Science.gov

Sample records for ion irradiation created

  1. Graphitic nanostripes in silicon carbide surfaces created by swift heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Ochedowski, Oliver; Osmani, Orkhan; Schade, Martin; Bussmann, Benedict Kleine; Ban-D'Etat, Brigitte; Lebius, Henning; Schleberger, Marika

    2014-06-01

    The controlled creation of defects in silicon carbide represents a major challenge. A well-known and efficient tool for defect creation in dielectric materials is the irradiation with swift (Ekin≥500 keV/amu) heavy ions, which deposit a significant amount of their kinetic energy into the electronic system. However, in the case of silicon carbide, a significant defect creation by individual ions could hitherto not be achieved. Here we present experimental evidence that silicon carbide surfaces can be modified by individual swift heavy ions with an energy well below the proposed threshold if the irradiation takes place under oblique angles. Depending on the angle of incidence, these grooves can span several hundreds of nanometres. We show that our experimental data are fully compatible with the assumption that each ion induces the sublimation of silicon atoms along its trajectory, resulting in narrow graphitic grooves in the silicon carbide matrix.

  2. Graphitic nanostripes in silicon carbide surfaces created by swift heavy ion irradiation.

    PubMed

    Ochedowski, Oliver; Osmani, Orkhan; Schade, Martin; Bussmann, Benedict Kleine; Ban-d'Etat, Brigitte; Lebius, Henning; Schleberger, Marika

    2014-06-06

    The controlled creation of defects in silicon carbide represents a major challenge. A well-known and efficient tool for defect creation in dielectric materials is the irradiation with swift (E(kin) ≥ 500 keV/amu) heavy ions, which deposit a significant amount of their kinetic energy into the electronic system. However, in the case of silicon carbide, a significant defect creation by individual ions could hitherto not be achieved. Here we present experimental evidence that silicon carbide surfaces can be modified by individual swift heavy ions with an energy well below the proposed threshold if the irradiation takes place under oblique angles. Depending on the angle of incidence, these grooves can span several hundreds of nanometres. We show that our experimental data are fully compatible with the assumption that each ion induces the sublimation of silicon atoms along its trajectory, resulting in narrow graphitic grooves in the silicon carbide matrix.

  3. Hillocks created for amorphizable and non-amorphizable ceramics irradiated with swift heavy ions: TEM study.

    PubMed

    Ishikawa, N; Taguchi, T; Okubo, N

    2017-11-03

    In a previous study, we found that hillocks (i.e. surface ion tracks) can be imaged using transmission electron microscopy (TEM) by irradiating thin CeO2 samples with swift heavy ions (SHI) at oblique incidence. In the present study, the same TEM method is applied to Y3Fe5O12 (YIG) and three fluorides (CaF2, SrF2 and BaF2) for observing hillocks. For YIG, which is one of the amorphizable materials, hillocks are found to have amorphous features consistent with amorphous features of ion tracks. For the fluorides, it is found that the hillocks do not exhibit amorphous features, and they are composed of nanocrystallites. Although hillocks for YIG and CaF2 exhibit different crystallographic features, hillock diameter agrees with the molten region diameter predicted by the thermal spike model for both materials. It is found that for YIG the hillock diameter is comparable to the ion track diameter, whereas for the fluorides it is always larger than the ion track diameter. The present result shows the existence of the velocity effect for ion track diameter in CaF2. It is also found that for fluorides both hillock and ion track diameters vary in the order of cation mass (i.e. CaF2 < SrF2 < BaF2). The above results of hillocks and ion tracks for SHI-irradiated fluorides can be consistently interpreted within the framework of the thermal spike model, if melting and successive recrystallization are assumed.

  4. Modification of the electrical and optical properties of polymers. [ion irradiation to create texture

    NASA Technical Reports Server (NTRS)

    Mirtich, M. J.; Sovey, J. S. (Inventor)

    1980-01-01

    An electron bombardment argon ion source is used to form textured surfaces on polymide and fluorinated ethylene propylene polymers. This treatment improves the optical and electrical properties so that these polymers may be used in industrial and space applications.

  5. 200 MeV Ag +15 ion irradiation created columnar defects and enhanced critical current density of La-2125 type superconducting thin films

    NASA Astrophysics Data System (ADS)

    Mavani, K. R.; Rana, D. S.; Rayaprol, S.; Parmar, R. N.; Kuberkar, D. G.; Ravi Kumar; Tonouchi, M.; John, J.; Nagarajan, R.

    2007-05-01

    We have deposited c-axis oriented thin films of La 1.5Dy 0.5CaBa 2Cu 5O z (La-2125) tetragonal superconductor on LaAlO 3(001) substrates by pulsed laser deposition. These films were irradiated with 200 MeV Ag +15 ions. Atomic force microscopy and elastic recoil detection analysis indicate that the irradiation has created columnar defects through the entire thickness (2000 Å) of these films. With ion irradiation up to 1×10 11 ions/cm 2, the critical current density ( Jc(H)) enhances by fivefold, which is attributed to the augmented flux pinning by the columnar defects. A further increase in irradiation to 1×10 12 ions/cm 2 causes reduction in Jc(H) due to distorted morphology of the film. Our work shows that the enhancement in Jc(H) of the irradiated La-2125 film is comparable to that in irradiated RE-123 (RE = rare earth ion). Also, as the La-2125 type films have greater chemical stability than RE-123, La-2125 type superconductors are potential candidates for applications. It is interesting to note that there are partial flux jumps observed to occur symmetrically in the magnetic hysteresis of irradiated La-2125 thin films with enhanced Jc(H).

  6. Cadmium Nanowire Formation Induced by Ion Irradiation

    SciTech Connect

    Jiang, Weilin; Weber, William J.; Wang, Chong M.; Young, James S.; Boatner, Lynn A.; Lian, Jie; Wang, Lumin; Ewing, Rodney C.

    2005-07-04

    One-dimensional nanostructures, such as nanowires, of semiconductors and metals are of great technological interest due to their potential for many advanced technology applications. Utilization of these materials versus their bulk counterparts will not only allow for device miniaturisation, but also may improve device performance or create new functions. Here we report a novel method for the synthesis of crystalline Cd-nanowires without involving either templates or a “seeded” structure. Ion irradiation at low temperatures (≤ 295 K) has been used to induce material decomposition and phase segregation in a cadmium niobate pyrochlore (Cd2Nb2O7) wafer. During the formation and rupture of the gas-filled blisters in the material, soft metallic Cd is extruded/extracted as nanowires through pores in the exfoliated layer. The entire process may be readily controlled by changing the ion irradiation conditions (e.g., ion species, dose and energy) with minimal thermal constraints.

  7. Study of a High-Yield Cellulase System Created by Heavy-Ion Irradiation-Induced Mutagenesis of Aspergillus niger and Mixed Fermentation with Trichoderma reesei.

    PubMed

    Wang, Shu-Yang; Jiang, Bo-Ling; Zhou, Xiang; Chen, Ji-Hong; Li, Wen-Jian; Liu, Jing; Hu, Wei; Xiao, Guo-Qing; Dong, Miao-Yin; Wang, Yu-Chen

    2015-01-01

    The aim of this study was to evaluate and validate the efficiency of 12C6+ irradiation of Aspergillus niger (A. niger) or mutagenesis via mixed Trichoderma viride (T. viride) culturing as well as a liquid cultivation method for cellulase production via mixed Trichoderma reesei (T. reesei) and A. niger culture fermentation. The first mutagenesis approach was employed to optimize yield from a cellulase-producing strain via heavy-ion mutagenesis and high-throughput screening, and the second was to effectively achieve enzymatic hydrolysis of cellulase from a mixed culture of mutant T. viride and A. niger. We found that 12C6+-ion irradiation induced changes in cellulase biosynthesis in A. niger but had no effect on the time course of the synthesis. It is notable that the exoglucanases (CBH) activities of A. niger strains H11-1 and H differed (6.71 U/mL vs. 6.01 U/mL) and were significantly higher than that of A. niger mutant H3-1. Compared with strain H, the filter paper assay (FPA), endoglucanase (EG) and β-glucosidase (BGL) activities of mutant strain H11-1 were increased by 250.26%, 30.26% and 34.91%, respectively. A mixed culture system was successfully optimized, and the best ratio of T. reesei to A. niger was 5:1 for 96 h with simultaneous inoculation. The BGL activity of the mixed culture increased after 72 h. At 96 h, the FPA and BGL activities of the mixed culture were 689.00 and 797.15 U/mL, respectively, significantly higher than those of monocultures, which were 408.70 and 646.98 U/mL for T. reesei and 447.29 and 658.89 U/mL for A. niger, respectively. The EG activity of the mixed culture was 2342.81 U/mL, a value that was significantly higher than that of monocultures at 2206.57 U/mL for T. reesei and 1727.62 U/mL for A. niger. In summary, cellulose production and hydrolysis yields were significantly enhanced by the proposed combination scheme.

  8. Study of a High-Yield Cellulase System Created by Heavy-Ion Irradiation-Induced Mutagenesis of Aspergillus niger and Mixed Fermentation with Trichoderma reesei

    PubMed Central

    Chen, Ji-Hong; Li, Wen-Jian; Liu, Jing; Hu, Wei; Xiao, Guo-Qing; Dong, Miao-Yin; Wang, Yu-Chen

    2015-01-01

    The aim of this study was to evaluate and validate the efficiency of 12C6+ irradiation of Aspergillus niger (A. niger) or mutagenesis via mixed Trichoderma viride (T. viride) culturing as well as a liquid cultivation method for cellulase production via mixed Trichoderma reesei (T. reesei) and A. niger culture fermentation. The first mutagenesis approach was employed to optimize yield from a cellulase-producing strain via heavy-ion mutagenesis and high-throughput screening, and the second was to effectively achieve enzymatic hydrolysis of cellulase from a mixed culture of mutant T. viride and A. niger. We found that 12C6+-ion irradiation induced changes in cellulase biosynthesis in A. niger but had no effect on the time course of the synthesis. It is notable that the exoglucanases (CBH) activities of A. niger strains H11-1 and H differed (6.71 U/mL vs. 6.01 U/mL) and were significantly higher than that of A. niger mutant H3-1. Compared with strain H, the filter paper assay (FPA), endoglucanase (EG) and β-glucosidase (BGL) activities of mutant strain H11-1 were increased by 250.26%, 30.26% and 34.91%, respectively. A mixed culture system was successfully optimized, and the best ratio of T. reesei to A. niger was 5:1 for 96 h with simultaneous inoculation. The BGL activity of the mixed culture increased after 72 h. At 96 h, the FPA and BGL activities of the mixed culture were 689.00 and 797.15 U/mL, respectively, significantly higher than those of monocultures, which were 408.70 and 646.98 U/mL for T. reesei and 447.29 and 658.89 U/mL for A. niger, respectively. The EG activity of the mixed culture was 2342.81 U/mL, a value that was significantly higher than that of monocultures at 2206.57 U/mL for T. reesei and 1727.62 U/mL for A. niger. In summary, cellulose production and hydrolysis yields were significantly enhanced by the proposed combination scheme. PMID:26656155

  9. Ion irradiation of astrophysical ices

    NASA Astrophysics Data System (ADS)

    Palumbo, M. E.; Baratta, G. A.; Fulvio, D.; Garozzo, M.; Gomis, O.; Leto, G.; Spinella, F.; Strazzulla, G.

    2008-02-01

    Ices, silicates and carbonaceous materials have been detected in several astrophysical environments such as interstellar molecular clouds, comets, and planetary surfaces. These solids are continuously exposed to ion irradiation and UV photolysis. Our knowledge on the properties of solids and molecules and on the modification induced by fast ions (keV-MeV) and UV photons is mainly based on laboratory experiments and on the comparison of experimental results with observations. Here we will give a few examples of the role of laboratory experiments to our understanding of the physical and chemical properties of ices in space.

  10. Emulation of reactor irradiation damage using ion beams

    DOE PAGES

    Was, G. S.; Jiao, Z.; Getto, E.; ...

    2014-06-14

    The continued operation of existing light water nuclear reactors and the development of advanced nuclear reactor depend heavily on understanding how damage by radiation to levels degrades materials that serve as the structural components in reactor cores. The first high dose ion irradiation experiments on a ferritic-martensitic steel showing that ion irradiation closely emulates the full radiation damage microstructure created in-reactor are described. Ferritic-martensitic alloy HT9 (heat 84425) in the form of a hexagonal fuel bundle duct (ACO-3) accumulated 155 dpa at an average temperature of 443°C in the Fast Flux Test Facility (FFTF). Using invariance theory as a guide,more » irradiation of the same heat was conducted using self-ions (Fe++) at 5 MeV at a temperature of 460°C and to a dose of 188 displacements per atom. The void swelling was nearly identical between the two irradiation and the size and density of precipitates and loops following ion irradiation are within a factor of two of those for neutron irradiation. The level of agreement across all of the principal microstructure changes between ion and reactor irradiation establishes the capability of tailoring ion irradiation to emulate the reactor-irradiated microstructure.« less

  11. Emulation of reactor irradiation damage using ion beams

    SciTech Connect

    Was, G. S.; Jiao, Z.; Getto, E.; Sun, K.; Monterrosa, A. M.; Maloy, S. A.; Anderoglu, O.; Sencer, B. H.; Hackett, M.

    2014-06-14

    The continued operation of existing light water nuclear reactors and the development of advanced nuclear reactor depend heavily on understanding how damage by radiation to levels degrades materials that serve as the structural components in reactor cores. The first high dose ion irradiation experiments on a ferritic-martensitic steel showing that ion irradiation closely emulates the full radiation damage microstructure created in-reactor are described. Ferritic-martensitic alloy HT9 (heat 84425) in the form of a hexagonal fuel bundle duct (ACO-3) accumulated 155 dpa at an average temperature of 443°C in the Fast Flux Test Facility (FFTF). Using invariance theory as a guide, irradiation of the same heat was conducted using self-ions (Fe++) at 5 MeV at a temperature of 460°C and to a dose of 188 displacements per atom. The void swelling was nearly identical between the two irradiation and the size and density of precipitates and loops following ion irradiation are within a factor of two of those for neutron irradiation. The level of agreement across all of the principal microstructure changes between ion and reactor irradiation establishes the capability of tailoring ion irradiation to emulate the reactor-irradiated microstructure.

  12. Aqueous marker penetration into ion irradiated polyimide

    NASA Astrophysics Data System (ADS)

    Fink, D.; Müller, M.; Petrov, A.; Klett, R.; Palmetshofer, L.; Hnatowicz, V.; Vacik, J.; Cervena, J.; Chadderton, L. T.

    2002-05-01

    The penetration of aqueous 6Li + markers into low energy ion irradiated polyimide (PI) foils was examined by the neutron depth profiling technique in combination with a modified tomographic approach. The ion irradiation always leads to an enhancement in marker uptake. After irradiation at low fluence the marker profiles follow the nuclear damage distribution even in three dimensions. At elevated fluences saturation in the marker uptake is clearly seen. The polymer's penetrant uptake can be described well by regular diffusion, with nuclear damage centres acting as saturable traps. These observations are strikingly different from the marker penetration into high-energy heavy-ion irradiated PI.

  13. Damage nucleation in Si during ion irradiation

    SciTech Connect

    Holland, O.W.; Fathy, D.; Narayan, J.

    1984-01-01

    Damage nucleation in single crystals of silicon during ion irradiation is investigated. Experimental results and mechanisms for damage nucleation during both room and liquid nitrogen temperature irradiation with different mass ions are discussed. It is shown that the accumulation of damage during room temperature irradiation depends on the rate of implantation. These dose rate effects are found to decrease in magnitude as the mass of the ions is increased. The significance of dose rate effects and their mass dependence on nucleation mechanisms is discussed.

  14. Folding two dimensional crystals by swift heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Ochedowski, Oliver; Bukowska, Hanna; Freire Soler, Victor M.; Brökers, Lara; Ban-d'Etat, Brigitte; Lebius, Henning; Schleberger, Marika

    2014-12-01

    Ion irradiation of graphene, the showcase model of two dimensional crystals, has been successfully applied to induce various modifications in the graphene crystal. One of these modifications is the formation of origami like foldings in graphene which are created by swift heavy ion irradiation under glancing incidence angle. These foldings can be applied to locally alter the physical properties of graphene like mechanical strength or chemical reactivity. In this work we show that the formation of foldings in two dimensional crystals is not restricted to graphene but can be applied for other materials like MoS2 and hexagonal BN as well. Further we show that chemical vapour deposited graphene forms foldings after swift heavy ion irradiation while chemical vapour deposited MoS2 does not.

  15. Li + grafting of ion irradiated polyethylene

    NASA Astrophysics Data System (ADS)

    Švorčík, V.; Rybka, V.; Vacík, J.; Hnatowicz, V.; Öchsner, R.; Ryssel, H.

    1999-02-01

    Foils of oriented polyethylene (PE) were irradiated with 63 keV Ar + and 155 keV Xe + ions to different fluences at room temperature and then doped from water solution of LiCl. The as irradiated and irradiated plus doped samples were examined by IR, EPR and neutron depth profiling (NDP) technique. The sheet resistance was also measured by the standard two points method. After Li salt doping of ion modified layer of PE, a reaction between degraded macromolecules and Li occur and thus a new chemical structure C-Li + is formed. Owing to the presence of these cations on the polymer chain, the irradiated plus doped layer exhibits higher electric conductivity compared to as-irradiated ones.

  16. Ion irradiation effects on metallic nanocrystals

    SciTech Connect

    Kluth, P.; Johannessen, B.; Giulian, R.; Schnohr, C.S.; Foran, G.J.; Cookson, D.J.; Byrne, A.P.; Ridgway, M.C.

    2008-04-02

    We have investigated structural and morphological properties of metallic nanocrystals (NCs) exposed to ion irradiation. NCs were characterized by transmission electron microscopy in combination with advanced synchrotron-based analytical techniques, in particular X-ray absorption spectroscopy and small-angle X-ray scattering. A number of different effects were observed depending on the irradiation conditions. At energies where nuclear stopping is predominant, structural disorder/amorphization followed by inverse Ostwald ripening/dissolution due to ion beam mixing was observed for Au and Cu NCs embedded in SiO{sub 2}. The ion-irradiation-induced crystalline to amorphous transition in the NCs, which cannot be achieved in the corresponding bulk metals, was attributed to their initially higher structural energy as compared to bulk material and possibly preferential nucleation of the amorphous phase at the NC/SiO{sub 2} interface. At very high irradiation energies (swift heavy ion irradiation), where the energy loss is nearly entirely due to electronic stopping, a size-dependent shape transformation of the NCs from spheres to rod like shapes was apparent in Au NCs. Our preliminary results are in good agreement with considerations on melting of the NCs in the ion track as one mechanism involved in the shape transformation.

  17. Dislocation loop formation by swift heavy ion irradiation of metals

    NASA Astrophysics Data System (ADS)

    Khara, Galvin S.; Murphy, Samuel T.; Duffy, Dorothy M.

    2017-07-01

    A coupled two-temperature, molecular dynamics methodology is used to simulate the structural evolution of bcc metals (Fe and W) and fcc metals (Cu and Ni) following irradiation by swift heavy ions. Electronic temperature dependent electronic specific heat capacities and electron-phonon coupling strengths are used to capture the full effects of the variation in the electronic density of states. Tungsten is found to be significantly more resistant to damage than iron, due both to the higher melting temperature and the higher thermal conductivity. Very interesting defect structures, quite different from defects formed in cascades, are found to be created by swift heavy ion irradiation in the bcc metals. Isolated vacancies form a halo around elongated interstitial dislocation loops that are oriented along the ion path. Such configurations are formed by rapid recrystallization of the molten cylindrical region that is created by the energetic ion. Vacancies are created at the recrystallization front, resulting in excess atoms at the core which form interstitial dislocation loops on completion of crystallization. These unique defect structures could, potentially, be used to create metal films with superior mechanical properties and interesting nanostructures.

  18. Slow ion irradiation of sugar: astrobiological implications

    NASA Astrophysics Data System (ADS)

    Tuleta, M.; Gabla, L.; Wickramasinghe, N. C.

    2009-10-01

    As a result of irradiation by slow hydrogen and argon ions of saccharose, humic films having a fractal nature were produced. The use of hydrogen ions simulated roughly the interaction of low-energy solar wind protons with interplanetary dust grains which, in addition to organic and mineral dust, may include clumps of viable bacteria. The type of film generated by this experimental procedure could play a role in shielding the interior of micron-sized clumps from damaging ultraviolet and low-energy cosmic ray irradiation. We argue that such films may have played a role in processes that led to the initial origin of life, and following the emergence of life the same types of films (as, for instance, in biofilms surrounding cells) may have been modified by irradiation to offer protection to viable cells in the interior.

  19. Deformation behavior of ion-irradiated polyimide

    SciTech Connect

    Kucheyev, S.O.; Felter, T.E.; Anthamatten, M.; Bradby, J.E.

    2004-08-02

    We study nanoindentation hardness, Young's modulus, and tensile strength of polyimide (Kapton H) films bombarded with MeV light ions in the predominantly electronic stopping power regime. Results show that, for all the ion irradiation conditions studied, bombardment increases the hardness and Young's modulus and decreases the tensile strength. These changes depend close to linearly on ion fluence and superlinearly (with a power-law exponent factor of {approx}1.5) on electronic energy loss. Physical mechanisms of radiation-induced changes to mechanical properties of polyimide are discussed.

  20. Early and Late Responses to Ion Irradiation

    NASA Astrophysics Data System (ADS)

    Schulte, Reinhard; Ling, Ted

    Early and late responses to ion beam therapy (IBT) are the result of complex interactions between host, dose volume, and radiobiological factors. Our understanding of these early and late tissue responses has improved greatly with the accumulation of laboratory and clinical experience with proton and heavy ion irradiation. With photon therapy becoming increasingly conformal, many concepts developed for 3D conformal radiotherapy and intensity modulated radiation therapy with photons are also applicable to IBT. This chapter reviews basic concepts and experimental data of early and late tissue responses to protons and ions.

  1. Characterisation of dual ion beam irradiated yttria-stabilised zirconia by specific analytical techniques

    NASA Astrophysics Data System (ADS)

    Zhang, Yanwen; Wang, Xu; Liu, Shiyi; Tang, Meixiong; Zhao, Ziqiang

    2015-01-01

    The combined effect of dual ion beam irradiated yttria-stabilized zirconia was investigated through Rutherford backscattering spectrometry/channeling (RBS/C), high resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM) and transmission electron microscopy (TEM). Compared with other experimental results of single ion beam irradiation, a multistep damage accumulation model can also explain the irradiation effects of dual ion beam. Irradiation damage created by Ar + He ions are simply additive and no synergy effect has been observed. The variation trends of step height and displacement damage are similar. The synergic effects of displacement damage between heavy recoil atoms and α-particle in nuclear waste matrices will not cause more serious damage than the sum of two kinds of ions. The two experimental damage peaks are consistent with those calculated using stopping and range of ions in matter (SRIM). Phase stability and irradiation resistance is further confirmed by high resolution transmission electron microscopy (HRTEM).

  2. Irradiation of a tin oxide nanometric powder with swift heavy ions

    NASA Astrophysics Data System (ADS)

    Berthelot, A.; Gourbilleau, F.; Dufour, C.; Domengès, B.; Paumier, E.

    2000-05-01

    Tin oxide nanometric powders have been irradiated with swift heavy ions (Ar, Cd, Ta, Pb and U) and observed by high resolution electron microscopy (HREM). Except for Ar ions, cylindrical tracks are visible. The mean track radius is all the more important since the electronic stopping power Se is high. Furthermore, the high-Se ions (Ta, Pb and U) create cylindrical holes, while in the case of Cd irradiations, a crystal-like contrast remains in the core track. Cylindrical holes correspond to a local zone where the maximum temperature calculated using the thermal spike model exceeds the boiling point. For Cd ion irradiations, a sputtering process is investigated.

  3. Mutation induced with ion beam irradiation in rose

    NASA Astrophysics Data System (ADS)

    Yamaguchi, H.; Nagatomi, S.; Morishita, T.; Degi, K.; Tanaka, A.; Shikazono, N.; Hase, Y.

    2003-05-01

    The effects of mutation induction by ion beam irradiation on axillary buds in rose were investigated. Axillary buds were irradiated with carbon and helium ion beams, and the solid mutants emerged after irradiation by repeated cutting back. In helium ion irradiation, mutations were observed in plants derived from 9 buds among 56 irradiated buds in 'Orange Rosamini' and in plants derived from 10 buds among 61 irradiated buds in 'Red Minimo'. In carbon ion, mutations were observed in plants derived from 12 buds among 88 irradiated buds in 'Orange Rosamini'. Mutations were induced not only in higher doses but also in lower doses, with which physiological effect by irradiation was hardly observed. Irradiation with both ion beams induced mutants in the number of petals, in flower size, in flower shape and in flower color in each cultivar.

  4. Chromosomal instability induced by heavy ion irradiation

    NASA Technical Reports Server (NTRS)

    Limoli, C. L.; Ponnaiya, B.; Corcoran, J. J.; Giedzinski, E.; Morgan, W. F.

    2000-01-01

    PURPOSE: To establish the dose-response relationship for the induction of chromosomal instability in GM10115 cells exposed to high-energy iron ions (1 GeV/nucleon, mean LET 146 keV/microm) and gold ions (11 GeV/nucleon, mean LET 1450 keV/microm). Past work has established that sparsely ionizing X-rays can induce a long-lived destabilization of chromosomes in a dose-dependent manner at an incidence of approximately 3% per gray. The present investigation assesses the capacity of High-Z and High-energy (HZE) particles to elicit this same endpoint. MATERIALS AND METHODS: Clonal populations derived from single progenitor cells surviving heavy-ion irradiation were analyzed cytogenetically to identify those clones showing a persistent destablization of chromosomes. RESULTS: Dose-response data, with a particular emphasis at low dose (< 1.0 Gy), indicate a frequency of approximately 4% per gray for the induction of chromosomal instability in clones derived from single progenitor cells surviving exposure to iron ions. The induction of chromosomal instability by gold ions was, however, less responsive to applied dose, as the observed incidence of this phenotype varied from 0 to 10% over 1-8 Gy. Both iron and gold ions gave dose-dependent increases in the yield of chromosomal aberrations (both chromosome- and chromatid-type) measured at the first mitosis following irradiation, as well as shoulderless survival curves having D0=0.87 and 1.1 Gy respectively. CONCLUSIONS: Based on the present dose-response data, the relative biological effectiveness of iron ions is 1.3 for the induction of chromosomal instability, and this indicates that heavy ions are only slightly more efficient than X-rays at eliciting this delayed phenotype.

  5. Chromosomal instability induced by heavy ion irradiation

    NASA Technical Reports Server (NTRS)

    Limoli, C. L.; Ponnaiya, B.; Corcoran, J. J.; Giedzinski, E.; Morgan, W. F.

    2000-01-01

    PURPOSE: To establish the dose-response relationship for the induction of chromosomal instability in GM10115 cells exposed to high-energy iron ions (1 GeV/nucleon, mean LET 146 keV/microm) and gold ions (11 GeV/nucleon, mean LET 1450 keV/microm). Past work has established that sparsely ionizing X-rays can induce a long-lived destabilization of chromosomes in a dose-dependent manner at an incidence of approximately 3% per gray. The present investigation assesses the capacity of High-Z and High-energy (HZE) particles to elicit this same endpoint. MATERIALS AND METHODS: Clonal populations derived from single progenitor cells surviving heavy-ion irradiation were analyzed cytogenetically to identify those clones showing a persistent destablization of chromosomes. RESULTS: Dose-response data, with a particular emphasis at low dose (< 1.0 Gy), indicate a frequency of approximately 4% per gray for the induction of chromosomal instability in clones derived from single progenitor cells surviving exposure to iron ions. The induction of chromosomal instability by gold ions was, however, less responsive to applied dose, as the observed incidence of this phenotype varied from 0 to 10% over 1-8 Gy. Both iron and gold ions gave dose-dependent increases in the yield of chromosomal aberrations (both chromosome- and chromatid-type) measured at the first mitosis following irradiation, as well as shoulderless survival curves having D0=0.87 and 1.1 Gy respectively. CONCLUSIONS: Based on the present dose-response data, the relative biological effectiveness of iron ions is 1.3 for the induction of chromosomal instability, and this indicates that heavy ions are only slightly more efficient than X-rays at eliciting this delayed phenotype.

  6. Nanoscale Morphology Evolution Under Ion Irradiation

    SciTech Connect

    Aziz, Michael J.

    2014-11-10

    We showed that the half-century-old paradigm of morphological instability under irradiation due to the curvature-dependence of the sputter yield, can account neither for the phase diagram nor the amplification or decay rates that we measure in the simplest possible experimental system -- an elemental semiconductor with an amorphous surface under noble-gas ion irradiation; We showed that a model of pattern formation based on the impact-induced redistribution of atoms that do not get sputtered away explains our experimental observations; We developed a first-principles, parameter-free approach for predicting morphology evolution, starting with molecular dynamics simulations of single ion impacts, lasting picoseconds, and upscaling through a rigorous crater-function formalism to develop a partial differential equation that predicts morphology evolution on time scales more than twelve orders of magnitude longer than can be covered by the molecular dynamics; We performed the first quantitative comparison of the contributions to morphological instability from sputter removal and from impact-induced redistribution of atoms that are removed, and showed that the former is negligible compared to the latter; We established a new paradigm for impact-induced morphology evolution based on crater functions that incorporate both redistribution and sputter effects; and We developed a model of nanopore closure by irradiation-induced stress and irradiationenhanced fluidity, for the near-surface irradiation regime in which nuclear stopping predominates, and showed that it explains many aspects of pore closure kinetics that we measure experimentally.

  7. Phase transformations in ion-irradiated silicides

    NASA Technical Reports Server (NTRS)

    Hewett, C. A.; Lau, S. S.; Suni, I.; Hung, L. S.

    1985-01-01

    The present investigation has three objectives. The first is concerned with the phase transformation of CoSi2 under ion implantation and the subsequent crystallization characteristics during annealing, taking into account epitaxial and nonepitaxial recrystallization behavior. The second objective is related to a study of the general trend of implantation-induced damage and crystallization behavior for a number of commonly used silicides. The last objective involves a comparison of the recrystallization behavior of cosputtered refractory silicides with that of the ion-implanted silicides. It was found that epitaxial regrowth of ion-irradiated CoSi2 occurred for samples with an epitaxial seed left at the Si/CoSi2 interface. A structural investigation of CoSi2 involving transmission electron microscopy (TEM) showed that after high-dose implantation CoSi2 is amorphous.

  8. Local brain heavy ion irradiation induced Immunosuppression

    NASA Astrophysics Data System (ADS)

    Lei, Runhong; Deng, Yulin; Huiyang Zhu, Bitlife.; Zhao, Tuo; Wang, Hailong; Yu, Yingqi; Ma, Hong; Wang, Xiao; Zhuang, Fengyuan; Qing, Hong

    Purpose: To investigate the long term effect of acute local brain heavy ion irradiation on the peripheral immune system in rat model. Methodology: Only the brain of adult male Wistar rats were radiated by heavy ions at the dose of 15 Gy. One, two and three months after irradiation, thymus and spleen were analyzed by four ways. Tunel assay was performed to evaluate the percentage of apoptotic cells in thymus and spleen, level of Inflammatory cytokines (IL-2, IL-6, SSAO, and TNF-α) was detected by ELISA assay, the differentiation of thymus T lymphocyte subsets were measured by flow cytometry and the relative expression levels of genes related to thymus immune cell development were measured by using quantitative real-time PCR. Results: Thymus and spleen showed significant atrophy from one month to three months after irradiation. A high level of apoptosis in thymus and spleen were obtained and the latter was more vulnerable, also, high level of inflammatory cytokines were found. Genes (c-kit, Rag1, Rag2 and Sca1) related to thymus lymphocytes’ development were down-regulated. Conclusion: Local area radiation in the rat brain would cause the immunosuppression, especially, the losing of cell-mediated immune functions. In this model, radiation caused inflammation and then induced apoptosis of cells in the immune organs, which contributed to immunosuppression.

  9. Manipulation of the graphene surface potential by ion irradiation

    SciTech Connect

    Ochedowski, O.; Kleine Bussmann, B.; Schleberger, M.; Ban d'Etat, B.; Lebius, H.

    2013-04-15

    We show that the work function of exfoliated single layer graphene can be modified by irradiation with swift (E{sub kin}=92 MeV) heavy ions under glancing angles of incidence. Upon ion impact individual surface tracks are created in graphene on silicon carbide. Due to the very localized energy deposition characteristic for ions in this energy range, the surface area which is structurally altered is limited to Almost-Equal-To 0.01 {mu}m{sup 2} per track. Kelvin probe force microscopy reveals that those surface tracks consist of electronically modified material and that a few tracks suffice to shift the surface potential of the whole single layer flake by Almost-Equal-To 400 meV. Thus, the irradiation turns the initially n-doped graphene into p-doped graphene with a hole density of 8.5 Multiplication-Sign 10{sup 12} holes/cm{sup 2}. This doping effect persists even after heating the irradiated samples to 500 Degree-Sign C. Therefore, this charge transfer is not due to adsorbates but must instead be attributed to implanted atoms. The method presented here opens up a way to efficiently manipulate the charge carrier concentration of graphene.

  10. Materials Modification Under Ion Irradiation: JANNUS Project

    SciTech Connect

    Serruys, Y.; Trocellier, P.; Trouslard, Ph.

    2004-12-01

    JANNUS (Joint Accelerators for Nano-Science and Nuclear Simulation) is a project designed to study the modification of materials using multiple ion beams and in-situ TEM observation. It will be a unique facility in Europe for the study of irradiation effects, the simulation of material damage due to irradiation and in particular of combined effects. The project is also intended to bring together experimental and modelling teams for a mutual fertilisation of their activities. It will also contribute to the teaching of particle-matter interactions and their applications. JANNUS will be composed of three accelerators with a common experimental chamber and of two accelerators coupled to a 200 kV TEM.

  11. High temperature annealing of ion irradiated tungsten

    DOE PAGES

    Ferroni, Francesco; Yi, Xiaoou; Arakawa, Kazuto; ...

    2015-03-21

    In this study, transmission electron microscopy of high temperature annealing of pure tungsten irradiated by self-ions was conducted to elucidate microstructural and defect evolution in temperature ranges relevant to fusion reactor applications (500–1200°C). Bulk isochronal and isothermal annealing of ion irradiated pure tungsten (2 MeV W+ ions, 500°C, 1014 W+/cm2) with temperatures of 800, 950, 1100 and 1400°C, from 0.5 to 8 h, was followed by ex situ characterization of defect size, number density, Burgers vector and nature. Loops with diameters larger than 2–3 nm were considered for detailed analysis, among which all loops had View the MathML source andmore » were predominantly of interstitial nature. In situ annealing experiments from 300 up to 1200°C were also carried out, including dynamic temperature ramp-ups. These confirmed an acceleration of loop loss above 900°C. At different temperatures within this range, dislocations exhibited behaviour such as initial isolated loop hopping followed by large-scale rearrangements into loop chains, coalescence and finally line–loop interactions and widespread absorption by free-surfaces at increasing temperatures. An activation energy for the annealing of dislocation length was obtained, finding Ea=1.34±0.2 eV for the 700–1100°C range.« less

  12. High temperature annealing of ion irradiated tungsten

    SciTech Connect

    Ferroni, Francesco; Yi, Xiaoou; Fitzgerald, Steven P.; Edmondson, Philip D.; Roberts, Steve G.

    2015-03-21

    In this study, transmission electron microscopy of high temperature annealing of pure tungsten irradiated by self-ions was conducted to elucidate microstructural and defect evolution in temperature ranges relevant to fusion reactor applications (500–1200°C). Bulk isochronal and isothermal annealing of ion irradiated pure tungsten (2 MeV W+ ions, 500°C, 1014 W+/cm2) with temperatures of 800, 950, 1100 and 1400°C, from 0.5 to 8 h, was followed by ex situ characterization of defect size, number density, Burgers vector and nature. Loops with diameters larger than 2–3 nm were considered for detailed analysis, among which all loops had View the MathML source and were predominantly of interstitial nature. In situ annealing experiments from 300 up to 1200°C were also carried out, including dynamic temperature ramp-ups. These confirmed an acceleration of loop loss above 900°C. At different temperatures within this range, dislocations exhibited behaviour such as initial isolated loop hopping followed by large-scale rearrangements into loop chains, coalescence and finally line–loop interactions and widespread absorption by free-surfaces at increasing temperatures. An activation energy for the annealing of dislocation length was obtained, finding Ea=1.34±0.2 eV for the 700–1100°C range.

  13. Raman spectroscopy of ion irradiated diamond

    NASA Astrophysics Data System (ADS)

    Brunetto, R.; Baratta, G. A.; Strazzulla, G.

    2004-07-01

    Ion irradiation experiments of diamond samples at room temperature have been performed by using in situ Raman spectroscopy as diagnostic technique. Different ions are used with energies of 200 or 400 keV. The area of virgin diamond Raman band (at 1332 cm-1) decreases exponentially as the ion fluence increases. This is due to changes in the optical properties of the damaged samples in the visible spectral range. Results from different ions demonstrate that this effect is correlated with the number of displacements/cm2, i.e., with the energy lost by ions through elastic collisions with target nuclei. Amorphous carbon (sp2) is formed after a threshold of about 2×1022 vacancies/cm3, or about 16 eV/C-atom deposited by elastic collisions. The peak position and full width at half maximum of the D line and G line of the synthesized amorphous carbon are studied. In particular, the G-line peak position shifts from the initial 1545 cm-1 to about 1515 cm-1 at the higher doses. The results are also discussed in view of their relevance in astrophysical environments.

  14. Raman spectroscopy of ion-irradiated astrophysically relevant materials

    NASA Astrophysics Data System (ADS)

    Baratta, G. A.; Brunetto, R.; Leto, G.; Palumbo, M. E.; Spinella, F.; Strazzulla, G.

    Solid objects in space (interstellar grains, comets, interplanetary dust particles, etc.) are continuously exposed to energetic processes, such as cosmic ion irradiation, that influence their evolution. In this paper we present an experimental study, carried out by Raman spectroscopy, of the effects induced by ion irradiation on frozen ices and refractory materials. If the irradiated ice mixture contains a relevant amount of carbon atoms, the ice is converted into an organic residue (stable at room temperature), which at high irradiation dose evolves toward a hydrogenated amorphous carbon. Here we show that material similar to that produced in the laboratory by ion irradiation of frozen ice mixtures and refractory materials can be formed in space by cosmic ion irradiation. This finding has been recently confirmed by the Stardust mission, which revealed in some of the cometary particles collected in space and returned to earth carbonaceous materials that have been processed by cosmic ion irradiation.

  15. Ion Irradiation of Carbon Nanotubes: a STM Study

    NASA Astrophysics Data System (ADS)

    Osváth, Z.; Vértesy, G.; Horváth, Z. E.; Gyulai, J.; Biró, L. P.

    2009-03-01

    Multi-walled carbon nanotubes irradiated with Ar+ ions of low (5×1011 ions/cm2) and high (1015 ions/cm2) fluences were investigated by STM. Contrary to the case of low fluence irradiation, the defects produced during the high fluence irradiation could not be observed individually, and the surface of nanotubes became rough. Irradiated nanotubes could be easily bent by the STM tip. However, some nanotubes parts could not be moved, which suggest that these parts were bound to the substrate during irradiation.

  16. Hydrogen retention in ion irradiated steels

    SciTech Connect

    Hunn, J.D.; Lewis, M.B.; Lee, E.H.

    1998-11-01

    In the future 1--5 MW Spallation Neutron Source, target radiation damage will be accompanied by high levels of hydrogen and helium transmutation products. The authors have recently carried out investigations using simultaneous Fe/He,H multiple-ion implantations into 316 LN stainless steel between 50 and 350 C to simulate the type of radiation damage expected in spallation neutron sources. Hydrogen and helium were injected at appropriate energy and rate, while displacement damage was introduced by nuclear stopping of 3.5 MeV Fe{sup +}, 1 {micro}m below the surface. Nanoindentation measurements showed a cumulative increase in hardness as a result of hydrogen and helium injection over and above the hardness increase due to the displacement damage alone. TEM investigation indicated the presence of small bubbles of the injected gases in the irradiated area. In the current experiment, the retention of hydrogen in irradiated steel was studied in order to better understand its contribution to the observed hardening. To achieve this, the deuterium isotope ({sup 2}H) was injected in place of natural hydrogen ({sup 1}H) during the implantation. Trapped deuterium was then profiled, at room temperature, using the high cross-section nuclear resonance reaction with {sup 3}He. Results showed a surprisingly high concentration of deuterium to be retained in the irradiated steel at low temperature, especially in the presence of helium. There is indication that hydrogen retention at spallation neutron source relevant target temperatures may reach as high as 10%.

  17. Trails of kilovolt ions created by subsurface channeling.

    PubMed

    Redinger, Alex; Standop, Sebastian; Michely, Thomas; Rosandi, Yudi; Urbassek, Herbert M

    2010-02-19

    Using scanning tunneling microscopy, we observe the damage trails produced by keV noble-gas ions incident at glancing angles onto Pt(111). Surface vacancies and adatoms aligned along the ion trajectory constitute the ion trails. Atomistic simulations reveal that these straight trails are produced by nuclear (elastic) collisions with surface layer atoms during subsurface channeling of the projectiles. In a small energy window around 5 keV, Xe+ ions create vacancy grooves that mark the ion trajectory with atomic precision. The asymmetry of the adatom production on the two sides of the projectile path is traced back to the asymmetry of the ion's subsurface channel.

  18. Trails of Kilovolt Ions Created by Subsurface Channeling

    SciTech Connect

    Redinger, Alex; Standop, Sebastian; Michely, Thomas; Rosandi, Yudi; Urbassek, Herbert M.

    2010-02-19

    Using scanning tunneling microscopy, we observe the damage trails produced by keV noble-gas ions incident at glancing angles onto Pt(111). Surface vacancies and adatoms aligned along the ion trajectory constitute the ion trails. Atomistic simulations reveal that these straight trails are produced by nuclear (elastic) collisions with surface layer atoms during subsurface channeling of the projectiles. In a small energy window around 5 keV, Xe{sup +} ions create vacancy grooves that mark the ion trajectory with atomic precision. The asymmetry of the adatom production on the two sides of the projectile path is traced back to the asymmetry of the ion's subsurface channel.

  19. Irradiation of Materials using Short, Intense Ion Beams

    NASA Astrophysics Data System (ADS)

    Seidl, Peter; Ji, Q.; Persaud, A.; Feinberg, E.; Silverman, M.; Sulyman, A.; Waldron, W. L.; Schenkel, T.; Barnard, J. J.; Friedman, A.; Grote, D. P.; Gilson, E. P.; Kaganovich, I. D.; Stepanov, A.; Zimmer, M.

    2016-10-01

    We present experiments studying material properties created with nanosecond and millimeter-scale ion beam pulses on the Neutralized Drift Compression Experiment-II at Berkeley Lab. The explored scientific topics include the dynamics of ion induced damage in materials, materials synthesis far from equilibrium, warm dense matter and intense beam-plasma physics. We describe the improved accelerator performance, diagnostics and results of beam-induced irradiation of thin samples of, e.g., tin and silicon. Bunches with >3x1010 ions/pulse with 1-mm radius and 2-30 ns FWHM duration and have been created. To achieve the short pulse durations and mm-scale focal spot radii, the 1.2 MeV He+ ion beam is neutralized in a drift compression section which removes the space charge defocusing effect during the final compression and focusing. Quantitative comparison of detailed particle-in-cell simulations with the experiment play an important role in optimizing the accelerator performance and keep pace with the accelerator repetition rate of <1/minute. This work was supported by the Office of Science of the US Department of Energy under contracts DE-AC0205CH11231 (LBNL), DE-AC52-07NA27344 (LLNL) and DE-AC02-09CH11466 (PPPL).

  20. Influence of ion irradiation on iron-chalcogenide superconducting films

    NASA Astrophysics Data System (ADS)

    Ozaki, Toshinori; Si, Weidong; Zhang, Cheng; Wu, Lijun; Li, Qiang

    2015-03-01

    Iron-chalcogenide superconductors have rather simple crystal structure and no charge reservoir. They also exhibit remarkable properties including small anisotoropy, high upper critical fields, a significant pressure effect on superconductivity. We have grown iron-chalcogenide FeSe0.5Te0.5 (FST) superconducting films on various substrate by pulsed laser deposition. The FST films on CeO2 buffer layer exhibit enhanced Tc (Tconset >20 K, Tczero = 18.0 K), which is about 30% higher than that found in the bulk materials and superior high field performance over the low temperature superconductors.. Recently, we were successful in further enhancement of Jc without Tc degradation by ion irradiation, especially, at high temperature and high magnetic field. The low-energy proton irradiation produces a Jc enhancement of one order of magnitude over the field of 6T//c at 12 K. Extensive TEM studies of the irradiated FST films have been carried out, which revealed an intriguing defect morphology provided by the irradiation. We will discuss the relationship between the superconducting properties and the created defects of the iron-chalcogenide films.

  1. Surface Modification of Polymer Substrates by Oxygen Ion Irradiation

    SciTech Connect

    Takaoka, G. H.; Ryuto, H.; Araki, R.; Yakushiji, T.

    2008-11-03

    Oxygen cluster ions and/or monomer ions were used for the sputtering and the surface modification of polymers such as polycarbonate (PC) and polyethylene terephthalate (PET). For the case of oxygen cluster ion irradiation, the sputtered depth increased with increase of the acceleration voltage, and the sputtering yield was much larger than that by the monomer ion irradiation. The sputtered particles represented the polymer structure, which indicated that the bond scission by the cluster ion irradiation resulted in an ejection of monomer molecule through the intermolecular collision. On the other hand, for the oxygen monomer ion irradiation, the implanted depth increased with increase of the acceleration voltage, and the bond scission occurred at the deep region through the binary collision with the high energetic ions. Therefore, the sputtering yield for the polymer surfaces decreased, and the sputtering effect became very small. Furthermore, the simultaneous use of oxygen cluster and monomer ions was more effective for oxidation of the PET surfaces rather than the monomer ion irradiation or the cluster ion irradiation. As a result, the contact angle measurement showed that the wettability of the PET surfaces irradiated by the simultaneous use of oxygen cluster and monomer ions was much enhanced.

  2. Surface Modification of Polymer Substrates by Oxygen Ion Irradiation

    NASA Astrophysics Data System (ADS)

    Takaoka, G. H.; Ryuto, H.; Araki, R.; Yakushiji, T.

    2008-11-01

    Oxygen cluster ions and/or monomer ions were used for the sputtering and the surface modification of polymers such as polycarbonate (PC) and polyethylene terephthalate (PET). For the case of oxygen cluster ion irradiation, the sputtered depth increased with increase of the acceleration voltage, and the sputtering yield was much larger than that by the monomer ion irradiation. The sputtered particles represented the polymer structure, which indicated that the bond scission by the cluster ion irradiation resulted in an ejection of monomer molecule through the intermolecular collision. On the other hand, for the oxygen monomer ion irradiation, the implanted depth increased with increase of the acceleration voltage, and the bond scission occurred at the deep region through the binary collision with the high energetic ions. Therefore, the sputtering yield for the polymer surfaces decreased, and the sputtering effect became very small. Furthermore, the simultaneous use of oxygen cluster and monomer ions was more effective for oxidation of the PET surfaces rather than the monomer ion irradiation or the cluster ion irradiation. As a result, the contact angle measurement showed that the wettability of the PET surfaces irradiated by the simultaneous use of oxygen cluster and monomer ions was much enhanced.

  3. Anderson localization of graphene by helium ion irradiation

    SciTech Connect

    Naitou, Y.; Ogawa, S.

    2016-04-25

    Irradiation of a single-layer graphene (SLG) with accelerated helium ions (He{sup +}) controllably generates defect distributions, which create a charge carrier scattering source within the SLG. We report direct experimental observation of metal-insulator transition in SLG on SiO{sub 2}/Si substrates induced by Anderson localization. This transition was investigated using scanning capacitance microscopy by monitoring the He{sup +} dose conditions on the SLG. The experimental data show that a defect density of more than ∼1.2% induced Anderson localization. We also investigated the localization length by determining patterned placement of the defects and estimated the length to be several dozen nanometers. These findings provide valuable insight for patterning and designing graphene-based nanostructures using helium ion microscopy.

  4. Spectral properties of ion irradiated carbon rich solids

    NASA Astrophysics Data System (ADS)

    Strazzulla, G.; Baratta, G.; Brunetto, R.; Garozzo, M.; Kanuchova, Z.

    2009-04-01

    Carbon rich solid materials have been studied before, during, and after ion irradiation (3-400 keV ions) by in situ reflectance spectroscopy (from UV to IR). Frozen hydrocarbons (benzene, methane, butane, acetylene, etc., also mixed with water ice) have been irradiated at low temperature with fast ions. Irradiation causes the formation of many molecular species and of a long chain polymer like material (organic refractory residue). The process mimics what occurs in space because of cosmic ion irradiation of the icy surfaces of some objects in the Solar System. Other irradiated materials include natural bitumens (Asphaltite, kerite) and polymers (i.e. polystyrene). Upon irradiation the originally transparent polymer samples are converted in a material that, already at low doses, strongly absorbs in the UV. Such materials could mimic a kind of organic material (i.e. a spectrally neutral one) freshly exposed at the surface of minor objects in the Solar System because of meteoritic impact.

  5. Efficient modification of floral traits by heavy-ion beam irradiation on transgenic Torenia.

    PubMed

    Ohtsubo, Norihiro; Sasaki, Katsutomo; Aida, Ryutaro; Ryuto, Hiromichi; Ichida, Hiroyuki; Hayashi, Yoriko; Abe, Tomoko

    2012-01-01

    While heavy-ion beam irradiation is becoming popular technology for mutation breeding in Japan, the combination with genetic manipulation makes it more convenient to create greater variation in plant phenotypes. We have succeeded in producing over 200 varieties of transgenic torenia (Torenia fournieri Lind.) from over 2,400 regenerated plants by this procedure in only 2 years. Mutant phenotypes were observed mainly in flowers and showed wide variation in colour and shape. Higher mutation rates in the transgenics compared to those in wild type indicate the synergistic effect of genetic manipulation and heavy-ion beam irradiation, which might be advantageous to create greater variation in floral traits.

  6. Enhancement of electric double layer capacitance of carbon nanotubes by gallium ion irradiation

    SciTech Connect

    Rai, Padmnabh; Pandey, Srikrishna; Menemparabath, Minimol; Sug Kim, Young; Nikolaev, Pavel; Arepalli, Sivaram; Lee, Il Ha

    2011-02-15

    Irradiation by 30 keV Ga{sup +} ions was used to create defects in multiwalled carbon nanotubes. Damage to the graphitic structure of the nanotube wall resulting from ion irradiation was observed by a transmission electron microscope which was accompanied by corresponding changes in Raman spectra. It was found that ion irradiation at 2 x 10{sup 13} ions/cm{sup 2} cumulative dose increases the electric double layer capacitance of a multiwalled carbon nanotube electrode by a factor of 2.3, followed by a decrease and saturation at higher (2 x 10{sup 14} and 4 x 10{sup 14} ions/cm{sup 2}) doses. This might be a trade-off between the enhancement caused by the tip opening and lowering of the capacitance due to amorphization of carbon nanotubes.

  7. Carbon nanowires generated by ion irradiation of hydrocarbon ices

    NASA Astrophysics Data System (ADS)

    Puglisi, O.; Compagnini, G.; D'Urso, L.; Baratta, G. A.; Palumbo, M. E.; Strazzulla, G.

    2014-05-01

    In this paper we present the formation of carbon nanowires (polyynes and polycumulenes) in the solid state by ion irradiation of frozen hydrocarbons (C6H6 and C2H2). Irradiations have been performed using H+ ions in the 100's keV energy regime using fluences up to 5 × 1014 ions/cm2. Beyond the intrinsic significance of these results in the field of material science, this work has been motivated by the fact that ion beam irradiation of hydrocarbon ices is one of the most important process thought to happen in several extraterrestrial environments where many spectroscopic features of polyyne molecules have been identified.

  8. Concurrent in situ ion irradiation transmission electron microscope

    DOE PAGES

    Hattar, K.; Bufford, D. C.; Buller, D. L.

    2014-08-29

    An in situ ion irradiation transmission electron microscope has been developed and is operational at Sandia National Laboratories. This facility permits high spatial resolution, real time observation of electron transparent samples under ion irradiation, implantation, mechanical loading, corrosive environments, and combinations thereof. This includes the simultaneous implantation of low-energy gas ions (0.8–30 keV) during high-energy heavy ion irradiation (0.8–48 MeV). In addition, initial results in polycrystalline gold foils are provided to demonstrate the range of capabilities.

  9. Concurrent in situ ion irradiation transmission electron microscope

    DOE PAGES

    Hattar, K.; Bufford, D. C.; Buller, D. L.

    2014-08-29

    An in situ ion irradiation transmission electron microscope has been developed and is operational at Sandia National Laboratories. This facility permits high spatial resolution, real time observation of electron transparent samples under ion irradiation, implantation, mechanical loading, corrosive environments, and combinations thereof. This includes the simultaneous implantation of low-energy gas ions (0.8–30 keV) during high-energy heavy ion irradiation (0.8–48 MeV). In addition, initial results in polycrystalline gold foils are provided to demonstrate the range of capabilities.

  10. Ion irradiation of CH 4-containing icy mixtures

    NASA Astrophysics Data System (ADS)

    Baratta, G. A.; Domingo, M.; Ferini, G.; Leto, G.; Palumbo, M. E.; Satorre, M. A.; Strazzulla, G.

    2003-08-01

    We have studied by infrared absorption spectroscopy the effects of ion irradiation with 60 keV Ar 2+ ions on pure methane (CH 4) ice at 12 K and mixtures with water (H 2O) and nitrogen (N 2). Ion irradiation, among other effects, causes the rupture of original molecular bonds and the formation of molecular species not present in the initial ice. Here we present the experimental results and discuss their astrophysical relevance.

  11. Application of ion beam irradiated ePTFE to repair small vessel injuries

    NASA Astrophysics Data System (ADS)

    Takahashi, N.; Suzuki, Y.; Ujiie, H.; Hori, T.; Iwaki, M.; Yamada, T.

    2007-04-01

    In surgery, bleeding from small injured vessels often requires prompt hemostasis without occlusion. This study evaluated the usefulness of 0.06 mm thick ion beam irradiated ePTFE sheets to repair small holes in vessels. Both surfaces of ePTFE sheets were irradiated with a 150 keV-Ar+ beam with fluences of 5 × 1014 ions/cm2. A small hole up to 2 mm in diameter was created in the common carotid artery of a rabbit. The defect was wrapped with an ion beam irradiated or non-irradiated ePTFE sheet. Fibrin glue was used to fix the ePTFE sheets to the common carotid artery. Hemostasis was instantly obtained with ion beam irradiated ePTFE but was rather difficult when using a non-irradiated ePTFE sheet. Three weeks after implantation, no occlusion was observed. Histological examination showed that the ePTFE sheets functioned as a scaffold for vessel wall regeneration. Thin ion beam irradiated ePTFE would be useful in vascular surgery.

  12. Mechanical property measurements on ion-irradiated metals

    SciTech Connect

    Zinkle, S.J.; Oliver, W.C.

    1986-08-01

    A recently developed mechanical properties microprobe (MPM) has been used to investigate strength and elastic modulus changes in ion-irradiated metals. The indenter load and its displacement are simultaneously monitored while the indentation is being made and also during unloading. Microindentation hardness measurements have been performed on ion-irradiated copper and Cu-0.15% Zr (AMZIRC). The depth dependence of the ion damage has been investigated in selected specimens which were prepared using a cross-section technique. This procedure allows a direct comparison to be made of hardness data from different irradiation depths while the indent size is held constant. The displacement damage associated with ion irradiation caused either hardening or softening, depending on the irradiation conditions and the material.

  13. Anti-biofilm activity of Fe heavy ion irradiated polycarbonate

    NASA Astrophysics Data System (ADS)

    Joshi, R. P.; Hareesh, K.; Bankar, A.; Sanjeev, Ganesh; Asokan, K.; Kanjilal, D.; Dahiwale, S. S.; Bhoraskar, V. N.; Dhole, S. D.

    2016-10-01

    Polycarbonate (PC) polymers were investigated before and after high energy heavy ion irradiation for anti-bacterial properties. These PC films were irradiated by Fe heavy ions with two energies, viz, 60 and 120 MeV, at different fluences in the range from 1 × 1011 ions/cm2 to 1 × 1013 ions/cm2. UV-Visible spectroscopic results showed optical band gap decreased with increase in ion fluences due to chain scission mainly at carbonyl group of PC which is also corroborated by Fourier transform infrared spectroscopic results. X-ray diffractogram results showed decrease in crystallinity of PC after irradiation which leads to decrease in molecular weight. This is confirmed by rheological studies and also by differential scanning calorimetric results. The irradiated PC samples showed modification in their surfaces prevents biofilm formation of human pathogen, Salmonella typhi.

  14. Ionoluminescence of fused silica under swift ion irradiation

    NASA Astrophysics Data System (ADS)

    Saavedra, R.; Jiménez-Rey, D.; Martin, P.; Vila, R.

    2016-09-01

    Ion beam induced luminescence spectra have been in-situ recorded during He+ (2.5 MeV), O4+ (13.5 MeV) and Si4+ (24.4 MeV) irradiations for three vitreous silica grades with different OH content (KU1, KS-4V and Infrasil 301). Remarkable changes in the ionoluminescence spectra of the three silica grades were observed for low ion fluences. He+ irradiated samples exhibited higher luminescence than equivalent ones irradiated with heavier O4+ and Si4+ ions. KU1 samples with the highest OH content showed the lowest blue luminescence. Blue luminescence maximum during ion irradiations with O4+ and Si4+ ions is correlated with structural changes.

  15. Swift Heavy Ion Irradiation Effects on NPN rf Power Transistors

    NASA Astrophysics Data System (ADS)

    Pushpa, N.; Prakash, A. P. Gnana; Gupta, S. K.; Revannasiddaiah, D.

    2011-07-01

    The dc characteristics of NPN rf power transistors were studied systematically before and after irradiation by 50 MeV Li3+ ions, 100 MeV F8+ ions and 140 MeV Si10+ ions in the dose range of 100 krad to 100 Mrad. The transistor parameters such as excess base current (ΔIB = IBpost-IBpre), dc current gain (hFE), and collector-saturation current (ICSat) were determined before and after irradiation. The base current (IB) was found to increase significantly after ion irradiation and this in turn decreases the hFE of the transistors. Further, the output characteristics of the irradiated devices exhibit the decrease in the collector current at the saturation region (ICSat) with increase of ion dose.

  16. Magnetic strip patterns induced by focused ion beam irradiation

    SciTech Connect

    Makarov, D.; Tibus, S.; Rettner, C. T.; Thomson, T.; Terris, B. D.; Schrefl, T.; Albrecht, M.

    2008-03-15

    Focused ion beam exposure was used to locally alter the magnetic properties of a continuous Co/Pd multilayer film with perpendicular magnetic anisotropy. The saturation magnetization, coercivity, and magnetic anisotropy of the films can be tuned by Ga irradiation depending on exposure dose. As a result, a periodic strip pattern consisting of 80 nm wide exposed strips which are magnetically soft, separated by 170 nm wide magnetically hard, unexposed areas was created. Due to strong magnetostatic coupling between the strips, a number of magnetic domain configurations could be stabilized and these have been observed by magnetic force microscopy and magneto-optic Kerr effect measurements. The magnetic domain configurations and their reversal behavior were investigated by micromagnetic simulations as a function of exposure dose and strip period.

  17. Effect of irradiation temperature on microstructural changes in self-ion irradiated austenitic stainless steel

    NASA Astrophysics Data System (ADS)

    Jin, Hyung-Ha; Ko, Eunsol; Lim, Sangyeob; Kwon, Junhyun; Shin, Chansun

    2017-09-01

    We investigated the microstructural and hardness changes in austenitic stainless steel after Fe ion irradiation at 400, 300, and 200 °C using transmission electron microscopy (TEM) and nanoindentation. The size of the Frank loops increased and the density decreased with increasing irradiation temperature. Radiation-induced segregation (RIS) was detected across high-angle grain boundaries, and the degree of RIS increases with increasing irradiation temperature. Ni-Si clusters were observed using high-resolution TEM in the sample irradiated at 400 °C. The results of this work are compared with the literature data of self-ion and proton irradiation at comparable temperatures and damage levels on stainless steels with a similar material composition with this study. Despite the differences in dose rate, alloy composition and incident ion energy, the irradiation temperature dependence of RIS and the size and density of radiation defects followed the same trends, and were very comparable in magnitude.

  18. Hopping magnetoresistance in ion irradiated monolayer graphene

    NASA Astrophysics Data System (ADS)

    Shlimak, I.; Zion, E.; Butenko, A. V.; Wolfson, L.; Richter, V.; Kaganovskii, Yu.; Sharoni, A.; Haran, A.; Naveh, D.; Kogan, E.; Kaveh, M.

    2016-02-01

    Magnetoresistance (MR) of ion irradiated monolayer graphene samples with a variable-range hopping (VRH) mechanism of conductivity was measured at temperatures down to T=1.8 K in magnetic fields up to B=8 T. It was observed that in perpendicular magnetic fields, hopping resistivity R decreases, which corresponds to negative MR (NMR), while parallel magnetic field results in positive MR (PMR) at low temperatures. NMR is explained on the basis of the "orbital" model in which perpendicular magnetic field suppresses the destructive interference of many paths through the intermediate sites in the total probability of the long-distance tunneling in the VRH regime. At low fields, a quadratic dependence (| ΔR / R | ∼ B2) of NMR is observed, while at B > B*, the quadratic dependence is replaced by the linear one. It was found that all NMR curves for different samples and different temperatures could be merged into common dependence when plotted as a function of B/B*. It is shown that B* ∼ T1/2 in agreement with predictions of the "orbital" model. The obtained values of B* also allowed us to estimate the localization radius ξ of charge carriers for samples with a different degree of disorder. PMR in parallel magnetic fields is explained by suppression of hopping transitions via double occupied states due to alignment of electron spins.

  19. Enhancement of band gap and photoconductivity in gamma indium selenide due to swift heavy ion irradiation

    SciTech Connect

    Sreekumar, R.; Jayakrishnan, R.; Sudha Kartha, C.; Vijayakumar, K. P.; Khan, S. A.; Avasthi, D. K.

    2008-01-15

    {gamma}-In{sub 2}Se{sub 3} thin films prepared at different annealing temperatures ranging from 100 to 400 deg. C were irradiated using 90 MeV Si ions with a fluence of 2x10{sup 13} ions/cm{sup 2}. X-ray diffraction analysis proved that there is no considerable variation in structural properties of the films due to the swift heavy ion irradiation. However, photosensitivity and sheet resistance of the samples increased due to irradiation. It was observed that the sample, which had negative photoconductivity, exhibited positive photoconductivity, after irradiation. The negative photoconductivity was due to the combined effect of trapping of photoexcited electrons, at traps 1.42 and 1.26 eV, above the valence band along with destruction of the minority carriers, created during illumination, through recombination. Photoluminescence study revealed that the emission was due to the transition to a recombination center, which was 180 meV above the valence band. Optical absorption study proved that the defects present at 1.42 and 1.26 eV were annealed out by the ion beam irradiation. This allowed photoexcited carriers to reach conduction band, which resulted in positive photoconductivity. Optical absorption study also revealed that the band gap of the material could be increased by ion beam irradiation. The sample prepared at 400 deg. C had a band gap of 2 eV and this increased to 2.8 eV, after irradiation. The increase in optical band gap was attributed to the annihilation of localized defect bands, near the conduction and valence band edges, on irradiation. Thus, by ion beam irradiation, one could enhance photosensitivity as well as the optical band gap of {gamma}-In{sub 2}Se{sub 3}, making the material suitable for applications such as window layer in solar cells.

  20. Ion irradiation of Fe-Fe oxide core-shell nanocluster films: Effect of interface on stability of magnetic properties

    NASA Astrophysics Data System (ADS)

    McCloy, John S.; Jiang, Weilin; Droubay, Timothy C.; Varga, Tamas; Kovarik, Libor; Sundararajan, Jennifer A.; Kaur, Maninder; Qiang, You; Burks, Edward C.; Liu, Kai

    2013-08-01

    A cluster deposition method was used to produce films of loosely aggregated nanoclusters (NCs) of Fe core-Fe3O4 shell or fully oxidized Fe3O4. Films of these NC on Si(100) or MgO(100)/Fe3O4(100) were irradiated to 1016 Si2+/cm2 near room temperature using an ion accelerator. Ion irradiation creates structural change in the NC film with corresponding chemical and magnetic changes which depend on the initial oxidation state of the cluster. Films were characterized using magnetometry (hysteresis, first order reversal curves), microscopy (transmission electron, helium ion), and x-ray diffraction. In all cases, the particle sizes increased due to ion irradiation, and when a core of Fe is present, irradiation reduces the oxide shells to lower valent Fe species. These results show that ion irradiated behavior of the NC films depends strongly on the initial nanostructure and chemistry, but in general saturation magnetization decreases slightly.

  1. He ion irradiation effects on multiwalled carbon nanotubes structure

    NASA Astrophysics Data System (ADS)

    Elsehly, Emad M.; Chechenin, Nikolay G.; Makunin, Alexey V.; Shemukhin, Andrey A.; Motaweh, Hussien A.

    2017-03-01

    Samples of multi-walled carbon nanotubes (MWNTs) were irradiated with 80 keV He ions. Scanning electron microscopy (SEM) inspection showed that the average outer diameters of the tube decreased as a result of ion irradiation. The samples were also characterized using Raman spectrometry by analysis of the intensity of main bands in the spectra of virgin and irradiated MWNT samples. Modifications of the disorder mode (D-band) and the tangential mode (G-band) were studied as a function of irradiation fluences. Raman spectra showed that as the fluence increases, the MWNTs first show disorder due to the produced defects, and then amorphization under still higher fluence of ion irradiation. Thermal and athermal mechanisms of the radiation induced MWNTs modifications are discussed. Contribution to the Topical Issue "Many Particle Spectroscopy of Atoms, Molecules, Clusters and Surfaces", edited by A.N. Grum-Grzhimailo, E.V. Gryzlova, Yu V. Popov, and A.V. Solov'yov.

  2. Failure Analysis of Heavy-Ion-Irradiated Schottky Diodes

    NASA Technical Reports Server (NTRS)

    Casey, Megan C.; Lauenstein, Jean-Marie; Wilcox, Edward P.; Topper, Alyson D.; Campola, Michael J.; Label, Kenneth A.

    2017-01-01

    In this work, we use high- and low-magnitude optical microscope images, infrared camera images, and scanning electron microscope images to identify and describe the failure locations in heavy-ion-irradiated Schottky diodes.

  3. Structure Change of PTFE by Low Energy Ion Irradiation

    NASA Astrophysics Data System (ADS)

    Watari, Kunio; Iwao, Toru; Yumoto, Motoshige

    The authors irradiate low energy nitrogen ion (100eV) on PTFE (poly-tetra-fluoro-ethylene) for surface modification. However, PTFE cannot anticipate adhesive strength improvement because it is collapse type polymer and weariness of surface occurs by ion irradiation. We paid attention to cross-linked structure to solve this problem. By this study introduce below, PTFE was changed collapse type polymer into cross-linked type polymer by rising temperature above the glass transition in the case of ion irradiation. As a result, the formation of the CF3 combination was restrained and collapse phenomenon was prevented by ion irradiation above the glass transition. In addition, it was suggested that cross-linked structure is effective for adhesive strength improvement by convolution of C1s spectrum and density profile.

  4. Enhanced electrochemical etching of ion irradiated silicon by localized amorphization

    SciTech Connect

    Dang, Z. Y.; Breese, M. B. H.; Lin, Y.; Tok, E. S.; Vittone, E.

    2014-05-12

    A tailored distribution of ion induced defects in p-type silicon allows subsequent electrochemical anodization to be modified in various ways. Here we describe how a low level of lattice amorphization induced by ion irradiation influences anodization. First, it superposes a chemical etching effect, which is observable at high fluences as a reduced height of a micromachined component. Second, at lower fluences, it greatly enhances electrochemical anodization by allowing a hole diffusion current to flow to the exposed surface. We present an anodization model, which explains all observed effects produced by light ions such as helium and heavy ions such as cesium over a wide range of fluences and irradiation geometries.

  5. Local magnetic field detector made by microscale ion irradiation on high temperature superconducting films

    NASA Astrophysics Data System (ADS)

    Laviano, Francesco; Gerbaldo, Roberto; Ghigo, Gianluca; Gozzelino, Laura; Minetti, Bruno; Mezzetti, Enrica

    2006-08-01

    Microscale modulations of the crystal structure in a continuous superconductor turn out to be effective for the spatial focusing of the energy dissipation induced by unpinned vortices. High-energy heavy-ion irradiation allowed the authors to finely control the defect density in order to study the properties of interfaces between pristine and irradiated parts of high temperature superconductors. In particular, strip-shaped samples were locally irradiated to create microscale modulations across their whole width. Magneto-optical imaging under electrical transport and magnetoresistive measurements imply that such tailored modulation in a superconducting strip can be exploited to develop a fully planar, single-compound, local magnetoresistive sensor.

  6. Ion irradiation of porous silicon : the role of surface states

    SciTech Connect

    Jacobsohn, L. G.; Bennett, B. L.; Cooke, D. W.; Muenchausen, Ross E.; Nastasi, Michael Anthony,

    2004-01-01

    The summary and conclusions of this paper are: (1) Ion irradiation induces PL quenching from po-Si; (2) Interaction of the implanted ions with defects generated during the irradiation process plays a major role in the PL quenching mechanism; (3) Quenching was associated with the creation of nonradiative states within the gap; and (4) Exposition to air and consequently the oxidation of the surface is shown to enhance PL emission efficiency.

  7. Ion irradiation testing of Improved Accident Tolerant Cladding Materials

    SciTech Connect

    Anderoglu, Osman; Tesmer, Joseph R.; Maloy, Stuart A.

    2014-01-14

    This report summarizes the results of ion irradiations conducted on two FeCrAl alloys (named as ORNL A&B) for improving the accident tolerance of LWR nuclear fuel cladding. After irradiation with 1.5 MeV protons to ~0.5 to ~1 dpa and 300°C nanoindentations were performed on the cross-sections along the ion range. An increase in hardness was observed in both alloys. Microstructural analysis shows radiation induced defects.

  8. Heavy-ion irradiation induced diamond formation in carbonaceous materials.

    SciTech Connect

    Daulton, T. L.

    1999-01-08

    The basic mechanisms of metastable phase formation produced under highly non-equilibrium thermodynamic conditions within high-energy particle tracks are investigated. In particular, the possible formation of diamond by heavy-ion irradiation of graphite at ambient temperature is examined. This work was motivated, in part, by earlier studies which discovered nanometer-grain polycrystalline diamond aggregates of submicron-size in uranium-rich carbonaceous mineral assemblages of Precambrian age. It was proposed that the radioactive decay of uranium formed diamond in the fission particle tracks produced in the carbonaceous minerals. To test the hypothesis that nanodiamonds can form by ion irradiation, fine-grain polycrystalline graphite sheets were irradiated with 400 MeV Kr ions. The ion irradiated graphite (and unirradiated graphite control) were then subjected to acid dissolution treatments to remove the graphite and isolate any diamonds that were produced. The acid residues were then characterized by analytical and high-resolution transmission electron microscopy. The acid residues of the ion-irradiated graphite were found to contain ppm concentrations of nanodiamonds, suggesting that ion irradiation of bulk graphite at ambient temperature can produce diamond.

  9. Surface reformation and electro-optical characteristics of liquid crystal alignment layers using ion beam irradiation

    SciTech Connect

    Oh, Byeong-Yun; Lee, Kang-Min; Kim, Byoung-Yong; Kim, Young-Hwan; Han, Jin-Woo; Han, Jeong-Min; Lee, Sang-Keuk; Seo, Dae-Shik

    2008-09-15

    The surface modification characteristics of liquid crystal (LC) alignment layers irradiated with various argon (Ar) ion beam (IB) energies were investigated as a substitute for rubbing technology. Various pretilt angles were created on the IB-irradiated polyimide (PI) surfaces after IB irradiation, but the Ar ions did not alter the morphology on the PI surface, indicating that the pretilt angle was not due to microgrooves. The chemical bonding states of the IB-irradiated PI surfaces were analyzed in detail by x-ray photoelectron spectroscopy to verify the compositional behavior for the LC alignment. Chemical structure analysis showed that the alignment ability of LCs was due to the preferential reorientation of the carbon network due to the breaking of C=O double bonds in the imide ring parallel to the incident IB direction. The potential of applying nonrubbing technology to display devices was further supported by the superior electro-optical characteristics compared to rubbed PI.

  10. Buried amorphous layers by electronic excitation in ion-beam irradiated lithium niobate: Structure and kinetics

    SciTech Connect

    Olivares, J.; Garcia-Navarro, A.; Garcia, G.; Agullo-Lopez, F.; Agullo-Rueda, F.; Garcia-Cabanes, A.; Carrascosa, M.

    2007-02-01

    The formation of buried heavily damaged and amorphous layers by a variety of swift-ion irradiations (F at 22 MeV, O at 20 MeV, and Mg at 28 MeV) on congruent LiNbO{sub 3} has been investigated. These irradiations assure that the electronic stopping power S{sub e}(z) is dominant over the nuclear stopping S{sub n}(z) and reaches a maximum value inside the crystal. The structural profile of the irradiated layers has been characterized in detail by a variety of spectroscopic techniques including dark-mode propagation, micro-Raman scattering, second-harmonic generation, and Rutherford backscattering spectroscopy/channeling. The growth of the damage on increasing irradiation fluence presents two differentiated stages with an abrupt structural transition between them. The heavily damaged layer reached as a final stage is optically isotropic (refractive index n=2.10, independent of bombarding ion) and has an amorphous structure. Moreover, it has sharp profiles and its thickness progressively increases with irradiation fluence. The dynamics under irradiation of the amorphous-crystalline boundaries has been associated with a reduction of the effective amorphization threshold due to the defects created by prior irradiation (cumulative damage). The kinetics of the two boundaries of the buried layer is quite different, suggesting that other mechanisms aside from the electronic stopping power should play a role on ion-beam damage.

  11. Edge-on ion irradiation of electron microscope specimens

    SciTech Connect

    Otero, M.P. |; Allen, C.W.

    1992-07-01

    A special technique is described for in situ transmission electron microscope (TEM) experiments involving simultaneous ion irradiation, in which the resultant phenomena are observed as in a cross-section TEM specimen. That is, instead of ion-irradiating the film or foil specimen normal to the major surfaces and observing in plan view (i.e., in the same direction), the specimen is irradiated edge-on (i.e., parallel to the major surfaces) and is observed normal to the depth direction with respect to the irradiation. The results of amorphization of Si, irradiated in this orientation by 1 or 1.5 MeV Kr, are presented and briefly compared with the usual plan view observations. The limitations of the technique are discussed and several experiments which might profitably employ this technique are suggested.

  12. Edge-on ion irradiation of electron microscope specimens

    SciTech Connect

    Otero, M.P. Fundacao de Tecnologia Industrial , Lorena, SP ); Allen, C.W. )

    1992-01-01

    A special technique is described for in situ transmission electron microscope (TEM) experiments involving simultaneous ion irradiation, in which the resultant phenomena are observed as in a cross-section TEM specimen. That is, instead of ion-irradiating the film or foil specimen normal to the major surfaces and observing in plan view (i.e., in the same direction), the specimen is irradiated edge-on (i.e., parallel to the major surfaces) and is observed normal to the depth direction with respect to the irradiation. The results of amorphization of Si, irradiated in this orientation by 1 or 1.5 MeV Kr, are presented and briefly compared with the usual plan view observations. The limitations of the technique are discussed and several experiments which might profitably employ this technique are suggested.

  13. The conductivity of high-fluence noble gas ion irradiated CVD polycrystalline diamond

    NASA Astrophysics Data System (ADS)

    Borisov, A. M.; Kazakov, V. A.; Mashkova, E. S.; Ovchinnikov, M. A.; Shemukhin, A. A.; Sigalaev, S. K.

    2017-09-01

    The conductivity of surface layer of polycrystalline CVD (Chemical Vapor Deposition) diamond has been studied experimentally after high-fluence 30 keV Ne+, 20 and 30 keV Ar+ ion irradiation at target temperature range from 30 to 400 °C. The hot ion irradiation of CVD diamond may be described as ion-stimulated heat graphitization in which an exponential resistance decrease with increasing of the irradiation temperature is much faster than at the heat treatment. Under ion irradiation of CVD diamond the graphite-like materials resistivity is achieved at temperatures not exceeding 200 °C. The graphite phase in a heterogeneous structure of diamond irradiated layer is in dynamic equilibrium. In the temperature range from RT to 400 °C, the proportion of graphite phase increases so that at temperatures 200 < Tir < 400 °C it is dominant. The Raman spectra of ion-induced conductive layer created on CVD diamond reflect the processes of nanostructural ordering - disordering of sp2-bonded carbon.

  14. Morphological study of borosilicate glass surface irradiated by heavy ions

    SciTech Connect

    Wang, T. S.; Du, X.; Yuan, W.; Duan, B. H.; D. Zhang, J.; Chen, L.; Peng, H. B.; Yang, D.; Zhang, G. F.; Zhu, Z. H.

    2016-11-01

    Borosilicate glass is a candidate material for radiation waste formation and other optical applications in various fields. To understand the radiation effect of borosilicate glass, heavy ion (Arq+, Krq+ and Xeq+) irradiations were used to simulate the alpha and recoiled nuclei irradiations in this study. The surface morphology of glass has been compared to ion irradiation doses and ion energies. The surface topography evolution of irradiated samples is characterized by optical microscopy, atomic force microscopy (AFM), transmission electron microscopy (TEM) and secondary ion mass spectrometry (SIMS). Micro-bumps are observed on the sample surface after irradiationwith 5 MeV Xeq+ over 5 × 1013 ions·cm-2. The size and density of the bumps increaseswith increasing irradiation dose. At a lowdose, bumps are on the nanometer (nm) scale and rather rare.While the dose is higher than 9 × 1015 ions·cm-2, the size of bumps is on the scale of a few microns, and the density is saturated. However, the height of the bumps increases froma fewnmto over 150nmwith further irradiation. The distribution of micro-bumps is nearly homogeneous. The bumps are condensed and swell up, and there is no crystallized structure according to the TEMdiffraction pattern. Elementmigration and concentrations are observedwith SIMS imaging. The arrayed micro-bumps are a new finding, and they might be used to change the surface properties. Bump formation is caused by phase separation, and volume swelling is induced by ion irradiation.

  15. Anomalous Plastic Deformation and Sputtering of Ion Irradiated Silicon Nanowires

    PubMed Central

    2015-01-01

    Silicon nanowires of various diameters were irradiated with 100 keV and 300 keV Ar+ ions on a rotatable and heatable stage. Irradiation at elevated temperatures above 300 °C retains the geometry of the nanostructure and sputtering can be gauged accurately. The diameter dependence of the sputtering shows a maximum if the ion range matches the nanowire diameter, which is in good agreement with Monte Carlo simulations based on binary collisions. Nanowires irradiated at room temperature, however, amorphize and deform plastically. So far, plastic deformation has not been observed in bulk silicon at such low ion energies. The magnitude and direction of the deformation is independent of the ion-beam direction and cannot be explained with mass-transport in a binary collision cascade but only by collective movement of atoms in the collision cascade with the given boundary conditions of a high surface to volume ratio. PMID:25951108

  16. Anomalous Plastic Deformation and Sputtering of Ion Irradiated Silicon Nanowires.

    PubMed

    Johannes, Andreas; Noack, Stefan; Wesch, Werner; Glaser, Markus; Lugstein, Alois; Ronning, Carsten

    2015-06-10

    Silicon nanowires of various diameters were irradiated with 100 keV and 300 keV Ar(+) ions on a rotatable and heatable stage. Irradiation at elevated temperatures above 300 °C retains the geometry of the nanostructure and sputtering can be gauged accurately. The diameter dependence of the sputtering shows a maximum if the ion range matches the nanowire diameter, which is in good agreement with Monte Carlo simulations based on binary collisions. Nanowires irradiated at room temperature, however, amorphize and deform plastically. So far, plastic deformation has not been observed in bulk silicon at such low ion energies. The magnitude and direction of the deformation is independent of the ion-beam direction and cannot be explained with mass-transport in a binary collision cascade but only by collective movement of atoms in the collision cascade with the given boundary conditions of a high surface to volume ratio.

  17. Simulation of radiation damage in minerals by sequential ion irradiations

    NASA Astrophysics Data System (ADS)

    Nakasuga, W. M.; Li, W.; Ewing, R. C.

    2015-12-01

    Radiation effects due to α-decay of U and Th and spontaneous fission of 238U control the production and recovery of the radiation-induced structure of minerals, as well as the diffusion of elements through the mineral host. However, details of how the damage microstructure is produced and annealed remain unknown. Our recent ion beam experiments demonstrate that ionizing radiation from the α-particle recovers the damage structure. Thus, the damage structure is not only the result of the thermal hisotry of the sample, but also of the complex interaction between ionizing and ballistic damage mechanisms. By combining ion irradiations with transmission electron microscopy (TEM), we have simulated the damage produced by α-decay and fission. The α-particle induced annealing has been simulated by in situ TEM observation of consecutive ion-irradiations: i.) 1 MeV Kr2+ (simulating 70 keV α-recoils induced damage), ii.) followed by 400 keV He+ (simulating 4.5 MeV α-particle induced annealing). Thus, in addition to the well-established effects of thermal annealing, the α-particle annealing effects, as evidenced by partical recrystallization of the originally, fully-amorphous apatite upon the α-particle irriadations, should also be considered when evaluating diffusion and release of elements, such as He. In addition, the fission track annealing has been simulated by a new sample preparation method that allows for direct observation of radiation damage recovery at each point along the length of latent tracks created by 80 MeV Xe ions (a typical fission fragment). The initial, rapid reduction in etched track length during isothermal annealing is explained by the rapid annealing of those sections of the track with smaller diameters, as observed directly by in situ TEM. In summary, the atomic-scale investigation of radiation damage in minerals is critical to understanding of the influence of raidation damage on diffusion and kinetics that are fundamental to geochronology.

  18. Characterization of swift heavy ion irradiation damage in ceria

    SciTech Connect

    Yablinsky, Clarissa; Devanathan, Ram; Pakarinen, Janne; Gan, Jian; Severin, Daniel; Trautmann, Christina; Allen, T. R.

    2015-05-14

    We have examined microstructural evolution in irradiated ceria (CeO2) using swift heavy ion irradiation, electron microscopy, and atomistic simulation. CeO2, a UO2 fuel surrogate, was irradiated with gold ions at an energy of 1 GeV to fluences up to 1x1014 ions/cm2. Transmission electron microscopy accompanied by electron energy loss spectroscopy showed that the ion tracks were of similar size at all fluences, and that there was no chemical change in the ion track core. Classical molecular dynamics simulations of thermal spikes in CeO2 with energy deposition of 12 and 36 keV/nm show damage consisting of isolated point defects at the lower energy and defect clusters at 36 keV/nm, with no amorphization at either energy. Inferences are drawn from modeling about density changes in the ion track and the formation of interstitial loops that shed light on features observed by electron microscopy of swift heavy ion irradiated ceria.

  19. Irradiation effects of displacement damage and gas atoms in Yttria-stabilized zirconia irradiated by Au and helium ions

    NASA Astrophysics Data System (ADS)

    Zhang, Yanwen; Zhao, Ziqiang; Guo, Gang

    2017-07-01

    Single and sequential ion beam irradiated Yttria-stabilized zirconia (YSZ) was carried out to study the irradiation effects of vacancies and helium gas atoms. The results show that the displacement damage value of sequential ion beam irradiation is less than that of single He ion irradiation and larger than that of single Au ion irradiation. The irradiation effects of displacement damage (mainly vacancies) and gas atoms may lead to a strong reduction of the interstitial helium atoms. Sequential ion beam irradiation generates more vacancies-helium bubbles than single helium ion irradiation. The results are important for fundamental understanding of interaction between vacancy and helium bubbles, and it also plays a guiding role in the practical industrial applications in the nuclear reactor.

  20. Creating and studying ion acoustic waves in ultracold neutral plasmas

    SciTech Connect

    Killian, T. C.; Castro, J.; McQuillen, P.; O'Neil, T. M.

    2012-05-15

    We excite ion acoustic waves in ultracold neutral plasmas by imprinting density modulations during plasma creation. Laser-induced fluorescence is used to observe the density and velocity perturbations created by the waves. The effect of expansion of the plasma on the evolution of the wave amplitude is described by treating the wave action as an adiabatic invariant. After accounting for this effect, we determine that the waves are weakly damped, but the damping is significantly faster than expected for Landau damping.

  1. Forsterite amorphisation by ion irradiation: Monitoring by infrared spectroscopy

    NASA Astrophysics Data System (ADS)

    Brucato, J. R.; Strazzulla, G.; Baratta, G.; Colangeli, L.

    2004-01-01

    We present experimental results on the crystal-amorphous transition of forsterite (Mg2SiO4) silicate under ion irradiation. The aim of this work is to study the structural evolution of one of the most abundant crystalline silicates observed in space driven by ion irradiation. To this aim, forsterite films have been synthesised in the laboratory and irradiated with low energy (30-60 keV) ion beams. Structural changes during irradiation with H+, He+, C+, and Ar++ have been observed and monitored by infrared spectroscopy. The fraction of crystalline forsterite converted into the amorphous form is a function of the energy deposited by nuclear collision by ions in the target. Laboratory results indicate that ion irradiation is a mechanism potentially active in space for the amorphisation of silicates. Physical properties obtained in this work can be used to model the evolution of silicate grains during their life cycle from evolved stars, through different interstellar environments and up to being incorporated in Solar System objects.

  2. Effect of heavy-ion and electron irradiation on properties of Fe-based superconductors

    NASA Astrophysics Data System (ADS)

    Konczykowski, Marcin

    2013-03-01

    The introduction of defects by particle irradiation is used to reveal the role of disorder in matter, which is unavoidable in all crystalline solids. In superconductors defects introduce flux pinning, controlling critical current, Jc; as well as pair-breaking scattering, limiting the critical temperature, Tc. To elucidate defect related properties of Fe-based superconductors (FBS) we precede in two types of irradiation: heavy ion (6GeV Pb) to create disorder in the form of amorphous tracks and low temperature electron irradiation (2.5MeV at 20K) to create point like defects. Substantial increase of irreversible magnetization and an upward shift of the irreversibility line are observed after heavy ion irradiation of all FBS investigated to date. In BaK 122 , signatures of a Bose-glass vortex state; angular dependence and variable-range hopping flux creep are revealed. Remarkably, heavy ion irradiation does not depress Tc, however, point-like disorder introduced by electron irradiation does substantially. In isovalently substituted Ba(FeAs1 - xPx) 2 and Ba(Fe1 - x Rux As) 2 crystals, Tc decreases linearly with dose. Suppression to 40 % of initial value of Tc was achieved in Ba(FeAs1 - xPx) 2 . An increase of normal state resistivity is observed and correlated to depression of Tc. Change of superconducting gap structure with disorder was determined from penetration depth measurements, λ (T) dependence, at various stages of irradiation. Linear in T variation of pristine samples, indicative of the presence of nodes in gap, turned at low irradiation dose to exponential T variation, indicative of a fully gaped state. T2 variation of λ is observed at higher doses. This behaviour is incompatible with symmetry-imposed nodes of d-wave pairing but consistent with S + / - , S + / + mechanisms. This is the first observation of the impurity-induced node lifting expected in anisotropic s-wave superconductors

  3. Raman measurements in silica glasses irradiated with energetic ions

    SciTech Connect

    Saavedra, R. Martin, P.; Vila, R.; León, M.; Jiménez-Rey, D.; Girard, S.; Boukenter, A.; Ouerdane, Y.

    2014-10-21

    Ion irradiation with energetic He{sup +} (2.5 MeV), O{sup 4+} (13.5 MeV), Si{sup 4+} (24.4 MeV) and Cu{sup 7+} (32.6 MeV) species at several fluences (from 5 × 10{sup 12} to 1.65 × 10{sup 15} ion/cm{sup 2}) were performed in three types of SiO{sub 2} glasses with different OH content (KU1, KS-4V and Infrasil 301). After ion implantation the Raman spectra were measured and compared with the spectra of unirradiated samples. Irradiated samples of the three fused silica grades exhibit changes in the broad and asymmetric R-band (ω{sub 1} around 445 cm{sup −1}), in D{sub 1} (490 cm−1) and D{sub 2} (605 cm{sup −1}) bands associated to small-membered rings. The D{sub 2} band shows an increase with increasing fluences for different ions, indicating structural changes. Raman spectra of ion-irradiated samples were compared with the spectra of neutron irradiated samples at fluences 10{sup 17} n/cm{sup 2} and 1018 n/cm{sup 2}. Macroscopic surface cracking was detected, mainly at fluences corresponding to deposited energies between 10{sup 23} eV/cm{sup 3} and 10{sup 24} eV/cm{sup 3} (after ion beam shutdown)

  4. Ion irradiation of ices: astrochemical and astrobiological applications.

    NASA Astrophysics Data System (ADS)

    Strazzulla, G.; Brucato, J. R.; Palumbo, M. E.; Spinella, F.

    We present some recent results obtained by an ongoing research that aims into the experimental study of the effects induced by fast ions in solids, in particular frozen gases. The technique used to analyze the effects of irradiation has been "in situ" infrared spectroscopy. Here we discuss the formation of carbon chain oxides (e.g. C_3O_2) after ion irradiation of frozen CO. A detailed study of the IR spectroscopic properties of solid frozen formamide is presented along with the modifications induced by ion irradiation. The results are relevant to explain the presence of molecules in the circumstellar environment of a newly born star. Those molecules could be produced by energetic processing of dust and released to the gas phase after warming up.

  5. Reduction and structural modification of zirconolite on He+ ion irradiation

    NASA Astrophysics Data System (ADS)

    Gupta, Merry; Kulriya, P. K.; Shukla, Rishabh; Dhaka, R. S.; Kumar, Raj; Ghumman, S. S.

    2016-07-01

    The immobilization of minor actinides and alkaline-earth metal is a major concern in nuclear industry due to their long-term radioactive contribution to the high level waste (HLW). Materials having zirconolite, pyrochlore, and perovskite structure are promising candidates for immobilization of HLW. The zirconolite which exhibits high radiation stability and corrosion resistance behavior is investigated for its radiation stability against alpha particles in the present study. CaZrTi2O7 pellets prepared using solid state reaction techniques, were irradiated with 30 keV He+ ions for the ion fluence varying from 1 × 1017 to 1 × 1021 ions/m2. Scanning electron microscopy (SEM) images of the un-irradiated sample exhibited well separated grains with average size of about 6.8 μm. On the ion irradiation, value of the average grains size was about 7.1 μm, and change in the microstructure was insignificant. The X-ray photoelectron spectroscopy (XPS) studies showed a shift in the core level peak position (of Ca 2p, Ti 2p and Zr 3d) towards lower binding energy with respect to pristine sample as well as loss of oxygen was also observed for sample irradiated with the ion fluence of 1 × 1020 ions/m2. These indicate a decrease in co-ordination number and the ionic character of Msbnd O bond. Moreover, core level XPS signal was not detected for sample irradiated with ion fluence of 1 × 1021 ions/m2, suggesting surface damage of the sample at this ion fluence. However, X-ray diffraction (XRD) studies showed that zirconolite was not amorphized even on irradiation up to a fluence order of 1 × 1021 ion/m2. But, significant decrease in peak intensity due to creation of defects and a marginal positive peak shift due to tensile strain induced by irradiation, were observed. Thus, XRD along with XPS investigation suggests that reduction, decrease in co-ordination number, and increase in covalency are responsible for the radiation damage in zirconolite.

  6. Surface modification of multilayer graphene using Ga ion irradiation

    SciTech Connect

    Wang, Quan; Shao, Ying; Ge, Daohan; Ren, Naifei; Yang, Qizhi

    2015-04-28

    The effect of Ga ion irradiation intensity on the surface of multilayer graphene was examined. Using Raman spectroscopy, we determined that the irradiation caused defects in the crystal structure of graphene. The density of defects increased with the increase in dwell times. Furthermore, the strain induced by the irradiation changed the crystallite size and the distance between defects. These defects had the effect of doping the multilayer graphene and increasing its work function. The increase in work function was determined using contact potential difference measurements. The surface morphology of the multilayer graphene changed following irradiation as determined by atomic force microscopy. Additionally, the adhesion between the atomic force microscopy tip and sample increased further indicating that the irradiation had caused surface modification, important for devices that incorporate graphene.

  7. Ion irradiation of TNO surface analogue ice mixtures: the chemistry .

    NASA Astrophysics Data System (ADS)

    Baratta, G. A.; Brunetto, R.; Caniglia, G.; Fulvio, D.; Ioppolo, S.; Leto, G.; Palumbo, M. E.; Spinella, F.; Strazzulla, G.

    Vis-NIR spectra of some Centaurs and Trans-Neptunian Objects (TNOs) indicate surfaces rich in H_2O, N_2, CO_2, CH_4 e CH_3OH. Cosmic ion irradiation is one of the processes driving the evolution of TNO surfaces. A main role is played by the chemistry induced by colliding ions; many molecular bonds are broken along the ion track, and this may lead to the formation of byproduct molecules. Starting from laboratory experiments, it is possible to infer the presence of molecules still undetected on TNOs. For instance, carbonic acid (H_2CO_3) is produced after irradiation of H_2O:CO_2 icy mixtures, while irradiation of H_2O:N_2 icy mixtures causes the production of N_2O, NO, and NO_2. From H_2O:CH_4:N_2 mixtures, many species are formed, such as CO, CO_2, HCN, HNCO, N_2O, and molecules including CN bonds. Moreover, ion irradiation may modify the relative intensity of NIR features, as in the case of solid methanol, whose 2.34 mu m band decreases in intensity with respect to the 2.27 mu m band, after increasing irradiation doses. We suggest that this effect may be observed on Centaur Pholus.

  8. Structural evolution of zirconium carbide under ion irradiation

    NASA Astrophysics Data System (ADS)

    Gosset, D.; Dollé, M.; Simeone, D.; Baldinozzi, G.; Thomé, L.

    2008-02-01

    Zirconium carbide is one of the candidate materials to be used for some fuel components of the high temperature nuclear reactors planned in the frame of the Gen-IV project. Few data exist regarding its behaviour under irradiation. We have irradiated ZrC samples at room temperature with slow heavy ions (4 MeV Au, fluence from 10 11 to 5 × 10 15 cm -2) in order to simulate neutron irradiations. Grazing incidence X-Ray diffraction (GIXRD) and transmission electron microscopy (TEM) analysis have been performed in order to study the microstructural evolution of the material versus ion fluence. A high sensitivity to oxidation is observed with the formation of zirconia precipitates during the ion irradiations. Three damage stages are observed. At low fluence (<10 12 cm -2), low modifications are observed. At intermediate fluence, high micro-strains appear together with small faulted dislocation loops. At the highest fluence (>10 14 cm -2), the micro-strains saturate and the loops coalesce to form a dense dislocation network. No other structural modification is observed. The material shows a moderate cell parameter increase, corresponding to a 0.6 vol.% swelling, which saturates around 10 14 ions/cm 2, i.e., a few Zr dpa. As a result, in spite of a strong covalent bonding component, ZrC seems to have a behaviour under irradiation close to cubic metals.

  9. Improvement in Adhesive Strength of PTFE using Nitrogen Ion Irradiation

    NASA Astrophysics Data System (ADS)

    Watanabe, Tsuyoshi; Iwao, Toru; Yumoto, Motoshige

    The adhesive strength doesn't improve so much even if the surface is activated. It is known that PTFE (polytetra fluoroethylene) is one of the collapse type polymer since the binding energy of main chain is smaller than that of side chain. Accordingly, it is assumed that adhesive strength may improve by suppressing the collapse of structure. It is also expected that introduction of cross-linking structure may suppress the collapse of structure. It was confirmed that a lot of polar radicals were introduced at the surface by nitrogen ion irradiation around 30 eV. Thus, to introduce the cross-linking structure several 100 eV nitrogen ions were irradiated after irradiation of nitrogen with 30 eV ion. As a result, adhesive strength irradiated by 300 eV improved more than that of 1000 eV. From the result of XPS (X-ray-Photoelectron-Spectroscopy) analysis, many C-N-C bonds contributing cross-linking structure was detected at a shallow layer by irradiation of ions with 300 eV. From these results, it is concluded that the depth of cross-link formation is important to improve the adhesive strength.

  10. Crystalline nanostructures on Ge surfaces induced by ion irradiation

    NASA Astrophysics Data System (ADS)

    Ou, Xin; Facsko, Stefan

    2014-12-01

    Besides conventional low efficiency lithographic techniques broad ion beam irradiation is a simple and potentially mass productive technique to fabricate nanoscale patterns on various semiconductor surfaces. The main drawback of this method is that the irradiated semiconductor surfaces are amorphized, which strongly limits the potential application of these nanostructures in electronic and optoelectronic devices. In this work we report that high-quality crystalline nanostructure patterns are formed on Ge surfaces via Ar+ irradiation at elevated temperatures. This pattern formation process resembles the pattern formation in homoepitaxy. Therefore, the process is discussed based on a 'reverse epitaxy' mechanism.

  11. Ion irradiation of ammonia/carbon dioxide mixtures

    NASA Astrophysics Data System (ADS)

    Lv, X. Y.; Boduch, P.; Ding, J. J.; Domaracka, A.; Langlinay, T.; Palumbo, M. E.; Rothard, H.; Strazzulla, G.

    2013-09-01

    We present new experimental results on the thermal and ion irradiation processing of ammonia/carbon dioxide frozen mixtures. Mixtures deposited at low T (16 K) have then been warmed up to 160 K. During warm up complex chemical reactions occur leading to the formation of new molecules and, in particular, of ammonium carbamate. Other samples have been irradiated with 144 keV S9+ ions. Also in this case new chemical species are formed among which CO and OCN-. The results are discussed in the light of their relevance to understand the effects of different processes going on in the variegated superficial and sub-superficial layers of Enceladus.

  12. FTIR study of silicon carbide amorphization by heavy ion irradiations

    NASA Astrophysics Data System (ADS)

    Costantini, Jean-Marc; Miro, Sandrine; Pluchery, Olivier

    2017-03-01

    We have measured at room temperature (RT) the Fourier-transform infra-red (FTIR) absorption spectra of ion-irradiated thin epitaxial films of cubic silicon carbide (3C-SiC) with 1.1 µm thickness on a 500 µm thick (1 0 0) silicon wafer substrate. Irradiations were carried out at RT with 2.3 MeV 28Si+ ions and 3.0 MeV 84Kr+ ions for various fluences in order to induce amorphization of the SiC film. Ion projected ranges were adjusted to be slightly larger than the film thickness so that the whole SiC layers were homogeneously damaged. FTIR spectra of virgin and irradiated samples were recorded for various incidence angles from normal incidence to Brewster’s angle. We show that the amorphization process in ion-irradiated 3C-SiC films can be monitored non-destructively by FTIR absorption spectroscopy without any major interference of the substrate. The compared evolutions of TO and LO peaks upon ion irradiation yield valuable information on the damage process. Complementary test experiments were also performed on virgin silicon nitride (Si3N4) self-standing films for similar conditions. Asymmetrical shapes were found for TO peaks of SiC, whereas Gaussian profiles are found for LO peaks. Skewed Gaussian profiles, with a standard deviation depending on wave number, were used to fit asymmetrical peaks for both materials. A new methodology for following the amorphization process is proposed on the basis of the evolution of fitted IR absorption peak parameters with ion fluence. Results are discussed with respect to Rutherford backscattering spectrometry channeling and Raman spectroscopy analysis.

  13. Sputtering of metals at ion-electron irradiation

    NASA Astrophysics Data System (ADS)

    Martynenko, Yu. V.; Korshunov, S. N.; Skorlupkin, I. D.

    2014-02-01

    It has been found that, in contrast to the commonly accepted opinion, simultaneous irradiation by 15-keV Ar+ ions and 2.5-keV electrons at temperatures above 0.5 T m ( T m is the melting temperature) induces much larger sputtering of metallic copper, nickel, and steel than irradiation only by Ar+ ions. The effect increases with the temperature. At T = 0.7 T m, the sputtering coefficients in the case of ion-electron irradiation are more than twice as large as the sputtering coefficients in the case of irradiation by Ar+ ions. The experiments on the sublimation of copper show that the sublimation rate in the case of the heating of a sample by an electron beam is higher than that in the case of heating in an electric vacuum oven. The revealed effects are explained by the electron-induced excitation of adatoms (atoms stuck over the surface, which appear owing to ion bombardment). Excited adatoms have a smaller binding energy with the surface and are sputtered more easily.

  14. Effect of ion beam irradiation and rubbing on the directional behavior and alignment mechanism of liquid crystals on polyimide surfaces

    SciTech Connect

    Lee, Kang-Min; Oh, Byeong-Yun; Kim, Young-Hwan; Seo, Dae-Shik

    2009-01-01

    We investigated the effects of ion beam (IB) irradiation and rubbing on the directional behavior and alignment mechanism of liquid crystals (LCs) on polyimide (PI) surfaces. We found that the LC direction follows the IB irradiation alignment direction on the PI surface regardless of whether the irradiation occurs before or after rubbing. We assumed that the LC direction depends strongly on the C-O bonds created from C=O bonds on the PI surface broken by IB irradiation and conducted an investigation of the chemical bonding state of the PI surface by x-ray photoelectron spectroscopy.

  15. Ion irradiation induced impurity redistribution in Pt/C multilayers

    NASA Astrophysics Data System (ADS)

    Bera, S.; Goswami, D. K.; Bhattacharjee, K.; Dev, B. N.; Kuri, G.; Nomoto, K.; Yamashita, K.

    2003-12-01

    Ion irradiation induced modifications of a periodic Pt/C multilayer system containing Fe impurity have been analyzed by X-ray techniques suitable for exploring nanometer depth scales with sub-nanometer depth resolution. The multilayer stack with 15 Pt/C layer pairs (period 4.23 nm, total thickness 63.45 nm) was fabricated on a glass substrate. A 2 MeV Au 2+ ion beam was rastered on the sample to obtain uniformly irradiated strips with fluences from 1 × 10 14 to 1 × 10 15 ions/cm 2. These strips were analyzed with X-ray standing wave and X-ray reflectivity experiments. Ion induced atomic displacements across multilayer interfaces are known [Appl. Phys. Lett. 79 (2001) 467]. Here additionally we identify irradiation induced redistribution of Fe impurity atoms, which cannot be explained simply by atomic displacements due to ion-atom collision. With increasing ion fluences more Fe atoms migrate from C- to Pt-layers. This behaviour has been explained in terms of radiation induced enhanced diffusion and Fe-Pt and Fe-C phase diagrams.

  16. Tailoring the properties of copper nanowires by ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Kumar, Narinder; Kumar, Rajesh; Kumar, Sushil; Chakarvarti, S. K.

    2016-02-01

    In the present paper, we investigated the change in the properties of copper nanowires under the irradiance of 80 MeV Si7+ ion beam. The nanowires were electrodeposited in the cylindrical pores of the track-etched polycarbonate membranes. The phase, morphology and optical absorbance of the fabricated nanowires were characterized by powder X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and UV-visible spectroscopy, respectively. The XRD study showed a face centered cubic crystal structure of copper nanowires. Further measurements with FESEM revealed that nanowires were continuous, aligned with uniform diameter having high aspect ratio. The XRD spectra of irradiated nanowires indicated an improved crystalinity at low ion fluences while it declines at higher ion fluences. The optical absorbance properties of the irradiated copper nanowires were also examined. The absorption spectra exhibited a peak at 568 nm which was attributed to the surface plasmon resonance. A significant increase in absorbance after irradiation accounts for the possibility of defects formation. The electrical properties measured from I-V characteristics showed an increase in resistivity of irradiated nanowires.

  17. Irradiation hardening of ODS ferritic steels under helium implantation and heavy-ion irradiation

    NASA Astrophysics Data System (ADS)

    Zhang, Hengqing; Zhang, Chonghong; Yang, Yitao; Meng, Yancheng; Jang, Jinsung; Kimura, Akihiko

    2014-12-01

    Irradiation hardening of ODS ferritic steels after multi-energy He-ion implantation, or after irradiation with energetic heavy ions including Xe and Bi-ions was investigated with nano-indentation technique. Three kinds of high-Cr ODS ferritic steels including the commercial MA956 (19Cr-3.5Al), the 16Cr-0.1Ti and the 16Cr-3.5Al-0.1Zr were used. Data of nano-hardness were analyzed with an approach based on Nix-Gao model. The depth profiles of nano-hardness can be understood by the indentation size effect (ISE) in specimens of MA956 implanted with multi-energy He-ions or irradiated with 328 MeV Xe ions, which produced a plateau damage profile in the near-surface region. However, the damage gradient overlaps the ISE in the specimens irradiated with 9.45 Bi ions. The dose dependence of the nano-hardness shows a rapid increase at low doses and a slowdown at higher doses. An 1/2-power law dependence on dpa level is obtained. The discrepancy in nano-hardness between the helium implantation and Xe-ion irradiation can be understood by using the average damage level instead of the peak dpa level. Helium-implantation to a high dose (7400 appm/0.5 dpa) causes an additional hardening, which is possibly attributed to the impediment of motion dislocations by helium bubbles formed in high concentration in specimens.

  18. Point defects induced in ion irradiated 4H-SiC probed by exciton lines

    NASA Astrophysics Data System (ADS)

    Litrico, G.; Zimbone, M.; Calcagno, L.; Musumeci, P.; Baratta, G. A.; Fotil, G.

    2009-05-01

    The defects produced in 4H-SiC epitaxial layers by irradiation with a 200 keV H+ ion beam in the fluence range 6.5 × 1011-1.8 × 1013 ions/cm2 are investigated by Low Temperature Photoluminescence (LTPL-40 K). The defects produced by ion beam irradiation induce the formation of some sharp lines called "alphabet lines" in the photoluminescence spectra in the 425-443 nm range, due to the recombination of excitons at structural defects. From the LTPL lines intensity trend, as function of proton fluence, it is possible to single out two groups of peaks: the P1 lines (e, f, g) and the P2 lines (a, b, c, d) that exhibit different trends with the ion fluence. The P1 group normalized yield increases with ion fluence, reaches a maximum at 2.5 × 1012 ions/cm2 and then decreases. The P2 group normalized yield, instead, exhibits a formation threshold at low fluence, then increases until a maximum value at a fluence of 3.5 × 1012 ions/cm2 and decreases at higher fluence, reaching a value of 50% of the maximum yield. The behaviour of P1 and P2 lines, with ion fluence, indicates a production of point defects at low fluence, followed by a subsequent local rearrangement creating complex defects at high fluence.

  19. Zirconium oxidation under high-energy heavy-ion irradiation

    SciTech Connect

    Bererd, N.; Chevarier, A.; Moncoffre, N.; Jaffrezic, H.; Balanzat, E.; Catalette, H.

    2005-04-15

    This paper concerns the study of zirconium oxidation under irradiation with high energetic Xe ions. The irradiations were performed on the IRRadiation SUD (IRRSUD) beam line at Grand Accelerateur National d'Ions Lourds of Caen. The oxygen partial pressure was fixed at 10{sup -3} Pa and two temperature conditions were used, either 480 deg. C reached by Joule effect heating or 280 deg. C due to Xe energy deposition. Zirconia was fully characterized by Rutherford backscattering spectrometry, scanning electron microscopy, and grazing angle x-ray diffraction. Apparent diffusion coefficients of oxygen in ZrO{sub 2} were determined from these experiments by using a model which takes into account a surface exchange between oxygen gas and the ZrO{sub 2} surface. These results are compared with thermal oxidation data.

  20. Amorphization and reduction of thermal conductivity in porous silicon by irradiation with swift heavy ions

    SciTech Connect

    Newby, Pascal J.; Canut, Bruno; Bluet, Jean-Marie; Lysenko, Vladimir; Gomes, Severine; Isaiev, Mykola; Burbelo, Roman; Chantrenne, Patrice; Frechette, Luc G.

    2013-07-07

    In this article, we demonstrate that the thermal conductivity of nanostructured porous silicon is reduced by amorphization and also that this amorphous phase in porous silicon can be created by swift (high-energy) heavy ion irradiation. Porous silicon samples with 41%-75% porosity are irradiated with 110 MeV uranium ions at six different fluences. Structural characterisation by micro-Raman spectroscopy and SEM imaging show that swift heavy ion irradiation causes the creation of an amorphous phase in porous Si but without suppressing its porous structure. We demonstrate that the amorphization of porous silicon is caused by electronic-regime interactions, which is the first time such an effect is obtained in crystalline silicon with single-ion species. Furthermore, the impact on the thermal conductivity of porous silicon is studied by micro-Raman spectroscopy and scanning thermal microscopy. The creation of an amorphous phase in porous silicon leads to a reduction of its thermal conductivity, up to a factor of 3 compared to the non-irradiated sample. Therefore, this technique could be used to enhance the thermal insulation properties of porous Si. Finally, we show that this treatment can be combined with pre-oxidation at 300 Degree-Sign C, which is known to lower the thermal conductivity of porous Si, in order to obtain an even greater reduction.

  1. Effects of Ga ion-beam irradiation on monolayer graphene

    SciTech Connect

    Wang, Quan; Mao, Wei; Zhang, Yanmin; Shao, Ying; Ren, Naifei; Ge, Daohan

    2013-08-12

    The effects of Ga ion on the single layer graphene (SLG) have been studied by Raman spectroscopy (RS), SEM, and field-effect characterization. Under vacuum conditions, Ga ion-irradiation can induce disorders and cause red shift of 2D band of RS, rather than lattice damage in high quality SLG. The compressive strain induced by Ga ion decreases the crystalline size in SLG, which is responsible for the variation of Raman scattering and electrical properties. Nonlinear out-put characteristic and resistance increased are also found in the I-V measurement. The results have important implications during CVD graphene characterization and related device fabrication.

  2. Ion beam irradiated optical channel waveguides

    NASA Astrophysics Data System (ADS)

    Bányász, I.; Rajta, I.; Nagy, G. U. L.; Zolnai, Z.; Havranek, V.; Pelli, S.; Veres, M.; Himics, L.; Berneschi, S.; Nunzi-Conti, G.; Righini, G. C.

    2014-03-01

    Nowadays, in the modern optical communications systems, channel waveguides represent the core of many active and passive integrated devices, such as amplifiers, lasers, couplers and splitters. Different materials and fabrication processes were investigated in order to achieve the aforementioned optoelectronic circuits with low costs and high performance and reproducibility. Nevertheless, the 2D guiding structures fabrication continues to be a challenging task in some of optical materials due to their susceptibility to mechanical and/or chemical damages which can occur during the different steps of the fabrication process. Here we report on channel waveguides demonstration in erbium doped Tungsten - Tellurite (Er3+:TeO2-WO3) glasses and BGO crystals by means of a masked ion beam and/or direct writing processes performed at different energy MeV and ions species. The evidence of the waveguides formation was investigated by microscopy techniques and micro Raman spectroscopy.

  3. Comparison of Deuterium Retention for Ion-irradiated and Neutron-irradiated Tungsten

    SciTech Connect

    Yasuhisa Oya; Masashi Shimada; Makoto Kobayashi; Takuji Oda; Masanori Hara; Hideo Watanabe; Yuji Hatano; Pattrick Calderoni; Kenji Okuno

    2011-12-01

    The behavior of D retention for Fe{sup 2+}-irradiated tungsten with a damage of 0.025-3 dpa was compared with that for neutron-irradiated tungsten with 0.025 dpa. The D{sub 2} thermal desorption spectroscopy (TDS) spectra for Fe{sup 2+}-irradiated tungsten consisted of two desorption stages at 450 and 550 K, while that for neutron-irradiated tungsten was composed of three stages and an addition desorption stage was found at 750 K. The desorption rate of the major desorption stage at 550K increased as the displacement damage increased due to Fe{sup 2+} irradiation increasing. In addition, the first desorption stage at 450K was found only for damaged samples. Therefore, the second stage would be based on intrinsic defects or vacancy produced by Fe{sup 2+} irradiation, and the first stage should be the accumulation of D in mono-vacancy and the activation energy would be relatively reduced, where the dislocation loop and vacancy is produced. The third one was found only for neutron irradiation, showing the D trapping by a void or vacancy cluster, and the diffusion effect is also contributed to by the high full-width at half-maximum of the TDS spectrum. Therefore, it can be said that the D{sub 2} TDS spectra for Fe{sup 2+}-irradiated tungsten cannot represent that for the neutron-irradiated one, indicating that the deuterium trapping and desorption mechanism for neutron-irradiated tungsten is different from that for the ion-irradiated one.

  4. Development of a compact single ion irradiation system

    NASA Astrophysics Data System (ADS)

    Iida, T.; Tanaka, T.; Sato, F.; Tanimura, Y.

    2000-12-01

    A compact single ion irradiation system has been developed to examine energetic particle effects on materials and devices. The system has been constructed by use of commercially available and inexpensive standard components and can be easily recomposed according to beam requirements for various irradiation experiments. The beam adjustment was automatically performed by help of a computer program based on a modified SIMPLEX method. The beam performances of the system, i.e., pulse width, the number of ions included in one pulse and beam size were examined by use of a microchannel plate, a Si-SSD, a CCD image sensor and a CR-39 track detector, respectively. A beam of a single ion, 1 nsec in pulse width and several /spl mu/m in diameter has been successfully produced by this system.

  5. Effects on focused ion beam irradiation on MOS transistors

    SciTech Connect

    Campbell, A.N.; Peterson, K.A.; Fleetwood, D.M.; Soden, J.M.

    1997-04-01

    The effects of irradiation from a focused ion beam (FIB) system on MOS transistors are reported systematically for the first time. Three MOS transistor technologies, with 0.5, 1, and 3 {mu}m minimum feature sizes and with gate oxide thicknesses ranging from 11 to 50 nm, were analyzed. Significant shifts in transistor parameters (such as threshold voltage, transconductance, and mobility) were observed following irradiation with a 30 keV Ga{sup +} focused ion beam with ion doses varying by over 5 orders of magnitude. The apparent damage mechanism (which involved the creation of interface traps, oxide trapped charge, or both) and extent of damage were different for each of the three technologies investigated.

  6. Temporal stability of Y Ba Cu O nano Josephson junctions from ion irradiation

    SciTech Connect

    Cybart, Shane A.; Roediger, Peter; Chen, Ke; Parker, J. M.; Cho, Ethan Y.; Wong, Travis J.; Dynes, R. C.

    2012-11-29

    We investigate the temporal stability of YBa2Cu3O7 Josephson junctions created by ion irradiation through a nano-scale implant mask fabricated using electron beam lithography and reactive ion etching. A comparison of current-voltage characteristics measured for junctions after fabrication and eight years of storage at room temperature show a slight decrease in critical current and increase in normal state resistance consistent with broadening of the weaklink from diffusion of defects. Shapiro step measurements performed 8 years after fabrication reveal that device uniformity is maintained and is strong evidence that these devices have excellent temporal stability for applications.

  7. Investigation of high-energy ion-irradiated MA957 using synchrotron radiation under in-situ tension

    SciTech Connect

    Mo, Kun; Yun, Di; Miao, Yinbin; Liu, Xiang; Pellin, Michael; Almer, Jonathan; Park, Jun -Sang; Stubbins, James F.; Zhu, Shaofei; Yacout, Abdellatif M.

    2016-01-02

    In this paper, an MA957 oxide dispersion-strengthened (ODS) alloy was irradiated with high-energy ions in the Argonne Tandem Linac Accelerator System. Fe ions at an energy of 84 MeV bombarded MA957 tensile specimens, creating a damage region similar to 7.5 μm in depth; the peak damage (similar to 40 dpa) was estimated to be at similar to 7 μm from the surface. Following the irradiation, in-situ high-energy X-ray diffraction measurements were performed at the Advanced Photon Source in order to study the dynamic deformation behavior of the specimens after ion irradiation damage. In-situ X-ray measurements taken during tensile testing of the ion-irradiated MA957 revealed a difference in loading behavior between the irradiated and un-irradiated regions of the specimen. At equivalent applied stresses, lower lattice strains were found in the radiation-damaged region than those in the un-irradiated region. This might be associated with a higher level of Type II stresses as a result of radiation hardening. The study has demonstrated the feasibility of combining high-energy ion radiation and high-energy synchrotron X-ray diffraction to study materials' radiation damage in a dynamic manner.

  8. Investigation of High-Energy Ion-Irradiated MA957 Using Synchrotron Radiation under In-Situ Tension.

    PubMed

    Mo, Kun; Yun, Di; Miao, Yinbin; Liu, Xiang; Pellin, Michael; Almer, Jonathan; Park, Jun-Sang; Stubbins, James F; Zhu, Shaofei; Yacout, Abdellatif M

    2016-01-02

    In this study, an MA957 oxide dispersion-strengthened (ODS) alloy was irradiated with high-energy ions in the Argonne Tandem Linac Accelerator System. Fe ions at an energy of 84 MeV bombarded MA957 tensile specimens, creating a damage region ~7.5 μm in depth; the peak damage (~40 dpa) was estimated to be at ~7 μm from the surface. Following the irradiation, in-situ high-energy X-ray diffraction measurements were performed at the Advanced Photon Source in order to study the dynamic deformation behavior of the specimens after ion irradiation damage. In-situ X-ray measurements taken during tensile testing of the ion-irradiated MA957 revealed a difference in loading behavior between the irradiated and un-irradiated regions of the specimen. At equivalent applied stresses, lower lattice strains were found in the radiation-damaged region than those in the un-irradiated region. This might be associated with a higher level of Type II stresses as a result of radiation hardening. The study has demonstrated the feasibility of combining high-energy ion radiation and high-energy synchrotron X-ray diffraction to study materials' radiation damage in a dynamic manner.

  9. Investigation of high-energy ion-irradiated MA957 using synchrotron radiation under in-situ tension

    DOE PAGES

    Mo, Kun; Yun, Di; Miao, Yinbin; ...

    2016-01-02

    In this paper, an MA957 oxide dispersion-strengthened (ODS) alloy was irradiated with high-energy ions in the Argonne Tandem Linac Accelerator System. Fe ions at an energy of 84 MeV bombarded MA957 tensile specimens, creating a damage region similar to 7.5 μm in depth; the peak damage (similar to 40 dpa) was estimated to be at similar to 7 μm from the surface. Following the irradiation, in-situ high-energy X-ray diffraction measurements were performed at the Advanced Photon Source in order to study the dynamic deformation behavior of the specimens after ion irradiation damage. In-situ X-ray measurements taken during tensile testing ofmore » the ion-irradiated MA957 revealed a difference in loading behavior between the irradiated and un-irradiated regions of the specimen. At equivalent applied stresses, lower lattice strains were found in the radiation-damaged region than those in the un-irradiated region. This might be associated with a higher level of Type II stresses as a result of radiation hardening. The study has demonstrated the feasibility of combining high-energy ion radiation and high-energy synchrotron X-ray diffraction to study materials' radiation damage in a dynamic manner.« less

  10. Investigation of High-Energy Ion-Irradiated MA957 Using Synchrotron Radiation under In-Situ Tension

    PubMed Central

    Mo, Kun; Yun, Di; Miao, Yinbin; Liu, Xiang; Pellin, Michael; Almer, Jonathan; Park, Jun-Sang; Stubbins, James F.; Zhu, Shaofei; Yacout, Abdellatif M.

    2016-01-01

    In this study, an MA957 oxide dispersion-strengthened (ODS) alloy was irradiated with high-energy ions in the Argonne Tandem Linac Accelerator System. Fe ions at an energy of 84 MeV bombarded MA957 tensile specimens, creating a damage region ~7.5 μm in depth; the peak damage (~40 dpa) was estimated to be at ~7 μm from the surface. Following the irradiation, in-situ high-energy X-ray diffraction measurements were performed at the Advanced Photon Source in order to study the dynamic deformation behavior of the specimens after ion irradiation damage. In-situ X-ray measurements taken during tensile testing of the ion-irradiated MA957 revealed a difference in loading behavior between the irradiated and un-irradiated regions of the specimen. At equivalent applied stresses, lower lattice strains were found in the radiation-damaged region than those in the un-irradiated region. This might be associated with a higher level of Type II stresses as a result of radiation hardening. The study has demonstrated the feasibility of combining high-energy ion radiation and high-energy synchrotron X-ray diffraction to study materials’ radiation damage in a dynamic manner. PMID:28787819

  11. Variation in the electrical properties of ion beam irradiated cadmium selenate nanowires

    SciTech Connect

    Chauhan, R. P. Narula, Chetna; Panchal, Suresh

    2016-05-23

    The key feature of nanowires consists in the pronounced change in properties induced by the low dimensionality and high surface to volume ratio. The study of electrical transport properties of nanowires is important for electronic device applications. Energetic ions create changes, which may be structural or chemical, in a material along their track and these changes might alter the material’s properties. The demand of the modern technology is to understand the effect of radiation on the different properties of the material for its further applications. The present study is on the high-energy Nickel ion beam (160 MeV Ni{sup +12}) induced modifications in the electrical and structural properties of the cadmium selenate nanowires. An enhancement in the electrical conductivity of irradiated wires was observed as the ion fluence was increased especially in the forward I–V characteristics. The creation of defects by ion irradiation and the synergy of the ions during their passage in the sample with the intrinsic charge carriers may be responsible for the variation in the transport properties of the irradiated nanowires.

  12. Dependence of Ion Energy on PTFE Surface Modification Effect by Nitrogen Ion Irradiation

    NASA Astrophysics Data System (ADS)

    Nakayama, Akihiko; Iwao, Toru; Yumoto, Motoshige

    PTFE (Poly-tetra-fluoro-ethylene) has superior characteristic. But, it has low adhesion force. In order to improve adhesion force, we have studied on surface modification of PTFE by using discharge under high E/n (E:electric field, n:particle density) condition in nitrogen. From the results, it was deduced that ion energy around 40 eV is effective for polar groups introduction. In addition, treated surface unevenness did not increase compared with the untreated one. Then, we performed nitrogen ion irradiation by changing ion energy. From the results, it is shown that low ion energy is effective for polar groups introduction. It is also shown that high energy ion suppresses surface roughness. Thus, we measured surface energy and composition of samples irradiated by high and low energy ions. When ion with 30 eV was irradiated for 5 minute and following it ion with 1060 eV was irradiated for 10 second, many polar groups were introduced and surface unevenness was kept at the untreatment level. From the results by XPS (X-ray Photoelectron Spectroscopy) analysis and FT-IR (Fourier transform Infrared Spectroscopy) analysis by using the ATR (Attenuated Total Reflection) method, it was confirmed that polar groups of oxygen component and cross-linked structure via nitrogen or carbon was introduced at the surface.

  13. Morphological change of self-organized protrusions of fluoropolymer surface by ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Kitamura (Ogawa), Akane; Kobayashi, Tomohiro; Satoh, Takahiro; Koka, Masashi; Kamiya, Tomihiro; Suzuki, Akihiro; Terai, Takayuki

    2013-07-01

    Polytetrafluoroethylene (PTFE) and fluorinated ethylene propylene (FEP) are typical fluoropolymers displaying several desirable technological properties such as electrical insulation and high chemical resistance. When their surfaces are irradiated with ion beams, dense micro-protrusions formed after the emergence and spread of micropores across the entire irradiated area, allowing culture cells to spread on the top of the protrusions. In this study, we investigate the morphological changes introduced in the fluoropolymer surfaces by ion beams as the energy of the beams is increased. When an FEP sample was irradiated with a nitrogen ion beam with an energy of less than 350 keV at 1.0 μA/cm2, protrusions were formed with a density between 2 × 107/cm2 and 2 × 108/cm2. However, at energies higher than 350 keV, the protrusions became sparse, and the density dropped to 5 × 102/cm2. Protrusions appeared sporadically during irradiation at high energies, and the top of the protrusions appeared as spots inside the sample, which were difficult to etch and became elongated as the erosion of the surface progressed. Erosion was caused by sputtering of FEP molecules and evaporation at notably elevated temperatures on the surface. Analysis based on attenuated total reflectance/Fourier transform infrared spectroscopy showed the presence of Cdbnd C bonds as well as -COOH, -Cdbnd O, and -OH bonds on all irradiated samples. Their concentration on the surface densely covered with micro-protrusions was higher than that on the surface with sparse protrusions after irradiation at energies exceeding 350 keV. Thus, we determined a suitable range for the ion energy for creating FEP surfaces densely covered with protrusions.

  14. Fluence dependent oscillatory amorphization and recrystallization in ion irradiation

    NASA Astrophysics Data System (ADS)

    Banu, Nasrin; Satpati, B.; Dev, B. N.

    2017-09-01

    Ion-beam-induced amorphization and recrystallization are well-known phenomena. At a constant ion flux, there is a substrate temperature TR such that, for T < TR the irradiation produces amorphization, whereas for T > TR, it produces recrystallization. However, both the processes do not happen at a given substrate temperature. Here we present a novel phenomenon of ion fluence dependent oscillatory amorphization and recrystallization in silicon at room temperature in a Si(5 nm)/Ni(15 nm)/Si system. Before the deposition of Ni on Si, a buffer Si layer was deposited on the Si substrate. Ion irradiation was carried out with 1 MeV Si+ ions in the fluence range 1 × 1014-3 × 1017 ions/cm2. At a fluence of 5 × 1016 ions/cm2, Si is amorphous up to a depth of ∼1.4 μm. However, at a fluence of 1 × 1017 ions/cm2 two narrow bands of recrystallized (rc) Si are formed within the amorphized Si. At 2 × 1017 ions/cm2 these rc-Si bands become amorphous again. At 3 × 1017 ions/cm2 the broader rc band reappears. This oscillatory amorphization/recrystallization behaviour is Ni-mediated. Energy dispersive X-ray map of Ni shows Ni accumulation at the top of the rc-Si bands. The top of the broader rc band is actually the buffer-Si/substrate-Si interface. TRIM simulation shows the appearance of a Ni-displacement-induced vacancy peak at the position of the narrow rc-Si band. Accumulation of Ni in these regions is associated with the recrystallization process. The Ni layer, with incorporation of Si, also passes through amorphization and recrystallization. At the highest fluence η-NiSi nanocrystals are formed in the Ni layer.

  15. Characterization of swift heavy ion irradiation damage in ceria

    DOE PAGES

    Yablinsky, Clarissa A.; Devanathan, Ram; Pakarinen, Janne; ...

    2015-03-04

    Swift heavy ion induced radiation damage is investigated for ceria (CeO2), which serves as a UO2 fuel surrogate. Microstructural changes resulting from an irradiation with 940 MeV gold ions of 42 keV/nm electronic energy loss are investigated by means of electron microscopy accompanied by electron energy loss spectroscopy showing that there exists a small density reduction in the ion track core. While chemical changes in the ion track are not precluded, evidence of them was not observed. Classical molecular dynamics simulations of thermal spikes in CeO2 with an energy deposition of 12 and 36 keV/nm show damage consisting of isolatedmore » point defects at 12 keV/nm, and defect clusters at 36 keV/nm, with no amorphization at either energy. Furthermore, inferences are drawn from modeling about density changes in the ion track and the formation of interstitial loops that shed light on features observed by electron microscopy of swift heavy ion irradiated ceria.« less

  16. Characterization of swift heavy ion irradiation damage in ceria

    SciTech Connect

    Yablinsky, Clarissa A.; Devanathan, Ram; Pakarinen, Janne; Gan, Jian; Severin, Daniel; Trautmann, Christina; Allen, Todd R.

    2015-03-04

    Swift heavy ion induced radiation damage is investigated for ceria (CeO2), which serves as a UO2 fuel surrogate. Microstructural changes resulting from an irradiation with 940 MeV gold ions of 42 keV/nm electronic energy loss are investigated by means of electron microscopy accompanied by electron energy loss spectroscopy showing that there exists a small density reduction in the ion track core. While chemical changes in the ion track are not precluded, evidence of them was not observed. Classical molecular dynamics simulations of thermal spikes in CeO2 with an energy deposition of 12 and 36 keV/nm show damage consisting of isolated point defects at 12 keV/nm, and defect clusters at 36 keV/nm, with no amorphization at either energy. Furthermore, inferences are drawn from modeling about density changes in the ion track and the formation of interstitial loops that shed light on features observed by electron microscopy of swift heavy ion irradiated ceria.

  17. Characterization of swift heavy ion irradiation damage in ceria

    SciTech Connect

    Yablinsky, Clarissa A.; Devanathan, Ram; Pakarinen, Janne; Gan, Jian; Severin, Daniel; Trautmann, Christina; Allen, Todd R.

    2015-03-04

    Swift heavy ion induced radiation damage is investigated for ceria (CeO2), which serves as a UO2 fuel surrogate. Microstructural changes resulting from an irradiation with 940 MeV gold ions of 42 keV/nm electronic energy loss are investigated by means of electron microscopy accompanied by electron energy loss spectroscopy showing that there exists a small density reduction in the ion track core. While chemical changes in the ion track are not precluded, evidence of them was not observed. Classical molecular dynamics simulations of thermal spikes in CeO2 with an energy deposition of 12 and 36 keV/nm show damage consisting of isolated point defects at 12 keV/nm, and defect clusters at 36 keV/nm, with no amorphization at either energy. Inferences are drawn from modeling about density changes in the ion track and the formation of interstitial loops that shed light on features observed by electron microscopy of swift heavy ion irradiated ceria.

  18. Variation of deep electron traps created by. gamma. irradiation of GaAs

    SciTech Connect

    Hashizume, T. ); Hasegawa, H. )

    1990-11-01

    The effect of {gamma} irradiation on deep electron states in liquid encapsulated Czochralski (LEC) grown GaAs has been investigated by deep-level transient spectroscopy (DLTS) and photocapacitance measurements. With {gamma} rays of 2{times}10{sup 8} R, EL6 was reduced in concentration by a factor of 3--5, whereas EL3 was increased about one order of magnitude, as compared with those in as-grown material. In addition to {ital E} traps that were previously reported in electron-irradiated material, two new traps were observed near the surface region. From their concentration profiles and annealing behavior, the new traps were most likely created by the interaction of the primary irradiation-induced defects with the grown-in defects. In contrast to these results, neither the DLTS spectrum nor the metastable behavior of EL2 was affected by {gamma} irradiation.

  19. Late degeneration in rabbit tissues after irradiation by heavy ions

    NASA Technical Reports Server (NTRS)

    Lett, J. T.; Cox, A. B.; Keng, P. C.; Lee, A. C.; Su, C. M.; Bergtold, D. S.

    1980-01-01

    Results are presented for investigations of the late effects of heavy-ion irradiation on rabbit tissues which were undertaken to assess the hazards associated with the long-term exposure of humans to heavy ions in space during such activities as the construction of solar power stations or voyages to Mars. White rabbits approximately six weeks old were exposed to various doses of collimated beams of 400-MeV/n Ne ions, 570 MeV/n Ar ions and Co-60 gamma rays directed through both eyes, and the responses of the various tissues (hair follicles, skin, cornea, lens, retina, Harderian glands, bone and forebrain) were examined. Proliferating tissues are found to exhibit high damage levels in the early and late periods following irradiation, while terminally differentiating tissues repond to radiation most intensely in the late period, years after irradiation, with no intermediate recovery. The results obtained from rabbits are used to predict the occurrence of late tissue degeneration in the central nervous system, terminally differentiating systems and stem cells of humans one or more decades following exposure to radiation levels anticipated during long-duration space flights. The studies also indicate that tissues may be prematurely aged in the sense that tissue life spans may be shortened without the development of malignancies.

  20. An infrared study of pure and ion irradiated frozen formamide

    NASA Astrophysics Data System (ADS)

    Brucato, J. R.; Baratta, G. A.; Strazzulla, G.

    2006-08-01

    Context.The chemical evolution of formamide (HCONH2), a molecule of astrobiological interest that has been tentatively identified in interstellar ices and in cometary coma, has been studied in laboratory under simulated astrophysical conditions such as ion irradiation at low temperature.Aims.To evaluate the abundances of formamide observed in space or in laboratory, the integrated absorbances for all the principal IR features of frozen amorphous pure formamide deposited at 20 K were measured. Further evidence that energetic processing of ices occurring in space is extremely relevant both to astrochemistry and to astrobiology has been found, showing that new molecular species are synthesized by ion irradiation at a low temperature.Methods.Pure formamide were deposited at 20 K and IR transmission spectra measured for different ice thicknesses. The ice thickness was derived by looking at the interference pattern (intensity versus time) of a He-Ne laser beam reflected at an angle of 45 deg by the vacuum-film and film-substrate interfaces. Samples of formamide ice were irradiated with 200 keV H+ ions and IR spectra recorded at different ion fluences.Results.New molecules were synthesized among which are CO, CO2, N2O, isocyanic acid (HNCO), and ammonium cyanate (NH4^+OCN^-). Some of these species remain stable after warming up to room temperature.

  1. Late degeneration in rabbit tissues after irradiation by heavy ions

    NASA Technical Reports Server (NTRS)

    Lett, J. T.; Cox, A. B.; Keng, P. C.; Lee, A. C.; Su, C. M.; Bergtold, D. S.

    1980-01-01

    Results are presented for investigations of the late effects of heavy-ion irradiation on rabbit tissues which were undertaken to assess the hazards associated with the long-term exposure of humans to heavy ions in space during such activities as the construction of solar power stations or voyages to Mars. White rabbits approximately six weeks old were exposed to various doses of collimated beams of 400-MeV/n Ne ions, 570 MeV/n Ar ions and Co-60 gamma rays directed through both eyes, and the responses of the various tissues (hair follicles, skin, cornea, lens, retina, Harderian glands, bone and forebrain) were examined. Proliferating tissues are found to exhibit high damage levels in the early and late periods following irradiation, while terminally differentiating tissues repond to radiation most intensely in the late period, years after irradiation, with no intermediate recovery. The results obtained from rabbits are used to predict the occurrence of late tissue degeneration in the central nervous system, terminally differentiating systems and stem cells of humans one or more decades following exposure to radiation levels anticipated during long-duration space flights. The studies also indicate that tissues may be prematurely aged in the sense that tissue life spans may be shortened without the development of malignancies.

  2. Elastic wave from fast heavy ion irradiation on solids

    NASA Astrophysics Data System (ADS)

    Kambara, T.; Kageyama, K.; Kanai, Y.; Kojima, T. M.; Nanai, Y.; Yoneda, A.; Yamazaki, Y.

    2002-06-01

    To study the time-dependent mechanical effects of fast heavy ion irradiations, we have irradiated various solids by a short-bunch beam of 95 MeV/u Ar ions and observed elastic waves generated in the bulk. The irradiated targets were square-shaped plates of poly-crystals of metals (Al and Cu), invar alloy, ceramic (Al 2O 3), fused silica (SiO 2) and single crystals of KC1 and LiF with a thickness of 10 mm. The beam was incident perpendicular to the surface and all ions were stopped in the target. Two piezo-electric ultrasonic sensors were attached to the surface of the target and detected the elastic waves. The elastic waveforms as well as the time structure and intensity of the beam bunch were recorded for each shot of a beam bunch. The sensor placed opposite to the beam spot recorded a clear waveform of the longitudinal wave across the material, except for the invar and fused silica targets. From its propagation time along with the sound velocity and the thickness of the target, the depth of the wave source was estimated. The result was compared with ion ranges calculated for these materials by TRIM code.

  3. Magnetic properties of graphite irradiated with MeV ions

    SciTech Connect

    Ramos, M. A.; Munoz-Martin, A.; Climent-Font, A.; Barzola-Quiquia, J.; Esquinazi, P.; Garcia-Hernandez, M.

    2010-06-01

    We have studied the change in the magnetic properties produced on highly oriented pyrolytic graphite samples by irradiation of H, C, and N ions in the mega-electron-volt energy range. The use of specially made sample holders for the magnetic measurements provided high reproducibility allowing us to obtain directly the irradiation effects without any corrections or subtractions. Our results show that three magnetic phenomena are triggered by the defects produced by the irradiation, namely, Curie-type paramagnetism, ferromagnetism and an anomalous paramagnetic state that appears as precursor of the magnetic ordered state. Using SRIM simulations to estimate the amount of vacancies produced by the irradiation, the Curie-type paramagnetic response indicates an effective Bohr magneton number per nominally produced vacancy p=0.27+-0.02mu{sub B}. Direct measurements of the surface sample temperature during irradiation and the decrease in the (as-received) paramagnetic as well as ferromagnetic contributions after irradiation indicate that self-heating is one of the causes for small yield of ferromagnetism. Taking into account the hydrogen distribution in the virgin samples, the obtained results indicate that the induced ferromagnetism appears when the average vacancy distance is {approx}2 nm in the near surface region.

  4. Thermal property tuning in aligned carbon nanotube films and random entangled carbon nanotube films by ion irradiation

    SciTech Connect

    Wang, Jing; Chen, Di; Wang, Xuemei; Bykova, Julia S.; Zakhidov, Anvar A.; Shao, Lin

    2015-10-12

    Ion irradiation effects on thermal property changes are compared between aligned carbon nanotube (A-CNT) films and randomly entangled carbon nanotube (R-CNT) films. After H, C, and Fe ion irradiation, a focusing ion beam with sub-mm diameter is used as a heating source, and an infrared signal is recorded to extract thermal conductivity. Ion irradiation decreases thermal conductivity of A-CNT films, but increases that of R-CNT films. We explain the opposite trends by the fact that neighboring CNT bundles are loosely bonded in A-CNT films, which makes it difficult to create inter-tube linkage/bonding upon ion irradiation. In a comparison, in R-CNT films, which have dense tube networking, carbon displacements are easily trapped between touching tubes and act as inter-tube linkage to promote off-axial phonon transport. The enhancement overcomes the phonon transport loss due to phonon-defect scattering along the axial direction. A model is established to explain the dependence of thermal conductivity changes on ion irradiation parameters including ion species, energies, and current.

  5. Comparison of total dose effects on SiGe heterojunction bipolar transistors induced by different swift heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Sun, Ya-Bin; Fu, Jun; Xu, Jun; Wang, Yu-Dong; Zhou, Wei; Zhang, Wei; Cui, Jie; Li, Gao-Qing; Liu, Zhi-Hong

    2014-11-01

    The degradations in NPN silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) were fully studied in this work, by means of 25-MeV Si, 10-MeV Cl, 20-MeV Br, and 10-MeV Br ion irradiation, respectively. Electrical parameters such as the base current (IB), current gain (β), neutral base recombination (NBR), and Early voltage (VA) were investigated and used to evaluate the tolerance to heavy ion irradiation. Experimental results demonstrate that device degradations are indeed radiation-source-dependent, and the larger the ion nuclear energy loss is, the more the displacement damages are, and thereby the more serious the performance degradation is. The maximum degradation was observed in the transistors irradiated by 10-MeV Br. For 20-MeV and 10-MeV Br ion irradiation, an unexpected degradation in IC was observed and Early voltage decreased with increasing ion fluence, and NBR appeared to slow down at high ion fluence. The degradations in SiGe HBTs were mainly attributed to the displacement damages created by heavy ion irradiation in the transistors. The underlying physical mechanisms are analyzed and investigated in detail.

  6. Doping of Ion Irradiated Polyethylenterephtalate from Water Solution of LiCl

    NASA Astrophysics Data System (ADS)

    Hnatowicz, V.; Vacík, J.; Ervená, J.; Vorík, V.; Rybka, V.; Fink, D.; Klett, R.

    1997-02-01

    Polyethylenterephtalate foils (10 m thick with the density of = 1.3 g cm - 3) were irradiated with 150 keV Ar+ ions to fluences from 5×1011 to 1×1015 cm - 2 and one year after the irradiation they were exposed to a 5 M water solution of LiCl at the boiling point for times ranging from 15 s up to 8 h. The depth profiles of incorporated Li atoms as a function of the ion fluence and the doping time were determined using the neutron depth profiling technique based on the 6Li(nth, α)3H nuclear reaction. The Li content in the 600 nm thick surface layer achieves saturation very rapidly, already after 15 s doping time, and it exhibits a local, pronounced maximum at 2 or 4 h doping times for the specimens irradiated to fluences below and above 5×1014 cm - 2, respectively. The concentration depth profiles of incorporated Li atoms consist of a pronounced surface component, obviously connected with radiation damages created by the ion irradiation and a long inward tail which is due to regular diffusion in pristine polymer. As a function of ion fluence, the Li content increases up to the fluence of 5×1013 cm - 2 and then declines in most cases. The surface component of the Li depth profiles changes dramatically with increasing ion fluence from bell-shaped ones for fluences below 5×1014 cm×2 to those characterized by a depleted surface layer and a rather sharp concentration maximum at depths significantly exceeding the calculated ion projected range.

  7. Collisional activation of ions by off-resonance irradiation in ion cyclotron resonance spectrometry

    NASA Astrophysics Data System (ADS)

    Shin, Seung Koo; Han, Seung-Jin; Seo, Jongcheol

    2009-06-01

    Collisional activation of ions in the ion cyclotron resonance (ICR) cell by short off-resonance burst irradiation (ORBI) was studied by time-resolved photodissociation of the meta-bromotoluene radical cation. Off-resonance chirp or single-frequency burst was applied for 2 ms to the probe ion in the presence of Ar buffer gas. The amount of internal energy imparted to the probe ion by collision under ORBI was precisely determined by time-resolved photodissociation spectroscopy. The rate of unimolecular dissociation of the probe ion following the photolysis at 532 nm was measured by monitoring the real-time appearance of the C7H7+ product ion. The internal energy of the probe ion was extracted from the known rate-energy curve. To help understand the collisional activation of an ion under ORBI, we simulated the radial trajectory of the ion using Green's method. The calculated radial kinetic energy was converted to the collision energy in the center-of-mass frame, and the collision frequency was estimated by using a reactive hard-sphere collision model with an ion-induced dipole potential. Both experiments and trajectory simulations suggest that chirp irradiation leads to less collisional activation of ions than other waveforms.

  8. He ion irradiation damage in Al/Nb multilayers

    SciTech Connect

    Li Nan; Anderoglu, O.; Zhang, X.; Martin, M. S.; Shao, L.; Misra, A.; Wang, H.

    2009-06-15

    We investigate the evolution of microstructure and mechanical properties of sputter-deposited Al/Nb multilayers with miscible fcc/bcc type interface and individual layer thickness, h, of 1-200 nm, subjected to helium ion irradiations: 100 keV He{sup +} ions and a fluence of 6x10{sup 16}/cm{sup 2}. Helium bubbles, 1-2 nm in diameter, are observed. When h is greater than 25 nm, hardnesses of irradiated multilayers barely change, whereas radiation hardening is more significant at smaller h. Transmission electron microscopy and scanning transmission electron microscopy studies reveal the formation of a thin layer of Nb{sub 3}Al intermetallic phase along the Al/Nb interface as a consequence of radiation induced intermixing. The dependence of radiation hardening on h is interpreted by using a composite model considering the formation of the hard Nb{sub 3}Al intermetallic layer.

  9. Tunable nanometer electrode gaps by MeV ion irradiation

    SciTech Connect

    Cheang-Wong, J.-C.; Narumi, K.; Schuermann, G. M.; Aziz, M. J.; Golovchenko, J. A.

    2012-04-09

    We report the use of MeV ion-irradiation-induced plastic deformation of amorphous materials to fabricate electrodes with nanometer-sized gaps. Plastic deformation of the amorphous metal Pd{sub 80}Si{sub 20} is induced by 4.64 MeV O{sup 2+} ion irradiation, allowing the complete closing of a sub-micrometer gap. We measure the evolving gap size in situ by monitoring the field emission current-voltage (I-V) characteristics between electrodes. The I-V behavior is consistent with Fowler-Nordheim tunneling. We show that using feedback control on this signal permits gap size fabrication with atomic-scale precision. We expect this approach to nanogap fabrication will enable the practical realization of single molecule controlled devices and sensors.

  10. He ion irradiation damage to Al/Nb multilayers

    SciTech Connect

    Misra, Amit; Li, Nan; Martin, M S; Anderoglu, Osman; Shao, L; Wang, H; Zhang, X

    2009-01-01

    We investigated the evolution of microstructure and mechanical properties of sputter-deposited Al/Nb multilayers with individual layer thickness, h, of 1-200 nm, subjected to helium ion irradiations: 100 keV He{sup +} ions with a dose of 6 x 10{sup 16}/cm{sup 2}. Helium bubbles, 1-2 nm in diameter, were observed. When h is greater than 25 nm, hardnesses of irradiated multilayers barely change, whereas radiation hardening is more significant at smaller h. Transmission electron microscopy and scanning transmission electron microscopy studies reveal the formation of a thin layer of Nb{sub 3}Al intermetallic along the Al/Nb interface as a consequence of radiation induced intermixing. The dependence of radiation hardening on h is interpreted by using a composite model considering the formation of the hard Nb{sub 3}Al intermetallic layer.

  11. Mutagenic effects of heavy ion irradiation on rice seeds

    NASA Astrophysics Data System (ADS)

    Xu, Xue; Liu, Binmei; Zhang, Lili; Wu, Yuejin

    2012-11-01

    Three varieties of rice seeds were subjected to irradiation using low-energy and medium-energy ions. The damage and mutations induced by the ions were examined. In addition, genetic analysis and gene mapping of spotted leaf (spl) mutants were performed. Low-energy ions had no significant influence on germination, survival or seedling height, except for the survival of Nipponbare. Medium-energy ions had a significant influence on germination and survival but had no significant effect on seedling height. In the low-energy group, among 60,000 M2 plants, 2823 putative morphological mutants were found, and the mutation frequency was approximately 4.71%. In the medium-energy group, 3132 putative morphological mutants were found, and the mutation frequency was approximately 5.22%. Five spl mutants (spl29-spl33) were obtained by ion irradiation, and the heredity of the spl mutants was stable. The characteristics of the spl mutants were found, by genetic analysis and preliminary mapping, to be controlled by a single recessive gene, and spl30 and spl33 were found to be new lesion-mimic mutants.

  12. Temperature measurements during high flux ion beam irradiations

    SciTech Connect

    Crespillo, Miguel L.; Graham, Joseph T.; Zhang, Yanwen; Weber, William J.

    2016-02-16

    A systematic study of the ion beam heating effect was performed in a temperature range of –170 to 900 °C using a 10 MeV Au3+ ion beam and a Yttria stabilized Zirconia (YSZ) sample at a flux of 5.5 × 1012 cm–2 s–1. Different geometric configurations of beam, sample, thermocouple positioning, and sample holder were compared to understand the heat/charge transport mechanisms responsible for the observed temperature increase. The beam heating exhibited a strong dependence on the background (initial) sample temperature with the largest temperature increases occurring at cryogenic temperatures and decreasing with increasing temperature. Comparison with numerical calculations suggests that the observed heating effect is, in reality, a predominantly electronic effect and the true temperature rise is small. Furthermore, a simple model was developed to explain this electronic effect in terms of an electrostatic potential that forms during ion irradiation. Such an artificial beam heating effect is potentially problematic in thermostated ion irradiation and ion beamanalysis apparatus, as the operation of temperature feedback systems can be significantly distorted by this effect.

  13. Temperature measurements during high flux ion beam irradiations

    DOE PAGES

    Crespillo, Miguel L.; Graham, Joseph T.; Zhang, Yanwen; ...

    2016-02-16

    A systematic study of the ion beam heating effect was performed in a temperature range of –170 to 900 °C using a 10 MeV Au3+ ion beam and a Yttria stabilized Zirconia (YSZ) sample at a flux of 5.5 × 1012 cm–2 s–1. Different geometric configurations of beam, sample, thermocouple positioning, and sample holder were compared to understand the heat/charge transport mechanisms responsible for the observed temperature increase. The beam heating exhibited a strong dependence on the background (initial) sample temperature with the largest temperature increases occurring at cryogenic temperatures and decreasing with increasing temperature. Comparison with numerical calculations suggestsmore » that the observed heating effect is, in reality, a predominantly electronic effect and the true temperature rise is small. Furthermore, a simple model was developed to explain this electronic effect in terms of an electrostatic potential that forms during ion irradiation. Such an artificial beam heating effect is potentially problematic in thermostated ion irradiation and ion beamanalysis apparatus, as the operation of temperature feedback systems can be significantly distorted by this effect.« less

  14. Metastable hydronium ions in UV-irradiated ice

    SciTech Connect

    Moon, Eui-Seong; Kang, Heon

    2012-11-28

    We show that the irradiation of UV light (10-11 eV) onto an ice film produces metastable hydronium (H{sub 3}O{sup +}) ions in the ice at low temperatures (53-140 K). Evidence of the presence of metastable hydronium ions was obtained by experiments involving adsorption of methylamine onto UV-irradiated ice films and hydrogen-deuterium (H/D) isotopic exchange reaction. The methylamine adsorption experiments showed that photogenerated H{sub 3}O{sup +} species transferred a proton to the methylamine arriving at the ice surface, thus producing the methyl ammonium ion, which was detected by low energy sputtering method. The H{sub 3}O{sup +} species induced the H/D exchange of water, which was monitored through the detection of water isotopomers on the surface by using the Cs{sup +} reactive ion scattering method. Thermal and temporal stabilities of H{sub 3}O{sup +} and its proton migration activity were examined. The lifetime of the hydronium ions in the amorphized ice was greater than 1 h at {approx}53 K and decreased to {approx}5 min at 140 K. Interestingly, a small portion of hydronium ions survived for an extraordinarily long time in the ice, even at 140 K. The average migration distance of protons released from H{sub 3}O{sup +} in the ice was estimated to be about two water molecules at {approx}54 K and about six molecules at 100 K. These results indicate that UV-generated hydronium ions can be efficiently stabilized in low-temperature ice. Such metastable hydronium ions may play a significant role in the acid-base chemistry of ice particles in interstellar clouds.

  15. Track Structure in DNA Irradiated with Heavy Ions

    SciTech Connect

    Bowman, Michael K.; Becker, David; Sevilla, Michael D.; Zimbrick, John D.

    2005-04-01

    The spatial properties of trapped radicals produced in heavy ion-irradiated solid DNA at 77 K have been probed using pulsed Electron Paramagnetic Double Resonance (PELDOR or DEER) techniques. Salmon testes DNA hydrated to twelve water molecules per nucleotide was irradiated with 40Ar ions of energy 100 MeV/nucleon and LET ranging from 300 to 400 keV/?. Irradiated samples were maintained at cryogenic temperature at all times. PELDOR measurements were made using a refocused echo detection sequence that allows dipolar interaction between trapped radicals to be observed. The EPR spectrum is attributed to electron loss/gain DNA base radicals and neutral carbon-centered radicals that likely arise from sugar damage. We find a radical concentration of 13.5*1018 cm-3 in the tracks and a track radius of 6.79 nm. The cross section of these tracks is 144 nm2 yielding a lineal radical density of 2.6 radicals/nm. Based upon the yields previously determined for particles having calculated LET values of 300-400 keV/mm and our measured lineal density, we obtain an LET of 270 keV/mm, which is in good agreement with the calculated range of values. These measurements of radical density and spatial extent provide the first direct experimental determination of track characteristics in irradiated DNA.

  16. Protective coatings preventing hydrogen desorption from titanium during ion irradiation

    NASA Astrophysics Data System (ADS)

    Evsin, A. E.; Begrambekov, L. B.; Dovganyuk, S. S.; Kaplevsky, A. S.; Shutikova, M. I.

    2017-05-01

    Effect of yttria and titanium nitride coatings on features of deuterium desorption from titanium layer is investigated. It is shown that both coatings significantly raise the temperature of maximum of deuterium thermal desorption from titanium under linear heating and prevent desorption under prolonged keeping at the operating temperature of a neutron tube target. However, under irradiation with ions of H2 + O2 plasma the barrier properties of titanium nitride appear to degrade.

  17. A Raman study of ion irradiated icy mixtures

    NASA Astrophysics Data System (ADS)

    Ferini, G.; Baratta, G. A.; Palumbo, M. E.

    2004-02-01

    In this paper we present a Raman study of pure CH4, H2O:CH4:N2 and CH3OH:N2 frozen films before and after ion irradiation at 12 K, 100 K and 300 K. By means of Raman spectroscopy, we monitor the structural evolution of each film, whose chemical and physical properties are deeply modified by the interaction with the ion beam. For the two methane containing samples, Raman spectra show that the initial ice is partially converted into a refractory residue, which under further irradiation evolves towards an amorphous carbon (AC) with a band near 1560 cm-1 (G line) and a shoulder at about 1360 cm-1 (D line). No evidence of the AC Raman band is seen in the spectra of the methanol-containing mixture. By means of Lorentzian fits, we have determined the specific parameters of the AC band (G and D line peak positions, widths and relative intensities) in our spectra after ion irradiation and we have compared them with the corresponding parameters of the band as observed in the spectra of 11 IDPs (Interplanetary Dust Particles). Here we present the experimental results and discuss their contribution to our knowledge of the origin and evolution of IDPs.

  18. A Raman study of ion irradiated icy mixtures

    NASA Astrophysics Data System (ADS)

    Baratta, G. A.; Ferini, G.; Palumbo, M. E.

    2003-04-01

    We present a Raman study of pure CH_4, H_2O:CH_4:N_2 and CH_3OH:N_2 frozen films before and after ion irradiation at low (12 K) and high (100 K or 300 K) temperature. By means of Raman spectroscopy, we monitor the structural evolution of each film, whose optical properties are deeply modified by the interaction with the ion beam. Raman spectra show that the sample is partially converted into a refractory residue, which under further irradiation evolves towards an amorphous carbon with a band near 1560 cm-1 (G line) and a shoulder at about 1360 cm-1 (D line). The specific parameters of this 'double-peaked' feature (peaks position, widths and relative intensities) can be used as diagnostic to classify different carbonaceous materials and infer information about their degree of order. We have compared these parameters for our samples (ion irradiated frozen films and residues), for different kinds of hydrogenated carbon grains and for some IDPs. We have found that IDPs have in general a narrower G line, which peaks at higher wavenumbers, than most of the laboratory samples here discussed. This implies that IDPs have a structure with a higher degree of order than that of our samples. Here we present the experimenal results and discuss their relevance to the study of the origin and evolution of IDPs.

  19. Ion irradiation of AZO thin films for flexible electronics

    NASA Astrophysics Data System (ADS)

    Boscarino, Stefano; Torrisi, Giacomo; Crupi, Isodiana; Alberti, Alessandra; Mirabella, Salvatore; Ruffino, Francesco; Terrasi, Antonio

    2017-02-01

    Aluminum doped Zinc oxide (AZO) is a promising transparent conductor for solar cells, displays and touch-screen technologies. The resistivity of AZO is typically improved by thermal annealing at temperatures not suitable for plastic substrates. Here we present a non-thermal route to improve the electrical and structural properties of AZO by irradiating the TCO films with O+ or Ar+ ion beams (30-350 keV, 3 × 1015-3 × 1016 ions/cm2) after the deposition on glass and flexible polyethylene naphthalate (PEN). X-ray diffraction, optical absorption, electrical measurements, Rutherford Backscattering Spectrometry and Atomic Force Microscopy evidenced an increase of the crystalline grain size and a complete relief of the lattice strain upon ion beam irradiation. Indeed, the resistivity of thin AZO films irradiated at room temperature decreased of two orders of magnitude, similarly to a thermal annealing at 400 °C. We also show that the improvement of the electrical properties does not simply depend on the strain or polycrystalline domain size, as often stated in the literature.

  20. Light ion irradiation for unfavorable soft tissue sarcoma

    SciTech Connect

    Linstadt, D.; Castro, J.R.; Phillips, T.L.; Petti, P.L.; Collier, J.M.; Daftari, I.; Schoethaler, R.; Rayner, A.

    1990-09-01

    Between 1978 and 1989, 32 patients with unfavorable soft tissue sarcoma underwent light ion (helium, neon) irradiation with curative intent at Lawrence Berkeley Laboratory. The tumors were located in the trunk in 22 patients and head and neck in 10. Macroscopic tumor was present in 22 at the time of irradiation. Two patients had tumors apparently induced by previous therapeutic irradiation. Follow-up times for surviving patients ranged from 4 to 121 months (median 27 months). The overall 3-year actuarial local control rate was 62%; the corresponding survival rate was 50%. The 3-year actuarial control rate for patients irradiated with macroscopic tumors was 48%, while none of the patients with microscopic disease developed local recurrence (100%). The corresponding 3-year actuarial survival rates were 40% (macroscopic) and 78% (microscopic). Patients with retroperitoneal sarcoma did notably well; the local control rate and survival rate were 64% and 62%, respectively. Complications were acceptable; there were no radiation related deaths, while two patients (6%) required operations to correct significant radiation-related injuries. These results appear promising compared to those achieved by low -LET irradiation, and suggest that this technique merits further investigation.

  1. Ion exchange in KTiOPO4 crystals irradiated by copper and hydrogen ions.

    PubMed

    Zhang, Ruifeng; Lu, Fei; Lian, Jie; Liu, Hanping; Liu, Xiangzhi; Lu, Qingming; Ma, Hongji

    2008-05-12

    Cs(+)-K+ ion exchanges were produced on KTiOPO4 crystals which is prior irradiated by Cu+ can H+ ions. The energy and dose of implanted Cu+ ions are 1.5 MeV and 0.5 x 10(14) ions/cm2, and that of H+ are 300 keV and 1 x 10(16) ions/cm2, respectively. The temperature of ions exchange is 430 degrees C, and the time range from 15 minutes to 30 minutes. The prism coupling method is used to measure the dark mode spectra of the samples. Compared with results of ion exchange on the sample without irradiations, both the number of guided mode and its corresponding effective refractive index are decreased. The experimental results indicate that the ion exchange rate closely related with the lattice damage and the damage layers formed in the depth of maximum nuclear energy deposition act as a barrier to block the ions diffuse into the sample and the concentration of defects can modify the speed of ion exchange..

  2. Heavy ion tracks in polycarbonate. Comparison with a heavy ion irradiated model compound (diphenyl carbonate)

    NASA Astrophysics Data System (ADS)

    Ferain, E.; Legras, R.

    1993-09-01

    The chemical modifications induced by energetic heavy ion irradiation of polycarbonate (PC) film are determined by GPC, HPLC, ESR, TGA, IR and UV spectrophotometry. The main results of the irradiation are creation of radicals, chain scission, cross-linking and appearance of new chemical groups in the main polymer chain. As far as the creation of new groups is concerned, they are determined by means of a model compound of PC: the diphenyl carbonate (DPC). The following compounds are identified after energetic heavy ion irradiation of DPC: salicylic acid, phenol, 4,4'-biphenol, 2,4'-biphenol, 2,2'-biphenol, 4-phenoxyphenol, 2-phenoxyphenol, phenyl ether, phenyl benzoate, phenyl salicylate, 2-phenylphenol and 2-phenoxyphenyl benzoate. A similarity between the heavy ion irradiation and a heat treatment has also been established with DPC. On the basis of these results, we try to give an explanation of the preferential attack along the tracks of the irradiated film. Also, an explanation of the well-known beneficial effect of an UV exposition of the irradiated film on the selectivity of this preferential chemical attack is suggested.

  3. Semiconducting Properties of Swift Au Ion-Irradiated ZnO Thin Films at Room Temperature

    NASA Astrophysics Data System (ADS)

    Kwon, Sera; Park, Hyun-Woo; Chung, Kwun-Bum

    2017-02-01

    The semiconducting properties of Au ion-irradiated ZnO thin films were investigated as a function of ion irradiation dose at room temperature. The Au ion irradiation was conducted with acceleration energy of 130 MeV in the ion dose range from 1 × 1011 to 5 × 1012 ions/cm2. The physical properties showed no change regardless of the Au ion irradiation dose; however, the electrical properties of Au ion-irradiated ZnO thin films changed, depending on the Au ion irradiation dose. The electronic structure drastically changed with the evolution of hybridized molecular orbital structure for the conduction band and band edge states below the conduction band. These remarkable changes in electronic structure correlate with changes in electrical properties, such as carrier concentration and mobility.

  4. Characterization of polymeric films subjected to lithium ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Groenewold, Gary S.; Cannon, W. Roger; Lessing, Paul A.; Avci, Recep; Deliorman, Muhammedin; Wolfenden, Mark; Akers, Doug W.; Jewell, J. Keith; Zuck, Larry D.

    2013-02-01

    Two different polymeric materials that are candidate materials for use as binders for mixed uranium-plutonium oxide nuclear fuel pellets were subjected to Li ion beam irradiation, in order to simulate intense alpha irradiation. The materials (a polyethylene glycol 8000 and a microcrystalline wax) were then analyzed using a combination of mass spectrometry (MS) approaches and X-ray photoelectron spectroscopy (XPS). Samples of the irradiated PEG materials were dissolved in H2O and then analyzed using electrospray ionization-MS, which showed the formation of a series of small oligomers in addition to intact large PEG oligomers. The small oligomers were likely formed by radiation-induced homolytic scissions of the C-O and C-C bonds, which furnish radical intermediates that react by radical recombination with Hrad and OHrad . Surface analysis using SIMS revealed a heterogeneous surface that contained not only PEG-derived polymers, but also hydrocarbon-based entities that are likely surface contaminants. XPS of the irradiated PEG samples indicated the emergence of different carbon species, with peak shifts suggesting the presence of sp2 carbon atoms. Analysis of the paraffinic film using XPS showed the emergence of oxygen on the surface of the sample, and also a broadening and shifting of the C1s peak, demonstrating a change in the chemistry on the surface. The paraffinic film did not dissolve in either H2O or a H2O-methanol solution, and hence the bulk of the material could not be analyzed using electrospray. However a series of oligomers was leached from the bulk material that produced ion series in the ESI-MS analyses that were identified octylphenyl ethoxylate oligomers. Upon Li ion bombardment, these shifted to a lower average molecular weight, but more importantly showed the emergence of three new ion series that are being formed as a result of radiation damage. Surface analysis of the paraffinic polymers using SIMS produced spectra that were wholly dominated by

  5. Characterization of polymeric films subjected to lithium ion beam irradiation

    SciTech Connect

    Gary S. Groenewold; W. Roger Cannon; Paul A. Lessing; Recep Avci; Muhammedin Deliorman; Mark Wolfenden; Doug W. Akers; J. Keith Jewell

    2013-02-01

    Two different polymeric materials that are candidate materials for use as binders for mixed uranium–plutonium oxide nuclear fuel pellets were subjected to Li ion beam irradiation, in order to simulate intense alpha irradiation. The materials (a polyethylene glycol 8000 and a microcrystalline wax) were then analyzed using a combination of mass spectrometry (MS) approaches and X-ray photoelectron spectroscopy (XPS). Samples of the irradiated PEG materials were dissolved in H2O and then analyzed using electrospray ionization-MS, which showed the formation of a series of small oligomers in addition to intact large PEG oligomers. The small oligomers were likely formed by radiation-induced homolytic scissions of the C–O and C–C bonds, which furnish radical intermediates that react by radical recombination with Hradical dot and OHradical dot. Surface analysis using SIMS revealed a heterogeneous surface that contained not only PEG-derived polymers, but also hydrocarbon-based entities that are likely surface contaminants. XPS of the irradiated PEG samples indicated the emergence of different carbon species, with peak shifts suggesting the presence of sp2 carbon atoms. Analysis of the paraffinic film using XPS showed the emergence of oxygen on the surface of the sample, and also a broadening and shifting of the C1s peak, demonstrating a change in the chemistry on the surface. The paraffinic film did not dissolve in either H2O or a H2O–methanol solution, and hence the bulk of the material could not be analyzed using electrospray. However a series of oligomers was leached from the bulk material that produced ion series in the ESI-MS analyses that were identified octylphenyl ethoxylate oligomers. Upon Li ion bombardment, these shifted to a lower average molecular weight, but more importantly showed the emergence of three new ion series that are being formed as a result of radiation damage. Surface analysis of the paraffinic polymers using SIMS produced spectra that were

  6. Ion irradiation damage in ilmenite under cryogenic conditions

    SciTech Connect

    Mitchell, J.N.; Yu, N.; Devanathan, R.; Sickafus, K.E.; Nastasi, M.A.; Nord, G.L. Jr.

    1996-11-01

    A natural single crystal of ilmenite was irradiated at 100 K with 200 keV Ar{sup 2+}. Rutherford backscattering spectroscopy and ion channeling with 2 MeV He{sup +} ions were used to monitor damage accumulation in the surface region of the implanted crystal. At an irradiation fluence of 1 {times} 10{sup 15} Ar{sup 2+} cm{sup {minus}2}, considerable near-surface He{sup +} ion dechanneling was observed, to the extent that ion yield from a portion of the aligned crystal spectrum reached the yield level of a random spectrum. This observation suggests that the near-surface region of the crystal was amorphized by the implantation. Cross-sectional transmission electron microscopy and electron diffraction on this sample confirmed the presence of a 150 mm thick amorphous layer. These results are compared to similar investigations on geikielite (MgTiO{sub 3}) and spinel (MgAl{sub 2}O{sub 4}) to explore factors that may influence radiation damage response in oxides.

  7. Ion irradiation damage in ilmenite at 100 K

    USGS Publications Warehouse

    Mitchell, J.N.; Yu, N.; Devanathan, R.; Sickafus, K.E.; Nastasi, M.A.; Nord, G.L.

    1997-01-01

    A natural single crystal of ilmenite (FeTiO3) was irradiated at 100 K with 200 keV Ar2+. Rutherford backscattering spectroscopy and ion channeling with 2 MeV He+ ions were used to monitor damage accumulation in the surface region of the implanted crystal. At an irradiation fluence of 1 ?? 1015 Ar2+/cm2, considerable near-surface He+ ion dechanneling was observed, to the extent that ion yield from a portion of the aligned crystal spectrum reached the yield level of a random spectrum. This observation suggests that the near-surface region of the crystal was amorphized by the implantation. Cross-sectional transmission electron microscopy and electron diffraction on this sample confirmed the presence of a 150 nm thick amorphous layer. These results are compared to similar investigations on geikielite (MgTiO3) and spinel (MgAl2O4) to explore factors that may influence radiation damage response in oxides.

  8. Ion irradiation damage in ilmenite at 100 K

    SciTech Connect

    Mitchell, J.N.; Yu, N.; Devanathan, R.; Sickafus, K.E.; Nastasi, M.A.; Nord, G.L. Jr.

    1997-10-01

    A natural single crystal of ilmenite (FeTiO{sub 3}) was irradiated at 100 K with 200 keV Ar{sup 2+}. Rutherford backscattering spectroscopy and ion channeling with MeV He{sup +} ions were used to monitor damage accumulation in the surface region of the implanted crystal. At an irradiation fluence of 1 {times} 10{sup 15} Ar{sup 2+} cm{sup {minus}2}, considerable near-surface He{sup +} ion dechanneling was observed, to the extent that ion yield from a portion of the aligned crystal spectrum reached the yield level of a random spectrum. This observation suggests that the near-surface region of the crystal was amorphized by the implantation. Cross-sectional transmission electron microscopy and electron diffraction on this sample confirmed the presence of a 150 nm thick amorphous layer. These results are compared to similar investigations on geikielite (MgTiO{sub 3}) and spinel (MgAl{sub 2}O{sub 4}) to explore factors that may influence radiation damage response in oxides.

  9. Study of ion-irradiated tungsten in deuterium plasma

    NASA Astrophysics Data System (ADS)

    Khripunov, B. I.; Gureev, V. M.; Koidan, V. S.; Kornienko, S. N.; Latushkin, S. T.; Petrov, V. B.; Ryazanov, A. I.; Semenov, E. V.; Stolyarova, V. G.; Danelyan, L. S.; Kulikauskas, V. S.; Zatekin, V. V.; Unezhev, V. N.

    2013-07-01

    Experimental study aimed at investigation of neutron induced damage influence on fusion reactor plasma facing materials is reported. Displacement damage was produced in tungsten by high-energy helium and carbon ions at 3-10 MeV. The reached level of displacement damage ranged from several dpa to 600 dpa. The properties of the irradiated tungsten were studied in steady-state deuterium plasma on the LENTA linear divertor simulator. Plasma exposures were made at 250 eV of ion energy to fluence 1021-1022 ion/сm2. Erosion dynamics of the damaged layer and deuterium retention were observed. Surface microstructure modifications and important damage of the 5 μm layer shown. Deuterium retention in helium-damaged tungsten (ERD) showed its complex behavior (increase or decrease) depending on implanted helium quantity and the structure of the surface layer.

  10. Reflection properties of hydrogen ions at helium irradiated tungsten surfaces

    NASA Astrophysics Data System (ADS)

    Doi, K.; Tawada, Y.; Lee, H. T.; Kato, S.; Tanaka, N.; Sasao, M.; Kisaki, M.; Nishiura, M.; Matsumoto, Y.; Kenmotsu, T.; Wada, M.; Ueda, Y.; Yamaoka, H.

    2016-02-01

    Nanostructured W surfaces prepared by He bombardment exhibit characteristic angular distributions of hydrogen ion reflection upon injection of 1 keV H+ beam. A magnetic momentum analyzer that can move in the vacuum chamber has measured the angular dependence of the intensity and the energy of reflected ions. Broader angular distributions were observed for He-irradiated tungsten samples compared with that of the intrinsic polycrystalline W. Both intensity and energy of reflected ions decreased in the following order: the polycrystalline W, the He-bubble containing W, and the fuzz W. Classical trajectory Monte Carlo simulations based on Atomic Collision in Amorphous Target code suggests that lower atom density near the surface can make the reflection coefficients lower due to increasing number of collisions.

  11. Investigations of Atomic Transport Induced by Heavy Ion Irradiation

    NASA Astrophysics Data System (ADS)

    Banwell, Thomas Clyde

    The mechanisms of atomic transport induced by ion irradiation generally fall into the categories of anisotropic or isotropic processes. Typical examples of these are recoil implantation and cascade mixing, respectively. We have measured the interaction of these processes in the mixing of Ti/SiO(,2)/Si, Cr/SiO(,2)/Si and Ni/SiO(,2)/Si multi-layers irradiated with Xe at fluences of 0.01 - 10 x 10('15)cm('-2). The fluence dependence of net metal transport into the underlying layers was measured with different thicknesses of SiO(,2) and different sample temperatures during irradiation (-196 to 500C). There is a linear dependence at low fluences. At high fluences, a square-root behavior predominates. For thin SiO(,2) layers (<20nm), the cross -over point depends on the SiO(,2) thickness. These results are readily interpreted in terms of competition between the flux of injected atoms and diffusion of the accumulating metal. The detailed analysis allows us to speculate on the role of chemical reaction kinetics in controlling the outcome of intra-cascade processes. There is no significant correlation between the reactivity of the metal with SiO(,2) and the amount of mixing observed when the irradiations are performed at 25C or below. The contribution from primary recoils is quite pronounced since the gross mixing is small. A significant correlation exists between the mixing and the energy deposited through elastic collisions F(,D ). Several models are examined in an attempt to describe the transport process in Ni/SiO(,2). It is likely that injection of Ni by secondary recoil implantation is primarily responsible for getting Ni into the SiO(,2). Secondary recoil injection is thought to scale with F(,D). Trends in the mixing rates indicate that the dominant mechanism for Ti and Cr could be the same as for Ni. The processes of atomic transport and phase formation clearly fail to be separable at higher temperatures. A positive correlation with chemical reactivity emerges at

  12. Probing Dense Plasmas Created from Intense Irradiation of Solid Target in the XUV Domain

    SciTech Connect

    Dobosz, S.; Doumy, G.; Stabile, H.; Monot, P.; Bougeard, M.; Reau, F.; Martin, Ph.

    2006-04-07

    In this paper, electronic density and temperature have been inferred from XUV transmission through hot solid-density plasma created by high temporal contrast femtosecond irradiation of thin plastic foil target in the 1018W/cm2 intensity range. High order harmonics generated in pulsed gas jet are used as a probe beam. The initial plasma parameters are determined with an accuracy better than 15% on the 100fs time scale, by comparison of the transmission of two consecutive harmonics.

  13. Swift heavy ion irradiation reduces porous silicon thermal conductivity

    NASA Astrophysics Data System (ADS)

    Massoud, M.; Canut, B.; Newby, P.; Frechette, L.; Chapuis, P. O.; Bluet, J. M.

    2014-12-01

    While the electrical conductivity of semiconductors can be easily changed over order of magnitudes (8 in silicon) by playing on the doping, the thermal conductivity (TC) control is a challenging issue. Nevertheless, numerous applications require TC control in Si down to 1 W m-1 K-1. Among them, there are thermal insulation requirements in MEMS, thermal management issues in 3D packaging or TC reduction for thermoelectric applications. Towards this end, the formation of nanoporous Si by electrochemical anodisation is efficient. Nevertheless, in this case the material is too fragile for MEMS application or even to withstand CMOS technological processes. In this work, we show that ion irradiation in the electronic regime is efficient for reducing TC in meso-porous Si (PSi), which is more mechanically robust than the nanoporous PSi. We have studied three different mass to energy ratios (238U at 110 MeV and 130Xe at 91 MeV and 29 MeV) with fluences ranging from 1012 cm-2 to 7 × 1013 cm-2. The sample properties, after irradiation, have been measured by infrared spectroscopy, Raman spectroscopy and scanning electron microscopy. The TC has been measured using scanning thermal microscopy. Although, bulk Si is insensitive to ion interaction in the electronic regime, we have observed the amorphisation of the PSi resulting in a TC reduction even for the low dose and energy. For the highest irradiation dose a very important reduction factor of four was obtained.

  14. Point defects reactions in ion irradiated SiC

    NASA Astrophysics Data System (ADS)

    Litrico, G.; Zimbone, M.; Baratta, G.; Marino, A. D. M.; Musumeci, P.; Calcagno, L.

    2010-10-01

    The defects produced in 4H-SiC epitaxial layers by irradiation with 800 keV C + were characterized by Low Temperature Photoluminescence. Ion beam irradiation induces the formation of some sharp lines in the wavelength range 428-441 nm of the photoluminescence spectra, that are typically known as "alphabet lines". These photoluminescence features are due to the recombination of excitons at structural defects. The photoluminescence results allow to single out two groups of peaks: the P 1 lines ( e-f-g) and the P 2 lines ( a-b-c-d), that exhibit a different trend with the ion fluence. The P 1 group intensity increases with fluence and tends to reach a saturation value at high fluence. The P 2 group yield, instead, exhibits a threshold at low fluence and then increases toward a saturation. Subsequent UV-laser irradiation decreases the intensity of the P 2 lines related to a change in the structural configuration of the associated defects.

  15. Microstructure of RERTR DU-Alloys Irradiated with Krypton Ions

    SciTech Connect

    J. Gan; D. Keiser; D. Wachs; B. Miller; T. Allen; M. Kirk; J. Rest

    2009-11-01

    Fuel development for reduced enrichment research and test reactor (RERTR) program is tasked with the development of new low enrichment uranium fuels that can be employed to replace existing high enrichment uranium fuels currently used in many research and test reactors worldwide. Radiation stability of the interaction product formed at fuel-matrix interface has a strong impact on fuel performance. Three depleted uranium alloys are cast that consist of the following 5 phases of interest to be investigated: U(Si,Al)3, (U,Mo)(Si,Al)3, UMo2Al20, U6Mo4Al43 and UAl4. Irradiation of TEM disc samples with 500 keV Kr ions at 200?C to high doses up to ~100 dpa were conducted using an intermediate voltage electron microscope equipped with an ion accelerator. The irradiated microstructure of the 5 phases is characterized using transmission electron microscopy. The results will be presented and the implication of the observed irradiated microstructure on the fuel performance will be discussed.

  16. Amorphization of SiC under ion and neutron irradiation

    NASA Astrophysics Data System (ADS)

    Snead, L. L.; Zinkle, S. J.; Hay, J. C.; Osborne, M. C.

    1998-05-01

    This paper presents results on the microstructure and physical properties of SiC amorphized by both ion and neutron irradiation. Specifically, 0.56 MeV Si ions have been implanted in single crystal 6H-SiC from ambient through >200°C and the critical threshold for amorphization was measured as a function of the irradiation temperature. From a high resolution transmission electron microscopy (HRTEM) study of the crystalline to amorphous transition region in these materials, elongated pockets of amorphous material oriented parallel to the free surface are observed. Single crystal 6H-SiC and hot pressed and sintered 6H and 3C SiC were neutron irradiated at approximately 70°C to a dose of ˜2.56 dpa causing complete amorphization. Property changes resulting from the crystal to amorphous transition in SiC include a density decrease of 10.8%, a hardness decrease from 38.7 to 21.0 GPa, and a decrease in elastic modulus from 528 to 292 GPa. Recrystallization of the amorphized, single crystal 6H-SiC appears to occur in two stages. In the temperature range of ˜800-1000°C, crystallites nucleate and slowly grow. In the temperature range of 1125-1150°C spontaneous nucleation and rapid growth of crystallites occur. It is further noted that amorphized 6H (alpha) SiC recrystallizes to highly faulted fcc (beta) SiC.

  17. Damage Processes In MgO Irradiated With Medium-energy Heavy Ions

    SciTech Connect

    Moll, Sandra J.; Zhang, Y.; Debelle, A.; Thome, Lionel; Crocombette, J.-P.; Zhu, Zihua; Jagielski, Jacek; Weber, William J.

    2015-04-01

    The micro-structural modifications produced in MgO single crystals exposed to medium-energy heavy ions (1.2-MeV Au) were investigated using Rutherford backscattering spectrometry in channeling geometry coupled to Monte-Carlo analyses, secondary ion mass spectrometry, X-ray diffraction and transmission electron microscopy. The damage accumulation and the elastic strain variation were interpreted in the framework of the multi-step damage accumulation (MSDA) model. Both build-ups follow a multi-step process similar to that recently observed for ion-irradiated yttria-stabilized zirconia (YSZ) single crystals. However, in MgO, an unexpectedly high disorder level occurs far beyond the theoretical damage distribution. These results strongly suggest that the migration of defects created in the near-surface layer is most likely at the origin of the broadening of the damage depth distribution in MgO.

  18. Damage processes in MgO irradiated with medium-energy heavy ions

    SciTech Connect

    Moll, Sandra; Zhang, Yanwen; Debelle, Aurelien; Thomé, Lionel; Crocombette, Jean-Paul; Zihua, Z.; Jagielski, Jacek; Weber, William J.

    2015-01-01

    In this research, the micro-structural modifications produced in MgO single crystals exposed to medium-energy heavy ions (1.2-MeV Au) were investigated using Rutherford backscattering spectrometry in channeling geometry coupled to Monte-Carlo analyses, secondary ion mass spectrometry, X-ray diffraction and transmission electron microscopy. The damage accumulation and the elastic strain variation were interpreted in the framework of the multi-step damage accumulation (MSDA) model. Both build-ups follow a multi-step process similar to that recently observed for ion-irradiated yttria-stabilized zirconia (YSZ) single crystals. However, in MgO, an unexpectedly high disorder level occurs far beyond the theoretical damage distribution. In conclusion, these results strongly suggest that the migration of defects created in the near-surface layer is most likely at the origin of the broadening of t he damage depth distribution in MgO.

  19. Stress-induced solid flow drives surface nanopatterning of silicon by ion-beam irradiation

    NASA Astrophysics Data System (ADS)

    Castro, M.; Gago, R.; Vázquez, L.; Muñoz-García, J.; Cuerno, R.

    2012-12-01

    Ion-beam sputtering (IBS) is known to produce surface nanopatterns over macroscopic areas on a wide range of materials. However, in spite of the technological potential of this route to nanostructuring, the physical process by which these surfaces self-organize remains poorly understood. We have performed detailed experiments of IBS on Si substrates that validate dynamical and morphological predictions from a hydrodynamic description of the phenomenon. We introduce a systematic approach to perform the experiments under conditions that guarantee the applicability of a linear description, helping to clarify the experimental framework in which theories should be tested. Among our results, the pattern wavelength is experimentally seen to depend almost linearly on ion energy, in agreement with existing results for other targets that are amorphous or become so under irradiation. Our work substantiates flow of a nanoscopically thin and highly viscous surface layer, driven by the stress created by the ion beam, as an accurate description of this class of systems.

  20. Effects of heavy-ion irradiation on FeSe

    NASA Astrophysics Data System (ADS)

    Sun, Yue; Park, Akiyoshi; Pyon, Sunseng; Tamegai, Tsuyoshi; Kambara, Tadashi; Ichinose, Ataru

    2017-03-01

    We report the effects of heavy-ion irradiation on FeSe single crystals by irradiating uranium up to a dose-equivalent matching field of Bϕ=16 T. Almost continuous columnar defects along the c axis with a diameter of ˜10 nm are confirmed by high-resolution transmission electron microscopy. Tc is found to be suppressed by introducing columnar defects at a rate of d Tc/d Bϕ˜-0.29 K/T, which is much larger than those observed in iron pnictides. This unexpected large suppression of Tc in FeSe is discussed in relation to the large diameter of the columnar defects as well as its unique band structure with a remarkably small Fermi energy. The critical current density is first dramatically enhanced with irradiation reaching a value over ˜2 ×105A /cm2 (˜5 times larger than that of the pristine sample) at 2 K (self-field) with Bϕ=2 T, then gradually suppressed with increasing Bϕ. The δ l pinning associated with charge-carrier mean-free-path fluctuations and the δ Tc pinning associated with spatial fluctuations of the transition temperature are found to coexist in the pristine FeSe, while the irradiation increases the contribution from δ l pinning and makes it dominant over Bϕ=4 T.

  1. Chlorine diffusion in uranium dioxide under heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Pipon, Y.; Bérerd, N.; Moncoffre, N.; Peaucelle, C.; Toulhoat, N.; Jaffrézic, H.; Raimbault, L.; Sainsot, P.; Carlot, G.

    2007-04-01

    The radiation enhanced diffusion of chlorine in UO2 during heavy ion irradiation is studied. In order to simulate the behaviour of 36Cl, present as an impurity in UO2, 37Cl has been implanted into the samples (projected range 200 nm). The samples were then irradiated with 63.5 MeV 127I at two fluxes and two temperatures and the chlorine distribution was analyzed by SIMS. The results show that, during irradiation, the diffusion of the implanted chlorine is enhanced and slightly athermal with respect to pure thermal diffusion. A chlorine gain of 10% accumulating near the surface has been observed at 510 K. This corresponds to the displacement of pristine chlorine from a region of maximum defect concentration. This behaviour and the mean value of the apparent diffusion coefficient found for the implanted chlorine, around 2.5 × 10-14 cm2 s-1, reflect the high mobility of chlorine in UO2 during irradiation with fission products.

  2. Swift heavy ion irradiation of Pt nanocrystals: I. shape transformation and dissolution

    SciTech Connect

    Giulian, R.; Araujo, L.L.; Kluth, P.; Sprouster, D.J.; Schnohr, C.S.; Byrne, A.P.; Ridgway, M.C.

    2014-09-24

    We report on the effects of swift heavy ion irradiation of embedded Pt nanocrystals (NCs), which change from spheres to prolate spheroids to rods upon irradiation. Using a broad range of ion irradiation energies and NC mean sizes we demonstrate that the elongation and dissolution processes are energy and size dependent, attaining comparable levels of shape transformation and dissolution upon a given energy density deposited in the matrix. The NC shape transformation remains operative despite discontinuous ion tracks in the matrix and exhibits a constant threshold size for elongation. In contrast, for ion irradiations in which the ion tracks are continuous, the threshold size for elongation is clearly energy dependent.

  3. Thermal evolution of microstructure in ion-irradiated GaN

    SciTech Connect

    Bae, In-Tae; Jiang, Weilin; Wang, Chong M.; Weber, William J.; Zhang, Yanwen

    2009-04-20

    The thermal evolution of the microstructure created by irradiation of a GaN single crystal with 2 MeV Au2+ ions at 150 K is characterized following annealing at 973 K using transmission electron microscopy. In the as-irradiated sample characterized at 300 K, Ga nanocrystals with the diamond structure, which is an unstable configuration for Ga, are directly observed together with nitrogen bubbles in the irradiation-induced amorphous layer. Upon thermal annealing, the thickness of the amorphous layer decreases by ~13.1 %, and nano-beam electron diffraction analysis indicates no evidence for residual Ga nanocrystals, but instead reveals a mixture of hexagonal and cubic GaN phases in the annealed sample. Nitrogen molecules, captured in the as-irradiated bubbles, appear to debond and react with the Ga nanocrystals during the thermal annealing to form crystalline GaN. In addition, electron energy loss spectroscopy measurements reveal an atomic volume change of 18.9 % for the as-irradiated amorphous layer relative to the virgin single crystal GaN. This relative swelling of the damaged layer reduces to 7.7 % after thermal annealing. Partial recrystallization and structural relaxation of the GaN amorphous state are believed responsible for the volume change.

  4. Raman spectroscopy of ion-irradiated interplanetary carbon dust analogues

    NASA Astrophysics Data System (ADS)

    Baratta, G. A.; Mennella, V.; Brucato, J. R.; Colangeli, L.; Leto, G.; Palumbo, M. E.; Strazzulla, G.

    Interplanetary dust particles (IDPs) and meteorites provide an unique opportunity to study extraterrestrial materials in laboratory. Different Raman studies have shown that most of IDPs exhibit the characteristic amorphous carbon Raman feature. Different degrees of order have been recognised in the amorphous carbon phase of IDPs testifying either to different origin or to different processing under different physical conditions (temperature, pressure etc.). This paper presents a comparison between the amorphous carbon Raman features of IDPs, and those of carbon dust analogues obtained in the laboratory by ion irradiation of carbon containing frozen gases and by arc discharge. We propose a possible mechanism able to induce an "evolution" of IDPs. In particular amorphous carbon with different degrees of order could be indicative of different irradiation doses by solar wind particles and fast solar protons, suffered by IDPs in the interplanetary medium before collection in the Earth's atmosphere.

  5. Rocket having barium release system to create ion clouds in the upper atmosphere

    NASA Technical Reports Server (NTRS)

    Lewis, B. W.; Stokes, C. S.; Smith, E. W.; Murphy, W. J. (Inventor)

    1974-01-01

    A chemical system for releasing a good yield of free barium atoms and barium ions to create ion clouds in the upper atmosphere and interplanetary space for the study of the geophysical properties of the medium is presented.

  6. Development of a facility for high-precision irradiation of cells with carbon ions

    SciTech Connect

    Goethem, Marc-Jan van; Niemantsverdriet, Maarten; Brandenburg, Sytze; Langendijk, Johannes A.; Coppes, Robert P.; Luijk, Peter van

    2011-01-15

    Purpose: Compared to photons, using particle radiation in radiotherapy reduces the dose and irradiated volume of normal tissues, potentially reducing side effects. The biological effect of dose deposited by particles such as carbon ions, however, differs from that of dose deposited by photons. The inaccuracy in models to estimate the biological effects of particle radiation remains the most important source of uncertainties in particle therapy. Improving this requires high-precision studies on biological effects of particle radiation. Therefore, the authors aimed to develop a facility for reproducible and high-precision carbon-ion irradiation of cells in culture. The combined dose nonuniformity in the lateral and longitudinal direction should not exceed {+-}1.5%. Dose to the cells from particles than other carbon ions should not exceed 5%. Methods: A uniform lateral dose distribution was realized using a single scatter foil and quadrupole magnets. A modulator wheel was used to create a uniform longitudinal dose distribution. The choice of beam energy and the optimal design of these components was determined using GEANT4 and SRIM Monte Carlo simulations. Verification of the uniformity of the dose distribution was performed using a scintillating screen (lateral) and a water phantom (longitudinal). The reproducibility of dose delivery between experiments was assessed by repeated measurements of the spatial dose distribution. Moreover, the reproducibility of dose-response measurements was tested by measuring the survival of irradiated HEK293 cells in three independent experiments. Results: The relative contribution of dose from nuclear reaction fragments to the sample was found to be <5% when using 90 MeV/u carbon ions. This energy still allows accurate dosimetry conforming to the IAEA Report TRS-398, facilitating comparison to dose-effect data obtained with other radiation qualities. A 1.3 mm long spread-out Bragg peak with a diameter of 30 mm was created, allowing

  7. Amorphization of diamond by ion irradiation: a Raman study

    NASA Astrophysics Data System (ADS)

    Brunetto, Rosario; Baratta, Giuseppe A.; Strazzulla, Giovanni

    2005-01-01

    We performed ion irradiation experiments on diamond samples at room temperature, probed by in-situ Raman spectroscopy. Different ions are used with energies of 200 or 400 keV. The intensity of diamond Raman band (at 1332 cm-1) decreases exponentially as the ion fluence increases. Results from different ions demonstrate that this effect is due to changes in the optical properties of the damaged samples and is correlated with the energy lost by ions through elastic collisions with target nuclei. Amorphous carbon (sp2) is formed after a threshold of about 2×1022 vacancies/cm3, or about 16 eV/C-atom deposited by elastic collisions. The peak position and full width at half maximum of the D-line and G-line of the synthesized amorphous carbon are studied. A comparison is made between the amorphization of diamond and that of graphite, forsterite, and water ice crystals. A linear relationship is found between the amorphization dose and the displacement energy. The results are discussed in view of their relevance in astrophysics.

  8. Defect recovery and damage reduction in borosilicate glasses under double ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Mir, A. H.; Peuget, S.; Toulemonde, M.; Bulot, P.; Jegou, C.; Miro, S.; Bouffard, S.

    2015-11-01

    A sodium borosilicate glass was irradiated sequentially and simultaneously with alpha particles and gold ions. Alpha particles induced partial recovery of the network damage and mechanical properties in the gold pre-irradiated glass, while no such recovery effect was observed during gold irradiation of the alpha pre-irradiated glass. The damage capacity of the gold ions was significantly reduced during simultaneous irradiation with alpha particles and gold ions. These results highlight that the irradiation sequence of the ions plays an important role in controlling the final damage level; and if properly employed, irradiation can be employed to induce defect recovery. Such results are of paramount importance to understand the radiation damage in nuclear reactor components and in nuclear waste glass matrices which are subjected to multiple particle irradiations.

  9. Systematic Ion Irradiation Experiments to Olivine: Comparison with Space Weathered Rims of Itokawa Regolith Particles

    NASA Astrophysics Data System (ADS)

    Matsumoto, T.; Tsuchiyama, A.; Watanabe, N.; Yasuda, K.; Miyake, A.; Nakauchi, Y.; Okada, T.; Abe, M.; Yada, T.; Uesugi, M.; Karouji, Y.; Nakato, A.; Hashiguschi, M.; Kumagai, K.

    2015-11-01

    We performed H and He ion irradiation experiments using olivine fragments, in order to reveal formation time-scales of space weathered rims and formation processes of blisters by solar wind irradiation.

  10. Study of irradiation damage induced by He2+ ion irradiation in Ni62Ta38 metallic glass and W metal

    NASA Astrophysics Data System (ADS)

    Zhang, Xiaonan; Mei, Xianxiu; Zhang, Qi; Li, Xiaona; Wang, Yingmin; Wang, Younian

    2017-09-01

    Metallic glasses are considered to possess good resistant against irradiation due to their inherent structural long-range disorder and a lack of grain boundaries. The He2+ with an energy of 300 keV was used to irradiate Ni62Ta38 binary metallic glass to investigate its resistance against the irradiation, and the irradiated behaviour of the metallic glass was compared with that of W metal. The irradiation fluence range over 2.0 × 1017 ions/cm2-1.6 × 1018 ions/cm2. The TEM results show that nanocrystals of μ-NiTa phase and Ni2Ta phase appeared in Ni62Ta38 metallic glass under the irradiation fluence of 1.6 × 1018 ions/cm2. The SEM results show that the surfaces of Ni62Ta38 metallic glasses maintained flat and smooth, whereas a large area of blisters with peeling formed on the surface of W metal at the irradiation fluence of 1.0 × 1018 ions/cm2. It indicates that the critical irradiation fluence of surface breakage of the Ni62Ta38 metallic glass is higher than that of W metal. After the irradiation, stress was generated in the surface layer of W metal, leading to the increase of the hardness of W metal.

  11. The influence of carbon ion irradiation on sweet sorghum seeds

    NASA Astrophysics Data System (ADS)

    Dong, X. C.; Li, W. J.; Liu, Q. F.; He, J. Y.; Yu, L. X.; Zhou, L. B.; Qu, Y.; Xie, H. M.

    2008-01-01

    The aim of this study is to investigate the effects of different doses of 100 MeV/u carbon ions on sweet sorghum seeds in order to improve crop yields and their sugar content. After irradiation, seeds were germinated and grown to 30 days, and others were sown in the field. At the end of harvesting season all planted seeds were picked separately and M2 generations obtained. The differences among the treatments were examined using the RAPD procedure. In the study done by using 38 primers; according to the amplification results, the differences among the various doses treatment were shown.

  12. Development of Nanoporous Polymer Membranes by Swift Heavy Ion Irradiation

    NASA Astrophysics Data System (ADS)

    Dinesh, Divya; Predeep, P.

    2011-10-01

    This study reveals the preparation of conical pores in polyethylene terephthalate (PET) by track etching. The polymer membrane is etched from one side by keeping between the clamps of conductivity cell followed by irradiation with swift heavy ion of 197Au. Electrical stopping supports chemical stopping. During etching process current is measured as a function of time till a sharp increase -breakthrough-observed. After etching membranes are thoroughly washed with stopping solution and water. Resultant films are characterized using Optical microscope and field emission scanning electron microscopy. Polymer films with uniform pores can be a cheaper templating material in the fields of photonic crystals and micro- electronics.

  13. Track creation after swift heavy ion irradiation of insulators

    NASA Astrophysics Data System (ADS)

    Medvedev, N.; Osmani, O.; Rethfeld, B.; Schleberger, M.

    2010-10-01

    The dynamics of structural modifications of insulators irradiated with swift heavy ions were investigated theoretically applying a combination of Monte-Carlo method (MC), used to describe SHI penetration and following excitation and relaxation of the electronic subsystem, with Two Temperature Model (TTM) describing the heating of the lattice. This MC-TTM combination demonstrates that secondary ionizations play a very important role for the track formation process. They lead to an additional term in the heat diffusion equation related to energy stored in the hole subsystem. This storage of energy causes a significant delay of heating and prolongs the timescales up to tens of picoseconds.

  14. DNA damage in mammalian cells following heavy-ion irradiation

    SciTech Connect

    Rosander, K.; Frankel, K.A.; Cerda, H.; Phillips, M.H.; Lo, E.H.; Fabrikant, I.; Fabrikant, J.I.; Levy, R.P.

    1989-09-01

    In our laboratory we have been investigating DNA damage and repair in the endothelial and oligodendroglial cells of the mouse brain after irradiation using two different types of heavy ions, helium and neon. The method used, the unwinding technique with subsequent staining of the DNA with acridine orange, has been proven to be useful for nondividing cells and analysis using a microscope photometric technique. Our primary goal has been to obtain a measure of RBE, in the dose range used in clinical treatment of various brain disorders using heavy charged particle radiosurgery. 12 refs., 5 figs.

  15. Direct observation of the primary state of damage in ion-irradiated platinum and tungsten. Report No. 4300

    SciTech Connect

    Pramanik, D

    1980-09-01

    The primary state of damage in platinum and tungsten caused by ions of varying mass and energy, was investigated using the field ion microscope (FIM). The damage could be classified into three morphological types: (a) depleted zones (DZs); (b) voids; (c) dislocation loops. Platinum specimens of 99.999% purity were irradiated in situ at 60 K with 20 keV Kr/sup +/ ions to a dose of (3 to 5) x 10/sup 12/ ion cm/sup -2/ and examined by the pulse field-evaporation technique at 60 K. The experimental conditions were created such that each depleted zone was created by a single incident ion. All three morphological types were observed.

  16. Designing self-organized nanopatterns on Si by ion irradiation and metal co-deposition.

    PubMed

    Zhang, K; Bobes, O; Hofsäss, H

    2014-02-28

    Dot and ripple nanopatterns on Si surfaces with defined symmetry and characteristic dot spacings of 50-70 nm were created by 1 keV Ar ion irradiation at normal incidence and simultaneous co-deposition of Fe atoms at grazing incidence. Fe was continuously supplied from different sputter targets surrounding the Si substrate, leading to a steady-state Fe content in the near-surface region of the substrates. The pattern formation is self-organized, most probably caused by ion-induced phase separation. Patterns were analyzed with atomic force microscopy and the Fe content in the irradiated layer was measured with Rutherford backscattering. The symmetries of the produced patterns are isotropic, four-fold symmetric, three-fold symmetric and various types of two-fold symmetric patterns, depending on the geometrical arrangement of the sputter targets. Pattern formation was studied for a steady-state coverage of Fe between 0.5 and 3.3 × 10(15) Fe cm(-2). The threshold coverage for the onset of pattern formation is about 0.5-1 × 10(15) Fe cm(-2). The coherence length of the patterns is comparable to the average dot spacing. Nevertheless, the autocorrelation analysis reveals a residual long-range periodicity of some patterns. The dot spacing can be adjusted between about 20 nm and several hundred nm depending on the ion species and ion energy.

  17. Ion-irradiation-induced hardening in Inconel 718

    NASA Astrophysics Data System (ADS)

    Hunn, J. D.; Lee, E. H.; Byun, T. S.; Mansur, L. K.

    2001-07-01

    Inconel 718 is a material under consideration for areas in the target region of the spallation neutron source (SNS), now under construction at Oak Ridge National Laboratory (ORNL) in the US. In these positions, displacement damage from protons and neutrons will affect the mechanical properties. In addition, significant amounts of helium and hydrogen will build up in the material due to transmutation reactions. Nanoindentation measurements of solution-annealed (SA) Inconel 718 specimens, implanted with Fe-, He-, and H-ions to simulate SNS target radiation conditions, have shown that hardening occurs due to ion-induced displacement damage as well as due to the build-up of helium bubbles in the irradiated layer. Precipitation-hardened (PH) Inconel 718 also exhibited hardening by helium build-up but showed softening as a function of displacement damage due to dissolution of the γ ' and γ″ precipitates.

  18. Texture coefficient analysis of ion beam irradiated copper nanowires

    NASA Astrophysics Data System (ADS)

    Rana, Pallavi; Chaudhary, Ritika; Chauhan, R. P.

    2016-05-01

    Radiation may deteriorate physical properties of the materials and leave negative as well as positive impacts especially on crystalline materials. The energy deposited by ions to the grains and grain boundaries could also influence other properties of grains like: strain, reflection of charge carriers from grain boundaries, in addition to their grain size and orientation. The intensity of a peak in the XRD spectra is the direct reflection of orientation of a miller plane in the crystal. The increased intensity symbolizes the crystalline behavior due to defects annealing, while decreased intensity portray the defects formation and slender amorphisation. Orientation distribution function is a probability distribution function that quantified the texture of a polycrystalline material. The coefficients of harmonic expansion of orientation distribution function is the measurement of the texture coefficient `TC'. This study focused on the investigation of effect of ion beam irradiation on the preffered orientation of the planes of copper nanowires.

  19. Neovascular glaucoma after helium ion irradiation for uveal melanoma

    SciTech Connect

    Kim, M.K.; Char, D.H.; Castro, J.L.; Saunders, W.M.; Chen, G.T.; Stone, R.D.

    1986-02-01

    Neovascular glaucoma developed in 22 of 169 uveal melanoma patients treated with helium ion irradiation. Most patients had large melanomas; no eyes containing small melanomas developed anterior segment neovascularization. The mean onset of glaucoma was 14.1 months (range, 7-31 months). The incidence of anterior segment neovascularization increased with radiation dosage; there was an approximately three-fold increase at 80 GyE versus 60 GyE of helium ion radiation (23% vs. 8.5%) (P less than 0.05). Neovascular glaucoma occurred more commonly in larger tumors; the incidence was not affected by tumor location, presence of subretinal fluid, nor rate of tumor regression. Fifty-three percent of patients had some response with intraocular pressures of 21 mmHg or less to a combination of antiglaucoma treatments.

  20. Activity computer program for calculating ion irradiation activation

    NASA Astrophysics Data System (ADS)

    Palmer, Ben; Connolly, Brian; Read, Mark

    2017-07-01

    A computer program, Activity, was developed to predict the activity and gamma lines of materials irradiated with an ion beam. It uses the TENDL (Koning and Rochman, 2012) [1] proton reaction cross section database, the Stopping and Range of Ions in Matter (SRIM) (Biersack et al., 2010) code, a Nuclear Data Services (NDS) radioactive decay database (Sonzogni, 2006) [2] and an ENDF gamma decay database (Herman and Chadwick, 2006) [3]. An extended version of Bateman's equation is used to calculate the activity at time t, and this equation is solved analytically, with the option to also solve by numeric inverse Laplace Transform as a failsafe. The program outputs the expected activity and gamma lines of the activated material.

  1. Texture coefficient analysis of ion beam irradiated copper nanowires

    SciTech Connect

    Rana, Pallavi Chaudhary, Ritika Chauhan, R. P.

    2016-05-23

    Radiation may deteriorate physical properties of the materials and leave negative as well as positive impacts especially on crystalline materials. The energy deposited by ions to the grains and grain boundaries could also influence other properties of grains like: strain, reflection of charge carriers from grain boundaries, in addition to their grain size and orientation. The intensity of a peak in the XRD spectra is the direct reflection of orientation of a miller plane in the crystal. The increased intensity symbolizes the crystalline behavior due to defects annealing, while decreased intensity portray the defects formation and slender amorphisation. Orientation distribution function is a probability distribution function that quantified the texture of a polycrystalline material. The coefficients of harmonic expansion of orientation distribution function is the measurement of the texture coefficient ‘TC’. This study focused on the investigation of effect of ion beam irradiation on the preffered orientation of the planes of copper nanowires.

  2. Ion irradiation induced disappearance of dislocations in a nickel-based alloy

    NASA Astrophysics Data System (ADS)

    Chen, H. C.; Li, D. H.; Lui, R. D.; Huang, H. F.; Li, J. J.; Lei, G. H.; Huang, Q.; Bao, L. M.; Yan, L.; Zhou, X. T.; Zhu, Z. Y.

    2016-06-01

    Under Xe ion irradiation, the microstructural evolution of a nickel based alloy, Hastelloy N (US N10003), was studied. The intrinsic dislocations are decorated with irradiation induced interstitial loops and/or clusters. Moreover, the intrinsic dislocations density reduces as the irradiation damage increases. The disappearance of the intrinsic dislocations is ascribed to the dislocations climb to the free surface by the absorption of interstitials under the ion irradiation. Moreover, the in situ annealing experiment reveals that the small interstitial loops and/or clusters induced by the ion irradiation are stable below 600 °C.

  3. Formation of long-range ordered quantum dots arrays in amorphous matrix by ion beam irradiation

    SciTech Connect

    Buljan, M.; Bogdanovic-Radovic, I.; Karlusic, M.; Desnica, U. V.; Radic, N.; Dubcek, P.; Drazic, G.; Salamon, K.; Bernstorff, S.; Holy, V.

    2009-08-10

    We demonstrate the production of a well ordered three-dimensional array of Ge quantum dots in amorphous silica matrix. The ordering is achieved by ion beam irradiation and annealing of a multilayer film. Structural analysis shows that quantum dots nucleate along the direction of the ion beam used for irradiation, while the mutual distance of the quantum dots is determined by the diffusion properties of the multilayer material rather than the distances between traces of ions that are used for irradiation.

  4. Magnetic force microscopy of nano-size magnetic domain ordering in heavy ion irradiated fullerene films.

    PubMed

    Kumar, Amit; Avasthi, D K; Pivin, J C; Papaléo, R M; Tripathi, A; Singh, F; Sulania, I

    2007-06-01

    In the present work, magnetic force microscopy is employed to investigate the magnetic ordering in ion irradiated fullerene films. It is observed that magnetic domain size is approximately 100-200 nm and magnetic signal is stronger at the domain boundaries. Magnetic signal arise in irradiated films is confirmed by magnetic measurements using a superconducting quantum interference device which increases with the ion fluence. The induced magnetism is possibly due to structural defects in the amorphous carbon phase formed by ion irradiation.

  5. The discrepancies in multistep damage evolution of yttria-stabilized zirconia irradiated with different ions

    SciTech Connect

    Yang, Tengfei; Taylor, Caitlin A.; Kong, Shuyan; Wang, Chenxu; Zhang, Yanwen; Huang, Xuejun; Xue, Jianming; Yan, Sha; Wang, Yugang

    2013-01-01

    This paper reports a comprehensive investigation of structural damage in yttria-stabilized zirconia irradiated with different ions over a wide fluence range. A similar multistep damage accumulation exists for the irradiations of different ions, but the critical doses for occurrence of second damage step, characterized by a faster increase in damage fraction, and the maximum elastic strain at the first damage step are varied and depend on ion mass. For irradiations of heavier ions, the second damage step occurs at a higher dose with a lower critical elastic strain. Furthermore, larger extended defects were observed in the irradiations of heavy ions at the second damage step. Associated with other experiment results and multistep damage accumulation model, the distinct discrepancies in the damage buildup under irradiations of different ions were interpreted by the effects of electronic excitation, energy of primary knock-on atom and chemistry contributions of deposited ions.

  6. Simulation of alpha decay of actinides in iron phosphate glasses by ion irradiation

    NASA Astrophysics Data System (ADS)

    Dube, Charu L.; Stennett, Martin C.; Gandy, Amy S.; Hyatt, Neil C.

    2016-03-01

    A surrogate approach of ion beam irradiation is employed to simulate alpha decay of actinides in iron phosphate nuclear waste glasses. Bismuth and helium ions of different energies have been selected for simulating glass matrix modification owing to radiolysis and ballistic damage due to recoil atoms. Structural modification and change in coordination number of network former were probed by employing Reflectance Fourier-Transform Infrared (FT-IR), and Raman spectroscopies as a consequence of ion irradiation. Depolymerisation is observed in glass sample irradiated at intermediate energy of 2 MeV. Helium blisters of micron size are seen in glass sample irradiated at low helium ion energy of 30 keV.

  7. Amorphisation of boron carbide under slow heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Gosset, D.; Miro, S.; Doriot, S.; Moncoffre, N.

    2016-08-01

    Boron carbide B4C is widely used as a neutron absorber in nuclear plants. Most of the post-irradiation examinations have shown that the structure of the material remains crystalline, in spite of very high atomic displacement rates. Here, we have irradiated B4C samples with 4 MeV Au ions with different fluences at room temperature. Transmission electron microscopy (TEM) and Raman spectroscopy have been performed. The Raman analyses show a high structural disorder at low fluence, around 10-2 displacements per atoms (dpa). However, the TEM observations show that the material remains crystalline up to a few dpa. At high fluence, small amorphous areas a few nanometers large appear in the damaged zone but the long range order is preserved. Moreover, the size and density of the amorphous zones do not significantly grow when the damage increases. On the other hand, full amorphisation is observed in the implanted zone at a Au concentration of about 0.0005. It can be inferred from those results that short range and long range damages arise at highly different fluences, that heavy ions implantation has drastic effects on the structure stability and that in this material self-healing mechanisms are active in the damaged zone.

  8. Application of ion scattering spectroscopy to measurement of surface potential of MgO thin film under ion irradiation

    SciTech Connect

    Nagatomi, T.; Kuwayama, T.; Takai, Y.; Yoshino, K.; Morita, Y.; Kitagawa, M.; Nishitani, M.

    2008-02-25

    An experimental approach was proposed for the measurement of the surface potential (SP) induced on an insulator surface during ion irradiation by ion scattering spectroscopy (ISS). The resultant ISS spectra obtained for a MgO thin film of 600 nm thickness on a Si substrate under 950 eV He{sup +} irradiation revealed that the surface is positively charged by approximately 230 V. In addition, the onset energy of a secondary ion peak indicated a SP of approximately 205 V. The present results confirmed that ISS is an effective technique for measuring the SP during ion irradiation.

  9. Microstructural evolution of nuclear grade graphite induced by ion irradiation at high temperature environment

    NASA Astrophysics Data System (ADS)

    Tsai, Shuo-Cheng; Huang, E.-Wen; Kai, Ji-Jung; Chen, Fu-Rong

    2013-03-01

    This study simulates the Wigner Effect of nuclear-grade graphite in a High Temperature Gas-cooled Reactor (HTGR). The graphite was artificially irradiated with 3 MeV C2+ ions to mimic the fast neutron-radiation damage of the HTGR core environment. The irradiation temperatures were controlled between the range of 500-800 °C in a high vacuum environment of 10-7 torr. This high-dosage radiation creates enormous amounts of Frenkel pairs, which induce lattice swelling. These Frenkel vacancies and interstitials generate new strain fields and, hence, store energy in the distorted crystalline structure. The structural integrity of nuclear grade graphite was quantified using high-resolution transmission electron microscopy (HRTEM). The microstructure was estimated by the fast Fourier transform of HRTEM images. Within the samples irradiated with 10 dpa at 600 °C, the d-spacing of {0 0 0 2} expanded from 0.336 nm to 0.396 nm accompanying with the greatest distorted graphite microstructure. The c-axis of graphite swelled approximately 18% and the disorder coefficient was 1.10 ± 0.17 (1/nm). The synchrotron X-ray experimental results, gauged from 500 μm3 volume, suggesting that the ion-implanted graphite only deformed locally and epitaxially. This study also presents possible mechanisms.

  10. Ion irradiation-induced swelling and hardening effect of Hastelloy N alloy

    NASA Astrophysics Data System (ADS)

    Zhang, S. J.; Li, D. H.; Chen, H. C.; Lei, G. H.; Huang, H. F.; Zhang, W.; Wang, C. B.; Yan, L.; Fu, D. J.; Tang, M.

    2017-06-01

    The volumetric swelling and hardening effect of irradiated Hastelloy N alloy were investigated in this paper. 7 MeV and 1 MeV Xe ions irradiations were performed at room temperature (RT) with irradiation dose ranging from 0.5 to 27 dpa. The volumetric swelling increases with increasing irradiation dose, and reaches up to 3.2% at 27 dpa. And the irradiation induced lattice expansion is also observed. The irradiation induced hardening initiates at low ion dose (≤1dpa) then saturates with higher ion dose. The irradiation induced volumetric swelling may be ascribed to excess atomic volume of defects. The irradiation induced hardening may be explained by the pinning effect where the defects can act as obstacles for the free movement of dislocation lines. And the evolution of the defects' size and number density could be responsible for the saturation of hardness.

  11. Two-dimensional MoS2 under ion irradiation: from controlled defect production to electronic structure engineering

    NASA Astrophysics Data System (ADS)

    Ghorbani-Asl, Mahdi; Kretschmer, Silvan; Spearot, Douglas E.; Krasheninnikov, Arkady V.

    2017-06-01

    Two-dimensional (2D) transition metal dichalcogenides (TMDs), like MoS2, have unique electronic and optical properties, which can further be tuned using ion bombardment and post-synthesis ion-beam mediated methods combined with exposure of the irradiated sample to precursor gases. The optimization of these techniques requires a complete understanding of the response of 2D TMDs to ion irradiation, which is affected by the reduced dimensionality of the system. By combining analytical potential molecular dynamics with first-principles calculations, we study the production of defects in free-standing MoS2 sheets under noble gas ion irradiation for a wide range of ion energies when nuclear stopping dominates, and assess the probabilities for different defects to appear. We show that depending on the incident angle, ion type and energy, sulfur atoms can be sputtered away predominantly from the top or bottom layers, creating unique opportunities for engineering mixed MoSX compounds where X are chemical elements from group V or VII. We study the electronic structure of such systems, demonstrate that they can be metals, and finally discuss how metal/semiconductor/metal junctions, which exhibit negative differential resistance, can be designed using focused ion beams combined with the exposure of the system to fluorine.

  12. Modification of Silver/Single-Wall Carbon Nanotube Electrical Contact Interfaces via Ion Irradiation.

    PubMed

    Cox, Nathanael D; Cress, Cory D; Rossi, Jamie E; Puchades, Ivan; Merrill, Andrew; Franklin, Aaron D; Landi, Brian J

    2017-03-01

    Introduction of defects via ion irradiation ex situ to modify silver/single-wall carbon nanotube (Ag-SWCNT) electrical contacts and the resulting changes in the electrical properties were studied. Two test samples were fabricated by depositing 0.1 μm Ag onto SWCNT thin films with average thicknesses of 10 and 60 nm, followed by ion irradiation (150 keV (11)B(+) at 5 × 10(14) ions/cm(2)). The contact resistance (Rc) between the Ag and SWCNT thin films was determined using transfer length method (TLM) measurements before and after ion irradiation. Rc increases for both test samples after irradiation, while there is no change in Rc for control structures with thick Ag contacts (1.5 μm), indicating that changes in Rc originate from changes in the SWCNT films and at the Ag-SWCNT interface caused by ion penetration through the Ag contact electrodes. Rc increases by ∼4× for the 60 nm SWCNT structure and increases by ∼2.4× for the 10 nm SWCNT structure. Raman spectroscopy measurements of the SWCNTs under the contacts compared to the starting SWCNT film show that the degradation of the 10 nm SWCNT structure was less significant than that of the 60 nm SWCNT structure, suggesting that the smaller change in Rc for the 10 nm SWCNT structure is a result of the thickness-dependent damage profile in the SWCNTs. Despite the increase in overall contact resistance, further TLM analysis reveals that the specific contact resistance actually decreases by ∼3.5-4× for both test samples, suggesting an enhancement of the electrical properties at the Ag-SWCNT interface. Irradiation simulations provide a physical description of the underlying mechanism, revealing that Ag atoms are forward-scattered into the SWCNTs, creating an Ag/C interfacial layer several nanometers in depth. The collective results indicate competing effects of improvement of the Ag-SWCNT interface versus degradation of the bulk SWCNT films, which has implications for scaled high-performance devices employing

  13. Surface ripple evolution by argon ion irradiation in polymers

    SciTech Connect

    Goyal, Meetika; Aggarwal, Sanjeev Sharma, Annu

    2016-03-21

    In this report, an attempt has been made to investigate the morphological evolution of nanoscale surface ripples on aliphatic (polypropylene, PP) and aromatic (polyethylene terephthalate, PET) polymeric substrates irradiated with 50 keV Ar{sup +} ions. The specimens were sputtered at off normal incidence of 30° with 5 × 10{sup 16} Ar{sup +} cm{sup −2}. The topographical features and structural behavior of the specimens were studied using Atomic Force Microscopy (AFM) and UV-Visible spectroscopy techniques, respectively. The Stopping and Range of Ions in Matter simulations were performed to calculate sputtering yield of irradiated PP and PET polymers. Sputtering yield of carbon atoms has been found to be smaller for PP (0.40) as compared to PET (0.73), which is attributed to the different structures of two polymers. AFM analysis demonstrates the evolution of ripple like features with amplitude (2.50 nm) and wavelength (690 nm) on PET while that of lower amplitude (1.50 nm) and higher wavelength (980 nm) on PP specimen. The disorder parameter (Urbach energy) has been found to increase significantly from 0.30 eV to 1.67 eV in case of PP as compared to a lesser increase from 0.35 eV to 0.72 eV in case of PET as revealed by UV-Visible characterization. A mutual correlation between ion beam sputtering induced topographical variations with that of enhancement in the disorder parameter of the specimens has been discussed.

  14. Crystallization of ultrathin W-Si multilayer structures by high-energy heavy ion irradiations

    SciTech Connect

    Marfaing, J.; Marine, W. ); Vidal, B. ); Toulemonde, M. ); Hage Ali, M.; Stoquert, J.P. )

    1990-10-22

    Ultrathin amorphous multilayers structures (1.55 nm bilayer period) were irradiated by high-energy heavy ion ({sup 127}I and {sup 238}U ions). Transmission electron microscopy study shows that the ion-material interaction in such a configuration leads to an irreversible transformation of the initial amorphous structures. In this letter, we report the first observation of the crystallization of the multilayers induced by the heavy ion irradiations with a subsequent formation of a new WSi structure. The crucial role of the electronic effects in the crystallization process is discussed relatively to the other phenomena induced under the ion irradiation.

  15. Modifications of optical properties of PC/ABS by dual ions beam irradiation

    NASA Astrophysics Data System (ADS)

    Park, Jae-Won; Lee, Jae-Sang; Lee, Byung-hoon; Kim, Min-kyu; Moon, Byung-Sik; Lee, Chan-Young; Choi, Byung-Ho

    2013-03-01

    Polycarbonate (PC)/acrylonitrile butadien styrene (ABS) blends used in the inner parts of automobiles require a glossy and metallic colored optical property. Such a surface can be produced by ion beam irradiation, but the surface treated by a single ion species irradiation tends to be degraded upon a long term exposure under UV and visible lights, which includes the loss of glossiness and the delamination of the irradiated layer. Such degradations can be prevented or greatly reduced by a combined irradiation of heavy and light ions such as N and He ions. This may be attributable to a graded interface between the irradiation affected layer and the base materials by overlapping penetration depths of the heavy and light ions. This work is motivated by an effort to substitute the conventional Cr plating process with the ion beam process in the automobile industry.

  16. Reliability studies on NPN RF power transistors under swift heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Pushpa, N.; Praveen, K. C.; Gnana Prakash, A. P.; Naik, P. S.; Cressler, John D.; Gupta, S. K.; Revannasiddaiah, D.

    2012-02-01

    NPN RF power transistors were irradiated with 140 MeV Si 10+ ions, 100 MeV F 8+ ions, 50 MeV Li 3+ ions and Co-60 gamma radiation in the dose range from 100 krad to 100 Mrad. The transistor characteristics are studied before and after irradiation from which the parameters such as Gummel characteristics, excess base current (Δ IB = IBpost - IBpre), dc current gain ( hFE), transconductance ( gm) and collector-saturation current ( ICSat) are determined. The degradation observed in the electrical characteristics is almost the same for different types of ion irradiated NPN RF power transistors with similar total doses although there is a large difference in the linear energy transfer (LET) of the ions. Further, it was observed more degradation in DC I- V characteristics of ion irradiated devices than the Co-60 gamma irradiated devices for higher doses.

  17. Mutagenic effects of carbon ion beam irradiations on dry Lotus japonicus seeds

    NASA Astrophysics Data System (ADS)

    Luo, Shanwei; Zhou, Libin; Li, Wenjian; Du, Yan; Yu, Lixia; Feng, Hui; Mu, Jinhu; Chen, Yuze

    2016-09-01

    Carbon ion beam irradiation is a powerful method for creating mutants and has been used in crop breeding more and more. To investigate the effects of carbon ion beams on Lotus japonicus, dry seeds were irradiated by 80 MeV/u carbon ion beam at dosages of 0, 100, 200, 300, 400, 500 and 600 Gy. The germination rate, survival rate and root length of M1 populations were explored and the dose of 400 Gy was selected as the median lethal dose (LD50) for a large-scale mutant screening. Among 2472 M2 plants, 127 morphological mutants including leaf, stem, flower and fruit phenotypic variation were found, and the mutation frequency was approximately 5.14%. Inter simple sequence repeat (ISSR) assays were utilized to investigate the DNA polymorphism between seven mutants and eight plants without phenotypic variation from M2 populations. No remarkable differences were detected between these two groups, and the total polymorphic rate was 0.567%.

  18. Depth profiles of fullerene in ion irradiated polyimide

    NASA Astrophysics Data System (ADS)

    Fink, D.; Klett, R.; Mathis, C.; Vacik, J.; Hnatowicz, V.; Chadderton, L. T.

    1995-05-01

    An analytical experimental technique is described which permits depth profiles of the fundamental molecule fullerene, C 60, to be determined in solids for low molecular concentrations. The method combines a procedure for the simultaneous marking and immobilizing of fullerene in organic solids, by means of lithium salt formation, with "neutron depth profiling" — a highly sensitive approach in determining specific depth distributions of 6Li. The new technique — fullerene tracer profiling (FTP) — is described in some detail, and results of the first experiments are discussed. Fullerene solutions have been introduced into both pristine and ion-irradiated samples of the polymer polyimide (PI). The C 60 depth distributions were then measured using fullerene tracer profiling. From the shapes of the depth distributions conclusions are drawn concerning the uptake of fullerene solutions by polymers and the mobility of fullerene. Fullerene does not penetrate unirradiated PI, but it does readily fill up latent tracks of energetic ions in this polymer. Depending on the specific ion track density, some 10 4 to 10 7 C 60 molecules can be identified as being present in a single track. The diffusion coefficient for C 60 is estimated to be at least 2 × 10 -12 to 2 × 10 -13 cm 2s -1, much higher than expected. This may be ascribed in part to the remarkable elastic deformability of the fullerene molecule in both kinetic and dynamic motion, and to the near perfect spherical geometry accompanying elimination of dangling bonds in simultaneously minimising the surface energy.

  19. Late degeneration in rabbit tissues after irradiation by heavy ions.

    PubMed

    Lett, J T; Cox, A B; Keng, P C; Lee, A C; Su, C M; Bergtold, D S

    1980-01-01

    In 1974, using the rabbit as a model, we began long-term experiments designed to help in the evaluation of the hazards to man from extended exposure to heavy ions in space. Such exposure would occur, for example, during the construction of solar power stations in stationary orbits or on round trips to Mars. Our experiments with 400 MeV/nucleon Ne ions and 570 MeV/nucleon Ar ions have shown that true late effects of a degenerative nature are manifested only years after irradiation. At the appropriate doses (the high end of the experimental dose range), the magnitudes of the late effects are comparable with those encountered in human patients given radiation therapy with neutrons. Such comparisons show that the rabbit experiments are applicable to man. Given that basis, the results from the low end of the experimental dose range lead to the conclusion that astronauts subjected to the radiation fluxes anticipated during flights of the above duration could experience late radiation effects one or more decades after exposure. Late degenerative changes will occur in tissues of the central nervous system, terminally differentiating systems and stem cell populations. The studies also indicate that individual tissues may be "prematurely aged" by radiation in the sense that the "life spans" of those tissues can be decreased without the appearance of malignancies.

  20. Nickel nanowires mesh fabricated by ion beam irradiation-induced nanoscale welding for transparent conducting electrodes

    NASA Astrophysics Data System (ADS)

    Honey, S.; Ahmad, I.; Madhuku, M.; Naseem, S.; Maaza, M.; Kennedy, J. V.

    2017-07-01

    In this report, random nickel nanowires (Ni-NWs) meshes are fabricated by ions beam irradiation-induced nanoscale welding of NWs on intersecting positions. Ni-NWs are exposed to beam of 50 KeV Argon (Ar+) ions at various fluencies in the range ~1015 ions cm-2 to 1016 ions cm-2 at room temperature. Ni-NWs are welded due to accumulation of Ar+ ions beam irradiation-induced sputtered atoms on crossing positions. Ar+ ions irradiated Ni-NWs meshes are optically transparent and optical transparency is enhanced with increase in beam fluence of Ar+ ions. Ar+ ions beam irradiation-induced welded and optically transparent mesh is then exposed to 2.75 MeV hydrogen (H+) ions at fluencies 1  ×  1015 ions cm-2, 3  ×  1015 ions cm-2 and 1  ×  1016 ions cm-2 at room temperature. MeV H+ ions irradiation-induced local heat cause melting and fusion of NWs on intersecting points and eventually lead to reduce contact resistance between Ni-NWs. Electrical conductivity is enhanced with increase in beam fluence of H+ ions. These welded highly transparent and electrically conductive Ni-NWs meshes can be employed as transparent conducting electrodes in optoelectronic devices.

  1. Energetic Ion and Electron Irradiation of the Icy Galilean Satellites

    NASA Technical Reports Server (NTRS)

    Cooper, John F.; Johnson, Robert E.; Mauk, Barry H.; Garrett, Henry B.; Gehrels, Neil

    2001-01-01

    Galileo Orbiter measurements of energetic ions (20 keV to 100 MeV) and electrons (20-700 keV) in Jupiter's magnetosphere are used, in conjunction with the JPL electron model (less than 40 MeV), to compute irradiation effects in the surface layers of Europa, Ganymede, and Callisto. Significant elemental modifications are produced on unshielded surfaces to approximately centimeter depths in times of less than or equal to 10(exp 6) years, whereas micrometer depths on Europa are fully processed in approximately 10 years. Most observations of surface composition are limited to optical depths of approximately 1 mm, which are indirect contact with the space environment. Incident flux modeling includes Stormer deflection by the Ganymede dipole magnetic field, likely variable over that satellite's irradiation history. Delivered energy flux of approximately 8 x 10(exp 10) keV/square cm-s at Europa is comparable to total internal heat flux in the same units from tidal and radiogenic sources, while exceeding that for solar UV energies (greater than 6 eV) relevant to ice chemistry. Particle energy fluxes to Ganymede's equator and Callisto are similar at approximately 2-3 x 10(exp 8) keV/square cm-s with 5 x 10(exp 9) at Ganymede's polar cap, the latter being comparable to radiogenic energy input. Rates of change in optical reflectance and molecular composition on Europa, and on Ganymede's polar cap, are strongly driven by energy from irradiation, even in relatively young regions. Irradiation of nonice materials can produce SO2 and CO2, detected on Callisto and Europa, and simple to complex hydrocarbons. Iogenic neutral atoms and meteoroids deliver negligible energy approximately 10(exp 4-5) keV/square cm-s but impacts of the latter are important for burial or removal of irradiation products. Downward transport of radiation produced oxidants and hydrocarbons could deliver significant chemical energy into the satellite interiors for astrobiological evolution in putative sub

  2. Energetic Ion and Electron Irradiation of the Icy Galilean Satellites

    NASA Technical Reports Server (NTRS)

    Cooper, John F.; Johnson, Robert E.; Mauk, Barry H.; Garrett, Henry B.; Gehrels, Neil

    2001-01-01

    Galileo Orbiter measurements of energetic ions (20 keV to 100 MeV) and electrons (20-700 keV) in Jupiter's magnetosphere are used, in conjunction with the JPL electron model (less than 40 MeV), to compute irradiation effects in the surface layers of Europa, Ganymede, and Callisto. Significant elemental modifications are produced on unshielded surfaces to approximately centimeter depths in times of less than or equal to 10(exp 6) years, whereas micrometer depths on Europa are fully processed in approximately 10 years. Most observations of surface composition are limited to optical depths of approximately 1 mm, which are indirect contact with the space environment. Incident flux modeling includes Stormer deflection by the Ganymede dipole magnetic field, likely variable over that satellite's irradiation history. Delivered energy flux of approximately 8 x 10(exp 10) keV/square cm-s at Europa is comparable to total internal heat flux in the same units from tidal and radiogenic sources, while exceeding that for solar UV energies (greater than 6 eV) relevant to ice chemistry. Particle energy fluxes to Ganymede's equator and Callisto are similar at approximately 2-3 x 10(exp 8) keV/square cm-s with 5 x 10(exp 9) at Ganymede's polar cap, the latter being comparable to radiogenic energy input. Rates of change in optical reflectance and molecular composition on Europa, and on Ganymede's polar cap, are strongly driven by energy from irradiation, even in relatively young regions. Irradiation of nonice materials can produce SO2 and CO2, detected on Callisto and Europa, and simple to complex hydrocarbons. Iogenic neutral atoms and meteoroids deliver negligible energy approximately 10(exp 4-5) keV/square cm-s but impacts of the latter are important for burial or removal of irradiation products. Downward transport of radiation produced oxidants and hydrocarbons could deliver significant chemical energy into the satellite interiors for astrobiological evolution in putative sub

  3. Nb2O5 Nanostructure Evolution on Nb Surfaces via Low-Energy He(+) Ion Irradiation.

    PubMed

    Novakowski, Theodore Joseph; Tripathi, Jitendra Kumar; Hassanein, Ahmed

    2016-12-21

    We propose low-energy, broad-beam He(+) ion irradiation as a novel processing technique for the generation of Nb2O5 surface nanostructures due to its relative simplicity and scalability in a commercial setting. Since there have been relatively few studies involving the interaction of high-fluence, low-energy He(+) ion irradiation and Nb (or its oxidized states), this systematic study explores both effects of fluence and sample temperature during irradiation on resulting surface morphology. Detailed normal and cross-sectional scanning electron microscopy (SEM) studies reveal subsurface He bubble formation and elucidate potential driving mechanisms for nanostructure evolution. A combination of specular optical reflectivity and X-ray photoelectron spectroscopy (XPS) is also used to gain additional information on roughness and stoichiometry of irradiated surfaces. Our investigations show significant surface modification for all tested irradiation conditions; the resulting surface structure size and geometry have a strong dependence on both sample temperature during irradiation and total ion fluence. Optical reflectivity measurements on irradiated surfaces demonstrate increased surface roughening with increasing ion fluence, and XPS shows higher oxidation levels for samples irradiated at lower temperatures, suggesting larger surface roughness and porosity. Overall, it was found that low-energy He(+) ion irradiation is an efficient processing technique for nanostructure formation, and surface structures are highly tunable by adjusting ion fluence and Nb2O5 sample temperature during irradiation. These findings may have excellent potential applications for solar energy conversion through improved efficiency due to effective light absorption.

  4. Creating The Perfect Liquid In Heavy-Ion Collisions

    SciTech Connect

    Jacak, B.; Steinberg, P.

    2010-05-01

    In 2005 the four experimental groups at Brookhaven National Laboratory's Relativistic Heavy Ion Collider (RHIC) announced that collisions of gold nuclei at ultrarelativistic energies produced a 'perfect liquid' of quarks and gluons. That's something quite different from the gaseous quark-gluon state theorists and experimenters were expecting from quantum chromodynamics, the standard theory of the strong interaction.

  5. Determination of ion track radii in amorphous matrices via formation of nano-clusters by ion-beam irradiation

    SciTech Connect

    Buljan, M.; Karlusic, M.; Bogdanovic-Radovic, I.; Jaksic, M.; Radic, N.; Salamon, K.; Bernstorff, S.

    2012-09-03

    We report on a method for the determination of ion track radii, formed in amorphous materials by ion-beam irradiation. The method is based on the addition to an amorphous matrix of a small amount of foreign atoms, which easily diffuse and form clusters when the temperature is sufficiently increased. The irradiation causes clustering of these atoms, and the final separations of the formed clusters are dependent on the parameters of the ion-beam. Comparison of the separations between the clusters that are formed by ions with different properties in the same type of material enables the determination of ion-track radii.

  6. Determination of ion track radii in amorphous matrices via formation of nano-clusters by ion-beam irradiation

    NASA Astrophysics Data System (ADS)

    Buljan, M.; Karlušić, M.; Bogdanović-Radović, I.; Jakšić, M.; Salamon, K.; Bernstorff, S.; Radić, N.

    2012-09-01

    We report on a method for the determination of ion track radii, formed in amorphous materials by ion-beam irradiation. The method is based on the addition to an amorphous matrix of a small amount of foreign atoms, which easily diffuse and form clusters when the temperature is sufficiently increased. The irradiation causes clustering of these atoms, and the final separations of the formed clusters are dependent on the parameters of the ion-beam. Comparison of the separations between the clusters that are formed by ions with different properties in the same type of material enables the determination of ion-track radii.

  7. Negative air ions created by water shearing improve erythrocyte deformability and aerobic metabolism.

    PubMed

    Iwama, H

    2004-08-01

    To elucidate a potential mechanism by which negative air ions improve aerobic metabolism, changes in venous blood lactate levels, pH, erythrocyte deformability, and plasma superoxide dismutase activity and ceruloplasmin levels were examined during a 1-h exposure to negative air ions created by water shearing or corona discharge in nine adult healthy volunteers. The blood lactate level decreased from 1.3 +/- 0.3 to 1.0 +/- 0.2 mmol/l, pH increased from 7.388 +/- 0.025 to 7.417 +/- 0.036, and erythrocyte deformability improved from 37.0 +/- 2.2 to 35.1 +/- 3.0 s, expressed as the mean +/- s.d., when exposed to negative air ions created by water shearing, but did not change when exposed to negative air ions created by corona discharge. Other variables did not change in either exposure. The results obtained suggest that negative air ions created by water shearing improve aerobic metabolism by improving erythrocyte deformability. The paper shows that negative air ions created by water shearing method improve aerobic metabolism only during a 1-h exposure, which may be caused by improvement of erythrocyte deformability, but negative air ions created by corona discharge have no effects. A potential mechanism is that negative air ions enter the circulating blood via the lungs and electrons of these ions are delivered to the plasma protein. Why negative air ions created by corona discharge have no effects is considered that water binding does not exist so that the lifetime of these ions is markedly short, by which the ions cannot reach the alveoli of the lungs sufficiently.

  8. In situ characterization of thermal conductivities of irradiated solids by using ion beam heating and infrared imaging

    NASA Astrophysics Data System (ADS)

    Mondrik, Nicholas; Gigax, Jonathan; Wang, Xuemei; Price, Lloyd; Wei, Chaochen; Shao, Lin

    2014-08-01

    We propose a method to characterize thermal properties of ion irradiated materials. This method uses an ion beam as a heating source to create a hot spot on sample surface. Infrared imaging is used as a surface temperature mapping tool to record hot zone spreading. Since ion energy, ion flux, and ion penetration depth can be precisely controlled, the beam heating data is highly reliable and repeatable. Using a high speed infrared camera to capture lateral spreading of the hot zone, thermal diffusivity can be readily extracted. The proposed method has advantages in studying radiation induced thermal property changes, for which radiation damage can be introduced by using an irradiating beam over a relatively large beam spot and beam heating can be introduced by using a focused testing beam over a relatively small beam spot. These two beams can be switched without breaking vacuum. Thus thermal conductivity changes can be characterized in situ with ion irradiation. The feasibility of the technique is demonstrated on a single crystal quartz substrate.

  9. Highly sensitive urea sensing with ion-irradiated polymer foils

    NASA Astrophysics Data System (ADS)

    Fink, Dietmar; Muñoz Hernandez, Gerardo; Alfonta, Lital

    2012-02-01

    Recently we prepared urea-sensors by attaching urease to the inner walls of etched ion tracks within thin polymer foil. Here, alternative track-based sensor configurations are examined where the enzyme remained in solution. The conductivities of systems consisting of two parallel irradiated polymer foils and confining different urea/urease mixtures in between were examined. The correlations between conductivity and urea concentration differed strongly for foils with unetched and etched tracks, which points at different sensing mechanisms - tentatively attributed to the adsorption of enzymatic reaction products on the latent track entrances and to the enhanced conductivity of reaction product-filled etched tracks, respectively. All examined systems enable in principle, urea sensing. They point at the possibility of sensor cascade construction for more sensitive or selective sensor systems.

  10. Sympathetic ophthalmia complicating helium ion irradiation of a choroidal melanoma

    SciTech Connect

    Fries, P.D.; Char, D.H.; Crawford, J.B.; Waterhouse, W.

    1987-11-01

    Sympathetic ophthalmia was diagnosed 49 months after helium ion irradiation of a left choroidal melanoma. The patient maintained good vision until 18 months after therapy, when she developed neovascular glaucoma. This complication required multiple therapeutic procedures, including topical anti-inflammatory and antiglaucomatous drops, 360 degrees peripheral panretinal cryoblation, and a single 180 degrees application of inferior cyclocryotherapy over a 2 1/2-year period. Four weeks after the cyclocryotherapy, inflammation was noted in both eyes, and, one month later, enucleation of the left sympathogenic eye was performed. Serial histopathologic sections showed a full-thickness, fibrovascular, scleral scar and tantalum marker ring suture without uveal incarceration. Penetrating surgical trauma, a uveal melanoma, and multiple nonpenetrating treatments resulted in the development of sympathetic ophthalmia.

  11. Incoherent twin boundary migration induced by ion irradiation in Cu

    NASA Astrophysics Data System (ADS)

    Li, N.; Wang, J.; Wang, Y. Q.; Serruys, Y.; Nastasi, M.; Misra, A.

    2013-01-01

    Grain boundaries can act as sinks for radiation-induced point defects. The sink capability is dependent on the atomic structures and varies with the type of point defects. Using high-resolution transmission electron microscopy, we observed that Σ3{112} incoherent twin boundary (ITB) in Cu films migrates under Cu3+ ion irradiation. Using atomistic modeling, we found that Σ3{112} ITB has the preferred sites for adsorbing interstitials and the preferential diffusion channels along the Shockley partial dislocations. Coupling with the high mobility of grain boundary Shockley dislocations within Σ3{112} ITB, we infer that Σ3{112} ITB migrates through the collective glide of grain boundary Shockley dislocations, driven by a concurrent reduction in the density of radiation-induced defects, which is demonstrated by the distribution of nearby radiation-induced defects.

  12. X-ray photoelectron spectroscopy analysis of organic materials irradiated with gas cluster ion beam

    SciTech Connect

    Nakagiri, Motohiro; Toyoda, Noriaki; Yamada, Isao

    2011-01-07

    Irradiation effect of gas cluster ion beams (GCIB) on organic materials were studied with X-ray photoelectron spectroscopy by comparison to that with Ar-monomer ions. In the case of polyimide, the intensity of both N-C = O and -C-O- bond decreased with 500 eV Ar monomer ion irradiation. On the other hand, there was no significant change in the XPS spectra after Ar-GCIB irradiation. From the size-selected GCIB irradiation study, the damages in polyimide decreased with increasing the cluster size owing to the reduction of energy per atoms.

  13. Surface pattern formation during MeV energy ion beam irradiation

    SciTech Connect

    Srivastava, S. K.; Nair, K. G. M.; Kannan, R. Kamala; Kamruddin, M.; Panigrahi, B. K.; Tyagi, A. K.

    2012-06-05

    Surface patterning during high energy heavy ion irradiation is a relatively recent observation. We report in this paper the results of a study on the formation of self organized ripple patterns on silica surface irradiated with MeV energy gold ions.

  14. Microstructural evolution of ferritic-martensitic steels under heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Topbasi, Cem

    Ferritic-martensitic steels are primary candidate materials for fuel cladding and internal applications in the Sodium Fast Reactor, as well as first-wall and blanket materials in future fusion concepts because of their favorable mechanical properties and resistance to radiation damage. Since microstructure evolution under irradiation is amongst the key issues for these materials in these applications, developing a fundamental understanding of the irradiation-induced microstructure in these alloys is crucial in modeling and designing new alloys with improved properties. The goal of this project was to investigate the evolution of microstructure of two commercial ferritic-martensitic steels, NF616 and HCM12A, under heavy ion irradiation at a broad temperature range. An in situ heavy ion irradiation technique was used to create irradiation damage in the alloy; while it was being examined in a transmission electron microscope. Electron-transparent samples of NF616 and HCM12A were irradiated in situ at the Intermediate Voltage Electron Microscope (IVEM) at Argonne National Laboratory with 1 MeV Kr ions to ˜10 dpa at temperatures ranging from 20 to 773 K. The microstructure evolution of NF616 and HCM12A was followed in situ by systematically recording micrographs and diffraction patterns as well as capturing videos during irradiation. In these irradiations, there was a period during which no changes are visible in the microstructure. After a threshold dose (˜0.1 dpa between 20 and 573 K, and ˜2.5 dpa at 673 K) black dots started to become visible under the ion beam. These black dots appeared suddenly (from one frame to the next) and are thought to be small defect clusters (2-5 nm in diameter), possibly small dislocation loops with Burgers vectors of either ½ or . The overall density of these defect clusters increased with dose and saturated around 6 dpa. At saturation, a steady-state is reached in which defects are eliminated and created at the same rates so that the

  15. Ion irradiation effects on sooting flames by-products

    NASA Astrophysics Data System (ADS)

    Brunetto, R.; Pino, T.; Dartois, E.; Cao, A. T.; D'Hendecourt, L.; Strazzulla, G.; Bréchignac, Ph.

    2008-10-01

    Carbonaceous extraterrestrial matter is observed in a wide variety of astrophysical environments. Spectroscopic signatures reveal a large variety of chemical structure illustrating the rich carbon chemistry that occurs in space. In order to produce laboratory analogues of the carbonaceous cosmic dust, a new chemical reactor has been built in the Laboratoire de Photophysique Moléculaire. It is a low pressure flat burner providing flames of premixed hydrocarbon/oxygen gas mixtures, closely following the model system used by the combustion community. In such a device the flame is a one-dimensional chemical reactor offering a broad range of combustion conditions and sampling which allows production of many and various by-products. In the present work, we have studied the effect of ion irradiation (200-400 keV), at the Laboratorio di Astrofisica Sperimentale in Catania, on several samples, ranging from strongly aromatic to strongly aliphatic materials. Infrared and Raman spectra were monitored to follow the evolution of the films under study, and characterize the irradiation process-induced modifications.

  16. MeV single-ion beam irradiation of mammalian cells using the Surrey vertical nanobeam, compared with broad proton beam and X-ray irradiations

    NASA Astrophysics Data System (ADS)

    Prakrajang, K.; Jeynes, J. C. G.; Merchant, M. J.; Kirkby, K.; Kirkby, N.; Thopan, P.; Yu, L. D.

    2013-07-01

    As a part of a systematic study on mechanisms involved in physical cancer therapies, this work investigated response of mammalian cells to ultra-low-dose ion beam irradiation. The ion beam irradiation was performed using the recently completed nanobeam facility at the Surrey Ion Beam Centre. A scanning focused vertical ion nano-beam was applied to irradiate Chinese hamster V79 cells. The V79 cells were irradiated in two different beam modes, namely, focused single ion beam and defocused scanning broad ion beam of 3.8-MeV protons. The single ion beam was capable of irradiating a single cell with a precisely controlled number of the ions to extremely low doses. After irradiation and cell incubation, the number of surviving colonies as a function of the number of the irradiating ions was measured for the cell survival fraction curve. A lower survival for the single ion beam irradiation than that of the broad beam case implied the hypersensitivity and bystander effect. The ion-beam-induced cell survival curves were compared with that from 300-kV X-ray irradiation. Theoretical studies indicated that the cell death in single ion irradiation mainly occurred in the cell cycle phases of cell division and intervals between the cell division and the DNA replication. The success in the experiment demonstrated the Surrey vertical nanobeam successfully completed.

  17. Comparison of swelling for structural materials on neutron and ion irradiation

    SciTech Connect

    Loomis, B.A.

    1986-03-01

    The swelling of V-base alloys, Type 316 stainless steel, Fe-25Ni-15Cr alloys, ferritic steels, Cu, Ni, Nb-1% Zr, and Mo on neutron irradiation is compared with the swelling for these materials on ion irradiation. The results of this comparison show that utilization of the ion-irradiation technique provides for a discriminative assessment of the potential for swelling of candidate materials for fusion reactors.

  18. Irradiation effects on secondary structure of protein induced by keV ions

    NASA Astrophysics Data System (ADS)

    Cui, F. Z.; Lin, Y. B.; Zhang, D. M.; Tian, M. B.

    2001-01-01

    Protein secondary structure changes by low-energy ion irradiation are reported for the first time. The selected system is 30 keV N + irradiation on bovine serum albumin (BSA). After irradiation at increasing fluences from 1.0×10 15 to 2.5×10 16 ion/cm 2, Fourier transform infrared spectra analysis was conducted. It was found that the secondary structures of BSA molecules were very sensitive to ion irradiation. Secondary conformations showed different trends of change during irradiation. With the increase of ion fluence from 0 to 2.5×10 16 ion/cm 2, the fraction of α-helix and β-turns decreased from 17 to 12%, and from 40 to 31%, respectively, while that of random coil and β-sheet structure increased from 18 to 27%, and from 25 to 30%, respectively. Possible explanations for the secondary conformational changes of protein are proposed.

  19. Concurrent in situ ion irradiation transmission electron microscope

    SciTech Connect

    Hattar, K.; Bufford, D. C.; Buller, D. L.

    2014-08-29

    An in situ ion irradiation transmission electron microscope has been developed and is operational at Sandia National Laboratories. This facility permits high spatial resolution, real time observation of electron transparent samples under ion irradiation, implantation, mechanical loading, corrosive environments, and combinations thereof. This includes the simultaneous implantation of low-energy gas ions (0.8–30 keV) during high-energy heavy ion irradiation (0.8–48 MeV). In addition, initial results in polycrystalline gold foils are provided to demonstrate the range of capabilities.

  20. Producing metastable nanophase with sharp interface by means of focused ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Barna, Árpád; Kotis, László; Lábár, János; Osváth, Zoltán; Tóth, Attila L.; Menyhárd, Miklós; Zalar, Anton; Panjan, Peter

    2009-02-01

    Amorphous carbon/nickel double layers were irradiated by 30 keV Ga+ ions via focused ion beam. The effect of irradiation on the concentration distribution of all constituents was studied by Auger electron spectroscopy depth profiling and cross sectional transmission electron microscopy, while the morphology change of the sample was determined by atomic force microscopy. The Ga+ ion irradiation results in the formation of metastable Ni3C layer with a uniform thickness. The C/Ni3C and Ni3C/Ni interfaces were found to be sharp up to a fluence of 200 Ga+ ions/nm2.

  1. Superlattice-like stacking fault array in ion-irradiated GaN

    SciTech Connect

    Ishimaru, Dr. Manabu; Usov, Igor Olegovich; Zhang, Yanwen; Weber, William J

    2012-01-01

    Controlling defects in crystalline solids is of technological importance for realizing desirable materials properties. Irradiation with energetic particles is useful for designing the spatial distribution and concentration of defects in materials. Here, we performed ion irradiation into hexagonal GaN with the wurtzite structure and demonstrated the spontaneous formation of superlattice-like stacking fault arrays. It was found that the modulation period can be controlled by irradiation conditions and post-irradiation heat treatments.

  2. Secondary particle tracks generated by ion beam irradiation

    NASA Astrophysics Data System (ADS)

    García, Gustavo

    2015-05-01

    The Low Energy Particle Track Simulation (LEPTS) procedure is a powerful complementary tool to include the effect of low energy electrons and positrons in medical applications of radiation. In particular, for ion-beam cancer treatments provides a detailed description of the role of the secondary electrons abundantly generated around the Bragg peak as well as the possibility of using transmuted positron emitters (C11, O15) as a complement for ion-beam dosimetry. In this study we present interaction probability data derived from IAM-SCAR corrective factors for liquid environments. Using these data, single electron and positron tracks in liquid water and pyrimidine have been simulated providing information about energy deposition as well as the number and type of interactions taking place in any selected ``nanovolume'' of the irradiated area. In collaboration with Francisco Blanco, Universidad Complutense de Madrid; Antonio Mu noz, Centro de Investigaciones Energéticas Medioambientales y Tecnológicas and Diogo Almeida, Filipe Ferreira da Silva, Paulo Lim ao-Vieira, Universidade Nova de Lisboa. Supported by the Spanish and Portuguese governments.

  3. Atomistic-Scale Simulations of Defect Formation in Graphene under Noble Gas Ion Irradiation.

    PubMed

    Yoon, Kichul; Rahnamoun, Ali; Swett, Jacob L; Iberi, Vighter; Cullen, David A; Vlassiouk, Ivan V; Belianinov, Alex; Jesse, Stephen; Sang, Xiahan; Ovchinnikova, Olga S; Rondinone, Adam J; Unocic, Raymond R; van Duin, Adri C T

    2016-09-27

    Despite the frequent use of noble gas ion irradiation of graphene, the atomistic-scale details, including the effects of dose, energy, and ion bombardment species on defect formation, and the associated dynamic processes involved in the irradiations and subsequent relaxation have not yet been thoroughly studied. Here, we simulated the irradiation of graphene with noble gas ions and the subsequent effects of annealing. Lattice defects, including nanopores, were generated after the annealing of the irradiated graphene, which was the result of structural relaxation that allowed the vacancy-type defects to coalesce into a larger defect. Larger nanopores were generated by irradiation with a series of heavier noble gas ions, due to a larger collision cross section that led to more detrimental effects in the graphene, and by a higher ion dose that increased the chance of displacing the carbon atoms from graphene. Overall trends in the evolution of defects with respect to a dose, as well as the defect characteristics, were in good agreement with experimental results. Additionally, the statistics in the defect types generated by different irradiating ions suggested that the most frequently observed defect types were Stone-Thrower-Wales (STW) defects for He(+) irradiation and monovacancy (MV) defects for all other ion irradiations.

  4. Atomistic-scale simulations of defect formation in graphene under noble gas ion irradiation

    SciTech Connect

    Yoon, Kichul; Rahnamoun, Ali; Swett, Jacob L.; Iberi, Vighter; Cullen, David A.; Vlassiouk, Ivan V.; Belianinov, Alex; Jesse, Stephen; Sang, Xiahan; Ovchinnikova, Olga S.; Rondinone, Adam Justin; Unocic, Raymond R.; van Duin, Adri C. T.

    2016-08-17

    Despite the frequent use of noble gas ion irradiation of graphene, the atomistic-scale details, including the effects of dose, energy, and ion bombardment species on defect formation, and the associated dynamic processes involved in the irradiations and subsequent relaxation have not yet been thoroughly studied. Here, we simulated the irradiation of graphene with noble gas ions and the subsequent effects of annealing. Lattice defects, including nanopores, were generated after the annealing of the irradiated graphene, which was the result of structural relaxation that allowed the vacancy-type defects to coalesce into a larger defect. Larger nanopores were generated by irradiation with a series of heavier noble gas ions, due to a larger collision cross section that led to more detrimental effects in the graphene, and by a higher ion dose that increased the chance of displacing the carbon atoms from graphene. Overall trends in the evolution of defects with respect to a dose, as well as the defect characteristics, were in good agreement with experimental results. In addition, the statistics in the defect types generated by different irradiating ions suggested that the most frequently observed defect types were Stone-Thrower-Wales (STW) defects for He+ irradiation and monovacancy (MV) defects for all other ion irradiations.

  5. Atomistic-scale simulations of defect formation in graphene under noble gas ion irradiation

    DOE PAGES

    Yoon, Kichul; Rahnamoun, Ali; Swett, Jacob L.; ...

    2016-08-17

    Despite the frequent use of noble gas ion irradiation of graphene, the atomistic-scale details, including the effects of dose, energy, and ion bombardment species on defect formation, and the associated dynamic processes involved in the irradiations and subsequent relaxation have not yet been thoroughly studied. Here, we simulated the irradiation of graphene with noble gas ions and the subsequent effects of annealing. Lattice defects, including nanopores, were generated after the annealing of the irradiated graphene, which was the result of structural relaxation that allowed the vacancy-type defects to coalesce into a larger defect. Larger nanopores were generated by irradiation withmore » a series of heavier noble gas ions, due to a larger collision cross section that led to more detrimental effects in the graphene, and by a higher ion dose that increased the chance of displacing the carbon atoms from graphene. Overall trends in the evolution of defects with respect to a dose, as well as the defect characteristics, were in good agreement with experimental results. In addition, the statistics in the defect types generated by different irradiating ions suggested that the most frequently observed defect types were Stone-Thrower-Wales (STW) defects for He+ irradiation and monovacancy (MV) defects for all other ion irradiations.« less

  6. Atomistic-scale simulations of defect formation in graphene under noble gas ion irradiation

    SciTech Connect

    Yoon, Kichul; Rahnamoun, Ali; Swett, Jacob L.; Iberi, Vighter; Cullen, David A.; Vlassiouk, Ivan V.; Belianinov, Alex; Jesse, Stephen; Sang, Xiahan; Ovchinnikova, Olga S.; Rondinone, Adam Justin; Unocic, Raymond R.; van Duin, Adri C. T.

    2016-08-17

    Despite the frequent use of noble gas ion irradiation of graphene, the atomistic-scale details, including the effects of dose, energy, and ion bombardment species on defect formation, and the associated dynamic processes involved in the irradiations and subsequent relaxation have not yet been thoroughly studied. Here, we simulated the irradiation of graphene with noble gas ions and the subsequent effects of annealing. Lattice defects, including nanopores, were generated after the annealing of the irradiated graphene, which was the result of structural relaxation that allowed the vacancy-type defects to coalesce into a larger defect. Larger nanopores were generated by irradiation with a series of heavier noble gas ions, due to a larger collision cross section that led to more detrimental effects in the graphene, and by a higher ion dose that increased the chance of displacing the carbon atoms from graphene. Overall trends in the evolution of defects with respect to a dose, as well as the defect characteristics, were in good agreement with experimental results. In addition, the statistics in the defect types generated by different irradiating ions suggested that the most frequently observed defect types were Stone-Thrower-Wales (STW) defects for He+ irradiation and monovacancy (MV) defects for all other ion irradiations.

  7. Formation of TiO{sub 2} nanorods by ion irradiation

    SciTech Connect

    Zheng, X. D.; Ren, F. Cai, G. X.; Hong, M. Q.; Xiao, X. H.; Wu, W.; Liu, Y. C.; Li, W. Q.; Ying, J. J.; Jiang, C. Z.

    2014-05-14

    Ion beam irradiation is a powerful method to fabricate and tailor the nanostructured surface of materials. Nanorods on the surface of single crystal rutile TiO{sub 2} were formed by N{sup +} ion irradiation. The dependence of nanorod morphology on ion fluence and energy was elaborated. With increasing ion fluence, nanopores grow in one direction perpendicular to the surface and burst finally to form nanorods. The length of nanorods increases with increasing ion energy under same fluence. The development of the nanorod structure is originated from the formation of the nanopores while N{sub 2} bubbles and aggregation of vacancies were responsible for the formation of nanopores and nanorods. Combining C{sup +} ion irradiation and post-irradiation annealing experiments, two qualitative models are proposed to explain the formation mechanism of these nanorods.

  8. Evaluation of irradiation hardening of ion-irradiated V-4Cr-4Ti and V-4Cr-4Ti-0.15Y alloys by nanoindentation techniques

    NASA Astrophysics Data System (ADS)

    Miyazawa, Takeshi; Nagasaka, Takuya; Kasada, Ryuta; Hishinuma, Yoshimitsu; Muroga, Takeo; Watanabe, Hideo; Yamamoto, Takuya; Nogami, Shuhei; Hatakeyama, Masahiko

    2014-12-01

    Irradiation hardening behavior of V-4Cr-4Ti and V-4Cr-4Ti-0.15Y alloys after Cu-ion beam irradiation were investigated with a combination between nanoindentation techniques and finite element method (FEM) analysis. The ion-irradiation experiments were conducted at 473 K with 2.4 MeV Cu2+ ions up to 7.6 dpa. For the unirradiated materials, the increase in nanoindentation hardness with decreasing indentation depth, so-called indentation size effect (ISE), was clearly observed. After irradiation, irradiation hardening in the measured depth was identified. Hardening behavior of bulk-equivalent hardness for V-4Cr-4Ti-0.15Y alloy was similar to that for V-4Cr-4Ti alloy. Y addition has little effect on irradiation hardening at 473 K. Adding the concept of geometrically necessary dislocations (GNDs) to constitutive equation of V-4Cr-4Ti alloy, the ISE was simulated. A constant value of α = 0.5 was derived as an optimal value to simulate nanoindentation test for ion-irradiated V-4Cr-4Ti alloy. Adding the term of irradiation hardening Δσirrad. to constitutive equation with α = 0.5, FEM analyses for irradiated surface of V-4Cr-4Ti alloy were carried out. The analytic data of FEM analyses based on neutron-irradiation hardening equivalent to 3.0 dpa agreed with the experimental data to 0.76 dpa. The comparison indicates that irradiation hardening by heavy ion-irradiation is larger than that by neutron-irradiation at the same displacement damage level. Possible mechanisms for extra hardening by heavy ion-irradiation are the processes that the injected Cu ions could effectively produce irradiation defects such as interstitials compared with neutrons, and that higher damage rate of ion-irradiation enhanced nucleation of irradiation defects and hence increased the number density of the defects compared with neutron-irradiation.

  9. Tailoring magnetism in CoNi films with perpendicular anisotropy by ion irradiation

    SciTech Connect

    Stanescu, D.; Ravelosona, D.; Mathet, V.; Chappert, C.; Samson, Y.; Beigne, C.; Gierak, J.; Bouhris, E.; Fullerton, E. E.

    2008-04-01

    This paper reports on the influence of ion irradiation on the magnetic properties of Co/Ni multilayers with perpendicular magnetic anisotropy (PMA). This material is a very promising candidate for ultrahigh density spintronic applications since it exhibits high polarization and low damping parameters. We show that PMA can be tailored in a controlled way by using uniform He{sup +} ion irradiation or focused Ga{sup +} ion beam.

  10. Band gap engineering by swift heavy ions irradiation induced amorphous nano-channels in LiNbO3

    DOE PAGES

    Sachan, Ritesh; Pakarinen, Olli H.; Liu, Peng; ...

    2015-04-01

    The irradiation of lithium niobate with swift heavy ions results in the creation of amorphous nano-sized channels along the incident ion path. These nano-channels are on the order of a hundred microns in length and could be useful for photonic applications. However, there are two major challenges in these nano-channels characterization; (i) it is difficult to investigate the structural characteristics of these nano-channels due to their very long length, and (ii) the analytical electron microscopic analysis of individual ion track is complicated due to electron beam sensitive nature of lithium niobate. Here, we report the first high resolution microscopic characterizationmore » of these amorphous nano-channels, widely known as ion-tracks, by direct imaging them at different depths in the material, and subsequently correlating the key characteristics with Se of ions. Energetic Kr ions (84Kr22 with 1.98 GeV energy) are used to irradiate single crystal lithium niobate with a fluence of 2x1010 ions/cm2, which results in the formation of individual ion tracks with a penetration depth of ~180 μm. Along the ion path, electron energy loss of the ions, which is responsible for creating the ion tracks, increases with depth under these conditions in LiNbO3, resulting in increases in track diameter of a factor of ~2 with depth. This diameter increase with electronic stopping power is consistent with predictions of the inelastic thermal spike model. We also show a new method to measure the band gap in individual ion track by using electron energy-loss spectroscopy.« less

  11. Band gap engineering by swift heavy ions irradiation induced amorphous nano-channels in LiNbO3

    SciTech Connect

    Sachan, Ritesh; Pakarinen, Olli H.; Liu, Peng; Patel, Maulik; Chisholm, Matthew F.; Zhang, Yanwen; Wang, Xuelin; Weber, William J.

    2015-04-01

    The irradiation of lithium niobate with swift heavy ions results in the creation of amorphous nano-sized channels along the incident ion path. These nano-channels are on the order of a hundred microns in length and could be useful for photonic applications. However, there are two major challenges in these nano-channels characterization; (i) it is difficult to investigate the structural characteristics of these nano-channels due to their very long length, and (ii) the analytical electron microscopic analysis of individual ion track is complicated due to electron beam sensitive nature of lithium niobate. Here, we report the first high resolution microscopic characterization of these amorphous nano-channels, widely known as ion-tracks, by direct imaging them at different depths in the material, and subsequently correlating the key characteristics with Se of ions. Energetic Kr ions (84Kr22 with 1.98 GeV energy) are used to irradiate single crystal lithium niobate with a fluence of 2x1010 ions/cm2, which results in the formation of individual ion tracks with a penetration depth of ~180 μm. Along the ion path, electron energy loss of the ions, which is responsible for creating the ion tracks, increases with depth under these conditions in LiNbO3, resulting in increases in track diameter of a factor of ~2 with depth. This diameter increase with electronic stopping power is consistent with predictions of the inelastic thermal spike model. We also show a new method to measure the band gap in individual ion track by using electron energy-loss spectroscopy.

  12. Structural damage in InGaN induced by MeV heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Zhang, L. M.; Fadanelli, R. C.; Hu, P.; Zhao, J. T.; Wang, T. S.; Zhang, C. H.

    2015-08-01

    In0.18Ga0.82N films were irradiated with 4 MeV 84Kr and 8.9 MeV 209Bi ions to various fluences at room temperature. The irradiated films were analyzed by means of Rutherford backscattering/channeling (RBS/C) and high resolution X-ray diffraction (HRXRD). The RBS/C measurements show that under the irradiation conditions, the relative lattice disorder in the films, obtained from the normalized backscattering yield, exhibits a rapid increase in the range from ∼2% to 68%. There is also an increasing lattice expansion of the films with increasing ion fluence, as determined by the HRXRD measurements. At a comparable level of lattice disorder, the Kr irradiation leads to a more pronounced lattice expansion than the Bi irradiation. This may be attributed to a larger portion of the single interstitials in the films produced by the lighter Kr ion irradiation.

  13. Role of carrier concentration in swift heavy ion irradiation induced surface modifications

    NASA Astrophysics Data System (ADS)

    Gupta, Sushant; Ganesan, V.; Sulania, Indra; Das, B.

    2017-10-01

    Highly conducting SnO2 thin films were prepared by chemical spray pyrolysis technique. One set of as-deposited films were annealed in air for 2 h at 850 °C. These as-deposited and annealed SnO2 thin films were irradiated using gold ions with energy of 120 MeV at different fluences ranging from 1 × 1011 to 3 × 1013 ions/cm2. Electrical measurement shows that as-deposited SnO2 films are in conducting state with n = 3.164 ×1020cm-3 and annealed SnO2 films are in insulating state. The amorphized latent tracks are created only above a certain threshold value of Se, which directly depends on the free electron concentration (n). The electronic energy loss (Se) of 120 MeV Au9+ ions in SnO2 is greater than the threshold energy loss (Seth) required for the latent track/molten zone formation in annealed SnO2 thin film, but is less than Seth required for as-deposited SnO2 film. Therefore, the latent tracks/molten zones are formed in the annealed SnO2 film and not in the as-deposited SnO2 film. Thermal spike model is used for the calculation of threshold energy loss and radius of melted zone. The possible mechanism of the structural changes and surface microstructure evolutions is briefly discussed in the light of ion's energy relaxation processes and target's conductivity. The atomic force microscopy (AFM) study of films shows that the morphologies of irradiated films are linked with carrier concentration of target materials.

  14. Effect of ion irradiation on the interdiffusion growth of aluminide phases in Ti Al diffusion couple

    NASA Astrophysics Data System (ADS)

    Romankov, S. E.; Mamaeva, A.; Vdovichenko, E.; Ermakov, E.

    2005-08-01

    During annealing on the Ti surface coated by the Al film, different aluminide phases were formed as the result of reactions between Ti and Al. Preliminary irradiation of the Al film with the thickness of 7 μm by Ti + ions had a strong effect on the interdiffusion growth of aluminide phases on the Ti substrate. Preliminary ion irradiation resulted in the development of more homogeneous and fine-grain microstructure during subsequent annealing. During ion irradiation of the two-phase (TiAl + Ti 3Al) overlayer the decomposition of the TiAl compound and the formation of Ti 3Al happened. In the processing of subsequent annealing, diffusion cementation of the overlayer occurred faster on the surface of the irradiated samples. After irradiation by different ions (Ti + and Al +), and during subsequent annealing the kinetics of structural formation developed in a different way.

  15. In Situ TEM Multi-Beam Ion Irradiation as a Technique for Elucidating Synergistic Radiation Effects.

    PubMed

    Taylor, Caitlin Anne; Bufford, Daniel Charles; Muntifering, Brittany Rana; Senor, David; Steckbeck, Mackenzie; Davis, Justin; Doyle, Barney; Buller, Daniel; Hattar, Khalid Mikhiel

    2017-09-29

    Materials designed for nuclear reactors undergo microstructural changes resulting from a combination of several environmental factors, including neutron irradiation damage, gas accumulation and elevated temperatures. Typical ion beam irradiation experiments designed for simulating a neutron irradiation environment involve irradiating the sample with a single ion beam and subsequent characterization of the resulting microstructure, often by transmission electron microscopy (TEM). This method does not allow for examination of microstructural effects due to simultaneous gas accumulation and displacement cascade damage, which occurs in a reactor. Sandia's in situ ion irradiation TEM (I³TEM) offers the unique ability to observe microstructural changes due to irradiation damage caused by concurrent multi-beam ion irradiation in real time. This allows for time-dependent microstructure analysis. A plethora of additional in situ stages can be coupled with these experiments, e.g., for more accurately simulating defect kinetics at elevated reactor temperatures. This work outlines experiments showing synergistic effects in Au using in situ ion irradiation with various combinations of helium, deuterium and Au ions, as well as some initial work on materials utilized in tritium-producing burnable absorber rods (TPBARs): zirconium alloys and LiAlO₂.

  16. Effects of Helium Ion Irradiation on Properties of Crystalline and Amorphous Multiphase Ceramic Coatings

    NASA Astrophysics Data System (ADS)

    Chen, Yong; Hu, Liangbin; Qiu, Changjun; He, Bin; Wang, Zhongchang

    2017-08-01

    The Al2O3-TiO2 crystalline and amorphous multiphase ceramic coatings were prepared on a martensitic steel by laser in situ reaction technique and impose irradiation with 200 keV He ions at different doses. The helium ion irradiation goes 1.55 μm deep from the surface of coating, and the displacement per atom (dpa) for the Al2O3-TiO2 coating is 20.0. When the irradiation fluency is 5 × 1017 ions/cm2, defects are identified in crystalline areas and there form interfacial areas in the coating. These crystal defects tend to migrate and converge at the interfaces. Moreover, helium ion irradiation is found to exert no effect on surface chemical composition and phase constitution of the coatings, while surface mechanical properties for the coatings after irradiation differ from those before irradiation. Further nano-indentation experiments reveal that surface nano-hardness of the Al2O3-TiO2 multiphase coatings decreases as the helium ions irradiation flux increases. Such Al2O3-TiO2 crystalline and amorphous multiphase ceramic coatings exhibit the strongest resistance against helium ion irradiation which shall be applied as candidate structural materials for accelerator-driven sub-critical system to handle the nuclear waste under extreme conditions.

  17. Effects of Helium Ion Irradiation on Properties of Crystalline and Amorphous Multiphase Ceramic Coatings

    NASA Astrophysics Data System (ADS)

    Chen, Yong; Hu, Liangbin; Qiu, Changjun; He, Bin; Wang, Zhongchang

    2017-06-01

    The Al2O3-TiO2 crystalline and amorphous multiphase ceramic coatings were prepared on a martensitic steel by laser in situ reaction technique and impose irradiation with 200 keV He ions at different doses. The helium ion irradiation goes 1.55 μm deep from the surface of coating, and the displacement per atom (dpa) for the Al2O3-TiO2 coating is 20.0. When the irradiation fluency is 5 × 1017 ions/cm2, defects are identified in crystalline areas and there form interfacial areas in the coating. These crystal defects tend to migrate and converge at the interfaces. Moreover, helium ion irradiation is found to exert no effect on surface chemical composition and phase constitution of the coatings, while surface mechanical properties for the coatings after irradiation differ from those before irradiation. Further nano-indentation experiments reveal that surface nano-hardness of the Al2O3-TiO2 multiphase coatings decreases as the helium ions irradiation flux increases. Such Al2O3-TiO2 crystalline and amorphous multiphase ceramic coatings exhibit the strongest resistance against helium ion irradiation which shall be applied as candidate structural materials for accelerator-driven sub-critical system to handle the nuclear waste under extreme conditions.

  18. Influence of high energy ion irradiation on fullerene derivative (PCBM) thin films

    NASA Astrophysics Data System (ADS)

    Sharma, Trupti; Singhal, Rahul; Vishnoi, Ritu; Lakshmi, G. B. V. S.; Biswas, S. K.

    2017-04-01

    The modifications produced by 55 MeV Si4+ swift heavy ion irradiation on the phenyl C61 butyric acid methyl ester (PCBM) thin films (thickness ∼ 100 nm) has been enlightened. The PCBM thin films were irradiated at 1 × 1010, 1 × 1011 and 1 × 1012 ions/cm2 fluences. After ion irradiation, the decreased optical band gap and FTIR band intensities were observed. The Raman spectroscopy reveals the damage produced by energetic ions. The morphological variation were investigated by atomic force microscopy and contact angle measurements and observed to be influenced by incident ion fluences. After 1011 ions/cm2 fluence, the overlapping of ion tracks starts and produced overlapping effects.

  19. First multicharged ion irradiation results from the CUEBIT facility at Clemson University

    NASA Astrophysics Data System (ADS)

    Shyam, R.; Kulkarni, D. D.; Field, D. A.; Srinadhu, E. S.; Cutshall, D. B.; Harrell, W. R.; Harriss, J. E.; Sosolik, C. E.

    2015-01-01

    A new electron beam ion trap (EBIT) based ion source and beamline were recently commissioned at Clemson University to produce decelerated beams of multi- to highly-charged ions for surface and materials physics research. This user facility is the first installation of a DREEBIT-designed superconducting trap and ion source (EBIS-SC) in the U.S. and includes custom-designed target preparation and irradiation setups. An overview of the source, beamline, and other facilities as well as results from first measurements on irradiated targets are discussed here. Results include extracted charge state distributions and first data on a series of irradiated metal-oxide-semiconductor (MOS) device targets. For the MOS devices, we show that voltage-dependent capacitance can serve as a record of the electronic component of ion stopping power for an irradiated, encapsulated oxide target.

  20. Luminescence imaging of water during carbon-ion irradiation for range estimation.

    PubMed

    Yamamoto, Seiichi; Komori, Masataka; Akagi, Takashi; Yamashita, Tomohiro; Koyama, Shuji; Morishita, Yuki; Sekihara, Eri; Toshito, Toshiyuki

    2016-05-01

    The authors previously reported successful luminescence imaging of water during proton irradiation and its application to range estimation. However, since the feasibility of this approach for carbon-ion irradiation remained unclear, the authors conducted luminescence imaging during carbon-ion irradiation and estimated the ranges. The authors placed a pure-water phantom on the patient couch of a carbon-ion therapy system and measured the luminescence images with a high-sensitivity, cooled charge-coupled device camera during carbon-ion irradiation. The authors also carried out imaging of three types of phantoms (tap-water, an acrylic block, and a plastic scintillator) and compared their intensities and distributions with those of a phantom containing pure-water. The luminescence images of pure-water phantoms during carbon-ion irradiation showed clear Bragg peaks, and the measured carbon-ion ranges from the images were almost the same as those obtained by simulation. The image of the tap-water phantom showed almost the same distribution as that of the pure-water phantom. The acrylic block phantom's luminescence image produced seven times higher luminescence and had a 13% shorter range than that of the water phantoms; the range with the acrylic phantom generally matched the calculated value. The plastic scintillator showed ∼15 000 times higher light than that of water. Luminescence imaging during carbon-ion irradiation of water is not only possible but also a promising method for range estimation in carbon-ion therapy.

  1. Surface modification and adhesion improvement of PTFE film by ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Lee, S. W.; Hong, J. W.; Wye, M. Y.; Kim, J. H.; Kang, H. J.; Lee, Y. S.

    2004-06-01

    The polytetrafluoroethylene (PTFE) surfaces, modified by 1 kV Ar + or O 2+ ion beam irradiation, was investigated with in-situ X-ray photoelectron spectroscopy (XPS), scanning electron micrographs (SEM), atomic force microscopy (AFM) measurements. The surface of PTFE films modified by Ar + ion irradiation was carbonized and the surface roughness increased with increasing ion doses. The surface of PTFE films modified by both Ar + ion in O 2 atmosphere and O 2+ ion irradiation formed the oxygen function group on PTFE surface, and the surface roughness change was relatively small. The adhesion improvement in Ar + ion irradiated PTFE surface is attributed to mechanical interlocking due to the surface roughness and CF-radical, but that in Ar + ion irradiation in an O 2 atmosphere was contributed by the CO complex and CF-radical with mechanical interlocking. The CO complex and CF-radical in O 2+ ion irradiated surface contributed to the adhesion.

  2. Long-term oxidative degradation in polyethylene irradiated with ion beams

    NASA Astrophysics Data System (ADS)

    Hama, Yoshimasa; Oka, Toshitaka; Uchiyama, Junichi; Kanbe, Hidenori; Nabeta, Kenji; Yatagai, Fumio

    2001-07-01

    The long-term oxidative degradation for high density polyethylene (HDPE) irradiated with various ion-beams was studied. Such degradation was insignificant for low density polyethylene (LDPE) even if irradiation was carried out under the same condition as for HDPE. This is attributed to a hydroperoxide group as the initiator produced by the reaction of the allyl radical with oxygen. The relationship between the mechanical properties and the local transformation induced by ion-beam irradiation was investigated. It is seen that the depth profiles of the mechanical properties along the pathway of the injected ion correspond to that of the crosslinking induced in polyethylene.

  3. EPR analysis of the effects of accelerated carbon ion and fast neutron irradiations on table sugar.

    PubMed

    Mikou, M; Benzina, S; Bischoff, P; Denis, J M; Gueulette, J

    2009-09-01

    Table sugar samples were irradiated with accelerated carbon ions and fast neutrons. Electron paramagnetic resonance (EPR) analysis performed after the irradiation revealed a complex spectrum similar to that observed after gamma-ray irradiations. The total concentration of the paramagnetic centers induced by accelerated carbon ions and neutrons was proportional to the absorbed dose. Good stability of the produced free radicals was observed for a typical period of sugar storage. Sugar was more sensitive to accelerated carbon ions than to neutrons. The results show that table sugar can be a useful material for dosimetry in the case of a radiation accident.

  4. Self-ordered defect structures in two model F/M steels under in situ ion irradiation

    NASA Astrophysics Data System (ADS)

    Kaoumi, D.; Adamson, J.

    2014-05-01

    Two model F/M steels, 9Cr-model and 12Cr-model, were irradiated with 1 MeV Kr ions in situ in a TEM at temperatures between 20 K and 573 K to doses as high as 15 dpa. During the early stages of irradiation of the two F/M steels, defect clusters were rather uniformly distributed within grains, and a saturation density was quickly reached. However, at higher doses, self-ordering alignments of defect clusters were found in some grains. The regularly ordered arrays of small loops were observed in the two F/M steels along <1 1 0> directions with spacing about 30-50 nm. Once the aligned structure was created, it was stable under further irradiation. The possible mechanisms for the “self-organization”/“ordering” of the clusters were investigated. This paper describes the process and its temperature dependence, and the possible mechanisms are discussed.

  5. Microstructural evolution in nickel alloy C-276 after Ar-ion irradiation at elevated temperature

    SciTech Connect

    Jin, Shuoxue; He, Xinfu; Li, Tiecheng; Ma, Shuli; Tang, Rui; Guo, Liping

    2012-10-15

    In present work, the irradiation damage in nickel-base alloy C-276 irradiated with Ar-ions was studied. Specimens of C-276 alloy were subjected to an irradiation of Ar-ions (with 120 keV) to dose levels of 6 and 10 dpa at 300 and 550 Degree-Sign C, respectively. The size distributions and densities of dislocation loops caused by irradiation were investigated with transmission electron microscopy. Irradiation hardening due to the formation of the loops was calculated using the dispersed barrier-hardening model, showing that irradiation hardening was greatest at 300 Degree-Sign C/6 dpa. The microstructure evolution induced by Ar-ion irradiation (0-10 dpa) in nickel-base alloy C-276 has been studied using a multi-scale modeling code Radieff constructed based on rate theory, and the size of dislocation loops simulated by Radieff was in good agreement with the experiment. - Highlights: Black-Right-Pointing-Pointer High density of dislocation loops appeared after Ar ions irradiation. Black-Right-Pointing-Pointer Irradiation hardening due to the formation of loops was calculated by the DBH model. Black-Right-Pointing-Pointer Size of loops simulated by Radieff was in good agreement with the experiment.

  6. Spectroscopic study of energetic helium-ion irradiation effects on nuclear graphite tiles

    NASA Astrophysics Data System (ADS)

    Kim, Do Wan; Lee, K. W.; Choi, D. M.; Noh, S. J.; Kim, H. S.; Lee, Cheol Eui

    2016-02-01

    Helium ion-irradiation effects on the nuclear graphite tiles were studied in order to understand the structural modifications and damages that can be produced by fusion reaction in tokamaks. The surface morphological changes due to increasing dose of the irradiation were examined by the field-effect scanning electron microscopy, and X-ray photoelectron spectroscopy elucidated the changes in the shallow surface bonding configurations caused by the energetic irradiation. Raman spectroscopy revealed the structural defects and diamond-like carbon sites that increased with increasing irradiation dose, and the average inter-defect distance was found from the Raman peak intensities as a function of the irradiation dose.

  7. Simulating the ballistic effects of ion irradiation in the binary collision approximation: A first step toward the ion mixing framework

    NASA Astrophysics Data System (ADS)

    Demange, G.; Antoshchenkova, E.; Hayoun, M.; Lunéville, L.; Simeone, D.

    2017-04-01

    Understanding ballistic effects induced by ion beam irradiation can be a key point for controlling and predicting the microstructure of irradiated materials. Meanwhile, the ion mixing framework suggests an average description of displacement cascades may be sufficient to estimate the influence of ballistic relocations on the microstructure. In this work, the BCA code MARLOWE was chosen for its ability to account for the crystal structure of irradiated materials. A first set of simulations was performed on pure copper for energies ranging from 0.5 keV to 20 keV. These simulations were validated using molecular dynamics (MD). A second set of simulations on AgCu irradiated by 1 MeV krypton ions was then carried out using MARLOWE only, as such energy is beyond reach for molecular dynamics. MARLOWE simulations are found to be in good agreement with experimental results, which suggests the predictive potential of the method.

  8. Ion irradiation induced structural modifications and increase in elastic modulus of silica based thin films

    NASA Astrophysics Data System (ADS)

    Shojaee, S. A.; Qi, Y.; Wang, Y. Q.; Mehner, A.; Lucca, D. A.

    2017-01-01

    Ion irradiation is an alternative to heat treatment for transforming organic-inorganic thin films to a ceramic state. One major shortcoming in previous studies of ion-irradiated films is the assumption that constituent phases in ion-irradiated and heat-treated films are identical and that the ion irradiation effect is limited to changes in composition. In this study, we investigate the effects of ion irradiation on both the composition and structure of constituent phases and use the results to explain the measured elastic modulus of the films. The results indicated that the microstructure of the irradiated films consisted of carbon clusters within a silica matrix. It was found that carbon was present in a non-graphitic sp2-bonded configuration. It was also observed that ion irradiation caused a decrease in the Si-O-Si bond angle of silica, similar to the effects of applied pressure. A phase transformation from tetrahedrally bonded to octahedrally bonded silica was also observed. The results indicated the incorporation of carbon within the silica network. A combination of the decrease in Si-O-Si bond angle and an increase in the carbon incorporation within the silica network was found to be responsible for the increase in the elastic modulus of the films.

  9. Ion irradiation induced structural modifications and increase in elastic modulus of silica based thin films

    PubMed Central

    Shojaee, S. A.; Qi, Y.; Wang, Y. Q.; Mehner, A.; Lucca, D. A.

    2017-01-01

    Ion irradiation is an alternative to heat treatment for transforming organic-inorganic thin films to a ceramic state. One major shortcoming in previous studies of ion-irradiated films is the assumption that constituent phases in ion-irradiated and heat-treated films are identical and that the ion irradiation effect is limited to changes in composition. In this study, we investigate the effects of ion irradiation on both the composition and structure of constituent phases and use the results to explain the measured elastic modulus of the films. The results indicated that the microstructure of the irradiated films consisted of carbon clusters within a silica matrix. It was found that carbon was present in a non-graphitic sp2-bonded configuration. It was also observed that ion irradiation caused a decrease in the Si-O-Si bond angle of silica, similar to the effects of applied pressure. A phase transformation from tetrahedrally bonded to octahedrally bonded silica was also observed. The results indicated the incorporation of carbon within the silica network. A combination of the decrease in Si-O-Si bond angle and an increase in the carbon incorporation within the silica network was found to be responsible for the increase in the elastic modulus of the films. PMID:28071696

  10. Effect of crystal orientation on hardness of He+ ion irradiated tungsten

    NASA Astrophysics Data System (ADS)

    Huang, Shilin; Ran, Guang; Lei, Penghui; Chen, Nanjun; Wu, Shenghua; Li, Ning; Shen, Qiang

    2017-09-01

    The effect of crystal orientation on hardness in the as-received, irradiated and post-irradiation annealed tungsten samples was investigated using a nanoindenter. An effective irradiation method of He+ ions with a series of energy degraded from 200 keV to 20 keV was used to continuously irradiate polycrystalline tungsten at room temperature in order to obtain a relatively homogenous displacement damage and helium concentration from sample surface to a desired depth at a NEC 400 kV ion implanter. Some irradiated samples were then annealed at 900 °C. He+ ion irradiation induced hardness increase, oppositely for the post-irradiation annealing effect. Meanwhile, the hardness of the irradiated samples was decreased sharply in the initial stage of annealing from 0 to 1 h, and then slowed down in the latter stage from 1 h to 3 h. Crystal orientation had an obvious effect on the nanoindentation hardness. The (0 0 1)-oriented grains had highest hardness at the as-received and irradiated samples. During the annealing process, the hardness in the irradiated grains with (1 1 1) crystal orientation decreased more quickly than that in the (0 0 1)-oriented grains. The mechanism of the effect of crystal orientation on hardness was analyzed and discussed.

  11. Effect of ion irradiation on the surface, structural and mechanical properties of brass

    NASA Astrophysics Data System (ADS)

    Ahmad, Shahbaz; Bashir, Shazia; Ali, Nisar; Umm-i-Kalsoom; Yousaf, Daniel; Faizan-ul-Haq; Naeem, Athar; Ahmad, Riaz; Khlaeeq-ur-Rahman, M.

    2014-04-01

    Modifications to the surface, structural and mechanical properties of brass after ion irradiation have been investigated. Brass targets were bombarded by carbon ions of 2 MeV energy from a Pelletron linear accelerator for various fluences ranging from 56 × 1012 to 26 × 1013 ions/cm2. A scanning electron microscope and X-ray diffractometer were utilized to analyze the surface morphology and crystallographic structure respectively. To explore the mechanical properties e.g., yield stress, ultimate tensile strength and microhardness of irradiated brass, an universal tensile testing machine and Vickers microhardness tester were used. Scanning electron microscopy results revealed an irregular and randomly distributed sputter morphology for a lower ion fluence. With increasing ion fluence, the incoherently shaped structures were transformed into dendritic structures. Nano/micro sized craters and voids, along with the appearance of pits, were observed at the maximum ion fluence. From X-ray diffraction results, no new phases were observed to be formed in the brass upon irradiation. However, a change in the peak intensity and higher and lower angle shifting were observed, which represents the generation of ion-induced defects and stresses. Analyses confirmed modifications in the mechanical properties of irradiated brass. The yield stress, ultimate tensile strength and hardness initially decreased and then increased with increasing ion fluence. The changes in the mechanical properties of irradiated brass are well correlated with surface and crystallographic modifications and are attributed to the generation, augmentation, recombination and annihilation of the ion-induced defects.

  12. Radiation hardness of n-type SiC Schottky barrier diodes irradiated with MeV He ion microbeam

    NASA Astrophysics Data System (ADS)

    Pastuović, Željko; Capan, Ivana; Cohen, David D.; Forneris, Jacopo; Iwamoto, Naoya; Ohshima, Takeshi; Siegele, Rainer; Hoshino, Norihiro; Tsuchida, Hidekazu

    2015-04-01

    We studied the radiation hardness of 4H-SiC Schottky barrier diodes (SBD) for the light ion detection and spectroscopy in harsh radiation environments. n-Type SBD prepared on nitrogen-doped (∼4 × 1014 cm-3) epitaxial grown 4H-SiC thin wafers have been irradiated by a raster scanning alpha particle microbeam (2 and 4 MeV He2+ ions separately) in order to create patterned damage structures at different depths within a sensitive volume of tested diodes. Deep Level Transient Spectroscopy (DLTS) analysis revealed the formation of two deep electron traps in the irradiated and not thermally treated 4H-SiC within the ion implantation range (E1 and E2). The E2 state resembles the well-known Z1/2 center, while the E1 state could not be assigned to any particular defect reported in the literature. Ion Beam Induced Charge (IBIC) microscopy with multiple He ion probe microbeams (1-6 MeV) having different penetration depths in tested partly damaged 4H-SiC SBD has been used to determine the degradation of the charge collection efficiency (CCE) over a wide fluence range of damaging alpha particle. A non-linear behavior of the CCE decrease and a significant degradation of the spectroscopic performance with increasing He ion fluence were observed above the value of 1011 cm-2.

  13. The effect of electron beam irradiation on silver-sodium ion exchange in silicate glasses

    NASA Astrophysics Data System (ADS)

    Sidorov, Alexander I.; Prosnikov, Mikhail A.

    2016-04-01

    It is shown experimentally that electron irradiation of sodium-silicate glasses makes possible the control of the subsequent ion exchange Ag+ ↔ Na+ process in a salt melt. The reason of this effect is the negatively charged regions formation in a glass volume during electron irradiation. The electric field, produced by these regions in glass volume, results in positive Na+ ions field migration into them. The spatial redistribution of Na+ ions results in the decrease of the ion exchange efficiency, or the ion exchange can be even blocked. This led to the decrease of the luminescence intensity of neutral silver molecular clusters in the irradiated zone, and effect on the silver nanoparticles formation during the subsequent thermal treatment. The observed effects can be used for the control of ion exchange processes during integrated optics devices fabrication, and for the electron-beam recording of optical information.

  14. Effect of gigaelectron volt Au-ion irradiation on the characteristics of ultrananocrystalline diamond films

    SciTech Connect

    Chen, Huang-Chin; Teng, Kuang-Yau; Tang, Chen-Yau; Lin, I-Nan; Sundaravel, Balakrishnan; Amirthapandian, Sankarakumar

    2010-12-15

    The effect of 2.245 GeV Au-ion irradiation/postannealing processes on the electron field emission (EFE) properties of ultrananocrystalline diamond (UNCD) films was investigated. Au-ion irradiation with a fluence of around 8.4x10{sup 13} ions/cm{sup 2} is required to induce a large improvement in the EFE properties of the UNCD films. Postannealing the Au-ion irradiated films at 1000 deg. C for 1 h slightly degraded the EFE properties of the films but the resulting EFE behavior was still markedly superior to that of pristine UNCD films. Transmission electron microscopy examinations revealed that the EFE properties of the UNCD films are primarily improved by Au-ion irradiation/postannealing processes because of the formation of nanographites along the trajectory of the irradiating ions, which results in an interconnected path for electron transport. In contrast, the induction of grain growth process due to Au-ion irradiation in UNCD films is presumed to insignificantly degrade the EFE properties for the films as the aggregates are scarcely distributed and do not block the electron conducting path.

  15. Low energy helium ion irradiation induced nanostructure formation on tungsten surface

    NASA Astrophysics Data System (ADS)

    Al-Ajlony, A.; Tripathi, J. K.; Hassanein, A.

    2017-05-01

    We report on the low energy helium ion irradiation induced surface morphology changes on tungsten (W) surfaces under extreme conditions. Surface morphology changes on W surfaces were monitored as a function of helium ion energy (140-300 eV), fluence (2.3 × 1024-1.6 × 1025 ions m-2), and flux (2.0 × 1020-5.5 × 1020 ion m-2 s-1). All the experiments were performed at 900° C. Our study shows significant effect of all the three ion irradiation parameters (ion flux, fluence, and energy) on the surface morphology. However, the effect of ion flux is more pronounced. Variation of helium ion fluence allows to capture the very early stages of fuzz growth. The observed fuzz growth and morphology changes were understood in the realm of various possible phenomena. The study has relevance and important impact in the current and future nuclear fusion applications.

  16. The influence of fractionation on cell survival and premature differentiation after carbon ion irradiation.

    PubMed

    Wang, Jufang; Li, Renming; Guo, Chuanling; Fournier, Claudia; K-Weyrather, Wilma

    2008-07-01

    To investigate the influence of fractionation on cell survival and radiation induced premature differentiation as markers for early and late effects after X-rays and carbon irradiation. Normal human fibroblasts NHDF, AG1522B and WI-38 were irradiated with 250 kV X-rays, or 266 MeV/u, 195 MeV/u and 11 MeV/u carbon ions. Cytotoxicity was measured by a clonogenic survival assay or by determination of the differentiation pattern. Experiments with high-energy carbon ions show that fractionation induced repair effects are similar to photon irradiation. The RBE(10) values for clonogenic survival are 1.3 and 1.6 for irradiation in one or two fractions for NHDF cells and around 1.2 for AG1522B cells regardless of the fractionation scheme. The RBE for a doubling of post mitotic fibroblasts (PMF) in the population is 1 for both single and two fractionated irradiation of NHDF cells. Using 11 MeV/u carbon ions, no repair effect can be seen in WI-38 cells. The RBE(10) for clonogenic survival is 3.2 for single irradiation and 4.9 for two fractionated irradiations. The RBE for a doubling of PMF is 3.1 and 5.0 for single and two fractionated irradiations, respectively. For both cell lines the effects of high-energy carbon ions representing the irradiation of the skin and the normal tissue in the entrance channel are similar to the effects of X-rays. The fractionation effects are maintained. For the lower energy, which is representative for the irradiation of the tumor region, RBE is enhanced for clonogenic survival as well as for premature terminal differentiation. Fractionation effects are not detectable. Consequently, the therapeutic ratio is significantly enhanced by fractionated irradiation with carbon ions.

  17. Effect of Swift Heavy Ion Irradiation on Lithium Zinc Silicate Glasses: A Photoluminescence Study

    NASA Astrophysics Data System (ADS)

    Jogad, M. S.; Jogad, R. M.; Sudarsan, V.; Krishna, P. S. R.; Kothiyal, G. P.

    2011-07-01

    Lithium zinc silicate glasses with and without copper were prepared by melt-quench method and their luminescence characteristics after swift heavy ion irradiation has been investigated. Based on these studies it is established that both these glasses contain colour centres and the luminescence from such centres get significantly quenched once these samples get irradiated with 100 MeV swift heavy Ag+ ions with a fluence of 1013ions/cm2 at room temperature. Trapping of the charge carriers by the increased defect concentration brought about by irradiation is responsible for the decrease in the luminescence intensity from the irradiated samples. Copper in these glasses mainly exists as Cu+ ions as revealed by the broad emission around 500 nm.

  18. Molecular alteration and carbonization of aspartic acid upon N + ion irradiation

    NASA Astrophysics Data System (ADS)

    Cui, F. Z.; Sun, S. Q.; Zhang, D. M.; Ma, Z. L.; Chen, G. Q.

    2000-06-01

    Structural changes of aspartic acid (Asp) irradiated by nitrogen ions of 30 keV were studied using Fourier transform infrared (FTIR) spectroscopy. Significant decreases of the intensities of COO -, NH 3+, COOH and CH 2 vibrations in the FTIR spectra, compared with those of unirradiated Asp, were observed for the sample irradiated at the fluence of 1×10 16 ions/cm 2. The decrease rates of the intensities of COO -, NH 3+, COOH and CH 2 vibrations with respect to the increasing irradiation fluences up to 4×10 16 ions/cm 2 were different. The results were attributable to the nonstoichiometrical desorption of corresponding volatile species such as H 2, NH 3+ and CO 2. The radiolysis residue of Asp after irradiation at a high fluence of 1×10 17 ions/cm 2 was analyzed and fatty acid was detected.

  19. Investigation of Current Spike Phenomena During Heavy Ion Irradiation of NAND Flash Memories

    NASA Technical Reports Server (NTRS)

    Oldham, Timothy R.; Berg, Melanie; Friendlich, Mark; Wilcox, Ted; Seidleck, Christina; LaBel, Kenneth A.; Irom, Farokh; Buchner, Steven P.; McMorrow, Dale; Mavis, David G.; hide

    2011-01-01

    A series of heavy ion and laser irradiations were performed to investigate previously reported current spikes in flash memories. High current events were observed, however, none matches the previously reported spikes. Plausible mechanisms are discussed.

  20. Nano-porosity in GaSb induced by swift heavy ion irradiation

    SciTech Connect

    Kluth, P. Schnohr, C. S.; Giulian, R.; Araujo, L. L.; Lei, W.; Rodriguez, M. D.; Afra, B.; Bierschenk, T.; Ridgway, M. C.; Sullivan, J.; Weed, R.; Li, W.; Ewing, R. C.

    2014-01-13

    Nano-porous structures form in GaSb after ion irradiation with 185 MeV Au ions. The porous layer formation is governed by the dominant electronic energy loss at this energy regime. The porous layer morphology differs significantly from that previously reported for low-energy, ion-irradiated GaSb. Prior to the onset of porosity, positron annihilation lifetime spectroscopy indicates the formation of small vacancy clusters in single ion impacts, while transmission electron microscopy reveals fragmentation of the GaSb into nanocrystallites embedded in an amorphous matrix. Following this fragmentation process, macroscopic porosity forms, presumably within the amorphous phase.

  1. Effect of 100MeV oxygen ion irradiation on silicon NPN power transistor

    SciTech Connect

    Kumar, M. Vinay; Krishnakumar, K. S.; Dinesh, C. M.; Krishnaveni, S.; Ramani

    2012-06-05

    The radiation response of npn Bipolar junction transistor (BJT) has been examined for 100 MeV O{sup 7+} ion. Key electrical properties like Gummel characteristics, dc current gain and capacitance-voltage of 100MeV O{sup 7+} ion irradiated transistor were studied before and after irradiation. The device was decapped and the electrical characterizations were performed at room temperature. Base current is observed to be more sensitive than collector current and gain appears to be degraded with ion fluence, also considerable degradation in C-V characteristics is observed and doping concentration is found to be increased along with the increase in ion fluence.

  2. Effect of 100MeV oxygen ion irradiation on silicon NPN power transistor

    NASA Astrophysics Data System (ADS)

    Kumar, M. Vinay; Krishnakumar, K. S.; Dinesh, C. M.; Krishnaveni, S.; Ramani

    2012-06-01

    The radiation response of npn Bipolar junction transistor (BJT) has been examined for 100 MeV O7+ ion. Key electrical properties like Gummel characteristics, dc current gain and capacitance-voltage of 100MeV O7+ ion irradiated transistor were studied before and after irradiation. The device was decapped and the electrical characterizations were performed at room temperature. Base current is observed to be more sensitive than collector current and gain appears to be degraded with ion fluence, also considerable degradation in C-V characteristics is observed and doping concentration is found to be increased along with the increase in ion fluence.

  3. Superlattice-Like Stacking Fault Array in Ion-Irradiated GaN

    SciTech Connect

    Ishimaru, Manabu; Usov, Igor O.; Zhang, Yanwen; Weber, William J.

    2012-01-01

    Controlling defects in crystalline solids is of technological importance for realizing desirable material properties. Irradiation with energetic particles is useful for designing the spatial distribution and concentration of defects in materials. Here, we performed ion irradiation into hexagonal GaN with the wurtzite structure and demonstrated the spontaneous formation of superlattice-like stacking fault arrays. It was found that the modulation period can be controlled by varying the irradiation conditions and subsequent thermal treatments.

  4. Effect of defect imbalance on void swelling distributions produced in pure iron irradiated with 3.5 MeV self-ions

    SciTech Connect

    Shao, Lin; Wei, C. -C.; Gigax, J.; Aitkaliyeva, A.; Chen, D.; Sencer, B. H.; Garner, F. A.

    2014-06-10

    Ion irradiation has been widely used to simulate radiation damage induced by neutrons. However, there are a number of features of ion-induced damage that differ from neutron-induced damage, and these differences require investigation before behavior arising from neutron bombardment can be confidently predicted from ion data. In this study 3.5 MeV self-ion irradiation of pure iron was used to study the influence on void swelling of the depth-dependent defect imbalance between vacancies and interstitials that arises from various surface effects, forward scattering of displaced atoms, and especially the injected interstitial effect. The depth dependence of void swelling was observed not to follow the behavior anticipated from the depth dependence of the damage rate. Void nucleation and growth develop first in the lower-dose, near-surface region, and then, during continued irradiation, move to progressively deeper and higher-damage depths. This indicates a strong initial suppression of void nucleation in the peak damage region that continued irradiation eventually overcomes. This phenomenon is shown by the Boltzmann transport equation method to be due to depth-dependent defect imbalances created under ion irradiation. These findings thus demonstrate that void swelling does not depend solely on the local dose level and that this sensitivity of swelling to depth must be considered in extracting and interpreting ion-induced swelling data.

  5. Effect of defect imbalance on void swelling distributions produced in pure iron irradiated with 3.5 MeV self-ions

    DOE PAGES

    Shao, Lin; Wei, C. -C.; Gigax, J.; ...

    2014-06-10

    Ion irradiation has been widely used to simulate radiation damage induced by neutrons. However, there are a number of features of ion-induced damage that differ from neutron-induced damage, and these differences require investigation before behavior arising from neutron bombardment can be confidently predicted from ion data. In this study 3.5 MeV self-ion irradiation of pure iron was used to study the influence on void swelling of the depth-dependent defect imbalance between vacancies and interstitials that arises from various surface effects, forward scattering of displaced atoms, and especially the injected interstitial effect. The depth dependence of void swelling was observed notmore » to follow the behavior anticipated from the depth dependence of the damage rate. Void nucleation and growth develop first in the lower-dose, near-surface region, and then, during continued irradiation, move to progressively deeper and higher-damage depths. This indicates a strong initial suppression of void nucleation in the peak damage region that continued irradiation eventually overcomes. This phenomenon is shown by the Boltzmann transport equation method to be due to depth-dependent defect imbalances created under ion irradiation. These findings thus demonstrate that void swelling does not depend solely on the local dose level and that this sensitivity of swelling to depth must be considered in extracting and interpreting ion-induced swelling data.« less

  6. Magnetic patterning of Fe/Cr/Fe(001) trilayers by Ga{sup +} ion irradiation

    SciTech Connect

    Blomeier, S.; Hillebrands, B.; Demidov, V.E.; Demokritov, S.O.; Reuscher, B.; Brodyanski, A.; Kopnarski, M.

    2005-11-01

    Magnetic patterning of antiferromagnetically coupled epitaxial Fe (10 nm)/Cr (0.7 nm)/Fe (10 nm) (001) trilayers by irradiation with 30 keV Ga{sup +} ions was studied by means of atomic force microscopy, magnetic force microscopy, and Kerr magnetometry. It was found that within a fluence range of (1.25-5)x10{sup 16} ions/cm{sup 2} a complete transition from antiferromagnetic to ferromagnetic coupling between the two Fe layers can be achieved. The magnetization reversal processes of the nonirradiated, antiferromagnetically coupled areas situated close to the irradiated areas were studied with lateral resolution. Evidence for a lateral coupling mechanism between the magnetic moments of the irradiated and nonirradiated areas was found. Special attention was paid to preserve the flatness of the irradiated samples. Depending on the fluence, topographic steps ranging from +1.5 to -2 nm between the nonirradiated and irradiated areas were observed. At lower fluences the irradiation causes an increase of the surface height, while for higher fluences the height decreases. It was found that for the particular fluence of 2.7x10{sup 16} ions/cm{sup 2} no height difference between the irradiated and nonirradiated areas occurs. The results suggest that the irradiation of Fe/Cr/Fe trilayers with midenergy ions is an innovative method for magnetic patterning, preserving the initial smoothness of the sample.

  7. Thermal annealing of vacancy and interstitial loops in ion irradiated copper

    SciTech Connect

    Larson, B.C.; Noggle, T.S.; Barhorst, J.F.

    1985-01-01

    X-ray diffuse scattering has been used to study the thermal annealing of vacancy and interstitial loops in Ni-ion irradiated copper. The diffuse scattering formalism is reviewed and diffuse scattering measurements are reported on liquid-He temperature Ni-ion irradiated copper after annealing to 40, 275, and 300/sup 0/C. Size distributions are presented for vacancy and interstitial loops after each anneal and the thermal-induced changes are discussed in terms of loop dissolution and coalescence.

  8. Fabrication of a TEM sample of ion-irradiated material using focused ion beam microprocessing and low-energy Ar ion milling.

    PubMed

    Jin, Hyung-Ha; Shin, Chansun; Kwon, Junhyun

    2010-01-01

    Cross-section-view TEM samples of ion-irradiated material are successfully fabricated using a focused ion beam (FIB) system and low-energy Ar ion milling. Ga ion-induced damages in FIB processing are reduced remarkably by the means of low-energy Ar ion milling. There are optimized ion milling conditions for the reduction and removal of the secondary artifacts such as defects and ripples. Incident angles and accelerated voltages are especially more important factors on the preservation of a clean surface far from secondary defects and surface roughing due to Ga and Ar ion bombardment.

  9. Positron annihilation Doppler broadening spectroscopy study on Fe-ion irradiated NHS steel

    NASA Astrophysics Data System (ADS)

    Zhu, Huiping; Wang, Zhiguang; Gao, Xing; Cui, Minghuan; Li, Bingsheng; Sun, Jianrong; Yao, Cunfeng; Wei, Kongfang; Shen, Tielong; Pang, Lilong; Zhu, Yabin; Li, Yuanfei; Wang, Ji; Song, Peng; Zhang, Peng; Cao, Xingzhong

    2015-02-01

    In order to study the evolution of irradiation-induced vacancy-type defects at different irradiation fluences and temperatures, a new type of ferritic/martensitic (F/M) steel named NHS (Novel High Silicon) was irradiated by 3.25 MeV Fe-ion at room temperature and 723 K to fluences of 4.3 × 1015 and 1.7 × 1016 ions/cm2. After irradiation, vacancy-type defects were investigated with variable-energy positron beam Doppler broadening spectra. Energetic Fe-ions produced a large number of vacancy-type defects in the NHS steel, but one single main type of vacancy-type defect was observed in both unirradiated and irradiated samples. The concentration of vacancy-type defects decreased with increasing temperature. With the increase of irradiation fluence, the concentration of vacancy-type defects increased in the sample irradiated at RT, whereas for the sample irradiated at 723 K, it decreased. The enhanced recombination between vacancies and excess interstitial Fe atoms from deeper layers, and high diffusion rate of self-interstitial atoms further improved by diffusion via grain boundary and dislocations at high temperature, are thought to be the main reasons for the reversed trend of vacancy-type defects between the samples irradiated at RT and 723 K.

  10. SU-C-204-04: Irradiation of Human Cell Lines Using Various Ions

    SciTech Connect

    Lin, Y; McMahon, S; Kaminuma, T; Held, K; Tessa, C; Rusek, A

    2016-06-15

    Purpose: The purpose of this study is to investigate and quantify the biological effects of ion radiation using several human cell lines. We aim to answer the question of whether carbon ion the most ideal ion species for heavy ion radiotherapy. Methods: The cells were irradiated at different positions along the pristine Bragg peak of several ions with different atomic number. The biological effectiveness was evaluated using the clonogenic cell survival assay. Irradiation of three human lung cancer cell lines and a fibroblast cell line were undertaken using the charged particle beam at the NASA Space Radiation Laboratory at Brookhaven National Lab. Four mono-energetic ion beams (carbon, oxygen, helium and lithium) were used to irradiate the cells. Water or media-filled T25 flasks were lined up along the beam line so that the cell-containing surfaces of the flasks were placed at a specific depth along the pristine Bragg curve. Four depths along the curve, representing entrance point, rising peak, peak and distal fall off, were selected to determine biological effectiveness. Gaf-chromic films were placed between the flasks to monitor the irradiation as soon as it was finished. Results: For all ion radiations, the maximum cell killing effect occurs at either peak or distal fall off, depending on the cell lines. For instance, for the fibroblast cell line AGO1522, RBEs of 1.4, 1.2, 1.4 and 1.9 were observed at the Bragg peak for Helium, Lithium, Carbon and Oxygen ions. Comparing positions, RBEs of 0.9, 1.2, 1.4 and 1.8 were observed for carbon irradiation of AGO-1522 cells positions corresponding to entrance, rising peak, peak and distal fall off. Conclusion: RBE values differ with position in the Bragg peak, ion species and cell line. Ions other than carbon may prove more effective in certain irradiation conditions and may contribute to optimized heavy ion therapy.

  11. Electrical properties of irradiated PVA film by using ion/electron beam

    NASA Astrophysics Data System (ADS)

    Abdelrahman, M. M.; Osman, M.; Hashhash, A.

    2016-02-01

    Ion/electron beam bombardment has shown great potential for improving the surface properties of polymers. Low-energy charged (ion/electron) beam irradiation of polymers is a good technique to modify properties such as electrical conductivity, structural behavior, and their mechanical properties. This paper reports on the effect of nitrogen and electron beam irradiation on the electrical properties of polyvinyl alcohol (PVA) films. PVA films of 4 mm were exposed to a charged (ion/electron) beam for different treatment times (15, 30, and 60 minutes); the beam was produced from a dual beam source using nitrogen gas with the other ion/electron source parameters optimized. The dielectric loss tangent tan δ , electrical conductivity σ , and dielectric constant ɛ ^' } in the frequency range 100 Hz-100 kHz were measured at room temperature. The variation of dielectric constant and loss tangent as a function of frequency was also studied at room temperature. The dielectric constant was found to be strongly dependent on frequency for both ion and electron beam irradiation doses. The real (ɛ ^' }) and imaginary (ɛ ^' ' }) parts of the dielectric constant decreased with frequency for all irradiated and non-irradiated samples. The AC conductivity showed an increase with frequency for all samples under the influence of both ion and electron irradiation for different times. Photoluminescence (PL) spectral changes were also studied. The formation of clusters and defects (which serve as non-radiative centers on the polymer surface) is confirmed by the decrease in the PL intensity.

  12. Ion-irradiation of complex hydrocarbons: implications for small Solar System bodies

    NASA Astrophysics Data System (ADS)

    Moroz, L.; Baratta, G.; Distefano, E.; Strazzulla, G.; Dotto, E.; Barucci, M.; Arnold, G.

    2003-04-01

    Trans-Neptunian Objects (TNOs) and cometary nuclei show remarkable color variations. In the visual and near-infrared spectral regions their colors may range from red to gray or bluish. This probably indicates that surface alteration processes such as space weathering and impact resurfacing plays an essential role in the color diversity of such bodies. In particular, some previous laboratory ion-irradiation experiments demonstrated a transformation of surface colors of ices from gray to red and further to gray. Additional possibility is a transformation of originally red dark refractory organic surface components into a gray carbonized material as a result of ion irradiation. We simulated such an "ageing" effect by an irradiation of a natural dark red organic samples (asphaltite and kerite). The samples were irradiated by 30-60 keV H+, N+ and Ar++ ions and their reflectance spectra were measured before and after irradiation. The results indicate that initially red spectra of organics progressively flatten with increasing ion fluences. The laboratory spectra have been compared with astronomical spectra of TNOs. We demonstrate that an observed variety of TNO’ spectral slopes can be reproduced by our laboratory spectra corresponding to different ion fluences. If we assume that fresh surfaces of some TNOs are red due to their refractory organic components, then their irradiation by ion populations in the Solar System in combination with collisional evolution exposing these fresh surfaces could have produced a variety of colors.

  13. Evolutions of Molecular Oxygen Formation and Sodium Migration in Xe Ion Irradiated Borosilicate Glasses

    SciTech Connect

    Chen, Liang; Zhang, Duofei F.; Lv, Peng; Zhang, Jiandong; Du, Xing; Yuan, Wei; Nan, Shuai; Zhu, Zihua; Wang, Tieshan

    2016-07-23

    The modifications of a commercial borosilicate glass induced by Xe ion irradiation have been studied by Raman spectroscopy and ToF-SIMS depth profiling. A decrease in the average Si–O–Si angle, an increase in the population of three-membered rings and an increase of the glass polymerization are evidenced. The molecular oxygen appears in the irradiated glasses after the irradiation fluence reaches approximately 1015 ions/cm2. The O2 concentration decreaseswith the depth of irradiated glass at the ion fluence of 2 × 1016 ions/cm2. A sodiumdepleted layer at the surface and a depleted zone at around the penetration depth of 5 MeV Xe ions are observed. The thickness of the sodium depleted layer increases with the irradiation fluence. Moreover, comparing with previous results after electron and Ar ion irradiation, it can be concluded that the nuclear energy deposition can partially inhibit the formation of molecular oxygen and increase the threshold value of electron energy deposition for the molecular oxygen formation.

  14. Ion irradiation induced evolution of nanostructure in a graded multi-trilayer system

    NASA Astrophysics Data System (ADS)

    Roy, Sumalay; Ghatak, J.; Dev, B. N.

    2012-02-01

    Nanostructural modifications in a double-graded Pt/Ni/C multi-trilayer, due to irradiation by an energetic ion-beam, have been analyzed using X-ray reflectivity (XRR), X-ray standing wave (XSW) and cross-sectional transmission electron microscopy (X-TEM) techniques. 2 MeV Au2+ ions were rastered on Pt/Ni/C multi-trilayer samples producing a uniformly irradiated area at ion-fluences ranging from 1 × 1014 ions/cm2 to 2 × 1015 ions/cm2. Ion irradiation induced modifications of microstructural parameters, e.g., layer thicknesses and electron densities of individual layers and interface roughnesses have been obtained from XRR analysis. Pt- and Ni-fluorescence yield from the as-deposited sample under the XSW condition show the distinct existence of Pt and Ni layers. The almost indistinguishable Pt- and Ni-fluorescence data over the first order Bragg peak from the sample irradiated at the highest ion-fluence, suggest complete mixing of Pt and Ni. Strong mixing between Pt and Ni in the ion irradiated samples is also corroborated by XRR results. X-TEM studies reveal the individual layer structure in the as-deposited sample. This layer structure is lost in the sample irradiated at the highest ion fluence indicating a complete mixing between Pt and Ni layers and nanoscale grain growth of Pt-Ni alloys. Additionally, formation of Pt-Ni alloy nano-clusters in the C-layers is observed. The results are understood in the light of the positive heat of mixing between Pt and C, and Ni and C and the negative heat of mixing between Pt and Ni. The effect of heat of mixing becomes dominant at high fluence irradiation.

  15. A diffraction grating created in diamond substrate by boron ion implantation

    NASA Astrophysics Data System (ADS)

    Stepanov, A. L.; Nuzhdin, V. I.; Galyautdinov, M. F.; Kurbatova, N. V.; Valeev, V. F.; Vorobev, V. V.; Osin, Yu. N.

    2017-01-01

    This work is devoted to new method of manufacturing of diffractive optical elements (gratings). A grating was formed in a diamond substrate by implantation with boron ions through a mask. Ion implantation led to the graphitization of diamond in unmasked regions and resulted in swelling of the irradiated layer. The formation of periodic graphitized surface microstructures on the diamond substrate was confirmed by optical, electron, and atomic force microscopy. The efficiency of operation of the obtained diffractive optical element was demonstrated by probing with He-Ne laser radiation.

  16. Micro-Raman spectroscopy characterization of silicon with different structures irradiated with energetic Bi-ions

    NASA Astrophysics Data System (ADS)

    Zhu, Yabin; Yao, Cunfeng; Wang, Ji; Zhu, Huiping; Shen, Tielong; Gao, Xing; Sun, Jianrong; Wei, Kongfang; Wang, Dong; Sheng, Yanbin; Wang, Zhiguang

    2015-12-01

    Researches of irradiation effects on silicon possess not only fundamental interests but also potential application prospects. Comparison studies about structural modification of silicon materials with different structures under identical irradiation conditions can reveal the irradiation mechanisms for amorphous and crystalline phases of silicon. For this purpose, amorphous silicon (a-Si) and nano-crystalline silicon (nc-Si) films as well as mono-crystalline silicon (c-Si) samples were irradiated with 6.0 MeV Bi-ions at room temperature. The ion fluences are 1.0 × 1013, 5.0 × 1013 and 1.0 × 1014 ions/cm2. All samples were analyzed by using a Raman spectrometer. The obtained results show that the crystalline fraction of c-Si and nc-Si decrease with increasing fluence, which indicates that the irradiation induces the amorphization of nc-Si and c-Si samples. In addition, the variation in Raman frequency of crystalline peak after irradiation reveals that the irradiation also results in the increased stress in crystalline phase of c-Si and nc-Si samples. As the fluence increases, the bond angle deviation and the ratio of TA to TO mode of amorphous network of a-Si and nc-Si films initially increase and then decrease by a diminishing degree, while the bond angle deviation and the ratio of TA to TO mode of amorphous network of c-Si samples increase continuously. This gives the dependence of short-range structural order of amorphous network of a-Si, nc-Si and c-Si samples on the ion fluence, which is related with the irradiation induced variation of local free energy. It is considered that the irradiation induced structural modification of silicon samples is mainly attributed to the nuclear energy loss. The irradiation effects of energetic heavy-ions on crystalline and amorphous phases of silicon have been discussed, respectively.

  17. Accumulation of dislocation loops in the α phase of Zr Excel alloy under heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Yu, Hongbing; Yao, Zhongwen; Idrees, Yasir; Zhang, He K.; Kirk, Mark A.; Daymond, Mark R.

    2017-08-01

    In-situ heavy ion irradiations were performed on the high Sn content Zr alloy 'Excel', measuring type dislocation loop accumulation up to irradiation damage doses of 10 dpa at a range of temperatures. The high content of Sn, which diffuses slowly, and the thin foil geometry of the sample provide a unique opportunity to study an extreme case where displacement cascades dominate the loop formation and evolution. The dynamic observation of dislocation loop evolution under irradiation at 200 °C reveals that type dislocation loops can form at very low dose (0.0025 dpa). The size of the dislocation loops increases slightly with irradiation damage dose. The mechanism controlling loop growth in this study is different from that in neutron irradiation; in this study, larger dislocation loops can condense directly from the interaction of displacement cascades and the high concentration of point defects in the matrix. The size of the dislocation loop is dependent on the point defect concentration in the matrix. A negative correlation between the irradiation temperature and the dislocation loop size was observed. A comparison between cascade dominated loop evolution (this study), diffusion dominated loop evolution (electron irradiation) and neutron irradiation suggests that heavy ion irradiation alone may not be enough to accurately reproduce neutron irradiation induced loop structures. An alternative method is proposed in this paper. The effects of Sn on the displacement cascades, defect yield, and the diffusion behavior of point defects are established.

  18. Carbon Ion Irradiation Effects on Pulsed Laser Deposited Titanium Nitride Thin Films

    NASA Astrophysics Data System (ADS)

    Mahmood, Khaliq; Bashir, Shazia; Akram, Mahreen; Hayat, Asma; Faizan-Ul-Haq; Saadat, Shahzad

    2015-02-01

    Pulse laser deposited thin films of TiN are irradiated by 1 MeV carbon (C+) ions beam for various doses ranging 0.4 to 2.8 × 1014 ions/cm2. Atomic force microscopy (AFM) analysis reveals the formation of hillocks like structures after ion irradiation. X-ray diffraction (XRD) investigations show that the film crystallinity increases for lower doses ranging from 0.4 to 1.2 × 1014 ions/cm2 and decreases for higher doses (2 to 2.8 × 1014 ions/cm2) of ions. No new bands are identified from Raman spectroscopy. However, a noticeable change in microhardness has been observed. The hillock densities as well as hardness are strongly dependent upon ion dose.

  19. Anisotropic dislocation loop nucleation in ion-irradiated MgAl sub 2 O sub 4

    SciTech Connect

    Zinkle, S.J.

    1991-01-01

    Polycrystalline disks of stoichiometric magnesium aluminate spinel (MgAl{sub 2}O{sub 4}) were irradiated with 2 MeV Al{sup +} ions at 650{degrees}C and subsequently analyzed in cross-section using transmission electron microscopy (TEM). Interstitial dislocation loops were observed on 110 and 11 habit planes. The population of loops on both sets of habit planes was strongly dependent on their orientation with respect to the ion beam direction. The density of loops with habit plane normals nearly perpendicular to the ion beam direction much higher than loops with habit plane normals nearly parallel to the ion beam direction. On the other hand, the loop size was nearly independent of habit plane orientation. This anisotropic loop nucleation does not occur in ion-irradiated metals such as copper. An additional anomaly associated with ion-irradiated spinel is that the loops on 111 planes were partially unfaulted with a Burgers vector of b = a/4<110>. Previous neutron irradiation studies have never reported unfaulted loops in stoichiometric spinel. Possible cause of the unusual response of spinel to ion irradiation are discussed. 12 refs., 14 figs.

  20. Magnetic patterning using ion irradiation for highly ordered CoPt alloys with perpendicular anisotropy

    SciTech Connect

    Abes, M.; Venuat, J.; Muller, D.; Carvalho, A.; Schmerber, G.; Beaurepaire, E.; Dinia, A.; Pierron-Bohnes, V.

    2004-12-15

    We used a combination of ion irradiation and e-beam lithography to magnetically pattern an ordered CoPt alloy with strong perpendicular magnetic anisotropy. Ion irradiation disorders the alloy and strongly reduces the magnetic anisotropy. Magnetic force microscopy showed a regular array of 1 {mu}m{sup 2} square dots with perpendicular anisotropy separated by 1 {mu}m large ranges with in-plane anisotropy. This is further confirmed by magnetic measurements, which showed that arrays protected by a 200 nm Pt layer present the same coercive field and the same perpendicular anisotropy as before irradiation. This is promising for applications in magnetic recording technologies.

  1. Characterization of Vacancy Defects in Carbon Ion Irradiated Graphite Using Positrons

    SciTech Connect

    Anto, C. Varghese; Arunkumar, J.; Rajaraman, R.; Nair, K. G. M.; Amarendra, G.

    2011-07-15

    Highly Oriented Pyrolytic Graphite samples are irradiated with 200 keV Carbon ions to fluences of 10{sup 14} and 10{sup 15} C{sup +} ions/cm{sup 2}. Depth resolved Doppler lineshape S-parameter exhibited large increase in peak damage regions of the sample, indicating the existence of irradiation induced vacancy defects. The depth profile of the defect region has been deduced from the analysis of the experimental data. It is found that divacancies are the dominant defects in the irradiated samples.

  2. Effect of Crystal Orientation on Self-Assembly Nanocones Formed on Tungsten Surface Induced by Helium Ion Irradiation and Annealing

    PubMed Central

    Huang, Shilin; Ran, Guang; Lei, Penghui; Wu, Shenghua; Chen, Nanjun; Li, Ning

    2016-01-01

    The self-assembly nanocone structures on the surface of polycrystalline tungsten were created by He+ ion irradiation and then annealing, and the resulting topography and morphology were characterized using atomic force microscopy and scanning electron microscopy. The cross-sectional samples of the self-assembly nanocones were prepared using an in situ–focused ion beam and then observed using transmission electron microscopy. The self-assembly nanocones were induced by the combined effect of He+ ion irradiation, the annealing process and the chromium impurity. The distribution characteristics, density and morphology of the nanocones exhibited a distinct difference relating to the crystal orientations. The highest density of the nanocones was observed on the grain surface with a (1 1 1) orientation, with the opposite for that with a (0 0 1) orientation and a medium value on the (1 0 1)-oriented grain. The size of the self-assembly nanocones increased with increasing the annealing time which met a power-law relationship. Irradiation-induced defects acted as the nucleation locations of the protrusions which attracted the migration of the tiny amount of chromium atoms. Under the action of temperature, the protrusions finally evolved into the nanocones. PMID:28335337

  3. Optical damage assessment and recovery investigation of hydrogen-ion and deuterium-ion plasma-irradiated bulk ZnO single crystals

    NASA Astrophysics Data System (ADS)

    Empizo, Melvin John F.; Yamanoi, Kohei; Mori, Kazuyuki; Iwano, Keisuke; Iwasa, Yuki; Minami, Yuki; Arita, Ren; Fukuda, Kazuhito; Takano, Keisuke; Shimizu, Toshihiko; Nakajima, Makoto; Yoshimura, Masashi; Sarukura, Nobuhiko; Norimatsu, Takayoshi; Hangyo, Masanori; Azechi, Hiroshi; Fukuda, Tsuguo; Singidas, Bess G.; Sarmago, Roland V.; Oya, Makoto; Ueda, Yoshio

    2017-05-01

    In realizing zinc oxide (ZnO) scintillator applications, we assess the optical damage and investigate the recovery of hydrogen-ion (H-ion) and deuterium-ion (D-ion) plasma-irradiated bulk ZnO single crystals. Hydrothermal-grown bulk crystals are irradiated with H-ion and D-ion beams with 1 keV energy and ˜ 10 20 m - 2 s - 1 flux. After irradiation, the single crystals exhibit decreased visible transparencies, redshifted ultraviolet (UV) emission peaks, shortened UV emission lifetimes, and suppressed visible emission bands. These changes in the optical transmittances and photoluminescence emissions are attributed to the generation of defects during irradiation and to the interaction of hydrogen with other defects and/or impurities. Although modified by ion irradiation, the optical properties of the ZnO crystals, except for the UV emission lifetimes, recover hours after without any sample treatment and only at room temperature. Compared with the H-ion-irradiated sample, the D-ion-irradiated crystal has a slower recovery which may be related to the ions' masses, energy losses, and absolute diffusivities. Our results nevertheless show that bulk ZnO single crystals exhibit resistance to and recovery from H-ion and D-ion irradiation and can therefore be used as scintillator materials for radiation detectors inside future fusion reactors.

  4. Induction and processing of oxidative clustered DNA lesions in 56Fe-ion-irradiated human monocytes.

    PubMed

    Tsao, Doug; Kalogerinis, Peter; Tabrizi, Isla; Dingfelder, Michael; Stewart, Robert D; Georgakilas, Alexandros G

    2007-07-01

    Space and cosmic radiation is characterized by energetic heavy ions of high linear energy transfer (LET). Although both low- and high-LET radiations can create oxidative clustered DNA lesions and double-strand breaks (DSBs), the local complexity of oxidative clustered DNA lesions tends to increase with increasing LET. We irradiated 28SC human monocytes with doses from 0-10 Gy of (56)Fe ions (1.046 GeV/ nucleon, LET = 148 keV/microm) and determined the induction and processing of prompt DSBs and oxidative clustered DNA lesions using pulsed-field gel electrophoresis (PFGE) and Number Average Length Analysis (NALA). The (56)Fe ions produced decreased yields of DSBs (10.9 DSB Gy(-1) Gbp(-1)) and clusters (1 DSB: approximately 0.8 Fpg clusters: approximately 0.7 Endo III clusters: approximately 0.5 Endo IV clusters) compared to previous results with (137)Cs gamma rays. The difference in the relative biological effectiveness (RBE) of the measured and predicted DSB yields may be due to the formation of spatially correlated DSBs (regionally multiply damaged sites) which result in small DNA fragments that are difficult to detect with the PFGE assay. The processing data suggest enhanced difficulty compared with gamma rays in the processing of DSBs but not clusters. At the same time, apoptosis is increased compared to that seen with gamma rays. The enhanced levels of apoptosis observed after exposure to (56)Fe ions may be due to the elimination of cells carrying high levels of persistent DNA clusters that are removed only by cell death and/or "splitting" during DNA replication.

  5. Observations of defect structure evolution in proton and Ni ion irradiated Ni-Cr binary alloys

    NASA Astrophysics Data System (ADS)

    Briggs, Samuel A.; Barr, Christopher M.; Pakarinen, Janne; Mamivand, Mahmood; Hattar, Khalid; Morgan, Dane D.; Taheri, Mitra; Sridharan, Kumar

    2016-10-01

    Two binary Ni-Cr model alloys with 5 wt% Cr and 18 wt% Cr were irradiated using 2 MeV protons at 400 and 500 °C and 20 MeV Ni4+ ions at 500 °C to investigate microstructural evolution as a function of composition, irradiation temperature, and irradiating ion species. Transmission electron microscopy (TEM) was applied to study irradiation-induced void and faulted Frank loops microstructures. Irradiations at 500 °C were shown to generate decreased densities of larger defects, likely due to increased barriers to defect nucleation as compared to 400 °C irradiations. Heavy ion irradiation resulted in a larger density of smaller voids when compared to proton irradiations, indicating in-cascade clustering of point defects. Cluster dynamics simulations were in good agreement with the experimental findings, suggesting that increases in Cr content lead to an increase in interstitial binding energy, leading to higher densities of smaller dislocation loops in the Ni-18Cr alloy as compared to the Ni-5Cr alloy.

  6. A novel way to estimate the nanoindentation hardness of only-irradiated layer and its application to ion irradiated Fe-12Cr alloy

    NASA Astrophysics Data System (ADS)

    Kim, Hoon-Seop; Lee, Dong-Hyun; Seok, Moo-Young; Zhao, Yakai; Kim, Woo-Jin; Kwon, Dongil; Jin, Hyung-Ha; Kwon, Junhyun; Jang, Jae-il

    2017-04-01

    While nanoindentation is a very useful tool to examine the mechanical properties of ion irradiated materials, there are some issues that should be considered in evaluating the properties of irradiated layer. In this study, in order to properly extract the hardness of only-irradiated layer from nanoindentation data, a new procedure is suggested in consideration of the geometry of indentation-induced plastic zone. By applying the procedure to an ion irradiated Fe-12Cr alloy, the reasonable results were obtained, validating its usefulness in the investigation of practical effect of irradiation on the mechanical behavior of future nuclear materials.

  7. Swift heavy ion irradiation induced nanograin formation in CdTe thin films

    NASA Astrophysics Data System (ADS)

    Survase, Smita; Narayan, Himanshu; Sulania, I.; Thakurdesai, Madhavi

    2016-11-01

    Swift Heavy Ion (SHI) irradiation is a unique technique for nanograin formation through grain fragmentation. Contrary to the generally reported SHI irradiation induced grain growth on CdTe thin films, we report fragmentation leading to nanograin formation. Thermally evaporated polycrystalline CdTe thin films were irradiated with 100 MeV 197Au, 107Ag and 58Ni ions beams up to a fluence of 5 × 1012 ions/cm2. Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) were carried out for surface analysis before and after irradiation. SEM micrographs indicate that the larger grains in the as-deposited films were fragmented into smaller grains due to irradiation. The extent of fragmentation was found to increase with increasing electronic energy loss (Se). AFM pictures also supported the irradiation induced fragmentation. Structural characterization was done using X-ray Diffraction (XRD) technique. The ion induced strain and dislocation density were calculated from the XRD data. Both the strain and dislocation density were found to increase with increasing Se . The observed grain fragmentation is explained on the basis of a combined effect of strain induced disintegration of grains after the Coulomb explosion, and an 'incomplete' re-crystallization of the molten thermal spikes. Moreover, the optical band gap Eg (1.5 eV for as-deposited film), determined from UV-vis spectroscopy, increased with Se, and possibly because of ion induced strain and defect annealing.

  8. Ion irradiation induced defect evolution in Ni and Ni-based FCC equiatomic binary alloys

    SciTech Connect

    Jin, Ke; Zhang, Yanwen; Bei, Hongbin

    2016-01-01

    In order to explore the chemical effects on radiation response of alloys with multi-principal elements, defect evolution under Au ion irradiation was investigated in the elemental Ni, equiatomic NiCo and NiFe alloys. Single crystals were successfully grown in an optical floating zone furnace and their (100) surfaces were irradiated with 3 MeV Au ions at fluences ranging from 1 × 1013 to 5 × 1015 ions cm–2 at room temperature. The irradiation-induced defect evolution was analyzed by using ion channeling technique. Experiment shows that NiFe is more irradiation-resistant than NiCo and pure Ni at low fluences. With continuously increasing the ion fluences, damage level is eventually saturated for all materials but at different dose levels. The saturation level in pure Ni appears at relatively lower irradiation fluence than the alloys, suggesting that damage accumulation slows down in the alloys. Here, under high-fluence irradiations, pure Ni has wider damage ranges than the alloys, indicating that defects in pure Ni have high mobility.

  9. Ion irradiation induced defect evolution in Ni and Ni-based FCC equiatomic binary alloys

    DOE PAGES

    Jin, Ke; Zhang, Yanwen; Bei, Hongbin

    2016-01-01

    In order to explore the chemical effects on radiation response of alloys with multi-principal elements, defect evolution under Au ion irradiation was investigated in the elemental Ni, equiatomic NiCo and NiFe alloys. Single crystals were successfully grown in an optical floating zone furnace and their (100) surfaces were irradiated with 3 MeV Au ions at fluences ranging from 1 × 1013 to 5 × 1015 ions cm–2 at room temperature. The irradiation-induced defect evolution was analyzed by using ion channeling technique. Experiment shows that NiFe is more irradiation-resistant than NiCo and pure Ni at low fluences. With continuously increasing themore » ion fluences, damage level is eventually saturated for all materials but at different dose levels. The saturation level in pure Ni appears at relatively lower irradiation fluence than the alloys, suggesting that damage accumulation slows down in the alloys. Here, under high-fluence irradiations, pure Ni has wider damage ranges than the alloys, indicating that defects in pure Ni have high mobility.« less

  10. Influence of Oxygen ions irradiation on Polyaniline/Single Walled Carbon Nanotubes nanocomposite

    NASA Astrophysics Data System (ADS)

    Patil, Harshada K.; Deshmukh, Megha A.; Gaikwad, Sumedh D.; Bodkhe, Gajanan A.; Asokan, K.; Yasuzawa, Mikito; Koinkar, Pankaj; Shirsat, Mahendara D.

    2017-01-01

    Influence of Oxygen ions (100 MeV) irradiation on Polyaniline (PANI)/Single Walled Carbon Nanotubes (SWNTs) nanocomposite was studied in the present investigation. PANI/SWNTs nanocomposite was synthesized by electrochemical Cyclic Voltammetry technique. Nanocomposite was exposed under SHI irradiation of Oxygen (100 MeV) ions for three different fluences such as 1×1010 ions/cm2, 5×1010 ions/cm2 and 1×1011 ions/cm2. The SHI irradiated PANI/SWNTs nanocomposite was investigated by using morphological (AFM), structural (XRD) and spectroscopy (FTIR) characterization. AFM study exhibits effects of SHI irradiation on morphology of the nanocomposite and root mean square roughness of the nanocomposite is observed to be decreased as fluence was increased. The FTIR absorption spectrum exhibits formation of new functional sites with the increase in intensity of absorption peaks, due to SHI irradiation. X-Ray Diffraction studies show a gradual decrease in the crystalline nature of the nanocomposite upon irradiation.

  11. Ion irradiation induced defect evolution in Ni and Ni-based FCC equiatomic binary alloys

    NASA Astrophysics Data System (ADS)

    Jin, K.; Bei, H.; Zhang, Y.

    2016-04-01

    In order to explore the chemical effects on radiation response of alloys with multi-principal elements, defect evolution under Au ion irradiation was investigated in the elemental Ni, equiatomic NiCo and NiFe alloys. Single crystals were successfully grown in an optical floating zone furnace and their (100) surfaces were irradiated with 3 MeV Au ions at fluences ranging from 1 × 1013 to 5 × 1015 ions cm-2 at room temperature. The irradiation-induced defect evolution was analyzed by using ion channeling technique. Experiment shows that NiFe is more irradiation-resistant than NiCo and pure Ni at low fluences. With continuously increasing the ion fluences, damage level is eventually saturated for all materials but at different dose levels. The saturation level in pure Ni appears at relatively lower irradiation fluence than the alloys, suggesting that damage accumulation slows down in the alloys. Under high-fluence irradiations, pure Ni has wider damage ranges than the alloys, indicating that defects in pure Ni have high mobility.

  12. Influence of irradiation spectrum and implanted ions on the amorphization of ceramics

    SciTech Connect

    Zinkle, S.J.; Snead, L.L.

    1995-12-31

    Polycrystalline Al2O3, magnesium aluminate spinel (MgAl2O4), MgO, Si3N4, and SiC were irradiated with various ions at 200-450 K, and microstructures were examined following irradiation using cross-section TEM. Amorphization was not observed in any of the irradiated oxide ceramics, despsite damage energy densities up to {similar_to}7 keV/atom (70 displacements per atom). On the other hand, SiC readily amorphized after damage levels of {similar_to}0.4 dpa at room temperature (RT). Si3N4 exhibited intermediate behavior; irradiation with Fe{sup 2+} ions at RT produced amorphization in the implanted ion region after damage levels of {similar_to}1 dpa. However, irradiated regions outside the implanted ion region did not amorphize even after damage levels > 5 dpa. The amorphous layer in the Fe-implanted region of Si3N4 did not appear if the specimen was simultaneoulsy irradiated with 1-MeV He{sup +} ions at RT. By comparison with published results, it is concluded that the implantation of certain chemical species has a pronounced effect on the amorphization threshold dose of all five materials. Intense ionizing radiation inhibits amorphization in Si3N4, but does not appear to significantly influence the amorphization of SiC.

  13. Production of a thermal stress resistant mutant Euglena gracilis strain using Fe-ion beam irradiation.

    PubMed

    Yamada, Koji; Kazama, Yusuke; Mitra, Sharbanee; Marukawa, Yuka; Arashida, Ryo; Abe, Tomoko; Ishikawa, Takahiro; Suzuki, Kengo

    2016-08-01

    Euglena gracilis is a common phytoplankton species, which also has motile flagellate characteristics. Recent research and development has enabled the industrial use of E. gracilis and selective breeding of this species is expected to further expand its application. However, the production of E. gracilis nuclear mutants is difficult because of the robustness of its genome. To establish an efficient mutation induction procedure for E. gracilis, we employed Fe-ion beam irradiation in the RIKEN RI beam factory. A decrease in the survival rate was observed with the increase in irradiation dose, and the upper limit used for E. gracilis selective breeding was around 50 Gy. For a practical trial of Fe-ion irradiation, we conducted a screening to isolate high-temperature-tolerant mutants. The screening yielded mutants that proliferated faster than the wild-type strain at 32 °C. Our results demonstrate the effectiveness of heavy-ion irradiation on E. gracilis selective breeding.

  14. HRTEM and FTIR investigation of nanosized zinc ferrite irradiated with 100 MeV oxygen ions.

    PubMed

    Singh, Jitendra Pal; Dixit, Gagan; Srivastava, R C; Negi, Puneet; Agrawal, H M; Kumar, Ravi

    2013-04-15

    Present work aims to investigate effect of 100 MeV oxygen ion irradiation on the vibrational modes of zinc ferrite nanoparticles. Nanosize zinc ferrite systems of different crystallite size ranging from 12-62 nm were irradiated at the fluence of 1×10(13) and 5×10(13) ions/cm(2). High resolution transmission electron micrograph study indicates the structural disorder induced by ion irradiation. Bands corresponding to various vibrational modes in Fourier transform infrared spectra exhibit changes and are affected by the crystallite size/microstructure of pristine samples. The irradiation induced changes are dominated for sample ZF1000. Copyright © 2013 Elsevier B.V. All rights reserved.

  15. Tailoring nonlinear optical properties of Bi2Se3 through ion irradiation

    NASA Astrophysics Data System (ADS)

    Tan, Yang; Guo, Zhinan; Shang, Zhen; Liu, Fang; Böttger, Roman; Zhou, Shengqiang; Shao, Jundong; Yu, Xuefeng; Zhang, Han; Chen, Feng

    2016-02-01

    The nonlinear optical property of topological insulator bismuth selenide (Bi2Se3) is found to be well-tailored through ion irradiation by intentionally introducing defects. The increase of the optical modulation depth sensitively depends on the careful selection of the irradiation condition. By implementing the ion irradiated Bi2Se3 film as an optical saturable absorber device for the Q-switched wave-guide laser, an enhanced laser performance has been obtained including narrower pulse duration and higher peak power. Our work provides a new approach of tailoring the nonlinear optical properties of materials through ion irradiation, a well-developed chip-technology, which could find wider applicability to other layered two-dimensional materials beyond topological insulators, such as graphene, MoS2, black phosphours etc.

  16. Tailoring nonlinear optical properties of Bi2Se3 through ion irradiation

    PubMed Central

    Tan, Yang; Guo, Zhinan; Shang, Zhen; Liu, Fang; Böttger, Roman; Zhou, Shengqiang; Shao, Jundong; Yu, Xuefeng; Zhang, Han; Chen, Feng

    2016-01-01

    The nonlinear optical property of topological insulator bismuth selenide (Bi2Se3) is found to be well-tailored through ion irradiation by intentionally introducing defects. The increase of the optical modulation depth sensitively depends on the careful selection of the irradiation condition. By implementing the ion irradiated Bi2Se3 film as an optical saturable absorber device for the Q-switched wave-guide laser, an enhanced laser performance has been obtained including narrower pulse duration and higher peak power. Our work provides a new approach of tailoring the nonlinear optical properties of materials through ion irradiation, a well-developed chip-technology, which could find wider applicability to other layered two-dimensional materials beyond topological insulators, such as graphene, MoS2, black phosphours etc. PMID:26888223

  17. Swift Heavy Ion Irradiation Effect On Nanometer Range W/Fe Multilayers

    SciTech Connect

    Bagchi, Sharmistha; Jani, N. P. Lalla Snehal; Lakshmi, N.

    2010-10-04

    The present study reports the effect of swift heavy ion irradiation on structural and magnetic properties of sputtered Fe/W multilayer structure (MLS) having a bilayer composition of [W(30A)/Fe(20A)]{sub 10BL}. The MLS was irradiated by 120 MeV Au{sup 9+} ions up to fluence of 4x10{sup 13} ions/cm{sup 2}. Structural study of pristine and irradiated MLS reveals that intra-layer microstructure of Fe-layers in the MLS becomes nano-crystalline on irradiation. Magnetic studies show increase in coercivity at higher fluence which may be due to increase in surface and interface roughness after recrystallization of Fe-layers.

  18. Ion microbeam irradiation for radiobiology and radical chemistry: status and prospect

    NASA Astrophysics Data System (ADS)

    Khodja, H.

    2011-01-01

    Ion microbeams are commonly used to study local irradiation effects in living cells, as it has been established that ion beam irradiations can lead to deleterious changes in cells that are not struck directly by the microbeam. Such changes, which take place over distances long compared to the size of the irradiation spot and for times long compared to the time of irradiation, are collectively termed radiation-induced bystander effect or RIBE. Free-radical chemistry is frequently invoked to explain the RIBE but no unified model is available at present. Ion microbeams when coupled with advanced methods for observing free radicals are the tools of choice for investigating the chemistry and biological processes governing RIBE.

  19. Amorphization resistance of nano-engineered SiC under heavy ion irradiation

    SciTech Connect

    Imada, Kenta; Ishimaru, Manabu; Xue, Haizhou; Zhang, Yanwen; Shannon, Steven C.; Weber, William J.

    2016-06-19

    Silicon carbide (SiC) with a high-density of planar defects (hereafter, ‘nano-engineered SiC’) and epitaxially-grown single-crystalline 3C-SiC were simultaneously irradiated with Au ions at room temperature, in order to compare their relative resistance to radiation-induced amorphization. Furthermore, it was found that the local threshold dose for amorphization is comparable for both samples under 2 MeV Au ion irradiation; whereas, nano-engineered SiC exhibits slightly greater radiation tolerance than single crystalline SiC under 10 MeV Au irradiation. Under 10 MeV Au ion irradiation, the dose for amorphization increased by about a factor of two in both nano-engineered and single crystal SiC due to the local increase in electronic energy loss that enhanced dynamic recovery.

  20. Ion irradiation effects on conduction in single-wall carbon nanotube networks

    NASA Astrophysics Data System (ADS)

    Skákalová, V.; Kaiser, A. B.; Osváth, Z.; Vértesy, G.; Biró, L. P.; Roth, S.

    2008-03-01

    We have measured how irradiation by Ar+ and N+ ions modifies electronic conduction in single-wall carbon nanotube (SWNT) networks, finding dramatically different effects for different thicknesses. For very thin transparent networks, ion irradiation increases localization of charge carriers and reduces the variable-range hopping conductivity, especially at low temperatures. However, for thick networks (SWNT paper) showing metallic conductivity, we find a relatively sharp peak in conductivity as a function of irradiation dose. Our investigation of this peak reveals the important role of thermal annealing extending beyond the range of the irradiating ions, and shows the dependence on the morphology of the samples. We propose a simple model that accounts for the temperature-dependent conductivity.

  1. Amorphization resistance of nano-engineered SiC under heavy ion irradiation

    SciTech Connect

    Imada, Kenta; Ishimaru, Manabu; Xue, Haizhou; Zhang, Yanwen; Shannon, Steven C.; Weber, William J.

    2016-06-19

    Silicon carbide (SiC) with a high-density of planar defects (hereafter, ‘nano-engineered SiC’) and epitaxially-grown single-crystalline 3C-SiC were simultaneously irradiated with Au ions at room temperature, in order to compare their relative resistance to radiation-induced amorphization. Furthermore, it was found that the local threshold dose for amorphization is comparable for both samples under 2 MeV Au ion irradiation; whereas, nano-engineered SiC exhibits slightly greater radiation tolerance than single crystalline SiC under 10 MeV Au irradiation. Under 10 MeV Au ion irradiation, the dose for amorphization increased by about a factor of two in both nano-engineered and single crystal SiC due to the local increase in electronic energy loss that enhanced dynamic recovery.

  2. Amorphization resistance of nano-engineered SiC under heavy ion irradiation

    DOE PAGES

    Imada, Kenta; Ishimaru, Manabu; Xue, Haizhou; ...

    2016-06-19

    Silicon carbide (SiC) with a high-density of planar defects (hereafter, ‘nano-engineered SiC’) and epitaxially-grown single-crystalline 3C-SiC were simultaneously irradiated with Au ions at room temperature, in order to compare their relative resistance to radiation-induced amorphization. Furthermore, it was found that the local threshold dose for amorphization is comparable for both samples under 2 MeV Au ion irradiation; whereas, nano-engineered SiC exhibits slightly greater radiation tolerance than single crystalline SiC under 10 MeV Au irradiation. Under 10 MeV Au ion irradiation, the dose for amorphization increased by about a factor of two in both nano-engineered and single crystal SiC due tomore » the local increase in electronic energy loss that enhanced dynamic recovery.« less

  3. Transmission electron microscopy of the amorphization of copper indium diselenide by in situ ion irradiation

    SciTech Connect

    Hinks, J. A.; Edmondson, P. D.

    2012-03-01

    Copper indium diselenide (CIS), along with its derivatives Cu(In,Ga)(Se,S){sub 2}, is a prime candidate for use in the absorber layers of photovoltaic devices. Due to its ability to resist radiation damage, it is particularly well suited for use in extraterrestrial and other irradiating environments. However, the nature of its radiation hardness is not well understood. In this study, transmission electron microscopy (TEM) with in situ ion irradiation was used to monitor the dynamic microstructural effects of radiation damage on CIS. Samples were bombarded with 400 keV xenon ions to create large numbers of atomic displacements within the thickness of the TEM samples and thus explore the conditions under which, if any, CIS could be amorphized. By observing the impact of heavily damaging radiation in situ--rather than merely the end-state possible in ex situ experiments--at the magnifications allowed by TEM, it was possible to gain an understanding of the atomistic processes at work and the underlying mechanism that give rise to the radiation hardness of CIS. At 200 K and below, it was found that copper-poor samples could be amorphized and copper-rich samples could not. This difference in behavior is linked to the crystallographic phases that are present at different compositions. Amorphization was found to progress via a combination of one- and two-hit processes. The radiation hardness of CIS is discussed in terms of crystallographic structures/defects and the consequences these have for the ability of the material to recover from the effects of displacing radiation.

  4. Tuning the conductivity of vanadium dioxide films on silicon by swift heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Hofsäss, H.; Ehrhardt, P.; Gehrke, H.-G.; Brötzmann, M.; Vetter, U.; Zhang, K.; Krauser, J.; Trautmann, C.; Ko, C.; Ramanathan, S.

    2011-09-01

    We demonstrate the generation of a persistent conductivity increase in vanadium dioxide thin films grown on single crystal silicon by irradiation with 1 GeV 238U swift heavy ions at room temperature. VO2 undergoes a temperature driven metal-insulator-transition (MIT) at 67 °C. After room temperature ion irradiation with high electronic energy loss of 50 keV/nm the conductivity of the films below the transition temperature is strongly increased proportional to the ion fluence of 5.109 U/cm2 and 1.1010 U/cm2. At high temperatures the conductivity decreases slightly. The ion irradiation slightly reduces the MIT temperature. This observed conductivity change is persistent and remains after heating the samples above the transition temperature and subsequent cooling. Low temperature measurements down to 15 K show no further MIT below room temperature. Although the conductivity increase after irradiation at such low fluences is due to single ion track effects, atomic force microscopy (AFM) measurements do not show surface hillocks, which are characteristic for ion tracks in other materials. Conductive AFM gives no evidence for conducting ion tracks but rather suggests the existence of conducting regions around poorly conducting ion tracks, possible due to stress generation. Another explanation of the persistent conductivity change could be the ion-induced modification of a high resistivity interface layer formed during film growth between the vanadium dioxide film and the n-Silicon substrate. The swift heavy ions may generate conducting filaments through this layer, thus increasing the effective contact area. Swift heavy ion irradiation can thus be used to tune the conductivity of VO2 films on silicon substrates.

  5. Control of the local devitrification on oxyfluoride glass doped with Er{sup 3+} ions under diode laser irradiation

    SciTech Connect

    Gonzalez-Perez, S.; Martin, I. R.; Jaque, D.; Haro-Gonzalez, P.; Capuj, N.

    2010-11-15

    Temperature control of the devitrification process in an erbium doped oxyfluoride glass under laser irradiation is reported. The green upconversion emissions around 525 and 545 nm originated from the thermalized {sup 2}H{sub 11/2} and {sup 4}S{sub 3/2} levels were studied when the glass structure changes to glass ceramic during irradiation with a laser beam. Power dependence of the fluorescence intensity ratio was used to determine the temperature of the irradiated zone. The transition from glass to glass ceramic takes place under 2300 mW of laser power with an estimated temperature around 783 K. This result agrees with the one obtained in the samples devitrified under conventional furnace treatment. Therefore, the estimation of the temperature of the irradiated zone through the fluorescence intensity ratio method allows a controlled devitrification. Moreover, an irradiated line has been written in the glass showing an important diffusion of the Pb{sup 2+} and F{sup -} ions. These results confirm that nanocrystals have been created due to the laser action.

  6. Control of the local devitrification on oxyfluoride glass doped with Er3+ ions under diode laser irradiation

    NASA Astrophysics Data System (ADS)

    González-Pérez, S.; Martín, I. R.; Jaque, D.; Haro-González, P.; Capuj, N.

    2010-11-01

    Temperature control of the devitrification process in an erbium doped oxyfluoride glass under laser irradiation is reported. The green upconversion emissions around 525 and 545 nm originated from the thermalized H211/2 and S43/2 levels were studied when the glass structure changes to glass ceramic during irradiation with a laser beam. Power dependence of the fluorescence intensity ratio was used to determine the temperature of the irradiated zone. The transition from glass to glass ceramic takes place under 2300 mW of laser power with an estimated temperature around 783 K. This result agrees with the one obtained in the samples devitrified under conventional furnace treatment. Therefore, the estimation of the temperature of the irradiated zone through the fluorescence intensity ratio method allows a controlled devitrification. Moreover, an irradiated line has been written in the glass showing an important diffusion of the Pb2+ and F- ions. These results confirm that nanocrystals have been created due to the laser action.

  7. Vibrational Spectroscopy in Ion-Irradiated Carbon-Based Thin Films

    NASA Astrophysics Data System (ADS)

    Compagnini, Giuseppe; Puglisi, Orazio; Baratta, Giuseppe A.; Strazzulla, Giovanni

    In this work we present and discuss some selected experiments on ion-irradiated carbon-based thin films. Vibrational spectroscopy is used to investigate the materials structure and to explore the mechanisms of ion beam-induced modifications in many carbon solids such as crystalline carbon and carbon alloys, hydrocarbon molecules and exotic carbon species.

  8. Augmentation of thermoelectric performance of VO2 thin films irradiated by 200 MeV Ag9+-ions

    NASA Astrophysics Data System (ADS)

    Khan, G. R.; Kandasami, A.; Bhat, B. A.

    2016-06-01

    Swift Heavy Ion (SHI) irradiation with 200 MeV Ag9+-ion beam at ion fluences of 1E11, 5E11, 1E12, and 5E12 for tuning of electrical transport properties of VO2 thin films fabricated by so-gel technique on alumina substrates has been demonstrated in the present paper. The point defects created by SHI irradiation modulate metal to insulator phase transition temperature, carrier concentration, carrier mobility, electrical conductivity, and Seebeck coefficient of VO2 thin films. The structural properties of the films were characterized by XRD and Raman spectroscopy and crystallite size was found to decrease upon irradiation. The atomic force microscopy revealed that the surface roughness of specimens first decreased and then increased with increasing fluence. Both resistance as well as Seebeck coefficient measurements demonstrated that all the samples exhibit metal-insulator phase transition and the transition temperatures decreases with increasing fluence. Hall effect measurements exhibited that carrier concentration increased continuously with increasing fluence which resulted in an increase of electrical conductivity by several orders of magnitude in the insulating phase. Seebeck coefficient in insulating phase remained almost constant in spite of an increase in the electrical conductivity by several orders of magnitude making SHI irradiation an alternative stratagem for augmentation of thermoelectric performance of the materials. The carrier mobility at room temperature decreased up to the beam fluence of 5E11 and then started increasing whereas Seebeck coefficient in metallic state first increased with increasing ion beam fluence up to 5E11 and thereafter decreased. Variation of these electrical transport parameters has been explained in detail.

  9. Antiradiation Vaccine: Technology Development- Radiation Tolerance,Prophylaxis, Prevention And Treatment Of Clinical Presentation After Heavy Ion Irradiation.

    NASA Astrophysics Data System (ADS)

    Popov, Dmitri; Maliev, Slava; Jones, Jeffrey

    Introduction: Research in the field of biological effects of heavy charged particles is necessary for both heavy-ion therapy (hadrontherapy) and protection from the exposure to galactic cosmic radiation in long-term manned space missions.[Durante M. 2004] In future crew of long-term manned missions could operate in exremely high hadronic radiation areas of space and will not survive without effective radiation protection. An Antiradiation Vaccine (AV) must be an important part of a countermeasures regimen for efficient radiation protection purposes of austronauts-cosmonauts-taukonauts: immune-prophylaxis and immune-therapy of acute radiation toxic syndromes developed after heavy ion irradiation. New technology developed (AV) for the purposes of radiological protection and improvement of radiation tolerance and it is quite important to create protective immune active status which prevent toxic reactions inside a human body irradiated by high energy hadrons.[Maliev V. et al. 2006, Popov D. et al.2008]. High energy hadrons produce a variety of secondary particles which play an important role in the energy deposition process, and characterise their radiation qualities [Sato T. et al. 2003] Antiradiation Vaccine with specific immune-prophylaxis by an anti-radiation vaccine should be an important part of medical management for long term space missions. Methods and experiments: 1. Antiradiation vaccine preparation standard, mixture of toxoid form of Radiation Toxins [SRD-group] which include Cerebrovascular RT Neurotoxin, Cardiovascular RT Neurotoxin, Gastrointestinal RT Neurotoxin, Hematopoietic RT Hematotoxin. Radiation Toxins of Radiation Determinant Group isolated from the central lymph of gamma-irradiated animals with Cerebrovascular, Cardiovascular, Gastro-intestinal, Hematopoietic forms of ARS. Devices for radiation are "Panorama", "Puma". 2. Heavy ion exposure was accomplished at Department of Research Institute of Nuclear Physics, Dubna, Russia. The heavy ions

  10. Fast ion conductivity in strained defect-fluorite structure created by ion tracks in Gd2Ti2O7

    PubMed Central

    Aidhy, Dilpuneet S.; Sachan, Ritesh; Zarkadoula, Eva; Pakarinen, Olli; Chisholm, Matthew F.; Zhang, Yanwen; Weber, William J.

    2015-01-01

    The structure and ion-conducting properties of the defect-fluorite ring structure formed around amorphous ion-tracks by swift heavy ion irradiation of Gd2Ti2O7 pyrochlore are investigated. High angle annular dark field imaging complemented with ion-track molecular dynamics simulations show that the atoms in the ring structure are disordered, and have relatively larger cation-cation interspacing than in the bulk pyrochlore, illustrating the presence of tensile strain in the ring region. Density functional theory calculations show that the non-equilibrium defect-fluorite structure can be stabilized by tensile strain. The pyrochlore to defect-fluorite structure transformation in the ring region is predicted to be induced by recrystallization during a melt-quench process and stabilized by tensile strain. Static pair-potential calculations show that planar tensile strain lowers oxygen vacancy migration barriers in pyrochlores, in agreement with recent studies on fluorite and perovskite materials. In view of these results, it is suggested that strain engineering could be simultaneously used to stabilize the defect-fluorite structure and gain control over its high ion-conducting properties. PMID:26555848

  11. Fast ion conductivity in strained defect-fluorite structure created by ion tracks in Gd2Ti2O7

    DOE PAGES

    Aidhy, Dilpuneet S.; Sachan, Ritesh; Zarkadoula, Eva; ...

    2015-11-10

    The structure and ion-conducting properties of the defect-fluorite ring structure formed around amorphous ion-tracks by swift heavy ion irradiation of Gd2Ti2O7 pyrochlore are investigated. High angle annular dark field imaging complemented with ion-track molecular dynamics simulations show that the atoms in the ring structure are disordered, and have relatively larger cation-cation interspacing than in the bulk pyrochlore, illustrating the presence of tensile strain in the ring region. Density functional theory calculations show that the non-equilibrium defect-fluorite structure can be stabilized by tensile strain. The pyrochlore to defect-fluorite structure transformation in the ring region is predicted to be induced by recrystallizationmore » during a melt-quench process and stabilized by tensile strain. Static pair-potential calculations show that planar tensile strain lowers oxygen vacancy migration barriers in pyrochlores, in agreement with recent studies on fluorite and perovskite materials. Lastly, in view of these results, it is suggested that strain engineering could be simultaneously used to stabilize the defect-fluorite structure and gain control over its high ion-conducting properties.« less

  12. Fast ion conductivity in strained defect-fluorite structure created by ion tracks in Gd2Ti2O7.

    PubMed

    Aidhy, Dilpuneet S; Sachan, Ritesh; Zarkadoula, Eva; Pakarinen, Olli; Chisholm, Matthew F; Zhang, Yanwen; Weber, William J

    2015-11-10

    The structure and ion-conducting properties of the defect-fluorite ring structure formed around amorphous ion-tracks by swift heavy ion irradiation of Gd2Ti2O7 pyrochlore are investigated. High angle annular dark field imaging complemented with ion-track molecular dynamics simulations show that the atoms in the ring structure are disordered, and have relatively larger cation-cation interspacing than in the bulk pyrochlore, illustrating the presence of tensile strain in the ring region. Density functional theory calculations show that the non-equilibrium defect-fluorite structure can be stabilized by tensile strain. The pyrochlore to defect-fluorite structure transformation in the ring region is predicted to be induced by recrystallization during a melt-quench process and stabilized by tensile strain. Static pair-potential calculations show that planar tensile strain lowers oxygen vacancy migration barriers in pyrochlores, in agreement with recent studies on fluorite and perovskite materials. In view of these results, it is suggested that strain engineering could be simultaneously used to stabilize the defect-fluorite structure and gain control over its high ion-conducting properties.

  13. Generation of superparamagnetism in metallic α-iron by swift heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Kuzmann, E.; Stichleutner, S.; Homonnay, Z.; Havancsák, K.; Chisholm, C. U.; El-Sharif, M.; Skuratov, V. A.; Nakanishi, A.; Nomura, K.

    2016-10-01

    57Fe conversion electron Mössbauer spectroscopy was used to study the effect of swift heavy ion irradiation on electrochemically deposited metallic pure α-iron. We succeeded in preparing superparamagnetic iron by irradiating the electrochemically prepared thin α-iron films using 247 MeV Kr ions with a fluence of 1×1013 ion cm-2 which converted 50% of crystalline α-iron into amorphous and superparamagnetic phases, the latter being >20%. The results are discussed in terms of the thermal spike model for the formation of the amorphous phase which could be essential for the formation of superparamagnetic iron.

  14. Strain-dependent Damage in Mouse Lung After Carbon Ion Irradiation

    SciTech Connect

    Moritake, Takashi; Fujita, Hidetoshi; Yanagisawa, Mitsuru; Nakawatari, Miyako; Imadome, Kaori; Nakamura, Etsuko; Iwakawa, Mayumi; Imai, Takashi

    2012-09-01

    Purpose: To examine whether inherent factors produce differences in lung morbidity in response to carbon ion (C-ion) irradiation, and to identify the molecules that have a key role in strain-dependent adverse effects in the lung. Methods and Materials: Three strains of female mice (C3H/He Slc, C57BL/6J Jms Slc, and A/J Jms Slc) were locally irradiated in the thorax with either C-ion beams (290 MeV/n, in 6 cm spread-out Bragg peak) or with {sup 137}Cs {gamma}-rays as a reference beam. We performed survival assays and histologic examination of the lung with hematoxylin-eosin and Masson's trichrome staining. In addition, we performed immunohistochemical staining for hyaluronic acid (HA), CD44, and Mac3 and assayed for gene expression. Results: The survival data in mice showed a between-strain variance after C-ion irradiation with 10 Gy. The median survival time of C3H/He was significantly shortened after C-ion irradiation at the higher dose of 12.5 Gy. Histologic examination revealed early-phase hemorrhagic pneumonitis in C3H/He and late-phase focal fibrotic lesions in C57BL/6J after C-ion irradiation with 10 Gy. Pleural effusion was apparent in C57BL/6J and A/J mice, 168 days after C-ion irradiation with 10 Gy. Microarray analysis of irradiated lung tissue in the three mouse strains identified differential expression changes in growth differentiation factor 15 (Gdf15), which regulates macrophage function, and hyaluronan synthase 1 (Has1), which plays a role in HA metabolism. Immunohistochemistry showed that the number of CD44-positive cells, a surrogate marker for HA accumulation, and Mac3-positive cells, a marker for macrophage infiltration in irradiated lung, varied significantly among the three mouse strains during the early phase. Conclusions: This study demonstrated a strain-dependent differential response in mice to C-ion thoracic irradiation. Our findings identified candidate molecules that could be implicated in the between-strain variance to early

  15. Enhancement of SPHK1 in vitro by carbon ion irradiation in oral squamous cell carcinoma

    SciTech Connect

    Higo, Morihiro; Uzawa, Katsuhiro . E-mail: uzawak@faculty.chiba-u.jp; Kawata, Tetsuya; Kato, Yoshikuni; Kouzu, Yukinao; Yamamoto, Nobuharu; Shibahara, Takahiko; Mizoe, Jun-etsu; Ito, Hisao; Tsujii, Hirohiko; Tanzawa, Hideki

    2006-07-01

    Purpose The purpose of this study was to assess the gene expression changes in oral squamous cell carcinoma (OSCC) cells after carbon ion irradiation. Methods and Materials Three OSCC cell lines (HSC2, Ca9-22, and HSC3) were irradiated with accelerated carbon ion beams or X-rays using three different doses. The cellular sensitivities were determined by clonogenic survival assay. To identify genes the expression of which is influenced by carbon ion irradiation in a dose-dependent manner, we performed Affymetrix GeneChip analysis with HG-U133 plus 2.0 arrays containing 54,675 probe sets. The identified genes were analyzed using the Ingenuity Pathway Analysis Tool to investigate the functional network and gene ontology. Changes in mRNA expression in the genes were assessed by real-time reverse transcriptase-polymerase chain reaction. Results We identified 98 genes with expression levels that were altered significantly at least twofold in each of the three carbon-irradiated OSCC cell lines at all dose points compared with nonirradiated control cells. Among these, SPHK1, the expression of which was significantly upregulated by carbon ion irradiation, was modulated little by X-rays. The function of SPHK1 related to cellular growth and proliferation had the highest p value (p = 9.25e-7 to 2.19e-2). Real-time reverse transcriptase-polymerase chain reaction analysis showed significantly elevated SPHK1 expression levels after carbon ion irradiation (p < 0.05), consistent with microarray data. Clonogenic survival assay indicated that carbon ion irradiation could induce cell death in Ca9-22 cells more effectively than X-rays. Conclusions Our findings suggest that SPHK1 helps to elucidate the molecular mechanisms and processes underlying the biologic response to carbon ion beams in OSCC.

  16. Ion irradiation of graphene on Ir(111): From trapping to blistering

    NASA Astrophysics Data System (ADS)

    Herbig, Charlotte; Åhlgren, E. Harriet; Valerius, Philipp; Schröder, Ulrike A.; Martínez-Galera, Antonio J.; Arman, Mohammad A.; Kotakoski, Jani; Knudsen, Jan; Krasheninnikov, Arkady V.; Michely, Thomas

    Graphene grown epitaxially on Ir(111) is irradiated with low energy noble gas ions and the processes induced by atomic collision and subsequent annealing are analyzed using scanning tunneling microscopy, low energy electron diffraction, X-ray photoelectron diffraction and thermal desorption spectroscopy. Upon room temperature ion irradiation graphene amorphizes and recovers its crystalline structure during annealing. The energetic noble gas projectiles are trapped with surprisingly high efficiency under the graphene cover up to extremely high temperatures beyond 1300K. The energy, angle, and ion species dependence of trapping are quantified. At elevated temperatures the trapped gas forms well developed and highly pressurized blisters under the graphene cover. We use molecular dynamics simulations and ab initio calculations to elucidate the trapping mechanism and its thermal robustness. Similar trapping and blistering are observed after ion irradiation of a single layer of hexagonal boron nitride on Ir(111) and we speculate on the generality of the observed phenomena.

  17. Pattern-induced magnetic anisotropy in FePt thin films by ion irradiation

    SciTech Connect

    Jaafar, M.; Sanz, R.; McCord, J.; Jensen, J.; Schaefer, R.; Vazquez, M.; Asenjo, A.

    2011-03-01

    The magnetic properties of FePt thin films have been modified by exposing the samples to irradiation of 4 MeV Cl{sup 2+} ions. Patterned magnetic films, without modified topographical profile, were fabricated by irradiating the films through a shadowing micrometric mask. The structural changes, ascribed to the ion-beam-induced amorphization of the thin films, promote the modification of the magnetic anisotropy. In particular, the out-of-plane component of the magnetization decreases simultaneously with an enhancement of in-plane anisotropy by increasing ion fluence. Moreover, the nonirradiated regions present unexpected anisotropic behavior owing to the stray field of the irradiated regions. The control of this effect, which can have unwished consequences for the patterning of magnetic properties by ion bombardment, needs to be suitably addressed.

  18. Magnetic states controlled by energetic ion irradiation in FeRh thin films

    SciTech Connect

    Fujita, Nao.; Kosugi, S.; Matsui, T.; Iwase, A.; Saitoh, Y.; Kaneta, Y.; Kume, K.; Batchuluun, T.; Ishikawa, N.

    2010-05-15

    Changes in magnetic properties and lattice structure of FeRh films by 180 keV-10 MeV ion (H, He, and I) irradiation are studied. In spite of the irradiation with different ion species and wide range of energies, the changes in magnetization are dominated by solely a single parameter; the density of energy which is deposited through elastic collision between the ions and the samples. For the low deposition energy density, the magnetization increases with increasing the deposition energy density, while the lattice structure remains unchanged. When the deposition energy density becomes larger, however, the magnetization decreases after reaching the maximum value. The decrease in the magnetization accompanies the crystal structure change from B2 to A1. The present results imply that the magnetic state of FeRh films can be designedly controlled by the energetic ion irradiations.

  19. Ion irradiation of carbonaceous chondrites as a simulation of space weathering on C-complex asteroids

    NASA Astrophysics Data System (ADS)

    Lantz, C.; Brunetto, R.; Barucci, M. A.; Bachelet, C.; Baklouti, D.; Bourçois, J.; Dartois, E.; Duprat, J.; Duret, P.; Engrand, C.; Godard, M.; Ledu, D.; Mivumbi, O.; Fornasier, S.

    2015-10-01

    We are investigating the effects of space weathering on primitive asteroids using ion irradiation on their meteoritic analogs. To do so, we exposed several carbonaceous chondrites (CV Allende, COs Lancé and Frontier Mountain 95002, CM Mighei, CI Alais, and ungrouped Tagish Lake) to 40 keV He+ ions as a simulation of solar wind irradiation using fluences up to 6.1016 ions/cm2 (implantation platform IRMA at CSNSM Orsay). As a test for our new experimental setup, we also studied samples of olivine and diopside. We confirm the reddening and darkening trends on S-type objects, but carbonaceous chondrites present a continuum of behaviors after ion irradiation as a function of the initial albedo and carbon content: from red to blue and from dark to bright.

  20. Effect of ion irradiation on nanoscale TiS2 systems with suppressed Titania phase

    NASA Astrophysics Data System (ADS)

    Hazarika, Saurabh J.; Mohanta, Dambarudhar; Tripathi, A.; Kanjilal, D.

    2016-10-01

    Titanium disulfide (TiS2), being an important of the transition metal dichalcogenide, (TMDC) family, has drawn numerous interest owing to exhibition of tunable band gap as well as high carrier mobility. In this work, we highlight preparation of TiS2 nanopowder with minimal TiO2 content and also demonstrate modified properties upon swift heavy ion irradiation on TiS2 nanoparticles dispersed PVA films. Different properties of the irradiated samples have been characterized through diffraction, microscopic and spectroscopic techniques. As a result of irradiation, due to agglomeration of particles, the grain size is found to increase. We could also observe a red shift after irradiation with increasing fluence, leading to easy flow of electron from valence to conduction band, which shows that conduction of electrons is more in case of irradiated films compared to the pristine one and thus there may be a possibility of using the irradiated samples in various optoelectronic devices.

  1. Effect of irradiation parameters on defect aggregation during thermal annealing of LiF irradiated with swift ions and electrons

    SciTech Connect

    Schwartz, K.; Neumann, R.; Trautmann, C.; Volkov, A. E.; Sorokin, M. V.

    2010-10-01

    Absorption spectroscopy were performed to study the effects of thermal annealing on the aggregation of color centers in LiF crystals irradiated with different ions between carbon and uranium of megaelectron volt-gigaelectron volt energy. The beam parameters such as energy, energy loss, and fluence have a pronounced influence on the initial defect composition and concentration as well as their evolution upon thermal annealing. A distinct phenomenon was observed, viz., the enhancement of F{sub n} centers for annealing temperatures between 500 and 700 K, followed by Li colloid formation above 700 K. The phenomenon requires specific irradiation conditions whereas the formation of Mg colloids from Mg impurities occurs in all irradiated crystals. The mechanisms of annealing and colloid formation are discussed.

  2. Luminescence imaging of water during carbon-ion irradiation for range estimation

    SciTech Connect

    Yamamoto, Seiichi Komori, Masataka; Koyama, Shuji; Morishita, Yuki; Sekihara, Eri; Akagi, Takashi; Yamashita, Tomohiro; Toshito, Toshiyuki

    2016-05-15

    Purpose: The authors previously reported successful luminescence imaging of water during proton irradiation and its application to range estimation. However, since the feasibility of this approach for carbon-ion irradiation remained unclear, the authors conducted luminescence imaging during carbon-ion irradiation and estimated the ranges. Methods: The authors placed a pure-water phantom on the patient couch of a carbon-ion therapy system and measured the luminescence images with a high-sensitivity, cooled charge-coupled device camera during carbon-ion irradiation. The authors also carried out imaging of three types of phantoms (tap-water, an acrylic block, and a plastic scintillator) and compared their intensities and distributions with those of a phantom containing pure-water. Results: The luminescence images of pure-water phantoms during carbon-ion irradiation showed clear Bragg peaks, and the measured carbon-ion ranges from the images were almost the same as those obtained by simulation. The image of the tap-water phantom showed almost the same distribution as that of the pure-water phantom. The acrylic block phantom’s luminescence image produced seven times higher luminescence and had a 13% shorter range than that of the water phantoms; the range with the acrylic phantom generally matched the calculated value. The plastic scintillator showed ∼15 000 times higher light than that of water. Conclusions: Luminescence imaging during carbon-ion irradiation of water is not only possible but also a promising method for range estimation in carbon-ion therapy.

  3. Time of flight-secondary ion mass spectrometry analysis of protein adsorption on a polyvinylidene difluoride surface modified by ion irradiation.

    PubMed

    Okuji, Shigeto; Kitazawa, Hideaki; Takeda, Yoshihiko

    2016-12-01

    We investigated the effects of nanoscopic surface modification of polyvinylidene difluoride (PVDF) and low-density polyethylene (LDPE) by plasma-based ion implantation on protein adsorption with time of flight-secondary ion mass spectrometry (ToF-SIMS) analysis. The chemical composition of the LDPE and PVDF surfaces was changed by ion irradiation. In particular, irradiation substantially decreased the number of CH and CF bonds on the PVDF surface, but only slightly decreased that of CH bonds for LDPE. These decreases may reflect a higher hydrogen recombination rate of the LDPE than the PVDF surface. An increase in oxygen was observed on both the LDPE and PVDF surfaces following ion irradiation, but was saturated after irradiation of 1×10(15)cm(-2) on the PVDF surface. The hydrophilicity of the ion-irradiated LDPE surface was promoted with an increase of the total ion fluence. Ion irradiation also changed the surface properties of PVDF to become more hydrophilic, but the variation did not correlate with the total ion fluence presumably due to the presence of fluorine atoms and the saturation of oxidation. Both bovine serum albumin (BSA) and collagen adsorption were suppressed on the LDPE surface by ion irradiation, which may have resulted from a decrease of the hydrophobic interaction. By contrast, ion irradiation increased protein adsorption on the PVDF surface, and BSA was adsorbed more than collagen, whereas there was no difference in the adsorption between BSA and collagen on the ion-irradiated LDPE surface. Moreover, the adsorption of BSA decreased on the oxygen- and fluorine-rich PVDF surface. These results indicate that the nanoscopic composition changes on the PVDF surface affect the adsorption behavior of BSA. Specifically, ferroelectric property on the PVDF surface was changed by ion irradiation and the nanoscopic change in polarity presumably affected the protein adsorption. Our findings suggest that selective adsorption control of protein can be

  4. Microdosimetric Monte-Carlo Simulations and Measurements of Heavy Ion Irradiation of a TEPC

    NASA Astrophysics Data System (ADS)

    Rollet, S.; Beck, P.; Bock, F.; Ferrari, A.; Latocha, M.; Uchihori, Y.; Wind, M.

    Microdosimetric methods are well suited for systematic study and quantification of the absorbed energy spatial and temporal distribution in irradiated matter A standard instrument used to measure the energy dissipated in microscopic sites by individual ionizing events is the Tissue Equivalent Proportional Counter TEPC The main focus of this work is to examine interactions of heavy ions with tissue using both experimental and numerical methods Measurements with a TEPC instrument were carried out recently in heavy ion radiation fields at the Heavy Ion Medical Accelerator HIMAC facility in Chiba which belongs to the National Institute of Radiological Sciences NIRS in Japan The instrument has been exposed to two kinds of heavy ions under different irradiation geometries and beam parameters The heavy ions used were Oxygen with energy of 400 MeV u and Iron of 300 MeV u For the simulation of the irradiation experiments two Monte Carlo codes are used namely FLUKA and GEANT4 Both codes are widely used for basic research and applications in radiation protection and dosimetry radiobiology radiotherapy and space Besides scoring average quantities both Monte Carlo codes have the capability to score energy deposition on an event by event basis Thus together with the total energy deposition a simulation of microdosimetric spectra is possible The comparison of measured and simulated lineal energy distribution show a satisfactory agreement both for irradiation with Oxygen ions of 400 MeV u and for Iron ions of 300 MeV u We will discuss in detail the

  5. A NRA study of temperature and heavy ion irradiation effects on helium migration in sintered uranium dioxide

    NASA Astrophysics Data System (ADS)

    Martin, G.; Garcia, P.; Labrim, H.; Sauvage, T.; Carlot, G.; Desgardin, P.; Barthe, M. F.; Piron, J. P.

    2006-10-01

    Helium implanted uranium dioxide sintered samples were studied using nuclear reaction analysis prior to and following heavy ion irradiations and temperature anneals at 800 °C and 1100 °C. The results show that the heavy ion irradiations do not produce measurable long range movement of helium atoms. However, the ion irradiations do affect the behaviour of helium during subsequent temperature anneals. As regards the 800 °C anneal, the reduced mobility of helium in the ion-irradiated samples is interpreted as resulting from enhanced helium atom segregation produced by the ion-irradiation. Conversely at 1100 °C, the initial heavy ion irradiation appears to produce a greater than expected movement of helium within the bulk of the sample which could be an indication of defect assisted helium diffusion. Thermal diffusion coefficients are also reported at 800 °C and 1100 °C based on an analysis using a one-dimensional diffusion model.

  6. Defect induced modification of structural, topographical and magnetic properties of zinc ferrite thin films by swift heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Raghavan, Lisha; Joy, P. A.; Vijaykumar, B. Varma; Ramanujan, R. V.; Anantharaman, M. R.

    2017-04-01

    Swift heavy ion irradiation provides unique ways to modify physical and chemical properties of materials. In ferrites, the magnetic properties can change significantly as a result of swift heavy ion irradiation. Zinc ferrite is an antiferromagnet with a Neel temperature of 10 K and exhibits anomalous magnetic properties in the nano regime. Ion irradiation can cause amorphisation of zinc ferrite thin films; thus the role of crystallinity on magnetic properties can be examined. The influence of surface topography in these thin films can also be studied. Zinc ferrite thin films, of thickness 320 nm, prepared by RF sputtering were irradiated with 100 MeV Ag ions. Structural characterization showed amorphisation and subsequent reduction in particle size. The change in magnetic properties due to irradiation was correlated with structural and topographical effects of ion irradiation. A rough estimation of ion track radius is done from the magnetic studies.

  7. A mechanistic model for depth-dependent hardness of ion irradiated metals

    NASA Astrophysics Data System (ADS)

    Xiao, Xiazi; Chen, Qianying; Yang, Hui; Duan, Huiling; Qu, Jianmin

    2017-03-01

    A mechanistic model was developed for modeling the depth-dependent hardness in ion irradiated metallic materials. The model is capable of capturing the indentation size effect, ion irradiation induced damage gradient effect, and effect of unirradiated region acting as a soft substrate. A procedure was developed and described in detail to parametrize the model based on experimentally obtained hardness vs. indentation depth curves. Very good agreement was observed between our model predictions and experimental data of several different stainless steels subjected to various ion irradiation conditions. In addition, two hardening mechanisms are revealed in the new model. One is the well-known indentation size effect arising from the creation of geometrically necessary dislocations as the indenter pierces into the materials. The other is the irradiation hardening due to the presence of irradiation-induced defects. As a function of indentation depth h, the hardening due to indentation size effect is described by hbar∗ / h , while the hardening due to irradiation first follows a power law form Phn , then changes to Z / h - Q /h3 , where hbar∗ , P, n, Z and Q > 0 are constants. This transition occurs at the indentation depth when the plastic zone reaches the end of the irradiated layer.

  8. Control of cell behavior on PTFE surface using ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Kitamura, Akane; Kobayashi, Tomohiro; Meguro, Takashi; Suzuki, Akihiro; Terai, Takayuki

    2009-05-01

    A polytetrafluoroethylene (PTFE) surface is smooth and biologically inert, so that cells cannot attach to it. Ion beam irradiation of the PTFE surface forms micropores and a melted layer, and the surface is finally covered with a large number of small protrusions. Recently, we found that cells could adhere to this irradiated PTFE surface and spread over the surface. Because of their peculiar attachment behavior, these surfaces can be used as biological tools. However, the factors regulating cell adhesion are still unclear, although some new functional groups formed by irradiation seem to contribute to this adhesion. To control cell behavior on PTFE surfaces, we must determine the effects of the outermost irradiated surface on cell adhesion. In this study, we removed the thin melted surface layer by postirradiation annealing and investigated cell behavior on the surface. On the surface irradiated with 3 × 1016 ions/cm2, cells spread only on the remaining parts of the melted layer. From these results, it is clear that the melted layer had a capacity for cell attachment. When the surface covered with protrusions was irradiated with a fluence of 1 × 1017 ions/cm2, the distribution of cells changed after the annealing process from 'sheet shaped' into multicellular aggregates with diameters of around 50 μm. These results indicate that we can control cell behavior on PTFE surfaces covered with protrusions using irradiation and subsequent annealing. Multicellular spheroids can be fabricated for tissue engineering using this surface.

  9. Physical and biological properties of the ion beam irradiated PMMA-based composite films

    NASA Astrophysics Data System (ADS)

    Shanthini, G. M.; Martin, Catherine Ann; Sakthivel, N.; Veerla, Sarath Chandra; Elayaraja, K.; Lakshmi, B. S.; Asokan, K.; Kanjilal, D.; Kalkura, S. Narayana

    2015-02-01

    Polymethyl methacrylate (PMMA) and PMMA-hydroxyapatite (PMMA-HAp) composite films, prepared by the solvent evaporation method were irradiated with 100 MeV Si7+ ions. Crystallographic, morphological and the functional groups of the pristine and irradiated samples were studied using glancing incident X-ray diffraction (GIXRD), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR) respectively. SEM reveals the creation of pores, along with an increase in porosity and cluster size on irradiation. Decrease in crystalline nature and crystallite size with an increase in ion fluence was observed from GIXRD patterns. The surface roughness and the wettability of the material were also enhanced, which could favour the cell-material interaction. The irradiated samples adsorbed significantly greater amount of proteins than pristine. Also, irradiation does not produce any toxic byproducts or leachants, and maintains the viability of 3T3 cells. The response of the irradiated samples towards biomedical applications was demonstrated by the improved antimicrobial activity, haemocompatibility and cytocompatibility. Swift heavy ion irradiation (SHI) could be an effective tool to modify and engineer the surface properties of the polymers to enhance the biocompatibility.

  10. Ion-irradiation-induced microstructural modifications in ferritic/martensitic steel T91

    NASA Astrophysics Data System (ADS)

    Liu, Xiang; Miao, Yinbin; Li, Meimei; Kirk, Marquis A.; Maloy, Stuart A.; Stubbins, James F.

    2017-07-01

    In this paper, in situ transmission electron microscopy investigations were carried out to study the microstructural evolution of ferritic/martensitic steel T91 under 1 MeV Krypton ion irradiation up to 4.2 × 1015 ions/cm2 at 573 K, 673 K, and 773 K. At 573 K, grown-in defects are strongly modified by black-dot loops, and dislocation networks together with black-dot loops were observed after irradiation. At 673 K and 773 K, grown-in defects are only partially modified by dislocation loops; isolated loops and dislocation segments were commonly found after irradiation. Post irradiation examination indicates that at 4.2 × 1015 ions/cm2, about 51% of the loops were a0 / 2 < 111 > type for the 673 K irradiation, and the dominant loop type was a0 < 100 > for the 773 K irradiation. Finally, a dispersed barrier hardening model was employed to estimate the change in yield strength, and the calculated ion data were found to follow the similar trend as the existing neutron data with an offset of 100-150 MPa.

  11. Enhanced electron field emission from carbon nanotubes irradiated by energetic C ions.

    PubMed

    Sun, Peng-Cheng; Deng, Jian-Hua; Cheng, Guo-An; Zheng, Rui-Ting; Ping, Zhao-Xia

    2012-08-01

    The field emission performance and structure of the vertically aligned multi-walled carbon nanotube arrays irradiated by energetic C ion with average energy of 40 keV have been investigated. During energetic C ion irradiation, the curves of emission current density versus the applied field of samples shift firstly to low applied fields when the irradiation doses are less than 9.6 x 10(16) cm(-2), and further increase of dose makes the curves reversing to a high applied field, which shows that high dose irradiation in carbon nanotube arrays makes their field emission performance worse. After energetic ion irradiation with a dose of 9.6 x 1016 cm(-2), the turn-on electric field and the threshold electric field of samples decreased from 0.80 and 1.13 V/microm to 0.67 and 0.98 V/microm respectively. Structural analysis of scanning electron microscopy, transmission electron microscopy and Raman spectroscopy indicates that the amorphous carbon nanowire/carbon nanotube hetero nano-structures have been fabricated in the C ion irradiated carbon nanotubes. The enhancement of electron field emission is due to the formation of amorphous carbon nanowires at the tip of carbon nanotube arrays, which is an electron emitting material with low work function.

  12. The loss of boron in ultra-shallow boron implanted Si under heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Pelicon, P.; El Bouanani, M.; Prasad, G. V. R.; Razpet, A.; Simcic, J.; Guo, B. N.; Birt, D.; Duggan, J. L.; McDaniel, F. D.

    2006-08-01

    Heavy ion impact has been known to cause a loss of light elements from the near-surface region of the irradiated sample. One of the possible approaches to a better understanding of the processes responsible for the release of specific elements is to irradiate shallow-implanted samples, which exhibit a well-known depth distribution of the implanted species. In this work, the samples studied were produced by implantation of Si wafers with 11 B at implantation energies of 250 and 500 eV and fluence of 1.0x10(15) atoms/cm 2 . Elastic Recoil Detection Analysis was applied to monitor the remnant boron fluence in the sample. Irradiation of the samples by a 14.2 (MeVF4+)-F-19 beam resulted in a slow decrease of boron remnant fluence with initial loss rates of the order of 0.05 B atom per impact ion. Under irradiation with 12 (MeVS3+)-S-32 ions, the remnant boron fluence in Si decreased exponentially with a much faster loss rate of boron and became constant after a certain heavy ion irradiation dose. A simple model, which assumes a finite desorption range and corresponding depletion of the near-surface region, was used to describe the observations. The depletion depths under the given irradiation conditions were calculated from the measured data.

  13. Damages in ceramics for nuclear waste transmutation by irradiation with swift heavy ions

    NASA Astrophysics Data System (ADS)

    Beauvy, Michel; Dalmasso, Chrystelle; Thiriet-Dodane, Catherine; Simeone, David; Gosset, Dominique

    2006-01-01

    Inert matrices are proposed for advanced nuclear fuels or for the transmutation of the actinides that is an effective solution for the nuclear waste management. The behaviour of inert matrix ceramics like MgO, MgAl2O4 and cubic ZrO2 oxides under irradiation is presented in this study. The alumina Al2O3 has been also studied as a reference for the ceramic materials. These oxides have been irradiated with swift heavy ions at CIRIL/GANIL to simulate the fragment fission effects. The irradiations with the different heavy ions (from S to Pb) with energy between 91 and 820 MeV, have been realised at room temperature or 500 °C. The fluencies were between 5 × 1010 and 5 × 1015 ions/cm2. The polished faces of sintered polycrystalline disks or single crystal slices have been characterized before and after irradiation by X-ray diffraction and optical spectroscopy. The apparent swelling evaluated from surface profile measurements after irradiation is very important for spinel and zirconia, comparatively with those of magnesia or alumina. The amorphisation seems to be at the origin of this swelling, and the electronic stopping power of the ions is the most influent parameter for the irradiation damages. The point defects characterized by optical spectroscopy show a significant amount of damage on the oxygen sub-lattice in the irradiated oxides. F+ centres are present in all irradiated oxides. However, new absorption bands are observed and cation clusters cannot be excluded in magnesia and spinel after irradiation.

  14. Effects of Ion Irradiation on Seedlings Growth Monitored by Ultraweak Delayed Luminescence.

    PubMed

    Grasso, Rosaria; Abe, Tomoko; Cirrone, Giuseppe A P; Cuttone, Giacomo; Gulino, Marisa; Musumeci, Francesco; Romano, Francesco; Ryuto, Hiromichi; Scordino, Agata

    2016-01-01

    The optical technique based on the measurement of delayed luminescence emitted from the biological samples has demonstrated its ability to provide valid and predictive information on the functional status of various biological systems. We want to extend this technique to study the effect of ionizing radiation on biological systems. In particular we are interested in the action of ion beams, used for therapeutic purposes or to increase the biological diversity. In general, the assessment of the damage that radiation produces both in the target objects and in the surrounding tissues, requires considerable time because is based on biochemical analysis or on the examination of the evolution of the irradiated systems. The delayed luminescence technique could help to simplify this investigation. We have so started our studies performing irradiations of some relatively simple vegetable models. In this paper we report results obtained from mung bean (Vigna radiata) seeds submitted to a 12C ion beam at the energy of 62 MeV/nucleon. The dry seeds were irradiated at doses from 50 to 7000 Gy. The photoinduced delayed luminescence of each seed before and after ion irradiation was measured. The growth of seedlings after irradiation was compared with that of untreated seeds. A growth reduction on increasing the dose was registered. The results show strong correlations between the ion irradiation dose, seeds growth and delayed luminescence intensity. In particular, the delayed luminescence intensity is correlated by a logistic function to the seedlings elongation and, after performing a suitable measurement campaign based on blind tests, it could become a tool able to predict the growth of seeds after ion irradiation. Moreover these results demonstrate that measurements of delayed luminescence could be used as a fast and non-invasive technique to check the effects of ion beams on relatively simple biological systems.

  15. Morphological and biochemical responses of Oryza sativa L. (cultivar MR219) to ion beam irradiation*

    PubMed Central

    Ling, Anna Pick Kiong; Ung, Ying Chian; Hussein, Sobri; Harun, Abdul Rahim; Tanaka, Atsushi; Yoshihiro, Hase

    2013-01-01

    Objective: Heavy ion beam, which has emerged as a new mutagen in the mutation breeding of crops and ornamental plants, is expected to result in the induction of novel mutations. This study investigates the morphological and biochemical responses of Oryza sativa toward different doses of carbon ion beam irradiation. Methods: In this study, the dry seeds of O. sativa were irradiated at 0, 20, 40, 60, 80, 100, and 120 Gy, followed by in-vitro germination under controlled conditions. Morphological and biochemical studies were conducted to investigate the morphological and physiological responses of O. sativa towards ion beam irradiation. Results: The study demonstrated that low doses (10 Gy) of ion beam have a stimulating effect on the height, root length, and fresh weight of the plantlets but not on the number of leaves. Meanwhile, doses higher than 10 Gy caused reductions in all the morphological parameters studied as compared to the control samples. The highest total soluble protein content [(2.11±0.47) mg/g FW] was observed in plantlets irradiated at 20 Gy. All irradiated plantlets were found to have 0.85% to 58.32% higher specific activity of peroxidase as compared to the control samples. The present study also revealed that low doses of ion beam (10 and 20 Gy) had negligible effect on the total chlorophyll content of O. sativa plantlets while 40 Gy had a stimulating effect on the chlorophyll content. Plantlets irradiated between 40 to 120 Gy were shown to be 0.38% to 9.98% higher in total soluble nitrogen content which, however, was not significantly different from the control samples. Conclusions: Carbon ion beam irradiation administered at low to moderate doses of 10 to 40 Gy may induce O. sativa mutants with superior characteristics. PMID:24302713

  16. Effects of Ion Irradiation on Seedlings Growth Monitored by Ultraweak Delayed Luminescence

    PubMed Central

    Abe, Tomoko; Cirrone, Giuseppe A. P.; Cuttone, Giacomo; Gulino, Marisa; Musumeci, Francesco; Romano, Francesco; Ryuto, Hiromichi; Scordino, Agata

    2016-01-01

    The optical technique based on the measurement of delayed luminescence emitted from the biological samples has demonstrated its ability to provide valid and predictive information on the functional status of various biological systems. We want to extend this technique to study the effect of ionizing radiation on biological systems. In particular we are interested in the action of ion beams, used for therapeutic purposes or to increase the biological diversity. In general, the assessment of the damage that radiation produces both in the target objects and in the surrounding tissues, requires considerable time because is based on biochemical analysis or on the examination of the evolution of the irradiated systems. The delayed luminescence technique could help to simplify this investigation. We have so started our studies performing irradiations of some relatively simple vegetable models. In this paper we report results obtained from mung bean (Vigna radiata) seeds submitted to a 12C ion beam at the energy of 62 MeV/nucleon. The dry seeds were irradiated at doses from 50 to 7000 Gy. The photoinduced delayed luminescence of each seed before and after ion irradiation was measured. The growth of seedlings after irradiation was compared with that of untreated seeds. A growth reduction on increasing the dose was registered. The results show strong correlations between the ion irradiation dose, seeds growth and delayed luminescence intensity. In particular, the delayed luminescence intensity is correlated by a logistic function to the seedlings elongation and, after performing a suitable measurement campaign based on blind tests, it could become a tool able to predict the growth of seeds after ion irradiation. Moreover these results demonstrate that measurements of delayed luminescence could be used as a fast and non-invasive technique to check the effects of ion beams on relatively simple biological systems. PMID:27936220

  17. Influence of irradiation spectrum and implanted ions on the amorphization of ceramics

    SciTech Connect

    Zinkle, S.J.; Snead, L.L.

    1996-04-01

    Amorphization cannot be tolerated in ceramics proposed for fusion energy applications due to the accompanying large volume change ({approx} 15% in SiC) and loss of strength. Ion beam irradiations at temperatures between 200 K and 450 K were used to examine the likelihood of amorphization in ceramics being considered for the structure (SiC) and numerous diagnostic and plasma heating systems (MgAl{sub 2}O{sub 4}, Al{sub 2}O{sub 3}, MgO, Si{sub 3}N{sub 4}) in fusion energy systems. The microstructures were examined following irradiation using cross-section transmission electron microscopy. The materials in this study included ceramics with predominantly covalent bonding (SiC, Si{sub 3}N{sub 4}) and predominantely ionic bonding (MgAl{sub 2}O{sub 4}, Al{sub 2}O{sub 3}, MgO). The samples were irradiated with a variety of ion beams (including some simultaneous dual ion beam irradiations) in order to investigate possible irradiation spectrum effects. The ion energies were >0.5 MeV in all cases, so that the displacement damage effects could be examined in regions well separated from the implanted ion region.

  18. Effect of oxygen ion irradiation on dielectric, structural, chemical and thermoluminescence properties of natural muscovite mica.

    PubMed

    Kaur, Sukhnandan; Singh, Surinder; Singh, Lakhwant

    2017-03-01

    Thin cleaved samples (~18µm) of natural muscovite mica were irradiated with 80MeV oxygen ion beam at fluence ranging from 1×10(12) to 5×10(13)ion/cm(2). The alterations in dielectric, structural, chemical and thermoluminescence properties of irradiated as well as pristine samples have been investigated. Dielectric constant decreases while other dielectric parameters such as dielectric loss, tanδ, ac conductivity, real and imaginary parts of electric modulus increase with increase of ion fluence. Williamson Hall investigation has been utilized to ascertain crystallite size and micro strain of pristine and irradiated samples. The XRD analysis revealed a significant increase in micro strain and dislocation density with an increase of ion fluence. The variations in dielectric properties upon irradiation are collaborated with structural modifications in the muscovite. No appreciable changes in characteristic bands (FTIR) have been observed after irradiation, indicating that natural muscovite mica is chemically stable. Natural muscovite mica has eminent applications in heavy ions dosimetry due to observation of well defined single peak at 303°C with activation energy of 1.24eV in TL spectrum.

  19. Swift heavy ion irradiation-induced enhancement in structural, conformational and electrical properties of polyaniline nanofibers

    NASA Astrophysics Data System (ADS)

    Hazarika, Jayanta; Nath, Chandrani; Kumar, A.

    2014-01-01

    We report here the irradiation effects of 160 MeV Ni12+ ion beam on the structural and electrical properties of polyaniline (PAni) nanofibers synthesized by the interfacial polymerization method. The morphological studies show an increase in average diameter of PAni nanofibers upon swift heavy ion (SHI) irradiation. X-ray diffraction results show the amorphous nature of PAni nanofibers and upon SHI irradiation its crystallinity (K) and average crystallite size or extent of order (L) increase with increasing ion fluence. Fourier transform infrared spectroscopy results confirm the formation of PAni and suggest better conjugation length of PAni chains with increasing ion fluence. The ac conductivity follows the universal power law, σac=A ωs with (0irradiation conductivity increases appreciably with fluence. The decreasing behavior of frequency exponent s with temperature suggests correlated barrier hopping transport of charge carriers. Current-voltage characteristics of PAni nanofibers show the non-ohmic behavior and the current increases with increasing ion fluence. Thermogravimetric analysis exhibits enhanced thermal stability of PAni nanofibers upon SHI irradiation.

  20. Optical and dielectric properties of ion beam irradiated Ag/polymethyl methacrylate nanocomposites.

    PubMed

    Gavade, Chaitali; Singh, N L; Khanna, P K

    2014-08-01

    Changes in the dielectric, optical, structural and thermal properties of PMMA/silver nanocomposites of different concentrations of silver nanoparticles (5%, 10%, 15%) due to swift heavy ion irradiation were studied by means of impedance gain phase analyzer, UV-visible spectroscopy, X-ray diffraction and differential scanning calorimetry. Samples were irradiated with 120 MeV Si-ions at fluences of 1 x 10(11), 1 x 10(12) ions/cm2. Dependence of dielectric properties on frequency, ion beam fluence and filler concentration was studied. The results revealed the enhancement in dielectric properties after dopping nanoparticles and also upon irradiation. Optical properties like band gap was estimated for pure polymer and nanocomposite films from their optical absorption spectra in the wavelength region 200-800 nm. It was found that the band gap value shifted to lower energy (from 4.58 eV to 3.21 eV) on doping with silver nanoparticles. Differential scanning calorimetry analysis revealed a decrease in the glass transition temperature upon irradiation, which may be attributed to scissioning of polymer chain due to ion beam irradiation which is also confirmed with XRD analysis.

  1. TiO2 films photocatalytic activity improvements by swift heavy ions irradiation

    NASA Astrophysics Data System (ADS)

    Rafik, Hazem; Mahmoud, Izerrouken; Mohamed, Trari; Abdenacer, Benyagoub

    2014-08-01

    TiO2 thin films synthesized by sol-gel on glass substrates are irradiated by 90 MeV Xe ions at various fluences and room temperature under normal incidence. The structural, electrical, optical and surface topography properties before and after Xe ions irradiation are investigated. X-ray diffraction (XRD) reveals that the crystallinity is gradually destroyed, and the films become amorphous above 5×1012 ions/cm2. The band gap is not affected by Xe ions irradiation as evidenced from the optical measurements. By contrast, the conductivity increases with raising Xe fluence. The energy band diagram established from the electrochemical characterization shows the feasibility of TiO2 films for the photo-electrochemical chromate reduction. Xe ion irradiation results in enhanced photocatalytic activity in aquatic medium, evaluated by the reduction of Cr(VI) into trivalent state. TiO2 films irradiated at 1013 Xe/cm2 exhibit the highest photoactivity; 69% of chromate (10 ppm) is reduced at pH 3 after 4 h of exposure to sunlight (1120 mW cm-2) with a quantum yield of 0.06%.

  2. Effect of Grazing Angle Cross-Ion Irradiation on Ag Thin Films

    NASA Astrophysics Data System (ADS)

    Kumar, Manish; Jangid, Teena; Panchal, Vandana; Kumar, Praveen; Pathak, Abhishek

    2016-10-01

    Apart from the spherical shape, control over other shapes is a technical challenge in synthesis approaches of nanostructures. Here, we studied the effect of grazing angle cross-irradiation Ag thin films for the nanostructures evolution from a top-down approach. Ag thin films of different thicknesses were deposited on Si (100) and glass substrates by electron beam evaporation system and subsequently irradiated at grazing angle ions by 80 keV Ar+ in two steps (to induce effectively a cross-ion irradiation). Pristine films exhibited dense and uniform distribution of Ag nanoparticles with their characteristic surface plasmon resonance-induced absorption peak around 420 nm. When the film surfaces were treated with cross-grazing angle irradiation of Ar ions with varying effective fluences from 0.5 × 1017 ions/cm2 to 2.0 × 1017 ions/cm2, it was found that fluence values governed the competition of sputtering and sputter re-deposition of Ag. As a result, lower irradiation fluence favoured the formation of cone-like nanostructures, whereas high fluence values demonstrated dominant sputtering. Fluence-dependent modification of surface features was studied through the Fourier transform infrared spectroscopy and the Rutherford backscattering spectroscopy. Theoretical justifications for the underlying mechanisms are presented to justify the experimental results.

  3. MeV Au Ion Irradiation in Silicon and Nanocrystalline Zirconia Film Deposited on Silicon Substrate

    SciTech Connect

    Chang, Yongqin; Zhang, Yanwen; Zhu, Zihua; Edmondson, Dr. Philip; Weber, William J

    2012-01-01

    Nanocrystalline zirconia (ZrO2) film with thickness of 305 nm deposited on a silicon substrate was irradiated with 2 MeV Au ions to different fluences at different temperatures. The implanted ion profiles were measured by time-of-flight secondary ion mass spectrometry (ToF-SIMS) and simulated using the stopping and range of ions in matter (SRIM) code, respectively. The experimental results show that a large fraction of the incident Au ions penetrates through the ZrO2 film and are deposited into the Si substrate. At the interface of ZrO2 and Si, a sudden decrease of Au concentration is observed due to the much larger scattering cross section of Au in ZrO2 than in Si. The depth profile of the Au ions is measured in both the ZrO2 films and the Si substrates, and the results show that the Au distribution profiles do not exhibit a dependence on irradiation temperature. The local Au concentration increases proportionally with the irradiation fluence, suggesting that no thermal or irradiation-induced redistribution of the implanted Au ions. However, the Au concentration in the ZrO2 films, as determined by SIMS, is considerably lower than that predicted by the SRIM results, and the penetration depth from the SIMS measurements is much deeper than that from the SRIM predictions. These observations can be explained by an overestimation of the electronic stopping power, used in the SRIM program, for heavy incident ions in light targets. Overestimation of the heavy-ion electronic stopping power may lead to errors in local dose calculation and underestimation of the projected range of slow heavy ions in targets that contain light elements. A quick estimate based on a reduced target density may be used to compensate the overestimation of the electronic stopping power in the SRIM program to provide better ion profile prediction.

  4. MeV Au Ion Irradiation in Silicon and Nanocrystalline Zirconia Film Deposited on Silicon Substrate

    SciTech Connect

    Chang, Yongqin; Zhang, Yanwen; Zhu, Zihua; Edmondson, Philip D.; Weber, William J.

    2012-09-01

    Nanocrystalline zirconia (ZrO2) film with thickness of 305 nm deposited on a silicon substrate was irradiated with 2 MeV Au ions to different fluences at different temperatures. The implanted ion profiles were measured by time-of-flight secondary ion mass spectrometry (ToF-SIMS) and simulated using the stopping and range of ions inmatter (SRIM) code, respectively. The experimental results show that a large fraction of the incident Au ions penetrates through the ZrO2 film and are deposited into the Si substrate. At the interface of ZrO2 and Si, a sudden decrease of Au concentration is observed due to the much larger scattering cross section of Au in ZrO2 than in Si. The depth profile of the Au ions is measured in both the ZrO2 films and the Si substrates, and the results show that the Au distribution profiles do not exhibit a dependence on irradiation temperature. The local Au concentration increases proportionally with the irradiation fluence, suggesting that no thermal or irradiation-induced redistribution of the implanted Au ions. However, the Au concentration in the ZrO2 films, as determined by SIMS, is considerably lower than that predicted by the SRIM results, and the penetration depth from the SIMS measurements is much deeper than that from the SRIM predictions. These observations can be explained by an overestimation of the electronic stopping power, used in the SRIM program, for heavy incident ions in light targets. Over-estimation of the heavy-ion electronic stopping power may lead to errors in local dose calculation and underestimation of the projected range of slow heavy ions in targets that contain light elements. A quick estimate based on a reduced target density may be used to compensate the overestimation of the electronic stopping power in the SRIM program to provide better ion profile prediction.

  5. A molecular dynamics analysis of ion irradiation of ultrathin amorphous carbon films

    NASA Astrophysics Data System (ADS)

    Qi, J.; Komvopoulos, K.

    2016-09-01

    Molecular dynamics (MD) simulations provide insight into nanoscale problems where continuum description breaks down, such as the modeling of ultrathin films. Amorphous carbon (a-C) films are commonly used as protective overcoats in various contemporary technologies, including microelectromechanical systems, bio-implantable devices, optical lenses, and hard-disk drives. In all of these technologies, the protective a-C film must be continuous and very thin. For example, to achieve high storage densities (e.g., on the order of 1 Tb/in.2) in magnetic recording, the thickness of the a-C film used to protect the magnetic media and the recording head against mechanical wear and corrosion must be 2-3 nm. Inert ion irradiation is an effective post-deposition method for reducing the film thickness, while preserving the mechanical and chemical characteristics. In this study, MD simulations of Ar+ ion irradiated a-C films were performed to elucidate the effects of the ion incidence angle and ion kinetic energy on the film thickness and structure. The MD results reveal that the film etching rate exhibits a strong dependence on the ion kinetic energy and ion incidence angle, with a maximum etching rate corresponding to an ion incidence angle of ˜20°. It is also shown that Ar+ ion irradiation mainly affects the structure of the upper half of the ultrathin a-C film and that carbon atom hybridization is a strong function of the ion kinetic energy and ion incidence angle. The results of this study elucidate the effects of important ion irradiation parameters on the structure and thickness of ultrathin films and provide fundamental insight into the physics of dry etching.

  6. Heavy ion irradiation induced dislocation loops in AREVA's M5® alloy

    NASA Astrophysics Data System (ADS)

    Hengstler-Eger, R. M.; Baldo, P.; Beck, L.; Dorner, J.; Ertl, K.; Hoffmann, P. B.; Hugenschmidt, C.; Kirk, M. A.; Petry, W.; Pikart, P.; Rempel, A.

    2012-04-01

    Pressurized water reactor (PWR) Zr-based alloy structural materials show creep and growth under neutron irradiation as a consequence of the irradiation induced microstructural changes in the alloy. A better scientific understanding of these microstructural processes can improve simulation programs for structural component deformation and simplify the development of advanced deformation resistant alloys. As in-pile irradiation leads to high material activation and requires long irradiation times, the objective of this work was to study whether ion irradiation is an applicable method to simulate typical PWR neutron damage in Zr-based alloys, with AREVA's M5® alloy as reference material. The irradiated specimens were studied by electron backscatter diffraction (EBSD), positron Doppler broadening spectroscopy (DBS) and in situ transmission electron microscopy (TEM) at different dose levels and temperatures. The irradiation induced microstructure consisted of - and -type dislocation loops with their characteristics corresponding to typical neutron damage in Zr-based alloys; it can thus be concluded that heavy ion irradiation under the chosen conditions is an excellent method to simulate PWR neutron damage.

  7. Response of nanostructured ferritic alloys to high-dose heavy ion irradiation

    SciTech Connect

    Parish, Chad M.; White, Ryan M.; LeBeau, James M.; Miller, Michael K.

    2014-02-01

    A latest-generation aberration-corrected scanning/transmission electron microscope (STEM) is used to study heavy-ion-irradiated nanostructured ferritic alloys (NFAs). Results are presented for STEM X-ray mapping of NFA 14YWT irradiated with 10 MeV Pt to 16 or 160 dpa at -100°C and 750°C, as well as pre-irradiation reference material. Irradiation at -100°C results in ballistic destruction of the beneficial microstructural features present in the pre-irradiated reference material, such as Ti-Y-O nanoclusters (NCs) and grain boundary (GB) segregation. Irradiation at 750°C retains these beneficial features, but indicates some coarsening of the NCs, diffusion of Al to the NCs, and a reduction of the Cr-W GB segregation (or solute excess) content. Ion irradiation combined with the latest-generation STEM hardware allows for rapid screening of fusion candidate materials and improved understanding of irradiation-induced microstructural changes in NFAs.

  8. Dynamical response of helium bubble motion to irradiation with high-energy self-ions in aluminum at high temperature.

    SciTech Connect

    Ono, K.; Miyamoto, M.; Arakawa, K.; Birtcher, R. C.; Materials Science Division; Shimane Univ.; Osaka Univ.

    2009-02-21

    Brownian-type motion of helium bubbles in aluminum and its dynamical response to irradiation with 100-keV Al{sup +} ions at high temperatures has been studied using in situ irradiation and transmission electron microscopy. It is found that, for most bubbles, the Brownian-type motion is retarded under irradiation, while the mobility returns when the irradiation is stopped. In contrast, under irradiation, a small number of bubbles display exceptionally rapid motion associated with the change in bubble size. These effects are discussed in terms of the dynamical interaction of helium bubbles with cascade damage formed by the high-energy self-ion irradiation.

  9. Effect of combined local variations in elastic and inelastic energy losses on the morphology of tracks in ion-irradiated materials

    SciTech Connect

    Jozwik Biala, Iwona; Jagielski, Jacek K.; Arey, Bruce W.; Kovarik, Libor; Sattonay, G.; Debelle, A.; Mylonas, S.; Monnet, I.; Thome, Lionel

    2013-07-13

    A judicious choice of irradiation parameters and experimental methodology allowed the visualization of the tracks created by swift heavy ions in pyrochlores over the entire ion trajectories. Several peculiarities were observed: a layered structure of tracks composed of an amorphous core surrounded by a strained crystalline envelope, a change of the track diameter as a function of the ion slowing down, a loss of parallelism of tracks, a transformation from continuous to discontinuous regime, and an increasing contribution of elastic collisions at large depths. These observations are compared to the respective amount of electronic and nuclear energy losses.

  10. Nanoscale η-NiSi formation via ion irradiation of Si/Ni/Si

    NASA Astrophysics Data System (ADS)

    Banu, Nasrin; Satpati, Biswarup; Bhukta, Anjan; Dev, B. N.

    2017-01-01

    Nickel monosilicide (NiSi) has emerged as an excellent material of choice for source-drain contact applications below 45 nm node complementary metal-oxide-semiconductor technology. We have investigated the formation of nanoscale NiSi by ion irradiation of Si (˜5 nm)/Ni(˜15 nm)/Si, grown in an ultrahigh vacuum environment. Irradiation was carried out at room temperature with 1 MeV Si+ ions. X-ray diffraction (XRD) and transmission electron microscopy (TEM) were employed for analysis. With increasing ion fluence, ion beam mixing occurs and more and more Si is incorporated into the Ni layer, and this layer gets amorphized. At an even higher fluence, a recrystallized uniform nickel monosilicide (η-NiSi) layer is formed. Several planar spacings of different Miller indices of η-NiSi have been observed in XRD and TEM. Additionally, an interesting amorphization and recrystallization behavior has been observed in the substrate Si with increasing ion fluence. To our knowledge, this has never been observed in ion irradiation of bare Si in decades of work in this area. This kind of amorphization/recrystallization in Si is apparently Ni-induced. Irradiation displaces Ni and produces a distribution of Ni in amorphized Si. Irradiation at a higher fluence produces two recrystallized Si bands in amorphous Si with concomitant accumulation of Ni at the amorphous/crystalline interfaces. On a further increase in irradiation fluence, the recrystallized Si bands again pass through amorphization and recrystallization. The total thickness of recrystallized, as well as amorphous Si, shows an oscillatory behavior as a function of ion fluence.

  11. Ultraviolet Spectral Changes in Amorphous Carbon Grains Induced by Ion Irradiation

    NASA Astrophysics Data System (ADS)

    Mennella, V.; Baratta, G. A.; Colangeli, L.; Palumbo, P.; Rotundi, A.; Bussoletti, E.; Strazzulla, G.

    1997-05-01

    Small carbon grains, processed by UV radiation and cosmic rays, have been proposed as carriers of the 217.5 nm bump present in the interstellar extinction curves (Hecht 1986; Sorrell 1990). In this paper, we present the results of an experiment aimed at simulating, in a first approximation, the cosmic-ray irradiation active in space. We have studied the effects induced by 3 keV He+ ions on the UV spectrum of small cosmic analog carbon grains. Two different kinds of grains have been analyzed. They were produced by vapor condensation in hydrogen and argon quenching atmospheres. Spectrophotometric measurements have been carried out on grains as they were produced and after ion irradiation in the spectral range 0.19-2 μm. Relevant UV spectral changes are observed after ion irradiation: while the UV absorption band shifts from 203 to 215 nm in hydrogenated amorphous carbon grains, an opposite trend is observed for the samples produced in the argon atmosphere. In this case the UV band moves from 240 to 218 nm. These spectral changes are well correlated with the optical gap variations and are therefore interpreted in terms of grain microstructure changes induced by the interactions with ions. At the highest ion fluence considered, the two carbons tend to have a similar microstructure, as testified by the UV peak position and optical gap values because of a saturation effect of the two competitive processes, amorphization and graphitization, which occur in carbon samples during ion irradiation (Compagnini & Calcagno 1996). The results of the present experiment suggest that hydrogenated amorphous carbon grains cannot be transformed into graphite grains by cosmic-ray irradiation. Moreover, the efficiency of ion irradiation in destroying well-ordered aromatic structures poses the problem of the survival itself of polycrystalline or pure graphite particles in the interstellar medium.

  12. Biodamage via shock waves initiated by irradiation with ions.

    PubMed

    Surdutovich, Eugene; Yakubovich, Alexander V; Solov'yov, Andrey V

    2013-01-01

    Radiation damage following the ionising radiation of tissue has different scenarios and mechanisms depending on the projectiles or radiation modality. We investigate the radiation damage effects due to shock waves produced by ions. We analyse the strength of the shock wave capable of directly producing DNA strand breaks and, depending on the ion's linear energy transfer, estimate the radius from the ion's path, within which DNA damage by the shock wave mechanism is dominant. At much smaller values of linear energy transfer, the shock waves turn out to be instrumental in propagating reactive species formed close to the ion's path to large distances, successfully competing with diffusion.

  13. Energy dependent ripple growth on Si (100) by N+ ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Bhowmik, D.; Karmakar, P.

    2017-05-01

    The energy dependence of pattern formation on Si (100) surface by N+ ion beam irradiation has been studied. Periodic ripple pattern growth has been found for low energy (5-10 keV) N+ ion bombardment at oblique incidence at a fluence of 7 × 1017 ions/cm2. The wave vector of the ripples is parallel to the ion beam direction which follows the Bradley Harper theory of ripple growth [Bradley et. al, J. Vac. Sci. Technol. A 6, 2390 (1988)]. We also found that the lateral (wavelength) and vertical (roughness) dimensions of the ripples increase with the ion energy. Ion penetration and collision cascade dimensions are calculated by Stopping and Range of Ions in Matter (SRIM). It is found that the roughness is proportional to ion penetration depth whereas the wavelength is proportional to the horizontal width of collision cascade.

  14. Detection of artificially created negative ion clouds with incoherent scatter radar

    NASA Technical Reports Server (NTRS)

    Sultan, Peter J.; Mendillo, Michael; Oliver, William L.; Holt, John M.

    1992-01-01

    The physical mechanisms by which negative ions change the shape of the incoherent scatter spectrum, and the way in which shape changes may be used to detect the presence of heavy positive and negative ions in an ambient ionosphere are investigated. In order to detect heavy negative ions, the temperature structure of the ionosphere is fixed to a prevent average measurement, and any changes in spectral shape during the experiment are interpreted as being caused by changes in composition, and not by changes in the temperature ratio Te/Ti. The spatial and temporal development of heavy negative ion plasma clouds created during four active chemical release experiments was observed. Concentrations of 10-40-percent SF6(-) were detected in SPINEX 1, SPINEX 2, and IMS data sets. An average uncertainty of +/-10-percent SF6(-) is present in all three experiments. Concentrations of 30-percent Br(-) were detected in the NICARE 1 release, with uncertainties of +/-4 percent.

  15. Comparison of gain degradation and deep level transient spectroscopy in pnp Si bipolar junction transistors irradiated with different ion species

    SciTech Connect

    Aguirre, B. A.; Bielejec, E.; Fleming, R. M.; Vizkelethy, G.; Vaandrager, B.; Campbell, J.; Martin, W. J.; King, D. B.

    2016-12-09

    Here, we studied the effect of light ion and heavy ion irradiations on pnp Si BJTs. A mismatch in DLTS deep peak amplitude for devices with same final gain but irradiated with different ion species was observed. Also, different ions cause different gain degradation when the DLTS spectra are matched. Pre-dosed ion-irradiated samples show that ion induced ionization does not account for the differences in DLTS peak height but isochronal annealing studies suggest that light ions produce more VP defects than heavy ions to compensate for the lack of clusters that heavy ions produce. The creation of defect clusters by heavy ions is evident by the higher content of E4 and V*2 defects compared to light ions.

  16. Comparison of gain degradation and deep level transient spectroscopy in pnp Si bipolar junction transistors irradiated with different ion species

    DOE PAGES

    Aguirre, B. A.; Bielejec, E.; Fleming, R. M.; ...

    2016-12-09

    Here, we studied the effect of light ion and heavy ion irradiations on pnp Si BJTs. A mismatch in DLTS deep peak amplitude for devices with same final gain but irradiated with different ion species was observed. Also, different ions cause different gain degradation when the DLTS spectra are matched. Pre-dosed ion-irradiated samples show that ion induced ionization does not account for the differences in DLTS peak height but isochronal annealing studies suggest that light ions produce more VP defects than heavy ions to compensate for the lack of clusters that heavy ions produce. The creation of defect clusters bymore » heavy ions is evident by the higher content of E4 and V*2 defects compared to light ions.« less

  17. Characterization of biodegradable polymers irradiated with swift heavy ions

    NASA Astrophysics Data System (ADS)

    Salguero, N. G.; del Grosso, M. F.; Durán, H.; Peruzzo, P. J.; Amalvy, J. I.; Arbeitman, C. R.; García Bermúdez, G.

    2012-02-01

    In view of their application as biomaterials, there is an increasing interest in developing new methods to induce controlled cell adhesion onto polymeric materials. The critical step in all these methods involves the modification of polymer surfaces, to induce cell adhesion, without changing theirs degradation and biocompatibility properties. In this work two biodegradable polymers, polyhydroxybutyrate (PHB) and poly- L-lactide acid (PLLA) were irradiated using carbon and sulfur beams with different energies and fluences. Pristine and irradiated samples were degradated by immersion in a phosphate buffer at pH 7.0 and then characterized. The analysis after irradiation and degradation showed a decrease in the contact angle values and changes in their crystallinity properties.

  18. Ion beam damage assessment and waveguide formation induced by energetic Si-ion irradiation in lanthanum aluminate crystal

    NASA Astrophysics Data System (ADS)

    Liu, Y.; Huang, Q.; Crespillo, M. L.; Qiao, M.; Liu, P.; Wang, X. L.

    2017-02-01

    Lanthanum aluminate (LaAlO3) crystal has emerged as one of the most valuable functional-materials, and its physical, electronic and optical properties strongly depend on the crystal structure, which can be easily altered in an irradiation environment and therefore affect the performance of LaAlO3-based devices. On the other hand, the preparation of LaAlO3 waveguide is also a scientific challenge for its potential application prospects in optoelectronics field. In this work, the damage evolution behavior of LaAlO3 crystal under Si-ion irradiation has been discussed in detail utilizing complementary characterization techniques, and then, single-mode waveguide of LaAlO3 crystal in the visible band can be obtained based on ion-irradiation-induced lattice damage behavior. Waveguide optical-coupling techniques are used to show its competitive features. Thus, novel optical waveguides with optimized features in LaAlO3 crystals can be tailored by a proper selection of ion mass, energy and fluence using the modification of the target material during ion irradiation process.

  19. Molecular dynamics and dynamic Monte-Carlo simulation of irradiation damage with focused ion beams

    NASA Astrophysics Data System (ADS)

    Ohya, Kaoru

    2017-03-01

    The focused ion beam (FIB) has become an important tool for micro- and nanostructuring of samples such as milling, deposition and imaging. However, this leads to damage of the surface on the nanometer scale from implanted projectile ions and recoiled material atoms. It is therefore important to investigate each kind of damage quantitatively. We present a dynamic Monte-Carlo (MC) simulation code to simulate the morphological and compositional changes of a multilayered sample under ion irradiation and a molecular dynamics (MD) simulation code to simulate dose-dependent changes in the backscattering-ion (BSI)/secondary-electron (SE) yields of a crystalline sample. Recent progress in the codes for research to simulate the surface morphology and Mo/Si layers intermixing in an EUV lithography mask irradiated with FIBs, and the crystalline orientation effect on BSI and SE yields relating to the channeling contrast in scanning ion microscopes, is also presented.

  20. Corrosion behavior of Ni/sup +/-ion irradiated NiTi alloys

    SciTech Connect

    Wang, R.; Brimhall, J.L.

    1983-11-01

    Corrosion behavior of Ni/sup +/-irradiated NiTi alloys was studied in chloride solutions, together with unirradiated NiTi material with different surface conditions. Ion irradiation with either 2.5 or 5 MeV Ni/sup +/ ions transformed the NiTi surface into an amorphous layer up to 1.5 micrometers thick. Studies of corrosion potential vs time and polarization behavior indicated a small enhancement of the passivation for the Ni/sup +/-irradiated NiTi over the unirradiated NiTi. The unirradiated NiTi with a mechanically polished, course surface was susceptible to pitting and crevice corrosion attack in 1 N HCl solution. The homogeneous amorphous structure in the irradiated alloy retarded this type of localized corrosion.

  1. Ion irradiation-induced diffusion in bixbyite-fluorite related oxides: Dislocations and phase transformation

    NASA Astrophysics Data System (ADS)

    Rolly, Gaboriaud; Fabien, Paumier; Bertrand, Lacroix

    2014-05-01

    Ion-irradiation induced diffusion and the phase transformation of a bixbyite-fluorite related rare earth oxide thin films are studied. This work is focused on yttrium sesquioxide, Y2O3, thin films deposited on Si (1 0 0) substrates using the ion beam sputtering technique (IBS). As-deposited samples were annealed ant then irradiated at cryogenic temperature (80 K) with 260 keV Xe2+ at different fluences. The irradiated thin oxide films are characterized by X-ray diffraction. A cubic to monoclinic phase transformation was observed. Analysis of this phenomenon is done in terms of residual stresses. Stress measurements as a function of irradiation fluences were realised using the XRD-sin2ψ method. Stress evolution and kinetic of the phase transformation are compared and leads to the role-played by the nucleation of point and extended defects.

  2. Mechanical response to swift ion irradiation-induced nano-tracks in silica

    NASA Astrophysics Data System (ADS)

    Páramo, Ángel R.; Sordo, F.; Garoz, D.; Peña-Rodríguez, O.; Prada, A.; Olivares, J.; Crespillo, M. L.; Perlado, J. M.; Rivera, A.

    2015-06-01

    Ion irradiation on dielectric materials produces several processes, such ionization and defect formation followed by a decay governed by thermal processes such as heat diffusion and atomic rearrangement. Finally in the irradiated region the mechanical properties are altered, strain and stress fields appear, a densification takes places and other properties such as the refractive index are affected. In order to simulate the mechanical response of silica to swift ion irradiation we use a methodology based on molecular dynamics (MD) and finite element methods (FEM). We use information from MD to obtain the local densification generated by an incoming swift ion. Finally we calculate the densification in the ion track using FEM. This method provides information on the strain and stress field along the material as a function of ion irradiation fluence. For this work an experimental campaign using Br ions from 5 to 50 MeV has been done at CMAM accelerator (Madrid). We measured the refractive index and we observe that for high fluences the refractive index decreases. The effect of the strain field on the density could explain the decrease in the refractive index. We check this hypothesis using our methodology coupling MD and FEM.

  3. Preparation of ion-track membranes of poly( p-phenylene terephthalamide): Control of pore shape by irradiation with different ion beams

    NASA Astrophysics Data System (ADS)

    Suzuki, Yasuyuki; Yamaki, Tetsuya; Koshikawa, Hiroshi; Asano, Masaharu; Voss, Kay-Obbe; Neumann, Reinhard; Yoshida, Masaru

    2007-07-01

    The preparation of ion-track membranes of thermally stable poly( p-phenylene terephthalamide) (PPTA) was performed by ion beam irradiation followed by chemical etching with a sodium hypochlorite solution. Cylindrical pores were observed in the membrane irradiated with 197Au and 238U ions at an energy of 11.1 MeV/n. In contrast, funnel shape pores appeared in the membrane irradiated with 84Kr, 102Ru and 129Xe ion at energies of 6.2, 3.6 and 3.5 MeV/n, respectively. The 197Au and 238U ion irradiation was found to exhibit more than four times larger sensitivity to the track etching under the same etching conditions. Consequently, the pore shape can be controlled by the masses and energies of the irradiated ions, in close relation to the etching sensitivity of the track.

  4. Mapping the Importance of Four Factors in Creating Monovalent Ion Selectivity in Biological Molecules

    PubMed Central

    Thomas, Michael; Jayatilaka, Dylan; Corry, Ben

    2011-01-01

    The ability of macrocycles, enzymes, ion channels, transporters, and DNA to differentiate among ion types is often crucial to their function. Using molecular dynamics simulations on both detailed systems and simple models, we quantify the importance of several factors which affect the ion selectivity of such molecules, including the number of coordinating ligands, their dipole moment, and their vibrational motion. The information resulting from our model systems is distilled into a series of selectivity maps that can be used to read off the relative free energy associated with binding of different ions, and to provide an estimate of the importance of the various factors. Although our maps cannot capture all elements of real systems, it is remarkable that they produce differential site-binding energies that are in line with experiment and more-detailed simulations for a variety of systems—making them useful for understanding the origins of selective binding and transport. The chemical nature of the coordinating ligands is essential for creating thermodynamic ion selectivity in flexible molecules (such as 18c6), but as the binding site becomes more rigid, the number of ligands (as in ion channels) and the reduction of thermal fluctuations (as in amino-acid transporters) can become important. In the future, our maps could aid in the determination of the local structure from binding energies and assist in the design of novel ion selective molecules. PMID:21190657

  5. Direct Observation of Defect Range and Evolution in Ion-Irradiated Single Crystalline Ni and Ni Binary Alloys

    DOE PAGES

    Lu, Chenyang; Jin, Ke; Béland, Laurent K.; ...

    2016-02-01

    We report that energetic ions have been widely used to evaluate the irradiation tolerance of structural materials for nuclear power applications and to modify material properties. It is important to understand the defect production, annihilation and migration mechanisms during and after collision cascades. In this study, single crystalline pure nickel metal and single-phase concentrated solid solution alloys of 50%Ni50%Co (NiCo) and 50%Ni50%Fe (NiFe) without apparent preexisting defect sinks were employed to study defect dynamics under ion irradiation. Both cross-sectional transmission electron microscopy characterization (TEM) and Rutherford backscattering spectrometry channeling (RBS-C) spectra show that the range of radiation-induced defect clusters farmore » exceed the theoretically predicted depth in all materials after high-dose irradiation. Defects in nickel migrate faster than in NiCo and NiFe. Both vacancy-type stacking fault tetrahedra (SFT) and interstitial loops coexist in the same region, which is consistent with molecular dynamics simulations. Kinetic activation relaxation technique (k-ART) simulations for nickel showed that small vacancy clusters, such as di-vacancies and tri-vacancies, created by collision cascades are highly mobile, even at room temperature. The slower migration of defects in the alloy along with more localized energy dissipation of the displacement cascade may lead to enhanced radiation tolerance.« less

  6. Direct Observation of Defect Range and Evolution in Ion-Irradiated Single Crystalline Ni and Ni Binary Alloys

    SciTech Connect

    Lu, Chenyang; Jin, Ke; Béland, Laurent K.; Zhang, Feifei; Yang, Taini; Qiao, Liang; Zhang, Yanwen; Bei, Hongbin; Christen, Hans M.; Stoller, Roger E.; Wang, Lumin

    2016-02-01

    We report that energetic ions have been widely used to evaluate the irradiation tolerance of structural materials for nuclear power applications and to modify material properties. It is important to understand the defect production, annihilation and migration mechanisms during and after collision cascades. In this study, single crystalline pure nickel metal and single-phase concentrated solid solution alloys of 50%Ni50%Co (NiCo) and 50%Ni50%Fe (NiFe) without apparent preexisting defect sinks were employed to study defect dynamics under ion irradiation. Both cross-sectional transmission electron microscopy characterization (TEM) and Rutherford backscattering spectrometry channeling (RBS-C) spectra show that the range of radiation-induced defect clusters far exceed the theoretically predicted depth in all materials after high-dose irradiation. Defects in nickel migrate faster than in NiCo and NiFe. Both vacancy-type stacking fault tetrahedra (SFT) and interstitial loops coexist in the same region, which is consistent with molecular dynamics simulations. Kinetic activation relaxation technique (k-ART) simulations for nickel showed that small vacancy clusters, such as di-vacancies and tri-vacancies, created by collision cascades are highly mobile, even at room temperature. The slower migration of defects in the alloy along with more localized energy dissipation of the displacement cascade may lead to enhanced radiation tolerance.

  7. Direct Observation of Defect Range and Evolution in Ion-Irradiated Single Crystalline Ni and Ni Binary Alloys

    PubMed Central

    Lu, Chenyang; Jin, Ke; Béland, Laurent K.; Zhang, Feifei; Yang, Taini; Qiao, Liang; Zhang, Yanwen; Bei, Hongbin; Christen, Hans M.; Stoller, Roger E.; Wang, Lumin

    2016-01-01

    Energetic ions have been widely used to evaluate the irradiation tolerance of structural materials for nuclear power applications and to modify material properties. It is important to understand the defect production, annihilation and migration mechanisms during and after collision cascades. In this study, single crystalline pure nickel metal and single-phase concentrated solid solution alloys of 50%Ni50%Co (NiCo) and 50%Ni50%Fe (NiFe) without apparent preexisting defect sinks were employed to study defect dynamics under ion irradiation. Both cross-sectional transmission electron microscopy characterization (TEM) and Rutherford backscattering spectrometry channeling (RBS-C) spectra show that the range of radiation-induced defect clusters far exceed the theoretically predicted depth in all materials after high-dose irradiation. Defects in nickel migrate faster than in NiCo and NiFe. Both vacancy-type stacking fault tetrahedra (SFT) and interstitial loops coexist in the same region, which is consistent with molecular dynamics simulations. Kinetic activation relaxation technique (k-ART) simulations for nickel showed that small vacancy clusters, such as di-vacancies and tri-vacancies, created by collision cascades are highly mobile, even at room temperature. The slower migration of defects in the alloy along with more localized energy dissipation of the displacement cascade may lead to enhanced radiation tolerance. PMID:26829570

  8. Direct Observation of Defect Range and Evolution in Ion-Irradiated Single Crystalline Ni and Ni Binary Alloys

    NASA Astrophysics Data System (ADS)

    Lu, Chenyang; Jin, Ke; Béland, Laurent K.; Zhang, Feifei; Yang, Taini; Qiao, Liang; Zhang, Yanwen; Bei, Hongbin; Christen, Hans M.; Stoller, Roger E.; Wang, Lumin

    2016-02-01

    Energetic ions have been widely used to evaluate the irradiation tolerance of structural materials for nuclear power applications and to modify material properties. It is important to understand the defect production, annihilation and migration mechanisms during and after collision cascades. In this study, single crystalline pure nickel metal and single-phase concentrated solid solution alloys of 50%Ni50%Co (NiCo) and 50%Ni50%Fe (NiFe) without apparent preexisting defect sinks were employed to study defect dynamics under ion irradiation. Both cross-sectional transmission electron microscopy characterization (TEM) and Rutherford backscattering spectrometry channeling (RBS-C) spectra show that the range of radiation-induced defect clusters far exceed the theoretically predicted depth in all materials after high-dose irradiation. Defects in nickel migrate faster than in NiCo and NiFe. Both vacancy-type stacking fault tetrahedra (SFT) and interstitial loops coexist in the same region, which is consistent with molecular dynamics simulations. Kinetic activation relaxation technique (k-ART) simulations for nickel showed that small vacancy clusters, such as di-vacancies and tri-vacancies, created by collision cascades are highly mobile, even at room temperature. The slower migration of defects in the alloy along with more localized energy dissipation of the displacement cascade may lead to enhanced radiation tolerance.

  9. Evaluation of hardening behaviors in ion-irradiated Fe-9Cr and Fe-20Cr alloys by nanoindentation technique

    NASA Astrophysics Data System (ADS)

    Li, Shilei; Wang, Yanli; Dai, Xianyuan; Liu, Fang; Li, Jinyu; Wang, Xitao

    2016-09-01

    The ion irradiation hardening behaviors of Fe-9 wt% Cr and Fe-20 wt% Cr model alloys were investigated by nanoindentation technique. The specimens were irradiated with 3 MeV Fe11+ ions at room temperature up to 1 and 5 dpa for Fe-9Cr alloy and 1 and 2.5 for Fe-20Cr alloy. The ratio of average hardness in the same depth of irradiated and unirradiated (Hirr. av/Hunirr. av) was used to determine the critical indentation depth hcrit to eliminate the softer substrate effect. The Nix-Gao model was used to explain the indentation size effect. Irradiation hardening is clearly observed in both Fe-9Cr alloy and Fe-20Cr alloy after ion irradiation. The differences of ISE and irradiation hardening behaviors between Fe-9Cr and Fe-20Cr alloys are considered to be due to their different microstructures and microstructural evolution under ion irradiation.

  10. Manipulation of transport hysteresis on graphene field effect transistors with Ga ion irradiation

    SciTech Connect

    Wang, Quan; Liu, Shuai; Ren, Naifei

    2014-09-29

    We have studied the effect of Ga ion irradiation on the controllable hysteretic behavior of graphene field effect transistors fabricated on Si/SO{sub 2} substrates. The various densities of defects in graphene were monitored by Raman spectrum. It was found that the Dirac point shifted to the positive gate voltage constantly, while the hysteretic behavior was enhanced first and then weakened, with the dose of ion irradiation increasing. By contrasting the trap charges density induced by dopant and the total density of effective trap charges, it demonstrated that adsorbate doping was not the decisive factor that induced the hysteretic behavior. The tunneling between the defect sites induced by ion irradiation was also an important cause for the hysteresis.

  11. Protective effects of shikonin on brain injury induced by carbon ion beam irradiation in mice.

    PubMed

    Gan, Lu; Wang, Zhen Hua; Zhang, Hong; Zhou, Rong; Sun, Chao; Liu, Yang; Si, Jing; Liu, Yuan Yuan; Wang, Zhen Guo

    2015-02-01

    Radiation encephalopathy is the main complication of cranial radiotherapy. It can cause necrosis of brain tissue and cognitive dysfunction. Our previous work had proved that a natural antioxidant shikonin possessed protective effect on cerebral ischemic injury. Here we investigated the effects of shikonin on carbon ion beam induced radiation brain injury in mice. Pretreatment with shikonin significantly increased the SOD and CAT activities and the ratio of GSH/GSSG in mouse brain tissues compared with irradiated group (P<0.01), while obviously reduced the MDA and PCO contents and the ROS levels derived from of the brain mitochondria. The shikonin also noticeably improved the spatial memory deficits caused by carbon ion beam irradiation. All results demonstrated that shikonin could improve the irradiated brain injury which might resulted from its modulation effects on the oxidative stress induced by the 12C6+ ion beam.

  12. Automatic system for single ion/single cell irradiation based on Cracow microprobe

    NASA Astrophysics Data System (ADS)

    Veselov, O.; Polak, W.; Lekki, J.; Stachura, Z.; Lebed, K.; Styczeń, J.; Ugenskiene, R.

    2006-05-01

    Recently, the Cracow ion microprobe has found its new application as a single ion hit facility (SIHF), allowing precise irradiations of living cells by a controlled number of ions. The instrument enables a broad field of research, such as survival studies, adaptive response investigations, bystander effect, inverse dose-rate effect, low-dose hypersensitivity, etc. This work presents principles of construction and operation of the SIHF based on the Cracow microprobe. We discuss some crucial features of optical, positioning, and blanking systems, including self-developed software responsible for semiautomatic cell recognition, for precise positioning of cells, and for controlling the irradiation process. We also show some tests carried out to determine the efficiency of the whole system and of its segments. In addition, we present results of the first irradiation measurements performed with living cells.

  13. Effects of O 7+ swift heavy ion irradiation on indium oxide thin films

    NASA Astrophysics Data System (ADS)

    Gokulakrishnan, V.; Parthiban, S.; Elangovan, E.; Ramamurthi, K.; Jeganathan, K.; Kanjilal, D.; Asokan, K.; Martins, R.; Fortunato, E.

    2011-08-01

    Indium oxide thin films deposited by spray pyrolysis were irradiated by 100 MeV O 7+ ions with different fluences of 5 × 10 11, 1 × 10 12 and 1 × 10 13 ions/cm 2. X-ray diffraction analysis confirmed the structure of indium oxide with cubic bixbyite. The strongest (2 2 2) orientation observed from the as-deposited films was shifted to (4 0 0) after irradiation. Furthermore, the intensity of the (4 0 0) orientation was decreased with increasing fluence together with an increase in (2 2 2) intensity. Films irradiated with maximum fluence exhibited an amorphous component. The mobility of the as-deposited indium oxide films was decreased from ˜78.9 to 43.0 cm 2/V s, following irradiation. Films irradiated with a fluence of 5 × 10 11 ions/cm 2 showed a better combination of electrical properties, with a resistivity of 4.57 × 10 -3 Ω cm, carrier concentration of 2.2 × 10 19 cm -3 and mobility of 61.0 cm 2/V s. The average transmittance obtained from the as-deposited films decreased from ˜81% to 72%, when irradiated with a fluence of 5 × 10 11 ions/cm 2. The surface microstructures confirmed that the irregularly shaped grains seen on the surface of the as-deposited films is modified as "radish-like" morphology when irradiated with a fluence of 5 × 10 11 ions/cm 2.

  14. Space Plasma Ion Processing of Ilmenite in the Lunar Soil: Insights from In-Situ TEM Ion Irradiation Experiments

    NASA Technical Reports Server (NTRS)

    Christoffersen, R.; Keller, L. P.

    2007-01-01

    Space weathering on the moon and asteroids results largely from the alteration of the outer surfaces of regolith grains by the combined effects of solar ion irradiation and other processes that include deposition of impact or sputter-derived vapors. Although no longer considered the sole driver of space weathering, solar ion irradiation remains a key part of the space weathering puzzle, and quantitative data on its effects on regolith minerals are still in short supply. For the lunar regolith, previous transmission electron microscope (TEM) studies performed by ourselves and others have uncovered altered rims on ilmenite (FeTiO3) grains that point to this phase as a unique "witness plate" for unraveling nanoscale space weathering processes. Most notably, the radiation processed portions of these ilmenite rims consistently have a crystalline structure, in contrast to radiation damaged rims on regolith silicates that are characteristically amorphous. While this has tended to support informal designation of ilmenite as a "radiation resistant" regolith mineral, there are to date no experimental data that directly and quantitatively compare ilmenite s response to ion radiation relative to lunar silicates. Such data are needed because the radiation processed rims on ilmenite grains, although crystalline, are microstructurally and chemically complex, and exhibit changes linked to the formation of nanophase Fe metal, a key space weathering process. We report here the first ion radiation processing study of ilmenite performed by in-situ means using the Intermediate Voltage Electron Microscope- Tandem Irradiation facility (IVEM-Tandem) at Argonne National Laboratory. The capability of this facility for performing real time TEM observations of samples concurrent with ion irradiation makes it uniquely suited for studying the dose-dependence of amorphization and other changes in irradiated samples.

  15. Mutation induction in bacteria after heavy ion irradiation

    NASA Technical Reports Server (NTRS)

    Horneck, G.; Kozubek, S.

    1994-01-01

    From a compilation of experimental data on the mutagenic effects of heavy ions in bacteria, main conclusions have been drawn as follows: (1) The mutagenic efficacy of heavy ions in bacteria depends on physical and biological variables. Physical variables are the radiation dose, energy and charge of the ion; the biological variables are the bacterial strain, the repair genotype of bacteria, and the endpoint investigated (type of mutation, induction of enzymes related to mutagenesis); (2) The responses on dose or fluence are mainly linear or linear quadratic. The quadratic component, if found for low LET radiation, is gradually reduced with increasing LET; (3) At low values of Z and LET the cross section of mutation induction sigma m (as well as SOS response, sigma sos. and lambda phage induction, sigma lambda versus LET curves can be quite consistently described by a common function which increases up to approximately 100 keV/mu m. For higher LET values, the sigma(m) versus LET curves show the so-called 'hooks' observed also for other endpoints; (4) For light ions (Z is less than or equal to 4), the cross sections mostly decrease with increasing ion energy, which is probably related to the decrease of the specific energy departed by the ion inside the sensitive volume (cell). For ions in the range of Z = 10, sigma(m) is nearly independent on the ion energy. For heavier ions (Z is greater than or equal to 16), sigma(m) increases with the energy up to a maximum or saturation around 10 MeV/u. The increment becomes steeper with increasing atomic number of the ion. It correlates with the increasing track radius of the heavy ion; (5) The mutagenic efficiency per lethal event changes slightly with ion energy, if Z is small indicating a rough correlation between cellular lethality and mutation induction, only. For ions of higher Z this relation increases with energy, indicating a change in the 'mode' of radiation action from 'killing-prone' to 'mutation-prone'; and (6

  16. Swift heavy ion irradiation of InP: Thermal spike modeling of track formation

    SciTech Connect

    Kamarou, A.; Wesch, W.; Wendler, E.; Undisz, A.; Rettenmayr, M.

    2006-05-01

    Irradiation of single-crystalline InP with swift heavy ions (SHI's) causes the formation of ion tracks for certain irradiation temperatures if the electronic energy deposition exceeds a threshold value. With increasing SHI fluence, more and more ion tracks are formed, until a continuous amorphous layer is produced due to the multiple overlapping of the tracks at high ion fluences. Single-crystalline InP samples were irradiated either at liquid nitrogen temperature (LNT) or at room temperature (RT) with Kr, Xe, or Au ions with specific energies ranging from ca. 0.3 to 3.0 MeV/u. Afterwards, the samples were investigated by means of Rutherford backscattering spectrometry and transmission electron microscopy in the plan-view and cross-section geometry. We show that the experimental data obtained can be qualitatively and quantitatively described on the basis of the inelastic thermal spike (TS) model, which was originally used only for metallic targets. The presented extension of the TS model on semiconductors covers mainly the very first stage of the energy transfer from SHI's (so-called 'ionization spikes'). Our results show that the extended TS model offers a self-consistent way to explain the influence of various irradiation conditions (ion mass, ion energy, irradiation temperature, etc.) on the ion track formation and damage accumulation in InP and, therefore, can make a contribution to a better understanding of the underlying mechanisms. Further, our results prejudice the amenity of a single value of the threshold electronic energy loss as a fundamental quantity that is commonly used for the description of track formation in solids irradiated with different ion species. There is no universal RT threshold for track formation in InP, but it is noticeably higher for lighter ions (12.0 and 14.8 keV/nm for RT irradiations with Au and Xe, respectively). Our experimental and simulation results support the idea that the formation of visible tracks requires a predamaging

  17. Swift heavy ion irradiation of InP: Thermal spike modeling of track formation

    NASA Astrophysics Data System (ADS)

    Kamarou, A.; Wesch, W.; Wendler, E.; Undisz, A.; Rettenmayr, M.

    2006-05-01

    Irradiation of single-crystalline InP with swift heavy ions (SHI’s) causes the formation of ion tracks for certain irradiation temperatures if the electronic energy deposition exceeds a threshold value. With increasing SHI fluence, more and more ion tracks are formed, until a continuous amorphous layer is produced due to the multiple overlapping of the tracks at high ion fluences. Single-crystalline InP samples were irradiated either at liquid nitrogen temperature (LNT) or at room temperature (RT) with Kr, Xe, or Au ions with specific energies ranging from ca. 0.3to3.0MeV/u . Afterwards, the samples were investigated by means of Rutherford backscattering spectrometry and transmission electron microscopy in the plan-view and cross-section geometry. We show that the experimental data obtained can be qualitatively and quantitatively described on the basis of the inelastic thermal spike (TS) model, which was originally used only for metallic targets. The presented extension of the TS model on semiconductors covers mainly the very first stage of the energy transfer from SHI’s (so-called “ionization spikes”). Our results show that the extended TS model offers a self-consistent way to explain the influence of various irradiation conditions (ion mass, ion energy, irradiation temperature, etc.) on the ion track formation and damage accumulation in InP and, therefore, can make a contribution to a better understanding of the underlying mechanisms. Further, our results prejudice the amenity of a single value of the threshold electronic energy loss as a fundamental quantity that is commonly used for the description of track formation in solids irradiated with different ion species. There is no universal RT threshold for track formation in InP, but it is noticeably higher for lighter ions (12.0 and 14.8keV/nm for RT irradiations with Au and Xe, respectively). Our experimental and simulation results support the idea that the formation of visible tracks requires a

  18. Grain growth and phase stability of nanocrystalline cubic zirconia under ion irradiation

    SciTech Connect

    Zhang, Yanwen; Jiang, Weilin; Wang, Chong M.; Namavar, Fereydoon; Edmondson, Philip D.; Zhu, Zihua; Gao, Fei; Lian, Jie; Weber, William J.

    2010-11-10

    Grain growth, oxygen stoichiometry and phase stability of nanostructurally-stabilized zirconia (NSZ) in pure cubic phase are investigated under 2 MeV Au ion bombardment at 160 and 400 K to doses up to 35 displacements per atom (dpa). The NSZ films are produced by ion-beam-assisted deposition technique at room temperature with an average grain size of 7.7 nm. The grain size increases with dose, and follows a power law (n=6) to a saturation value of ~30 nm that decreases with temperature. Slower grain growth is observed under 400 K irradiations, as compared to 160 K irradiations, indicating that thermal grain growth is not activated and defect-stimulated grain growth is the dominating mechanism. While cubic phase is perfectly retained and no new phases are identified after the high-dose irradiations, reduction of oxygen in the irradiated NSZ films is detected. The ratio of O to Zr decreases from ~2.0 for the as-deposited films to ~1.65 after irradiation to ~35 dpa. Significant increase of oxygen vacancies in nanocrystalline zirconia suggests substantially enhanced oxygen diffusion under ion irradiation, a materials behavior far from equilibrium. The oxygen deficiency may be essential in stabilizing cubic phase to larger grain sizes.

  19. Nitric oxide-mediated bystander signal transduction induced by heavy-ion microbeam irradiation

    NASA Astrophysics Data System (ADS)

    Tomita, Masanori; Matsumoto, Hideki; Funayama, Tomoo; Yokota, Yuichiro; Otsuka, Kensuke; Maeda, Munetoshi; Kobayashi, Yasuhiko

    2015-07-01

    In general, a radiation-induced bystander response is known to be a cellular response induced in non-irradiated cells after receiving bystander signaling factors released from directly irradiated cells within a cell population. Bystander responses induced by high-linear energy transfer (LET) heavy ions at low fluence are an important health problem for astronauts in space. Bystander responses are mediated via physical cell-cell contact, such as gap-junction intercellular communication (GJIC) and/or diffusive factors released into the medium in cell culture conditions. Nitric oxide (NO) is a well-known major initiator/mediator of intercellular signaling within culture medium during bystander responses. In this study, we investigated the NO-mediated bystander signal transduction induced by high-LET argon (Ar)-ion microbeam irradiation of normal human fibroblasts. Foci formation by DNA double-strand break repair proteins was induced in non-irradiated cells, which were co-cultured with those irradiated by high-LET Ar-ion microbeams in the same culture plate. Foci formation was suppressed significantly by pretreatment with an NO scavenger. Furthermore, NO-mediated reproductive cell death was also induced in bystander cells. Phosphorylation of NF-κB and Akt were induced during NO-mediated bystander signaling in the irradiated and bystander cells. However, the activation of these proteins depended on the incubation time after irradiation. The accumulation of cyclooxygenase-2 (COX-2), a downstream target of NO and NF-κB, was observed in the bystander cells 6 h after irradiation but not in the directly irradiated cells. Our findings suggest that Akt- and NF-κB-dependent signaling pathways involving COX-2 play important roles in NO-mediated high-LET heavy-ion-induced bystander responses. In addition, COX-2 may be used as a molecular marker of high-LET heavy-ion-induced bystander cells to distinguish them from directly irradiated cells, although this may depend on the time

  20. Nitric oxide-mediated bystander signal transduction induced by heavy-ion microbeam irradiation.

    PubMed

    Tomita, Masanori; Matsumoto, Hideki; Funayama, Tomoo; Yokota, Yuichiro; Otsuka, Kensuke; Maeda, Munetoshi; Kobayashi, Yasuhiko

    2015-07-01

    In general, a radiation-induced bystander response is known to be a cellular response induced in non-irradiated cells after receiving bystander signaling factors released from directly irradiated cells within a cell population. Bystander responses induced by high-linear energy transfer (LET) heavy ions at low fluence are an important health problem for astronauts in space. Bystander responses are mediated via physical cell-cell contact, such as gap-junction intercellular communication (GJIC) and/or diffusive factors released into the medium in cell culture conditions. Nitric oxide (NO) is a well-known major initiator/mediator of intercellular signaling within culture medium during bystander responses. In this study, we investigated the NO-mediated bystander signal transduction induced by high-LET argon (Ar)-ion microbeam irradiation of normal human fibroblasts. Foci formation by DNA double-strand break repair proteins was induced in non-irradiated cells, which were co-cultured with those irradiated by high-LET Ar-ion microbeams in the same culture plate. Foci formation was suppressed significantly by pretreatment with an NO scavenger. Furthermore, NO-mediated reproductive cell death was also induced in bystander cells. Phosphorylation of NF-κB and Akt were induced during NO-mediated bystander signaling in the irradiated and bystander cells. However, the activation of these proteins depended on the incubation time after irradiation. The accumulation of cyclooxygenase-2 (COX-2), a downstream target of NO and NF-κB, was observed in the bystander cells 6 h after irradiation but not in the directly irradiated cells. Our findings suggest that Akt- and NF-κB-dependent signaling pathways involving COX-2 play important roles in NO-mediated high-LET heavy-ion-induced bystander responses. In addition, COX-2 may be used as a molecular marker of high-LET heavy-ion-induced bystander cells to distinguish them from directly irradiated cells, although this may depend on the time

  1. Microstructure evolution of metallic nanocrystalline thin-films under ion-beam irradiation

    NASA Astrophysics Data System (ADS)

    Kaoumi, Djamel

    The microstructural evolution of nanocrystalline metallic thin-films under ion irradiation, especially grain growth and second-phase precipitation, was studied with detailed in situ experiments, and a theoretical model was developed to explain the results of grain-growth. Free-standing Zr, Pt, Cu and Au, Cu-Fe, and Zr-Fe nanocrystalline thin films prepared by sputter deposition were irradiated in-situ at the Intermediate Voltage Electron Microscope (IVEM) at Argonne National Laboratory with Ar and Kr ions to fluences in excess of 1016 ion/cm2 at temperatures ranging from 20 to 773 K. The microstructural evolution of the thin-films was followed in situ by systematically recording bright field images and diffraction patterns at successive ion-irradiation doses. Grain growth was observed as a result of irradiation in all samples at all irradiation temperatures. The results suggest the existence of three regimes with increasing irradiating temperature: a low temperature regime (below about 0.15 to 0.22 Tm) where grain-growth does not depend on the irradiation temperature, a thermally assisted regime where both the grain-growth rate and the final grain size increase with increasing irradiation temperature, and a thermal regime where thermal effects dominate ion beam effects. Similarly to thermal grain growth, the ion-irradiation induced grain growth curves could be best fitted with curves of the type: Dn-Dn0=KF with n˜3 in the low temperature regime. The effect of solute addition on grain-growth was investigated using Zr(Fe) and Cu(Fe) supersaturated solid-solutions. In the case of Zr-Fe, Zr2Fe precipitates formed during irradiation (with the dose-to-precipitation of Zr2Fe decreasing with increasing irradiation temperature), whereas Cu-Fe remained as a solid-solution. The grain-growth rate and final size decreased in both alloys with respect to the pure metallic films as a result of second-phase particle pinning (Zener drag) (Zr-Fe), and solute drag (Cu-Fe). The grain

  2. Stability of nanosized oxides in ferrite under extremely high dose self ion irradiations

    NASA Astrophysics Data System (ADS)

    Aydogan, E.; Almirall, N.; Odette, G. R.; Maloy, S. A.; Anderoglu, O.; Shao, L.; Gigax, J. G.; Price, L.; Chen, D.; Chen, T.; Garner, F. A.; Wu, Y.; Wells, P.; Lewandowski, J. J.; Hoelzer, D. T.

    2017-04-01

    A nanostructured ferritic alloy (NFA), 14YWT, was produced in the form of thin walled tubing. The stability of the nano-oxides (NOs) was determined under 3.5 MeV Fe+2 irradiations up to a dose of ∼585 dpa at 450 °C. Transmission electron microscopy (TEM) and atom probe tomography (APT) show that severe ion irradiation results in a ∼25% reduction in size between the unirradiated and irradiated case at 270 dpa while no further reduction within the experimental error was seen at higher doses. Conversely, number density increased by ∼30% after irradiation. This 'inverse coarsening' can be rationalized by the competition between radiation driven ballistic dissolution and diffusional NO reformation. No significant changes in the composition of the matrix or NOs were observed after irradiation. Modeling the experimental results also indicated a dissolution of the particles.

  3. Stability of nanosized oxides in ferrite under extremely high dose self ion irradiations

    DOE PAGES

    Aydogan, E.; Almirall, N.; Odette, G. R.; ...

    2017-01-10

    We produced a nanostructured ferritic alloy (NFA), 14YWT, in the form of thin walled tubing. The stability of the nano-oxides (NOs) was determined under 3.5 MeV Fe+2 irradiations up to a dose of ~585 dpa at 450 °C. Transmission electron microscopy (TEM) and atom probe tomography (APT) show that severe ion irradiation results in a ~25% reduction in size between the unirradiated and irradiated case at 270 dpa while no further reduction within the experimental error was seen at higher doses. Conversely, number density increased by ~30% after irradiation. Moreover, this ‘inverse coarsening’ can be rationalized by the competition betweenmore » radiation driven ballistic dissolution and diffusional NO reformation. There were no significant changes in the composition of the matrix or NOs observed after irradiation. Modeling the experimental results also indicated a dissolution of the particles.« less

  4. Stability of nanosized oxides in ferrite under extremely high dose self ion irradiations

    DOE PAGES

    Aydogan, E.; Almirall, N.; Odette, G. R.; ...

    2017-01-10

    We produced a nanostructured ferritic alloy (NFA), 14YWT, in the form of thin walled tubing. The stability of the nano-oxides (NOs) was determined under 3.5 MeV Fe+2 irradiations up to a dose of ~585 dpa at 450 °C. Transmission electron microscopy (TEM) and atom probe tomography (APT) show that severe ion irradiation results in a ~25% reduction in size between the unirradiated and irradiated case at 270 dpa while no further reduction within the experimental error was seen at higher doses. Conversely, number density increased by ~30% after irradiation. Moreover, this ‘inverse coarsening’ can be rationalized by the competition betweenmore » radiation driven ballistic dissolution and diffusional NO reformation. There were no significant changes in the composition of the matrix or NOs observed after irradiation. Modeling the experimental results also indicated a dissolution of the particles.« less

  5. Development and performance evaluation of a three-dimensional clinostat synchronized heavy-ion irradiation system

    NASA Astrophysics Data System (ADS)

    Ikeda, Hiroko; Souda, Hikaru; Puspitasari, Anggraeini; Held, Kathryn D.; Hidema, Jun; Nikawa, Takeshi; Yoshida, Yukari; Kanai, Tatsuaki; Takahashi, Akihisa

    2017-02-01

    Outer space is an environment characterized by microgravity and space radiation, including high-energy charged particles. Astronauts are constantly exposed to both microgravity and radiation during long-term stays in space. However, many aspects of the biological effects of combined microgravity and space radiation remain unclear. We developed a new three-dimensional (3D) clinostat synchronized heavy-ion irradiation system for use in ground-based studies of the combined exposures. Our new system uses a particle accelerator and a respiratory gating system from heavy-ion radiotherapy to irradiate samples being rotated in the 3D clinostat with carbon-ion beams only when the samples are in the horizontal position. A Peltier module and special sample holder were loaded on a static stage (standing condition) and the 3D clinostat (rotation condition) to maintain a suitable temperature under atmospheric conditions. The performance of the new device was investigated with normal human fibroblasts 1BR-hTERT in a disposable closed cell culture chamber. Live imaging revealed that cellular adhesion and growth were almost the same for the standing control sample and rotation sample over 48 h. Dose flatness and symmetry were judged according to the relative density of Gafchromic films along the X-axis and Y-axis of the positions of the irradiated sample to confirm irradiation accuracy. Doses calculated using the carbon-ion calibration curve were almost the same for standing and rotation conditions, with the difference being less than 5% at 1 Gy carbon-ion irradiation. Our new device can accurately synchronize carbon-ion irradiation and simulated microgravity while maintaining the temperature under atmospheric conditions at ground level.

  6. Comparison of human lung cancer cell radiosensitivity after irradiations with therapeutic protons and carbon ions.

    PubMed

    Keta, Otilija D; Todorović, Danijela V; Bulat, Tanja M; Cirrone, Pablo Ga; Romano, Francesco; Cuttone, Giacomo; Petrović, Ivan M; Ristić Fira, Aleksandra M

    2017-05-01

    The aim of this study was to investigate effects of irradiations with the therapeutic proton and carbon ion beams in two non-small cell lung cancers, CRL5876 adenocarcinoma and HTB177 large cell lung carcinoma. The DNA damage response dynamics, cell cycle regulation, and cell death pathway activation were followed. Viability of both cell lines was lower after carbon ions compared to the therapeutic proton irradiations. HTB177 cells showed higher recovery than CRL5876 cells seven days following the treatments, but the survival rates of both cell lines were lower after exposure to carbon ions with respect to therapeutic protons. When analyzing cell cycle distribution of both CRL5876 and HTB177 cells, it was noticed that therapeutic protons predominantly induced G1 arrest, while the cells after carbon ions were arrested in G2/M phase. The results illustrated that differences in the levels of phosphorylated H2AX, a double-strand break marker, exist after therapeutic proton and carbon ion irradiations. We also observed dose- and time-dependent increase in the p53 and p21 levels after applied irradiations. Carbon ions caused larger increase in the quantity of p53 and p21 compared to therapeutic protons. These results suggested that various repair mechanisms were induced in the treated cells. Considering the fact that we have not observed any distinct change in the Bax/Bcl-2 ratio following irradiations, it seemed that different types of cell death were involved in the response to the two types of irradiations that were applied.

  7. Development and performance evaluation of a three-dimensional clinostat synchronized heavy-ion irradiation system.

    PubMed

    Ikeda, Hiroko; Souda, Hikaru; Puspitasari, Anggraeini; Held, Kathryn D; Hidema, Jun; Nikawa, Takeshi; Yoshida, Yukari; Kanai, Tatsuaki; Takahashi, Akihisa

    2017-02-01

    Outer space is an environment characterized by microgravity and space radiation, including high-energy charged particles. Astronauts are constantly exposed to both microgravity and radiation during long-term stays in space. However, many aspects of the biological effects of combined microgravity and space radiation remain unclear. We developed a new three-dimensional (3D) clinostat synchronized heavy-ion irradiation system for use in ground-based studies of the combined exposures. Our new system uses a particle accelerator and a respiratory gating system from heavy-ion radiotherapy to irradiate samples being rotated in the 3D clinostat with carbon-ion beams only when the samples are in the horizontal position. A Peltier module and special sample holder were loaded on a static stage (standing condition) and the 3D clinostat (rotation condition) to maintain a suitable temperature under atmospheric conditions. The performance of the new device was investigated with normal human fibroblasts 1BR-hTERT in a disposable closed cell culture chamber. Live imaging revealed that cellular adhesion and growth were almost the same for the standing control sample and rotation sample over 48h. Dose flatness and symmetry were judged according to the relative density of Gafchromic films along the X-axis and Y-axis of the positions of the irradiated sample to confirm irradiation accuracy. Doses calculated using the carbon-ion calibration curve were almost the same for standing and rotation conditions, with the difference being less than 5% at 1Gy carbon-ion irradiation. Our new device can accurately synchronize carbon-ion irradiation and simulated microgravity while maintaining the temperature under atmospheric conditions at ground level. Copyright © 2017 The Committee on Space Research (COSPAR). Published by Elsevier Ltd. All rights reserved.

  8. Phase stability in thermally-aged CASS CF8 under heavy ion irradiation

    SciTech Connect

    Li, Meimei; Miller, Michael K.; Chen, Wei-Ying

    2015-07-01

    The stability of the microstructure of a cast austenitic stainless steel (CASS), before and after heavy ion irradiation, was investigated by atom probe tomography (APT). A CF8 ferrite-austenite duplex alloy was thermally aged at 400 degrees C for 10,000 h. After this treatment, APT revealed nanometer-sized G-phase precipitates and Fe-rich alpha and Cr-enriched alpha' phase separated regions in the ferrite. The thermally-aged CF8 specimen was irradiated with 1 MeV Kr ions to a fluence of 1.88 x 10(19) ions/m(2) at 400 degrees C. After irradiation, APT analysis revealed a strong spatial/dose dependence of the G-phase precipitates and the alpha-alpha' spinodal decomposition in the ferrite. For the G-phase precipitates, the number density increased and the mean size decreased with increasing dose, and the particle size distribution changed considerably under irradiation. The inverse coarsening process can be described by recoil resolution. The amplitude of the alpha-alpha' spinodal decomposition in the ferrite was apparently reduced after heavy ion irradiation. (C) 2015 Elsevier B.V. All rights reserved

  9. Effect of swift heavy ion irradiation on bare and coated ZnS quantum dots

    SciTech Connect

    Chowdhury, S. Hussain, A.M.P.; Ahmed, G.A.; Singh, F.; Avasthi, D.K.; Choudhury, A.

    2008-12-01

    The present study compares structural and optical modifications of bare and silica (SiO{sub 2}) coated ZnS quantum dots under swift heavy ion (SHI) irradiation. Bare and silica coated ZnS quantum dots were prepared following an inexpensive chemical route using polyvinyl alcohol (PVA) as the dielectric host matrix. X-ray diffraction (XRD) and transmission electron microscopy (TEM) study of the samples show the formation of almost spherical ZnS quantum dots. The UV-Vis absorption spectra reveal blue shift relative to bulk material in absorption energy while photoluminescence (PL) spectra suggests that surface state and near band edge emissions are dominating in case of bare and coated samples, respectively. Swift heavy ion irradiation of the samples was carried out with 160 MeV Ni{sup 12+} ion beam with fluences 10{sup 12} to 10{sup 13} ions/cm{sup 2}. Size enhancement of bare quantum dots after irradiation has been indicated in XRD and TEM analysis of the samples which has also been supported by optical absorption spectra. However similar investigations on irradiated coated quantum dots revealed little change in quantum dot size and emission. The present study thus shows that the coated ZnS quantum dots are stable upon SHI irradiation compared to the bare one.

  10. Color center annealing and ageing in electron and ion-irradiated yttria-stabilized zirconia

    NASA Astrophysics Data System (ADS)

    Costantini, Jean-Marc; Beuneu, François

    2005-04-01

    We have used X-band electron paramagnetic resonance (EPR) measurements at room-temperature (RT) to study the thermal annealing and RT ageing of color centers induced in yttria-stabilized zirconia (YSZ), i.e. ZrO2:Y with 9.5 mol% Y2O3, by swift electron and ion-irradiations. YSZ single crystals with the <1 0 0> orientation were irradiated with 2.5 MeV electrons, and implanted with 100 MeV 13C ions. Electron and ion beams produce the same two color centers, namely an F+-type center (singly ionized oxygen vacancy) and the so-called T-center (Zr3+ in a trigonal oxygen local environment) which is also produced by X-ray irradiations. Isochronal annealing was performed in air up to 973 K. For both electron and ion irradiations, the defect densities are plotted versus temperature or time at various fluences. The influence of a thermal treatment at 1373 K of the YSZ single crystals under vacuum prior to the irradiations was also investigated. In these reduced samples, color centers are found to be more stable than in as-received samples. Two kinds of recovery processes are observed depending on fluence and heat treatment.

  11. Photoinduced currents in pristine and ion irradiated kapton-H polyimide

    SciTech Connect

    Sharma, Anu Sridharbabu, Y. Quamara, J. K.

    2014-10-15

    The photoinduced currents in pristine and ion irradiated kapton-H polyimide have been investigated for different applied electric fields at 200°C. Particularly the effect of illumination intensity on the maximum current obtained as a result of photoinduced polarization has been studied. Samples were irradiated by using PELLETRON facility, IUAC, New Delhi. The photo-carrier charge generation depends directly on intensity of illumination. The samples irradiated at higher fluence show a decrease in the peak current with intensity of illumination. The secondary radiation induced crystallinity (SRIC) is responsible for the increase in maximum photoinduced currents generated with intensity of illumination.

  12. Variation of hardness and modulus of borosilicate glass irradiated with Kr ions

    NASA Astrophysics Data System (ADS)

    Peng, H. B.; Sun, M. L.; Du, X.; Yuan, W.; Yang, D.; Chen, L.; Duan, B. H.; Wang, T. S.

    2017-09-01

    Borosilicate glass has potential application for vitrification of high-level waste, which attracts extensive interest in studying their radiation durability. The NBS1 and NBS2 glasses were irradiated with 4 MeV Kr ions. The hardness and modulus of irradiated glasses were measured with a MTS G200 Nanoindenter device. With the increase of the irradiation, both the values of hardness and the modulus dropped and then saturated. The trend was consistent with previous studies, but the decay constants for the hardness of NBS1 and NBS2 were less than those in previous studies.

  13. Formation and coarsening of Ga droplets on focused-ion-beam irradiated GaAs surfaces

    SciTech Connect

    Wu, J. H.; Ye, W.; Cardozo, B. L.; Saltzman, D.; Sun, K.; Sun, H.; Mansfield, J. F.; Goldman, R. S.

    2009-10-12

    We have investigated the formation and coarsening of Ga droplets on focused-ion-beam (FIB) irradiated GaAs surfaces. To separately examine formation and coarsening, Ga droplets were fabricated by Ga{sup +} FIB irradiation of GaAs substrates with and without pre-patterned holes. We determined the droplet growth rate and size distribution as a function of FIB energy following irradiation. The data suggest a droplet formation mechanism that involves Ga precipitation from a Ga-rich layer, followed by droplet coarsening via a combination of diffusion and Ostwald ripening or coalescence via droplet migration (dynamic coalescence)

  14. [Induction of the Tn10 precise excision in E. coli cells after accelerated heavy ions irradiation].

    PubMed

    Zhuravel', D V

    2004-01-01

    The influence of the irradiation of different kinds on the induction of the structural mutations in the bacteria Escherichia coli is considered. The regularities of the Tn10 precise excision after accelerated 4He and 12C ions irradiations with different linear energy transfer (LET) were investigated. Dose dependences of the survival and relative frequency of the Tn10 precise excision were obtained. It was shown, that the relative frequency of the Tn10 precise excision is the exponential function from the irradiation dose. Relative biological efficiency (RBE), and relative genetic efficiency (RGE) were calculated, and were treated as the function of the LET.

  15. Microstructural stability of a self-ion irradiated lanthana-bearing nanostructured ferritic steel

    SciTech Connect

    Pasebani, Somayeh; Charit, Indrajit; Burns, Jatuporn; Alsagabi, Sultan; Butt, Darryl P.; Cole, James I.; Price, Lloyd M.; Shao, Lin

    2015-07-01

    Thermally stable nanofeatures with high number density are expected to impart excellent high temperature strength and irradiation stability in nanostructured ferritic steels (NFSs) which have potential applications in advanced nuclear reactors. A lanthana-bearing NFS (14LMT) developed via mechanical alloying and spark plasma sintering was used in this study. The sintered samples were irradiated by Fe2+ ions to 10, 50 and 100 dpa at 30 °C and 500 °C. Microstructural and mechanical characteristics of the irradiated samples were studied using different microscopy techniques and nanoindentation, respectively. Overall morphology and number density of the nanofeatures remained unchanged after irradiation. Average radius of nanofeatures in the irradiated sample (100 dpa at 500 °C) was slightly reduced. A notable level of irradiation hardening and enhanced dislocation activity occurred after ion irradiation except at 30 °C and ≥50 dpa. Other microstructural features like grain boundaries and high density of dislocations also provided defect sinks to assist in defect removal.

  16. Dancing to the MUSSIC: Steps towards creating a Multisatellite Ultraviolet Solar Spectral Irradiance Composite

    NASA Astrophysics Data System (ADS)

    Snow, M. A.; Machol, J. L.; Richard, E. C.

    2016-12-01

    Solar spectral irradiance (SSI) has been measured since the beginning of the satellite era in 1978, but the observational record has many gaps in both wavelength and time. We describe our current effort in linking several such datasets ranging from the Extreme Ultraviolet to the Near Ultraviolet (0-400 nm). This wavelength range includes two important solar activity proxies, the Magnesium II core—to-wing ratio and the Lyman alpha irradiance, and special attention will be applied to these two wavelength intervals.

  17. Analysis of Heavy Ion Irradiation Induced Thermal Damage in SiC Schottky Diodes

    NASA Astrophysics Data System (ADS)

    Abbate, C.; Busatto, G.; Cova, P.; Delmonte, N.; Giuliani, F.; Iannuzzo, F.; Sanseverino, A.; Velardi, F.

    2015-02-01

    A study is presented aimed at describing phenomena involved in Single Event Burnout induced by heavy ion irradiation in SiC Schottky diodes. On the basis of experimental data obtained for 79Br irradiation at different energies, electro-thermal FEM is used to demonstrate that the failure is caused by a strong local increase of the semiconductor temperature. With respect to previous studies the temperature dependent thermal material properties were added. The critical ion energy calculated by this model is in agreement with literature experimental results. The substrate doping dependence of the SEE robustness was analyzed, proving the effectiveness of the developed model for device technological improvements.

  18. Combined High Pressure and Heavy-Ion Irradiation: a Novel Approach

    SciTech Connect

    Lang, M.; Zhang, F; Lian, J; Trautmann, C; Neumann, R; Ewing, R

    2009-01-01

    Swift heavy-ion irradiations of a wide variety of materials have been used to modify and manipulate the properties of solids at the nanoscale. Recently, these high-energy irradiations have been successfully combined with high-pressure experiments. Based on results obtained for zircon (ZrSiO{sub 4}), this paper introduces this new experimental approach involving diamond anvil cells and large ion-accelerator facilities. This technique provides a wide spectrum of geoscience applications from nanoscale simulations of fission-track formation under crustal conditions to phase transitions of radiation-damaged minerals resulting from meteorite impact.

  19. Fabricating high-density magnetic storage elements by low-dose ion beam irradiation

    SciTech Connect

    Neb, R.; Sebastian, T.; Pirro, P.; Hillebrands, B.; Pofahl, S.; Schaefer, R.; Reuscher, B.

    2012-09-10

    We fabricate magnetic storage elements by irradiating an antiferromagnetically coupled ferromagnetic/nonmagnetic/ferromagnetic trilayer by a low-dose ion beam. The irradiated areas become ferromagnetically coupled and are capable of storing information if their size is small enough. We employ Fe/Cr/Fe trilayers and a 30 keV focused Ga{sup +}-ion beam to demonstrate the working principle for a storage array with a bit density of 7 Gbit/in.{sup 2}. Micromagnetic simulations suggest that bit densities of at least two magnitudes of order larger should be possible.

  20. Evaluation of Surface Damage of Organic Films due to Irradiation with Energetic Ion Beams

    SciTech Connect

    Hada, Masaki; Hontani, Yusaku; Ichiki, Kazuya; Seki, Toshio; Ibuki, Sachi; Ninomiya, Satoshi; Matsuo, Jiro; Aoki, Takaaki

    2011-01-07

    The surface of L-leucine films irradiated with an Ar{sub 5000} cluster ion beam (5 keV) was characterized by using the X-ray reflective (XRR) measurement method, atomic force microscopy (AFM) and ellipsometry. No significant damage was detected on the surface of the L-leucine films irradiated with the Ar cluster ion beam. Therefore, the large cluster-low-energy (about 1 eV/atom) beam would be suitable for low-damage etching of organic materials.

  1. Hardness enhancement and crosslinking mechanisms in polystyrene irradiated with high energy ion-beams

    SciTech Connect

    Lee, E.H.; Rao, G.R.; Mansur, L.K.

    1996-12-31

    Surface hardness values several times larger than steel were produced using high energy ion beams at several hundred keV to MeV. High LET is important for crosslinking. Crosslinking is studied by analyzing hardness variations in response to irradiation parameter such as ion species, energy, and fluence. Effective crosslinking radii at hardness saturation are derived base on experimental data for 350 keV H{sup +} and 1 MeV Ar{sup +} irradiation of polystyrene. Saturation value for surface hardness is about 20 GPa.

  2. Large scale silver nanowires network fabricated by MeV hydrogen (H+) ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Honey, S.; Naseem, S.; Ishaq, A.; Maaza, M.; Bhatti, M. T.; Wan, D.

    2016-04-01

    A random two-dimensional large scale nano-network of silver nanowires (Ag-NWs) is fabricated by MeV hydrogen (H+) ion beam irradiation. Ag-NWs are irradiated under H+ ion beam at different ion fluences at room temperature. The Ag-NW network is fabricated by H+ ion beam-induced welding of Ag-NWs at intersecting positions. H+ ion beam induced welding is confirmed by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). Moreover, the structure of Ag NWs remains stable under H+ ion beam, and networks are optically transparent. Morphology also remains stable under H+ ion beam irradiation. No slicings or cuttings of Ag-NWs are observed under MeV H+ ion beam irradiation. The results exhibit that the formation of Ag-NW network proceeds through three steps: ion beam induced thermal spikes lead to the local heating of Ag-NWs, the formation of simple junctions on small scale, and the formation of a large scale network. This observation is useful for using Ag-NWs based devices in upper space where protons are abandoned in an energy range from MeV to GeV. This high-quality Ag-NW network can also be used as a transparent electrode for optoelectronics devices. Project supported by the National Research Foundation of South Africa (NRF), the French Centre National pour la Recherche Scientifique, iThemba-LABS, the UNESCO-UNISA Africa Chair in Nanosciences & Nanotechnology, the Third World Academy of Science (TWAS), Organization of Women in Science for the Developing World (OWSDW), the Abdus Salam ICTP via the Nanosciences African Network (NANOAFNET), and the Higher Education Commission (HEC) of Pakistan.

  3. Effect of low energy ion beam irradiation on wettability of narra ( Pterocarpus indicus) wood chips

    NASA Astrophysics Data System (ADS)

    Ramos, Henry J.; Monasterial, Jonathan Lee C.; Blantocas, Gene Q.

    2006-01-01

    Narra (Pterocarpus indicus) wood chips were irradiated with positive hydrogen ions H+ and H2+ to make them hydrophobic. The ions were produced and extracted from a gas discharge ion source. The extracted beam current ranges from 0.01 to 0.07 μA for discharge currents of 1.0-4.0 mA, discharge potential between 600 V and 1000 V. The chips, positioned at 70 mm downstream from the ion source, were processed for different time periods and discharge currents. The wettability was characterized by the contact angle of the liquid droplet with respect to the wood surface. Surface modifications were assessed with by measurements of the water contact angle. Tests indicate retarded absorption characteristics for ion-irradiated samples compared to controlled samples. The longest absorptive inhibition were exhibited by samples irradiated for 30 min, at discharge current of 1.0 mA, 720 eV ion energy and 0 V extraction potential. Scanning electron micrographs reveal the difference in morphologies of treated and untreated samples. The results prove that low energy beams of hydrogen from a gas discharge ion source are suitable in transforming surfaces of wood chips to be water resistant.

  4. Silicon Carbide Power Device Performance Under Heavy-Ion Irradiation

    NASA Technical Reports Server (NTRS)

    Lauenstein, Jean-Marie; Casey, Megan; Topper, Alyson; Wilcox, Edward; Phan, Anthony; Ikpe, Stanley; LaBel, Ken

    2015-01-01

    Heavy-ion induced degradation and catastrophic failure data for SiC power MOSFETs and Schottky diodes are examined to provide insight into the challenge of single-event effect hardening of SiC power devices.

  5. Redox changes induced in hippocampal precursor cells by heavy ion irradiation.

    PubMed

    Limoli, C L; Giedzinski, E; Baure, J; Rola, R; Fike, J R

    2007-06-01

    Hippocampal precursors retain the capacity to proliferate and differentiate throughout life, and their progeny, immature neurons, can undergo neurogenesis, a process believed to be important in maintaining the cognitive health of an organism. A variety of stresses including irradiation have been shown to deplete neural precursor cells, an effect that inhibits neurogenesis and is associated with the onset of cognitive impairments. Our past work has shown that neural precursor cells exposed to X-rays or protons exhibit a prolonged increase in oxidative stress, a factor we hypothesize to be critical in regulating the function of these cells after irradiation and other stresses. Here we report that irradiation of hippocampal precursor cells with high-linear energy transfer (LET) 1 GeV/nucleon 56Fe ions leads to significantly higher levels of oxidative stress when compared to lower LET radiations (X-rays, protons). Irradiation with 1 Gy of 56Fe ions elicits twofold to fivefold higher levels of reactive oxygen species (ROS) compared to unirradiated controls, and at lower doses (ion exposure. The use of the antioxidant lipoic acid (LA) was able to reduce ROS levels below background levels when added before or after 56Fe ion irradiation. These results conclusively show that low doses of 56Fe ions can elicit significant levels of oxidative stress in neural precursor cells. Given the prevalence of heavy ions in space and the duration of interplanetary travel, these data suggest that astronauts are at risk for developing cognitive decrements. However, our results also indicate that antioxidants delivered before as radioprotective agents or after as mitigating agents hold promise as effective countermeasures for ameliorating certain adverse effects of heavy ion exposure to the CNS.

  6. Mechanical properties and plasticity size effect of Fe-6%Cr irradiated by Fe ions and by neutrons

    NASA Astrophysics Data System (ADS)

    Hardie, C. D.; Odette, G. R.; Wu, Y.; Akhmadaliev, S.; Roberts, S. G.

    2016-12-01

    The mechanical behaviour of Fe6%Cr in the un-irradiated, self-ion irradiated and neutron irradiated conditions was measured and compared. Irradiations were performed to the same dose and at the same temperature but to very different damage rates for both methods. The materials were tested using nanoindentation and micromechanical testing, and compared with microstructural observations from Transmission Electron Microscopy (TEM) and Atom Probe Tomography (APT) reported elsewhere. Irradiated and un-irradiated micro-cantilevers with a wide range of dimensions were used to study the interrelationships between irradiation hardening and size effects in small-scale plasticity. TEM and APT results identified that the dislocation loop densities were ∼2.9 × 1022m-3 for the neutron irradiated material and only 1.4 × 1022m-3 for the ion irradiated material. Cr segregation to loops was only found for the neutron-irradiated material. The nanoindentation hardness increase due to neutron irradiation was 3 GPa and that due to ion irradiation 1 GPa. The differences between the effects of the two irradiation types are discussed, taking into account inconsistencies in damage calculations, and the differences in PKA spectra, dose rate and transmutation products for the two irradiation types.

  7. Microstructural response of InGaN to swift heavy ion irradiation

    SciTech Connect

    Zhang, L. M.; Jiang, W.; Fadanelli, R. C.; Ai, W. S.; Peng, J. X.; Wang, T. S.; Zhang, C. H.

    2016-12-01

    A monocrystalline In0.18Ga0.82N film of ~275 nm in thickness grown on a GaN/Al2O3 substrate was irradiated with 290 MeV 238U32+ ions to a fluence of 1.2 x 12 cm-2 at room temperature. The irradiated sample was characterized using helium ion microscopy (HIM), Rutherford backscattering spectrometry under ion-channeling conditions (RBS/C), and high-resolution x-ray diffraction (HRXRD). The irradiation leads to formation of ion tracks throughout the thin In0.18Ga0.82N film and the 3.0 µm thick GaN buffer layer. The mean diameter of the tracks in In0.18Ga0.82N is ~9 nm, as determined by HIM examination. Combination of the HIM and RBS/C data suggests that the material in the track is likely to be highly disordered or fully amorphized, in contrast to a crystalline structure within the ion track in GaN. Lattice relaxation in In0.18Ga0.82N and a distribution of d-spacing of the (0002) planes in GaN with lattice expansion are observed after irradiation.

  8. Amorphization of nanocrystalline monoclinic ZrO2 by swift heavy ion irradiation.

    PubMed

    Lu, Fengyuan; Wang, Jianwei; Lang, Maik; Toulemonde, Marcel; Namavar, Fereydoon; Trautmann, Christina; Zhang, Jiaming; Ewing, Rodney C; Lian, Jie

    2012-09-21

    Bulk ZrO(2) polymorphs generally have an extremely high amorphization tolerance upon low energy ion and swift heavy ion irradiation in which ballistic interaction and ionization radiation dominate the ion-solid interaction, respectively. However, under very high-energy irradiation by 1.33 GeV U-238, nanocrystalline (40-50 nm) monoclinic ZrO(2) can be amorphized. A computational simulation based on a thermal spike model reveals that the strong ionizing radiation from swift heavy ions with a very high electronic energy loss of 52.2 keV nm(-1) can induce transient zones with temperatures well above the ZrO(2) melting point. The extreme electronic energy loss, coupled with the high energy state of the nanostructured materials and a high thermal confinement due to the less effective heat transport within the transient hot zone, may eventually be responsible for the ionizing radiation-induced amorphization without transforming to the tetragonal polymorph. The amorphization of nanocrystalline zirconia was also confirmed by 1.69 GeV Au ion irradiation with the electronic energy loss of 40 keV nm(-1). These results suggest that highly radiation tolerant materials in bulk forms, such as ZrO(2), may be radiation sensitive with the reduced length scale down to the nano-metered regime upon irradiation above a threshold value of electronic energy loss.

  9. Swift heavy-ion irradiation effects on electrical and defect properties of NPN transistors

    NASA Astrophysics Data System (ADS)

    Gnana Prakash, A. P.; Ke, S. C.; Siddappa, K.

    2004-08-01

    NPN transistors were irradiated by 95 MeV oxygen ions in a fluence ranging from 5 × 1010 to 5 × 1012 ions cm-2. The dc current gain (hFE), excess base current (DgrIB = IBpost - IBpre), excess collector current (DgrIC = ICpost - ICpre) and collector-saturation current (ICS) of the ion-irradiated transistors were studied systematically. We found that both hFE and ICS of the transistors decrease drastically after ion irradiation. Secondly, a significant increase in the collector current (IC) along with the increase in the base current (IB) after ion irradiation was observed. The radiation-induced trap levels in the collector-base depletion region of NPN transistors were studied by employing the deep level transient spectroscopy technique and different types of trap levels were observed. The results obtained on the activation energy, density of trap levels, apparent capture cross section of the defects, introduction rate and space charge layer lifetime of different defects for different total fluence are presented and discussed.

  10. Determination of cross-link density in ion-irradiated polystyrene surfaces from rippling.

    PubMed

    Karade, Yogesh; Pihan, Sascha A; Brünger, Wilhelm H; Dietzel, Andreas; Berger, Rüdiger; Graf, Karlheinz

    2009-03-03

    The irradiation of polymer surfaces with ion beams leads to pronounced chemical and physical modifications when the ions are scattered at the atoms in the polymer chain. In this way, different products of decomposition occur. Here we show that by changing the ion fluence and the mass of the ion the local mechanical properties as Young's modulus of a polystyrene surface layer can be tailored. By annealing prestretched irradiated PS near the glass transition, surface rippling occurs in the irradiated areas only, which can be described with an elastic model. The moduli obtained from rippling periodicities and elastic model assumptions are in the range between 8 and 800 MPa at the glass transition and characterize the irradiated PS as rubberlike. From these values the network density and the molar mass of entanglement are quantified. The obtained network density equals the density of hydrogen vacancies generated through the scattered ions, as confirmed by simulations of the atomic scattering and displacement processes. The obtained molar mass of entanglement reveals that the PS locally was densely cross-linked. Our results show that even for nondiscrete layered polymer systems relevant polymer parameters can be derived from the well-known surface rippling without the need for costly chemical analysis.

  11. Structural modifications of diamond like carbon films induced by MeV nitrogen ion irradiation

    NASA Astrophysics Data System (ADS)

    Mathew, S.; Bhatta, U. M.; Islam, A. K. M. Maidul; Mukherjee, M.; Ray, N. R.; Dev, B. N.

    2009-02-01

    Diamond-like carbon (DLC) films were deposited on Si(1 0 0) substrates using plasma deposition technique. The deposited films were irradiated using 2 MeV N + ions at fluences of 1×1014, 1×1015 and 5×1015 ions/cm 2. Samples have been characterized by using Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electron microscopy (HRTEM). Analysis of Raman spectra shows a gradual shift of both D and G band peaks towards higher frequencies along with an increase of the intensity ratio, I(D)/ I(G), with increasing ion fluence in irradiation. These results are consistent with an increase of sp 2 bonding. XPS results also show a monotonic increase of sp 2/sp 3 hybridization ratio with increasing ion fluence. Plan view TEM images show the formation of clusters in the irradiated DLC films. HRTEM micrographs from the samples irradiated at a fluence of 5×1015 ions/cm 2 show the lattice image with an average interplanar spacing of 0.34 nm, revealing that the clusters are graphite clusters. The crystallographic planes in these clusters are somewhat distorted compared to the perfect graphite structure.

  12. Damage Profiles and Ion Distribution in Pt-irradiated SiC

    SciTech Connect

    Xue, Haizhou; Zhang, Yanwen; Zhu, Zihua; Zhang, Weiming; Bae, Dr. In-Tae; Weber, William J

    2012-01-01

    Single crystalline 6H-SiC samples were irradiated at 150 K using 2MeV Pt ions. Local volume swelling is determined by electron energy loss spectroscopy (EELS), a nearly sigmoidal dependence with irradiation dose is observed. The disorder profiles and ion distribution are determined by Rutherford backscattering spectrometry (RBS), transmission electron microscopy and secondary ion mass spectrum. Since the volume swelling reaches 12% over the damage region under high ion fluence, lattice expansion is considered and corrected during the data analysis of RBS spectra to obtain depth profiles. Projectile and damage profiles are estimated by SRIM (Stopping and Range of Ions in Matter). Comparing with the measured profiles, SRIM code significantly overestimates the electronic stopping power for the slow heavy Pt ions, and large derivations are observed in the predicted ion distribution and the damage profiles. Utilizing the reciprocity method that is based on the invariance of the inelastic excitation in ion atom collisions against interchange of projectile and target, much lower electronic stopping is deduced. A simple approach based on reducing the density of SiC target in SRIM simulation is proposed to compensate the overestimated SRIM electronic stopping power values. Better damage profile and ion range are predicted.

  13. Evaluation of surface damage on organic materials irradiated with Ar cluster ion beam

    SciTech Connect

    Yamamoto, Y.; Ichiki, K.; Ninomiya, S.; Matsuo, J.; Seki, T.; Aoki, T.

    2011-01-07

    The sputtering yields of organic materials under large cluster ion bombardment are much higher than those under conventional monomer ion bombardment. The sputtering rate of arginine remains constant with fluence for an Ar cluster ion beam, but decreases with fluence for Ar monomer. Additionally, because Ar cluster etching induces little damage, Ar cluster ion can be used to achieve molecular depth profiling of organic materials. In this study, we evaluated the damage to poly methyl methacrylate (PMMA) and arginine samples irradiated with Ar atomic and Ar cluster ion beams. Arginine samples were analyzed by secondary ion mass spectrometry (SIMS) and PMMA samples were analyzed by X-ray photoelectron spectroscopy (XPS). The chemical structure of organic materials remained unchanged after Ar cluster irradiation, but was seriously damaged. These results indicated that bombardment with Ar cluster ions induced less surface damage than bombardment with Ar atomic ion. The damage layer thickness with 5 keV Ar cluster ion bombardment was less than 1 nm.

  14. Damage Profiles and Ion Distribution in Pt-irradiated SiC

    SciTech Connect

    Xue, Haizhou; Zhang, Yanwen; Zhu, Zihua; Zhang, Weiming; Bae, In-Tae; Weber, William J.

    2012-09-01

    Single crystalline 6H-SiC samples were irradiated at 150 K with 2 MeV Pt ions. The local volume swelling was determined by electron energy loss spectroscopy (EELS), and a nearly sigmoidal dependence on irradiation dose is observed. The disorder profiles and ion distribution were determined by Rutherford backscattering spectrometry (RBS), transmission electron microscopy, and secondary ion mass spectrometry. Since the volume swelling reaches 12% over the damage region at high ion fluence, the effect of lattice expansion is considered and corrected for in the analysis of RBS spectra to obtain depth profiles. Projectile and damage profiles are estimated by SRIM (Stopping and Range of Ions in Matter).When compared with the measured profiles, the SRIM code predictions of ion distribution and the damage profiles are underestimated due to significant overestimation of the electronic stopping power for the slow heavy Pt ions. By utilizing the reciprocity method, which is based on the invariance of the inelastic energy loss in ion-solid collisions against interchange of projectile and target atom, a much lower electronic stopping power is deduced. A simple approach, based on reducing the density of SiC target in SRIM simulation, is proposed to compensate the overestimated SRIM electronic stopping power values, which results in improved agreement between predicted and measured damage profiles and ion ranges.

  15. Energy dependence of Ge amorphization by Ne, Ar or Kr ion irradiation

    SciTech Connect

    Birtcher, R.C.

    1994-10-01

    Ge has been irradiated at RT by Ne, Ar, or Kr ions of different energies, and the doses required for complete amorphization determined by in situ TEM and electron diffraction. Onset of amorphization was detected after the lowest ion doses reflecting amorphization by individual ions. The ion dose required for complete amorphization increased nearly linearly with ion energy over the range 0.5 to 3.5 MeV for all ions. Amorphization cross sections have been determined for all ions and energies used. The displacements per atom required for complete amorphization decreased with ion energy or mass, owing to decrease in radiation annealing of amorphous volumes as a result of a decrease in fraction of low energy transfers to Ge atoms. Increasing the relative fraction low energy transfers to Ge atoms by simultaneous 1 MeV electron irradiation increased the Kr ion dose required for complete amorphization by as much as a factor of 2.5. The effect is believed to be due to an increase in the fraction of freely migrating defects produced by low energy transfers to Ge atoms.

  16. Evaluation of surface damage on organic materials irradiated with Ar cluster ion beam

    NASA Astrophysics Data System (ADS)

    Yamamoto, Y.; Ichiki, K.; Ninomiya, S.; Seki, T.; Aoki, T.; Matsuo, J.

    2011-01-01

    The sputtering yields of organic materials under large cluster ion bombardment are much higher than those under conventional monomer ion bombardment. The sputtering rate of arginine remains constant with fluence for an Ar cluster ion beam, but decreases with fluence for Ar monomer. Additionally, because Ar cluster etching induces little damage, Ar cluster ion can be used to achieve molecular depth profiling of organic materials. In this study, we evaluated the damage to poly methyl methacrylate (PMMA) and arginine samples irradiated with Ar atomic and Ar cluster ion beams. Arginine samples were analyzed by secondary ion mass spectrometry (SIMS) and PMMA samples were analyzed by X-ray photoelectron spectroscopy (XPS). The chemical structure of organic materials remained unchanged after Ar cluster irradiation, but was seriously damaged. These results indicated that bombardment with Ar cluster ions induced less surface damage than bombardment with Ar atomic ion. The damage layer thickness with 5 keV Ar cluster ion bombardment was less than 1 nm.

  17. Shape manipulation of ion irradiated Ag nanoparticles embedded in lithium niobate

    NASA Astrophysics Data System (ADS)

    Wolf, Steffen; Rensberg, Jura; Johannes, Andreas; Thomae, Rainer; Smit, Frederick; Neveling, Retief; Moodley, Mathew; Bierschenk, Thomas; Rodriguez, Matias; Afra, Boshra; Hasan, Shakeeb Bin; Rockstuhl, Carsten; Ridgway, Mark; Bharuth-Ram, Krish; Ronning, Carsten

    2016-04-01

    Spherical silver nanoparticles were prepared by means of ion beam synthesis in lithium niobate. The embedded nanoparticles were then irradiated with energetic 84Kr and 197Au ions, resulting in different electronic energy losses between 8.1 and 27.5 keV nm-1 in the top layer of the samples. Due to the high electronic energy losses of the irradiating ions, molten ion tracks are formed inside the lithium niobate in which the elongated Ag nanoparticles are formed. This process is strongly dependent on the initial particle size and leads to a broad aspect ratio distribution. Extinction spectra of the samples feature the extinction maximum with shoulders on either side. While the maximum is caused by numerous remaining spherical nanoparticles, the shoulders can be attributed to elongated particles. The latter could be verified by COMSOL simulations. The extinction spectra are thus a superposition of the spectra of all individual particles.

  18. Transformation of multi walled carbon nanotubes irradiated by swift heavy ions

    NASA Astrophysics Data System (ADS)

    Vishalli; Avasthi, D. K.; Srivastava, Alok; Dharamvir, Keya

    2017-09-01

    The radiation stability of multiwalled carbon nanotube (MWCNT) buckypaper (BP) has been studied under extreme conditions. Samples of thick mat of MWCNT, called buckypaper, have been prepared by vacuum filtration method and were irradiated by 120 MeV Au ions with fluences ranging from 3 × 1011 ions/cm2 to 5 × 1013 ions/cm2. The samples were characterized by Field Emission Scanning Electron Microscopy (FESEM), High Resolution Transmission Electron Microscopy (HRTEM) and Raman spectroscopy. The surface imaging studies indicate the decrease in the average diameter of nanotubes under ion irradiation due to the sputtering of atoms from the CNT surface. Raman studies demonstrate initial healing at lower fluence, defect production at higher fluences and amorphization at highest fluence.

  19. Effects of Plasma-Ion Irradiation on Structures and Properties of Carbon Nanotubes

    NASA Astrophysics Data System (ADS)

    Hatakeyama, Rikizo

    2009-10-01

    Nanocarbons of carbon allotropes have drawn great attention due to their high potential for unique properties and a variety of applications. Since carbon nanotubes among them are furnished with one-dimensional hollow inner-nanospaces, various kinds of atoms and molecules are possible to be injected into the nanospaces based on plasma nanotechnology, which could lead to innovative functionalization of the pristine ones. For that purpose original approaches using nanoscopic plasma processing mainly in ionic plasmas have been performed in order to develop SWNT(single-walled carbon nanotube)-, and DWNT(double-walled carbon nanotube)-based materials with novel functions corresponding to nano electronic and biological applications, where positive and negative ions with their energies and fluxes controlled are irradiated to immersed substrates coated with the pristine carbon nanotubes. Consequently, we have innovatively created various kinds of charge-/spin-exploited atoms and molecules encapsulated SWNTs and DWNTs. Finally, their electronic, magnetic, and optical properties are intensively investigated using a configuration of field effect transistor (FET) and a SQUID magnetometer. As a result, we have for the first time realized air-stable semi-conducting pn control, formed nano structures with magnetic semiconductor and ultimate air-stable nano pn-junctions, found distinct characteristics of negative differential resistance, and observed photoinduced electron transfer phenomena upon the encapsulated SWNTs and DWNTs.

  20. Microstructural evolution of CANDU spacer material Inconel X-750 under in situ ion irradiation

    NASA Astrophysics Data System (ADS)

    Zhang, He Ken; Yao, Zhongwen; Judge, Colin; Griffiths, Malcolm

    2013-11-01

    Work on Inconel®Inconel® is a registered trademark of Special Metals Corporation that refers to a family of austenitic nickel-chromium-based superalloys.1 X-750 spacers removed from CANDU®CANDU® is a registered trademark of Atomic Energy of Canada Limited standing for ''CANada Deuterium Uranium''.2 reactors has shown that they become embrittled and there is development of many small cavities within the metal matrix and along grain boundaries. In order to emulate the neutron irradiation induced microstructural changes, heavy ion irradiations (1 MeV Kr2+ ions) were performed while observing the damage evolution using an intermediate voltage electron microscope (IVEM) operating at 200 kV. The irradiations were carried out at various temperatures 60-400 °C. The principal strengthening phase, γ‧, was disordered at low doses (˜0.06 dpa) during the irradiation. M23C6 carbides were found to be stable up to 5.4 dpa. Lattice defects consisted mostly of stacking fault tetrahedras (SFTs), 1/2<1 1 0> perfect loops and small 1/3<1 1 1> faulted Frank loops. The ratio of SFT number density to loop number density for each irradiation condition was found to be neither temperature nor dose dependent. Under the operation of the ion beam the SFT production was very rapid, with no evidence for further growth once formed, indicating that they probably formed as a result of cascade collapse in a single cascade. The number density of the defects was found to saturate at low dose (˜0.68 dpa). No cavities were observed regardless of the irradiation temperature between 60 °C and 400 °C for doses up to 5.4 dpa. In contrast, cavities have been observed after neutron irradiation in the same material at similar doses and temperatures indicating that helium, produce during neutron irradiation, may be essential for the nucleation and growth of cavities.

  1. Metastable phases in Zr-Excel alloy and their stability under heavy ion (Kr2+) irradiation

    NASA Astrophysics Data System (ADS)

    Yu, Hongbing; Zhang, Ken; Yao, Zhongwen; Kirk, Mark A.; Long, Fei; Daymond, Mark R.

    2016-02-01

    Zr-Excel alloy (Zr-3.5Sn-0.8Nb-0.8Mo, wt.%) has been proposed as a candidate material of pressure tubes in the CANDU-SCWR design. It is a dual-phase alloy containing primary hcp α-Zr and metastable bcc β-Zr. Metastable hexagonal ω-Zr phase could form in β-Zr as a result of aging during the processing of the tube. A synchrotron X-ray study was employed to study the lattice properties of the metastable phases in as-received Zr-Excel pressure tube material. In situ heavy ion (1 MeV Kr2+) irradiations were carried out at 200 °C and 450 °C to emulate the stability of the metastable phase under a reactor environment. Quantitative Chemi-STEM EDS analysis was conducted on both un-irradiated and irradiated samples to investigate alloying element redistribution induced by heavy ion irradiation. It was found that no decomposition of β-Zr was observed under irradiation at both 200 °C and 450 °C. However, ω-Zr particles experienced shape changes and shrinkage associated with enrichment of Fe at the β/ω interface during 200 °C irradiation but not at 450 °C. There is a noticeable increase in the level of Fe in the α matrix after irradiation at both 200 °C and 450 °C. The concentrations of Nb, Mo and Fe are increased in the ω phase but decreased in the β phase at 200 °C. The stability of metastable phases under heavy ion irradiation associated with elemental redistribution is discussed.

  2. Fluidity and supercriticality of the QCD matter created in relativistic heavy ion collisions

    SciTech Connect

    Liao Jinfeng; Koch, Volker

    2010-01-15

    In this paper we discuss the fluidity of the hot and dense QCD matter created in ultrarelativistic heavy ion collisions in comparison with various other fluids and, in particular, suggest its possible supercriticality. After examining the proper way to compare nonrelativistic and relativistic fluids from both thermodynamic and hydrodynamic perspectives, we propose a new fluidity measure that shows certain universality for a remarkable diversity of critical fluids. We then demonstrate that a fluid in its supercritical regime has its fluidity considerably enhanced. This result may suggest a possible relationship between the seemingly good fluidity of the QCD matter produced in heavy ion collisions at a center-of-mass energy of sq root(s)=200A GeV and the supercriticality of this matter with respect to the critical end point on the QCD phase diagram. Based on this observation, we predict an even better fluidity of the matter to be created in heavy ion collisions at Large Hadron Collider energies and the loss of good fluidity at certain, lower beam energy. Finally, based on our criteria, we analyze the suitability of a hydrodynamic description for the fireball evolution in heavy ion collisions at various energies.

  3. Ion Irradiation of Asphaltite: Optical Effects and Implications for Trans-Neptunian Objects and Centaurs

    NASA Astrophysics Data System (ADS)

    Moroz, L. V.; Baratta, G.; Distefano, E.; Strazzulla, G.; Starukhina, L. V.; Dotto, E.; Barucci, M. A.

    2003-06-01

    Trans-Neptunian Objects (TNOs) and Centaurs show remarkable colour variations in the visual and near-infrared spectral regions. Surface alteration processes such as space weathering (e.g., bombardment with ions) and impact resurfacing may play an important role in the colour diversity of such bodies. Ion irradiation of hydrocarbon ices and their mixtures with water ice transforms neutral (grey) surface colours of ices to red and further to grey. Along with the ices, TNOs and Centaurs probably contain complex carbonaceous compounds, in particular, complex hydrocarbons. Unlike ices, such refractory organic materials have originally low visual albedos and red colours in the visible and near-infrared ranges. Here we present the first results of ion irradiation experiments on asphaltite. Asphaltite is a natural complex hydrocarbon material. The reflectance spectra of asphaltite in the 0.4-0.8 μm range have been recorded before irradiation and after each irradiation step. We demonstrate that irradiation of this red dark material with 30 keV H+ and 15 keV N+ ions gradually transforms its colour from red to grey as a result of carbonization. A moderate increase in the visual albedo has been observed. These results may imply that the surfaces of primitive red objects optically dominated by complex refractory organics may show a similar space weathering trend. Our laboratory results were compared with published colours of TNOs and Centaurs. A broad variety of spectral colours observed for TNOs and Centaurs may be reproduced by various spectra of irradiated organics corresponding to different ion fluences. However, such objects probably also contain ices and silicate components which show different space weathering trends. This fact, together with a lack of information about albedos, may explain difficulties to reveal correlations between surface colours within TNO and Centaur populations and their other properties, such as absolute magnitudes and orbital parameters.

  4. Tuning the surface properties of hydrogel at the nanoscale with focused ion irradiation.

    PubMed

    Kim, Y; Abuelfilat, A Y; Hoo, S P; Al-Abboodi, A; Liu, B; Ng, Tuck; Chan, P; Fu, J

    2014-11-14

    With the site-specific machining capability of Focused Ion Beam (FIB) irradiation, we aim to tailor the surface morphology and physical attributes of biocompatible hydrogel at the nano/micro scale particularly for tissue engineering and other biomedical studies. Thin films of Gtn-HPA/CMC-Tyr hydrogels were deposited on a gold-coated substrate and were subjected to irradiation with a kiloelectronvolt (keV) gallium ion beam. The sputtering yield, surface morphology and mechanical property changes were investigated using Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM) and Monte Carlo simulations. The sputtering yield of the hydrogel was found to be approximately 0.47 μm(3) nC(-1) compared with Monte-Carlo simulation results of 0.09 μm(3) nC(-1). Compared to the surface roughness of the pristine hydrogel at approximately 2 nm, the average surface roughness significantly increased with the increase of ion fluence with measurements extended to 20 nm at 100 pC μm(-2). Highly packed submicron porous patterns were also revealed with AFM, while significantly decreased pore sizes and increased porosity were found with ion irradiation at oblique incidence. The Young's modulus of irradiated hydrogel determined using AFM force spectroscopy was revealed to be dependent on ion fluence. Compared to the original Young's modulus value of 20 MPa, irradiation elevated the value to 250 MPa and 350 MPa at 1 pC μm(-2) and 100 pC μm(-2), respectively. Cell culture studies confirmed that the irradiated hydrogel samples were biocompatible, and the generated nanoscale patterns remained stable under physiological conditions.

  5. Irradiation effects in rapidly and conventionally solidified alloys. Phase stability in rapidly solidified N i-Nb under Ni ion irradiation

    NASA Technical Reports Server (NTRS)

    1982-01-01

    Two alloy compositions in the Ni-Nb system (Ni60Nb40 and Ni85Nb15) were produced by rapidly quenching from the melt with the piston anvil technique. The Ni60Nb40 was transformed to a metastable, partially crystalline state by heat treatment in a differential scanning calorimeter. The Ni85Nb15 was fully crystalline, with the majority of the grains composed of collections of primary dendrite arms. Both compositions were irradiated with 4 MeV Ni++ ions. The irradiation induced microstructures were examined by transmission electron microscopy and compared with thermally aged samples. The thermal evolution was arrested by ion irradiation in the temperature range studied, by inhibiting the nucleation of the NiNb phase. No irradiation induced voids were observed. It is found that the ion irradiation drives the microstructure along a different path than thermal evolution.

  6. Visualization of air and metal inhomogeneities in phantoms irradiated by carbon ion beams using prompt secondary ions.

    PubMed

    Gaa, T; Reinhart, M; Hartmann, B; Jakubek, J; Soukup, P; Jäkel, O; Martišíková, M

    2017-06-01

    Non-invasive methods for monitoring of the therapeutic ion beam extension in the patient are desired in order to handle deteriorations of the dose distribution related to changes of the patient geometry. In carbon ion radiotherapy, secondary light ions represent one of potential sources of information about the dose distribution in the irradiated target. The capability to detect range-changing inhomogeneities inside of an otherwise homogeneous phantom, based on single track measurements, is addressed in this paper. Air and stainless steel inhomogeneities, with PMMA equivalent thickness of 10mm and 4.8mm respectively, were inserted into a PMMA-phantom at different positions in depth. Irradiations of the phantom with therapeutic carbon ion pencil beams were performed at the Heidelberg Ion Beam Therapy Center. Tracks of single secondary ions escaping the phantom under irradiation were detected with a pixelized semiconductor detector Timepix. The statistical relevance of the found differences between the track distributions with and without inhomogeneities was evaluated. Measured shifts of the distal edge and changes in the fragmentation probability make the presence of inhomogeneities inserted into the traversed medium detectable for both, 10mm air cavities and 1mm thick stainless steel. Moreover, the method was shown to be sensitive also on their position in the observed body, even when localized behind the Bragg-peak. The presented results demonstrate experimentally, that the method using distributions of single secondary ion tracks is sensitive to the changes of homogeneity of the traversed material for the studied geometries of the target. Copyright © 2017 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

  7. Activated Ion Electron Capture Dissociation (AI ECD) of proteins: synchronization of infrared and electron irradiation with ion magnetron motion.

    PubMed

    Mikhailov, Victor A; Cooper, Helen J

    2009-05-01

    Here, we show that to perform activated ion electron capture dissociation (AI-ECD) in a Fourier transform ion cyclotron resonance (FT-ICR) mass spectrometer equipped with a CO(2) laser, it is necessary to synchronize both infrared irradiation and electron capture dissociation with ion magnetron motion. This requirement is essential for instruments in which the infrared laser is angled off-axis, such as the Thermo Finnigan LTQ FT. Generally, the electron irradiation time required for proteins is much shorter (ms) than that required for peptides (tens of ms), and the modulation of ECD, AI ECD, and infrared multiphoton dissociation (IRMPD) with ion magnetron motion is more pronounced. We have optimized AI ECD for ubiquitin, cytochrome c, and myoglobin; however the results can be extended to other proteins. We demonstrate that pre-ECD and post-ECD activation are physically different and display different kinetics. We also demonstrate how, by use of appropriate AI ECD time sequences and normalization, the kinetics of protein gas-phase refolding can be deconvoluted from the diffusion of the ion cloud and measured on the time scale longer than the period of ion magnetron motion.

  8. Thermal cycling and high power density hydrogen ion beam irradiation of tungsten layers on tungsten substrate

    NASA Astrophysics Data System (ADS)

    Airapetov, A. A.; Begrambekov, L. B.; Gretskaya, I. Yu; Grunin, A. V.; Dyachenko, M. Yu; Puntakov, N. A.; Sadovskiy, Ya A.

    2016-09-01

    Tungsten layers with iron impurity were deposited on tungsten substrates modeling re-deposited layers in a fusion device. The samples were tested by thermocycling and hydrogen ion beam tests. Thermocycling revealed globule formation on the surface. The size of the globules depended on iron impurity content in the coating deposited. Pore formation was observed which in some cases lead to exfoliation of the coatings. Hydrogen ion irradiation lead to formation of blisters on the coating and finally its exfoliation.

  9. Characterization of microstructure in hydrogen ion irradiated vanadium at room temperature and the microstructural evolution during post-irradiation annealing

    SciTech Connect

    Gao, Jin; Cui, Lijuan; Wan, Farong

    2016-01-15

    The microstructure of pure vanadium after hydrogen ion irradiation at room temperature to a fluence of 1 × 10{sup 17} ions/cm{sup 2} (and 5 × 10{sup 16} ions/cm{sup 2}) was investigated by transmission electron microscopy (TEM). Small dislocation loops (black spots) and cavities are formed after the irradiation. The nature and Burgers vector of dislocation loops formed in vanadium was characterized using g·b technique and inside–outside method. Interstitial dislocation loops with Burgers vector of 1/2 < 111 > predominantly formed with less than 10% of 1/2 < 110 > type. No < 100 > type or vacancy type dislocation loop formed. The microstructural evolution during the annealing process was also studied. Density and size of dislocation loops changed sharply when the annealing temperature was lifted up to 450 °C. When the annealing temperature was higher than 500 °C, bubble coalescence occurred with some large hydrogen bubbles formed. - Highlights: • Interstitial dislocation loops with Burgers vector of 1/2<111> were predominant. • Less than 10% of 1/2<110> dislocation loops were present in pure vanadium. • No <100> or vacancy type loops were present in pure vanadium. • Density and size of dislocation loops changed sharply at temperature above 450 °C. • Bubble coalescence occurred when annealing temperature was higher than 500 °C.

  10. Effect of ion irradiation and indentation depth on the kinetics of deformation during micro-indentation of Zr-2.5%Nb pressure tube material at 25 °C

    NASA Astrophysics Data System (ADS)

    Bose, B.; Klassen, R. J.

    2010-04-01

    Micro-indentation creep tests were performed at 25 °C on radial-normal samples cut from Zr-2.5Nb CANDU pressure tube material in both the as-fabricated condition and after irradiation with 8.5 MeV Zr + ions. The average indentation stress, and hence the yield stress, was found to increase with decreasing indentation depth and with increasing levels of ion irradiation. The activation energy of the indentation creep rate and hence the, activation energy of the obstacles that limit the rate of dislocation glide, was independent of indentation depth but increased from Δ G0 = 0.185 to 0.215 μb 3 with increasing ion irradiation damage. The magnitude of the activation energy indicates that ion irradiation introduces a new type of obstacle into the microstructure which reduces the low temperature indentation creep rate of Zr-2.5Nb pressure tubes. This is supported by TEM images showing that Zr + ion irradiation produces small, nanometer size, dislocation loops which act as obstacles to dislocation glide and thus influence both the yield stress and the activation energy of the low-temperature thermal creep of Zr-2.5Nb pressure tube material. These findings suggest that neutron irradiation will have similar effect upon yield stress and low-temperature thermal creep as the Zr + ion irradiation since both create similar crystallographic defects in Zr-2.5Nb pressure tubes.

  11. Short communication on "In-situ TEM ion irradiation investigations on U3Si2 at LWR temperatures"

    DOE PAGES

    Miao, Yinbin; Harp, Jason; Mo, Kun; ...

    2016-11-21

    Here, the radiation-induced amorphization of U3Si2 was investigated by in-situ transmission electron microscopy using 1 MeV Kr ion irradiation. Both arc-melted and sintered U3Si2 specimens were irradiated at room temperature to confirm the similarity in their responses to radiation. The sintered specimens were then irradiated at 350 °C and 550 °C up to 7.2 × 1015 ions/cm2 to examine their amorphization behavior under light water reactor (LWR) conditions. U3Si2 remains crystalline under irradiation at LWR temperatures. Oxidation of the material was observed at high irradiation doses.

  12. Short Communication on "In-situ TEM ion irradiation investigations on U3Si2 at LWR temperatures"

    NASA Astrophysics Data System (ADS)

    Miao, Yinbin; Harp, Jason; Mo, Kun; Bhattacharya, Sumit; Baldo, Peter; Yacout, Abdellatif M.

    2017-02-01

    The radiation-induced amorphization of U3Si2 was investigated by in-situ transmission electron microscopy using 1 MeV Kr ion irradiation. Both arc-melted and sintered U3Si2 specimens were irradiated at room temperature to confirm the similarity in their responses to radiation. The sintered specimens were then irradiated at 350 °C and 550 °C up to 7.2 × 1015 ions/cm2 to examine their amorphization behavior under light water reactor (LWR) conditions. U3Si2 remains crystalline under irradiation at LWR temperatures. Oxidation of the material was observed at high irradiation doses.

  13. Silicon ion irradiation effects on the magnetic properties of ion beam synthesized CoPt phase

    SciTech Connect

    Balaji, S.; Amirthapandian, S.; Panigrahi, B. K.; Mangamma, G.; Kalavathi, S.; Gupta, Ajay; Nair, K. G. M.

    2012-06-05

    Ion beam mixing of Pt/Co bilayers using self ion (Pt{sup +}) beam results in formation of CoPt phase. Upon ion beam annealing the ion mixed samples using 4 MeV Si{sup +} ions at 300 deg. C, diffusion of Co towards the Pt/Co interface is observed. The Si{sup +} ion beam rotates the magnetization of the CoPt phase from in plane to out of plane of the film.

  14. Evolution of Crystallinity and Texturing on 120 MeV Au Ion Irradiation on NiO Thin Films

    SciTech Connect

    Mallick, P.; Rath, Chandana; Agarwal, D. C.; Avasthi, D. K.; Kanjilal, D.; Biswal, R.; Mishra, N. C.; Behera, D.; Satyam, P. V.

    2008-10-23

    NiO thin films grown on Si(100) substrate by electron beam evaporation and sintered at 500 deg. C and 700 deg. C were irradiated with 120 MeV {sup 197}Au{sup 9+} ions. The FCC structure of the sintered films was retained up to the highest fluence (3 x l0{sup 13} ions.cm{sup -2}) of irradiation. As against the expected amorphization due to ion irradiation when electronic energy loss exceeds certain threshold value, we observe an improvement of crystallinity and grain orientation at certain fluences of irradiation.

  15. Atomistic modeling of nanoscale patterning of L1{sub 2} order induced by ion irradiation

    SciTech Connect

    Ye Jia; Li Youhong; Averback, Robert; Zuo Jianmin; Bellon, Pascal

    2010-09-15

    Theoretical predictions indicate that ordered alloys can spontaneously develop a steady-state nanoscale microstructure when irradiated with energetic particles. This behavior derives from a dynamical competition between disordering in cascades and thermally activated reordering, which leads to self-organization of the chemical order parameter. We test this possibility by combining molecular dynamics (MD) and kinetic Monte Carlo (KMC) simulations. We first generate realistic distributions of disordered zones for Ni{sub 3}Al irradiated with 70 keV He and 1 MeV Kr ions using MD and then input this data into KMC to obtain predictions of steady state microstructures as a function of the irradiation flux. Nanoscale patterning is observed for Kr ion irradiations but not for He ion irradiations. We illustrate, moreover, using image simulations of these KMC microstructures, that high-resolution transmission electron microscopy can be employed to identify nanoscale patterning. Finally, we indicate how this method could be used to synthesize functional thin films, with potential for magnetic applications.

  16. Production and evolution of carbonaceous material by ion irradiation in space.

    PubMed

    Strazzulla, G; Baratta, G A; Spinella, F

    1995-03-01

    We review recent experimental studies concerning the evolution, driven by ion irradiation, of carbonaceous material from frozen gas to a refractory molecular solid. Under further irradiation the latter changes to a polymer-like material and ultimately to amorphous carbon. Most of the results have been obtained by "in situ" and remote IR and Raman spectroscopy. The results have been applied to demonstrate that molecular solids may be easily formed by irradiation of frozen mantles in dense interstellar clouds. Polymer-like material and amorphous carbons may result by further irradiation of organic mantles on grains in the diffuse interstellar medium. Those grains, during the aggregation to form extended bodies like comets (T-Tau phase of the Sun), are further modified. These latter are also irradiated, after the comet formation, during their long stay in the Oort cloud. In particular it has been suggested that comet may develop an ion-produced cometary organic crust that laboratory evidences show to be stable against temperature increases experienced during passages near the Sun. The comparison between the Raman spectra of some IDP (Interplanetary Dust Particles) and the Raman spectra of some ion-produced amorphous carbons, is also discussed.

  17. Characterization the microstructure and defects of matrix graphite irradiated with Xe ions

    NASA Astrophysics Data System (ADS)

    Xu, H. X.; Lin, J.; Li, J. J.; Zhu, Z. Y.; Zeng, G. L.; Liu, J. D.; Gu, B. C.; Liu, B.

    2017-09-01

    The matrix graphite of pebble fuel elements was irradiated with 1 MeV Xe ions at room temperature to fluences of 5.8 × 1014 ions/cm2 and 2.9 × 1015 ions/cm2, respectively. The microstructure and defects of matrix graphite samples were characterized by using scanning electron microscopy (SEM), Raman spectroscopy and slow positron beam techniques. The SEM result reveals that hundred-nanometer sized pores appear at the surface after irradiation and the density of pore increases with fluence. Raman results show that D peak (1350 cm-1) and G peak (1580 cm-1) are broadened after irradiation. In addition, the G peak position shifts from 1580 cm-1 to 1560 cm-1 with the linewidth increases from 21 cm-1 to 132 cm-1, corresponding to the increase in bond-angle disorder as the matrix graphite transforms from microcrystalline to amorphous carbon(a-C). The slow positron beam study shows that the defects-trapped positron S parameter increases with fluence, suggesting that the vacancy-type defects concentration or size of open volume defects increases. The analysis of Raman and slow positron beam consistently conclude that the reason for the phase transition after irradiation is the increase in irradiation-induced vacancy defects accompanied by the overlap of disordered regions.

  18. Overview of the US-Japan collaborative investigation on hydrogen isotope retention in neutron-irradiated and ion-damaged tungsten

    SciTech Connect

    Masashi Shimada; Y. Hatano; Y. Oya; T. Oda; M. Hara; G. Cao; M. Kobayashi; M. Sokolov; H. Watanabe; B. Tyburska; Y. Ueda; P. Calderoni

    2011-09-01

    Plasma-facing components (PFCs) will be exposed to 14 MeV neutrons from deuterium-tritium (D-T) fusion reactions, and tungsten, a candidate PFC for the divertor in ITER, is expected to receive a neutron dose of 0.7 displacement per atom (dpa) by the end of operation in ITER. The effect of neutron-irradiation damage has been mainly simulated using high-energy ion bombardment. While this prior database of results is quite valuable for understanding the behavior of hydrogen isotopes in PFCs, it does not encompass the full range of effects that must be considered in a practical fusion environment due to short penetration depth, damage gradient, high damage rate, and high PKA energy spectrum of the ion bombardment. In addition, neutrons change the elemental composition via transmutations, and create a high radiation environment inside PFCs, which influence the behavior of hydrogen isotope in PFCs, suggesting the utilization of fission reactors is necessary for neutron irradiation. Therefore, the effort to correlate among high-energy ions, fission neutrons, and fusion neutrons is crucial for accurately estimating tritium retention under a neutron-irradiation environment. Under the framework of the US-Japan TITAN program, tungsten samples (99.99 at. % purity from A.L.M.T. Co.) were irradiated by neutron in the High Flux Isotope Reactor (HFIR), ORNL, at 50 and 300C to 0.025, 0.3, and 1.2 dpa, and the investigation of deuterium retention in neutron-irradiation was performed in the INL Tritium Plasma Experiment (TPE), the unique high-flux linear plasma facility that can handle tritium, beryllium and activated materials. This paper reports the recent results from the comparison of ion-damaged tungsten via various ion species (2.8 MeV Fe2+, 20 MeV W2+, and 700 keV H-) with that from neutron-irradiated tungsten to identify the similarities and differences among them.

  19. Kr implantation into heavy ion irradiated monolithic U-Mo/Al systems: SIMS and SEM investigations

    NASA Astrophysics Data System (ADS)

    Zweifel, T.; Valle, N.; Grygiel, C.; Monnet, I.; Beck, L.; Petry, W.

    2016-03-01

    Worldwide, high performance research and material test reactors are aiming to convert their fuel from high enriched uranium towards low enriched ones. High density U-Mo/Al based nuclear fuels are considered as a promising candidate for this conversion. However, during in-pile test irradiations, the formation of an interdiffusion layer (IDL) between the U-Mo and the Al matrix is observed, caused by irradiation enhanced U-Al interdiffusion processes. This IDL accumulates fission gases at the IDL/matrix interfaces. Together, these two effects strongly reduce the performance of this new fuel type. Recently, the out-of-pile technique of heavy ion irradiation (127I) on U-Mo/Al layer systems proved to be an alternative to time-consuming in-pile test irradiations for certain fuel behaviour aspects. Here we present SIMS and SEM investigations of non-conventional 82Kr implantation into previously heavy ion irradiated U-Mo/Al layer systems. It is shown that Kr accumulates inside μm large porosities at the IDL/matrix interfaces. This critical accumulation of μm-sized large gas bubbles is directly related to the presence of the irradiation induced IDL. Without IDL no critical accumulation of fission gas bubbles occurs.

  20. TEM in situ micropillar compression tests of ion irradiated oxide dispersion strengthened alloy

    NASA Astrophysics Data System (ADS)

    Yano, K. H.; Swenson, M. J.; Wu, Y.; Wharry, J. P.

    2017-01-01

    The growing role of charged particle irradiation in the evaluation of nuclear reactor candidate materials requires the development of novel methods to assess mechanical properties in near-surface irradiation damage layers just a few micrometers thick. In situ transmission electron microscopic (TEM) mechanical testing is one such promising method. In this work, microcompression pillars are fabricated from a Fe2+ ion irradiated bulk specimen of a model Fe-9%Cr oxide dispersion strengthened (ODS) alloy. Yield strengths measured directly from TEM in situ compression tests are within expected values, and are consistent with predictions based on the irradiated microstructure. Measured elastic modulus values, once adjusted for the amount of deformation and deflection in the base material, are also within the expected range. A pillar size effect is only observed in samples with minimum dimension ≤100 nm due to the low inter-obstacle spacing in the as received and irradiated material. TEM in situ micropillar compression tests hold great promise for quantitatively determining mechanical properties of shallow ion-irradiated layers.

  1. Etching yields and surface reactions of amorphous carbon by fluorocarbon ion irradiation

    NASA Astrophysics Data System (ADS)

    Karahashi, Kazuhiro; Li, Hu; Yamada, Kentaro; Ito, Tomoko; Numazawa, Satoshi; Machida, Ken; Ishikawa, Kiyoshi; Hamaguchi, Satoshi

    2017-06-01

    Etching yields of amorphous carbon (a-C) have been determined for Ar+, Ne+, F+, CF+, and CF3 + ion irradiation as functions of ion incident energy in the range from 300 to 2,000 eV. Amorphous carbon is often used as a hard mask material for reactive ion etching (RIE) of Si-based materials and its durability against chemically reactive etching is of primary importance. In this study, experiments on the ion-beam etching of a-C films were performed with a mass-selected ion beam system, which irradiated a sample surface with a single ion species at a specified incident energy under ultra high vacuum conditions. It is found that the etching yield of a-C can be strongly enhanced by the chemical effects of fluorine (F) contained in the incident ions over the corresponding physical sputtering yield. The yield data also show that the etching yield of a-C by fluorocarbon ions depends more sensitively on the amount of fluorine supplied to the surface than those of Si-based materials such as Si, SiO2, and Si3N4. Therefore, to minimize the erosion of a-C mask structures in an etching process for Si-based materials by fluorocarbon plasmas, one must optimize the fluorine content in the etching gas while maintaining sufficiently large etching rates for Si-based materials to be etched.

  2. Surface patterning of GaAs under irradiation with very heavy polyatomic Au ions

    NASA Astrophysics Data System (ADS)

    Bischoff, L.; Böttger, R.; Heinig, K.-H.; Facsko, S.; Pilz, W.

    2014-08-01

    Self-organization of surface patterns on GaAs under irradiation with heavy polyatomic Au ions has been observed. The patterns depend on the ion mass, and the substrate temperature as well as the incidence angle of the ions. At room temperature, under normal incidence the surface remains flat, whereas above 200 °C nanodroplets of Ga appear after irradiation with monatomic, biatomic as well as triatomic Au ions of kinetic energies in the range of 10-30 keV per atom. In the intermediate temperature range of 100-200 °C meander- and dot-like patterns form, which are not related to Ga excess. Under oblique ion incidence up to 45° from the surface normal, at room temperature the surface remains flat for mon- and polyatomic Au ions. For bi- and triatomic ions in the range of 60° ≤ α ≤ 70° ripple patterns have been found, which become shingle-like for α ≥ 80°, whereas the surface remains flat for monatomic ions.

  3. A comparison of lower and higher LET heavy ion irradiation effects on silicon NPN rf power transistors

    NASA Astrophysics Data System (ADS)

    Bharathi, M. N.; Pushpa, N.; Vinayakprasanna, N. H.; Prakash, A. P. Gnana

    2016-06-01

    The Silicon NPN rf power transistors were irradiated with 180 MeV Au14+ and 150 MeV Ag12+ ions in the dose range of 1 Mrad to 100 Mrad. The SRIM simulation was used to understand the energy loss and range of these ions in the transistor structure. The different electrical parameters such as Gummel characteristics, excess base current (∆IB), dc current gain (hFE), transconductance (gm), displacement damage factor (K) and output characteristics were studied systematically before and after irradiation. These results were compared with lower linear energy transfer (LET) ions such as 50 MeV Li3+, 95 MeV O7+, 100 MeV F8+, 140 MeV Si10+ and 175 MeV Ni13+ ions in the same dose range. The degradation for 180 MeV Au14+ and 150 MeV Ag12+ ion irradiated transistors was significantly more when compared to lower LET ions, indicating that the transistors are vulnerable to higher LET ion irradiations. Isochronal annealing study was conducted on the irradiated transistors to analyze the recovery in different electrical parameters. After isochronal annealing, the recovery in hFE and other electrical parameters was around 67% for Ag12+ ion irradiated transistors and 60% for Au14+ ion irradiated transistors.

  4. The effect of Argon ion irradiation on the thickness and structure of ultrathin amorphous carbon films

    NASA Astrophysics Data System (ADS)

    Xie, J.; Komvopoulos, K.

    2016-03-01

    Carbon films synthesized by plasma-enhanced chemical vapor deposition (PECVD) and filtered cathodic vacuum arc (FCVA) exhibit a layered structure consisting of a bottom (interface) and a top (surface) layer rich in sp2 atomic carbon bonding and a middle (bulk) layer of much higher sp3 content. Because of significant differences in the composition, structure, and thickness of these layers, decreasing the film thickness may negatively affect its properties. In this study, transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS) were used to examine the effect of Ar+ ion irradiation on the structure and thickness of ultrathin films of hydrogenated amorphous carbon (a-C:H) and hydrogen-free amorphous carbon (a-C) deposited by PECVD and FCVA, respectively. The TEM and EELS results show that 2-min ion irradiation decreases the film thickness without markedly changing the film structure and composition, whereas 4-min ion irradiation results in significant film thinning and a moderate decrease of the sp3 content of the bulk layer. This study demonstrates that Ar+ ion irradiation is an effective post-deposition process for reducing the thickness and tuning the structure of ultrathin carbon films. This capability has direct implications in the synthesis of ultrathin protective carbon overcoats for extremely high-density magnetic recording applications.

  5. The effect of Argon ion irradiation on the thickness and structure of ultrathin amorphous carbon films

    SciTech Connect

    Xie, J.; Komvopoulos, K.

    2016-03-07

    Carbon films synthesized by plasma-enhanced chemical vapor deposition (PECVD) and filtered cathodic vacuum arc (FCVA) exhibit a layered structure consisting of a bottom (interface) and a top (surface) layer rich in sp{sup 2} atomic carbon bonding and a middle (bulk) layer of much higher sp{sup 3} content. Because of significant differences in the composition, structure, and thickness of these layers, decreasing the film thickness may negatively affect its properties. In this study, transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS) were used to examine the effect of Ar{sup +} ion irradiation on the structure and thickness of ultrathin films of hydrogenated amorphous carbon (a-C:H) and hydrogen-free amorphous carbon (a-C) deposited by PECVD and FCVA, respectively. The TEM and EELS results show that 2-min ion irradiation decreases the film thickness without markedly changing the film structure and composition, whereas 4-min ion irradiation results in significant film thinning and a moderate decrease of the sp{sup 3} content of the bulk layer. This study demonstrates that Ar{sup +} ion irradiation is an effective post-deposition process for reducing the thickness and tuning the structure of ultrathin carbon films. This capability has direct implications in the synthesis of ultrathin protective carbon overcoats for extremely high-density magnetic recording applications.

  6. Carbon Ion Irradiation Inhibits Glioma Cell Migration Through Downregulation of Integrin Expression

    SciTech Connect

    Rieken, Stefan; Habermehl, Daniel; Wuerth, Lena; Brons, Stephan; Mohr, Angela; Lindel, Katja; Weber, Klaus; Haberer, Thomas; Debus, Juergen; Combs, Stephanie E.

    2012-05-01

    Purpose: To investigate the effect of carbon ion irradiation on glioma cell migration. Methods and Materials: U87 and Ln229 glioma cells were irradiated with photons and carbon ions. Migration was analyzed 24 h after irradiation. Fluorescence-activated cell sorting analysis was performed in order to quantify surface expression of integrins. Results: Single photon doses of 2 Gy and 10 Gy enhanced {alpha}{sub {nu}}{beta}{sub 3} and {alpha}{sub {nu}}{beta}{sub 5} integrin expression and caused tumor cell hypermigration on both vitronectin (Vn) and fibronectin (Fn). Compared to integrin expression in unirradiated cells, carbon ion irradiation caused decreased integrin expression and inhibited cell migration on both Vn and Fn. Conclusion: Photon radiotherapy (RT) enhances the risk of tumor cell migration and subsequently promotes locoregional spread via photon induction of integrin expression. In contrast to photon RT, carbon ion RT causes decreased integrin expression and suppresses glioma cell migration on both Vn and Fn, thus promising improved local control.

  7. Shaping of Au nanoparticles embedded in various layered structures by swift heavy ion beam irradiation

    NASA Astrophysics Data System (ADS)

    Dawi, E. A.; ArnoldBik, W. M.; Ackermann, R.; Habraken, F. H. P. M.

    2016-10-01

    We present a novel method to extend the ion-beam induced shaping of metallic nanoparticles in various layered structures. Monodisperse Au nanoparticles having mean diameter of 30 nm and their ion-shaping process is investigated for a limited number of experimental conditions. Au nanoparticles were embedded within a single plane in various layered structures of silicon nitride films (Si3N4), combinations of oxide-nitride films (SiO2-Si3N4) and amorphous silicon films (a-Si) and have been sequentially irradiated at 300 K at normal incidence with 50 and 25 MeV Ag ions, respectively. Under irradiation with heavy Ag ions and with sequential increase of the irradiation fluence, the evolution of the Au peak derived from the Rutherford Backscattering Spectrometry show broadening in Au peak, which indicates that the Au becomes distributed over a larger depth region, indicative of the elongation of the nanoparticles. The latter is observed almost for every layer structure investigated except for Au nanoparticles embedded in pure a-Si matrix. The largest elongation rate at all fluences is found for the Au nanoparticles encapsulated in pure Si3N4 films. For all irradiation energy applied, we again demonstrate the existence of both threshold and saturation fluences for the elongation effects mentioned.

  8. Microstructural response of InGaN to swift heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Zhang, L. M.; Jiang, W.; Fadanelli, R. C.; Ai, W. S.; Peng, J. X.; Wang, T. S.; Zhang, C. H.

    2016-12-01

    A monocrystalline In0.18Ga0.82N film of ∼275 nm in thickness grown on a GaN/Al2O3 substrate was irradiated with 290 MeV 238U32+ ions to a fluence of 1.2 × 1012 cm-2 at room temperature. The irradiated sample was characterized using helium ion microscopy (HIM), Rutherford backscattering spectrometry under ion-channeling conditions (RBS/C), and high-resolution X-ray diffraction (HRXRD). The irradiation leads to formation of ion tracks throughout the thin In0.18Ga0.82N film and the 3.0 μm thick GaN buffer layer. The mean diameter of the tracks in In0.18Ga0.82N is ∼9 nm, as determined by HIM examination. Combination of the HIM and RBS/C data suggests that the In0.18Ga0.82N material in the track is likely to be highly disordered or fully amorphized. The irradiation induced lattice relaxation in In0.18Ga0.82N and a distribution of d-spacing of the (0 0 0 2) planes in GaN with lattice expansion are observed by HRXRD.

  9. In-situ Study of Nanostructure and Electrical Resistance of Nanocluster Films Irradiated with Ion Beams

    SciTech Connect

    Jiang, Weilin; Sundararajan, Jennifer A.; Varga, Tamas; Bowden, Mark E.; Qiang, You; McCloy, John S.; Henager, Charles H.; Montgomery, Robert O.

    2014-08-11

    An in-situ study is reported on the structural evolution in nanocluster films under He+ ion irradiation using an advanced helium ion microscope. The films consist of loosely interconnected nanoclusters of magnetite or iron-magnetite (Fe-Fe3O4) core-shells. The nanostructure is observed to undergo dramatic changes under ion-beam irradiation, featuring grain growth, phase transition, particle aggregation, and formation of nanowire-like network and nano-pores. Studies based on ion irradiation, thermal annealing and election irradiation have indicated that the major structural evolution is activated by elastic nuclear collisions, while both electronic and thermal processes can play a significant role once the evolution starts. The electrical resistance of the Fe-Fe3O4 films measured in situ exhibits a super-exponential decay with dose. The behavior suggests that the nanocluster films possess an intrinsic merit for development of an advanced online monitor for neutron radiation with both high detection sensitivity and long-term applicability, which can enhance safety measures in many nuclear operations.

  10. In situ observation of the ultrafast lattice dynamics of graphite under ion irradiation

    NASA Astrophysics Data System (ADS)

    Ishioka, Kunie; Hase, Muneaki; Kitajima, Masahiro

    2004-05-01

    We develop a pump-probe experiment system, in which vibrational dynamics of a solid sample under ion irradiation can be measured in real time. In situ observation enables us to monitor small changes induced by ion irradiation, without being influenced by the irreproducibility of the sample quality or the experimental configuration. We apply the experimental system to investigate the femtosecond dynamics of the coherent E2 g1 phonon of graphite under 5 keV He + irradiation. A slight decrease in the dephasing rate of the phonon at the initial stage, as well as a downshift followed by an upshift of the phonon frequency, are clearly demonstrated, all of which were ambiguous in the ex situ experiment due to the poor reproducibility of the surface quality. This technique could also be applied to study femtosecond vibrational dynamics in real time during thermal annealing, film deposition with e.g. ablation and sputter, and molecular adsorption on substrates.

  11. Particle Accelerator Applications: Ion and Electron Irradiation in Materials Science, Biology and Medicine

    SciTech Connect

    Rodriguez-Fernandez, Luis

    2010-09-10

    Although the developments of particle accelerators are devoted to basic study of matter constituents, since the beginning these machines have been applied with different purposes in many areas also. Today particle accelerators are essential instruments for science and technology. This work presents an overview of the main application for direct particle irradiation with accelerator in material science, biology and medicine. They are used for material synthesis by ion implantation and charged particle irradiation; to make coatings and micromachining; to characterize broad kind of samples by ion beam analysis techniques; as mass spectrometers for atomic isotopes determination. In biomedicine the accelerators are applied for the study of effects by charged particles on cells. In medicine the radiotherapy by electron irradiation is widely used, while hadrontherapy is still under development. Also, they are necessary for short life radioisotopes production required in radiodiagnostic.

  12. Effect of swift heavy ion irradiation on optical absorption properties of SWCNTs

    SciTech Connect

    Vishalli, Dharamvir, Keya; Raina, K. K.; Avasthi, D. K.; Srivastava, Alok

    2016-05-06

    In the present work, experimental investigations on the optical absorption properties of swift heavy ion irradiated single walled carbon nanotubes (SWCNTs) have been carried out. The uniform thin films of SWCNTs have been deposited on quartz substrate by Langmuir Blodgett (LB) method in a layer by layer manner. The irradiation of thin films is carried out by nickel ion beam of energy 60 MeV at different fluences. The variation in the S{sub 11}, S{sub 22}, and M{sub 11} band in optical spectra of SWCNTs has been studied before and after irradiation. The decrease in intensity/area of the bands corresponding to both semiconducting and metallic SWCNTs has been observed with increasing fluence.

  13. Ion irradiation of icy mixtures: synthesis of molecules relevant to astrochemistry and astrobiology

    NASA Astrophysics Data System (ADS)

    Strazzulla, G.; Baratta, G. A.; Brucato, J. R.; Ioppolo, S.; Palumbo, M. E.; Spinella, F.

    2007-08-01

    In the last years many experimental results have been obtained by our as well as other groups on the chemical and physical changes induced by ion irradiation and UV photolysis of frozen mixtures of simple molecules with a view to their astrophysical relevance. The presence in space of complex organic molecules of astrochemical and even astrobiological relevance is revealed by mm and sub-mm observations. Many of those molecules are however thought to be formed by energetic processing of icy mantles on interstellar grains that occasionally (e.g. in the circumstellar region of a new-born star) warm-up and release molecules in the gas phase. Here we present some recent results concerning: • The formation of formamide, a molecule particularly relevant to astrobiology, produced by ion irradiation of frozen mixtures containing water, methane and nitrogen. • The formation of sub-oxides after irradiation of CO-rich icy mixtures.

  14. Particle Accelerator Applications: Ion and Electron Irradiation in Materials Science, Biology and Medicine

    NASA Astrophysics Data System (ADS)

    Rodríguez-Fernández, Luis

    2010-09-01

    Although the developments of particle accelerators are devoted to basic study of matter constituents, since the beginning these machines have been applied with different purposes in many areas also. Today particle accelerators are essential instruments for science and technology. This work presents an overview of the main application for direct particle irradiation with accelerator in material science, biology and medicine. They are used for material synthesis by ion implantation and charged particle irradiation; to make coatings and micromachining; to characterize broad kind of samples by ion beam analysis techniques; as mass spectrometers for atomic isotopes determination. In biomedicine the accelerators are applied for the study of effects by charged particles on cells. In medicine the radiotherapy by electron irradiation is widely used, while hadrontherapy is still under development. Also, they are necessary for short life radioisotopes production required in radiodiagnostic.

  15. MeV H+ ion irradiation effect on the stoichiometry of polyethylene terephthalate films

    NASA Astrophysics Data System (ADS)

    Abdesselam, M.; Muller, D.; Djebara, M.; Ouichaoui, S.; Chami, A. C.

    2013-07-01

    Appropriate experimental conditions have been chosen to investigate the influence of main H+ ion irradiation parameters on stoichiometry changes induced in polyethylene terephthalate (PET) thin films. Stacks of six self-supporting identical films were irradiated perpendicularly to the target surface. Thus, the irradiations were realized simultaneously at different values of the target electronic stopping power, ɛ+. Indeed, the initial H+ ion energy of 1.1 MeV incident on the front polymer film was degraded down to 0.48 MeV at the entrance of the rear stacked film, which corresponds to an increase of ɛ+ from ˜0.22 up to ˜0.41 MeV cm2 mg-1. Ion fluences in the range (0.05-4) × 1015 cm-2 corresponding to an ion dose interval 1.80-263 MGy were used. The (H, O, C) atomic surface densities of the PET polymeric films were quantitatively determined by IBA techniques using a 1.62 MeV deuteron beam leading to the following main results: for each target film stacked at a given position thus fixed ɛ+, the oxygen atomic density decreases linearly versus ion fluence, ϕ; for the different ɛ+, the hydrogen impoverishment of the PET target is insignificant below critical fluence ϕc ˜ 1.5 × 1015 cm-2 and becomes substantial above ϕc; for fixed ϕ, the hydrogen and oxygen atomic densities exhibit linear decreases versus ɛ+; all measured such data versus ϕ and ɛ+ merge together into a unique decreasing curve for each (H, O, C) polymer content element when represented in function of the H+ ion dose, D, tightly correlating the latter two parameters; the O content element release from the PET target appears to be the most important, followed by the H content depletion, while the target C content is least affected under H+ ion irradiation.

  16. Ion irradiation of the native oxide/silicon surface increases the thermal boundary conductance across aluminum/silicon interfaces

    NASA Astrophysics Data System (ADS)

    Gorham, Caroline S.; Hattar, Khalid; Cheaito, Ramez; Duda, John C.; Gaskins, John T.; Beechem, Thomas E.; Ihlefeld, Jon F.; Biedermann, Laura B.; Piekos, Edward S.; Medlin, Douglas L.; Hopkins, Patrick E.

    2014-07-01

    The thermal boundary conductance across solid-solid interfaces can be affected by the physical properties of the solid boundary. Atomic composition, disorder, and bonding between materials can result in large deviations in the phonon scattering mechanisms contributing to thermal boundary conductance. Theoretical and computational studies have suggested that the mixing of atoms around an interface can lead to an increase in thermal boundary conductance by creating a region with an average vibrational spectra of the two materials forming the interface. In this paper, we experimentally demonstrate that ion irradiation and subsequent modification of atoms at solid surfaces can increase the thermal boundary conductance across solid interfaces due to a change in the acoustic impedance of the surface. We measure the thermal boundary conductance between thin aluminum films and silicon substrates with native silicon dioxide layers that have been subjected to proton irradiation and post-irradiation surface cleaning procedures. The thermal boundary conductance across the Al/native oxide/Si interfacial region increases with an increase in proton dose. Supported with statistical simulations, we hypothesize that ion beam mixing of the native oxide and silicon substrate within ˜2.2nm of the silicon surface results in the observed increase in thermal boundary conductance. This ion mixing leads to the spatial gradation of the silicon native oxide into the silicon substrate, which alters the acoustic impedance and vibrational characteristics at the interface of the aluminum film and native oxide/silicon substrate. We confirm this assertion with picosecond acoustic analyses. Our results demonstrate that under specific conditions, a "more disordered and defected" interfacial region can have a lower resistance than a more "perfect" interface.

  17. Volatile evolution from polymer materials induced by irradiation with He ++ ions and comparative pyrolysis experiments

    NASA Astrophysics Data System (ADS)

    Murphy, J. J.; Patel, M.; Skinner, A. R.; Horn, I. M.; Powell, S. J.; Smith, P. F.

    2004-02-01

    Irradiation of polymer samples using an accelerated beam of He ++ ions passed through a 10 μm thick window of Havar foil has been performed. Such an irradiation simulates the effects of large α radiation doses on a vastly reduced time-scale. The experimental set up was designed so that the irradiated materials were contained within a small sample chamber. This chamber was isolated from the main vacuum chamber of the ion beam by means of the Havar foil window. A mass spectrometer linked directly to the sample chamber was used to analyse gaseous products evolved from the materials under irradiation. Samples of a material in which the polymer phase was an ethylenevinylacetate/polyvinylalcohol composite material indicated increased CO 2 and CO evolution upon irradiation. This material, however, evolved a considerable amount of volatiles even without irradiation and so a detailed mechanistic interpretation of the results is not possible. A foamed poly(siloxane) material evolved a number of volatile species upon irradiation and possible chemical degradation mechanisms are commented upon. The sample was extremely resistant to radiation induced degradation as measured by volatile evolution though, so again a detailed mechanistic analysis is not possible. Samples of a polyester based polyurethane evolved CO 2, CO and a number of high mass volatile species. Assignment of chemical structures to the main molecular ions allows deductions about the chemistry underlying radiation induced change to be made. Furthermore, identification of trends in volatile production allows information about potential degradation mechanisms to be deduced. To assess the contribution of sample heating on volatile evolution a series of pyrolysis experiments were performed. These indicate no evolution of volatiles below 100 °C and evolution of volatiles possessing masses of greater than 50 amu only at temperature of above 300 °C.

  18. Iron ion irradiation increases promotes adhesion of monocytic cells to arterial vascular endothelium

    NASA Astrophysics Data System (ADS)

    Kucik, Dennis; Khaled, Saman; Gupta, Kiran; Wu, Xing; Yu, Tao; Chang, Polly; Kabarowski, Janusz

    Radiation causes inflammation, and chronic, low-level vascular inflammation is a risk factor for atherosclerosis. Consistent with this, exposure to radiation from a variety of sources is associated with increased risk of heart disease and stroke. Part of the inflammatory response to radiation is a change in the adhesiveness of the endothelial cells that line the blood vessels, triggering inappropriate accumulation of leukocytes, leading to later, damaging effects of inflammation. Although some studies have been done on the effects of gamma irradiation on vascular endothelium, the response of endothelium to heavy ion radiation likely to be encountered in prolonged space flight has not been determined. We investigated how irradiation of aortic endothelial cells with iron ions affects adhesiveness of cultured aortic endothelial cells for monocytic cells and the consequences of this for development of atherosclerosis. Aortic endothelial cells were irradiated with 600 MeV iron ions at Brookhaven National Laboratory and adhesion-related changes were measured. Cells remained viable for at least 72 hours, and were even able to repair acute damage to cell junctions. We found that iron ion irradiation altered expression levels of specific endothelial cell adhesion molecules. Further, these changes had functional consequences. Using a flow chamber adhesion assay to measure adhesion of monocytic cells to endothelial cells under physiological shear stress, we found that adhesivity of vascular endothelium was enhanced in as little as 24 hours after irradiation. Further, the radiation dose dependence was not monotonic, suggesting that it was not simply the result of endothelial cell damage. We also irradiated aortic arches and carotid arteries of Apolipoprotein-E-deficient mice. Histologic analysis of these mice will be conducted to determine whether effects of radiation on endothelial adhesiveness result in consequences for development of atherosclerosis. (Supported by NSBRI

  19. Helium ion irradiation behavior of Ni-1wt.%SiCNP composite and the effect of ion flux

    NASA Astrophysics Data System (ADS)

    Zhou, X. L.; Huang, H. F.; Xie, R.; Thorogood, G. J.; Yang, C.; Li, Z. J.; Xu, H. J.

    2015-12-01

    Silicon carbide nanoparticle-reinforced nickel metal (Ni-SiCNP composite) samples were bombarded by helium ions with fluences of 1 × 1016 and 3 × 1016 ions/cm2 at two different fluxes. The microstructural and mechanical changes were characterized via TEM and nanoindentation. Nano-scaled helium bubbles in the shape of spheres were observed in the samples irradiated at high flux and polygons at low flux. The number of helium bubbles increased with the fluence, whereas their mean size remained unaffected. In addition, the nanohardness of the damage layer also increased as the fluence increased. In addition this study suggests that a higher flux results in a higher number of smaller helium bubbles, while showing no obvious effect on the irradiation-induced hardening of the materials.

  20. Alterations in adenylate ratios in plant cells after accelerated ion irradiation

    NASA Astrophysics Data System (ADS)

    Vasilenko, A.; Sidorenko, P. G.

    Levels of adenylate metabolism have been studied in cells of Nicotiana tabacum growing in vitro, and in root apex extracts of Pisum sativum irradiated at the 95-in. isochronous cyclotron U-240, Institute for Nuclear Research, Ukrainian National Academy of Sciences, Kyiv. Particle beams of accelerated helium ions with energy 9.34 keV/mum were used. Replacement and rapid freezing of the irradiated plant samples in liquid nitrogen were carried out with a manipulator and a remote control system. After doses of 5, 20, 50, and 100 Gy of gamma-irradiation, as well as 50 and 100 Gy ^4He irradiation, the cellular ATP/ADP ratio increased during early stages of the response. This effect was absent at higher doses and after exposure to sparsely-ionizing radiation, when a rapid decline in the cellular ATP concentration and the ATP/ADP ratio occurred.

  1. Formation and evolution of ripples on ion-irradiated semiconductor surfaces

    SciTech Connect

    Kang, M.; Wu, J. H.; Ye, W.; Jiang, Y.; Robb, E. A.; Chen, C.; Goldman, R. S.

    2014-02-03

    We have examined the formation and evolution of ripples on focused-ion-beam (FIB) irradiated compound semiconductor surfaces. Using initially normal-incidence Ga{sup +} FIB irradiation of InSb, we tuned the local beam incidence angle (θ{sub eff}) by varying the pitch and/or dwell time. For single-pass FIB irradiation, increasing θ{sub eff} induces morphological evolution from pits and islands to ripples to featureless surfaces. Multiple-pass FIB irradiation of the rippled surfaces at a fixed θ{sub eff} leads to island formation on the ripple crests, followed by nanorod (NR) growth. This ripple-NR transition provides an alternative approach for achieving dense arrays of NRs.

  2. Ion beam irradiation of embedded nanoparticles: Toward an in situ control of size and spatial distribution

    SciTech Connect

    Rizza, G.; Cheverry, H.; Gacoin, T.; Lamasson, A.; Henry, S.

    2007-01-01

    Irradiation of chemically synthesized Au nanoparticles embedded in a dielectric matrix promotes the formation of a halo of satellites around the original cluster. We show that the complete dissolution of the nanoparticles (NC) results in the formation of a narrow size distribution of small precipitates with a mean size of 2 nm and a standard deviation of 0.4 nm. By combining the chemical synthesis of the nanoparticles and the irradiation to induce their dissolution and precipitation, we give a guideline method for overcoming the difficulty of controlling the size and spatial distribution of the embedded NC associated with ion implantation technique. In particular, we showed that the irradiation can be used to tailor the size of the already formed NC. Moreover, we establish that the satellites cluster evolution under irradiation can be described by a two step process. These two steps are discussed in terms of classical and inverse Ostwald ripening mechanisms.

  3. Inactivation, DNA double strand break induction and their rejoining in bacterial cells irradiated with heavy ions

    NASA Technical Reports Server (NTRS)

    Schaefer, M.; Zimmermann, H.; Schmitz, C.

    1994-01-01

    Besides inactivation one of the major interests in our experiments is to study the primary damage in the DNA double strand breaks (DSB) after heavy ion irradiation. These damages lead not only to cell death but also under repair activities to mutations. In further experiments we have investigated the inactivation with two different strains of Deinococcus radiodurans (R1, Rec 30) and the induction of DSB as well as the rejoining of DSB in stationary cells of E. coli (strain B/r) irradiated with radiations of different quality. In the latter case irradiations were done so that the cell survival was roughly at the same level. We measured the DSB using the pulse field gelelectrophoresis which allows to separate between intact (circular) and damaged (linear) DNA. The irradiated cells were transferred to NB medium and incubated for different times to allow rejoining.

  4. Ion-Irradiation-Induced Ferromagnetism in Undoped ZnO Thin Films

    DTIC Science & Technology

    2013-01-01

    point of the Brillouin zone. The polar A1 and E1 modes and two nonpolar E2 modes (E high 2 and E low 2 ) are Raman active, while the B1 modes are...chemical bonds due to the collisions between ions and elec- trons [12,13] at high ion fluencies such as those used in our study (1012 and 1013 ions cm2...equilibrium point defects as a result of the electron–photon interactions and bond breaking that occurs during the irradiation process. Raman

  5. Impact of ion irradiation on the thermal, structural, and mechanical properties of metallic glasses

    SciTech Connect

    Mayr, S.G.

    2005-04-01

    The impact of ion-beam irradiation on the thermal, structural, and mechanical properties of metallic glasses is investigated using the model glass, CuTi, in molecular dynamics computer simulations. It is found that ion-beam bombardment successively modifies the compositional and structural order toward a universal steady state, which proves to be independent of the initial relaxation state and thermal history of the unirradiated sample. This is reflected by key materials properties, including enthalpy, structural and compositional short-range order, as well as Young's modulus and fracture behavior. The results are interpreted within the framework of competing dynamics, where radiation-induced plastic relaxation counteracts ion-beam disordering.

  6. Swift heavy ion irradiation induced electrical degradation in deca-nanometer MOSFETs

    NASA Astrophysics Data System (ADS)

    Ma, Yao; Yang, Zhimei; Gong, Min; Gao, Bo; Li, Yun; Lin, Wei; Li, Jinbo; Xia, Zhuohui

    2016-09-01

    In this work, degradation of the electrical characteristics of 65 nm nMOSFETs under swift heavy ion irradiation is investigated. It was found that a heavy ion can generate a localized region of physical damage (ion latent track) in the gate oxide. This is the likely cause for the increased gate leakage current and soft breakdown (SBD) then hard breakdown (HBD) of the gate oxide. Except in the case of HBD, the devices retain their functionality but with degraded transconductance. The degraded gate oxide exhibits early breakdown behavior compatible with the model of defect generation and percolation path formation in the percolation model.

  7. Precipitation behavior of AlxCoCrFeNi high entropy alloys under ion irradiation

    PubMed Central

    Yang, Tengfei; Xia, Songqin; Liu, Shi; Wang, Chenxu; Liu, Shaoshuai; Fang, Yuan; Zhang, Yong; Xue, Jianming; Yan, Sha; Wang, Yugang

    2016-01-01

    Materials performance is central to the satisfactory operation of current and future nuclear energy systems due to the severe irradiation environment in reactors. Searching for structural materials with excellent irradiation tolerance is crucial for developing the next generation nuclear reactors. Here, we report the irradiation responses of a novel multi-component alloy system, high entropy alloy (HEA) AlxCoCrFeNi (x = 0.1, 0.75 and 1.5), focusing on their precipitation behavior. It is found that the single phase system, Al0.1CoCrFeNi, exhibits a great phase stability against ion irradiation. No precipitate is observed even at the highest fluence. In contrast, numerous coherent precipitates are present in both multi-phase HEAs. Based on the irradiation-induced/enhanced precipitation theory, the excellent structural stability against precipitation of Al0.1CoCrFeNi is attributed to the high configurational entropy and low atomic diffusion, which reduces the thermodynamic driving force and kinetically restrains the formation of precipitate, respectively. For the multiphase HEAs, the phase separations and formation of ordered phases reduce the system configurational entropy, resulting in the similar precipitation behavior with corresponding binary or ternary conventional alloys. This study demonstrates the structural stability of single-phase HEAs under irradiation and provides important implications for searching for HEAs with higher irradiation tolerance. PMID:27562023

  8. Cross-sectional TEM Observations of Si Wafers Irradiated With Gas Cluster Ion Beams

    SciTech Connect

    Isogai, Hiromichi; Toyoda, Eiji; Senda, Takeshi; Izunome, Koji; Kashima, Kazuhiko; Toyoda, Noriaki; Yamada, Isao

    2006-11-13

    Irradiation by a Gas Cluster Ion Beam (GCIB) is a promising technique for precise surface etching and planarization of Si wafers. However, it is very important to understand the crystalline structure of Si wafers after GCIB irradiation. In this study, the near surface structure of a Si (100) wafer was analyzed after GCIB irradiation, using a cross-sectional transmission electron microscope (XTEM). Ar-GCIB, that physically sputters Si atoms, and SF6-GCIB, that chemically etches the Si surface, were both used. After GCIB irradiation, high temperature annealing was performed in a hydrogen atmosphere. From XTEM observations, the surface of a virgin Si wafer exhibited completely crystalline structures, but the existence of an amorphous Si and a transition layer was confirmed after GCIB irradiation. The thickness of amorphous layer was about 30 nm after Ar-GCIB irradiation at 30 keV. However, a very thin (< 5 nm) layer was observed when 30 keV SF6-GCIB was used. The thickness of the transition layer was the same both Ar and SF6-GCIB irradiation. After annealing, the amorphous Si and transition layers had disappeared, and a complete crystalline structure with an atomically smooth surface was observed.

  9. Precipitation behavior of AlxCoCrFeNi high entropy alloys under ion irradiation

    NASA Astrophysics Data System (ADS)

    Yang, Tengfei; Xia, Songqin; Liu, Shi; Wang, Chenxu; Liu, Shaoshuai; Fang, Yuan; Zhang, Yong; Xue, Jianming; Yan, Sha; Wang, Yugang

    2016-08-01

    Materials performance is central to the satisfactory operation of current and future nuclear energy systems due to the severe irradiation environment in reactors. Searching for structural materials with excellent irradiation tolerance is crucial for developing the next generation nuclear reactors. Here, we report the irradiation responses of a novel multi-component alloy system, high entropy alloy (HEA) AlxCoCrFeNi (x = 0.1, 0.75 and 1.5), focusing on their precipitation behavior. It is found that the single phase system, Al0.1CoCrFeNi, exhibits a great phase stability against ion irradiation. No precipitate is observed even at the highest fluence. In contrast, numerous coherent precipitates are present in both multi-phase HEAs. Based on the irradiation-induced/enhanced precipitation theory, the excellent structural stability against precipitation of Al0.1CoCrFeNi is attributed to the high configurational entropy and low atomic diffusion, which reduces the thermodynamic driving force and kinetically restrains the formation of precipitate, respectively. For the multiphase HEAs, the phase separations and formation of ordered phases reduce the system configurational entropy, resulting in the similar precipitation behavior with corresponding binary or ternary conventional alloys. This study demonstrates the structural stability of single-phase HEAs under irradiation and provides important implications for searching for HEAs with higher irradiation tolerance.

  10. Precipitation behavior of AlxCoCrFeNi high entropy alloys under ion irradiation.

    PubMed

    Yang, Tengfei; Xia, Songqin; Liu, Shi; Wang, Chenxu; Liu, Shaoshuai; Fang, Yuan; Zhang, Yong; Xue, Jianming; Yan, Sha; Wang, Yugang

    2016-08-26

    Materials performance is central to the satisfactory operation of current and future nuclear energy systems due to the severe irradiation environment in reactors. Searching for structural materials with excellent irradiation tolerance is crucial for developing the next generation nuclear reactors. Here, we report the irradiation responses of a novel multi-component alloy system, high entropy alloy (HEA) AlxCoCrFeNi (x = 0.1, 0.75 and 1.5), focusing on their precipitation behavior. It is found that the single phase system, Al0.1CoCrFeNi, exhibits a great phase stability against ion irradiation. No precipitate is observed even at the highest fluence. In contrast, numerous coherent precipitates are present in both multi-phase HEAs. Based on the irradiation-induced/enhanced precipitation theory, the excellent structural stability against precipitation of Al0.1CoCrFeNi is attributed to the high configurational entropy and low atomic diffusion, which reduces the thermodynamic driving force and kinetically restrains the formation of precipitate, respectively. For the multiphase HEAs, the phase separations and formation of ordered phases reduce the system configurational entropy, resulting in the similar precipitation behavior with corresponding binary or ternary conventional alloys. This study demonstrates the structural stability of single-phase HEAs under irradiation and provides important implications for searching for HEAs with higher irradiation tolerance.

  11. Optical Properties of Ar Ions Irradiated Nanocrystalline ZrC and ZrN Thin Films

    NASA Technical Reports Server (NTRS)

    Martin, C.; Miller, K. H.; Makino, H.; Craciun, D.; Simeone, D.; Craciun, V.

    2016-01-01

    Thin nanocrystalline ZrC and ZrN films (less than 400 nanometers), grown on (100) Si substrates at a substrate temperature of 500 degrees Centigrade by the pulsed laser deposition (PLD) technique, were irradiated by 800 kiloelectronvolts Ar ion irradiation with fluences from 1 times 10(sup 14) atoms per square centimeter up to 2 times 10(sup 15) atoms per square centimeter. Optical reflectance data, acquired from as-deposited and irradiated films, in the range of 500-50000 per centimeter (0.06–6 electronvolts), was used to assess the effect of irradiation on the optical and electronic properties. Both in ZrC and ZrN films we observed that irradiation affects the optical properties of the films mostly at low frequencies, which is dominated by the free carriers response. In both materials, we found a significant reduction in the free carriers scattering rate, i.e. possible increase in mobility, at higher irradiation flux. This is consistent with our previous findings that irradiation affects the crystallite size and the micro-strain, but it does not induce major structural changes.

  12. Amorphization and recrystallization of single-crystalline hydrogen titanate nanowires by N{sup +} ion irradiation

    SciTech Connect

    Behera, Akshaya K.; Bandyopadyay, Malay K.; Chatterjee, Shyamal; Facsko, Stefan; Das, Siddhartha

    2014-06-21

    We report on the phase transformation of hydrogen titanate (H{sub 2}Ti{sub 3}O{sub 7}) nanowires induced by 50 keV N{sup +} ion irradiation at room temperature with fluences of 1 × 10{sup 15} ions/cm{sup 2} and 1 × 10{sup 16} ions/cm{sup 2}, respectively. Using transmission electron microscopy, the internal structure of the ion irradiated nanowires is analyzed. At low fluence, a transformation from crystalline H{sub 2}Ti{sub 3}O{sub 7} to amorphous TiO{sub 2} is observed. However, at higher fluence, a remarkable crystalline-amorphous TiO{sub 2} core-shell structure is formed. At this higher fluence, the recrystallization occurs in the core of the nanowire and the outer layer remains amorphous. The phase transformation and formation of core-shell structure are explained using the thermal spike model, radiation enhanced diffusion, and classical theory of nucleation and growth under non-equilibrium thermodynamics. X-ray photoelectron spectroscopy and Raman scattering reveal further insight into the structure of the nanowires before and after ion irradiation.

  13. On-line Raman spectroscopy of calcite and malachite during irradiation with swift heavy ions

    NASA Astrophysics Data System (ADS)

    Dedera, Sebastian; Burchard, Michael; Glasmacher, Ulrich A.; Schöppner, Nicole; Trautmann, Christina; Severin, Daniel; Romanenko, Anton; Hubert, Christian

    2015-12-01

    A new on-line Raman System, which was installed at the M3-beamline at the UNILAC, GSI Helmholtzzentrum für Schwerionenforschung Darmstadt was used for first "in situ" spectroscopic measurements. Calcite and malachite samples were irradiated in steps between 1 × 109 and 1 × 1012 ions/cm2 with Au ions (calcite) and Xe ions (malachite) at an energy of 4.8 MeV/u. After irradiation, calcite revealed a new Raman band at 437 cm-1 and change of the full width at half maximum for the 1087 cm-1 Raman band. The Raman bands of malachite change significantly with increasing fluence. Up to a fluence of 7 × 1010 ions/cm2, all existing bands decrease in intensity. Between 8 × 1010 and 1 × 1011 ions/cm2 a broad Cu2O band between 110 and 220 cm-1 occurs, which superimposes the pre-existing Raman bands. Additionally, a new broad band between 1000 and 1750 cm-1 is formed, which is interpreted as a carbon coating. In contrast to the Cu2O band, the carbon band vanished when further irradiating the sample. The installations as well as first in situ measurements at room temperature are presented.

  14. Damage induced by helium ion irradiation in Fe-based metallic glass

    NASA Astrophysics Data System (ADS)

    Zhang, Xiaonan; Mei, Xianxiu; Zhang, Qi; Li, Xiaona; Qiang, Jianbing; Wang, Younian

    2017-07-01

    The changes in structure and surface morphology of metallic glasses Fe80Si7.43B12.57 and Fe68Zr7B25 before and after the irradiation of He ions with the energy of 300 keV were investigated, and were compared with that of the tungsten. The results show that after the He2+ irradiation, metallic glass Fe68Zr7B25 still maintained amorphous. While a small amount of metastable β-Mn type phase nanocrystals formed in metallic glass Fe80Si7.43B12.57 at the fluence of 4.0 × 1017ions/cm2 (19dpa). The nanocrystals transformed into α-Fe phase and tetragonal Fe2B phase as the fluence increased to 1.0 × 1018ions/cm2 (47dpa). Then the new orthogonal Fe3B phase and β-Mn type phase nanocrystals appeared when the fluence increased further, and the quantities of nanocrystals increased. Blisters and cracks appeared on the surface of tungsten under the irradiation fluence of 1.0 × 1018ions/cm2, however only when the fluence was up to 1.6 × 1018ions/cm2, could cracks and spalling appear on the surfaces of metallic glasses.

  15. Decomposition of solid amorphous hydrogen peroxide by ion irradiation

    SciTech Connect

    Loeffler, Mark J.; Teolis, Ben D.; Baragiola, Raul A.

    2006-03-14

    We present laboratory studies of the radiolysis of pure (97%) solid H{sub 2}O{sub 2} films by 50 keV H{sup +} at 17 K. Using UV-visible and infrared reflectance spectroscopies, a quartz-crystal microbalance, and a mass spectrometer, we measured the absolute concentrations of the H{sub 2}O, O{sub 2}, H{sub 2}O{sub 2}, and O{sub 3} products as a function of irradiation fluence. Ozone was identified by both UV and infrared spectroscopies and O{sub 2} from its forbidden transition in the infrared at 1550 cm{sup -1}. From the measurements we derive radiation yields, which we find to be particularly high for the decomposition of hydrogen peroxide; this can be explained by the occurrence of a chemical chain reaction.

  16. Tailoring molybdenum nanostructure evolution by low-energy He+ ion irradiation

    NASA Astrophysics Data System (ADS)

    Tripathi, J. K.; Novakowski, T. J.; Hassanein, A.

    2015-10-01

    Mirror-finished polished molybdenum (Mo) samples were irradiated with 100 eV He+ ions as a function of ion fluence (using a constant flux of 7.2 × 1020 ions m-2 s-1) at normal incidence and at 923 K. Mo surface deterioration and nanoscopic fiber-form filament ("Mo fuzz") growth evolution were monitored by using field emission (FE) scanning electron (SEM) and atomic force (AFM) microscopy studies. Those studies confirm a reasonably clean and flat surface, up to several micrometer scales along with a few mechanical-polishing-induced scratches. However, He+ ion irradiation deteriorates the surface significantly even at 2.1 × 1023 ions m-2 fluence (about 5 min. irradiation time) and leads to evolution of homogeneously populated ∼75-nm-long Mo nanograins having ∼8 nm intergrain width. The primary stages of Mo fuzz growth, i.e., elongated half-cylindrical ∼70 nm nanoplatelets, and encapsulated bubbles of 20-45 nm in diameter and preferably within the grain boundaries of sub-micron-sized grains, were observed after 1.3 × 1024 ions m-2 fluence irradiation. Additionally, a sequential enhancement in the sharpness, density, and protrusions of Mo fuzz at the surface with ion fluence was also observed. Fluence- and flux-dependent studies have also been performed at 1223 K target temperature (beyond the temperature window for Mo fuzz formation). At a constant fluence of 2.6 × 1024 ions m-2, 7.2 × 1020 ions m-2 s-1 flux generates a homogeneous layered and stacked nanodiscs of ∼70 nm diameter. On the other hand, 1.2 × 1021 ions m-2 s-1 flux generates a combination of randomly patched netlike nanomatrix networked structure, mostly with ∼105 nm nanostructure wall width, various-shaped pores, and self-organized nano arrays. While the observed netlike nanomatrix network structures for 8.6 × 1024 ions m-2 fluence (at a constant flux of 1.2 × 1021 ions m-2 s-1) is quite similar to those for 2.6 × 1024 ions m-2 fluence, the nanostructure wall width extends up to ∼45

  17. High electronic excitations and ion beam mixing effects in high energy ion irradiated Fe/Si multilayers

    SciTech Connect

    Bauer, P.; Dufour, C.; Jaouen, C.; Marchal, G.; Pacaud, J.; Grilhe, J.; Jousset, J.C.

    1997-01-01

    M{umlt o}ssbauer spectroscopy ({sup 57}Fe) shows evidence for mixing effects induced by electronic energy deposition in nanoscale Fe/Si multilayers irradiated with swift heavy ions. A decrease in the mixing efficiency with electronic stopping power is reported; a threshold is found, under which iron environment modifications no longer occur. The kinetics of Fe{endash}Si phase formation after irradiation suggests the existence of three regimes: (i) for high excitation levels, a magnetic amorphous phase is formed directly in the wake of the incoming ion and an almost complete mixing is reached at low fluence (10{sup 13} U/cm{sup 2}); (ii) for low excitation levels, a paramagnetic Si-rich amorphous phase is favored at the interface while crystalline iron subsists at high fluences; (iii) for intermediate excitation levels, saturation effects are observed and the formation rate of both magnetic and paramagnetic phases points to direct mixing in the ion wake but with a reduced track length in comparison to U irradiation. The measured interfacial mixing cross section induced by electronic energy deposition suggests that a thermal diffusion process is mainly involved in addition to damage creation. {copyright} {ital 1997 American Institute of Physics.}

  18. Mechanisms of nanorod growth on focused-ion-beam-irradiated semiconductor surfaces: Role of redeposition

    SciTech Connect

    Wu, J. H.; Goldman, R. S.

    2012-01-30

    We have examined the formation and evolution of irradiation-induced nanorod (NR) growth through a comparison of focused-ion-beam irradiation of InSb wafers and InSb/GaAs heterostructures. Above a critical ion dose, cone-shaped NRs capped with In islands form on both InSb surfaces. For InSb wafers, the NR base diameter increases with ion energy. In the case of InSb/GaAs heterostructures, as the milled depth approaches the InSb/GaAs interface, the cone-shaped NRs transition to capless NRs with a truncated cone shape. These results suggest a growth mechanism in which both the NR cap and body are supplied by redeposition of atoms sputtered from InSb.

  19. Positive ion emission from oxidized aluminum during ultraviolet excimer laser irradiation

    SciTech Connect

    Khan, Enamul; Langford, S. C.; Dickinson, J. T.

    2011-07-15

    We report quadrupole mass-selected time-of-flight measurements of positive ions from oxidized aluminum metal (and for comparison, single-crystal sapphire) during pulsed excimer laser irradiation at 193 and 248 nm. This work focuses on laser fluences well below onset of rapid etching or optical breakdown. By far the most intense emissions are due to Al{sup +}. On previously unexposed material, the ion kinetic energies are initially well above the photon energy, consistent with the ejection of Al{sup +} sorbed at surface electron traps. During prolonged irradiation, the emission intensities and kinetic energies gradually fall. Emission from patches of oxide would account for previous reports of laser-induced Al{sup +} emission from metallic aluminum surfaces cleaned by ion etching if patches of thin oxide were to survive the etching treatment.

  20. Investigating change of properties in gallium ion irradiation patterned single-layer graphene

    NASA Astrophysics Data System (ADS)

    Wang, Quan; Dong, Jinyao; Bai, Bing; Xie, Guoxin

    2016-10-01

    Besides its excellent physical properties, graphene promises to play a significant role in electronics with superior properties, which requires patterning of graphene for device integration. Here, we presented the changes in properties of single-layer graphene before and after patterning using gallium ion beam. Combined with Raman spectra of graphene, the scanning capacitance microscopy (SCM) image confirmed that a metal-insulator transition occurred after large doses of gallium ion irradiation. The changes in work function and Raman spectra of graphene indicated that the defect density increased as increasing the dose and a structural transition occurred during gallium ion irradiation. The patterning width of graphene presented an increasing trend due to the scattering influence of the impurities and the substrate.

  1. Damage profile examination on ion irradiated PEEK by 6Li doping and neutron depth profiling technique

    NASA Astrophysics Data System (ADS)

    Vacík, J.; Červená, J.; Hnatowicz, V.; Švorčík, V.; Kobayashi, Y.; Fink, D.; Klett, R.

    1998-05-01

    Depth structure of radiation damaged surface layer of poly(aryl-ether-ether ketone) (PEEK) a polymer was studied using doping with 6Li atoms combined with nondestructive neutron depth profiling (NDP) method. The PEEK foils were irradiated with 2 MeV O + ions up to a fluence of 6 × 10 14 ions/cm 2. The damage profiles in the samples were visualized by doping of the samples with 5 M LiCl water solution at room temperature (RT) for 22.5 h. The Li ions are trapped on ion-produced radiation defects and the Li depth profiles are determined by the NDP method. NDP experiments were performed before and after leaching of excess of lithium atoms from the samples in distilled water at RT for 2 h. The leaching leads to dramatic changes in the Li depth distribution which, at low ion fluences, is similar in shape to the electronic energy loss profile of 2 MeV O + ions. For the higher fluences double-peaked profile occurs, which indicates a competition between different degradation processes in ion irradiated polymer.

  2. Molecular dynamics simulation analysis of ion irradiation effects on plasma-liquid interface

    NASA Astrophysics Data System (ADS)

    Minagawa, Yudai; Shirai, Naoki; Uchida, Satoshi; Tochikubo, Fumiyoshi

    2013-09-01

    Nonthermal atmospheric plasmas are used in a wide range of fields because the high-density plasma can be easily irradiated to various substances such as solid, liquid, biological object and so on. On the other hand, the mechanisms of physical and chemical phenomena at the plasma-liquid interface are not well understood yet. To investigate the effects of ion impact from plasma on water surface, we analyzed behavior of liquid water by classical molecular dynamics simulation. Simulation system consists of an irradiation particle in gas phase and 2000 water molecules in liquid phase. O+ ion with 10 eV or 100 eV was impinged on the water surface. Ion impact induced increasing water temperature and ejection of water molecules. The averaged number of evaporated water molecules by ion impact is 0.6 molecules at 10 eV and 7.0 molecules at 100 eV. The maximum ion penetration depth was 1.14 nm at 10 eV and 2.75 nm at 100 eV. Ion entering into water disturbs the stable hydrogen bonding configurations between water molecules and gives energy to water molecules. Some water molecules rotated and moved by ion interaction impact on other water molecules one after another. When the water molecule near the surface received strongly repulsive force, it released into gas phase. This work was supported financially in part by a Grant-in-Aid for Scientific Research on Innovation Areas (No21110007) from MEXT, Japan.

  3. Degradation of HT9 under simultaneous ion beam irradiation and liquid metal corrosion

    NASA Astrophysics Data System (ADS)

    Frazer, D.; Qvist, S.; Parker, S.; Krumwiede, D. L.; Caro, M.; Tesmer, J.; Maloy, S. A.; Wang, Y. Q.; Hosemann, P.

    2016-10-01

    A potentially promising coolant/structural material pair for a liquid-metal-cooled fast reactors is lead bismuth eutectic (LBE) coolant with the ferritic/martensitic steel HT9. The challenge of deploying LBE, however, is the corrosive environment it creates for structural materials. This corrosion can be mitigated with precise oxygen content control in the LBE to allow for the growth of passive protective oxide layers on the surface of the steel. In this paper, results are reported from the Irradiation Corrosion Experiment II (ICE-II), which allowed the simultaneous irradiation of a sample while in contact with LBE. It was found that a characteristic multilayer structure with an outer Fe3O4 oxide and inner FeCr2O4 spinel was grown and the oxidation was significantly larger in the irradiated region when compared to the region that was only exposed to LBE corrosion. Possible mechanisms are discussed to help understand this irradiation enhanced corrosion behavior.

  4. Irradiation effects of 12 eV oxygen ions on polyimide and fluorinated ethylene propylene

    NASA Astrophysics Data System (ADS)

    Majeed, R. M. A.; Purohit, V. S.; Bhoraskar, S. V.; Mandale, A. B.; Bhoraskar, V. N.

    2006-08-01

    Polyimide (PI) and Fluorinated Ethylene Propylene (FEP) samples (15mm x 15mm x 50 mu m ) were exposed to atomic oxygen ions of average energy similar to 12 eV and flux similar to 5x10(13) ions cm(-2) s(-1) , produced in the Electron Cyclotron Resonance (ECR) plasma. The energy and the flux of the oxygen ions at different positions in the plasma were measured by a retarding field analyzer. The fluence of the oxygen ions was varied from sample to sample in the range of similar to 5x10(16) to 2x10(17) ions cm(-2) by changing the irradiation period. The pre- and the post-irradiated samples were characterized by the weight loss, Scanning Electron Microscopy (SEM), X-ray Photoelectron Spectroscopy (XPS), and Fourier Transform Infrared (FTIR) techniques. The weight of the PI and FEP samples decreased with increasing the ion fluence. However, the erosion yield for the PI is found to be higher, by almost a factor five, when compared with that of FEP. On the surface region of irradiated samples, the concentrations of the carbon, fluorine, and oxygen and their corresponding chemical bonds have changed appreciably. Moreover, blisters and nanoglobules were also observed even at a fluence of similar to 10(17) ions cm(-2) . This oxygen ion fluence is almost two orders of magnitude lower than that of the 5 eV atomic oxygen, which a satellite encounters in the space, at the low Earth orbit, during its mission period of about 7 years.

  5. An in situ transmission electron microscopy study of the ion irradiation induced amorphisation of silicon by He and Xe

    DOE PAGES

    Edmondson, P. D.; Abrams, K. J.; Hinks, J. A.; ...

    2015-11-21

    We used transmission electron microscopy with in situ ion irradiation to examine the ion-beam-induced amorphisation of crystalline silicon under irradiation with light (He) and heavy (Xe) ions at room temperature. Analysis of the electron diffraction data reveal the heterogeneous amorphisation mechanism to be dominant in both cases. Moreover, for the differences in the amorphisation curves are discussed in terms of intra-cascade dynamic recovery, and the role of electronic and nuclear loss mechanisms.

  6. Photocurrent generation in lateral graphene p-n junction created by electron-beam irradiation

    PubMed Central

    Yu, Xuechao; Shen, Youde; Liu, Tao; Wu, Tao (Tom); Jie Wang, Qi

    2015-01-01

    Graphene has been considered as an attractive material for optoelectronic applications such as photodetectors owing to its extraordinary properties, e.g. broadband absorption and ultrahigh mobility. However, challenges still remain in fundamental and practical aspects of the conventional graphene photodetectors which normally rely on the photoconductive mode of operation which has the drawback of e.g. high dark current. Here, we demonstrated the photovoltaic mode operation in graphene p-n junctions fabricated by a simple but effective electron irradiation method that induces n-type doping in intrinsic p-type graphene. The physical mechanism of the junction formation is owing to the substrate gating effect caused by electron irradiation. Photoresponse was obtained for this type of photodetector because the photoexcited electron-hole pairs can be separated in the graphene p-n junction by the built-in potential. The fabricated graphene p-n junction photodetectors exhibit a high detectivity up to ~3 × 1010 Jones (cm Hz1/2 W−1) at room temperature, which is on a par with that of the traditional III–V photodetectors. The demonstrated novel and simple scheme for obtaining graphene p-n junctions can be used for other optoelectronic devices such as solar cells and be applied to other two dimensional materials based devices. PMID:26152225

  7. A coupled effect of nuclear and electronic energy loss on ion irradiation damage in lithium niobate

    DOE PAGES

    Liu, Peng; Zhang, Yanwen; Xue, Haizhou; ...

    2016-01-09

    Understanding irradiation effects induced by elastic energy loss to atomic nuclei and inelastic energy loss to electrons in a crystal, as well as the coupled effect between them, is a scientific challenge. Damage evolution in LiNbO3 irradiated by 0.9 and 21 MeV Si ions at 300 K has been studied utilizing Rutherford backscattering spectrometry in channeling mode. During the low-energy ion irradiation process, damage accumulation produced due to elastic collisions is described utilizing a disorder accumulation model. Moreover, low electronic energy loss is shown to induce observable damage that increases with ion fluence. For the same electronic energy loss, themore » velocity of the incident ion could affect the energy and spatial distribution of excited electrons, and therefore effectively modify the diameter of the ion track. Furthermore, nonlinear additive phenomenon of irradiation damage induced by high electronic energy loss in pre-damaged LiNbO3 has been observed. The result indicates that pre-existing damage induced from nuclear energy loss interacts synergistically with inelastic electronic energy loss to promote the formation of amorphous tracks and lead to rapid phase transformation, much more efficient than what is observed in pristine crystal solely induced by electronic energy loss. As a result, this synergistic effect is attributed to the fundamental mechanism that the defects produced by the elastic collisions result in a decrease in thermal conductivity, increase in the electron-phonon coupling, and further lead to higher intensity in thermal spike from intense electronic energy deposition along high-energy ion trajectory.« less

  8. A coupled effect of nuclear and electronic energy loss on ion irradiation damage in lithium niobate

    SciTech Connect

    Liu, Peng; Zhang, Yanwen; Xue, Haizhou; Jin, Ke; Crespillo, Miguel L.; Wang, Xuelin; Weber, William J.

    2016-01-09

    Understanding irradiation effects induced by elastic energy loss to atomic nuclei and inelastic energy loss to electrons in a crystal, as well as the coupled effect between them, is a scientific challenge. Damage evolution in LiNbO3 irradiated by 0.9 and 21 MeV Si ions at 300 K has been studied utilizing Rutherford backscattering spectrometry in channeling mode. During the low-energy ion irradiation process, damage accumulation produced due to elastic collisions is described utilizing a disorder accumulation model. Moreover, low electronic energy loss is shown to induce observable damage that increases with ion fluence. For the same electronic energy loss, the velocity of the incident ion could affect the energy and spatial distribution of excited electrons, and therefore effectively modify the diameter of the ion track. Furthermore, nonlinear additive phenomenon of irradiation damage induced by high electronic energy loss in pre-damaged LiNbO3 has been observed. The result indicates that pre-existing damage induced from nuclear energy loss interacts synergistically with inelastic electronic energy loss to promote the formation of amorphous tracks and lead to rapid phase transformation, much more efficient than what is observed in pristine crystal solely induced by electronic energy loss. As a result, this synergistic effect is attributed to the fundamental mechanism that the defects produced by the elastic collisions result in a decrease in thermal conductivity, increase in the electron-phonon coupling, and further lead to higher intensity in thermal spike from intense electronic energy deposition along high-energy ion trajectory.

  9. Photosynthetic Effect in Selenastrum capricornutum Progeny after Carbon-Ion Irradiation.

    PubMed

    Wang, Jie; Li, Xin; Lu, Dong; Du, Yan; Ma, Liang; Li, Wenjian; Chen, Jihong; Li, Fuli; Fan, Yong; Hu, Guangrong; Wang, Jufang

    2016-01-01

    A large proportion of mutants with altered pigment features have been obtained via exposure to heavy-ion beams, a technique that is efficient for trait improvement in the breeding of plants and algae. However, little is known about the underlying mechanisms by which the photosynthetic pigments are altered by heavy-ion irradiation. In our study, the photosynthetic characteristics of progenies from carbon-ion irradiated Selenastrum capricornutum were investigated. Five progenies deficient in chlorophyll a were isolated after carbon-ion exposure. Photosynthetic characteristics, photoprotection capacity and gene expression of the light-harvesting complex in these progenies were further characterized by the measurement of chlorophyll fluorescence parameters (Fv/Fm, ФPSII, NPQ, ETR), the de-epoxidation state of the xanthophyll cycle, the amount of lutein and quantitative real-time PCR. High maximum quantum yield of photosystem II at day 10 and high thermal dissipation ability were observed in progenies #23 and #37 under normal culture condition. Progenies #18, #19 and #20 showed stronger resistance against high levels of light steps than the control group (612-1077 μmol photons m -2 s -1, p< 0.05). The progenies #20 and #23 exhibited strong photoprotection by thermal dissipation and quenching of 3Chl* after 24 h of high light treatment. The mRNA levels of Lhcb5, Lhcbm5 and Lhcbm1 of the light-harvesting complex revealed markedly differential expression in the five progenies irradiated by carbon-ion beams. This work indicates that photosynthetic efficiency, photoprotection ability and the expression of light-harvesting antennae in unicellular green algae can be markedly influenced by irradiation. To our knowledge, this is the first report on changes in the photosynthetic pigments of green algae after treatment with carbon-ion beams.

  10. Photosynthetic Effect in Selenastrum capricornutum Progeny after Carbon-Ion Irradiation

    PubMed Central

    Wang, Jie; Li, Xin; Lu, Dong; Du, Yan; Ma, Liang; Li, Wenjian; Chen, Jihong; Li, Fuli; Fan, Yong; Hu, Guangrong; Wang, Jufang

    2016-01-01

    A large proportion of mutants with altered pigment features have been obtained via exposure to heavy-ion beams, a technique that is efficient for trait improvement in the breeding of plants and algae. However, little is known about the underlying mechanisms by which the photosynthetic pigments are altered by heavy-ion irradiation. In our study, the photosynthetic characteristics of progenies from carbon-ion irradiated Selenastrum capricornutum were investigated. Five progenies deficient in chlorophyll a were isolated after carbon-ion exposure. Photosynthetic characteristics, photoprotection capacity and gene expression of the light-harvesting complex in these progenies were further characterized by the measurement of chlorophyll fluorescence parameters (Fv/Fm, ФPSII, NPQ, ETR), the de-epoxidation state of the xanthophyll cycle, the amount of lutein and quantitative real-time PCR. High maximum quantum yield of photosystem II at day 10 and high thermal dissipation ability were observed in progenies #23 and #37 under normal culture condition. Progenies #18, #19 and #20 showed stronger resistance against high levels of light steps than the control group (612–1077 μmol photons m -2 s -1, p< 0.05). The progenies #20 and #23 exhibited strong photoprotection by thermal dissipation and quenching of 3Chl* after 24 h of high light treatment. The mRNA levels of Lhcb5, Lhcbm5 and Lhcbm1 of the light-harvesting complex revealed markedly differential expression in the five progenies irradiated by carbon-ion beams. This work indicates that photosynthetic efficiency, photoprotection ability and the expression of light-harvesting antennae in unicellular green algae can be markedly influenced by irradiation. To our knowledge, this is the first report on changes in the photosynthetic pigments of green algae after treatment with carbon-ion beams. PMID:26919351

  11. Reorientation of the crystalline planes in confined single crystal nickel nanorods induced by heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Misra, Abha; Tyagi, Pawan K.; Rai, Padmnabh; Misra, D. S.; Ghatak, Jay; Satyam, P. V.; Avasthi, D. K.

    2006-08-01

    In a recent letter Tyagi et al. [Appl. Phys. Lett. 86, 253110 (2005)] have reported the special orientation of nickel planes inside multiwalled carbon nanotubes (MWCNTs) with respect to the tube axis. Heavy ion irradiation has been performed with 1.5MeV Au2+ and 100MeV Au7+ ions on these nickel filled MWCNTs at fluences ranging from 1012to1015ions/cm2 at room temperature. Ion-induced modifications have been studied using high-resolution transmission electron microscopy. The diffraction pattern and the lattice imaging showed the presence of ion-induced planar defects on the tube walls and completely amorphized encapsulated nickel nanorods. The results are discussed in terms of thermal spike model.

  12. DLTS study of deep level defects in Li-ion irradiated bipolar junction transistor

    NASA Astrophysics Data System (ADS)

    Madhu, K. V.; Kulkarni, S. R.; Ravindra, M.; Damle, R.

    2007-01-01

    Commercial npn transistor (2N 2219A) irradiated with 50 MeV Li 3+-ions with fluences ranging from 3.1 × 10 13 ions cm -2 to 12.5 × 10 13 ions cm -2, is studied for radiation induced gain degradation and minority carrier trap levels or recombination centers. The properties such as activation energy, trap concentration and capture cross section of induced deep levels are studied by deep level transient spectroscopy (DLTS) technique. Minority carrier trap levels with energies ranging from 0.237 eV to 0.591 eV were observed in the base-collector junction of the transistor. In situ I- V measurements were made to study the gain degradation as a function of ion fluence. Ion induced energy levels result in increase in the base current through Shockley Read Hall (SRH) or multi-phonon recombination and subsequent transistor gain degradation.

  13. Tunneling current change of graphite surface by single ion irradiation

    SciTech Connect

    Ogiso, H. |; Mizutani, W.; Nakano, S.; Tokumoto, H.; Yamanaka, K.

    1997-12-01

    The authors discuss changes in electronic structure and the topography of a graphite surface undergoing by a single