PBF group (P=.32). The factors associated with significant weight loss in the total cohort were having a mother with previous negative breastfeeding experience (adjusted odds ratio [OR]=16.5, 95% confidence interval [CI]=2.1-115.7), exposure to phototherapy (adjusted OR=9.0, 95% CI=2.5-31.8), and cesarean delivery (adjusted OR=6.7, 95% CI=2.3-19.7).

Nutrition and Supplementation in Soccer

PubMed Central

Oliveira, César Chaves; Ferreira, Diogo; Caetano, Carlos; Granja, Diana; Pinto, Ricardo; Mendes, Bruno; Sousa, Mónica

2017-01-01

Contemporary elite soccer features increased physical demands during match-play, as well as a larger number of matches per season. Now more than ever, aspects related to performance optimization are highly regarded by both players and soccer coaches. Here, nutrition takes a special role as most elite teams try to provide an adequate diet to guarantee maximum performance while ensuring a faster recovery from matches and training exertions. It is currently known that manipulation and periodization of macronutrients, as well as sound hydration practices, have the potential to interfere with training adaptation and recovery. A careful monitoring of micronutrient status is also relevant to prevent undue fatigue and immune impairment secondary to a deficiency status. Furthermore, the sensible use of evidence-based dietary supplements may also play a role in soccer performance optimization. In this sense, several nutritional recommendations have been issued. This detailed and comprehensive review addresses the most relevant and up-to-date nutritional recommendations for elite soccer players, covering from macro and micronutrients to hydration and selected supplements in different contexts (daily requirements, pre, peri and post training/match and competition). PMID:29910389

76 FR 19278 - Airworthiness Directives; The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-07

... are proposing this AD to detect and correct cracking in the fail-safe interlayer of certain No. 2 and... to detect and correct cracking in the fail-safe interlayer of certain No. 2 and No. 3 glass windows... cracking in the fail-safe interlayer of certain No. 2 and No. 3 glass windows, which could result in loss...

Obtention of low oxidation states of copper from Cu 2+-Al 3+ layered double hydroxides containing organic sulfonates in the interlayer

NASA Astrophysics Data System (ADS)

Trujillano, Raquel; Holgado, María Jesús; Rives, Vicente

2009-03-01

A series of hydrotalcite-type compounds containing Cu(II) and Al(III) in the layers, and carbonate or different alkylsulfonates in the interlayer, have been prepared and studied. Calcination of these solids gives rise to formation of metallic copper and Cu 2+ and Cu + oxides or sulfates, depending on the calcination temperature and on the precise nature of the interlayer alkylsulfonate.

Analysis of the influence of the interlayer staggered zone in the basalt of Jinsha River Basin on the main buildings

NASA Astrophysics Data System (ADS)

Guo, Qiaona; Huang, Jiangwei

2018-02-01

In this paper, the finite element software FEFLOW is used to simulate the seepage field of the interlayer staggered zone C2 in the basalt of Jinsha River Basin. The influence of the interlayer staggered zone C2 on the building is analyzed. Combined with the waterproof effect of current design scheme of anti-seepage curtain, the seepage field in the interlayer staggered zone C2 is discussed under different design schemes. The optimal design scheme of anti-seepage curtain is put forward. The results showed that the case four can effectively reduce the head and hydraulic gradient of underground powerhouse area, and improve the groundwater seepage field in the plant area.

Interlayer toughening of fiber composite flywheel rotors

DOEpatents

Groves, Scott E.; Deteresa, Steven J.

1998-01-01

An interlayer toughening mechanism to mitigate the growth of damage in fiber composite flywheel rotors for long application. The interlayer toughening mechanism may comprise one or more tough layers composed of high-elongation fibers, high-strength fibers arranged in a woven pattern at a range from 0.degree. to 90.degree. to the rotor axis and bound by a ductile matrix material which adheres to and is compatible with the materials used for the bulk of the rotor. The number and spacing of the tough interlayers is a function of the design requirements and expected lifetime of the rotor. The mechanism has particular application in uninterruptable power supplies, electrical power grid reservoirs, and compulsators for electric guns, as well as electromechanical batteries for vehicles.

Interlayer toughening of fiber composite flywheel rotors

DOEpatents

Groves, S.E.; Deteresa, S.J.

1998-07-14

An interlayer toughening mechanism is described to mitigate the growth of damage in fiber composite flywheel rotors for long application. The interlayer toughening mechanism may comprise one or more tough layers composed of high-elongation fibers, high-strength fibers arranged in a woven pattern at a range from 0{degree} to 90{degree} to the rotor axis and bound by a ductile matrix material which adheres to and is compatible with the materials used for the bulk of the rotor. The number and spacing of the tough interlayers is a function of the design requirements and expected lifetime of the rotor. The mechanism has particular application in uninterruptable power supplies, electrical power grid reservoirs, and compulsators for electric guns, as well as electromechanical batteries for vehicles. 2 figs.

Carrier-selective interlayer materials for silicon solar cell contacts

NASA Astrophysics Data System (ADS)

Xue, Muyu; Islam, Raisul; Chen, Yusi; Chen, Junyan; Lu, Ching-Ying; Mitchell Pleus, A.; Tae, Christian; Xu, Ke; Liu, Yi; Kamins, Theodore I.; Saraswat, Krishna C.; Harris, James S.

2018-04-01

This work presents titanium oxide (TiOx) and nickel oxide (NiOx) as promising carrier-selective interlayer materials for metal-interlayer-semiconductor contacts for silicon solar cells. The electron-conducting, hole-blocking behavior of TiOx and the opposite carrier-selective behavior of NiOx are investigated using the transmission-line-method. The Fermi level depinning effect and the tunneling resistance are demonstrated to be dependent on the interlayer oxide thickness and annealing temperature. NiOx is furthermore experimentally demonstrated to be capable of improving the effective minority carrier lifetime by quasi-steady-state photoconductance method. Our study demonstrates that TiOx and NiOx can be effective carrier-selective materials for Si solar cells and provides a framework for characterizing carrier-selective contacts.

Distributed bragg reflector using AIGaN/GaN

DOEpatents

Waldrip, Karen E.; Lee, Stephen R.; Han, Jung

2004-08-10

A supported distributed Bragg reflector or superlattice structure formed from a substrate, a nucleation layer deposited on the substrate, and an interlayer deposited on the nucleation layer, followed by deposition of (Al,Ga,B)N layers or multiple pairs of (Al,Ga,B)N/(Al,Ga,B)N layers, where the interlayer is a material selected from AlN, Al.sub.x Ga.sub.1-x N, and AlBN with a thickness of approximately 20 to 1000 angstroms. The interlayer functions to reduce or eliminate the initial tensile growth stress, thereby reducing cracking in the structure. Multiple interlayers utilized in an AlGaN/GaN DBR structure can eliminate cracking and produce a structure with a reflectivity value greater than 0.99.

Optimizing fluid management in patients with acute decompensated heart failure (ADHF): the emerging role of combined measurement of body hydration status and brain natriuretic peptide (BNP) levels.

PubMed

Valle, Roberto; Aspromonte, Nadia; Milani, Loredano; Peacock, Frank W; Maisel, Alan S; Santini, Massimo; Ronco, Claudio

2011-11-01

The study tests the hypothesis that in patients admitted with acutely decompensated heart failure (ADHF), achievement of adequate body hydration status with intensive medical therapy, modulated by combined bioelectrical vectorial impedance analysis (BIVA) and B-type natriuretic peptide (BNP) measurement, may contribute to optimize the timing of patient's discharge and to improve clinical outcomes. Three hundred patients admitted for ADHF underwent serial BIVA and BNP measurement. Therapy was titrated to reach a BNP value of <250 pg/ml, whenever possible. Patients were categorized as early responders (rapid BNP fall below 250 pg/ml); late responders (slow BNP fall below 250 pg/ml, after aggressive therapy); and non-responders (BNP persistently >250 pg/ml). Worsening of renal function (WRF) was evaluated during hospitalization. Death and rehospitalization were monitored with a 6-month follow-up. BNP value on discharge of ≤250 pg/ml led to a 25% event rate within 6 months (Group A: 17.4%; Group B: 21%, Chi2; n.s.), whereas a value >250 pg/ml (Group C) was associated with a far higher percentage (37%). At discharge, body hydration was 73.8 ± 3.2% in the total population and 73.2 ± 2.1, 73.5 ± 2.8, 74.1 ± 3.6% in the three groups, respectively. WRF was observed in 22.3% of the total. WRF occurred in 22% in Group A, 32% in Group B, and 20% in Group C (P = n.s.). Our study confirms the hypothesis that combined BNP/BIVA sequential measurements help to achieve adequate fluid balance status in patients with ADHF and can be used to drive a "tailored therapy," allowing clinicians to identify high-risk patients and possibly to reduce the incidence of complications secondary to fluid management strategies.

Reliability of Urinary Dehydration Markers in Elite Youth Boxers.

PubMed

Zubac, Damir; Cular, Drazen; Marusic, Uros

2018-03-01

To determine the reliability and diagnostic accuracy of noninvasive urinary dehydration markers in field-based settings on a day-to-day basis in elite adolescent amateur boxers. Sixty-nine urine samples were collected daily from 23 athletes (17.3 ± 1.9 y) during their weight-stable phase and analyzed by field and laboratory measures of hydration status. Urine osmolality (U OSM ), urine specific gravity (U SG ), total protein content (T PC ), and body-mass stability were evaluated to determine fluid balance and hydration status. Overall macronutrient and water intake were determined using dietary records. According to their anthropometric characteristics, athletes were assigned into 2 groups: lightweight (L WB ) and heavyweight (H WB ) boxers. Data presented on U OSM demonstrated a uniform increment by 11.2% ± 12.8% (L WB ) and 19.9% ± 22.7% (H WB ) (P < .001) over the course of the study, even during the weight-stable phase (body mass, ICC = .99) and ad libitum fluid intake (42 ± 4 mL · kg -1  · d -1 ). The intraclass correlation coefficients (ICCs) ranged from .52 to .55 for U SG and .38 to .52 for U OSM , further indicating inconsistency of the urinary dehydration markers. Poor correlations were found between U SG and T PC metabolites (r = .27, P = .211). Urinary dehydration markers (both U SG and U OSM ) exhibit high variability and seem to be unreliable diagnostic tools to track actual body-weight loss in real-life settings. The ad libitum fluid intake was apparently inadequate to match acute fluid loss during and after intense preparation. The applicability of a single-time-point hydration-status assessment concept may preclude accurate assessment of actual body-weight deficits in youth boxers.

Usefulness of ultrasound examination in the evaluation of a neonate's body fluid status.

PubMed

Kieliszczyk, Joanna; Baranowski, Wojciech; Kosiak, Wojciech

2016-06-01

Appropriate hydration is a very important prognostic factor for the patient's health. Ultrasonographic assessment of hydration status is rarely used in pediatric medicine and it is not used at all in neonates due to the fact that no reference values have been established for this age group. The aim of the paper was to establish reference values for neonates. The study included 50 neonates from two hospitals in the Lower Silesia region of Poland; 25 of them were healthy patients (full-term newborns with no perinatal complications) and 25 were sick patients (newborns with heart defects such as ostium secundum atrial septal defect, ventricular septal defect, permanent foramen ovale and patent ductus arteriosus as well as newborns with neonatal jaundice or pneumonia that occurred during the first days of life). The ultrasound scans were conducted during the first days of the children's life. For every child inferior vena cava diameter was measured in the substernal area, longitudinal plane, M-mode in two respiratory phases: inhalation and exhalation. In addition, abdominal aorta diameter was determined (substernal area, transverse plane). The study demonstrated a statistically significant difference in the calculated inferior vena cava collapsibility index between both groups. Two other indices included the ratio of the inferior vena cava diameter during the expiratory phase to the diameter of the aorta and the ratio of the inferior vena cava diameter during the inspiratory phase to the diameter of the aorta; a statistically significant difference between both groups was found only for the measurements in the inspiratory phase. Based on the study results normal ranges for hydration indices in neonates were established. The need for the measurement of the abovementioned parameters in the inspiratory phase was determined. In addition, the usefulness of the ultrasound examination for the evaluation of body fluid status in this pediatric age group, particularly in preterm newborns, was noted due to its painless and non-invasive nature as well as easy access to equipment at neonatology wards.

Polytypism and unexpected strong interlayer coupling in two-dimensional layered ReS2

NASA Astrophysics Data System (ADS)

Qiao, Xiao-Fen; Wu, Jiang-Bin; Zhou, Linwei; Qiao, Jingsi; Shi, Wei; Chen, Tao; Zhang, Xin; Zhang, Jun; Ji, Wei; Tan, Ping-Heng

2016-04-01

Anisotropic two-dimensional (2D) van der Waals (vdW) layered materials, with both scientific interest and application potential, offer one more dimension than isotropic 2D materials to tune their physical properties. Various physical properties of 2D multi-layer materials are modulated by varying their stacking orders owing to significant interlayer vdW coupling. Multilayer rhenium disulfide (ReS2), a representative anisotropic 2D material, was expected to be randomly stacked and lack interlayer coupling. Here, we demonstrate two stable stacking orders, namely isotropic-like (IS) and anisotropic-like (AI) N layer (NL, N > 1) ReS2 are revealed by ultralow- and high-frequency Raman spectroscopy, photoluminescence and first-principles density functional theory calculation. Two interlayer shear modes are observed in AI-NL-ReS2 while only one shear mode appears in IS-NL-ReS2, suggesting anisotropic- and isotropic-like stacking orders in IS- and AI-NL-ReS2, respectively. This explicit difference in the observed frequencies identifies an unexpected strong interlayer coupling in IS- and AI-NL-ReS2. Quantitatively, the force constants of them are found to be around 55-90% of those of multilayer MoS2. The revealed strong interlayer coupling and polytypism in multi-layer ReS2 may stimulate future studies on engineering physical properties of other anisotropic 2D materials by stacking orders.Anisotropic two-dimensional (2D) van der Waals (vdW) layered materials, with both scientific interest and application potential, offer one more dimension than isotropic 2D materials to tune their physical properties. Various physical properties of 2D multi-layer materials are modulated by varying their stacking orders owing to significant interlayer vdW coupling. Multilayer rhenium disulfide (ReS2), a representative anisotropic 2D material, was expected to be randomly stacked and lack interlayer coupling. Here, we demonstrate two stable stacking orders, namely isotropic-like (IS) and anisotropic-like (AI) N layer (NL, N > 1) ReS2 are revealed by ultralow- and high-frequency Raman spectroscopy, photoluminescence and first-principles density functional theory calculation. Two interlayer shear modes are observed in AI-NL-ReS2 while only one shear mode appears in IS-NL-ReS2, suggesting anisotropic- and isotropic-like stacking orders in IS- and AI-NL-ReS2, respectively. This explicit difference in the observed frequencies identifies an unexpected strong interlayer coupling in IS- and AI-NL-ReS2. Quantitatively, the force constants of them are found to be around 55-90% of those of multilayer MoS2. The revealed strong interlayer coupling and polytypism in multi-layer ReS2 may stimulate future studies on engineering physical properties of other anisotropic 2D materials by stacking orders. Electronic supplementary information (ESI) available. See DOI: 10.1039/c6nr01569g

Crystal water dynamics of guanosine dihydrate: analysis of atomic displacement parameters, time profile of hydrogen-bonding probability, and translocation of water by MD simulation.

PubMed

Yoneda, Shigetaka; Sugawara, Yoko; Urabe, Hisako

2005-01-27

The dynamics of crystal water molecules of guanosine dihydrate are investigated in detail by molecular dynamics (MD) simulation. A 2 ns simulation is performed using a periodic boundary box composed of 4 x 5 x 8 crystallographic unit cells and using the particle-mesh Ewald method for calculation of electrostatic energy. The simulated average atomic positions and atomic displacement parameters are remarkably coincident with the experimental values determined by X-ray analysis, confirming the high accuracy of this simulation. The dynamics of crystal water are analyzed in terms of atomic displacement parameters, orientation vectors, order parameters, self-correlation functions of the orientation vectors, time profiles of hydrogen-bonding probability, and translocations. The simulation clarifies that the average structure is composed of various stable and transient structures of the molecules. The simulated guanosine crystal forms a layered structure, with four water sites per asymmetric unit, classified as either interlayer water or intralayer water. From a detailed analysis of the translocations of water molecules in the simulation, columns of intralayer water molecules along the c axis appear to represent a pathway for hydration and dehydration by a kind of molecular valve mechanism.

Effect on physical properties of laterite soil with difference percentage of sodium bentonite

NASA Astrophysics Data System (ADS)

Kasim, Nur Aisyah; Azmi, Nor Azizah Che; Mukri, Mazidah; Noor, Siti Nur Aishah Mohd

2017-08-01

This research was carried out in an attempt to know the physical properties of laterite soil with the appearance of difference percentage of sodium bentonite. Lateritic soils usually develop in tropical and other regions with similar hot and humid climate, where heavy rainfall, warm temperature and well drainage lead to the formation of thick horizons of reddish lateritic soil profiles rich in iron and aluminium. When sodium predominates, a large amount of water can be absorbed in the interlayer, resulting in the remarkable swelling properties observed with hydrating sodium bentonite. There are some basic physical properties test conducted in this research which are Specific Gravity Test, pH Test, Sieve Analysis, Hydrometer Test, Shrinkage Limit and Atterberg Limit. The test will be conducted with 0%, 5%, 10%, 15% and 20% of sodium bentonite. Each test will be repeated three times for the accuracy of the result. From the physical properties test the soil properties characteristic react with the sodium bentonite can be determine. Therefore the best percentage of sodium bentonite admixture can be determined for laterite soil. The outcomes of this study give positive results due to the potential of sodium bentonite to improve the laterite soil particle.

Graphene-Based Environmental Barriers

PubMed Central

Guo, Fei; Silverberg, Gregory; Bowers, Shin; Kim, Sang-Pil; Datta, Dibakar; Shenoy, Vivek; Hurt, Robert H.

2012-01-01

Many environmental technologies rely on containment by engineered barriers that inhibit the release or transport of toxicants. Graphene is a new, atomically thin, two-dimensional sheet material, whose aspect ratio, chemical resistance, flexibility, and impermeability make it a promising candidate for inclusion in a next generation of engineered barriers. Here we show that ultrathin graphene oxide (GO) films can serve as effective barriers for both liquid and vapor permeants. First, GO deposition on porous substrates is shown to block convective flow at much lower mass loadings than other carbon nanomaterials, and can achieve hydraulic conductivities of 5×10−12 cm/s or lower. Second we show that ultrathin GO films of only 20 nm thickness coated on polyethylene films reduce their vapor permeability by 90% using elemental mercury as a model vapor toxicant. The barrier performance of GO in this thin-film configuration is much better than the Nielsen model limit, which describes ideal behavior of flake-like fillers uniformly imbedded in a polymer. The Hg barrier performance of GO films is found to be sensitive to residual water in the films, which is consistent with molecular dynamics (MD) simulations that show lateral diffusion of Hg atoms in graphene interlayer spaces that have been expanded by hydration. PMID:22717015

Characterization of the mechanical and thermal interface of copper films on carbon substrates modified by boron based interlayers

PubMed Central

Schäfer, D.; Eisenmenger-Sittner, C.; Chirtoc, Mihai; Kijamnajsuk, P.; Kornfeind, N.; Hutter, H.; Neubauer, E.; Kitzmantel, M.

2011-01-01

The manipulation of mechanical and thermal interfaces is essential for the design of modern composites. Amongst these are copper carbon composites which can exhibit excellent heat conductivities if the Cu/C interface is affected by a suitable interlayer to minimize the Thermal Contact Resistance (TCR) and to maximize the adhesion strength between Cu and C. In this paper we report on the effect of boron based interlayers on wetting, mechanical adhesion and on the TCR of Cu coatings deposited on glassy carbon substrates by magnetron sputtering. The interlayers were 5 nm thick and consisted of pure B and B with additions of the carbide forming metals Mo, Ti and Cr in the range of 5 at.% relative to B. The interlayers were deposited by RF magnetron sputtering from either a pure B target or from a composite target. The interlayer composition was checked by Auger Electron Spectroscopy and found to be homogenous within the whole film. The system C-substrate/interlayer/Cu coating was characterized in as deposited samples and samples heat treated for 30 min at 800 °C under High Vacuum (HV), which mimics typical hot pressing parameters during composite formation. Material transport during heat treatment was investigated by Secondary Ion Mass Spectroscopy (SIMS). The de-wetting and hole formation in the Cu coating upon heat treatment were studied by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The adhesion of the Cu coating was evaluated by mechanical pull-off testing. The TCR was assessed by infrared photothermal radiometry (PTR). A correlation between the adhesion strength and the value of the TCR which was measured by PTR was determined for as deposited as well as for heat treated samples. PMID:22241938

Robust Stacking-Independent Ultrafast Charge Transfer in MoS2/WS2 Bilayers.

PubMed

Ji, Ziheng; Hong, Hao; Zhang, Jin; Zhang, Qi; Huang, Wei; Cao, Ting; Qiao, Ruixi; Liu, Can; Liang, Jing; Jin, Chuanhong; Jiao, Liying; Shi, Kebin; Meng, Sheng; Liu, Kaihui

2017-12-26

Van der Waals-coupled two-dimensional (2D) heterostructures have attracted great attention recently due to their high potential in the next-generation photodetectors and solar cells. The understanding of charge-transfer process between adjacent atomic layers is the key to design optimal devices as it directly determines the fundamental response speed and photon-electron conversion efficiency. However, general belief and theoretical studies have shown that the charge transfer behavior depends sensitively on interlayer configurations, which is difficult to control accurately, bringing great uncertainties in device designing. Here we investigate the ultrafast dynamics of interlayer charge transfer in a prototype heterostructure, the MoS 2 /WS 2 bilayer with various stacking configurations, by optical two-color ultrafast pump-probe spectroscopy. Surprisingly, we found that the charge transfer is robust against varying interlayer twist angles and interlayer coupling strength, in time scale of ∼90 fs. Our observation, together with atomic-resolved transmission electron characterization and time-dependent density functional theory simulations, reveals that the robust ultrafast charge transfer is attributed to the heterogeneous interlayer stretching/sliding, which provides additional channels for efficient charge transfer previously unknown. Our results elucidate the origin of transfer rate robustness against interlayer stacking configurations in optical devices based on 2D heterostructures, facilitating their applications in ultrafast and high-efficient optoelectronic and photovoltaic devices in the near future.

Enhanced performance of lithium-sulfur batteries with an ultrathin and lightweight MoS2/carbon nanotube interlayer

NASA Astrophysics Data System (ADS)

Yan, Lingjia; Luo, Nannan; Kong, Weibang; Luo, Shu; Wu, Hengcai; Jiang, Kaili; Li, Qunqing; Fan, Shoushan; Duan, Wenhui; Wang, Jiaping

2018-06-01

Ultrathin and lightweight MoS2/carbon nanotube (CNT) interlayers are developed to effectively trap polysulfides in high-performance lithium-sulfur (Li-S) batteries. The MoS2/CNT interlayer is constructed by loading MoS2 nanosheets onto a cross-stacked CNT film. The CNT film with excellent conductivity and superior mechanical properties provides the Li-S batteries with a uniform conductive network, a supporting skeleton for the MoS2 nanosheets, as well as a physical barrier for the polysulfides. Moreover, chemical interactions and bonding between the MoS2 nanosheets and the polysulfides are evident. The electrode with the MoS2/CNT interlayer delivers an attractive specific capacity of 784 mA h g-1 at a high capacity rate of 10 C. In addition, the electrode demonstrates a high initial capacity of 1237 mA h g-1 and a capacity fade as low as -0.061% per cycle over 500 charge/discharge cycles at 0.2 C. The problem of self-discharge can also be suppressed with the introduction of the MoS2/CNT interlayer. The simple fabrication procedure, which is suitable for commercialization, and the outstanding electrochemical performance of the cells with the MoS2/CNT interlayer demonstrate a great potential for the development of high-performance Li-S batteries.

Designing interlayers to improve the mechanical reliability of transparent conductive oxide coatings on flexible substrates

NASA Astrophysics Data System (ADS)

Kim, Eun-Hye; Yang, Chan-Woo; Park, Jin-Woo

2012-05-01

In this study, we investigate the effect of interlayers on the mechanical properties of transparent conductive oxide (TCO) on flexible polymer substrates. Indium tin oxide (ITO), which is the most widely used TCO film, and Ti, which is the most widely used adhesive interlayer, are selected as the coating and the interlayer, respectively. These films are deposited on the polymer substrates using dc-magnetron sputtering to achieve varying thicknesses. The changes in the following critical factors for film cracking and delamination are analyzed: the internal stress (σi) induced in the coatings during deposition using a white light interferometer, the crystallinity using a transmission electron microscope, and the surface roughness of ITO caused by the interlayer using an atomic force microscope. The resistances to the cracking and delamination of ITO are evaluated using a fragmentation test. Our tests and analyses reveal the important role of the interlayers, which significantly reduce the compressive σi that is induced in the ITO and increase the resistance to the buckling delamination of the ITO. However, the relaxation of σi is not beneficial to cracking because there is less compensation for the external tension as σi further decreases. Based on these results, the microstructural control is revealed as a more influential factor than σi for improving crack resistance.

Brightened spin-triplet interlayer excitons and optical selection rules in van der Waals heterobilayers

NASA Astrophysics Data System (ADS)

Yu, Hongyi; Liu, Gui-Bin; Yao, Wang

2018-07-01

We investigate the optical properties of spin-triplet interlayer excitons in heterobilayer transition metal dichalcogenides in comparison with the spin-singlet ones. Surprisingly, the optical transition dipole of the spin-triplet exciton is found to be in the same order of magnitude to that of the spin-singlet exciton, in sharp contrast to the monolayer excitons where the spin-triplet species is considered as dark compared to the singlet. Unlike the monolayer excitons whose spin-conserved (spin-flip) transition dipole can only couple to light of in-plane (out-of-plane) polarisation, such restriction is removed for the interlayer excitons due to the breaking of the out-of-plane mirror symmetry. We find that as the interlayer atomic registry changes, the optical transition dipole of interlayer exciton crosses between in-plane ones of opposite circular polarizations and the out-of-plane one for both the spin-triplet and spin-singlet species. As a result, excitons of both species have non-negligible coupling into photon modes of both in-plane and out-of-plane propagations, another sharp difference from the monolayers where the exciton couples predominantly into the out-of-plane propagation channel. At given atomic registry, the spin-triplet and spin-singlet excitons have distinct valley polarisation selection rules, allowing the selective optical addressing of both the valley configuration and the spin-singlet/triplet configuration of interlayer excitons.

Tuning Coupling Behavior of Stacked Heterostructures Based on MoS2, WS2, and WSe2

PubMed Central

Wang, Fang; Wang, Junyong; Guo, Shuang; Zhang, Jinzhong; Hu, Zhigao; Chu, Junhao

2017-01-01

The interlayer interaction of vertically stacked heterojunctions is very sensitive to the interlayer spacing, which will affect the coupling between the monolayers and allow band structure modulation. Here, with the aid of density functional theory (DFT) calculations, an interesting phenomenon is found that MoS2-WS2, MoS2-WSe2, and WS2-WSe2 heterostructures turn into direct-gap semiconductors from indirect-gap semiconductors with increasing the interlayer space. Moreover, the electronic structure changing process with interlayer spacing of MoS2-WS2, MoS2-WSe2, and WS2-WSe2 is different from each other. With the help of variable-temperature spectral experiment, different electronic transition properties of MoS2-WS2, MoS2-WSe2, and WS2-WSe2 have been demonstrated. The transition transformation from indirect to direct can be only observed in the MoS2-WS2 heterostructure, as the valence band maximum (VBM) at the Γ point in the MoS2-WSe2 and WS2-WSe2 heterostructure is less sensitive to the interlayer spacing than those from the MoS2-WS2 heterostructure. The present work highlights the significance of the temperature tuning in interlayer coupling and advance the research of MoS2-WS2, MoS2-WSe2, and WS2-WSe2 based device applications. PMID:28303932

A shape-based inter-layer contours correspondence method for ICT-based reverse engineering

PubMed Central

Duan, Liming; Yang, Shangpeng; Zhang, Gui; Feng, Fei; Gu, Minghui

2017-01-01

The correspondence of a stack of planar contours in ICT (industrial computed tomography)-based reverse engineering, a key step in surface reconstruction, is difficult when the contours or topology of the object are complex. Given the regularity of industrial parts and similarity of the inter-layer contours, a specialized shape-based inter-layer contours correspondence method for ICT-based reverse engineering was presented to solve the above problem based on the vectorized contours. In this paper, the vectorized contours extracted from the slices consist of three graphical primitives: circles, arcs and segments. First, the correspondence of the inter-layer primitives is conducted based on the characteristics of the primitives. Second, based on the corresponded primitives, the inter-layer contours correspond with each other using the proximity rules and exhaustive search. The proposed method can make full use of the shape information to handle industrial parts with complex structures. The feasibility and superiority of this method have been demonstrated via the related experiments. This method can play an instructive role in practice and provide a reference for the related research. PMID:28489867

A shape-based inter-layer contours correspondence method for ICT-based reverse engineering.

PubMed

Duan, Liming; Yang, Shangpeng; Zhang, Gui; Feng, Fei; Gu, Minghui

2017-01-01

The correspondence of a stack of planar contours in ICT (industrial computed tomography)-based reverse engineering, a key step in surface reconstruction, is difficult when the contours or topology of the object are complex. Given the regularity of industrial parts and similarity of the inter-layer contours, a specialized shape-based inter-layer contours correspondence method for ICT-based reverse engineering was presented to solve the above problem based on the vectorized contours. In this paper, the vectorized contours extracted from the slices consist of three graphical primitives: circles, arcs and segments. First, the correspondence of the inter-layer primitives is conducted based on the characteristics of the primitives. Second, based on the corresponded primitives, the inter-layer contours correspond with each other using the proximity rules and exhaustive search. The proposed method can make full use of the shape information to handle industrial parts with complex structures. The feasibility and superiority of this method have been demonstrated via the related experiments. This method can play an instructive role in practice and provide a reference for the related research.

Interplay between Interfacial Structures and Device Performance in Organic Solar Cells: A Case Study with the Low Work Function Metal, Calcium.

PubMed

Ju, Huanxin; Knesting, Kristina M; Zhang, Wei; Pan, Xiao; Wang, Chia-Hsin; Yang, Yaw-Wen; Ginger, David S; Zhu, Junfa

2016-01-27

A better understanding of how interfacial structure affects charge carrier recombination would benefit the development of highly efficient organic photovoltaic (OPV) devices. In this paper, transient photovoltage (TPV) and charge extraction (CE) measurements are used in combination with synchrotron radiation photoemission spectroscopy (SRPES) to gain insight into the correlation between interfacial properties and device performance. OPV devices based on PCDTBT/PC71BM with a Ca interlayer were studied as a reference system to investigate the interfacial effects on device performance. Devices with a Ca interlayer exhibit a lower recombination than devices with only an Al cathode at a given charge carrier density (n). In addition, the interfacial band structures indicate that the strong dipole moment produced by the Ca interlayer can facilitate the extraction of electrons and drive holes away from the cathode/polymer interface, resulting in beneficial reduction in interfacial recombination losses. These results help explain the higher efficiencies of devices made with Ca interlayers compared to that without the Ca interlayer.

TEM Analysis of Diffusion-Bonded Silicon Carbide Ceramics Joined Using Metallic Interlayers

NASA Technical Reports Server (NTRS)

Ozaki, T.; Tsuda, H.; Halbig, M. C.; Singh, M.; Hasegawa, Y; Mori, S.; Asthana, R.

2017-01-01

Silicon Carbide (SiC) is a promising material for thermostructural applications due to its excellent high-temperature mechanical properties, oxidation resistance, and thermal stability. However, joining and integration technologies are indispensable for this material in order to fabricate large size and complex shape components with desired functionalities. Although diffusion bonding techniques using metallic interlayers have been commonly utilized to bond various SiC ceramics, detailed microstructural observation by Transmission Electron Microscopy (TEM) of the bonded area has not been carried out due to difficulty in preparing TEM samples. In this study, we tried to prepare TEM samples from joints of diffusion bonded SiC ceramics by Focused Ion Beam (FIB) system and carefully investigated the interfacial microstructure by TEM analysis. The samples used in this study were SiC fiber bonded ceramics (SA-Tyrannohex: SA-THX) diffusion bonded with metallic interlayers such as Ti, TiMo, Mo-B and TiCu. In this presentation, we report the microstructure of diffusion bonded SA-THX mainly with TiCu interlayers obtained by TEM observations, and the influence of metallic interlayers on the joint microstructure and microhardness will be discussed.

Polarization Coupling in Ferroelectric Multilayers as a Function of Interface Charge Concentration

NASA Astrophysics Data System (ADS)

Okatan, Mahmut; Mantese, Joseph; Alpay, Pamir

2009-03-01

Intriguing properties of multilayered and graded ferroelectrics follow from the electrostatic and electromechanical interactions. The strength of the interlayer coupling depends on the concentration of interfacial defects with short-range local electrostatic fields. Defects may locally relax polarization differences and thus reduce the commensurate bound charge concentration at the interlayer interfaces. In this talk, we develop a theoretical analysis based on non-linear thermodynamics coupled with basic electrostatic relations to understand the role of charge compensation at the interlayer interfaces. The results show multilayered ferroelectrics with systematic variations in the composition may display a colossal dielectric response depending upon the interlayer electrostatic interactions. It is expected that other properties such as the pyroelectric and piezoelectric response will yield concomitant increases through the dielectric permittivity.

Interlayer Pairing Symmetry of Composite Fermions in Quantum Hall Bilayers

DOE PAGES

Isobe, Hiroki; Fu, Liang

2017-04-17

Here, we study the pairing symmetry of the interlayer paired state of composite fermions in quantum Hall bilayers. Based on the Halperin-Lee-Read (HLR) theory, the effect of the long-range Coulomb interaction and the internal Chern-Simons gauge fluctuation is analyzed with the random-phase approximation beyond the leading order contribution in small momentum expansion, and we observe that the interlayer paired states with a relative angular momentummore » $l=+1$ are energetically favored for filling ν=$$\\frac{1}2$$+$$\\frac{1}2$$ and $$\\frac{1}4$$+$$\\frac{1}4$$. The degeneracy between states with $±l$ is lifted by the interlayer density-current interaction arising from the interplay of the long-range Coulomb interaction and the Chern-Simons term in the HLR theory.« less

Reduction-responsive interlayer-crosslinked micelles prepared from star-shaped copolymer via click chemistry for drug controlled release

NASA Astrophysics Data System (ADS)

Dai, Yu; Wang, Hongquan; Zhang, Xiaojin

2017-12-01

To improve the stability of polymeric micelles, here we describe interlayer-crosslinked micelles prepared from star-shaped copolymer via click chemistry. The formation of interlayer-crosslinked micelles was investigated and confirmed by proton nuclear magnetic resonance, Fourier-transform infrared spectroscopy, and fluorescence spectroscopy. The morphology of un-crosslinked micelles and crosslinked micelles observed by transmission electron microscope is both uniform nano-sized spheres (approximately 20 nm). The crosslinking enhances the stability of polymeric micelles and improves the drug loading capacity of polymeric micelles. The interlayer-crosslinked micelles prepared from star-shaped copolymer and a crosslinker containing a disulfide bond are reduction-responsive and can release the drug quickly in the presence of the reducing agents such as glutathione (GSH).

Effects of interlayer Sn-Sn lone pair interaction on the band gap of bulk and nanosheet SnO

NASA Astrophysics Data System (ADS)

Umezawa, Naoto; Zhou, Wei

2015-03-01

Effects of interlayer lone-pair interactions on the electronic structure of SnO are firstly explored by the density-functional theory. Our comprehensive study reveals that the band gap of SnO opens as increase in the interlayer Sn-Sn distance. The effect is rationalized by the character of band edges which consists of bonding and anti-bonding states from interlayer lone pair interactions. The band edges for several nanosheets and strained double-layer SnO are estimated. We conclude that the double-layer SnO is a promising material for visible-light driven photocatalyst for hydrogen evolution. This work is supported by the Japan Science and Technology Agency (JST) Precursory Research for Embryonic Science and Technology (PRESTO) program.

Association between preoperative hydration status and acute kidney injury in patients managed surgically for kidney tumours.

PubMed

Ellis, Robert J; Del Vecchio, Sharon J; Kalma, Benjamin; Ng, Keng Lim; Morais, Christudas; Francis, Ross S; Gobe, Glenda C; Ferris, Rebekah; Wood, Simon T

2018-07-01

The purpose of this study was to investigate whether preoperative dehydration and intraoperative hypotension were associated with postoperative acute kidney injury in patients managed surgically for kidney tumours. A retrospective analysis of 184 patients who underwent nephrectomy at a single centre was performed, investigating associations between acute kidney injury after nephrectomy, and both intraoperative hypotension and preoperative hydration/volume status. Intraoperative hypotension was defined as mean arterial pressure < 60 mmHg for ≥ 5 min. Urine conductivity was evaluated as a surrogate measure of preoperative hydration (euhydrated < 15 mS/cm; mildly dehydrated 15-20 mS/cm; dehydrated > 20 mS/cm). Multivariable logistic regression was used to evaluate associations between exposures and the primary outcome, with adjustment made for potential confounders. Patients who were dehydrated and mildly dehydrated had an increased risk of acute kidney injury (adjusted odds ratio [aOR] 4.1, 95% CI 1.3-13.5; and aOR 2.4, 95% CI 1.1-5.3, respectively) compared with euhydrated patients (p = 0.009). Surgical approach appeared to modify this effect, where dehydrated patients undergoing laparoscopic surgery were most likely to develop acute kidney injury, compared with patients managed using an open approach. Intraoperative hypotension was not associated with acute kidney injury. Preoperative dehydration may be associated with postoperative acute kidney injury. Avoiding dehydration in the preoperative period may be advisable, and adherence to international evidence-based guidelines on preoperative fasting is recommended.

Urine specific gravity as an indicator of dehydration in Olympic combat sport athletes; considerations for research and practice.

PubMed

Zubac, Damir; Reale, Reid; Karnincic, Hrvoje; Sivric, Anamaria; Jelaska, Igor

2018-05-10

Urine specific gravity (U SG ) is the most commonly reported biochemical marker used in research and applied settings to detect fluid deficits in athletes, including those participating in combat sports. Despite the popularity of its use, there has been a growing debate regarding the diagnostic accuracy and the applicability of U SG in characterizing whole-body fluid status and fluctuations. Moreover, recent investigations report universally high prevalence of hypohydration (∼90%) via U SG assessment in combat sport athletes, often in spite of stable body-mass. Given the widespread use in both research and practice, and its use in a regulatory sense as a 'hydration test' in combat sports as a means to detect dehydration at the time of weigh-in; understanding the limitations and applicability of U SG assessment is of paramount importance. Inconsistencies in findings of U SG readings, possibly as a consequence of diverse methodological research approaches and/or overlooked confounding factors, preclude a conclusive position stand within current combat sports research and practice. Thus the primary aim of this paper is to critically review the literature regarding U SG assessment of hydration status in combat sports research and practice. When taken on balance, the existing literature suggests: the use of laboratory derived benchmarks in applied settings, inconsistent sampling methodologies, the incomplete picture of how various confounding factors affect end-point readings, and the still poorly understood potential of renal adaptation to dehydration in combat athletes; make the utility of hydration assessment via U SG measurement quite problematic, particularly when diet and training is not controlled.

Interfacial Characteristics of Efficient Bulk Heterojunction Solar Cells Fabricated on MoOx Anode Interlayers.

PubMed

Jasieniak, Jacek J; Treat, Neil D; McNeill, Christopher R; de Villers, Bertrand J Tremolet; Della Gaspera, Enrico; Chabinyc, Michael L

2016-05-01

The role of the interface between an MoOx anode interlayer and a polymer:fullerene bulk heterojunction is investigated. Processing differences in the MoOx induce large variations in the vertical stratification of the bulk heterojunction films. These variations are found to be inconsistent in predicting device performance, with a much better gauge being the quantity of polymer chemisorbed to the anode interlayer. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydration and urinary pseudoephedrine levels after a simulated team game.

PubMed

Jolley, Daniel; Dawson, Brian; Maloney, Shane K; White, James; Goodman, Carmel; Peeling, Peter

2014-06-01

This study investigated the influence of dehydration on urinary levels of pseudoephedrine (PSE) after prolonged repeated effort activity. Fourteen athletes performed a simulated team game circuit (STGC) outdoors over 120 min under three different hydration protocols: hydrated (HYD), dehydrated (DHY) and dehydrated + postexercise fluid bolus (BOL). In all trials, a 60 mg dose of PSE was administered 30 min before trial and at half time of the STGC. Urinary PSE levels were measured before drug administration and at 90 min postexercise. In addition, body mass (BM) changes and urinary specific gravity (USG), osmolality (OSM), creatinine (Cr), and pH values were recorded. No differences in PSE levels were found 90 min postexercise between conditions (HYD: 208.5 ± 116.5; DHY: 238.9 ± 93.5; BOL: 195.6 ± 107.3 μg · ml(-1)), although large variations were seen within and between participants across conditions (range: 33-475 μg · ml(-1): ICC r = .03-0.16, p > .05). There were no differences between conditions in USG, OSM, pH or PSE/Cr ratio. In conclusion, hydration status did not influence urinary PSE levels after prolonged repeated effort activity, with ~70% of samples greater than the WADA limit (>150 μg · ml(-1)), and ~30% under. Due to the unpredictability of urinary PSE values, athletes should avoid taking any medications containing PSE during competition.

Modeling of wave processes in blocky media with porous and fluid-saturated interlayers

NASA Astrophysics Data System (ADS)

Sadovskii, Vladimir M.; Sadovskaya, Oxana V.; Lukyanov, Alexander A.

2017-09-01

The wave processes in blocky media are analyzed by applying different mathematical models, wherein the elastic blocks interact with each other via pliant interlayers with the complex mechanical properties. Four versions of constitutive equations are considered. In the first version, an elastic interaction between the blocks is simulated within the framework of linear elasticity theory, and the model of elastic-plastic interlayers is constructed to take into account the appearance of irreversible deformation of interlayers at short time intervals. In the second one, the effects of viscoelastic shear in the interblock interlayers are taken into the consideration using the Poynting-Thomson rheological scheme. In the third option, the model of an elastic porous material is used in the interlayers, where the pores collapse if an abrupt compressive stress is applied. In the fourth case, the model of a fluid-saturated material with open pores is examined based on Biot's equations. The collapse of pores is modeled by the generalized rheological approach, wherein the mechanical properties of a material are simulated using four rheological elements. Three of them are the traditional elastic, viscous and plastic elements, the fourth element is the so-called rigid contact, which is used to describe the behavior of materials with the different resistance to tension and compression. It was shown that the thermodynamically consistent model is provided, which means that the energy balance equation is fulfilled for an entire blocky structure, where the kinetic and potential energy of the system is the sum of the kinetic and potential energies of the blocks and interlayers. Under numerical implementation of the interlayers models, the dissipationless finite difference Ivanov's method was used. The splitting method by spatial variables in the combination with the Godunov gap decay scheme was applied in the blocks. As a result, robust and stable computational algorithms are built and tested. Using MPI technology, the parallel software was designed for the modeling of wave processes in 2D setting. The numerical results are presented, discussed and future studies are outlined.

Interlayer utilization (including metal borides) for subsequent deposition of NSD films via microwave plasma CVD on 316 and 440C stainless steels

NASA Astrophysics Data System (ADS)

Ballinger, Jared

Diamond thin films have promising applications in numerous fields due to the extreme properties of diamonds in conjunction with the surface enhancement of thin films. Biomedical applications are numerous including temporary implants and various dental and surgical instruments. The unique combination of properties offered by nanostructured diamond films that make it such an attractive surface coating include extreme hardness, low obtainable surface roughness, excellent thermal conductivity, and chemical inertness. Regrettably, numerous problems exist when attempting to coat stainless steel with diamond generating a readily delaminated film: outward diffusion of iron to the surface, inward diffusion of carbon limiting necessary surface carbon precursor, and the mismatch between the coefficients of thermal expansion yielding substantial residual stress. While some exotic methods have been attempted to overcome these hindrances, the most common approach is the use of an intermediate layer between the stainless steel substrate and the diamond thin film. In this research, both 316 stainless steel disks and 440C stainless steel ball bearings were tested with interlayers including discrete coatings and graded, diffusion-based surface enhancements. Titanium nitride and thermochemical diffusion boride interlayers were both examined for their effectiveness at allowing for the growth of continuous and adherent diamond films. Titanium nitride interlayers were deposited by cathodic arc vacuum deposition on 440C bearings. Lower temperature diamond processing resulted in improved surface coverage after cooling, but ultimately, both continuity and adhesion of the nanostructured diamond films were unacceptable. The ability to grow quality diamond films on TiN interlayers is in agreement with previous work on iron and low alloy steel substrates, and the similarly seen inadequate adhesion strength is partially a consequence of the lacking establishment of an interfacial carbide phase. Surface boriding was implemented using the novel method of microwave plasma CVD with a mixture of hydrogen and diborane gases. On 440C bearings, dual phase boride layers of Fe2B and FeB were formed which supported adhered nanostructured diamond films. Continuity of the films was not seamless with limited regions remaining uncoated potentially corresponding to delamination of the film as evidenced by the presence of tubular structures presumably composed of sp2 bonded carbon. Surface boriding of 316 stainless steel discs was conducted at various powers and pressures to achieve temperatures ranging from 550-800 °C. The substrate boriding temperature was found to substantially influence the resultant interlayer by altering the metal boride(s) present. The lowest temperatures produced an interlayer where CrB was the single detected phase, higher temperatures yielded the presence of only Fe2B, and a combination of the two phases resulted from an intermediate boriding temperature. Compared with the more common, commercialized boriding methods, this a profound result given the problems posed by the FeB phase in addition to other advantages offered by CVD processes and microwave generated plasmas in general. Indentation testing of the boride layers revealed excellent adhesion strength for all borided interlayers, and above all, no evidence of cracking was observed for a sole Fe2B phase. As with boriding of 440C bearings, subsequent diamond deposition was achieved on these interlayers with substantially improved adhesion strength relative to diamond coated TiN interlayers. Both XRD and Raman spectroscopy confirmed a nanostructured diamond film with interfacial chromium carbides responsible for enhanced adhesion strength. Interlayers consisting solely of Fe2B have displayed an ability to support fully continuous nanostructured diamond films, yet additional study is required for consistent reproduction. This is in good agreement with initial work on pack borided high alloy steels to promote diamond film surface modification. The future direction for continued research of nanostructured diamond coatings on microwave plasma CVD borided stainless steel should further investigate the adhesion of both borided interlayers and subsequent NSD films in addition to short, interrupted diamond depositions to study the interlayer/diamond film interface.

A new educational tool to learn about hydration: taste workshops for children.

PubMed

Valero Gaspar, Teresa; Rodríguez-Alonso, Paula; Ruiz Moreno, Emma; Del Pozo de la Calle, Susana; Ávila Torres, José Manuel; Varela Moreiras, Gregorio

2016-07-13

Nutrition education contributes to children´s understanding and practice of healthy lifestyles behaviors. Having a well hydration status is an essential topic, especially since children are a vulnerable population who are much more  prone to dehydration than adults are. The approval of the Report on the European Gastronomic Heritage: Cultural and Educational Aspects in 2014 served as starting point to work on innovative audio-visual and multimedia materials for children. The Spanish Nutrition Foundation (FEN) and the Royal Academy of Gastronomy (RAG), in collaboration with the Ministry of Education, Culture and Sport in Spain (MECD),  developed educational videos for schoolchildren to learn about food, nutrition and gastronomy, specially, the importance of being hydrated. To develop a serial of videos for children between 3 and 9 years old with nutrition and cooking lessons to be used as educational resources in the official curricula. Fourteen chapters related to food, nutrition, gastronomy, physical activity and hydration to be used to record videos were designed and tested. A nutritionist, a chef and two puppets were the main characters acting in the videos.  The chapters were assembled in nine videos that included five sections: introduction, video lesson, recipes -in case of hydration, recipes with different water content foods were recorded-, what have you learntand check your knowledge. A summary of the new educational material was officially presented at the Spain Pavilion during the Expo Milano 2015. Moreover, they are included as education  tool for teachers in the new PANGEI Programme (Food, Nutrition and Gastronomy for Infantile Education) conjointly launched by FEN, RAG and MEDC. Taste workshops are useful as innovative nutrition education tools to reinforce language, listening and motor skills as well as food and nutrition concepts, and specially, the importance of being well hydrated.

Physical activity, hydration and health.

PubMed

Marcos, Ascensión; Manonelles, Pedro; Palacios, Nieves; Wärnberg, Julia; Casajús, José A; Pérez, Margarita; Aznar, Susana; Benito, Pedro J; Martínez-Gomez, David; Ortega, Francisco B; Ortega, Eduardo; Urrialde, Rafael

2014-06-01

Since the beginning of mankind, man has sought ways to promote and preserve health as well as to prevent disease. Hydration, physical activity and exercise are key factors for enhancing human health. However, either a little dose of them or an excess can be harmful for health maintenance at any age. Water is an essential nutrient for human body and a major key to survival has been to prevent dehydration. However, there is still a general controversy regarding the necessary amount to drink water or other beverages to properly get an adequate level of hydration. In addition, up to now the tools used to measure hydration are controversial. To this end, there are several important groups of variables to take into account such as water balance, hydration biomarkers and total body water. A combination of methods will be the most preferred tool to find out any risk or situation of dehydration at any age range. On the other hand, physical activity and exercise are being demonstrated to promote health, avoiding or reducing health problems, vascular and inflammatory disea ses and helping weight management. Therefore, physical activity is also being used as a pill within a therapy to promote health and reduce risk diseases, but as in the case of drugs, dose, intensity, frequency, duration and precautions have to be evaluated and taken into account in order to get the maximum effectiveness and success of a treatment. On the other hand, sedentariness is the opposite concept to physical activity that has been recently recognized as an important factor of lifestyle involved in the obesogenic environment and consequently in the risk of the non-communicable diseases. In view of the literature consulted and taking into account the expertise of the authors, in this review a Decalogue of global recommendations is included to achieve an adequate hydration and physical activity status to avoid overweight/obesity consequences. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Effect of capping layer on interlayer coupling in synthetic spin valves

NASA Astrophysics Data System (ADS)

Li, Kebin; Qiu, Jinjun; Han, Guchang; Guo, Zaibing; Zheng, Yuankai; Wu, Yihong; Li, Jinshan

2005-01-01

The magnetic and transport properties of high quality synthetic spin-valves with the structure of Ta/NiFe/IrMn/CoFe/Ru/CoFe/NOL/CoFe/Cu/CoFe/CL were studied by using magnetoresistance measurements. Here Ti, Hf, and Al are used as the capping layer. It is found that both the thickness and materials properties of the capping layers can affect the interlayer coupling field. The interlayer coupling field oscillates weakly with respect to the thickness of the Ti and Hf capping layers. Extremely strong ferromagnetic coupling has been observed when the thickness of the Al capping layer is in a certain range where resonant exchange coupling takes place. The strength of the interlayer coupling is inversely proportional to the square of the thickness of the spacer. It is a typical characteristic of quantum size effect.

Ultrafast Interlayer Electron Transfer in Incommensurate Transition Metal Dichalcogenide Homobilayers.

PubMed

Li, Yuanyuan; Cui, Qiannan; Ceballos, Frank; Lane, Samuel D; Qi, Zeming; Zhao, Hui

2017-11-08

Two-dimensional materials, such as graphene, transition metal dichalcogenides, and phosphorene, can be used to construct van der Waals multilayer structures. This approach has shown potentials to produce new materials that combine novel properties of the participating individual layers. One key requirement for effectively harnessing emergent properties of these materials is electronic connection of the involved atomic layers through efficient interlayer charge or energy transfer. Recently, ultrafast charge transfer on a time scale shorter than 100 fs has been observed in several van der Waals bilayer heterostructures formed by two different materials. However, information on the transfer between two atomic layers of the same type is rare. Because these homobilayers are essential elements in constructing multilayer structures with desired optoelectronic properties, efficient interlayer transfer is highly desired. Here we show that electron transfer between two monolayers of MoSe 2 occurs on a picosecond time scale. Even faster transfer was observed in homobilayers of WS 2 and WSe 2 . The samples were fabricated by manually stacking two exfoliated monolayer flakes. By adding a graphene layer as a fast carrier recombination channel for one of the two monolayers, the transfer of the photoexcited carriers from the populated to the drained monolayers was time-resolved by femtosecond transient absorption measurements. The observed efficient interlayer carrier transfer indicates that such homobilayers can be used in van der Waals multilayers to enhance their optical absorption without significantly compromising the interlayer transport performance. Our results also provide valuable information for understanding interlayer charge transfer in heterostructures.

Interlayer Interactions in Twisted WSe 2/WS 2 Bilayer Heterojunctions: Synthesis, Characterization, and Modeling

DOE PAGES

Wang, Kai; Huang, Bing; Tian, Mengkun; ...

2016-06-16

Twisting adjacent layers in van der Waals solids can significantly alter their interlayer interactions for tunable optical and electronic properties. Here, we report theoretical calculations, fabrication, and detailed characterizations of WSe 2/WS 2 bilayer heterojunctions with various twist angles that were synthesized by artificially stacking monolayers of CVD-grown WS 2 and WSe 2. Density functional calculations predicted the formation of type-II heterojunctions for the stamped bilayers, with band structures that strongly depend on the interlayer twist angle. Raman spectroscopy reveals strong interlayer coupling with the appearance of a layer-number sensitive mode of WS 2 at 311 cm -1 in WSemore » 2/WS 2 bilayers. This strong interlayer coupling resulted in a 1~2 order of magnitude quenching of the photoluminescence. The broadening and shifts were observed in micro-absorption spectroscopy of WSe 2/WS 2 bilayers, which resulted in a net ~10% enhancement in integrated absorption strength across the visible spectrum with respect to the sum of the individual monolayer spectra. The observed 24 4 meV broadening of the WSe 2 A-exciton absorption band in the bilayers provided an estimate on the rate of charge transfer between the layers that ranged from 23 to 33 fs, and was supported by direct femtosecond pump-probe measurements. These results indicate that interlayer exciton formation and non-radiative decay channels dominate optical properties in these bilayers, which may be important for tunable future photovoltaics and detector applications.« less

Body fluid volume and nutritional status in hemodialysis: vector bioelectric impedance analysis.

PubMed

Espinosa Cuevas, M A; Navarrete Rodriguez, G; Villeda Martinez, M E; Atilano Carsi, X; Miranda Alatriste, P; Tostado Gutiérrez, T; Correa-Rotter, R

2010-04-01

Protein-energy malnutrition and hypervolemia are major causes of morbidity and mortality in patients on chronic hemodialysis (CHD). The methods used to evaluate nutritional status and volume status remain controversial. Vector bioelectric impedance analysis (vector- BIA) has recently been developed to assess both nutritional status and tissue hydration. The purpose of the study was to assess the nutritional status and volume status of patients on CHD with conventional nutritional assessment methods and with vector-BIA and then to compare the resulting findings. 76 Mexican patients on CHD were studied. Nutritional status and body composition were assessed with anthropometry, biochemical variables, and the modified Bilbrey nutritional index (mBNI), the results were compared with both conventional BIA and vector-BIA. The BNI was used to determine the number of patients with normal nutritional status (n = 27, 35.5%), and mild (n = 31, 40.8%), moderate (n = 10, 13.2%) and severe malnutrition (n = 8, 10.5%). Patients displayed shorter vectors with smaller phase angles or with an overhydration vectorial pattern before the initiation of their hemodialysis session. There was general improvement to normal hydration status post-dialysis (p < 0.05); however, 28% remained overhydrated as assessed by vector-BIA. The vector-BIA results showed that worse malnutrition status was associated with greater volume overload (p < 0.05). Diabetes mellitus (DM) was associated with shorter vectors with smaller phase angles (a vectorial pattern of overhydration and cachexia) (p < 0.05). Patients with lower serum creatinine presented with shorter vectors and smaller phase angles (vectorial patterns of malnutrition and/or overhydration) (p < 0.05). In women, lower serum albumin (< 3.4 g/dl) correlated with greater overhydration and malnutrition (p < 0.05). In this population, the vector-BIA showed that 28% of the population remained overhydrated after their hemodialysis session. Diabetics and those with moderate or severe malnutrition were more overhydrated, which is a condition that may be associated with increased cardiovascular morbidity. Because nutritional and volume status are important factors associated with morbidity and mortality in CHD patients, we focused on optimizing the use of existing methods. Our studies suggest that vector-BIA offers a comprehensive and reliable reproducible means of assessing both volume and masses at the bedside and can complement the traditional methods.

Evaluation of nutritional status and energy expenditure in athletes.

PubMed

Mielgo-Ayuso, Juan; Maroto-Sánchez, Beatriz; Luzardo-Socorro, Raquel; Palacios, Gonzalo; Palacios Gil-Antuñano, Nieves; González-Gross, Marcela

2015-02-26

Continuous physical exercise leads the athlete to maintain an unstable balance between dietary intake, energy expenditure and the additional demands of a high amount of physical activity. Thus, an accurate assessment of nutritional status is essential to optimize the performance, since it affects health, body composition, and the recovery of the athlete. Specific aspects like the type of sport, specialty or playing position, training schedule and competition calendar, category, specific objectives, which differ from the general population, must be considered. A biochemical assessment can give us a general idea of the nutritional status, lipid profile, liver or kidney function, if diet is too high in proteins or fats, as well as possible nutritional deficiencies and the need for supplementation. Sport kinanthropometry has great utility that enables the assessment of body mass, height, length, diameter, perimeter and skinfolds, where information is processed by applying different equations, obtaining information on somatotype, body composition, and the proportionality of different parts of the body. To give proper nutritional counselling, energy needs of the athlete must be known. If objective measurement is not possible, there are tables including theoretically established energy requirements of different sports. Dietary assessment should include information about food consumption and nutrient intake to establish the relationship between diet, health status and athlete's performance. On the other hand, an adequate hydration status in athletes is essential to maintain adequate performance. Hence, the knowledge of fluid intake by the athlete is a matter of the utmost importance. Dehydration can cause harmful effects on athletes' health. As there is no gold standard, urine gravidity and urine colour are the most extended methods for analyzing hydration status. There is consensus that due to complexity, the combination of different methods assures an effective data collection which will be useful to proceed in dietary and nutritional intervention.. Copyright AULA MEDICA EDICIONES 2015. Published by AULA MEDICA. All rights reserved.

Relationship between Autonomic Markers of Heart Rate and Subjective Indicators of Recovery Status in Male, Elite Badminton Players.

PubMed

Bisschoff, Christo A; Coetzee, Ben; Esco, Michael R

2016-12-01

The primary aim of the study was to determine if heart rate variability (HRV), and heart rate recovery (HRR) are related to several subjective indicators of recovery status (muscle soreness, hydration status, sleep quality and quantity as well as pre-competition mood states) for different match periods in male, elite, African, singles badminton players. HRV and HRR were measured in twenty-two badminton players before (pre-match), during (in-match), after (post-match) and during rest periods (in-match rest) of 46 national and international matches. Muscle soreness, hydration status, and sleep quality and quantity were measured on a daily basis whereas mood states were measured just before each match via questionnaires. Prior to each match warm-up, players were fitted with a Fix Polar Heart Rate Transmitter Belt to record heart rate every second during each match and HRR during service breaks and after matches. Kubios HRV software was used for final HRV analyses from the series of R-R-intervals. A strong, significant canonical correlation (Rc = 0.96, p = 0.014) was found between HRV, HRR and subjective indicators of recovery status for the in-match period, but only strong, non-significant relationships were observed for pre-match (Rc = 0.98, p = 0.626) and post-match periods (Rc = 0.98, p = 0.085) and a low non-significant relationship (Rc = 0.69, p = 0.258) for the in-match rest period. Canonical functions accounted for between 47.89% and 96.43% of the total variation between the two canonical variants. Results further revealed that Ln-HFnu, the energy index and vigour were the most prominent variables in the relationship between the autonomic markers of heart rate and recovery-related variables. In conclusion, this study proved that subjective indicators of recovery status influence HRV and HRR measures obtained in a competitive badminton environment and should therefore be incorporated in protocols that evaluate these ANS-related parameters.

Electric-field switching of two-dimensional van der Waals magnets

NASA Astrophysics Data System (ADS)

Jiang, Shengwei; Shan, Jie; Mak, Kin Fai

2018-05-01

Controlling magnetism by purely electrical means is a key challenge to better information technology1. A variety of material systems, including ferromagnetic (FM) metals2-4, FM semiconductors5, multiferroics6-8 and magnetoelectric (ME) materials9,10, have been explored for the electric-field control of magnetism. The recent discovery of two-dimensional (2D) van der Waals magnets11,12 has opened a new door for the electrical control of magnetism at the nanometre scale through a van der Waals heterostructure device platform13. Here we demonstrate the control of magnetism in bilayer CrI3, an antiferromagnetic (AFM) semiconductor in its ground state12, by the application of small gate voltages in field-effect devices and the detection of magnetization using magnetic circular dichroism (MCD) microscopy. The applied electric field creates an interlayer potential difference, which results in a large linear ME effect, whose sign depends on the interlayer AFM order. We also achieve a complete and reversible electrical switching between the interlayer AFM and FM states in the vicinity of the interlayer spin-flip transition. The effect originates from the electric-field dependence of the interlayer exchange bias.

Enabling Colloidal Synthesis of Edge-Oriented MoS2 with Expanded Interlayer Spacing for Enhanced HER Catalysis.

PubMed

Sun, Yugang; Alimohammadi, Farbod; Zhang, Dongtang; Guo, Guangsheng

2017-03-08

By selectively promoting heterogeneous nucleation/growth of MoS 2 on graphene monolayer sheets, edge-oriented (EO) MoS 2 nanosheets with expanded interlayer spacing (∼9.4 Å) supported on reduced graphene oxide (rGO) sheets were successfully synthesized through colloidal chemistry, showing the promise in low-cost and large-scale production. The number and edge length of MoS 2 nanosheets per area of graphene sheets were tuned by controlling the reaction time in the microwave-assisted solvothermal reduction of ammonium tetrathiomolybdate [(NH 4 ) 2 MoS 4 ] in dimethylformamide. The edge-oriented and interlayer-expanded (EO&IE) MoS 2 /rGO exhibited significantly improved catalytic activity toward hydrogen evolution reaction (HER) in terms of larger current density, lower Tafel slope, and lower charge transfer resistance compared to the corresponding interlayer-expanded MoS 2 sheets without edge-oriented geometry, highlighting the importance of synergistic effect between edge-oriented geometry and interlayer expansion on determining HER activity of MoS 2 nanosheets. Quantitative analysis clearly shows the linear dependence of current density on the edge length of MoS 2 nanosheets.

Development of a new multi-layer insulation blanket with non-interlayer-contact spacer for space cryogenic mission

NASA Astrophysics Data System (ADS)

Miyakita, Takeshi; Hatakenaka, Ryuta; Sugita, Hiroyuki; Saitoh, Masanori; Hirai, Tomoyuki

2014-11-01

For conventional Multi-Layer Insulation (MLI) blankets, it is difficult to control the layer density and the thermal insulation performance degrades due to the increase in conductive heat leak through interlayer contacts. At low temperatures, the proportion of conductive heat transfer through MLI blankets is large compared to that of radiative heat transfer, hence the decline in thermal insulation performance is significant. A new type of MLI blanket using new spacers; the Non-Interlayer-Contact Spacer MLI (NICS MLI) has been developed. This new MLI blanket uses small discrete spacers and can exclude uncertain interlayer contact between films. It is made of polyetheretherketone (PEEK) making it suitable for space use. The cross-sectional area to length ratio of the spacer is 1.0 × 10-5 m with a 10 mm diameter and 4 mm height. The insulation performance is measured with a boil-off calorimeter. Because the NICS MLI blanket can exclude uncertain interlayer contact, the test results showed good agreement with estimations. Furthermore, the NICS MLI blanket shows significantly good insulation performance (effective emissivity is 0.0046 at ordinary temperature), particularly at low temperatures, due to the high thermal resistance of this spacer.

Use of nonwoven geotextiles as interlayers in concrete pavement systems.

DOT National Transportation Integrated Search

2009-05-01

This document describes the potential use of nonwoven geotextile materials as interlayers in concrete pavement systems, particularly unbonded overlays, in the United States. It briefly discusses Germanys experience, availability and cost of nonwov...

Nonequilibrium Interlayer Transport in Pulsed Laser Deposition

NASA Astrophysics Data System (ADS)

Tischler, J. Z.; Eres, Gyula; Larson, B. C.; Rouleau, Christopher M.; Zschack, P.; Lowndes, Douglas H.

2006-06-01

We use time-resolved surface x-ray diffraction measurements with microsecond range resolution to study the growth kinetics of pulsed laser deposited SrTiO3. Time-dependent surface coverages corresponding to single laser shots were determined directly from crystal truncation rod intensity transients. Analysis of surface coverage evolution shows that extremely fast nonequilibrium interlayer transport, which occurs concurrently with the arrival of the laser plume, dominates the deposition process. A much smaller fraction of material, which is governed by the dwell time between successive laser shots, is transferred by slow, thermally driven interlayer transport processes.

Nickel oxide electrode interlayer in CH3 NH3 PbI3 perovskite/PCBM planar-heterojunction hybrid solar cells.

PubMed

Jeng, Jun-Yuan; Chen, Kuo-Cheng; Chiang, Tsung-Yu; Lin, Pei-Ying; Tsai, Tzung-Da; Chang, Yun-Chorng; Guo, Tzung-Fang; Chen, Peter; Wen, Ten-Chin; Hsu, Yao-Jane

2014-06-25

This study successfully demonstrates the application of inorganic p-type nickel oxide (NiOx ) as electrode interlayer for the fabrication of NiOx /CH3 NH3 PbI3 perovskite/PCBM PHJ hybrid solar cells with a respectable solar-to-electrical PCE of 7.8%. The better energy level alignment and improved wetting of the NiOx electrode interlayer significantly enhance the overall photovoltaic performance. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Triple Iron Triathlon Leads to a Decrease in Total Body Mass but Not to Dehydration

ERIC Educational Resources Information Center

Knechtle, Beat; Knechtle, Patrizia; Rosemann, Thomas; Oliver, Senn

2010-01-01

A loss in total body mass during an ultraendurance performance is usually attributed to dehydration. We identified the changes in total body mass, fat mass, skeletal muscle mass, and selected markers of hydration status in 31 male nonprofessional ultratriathletes participating in a Triple Iron triathlon involving 11.4 km swimming, 540 km cycling…

Physiological and Selective Attention Demands during an International Rally Motor Sport Event

PubMed Central

Turner, Anthony P.; Richards, Hugh

2015-01-01

Purpose. To monitor physiological and attention responses of drivers and codrivers during a World Rally Championship (WRC) event. Methods. Observational data were collected from ten male drivers/codrivers on heart rate (HR), core body (T core) and skin temperature (T sk), hydration status (urine osmolality), fluid intake (self-report), and visual and auditory selective attention (performance tests). Measures were taken pre-, mid-, and postcompetition day and also during the precompetition reconnaissance. Results. In ambient temperatures of 20.1°C (in-car peak 33.9°C) mean (SD) peak HR and T core were significantly elevated (P < 0.05) during rally compared to reconnaissance (166 (17) versus 111 (16) beats·min−1 and 38.5 (0.4) versus 37.6 (0.2)°C, resp.). Values during competitive stages were substantially higher in drivers. High urine osmolality was indicated in some drivers within competition. Attention was maintained during the event but was significantly lower prerally, though with considerable individual variation. Conclusions. Environmental and physical demands during rally competition produced significant physiological responses. Challenges to thermoregulation, hydration status, and cognitive function need to be addressed to minimise potentially negative effects on performance and safety. PMID:25866799

Physiological and selective attention demands during an international rally motor sport event.

PubMed

Turner, Anthony P; Richards, Hugh

2015-01-01

To monitor physiological and attention responses of drivers and codrivers during a World Rally Championship (WRC) event. Observational data were collected from ten male drivers/codrivers on heart rate (HR), core body (T core) and skin temperature (T sk), hydration status (urine osmolality), fluid intake (self-report), and visual and auditory selective attention (performance tests). Measures were taken pre-, mid-, and postcompetition day and also during the precompetition reconnaissance. In ambient temperatures of 20.1°C (in-car peak 33.9°C) mean (SD) peak HR and T core were significantly elevated (P < 0.05) during rally compared to reconnaissance (166 (17) versus 111 (16) beats · min(-1) and 38.5 (0.4) versus 37.6 (0.2)°C, resp.). Values during competitive stages were substantially higher in drivers. High urine osmolality was indicated in some drivers within competition. Attention was maintained during the event but was significantly lower prerally, though with considerable individual variation. Environmental and physical demands during rally competition produced significant physiological responses. Challenges to thermoregulation, hydration status, and cognitive function need to be addressed to minimise potentially negative effects on performance and safety.

Conjugated Polymer Zwitterions: Efficient Interlayer Materials in Organic Electronics.

PubMed

Liu, Yao; Duzhko, Volodimyr V; Page, Zachariah A; Emrick, Todd; Russell, Thomas P

2016-11-15

Conjugated polymer zwitterions (CPZs) are neutral, hydrophilic, polymer semiconductors. The pendent zwitterions, viewed as side chain dipoles, impart solubility in polar solvents for solution processing, and open opportunities as interfacial components of optoelectronic devices, for example, between metal electrodes and organic semiconductor active layers. Such interlayers are crucial for defining the performance of organic electronic devices, e.g., field-effect transistors (OFETs), light-emitting diodes (OLEDs), and photovoltaics (OPVs), all of which consist of multilayer structures. The interlayers reduce the Schottky barrier height and thus improve charge injection in OFETs and OLEDs. In OPVs, the interlayers serve to increase the built-in electric potential difference (V bi ) across the active layer, ensuring efficient extraction of photogenerated charge carriers. In general, polar and even charged electronically active polymers have gained recognition for their ability to modify metal/semiconductor interfaces to the benefit of organic electronics. While conjugated polyelectrolytes (CPEs) as interlayer materials are well-documented, open questions remain about the role of mobile counterions in CPE-containing devices. CPZs possess the processing advantages of CPEs, but as neutral molecules lack any potential complications associated with counterions. The electronic implications of CPZs on metal electrodes stem from the orientation of the zwitterion dipole moment in close proximity to the metal surface, and the resultant surface-induced polarization. This generates an interfacial dipole (Δ) at the CPZ/metal interface, altering the work function of the electrode, as confirmed by ultraviolet photoelectron spectroscopy (UPS), and improving device performance. An ideal cathode interlayer would reduce electrode work function, have orthogonal processability to the active layer, exhibit good film forming properties (i.e., wettability/uniformity), prevent exciton quenching, possess optimal electron affinity that neither limits the work function reduction nor impedes the charge extraction, transport electrons selectively, and exhibit long-term stability. Our recent discoveries show that CPZs achieve many of these attributes, and are poised for further expansion and development in the interfacial science of organic electronics. This Account reviews a recent collaboration that began with the synthesis of CPZs and a study of their structural and electronic properties on metals, then extended to their application as interlayer materials for OPVs. We discuss CPZ structure-property relationships based on several material platforms, ranging from homopolymers to copolymers, and from materials with intrinsic p-type conjugated backbones to those with intrinsic n-type conjugated backbones. We discuss key components of such interlayers, including (i) the origin of work function reduction of CPZ interlayers on metals; (ii) the role of the frontier molecular orbital energy levels and their trade-offs in optimizing electronic and device properties; and (iii) the role of polymer conductivity type and the magnitude of charge carrier mobility. Our motivation is to present our prior use and current understanding of CPZs as interlayer materials in organic electronics, and describe outstanding issues and future potential directions.

Low-Frequency Interlayer Raman Modes to Probe Interface of Twisted Bilayer MoS 2

DOE PAGES

Huang, Shengxi; Liang, Liangbo; Ling, Xi; ...

2016-02-21

A variety of van der Waals homo- and hetero- structures assembled by stamping monolayers together present optoelectronic properties suitable for diverse applications. Understanding the details of the interlayer stacking and resulting coupling is crucial for tuning these properties. Twisted bilayer transition metal dichalcogenides offer a great platform for developing a precise understanding of the structure/property relationship. Here, we study the low-frequency interlayer shear and breathing Raman modes (<50 cm-1) in twisted bilayer MoS 2 by Raman spectroscopy and first-principles modeling. Twisting introduces both rotational and translational shifts and significantly alters the interlayer stacking and coupling, leading to notable frequency andmore » intensity changes of low-frequency modes. The frequency variation can be up to 8 cm-1 and the intensity can vary by a factor of ~5 for twisting near 0 and 60 , where the stacking is a mixture of multiple high-symmetry stacking patterns and is thus especially sensitive to twisting. Moreover, for twisting angles between 20 and 40 , the interlayer coupling is nearly constant since the stacking results in mismatched lattices over the entire sample. It follows that the Raman signature is relatively uniform. Interestingly, unlike the breathing mode, the shear mode is extremely sensitive to twisting: it disappears between 20 and 40 as its frequency drops to almost zero due to the stacking-induced mismatch. Note that for some samples, multiple breathing mode peaks appear, indicating non-uniform coupling across the interface. In contrast to the low-frequency interlayer modes, high-frequency intralayer Raman modes are much less sensitive to interlayer stacking and coupling, showing negligible changes upon twisting. Our research demonstrates the effectiveness of low-frequency Raman modes for probing the interfacial coupling and environment of twisted bilayer MoS2, and potentially other two-dimensional materials and heterostructures.« less

In vitro evaluation of diamond-like carbon coatings with a Si/SiC x interlayer on surgical NiTi alloy

NASA Astrophysics Data System (ADS)

Liu, C. L.; Chu, Paul K.; Yang, D. Z.

2007-04-01

Diamond-like carbon (DLC) coatings were produced with a Si/SiCx interlayer by a hybrid plasma immersion ion implantation and deposition process to improve the adhesion between the carbon layer and surgical NiTi alloy substrate. The structure, mechanical properties, corrosion resistance and biocompatibility of the coatings were evaluated in vitro by Raman spectroscopy, pin-on-disk tests, potentiodynamic polarization tests and simulated fluid immersion tests. The DLC coatings with a Si/SiCx interlayer of a suitable thickness have better adhesion, lower friction coefficients and enhanced corrosion resistance. In the simulated body fluid tests, the coatings exhibit effective corrosion protection and good biocompatibility as indicated by PC12 cell cultures. DLC films fabricated on a Si/SiCx interlayer have high potential as protective coatings for biomedical NiTi materials.

Induced nano-scale self-formed metal-oxide interlayer in amorphous silicon tin oxide thin film transistors.

PubMed

Liu, Xianzhe; Xu, Hua; Ning, Honglong; Lu, Kuankuan; Zhang, Hongke; Zhang, Xiaochen; Yao, Rihui; Fang, Zhiqiang; Lu, Xubing; Peng, Junbiao

2018-03-07

Amorphous Silicon-Tin-Oxide thin film transistors (a-STO TFTs) with Mo source/drain electrodes were fabricated. The introduction of a ~8 nm MoO x interlayer between Mo electrodes and a-STO improved the electron injection in a-STO TFT. Mo adjacent to the a-STO semiconductor mainly gets oxygen atoms from the oxygen-rich surface of a-STO film to form MoO x interlayer. The self-formed MoO x interlayer acting as an efficient interface modification layer could conduce to the stepwise internal transport barrier formation while blocking Mo atoms diffuse into a-STO layer, which would contribute to the formation of ohmic contact between Mo and a-STO film. It can effectively improve device performance, reduce cost and save energy for the realization of large-area display with high resolution in future.

Effect of Pd Interlayer on Electrochemical Properties of ENIG Surface Finish in 3.5 wt.% NaCl Solution

NASA Astrophysics Data System (ADS)

Nam, N. D.; Bui, Q. V.; Nhan, H. T.; Phuong, D. V.; Bian, M. Z.

2014-09-01

The corrosion resistance of a multilayered (NiP-Pd-Au) coating with various thicknesses of palladium (Pd) interlayer deposited on copper by an electroless method was investigated using electrochemical techniques including potentiodynamic polarization and electrochemical impedance spectroscopy. In addition, the surface finish was examined by x-ray diffraction analysis and scanning electron microscopy, and the contact angle of the liquid-solid interface was recorded. The corrosion resistance of the copper substrate was considerably improved by Pd interlayer addition. Increase of the thickness of the Pd interlayer enhanced the performance of the Cu-NiP-Pd-Au coating due to low porosity, high protective efficiency, high charge-transfer resistance, and contact angle. These are attributed to the diffusion of layers in the Cu-NiP-Pd-Au coating acting as a physical barrier layer, leading to the protection provided by the coating.

Aminopropyl-modified magnesium-phyllosilicates: layered solids with tailored interlayer access and reactivity.

PubMed

Ferreira, Ricardo B; da Silva, César R; Pastore, Heloise O

2008-12-16

Despite its wide application, the synthesis of aminopropyl-modified magnesium-phyllosilicates was known only in the case where every silicon atom bore an organic pending group. This paper shows the preparation of aminopropyl-modified talc where tailored amounts of silicon atoms are bound to an aminopropyl group. The decrease in the concentration of the organoamino group leaves a proportional concentration of interlayer SiOH groups that can be used to react with other silylation agents. The amino group reacts with CO2, forming a carbamate functionality; it seems that the presence of this group avoids delamination in water as performed for the parent compound. Bearing in mind that the aminopropyl group can be changed by other groups, the present synthesis strategy demonstrates ways to produce solids with controlled surface properties with interlayer amino and SiOH groups in variable concentrations, allowing formation of several other interlayer functionalities.

Correlated lateral phase separations in stacks of lipid membranes

NASA Astrophysics Data System (ADS)

Hoshino, Takuma; Komura, Shigeyuki; Andelman, David

2015-12-01

Motivated by the experimental study of Tayebi et al. [Nat. Mater. 11, 1074 (2012)] on phase separation of stacked multi-component lipid bilayers, we propose a model composed of stacked two-dimensional Ising spins. We study both its static and dynamical features using Monte Carlo simulations with Kawasaki spin exchange dynamics that conserves the order parameter. We show that at thermodynamical equilibrium, due to strong inter-layer correlations, the system forms a continuous columnar structure for any finite interaction across adjacent layers. Furthermore, the phase separation shows a faster dynamics as the inter-layer interaction is increased. This temporal behavior is mainly due to an effective deeper temperature quench because of the larger value of the critical temperature, Tc, for larger inter-layer interaction. When the temperature ratio, T/Tc, is kept fixed, the temporal growth exponent does not increase and even slightly decreases as a function of the increased inter-layer interaction.

Au/n-InP Schottky diodes using an Al2O3 interfacial layer grown by atomic layer deposition

NASA Astrophysics Data System (ADS)

Kim, Hogyoung; Kim, Min Soo; Yoon, Seung Yu; Choi, Byung Joon

2017-02-01

We investigated the effect of an Al2O3 interfacial layer grown by atomic layer deposition on the electrical properties of Au Schottky contacts to n-type InP. Considering barrier inhomogeneity, modified Richardson plots yielded a Richardson constant of 8.4 and 7.5 Acm-2K-2, respectively, for the sample with and without the Al2O3 interlayer (theoretical value of 9.4 Acm-2K-2 for n-type InP). The dominant reverse current flow for the sample with an Al2O3 interlayer was found to be Poole-Frenkel emission. From capacitance-voltage measurements, it was observed that the capacitance for the sample without the Al2O3 interlayer was frequency dependent. Sputter-induced defects as well as structural defects were passivated effectively with an Al2O3 interlayer.

Effect of Mg interlayer on perpendicular magnetic anisotropy of CoFeB films in MgO/Mg/CoFeB/Ta structure

NASA Astrophysics Data System (ADS)

Ma, Q. L.; Iihama, S.; Kubota, T.; Zhang, X. M.; Mizukami, S.; Ando, Y.; Miyazaki, T.

2012-09-01

The effects of Mg metallic interlayer on the magnetic properties of thin CoFeB films in MgO/Mg (tMg)/CoFeB (1.2 nm)/Ta structures were studied in this letter. Our experimental result shows that the CoFeB film exhibits perpendicular magnetic anisotropy (PMA) when the CoFeB and MgO layers are separated by a metallic Mg layer with a maximum thickness of 0.8 nm. The origin of PMA was discussed by considering the preferential transmission of the Δ1 symmetry preserved by the Mg interlayer in crystallized MgO/Mg/CoFeB/Ta. In addition, the thin Mg interlayer also contributes to enhancing the thermal stability and reducing the effective damping constant and coercivity of the CoFeB film.

Symmetries and synchronization in multilayer random networks

NASA Astrophysics Data System (ADS)

Saa, Alberto

2018-04-01

In the light of the recently proposed scenario of asymmetry-induced synchronization (AISync), in which dynamical uniformity and consensus in a distributed system would demand certain asymmetries in the underlying network, we investigate here the influence of some regularities in the interlayer connection patterns on the synchronization properties of multilayer random networks. More specifically, by considering a Stuart-Landau model of complex oscillators with random frequencies, we report for multilayer networks a dynamical behavior that could be also classified as a manifestation of AISync. We show, namely, that the presence of certain symmetries in the interlayer connection pattern tends to diminish the synchronization capability of the whole network or, in other words, asymmetries in the interlayer connections would enhance synchronization in such structured networks. Our results might help the understanding not only of the AISync mechanism itself but also its possible role in the determination of the interlayer connection pattern of multilayer and other structured networks with optimal synchronization properties.

PNR studies of spin-flop and spin-flip processes in magnetic multilayer, NiFeCo/Cu system

NASA Astrophysics Data System (ADS)

Ambaye, Hailemariam; Sato, Hideo; Mankey, Gary; Lauter, Valeria; Goyette, Richard

2010-03-01

Early GMR devices relied on antiferromagnetic interlayer coupling to work and it was shown that the interlayer coupling is in fact oscillatory, with both ferromagnetic and antiferromagnetic interlayer exchange depending on the thickness of the nonmagnetic layer [1,2]. Different competing interactions such as magnetic anisotropy and interlayer afm coupling occur in multilayer systems. Distinguishing the individual contributions is one of the major challenges in the study of multilayered systems. We used polarized neutron reflectivity with full polarization analysis to understand how the magnetization is distributed through the system and how deep the flipping process of the magnetization goes into the system. The easy axis field dependence of occurrence of spin-flop and spin-flip events in the system will be reported. [4pt] [1] S. S. P. Parkin, Phys. Rev. Lett. 71, 1641 (1993).[0pt] [2] D. Elefant, et al., Phys. Rev. B 77, 014426 (2008).

Diffusion Bonding of Silicon Carbide for MEMS-LDI Applications

NASA Technical Reports Server (NTRS)

Halbig, Michael C.; Singh, Mrityunjay; Shpargel, Tarah P.; Kiser, J. Douglas

2007-01-01

A robust joining approach is critically needed for a Micro-Electro-Mechanical Systems-Lean Direct Injector (MEMS-LDI) application which requires leak free joints with high temperature mechanical capability. Diffusion bonding is well suited for the MEMS-LDI application. Diffusion bonds were fabricated using titanium interlayers between silicon carbide substrates during hot pressing. The interlayers consisted of either alloyed titanium foil or physically vapor deposited (PVD) titanium coatings. Microscopy shows that well adhered, crack free diffusion bonds are formed under optimal conditions. Under less than optimal conditions, microcracks are present in the bond layer due to the formation of intermetallic phases. Electron microprobe analysis was used to identify the reaction formed phases in the diffusion bond. Various compatibility issues among the phases in the interlayer and substrate are discussed. Also, the effects of temperature, pressure, time, silicon carbide substrate type, and type of titanium interlayer and thickness on the microstructure and composition of joints are discussed.

Superconducting composite with multilayer patterns and multiple buffer layers

DOEpatents

Wu, X.D.; Muenchausen, R.E.

1993-10-12

An article of manufacture is described including a substrate, a patterned interlayer of a material selected from the group consisting of magnesium oxide, barium-titanium oxide or barium-zirconium oxide, the patterned interlayer material overcoated with a secondary interlayer material of yttria-stabilized zirconia or magnesium-aluminum oxide, upon the surface of the substrate whereby an intermediate article with an exposed surface of both the overcoated patterned interlayer and the substrate is formed, a coating of a buffer layer selected from the group consisting of cerium oxide, yttrium oxide, curium oxide, dysprosium oxide, erbium oxide, europium oxide, iron oxide, gadolinium oxide, holmium oxide, indium oxide, lanthanum oxide, manganese oxide, lutetium oxide, neodymium oxide, praseodymium oxide, plutonium oxide, samarium oxide, terbium oxide, thallium oxide, thulium oxide, yttrium oxide and ytterbium oxide over the entire exposed surface of the intermediate article, and, a ceramic superconductor. 5 figures.

Very high S-band microwave absorption of carbon nanotube buckypapers with Mn nanoparticle interlayers

NASA Astrophysics Data System (ADS)

Lu, Shaowei; Bai, Yaoyao; Wang, Jijie; Zhang, Lu; Tian, Caijiao; Ma, Keming; Wang, Xiaoqiang

2018-03-01

Flexible and high-performance electromagnetic absorbing materials of multi-walled carbon nanotube (MWCNT) buckypapers with Mn nanoparticles (NPSs) interlayer were fabricated via monodisperse solutions through layer by layer vacuum filtration method. The morphology and element composition of buckypapers were characterized by scanning electron microscopy, energy dispersive spectrometer, and X-ray diffraction. The formation of flexible MWCNT buckypapers with Mn NPS (0-30 wt. %) interlayer was attributed to nanostructure and morphology of the samples. When the blended Mn NPS content in buckypapers is 20 wt. %, there are evidently two larger absorption peaks (-13.2 dB at 3.41 GHz, -15.6 dB at 3.52 GHz) of the buckypaper with an absorbing thickness of 0.1 mm. The fundamental microwave absorption mechanism of the buckypapers is discussed. This work opens a new pathway towards tuning microwave absorbers performance and this method can be extended to exploit other excellent microwave absorbers with interlayer.

Self-Assembly of Alkylammonium Chains on Montmorillonite: Effect of Interlayer Cations, CEC, and Chain Length

NASA Astrophysics Data System (ADS)

Chen, Hua; Li, Yingjun; Zhou, Yuanlin; Wang, Shanqiang; Zheng, Jian; He, Jiacai

2017-12-01

Recently, polymeric materials have been filled with synthetic or natural inorganic compounds in order to improve their properties. Especially, polymer clay nanocomposites have attracted both academic and industrial attention. Currently, the structure and physical phenomena of organoclays at molecular level are difficultly explained by existing experimental techniques. In this work, molecular dynamics (MD) simulation was executed using the CLAYFF and CHARMM force fields to evaluate the structural properties of organoclay such as basal spacing, interlayer density, energy and the arrangement of alkyl chains in the interlayer spacing. Our results are in good agreement with available experimental or other simulation data. The effects of interlayer cations (Na+, K+, Ca2+), the cation exchange capacity, and the alkyl chain length on the basal spacing and the structural properties are estimated. These simulations are expected to presage the microstructure of organo-montmorillonite and lead relevant engineering applications.

Insights into the interfacial strengthening mechanisms of calcium-silicate-hydrate/polymer nanocomposites.

PubMed

Zhou, Yang; Hou, Dongshuai; Geng, Guoqing; Feng, Pan; Yu, Jiao; Jiang, Jinyang

2018-03-28

The mechanical properties of organic/inorganic composites can be highly dependent on the interfacial interactions. In this work, with organic polymers intercalated into the interlayer of inorganic calcium silicate hydrate (C-S-H), the primary binding phase of Portland cement, great ductility improvement is obtained for the nanocomposites. Employing reactive molecular dynamics, the simulation results indicate that strong interfacial interactions between the polymers and the substrate contribute greatly to strengthening the materials, when C-S-H/poly ethylene glycol (PEG), C-S-H/poly acrylic acid (PAA), and C-S-H/poly vinyl alcohol (PVA) were subject to uniaxial tension along different lattice directions. In the x and z direction tensile processes, the Si-OCa bonds of the C-S-H gel, which were elongated and broken to form Si-OH and Ca-OH, play a critical role in loading resistance, while the incorporation of polymers bridged the neighboring silicate sheets, and activated more the hydrolytic reactions at the interfaces to avoid strain localization, thus increasing the tensile strength and postponing the fracture. On the other hand, Si-O-Si bonds of C-S-H mainly take the load when tension was applied along the y direction. During the post-yield stage, rearrangements of silicate tetrahedra occurred to prevent rapid damage. The polymer intercalation further elongates this post-yield period by forming interfacial Si-O-C bonds, which promote rearrangements and improve the connectivity of the defective silicate morphology, significantly improving the ductility. Among the polymers, PEG exhibits the strongest interaction with C-S-H, and thus C-S-H/PEG possesses the highest ductility. We expect that the molecular-scale mechanisms interpreted here will shed new light on the stress-activated chemical interactions at the organic/inorganic interfaces, and help eliminate the brittleness of cement-based materials on a genetic level.

Structure of nanocrystalline calcium silicate hydrates: insights from X-ray diffraction, synchrotron X-ray absorption and nuclear magnetic resonance.

PubMed

Grangeon, Sylvain; Claret, Francis; Roosz, Cédric; Sato, Tsutomu; Gaboreau, Stéphane; Linard, Yannick

2016-06-01

The structure of nanocrystalline calcium silicate hydrates (C-S-H) having Ca/Si ratios ranging between 0.57 ± 0.05 and 1.47 ± 0.04 was studied using an electron probe micro-analyser, powder X-ray diffraction, 29 Si magic angle spinning NMR, and Fourier-transform infrared and synchrotron X-ray absorption spectroscopies. All samples can be described as nanocrystalline and defective tobermorite. At low Ca/Si ratio, the Si chains are defect free and the Si Q 3 and Q 2 environments account, respectively, for up to 40.2 ± 1.5% and 55.6 ± 3.0% of the total Si, with part of the Q 3 Si being attributable to remnants of the synthesis reactant. As the Ca/Si ratio increases up to 0.87 ± 0.02, the Si Q 3 environment decreases down to 0 and is preferentially replaced by the Q 2 environment, which reaches 87.9 ± 2.0%. At higher ratios, Q 2 decreases down to 32.0 ± 7.6% for Ca/Si = 1.38 ± 0.03 and is replaced by the Q 1 environment, which peaks at 68.1 ± 3.8%. The combination of X-ray diffraction and NMR allowed capturing the depolymerization of Si chains as well as a two-step variation in the layer-to-layer distance. This latter first increases from ∼11.3 Å (for samples having a Ca/Si ratio <∼0.6) up to 12.25 Å at Ca/Si = 0.87 ± 0.02, probably as a result of a weaker layer-to-layer connectivity, and then decreases down to 11 Å when the Ca/Si ratio reaches 1.38 ± 0.03. The decrease in layer-to-layer distance results from the incorporation of interlayer Ca that may form a Ca(OH) 2 -like structure, nanocrystalline and intermixed with C-S-H layers, at high Ca/Si ratios.

Surface and interlayer base-characters in lepidocrocite titanate: The adsorption and intercalation of fatty acid

NASA Astrophysics Data System (ADS)

Maluangnont, Tosapol; Arsa, Pornanan; Limsakul, Kanokporn; Juntarachairot, Songsit; Sangsan, Saithong; Gotoh, Kazuma; Sooknoi, Tawan

2016-06-01

While layered double hydroxides (LDHs) with positively-charged sheets are well known as basic materials, layered metal oxides having negatively-charged sheets are not generally recognized so. In this article, the surface and interlayer base-characters of O2- sites in layered metal oxides have been demonstrated, taking lepidocrocite titanate K0.8Zn0.4Ti1.6O4 as an example. The low basicity (0.04 mmol CO2/g) and low desorption temperature (50-300 °C) shown by CO2- TPD suggests that O2- sites at the external surfaces is weakly basic, while those at the interlayer space are mostly inaccessible to CO2. The liquid-phase adsorption study, however, revealed the uptake as much as 37% by mass of the bulky palmitic acid (C16 acid). The accompanying expansion of the interlayer space by ~0.1 nm was detected by PXRD and TEM. In an opposite manner to the external surfaces, the interlayer O2- sites can deprotonate palmitic acid, forming the salt (i.e., potassium palmitate) occluded between the sheets. Two types of basic sites are proposed based on ultrafast 1H MAS NMR and FTIR results. The interlayer basic sites in lepidocrocite titanate leads to an application of this material as a selective and stable two-dimensional (2D) basic catalyst, as demonstrated by the ketonization of palmitic acid into palmitone (C31 ketone). Tuning of the catalytic activity by varying the type of metal (Zn, Mg, and Li) substituting at TiIV sites was also illustrated.

Intercalation of paracetamol into the hydrotalcite-like host

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kovanda, Frantisek, E-mail: Frantisek.Kovanda@vscht.cz; Maryskova, Zuzana; Kovar, Petr

2011-12-15

Hydrotalcite-like compounds are often used as host structures for intercalation of various anionic species. The product intercalated with the nonionic, water-soluble pharmaceuticals paracetamol, N-(4-hydroxyphenyl)acetamide, was prepared by rehydration of the Mg-Al mixed oxide obtained by calcination of hydrotalcite-like precursor at 500 Degree-Sign C. The successful intercalation of paracetamol molecules into the interlayer space was confirmed by powder X-ray diffraction and infrared spectroscopy measurements. Molecular simulations showed that the phenolic hydroxyl groups of paracetamol interact with hydroxide sheets of the host via the hydroxyl groups of the positively charged sites of Al-containing octahedra; the interlayer water molecules are located mostly nearmore » the hydroxide sheets. The arrangement of paracetamol molecules in the interlayer is rather disordered and interactions between neighboring molecules cause their tilting towards the hydroxide sheets. Dissolution tests in various media showed slower release of paracetamol intercalated in the hydrotalcite-like host in comparison with tablets containing the powdered pharmaceuticals. - Graphical abstract: Molecular simulations showed disordered arrangement of paracetamol molecules in the interlayer; most of the interlayer water molecules are located near the hydroxide sheets. Black-Small-Square Highlights: Black-Right-Pointing-Pointer Paracetamol was intercalated in Mg-Al hydrotalcite-like host by rehydration/reconstruction procedure. Black-Right-Pointing-Pointer Paracetamol phenolic groups interact with positively charged sites in hydroxide sheets. Black-Right-Pointing-Pointer Molecular simulations showed disordered arrangement of guest molecules in the interlayer. Black-Right-Pointing-Pointer Slower release of paracetamol intercalated in the hydrotalcite-like host was observed.« less

RBC deformability and amino acid concentrations after hypo-osmotic challenge may reflect chronic cell hydration status in healthy young men

PubMed Central

Stookey, Jodi D; Klein, Alexis; Hamer, Janice; Chi, Christine; Higa, Annie; Ng, Vivian; Arieff, Allen; Kuypers, Frans A; Larkin, Sandra; Perrier, Erica; Lang, Florian

2013-01-01

Biomarkers of chronic cell hydration status are needed to determine whether chronic hyperosmotic stress increases chronic disease risk in population-representative samples. In vitro, cells adapt to chronic hyperosmotic stress by upregulating protein breakdown to counter the osmotic gradient with higher intracellular amino acid concentrations. If cells are subsequently exposed to hypo-osmotic conditions, the adaptation results in excess cell swelling and/or efflux of free amino acids. This study explored whether increased red blood cell (RBC) swelling and/or plasma or urine amino acid concentrations after hypo-osmotic challenge might be informative about relative chronic hyperosmotic stress in free-living men. Five healthy men (20–25 years) with baseline total water intake below 2 L/day participated in an 8-week clinical study: four 2-week periods in a U-shaped A-B-C-A design. Intake of drinking water was increased by +0.8 ± 0.3 L/day in period 2, and +1.5 ± 0.3 L/day in period 3, and returned to baseline intake (0.4 ± 0.2 L/day) in period 4. Each week, fasting blood and urine were collected after a 750 mL bolus of drinking water, following overnight water restriction. The periods of higher water intake were associated with significant decreases in RBC deformability (index of cell swelling), plasma histidine, urine arginine, and urine glutamic acid. After 4 weeks of higher water intake, four out of five participants had ½ maximal RBC deformability below 400 mmol/kg; plasma histidine below 100 μmol/L; and/or undetectable urine arginine and urine glutamic acid concentrations. Work is warranted to pursue RBC deformability and amino acid concentrations after hypo-osmotic challenge as possible biomarkers of chronic cell hydration. PMID:24303184

The interrelationship of research in the laboratory and the field to assess hydration status and determine mechanisms involved in water regulation during physical activity.

PubMed

Stachenfeld, Nina S

2014-05-01

Changes in skin blood and sweating are the primary mechanisms for heat loss in humans. A hot, humid environment concomitant with dehydration limits the ability to increase skin blood flow for the purpose of transferring heat from the body core to skin surface and evaporate sweat to maintain core temperature within safe limits during exercise. Adequate hydration improves thermoregulation by maintaining blood volume to support skin blood flow and sweating. Humans rely on fluid intake to maintain total body water and blood volume, and have developed complex mechanisms to sense changes in the amount and composition of fluid in the body. This paper addresses the interrelationship of research in the laboratory and the field to assess hydration status involved in body water and temperature regulation during exercise. In the controlled setting of a research laboratory, investigators are able to investigate the contributions of volume and tonicity of fluid in the plasma to body water and temperature regulation during exercise and recovery. For example, laboratory studies have shown that tonicity in a rehydration beverage maintains the thirst mechanism (and stimulates drinking), and contributes to the ongoing stimulation of renal fluid retention hormones, ultimately leading to a more complete rehydration. Research in the field cannot control the environment precisely, but these studies provide a natural, 'real-life' setting to study fluid and temperature regulation during exercise. The conditions encountered in the field are closest to the environment during competition, and data collected in the field can have an immediate impact on performance and safety during exercise. There is an important synergy between these two methods of collecting data that support performance and protect athletes from harm during training and improve performance during competition.

Menstrual Changes in Body Composition of Female Athletes.

PubMed

Stachoń, Aleksandra Jadwiga

2016-06-01

The aim of the study was to determine whether the tendencies and scope of changes in body mass, body composition and body girths across the menstrual cycle were similar or different in women of different body build. Anthropometric examinations were carried out in a group of 40 naturally regularly menstruated females practicing team sports (aged 19-21, B-v 169.3+/-6.4 cm, body mass 59.6+/-7.0 kg), in the follicular, periovulatory and luteal phases of the menstrual cycle. The phases were determined on the basis of data from two consecutive menstrual cycles taking into account the cycle’s length. To establish the type of body build, Body Mass Index, hydration status and skinfold thickness were measured. For a statistical analysis, a multiple comparisons with multiple confidence intervals were applied. The increase in body mass between the follicular and the luteal phases was observed in all groups of women, the biggest gain was recorded in slim women, who in the luteal phase weighted 0.8 kg more. The amount of fat mass increased significantly across the menstrual cycle only in more hydrated (by about 0.66 kg) and slim women (by about 0.54 kg). Significant changes between consecutive phases of the menstrual cycle in waist and hip girths, and suprailiac skinfold thickness in some groups of women also indicate influence of fatness and hydration status and slenderness. In view of the presented results, the body build seems important for an analysis of the pattern of each component’s changes across the menstrual cycle, especially for female athletes. Certain changes can be seen only in some groups of women, therefore somatic features can be considered as a predictor of the intensity of changes.

Validity of HydraTrend reagent strips for the assessment of hydration status.

PubMed

Abbey, Bryce M; Heelan, Kate A; Brown, Gregory A; Bartee, Rodrick T

2014-09-01

Hydration is used by athletic governing organizations for weight class eligibility. The measurement of urine specific gravity (USG) as a measure of hydration by reagent strips is a controversial issue. The purpose of this study was to determine the validity of HydraTrend reagent strips that facilitate the correction of USG for alkaline urine samples against refractometry for the assessment of USG. Fifty-one participants (33 males, age = 22.3 ± 1.3 years; 18 females, age = 22.4 ± 1.2 years) provided 84 urine samples. The samples were tested for USG using refractometry and reagent strips and for pH using reagent strips and a digital pH meter. Strong correlation coefficients were found between refractometry and reagent strips for USG (rs(82) = 0.812, p < 0.01) and between reagent strips and pH meter for pH (rs(82) = 0.939, p < 0.01). It was observed that false negative results for National Collegiate Athletic Association (NCAA) requirements (fail refractometry with USG >1.020, pass reagent strips with USG ≤1.020) occurred 39% (33/84) of the time and false negative results for National Federation of State High School Association (NFHS) requirements (fail refractometry with USG >1.025, pass reagent strips with USG ≤1.025) occurred 14% (12/84) of the time. There were no false positives (pass refractometry and fail reagent strips) for NCAA or NFHS requirements. These data show that refractometry and reagent strips have strong positive correlations. However, the risk of a false negative result leading to incorrect certification of euhydration status outweighs the benefits of the HydraTrend reagent strips for the measurement of USG.

The effect of hydration status on the measurement of lean tissue mass by dual-energy X-ray absorptiometry.

PubMed

Toomey, Clodagh M; McCormack, William G; Jakeman, Phil

2017-03-01

Athletes cycle between exercise and recovery. Exercise invokes changes in total body water from thermal sweating, muscle and hepatic glycogen depletion and metabolic water loss. Recovery from exercise results in rehydration, substrate repletion, and possible glycogen supercompensation. Such changes may corrupt the measurement of hydrated tissues, such as lean tissue mass (LTM), by dual-energy X-ray absorptiometry (DXA). The purpose of this study was to determine the effect of exercise and thermal dehydration and subsequent glycogen supercompensation on DXA-based measurement of body composition. Twelve active adult (18-29 years) males exercised at 70% VO 2max on a cycle ergometer in a thermal environment (30 °C) to induce a 2.5% reduction in body mass. Participants subsequently underwent a glycogen supercompensation phase, whereby a high carbohydrate diet (8-12 g/kg body mass/day) was consumed for a 48-h period. Whole-body DXA measurement was performed at baseline, following exercise and supercompensation. Following exercise, mean body mass decreased by -1.93 kg (95% CI -2.3, -1.5), while total LTM decreased by -1.69 kg (-2.4, -1.0). Supercompensation induced a mean body mass increase of 2.53 kg (2.0, 3.1) and a total LTM increase of 2.36 kg (1.8, 2.9). No change in total fat mass or bone mineral content was observed at any timepoint. Training regimens that typically induce dehydration and nutrition regimens that involve carbohydrate loading can result in apparent changes to LTM measurement by DXA. Accurate measurement of LTM in athletes requires strict observation of hydration and glycogen status to prevent manipulation of results.

Surface and interlayer base-characters in lepidocrocite titanate: The adsorption and intercalation of fatty acid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maluangnont, Tosapol, E-mail: tosapol.ma@kmitl.ac.th; Catalytic Chemistry Research Unit, Faculty of Science, King Mongkut's Institute of Technology Ladkrabang, Bangkok 10520; Arsa, Pornanan

2016-06-15

While layered double hydroxides (LDHs) with positively-charged sheets are well known as basic materials, layered metal oxides having negatively-charged sheets are not generally recognized so. In this article, the surface and interlayer base-characters of O{sup 2−} sites in layered metal oxides have been demonstrated, taking lepidocrocite titanate K{sub 0.8}Zn{sub 0.4}Ti{sub 1.6}O{sub 4} as an example. The low basicity (0.04 mmol CO{sub 2}/g) and low desorption temperature (50–300 °C) shown by CO{sub 2}− TPD suggests that O{sup 2−} sites at the external surfaces is weakly basic, while those at the interlayer space are mostly inaccessible to CO{sub 2}. The liquid-phase adsorptionmore » study, however, revealed the uptake as much as 37% by mass of the bulky palmitic acid (C{sub 16} acid). The accompanying expansion of the interlayer space by ~0.1 nm was detected by PXRD and TEM. In an opposite manner to the external surfaces, the interlayer O{sup 2−} sites can deprotonate palmitic acid, forming the salt (i.e., potassium palmitate) occluded between the sheets. Two types of basic sites are proposed based on ultrafast {sup 1}H MAS NMR and FTIR results. The interlayer basic sites in lepidocrocite titanate leads to an application of this material as a selective and stable two-dimensional (2D) basic catalyst, as demonstrated by the ketonization of palmitic acid into palmitone (C{sub 31} ketone). Tuning of the catalytic activity by varying the type of metal (Zn, Mg, and Li) substituting at Ti{sup IV} sites was also illustrated. - Graphical abstract: Interlayer basic sites in lepidocrocite titanate, K{sub 0.8}Zn{sub 0.4}Ti{sub 1.6}O{sub 4}, lead to an intercalation of palmitic acid with a layer expansion. Display Omitted - Highlights: • K{sub 0.8}Zn{sub 0.4}Ti{sub 1.6}O{sub 4} intercalates palmitic acid, forming the occluded potassium salt. • The interlayer expansion is evidenced by PXRD patterns and TEM image. • Two types of basic sites are deduced from ultrafast {sup 1}H MAS NMR. • Lepidocrocite titanate catalyses ketonization of palmitic acid to palmitone and corresponding cracked products.« less

Measurement of the airway surface liquid volume with simple light refraction microscopy.

PubMed

Harvey, Peter R; Tarran, Robert; Garoff, Stephen; Myerburg, Mike M

2011-09-01

In the cystic fibrosis (CF) lung, the airway surface liquid (ASL) volume is depleted, impairing mucus clearance from the lung and leading to chronic airway infection and obstruction. Several therapeutics have been developed that aim to restore normal airway surface hydration to the CF airway, yet preclinical evaluation of these agents is hindered by the paucity of methods available to directly measure the ASL. Therefore, we sought to develop a straightforward approach to measure the ASL volume that would serve as the basis for a standardized method to assess mucosal hydration using readily available resources. Primary human bronchial epithelial (HBE) cells cultured at an air-liquid interface develop a liquid meniscus at the edge of the culture. We hypothesized that the size of the fluid meniscus is determined by the ASL volume, and could be measured as an index of the epithelial surface hydration status. A simple method was developed to measure the volume of fluid present in meniscus by imaging the refraction of light at the ASL interface with the culture wall using low-magnification microscopy. Using this method, we found that primary CF HBE cells had a reduced ASL volume compared with non-CF HBE cells, and that known modulators of ASL volume caused the predicted responses. Thus, we have demonstrated that this method can detect physiologically relevant changes in the ASL volume, and propose that this novel approach may be used to rapidly assess the effects of airway hydration therapies in high-throughput screening assays.

Potential-of-mean-force description of ionic interactions and structural hydration in biomolecular systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hummer, G.; Garcia, A.E.; Soumpasis, D.M.

1994-10-01

To understand the functioning of living organisms on a molecular level, it is crucial to dissect the intricate interplay of the immense number of biological molecules. Most of the biochemical processes in cells occur in a liquid environment formed mainly by water and ions. This solvent environment plays an important role in biological systems. The potential-of-mean-force (PMF) formalism attempts to describe quantitatively the interactions of the solvent with biological macromolecules on the basis of an approximate statistical-mechanical representation. At its current status of development, it deals with ionic effects on the biomolecular structure and with the structural hydration of biomolecules.more » The underlying idea of the PMF formalism is to identify the dominant sources of interactions and incorporate these interactions into the theoretical formalism using PMF`s (or particle correlation functions) extracted from bulk-liquid systems. In the following, the authors shall briefly outline the statistical-mechanical foundation of the PMF formalism and introduce the PMF expansion formalism, which is intimately linked to superposition approximations for higher-order particle correlation functions. The authors shall then sketch applications, which describe the effects of the ionic environment on nucleic-acid structure. Finally, the authors shall present the more recent extension of the PMF idea to describe quantitatively the structural hydration of biomolecules. Results for the interface of ice and water and for the hydration of deoxyribonucleic acid (DNA) will be discussed.« less

Reflectance and Mossbauer spectroscopy of ferrihydrite-montmorillonite assemblages as Mars soil analog materials

NASA Technical Reports Server (NTRS)

Bishop, J. L.; Pieters, C. M.; Burns, R. G.; Chang, S. (Principal Investigator)

1993-01-01

Spectroscopic analyses show that Fe(3+)-doped smectites prepared in the laboratory exhibit important similarities to the soils on Mars. Ferrihydrite has been identified as the interlayer ferric component in Fe(3+)-doped smectites by a low quadrupole splitting and magnetic field strength of approximately 48 tesla in Mossbauer spectra measured at 4.2 K, as well as a crystal field transition at 0.92 micrometer. Ferrihydrite in these smectites explains features in the visible-near infrared region that resemble the energies and band strengths of features in reflectance spectra observed for several bright regions on Mars. Clay silicates have met resistance in the past as Mars soil analogs because terrestrial clay silicates exhibit prominent hydrous spectral features at 1.4, 1.9, and 2.2 micrometers; and these are observed weakly, if at all, in reflectance spectra of Mars. However, several mechanisms can weaken or compress these features, including desiccation under low-humidity conditions. The hydration properties of the interlayer cations also effect band strengths, such that a ferrihydrite-bearing smectite in the Martian environment would exhibit a 1.9 micrometers H2O absorption that is even weaker than the 2.2 micrometers structural OH absorption. Mixing experiments demonstrate that infrared spectral features of clays can be significantly suppressed and that the reflectance can be significantly darkened by mixing with only a few percent of a strongly absorbing opaque material. Therefore, the absolute reflectance of a soil on Mars may be disproportionately sensitive to a minor component. For this reason, the shape and position of spectral features and the chemical composition of potential analogs are of utmost importance in assessing the composition of the soil on Mars. Given the remarkable similarity between visible-infrared reflectance spectra of soils in bright regions on Mars and Fe(3+)-doped montmorillonites, coupled with recent observations of smectites in SNC meteorites and a weak 2.2 micrometers absorption in some Mars soils, ferrihydrite-bearing smectites warrant serious consideration as a Mars soil analog.

An evaluation of interlayer stress absorbing composite (ISAC) reflective crack relief system

DOT National Transportation Integrated Search

2005-03-01

Reflective cracking of bituminous concrete overlays has long been a problem in pavement rehabilitation. Various types of interlayer systems and fabrics have been used to eliminate or slow the development of reflective cracks. These methods and produc...

Assessment of asphalt interlayer designed on jointed concrete : [tech transfer summary].

DOT National Transportation Integrated Search

2014-11-01

Based on the substantial reduction in reflective cracking and only marginal : cost increases from using the interlayer on this research project, it is : recommended that future hot mix asphalt (HMA) overlay projects in Iowa : consider using the crack...

Pavement service life extension due to asphalt surface treatment interlayer : research project capsule.

DOT National Transportation Integrated Search

2016-07-01

The Louisiana Department of Transportation and Development (DOTD) has been : using asphalt surface treatment (AST) interlayers over soil cement base courses : as a means to mitigate shrinkage cracks from reflecting through the asphaltic : concrete (A...

Strong Interlayer Magnon-Magnon Coupling in Magnetic Metal-Insulator Hybrid Nanostructures.

PubMed

Chen, Jilei; Liu, Chuanpu; Liu, Tao; Xiao, Yang; Xia, Ke; Bauer, Gerrit E W; Wu, Mingzhong; Yu, Haiming

2018-05-25

We observe strong interlayer magnon-magnon coupling in an on-chip nanomagnonic device at room temperature. Ferromagnetic nanowire arrays are integrated on a 20-nm-thick yttrium iron garnet (YIG) thin film strip. Large anticrossing gaps up to 1.58 GHz are observed between the ferromagnetic resonance of the nanowires and the in-plane standing spin waves of the YIG film. Control experiments and simulations reveal that both the interlayer exchange coupling and the dynamical dipolar coupling contribute to the observed anticrossings. The coupling strength is tunable by the magnetic configuration, allowing the coherent control of magnonic devices.

Strong Interlayer Magnon-Magnon Coupling in Magnetic Metal-Insulator Hybrid Nanostructures

NASA Astrophysics Data System (ADS)

Chen, Jilei; Liu, Chuanpu; Liu, Tao; Xiao, Yang; Xia, Ke; Bauer, Gerrit E. W.; Wu, Mingzhong; Yu, Haiming

2018-05-01

We observe strong interlayer magnon-magnon coupling in an on-chip nanomagnonic device at room temperature. Ferromagnetic nanowire arrays are integrated on a 20-nm-thick yttrium iron garnet (YIG) thin film strip. Large anticrossing gaps up to 1.58 GHz are observed between the ferromagnetic resonance of the nanowires and the in-plane standing spin waves of the YIG film. Control experiments and simulations reveal that both the interlayer exchange coupling and the dynamical dipolar coupling contribute to the observed anticrossings. The coupling strength is tunable by the magnetic configuration, allowing the coherent control of magnonic devices.

Low resistance contacts for shallow junction semiconductors

NASA Technical Reports Server (NTRS)

Fatemi, Navid S. (Inventor); Weizer, Victor G. (Inventor)

1994-01-01

A method of enhancing the specific contact resistivity in InP semiconductor devices and improved devices produced thereby are disclosed. Low resistivity values are obtained by using gold ohmic contacts that contain small amounts of gallium or indium and by depositing a thin gold phosphide interlayer between the surface of the InP device and the ohmic contact. When both the thin interlayer and the gold-gallium or gold-indium contact metallizations are used, ultra low specific contact resistivities are achieved. Thermal stability with good contact resistivity is achieved by depositing a layer of refractory metal over the gold phosphide interlayer.

Is Fluid Overload More Important than Diabetes in Renal Progression in Late Chronic Kidney Disease?

PubMed Central

Tsai, Yi-Chun; Tsai, Jer-Chia; Chiu, Yi-Wen; Kuo, Hung-Tien; Chen, Szu-Chia; Hwang, Shang-Jyh; Chen, Tzu-Hui; Kuo, Mei-Chuan; Chen, Hung-Chun

2013-01-01

Fluid overload is one of the major presentations in patients with late stage chronic kidney disease (CKD). Diabetes is the leading cause of renal failure, and progression of diabetic nephropathy has been associated with changes in extracellular fluid volume. The aim of the study was to assess the association of fluid overload and diabetes in commencing dialysis and rapid renal function decline (the slope of estimated glomerular filtration rate (eGFR) less than -3 ml/min per 1.73 m2/y) in 472 patients with stages 4-5 CKD. Fluid status was determined by bioimpedance spectroscopy method, Body Composition Monitor. The study population was further classified into four groups according to the median of relative hydration status (△HS =fluid overload/extracellular water) and the presence or absence of diabetes. The median level of relative hydration status was 7%. Among all patients, 207(43.9 %) were diabetic. 71 (15.0%) subjects had commencing dialysis, and 187 (39.6%) subjects presented rapid renal function decline during a median 17.3-month follow-up. Patients with fluid overload had a significantly increased risk for commencing dialysis and renal function decline independent of the presence or absence of diabetes. No significantly increased risk for renal progression was found between diabetes and non-diabetes in late CKD without fluid overload. In conclusion, fluid overload has a higher predictive value of an elevated risk for renal progression than diabetes in late CKD. PMID:24349311

The Coherent Interlayer Resistance of a Single, Misoriented Interface between Two Graphite Stacks

NASA Astrophysics Data System (ADS)

Lake, Roger K.; Habib, K. M. Masum; Sylvia, Somaia; Ge, Supeng; Neupane, Mahesh

2014-03-01

The coherent, interlayer resistance of a misoriented, rotated interface between two stacks of AB graphite is determined for a variety of misorientation angles ranging from 0° to 27 .29° . The quantum-resistance of the ideal AB stack is on the order of 1 to 10 m Ωμm2 depending on the Fermi energy. For small rotation angles <= 7 .34° , the coherent interlayer resistance exponentially approaches the ideal quantum resistance at energies away from the charge neutrality point. Over a range of intermediate angles, the resistance increases exponentially with primitive cell size for minimum size cells. A change of misorientation angle by one degree can increase the primitive cell size by three orders of magnitude. These large cell sizes may not follow the exponential trend of the minimal cells especially at energies a few hundred meV away from the charge neutrality point. At such energies, their coherent interlayer resistance is likely to coincide with that of a nearby rotation angle with a much smaller primitive cell. The energy dependence of the interlayer transmission is described and analyzed. This work was supported in part by FAME, one of six centers of STARnet, a Semiconductor Research Corporation program sponsored by MARCO and DARPA.

Two-Dimensional Jeff=1 /2 Antiferromagnetic Insulator Unraveled from Interlayer Exchange Coupling in Artificial Perovskite Iridate Superlattices

NASA Astrophysics Data System (ADS)

Hao, Lin; Meyers, D.; Frederick, Clayton; Fabbris, Gilberto; Yang, Junyi; Traynor, Nathan; Horak, Lukas; Kriegner, Dominik; Choi, Yongseong; Kim, Jong-Woo; Haskel, Daniel; Ryan, Phil J.; Dean, M. P. M.; Liu, Jian

2017-07-01

We report an experimental investigation of the two-dimensional Jeff=1 /2 antiferromagnetic Mott insulator by varying the interlayer exchange coupling in [(SrIrO3)1 , (SrTiO3)m ] (m =1 , 2 and 3) superlattices. Although all samples exhibited an insulating ground state with long-range magnetic order, temperature-dependent resistivity measurements showed a stronger insulating behavior in the m =2 and m =3 samples than the m =1 sample which displayed a clear kink at the magnetic transition. This difference indicates that the blocking effect of the excessive SrTiO3 layer enhances the effective electron-electron correlation and strengthens the Mott phase. The significant reduction of the Néel temperature from 150 K for m =1 to 40 K for m =2 demonstrates that the long-range order stability in the former is boosted by a substantial interlayer exchange coupling. Resonant x-ray magnetic scattering revealed that the interlayer exchange coupling has a switchable sign, depending on the SrTiO3 layer number m , for maintaining canting-induced weak ferromagnetism. The nearly unaltered transition temperature between the m =2 and the m =3 demonstrated that we have realized a two-dimensional antiferromagnet at finite temperatures with diminishing interlayer exchange coupling.

Web-structured graphitic carbon fiber felt as an interlayer for rechargeable lithium-sulfur batteries with highly improved cycling performance

NASA Astrophysics Data System (ADS)

Lee, Dong Kyu; Ahn, Chi Won; Jeon, Hwan-Jin

2017-08-01

Graphitic carbon fiber felt (GCFF) with a crystalline graphitic carbon structure was facilely prepared by a combination of electrospinning and graphitization (2800 °C heat treatment) and was used as an interlayer between the cathode and separator in Li-S batteries. This GCFF interlayer trapped the polysulfides on the cathode side and increased the utilization of sulfur by suppressing the shuttle phenomenon. Also, the GCFF was shown to be able to act as an upper current collector to reduce the charge-transfer resistance owing to the high crystallinity of the graphitic carbon fibers. The sulfur cathode with the GCFF interlayer showed a high specific initial discharge capacity of 1280.14 mAh g-1 and excellent cycling stability (1004.62 mAh g-1 after 100 cycles) at 0.2 C. Also, an image of the glass fiber (GF) separator on the anode side confirmed the presence of an SEI after 200 cycles, which apparently resulted from stable Li deposition on the Li metal because of the low or medium concentration of sulfur in the electrolyte solution. Our observations should contribute to elucidating the key features of complex three-dimensional carbon fabrics with crystalline graphitic structures that allow them, when inserted as interlayers, to markedly improve the performance of rechargeable batteries.

Effect of SiC interlayer between Ti6Al4V alloy and hydroxyapatite films.

PubMed

Azem, Funda Ak; Birlik, Isil; Braic, Viorel; Toparli, Mustafa; Celik, Erdal; Parau, Anca; Kiss, Adrian; Titorencu, Irina; Vladescu, Alina

2015-04-01

Bioactive coatings are frequently used to improve the osseointegration of the metallic implants used in dentistry or orthopaedics. Among different types of bioactive coatings, hydroxyapatite (Ca10(PO4)6(OH)2) is one of the most extensively used due to its chemical similarities to the components of bones and teeth. In this article, production and characterization of hydroxyapatite films deposited on Ti6Al4V alloy prepared by magnetron sputtering were reported. Besides, SiC was deposited on substrate surface to study the interlayer effect. Obtained coatings were annealed at 600 °C for 30 and 120 min in a mixed atmosphere of N2 + H2O vapours with the heating rate of 12 °C min(-1). The effects of SiC interlayer and heat treatment parameters on the structural, mechanical and corrosion properties were investigated. After heat treatment process, the crystalline hydroxyapatite was obtained. Additionally, cell viability tests were performed. The results show that the presence of the SiC interlayer contributes a decrease in surface roughness and improves the mechanical properties and corrosion performance of the hydroxyapatite coatings. Biological properties were not affected by the presence of the SiC interlayer. © IMechE 2015.

NiCrNx interlayer thickness dependence of spectral performance and environmental durability of protected-silver mirrors

NASA Astrophysics Data System (ADS)

Xu, Xu; Li, Bincheng; He, Wenyan; Wang, Changjun; Wei, Ming

2018-04-01

Gemini-style protected-silver mirror (Sub / NiCrNx / Ag / NiCrNx / SiNx / Air) is a suitable choice for optical instruments requiring both long-term environmental durability and high broadband reflectance. Three Gemini-style protected-silver mirrors with NiCrNx interlayer thicknesses between 0.1 and 0.6 nm were prepared by magnetron sputtering, and the dependences of spectral properties and environmental durability of these protected-silver mirrors on the thickness of NiCrNx interlayer between the silver layer and SiNx layer were investigated in-depth. The reflectance, transmittance and total scattering loss measurements, optical microscope, and scanning electron microscope imaging were employed to characterize the spectral properties and surface morphology, and accelerated environmental tests, including humidity test and salt fog test, were applied to investigate the environmental durability. The experimental results showed that both optical and corrosion-resistant properties of protected-silver mirrors were NiCrNx interlayer thickness dependent, and an optimum NiCrNx interlayer thickness should be ˜0.3 nm for Gemini-style protected-silver mirrors to have reasonably both high reflectance in a broadband spectral range from visible to far infrared and good corrosion resistance for long-lifetime applications in harsh environments.

Effect of integrating straw into agricultural soils on soil infiltration and evaporation.

PubMed

Cao, Jiansheng; Liu, Changming; Zhang, Wanjun; Guo, Yunlong

2012-01-01

Soil water movement is a critical consideration for crop yield in straw-integrated fields. This study used an indoor soil column experiment to determine soil infiltration and evaporation characteristics in three forms of direct straw-integrated soils (straw mulching, straw mixing and straw inter-layering). Straw mulching is covering the land surface with straw. Straw mixing is mixing straw with the top 10 cm surface soil. Then straw inter-layering is placing straw at the 20 cm soil depth. There are generally good correlations among the mulch integration methods at p < 0.05, and with average errors/biases <10%. Straw mixing exhibited the best effect in terms of soil infiltration, followed by straw mulching. Due to over-burden weight-compaction effect, straw inter-layering somehow retarded soil infiltration. In terms of soil water evaporation, straw mulching exhibited the best effect. This was followed by straw mixing and then straw inter-layering. Straw inter-layering could have a long-lasting positive effect on soil evaporation as it limited the evaporative consumption of deep soil water. The responses of the direct straw integration modes to soil infiltration and evaporation could lay the basis for developing efficient water-conservation strategies. This is especially useful for water-scarce agricultural regions such as the arid/semi-arid regions of China.

Effect of the hexagonal phase interlayer on rectification properties of boron nitride heterojunctions to silicon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teii, K., E-mail: teii@asem.kyushu-u.ac.jp; Ito, H.; Katayama, N.

2015-02-07

Rectification properties of boron nitride/silicon p-n heterojunction diodes fabricated under low-energy ion impact by plasma-enhanced chemical vapor deposition are studied in terms of the resistive sp{sup 2}-bonded boron nitride (sp{sup 2}BN) interlayer. A two-step biasing technique is developed to control the fraction of cubic boron nitride (cBN) phase and, hence, the thickness of the sp{sup 2}BN interlayer in the films. The rectification ratio at room temperature is increased up to the order of 10{sup 4} at ±10 V of biasing with increasing the sp{sup 2}BN thickness up to around 130 nm due to suppression of the reverse leakage current. The variation ofmore » the ideality factor in the low bias region is related to the interface disorders and defects, not to the sp{sup 2}BN thickness. The forward current follows the Frenkel-Poole emission model in the sp{sup 2}BN interlayer at relatively high fields when the anomalous effect is assumed. The transport of the minority carriers for reverse current is strongly limited by the high bulk resistance of the thick sp{sup 2}BN interlayer, while that of the major carriers for forward current is much less affected.« less

A structural coarse-grained model for clays using simple iterative Boltzmann inversion

NASA Astrophysics Data System (ADS)

Schaettle, Karl; Ruiz Pestana, Luis; Head-Gordon, Teresa; Lammers, Laura Nielsen

2018-06-01

Cesium-137 is a major byproduct of nuclear energy generation and is environmentally threatening due to its long half-life and affinity for naturally occurring micaceous clays. Recent experimental observations of illite and phlogopite mica indicate that Cs+ is capable of exchanging with K+ bound in the anhydrous interlayers of layered silicates, forming sharp exchange fronts, leading to interstratification of Cs- and K-illite. We present here a coarse-grained (CG) model of the anhydrous illite interlayer developed using iterative Boltzmann inversion that qualitatively and quantitatively reproduces features of a previously proposed feedback mechanism of ion exchange. The CG model represents a 70-fold speedup over all-atom models of clay systems and predicts interlayer expansion for K-illite near ion exchange fronts. Contrary to the longstanding theory that ion exchange in a neighboring layer increases the binding of K in lattice counterion sites leading to interstratification, we find that the presence of neighboring exchanged layers leads to short-range structural relaxations that increase basal spacing and decrease cohesion of the neighboring K-illite layers. We also provide evidence that the formation of alternating Cs- and K-illite interlayers (i.e., ordered interstratification) is both thermodynamically and mechanically favorable compared to exchange in adjacent interlayers.

Interlayer Coupling and Gate-Tunable Excitons in Transition Metal Dichalcogenide Heterostructures

DOE PAGES

Gao, Shiyuan; Yang, Li; Spataru, Catalin Dan

2017-11-22

Bilayer van der Waals (vdW) heterostructures such as MoS 2/WS 2 and MoSe 2/WSe 2 have attracted much attention recently, particularly because of their type II band alignments and the formation of interlayer exciton as the lowest-energy excitonic state. In this work, we calculate the electronic and optical properties of such heterostructures with the first-principles GW+Bethe–Salpeter Equation (BSE) method and reveal the important role of interlayer coupling in deciding the excited-state properties, including the band alignment and excitonic properties. Our calculation shows that due to the interlayer coupling, the low energy excitons can be widely tuned by a vertical gatemore » field. In particular, the dipole oscillator strength and radiative lifetime of the lowest energy exciton in these bilayer heterostructures is varied by over an order of magnitude within a practical external gate field. We also build a simple model that captures the essential physics behind this tunability and allows the extension of the ab initio results to a large range of electric fields. In conclusion, our work clarifies the physical picture of interlayer excitons in bilayer vdW heterostructures and predicts a wide range of gate-tunable excited-state properties of 2D optoelectronic devices.« less

Thickness effects of yttria-doped ceria interlayers on solid oxide fuel cells

NASA Astrophysics Data System (ADS)

Fan, Zeng; An, Jihwan; Iancu, Andrei; Prinz, Fritz B.

2012-11-01

Determining the optimal thickness range of the interlayed yttria-doped ceria (YDC) films promises to further enhance the performance of solid oxide fuel cells (SOFCs) at low operating temperatures. The YDC interlayers are fabricated by the atomic layer deposition (ALD) method with one super cycle of the YDC deposition consisting of 6 ceria deposition cycles and one yttria deposition cycle. YDC films of various numbers of ALD super cycles, ranging from 2 to 35, are interlayered into bulk fuel cells with a 200 um thick yttria-stabilized zirconia (YSZ) electrolyte. Measurements and analysis of the linear sweep voltammetry of these fuel cells reveal that the performance of the given cells is maximized at 10 super cycles. Auger elemental mapping and X-ray photoelectron spectroscopy (XPS) techniques are employed to determine the film completeness, and they verify 10 super cycles of YDC to be the critical thickness point. This optimal YDC interlayer condition (6Ce1Y × 10 super cycles) is applied to the case of micro fuel cells as well, and the average performance enhancement factor is 1.4 at operating temperatures of 400 and 450 °C. A power density of 1.04 W cm-2 at 500 °C is also achieved with the optimal YDC recipe.

Unconventional energy resources: 2007-2008 review

USGS Publications Warehouse

Warwick, Peter D.; ,

2009-01-01

This paper summarizes five 2007–2008 resource commodity committee reports prepared by the Energy Minerals Division (EMD) of the American Association of Petroleum Geologists. Current United States and global research and development activities related to gas hydrates, gas shales, geothermal resources, oil sands, and uranium resources are included in this review. These commodity reports were written to advise EMD leadership and membership of the current status of research and development of unconventional energy resources. Unconventional energy resources are defined as those resources other than conventional oil and natural gas that typically occur in sandstone and carbonate rocks. Gas hydrate resources are potentially enormous; however, production technologies are still under development. Gas shale, geothermal, oil sand, and uranium resources are now increasing targets of exploration and development, and are rapidly becoming important energy resources that will continue to be developed in the future.

Water, Hydration and Health

PubMed Central

Popkin, Barry M.; D’Anci, Kristen E.; Rosenberg, Irwin H.

2010-01-01

This review attempts to provide some sense of our current knowledge of water including overall patterns of intake and some factors linked with intake, the complex mechanisms behind water homeostasis, the effects of variation in water intake on health and energy intake, weight, and human performance and functioning. Water represents a critical nutrient whose absence will be lethal within days. Water’s importance for prevention of nutrition-related noncommunicable diseases has emerged more recently because of the shift toward large proportions of fluids coming from caloric beverages. Nevertheless, there are major gaps in knowledge related to measurement of total fluid intake, hydration status at the population level, and few longer-term systematic interventions and no published random-controlled longer-term trials. We suggest some ways to examine water requirements as a means to encouraging more dialogue on this important topic. PMID:20646222

Changes in the Arctic: Background and Issues for Congress

DTIC Science & Technology

2016-05-12

discovery of new oil and gas deposits far from existing storage, pipelines , and shipping facilities cannot be developed until infrastructure is built...markets. Other questions in need of answers include the status of port, pipeline , and liquid natural gas infrastructure; whether methane hydrates...Changes to the Arctic brought about by warming temperatures will likely allow more exploration for oil, gas , and minerals. Warming that causes

The effect of exercise on water balance in premenopausal physically active women.

PubMed

Weinheimer, Eileen M; Martin, Berdine R; Weaver, Connie M; Welch, Jo M; Campbell, Wayne W

2008-10-01

This controlled feeding study examined the effects of exercise on daily water intake (particularly ad libitum water intake), water output, whole-body water balance, and hydration status in physically active, premenopausal women. The randomized crossover design consisted of three 8-day trials: placebo and no exercise, placebo and exercise (1-hour cycling bout per day at 65%-70% of heart rate reserve), and 800 mg calcium supplementation and exercise. During each trial, controlled quantities of the same foods and beverages were provided and ad libitum water intake was quantified. Water input included measured water from foods and beverages, measured ad libitum intake, and estimated metabolic production. Water output included measured losses in urine and stool, and estimated insensible losses from respiration and non-sweating perspiration (insensible diffusion through the skin). Participants were 26 women, age 25+/-5 years, body mass index 22+/-2, and VO(2peak) 43+/-6 mLxkg(-1)xmin(-1) (mean+/-standard deviation). Ad libitum water intake was 363 g/day more (P<0.05) for the placebo and exercise (1,940+/-654 g/day) and calcium supplementation and exercise (1,935+/-668 g/day) trials, compared with placebo and no exercise trial (1,575+/-667 g/day), and total water input was correspondingly higher in placebo and exercise and calcium supplementation and exercise trials compared with the placebo and no exercise trial. Urine, stool, and total water outputs were not different among trials. Apparent net water balance (representative of sweat water output) was 367 g/day more (P<0.05) in placebo and exercise (679+/-427 g/day) and calcium supplementation and exercise (641+/-519 g/day) trials compared with placebo and no exercise trial (293+/-419 g/day). Hydration status was clinically normal during all three trials. Calcium supplementation did not influence water balance. These results support that young, physically active women can completely compensate for exercise-induced sweat losses by increasing ad libitum water intake, and not decreasing non-sweat water outputs or impairing hydration status.

Long-term field monitoring of paving fabric interlayer systems to reduce reflective cracking.

DOT National Transportation Integrated Search

2016-06-01

The formation of reflective cracking of pavement overlays has confronted highway engineers for many years. Stress-relieving interlayers, such as paving fabrics, have been used in an attempt to reduce or delay reflective cracking. The primary objectiv...

Gadolinium doped ceria interlayers for Solid Oxide Fuel Cells cathodes: Enhanced reactivity with sintering aids (Li, Cu, Zn), and improved densification by infiltration

NASA Astrophysics Data System (ADS)

Nicollet, Clement; Waxin, Jenny; Dupeyron, Thomas; Flura, Aurélien; Heintz, Jean-Marc; Ouweltjes, Jan Pieter; Piccardo, Paolo; Rougier, Aline; Grenier, Jean-Claude; Bassat, Jean-Marc

2017-12-01

This paper reports the study of the densification of 20% Gd doped ceria (Ce0.8Gd0.2O1.9 (GDC)) interlayers in SOFC cathodes through two different routes: the well-known addition of sintering elements, and an innovative densification process by infiltration. First, Li, Cu, and Zn nitrates were added to GDC powders. The effect of these additives on the densification was studied by dilatometry on pellets, and show a large decrease of the sintering temperature from 1330 °C (pure GDC), down to 1080 °C, 950 °C, and 930 °C for Zn, Cu, and Li addition, respectively. However, this promising result does not apply to screen-printed layers, which are more porous than pellets and in which the shrinkage is constrained by the substrate. The second approach consists in preparing a pre-sintered GDC layer, which is subsequently infiltrated with Ce and Gd nitrates and sintered at 1250 °C to increase its density. Such an approach results in highly dense GDC interlayers. Using La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) as electrode, the influence of the interlayers on the cathode performance was studied. The addition of sintering aids dramatically increases the cell resistances, most likely because the additives increase the reactivity between GDC and either Yttria Stabilized Zirconia (YSZ) or LSCF, thus losing the expected benefit related to the decrease of sintering temperatures. The interlayers prepared by infiltration do not induce additional resistances in the cell, which results in power densities of single cells 40-50% higher than those of cells prepared with commercial GDC interlayers, making this approach a valuable alternative to sintering aids.

Improvement of the thermal stability of nickel silicide using a ruthenium interlayer deposited via remote plasma atomic layer deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Inhye; Park, Jingyu; Jeon, Heeyoung

In this study, the effects of a thin Ru interlayer on the thermal and morphological stability of NiSi have been investigated. Ru and Ni thin films were deposited sequentially to form a Ni/Ru/Si bilayered structure, without breaking the vacuum, by remote plasma atomic layer deposition (RPALD) on a p-type Si wafer. After annealing at various temperatures, the thermal stabilities of the Ni/Ru/Si and Ni/Si structures were investigated by various analysis techniques. The results showed that the sheet resistance of the Ni/Ru/Si sample was consistently lower compared to the Ni/Si sample over the entire temperature range. Although both samples exhibited themore » formation of NiSi{sub 2} phases at an annealing temperature of 800 °C, as seen with glancing angle x-ray diffraction, the peaks of the Ni/Ru/Si sample were observed to have much weaker intensities than those obtained for the Ni/Si sample. Moreover, the NiSi film with a Ru interlayer exhibited a better interface and improved surface morphologies compared to the NiSi film without a Ru interlayer. These results show that the phase transformation of NiSi to NiSi{sub 2} was retarded and that the smooth NiSi/Si interface was retained due to the activation energy increment for NiSi{sub 2} nucleation that is caused by adding a Ru interlayer. Hence, it can be said that the Ru interlayer deposited by RPALD can be used to control the phase transformation and physical properties of nickel silicide phases.« less

Velocity Structure and 3D Finite Element Modeling for Critical Instability of Gas Hydrate-related Slipstream Submarine Slide, offshore Vancouver Island, Canada

NASA Astrophysics Data System (ADS)

LONG, S.; He, T.; Lan, K.; Spence, G.; Yelisetti, S.

2016-12-01

The previous study indicated that Slipstream submarine landslide is one of a gas hydrate-related slope failures on the frontal ridges of the Northern Cascadia accretionary margin, off Vancouver Island, Canada. The OBS data collected during SeaJade project were used to derive the subseafloor Vp & Vs structures. The anomalous high Vp of about 2.0 km/s at shallow depths of 100 (± 10) mbsf closely matches the estimated depth of the glide plane. The modelled Vs above the BSR at a depth of 265-275 mbsf is about 100-150 m/s higher than a theoretical 100% water saturated background value, indicating that the hydrate acts as part of the load-bearing matrix to increase the rigidity of the sediment. Also, the Vp & Vs above BSR both indicate a consistent 40% saturation of gas hydrate. On the basis of high accurate submarine bathymetry obtained by multibeam sounding system, the submarine landform before slump is reconstructed by comparing the slump headwall geometry with surrounding ridges. Using the elastic moduli determined from Vp & Vs, the stress status was calculated by the finite element method for different conditions and confirmed that the undersea sliding process related with gas hydrate starts from the toe of the slope and then progressively retreats to the place of current headwall, in a series of triangular blocks or wedges. The shear stress are then compared with the frame shear strength of geological model, which is critical for controlling slope stability of steep frontal ridges The simulation results found that the ridge was stable under its own weight, but gas hydrate saturation decrease and pore-water pressure increase will greatly reduce shear strength of sediments and may cause a landslide. Since the study area is in the earthquake belt, the large seismic acceleration will greatly affect pore pressure distribution within the ridge. The simulation results indicated that the shallow high-velocity gas hydrate layer coincident with glide plane depth is more likely to fail than the current BSR observations during an earthquake. Combining with regional tectonic background, it is initially deduced that the large earthquake is the most possible trigger of Slipstream landslide.

Investigation of Wyoming Bentonite Hydration in Dry to Water-Saturated Supercritical CO2: Implications for Caprock Integrity

NASA Astrophysics Data System (ADS)

Loring, J. S.; Chen, J.; Thompson, C.; Schaef, T.; Miller, Q. R.; Martin, P. F.; Ilton, E. S.; Qafoku, O.; Felmy, A. R.; Rosso, K. M.

2012-12-01

The effectiveness of geologic sequestration as an enterprise for CO2 storage depends partly on the reactivity of supercritical CO2 (scCO2) with caprock minerals. Injection of scCO2 will displace formation water, and the pore space adjacent to overlying caprocks could eventually be dominated by dry to water-saturated scCO2. Caprock formations have high concentrations of clay minerals, including expandable montmorillonites. Water-bearing scCO2 is highly reactive and capable of hydrating or dehydrating clays, possibly leading to porosity and permeability changes that directly impact caprock performance. Dehydration will cause montmorillonite clay minerals in caprocks to contract, thereby decreasing solid volume and possibly increasing caprock permeability and porosity. On the other hand, water intercalation will cause these clays to expand, thereby increasing solid volume and possibly leading to self-sealing of caprock fractures. Pacific Northwest National Laboratory's Carbon Sequestration Initiative is developing capabilities for studying wet scCO2-mineral reactions in situ. Here, we introduce novel in situ infrared (IR) spectroscopic instrumentation that enables quantitative titrations of reactant minerals with water in scCO2. Results are presented for the infrared spectroscopic titrations of Na-, Ca-, and Mg-saturated Wyoming betonites with water over concentrations ranging from zero to scCO2 saturated. These experiments were carried out at 50°C and 90 bar. Transmission IR spectroscopy was used to measure concentrations of water dissolved in the scCO2 or intercalated into the clays. The titration curves evaluated from the transmission-IR data are compared between the three types of clays to assess the effects of the cation on water partitioning. Single-reflection attenuated total reflection (ATR) IR spectroscopy was used to collect the spectrum of the clays as they hydrate at every total water concentration during the titration. Clay hydration is evidenced by increases in absorbance of the OH stretching and HOH bending modes of the intercalated waters. The ATR-IR data also indicate that CO2 is intercalated in the clay. The asymmetric stretching band of the CO2 molecules that are intercalated in the clay is narrower than that stretching band of bulk scCO2, which indicates that the spectral contribution from rotational fine structure is minimal and the intercalated CO2 is rotationally constrained. A chemometrics analysis of the complete set of ATR-IR spectra spanning the range of total water concentrations covered in the titration finds that there are at least two types of intercalated waters, two types of intercalated CO2 molecules, and the concentrations of these intercalated waters and CO2 molecules are correlated. These quantitative data, when coupled with in situ XRD results that predict interlayer spacing and clay volume, demonstrate that water and CO2 intercalation processes in expandable montmorillonite clays could lead to porosity and permeability changes that directly impact caprock performance.

Pore-Size-Tuned Graphene Oxide Frameworks as Ion-Selective and Protective Layers on Hydrocarbon Membranes for Vanadium Redox-Flow Batteries.

PubMed

Kim, Soohyun; Choi, Junghoon; Choi, Chanyong; Heo, Jiyun; Kim, Dae Woo; Lee, Jang Yong; Hong, Young Taik; Jung, Hee-Tae; Kim, Hee-Tak

2018-05-07

The laminated structure of graphene oxide (GO) membranes provides exceptional ion-separation properties due to the regular interlayer spacing ( d) between laminate layers. However, a larger effective pore size of the laminate immersed in water (∼11.1 Å) than the hydrated diameter of vanadium ions (>6.0 Å) prevents its use in vanadium redox-flow batteries (VRFB). In this work, we report an ion-selective graphene oxide framework (GOF) with a d tuned by cross-linking the GO nanosheets. Its effective pore size (∼5.9 Å) excludes vanadium ions by size but allows proton conduction. The GOF membrane is employed as a protective layer to address the poor chemical stability of sulfonated poly(arylene ether sulfone) (SPAES) membranes against VO 2 + in VRFB. By effectively blocking vanadium ions, the GOF/SPAES membrane exhibits vanadium-ion permeability 4.2 times lower and a durability 5 times longer than that of the pristine SPAES membrane. Moreover, the VRFB with the GOF/SPAES membrane achieves an energy efficiency of 89% at 80 mA cm -2 and a capacity retention of 88% even after 400 cycles, far exceeding results for Nafion 115 and demonstrating its practical applicability for VRFB.

Microstructure and supercapacitive properties of buserite-type manganese oxide with a large basal spacing

NASA Astrophysics Data System (ADS)

Sun, Zhenjie; Shu, Dong; Chen, Hongyu; He, Chun; Tang, Shaoqing; Zhang, Jie

2012-10-01

A hydration-layered structure of buserite-type manganese oxide (Mg-buserite) was successfully synthesized by an ion exchange method. The as-prepared Mg-buserite possesses a large basal spacing of 10 Å, and contains Mg2+ ions and two sheets of water molecules in the interlayer region. The supercapacitive behaviors of Mg-buserite were systematically investigated by cyclic voltammetry (CV), galvanostatic charge-discharge (CD) experiments and electrochemical impedance spectroscopy (EIS). The results showed that the specific capacitance of the Mg-buserite electrode sharply increased during the initial 500 cycles and reached a maximum of 164 F g-1 at approximately the 500th cycle at a scan rate of 1 mV s-1, and then it remained an almost constant value and decreased slightly upon prolonged cycling. After 22,000 cycles, the specific capacitance decreased by approximately 6% of the maximum specific capacitance. The superior capacitive behavior and excellent cycling stability of the as-prepared Mg-buserite are attributed to the large basal spacing, which can accommodate a larger amount of electrolyte cations and provide more favorable pathways for electrolyte cations intercalation and deintercalation. The experimental results demonstrate that Mg-buserite is a promising candidate as an electrode material for supercapacitors.

Robust and underwater superoleophobic coating with excellent corrosion and biofouling resistance in harsh environments

NASA Astrophysics Data System (ADS)

Su, Mingji; Liu, Yong; Zhang, Yuhong; Wang, Zhiguo; Li, Yulin; He, Peixin

2018-04-01

Underwater superoleophobic surfaces are based on the surface with micro-/nanoscale roughness and hydration layer. But the self-cleaning surfaces are usually mechanically weak and will lose their underwater superoleophobicity when the surfaces are corroded or damaged. In this paper, to overcome these problems, the robust underwater superoleophobic coating (HN/ER-coating) has been fabricated successfully through MPS (methacryloxy propyl trimethoxyl silane)-SiO2/PNIPAM (N-isopropylacryamide) hybrid nanoparticles and epoxy resin (ER) via a simple solution-casting method. The SiO2/PNIPAM hybrid nanoparticles can enhance multiscale roughness and excellent abrasion-resistant property, and the epoxy resin can be used as an interlayer between hybrid nanoparticles and substrates to promote the robustness and corrosion resistance of the coating. The obtained coatings have excellent underwater superoleophobicity, and exhibit highly stability in harsh environments (including acid-base, strong ionic strength, mechanical abrasion). Moreover, this coating can provide protective effect on the substrate in corrosive solution, and may also resist bacterial attachment and subsequent biofilm formation because of the presence of high density PNIPAM polymers. Herein, the developed underwater superoleophobic coating can be applied as an effective platform for the applications in underwater instruments, underwater oil transport, marine oil platform and ships.

Unequal density effect on static structure factor of coupled electron layers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saini, L. K., E-mail: lks@ashd.svnit.ac.in; Nayak, Mukesh G., E-mail: lks@ashd.svnit.ac.in

In order to understand the ordered phase, if any, in a real coupled electron layers (CEL), there is a need to take into account the effect of unequal layer density. Such phase is confirmed by a strong peak in a static structure factor. With the aid of quantum/dynamical version of Singwi, Tosi, Land and Sjölander (so-called qSTLS) approximation, we have calculated the intra- and interlayer static structure factors, S{sub ll}(q) and S{sub 12}(q), over a wide range of density parameter r{sub sl} and interlayer spacing d. In our present study, the sharp peak in S{sub 22}(q) has been found atmore » critical density with sufficiently lower interlayer spacing. Further, to find the resultant effect of unequal density on intra- and interlayer static structure factors, we have compared our results with that of the recent CEL system with equal layer density and isolated single electron layer.« less

Barrier height enhancement of metal/semiconductor contact by an enzyme biofilm interlayer

NASA Astrophysics Data System (ADS)

Ocak, Yusuf Selim; Gul Guven, Reyhan; Tombak, Ahmet; Kilicoglu, Tahsin; Guven, Kemal; Dogru, Mehmet

2013-06-01

A metal/interlayer/semiconductor (Al/enzyme/p-Si) MIS device was fabricated using α-amylase enzyme as a thin biofilm interlayer. It was observed that the device showed an excellent rectifying behavior and the barrier height value of 0.78 eV for Al/α-amylase/p-Si was meaningfully larger than the one of 0.58 eV for conventional Al/p-Si metal/semiconductor (MS) contact. Enhancement of the interfacial potential barrier of Al/p-Si MS diode was realized using enzyme interlayer by influencing the space charge region of Si semiconductor. The electrical properties of the structure were executed by the help of current-voltage and capacitance-voltage measurements. The photovoltaic properties of the structure were executed under a solar simulator with AM1.5 global filter between 40 and 100 mW/cm2 illumination conditions. It was also reported that the α-amylase enzyme produced from Bacillus licheniformis had a 3.65 eV band gap value obtained from optical method.

Edge-terminated molybdenum disulfide with a 9.4-Å interlayer spacing for electrochemical hydrogen production

DOE PAGES

Gao, Min -Rui; Chan, Maria K. Y.; Sun, Yugang

2015-07-03

In this study, layered molybdenum disulfide has demonstrated great promise as a low-cost alternative to platinum-based catalysts for electrochemical hydrogen production from water. Research effort on this material has focused mainly on synthesizing highly nanostructured molybdenum disulfide that allows the exposure of a large fraction of active edge sites. Here we report a promising microwave-assisted strategy for the synthesis of narrow molybdenum disulfide nanosheets with edge-terminated structure and a significantly expanded interlayer spacing, which exhibit striking kinetic metrics with onset potential of -103 mV, Tafel slope of 49 mV per decade and exchange current density of 9.62 × 10 -3more » mA cm -2, performing among the best of current molybdenum disulfide catalysts. Besides benefits from the edge-terminated structure, the expanded interlayer distance with modified electronic structure is also responsible for the observed catalytic improvement, which suggests a potential way to design newly advanced molybdenum disulfide catalysts through modulating the interlayer distance.« less

Bi-quadratic interlayer exchange coupling in Co{sub 2}MnSi/Ag/Co{sub 2}MnSi pseudo spin-valve

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goripati, Hari S.; Hono, K.; Graduate School of Pure and Applied Sciences, University of Tsukuba, Tsukuba 305-0047

2011-12-15

Bi-quadratic interlayer exchange coupling is found below 100 K in a Co{sub 2}MnSi/Ag/Co{sub 2}MnSi current-perpendicular-to-plane pseudo spin valves. The bi-quadratic coupling constant J{sub 2} was estimated to be {approx}-0.30 erg/cm{sup 2} at 5 K and the strong temperature dependence of the coupling strength points its likely origin to the ''loose spin'' model. Application of current of {approx}2 x 10{sup 7} A/cm{sup 2} below 100 K leads to an increase in the magnetoresistance (MR), indicating current induced antiparallel alignment of the two magnetic layers. These results strongly suggest that the presence of the bi-quadratic interlayer exchange coupling causes the reduction ofmore » the magnetoresistance at low temperature and illustrates the importance of understanding the influence of interlayer exchange coupling on magnetization configuration in magnetic nanostructures.« less

Recombination zone in white organic light emitting diodes with blue and orange emitting layers

NASA Astrophysics Data System (ADS)

Tsuboi, Taiju; Kishimoto, Tadashi; Wako, Kazuhiro; Matsuda, Kuniharu; Iguchi, Hirofumi

2012-10-01

White fluorescent OLED devices with a 10 nm thick blue-emitting layer and a 31 nm thick orange-emitting layer have been fabricated, where the blue-emitting layer is stacked on a hole transport layer. An interlayer was inserted between the two emitting layers. The thickness of the interlayer was changed among 0.3, 0.4, and 1.0 nm. White emission with CIE coordinates close to (0.33, 0.33) was observed from all the OLEDs. OLED with 0.3 nm thick interlayer gives the highest maximum luminous efficiency (11 cd/A), power efficiency (9 lm/W), and external quantum efficiency (5.02%). The external quantum efficiency becomes low with increasing the interlayer thickness from 0 nm to 1.0 nm. When the location of the blue- and orange-emitting layers is reversed, white emission was not obtained because of too weak blue emission. It is suggested that the electron-hole recombination zone decreases nearly exponentially with a distance from the hole transport layer.

Edge-terminated molybdenum disulfide with a 9.4-Å interlayer spacing for electrochemical hydrogen production

PubMed Central

Gao, Min-Rui; Chan, Maria K.Y.; Sun, Yugang

2015-01-01

Layered molybdenum disulfide has demonstrated great promise as a low-cost alternative to platinum-based catalysts for electrochemical hydrogen production from water. Research effort on this material has focused mainly on synthesizing highly nanostructured molybdenum disulfide that allows the exposure of a large fraction of active edge sites. Here we report a promising microwave-assisted strategy for the synthesis of narrow molybdenum disulfide nanosheets with edge-terminated structure and a significantly expanded interlayer spacing, which exhibit striking kinetic metrics with onset potential of −103 mV, Tafel slope of 49 mV per decade and exchange current density of 9.62 × 10−3 mA cm−2, performing among the best of current molybdenum disulfide catalysts. Besides benefits from the edge-terminated structure, the expanded interlayer distance with modified electronic structure is also responsible for the observed catalytic improvement, which suggests a potential way to design newly advanced molybdenum disulfide catalysts through modulating the interlayer distance. PMID:26138031

Revealing the preferred interlayer orientations and stackings of two-dimensional bilayer gallium selenide crystals.

PubMed

Li, Xufan; Basile, Leonardo; Yoon, Mina; Ma, Cheng; Puretzky, Alexander A; Lee, Jaekwang; Idrobo, Juan C; Chi, Miaofang; Rouleau, Christopher M; Geohegan, David B; Xiao, Kai

2015-02-23

Characterizing and controlling the interlayer orientations and stacking orders of two-dimensional (2D) bilayer crystals and van der Waals (vdW) heterostructures is crucial to optimize their electrical and optoelectronic properties. The four polymorphs of layered gallium selenide (GaSe) crystals that result from different layer stackings provide an ideal platform to study the stacking configurations in 2D bilayer crystals. Through a controllable vapor-phase deposition method, bilayer GaSe crystals were selectively grown and their two preferred 0° or 60° interlayer rotations were investigated. The commensurate stacking configurations (AA' and AB stacking) in as-grown bilayer GaSe crystals are clearly observed at the atomic scale, and the Ga-terminated edge structure was identified using scanning transmission electron microscopy. Theoretical analysis reveals that the energies of the interlayer coupling are responsible for the preferred orientations among the bilayer GaSe crystals. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Comparative Study of HfTa-based gate-dielectric Ge metal-oxide-semiconductor capacitors with and without AlON interlayer

NASA Astrophysics Data System (ADS)

Xu, J. P.; Zhang, X. F.; Li, C. X.; Chan, C. L.; Lai, P. T.

2010-04-01

The electrical properties and high-field reliability of HfTa-based gate-dielectric metal-oxide-semiconductor (MOS) devices with and without AlON interlayer on Ge substrate are investigated. Experimental results show that the MOS capacitor with HfTaON/AlON stack gate dielectric exhibits low interface-state/oxide-charge densities, low gate leakage, small capacitance equivalent thickness (˜1.1 nm), and high dielectric constant (˜20). All of these should be attributed to the blocking role of the ultrathin AlON interlayer against interdiffusions of Ge, Hf, and Ta and penetration of O into the Ge substrate, with the latter effectively suppressing the unintentional formation of unstable poor-quality low- k GeO x and giving a superior AlON/Ge interface. Moreover, incorporation of N into both the interlayer and high- k dielectric further improves the device reliability under high-field stress through the formation of strong N-related bonds.

Gallium arsenide single crystal solar cell structure and method of making

NASA Technical Reports Server (NTRS)

Stirn, Richard J. (Inventor)

1983-01-01

A production method and structure for a thin-film GaAs crystal for a solar cell on a single-crystal silicon substrate (10) comprising the steps of growing a single-crystal interlayer (12) of material having a closer match in lattice and thermal expansion with single-crystal GaAs than the single-crystal silicon of the substrate, and epitaxially growing a single-crystal film (14) on the interlayer. The material of the interlayer may be germanium or graded germanium-silicon alloy, with low germanium content at the silicon substrate interface, and high germanium content at the upper surface. The surface of the interface layer (12) is annealed for recrystallization by a pulsed beam of energy (laser or electron) prior to growing the interlayer. The solar cell structure may be grown as a single-crystal n.sup.+ /p shallow homojunction film or as a p/n or n/p junction film. A Ga(Al)AS heteroface film may be grown over the GaAs film.

Theory of optical absorption by interlayer excitons in transition metal dichalcogenide heterobilayers

NASA Astrophysics Data System (ADS)

Wu, Fengcheng; Lovorn, Timothy; MacDonald, A. H.

2018-01-01

We present a theory of optical absorption by interlayer excitons in a heterobilayer formed from transition metal dichalcogenides. The theory accounts for the presence of small relative rotations that produce a momentum shift between electron and hole bands located in different layers, and a moiré pattern in real space. Because of the momentum shift, the optically active interlayer excitons are located at the moiré Brillouin zone's corners, instead of at its center, and would have elliptical optical selection rules if the individual layers were translationally invariant. We show that the exciton moiré potential energy restores circular optical selection rules by coupling excitons with different center of mass momenta. A variety of interlayer excitons with both senses of circular optical activity, and energies that are tunable by twist angle, are present at each valley. The lowest energy exciton states are generally localized near the exciton potential energy minima. We discuss the possibility of using the moiré pattern to achieve scalable two-dimensional arrays of nearly identical quantum dots.

Moiré-pattern interlayer potentials in van der Waals materials in the random-phase approximation

NASA Astrophysics Data System (ADS)

Leconte, Nicolas; Jung, Jeil; Lebègue, Sébastien; Gould, Tim

2017-11-01

Stacking-dependent interlayer interactions are important for understanding the structural and electronic properties in incommensurable two-dimensional material assemblies where long-range moiré patterns arise due to small lattice constant mismatch or twist angles. Here we study the stacking-dependent interlayer coupling energies between graphene (G) and hexagonal boron nitride (BN) homo- and heterostructures using high-level random-phase approximation (RPA) ab initio calculations. Our results show that although total binding energies within LDA and RPA differ substantially by a factor of 200%-400%, the energy differences as a function of stacking configuration yield nearly constant values with variations smaller than 20%, meaning that LDA estimates are quite reliable. We produce phenomenological fits to these energy differences, which allows us to calculate various properties of interest including interlayer spacing, sliding energetics, pressure gradients, and elastic coefficients to high accuracy. The importance of long-range interactions (captured by RPA but not LDA) on various properties is also discussed. Parametrizations for all fits are provided.

Comparative study of the tribological behavior under hybrid lubrication of diamond-like carbon films with different adhesion interfaces

NASA Astrophysics Data System (ADS)

Costa, R. P. C.; Lima-Oliveira, D. A.; Marciano, F. R.; Lobo, A. O.; Corat, E. J.; Trava-Airoldi, V. J.

2013-11-01

This paper reports the influence of the adhesion interlayer between stainless steel and diamond-like carbon (DLC) films in two different contact conditions: in dry air and deionized water. The water was the liquid used to understand the mechanism and chemical reactions of the tribolayer formation under boundary lubrication. The effect of silicon and carbonitride adhesion interlayer was investigated on uncoated and coated DLC films. The results show that DLC/DLC pairs using carbonitride in air (30% RH) showed 60% less friction coefficient and wear less than three orders of magnitude than DLC/DLC pairs using silicon as interlayer. In deionized water, DLC/DLC pairs using carbonitride as interlayer showed 31% less friction coefficient when compared to DLC/DLC pairs with silicon. Raman related the chemical and structural changes in the DLC films during sliding in air and in the presence of water. Scratch tests showed a critical load of 14 N and 33 N in DLC films with silicon and carbonitride, respectively.

Interlayer shear behaviors of graphene-carbon nanotube network

NASA Astrophysics Data System (ADS)

Qin, Huasong; Liu, Yilun

2017-09-01

The interlayer shear resistance plays an important role in graphene related applications, and different mechanisms have been proposed to enhance its interlayer load capacity. In this work, we performed molecular dynamics (MD) simulations and theoretical analysis to study interlayer shear behaviors of three dimensional graphene-carbon (3D-GC) nanotube networks. The shear mechanical properties of carbon nanotubes (CNTs) crosslink with different diameters are obtained which is one order of magnitude larger than that of other types of crosslinks. Under shear loading, 3D-GC exhibits two failure modes, i.e., fracture of graphene sheet and failure of CNT crosslink, determined by the diameter of CNT crosslink, crosslink density, and length of 3D-GC. A modified tension-shear chain model is proposed to predict the shear mechanical properties and failure mode of 3D-GC, which agrees well with MD simulation results. The results presented in this work may provide useful insights for future development of high-performance 3D-GC materials.

Preparation, physicochemical characterisation and magnetic properties of Cu-Al layered double hydroxides with CO 32- and anionic surfactants with different alkyl chains in the interlayer

NASA Astrophysics Data System (ADS)

Trujillano, Raquel; Holgado, María Jesús; Pigazo, Fernando; Rives, Vicente

2006-03-01

Layered double hydroxides with the hydrotalcite-like structure, containing Cu(II) and Al(III) in the layers, and different alkyl sulphonates in the interlayer, have been prepared and characterised by powder X-ray diffraction, FT-IR spectroscopy, differential thermal analysis and thermogravimetric analysis. Their magnetic properties have been also studied. Except for the sample containing octadecanesulphonate in the interlayer, for which an excess of sulphonate exists, pure crystalline phases have been obtained in the other cases. Upon heating, combustion of the organic chain takes place at lower temperature than for the corresponding sodium salts. A two-dimensional antiferromagnetic behaviour is observed at 200 K in all samples containing intercalated sulphonate. The χT value is lower for the samples containing interlayer sulphonates (with layer-layer distances in the 21-31 Å range), than for a carbonate-containing analogue (basal spacing 7.51 Å).

[Bioimpedometry and its utilization in dialysis therapy].

PubMed

Lopot, František

2016-01-01

Measurement of living tissue impedance - bioimpedometry - started to be used in medicine some 50 years ago, first exclusively for estimation of extracellular and intracellular compartment volumes. Its most simple single frequency (50 kHz) version works directly with the measured impedance vector. Technically more sophisticated versions convert the measured impedance in values of volumes of different compartments of body fluids and calculate also principal markers of nutritional status (lean body mass, adipose tissue mass). The latest version specifically developed for application in dialysis patients includes body composition modelling and provides even absolute value of overhydration (excess fluid). Still in experimental phase is the bioimpedance exploitation for more precise estimation of residual glomerular filtration. Not yet standardized is also segmental bioimpedance measurement which should enable separate assessment of hydration status of the trunk segment and ultrafiltration capacity of peritoneum in peritoneal dialysis patients.Key words: assessment - bioimpedance - excess fluid - fluid status - glomerular filtration - haemodialysis - nutritional status - peritoneal dialysis.

Density-functional theory molecular dynamics simulations of a-HfO2/a-SiO2/SiGe and a-HfO2/a-SiO2/Ge with a-SiO2 and a-SiO suboxide interfacial layers

NASA Astrophysics Data System (ADS)

Chagarov, Evgueni A.; Kavrik, Mahmut S.; Fang, Ziwei; Tsai, Wilman; Kummel, Andrew C.

2018-06-01

Comprehensive Density-Functional Theory (DFT) Molecular Dynamics (MD) simulations were performed to investigate interfaces between a-HfO2 and SiGe or Ge semiconductors with fully-stoichiometric a-SiO2 or sub-oxide SiO interlayers. The electronic structure of the selected stacks was calculated with a HSE06 hybrid functional. Simulations were performed before and after hydrogen passivation of residual interlayer defects. For the SiGe substrate with Ge termination prior to H passivation, the stacks with a-SiO suboxide interlayer (a-HfO2/a-SiO/SiGe) demonstrate superior electronic properties and wider band-gaps than the stacks with fully coordinated a-SiO2 interlayers (a-HfO2/a-SiO2/SiGe). After H passivation, most of the a-HfO2/a-SiO2/SiGe defects are passivated. To investigate effect of random placement of Si and Ge atoms additional simulations with a randomized SiGe slab were performed demonstrating improvement of electronic structure. For Ge substrates, before H passivation, the stacks with a SiO suboxide interlayer (a-HfO2/a-SiO/Ge) also demonstrate wider band-gaps than the stacks with fully coordinated a-SiO2 interlayers (a-HfO2/a-SiO2/Ge). However, even for a-HfO2/a-SiO/Ge, the Fermi level is shifted close to the conduction band edge (CBM) consistent with Fermi level pinning. Again, after H passivation, most of the a-HfO2/a-SiO2/Ge defects are passivated. The stacks with fully coordinated a-SiO2 interlayers have much stronger deformation and irregularity in the semiconductor (SiGe or Ge) upper layers leading to multiple under-coordinated atoms which create band-edge states and decrease the band-gap prior to H passivation.

Formation of hydrotalcite in aqueous solutions and intercalation of ATP by anion exchange.

PubMed

Tamura, Hiroki; Chiba, Jun; Ito, Masahiro; Takeda, Takashi; Kikkawa, Shinichi; Mawatari, Yasuteru; Tabata, Masayoshi

2006-08-15

The formation reaction and the intercalation of adenosine triphosphate (ATP) were studied for hydrotalcite (HT), a layered double hydroxide (LDH) of magnesium and aluminum. Hydrotalcite with nitrate ions in the interlayer (HT-NO(3)) was formed (A) by dropwise addition of a solution of magnesium and aluminum nitrates (pH ca. 3) to a sodium hydroxide solution (pH ca. 14) until the pH decreased from 14 to 10 and (B) by dropwise addition of the NaOH solution to the solution of magnesium and aluminum nitrates with pH increasing from 3 to 10. The precipitate obtained with method B was contaminated with aluminum hydroxide and the crystallinity of the product was low, possibly because aluminum hydroxide precipitates at pH 4 or 5 and remains even after HT-NO(3) forms at pH above 8. With method A, however, the precipitate was pure HT-NO(3) with increased crystallinity, since the solubility of aluminum hydroxide at pH above and around 10 is high as dissolved aluminate anions are stable in this high pH region, and there was no aluminum hydroxide contamination. The formed HT-NO(3) had a composition of [Mg(0.71)Al(0.29)(OH)(2)](NO(3))(0.29).0.58H(2)O. To intercalate ATP anions into the HT-NO(3), HT-NO(3) was dispersed in an ATP solution at pH 7. It was found that the interlayer nitrate ions were completely exchanged with ATP anions by ion exchange, and the interlayer distance expanded almost twice with a free space distance of 1.2 nm. The composition of HT-ATP was established as [Mg(0.68)Al(0.32)(OH)(2)](ATP)(0.080)0.88H(2)O. The increased distance could be explained with a calculated molecular configuration of the ATP as follows: An ATP molecule is bound to an interlayer surface with the triphosphate group, the adenosine group bends owing to its bond angles and projects into the interlayer to a height of 1 nm, and the adenosine groups aligned in the interlayer support the interlayer distance.

Excessively High Hydration Volume May Not Be Associated With Decreased Risk of Contrast-Induced Acute Kidney Injury After Percutaneous Coronary Intervention in Patients With Renal Insufficiency.

PubMed

Liu, Yong; Li, Hualong; Chen, Shiqun; Chen, Jiyan; Tan, Ning; Zhou, Yingling; Liu, Yuanhui; Ye, Piao; Ran, Peng; Duan, Chongyang; Chen, Pingyan

2016-05-27

No well-defined protocols currently exist regarding the optimal rate and duration of normal saline administration to prevent contrast-induced acute kidney injury (CI-AKI) in patients with renal insufficiency. Hydration volume ratios (hydration volume/weight; HV/W) were calculated in 1406 patients with renal insufficiency (estimated glomerular filtration rate [eGFR], <90 mL/min per 1.73 m(2)) undergoing percutaneous coronary intervention (PCI) with routine speed hydration (1 or 0.5 mL/kg per hour). We investigated the relationship between hydration volume, risk of CI-AKI (increase in serum creatinine ≥0.5 mg/dL or 25% within 48-72 hours), and prognosis. Mean follow-up duration was 2.85±0.88 years. Individuals with higher HV/W were more likely to develop CI-AKI (quartiles: Q1, Q2, Q3, and Q4: 4.3%, 6.6%, 10.9%, and 15.0%, respectively; P<0.001). After adjusting 12 confounders, including age, sex, eGFR, anemia, emergent PCI, diabetes mellitus, chronic heart failure, diuretics, contrast volume, lesions, smoking status, and number of stents, multivariate analysis showed that a higher HV/W ratio was not associated with a decreased CI-AKI risk (Q2 vs Q1: adjusted odds ratio [OR], 1.13; Q3 vs Q1: adjusted OR, 1.51; Q4 vs Q1: adjusted OR, 1.87; all P>0.05) and even increased CI-AKI risk (HV/W >25 mL/kg: adjusted OR, 2.11; 95% CI, 1.24-3.59; P=0.006). Additionally, higher HV/W was significantly associated with an increased risk of death (Q4 vs Q1: adjusted hazard ratio, 3.44; 95% CI, 1.20-9.88; P=0.022). Excessively high hydration volume at routine speed might be associated with increased risk of CI-AKI and death post-PCI in patients with renal insufficiency. © 2016 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley Blackwell.

Interlayer coupling effects on Schottky barrier in the arsenene-graphene van der Waals heterostructures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xia, Congxin, E-mail: xiacongxin@htu.edu.cn; Xue, Bin; Wang, Tianxing

The electronic characteristics of arsenene-graphene van der Waals (vdW) heterostructures are studied by using first-principles methods. The results show that a linear Dirac-like dispersion relation around the Fermi level can be quite well preserved in the vdW heterostructures. Moreover, the p-type Schottky barrier (0.18 eV) to n-type Schottky barrier (0.31 eV) transition occurs when the interlayer distance increases from 2.8 to 4.5 Å, which indicates that the Schottky barrier can be tuned effectively by the interlayer distance in the vdW heterostructures.

Laser-Induced Fabrication of Metallic Interlayers and Patterns in Polyimide Films

NASA Technical Reports Server (NTRS)

Miner, Gilda A. (Inventor); Stoakley, Diane M. (Inventor); Gaddy, Gregory A. (Inventor); Koplitz, Brent D. (Inventor); Simpson, Steven M. (Inventor); Lynch, Michael F. (Inventor); Ruffner, Samuel C. (Inventor)

2010-01-01

Self-metallizing polyimide films are created by doping polyamic acid solutions with metallic ions and solubilizing agents. Upon creating a film, the film is exposed to coherent light for a specific time and then cured. The resulting film has been found to have a metallic surface layer and a metallic subsurface layer (interlayer). The layer separating the metallic layer has a uniform dispersion of small metal particulates within the polymer. The layer below the interlayer has larger metal particulates uniformly distributed within the polymer. By varying the intensity or time of exposure to the coherent light, three-dimensional control of metal formation within the film is provided.

Microscopic structure and properties of discrete water layer in Na-exchanged montmorillonite.

PubMed

Emmerich, Katja; Koeniger, Franz; Kaden, Heike; Thissen, Peter

2015-06-15

In this work, we focus on the atomic structure of the water interlayer of Na-exchanged montmorillonite. For two different surface charge densities, namely -0.086 and -0.172 C/m(2), the adsorption process in the presence of water is described by first principles calculations. We describe the interactions and forces for every water molecule entering the interlayer during the swelling process. In particular, the dielectric permittivity of the water interlayer is calculated. Finally, we confirm our results performing ab initio thermodynamics calculations leading to a wide range of realistic experimental scenarios. Copyright © 2015 Elsevier Inc. All rights reserved.

The nature of the interlayer interaction in bulk and few-layer phosphorus

DOE PAGES

Shulenburger, Luke; Baczewski, A. D.; Zhu, Z.; ...

2015-11-02

Sensitive dependence of the electronic structure on the number of layers in few-layer phosphorene raises a question about the true nature of the interlayer interaction in so-called van der Waals (vdW) solids . We performed quantum Monte Carlo calculations and found that the interlayer interaction in bulk black phosphorus and related few-layer phosphorene is associated with a significant charge redistribution that is incompatible with purely dispersive forces and not captured by density functional theory calculations with different vdW corrected functionals. Lastly, these findings confirm the necessity of more sophisticated treatment of nonlocal electron correlation in total energy calculations.

The Nature of the Interlayer Interaction in Bulk and Few-Layer Phosphorus.

PubMed

Shulenburger, L; Baczewski, A D; Zhu, Z; Guan, J; Tománek, D

2015-12-09

Sensitive dependence of the electronic structure on the number of layers in few-layer phosphorene raises a question about the true nature of the interlayer interaction in so-called "van der Waals (vdW) solids". We performed quantum Monte Carlo calculations and found that the interlayer interaction in bulk black phosphorus and related few-layer phosphorene is associated with a significant charge redistribution that is incompatible with purely dispersive forces and not captured by density functional theory calculations with different vdW corrected functionals. These findings confirm the necessity of more sophisticated treatment of nonlocal electron correlation in total energy calculations.

Reduced graphene oxide/molecular imprinted polymer-organic thin film transistor for amino acid detection

NASA Astrophysics Data System (ADS)

Halim, Nurul Farhanah AB.; Musa, Nur Hazwani; Zakaria, Zulkhairi; Von Schleusingen, Mubaraq; Ahmad, Mohd Noor; Derman, Nazree; Shakaff, Ali Yeon Md.

2017-03-01

This works reports the electrical performance of reduced graphene oxide (RGO)/Molecular imprinted polymer (MIP)- organic thin film transistor (OTFT) for amino-acid detection, serine. These biomimetic sensors consider MIP as man-tailored biomimetic recognition sites that play an important role in signal transduction. MIP provides recognition sites compatible with serine molecules was developed by dispersing serine with methylacrylate acid (MAA) as functional monomer and Ethylene glycol dimethylacrylate (EGDMA) as cross-linker. The imprinted polymeric were mixed with reduced graphene oxide to produced sensing layer for the sensor. RGO-MIP layer was introduced between source and drain of OTFT via spin coating as a detecting layer for serine molecules. RGO was introduced into MIP, to allow a highly conductive sensing material thus enhanced selectivity and sensitivity of the sensor. By analyzing the electrical performance of the sensors, the performances of OTFT sensor enhanced with RGO/MIP interlayer and OTFT sensor with MIP interlayer when exposed to serine analyte were obtained. The results showed that there were remarkable shifts of drain current (ID) obtained from OTFT sensor with RGO/MIP interlayer after exposed to serine analyte. Moreover, the sensitivity of OTFT sensor with RGO/MIP interlayer was nearly higher than the OTFT sensor with MIP interlayer. Hence, it proved that RGO successfully enhanced the sensing performance of OTFT sensor.

Two-Dimensional J eff = 1 / 2 Antiferromagnetic Insulator Unraveled from Interlayer Exchange Coupling in Artificial Perovskite Iridate Superlattices

DOE PAGES

Hao, Lin; Meyers, D.; Frederick, Clayton; ...

2017-07-14

We report an experimental investigation of the two-dimensional J eff=1/2 antiferromagnetic Mott insulator by varying the interlayer exchange coupling in [(SrIrO 3) 1, (SrTiO 3) m] (m=1, 2 and 3) superlattices. Although all samples exhibited an insulating ground state with long-range magnetic order, temperature-dependent resistivity measurements showed a stronger insulating behavior in the m = 2 and m = 3 samples than the m = 1 sample which displayed a clear kink at the magnetic transition. This difference indicates that the blocking effect of the excessive SrTiO 3 layer enhances the effective electron-electron correlation and strengthens the Mott phase. Themore » significant reduction of the Néel temperature from 150 K for m = 1 to 40 K for m = 2 demonstrates that the long-range order stability in the former is boosted by a substantial interlayer exchange coupling. Resonant x-ray magnetic scattering revealed that the interlayer exchange coupling has a switchable sign, depending on the SrTiO 3 layer number m, for maintaining canting-induced weak ferromagnetism. In conclusion, the nearly unaltered transition temperature between the m = 2 and the m = 3 demonstrated that we have realized a two-dimensional antiferromagnet at finite temperatures with diminishing interlayer exchange coupling.« less

Two-Dimensional J eff = 1 / 2 Antiferromagnetic Insulator Unraveled from Interlayer Exchange Coupling in Artificial Perovskite Iridate Superlattices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hao, Lin; Meyers, D.; Frederick, Clayton

We report an experimental investigation of the two-dimensional J eff=1/2 antiferromagnetic Mott insulator by varying the interlayer exchange coupling in [(SrIrO 3) 1, (SrTiO 3) m] (m=1, 2 and 3) superlattices. Although all samples exhibited an insulating ground state with long-range magnetic order, temperature-dependent resistivity measurements showed a stronger insulating behavior in the m = 2 and m = 3 samples than the m = 1 sample which displayed a clear kink at the magnetic transition. This difference indicates that the blocking effect of the excessive SrTiO 3 layer enhances the effective electron-electron correlation and strengthens the Mott phase. Themore » significant reduction of the Néel temperature from 150 K for m = 1 to 40 K for m = 2 demonstrates that the long-range order stability in the former is boosted by a substantial interlayer exchange coupling. Resonant x-ray magnetic scattering revealed that the interlayer exchange coupling has a switchable sign, depending on the SrTiO 3 layer number m, for maintaining canting-induced weak ferromagnetism. In conclusion, the nearly unaltered transition temperature between the m = 2 and the m = 3 demonstrated that we have realized a two-dimensional antiferromagnet at finite temperatures with diminishing interlayer exchange coupling.« less

PMMA interlayer-modulated memory effects by space charge polarization in resistive switching based on CuSCN-nanopyramids/ZnO-nanorods p-n heterojunction

PubMed Central

Cheng, Baochang; Zhao, Jie; Xiao, Li; Cai, Qiangsheng; Guo, Rui; Xiao, Yanhe; Lei, Shuijin

2015-01-01

Resistive switching (RS) devices are commonly believed as a promising candidate for next generation nonvolatile resistance random access memory. Here, polymethylmethacrylate (PMMA) interlayer was introduced at the heterointerface of p-CuSCN hollow nanopyramid arrays and n-ZnO nanorod arrays, resulting in a typical bipolar RS behavior. We propose the mechanism of nanostructure trap-induced space charge polarization modulated by PMMA interlayer. At low reverse bias, PMMA insulator can block charges through the heterointerface, and and trapped states are respectively created on both sides of PMMA, resulting in a high resistance state (HRS) due to wider depletion region. At high reverse bias, however, electrons and holes can cross PMMA interlayer by Fowler-Nordeim tunneling due to a massive tilt of energy band, and then inject into the traps of ZnO and CuSCN, respectively. and trapped states are created, resulting in the formation of degenerate semiconductors on both sides of PMMA. Therefore, quantum tunneling and space charge polarization lead to a low resistance state (LRS). At relatively high forward bias, subsequently, the trapped states of and are recreated due to the opposite injection of charges, resulting in a recovery of HRS. The introduction of insulating interlayer at heterointerface, point a way to develop next-generation nonvolatile memories. PMID:26648249

SnO2/Reduced Graphene Oxide Interlayer Mitigating the Shuttle Effect of Li-S Batteries.

PubMed

Hu, Nana; Lv, Xingshuai; Dai, Ying; Fan, Linlin; Xiong, Dongbin; Li, Xifei

2018-06-06

The short cycle life of lithium-sulfur batteries (LSBs) plagues its practical application. In this study, a uniform SnO 2 /reduced graphene oxide (denoted as SnO 2 /rGO) composite is successfully designed onto the commercial polypropylene separator for use of interlayer of LSBs to decrease the charge-transfer resistance and trap the soluble lithium polysulfides (LPSs). As a result, the assembled devices using the separator modified with the functional interlayer (SnO 2 /rGO) exhibit improved cycle performance; for instance, over 200 cycles at 1C, the discharge capacity of the cells reaches 734 mAh g -1 . The cells also display high rate capability, with the average discharge capacity of 541.9 mAh g -1 at 5C. Additionally, the mechanism of anchoring behavior of the SnO 2 /rGO interlayer was systematically investigated using density functional theory calculations. The results demonstrate that the improved performance is related to the ability of SnO 2 /rGO to effectively absorb S 8 cluster and LPS. The strong Li-O/Sn-S/O-S bonds and tight chemical adsorption between LPS and SnO 2 mitigate the shuttle effect of LSBs. This study demonstrates that engineering the functional interlayer of metal oxide and carbon materials in LSBs may be an easy way to improve their rate capacity and cycling life.

Efficient hybrid white organic light-emitting diodes with extremely long lifetime: the effect of n-type interlayer

PubMed Central

Liu, Baiquan; Wang, Lei; Xu, Miao; Tao, Hong; Zou, Jianhua; Gao, Dongyu; Lan, Linfeng; Ning, Honglong; Peng, Junbiao; Cao, Yong

2014-01-01

The effect of n-type interlayer in hybrid white organic light-emitting diodes (WOLEDs) has been systematically investigated by using various n-type materials. A new finding, that the triplet energy rather than electron mobility or hole-blocking ability of interlayer plays a more positive role in the performance of hybrid WOLEDs, is demonstrated. Based on the new finding, a more efficient n-type interlayer bis[2-(2-hydroxyphenyl)-pyridine] beryllium has been employed to realize a high-performance hybrid WOLED. The resulting device (without n-doping technology) exhibits low voltages (i.e., 2.8 V for 1 cd/m2, 3.9 V for 100 cd/m2) and low efficiency roll-off (i.e., 11.5 cd/A at 100 cd/m2 and 11.2 cd/A at 1000 cd/m2). At the display-relevant luminance of 100 cd/m2, a total power efficiency of 16.0 lm/W, a color rendering index of 73 and an extremely long lifetime of 12596265 h are obtained. Such superior results not only comprehensively indicate that the n-type materials are effective interlayers to develop high-performance hybrid WOLEDs but also demonstrate a significant step towards real commercialization in WOLEDs. PMID:25425090

Stacking sequence determines Raman intensities of observed interlayer shear modes in 2D layered materials – A general bond polarizability model

PubMed Central

Luo, Xin; Lu, Xin; Cong, Chunxiao; Yu, Ting; Xiong, Qihua; Ying Quek, Su

2015-01-01

2D layered materials have recently attracted tremendous interest due to their fascinating properties and potential applications. The interlayer interactions are much weaker than the intralayer bonds, allowing the as-synthesized materials to exhibit different stacking sequences, leading to different physical properties. Here, we show that regardless of the space group of the 2D materials, the Raman frequencies of the interlayer shear modes observed under the typical configuration blue shift for AB stacked materials, and red shift for ABC stacked materials, as the number of layers increases. Our predictions are made using an intuitive bond polarizability model which shows that stacking sequence plays a key role in determining which interlayer shear modes lead to the largest change in polarizability (Raman intensity); the modes with the largest Raman intensity determining the frequency trends. We present direct evidence for these conclusions by studying the Raman modes in few layer graphene, MoS2, MoSe2, WSe2 and Bi2Se3, using both first principles calculations and Raman spectroscopy. This study sheds light on the influence of stacking sequence on the Raman intensities of intrinsic interlayer modes in 2D layered materials in general, and leads to a practical way of identifying the stacking sequence in these materials. PMID:26469313

Stacking sequence determines Raman intensities of observed interlayer shear modes in 2D layered materials--A general bond polarizability model.

PubMed

Luo, Xin; Lu, Xin; Cong, Chunxiao; Yu, Ting; Xiong, Qihua; Quek, Su Ying

2015-10-15

2D layered materials have recently attracted tremendous interest due to their fascinating properties and potential applications. The interlayer interactions are much weaker than the intralayer bonds, allowing the as-synthesized materials to exhibit different stacking sequences, leading to different physical properties. Here, we show that regardless of the space group of the 2D materials, the Raman frequencies of the interlayer shear modes observed under the typical z(xx)z configuration blue shift for AB stacked materials, and red shift for ABC stacked materials, as the number of layers increases. Our predictions are made using an intuitive bond polarizability model which shows that stacking sequence plays a key role in determining which interlayer shear modes lead to the largest change in polarizability (Raman intensity); the modes with the largest Raman intensity determining the frequency trends. We present direct evidence for these conclusions by studying the Raman modes in few layer graphene, MoS2, MoSe2, WSe2 and Bi2Se3, using both first principles calculations and Raman spectroscopy. This study sheds light on the influence of stacking sequence on the Raman intensities of intrinsic interlayer modes in 2D layered materials in general, and leads to a practical way of identifying the stacking sequence in these materials.

Spin-triplet electron transport in hybrid superconductor heterostructures with a composite ferromagnetic interlayer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheyerman, A. E., E-mail: karen@hitech.cplire.ru; Constantinian, K. Y.; Ovsyannikov, G. A.

2015-06-15

Hybrid YBa{sub 2}Cu{sub 3}O{sub 7−x}/SrRuO{sub 3}/La{sub 0.7}Sr{sub 0.3}MnO{sub 3}/Au-Nb superconductor mesastructures with a composite manganite-ruthenate ferromagnetic interlayer are studied using electrophysical, magnetic, and microwave methods. The supercurrent in the mesastructure is observed when the interlayer thickness is much larger than the coherence length of ferromagnetic materials. The peak on the dependence of the critical current density on the interlayer material thickness corresponds to the coherence length, which is in qualitative agreement with theoretical predictions for a system with spit-triplet superconducting correlations. The magnetic-field dependence of the critical current is determined by penetration of magnetic flux quanta and by the magneticmore » domain structure, as well as by the field dependence of disorientation of the magnetization vectors of the layers in the composite magnetic interlayer. It is found that the supercurrent exists in magnetic fields two orders of magnitude stronger than the field corresponding to entry of a magnetic flux quantum into the mesastructure. The current-phase relation (CPR) of the supercurrent of mesastructures is investigated upon a change in the magnetic field from zero to 30 Oe; the ratio of the second CPR harmonic to the first, determined from the dependence of the Shapiro steps on the microwave radiation amplitude, does not exceed 50%.« less

Plasma boriding of a cobalt-chromium alloy as an interlayer for nanostructured diamond growth

NASA Astrophysics Data System (ADS)

Johnston, Jamin M.; Jubinsky, Matthew; Catledge, Shane A.

2015-02-01

Chemical vapor deposited (CVD) diamond coatings can potentially improve the wear resistance of cobalt-chromium medical implant surfaces, but the high cobalt content in these alloys acts as a catalyst to form graphitic carbon. Boriding by high temperature liquid baths and powder packing has been shown to improve CVD diamond compatibility with cobalt alloys. We use the microwave plasma-enhanced (PE) CVD process to deposit interlayers composed primarily of the borides of cobalt and chromium. The use of diborane (B2H6) in the plasma feedgas allows for the formation of a robust boride interlayer for suppressing graphitic carbon during subsequent CVD of nano-structured diamond (NSD). This metal-boride interlayer is shown to be an effective diffusion barrier against elemental cobalt for improving nucleation and adhesion of NSD coatings on a CoCrMo alloy. Migration of elemental cobalt to the surface of the interlayer is significantly reduced and undetectable on the surface of the subsequently-grown NSD coating. The effects of PECVD boriding are compared for a range of substrate temperatures and deposition times and are evaluated using glancing-angle X-ray diffraction (XRD), cross-sectional scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and micro-Raman spectroscopy. Boriding of CoCrMo results in adhered nanostructured diamond coatings with low surface roughness.

Triplet energy transfer and triplet exciton recycling in singlet fission sensitized organic heterojunctions

NASA Astrophysics Data System (ADS)

Hamid, Tasnuva; Yambem, Soniya D.; Crawford, Ross; Roberts, Jonathan; Pandey, Ajay K.

2017-08-01

Singlet exciton fission is a process where an excited singlet state splits into two triplets, thus leading to generation of multiple excitons per absorbed photon in organic semiconductors. Herein, we report a detailed exciton management approach for multiexciton harvesting over a broadband region of the solar spectrum in singlet fission sensitized organic photodiodes. Through systematic studies on the model cascade of pentacene/rubrene/C60, we found that efficient photocurrent generation from pentacene can still occur despite the presence of a >10nm thick interlayer of rubrene in between the pentacene/C60 heterojunction. Our results show that thin rubrene interlayers of thickness < 5 nm are effective in maintaining the delicate balance between two free charge generation channels that progress independently via the electron and hole transfer routes. The contribution to photocurrent from pentacene despite having a reasonably thick rubrene interlayer, that too with higher triplet energy (T1=1.12 eV) than pentacene (T1= 0.86 eV), makes its operation a rather interesting result. We discuss the role of rubrene interlayer film discontinuity, triplet exciton reflection from rubrene interlayer and triplet energy transfer from rubrene to pentacene layer followed by diffusion of triplet excitons through rubrene as plausible mechanisms that would enable triplet excitons from pentacene to generate significant photocurrent in a multilayer organic heterojunction.

Viscoelastic Waves Simulation in a Blocky Medium with Fluid-Saturated Interlayers Using High-Performance Computing

NASA Astrophysics Data System (ADS)

Sadovskii, Vladimir; Sadovskaya, Oxana

2017-04-01

A thermodynamically consistent approach to the description of linear and nonlinear wave processes in a blocky medium, which consists of a large number of elastic blocks interacting with each other via pliant interlayers, is proposed. The mechanical properties of interlayers are defined by means of the rheological schemes of different levels of complexity. Elastic interaction between the blocks is considered in the framework of the linear elasticity theory [1]. The effects of viscoelastic shear in the interblock interlayers are taken into consideration using the Pointing-Thomson rheological scheme. The model of an elastic porous material is used in the interlayers, where the pores collapse if an abrupt compressive stress is applied. On the basis of the Biot equations for a fluid-saturated porous medium, a new mathematical model of a blocky medium is worked out, in which the interlayers provide a convective fluid motion due to the external perturbations. The collapse of pores is modeled within the generalized rheological approach, wherein the mechanical properties of a material are simulated using four rheological elements. Three of them are the traditional elastic, viscous and plastic elements, the fourth element is the so-called rigid contact [2], which is used to describe the behavior of materials with different resistance to tension and compression. Thermodynamic consistency of the equations in interlayers with the equations in blocks guarantees fulfillment of the energy conservation law for a blocky medium in a whole, i.e. kinetic and potential energy of the system is the sum of kinetic and potential energies of the blocks and interlayers. As a result of discretization of the equations of the model, robust computational algorithm is constructed, that is stable because of the thermodynamic consistency of the finite difference equations at a discrete level. The splitting method by the spatial variables and the Godunov gap decay scheme are used in the blocks, the dissipationless finite difference Ivanov scheme is applied in the interlayers. The parallel program is designed, using the MPI technology. By means of this software, nonlinear wave processes in the case of initial rotation of the central block in a rock mass as well as in the case of concentrated couple stress load, applied at the boundary of a rock mass, are analyzed. Results of computations on the multiprocessor computer systems demonstrate the strong anisotropy of a blocky medium. This work was supported by the Complex Fundamental Research Program no. II.2P "Integration and Development" of Siberian Branch of the Russian Academy of Sciences. References 1. Sadovskii V.M., Sadovskaya O.V. Modeling of Elastic Waves in a Blocky Medium Based on Equations of the Cosserat Continuum // Wave Motion. 2015. V. 52. P. 138-150. 2. Sadovskaya O., Sadovskii V. Mathematical Modeling in Mechanics of Granular Materials. Ser.: Advanced Structured Materials, V. 21. Heidelberg - New York - Dordrecht - London, Springer, 2012. 390 p.

Comparison of total body water estimates from O-18 and bioelectrical response prediction equations

NASA Technical Reports Server (NTRS)

Barrows, Linda H.; Inners, L. Daniel; Stricklin, Marcella D.; Klein, Peter D.; Wong, William W.; Siconolfi, Steven F.

1993-01-01

Identification of an indirect, rapid means to measure total body water (TBW) during space flight may aid in quantifying hydration status and assist in countermeasure development. Bioelectrical response testing and hydrostatic weighing were performed on 27 subjects who ingested O-18, a naturally occurring isotope of oxygen, to measure true TBW. TBW estimates from three bioelectrical response prediction equations and fat-free mass (FFM) were compared to TBW measured from O-18. A repeated measures MANOVA with post-hoc Dunnett's Test indicated a significant (p less than 0.05) difference between TBW estimates from two of the three bioelectrical response prediction equations and O-18. TBW estimates from FFM and the Kushner & Schoeller (1986) equation yielded results that were similar to those given by O-18. Strong correlations existed between each prediction method and O-18; however, standard errors, identified through regression analyses, were higher for the bioelectrical response prediction equations compared to those derived from FFM. These findings suggest (1) the Kushner & Schoeller (1986) equation may provide a valid measure of TBW, (2) other TBW prediction equations need to be identified that have variability similar to that of FFM, and (3) bioelectrical estimates of TBW may prove valuable in quantifying hydration status during space flight.

Dehydration at admission increased the need for dialysis in hemolytic uremic syndrome children.

PubMed

Balestracci, Alejandro; Martin, Sandra Mariel; Toledo, Ismael; Alvarado, Caupolican; Wainsztein, Raquel Eva

2012-08-01

Oligoanuric forms of postdiarrheal hemolytic uremic syndrome (D+ HUS) usually have more severe acute stage and higher risk of chronic sequelae than nonoligoanuric forms. During the diarrheal phase, gastrointestinal losses could lead to dehydration with pre-renal injury enhancing the risk of oligoanuric D+ HUS. Furthermore, it had been shown that intravenous volume expansion during the prodromal phase could decrease the frequency of oligoanuric renal failure. Thus, we performed this retrospective study to determine whether dehydration on admission is associated with increased need for dialysis in D+ HUS patients. Data from 137 children was reviewed, which were divided into two groups according to their hydration status at admission: normohydrated (n = 86) and dehydrated (n = 51). Laboratory parameters of the dehydrated patients reflected expected deteriorations (higher urea, higher hematocrit and lower sodium, bicarbonate, and pH) than normohydrated ones. Likewise, the dehydrated group had a higher rate of vomiting and need for dialysis (70.6 versus 40.7 %, p = 0.0007). Our data suggests that dehydration at hospital admission might represent a concomitant factor aggravating the intrinsic renal disease in D+ HUS patients increasing the need for dialysis. Therefore, the early recognition of patients at risk of D+ HUS is encouraged to guarantee a well-hydrated status.

Polysulfide intercalated layered double hydroxides for metal capture applications

DOEpatents

Kanatzidis, Mercouri G.; Ma, Shulan

2017-04-04

Polysulfide intercalated layered double hydroxides and methods for their use in vapor and liquid-phase metal capture applications are provided. The layered double hydroxides comprise a plurality of positively charged host layers of mixed metal hydroxides separated by interlayer spaces. Polysulfide anions are intercalated in the interlayer spaces.

Cost-effectiveness and performance of overlay systems in Illinois, volume 1 : effectiveness assessment of HMA overlay interlayer systems used to retard reflective cracking.

DOT National Transportation Integrated Search

2009-05-01

This project evaluated the ability of interlayer systems used in HMA overlays to retard reflective cracking. Field : crack surveys and forensic investigation, including video imaging and ground penetrating radar surveys as well : as laboratory testin...

Cost-effectiveness and performance of overlay systems in Illinois, volume 2 : guidelines for interlayer system selection decision when used in HMA overlays.

DOT National Transportation Integrated Search

2009-05-01

In an effort to control reflective cracking in hot-mix asphalt (HMA) overlays placed over Portland Cement : Concrete (PCC) pavements, several reflective crack control (RCC) systems, including interlayer systems, : have been used. However, the cost-ef...

A Review of Battle Damage Prediction and Vulnerability Reduction Methods

DTIC Science & Technology

2010-10-01

monolithic constructions. Bahei-El-Din and Dvorak [38] showed that the use of a polyurethane or polyurea interlayer used in a sandwich plate in...sandwich plates reinforced with polyurethane/ polyurea interlayers under blast loads. Journal of Sandwich Structures and Materials 9 (3) 261–281. 39

Policy statement—Climatic heat stress and exercising children and adolescents.

PubMed

Bergeron, Michael F; Devore, Cynthia; Rice, Stephen G

2011-09-01

Results of new research indicate that, contrary to previous thinking, youth do not have less effective thermoregulatory ability, insufficient cardiovascular capacity, or lower physical exertion tolerance compared with adults during exercise in the heat when adequate hydration is maintained. Accordingly, besides poor hydration status, the primary determinants of reduced performance and exertional heat-illness risk in youth during sports and other physical activities in a hot environment include undue physical exertion, insufficient recovery between repeated exercise bouts or closely scheduled same-day training sessions or rounds of sports competition, and inappropriately wearing clothing, uniforms, and protective equipment that play a role in excessive heat retention. Because these known contributing risk factors are modifiable, exertional heat illness is usually preventable. With appropriate preparation, modifications, and monitoring, most healthy children and adolescents can safely participate in outdoor sports and other physical activities through a wide range of challenging warm to hot climatic conditions.

S100A8 and S100A9 Are Induced by Decreased Hydration in the Epidermis and Promote Fibroblast Activation and Fibrosis in the Dermis.

PubMed

Zhong, Aimei; Xu, Wei; Zhao, Jingling; Xie, Ping; Jia, Shengxian; Sun, Jiaming; Galiano, Robert D; Mustoe, Thomas A; Hong, Seok J

2016-01-01

The most critical function of the epidermis is to prevent water loss and maintain skin homeostasis. Disruption of the functional skin barrier causes delayed wound healing, hypertrophic scarring, and many skin diseases. Herein, we show that reduced hydration increases the expression of S100 protein family members, S100A8/S100A9, in stratified keratinocyte culture and human ex vivo skin culture. Immunohistological analyses show that S100A8/A9 are highly expressed in the epidermis of human hypertrophic scar and keloid tissues. Reduced hydration demonstrates activation of fibroblasts in the keratinocyte-fibroblast co-culture. In contrast, knockdown of S100A8 or S100A9 by RNA interference in keratinocytes failed to activate fibroblasts. Pretreatment with pharmacological blockers of S100A8/A9 receptors, Toll-like receptor 4 and receptor for advanced glycation end products, inhibits fibroblast activation induced by recombinant S100A8/A9 proteins. Moreover, we observe that local delivery of S100A8 protein results in a marked increase in hypertrophic scarring in the in vivo rabbit ear scar model. Our results indicate that hydration status promotes fibroblast activation and fibrosis by directly affecting the expression of inflammatory signaling in keratinocytes, thereby strongly suggesting S100A8/A9 to be novel targets in preventing scarring. Copyright © 2016 American Society for Investigative Pathology. Published by Elsevier Inc. All rights reserved.

Study of composite thin films for applications in high density data storage

NASA Astrophysics Data System (ADS)

Yuan, Hua

Granular Co-alloy + oxide thin films are currently used as the magnetic recording layer of perpendicular media in hard disk drives. The microstructure of these films is composed mainly of fine (7--10 nm) magnetic grains physically surrounded by oxide phases, which produce magnetic isolation of the grains. As a result, the magnetic switching volume is maintained as small as the physical grain size. Consequently, ample number of magnetic switching units can be obtained in one recording bit, in other words, higher signal to noise ratios (SNR) can be achieved. Therefore, a good understanding and control of the microstructure of the films is very important for high areal density magnetic recording media. Interlayers and seedlayers play important roles in controlling the microstructure in terms of grain size, grain size distribution, oxide segregation and orientation dispersion of the crystallographic texture. Developing novel interlayers or seedlayers with smaller grain size is a key approach to produce smaller grain size in the recording layer. This study focuses on how to achieve smaller grain sizes in the recording layer through novel interlayer/seedlayer materials and processes. It also discusses the resulting microstructure in smaller-grain-size thin films. Metal + oxide (e.g. Ru + SiO2) composite thin films were chosen as interlayer and seedlayer materials due to their unique segregated microstructure. Such layers can be grown epitaxially on top of fcc metal seedlayers with good orientation. It can also provide an epitaxial growth template for the subsequent magnetic layer (recording layer). The metal and oxide phases in the composite thin films are immiscible. The final microstructure of the interlayer depends on factors, such as, sputtering pressure, oxide species, oxide volume fraction, thickness, alloy composition, temperature etc. Moreover, it has been found that the microstructure of the composite thin films is affected mostly by two important factors---oxide volume fraction and sputtering pressure. The latter affects grain size and grain segregation through surface-diffusion modification and the self-shadowing effect. The composite Ru + oxide interlayers were found to have various microstructures under various sputtering conditions. Four characteristic microstructure zones can be identified as a function of oxide volume fraction and sputtering pressure---"percolated" (A), "maze" (T), "granular" (B) and "embedded" (C), based on which, a new structural zone model (SZM) is established for composite thin films. The granular microstructure of zone B is of particular interest for recording media application. The grain size of interlayers is a strong function of pressure, oxide species and oxide volume fraction. Magnetic layers grown on top of these interlayers were found to be significantly affected by the interlayer microstructure. One-to-one grain epitaxial growth is very difficult to achieve when the grain size is too small. As a result, the magnetic properties of smaller grain size magnetic layers deteriorate due to poor growth. This presents a huge challenge to high areal density magnetic recording media. A novel approach of Ar-ion etched Ru seedlayer, which can improve epitaxy between interlayer and magnetic layer is proposed. This method produces interlayer thin films of: (1) smaller grain size and higher nucleation density due to both a rougher seedlayer surface and an oxide addition in the interlayer; (2) good (00.2) texture due to the growth on top of the low pressure deposited Ru seedlayer; (3) dome-shape grain morphology due to the high pressure deposition. Therefore, a significant Ru grain size reduction with enhanced granular morphology and improved grain-to-grain epitaxy with the magnetic layer was achieved. High resolution transmission electron microscopy (TEM) techniques, such as, electron energy loss spectroscopy (EELS), energy-filtered TEM (EFTEM), energy-dispersive X-ray spectroscopy (EDS) and mapping, and high angle annular dark field (HAADF) imaging have been utilized to investigate elemental distribution and grain morphology in composite magnetic thin films of different grain sizes. An oxygen-rich grain shell of about 0.5 ˜ 1 nm thickness is often observed for most media with different grain sizes. Reducing the grain size increases surface to volume ratio. With more surface area, smaller grains are more vulnerable to oxidization, resulting in even greater influence of the oxide on the magnetic properties of the grains.

Which Frail Older People Are Dehydrated? The UK DRIE Study

PubMed Central

Bunn, Diane K.; Downing, Alice; Jimoh, Florence O.; Groves, Joyce; Free, Carol; Cowap, Vicky; Potter, John F.; Hunter, Paul R.; Shepstone, Lee

2016-01-01

Background: Water-loss dehydration in older people is associated with increased mortality and disability. We aimed to assess the prevalence of dehydration in older people living in UK long-term care and associated cognitive, functional, and health characteristics. Methods: The Dehydration Recognition In our Elders (DRIE) cohort study included people aged 65 or older living in long-term care without heart or renal failure. In a cross-sectional baseline analysis, we assessed serum osmolality, previously suggested dehydration risk factors, general health, markers of continence, cognitive and functional health, nutrition status, and medications. Univariate linear regression was used to assess relationships between participant characteristics and serum osmolality, then associated characteristics entered into stepwise backwards multivariate linear regression. Results: DRIE included 188 residents (mean age 86 years, 66% women) of whom 20% were dehydrated (serum osmolality >300 mOsm/kg). Linear and logistic regression suggested that renal, cognitive, and diabetic status were consistently associated with serum osmolality and odds of dehydration, while potassium-sparing diuretics, sex, number of recent health contacts, and bladder incontinence were sometimes associated. Thirst was not associated with hydration status. Conclusions: DRIE found high prevalence of dehydration in older people living in UK long-term care, reinforcing the proposed association between cognitive and renal function and hydration. Dehydration is associated with increased mortality and disability in older people, but trials to assess effects of interventions to support healthy fluid intakes in older people living in residential care are needed to enable us to formally assess causal direction and any health benefits of increasing fluid intakes. PMID:26553658

Hydration Status in US Military Officer Students.

PubMed

Rogers, Reva; Cole, Renee

2016-01-01

Relocation from a cool to a hot climate is a frequent occurrence in military service. Acclimatization requires time and exposure to heat. Nonacclimatized individuals frequently consume inadequate fluid leading to hypohydration, which can quickly result in dehydration with increased risk of heat illness/injury. This descriptive cross-sectional study assessed the hydration status of 196 officers attending the US Army Medical Department's Officer Basic Course (67%) or Captain's Career Course (33%) in San Antonio, Texas, prior to taking the Army Physical Fitness Test (APFT). Consenting Soldiers provided a first morning void urine sample and demographic survey (age, rank, sex, previous geographic location, etc) prior to the APFT. Height, weight, and APFT event scores were collected from a subject-coded, APFT scorecard without personal information data. Binary logistic regression was performed to identify variables that contribute to predicting hypohydration status. The sample population was 54% male, a mean age of 30 years, 5.2 years of military service, and a mean body mass index of 25 kg/m². Nearly one-third met the criteria for hypohydration (≥1.02 urine specific gravity). Soldiers who relocated from a cool environment within 9 days of taking the APFT had 2.1 higher odds of being hypohydrated compared with individuals who had resided in a hot environment for more than 9 days. Women had a 0.5 lower odds of being hypohydrated as compared to males. Significantly more Soldiers were hypohydrated on Monday compared to those tested on Tuesday (33% vs 16%, P=.004). Given these findings, the authors provided 5 recommendations to reduce the number of Soldiers exercising in a hypohydrated state.

Interlayer tunneling in a strongly correlated electron-phonon system

NASA Astrophysics Data System (ADS)

Mierzejewski, M.; Zieliński, J.

1996-10-01

We discuss the role of interlayer tunneling for superconducting properties of strongly correlated (U-->∞ limit) two-layer Hubbard model coupled to phonons. Strong correlations are taken into account within the mean-field approximation for auxiliary boson fields. To consider phonon-mediated and interlayer tunneling contribution to superconductivity on equal footing we incorporate the tunneling term into the generalized Eliashberg equations. This leads to the modification of the phonon-induced pairing kernel and implies a pronounced enhancement of the superconducting transition temperature in the d-wave channel for moderate doping. In numerical calculations the two-dimensional band structure has been explicitly taken into account. The relevance of our results for high-temperature superconductors is briefly discussed.

Layer Anti-Ferromagnetism on Bilayer Honeycomb Lattice

PubMed Central

Tao, Hong-Shuai; Chen, Yao-Hua; Lin, Heng-Fu; Liu, Hai-Di; Liu, Wu-Ming

2014-01-01

Bilayer honeycomb lattice, with inter-layer tunneling energy, has a parabolic dispersion relation, and the inter-layer hopping can cause the charge imbalance between two sublattices. Here, we investigate the metal-insulator and magnetic phase transitions on the strongly correlated bilayer honeycomb lattice by cellular dynamical mean-field theory combined with continuous time quantum Monte Carlo method. The procedures of magnetic spontaneous symmetry breaking on dimer and non-dimer sites are different, causing a novel phase transition between normal anti-ferromagnet and layer anti-ferromagnet. The whole phase diagrams about the magnetism, temperature, interaction and inter-layer hopping are obtained. Finally, we propose an experimental protocol to observe these phenomena in future optical lattice experiments. PMID:24947369

Diamond Composite Films for Protective Coatings on Metals and Method of Formation

NASA Technical Reports Server (NTRS)

Ong, Tiong P. (Inventor); Shing, Yuh-Han (Inventor)

1997-01-01

Composite films consisting of diamond crystallites and hard amorphous films such as diamond-like carbon, titanium nitride, and titanium oxide are provided as protective coatings for metal substrates against extremely harsh environments. A composite layer having diamond crystallites and a hard amorphous film is affixed to a metal substrate via an interlayer including a bottom metal silicide film and a top silicon carbide film. The interlayer is formed either by depositing metal silicide and silicon carbide directly onto the metal substrate, or by first depositing an amorphous silicon film, then allowing top and bottom portions of the amorphous silicon to react during deposition of the diamond crystallites, to yield the desired interlayer structure.

Surface modification of a polyimide gate insulator with an yttrium oxide interlayer for aqueous-solution-processed ZnO thin-film transistors.

PubMed

Jang, Kwang-Suk; Wee, Duyoung; Kim, Yun Ho; Kim, Jinsoo; Ahn, Taek; Ka, Jae-Won; Yi, Mi Hye

2013-06-11

We report a simple approach to modify the surface of a polyimide gate insulator with an yttrium oxide interlayer for aqueous-solution-processed ZnO thin-film transistors. It is expected that the yttrium oxide interlayer will provide a surface that is more chemically compatible with the ZnO semiconductor than is bare polyimde. The field-effect mobility and the on/off current ratio of the ZnO TFT with the YOx/polyimide gate insulator were 0.456 cm(2)/V·s and 2.12 × 10(6), respectively, whereas the ZnO TFT with the polyimide gate insulator was inactive.

Nickel hydroxide electrode. 3: Thermogravimetric investigations of nickel (II) hydroxides

NASA Technical Reports Server (NTRS)

Dennstedt, W.; Loeser, W.

1982-01-01

Water contained in Ni hydroxide influences its electrochemical reactivity. The water content of alpha and beta Ni hydroxides is different with respect to the amount and bond strength. Thermogravimetric experiments show that the water of the beta Ni hydroxides exceeding the stoichiometric composition is completely removed at 160 deg. The water contained in the interlayers of the beta hydroxide, however, is removed only at higher temperatures, together with the water originating from the decomposition of the hydroxide. These differences are attributed to the formation of II bonds within the interlayers and between interlayers and adjacent main layers. An attempt is made to explain the relations between water content and the oxidizability of the Ni hydroxides.

Frictional Magneto-Coulomb Drag in Graphene Double-Layer Heterostructures.

PubMed

Liu, Xiaomeng; Wang, Lei; Fong, Kin Chung; Gao, Yuanda; Maher, Patrick; Watanabe, Kenji; Taniguchi, Takashi; Hone, James; Dean, Cory; Kim, Philip

2017-08-04

Coulomb interaction between two closely spaced parallel layers of conductors can generate the frictional drag effect by interlayer Coulomb scattering. Employing graphene double layers separated by few-layer hexagonal boron nitride, we investigate density tunable magneto- and Hall drag under strong magnetic fields. The observed large magnetodrag and Hall-drag signals can be related with Laudau level filling status of the drive and drag layers. We find that the sign and magnitude of the drag resistivity tensor can be quantitatively correlated to the variation of magnetoresistivity tensors in the drive and drag layers, confirming a theoretical formula for magnetodrag in the quantum Hall regime. The observed weak temperature dependence and ∼B^{2} dependence of the magnetodrag are qualitatively explained by Coulomb scattering phase-space argument.

Effect of hydration on plasma vasopressin, renin, and aldosterone responses to head-up tilt

NASA Technical Reports Server (NTRS)

Harrison, M. H.; Geelen, G.; Keil, L. C.; Wade, C. A.; Hill, L. C.

1986-01-01

If plasma vasopressin (PVP), plasma renin (PRA), and plasma aldosterone (PA) responses to change in posture are mediated only by alterations in intrathoracic baroreceptor activity hydration status should have minimal influence on these responses. To test this hypothesis, six male subjects underwent 45 min of 70 deg head-up tilt (HUT) following 26 h dehydration, and again, 105 min later, following rehydration. Compared with preceding supine hydrated control values, PVP, PRA, and PA increased (p less than 0.001) during dehydrated HUT, but only PVP and PRA increased during rehydrated HUT (p less than 0.001). The dissociation during rehydrated HUT of PRA and PA may have been related more to the reduction (p less than 0.001) in plasma potassium concentration than to the accompanying decrease (p less than 0.001) in plasma osmolality and sodium concentration. Although increases in PVP and PRA during HUT were attenuated (p less than 0.01) following rehydration, this attenuation was associated with the absence of symptoms of overt hypotension following rehydration. However, since rehydration did not abolish the increases in PVP and PRA induced by HUT, it is concluded that the present observations support the concept of intrathoracic baroreceptor involvement in the regulation of vasopressin secretion and renin release.

Tilted Dirac Cone Effect on Interlayer Magnetoresistance in α-(BEDT-TTF)2I3

NASA Astrophysics Data System (ADS)

Tajima, Naoya; Morinari, Takao

2018-04-01

We report the effect of Dirac cone tilting on interlayer magnetoresistance in α-(BEDT-TTF)2I3, which is a Dirac semimetal under pressure. Fitting of the experimental data by the theoretical formula suggests that the system is close to a type-II Dirac semimetal.