How 60 Minutes ticked off Illinois Power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-04-01

A November 60 Minutes broadcast on CBS television asserting that costs are out of control at the Illinois Power Co's(IP) Clinton nuclear power project because of management incompetence triggered a series of rebuttals and counter-rebuttals. A review of the events and correspondence during the planning stage and after the broadcast explores the question of construction cost overruns and the economic impact the broadcast had on IP's investors, employees, and customers. A parallel filming by IP was aired to show how the CBS edited the interview with IP officials. IP personnel feel betrayed by what they consider misconceptions and errors inmore » the broadcast and are unhappy that an employee morale problem was worsened. Counter-arguments by both parties indicate a disagreement on both facts and interpretations. (DCK)« less

77 FR 31176 - Airworthiness Directives; Rolls-Royce plc (RR) Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-25

... currently requires inspecting the intermediate-pressure (IP) compressor rotor shaft rear balance land for... detect cracking on the IP compressor rotor rear balance land. IP compressor rotor rear balance land...), without sub-headings. Request To Delete the Re-Balance Requirement American Airlines requested that in the...

Interconnected porous hydroxyapatite ceramics for bone tissue engineering

PubMed Central

Yoshikawa, Hideki; Tamai, Noriyuki; Murase, Tsuyoshi; Myoui, Akira

2008-01-01

Several porous calcium hydroxyapatite (HA) ceramics have been used clinically as bone substitutes, but most of them possessed few interpore connections, resulting in pathological fracture probably due to poor bone formation within the substitute. We recently developed a fully interconnected porous HA ceramic (IP-CHA) by adopting the ‘foam-gel’ technique. The IP-CHA had a three-dimensional structure with spherical pores of uniform size (average 150 μm, porosity 75%), which were interconnected by window-like holes (average diameter 40 μm), and also demonstrated adequate compression strength (10–12 MPa). In animal experiments, the IP-CHA showed superior osteoconduction, with the majority of pores filled with newly formed bone. The interconnected porous structure facilitates bone tissue engineering by allowing the introduction of mesenchymal cells, osteotropic agents such as bone morphogenetic protein or vasculature into the pores. Clinically, we have applied the IP-CHA to treat various bony defects in orthopaedic surgery, and radiographic examinations demonstrated that grafted IP-CHA gained radiopacity more quickly than the synthetic HA in clinical use previously. We review the accumulated data on bone tissue engineering using the novel scaffold and on clinical application in the orthopaedic field. PMID:19106069

Performance Analysis of the Mobile IP Protocol (RFC 3344 and Related RFCS)

DTIC Science & Technology

2006-12-01

Encapsulation HMAC Keyed-Hash Message Authentication Code ICMP Internet Control Message Protocol IEEE Institute of Electrical and Electronics Engineers IETF...Internet Engineering Task Force IOS Internetwork Operating System IP Internet Protocol ITU International Telecommunication Union LAN Local Area...network computing. Most organizations today have sophisticated networks that are connected to the Internet. The major benefit reaped from such a

A Comparative Analysis between Direct and Indirect Measurement of Year I Integrated Project

ERIC Educational Resources Information Center

Abdullah, Siti Rozaimah Sheikh; Mohamad, Abu Bakar; Anuar, Nurina; Markom, Masturah; Ismail, Manal; Rosli, Masli Irwan; Hasan, Hassimi Abu

2013-01-01

The Integrated Project (IP) has been practised in the Department of Chemical and Process Engineering (JKKP) since the 2006/2007 session. Initially, the IP is only implemented for the Year II students for both Chemical (KK) and Biochemical Engineering (KB) programmes. Previously, the Year 1 curriculum was only based on the common faculty courses.…

Evaluation of Social Competencies in Chemical Engineering: Application and Results of the Pilot Test (Academic Year 2012-2013)

ERIC Educational Resources Information Center

Grande, Francisco José Suñé; Witt, Hans Jörg; Avalos, Josep Bonet

2015-01-01

The Escola Tècnica Superior d'Enginyeria Química has a long tradition in the deployment of social competencies in engineering curricula through Integrated Projects (IP) carried out in structured teams. Social competencies are taught and practiced during the development of the IPs. We conceptually introduce a methodology for a 360 degrees…

Titin Mutations in iPS cells Define Sarcomere Insufficiency as a Cause of Dilated Cardiomyopathy

PubMed Central

Hinson, John T.; Chopra, Anant; Nafissi, Navid; Polacheck, William J.; Benson, Craig C.; Swist, Sandra; Gorham, Joshua; Yang, Luhan; Schafer, Sebastian; Sheng, Calvin C.; Haghighi, Alireza; Homsy, Jason; Hubner, Norbert; Church, George; Cook, Stuart A.; Linke, Wolfgang A.; Chen, Christopher S.; Seidman, J. G.; Seidman, Christine E.

2015-01-01

Human mutations that truncate the massive sarcomere protein titin (TTNtv) are the most common genetic cause for dilated cardiomyopathy (DCM), a major cause of heart failure and premature death. Here we show that cardiac microtissues engineered from human induced pluripotent stem (iPS) cells are a powerful system for evaluating the pathogenicity of titin gene variants. We found that certain missense mutations, like TTNtv, diminish contractile performance and are pathogenic. By combining functional analyses with RNAseq, we explain why truncations in the A-band domain of TTN cause DCM while truncations in the I-band are better tolerated. Finally, we demonstrate that mutant titin protein in iPS-cardiomyocytes results in sarcomere insufficiency, impaired responses to mechanical and β-adrenergic stress, and attenuated growth factor and cell signaling activation. Our findings indicate that titin mutations cause DCM by disrupting critical linkages between sarcomerogenesis and adaptive remodelling. PMID:26315439

47 CFR 73.51 - Determining operating power.

Code of Federal Regulations, 2011 CFR

2011-10-01

... stage of the transmitter, using the following formula: Where: Antenna input power = Ep × Ip × F Ep=DC input voltage of final radio stage. Ip=Total DC input current of final radio stage. F= Efficiency factor...

75 FR 16655 - Airworthiness Directives; Rolls-Royce plc RB211-Trent 700 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-02

... pressure (HP-IP) turbine internal and external oil vent tubes for coking and carbon buildup, and cleaning... borescope inspections of the HP-IP turbine internal and external oil vent tubes for coking and carbon...-intermediate pressure (HP-IP) turbine internal oil vent tubes, external oil vent tubes, and bearing chamber...

Technology Implementation Plan: Irradiation Testing and Qualification for Nuclear Thermal Propulsion Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harrison, Thomas J.; Howard, Richard H.; Rader, Jordan D.

This document is a notional technology implementation plan (TIP) for the development, testing, and qualification of a prototypic fuel element to support design and construction of a nuclear thermal propulsion (NTP) engine, specifically its pre-flight ground test. This TIP outlines a generic methodology for the progression from non-nuclear out-of-pile (OOP) testing through nuclear in-pile (IP) testing, at operational temperatures, flows, and specific powers, of an NTP fuel element in an existing test reactor. Subsequent post-irradiation examination (PIE) will occur in existing radiological facilities. Further, the methodology is intended to be nonspecific with respect to fuel types and irradiation or examinationmore » facilities. The goals of OOP and IP testing are to provide confidence in the operational performance of fuel system concepts and provide data to program leadership for system optimization and fuel down-selection. The test methodology, parameters, collected data, and analytical results from OOP, IP, and PIE will be documented for reference by the NTP operator and the appropriate regulatory and oversight authorities. Final full-scale integrated testing would be performed separately by the reactor operator as part of the preflight ground test.« less

IP-1 Certification of Cargo Containers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hagler, Lisle

The purpose and scope of this engineering note is to demonstrate that the structural design of the cargo container complies with the IP-1 container requirements of 49 CFR 173.410 as required by CFR 173.411.

Naval Postgraduate School Research. Volume 11, Number 2, June 2001

DTIC Science & Technology

2001-06-01

Asynchronous Transfer Mode Protocols for Communi- cation of TCP / IP Based Voice, Video and Data over Long Delay Wireless Links.” LCDR Bermingham is...accurate, DD-21 is planned to employ an Integrated Power System ( IPS ), where both ship service and ship propulsion power are derived from a common set...electric drive and to shipboard distribu- tion. The advantages of electric drive and IPS are manifold including: a reduction in the number of prime movers

Advances in simulation of wave interactions with extended MHD phenomena

NASA Astrophysics Data System (ADS)

Batchelor, D.; Abla, G.; D'Azevedo, E.; Bateman, G.; Bernholdt, D. E.; Berry, L.; Bonoli, P.; Bramley, R.; Breslau, J.; Chance, M.; Chen, J.; Choi, M.; Elwasif, W.; Foley, S.; Fu, G.; Harvey, R.; Jaeger, E.; Jardin, S.; Jenkins, T.; Keyes, D.; Klasky, S.; Kruger, S.; Ku, L.; Lynch, V.; McCune, D.; Ramos, J.; Schissel, D.; Schnack, D.; Wright, J.

2009-07-01

The Integrated Plasma Simulator (IPS) provides a framework within which some of the most advanced, massively-parallel fusion modeling codes can be interoperated to provide a detailed picture of the multi-physics processes involved in fusion experiments. The presentation will cover four topics: 1) recent improvements to the IPS, 2) application of the IPS for very high resolution simulations of ITER scenarios, 3) studies of resistive and ideal MHD stability in tokamk discharges using IPS facilities, and 4) the application of RF power in the electron cyclotron range of frequencies to control slowly growing MHD modes in tokamaks and initial evaluations of optimized location for RF power deposition.

Intermittent 20-HZ-photic stimulation leads to a uniform reduction of alpha-global field power in healthy volunteers.

PubMed

Rau, R; Raschka, C; Koch, H J

2001-01-01

19-channel-EEGs were recorded from scalp surface of 30 healthy subjects (16m, 14f, mean age: 34 ys, SD: 11.7 ys) at rest and under IPS (Intermittent Photic Stimulation) at rates of 5, 10 and 20 Hertz (Hz). Digitalized data underwent spectral analysis with fast fourier transfomation (FFT) yielding the basis for the computation of global field power (GFP). For quantification GFP values in the frequency ranges of 5, 10 and 20 Hz at rest were divided by the corresponding data gained under IPS. While ratios from PDE data showed no stable parameter due to high interindividual variability, ratios of alpha-power turned out to be uniform in all subjects: IPS at 20 Hz always led to a suppression of alpha-power. Dividing alpha-GFP at rest by alpha-GFP under 20-Hz IPS thus resulted in a ratio < 1. We conclude that ratios from GFP data are a stable diagnostic paradigma.

Applying the systems engineering approach to video over IP projects : workshop.

DOT National Transportation Integrated Search

2011-12-01

In 2009, the Texas Transportation Institute produced for the Texas Department of Transportation a document : called Video over IP Design Guidebook. This report summarizes an implementation of that project in the : form of a workshop. The workshop was...

The Characteristic Response of Whistler Mode Waves to Interplanetary Shocks

DOE PAGES

Yue, Chao; Chen, Lunjin; Bortnik, Jacob; ...

2017-09-29

Magnetospheric whistler mode waves play a key role in regulating the dynamics of the electron radiation belts. Recent satellite observations indicate a significant influence of interplanetary (IP) shocks on whistler mode wave power in the inner magnetosphere. In this study, we statistically investigate the response of whistler mode chorus and plasmaspheric hiss to IP shocks based on Van Allen Probes and THEMIS satellite observations. Immediately after the IP shock arrival, chorus wave power is usually intensified, often at postmidnight to prenoon sector, while plasmaspheric hiss wave power predominantly decreases near the dayside but intensifies near the nightside. We conclude thatmore » chorus wave intensification outside the plasmasphere is probably associated with the suprathermal electron flux enhancement caused by the IP shock. Through a simple ray tracing modeling assuming the scenario that plasmaspheric hiss is originated from chorus, we find that the solar wind dynamic pressure increase changes the magnetic field configuration to favor ray penetration in the nightside and promote ray refraction away from the dayside, potentially explaining the magnetic local time–dependent responses of plasmaspheric hiss waves following IP shock arrivals.« less

The Characteristic Response of Whistler Mode Waves to Interplanetary Shocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yue, Chao; Chen, Lunjin; Bortnik, Jacob

Magnetospheric whistler mode waves play a key role in regulating the dynamics of the electron radiation belts. Recent satellite observations indicate a significant influence of interplanetary (IP) shocks on whistler mode wave power in the inner magnetosphere. In this study, we statistically investigate the response of whistler mode chorus and plasmaspheric hiss to IP shocks based on Van Allen Probes and THEMIS satellite observations. Immediately after the IP shock arrival, chorus wave power is usually intensified, often at postmidnight to prenoon sector, while plasmaspheric hiss wave power predominantly decreases near the dayside but intensifies near the nightside. We conclude thatmore » chorus wave intensification outside the plasmasphere is probably associated with the suprathermal electron flux enhancement caused by the IP shock. Through a simple ray tracing modeling assuming the scenario that plasmaspheric hiss is originated from chorus, we find that the solar wind dynamic pressure increase changes the magnetic field configuration to favor ray penetration in the nightside and promote ray refraction away from the dayside, potentially explaining the magnetic local time–dependent responses of plasmaspheric hiss waves following IP shock arrivals.« less

Energy star compliant voice over internet protocol (VoIP) telecommunications network including energy star compliant VoIP devices

DOEpatents

Kouchri, Farrokh Mohammadzadeh

2012-11-06

A Voice over Internet Protocol (VoIP) communications system, a method of managing a communications network in such a system and a program product therefore. The system/network includes an ENERGY STAR (E-star) aware softswitch and E-star compliant communications devices at system endpoints. The E-star aware softswitch allows E-star compliant communications devices to enter and remain in power saving mode. The E-star aware softswitch spools messages and forwards only selected messages (e.g., calls) to the devices in power saving mode. When the E-star compliant communications devices exit power saving mode, the E-star aware softswitch forwards spooled messages.

Mission Applicability Assessment of Integrated Power Components and Systems

NASA Technical Reports Server (NTRS)

Raffaelle, R. P.; Hepp, A. F.; Landis, G. A.; Hoffman, D. J.

2002-01-01

The need for smaller lightweight autonomous power systems has recently increased with the increasing focus on micro- and nanosatellites. Small area high-efficiency thin film batteries and solar cells are an attractive choice for such applications. The NASA Glenn Research Center, Johns Hopkins Applied Physics Laboratory, Lithium Power Technologies, MicroSat Systems, and others, have been working on the development of autonomous monolithic packages combining these elements or what are called integrated power supplies (IPS). These supplies can be combined with individual satellite components and are capable of providing continuous power even under intermittent illumination associated with a spinning or Earth orbiting satellite. This paper discusses the space mission applicability, benefits, and current development efforts associated with integrated power supply components and systems. The characteristics and several mission concepts for an IPS that combines thin-film photovoltaic power generation with thin-film lithium ion energy storage are described. Based on this preliminary assessment, it is concluded that the most likely and beneficial application of an IPS will be for small "nanosatellites" or in specialized applications serving as a decentralized or as a distributed power source or uninterruptible power supply.

Rearing-environment-dependent hippocampal local field potential differences in wild-type and inositol trisphosphate receptor type 2 knockout mice.

PubMed

Tanaka, Mika; Wang, Xiaowen; Mikoshiba, Katsuhiko; Hirase, Hajime; Shinohara, Yoshiaki

2017-10-15

Mice reared in an enriched environment are demonstrated to have larger hippocampal gamma oscillations than those reared in isolation, thereby confirming previous observations in rats. To test whether astrocytic Ca 2+ surges are involved in this experience-dependent LFP pattern modulation, we used inositol trisphosphate receptor type 2 (IP 3 R2)-knockout (KO) mice, in which IP 3 /Ca 2+ signalling in astrocytes is largely diminished. We found that this experience-dependent gamma power alteration persists in the KO mice. Interestingly, hippocampal ripple events, the synchronized events critical for memory consolidation, are reduced in magnitude and frequency by both isolated rearing and IP 3 R2 deficiency. Rearing in an enriched environment (ENR) is known to enhance cognitive and memory abilities in rodents, whereas social isolation (ISO) induces depression-like behaviour. The hippocampus has been documented to undergo morphological and functional changes depending on these rearing environments. For example, rearing condition during juvenility alters CA1 stratum radiatum gamma oscillation power in rats. In the present study, hippocampal CA1 local field potentials (LFP) were recorded from bilateral CA1 in urethane-anaesthetized mice that were reared in either an ENR or ISO condition. Similar to previous findings in rats, gamma oscillation power during theta states was higher in the ENR group. Ripple events that occur during non-theta periods in the CA1 stratum pyramidale also had longer intervals in ISO mice. Because astrocytic Ca 2+ elevations play a key role in synaptic plasticity, we next tested whether these changes in LFP are also expressed in inositol trisphosphate receptor type 2 (IP 3 R2)-knockout (KO) mice, in which astrocytic Ca 2+ elevations are largely diminished. We found that the gamma power was also higher in IP 3 R2-KO-ENR mice compared to IP 3 R2-KO-ISO mice, suggesting that the rearing-environment-dependent gamma power alteration does not necessarily require the astrocytic IP 3 /Ca 2+ pathway. By contrast, ripple events showed genotype-dependent changes, as well as rearing condition-dependent changes: ISO housing and IP 3 R2 deficiency both lead to longer inter-ripple intervals. Moreover, we found that ripple magnitude in the right CA1 tended to be smaller in IP 3 R2-KO. Because IP 3 R2-KO mice have been reported to have depression phenotypes, our results suggest that ripple events and the mood of animals may be broadly correlated. © 2017 The Authors. The Journal of Physiology © 2017 The Physiological Society.

An Integrated Specification and Verification Environment for Component-Based Architectures of Large-Scale Distributed Systems

DTIC Science & Technology

2009-05-26

Interrupt HW Interrupt DFS Dynamic Frequency Selection TPC Transmit Power Control r- MPX Hub ! i j I Power Supply Init/Reset A/D...values of several variables: from IN_0_DAT when the Mailbox forwards data supplied by Client 0, from OUT1DAT when the conditions on the ready flags are...logically implies ip y 0, and also <j> logically implies ip y <p; (b) if for all i we have that cj>t+1 is of the form (p% y ip, then the chain

Elimination of remaining undifferentiated induced pluripotent stem cells in the process of human cardiac cell sheet fabrication using a methionine-free culture condition.

PubMed

Matsuura, Katsuhisa; Kodama, Fumiko; Sugiyama, Kasumi; Shimizu, Tatsuya; Hagiwara, Nobuhisa; Okano, Teruo

2015-03-01

Cardiac tissue engineering is a promising method for regenerative medicine. Although we have developed human cardiac cell sheets by integration of cell sheet-based tissue engineering and scalable bioreactor culture, the risk of contamination by induced pluripotent stem (iPS) cells in cardiac cell sheets remains unresolved. In the present study, we established a novel culture method to fabricate human cardiac cell sheets with a decreased risk of iPS cell contamination while maintaining viabilities of iPS cell-derived cells, including cardiomyocytes and fibroblasts, using a methionine-free culture condition. When cultured in the methionine-free condition, human iPS cells did not survive without feeder cells and could not proliferate or form colonies on feeder cells or in coculture with cells for cardiac cell sheet fabrication. When iPS cell-derived cells after the cardiac differentiation were transiently cultured in the methionine-free condition, gene expression of OCT3/4 and NANOG was downregulated significantly compared with that in the standard culture condition. Furthermore, in fabricated cardiac cell sheets, spontaneous and synchronous beating was observed in the whole area while maintaining or upregulating the expression of various cardiac and extracellular matrix genes. These findings suggest that human iPS cells are methionine dependent and a methionine-free culture condition for cardiac cell sheet fabrication might reduce the risk of iPS cell contamination.

Teaching Network Security with IP Darkspace Data

ERIC Educational Resources Information Center

Zseby, Tanja; Iglesias Vázquez, Félix; King, Alistair; Claffy, K. C.

2016-01-01

This paper presents a network security laboratory project for teaching network traffic anomaly detection methods to electrical engineering students. The project design follows a research-oriented teaching principle, enabling students to make their own discoveries in real network traffic, using data captured from a large IP darkspace monitor…

Two different electrical properties can improve transoceanic cable-route mapping

USGS Publications Warehouse

Wynn, J.; McGinnis, T.

2001-01-01

Induced polarization (IP) measurements made in the marine environment were investigated to map and remotely characterize the top 6-10 meters of the seafloor. The continuous resistivity profiling with cone-penetrometer tests, providing important information to engineers planning transoceanic cable routes, was also described. The IP effect and resistivity were identified as the two electric properties to improve transoceanic cable-route mapping. The measurement of IP and resistivity was found to depend on electrical current.

Bioenvironmental Engineer’s Guide to TVA-1000B Toxic Vapor Analyzer

DTIC Science & Technology

2014-01-01

chemicals including aromatics, unsaturated chlorinated hydrocarbons, aldehydes , ketones , ethylene oxide, hydrogen sulfide, and glycol ether solvents. The...Dimethoxyethane 9.65 Diethyl ketone 9.32 Ethyl amine 8.86 1,1-Dimethylhydrazine 7.28 Diethyl sulfide 8.43 Ethyl benzene 8.76 1,2-Dibromoethene 9.45...Chemical IP (eV) Chemical IP (eV) Chemical IP (eV) Freon 13 (chlorotrifluoromethane) 12.91 Isobutyric acid 10.02 Methyl butyl ketone 9.34

Plasma current ramp-up by lower hybrid wave using innovative antennas on TST-2

NASA Astrophysics Data System (ADS)

Takase, Yuichi; Ejiri, Akira; Moeller, Charles; Roidl, Benedikt; Shinya, Takahiro; Tsujii, Naoto; Yajima, Satoru; Yamazaki, Hibiki; Kitayama, Akichika; Matsumoto, Naoki; Sato, Akito; Sonehara, Masateru; Takahashi, Wataru; Tajiri, Yoshiyuki; Takei, Yuki; Togashi, Hiro; Toida, Kazuya; Yoshida, Yusuke

2016-10-01

Non-inductive plasma current (Ip) ramp-up by RF power in the lower hybrid frequency range is being studied on the TST-2 spherical tokamak (R = 0.36 m, a = 0.23 m, Bt = 0.3 T, Ip = 0.1 MA). Up to 400 kW of RF power is available at a frequency of 200 MHz. An innovative antenna called the capacitively-coupled combline (CCC) antenna was developed to excite a sharp, highly directional traveling wave with the electric field polarized in the toroidal direction. It is an array of resonant circuit elements made of capacitance and inductance, coupled to neighboring elements by mutual capacitance. Two CCC antennas are installed in TST-2, a 13-element outboard-launch antenna and a 6-element top-launch antenna. The latter was installed in March 2016 to improve accessibility to the core and to achieve single-pass damping. The suspected wave power loss in the scrape-off layer plasma should also be avoided. Ip ramp-up to 25 kA has been achieved so far. An upgrade of the Bt power supply is planned to take advantage of the observed improvement of Ip ramp-up with Bt. Higher Bt for longer pulses should improve the Ip ramp-up efficiency by improving wave accessibility and by reducing prompt orbit losses of energetic electrons.

78 FR 70487 - Airworthiness Directives; Rolls-Royce plc Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-26

... Airworthiness Directives; Rolls-Royce plc Turbofan Engines AGENCY: Federal Aviation Administration (FAA), DOT... turbofan engines. This AD requires removal of certain high-pressure (HP) and intermediate-pressure (IP..., RB211 Trent 768-60, 772-60, and 772B-60 turbofan engines with turbine disc part numbers (P/Ns) and...

77 FR 56760 - Airworthiness Directives; Rolls-Royce plc Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-14

... Airworthiness Directives; Rolls-Royce plc Turbofan Engines AGENCY: Federal Aviation Administration (FAA), DOT... all Rolls-Royce plc (RR) RB211-Trent 800 series turbofan engines. This AD requires removing from...-17, 892-17, 892B-17, and 895-17 turbofan engines that have an intermediate pressure (IP) turbine disc...

ChIP-re-ChIP: Co-occupancy Analysis by Sequential Chromatin Immunoprecipitation.

PubMed

Beischlag, Timothy V; Prefontaine, Gratien G; Hankinson, Oliver

2018-01-01

Chromatin immunoprecipitation (ChIP) exploits the specific interactions between DNA and DNA-associated proteins. It can be used to examine a wide range of experimental parameters. A number of proteins bound at the same genomic location can identify a multi-protein chromatin complex where several proteins work together to regulate gene transcription or chromatin configuration. In many instances, this can be achieved using sequential ChIP; or simply, ChIP-re-ChIP. Whether it is for the examination of specific transcriptional or epigenetic regulators, or for the identification of cistromes, the ability to perform a sequential ChIP adds a higher level of power and definition to these analyses. In this chapter, we describe a simple and reliable method for the sequential ChIP assay.

77 FR 39157 - Airworthiness Directives; Rolls-Royce plc Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-02

... Airworthiness Directives; Rolls-Royce plc Turbofan Engines AGENCY: Federal Aviation Administration (FAA), DOT...-84, and 980-84 turbofan engines. That AD currently requires inspecting the intermediate-pressure (IP... RR model RB211-Trent 970-84, 970B-84, 972-84, 972B-84, 977-84, 977B-84, and 980-84 turbofan engines...

A Network Steganography Lab on Detecting TCP/IP Covert Channels

ERIC Educational Resources Information Center

Zseby, Tanja; Vázquez, Félix Iglesias; Bernhardt, Valentin; Frkat, Davor; Annessi, Robert

2016-01-01

This paper presents a network security laboratory to teach data analysis for detecting TCP/IP covert channels. The laboratory is mainly designed for students of electrical engineering, but is open to students of other technical disciplines with similar background. Covert channels provide a method for leaking data from protected systems, which is a…

ChIP-PaM: an algorithm to identify protein-DNA interaction using ChIP-Seq data.

PubMed

Wu, Song; Wang, Jianmin; Zhao, Wei; Pounds, Stanley; Cheng, Cheng

2010-06-03

ChIP-Seq is a powerful tool for identifying the interaction between genomic regulators and their bound DNAs, especially for locating transcription factor binding sites. However, high cost and high rate of false discovery of transcription factor binding sites identified from ChIP-Seq data significantly limit its application. Here we report a new algorithm, ChIP-PaM, for identifying transcription factor target regions in ChIP-Seq datasets. This algorithm makes full use of a protein-DNA binding pattern by capitalizing on three lines of evidence: 1) the tag count modelling at the peak position, 2) pattern matching of a specific tag count distribution, and 3) motif searching along the genome. A novel data-based two-step eFDR procedure is proposed to integrate the three lines of evidence to determine significantly enriched regions. Our algorithm requires no technical controls and efficiently discriminates falsely enriched regions from regions enriched by true transcription factor (TF) binding on the basis of ChIP-Seq data only. An analysis of real genomic data is presented to demonstrate our method. In a comparison with other existing methods, we found that our algorithm provides more accurate binding site discovery while maintaining comparable statistical power.

Dynamic traffic grooming with Spectrum Engineering (TG-SE) in flexible grid optical networks

NASA Astrophysics Data System (ADS)

Yu, Xiaosong; Zhao, Yongli; Zhang, Jiawei; Wang, Jianping; Zhang, Guoying; Chen, Xue; Zhang, Jie

2015-12-01

Flexible grid has emerged as an evolutionary technology to satisfy the ever increasing demand for higher spectrum efficiency and operational flexibility. To optimize the spectrum resource utilization, this paper introduces the concept of Spectrum Engineering in flex-grid optical networks. The sliceable optical transponder has been proposed to offload IP traffic to the optical layer and reduce the number of IP router ports and transponders. We discuss the impact of sliceable transponder in traffic grooming and propose several traffic-grooming schemes with Spectrum Engineering (TG-SE). Our results show that there is a tradeoff among different traffic grooming policies, which should be adopted based on the network operator's objectives. The proposed traffic grooming with Spectrum Engineering schemes can reduce OPEX as well as increase spectrum efficiency by efficiently utilizing the bandwidth variability and capability of sliceable optical transponders.

Traffic-engineering-aware shortest-path routing and its application in IP-over-WDM networks [Invited

NASA Astrophysics Data System (ADS)

Lee, Youngseok; Mukherjee, Biswanath

2004-03-01

Single shortest-path routing is known to perform poorly for Internet traffic engineering (TE) where the typical optimization objective is to minimize the maximum link load. Splitting traffic uniformly over equal-cost multiple shortest paths in open shortest path first and intermediate system-intermediate system protocols does not always minimize the maximum link load when multiple paths are not carefully selected for the global traffic demand matrix. However, a TE-aware shortest path among all the equal-cost multiple shortest paths between each ingress-egress pair can be selected such that the maximum link load is significantly reduced. IP routers can use the globally optimal TE-aware shortest path without any change to existing routing protocols and without any serious configuration overhead. While calculating TE-aware shortest paths, the destination-based forwarding constraint at a node should be satisfied, because an IP router will forward a packet to the next hop toward the destination by looking up the destination prefix. We present a mathematical problem formulation for finding a set of TE-aware shortest paths for the given network as an integer linear program, and we propose a simple heuristic for solving large instances of the problem. Then we explore the usage of our proposed algorithm for the integrated TE method in IP-over-WDM networks. The proposed algorithm is evaluated through simulations in IP networks as well as in IP-over-WDM networks.

Effects of phencyclidine (PCP) and MK 801 on the EEGq in the prefrontal cortex of conscious rats; antagonism by clozapine, and antagonists of AMPA-, alpha(1)- and 5-HT(2A)-receptors.

PubMed

Sebban, Claude; Tesolin-Decros, Brigitte; Ciprian-Ollivier, Jorge; Perret, Laurent; Spedding, Michael

2002-01-01

1. The electroencephalographic (EEG) effects of the propsychotic agent phencyclidine (PCP), were studied in conscious rats using power spectra (0 - 30 Hz), from the prefrontal cortex or sensorimotor cortex. PCP (0.1 - 3 mg kg(-1) s.c.) caused a marked dose-dependent increase in EEG power in the frontal cortex at 1 - 3 Hz with decreases in power at higher frequencies (9 - 30 Hz). At high doses (3 mg kg(-1) s.c.) the entire spectrum shifted to more positive values, indicating an increase in cortical synchronization. MK 801 (0.05 - 0.1 mg kg(-1) i.p.) caused similar effects but with lesser changes in power. 2. In contrast, the non-competitive AMPA antagonists GYKI 52466 and GYKI 53655 increased EEG power over the whole power spectrum (1 - 10 mg kg(-1) i.p.). The atypical antipsychotic clozapine (0.2 mg kg(-1) s.c.) synchronized the EEG (peak 8 Hz). The 5-HT(2A)-antagonist, M100907, specifically increased EEG power at 2 - 3 Hz at low doses (10 and 50 microg kg(-1) s.c.), whereas at higher doses (0.1 mg kg(-1) s.c.) the profile resembled that of clozapine. 3. Clozapine (0.2 mg kg(-1) s.c. ), GYKI 53655 (5 mg kg(-1) i.p.), prazosin (0.05 and 0.1 mg kg(-1) i.p.), and M100907 (0.01 and 0.05 mg kg(-1) s.c.) antagonized the decrease in power between 5 and 30 Hz caused by PCP (1 mg kg(-1) s.c.), but not the increase in power at 1 - 3 Hz in prefrontal cortex.

Security Research on VoIP with Watermarking

NASA Astrophysics Data System (ADS)

Hu, Dong; Lee, Ping

2008-11-01

With the wide application of VoIP, many problems have occurred. One of the problems is security. The problems with securing VoIP systems, insufficient standardization and lack of security mechanisms emerged the need for new approaches and solutions. In this paper, we propose a new security architecture for VoIP which is based on digital watermarking which is a new, flexible and powerful technology that is increasingly gaining more and more attentions. Besides known applications e.g. to solve copyright protection problems, we propose to use digital watermarking to secure not only transmitted audio but also signaling protocol that VoIP is based on.

Mobile telephones: a comparison of radiated power between 3G VoIP calls and 3G VoCS calls.

PubMed

Jovanovic, Dragan; Bragard, Guillaume; Picard, Dominique; Chauvin, Sébastien

2015-01-01

The purpose of this study is to assess the mean RF power radiated by mobile telephones during voice calls in 3G VoIP (Voice over Internet Protocol) using an application well known to mobile Internet users, and to compare it with the mean power radiated during voice calls in 3G VoCS (Voice over Circuit Switch) on a traditional network. Knowing that the specific absorption rate (SAR) is proportional to the mean radiated power, the user's exposure could be clearly identified at the same time. Three 3G (High Speed Packet Access) smartphones from three different manufacturers, all dual-band for GSM (900 MHz, 1800 MHz) and dual-band for UMTS (900 MHz, 1950 MHz), were used between 28 July and 04 August 2011 in Paris (France) to make 220 two-minute calls on a mobile telephone network with national coverage. The places where the calls were made were selected in such a way as to describe the whole range of usage situations of the mobile telephone. The measuring equipment, called "SYRPOM", recorded the radiation power levels and the frequency bands used during the calls with a sampling rate of 20,000 per second. In the framework of this study, the mean normalised power radiated by a telephone in 3G VoIP calls was evaluated at 0.75% maximum power of the smartphone, compared with 0.22% in 3G VoCS calls. The very low average power levels associated with use of 3G devices with VoIP or VoCS support the view that RF exposure resulting from their use is far from exceeding the basic restrictions of current exposure limits in terms of SAR.

78 FR 5 - Airworthiness Directives; Rolls-Royce plc Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-02

... Airworthiness Directives; Rolls-Royce plc Turbofan Engines AGENCY: Federal Aviation Administration (FAA), DOT...-535E4-C-37 turbofan engines. This AD was prompted by an investigation by RR concluding that certain...- 535E4-B-37; RB211-535E4-B-75; and RB211-535E4-C-37 turbofan engines with intermediate-pressure (IP...

Turbocharging of Small Internal Combustion Engines as a Means of Improving Engine/Application System Fuel Economy.

DTIC Science & Technology

1979-01-01

OF SMALL INTERNAL COMBUSTION ENGINES AS A MEANS 0-.ETC(U) 1979 DAAK7O-78-C-O031 .hhuuufBuhhhh...Aerodyne Dallas th W__tIP FINAL REPORT CONTRACT* DAAK7-78-C-0031 FTURBOCHARGING OF SMALL INTERNAL COMBUSTION ENGINE AS A MEANS OF IMPROVING ENGINE ...DAAK70-78-C0031 TURBOCHARGING OF SMALL INTERNAL COMBUSTION ENGINES AS A MEANS OF IMPROVING ENGINE /APPLICATION SYSTEM FUEL ECONOMY Prepared by

76 FR 36981 - Airworthiness Directives; Rolls-Royce plc RB211-Trent 500 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-24

... Airworthiness Directives; Rolls-Royce plc RB211--Trent 500 Series Turbofan Engines AGENCY: Federal Aviation... condition on an aviation product. The MCAI describes the unsafe condition as: A Trent 500 engine has been found with thermal distress of the Intermediate Pressure (IP) Turbine Nozzle Guide Vanes. The resultant...

Femto-second synchronisation with a waveguide interferometer

NASA Astrophysics Data System (ADS)

Dexter, A. C.; Smith, S. J.; Woolley, B. J.; Grudiev, A.

2018-03-01

CERN's compact linear collider CLIC requires crab cavities on opposing linacs to rotate bunches of particles into alignment at the interaction point (IP). These cavities are located approximately 25 metres either side of the IP. The luminosity target requires synchronisation of their RF phases to better than 5 fs r.m.s. This is to be achieved by powering both cavities from one high power RF source, splitting the power and delivering it along two waveguide paths that are controlled to be identical in length to within a micrometre. The waveguide will be operated as an interferometer. A high power phase shifter for adjusting path lengths has been successfully developed and operated in an interferometer. The synchronisation target has been achieved in a low power prototype system.

Biological activities of the polysaccharides produced in submerged culture of two edible Pleurotus ostreatus mushrooms.

PubMed

Vamanu, Emanuel

2012-01-01

Exopolysaccharides (EPS) and internal (intracellular) polysaccharides (IPS) obtained from the Pleurotus ostreatus M2191 and PBS281009 cultivated using the batch system revealed an average of between 0.1-2 (EPS) and 0.07-1.5 g/L/day (IPS). The carbohydrate analysis revealed that the polysaccharides comprised 87-89% EPS and 68-74% IPS. The investigation of antioxidant activity in vitro revealed a good antioxidant potential, particularly for the IPS and EPS isolated from PBS281009, as proved by the EC(50) value for DPPH, ABTS scavenging activity, reducing power, and iron chelating activity.

Modelling IRF8 Deficient Human Hematopoiesis and Dendritic Cell Development with Engineered iPS Cells.

PubMed

Sontag, Stephanie; Förster, Malrun; Qin, Jie; Wanek, Paul; Mitzka, Saskia; Schüler, Herdit M; Koschmieder, Steffen; Rose-John, Stefan; Seré, Kristin; Zenke, Martin

2017-04-01

Human induced pluripotent stem (iPS) cells can differentiate into cells of all three germ layers, including hematopoietic stem cells and their progeny. Interferon regulatory factor 8 (IRF8) is a transcription factor, which acts in hematopoiesis as lineage determining factor for myeloid cells, including dendritic cells (DC). Autosomal recessive or dominant IRF8 mutations occurring in patients cause severe monocytic and DC immunodeficiency. To study IRF8 in human hematopoiesis we generated human IRF8-/- iPS cells and IRF8-/- embryonic stem (ES) cells using RNA guided CRISPR/Cas9n genome editing. Upon induction of hematopoietic differentiation, we demonstrate that IRF8 is dispensable for iPS cell and ES cell differentiation into hemogenic endothelium and for endothelial-to-hematopoietic transition, and thus development of hematopoietic progenitors. We differentiated iPS cell and ES cell derived progenitors into CD141+ cross-presenting cDC1 and CD1c+ classical cDC2 and CD303+ plasmacytoid DC (pDC). We found that IRF8 deficiency compromised cDC1 and pDC development, while cDC2 development was largely unaffected. Additionally, in an unrestricted differentiation regimen, IRF8-/- iPS cells and ES cells exhibited a clear bias toward granulocytes at the expense of monocytes. IRF8-/- DC showed reduced MHC class II expression and were impaired in cytokine responses, migration, and antigen presentation. Taken together, we engineered a human IRF8 knockout model that allows studying molecular mechanisms of human immunodeficiencies in vitro, including the pathophysiology of IRF8 deficient DC. Stem Cells 2017;35:898-908. © 2017 The Authors Stem Cells published by Wiley Periodicals, Inc. on behalf of AlphaMed Press.

Tier-1 assays for assessing the toxicity of insecticidal proteins produced by genetically engineered plants to non-target arthropods.

PubMed

Li, Yun-He; Romeis, Jörg; Wu, Kong-Ming; Peng, Yu-Fa

2014-04-01

In assessing an insect-resistant genetically engineered (IRGE) crop before its commercialization, researchers normally use so-called "Tier-1 assays" as the initial step to determine the effects of the crop on non-target organisms. In these tests, the insecticidal proteins (IPs) produced by the IRGEs are added to the diets of test organisms in the laboratory. Test organisms in such assays can be directly exposed to much higher concentrations of the test IPs than they would encounter in the field. The results of Tier-1 assays are thus more conservative than those generated in studies in which the organisms are exposed to the IPs by feeding on IRGE plant tissue or in the case of predators or parasites, by feeding on invertebrate prey or hosts that have fed on IRGE plant tissue. In this report, we consider three important factors that must be considered in Tier-1 assays: (i) methods for delivery of the IP to the test organisms; (ii) the need for and selection of compounds used as positive controls; and (iii) methods for monitoring the concentration, stability and bioactivity of the IP during the assay. We also analyze the existing data from Tier-1 assays regarding the toxicity of Bt Cry proteins to non-target arthropod species. The data indicate that the widely used Bt proteins have no direct toxicity to non-target organisms. © 2013 Institute of Zoology, Chinese Academy of Sciences.

Role of intellectual property in investment-backed personalized medicine.

PubMed

Norviel, Vern; Akhavan, Ray; Alemozafar, Ali R

2010-01-01

Personalized medicine is a growing field that promises to provide individualized treatment that is tailored to each patient. For a startup personalized medicine company, an initial step in securing financing is to protect its intellectual property (IP), for example, through patent protection. When deciding whether to invest in a personalized medicine company, investors, such as venture capitalists, assess the scope of a personalized medicine company's protection of its IP. Patent protection is a powerful way for a personalized medicine startup company to protect its IP, but patent protection for personalized medicine inventions can differ from one country to another. A personalized medicine company could benefit from developing a well-defined IP strategy for maximizing the scope and breadth of its IP protection.

Use of Cumulative Degradation Factor Prediction and Life Test Result of the Thruster Gimbal Assembly Actuator for the Dawn Flight Project

NASA Technical Reports Server (NTRS)

Lo, C. John; Brophy, John R.; Etters, M. Andy; Ramesham, Rajeshuni; Jones, William R., Jr.; Jansen, Mark J.

2009-01-01

The Dawn Ion Propulsion System is the ninth project in NASA s Discovery Program. The Dawn spacecraft is being developed to enable the scientific investigation of the two heaviest main-belt asteroids, Vesta and Ceres. Dawn is the first mission to orbit two extraterrestrial bodies, and the first to orbit a main-belt asteroid. The mission is enabled by the onboard Ion Propulsion System (IPS) to provide the post-launch delta-V. The three Ion Engines of the IPS are mounted on Thruster Gimbal Assembly (TGA), with only one engine operating at a time for this 10-year mission. The three TGAs weigh 14.6 kg.

SlimCS—compact low aspect ratio DEMO reactor with reduced-size central solenoid

NASA Astrophysics Data System (ADS)

Tobita, K.; Nishio, S.; Sato, M.; Sakurai, S.; Hayashi, T.; Shibama, Y. K.; Isono, T.; Enoeda, M.; Nakamura, H.; Sato, S.; Ezato, K.; Hayashi, T.; Hirose, T.; Ide, S.; Inoue, T.; Kamada, Y.; Kawamura, Y.; Kawashima, H.; Koizumi, N.; Kurita, G.; Nakamura, Y.; Mouri, K.; Nishitani, T.; Ohmori, J.; Oyama, N.; Sakamoto, K.; Suzuki, S.; Suzuki, T.; Tanigawa, H.; Tsuchiya, K.; Tsuru, D.

2007-08-01

The concept for a compact DEMO reactor named 'SlimCS' is presented. Distinctive features of the concept are low aspect ratio (A = 2.6) and use of a reduced-size centre solenoid (CS) which has the function of plasma shaping rather than poloidal flux supply. The reduced-size CS enables us to introduce a thin toroidal field coil system which contributes to reducing the weight and perhaps lessening the construction cost. Low-A has merits of vertical stability for high elongation (κ) and high normalized beta (βN), which leads to a high power density with reasonable physics requirements. This is because high κ facilitates high nGW (because of an increase in Ip), which allows efficient use of the capacity of high βN. From an engineering aspect, low-A may ensure ease in designing blanket modules robust to electromagnetic forces acting on disruptions. Thus, a superconducting low-A tokamak reactor such as SlimCS can be a promising DEMO concept with physics and engineering advantages.

Thermal Analysis of the MC1 Engine Turbopump

NASA Technical Reports Server (NTRS)

Roman, Jose; Turner, Larry D. (Technical Monitor)

2001-01-01

The MC1 Engine turbopump supplied the propellants to the main injector. The turbopump consisted of four parts; lox pump, interpropellant seal package (IPS), RP pump and turbine. The thermal analysis was divided into two 2D finite element models; Housing or stationary parts and rotor or rotating parts. Both models were analyzed at the same boundary conditions using SINDA. The housing model consisted of, lox pump housing, ips housing, RP housing, turbine inlet housing, turbine housing, exit guide vane, heat shield and both bearing outer races. The rotor model consisted of the lox impeller; lox end bearing and id race, RP impeller, and RP bearing and id race, shaft and turbine disk. The objectives of the analysis were to: (1) verified the original design and recommend modifications to it, (2) submitted a thermal environment to support the structural analysis, (3) support the component and engine test program. and (4) to support the X34 vehicle program.

Thermal Analysis of the MCI Engine Turbopump

NASA Technical Reports Server (NTRS)

Roman, Jose

2002-01-01

The MCI Engine turbopump supplied the propellants to the main injector. The turbopump consisted of four parts; lox pump, interpropellant seal package (IPS), RP pump and turbine. The thermal analysis was divided into two 2D finite element models; Housing or stationary parts and rotor or rotating parts. Both models were analyzed at the same boundary conditions using SINDA. The housing model consisted of; lox pump housing, ips housing, RP housing, turbine inlet housing, turbine housing, exit guide vane, heat shield and both bearing outer races. The rotor model consisted of the lox impeller; lox end bearing and id race, RP impeller, and RP bearing and id race, shaft and turbine disk. The objectives of the analysis were to (1) verified the original design and recommend modifications to it, (2) submitted a thermal environment to support the structural analysis, (3) support the component and engine test program and (4) to support the X34 vehicle program.

Transient Analysis of Pressurization and Pneumatic Subsystems of the X-34 Main Propulsion System

NASA Technical Reports Server (NTRS)

Hedayat, A.; Knight, K. C.; Chamption, R. H., Jr.; Kennedy, Jim W. (Technical Monitor)

2000-01-01

Transient models for the pressurization, vent/relief, and pneumatic subsystems of the X-34 Main Propulsion System are presented and simulation of their operation within prescribed requirements are provided. First, using ROCket Engine Transient Simulation (ROCETS) program, pressurization subsystem operation was simulated and helium requirements and the ullage thermodynamic condition within each propellant tank were calculated. Then, Overpressurization scenarios of propellant tanks and the response of vent/relief valves were evaluated using ROCETS simulation of simultaneous operation of the pressurization and vent/relief subsystems by incorporating the valves data into the model. Finally, the ROCETS simulation of in-flight operation of pneumatic subsystem predicted the overall helium consumption, Inter-Propellant Seal (IPS) purge flowrate and thermodynamic conditions, and Spin Start power.

An Impact Assessment Model for Distributed Adaptive Security Situation Assessment

DTIC Science & Technology

2005-01-01

the cargo manifest can be either a 56K modem-based TCP/IP connection (the oval labeled internet) or a 40K wireless modem connection ( cell phone ) that...via a UDP connection on the 40K wireless modem ( cell phone ). For each resource, either alternative may be used to achieve the same goal, but some...Manifests Comm-in Comp- power Comm- out JTF Internet (TCP-IP) Cell phone (TCP-IP) Internet (UDP) Cell phone (UDP) Manual Computer 4

Interferon-gamma improves impaired dentinogenic and immunosuppressive functions of irreversible pulpitis-derived human dental pulp stem cells

PubMed Central

Sonoda, Soichiro; Yamaza, Haruyoshi; Ma, Lan; Tanaka, Yosuke; Tomoda, Erika; Aijima, Reona; Nonaka, Kazuaki; Kukita, Toshio; Shi, Songtao; Nishimura, Fusanori; Yamaza, Takayoshi

2016-01-01

Clinically, irreversible pulpitis is treated by the complete removal of pulp tissue followed by replacement with artificial materials. There is considered to be a high potential for autologous transplantation of human dental pulp stem cells (DPSCs) in endodontic treatment. The usefulness of DPSCs isolated from healthy teeth is limited. However, DPSCs isolated from diseased teeth with irreversible pulpitis (IP-DPSCs) are considered to be suitable for dentin/pulp regeneration. In this study, we examined the stem cell potency of IP-DPSCs. In comparison with healthy DPSCs, IP-DPSCs expressed lower colony-forming capacity, population-doubling rate, cell proliferation, multipotency, in vivo dentin regeneration, and immunosuppressive activity, suggesting that intact IP-DPSCs may be inadequate for dentin/pulp regeneration. Therefore, we attempted to improve the impaired in vivo dentin regeneration and in vitro immunosuppressive functions of IP-DPSCs to enable dentin/pulp regeneration. Interferon gamma (IFN-γ) treatment enhanced in vivo dentin regeneration and in vitro T cell suppression of IP-DPSCs, whereas treatment with tumor necrosis factor alpha did not. Therefore, these findings suggest that IFN-γ may be a feasible modulator to improve the functions of impaired IP-DPSCs, suggesting that autologous transplantation of IFN-γ-accelerated IP-DPSCs might be a promising new therapeutic strategy for dentin/pulp tissue engineering in future endodontic treatment. PMID:26775677

Efficient sequence-specific isolation of DNA fragments and chromatin by in vitro enChIP technology using recombinant CRISPR ribonucleoproteins.

PubMed

Fujita, Toshitsugu; Yuno, Miyuki; Fujii, Hodaka

2016-04-01

The clustered regularly interspaced short palindromic repeats (CRISPR) system is widely used for various biological applications, including genome editing. We developed engineered DNA-binding molecule-mediated chromatin immunoprecipitation (enChIP) using CRISPR to isolate target genomic regions from cells for their biochemical characterization. In this study, we developed 'in vitro enChIP' using recombinant CRISPR ribonucleoproteins (RNPs) to isolate target genomic regions. in vitro enChIP has the great advantage over conventional enChIP of not requiring expression of CRISPR complexes in cells. We first showed that in vitro enChIP using recombinant CRISPR RNPs can be used to isolate target DNA from mixtures of purified DNA in a sequence-specific manner. In addition, we showed that this technology can be used to efficiently isolate target genomic regions, while retaining their intracellular molecular interactions, with negligible contamination from irrelevant genomic regions. Thus, in vitro enChIP technology is of potential use for sequence-specific isolation of DNA, as well as for identification of molecules interacting with genomic regions of interest in vivo in combination with downstream analysis. © 2016 The Authors. Genes to Cells published by Molecular Biology Society of Japan and John Wiley & Sons Australia, Ltd.

Analysis of Optimal Jitter Buffer Size for VoIP QoS under WiMAX Power-Saving Mode

NASA Astrophysics Data System (ADS)

Kim, Hyungsuk; Kim, Taehyoun

VoIP service is expected as one of the key applications of Mobile WiMAX, but the speech quality of VoIP service often suffers deterioration due to the fluctuating transmission delay called jitter. This is commonly ameliorated by a de-jitter buffer, and we aim to find the optimal size of de-jitter buffer to achieve speech quality comparable to PSTN. We developed a new model of the packet drops at the de-jitter buffer and the end-to-end packet delay which takes account of the additional delay introduced by the WiMAX power-saving mode. Using our model, we analyzed the optimal size of the de-jitter buffer for various network parameters, and showed that the results obtained by analysis accord with simulation results.

Effects of phencyclidine (PCP) and MK 801 on the EEGq in the prefrontal cortex of conscious rats; antagonism by clozapine, and antagonists of AMPA-, α1- and 5-HT2A-receptors

PubMed Central

Sebban, Claude; Tesolin-Decros, Brigitte; Ciprian-Ollivier, Jorge; Perret, Laurent; Spedding, Michael

2002-01-01

The electroencephalographic (EEG) effects of the propsychotic agent phencyclidine (PCP), were studied in conscious rats using power spectra (0 – 30 Hz), from the prefrontal cortex or sensorimotor cortex. PCP (0.1 – 3 mg kg−1 s.c.) caused a marked dose-dependent increase in EEG power in the frontal cortex at 1 – 3 Hz with decreases in power at higher frequencies (9 – 30 Hz). At high doses (3 mg kg−1 s.c.) the entire spectrum shifted to more positive values, indicating an increase in cortical synchronization. MK 801 (0.05 – 0.1 mg kg−1 i.p.) caused similar effects but with lesser changes in power. In contrast, the non-competitive AMPA antagonists GYKI 52466 and GYKI 53655 increased EEG power over the whole power spectrum (1 – 10 mg kg−1 i.p.) The atypical antipsychotic clozapine (0.2 mg kg−1 s.c.) synchronized the EEG (peak 8 Hz). The 5-HT2A-antagonist, M100907, specifically increased EEG power at 2 – 3 Hz at low doses (10 and 50 μg kg÷1 s.c.), whereas at higher doses (0.1 mg kg−1 s.c.) the profile resembled that of clozapine. Clozapine (0.2 mg kg−1 s.c.), GYKI 53655 (5 mg kg−1 i.p.), prazosin (0.05 and 0.1 mg kg−1 i.p.), and M100907 (0.01 and 0.05 mg kg−1 s.c.) antagonized the decrease in power between 5 and 30 Hz caused by PCP (1 mg kg−1 s.c.), but not the increase in power at 1 – 3 Hz in prefrontal cortex. PMID:11786481

The Ames Power Monitoring System

NASA Technical Reports Server (NTRS)

Osetinsky, Leonid; Wang, David

2003-01-01

The Ames Power Monitoring System (APMS) is a centralized system of power meters, computer hardware, and specialpurpose software that collects and stores electrical power data by various facilities at Ames Research Center (ARC). This system is needed because of the large and varying nature of the overall ARC power demand, which has been observed to range from 20 to 200 MW. Large portions of peak demand can be attributed to only three wind tunnels (60, 180, and 100 MW, respectively). The APMS helps ARC avoid or minimize costly demand charges by enabling wind-tunnel operators, test engineers, and the power manager to monitor total demand for center in real time. These persons receive the information they need to manage and schedule energy-intensive research in advance and to adjust loads in real time to ensure that the overall maximum allowable demand is not exceeded. The APMS (see figure) includes a server computer running the Windows NT operating system and can, in principle, include an unlimited number of power meters and client computers. As configured at the time of reporting the information for this article, the APMS includes more than 40 power meters monitoring all the major research facilities, plus 15 Windows-based client personal computers that display real-time and historical data to users via graphical user interfaces (GUIs). The power meters and client computers communicate with the server using Transmission Control Protocol/Internet Protocol (TCP/IP) on Ethernet networks, variously, through dedicated fiber-optic cables or through the pre-existing ARC local-area network (ARCLAN). The APMS has enabled ARC to achieve significant savings ($1.2 million in 2001) in the cost of power and electric energy by helping personnel to maintain total demand below monthly allowable levels, to manage the overall power factor to avoid low power factor penalties, and to use historical system data to identify opportunities for additional energy savings. The APMS also provides power engineers and electricians with the information they need to plan modifications in advance and perform day-to-day maintenance of the ARC electric-power distribution system.

A Mechanism for Reliable Mobility Management for Internet of Things Using CoAP

PubMed Central

Chun, Seung-Man; Park, Jong-Tae

2017-01-01

Under unreliable constrained wireless networks for Internet of Things (IoT) environments, the loss of the signaling message may frequently occur. Mobile Internet Protocol version 6 (MIPv6) and its variants do not consider this situation. Consequently, as a constrained device moves around different wireless networks, its Internet Protocol (IP) connectivity may be frequently disrupted and power can be drained rapidly. This can result in the loss of important sensing data or a large delay for time-critical IoT services such as healthcare monitoring and disaster management. This paper presents a reliable mobility management mechanism in Internet of Things environments with lossy low-power constrained device and network characteristics. The idea is to use the Internet Engineering Task Force (IETF) Constrained Application Protocol (CoAP) retransmission mechanism to achieve both reliability and simplicity for reliable IoT mobility management. Detailed architecture, algorithms, and message extensions for reliable mobility management are presented. Finally, performance is evaluated using both mathematical analysis and simulation. PMID:28085109

A Mechanism for Reliable Mobility Management for Internet of Things Using CoAP.

PubMed

Chun, Seung-Man; Park, Jong-Tae

2017-01-12

Under unreliable constrained wireless networks for Internet of Things (IoT) environments, the loss of the signaling message may frequently occur. Mobile Internet Protocol version 6 (MIPv6) and its variants do not consider this situation. Consequently, as a constrained device moves around different wireless networks, its Internet Protocol (IP) connectivity may be frequently disrupted and power can be drained rapidly. This can result in the loss of important sensing data or a large delay for time-critical IoT services such as healthcare monitoring and disaster management. This paper presents a reliable mobility management mechanism in Internet of Things environments with lossy low-power constrained device and network characteristics. The idea is to use the Internet Engineering Task Force (IETF) Constrained Application Protocol (CoAP) retransmission mechanism to achieve both reliability and simplicity for reliable IoT mobility management. Detailed architecture, algorithms, and message extensions for reliable mobility management are presented. Finally, performance is evaluated using both mathematical analysis and simulation.

[Progress and application prospect of pig induced pluripotent stem cells].

PubMed

Yan, Yi-Bo; Zhang, Yan-Li; Qi, Wei-Wei; Wan, Yong-Jie; Fan, Yi-Xuan; Wang, Feng

2011-04-01

Pig has always been the focus of establishing a big ungulate animal ES cell lines because of its convenient source, genetic similarity with humans, and their importance in animal husbandry, but little development is achieved. Induced pluripotent stem cells technology creates a new method of reprogramming somatic cells to pluripotent state. As the pig iPS cells is established and perfected, pig ES cells will be established in the coming years. The pig iPS cells will give a hint on other livestock ES cells. On the other hand, pig iPS cells can be used to improve the efficiency of transgenic cloning pigs to conduct effective breeding and conservation of breeds. It is particularly important that the pig iPS cells can provide new model for human medical research, a new donor cells for human tissue and organ engineering, and have extensive and far-reaching impact on the biomedical field. Here, we briefly review the major progress of iPS cells, and emphasize current state of pig iPS cells and its application prospect in biomedicine and animal husbandry in order to provide a useful reference for researchers working in this area.

RIDES: Robust Intrusion Detection System for IP-Based Ubiquitous Sensor Networks

PubMed Central

Amin, Syed Obaid; Siddiqui, Muhammad Shoaib; Hong, Choong Seon; Lee, Sungwon

2009-01-01

The IP-based Ubiquitous Sensor Network (IP-USN) is an effort to build the “Internet of things”. By utilizing IP for low power networks, we can benefit from existing well established tools and technologies of IP networks. Along with many other unresolved issues, securing IP-USN is of great concern for researchers so that future market satisfaction and demands can be met. Without proper security measures, both reactive and proactive, it is hard to envisage an IP-USN realm. In this paper we present a design of an IDS (Intrusion Detection System) called RIDES (Robust Intrusion DEtection System) for IP-USN. RIDES is a hybrid intrusion detection system, which incorporates both Signature and Anomaly based intrusion detection components. For signature based intrusion detection this paper only discusses the implementation of distributed pattern matching algorithm with the help of signature-code, a dynamically created attack-signature identifier. Other aspects, such as creation of rules are not discussed. On the other hand, for anomaly based detection we propose a scoring classifier based on the SPC (Statistical Process Control) technique called CUSUM charts. We also investigate the settings and their effects on the performance of related parameters for both of the components. PMID:22412321

RIDES: Robust Intrusion Detection System for IP-Based Ubiquitous Sensor Networks.

PubMed

Amin, Syed Obaid; Siddiqui, Muhammad Shoaib; Hong, Choong Seon; Lee, Sungwon

2009-01-01

The IP-based Ubiquitous Sensor Network (IP-USN) is an effort to build the "Internet of things". By utilizing IP for low power networks, we can benefit from existing well established tools and technologies of IP networks. Along with many other unresolved issues, securing IP-USN is of great concern for researchers so that future market satisfaction and demands can be met. Without proper security measures, both reactive and proactive, it is hard to envisage an IP-USN realm. In this paper we present a design of an IDS (Intrusion Detection System) called RIDES (Robust Intrusion DEtection System) for IP-USN. RIDES is a hybrid intrusion detection system, which incorporates both Signature and Anomaly based intrusion detection components. For signature based intrusion detection this paper only discusses the implementation of distributed pattern matching algorithm with the help of signature-code, a dynamically created attack-signature identifier. Other aspects, such as creation of rules are not discussed. On the other hand, for anomaly based detection we propose a scoring classifier based on the SPC (Statistical Process Control) technique called CUSUM charts. We also investigate the settings and their effects on the performance of related parameters for both of the components.

Chromatin Immunoprecipitation (ChIP) Protocol for Low-abundance Embryonic Samples.

PubMed

Rehimi, Rizwan; Bartusel, Michaela; Solinas, Francesca; Altmüller, Janine; Rada-Iglesias, Alvaro

2017-08-29

Chromatin immunoprecipitation (ChIP) is a widely-used technique for mapping the localization of post-translationally modified histones, histone variants, transcription factors, or chromatin-modifying enzymes at a given locus or on a genome-wide scale. The combination of ChIP assays with next-generation sequencing (i.e., ChIP-Seq) is a powerful approach to globally uncover gene regulatory networks and to improve the functional annotation of genomes, especially of non-coding regulatory sequences. ChIP protocols normally require large amounts of cellular material, thus precluding the applicability of this method to investigating rare cell types or small tissue biopsies. In order to make the ChIP assay compatible with the amount of biological material that can typically be obtained in vivo during early vertebrate embryogenesis, we describe here a simplified ChIP protocol in which the number of steps required to complete the assay were reduced to minimize sample loss. This ChIP protocol has been successfully used to investigate different histone modifications in various embryonic chicken and adult mouse tissues using low to medium cell numbers (5 x 10 4 - 5 x 10 5 cells). Importantly, this protocol is compatible with ChIP-seq technology using standard library preparation methods, thus providing global epigenomic maps in highly relevant embryonic tissues.

Speech transport for packet telephony and voice over IP

NASA Astrophysics Data System (ADS)

Baker, Maurice R.

1999-11-01

Recent advances in packet switching, internetworking, and digital signal processing technologies have converged to allow realizable practical implementations of packet telephony systems. This paper provides a tutorial on transmission engineering for packet telephony covering the topics of speech coding/decoding, speech packetization, packet data network transport, and impairments which may negatively impact end-to-end system quality. Particular emphasis is placed upon Voice over Internet Protocol given the current popularity and ubiquity of IP transport.

Very High-Speed Report File System

DTIC Science & Technology

1992-12-15

1.5 and 45 Mb/s and is expected 1 Introduction to reach 150 Mb/s. These new technologies pose some challenges to The Internet Protocol (IP) family (IP... Internet Engineering Task Force (IETF) has R taken up the issue, but a definitive answer is probably some time away. The basic issues are the choice of AAL...by an IEEE 802. la Subnetwork Access Protocol (SNAP) However, with a large number of networks all header. The third proposal identifies the protocol

Generation of an ICF syndrome model by efficient genome editing of human induced pluripotent stem cells using the CRISPR system.

PubMed

Horii, Takuro; Tamura, Daiki; Morita, Sumiyo; Kimura, Mika; Hatada, Izuho

2013-09-30

Genome manipulation of human induced pluripotent stem (iPS) cells is essential to achieve their full potential as tools for regenerative medicine. To date, however, gene targeting in human pluripotent stem cells (hPSCs) has proven to be extremely difficult. Recently, an efficient genome manipulation technology using the RNA-guided DNase Cas9, the clustered regularly interspaced short palindromic repeats (CRISPR) system, has been developed. Here we report the efficient generation of an iPS cell model for immunodeficiency, centromeric region instability, facial anomalies syndrome (ICF) syndrome using the CRISPR system. We obtained iPS cells with mutations in both alleles of DNA methyltransferase 3B (DNMT3B) in 63% of transfected clones. Our data suggest that the CRISPR system is highly efficient and useful for genome engineering of human iPS cells.

77 FR 2932 - Airworthiness Directives; Rolls-Royce plc (RR) Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-20

...-pressure (IP) compressor rotor shaft rear balance land for cracks, which could lead to engine failure. This... and when in the shop, repetitive eddy current inspections (ECIs) for cracks on the rear balance land... for cracks on the rear balance land. That NPRM also proposed certain optional terminating actions...

Research of x-ray nondestructive detector for high-speed running conveyor belt with steel wire ropes

NASA Astrophysics Data System (ADS)

Wang, Junfeng; Miao, Changyun; Wang, Wei; Lu, Xiaocui

2008-03-01

An X-ray nondestructive detector for high-speed running conveyor belt with steel wire ropes is researched in the paper. The principle of X-ray nondestructive testing (NDT) is analyzed, the general scheme of the X-ray nondestructive testing system is proposed, and the nondestructive detector for high-speed running conveyor belt with steel wire ropes is developed. The hardware of system is designed with Xilinx's VIRTEX-4 FPGA that embeds PowerPC and MAC IP core, and its network communication software based on TCP/IP protocol is programmed by loading LwIP to PowerPC. The nondestructive testing of high-speed conveyor belt with steel wire ropes and network transfer function are implemented. It is a strong real-time system with rapid scanning speed, high reliability and remotely nondestructive testing function. The nondestructive detector can be applied to the detection of product line in industry.

Interoperation of an UHF RFID Reader and a TCP/IP Device via Wired and Wireless Links

PubMed Central

Lee, Sang Hoon; Jin, Ik Soo

2011-01-01

A main application in radio frequency identification (RFID) sensor networks is the function that processes real-time tag information after gathering the required data from multiple RFID tags. The component technologies that contain an RFID reader, called the interrogator, which has a tag chip, processors, coupling antenna, and a power management system have advanced significantly over the last decade. This paper presents a system implementation for interoperation between an UHF RFID reader and a TCP/IP device that is used as a gateway. The proposed system consists of an UHF RFID tag, an UHF RFID reader, an RF end-device, an RF coordinator, and a TCP/IP I/F. The UHF RFID reader, operating at 915 MHz, is compatible with EPC Class-0/Gen1, Class-1/Gen1 and 2, and ISO18000-6B. In particular, the UHF RFID reader can be combined with the RF end-device/coordinator for a ZigBee (IEEE 802.15.4) interface, which is a low-power wireless standard. The TCP/IP device communicates with the RFID reader via wired links. On the other hand, it is connected to the ZigBee end-device via wireless links. The web based test results show that the developed system can remotely recognize information of multiple tags through the interoperation between the RFID reader and the TCP/IP device. PMID:22346665

Interoperation of an UHF RFID reader and a TCP/IP device via wired and wireless links.

PubMed

Lee, Sang Hoon; Jin, Ik Soo

2011-01-01

A main application in radio frequency identification (RFID) sensor networks is the function that processes real-time tag information after gathering the required data from multiple RFID tags. The component technologies that contain an RFID reader, called the interrogator, which has a tag chip, processors, coupling antenna, and a power management system have advanced significantly over the last decade. This paper presents a system implementation for interoperation between an UHF RFID reader and a TCP/IP device that is used as a gateway. The proposed system consists of an UHF RFID tag, an UHF RFID reader, an RF end-device, an RF coordinator, and a TCP/IP I/F. The UHF RFID reader, operating at 915 MHz, is compatible with EPC Class-0/Gen1, Class-1/Gen1 and 2, and ISO18000-6B. In particular, the UHF RFID reader can be combined with the RF end-device/coordinator for a ZigBee (IEEE 802.15.4) interface, which is a low-power wireless standard. The TCP/IP device communicates with the RFID reader via wired links. On the other hand, it is connected to the ZigBee end-device via wireless links. The web based test results show that the developed system can remotely recognize information of multiple tags through the interoperation between the RFID reader and the TCP/IP device.

76 FR 75442 - Airworthiness Directives; Quest Aircraft Design, LLC Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-02

... right-hand side of the engine bypass door attachment. This condition, if not corrected, could lead to an... Directorate, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at... where a loose IPS bolt was found on the right-hand side of the engine bypass door attachment on Quest...

Standardization efforts in IP telephony

NASA Astrophysics Data System (ADS)

Sengodan, Senthil; Bansal, Raj

1999-11-01

The recent interest in IP telephony has led to a tremendous increase of standardization activities in the area. The three main standards bodies in the area of IP telephony are the International Telecommunication Union's (ITU-T) Study Group (SG) 16, the Internet Engineering Task Force (IETF) and the European Telecommunication Standards Institute's (ETSI) TIPHON project. In addition, forums such as the International Multimedia Teleconferencing Consortium (IMTC), the Intelligent Network Forum (INF), the International Softswitch Consortium (ISC), the Electronic Computer Telephony Forum (ECTF), and the MIT's Internet Telephony Consortium (ITC) are looking into various other aspects that aim at the growth of this industry. This paper describes the main tasks (completed and in progress) undertaken by these organizations. In describing such work, an overview of the underlying technology is also provided.

Flexoelectric effect in an in-plane switching (IPS) liquid crystal cell for low-power consumption display devices

NASA Astrophysics Data System (ADS)

Kim, Min Su; Bos, Philip J.; Kim, Dong-Woo; Yang, Deng-Ke; Lee, Joong Hee; Lee, Seung Hee

2016-10-01

Technology of displaying static images in portable displays, advertising panels and price tags pursues significant reduction in power consumption and in product cost. Driving at a low-frequency electric field in fringe-field switching (FFS) mode can be one of the efficient ways to save powers of the recent portable devices, but a serious drop of image-quality, so-called image-flickering, has been found in terms of the coupling of elastic deformation to not only quadratic dielectric effect but linear flexoelectric effect. Despite of the urgent requirement of solving the issue, understanding of such a phenomenon is yet vague. Here, we thoroughly analyze and firstly report the flexoelectric effect in in-plane switching (IPS) liquid crystal cell. The effect takes place on the area above electrodes due to splay and bend deformations of nematic liquid crystal along oblique electric fields, so that the obvious spatial shift of the optical transmittance is experimentally observed and is clearly demonstrated based on the relation between direction of flexoelectric polarization and electric field polarity. In addition, we report that the IPS mode has inherent characteristics to solve the image-flickering issue in the low-power consumption display in terms of the physical property of liquid crystal material and the electrode structure.

Flexoelectric effect in an in-plane switching (IPS) liquid crystal cell for low-power consumption display devices.

PubMed

Kim, Min Su; Bos, Philip J; Kim, Dong-Woo; Yang, Deng-Ke; Lee, Joong Hee; Lee, Seung Hee

2016-10-12

Technology of displaying static images in portable displays, advertising panels and price tags pursues significant reduction in power consumption and in product cost. Driving at a low-frequency electric field in fringe-field switching (FFS) mode can be one of the efficient ways to save powers of the recent portable devices, but a serious drop of image-quality, so-called image-flickering, has been found in terms of the coupling of elastic deformation to not only quadratic dielectric effect but linear flexoelectric effect. Despite of the urgent requirement of solving the issue, understanding of such a phenomenon is yet vague. Here, we thoroughly analyze and firstly report the flexoelectric effect in in-plane switching (IPS) liquid crystal cell. The effect takes place on the area above electrodes due to splay and bend deformations of nematic liquid crystal along oblique electric fields, so that the obvious spatial shift of the optical transmittance is experimentally observed and is clearly demonstrated based on the relation between direction of flexoelectric polarization and electric field polarity. In addition, we report that the IPS mode has inherent characteristics to solve the image-flickering issue in the low-power consumption display in terms of the physical property of liquid crystal material and the electrode structure.

Oral nutritional support can shorten the duration of parenteral hydration in end-of-life cancer patients: a randomized controlled trial.

PubMed

Ishiki, Hiroto; Iwase, Satoru; Gyoda, Yasuaki; Kanai, Yoshiaki; Ariyoshi, Keisuke; Miyaji, Tempei; Tahara, Yukiko; Kawaguchi, Takashi; Chinzei, Mieko; Yamaguchi, Takuhiro

2015-01-01

Tube feeding or hydration is often considered for end-of-life cancer patients despite the negative effects on quality of life. The efficacy of oral nutritional support in this setting is unknown. We conducted a randomized trial to compare the efficacies of an amino acid jelly, Inner Power® (IP), and a liquid enteral product, Ensure Liquid® (EL), in terminally ill cancer patients. We randomly assigned patients to 3 arms: EL, IP, and EL+IP. The primary endpoint was drip infusion in vein (DIV)-free survival, which was defined as the duration from nutritional support initiation to administration of parenteral hydration. Twenty-seven patients were enrolled in the study, of whom 21 were included in the intention-to-treat analysis. The median age of the subjects was 69 yr. There were significant differences between the arms with regard to the median DIV-free survival (0.5, 6.0, and 4.5 days in the EL, IP, and EL + IP arms, respectively; P = 0.05). The median overall survival was 7, 9, and 8 days in the EL, IP, and EL + IP arms, respectively. IP may shorten the duration of parenteral hydration in terminally ill cancer patients and does not affect their survival.

Observations of Interplanetary Scintillation (IPS) Using the Mexican Array Radio Telescope (MEXART)

NASA Astrophysics Data System (ADS)

Mejia-Ambriz, J. C.; Villanueva-Hernandez, P.; Gonzalez-Esparza, J. A.; Aguilar-Rodriguez, E.; Jeyakumar, S.

2010-08-01

The Mexican Array Radio Telescope (MEXART) consists of a 64×64 (4096) full-wavelength dipole antenna array, operating at 140 MHz, with a bandwidth of 2 MHz, occupying about 9660 square meters (69 m × 140 m) ( http://www.mexart.unam.mx ). This is a dedicated radio array for Interplanetary Scintillation (IPS) observations located at latitude 19°48'N, longitude 101°41'W. We characterize the performance of the system. We report the first IPS observations with the instrument, employing a Butler Matrix (BM) of 16×16 ports, fed by 16 east - west lines of 64 dipoles (1/4 of the total array). The BM displays a radiation pattern of 16 beams at different declinations (from -48, to +88 degrees). We present a list of 19 strong IPS radio sources (having at least 3 σ in power gain) detected by the instrument. We report the power spectral analysis procedure of the intensity fluctuations. The operation of MEXART will allow us a better coverage of solar wind disturbances, complementing the data provided by the other, previously built, instruments.

Video over IP design guidebook.

DOT National Transportation Integrated Search

2009-12-01

Texas Department of Transportation (TxDOT) engineers are responsible for the design, evaluation, and : implementation of video solutions across the entire state. These installations occur with vast differences in : requirements, expectations, and con...

Study on improved Ip-iq APF control algorithm and its application in micro grid

NASA Astrophysics Data System (ADS)

Xie, Xifeng; Shi, Hua; Deng, Haiyingv

2018-01-01

In order to enhance the tracking velocity and accuracy of harmonic detection by ip-iq algorithm, a novel ip-iq control algorithm based on the Instantaneous reactive power theory is presented, the improved algorithm adds the lead correction link to adjust the zero point of the detection system, the Fuzzy Self-Tuning Adaptive PI control is introduced to dynamically adjust the DC-link Voltage, which meets the requirement of the harmonic compensation of the micro grid. Simulation and experimental results verify the proposed method is feasible and effective in micro grid.

Chromatin Immunoprecipitation Sequencing (ChIP-Seq) for Transcription Factors and Chromatin Factors in Arabidopsis thaliana Roots: From Material Collection to Data Analysis.

PubMed

Cortijo, Sandra; Charoensawan, Varodom; Roudier, François; Wigge, Philip A

2018-01-01

Chromatin immunoprecipitation combined with next-generation sequencing (ChIP-seq) is a powerful technique to investigate in vivo transcription factor (TF) binding to DNA, as well as chromatin marks. Here we provide a detailed protocol for all the key steps to perform ChIP-seq in Arabidopsis thaliana roots, also working on other A. thaliana tissues and in most non-ligneous plants. We detail all steps from material collection, fixation, chromatin preparation, immunoprecipitation, library preparation, and finally computational analysis based on a combination of publicly available tools.

Order Without Intellectual Property Law: Open Science in Influenza.

PubMed

Kapczynski, Amy

Today, intellectual property (IP) scholars accept that IP as an approach to information production has serious limits. But what lies beyond IP? A new literature on "intellectual production without IP" (or "IP without IP") has emerged to explore this question, but its examples and explanations have yet to convince skeptics. This Article reorients this new literature via a study of a hard case: a global influenza virus-sharing network that has for decades produced critically important information goods, at significant expense, and in a loose-knit group--all without recourse to IP. I analyze the Network as an example of "open science," a mode of information production that differs strikingly from conventional IP, and yet that successfully produces important scientific goods in response to social need. The theory and example developed here refute the most powerful criticisms of the emerging "IP without IP" literature, and provide a stronger foundation for this important new field. Even where capital costs are high, creation without IP can be reasonably effective in social terms, if it can link sources of funding to reputational and evaluative feedback loops like those that characterize open science. It can also be sustained over time, even by loose-knit groups and where the stakes are high, because organizations and other forms of law can help to stabilize cooperation. I also show that contract law is well suited to modes of information production that rely upon a "supply side" rather than "demand side" model. In its most important instances, "order without IP" is not order without governance, nor order without law. Recognizing this can help us better ground this new field, and better study and support forms of knowledge production that deserve our attention, and that sometimes sustain our very lives.

Development of a video over IP guidebook.

DOT National Transportation Integrated Search

2009-09-01

Texas Department of Transportation (TxDOT) engineers are responsible for the design, evaluation, and implementation of video solutions across the entire state. These installations occur with vast differences in requirements, expectations, and constra...

Understanding the Relationship Between Female Sex Workers and Their Intimate Partners: Lessons and Initial Findings From Participatory Research in North Karnataka, South India.

PubMed

Bhattacharjee, Parinita; Campbell, Linda; Thalinja, Raghavendra; Nair, Sapna; Doddamane, Mahesh; Ramanaik, Satyanarayana; Isac, Shajy; Beattie, Tara S

2018-04-01

While traditional HIV prevention programs with female sex workers (FSWs) in Karnataka, India, have focused on reducing HIV transmission between FSWs and clients through increased condom use, these programs have not fully addressed the transmission risk between FSWs and their nonpaying intimate partners (IPs). Condom use is infrequent and violence is recurrent in these relationships: Furthermore, there is little evidence on the precise nature of FSW-IP relationships. Our study addresses this knowledge gap to inform HIV programs targeted at FSWs. A series of workshops, using participatory tools, was held to explore FSW-IP relationships; 31 FSWs and 37 IPs participated. Three aspects of FSW-IP relationships were examined: how FSWs and IPs understand and interpret their relationships, factors influencing condom use, and the role of violence and its consequences. FSWs wish to be perceived as their IPs' wives, while IPs expect their FSW partners to accept their dominance in the relationship. Nonuse of condoms signals fidelity and elevates the status of the relationship almost to that of marriage, which helps FSWs enter the category of "good" (married) women. Tolerating and accepting violence in these relationships is normative, as in other marital relationships; IPs justify violence as necessary to establish and maintain their power within the relationship. Both FSWs and IPs value their relationships despite the high degree of risk posed by low condom use and high levels of violence. Implications for program design include addressing current norms around masculinity and gender roles, and improving communication within relationships.

Interplanetary scintillation at large elongation angles: Response to solar wind density structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erskine, F.T.; Cronyn, W.M.; Shawhan, S.D.

1978-09-01

Synoptic interplanetary scintillation (IPS) index measurements were taken at 34.3 MHz during May-December 1974 using the University of Iowa Coca Cross radiotelescope on a 'grid' of 150 selected radio sources covering solar elongation angles up to 180/sup 0/. Over 80 of these sources displayed definite IPS. The solar elongation dependence of the 34.3-MHz IPS index is consistent with the elongation angle dependence measured at higher frequencies. Large enhancements (factors of> or approx. =2) of the IPS index are found to coincide with the solar wind (proton density increases greater than 10 cm/sup -3/ as measured by Imp 7 and 8more » for nearly all observed IPS sources throughout the sky. These 'all-sky' IPS enhancements appear to be caused by incresed contributions to the scintillation power by turbulent plasma in regions close to the earth (< or approx. =0.3AU) in all directions. Correlation analysis confirms the IPS response to solar wind density and indicates that the events are due primarily to the corotating solar wind turbulent plasma structures which dominated the interplanetary medium during 1974. The expected IPS space-time signature for a simple model of an approaching corotating turbulent structure is not apparent in our observations. In some cases, the enhancement variatons can be attributed to structural differences in the solar wind density turbulence in and out of the ecliptic.« less

Hybrid model for wireless mobility management using IPv6

NASA Astrophysics Data System (ADS)

Howie, Douglas P.; Sun, Junzhao; Koivisto, Antti T.

2001-07-01

Within the coming decade, there will be a dramatic increase in the availability of inexpensive, computationally powerful mobile devices running applications which use the Internet Protocol (IP) to access multimedia services over broad-band wireless connections. To this end, there has been extensive research and standardization in the areas of Mobile IP and IPv6. The purpose of this paper is to apply this work to the issues involved in designing a mobility model able to adapt to different wireless mobile IP scenarios. We describe the usefulness of this model in the 4th generation mobile multimedia systems to come. This new model has been synthesized through a comparative analysis of current mobile IP models where particular attention has been given to the problems of mobile IP handoff and mobility management and their impact on QoS. By applying a unique perspective to these problems, our model is used to set a roadmap for future mobile IPv6 testbed construction.

Hardware-software face detection system based on multi-block local binary patterns

NASA Astrophysics Data System (ADS)

Acasandrei, Laurentiu; Barriga, Angel

2015-03-01

Face detection is an important aspect for biometrics, video surveillance and human computer interaction. Due to the complexity of the detection algorithms any face detection system requires a huge amount of computational and memory resources. In this communication an accelerated implementation of MB LBP face detection algorithm targeting low frequency, low memory and low power embedded system is presented. The resulted implementation is time deterministic and uses a customizable AMBA IP hardware accelerator. The IP implements the kernel operations of the MB-LBP algorithm and can be used as universal accelerator for MB LBP based applications. The IP employs 8 parallel MB-LBP feature evaluators cores, uses a deterministic bandwidth, has a low area profile and the power consumption is ~95 mW on a Virtex5 XC5VLX50T. The resulted implementation acceleration gain is between 5 to 8 times, while the hardware MB-LBP feature evaluation gain is between 69 and 139 times.

Architectural and engineering issues for building an optical Internet

NASA Astrophysics Data System (ADS)

St. Arnaud, Bill

1998-10-01

Recent developments in high density Wave Division Multiplexing fiber systems allows for the deployment of a dedicated optical Internet network for large volume backbone pipes that does not require an underlying multi-service SONET/SDH and ATM transport protocol. Some intrinsic characteristics of Internet traffic such as its self similar nature, server bound congestion, routing and data asymmetry allow for highly optimized traffic engineered networks using individual wavelengths. By transmitting GigaBit Ethernet or SONET/SDH frames natively over WDM wavelengths that directly interconnect high performance routers the original concept of the Internet as an intrinsically survivable datagram network is possible. Traffic engineering, restoral, protection and bandwidth management of the network must now be carried out at the IP layer and so new routing or switching protocols such as MPLS that allow for uni- directional paths with fast restoral and protection at the IP layer become essential for a reliable production network. The deployment of high density WDM municipal and campus networks also gives carriers and ISPs the flexibility to offer customers as integrated and seamless set of optical Internet services.

Designing of routing algorithms in autonomous distributed data transmission system for mobile computing devices with ‘WiFi-Direct’ technology

NASA Astrophysics Data System (ADS)

Nikitin, I. A.; Sherstnev, V. S.; Sherstneva, A. I.; Botygin, I. A.

2017-02-01

The results of the research of existent routing protocols in wireless networks and their main features are discussed in the paper. Basing on the protocol data, the routing protocols in wireless networks, including search routing algorithms and phone directory exchange algorithms, are designed with the ‘WiFi-Direct’ technology. Algorithms without IP-protocol were designed, and that enabled one to increase the efficiency of the algorithms while working only with the MAC-addresses of the devices. The developed algorithms are expected to be used in the mobile software engineering with the Android platform taken as base. Easier algorithms and formats of the well-known route protocols, rejection of the IP-protocols enables to use the developed protocols on more primitive mobile devices. Implementation of the protocols to the engineering industry enables to create data transmission networks among working places and mobile robots without any access points.

Human iPS cell-derived astrocyte transplants preserve respiratory function after spinal cord injury

PubMed Central

Li, Ke; Javed, Elham; Scura, Daniel; Hala, Tamara J.; Seetharam, Suneil; Falnikar, Aditi; Richard, Jean-Philippe; Chorath, Ashley; Maragakis, Nicholas J.; Wright, Megan C.; Lepore, Angelo C.

2015-01-01

Transplantation-based replacement of lost and/or dysfunctional astrocytes is a promising therapy for spinal cord injury (SCI) that has not been extensively explored, despite the integral roles played by astrocytes in the central nervous system (CNS). Induced pluripotent stem (iPS) cells are a clinically-relevant source of pluripotent cells that both avoid ethical issues of embryonic stem cells and allow for homogeneous derivation of mature cell types in large quantities, potentially in an autologous fashion. Despite their promise, the iPS cell field is in its infancy with respect to evaluating in vivo graft integration and therapeutic efficacy in SCI models. Astrocytes express the major glutamate transporter, GLT1, which is responsible for the vast majority of glutamate uptake in spinal cord. Following SCI, compromised GLT1 expression/function can increase susceptibility to excitotoxicity. We therefore evaluated intraspinal transplantation of human iPS cell-derived astrocytes (hIPSAs) following cervical contusion SCI as a novel strategy for reconstituting GLT1 expression and for protecting diaphragmatic respiratory neural circuitry. Transplant-derived cells showed robust long-term survival post-injection and efficiently differentiated into astrocytes in injured spinal cord of both immunesuppressed mice and rats. However, the majority of transplant-derived astrocytes did not express high levels of GLT1, particularly at early times post-injection. To enhance their ability to modulate extracellular glutamate levels, we engineered hIPSAs with lentivirus to constitutively express GLT1. Overexpression significantly increased GLT1 protein and functional GLT1-mediated glutamate uptake levels in hIPSAs both in vitro and in vivo post-transplantation. Compared to human fibroblast control and unmodified hIPSA transplantation, GLT1-overexpressing hIPSAs reduced (1) lesion size within the injured cervical spinal cord, (2) morphological denervation by respiratory phrenic motor neurons at the diaphragm neuromuscular junction, and (3) functional diaphragm denervation as measured by recording of spontaneous EMGs and evoked compound muscle action potentials. Our findings demonstrate that hiPSA transplantation is a therapeutically-powerful approach for SCI. PMID:26216662

Human iPS cell-derived astrocyte transplants preserve respiratory function after spinal cord injury.

PubMed

Li, Ke; Javed, Elham; Scura, Daniel; Hala, Tamara J; Seetharam, Suneil; Falnikar, Aditi; Richard, Jean-Philippe; Chorath, Ashley; Maragakis, Nicholas J; Wright, Megan C; Lepore, Angelo C

2015-09-01

Transplantation-based replacement of lost and/or dysfunctional astrocytes is a promising therapy for spinal cord injury (SCI) that has not been extensively explored, despite the integral roles played by astrocytes in the central nervous system (CNS). Induced pluripotent stem (iPS) cells are a clinically-relevant source of pluripotent cells that both avoid ethical issues of embryonic stem cells and allow for homogeneous derivation of mature cell types in large quantities, potentially in an autologous fashion. Despite their promise, the iPS cell field is in its infancy with respect to evaluating in vivo graft integration and therapeutic efficacy in SCI models. Astrocytes express the major glutamate transporter, GLT1, which is responsible for the vast majority of glutamate uptake in spinal cord. Following SCI, compromised GLT1 expression/function can increase susceptibility to excitotoxicity. We therefore evaluated intraspinal transplantation of human iPS cell-derived astrocytes (hIPSAs) following cervical contusion SCI as a novel strategy for reconstituting GLT1 expression and for protecting diaphragmatic respiratory neural circuitry. Transplant-derived cells showed robust long-term survival post-injection and efficiently differentiated into astrocytes in injured spinal cord of both immunesuppressed mice and rats. However, the majority of transplant-derived astrocytes did not express high levels of GLT1, particularly at early times post-injection. To enhance their ability to modulate extracellular glutamate levels, we engineered hIPSAs with lentivirus to constitutively express GLT1. Overexpression significantly increased GLT1 protein and functional GLT1-mediated glutamate uptake levels in hIPSAs both in vitro and in vivo post-transplantation. Compared to human fibroblast control and unmodified hIPSA transplantation, GLT1-overexpressing hIPSAs reduced (1) lesion size within the injured cervical spinal cord, (2) morphological denervation by respiratory phrenic motor neurons at the diaphragm neuromuscular junction, and (3) functional diaphragm denervation as measured by recording of spontaneous EMGs and evoked compound muscle action potentials. Our findings demonstrate that hiPSA transplantation is a therapeutically-powerful approach for SCI. Copyright © 2015 Elsevier Inc. All rights reserved.

Bayesian reconstruction of transmission within outbreaks using genomic variants.

PubMed

De Maio, Nicola; Worby, Colin J; Wilson, Daniel J; Stoesser, Nicole

2018-04-01

Pathogen genome sequencing can reveal details of transmission histories and is a powerful tool in the fight against infectious disease. In particular, within-host pathogen genomic variants identified through heterozygous nucleotide base calls are a potential source of information to identify linked cases and infer direction and time of transmission. However, using such data effectively to model disease transmission presents a number of challenges, including differentiating genuine variants from those observed due to sequencing error, as well as the specification of a realistic model for within-host pathogen population dynamics. Here we propose a new Bayesian approach to transmission inference, BadTrIP (BAyesian epiDemiological TRansmission Inference from Polymorphisms), that explicitly models evolution of pathogen populations in an outbreak, transmission (including transmission bottlenecks), and sequencing error. BadTrIP enables the inference of host-to-host transmission from pathogen sequencing data and epidemiological data. By assuming that genomic variants are unlinked, our method does not require the computationally intensive and unreliable reconstruction of individual haplotypes. Using simulations we show that BadTrIP is robust in most scenarios and can accurately infer transmission events by efficiently combining information from genetic and epidemiological sources; thanks to its realistic model of pathogen evolution and the inclusion of epidemiological data, BadTrIP is also more accurate than existing approaches. BadTrIP is distributed as an open source package (https://bitbucket.org/nicofmay/badtrip) for the phylogenetic software BEAST2. We apply our method to reconstruct transmission history at the early stages of the 2014 Ebola outbreak, showcasing the power of within-host genomic variants to reconstruct transmission events.

Power Balance Modeling and Validation for ST Startup Using Local Helicity Injection

NASA Astrophysics Data System (ADS)

Barr, J. L.; Bodner, G. M.; Bongard, M. W.; Burke, M. G.; Fonck, R. J.; Hinson, E. T.; Perry, J. M.; Reusch, J. A.; Schlossberg, D. J.

2015-11-01

Local Helicity Injection (LHI) uses localized current injectors for routine Ip<0.18 MA non-solenoidal startup on the Pegasus ST. A power-balance model is under development for predictive Ip t using helicity-balance to quantify LHI's effective current drive, Veff. Analytic formulas for low-A plasma inductance and vertical field are used to account for the inductive effects of dynamic shape evolution. These formulas are being validated against magnetic reconstructions of LHI discharges with varied shape evolutions. Initial results match experimental Ip t within 20 kA with assumed shaping and average resistivity (Spitzer, Te = 60 eV). Geometric effects and inductive drive provide 2.0 V along with Veff = 0.3 V to balance 1.1 V of resistive losses and 1.2 V inductive reactance to ramping Ip. The model is especially sensitive to resistivity when Te<150 eV. Initial Thomson Scattering results give core Te = 72 +/-22 eV, and at times suggest higher central electron energies. Spatial and temporal scans are underway to quantify LHI plasma resistivity and transport. MA-class startup in NSTX-U will require increased area (Ainj >= 40 cm2) LHI systems that play a larger role in current drive than geometric effects, with Veff dropping from >10 V to on-par with inductive effects. This regime is accessed in Pegasus at Ip ≅ 300 kA. Work supported by US DOE grants DE-FG02-96ER54375 and DE-SC0006928.

65nm RadSafe™ Technology for RC64 and Advanced SOCs

NASA Astrophysics Data System (ADS)

Liran, Tuvia; Ginosar, Ran; Lange, Fredy; Mandler, Alberto; Aviely, Peleg; Meirov, Henri; Goldberg, Michael; Meister, Zeev; Oliel, Mickey

2015-09-01

The trend of scaling of microelectronic provides certain advantages for space components, as well as some challenges. It enables implementing highly integrated and high performance ASICs, reducing power, area and weight. Scaling also improves the immunity to TID and SEL in most cases, but increases soft error rate significantly. Ramon Chips adopted the 65nm technology for implementing RC64 [1,2], a 64 core DSP for space applications, and for making other future products. The 65nm process node is widely used, very mature, and supported by wide range of IP providers. Thus the need for full custom design of cores and IPs is minimized, and radiation hardening is achievable by mitigating the radiation effects on the available IPs, and developing proprietary IPs only for complementing the available IPs. The RadSafe_65TM technology includes hardened standard cells and I/O libraries, methods for mitigation of radiation effects in COTS IP cores (SRAM, PLL, SERDES, DDR2/3 interface) and adding unique cores for monitoring radiation effects and junction temperature. We had developed RADIC6, a technology development vehicle, for verification of all hard cores and verification of the methodologies and design flow required for RC64. RADIC6 includes the test structures for characterizing the IP cores for immunity to all radiation effects. This paper describes the main elements and IP cores of RadSafe_65TM, as well as the contents of RADIC6 test chip.

A System Implementation for Cooperation between UHF RFID Reader and TCP/IP Device

NASA Astrophysics Data System (ADS)

Lee, Sang Hoon; Jin, Ik Soo

This paper presents a system implementation for cooperation between UHF RFID reader and TCP/IP device that can be used as a home gateway. The system consists of an UHF RFID tag, an UHF RFID reader, a RF end-device, a RF coordinator and a TCP/IP I/F. The UHF RFID reader is compatible with EPC Class-0/Gen1, Class-1/Gen1, 2 and ISO18000-6B, operating at the 915MHz. In particular, UHF RFID reader can be combined with a RF end device/coordinator for ZigBee(IEEE 802.15.4) interface which is low power wireless standard. The TCP/IP device is communicated with RFID reader via wired type. On the other hand, it is connected with ZigBee end-device via wireless type. The experimental results show that the developed system can provide the right networking.

Security Primitives for Reconfigurable Hardware-Based Systems

DTIC Science & Technology

2010-05-01

work, we propose security primitives using ideas centered around the notion of “moats and drawbridges .” The primitives encompass four design properties...Santa Bar- bara, CA 93106; email: sherwood@cs.ucsb.edu; R. Kastner, Department of Computer Science and Engineering , University of California, San...fingerprint reader), the other to control the ethernet IP core—and an AES encryption engine used by both of the processor cores. These cores are all implemented

Fast rerouting schemes for protected mobile IP over MPLS networks

NASA Astrophysics Data System (ADS)

Wen, Chih-Chao; Chang, Sheng-Yi; Chen, Huan; Chen, Kim-Joan

2005-10-01

Fast rerouting is a critical traffic engineering operation in the MPLS networks. To implement the Mobile IP service over the MPLS network, one can collaborate with the fast rerouting operation to enhance the availability and survivability. MPLS can protect critical LSP tunnel between Home Agent (HA) and Foreign Agent (FA) using the fast rerouting scheme. In this paper, we propose a simple but efficient algorithm to address the triangle routing problem for the Mobile IP over the MPLS networks. We consider this routing issue as a link weighting and capacity assignment (LW-CA) problem. The derived solution is used to plan the fast restoration mechanism to protect the link or node failure. In this paper, we first model the LW-CA problem as a mixed integer optimization problem. Our goal is to minimize the call blocking probability on the most congested working truck for the mobile IP connections. Many existing network topologies are used to evaluate the performance of our scheme. Results show that our proposed scheme can obtain the best performance in terms of the smallest blocking probability compared to other schemes.

An Improved Harmonic Current Detection Method Based on Parallel Active Power Filter

NASA Astrophysics Data System (ADS)

Zeng, Zhiwu; Xie, Yunxiang; Wang, Yingpin; Guan, Yuanpeng; Li, Lanfang; Zhang, Xiaoyu

2017-05-01

Harmonic detection technology plays an important role in the applications of active power filter. The accuracy and real-time performance of harmonic detection are the precondition to ensure the compensation performance of Active Power Filter (APF). This paper proposed an improved instantaneous reactive power harmonic current detection algorithm. The algorithm uses an improved ip -iq algorithm which is combined with the moving average value filter. The proposed ip -iq algorithm can remove the αβ and dq coordinate transformation, decreasing the cost of calculation, simplifying the extraction process of fundamental components of load currents, and improving the detection speed. The traditional low-pass filter is replaced by the moving average filter, detecting the harmonic currents more precisely and quickly. Compared with the traditional algorithm, the THD (Total Harmonic Distortion) of the grid currents is reduced from 4.41% to 3.89% for the simulations and from 8.50% to 4.37% for the experiments after the improvement. The results show the proposed algorithm is more accurate and efficient.

Target mimicry provides a new mechanism for regulation of microRNA activity.

PubMed

Franco-Zorrilla, José Manuel; Valli, Adrián; Todesco, Marco; Mateos, Isabel; Puga, María Isabel; Rubio-Somoza, Ignacio; Leyva, Antonio; Weigel, Detlef; García, Juan Antonio; Paz-Ares, Javier

2007-08-01

MicroRNAs (miRNA) regulate key aspects of development and physiology in animals and plants. These regulatory RNAs act as guides of effector complexes to recognize specific mRNA sequences based on sequence complementarity, resulting in translational repression or site-specific cleavage. In plants, most miRNA targets are cleaved and show almost perfect complementarity with the miRNAs around the cleavage site. Here, we examined the non-protein coding gene IPS1 (INDUCED BY PHOSPHATE STARVATION 1) from Arabidopsis thaliana. IPS1 contains a motif with sequence complementarity to the phosphate (Pi) starvation-induced miRNA miR-399, but the pairing is interrupted by a mismatched loop at the expected miRNA cleavage site. We show that IPS1 RNA is not cleaved but instead sequesters miR-399. Thus, IPS1 overexpression results in increased accumulation of the miR-399 target PHO2 mRNA and, concomitantly, in reduced shoot Pi content. Engineering of IPS1 to be cleavable abolishes its inhibitory activity on miR-399. We coin the term 'target mimicry' to define this mechanism of inhibition of miRNA activity. Target mimicry can be generalized beyond the control of Pi homeostasis, as demonstrated using artificial target mimics.

A rapid assessment method to estimate the distribution of juvenile Chinook Salmon in tributary habitats using eDNA and occupancy estimation

USGS Publications Warehouse

Matter, A.; Falke, Jeffrey A.; López, J. Andres; Savereide, James W.

2018-01-01

Identification and protection of water bodies used by anadromous species are critical in light of increasing threats to fish populations, yet often challenging given budgetary and logistical limitations. Noninvasive, rapid‐assessment, sampling techniques may reduce costs and effort while increasing species detection efficiencies. We used an intrinsic potential (IP) habitat model to identify high‐quality rearing habitats for Chinook Salmon Oncorhynchus tshawytscha and select sites to sample throughout the Chena River basin, Alaska, for juvenile occupancy using an environmental DNA (eDNA) approach. Water samples were collected from 75 tributary sites in 2014 and 2015. The presence of Chinook Salmon DNA in water samples was assessed using a species‐specific quantitative PCR (qPCR) assay. The IP model predicted over 900 stream kilometers in the basin to support high‐quality (IP ≥ 0.75) rearing habitat. Occupancy estimation based on eDNA samples indicated that 80% and 56% of previously unsampled sites classified as high or low IP (IP < 0.75), respectively, were occupied. The probability of detection (p) of Chinook Salmon DNA from three replicate water samples was high (p = 0.76) but varied with drainage area (km2). A power analysis indicated high power to detect proportional changes in occupancy based on parameter values estimated from eDNA occupancy models, although power curves were not symmetrical around zero, indicating greater power to detect positive than negative proportional changes in occupancy. Overall, the combination of IP habitat modeling and occupancy estimation provided a useful, rapid‐assessment method to predict and subsequently quantify the distribution of juvenile salmon in previously unsampled tributary habitats. Additionally, these methods are flexible and can be modified for application to other species and in other locations, which may contribute towards improved population monitoring and management.

iASeq: integrative analysis of allele-specificity of protein-DNA interactions in multiple ChIP-seq datasets

PubMed Central

2012-01-01

Background ChIP-seq provides new opportunities to study allele-specific protein-DNA binding (ASB). However, detecting allelic imbalance from a single ChIP-seq dataset often has low statistical power since only sequence reads mapped to heterozygote SNPs are informative for discriminating two alleles. Results We develop a new method iASeq to address this issue by jointly analyzing multiple ChIP-seq datasets. iASeq uses a Bayesian hierarchical mixture model to learn correlation patterns of allele-specificity among multiple proteins. Using the discovered correlation patterns, the model allows one to borrow information across datasets to improve detection of allelic imbalance. Application of iASeq to 77 ChIP-seq samples from 40 ENCODE datasets and 1 genomic DNA sample in GM12878 cells reveals that allele-specificity of multiple proteins are highly correlated, and demonstrates the ability of iASeq to improve allelic inference compared to analyzing each individual dataset separately. Conclusions iASeq illustrates the value of integrating multiple datasets in the allele-specificity inference and offers a new tool to better analyze ASB. PMID:23194258

Analysis of ChIP-seq Data in R/Bioconductor.

PubMed

de Santiago, Ines; Carroll, Thomas

2018-01-01

The development of novel high-throughput sequencing methods for ChIP (chromatin immunoprecipitation) has provided a very powerful tool to study gene regulation in multiple conditions at unprecedented resolution and scale. Proactive quality-control and appropriate data analysis techniques are of critical importance to extract the most meaningful results from the data. Over the last years, an array of R/Bioconductor tools has been developed allowing researchers to process and analyze ChIP-seq data. This chapter provides an overview of the methods available to analyze ChIP-seq data based primarily on software packages from the open-source Bioconductor project. Protocols described in this chapter cover basic steps including data alignment, peak calling, quality control and data visualization, as well as more complex methods such as the identification of differentially bound regions and functional analyses to annotate regulatory regions. The steps in the data analysis process were demonstrated on publicly available data sets and will serve as a demonstration of the computational procedures routinely used for the analysis of ChIP-seq data in R/Bioconductor, from which readers can construct their own analysis pipelines.

Zeroth-order design report for the next linear collider. Volume 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raubenheimer, T.O.

This Zeroth-Order Design Report (ZDR) for the Next Linear Collider (NLC) has been completed as a feasibility study for a TeV-scale linear collider that incorporates a room-temperature accelerator powered by rf microwaves at 11.424 GHz--similar to that presently used in the SLC, but at four times the rf frequency. The purpose of this study is to examine the complete systems of such a collider, to understand how the parts fit together, and to make certain that every required piece has been included. The ``design`` presented here is not fully engineered in any sense, but to be assured that the NLCmore » can be built, attention has been given to a number of critical components and issues that present special challenges. More engineering and development of a number of mechanical and electrical systems remain to be done, but the conclusion of this study is that indeed the NLC is technically feasible and can be expected to reach the performance levels required to perform research at the TeV energy scale. Volume II covers the following: collimation systems; IP switch and big bend; final focus; the interaction region; multiple bunch issues; control systems; instrumentation; machine protection systems; NLC reliability considerations; NLC conventional facilities. Also included are four appendices on the following topics: An RF power source upgrade to the NLC; a second interaction region for gamma-gamma, gamma-electron; ground motion: theory and measurement; and beam-based feedback: theory and implementation.« less

Achieving Better Buying Power through Acquisition of Open Architecture Software Systems. Volume 2 Understanding Open Architecture Software Systems: Licensing and Security Research and Recommendations

DTIC Science & Technology

2016-01-06

of- breed software components and software products lines (SPLs) that are subject to different IP license and cybersecurity requirements. The... commercially priced closed source software components, to be used in the design, implementation, deployment, and evolution of open architecture (OA... breed software components and software products lines (SPLs) that are subject to different IP license and cybersecurity requirements. The Department

A Study of a Two Stage Maximum Power Point Tracking Control of a Photovoltaic System under Partially Shaded Insolation Conditions

NASA Astrophysics Data System (ADS)

Kobayashi, Kenji; Takano, Ichiro; Sawada, Yoshio

A photovoltaic array shows relatively low output power density, and has a greatly drooping Current-Voltage (I-V) characteristic. Therefore, Maximum Power Point Tracking (MPPT) control is used to maximize the output power of the array. Many papers have been reported in relation to MPPT. However, the Current-Power (I-P) curve sometimes shows multi-local maximum points mode under non-uniform insolation conditions. The operating point of the PV system tends to converge to a local maximum output point which is not the real maximal output point on the I-P curve. Some papers have been also reported, trying to avoid this difficulty. However most of those control systems become rather complicated. Then, the two stage MPPT control method is proposed in this paper to realize a relatively simple control system which can track the real maximum power point even under non-uniform insolation conditions. The feasibility of this control concept is confirmed for steady insolation as well as for rapidly changing insolation by simulation study using software PSIM and LabVIEW. In addition, simulated experiment confirms fundament al operation of the two stage MPPT control.

ASTRO-2 Spacelab Instrument Pointing System mission performance

NASA Technical Reports Server (NTRS)

Wessling, Francis C., III; Singh, S. P.

1995-01-01

This paper reports the performance of the Instrument Pointing System (IPS) that flew on the National Aeronautics and Space Administration (NASA) ASTRO-2 Spacelab mission aboard the Space Shuttle Endeavour in March 1995. The IPS provides a stabilizing platform for the ASTRO-2 instrument payload complement that consists of three main experiments (telescopes). The telescopes observe stellar targets in the universe within the ultraviolet portion of the electromagnetic spectrum that must be observed from beyond the earth's atmospheric filtering effects. The three main experiments for observation are the Hopkins Ultraviolet Telescope (HUT), the Ultraviolet Imaging Telescope (UIT), and the Wisconsin Ultraviolet Photo-Polarimetry Experiment (WUPPE). The HUT uses spectroscopy to obtain the structure and chemical makeup of ultraviolet targets. UIT is responsible for wide field photographing to capture the hidden view of the ultraviolet universe. The WUPPE gathers data on the polarization of the ultraviolet electromagnetic energy coming from the astronomical targets. The capability of IPS enables the experiments to 'see' faint celestial objects. A brief explanation of the IPS is given followed by a review of engineering efforts to improve IPS performance over the ASTRO-1 mission. The main focus of improvements was on enhancing the star acquisition capability through improved guide star selection, lab simulations, computer upgrades, data display systems improvements, and software modifications. A star simulator was developed in the lab to enable IPS to be simulated on the ground pre-mission with flight hardware and software in the loop. The paper concludes with results from the ASTRO-2 mission. The number of targets acquired and the IPS pointing accuracy/stability is reported along with recommendations for the future use of the Instrument Pointing System.

Improvement of the course “Management of intellectual property” based on the mixed state contract in the field of scientific R&D

NASA Astrophysics Data System (ADS)

Yakovlev, D.; Ageev, A.; Yushkov, E.; Bogatyreova, M.

2017-01-01

Intellectual property (IP) is one of the forms of storing knowledge - intangible assets of knowledge economy. The translation of IP knowledge to the young generation is one of the challenges of nuclear knowledge management. At the NRNU MEPhI (National Research Nuclear University MEPhI), the subject is studied within the framework of the academic course “Management of intellectual property. The aim of the course is to train qualified specialists, ready to use modern methods of strategic management of IP in commercial firms. The article is devoted to the strengthening and transfer of IP rights for scientific output application in industry and commerce. The state remains the main source that finances all the significant developments in the field of science and technology. Therefore, the primary task is to effectively utilize the R&D output created at the expense of the Federal budget, both within the state order and the estimated budget financing. Currently, there exist contradictions in the area of strengthening and transfer of rights for R&D in the field of science. The newly borne concept dealing with the strengthening of IP rights for the scientific R&D output, centers on the theory of a mixed state contract and is conveniently integrated with the academic course mentioned. Knowledge itself takes the form of IP, as soon as it becomes formalized. The academic course when supplemented with various approaches to strengthening and transfer of IP rights for the scientific R&D output certainly gives a better understanding of the commercialization process of the intellectual capital and structures relevance to intellectual property. The research material is integrated with the educational process, and the academic course “Management of intellectual property” is designed both for economic and engineering specialties.

A distributed control approach for power and energy management in a notional shipboard power system

NASA Astrophysics Data System (ADS)

Shen, Qunying

The main goal of this thesis is to present a power control module (PCON) based approach for power and energy management and to examine its control capability in shipboard power system (SPS). The proposed control scheme is implemented in a notional medium voltage direct current (MVDC) integrated power system (IPS) for electric ship. To realize the control functions such as ship mode selection, generator launch schedule, blackout monitoring, and fault ride-through, a PCON based distributed power and energy management system (PEMS) is developed. The control scheme is proposed as two-layer hierarchical architecture with system level on the top as the supervisory control and zonal level on the bottom as the decentralized control, which is based on the zonal distribution characteristic of the notional MVDC IPS that was proposed as one of the approaches for Next Generation Integrated Power System (NGIPS) by Norbert Doerry. Several types of modules with different functionalities are used to derive the control scheme in detail for the notional MVDC IPS. Those modules include the power generation module (PGM) that controls the function of generators, the power conversion module (PCM) that controls the functions of DC/DC or DC/AC converters, etc. Among them, the power control module (PCON) plays a critical role in the PEMS. It is the core of the control process. PCONs in the PEMS interact with all the other modules, such as power propulsion module (PPM), energy storage module (ESM), load shedding module (LSHED), and human machine interface (HMI) to realize the control algorithm in PEMS. The proposed control scheme is implemented in real time using the real time digital simulator (RTDS) to verify its validity. To achieve this, a system level energy storage module (SESM) and a zonal level energy storage module (ZESM) are developed in RTDS to cooperate with PCONs to realize the control functionalities. In addition, a load shedding module which takes into account the reliability of power supply (in terms of quality of service) is developed. This module can supply uninterruptible power to the mission critical loads. In addition, a multi-agent system (MAS) based framework is proposed to implement the PCON based PEMS through a hardware setup that is composed of MAMBA boards and FPGA interface. Agents are implemented using Java Agent DEvelopment Framework (JADE). Various test scenarios were tested to validate the approach.

Science spin: iPS cell research in the news.

PubMed

Caulfield, T; Rachul, C

2011-05-01

Big scientific developments have always been spun to meet particular social agendas. We have seen it in the context of global warming, nuclear power, and genetically modified organisms. But few stories illustrate the phenomenon of spin as well as the reaction, and concomitant media coverage, that surrounded the November 2007 announcement regarding the reprogramming of skin cells to produce cells with qualities comparable to those of human embryonic stem cells (hESCs) known as induced pluripotent stem (iPS) cells.

Anomalous diffusion of Ibuprofen in cyclodextrin nanosponge hydrogels: an HRMAS NMR study.

PubMed

Ferro, Monica; Castiglione, Franca; Punta, Carlo; Melone, Lucio; Panzeri, Walter; Rossi, Barbara; Trotta, Francesco; Mele, Andrea

2014-01-01

Ibuprofen sodium salt (IP) was encapsulated in cyclodextrin nanosponges (CDNS) obtained by cross-linking of β-cyclodextrin with ethylenediaminetetraacetic acid dianhydride (EDTAn) in two different preparations: CDNSEDTA 1:4 and 1:8, where the 1:n notation indicates the CD to EDTAn molar ratio. The entrapment of IP was achieved by swelling the two polymers with a 0.27 M solution of IP in D2O, leading to colourless, homogeneous hydrogels loaded with IP. The molecular environment and the transport properties of IP in the hydrogels were studied by high resolution magic angle spinning (HRMAS) NMR spectroscopy. The mean square displacement (MSD) of IP in the gels was obtained by a pulsed field gradient spin echo (PGSE) NMR pulse sequence at different observation times t d. The MSD is proportional to the observation time elevated to a scaling factor α. The α values define the normal Gaussian random motion (α = 1), or the anomalous diffusion (α < 1, subdiffusion, α > 1 superdiffusion). The experimental data here reported point out that IP undergoes subdiffusive regime in CDNSEDTA 1:4, while a slightly superdiffusive behaviour is observed in CDNSEDTA 1:8. The transition between the two dynamic regimes is triggered by the polymer structure. CDNSEDTA 1:4 is characterized by a nanoporous structure able to induce confinement effects on IP, thus causing subdiffusive random motion. CDNSEDTA 1:8 is characterized not only by nanopores, but also by dangling EDTA groups ending with ionized COO(-) groups. The negative potential provided by such groups to the polymer backbone is responsible for the acceleration effects on the IP anion thus leading to the superdiffusive behaviour observed. These results point out that HRMAS NMR spectroscopy is a powerful direct method for the assessment of the transport properties of a drug encapsulated in polymeric scaffolds. The diffusion properties of IP in CDNS can be modulated by suitable polymer synthesis; this finding opens the possibility to design suitable systems for drug delivery with predictable and desired drug release properties.

Fan Blade Development

DTIC Science & Technology

1982-09-01

Reviewed by: IP. A. Saigh, P.E. L. B. Hoyl , Ph.D. Director, Government Programs Manageri Mechanical Engineering Department I I GARD, INC. r I...D.C. 20301 Mr. C. Wilton 2 Scientific Service Inc. 517 East Bayshore Drive Redwood City, California 94060 Mr. Fred Sauer 1 Physics International

Enhanced Production of Polysaccharide Through the Overexpression of Homologous Uridine Diphosphate Glucose Pyrophosphorylase Gene in a Submerged Culture of Lingzhi or Reishi Medicinal Mushroom, Ganoderma lucidum (Higher Basidiomycetes).

PubMed

Ji, Sen-Lin; Liu, Rui; Ren, Meng-Fei; Li, Huan-Jun; Xu, Jun-Wei

2015-01-01

This study aimed to improve polysaccharide production by engineering the biosynthetic pathway in Ganoderma lucidum through the overexpression of the homologous UDP glucose pyrophosphorylase (UGP) gene. The effects of UGP gene overexpression on intracellular polysaccharide (IPS) content, extracellular polysaccharide (EPS) production, and transcription levels of 3 genes encoding the enzymes involved in polysaccharide biosynthesis, including phosphoglucomutase (PGM), UGP, and α-1,3-glucan synthase (GLS), were investigated. The maximum IPS content and EPS production in G. lucidum overexpressing the UGP gene were 24.32 mg/100 mg dry weight and 1.66 g/L, respectively, which were higher by 42% and 36% than those of the wild-type strain. The transcription levels of PGM, UGP, and GLS were up-regulated by 1.6, 2.6, and 2.4-fold, respectively, in the engineered strain, suggesting that increased polysaccharide biosynthesis may result from a higher expression of those genes.

Mission to Mars using integrated propulsion concepts: considerations, opportunities, and strategies.

PubMed

Accettura, Antonio G; Bruno, Claudio; Casotto, Stefano; Marzari, Francesco

2004-04-01

The aim of this paper is to evaluate the feasibility of a mission to Mars using the Integrated Propulsion Systems (IPS) which means to couple Nuclear-MPD-ISPU propulsion systems. In particular both mission analysis and propulsion aspects are analyzed together with technological aspects. Identifying possible mission scenarios will lead to the study of possible strategies for Mars Exploration and also of methods for reducing cost. As regard to IPS, the coupling between Nuclear Propulsion (Rubbia's engine) and Superconductive MPD propulsion is considered for the Earth-Mars trajectories: major emphasis is given to the advantages of such a system. The In Situ Resource Utilization (ISRU) concerns on-Mars operations; In Situ Propellant Utilization (ISPU) is foreseen particularly for LOX-CH4 engines for Mars Ascent Vehicles and this possibility is analyzed from a technological point of view. Tether Systems are also considered during interplanetary trajectories and as space elevators on Mars orbit. Finally strategic considerations associated to this mission are considered also. c2003 Elsevier Ltd. All rights reserved.

Detailed characterization of the LLNL imaging proton spectrometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rasmus, A. M., E-mail: rasmus@lanl.gov, E-mail: arasmus@umich.edu; University of Michigan, Ann Arbor, Michigan 48109; Hazi, A. U.

2016-11-15

Ultra-intense short pulse lasers incident on solid targets (e.g., thin Au foils) produce well collimated, broad-spectrum proton beams. These proton beams can be used to characterize magnetic fields, electric fields, and density gradients in high energy-density systems. The LLNL-Imaging Proton Spectrometer (L-IPS) was designed and built [H. Chen et al., Rev. Sci. Instrum. 81, 10D314 (2010)] for use with such laser produced proton beams. The L-IPS has an energy range of 50 keV-40 MeV with a resolving power (E/dE) of about 275 at 1 MeV and 21 at 20 MeV, as well as a single spatial imaging axis. In ordermore » to better characterize the dispersion and imaging capability of this diagnostic, a 3D finite element analysis solver is used to calculate the magnetic field of the L-IPS. Particle trajectories are then obtained via numerical integration to determine the dispersion relation of the L-IPS in both energy and angular space.« less

An interactive environment for agile analysis and visualization of ChIP-sequencing data.

PubMed

Lerdrup, Mads; Johansen, Jens Vilstrup; Agrawal-Singh, Shuchi; Hansen, Klaus

2016-04-01

To empower experimentalists with a means for fast and comprehensive chromatin immunoprecipitation sequencing (ChIP-seq) data analyses, we introduce an integrated computational environment, EaSeq. The software combines the exploratory power of genome browsers with an extensive set of interactive and user-friendly tools for genome-wide abstraction and visualization. It enables experimentalists to easily extract information and generate hypotheses from their own data and public genome-wide datasets. For demonstration purposes, we performed meta-analyses of public Polycomb ChIP-seq data and established a new screening approach to analyze more than 900 datasets from mouse embryonic stem cells for factors potentially associated with Polycomb recruitment. EaSeq, which is freely available and works on a standard personal computer, can substantially increase the throughput of many analysis workflows, facilitate transparency and reproducibility by automatically documenting and organizing analyses, and enable a broader group of scientists to gain insights from ChIP-seq data.

Two Sides of the Same Coin: ERP and Wavelet Analyses of Visual Potentials Evoked and Induced by Task-Relevant Faces.

PubMed

Van der Lubbe, Rob H J; Szumska, Izabela; Fajkowska, Małgorzata

2016-01-01

New analysis techniques of the electroencephalogram (EEG) such as wavelet analysis open the possibility to address questions that may largely improve our understanding of the EEG and clarify its relation with related potentials (ER Ps). Three issues were addressed. 1) To what extent can early ERERP components be described as transient evoked oscillations in specific frequency bands? 2) Total EEG power (TP) after a stimulus consists of pre-stimulus baseline power (BP), evoked power (EP), and induced power (IP), but what are their respective contributions? 3) The Phase Reset model proposes that BP predicts EP, while the evoked model holds that BP is unrelated to EP; which model is the most valid one? EEG results on NoGo trials for 123 individuals that took part in an experiment with emotional facial expressions were examined by computing ERPs and by performing wavelet analyses on the raw EEG and on ER Ps. After performing several multiple regression analyses, we obtained the following answers. First, the P1, N1, and P2 components can by and large be described as transient oscillations in the α and θ bands. Secondly, it appears possible to estimate the separate contributions of EP, BP, and IP to TP, and importantly, the contribution of IP is mostly larger than that of EP. Finally, no strong support was obtained for either the Phase Reset or the Evoked model. Recent models are discussed that may better explain the relation between raw EEG and ERPs.

Two Sides of the Same Coin: ERP and Wavelet Analyses of Visual Potentials Evoked and Induced by Task-Relevant Faces

PubMed Central

Van der Lubbe, Rob H. J.; Szumska, Izabela; Fajkowska, Małgorzata

2016-01-01

New analysis techniques of the electroencephalogram (EEG) such as wavelet analysis open the possibility to address questions that may largely improve our understanding of the EEG and clarify its relation with related potentials (ER Ps). Three issues were addressed. 1) To what extent can early ERERP components be described as transient evoked oscillations in specific frequency bands? 2) Total EEG power (TP) after a stimulus consists of pre-stimulus baseline power (BP), evoked power (EP), and induced power (IP), but what are their respective contributions? 3) The Phase Reset model proposes that BP predicts EP, while the evoked model holds that BP is unrelated to EP; which model is the most valid one? EEG results on NoGo trials for 123 individuals that took part in an experiment with emotional facial expressions were examined by computing ERPs and by performing wavelet analyses on the raw EEG and on ER Ps. After performing several multiple regression analyses, we obtained the following answers. First, the P1, N1, and P2 components can by and large be described as transient oscillations in the α and θ bands. Secondly, it appears possible to estimate the separate contributions of EP, BP, and IP to TP, and importantly, the contribution of IP is mostly larger than that of EP. Finally, no strong support was obtained for either the Phase Reset or the Evoked model. Recent models are discussed that may better explain the relation between raw EEG and ERPs. PMID:28154612

Simulation and experiment for oxygen-enriched combustion engine using liquid oxygen to solidify CO2

NASA Astrophysics Data System (ADS)

Liu, Yongfeng; Jia, Xiaoshe; Pei, Pucheng; Lu, Yong; Yi, Li; Shi, Yan

2016-01-01

For capturing and recycling of CO2 in the internal combustion engine, Rankle cycle engine can reduce the exhaust pollutants effectively under the condition of ensuring the engine thermal efficiency by using the techniques of spraying water in the cylinder and optimizing the ignition advance angle. However, due to the water spray nozzle need to be installed on the cylinder, which increases the cylinder head design difficulty and makes the combustion conditions become more complicated. In this paper, a new method is presented to carry out the closing inlet and exhaust system for internal combustion engines. The proposed new method uses liquid oxygen to solidify part of cooled CO2 from exhaust system into dry ice and the liquid oxygen turns into gas oxygen which is sent to inlet system. The other part of CO2 is sent to inlet system and mixed with oxygen, which can reduce the oxygen-enriched combustion detonation tendency and make combustion stable. Computing grid of the IP52FMI single-cylinder four-stroke gasoline-engine is established according to the actual shape of the combustion chamber using KIVA-3V program. The effects of exhaust gas recirculation (EGR) rate are analyzed on the temperatures, the pressures and the instantaneous heat release rates when the EGR rate is more than 8%. The possibility of enclosing intake and exhaust system for engine is verified. The carbon dioxide trapping device is designed and the IP52FMI engine is transformed and the CO2 capture experiment is carried out. The experimental results show that when the EGR rate is 36% for the optimum EGR rate. When the liquid oxygen of 35.80-437.40 g is imported into the device and last 1-20 min, respectively, 21.50-701.30 g dry ice is obtained. This research proposes a new design method which can capture CO2 for vehicular internal combustion engine.

Maximizing MST's inductive capability with a Bp programmable power supply

NASA Astrophysics Data System (ADS)

Chapman, B. E.; Holly, D. J.; Jacobson, C. M.; McCollam, K. J.; Morin, J. C.; Sarff, J. S.; Squitieri, A.

2016-10-01

A major goal of the MST program is the advancement of inductive control for the development of both the RFP's fusion potential and, synergistically, the predictive capability of fusion science. This entails programmable power supplies (PPS's) for the Bt and Bp circuits. A Bt PPS is already in place, allowing advanced RFP operation and the production of tokamak plasmas, and a Bp PPS prototype is under construction. To explore some of the new capabilities to be provided by the Bp PPS, the existing Bt PPS has been temporarily connected to the Bp circuit. One key result is new-found access to very low Ip (20 kA) and very low Lundquist number, S (104). At this low S, simulation of RFP plasmas with the MHD code NIMROD is readily achievable, and work toward validation of extended MHD models using NIMROD is underway with direct comparisons to these MST plasmas. The full Bp PPS will also provide higher Ip and S than presently possible, allowing MST to produce plasmas with S spanning as much as five orders of magnitude, a dramatic extension of MST's capability. In these initial tests, the PPS has also increased five-fold MST's Ip flattop duration, to about 100 ms. This, coupled with the recently demonstrated PPS ability to drive large-amplitude sinusoidal oscillations in Ip, will allow tests of extended-duration oscillating field current drive, the goal of which is ac sustainment of a quasi-dc plasma current. Work supported by US DOE.

Combining genomic and proteomic approaches for epigenetics research

PubMed Central

Han, Yumiao; Garcia, Benjamin A

2014-01-01

Epigenetics is the study of changes in gene expression or cellular phenotype that do not change the DNA sequence. In this review, current methods, both genomic and proteomic, associated with epigenetics research are discussed. Among them, chromatin immunoprecipitation (ChIP) followed by sequencing and other ChIP-based techniques are powerful techniques for genome-wide profiling of DNA-binding proteins, histone post-translational modifications or nucleosome positions. However, mass spectrometry-based proteomics is increasingly being used in functional biological studies and has proved to be an indispensable tool to characterize histone modifications, as well as DNA–protein and protein–protein interactions. With the development of genomic and proteomic approaches, combination of ChIP and mass spectrometry has the potential to expand our knowledge of epigenetics research to a higher level. PMID:23895656

The role of the human papillomavirus in the pathogenesis of Schneiderian inverted papillomas: an analytic overview of the evidence.

PubMed

Lawson, William; Schlecht, Nicolas F; Brandwein-Gensler, Margaret

2008-06-01

Evidence of an etiological role for human papillomavirus (HPV) in Schneiderian inverted papillomas IP arose in the late 1980's; yet almost three decades later, the association between HPV and IP has yet to be universally accepted. This is probably due to the disparate HPV detection rates in IP reported in the literature. We analyzed the weight of published data in order to address the following questions: why do the HPV detection rates in IP vary so greatly? What is the relationship between low-risk (LR) and high-risk (HR) HPV types and HPV detection rates in IP? Is there a relationship between the presence and type of HPV in IP and recurrence and malignant progression? A search using the Pubmed search engine was performed to identify studies published in English from 01/87 through 12/06 using the MeSH terms ''HPV'' and ''Inverted", "Exophytic", "Oncocytic Schneiderian" or "Fungiform papilloma''. Data was abstracted from publications including histology, HPV target, HPV type, method of detection, etc. HPV results were stratified by histology and other variables. Tests for heterogeneity (between-study variability) were conducted, and weighted prevalence (WP) estimates and 95% confidence intervals (CI) were calculated using a random-effects inverse-variance model stratified on study. The association between HPV IP recurrence was estimated by random-effects inverse-variance weighted odds ratio (OR). Weighted estimates revealed similar detection rates across detection methods, 26.8% (95%CI 16.4-37.2%) by ISH, 25.2% (95%CI 14.7-35.6%) by consensus PCR, and 23.6% (95%CI 12.2-35.0%) by type-specific PCR. A preponderance of HPV 6/11 is found in IP as compared to HPV 16/18; the overall unadjusted ratio of LR to high-risk HR HPV types is 2.8:1 The HPV detection rates significantly increase (Wald t-test P < 0.02) in IPs with high-grade dysplasia (WP 55.8%, 95%CI 30.5-81.0%) and carcinoma (WP 55.1%, 95%CI 37.0-73.2%) as compared to IPs with no dysplasia or mild dysplasia (WP 22.3%, 95%CI 15.9-28.6%). Furthermore, the preponderance of LR HPV in benign IP (ratio LR/HR = 4.8:1) shifts in dysplastic and malignant IP. The LR/HR ratio is 1.1:1 for IPs with high-grade dysplasias, this ratio is inverted to favor HR HPV (1:2.4) for malignant IP. Recurrences developed in 44 of 236 patients; HPV was detected in 27 of 44 IPs (WP 57.9%, 95%CI 31.6-84.2%) that developed recurrences and in 24 of 192 IPs (WP 9.7%, 95%CI 4.4-15.0%) that did not develop recurrence. The presence of HPV was significantly associated with the likelihood of developing recurrence (weighted OR of 10.2, 95%CI 3.2-32.8). We hypothesize that LR HPV may induce IP formation, and then are lost as infected cells are shed, as a "hit and run" phenomenon. HPV detection rates increase in dysplastic IP and SCC-ex-IP with increasing ratio of HR to LR HPV types, compared to nondysplastic IP. We believe that one explanation for the variation in HPV detection rates between different studies may be the actual histologic composition of the cohort. That is, if one series contains a higher frequency of dysplastic and malignant IP, it may have a higher detection rate than another series which contains only nondysplastic IP. We hypothesize that the higher rates of HPV detection in dysplastic and malignant IP may be related to HPV integration. The implication of this is that HPV sub-type testing may identify patients at risk for recurrence, or progression to dysplasia and malignancy, and thus may impact surveillance protocols.

Naval Open Architecture Machinery Control Systems for Next Generation Integrated Power Systems

DTIC Science & Technology

2012-05-01

PORTABLE) OS / RTOS ADAPTATION MIDDLEWARE (FOR OS PORTABILITY) MACHINERY CONTROLLER FRAMEWORK MACHINERY CONTROL SYSTEM SERVICES POWER CONTROL SYSTEM...SERVICES SHIP SYSTEM SERVICES TTY 0 TTY N … OPERATING SYSTEM ( OS / RTOS ) COMPUTER HARDWARE UDP IP TCP RAW DEV 0 DEV N … POWER MANAGEMENT CONTROLLER...operating systems (DOS, Windows, Linux, OS /2, QNX, SCO Unix ...) COMPUTERS: ISA compatible motherboards, workstations and portables (Compaq, Dell

Third order intermodulation distortion in HTS Josephson Junction downconverter at 12GHz

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suzuki, Katsumi; Hayashi, Kunihiko; Fujimoto, Manabu

1994-12-31

Here the authors first report on the microwave characteristics of the third order intermodulation distortion(IMD3) in High-Tc Superconductor (HTS) Josephson Junction (JJ) Downconverter at 12GHz. They have successfully developed high quality nonlinear YBCO microbridge Josephson junctions for such an active MMIC as a mixer with RF, LO, IF and bias filters, which have been fabricated on (100) MgO substrates with 20mm x 20mm x 0.5mm dimensions. The minimum conversion loss of the JJ mixer is 11 dB at very small local microwave input power LO= {minus}20dBm which is two order less than Schottky diode mixer. Consequently, this small optimum LOmore » power gives the small RF input power at which the output IF power of the YBCO mixer saturates. Two-tone third-order intercept point(IP3) performance is a significantly important figure of merit typically used to define linearity of devices and circuits. The RF input power = {minus}15dBm at the IP3 point is obtained for the YBCO mixer at 15K and LO = 10.935GHz with {minus}22dBm. The have successfully measured the dependence of IMD3 on temperature, bias current and LO power.« less

cChIP-seq: a robust small-scale method for investigation of histone modifications.

PubMed

Valensisi, Cristina; Liao, Jo Ling; Andrus, Colin; Battle, Stephanie L; Hawkins, R David

2015-12-21

ChIP-seq is highly utilized for mapping histone modifications that are informative about gene regulation and genome annotations. For example, applying ChIP-seq to histone modifications such as H3K4me1 has facilitated generating epigenomic maps of putative enhancers. This powerful technology, however, is limited in its application by the large number of cells required. ChIP-seq involves extensive manipulation of sample material and multiple reactions with limited quality control at each step, therefore, scaling down the number of cells required has proven challenging. Recently, several methods have been proposed to overcome this limit but most of these methods require extensive optimization to tailor the protocol to the specific antibody used or number of cells being profiled. Here we describe a robust, yet facile method, which we named carrier ChIP-seq (cChIP-seq), for use on limited cell amounts. cChIP-seq employs a DNA-free histone carrier in order to maintain the working ChIP reaction scale, removing the need to tailor reactions to specific amounts of cells or histone modifications to be assayed. We have applied our method to three different histone modifications, H3K4me3, H3K4me1 and H3K27me3 in the K562 cell line, and H3K4me1 in H1 hESCs. We successfully obtained epigenomic maps for these histone modifications starting with as few as 10,000 cells. We compared cChIP-seq data to data generated as part of the ENCODE project. ENCODE data are the reference standard in the field and have been generated starting from tens of million of cells. Our results show that cChIP-seq successfully recapitulates bulk data. Furthermore, we showed that the differences observed between small-scale ChIP-seq data and ENCODE data are largely to be due to lab-to-lab variability rather than operating on a reduced scale. Data generated using cChIP-seq are equivalent to reference epigenomic maps from three orders of magnitude more cells. Our method offers a robust and straightforward approach to scale down ChIP-seq to as low as 10,000 cells. The underlying principle of our strategy makes it suitable for being applied to a vast range of chromatin modifications without requiring expensive optimization. Furthermore, our strategy of a DNA-free carrier can be adapted to most ChIP-seq protocols.

PAPST, a User Friendly and Powerful Java Platform for ChIP-Seq Peak Co-Localization Analysis and Beyond.

PubMed

Bible, Paul W; Kanno, Yuka; Wei, Lai; Brooks, Stephen R; O'Shea, John J; Morasso, Maria I; Loganantharaj, Rasiah; Sun, Hong-Wei

2015-01-01

Comparative co-localization analysis of transcription factors (TFs) and epigenetic marks (EMs) in specific biological contexts is one of the most critical areas of ChIP-Seq data analysis beyond peak calling. Yet there is a significant lack of user-friendly and powerful tools geared towards co-localization analysis based exploratory research. Most tools currently used for co-localization analysis are command line only and require extensive installation procedures and Linux expertise. Online tools partially address the usability issues of command line tools, but slow response times and few customization features make them unsuitable for rapid data-driven interactive exploratory research. We have developed PAPST: Peak Assignment and Profile Search Tool, a user-friendly yet powerful platform with a unique design, which integrates both gene-centric and peak-centric co-localization analysis into a single package. Most of PAPST's functions can be completed in less than five seconds, allowing quick cycles of data-driven hypothesis generation and testing. With PAPST, a researcher with or without computational expertise can perform sophisticated co-localization pattern analysis of multiple TFs and EMs, either against all known genes or a set of genomic regions obtained from public repositories or prior analysis. PAPST is a versatile, efficient, and customizable tool for genome-wide data-driven exploratory research. Creatively used, PAPST can be quickly applied to any genomic data analysis that involves a comparison of two or more sets of genomic coordinate intervals, making it a powerful tool for a wide range of exploratory genomic research. We first present PAPST's general purpose features then apply it to several public ChIP-Seq data sets to demonstrate its rapid execution and potential for cutting-edge research with a case study in enhancer analysis. To our knowledge, PAPST is the first software of its kind to provide efficient and sophisticated post peak-calling ChIP-Seq data analysis as an easy-to-use interactive application. PAPST is available at https://github.com/paulbible/papst and is a public domain work.

PAPST, a User Friendly and Powerful Java Platform for ChIP-Seq Peak Co-Localization Analysis and Beyond

PubMed Central

Bible, Paul W.; Kanno, Yuka; Wei, Lai; Brooks, Stephen R.; O’Shea, John J.; Morasso, Maria I.; Loganantharaj, Rasiah; Sun, Hong-Wei

2015-01-01

Comparative co-localization analysis of transcription factors (TFs) and epigenetic marks (EMs) in specific biological contexts is one of the most critical areas of ChIP-Seq data analysis beyond peak calling. Yet there is a significant lack of user-friendly and powerful tools geared towards co-localization analysis based exploratory research. Most tools currently used for co-localization analysis are command line only and require extensive installation procedures and Linux expertise. Online tools partially address the usability issues of command line tools, but slow response times and few customization features make them unsuitable for rapid data-driven interactive exploratory research. We have developed PAPST: Peak Assignment and Profile Search Tool, a user-friendly yet powerful platform with a unique design, which integrates both gene-centric and peak-centric co-localization analysis into a single package. Most of PAPST’s functions can be completed in less than five seconds, allowing quick cycles of data-driven hypothesis generation and testing. With PAPST, a researcher with or without computational expertise can perform sophisticated co-localization pattern analysis of multiple TFs and EMs, either against all known genes or a set of genomic regions obtained from public repositories or prior analysis. PAPST is a versatile, efficient, and customizable tool for genome-wide data-driven exploratory research. Creatively used, PAPST can be quickly applied to any genomic data analysis that involves a comparison of two or more sets of genomic coordinate intervals, making it a powerful tool for a wide range of exploratory genomic research. We first present PAPST’s general purpose features then apply it to several public ChIP-Seq data sets to demonstrate its rapid execution and potential for cutting-edge research with a case study in enhancer analysis. To our knowledge, PAPST is the first software of its kind to provide efficient and sophisticated post peak-calling ChIP-Seq data analysis as an easy-to-use interactive application. PAPST is available at https://github.com/paulbible/papst and is a public domain work. PMID:25970601

40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Maximum engine power, displacement... Maximum engine power, displacement, power density, and maximum in-use engine speed. This section describes how to determine the maximum engine power, displacement, and power density of an engine for the...

40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Maximum engine power, displacement... Maximum engine power, displacement, power density, and maximum in-use engine speed. This section describes how to determine the maximum engine power, displacement, and power density of an engine for the...

Endopolysaccharides from Ganoderma resinaceum, Phlebia rufa, and Trametes versicolor affect differently the proliferation rate of HepG2 cells.

PubMed

Silva, Amélia M; Miranda, Andreia; Fernandes, Elisabete; Santos, Susana; Fraga, Irene; Santos, Dario L; Dias, Albino A; Bezerra, Rui M

2013-03-01

Fungi have been used for medicinal purposes for long time by Asian countries, being a putative source of powerful new phytopharmaceuticals such as polysaccharides. The aim of this study was to extract endopolysaccharides (IPS) from Ganoderma resinaceum, Phlebia rufa, and Trametes versicolor, grown under submerged culture, to compare crude IPS production, total carbohydrate, and protein yield, and to study the effect of these IPS on HepG2 cells proliferation rate. Total biomass produced by G. resinaceum, P. rufa, and T. versicolor was (in gram per liter) 3.32 ± 0.80, 5.42 ± 0.58, and 4.2 ± 1.29 and the IPS yield (as the biomass percent) was 9.9 ± 0.05, 29.0 ± 6.3, and 9.1 ± 3.1 %, respectively. Characterization of IPS has shown different proportion between total sugar and protein being, on average 6.04, 10.74, and 22.62, for G. resinaceum, T. versicolor, and P. rufa, respectively. The IPS effect, at 50, 100, and 200 μg mL(-1) on HepG2 cell growth and viability was negligible for G. resinaceum and P. rufa but, in the case of T. versicolor, 200 μg mL(-1) of IPS evoked 40 % reduction on cell growth. The results suggest that the intracellular polysaccharides from T. versicolor are a potential source for bioactive molecules with anti-proliferative properties.

ChiLin: a comprehensive ChIP-seq and DNase-seq quality control and analysis pipeline.

PubMed

Qin, Qian; Mei, Shenglin; Wu, Qiu; Sun, Hanfei; Li, Lewyn; Taing, Len; Chen, Sujun; Li, Fugen; Liu, Tao; Zang, Chongzhi; Xu, Han; Chen, Yiwen; Meyer, Clifford A; Zhang, Yong; Brown, Myles; Long, Henry W; Liu, X Shirley

2016-10-03

Transcription factor binding, histone modification, and chromatin accessibility studies are important approaches to understanding the biology of gene regulation. ChIP-seq and DNase-seq have become the standard techniques for studying protein-DNA interactions and chromatin accessibility respectively, and comprehensive quality control (QC) and analysis tools are critical to extracting the most value from these assay types. Although many analysis and QC tools have been reported, few combine ChIP-seq and DNase-seq data analysis and quality control in a unified framework with a comprehensive and unbiased reference of data quality metrics. ChiLin is a computational pipeline that automates the quality control and data analyses of ChIP-seq and DNase-seq data. It is developed using a flexible and modular software framework that can be easily extended and modified. ChiLin is ideal for batch processing of many datasets and is well suited for large collaborative projects involving ChIP-seq and DNase-seq from different designs. ChiLin generates comprehensive quality control reports that include comparisons with historical data derived from over 23,677 public ChIP-seq and DNase-seq samples (11,265 datasets) from eight literature-based classified categories. To the best of our knowledge, this atlas represents the most comprehensive ChIP-seq and DNase-seq related quality metric resource currently available. These historical metrics provide useful heuristic quality references for experiment across all commonly used assay types. Using representative datasets, we demonstrate the versatility of the pipeline by applying it to different assay types of ChIP-seq data. The pipeline software is available open source at https://github.com/cfce/chilin . ChiLin is a scalable and powerful tool to process large batches of ChIP-seq and DNase-seq datasets. The analysis output and quality metrics have been structured into user-friendly directories and reports. We have successfully compiled 23,677 profiles into a comprehensive quality atlas with fine classification for users.

Electronic Reference Library: Silverplatter's Database Networking Solution.

ERIC Educational Resources Information Center

Millea, Megan

Silverplatter's Electronic Reference Library (ERL) provides wide area network access to its databases using TCP/IP communications and client-server architecture. ERL has two main components: The ERL clients (retrieval interface) and the ERL server (search engines). ERL clients provide patrons with seamless access to multiple databases on multiple…

Influence of Training Models at 3,900-m Altitude on the Physiological Response and Performance of a Professional Wheelchair Athlete: A Case Study.

PubMed

Sanz-Quinto, Santiago; López-Grueso, Raúl; Brizuela, Gabriel; Flatt, Andrew A; Moya-Ramón, Manuel

2018-06-20

Sanz-Quinto, S, López-Grueso, R, Brizuela, G, Flatt, AA, and Moya-Ramón, M. Influence of training models at 3,900-m altitude on the physiological response and performance of a professional wheelchair athlete: A case study. J Strength Cond Res XX(X): 000-000, 2018-This case study compared the effects of two training camps using flexible planning (FP) vs. inflexible planning (IP) at 3,860-m altitude on physiological and performance responses of an elite marathon wheelchair athlete with Charcot-Marie-Tooth disease (CMT). During IP, the athlete completed preplanned training sessions. During FP, training was adjusted based on vagally mediated heart rate variability (HRV) with specific sessions being performed when a reference HRV value was attained. The camp phases were baseline in normoxia (BN), baseline in hypoxia (BH), specific training weeks 1-4 (W1, W2, W3, W4), and Post-camp (Post). Outcome measures included the root mean square of successive R-R interval differences (rMSSD), resting heart rate (HRrest), oxygen saturation (SO2), diastolic blood pressure and systolic blood pressure, power output and a 3,000-m test. A greater impairment of normalized rMSSD (BN) was shown in IP during BH (57.30 ± 2.38% vs. 72.94 ± 11.59%, p = 0.004), W2 (63.99 ± 10.32% vs. 81.65 ± 8.87%, p = 0.005), and W4 (46.11 ± 8.61% vs. 59.35 ± 6.81%, p = 0.008). At Post, only in FP was rMSSD restored (104.47 ± 35.80%). Relative changes were shown in power output (+3 W in IP vs. +6 W in FP) and 3,000-m test (-7s in IP vs. -16s in FP). This case study demonstrated that FP resulted in less suppression and faster restoration of rMSSD and more positive changes in performance than IP in an elite wheelchair marathoner with CMT.

An Architecture for Coexistence with Multiple Users in Frequency Hopping Cognitive Radio Networks

DTIC Science & Technology

2013-03-01

the base WARP system, a custom IP core written in VHDL , and the Virtex IV’s embedded PowerPC core with C code to implement the radio and hopset...shown in Appendix C as Figure C.2. All VHDL code necessary to implement this IP core is included in Appendix G. 69 Figure 3.19: FPGA bus structure...subsystem functionality. A total of 1,430 lines of VHDL code were implemented for this research. 1 library ieee; 2 use ieee.std logic 1164.all; 3 use

Improving Service Management in the Internet of Things

PubMed Central

Sammarco, Chiara; Iera, Antonio

2012-01-01

In the Internet of Things (IoT) research arena, many efforts are devoted to adapt the existing IP standards to emerging IoT nodes. This is the direction followed by three Internet Engineering Task Force (IETF) Working Groups, which paved the way for research on IP-based constrained networks. Through a simplification of the whole TCP/IP stack, resource constrained nodes become direct interlocutors of application level entities in every point of the network. In this paper we analyze some side effects of this solution, when in the presence of large amounts of data to transmit. In particular, we conduct a performance analysis of the Constrained Application Protocol (CoAP), a widely accepted web transfer protocol for the Internet of Things, and propose a service management enhancement that improves the exploitation of the network and node resources. This is specifically thought for constrained nodes in the abovementioned conditions and proves to be able to significantly improve the node energetic performance when in the presence of large resource representations (hence, large data transmissions).

Harnessing the power of disgust: a randomized trial to reduce high-calorie food appeal through implicit priming.

PubMed

Legget, Kristina T; Cornier, Marc-Andre; Rojas, Donald C; Lawful, Benjamin; Tregellas, Jason R

2015-08-01

In our increasingly obesogenic environment, in which high-calorie convenience foods are readily available, food choices can drastically affect weight and overall health. Learned food preferences, which are developed through repeated pairings with positively and negatively valenced stimuli, can contribute to obesity susceptibility if positive attitudes toward high-calorie foods are developed. Thus, the modification of automatic associations with food may be a viable strategy to promote healthier eating behaviors. In this study, we investigated the ability of an implicit priming (IP) intervention to alter responses to visual food cues by using an evaluative conditioning approach. The main objective was to implicitly (i.e., below conscious perception) associate disgust with high-calorie foods with the aim of reducing liking of these foods. Participants were randomly assigned to active or control IP. In active IP (n = 22), high-calorie food images were implicitly primed with negatively valenced images, and low-calorie food images were implicitly primed with positively valenced images. In control IP (n = 20), all food images were primed with neutral images of fixation crosses. Food images were rated on the desire to eat immediately before and after IP. A significant main effect of calorie (high compared with low; P < 0.001) and a significant calorie-by-group (active compared with control) interaction (P = 0.025) were observed. Post hoc tests identified a significantly greater high-calorie rating decline after active IP than after control IP (P = 0.036). Furthermore, there was significantly greater change in high-calorie ratings than in low-calorie ratings in the active group (P = 0.001). Active IP effects extended to high-calorie foods not specifically included in the intervention, which suggested an effect generalization. Moreover, a greater change in high-calorie ratings than in low-calorie ratings persisted 3-5 d after active IP (P < 0.007), which suggested lasting effects. This study provides initial evidence that IP can be used to alter high-calorie food preferences, which could promote healthier eating habits. © 2015 American Society for Nutrition.

Anomalous diffusion of Ibuprofen in cyclodextrin nanosponge hydrogels: an HRMAS NMR study

PubMed Central

Ferro, Monica; Punta, Carlo; Melone, Lucio; Panzeri, Walter; Rossi, Barbara; Trotta, Francesco

2014-01-01

Summary Ibuprofen sodium salt (IP) was encapsulated in cyclodextrin nanosponges (CDNS) obtained by cross-linking of β-cyclodextrin with ethylenediaminetetraacetic acid dianhydride (EDTAn) in two different preparations: CDNSEDTA 1:4 and 1:8, where the 1:n notation indicates the CD to EDTAn molar ratio. The entrapment of IP was achieved by swelling the two polymers with a 0.27 M solution of IP in D2O, leading to colourless, homogeneous hydrogels loaded with IP. The molecular environment and the transport properties of IP in the hydrogels were studied by high resolution magic angle spinning (HRMAS) NMR spectroscopy. The mean square displacement (MSD) of IP in the gels was obtained by a pulsed field gradient spin echo (PGSE) NMR pulse sequence at different observation times t d. The MSD is proportional to the observation time elevated to a scaling factor α. The α values define the normal Gaussian random motion (α = 1), or the anomalous diffusion (α < 1, subdiffusion, α > 1 superdiffusion). The experimental data here reported point out that IP undergoes subdiffusive regime in CDNSEDTA 1:4, while a slightly superdiffusive behaviour is observed in CDNSEDTA 1:8. The transition between the two dynamic regimes is triggered by the polymer structure. CDNSEDTA 1:4 is characterized by a nanoporous structure able to induce confinement effects on IP, thus causing subdiffusive random motion. CDNSEDTA 1:8 is characterized not only by nanopores, but also by dangling EDTA groups ending with ionized COO− groups. The negative potential provided by such groups to the polymer backbone is responsible for the acceleration effects on the IP anion thus leading to the superdiffusive behaviour observed. These results point out that HRMAS NMR spectroscopy is a powerful direct method for the assessment of the transport properties of a drug encapsulated in polymeric scaffolds. The diffusion properties of IP in CDNS can be modulated by suitable polymer synthesis; this finding opens the possibility to design suitable systems for drug delivery with predictable and desired drug release properties. PMID:25550735

Activation of D2 autoreceptors alters cocaine-induced locomotion and slows down local field oscillations in the rat ventral tegmental area.

PubMed

Koulchitsky, Stanislav; Delairesse, Charlotte; Beeken, Thom; Monteforte, Alexandre; Dethier, Julie; Quertemont, Etienne; Findeisen, Rolf; Bullinger, Eric; Seutin, Vincent

2016-09-01

Psychoactive substances affecting the dopaminergic system induce locomotor activation and, in high doses, stereotypies. Network mechanisms underlying the shift from an active goal-directed behavior to a "seemingly purposeless" stereotypic locomotion remain unclear. In the present study we sought to determine the relationships between the behavioral effects of dopaminergic drugs and their effects on local field potentials (LFPs), which were telemetrically recorded within the ventral tegmental area (VTA) of freely moving rats. We used the D2/D3 agonist quinpirole in a low, autoreceptor-selective (0.1 mg/kg, i.p.) and in a high (0.5 mg/kg, i.p.) dose, and a moderate dose of cocaine (10 mg/kg, i.p.). In the control group, power spectrum analysis revealed a prominent peak of LFP power in the theta frequency range during active exploration. Cocaine alone stimulated locomotion, but had no significant effect on the peak of the LFP power. In contrast, co-administration of low dose quinpirole with cocaine markedly altered the pattern of locomotion, from goal-directed exploratory behavior to recurrent motion resembling locomotor stereotypy. This behavioral effect was accompanied by a shift of the dominant theta power toward a significantly lower (by ∼15%) frequency. High dose quinpirole also provoked an increased locomotor activity with signs of behavioral stereotypies, and also induced a shift of the dominant oscillation frequency toward the lower range. These results demonstrate a correlation between the LFP oscillation frequency within the VTA and a qualitative aspect of locomotor behavior, perhaps due to a variable level of coherence of this region with its input or output areas. Copyright © 2016 Elsevier Ltd. All rights reserved.

How do output growth-rate distributions look like? Some cross-country, time-series evidence

NASA Astrophysics Data System (ADS)

Fagiolo, G.; Napoletano, M.; Roventini, A.

2007-05-01

This paper investigates the statistical properties of within-country gross domestic product (GDP) and industrial production (IP) growth-rate distributions. Many empirical contributions have recently pointed out that cross-section growth rates of firms, industries and countries all follow Laplace distributions. In this work, we test whether also within-country, time-series GDP and IP growth rates can be approximated by tent-shaped distributions. We fit output growth rates with the exponential-power (Subbotin) family of densities, which includes as particular cases both Gaussian and Laplace distributions. We find that, for a large number of OECD (Organization for Economic Cooperation and Development) countries including the US, both GDP and IP growth rates are Laplace distributed. Moreover, we show that fat-tailed distributions robustly emerge even after controlling for outliers, autocorrelation and heteroscedasticity.

Can insoluble polysaccharide concentration in dental plaque, sugar exposure and cariogenic microorganisms predict early childhood caries? A follow-up study.

PubMed

Parisotto, T M; Stipp, R; Rodrigues, L K A; Mattos-Graner, R O; Costa, L S; Nobre-Dos-Santos, M

2015-08-01

Insoluble polysaccharide (IP) has been associated with caries prevalence in young children. However, the power of IP to predict ECC needs to be demonstrated. To assess the relationships between early childhood caries (ECC) and extracellular insoluble polysaccharides (IP) in dental plaque, sugar exposure and cariogenic microorganisms. Visible plaque on maxillary incisors was recorded, followed by caries diagnosis in 65 preschoolers (3-4 years) at baseline and after 1 year. Plaque was collected for mutans streptococci (MS), total microorganism (TM) and lactobacilli (LB) enumerations in selective media, as well as for IP analysis, which was later assessed by colorimetry. Sugar/sucrose exposure was assessed by a diet chart. Positive correlations were found among the prevalence of caries and MS, TM, LB, solid sucrose and visible dental plaque. Additionally, children with IP concentrations in dental plaque higher than 2.36 μg/mg (odds ratio-OR=6.8), with visible plaque on maxillary incisors (OR=4.3), harbouring LB (OR=13) and exposed to solid sugar more than twice/day (OR=5) showed higher risk of developing caries (p<0.05). Extracellular insoluble polysaccharides, solid sugar/sucrose, visible dental plaque and cariogenic microorganisms could predict caries development, partially explaining the ECC pattern. Copyright © 2015 Elsevier Ltd. All rights reserved.

Geothermal Exploration By Using Time Domain IP Method:Balikesir (Gure) And Canakkale (Geyikli) Cases From Turkey

NASA Astrophysics Data System (ADS)

Tezel, O.; Ozcep, F.

2017-12-01

Geothermal energy is heat derived from the earth. It is the thermal energy contained in the rock and fluid (that fills the fractures and pores within the rock) in the earth's crust. These resources are always at a temperature higher than 20°C. Geothermal energy requires no fuel, and is therefore virtually emission free and independent of fluctuations in fuel cost. Since a geothermal power plant doesn't rely on transient sources of energy, unlike, for example, wind turbines or solar panels, its capacity factor can be quite large. Induced polarization (IP) results at geothermal regions show prominent, extended low resistivity zones. Environmental-IP methods can assist in the assessment of the acid generating potential of waste rock and tailings from mine operations. Resistivity can be used to map contamination plumes. Resistivity and chargeability values were determined using the IP method on geothermal resources in Balikesir Güre (Turkey). In this study we found low resistance values and high chargeability values at the geothermal resource. Finally drilling and IP results were correlated to verify our findings. After the positive results of obtained data, a similar study was carried out in Geyikli Area (Canakkale) and a geothermal resource with 450C temperature of 5 lt/sec was explored at a depth of 970 m.

A novel statistical method for quantitative comparison of multiple ChIP-seq datasets.

PubMed

Chen, Li; Wang, Chi; Qin, Zhaohui S; Wu, Hao

2015-06-15

ChIP-seq is a powerful technology to measure the protein binding or histone modification strength in the whole genome scale. Although there are a number of methods available for single ChIP-seq data analysis (e.g. 'peak detection'), rigorous statistical method for quantitative comparison of multiple ChIP-seq datasets with the considerations of data from control experiment, signal to noise ratios, biological variations and multiple-factor experimental designs is under-developed. In this work, we develop a statistical method to perform quantitative comparison of multiple ChIP-seq datasets and detect genomic regions showing differential protein binding or histone modification. We first detect peaks from all datasets and then union them to form a single set of candidate regions. The read counts from IP experiment at the candidate regions are assumed to follow Poisson distribution. The underlying Poisson rates are modeled as an experiment-specific function of artifacts and biological signals. We then obtain the estimated biological signals and compare them through the hypothesis testing procedure in a linear model framework. Simulations and real data analyses demonstrate that the proposed method provides more accurate and robust results compared with existing ones. An R software package ChIPComp is freely available at http://web1.sph.emory.edu/users/hwu30/software/ChIPComp.html. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Objective comparison of 4 nonlongitudinal ultrasound modalities regarding efficiency and chatter.

PubMed

DeMill, David L; Zaugg, Brian E; Pettey, Jeff H; Jensen, Jason D; Jardine, Griffin J; Wong, Gilbert; Olson, Randall J

2012-06-01

To compare efficiency and chatter of Infiniti Ozil with and without Intelligent Phacoemulsification (IP) and the Signature Ellips with and without FX. John A. Moran Eye Center, University of Utah, Salt Lake City, Utah, USA. Experimental study. Brunescent 2.0 mm human lens cubes were created by an instrument devised for this study. Cubes were tested (10 per test) for time of particle removal (efficiency) and for the number of times the lens particle bounced off the tip (chatter) at 300 mm Hg and 550 mm Hg, 50% and 100% power, and 50% and 100% amplitudes (amplitude for Ozil only). Of the ultrasound settings, efficiency varied from a mean of 3.3 seconds ± 1.4 (SD) to 50.4 ± 11.7 seconds and chatter from 0.0 to 52.0 ± 16.7 bounces per run. The Ozil-IP was generally more efficient than the Ozil and the Ellips FX more efficient than the Ellips. At optimized values, the Ozil-IP and Ellips-FX were similar. In general, efficiency and chatter were better at 550 mm Hg and at 50% power. The amplitude effect was complex. Efficiency closely correlated with chatter (Pearson r(2) = .31, P<.0001). Objective comparison of phacoemulsification efficiency and chatter found that optimized Ozil-IP and Ellips-FX were similar in both parameters and in general, both performed better than preceding technology. The study parameters can significantly affect efficiency and chatter, which strongly correlate with each other. Copyright © 2012 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

Power Balance Modeling of Local Helicity Injection for Non-Solenoidal ST Startup

NASA Astrophysics Data System (ADS)

Weberski, J. D.; Barr, J. L.; Bongard, M. W.; Fonck, R. J.; Perry, J. M.; Reusch, J. A.

2017-10-01

A zero-dimensional power balance model for predicting Ip(t) for Local Helicity Injection (LHI) discharges has been used to interpret experimental results from recent experimental campaigns using high-field-side (HFS) helicity injection. This model quantifies LHI's effective drive (Veff) through helicity balance while enforcing the Taylor relaxation current limit and tracking inductive effects to determine Ip(t) . Recent analysis of HFS LHI discharges indicate LHI is the dominant source of drive and provides Veff up to 1.3 V while geometric effects and inductive drive provide < 0.1 V throughout much of the discharge. In contrast to previous analysis of low-field-side (LFS) LHI discharges, which were driven by Veff = 0.3 V and 2.0 V from geometric effects and inductive drive. A significant remaining uncertainty in the model is the resistive dissipation of LHI discharges. This requires greater understanding of LHI confinement scaling and impurity content, which are currently under investigation. However, the model and experimental Ip(t) exhibit good agreement for parameters consistent with previous experimental findings. Extrapolation of plasma parameters and shaping from recent experiments allow for the model to project the performance of LHI systems. These projections indicate Ip 0.3 MA can be accessed on Pegasus via HFS LHI through changes to injector geometry to provide more Veff. This regime can be accessed via a LFS system by increasing the Taylor relaxation current limit early in the discharge. Work supported by US DOE Grants DE-FG02-96ER54375 and DE-SC0006928.

40 CFR 1054.140 - What is my engine's maximum engine power and displacement?

Code of Federal Regulations, 2010 CFR

2010-07-01

... power and displacement? 1054.140 Section 1054.140 Protection of Environment ENVIRONMENTAL PROTECTION... engine power and displacement? This section describes how to quantify your engine's maximum engine power and displacement for the purposes of this part. (a) An engine configuration's maximum engine power is...

40 CFR 1054.140 - What is my engine's maximum engine power and displacement?

Code of Federal Regulations, 2011 CFR

2011-07-01

... power and displacement? 1054.140 Section 1054.140 Protection of Environment ENVIRONMENTAL PROTECTION... engine power and displacement? This section describes how to quantify your engine's maximum engine power and displacement for the purposes of this part. (a) An engine configuration's maximum engine power is...

40 CFR 1054.140 - What is my engine's maximum engine power and displacement?

Code of Federal Regulations, 2012 CFR

2012-07-01

... power and displacement? 1054.140 Section 1054.140 Protection of Environment ENVIRONMENTAL PROTECTION... engine power and displacement? This section describes how to quantify your engine's maximum engine power and displacement for the purposes of this part. (a) An engine configuration's maximum engine power is...

40 CFR 1054.140 - What is my engine's maximum engine power and displacement?

Code of Federal Regulations, 2014 CFR

2014-07-01

... power and displacement? 1054.140 Section 1054.140 Protection of Environment ENVIRONMENTAL PROTECTION... engine power and displacement? This section describes how to quantify your engine's maximum engine power and displacement for the purposes of this part. (a) An engine configuration's maximum engine power is...

40 CFR 1054.140 - What is my engine's maximum engine power and displacement?

Code of Federal Regulations, 2013 CFR

2013-07-01

... power and displacement? 1054.140 Section 1054.140 Protection of Environment ENVIRONMENTAL PROTECTION... engine power and displacement? This section describes how to quantify your engine's maximum engine power and displacement for the purposes of this part. (a) An engine configuration's maximum engine power is...

Collaborative Completion of Transcription Factor Binding Profiles via Local Sensitive Unified Embedding.

PubMed

Zhu, Lin; Guo, Wei-Li; Lu, Canyi; Huang, De-Shuang

2016-12-01

Although the newly available ChIP-seq data provides immense opportunities for comparative study of regulatory activities across different biological conditions, due to cost, time or sample material availability, it is not always possible for researchers to obtain binding profiles for every protein in every sample of interest, which considerably limits the power of integrative studies. Recently, by leveraging related information from measured data, Ernst et al. proposed ChromImpute for predicting additional ChIP-seq and other types of datasets, it is demonstrated that the imputed signal tracks accurately approximate the experimentally measured signals, and thereby could potentially enhance the power of integrative analysis. Despite the success of ChromImpute, in this paper, we reexamine its learning process, and show that its performance may degrade substantially and sometimes may even fail to output a prediction when the available data is scarce. This limitation could hurt its applicability to important predictive tasks, such as the imputation of TF binding data. To alleviate this problem, we propose a novel method called Local Sensitive Unified Embedding (LSUE) for imputing new ChIP-seq datasets. In LSUE, the ChIP-seq data compendium are fused together by mapping proteins, samples, and genomic positions simultaneously into the Euclidean space, thereby making their underling associations directly evaluable using simple calculations. In contrast to ChromImpute which mainly makes use of the local correlations between available datasets, LSUE can better estimate the overall data structure by formulating the representation learning of all involved entities as a single unified optimization problem. Meanwhile, a novel form of local sensitive low rank regularization is also proposed to further improve the performance of LSUE. Experimental evaluations on the ENCODE TF ChIP-seq data illustrate the performance of the proposed model. The code of LSUE is available at https://github.com/ekffar/LSUE.

Key technology research of HILS based on real-time operating system

NASA Astrophysics Data System (ADS)

Wang, Fankai; Lu, Huiming; Liu, Che

2018-03-01

In order to solve the problems that the long development cycle of traditional simulation and digital simulation doesn't have the characteristics of real time, this paper designed a HILS(Hardware In the Loop Simulation) system based on the real-time operating platform xPC. This system solved the communication problems between HMI and Simulink models through the MATLAB engine interface, and realized the functions of system setting, offline simulation, model compiling and downloading, etc. Using xPC application interface and integrating the TeeChart ActiveX chart component to realize the monitoring function of real-time target application; Each functional block in the system is encapsulated in the form of DLL, and the data interaction between modules was realized by MySQL database technology. When the HILS system runs, search the address of the online xPC target by means of the Ping command, to establish the Tcp/IP communication between the two machines. The technical effectiveness of the developed system is verified through the typical power station control system.

Doubling the spectrum of time-domain induced polarization by harmonic de-noising, drift correction, spike removal, tapered gating and data uncertainty estimation

NASA Astrophysics Data System (ADS)

Olsson, Per-Ivar; Fiandaca, Gianluca; Larsen, Jakob Juul; Dahlin, Torleif; Auken, Esben

2016-11-01

The extraction of spectral information in the inversion process of time-domain (TD) induced polarization (IP) data is changing the use of the TDIP method. Data interpretation is evolving from a qualitative description of the subsurface, able only to discriminate the presence of contrasts in chargeability parameters, towards a quantitative analysis of the investigated media, which allows for detailed soil- and rock-type characterization. Two major limitations restrict the extraction of the spectral information of TDIP data in the field: (i) the difficulty of acquiring reliable early-time measurements in the millisecond range and (ii) the self-potential background drift in the measured potentials distorting the shape of the late-time IP responses, in the second range. Recent developments in TDIP acquisition equipment have given access to full-waveform recordings of measured potentials and transmitted current, opening for a breakthrough in data processing. For measuring at early times, we developed a new method for removing the significant noise from power lines contained in the data through a model-based approach, localizing the fundamental frequency of the power-line signal in the full-waveform IP recordings. By this, we cancel both the fundamental signal and its harmonics. Furthermore, an efficient processing scheme for identifying and removing spikes in TDIP data was developed. The noise cancellation and the de-spiking allow the use of earlier and narrower gates, down to a few milliseconds after the current turn-off. In addition, tapered windows are used in the final gating of IP data, allowing the use of wider and overlapping gates for higher noise suppression with minimal distortion of the signal. For measuring at late times, we have developed an algorithm for removal of the self-potential drift. Usually constant or linear drift-removal algorithms are used, but these algorithms often fail in removing the background potentials present when the electrodes used for potential readings are previously used for current injection, also for simple contact resistance measurements. We developed a drift-removal scheme that models the polarization effect and efficiently allows for preserving the shape of the IP responses at late times. Uncertainty estimates are essential in the inversion of IP data. Therefore, in the final step of the data processing, we estimate the data standard deviation based on the data variability within the IP gates and the misfit of the background drift removal Overall, the removal of harmonic noise, spikes, self-potential drift, tapered windowing and the uncertainty estimation allows for doubling the usable range of TDIP data to almost four decades in time (corresponding to four decades in frequency), which will significantly advance the applicability of the IP method.

40 CFR 91.115 - Certification procedure-determining engine power and engine families.

Code of Federal Regulations, 2010 CFR

2010-07-01

... engine power and engine families. 91.115 Section 91.115 Protection of Environment ENVIRONMENTAL... ENGINES Emission Standards and Certification Provisions § 91.115 Certification procedure—determining engine power and engine families. (a) Engine power must be calculated using SAE J1228. This procedure has...

Geoeducation and Geoethics: Implications in natural hazards communication and preservation of architectonic heritage.

NASA Astrophysics Data System (ADS)

Pereira, Dolores; Martinez-Frías, Jesus; Mantovani, Franco

2014-05-01

In the framework of the ERASMUS Intensive Programme (IP) on "Global Heritage and Sustainability: Geological, Cultural and Historical", a round table was organised on "Geoeducation and Geoethics in Earth and Planetary Sciences" taking advantage of the role of the IP coordinator also being responsible for the "Heritage Stone Task Group" (HSTG) at IUGS and in addition the presence of the responsible for the "IUGS Commission on Geoscience Education, Training and Technology Transfer" (IUGS-COGE) and President of the International Association of Geoethics (IAGETH). Another responsible for the round table was an expert on natural risks. This topic formed an important part of the program of this IP, that in 2013 was celebrating its third and final edition. This round table was one of the first exchanges of views among different IUGS commissions and task groups. It offered a very good opportunity to analyse how aware is the scientific community about the importance of education and ethics in communicating natural hazards risks and their relationship preserving architectonic heritage, which was the main subject of the Intensive Programme. Eighteen participants contributed to the event with the following backgrounds: Geology, Engineering Geology, Architecture, Civil Engineering, Environmental Engineering, Civil Protection and English Philology. All participants were either undergraduate students or graduate students, at a Masters and Doctoral level from the following countries: Spain, Portugal, Italy and Hungary. The purpose of this study is to establish an initial link between geoethics and geoeducation when teaching university students at different levels of subject such as natural hazards risks communication and the preservation of architectonic heritage. The respective IUGS Commissions and Task Groups can lead the debate. This work was sponsored by the ERASMUS Intensive Programme 2012-1-ES1-ERA10-54375 and it was done within the framework of the IUGS Heritage Stone Task Group and COGE commission activities.

Comparative toxicity and efficacy of engineered anthrax lethal toxin variants with broad anti-tumor activities.

PubMed

Peters, Diane E; Hoover, Benjamin; Cloud, Loretta Grey; Liu, Shihui; Molinolo, Alfredo A; Leppla, Stephen H; Bugge, Thomas H

2014-09-01

We have previously designed and characterized versions of anthrax lethal toxin that are selectively cytotoxic in the tumor microenvironment and which display broad and potent anti-tumor activities in vivo. Here, we have performed the first direct comparison of the safety and efficacy of three engineered anthrax lethal toxin variants requiring activation by either matrix-metalloproteinases (MMPs), urokinase plasminogen activator (uPA) or co-localized MMP/uPA activities. C57BL/6J mice were challenged with six doses of engineered toxins via intraperitoneal (I.P.) or intravenous (I.V.) dose routes to determine the maximum tolerated dose for six administrations (MTD6) and dose-limiting toxicities. Efficacy was evaluated using the B16-BL6 syngraft model of melanoma; mice bearing established tumors were treated with six I.P. doses of toxin and tumor measurements and immunohistochemistry, paired with terminal blood work, were used to elaborate upon the anti-tumor mechanism and relative efficacy of each variant. We found that MMP-, uPA- and dual MMP/uPA-activated anthrax lethal toxins exhibited the same dose-limiting toxicity; dose-dependent GI toxicity. In terms of efficacy, all three toxins significantly reduced primary B16-BL6 tumor burden, ranging from 32% to 87% reduction, and they also delayed disease progression as evidenced by dose-dependent normalization of blood work values. While target organ toxicity and effective doses were similar amongst the variants, the dual MMP/uPA-activated anthrax lethal toxin exhibited the highest I.P. MTD6 and was 1.5-3-fold better tolerated than the single MMP- and uPA-activated toxins. Overall, we demonstrate that this dual MMP/uPA-activated anthrax lethal toxin can be administered safely and is highly effective in a preclinical model of melanoma. This modified bacterial cytotoxin is thus a promising candidate for further clinical development and evaluation for use in treating human cancers. Published by Elsevier Inc.

Comparative toxicity and efficacy of engineered anthrax lethal toxin variants with broad anti-tumor activities

PubMed Central

Peters, Diane E.; Hoover, Benjamin; Cloud, Loretta Grey; Liu, Shihui; Molinolo, Alfredo A.; Leppla, Stephen H.; Bugge, Thomas H.

2014-01-01

We have previously designed and characterized versions of anthrax lethal toxin that are selectively cytotoxic in the tumor microenvironment and which display broad and potent anti-tumor activities in vivo. Here, we have performed the first direct comparison of the safety and efficacy of three engineered anthrax lethal toxin variants requiring activation by either matrix-metalloproteinases (MMPs), urokinase plasminogen activator (uPA) or co-localized MMP/uPA activities. C57BL/6J mice were challenged with six doses of engineered toxins via intraperitoneal (I.P.) or intravenous (I.V.) dose routes to determine the maximum tolerated dose for six administrations (MTD6) and dose-limiting toxicities. Efficacy was evaluated using the B16-BL6 syngraft model of melanoma; Mice bearing established tumors were treated with six I.P. doses of toxin and tumor measurements and immunohistochemistry, paired with terminal blood work, were used to elaborate upon the anti-tumor mechanism and relative efficacy of each variant. We found that MMP-, uPA- and dual MMP/uPA- activated anthrax lethal toxins exhibited the same dose-limiting toxicity; dose-dependent GI toxicity. In terms of efficacy, all three toxins significantly reduced primary B16-BL6 tumor burden, ranging from 32%–87% reduction, and they also delayed disease progression as evidenced by dose-dependent normalization of blood work values. While target organ toxicity and effective doses were similar amongst the variants, the dual MMP/uPA-activated anthrax lethal toxin exhibited the highest I.P. MTD6 and was 1.5–3-fold better tolerated than the single MMP- and uPA-activated toxins. Overall, we demonstrate that this dual MMP/uPA-activated anthrax lethal toxin can be administered safely and is highly effective in a preclinical model of melanoma. This modified bacterial cytotoxin is thus a promising candidate for further clinical development and evaluation for use in treating human cancers. PMID:24971906

Chromatin analyses of Zymoseptoria tritici: Methods for chromatin immunoprecipitation followed by high-throughput sequencing (ChIP-seq).

PubMed

Soyer, Jessica L; Möller, Mareike; Schotanus, Klaas; Connolly, Lanelle R; Galazka, Jonathan M; Freitag, Michael; Stukenbrock, Eva H

2015-06-01

The presence or absence of specific transcription factors, chromatin remodeling machineries, chromatin modification enzymes, post-translational histone modifications and histone variants all play crucial roles in the regulation of pathogenicity genes. Chromatin immunoprecipitation (ChIP) followed by high-throughput sequencing (ChIP-seq) provides an important tool to study genome-wide protein-DNA interactions to help understand gene regulation in the context of native chromatin. ChIP-seq is a convenient in vivo technique to identify, map and characterize occupancy of specific DNA fragments with proteins against which specific antibodies exist or which can be epitope-tagged in vivo. We optimized existing ChIP protocols for use in the wheat pathogen Zymoseptoria tritici and closely related sister species. Here, we provide a detailed method, underscoring which aspects of the technique are organism-specific. Library preparation for Illumina sequencing is described, as this is currently the most widely used ChIP-seq method. One approach for the analysis and visualization of representative sequence is described; improved tools for these analyses are constantly being developed. Using ChIP-seq with antibodies against H3K4me2, which is considered a mark for euchromatin or H3K9me3 and H3K27me3, which are considered marks for heterochromatin, the overall distribution of euchromatin and heterochromatin in the genome of Z. tritici can be determined. Our ChIP-seq protocol was also successfully applied to Z. tritici strains with high levels of melanization or aberrant colony morphology, and to different species of the genus (Z. ardabiliae and Z. pseudotritici), suggesting that our technique is robust. The methods described here provide a powerful framework to study new aspects of chromatin biology and gene regulation in this prominent wheat pathogen. Copyright © 2015 Elsevier Inc. All rights reserved.

Nuclear Reactor Accident Fallout Artifacts: Unusual Black Spots on Digital Radiographs.

PubMed

Kashimura, Yasuhiro; Chida, Koichi

2015-12-01

The Fukushima nuclear power plant accident resulted in the discharge of radioactive particulate material into the atmosphere. Consequently, several hospitals in Japan have observed black spots on x-ray computed radiography (CR) images caused by particulate radioactive fallout. These black spots have no effect on human health. To reduce the influence of black spots on CR images, we need to erase latent images on imaging plates (IPs) immediately before clinical use and read the IPs soon after the x-ray examination. Alternatively, the contaminated felt of a cassette can be cleaned or exchanged, if possible.

Practical Integration-Free Episomal Methods for Generating Human Induced Pluripotent Stem Cells.

PubMed

Kime, Cody; Rand, Tim A; Ivey, Kathryn N; Srivastava, Deepak; Yamanaka, Shinya; Tomoda, Kiichiro

2015-10-06

The advent of induced pluripotent stem (iPS) cell technology has revolutionized biomedicine and basic research by yielding cells with embryonic stem (ES) cell-like properties. The use of iPS-derived cells for cell-based therapies and modeling of human disease holds great potential. While the initial description of iPS cells involved overexpression of four transcription factors via viral vectors that integrated within genomic DNA, advances in recent years by our group and others have led to safer and higher quality iPS cells with greater efficiency. Here, we describe commonly practiced methods for non-integrating induced pluripotent stem cell generation using nucleofection of episomal reprogramming plasmids. These methods are adapted from recent studies that demonstrate increased hiPS cell reprogramming efficacy with the application of three powerful episomal hiPS cell reprogramming factor vectors and the inclusion of an accessory vector expressing EBNA1. Copyright © 2015 John Wiley & Sons, Inc.

Spectral F-test power evaluation in the EEG during intermittent photic stimulation.

PubMed

de Sá, Antonio Mauricio F L Miranda; Cagy, Mauricio; Lazarev, Vladimir V; Infantosi, Antonio Fernando C

2006-06-01

Intermittent photic stimulation (IPS) is an important functional test, which can induce the photic driving in the electroencephalogram (EEG). It is capable of enhancing latent oscillations manifestations not present in the resting EEG. However, for adequate quantitative evaluation of the photic driving, these changes should be assessed on a statistical basis. With this aim, the sampling distribution of spectral F test was investigated. On this basis, confidence limits of the SFT-estimate could be obtained for different practical situations, in which the signal-to-noise ratio and the number of epochs used in the estimation may vary. The technique was applied to the EEG of 10 normal subjects during IPS, and allowed detecting responses not only at the fundamental IPS frequency but also at higher harmonics. It also permitted to assess the strength of the photic driving responses and to compare them in different derivations and in different subjects.

Three-dimensional lattice matching of epitaxially embedded nanoparticles

NASA Astrophysics Data System (ADS)

May, Brelon J.; Anderson, Peter M.; Myers, Roberto C.

2017-02-01

For a given degree of in-plane lattice mismatch between a two-dimensional (2D) epitaxial layer and a substrate (ɛIP*), there is a critical thickness above which interfacial defects form to relax the elastic strain energy. Here, we extend the 2D lattice-matching conditions to three-dimensions in order to predict the critical size beyond which epitaxially encased nanoparticles, characterized by both ɛIP* and out-of-plane lattice mismatch (ɛOP*), relax by dislocation formation. The critical particle length (Lc) at which defect formation proceeds is determined by balancing the reduction in elastic energy associated with dislocation introduction with the corresponding increase in defect energy. Our results, which use a modified Eshelby inclusion technique for an embedded, arbitrarily-faceted nanoparticle, provide new insight to the nanoepitaxy of low dimensional structures, especially quantum dots and nanoprecipitates. By engineering ɛIP* and ɛOP* , the predicted Lc for nanoparticles can be increased to well beyond the case of encapsulation in a homogenous matrix. For the case of truncated pyramidal shaped InAs, Lc 10.8 nm when fully embedded in GaAs (ɛIP* = ɛOP* = - 0.072); 16.4 nm when the particle is grown on GaAs, but capped with InSb (ɛIP* = - 0.072 and ɛOP* =+0.065); and a maximum of 18.4 nm if capped with an alloy corresponding to ɛOP* =+0.037. The effect, which we term "3D Poisson-stabilization" provides a means to increase the epitaxial strain tolerance in epitaxial heterostructures by tailoring ɛOP*.

Telemetry Standards, RCC Standard 106-17, Chapter 27, RF Network Access Layer

DTIC Science & Technology

2017-07-01

27-13 27.5.5 Frame Check Sequence Field........................................................................... 27-13 27.6 Power Transients...to the physical media (i.e., the wireless RF network). On the transmission side, it is responsible for framing IP packets for physical transmission...parameters of a radio shall be stored to maintain communications with RF link management after a power interruption or software-initiated reset

ePIANNO: ePIgenomics ANNOtation tool.

PubMed

Liu, Chia-Hsin; Ho, Bing-Ching; Chen, Chun-Ling; Chang, Ya-Hsuan; Hsu, Yi-Chiung; Li, Yu-Cheng; Yuan, Shin-Sheng; Huang, Yi-Huan; Chang, Chi-Sheng; Li, Ker-Chau; Chen, Hsuan-Yu

2016-01-01

Recently, with the development of next generation sequencing (NGS), the combination of chromatin immunoprecipitation (ChIP) and NGS, namely ChIP-seq, has become a powerful technique to capture potential genomic binding sites of regulatory factors, histone modifications and chromatin accessible regions. For most researchers, additional information including genomic variations on the TF binding site, allele frequency of variation between different populations, variation associated disease, and other neighbour TF binding sites are essential to generate a proper hypothesis or a meaningful conclusion. Many ChIP-seq datasets had been deposited on the public domain to help researchers make new discoveries. However, researches are often intimidated by the complexity of data structure and largeness of data volume. Such information would be more useful if they could be combined or downloaded with ChIP-seq data. To meet such demands, we built a webtool: ePIgenomic ANNOtation tool (ePIANNO, http://epianno.stat.sinica.edu.tw/index.html). ePIANNO is a web server that combines SNP information of populations (1000 Genomes Project) and gene-disease association information of GWAS (NHGRI) with ChIP-seq (hmChIP, ENCODE, and ROADMAP epigenomics) data. ePIANNO has a user-friendly website interface allowing researchers to explore, navigate, and extract data quickly. We use two examples to demonstrate how users could use functions of ePIANNO webserver to explore useful information about TF related genomic variants. Users could use our query functions to search target regions, transcription factors, or annotations. ePIANNO may help users to generate hypothesis or explore potential biological functions for their studies.

The impact of the duration of an untreated episode on improvement of depression and somatic symptoms

PubMed Central

Hung, Ching-I; Yu, Nan-Wen; Liu, Chia-Yih; Wu, Kuan-Yi; Yang, Ching-Hui

2015-01-01

Purpose The aim of this study was to investigate the impact of the duration of an untreated episode (DUE) on the improvement of depression and somatic symptoms among patients with major depressive disorder (MDD), after the patients had received 4 weeks of pharmacotherapy. Methods In this open-label study, there were 155 participants with MDD who were treated daily with 75 mg of venlafaxine for 4 weeks. DUE was defined as the interval between the onset of the index major depressive episode and the start of pharmacotherapy. The Depression and Somatic Symptoms Scale (DSSS), composed of the depression subscale (DS) and the somatic subscale (SS), was used. The SS included the pain subscale (PS) and the nonpain somatic subscale (NPSS). Multiple linear regressions were used to test the impacts of DUE on the improvement percentages (IPs) of depression and somatic symptoms. Results Eighty-five subjects completed the 4-week treatment. The IPs of the DS, SS, and NPSS were significantly negatively correlated with DUE. A shorter DUE was related to higher IPs. DUE was an independent factor, predicting the IPs of the DS, SS, and NPSS. DUE <1 month was the most powerful time-point to predict the IPs of the DS, SS, and NPSS. However, DUE was unable to predict the IP of the PS at all time-points. Conclusion A shorter DUE might be one of the factors related to greater improvement of depression and somatic symptoms. DUE should be considered as an important factor when investigating the prognosis of depression and somatic symptoms. PMID:26346571

The impact of the duration of an untreated episode on improvement of depression and somatic symptoms.

PubMed

Hung, Ching-I; Yu, Nan-Wen; Liu, Chia-Yih; Wu, Kuan-Yi; Yang, Ching-Hui

2015-01-01

The aim of this study was to investigate the impact of the duration of an untreated episode (DUE) on the improvement of depression and somatic symptoms among patients with major depressive disorder (MDD), after the patients had received 4 weeks of pharmacotherapy. In this open-label study, there were 155 participants with MDD who were treated daily with 75 mg of venlafaxine for 4 weeks. DUE was defined as the interval between the onset of the index major depressive episode and the start of pharmacotherapy. The Depression and Somatic Symptoms Scale (DSSS), composed of the depression subscale (DS) and the somatic subscale (SS), was used. The SS included the pain subscale (PS) and the nonpain somatic subscale (NPSS). Multiple linear regressions were used to test the impacts of DUE on the improvement percentages (IPs) of depression and somatic symptoms. Eighty-five subjects completed the 4-week treatment. The IPs of the DS, SS, and NPSS were significantly negatively correlated with DUE. A shorter DUE was related to higher IPs. DUE was an independent factor, predicting the IPs of the DS, SS, and NPSS. DUE <1 month was the most powerful time-point to predict the IPs of the DS, SS, and NPSS. However, DUE was unable to predict the IP of the PS at all time-points. A shorter DUE might be one of the factors related to greater improvement of depression and somatic symptoms. DUE should be considered as an important factor when investigating the prognosis of depression and somatic symptoms.

A Lifting Surface Theory for Wings Experiencing Leading-Edge Separation

DTIC Science & Technology

1977-06-30

CSR -CHCRÜ TO SPAN RATIO N-l N’SECIION NO. INDICAIOR FORM SCALES TO KURHALUt E0U»T|CNS Fl • 2.» ALEA /IP|»P| I fi ■ AIFA...Documentation Center Cameron Station, Bldg. 5 Alexandria, VA 22314 12 Nielsen Engineering & Research, Inc. 510 Clyde Avenue Mountain View, CA 94043 1 RASA

Unveiling combinatorial regulation through the combination of ChIP information and in silico cis-regulatory module detection

PubMed Central

Sun, Hong; Guns, Tias; Fierro, Ana Carolina; Thorrez, Lieven; Nijssen, Siegfried; Marchal, Kathleen

2012-01-01

Computationally retrieving biologically relevant cis-regulatory modules (CRMs) is not straightforward. Because of the large number of candidates and the imperfection of the screening methods, many spurious CRMs are detected that are as high scoring as the biologically true ones. Using ChIP-information allows not only to reduce the regions in which the binding sites of the assayed transcription factor (TF) should be located, but also allows restricting the valid CRMs to those that contain the assayed TF (here referred to as applying CRM detection in a query-based mode). In this study, we show that exploiting ChIP-information in a query-based way makes in silico CRM detection a much more feasible endeavor. To be able to handle the large datasets, the query-based setting and other specificities proper to CRM detection on ChIP-Seq based data, we developed a novel powerful CRM detection method ‘CPModule’. By applying it on a well-studied ChIP-Seq data set involved in self-renewal of mouse embryonic stem cells, we demonstrate how our tool can recover combinatorial regulation of five known TFs that are key in the self-renewal of mouse embryonic stem cells. Additionally, we make a number of new predictions on combinatorial regulation of these five key TFs with other TFs documented in TRANSFAC. PMID:22422841

Chromatin immunoprecipitation assays: application of ChIP-on-chip for defining dynamic transcriptional mechanisms in bone cells.

PubMed

van der Deen, Margaretha; Hassan, Mohammad Q; Pratap, Jitesh; Teplyuk, Nadiya M; Young, Daniel W; Javed, Amjad; Zaidi, Sayyed K; Lian, Jane B; Montecino, Martin; Stein, Janet L; Stein, Gary S; van Wijnen, Andre J

2008-01-01

Normal cell growth and differentiation of bone cells requires the sequential expression of cell type specific genes to permit lineage specification and development of cellular phenotypes. Transcriptional activation and repression of distinct sets of genes support the anabolic functions of osteoblasts and the catabolic properties of osteoclasts. Furthermore, metastasis of tumors to the bone environment is controlled by transcriptional mechanisms. Insights into the transcriptional regulation of genes in bone cells may provide a conceptual basis for improved therapeutic approaches to treat bone fractures, genetic osteopathologies, and/or cancer metastases to bone. Chromatin immunoprecipitation (ChIP) is a powerful technique to establish in vivo binding of transcription factors to the promoters of genes that are either activated or repressed in bone cells. Combining ChIP with genomic microarray analysis, colloquially referred to as "ChIP-on-chip," has become a valuable method for analysis of endogenous protein/DNA interactions. This technique permits assessment of chromosomal binding sites for transcription factors or the location of histone modifications at a genomic scale. This chapter discusses protocols for performing chromatin immunoprecipitation experiments, with a focus on ChIP-on-chip analysis. The information presented is based on the authors' experience with defining interactions of Runt-related (RUNX) transcription factors with bone-related genes within the context of the native nucleosomal organization of intact osteoblastic cells.

Systematic evaluation of the impact of ChIP-seq read designs on genome coverage, peak identification, and allele-specific binding detection.

PubMed

Zhang, Qi; Zeng, Xin; Younkin, Sam; Kawli, Trupti; Snyder, Michael P; Keleş, Sündüz

2016-02-24

Chromatin immunoprecipitation followed by sequencing (ChIP-seq) experiments revolutionized genome-wide profiling of transcription factors and histone modifications. Although maturing sequencing technologies allow these experiments to be carried out with short (36-50 bps), long (75-100 bps), single-end, or paired-end reads, the impact of these read parameters on the downstream data analysis are not well understood. In this paper, we evaluate the effects of different read parameters on genome sequence alignment, coverage of different classes of genomic features, peak identification, and allele-specific binding detection. We generated 101 bps paired-end ChIP-seq data for many transcription factors from human GM12878 and MCF7 cell lines. Systematic evaluations using in silico variations of these data as well as fully simulated data, revealed complex interplay between the sequencing parameters and analysis tools, and indicated clear advantages of paired-end designs in several aspects such as alignment accuracy, peak resolution, and most notably, allele-specific binding detection. Our work elucidates the effect of design on the downstream analysis and provides insights to investigators in deciding sequencing parameters in ChIP-seq experiments. We present the first systematic evaluation of the impact of ChIP-seq designs on allele-specific binding detection and highlights the power of pair-end designs in such studies.

Mapping the patent landscape of synthetic biology for fine chemical production pathways.

PubMed

Carbonell, Pablo; Gök, Abdullah; Shapira, Philip; Faulon, Jean-Loup

2016-09-01

A goal of synthetic biology bio-foundries is to innovate through an iterative design/build/test/learn pipeline. In assessing the value of new chemical production routes, the intellectual property (IP) novelty of the pathway is important. Exploratory studies can be carried using knowledge of the patent/IP landscape for synthetic biology and metabolic engineering. In this paper, we perform an assessment of pathways as potential targets for chemical production across the full catalogue of reachable chemicals in the extended metabolic space of chassis organisms, as computed by the retrosynthesis-based algorithm RetroPath. Our database for reactions processed by sequences in heterologous pathways was screened against the PatSeq database, a comprehensive collection of more than 150M sequences present in patent grants and applications. We also examine related patent families using Derwent Innovations. This large-scale computational study provides useful insights into the IP landscape of synthetic biology for fine and specialty chemicals production. © 2016 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

Determining optimal torsional ultrasound power for cataract surgery with automatic longitudinal pulses at maximum vacuum ex vivo.

PubMed

Ronquillo, Cecinio C; Zaugg, Brian; Stagg, Brian; Kirk, Kevin R; Gupta, Isha; Barlow, William R; Pettey, Jeff H; Olson, Randall J

2014-12-01

To determine the optimal longitudinal power settings for Infiniti OZil Intelligent Phaco (IP) at varying torsional amplitude settings; and to test the hypothesis that increasing longitudinal power is more important at lower torsional amplitudes to achieve efficient phacoemulsification. Laboratory investigation. setting: John A. Moran Eye Center, University of Utah, Salt Lake City, Utah. procedure: Individual porcine nuclei were fixed in formalin, then cut into 2.0 mm cubes. Lens cube phacoemulsification was done using OZil IP at 60%, 80%, and 100% torsional amplitude with 0%, 10%, 20%, 30%, 50%, 75%, or 100% longitudinal power. All experiments were done using a 20 gauge 0.9 mm bent reverse bevel phaco tip at constant vacuum (550 mm Hg), aspiration rate (40 mL/min), and bottle height (50 cm). main outcome measure: Complete lens particle phacoemulsification (efficiency). Linear regression analysis showed a significant increase in efficiency with increasing longitudinal power at 60% torsional amplitude (R(2) = 0.7269, P = .01) and 80% torsional amplitude (R(2) = 0.6995, P = .02) but not at 100% amplitude (R(2) = 0.3053, P = .2). Baseline comparison of 60% or 80% vs 100% torsional amplitude without longitudinal power showed increased efficiency at 100% (P = .0004). Increasing longitudinal power to 20% abolished the efficiency difference between 80% vs 100% amplitudes. In contrast, 75% longitudinal power abolished the efficiency difference between 60% vs 100% torsional amplitudes. Results suggest that longitudinal power becomes more critical at increasing phacoemulsification efficiencies at torsional amplitudes less than 100%. Increasing longitudinal power does not further increase efficiency at maximal torsional amplitudes. Copyright © 2014 Elsevier Inc. All rights reserved.

Mathematical modeling of intraperitoneal drug delivery: simulation of drug distribution in a single tumor nodule.

PubMed

Steuperaert, Margo; Falvo D'Urso Labate, Giuseppe; Debbaut, Charlotte; De Wever, Olivier; Vanhove, Christian; Ceelen, Wim; Segers, Patrick

2017-11-01

The intraperitoneal (IP) administration of chemotherapy is an alternative treatment for peritoneal carcinomatosis, allowing for higher intratumor concentrations of the cytotoxic agent compared to intravenous administration. Nevertheless, drug penetration depths are still limited to a few millimeters. It is thus necessary to better understand the limiting factors behind this poor penetration in order to improve IP chemotherapy delivery. By developing a three-dimensional computational fluid dynamics (CFD) model for drug penetration in a tumor nodule, we investigated the impact of a number of key parameters on the drug transport and penetration depth during IP chemotherapy. Overall, smaller tumors showed better penetration than larger ones, which could be attributed to the lower IFP in smaller tumors. Furthermore, the model demonstrated large improvements in penetration depth by subjecting the tumor nodules to vascular normalization therapy, and illustrated the importance of the drug that is used for therapy. Explicitly modeling the necrotic core had a limited effect on the simulated penetration. Similarly, the penetration depth remained virtually constant when the Darcy permeability of the tissue changed. Our findings illustrate that the developed parametrical CFD model is a powerful tool providing more insight in the drug transport and penetration during IP chemotherapy.

Polarized light microscopy for 3-dimensional mapping of collagen fiber architecture in ocular tissues.

PubMed

Yang, Bin; Jan, Ning-Jiun; Brazile, Bryn; Voorhees, Andrew; Lathrop, Kira L; Sigal, Ian A

2018-04-06

Collagen fibers play a central role in normal eye mechanics and pathology. In ocular tissues, collagen fibers exhibit a complex 3-dimensional (3D) fiber orientation, with both in-plane (IP) and out-of-plane (OP) orientations. Imaging techniques traditionally applied to the study of ocular tissues only quantify IP fiber orientation, providing little information on OP fiber orientation. Accurate description of the complex 3D fiber microstructures of the eye requires quantifying full 3D fiber orientation. Herein, we present 3dPLM, a technique based on polarized light microscopy developed to quantify both IP and OP collagen fiber orientations of ocular tissues. The performance of 3dPLM was examined by simulation and experimental verification and validation. The experiments demonstrated an excellent agreement between extracted and true 3D fiber orientation. Both IP and OP fiber orientations can be extracted from the sclera and the cornea, providing previously unavailable quantitative 3D measures and insight into the tissue microarchitecture. Together, the results demonstrate that 3dPLM is a powerful imaging technique for the analysis of ocular tissues. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Identification and removal of low-complexity sites in allele-specific analysis of ChIP-seq data.

PubMed

Waszak, Sebastian M; Kilpinen, Helena; Gschwind, Andreas R; Orioli, Andrea; Raghav, Sunil K; Witwicki, Robert M; Migliavacca, Eugenia; Yurovsky, Alisa; Lappalainen, Tuuli; Hernandez, Nouria; Reymond, Alexandre; Dermitzakis, Emmanouil T; Deplancke, Bart

2014-01-15

High-throughput sequencing technologies enable the genome-wide analysis of the impact of genetic variation on molecular phenotypes at unprecedented resolution. However, although powerful, these technologies can also introduce unexpected artifacts. We investigated the impact of library amplification bias on the identification of allele-specific (AS) molecular events from high-throughput sequencing data derived from chromatin immunoprecipitation assays (ChIP-seq). Putative AS DNA binding activity for RNA polymerase II was determined using ChIP-seq data derived from lymphoblastoid cell lines of two parent-daughter trios. We found that, at high-sequencing depth, many significant AS binding sites suffered from an amplification bias, as evidenced by a larger number of clonal reads representing one of the two alleles. To alleviate this bias, we devised an amplification bias detection strategy, which filters out sites with low read complexity and sites featuring a significant excess of clonal reads. This method will be useful for AS analyses involving ChIP-seq and other functional sequencing assays. The R package abs filter for library clonality simulations and detection of amplification-biased sites is available from http://updepla1srv1.epfl.ch/waszaks/absfilter

A hierarchical clustering scheme approach to assessment of IP-network traffic using detrended fluctuation analysis

NASA Astrophysics Data System (ADS)

Takuma, Takehisa; Masugi, Masao

2009-03-01

This paper presents an approach to the assessment of IP-network traffic in terms of the time variation of self-similarity. To get a comprehensive view in analyzing the degree of long-range dependence (LRD) of IP-network traffic, we use a hierarchical clustering scheme, which provides a way to classify high-dimensional data with a tree-like structure. Also, in the LRD-based analysis, we employ detrended fluctuation analysis (DFA), which is applicable to the analysis of long-range power-law correlations or LRD in non-stationary time-series signals. Based on sequential measurements of IP-network traffic at two locations, this paper derives corresponding values for the LRD-related parameter α that reflects the degree of LRD of measured data. In performing the hierarchical clustering scheme, we use three parameters: the α value, average throughput, and the proportion of network traffic that exceeds 80% of network bandwidth for each measured data set. We visually confirm that the traffic data can be classified in accordance with the network traffic properties, resulting in that the combined depiction of the LRD and other factors can give us an effective assessment of network conditions at different times.

Observation and analysis of halo current in EAST

NASA Astrophysics Data System (ADS)

Chen, Da-Long; Shen, Biao; Qian, Jin-Ping; Sun, You-Wen; Liu, Guang-Jun; Shi, Tong-Hui; Zhuang, Hui-Dong; Xiao, Bing-Jia

2014-06-01

Plasma in a typically elongated cross-section tokamak (for example, EAST) is inherently unstable against vertical displacement. When plasma loses the vertical position control, it moves downward or upward, leading to disruption, and a large halo current is generated helically in EAST typically in the scrape-off layer. When flowing into the vacuum vessel through in-vessel components, the halo current will give rise to a large J × B force acting on the vessel and the in-vessel components. In EAST VDE experiment, part of the eddy current is measured in halo sensors, due to the large loop voltage. Primary experimental data demonstrate that the halo current first lands on the outer plate and then flows clockwise, and the analysis of the information indicates that the maximum halo current estimated in EAST is about 0.4 times the plasma current and the maximum value of TPF × Ih/IP0 is 0.65, furthermore Ih/Ip0 and TPF × Ih/Ip0 tend to increase with the increase of Ip0. The test of the strong gas injection system shows good success in increasing the radiated power, which may be effective in reducing the halo current.

Salt Lake City Area Integrated Projects Electric Power Marketing. Draft environmental impact statement: Volume 4, Appendixes B-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-02-01

The Salt Lake City Area Office of the Western Area Power Administration (Western) markets electricity produced at hydroelectric facilities operated by the Bureau of Reclamation. The facilities are known collectively as the Salt Lake City Area Integrated Projects (SLCA/IP) and include dams equipped for power generation on the Green, Gunnison, Rio Grande, and Colorado rivers and on Deer and Plateau creeks in the states of Wyoming, Utah, Colorado, Arizona, and New Mexico. Of these facilities, only the Glen Canyon Unit, the Flaming Gorge Unit, and the Aspinall Unit (which includes Blue Mesa, Morrow Point, and Crystal dams;) are influenced bymore » Western power scheduling and transmission decisions. The EIS alternatives, called commitment-level alternatives, reflect combinations of capacity and energy that would feasibly and reasonably fulfill Westerns firm power marketing responsibilities, needs, and statutory obligations. The viability of these alternatives relates directly to the combination of generation capability of the SLCA/IP with energy purchases and interchange. The economic and natural resource assessments in this environmental impact statement (EIS) include an analysis of commitment-level alternatives. Impacts of the no-action alternative are also assessed. Supply options, which include combinations of electrical power purchases and hydropower operational scenarios reflecting different operations of the dams, are also assessed. The EIS evaluates the impacts of these scenarios relative to socioeconomics, air resources, water resources, ecological resources, cultural resources, land use, recreation, and visual resources.« less

Salt Lake City Area Integrated Projects Electric Power Marketing. Draft environmental impact statement: Volume 2, Sections 1-16

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Salt Lake City Area Office of the Western Area Power Administration (Western) markets electricity produced at hydroelectric facilities operated by the Bureau of Reclamation. The facilities are known collectively as the Salt Lake City Area Integrated Projects (SLCA/IP) and include dams equipped for power generation on the Green, Gunnison, Rio Grande, and Colorado rivers and on Deer and Plateau creeks in the states of Wyoming, Utah, Colorado, Arizona, and New Mexico. Of these facilities, only the Glen Canyon Unit, the Flaming Gorge Unit, and the Aspinall Unit (which includes Blue Mesa, Morrow Point, and Crystal dams;) are influenced bymore » Western power scheduling and transmission decisions. The EIS alternatives, called commitment-level alternatives, reflect combinations of capacity and energy that would feasibly and reasonably fulfill Westerns firm power marketing responsibilities, needs, and statutory obligations. The viability of these alternatives relates directly to the combination of generation capability of the SLCA/IP with energy purchases and interchange. The economic and natural resource assessments in this environmental impact statement (EIS) include an analysis of commitment-level alternatives. Impacts of the no-action alternative are also assessed. Supply options, which include combinations of electrical power purchases and hydropower operational scenarios reflecting different operations of the dams, are also assessed. The EIS evaluates the impacts of these scenarios relative to socioeconomics, air resources, water resources, ecological resources, cultural resources, land use, recreation, and visual resources.« less

An integrated workflow for analysis of ChIP-chip data.

PubMed

Weigelt, Karin; Moehle, Christoph; Stempfl, Thomas; Weber, Bernhard; Langmann, Thomas

2008-08-01

Although ChIP-chip is a powerful tool for genome-wide discovery of transcription factor target genes, the steps involving raw data analysis, identification of promoters, and correlation with binding sites are still laborious processes. Therefore, we report an integrated workflow for the analysis of promoter tiling arrays with the Genomatix ChipInspector system. We compare this tool with open-source software packages to identify PU.1 regulated genes in mouse macrophages. Our results suggest that ChipInspector data analysis, comparative genomics for binding site prediction, and pathway/network modeling significantly facilitate and enhance whole-genome promoter profiling to reveal in vivo sites of transcription factor-DNA interactions.

Advanced Simulation and Computing Fiscal Year 2016 Implementation Plan, Version 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCoy, M.; Archer, B.; Hendrickson, B.

2015-08-27

The Stockpile Stewardship Program (SSP) is an integrated technical program for maintaining the safety, surety, and reliability of the U.S. nuclear stockpile. The SSP uses nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of experimental facilities and programs, and the computational capabilities to support these programs. The purpose of this IP is to outline key work requirements to be performed and to control individualmore » work activities within the scope of work. Contractors may not deviate from this plan without a revised WA or subsequent IP.« less

75 FR 51987 - Birch Power Company and Sorenson Engineering; Birch Power Company and Sorenson Leasing L.L.C...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-24

... Company and Sorenson Engineering; Birch Power Company and Sorenson Leasing L.L.C.; Notice of Application..., 2010, Birch Power Company and Sorenson Engineering (transferors) and Birch Power Company and Sorenson.... Applicant Contact: For both: Mr. Ted S. Sorenson, President, Birch Power Company, Sorenson Engineering, and...

Operability test report for the in SITU vapor sampling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corbett, J.E., Westinghouse Hanford

1996-05-31

This report documents the successful completion of testing for the In Situ Vapor Sampling (ISVS) system. The report includes the test procedure (WHC-SD-WM-OTP-196, Rev OA), data sheets, exception resolutions, and a test report summary. This report conforms to the guidelines established in WHC-IP-1026, `Engineering Practice Guidelines,` Appendix L, `Operability Test Procedures and Reports.`

An Analytic Model of Gas Turbine Engine Installations.

DTIC Science & Technology

1984-09-01

CODE . . . . ............. 37 C. CTHiEi PROGRAM FEAL’RES . . . . . . . . . . . . 38 IV. RESULTS AJD RECOXEMNDTZCINS . . . . . . . . . . . 43 A GEN ER...IP(IIST.L.T.1.O) Go 0 7Q GO T3 55 C COMPU:Z FAN PRESSURE AND0 MATCH FAN PERFORMANCE 70 SYSTEM 70 FANC ;=(DP2𔃾.DP£45+DPi2L5.19696 croCf3ZDNIKC) c IF

Ship to Shore Data Communication and Prioritization

DTIC Science & Technology

2011-12-01

First Out FTP File Transfer Protocol GCCS-M Global Command and Control System Maritime HAIPE High Assurance Internet Protocol Encryptor HTTP Hypertext...Transfer Protocol (world wide web protocol ) IBS Integrated Bar Code System IDEF0 Integration Definition IER Information Exchange Requirements...INTEL Intelligence IP Internet Protocol IPT Integrated Product Team ISEA In-Service Engineering Agent ISNS Integrated Shipboard Network System IT

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2011 CFR

2011-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Side load on engine and auxiliary power...

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Side load on engine and auxiliary power...

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2013 CFR

2013-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Side load on engine and auxiliary power...

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2014 CFR

2014-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Side load on engine and auxiliary power...

14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.

Code of Federal Regulations, 2012 CFR

2012-01-01

... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Side load on engine and auxiliary power...

Performance Analysis of Power Saving Class of Type I for Voice Service in Two-Way Communication in IEEE 802.16e

NASA Astrophysics Data System (ADS)

Hwang, Eunju; Kim, Kyung Jae; Choi, Bong Dae

In IEEE 802.16e, power saving is one of the important issues for battery-powered mobile stations (MSs). We present a performance analysis of power saving class (PSC) of type I in IEEE 802.16e standard for voice over Internet protocol (VoIP) service with silence suppression in two-way communication. On-off pattern of a voice user in two-way communication is characterized by the modified Brady model, which includes short silence gaps less than 200ms and talkspurt periods shorter than 15ms, and so differs from the Brady model. Our analysis of PSC I follows the standard-based procedure for the deactivation of the sleep mode, where a uplink packet arrival during a mutual silence period wakes up the MS immediately while a downlink packet arrival waits to be served until the next listening window. We derive the delay distribution of the first downlink packet arriving during a mutual silence period, and find the dropping probability of downlink packets since a voice packet drops if it is not transmitted within maximum delay constraint. In addition, we calculate the average power consumption under the modified Brady model. Analysis and simulation results show that the sleep mode operation for the MS with VoIP service yields 32 ∼ 39% reduction in the power consumption of the MS. Finally we obtain the optimal initial/final-sleep windows that yield the minimum average power consumption while satisfying QoS constraints on the packet dropping probability and the maximum delay.

Improved Discovery of Molecular Interactions in Genome-Scale Data with Adaptive Model-Based Normalization

PubMed Central

Brown, Patrick O.

2013-01-01

Background High throughput molecular-interaction studies using immunoprecipitations (IP) or affinity purifications are powerful and widely used in biology research. One of many important applications of this method is to identify the set of RNAs that interact with a particular RNA-binding protein (RBP). Here, the unique statistical challenge presented is to delineate a specific set of RNAs that are enriched in one sample relative to another, typically a specific IP compared to a non-specific control to model background. The choice of normalization procedure critically impacts the number of RNAs that will be identified as interacting with an RBP at a given significance threshold – yet existing normalization methods make assumptions that are often fundamentally inaccurate when applied to IP enrichment data. Methods In this paper, we present a new normalization methodology that is specifically designed for identifying enriched RNA or DNA sequences in an IP. The normalization (called adaptive or AD normalization) uses a basic model of the IP experiment and is not a variant of mean, quantile, or other methodology previously proposed. The approach is evaluated statistically and tested with simulated and empirical data. Results and Conclusions The adaptive (AD) normalization method results in a greatly increased range in the number of enriched RNAs identified, fewer false positives, and overall better concordance with independent biological evidence, for the RBPs we analyzed, compared to median normalization. The approach is also applicable to the study of pairwise RNA, DNA and protein interactions such as the analysis of transcription factors via chromatin immunoprecipitation (ChIP) or any other experiments where samples from two conditions, one of which contains an enriched subset of the other, are studied. PMID:23349766

Validating a conceptual model for an inter-professional approach to shared decision making: a mixed methods study

PubMed Central

Légaré, France; Stacey, Dawn; Gagnon, Susie; Dunn, Sandy; Pluye, Pierre; Frosch, Dominick; Kryworuchko, Jennifer; Elwyn, Glyn; Gagnon, Marie-Pierre; Graham, Ian D

2011-01-01

Rationale, aims and objectives Following increased interest in having inter-professional (IP) health care teams engage patients in decision making, we developed a conceptual model for an IP approach to shared decision making (SDM) in primary care. We assessed the validity of the model with stakeholders in Canada. Methods In 15 individual interviews and 7 group interviews with 79 stakeholders, we asked them to: (1) propose changes to the IP-SDM model; (2) identify barriers and facilitators to the model's implementation in clinical practice; and (3) assess the model using a theory appraisal questionnaire. We performed a thematic analysis of the transcripts and a descriptive analysis of the questionnaires. Results Stakeholders suggested placing the patient at its centre; extending the concept of family to include significant others; clarifying outcomes; highlighting the concept of time; merging the micro, meso and macro levels in one figure; and recognizing the influence of the environment and emotions. The most common barriers identified were time constraints, insufficient resources and an imbalance of power among health professionals. The most common facilitators were education and training in inter-professionalism and SDM, motivation to achieve an IP approach to SDM, and mutual knowledge and understanding of disciplinary roles. Most stakeholders considered that the concepts and relationships between the concepts were clear and rated the model as logical, testable, having clear schematic representation, and being relevant to inter-professional collaboration, SDM and primary care. Conclusions Stakeholders validated the new IP-SDM model for primary care settings and proposed few modifications. Future research should assess if the model helps implement SDM in IP clinical practice. PMID:20695950

Validating a conceptual model for an inter-professional approach to shared decision making: a mixed methods study.

PubMed

Légaré, France; Stacey, Dawn; Gagnon, Susie; Dunn, Sandy; Pluye, Pierre; Frosch, Dominick; Kryworuchko, Jennifer; Elwyn, Glyn; Gagnon, Marie-Pierre; Graham, Ian D

2011-08-01

Following increased interest in having inter-professional (IP) health care teams engage patients in decision making, we developed a conceptual model for an IP approach to shared decision making (SDM) in primary care. We assessed the validity of the model with stakeholders in Canada. In 15 individual interviews and 7 group interviews with 79 stakeholders, we asked them to: (1) propose changes to the IP-SDM model; (2) identify barriers and facilitators to the model's implementation in clinical practice; and (3) assess the model using a theory appraisal questionnaire. We performed a thematic analysis of the transcripts and a descriptive analysis of the questionnaires. Stakeholders suggested placing the patient at its centre; extending the concept of family to include significant others; clarifying outcomes; highlighting the concept of time; merging the micro, meso and macro levels in one figure; and recognizing the influence of the environment and emotions. The most common barriers identified were time constraints, insufficient resources and an imbalance of power among health professionals. The most common facilitators were education and training in inter-professionalism and SDM, motivation to achieve an IP approach to SDM, and mutual knowledge and understanding of disciplinary roles. Most stakeholders considered that the concepts and relationships between the concepts were clear and rated the model as logical, testable, having clear schematic representation, and being relevant to inter-professional collaboration, SDM and primary care. Stakeholders validated the new IP-SDM model for primary care settings and proposed few modifications. Future research should assess if the model helps implement SDM in IP clinical practice. © 2010 Blackwell Publishing Ltd.

14 CFR 135.379 - Large transport category airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... engine powered: Takeoff limitations. 135.379 Section 135.379 Aeronautics and Space FEDERAL AVIATION... category airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine... existing at take- off. (b) No person operating a turbine engine powered large transport category airplane...

14 CFR 135.379 - Large transport category airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... engine powered: Takeoff limitations. 135.379 Section 135.379 Aeronautics and Space FEDERAL AVIATION... category airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine... existing at take- off. (b) No person operating a turbine engine powered large transport category airplane...

Effect of ionic activity products on the structure and composition of mineral self assembled on three-dimensional poly(lactide-co-glycolide) scaffolds

PubMed Central

Shin, Kyungsup; Jayasuriya, Ambalangodage C.; Kohn, David H.

2009-01-01

A biomimetic approach involving the self-assembly of mineral within the pores of three-dimensional porous polymer scaffolds is a promising strategy to integrate advantages of inorganic and organic phases into a single material for hard tissue engineering. Such a material enhances the ability of progenitor cells to differentiate down an osteoblast lineage in vitro and in vivo, compared with polymer scaffolds. The mechanisms regulating mineral formation in this one-step process, however, are poorly understood, especially the effects of ionic activity products (IP) of the mineralizing solution and incubation time. The aims of this study were to define the structure and composition of mineral formed within the pores of biodegradable polymer scaffolds as a function of IP and time. Three-dimensional poly(lactide-co-glycolide) scaffolds were fabricated by solvent casting/particulate leaching and incubated for 4–16 days in six variants of simulated body fluid whose IPs were varied by adjusting ionic concentrations. Scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy demonstrated the formation of carbonated apatite with sub-micrometer sized crystals that grew into spherical globules extending out of the scaffold pore surfaces. As IP increased, more mineral grew on the scaffold pore surfaces, but the apatite became less crystalline and the Ca/P molar ratio decreased from 1.63 ± 0.005 to 1.51 ± 0.002. Since morphology, composition, and structure of mineral are factors that affect cell function, this study demonstrates that the IP of the mineralizing solution is an important modulator of material properties, potentially leading to enhanced control of cell function. PMID:17584901

Pharmacokinetics and brain uptake of an IgG-TNF decoy receptor fusion protein following intravenous, intraperitoneal, and subcutaneous administration in mice.

PubMed

Sumbria, Rachita K; Zhou, Qing-Hui; Hui, Eric Ka-Wai; Lu, Jeff Zhiqiang; Boado, Ruben J; Pardridge, William M

2013-04-01

Tumor necrosis factor (TNF)-α is a proinflammatory cytokine active in the brain. Etanercept, the TNF decoy receptor (TNFR), does not cross the blood-brain barrier (BBB). The TNFR was re-engineered for BBB penetration as a fusion protein with a chimeric monoclonal antibody (mAb) against the mouse transferrin receptor (TfR), and this fusion protein is designated cTfRMAb-TNFR. The cTfRMAb domain of the fusion protein acts as a molecular Trojan horse and mediates transport via the endogenous BBB TfR. To support future chronic treatment of mouse models of neural disease with daily administration of the cTfRMAb-TNFR fusion protein, a series of pharmacokinetics and brain uptake studies in the mouse was performed. The cTfRMAb-TNFR fusion protein was radiolabeled and injected into mice via the intravenous, intraperitoneal (IP), or subcutaneous (SQ) routes of administration at doses ranging from 0.35 to 10 mg/kg. The distribution of the fusion protein into plasma following the IP or SQ routes was enhanced by increasing the injection dose from 3 to 10 mg/kg. The fusion protein demonstrated long circulation times with high metabolic stability following the IP or SQ routes of injection. The IP or SQ routes produced concentrations of the cTfRMAb-TNFR fusion protein in the brain that exceed by 20- to 50-fold the concentration of TNFα in pathologic conditions of the brain. The SQ injection is the preferred route of administration, as the level of cTfRMAb fusion protein produced in the brain is comparable to that generated with intravenous injection, and at a much lower plasma area under the concentration curve of the fusion protein as compared to IP administration.

Research requirements for emergency power to permit hover-one-engine-inoperative helicopter operation

NASA Technical Reports Server (NTRS)

Yost, J. H.

1976-01-01

The research and technology demonstration requirements to achieve emergency-power capability for a civil helicopter are documented. The goal for emergency power is the ability to hover with one engine inoperative, transition to minimum-power forward flight, and continue to a safe landing where emergency power may or may not be required. The best method to obtain emergency power is to augment the basic engine power by increasing the engine's speed and turbine-inlet temperature, combined with water-alcohol injection at the engine inlet. Other methods, including turbine boost power and flywheel energy, offer potential for obtaining emergency power for minimum time durations. Costs and schedules are estimated for a research and development program to bring emergency power through a hardware-demonstration test. Interaction of engine emergency-power capability with other helicopter systems is examined.

40 CFR 1039.140 - What is my engine's maximum engine power?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES... 1065, based on the manufacturer's design and production specifications for the engine. This information... power values for an engine are based on maximum engine power. For example, the group of engines with...

40 CFR 1039.140 - What is my engine's maximum engine power?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES... 1065, based on the manufacturer's design and production specifications for the engine. This information... power values for an engine are based on maximum engine power. For example, the group of engines with...

40 CFR 1039.140 - What is my engine's maximum engine power?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES... 1065, based on the manufacturer's design and production specifications for the engine. This information... power values for an engine are based on maximum engine power. For example, the group of engines with...

40 CFR 1039.140 - What is my engine's maximum engine power?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES... 1065, based on the manufacturer's design and production specifications for the engine. This information... power values for an engine are based on maximum engine power. For example, the group of engines with...

Free-piston Stirling technology for space power

NASA Technical Reports Server (NTRS)

Slaby, Jack G.

1989-01-01

An overview is presented of the NASA Lewis Research Center free-piston Stirling engine activities directed toward space power. This work is being carried out under NASA's new Civil Space Technology Initiative (CSTI). The overall goal of CSTI's High Capacity Power element is to develop the technology base needed to meet the long duration, high capacity power requirements for future NASA space missions. The Stirling cycle offers an attractive power conversion concept for space power needs. Discussed here is the completion of the Space Power Demonstrator Engine (SPDE) testing-culminating in the generation of 25 kW of engine power from a dynamically-balanced opposed-piston Stirling engine at a temperature ratio of 2.0. Engine efficiency was approximately 22 percent. The SPDE recently has been divided into two separate single-cylinder engines, called Space Power Research Engine (SPRE), that now serve as test beds for the evaluation of key technology disciplines. These disciplines include hydrodynamic gas bearings, high-efficiency linear alternators, space qualified heat pipe heat exchangers, oscillating flow code validation, and engine loss understanding.

Concept Design Report for a Low draft Stabilized - High Speed Connector (LDS-HSC) Vessel for the ONR High Speed Sea Lift (HSSL) Program

DTIC Science & Technology

2007-04-30

control of cushion air flow and, hence, control of cushion pressure fore and aft of the divider that provides significant dynamic control of ship pitch...fore and aft of the divider that provides significant dynamic control of ship pitch and heave in a seaway. All these modes of operation were tested by...Installed Power, SHP 402,306 Integrated Power System (IPS) featuring: * (6) 50 MW Rolls-Royce MT50 based Gensets Power Plant * Associated Conversion and

14 CFR 121.181 - Airplanes: Reciprocating engine-powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Reciprocating engine-powered: En... OPERATIONS Airplane Performance Operating Limitations § 121.181 Airplanes: Reciprocating engine-powered: En... person operating a reciprocating engine powered airplane may take off that airplane at a weight, allowing...

14 CFR 121.181 - Airplanes: Reciprocating engine-powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Reciprocating engine-powered: En... OPERATIONS Airplane Performance Operating Limitations § 121.181 Airplanes: Reciprocating engine-powered: En... person operating a reciprocating engine powered airplane may take off that airplane at a weight, allowing...

14 CFR 121.181 - Airplanes: Reciprocating engine-powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Reciprocating engine-powered: En... OPERATIONS Airplane Performance Operating Limitations § 121.181 Airplanes: Reciprocating engine-powered: En... person operating a reciprocating engine powered airplane may take off that airplane at a weight, allowing...

14 CFR 121.181 - Airplanes: Reciprocating engine-powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Reciprocating engine-powered: En... OPERATIONS Airplane Performance Operating Limitations § 121.181 Airplanes: Reciprocating engine-powered: En... person operating a reciprocating engine powered airplane may take off that airplane at a weight, allowing...

14 CFR 121.181 - Airplanes: Reciprocating engine-powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Reciprocating engine-powered: En... OPERATIONS Airplane Performance Operating Limitations § 121.181 Airplanes: Reciprocating engine-powered: En... person operating a reciprocating engine powered airplane may take off that airplane at a weight, allowing...

XML Tactical Chat (XTC): The Way Ahead for Navy Chat

DTIC Science & Technology

2007-09-01

multicast transmissions via sophisticated pruning algorithms, while allowing multicast packets to “ tunnel ” through IP routers. [Macedonia, Brutzman 1994...conference was Jabber Inc. who added some great insight into the power of Jabber. • Great features including blackberry handheld connectivity and

14 CFR 125.377 - Fuel supply: Turbine-engine-powered airplanes other than turbopropeller.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AIRCRAFT Flight Release Rules § 125.377 Fuel supply: Turbine-engine-powered airplanes other than... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Fuel supply: Turbine-engine-powered... or take off a turbine-engine powered airplane (other than a turbopropeller-powered airplane) unless...

14 CFR 125.377 - Fuel supply: Turbine-engine-powered airplanes other than turbopropeller.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AIRCRAFT Flight Release Rules § 125.377 Fuel supply: Turbine-engine-powered airplanes other than... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Fuel supply: Turbine-engine-powered... or take off a turbine-engine powered airplane (other than a turbopropeller-powered airplane) unless...

Energy attenuation performance of impact protection worn by motorcyclists in real-world crashes.

PubMed

Albanese, Bianca; Gibson, Tom; Whyte, Tom; Meredith, Lauren; Savino, Giovanni; de Rome, Liz; Baldock, Matthew; Fitzharris, Michael; Brown, Julie

2017-05-29

Laboratory studies have demonstrated that impact protectors (IP) used in motorcycle clothing can reduce fracture severities. While crash studies have reported IP are associated with reduced likelihood of soft tissue injury, there is little evidence of their effectiveness in reducing fracture likelihood. This discrepancy might be related to IP quality. There are mandatory requirements for IP supplied with protective clothing in Europe, but not elsewhere. This study examines the energy attenuation performance of IP used by Australian riders. IP were harvested from clothing worn by crashed riders admitted to hospital. The IP were examined and energy attenuation properties were determined using EN 1621-1 test procedures. Impact injury was identified from medical records and defined as fractures, dislocations, and avulsions that occurred following impact to the rider's shoulders, elbows, hips, and/or knees. Fisher's exact test was used to examine the relationship between meeting the EN 1621-1 energy attenuation requirements and impact injury. The association between the average and maximum transmitted force, and impact injury was examined using generalized estimating equations. Motorcycle riders were recruited as part of an in-depth crash study through three hospitals in New South Wales, Australia, between 2012 and 2014. Riders were interviewed, and engineers conducted site, vehicle, and clothing inspections. Clothing was collected, or identical garments were purchased. Clothing was inspected for 62 riders. Of these, 19 wore clothing incorporating 76 IP. Twenty-six of these were impacted in the crash event. Almost all impacted IP (96%) were CE marked, and most (83%) met Level 1 energy attenuation requirements of EN 1621-1 when tested. Of the 26 impacted IP, four were associated with impact injuries, including midshaft and distal clavicle fractures and a scapula and olecranon fracture. No associations between meeting EN 1621-1 requirements and impact injury were found (p = 0.5). There was no association between average force transmitted and impact injury (95% CI: 0.91-1.24); however, as maximum force transmitted increased, the odds of impact injury increased (95% CI: 1.01-1.2). These results indicate a high probability of impact injury at 50 kN, the limit of maximum transmitted force specified in EN 1621-1. The allowable transmitted force of EN 1621-1 may be too high to effectively reduce the probability of impact injury. This is not surprising, given human tolerance levels that are reported in literature. Reducing the force limit below the reported fracture tolerance limits might be difficult with current technology. However, there is scope to reduce the EN 1621-1 maximum limit of 50 kN transmitted force. A reduction in the maximum force limit would improve rider protection and appears feasible, as 77% of tested IP recorded a maximum force <35 kN. This level of transmitted force is estimated to be associated with <20% probability of impact injury. While the performance of IP available to Australian riders is not regulated, most IP was CE marked. The results indicate a significant association between maximum transmitted force, tested according to EN 1621-1 procedures, and impact injury. Further investigation of the EN 1621-1 requirements may be warranted. This work will interest those targeting protective equipment for motorcyclists as a mechanism for reducing injury to these vulnerable road users.

Network-wide BGP route prediction for traffic engineering

NASA Astrophysics Data System (ADS)

Feamster, Nick; Rexford, Jennifer

2002-07-01

The Internet consists of about 13,000 Autonomous Systems (AS's) that exchange routing information using the Border Gateway Protocol (BGP). The operators of each AS must have control over the flow of traffic through their network and between neighboring AS's. However, BGP is a complicated, policy-based protocol that does not include any direct support for traffic engineering. In previous work, we have demonstrated that network operators can adapt the flow of traffic in an efficient and predictable fashion through careful adjustments to the BGP policies running on their edge routers. Nevertheless, many details of the BGP protocol and decision process make predicting the effects of these policy changes difficult. In this paper, we describe a tool that predicts traffic flow at network exit points based on the network topology, the import policy associated with each BGP session, and the routing advertisements received from neighboring AS's. We present a linear-time algorithm that computes a network-wide view of the best BGP routes for each destination prefix given a static snapshot of the network state, without simulating the complex details of BGP message passing. We describe how to construct this snapshot using the BGP routing tables and router configuration files available from operational routers. We verify the accuracy of our algorithm by applying our tool to routing and configuration data from AT&T's commercial IP network. Our route prediction techniques help support the operation of large IP backbone networks, where interdomain routing is an important aspect of traffic engineering.

Speed And Power Control Of An Engine By Modulation Of The Load Torque

DOEpatents

Ziph, Benjamin; Strodtman, Scott; Rose, Thomas K

1999-01-26

A system and method of speed and power control for an engine in which speed and power of the engine is controlled by modulation of the load torque. The load torque is manipulated in order to cause engine speed, and hence power to be changed. To accomplish such control, the load torque undergoes a temporary excursion in the opposite direction of the desired speed and power change. The engine and the driven equipment will accelerate or decelerate accordingly as the load torque is decreased or increased, relative to the essentially fixed or constant engine torque. As the engine accelerates or decelerates, its power increases or decreases in proportion.

A method exploiting direct communication between phasor measurement units for power system wide-area protection and control algorithms.

PubMed

Almas, Muhammad Shoaib; Vanfretti, Luigi

2017-01-01

Synchrophasor measurements from Phasor Measurement Units (PMUs) are the primary sensors used to deploy Wide-Area Monitoring, Protection and Control (WAMPAC) systems. PMUs stream out synchrophasor measurements through the IEEE C37.118.2 protocol using TCP/IP or UDP/IP. The proposed method establishes a direct communication between two PMUs, thus eliminating the requirement of an intermediate phasor data concentrator, data mediator and/or protocol parser and thereby ensuring minimum communication latency without considering communication link delays. This method allows utilizing synchrophasor measurements internally in a PMU to deploy custom protection and control algorithms. These algorithms are deployed using protection logic equations which are supported by all the PMU vendors. Moreover, this method reduces overall equipment cost as the algorithms execute internally in a PMU and therefore does not require any additional controller for their deployment. The proposed method can be utilized for fast prototyping of wide-area measurements based protection and control applications. The proposed method is tested by coupling commercial PMUs as Hardware-in-the-Loop (HIL) with Opal-RT's eMEGAsim Real-Time Simulator (RTS). As illustrative example, anti-islanding protection application is deployed using proposed method and its performance is assessed. The essential points in the method are: •Bypassing intermediate phasor data concentrator or protocol parsers as the synchrophasors are communicated directly between the PMUs (minimizes communication delays).•Wide Area Protection and Control Algorithm is deployed using logic equations in the client PMU, therefore eliminating the requirement for an external hardware controller (cost curtailment)•Effortless means to exploit PMU measurements in an environment familiar to protection engineers.

14 CFR 135.383 - Large transport category airplanes: Turbine engine powered: En route limitations: Two engines...

Code of Federal Regulations, 2010 CFR

2010-01-01

... Limitations § 135.383 Large transport category airplanes: Turbine engine powered: En route limitations: Two...). No person may operate a turbine engine powered large transport category airplane along an intended..., 1958, but before August 30, 1959 (SR422A). No person may operate a turbine engine powered large...

14 CFR 135.383 - Large transport category airplanes: Turbine engine powered: En route limitations: Two engines...

Code of Federal Regulations, 2011 CFR

2011-01-01

... Limitations § 135.383 Large transport category airplanes: Turbine engine powered: En route limitations: Two...). No person may operate a turbine engine powered large transport category airplane along an intended..., 1958, but before August 30, 1959 (SR422A). No person may operate a turbine engine powered large...

Pressure ulcer incidence and progression in critically ill subjects: influence of low air loss mattress versus a powered air pressure redistribution mattress.

PubMed

Black, Joyce; Berke, Christine; Urzendowski, Gail

2012-01-01

The primary objective of this study was to compare facility-acquired pressure ulcer incidence and progression of pressure ulcers present on admission in critically ill patients, using 2 different support surfaces. We completed a comparison cohort study in a surgical intensive care unit (ICU). The study setting was a 12-bed cardiovascular ICU in a university-based hospital in the Midwestern United States. The sample comprised 52 critically ill patients; 31 were placed on low air loss weight-based pressure redistribution-microclimate management system beds and 21 were placed on integrated powered air pressure redistribution beds. Prior to the start of the study, 5 low airloss beds were placed in open rooms in the cardiovascular surgical ICU. Inclusion criteria were anticipated ICU stay of 3 days, and patients did not receive a speciality bed for pulmonary or wound issues. Initial assessment of the patients included risk assessment and prior events that would increase risk for pressure ulcer development such as extended time in operating room, along with skin assessment for existing pressure ulcers. Subjects in both groups had ongoing skin assessment every 3 to 4 days and a subjective evaluation of heel elevation and turning or repositioning by the researcher. Data were collected until the subjects were dismissed from the ICU. Patients admitted to the unit were assigned to open rooms following the usual protocols. The mean length of stay was 7.0 days, with an 8.1-day length of stay for subjects on "low air loss with microclimate management" beds (LAL-MCM) and 6.6 days on the integrated power pressure air redistribution (IP-AR) beds (P = NS). The incidence of pressure ulcers on the buttocks, sacrum, or coccyx was 0% (0/31) on the low air loss bed and 18% (4/21) on the IP-AR bed (P = .046). Five subjects had 6 pressure ulcers on admission. Two pressure ulcers on 2 patients worsened on the integrated power air redistribution beds, which required specialty bed rental costing the facility $4116. No subjects on the low air loss beds experienced worsening of existing pressure ulcer. One patient with a deep tissue injury present on admission improved on the LAL-MCM bed. The IP-AR beds were approximately 7 years old, and the LAL-MCM beds were new. Critically ill subjects placed on low air loss beds with microclimate management in surgical ICUs had a lower pressure ulcer incidence than those placed on integrated powered air pressure redistribution beds. The clinical performance of the IP-AR surfaces may have been influenced by their age.

Making the Transition to Three-Dimensional Teaching: An NGSS@NSTA Curator and Elementary Science Specialist Shares How to Evaluate Teaching Materials Using the EQuIP Rubric

ERIC Educational Resources Information Center

O'Day, Betsy

2016-01-01

Curriculum and lesson planning require the consideration of many things. With a shift to the "Next Generation Science Standards" ("NGSS"), integrating the dimensions of science and engineering practices, disciplinary core ideas, and crosscutting concepts becomes a focus of that planning. The author, Betsy O'Day, an elementary…

U.S. Army War College: Key Strategic Issues List

DTIC Science & Technology

2006-07-01

Protocol (EoIP) b. Soldier vs contractor operated and maintained tactical equipment. Are the new soldier systems so “ high tech ” that we cannot fight...approaches to meet the high tech skills demanded by our transformation TOEs? (G-3 ACD) 9. War and Society: a. Has the Army adapted from Industrial-Age to...61 United States Military Academy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 U.S. Army Corps of Engineers

A study to evaluate STS heads-up ascent trajectory performance employing a minimum-Hamiltonian optimization strategy

NASA Technical Reports Server (NTRS)

Sinha, Sujit

1988-01-01

A study was conducted to evaluate the performance implications of a heads-up ascent flight design for the Space Transportation System, as compared to the current heads-down flight mode. The procedure involved the use of the Minimum Hamiltonian Ascent Shuttle Trajectory Evaluation Program, which is a three-degree-of-freedom moment balance simulation of shuttle ascent. A minimum-Hamiltonian optimization strategy was employed to maximize injection weight as a function of maximum dynamic pressure constraint and Solid Rocket Motor burnrate. Performance Reference Mission Four trajectory groundrules were used for consistency. The major conclusions are that for heads-up ascent and a mission nominal design maximum dynamic pressure value of 680 psf, the optimum solid motor burnrate is 0.394 ips, which produces a performance enhancement of 4293 lbm relative to the baseline heads-down ascent, with 0.368 ips burnrate solid motors and a 680 psf dynamic pressure constraint. However, no performance advantage exists for heads-up flight if the current Solid Rocket Motor target burnrate of 0.368 ips is used. The advantage of heads-up ascent flight employing the current burnrate is that Space Shuttle Main Engine throttling for dynamic pressure control is not necessary.

Design of Intelligent Hydraulic Excavator Control System Based on PID Method

NASA Astrophysics Data System (ADS)

Zhang, Jun; Jiao, Shengjie; Liao, Xiaoming; Yin, Penglong; Wang, Yulin; Si, Kuimao; Zhang, Yi; Gu, Hairong

Most of the domestic designed hydraulic excavators adopt the constant power design method and set 85%~90% of engine power as the hydraulic system adoption power, it causes high energy loss due to mismatching of power between the engine and the pump. While the variation of the rotational speed of engine could sense the power shift of the load, it provides a new method to adjust the power matching between engine and pump through engine speed. Based on negative flux hydraulic system, an intelligent hydraulic excavator control system was designed based on rotational speed sensing method to improve energy efficiency. The control system was consisted of engine control module, pump power adjusted module, engine idle module and system fault diagnosis module. Special PLC with CAN bus was used to acquired the sensors and adjusts the pump absorption power according to load variation. Four energy saving control strategies with constant power method were employed to improve the fuel utilization. Three power modes (H, S and L mode) were designed to meet different working status; Auto idle function was employed to save energy through two work status detected pressure switches, 1300rpm was setting as the idle speed according to the engine consumption fuel curve. Transient overload function was designed for deep digging within short time without spending extra fuel. An increasing PID method was employed to realize power matching between engine and pump, the rotational speed's variation was taken as the PID algorithm's input; the current of proportional valve of variable displacement pump was the PID's output. The result indicated that the auto idle could decrease fuel consumption by 33.33% compared to work in maximum speed of H mode, the PID control method could take full use of maximum engine power at each power mode and keep the engine speed at stable range. Application of rotational speed sensing method provides a reliable method to improve the excavator's energy efficiency and realize power match between pump and engine.

Spacewire router IP-core with priority adaptive routing

NASA Astrophysics Data System (ADS)

Shakhmatov, A. V.; Chekmarev, S. A.; Vergasov, M. Y.; Khanov, V. Kh

2015-10-01

Design of modern spacecraft focuses on using network principles of interaction on-board equipment, in particular in network SpaceWire. Routers are an integral part of most SpaceWire networks. The paper presents an adaptive routing algorithm with a prioritization, allowing more flexibility to manage the routing process. This algorithm is designed to transmit SpaceWire packets over a redundant network. Also a method is proposed for rapid restoration of working capacity after power by saving the routing table and the router configuration in an external non-volatile memory. The proposed solutions used to create IP-core router, and then tested in the FPGA device. The results illustrate the realizability and rationality of the proposed solutions.

14 CFR 121.329 - Supplemental oxygen for sustenance: Turbine engine powered airplanes.

Code of Federal Regulations, 2011 CFR

2011-01-01

... engine powered airplanes. 121.329 Section 121.329 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... Equipment Requirements § 121.329 Supplemental oxygen for sustenance: Turbine engine powered airplanes. (a) General. When operating a turbine engine powered airplane, each certificate holder shall equip the...

14 CFR 121.329 - Supplemental oxygen for sustenance: Turbine engine powered airplanes.

Code of Federal Regulations, 2010 CFR

2010-01-01

... engine powered airplanes. 121.329 Section 121.329 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... Equipment Requirements § 121.329 Supplemental oxygen for sustenance: Turbine engine powered airplanes. (a) General. When operating a turbine engine powered airplane, each certificate holder shall equip the...

14 CFR 135.387 - Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2011 CFR

2011-01-01

....387 Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate... alternate airport for a turbine engine powered large transport category airplane unless (based on the... operators may select an airport as an alternate airport for a turbine engine powered large transport...

14 CFR 121.195 - Airplanes: Turbine engine powered: Landing limitations: Destination airports.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Turbine engine powered: Landing... Performance Operating Limitations § 121.195 Airplanes: Turbine engine powered: Landing limitations: Destination airports. (a) No person operating a turbine engine powered airplane may take off that airplane at...

14 CFR 91.1037 - Large transport category airplanes: Turbine engine powered; Limitations; Destination and...

Code of Federal Regulations, 2010 CFR

2010-01-01

....1037 Large transport category airplanes: Turbine engine powered; Limitations; Destination and alternate airports. (a) No program manager or any other person may permit a turbine engine powered large transport... and terrain. (c) A program manager or other person flying a turbine engine powered large transport...

14 CFR 121.195 - Airplanes: Turbine engine powered: Landing limitations: Destination airports.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Turbine engine powered: Landing... Performance Operating Limitations § 121.195 Airplanes: Turbine engine powered: Landing limitations: Destination airports. (a) No person operating a turbine engine powered airplane may take off that airplane at...

14 CFR 135.387 - Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2010 CFR

2010-01-01

....387 Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate... alternate airport for a turbine engine powered large transport category airplane unless (based on the... operators may select an airport as an alternate airport for a turbine engine powered large transport...

14 CFR 135.385 - Large transport category airplanes: Turbine engine powered: Landing limitations: Destination...

Code of Federal Regulations, 2011 CFR

2011-01-01

....385 Large transport category airplanes: Turbine engine powered: Landing limitations: Destination airports. (a) No person operating a turbine engine powered large transport category airplane may take off... this section, no person operating a turbine engine powered large transport category airplane may take...

14 CFR 91.1037 - Large transport category airplanes: Turbine engine powered; Limitations; Destination and...

Code of Federal Regulations, 2011 CFR

2011-01-01

....1037 Large transport category airplanes: Turbine engine powered; Limitations; Destination and alternate airports. (a) No program manager or any other person may permit a turbine engine powered large transport... and terrain. (c) A program manager or other person flying a turbine engine powered large transport...

14 CFR 135.385 - Large transport category airplanes: Turbine engine powered: Landing limitations: Destination...

Code of Federal Regulations, 2010 CFR

2010-01-01

....385 Large transport category airplanes: Turbine engine powered: Landing limitations: Destination airports. (a) No person operating a turbine engine powered large transport category airplane may take off... this section, no person operating a turbine engine powered large transport category airplane may take...

14 CFR 135.371 - Large transport category airplanes: Reciprocating engine powered: En route limitations: One...

Code of Federal Regulations, 2010 CFR

2010-01-01

... Limitations § 135.371 Large transport category airplanes: Reciprocating engine powered: En route limitations... reciprocating engine powered large transport category airplane may take off that airplane at a weight, allowing..., under an approved procedure, operate a reciprocating engine powered large transport category airplane at...

Advanced 35 W Free-Piston Stirling Engine for Space Power Applications

NASA Astrophysics Data System (ADS)

Wood, J. Gary; Lane, Neill

2003-01-01

This paper presents the projected performance and overall design characteristics of a high efficiency, low mass 35 W free-piston Stirling engine design. Overall (engine plus linear alternator) thermodynamic performance greater than 50% of Carnot, with a specific power close to 100 W/kg appears to be a reasonable goal at this small power level. Supporting test data and analysis results from exiting engines are presented. Design implications of high specific power in relatively low power engines is presented and discussed.

MST's Programmable Power Supplies: Bt Update, Bp Prototype

NASA Astrophysics Data System (ADS)

Holly, D. J.; Chapman, B. E.; McCollam, K. J.; Morin, J. C.; Thomas, M. A.

2013-10-01

MST's toroidal field programmable power supply (Bt PPS) has now been in operation for several years and has provided important new capabilities. One of the primary goals for the Bt PPS is the partial optimization of inductive current profile control, involving control of the poloidal electric field. The Bt PPS has achieved fluctuation reduction over MST's entire range of Ip. At the largest Ip, the Bt PPS achieves fluctuation reduction with a smaller poloidal electric field than the previous passive system, implying that substantially longer periods of current profile control may be possible. The Bt PPS has also been used to produce Ohmic tokamak plasmas in MST. With an applied toroidal field of 0.135 T, and q(a) > 2, the estimated energy confinement time is roughly consistent with neo-Alcator scaling. Driving q(a) < 2 with larger Ip, the confinement time degrades, but the discharge duration does not terminate prematurely. To fully optimize current profile control and to test MST operational limits, a PPS is also needed for the Bp circuit. Currently in prototype stage, the Bp PPS will feature a number of innovations to increase its flexibility and performance. Isolated charging, control, and monitor systems will eliminate charging relays, reduce coupling between modules, and minimize capacitor heating. Seven-level pulse width modulation will reduce output ripple and switching losses. Solid state shorting bars will eliminate shorting relays and minimize wiring. A balanced switching algorithm will minimize capacitive noise generation. Work supported by U. S. D. o. E.

Adaptation of Hybridization Capture of Chromatin-associated Proteins for Proteomics to Mammalian Cells.

PubMed

Guillen-Ahlers, Hector; Rao, Prahlad K; Perumalla, Danu S; Montoya, Maria J; Jadhav, Avinash Y L; Shortreed, Michael R; Smith, Lloyd M; Olivier, Michael

2018-06-01

The hybridization capture of chromatin-associated proteins for proteomics (HyCCAPP) technology was initially developed to uncover novel DNA-protein interactions in yeast. It allows analysis of a target region of interest without the need for prior knowledge about likely proteins bound to the target region. This, in theory, allows HyCCAPP to be used to analyze any genomic region of interest, and it provides sufficient flexibility to work in different cell systems. This method is not meant to study binding sites of known transcription factors, a task better suited for Chromatin Immunoprecipitation (ChIP) and ChIP-like methods. The strength of HyCCAPP lies in its ability to explore DNA regions for which there is limited or no knowledge about the proteins bound to it. It can also be a convenient method to avoid biases (present in ChIP-like methods) introduced by protein-based chromatin enrichment using antibodies. Potentially, HyCCAPP can be a powerful tool to uncover truly novel DNA-protein interactions. To date, the technology has been predominantly applied to yeast cells or to high copy repeat sequences in mammalian cells. In order to become the powerful tool we envision, HyCCAPP approaches need to be optimized to efficiently capture single-copy loci in mammalian cells. Here, we present our adaptation of the initial yeast HyCCAPP capture protocol to human cell lines, and show that single-copy chromatin regions can be efficiently isolated with this modified protocol.

Achieving Better Buying Power through Acquisition of Open Architecture Software Systems: Volume 1

DTIC Science & Technology

2016-01-06

supporting “Bring Your Own Devices” (BYOD)? 22 New business models for OA software components ● Franchising ● Enterprise licensing ● Metered usage...paths IP and cybersecurity requirements will need continuous attention! 35 New business models for OA software components ● Franchising ● Enterprise

Geometric Heat Engines Featuring Power that Grows with Efficiency.

PubMed

Raz, O; Subaşı, Y; Pugatch, R

2016-04-22

Thermodynamics places a limit on the efficiency of heat engines, but not on their output power or on how the power and efficiency change with the engine's cycle time. In this Letter, we develop a geometrical description of the power and efficiency as a function of the cycle time, applicable to an important class of heat engine models. This geometrical description is used to design engine protocols that attain both the maximal power and maximal efficiency at the fast driving limit. Furthermore, using this method, we also prove that no protocol can exactly attain the Carnot efficiency at nonzero power.

14 CFR 121.333 - Supplemental oxygen for emergency descent and for first aid; turbine engine powered airplanes...

Code of Federal Regulations, 2011 CFR

2011-01-01

... and for first aid; turbine engine powered airplanes with pressurized cabins. 121.333 Section 121.333... for emergency descent and for first aid; turbine engine powered airplanes with pressurized cabins. (a) General. When operating a turbine engine powered airplane with a pressurized cabin, the certificate holder...

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Turbine engine powered: Takeoff... Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine powered airplane may take off that airplane at a weight greater than that listed in the...

14 CFR 121.197 - Airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Turbine engine powered: Landing... Performance Operating Limitations § 121.197 Airplanes: Turbine engine powered: Landing limitations: Alternate... turbine engine powered airplane unless (based on the assumptions in § 121.195 (b)) that airplane at the...

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Turbine engine powered: Takeoff... Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine powered airplane may take off that airplane at a weight greater than that listed in the...

14 CFR 121.197 - Airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Turbine engine powered: Landing... Performance Operating Limitations § 121.197 Airplanes: Turbine engine powered: Landing limitations: Alternate... turbine engine powered airplane unless (based on the assumptions in § 121.195 (b)) that airplane at the...

14 CFR 121.333 - Supplemental oxygen for emergency descent and for first aid; turbine engine powered airplanes...

Code of Federal Regulations, 2010 CFR

2010-01-01

... and for first aid; turbine engine powered airplanes with pressurized cabins. 121.333 Section 121.333... for emergency descent and for first aid; turbine engine powered airplanes with pressurized cabins. (a) General. When operating a turbine engine powered airplane with a pressurized cabin, the certificate holder...

Optimization of OSPF Routing in IP Networks

NASA Astrophysics Data System (ADS)

Bley, Andreas; Fortz, Bernard; Gourdin, Eric; Holmberg, Kaj; Klopfenstein, Olivier; Pióro, Michał; Tomaszewski, Artur; Ümit, Hakan

The Internet is a huge world-wide packet switching network comprised of more than 13,000 distinct subnetworks, referred to as Autonomous Systems (ASs) autonomous system AS . They all rely on the Internet Protocol (IP) internet protocol IP for transport of packets across the network. And most of them use shortest path routing protocols shortest path routing!protocols , such as OSPF or IS-IS, to control the routing of IP packets routing!of IP packets within an AS. The idea of the routing is extremely simple — every packet is forwarded on IP links along the shortest route between its source and destination nodes of the AS. The AS network administrator can manage the routing of packets in the AS by supplying the so-called administrative weights of IP links, which specify the link lengths that are used by the routing protocols for their shortest path computations. The main advantage of the shortest path routing policy is its simplicity, allowing for little administrative overhead. From the network engineering perspective, however, shortest path routing can pose problems in achieving satisfactory traffic handling efficiency. As all routing paths depend on the same routing metric routing!metric , it is not possible to configure the routing paths for the communication demands between different pairs of nodes explicitly or individually; the routing can be controlled only indirectly and only as a whole by modifying the routing metric. Thus, one of the main tasks when planning such networks is to find administrative link weights that induce a globally efficient traffic routing traffic!routing configuration of an AS. It turns out that this task leads to very difficult mathematical optimization problems. In this chapter, we discuss and describe exact integer programming models and solution approaches as well as practically efficient smart heuristics for such shortest path routing problems shortest path routing!problems .

Chromatin immunoprecipitation with fixed animal tissues and preparation for high-throughput sequencing.

PubMed

Cotney, Justin L; Noonan, James P

2015-02-02

Chromatin immunoprecipitation coupled with high-throughput sequencing (ChIP-Seq) is a powerful method used to identify genome-wide binding patterns of transcription factors and distribution of various histone modifications associated with different chromatin states. In most published studies, ChIP-Seq has been performed on cultured cells grown under controlled conditions, allowing generation of large amounts of material in a homogeneous biological state. Although such studies have provided great insight into the dynamic landscapes of animal genomes, they do not allow the examination of transcription factor binding and chromatin states in adult tissues, developing embryonic structures, or tumors. Such knowledge is critical to understanding the information required to create and maintain a complex biological tissue and to identify noncoding regions of the genome directly involved in tissues affected by complex diseases such as autism. Studying these tissue types with ChIP-Seq can be challenging due to the limited availability of tissues and the lack of complex biological states able to be achieved in culture. These inherent differences require alterations of standard cross-linking and chromatin extraction typically used in cell culture. Here we describe a general approach for using small amounts of animal tissue to perform ChIP-Seq directed at histone modifications and transcription factors. Tissue is homogenized before treatment with formaldehyde to ensure proper cross-linking, and a two-step nuclear isolation is performed to increase extraction of soluble chromatin. Small amounts of soluble chromatin are then used for immunoprecipitation (IP) and prepared for multiplexed high-throughput sequencing. © 2015 Cold Spring Harbor Laboratory Press.

Global Mapping of Transcription Factor Binding Sites by Sequencing Chromatin Surrogates: a Perspective on Experimental Design, Data Analysis, and Open Problems.

PubMed

Wei, Yingying; Wu, George; Ji, Hongkai

2013-05-01

Mapping genome-wide binding sites of all transcription factors (TFs) in all biological contexts is a critical step toward understanding gene regulation. The state-of-the-art technologies for mapping transcription factor binding sites (TFBSs) couple chromatin immunoprecipitation (ChIP) with high-throughput sequencing (ChIP-seq) or tiling array hybridization (ChIP-chip). These technologies have limitations: they are low-throughput with respect to surveying many TFs. Recent advances in genome-wide chromatin profiling, including development of technologies such as DNase-seq, FAIRE-seq and ChIP-seq for histone modifications, make it possible to predict in vivo TFBSs by analyzing chromatin features at computationally determined DNA motif sites. This promising new approach may allow researchers to monitor the genome-wide binding sites of many TFs simultaneously. In this article, we discuss various experimental design and data analysis issues that arise when applying this approach. Through a systematic analysis of the data from the Encyclopedia Of DNA Elements (ENCODE) project, we compare the predictive power of individual and combinations of chromatin marks using supervised and unsupervised learning methods, and evaluate the value of integrating information from public ChIP and gene expression data. We also highlight the challenges and opportunities for developing novel analytical methods, such as resolving the one-motif-multiple-TF ambiguity and distinguishing functional and non-functional TF binding targets from the predicted binding sites. The online version of this article (doi:10.1007/s12561-012-9066-5) contains supplementary material, which is available to authorized users.

Proteomics to study DNA-bound and chromatin-associated gene regulatory complexes

PubMed Central

Wierer, Michael; Mann, Matthias

2016-01-01

High-resolution mass spectrometry (MS)-based proteomics is a powerful method for the identification of soluble protein complexes and large-scale affinity purification screens can decode entire protein interaction networks. In contrast, protein complexes residing on chromatin have been much more challenging, because they are difficult to purify and often of very low abundance. However, this is changing due to recent methodological and technological advances in proteomics. Proteins interacting with chromatin marks can directly be identified by pulldowns with synthesized histone tails containing posttranslational modifications (PTMs). Similarly, pulldowns with DNA baits harbouring single nucleotide polymorphisms or DNA modifications reveal the impact of those DNA alterations on the recruitment of transcription factors. Accurate quantitation – either isotope-based or label free – unambiguously pinpoints proteins that are significantly enriched over control pulldowns. In addition, protocols that combine classical chromatin immunoprecipitation (ChIP) methods with mass spectrometry (ChIP-MS) target gene regulatory complexes in their in-vivo context. Similar to classical ChIP, cells are crosslinked with formaldehyde and chromatin sheared by sonication or nuclease digested. ChIP-MS baits can be proteins in tagged or endogenous form, histone PTMs, or lncRNAs. Locus-specific ChIP-MS methods would allow direct purification of a single genomic locus and the proteins associated with it. There, loci can be targeted either by artificial DNA-binding sites and corresponding binding proteins or via proteins with sequence specificity such as TAL or nuclease deficient Cas9 in combination with a specific guide RNA. We predict that advances in MS technology will soon make such approaches generally applicable tools in epigenetics. PMID:27402878

Amplitude of the Lidov-Kozai I and e oscillations in asteroid families

NASA Astrophysics Data System (ADS)

Vinogradova, T. A.

2017-07-01

Asteroid families were used to study secular perturbations induced by the Lidov-Kozai mechanism (LKM). The LKM represents coupled long-period oscillations of the inclination I and the eccentricity e. These oscillations depend on the argument of the perihelion ω and become substantial for high inclinations and large eccentricities. After excluding classical secular perturbations, the LKM oscillations of the elements became visible very clearly in the distributions of orbital elements (sin I, ω) and (e, ω). These oscillations can be approximated by the functions Asin Isin (2ω + 90°) and Aesin (2ω - 90°), respectively, and the amplitudes of the oscillations Asin I and Ae can be easily obtained by the least-squares method. By excluding the LKM oscillations, we can calculate the proper elements Ip and ep. Asteroid families that have different proper inclinations and eccentricities were used to study the amplitudes of the LKM I and e oscillations. As a result, it was found that the net amplitude A = √{A_{sin I}^2+A_e^2} increases with increasing Ip and ep and can be approximated by a power law of the product epsin Ip. If the amplitude A is known, the amplitudes of the e and I oscillations can be calculated as Ae = Acos α and Asin I = Asin α, where tan α = -e_p(1-sin ^2 i_p)/sin i_p(1-e_p^2). It follows that the relationship between the amplitudes is approximately described as Asin I/Ae ≈ ep/sin Ip.

Overview of Non-Solenoidal Startup Studies in the Pegasus ST

NASA Astrophysics Data System (ADS)

Bongard, M. W.; Barr, J. L.; Bodner, G. M.; Burke, M. G.; Fonck, R. J.; Pachicano, J. L.; Perry, J. M.; Reusch, J. A.; Richner, N. J.; Rodriguez Sanchez, C.; Schlossberg, D. J.

2016-10-01

Local helicity injection (LHI) is a non-solenoidal startup method pursued on Pegasus utilizing compact, high power current sources (Ainj 2 - 4 cm2, Iinj 10 kA, Vinj 1 kV) at the plasma edge. Outboard injectors (Ninj = 4 , Ainj = 8 cm2) produce Ip 170 kA plasmas compatible with Ohmic drive. A 0-D model that treats the plasma as a resistive element with time-varying inductance and enforces Ip limits from Taylor relaxation is used to interpret experimental Ip(t) in several scenarios. Strong inductive drive arises from the plasma shape evolution, in addition to poloidal field induction. A new injector system has recently been installed in the lower divertor region (Ninj = 2 , Ainj = 8 cm2) to explore the implications of geometric placement of the helicity injectors on LHI startup. This geometry supports tests of reconnection dynamics seen in NIMROD simulations, high-BT effects expected in larger devices, and LHI electron confinement with and without inductive assist. Plasmas with Ip > 130 kA, Vinj 0.5 kV, Δtpulse 8 ms and BT /BT , max <= 50 % are produced with the inboard system to date, consistent with performance expectations. Higher Ip is expected with increased BT, Vinj, and Δtpulse . Thomson scattering data in both geometries indicate high Te >= 100 eV during LHI, suggesting the confinement is not strongly stochastic. Conceptual design work is exploring the feasibility of coaxial helicity injection and ECH heating on Pegasus in addition to LHI. Work supported by US DOE Grant DE-FG02-96ER54375.

40 CFR 1051.140 - What is my vehicle's maximum engine power and displacement?

Code of Federal Regulations, 2012 CFR

2012-07-01

... power and displacement? 1051.140 Section 1051.140 Protection of Environment ENVIRONMENTAL PROTECTION... displacement? This section describes how to quantify your vehicle's maximum engine power and displacement for... available engine torque with engine speed. (b) An engine configuration's displacement is the intended swept...

40 CFR 1051.140 - What is my vehicle's maximum engine power and displacement?

Code of Federal Regulations, 2013 CFR

2013-07-01

... power and displacement? 1051.140 Section 1051.140 Protection of Environment ENVIRONMENTAL PROTECTION... displacement? This section describes how to quantify your vehicle's maximum engine power and displacement for... available engine torque with engine speed. (b) An engine configuration's displacement is the intended swept...

40 CFR 1051.140 - What is my vehicle's maximum engine power and displacement?

Code of Federal Regulations, 2010 CFR

2010-07-01

... power and displacement? 1051.140 Section 1051.140 Protection of Environment ENVIRONMENTAL PROTECTION... displacement? This section describes how to quantify your vehicle's maximum engine power and displacement for... available engine torque with engine speed. (b) An engine configuration's displacement is the intended swept...

40 CFR 1051.140 - What is my vehicle's maximum engine power and displacement?

Code of Federal Regulations, 2014 CFR

2014-07-01

... power and displacement? 1051.140 Section 1051.140 Protection of Environment ENVIRONMENTAL PROTECTION... displacement? This section describes how to quantify your vehicle's maximum engine power and displacement for... available engine torque with engine speed. (b) An engine configuration's displacement is the intended swept...

40 CFR 1051.140 - What is my vehicle's maximum engine power and displacement?

Code of Federal Regulations, 2011 CFR

2011-07-01

... power and displacement? 1051.140 Section 1051.140 Protection of Environment ENVIRONMENTAL PROTECTION... displacement? This section describes how to quantify your vehicle's maximum engine power and displacement for... available engine torque with engine speed. (b) An engine configuration's displacement is the intended swept...

A comparison of the effects on central 5-HT function of sibutramine hydrochloride and other weight-modifying agents

PubMed Central

Heal, D J; Cheetham, S C; Prow, M R; Martin, K F; Buckett, W R

1998-01-01

Effects on 5-HT function of sibutramine and its active metabolites, BTS 54 354 and BTS 54 505, were compared with fluoxetine, (+)-fenfluramine and (+)-amphetamine.In vitro sibutramine weakly inhibited [3H]-5-HT uptake into brain synaptosomes. BTS 54 354, BTS 54 505 and fluoxetine were powerful [3H]-5-HT uptake inhibitors, whereas (+)-fenfluramine and (+)-amphetamine were very much weaker. Conversely, whilst sibutramine, its metabolites and fluoxetine did not release [3H]-5-HT from brain slices at ⩽10−5M, (+)-fenfluramine and (+)-amphetamine concentration-dependently increased [3H]-5-HT release.Sibutramine and fluoxetine had no effect on 5-hydroxytryptophan (5-HTP) accumulation in either frontal cortex or hypothalamus at doses <10 mg kg−1. In contrast, (+)-amphetamine (⩾3 mg kg−1) reduced 5-HTP in hypothalamus, whilst (+)-fenfluramine (⩾1 mg kg−1) decreased 5-HTP in both regions.Sibutramine (10 mg kg−1 i.p.) and fluoxetine (10 mg kg−1 i.p.) produced slow, prolonged increases of extracellular 5-HT in the anterior hypothalamus. In contrast, (+)-fenfluramine (3 mg kg−1 i.p.) and (+)-amphetamine (4 mg kg−1 i.p.) induced rapid, short-lasting increases in extracellular 5-HT.Only (+)-fenfluramine (10 mg kg−1) altered 5-HT2A receptors in rat frontal cortex when given for 14 days, producing a 61% reduction in receptor number and a 18% decrease in radioligand affinity.These results show that sibutramine powerfully enhances central 5-HT function via its secondary and primary amine metabolites; this effect, like that of fluoxetine, is almost certainly mediated through 5-HT uptake inhibition. By contrast, (+)-fenfluramine enhances 5-HT function predominantly by increasing 5-HT release. (+)-Amphetamine, though weaker than (+)-fenfluramine, also enhances 5-HT function by release. PMID:9786502

QCSEE UTW engine powered-lift acoustic performance. [Quiet Clean Short-haul Experimental Engine Under The Wing

NASA Technical Reports Server (NTRS)

Loeffler, I. J.; Samanich, N. E.; Bloomer, H. E.

1980-01-01

Powered-lift acoustic tests of a quiet clean short-haul experimental engine (QCSEE) under-the-wing (UTW) engine are described. Engine and wing configurations are outlined, along with instrumentation and test facilities. The results of these tests are reported. In addition, the UTW engine powered-lift performance is compared with that of the previously tested QCSEE over-the-wing (OTW) engine.

Evaluation of PM emissions from two in-service gas turbine general aviation aircraft engines

NASA Astrophysics Data System (ADS)

Yu, Zhenhong; Liscinsky, David S.; Fortner, Edward C.; Yacovitch, Tara I.; Croteau, Philip; Herndon, Scott C.; Miake-Lye, Richard C.

2017-07-01

We determined particulate matter (PM) emissions in the exhaust plumes from two gas turbine aircraft engines: a CF34-3A1 turbofan engine and a TPE331-6-252B turboprop engine in a dedicated study on in-service general aviation aircraft. The engine power states were from 16% to 100% engine thrust. Both nucleation and soot mode particles were observed from the emission exhausts of the CF34-3A1 engine but only soot particle mode was detected from the TPE331-6-252B engine. For the CF34-3A1 engine, the contribution of soot mode to total PM emissions was dominant at high power, while at decreased engine power states nucleation mode organic PM became important. PM emissions indices of the TPE331-6-252B engine were found to be generally larger than those of the CF34-3A1 engine. For both engines, medium power conditions (40-60% of thrust) yielded the lowest PM emissions. For the TPE331-6-252B engine, volatile PM components including organic and sulfate were more than 50% in mass at low power, while non-volatile black carbon became dominant at high power conditions such as takeoff.

Overview of NASA Lewis Research Center free-piston Stirling engine technology activities applicable to space power systems

NASA Technical Reports Server (NTRS)

Slaby, Jack G.

1987-01-01

A brief overview is presented of the development and technological activities of the free-piston Stirling engine. The engine started as a small scale fractional horsepower engine which demonstrated basic engine operating principles and the advantages of being hermetically sealed, highly efficient, and simple. It eventually developed into the free piston Stirling engine driven heat pump, and then into the SP-100 Space Reactor Power Program from which came the Space Power Demonstrator Engine (SPDE). The SPDE successfully operated for over 300 hr and delivered 20 kW of PV power to an alternator plunger. The SPDE demonstrated that a dynamic power conversion system can, with proper design, be balanced; and the engine performed well with externally pumped hydrostatic gas bearings.

Research Study Towards a MEFFV Electric Armament System

DTIC Science & Technology

2004-01-01

CHPSPerf Inputs Parameter Setting Engine Power (kW) 500 per engine Generator Power (kW) 500/generator Traction Motors Power (kW) 500/side # Battery Pack...Cells in Parallel 2 # Motors in Drive Train 2 Max Power of Traction Motors 200 Minimum Engine Power (kW) 50 Optimum Engine Power (kW) 750 Stop... motors . Other options were examined for the energy storage system. Of particular interest in this regard is the use of the CPA flywheel as the load

76 FR 22729 - Chrysler Group, LLC, Power Train Division, Mack Avenue Engine Plant #1, Including On-Site Leased...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-22

..., Power Train Division, Mack Avenue Engine Plant 1, Including On-Site Leased Workers From Caravan Knight..., applicable to workers of Chrysler Group, LLC, Power Train Division, Mack Avenue Engine Plant 1, including on... all workers of Chrysler LLC, Mack Avenue Engine Plants 1 & 2, Power Train Division, Detroit, Michigan...

14 CFR 121.645 - Fuel supply: Turbine-engine powered airplanes, other than turbo propeller: Flag and supplemental...

Code of Federal Regulations, 2010 CFR

2010-01-01

... specifications, no person may release for flight or takeoff a turbine-engine powered airplane (other than a turbo... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Fuel supply: Turbine-engine powered... SUPPLEMENTAL OPERATIONS Dispatching and Flight Release Rules § 121.645 Fuel supply: Turbine-engine powered...

14 CFR 121.645 - Fuel supply: Turbine-engine powered airplanes, other than turbo propeller: Flag and supplemental...

Code of Federal Regulations, 2011 CFR

2011-01-01

... specifications, no person may release for flight or takeoff a turbine-engine powered airplane (other than a turbo... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Fuel supply: Turbine-engine powered... SUPPLEMENTAL OPERATIONS Dispatching and Flight Release Rules § 121.645 Fuel supply: Turbine-engine powered...

Induced Polarization Surveying for Acid Rock Screening in Highway Design

NASA Astrophysics Data System (ADS)

Butler, K. E.; Al, T.; Bishop, T.

2004-05-01

Highway and pipeline construction agencies have become increasingly vigilant in their efforts to avoid cutting through sulphide-bearing bedrock that has potential to produce acid rock drainage. Blasting and fragmentation of such rock increases the surface area available for sulphide oxidation and hence increases the risk of acid rock drainage unless the rock contains enough natural buffering capacity to neutralize the pH. In December, 2001, the New Brunswick Department of Transportation (NBOT) sponsored a field trial of geophysical surveying in order to assess its suitability as a screening tool for locating near-surface sulphides along proposed highway alignments. The goal was to develop a protocol that would allow existing programs of drilling and geochemical testing to be targeted more effectively, and provide design engineers with the information needed to reduce rock cuts where necessary and dispose of blasted material in a responsible fashion. Induced polarization (IP) was chosen as the primary geophysical method given its ability to detect low-grade disseminated mineralization. The survey was conducted in dipole-dipole mode using an exploration-style time domain IP system, dipoles 8 to 25 m in length, and six potential dipoles for each current dipole location (i.e. n = 1 - 6). Supplementary information was provided by resistivity and VLF-EM surveys sensitive to lateral changes in electrical conductivity, and by magnetic field surveying chosen for its sensitivity to the magnetic susceptibility of pyrrhotite. Geological and geochemical analyses of samples taken from several IP anomalies located along 4.3 line-km of proposed highway confirmed the effectiveness of the screening technique. IP pseudosections from a region of metamorphosed shales and volcaniclastic rocks identified discrete, well-defined mineralized zones. Stronger, overlapping, and more laterally extensive IP anomalies were observed over a section of graphitic and sulphide-bearing metasedimentary rocks. Attempts to use spectral IP characteristics to determine relative abundances of sulphides and graphite were not conclusive. The overall effectiveness of the screening technique however encouraged NBDOT to apply it to an additional 50 km of planned rock cuts along the corridor selected for the new Trans-Canada Highway.

14 CFR 135.381 - Large transport category airplanes: Turbine engine powered: En route limitations: One engine...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Large transport category airplanes: Turbine... Limitations § 135.381 Large transport category airplanes: Turbine engine powered: En route limitations: One engine inoperative. (a) No person operating a turbine engine powered large transport category airplane...

14 CFR 135.381 - Large transport category airplanes: Turbine engine powered: En route limitations: One engine...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Large transport category airplanes: Turbine... Limitations § 135.381 Large transport category airplanes: Turbine engine powered: En route limitations: One engine inoperative. (a) No person operating a turbine engine powered large transport category airplane...

14 CFR 135.381 - Large transport category airplanes: Turbine engine powered: En route limitations: One engine...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Large transport category airplanes: Turbine... Limitations § 135.381 Large transport category airplanes: Turbine engine powered: En route limitations: One engine inoperative. (a) No person operating a turbine engine powered large transport category airplane...

14 CFR 135.381 - Large transport category airplanes: Turbine engine powered: En route limitations: One engine...

Code of Federal Regulations, 2011 CFR

2011-01-01

... Limitations § 135.381 Large transport category airplanes: Turbine engine powered: En route limitations: One engine inoperative. (a) No person operating a turbine engine powered large transport category airplane... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Large transport category airplanes: Turbine...

14 CFR 121.193 - Airplanes: Turbine engine powered: En route limitations: Two engines inoperative.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Turbine engine powered: En route limitations: Two engines inoperative. 121.193 Section 121.193 Aeronautics and Space FEDERAL AVIATION... Performance Operating Limitations § 121.193 Airplanes: Turbine engine powered: En route limitations: Two...

14 CFR 121.191 - Airplanes: Turbine engine powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Turbine engine powered: En route limitations: One engine inoperative. 121.191 Section 121.191 Aeronautics and Space FEDERAL AVIATION... Performance Operating Limitations § 121.191 Airplanes: Turbine engine powered: En route limitations: One...

14 CFR 121.191 - Airplanes: Turbine engine powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Turbine engine powered: En route limitations: One engine inoperative. 121.191 Section 121.191 Aeronautics and Space FEDERAL AVIATION... Performance Operating Limitations § 121.191 Airplanes: Turbine engine powered: En route limitations: One...

14 CFR 121.193 - Airplanes: Turbine engine powered: En route limitations: Two engines inoperative.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Turbine engine powered: En route limitations: Two engines inoperative. 121.193 Section 121.193 Aeronautics and Space FEDERAL AVIATION... Performance Operating Limitations § 121.193 Airplanes: Turbine engine powered: En route limitations: Two...

14 CFR 135.381 - Large transport category airplanes: Turbine engine powered: En route limitations: One engine...

Code of Federal Regulations, 2010 CFR

2010-01-01

... Limitations § 135.381 Large transport category airplanes: Turbine engine powered: En route limitations: One engine inoperative. (a) No person operating a turbine engine powered large transport category airplane... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Large transport category airplanes: Turbine...

Integrated engine-generator concept for aircraft electric secondary power

NASA Technical Reports Server (NTRS)

Secunde, R. R.; Macosko, R. P.; Repas, D. S.

1972-01-01

The integrated engine-generator concept of locating an electric generator inside an aircraft turbojet or turbofan engine concentric with, and driven by, one of the main engine shafts is discussed. When properly rated, the generator can serve as an engine starter as well as a generator of electric power. The electric power conversion equipment and generator controls are conveniently located in the aircraft. Preliminary layouts of generators in a large engine together with their physical sizes and weights indicate that this concept is a technically feasible approach to aircraft secondary power.

Integrated engine generator for aircraft secondary power

NASA Technical Reports Server (NTRS)

Secunde, R. R.

1972-01-01

An integrated engine-generator for aircraft secondary power generation is described. The concept consists of an electric generator located inside a turbojet or turbofan engine and both concentric with and driven by one of the main engine shafts. The electric power conversion equipment and generator controls are located in the aircraft. When properly rated, the generator serves as an engine starter as well as a source of electric power. This configuration reduces or eliminates the need for an external gear box on the engine and permits reduction in the nacelle diameter.

Hybrid Engine Powered City Car: Fuzzy Controlled Approach

NASA Astrophysics Data System (ADS)

Rahman, Ataur; Mohiuddin, AKM; Hawlader, MNA; Ihsan, Sany

2017-03-01

This study describes a fuzzy controlled hybrid engine powered car. The car is powered by the lithium ion battery capacity of 1000 Wh is charged by the 50 cc hybrid engine and power regenerative mode. The engine is operated with lean mixture at 3000 rpm to charge the battery. The regenerative mode that connects with the engine generates electrical power of 500-600 W for the deceleration of car from 90 km/h to 20 km/h. The regenerated electrical power has been used to power the air-conditioning system and to meet the other electrical power. The battery power only used to propel the car. The regenerative power also found charging the battery for longer operation about 40 minutes and more. The design flexibility of this vehicle starts with whole-vehicle integration based on radical light weighting, drag reduction, and accessory efficiency. The energy efficient hybrid engine cut carbon dioxide (CO2) and nitrogen oxides (N2O) emission about 70-80% as the loads on the crankshaft such as cam-follower and its associated rotating components are replaced by electromagnetic systems, and the flywheel, alternator and starter motor are replaced by a motor generator. The vehicle was tested and found that it was able to travel 70 km/litre with the power of hybrid engine.

49 CFR 173.427 - Transport requirements for low specific activity (LSA) Class 7 (radioactive) materials and...

Code of Federal Regulations, 2010 CFR

2010-10-01

... package (IP-1, IP-2 or IP-3; § 173.411), subject to the limitations of Table 6; (2) In a DOT Specification... use shipment 1. LSA-I: Solid IP-1 IP-1 Liquid IP-1 IP-2 2. LSA-II: Solid IP-2 IP-2 Liquid and gas IP-2 IP-3 3. LSA-III IP-2 IP-3 4. SCO-I IP-1 IP-1 5. SCO-II IP-2 IP-2 [69 FR 3676, Jan. 26, 2004; 69 FR...

49 CFR 173.427 - Transport requirements for low specific activity (LSA) Class 7 (radioactive) materials and...

Code of Federal Regulations, 2011 CFR

2011-10-01

... package (IP-1, IP-2 or IP-3; § 173.411), subject to the limitations of Table 6; (2) In a DOT Specification... use shipment 1. LSA-I: Solid IP-1 IP-1 Liquid IP-1 IP-2 2. LSA-II: Solid IP-2 IP-2 Liquid and gas IP-2 IP-3 3. LSA-III IP-2 IP-3 4. SCO-I IP-1 IP-1 5. SCO-II IP-2 IP-2 [69 FR 3676, Jan. 26, 2004; 69 FR...

Using VoIP to compete.

PubMed

Werbach, Kevin

2005-09-01

Internet telephony, or VoIP, is rapidly replacing the conventional kind. This year, for the first time, U.S. companies bought more new Internet-phone connections than standard lines. The major driver behind this change is cost. But VoIP isn't just a new technology for making old-fashioned calls cheaper, says consultant Kevin Werbach. It is fundamentally changing how companies use voice communications. What makes VoIP so powerful is that it turns voice into digital data packets that can be stored, copied, combined with other data, and distributed to virtually any device that connects to the Internet. And it makes it simple to provide all the functionality of a corporate phone-call features, directories, security-to anyone anywhere there's broadband access. That fosters new kinds of businesses such as virtual call centers, where widely dispersed agents work at all hours from their homes. The most successful early adopters, says Werbach, will focus more on achieving business objectives than on saving money. They will also consider how to push VoIP capabilities out to the extended organization, making use of everyone as a resource. Deployment may be incremental, but companies should be thinking about where VoIP could take them. Executives should ask what they could do if, on demand, they could bring all their employees, customers, suppliers, and partners together in a virtual room, with shared access to every modern communications and computing channel. They should take a fresh look at their business processes to find points at which richer and more customizable communications could eliminate bottlenecks and enhance quality. The important dividing line won't be between those who deploy Vol P and those who don't, or even between early adopters and laggards. It will be between those who see Vol P as just a new way to do the same old things and those who use itto rethink their entire businesses.

Accelerated generation of human induced pluripotent stem cells with retroviral transduction and chemical inhibitors under physiological hypoxia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shimada, Hidenori; Hashimoto, Yoshiya; Nakada, Akira

2012-01-13

Highlights: Black-Right-Pointing-Pointer Very rapid generation of human iPS cells under optimized conditions. Black-Right-Pointing-Pointer Five chemical inhibitors under hypoxia boosted reprogramming. Black-Right-Pointing-Pointer We performed genome-wide DNA methylation analysis. -- Abstract: Induced pluripotent stem (iPS) cells are generated from somatic cells by the forced expression of a defined set of pluripotency-associated transcription factors. Human iPS cells can be propagated indefinitely, while maintaining the capacity to differentiate into all cell types in the body except for extra-embryonic tissues. This technology not only represents a new way to use individual-specific stem cells for regenerative medicine but also constitutes a novel method to obtain largemore » amounts of disease-specific cells for biomedical research. Despite their great potential, the long reprogramming process (up to 1 month) remains one of the most significant challenges facing standard virus-mediated methodology. In this study, we report the accelerated generation of human iPS cells from adipose-derived stem (ADS) cells, using a new combination of chemical inhibitors under a setting of physiological hypoxia in conjunction with retroviral transduction of Oct4, Sox2, Klf4, and L-Myc. Under optimized conditions, we observed human embryonic stem (ES)-like cells as early as 6 days after the initial retroviral transduction. This was followed by the emergence of fully reprogrammed cells bearing Tra-1-81-positive and DsRed transgene-silencing properties on day 10. The resulting cell lines resembled human ES cells in many respects including proliferation rate, morphology, pluripotency-associated markers, global gene expression patterns, genome-wide DNA methylation states, and the ability to differentiate into all three of the germ layers, both in vitro and in vivo. Our method, when combined with chemical inhibitors under conditions of physiological hypoxia, offers a powerful tool for rapidly generating bona fide human iPS cells and facilitates the application of iPS cell technology to biomedical research.« less

Experimental Evaluation of a Method for Turbocharging Four-Stroke, Single Cylinder, Internal Combustion Engines

NASA Astrophysics Data System (ADS)

Buchman, Michael; Winter, Amos

2015-11-01

Turbocharging an engine increases specific power, improves fuel economy, reduces emissions, and lowers cost compared to a naturally aspirated engine of the same power output. These advantages make turbocharging commonplace for multi-cylinder engines. Single cylinder engineers are not commonly turbocharged due to the phase lag between the exhaust stroke, which powers the turbocharger, and the intake stroke, when air is pumped into the engine. Our proposed method of turbocharging single cylinder engines is to add an ``air capacitor'' to the intake manifold, an additional volume that acts as a buffer to store compressed air between the exhaust and intake strokes, and smooth out the pressure pulses from the turbocharger. This talk presents experimental results from a single cylinder, turbocharged diesel engine fit with various sized air capacitors. Power output from the engine was measured using a dynamometer made from a generator, with the electrical power dissipated with resistive heating elements. We found that intake air density increases with capacitor size as theoretically predicted, ranging from 40 to 60 percent depending on heat transfer. Our experiment was able to produce 29 percent more power compared to using natural aspiration. These results validated that an air capacitor and turbocharger may be a simple, cost effective means of increasing the power density of single cylinder engines.

Saturation analysis of ChIP-seq data for reproducible identification of binding peaks

PubMed Central

Hansen, Peter; Hecht, Jochen; Ibrahim, Daniel M.; Krannich, Alexander; Truss, Matthias; Robinson, Peter N.

2015-01-01

Chromatin immunoprecipitation coupled with next-generation sequencing (ChIP-seq) is a powerful technology to identify the genome-wide locations of transcription factors and other DNA binding proteins. Computational ChIP-seq peak calling infers the location of protein–DNA interactions based on various measures of enrichment of sequence reads. In this work, we introduce an algorithm, Q, that uses an assessment of the quadratic enrichment of reads to center candidate peaks followed by statistical analysis of saturation of candidate peaks by 5′ ends of reads. We show that our method not only is substantially faster than several competing methods but also demonstrates statistically significant advantages with respect to reproducibility of results and in its ability to identify peaks with reproducible binding site motifs. We show that Q has superior performance in the delineation of double RNAPII and H3K4me3 peaks surrounding transcription start sites related to a better ability to resolve individual peaks. The method is implemented in C+l+ and is freely available under an open source license. PMID:26163319

Technical note on results of production test IP-628-AI: Crosstie flow test and flushing calibration, and the earlier production tests IP-573-AI and IP-499-AI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, S.S.

1964-06-15

A series of three experimental tests was conducted on the operation and adequacy of the K-Reactors` third, or last-ditch, cooling system. The first test showed considerable line corrosion the second test was performed directly after line cleaning, and the third test showed a significant amount of additional line corrosion after only nine months of service. The present cooling adequacy of this last-ditch system at the KE and KW reactors is summarized these show the power levels for which we have adequate last-ditch cooling as a function of the crosstie coolant temperature. These figures include the effects of increasing the numbermore » of pumps that remain in operation at the other K-Reactor, and various other operating or emergency conditions. These curves are for diesel pump speeds of 750 rpm which are planned for June of this year. In these figures the crosstie temperature is assumed to be a conservative 5{degrees}C above the process water inlet temperature.« less

Heat engine development for solar thermal power systems

NASA Astrophysics Data System (ADS)

Pham, H. Q.; Jaffe, L. D.

The parabolic dish solar collector systems for converting sunlight to electrical power through a heat engine will, require a small heat engine of high performance long lifetime to be competitive with conventional power systems. The most promising engine candidates are Stirling, high temperature Brayton, and combined cycle. Engines available in the current market today do not meet these requirements. The development of Stirling and high temperature Brayton for automotive applications was studied which utilizes much of the technology developed in this automotive program for solar power engines. The technical status of the engine candidates is reviewed and the components that may additional development to meet solar thermal system requirements are identified.

VoIP attacks detection engine based on neural network

NASA Astrophysics Data System (ADS)

Safarik, Jakub; Slachta, Jiri

2015-05-01

The security is crucial for any system nowadays, especially communications. One of the most successful protocols in the field of communication over IP networks is Session Initiation Protocol. It is an open-source project used by different kinds of applications, both open-source and proprietary. High penetration and text-based principle made SIP number one target in IP telephony infrastructure, so security of SIP server is essential. To keep up with hackers and to detect potential malicious attacks, security administrator needs to monitor and evaluate SIP traffic in the network. But monitoring and following evaluation could easily overwhelm the security administrator in networks, typically in networks with a number of SIP servers, users and logically or geographically separated networks. The proposed solution lies in automatic attack detection systems. The article covers detection of VoIP attacks through a distributed network of nodes. Then the gathered data analyze aggregation server with artificial neural network. Artificial neural network means multilayer perceptron network trained with a set of collected attacks. Attack data could also be preprocessed and verified with a self-organizing map. The source data is detected by distributed network of detection nodes. Each node contains a honeypot application and traffic monitoring mechanism. Aggregation of data from each node creates an input for neural networks. The automatic classification on a centralized server with low false positive detection reduce the cost of attack detection resources. The detection system uses modular design for easy deployment in final infrastructure. The centralized server collects and process detected traffic. It also maintains all detection nodes.

Ecologically and economically conscious design of the injected pultrusion process via multi-objective optimization

NASA Astrophysics Data System (ADS)

Srinivasagupta, Deepak; Kardos, John L.

2004-05-01

Injected pultrusion (IP) is an environmentally benign continuous process for low-cost manufacture of prismatic polymer composites. IP has been of recent regulatory interest as an option to achieve significant vapour emissions reduction. This work describes the design of the IP process with multiple design objectives. In our previous work (Srinivasagupta D et al 2003 J. Compos. Mater. at press), an algorithm for economic design using a validated three-dimensional physical model of the IP process was developed, subject to controllability considerations. In this work, this algorithm was used in a multi-objective optimization approach to simultaneously meet economic, quality related, and environmental objectives. The retrofit design of a bench-scale set-up was considered, and the concept of exergy loss in the process, as well as in vapour emission, was introduced. The multi-objective approach was able to determine the optimal values of the processing parameters such as heating zone temperatures and resin injection pressure, as well as the equipment specifications (die dimensions, heater, puller and pump ratings) that satisfy the various objectives in a weighted sense, and result in enhanced throughput rates. The economic objective did not coincide with the environmental objective, and a compromise became necessary. It was seen that most of the exergy loss is in the conversion of electric power into process heating. Vapour exergy loss was observed to be negligible for the most part.

Dependence of SOL widths on plasma parameters in NSTX

NASA Astrophysics Data System (ADS)

Ahn, Joon-Wook; Maingi, Rajesh; Boedo, Jose; Soukhanovskii, Vlad; Leblanc, Ben; Kaita, Robert

2008-11-01

The dependence of various upstream Scrape-Off Layer (SOL) widths on the line-averaged density (n e), plasma current (Ip), and power into the SOL (PSOL) for H-mode plasmas was investigated, using the mid-plane fast reciprocating probe and Thomson scattering diagnostics, in the National Spherical Torus Experiment (NSTX). The heat flux width (λq) at the divertor plate, measured by the IR camera, was also measured and compared with the upstream SOL widths. The edge density profile remains fixed during the H-mode, such that the separatrix density is constant even though n e is ramping. Thus λq, λTe, and λne are insensitive to n e. λTe and λjsat have strong negative dependence on Ip, whereas there was only a very weak change in λne when Ip was varied. These empirical results have been compared with scaling laws in the literature. The λTe dependence on Ip is consistent with an H-mode λTe scaling law, while the insensitivity of λne to n e is not consistent with the λne scaling law. Dependence of decay lengths on plasma parameters in a wide range of plasma conditions will be presented. This work was supported by the US Department of Energy, contract numbers DE-FG02-03ER54731, DE-AC02-76CH03073, DE-AC05-00OR22725, and DE-AC52-07NA27344.

Improving Power Density of Free-Piston Stirling Engines

NASA Technical Reports Server (NTRS)

Briggs, Maxwell H.; Prahl, Joseph M.; Loparo, Kenneth A.

2016-01-01

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free-piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58 percent using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a piston power increase of as much as 14 percent. Analytical predictions are compared to experimental data and show close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

Improving Power Density of Free-Piston Stirling Engines

NASA Technical Reports Server (NTRS)

Briggs, Maxwell H.; Prahl, Joseph; Loparo, Kenneth

2016-01-01

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58 using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a maximum piston power increase of 14. Analytical predictions are compared to experimental data showing close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

Improving Free-Piston Stirling Engine Power Density

NASA Technical Reports Server (NTRS)

Briggs, Maxwell H.

2016-01-01

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58% using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a maximum piston power increase of 14%. Analytical predictions are compared to experimental data showing close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

Decay of Solar Wind Turbulence behind Interplanetary Shocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pitňa, Alexander; Šafránková, Jana; Němeček, Zdeněk

We investigate the decay of magnetic and kinetic energies behind IP shocks with motivation to find a relaxation time when downstream turbulence reaches a usual solar wind value. We start with a case study that introduces computation techniques and quantifies a contribution of kinetic fluctuations to the general energy balance. This part of the study is based on high-time (31 ms) resolution plasma data provided by the Spektr-R spacecraft. On the other hand, a statistical part is based on 92 s Wind plasma and magnetic data and its results confirm theoretically established decay laws for kinetic and magnetic energies. Wemore » observe the power-law behavior of the energy decay profiles and we estimated the power-law exponents of both kinetic and magnetic energy decay rates as −1.2. We found that the decay of MHD turbulence does not start immediately after the IP shock ramp and we suggest that the proper decay of turbulence begins when a contribution of the kinetic processes becomes negligible. We support this suggestion with a detailed analysis of the decay of turbulence at the kinetic scale.« less

49 CFR 173.220 - Internal combustion engines, self-propelled vehicles, mechanical equipment containing internal...

Code of Federal Regulations, 2010 CFR

2010-10-01

... vehicles, mechanical equipment containing internal combustion engines, and battery powered vehicles or... equipment containing internal combustion engines, and battery powered vehicles or equipment. (a... internal combustion engine, or a battery powered vehicle or equipment is subject to the requirements of...

An ethnomethodological approach to examine exploitation in the context of capacity, trust and experience of commercial surrogacy in India.

PubMed

Saravanan, Sheela

2013-08-20

The socio-ethical concerns regarding exploitation in commercial surrogacy are premised on asymmetric vulnerability and the commercialization of women's reproductive capacity to suit individualistic motives. In examining the exploitation argument, this article reviews the social contract theory that describes an individual as an 'economic man' with moral and/or political motivations to satisfy individual desires. This study considers the critique by feminists, who argue that patriarchal and medical control prevails in the surrogacy contracts. It also explores the exploitative dynamics amongst actors in the light of Baier's conceptualization of trust and human relationship, within which both justice and exploitation thrive, and Foucault's concept of bio-power. Drawing on these concepts, this paper aims to investigate the manifestations of exploitation in commercial surrogacy in the context of trust, power and experiences of actors, using a case study of one clinic in India. The actors' experiences are evaluated at different stages of the surrogacy process: recruitment, medical procedures, living in the surrogate home, bonding with the child and amongst actors, financial dealings, relinquishment and post-relinquishment.This study applies ethnomethodology to identify phenomena as perceived by the actors in a situation, giving importance to their interpretations of the rules that make collective activity possible. The methods include semi-structured interviews, discussions, participant observation and explanation of the phenomena from the actors' perspectives. Between August 2009 and April 2010, 13 surrogate mothers (SMs), 4 intended parents (IPs) and 2 medical practitioners (MPs) from one clinic in Western India were interviewed.This study reveals that asymmetries of capacity amongst the MPs, SMs, IPs and surrogate agents (SAs) lead to a network of trust and designation of powers through rules, bringing out the relevance of Baier's conceptualization of asymmetric vulnerability, trust and potential exploitation in human relationships. The IPs are exploited, especially in monetary terms. The SMs are relatively the most exploited, given their vulnerability. Their remuneration through surrogacy is significant for them, and their acquired knowledge as ex-surrogates is used for their own benefit and for exploiting others. Foucault's conceptualization of power is hence relevant, since the ex-SMs re-invest the power of their exploitative experience in exploiting others.

An ethnomethodological approach to examine exploitation in the context of capacity, trust and experience of commercial surrogacy in India

PubMed Central

2013-01-01

The socio-ethical concerns regarding exploitation in commercial surrogacy are premised on asymmetric vulnerability and the commercialization of women’s reproductive capacity to suit individualistic motives. In examining the exploitation argument, this article reviews the social contract theory that describes an individual as an ‘economic man’ with moral and/or political motivations to satisfy individual desires. This study considers the critique by feminists, who argue that patriarchal and medical control prevails in the surrogacy contracts. It also explores the exploitative dynamics amongst actors in the light of Baier’s conceptualization of trust and human relationship, within which both justice and exploitation thrive, and Foucault’s concept of bio-power. Drawing on these concepts, this paper aims to investigate the manifestations of exploitation in commercial surrogacy in the context of trust, power and experiences of actors, using a case study of one clinic in India. The actors’ experiences are evaluated at different stages of the surrogacy process: recruitment, medical procedures, living in the surrogate home, bonding with the child and amongst actors, financial dealings, relinquishment and post-relinquishment. This study applies ethnomethodology to identify phenomena as perceived by the actors in a situation, giving importance to their interpretations of the rules that make collective activity possible. The methods include semi-structured interviews, discussions, participant observation and explanation of the phenomena from the actors’ perspectives. Between August 2009 and April 2010, 13 surrogate mothers (SMs), 4 intended parents (IPs) and 2 medical practitioners (MPs) from one clinic in Western India were interviewed. This study reveals that asymmetries of capacity amongst the MPs, SMs, IPs and surrogate agents (SAs) lead to a network of trust and designation of powers through rules, bringing out the relevance of Baier’s conceptualization of asymmetric vulnerability, trust and potential exploitation in human relationships. The IPs are exploited, especially in monetary terms. The SMs are relatively the most exploited, given their vulnerability. Their remuneration through surrogacy is significant for them, and their acquired knowledge as ex-surrogates is used for their own benefit and for exploiting others. Foucault’s conceptualization of power is hence relevant, since the ex-SMs re-invest the power of their exploitative experience in exploiting others. PMID:23962325

QCSEE UTW engine powered-lift acoustic performance

NASA Technical Reports Server (NTRS)

Loeffler, I. J.; Samanich, N. E.; Bloomer, H. E.

1980-01-01

Powered-lift acoustic test of the Quiet Clean Short Haul Experimental Engine (QCSEE) under the wing (UTW) engine are reported. Propulsion systems for two powered-lift concepts were designed, fabricated, and tested. In addition to low noise features, the designs included composite structures, gear-driven fans, digital control, and a variable pitch fan (UTW). The UTW engine was tested in a static ground test facility with wing and flap segments to simulate installation on a short haul transport aircraft of the future. Powered-lift acoustic performance of the UTW engine is compared with that of the previously tested and reported QCSEE over-the-wing (OTW) engine. Both engines were slightly above the noise goal but were significantly below current FAA and modern wide-body jet transport levels. The UTW system in the powered-lift mode was penalized by reflected engine noise from the wing and flap system, while the OTW system was benefitted by a wing noise shielding effect.

14 CFR 33.8 - Selection of engine power and thrust ratings.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Selection of engine power and thrust ratings. 33.8 Section 33.8 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES General § 33.8 Selection of engine power and...

14 CFR 33.8 - Selection of engine power and thrust ratings.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Selection of engine power and thrust ratings. 33.8 Section 33.8 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES General § 33.8 Selection of engine power and...

14 CFR 121.191 - Airplanes: Turbine engine powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Turbine engine powered: En route...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.191 Airplanes: Turbine engine powered: En route limitations: One...

14 CFR 121.193 - Airplanes: Turbine engine powered: En route limitations: Two engines inoperative.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Turbine engine powered: En route...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.193 Airplanes: Turbine engine powered: En route limitations: Two...

14 CFR 121.193 - Airplanes: Turbine engine powered: En route limitations: Two engines inoperative.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Turbine engine powered: En route...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.193 Airplanes: Turbine engine powered: En route limitations: Two...

14 CFR 121.179 - Airplanes: Reciprocating engine-powered: En route limitations: All engines operating.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Reciprocating engine-powered: En...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.179 Airplanes: Reciprocating engine-powered: En route limitations: All...

14 CFR 121.191 - Airplanes: Turbine engine powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Turbine engine powered: En route...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.191 Airplanes: Turbine engine powered: En route limitations: One...

14 CFR 121.193 - Airplanes: Turbine engine powered: En route limitations: Two engines inoperative.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Turbine engine powered: En route...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.193 Airplanes: Turbine engine powered: En route limitations: Two...

14 CFR 121.179 - Airplanes: Reciprocating engine-powered: En route limitations: All engines operating.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Reciprocating engine-powered: En...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.179 Airplanes: Reciprocating engine-powered: En route limitations: All...

14 CFR 121.179 - Airplanes: Reciprocating engine-powered: En route limitations: All engines operating.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Reciprocating engine-powered: En...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.179 Airplanes: Reciprocating engine-powered: En route limitations: All...

14 CFR 121.191 - Airplanes: Turbine engine powered: En route limitations: One engine inoperative.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Turbine engine powered: En route...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.191 Airplanes: Turbine engine powered: En route limitations: One...

14 CFR 121.179 - Airplanes: Reciprocating engine-powered: En route limitations: All engines operating.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Reciprocating engine-powered: En...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.179 Airplanes: Reciprocating engine-powered: En route limitations: All...

14 CFR 121.179 - Airplanes: Reciprocating engine-powered: En route limitations: All engines operating.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Reciprocating engine-powered: En...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.179 Airplanes: Reciprocating engine-powered: En route limitations: All...

A Project-Based Cooperative Approach to Teaching Sustainable Energy Systems

ERIC Educational Resources Information Center

Verbic, Gregor; Keerthisinghe, Chanaka; Chapman, Archie C.

2017-01-01

Engineering education is undergoing a restructuring driven by the needs of an increasingly multidisciplinary engineering profession. At the same time, power systems are transitioning toward future smart grids that will require power engineers with skills outside of the core power engineering domain. Since including new topics in the existing…

Spatiotemporal Patterns and Predictability of Cyberattacks

PubMed Central

Chen, Yu-Zhong; Huang, Zi-Gang; Xu, Shouhuai; Lai, Ying-Cheng

2015-01-01

A relatively unexplored issue in cybersecurity science and engineering is whether there exist intrinsic patterns of cyberattacks. Conventional wisdom favors absence of such patterns due to the overwhelming complexity of the modern cyberspace. Surprisingly, through a detailed analysis of an extensive data set that records the time-dependent frequencies of attacks over a relatively wide range of consecutive IP addresses, we successfully uncover intrinsic spatiotemporal patterns underlying cyberattacks, where the term “spatio” refers to the IP address space. In particular, we focus on analyzing macroscopic properties of the attack traffic flows and identify two main patterns with distinct spatiotemporal characteristics: deterministic and stochastic. Strikingly, there are very few sets of major attackers committing almost all the attacks, since their attack “fingerprints” and target selection scheme can be unequivocally identified according to the very limited number of unique spatiotemporal characteristics, each of which only exists on a consecutive IP region and differs significantly from the others. We utilize a number of quantitative measures, including the flux-fluctuation law, the Markov state transition probability matrix, and predictability measures, to characterize the attack patterns in a comprehensive manner. A general finding is that the attack patterns possess high degrees of predictability, potentially paving the way to anticipating and, consequently, mitigating or even preventing large-scale cyberattacks using macroscopic approaches. PMID:25992837

Management of ATM-based networks supporting multimedia medical information systems

NASA Astrophysics Data System (ADS)

Whitman, Robert A.; Blaine, G. James; Fritz, Kevin; Goodgold, Ken; Heisinger, Patrick

1997-05-01

Medical information systems are acquiring the ability to collect and deliver many different types of medical information. In support of the increased network demands necessitated by these expanded capabilities, asynchronous transfer mode (ATM) based networks are being deployed in medical care systems. While ATM supplies a much greater line rate than currently deployed networks, the management and standards surrounding ATM are yet to mature. This paper explores the management and control issues surrounding an ATM network supporting medical information systems, and examines how management impacts network performance and robustness. A multivendor ATM network at the BJC Health System/Washington University and the applications using the network are discussed. Performance information for specific applications is presented and analyzed. Network management's influence on application reliability is outlined. The information collected is used to show how ATM network standards and management tools influence network reliability and performance. Performance of current applications using the ATM network is discussed. Special attention is given to issues encountered in implementation of hypertext transfer protocol over ATM internet protocol (IP) communications. A classical IP ATM implementation yields greater than twenty percent higher network performance over LANE. Maximum performance for a host's suite of applications can be obtained by establishing multiple individually engineered IP links through its ATM network connection.

Multidisciplinary design optimization of vehicle instrument panel based on multi-objective genetic algorithm

NASA Astrophysics Data System (ADS)

Wang, Ping; Wu, Guangqiang

2013-03-01

Typical multidisciplinary design optimization(MDO) has gradually been proposed to balance performances of lightweight, noise, vibration and harshness(NVH) and safety for instrument panel(IP) structure in the automotive development. Nevertheless, plastic constitutive relation of Polypropylene(PP) under different strain rates, has not been taken into consideration in current reliability-based and collaborative IP MDO design. In this paper, based on tensile test under different strain rates, the constitutive relation of Polypropylene material is studied. Impact simulation tests for head and knee bolster are carried out to meet the regulation of FMVSS 201 and FMVSS 208, respectively. NVH analysis is performed to obtain mainly the natural frequencies and corresponding mode shapes, while the crashworthiness analysis is employed to examine the crash behavior of IP structure. With the consideration of lightweight, NVH, head and knee bolster impact performance, design of experiment(DOE), response surface model(RSM), and collaborative optimization(CO) are applied to realize the determined and reliability-based optimizations, respectively. Furthermore, based on multi-objective genetic algorithm(MOGA), the optimal Pareto sets are completed to solve the multi-objective optimization(MOO) problem. The proposed research ensures the smoothness of Pareto set, enhances the ability of engineers to make a comprehensive decision about multi-objectives and choose the optimal design, and improves the quality and efficiency of MDO.

Spatiotemporal patterns and predictability of cyberattacks.

PubMed

Chen, Yu-Zhong; Huang, Zi-Gang; Xu, Shouhuai; Lai, Ying-Cheng

2015-01-01

A relatively unexplored issue in cybersecurity science and engineering is whether there exist intrinsic patterns of cyberattacks. Conventional wisdom favors absence of such patterns due to the overwhelming complexity of the modern cyberspace. Surprisingly, through a detailed analysis of an extensive data set that records the time-dependent frequencies of attacks over a relatively wide range of consecutive IP addresses, we successfully uncover intrinsic spatiotemporal patterns underlying cyberattacks, where the term "spatio" refers to the IP address space. In particular, we focus on analyzing macroscopic properties of the attack traffic flows and identify two main patterns with distinct spatiotemporal characteristics: deterministic and stochastic. Strikingly, there are very few sets of major attackers committing almost all the attacks, since their attack "fingerprints" and target selection scheme can be unequivocally identified according to the very limited number of unique spatiotemporal characteristics, each of which only exists on a consecutive IP region and differs significantly from the others. We utilize a number of quantitative measures, including the flux-fluctuation law, the Markov state transition probability matrix, and predictability measures, to characterize the attack patterns in a comprehensive manner. A general finding is that the attack patterns possess high degrees of predictability, potentially paving the way to anticipating and, consequently, mitigating or even preventing large-scale cyberattacks using macroscopic approaches.

Electromagnetic compatibility of PLC adapters for in-home/domestic networks

NASA Astrophysics Data System (ADS)

Potisk, Lukas; Hallon, Jozef; Orgon, Milos; Fujdiak, Radek

2018-01-01

The use of programable logic controllers (PLC) technology in electrical networks 230 V causes electromagnetic radiation that interferes with other electrical equipment connected to the network [1-4]. Therefore, this article describes the issues of electromagnetic compatibility (EMC) of new PLC adapters used in IP broadband services in a multi-user environment. The measurements of disturbing electromagnetic field originated in PLC adapters were made in a certified laboratory EMC (laboratory of electromagnetic compatibility) in the Institute of Electrical Engineering at Faculty of Electrical Engineering and Information Technology of the Slovak University of Technology in Bratislava. The measured spectra of the radiated electromagnetic field will be compared with the results obtained when testing older PLC modems [5].

Possible ways of reducing the effect of thermal power facilities on the environment

NASA Astrophysics Data System (ADS)

Zroichikov, N. A.; Prokhorov, V. B.; Tupov, V. B.; Arkhipov, A. M.; Fomenko, M. V.

2015-02-01

The main trends in the integrated solution of thermal power engineering environmental problems are pointed out taking the Mosenergo power company as an example, and the data are given with respect to the structure of the power engineering equipment of the city of Moscow and its change, energy consumption, and generation of heat and electric energy. The dynamics of atmospheric air pollution of Moscow from 1990 to 2010, as well as the main measures on reducing the adverse effect of the power engineering equipment operation, is given. The results of original designs by the Department of Boiler Installations and Power Engineering Ecology (KU&EE) are given concerning the reduction of nitrogen oxides emissions and the decrease of the noise impact produced by the power engineering equipment.

Integrated control system and method

DOEpatents

Wang, Paul Sai Keat; Baldwin, Darryl; Kim, Myoungjin

2013-10-29

An integrated control system for use with an engine connected to a generator providing electrical power to a switchgear is disclosed. The engine receives gas produced by a gasifier. The control system includes an electronic controller associated with the gasifier, engine, generator, and switchgear. A gas flow sensor monitors a gas flow from the gasifier to the engine through an engine gas control valve and provides a gas flow signal to the electronic controller. A gas oversupply sensor monitors a gas oversupply from the gasifier and provides an oversupply signal indicative of gas not provided to the engine. A power output sensor monitors a power output of the switchgear and provide a power output signal. The electronic controller changes gas production of the gasifier and the power output rating of the switchgear based on the gas flow signal, the oversupply signal, and the power output signal.

Effect of Electromagnetic Stirring on Weld Pools.

DTIC Science & Technology

1983-10-01

R136 71S EFFECT OF ELECTROMAGNET1C STIRRING ON WELD POOL5(U) i/lD DAVID W TAYLOR NAVAL SH-IP RE5ERRCH AND DEVELOPMENT CENTER ANN. R DENRLE ET RL...COMMANDER TECHNICAL DIRECTOR 01 OFFICER-IN-CHARGE OFFICER-IN-CHARGE CARDEROCK ANNAPOLIS 06 04 SYSTEMS DEVELOPMENT DEPARTMENT 11 SHIP PERFORMANCE AVIATION AND...SHIP ACOUSTICS PROPULSION AND DEPARTMENT AUXILIARY SYSTEMS DEPARTMENT 19 27 SHIP MATERIALS CENTRAL ENGINEERING INSTRUMENTATION DEPARTMENT DEPARTMENT28

A Cluster Analytic Approach to Identifying Predictors and Moderators of Psychosocial Treatment for Bipolar Depression: Results from STEP-BD

PubMed Central

Deckersbach, Thilo; Peters, Amy T.; Sylvia, Louisa G.; Gold, Alexandra K.; da Silva Magalhaes, Pedro Vieira; Henry, David B.; Frank, Ellen; Otto, Michael W.; Berk, Michael; Dougherty, Darin D.; Nierenberg, Andrew A.; Miklowitz, David J.

2016-01-01

Background We sought to address how predictors and moderators of psychotherapy for bipolar depression – identified individually in prior analyses – can inform the development of a metric for prospectively classifying treatment outcome in intensive psychotherapy (IP) versus collaborative care (CC) adjunctive to pharmacotherapy in the Systematic Treatment Enhancement Program (STEP-BD) study. Methods We conducted post-hoc analyses on 135 STEP-BD participants using cluster analysis to identify subsets of participants with similar clinical profiles and investigated this combined metric as a moderator and predictor of response to IP. We used agglomerative hierarchical cluster analyses and k-means clustering to determine the content of the clinical profiles. Logistic regression and Cox proportional hazard models were used to evaluate whether the resulting clusters predicted or moderated likelihood of recovery or time until recovery. Results The cluster analysis yielded a two-cluster solution: 1) “less-recurrent/severe” and 2) “chronic/recurrent.” Rates of recovery in IP were similar for less-recurrent/severe and chronic/recurrent participants. Less-recurrent/severe patients were more likely than chronic/recurrent patients to achieve recovery in CC (p = .040, OR = 4.56). IP yielded a faster recovery for chronic/recurrent participants, whereas CC led to recovery sooner in the less-recurrent/severe cluster (p = .034, OR = 2.62). Limitations Cluster analyses require list-wise deletion of cases with missing data so we were unable to conduct analyses on all STEP-BD participants. Conclusions A well-powered, parametric approach can distinguish patients based on illness history and provide clinicians with symptom profiles of patients that confer differential prognosis in CC vs. IP. PMID:27289316

40 CFR 1045.5 - Which engines are excluded from this part's requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND... natural gas engines. Propulsion marine engines powered by natural gas with maximum engine power at or...

40 CFR 1045.5 - Which engines are excluded from this part's requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND... natural gas engines. Propulsion marine engines powered by natural gas with maximum engine power at or...

40 CFR 1045.5 - Which engines are excluded from this part's requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND... natural gas engines. Propulsion marine engines powered by natural gas with maximum engine power at or...

40 CFR 1045.5 - Which engines are excluded from this part's requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND... natural gas engines. Propulsion marine engines powered by natural gas with maximum engine power at or...

40 CFR 1045.5 - Which engines are excluded from this part's requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND... natural gas engines. Propulsion marine engines powered by natural gas with maximum engine power at or...

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The New York Power Authority (NYPA) and Entergy Corp. of New Orleans, La., announced recently the signing of a memorandum of understanding as a step toward a contract for Entergy to provide management services to NYPA`s two nuclear power plants. The agreement is the first of its kind. NYPA is the nation`s largest state-owned electric utility and supplier of one-quarter of New York`s electricity. Its nuclear plants are Indian Point 3 (IP3) in Buchanan, Westchester County, and James A. FitzPatrick in Scriba, Oswego County. Entergy is a utility holding company and its subsidiary, Entergy Operations Inc., is widely recognized asmore » one of the leading nuclear operators in the United States. {open_quotes}NYPA`s nuclear plants are assets that belong to the people of New York,{close_quotes} said C.D. {open_quotes}Rapp{close_quotes} Rappleyea, NYPA`s chairman and CEO. {open_quotes}Our alliance with Entergy can provide the people of this state with added assurance that these plants will operate with the highest level of safety and efficiency.{close_quotes} FitzPatrick, an 800 MW boiling water reactor, has operated since 1975 and IP3, a 980 MW pressurized water reactor, since 1976. Although both are currently running well, they have had problems in recent years, and IP3 is on the US Nuclear Regulatory Commission`s (NRC) list of plants requiring increased regulatory attention. Entergy operated both types of reactors, has three single-unit sites like NYPA`s and is experienced in operating plants for different utility owners.« less

40 CFR 1042.135 - Labeling.

Code of Federal Regulations, 2011 CFR

2011-07-01

... label. (e) For engines requiring ULSD, create a separate label with the statement: “ULTRA LOW SULFUR... power (in kW), and power density (in kW/L) as needed to determine the emission standards for the engine family. You may specify displacement, maximum engine power, or power density as a range consistent with...

14 CFR 23.77 - Balked landing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... reciprocating engine-powered and single engine turbine powered airplane of more than 6,000 pounds maximum weight, and multiengine turbine engine-powered airplane of 6,000 pounds or less maximum weight in the normal... of movement of the power controls from minimum flight-idle position; (2) The landing gear extended...

14 CFR 23.77 - Balked landing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... reciprocating engine-powered and single engine turbine powered airplane of more than 6,000 pounds maximum weight, and multiengine turbine engine-powered airplane of 6,000 pounds or less maximum weight in the normal... of movement of the power controls from minimum flight-idle position; (2) The landing gear extended...

An advanced concept secondary power systems study for an advanced transport technology aircraft

NASA Technical Reports Server (NTRS)

1972-01-01

The application of advanced technology to the design of an integrated secondary power system for future near-sonic long-range transports was investigated. The study showed that the highest payoff is achieved by utilizing secondary power equipment that contributes to minimum cruise drag. This is best accomplished by the use of the dedicated auxiliary power unit concept (inflight APU) as the prime power source for an airplane with a body-mounted engine or by the use of the internal engine generator concept (electrical power extraction from the propulsion engine) for an airplane with a wing-pod-mounted engine.

Contingency power concepts for helicopter turboshaft engine

NASA Technical Reports Server (NTRS)

Hirschkron, R.; Davis, R. H.; Goldstein, D. N.; Haynes, J. F.; Gauntner, J. W.

1984-01-01

Twin helicopter engines are often sized by power requirement of safe mission completion after the failure of one of the two engines. This study was undertaken for NASA Lewis by General Electric Co. to evaluate the merits of special design features to provide a 2-1/2 minute Contingency Power rating, permitting an engine size reduction. The merits of water injection, cooling flow modulation, throttle push and an auxiliary power plant were evaluated using military life cycle cost (LCC) and commercial helicopter direct operating cost (DOC) merit factors in a rubber engine/rubber aircraft scenario.

14 CFR 135.383 - Large transport category airplanes: Turbine engine powered: En route limitations: Two engines...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Large transport category airplanes: Turbine... Limitations § 135.383 Large transport category airplanes: Turbine engine powered: En route limitations: Two...). No person may operate a turbine engine powered large transport category airplane along an intended...

14 CFR 135.383 - Large transport category airplanes: Turbine engine powered: En route limitations: Two engines...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Large transport category airplanes: Turbine... Limitations § 135.383 Large transport category airplanes: Turbine engine powered: En route limitations: Two...). No person may operate a turbine engine powered large transport category airplane along an intended...

14 CFR 135.383 - Large transport category airplanes: Turbine engine powered: En route limitations: Two engines...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Large transport category airplanes: Turbine... Limitations § 135.383 Large transport category airplanes: Turbine engine powered: En route limitations: Two...). No person may operate a turbine engine powered large transport category airplane along an intended...

Heat engine development for solar thermal power systems

NASA Technical Reports Server (NTRS)

Pham, H. Q.; Jaffe, L. D.

1981-01-01

The technical status of three heat engines (Stirling, high-temperature Brayton, and Combined cycle) for use in solar thermal power systems is presented. Performance goals necessary to develop a system competitive with conventional power requirements include an external heated engine output less than 40 kW, and efficiency power conversion subsystem at least 40% at rated output, and a half-power efficiency of at least 37%. Results show that the Stirling engine can offer a 39% efficiency with 100 hours of life, and a 20% efficiency with 10,000 hours of life, but problems with seals and heater heads exist. With a demonstrated efficiency near 31% at 1500 F and a minimum lifetime of 100,000 hours, the Brayton engine does not offer sufficient engine lifetime, efficiency, and maintenance for solar thermal power systems. Examination of the Rankine bottoming cycle of the Combined cycle engine reveals a 30 year lifetime, but a low efficiency. Additional development of engines for solar use is primarily in the areas of components to provide a long lifetime, high reliability, and low maintenance (no more than $0.001/kW-hr).

Grid Integration Science, NREL Power Systems Engineering Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kroposki, Benjamin

This report highlights journal articles published in 2016 by researchers in the Power Systems Engineering Center. NREL's Power Systems Engineering Center published 47 journal and magazine articles in the past year, highlighting recent research in grid modernization.

14 CFR 29.1305 - Powerplant instruments.

Code of Federal Regulations, 2013 CFR

2013-01-01

... temperature indicator for each turbine engine; (12) A gas producer rotor tachometer for each turbine engine... free power turbine tachometer for each turbine engine; (16) A means, for each turbine engine, to indicate power for that engine; (17) For each turbine engine, an indicator to indicate the functioning of...

14 CFR 29.1305 - Powerplant instruments.

Code of Federal Regulations, 2010 CFR

2010-01-01

... temperature indicator for each turbine engine; (12) A gas producer rotor tachometer for each turbine engine... free power turbine tachometer for each turbine engine; (16) A means, for each turbine engine, to indicate power for that engine; (17) For each turbine engine, an indicator to indicate the functioning of...

14 CFR 29.1305 - Powerplant instruments.

Code of Federal Regulations, 2012 CFR

2012-01-01

... temperature indicator for each turbine engine; (12) A gas producer rotor tachometer for each turbine engine... free power turbine tachometer for each turbine engine; (16) A means, for each turbine engine, to indicate power for that engine; (17) For each turbine engine, an indicator to indicate the functioning of...

14 CFR 29.1305 - Powerplant instruments.

Code of Federal Regulations, 2014 CFR

2014-01-01

... temperature indicator for each turbine engine; (12) A gas producer rotor tachometer for each turbine engine... free power turbine tachometer for each turbine engine; (16) A means, for each turbine engine, to indicate power for that engine; (17) For each turbine engine, an indicator to indicate the functioning of...

14 CFR 29.1305 - Powerplant instruments.

Code of Federal Regulations, 2011 CFR

2011-01-01

... temperature indicator for each turbine engine; (12) A gas producer rotor tachometer for each turbine engine... free power turbine tachometer for each turbine engine; (16) A means, for each turbine engine, to indicate power for that engine; (17) For each turbine engine, an indicator to indicate the functioning of...

14 CFR 23.49 - Stalling period.

Code of Federal Regulations, 2011 CFR

2011-01-01

... on the stalling speed, with engine(s) idling and throttle(s) closed; (3) The propeller(s) in the... which the airplane is controllable with— (1) For reciprocating engine-powered airplanes, the engine(s... more than 110 percent of the stalling speed; (2) For turbine engine-powered airplanes, the propulsive...

Learning Platform for Study of Power Electronic Application in Power Systems

ERIC Educational Resources Information Center

Bauer, P.; Rompelman, O.

2005-01-01

Present engineering has to deal with increasingly complex systems. In particular, this is the case in electrical engineering. Though this is obvious in microelectronics, also in the field of power systems engineers have to design, operate and maintain highly complex systems such as power grids, energy converters and electrical drives. This is…

33 CFR 209.140 - Operations of the Corps of Engineers under the Federal Power Act.

Code of Federal Regulations, 2012 CFR

2012-07-01

... structures filed with the Federal Power Commission in connection with licensing of non-Federal hydroelectric... Engineers under the Federal Power Act. 209.140 Section 209.140 Navigation and Navigable Waters CORPS OF... the Corps of Engineers under the Federal Power Act. (a) General. This section outlines policies and...

33 CFR 209.140 - Operations of the Corps of Engineers under the Federal Power Act.

Code of Federal Regulations, 2014 CFR

2014-07-01

... structures filed with the Federal Power Commission in connection with licensing of non-Federal hydroelectric... Engineers under the Federal Power Act. 209.140 Section 209.140 Navigation and Navigable Waters CORPS OF... the Corps of Engineers under the Federal Power Act. (a) General. This section outlines policies and...

33 CFR 209.140 - Operations of the Corps of Engineers under the Federal Power Act.

Code of Federal Regulations, 2013 CFR

2013-07-01

... structures filed with the Federal Power Commission in connection with licensing of non-Federal hydroelectric... Engineers under the Federal Power Act. 209.140 Section 209.140 Navigation and Navigable Waters CORPS OF... the Corps of Engineers under the Federal Power Act. (a) General. This section outlines policies and...

Comparative toxicity and efficacy of engineered anthrax lethal toxin variants with broad anti-tumor activities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, Diane E.; Program of Pharmacology and Experimental Therapeutics, Tufts University School of Medicine, Boston, MA; Hoover, Benjamin

2014-09-01

We have previously designed and characterized versions of anthrax lethal toxin that are selectively cytotoxic in the tumor microenvironment and which display broad and potent anti-tumor activities in vivo. Here, we have performed the first direct comparison of the safety and efficacy of three engineered anthrax lethal toxin variants requiring activation by either matrix-metalloproteinases (MMPs), urokinase plasminogen activator (uPA) or co-localized MMP/uPA activities. C57BL/6J mice were challenged with six doses of engineered toxins via intraperitoneal (I.P.) or intravenous (I.V.) dose routes to determine the maximum tolerated dose for six administrations (MTD6) and dose-limiting toxicities. Efficacy was evaluated using the B16-BL6more » syngraft model of melanoma; mice bearing established tumors were treated with six I.P. doses of toxin and tumor measurements and immunohistochemistry, paired with terminal blood work, were used to elaborate upon the anti-tumor mechanism and relative efficacy of each variant. We found that MMP-, uPA- and dual MMP/uPA-activated anthrax lethal toxins exhibited the same dose-limiting toxicity; dose-dependent GI toxicity. In terms of efficacy, all three toxins significantly reduced primary B16-BL6 tumor burden, ranging from 32% to 87% reduction, and they also delayed disease progression as evidenced by dose-dependent normalization of blood work values. While target organ toxicity and effective doses were similar amongst the variants, the dual MMP/uPA-activated anthrax lethal toxin exhibited the highest I.P. MTD6 and was 1.5–3-fold better tolerated than the single MMP- and uPA-activated toxins. Overall, we demonstrate that this dual MMP/uPA-activated anthrax lethal toxin can be administered safely and is highly effective in a preclinical model of melanoma. This modified bacterial cytotoxin is thus a promising candidate for further clinical development and evaluation for use in treating human cancers. - Highlights: • Toxicity and anti-tumor activity of protease-activated anthrax toxins were evaluated. • All anthrax toxin variants exhibited potent systemic anti-tumor activity in mice. • A dual MMP/uPA-activated anthrax toxin displayed a superior safety profile. • Clinical development of a dual MMP/uPA-activated anthrax toxin is feasible.« less

Theoretical Studies of High-Power Ultraviolet and Infrared Materials

DTIC Science & Technology

1975-06-30

pgpj|WmHm.. HH nyn^imwii,. ■ HW-HM»’ BUsmn.u’iiw: Sec. B III. IONIZATION FREQUENCY Current theories do not explain the experimentally determined...PWW.WlJJJlVl BW«»?»«.! • ~™K?T"^ ,!J!.MllkW,,»JW",i...li.U’iP’"l’’.l •I.IIUJ.PW»«»*! iJl.IIMlJHIi.il I» ™"T5f-5- ill.NH»llii.iJJn*ll, JB ...34 ’’ "^»WIW*»**1!"*™*"?1 -;T’wiBwmmuij»w»w«i " v«i «««..win | ip^pi«»m>!PWH« HH ^pr« Sec. E The frequency dependence of the

75 FR 21653 - Commercial Leasing for Wind Power on the Outer Continental Shelf (OCS) Offshore Delaware-Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-26

... to enable MMS to gauge specific interest in commercial development of OCS wind resources in the area... (IP) to allow the issuance of leases to assess the renewable energy resource potential on the OCS and... resources that will guarantee stable prices for electricity. The Delaware legislature also passed a...

10 CFR Appendix S to Part 50 - Earthquake Engineering Criteria for Nuclear Power Plants

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Earthquake Engineering Criteria for Nuclear Power Plants S... FACILITIES Pt. 50, App. S Appendix S to Part 50—Earthquake Engineering Criteria for Nuclear Power Plants... applicant or holder whose construction permit was issued before January 10, 1997, the earthquake engineering...

10 CFR Appendix S to Part 50 - Earthquake Engineering Criteria for Nuclear Power Plants

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Earthquake Engineering Criteria for Nuclear Power Plants S... FACILITIES Pt. 50, App. S Appendix S to Part 50—Earthquake Engineering Criteria for Nuclear Power Plants... applicant or holder whose construction permit was issued before January 10, 1997, the earthquake engineering...

10 CFR Appendix S to Part 50 - Earthquake Engineering Criteria for Nuclear Power Plants

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Earthquake Engineering Criteria for Nuclear Power Plants S... FACILITIES Pt. 50, App. S Appendix S to Part 50—Earthquake Engineering Criteria for Nuclear Power Plants... applicant or holder whose construction permit was issued before January 10, 1997, the earthquake engineering...

10 CFR Appendix S to Part 50 - Earthquake Engineering Criteria for Nuclear Power Plants

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Earthquake Engineering Criteria for Nuclear Power Plants S... FACILITIES Pt. 50, App. S Appendix S to Part 50—Earthquake Engineering Criteria for Nuclear Power Plants... applicant or holder whose construction permit was issued before January 10, 1997, the earthquake engineering...

14 CFR 33.84 - Engine overtorque test.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.84 Engine overtorque test. (a) If approval of a maximum engine overtorque is sought for an engine incorporating a free power turbine... at least 21/2 minutes duration. (2) A power turbine rotational speed equal to the highest speed at...

14 CFR 33.84 - Engine overtorque test.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.84 Engine overtorque test. (a) If approval of a maximum engine overtorque is sought for an engine incorporating a free power turbine... at least 21/2 minutes duration. (2) A power turbine rotational speed equal to the highest speed at...

14 CFR 33.84 - Engine overtorque test.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.84 Engine overtorque test. (a) If approval of a maximum engine overtorque is sought for an engine incorporating a free power turbine... at least 21/2 minutes duration. (2) A power turbine rotational speed equal to the highest speed at...

TOPSIS-based parametric optimization of compression ignition engine performance and emission behavior with bael oil blends for different EGR and charge inlet temperature.

PubMed

Muniappan, Krishnamoorthi; Rajalingam, Malayalamurthi

2018-05-02

The demand for higher fuel energy and lesser exhaust emissions of diesel engines can be achieved by fuel being used and engine operating parameters. In the present work, effects of engine speed (RPM), injection timing (IT), injection pressure (IP), and compression ratio (CR) on performance and emission characteristics of a compression ignition (CI) engine were investigated. The ternary test fuel of 65% diesel + 25% bael oil + 10% diethyl ether (DEE) was used in this work and test was conducted at different charge inlet temperature (CIT) and exhaust gas recirculation (EGR). All the experiments are conducted at the tradeoff engine load that is 75% engine load. When operating the diesel engine with 320 K CIT, brake thermal efficiency (BTE) is improved to 28.6%, and carbon monoxide (CO) and hydrocarbon (HC) emissions have been reduced to 0.025% and 12.5 ppm at 18 CR. The oxide of nitrogen (NOx) has been reduced to 240 ppm at 1500 rpm for 30% EGR mode. Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) method is frequently used in multi-factor selection and gray correlation analysis method is used to study uncertain of the systems.

Study, optimization, and design of a laser heat engine. [for satellite applications

NASA Technical Reports Server (NTRS)

Taussig, R. T.; Cassady, P. E.; Zumdieck, J. F.

1978-01-01

Laser heat engine concepts, proposed for satellite applications, are analyzed to determine which engine concept best meets the requirements of high efficiency (50 percent or better), continuous operation in space using near-term technology. The analysis of laser heat engines includes the thermodynamic cycles, engine design, laser power sources, collector/concentrator optics, receiving windows, absorbers, working fluids, electricity generation, and heat rejection. Specific engine concepts, optimized according to thermal efficiency, are rated by their technological availability and scaling to higher powers. A near-term experimental demonstration of the laser heat engine concept appears feasible utilizing an Otto cycle powered by CO2 laser radiation coupled into the engine through a diamond window. Higher cycle temperatures, higher efficiencies, and scalability to larger sizes appear to be achievable from a laser heat engine design based on the Brayton cycle and powered by a CO laser.

The Dawn of Vesta Science

NASA Technical Reports Server (NTRS)

Garner, Charles E.; Rayman, Marc D.; Brophy, John R.; Mikes, Steven C.

2011-01-01

The Dawn mission is part of NASA's Discovery Program and has as its goal the scientific exploration of the two most massive main-belt asteroids, Vesta and Ceres. The Dawn spacecraft was launched from the Cape Canaveral Air Force Station on September 27, 2007 on a Delta-II 7925H-9.5 (Delta-II Heavy) rocket that placed the 1218-kg spacecraft onto an Earth-escape trajectory. On-board the spacecraft is an ion propulsion system (IPS) developed at the Jet Propulsion Laboratory which will provide a total ?V of 11.3 km/s for the heliocentric transfer to Vesta, orbit capture at Vesta, transfer between Vesta science orbits, departure and escape from Vesta, heliocentric transfer to Ceres, orbit capture at Ceres, and transfer between Ceres science orbits. Fullpower thrusting from December 2007 through October 2008 was used to successfully target a Mars gravity assist flyby in February 2009 that provided an additional ?V of 2.6 km/s. Deterministic thrusting for the heliocentric transfer to Vesta resumed in June 2009 and concluded with orbit capture at Vesta on July 16, 2011. An additional 210 hours of IPS thrusting was used to enter the first Vesta science orbit, called Survey orbit, on August 3, 2011 at an altitude of approximately 2,735 km. To date the IPS has been operated for 23,621 hours, consumed approximately 252 kg of xenon, and provided a delta-V of approximately 6.7 km/s. The IPS performance characteristics are very close to the expected performance based on analysis and testing performed pre-launch. The only significant issue in over the almost four years of IPS operations in flight was the temporary failure of a valve driver board in the Digital Control and Interface Unit-1 (DCIU-1), resulting in a loss of thrust of approximately 29 hours. Thrusting operations resumed after switching to DCIU-2, and power cycling conducted after orbit capture restored DCIU-1 to full functionality. After about three weeks of Survey orbit operations the IPS will be used to transfer the spacecraft to the other planned science orbit altitudes. After approximately one year of science operations the IPS will be used for escape from Vesta and then for thrusting to Ceres with a planned arrival date at Ceres in February 2015. This paper provides an overview of Dawn's mission objectives and the results of Dawn IPS mission operations through the start of science operations at Vesta.

Pushing in labor: performance and not endurance.

PubMed

Buhimschi, Catalin S; Buhimschi, Irina A; Malinow, Andrew M; Kopelman, Jerome N; Weiner, Carl P

2002-06-01

It is believed that delivery is faster if women are instructed to voluntarily bear down in synchrony with their uterine contractions. Confronted by the large variance in the duration of the second stage of labor, many clinicians attribute a "fast" or a "short" expulsion time solely to the patient's willingness to cooperate or to the strength of epidural anesthesia if it is a factor. Yet, knowledge of pushing performance and the factors affecting it remain limited. We investigated the maternal, fetal, and labor characteristics that influence the maternal "pushing performance" and sought to design a predictive index that prospectively identified "high" versus "low" pushing performers. Intrauterine pressure (IP) was prospectively measured during the second stage of labor in 52 women recruited at one North American hospital. Recordings were begun after documentation of full cervical dilatation and descent of the fetal head to +2 station (on a -3/+3 scale). Each woman acted as her own control, received epidural anesthesia, and was alert and responsive throughout the study. Pushing (closed glottis technique) was performed in a standardized fashion. Multivariate analysis with linear regression was applied to identify significant associations between maternal, fetal, or labor characteristics as the independent variables and the percent increase in IP consequent to active pushing as the dependent variable. Women in labor increase their IP 62% by actively pushing with a contraction during the second stage. A scattergram of the individual percent increase above the baseline IP integral revealed that for some women, pushing more readily increased their IP than it did for others (range, 0% to 192%). The percent increase was best calculated by a linear combination of myometrial thickness, estimated fetal weight, the maternal body mass index, and the obstetric need for labor augmentation (P =.007, r = 0.52, power = 0.975). A 66% change in IP provided the best separation between high and low pushing performance. Myometrial thickness provided the single strongest contribution to the regression equation's predictive value (P =.01, r = -0.36). A myometrial thickness of 6 mm had a specificity of 88% (but only 53% sensitivity) for the identification of women able to increase their IP by 66% over baseline. In women in labor who have received epidural anesthesia, the efficiency with which maternal expulsive efforts are converted into increased IP is directly related to the patient's body mass index but inversely related to myometrial thickness, the sonographic estimate of fetal weight, and the need for labor augmentation.

MEMS Rotary Engine Power System

NASA Astrophysics Data System (ADS)

Fernandez-Pello, A. Carlos; Pisano, Albert P.; Fu, Kelvin; Walther, David C.; Knobloch, Aaron; Martinez, Fabian; Senesky, Matt; Stoldt, Conrad; Maboudian, Roya; Sanders, Seth; Liepmann, Dorian

This work presents a project overview and recent research results for the MEMS Rotary Engine Power System project at the Berkeley Sensor & Actuator Center of the University of California at Berkeley. The research motivation for the project is the high specific energy density of hydrocarbon fuels. When compared with the energy density of batteries, hydrocarbon fuels may have as much as 20x more energy. However, the technical challenge is the conversion of hydrocarbon fuel to electricity in an efficient and clean micro engine. A 12.9 mm diameter Wankel engine will be shown that has already generated 4 Watts of power at 9300rpm. In addition, the 1mm and 2.4 mm Wankel engines that BSAC is developing for power generation at the microscale will be discussed. The project goal is to develop electrical power output of 90milliwatts from the 2.4 mm engine. Prototype engine components have already been fabricated and these will be described. The integrated generator design concept utilizes a nickel-iron alloy electroplated in the engine rotor poles, so that the engine rotor also serves as the generator rotor.

14 CFR 121.175 - Airplanes: Reciprocating engine-powered: Weight limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.175 Airplanes: Reciprocating engine-powered: Weight limitations. (a...

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

14 CFR 121.175 - Airplanes: Reciprocating engine-powered: Weight limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.175 Airplanes: Reciprocating engine-powered: Weight limitations. (a...

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

14 CFR 121.175 - Airplanes: Reciprocating engine-powered: Weight limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.175 Airplanes: Reciprocating engine-powered: Weight limitations. (a...

14 CFR 121.175 - Airplanes: Reciprocating engine-powered: Weight limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.175 Airplanes: Reciprocating engine-powered: Weight limitations. (a...

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

14 CFR 121.175 - Airplanes: Reciprocating engine-powered: Weight limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.175 Airplanes: Reciprocating engine-powered: Weight limitations. (a...

Strategic patent analysis in plant biotechnology: terpenoid indole alkaloid metabolic engineering as a case study.

PubMed

Miralpeix, Bruna; Sabalza, Maite; Twyman, Richard M; Capell, Teresa; Christou, Paul

2014-02-01

The do-it-yourself patent search is a useful alternative to professional patent analysis particularly in the context of publicly funded projects where funds for IP activities may be limited. As a case study, we analysed patents related to the engineering of terpenoid indole alkaloid (TIA) metabolism in plants. We developed a focused search strategy to remove redundancy and reduce the workload without missing important and relevant patents. This resulted in the identification of approximately 50 key patents associated with TIA metabolic engineering in plants, which could form the basis of a more detailed freedom-to-operate analysis. The structural elements of this search strategy could easily be transferred to other contexts, making it a useful generic model for publicly funded research projects. © 2014 Society for Experimental Biology, Association of Applied Biologists and John Wiley & Sons Ltd.

Generation of Custom DSP Transform IP Cores: Case Study Walsh-Hadamard Transform

DTIC Science & Technology

2002-09-01

mathematics and hardware design What I know: Finite state machine Pipelining Systolic array … What I know: Linear algebra Digital signal processing...state machine Pipelining Systolic array … What I know: Linear algebra Digital signal processing Adaptive filter theory … A math guy A hardware engineer...Synthesis Technology Libary Bit-width (8) HF factor (1,2,3,6) VF factor (1,2,4, ... 32) Xilinx FPGA Place&Route Xilinx FPGA Place&Route Performance

Empirical development of ground acceleration, velocity, and displacement for accidental explosions at J5 or the proposed large altitude rocket cell at Arnold Engineering Development Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, B.C.

This study is an assessment of the ground shock which may be generated in the event of an accidental explosion at J5 or the Proposed Large Altitude Rocket Cell (LARC) at the Arnold Engineering Development Center (AEDC). The assessment is accomplished by reviewing existing empirical relationships for predicting ground motion from ground shock. These relationships are compared with data for surface explosions at sites with similar geology and with yields similar to expected conditions at AEDC. Empirical relationships are developed from these data and a judgment made whether to use existing empirical relationships or the relationships developed in this study.more » An existing relationship (Lipner et al.) is used to predict velocity; the empirical relationships developed in the course of this study are used to predict acceleration and displacement. The ground motions are presented in table form and as contour plots. Included also is a discussion of damage criteria from blast and earthquake studies. This report recommends using velocity rather than acceleration as an indicator of structural blast damage. It is recommended that v = 2 ips (v = .167 fps) be used as the damage threshold value (no major damage for v less than or equal to 2 ips). 13 references, 25 figures, 6 tables.« less

Can 100Gb/s wavelengths be deployed using 10Gb/s engineering rules?

NASA Astrophysics Data System (ADS)

Saunders, Ross; Nicholl, Gary; Wollenweber, Kevin; Schmidt, Ted

2007-09-01

A key challenge set by carriers for 40Gb/s deployments was that the 40Gb/s wavelengths should be deployable over existing 10Gb/s DWDM systems, using 10Gb/s link engineering design rules. Typical 10Gb/s link engineering rules are: 1. Polarization Mode Dispersion (PMD) tolerance of 10ps (mean); 2. Chromatic Dispersion (CD) tolerance of +/-700ps/nm 3. Operation at 50GHz channel spacing, including transit through multiple cascaded [R]OADMs; 4. Optical reach up to 2,000km. By using a combination of advanced modulation formats and adaptive dispersion compensation (technologies rarely seen at 10Gb/s outside of the submarine systems space), vendors did respond to the challenge and broadly met this requirement. As we now start to explore feasible technologies for 100Gb/s optical transport, driven by 100GE port availability on core IP routers, the carrier challenge remains the same. 100Gb/s links should be deployable over existing 10Gb/s DWDM systems using 10Gb/s link engineering rules (as listed above). To meet this challenge, optical transport technology must evolve to yet another level of complexity/maturity in both modulation formats and adaptive compensation techniques. Many clues as to how this might be achieved can be gained by first studying sister telecommunications industries, e.g. satellite (QPSK, QAM, LDCP FEC codes), wireless (advanced DSP, MSK), HDTV (TCM), etc. The optical industry is not a pioneer of new ideas in modulation schemes and coding theory, we will always be followers. However, we do have the responsibility of developing the highest capacity "modems" on the planet to carry the core backbone traffic of the Internet. As such, the key to our success will be to analyze the pros and cons of advanced modulation/coding techniques and balance this with the practical limitations of high speed electronics processing speed and the challenges of real world optical layer impairments. This invited paper will present a view on what advanced technologies are likely candidates to support 100GE optical IP transport over existing 10Gb/s DWDM systems, using 10Gb/s link engineering rules.

Prospects of Pluripotent and Adult Stem Cells for Rare Diseases.

PubMed

García-Castro, Javier; Singeç, Ilyas

2017-01-01

Rare diseases are highly diverse and complex regarding molecular underpinning and clinical manifestation and afflict millions of patients worldwide. The lack of appropriate model systems with face and construct validity and the limited availability of live tissues and cells from patients has largely hampered the understanding of underlying disease mechanisms. As a consequence, there are no adequate treatment options available for the vast majority of rare diseases. Over the last decade, remarkable progress in pluripotent and adult stem cell biology and the advent of powerful genomic technologies opened up exciting new avenues for the investigation, diagnosis, and personalized therapy of intractable human diseases. Utilizing the entire range of available stem cell types will continue to cross-fertilize different research areas and leverage the investigation of rare diseases based on evidence-based medicine. Standardized cell engineering and manufacturing from inexhaustible stem cell sources should lay the foundation for next-generation drug discovery and cell therapies that are broadly applicable in regenerative medicine. In this chapter we discuss how patient- and disease-specific iPS cells as well as adult stem cells are changing the pace of biomedical research and the translational landscape.

Baseline automotive gas turbine engine development program

NASA Technical Reports Server (NTRS)

Wagner, C. E. (Editor); Pampreen, R. C. (Editor)

1979-01-01

Tests results on a baseline engine are presented to document the automotive gas turbine state-of-the-art at the start of the program. The performance characteristics of the engine and of a vehicle powered by this engine are defined. Component improvement concepts in the baseline engine were evaluated on engine dynamometer tests in the complete vehicle on a chassis dynamometer and on road tests. The concepts included advanced combustors, ceramic regenerators, an integrated control system, low cost turbine material, a continuously variable transmission, power-turbine-driven accessories, power augmentation, and linerless insulation in the engine housing.

Extracting maximum power from active colloidal heat engines

NASA Astrophysics Data System (ADS)

Martin, D.; Nardini, C.; Cates, M. E.; Fodor, É.

2018-03-01

Colloidal heat engines extract power out of a fluctuating bath by manipulating a confined tracer. Considering a self-propelled tracer surrounded by a bath of passive colloids, we optimize the engine performances based on the maximum available power. Our approach relies on an adiabatic mean-field treatment of the bath particles which reduces the many-body description into an effective tracer dynamics. It leads us to reveal that, when operated at constant activity, an engine can only produce less maximum power than its passive counterpart. In contrast, the output power of an isothermal engine, operating with cyclic variations of the self-propulsion without any passive equivalent, exhibits an optimum in terms of confinement and activity. Direct numerical simulations of the microscopic dynamics support the validity of these results even beyond the mean-field regime, with potential relevance to the design of experimental engines.

Teaching Sustainable Energy and Power Electronics to Engineering Students in a Laboratory Environment Using Industry-Standard Tools

ERIC Educational Resources Information Center

Ochs, David S.; Miller, Ruth Douglas

2015-01-01

Power electronics and renewable energy are two important topics for today's power engineering students. In many cases, the two topics are inextricably intertwined. As the renewable energy sector grows, the need for engineers qualified to design such systems grows as well. In order to train such engineers, new courses are needed that highlight the…

Solar energetic particle events in different types of solar wind

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kahler, S. W.; Vourlidas, A., E-mail: stephen.kahler@kirtland.af.mil

2014-08-10

We examine statistically some properties of 96 20 MeV gradual solar energetic proton (SEP) events as a function of three different types of solar wind (SW) as classified by Richardson and Cane. Gradual SEP (E > 10 MeV) events are produced in shocks driven by fast (V ≳ 900 km s{sup –1}) and wide (W > 60°) coronal mass ejections (CMEs). We find no differences among the transient, fast, and slow SW streams for SEP 20 MeV proton event timescales. It has recently been found that the peak intensities Ip of these SEP events scale with the ∼2 MeV protonmore » background intensities, which may be a proxy for the near-Sun shock seed particles. Both the intensities Ip and their 2 MeV backgrounds are significantly enhanced in transient SW compared to those of fast and slow SW streams, and the values of Ip normalized to the 2 MeV backgrounds only weakly correlate with CME V for all SW types. This result implies that forecasts of SEP events could be improved by monitoring both the Sun and the local SW stream properties and that the well known power-law size distributions of Ip may differ between transient and long-lived SW streams. We interpret an observed correlation between CME V and the 2 MeV background for SEP events in transient SW as a manifestation of enhanced solar activity.« less

Effect of dopaminergic drugs on the reserpine-induced lowering of hippocampal theta wave frequency in rats.

PubMed

Nakagawa, T; Ukai, K; Ohyama, T; Gomita, Y; Okamura, H

2000-05-01

The effects of dopaminergic drugs on the lowering of hippocampal theta wave frequency induced by reserpine 1 mg/kg s.c. were examined. Sibutramine (monoamine reuptake inhibitor) 10 mg/kg p.o., methamphetamine (monoamine releaser) 1 mg/kg, quinpirole (dopamine D2 receptor agonist) 10 mg/kg i.p., and SKF 38393 (dopamine D1 receptor agonist) 10 mg/kg i.p. each antagonized the reserpine-induced lowering of hippocampal theta wave frequency in rats. Moreover, the combined administration of SKF 38393 1 mg/kg i.p. and quinpirole 1 mg/kg i.p. synergistically antagonized a reserpine-induced lowering of this frequency. Dosulepin, amitriptyline, and desipramine, which are weak inhibitors of dopamine reuptake, each had little effect on the reserpine-induced lowering of theta wave frequency at a dose of 40 mg/kg p.o. Furthermore, atropine (muscarinic anticholinergic drug) 20 mg/kg p.o. decreased theta wave power in the low-frequency range following a shift to the lower range by reserpine. A positive correlation was observed for each of the above drugs between a reversal of reserpine-induced lowering of theta wave frequency and a reversal of impairment of reserpine-induced conditioned avoidance responses (ACAR) in rats. These results suggest that the reserpine-induced lowering of hippocampal theta wave frequency plays a role in the impairment of reserpine-induced ACAR, and that dopamine D1 and D2 receptors play important roles in antagonizing this lowering of frequency.

FPGA-based RF spectrum merging and adaptive hopset selection

NASA Astrophysics Data System (ADS)

McLean, R. K.; Flatley, B. N.; Silvius, M. D.; Hopkinson, K. M.

The radio frequency (RF) spectrum is a limited resource. Spectrum allotment disputes stem from this scarcity as many radio devices are confined to a fixed frequency or frequency sequence. One alternative is to incorporate cognition within a reconfigurable radio platform, therefore enabling the radio to adapt to dynamic RF spectrum environments. In this way, the radio is able to actively sense the RF spectrum, decide, and act accordingly, thereby sharing the spectrum and operating in more flexible manner. In this paper, we present a novel solution for merging many distributed RF spectrum maps into one map and for subsequently creating an adaptive hopset. We also provide an example of our system in operation, the result of which is a pseudorandom adaptive hopset. The paper then presents a novel hardware design for the frequency merger and adaptive hopset selector, both of which are written in VHDL and implemented as a custom IP core on an FPGA-based embedded system using the Xilinx Embedded Development Kit (EDK) software tool. The design of the custom IP core is optimized for area, and it can process a high-volume digital input via a low-latency circuit architecture. The complete embedded system includes the Xilinx PowerPC microprocessor, UART serial connection, and compact flash memory card IP cores, and our custom map merging/hopset selection IP core, all of which are targeted to the Virtex IV FPGA. This system is then incorporated into a cognitive radio prototype on a Rice University Wireless Open Access Research Platform (WARP) reconfigurable radio.

Plasma current start-up using the lower hybrid wave on the TST-2 spherical tokamak

NASA Astrophysics Data System (ADS)

Takase, Y.; Ejiri, A.; Inada, T.; Moeller, C. P.; Shinya, T.; Tsujii, N.; Yajima, S.; Furui, H.; Homma, H.; Imamura, K.; Nakamura, K.; Nakamura, K.; Sonehara, M.; Takeuchi, T.; Togashi, H.; Tsuda, S.; Yoshida, Y.

2015-12-01

Non-inductive plasma current start-up, ramp-up and sustainment by waves in the lower hybrid wave (LHW) frequency range at 200 MHz were investigated on the TST-2 spherical tokamak (R0 ≤ 0.38 m, a ≤ 0.25 m, Bt0 ≤ 0.3T, Ip ≤ 0.14 MA). Experimental results obtained using three types of antenna were compared. Both the highest plasma current (Ip = 18 kA) and the highest current drive figure of merit ηCD≡n¯eIpR0/PRF=1.4 ×1017 A/W/m2 were achieved using the capacitively-coupled combline (CCC) antenna, designed to excite the LHW with a sharp and highly directional wavenumber spectrum. For Ip greater than about 5 kA, high energy electrons accelerated by the LHW become the dominant carrier of plasma current. The low value of ηCD observed so far are believed to be caused by a rapid loss of energetic electrons and parasitic losses of the LHW energy in the plasma periphery. ηCD is expected to improve by an order of magnitude by increasing the plasma current to improve energetic electron confinement. In addition, edge power losses are expected to be reduced by increasing the toroidal magnetic field to improve wave accessibility to the plasma core, and by launching the LHW from the inboard upper region of the torus to achieve better single-pass absorption.

Underwater striling engine design with modified one-dimensional model

NASA Astrophysics Data System (ADS)

Li, Daijin; Qin, Kan; Luo, Kai

2015-09-01

Stirling engines are regarded as an efficient and promising power system for underwater devices. Currently, many researches on one-dimensional model is used to evaluate thermodynamic performance of Stirling engine, but in which there are still some aspects which cannot be modeled with proper mathematical models such as mechanical loss or auxiliary power. In this paper, a four-cylinder double-acting Stirling engine for Unmanned Underwater Vehicles (UUVs) is discussed. And a one-dimensional model incorporated with empirical equations of mechanical loss and auxiliary power obtained from experiments is derived while referring to the Stirling engine computer model of National Aeronautics and Space Administration (NASA). The P-40 Stirling engine with sufficient testing results from NASA is utilized to validate the accuracy of this one-dimensional model. It shows that the maximum error of output power of theoretical analysis results is less than 18% over testing results, and the maximum error of input power is no more than 9%. Finally, a Stirling engine for UUVs is designed with Schmidt analysis method and the modified one-dimensional model, and the results indicate this designed engine is capable of showing desired output power.

Nuclear Engineering Technologists in the Nuclear Power Era

ERIC Educational Resources Information Center

Wang, C. H.; And Others

1974-01-01

Describes manpower needs in nuclear engineering in the areas of research and development, architectural engineering and construction supervision, power reactor operations, and regulatory tasks. Outlines a suitable curriculum to prepare students for the tasks related to construction and operation of power reactors. (GS)

14 CFR 121.185 - Airplanes: Reciprocating engine-powered: Landing limitations: Destination airport.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Reciprocating engine-powered...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.185 Airplanes: Reciprocating engine-powered: Landing limitations...

14 CFR 121.185 - Airplanes: Reciprocating engine-powered: Landing limitations: Destination airport.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Reciprocating engine-powered...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.185 Airplanes: Reciprocating engine-powered: Landing limitations...

14 CFR 121.185 - Airplanes: Reciprocating engine-powered: Landing limitations: Destination airport.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Reciprocating engine-powered...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.185 Airplanes: Reciprocating engine-powered: Landing limitations...

14 CFR 121.187 - Airplanes: Reciprocating engine-powered: Landing limitations: Alternate airport.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Reciprocating engine-powered...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.187 Airplanes: Reciprocating engine-powered: Landing limitations...

14 CFR 121.185 - Airplanes: Reciprocating engine-powered: Landing limitations: Destination airport.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Reciprocating engine-powered...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.185 Airplanes: Reciprocating engine-powered: Landing limitations...

14 CFR 121.187 - Airplanes: Reciprocating engine-powered: Landing limitations: Alternate airport.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Reciprocating engine-powered...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.187 Airplanes: Reciprocating engine-powered: Landing limitations...

14 CFR 121.187 - Airplanes: Reciprocating engine-powered: Landing limitations: Alternate airport.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Reciprocating engine-powered...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.187 Airplanes: Reciprocating engine-powered: Landing limitations...

14 CFR 121.187 - Airplanes: Reciprocating engine-powered: Landing limitations: Alternate airport.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Reciprocating engine-powered...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.187 Airplanes: Reciprocating engine-powered: Landing limitations...

14 CFR 121.187 - Airplanes: Reciprocating engine-powered: Landing limitations: Alternate airport.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Reciprocating engine-powered...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.187 Airplanes: Reciprocating engine-powered: Landing limitations...

Applicability of advanced automotive heat engines to solar thermal power

NASA Technical Reports Server (NTRS)

Beremand, D. G.; Evans, D. G.; Alger, D. L.

1981-01-01

The requirements of a solar thermal power system are reviewed and compared with the predicted characteristics of automobile engines under development. A good match is found in terms of power level and efficiency when the automobile engines, designed for maximum powers of 65-100 kW (87 to 133 hp) are operated to the nominal 20-40 kW electric output requirement of the solar thermal application. At these reduced power levels it appears that the automotive gas turbine and Stirling engines have the potential to deliver the 40+ percent efficiency goal of the solar thermal program.

Applicability of advanced automotive heat engines to solar thermal power

NASA Astrophysics Data System (ADS)

Beremand, D. G.; Evans, D. G.; Alger, D. L.

The requirements of a solar thermal power system are reviewed and compared with the predicted characteristics of automobile engines under development. A good match is found in terms of power level and efficiency when the automobile engines, designed for maximum powers of 65-100 kW (87 to 133 hp) are operated to the nominal 20-40 kW electric output requirement of the solar thermal application. At these reduced power levels it appears that the automotive gas turbine and Stirling engines have the potential to deliver the 40+ percent efficiency goal of the solar thermal program.

Single Phase Passive Rectification Versus Active Rectification Applied to High Power Stirling Engines

NASA Technical Reports Server (NTRS)

Santiago, Walter; Birchenough, Arthur G.

2006-01-01

Stirling engine converters are being considered as potential candidates for high power energy conversion systems required by future NASA explorations missions. These types of engines typically contain two major moving parts, the displacer and the piston, in which a linear alternator is attached to the piston to produce a single phase sinusoidal waveform at a specific electric frequency. Since all Stirling engines perform at low electrical frequencies (less or equal to 100 Hz), space explorations missions that will employ these engines will be required to use DC power management and distribution (PMAD) system instead of an AC PMAD system to save on space and weight. Therefore, to supply such DC power an AC to DC converter is connected to the Stirling engine. There are two types of AC to DC converters that can be employed, a passive full bridge diode rectifier and an active switching full bridge rectifier. Due to the inherent line inductance of the Stirling Engine-Linear Alternator (SE-LA), their sinusoidal voltage and current will be phase shifted producing a power factor below 1. In order to keep power the factor close to unity, both AC to DC converters topologies will implement power factor correction. This paper discusses these power factor correction methods as well as their impact on overall mass for exploration applications. Simulation results on both AC to DC converters topologies with power factor correction as a function of output power and SE-LA line inductance impedance are presented and compared.

Powertrain with powersplit pump input and method of use thereof

DOEpatents

Johnson, Kris W.; Rose, Charles E.

2009-04-28

A powertrain includes an engine operatively connected to a primary power consuming device to transmit power thereto. The powertrain also includes a motor and a pump. The power output of the motor is independent of the power output of the engine. An epicyclic geartrain includes first, second and third members. The first member is operatively connected to the engine to receive power therefrom. The second member is operatively connected to the motor to receive power therefrom. The third member is operatively connected to the pump to transmit power thereto.

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant. Conceptual Design Engineering Report (CDER). Volume 2: Engineering. Volume 3: Costs and schedules

NASA Astrophysics Data System (ADS)

1981-09-01

Engineering design details for the principal systems, system operating modes, site facilities, and structures of an engineering test facility (ETF) of a 200 MWE power plant are presented. The ETF resembles a coal-fired steam power plant in many ways. It is analogous to a conventional plant which has had the coal combustor replaced with the MHD power train. Most of the ETF components are conventional. They can, however, be sized or configured differently or perform additional functions from those in a conventional coal power plant. The boiler not only generates steam, but also performs the functions of heating the MHD oxidant, recovering seed, and controlling emissions.

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant. Conceptual Design Engineering Report (CDER). Volume 2: Engineering. Volume 3: Costs and schedules

NASA Technical Reports Server (NTRS)

1981-01-01

Engineering design details for the principal systems, system operating modes, site facilities, and structures of an engineering test facility (ETF) of a 200 MWE power plant are presented. The ETF resembles a coal-fired steam power plant in many ways. It is analogous to a conventional plant which has had the coal combustor replaced with the MHD power train. Most of the ETF components are conventional. They can, however, be sized or configured differently or perform additional functions from those in a conventional coal power plant. The boiler not only generates steam, but also performs the functions of heating the MHD oxidant, recovering seed, and controlling emissions.

Prediction of the Main Engine Power of a New Container Ship at the Preliminary Design Stage

NASA Astrophysics Data System (ADS)

Cepowski, Tomasz

2017-06-01

The paper presents mathematical relationships that allow us to forecast the estimated main engine power of new container ships, based on data concerning vessels built in 2005-2015. The presented approximations allow us to estimate the engine power based on the length between perpendiculars and the number of containers the ship will carry. The approximations were developed using simple linear regression and multivariate linear regression analysis. The presented relations have practical application for estimation of container ship engine power needed in preliminary parametric design of the ship. It follows from the above that the use of multiple linear regression to predict the main engine power of a container ship brings more accurate solutions than simple linear regression.

14 CFR 121.197 - Airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Turbine engine powered: Landing... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.197 Airplanes: Turbine engine powered: Landing limitations: Alternate...

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Turbine engine powered: Takeoff... OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a...

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Turbine engine powered: Takeoff... OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a...

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Turbine engine powered: Takeoff... OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a...

14 CFR 121.195 - Airplanes: Turbine engine powered: Landing limitations: Destination airports.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Turbine engine powered: Landing...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.195 Airplanes: Turbine engine powered: Landing limitations...

14 CFR 121.197 - Airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Turbine engine powered: Landing... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.197 Airplanes: Turbine engine powered: Landing limitations: Alternate...

14 CFR 121.195 - Airplanes: Turbine engine powered: Landing limitations: Destination airports.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Turbine engine powered: Landing...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.195 Airplanes: Turbine engine powered: Landing limitations...

14 CFR 121.195 - Airplanes: Turbine engine powered: Landing limitations: Destination airports.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Turbine engine powered: Landing...: CERTIFICATION AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.195 Airplanes: Turbine engine powered: Landing limitations...

14 CFR 121.197 - Airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Turbine engine powered: Landing... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.197 Airplanes: Turbine engine powered: Landing limitations: Alternate...

14 CFR 23.49 - Stalling period.

Code of Federal Regulations, 2010 CFR

2010-01-01

... which the airplane is controllable with— (1) For reciprocating engine-powered airplanes, the engine(s... more than 110 percent of the stalling speed; (2) For turbine engine-powered airplanes, the propulsive..., VSOand VS1at maximum weight must not exceed 61 knots for— (1) Single-engine airplanes; and (2...

Performance Evaluation of Diesel Engine with Preheated Bio Diesel with Additives

NASA Astrophysics Data System (ADS)

Ram Vajja, Sai; Murali, R. B. V.

2016-09-01

This paper mainly reviews about the usage of preheated bio diesel added with 0.5% Etchant as an alternative fuel and evaluates its performance for various blends with different loads. Bio diesel is added with Etchant for rapid combustion as for the bio diesel, the cetane number is high that results in shorter delay of ignition and the mixture is preheated to raise its temperature to improve the combustion process. Analysis of the parameters required to define the combustion characteristics such as IP, BP, ηbth, ηm, ISFC, BSFC, IMEP, MFC, Exhaust Gas Temperature, Heat Release and heat balance is necessary as these values are significant to assess the performance of engine and its emissions of preheated bio diesel.

Underwater Facilities Inspections and Assessments at Philadelphia Naval Shipyard, Philadelphia, Pennsylvania. Volume 1.

DTIC Science & Technology

1983-10-01

NAVAL FACILITIES ENGINEERING COMMAND~ CORPORATION .𔃾CN C 33 pItLAOFLPHI* NAVAL SH4IP-110 PŕiIL -~~NA IA I 1OAQ 4C-14723, C-13041o, C- 13047 4C-1~3046...5ECTION 2 4 8 10 ATI i I 70 30 0 .50SCALE OF FEET GOAHI FCALE CHESAPEAKE DIVISION GRAPIC SALENAVAL FACILITIES ENGINEERING COMMAND C-DLS E.GINEERING...ELEVATION CORE LCC- ATI ~J 45+00 444-50 44+00 493+50 loyo OF V 1 11 FILE’ NV~ 45+0(o / 10 5TA � TIMBER 51NEETIW4& BATTER FILI c 0 - r, - Q Q -Q Q Q -Q- ’~ rP

PolyaPeak: Detecting Transcription Factor Binding Sites from ChIP-seq Using Peak Shape Information

PubMed Central

Wu, Hao; Ji, Hongkai

2014-01-01

ChIP-seq is a powerful technology for detecting genomic regions where a protein of interest interacts with DNA. ChIP-seq data for mapping transcription factor binding sites (TFBSs) have a characteristic pattern: around each binding site, sequence reads aligned to the forward and reverse strands of the reference genome form two separate peaks shifted away from each other, and the true binding site is located in between these two peaks. While it has been shown previously that the accuracy and resolution of binding site detection can be improved by modeling the pattern, efficient methods are unavailable to fully utilize that information in TFBS detection procedure. We present PolyaPeak, a new method to improve TFBS detection by incorporating the peak shape information. PolyaPeak describes peak shapes using a flexible Pólya model. The shapes are automatically learnt from the data using Minorization-Maximization (MM) algorithm, then integrated with the read count information via a hierarchical model to distinguish true binding sites from background noises. Extensive real data analyses show that PolyaPeak is capable of robustly improving TFBS detection compared with existing methods. An R package is freely available. PMID:24608116

Innovative polymeric system (IPS) for solvent-free lipophilic drug transdermal delivery via dissolving microneedles.

PubMed

Dangol, Manita; Yang, Huisuk; Li, Cheng Guo; Lahiji, Shayan Fakhraei; Kim, Suyong; Ma, Yonghao; Jung, Hyungil

2016-02-10

Lipophilic drugs are potential drug candidates during drug development. However, due to the need for hazardous organic solvents for their solubilization, these drugs often fail to reach the pharmaceutical market, and in doing so highlight the importance of solvent free systems. Although transdermal drug delivery systems (TDDSs) are considered prospective safe drug delivery routes, a system involving lipophilic drugs in solvent free or powder form has not yet been described. Here, we report, for the first time, a novel approach for the delivery of every kind of lipophilic drug in powder form based on an innovative polymeric system (IPS). The phase transition of powder form of lipophilic drugs due to interior chemical bonds between drugs and biodegradable polymers and formation of nano-sized colloidal structures allowed the fabrication of dissolving microneedles (DMNs) to generate a powerful TDDS. We showed that IPS based DMN with powder capsaicin enhances the therapeutic effect for treatment of the rheumatic arthritis in a DBA/1 mouse model compared to a solvent-based system, indicating the promising potential of this new solvent-free platform for lipophilic drug delivery. Copyright © 2016 Elsevier B.V. All rights reserved.

Molecular simulation of small Knudsen number flows

NASA Astrophysics Data System (ADS)

Fei, Fei; Fan, Jing

2012-11-01

The direct simulation Monte Carlo (DSMC) method is a powerful particle-based method for modeling gas flows. It works well for relatively large Knudsen (Kn) numbers, typically larger than 0.01, but quickly becomes computationally intensive as Kn decreases due to its time step and cell size limitations. An alternative approach was proposed to relax or remove these limitations, based on replacing pairwise collisions with a stochastic model corresponding to the Fokker-Planck equation [J. Comput. Phys., 229, 1077 (2010); J. Fluid Mech., 680, 574 (2011)]. Similar to the DSMC method, the downside of that approach suffers from computationally statistical noise. To solve the problem, a diffusion-based information preservation (D-IP) method has been developed. The main idea is to track the motion of a simulated molecule from the diffusive standpoint, and obtain the flow velocity and temperature through sampling and averaging the IP quantities. To validate the idea and the corresponding model, several benchmark problems with Kn ˜ 10-3-10-4 have been investigated. It is shown that the IP calculations are not only accurate, but also efficient because they make possible using a time step and cell size over an order of magnitude larger than the mean collision time and mean free path, respectively.

Robust technique using an imaging plate to detect environmental radioactivity.

PubMed

Isobe, Tomonori; Mori, Yutaro; Takada, Kenta; Sato, Eisuke; Sakurai, Hideyuki; Sakae, Takeji

2013-04-01

The Fukushima Daiichi Nuclear Power Plant was severely damaged by the Great East Japan Earthquake on 11 March 2011. Consequently, a large amount of radioactive material was accidentally released. Recently, the focus has been on quantification of environmental radioactive material. However, conventional techniques require complicated and expensive measurement equipment. In this research, the authors developed a simple method to detect environmental radioactive material with an imaging plate (IP). Two specific measurement subjects were targeted: measurements for the depth distribution of radioactive material in soil and surface contamination of a building roof. For the measurement of depth distribution of radioactive material in soil, the authors ascertained that the concentration of environmental radioactivity was highest at 5 cm below the surface, and it decreased with depth. For the measurement of surface contamination of the building roof, the authors created a contamination map of the building roof. The detector developed could contact the ground directly, and unlike other survey meters, it was not influenced by peripheral radioactivity. In this study, the authors verified the feasibility of measurement of environmental radioactivity with an IP. Although the measured values of the IP were relative, further work is planned to perform evaluations of absolute quantities of radioactive material.

Identification of Predictive Cis-Regulatory Elements Using a Discriminative Objective Function and a Dynamic Search Space

PubMed Central

Karnik, Rahul; Beer, Michael A.

2015-01-01

The generation of genomic binding or accessibility data from massively parallel sequencing technologies such as ChIP-seq and DNase-seq continues to accelerate. Yet state-of-the-art computational approaches for the identification of DNA binding motifs often yield motifs of weak predictive power. Here we present a novel computational algorithm called MotifSpec, designed to find predictive motifs, in contrast to over-represented sequence elements. The key distinguishing feature of this algorithm is that it uses a dynamic search space and a learned threshold to find discriminative motifs in combination with the modeling of motifs using a full PWM (position weight matrix) rather than k-mer words or regular expressions. We demonstrate that our approach finds motifs corresponding to known binding specificities in several mammalian ChIP-seq datasets, and that our PWMs classify the ChIP-seq signals with accuracy comparable to, or marginally better than motifs from the best existing algorithms. In other datasets, our algorithm identifies novel motifs where other methods fail. Finally, we apply this algorithm to detect motifs from expression datasets in C. elegans using a dynamic expression similarity metric rather than fixed expression clusters, and find novel predictive motifs. PMID:26465884

Identification of Predictive Cis-Regulatory Elements Using a Discriminative Objective Function and a Dynamic Search Space.

PubMed

Karnik, Rahul; Beer, Michael A

2015-01-01

The generation of genomic binding or accessibility data from massively parallel sequencing technologies such as ChIP-seq and DNase-seq continues to accelerate. Yet state-of-the-art computational approaches for the identification of DNA binding motifs often yield motifs of weak predictive power. Here we present a novel computational algorithm called MotifSpec, designed to find predictive motifs, in contrast to over-represented sequence elements. The key distinguishing feature of this algorithm is that it uses a dynamic search space and a learned threshold to find discriminative motifs in combination with the modeling of motifs using a full PWM (position weight matrix) rather than k-mer words or regular expressions. We demonstrate that our approach finds motifs corresponding to known binding specificities in several mammalian ChIP-seq datasets, and that our PWMs classify the ChIP-seq signals with accuracy comparable to, or marginally better than motifs from the best existing algorithms. In other datasets, our algorithm identifies novel motifs where other methods fail. Finally, we apply this algorithm to detect motifs from expression datasets in C. elegans using a dynamic expression similarity metric rather than fixed expression clusters, and find novel predictive motifs.

First results of coupled IPS/NIMROD/GENRAY simulations

NASA Astrophysics Data System (ADS)

Jenkins, Thomas; Kruger, S. E.; Held, E. D.; Harvey, R. W.; Elwasif, W. R.; Schnack, D. D.

2010-11-01

The Integrated Plasma Simulator (IPS) framework, developed by the SWIM Project Team, facilitates self-consistent simulations of complicated plasma behavior via the coupling of various codes modeling different spatial/temporal scales in the plasma. Here, we apply this capability to investigate the stabilization of tearing modes by ECCD. Under IPS control, the NIMROD code (MHD) evolves fluid equations to model bulk plasma behavior, while the GENRAY code (RF) calculates the self-consistent propagation and deposition of RF power in the resulting plasma profiles. GENRAY data is then used to construct moments of the quasilinear diffusion tensor (induced by the RF) which influence the dynamics of momentum/energy evolution in NIMROD's equations. We present initial results from these coupled simulations and demonstrate that they correctly capture the physics of magnetic island stabilization [Jenkins et al, PoP 17, 012502 (2010)] in the low-beta limit. We also discuss the process of code verification in these simulations, demonstrating good agreement between NIMROD and GENRAY predictions for the flux-surface-averaged, RF-induced currents. An overview of ongoing model development (synthetic diagnostics/plasma control systems; neoclassical effects; etc.) is also presented. Funded by US DoE.

Control logic for exhaust gas driven turbocharger

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adeff, G.A.

1991-12-31

This patent describes a method of controlling an exhaust gas driven turbocharger supplying charge air for an internal combustion engine powering vehicle, the turbocharger being adjustable from a normal mode to a power mode in which the charge air available to the engine during vehicle acceleration is increased over that available when the turbocharger is in the normal mode, the vehicle including engine power control means switchable by the vehicle operator from a normal mode to a power mode so that the vehicle operator may selectively elect either the normal mode or the power mode, comprising the steps of measuringmore » the speed of the vehicle, permitting the vehicle operator to elect either the power mode or the normal mode for a subsequent vehicle acceleration, and then adjusting the turbocharger to the power mode when the speed of the vehicle is less than a predetermined reference speed and the vehicle operator has elected to power mode to increase the charge air available to the engine and thereby increasing engine power on a subsequent acceleration of the vehicle.« less

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XVIII, I--UNDERSTAND ENGINE GEARS AND GEARING PRINCIPLES, II--MACK INTER-AXLE POWER DIVIDER.

ERIC Educational Resources Information Center

Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF DIESEL ENGINE GEARS AND GEARING PRINCIPLES AND THE OPERATING PRINCIPLES AND MAINTENANCE OF POWER DIVIDERS (GEAR BOXES) USED IN DIESEL ENGINE POWER TRANSMISSION. TOPICS ARE (1) THE PURPOSE OF THE ENGINE GEARS, (2) INSPECTING FOR GEAR FAILURES, (3) INSPECTING FOR SHAFT…

The effect of humidity on engine power at altitude

NASA Technical Reports Server (NTRS)

Brooks, D G; Garlock, E A

1933-01-01

From tests made in the altitude chamber of the Bureau of Standards, it was found that the effect of humidity on engine power is the same at altitudes up to 25,000 feet as at sea level. Earlier tests on automotive engines, made under sea-level conditions, showed that water vapor acts as an inert diluent, reducing engine power in proportion to the amount of vapor present. By combining the effects of atmospheric pressure, temperature, and humidity, it is shown that the indicated power obtainable from an engine is proportional to its mass rate of consumption of oxygen. This has led the National Advisory Committee for Aeronautics to adopt a standard basis for the correction of engine performance, in which the effect of humidity is included.

Palm Power Free-Piston Stirling Engine Control Electronics

NASA Astrophysics Data System (ADS)

Keiter, Douglas E.; Holliday, Ezekiel

2007-01-01

A prototype 35We, JP-8 fueled, soldier-wearable power system for the DARPA Palm Power program has been developed and tested by Sunpower. A hermetically-sealed 42We Sunpower Free-Piston Stirling Engine (FPSE) with integral linear alternator is the prime mover for this system. To maximize system efficiency over a broad range of output power, a non-dissipative, highly efficient electronic control system which modulates engine output power by varying piston stroke and converts the AC output voltage of the FPSE into 28Vdc for the Palm Power end user, has been designed and demonstrated as an integral component of the Palm Power system. This paper reviews the current status and progress made in developing the control electronics for the Palm Power system, in addition to describing the operation and demonstrated performance of the engine controller in the context of the current JP-8 fueled Palm Power system.

Comparison of advanced engines for parabolic dish solar thermal power plants

NASA Technical Reports Server (NTRS)

Fujita, T.; Bowyer, J. M.; Gajanana, B. C.

1980-01-01

A paraboloidal dish solar thermal power plant produces electrical energy by a two-step conversion process. The collector subsystem is composed of a two-axis tracking paraboloidal concentrator and a cavity receiver. The concentrator focuses intercepted sunlight (direct, normal insolation) into a cavity receiver whose aperture encircles the focal point of the concentrator. At the internal wall of the receiver the electromagnetic radiation is converted to thermal energy. A heat engine/generator assembly then converts the thermal energy captured by the receiver to electricity. Developmental activity has been concentrated on small power modules which employ 11- to 12-meter diameter dishes to generate nominal power levels of approximately 20 kWe. A comparison of advanced heat engines for the dish power module is presented in terms of the performance potential of each engine with its requirements for advanced technology development. Three advanced engine possibilities are the Brayton (gas turbine), Brayton/Rankine combined cycle, and Stirling engines.

14 CFR 135.373 - Part 25 transport category airplanes with four or more engines: Reciprocating engine powered: En...

Code of Federal Regulations, 2010 CFR

2010-01-01

... four or more engines: Reciprocating engine powered: En route limitations: Two engines inoperative. 135... Airplane Performance Operating Limitations § 135.373 Part 25 transport category airplanes with four or more... operate an airplane certificated under part 25 and having four or more engines unless— (1) There is no...

Automotive Stirling Engine Development Program Mod I Stirling engine development

NASA Technical Reports Server (NTRS)

Simetkosky, M. A.

1983-01-01

The development of the Mod I 4-cylinder automotive Stirling engine is discussed and illustrated with drawings, block diagrams, photographs, and graphs and tables of preliminary test data. The engine and its drive, cold-engine, hot-engine, external-heat, air/fuel, power-control, electronic-control, and auxiliary systems are characterized. Performance results from a total of 1900 h of tests on 4 prototype engines include average maximum efficiency (at 2000 rpm) 34.5 percent and maximum output power 54.4 kW. The modifications introduced in an upgraded version of the Mod I are explained; this engine has maximum efficiency 40.4 percent and maximum power output 69.2 kW.

14 CFR 34.3 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... powered by aircraft gas turbine engines of the classes specified herein and that have U.S. standard...), this FAR applies to civil airplanes that are powered by aircraft gas turbine engines of the classes... EXHAUST EMISSION REQUIREMENTS FOR TURBINE ENGINE POWERED AIRPLANES General Provisions § 34.3 General...

14 CFR 34.3 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... powered by aircraft gas turbine engines of the classes specified herein and that have U.S. standard...), this FAR applies to civil airplanes that are powered by aircraft gas turbine engines of the classes... EXHAUST EMISSION REQUIREMENTS FOR TURBINE ENGINE POWERED AIRPLANES General Provisions § 34.3 General...

Full Hybrid: Passing

Science.gov Websites

Main stage: See through car with battery, engine, generator, power split device, and electric motor the power split device to the front wheels. Main stage: See through car with battery, engine : See through car with battery, engine, generator, power split device, and electric motor visible while

14 CFR 34.3 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... EXHAUST EMISSION REQUIREMENTS FOR TURBINE ENGINE POWERED AIRPLANES General Provisions § 34.3 General... powered by aircraft gas turbine engines of the classes specified herein and that have U.S. standard...), this FAR applies to civil airplanes that are powered by aircraft gas turbine engines of the classes...

40 CFR 1045.140 - What is my engine's maximum engine power?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false What is my engine's maximum engine power? 1045.140 Section 1045.140 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND VESSELS...

40 CFR 1045.140 - What is my engine's maximum engine power?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false What is my engine's maximum engine power? 1045.140 Section 1045.140 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND VESSELS...

40 CFR 1045.140 - What is my engine's maximum engine power?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 33 2011-07-01 2011-07-01 false What is my engine's maximum engine power? 1045.140 Section 1045.140 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND VESSELS...

40 CFR 1045.140 - What is my engine's maximum engine power?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What is my engine's maximum engine power? 1045.140 Section 1045.140 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND VESSELS...

Price Based Local Power Distribution Management System (Local Power Distribution Manager) v1.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

BROWN, RICHARD E.; CZARNECKI, STEPHEN; SPEARS, MICHAEL

2016-11-28

A trans-active energy micro-grid controller is implemented in the VOLTTRON distributed control platform. The system uses the price of electricity as the mechanism for conducting transactions that are used to manage energy use and to balance supply and demand. In order to allow testing and analysis of the control system, the implementation is designed to run completely as a software simulation, while allowing the inclusion of selected hardware that physically manages power. Equipment to be integrated with the micro-grid controller must have an IP (Internet Protocol)-based network connection and a software "driver" must exist to translate data communications between themore » device and the controller.« less

Flight Investigation of Effect of Various Vertical-Tail Modifications on the Directional Stability and Control Characteristics of the P-63A-1 Airplane (AAF No. 42-68889)

NASA Technical Reports Server (NTRS)

Johnson, Harold I.

1946-01-01

Because the results of preliminary flight tests had indicated. the P-63A-1 airplane possessed insufficient directional stability, the NACA and the manufacturer (Bell Aircraft Corporation) suggested three vertical-tail modifications to remedy the deficiencies in the directional characteristics. These modifications included an enlarged vertical tail formed by adding a tip extension to the original vertical tail, a large sharp-edge ventral fin, and a small dorsal fin. The enlarged vertical tail involved only a slight increase in total vertical-tail area from 23.73 to 26.58 square feet but a relatively much larger increase in geometric aspect ratio from 1.24 to 1.73 based on height and area above the horizontal tail. At the request of the Air Material Command, Army Air Forces, flight tests were made to determine the effect of these modifications and of some combinations of these modifications on the directional stability and control characteristics of the airplane, In all, six different vertical-tail. configurations were investigated to determine the lateral and directional oscillation characteristics of the airplane, the sideslip characteristics, the yaw due to ailerons in rudder-fixed rolls from turns and pull-outs, the trim changes due to speed changes; and the trim changes due to power changes. Results of the tests showed that the enlarged vertical tail approximately doubled the directional stability of the airplane and that the pilots considered the directional stability provided by the enlarged vertical tail to be satisfactory. Calculations based on sideslip data obtained at an indicated airspeed of 300 miles per hour showed that the directional stability of the airplane with the original vertical tail corresponded to a value of 0(sub n beta) of -0.00056 whereas for the enlarged vertical tail the estimated va1ue of C(sub n beta) was -0.00130, The ventral fin was found to increase by a moderate amount the directional stability of the airplane with the original vertical tail for smal1 sides1ip angles at low speeds but little consistent change in directional stability was effected by the ventral fin at higher speeds, The effectiveness of the ventral fin was generally much less when used with the enlarged vertical tail than when used with the original vertical tail. The ventral and dorsal fins were found to be very effective in eliminating rudder-force reversals which occurred in low-speed, high-engine-power, sideslipped conditions of flight . Sideslip tests at two altitudes for approximately the sane engine power and indicated airspeed showed that a small decrease in static directional stability occurred with increasing altitude and this decrease in stability was attributed to the increased propeller blade angles required at high altitudes. The variations of rudder pedal force with indicated airspeed using normal rated power and a constant rudder tab setting through the speed range were desirably small for all the configurations tested. The rudder pedal force changed by about 50 pounds for a power change from engine idling power, to normal rated power and this pedal force change was largely independent of airspeed or of vertical-tail configuration for the various configurations tested.

Subtype-selective regulation of IP(3) receptors by thimerosal via cysteine residues within the IP(3)-binding core and suppressor domain.

PubMed

Khan, Samir A; Rossi, Ana M; Riley, Andrew M; Potter, Barry V L; Taylor, Colin W

2013-04-15

IP(3)R (IP(3) [inositol 1,4,5-trisphosphate] receptors) and ryanodine receptors are the most widely expressed intracellular Ca(2+) channels and both are regulated by thiol reagents. In DT40 cells stably expressing single subtypes of mammalian IP(3)R, low concentrations of thimerosal (also known as thiomersal), which oxidizes thiols to form a thiomercurylethyl complex, increased the sensitivity of IP(3)-evoked Ca(2+) release via IP(3)R1 and IP(3)R2, but inhibited IP(3)R3. Activation of IP(3)R is initiated by IP(3) binding to the IBC (IP(3)-binding core; residues 224-604) and proceeds via re-arrangement of an interface between the IBC and SD (suppressor domain; residues 1-223). Thimerosal (100 μM) stimulated IP(3) binding to the isolated NT (N-terminal; residues 1-604) of IP(3)R1 and IP(3)R2, but not to that of IP(3)R3. Binding of a competitive antagonist (heparin) or partial agonist (dimeric-IP(3)) to NT1 was unaffected by thiomersal, suggesting that the effect of thimerosal is specifically related to IP(3)R activation. IP(3) binding to NT1 in which all cysteine residues were replaced by alanine was insensitive to thimerosal, so too were NT1 in which cysteine residues were replaced in either the SD or IBC. This demonstrates that thimerosal interacts directly with cysteine in both the SD and IBC. Chimaeric proteins in which the SD of the IP(3)R was replaced by the structurally related A domain of a ryanodine receptor were functional, but thimerosal inhibited both IP(3) binding to the chimaeric NT and IP(3)-evoked Ca(2+) release from the chimaeric IP(3)R. This is the first systematic analysis of the effects of a thiol reagent on each IP(3)R subtype. We conclude that thimerosal selectively sensitizes IP(3)R1 and IP(3)R2 to IP(3) by modifying cysteine residues within both the SD and IBC and thereby stabilizing an active conformation of the receptor.

Is this the right normalization? A diagnostic tool for ChIP-seq normalization.

PubMed

Angelini, Claudia; Heller, Ruth; Volkinshtein, Rita; Yekutieli, Daniel

2015-05-09

Chip-seq experiments are becoming a standard approach for genome-wide profiling protein-DNA interactions, such as detecting transcription factor binding sites, histone modification marks and RNA Polymerase II occupancy. However, when comparing a ChIP sample versus a control sample, such as Input DNA, normalization procedures have to be applied in order to remove experimental source of biases. Despite the substantial impact that the choice of the normalization method can have on the results of a ChIP-seq data analysis, their assessment is not fully explored in the literature. In particular, there are no diagnostic tools that show whether the applied normalization is indeed appropriate for the data being analyzed. In this work we propose a novel diagnostic tool to examine the appropriateness of the estimated normalization procedure. By plotting the empirical densities of log relative risks in bins of equal read count, along with the estimated normalization constant, after logarithmic transformation, the researcher is able to assess the appropriateness of the estimated normalization constant. We use the diagnostic plot to evaluate the appropriateness of the estimates obtained by CisGenome, NCIS and CCAT on several real data examples. Moreover, we show the impact that the choice of the normalization constant can have on standard tools for peak calling such as MACS or SICER. Finally, we propose a novel procedure for controlling the FDR using sample swapping. This procedure makes use of the estimated normalization constant in order to gain power over the naive choice of constant (used in MACS and SICER), which is the ratio of the total number of reads in the ChIP and Input samples. Linear normalization approaches aim to estimate a scale factor, r, to adjust for different sequencing depths when comparing ChIP versus Input samples. The estimated scaling factor can easily be incorporated in many peak caller algorithms to improve the accuracy of the peak identification. The diagnostic plot proposed in this paper can be used to assess how adequate ChIP/Input normalization constants are, and thus it allows the user to choose the most adequate estimate for the analysis.

Discrimination Between Human Leukocyte Antigen Class I-Bound and Co-Purified HIV-Derived Peptides in Immunopeptidomics Workflows

PubMed Central

Partridge, Thomas; Nicastri, Annalisa; Kliszczak, Anna E.; Yindom, Louis-Marie; Kessler, Benedikt M.; Ternette, Nicola; Borrow, Persephone

2018-01-01

Elucidation of novel peptides presented by human leukocyte antigen (HLA) class I alleles by immunopeptidomics constitutes a powerful approach that can inform the rational design of CD8+ T cell inducing vaccines to control infection with pathogens such as human immunodeficiency virus type 1 (HIV-1) or to combat tumors. Recent advances in the sensitivity of liquid chromatography tandem mass spectrometry instrumentation have facilitated the discovery of thousands of natural HLA-restricted peptides in a single measurement. However, the extent of contamination of class I-bound peptides identified using HLA immunoprecipitation (IP)-based immunopeptidomics approaches with peptides from other sources has not previously been evaluated in depth. Here, we investigated the specificity of the IP-based immunopeptidomics methodology using HLA class I- or II-deficient cell lines and membrane protein-specific antibody IPs. We demonstrate that the 721.221 B lymphoblastoid cell line, widely regarded to be HLA class Ia-deficient, actually expresses and presents peptides on HLA-C*01:02. Using this cell line and the C8166 (HLA class I- and II-expressing) cell line, we show that some HLA class II-bound peptides were co-purified non-specifically during HLA class I and membrane protein IPs. Furthermore, IPs of “irrelevant” membrane proteins from HIV-1-infected HLA class I- and/or II-expressing cells revealed that unusually long HIV-1-derived peptides previously reported by us and other immunopeptidomics studies as potentially novel CD8+ T cell epitopes were non-specifically co-isolated, and so constitute a source of contamination in HLA class I IPs. For example, a 16-mer (FLGKIWPSYKGRPGNF), which was detected in all samples studied represents the full p1 segment of the abundant intracellular or virion-associated proteolytically-processed HIV-1 Gag protein. This result is of importance, as these long co-purified HIV-1 Gag peptides may not elicit CD8+ T cell responses when incorporated into candidate vaccines. These results have wider implications for HLA epitope discovery from abundant or membrane-associated antigens by immunopeptidomics in the context of infectious diseases, cancer, and autoimmunity. PMID:29780384

78 FR 72885 - Information Collections Being Submitted for Review and Approval to the Office of Management and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-04

... toll free service provider, or transfer control of a toll free number from a VRS or IP Relay provider... sections imposed differing requirements on the broadcast and wireless entities, although the issue is the... shall determine operating power by the indirect method (see Sec. 73.51). Upon the completion of the...

Secondary electric power generation with minimum engine bleed

NASA Technical Reports Server (NTRS)

Tagge, G. E.

1983-01-01

Secondary electric power generation with minimum engine bleed is discussed. Present and future jet engine systems are compared. The role of auxiliary power units is evaluated. Details of secondary electric power generation systems with and without auxiliary power units are given. Advanced bleed systems are compared with minimum bleed systems. A cost model of ownership is given. The difference in the cost of ownership between a minimum bleed system and an advanced bleed system is given.

Diesel Engine Waste Heat Recovery Utilizing Electric Turbocompound Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hopman, Ulrich,; Kruiswyk, Richard W.

2005-07-05

Caterpillar's Technology & Solutions Division conceived, designed, built and tested an electric turbocompound system for an on-highway heavy-duty truck engine. The heart of the system is a unique turbochargerr with an electric motor/generator mounted on the shaft between turbine and compressor wheels. When the power produced by the turbocharger turbine exceeds the power of the compressor, the excess power is converted to electrical power by the generator on the turbo shaft; that power is then used to help turn the crankshaft via an electric motor mounted in the engine flywheel housing. The net result is an improvement in engine fuelmore » economy. The electric turbocompound system provides added control flexibility because it is capable of varying the amount of power extracted from the exhaust gases, thus allowing for control of engine boost. The system configuration and design, turbocharger features, control system development, and test results are presented.« less

Hydrocarbon potential of Upper Devonian black shale, eastern Kentucky

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnston, I.M.; Frankie, W.T.; Moody, J.R.

The gas-producing Upper Devonian black shales of eastern Kentucky represent cycles of organic units alternating with less-organic units that were dominated by an influx of clastics from a northeastern source. This pattern of sedimentation is typical throughout the southern Appalachian basin in areas basinal to, yet still influenced by, the Catskill delta to the northwest. These black shales, which thin westward onto the Cincinnati arch, dip eastward into the Appalachian basin. To evaluate the future gas potential of Devonian shale, a data base has been compiled, consisting of specific geologic and engineering information from 5920 Devonian shale wells in Letcher,more » Knott, Floyd, Martin, and Pike Counties, Kentucky. The first successful gas completion in eastern Kentucky was drilled in Martin County in 1901. Comparison of initial open-flow potential (IP) and long-term production data for these wells demonstrates that higher IP values generally indicate wells of higher production potential. Areas of higher IP are aligned linearly, and these lineaments are interpreted to be related to fracture systems within the Devonian shale. These fractures may be basement influenced. Temperature log analyses indicate that the greatest number of natural gas shows occur in the lower Huron Member of the Ohio Shale. Using both the temperature log to indicate gas shows and the gamma-ray log to determine the producing unit is a workable method for selecting the interval for treatment.« less

Automotive Stirling engine system component review

NASA Technical Reports Server (NTRS)

Hindes, Chip; Stotts, Robert

1987-01-01

The design and testing of the power and combustion control system for the basic Stirling engine, Mod II, are examined. The power control system is concerned with transparent operation, and the Mod II uses engine working gas pressure variation to control the power output of the engine. The main components of the power control system, the power control valve, the pump-down system, and the hydrogen stable system, are described. The combustion control system consists of a combustion air supply system and an air/fuel ratio control system, and the system is to maintain constant heater head temperature, and to maximize combustion efficiency and to minimize exhaust emissions.

Process improvement by cycle time reduction through Lean Methodology

NASA Astrophysics Data System (ADS)

Siva, R.; patan, Mahamed naveed khan; lakshmi pavan kumar, Mane; Purusothaman, M.; pitchai, S. Antony; Jegathish, Y.

2017-05-01

In present world, every customer needs their products to get on time with good quality. Presently every industry is striving to satisfy their customer requirements. An aviation concern trying to accomplish continuous improvement in all its projects. In this project the maintenance service for the customer is analyzed. The maintenance part service is split up into four levels. Out of it, three levels are done in service shops and the fourth level falls under customer’s privilege to change the parts in their aircraft engines at their location. An enhancement for electronics initial provisioning (eIP) is done for fourth level. Customers request service shops to get their requirements through Recommended Spare Parts List (RSPL) by eIP. To complete this RSPL for one customer, it takes 61.5 hours as a cycle time which is very high. By mapping current state VSM and takt time, future state improvement can be done in order to reduce cycle time using Lean tools such as Poke-Yoke, Jidoka, 5S, Muda etc.,

Enhanced Differentiation of Human Preosteoblasts on Electrospun Blend Fiber Mats of Polydioxanone and Anionic Sulfated Polysaccharides

PubMed Central

2017-01-01

The viability and differentiation of SaOS-2 preosteoblasts on fiber mats of blends comprising of the biodegradable poly(ester-ether) polydioxanone (PDX) and the sulfate-containing anionic polysaccharides kappa-carrageenan (KCG) and fucoidan (FUC) were investigated for a range of different blend compositions. The detailed analysis of the blend nanofiber properties revealed a different degree of miscibility of PDX and the polysaccharide leading to a different enrichment at the surface of the blend nanofibers, which were observed to be stable in phosphate buffer solution (PBS) for up to 5 weeks. The fibrous mats of PDX/FUC led to the highest osteogenic differentiation with very good cell viability. The electrospun blend fibers also supported human-induced pluripotent stem (iPS) cells and iPS cell-derived embryoid bodies with high cell viability, which underlines the potential of these novel blend fiber systems for optimized performance in bone tissue engineering applications. PMID:29285521

Reconfigurable Hardware Adapts to Changing Mission Demands

NASA Technical Reports Server (NTRS)

2003-01-01

A new class of computing architectures and processing systems, which use reconfigurable hardware, is creating a revolutionary approach to implementing future spacecraft systems. With the increasing complexity of electronic components, engineers must design next-generation spacecraft systems with new technologies in both hardware and software. Derivation Systems, Inc., of Carlsbad, California, has been working through NASA s Small Business Innovation Research (SBIR) program to develop key technologies in reconfigurable computing and Intellectual Property (IP) soft cores. Founded in 1993, Derivation Systems has received several SBIR contracts from NASA s Langley Research Center and the U.S. Department of Defense Air Force Research Laboratories in support of its mission to develop hardware and software for high-assurance systems. Through these contracts, Derivation Systems began developing leading-edge technology in formal verification, embedded Java, and reconfigurable computing for its PF3100, Derivational Reasoning System (DRS ), FormalCORE IP, FormalCORE PCI/32, FormalCORE DES, and LavaCORE Configurable Java Processor, which are designed for greater flexibility and security on all space missions.

Experimental approaches to identify cellular G-quadruplex structures and functions.

PubMed

Di Antonio, Marco; Rodriguez, Raphaël; Balasubramanian, Shankar

2012-05-01

Guanine-rich nucleic acids can fold into non-canonical DNA secondary structures called G-quadruplexes. The formation of these structures can interfere with the biology that is crucial to sustain cellular homeostases and metabolism via mechanisms that include transcription, translation, splicing, telomere maintenance and DNA recombination. Thus, due to their implication in several biological processes and possible role promoting genomic instability, G-quadruplex forming sequences have emerged as potential therapeutic targets. There has been a growing interest in the development of synthetic molecules and biomolecules for sensing G-quadruplex structures in cellular DNA. In this review, we summarise and discuss recent methods developed for cellular imaging of G-quadruplexes, and the application of experimental genomic approaches to detect G-quadruplexes throughout genomic DNA. In particular, we will discuss the use of engineered small molecules and natural proteins to enable pull-down, ChIP-Seq, ChIP-chip and fluorescence imaging of G-quadruplex structures in cellular DNA. Copyright © 2012 Elsevier Inc. All rights reserved.

14 CFR 135.387 - Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Large transport category airplanes: Turbine....387 Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate... alternate airport for a turbine engine powered large transport category airplane unless (based on the...

14 CFR 135.385 - Large transport category airplanes: Turbine engine powered: Landing limitations: Destination...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Large transport category airplanes: Turbine....385 Large transport category airplanes: Turbine engine powered: Landing limitations: Destination airports. (a) No person operating a turbine engine powered large transport category airplane may take off...

14 CFR 135.385 - Large transport category airplanes: Turbine engine powered: Landing limitations: Destination...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Large transport category airplanes: Turbine....385 Large transport category airplanes: Turbine engine powered: Landing limitations: Destination airports. (a) No person operating a turbine engine powered large transport category airplane may take off...

14 CFR 135.387 - Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Large transport category airplanes: Turbine....387 Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate... alternate airport for a turbine engine powered large transport category airplane unless (based on the...

14 CFR 135.387 - Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate airports.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Large transport category airplanes: Turbine....387 Large transport category airplanes: Turbine engine powered: Landing limitations: Alternate... alternate airport for a turbine engine powered large transport category airplane unless (based on the...

14 CFR 135.385 - Large transport category airplanes: Turbine engine powered: Landing limitations: Destination...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Large transport category airplanes: Turbine....385 Large transport category airplanes: Turbine engine powered: Landing limitations: Destination airports. (a) No person operating a turbine engine powered large transport category airplane may take off...

14 CFR 23.1045 - Cooling test procedures for turbine engine powered airplanes.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Cooling test procedures for turbine engine powered airplanes. 23.1045 Section 23.1045 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... CATEGORY AIRPLANES Powerplant Cooling § 23.1045 Cooling test procedures for turbine engine powered...

14 CFR 23.1045 - Cooling test procedures for turbine engine powered airplanes.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Cooling test procedures for turbine engine powered airplanes. 23.1045 Section 23.1045 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... CATEGORY AIRPLANES Powerplant Cooling § 23.1045 Cooling test procedures for turbine engine powered...

40 CFR 1042.830 - Labeling.

Code of Federal Regulations, 2011 CFR

2011-07-01

... family. (4) State the engine's category, displacement (in liters or L/cyl), maximum engine power (in kW... may specify displacement, maximum engine power, and power density as ranges consistent with the ranges listed in § 1042.101. See § 1042.140 for descriptions of how to specify per-cylinder displacement...

40 CFR 1042.830 - Labeling.

Code of Federal Regulations, 2014 CFR

2014-07-01

... family. (4) State the engine's category, displacement (in liters or L/cyl), maximum engine power (in kW... may specify displacement, maximum engine power, and power density as ranges consistent with the ranges listed in § 1042.101. See § 1042.140 for descriptions of how to specify per-cylinder displacement...

40 CFR 1042.830 - Labeling.

Code of Federal Regulations, 2013 CFR

2013-07-01

... family. (4) State the engine's category, displacement (in liters or L/cyl), maximum engine power (in kW... may specify displacement, maximum engine power, and power density as ranges consistent with the ranges listed in § 1042.101. See § 1042.140 for descriptions of how to specify per-cylinder displacement...

40 CFR 1042.830 - Labeling.

Code of Federal Regulations, 2010 CFR

2010-07-01

... family. (4) State the engine's category, displacement (in liters or L/cyl), maximum engine power (in kW... may specify displacement, maximum engine power, and power density as ranges consistent with the ranges listed in § 1042.101. See § 1042.140 for descriptions of how to specify per-cylinder displacement...

40 CFR 1042.830 - Labeling.

Code of Federal Regulations, 2012 CFR

2012-07-01

... family. (4) State the engine's category, displacement (in liters or L/cyl), maximum engine power (in kW... may specify displacement, maximum engine power, and power density as ranges consistent with the ranges listed in § 1042.101. See § 1042.140 for descriptions of how to specify per-cylinder displacement...

F1 style MGU-H applied to the turbocharger of a gasoline hybrid electric passenger car

NASA Astrophysics Data System (ADS)

Boretti, Albert

2017-12-01

We consider a turbocharged gasoline direct injection (DI) engine featuring a motor-generator-unit (MGU-H) fitted on the turbocharger shaft. The MGU-H receives or delivers energy to the same energy storage (ES) of the hybrid power unit that comprises a motor-generator unit on the driveline (MGU-K) in addition to the internal combustion engine (ICE). The energy supply from the ES is mostly needed during sharp accelerations to avoid turbo-lag, and to boost torque at low speeds. At low speeds, it also improves the ratio of engine crankshaft power to fuel flow power, as well as the ratio of engine crankshaft plus turbocharger shaft power to fuel flow power. The energy supply to the ES is possible at high speeds and loads, where otherwise the turbine could have been waste gated, and during decelerations. This improves the ratio of engine crankshaft plus turbocharger shaft power to fuel flow power.

10th Annual Systems Engineering Conference - Focusing on Improving Performance of Defense Systems Programs. Volume 1. Tuesday Presentations

DTIC Science & Technology

2007-10-25

Exchange Platforms Publishers Resellers iTunes Non-Profit/ Government/ Self- Managed Library of Congress Library Consortia Fed. Tech Transfer Sites Univ...Thompson Dialog – Thomson MicroPatent – Thomson Pharma – WIPO Digital Patent Library* (*nonprofit organization) • iTunes • IP Exchange Platforms...Elsevier SciDirect – Nat’l Acad. Press – Lexis, Westlaw – Newspaper web sites • iTunes • Resellers of Copyrighted Material – JSTOR – EBSCOHost

Improving Legacy Aircraft Systems Through Condition-Based Maintenance: An H-60 Case Study

DTIC Science & Technology

2014-09-01

level functions. These decompositions are equivalent to a detailed design effort in systems engineering. NAMPSOPs have a common architectural structure...Assembly Power Available Spindle Cables No.1 Engine Load Demand Spindle Control Cables Engine Pneumatic Starters Auxiliary Power Unit IRCM FLIR Mission...Analysis Fuel System Main Rotor Head Main Module Main Gear Box Radiator Engine Output Shaft Auxiliary Power Unit Flight Control Cables Tail Landing

A novel double gate MOSFET by symmetrical insulator packets with improved short channel effects

NASA Astrophysics Data System (ADS)

Ramezani, Zeinab; Orouji, Ali A.

2018-03-01

In this article, we study a novel double-gate SOI MOSFET structure incorporating insulator packets (IPs) at the junction between channel and source/drain (S/D) ends. The proposed MOSFET has great strength in inhibiting short channel effects and OFF-state current that are the main problems compared with conventional one due to the significant suppressed penetrations of both the lateral electric field and the carrier diffusion from the S/D into the channel. Improvement of the hot electron reliability, the ON to OFF drain current ratio, drain-induced barrier lowering, gate-induced drain leakage and threshold voltage over conventional double-gate SOI MOSFETs, i.e. without IPs, is displayed with the simulation results. This study is believed to improve the CMOS device reliability and is suitable for the low-power very-large-scale integration circuits.

Integrated thermal and energy management of plug-in hybrid electric vehicles

NASA Astrophysics Data System (ADS)

Shams-Zahraei, Mojtaba; Kouzani, Abbas Z.; Kutter, Steffen; Bäker, Bernard

2012-10-01

In plug-in hybrid electric vehicles (PHEVs), the engine temperature declines due to reduced engine load and extended engine off period. It is proven that the engine efficiency and emissions depend on the engine temperature. Also, temperature influences the vehicle air-conditioner and the cabin heater loads. Particularly, while the engine is cold, the power demand of the cabin heater needs to be provided by the batteries instead of the waste heat of engine coolant. The existing energy management strategies (EMS) of PHEVs focus on the improvement of fuel efficiency based on hot engine characteristics neglecting the effect of temperature on the engine performance and the vehicle power demand. This paper presents a new EMS incorporating an engine thermal management method which derives the global optimal battery charge depletion trajectories. A dynamic programming-based algorithm is developed to enforce the charge depletion boundaries, while optimizing a fuel consumption cost function by controlling the engine power. The optimal control problem formulates the cost function based on two state variables: battery charge and engine internal temperature. Simulation results demonstrate that temperature and the cabin heater/air-conditioner power demand can significantly influence the optimal solution for the EMS, and accordingly fuel efficiency and emissions of PHEVs.

Integration of Wind Energy Systems into Power Engineering Education Program at UW-Madison

DOE Office of Scientific and Technical Information (OSTI.GOV)

Venkataramanan, Giri; Lesieutre, Bernard; Jahns, Thomas

This project has developed an integrated curriculum focused on the power engineering aspects of wind energy systems that builds upon a well-established graduate educational program at UW- Madison. Five new courses have been developed and delivered to students. Some of the courses have been offered on multiple occasions. The courses include: Control of electric drives for Wind Power applications, Utility Applications of Power Electronics (Wind Power), Practicum in Small Wind Turbines, Utility Integration of Wind Power, and Wind and Weather for Scientists and Engineers. Utility Applications of Power Electronics (Wind Power) has been provided for distance education as well asmore » on-campus education. Several industrial internships for students have been organized. Numerous campus seminars that provide discussion on emerging issues related to wind power development have been delivered in conjunction with other campus events. Annual student conferences have been initiated, that extend beyond wind power to include sustainable energy topics to draw a large group of stakeholders. Energy policy electives for engineering students have been identified for students to participate through a certificate program. Wind turbines build by students have been installed at a UW-Madison facility, as a test-bed. A Master of Engineering program in Sustainable Systems Engineering has been initiated that incorporates specializations that include in wind energy curricula. The project has enabled UW-Madison to establish leadership at graduate level higher education in the field of wind power integration with the electric grid.« less

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2011 CFR

2011-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2010 CFR

2010-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2012 CFR

2012-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2014 CFR

2014-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Code of Federal Regulations, 2013 CFR

2013-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...) Ground locking: A total of 45 hours with the propeller brake engaged in a manner which clearly...

Continued Investigation of Leakage and Power Loss Test Results for Competing Turbine Engine Seals

NASA Technical Reports Server (NTRS)

Delgado, Irebert R.; Proctor, Margaret P.

2006-01-01

Secondary seal leakage in jet engine applications results in power losses to the engine cycle. Likewise, seal power loss in jet engines not only result in efficiency loss but also increase the heat input into the engine resulting in reduced component lives. Experimental work on labyrinth and annular seals was performed at NASA Glenn Research Center to quantify seal leakage and power loss at various temperatures, seal pressure differentials, and surface speeds. Data from annular and labyrinth seals are compared with previous brush and finger seal test results. Data are also compared to literature. Annular and labyrinth seal leakage rates are 2 to 3 times greater than brush and finger seal rates. Seal leakage decreases with increasing speed but increases with increasing test temperature due to thermal expansion mismatch. Also seal power loss increases with surface speed, seal pressure differential, mass flow rate, and radial clearance. Annular and labyrinth seal power losses were higher than those of brush or finger seal data. The brush seal power loss was 15 to 30 percent lower than annular and labyrinth seal power loss.

Subtype-selective regulation of IP3 receptors by thimerosal via cysteine residues within the IP3-binding core and suppressor domain

PubMed Central

Khan, Samir A.; Rossi, Ana M.; Riley, Andrew M.; Potter, Barry V. L.; Taylor, Colin W.

2013-01-01

IP3R (IP3 [inositol 1,4,5-trisphosphate] receptors) and ryanodine receptors are the most widely expressed intracellular Ca2+ channels and both are regulated by thiol reagents. In DT40 cells stably expressing single subtypes of mammalian IP3R, low concentrations of thimerosal (also known as thiomersal), which oxidizes thiols to form a thiomercurylethyl complex, increased the sensitivity of IP3-evoked Ca2+ release via IP3R1 and IP3R2, but inhibited IP3R3. Activation of IP3R is initiated by IP3 binding to the IBC (IP3-binding core; residues 224–604) and proceeds via re-arrangement of an interface between the IBC and SD (suppressor domain; residues 1–223). Thimerosal (100 μM) stimulated IP3 binding to the isolated NT (N-terminal; residues 1–604) of IP3R1 and IP3R2, but not to that of IP3R3. Binding of a competitive antagonist (heparin) or partial agonist (dimeric-IP3) to NT1 was unaffected by thiomersal, suggesting that the effect of thimerosal is specifically related to IP3R activation. IP3 binding to NT1 in which all cysteine residues were replaced by alanine was insensitive to thimerosal, so too were NT1 in which cysteine residues were replaced in either the SD or IBC. This demonstrates that thimerosal interacts directly with cysteine in both the SD and IBC. Chimaeric proteins in which the SD of the IP3R was replaced by the structurally related A domain of a ryanodine receptor were functional, but thimerosal inhibited both IP3 binding to the chimaeric NT and IP3-evoked Ca2+ release from the chimaeric IP3R. This is the first systematic analysis of the effects of a thiol reagent on each IP3R subtype. We conclude that thimerosal selectively sensitizes IP3R1 and IP3R2 to IP3 by modifying cysteine residues within both the SD and IBC and thereby stabilizing an active conformation of the receptor. PMID:23282150

Preliminary investigation of the control of a gas-turbine engine for a helicopter / Richard P. Krebs

NASA Technical Reports Server (NTRS)

Krebs, Richard P

1951-01-01

An analog investigation of the power plant for a gas-turbine powered helicopter indicates that currently proposed turbine-propeller engine controls are satisfactory for helicopter application. Power increases from one-half to full rated at altitudes from sea level to 15,000 feet could be made in less than 4 seconds with either the rotor or propellers absorbing the engine power.

Training Civil Engineering Enlisted Personnel Past, Present and Future

DTIC Science & Technology

1989-09-01

engines, 90; diesel fuel injector systems, 60; exciters and alternators, 60; power plant installation, 60; power plant maintenance, 30; power centers, 30...ENGINEERING COURSES AND STUDENTS GRADUATED, MAY-JUNE 1946. Course Titles Weeks’ No. of Length Grads. Diesel Mechanic 8 58 Auto Equipment Mechanic 8 116...134 Power Shovel 105 Crawler Tractor 315 Miscellaneous and Well Driller 87 *Construction Technician 235 Crane Operator 66 * Diesel Mechanic 252

14 CFR 91.1037 - Large transport category airplanes: Turbine engine powered; Limitations; Destination and...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 2 2012-01-01 2012-01-01 false Large transport category airplanes: Turbine....1037 Large transport category airplanes: Turbine engine powered; Limitations; Destination and alternate airports. (a) No program manager or any other person may permit a turbine engine powered large transport...

14 CFR 91.1037 - Large transport category airplanes: Turbine engine powered; Limitations; Destination and...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 2 2014-01-01 2014-01-01 false Large transport category airplanes: Turbine....1037 Large transport category airplanes: Turbine engine powered; Limitations; Destination and alternate airports. (a) No program manager or any other person may permit a turbine engine powered large transport...

14 CFR 91.1037 - Large transport category airplanes: Turbine engine powered; Limitations; Destination and...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 2 2013-01-01 2013-01-01 false Large transport category airplanes: Turbine....1037 Large transport category airplanes: Turbine engine powered; Limitations; Destination and alternate airports. (a) No program manager or any other person may permit a turbine engine powered large transport...

40 CFR 60.4202 - What emission standards must I meet for emergency engines if I am a stationary CI internal...

Code of Federal Regulations, 2014 CFR

2014-07-01

... CI ICE with a maximum engine power less than or equal to 2,237 KW (3,000 HP) and a displacement of... CI ICE with a maximum engine power greater than 2,237 KW (3,000 HP) and a displacement of less than... CFR 94.8, as applicable, for all pollutants, for the same displacement and maximum engine power: (1...

40 CFR 60.4202 - What emission standards must I meet for emergency engines if I am a stationary CI internal...

Code of Federal Regulations, 2012 CFR

2012-07-01

... CI ICE with a maximum engine power less than or equal to 2,237 KW (3,000 HP) and a displacement of... CI ICE with a maximum engine power greater than 2,237 KW (3,000 HP) and a displacement of less than... CFR 94.8, as applicable, for all pollutants, for the same displacement and maximum engine power: (1...

40 CFR 60.4202 - What emission standards must I meet for emergency engines if I am a stationary CI internal...

Code of Federal Regulations, 2013 CFR

2013-07-01

... CI ICE with a maximum engine power less than or equal to 2,237 KW (3,000 HP) and a displacement of... CI ICE with a maximum engine power greater than 2,237 KW (3,000 HP) and a displacement of less than... CFR 94.8, as applicable, for all pollutants, for the same displacement and maximum engine power: (1...

The Technology of Suppressing Harmonics with Complex Neural Network is Applied to Microgrid

NASA Astrophysics Data System (ADS)

Zhang, Jing; Li, Zhan-Ying; Wang, Yan-ping; Li, Yang; Zong, Ke-yong

2018-03-01

According to the traits of harmonics in microgrid, a new CANN controller which combines BP and RBF neural network is proposed to control APF to detect and suppress harmonics. This controller has the function of current prediction. By simulation in Matlab / Simulink, this design can shorten the delay time nearly 0.02s (a power supply current cycle) in comparison with the traditional controller based on ip-iq method. The new controller also has higher compensation accuracy and better dynamic tracking traits, it can greatly suppress the harmonics and improve the power quality.