DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Junming; Baylon, Rebecca A.; Liu, Changjun

The effects of surface acidity on the cascade ethanol-to-isobutene conversion were studied using ZnxZryOz catalysts. The ethanol-to-isobutene reaction was found to be limited by the secondary reaction of the key intermediate, acetone, namely the acetone-to-isobutene reaction. Although the catalysts with coexisting Brønsted acidity could catalyze the rate-limiting acetone-to-isobutene reaction, the presence of Brønsted acidity is also detrimental. First, secondary isobutene isomerization is favored, producing a mixture of butene isomers. Second, undesired polymerization and coke formation prevail, leading to rapid catalyst deactivation. Most importantly, both steady-state and kinetic reaction studies as well as FTIR analysis of adsorbed acetone-d6 and D2O unambiguouslymore » showed that a highly active and selective nature of balanced Lewis acid-base pairs was masked by the coexisting Brønsted acidity in the aldolization and self-deoxygenation of acetone to isobutene. As a result, ZnxZryOz catalysts with only Lewis acid-base pairs were discovered, on which nearly a theoretical selectivity to isobutene (~88.9%) was successfully achieved, which has never been reported before. Moreover, the absence of Brønsted acidity in such ZnxZryOz catalysts also eliminates the side isobutene isomerization and undesired polymerization/coke reactions, resulting in the production of high purity isobutene with significantly improved catalyst stability (< 2% activity loss after 200 h time-on-stream). This work not only demonstrates a balanced Lewis acid-base pair for the highly active and selective cascade ethanol-to-isobutene reaction, but also sheds light on the rational design of selective and robust acid-base catalyst for C-C coupling via aldolization reaction.« less

EXTENDED ALKYLATE PRODUCTION ACTIVITY DURING FIXED-BED SUPERCRITICAL 1-BUTENE/ISOBUTANE ALKYLATION ON SOLID ACID CATALYSTS USING CARBON DIOXIDE AS DILUENT. (R824729)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

Catalytic dehydrogenation of isobutane in the presence of hydrogen over Cs-modified Ni2P supported on active carbon

NASA Astrophysics Data System (ADS)

Xu, Yanli; Sang, Huanxin; Wang, Kang; Wang, Xitao

2014-10-01

In this article, an environmentally friendly non-noble-metal class of Cs-Ni2P/active carbon (AC) catalyst was prepared and demonstrated to exhibit enhanced catalytic performance in isobutane dehydrogenation. The results of activity tests reveal that Ni/AC catalyst was highly active for isobutane cracking, which led to the formation of abundant methane and coke. After the introduction of phosphorus through impregnation with ammonium di-hydrogen phosphate and H2-temperature programmed reduction, undesired cracking reactions were effectively inhibited, and the selectivity to isobutene and stability of catalyst increased remarkably. The characterization results indicate that, after the addition of phosphorous, the improvement of dehydrogenation selectivity is ascribed to the partial positive charges carried on Ni surface in Ni2P particles, which decreases the strength of Nisbnd C bond between Ni and carbonium-ion intermediates and the possibility of excessive dehydrogenation. In addition, Cs-modified Ni2P/AC catalysts display much higher catalytic performance as compared to Ni2P/AC catalyst. Cs-Ni2P-6.5 catalyst has the highest catalytic performance, and the selectivity to isobutene higher than 93% can be obtained even after 4 h reaction. The enhancement in catalytic performance of the Cs-modified catalysts is mainly attributed to the function of Cs to improve the dispersion of Ni2P particles, transfer electron from Cs to Ni, and decrease acid site number and strength.

KINETIC ANALYSIS OF THE ALKYLATION REACTION OF ISOBUTANE WITH 1-BUTENE ON A SOLID ACID CATALYST IN GAS, LIQUID, AND SUPERCRITICAL REACTION MEDIA. (R826694C669)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

Oxidative dehydrogenation of isobutane over vanadia catalysts supported by titania nanoshapes

DOE PAGES

Kraemer, Shannon K.; Rondinone, Adam Justin; Tsai, Yu-Tung; ...

2015-11-02

Support plays a complex role in catalysis by supported metal oxides and the exact support effect still remains elusive. One of the approaches to gain fundamental insights into the support effect is to utilize model support systems. In this study, we employed for the first time titania nanoshapes as the model supports and investigated how the variation of surface structure of the support (titania, TiO 2) impacts the catalysis of supported oxide (vanadia, VO x). TiO 2 truncated rhombi, spheres and rods were synthesized via hydrothermal method and characterized with XRD and TEM. These TiO 2 nanoshapes represent different mixturesmore » of surface facets including [1 0 1], [0 1 0] and [0 0 1] and were used to support vanadia. The structure of supported VO x species was characterized in detail with in situ Raman spectroscopy as a function of loading on the three TiO 2 nanoshapes. Oxidative dehydrogenation (ODH) of isobutane to isobutene was used as a model reaction to test how the support shape influences the activity, selectivity and activation energy of the surface VO x species. It was shown that the shape of TiO 2 support does not pose evident effect on either the structure of surface VO x species or the catalytic performance of surface VO x species in isobutane ODH reaction. Finally, this insignificant support shape effect was ascribed to the small difference in the surface oxygen vacancy formation energy among the different TiO 2 surfaces and the multi-faceting nature of the TiO 2 nanoshapes.« less

Oxidative dehydrogenation of isobutane over vanadia catalysts supported by titania nanoshapes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kraemer, Shannon; Rondinone, Adam J.; Tsai, Yu-Tong

2016-04-01

Support plays a complex role in catalysis by supported metal oxides and the exact support effect still remains elusive. One of the approaches to gain fundamental insights into the support effect is to utilize model support systems. In this paper, we employed for the first time titania nanoshapes as the model supports and investigated how the variation of surface structure of the support (titania, TiO2) impacts the catalysis of supported oxide (vanadia, VOx). TiO2 truncated rhombi, spheres and rods were synthesized via hydrothermal method and characterized with XRD and TEM. These TiO2 nanoshapes represent different mixtures of surface facets includingmore » [1 0 1], [0 1 0] and [0 0 1] and were used to support vanadia. The structure of supported VOx species was characterized in detail with in situ Raman spectroscopy as a function of loading on the three TiO2 nanoshapes. Oxidative dehydrogenation (ODH) of isobutane to isobutene was used as a model reaction to test how the support shape influences the activity, selectivity and activation energy of the surface VOx species. It was shown that the shape of TiO2 support does not pose evident effect on either the structure of surface VOx species or the catalytic performance of surface VOx species in isobutane ODH reaction. This insignificant support shape effect was ascribed to the small difference in the surface oxygen vacancy formation energy among the different TiO2 surfaces and the multi-faceting nature of the TiO2 nanoshapes.« less

Formation of isobutene from 3-hydroxy-3-methylbutyrate by diphosphomevalonate decarboxylase.

PubMed

Gogerty, David S; Bobik, Thomas A

2010-12-01

Isobutene is an important commercial chemical used for the synthesis of butyl rubber, terephthalic acid, specialty chemicals, and a gasoline performance additive known as alkylate. Currently, isobutene is produced from petroleum and hence is nonrenewable. Here, we report that the Saccharomyces cerevisiae mevalonate diphosphate decarboxylase (ScMDD) can convert 3-hydroxy-3-methylbutyrate (3-HMB) to isobutene. Whole cells of Escherichia coli producing ScMDD with an N-terminal 6×His tag (His(6)-ScMDD) formed isobutene from 3-HMB at a rate of 154 pmol h(-1) g cells(-1). In contrast, no isobutene was detected from control cells lacking ScMDD. His(6)-ScMDD was purified by nickel affinity chromatography and shown to produce isobutene from 3-HMB at a rate of 1.33 pmol min(-1) mg(-1) protein. Controls showed that both His(6)-ScMDD and 3-HMB were required for detectable isobutene formation. Isobutene was identified by gas chromatography (GC) with flame ionization detection as well as by GC-mass spectrometry (MS). ScMDD was subjected to error-prone PCR, and two improved variants were characterized, ScMDD1 (I145F) and ScMDD2 (R74H). Whole cells of E. coli producing ScMDD1 and ScMDD2 produced isobutene from 3-HMB at rates of 3,000 and 5,888 pmol h(-1) g cells(-1), which are 19- and 38-fold increases compared to rates for cells producing His(6)-ScMDD. This showed that genetic modifications can be used to increase the rate at which ScMDD converts 3-HMB to isobutene. Because 3-HMB can be produced from l-leucine, ScMDD has a potential application for the production of renewable isobutene. Moreover, isobutene is a gas, which might simplify its purification from a fermentation medium, substantially reducing production costs.

Capillary Columns with a Sorbent Based on Functionalized Poly(1-Trimethylsilyl-1-Propyne) for the Elution Analysis of Natural Gas

NASA Astrophysics Data System (ADS)

Yakovleva, E. Yu.; Patrushev, Yu. V.; Pai, Z. P.

2018-05-01

The chromatographic properties of capillary columns prepared using functionalized poly(1- trimethylsilyl-1-propyne) (PTMSP) are evaluated and compared with the performance of a commercial column with divinylbenzene polymer sorbent. The loading capacity of a PTMSP column with dimensions of 30 m × 0.53 mm × 0.8 μm is shown to be about 2.5 times higher than that of a divinylbenzene polymer column with a diameter of 0.32 mm and a film thickness of 10 μm. The increased value of the background current for PTMSP columns at 220°C is explained by the presence of non-polar bulky substituents in the polymer chain. Differences in the order of elution are found for the following pairs of compounds: acetylene-ethylene; ethane-water; butene-1-isobutane; and sulfur dioxide-carbonyl sulfide. On a column with the functionalized PTMC, analysis of a mixture composition close to natural gas is found to be complete within 27 min.

Laboratory spectroscopic analyses of electron irradiated alkanes and alkenes in solar system ices

NASA Astrophysics Data System (ADS)

Hand, K. P.; Carlson, R. W.

2012-03-01

We report results from laboratory experiments of 10 keV electron irradiation of thin ice films of water and short-chain hydrocarbons at ˜10-8 Torr and temperatures ranging from 70-100 K. Hydrocarbon mixtures include water with C3H8, C3H6, C4H10 (butane and isobutane), and C4H8, (1-butene and cis/trans-2-butene). The double bonds of the alkenes in our initial mixtures were rapidly destroyed or converted to single carbon bonds, covalent bonds with hydrogen, bonds with -OH (hydroxyl), bonds with oxygen (C-O), or double bonds with oxygen (carbonyl). Spectra resulting from irradiation of alkane and alkene ices are largely indistinguishable; the initial differences in film composition are destroyed and the resulting mixture includes long-chain, branched aliphatics, aldehydes, ketones, esters, and alcohols. Methane was observed as a product during radiolysis but CO was largely absent. We find that while some of the carbon is oxidized and lost to CO2 formation, some carbon is sequestered into highly refractory, long-chain aliphatic compounds that remain as a thin residue even after the ice film has been raised to standard temperature and pressure. We conclude that the high availability of hydrogen in our experiments leads to the formation of the formyl radical which then serves as the precursor for formaldehyde and polymerization of longer hydrocarbon chains.

Fermentative production of isobutene.

PubMed

van Leeuwen, Bianca N M; van der Wulp, Albertus M; Duijnstee, Isabelle; van Maris, Antonius J A; Straathof, Adrie J J

2012-02-01

Isobutene (2-methylpropene) is one of those chemicals for which bio-based production might replace the petrochemical production in the future. Currently, more than 10 million metric tons of isobutene are produced on a yearly basis. Even though bio-based production might also be achieved through chemocatalytic or thermochemical methods, this review focuses on fermentative routes from sugars. Although biological isobutene formation is known since the 1970s, extensive metabolic engineering is required to achieve economically viable yields and productivities. Two recent metabolic engineering developments may enable anaerobic production close to the theoretical stoichiometry of 1isobutene + 2CO(2) + 2H(2)O per mol of glucose. One relies on the conversion of 3-hydroxyisovalerate to isobutene as a side activity of mevalonate diphosphate decarboxylase and the other on isobutanol dehydration as a side activity of engineered oleate hydratase. The latter resembles the fermentative production of isobutanol followed by isobutanol recovery and chemocatalytic dehydration. The advantage of a completely biological route is that not isobutanol, but instead gaseous isobutene is recovered from the fermenter together with CO(2). The low aqueous solubility of isobutene might also minimize product toxicity to the microorganisms. Although developments are at their infancy, the potential of a large scale fermentative isobutene production process is assessed. The production costs estimate is 0.9 Euro kg(-1), which is reasonably competitive. About 70% of the production costs will be due to the costs of lignocellulose hydrolysate, which seems to be a preferred feedstock.

21 CFR 177.1570 - Poly-1-butene resins and butene/ethylene copolymers.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Poly-1-butene resins and butene/ethylene copolymers... resins and butene/ethylene copolymers. The poly-1-butene resins and butene/ethylene copolymers identified... the catalytic polymerization of 1-butene liquid monomer. Butene/ethylene copolymers are produced by...

Stability of bound species during alkene reactions on solid acids

NASA Astrophysics Data System (ADS)

Sarazen, Michele L.; Iglesia, Enrique

2017-05-01

This study reports the thermodynamics of bound species derived from ethene, propene, n-butene, and isobutene on solid acids with diverse strength and confining voids. Density functional theory (DFT) and kinetic data indicate that covalently bound alkoxides form C-C bonds in the kinetically relevant step for dimerization turnovers on protons within TON (0.57 nm) and MOR (0.67 nm) zeolitic channels and on stronger acids HPW (polyoxometalate clusters on silica). Turnover rates for mixed alkenes give relative alkoxide stabilities; the respective adsorption constants are obtained from in situ infrared spectra. Tertiary alkoxides (from isobutene) within larger voids (MOR, HPW) are more stable than less substituted isomers but are destabilized within smaller concave environments (TON) because framework distortions are required to avoid steric repulsion. Adsorption constants are similar on MOR and HPW for each alkoxide, indicating that binding is insensitive to acid strength for covalently bound species. DFT-derived formation free energies for alkoxides with different framework attachments and backbone length/structure agree with measurements when dispersion forces, which mediate stabilization by confinement in host-guest systems, are considered. Theory reveals previously unrecognized framework distortions that balance the C-O bond lengths required for covalency with host-guest distances that maximize van der Waals contacts. These distortions, reported here as changes in O-atom locations and dihedral angles, become stronger for larger, more substituted alkoxides. The thermodynamic properties reported here for alkoxides and acid hosts differing in size and conjugate-anion stability are benchmarked against DFT-derived free energies; their details are essential to design host-guest pairs that direct alkoxide species toward specific products.

21 CFR 177.1570 - Poly-1-butene resins and butene/ethylene copolymers.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Poly-1-butene resins and butene/ethylene... Substances for Use as Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1570 Poly-1-butene resins and butene/ethylene copolymers. The poly-1-butene resins and butene/ethylene copolymers...

The Putative Mevalonate Diphosphate Decarboxylase from Picrophilus torridus Is in Reality a Mevalonate-3-Kinase with High Potential for Bioproduction of Isobutene

PubMed Central

Hall, Stephen J.; Eastham, Graham; Licence, Peter; Stephens, Gill

2015-01-01

Mevalonate diphosphate decarboxylase (MVD) is an ATP-dependent enzyme that catalyzes the phosphorylation/decarboxylation of (R)-mevalonate-5-diphosphate to isopentenyl pyrophosphate in the mevalonate (MVA) pathway. MVD is a key enzyme in engineered metabolic pathways for bioproduction of isobutene, since it catalyzes the conversion of 3-hydroxyisovalerate (3-HIV) to isobutene, an important platform chemical. The putative homologue from Picrophilus torridus has been identified as a highly efficient variant in a number of patents, but its detailed characterization has not been reported. In this study, we have successfully purified and characterized the putative MVD from P. torridus. We discovered that it is not a decarboxylase per se but an ATP-dependent enzyme, mevalonate-3-kinase (M3K), which catalyzes the phosphorylation of MVA to mevalonate-3-phosphate. The enzyme's potential in isobutene formation is due to the conversion of 3-HIV to an unstable 3-phosphate intermediate that undergoes consequent spontaneous decarboxylation to form isobutene. Isobutene production rates were as high as 507 pmol min−1 g cells−1 using Escherichia coli cells expressing the enzyme and 2,880 pmol min−1 mg protein−1 with the purified histidine-tagged enzyme, significantly higher than reported previously. M3K is a key enzyme of the novel MVA pathway discovered very recently in Thermoplasma acidophilum. We suggest that P. torridus metabolizes MVA by the same pathway. PMID:25636853

Phase equilibria of CFC alternative refrigerant mixtures: Binary systems of isobutane + 1,1,1,2-tetrafluoroethane, + 1,1-difluoroethane, and + difluoromethane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lim, J.S.; Park, J.Y.; Lee, B.G.

1999-12-01

Isothermal vapor-liquid equilibria were measured in the binary systems 1,1,1,2-tetrafluoroethane + isobutane at 303.2 and 323.2 K, 1,1-difluoroethane + isobutane at 303.2, 313.2, 323.2, and 333.2 K, and difluoromethane + isobutane at 301.8 and 321.8 K in a circulation-type equilibrium apparatus. The experimental data were well correlated with the Peng-Robinson equation of state using the Wong and Sandler mixing rules.

THE RADIATION-INDUCED POLYMERIZATION OF ISOBUTENE: A LIQUID PHASE IONIC REACTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collinson, E.; Dainton, F.S.; Gillis, H.A.

1959-06-01

New evidence is presented in support of the suggestion that the gamma - ray-induced polymerization of liquid isobutene at -78 deg C proceeds solely by a cationic mechanism. Attempts to polymerize isobutene at -78 deg C with free radicals from the photolysis of diacetyl, benzoin and benzil were unsuccessful but the benzil solution irradiated with ultraviolet light at 77 deg K was shown by electron spin resonance measurements to give rise to radicals from the isobutene. Isobutene irradiated in the pure state at a gamma -ray dose rate of 7 x 10/sup 17/ e.v. ml/sup -1/ min/sup -1/ polymerized withmore » G(-C/sub 4/H/sub 8/) = 3.0 plus or minus 1.7 x 10/sup 2/. Solutions of FeCl/sub 3/, DPPH, benzoquinone and iodine in isobutene were also irradiated with gamma -rays. Of these solutes, only benzoquinone reduced the polymerization rate to zero, and DPPH had no significant effect. The effects of FeCl/sub 3/ and I/2 on the polymerization were complicated by other factors. The measured yields of conversion of the solutes after irradiation were G(-DPPH) =3.7 plus or minus 0.2, G(Fe(II)) = 3.0 plus or minus 0.5 and G(-Q) = 1.5 plus or minus 0.2. The electron spin resonance spectrum of isobutene irradiated with gamma -rays at 77 deg K showed the presence of H atoms which disappeared rapidly, and a more stable radical, the spectrum of which consisted of 6 peaks having an over-all spacing of 158 gauss at the operating frequency of 9400 Mc sec./sup -1/. The same six peak pattern was obtained from cyclopropane irradiated with gamma rays at 77 deg K and from a solution of benzil in isoDutene irradiated with ultraviolet light at 77 deg K. It is concluded that the radical responsible for this spectrum is either the cyclopropyl radical or the methyl substituted allyl radical, the latter being the less likely. The most likely initiating ion is considered to be (CH/sub 3/)/sub 3/C/sup +/, and a mechanism consistent with the available data is proposed. (auth)« less

21 CFR 177.1570 - Poly-1-butene resins and butene/ethylene copolymers.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) Viscosity. Poly-1-butene resins and the butene/ethylene copolymers have an intrinsic viscosity 1.0 to 3.2 as determined by ASTM method D1601-78, “Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers...

Enhanced diisobutene production in the presence of methyl tertiary butyl ether

DOEpatents

Smith, L.A. Jr.

1983-03-01

In the liquid phase reaction of isobutene in the presence of resin cation exchange resins with itself in a C[sub 4] hydrocarbon stream to form dimers, the formation of higher polymers, oligomers, and co-dimer by-products is suppressed by the presence of 0.0001 to 1 mole per mole of isobutene of methyl tertiary butyl ether. 1 fig.

21 CFR 177.1570 - Poly-1-butene resins and butene/ethylene copolymers.

Code of Federal Regulations, 2013 CFR

2013-04-01

... their characteristic infrared spectra. (ii) Viscosity. Poly-1-butene resins and the butene/ethylene copolymers have an intrinsic viscosity 1.0 to 3.2 as determined by ASTM method D1601-78, “Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers,” which is incorporated by reference. Copies...

21 CFR 177.1570 - Poly-1-butene resins and butene/ethylene copolymers.

Code of Federal Regulations, 2012 CFR

2012-04-01

... their characteristic infrared spectra. (ii) Viscosity. Poly-1-butene resins and the butene/ethylene copolymers have an intrinsic viscosity 1.0 to 3.2 as determined by ASTM method D1601-78, “Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers,” which is incorporated by reference. Copies...

Use of propane as a quench gas in argon-filled proportional counters and comparison with other quench gases

NASA Technical Reports Server (NTRS)

Agrawal, P. C.; Ramsey, B. D.

1988-01-01

An experimental investigation of propane and six other quench gases was carried out in argon-filled proportional counters. The objective of the study was to find the best gas mixture for optimizing the gas gain and the energy resolution as well as to understand the role of the ionization potential of quench gases in determining these parameters. It was found that the best gas gains and energy resolutions are obtained with propane, ethane, and isobutane in that order. The ionization potentials of these three lie below the argon metastable potentials and have the lowest value of resonance defect compared to the other quench gases. The better results obtained with these mixtures can be explained by an increased ionization yield resulting from the Penning effect. Propylene and trans-2-butene give inferior performance compared to the above three gases. Methane and carbon dioxide, the most commonly used quench gases in the argon-filled detectors, provide the worst results.

Laboratory Analysis Of Water, Hydrocarbon And Ammonia Ice Mixtures Exposed To High-energy Electron Irradiation

NASA Astrophysics Data System (ADS)

Hand, Kevin P.; Carlson, R. W.; Tsapin, A. I.

2006-09-01

Irradiation of low temperature ices in the laboratory provides insight into processes that may be occurring on icy bodies in the solar system. Here we report on results from high-energy (10keV) electron irradiation of thin ice films at 1e-8 torr and 70-120K. Mixtures include water with CO2, C3H8, C3H6, C4H10 (butane and isobutane), C4H8,(1-butene and cis/trans-2-butene), and NH3. During irradiation of H2O + alkane films at 80K, CO2 and CH4 production is observed and both species are retained in the ice, possibly trapped in clathrates. The -CH3 infrared bands initially present are seen to decrease with increasing dose. Bands associated with -CH2- persist, indicating polymerization of the initial short-chain hydrocarbons. In alkenes a similar evolution toward polymerization is observed, however the first step appears to be the destruction of the C=C bond. Upon warming of the film, mass spectra data compliment the mid-infrared data and indicate the production of H2CO, however glycolic acid is not explicitly seen in the mass spectra. When warmed to 300K, residues remained for all irradiated films except that of the H2O + CO2 mixtures. Residues were analyzed with Matrix Assisted Laser Desorption/Ionization Mass Spectrometry (MALDI). Results show the production of large aliphatic, very refractory, hydrocarbons (with m/z up to 2500). Mid-infrared spectra of the residues indicate carbonyls and alcohols, likely due to polymerized aldehydes and carboxylic acids. Films of H2O + C3H8 + NH3 at 70K show the production of OCN- (cyanate ion), formamide, along with other possible amides and hydrocarbons. HPLC results indicate the production of racemic alanine. Finally, results of abiotic experiments are compared to results from the irradiation of bacterial spores in ice. The application to Europa and Enceladus is discussed.

Theoretical Kinetics Analysis for Ḣ Atom Addition to 1,3-Butadiene and Related Reactions on the Ċ4H7 Potential Energy Surface.

PubMed

Li, Yang; Klippenstein, Stephen J; Zhou, Chong-Wen; Curran, Henry J

2017-10-12

The oxidation chemistry of the simplest conjugated hydrocarbon, 1,3-butadiene, can provide a first step in understanding the role of polyunsaturated hydrocarbons in combustion and, in particular, an understanding of their contribution toward soot formation. On the basis of our previous work on propene and the butene isomers (1-, 2-, and isobutene), it was found that the reaction kinetics of Ḣ-atom addition to the C═C double bond plays a significant role in fuel consumption kinetics and influences the predictions of high-temperature ignition delay times, product species concentrations, and flame speed measurements. In this study, the rate constants and thermodynamic properties for Ḣ-atom addition to 1,3-butadiene and related reactions on the Ċ 4 H 7 potential energy surface have been calculated using two different series of quantum chemical methods and two different kinetic codes. Excellent agreement is obtained between the two different kinetics codes. The calculated results including zero-point energies, single-point energies, rate constants, barrier heights, and thermochemistry are systematically compared among the two quantum chemical methods. 1-Methylallyl (Ċ 4 H 7 1-3) and 3-buten-1-yl (Ċ 4 H 7 1-4) radicals and C 2 H 4 + Ċ 2 H 3 are found to be the most important channels and reactivity-promoting products, respectively. We calculated that terminal addition is dominant (>80%) compared to internal Ḣ-atom addition at all temperatures in the range 298-2000 K. However, this dominance decreases with increasing temperature. The calculated rate constants for the bimolecular reaction C 4 H 6 + Ḣ → products and C 2 H 4 + Ċ 2 H 3 → products are in excellent agreement with both experimental and theoretical results from the literature. For selected C 4 species, the calculated thermochemical values are also in good agreement with literature data. In addition, the rate constants for H atom abstraction by Ḣ atoms have also been calculated, and it is found that abstraction from the central carbon atoms is the dominant channel (>70%) at temperatures in the range of 298-2000 K. Finally, by incorporating our calculated rate constants for both Ḣ atom addition and abstraction into our recently developed 1,3-butadiene model, we show that laminar flame speed predictions are significantly improved, emphasizing the value of this study.

The Bond Dissociation Energies of 1-Butene

NASA Technical Reports Server (NTRS)

Bauschlicher, Charles W., Jr.; Langhoff, Stephen R. (Technical Monitor)

1994-01-01

The bond dissociation energies of 1-butene and several calibration systems are computed using the G2(MP2) approach. The agreement between the calibration systems and experiment is very good. The computed values for 1-butene are compared with calibration systems and the agreement between the computed results for 1-butene and the "rule of thumb" values from the smaller systems is remarkably good.

Kinetic Studies of the Cometabolism of 1,4-DIOXANE and Chlorinated Aliphatic Hydrocarbon Mixtures by Rhodococcus Rhodochrous Grown on Isobutane

NASA Astrophysics Data System (ADS)

Rolston, H. M.; Semprini, L.; Thankitkul, S.; Azizian, M.; Hyman, M. R.

2016-12-01

1,4-dioxane (1,4-D) is a frequently observed groundwater contaminant due to its use as a stabilizer in commercial solvent formulations. In situ bioremediation could potentially provide a large cost savings for treatment of mixtures of chlorinated aliphatic hydrocarbons (CAHs) that include 1,4-D. Aerobic cometabolism is a particularly attractive option, as microorganisms can be stimulated in situ using specific primary substrates. Results will be presented that show the model isobutane-metabolizing bacteria, Rhodococcus rhodochrous (ATCC 21198), has the ability to transform 14-D at high rates and transformation capacities to concentrations below the drinking water screening level of 0.67 µg L-1. Resting cell transformation tests showed 1,4-D and a broad range of CAHs can be cometabolized by ATCC 21198. The maximum transformation rate (kmax) and the half-substrate coefficient (Ks) were determined for isobutane (the growth substrate), 1,4-D, 1,1,1-trichloroethane (1,1,1-TCA), 1,1,2-trichloroethane (1,1,2-TCA), 1,1-dichloroethane (1,1-DCA); 1,2-dichloroethane ((1,2-DCA) and 1,1-dichloroethene (1,1-DCE). Of the CAHs tested, 1,1-DCA had the highest kmax, approximately 25% of that for isobutane utilization, while 1,1,1-TCA had the lowest kmax, approximately 2% of isobutane's. 1,4-D was rapidly transformed and had a kmax 25% of that of isobutane. ATCC 21198 effectively transformed mixtures of 1,4-D, 1,1-DCE, 1,2-DCA and 1,1,1-TCA, both in the presence and absence isobutane. Model simulations were performed for the simultaneous cometabolism of 1,4-D and CAH mixtures by ATCC 21198, that included inhibition among the contaminants and isobutane , and terms for a limited transformation capacity. A good match to experimental observations was obtaining using the independently measured rate parameters. Results of model simulations will also be presented using a reactive transport model to evaluate conditions of in situ bioremediation using strain ATCC 21198.

40 CFR 60.707 - Chemicals affected by subpart RRR.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-7 Brometone 76-08-4 1,3-Butadiene 106-99-0 Butadiene and butene fractions n-Butane 106-97-8 1,4-Butanediol 110-63-4 Butanes, mixed 1-Butene 106-98-9 2-Butene 25167-67-3 Butenes, mixed n-Butyl acetate 123-86-4 Butyl acrylate 141-32-2 n-Butyl alcohol 71-36-3 sec-Butyl alcohol 78-92-2 tert-Butyl alcohol 75...

40 CFR 60.707 - Chemicals affected by subpart RRR.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-7 Brometone 76-08-4 1,3-Butadiene 106-99-0 Butadiene and butene fractions n-Butane 106-97-8 1,4-Butanediol 110-63-4 Butanes, mixed 1-Butene 106-98-9 2-Butene 25167-67-3 Butenes, mixed n-Butyl acetate 123-86-4 Butyl acrylate 141-32-2 n-Butyl alcohol 71-36-3 sec-Butyl alcohol 78-92-2 tert-Butyl alcohol 75...

40 CFR 60.707 - Chemicals affected by subpart RRR.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-7 Brometone 76-08-4 1,3-Butadiene 106-99-0 Butadiene and butene fractions n-Butane 106-97-8 1,4-Butanediol 110-63-4 Butanes, mixed 1-Butene 106-98-9 2-Butene 25167-67-3 Butenes, mixed n-Butyl acetate 123-86-4 Butyl acrylate 141-32-2 n-Butyl alcohol 71-36-3 sec-Butyl alcohol 78-92-2 tert-Butyl alcohol 75...

Enhanced diisobutene production in the presence of methyl tertiary butyl ether

DOEpatents

Smith, Jr., Lawrence A.

1983-01-01

In the liquid phase reaction of isobutene in the presence of resin cation exchange resins with itself in a C.sub.4 hydrocarbon stream to form dimers, the formation of higher polymers, oligomers, and co-dimer by-products is suppressed by the presence of 0.0001 to 1 mole per mole of isobutene of methyl tertiary butyl ether.

On studies of 3He and isobutane mixture as neutron proportional counter gas

NASA Astrophysics Data System (ADS)

Desai, S. S.; Shaikh, A. M.

2006-02-01

The performance of neutron detectors filled with 3He+iC 4H 10 (isobutane) gas mixtures has been studied and compared with the performance of detectors filled with 3He+Kr gas mixtures. The investigations are made to determine suitable concentration of isobutane in the gas mixture to design neutron proportional counters and linear position sensitive neutron detectors (1-D PSDs). Energy resolution, range of proportionality, plateau and gas gain characteristics are studied for various gas mixtures of 3He and isobutane. The values for various gas constants are determined by fitting the gas gains to Diethorn and Bateman's equations and their variation with isobutane concentration in the fill gas mixture is studied.

Host cells and methods for producing 3-methyl-2-buten-1-ol, 3-methyl-3-buten-1-ol, and 3-methyl-butan-1-ol

DOEpatents

Chou, Howard H [Berkeley, CA; Keasling, Jay D [Berkeley, CA

2011-07-26

The invention provides for a method for producing a 5-carbon alcohol in a genetically modified host cell. In one embodiment, the method comprises culturing a genetically modified host cell which expresses a first enzyme capable of catalyzing the dephosphorylation of an isopentenyl pyrophosphate (IPP) or dimethylallyl diphosphate (DMAPP), such as a Bacillus subtilis phosphatase (YhfR), under a suitable condition so that 5-carbon alcohol is 3-methyl-2-buten-1-ol and/or 3-methyl-3-buten-1-ol is produced. Optionally, the host cell may further comprise a second enzyme capable of reducing a 3-methyl-2-buten-1-ol to 3-methyl-butan-1-ol, such as a reductase.

Pyrolytic product characteristics of biosludge from the wastewater treatment plant of a petrochemical industry.

PubMed

Lin, Kuo-Hsiung; Hsu, Hui-Tsung; Ko, Ya-Wen; Shieh, Zhu-Xin; Chiang, Hung-Lung

2009-11-15

Biosludge was produced from the wastewater treatment plant of a petrochemical industry. The element compositions of pyrolytic residues, CO, CO(2), NOx, SOx, total hydrocarbons and detailed volatile organic compounds of pyrolytic gas, and C, H, N, S content and compositions in biofuel were determined in this study. Generally, 75-80% water content in sludge cakes and about 65-70% weight of water vapor and volatile compounds were volatilized during the drying process. Propene, propane, 1-butene, n-butane, isobutene, toluene and benzene were the major volatile organic compounds (VOCs) of the pyrolytic gas, and the concentrations for most of the top 20 VOC species were greater than 5 ppm. C(5)-C(9) compounds contributed 60% by weight of biofuel; 4-hydroxy-4-methyl-2-pentanone was the highest species, accounting for 28-53% of biofuel at various pyrolytic temperatures. Based on the dried residues, there was 8.5-13% weight in pyrolytic residues, 62-82% weight in liquid products (water and crude oil) and 5.8-30% weight in the gas phase after pyrolytic processing at 500-800 degrees C. Finally, 1.5-2.5 wt% liquid fuel was produced after the distillation process. The pyrolytic residues could be reused, the pyrolytic liquid product could be used as a fuel after distillation, and the pyrolytic gas could be recycled in the pyrolytic process to achieve non-toxic discharge and reduce the cost of sludge disposal.

Development of a Novel Leak-Free Constant-Pressure Cylinder for Certified Reference Materials of Liquid Hydrocarbon Mixtures.

PubMed

Kim, Yong Doo; Kang, Ji Hwan; Bae, Hyun Kil; Kang, Namgoo; Oh, Sang Hyub; Lee, Jin-Hong; Woo, Jin Chun; Lee, Sangil

2017-11-21

Liquid hydrocarbon mixtures such as liquefied petroleum gas and liquefied natural gas are becoming integral parts of the world's energy system. Certified reference materials (CRMs) of liquid hydrocarbon mixtures are necessary to allow assessment of the accuracy and traceability of the compositions of such materials. A piston-type constant-pressure cylinder (PCPC) comprising chambers for a pressurizing gas (helium) and liquid (hydrocarbons) separated by a piston can be used to develop accurate and traceable liquid hydrocarbon mixture CRMs. The development of accurate CRMs relies on the maintenance of their composition. However, a PCPC might allow hydrocarbons to leak owing to the imperfect seal of the piston. In this study, a novel leak-free bellows-type constant-pressure cylinder (BCPC) is designed and evaluated by comparison with PCPCs. Liquid hydrocarbon mixtures consisting of ethane, propane, propene, isobutane, n-butane, 1-butene, and isopentane were prepared in both types of constant pressure cylinders and then monitored to check leakages between the gas and liquid chambers. Overall, notable leakage occurred from and into both chambers in the PCPCs, whereas no leakage occurred in the BCPCs in the three months after their gravimetric preparation. The BCPCs maintained no leakage even 10 months after their preparation, whereas the PCPCs showed significantly increasing leakage during the same period.

Assessment of the aroma impact of major odor-active thiols in pan-roasted white sesame seeds by calculation of odor activity values.

PubMed

Tamura, Hitoshi; Fujita, Akira; Steinhaus, Martin; Takahisa, Eisuke; Watanabe, Hiroyuki; Schieberle, Peter

2011-09-28

Eleven odor-active thiols, namely, 2-methyl-1-propene-1-thiol, (Z)-3-methyl-1-butene-1-thiol, (E)-3-methyl-1-butene-1-thiol, (Z)-2-methyl-1-butene-1-thiol, (E)-2-methyl-1-butene-1-thiol, 2-methyl-3-furanthiol, 3-mercapto-2-pentanone, 2-mercapto-3-pentanone, 4-mercapto-3-hexanone, 3-mercapto-3-methylbutyl formate, and 2-methyl-3-thiophenethiol, recently identified in an extract prepared from white sesame seeds, were quantitated in sesame using stable isotope dilution analyses. For that purpose, the following deuterium-labeled compounds were synthesized and used as internal standards in the quantitation assays: [2H6]-2-methyl-1-propene-1-thiol, [2H3]-(E)- and [2H3]-(Z)-2-methyl-1-butene-1-thiol, [2H3]-2-methyl-3-furanthiol, [2H2]-3-mercapto-2-pentanone, [2H3]-4-mercapto-3-hexanone, [2H6]-3-mercapto-3-methylbutyl formate, and [2H3]-2-methyl-3-thiophenethiol. On the basis of the results obtained, odor activity values (OAVs) were calculated as ratio of the concentration and odor threshold of the individual compounds in cooking oil. According to their high OAVs, particularly the 3-methyl-1-butene-1-thiols (OAV: 2400) and the 2-methyl-1-butene-1-thiols (OAV: 960) were identified as the most odor-active compounds in pan-roasted white sesame seeds. These compounds were therefore suggested to be mainly responsible for the characteristic but rather unstable sulfury aroma of freshly pan-roasted white sesame seeds.

Metabolic engineering for the high-yield production of isoprenoid-based C 5 alcohols in E. coli

DOE Office of Scientific and Technical Information (OSTI.GOV)

George, Kevin W.; Thompson, Mitchell G.; Kang, Aram

2015-06-08

Branched five carbon (C 5) alcohols are attractive targets for microbial production due to their desirable fuel properties and importance as platform chemicals. In this study, we engineered a heterologous isoprenoid pathway in E. coli for the high-yield production of 3-methyl-3-buten-1-ol, 3-methyl-2-buten-1-ol, and 3-methyl-1-butanol, three C 5 alcohols that serve as potential biofuels. We first constructed a pathway for 3-methyl-3-buten-1-ol, where metabolite profiling identified NudB, a promiscuous phosphatase, as a likely pathway bottleneck. We achieved a 60% increase in the yield of 3-methyl-3-buten-1-ol by engineering the Shine-Dalgarno sequence of nudB, which increased protein levels by 9-fold and reduced isopentenyl diphosphatemore » (IPP) accumulation by 4-fold. To further optimize the pathway, we adjusted mevalonate kinase (MK) expression and investigated MK enzymes from alternative microbes such as Methanosarcina mazei. Next, we expressed a fusion protein of IPP isomerase and the phosphatase (Idi1~NudB) along with a reductase (NemA) to diversify production to 3-methyl-2-buten-1-ol and 3-methyl-1-butanol. Lastly, we used an oleyl alcohol overlay to improve alcohol recovery, achieving final titers of 2.23 g/L of 3-methyl-3-buten-1-ol (~70% of pathway-dependent theoretical yield), 150 mg/L of 3-methyl-2-buten-1-ol, and 300 mg/L of 3-methyl-1-butanol.« less

Metabolic engineering for the high-yield production of isoprenoid-based C5 alcohols in E. coli

PubMed Central

George, Kevin W.; Thompson, Mitchell G.; Kang, Aram; Baidoo, Edward; Wang, George; Chan, Leanne Jade G.; Adams, Paul D.; Petzold, Christopher J.; Keasling, Jay D.; Soon Lee, Taek

2015-01-01

Branched five carbon (C5) alcohols are attractive targets for microbial production due to their desirable fuel properties and importance as platform chemicals. In this study, we engineered a heterologous isoprenoid pathway in E. coli for the high-yield production of 3-methyl-3-buten-1-ol, 3-methyl-2-buten-1-ol, and 3-methyl-1-butanol, three C5 alcohols that serve as potential biofuels. We first constructed a pathway for 3-methyl-3-buten-1-ol, where metabolite profiling identified NudB, a promiscuous phosphatase, as a likely pathway bottleneck. We achieved a 60% increase in the yield of 3-methyl-3-buten-1-ol by engineering the Shine-Dalgarno sequence of nudB, which increased protein levels by 9-fold and reduced isopentenyl diphosphate (IPP) accumulation by 4-fold. To further optimize the pathway, we adjusted mevalonate kinase (MK) expression and investigated MK enzymes from alternative microbes such as Methanosarcina mazei. Next, we expressed a fusion protein of IPP isomerase and the phosphatase (Idi1~NudB) along with a reductase (NemA) to diversify production to 3-methyl-2-buten-1-ol and 3-methyl-1-butanol. Finally, we used an oleyl alcohol overlay to improve alcohol recovery, achieving final titers of 2.23 g/L of 3-methyl-3-buten-1-ol (~70% of pathway-dependent theoretical yield), 150 mg/L of 3-methyl-2-buten-1-ol, and 300 mg/L of 3-methyl-1-butanol. PMID:26052683

Theoretical Kinetics Analysis for $$\\dot{H}$$ Atom Addition to 1,3-Butadiene and Related Reactions on the $$\\dot{C}$$ 4H 7 Potential Energy Surface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Yang; Klippenstein, Stephen J.; Zhou, Chong-Wen

The oxidation chemistry of the simplest conjugated hydrocarbon, 1,3-butadiene, can provide a first step in understanding the role of poly-unsaturated hydrocarbons in combustion and, in particular, an understanding of their contribution towards soot formation. Based on our previous work on propene and the butene isomers (1-, 2- and isobutene), it was found that the reaction kinetics of H-atom addition to the C=C double bond plays a significant role in fuel consumption kinetics and influences the predictions of high-temperature ignition delay times, product species concentrations and flame speed measurements. In this study, the rate constants and thermodynamic properties formore » $$\\dot{H}$$-atom addition to 1,3-butadiene and related reactions on the $$\\dot{C}$$ 4H 7 potential energy surface have been calculated using two different series of quantum chemical methods and two different kinetic codes. Excellent agreement is obtained between the two different kinetics codes. The calculated results including zero point energies, single point energies, rate constants, barrier heights and thermochemistry are systematically compared among the two quantum chemical methods. 1-methylallyl ($$\\dot{C}$$ 4H 71-3) and 3-buten-1- yl ($$\\dot{C}$$ 4H 71-4) radicals and C 2H 4 + $$\\dot{C}$$2H3 are found to be the most important channels and reactivity promoting products, respectively. We calculated that terminal addition is dominant (> 80%) compared to internal $$\\dot{H}$$-atom addition at all temperatures in the range 298 – 2000 K. However, this dominance decreases with increasing temperature. The calculated rate constants for the bimolecular reaction C 4H 6 + $$\\dot{H}$$ → products and C 2H 4 + $$\\dot{C}$$ 2H 3 → products are in excellent agreement with both experimental and theoretical results from the literature. For selected C 4 species the calculated thermochemical values are also in good agreement with literature data. In addition, the rate constants for H-atom abstraction by $$\\dot{H}$$ atoms have also been calculated, and it is found that abstraction from the central carbon atoms is the dominant channel (> 70%) at temperatures in the range 298 – 2000 K. Lastly, by incorporating our calculated rate constants for both H-atom addition and abstraction into our recently developed 1,3-butadiene model, we show that laminar flame speed predictions are significantly improved, emphasizing the value of this study.« less

Calculational and Experimental Investigations of the Pressure Effects on Radical - Radical Cross Combinations Reactions: C2H5 + C2H3

NASA Technical Reports Server (NTRS)

Fahr, Askar; Halpern, Joshua B.; Tardy, Dwight C.

2007-01-01

Pressure-dependent product yields have been experimentally determined for the cross-radical reaction C2H5 + C2H3. These results have been extended by calculations. It is shown that the chemically activated combination adduct, 1-C4H8*, is either stabilized by bimolecular collisions or subject to a variety of unimolecular reactions including cyclizations and decompositions. Therefore the "apparent" combination/disproportionation ratio exhibits a complex pressure dependence. The experimental studies were performed at 298 K and at selected pressures between about 4 Torr (0.5 kPa) and 760 Torr (101 kPa). Ethyl and vinyl radicals were simultaneously produced by 193 nm excimer laser photolysis of C2H5COC2H3 or photolysis of C2H3Br and C2H5COC2H5. Gas chromatograph/mass spectrometry/flame ionization detection (GC/MS/FID) were used to identify and quantify the final reaction products. The major combination reactions at pressures between 500 (66.5 kPa) and 760 Torr are (1c) C2H5 + C2H3 yields 1-butene, (2c) C2H5 + C2H5 yields n-butane, and (3c) C2H3 + C2H3 yields 1,3-butadiene. The major products of the disproportionation reactions are ethane, ethylene, and acetylene. At moderate and lower pressures, secondary products, including propene, propane, isobutene, 2-butene (cis and trans), 1-pentene, 1,4-pentadiene, and 1,5-hexadiene are also observed. Two isomers of C4H6, cyclobutene and/or 1,2-butadiene, were also among the likely products. The pressure-dependent yield of the cross-combination product, 1-butene, was compared to the yield of n-butane, the combination product of reaction (2c), which was found to be independent of pressure over the range of this study. The [ 1-C4H8]/[C4H10] ratio was reduced from approx.1.2 at 760 Torr (101 kPa) to approx.0.5 at 100 Torr (13.3 kPa) and approx.0.1 at pressures lower than about 5 Torr (approx.0.7 kPa). Electronic structure and RRKM calculations were used to simulate both unimolecular and bimolecular processes. The relative importance of C-C and C-H bond ruptures, cyclization, decyclization, and complex decompositions are discussed in terms of energetics and structural properties. The pressure dependence of the product yields were computed and dominant reaction paths in this chemically activated system were determined. Both modeling and experiment suggest that the observed pressure dependence of [1-C4H8]/[C4H10] is due to decomposition of the chemically activated combination adduct 1-C4H8* in which the weaker allylic C-C bond is broken: H2C=CHCH2CH3 yields C3H5 + CH3. This reaction occurs even at moderate pressures of approx.200 Torr (26 kPa) and becomes more significant at lower pressures. The additional products detected at lower pressures are formed from secondary radical-radical reactions involving allyl, methyl, ethyl, and vinyl radicals. The modeling studies have extended the predictions of product distributions to different temperatures (200-700 K) and a wider range of pressures (10(exp -3) - 10(exp 5) Torr). These calculations indicate that the high-pressure [1-C4H8]/[C4H10] yield ratio is 1.3 +/- 0.1.

Direct conversion of bio-ethanol to isobutene on nanosized Zn(x)Zr(y)O(z) mixed oxides with balanced acid-base sites.

PubMed

Sun, Junming; Zhu, Kake; Gao, Feng; Wang, Chongmin; Liu, Jun; Peden, Charles H F; Wang, Yong

2011-07-27

We report the design and synthesis of nanosized Zn(x)Zr(y)O(z) mixed oxides for direct and high-yield conversion of bio-ethanol to isobutene (~83%). ZnO is addded to ZrO(2) to selectively passivate zirconia's strong Lewis acidic sites and weaken Brönsted acidic sites, while simultaneously introducing basicity. As a result, the undesired reactions of bio-ethanol dehydration and acetone polymerization/coking are suppressed. Instead, a surface basic site-catalyzed ethanol dehydrogenation to acetaldehyde, acetaldehyde to acetone conversion via a complex pathway including aldol-condensation/dehydrogenation, and a Brönsted acidic site-catalyzed acetone-to-isobutene reaction pathway dominates on the nanosized Zn(x)Zr(y)O(z) mixed oxide catalyst, leading to a highly selective process for direct conversion of bio-ethanol to isobutene.

40 CFR 60.667 - Chemicals affected by subpart NNN.

Code of Federal Regulations, 2012 CFR

2012-07-01

... fractions n-Butane 106-97-8 1,4-Butanediol 110-63-4 Butanes, mixed 1-Butene 106-98-9 2-Butene 25167-67-3 Butenes, mixed n-Butyl acetate 123-86-4 Butyl acrylate 141-32-2 n-Butyl alcohol 71-36-3 sec-Butyl alcohol... Diethanolamine 111-42-2 Diethylbenzene 25340-17-4 Diethylene glycol 111-46-6 Di-n-heptyl-n-nonyl undecyl...

Low Leachable Container System Consisting of a Polymer-Based Syringe with Chlorinated Isoprene Isobutene Rubber Plunger Stopper.

PubMed

Kiminami, Hideaki; Takeuchi, Katsuyuki; Nakamura, Koji; Abe, Yoshihiko; Lauwers, Philippe; Dierick, William; Yoshino, Keisuke; Suzuki, Shigeru

2015-01-01

A 36 month leachable study on water for injection in direct contact within a polymer-based prefillable syringe consisting of a cyclo olefin polymer barrel, a chlorinated isoprene isobutene rubber plunger stopper, a polymer label attached on the barrel, and a secondary packaging was conducted at 25 ± 2 °C and 60 ± 5% relative humidity. Through the various comparison studies, no difference in the leachable amounts was observed between this polymer-based prefilled syringe and a glass bottle as a blank sample reference by 36 months. No influence on the leachables study outcome was noted from the printed label and/or label adhesive or from the secondary packaging. In an additional study, no acrylic acid used as the label adhesive leachable was detected by an extended storage for 45 months at 25 ± 2 °C and 60 ± 5% relative humidity as a worst case. To obtain more details, a comparison extractable study was conducted between a cyclo olefin polymer barrel and a glass barrel. In addition, chlorinated isoprene isobutene rubber and bromo isoprene isobutene rubber were compared. As a result, no remarkable difference was found in the organic extractables for syringe barrels. On the other hand, in the case of element extractable analysis, the values for the cyclo olefin polymer barrel were lower than that for the glass barrel. For the plunger stoppers, the chlorinated isoprene isobutene rubber applied in this study was showing a lower extractable profile as compared to the bromo isoprene isobutene rubber, both for organic and element extractables. In conclusion, the proposed polymer-based prefillable syringe system has great potential and represents a novel alternative that can achieve very low level extractable profiles and can bring additional value to the highly sensitive biotech drug market. A 36 month leachable study on water for injection in direct contact within a cyclo olefin polymer barrel and chlorinated isoprene isobutene rubber plunger stopper that has a polymer label attached to the barrel and is wrapped into a secondary packaging was conducted at 25 °C and 60% relative humidity. Through the various comparison studies, no difference in the leachable amounts was observed between polymer-based prefilled syringes and a glass bottle as a blank sample reference by 36 months. No influences on the leachables study outcome were noted from the secondary packaging. To obtain more details, a comparison extractable study was conducted between the cyclo olefin polymer and the glass barrel. In addition, chlorinated isoprene isobutene rubber and bromo isoprene isobutene rubber plunger stoppers were compared as well. As a result, no remarkable difference was found in the organic extractables for barrels. As for element extractable analysis, the values for the cyclo olefin polymer barrel were lower than that for the glass barrel. For the plunger stoppers, the chlorinated isoprene isobutene rubber applied in this study was showing a lower extractable profile as compared to the bromo isoprene isobutene rubber, both for organic and element extractables. In conclusion, the proposed polymer-based prefillable syringe system has great potential and represents a novel alternative that can achieve very low level extractable profiles and can bring additional value to the highly sensitive biotech drug market. © PDA, Inc. 2015.

Microcosm Studies to Evaluate Aerobic Cometabolism of Low Concentrations of 1,4-Dioxane by Isobutane-utilizing Microorganisms in the Presence of Chlorinated Solvent Co-contaminants

NASA Astrophysics Data System (ADS)

Rolston, H. M.; Azizian, M.; Hyman, M. R.; Semprini, L.

2015-12-01

Due to its use as a stabilizer for chlorinated solvents, 1,4-dioxane (1,4D), a probable human carcinogen, is a common co-contaminant in solvent spills at industrial and military sites and landfills. Its persistence in large groundwater plumes at low concentrations makes it a relevant candidate for in-situ bioremediation via cometabolism. Microcosm studies are being performed to evaluate the capability of aerobic microorganisms to cometabolize mixtures of 1,4D and chlorinated solvents, such as trichloroethylene (TCE), 1,1,1-trichloroethane (1,1,1TCA), and 1,1-dichloroethene (1,1DCE), with isobutane as the primary substrate. Microcosms were constructed using aquifer solids from Fort Carson, Colorado, a site contaminated with 1,4D and TCE, to assess the isobutane uptake and transformation of 1,4D and chlorinated solvents by microorganisms native to the site. Additional microcosms were augmented with Rhodococcus rhodochrous, a bacterium shown to cometabolize 1,4D and chlorinated solvents. Results indicate that native microcosms cometabolized 1,4D upon stimulation with isobutane after a lag period of about 15 days. TCE was also transformed, but at significantly slower rates. The presence of 1,4D and TCE at 500 and 300 ppb, respectively, did not inhibit the growth of native microorganisms on isobutane, with isobutane uptake and 1,4D transformation occurring simultaneously. Bioaugmented microcosms transformed 1,4D immediately after inoculation with R. rhodochrous. Tests in bioaugmented microorganisms indicated that the presence of TCE at low concentrations inhibits but does not block the transformation of 1,4D. Results from the microcosms will be used to design field tests to be performed at Fort Carson. Additional microcosm studies will compare the stimulation of native and bioaugmented microcosms and the transformation of mixtures of 1,4D, 1,1,1TCA and 1,1DCE. Molecular methods will analyze the monoxygenase enzymes expressed in the native and bioaugmented microcosms.

Characterizations of volatile organic compounds (VOCs) from vehicular emissions at roadside environment: The first comprehensive study in Northwestern China

NASA Astrophysics Data System (ADS)

Li, Bowei; Ho, Steven Sai Hang; Xue, Yonggang; Huang, Yu; Wang, Liqin; Cheng, Yan; Dai, Wenting; Zhong, Haobin; Cao, Junji; Lee, Shuncheng

2017-07-01

Vehicular emission (VE) is one of the important anthropogenic sources for ground-level volatile organic compounds (VOCs) in both urban and suburban areas. A first comprehensive campaign was conducted at an urban roadside in Xi'an, China in summer, 2016. A total of 57 VOCs, as known as critical surface ozone (O3) precursors, and other trace gases were measured simultaneously during the sampling period. Iso-pentane, a tracer of gasoline evaporation, was the most abundant VOC in the roadside samples, followed by isobutane and benzene, attributed to the largest composition (∼70%) of gasoline-fueled vehicles on the road. The molar ratio of toluene/benzene (T/B) in our study (0.36) is far lower than the range reported in other cities, indicating the stronger contributions from diesel emissions. The results of source apportionment achieved with positive matrix factorization (PMF) receptor model were highly consistent with the vehicles compositions, strongly evidenced that the precise characterization of the VE sources from those marker species. The degrees of individual compound contributed to O3 production were weighed by ozone formation potential (OFP). Propylene (20%), 1-butene (11%) and iso-pentane(10%) were the top three contributors at the roadside. The information of this study complements the VOCs database regarding to the VE sources in Northwestern China.

Preparation of mesoporous alumina particles by spray pyrolysis and application to double bond migration of 2-butene.

PubMed

Song, Ki Chang; Kim, Joo Hyun; Kim, Jin Han; Jung, Kyeong Youl; Park, Young-Kwon; Jeon, Jong-Ki

2011-07-01

The objective of the present study is to investigate the catalytic performance of mesoporous alumina that were prepared via spray pyrolysis for double bond migration from 2-butene to 1-butene. The mesoporous alumina particles were prepared via spray pyrolysis by changing the types of organic surfactants and Al precursors. The texture and acidic properties of mesoporous alumina were analyzed through N2 adsorption, SEM, ammonia-temperature programmed desorption, and FT-IR of adsorbed pyridine. The morphologies and texture properties of the mesoporous alumina were found to have been strongly influenced by the combination of the Al precursor and the structure-directing agents. The mesoporous alumina samples had two kinds of acidic sites: a Lewis acid site and a H-bonded weak acid site. 1-Butene was produced selectively through double bond migration of 2-butene over all of the mesoporous alumina catalysts. The catalyst prepared by using a chloride compound as an aluminium precursor and CTAC as a structure-directing agent showed the highest activity in the double bond migration of 2-butene, which was attributed to its large surface area and an overall high amount of acid sites.

Advanced Testing of Safe-Solvent Replacements for CFC-113 for Use in Cleaning Oxygen Systems

DTIC Science & Technology

2005-06-01

2 -(trifluoromethyl)-3,3,3- trifluoropropene 2 Reactions/28 Impacts Failed 4-bromo- 3 - chloro -3,4,4-trifluoro-1-butene 2 ...bromo- 3 - chloro -3,4,4-trifluoro-1-butene, CH2=CH-CFCl-CF2Br § 1- chloro -2,2,2-trifluoroethyl difluoromethyl ether, CHF2-O-CHCl-CF3 § 2 - chloro -1,1,2...3,3,3- trifluoropropene 725°F Recommended 4-bromo- 3 - chloro -3,4,4-trifluoro-1-butene 378°F Caution 1- chloro -2,2,2-trifluoroethyl difluoromethyl ether

Infrared absorption of 1-chloro-2-methyl-2-propyl [⋅C(CH3)2CH2Cl] and 2-chloro-2-methylpropyl [⋅CH2C(CH3)2Cl] radicals produced in the addition reactions of Cl with isobutene (i-C4H8) in solid para-hydrogen.

PubMed

Chou, Ching-Yin; Lee, Yuan-Pern

2016-10-07

The addition reactions of chlorine atom with isobutene (i-C 4 H 8 ) in solid para-hydrogen (p-H 2 ) were investigated with infrared (IR) absorption spectra. When a p-H 2 matrix containing Cl 2 and isobutene was irradiated with ultraviolet light at 365 nm, intense lines in a set at 534.5, 1001.0, 1212.9, 1366.0, 2961.6, and 2934.7 cm -1 , and several weaker others due to the 1-chloro-2-methyl-2-propyl radical, ⋅ C(CH 3 ) 2 CH 2 Cl, and those in a second set including intense ones at 642.7, 799.2, 1098.2, 1371.8, and 3027.3 cm -1 due to the 2-chloro-2-methylpropyl radical, ⋅ CH 2 C(CH 3 ) 2 Cl, appeared; the ratio of ⋅ C(CH 3 ) 2 CH 2 Cl to ⋅ CH 2 C(CH 3 ) 2 Cl was approximately (3 ± 1):1. The observed wavenumbers and relative intensities agree with the vibrational wavenumbers and IR intensities predicted with the B3PW91/aug-cc-pVTZ method. That the Cl atom adds to both carbons of the C=C bond of isobutene with the terminal site slightly favored is consistent with the energies of products predicted theoretically, but is in contrast to the reaction of Cl + propene in solid p-H 2 in which the addition of Cl to mainly the central C atom was previously reported. The role of the p-H 2 matrix in affecting the reaction paths is discussed. Absorption lines of the complex i-C 4 H 8 ⋅Cl 2 and the dichloro-product anti-1,2-dichloro-2-methylpropane, a-CH 2 ClCCl(CH 3 ) 2 , are also characterized.

Cobalt Oxide on N-Doped Carbon for 1-Butene Oligomerization to Produce Linear Octenes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Dongting; Xu, Zhuoran; Chada, Joseph P.

Cobalt oxide supported on N-doped carbon catalysts were investigated for 1-butene oligomerization. The materials were synthesized by treating activated carbon with nitric acid and subsequently with NH3 at 200, 400, 600, and 800 °C, followed by impregnation with cobalt. The 1-butene oligomerization selectivity increased with ammonia treatment temperature of the carbon support. The oligomerization selectivity of cobalt oxide on N-doped carbon synthesized at 800 °C (800A-CoOx/N-C) is 2.6 times higher than previously reported cobalt oxide on N-doped carbon synthesized with NH4OH (2A-CoOx/N-C). Over 70% of the butene dimers were linear C8 olefins for all catalysts. The oligomerization selectivity increased withmore » 1-butene conversion. The catalysts were characterized by elemental analysis, N2 adsorption, X-ray diffraction (XRD), X-ray absorption spectroscopy (XAS), and X-ray photoelectron spectroscopy (XPS). The nitrogen content of the catalysts increases with ammonia treatment temperature as confirmed by elemental analysis. The surface content of pyridinic nitrogen with a binding energy of 398.4 ± 0.1 eV increased with ammonia treatment temperature as evidenced by deconvolution of N 1s XPS spectra.« less

Microwave-assisted direct synthesis of butene from high-selectivity methane

NASA Astrophysics Data System (ADS)

Lu, Yi-heng; Li, Kang; Lu, Yu-wei

2017-12-01

Methane was directly converted to butene liquid fuel by microwave-induced non-oxidative catalytic dehydrogenation under 0.1-0.2 MPa. The results show that, under microwave heating in a two-stage fixed-bed reactor, in which nickel powder and NiOx-MoOy/SiO2 are used as the catalyst, the methane-hydrogen mixture is used as the raw material, with no acetylene detected. The methane conversion is more than 73.2%, and the selectivity of methane to butene is 99.0%. Increasing the hydrogen/methane feed volume ratio increases methane conversion and selectivity. Gas chromatography/electron impact ionization/mass spectrometry chromatographic analysis showed that the liquid fuel produced by methane dehydrogenation oligomerization contained 89.44% of butene, and the rest was acetic acid, ethanol, butenol and butyric acid, and the content was 1.0-3.0 wt%.

Microwave-assisted direct synthesis of butene from high-selectivity methane

PubMed Central

Li, Kang; Lu, Yu-wei

2017-01-01

Methane was directly converted to butene liquid fuel by microwave-induced non-oxidative catalytic dehydrogenation under 0.1–0.2 MPa. The results show that, under microwave heating in a two-stage fixed-bed reactor, in which nickel powder and NiOx–MoOy/SiO2 are used as the catalyst, the methane–hydrogen mixture is used as the raw material, with no acetylene detected. The methane conversion is more than 73.2%, and the selectivity of methane to butene is 99.0%. Increasing the hydrogen/methane feed volume ratio increases methane conversion and selectivity. Gas chromatography/electron impact ionization/mass spectrometry chromatographic analysis showed that the liquid fuel produced by methane dehydrogenation oligomerization contained 89.44% of butene, and the rest was acetic acid, ethanol, butenol and butyric acid, and the content was 1.0–3.0 wt%. PMID:29308261

Photodissociation dynamics of propanal and isobutanal: The Norrish Type I pathway

NASA Astrophysics Data System (ADS)

Harrison, Aaron W.; Kable, Scott H.

2018-04-01

The Norrish Type I photodissociation of two aliphatic aldehydes, propanal and isobutanal, has been investigated using velocity-map imaging. The HCO photoproduct of this reaction was probed using a 1+1 resonance-enhanced multiphoton ionization scheme via the 3p2Π Rydberg state. The velocity map images of HCO+ were collected across a range of photolysis energies for both species from 30 500 to 33 000 cm-1 (λ = 312-327 nm). The corresponding translational energy distributions show that the majority of the available energy goes into the translational motion of the products (55%-68%) with this fraction increasing as the T1 barrier is approached. Analysis of the translational energy distributions was also used to determine the aldehyde α C-C bond dissociation energies which were found to be 339.8 ± 2.5 and 331.2 ± 2.5 kJ/mol for propanal and isobutanal, respectively. These values were also found to be in good agreement with the computed dissociation energies using G4 and CCSD(T)/aug-cc-pVTZ//M062X/aug-cc-pVTZ levels of theory. Furthermore, these dissociation energies, combined with the known ΔfH (0 K) of the reaction products, provided the ΔfH (0 K) of propanal and isobutanal which were calculated to be -167.3 ± 2.5 and -184.0 ± 2.5 kJ/mol, respectively.

21 CFR 184.1165 - n-Butane and iso-butane.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false n-Butane and iso-butane. 184.1165 Section 184.1165 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD... Listing of Specific Substances Affirmed as GRAS § 184.1165 n-Butane and iso-butane. (a) n-Butane and iso...

21 CFR 184.1165 - n-Butane and iso-butane.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true n-Butane and iso-butane. 184.1165 Section 184.1165 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD... Listing of Specific Substances Affirmed as GRAS § 184.1165 n-Butane and iso-butane. (a) n-Butane and iso...

Low-Temperature Synchrotron Photoionization Study of 2-Methyl-3-buten-2-ol (MBO) Oxidation Initiated by O(3P) Atoms in the 298-650 K Range.

PubMed

Fathi, Yasmin; Price, Chelsea; Meloni, Giovanni

2017-04-20

This work studies the oxidation of 2-methyl-3-buten-2-ol initiated by O( 3 P) atoms. The oxidation was investigated at room temperature, 550, and 650 K. Using the synchrotron radiation from the Advanced Light Source (ALS) of the Lawrence Berkley National Laboratory, reaction intermediates and products were studied by multiplexed photoionization mass spectrometry. Mass-to-charge ratios, kinetic time traces, photoionization spectra, and adiabatic ionization energies for each primary reaction species were obtained and used to characterize their identity. Using electronic structure calculations, potential energy surface scans of the different species produced throughout the oxidation were examined and presented in this paper to further validate the primary chemistry occurring. Branching fractions of primary products at all three temperatures were also provided. At room temperature only three primary products formed: ethenol (26.6%), acetaldehyde (4.2%), and acetone (53.4%). At 550 and 650 K the same primary products were observed in addition to propene (5.1%, 11.2%), ethenol (18.1%, 2.8%), acetaldehyde (8.9%, 5.7%), cyclobutene (1.6%, 10.8%), 1-butene (2.0%, 10.9%), trans-2-butene (3.2%, 23.1%), acetone (50.4%, 16.8%), 3-penten-2-one (1.0%, 11.5%), and 3-methyl-2-butenal (0.9%, 2.5%), where the first branching fraction value in parentheses corresponds to the 550 K data. At the highest temperature, a small amount of propyne (1.0%) was also observed.

Identification of novel aroma-active thiols in pan-roasted white sesame seeds.

PubMed

Tamura, Hitoshi; Fujita, Akira; Steinhaus, Martin; Takahisa, Eisuke; Watanabe, Hiroyuki; Schieberle, Peter

2010-06-23

Screening for aroma-active compounds in an aroma distillate obtained from freshly pan-roasted sesame seeds by aroma extract dilution analysis revealed 32 odorants in the FD factor range of 2-2048, 29 of which could be identified. The highest FD factors were found for the coffee-like smelling 2-furfurylthiol, the caramel-like smelling 4-hydroxy-2,5-dimethyl-3(2H)-furanone, the coffee-like smelling 2-thenylthiol (thiophen-2-yl-methylthiol), and the clove-like smelling 2-methoxy-4-vinylphenol. In addition, 9 odor-active thiols with sulfurous, meaty, and/or catty, black-currant-like odors were identified for the first time in roasted sesame seeds. Among them, 2-methyl-1-propene-1-thiol, (Z)-3-methyl-1-butene-1-thiol, (E)-3-methyl-1-butene-1-thiol, (Z)-2-methyl-1-butene-1-thiol, (E)-2-methyl-1-butene-1-thiol, and 4-mercapto-3-hexanone were previously unknown as food constituents. Their structures were confirmed by comparing their mass spectra and retention indices as well as their sensory properties with those of synthesized reference compounds. The relatively unstable 1-alkene-1-thiols represent a new class of food odorants and are suggested as the key contributors to the characteristic, but quickly vanishing, aroma of freshly ground roasted sesame seeds.

21 CFR 177.1430 - Isobutylene-butene copolymers.

Code of Federal Regulations, 2014 CFR

2014-04-01

...: Isobutylene-butene copolymers Molecular weight (range) Viscosity (range) Maximum bromine value 1. Used as.../federal_register/code_of_federal_regulations/ibr_locations.html. (2) Viscosity. Viscosity shall be determined by ASTM method D445-74, “Test for Kinematic Viscosity of Transparent and Opaque Liquids,” which is...

Canopy Level Emissions of 2-methyl-3-buten-2-ol, monoterpenes, and sesquiterpenes from a Pinus taeda Experimental Plantation

EPA Science Inventory

Emissions of biogenic volatile organic compounds (BVOC) observed during 2007 from a Pinus taeda experimental plantation in Central North Carolina are compared with model estimates from MEGAN 2.1. Relaxed Eddy Accumulation (REA) estimates of 2-methyl-3-buten-2-ol (MBO) fluxes are ...

A sedge plant as the source of Kangaroo Island propolis rich in prenylated p-coumarate ester and stilbenes.

PubMed

Duke, Colin C; Tran, Van H; Duke, Rujee K; Abu-Mellal, Abdallah; Plunkett, George T; King, Douglas I; Hamid, Kaiser; Wilson, Karen L; Barrett, Russell L; Bruhl, Jeremy J

2017-02-01

Propolis samples from Kangaroo Island, South Australia, were investigated for chemical constituents using high-field nuclear magnetic resonance spectral profiling. A type of propolis was found containing a high proportion of prenylated hydroxystilbenes. Subsequently, the botanical origin of this type of propolis was identified using a beehive propolis depletion method and analysis of flora. Ligurian honey bees, Apis mellifera ligustica Spinola, were found to produce propolis from resin exuded by the Australian native sedge plant Lepidosperma sp. Montebello (Cyperaceae). The plants, commonly known as sword sedge, were found to have resin that matched with the propolis samples identified as the most abundant propolis type on the island containing C- and O-prenylated tetrahydroxystilbenes (pTHOS) in addition to a small amount of prenylated p-coumarate. The isolation of five pTHOS not previously characterized are reported: (E)-4-(3-methyl-2-buten-1-yl)-3,4',5-trihydroxy-3'-methoxystilbene, (E)-2,4-bis(3-methyl-2-buten-1-yl)-3,3',4',5-tetrahydroxystilbene, (E)-2-(3-methyl-2-buten-1-yl)-3-(3-methyl-2-butenyloxy)-3',4',5-trihydroxystilbene, (E)-2,6-bis(3-methyl-2-buten-1-yl)-3,3',5,5'-tetrahydroxystilbene and (E)-2,6-bis(3-methyl-2-buten-1-yl)-3,4',5-trihydroxy-3'-methoxystilbene. A National Cancer Institute 60 human cell line anticancer screen of three of these compounds showed growth inhibitory activity. The large Australasian genus Lepidosperma is identified as a valuable resource for the isolation of substances with medicinal potential. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Mechanical and Thermal Properties of Polypropylene Composites Reinforced with Lignocellulose Nanofibers Dried in Melted Ethylene-Butene Copolymer

PubMed Central

Iwamoto, Shinichiro; Yamamoto, Shigehiro; Lee, Seung-Hwan; Ito, Hirokazu; Endo, Takashi

2014-01-01

Lignocellulose nanofibers were prepared by the wet disk milling of wood flour. First, an ethylene-butene copolymer was pre-compounded with wood flour or lignocellulose nanofibers to prepare master batches. This process involved evaporating the water of the lignocellulose nanofiber suspension during compounding with ethylene-butene copolymer by heating at 105 °C. These master batches were compounded again with polypropylene to obtain the final composites. Since ethylene-butene copolymer is an elastomer, its addition increased the impact strength of polypropylene but decreased the stiffness. In contrast, the wood flour- and lignocellulose nanofiber-reinforced composites showed significantly higher flexural moduli and slightly higher flexural yield stresses than did the ethylene-butene/polypropylene blends. Further, the wood flour composites exhibited brittle fractures during tensile tests and had lower impact strengths than those of the ethylene-butene/polypropylene blends. On the other hand, the addition of the lignocellulose nanofibers did not decrease the impact strength of the ethylene-butene/polypropylene blends. Finally, the addition of wood flour and the lignocellulose nanofibers increased the crystallization temperature and crystallization rate of polypropylene. The increases were more remarkable in the case of the lignocellulose nanofibers than for wood flour. PMID:28788222

Temperature control during regeneration of activated carbon fiber cloth with resistance-feedback.

PubMed

Johnsen, David L; Rood, Mark J

2012-10-16

Electrothermal swing adsorption (ESA) of organic compounds from gas streams with activated carbon fiber cloth (ACFC) reduces emissions to the atmosphere and recovers feedstock for reuse. Local temperature measurement (e.g., with a thermocouple) is typically used to monitor/control adsorbent regeneration cycles. Remote electrical resistance measurement is evaluated here as an alternative to local temperature measurement. ACFC resistance that was modeled based on its physical properties was within 10.5% of the measured resistance values during electrothermal heating. Resistance control was developed based on this measured relationship and used to control temperature to within 2.3% of regeneration set-point temperatures. Isobutane-laden adsorbent was then heated with resistance control. After 2 min of heating, the temperature of the adsorbent with isobutane was 13% less than the adsorbent without isobutane. This difference decreased to 2.1% after 9 min of heating, showing desorption of isobutane. An ACFC cartridge was also heated to 175 °C for 900 cycles with its resistance and adsorption capacity values remaining within 3% and 2%, respectively. This new method to control regeneration power application based on rapid sensing of the adsorbent's resistance removes the need for direct-contact temperature sensors providing a simple, cost-efficient, and long-term regeneration technique for ESA systems.

Acetone in the atmosphere: Distribution, sources, and sinks

NASA Technical Reports Server (NTRS)

Singh, H. B.; O'Hara, D.; Herlth, D.; Sachse, W.; Blake, D. R.; Bradshaw, J. D.; Kanakidou, M.; Crutzen, P. J.

1994-01-01

Acetone (CH3COCH3) was found to be the dominant nonmethane organic species present in the atmosphere sampled primarily over eastern Canada (0-6 km, 35 deg-65 deg N) during ABLE3B (July to August 1990). A concentration range of 357 to 2310 ppt (= 10(exp -12) v/v) with a mean value of 1140 +/- 413 ppt was measured. Under extremely clean conditions, generally involving Arctic flows, lowest (background) mixing ratios of 550 +/- 100 ppt were present in much of the troposphere studied. Correlations between atmospheric mixing ratios of acetone and select species such as C2H2, CO, C3H8, C2Cl4 and isoprene provided important clues to its possible sources and to the causes of its atmospheric variability. Biomass burning as a source of acetone has been identified for the first time. By using atmospheric data and three-dimensional photochemical models, a global acetone source of 40-60 Tg (= 10(exp 12) g)/yr is estimated to be present. Secondary formation from the atmospheric oxidation of precursor hydrocarbons (principally propane, isobutane, and isobutene) provides the single largest source (51%). The remainder is attributable to biomass burning (26%), direct biogenic emissions (21%), and primary anthropogenic emissions (3%). Atmospheric removal of acetone is estimated to be due to photolysis (64%), reaction with OH radicals (24%), and deposition (12%). Model calculations also suggest that acetone photolysis contributed significantly to PAN formation (100-200 ppt) in the middle and upper troposphere of the sampled region and may be important globally. While the source-sink equation appears to be roughly balanced, much more atmospheric and source data, especially from the southern hemisphere, are needed to reliably quantify the atmospheric budget of acetone.

Direct contact, binary fluid geothermal boiler

DOEpatents

Rapier, Pascal M.

1982-01-01

Energy is extracted from geothermal brines by direct contact with a working fluid such as isobutane which is immiscible with the brine in a geothermal boiler. The geothermal boiler provides a distributor arrangement which efficiently contacts geothermal brine with the isobutane in order to prevent the entrainment of geothermal brine in the isobutane vapor which is directed to a turbine. Accordingly the problem of brine carry-over through the turbine causes corrosion and scaling thereof is eliminated. Additionally the heat exchanger includes straightening vanes for preventing startup and other temporary fluctuations in the transitional zone of the boiler from causing brine carryover into the turbine. Also a screen is provided in the heat exchanger to coalesce the working fluid and to assist in defining the location of the transitional zone where the geothermal brine and the isobutane are initially mixed.

Direct contact, binary fluid geothermal boiler

DOEpatents

Rapier, P.M.

1979-12-27

Energy is extracted from geothermal brines by direct contact with a working fluid such as isobutane which is immiscible with the brine in a geothermal boiler. The geothermal boiler provides a distributor arrangement which efficiently contacts geothermal brine with the isobutane in order to prevent the entrainment of geothermal brine in the isobutane vapor which is directed to a turbine. Accordingly the problem of brine carryover through the turbine causing corrosion and scaling thereof is eliminated. Additionally the heat exchanger includes straightening vanes for preventing startup and other temporary fluctuations in the transitional zone of the boiler from causing brine carryover into the turbine. Also a screen is provided in the heat exchanger to coalesce the working fluid and to assist in defining the location of the transitional zone where the geothermal brine and the isobutane are initially mixed.

Quantitative determination of n-propane, iso-butane, and n-butane by headspace GC-MS in intoxications by inhalation of lighter fluid.

PubMed

Bouche, Marie-Paule L A; Lambert, Willy E; Van Bocxlaer, Jan F P; Piette, Michel H; De Leenheer, André P

2002-01-01

This report describes a fully elaborated and validated method for quantitation of the hydrocarbons n-propane, iso-butane, and n-butane in blood samples. The newly developed analytical procedure is suitable for both emergency cases and forensic medicine investigations. Its practical applicability is illustrated with a forensic blood sample after acute inhalative intoxication with lighter fluid; case history and toxicological findings are included. Identification and quantitation of the analytes were performed using static headspace extraction combined with gas chromatography-mass spectrometry. In order to reconcile the large gas volumes injected (0.5 mL) with the narrowbore capillary column and thus achieve preconcentration, cold trapping on a Tenax sorbent followed by flash desorption was applied. Adequate retention and separation were achieved isothermally at 35 degrees C on a thick-film capillary column. Sample preparation was kept to a strict minimum and involved simply adding 2.5 microL of a liquid solution of 1,1,2-trichlorotrifluoroethane in t-butyl-methylether as an internal standard to aliquots of blood in a capped vial. Standards were created by volumetric dilution departing from a gravimetrically prepared calibration gas mixture composed of 0.3% of n-propane, 0.7% of iso-butane, and 0.8% of n-butane in nitrogen. In the forensic blood sample, the following concentrations were measured: 90.0 microg/L for n-propane, 246 microg/L for iso-butane, and 846 microg/L for n-butane.

Biomineralization of 1,4-dioxane in Pure Culture, Microcosm, and Column Studies Using 13C Labeling

NASA Astrophysics Data System (ADS)

Rolston, H. M.; Azizian, M.; Hyman, M. R.; Semprini, L.

2016-12-01

1,4-dioxane (1,4-D), a probable human carcinogen at low (< 1ppb) concentrations, is a widely occurring groundwater contaminant due to its use as a stabilizer for chlorinated solvents. Aerobic cometabolism, the use of a primary substrate to induce the production of microbial enzymes capable of transforming contaminants into innocuous products, is a promising in-situ treatment strategy for 1,4-D because it has the potential to mineralize trace 1,4-D concentrations to carbon dioxide (CO2). Previous work has confirmed the bacterium Rhodococcus rhodochrous (strain ATCC 21198) will transform 1,4-D when grown on isobutane. In this study, 13C uniformly labeled 1,4-D was used to determine the extent to which strain ATCC 21198 biomineralizes 1,4-D to CO2. Batch experiments have been conducted with pure culture 21198 and in microcosms constructed with aquifer sediments. The rate of resting cell transformation of 1,4-D by ATCC 21198 was over 100 times faster than the rate of CO2 accumulation, indicating the presence of intermediates that were slowly mineralized to CO2 . In microcosms, the use of isobutane as a primary substrate effectively stimulated the native microbial community to transform 1,4-D. Microcosms were also bioaugmented with ATCC 21198. After an initial lag and subsequent additions of isobutane, transformation rates in the native microcosms approached those of the bioaugmented microcosms. Cometabolically active microbes survived several periods of starvation in all microcosms, and nutrient amendment allowed for sustained transformation rates. 13C labeled 1,4-D is currently being used to determine the rates and extents of biomineralization in the microcosms. Column studies are also being conducted to evaluate cometabolism and biominerazation potential of isobutane as a biostimulant and 21198 for bioaugmentation under geochemical and flow conditions more representative of in-situ bioremediation.

EMISSION OF 2-METHYL-3-BUTEN-2-OL BY PINES: A POTENTIALLY LARGE NATURAL SOURCE OF REACTIVE CARBON TO THE ATMOSPHERE

EPA Science Inventory

High rates of emission of 2-methyl-3-buten-2-ol (MBO) were measured from needles of several pine species. Emissions of MBO in the light were 1 to 2 orders of magnitude higher than emissions of monoterpenes and, in contrast to monoterpene emissions from pines, were absent in the d...

[Using 2-DCOS to identify the molecular spectrum peaks for the isomer in the multi-component mixture gases Fourier transform infrared analysis].

PubMed

Zhao, An-Xin; Tang, Xiao-Jun; Zhang, Zhong-Hua; Liu, Jun-Hua

2014-10-01

The generalized two-dimensional correlation spectroscopy and Fourier transform infrared were used to identify hydrocarbon isomers in the mixed gases for absorption spectra resolution enhancement. The Fourier transform infrared spectrum of n-butane and iso-butane and the two-dimensional correlation infrared spectrum of concentration perturbation were used for analysis as an example. The all band and the main absorption peak wavelengths of Fourier transform infrared spectrum for single component gas showed that the spectra are similar, and if they were mixed together, absorption peaks overlap and peak is difficult to identify. The synchronous and asynchronous spectrum of two-dimensional correlation spectrum can clearly identify the iso-butane and normal butane and their respective characteristic absorption peak intensity. Iso-butane has strong absorption characteristics spectrum lines at 2,893, 2,954 and 2,893 cm(-1), and n-butane at 2,895 and 2,965 cm(-1). The analysis result in this paper preliminary verified that the two-dimensional infrared correlation spectroscopy can be used for resolution enhancement in Fourier transform infrared spectrum quantitative analysis.

Weak interactions between water and clathrate-forming gases at low pressures

DOE PAGES

Thürmer, Konrad; Yuan, Chunqing; Kimmel, Greg A.; ...

2015-07-17

Using scanning probe microscopy and temperature programed desorption we examined the interaction between water and two common clathrate-forming gases, methane and isobutane, at low temperature and low pressure. Water co-deposited with up to 10 –1 mbar methane or 10 –5 mbar isobutane at 140 K onto a Pt(111) substrate yielded pure crystalline ice, i.e., the exposure to up to ~ 10 7 gas molecules for each deposited water molecule did not have any detectable effect on the growing films. Exposing metastable, less than 2 molecular layers thick, water films to 10 –5 mbar methane does not alter their morphology, suggestingmore » that the presence of the Pt(111) surface is not a strong driver for hydrate formation. This weak water–gas interaction at low pressures is supported by our thermal desorption measurements from amorphous solid water and crystalline ice where 1 ML of methane desorbs near ~ 43 K and isobutane desorbs near ~ 100 K. As a result, similar desorption temperatures were observed for desorption from amorphous solid water.« less

Thermochemical and kinetic analysis on the reactions of O2 with products from OH addition to isobutene, 2-hydroxy-1,1-dimethylethyl, and 2-hydroxy-2-methylpropyl radicals: HO2 formation from oxidation of neopentane, Part II.

PubMed

Sun, Hongyan; Bozzelli, Joseph W; Law, Chung K

2007-06-14

Unimolecular dissociation of a neopentyl radical to isobutene and methyl radical is competitive with the neopentyl association with O2 ((3)Sigma(g)-) in thermal oxidative systems. Furthermore, both isobutene and the OH radical are important primary products from the reactions of neopentyl with O2. Consequently, the reactions of O2 with the 2-hydroxy-1,1-dimethylethyl and 2-hydroxy-2-methylpropyl radicals resulting from the OH addition to isobutene are important to understanding the oxidation of neopentane and other branched hydrocarbons. Reactions that correspond to the association of radical adducts with O2((3)Sigma(g)-) involve chemically activated peroxy intermediates, which can isomerize and react to form one of several products before stabilization. The above reaction systems were analyzed with ab initio and density functional calculations to evaluate the thermochemistry, reaction paths, and kinetics that are important in neopentyl radical oxidation. The stationary points of potential energy surfaces were analyzed based on the enthalpies calculated at the CBS-Q level. The entropies, S(degrees)298, and heat capacities, C(p)(T), (0

Mechanism studies of the conversion of 13C-labeled n-butane on zeolite H-ZSM-5 by using 13C magic angle spinning NMR spectroscopy and GC-MS analysis.

PubMed

Luzgin, Mikhail V; Stepanov, Alexander G; Arzumanov, Sergei S; Rogov, Vladimir A; Parmon, Valentin N; Wang, Wei; Hunger, Michael; Freude, Dieter

2005-12-23

By using 13C MAS NMR spectroscopy (MAS = magic angle spinning), the conversion of selectively 13C-labeled n-butane on zeolite H-ZSM-5 at 430-470 K has been demonstrated to proceed through two pathways: 1) scrambling of the selective 13C-label in the n-butane molecule, and 2) oligomerization-cracking and conjunct polymerization. The latter processes (2) produce isobutane and propane simultaneously with alkyl-substituted cyclopentenyl cations and condensed aromatic compounds. In situ 13C MAS NMR and complementary ex situ GC-MS data provided evidence for a monomolecular mechanism of the 13C-label scrambling, whereas both isobutane and propane are formed through intermolecular pathways. According to 13C MAS NMR kinetic measurements, both pathways proceed with nearly the same activation energies (E(a) = 75 kJ mol(-1) for the scrambling and 71 kJ mol(-1) for isobutane and propane formation). This can be rationalized by considering the intermolecular hydride transfer between a primarily initiated carbenium ion and n-butane as being the rate-determining stage of the n-butane conversion on zeolite H-ZSM-5.

Synthesis and Mass Spectra of Butenyltin Compounds

DTIC Science & Technology

1989-03-01

activities or operations. One instance of this concern has focused on the Navy’s use of tributyltin compounds as antifoulants on ships’ hulls. Such...butene, and 1-chloro- 2-butene were obtained from Pfaltz & Bauer (Waterbury, CT). Resublimed magne- sium chips, tetrabutyltin and tributyltin bromide...preferential elimination of R minus R to form RSn ’from R3Sn + The fragmentation patterns of tributyltin bromide and tributenyltin bromides are dominated

Biofuel and chemical production by recombinant microorganisms via fermentation of proteinaceous biomass

DOEpatents

Liao, James C.; Cho, Kwang Myung; Yan, Yajun; Huo, Yixin

2016-03-15

Provided herein are metabolically modified microorganisms characterized by having an increased keto-acid flux when compared with the wild-type organism and comprising at least one polynucleotide encoding an enzyme that when expressed results in the production of a greater quantity of a chemical product when compared with the wild-type organism. The recombinant microorganisms are useful for producing a large number of chemical compositions from various nitrogen containing biomass compositions and other carbon sources. More specifically, provided herein are methods of producing alcohols, acetaldehyde, acetate, isobutyraldehyde, isobutyric acid, n-butyraldehyde, n-butyric acid, 2-methyl-1-butyraldehyde, 2-methyl-1-butyric acid, 3-methyl-1-butyraldehyde, 3-methyl-1-butyric acid, ammonia, ammonium, amino acids, 2,3-butanediol, 1,4-butanediol, 2-methyl-1,4-butanediol, 2-methyl-1,4-butanediamine, isobutene, itaconate, acetoin, acetone, isobutene, 1,5-diaminopentane, L-lactic acid, D-lactic acid, shikimic acid, mevalonate, polyhydroxybutyrate (PHB), isoprenoids, fatty acids, homoalanine, 4-aminobutyric acid (GABA), succinic acid, malic acid, citric acid, adipic acid, p-hydroxy-cinnamic acid, tetrahydrofuran, 3-methyl-tetrahydrofuran, gamma-butyrolactone, pyrrolidinone, n-methylpyrrolidone, aspartic acid, lysine, cadeverine, 2-ketoadipic acid, and/or S-adenosyl-methionine (SAM) from a suitable nitrogen rich biomass.

Replacing precious metals with carbide catalysts for hydrogenation reactions

DOE PAGES

Ruijun, Hou; Chen, Jingguang G.; Chang, Kuan; ...

2015-03-03

Molybdenum carbide (Mo₂C and Ni/Mo₂C) catalysts were compared with Pd/SiO₂ for the hydrogenation of several diene molecules, 1,3- butadiene, 1,3- and 1,4-cyclohexadiene (CHD). Compared to Pd/SiO₂, Mo₂C showed similar hydrogenation rate for 1,3-butadiene and 1,3-CHD and even higher rate for 1,4-CHD, but with significant deactivation rate for 1,3-CHD hydrogenation. However, the hydrogenation activity of Mo₂C could be completely regenerated by H₂ treatment at 723 K for the three molecules. The Ni modified Mo₂C catalysts retained similar activity for 1,3-butadiene hydrogenation with significantly enhanced selectivity for 1-butene production. The 1-butene selectivity increased with increasing Ni loading below 15%. Among the Nimore » modified Mo₂C catalysts, 8.6%Ni/Mo₂C showed the highest selectivity to 1-butene, which was even higher selectivity than that over Pd/SiO₂. Compared to Pd/SiO₂, both Mo₂C and Ni/Mo₂C showed combined advantages in hydrogenation activity and catalyst cost reduction, demonstrating the potential to use less expensive carbide catalysts to replace precious metals for hydrogenation reactions.« less

Characteristics of volatile organic compounds (VOCs) emitted from a petroleum refinery in Beijing, China

NASA Astrophysics Data System (ADS)

Wei, Wei; Cheng, Shuiyuan; Li, Guohao; Wang, Gang; Wang, Haiyan

2014-06-01

This study made a field VOCs (volatile organic compounds) measurement for a petroleum refinery in Beijing by determining 56 PAMS VOCs, which are demanded for photochemical assessment in US, and obtained the characteristics of VOCs emitted from the whole refinery and from its inner main devices. During the monitoring period, this refinery brought about an average increase of 61 ppbv in the ambient TVOCs (sum of the PAMS VOCs) at the refinery surrounding area, while the background of TVOCs there was only 10-30 ppbv. In chemical profile, the VOCs emitted from the whole refinery was characteristic by isobutane (8.7%), n-butane (7.9%), isopentane (6.3%), n-pentane (4.9%%), n-hexane (7.6%), C6 branched alkanes (6.0%), propene (12.7%), 1-butene (4.1%), benzene (7.8%), and toluene (5.9%). On the other hand, the measurement for the inner 5 devices, catalytic cracking units (CCU2 and CCU3), catalytic reforming unit (CRU), tank farm (TF), and wastewater treatment(WT), revealed the higher level of VOCs pollutions (about several hundred ppbv of TVOCs), and the individual differences in VOCs chemical profiles. Based on the measured speciated VOCs data at the surrounding downwind area, PMF receptor model was applied to identify the VOCs sources in the refinery. Then, coupling with the VOCs chemical profiles measured at the device areas, we concluded that CCU1/3 contributes to 25.9% of the TVOCs at the surrounding downwind area by volume, followed by CCU2 (24.7%), CRU (18.9%), TF (18.3%) and WT (12.0%), which was accordant with the research of US EPA (2008). Finally, ozone formation potentials of the 5 devices were also calculated by MIR technique, which showed that catalytic cracking units, accounting for about 55.6% to photochemical ozone formation, should be given the consideration of VOCs control firstly.

Sources of C₂-C₄ alkenes, the most important ozone nonmethane hydrocarbon precursors in the Pearl River Delta region.

PubMed

Zhang, Yanli; Wang, Xinming; Zhang, Zhou; Lü, Sujun; Huang, Zhonghui; Li, Longfeng

2015-01-01

Surface ozone is becoming an increasing concern in China's megacities such as the urban centers located in the highly industrialized and densely populated Pearl River Delta (PRD) region, where previous studies suggested that ozone production is sensitive to VOC emissions with alkenes being important precursors. However, little was known about sources of alkenes. Here we present our monitoring of ambient volatile organic compounds at four representative urban, suburban and rural sites in the PRD region during November-December 2009, which experienced frequent ozone episodes. C2-C4 alkenes, whose total mixing ratios were 11-20% of non-methane hydrocarbons (NMHCs) quantified, accounted for 38-64% of ozone formation potentials (OFPs) and 30-50% of the total hydroxyl radical (OH) reactivity by NMHCs. Ethylene was the most abundant alkene, accounting for 8-15% in total mixing ratios of NMHCs and contributed 25-46% of OFPs. Correlations between C2-C4 alkenes and typical source tracers suggested that ethylene might be largely related to vehicle exhausts and industry activities, while propene and butenes were much more LPG-related. Positive Matrix Factorization (PMF) confirmed that vehicle exhaust and liquefied petroleum gas (LPG) were two major sources that altogether accounted for 52-62%, 58-77%, 73-83%, 68-79% and 73-84% for ethylene, propene, 1-butene, trans-2-butene and cis-2-butene, respectively. Vehicle exhausts alone contributed 32-49% ethylene and 35-41% propene. Industry activities contributed 13-23% ethylene and 7-20% propene. LPG instead contributed the most to butenes (38-65%) and substantially to propene (23-36%). Extensive tests confirmed high fractions of propene and butenes in LPG then used in Guangzhou and in LPG combustion plumes; therefore, limiting alkene contents in LPG would benefit regional ozone control. Copyright © 2014 Elsevier B.V. All rights reserved.

Metal catalyzed synthesis of hyperbranched ethylene and/or .alpha.-olefin polymers

DOEpatents

Sen, Ayusman; Kim, Jang Sub; Pawlow, James H.; Murtuza, Shahid; Kacker, Smita; Wojcinski, III, Louis M.

2001-01-01

Oily hyperbranched polymers derived from ethylene, propylene, butene and/or a C.sub.5 -C.sub.24 .alpha.-olefin, and a method for their synthesis, are disclosed. The polymers have non-regular microstructures and are characterized by a ratio ({character pullout})of methyl hydrogens centered around 0.85 ppm on the 1H-NMR spectra of the polymers relative to total aliphatic hydrogens of from about 0.40 to about 0.65 for polymers derived from ethylene or butene, and a ratio ({character pullout})of from greater than 0.50 to about 0.65 for polymers derived from propylene. A method for grafting hyperbranched polymers derived from ethylene, propylene, butene and/or a C.sub.5 -C.sub.24 .alpha.-olefin onto aromatic rings in organic molecules and polymers, and the resulting grafted materials, are also disclosed. The hyperbranched polymers and grafted materials are useful, for example, as lubricants and lubricant additives.

Solid-state molecular organometallic chemistry. Single-crystal to single-crystal reactivity and catalysis with light hydrocarbon substrates.

PubMed

Chadwick, F Mark; McKay, Alasdair I; Martinez-Martinez, Antonio J; Rees, Nicholas H; Krämer, Tobias; Macgregor, Stuart A; Weller, Andrew S

2017-08-01

Single-crystal to single-crystal solid/gas reactivity and catalysis starting from the precursor sigma-alkane complex [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(η 2 η 2 -NBA)][BAr F 4 ] (NBA = norbornane; Ar F = 3,5-(CF 3 ) 2 C 6 H 3 ) is reported. By adding ethene, propene and 1-butene to this precursor in solid/gas reactions the resulting alkene complexes [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(alkene) x ][BAr F 4 ] are formed. The ethene ( x = 2) complex, [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(ethene) 2 ][BAr F 4 ]-Oct , has been characterized in the solid-state (single-crystal X-ray diffraction) and by solution and solid-state NMR spectroscopy. Rapid, low temperature recrystallization using solution methods results in a different crystalline modification, [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(ethene) 2 ][BAr F 4 ]-Hex , that has a hexagonal microporous structure ( P 6 3 22). The propene complex ( x = 1) [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(propene)][BAr F 4 ] is characterized as having a π-bound alkene with a supporting γ-agostic Rh···H 3 C interaction at low temperature by single-crystal X-ray diffraction, variable temperature solution and solid-state NMR spectroscopy, as well as periodic density functional theory (DFT) calculations. A fluxional process occurs in both the solid-state and solution that is proposed to proceed via a tautomeric allyl-hydride. Gas/solid catalytic isomerization of d 3 -propene, H 2 C 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 1111111111111111111111111111111111 1111111111111111111111111111111111 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 1111111111111111111111111111111111 1111111111111111111111111111111111 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 CHCD 3 , using [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(η 2 η 2 -NBA)][BAr F 4 ] scrambles the D-label into all possible positions of the propene, as shown by isotopic perturbation of equilibrium measurements for the agostic interaction. Periodic DFT calculations show a low barrier to H/D exchange (10.9 kcal mol -1 , PBE-D3 level), and GIPAW chemical shift calculations guide the assignment of the experimental data. When synthesized using solution routes a bis-propene complex, [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(propene) 2 ][BAr F 4 ] , is formed. [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(butene)][BAr F 4 ] ( x = 1) is characterized as having 2-butene bound as the cis -isomer and a single Rh···H 3 C agostic interaction. In the solid-state two low-energy fluxional processes are proposed. The first is a simple libration of the 2-butene that exchanges the agostic interaction, and the second is a butene isomerization process that proceeds via an allyl-hydride intermediate with a low computed barrier of 14.5 kcal mol -1 . [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(η 2 η 2 -NBA)][BAr F 4 ] and the polymorphs of [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(ethene) 2 ][BAr F 4 ] are shown to be effective in solid-state molecular organometallic catalysis (SMOM-Cat) for the isomerization of 1-butene to a mixture of cis - and trans -2-butene at 298 K and 1 atm, and studies suggest that catalysis is likely dominated by surface-active species. [Rh(Cy 2 PCH 2 CH 2 PCy 2 )(η 2 η 2 -NBA)][BAr F 4 ] is also shown to catalyze the transfer dehydrogenation of butane to 2-butene at 298 K using ethene as the sacrificial acceptor.

Ultrafast non-adiabatic dynamics of methyl substituted ethylenes: the π3s Rydberg state.

PubMed

Wu, Guorong; Boguslavskiy, Andrey E; Schalk, Oliver; Schuurman, Michael S; Stolow, Albert

2011-10-28

Excited state unimolecular reactions of some polyenes exhibit localization of their dynamics at a single ethylenic double bond. Here we present studies of the fundamental photophysical processes in the ethylene unit itself. Combined femtosecond time-resolved photoelectron spectroscopy (TRPES) and ab initio quantum chemical calculations was applied to the study of excited state dynamics in cis-butene, trans-butene, trimethylethylene, and tetramethylethylene, following initial excitation to their respective π3s Rydberg states. The wavelength dependence of the π3s Rydberg state dynamics of tetramethylethylene was investigated in more detail. The π3s Rydberg to ππ(∗) valence state decay rate varies greatly with substituent: the 1,2-di- and tri-methyl substituted ethylenes (cis-butene, trans-butene, and trimethylethylene) show an ultrafast decay (∼20 fs), whereas the fully methylated tetramethylethylene shows a decay rate of 2 to 4 orders of magnitude slower. These observations are rationalized in terms of topographical trends in the relevant potential energy surfaces, as found from ab initio calculations: (1) the barrier between the π3s state and the ππ∗ state increases with increasing methylation, and (2) the π3s∕ππ∗ minimum energy conical intersection displaces monotonically away from the π3s Franck-Condon region with increasing methylation. The use of systematic methylation in combination with TRPES and ab initio computation is emerging as an important tool in discerning the excited state dynamics of unsaturated hydrocarbons.

Ethene, propene, butene and isoprene emissions from a ponderosa pine forest measured by relaxed eddy accumulation

NASA Astrophysics Data System (ADS)

Rhew, Robert C.; Deventer, Malte Julian; Turnipseed, Andrew A.; Warneke, Carsten; Ortega, John; Shen, Steve; Martinez, Luis; Koss, Abigail; Lerner, Brian M.; Gilman, Jessica B.; Smith, James N.; Guenther, Alex B.; de Gouw, Joost A.

2017-11-01

Alkenes are reactive hydrocarbons that influence local and regional atmospheric chemistry by playing important roles in the photochemical production of tropospheric ozone and in the formation of secondary organic aerosols. The simplest alkene, ethene (ethylene), is a major plant hormone and ripening agent for agricultural commodities. The group of light alkenes (C2-C4) originates from both biogenic and anthropogenic sources, but their biogenic sources are poorly characterized, with limited field-based flux observations. Here we report net ecosystem fluxes of light alkenes and isoprene from a semiarid ponderosa pine forest in the Rocky Mountains of Colorado, USA using the relaxed eddy accumulation (REA) technique during the summer of 2014. Ethene, propene, butene and isoprene emissions have strong diurnal cycles, with median daytime fluxes of 123, 95, 39 and 17 µg m-2 h-1, respectively. The fluxes were correlated with each other, followed general ecosystem trends of CO2 and water vapor, and showed similar sunlight and temperature response curves as other biogenic VOCs. The May through October flux, based on measurements and modeling, averaged 62, 52, 24 and 18 µg m-2 h-1 for ethene, propene, butene and isoprene, respectively. The light alkenes contribute significantly to the overall biogenic source of reactive hydrocarbons: roughly 18 % of the dominant biogenic VOC, 2-methyl-3-buten-2-ol. The measured ecosystem scale fluxes are 40-80 % larger than estimates used for global emissions models for this type of ecosystem.

Ultrafast non-adiabatic dynamics of methyl substituted ethylenes: The π3s Rydberg state

NASA Astrophysics Data System (ADS)

Wu, Guorong; Boguslavskiy, Andrey E.; Schalk, Oliver; Schuurman, Michael S.; Stolow, Albert

2011-10-01

Excited state unimolecular reactions of some polyenes exhibit localization of their dynamics at a single ethylenic double bond. Here we present studies of the fundamental photophysical processes in the ethylene unit itself. Combined femtosecond time-resolved photoelectron spectroscopy (TRPES) and ab initio quantum chemical calculations was applied to the study of excited state dynamics in cis-butene, trans-butene, trimethylethylene, and tetramethylethylene, following initial excitation to their respective π3s Rydberg states. The wavelength dependence of the π3s Rydberg state dynamics of tetramethylethylene was investigated in more detail. The π3s Rydberg to ππ* valence state decay rate varies greatly with substituent: the 1,2-di- and tri-methyl substituted ethylenes (cis-butene, trans-butene, and trimethylethylene) show an ultrafast decay (˜20 fs), whereas the fully methylated tetramethylethylene shows a decay rate of 2 to 4 orders of magnitude slower. These observations are rationalized in terms of topographical trends in the relevant potential energy surfaces, as found from ab initio calculations: (1) the barrier between the π3s state and the ππ* state increases with increasing methylation, and (2) the π3s/ππ* minimum energy conical intersection displaces monotonically away from the π3s Franck-Condon region with increasing methylation. The use of systematic methylation in combination with TRPES and ab initio computation is emerging as an important tool in discerning the excited state dynamics of unsaturated hydrocarbons.

Photocatalytic oxidation mechanism of alkanes in contact with titanium dioxide

NASA Technical Reports Server (NTRS)

Formenti, M.; Juillet, F.; Teichner, S. J.

1977-01-01

Isobutane was photooxidized on titanium dioxide between -16 and +180 C in tertiary butanol and acetone. The formation of tertiary butanol preceded the formation of acetone. Above 20 C the latter compound became clearly predominant. The reaction kinetics obeyed a steady state model of oxygen chemisorption with the involvement of isobutane in the physisorbed phase.

Exploring low-temperature dehydrogenation at ionic Cu sites in beta zeolite to enable alkane recycle in dimethyl ether homologation

DOE PAGES

Farberow, Carrie A.; Cheah, Singfoong; Kim, Seonah; ...

2017-04-24

Cu-based catalysts containing targeted functionalities including metallic Cu, oxidized Cu, ionic Cu, and Bronsted acid sites were synthesized and evaluated for isobutane dehydrogenation. Hydrogen productivities, combined with operando X-ray absorption spectroscopy, indicated that Cu(I) sites in Cu/BEA catalysts activate C-H bonds in isobutane. Computational analysis revealed that isobutane dehydrogenation at a Cu(I) site proceeds through a two-step mechanism with a maximum energy barrier of 159 kJ/mol. Furthermore, these results demonstrate that light alkanes can be reactivated on Cu/BEA, which may enable re-entry of these species into the chain-growth cycle of dimethyl ether homologation, thereby increasing gasoline-range (C 5+) hydrocarbon yield.

Isotope effects and the temperature dependences of the hyperfine coupling constants of muoniated sec-butyl radicals in condensed phases.

PubMed

Fleming, Donald G; Bridges, Michael D; Arseneau, Donald J; Chen, Ya Kun; Wang, Yan Alexander

2011-04-07

Reported here is the first μSR study of the muon (A(μ)) and proton (A(p)) β-hyperfine coupling constants (Hfcc) of muoniated sec-butyl radicals, formed by muonium (Mu) addition to 1-butene and to cis- and trans-2-butene. The data are compared with in vacuo spin-unrestricted MP2 and hybrid DFT/B3YLP calculations reported in the previous paper (I), which played an important part in the interpretation of the data. The T-dependences of both the (reduced) muon, A(μ)′(T), and proton, A(p)(T), Hfcc are surprisingly well explained by a simple model, in which the calculated Hfcc from paper I at energy minima of 0 and near ±120° are thermally averaged, assuming an energy dependence given by a basic 2-fold torsional potential. Fitted torsional barriers to A(μ)′(T) from this model are similar (~3 kJ/mol) for all muoniated butyl radicals, suggesting that these are dominated by ZPE effects arising from the C−Mu bond, but for A(p)(T) exhibit wide variations depending on environment. For the cis- and trans-2-butyl radicals formed from 2-butene, A(μ)′(T) exhibits clear discontinuities at bulk butene melting points, evidence for molecular interactions enhancing these muon Hfcc in the environment of the solid state, similar to that found in earlier reports for muoniated tert-butyl. In contrast, for Mu−sec-butyl formed from 1-butene, there is no such discontinuity. The muon hfcc for the trans-2-butyl radical are seemingly very well predicted by B3LYP calculations in the solid phase, but for sec-butyl from 1-butene, showing the absence of further interactions, much better agreement is found with the MP2 calculations across the whole temperature range. Examples of large proton Hfcc near 0 K are also reported, due to eclipsed C−H bonds, in like manner to C−Mu, which then also exhibit clear discontinuities in A(p)(T) at bulk melting points. The data suggest that the good agreement found between theory and experiment from the B3LYP calculations for eclipsed bonds in the solid phase may be fortuitous. For the staggered protons of the sec-butyl radicals formed, no discontinuities are seen at all in A(p)(T), also demonstrating no further effects of molecular interactions on these particular proton Hfcc.

Formation of Alkenes via Degradation of tert-Alkyl Ethers and Alcohols by Aquincola tertiaricarbonis L108 and Methylibium spp. ▿†

PubMed Central

Schäfer, Franziska; Muzica, Liudmila; Schuster, Judith; Treuter, Naemi; Rosell, Mònica; Harms, Hauke; Müller, Roland H.; Rohwerder, Thore

2011-01-01

Bacterial degradation pathways of fuel oxygenates such as methyl tert-butyl and tert-amyl methyl ether (MTBE and TAME, respectively) have already been studied in some detail. However, many of the involved enzymes are still unknown, and possible side reactions have not yet been considered. In Aquincola tertiaricarbonis L108, Methylibium petroleiphilum PM1, and Methylibium sp. strain R8, we have now detected volatile hydrocarbons as by-products of the degradation of the tert-alkyl ether metabolites tert-butyl and tert-amyl alcohol (TBA and TAA, respectively). The alkene isobutene was formed only during TBA catabolism, while the beta and gamma isomers of isoamylene were produced only during TAA conversion. Both tert-alkyl alcohol degradation and alkene production were strictly oxygen dependent. However, the relative contribution of the dehydration reaction to total alcohol conversion increased with decreasing oxygen concentrations. In resting-cell experiments where the headspace oxygen content was adjusted to less than 2%, more than 50% of the TAA was converted to isoamylene. Isobutene formation from TBA was about 20-fold lower, reaching up to 4% alcohol turnover at low oxygen concentrations. It is likely that the putative tert-alkyl alcohol monooxygenase MdpJ, belonging to the Rieske nonheme mononuclear iron enzymes and found in all three strains tested, or an associated enzymatic step catalyzed the unusual elimination reaction. This was also supported by the detection of mdpJK genes in MTBE-degrading and isobutene-emitting enrichment cultures obtained from two treatment ponds operating at Leuna, Germany. The possible use of alkene formation as an easy-to-measure indicator of aerobic fuel oxygenate biodegradation in contaminated aquifers is discussed. PMID:21742915

Catalytic conversion of light alkanes. Final report, January 1, 1990--October 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

During the course of the first three years of the Cooperative Agreement (Phase I-III), we uncovered a family of metal perhaloporphyrin complexes which had unprecedented activity for the selective air-oxidation of fight alkanes to alcohols. The reactivity of fight hydrocarbon substrates with air or oxygen was in the order: isobutane>propane>ethane>methane, in accord with their homolytic bond dissociation energies. Isobutane was so reactive that the proof-of concept stage of a process for producing tert-butyl alcohol from isobutane was begun (Phase V). It was proposed that as more active catalytic systems were developed (Phases IV, VI), propane, then ethane and finally methanemore » oxidations will move into this stage (Phases VII through IX). As of this writing, however, the program has been terminated during the later stages of Phases V and VI so that further work is not anticipated. We made excellent progress during 1994 in generating a class of less costly new materials which have the potential for high catalytic activity. New routes were developed for replacing costly perfluorophenyl groups in the meso-position of metalloporphyrin catalysts with far less expensive and lower molecular weight perfluoromethyl groups.« less

Double addition of diethylamine to biacetylene (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trofimov, B.A.; Vavilova, A.N.

1986-03-01

Biacetylene reacts with an excess of diethylamine in dilute solutions of anhydrous acetonitrile, methanol, ethanol, and THF to form the diadduct 1,3-bis(diethyl-amino)-1,3-butadiene (lambda/sub max/ 325 nm). During concentration of the reaction mixture the latter undergoes hydration by the residual amounts of water in the 3-(diethylamino)-2-butenal. The spectral characteristics (UV, IR, PMR) of the intermediate reaction products are given. The kinetics of the stage of addition of the diethylamine and water to the monoadduct, 1-(diethylamino)-1-buten-3-yne, were studied. It was concluded that the addition of the nucleophile to the triple bond during its secondary amination and hydration is facilitated by the concertedmore » transfer of a proton.« less

Estimation of lower flammability limits of C-H compounds in air at atmospheric pressure, evaluation of temperature dependence and diluent effect.

PubMed

Mendiburu, Andrés Z; de Carvalho, João A; Coronado, Christian R

2015-03-21

Estimation of the lower flammability limits of C-H compounds at 25 °C and 1 atm; at moderate temperatures and in presence of diluent was the objective of this study. A set of 120 C-H compounds was divided into a correlation set and a prediction set of 60 compounds each. The absolute average relative error for the total set was 7.89%; for the correlation set, it was 6.09%; and for the prediction set it was 9.68%. However, it was shown that by considering different sources of experimental data the values were reduced to 6.5% for the prediction set and to 6.29% for the total set. The method showed consistency with Le Chatelier's law for binary mixtures of C-H compounds. When tested for a temperature range from 5 °C to 100 °C, the absolute average relative errors were 2.41% for methane; 4.78% for propane; 0.29% for iso-butane and 3.86% for propylene. When nitrogen was added, the absolute average relative errors were 2.48% for methane; 5.13% for propane; 0.11% for iso-butane and 0.15% for propylene. When carbon dioxide was added, the absolute relative errors were 1.80% for methane; 5.38% for propane; 0.86% for iso-butane and 1.06% for propylene. Copyright © 2014 Elsevier B.V. All rights reserved.

Unimolecular dissociation of protonated trans-1,4-diphenyl-2-butene-1,4-dione in the gas phase: rearrangement versus simple cleavage.

PubMed

Wu, Lianming; Liu, David Q; Vogt, Frederick G

2006-01-01

Fragmentation mechanisms of trans-1,4-diphenyl-2-butene-1,4-dione were studied using a variety of mass spectrometric techniques. The major fragmentation pathways occur by various rearrangements by loss of H(2)O, CO, H(2)O and CO, and CO(2). The other fragmentation pathways via simple alpha cleavages were also observed but accounted for the minor dissociation channels in both a two-dimensional (2-D) linear ion trap and a quadrupole time-of-flight (Q-TOF) mass spectrometer. The elimination of CO(2) (rather than CH(3)CHO or C(3)H(8)), which was confirmed by an exact mass measurement using the Q-TOF instrument, represented a major fragmentation pathway in the 2-D linear ion trap mass spectrometer. However, the elimination of H(2)O and CO becomes more competitive in the beam-type Q-TOF instrument. The loss of CO is observed in both the MS(2) experiment of m/z 237 and the MS(3) experiment of m/z 219 but via the different transition states. The data suggest that the olefinic double bond in protonated trans-1,4-diphenyl-2-butene-1,4-dione plays a key role in stabilizing the rearrangement transition states and increasing the bond dissociation (cleavage) energy to give favorable rearrangement fragmentation pathways. Copyright (c) 2006 John Wiley & Sons, Ltd.

Solid-state molecular organometallic chemistry. Single-crystal to single-crystal reactivity and catalysis with light hydrocarbon substrates† †Electronic supplementary information (ESI) available: Full details of experimental details, spectroscopic and other analytical data, X-ray crystallography, catalytic conditions, and computational studies. CCDC 1539832–1539836. For ESI and crystallographic data in CIF or other electronic format see DOI: 10.1039/c7sc01491k

PubMed Central

Chadwick, F. Mark; McKay, Alasdair I.; Martinez-Martinez, Antonio J.; Rees, Nicholas H.; Krämer, Tobias

2017-01-01

Single-crystal to single-crystal solid/gas reactivity and catalysis starting from the precursor sigma-alkane complex [Rh(Cy2PCH2CH2PCy2)(η2η2-NBA)][BArF4] (NBA = norbornane; ArF = 3,5-(CF3)2C6H3) is reported. By adding ethene, propene and 1-butene to this precursor in solid/gas reactions the resulting alkene complexes [Rh(Cy2PCH2CH2PCy2)(alkene)x][BArF4] are formed. The ethene (x = 2) complex, [Rh(Cy2PCH2CH2PCy2)(ethene)2][BArF4]-Oct, has been characterized in the solid-state (single-crystal X-ray diffraction) and by solution and solid-state NMR spectroscopy. Rapid, low temperature recrystallization using solution methods results in a different crystalline modification, [Rh(Cy2PCH2CH2PCy2)(ethene)2][BArF4]-Hex, that has a hexagonal microporous structure (P6322). The propene complex (x = 1) [Rh(Cy2PCH2CH2PCy2)(propene)][BArF4] is characterized as having a π-bound alkene with a supporting γ-agostic Rh···H3C interaction at low temperature by single-crystal X-ray diffraction, variable temperature solution and solid-state NMR spectroscopy, as well as periodic density functional theory (DFT) calculations. A fluxional process occurs in both the solid-state and solution that is proposed to proceed via a tautomeric allyl-hydride. Gas/solid catalytic isomerization of d3-propene, H2C 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 1111111111111111111111111111111111 1111111111111111111111111111111111 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 1111111111111111111111111111111111 1111111111111111111111111111111111 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 0000000000000000000000000000000000 CHCD3, using [Rh(Cy2PCH2CH2PCy2)(η2η2-NBA)][BArF4] scrambles the D-label into all possible positions of the propene, as shown by isotopic perturbation of equilibrium measurements for the agostic interaction. Periodic DFT calculations show a low barrier to H/D exchange (10.9 kcal mol–1, PBE-D3 level), and GIPAW chemical shift calculations guide the assignment of the experimental data. When synthesized using solution routes a bis-propene complex, [Rh(Cy2PCH2CH2PCy2)(propene)2][BArF4], is formed. [Rh(Cy2PCH2CH2PCy2)(butene)][BArF4] (x = 1) is characterized as having 2-butene bound as the cis-isomer and a single Rh···H3C agostic interaction. In the solid-state two low-energy fluxional processes are proposed. The first is a simple libration of the 2-butene that exchanges the agostic interaction, and the second is a butene isomerization process that proceeds via an allyl-hydride intermediate with a low computed barrier of 14.5 kcal mol–1. [Rh(Cy2PCH2CH2PCy2)(η2η2-NBA)][BArF4] and the polymorphs of [Rh(Cy2PCH2CH2PCy2)(ethene)2][BArF4] are shown to be effective in solid-state molecular organometallic catalysis (SMOM-Cat) for the isomerization of 1-butene to a mixture of cis- and trans-2-butene at 298 K and 1 atm, and studies suggest that catalysis is likely dominated by surface-active species. [Rh(Cy2PCH2CH2PCy2)(η2η2-NBA)][BArF4] is also shown to catalyze the transfer dehydrogenation of butane to 2-butene at 298 K using ethene as the sacrificial acceptor. PMID:28989631

21 CFR 177.1430 - Isobutylene-butene copolymers.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) of this section. (b) Specifications: Isobutylene-butene copolymers Molecular weight (range) Viscosity...: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (2) Viscosity. Viscosity shall be determined by ASTM method D445-74, “Test for Kinematic Viscosity of Transparent and...

21 CFR 177.1430 - Isobutylene-butene copolymers.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) of this section. (b) Specifications: Isobutylene-butene copolymers Molecular weight (range) Viscosity...: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (2) Viscosity. Viscosity shall be determined by ASTM method D445-74, “Test for Kinematic Viscosity of Transparent and...

21 CFR 177.1430 - Isobutylene-butene copolymers.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) of this section. (b) Specifications: Isobutylene-butene copolymers Molecular weight (range) Viscosity...: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. (2) Viscosity. Viscosity shall be determined by ASTM method D445-74, “Test for Kinematic Viscosity of Transparent and...

Conversion of Syngas-Derived C2+ Mixed Oxygenates to C3-C5 Olefins over ZnxZryOz Mixed Oxides Catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Colin D.; Lebarbier, Vanessa M.; Flake, Matthew D.

2016-04-01

In this study we report on a ZnxZryOz mixed oxide type catalyst capable of converting a syngas-derived C2+ mixed oxygenate feedstock to isobutene-rich olefins. Aqueous model feed comprising of ethanol, acetaldehyde, acetic acid, ethyl acetate, methanol, and propanol was used as representative liquid product derived from a Rh-based mixed oxygenate synthesis catalyst. Greater than 50% carbon yield to C3-C5 mixed olefins was demonstrated when operating at 400-450oC and 1 atm. In order to rationalize formation of the products observed feed components were individually evaluated. Major constituents of the feed mixture (ethanol, acetaldehyde, acetic acid, and ethyl acetate) were found tomore » produce isobutene-rich olefins. C-C coupling was also demonstrated for propanol feedstock - a minor constituent of the mixed oxygenate feed - producing branched C6 olefins, revealing scalability to alcohols higher than ethanol following an analogous reaction pathway. Using ethanol and propanol feed mixtures, cross-coupling reactions produced mixtures of C4, C5, and C6 branched olefins. The presence of H2 in the feed was found to facilitate hydrogenation of the ketone intermediates, thus producing straight chain olefins as byproducts. While activity loss from coking is observed complete catalyst regeneration is achieved by employing mild oxidation. For conversion of the mixed oxygenate feed a Zr/Zn ratio of 2.5 and a reaction temperature of 450oC provides the best balance of stability, activity, and selectivity. X-ray diffraction and scanning transmission electron microscopy analysis reveals the presence of primarily cubic phase ZrO2 and a minor amount of the monoclinic phase, with ZnO being highly dispersed in the lattice. The presence of ZnO appears to stabilize the cubic phase resulting in less monoclinic phase as the ZnO concentration increases. Infrared spectroscopy shows the mixed oxide acid sites are characterized as primarily Lewis type acidity. The direct relationship between isobutene production and the ratio of basic/acidic sites was demonstrated. An optimized balance of active sites for isobutene production from acetone was obtained with a basic/acidic site ratio of ~2. This technology for the conversion of aqueous mixtures of C2+ mixed oxygenates provides significant advantages over other presently studied catalysts in that its unique properties permit the utilization of a variety of feeds in a consistently selective manner.« less

Sequential and direct ionic excitation in the strong-field ionization of 1-butene molecules.

PubMed

Schell, Felix; Boguslavskiy, Andrey E; Schulz, Claus Peter; Patchkovskii, Serguei; Vrakking, Marc J J; Stolow, Albert; Mikosch, Jochen

2018-05-18

We study the Strong-Field Ionization (SFI) of the hydrocarbon 1-butene as a function of wavelength using photoion-photoelectron covariance and coincidence spectroscopy. We observe a striking transition in the fragment-associated photoelectron spectra: from a single Above Threshold Ionization (ATI) progression for photon energies less than the cation D0-D1 gap to two ATI progressions for a photon energy greater than this gap. For the first case, electronically excited cations are created by SFI populating the ground cationic state D0, followed by sequential post-ionization excitation. For the second case, direct sub-cycle SFI to the D1 excited cation state contributes significantly. Our experiments access ionization dynamics in a regime where strong-field and resonance-enhanced processes can interplay.

Active-site-directed irreversible inhibitors of isopentenyl diphosphate isomerase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muhlbacher, M.

1987-01-01

Seven analogues of isopentenyl diphosphate, containing fluorine, epoxy, or ammonium functionalities were found to irreversibly inhibit isopentenyl diphosphate:dimethylallyl diphosphate isomerase isolated from the mold Claviceps purpurea. The mechanism of their inhibition of isomerase was studied. Syntheses of 3-(fluoromethyl)-3-buten-1-yl diphosphate, 2-dimethylamino-1-ethyl diphosphate, 3,4-epoxy-3-methyl-1-butyl diphosphate, 3,4,-epoxy-1-butyl diphosphate, and 2,3-epoxy-3-methyl-1-butyl diphosphate were developed and carried out in high overall yield affording 100 mg quantities of the triammonium diphosphate salts. Radiolabeled materials of these analogues with {sup 3}H, {sup 14}C, and {sup 32}P at appropriate positions were also prepared. Inactivation kinetics, substrate protection studies, and labeling experiments demonstrated that the analogues interact stoichiometrically withmore » the active-site of isomerase. Radioactive enzyme-inactivator complexes were isolated, that are stable to extended dialysis and chaotropic reagents. The complexes resulting from inactivation of the enzyme by 3-(fluoromethyl)-3-buten-1-yl diphosphate and 3,4-epoxy-3-methyl-1-butyl diphosphate are stable to ion exchange chromatography and gel electrophoresis. Stoichiometric fluoride ion release occurs during inactivation of isomerase with 3-(fluoromethyl)-3-buten-1-yl diphosphate. The complexes are not stable to high concentrations of mixtures of 2-mercaptoethanol-sodium dodecyl sulfate. The radiolabeled 2-dimethylamino-1-ethyl diphosphate isomerase complex loses radioactivity almost instantaneously when treated with base. Partial fragmentation of the inactivator molecule was observed.« less

The Low Temperature Oxidation of 2,7-Dimethyloctane in a Pressurized Flow Reactor

NASA Astrophysics Data System (ADS)

Farid, Farinaz

The complexity of real fuels has fostered the use of simple mixtures of hydrocarbons whose combustion behavior approximates that of real fuels in both experimental and computational studies to develop models of the combustion of the real fuel. These simple mixtures have been called surrogates. Lightly branched paraffins are an important class of constituents in gasoline, diesel and aviation turbine fuels and therefore are primary candidates for use as a component in a surrogate. Unfortunately, fundamental studies on combustion characteristics of high molecular weight mono- and di-methylated iso-paraffins are scarce. Therefore, this study was designed to investigate the low-temperature oxidation of 2,7-dimethyloctane (2,7-DMO) (C10H22), a lightly branched isomer of decane. Replicate 2,7-DMO oxidation experiments were conducted in a pressurized flow reactor (PFR) over the temperature range of 550 -- 850 K, at a pressure of 8 atm and an equivalence ratio of 0.3 in 4.21% oxygen / nitrogen. The reactivity was mapped by continuous monitoring of CO, CO 2, and O2 using a non-dispersive infrared (NDIR) carbon monoxide / carbon dioxide analyzer and an electrochemical oxygen sensor. For examining the underlying reaction chemistry, detailed speciation of samples was performed at selected temperatures using a gas chromatograph with a flame ionization detector coupled to a mass spectrometer. Comparable oxidation experiments for n-decane were carried out to examine the unique effects of branching on fuel reactivity and distribution of major stable intermediates. For both isomers, the onset of negative temperature coefficient (NTC) region was observed near 700 K, with the reactivity decreasing with increasing the temperature. The flow reactor study of n-decane oxidation confirmed that the isomerization reduces the amount of CO produced at peak reactivity. In addition to reaction inhibition, branching affected the distribution of C2-C 4 olefin intermediates. While the oxidation of n-decane resulted primarily in the formation of ethene near the NTC start, propene and isobutene were the major olefins produced from 2,7-DMO. A comparative analysis of experimental data with respect to a detailed chemical kinetic model for 2,7-DMO was performed and discrepancies were noted. Based on these results, a collaborative effort with Dr. Charles Westbrook (Lawrence Livermore National Laboratory) was initiated to refine the model predictions in the low temperature and NTC regimes. The effort resulted in an updated version of the 2,7-DMO mechanism, improving some of the key features such as calculated CO2 profile and final yields of iso-butene over the studied range of temperature. Fuel pyrolysis in the intermediate temperature regime, 850 -- 1000 K, also was investigated for the first time in the PFR facility. However, preliminary n-decane experiments measured only a small amount of fuel decomposition, indicating that higher temperature operation would be beneficial. The major species produced from n-decane decomposition, in descending order of molar fraction, were ethene, propene, and 1-butene. These results were compared with the predictions of two existing chemical kinetic models and the sources of variations between the experiments and the models as well as among the mechanisms were investigated. At 1000 K, the mechanisms predicted higher levels of fuel depletion and ethene production. Also, while the mechanisms were similar in their predicted pathways for fuel depletion and formation of ethene, inconsistencies were observed in relative contribution of these pathways to the final yields as well as the rate parameter determination for several sensitive reactions with respect to n-decane and ethene. Overall, the research aided in achieving a data set quantifying the oxidation characteristics of 2,7-DMO (and n-decane for comparison) as well as an elucidation of critical reaction pathways based on experimental results. Preliminary pyrolysis experiments were carried out using n-decane and the limitations on companion 2,7-DMO pyrolysis experiments were established. The data was compared with the predictions of several chemical kinetic mechanisms and, using tools such as rate of production analysis and sensitivity analysis, the sources of deviations from experimental data as well as possible areas of improvement were identified. The findings from 2,7-DMO study was directly used to refine an existing chemical kinetic model for 2,7-DMO, in line with the ultimate goal of feeding the much needed experimental database for validation and refinement of kinetic models of jet fuel surrogates.

Fourier-transform i.r. gas chromatography—mass spectrometry study of varying light olefin reactivity on dealuminated ZSM-5

NASA Astrophysics Data System (ADS)

Sayed, Moein B.

Olefin oligomerization and alkylation (by methanol) of ethene, propene, and isobutene on HZSM-5 have been studied in typical conditions of the catalytic Mobil methanol to gasoline (MTG) process. This has been to identify the most likely light olefin involved as a key intermediate and the most likely mechanism by which such a light olefin propagates to gasoline in the MTG process. Reactions involving bulky intermediates are restricted within the narrow channels of ZSM-5. The oligomerization of ethene and isobutene appears to be an example of such restricted reactions. Zeolite dealumination seems to assist in overcoming the steric barrier by increasing both the zeolite pore volume and the population of the site (silanol) hosting the adsorbate. Spectral i.r. evidence reveals a role of zeolite Lewis acidity as a precursor in initiating olefin protonation by the zeolite Brønsted acidity. Both i.r. and GC—MS data consistently reveal a product distribution similar to that obtained in the MTG process, which suggests a dominant oligomerization and/or alkylation to be the mechanism leading to gasoline in the MTG process. However, the higher reactivity detected for olefin alkylation indicates alkylation to be the favoured mechanism. Propene is more likely to be a key intermediate, whereas isobutene contributes with a role being increasingly dominant over the more dealuminated ZSM-5 surfaces. Ethene, in contrast, shows poor reactivity, which can be enhanced by the zeolite dealumination.

Forensic medical evaluation of deaths resulting from inhalation of cigarette lighter refill fuel in Turkey.

PubMed

Özdemir, Erdinç; Eş, Hüseyin; Demir, Muhammet; Üzün, İbrahim

2017-01-01

Voluntary inhalation/abuse of volatile substances is an important public health problem which especially affects adolescent and young populations worldwide and may be encountered in all socioeconomic and cultural levels. Lighter gas abuse-related death is still an important health problem in Turkey. In this study, 25,265 case files and final reports submitted to the Institute of Forensic Medicine of the First Specialization Board between January 2011 and December 2015 were evaluated retrospectively. In 56 of these cases, lighter gas inhalation (n-butane, propane, isobutane) was recorded as the cause of death. All subjects were male with a mean age of 16.8years. According to eyewitness and crime scene investigation reports, in 48 (85.7%) of the cases, a lighter refill container was found at the scene. It was determined that 21.4% of the cases used a plastic bag to increase the effects of lighter gas and 76.8% inhaled the lighter gas via their mouth and nose. The toxicological analysis of the samples taken while hospitalized showed no lighter refill components (n-butane, propane, isobutane) in 66% of the cases, n-butane in 32.1% of the cases, and n-butane+propane+isobutane in 1.9% of the cases. The importance of lighter gas inhalation-related deaths in Turkey has been increasing. Strict measures against the abuse of these very dangerous substances should be undertaken by the mutual efforts of medical specialists and legislators. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Variation in the thermionic work function of semiconductor powders exposed to electromagnetic radiation

NASA Technical Reports Server (NTRS)

Bourasseau, S.; Martin, J. R.; Juillet, F.; Teichner, S. J.

1977-01-01

The study of the variation of thermoelectronic work function potential of TiO2 in the presence of isobutane shows that this gas is not adsorbed on this solid, in either the presence or the absence of ultraviolet radiation. These results, as well as those obtained in a previous work, lead to the mechanism of the photo-oxidation of isobutane at room temperature, in which excited atomic oxygen is the active species.

Reactions of butadiyne. 1: The reaction with hydrogen atoms

NASA Technical Reports Server (NTRS)

Schwanebeck, W.; Warnatz, J.

1984-01-01

The reaction of hydrogen (H) atoms with butadiene (C4H2) was studied at room temperature in a pressure range between w mbar and 10 mbar. The primary step was an addition of H to C4H2 which is in its high pressure range at p 1 mbar. Under these conditions the following addition of a second H atom lies in the transition region between low and high pressure range. Vibrationally excited C4H4 can be deactivated to form buten-(1)-yne-(3)(C4H4) or decomposes into two C2H2 molecules. The rate constant at room temperature for primary step is given. The second order rate constant for the consumption of buten-(1)-yne-(3) is an H atom excess at room temperature is given.

Volatile organic compound adsorption in a gas-solid fluidized bed.

PubMed

Ng, Y L; Yan, R; Tsen, L T S; Yong, L C; Liu, M; Liang, D T

2004-01-01

Fluidization finds many process applications in the areas of catalytic reactions, drying, coating, combustion, gasification and microbial culturing. This work aims to compare the dynamic adsorption characteristics and adsorption rates in a bubbling fluidized bed and a fixed bed at the same gas flow-rate, gas residence time and bed height. Adsorption with 520 ppm methanol and 489 ppm isobutane by the ZSM-5 zeolite of different particle size in the two beds enabled the differentiation of the adsorption characteristics and rates due to bed type, intraparticle mass transfer and adsorbate-adsorbent interaction. Adsorption of isobutane by the more commonly used activated carbon provided the comparison of adsorption between the two adsorbent types. With the same gas residence time of 0.79 seconds in both the bubbling bed and fixed bed of the same bed size of 40 mm diameter and 48 mm height, the experimental results showed a higher rate of adsorption in the bubbling bed as compared to the fixed bed. Intraparticle mass transfer and adsorbent-adsorbate interaction played significant roles in affecting the rate of adsorption, with intraparticle mass transfer being more dominant. The bubbling bed was observed to have a steeper decline in adsorption rate with respect to increasing outlet concentration compared to the fixed bed. The adsorption capacities of zeolite for the adsorbates studied were comparatively similar in both beds; fluidizing, and using smaller particles in the bubbling bed did not increase the adsorption capacity of the ZSM-5 zeolite. The adsorption capacity of activated carbon for isobutane was much higher than the ZSM-5 zeolite for isobutane, although at a lower adsorption rate. Fourier transform infra-red (FTIR) spectroscopy was used as an analytical tool for the quantification of gas concentration. Calibration was done using a series of standards prepared by in situ dilution with nitrogen gas, based on the ideal gas law and relating partial pressure to gas concentration. Concentrations up to 220 ppm for methanol and 75 ppm for isobutane were prepared using this method.

Electron collisions with methyl-substituted ethylenes: Cross section measurements and calculations for 2-methyl–2-butene and 2,3-dimethyl–2-butene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szmytkowski, Czesław, E-mail: czsz@mif.pg.gda.pl; Stefanowska, Sylwia; Zawadzki, Mateusz

We report electron-scattering cross sections determined for 2-methyl–2-butene [(H{sub 3}C)HC = C(CH{sub 3}){sub 2}] and 2,3-dimethyl–2-butene [(H{sub 3}C){sub 2}C = C(CH{sub 3}){sub 2}] molecules. Absolute grand-total cross sections (TCSs) were measured for incident electron energies in the 0.5–300 eV range, using a linear electron-transmission technique. The experimental TCS energy dependences for the both targets appear to be very similar with respect to the shape. In each TCS curve, three features are discernible: the resonant-like structure located around 2.6–2.7 eV, the broad distinct enhancement peaking near 8.5 eV, and a weak hump in the vicinity of 24 eV. Theoretical integral elasticmore » (ECS) and ionization (ICS) cross sections were computed up to 3 keV by means of the additivity rule (AR) approximation and the binary-encounter-Bethe method, respectively. Their sums, (ECS+ICS), are in a reasonable agreement with the respective measured TCSs. To examine the effect of methylation of hydrogen sides in the ethylene [H{sub 2}C = CH{sub 2}] molecule on the TCS, we compared the TCS energy curves for the sequence of methylated ethylenes: propene [H{sub 2}C = CH(CH{sub 3})], 2-methylpropene [H{sub 2}C = C(CH{sub 3}){sub 2}], 2-methyl–2-butene [(H{sub 3}C)HC = C(CH{sub 3}){sub 2}], and 2,3-dimethyl–2-butene [(H{sub 3}C){sub 2}C = C(CH{sub 3}){sub 2}], measured in the same laboratory. Moreover, the isomeric effect is also discussed for the C{sub 5}H{sub 10} and C{sub 6}H{sub 12} compounds.« less

Organosulfates as Tracers for Secondary Organic Aerosol (SOA) Formation from 2-Methyl-3-Buten-2 ol (MBO) in the Atmosphere

EPA Science Inventory

2-Methyl-3-buten-2-ol (MBO) is an important biogenic volatile organic compound (BVOC) emitted by pine trees and a potential precursor of atmospheric secondary organic aerosol (SOA) in forested regions. In the present study, hydroxyl radical (OH)-initiated oxidation of MBO was exa...

Biosynthesis of 2-methyl-3-buten-2-ol emitted from needles of Pinus ponderosa via the non-mevalonate DOXP/MEP pathway of isoprenoid formation.

PubMed

Zeidler, J; Lichtenthaler, H K

2001-06-01

The volatile hemiterpene 2-methyl-3-buten-2-ol (MBO) is emitted from the needles of several pine species from the Western United States and contributes to ozone formation in the atmosphere. It is synthesised enzymatically from dimethylallyl diphosphate (DMAPP). We show here that needles of Pinus ponderosa Laws. incorporated [1-2H1]-1-deoxy-D-xylulose (d-DOX) into the emitted MBO, but not D,L-[2-13C]mevalonic acid lactone. Furthermore, MBO emission was inhibited by fosmidomycin, a specific inhibitor of the second enzyme of the mevalonate-independent pathway of isopentenyl diphosphate and DMAPP formation, i.e. the 1-deoxy-D-xylulose 5-phosphate/2-C-methyl-D-erythritol 4-phosphate (DOXP/MEP) pathway. We thus prove that MBO emitted from needles of P. ponderosa is primarily formed via the DOXP/MEP pathway.

Microwave-Assisted Synthesis of a Natural Insecticide on Basic Montmorillonite K10 Clay. Green Chemistry in the Undergraduate Organic Laboratory

ERIC Educational Resources Information Center

Dintzner, Matthew R.; Wucka, Paul R.; Lyons, Thomas W.

2006-01-01

A detailed investigation of the clay-catalyzed condensation of sesamol and other phenols with 3-methyl-2-butenal to give methylenedioxyprecocene (MDP) and other chromenes is presented. The clay-catalyzed microwave-assisted condensation of sesamol with 3-methyl-2-butenal is appropriate for incorporation into undergraduate organic laboratory…

Chlorine atom-initiated low-temperature oxidation of prenol and isoprenol: The effect of C=C double bonds on the peroxy radical chemistry in alcohol oxidation

DOE PAGES

Welz, Oliver; Savee, John D.; Osborn, David L.; ...

2014-07-04

The chlorine atom-initiated oxidation of two unsaturated primary C5 alcohols, prenol (3-methyl-2-buten-1-ol, (CH 3) 2CCHCH 2OH) and isoprenol (3-methyl-3-buten-1-ol, CH 2C(CH 3)CH 2CH 2OH), is studied at 550 K and low pressure (8 Torr). The time- and isomer-resolved formation of products is probed with multiplexed photoionization mass spectrometry (MPIMS) using tunable vacuum ultraviolet ionizing synchrotron radiation. The peroxy radical chemistry of the unsaturated alcohols appears much less rich than that of saturated C4 and C5 alcohols. The main products observed are the corresponding unsaturated aldehydes – prenal (3-methyl-2-butenal) from prenol oxidation and isoprenal (3-methyl-3-butenal) from isoprenol oxidation. No significant productsmore » arising from QOOH chemistry are observed. These results can be qualitatively explained by the formation of resonance stabilized allylic radicals via H-abstraction in the Cl + prenol and Cl + isoprenol initiation reactions. The loss of resonance stabilization upon O 2 addition causes the energies of the intermediate wells, saddle points, and products to increase relative to the energy of the initial radicals and O 2. These energetic shifts make most product channels observed in the peroxy radical chemistry of saturated alcohols inaccessible for these unsaturated alcohols. The experimental findings are underpinned by quantum-chemical calculations for stationary points on the potential energy surfaces for the reactions of the initial radicals with O 2. Under our conditions, the dominant channels in prenol and isoprenol oxidation are the chain-terminating HO 2-forming channels arising from radicals, in which the unpaired electron and the –OH group are on the same carbon atom, with stable prenal and isoprenal co-products, respectively. These results suggest that the presence of C=C double bonds in alcohols will reduce low-temperature reactivity during autoignition.« less

SOA Formation from the Atmospheric Oxidation of 2-Methyl-3-Buten-2-ol and Its Implications for PM2.5

EPA Science Inventory

The formation of secondary organic aerosol (SOA) generated by irradiating 2-methyl-3-buten-2-01 (MBO) in the presence and/or absence of NO_x H₂O2, and/or SO₂ was examined. Experiments were conducted. in smog chambers operated either in dyna....

Determination of Tamoxifen and its Major Metabolites in Exposed Fish

EPA Science Inventory

Tamoxifen (TAM), (Z)-1-(p-dimethylaminoethoxyphenyl)-1, 2-diphenyl-1-butene, is a nonsteroidal agent that has been used in breast cancer treatment for decades. Its major metabolites are 4-hydroxytamoxifen (4-OHT), N-desmethyltamoxifen (DMT), and endoxifen. While TAM and metabolit...

Ice core records of monoterpene- and isoprene-SOA tracers from Aurora Peak in Alaska since 1660s: Implication for climate change variability in the North Pacific Rim

NASA Astrophysics Data System (ADS)

Pokhrel, Ambarish; Kawamura, Kimitaka; Ono, Kaori; Seki, Osamu; Fu, Pingqing; Matoba, Sumio; Shiraiwa, Takayuki

2016-04-01

Monoterpene and isoprene secondary organic aerosol (SOA) tracers are reported for the first time in an Alaskan ice core to better understand the biological source strength before and after the industrial revolution in the Northern Hemisphere. We found significantly high concentrations of monoterpene- and isoprene-SOA tracers (e.g., pinic, pinonic, and 2-methylglyceric acids, 2-methylthreitol and 2-methylerythritol) in the ice core, which show historical trends with good correlation to each other since 1660s. They show positive correlations with sugar compounds (e.g., mannitol, fructose, glucose, inositol and sucrose), and anti-correlations with α-dicarbonyls (glyoxal and methylglyoxal) and fatty acids (e.g., C18:1) in the same ice core. These results suggest similar sources and transport pathways for monoterpene- and isoprene-SOA tracers. In addition, we found that concentrations of C5-alkene triols (e.g., 3-methyl-2,3,4-trihydroxy-1-butene, cis-2-methyl 1,3,4-trihydroxy-1-butene and trans-2-methyl-1,3,4-trihydroxy-1-butene) in the ice core have increased after the Great Pacific Climate Shift (late 1970s). They show positive correlations with α-dicarbonyls and fatty acids (e.g., C18:1) in the ice core, suggesting that enhanced oceanic emissions of biogenic organic compounds through the marine boundary layer are recorded in the ice core from Alaska. Photochemical oxidation process for these monoterpene- and isoprene-/sesquiterpene-SOA tracers are suggested to be linked with the periodicity of multi-decadal climate oscillations and retreat of sea ice in the Northern Hemisphere.

21 CFR 177.1430 - Isobutylene-butene copolymers.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Maximum bromine value 1. Used as release agents in petroleum wax complying with § 178.3710 of this chapter... release coatings on backings or linings for pressure-sensitive adhesive labels complying with § 175.125 of...

[Research on the modification of Kevlar fiber by polypropylene glycol and cis-2-butene-1,4-diol].

PubMed

Zheng, Yu-ying; Wang, Can-yao; Fu, Ming-lian; Cai, Wei-long; Wang, Liang-en

2005-03-01

The mechanism of the modification of Kevlar fiber by polypropylene glycol(PPG) and cis-2-butene-1, 4-diol was studied in the paper, the authors learned the esterification of toluene-2, 4-diisocyanate (TDI) onto Kevlar fiber by infrared spectrum. In the mean time, the infrared spectrograms of the productions which steadily disposed by PPG and butendiol were analysed respectively, the result showed that the intensity of the bands was reinforced at about 1700-1720 cm(-1) after the samples were steadily disposed, that is to say, the group of --NCO has been stabilized into --NHCO group, the effect of steady disposal was obvious; but the disposal effect of butendiol was apparently better than PPG's at the same condition. Finally, the authors compared the influence of different mol rates between TDI and butendiol on the productions. Based onthe consequence, excessive butendiol would prevent the Kevlar fiber from farther reaction, therefore, the mol rate between TDI and butendiol should approach 1:1.

21 CFR 184.1165 - n-Butane and iso-butane.

Code of Federal Regulations, 2014 CFR

2014-04-01

.... Nos. 106-97-8 and 75-28-5, respectively) are colorless, flammable gases at normal temperatures and..., adsorption to surface-active agents, or refrigeration. (b) The ingredients must be of a purity suitable for... manufacturing practice conditions of use: (1) The ingredients are used as propellants, aerating agents, and...

40 CFR 98.406 - Data reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.406 Data..., isobutane, and pentanes plus. (3) Annual volumes in Mscf of natural gas received for processing. (4) Annual... report for each LDC shall contain the following information. (1) Annual volume in Mscf of natural gas...

40 CFR 98.406 - Data reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.406 Data..., isobutane, and pentanes plus. (3) Annual volumes in Mscf of natural gas received for processing. (4) Annual... shall contain the following information. (1) Annual volume in Mscf of natural gas received by the LDC at...

Transport of hop aroma compounds across Caco-2 monolayers.

PubMed

Heinlein, A; Metzger, M; Walles, H; Buettner, A

2014-11-01

Although being reported and used as a sedative remedy for several years, the bioactive principle of hop preparations is still not decisively clarified. Understanding absorption and transformation processes of potential physiologically active constituents is essential to evaluate the likeliness of biological effects on humans. Therefore, single hop aroma compounds as well as digestive transformation products thereof have been investigated in view of their human intestinal absorption, applying Caco-2 transport experiments as well as investigations on potential biotransformation processes. Selective and sensitive identification and quantification were thereby achieved by application of two-dimensional high resolution gas chromatography-mass spectrometry in conjunction with stable isotope dilution analysis, leading to the determination of apparent permeability values by different mathematical approaches considering sink and non-sink conditions. Overall, calculated permeability values ranged from 2.6 × 10(-6) to 1.8 × 10(-4) cm s(-1) with all mathematical approaches, indicating high absorption potential and almost complete bioavailability for all tested compounds with hydroxyl-functionalities. Considering this high permeability together with the high lipophilicity of these substances, a passive transcellular uptake route can be speculated. Investigated sesquiterpenes and β-myrcene showed flat absorption profiles while the investigated esters showed decreasing profiles. In view of the lipophilic and volatile nature of the investigated substances, special attention was paid to recovery and mass balance determination. Furthermore, in the course of the transport experiments of 1-octen-3-ol and 3-methyl-2-buten-1-ol, additional biotransformation products were observed, namely 3-octanone and 3-methyl-2-butenal, respectively. The absence of these additional substances in control experiments strongly indicates an intestinal first-pass metabolism of the α,β-unsaturated alcohols 1-octen-3-ol and 3-methyl-2-buten-1-ol in Caco-2 cells.

Identification of tert-Butyl Cations in Zeolite H-ZSM-5: Evidence from NMR Spectroscopy and DFT Calculations.

PubMed

Dai, Weili; Wang, Chuanming; Yi, Xianfeng; Zheng, Anmin; Li, Landong; Wu, Guangjun; Guan, Naijia; Xie, Zaiku; Dyballa, Michael; Hunger, Michael

2015-07-20

Experimental evidence for the presence of tert-butyl cations, which are important intermediates in acid-catalyzed heterogeneous reactions, on solid acids has still not been provided to date. By combining density functional theory (DFT) calculations with (1)H/(13)C magic-angle-spinning NMR spectroscopy, the tert-butyl cation was successfully identified on zeolite H-ZSM-5 upon conversion of isobutene by capturing this intermediate with ammonia. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nonleaded Gasoline: Its Impact on the Chemical Industry.

ERIC Educational Resources Information Center

Wittcoff, Harold

1987-01-01

Explores some of the ways that lead is being replaced in the production of gasolines. Discusses the effects these changes are having on the chemical industry. Contrasts the use of ethyl alcohol from renewable sources with alcohols depending on the availability of isobutene. (TW)

Observation of H displacement and H2 elimination channels in the reaction of O(3P) with 1-butene from crossed beams and theoretical studies

NASA Astrophysics Data System (ADS)

Caracciolo, Adriana; Vanuzzo, Gianmarco; Balucani, Nadia; Stranges, Domenico; Cavallotti, Carlo; Casavecchia, Piergiorgio

2017-09-01

We report preliminary combined experimental/theoretical results on O(3P) + 1-butene reaction dynamics with focus on atomic hydrogen displacement and molecular hydrogen elimination channels. Dynamics and relative yield of the ethylvinoxy + H and ethylketene + H2 product channels are characterized in crossed beam experiments. Stationary points and energetics of triplet/singlet C4H8O potential energy surfaces (PESs) are calculated at CCSD(T)/CBS and CASPT2 level. O(3P) attack occurs on both unsaturated C-atoms with preference for the less substituted one leading, among other products, to C2H5CHCHO + H via an exit barrier on the triplet PES, and to C2H5CHCO + H2 via a very high exit barrier on the singlet PES following intersystem crossing.

Hydrogenation of 1-butene on nanosized Pd/ZnO catalysts.

PubMed

Agelakopoulou, T; Roubani-Kalantzopoulou, F

2008-07-25

The reaction concerning the hydrogenation of 1-butene has occupied the researchers conducting research based on the method of reversed-flow inverse gas chromatography (RF-IGC), for extended time periods. This work aims to define and record, with the utmost accuracy, the phenomena and their possible parallel reactions. It was a challenge for the RF-IGC, which was met. The venture consisted of many parts. Answers had to be provided to the following questions: (a) Can RF-IGC deal with issues of catalysis? (b) Can RF-IGC be applied to thin films? (c) Can RF-IGC identify peaks? (d) Can RF-IGC define the gnostic regions of adsorption, desorption, surface diffusion, surface reaction, the existence of more than one reaction? (e) Can it kinetically follow the above? The answer is certainly yes. The effort made is presented in this work and aims to answer all the above questions.

Dehydration of isobutanol and the elimination of water from fuel alcohols.

PubMed

Rosado-Reyes, Claudette M; Tsang, Wing; Alecu, Ionut M; Merchant, Shamel S; Green, William H

2013-08-08

Rate coefficients for the dehydration of isobutanol have been determined experimentally from comparative rate single pulse shock tube measurements and calculated via multistructural transition state theory (MS-TST). They are represented by the Arrhenius expression, k(isobutanol → isobutene + H2O)(experimental) = 7.2 × 10(13) exp(-35300 K/T) s(-1). The theoretical work leads to the high pressure rate expression, k(isobutanol → isobutene + H2O)(theory) = 3.5 × 10(13) exp(-35400 K/T) s(-1). Results are thus within a factor of 2 of each other. The experimental results cover the temperature range 1090-1240 K and pressure range 1.5-6 atm, with no discernible pressure effects. Analysis of these results, in combination with earlier single pulse shock tube work, made it possible to derive the governing factors that control the rate coefficients for alcohol dehydration in general. Alcohol dehydration rate constants depend on the location of the hydroxyl group (primary, secondary, and tertiary) and the number of available H-atoms adjacent to the OH group for water elimination. The position of the H-atoms in the hydrocarbon backbone appears to be unimportant except for highly substituted molecules. From these correlations, we have derived k(isopropanol → propene + H2O) = 7.2 × 10(13) exp(-33000 K/T) s(-1). Comparison of experimental determination with theoretical calculations for this dehydration, and those for ethanol show deviations of the same magnitude as for isobutanol. Systematic differences between experiments and theoretical calculations are common.

Catalytic conversion of cellulose to liquid hydrocarbon fuels by progressive removal of oxygen to facilitate separation processes and achieve high selectivities

DOEpatents

Dumesic, James A.; Ruiz, Juan Carlos Serrano; West, Ryan M.

2015-06-30

Described is a method to make liquid chemicals. The method includes deconstructing cellulose to yield a product mixture comprising levulinic acid and formic acid, converting the levulinic acid to .gamma.-valerolactone, and converting the .gamma.-valerolactone to pentanoic acid. Alternatively, the .gamma.-valerolactone can be converted to a mixture of n-butenes. The pentanoic acid can be decarboxylated yield 1-butene or ketonized to yield 5-nonanone. The 5-nonanone can be hydrodeoxygenated to yield nonane, or 5-nonanone can be reduced to yield 5-nonanol. The 5-nonanol can be dehydrated to yield nonene, which can be dimerized to yield a mixture of C.sub.9 and C.sub.18 olefins, which can be hydrogenated to yield a mixture of alkanes.

Catalytic conversion of cellulose to liquid hydrocarbon fuels by progressive removal of oxygen to facilitate separation processes and achieve high selectivities

DOEpatents

Dumesic, James A [Verona, WI; Ruiz, Juan Carlos Serrano [Madison, WI; West, Ryan M [Madison, WI

2014-01-07

Described is a method to make liquid chemicals. The method includes deconstructing cellulose to yield a product mixture comprising levulinic acid and formic acid, converting the levulinic acid to .gamma.-valerolactone, and converting the .gamma.-valerolactone to pentanoic acid. Alternatively, the .gamma.-valerolactone can be conveted to a mixture of n-butenes. The pentanoic acid can be decarboxylated yield 1-butene or ketonized to yield 5-nonanone. The 5-nonanone can be hydrodeoxygenated to yield nonane, or 5-nonanone can be reduced to yield 5-nonanol. The 5-nonanol can be dehydrated to yield nonene, which can be dimerized to yield a mixture of C.sub.9 and C.sub.18 olefins, which can be hydrogenated to yield a mixture of alkanes.

Flowers of Clerodendrum volubile exacerbate immunomodulation by suppressing phagocytic oxidative burst and modulation of COX-2 activity.

PubMed

Erukainure, Ochuko L; Mesaik, Ahmed M; Muhammad, Aliyu; Chukwuma, Chika I; Manhas, Neha; Singh, Parvesh; Aremu, Oluwole S; Islam, Md Shahidul

2016-10-01

The immunomodulatory potentials of the crude methanolic extract and fractions [n-hexane (Hex), n-dichloromethane (DCM), ethyl acetate (EtOAc) and n-butanol (BuOH)] of Clerodendrum volubile flowers were investigated on whole blood phagocytic oxidative burst using luminol-amplified chemiluminescence technique. They were also investigated for their free radicals scavenging activities. The DCM fraction showed significant (p<0.05) anti-oxidative burst and free radical scavenging activities indicating high immunomodulatory and antioxidant potencies respectively. Cytotoxicity assay of the DCM fraction revealed a cytotoxic effect on CC-1 normal cell line. GCMS analysis revealed the presence of triacetin; 3,6-dimethyl-3-octanol; 2R - Acetoxymethyl-1,3,3-trimethtyl - 4t - (3-methyl-2-buten-1-yl) - 1c - cyclohexanol and Stigmastan - 3,5-diene in DCM fraction. These compounds were docked with the active sites of cyclooxygenase-2 (COX-2). Triacetin, 3,6-dimethyl-3-Octanol, and 2R-Acetoxymethyl-1,3,3-trimethtyl-4t-(3-methyl-2-buten-1-yl)-1c-cyclohexanol docked comfortably with COX-2 with good scoring function (-CDocker energy) indicating their inhibitory potency against COX-2. 3,6-dimethyl-3-Octanol, displayed the lowest predicted free energy of binding (-21.4kcalmol -1 ) suggesting its stronger interaction with COX-2, this was followed by 2R - Acetoxymethyl-1, 3, 3-trimethtyl-4t-(3-methyl-2-buten-1-yl)-1c-cyclhexanol (BE=-20.5kcalmol -1 ), and triacetin (BE=-10.9kcalmol -1 ). Stigmastan - 3,5-diene failed to dock with COX-2. The observed suppressive effect of the DCM fraction of C. volubile flower methanolic extract on phagocytic oxidative burst indicates an immunomodulatory potential. This is further reflected in its free scavenging activities and synergetic modulation of COX-2 activities by its identified compounds in silico. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

FAGE measurements of tropospheric HO with measurements and model of interferences

NASA Technical Reports Server (NTRS)

Hard, T. M.; Mehrabzadeh, A. A.; Chan, C. Y.; O'Brien, R. J.

1992-01-01

Ambient HO measurements by low-pressure laser-excited fluorescence with chemical modulation, and supporting ozone and water-vapor data, are presented for periods in May and August 1987. The observed peak daytime ambient HO concentrations are in the range (2.5 to 8) x 10 exp 6 molecules/cu cm and show small negative offsets due to photochemical interference. Direct measurements of the interference at fixed (O3) give the dependence on ambient (H2O) and on the modulating reagent (isobutane). At ambient (O3) = 30 ppb and 10 torr H2O, with excitation and detection at a total pressure of 4 torr, the net interference is equal to (HO) = -1.3 x 10 exp 6 molecules/cu cm. Production of HO by the reaction of isobutane with O(1D) accounts for the negative interference. Quenching of HO fluorescence by the modulating reagent contributes a smaller positive term to the interference; kinetic measurements of the quenching rate coefficient are reported. The experimental interference results are compared with a detailed kinetic model of HO production, excitation, relaxation, and detection; reasonable agreement is found.

Addressing the selectivity issue of cobalt doped zinc oxide thin film iso-butane sensors: Conductance transients and principal component analyses

NASA Astrophysics Data System (ADS)

Ghosh, A.; Majumder, S. B.

2017-07-01

Iso-butane (i-C4H10) is one of the major components of liquefied petroleum gas which is used as fuel in domestic and industrial applications. Developing chemi-resistive selective i-C4H10 thin film sensors remains a major challenge. Two strategies were undertaken to differentiate carbon monoxide, hydrogen, and iso-butane gases from the measured conductance transients of cobalt doped zinc oxide thin films. Following the first strategy, the response and recovery transients of conductances in these gas environments are fitted using the Langmuir adsorption kinetic model to estimate the heat of adsorption, response time constant, and activation energies for adsorption (response) and desorption (recovery). Although these test gases have seemingly different vapor densities, molecular diameters, and reactivities, analyzing the estimated heat of adsorption and activation energies (for both adsorption and desorption), we could not differentiate these gases unequivocally. However, we have found that the lower the vapor density, the faster the response time irrespective of the test gas concentration. As a second strategy, we demonstrated that feature extraction of conductance transients (using fast Fourier transformation) in conjunction with the pattern recognition algorithm (principal component analysis) is more fruitful to address the cross-sensitivity of Co doped ZnO thin film sensors. We have found that although the dispersion among different concentrations of hydrogen and carbon monoxide could not be avoided, each of these three gases forms distinct clusters in the plot of principal component 2 versus 1 and therefore could easily be differentiated.

THE OZONE REACTION WITH BUTADIENE: FORMATION OF TOXIC PRODUCTS. (R826236)

EPA Science Inventory

Abstract

The formation yields of acrolein, 1,2-epoxy-3-butene and OH radicals have been measured from reaction of ozone with 1,3-butadiene at room temperature and atmosphere pressure. 1,3,5-Trimethyl benzene was added to scavenge OH radicals in measurements of product ...

The Thermodynamic Conjugation Stabilization of 1,3-Butadiyne Is Zero

ERIC Educational Resources Information Center

Rogers, Donald W.; Zavitsas, Andreas A.; Matsunaga, Nikita

2010-01-01

Many textbooks point out that the thermodynamic stabilization enthalpy of 1 mol of 1,3-butadiene relative to 2 mol of 1-butene or to 1 mol of 1,4-pentadiene is slightly less than 4 kcal mol[superscript -1], owing to conjugation between the double bonds in the 1,3 configuration. It is reasonable to suppose that the analogous thermochemical…

THE GAS PHASE REACTION OF OZONE WITH 1,3-BUTADIENE: FORMATION YIELDS OF SOME TOXIC PRODUCTS. (R826236)

EPA Science Inventory

The formation yields of acrolein, 1,2-epoxy-3-butene and OH radicals have been measured from reaction of ozone with 1,3-butadiene at room temperature and atmosphere pressure. 1,3,5-Trimethyl benzene was added to scavenge OH radicals in measurements of product yields. In separa...

Catalytic oxidation of light alkanes in presence of a base

DOEpatents

Bhinde, M.V.; Bierl, T.W.

1998-03-03

The presence of a base in the reaction mixture in a metal-ligand catalyzed partial oxidation of alkanes results in sustained catalyst activity, and in greater percent conversion as compared with oxidation in the absence of base, while maintaining satisfactory selectivity for the desired oxidation, for example the oxidation of isobutane to isobutanol. 1 fig.

Temporal variation of VOC fluxes measured with PTR-TOF above a boreal forest

NASA Astrophysics Data System (ADS)

Schallhart, Simon; Rantala, Pekka; Kajos, Maija K.; Aalto, Juho; Mammarella, Ivan; Ruuskanen, Taina M.; Kulmala, Markku

2018-01-01

Between April and June 2013 fluxes of volatile organic compounds (VOCs) were measured in a Scots pine and Norway spruce forest using the eddy covariance (EC) method with a proton transfer reaction time-of-flight (PTR-TOF) mass spectrometer. The observations were performed above a boreal forest at the SMEAR II site in southern Finland.We found a total of 25 different compounds with exchange and investigated their seasonal variations from spring to summer. The majority of the net VOC flux was comprised of methanol, monoterpenes, acetone and butene + butanol. The butene + butanol emissions were concluded to not originate from the forest and, therefore, be anthropogenic. The VOC exchange followed a seasonal trend and the emissions increased from spring to summer. Only three compounds were emitted during the snowmelt while in summer emissions of some 19 VOCs were observed. During the measurement period in April, the emissions were dominated by butene + butanol, while during the start of the growing season and in summer, methanol was the most emitted compound. The main source of methanol was likely the growth of new biomass. During a 21-day period in June, the net VOC flux was 2.1 nmol m-2 s-1. This is on the lower end of PTR-TOF flux measurements from other ecosystems, which range from 2 to 10 nmol m-2 s-1. The EC flux results were compared with surface layer profile measurements, using a proton transfer reaction quadrupole mass spectrometer, which is permanently installed at the SMEAR II site. For the major compounds, the fluxes measured with the two different methods agreed well.

Chemical kinetic model uncertainty minimization through laminar flame speed measurements.

PubMed

Park, Okjoo; Veloo, Peter S; Sheen, David A; Tao, Yujie; Egolfopoulos, Fokion N; Wang, Hai

2016-10-01

Laminar flame speed measurements were carried for mixture of air with eight C 3-4 hydrocarbons (propene, propane, 1,3-butadiene, 1-butene, 2-butene, iso -butene, n -butane, and iso -butane) at the room temperature and ambient pressure. Along with C 1-2 hydrocarbon data reported in a recent study, the entire dataset was used to demonstrate how laminar flame speed data can be utilized to explore and minimize the uncertainties in a reaction model for foundation fuels. The USC Mech II kinetic model was chosen as a case study. The method of uncertainty minimization using polynomial chaos expansions (MUM-PCE) (D.A. Sheen and H. Wang, Combust. Flame 2011, 158, 2358-2374) was employed to constrain the model uncertainty for laminar flame speed predictions. Results demonstrate that a reaction model constrained only by the laminar flame speed values of methane/air flames notably reduces the uncertainty in the predictions of the laminar flame speeds of C 3 and C 4 alkanes, because the key chemical pathways of all of these flames are similar to each other. The uncertainty in model predictions for flames of unsaturated C 3-4 hydrocarbons remain significant without considering fuel specific laminar flames speeds in the constraining target data set, because the secondary rate controlling reaction steps are different from those in the saturated alkanes. It is shown that the constraints provided by the laminar flame speeds of the foundation fuels could reduce notably the uncertainties in the predictions of laminar flame speeds of C 4 alcohol/air mixtures. Furthermore, it is demonstrated that an accurate prediction of the laminar flame speed of a particular C 4 alcohol/air mixture is better achieved through measurements for key molecular intermediates formed during the pyrolysis and oxidation of the parent fuel.

21 CFR 573.310 - Crambe meal, heat toasted.

Code of Federal Regulations, 2012 CFR

2012-04-01

...; oil, not more than 4 percent; crude protein, not less than 24 percent; crude fiber, not more than 26 percent; glucosinolate calculated as epi-progoitrin, not more than 4 percent; goitrin, not more than 0.1 percent; nitrile calculated as 1-cyano-2-hydroxy-3-butene, not more than 1.4 percent. At least 50 percent...

21 CFR 573.310 - Crambe meal, heat toasted.

Code of Federal Regulations, 2010 CFR

2010-04-01

...; oil, not more than 4 percent; crude protein, not less than 24 percent; crude fiber, not more than 26 percent; glucosinolate calculated as epi-progoitrin, not more than 4 percent; goitrin, not more than 0.1 percent; nitrile calculated as 1-cyano-2-hydroxy-3-butene, not more than 1.4 percent. At least 50 percent...

21 CFR 573.310 - Crambe meal, heat toasted.

Code of Federal Regulations, 2013 CFR

2013-04-01

...; oil, not more than 4 percent; crude protein, not less than 24 percent; crude fiber, not more than 26 percent; glucosinolate calculated as epi-progoitrin, not more than 4 percent; goitrin, not more than 0.1 percent; nitrile calculated as 1-cyano-2-hydroxy-3-butene, not more than 1.4 percent. At least 50 percent...

21 CFR 573.310 - Crambe meal, heat toasted.

Code of Federal Regulations, 2014 CFR

2014-04-01

...; oil, not more than 4 percent; crude protein, not less than 24 percent; crude fiber, not more than 26 percent; glucosinolate calculated as epi-progoitrin, not more than 4 percent; goitrin, not more than 0.1 percent; nitrile calculated as 1-cyano-2-hydroxy-3-butene, not more than 1.4 percent. At least 50 percent...

21 CFR 573.310 - Crambe meal, heat toasted.

Code of Federal Regulations, 2011 CFR

2011-04-01

...; oil, not more than 4 percent; crude protein, not less than 24 percent; crude fiber, not more than 26 percent; glucosinolate calculated as epi-progoitrin, not more than 4 percent; goitrin, not more than 0.1 percent; nitrile calculated as 1-cyano-2-hydroxy-3-butene, not more than 1.4 percent. At least 50 percent...

THERMOCHEMICAL KINETIC ANALYSIS ON THE REACTIONS OF ALLYCIC ISOBUTENYL RADICAL WITH O2: AN ELEMENTARY REACTION MECHANISM FOR ISOBUTENE OXIDATION. (R824970)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

Extreme Pressure Synergistic Mechanism of Bismuth Naphthenate and Sulfurized Isobutene Additives

NASA Astrophysics Data System (ADS)

Xu, Xin; Hu, Jianqiang; Yang, Shizhao; Xie, Feng; Guo, Li

A four-ball tester was used to evaluate the tribological performances of bismuth naphthenate (BiNap), sulfurized isobutene (VSB), and their combinations. The results show that the antiwear properties of BiNap and VSB are not very visible, but they possess good extreme pressure (EP) properties, particularly sulfur containing bismuth additives. Synergistic EP properties of BiNap with various sulfur-containing additives were investigated. The results indicate that BiNap exhibits good EP synergism with sulfur-containing additives. The surface analytical tools, such as X-ray photoelectron spectrometer (XPS) scanning electron microscope (SEM) and energy dispersive X-ray (EDX), were used to investigate the topography, composition contents, and depth profile of some typical elements on the rubbing surface. Smooth topography of wear scar further confirms that the additive showed good EP capacities, and XPS and EDX analyzes indicate that tribochemical mixed protective films composed of bismuth, bismuth oxides, sulfides, and sulfates are formed on the rubbing surface, which improves the tribological properties of lubricants. In particular, a large number of bismuth atoms and bismuth sulfides play an important role in improving the EP properties of oils.

40 CFR 60.707 - Chemicals affected by subpart RRR.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 123-42-2 1,4-Dichlorobutene 110-57-6 3,4-Dichloro-1-butene 64037-54-3 Dichlorodifluoromethane 75-71-8... Ethyl chloride 75-00-3 Ethylene 74-85-1 Ethylene dibromide 106-93-4 Ethylene dichloride 107-06-2...-7 (2-Ethylhexyl) amine 104-75-6 6-Ethyl-1,2,3,4-tetrahydro 9,10-anthracenedione 15547-17-8...

H Abstraction Channels in the Crossed-Beam Reaction of F + 1-Propanol, 1-Butene and 1-Hexene by DC Slice Imaging.

PubMed

Shi, Yuanyuan; Kamasah, Alexander; Suits, Arthur G

2016-11-17

We report a crossed molecular beam study of the reaction dynamics of fluorine atom with 1-propanol, 1-butene, and 1-hexene. The product alkoxy and alkenyl radicals were detected via dc slice imaging by 157 nm single photon ionization at collision energies around 10 kcal mol -1 . The analyzed data is interpreted with the aid of theoretical investigation of the relevant potential energy surfaces. The translational energy distribution and center-of-mass angular distribution of F + 1-propanol is quite similar to our previous results for F + n-butane, albeit with an increased fraction of the available energy in translation. In F atom reaction with alkenes, we also detected the HF formation channel. The low translational energy release and presence of significant backward scattering suggests the importance of an addition/elimination mechanism. Our selective single photon ionization probe allows us to examine the dynamics in minor channels in these systems. Although the probe is not sensitive to reaction at vinylic H sites, theoretical calculations consistently suggest a lower barrier from the addition complex to HF elimination involving vinylic H atoms.

Effects of biomass burning on summertime nonmethane hydrocarbon concentrations in the Canadian wetlands

NASA Technical Reports Server (NTRS)

Blake, D. R.; Smith, T. W., Jr.; Chen, T.-Y.; Whipple, W. J.; Rowland, F. S.

1994-01-01

Approximately 900 whole air samples were collected and assayed for selected C2-C10 hydrocarbons and seven halocarbons during the 5-week Arctic Boundary Layer Expedition (ABLE) 3B conducted in eastern Canadian wetland areas. In more than half of the 46 vertical profiles flown, enhanced nonmethane hydrocarbon (NMHC) concentrations attributable to plumes from Canadian forest fires were observed. Urban plumes, also enhanced in many NMHCs, were separately identified by their high correlation with elevated levels of perchloroethene. Emission factors relative to ethane were determined for 21 hydrocarbons released from Canadian biomass burning. Using these data for ethane, ethyne, propane, n-butane, and carbon monoxide enhancements from the literature, global emissions of these four NMHCs were estimated. Because of its very short atmospheric lifetime and its below detection limit background mixing ratio, 1,3-butadiene is an excellent indicator of recent combustion. No statistically significant emissions of nitrous oxide, isoprene, or CFC 12 were observed in the biomass-burning plumes encountered during ABLE 3B. The presence of the short-lived biogenically emitted isoprene at altitudes as high as 3000 m implies that mixing within the planetary boundary layer (PBL) was rapid. Although background levels of the longer-lived NMHCs in this Canadian region increase during the fire season, isoprene still dominated local hydroxyl radical photochemistry within the PBL except in the immediate vicinity of active fires. The average biomass-burning emission ratios for hydrocarbons from an active fire sampled within minutes of combustion were, relative to ethane, ethene, 2.45; ethyne 0.57; propane, 0.25; propene, 0.73; propyne, 0.06; n-butane, 0.09; i-butane, 0.01; 1-butene, 0.14; cis-2-butene, 0.02; trans-2-butene, 0.03; i-butylene, 0.07; 1,3-butadiene, 0.12; n-pentane, 0.05; i-pentane, 0.03; 1-pentene, 0.06; n-hexane, 0.05; 1-hexene, 0.07; benzene, 0.37; toluene, 0.16.

Reactions of Atomic Carbon with Butene Isomers: Implications for Molecular Growth in Carbon-Rich Environments

DOE PAGES

Bourgalais, J.; Spencer, Michael; Osborn, David L.; ...

2016-10-31

We carried out the product detection studies of C( 3P) atom reactions with butene (C 4H 8) isomers (but-1-ene, cis-but-2-ene, trans-but-2-ene) in a flow tube reactor at 353 K and 4 Torr under multiple collision conditions. Ground state carbon atoms are generated by 248 nm laser photolysis of tetrabromomethane, CBr 4, in a buffer of helium. Thermalized reaction products are detected using synchrotron tunable VUV photoionization and time-of-flight mass spectrometry. The temporal profiles of the detected ions are used to discriminate products from side or secondary reactions. Furthermore, for the C( 3P) + trans-but-2-ene and C( 3P) + cis-but-2-ene reactions,more » various isomers of C 4H 5 and C 5H 7 are identified as reaction products formed via CH 3 and H elimination. Assuming equal ionization cross sections for all C 4H 5 and C 5H 7 isomers, C 4H 5:C 5H 7 branching ratios of 0.63:1 and 0.60:1 are derived for the C( 3P) + trans-but-2-ene and the C( 3P) + cis-but-2-ene reactions, respectively. For the C( 3P) + but-1-ene reaction, two reaction channels are observed: the H-elimination channel, leading to the formation of the ethylpropargyl isomer, and the C 3H 3 + C 2H 5 channel. Assuming equal ionization cross sections for ethylpropargyl and C 3H 3 radicals, a branching ratio of 1:0.95 for the C 3H 3 + C 2H 5 and H + ethylpropargyl channels is derived. Finally, the experimental results are compared to previous H atom branching ratios and used to propose the most likely mechanisms for the reaction of ground state carbon atoms with butene isomers.« less

Catalytic conversion of cellulose to liquid hydrocarbon fuels by progressive removal of oxygen to facilitate separation processes and achieve high selectivities

DOEpatents

Dumesic, James A [Verona, WI; Ruiz, Juan Carlos Serrano [Madison, WI; West, Ryan M [Madison, WI

2012-04-03

Described is a method to make liquid chemicals, such as functional intermediates, solvents, and liquid fuels from biomass-derived cellulose. The method is cascading; the product stream from an upstream reaction can be used as the feedstock in the next downstream reaction. The method includes the steps of deconstructing cellulose to yield a product mixture comprising levulinic acid and formic acid, converting the levulinic acid to .gamma.-valerolactone, and converting the .gamma.-valerolactone to pentanoic acid. Alternatively, the .gamma.-valerolactone can be converted to a mixture of n-butenes. The pentanoic acid so formed can be further reacted to yield a host of valuable products. For example, the pentanoic acid can be decarboxylated yield 1-butene or ketonized to yield 5-nonanone. The 5-nonanone can be hydrodeoxygenated to yield nonane, or 5-nonanone can be reduced to yield 5-nonanol. The 5-nonanol can be dehydrated to yield nonene, which can be dimerized to yield a mixture of C.sub.9 and C.sub.18 olefins, which can be hydrogenated to yield a mixture of alkanes. Alternatively, the nonene may be isomerized to yield a mixture of branched olefins, which can be hydrogenated to yield a mixture of branched alkanes. The mixture of n-butenes formed from .gamma.-valerolactone can also be subjected to isomerization and oligomerization to yield olefins in the gasoline, jet and Diesel fuel ranges.

DEVELOPMENT OF A PHYSIOLOGICALLY-BASED PHARMACOKINETIC (PBPK) MODEL FOR THE INHALATION OF 2,2,4-TRIMETHYLPENTANE (TMP) IN LONG EVANS RATS.

EPA Science Inventory

TMP (2,2,4-trimethylpentane,“isooctane”) is a colorless liquid used primarily in the alkylation of isobutene and butylene reactions to derive high-octane fuels. TMP is released in the environment through the manufacture, use, and disposal of products associated with the gasoline ...

49 CFR 173.313 - UN Portable Tank Table for Liquefied Compressed Gases.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 28.0 Allowed Normal 0.43 24.5 22.0 20.0 1078 Refrigerant gas, n.o.s. See MAWP definition in § 178.276..., flammable, n.o.s. See MAWP definition in § 178.276(a) Allowed Normal § 173.32(f) 1958 1,2-Dichloro-1,1,2,2... liquefied, n.o.s. See MAWP definition in 178.276(a) Allowed Normal See § 173.32(f) 1969 Isobutane 8.5...

Open-cage fullerene-like graphitic carbons as catalysts for oxidative dehydrogenation of isobutane.

PubMed

Liang, Chengdu; Xie, Hong; Schwartz, Viviane; Howe, Jane; Dai, Sheng; Overbury, Steven H

2009-06-10

We report herein a facile synthesis of fullerene-like cages, which can be opened and closed through simple thermal treatments. A glassy carbon with enclosed fullerene-like cages of 2-3 nm was synthesized through a soft-template approach that created open mesopores of 7 nm. The open mesopores provided access to the fullerene-like cages, which were opened and closed through heat treatments in air and inert gas at various temperatures. Catalytic measurements showed that the open cages displayed strikingly higher activity for the oxidative dehydrogenation of isobutane in comparison to the closed ones. We anticipate that this synthesis approach could unravel an avenue for pursuing fundamental understanding of the unique catalytic properties of graphitic carbon nanostructures.

Measuring urinary N-acetyl-S-(4-hydroxy-2-methyl-2-buten-1-yl)-L-cysteine (IPMA3) as a potential biomarker of isoprene exposure.

PubMed

Alwis, K Udeni; Bailey, T Liz; Patel, Dhrusti; Wang, Liqun; Blount, Benjamin C

2016-10-19

Isoprene, the 2-methyl analog of 1,3-butadiene, is identified as a possible human carcinogen by the International Agency for Research on Cancer (IARC). Isoprene is ubiquitous in the environment with numerous natural and anthropogenic sources. Tobacco smoke is the main exogenous source of isoprene exposure in indoor environments. Among smoke constituents, isoprene is thought to contribute significantly to cancer risk; however, no selective urinary biomarkers of isoprene exposure have been identified for humans. In this manuscript, we measured the minor isoprene metabolite IPMA1 (mixture of N-acetyl-S-(1-[hydroxymethyl]-2-methyl-2-propen-1-yl)-L-cysteine and N-acetyl-S-(2-hydroxy-3-methyl-3-buten-1-yl)-L-cysteine), and we identified IPMA3 (N-acetyl-S-(4-hydroxy-2-methyl-2-buten-1-yl)-L-cysteine) as a major isoprene metabolite and novel isoprene exposure biomarker for humans. Urinary isoprene metabolites were measured using ultra high performance liquid chromatography coupled with electrospray ionization triple quad tandem mass spectrometry (UPLC/ESI-MSMS). The detection rates of IPMA1 and IPMA3 are <20% and 82%, respectively. The selectivity and abundance of IPMA3 make it a useful urinary biomarker of isoprene exposure. The limit of detection of IPMA3 in urine was 0.5 ng mL -1 . IPMA3 was stable under different storage temperatures and following ten freeze-thaw cycles. The average recovery of urine spiked with IPMA3 at three different levels was 99%. IPMA3 was measured in urine samples received from 75 anonymous subjects; the median (25th percentile, 75th percentile) IPMA3 level in smokers was 36.2 (18.2, 56.8) ng mL -1 and non-smokers 2.31 (2.31, 4.38) ng mL -1 . Application of this method to large population studies will help to characterize isoprene exposure and assess potential health impact. Published by Elsevier B.V.

Products from the Oxidation of n-Butane from 298 to 735 K Using Either Cl Atom or Thermal Initiation: Formation of Acetone and Acetic Acid-Possible Roaming Reactions?

PubMed

Kaiser, E W; Wallington, T J

2017-11-16

The oxidation of 2-butyl radicals (and to a lesser extent 1-butyl radicals) has been studied over the temperature range of 298-735 K. The reaction of Cl atoms (formed by 360 nm irradiation of Cl 2 ) with n-butane generated the 2-butyl radicals in mixtures of n-C 4 H 10 , O 2 , and Cl 2 at temperatures below 600 K. Above 600 K, 2-butyl radicals were produced by thermal combustion reactions in the absence of chlorine. The yields of the products were measured by gas chromatography using a flame ionization detector. Major products quantified include acetone, acetic acid, acetaldehyde, butanone, 2-butanol, butanal, 1- and 2- chlorobutane, 1-butene, trans-2-butene, and cis-2-butene. At 298 K, the major oxygenated products are those expected from bimolecular reactions of 2-butylperoxy radicals (butanone, 2-butanol, and acetaldehyde). As the temperature rises to 390 K, the butanone decreases while acetaldehyde increases because of the increased rate of 2-butoxy radical decomposition. Acetone and acetic acid first appear in significant yield near 400 K, and these species rise slowly at first and then sharply, peaking near 525 K at yields of ∼25 and ∼20 mol %, respectively. In the same temperature range (400-525 K), butanone, acetaldehyde, and 2-butanol decrease rapidly. This suggests that acetone and acetic acid may be formed by previously unknown reaction channels of the 2-butylperoxy radical, which are in competition with those that lead to butanone, acetaldehyde, and 2-butanol. Above 570 K, the yields of acetone and acetic acid fall rapidly as the yields of the butenes rise. Experiments varying the Cl atom density, which in turn controls the entire radical pool density, were performed in the temperature range of 410-440 K. Decreasing the Cl atom density increased the yields of acetone and acetic acid while the yields of butanone, acetaldehyde, and 2-butanol decreased. This is consistent with the formation of acetone and acetic acid by unimolecular decomposition channels of the 2-butylperoxy radical, which are in competition with the bimolecular channels that form butanone, acetaldehyde, and 2-butanol. Such unimolecular decomposition channels would be unlikely to proceed through conventional transition states because those states would be very constrained. Therefore, the possibility that these decomposition channels proceed via roaming should be considered. In addition, we investigated and were unable to fit our data trends by a simplified ketohydroperoxide mechanism.

Improved method for mutagenicity testing of gaseous compounds by using a gas sampling bag.

PubMed

Araki, A; Noguchi, T; Kato, F; Matsushima, T

1994-05-01

A simple and safety gas exposure method was developed using a gas sampling bag as an exposure vessel and a preparation vessel of diluted gas. The gas exposure conditions such as amount of S9 in the plate, volume of gas for the plate, amount of top agar, exposure period and exposure temperature were examined by mutagenicity testing of 1,3-butadiene using the gas sampling bag. Mutagenicity tests of 14 compounds and 1,3-butadiene on S. typhimurium TA98, TA100, TA1535 and TA1537, and E. coli WP2 uvrA were also examined by the developed gas exposure method. 1,3-Butadiene, propyne (methyl acetylene), monochlorodifluoromethane, ethylchloride, diborane and silane were mutagenic. 1-Butene, 2-butene, 2-methylpropene, methyl vinyl ether, trichlorofluoromethane, dichlorodifluoromethane, 1,2-dichloro-1,1,2,2-tetrafluoroethane, 1,1-difluoroethane and phosphine were not mutagenic on S. typhimurium TA98, TA100, TA1535 and TA1537, and E. coli WP2 uvrA with or without metabolic activation. These results were compatible with a previous report, and this developed method has the advantage that it can be tested easily and safely for combustible and self-combustible substances such as 1,3-butadiene and silane.

40 CFR 60.489 - List of chemicals produced by affected facilities.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... 75-07-0 Acetaldehyde. 107-89-1 Acetaldol. 60-35-5 Acetamide. 103-84-4 Acetanilide. 64-19-7 Acetic.... 119-53-9 Benzoin. 100-47-0 Benzonitrile. 119-61-9 Benzophenone. 98-07-7 Benzotrichloride. 98-88-4...-4 Bromonaphthalene. 106-99-0 Butadiene. 106-98-9 1-butene. 123-86-4 n-butyl acetate. 141-32-2 n...

Difference in the volatile composition of pine-mushrooms (Tricholoma matsutake Sing.) according to their grades.

PubMed

Cho, In Hee; Choi, Hyung-Kyoon; Kim, Young-Suk

2006-06-28

The differences in volatile components of pine-mushrooms (Tricholoma matsutake Sing.) according to their grades were observed by applying multivariate statistical methods to GC-MS data sets. A total of 35 and 37 volatile components were identified in raw and cooked pine-mushrooms, respectively. The volatile components in pine-mushrooms were primarily composed of C8 species, such as 3-octanol, 1-octen-3-ol, 1-octanol, (E)-2-octen-1-ol, 3-octanone, 1-octen-3-one, (E)-2-octenal, and octanoic acid. The levels of ethyl octanoate, junipene, and 3-methyl-3-buten-2-one were much higher in raw pine-mushroom of higher grades, whereas the reverse was true for C8 components. On the other hand, furfuryl alcohol, benzyl alcohol, phenylethyl alcohol, dihydro-5-methyl-2(3H)-furanone, 2(5H)-furanone, (E)-2-methyl-2-butenal, furfural, phenylacetaldehyde, benzoic acid methyl ester, camphene, and beta-pinene were the major components of cooked mushrooms. These volatile components formed by various thermal reactions could be mainly responsible for the difference in volatile components of cooked pine-mushrooms according to their grades.

Drop-in substitute for dichlorodifluoromethane refrigerant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goble, G.H.

1993-06-01

A method for producing refrigeration in a refrigeration system designed for a dichlorodifluoromethane refrigerant is described, comprising drop-in substituting for said dichlorodifluoromethane a ternary mixture of about 2 to 20 weight percent isobutane, about 21 to 51 weight percent 1-chloro-1,1-difluoroethane, and about 41 to 71 weight percent chlorodifluoromethane, with the weight percentages of said components being weight percentages of the overall mixture; condensing said ternary mixture; and thereafter evaporating said ternary mixture in the vicinity of a body to be cooled.

49 CFR 173.313 - UN Portable Tank Table for Liquefied Compressed Gases and Chemical Under Pressure.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 28.0 Allowed Normal 0.43 24.5 22.0 20.0 1078 Refrigerant gas, n.o.s. See MAWP definition in § 178.276..., flammable, n.o.s. See MAWP definition in § 178.276(a) Allowed Normal § 173.32(f) 1958 1,2-Dichloro-1,1,2,2... liquefied, n.o.s. See MAWP definition in 178.276(a) Allowed Normal See § 173.32(f) 1969 Isobutane 8.5...

49 CFR 173.313 - UN Portable Tank Table for Liquefied Compressed Gases and Chemical Under Pressure.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 28.0 Allowed Normal 0.43 24.5 22.0 20.0 1078 Refrigerant gas, n.o.s. See MAWP definition in § 178.276..., flammable, n.o.s. See MAWP definition in § 178.276(a) Allowed Normal § 173.32(f) 1958 1,2-Dichloro-1,1,2,2... liquefied, n.o.s. See MAWP definition in 178.276(a) Allowed Normal See § 173.32(f) 1969 Isobutane 8.5...

UV and γ-ray resistance of poly(N-methylmaleimide-alt-isobutene) and poly(diisopropyl fumarate) as transparent polymer films

NASA Astrophysics Data System (ADS)

Imaizumi, Ryota; Furuta, Masakazu; Okamura, Haruyuki; Matsumoto, Akikazu

2017-09-01

UV and γ-ray resistance of transparent polymers obtained by radical polymerization of maleic and fumaric acid derivatives, i.e., an alternating copolymer of N-methylmaleimide and isobutene (PMI) and poly(diisopropyl fumarate) (PDiPF), was investigated. Transmittance in UV and visible regions of these polymers were examined after UV irradiation and compared with the results for poly(methyl methacrylate) (PMMA) and polycarbonate (PC) as conventional transparent polymers. The order of stability toward UV irradiation was PMMA≈PDiPF>PMI>>PC, deduced from changes in the transmittance of 380 nm light. Tensile mechanical properties, such as elastic modulus, maximum strength, and elongation values of PMI, PDiPF, and PMMA were also investigated after UV and γ-radiation. UV irradiation induced the side chain scission of PMI and PDiPF via Norrish I type reaction as well as crosslinking by combination between formed polymer radicals, leading to deterioration in their optical and mechanical properties. γ-radiation induced significant changes in molecular weight and mechanical properties of the polymers. In conclusion, PMI exhibited unchanged mechanical properties and PDiPF maintained its high transparency under various irradiation conditions.

A widely-tunable and sensitive optical sensor for multi-species detection in the mid-IR

NASA Astrophysics Data System (ADS)

Alquaity, Awad B. S.; Al-Saif, Bidoor; Farooq, Aamir

2018-01-01

Pulsed cavity ringdown spectroscopy (CRDS) technique was used to develop a novel widely-tunable laser-based sensor for sensitive measurements of ethylene, propene, 1-butene and allene in the mid-IR. The use of an external-cavity quantum cascade laser (EC-QCL) enabled the sensor to cover a wide wavelength range from 10 to 11.1 µm (900-1000 cm-1) to detect multiple gases relevant to combustion and environment. The sensor operation was validated in a room-temperature static cell using well-characterized absorption lines of carbon dioxide near 938.69 cm-1 and 974.62 cm-1. Detection limits for ethylene, propene, 1-butene, and allene were measured to be 17, 134, 754 and 378 ppb, respectively, at 296 K and 760 Torr for a single-pass path-length of 70 cm with averaging time of 4 ms. The excellent sensitivity of the optical sensor enabled it to measure the aforementioned gases at levels smaller than 1% of their recommended exposure limits. To the best of our knowledge, this is one of the first successful applications of the pulsed CRDS technique to measure trace levels of multiple gases in the 10-11 µm wavelength region.

Open-cage Fullerene-like Graphitic Carbons as Catalysts for Oxidative Dehydrogenation of Isobutane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang, Chengdu; Xie, Hong; Schwartz, Viviane

We report herein a facile synthesis of fullerene-like cages, which can be opened and closed through simple thermal treatments. A glassy carbon with enclosed fullerene-like cages of 2-3 nm was synthesized through a soft-template approach that created open mesopores of 7 nm. The open mesopores provided access to the fullerene-like cages, which were opened and closed through heat treatments in air and inert gas at various temperatures. Catalytic measurements showed that the open cages displayed strikingly higher activity for the oxidative dehydrogenation of isobutane in comparison to the close ones. We anticipate that this synthesis approach could unravel an avenuemore » for pursuing fundamental understanding of the unique catalytic properties of graphitic carbon nanostructures.« less

Ice core records of monoterpene- and isoprene-SOA tracers from Aurora Peak in Alaska since 1660s: Implication for climate variability in the North Pacific Rim

NASA Astrophysics Data System (ADS)

Pokhrel, A.; Kawamura, K.; Seki, O.; Ono, K.; Matoba, S.; Shiraiwa, T.

2015-12-01

180 m long ice core (ca. 343 years old) was drilled in the saddle of the Aurora Peak of Alaska, which is located southeast of Fairbanks (63.52°N; 146.54°W, elevation: 2,825 m). Samples were directly transported to the Institute of Low Temperature Science, Hokkaido University and have been analyzed for monoterpene- and isoprene-SOA tracers using gas chromatograph (GC; HP 6890) and mass spectrometry system (GC/MS; Agilent). Ice core collected from mountain glacier has not been explored for SOA yet. We found significantly high concentrations of these tracers (e.g., pinic, pinonic, and 2-methylglyceric acids, 2-methylthreitol and 2-methylrythritol), which show historical trends with good correlation with each other since 1665-2008. They show positive correlations with sugar compounds (e.g., mannitol, glucose, fructose, inositol, and sucrose), and anti-correlations with diacids (e.g., C9), w-oxocarboxylic (wC4-wC9), a-dicarbonyls and low molecular weight fatty acids (LFAs) (e.g., C18:1). LFAs show strong correlations with MSA- and nss-SO42- in the same ice core. These results suggest source regions of SOA tracers and ice core chemistry of Alaska. Concentrations of C5-alkene triols (e.g., 3-methyl-2,3,4-trihydroxy-1-butene, cis-2-methyl 1,3,4-trihydroxy-1-butene and trans-2-methyl-1,3,4-trihydroxy-1-butene) have increased in the ice core after the Great Pacific Climate Shift (late 1970's). They show positive correlations with a-dicarbonyls and LFAs (e.g., C18:1) in the ice core, suggesting that enhanced oceanic emissions of biogenic organic compounds through the surface microlayer are recorded in the ice core. Photochemical oxidation processes for these monoterpene- and isoprene-/sesquiterpene-SOA tracers are suggested to be linked with the periodicity of multi-decadal climate oscillations (e.g., North Pacific Index) and we can look at a whole range of environmental parameters in parallel with the robust reconstructed temperature changes in the Northern Hemisphere.

Volatile organic compound constituents from an integrated iron and steel facility.

PubMed

Tsai, Jiun-Horng; Lin, Kuo-Hsiung; Chen, Chih-Yu; Lai, Nina; Ma, Sen-Yi; Chiang, Hung-Lung

2008-09-15

This study measured the volatile organic compound (VOC) constituents of four processes in an integrated iron and steel industry; cokemaking, sintering, hot forming, and cold forming. Toluene, 1,2,4-trimethylbenzene, isopentane, m,p-xylene, 1-butene, ethylbenzene, and benzene were the predominant VOC species in these processes. However, some of the chlorinated compounds were high (hundreds ppbv), i.e., trichloroethylene in all four processes, carbon tetrachloride in the hot forming process, chlorobenzene in the cold forming process, and bromomethane in the sintering process. In the sintering process, the emission factors of toluene, benzene, xylene, isopentane, 1,2,4-trimethylbenzene, and ethylbenzene were over 9 g/tonne-product. In the vicinity of the manufacturing plant, toluene, isopentane, 1,2,4-trimethylbenzene, xylene and ethylbenzene were high. Toluene, 1,2,4-trimethylbenzene, xylene, 1-butene and isopentane were the major ozone formation species. Aromatic compounds were the predominant VOC groups, constituting 45-70% of the VOC concentration and contributing >70% to the high ozone formation potential in the stack exhaust and workplace air. The sequence of VOC concentration and ozone formation potential was as follows: cold forming>sintering>hot forming>cokemaking. For the workplace air, cokemaking was the highest producer, which was attributed to the fugitive emissions of the coke oven and working process release.

Catalytic production of biofuels (butene oligomers) and biochemicals (tetrahydrofurfuryl alcohol) from corn stover.

PubMed

Byun, Jaewon; Han, Jeehoon

2016-07-01

A strategy is presented that produces liquid hydrocarbon fuels (butene oligomers (BO)) from cellulose (C6) fraction and commodity chemicals (tetrahydrofurfuryl alcohol (THFA)) from hemicellulose (C5) of corn stover based on catalytic conversion technologies using 2-sec-butylphenol (SBP) solvents. This strategy integrates the conversion subsystems based on experimental studies and separation subsystems for recovery of biomass derivatives and SBP solvents. Moreover, a heat exchanger network is designed to reduce total heating requirements to the lowest level, which is satisfied from combustion of biomass residues (lignin and humins). Based on the strategy, this work offers two possible process designs (design A: generating electricity internally vs. design B: purchasing electricity externally), and performs an economic feasibility study for both the designs based on a comparison of the minimum selling price (MSP) of THFA. This strategy with the design B leads to a better MSP of $1.93 per kg THFA. Copyright © 2016 Elsevier Ltd. All rights reserved.

Study of the Synchrotron Photoionization Oxidation of 2-Methylfuran Initiated by O(3P) under Low-Temperature Conditions at 550 and 650 K.

PubMed

Fathi, Yasmin; Meloni, Giovanni

2017-09-21

The O-( 3 P)-initiated oxidation of 2-methylfuran (2-MF) was investigated using vacuum-ultraviolet synchrotron radiation from the Advanced Light Source at Lawrence Berkeley National Laboratory. Reaction species were studied by multiplexed photoionization mass spectrometry at 550 and 650 K. The oxygen addition pathway is favored in this reaction, forming four triplet diradicals that undergo intersystem crossing into singlet epoxide species that lead to the formation of products at m/z 30 (formaldehyde), 42 (propene), 54 (1-butyne, 1,3-butadiene, and 2-butyne), and 70 (2-butenal, methyl vinyl ketone, and 3-butenal). Mass-to-charge ratios, photoionization spectra, and adiabatic ionization energies for each primary reaction species were obtained and used to characterize their identities. In addition, by means of electronic structure calculations, potential energy surface scans of the different species produced throughout the oxidation were examined to further validate the primary chemistry occurring. Branching fractions for the formation of the primary products were calculated at the two temperatures and contribute 81.0 ± 21.4% at 550 K and 92.1 ± 25.5% at 650 K.

Secondary metabolites of the grapevine pathogen Eutypa lata inhibit mitochondrial respiration, based on a model bioassay using the yeast Saccharomyces cerevisiae.

PubMed

Kim, Jong H; Mahoney, Noreen; Chan, Kathleen L; Molyneux, Russell J; Campbell, Bruce C

2004-10-01

Acetylenic phenols and a chromene isolated from the grapevine fungal pathogen Eutypa lata were examined for mode of toxicity. The compounds included eutypine (4-hydroxy-3-[3-methyl-3-butene-1-ynyl] benzyl aldehyde), eutypinol (4-hydroxy-3-[3-methyl-3-butene-1-ynyl] benzyl alcohol), eulatachromene, 2- isoprenyl-5-formyl-benzofuran, siccayne, and eulatinol. A bioassay using the yeast Saccharomyces cerevisiae showed that all compounds were either lethal or inhibited growth. A respiratory assay using 2,3,5-triphenyltetrazolium (TTC) indicated that eutypinol and eulatachromene inhibited mitochondrial respiration in wild-type yeast. Bioassays also showed that 2- isoprenyl-5-formyl-benzofuran and siccayne inhibited mitochondrial respiration in the S. cerevisiae deletion mutant vph2Delta, lacking a vacuolar type H (+) ATPase (V-ATPase) assembly protein. Cell growth of tsa1Delta, a deletion mutant of S. cerevisiae lacking a thioredoxin peroxidase (cTPx I), was greatly reduced when grown on media containing eutypinol or eulatachromene and exposed to hydrogen peroxide (H(2)O(2)) as an oxidative stress. This reduction in growth establishes the toxic mode of action of these compounds through inhibition of mitochondrial respiration.

Quenching gas for detectors of charged particles

DOEpatents

Atac, M.

1974-01-22

Operation of detectors of charged particles such as wire counters and Geiger-Muller tubes is improved by filling the counters with a quenching-gas mixture of argon, isobutane and methylchloroform. (Official Gazette)

Major Groove Orientation of the (2S)-N6-(2-Hydroxy-3-buten-1-yl)-2′-deoxyadenosine DNA Adduct Induced by 1,2-Epoxy-3-butene

PubMed Central

2015-01-01

1,3-Butadiene (BD) is an environmental and occupational toxicant classified as a human carcinogen. It is oxidized by cytochrome P450 monooxygenases to 1,2-epoxy-3-butene (EB), which alkylates DNA. BD exposures lead to large numbers of mutations at A:T base pairs even though alkylation of guanines is more prevalent, suggesting that one or more adenine adducts of BD play a role in BD-mediated genotoxicity. However, the etiology of BD-mediated genotoxicity at adenine remains poorly understood. EB alkylates the N6 exocyclic nitrogen of adenine to form N6-(hydroxy-3-buten-1-yl)-2′-dA ((2S)-N6-HB-dA) adducts (TretyakovaN., LinY., SangaiahR., UptonP. B., and SwenbergJ. A. (1997) Carcinogenesis18, 137−1479054600). The structure of the (2S)-N6-HB-dA adduct has been determined in the 5′-d(C1G2G3A4C5Y6A7G8A9A10G11)-3′:5′-d(C12T13T14C15T16T17G18T19 C20C21G22)-3′ duplex [Y = (2S)-N6-HB-dA] containing codon 61 (underlined) of the human N-ras protooncogene, from NMR spectroscopy. The (2S)-N6-HB-dA adduct was positioned in the major groove, such that the butadiene moiety was oriented in the 3′ direction. At the Cα carbon, the methylene protons of the modified nucleobase Y6 faced the 5′ direction, which placed the Cβ carbon in the 3′ direction. The Cβ hydroxyl group faced toward the solvent, as did carbons Cγ and Cδ. The Cβ hydroxyl group did not form hydrogen bonds with either T16O4 or T17O4. The (2S)-N6-HB-dA nucleoside maintained the anti conformation about the glycosyl bond, and the modified base retained Watson–Crick base pairing with the complementary base (T17). The adduct perturbed stacking interactions at base pairs C5:G18, Y6:T17, and A7:T16 such that the Y6 base did not stack with its 5′ neighbor C5, but it did with its 3′ neighbor A7. The complementary thymine T17 stacked well with both 5′ and 3′ neighbors T16 and G18. The presence of the (2S)-N6-HB-dA resulted in a 5 °C reduction in the Tm of the duplex, which is attributed to less favorable stacking interactions and adduct accommodation in the major groove. PMID:25238403

Flow Analysis of Isobutane (R-600A) Inside AN Adiabatic Capillary Tube

NASA Astrophysics Data System (ADS)

Alok, Praveen; Sahu, Debjyoti

2018-02-01

Capillary tubes are simple narrow tubes but the phase change which occurs inside the capillary tubes is complex to analyze. In the present investigation, an attempt is made to analyze the flow of Isobutane (R-600a) inside the coiled capillary tubes for different load conditions by Homogeneous Equilibrium Model. The Length and diameter of the capillary tube not only depend on the pressure and temperature of the condenser and evaporator but also on the cooling load. The present paper investigates the change in dimensions of the coil capillary tube with respect to the change in cooling load on the system for the constant condenser and evaporator conditions. ANSYS CFX (Central Florida Expressway) software is used to study the flow characteristics of the refrigerant. Appropriate helical coil is selected for this analysis.

The toxicological properties of petroleum gases.

PubMed

McKee, Richard H; Herron, Deborah; Saperstein, Mark; Podhasky, Paula; Hoffman, Gary M; Roberts, Linda

2014-01-01

To characterize the toxicological hazards of petroleum gases, 90-day inhalation toxicity (Organization for Economic Cooperation and Development [OECD] 413) and developmental toxicity (OECD 414) tests were conducted with liquefied propane gas (LPG) at concentrations of 1000, 5000, or 10,000 ppm. A micronucleus test (OECD 474) of LPG was also conducted. No systemic or developmental effects were observed; the overall no observed adverse effect concentration (NOAEC) was 10,000 ppm. Further, there was no effect of LPG exposure at levels up to 10,000 ppm on micronucleus induction and no evidence of bone marrow toxicity. Other alkane gases (ethane, propane, n-butane, and isobutane) were then evaluated in combined repeated exposure studies with reproduction/development toxicity screening tests (OECD 422). There were no toxicologically important changes in parameters relating to systemic toxicity or neurotoxicity for any of these gases at concentrations ranging from 9000 to 16,000 ppm. There was no evidence of effects on developmental or reproductive toxicity in the studies of ethane, propane, or n-butane at the highest concentrations tested. However, there was a reduction in mating in the high-exposure group (9000 ppm) of the isobutane study, which although not significantly different was outside the range previously observed in the testing laboratory. Assuming the reduction in mating to have been toxicologically significant, the NOAEC for the isobutane reproductive toxicity screening test was 3000 ppm (7125 mg/m(3)). A method is proposed by which the toxicity of any of the 106 complex petroleum gas streams can be estimated from its composition.

Headspace Analysis of Ammonium Nitrate

DTIC Science & Technology

2017-01-25

to an Agilent 7890 gas chromatograph (GC) (Agilent Technologies, Santa Clara, CA). Methane CI was used to optimize instrument parameters, which...order of 0.1 mTorr, as were CF2Cl2, CF3Cl, methane , and isobutane. Figure 2. Analyte sorbent tube mounted and interfaced with a modified GC...observed at no more than 22% abundance of m/z 17. When larger gases such as methane were mixed in significant proportion with 500 ppm carbon

Kinetics and products of the OH radical-initiated reaction of 3-methyl-2-butenal.

PubMed

Tuazon, Ernesto C; Aschmann, Sara M; Nishino, Noriko; Arey, Janet; Atkinson, Roger

2005-06-07

Kinetics and products of the gas-phase reaction of OH radicals with 3-methyl-2-butenal [(CH3)2C=CHCHO] have been investigated at room temperature and atmospheric pressure of air. Using a relative rate method with methacrolein as the reference compound, a rate constant for the reaction of OH radicals with 3-methyl-2-butenal of (6.21 +/- 0.18) x 10(-11) cm3 molecule(-1) s(-1) at 296 +/- 2 K was measured, where the indicated error does not include the uncertainty in the rate constant for the methacrolein reference compound. Products of this reaction were investigated using in situ Fourier transform infrared (FT-IR) spectroscopy and solid phase microextraction (SPME) fibers coated with O-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine for on-fiber derivatization of carbonyl compounds, with subsequent thermal desorption and analysis by gas chromatography. The products observed and the molar formation yields were: glyoxal, 40 +/- 3%; acetone, 74 +/- 6%; 2-hydroxy-2-methylpropanal, 4.6 +/- 0.7%; CO2, 39% initially, decreasing to 30% at greater extents of reaction; peroxyacyl nitrate(s) [RC(O)OONO2], 5-8%, increasing with the extent of reaction and with the sum of the CO2 and RC(O)OONO2 yields being 38 +/- 6%; and organic nitrates [RONO2], 8.5 +/- 2.3%. The formation of these products is readily explained by a reaction mechanism based on those previously formulated for the corresponding reactions of the alpha,beta-unsaturated aldehydes acrolein, crotonaldehyde and methacrolein. Based on the mechanism proposed, at room temperature H-atom abstraction from the CHO group accounts for 40 +/- 6% of the overall reaction, and OH radical addition to the carbon atoms of the C=C bond accounts for 53 +/- 4% of the overall reaction. Hence 93 +/- 8% of the reaction products and pathways are accounted for.

A novel MVA-mediated pathway for isoprene production in engineered E. coli.

PubMed

Yang, Jianming; Nie, Qingjuan; Liu, Hui; Xian, Mo; Liu, Huizhou

2016-01-20

To deal with the increasingly severe energy crisis and environmental consequences, biofuels and biochemicals generated from renewable resources could serve as a promising alternative for replacing petroleum as a source of fuel and chemicals, among which isoprene (2-methyl-1,3-butadiene) in particular is of great significance in that it is an important platform chemical, which has been used in industrial production of synthetic rubber for tires and coatings or aviation fuel. We firstly introduced fatty acid decarboxylase (OleTJE) from Jeotgalicoccus species into E. coli to directly convert MVA(mevalonate) into 3-methy-3-buten-1-ol. And then to transform 3-methy-3-buten-1-ol to isoprene, oleate hydratase (OhyAEM) from Elizabethkingia meningoseptica was overexpressed in E. coli. A novel biosynthetic pathway of isoprene in E. coli was established by co-expressing the heterologous mvaE gene encoding acetyl-CoA acetyltransferase/HMG-CoA reductase and mvaS gene encoding HMG-CoA synthase from Enterococcus faecalis, fatty acid decarboxylase (OleTJE) and oleate hydratase (OhyAEM). Furthermore, to enhance isoprene production, a further optimization of expression level of OleTJE, OhyAEM was carried out by using different promoters and copy numbers of plasmids. Thereafter, the fermentation process was also optimized to improve the production of isoprene. The final engineered strain, YJM33, bearing the innovative biosynthetic pathway of isoprene, was found to produce isoprene up to 2.2 mg/L and 620 mg/L under flask and fed-batch fermentation conditions, respectively. In this study, by using metabolic engineering techniques, the novel MVA-mediated biosynthetic pathway of isoprene was successfully assembled in E. coli BL21(DE3) with the heterologous MVA upper pathway, OleTJE from Jeotgalicoccus species and OhyAEM from Elizabethkingia meningoseptica. Compared with traditional MVA pathway, the novel pathway is shortened by 3 steps. In addition, this is the first report on the reaction of converting MVA into 3-methy-3-buten-1-ol by fatty acid decarboxylase (OleTJE) from Jeotgalicoccus species. In brief, this study provided an alternative method for isoprene biosynthesis, which is largely different from the well-developed MEP pathway or MVA pathway.

Synthesis of Lipid Based Polyols from 1-butene Metathesized Palm Oil for Use in Polyurethane Foam Applications

NASA Astrophysics Data System (ADS)

Sasidharan Pillai, Prasanth Kumar

This thesis explores the use of 1-butene cross metathesized palm oil (PMTAG) as a feedstock for preparation of polyols which can be used to prepare rigid and flexible polyurethane foams. PMTAG is advantageous over its precursor feedstock, palm oil, for synthesizing polyols, especially for the preparation of rigid foams, because of the reduction of dangling chain effects associated with the omega unsaturated fatty acids. 1-butene cross metathesis results in shortening of the unsaturated fatty acid moieties, with approximately half of the unsaturated fatty acids assuming terminal double bonds. It was shown that the associated terminal OH groups introduced through epoxidation and hydroxylation result in rigid foams with a compressive strength approximately 2.5 times higher than that of rigid foams from palm and soybean oil polyols. Up to 1.5 times improvement in the compressive strength value of the rigid foams from the PMTAG polyol was further obtained following dry and/or solvent assisted fractionation of PMTAG in order to reduce the dangling chain effects associated with the saturated components of the PMTAG. Flexible foams with excellent recovery was achieved from the polyols of PMTAG and the high olein fraction of PMTAG indicating that these bio-derived polyurethane foams may be suitable for flexible foam applications. PMTAG polyols with controlled OH values prepared via an optimized green solvent free synthetic strategy provided flexible foams with lower compressive strength and higher recovery; i.e., better flexible foam potential compared to the PMTAG derived foams with non-controlled OH values. Overall, this study has revealed that the dangling chain issues of vegetable oils can be addressed in part using appropriate chemical and physical modification techniques such as cross metathesis and fractionation, respectively. In fact, the rigidity and the compressive strength of the polyurethane foams were in very close agreement with the percentage of terminal hydroxyl and OH value of the polyol. The results obtained from the study can be used to convert PMTAG like materials into industrially valuable materials.

Isotope Dilution nanoLC/ESI+-HRMS3 Quantitation of Urinary N7-(1-Hydroxy-3-buten-2-yl) Guanine Adducts in Humans and Their Use as Biomarkers of Exposure to 1,3-Butadiene.

PubMed

Sangaraju, Dewakar; Boldry, Emily J; Patel, Yesha M; Walker, Vernon; Stepanov, Irina; Stram, Daniel; Hatsukami, Dorothy; Tretyakova, Natalia

2017-02-20

1,3-Butadiene (BD) is an important industrial and environmental chemical classified as a known human carcinogen. Occupational exposure to BD in the polymer and monomer industries is associated with an increased incidence of lymphoma. BD is present in automobile exhaust, cigarette smoke, and forest fires, raising concern about potential exposure of the general population to this carcinogen. Following inhalation exposure, BD is bioactivated to 3,4-epoxy-1-butene (EB). If not detoxified, EB is capable of modifying guanine and adenine bases of DNA to form nucleobase adducts, which interfere with accurate DNA replication and cause cancer-initiating mutations. We have developed a nanoLC/ESI + -HRMS 3 methodology for N7-(1-hydroxy-3-buten-2-yl) guanine (EB-GII) adducts in human urine (limit of detection: 0.25 fmol/mL urine; limit of quantitation: 1.0 fmol/mL urine). This new method was successfully used to quantify EB-GII in urine of F344 rats treated with 0-200 ppm of BD, occupationally exposed workers, and smokers belonging to two different ethnic groups. EB-GII amounts increased in a dose-dependent manner in urine of laboratory rats exposed to 0, 62.5, or 200 ppm of BD. Urinary EB-GII levels were significantly increased in workers occupationally exposed to 0.1-2.2 ppm of BD (1.25 ± 0.51 pg/mg of creatinine) as compared to administrative controls exposed to <0.01 ppm of BD (0.22 ± 0.08 and pg/mg of creatinine) (p = 0.0024), validating the use of EB-GII as a biomarker of human exposure to BD. EB-GII was also detected in smokers' urine with European American smokers excreting significantly higher amounts of EB-GII than African American smokers (0.48 ± 0.09 vs 0.12 ± 0.02 pg/mg of creatinine, p = 3.1 × 10 -7 ). Interestingly, small amounts of EB-GII were observed in animals and humans with no known exposure to BD, providing preliminary evidence for its endogenous formation. Urinary EB-GII adduct levels and urinary mercapturic acids of BD (MHBMA, DHBMA) were compared in a genotyped multiethnic smoker cohort.

A Research-Based Undergraduate Organic Laboratory Project: Investigation of a One-Pot, Multicomponent, Environmentally Friendly Prins-Friedel-Crafts-Type Reaction

ERIC Educational Resources Information Center

Dintzner, Matthew R.; Maresh, Justin J.; Kinzie, Charles R.; Arena, Anthony F.; Speltz, Thomas

2012-01-01

Students in the undergraduate organic laboratory synthesize tetrahydro-2-(4-nitrophenyl)-4-phenyl-2"H"-pyran via the Montmorillonite K10 clay-catalyzed reaction of p-nitrobenzaldehye with methanol, 3-buten-1-ol, and benzene. The synthesis comprises an environmentally friendly tandem Prins-Friedel-Crafts-type multicomponent reaction (MCR) and sets…

40 CFR Appendix Xvii to Part 86 - Procedure for Determining Vehicle Emission Control Technology Category/Fuel Reactivity Adjustment...

Code of Federal Regulations, 2013 CFR

2013-07-01

...-1-pentene 4.42 00592-41-6 1-hexene 4.42 00110-54-3 n-hexane 0.98 13269-52-8 trans-3-hexene 6.69...” calculated for the i'th test vehicle. n = number of test vehicles. (ii) The 95 percent upper confidence bound...-methylpropene 5.31 00106-98-9 1-butene 8.91 00106-99-0 1,3-butadiene 10.89 00106-97-8 n-butane 1.02 00624-64-6...

40 CFR Appendix Xvii to Part 86 - Procedure for Determining Vehicle Emission Control Technology Category/Fuel Reactivity Adjustment...

Code of Federal Regulations, 2012 CFR

2012-07-01

...-1-pentene 4.42 00592-41-6 1-hexene 4.42 00110-54-3 n-hexane 0.98 13269-52-8 trans-3-hexene 6.69...” calculated for the i'th test vehicle. n = number of test vehicles. (ii) The 95 percent upper confidence bound...-methylpropene 5.31 00106-98-9 1-butene 8.91 00106-99-0 1,3-butadiene 10.89 00106-97-8 n-butane 1.02 00624-64-6...

1,2,4-Butanetriol: Analysis and Synthesis

DTIC Science & Technology

1982-12-08

also sought to lower the cost of 3-butene-l-ol by modification of the catalytic dehydration method commonly used to produce it from 1,3-butanediol. CH...monoepoxide of 1-methoxybutadiene, which on hydrolysis gives 3,4-dihydroxybutanal. This material can then be converted to BT by hydrogenation over Raney nickel...induce decomposition of reactive organics at elevated temperatures. The columns were usually heated in an oven from ’OQ0 to 300’% at 15%C per minute

Selective oxidation of alkanes and/or alkenes to valuable oxygenates

DOEpatents

Lin, Manhua; Pillai, Krishnan S.

2011-02-15

A catalyst, its method of preparation and its use for producing at least one of methacrolein and methacrylic acid, for example, by subjecting isobutane or isobutylene or a mixture thereof to a vapor phase catalytic oxidation in the presence of air or oxygen. In the case where isobutane alone is subjected to a vapor phase catalytic oxidation in the presence of air or oxygen, the product is at least one of isobutylene, methacrolein and methacrylic acid. The catalyst comprises a compound having the formula A.sub.aB.sub.bX.sub.xY.sub.yZ.sub.zO.sub.o wherein A is one or more elements selected from the group of Mo, W and Zr, B is one or more elements selected from the group of Bi, Sb, Se, and Te, X is one or more elements selected from the group of Al, Bi, Ca, Ce, Co, Fe, Ga, Mg, Ni, Nb, Sn, W and Zn, Y is one or more elements selected from the group of Ag, Au, B, Cr, Cs, Cu, K, La, Li, Mg, Mn, Na, Nb, Ni, P, Pb, Rb, Re, Ru, Sn, Te, Ti, V and Zr, and Z is one or more element from the X or Y groups or from the following: As, Ba, Pd, Pt, Sr, or mixtures thereof, and wherein a=1, 0.05

Condensation of nano-refrigerant inside a horizontal tube

NASA Astrophysics Data System (ADS)

Darzi, Milad; Sadoughi, M. K.; Sheikholeslami, M.

2018-05-01

In this paper, condensing pressure drop of refrigerant-based nanofluid inside a tube is studied. Isobutene was selected as the base fluid while CuO nanoparticles were utilized to prepare nano-refrigerant. However, for the feasibility of nanoparticle dispersion into the refrigerant, Polyester oil (POE) was utilized as lubricant oil and added to the pure refrigerant by 1% mass fraction. Various values of mass flux, vapor quality, concentration of nanoparticle are investigated. Results indicate that adding nanoparticles leads to enhance frictional pressure drop. Nanoparticles caused larger pressure drop penalty at relatively lower vapor qualities which may be attributed to the existing condensation flow pattern such that annular flow is less influenced by nanoparticles compared to intermittent flow regime.

Determination of thermodynamic properties of isotactic poly(1-butene) at infinite dilution using density and inverse gas chromatography.

PubMed

Kozłowska, Marta Karolina; Domańska, Urszula; Lempert, Małgorzata; Rogalski, Marek

2005-03-18

The partial molar volumes, V1(M), and the molar volume of isotactic crystalline low-molecular-weight poly(1-butene), iPBu-1, V1, have been calculated from the measured density of {iPBu-1 + solvent (n-hexane, n-heptane, n-nonane, n-decane, p-xylene, cyclohexane and chloroform)} systems. Some of the thermodynamic quantities were also obtained for the iPBu-1 with eight hydrocarbons (n-octane, n-decane, n-undecane, n-dodecane, n-tridecane, o-xylene, m-xylene, p-xylene) by the method of inverse gas chromatography at various temperatures. The weight fraction activity coefficients of the solvent at infinite dilution, omega2(infinity) and the Flory-Huggins thermodynamic interaction parameters, chi21(infinity), between polymer and solvents were determined. The partial molar free energy, deltaG2(infinity), the partial molar heat of mixing, deltaH2(infinity), at infinite dilution and the polymer solubility parameter, delta1, were calculated. Additionally, the (solid + liquid) binary mixtures equilibria, SLE, of iPBu-1 with three hydrocarbons (n-octane, n-decane and m-xylene) were studied by a dynamic method. By performing these experiments over a large concentration range, the T-x phase diagrams of the polymer-solvent systems were constructed. The excess Gibbs energy models were used to describe the nonideal behaviour of the liquid phase. The omega2(infinity) were determined from the solubility measurements and were predicted by using the UNIFAC FV model.

Crystalline mesoporous zirconia catalysts having stable tetragonal pore wall structure

DOEpatents

Sachtler, W.M.H.; Huang, Y.Y.

1998-07-28

Methods are disclosed for the preparation of new sulfated mesoporous zirconia materials/catalysts with crystalline pore walls of predominantly tetragonal crystal structure, characterized by nitrogen physical sorption measurement, X-ray diffraction, transmission electron microscopy and catalytic tests using n-butane isomerization to iso-butane and alkylation of 1-naphthol with 4-tert-butylstyrene as probe reactions. Sulfate deposition is preferred for the transformation of a mesoporous precursor with amorphous pore walls into a material with crystalline pore walls maintaining the mesoporous characteristics. 17 figs.

Crystalline mesoporous zirconia catalysts having stable tetragonal pore wall structure

DOEpatents

Sachtler, Wolfgang M. H.; Huang, Yin-Yan

1998-01-01

Methods for the preparation of new sulfated mesoporous zirconia materials/catalysts with crystalline pore walls of predominantly tetragonal crystal structure, characterized by nitrogen physisorption measurement, X-ray diffraction, transmission electron microscopy and catalytic tests using n-butane isomerization to iso-butane and alkylation of 1-naphthol with 4-tert-butylstyrene as probe reactions. Sulfate deposition is preferred for the transformation of a mesoporous precursor with amorphous pore walls into a material with crystalline pore walls maintaining the mesoporous characteristics.

Preliminary Work for Identifying and Tracking Combustion Reaction Pathways by Coherent Microwave Mapping of Photoelectrons

DTIC Science & Technology

2016-06-24

wall Radar technique has been built and preliminary results of pyrolysis of iso-butane have been obtained. Qualitative measurements of ethylene in...The (2+1) REMPI ionizations of ethylene (C2H4, 11B3u(π,3p) Rydberg manifold) was selectively induced at 310─325nm. The ethylene was detectable at...quantitative measurements of ethylene as one of the pyrolysis products by using coherent microwave Rayleigh scattering (Radar) from Resonant Enhanced Multi

Composite Materials with Improved Properties in Compression: Synthesis of 3-Methylene-1,1-Dichlorosilacyclobutane and 1,1-Dichlorosilacyclopent-3-ene

DTIC Science & Technology

1990-05-09

reagents may in fact be involved. Of synthetic interest, V undergoes intramolecular Grignard ring closure to yield III (10%). While the yield of III is low...VII) as the major product along with 1,4-bis(trichlorosilyl)- cis-2-butene (VIII). VII undergoes cyclization by an intramolec- ular Grignard ring...addition of methyl Grignard to III. The 1H 8 am NMR chemical shifts of I in diethyl ether are consistently about 0.4 ppm downfield from those previously

Canopy Level Emissions of 2-methyl-3-buten-2-ol ...

EPA Pesticide Factsheets

Emissions of biogenic volatile organic compounds (BVOC) observed during 2007 from a Pinus taeda experimental plantation in Central North Carolina are compared with model estimates from MEGAN 2.1. Relaxed Eddy Accumulation (REA) estimates of 2-methyl-3-buten-2-ol (MBO) fluxes are a factor of 3-4 higher than model estimates. MEGAN2.1 monoterpene emission estimates were approximately a factor of two higher than REA flux measurements. MEGAN2.1 β-caryophyllene emission estimates were within 60% of growing season REA flux estimates, but were several times higher than REA fluxes during cooler, dormant season periods. The sum of other sesquiterpene emissions estimated by MEGAN2.1 was several times higher than REA estimates throughout the year. Model components are examined to understand these discrepancies. Summertime LAI (and therefore foliar biomass) is a factor of two higher than assumed in MEGAN for the Pinus taeda default. Increasing the canopy mean MBO emission factor from 0.35 to 1.0 mg m-2 hr-1 also reduces MEGAN2.1 vs flux differences. This increase is within current emission factor uncertainties. The algorithm within MEGAN which adjusts isoprene emission estimates as a function of the previous 24 hour’s temperatures and light seems to also improve seasonal MEGAN MBO correlation with REA fluxes. Including the effects of the previous 240 hours, however, seems to degrade temporal model correlation with fluxes. This paper describes an emission inventory and mod

Grubbs's Cross Metathesis of Eugenol with cis-2-butene-1, 4-diol to Make a Natural Product: An Organometallic Experiment for the Undergraduate Lab

ERIC Educational Resources Information Center

Taber, Douglass F.; Frankowski, Kevin J.

2006-01-01

A modified experimental procedure for the one-step synthesis that is suitable for the undergraduate organic lab is presented. In the course of work towards the more routine use of air-sensitive organometallic complexes such as the Grubb's catalyst, the natural product (E)-4-(4-hydroxy-3-methoxyphenyl) but-2-en-ol, 4, was synthesized.

Identification of volatile and semivolatile compounds in chemical ionization GC-MS using a mass-to-structure (MTS) Search Engine with integral isotope pattern ranking.

PubMed

Liao, Wenta; Draper, William M

2013-02-21

The mass-to-structure or MTS Search Engine is an Access 2010 database containing theoretical molecular mass information for 19,438 compounds assembled from common sources such as the Merck Index, pesticide and pharmaceutical compilations, and chemical catalogues. This database, which contains no experimental mass spectral data, was developed as an aid to identification of compounds in atmospheric pressure ionization (API)-LC-MS. This paper describes a powerful upgrade to this database, a fully integrated utility for filtering or ranking candidates based on isotope ratios and patterns. The new MTS Search Engine is applied here to the identification of volatile and semivolatile compounds including pesticides, nitrosoamines and other pollutants. Methane and isobutane chemical ionization (CI) GC-MS spectra were obtained from unit mass resolution mass spectrometers to determine MH(+) masses and isotope ratios. Isotopes were measured accurately with errors of <4% and <6%, respectively, for A + 1 and A + 2 peaks. Deconvolution of interfering isotope clusters (e.g., M(+) and [M - H](+)) was required for accurate determination of the A + 1 isotope in halogenated compounds. Integrating the isotope data greatly improved the speed and accuracy of the database identifications. The database accurately identified unknowns from isobutane CI spectra in 100% of cases where as many as 40 candidates satisfied the mass tolerance. The paper describes the development and basic operation of the new MTS Search Engine and details performance testing with over 50 model compounds.

Influence of organic load rate (OLR) on the hydrolytic acidification of 2-butenal manufacture wastewater and analysis of bacterial community structure.

PubMed

Song, Guangqing; Xi, Hongbo; Zhou, Yuexi; Fu, Liya; Xing, Xin; Wu, Changyong

2017-11-01

The influence of organic loading rate (OLR) on the performance of hydrolytic acidification process for treating 2-butenal manufacture wastewater was comprehensively studied, while its impact on microbial community was thoroughly investigated. The results demonstrated that over 21.0% of the average COD removal rate was observed in the range of OLR from 0.52 to 3.98g COD/L·d, whereas it reduced to 15.3% with increasing OLR to 6.09g COD/L·d. The acidification degree dramatically decreased from 17.1% to 4.7% when OLR increased from 3.98 to 6.09g COD/L·d. In addition, the removal rates of three kinds of typical matters were less than 65% at the OLR 6.09g COD/L·d. Illumina MiSeq sequencing revealed that Proteobacteria, Chloroflexi, Firmicutes, and Bacteroidetes were dominant phyla at different OLRs. Finally, multivariate analysis suggested that the genera Longilinea and T78 had a positive correlation with the degradation of three kinds of typical matters and COD removal rates. Copyright © 2017 Elsevier Ltd. All rights reserved.

Protective Effect of 4-(3,4-Dihydroxyphenyl)-3-Buten-2-One from Phellinus linteus on Naproxen-Induced Gastric Antral Ulcers in Rats.

PubMed

Kim, Jeong-Hwan; Kwon, Hyun Ju; Kim, Byung Woo

2016-05-28

The present study investigated the protective effect of naturally purified 4-(3,4- dihydroxyphenyl)-3-buten-2-one (DHP) from Phellinus linteus against naproxen-induced gastric antral ulcers in rats. To verify the protective effect of DHP on naproxen-induced gastric antral ulcers, various doses (1, 5, and 10 μg/kg) of DHP were pretreated for 3 days, and then gastric damage was caused by 80 mg/kg naproxen applied for 3 days. DHP prevented naproxen-induced gastric antral ulcers in a dose-dependent manner. In particular, 10 μg/kg DHP showed the best protective effect against naproxen-induced gastric antral ulcers. Moreover, DHP significantly attenuated the naproxen-induced lipid peroxide level in gastric mucosa and increased the activities of radical scavenging enzymes, such as superoxide dismutase, catalase, and glutathione peroxidase, in a dose-dependent manner. A histological examination clearly demonstrated that the gastric antral ulcer induced by naproxen nearly disappeared after the pretreatment of DHP. These results suggest that DHP can inhibit naproxen-induced gastric antral ulcers through prevention of lipid peroxidation and activation of radical scavenging enzymes.

Formation of Fused-Ring 2′-Deoxycytidine Adducts from 1-Chloro-3-buten-2-one, an in Vitro 1,3-Butadiene Metabolite, under in Vitro Physiological Conditions

PubMed Central

Sun, Liang; Pelah, Avishay; Zhang, Dong-Ping; Zhong, Yu-Fang; An, Jing; Yu, Ying-Xin; Zhang, Xin-Yu; Elfarra, Adnan A.

2013-01-01

1-Chloro-3-buten-2-one (CBO) is a potential metabolite of 1,3-butadiene (BD), a carcinogenic air pollutant. CBO is a bifunctional alkylating agent that readily reacts with glutathione (GSH) to form mono-GSH and di-GSH adducts. Recently, CBO and its precursor 1-chloro-2-hydroxy-3-butene (CHB) were found to be cytotoxic and genotoxic in human liver cells in culture with CBO being approximately 100-fold more potent than CHB. In the present study, CBO was shown to react readily with 2′-deoxycytidine (dC) under in vitro physiological conditions (pH 7.4, 37 °C) to form four dC adducts with the CBO moieties forming fused rings with the N3 and N4 atoms of dC. The four products were structurally characterized as 2-hydroxy-2-hydroxymethyl-7-(2-deoxy-β-D-erythro-pentofuranosyl)-1,2,3,4-tetrahy dro-6-oxo-6H,7H-pyrimido[1,6-a]pyrimidin-5-ium (dC-1 and dC-2, a pair of diastereomers), 4-chloromethyl-4-hydroxy-7-(2-deoxy-β-D-erythro-pentofuranosyl)-1,2,3,4-tetrahydr o-6-oxo-6H,7H-pyrimido[1,6-a]pyrimidin-5-ium (dC-3), and 2-chloromethyl-2-hydroxy-7-(2-deoxy-β-D-erythro-pentofuranosyl)-1,2,3,4-tetrahydr o-6-oxo-6H,7H-pyrimido[1,6-a]pyrimidin-5-ium (dC-4). Interestingly, dC-1 and dC-2 were stable under our experimental conditions (pH 7.4, 37 °C, 6 h) and existed in equilibrium as indicated by HPLC analysis, whereas dC-3 and dC-4 were labile with the half-lives being 3.0 ± 0.36 and 1.7 ± 0.06 h, respectively. Decomposition of dC-4 produced both dC-1 and dC-2, whereas acid hydrolysis of dC-1/dC-2 and dC-4 in 1 M HCl at 100 °C for 30 min yielded the deribosylated adducts dC-1H/dC-2H and dC-4H, respectively. Because fused-ring dC adducts of other chemicals are mutagenic, the characterized CBO-dC adducts could be mutagenic and play a role in the cytotoxicity and genotoxicity of CBO and its precursors, CHB and BD. The CBO-dC adducts may also be used as standards to characterize CBO-DNA adducts and to develop potential biomarkers for CBO formation in vivo. PMID:24020501

21 CFR 184.1165 - n-Butane and iso-butane.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., flammable gases at normal temperatures and pressures. They are easily liquefied under pressure at room... fractionation following absorption in oil, adsorption to surface-active agents, or refrigeration. (b) The... used as propellants, aerating agents, and gases as defined in § 170.3(o)(25) of this chapter. (2) The...

21 CFR 184.1165 - n-Butane and iso-butane.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., flammable gases at normal temperatures and pressures. They are easily liquefied under pressure at room... fractionation following absorption in oil, adsorption to surface-active agents, or refrigeration. (b) The... used as propellants, aerating agents, and gases as defined in § 170.3(o)(25) of this chapter. (2) The...

76 FR 5687 - Isobutane; Exemption From the Requirement of a Tolerance

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-02

....'' This includes exposure through drinking water and in residential settings, but does not include... the inert ingredient through food, drinking water, and through other exposures that occur as a result... Assessment No hazard was identified for the acute and chronic dietary assessment (food and drinking water...

40 CFR 98.406 - Data reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.406 Data..., isobutane, and pentanes plus. (3) Annual volumes in Mscf of natural gas received for processing. (4) Annual... Mscf of natural gas received by the LDC at its city gate stations for redelivery on the LDC's...

40 CFR 98.406 - Data reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.406 Data..., isobutane, and pentanes plus. (3) Annual volumes in Mscf of natural gas received for processing. (4) Annual... Mscf of natural gas received by the LDC at its city gate stations for redelivery on the LDC's...

40 CFR 98.406 - Data reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.406 Data..., isobutane, and pentanes plus. (3) Annual volumes in Mscf of natural gas received for processing. (4) Annual... Mscf of natural gas received by the LDC at its city gate stations for redelivery on the LDC's...

Open Burn/Open Detonation Dispersion Model (OBODM) User’s Guide. Volume I. User’s Instructions

DTIC Science & Technology

1998-02-01

Fuel/Expl6sives Data Base File OBODFUEL.OBD ...... 51 4.9 SIGMAPLOT File Format and Contents ...... .............. .. 106 4.10 Grid Coordinates and...135.2 0.9391 0 2.95E-07 trans-2-Butene 125.0 1.1830 0 1.97E-07 Propellant, PBXN -110 1000 0 44 1,2,4-Trimethylbenzene 120.2 0.8758 0 4.25E-07 1,2,4...Calculation height, if applicable 106 The solution data follow and depend on the output options selected. The following record group is written only if N

Direct observation of OH production from the ozonolysis of olefins

NASA Astrophysics Data System (ADS)

Donahue, Neil M.; Kroll, Jesse H.; Anderson, James G.; Demerjian, Kenneth L.

Ozone olefin reactions may be a significant source of OH in the urban atmosphere, but current evidence for OH production is indirect and contested. We report the first direct observation of OH radicals from the reaction of ozone with a series of olefins (ethene, isoprene, trans-2-butene and 2,3 dimethyl-2-butene) in 4-6 torr of nitrogen. Using LIF to directly observe the steady-state of OH produced by the initial ozone-olefin reaction and subsequently destroyed by the OH-olefin reaction, we are able to establish OH yields broadly consistent with indirect values. The identification of the OH is unequivocal, and there is no indication that it is produced by a secondary process. To support these observations, we present a complete ab-initio potential energy surface for the O3-ethene reaction, extending from the reactants to available products.

Survival of aerosolized bacteriophage phi X174 in air containing ozone--olefin mixtures.

PubMed Central

Mik, G.; de Groot, I.; Gerbrandy, J. L.

1977-01-01

The effects of ozone and ozonized olefins on aerosol survival of bacteriophage phiX174 were studied. The ozone concentrations used were between 0 and 110 parts/10(9), giving decay rates up to 0-03 min-1. The olefins used were trans-2-butene and cyclohexene in concentrations of 500 parts/10(9) and 2-4 parts/10(6), respectively. Olefins alone have no effect, whereas in combination with ozone, decay rates of 0-1 min-1 and higher were obtained. The results are discussed in relation to the viricidal effect of open air. PMID:265341

Catalytic oxidation of light alkanes in presence of a base

DOEpatents

Bhinde, Manoj V.; Bierl, Thomas W.

1998-01-01

The presence of a base in the reaction mixture in a metal-ligand catalyzed partial oxidation of alkanes results in sustained catalyst activity, and in greater percent conversion as compared with oxidation in the absence of base, while maintaining satisfactory selectivity for the desired oxidation, for example the oxidation of isobutane to isobutanol.

Mid-infrared surface transmitting and detecting quantum cascade device for gas-sensing

PubMed Central

Harrer, Andreas; Szedlak, Rolf; Schwarz, Benedikt; Moser, Harald; Zederbauer, Tobias; MacFarland, Donald; Detz, Hermann; Andrews, Aaron Maxwell; Schrenk, Werner; Lendl, Bernhard; Strasser, Gottfried

2016-01-01

We present a bi-functional surface emitting and surface detecting mid-infrared device applicable for gas-sensing. A distributed feedback ring quantum cascade laser is monolithically integrated with a detector structured from a bi-functional material for same frequency lasing and detection. The emitted single mode radiation is collimated, back reflected by a flat mirror and detected by the detector element of the sensor. The surface operation mode combined with the low divergence emission of the ring quantum cascade laser enables for long analyte interaction regions spatially separated from the sample surface. The device enables for sensing of gaseous analytes which requires a relatively long interaction region. Our design is suitable for 2D array integration with multiple emission and detection frequencies. Proof of principle measurements with isobutane (2-methylpropane) and propane as gaseous analytes were conducted. Detectable concentration values of 0–70% for propane and 0–90% for isobutane were reached at a laser operation wavelength of 6.5 μm utilizing a 10 cm gas cell in double pass configuration. PMID:26887891

Encyclopedia of Explosives and Related Items. Volume 7. H2 to Lysol

DTIC Science & Technology

1975-01-01

68. (21) 2.75 0 15 C3H7CI I1- Chloropropane -31.10 699 55.0 (21) 2.98 0 16 C3H Propane -24.82 626 63.3 (21) 2.48 0 17 C4H8 1 .Butene -0.03 825 59.1 ( 1 ...Information Service (formerly Clearinghouse) US Department of Commerce Springfield, Virginia 22151 1 -800-553-6847 USA only 703-605-6000 www.ntis.gov/FCPC...in Volume 1 in order to understand the authors’ way of presenting the subject matter In preparation for and during the writing of this Encyclopedia

Exchange Reactions of Organotin and Organosilicon Compounds with Mild Fluorinating Agents

DTIC Science & Technology

1992-03-01

methylphosphonic difluoride, boron trifluoride etherate, and perfluoroisobutene all react with both organosilicon and organotin. alkoxides to give...inlet tube, was charged with tributyltin cyanide (53.30 gm, 0.1686 mol) in a dry glove bag under an inert atmosphere and 500 ml of dry xylene was then...Chem. Vol. 29, p 471 (1985). 6. Tyuleneva, V.V., Rozov, L.A., Zeifman, Yu.V. and I. L. Knuny- ants,"Exchange of Fluorine by Chlorine in Perfluoro-isobutene," Tzv.Akad.Nauk. SSSR. Ser. Khim No. 5, p 1136 (1975). 17

Emission of 2-methyl-3-buten-2-ol by pines: A potentially large natural source of reactive carbon to the atmosphere

NASA Astrophysics Data System (ADS)

Harley, Peter; Fridd-Stroud, Verity; Greenberg, James; Guenther, Alex; Vasconcellos, PéRola

1998-10-01

High rates of emission of 2-methyl-3-buten-2-ol (MBO) were measured from needles of several pine species. Emissions of MBO in the light were 1 to 2 orders of magnitude higher than emissions of monoterpenes and, in contrast to monoterpene emissions from pines, were absent in the dark. MBO emissions were strongly dependent on incident light, behaving similarly to net photosynthesis. Emission rates of MBO increased exponentially with temperature up to approximately 35°C. Above approximately 42°C, emission rates declined rapidly. Emissions could be modeled using existing algorithms for isoprene emission. We propose that emissions of MBO from lodgepole and ponderosa pine are the primary source of high concentrations of this compound, averaging 1-3 ppbv, found in ambient air samples collected in Colorado at an isolated mountain site approximately 3050 m above sea level. Subsequent field studies in a ponderosa pine plantation in California confirmed high MBO emissions, which averaged 25 μg C g-1 h-1 for 1-year-old needles, corrected to 30°C and photon flux of 1000 μmol m-2 s-1. A total of 34 pine species growing at Eddy Arboretum in Placerville, California, were investigated, of which 11 exhibited high emissions of MBO (>5 μg C g-1 h-1), and 6 emitted small but detectable amounts. All the emitting species are of North American origin, and most are restricted to western North America. These results indicate that MBO emissions from pines may constitute a significant source of reactive carbon and a significant source of acetone, to the atmosphere, particularly in the western United States.

Trapping of cis-2-butene-1,4-dial to measure furan metabolism in human liver microsomes by cytochrome P450 enzymes.

PubMed

Gates, Leah A; Lu, Ding; Peterson, Lisa A

2012-03-01

Furan is a liver toxicant and carcinogen in rodents. It is classified as a possible human carcinogen, but the human health effects of furan exposure remain unknown. The oxidation of furan by cytochrome P450 (P450) enzymes is necessary for furan toxicity. The product of this reaction is the reactive α,β-unsaturated dialdehyde, cis-2-butene-1,4-dial (BDA). To determine whether human liver microsomes metabolize furan to BDA, a liquid chromatography/tandem mass spectrometry method was developed to detect and quantify BDA by trapping this reactive metabolite with N-acetyl-l-cysteine (NAC) and N-acetyl-l-lysine (NAL). Reaction of NAC and NAL with BDA generates N-acetyl-S-[1-(5-acetylamino-5-carboxypentyl)-1H-pyrrol-3-yl]-l-cysteine (NAC-BDA-NAL). Formation of NAC-BDA-NAL was quantified in 21 different human liver microsomal preparations. The levels of metabolism were comparable to that observed in F-344 rat and B6C3F1 mouse liver microsomes, two species known to be sensitive to furan-induced toxicity. Studies with recombinant human liver P450s indicated that CYP2E1 is the most active human liver furan oxidase. The activity of CYP2E1 as measured by p-nitrophenol hydroxylase activity was correlated to the extent of NAC-BDA-NAL formation in human liver microsomes. The formation of NAC-BDA-NAL was blocked by CYP2E1 inhibitors but not other P450 inhibitors. These results suggest that humans are capable of oxidizing furan to its toxic metabolite, BDA, at rates comparable to those of species sensitive to furan exposure. Therefore, humans may be susceptible to furan's toxic effects.

Trapping of cis-2-Butene-1,4-dial to Measure Furan Metabolism in Human Liver Microsomes by Cytochrome P450 Enzymes

PubMed Central

Gates, Leah A.; Lu, Ding

2012-01-01

Furan is a liver toxicant and carcinogen in rodents. It is classified as a possible human carcinogen, but the human health effects of furan exposure remain unknown. The oxidation of furan by cytochrome P450 (P450) enzymes is necessary for furan toxicity. The product of this reaction is the reactive α,β-unsaturated dialdehyde, cis-2-butene-1,4-dial (BDA). To determine whether human liver microsomes metabolize furan to BDA, a liquid chromatography/tandem mass spectrometry method was developed to detect and quantify BDA by trapping this reactive metabolite with N-acetyl-l-cysteine (NAC) and N-acetyl-l-lysine (NAL). Reaction of NAC and NAL with BDA generates N-acetyl-S-[1-(5-acetylamino-5-carboxypentyl)-1H-pyrrol-3-yl]-l-cysteine (NAC-BDA-NAL). Formation of NAC-BDA-NAL was quantified in 21 different human liver microsomal preparations. The levels of metabolism were comparable to that observed in F-344 rat and B6C3F1 mouse liver microsomes, two species known to be sensitive to furan-induced toxicity. Studies with recombinant human liver P450s indicated that CYP2E1 is the most active human liver furan oxidase. The activity of CYP2E1 as measured by p-nitrophenol hydroxylase activity was correlated to the extent of NAC-BDA-NAL formation in human liver microsomes. The formation of NAC-BDA-NAL was blocked by CYP2E1 inhibitors but not other P450 inhibitors. These results suggest that humans are capable of oxidizing furan to its toxic metabolite, BDA, at rates comparable to those of species sensitive to furan exposure. Therefore, humans may be susceptible to furan's toxic effects. PMID:22187484

Diffusion in confinement: kinetic simulations of self- and collective diffusion behavior of adsorbed gases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abouelnasr, MKF; Smit, B

2012-01-01

The self- and collective-diffusion behaviors of adsorbed methane, helium, and isobutane in zeolite frameworks LTA, MFI, AFI, and SAS were examined at various concentrations using a range of molecular simulation techniques including Molecular Dynamics (MD), Monte Carlo (MC), Bennett-Chandler (BC), and kinetic Monte Carlo (kMC). This paper has three main results. (1) A novel model for the process of adsorbate movement between two large cages was created, allowing the formulation of a mixing rule for the re-crossing coefficient between two cages of unequal loading. The predictions from this mixing rule were found to agree quantitatively with explicit simulations. (2) Amore » new approach to the dynamically corrected Transition State Theory method to analytically calculate self-diffusion properties was developed, explicitly accounting for nanoscale fluctuations in concentration. This approach was demonstrated to quantitatively agree with previous methods, but is uniquely suited to be adapted to a kMC simulation that can simulate the collective-diffusion behavior. (3) While at low and moderate loadings the self- and collective-diffusion behaviors in LTA are observed to coincide, at higher concentrations they diverge. A change in the adsorbate packing scheme was shown to cause this divergence, a trait which is replicated in a kMC simulation that explicitly models this behavior. These phenomena were further investigated for isobutane in zeolite MFI, where MD results showed a separation in self- and collective-diffusion behavior that was reproduced with kMC simulations.« less

Environmental and Economic Assessment of Electrothermal Swing Adsorption of Air Emissions from Sheet-Foam Production Compared to Conventional Abatement Techniques.

PubMed

Johnsen, David L; Emamipour, Hamidreza; Guest, Jeremy S; Rood, Mark J

2016-02-02

A life-cycle assessment (LCA) and cost analysis are presented comparing the environmental and economic impacts of using regenerative thermal oxidizer (RTO), granular activated carbon (GAC), and activated carbon fiber cloth (ACFC) systems to treat gaseous emissions from sheet-foam production. The ACFC system has the lowest operational energy consumption (i.e., 19.2, 8.7, and 3.4 TJ/year at a full-scale facility for RTO, GAC, and ACFC systems, respectively). The GAC system has the smallest environmental impacts across most impact categories for the use of electricity from select states in the United States that produce sheet foam. Monte Carlo simulations indicate the GAC and ACFC systems perform similarly (within one standard deviation) for seven of nine environmental impact categories considered and have lower impacts than the RTO for every category for the use of natural gas to produce electricity. The GAC and ACFC systems recover adequate isobutane to pay for themselves through chemical-consumption offsets, whereas the net present value of the RTO is $4.1 M (20 years, $0.001/m(3) treated). The adsorption systems are more environmentally and economically competitive than the RTO due to recovered isobutane for the production process and are recommended for resource recovery from (and treatment of) sheet-foam-production exhaust gas. Research targets for these adsorption systems should focus on increasing adsorptive capacity and saturation of GAC systems and decreasing electricity and N2 consumption of ACFC systems.

Diffusion in confinement: kinetic simulations of self- and collective diffusion behavior of adsorbed gases.

PubMed

Abouelnasr, Mahmoud K F; Smit, Berend

2012-09-07

The self- and collective-diffusion behaviors of adsorbed methane, helium, and isobutane in zeolite frameworks LTA, MFI, AFI, and SAS were examined at various concentrations using a range of molecular simulation techniques including Molecular Dynamics (MD), Monte Carlo (MC), Bennett-Chandler (BC), and kinetic Monte Carlo (kMC). This paper has three main results. (1) A novel model for the process of adsorbate movement between two large cages was created, allowing the formulation of a mixing rule for the re-crossing coefficient between two cages of unequal loading. The predictions from this mixing rule were found to agree quantitatively with explicit simulations. (2) A new approach to the dynamically corrected Transition State Theory method to analytically calculate self-diffusion properties was developed, explicitly accounting for nanoscale fluctuations in concentration. This approach was demonstrated to quantitatively agree with previous methods, but is uniquely suited to be adapted to a kMC simulation that can simulate the collective-diffusion behavior. (3) While at low and moderate loadings the self- and collective-diffusion behaviors in LTA are observed to coincide, at higher concentrations they diverge. A change in the adsorbate packing scheme was shown to cause this divergence, a trait which is replicated in a kMC simulation that explicitly models this behavior. These phenomena were further investigated for isobutane in zeolite MFI, where MD results showed a separation in self- and collective- diffusion behavior that was reproduced with kMC simulations.

Protection of rats against 3-butene-1,2-diol-induced hepatotoxicity and hypoglycemia by N-acetyl-L-cysteine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sprague, Christopher L.; Elfarra, Adnan A.

2005-09-15

3-Butene-1,2-diol (BDD), an allylic alcohol and major metabolite of 1,3-butadiene, has previously been shown to cause hepatotoxicity and hypoglycemia in male Sprague-Dawley rats, but the mechanisms of toxicity were unclear. In this study, rats were administered BDD (250 mg/kg) or saline, ip, and serum insulin levels, hepatic lactate levels, and hepatic cellular and mitochondrial GSH, GSSG, ATP, and ADP levels were measured 1 or 4 h after treatment. The results show that serum insulin levels were not causing the hypoglycemia and that the hypoglycemia was not caused by an enhancement of the metabolism of pyruvate to lactate because hepatic lactatemore » levels were either similar (1 h) or lower (4 h) than controls. However, both hepatic cellular and mitochondrial GSH and GSSG levels were severely depleted 1 and 4 h after treatment and the mitochondrial ATP/ADP ratio was also lowered 4 h after treatment relative to controls. Because these results suggested a role for hepatic cellular and mitochondrial GSH in BDD toxicity, additional rats were administered N-acetyl-L-cysteine (NAC; 200 mg/kg) 15 min after BDD administration. NAC treatment partially prevented depletion of hepatic cellular and mitochondrial GSH and preserved the mitochondrial ATP/ADP ratio. NAC also prevented the severe depletion of serum glucose concentration and the elevation of serum alanine aminotransferase activity after BDD treatment without affecting the plasma concentration of BDD. Thus, depletion of hepatic cellular and mitochondrial GSH followed by the decrease in the mitochondrial ATP/ADP ratio was likely contributing to the mechanisms of hepatotoxicity and hypoglycemia in the rat.« less

Volatile organic compounds in a residential and commercial urban area with a diesel, compressed natural gas and oxygenated gasoline vehicular fleet.

PubMed

Martins, Eduardo Monteiro; Arbilla, Graciela; Gatti, Luciana Vanni

2010-02-01

Air samples were collected in a typical residential and commercial area in Rio de Janeiro, Brazil, where buses and trucks use diesel and light duty vehicles use compressed natural gas, ethanol, and gasohol (gasoline blended with ethanol) as fuel. A total of 66 C3-C12 volatile organic compounds (VOCs) were identified. The most abundant compounds, on a mass concentration basis, included propane, isobutane, i-pentane, m,p-xylene, 1,3,5-trimethylbenzene, toluene, styrene, ethylbenzene, isopropylbenzene, o-xylene and 1,2,4-trimethylbenzene. Two VOCs photochemical reactivity rankings are presented: one involves reaction with OH and the other involves production of ozone.

Directional Dark Matter Detector Prototype (Time Projection Chamber)

NASA Astrophysics Data System (ADS)

Oliver-Mallory, Kelsey; Garcia-Sciveres, Maurice; Kadyk, John; Lopex-Thibodeaux, Mayra

2013-04-01

The time projection chamber is a mature technology that has emerged as a promising candidate for the directional detection of the WIMP particle. In order to utilize this technology in WIMP detection, the operational parameters must be chosen in the non-ideal regime. A prototype WIMP detector with a 10cm field cage, double GEM amplification, and ATLAS FEI3 pixel chip readout was constructed for the purpose of investigating effects of varying gas pressure in different gas mixtures. The rms radii of ionization clusters of photoelectrons caused by X-rays from a Fe-55 source were measured for several gas pressures between 760torr and 99torr in Ar(70)/ CO2(30), CF4, He(80)/Isobutane(20), and He(80)/CF4(20) mixtures. Average radii were determined from distributions of the data for each gas mixture and pressure, and revealed a negative correlation between pressure and radius in Ar(70)/CO2(30) and He(80)/Isobutane(20) mixtures. Investigation of the pressure-radius measurements are in progress using distributions of photoelectron and auger electron practical ranges (Univ. of Pisa) and diffusion, using the Garfield Monte Carlo program.

Control of electrothermal heating during regeneration of activated carbon fiber cloth.

PubMed

Johnsen, David L; Mallouk, Kaitlin E; Rood, Mark J

2011-01-15

Electrothermal swing adsorption (ESA) of organic gases generated by industrial processes can reduce atmospheric emissions and allow for reuse of recovered product. Desorption energy efficiency can be improved through control of adsorbent heating, allowing for cost-effective separation and concentration of these gases for reuse. ESA experiments with an air stream containing 2000 ppm(v) isobutane and activated carbon fiber cloth (ACFC) were performed to evaluate regeneration energy consumption. Control logic based on temperature feedback achieved select temperature and power profiles during regeneration cycles while maintaining the ACFC's mean regeneration temperature (200 °C). Energy requirements for regeneration were independent of differences in temperature/power oscillations (1186-1237 kJ/mol of isobutane). ACFC was also heated to a ramped set-point, and the average absolute error between the actual and set-point temperatures was small (0.73%), demonstrating stable control as set-point temperatures vary, which is necessary for practical applications (e.g., higher temperatures for higher boiling point gases). Additional logic that increased the maximum power application at lower ACFC temperatures resulted in a 36% decrease in energy consumption. Implementing such control logic improves energy efficiency for separating and concentrating organic gases for post-desorption liquefaction of the organic gas for reuse.

Theoretical investigation of the oxidation pathways of the Cl-initiated reaction of 2-methyl-3-buten-2-ol

NASA Astrophysics Data System (ADS)

Zhang, Weichao; Zhang, Dongju

2012-12-01

The mechanism and products of the reaction of 2-methyl-3-buten-2-ol (MBO232) with Cl atoms in the presence of O2 have been elucidated by performing high-level quantum chemistry calculations. The geometries of the reactants, intermediates, transition states, and products are optimized at the MP2(full)/6-311G(d, p) level, and their single-point energies are refined at the CCSD(T)/6-311 + G(d, p) level. The potential energy surface profiles have been constructed at the CCSD(T)/6-311 + G(d, p)//MP2(full)/6-311G(d, p) + 0.95 × ZPE level of theory, and the possible channels involved in the reaction are also discussed. The calculations indicate that the reaction predominantly proceeds via the addition of Cl atoms to the double bond rather than the direct abstraction of the H atoms in MBO232. The nascent adducts (CH3)2C(OH)CHCH2Cl (IM1) and (CH3)2C(OH)CHClCH2 (IM2) do not undergo subsequent isomerization and dissociation reactions, but rather react with O2. The theoretical results show that the major products are CH2ClCHO and CH3C(O)CH3 for the reaction of MBO232 + Cl in the presence of O2, which is in good agreement with the experimental finding.

The Production and Recovery of C2-C4 Olefins from Syngas.

ERIC Educational Resources Information Center

Murchison, C. B.; And Others

1986-01-01

Discusses reacting coal-derived hydrogen and carbon monoxide (syngas) at relatively high selectivity to ethylene, propylene, and butenes over novel catalysts. In addition, data are given which illustrate a unique ethylene removal step which is compatible with operating the olefin synthesis at low conversion. (JN)

Ionization Study of Isomeric Molecules in Strong-field Laser Pulses

DOE PAGES

Zigo, Stefan; Le, Anh-Thu; Timilsina, Pratap; ...

2017-02-10

Through the use of the technique of time-of-flight mass spectroscopy, we obtain strong-field ionization yields for randomly oriented 1,2-dichloroethylene (1,2-DCE) (C 2H 2Cl 2) and 2-butene (C 4H 8). Here, we are interested in studying the effect of conformal structure in strong-field ionization and, in particular, the role of molecular polarity. That is, we can perform strong-field ionization studies in polar vs non-polar molecules that have the same chemical composition. Here, we report our findings through the ionization yields and the ratio (trans/cis) of each stereoisomer pair as a function of intensity.

Additional conformer observed in the microwave spectrum of methyl vinyl ketone

NASA Astrophysics Data System (ADS)

Wilcox, David S.; Shirar, Amanda J.; Williams, Owen L.; Dian, Brian C.

2011-05-01

A chirped-pulse Fourier transform microwave spectrometer was used to record the rotational spectrum of methyl vinyl ketone (MVK, 3-butene-2-one). Two stable conformations were identified: the previously documented antiperiplanar (ap) conformer and synperiplanar (sp), which is reported for the first time in this microwave study. Methyl torsional analysis resulted in V3 barrier heights of 433.8(1) and 376.6(2) cm-1 for ap- and sp-MVK, respectively. Heavy atom isotopic species of both conformers were detected in natural abundance allowing bond lengths and angles of the molecular frames to be calculated through Kraitchman analysis. A comparison with ab initio calculations is included.

Two new coumarins from Micromelum falcatum with cytotoxicity and brine shrimp larvae toxicity.

PubMed

Luo, Xiongming; He, Weihong; Yin, Hao; Li, Qingxin; Liu, Qiao; Huang, Yongzhong; Zhang, Si

2012-06-06

Two new coumarins, 7-methoxy-8-(2-hydroxmethyl-1-O-isovaleryl-4-butenyl)-coumarin (1) and 7-methoxy-8-(1-hydroxy-2-O-β-glucopyranosyl-3-methyl-4-butene-1-yl)coumarin (2), and twelve known coumarins 3-14 were isolated from the stem bark of Micromelum falcatum. The structures of compounds 1-14 were elucidated by extensive spectroscopic data analyses. The toxicity of compounds 1-14 was tested using a brine shrimp assay and in vitro antiproliferative assay against mammary cancer (F10) and lung cancer (HvEvc) cell lines by the MTT method. Some compounds had moderate activities. All compounds were also tested against the microorganisms Bacillus subtilis, Bacillus thuringiensis and Escherichia coli, but no activity was observed.

Quantitation of DNA Adducts Induced by 1,3-Butadiene

NASA Astrophysics Data System (ADS)

Sangaraju, Dewakar; Villalta, Peter W.; Wickramaratne, Susith; Swenberg, James; Tretyakova, Natalia

2014-07-01

Human exposure to 1,3-butadiene (BD) present in automobile exhaust, cigarette smoke, and forest fires is of great concern because of its potent carcinogenicity. The adverse health effects of BD are mediated by its epoxide metabolites such as 3,4-epoxy-1-butene (EB), which covalently modify genomic DNA to form promutagenic nucleobase adducts. Because of their direct role in cancer, BD-DNA adducts can be used as mechanism-based biomarkers of BD exposure. In the present work, a mass spectrometry-based methodology was developed for accurate, sensitive, and precise quantification of EB-induced N-7-(1-hydroxy-3-buten-2-yl) guanine (EB-GII) DNA adducts in vivo. In our approach, EB-GII adducts are selectively released from DNA backbone by neutral thermal hydrolysis, followed by ultrafiltration, offline HPLC purification, and isotope dilution nanoLC/ESI+-HRMS3 analysis on an Orbitrap Velos mass spectrometer. Following method validation, EB-GII lesions were quantified in human fibrosarcoma (HT1080) cells treated with micromolar concentrations of EB and in liver tissues of rats exposed to sub-ppm concentrations of BD (0.5-1.5 ppm). EB-GII concentrations increased linearly from 1.15 ± 0.23 to 10.11 ± 0.45 adducts per 106 nucleotides in HT1080 cells treated with 0.5-10 μM DEB. EB-GII concentrations in DNA of laboratory rats exposed to 0.5, 1.0, and 1.5 ppm BD were 0.17 ± 0.05, 0.33 ± 0.08, and 0.50 ± 0.04 adducts per 106 nucleotides, respectively. We also used the new method to determine the in vivo half-life of EB-GII adducts in rat liver DNA (2.20 ± 0.12 d) and to detect EB-GII in human blood DNA. To our knowledge, this is the first application of nanoLC/ESI+-HRMS3 Orbitrap methodology to quantitative analysis of DNA adducts in vivo.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Disselkamp, Robert S.; Denslow, Kayte M.; Hart, Todd R.

We have studied the effect of cavitating ultrasound on the heterogeneous aqueous hydrogenation of cis-2-buten-1-ol (C4 olefin) and cis-2-penten-1-ol (C5 olefin) on Pd-black to form the trans-olefins (trans-2-buten-1-ol and trans-2-penten-1-ol) and saturated alcohols (1-butanol and 1-pentanol, respectively). Silent (and magnetically stirred) experiments served as control experiments. As described in an earlier publication by our group, we have added an inert dopant, 1-propanol, in the reaction mixture to ensure the rapid onset of cavitation in the ultrasound-assisted reactions that can lead to altered selectivity compared to silent reaction systems [R.S. Disselkamp, Ya-Huei Chin, C.H.F. Peden, J. Catal. 227 (2004) 552]. Themore » motivation for this study is to examine whether cavitating ultrasound can reduce the [trans-olefin/saturated alcohol] molar ratio during the course of the reaction. This could have practical application in that it may offer an alternative processing methodology of synthesizing healthier edible seed oils by reducing trans-fat content.We have observed that cavitating ultrasound results in a [(trans-olefin/saturated alcohol)ultrasound/(trans-olefin/saturated alcohol)silent] ratio quantity less than 0.5 at the reaction mid-point for both the C4 and C5 olefin systems. This indicates that ultrasound reduces trans-olefin production compared to the silent control experiment. Furthermore, there is an added 30% reduction for the C5 versus C4 olefin compounds again at reaction mid-point. We attribute differences in the ratio quantity as a moment of inertia effect. In principle, the C4 versus C5 olefins has a {approx}52% increase in moment of inertia about C2 C3 double bond slowing isomerization. Since seed oils are C18 multiple cis-olefins and have a moment of inertia even greater than our C5 olefin here, our study suggests that even a greater reduction in trans-olefin content may occur for partial hydrogenation of C18 seed oils.« less

Molecular Structure and Reactivity in the Pyrolysis of Aldehydes

NASA Astrophysics Data System (ADS)

Sias, Eric; Cole, Sarah; Sowards, John; Warner, Brian; Wright, Emily; McCunn, Laura R.

2016-06-01

The effect of alkyl chain structure on pyrolysis mechanisms has been investigated in a series of aldehydes. Isovaleraldehyde, CH_3CH(CH_3)CH_2CHO, and pivaldehyde, (CH_3)_3CCHO, were subject to thermal decomposition in a resistively heated SiC tubular reactor at 800-1200 °C. Matrix-isolation FTIR spectroscopy was used to identify pyrolysis products. Carbon monoxide and isobutene were major products from each of the aldehydes, which is consistent with what is known from previous studies of unbranched alkyl-chain aldehydes. Other products observed include vinyl alcohol, propene, acetylene, and ethylene, revealing complexities to be considered in the pyrolysis of large, branched-chain aldehydes.

ESTIMATES OF REGIONAL NATURAL VOLATILE ORGANIC COMPOUND FLUXES FROM ENCLOSURE AND AMBIENT MEASUREMENTS

EPA Science Inventory

The paper discusses results of an investigation at two forested sites in the Southeastern United States. A variety of VOC compounds including methanol, 2-methyl-3-buten-2-ol, 6-methyl-5-hepten-
2-one, isoprene, and 15 monoterpenes were emitted from vegetation at these sites. D...

77 FR 3750 - Notice of Intent To Grant a Partially Exclusive License; Cobalt Technologies, Inc.

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-25

... described in the following: patent application 61/562231: Water and Contaminants Removal From Butanol...-Butene, filed on July 29, 2009.// patent application 12/769757: Turbine and Diesel Fuels and Methods of... Oligomerization of Olefin Feedstocks for the Production of Turbine and Diesel Fuels, filed on April 27, 2011...

Mechanism of Surface Alkylation of a Gold Aerogel with Tetra-n-butylstannane-d36: Identification of Byproducts.

PubMed

Benkovičová, Monika; Wen, Dan; Plutnar, Jan; Čížková, Martina; Eychmüller, Alexander; Michl, Josef

2017-05-18

The formation of self-assembled monolayers on surfaces is often likely to be accompanied by the formation of byproducts, whose identification holds clues to the reaction mechanism but is difficult due to the minute amounts produced. We now report a successful identification of self-assembly byproducts using gold aerogel with a large specific surface area, a procedure likely to be applicable generally. Like a thin gold layer on a flat substrate, the aerogel surface is alkylated with n-butyl-d 9 groups upon treatment with a solution of tetra-n-butylstannane-d 36 under ambient conditions. The reaction byproducts accumulate in the mother liquor in amounts sufficient for GC-MS analysis. In chloroform solvent, they are butene-d 8 , butane-d 10 , octane-d 18 , and tributylchlorostannane-d 27 . In hexane, they are the same except that tributylchlorostannane-d 27 is replaced with hexabutyldistannane-d 54 . The results are compatible with an initial homolytic dissociation of a C-Sn bond on the gold surface, followed by known radical processes.

Secondary Organic Aerosol Formation from 2-Methyl-3-Buten-2-ol Photooxidation: Evidence of Acid-Catalyzed Reactive Uptake of Epoxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Haofei; Zhang, Zhenfa; Cui, Tianqu

2014-04-08

Secondary organic aerosol (SOA) formation from 2-methyl-3-buten-2-ol (MBO) photooxidation has recently been observed in both field and laboratory studies. Similar to isoprene, MBO-derived SOA increases with elevated aerosol acidity in the absence of nitric oxide; therefore, an epoxide intermediate, (3,3-dimethyloxiran-2-yl)methanol (MBO epoxide) was synthesized and tentatively proposed here to explain this enhancement. In the present study, the potential of the synthetic MBO epoxide to form SOA via reactive uptake was systematically examined. SOA was observed only in the presence of acidic aerosols. Major SOA constituents, 2,3-dihydroxyisopentanol (DHIP) and MBO-derived organosulfate isomers, were chemically characterized in both laboratory-generated SOA and inmore » ambient fine aerosols collected from the BEACHON-RoMBAS field campaign during summer 2011, where MBO emissions are substantial. Our results support epoxides as potential products of MBO photooxidation leading to formation of atmospheric SOA and suggest that reactive uptake of epoxides may generally explain acid enhancement of SOA observed from other biogenic hydrocarbons.« less

Measurement of the ( p, , T) Properties for Pure Hydrocarbons at Temperatures up to 600 K and Pressures up to 200 MPa

NASA Astrophysics Data System (ADS)

Ito, T.; Nagata, Y.; Miyamoto, H.

2014-10-01

The data available for the thermodynamic properties of propane, -butane, and isobutane at temperatures above 440 K are outdated and show significant discrepancies with each other. The ambiguity associated with these data could be limiting to the development of any understanding related to the effects of mixing of these substances with other materials such as , ammonia, and non-flammable or lower-flammable HFC refrigerants. In this study, the ( p, , T) properties of propane, -butane, and isobutane were measured at temperatures ranging from (360 to 600) K and pressures ranging from (50 to 200) MPa. Precise measurements were carried out using a metal-bellows variable volumometer with a thermostatted air bath. The expanded uncertainties in the temperature, pressure, and density measurements were estimated to be 5 mK, 0.02 MPa, and 0.88 kg m ( K, MPa), 0.76 kg ( K, MPa), 0.76 kg ( K, MPa), and 2.94 kg ( K, MPa), respectively. The data obtained throughout this study were systematically compared with the calculated values derived from the available equations of state. These models agree well with the measured data at higher temperatures up to 600 K, demonstrating their suitability for an effective and precise examination of the mixing effects of potential alternative mixtures.

Pathway and Surface Mechanism Studies of 1,3-butadiene Selective Oxidation Over Vanadium-Molybdenum-Oxygen Catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schroeder, William David

2001-01-01

The partial oxidation of 1,3-butadiene has been investigated over VMoO catalysts synthesized by sol-gel techniques. Surface areas were 9-14 m 2/g, and compositions were within the solid solution regime, i.e. below 15.0 mol % MoO 3/(MoO 3 + V 2O 5). Laser Raman Spectroscopy and XRD data indicated that solid solutions were formed, and pre- and post-reaction XPS data indicated that catalyst surfaces contained some V +4 and were further reduced in 1,3-butadiene oxidation. A reaction pathway for 1,3-butadiene partial oxidation to maleic anhydride was shown to involve intermediates such as 3,4-epoxy-1-butene, crotonaldehyde, furan, and 2-butene-1,4-dial. The addition of watermore » to the reaction stream substantially increased catalyst activity and improved selectivity to crotonaldehyde and furan at specific reaction temperatures. At higher water addition concentrations, furan selectivity increased from 12% to over 25%. The catalytic effects of water addition were related to competitive adsorption with various V 2O 5-based surface sites, including the vanadyl V=O, corner sharing V-O-V and edge sharing V-O oxygen. Higher levels of water addition were proposed to impose acidic character by dissociative adsorption. In addition, a novel combinatorial synthesis technique for VMoO was used to investigate the phase transitions of V 2O 5, solid solutions of Mo in V 2O 5, V 9Mo 6O 40, and other reduced VMoO compounds, characterized by laser Raman spectroscopy. The natural composition gradient imposed by the sputter deposition apparatus was used to create VMoO arrays containing 225 samples ranging from 7.0-42 mol% MoO 3/(V 2O 5 + MoO 3), determined by EDS analysis.« less

Antiproliferative constituents in plants 14. Coumarins and acridone alkaloids from Boenninghausenia japonica NAKAI.

PubMed

Chaya, Norihito; Terauchi, Kazuko; Yamagata, Yuriko; Kinjo, Junei; Okabe, Hikaru

2004-08-01

The MeOH extracts of the ground part and the root of Boenninghausenia japonica NAKAI showed inhibitory activity against tumor cell growth. Fractionation of the extracts has resulted in isolation of 1,3-dihydroxy-4-(2'-hydroxy-3'-hydroxymethyl-3',4'-epoxy-butyl)-N-methylacridone, 1,3-dihydroxy-4-[(Z)-3'-hydroxy-3'-methyl-buten-1'-yl]-N-methylacridone, 3-(1',1'-dimethylallyl)-7-hydroxy-8-methoxy-2H-1-benzopyran-2-one, casegravol, cis-casegravol, and edgeworin in addition to 9 compounds reported from B. japonica and B. albiflora. The isolates from this plant and some related compounds were tested for antiproliferative activity against human gastric adenocarcinoma (MK-1), human uterus carcinoma (HeLa), and murine melanoma (B16F10) cells.

Organosulfates as tracers for secondary organic aerosol (SOA) formation from 2-methyl-3-buten-2-ol (MBO) in the atmosphere.

PubMed

Zhang, Haofei; Worton, David R; Lewandowski, Michael; Ortega, John; Rubitschun, Caitlin L; Park, Jeong-Hoo; Kristensen, Kasper; Campuzano-Jost, Pedro; Day, Douglas A; Jimenez, Jose L; Jaoui, Mohammed; Offenberg, John H; Kleindienst, Tadeusz E; Gilman, Jessica; Kuster, William C; de Gouw, Joost; Park, Changhyoun; Schade, Gunnar W; Frossard, Amanda A; Russell, Lynn; Kaser, Lisa; Jud, Werner; Hansel, Armin; Cappellin, Luca; Karl, Thomas; Glasius, Marianne; Guenther, Alex; Goldstein, Allen H; Seinfeld, John H; Gold, Avram; Kamens, Richard M; Surratt, Jason D

2012-09-04

2-Methyl-3-buten-2-ol (MBO) is an important biogenic volatile organic compound (BVOC) emitted by pine trees and a potential precursor of atmospheric secondary organic aerosol (SOA) in forested regions. In the present study, hydroxyl radical (OH)-initiated oxidation of MBO was examined in smog chambers under varied initial nitric oxide (NO) and aerosol acidity levels. Results indicate measurable SOA from MBO under low-NO conditions. Moreover, increasing aerosol acidity was found to enhance MBO SOA. Chemical characterization of laboratory-generated MBO SOA reveals that an organosulfate species (C(5)H(12)O(6)S, MW 200) formed and was substantially enhanced with elevated aerosol acidity. Ambient fine aerosol (PM(2.5)) samples collected from the BEARPEX campaign during 2007 and 2009, as well as from the BEACHON-RoMBAS campaign during 2011, were also analyzed. The MBO-derived organosulfate characterized from laboratory-generated aerosol was observed in PM(2.5) collected from these campaigns, demonstrating that it is a molecular tracer for MBO-initiated SOA in the atmosphere. Furthermore, mass concentrations of the MBO-derived organosulfate are well correlated with MBO mixing ratio, temperature, and acidity in the field campaigns. Importantly, this compound accounted for an average of 0.25% and as high as 1% of the total organic aerosol mass during BEARPEX 2009. An epoxide intermediate generated under low-NO conditions is tentatively proposed to produce MBO SOA.

The Microwave Spectrum of Methyl Vinyl Ketone Revisited

NASA Astrophysics Data System (ADS)

Wilcox, David S.; Shirar, Amanda J.; Williams, Owen L.; Dian, Brian C.

2011-06-01

A chirped-pulse Fourier transform microwave spectrometer was used to record the rotational spectrum of methyl vinyl ketone (MVK, 3-butene-2-one) from 6 to 18.9 GHz. Two stable conformations were identified: the previously documented antiperiplanar (ap) conformer and synperiplanar (sp), which is reported for the first time in this microwave study. Methyl torsional analysis with XIAM resulted in V3 barrier heights of 433.8(1) and 376.6(2) Cm-1 for ap- and sp-MVK, respectively. Heavy atom isotopic species were detected in natural abundance allowing bond lengths and angles of the molecular frames to be calculated through Kraitchman analysis. A comparison with ab initio calculations is included.

Solvation and Acid Strength Effects on Catalysis by Faujasite Zeolites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gounder, Rajamani P.; Jones, Andrew J.; Carr, Robert T.

2012-02-01

Kinetic, spectroscopic, and chemical titration data indicate that differences in monomolecular isobutane cracking and dehydrogenation and methanol dehydration turnover rates (per H+) among FAU zeolites treated thermally with steam (H-USY) and then chemically with ammonium hexafluorosilicate (CDHUSY) predominantly reflect differences in the size and solvating properties of their supercage voids rather than differences in acid strength. The number of protons on a given sample was measured consistently by titrations with Na+, with CH3 groups via reactions of dimethyl ether, and with 2,6-di-tert-butylpyridine during methanol dehydration catalysis; these titration values were also supported by commensurate changes in acidic OH infrared bandmore » areas upon exposure to titrant molecules. The number of protons, taken as the average of the three titration methods, was significantly smaller than the number of framework Al atoms (Alf) obtained from X-ray diffraction and 27Al magic angle spinning nuclear magnetic resonance spectroscopy on H-USY (0.35 H+/Alf) and CD-HUSY (0.69 H+/Alf). These data demonstrate that the ubiquitous use of Alf sites as structural proxies for active H+ sites in zeolites can be imprecise, apparently because distorted Al structures that are not associated with acidic protons are sometimes detected as Alf sites. Monomolecular isobutane cracking and dehydrogenation rate constants, normalized non-rigorously by the number of Alf species, decreased with increasing Na+ content on both H-USY and CD-HUSY samples and became undetectable at sub-stoichiometric exchange levels (0.32 and 0.72 Na+/Alf ratios, respectively), an unexpected finding attributed incorrectly in previous studies to the presence of minority ‘‘super-acidic’’ sites. These rate constants, when normalized rigorously by the number of residual H+ sites were independent of Na+ content on both H-USY and CD-HUSY samples, reflecting the stoichiometric replacement of protons that are uniform in reactivity by Na+ cations. Monomolecular isobutane cracking and dehydrogenation rate constants (per H+; 763 K), however, were higher on H-USY than CD-HUSY (by a factor of 1.4). Equilibrium constants for the formation of protonated methanol dimers via adsorption of gaseous methanol onto adsorbed methanol monomers, determined from kinetic studies of methanol dehydration to dimethyl ether (433 K), were also higher on H-USY than CD-HUSY (by a factor of 2.1). These larger constants predominantly reflect stronger dispersive interactions in H-USY, consistent with its smaller supercage voids that result from the occlusion of void space by extraframework Al (Alex) residues. These findings appear to clarify enduring controversies about the mechanistic interpretation of the effects of Na+ and Alex species on the catalytic reactivity of FAU zeolites. They also illustrate the need to normalize rates by the number of active sites instead of more convenient but less accurate structural proxies for such sites.« less

Three-Dimensional Conformation of Folded Polymers in Single Crystals

NASA Astrophysics Data System (ADS)

Hong, You-lee; Yuan, Shichen; Li, Zhen; Ke, Yutian; Nozaki, Koji; Miyoshi, Toshikazu

2015-10-01

The chain-folding mechanism and structure of semicrystalline polymers have long been controversial. Solid-state NMR was applied to determine the chain trajectory of 13C CH3 -labeled isotactic poly(1-butene) (i PB 1 ) in form III chiral single crystals blended with nonlabeled i PB 1 crystallized in dilute solutions under low supercooling. An advanced 13C - 13C double-quantum NMR technique probing the spatial proximity pattern of labeled 13C nuclei revealed that the chains adopt a three-dimensional (3D) conformation in single crystals. The determined results indicate a two-step crystallization process of (i) cluster formation via self-folding in the precrystallization stage and (ii) deposition of the nanoclusters as a building block at the growth front in single crystals.

Substantially isotactic, linear, alternating copolymers of carbon monoxide and an olefin

DOEpatents

Sen, Ayusman; Jiang, Zhaozhong

1996-01-01

The compound, [Pd(Me-DUPHOS)(MeCN).sub.2 ](BF.sub.4).sub.2, [Me-DUPHOS: 1,2-bis(2,5-dimethylphospholano)benzene] is an effective catalyst for the highly enantioselective, alternating copolymerization of olefins, such as aliphatic .alpha.-olefins, with carbon monoxide to form optically active, isotactic polymers which can serve as excellent starting materials for the synthesis of other classes of chiral polymers. For example, the complete reduction of a propylene-carbon monoxide copolymer resulted in the formation of a novel, optically active poly(1,4-alcohol). Also, the previously described catalyst is a catalyst for the novel alternating isomerization cooligomerization of 2-butene with carbon monoxide to form optically active, isotactic poly(1,5-ketone)

Substantially isotactic, linear, alternating copolymers of carbon monoxide and an olefin

DOEpatents

Sen, A.; Jiang, Z.

1996-05-28

The compound, [Pd(Me-DUPHOS)(MeCN){sub 2}](BF{sub 4}){sub 2}, [Me-DUPHOS: 1,2-bis(2,5-dimethylphospholano)benzene] is an effective catalyst for the highly enantioselective, alternating copolymerization of olefins, such as aliphatic {alpha}-olefins, with carbon monoxide to form optically active, isotactic polymers which can serve as excellent starting materials for the synthesis of other classes of chiral polymers. For example, the complete reduction of a propylene-carbon monoxide copolymer resulted in the formation of a novel, optically active poly(1,4-alcohol). Also, the previously described catalyst is a catalyst for the novel alternating isomerization cooligomerization of 2-butene with carbon monoxide to form optically active, isotactic poly(1,5-ketone).

Influence of Water on the H2SO4 Yield from the Ozonolysis of 2,3-dimethyl-butene (TME) in Presence of SO2

NASA Astrophysics Data System (ADS)

Véronique, D.; Kukui, A.; Chen, H.; Mellouki, A.

2016-12-01

The influence of the water vapor content on the yield of H2SO4 from the ozonolysis of 2,3-dimethyl-butene (TME) in presence of SO2 was studied using laminar flow reactor coupled with Chemical Ionisation Mass Spectrometer (CIMS) for the H2SO4 monitoring within the range of H2O from 10 ppmv to 3×104 ppmv at different concentrations of TME, O3, SO2. The observed dependences of the H2SO4 yield on H2O concentration can be interpreted by assuming two different paths of the H2SO4 formation: 1) via the formation of SO3 in the reaction of Stabilized Criegee Intermediate (SCI) with SO2 (2a) followed by the reaction of SO3 with H2O (3) and 2) via the formation of stabilized secondary ozonide (SOZ) (2b) producing H2SO4 in the reaction with H2O (4a) in competition with the SOZ decomposition to other products (5): O3+TME => (CH3)2COO (1) (CH3)2COO + SO2 => SO3 (2a) => SOZ (2b) SO3 + H2O => H2SO4 (3) SOZ + H2O => H2SO4 (or SO3) (4a) SOZ + M => products (5) The yield of the SCI, SOZ and the rates of the SCI and SOZ decomposition relative to their reactions with SO2 and H2O, respectively, were estimated from the dependencies of the H2SO4 yield on the concentrations of the reactants.

Demonstration of isoleucine 199 as a structural determinant for the selective inhibition of human monoamine oxidase B by specific reversible inhibitors.

PubMed

Hubálek, Frantisek; Binda, Claudia; Khalil, Ashraf; Li, Min; Mattevi, Andrea; Castagnoli, Neal; Edmondson, Dale E

2005-04-22

Several reversible inhibitors selective for human monoamine oxidase B (MAO B) that do not inhibit MAO A have been described in the literature. The following compounds: 8-(3-chlorostyryl)caffeine, 1,4-diphenyl-2-butene, and trans,trans-farnesol are shown to inhibit competitively human, horse, rat, and mouse MAO B with K(i) values in the low micromolar range but are without effect on either bovine or sheep MAO B or human MAO A. In contrast, the reversible competitive inhibitor isatin binds to all known MAO B and MAO A with similar affinities. Sequence alignments and the crystal structures of human MAO B in complex with 1,4-diphenyl-2-butene or with trans,trans-farnesol provide molecular insights into these specificities. These inhibitors span the substrate and entrance cavities with the side chain of Ile-199 rotated out of its normal conformation suggesting that Ile-199 is gating the substrate cavity. Ile-199 is conserved in all known MAO B sequences except bovine MAO B, which has Phe in this position (the sequence of sheep MAO B is unknown). Phe is conserved in the analogous position in MAO A sequences. The human MAO B I199F mutant protein of MAO B binds to isatin (K(i) = 3 microM) but not to the three inhibitors listed above. The crystal structure of this mutant demonstrates that the side chain of Phe-199 interferes with the binding of those compounds. This suggests that the Ile-199 "gate" is a determinant for the specificity of these MAO B inhibitors and provides a molecular basis for the development of MAO B-specific reversible inhibitors without interference with MAO A function in neurotransmitter metabolism.

Structure-property evolution during polymer crystallization

NASA Astrophysics Data System (ADS)

Arora, Deepak

The main theme of this research is to understand the structure-property evolution during crystallization of a semicrystalline thermoplastic polymer. A combination of techniques including rheology, small angle light scattering, differential scanning calorimetry and optical microscopy are applied to follow the mechanical and optical properties along with crystallinity and the morphology. Isothermal crystallization experiments on isotactic poly-1-butene at early stages of spherulite growth provide quantitative information about nucleation density, volume fraction of spherulites and their crystallinity, and the mechanism of connecting into a sample spanning structure. Optical microscopy near the fluid-to-solid transition suggests that the transition, as determined by time-resolved mechanical spectroscopy, is not caused by packing/jamming of spherulites but by the formation of a percolating network structure. The effect of strain, Weissenberg number (We ) and specific mechanical work (w) on rate of crystallization (nucleation followed by growth) and on growth of anisotropy was studied for shear-induced crystallization of isotactic poly-1-butene. The samples were sheared for a finite strain at the beginning of the experiment and then crystallized without further flow (Janeschitz-Kriegl protocol). Strain requirements to attain steady state/leveling off of the rate of crystallization were found to be much larger than the strain needed to achieve steady state of flow. The large strain and We>1 criteria were also observed for morphological transition from spherulitic growth to oriented growth. An apparatus for small angle light scattering (SALS) and light transmission measurements under shear was built and tested at the University of Massachusetts Amherst. As a new development, the polarization direction can be rotated by a liquid crystal polarization rotator (LCPR) with a short response time of 20 ms. The experiments were controlled and analyzed with a LabVIEW(TM) based code (LabVIEW(TM) 7.1) in real time. The SALS apparatus was custom built for ExxonMobil Research in Clinton NJ.

RUTHENIUM-CATALYZED TANDEM OLEFIN MIGRATION-ALDOL AND MANNICH-TYPE REACTIONS IN IONIC LIQUID.

EPA Science Inventory

In the presence of a catalytic amount of RuCl2(PPh3)3, a cross-coupling of 3-buten-2-ol with aldehydes and imines was developed via a tandem olefin migration--aldol--Mannich reaction in bmim[PF6]. With In(OAc)3 as a co-catalyst, a-vinylbenzyl alcohol and aldehydes underwent sim...

More environment-friendly and safer working gas mixtures for Bakelite RPCs operated in streamer mode

NASA Astrophysics Data System (ADS)

Zhang, Qingmin; Lv, Zhipeng; Lv, Jinge; Zhang, Jiawen; Xu, Jilei; Ning, Zhe

2017-08-01

This paper presents experimental results of RPCs performances with different working gas mixtures. Owing to Freon's high global warming potential, its threat to RPCs aging and its large consumption in large particle physics experiments, studies to minimize the concentration of HFC-134A, and even its complete replacement, have been undertaken. In addition, the reduction of iso-butane is also a favorable strategy, due to the flammability level of the gas mixture. Freon-less working gas mixture of Ar/HFC-134A/i-C4H10/CO2=20/0/8/72 was chosen with plateau efficiency of 86.3% and noise rate of 0.61 Hz/cm2. For working gas with lower ratio of Freon, Ar/HFC-134A/i-C4H10/CO2=20/20/8/52 was suggested with plateau efficiency of 91.0% and noise rate of 0.19 Hz/cm2, in which Freon was decreased by 22% compared to the BESIII RPC gas mixture. Furthermore, iso-butane was decreased to 6% with RPC's efficiency of 90% and noise rate of 0.20 Hz/cm2 achieved. Finally, the explanation of RPC's different performances at various working gas mixtures has been validated by the investigation of secondary streamers. This study will be helpful for RPC's application in future large particle physics experiments, in which RPCs can run in streamer mode.

Effect of modification methods on the surface properties and n-butane isomerization performance of La/Ni-promoted SO42-/ZrO2-Al2O3

NASA Astrophysics Data System (ADS)

Wang, Pengzhao; Zhang, Jiaoyu; Han, Chaoyi; Yang, Chaohe; Li, Chunyi

2016-08-01

The La and/or Ni was introduced into alumina-promoted sulfated zirconia by impregnation and co-precipitation to improve the catalytic property of n-butane isomerization. Catalysts characterization shows that the addition of La/Ni has a remarkable influence on the surface and textual properties depending on the modification method. The impregnation of La/Ni facilitates the transformation of a small amount of tetragonal zirconia into monoclinic phase, while the co-precipitation improves the stability of tetragonal ZrO2. H2-TPR indicates that the addition of La/Ni changes the interaction between SO42- and supports, which affects the acidity on the surface. Specifically, the Lewis acidity is significantly enhanced by either modification method. The co-precipitation reserves almost all of the Brønsted acid sites, while the impregnation causes a remarkable decrease of Brønsted acid sites. Reaction results demonstrate that the co-precipitation exhibits a significant advantage over impregnation that the higher conversion of n-butane and selectivity to isobutane are obtained on the catalyst prepared by co-precipitation. The increase of catalytic activity is ascribed to the accelerated activation rate of n-butane molecules by hydride subtraction on the Lewis acid sites at higher reaction temperature. Furthermore, the addition of La/Ni improves the selectivity to isobutane by inhibiting the bimolecular reaction.

A sputtering derived atomic oxygen source for studying fast atom reactions

NASA Technical Reports Server (NTRS)

Ferrieri, Richard A.; Yung, Y. Chu; Wolf, Alfred P.

1987-01-01

A technique for the generation of fast atomic oxygen was developed. These atoms are created by ion beam sputtering from metal oxide surfaces. Mass resolved ion beams at energies up to 60 KeV are produced for this purpose using a 150 cm isotope separator. Studies have shown that particles sputtered with 40 KeV Ar(+) on Ta2O5 were dominantly neutral and exclusively atomic. The atomic oxygen also resided exclusively in its 3P ground state. The translational energy distribution for these atoms peaked at ca 7 eV (the metal-oxygen bond energy). Additional measurements on V2O5 yielded a bimodal distribution with the lower energy peak at ca 5 eV coinciding reasonably well with the metal-oxygen bond energy. The 7 eV source was used to investigate fast oxygen atom reactions with the 2-butene stereoisomers. Relative excitation functions for H-abstraction and pi-bond reaction were measured with trans-2-butene. The abstraction channel, although of minor relative importance at thermal energy, becomes comparable to the addition channel at 0.9 eV and dominates the high-energy regime. Structural effects on the specific channels were also found to be important at high energy.

Environmentally friendly paint and varnish additives based on isobutyrate aldehyde condensation products

NASA Astrophysics Data System (ADS)

Guziałowska-Tic, Joanna; Jan Tic, Wilhelm

2017-10-01

The demand for exploitation of new plasticizers and coalescents to be used for production of water dispersion adhesives based on poli(vinyl acetate), turned to be recently of particular significance because the use of all kind of toxic phthalates was banned and certain restrictions were made to use glycol derivatives classified as volatile organic compounds. An alternative for toxic plasticizers used for production of adhesives is hydroxyester (HE-1) obtained from isobutanal during the process of aldol condensation under subsequent Cannizaro and Tischenko reactions. The paper presents selected results of ecotoxicological tests on the environmental impact of hydroxyester HE-1. It was found that the substance is biodegradable and has no negative impact on algae growth rate, however it may inhibit algae biomass growth. The results of Daphnia immobilization test shows that the substance is safe for the aquatic environment. Whereas, at higher concentrations, hydroxyester HE-1 may exhibit acute toxicity to rainbow trout.

Process for producing high purity isoolefins and dimers thereof by dissociation of ethers

DOEpatents

Smith, L.A. Jr.; Jones, E.M. Jr.; Hearn, D.

1984-05-08

Alkyl tertiary butyl ether or alkyl tertiary amyl ether is dissociated by vapor phase contact with a cation acidic exchange resin at temperatures in the range of 150 to 250 F at LHSV of 0.1 to 20 to produce a stream consisting of unreacted ether, isobutene or isoamylene and an alcohol corresponding to the alkyl radical. After the alcohol is removed, the ether/isoolefin stream may be fractionated to obtain a high purity isoolefin (99+%) or the ether/isoolefin stream can be contacted in liquid phase with a cation acidic exchange resin to selectively dimerize the isoolefin in a highly exothermic reaction, followed by fractionation of the dimerization product to produce high purity diisoolefin (97+%). In the case where the alkyl is C[sub 3] to C[sub 6] and the corresponding alcohol is produced on dissociation of the ether, combined dissociation-distillation may be carried out such that isoolefin is the overhead product and alcohol the bottom. 2 figs.

Process for producing high purity isoolefins and dimers thereof by dissociation of ethers

DOEpatents

Smith, Jr., Lawrence A.; Jones, Jr., Edward M.; Hearn, Dennis

1984-01-01

Alkyl tertiary butyl ether or alkyl tertiary amyl ether is dissociated by vapor phase contact with a cation acidic exchange resin at temperatures in the range of 150.degree. to 250.degree. F. at LHSV of 0.1 to 20 to produce a stream consisting of unreacted ether, isobutene or isoamylene and an alcohol corresponding to the alkyl radical. After the alcohol is removed, the ether/isoolefin stream may be fractionated to obtain a high purity isoolefin (99+%) or the ether/isoolefin stream can be contacted in liquid phase with a cation acidic exchange resin to selectively dimerize the isoolefin in a highly exothermic reaction, followed by fractionation of the dimerization product to produce high purity diisoolefin (97+%). In the case where the alkyl is C.sub.3 to C.sub.6 and the corresponding alcohol is produced on dissociation of the ether, combined dissociation-distillation may be carried out such that isoolefin is the overhead product and alcohol the bottom.

Nontoxic, Hydrophilic Cationic Polymers-Identified as Class of Antimicrobial Polymers.

PubMed

Strassburg, Arne; Kracke, Frauke; Wenners, Julia; Jemeljanova, Anna; Kuepper, Jannis; Petersen, Hanne; Tiller, Joerg C

2015-12-01

Amphiphilic polycations are an alternative to biocides but also toxic to mammalian cells. Antimicrobially active hydrophilic polycations based on 1,4-dibromo-2-butene and tetramethyl-1,3-propanediamine named PBI are not hemotoxic for porcine red blood cells with a hemocytotoxicity (HC50) of more than 40,000 μg · mL(-1). They are quickly killing bacterial cells at their MIC (minimal inhibitory concentration). The highest found selectivity HC50 /MIC is more than 20,000 for S. epidermidis. Investigations on sequentially prepared PBIs with defined molecular weight Mn and tailored end groups revealed that there is a dependence of antimicrobial activity and selectivity on Mn and nature of the end groups. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Grignard-like Organic Reaction in Water

NASA Astrophysics Data System (ADS)

Breton, Gary W.; Hughey, Christine A.

1998-01-01

The addition of a Grignard reagent to a carbonyl-containing compound to form an alcohol is an important reaction to demonstrate in organic chemistry laboratory courses. However, the reaction presents several practical problems for the lab instructor including the need for anhydrous solvents (e.g., ether), dry glassware, and the occasional problem of slow reaction initiation. We have scaled, and tested, a known Grignard-like reaction between allyl bromide and benzaldehyde mediated by zinc metal in aqueous media. The procedure retains the desirable features of the traditional Grignard reaction, while eliminating some of the commonly encountered difficulties. Thus, addition of allyl bromide (1.2 eq) to benzaldehyde and zinc in a two-phase mixture of THF and saturated aqueous NH4Cl afforded addition product 1-phenyl-3-buten-1-ol in 70-85% yields.

Mammalian pheromones VIII Chemical characterization of preorbital gland secretion of grey duiker,Sylvicapra grimmia (Artiodactyla: Bovidae).

PubMed

Burger, B V; Pretorius, P J; Spies, H S; Bigalke, R C; Grierson, G R

1990-02-01

Using gas chromatography-mass spectrometry 33 constituents of the preorbital gland of the grey duiker,Sylvicapra grimmia, were identified as unbranched alkanes, 2-alkanones, alkanals, alkanoic acids, alkan-4-olides, as well as 3-methyl-3-buten-1-ol, (Z)-9-octadecenoic acid, benzyl cyanide, diethyl sulfoxide, 2-isobutyl-1,3-thiazole, 2-isobutyl-4,5-dihydro-1,3-thiazole, and 3,4-epoxy-2-dodecanone. Determination of the relative concentrations of these components in a limited number of secretion samples taken from males and females revealed that in these samples the two thiazole derivatives and the epoxy ketone were present in consistently and significantly higher concentrations in male than in female secretions. This suggests that they could act as sex recognition cues.

Characterization of the Major Purine and Pyrimidine Adducts Formed after Incubations of 1-Chloro-3-buten-2-one with Single-/Double-Stranded DNA and Human Cells.

PubMed

Liu, Ling-Yan; Zheng, Jin; Kong, Cong; An, Jing; Yu, Ying-Xin; Zhang, Xin-Yu; Elfarra, Adnan A

2017-02-20

We have previously shown that 1-chloro-3-buten-2-one (CBO), a potential reactive metabolite of 1,3-butadiene (BD), exhibits potent cytotoxicity and genotoxicity that have been attributed in part to its reactivity toward DNA. In an effort to identify the DNA adducts of CBO, we characterized the CBO reactions with 2'-deoxyguanosine (dG), 2'-deoxycytidine (dC), and 2'-deoxyadenosine (dA) under in vitro physiological conditions (pH 7.4, 37 °C). In the present study, we investigated the CBO reaction with 2'-deoxythymidine (dT) and compared the rate constants of the reactions of CBO with dA, dC, dG, and dT at both individual- and mixed-nucleosides levels. We also investigated the reactions of CBO with single- and double-stranded DNA using HPLC with UV detection after adducts were released by either acid or enzymatic hydrolysis of DNA. Consistent with the results from the nucleoside reactions and the rate constant experiments, 1,N 6 -(1-hydroxy-1-chloromethylpropan-1,3-diyl)adenine (A-2D) was identified as the major DNA adduct detected after acid hydrolysis, followed by N7-(4-chloro-3-oxobutyl)guanine (CG-2H) and a small amount of 1,N 6 -(1-hydroxy-1-hydroxymethylpropan-1,3-diyl)adenine (A-1D). After enzymatic hydrolysis, 1,N 6 -(1-hydroxy-1-hydroxymethylpropan-1,3-diyl)-2'-dexoyadenosine (dA-1), 3,N 4 -(1-hydroxy-1-hydroxymethylpropan-1,3-diyl)-2'-deoxycytidine (dC-1/2), and 1,N 2 -(3-hydroxy-3-hydroxymethylpropan-1,3-diyl)-2'-dexoyguanosine (CG-1) were detected, with dA-1 being the major product, followed by dC-1/2. When a nontoxic concentration of CBO (1 μM) was incubated with HepG2 cells, no adducts could be detected by LC-MS. However, pretreatment of cells with l-buthionine sulfoximine to deplete GSH levels allowed A-2D to be consistently detected in cellular DNA. These results may contribute to a better understanding of the role of the DNA adducts in CBO genotoxicity and mutagenicity. It also suggests that A-2D could be developed as a biomarker of CBO formation after BD exposure in vivo.

Refining of Military Jet Fuels from Shale Oil. Part III. Pilot Plant Sample Preparation.

DTIC Science & Technology

1982-07-01

product gas composition, regen- erator flue gas composition, and carbon contents of the spent and regenerated catalysts were also monitored for...product. Gas samples were collected at eight-hour intervals from the reactor product gas and regenerator flue gas streams and analyzed for material balance...Isobutane C4= Butylene C5 Pentane C5s Pentane and Pentenes I+ C5+, >C5 Compounds Heavier than Pentane in Gas .* Streams C6 Hexane C/H Carbon-to

High-temperature Y267 EPDM elastomer field and laboratory experiences, September 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirasuna, Alan R.; Friese, Gilbert J.; Stephens, Clifford A.

1982-10-08

High performance elastomers were developed for hostile geothermal environments which clearly advance the state-of-the-art. The Y267 EPDM compound is eminently successful and has accumulated broad laboratory and field test experience. Over 15 separate tests are reviewed with about 95% performed independently by other organizations. The tests include a broad spectrum of environments with temperatures in excess of 320 C (608 F), differential pressures up to 138 MPa (20,000 psi) and in fluids including brine, oils, isobutane, and others.

Synthesis of hydrocarbons by CO2 fluid conversion with hydrogen: Experimental modeling at 7.8 GPa and 1350°C

NASA Astrophysics Data System (ADS)

Sokol, A. G.; Tomilenko, A. A.; Bul'bak, T. A.; Sobolev, N. V.

2017-12-01

Synthesis of hydrocarbons by the interaction of a CO2 fluid with hydrogen mantle domains has been simulated in an experiment at 7.8 GPa and 1350°C. The synthesized fluid contains mainly aldehydes; lower amounts of ketones, alcohols, esters, and ethers; as well as noticeable amounts of isobutane and butane, alkenes, arenes, and polycyclic aromatic and heterocyclic hydrocarbons. The fluid is compositionally close to volatiles found in inclusions from mantle olivines and picroilmenites.

Novel adducts from the reaction of 1-chloro-3-buten-2-one with 2'-deoxyguanosine. Structural characterization and potential as tools to investigate 1,3-butadiene carcinogenicity.

PubMed

Zheng, Jin; Li, Yan; Yu, Ying-Xin; An, Jing; Zhang, Xin-Yu; Elfarra, Adnan A

2015-01-25

1-Chloro-3-buten-2-one (CBO) is a potential reactive metabolite of 1,3-butadiene (BD), a carcinogenic air pollutant. To develop tools that may help investigate the role of CBO in BD carcinogenicity and to develop biomarkers that can be used to assess BD exposure, the reaction of CBO with 2'-deoxyguanosine (dG) under in vitro physiological conditions (pH 7.4, 37°C) was investigated and the products (designated as CG-1, CG-2, CG-3, CG-4, CG-5, and CG-6 based on their retention times on HPLC) were characterized by MS and NMR spectroscopy. The structures of CG-1, CG-2, CG-3, and CG-4 were 1,N2-(3-hydroxy-3-hydroxymethylpropan-1,3-diyl)-2'-deoxyguanosine, N7-(4-chloro-3-oxobutyl)-2'-deoxyguanosine, N7,8-(3-hydroxy-3-chloromethylpropan-1,3-diyl)guanine and N2-(4-chloro-3-oxobutyl)-2'-deoxyguanosine, respectively. CG-5 and CG-6, a pair of diastereomers, were characterized as 1,N2-(3-hydroxy-3-chloromethylpropan-1,3-diyl)-2'-deoxyguanosine. CG-1 was stable under in vitro physiological conditions, whereas CG-2, CG-3, CG-4, and CG-5/6 were unstable and exhibited the half-lives at <1.0, 4.8±0.1, 6.7±0.3, and 2.7±0.1 h, respectively. CG-2 decomposed primarily via a retro-Michael reaction to produce dG and CBO, with only a small fraction of CG-2 degrading to CG-3. Decomposition of CG-4 proceeded via a cyclization reaction and/or replacement of the chlorine atom by a hydroxyl group to form 1,N2-(1-hydroxy-1-hydroxymethylpropan-1,3-diyl)-2'-deoxyguanosine (CG-4D1) and N(2)-(4-hydroxy-3-oxobutyl)-2'-deoxyguanosine (CG-4D2), whereas decomposition of CG-5/6 yielded CG-1. Collectively, the newly characterized CBO adducts could be used to investigate the role of CBO in the mechanism of BD carcinogenicity and could also be used to develop biomarkers for BD exposure. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

GOSSIP: A vertex detector combining a thin gas layer as signal generator with a CMOS readout pixel array

NASA Astrophysics Data System (ADS)

Campbell, M.; Heijne, E. H. M.; Llopart, X.; Colas, P.; Giganon, A.; Giomataris, Y.; Chefdeville, M.; Colijn, A. P.; Fornaini, A.; van der Graaf, H.; Kluit, P.; Timmermans, J.; Visschers, J. L.; Schmitz, J.

2006-05-01

A small TPC has been read out by means of a Medipix2 chip as direct anode. A Micromegas foil was placed 50 μm above the chip, and electron multiplication occurred in the gap. With a He/isobutane 80/20 mixture, gas multiplication factors up to tens of thousands were achieved, resulting in an efficiency for detecting single electrons of better than 90%. With this new readout technology for gas-filled detectors we recorded many image frames containing 2D images with tracks from cosmic muons. Along these tracks, electron clusters were observed, as well as δ-rays. With a gas layer thickness of only 1 mm, the device could be applied as vertex detector, outperforming all Si-based detectors.

Short-Term Outlook for Hydrocarbon Gas Liquids

EIA Publications

2016-01-01

U.S. liquid fuels production increased from 7.43 million barrels per day (b/d) in 2008 to 13.75 million b/d in 2015. However, the Short-Term Energy Outlook (STEO) expects liquid fuels production to decline to 12.99 million b/d in 2017, mainly as a result of prolonged low oil prices. The liquid fuels production forecast reflects a 1.24 million b/d decline in crude oil production by 2017 that is partially offset by a 450,000 b/d increase in the production of hydrocarbon gas liquids (HGL)—a group of products including ethane, propane, butane (normal and isobutane), natural gasoline, and refinery olefins. This analysis will discuss the outlook for each of these four HGL streams and related infrastructure projects through 2017.

Identification of Furan Metabolites Derived from Cysteine-cis-2-Butene-1,4-Dial-Lysine Crosslinks

PubMed Central

Lu, Ding; Peterson, Lisa A.

2010-01-01

Furan is a rodent hepatotoxicant and carcinogen. Since this compound is an important industrial intermediate and has been detected in heat-processed foods and smoke, humans are likely exposed to this toxic compound. Characterization of urinary metabolites of furan will lead to the development of biomarkers to assess human health risks associated with furan exposure. Previous studies indicate that furan is oxidized to a reactive α, β-unsaturated dialdehyde, cis-2-butene-1,4-dial (BDA), in a reaction catalyzed by cytochrome P450. Five previously characterized metabolites are derived from the reaction of BDA with cellular nucleophiles such as glutathione and protein. They include the mono-glutathione reaction product, N-[4-carboxy-4-(3-mercapto-1H-pyrrol-1-yl)-1-oxobutyl]-L-cysteinylglycine cyclic sulfide and its downstream metabolite, S-[1-(1,3-dicarboxypropyl)-1H-pyrrol-3-yl]methylthiol as well as R-2-acetylamino-6-(2,5-dihydro-2-oxo-1H-pyrrol-1-yl)-1-hexanoic acid and N-acetyl-S-[1-(5-acetylamino-5-carboxypentyl)-1H-pyrrol-3-yl]-L-cysteine and its sulfoxide. The last two compounds are downstream metabolites of a BDA-derived cysteine-lysine crosslink, S-[1-(5-amino-5-carboxypentyl)-1H-pyrrol-3-yl]-L-cysteine. In this report, we present the characterization of seven additional urinary furan metabolites, all of which are derived from this crosslink. The cysteinyl residue is subject to several biotransformation reactions, including N-acetylation and S-oxidation. Alternatively, it can undergo β-elimination followed by S-methylation to a methylthiol intermediate that is further oxidized to a sulfoxide. The lysine portion of the crosslink is either N-acetylated or undergoes an oxidative transamination reaction to generate an α-ketoacid metabolite that undergoes oxidative decarboxylation. Some of these metabolites are among the most abundant furan metabolites present in urine as judged by LC-MS/MS analysis, indicating that the oxidation of furan to BDA and BDA’s subsequent reaction with cellular cysteine and lysine residues may represent a significant in vivo pathway of furan biotransformation. Since they are derived from cellular BDA reaction products, these metabolites are markers of furan exposure and bioactivation and could be explored as potential biomarkers in human studies. PMID:20043645

Molybdenum chloride catalysts for Z-selective olefin metathesis reactions

NASA Astrophysics Data System (ADS)

Koh, Ming Joo; Nguyen, Thach T.; Lam, Jonathan K.; Torker, Sebastian; Hyvl, Jakub; Schrock, Richard R.; Hoveyda, Amir H.

2017-01-01

The development of catalyst-controlled stereoselective olefin metathesis processes has been a pivotal recent advance in chemistry. The incorporation of appropriate ligands within complexes based on molybdenum, tungsten and ruthenium has led to reactivity and selectivity levels that were previously inaccessible. Here we show that molybdenum monoaryloxide chloride complexes furnish higher-energy (Z) isomers of trifluoromethyl-substituted alkenes through cross-metathesis reactions with the commercially available, inexpensive and typically inert Z-1,1,1,4,4,4-hexafluoro-2-butene. Furthermore, otherwise inefficient and non-stereoselective transformations with Z-1,2-dichloroethene and 1,2-dibromoethene can be effected with substantially improved efficiency and Z selectivity. The use of such molybdenum monoaryloxide chloride complexes enables the synthesis of representative biologically active molecules and trifluoromethyl analogues of medicinally relevant compounds. The origins of the activity and selectivity levels observed, which contradict previously proposed principles, are elucidated with the aid of density functional theory calculations.

Histrionicotoxins: roentgen-ray analysis of the novel allenic and acetylenie spiroalkaloids isolated from a Colombian frog, Dendrobates histrionicus.

PubMed

Daly, J W; Karle, I; Myers, C W; Tokuyama, T; Waters, J A; Witkop, B

1971-08-01

The structures and absolute configuration of two unique alkaloids isolated from the Colombian frog, Dendrobates histrionicus, have been elucidated by Roentgen-ray (x-ray) crystallography. Histrionicotoxin is (2pR, 6S, 7pS, 8aS)-7-(cis-1-buten-3-ynyl)-8-hydroxy-2-(cis-2-penten-4- ynyl)-1-azaspiro[5.5] undecane, while in dihydro-isohistrionicotoxin the acetylenic 2-pentenynyl side chain is replaced by an allenic 2-(3,4 pentadienyl) substituent. Dendrobates histrionicus exhibits remarkable interpopulational variations in amounts and composition of skin toxins, in behavior, and in phenotypic characters, aspects of which are illustrated in a color plate. The histrionico-toxins are the third class of alkaloids isolated from the defensive skin secretions of Neotropical (Dendrobatidae) frogs.

2-Methyl-3-buten-2-ol (MBO) synthase expression in Nostoc punctiforme leads to over production of phytols.

PubMed

Gupta, Dinesh; Ip, Tina; Summers, Michael L; Basu, Chhandak

2015-01-01

Phytol is a diterpene alcohol of medicinal importance and it also has potential to be used as biofuel. We found over production of phytol in Nostoc punctiforme by expressing a 2-Methyl-3-buten-2-ol (MBO) synthase gene. MBO synthase catalyzes the conversion of dimethylallyl pyrophosphate (DMAPP) into MBO, a volatile hemiterpene alcohol, in Pinus sabiniana. The result of enhanced phytol production in N. punctiforme, instead of MBO, could be explained by one of the 2 models: either the presence of a native prenyltransferase enzyme with a broad substrate specificity, or appropriation of a MBO synthase metabolic intermediate by a native geranyl diphosphate (GDP) synthase. In this work, an expression vector with an indigenous petE promoter for gene expression in the cyanobacterium N. punctiforme was constructed and MBO synthase gene expression was successfully shown using reverse transcriptase (RT)-PCR and SDS-PAGE. Gas chromatography--mass spectrophotometry (GC-MS) was performed to confirm phytol production from the transgenic N. punctiforme strains. We conclude that the expression of MBO synthase in N. punctiforme leads to overproduction of an economically important compound, phytol. This study provides insights about metabolic channeling of isoprenoids in cyanobacteria and also illustrates the challenges of bioengineering non-native hosts to produce economically important compounds.

On-fiber furan formation from volatile precursors: a critical example of artefact formation during Solid-Phase Microextraction.

PubMed

Adams, An; Van Lancker, Fien; De Meulenaer, Bruno; Owczarek-Fendor, Agnieszka; De Kimpe, Norbert

2012-05-15

For the analysis of furan, a possible carcinogen formed during thermal treatment of food, Solid-Phase Microextraction (SPME) is a preferred and validated sampling method. However, when volatile furan precursors are adsorbed on the carboxen/PDMS fiber, additional amounts of furan can be formed on the fiber during thermal desorption, as shown here for 2-butenal and furfural. No significant increase in furan amounts was found upon heating the furan precursor 2-butenal, indicating that the furan amounts formed during precursor heating experiments are negligible as compared to the additional amounts of furan formed during fiber desorption. This artefactual furan formation increased with increasing desorption time, but especially with increasing desorption temperature. Although this effect was most pronounced on the Carboxen/PDMS SPME-fiber, it was also noted on two other SPME-fibers tested (PDMS and DVB/Carboxen/PDMS). The general impact on furan data from food and model systems in literature will depend on the amounts of volatile precursors present, but will probably remain limited. However, considering the importance of this worldwide food contaminant, special care has to be taken during SPME-analysis of furan. Especially when performing precursor studies, static headspace sampling should preferably be applied for furan analysis. Copyright © 2012 Elsevier B.V. All rights reserved.

Operation of low-noise single-gap RPC modules exposed to ionisation rates up to 1 kHz /cm2

NASA Astrophysics Data System (ADS)

Ćwiok, M.; Dominik, W.; Górski, M.; Królikowski, J.

2004-11-01

Two single gap medium-size RPC modules, made of bakelite plates of very good mechanical quality of the surface and having initial volume resistivity of 1 ×1010 Ω cm, were tested in the Gamma Irradiation Facility at CERN at ionisation rates up to 1 kHz /cm2. The internal surfaces facing the gas volume of one RPC module were cladded with a thin layer of linseed oil varnish for comparison of oiled and non-oiled RPC operation. The results refer to the gas mixture of C2H2F4/isobutane (97:3) with SF6 addition below 1%. The single gap modules exhibited full detection efficiency plateau for the high voltage range of about 1 kV at full intensity of gamma rays. Good timing characteristics allowed to reach 95% efficiency at fully opened irradiation source with time window of 20 ns. The intrinsic noise rate for a non-oiled and an oiled RPC gap was, respectively, below 5 and 1 Hz /cm2 at full efficiency over 1 kV voltage range.

Vibrations At Surfaces During Heterogeneous Catalytic Reactions

NASA Astrophysics Data System (ADS)

Aragno, A.; Basini, Luca; Marchionna, M.; Raffaelli, A.

1989-12-01

FTIR spectroscopies can be used in a wide range of temperature and pressure conditions to investigate on the chemistry and the physics of heterogeneous catalytic reactions. In this paper we have shortly discussed the spectroscopic results obtained during the study of two different reactions; the skeletal isomerization of 1-butene to obtain 2-methylpropene and the surface aggregation and fragmentation of rhodium carbonyl complexes during thermal treatments in N2, H2, CO, CH4 atmospheres. In the first case high temperature proton tran-sfer reactions are proposed to be responsible for the skeletal isomerization reaction. In the second case our experiments have shown a partial reversibility of the nucleation processes at the surfaces and revealed a low temperature reactivity of methane on rhodium car-bonyl surface complexes.

Phase equilibrium measurements on nine binary mixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilding, W.V.; Giles, N.F.; Wilson, L.C.

1996-11-01

Phase equilibrium measurements have been performed on nine binary mixtures. The PTx method was used to obtain vapor-liquid equilibrium data for the following systems at two temperatures each: (aminoethyl)piperazine + diethylenetriamine; 2-butoxyethyl acetate + 2-butoxyethanol; 2-methyl-2-propanol + 2-methylbutane; 2-methyl-2-propanol + 2-methyl-2-butene; methacrylonitrile + methanol; 1-chloro-1,1-difluoroethane + hydrogen chloride; 2-(hexyloxy)ethanol + ethylene glycol; butane + ammonia; propionaldehyde + butane. Equilibrium vapor and liquid phase compositions were derived form the PTx data using the Soave equation of state to represent the vapor phase and the Wilson or the NRTL activity coefficient model to represent the liquid phase. A large immiscibility region existsmore » in the butane + ammonia system at 0 C. Therefore, separate vapor-liquid-liquid equilibrium measurements were performed on this system to more precisely determine the miscibility limits and the composition of the vapor phase in equilibrium with the two liquid phases.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Dong; Xu, Pinghong; Browning, Nigel D.

The initial steps of rhodium cluster formation from zeolite-supported mononuclear Rh(C2H4)2 complexes in H2 at 373 K and 1 bar were investigated by infrared and extended X-ray absorption fine structure spectroscopies and scanning transmission electron microscopy (STEM). The data show that ethylene ligands on the rhodium react with H2 to give supported rhodium hydrides and trigger the formation of rhodium clusters. STEM provided the first images of the smallest rhodium clusters (Rh2) and their further conversion into larger clusters. The samples were investigated in a plug-flow reactor as catalysts for the conversion of ethylene + H2 in a molar ratiomore » of 4:1 at 1 bar and 298 K, with the results showing how the changes in catalyst structure affect the activity and selectivity; the rhodium clusters are more active for hydrogenation of ethylene than the single-site complexes, which are more selective for dimerization of ethylene to give butenes« less

Histrionicotoxins: Roentgen-Ray Analysis of the Novel Allenic and Acetylenic Spiroalkaloids Isolated from a Colombian Frog, Dendrobates histrionicus

PubMed Central

Daly, John W.; Karle, Isabella; Myers, Charles W.; Tokuyama, Takashi; Waters, James A.; Witkop, Bernhard

1971-01-01

The structures and absolute configuration of two unique alkaloids isolated from the Colombian frog, Dendrobates histrionicus, have been elucidated by Roentgen-ray (x-ray) crystallography. Histrionicotoxin is (2pR, 6S, 7pS, 8aS)-7-(cis-1-buten-3-ynyl)-8-hydroxy-2-(cis-2-penten-4- ynyl)-1-azaspiro[5.5] undecane, while in dihydro-isohistrionicotoxin the acetylenic 2-pentenynyl side chain is replaced by an allenic 2-(3,4 pentadienyl) substituent. Dendrobates histrionicus exhibits remarkable interpopulational variations in amounts and composition of skin toxins, in behavior, and in phenotypic characters, aspects of which are illustrated in a color plate. The histrionico-toxins are the third class of alkaloids isolated from the defensive skin secretions of Neotropical (Dendrobatidae) frogs. Images PMID:5288773

Sustainable Pathways to Pyrroles through Iron-Catalyzed N-Heterocyclization from Unsaturated Diols and Primary Amines.

PubMed

Yan, Tao; Barta, Katalin

2016-09-08

Pyrroles are prominent scaffolds in pharmaceutically active compounds and play an important role in medicinal chemistry. Therefore, the development of new, atom-economic, and sustainable catalytic strategies to obtain these moieties is highly desired. Direct catalytic pathways that utilize readily available alcohol substrates have been recently established; however, these approaches rely on the use of noble metals such as ruthenium or iridium. Here, we report on the direct synthesis of pyrroles using a catalyst based on the earth-abundant and inexpensive iron. The method uses 2-butyne-1,4-diol or 2-butene-1,4-diol that can be directly coupled with anilines, benzyl amines, and aliphatic amines to obtain a variety of N-substituted pyrroles in moderate-to-excellent isolated yields. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A selected ion flow tube study of the reactions of H3O+, NO+ and O2+ with some oxygenated biogenic volatile organic compounds

NASA Astrophysics Data System (ADS)

Amelynck, C.; Schoon, N.; Kuppens, T.; Bultinck, P.; Arijs, E.

2005-12-01

The rate constants and product ion distributions of the reactions of H3O+, NO+ and O2+ with 2-methyl-3-buten-2-ol, cis-3-hexen-1-ol, cis-3-hexenyl acetate, 1,8-cineole, 6-methyl-5-hepten-2-one, camphor and linalool have been determined at 150 Pa and 297 K using a selected ion flow tube (SIFT). All reactions were found to proceed at a rate close to the collision rate, calculated with the Su and Chesnavich model, using the polarizability and electric dipole moment of the compounds derived from B3LYP/aug-cc-pVDZ quantum chemical calculations. Additionally the product ion distributions of the reactions of these three ions with the terpenoid alcohols nerol and geraniol have been obtained.

Microbial removal of alkanes from dilute gaseous waste streams: kinetics and mass transfer considerations.

PubMed

Barton, J W; Klasson, K T; Koran, L J; Davison, B H

1997-01-01

Treatment of dilute gaseous hydrocarbon waste streams remains a current need for many industries, particularly as increasingly stringent environmental regulations and oversight force emission reduction. Biofiltration systems hold promise for providing low-cost alternatives to more traditional, energy-intensive treatment methods such as incineration and adsorption. Elucidation of engineering principles governing the behavior of such systems, including mass transfer limitations, will broaden their applicability. Our processes exploit a microbial consortium to treat a mixture of 0.5% n-pentane and 0.5% isobutane in air. Since hydrocarbon gases are sparingly soluble in water, good mixing and high surface area between the gas and liquid phases are essential for biodegradation to be effective. One liquid-continuous columnar bioreactor was operated for more than 30 months with continued degradation of n-pentane and isobutane as sole carbon and energy sources. The maximum degradation rate observed in this gas-recycle system was 2 g of volatile organic compounds (VOC)/(m3.h). A trickle-bed bioreactor was operated continuously for over 24 months to provide a higher surface area (using a structured packing) with increased rates. Degradation rates consistently achieved were approximately 50 g of VOC/(m3.h) via single pass in this gas-continuous columnar system. Effective mass transfer coefficients comparable to literature values were also measured for this reactor; these values were substantially higher than those found in the gas-recycle reactor. Control of biomass levels was implemented by limiting the level of available nitrogen in the recirculating aqueous media, enabling long-term stability of reactor performance.

Monitoring CO2 emissions in tree kill areas near the resurgent dome at Long Valley Caldera, California

USGS Publications Warehouse

Bergfeld, D.; Evans, William C.

2011-01-01

We report results of yearly measurements of the diffuse CO2 flux and shallow soil temperatures collected since 2006 across two sets of tree-kill areas at Long Valley Caldera, California. These data provide background information about CO2 discharge during a period with moderate seismicity, but little to no deformation. The tree kills are located at long-recognized areas of weak thermal fluid upflow, but have expanded in recent years, possibly in response to geothermal fluid production at Casa Diablo. The amount of CO2 discharged from the older kill area at Basalt Canyon is fairly constant and is around 3-5 tonnes of CO2 per day from an area of about 15,000 m2. The presence of isobutane in gas samples from sites in and around Basalt Canyon suggests that geothermal fluid production directly effects fluid upflow in the region close to the power plant. The average fluxes at Shady Rest are lower than average fluxes at Basalt Canyon, but the area affected by fluid upflow is larger. Total CO2 discharged from the central portion of the kill area at Shady Rest has been variable, ranging from 6 to11 tonnes per day across 61,000 m2. Gas collected at Shady Rest contains no detectable isobutane to link emissions chemically to geothermal fluid production, but two samples from 2009-10 have detectable H2S and suggest an increasing geothermal character of emitted gas. The appearance of this gas at the surface may signal increased drawdown of water levels near the geothermal productions wells.

40 CFR 1065.720 - Liquefied petroleum gas.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., C3H8 Minimum, 0.85 m3/m3 ASTM D2163-05. Vapor pressure at 38 °C Maximum, 1400 kPa ASTM D1267-02 or 2598-022. Volatility residue (evaporated temperature, 35 °C) Maximum, −38 °C ASTM D1837-02a. Butanes Maximum, 0.05 m3/m3 ASTM D2163-05. Butenes Maximum, 0.02 m3/m3 ASTM D2163-05. Pentenes and heavier Maximum...

Sonolysis of hydrocarbons in aqueous solution

NASA Astrophysics Data System (ADS)

Hart, Edwin J.; Fischer, Christian-Herbert; Henglein, Arnim

Water was irradiated with 300 kHz ultrasound under an argon atmosphere containing various amounts of methane and ethane. Limited studies were also made on ethylene, acetylene, propane and butane. The methane and ethane irradiations were carried out over the hydrocarbon-argon range of 2-100%. Maximum decomposition occurs at 15% for methane and 10% for ethane. While hydrogen is a dominant product in both cases, acetylene, ethylene and ethane are prominent products, too. Propane, propene and propin form in lesser quantities. 2-methyl-propane, n-butane, l-butene, 2-methyl-butene, butadiene and n-butin have also been identified. These hydrocarbons are similar to those found in pyrolysis and in fuel rich combustion experiments. Carbon monoxide is an important product at hydrocarbon concentrations less than 40% establishing water was an oxygen delivering reactant under these conditions. In the case of methane, the ratio of ethylene plus acetylene to ethane is used to estimate the effective temperature in the cavitation bubble. A temperature of about 2800 K is obtained for bubbles containing argon (plus water vapor and 20% CH 4) and T = 2000 K for pure methane. The rate of decomposition for unsaturated hydrocarbons is substantially greater than for the saturated ones. Low molecular weight products are mainly formed from saturated hydrocarbons whereas polymerization products are mainly formed from the unsaturated hydrocarbons. The decomposition of acetylene in argon bubbles is one of the fastest sonolytic processes.

Quantum chemical modeling of zeolite-catalyzed methylation reactions: toward chemical accuracy for barriers.

PubMed

Svelle, Stian; Tuma, Christian; Rozanska, Xavier; Kerber, Torsten; Sauer, Joachim

2009-01-21

The methylation of ethene, propene, and t-2-butene by methanol over the acidic microporous H-ZSM-5 catalyst has been investigated by a range of computational methods. Density functional theory (DFT) with periodic boundary conditions (PBE functional) fails to describe the experimentally determined decrease of apparent energy barriers with the alkene size due to inadequate description of dispersion forces. Adding a damped dispersion term expressed as a parametrized sum over atom pair C(6) contributions leads to uniformly underestimated barriers due to self-interaction errors. A hybrid MP2:DFT scheme is presented that combines MP2 energy calculations on a series of cluster models of increasing size with periodic DFT calculations, which allows extrapolation to the periodic MP2 limit. Additionally, errors caused by the use of finite basis sets, contributions of higher order correlation effects, zero-point vibrational energy, and thermal contributions to the enthalpy were evaluated and added to the "periodic" MP2 estimate. This multistep approach leads to enthalpy barriers at 623 K of 104, 77, and 48 kJ/mol for ethene, propene, and t-2-butene, respectively, which deviate from the experimentally measured values by 0, +13, and +8 kJ/mol. Hence, enthalpy barriers can be calculated with near chemical accuracy, which constitutes significant progress in the quantum chemical modeling of reactions in heterogeneous catalysis in general and microporous zeolites in particular.

Structural and physicochemical studies of two key intermediates and the impurity in the new synthesis route of vitamin MK-7

NASA Astrophysics Data System (ADS)

Łaszcz, Marta; Trzcińska, Kinga; Kubiszewski, Marek; Krajewski, Krzysztof

2018-05-01

The MK-7 homologues of vitamin K2 are characterized by the best bioavailability among other K vitamins and act effectively in the treatment of osteoporosis and cardiovascular diseases. In this article comprehensive structural studies of two intermediates 1,4-diethoxy-2-methylnaphtalene (M2) and 1,4-diethoxy-2-methyl-3-[(2E)-3-methyl-4-(phenylsulfonyl)-2-buten-1-yl]naphtalene (M3) from the multi-step synthesis of MK-7 vitamin were described. The compounds crystallize in a monoclinic system in P21/n and P21/c for M2 and M3, respectively. Also, the isomer (2E)-4-chloro-3-methyl-1-(phenylsulfonyl)but-2-ene (M1-E verso) was isolated and the single crystal studies were performed. These three compounds were fully characterized by the 1D and 2D NMR technique as well as by Fourier-transformed infrared and Raman spectroscopies.

Energy dependent features of X-ray signals in a GridPix detector

NASA Astrophysics Data System (ADS)

Krieger, C.; Kaminski, J.; Vafeiadis, T.; Desch, K.

2018-06-01

We report on the calibration of an argon/isobutane (97.7%/2.3%)-filled GridPix detector with soft X-rays (277 eV to 8 keV) using the variable energy X-ray source of the CAST Detector Lab at CERN. We study the linearity and energy resolution of the detector using both the number of pixels hit and the total measured charge as energy measures. For the latter, the energy resolution σE / E is better than 10% (20%) for energies above 2 keV (0.5 keV). Several characteristics of the recorded events are studied.

STATEQ: a nonlinear least-squares code for obtaining Martin thermodynamic representations of fluids in the gaseous and dense gaseous regions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milora, S. L.

1976-02-01

The use of the code NLIN (IBM Share Program No. 1428) to obtain empirical thermodynamic pressure-volume-temperature (P-V-T) relationships for substances in the gaseous and dense gaseous states is described. When sufficient experimental data exist, the code STATEQ will provide least-squares estimates for the 21 parameters of the Martin model. Another code, APPROX, is described which also obtains parameter estimates for the model by making use of the approximate generalized behavior of fluids. Use of the codes is illustrated in obtaining thermodynamic representations for isobutane. (auth)

Melting of superheated molecular crystals

NASA Astrophysics Data System (ADS)

Cubeta, Ulyana; Bhattacharya, Deepanjan; Sadtchenko, Vlad

2017-07-01

Melting dynamics of micrometer scale, polycrystalline samples of isobutane, dimethyl ether, methyl benzene, and 2-propanol were investigated by fast scanning calorimetry. When films are superheated with rates in excess of 105 K s-1, the melting process follows zero-order, Arrhenius-like kinetics until approximately half of the sample has transformed. Such kinetics strongly imply that melting progresses into the bulk via a rapidly moving solid-liquid interface that is likely to originate at the sample's surface. Remarkably, the apparent activation energies for the phase transformation are large; all exceed the enthalpy of vaporization of each compound and some exceed it by an order of magnitude. In fact, we find that the crystalline melting kinetics are comparable to the kinetics of dielectric α-relaxation in deeply supercooled liquids. Based on these observations, we conclude that the rate of non-isothermal melting for superheated, low-molecular-weight crystals is limited by constituent diffusion into an abnormally dense, glass-like, non-crystalline phase.

Field tests of 2- and 40-tube condensers at the East Mesa Geothermal Test Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murphy, R.W.; Domingo, N.

1982-05-01

Two water-cooled isobutane condensers, one with 2 tubes and one with 40 tubes, were subjected to field tests at the East Mesa Geothermal Test Site to assess relative heat transfer performance in both surface evaporator and direct-contact evaporator modes. The five groups of tests established that field performance was below earlier laboratory-determined levels and that direct-contact evaporator mode performance was poorer than that for the surface evaporator mode. In all test situations, fluted condenser tubes performed better than smooth condenser tubes. Cooling water quality had no significant effect on performance, but brine preflash in the direct-contact mode did promote somemore » relative performance improvement. Important implications of these results for binary geothermal power plants are that (1) working-fluid-side impurities can significantly degrade heat transfer performance of the power plant condensers and (2) provisions for minimizing such impurities may be required.« less

Synthesis of butenes through 2-butanol dehydration over mesoporous materials produced from ferrierite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeong, Soyeon; Kim, Hyeonjoo; Bae, Jung A.

2012-05-20

Mesoporous materials synthesized from commercial ferrierite (MMZ-FER) were applied to butanol dehydration. The MMZ-FER was produced by disassembling ferrierite into unit structures in the presence of an alkali solution, adding a surfactant as a templating material, followed by hydrothermal treatment. The effect of the alkali/(Si+Al) ratio in the disassembling step on the characteristics of the catalyst and butanol dehydration performance were investigated. The MMZ-FER materials, synthesized in a condition in which the NaOH/(Si + Al) mole ratio in the disassembling step was 0.67 and 1.0, demonstrated similar textural properties to those of MCM-41. Many weak acid sites developed on themore » MMZ-FER(0.67) and MMZ-FER(1.0) samples, which is attributed to the creation of ferrierite-induced acid sites. The MMZ-FER materials showed excellent catalytic activity, selectivity, and stability during the dehydration of 2-butanol.« less

1996 PAMS hydrocarbon QA studies in EPA Region II: Part II. Trends and insights

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teitz, A.; Kantz, M.

1997-12-31

Comparison of ambient air samples between EPA Region II and the PAMS monitoring organizations within the Region, and comparisons among EPA Regions I, II, and III, revealed the following analytical trends: (1) Agreement between laboratories was typically between 10-20% for many of the PAMS analytes found at higher concentrations, i.e., butane, isopentane, benzene, toluene, and m/p-xylene; (2) Nafion dryer systems tended to underestimate the amount of acetylene by 35-50%; (3) Isobutylene co-elution with 1-butene proved difficult to resolve unless a 100 meter DB-1 or a regular length PLOT GC column was used; (4) Organizations that monitor for polar compounds foundmore » that co-elution of ethanol/acetone can interfere with the analysis of 1-pentene; (5) Analytical systems capable of polar analyses can have co-elution and/or misidentification of these aldehydes, typically in the styrene/heptanal/o-xylene regions of the chromatogram; and (6) Tetrachloroethylene was found to interfere with octane quantitation in some analyses.« less

Degradation of isobutanal at high loading rates in a compost biofilter.

PubMed

Sercu, Bram; Demeestere, Kristof; Baillieul, Hans; Van Langenhove, Herman; Verstraete, Willy

2005-08-01

Biofiltration has been increasingly used for cleaning waste gases, mostly containing low concentrations of odorous compounds. To expand the application area of this technology, the biofiltration of higher pollutant loading rates has to be investigated. This article focuses on the biodegradation of isobutanal (IBAL) in a compost biofilter (BF) at mass loading rates between 211 and 4123 g/m3/day (30-590 ppm(v)). At mass loading rates up to 785 g/m3/day, near 100% removal efficiencies could be obtained. However, after increasing the loading rate to 1500-1900 g/m3/ day, the degradation efficiency decreased to 62-98%. In addition, a pH decrease and production of isobutanol (IBOL) and isobutyric acid (IBAC) were observed. This is the first report showing that an aldehyde can act as electron donor as well as acceptor in a BF. To study the effects of pH, compost moisture content, and electron acceptor availability on the biofiltration of IBAL, IBOL, and IBAC, additional batch and continuous experiments were performed. A pH of 5.2 reduced the IBAL degradation rate and inhibited the IBOL degradation, although adaptation of the microorganisms to low pH was observed in the BFs. IBAC was not degraded in the batch experiments. High moisture content (51%) initially had no effect on the IBOL production, although it negatively affected the IBAL elimination increasingly during a 21-day time-course experiment. In batch experiments, the reduction of IBAL to IBOL did not decrease when the amount of available electron acceptors (oxygen or nitrate) was increased. The IBAL removal efficiency at higher loading rates was limited by a combination of nutrient limitation, pH decrease, and dehydration, and the importance of each limiting factor depended on the influent concentration.

Molecular dynamics averaging of Xe chemical shifts in liquids.

PubMed

Jameson, Cynthia J; Sears, Devin N; Murad, Sohail

2004-11-15

The Xe nuclear magnetic resonance chemical shift differences that afford the discrimination between various biological environments are of current interest for biosensor applications and medical diagnostic purposes. In many such environments the Xe signal appears close to that in water. We calculate average Xe chemical shifts (relative to the free Xe atom) in solution in eleven liquids: water, isobutane, perfluoro-isobutane, n-butane, n-pentane, neopentane, perfluoroneopentane, n-hexane, n-octane, n-perfluorooctane, and perfluorooctyl bromide. The latter is a liquid used for intravenous Xe delivery. We calculate quantum mechanically the Xe shielding response in Xe-molecule van der Waals complexes, from which calculations we develop Xe (atomic site) interpolating functions that reproduce the ab initio Xe shielding response in the complex. By assuming additivity, these Xe-site shielding functions can be used to calculate the shielding for any configuration of such molecules around Xe. The averaging over configurations is done via molecular dynamics (MD). The simulations were carried out using a MD technique that one of us had developed previously for the simulation of Henry's constants of gases dissolved in liquids. It is based on separating a gaseous compartment in the MD system from the solvent using a semipermeable membrane that is permeable only to the gas molecules. We reproduce the experimental trends in the Xe chemical shifts in n-alkanes with increasing number of carbons and the large chemical shift difference between Xe in water and in perfluorooctyl bromide. We also reproduce the trend for a given solvent of decreasing Xe chemical shift with increasing temperature. We predict chemical shift differences between Xe in alkanes vs their perfluoro counterparts.

Characterization of hydrocarbons, halocarbons and carbonyls in the atmosphere of Hong Kong.

PubMed

Guo, H; Lee, S C; Louie, P K K; Ho, K F

2004-12-01

Ambient air quality measurements of 156 species including 39 alkanes, 32 alkenes, 2 alkynes, 24 aromatic hydrocarbons, 43 halocarbons and 16 carbonyls, were carried out for 120 air samples collected at two sampling stations (CW and TW) in 2001 throughout Hong Kong. Spatial variations of volatile organic compounds (VOCs) in the atmosphere were investigated. Levels of most alkanes and alkenes at TW site were higher than that at the CW site, while the BTEX concentrations at the two sites were close. The BTEX ratios at CW and TW were 1.6:10.1:1.0:1.6 and 2.1:10.8:1.0:2.0, respectively. For major halogenated hydrocarbons, the mean concentrations of chloromethane, CFCs 12 and 22 did not show spatial variations at the two sites. However, site-specific differences were observed for trichloroethene and tetrachloroethene. Furthermore, there were no significant differences for carbonyls such as formaldehyde, acetaldehyde and acetone between the two sites. The levels of selected hydrocarbons in winter were 1-5 times that in summer. There were no common seasonal trends for carbonyls in Hong Kong. The ambient level of formaldehyde, the most abundant carbonyl, was higher in summer. However, levels of acetaldehyde, acetone and benzaldehyde in winter were 1.6-3.8 times that in summer. The levels of CFCs 11 and 12, and chloromethane in summer were higher than that in winter. Strong correlation of most hydrocarbons with propene and n-butane suggested that the primary contributors of hydrocarbons were vehicular emissions in Hong Kong. In addition, gasoline evaporation, use of solvents, leakage of liquefied petroleum gas (LPG), natural gas leakage and other industrial emissions, and even biogenic emissions affected the ambient levels of hydrocarbons. The sources of halocarbons were mainly materials used in industrial processes and as solvents. Correlation analysis suggested that photochemical reactions made significant contributions to the ambient levels of carbonyls in summer whereas in winter motor vehicle emissions would be the major sources of the carbonyls. The photochemical reactivity of selected VOCs was estimated in this study. The largest contributors to ozone formation were formaldehyde, toluene, propene, m,p-xylene, acetaldehyde, 1-butene/i-butene, isoprene and n-butane, suggesting that motor vehicles, gasoline evaporation, use of solvents, leakage of LPG, photochemical processes and biogenic emission are sources in the production of ozone. On the other hand, VOCs from vehicles and gasoline evaporation were predominant with respect to reactions with OH radical.

Two unexpected promiscuous activities of the iron-sulfur protein IspH in production of isoprene and isoamylene.

PubMed

Ge, Deyong; Xue, Yanfen; Ma, Yanhe

2016-05-11

Bacillus species, possessing the methylerythritol phosphate (MEP) pathway for the synthesis of isoprenoid feedstock, are the highest producers of isoprene among bacteria; however, the enzyme responsible for isoprene synthesis has not been identified. The iron-sulfur protein IspH is the final enzyme of the MEP pathway and catalyses the reductive dehydration of (E)-4-hydroxy-3-methyl-2-butenyl diphosphate (HMBPP) to form isopentenyl diphosphate and dimethylallyl diphosphate (DMAPP). In this study, we demonstrated two unexpected promiscuous activities of IspH from alkaliphilic Bacillus sp. N16-5, which can produce high levels of isoprene. Bacillus sp. N16-5 IspH could catalyse the formation of isoprene from HMBPP and the conversion of DMAPP into a mixture of 2-methyl-2-butene and 3-methyl-1-butene. Both reactions require an electron transfer system, such as that used for HMBPP dehydration. Isoprene and isoamylene synthesis in Bacillus sp. N16-5 was investigated and the reaction system was reconstituted in vitro, including IspH, ferredoxin and ferredoxin-NADP(+)-reductase proteins and NADPH. The roles of specific IspH protein residues were also investigated by site-directed mutagenesis experiments; two variants (H131N and E133Q) were found to have lost the HMBPP reductase activity but could still catalyse the formation of isoprene. Overexpression of IspH H131N in Bacillus sp. N16-5 resulted in a twofold enhancement of isoprene production, and the yield of isoprene from the strain expressing E133Q was increased 300% compared with the wild-type strain. IspH from Bacillus sp. N16-5 is a promiscuous enzyme that can catalyse formation of isoprene and isoamylene. This enzyme, especially the H131N and E133Q variants, could be used for the production of isoprene from HMBPP.

Spectral signatures for RDX-based explosives in the 3 micron region

NASA Astrophysics Data System (ADS)

Osborn, Tabetha; Kaimal, Sindhu; Reeve, Scott W.; Burns, William

2008-04-01

Explosive compounds such as RDX, and HMX present significant challenges to optically based sensors. This difficulty is due in part to the low vapor pressures these compounds possess. One approach for sensing explosives that circumvents the low explosive vapor pressure problem, involves focusing on the trace amounts of relatively high vapor pressure impurities that will be present in the vapor signature. In order to effectively detect these volatile impurities, the spectral signature databases must be readily available. One of our goals therefore, is the generation of a database of high resolution spectral signatures for these volatile organic impurities. Some rather formidable spectroscopic measurement challenges have been encountered while working to extend the spectral signature effort to the 3 micron region. Here we will outline progress to date, with a focus on the volatile organic compounds formaldehyde, acetaldehyde, nitromethane, acetone, isobutene, and cyclohexanone.

Total cross sections for ultracold neutrons scattered from gases

DOE PAGES

Seestrom, Susan Joyce; Adamek, Evan R.; Barlow, Dave; ...

2017-01-30

Here, we have followed up on our previous measurements of upscattering of ultracold neutrons (UCNs) from a series of gases by making measurements of total cross sections on the following gases hydrogen, ethane, methane, isobutene, n-butane, ethylene, water vapor, propane, neopentane, isopropyl alcohol, and 3He. The values of these cross sections are important for estimating the loss rate of trapped neutrons due to residual gas and are relevant to neutron lifetime measurements using UCNs. The effects of the UCN velocity and path-length distributions were accounted for in the analysis using a Monte Carlo transport code. Results are compared to ourmore » previous measurements and with the known absorption cross section for 3He scaled to our UCN energy. We find that the total cross sections for the hydrocarbon gases are reasonably described by a function linear in the number of hydrogen atoms in the molecule.« less

Fire extinguishing tests -80 with methyl alcohol gasoline

NASA Astrophysics Data System (ADS)

Holmstedt, G.; Ryderman, A.; Carlsson, B.; Lennmalm, B.

1980-10-01

Large scale tests and laboratory experiments were carried out for estimating the extinguishing effectiveness of three alcohol resistant aqueous film forming foams (AFFF), two alcohol resistant fluoroprotein foams and two detergent foams in various poolfires: gasoline, isopropyl alcohol, acetone, methyl-ethyl ketone, methyl alcohol and M15 (a gasoline, methyl alcohol, isobutene mixture). The scaling down of large scale tests for developing a reliable laboratory method was especially examined. The tests were performed with semidirect foam application, in pools of 50, 11, 4, 0.6, and 0.25 sq m. Burning time, temperature distribution in the liquid, and thermal radiation were determined. An M15 fire can be extinguished with a detergent foam, but it is impossible to extinguish fires in polar solvents, such as methyl alcohol, acetone, and isopropyl alcohol with detergent foams, AFFF give the best results; and performances with small pools can hardly be correlated with results from large scale fires.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seestrom, Susan Joyce; Adamek, Evan R.; Barlow, Dave

Here, we have followed up on our previous measurements of upscattering of ultracold neutrons (UCNs) from a series of gases by making measurements of total cross sections on the following gases hydrogen, ethane, methane, isobutene, n-butane, ethylene, water vapor, propane, neopentane, isopropyl alcohol, and 3He. The values of these cross sections are important for estimating the loss rate of trapped neutrons due to residual gas and are relevant to neutron lifetime measurements using UCNs. The effects of the UCN velocity and path-length distributions were accounted for in the analysis using a Monte Carlo transport code. Results are compared to ourmore » previous measurements and with the known absorption cross section for 3He scaled to our UCN energy. We find that the total cross sections for the hydrocarbon gases are reasonably described by a function linear in the number of hydrogen atoms in the molecule.« less

Selective hydrogenation of 1,3-butadiene on platinum–copper alloys at the single-atom limit

DOE PAGES

Lucci, Felicia R.; Liu, Jilei; Marcinkowski, Matthew D.; ...

2015-10-09

Platinum is ubiquitous in the production sectors of chemicals and fuels; however, its scarcity in nature and high price will limit future proliferation of platinum-catalysed reactions. One definite approach to conserve platinum involves understanding the smallest number of platinum atoms needed to catalyse a reaction, then designing catalysts with the minimal platinum ensembles. Here we design and test a new generation of platinum–copper nanoparticle catalysts for the selective hydrogenation of 1,3-butadiene,, an industrially important reaction. Isolated platinum atom geometries enable hydrogen activation and spillover but are incapable of C–C bond scission that leads to loss of selectivity and catalyst deactivation.more » γ-Alumina-supported single-atom alloy nanoparticle catalysts with <1 platinum atom per 100 copper atoms are found to exhibit high activity and selectivity for butadiene hydrogenation to butenes under mild conditions, demonstrating transferability from the model study to the catalytic reaction under practical conditions.« less

Vitamin B1-catalyzed acetoin formation from acetaldehyde: a key step for upgrading bioethanol to bulk C₄ chemicals.

PubMed

Lu, Ting; Li, Xiukai; Gu, Liuqun; Zhang, Yugen

2014-09-01

The production of bulk chemicals and fuels from renewable biobased feedstocks is of significant importance for the sustainability of human society. The production of ethanol from biomass has dramatically increased and bioethanol also holds considerable potential as a versatile building block for the chemical industry. Herein, we report a highly selective process for the conversion of ethanol to C4 bulk chemicals, such as 2,3-butanediol and butene, via a vitamin B1 (thiamine)-derived N-heterocyclic carbene (NHC)-catalyzed acetoin condensation as the key step to assemble two C2 acetaldehydes into a C4 product. The environmentally benign and cheap natural catalyst vitamin B1 demonstrates high selectivity (99%), high efficiency (97% yield), and high tolerance toward ethanol and water impurities in the acetoin reaction. The results enable a novel and efficient process for ethanol upgrading. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Production of high current proton beams using complex H-rich molecules at GSI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adonin, A., E-mail: a.adonin@gsi.de; Barth, W.; Heymach, F.

2016-02-15

In this contribution, the concept of production of intense proton beams using molecular heavy ion beams from an ion source is described, as well as the indisputable advantages of this technique for operation of the GSI linear accelerator. The results of experimental investigations, including mass-spectra analysis and beam emittance measurements, with different ion beams (CH{sub 3}{sup +},C{sub 2}H{sub 4}{sup +},C{sub 3}H{sub 7}{sup +}) using various gaseous and liquid substances (methane, ethane, propane, isobutane, and iodoethane) at the ion source are summarized. Further steps to improve the ion source and injector performance with molecular beams are depicted.

Applications of the Soave-Redlich-Kwong Equations of State Using Mathematic

NASA Astrophysics Data System (ADS)

Sun, Lanyi; Zhai, Cheng; Zhang, Hui

The application of the Peng-Robinson equations of state (PR EOS) using Matlab and Mathematic has already been demonstrated. In this paper, using Mathematic to solve Soave-Redlich-Kwong (SRK) EOS, as well as the estimation of pure component properties, plotting of vapor-liquid equilibrium (VLE) diagram and calculation of chemical equilibrium, is presented. First the SRK EOS is used to predict several pure-component properties, such as liquid and gas molar volumes for isobutane. The vapor-liquid isobaric diagram is then plotted for a binary mixture composed of n-pentane and n-hexane under the pressures of 2*10^5 and 8*10^5 Pa respectively.

Cytotoxic and Antimicrobial Activity of Dehydrozingerone based Cyclopropyl Derivatives.

PubMed

Burmudžija, Adrijana Z; Muškinja, Jovana M; Kosanić, Marijana M; Ranković, Branislav R; Novaković, Slađana B; Đorđević, Snežana B; Stanojković, Tatjana P; Baskić, Dejan D; Ratković, Zoran R

2017-08-01

A small series of 1-acetyl-2-(4-alkoxy-3-methoxyphenyl)cyclopropanes was prepared, starting from dehydrozingerone (4-(4-hydroxy-3-methoxyphenyl)-3-buten-2-one) and its O-alkyl derivatives. Their microbiological activities toward some strains of bacteria and fungi were tested, as well as their in vitro cytotoxic activity against some cancer cell lines (HeLa, LS174 and A549). All synthesized compounds showed significant antimicrobial activity and expressed cytotoxic activity against tested carcinoma cell lines, but they showed no significant influence on normal cell line (MRC5). Butyl derivative is the most active on HeLa cells (IC 50 = 8.63 μm), while benzyl one is active against LS174 and A549 cell lines (IC 50 = 10.17 and 12.15 μm, respectively). © 2017 Wiley-VHCA AG, Zurich, Switzerland.

Study of the Air-Tolerant 1,3-Diphosphacyclobutane-2,4-diyl through the Direct Arylation.

PubMed

Ito, Shigekazu

2018-04-01

Installing π-functional substituents on the skeletal phosphorus atoms of the air-tolerant 1,3-diphosphacyclobutane-2,4-diyl unit are promising for tuning the open-shell singlet P-heterocyclic chromophore. The sterically encumbered 1,3-diphosphaCycloButen-4-yl Anion (CBA), generated from the phosphorus-carbon triple bond, was available for the regioselective arylation via nucleophilic aromatic substitution (S N Ar) reaction, addition to arynes, and single-electron transfer (SET) process affording the corresponding P-arylated 1,3-diphosphacyclobutane-2,4-diyls. The photo-absorption and redox properties correlated with the effects of the aryl substituents on the 1,3-diphosphacyclobutane-2,4-diyl unit. The X-ray analyses enabled not only to discuss the metric parameters but also to visualize the radicalic electrons via the electron-density distribution analysis. The electron-donating character of the P-heterocyclic chromophores induced the p-type semiconductor behavior. Detection of hydrogen fluoride via formation of the 1λ 5 ,3λ 5 -diphosphete derivative was also developed. © 2018 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ethylene polymerization on a SiH4-modified Phillips catalyst: detection of in situ produced α-olefins by operando FT-IR spectroscopy.

PubMed

Barzan, Caterina; Groppo, Elena; Quadrelli, Elsje Alessandra; Monteil, Vincent; Bordiga, Silvia

2012-02-21

Ethylene polymerization on a model Cr(II)/SiO(2) Phillips catalyst modified with gas phase SiH(4) leads to a waxy product containing a bimodal MW distribution of α-olefins (M(w) < 3000 g mol(-1)) and a highly branched polyethylene, LLDPE (M(w) ≈ 10(5) g mol(-1), T(m) = 123 °C), contrary to the unmodified catalyst which gives a linear and more dense PE, HDPE (M(w) = 86,000 g mol(-1) (PDI = 7), T(m) = 134 °C). Pressure and temperature resolved FT-IR spectroscopy under operando conditions (T = 130-230 K) allows us to detect α-olefins, and in particular 1-hexene and 1-butene (characteristic IR absorption bands at 3581-3574, 1638 and 1598 cm(-1)) as intermediate species before their incorporation in the polymer chains. The polymerization rate is estimated, using time resolved FT-IR spectroscopy, to be 7 times higher on the SiH(4)-modified Phillips catalyst with respect to the unmodified one.

Tests for genotoxicity and mutagenicity of furan and its metabolite cis-2-butene-1,4-dial in L5178Y tk+/- mouse lymphoma cells.

PubMed

Kellert, Marco; Brink, Andreas; Richter, Ingrid; Schlatter, Josef; Lutz, Werner K

2008-12-08

Furan is found in various food items and is cytotoxic and carcinogenic in the liver of rats and mice. Metabolism of furan includes the formation of an unsaturated dialdehyde, cis-2-butene-1,4-dial (BDA). In view of the multifunctional electrophilic reactivity of BDA, adduct formation with protein and DNA may explain some of the toxic effects. Short-term tests for genotoxicity of furan in mammalian cells are inconclusive, little is known for BDA. We investigated BDA generated by hydrolysis of 2,5-diacetoxy-2,5-dihydrofuran for genotoxicity in L5178Y tk+/- mouse lymphoma cells using standard procedures for the comet assay, the micronucleus test, and the mouse lymphoma thymidine kinase gene mutation assay, using 4-h incubation periods. Cytotoxicity was remarkable: cell viability at concentrations>or=50 microM was reduced to <50%. In the dose range up to 25 microM, viability was >90%. Measures of comet-tail length and thymidine-kinase mutant frequency were increased 1.6- and 2.4-fold above control, respectively. Analysis of three fully independent replicates with a linear mixed-effects model showed a highly significant increase with concentration for both endpoints. Compared to methyl methanesulfonate used as a positive control, BDA was of similar potency with respect to genotoxicity, but it was much more cytotoxic. Furan added to cell cultures at doses that resulted in time-averaged effective concentrations of up to 3100 microM was neither cytotoxic nor genotoxic. A potential cross-linking activity of BDA was investigated by checking whether gamma radiation-induced DNA migration in the comet assay could be reduced by pre-treatment with BDA. In contrast to the effect of the positive control glutaraldehyde, BDA treatment did not reduce the comet tail length. On the contrary, an increase was observed at >or=100 microM BDA, which was attributable to early apoptotic cells. Although BDA was found to be a relatively potent genotoxic agent in terms of the concentration necessary to double the background measures, cytotoxicity strongly limited the concentration range that produced interpretable results. This may explain some of the inconclusive results and indicates that non-genotoxic effects must be taken into account in the discussion of the modes of toxic and carcinogenic action of furan.

On the temperature dependence of flammability limits of gases.

PubMed

Kondo, Shigeo; Takizawa, Kenji; Takahashi, Akifumi; Tokuhashi, Kazuaki

2011-03-15

Flammability limits of several combustible gases were measured at temperatures from 5 to 100 °C in a 12-l spherical flask basically following ASHRAE method. The measurements were done for methane, propane, isobutane, ethylene, propylene, dimethyl ether, methyl formate, 1,1-difluoroethane, ammonia, and carbon monoxide. As the temperature rises, the lower flammability limits are gradually shifted down and the upper limits are shifted up. Both the limits shift almost linearly to temperature within the range examined. The linear temperature dependence of the lower flammability limits is explained well using a limiting flame temperature concept at the lower concentration limit (LFL)--'White's rule'. The geometric mean of the flammability limits has been found to be relatively constant for many compounds over the temperature range studied (5-100 °C). Based on this fact, the temperature dependence of the upper flammability limit (UFL) can be predicted reasonably using the temperature coefficient calculated for the LFL. However, some compounds such as ethylene and dimethyl ether, in particular, have a more complex temperature dependence. Copyright © 2011 Elsevier B.V. All rights reserved.

Normal Mode Analysis in Zeolites: Toward an Efficient Calculation of Adsorption Entropies.

PubMed

De Moor, Bart A; Ghysels, An; Reyniers, Marie-Françoise; Van Speybroeck, Veronique; Waroquier, Michel; Marin, Guy B

2011-04-12

An efficient procedure for normal-mode analysis of extended systems, such as zeolites, is developed and illustrated for the physisorption and chemisorption of n-octane and isobutene in H-ZSM-22 and H-FAU using periodic DFT calculations employing the Vienna Ab Initio Simulation Package. Physisorption and chemisorption entropies resulting from partial Hessian vibrational analysis (PHVA) differ at most 10 J mol(-1) K(-1) from those resulting from full Hessian vibrational analysis, even for PHVA schemes in which only a very limited number of atoms are considered free. To acquire a well-conditioned Hessian, much tighter optimization criteria than commonly used for electronic energy calculations in zeolites are required, i.e., at least an energy cutoff of 400 eV, maximum force of 0.02 eV/Å, and self-consistent field loop convergence criteria of 10(-8) eV. For loosely bonded complexes the mobile adsorbate method is applied, in which frequency contributions originating from translational or rotational motions of the adsorbate are removed from the total partition function and replaced by free translational and/or rotational contributions. The frequencies corresponding with these translational and rotational modes can be selected unambiguously based on a mobile block Hessian-PHVA calculation, allowing the prediction of physisorption entropies within an accuracy of 10-15 J mol(-1) K(-1) as compared to experimental values. The approach presented in this study is useful for studies on other extended catalytic systems.

Shock tube study of the fuel structure effects on the chemical kinetic mechanisms responsible for soot formation, part 2

NASA Technical Reports Server (NTRS)

Frenklach, M.; Clary, D. W.; Ramachandra, M. K.

1985-01-01

Soot formation in oxidation of allene, 1,3-butadiene, vinylacetylene and chlorobenzene and in pyrolysis of ethylene, vinylacetylene, 1-butene, chlorobenzene, acetylen-hydrogen, benzene-acetylene, benzene-butadiene and chlorobenzene-acetylene argon-diluted mixtures was studied behind reflected shock waves. The results are rationalized within the framework of the conceptual models. It is shown that vinylacetylene is much less sooty than allene, which indicates that conjugation by itself is not a sufficient factor for determining the sooting tendency of a molecule. Structural reactivity in the context of the chemical kinetics is the dominant factor in soot formation. Detailed chemical kinetic modeling of soot formation in pyrolysis of acetylene is reported. The main mass growth was found to proceed through a single dominant route composed of conventional radical reactions. The practically irreversible formation reactions of the fused polycyclic aromatics and the overshoot by hydrogen atom over its equilibrium concentration are the g-driving kinetic forces for soot formation.

N,N′-Bis(3β-acet­oxy-5α-cholest-6-yl­idene)hydrazine

PubMed Central

Tabassum, Zishan; Sulaiman, Othman; Ibrahim, M. N. Mohamad; Quah, Ching Kheng; Fun, Hoong-Kun

2011-01-01

The asymmetric unit of the title compound, C58H96N2O4, contains two crystallographically independent mol­ecules. All cyclohexane rings are in chair conformations, while the furan ring is in an envelope conformation in one mol­ecule and a twist conformation in the other. Two acetaldehyde and one isobutane groups are disordered over two orientations with refined site occupancies of 0.940 (4):0.060 (4) and 0.791 (7):0.209 (7), respectively. In the crystal, mol­ecules are stacked along the a axis through van der Waals inter­actions. PMID:21523172

Synthesis of an un-supported, high-flow ZSM-22 zeolite membrane

DOEpatents

Thoma, Steven G [Albuquerque, NM; Nenoff, Tina M [Albuquerque, NM

2006-10-10

Novel methods for synthesizing wholly un-supported, high-flow catalytic membranes consisting of 100% crystalline ZSM-22 crystals with no binder phase, having sufficient porosity to allow high Weight Hourly Space Velocities of feedstock to pass through without generating back pressure. The ZSM-22 membranes perform favorably to existing bulk ZSM-22 catalysts (e.g., via 1-butene conversion and selectivity). The method of membrane synthesis, based on Vapor Phase Transport, allows free-standing, binder-less membranes to be fabricated in varied geometries and sizes so that membranes can be tailor-made for particular geometries applications. The ZSM-22 precursor gel may be consolidated into a semi-cohesive body prior to vapor phase crystallization, for example, by uniaxial pressing. These crystalline membranes may be modified by ion exchange, pore ion exchange, framework exchange, synthesis modification techniques to incorporate other elements into the framework, such as K, H, Mg, Zn, V, Ga, and Pt.

Development of segmented polyurethane elastomers with low iodine content exhibiting radiopacity and blood compatibility.

PubMed

Dawlee, S; Jayabalan, Muthu

2011-10-01

Biofunctionally active and inherently radiopaque polymers are the emerging need for biomedical applications. Novel segmented polyurethane elastomer with inherent radiopacity was prepared using aliphatic chain extender 2,3-diiodo-2-butene-1,4-diol, polyol polytetramethylene glycol and 4,4'-methylenebis(phenyl isocyanate) (MDI) for blood compatible applications. Aliphatic polyurethane was also prepared using hexamethylene diisocyanate for comparison. X-ray analysis of the polyurethanes revealed good radiopacity even at a relatively low concentration of 3% iodine in aromatic polyurethane and 10% in aliphatic polyurethane. The polyurethanes also possessed excellent thermal stability. MDI-based polyurethane showed considerably higher tensile strength than the analogous HDI-based polyurethane. MDI-based aromatic polyurethane exhibited a dynamic surface morphology in aqueous medium, resulting in the segregation of hydrophilic domains which was more conducive to anti-thrombogenic properties. The polyurethane was cytocompatible with L929 fibroblast cells, non-hemolytic, and possessed good blood compatibility.

[Studies on chemical components of essential oil of crude semen sinapis and roasted semen sinapis].

PubMed

Chen, Mi-Yu; Lin, Yan-Ni; Wu, Guo-Xin; Wu, Cui-Ping

2006-07-01

To study the chemical components of the essential oil of the Semen Sinapis with the different processing methods. The essential oils of the crude Semen Sinapis and the roasted Semen Sinapis were extracted by steam distillation. The chemical components were analyzed by means of GC-MS-DS. The relative content of each component was calculated by area normalization. The main chemical components of the essential oil of the crude Semen Sinapis and the roasted Semen Sinapis were similar. The main chemical components were allyl isothiocyanate and 4-isothio-cyanato-1-butene. The chemical components of the essential oil of the crude Semen Sinapis were more than that of the roasted Semen Sinapis. The effect of different processing methods on the chemical components of the essential oil of Semen Sinapis was significant. Certain chemical components such as isothiocyanato-containing substances, were found in the crude Semen Sinapis.

Exposure to volatile organic compounds in an ethanol and gasoline service station.

PubMed

de Oliveira, K M P G; Martins, E M; Arbilla, G; Gatti, L V

2007-08-01

The present study was conducted to determine the VOCs concentrations in a service station located in a residential and commercial area in the city of Rio de Janeiro. This is, to our knowledge, the first published determination in Brazil, where both ethanol and ethanol-blended gasoline are used. Electro polished, stainless steel, evacuated canisters were used for sampling. The analysis was performed by gaschromatography with flame ionization detection (CG-FID) and by gas chromatography-mass spectrometry (CG-MS). A total of 80 and 56 compounds were determined in samples collected at the service station and control location, respectively. The most abundant compounds at the service station were in order of decreasing concentration (units: microg m(-3)): 2-methylbutane (1,715.7), 2-methylbut-1-ene (1,043.2), isobutene (758.8), 2-methylprop-1-ene (703.7), 2-methylpentane (492.1), pentadi-1,3-ene (189.7), toluene (157.0), benzene (144.5), but-2-ene (126.3) and m,p-xylene (123.2). A mean concentration of 144.5 microg m(-3) was determined for benzene, this value is about ten times the concentration determined in the control location in this work and about 70 times the value determined in other locations of Rio de Janeiro using charcoal cartridges for the sampling. The mean benzene/toluene ratios are 0.92 and 0.31 in the service station and control location, respectively. Since in Brazil service station workers are employed to fill customer's cars (self-service is not commonly used) the possible risk of cancer of these workers should be evaluated in a future study.

Synthesis of novel acid electrolytes for phosphoric acid fuel cells

NASA Astrophysics Data System (ADS)

Adcock, James L.

1988-11-01

A 40 millimole per hour scale aerosol direct fluorination reactor was constructed. F-Methyl F-4-methoxybutanoate and F-4-methoxybutanoyl fluoride were synthesized by aerosol direct fluorination of methyl 4-methoxybutanoate. Basic hydrolysis of the perfluorinated derivatives produce sodium F-4 methoxybutanoate which was pyrolyzed to F-3-methoxy-1-propene. Purification and shipment of 33 grams of F-3-methoxy-1-propene followed. Syntheses by analogous methods allowed production and shipment of 5 grams of F-3-ethoxy 1-propene, 18 grams of F-3-(2-methoxy.ethoxy) 1-propene, and 37 grams of F-3,3-dimethyl 1-butene. Eighteen grams of F-2,2-dimethyl 1-chloropropane was produced directly and shipped. As suggested by other contractors, 5 grams of F-3-methoxy 1-iodopropane, and 5 grams of F-3-(2-methoxy.ethoxy) 1-iodopropane were produced by converting the respective precursor acid sodium salts produced for olefin synthesis to the silver salts and pyrolyzing them with iodine. Each of these compounds was prepared for the first time by the aerosol fluorination process during the course of the contract. These samples were provided to other Gas Research Institute (GRI) contractors for synthesis of perfluorinated sulfur (VI) and phosphorous (V) acids.

Biotransformation of menadione to its prenylated derivative MK-3 using recombinant Pichia pastoris.

PubMed

Li, Zhemin; Zhao, Genhai; Liu, Hui; Guo, Yugang; Wu, Hefang; Sun, Xiaowen; Wu, Xihua; Zheng, Zhiming

2017-07-01

Prenylated quinones, especially menaquinones, have significant physiological activities, but are arduous to synthesize efficiently. Due to the relaxed aromatic substrate specificity and prenylation regiospecificity at the ortho- site of the phenolic hydroxyl group, the aromatic prenyltransferase NovQ from Streptomyces may be useful in menaquinone synthesis from menadione. In this study, NovQ was overexpressed in Pichia pastoris. After fermentation optimization, NovQ production increased by 1617%. Then the different effects of metal ions, detergents and pH on the activity of purified NovQ were investigated to optimize the prenylation reaction. Finally, purified NovQ and cells containing NovQ were used for menadione prenylation in vitro and in vivo, respectively. Menaquinone-1 (MK-1) was detected as the only product in vitro with γ,γ-dimethylallyl pyrophosphate and menadione hydroquinol substrates. MK-3 at a concentration of 90.53 mg/L was detected as the major product of whole cell catalysis with 3-methyl-2-buten-1-ol and menadione hydroquinol substrates. This study realized whole cell catalysis converting menadione to menaquinones.

Accessing Valuable Ligand Supports for Transition Metals: A Modified, Intermediate Scale Preparation of 1,2,3,4,5-Pentamethylcyclopentadiene.

PubMed

Call, Zachary; Suchewski, Meagan; Bradley, Christopher A

2017-03-20

A reliable, intermediate scale preparation of 1,2,3,4,5-pentamethylcyclopentadiene (Cp*H) is presented, based on modifications of existing protocols that derive from initial 2-bromo-2-butene lithiation followed by acid mediated dienol cyclization. The revised synthesis and purification of the ligand avoids the use of mechanical stirring while still permitting access to significant quantities (39 g) of Cp*H in good yield (58%). The procedure offers other additional benefits, including a more controlled quench of excess lithium during the production of the intermediate heptadienols and a simplified isolation of Cp*H of sufficient purity for metallation with transition metals. The ligand was subsequently used to synthesize [Cp*MCl2]2 complexes of both iridium and ruthenium to demonstrate the utility of the Cp*H prepared and purified by our method. The procedure outlined herein affords substantial quantities of a ubiquitous ancillary ligand support used in organometallic chemistry while minimizing the need for specialized laboratory equipment, thus providing a simpler and more accessible entry point into the chemistry of 1,2,3,4,5-pentamethylcyclopentadiene.

Zeolite catalysis in the synthesis of isobutylene from hydrous ethanol

NASA Astrophysics Data System (ADS)

Phillips, Cory Bernard

1999-11-01

This work deals with the synthesis of isobutylene from a hydrous ethanol feedstock over zeolites. The synthesis is accomplished in three steps: (1) low-temperature direct ethanol conversion to ethylene on H-ZSM-5 zeolite, (2) ethylene conversion to butene products over metal-exchanged zeolites, and (3) butene skeletal rearrangement to isobutylene over FER zeolites. The key to understanding and optimizing each synthesis step lies in the ability to control and regulate the zeolite acidity (Bronsted and Lewis)---both strength and number. Therefore, the continuous temperature programmed amine desorption (CTPAD) technique was further developed to simultaneously count the Bronsted acid sites and quantitatively characterize their strength. The adsorption of ethanol, reaction products, amines, coke and ethanol-derived residue (EDR) were monitored gravimetrically using the highly sensitive, novel Tapered Element Oscillating Microreactor (TEOM) apparatus. The TEOM was also used also in conjunction with CTPAD to characterize Bronsted acidity which is a new application for the instrument. For the first synthesis step, a parallel reaction exists which simultaneously produces diethyl ether and ethylene directly over H-ZSM-5. The reaction rates for each pathway were measured directly using a differential reactor operating at low temperatures (<473 K). Water in the ethanol feed enhances the rate of ethylene formation. A mechanism and kinetic expression are proposed for this reaction over H-ZSM-5, with diethyl-ether desorption and ethylene formation as the rate limiting steps. Heat of adsorption values measured from the independent microcalorimetry work reported in the literature are incorporated into the kinetic analysis which reduces the number of regressed parameters. For the remaining synthesis steps, several zeolite structures (ZSM-5, Y, FER) partially exchanged with Pd, Ti, Ni and Au were prepared and tested. It was determined from this screening study that the zeolites containing Pd are the most efficient catalysts for the dimerization reaction. Characterization results from x-ray diffraction (XRD), electron paramagnetic resonance (EPR) spectroscopy, and CTPAD suggest a stable, Pd species with a low oxidation state as part of the active site in Pd-exchanged zeolites. Isobutylene was present in the C4 fraction at reasonable quantities for most of the catalyst candidates, especially those containing an alkali metal co-cation.

Fire extinguishing tests -80 with methyl alcohol gasoline (in MIXED)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holmstedt, G.; Ryderman, A.; Carlsson, B.

1980-01-01

Large scale tests and laboratory experiments were carried out for estimating the extinguishing effectiveness of three alcohol resistant aqueous film forming foams (AFFF), two alcohol resistant fluoroprotein foams and two detergent foams in various poolfires: gasoline, isopropyl alcohol, acetone, methyl-ethyl ketone, methyl alcohol and M15 (a gasoline, methyl alcohol, isobutene mixture). The scaling down of large scale tests for developing a reliable laboratory method was especially examined. The tests were performed with semidirect foam application, in pools of 50, 11, 4, 0.6, and 0.25 sq m. Burning time, temperature distribution in the liquid, and thermal radiation were determined. An M15more » fire can be extinguished with a detergent foam, but it is impossible to extinguish fires in polar solvents, such as methyl alcohol, acetone, and isopropyl alcohol with detergent foams, AFFF give the best results, and performances with small pools can hardly be correlated with results from large scale fires.« less

Development of three stable isotope dilution assays for the quantitation of (E)-2-butenal (crotonaldehyde) in heat-processed edible fats and oils as well as in food.

PubMed

Granvogl, Michael

2014-02-12

Three stable isotope dilution assays (SIDAs) were developed for the quantitation of (E)-2-butenal (crotonaldehyde) in heat-processed edible fats and oils as well as in food using synthesized [¹³C₄]-crotonaldehyde as internal standard. First, a direct headspace GC-MS method, followed by two indirect methods on the basis of derivatization with either pentafluorophenylhydrazine (GC-MS) or 2,4-dinitrophenylhydrazine (LC-MS/MS), was developed. All methods are also suitable for the quantitation of acrolein using the standard [¹³C₃]-acrolein. Applying these three methods on five different types of fats and oils varying in their fatty acid compositions revealed significantly varying crotonaldehyde concentrations for the different samples, but nearly identical quantitative data for all methods. Formed amounts of crotonaldehyde were dependent not only on the type of oil, e.g., 0.29-0.32 mg/kg of coconut oil or 33.9-34.4 mg/kg of linseed oil after heat-processing for 24 h at 180 °C, but also on the applied temperature and time. The results indicated that the concentration of formed crotonaldehyde seemed to be correlated with the amount of linolenic acid in the oils. Furthermore, the formation of crotonaldehyde was compared to that of its homologue acrolein, demonstrating that acrolein was always present in higher amounts in heat-processed oils, e.g., 12.3 mg of crotonaldehyde/kg of rapeseed oil in comparison to 23.4 mg of acrolein/kg after 24 h at 180 °C. Finally, crotonaldehyde was also quantitated in fried food, revealing concentrations from 12 to 25 μg/kg for potato chips and from 8 to 19 μg/kg for donuts, depending on the oil used.

Investigation of potential interferences in the detection of atmospheric ROx radicals by laser-induced fluorescence under dark conditions

NASA Astrophysics Data System (ADS)

Fuchs, H.; Tan, Z.; Hofzumahaus, A.; Broch, S.; Dorn, H.-P.; Holland, F.; Künstler, C.; Gomm, S.; Rohrer, F.; Schrade, S.; Tillmann, R.; Wahner, A.

2015-11-01

Direct detection of highly reactive, atmospheric hydroxyl radicals (OH) is widely accomplished by laser-induced fluorescence (LIF) instruments. The technique is also suitable for the indirect measurement of HO2 and RO2 peroxy radicals by chemical conversion to OH. It requires sampling of ambient air into a low pressure cell, where OH fluorescence is detected after excitation by 308 nm laser radiation. Although the residence time of air inside the fluorescence cell is typically only on the order of milliseconds, there is potential that additional OH is internally produced, which would artificially increase the measured OH concentration. Here, we present experimental studies investigating potential interferences in the detection of OH and peroxy radicals for the LIF instruments of Forschungszentrum Jülich for nighttime conditions. For laboratory experiments, the inlet of the instrument was overflown by excess synthetic air containing one or more reactants. In order to distinguish between OH produced by reactions upstream of the inlet and artificial signals produced inside the instrument, a chemical titration for OH was applied. Additional experiments were performed in the simulation chamber SAPHIR where simultaneous measurements by an open-path differential optical absorption spectrometer (DOAS) served as reference for OH to quantify potential artifacts in the LIF instrument. Experiments included the investigation of potential interferences related to the nitrate radical (NO3, N2O5), related to the ozonolysis of alkenes (ethene, propene, 1-butene, 2,3-dimethyl-2-butene, α-pinene, limonene, isoprene), and the laser photolysis of acetone. Experiments studying the laser photolysis of acetone yield OH signals in the fluorescence cell, which are equivalent to 0.05 × 106 cm-3 OH for a mixing ratio of 5 ppbv acetone. Under most atmospheric conditions, this interference is negligible. No significant interferences were found for atmospheric concentrations of reactants during ozonolysis experiments. Only for α-pinene, limonene, and isoprene at reactant concentrations which are orders of magnitude higher than in the atmosphere artificial OH could be detected. The value of the interference depends on the turnover rate of the ozonolysis reaction. For example, an apparent OH concentration of approximately 1 × 106 cm-3 is observed, if 5.8 ppbv limonene reacts with 600 ppbv ozone. Experiments with the nitrate radical NO3 reveal a small interference signal in the OH, HO2 and RO2 detection. Dependencies on experimental parameters point to artificial OH formation by surface reactions at the chamber walls or in molecular clusters in the gas expansion. The signal scales with the presence of NO3 giving equivalent radical concentrations of 1.1 × 105 cm-3 OH, 1 × 107 cm-3 HO2, and 1.7 × 107 cm-3 RO2 per 10 pptv NO3.

A gas ionisation detector in the axial (Bragg) geometry used for the time-of-flight elastic recoil detection analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Siketić, Zdravko; Skukan, Natko; Bogdanović Radović, Iva

2015-08-15

In this paper, time-of-flight elastic recoil detection analysis spectrometer with a newly constructed gas ionization detector for energy detection is presented. The detector is designed in the axial (Bragg) geometry with a 3 × 3 array of 50 nm thick Si{sub 3}N{sub 4} membranes as an entrance window. 40 mbar isobutane gas was sufficient to stop a 30 MeV primary iodine beam as well as all recoils in the detector volume. Spectrometer and detector performances were determined showing significant improvement in the mass and energy resolution, respectively, comparing to the spectrometer with a standard silicon particle detector for an energymore » measurement.« less

The Lawrence Berkeley Laboratory geothermal program in northern Nevada

NASA Technical Reports Server (NTRS)

Mirk, K. F.; Wollenberg, H. A.

1974-01-01

The Lawrence Berkeley Laboratory's geothermal program began with consideration of regions where fluids in the temperature range of 150 to 230 C may be economically accessible. Three valleys, located in an area of high regional heat flow in north central Nevada, were selected for geological, geophysical, and geochemical field studies. The objective of these ongoing field activities is to select a site for a 10-MW demonstration plant. Field activities (which started in September 1973) are described. A parallel effort has been directed toward the conceptual design of a 10-MW isobutane binary plant which is planned for construction at the selected site. Design details of the plant are described. Project schedule with milestones is shown together with a cost summary of the project.

Degraded protein adducts of cis-2-butene-1,4-dial are urinary and hepatocyte metabolites of furan.

PubMed

Lu, Ding; Sullivan, Mathilde M; Phillips, Martin B; Peterson, Lisa A

2009-06-01

Furan is a liver toxicant and carcinogen in rodents. On the basis of these observations and the large potential for human exposure, furan has been classified as a possible human carcinogen. The mechanism of tumor induction by furan is unknown. However, the toxicity requires cytochrome P450-catalyzed oxidation of furan. The product of this oxidation, cis-2-butene-1,4-dial (BDA), reacts readily with glutathione, amino acids, and DNA and is a bacterial mutagen in Ames assay strain TA104. Characterization of the urinary metabolites of furan is expected to provide information regarding the structure(s) of the reactive metabolite(s). Recently, several urinary metabolites have been identified. We reported the presence of a monoglutathione-BDA reaction product, N-[4-carboxy-4-(3-mercapto-1H-pyrrol-1-yl)-1-oxobutyl]-l-cysteinylglycine cyclic sulfide. Three additional urinary metabolites of furan were also characterized as follows: R-2-acetylamino-6-(2,5-dihydro-2-oxo-1H-pyrrol-1-yl)-1-hexanoic acid, N-acetyl-S-[1-(5-acetylamino-5-carboxypentyl)-1H-pyrrol-3-yl]-l-cysteine, and its sulfoxide. It was postulated that these three metabolites are derived from degraded protein adducts. However, the possibility that these metabolites result from the reaction of BDA with free lysine and/or cysteine was not ruled out. In this latter case, one might predict that the reaction of thiol-BDA with free lysine would not occur exclusively on the epsilon-amino group. Reaction of BDA with N-acetylcysteine or GSH in the presence of lysine indicated that both the alpha- and the epsilon-amino groups of lysine can be modified by thiol-BDA. The N-acetylcysteine-BDA-N-acetyllysine urinary metabolites were solely linked through the epsilon-amino group of lysine. A GSH-BDA-lysine cross-link was a significant hepatocyte metabolite of furan. In this case, the major product resulted from reaction with the epsilon-amino group of lysine; however, small amounts of the alpha-amino reaction product were also observed. Western analysis of liver and hepatocyte protein extracts using anti-GSH antibody indicated that GSH was covalently linked to proteins in tissues or cells exposed to furan. Our data support the hypothesis that GSH-BDA can react with either free lysine or protein lysine groups. These data suggest that there are multiple pathways by which furan can modify cellular nucleophiles. In one pathway, BDA reacts directly with proteins to form cysteine-lysine reaction products. In another, BDA reacts with GSH to form GSH-BDA conjugates, which then react with cellular nucleophiles like free lysine or lysine moieties in proteins. Both pathways will give rise to N-acetyl-S-[1-(5-acetylamino-5-carboxypentyl)-1H-pyrrol-3-yl]-l-cysteine. Given the abundance of these metabolites in urine of furan-treated rats, these pathways appear to be major pathways of furan biotransformation in vivo.

Degraded protein adducts of cis-2-butene-1,4-dial are urinary and hepatocyte metabolites of furan

PubMed Central

Lu, Ding; Sullivan, Mathilde M.; Phillips, Martin B.; Peterson, Lisa A.

2009-01-01

Furan is a liver toxicant and carcinogen in rodents. Based on these observations and the large potential for human exposure, furan has been classified as a possible human carcinogen. The mechanism of tumor induction by furan is unknown. However, the toxicity requires cytochrome P450 catalyzed oxidation of furan. The product of this oxidation, cis-2-butene-1,4-dial (BDA), reacts readily with glutathione, amino acids and DNA and is a bacterial mutagen in Ames assay strain TA104. Characterization of the urinary metabolites of furan is expected to provide information regarding the structure(s) of the reactive metabolite(s). Recently, several urinary metabolites have been identified. We reported the presence of a mono-glutathione-BDA reaction product, N-[4-carboxy-4-(3-mercapto-1H-pyrrol-1-yl)-1-oxobutyl]-L-cysteinylglycine cyclic sulfide. Three additional urinary metabolites of furan were also characterized: R-2-acetylamino-6-(2,5-dihydro-2-oxo-1H-pyrrol-1-yl)-1-hexanoic acid, N-acetyl-S-[1-(5-acetylamino-5-carboxypentyl)-1H-pyrrol-3-yl]-L-cysteine and its sulfoxide. It was postulated that these three metabolites are derived from degraded protein adducts. However, the possibility that these metabolites result from reaction of BDA with free lysine and/or cysteine was not ruled out. In this latter case, one might predict that the reaction of thiol-BDA with free lysine would not occur exclusively on the ε-amino group. Reaction of BDA with N-acetylcysteine or GSH in the presence of lysine indicated that both the α- and ε-amino groups of lysine can be modified by thiol-BDA. The N-acetylcysteine-BDA-N-acetyllysine urinary metabolites were solely linked through the ε-amino group of lysine. A GSH-BDA-lysine crosslink was a significant hepatocyte metabolite of furan. In this case, the major product resulted from reaction with the ε-amino group of lysine, however, small amounts of the α-amino reaction product were also observed. Western analysis of liver and hepatocyte protein extracts using anti-GSH antibody indicated that GSH was covalently linked to proteins in tissues or cells exposed to furan. Our data support the hypothesis that GSH-BDA can react with either free lysine or protein lysine groups. These data suggest that there are multiple pathways by which furan can modify cellular nucleophiles. In one pathway, BDA reacts directly with proteins to form cysteine-lysine reaction products. In another, BDA reacts with GSH to form GSH-BDA conjugates which then reacts with cellular nucleophiles like free lysine or lysine moieties in proteins. Both pathways will give rise to N-acetyl-S-[1-(5-acetylamino-5-carboxypentyl)-1H-pyrrol-3-yl]-L-cysteine. Given the abundance of these metabolites in urine of furan-treated rats, these pathways appear to be major pathways of furan biotransformation in vivo. PMID:19441776

Gas-Phase Dimerization of Ethylene under Mild Conditions Catalyzed by MOF Materials Containing (bpy)Ni II Complexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madrahimov, Sherzod T.; Gallagher, James R.; Zhang, Guanghui

2015-10-09

NU-1000-(bpy)Ni-II, a highly porous MOF material possessing well-defined (bpy)Ni-II moieties, was prepared through solvent-assisted ligand incorporation (SALI). Treatment with Et2AlCl affords a single-site catalyst with excellent catalytic activity for ethylene dimerization (intrinsic activity for butenes that is up to an order of magnitude higher than the corresponding (bpy)NiCl2 homogeneous analogue) and stability (can be reused at least three times). The high porosity of this catalyst results in outstanding levels of activity at ambient temperature in gas-phase ethylene dimerization reactions, both under batch and continuous flow conditions.

Active sites and states in the heterogeneous catalysis of carbon-hydrogen bonds.

PubMed

Somorjai, Gabor A; Marsh, Anderson L

2005-04-15

C-H bond activation for several alkenes (ethylene, propylene, isobutene, cyclohexene and 1-hexene) and alkanes (methane, ethane, n-hexane, 2-methylpentane and 3-methylpentane) has been studied on the (111) crystal face of platinum as a function of temperature at low (10(-6) Torr) and high (>/=1 Torr) pressures in the absence and presence of hydrogen pressures (>/=10 Torr). Sum frequency generation (SFG) vibrational spectroscopy has been used to characterize the adsorbate structures and high pressure scanning tunnelling microscopy (HP-STM) has been used to monitor their surface mobility under reaction conditions during hydrogenation, dehydrogenation and CO poisoning. C-H bond dissociation occurs at low temperatures, approximately 250 K, for all of these molecules, although only at high pressures for the weakly bound alkanes because of their low desorption temperatures. Bond dissociation is known to be surface structure sensitive and we find that it is also accompanied by the restructuring of the metal surface. The presence of hydrogen slows down dehydrogenation and for some of the molecules it influences the molecular rearrangement, thus altering reaction selectivity. Surface mobility of adsorbates is essential to produce catalytic activity. When surface diffusion is inhibited by CO adsorption, ordered surface structures form and the reaction is poisoned. Ethylene hydrogenation is surface structure insensitive, while cyclohexene hydrogenation and dehydrogenation are structure sensitive. n-Hexane and other C6 alkanes form either upright or flat-lying molecules on the platinum surface which react to produce branched isomers or benzene, respectively.

Quantifying Interfacial pH Variation at Molecular Length Scales Using a Concurrent Non-Faradaic Reaction.

PubMed

Ryu, Jaeyune; Wuttig, Anna; Surendranath, Yogesh

2018-05-15

We quantify changes in the interfacial pH local to the electrochemical double layer during electrocatalysis, using a concurrent non-faradaic probe reaction. In the absence of electrocatalysis, nanostructured Pt/C surfaces mediate the reaction of H2 with cis-2-butene-1,4-diol to form a mixture of 1,4-butanediol and n-butanol with a selectivity that is linearly dependent on the bulk solution pH. We show that kinetic branching occurs from a common surface-bound intermediate, ensuring that this probe reaction is uniquely sensitive to the interfacial pH within molecular length scales of the surface. We use the pH-dependent selectivity of this reaction to track changes in interfacial pH during concurrent hydrogen oxidation electrocatalysis and find that the local pH can vary dramatically, > 3 units, relative to the bulk value even at modest current densities in well-buffered electrolytes. This work highlights the key role that interfacial pH variation plays in modulating inner-sphere electrocatalysis. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Alternative to conventional extraction of vetiver oil: Microwave hydrodistillation of essential oil from vetiver roots (Vetiveria zizanioides)

NASA Astrophysics Data System (ADS)

Kusuma, H. S.; Altway, A.; Mahfud, M.

2017-12-01

In this study the extraction of essential oil from vetiver roots (Vetiveria zizanioides) has been carried out by using microwave hydrodistillation. In the extraction of vetiver oil using microwave hydrodistillation method is studied the effect of microwave power, feed to solvent (F/S) ratio and extraction time on the yield of vetiver oil. Besides, in this study can be seen that microwave hydrodistillation method offers important advantages over hydrodistillation, such as shorter extraction time (3 h vs. 24 h for hydrodistillation); better yields (0.49% vs. 0.46% for hydrodistillation); and environmental impact (energy cost is appreciably higher for performing hydrodistillation than that required for extraction using microwave hydrodistillation). Based on the analysis using GC-MS can be seen 19 components on vetiver oil that has been extracted using microwave hydrodistillation. In addition, GC-MS analysis showed that the main components of vetiver oil that has been extracted using microwave hydrodistillation method were β-Gurjunene (30.12%), α-Vetivone (20.12%), 4-(1-cyclohexenyl)-2-trimethylsilymethyl-1-buten-3-yne (13.52%) and δ-Selinene (7.27%).

Synthesis and characterization of water-soluble hydroxybutenyl cyclomaltooligosaccharides (cyclodextrins).

PubMed

Buchanan, Charles M; Alderson, Susan R; Cleven, Curtis D; Dixon, Daniel W; Ivanyi, Robert; Lambert, Juanelle L; Lowman, Douglas W; Offerman, Rick J; Szejtli, Jozsef; Szente, Lajos

2002-03-15

We have examined the synthesis of hydroxybutenyl cyclomaltooligosaccharides (cyclodextrins) and the ability of these cyclodextrin ethers to form guest-host complexes with guest molecules. The hydroxybutenyl cyclodextrin ethers were prepared by a base-catalyzed reaction of 3,4-epoxy-1-butene with the parent cyclodextrins in an aqueous medium. Reaction byproducts were removed by nanofiltration before the hydroxybutenyl cyclodextrins were isolated by co-evaporation of water-EtOH. Hydroxybutenyl cyclodextrins containing no unsubstituted parent cyclodextrin typically have a degree of substitution of 2-4 and a molar substitution of 4-7. These hydroxybutenyl cyclodextrins are randomly substituted, amorphous solids. The hydroxybutenyl cyclodextrin ethers were found to be highly water soluble. Complexes of HBen-beta-CD with glibenclamide and ibuprofen were prepared and isolated. In both cases, the guest content of the complexes was large, and a significant increase in the solubility of the free drug was observed. Dissolution of the complexes in pH 1.4 water was very rapid, and significant increases in the solubility of the free drugs were observed. Significantly, after reaching equilibrium concentration, a decrease in the drug concentration over time was not observed.

[Emission Characteristics of VOCs from Typical Restaurants in Beijing].

PubMed

Cui, Tong; Cheng, Jing-chen; He, Wan-qing; Ren, Pei-fang; Nie, Lei; Xu, Dong-yao; Pan, Tao

2015-05-01

Using the EPA method, emission of volatile organic compounds (VOCs) , sampled from barbecue, Chinese and Western fast-food, Sichuan cuisine and Zhejiang cuisine restaurants in Beijing was investigated. VOCs concentrations and components from different cuisines were studied. The results indicated that based on the calibrated baseline ventilation volume, the VOCs emission level from barbecue was the highest, reaching 12.22 mg · m(-3), while those from fast-food of either Chinese or Western, Sichuan cuisine and Zhejiang cuisine were about 4 mg · m(-3). The components of VOCs from barbecue were different from those in the other cuisines, which were mainly propylene, 1-butene, n-butane, etc. The non-barbecue cuisines consisted of high concentration of alcohols, and Western fast-food contained relatively high proportion of aldehydes and ketones organic compounds. According to emission concentration of baseline ventilation volume, barbecue released more pollutants than the non-barbecue cuisines at the same scale. So, barbecue should be supervised and controlled with the top priority.

Volatiles from roasted byproducts of the poultry-processing industry.

PubMed

Wettasinghe, M; Vasanthan, T; Temelli, F; Swallow, K

2000-08-01

Volatiles of roasted chicken breast muscle and byproducts, such as backbones, breastbones, spent bones, and skin, were investigated. Total volatile concentrations ranged from 2030 ppb in the roasted backbones to 4049 ppb in the roasted skin. The major classes of volatile compounds detected in roasted samples were aldehydes (648-1532 ppb) and alcohols (336-1006 ppb). Nitrogen- and/or sulfur-containing compounds were also detected in appreciable quantities (161-706 ppb) in all samples. For all samples, hexanal and 2-methyl-2-buten-1-ol were dominant among the aldehydes and alcohols, respectively. Among the nitrogen- and sulfur-containing compounds, Maillard reaction products, such as tetrahydropyridazines, piperidines, and thiazoles, were the major contributors to the total volatile content in all samples. The composition of volatiles observed in roasted byproducts was markedly different from that of the roasted breast muscle. Therefore, the blending of the byproducts in appropriate proportions or blending of volatile flavor extracts from different byproducts may be necessary to obtain an aroma that mimics roasted chicken aroma.

Amonia gas: an improved reagent for chemical ionization mass spectrometry of bile acid methyl ester acetates

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeMark, B.R.; Klein, P.D.

1981-01-01

The ammonia chemical ionization mass spectra of 28 methyl ester acetate derivatives of bile acids and related compounds have been determined by gas-liquid chromatography-mass spectrometry. Advantages of ammonia ionization over the previously studied isobutane ionization include a 130 to 270% enhancement in the sensitivity of base peak monitoring, and direct determination of molecular weight from the base peak (M + NH/sub 4//sup +/) in the mass spectrum of any of the derivatives. Minor ions in the ammonia spectra also allow selective detection of 3-keto compounds and can indicate unsaturation or double bond conjugation in the molecule. The significance of thesemore » studies for the detection and quantitation of bile acids is discussed. 2 tables.« less

Biological monitoring of isocyanates and related amines. I. Determination of 1,6-hexamethylene diamine (HDA) in hydrolysed human urine after oral administration of HDA.

PubMed

Brorson, T; Skarping, G; Sandström, J F; Stenberg, M

1990-01-01

1,6-Hexamethylene diamine (HDA), used as raw material in industrial manufacturing operations, was orally administered to six healthy volunteers. After acid hydrolysis of the urine by hydrochloric acid, HDA and the metabolite 6-aminohexanoic acid were quantified. HDA was determined as an ethyl-chloroformate derivative by capillary gas chromatography using thermionic specific detection (TSD), and 6-aminohexanoic acid was quantified by ion chromatography using the ninhydrin reaction. In nonhydrolysed urine, monoacetylated HDA (N-acetyl-1,6-hexamethylene diamine) and HDA, were verified as heptafluorobutyric anhydride derivatives by gas chromatography-mass spectrometry (GC-MS), in a chemical ionization mode using isobutane and ammonia as reagent gases. In hydrolysed urine, a mean of 0.28 mg (range 1-6%) of the administered dose (8.2 mg) was recovered as HDA, and a mean of 0.8 mg (range less than 1-27%) as 6-aminohexanoic acid. The urinary excretion of both the determined compounds was rapid, and the principal part (greater than 90%) of the elimination was completed within 10 h. There was a considerable inter-individual variation in the excreted amounts, but the intra-individual variation in the excretion of HDA was limited. The subjects N-acetylator phenotype was determined by a dapsone test. Three slow acetylators excreted lower amounts (mean 2% of given dose) of HDA than three rapid ones (mean 5%).

Synthesis of (1R,2S)-1-amino-2-vinylcyclopropanecarboxylic acid vinyl-ACCA) derivatives: key intermediates for the preparation of inhibitors of the hepatitis C virus NS3 protease.

PubMed

Beaulieu, Pierre L; Gillard, James; Bailey, Murray D; Boucher, Colette; Duceppe, Jean-Simon; Simoneau, Bruno; Wang, Xiao-Jun; Zhang, Li; Grozinger, Karl; Houpis, Ioannis; Farina, Vittorio; Heimroth, Heidi; Krueger, Thomas; Schnaubelt, Jürgen

2005-07-22

(1R,2S)-1-Amino-2-vinylcyclopropanecarboxylic acid (vinyl-ACCA) is a key building block in the synthesis of potent inhibitors of the hepatitis C virus NS3 protease such as BILN 2061, which was recently shown to dramatically reduce viral load after administration to patients infected with HCV genotype 1. We have developed a scalable process that delivers derivatives of this unusual amino acid in >99% ee. The strategy was based on the dialkylation of a glycine Schiff base using trans-1,4-dibromo-2-butene as an electrophile to produce racemic vinyl-ACCA, which was subsequently resolved using a readily available, inexpensive esterase enzyme (Alcalase 2.4L). Factors that affect diastereoselection in the initial dialkylation steps were examined and the conditions optimized to deliver the desired diastereomer selectively. Product inhibition, which was encountered during the enzymatic resolution step, initially resulted in prolonged cycle times. Enrichment of racemic vinyl-ACCA through a chemical resolution via diastereomeric salt formation or the use of forcing conditions in the enzymatic reaction both led to improvements in throughput and the development of a viable process. The chemistry described herein was scaled up to produce multikilogram quantities of this building block.

Thermochemical Studies of Epoxides and Related Compounds

PubMed Central

Morgan, Kathleen M.; Ellis, Jamie A.; Lee, Joseph; Fulton, Ashley; Wilson, Shavonda L.; Dupart, Patrick S.; Dastoori, Rosanna

2013-01-01

Gas phase heats of formation for the our butene oxide isomers are reported. They were obtained by measuring the condensed-phase heat of reduction to the corresponding alcohol using reaction calorimetry. Heats of vaporization were determined, and allow gas-phase heats of formation to be obtained. The experimental measurements are compared to calculations obtained using a variety of computational methods. Overall, the G3 and CBS-APNO methods agree quite well with the experimental data. The influence of alkyl substituents on epoxide stability is discussed. Comparisons to alkenes, cyclopropanes, aziridines, thiiranes and phosphiranes are also made. Isodesmic-type reactions were used to determine strain energies of the epoxides and related compounds with various substituents. PMID:23551240

Method for etherifications

DOEpatents

Jones, E.M. Jr.

1985-03-12

A method is described for producing tertiary ethers from C[sub 4] or C[sub 5] streams containing isobutene and isoamylene respectively in a process wherein a acidic cation exchange resin is used as the catalyst and as a distillation structure in a distillation reactor column, wherein the improvement is the operation of the catalytic distillation in two zones at different pressures, the first zone containing the catalyst packing and operated a higher pressure in the range of 100 to 200 psig in the case of C[sub 4] and 15 to 100 psig in the case of C[sub 5] which favors the etherification reaction and the second zone being a distillation operated at a lower pressure in the range of 0 to 100 psig in the case of C[sub 4] and 0 to 15 psig in the case of C[sub 5] wherein a first overhead from the first zone is fractionated to remove a portion of the unreacted alcohol from the first overhead and to return a condensed portion containing said alcohol to the first zone and to produce a second overhead having less alcohol than said first overhead. 3 figs.

Method for etherifications

DOEpatents

Jones, Jr., Edward M.

1985-01-01

A method for producing tertiary ethers from C.sub.4 or C.sub.5 streams containing isobutene and isoamylene respectively in a process wherein a acidic cation exchange resin is used as the catalyst and as a distillation structure in a distillation reactor column, wherein the improvement is the operation of the catalytic distillation in two zones at different pressures, the first zone containing the catalyst packing and operated a higher pressure in the range of 100 to 200 psig in the case of C.sub.4 's and 15 to 100 psig in the case of C.sub.5 's which favors the etherification reaction and the second zone being a distillation operated at a lower pressure in the range of 0 to 100 psig in the case of C.sub.4 's and 0 to 15 psig in the case of C.sub.5 's wherein a first overhead from the first zone is fractionated to remove a portion of the unreacted alcohol from the first overhead and to return a condensed portion containing said alcohol to the first zone and to produce a second overhead having less alcohol than said first overhead.

Palladium-Catalyzed Anti-Markovnikov Oxidation of Allylic Amides to Protected β-Amino Aldehydes.

PubMed

Dong, Jia Jia; Harvey, Emma C; Fañanás-Mastral, Martín; Browne, Wesley R; Feringa, Ben L

2014-12-10

A general method for the preparation of N-protected β-amino aldehydes from allylic amines or linear allylic alcohols is described. Here the Pd(II)-catalyzed oxidation of N-protected allylic amines with benzoquinone is achieved in tBuOH under ambient conditions with excellent selectivity toward the anti-Markovnikov aldehyde products and full retention of configuration at the allylic carbon. The method shows a wide substrate scope and is tolerant of a range of protecting groups. Furthermore, β-amino aldehydes can be obtained directly from protected allylic alcohols via palladium-catalyzed autotandem reactions, and the application of this method to the synthesis of β-peptide aldehydes is described. From a mechanistic perspective, we demonstrate that tBuOH acts as a nucleophile in the reaction and that the initially formed tert-butyl ether undergoes spontaneous loss of isobutene to yield the aldehyde product. Furthermore, tBuOH can be used stoichiometrically, thereby broadening the solvent scope of the reaction. Primary and secondary alcohols do not undergo elimination, allowing the isolation of acetals, which subsequently can be hydrolyzed to their corresponding aldehyde products.

Lack of micronucleus induction activity of ethyl tertiary-butyl ether in the bone marrow of F344 rats by sub-chronic drinking-water treatment, inhalation exposure, or acute intraperitoneal injection.

PubMed

Noguchi, Tadashi; Kamigaito, Tomoyuki; Katagiri, Taku; Kondou, Hitomi; Yamazaki, Kazunori; Aiso, Shigetoshi; Nishizawa, Tomoshi; Nagano, Kasuke; Fukushima, Shoji

2013-01-01

Ethyl tertiary-butyl ether (ETBE) is an oxygenated gasoline additive synthesized from ethanol and isobutene that is used to reduce CO2 emissions. To support the Kyoto Protocol, the production of ETBE has undergone a marked increase. Previous reports have indicated that exposure to ETBE or methyl tertiary-butyl ether resulted in liver and kidney tumors in rats and/or mice. These reports raise concern about the effects of human exposure being brought about by the increased use of ETBE. The present study was conducted to evaluate the genotoxicity of ETBE using micronucleus induction of polychromatic erythrocytes in the bone marrow of male and female rats treated with ETBE in the drinking-water at concentrations of 0, 1,600, 4,000 or 10,000 ppm or exposed to ETBE vapor at 0, 500, 1,500 or 5,000 ppm for 13 weeks. There were no significant increases in micronucleus induction in either the drinking water-administered or inhalation-administered groups at any concentration of ETBE; although, in both groups red blood cells and hemoglobin concentration were slightly reduced in the peripheral blood in rats administered the highest concentration of ETBE. In addition, two consecutive daily intraperitoneal injections of ETBE at doses of 0, 250, 500 or 1,000 mg/kg did not increase the frequency of micronucleated bone marrow cells in either sex; all rats receiving intraperitoneal injections of ETBE at a dose of 2,000 mg/kg died after treatment day 1. These data suggest that ETBE is not genotoxic in vivo.

Investigation of potential interferences in the detection of atmospheric ROx radicals by laser-induced fluorescence under dark conditions

NASA Astrophysics Data System (ADS)

Fuchs, Hendrik; Tan, Zhaofeng; Hofzumahaus, Andreas; Broch, Sebastian; Dorn, Hans-Peter; Holland, Frank; Künstler, Christopher; Gomm, Sebastian; Rohrer, Franz; Schrade, Stephanie; Tillmann, Ralf; Wahner, Andreas

2016-04-01

Direct detection of highly reactive, atmospheric hydroxyl radicals (OH) is widely accomplished by laser-induced fluorescence (LIF) instruments. The technique is also suitable for the indirect measurement of HO2 and RO2 peroxy radicals by chemical conversion to OH. It requires sampling of ambient air into a low-pressure cell, where OH fluorescence is detected after excitation by 308 nm laser radiation. Although the residence time of air inside the fluorescence cell is typically only on the order of milliseconds, there is potential that additional OH is internally produced, which would artificially increase the measured OH concentration. Here, we present experimental studies investigating potential interferences in the detection of OH and peroxy radicals for the LIF instruments of Forschungszentrum Jülich for nighttime conditions. For laboratory experiments, the inlet of the instrument was over flowed by excess synthetic air containing one or more reactants. In order to distinguish between OH produced by reactions upstream of the inlet and artificial signals produced inside the instrument, a chemical titration for OH was applied. Additional experiments were performed in the simulation chamber SAPHIR where simultaneous measurements by an open-path differential optical absorption spectrometer (DOAS) served as reference for OH to quantify potential artifacts in the LIF instrument. Experiments included the investigation of potential interferences related to the nitrate radical (NO3, N2O5), related to the ozonolysis of alkenes (ethene, propene, 1-butene, 2,3-dimethyl-2-butene, α-pinene, limonene, isoprene), and the laser photolysis of acetone. Experiments studying the laser photolysis of acetone yield OH signals in the fluorescence cell, which are equivalent to 0.05 × 106 cm-3 OH for a mixing ratio of 5 ppbv acetone. Under most atmospheric conditions, this interference is negligible. No significant interferences were found for atmospheric concentrations of reactants during ozonolysis experiments. Only for propene, α-pinene, limonene, and isoprene at reactant concentrations, which are orders of magnitude higher than in the atmosphere, could artificial OH be detected. The value of the interference depends on the turnover rate of the ozonolysis reaction. For example, an apparent OH concentration of approximately 1 × 106 cm-3 is observed when 5.8 ppbv limonene reacts with 600 ppbv ozone. Experiments with the nitrate radical NO3 reveal a small interference signal in the OH, HO2, and RO2 detection. Dependencies on experimental parameters point to artificial OH formation by surface reactions at the chamber walls or in molecular clusters in the gas expansion. The signal scales with the presence of NO3 giving equivalent radical concentrations of 1.1 × 105 cm-3 OH, 1 × 107 cm-3 HO2, and 1.7 × 107 cm-3 RO2 per 10 pptv NO3.

Gas mixture studies for streamer operated Resistive Plate Chambers

NASA Astrophysics Data System (ADS)

Paoloni, A.; Longhin, A.; Mengucci, A.; Pupilli, F.; Ventura, M.

2016-06-01

Resistive Plate Chambers operated in streamer mode are interesting detectors in neutrino and astro-particle physics applications (like OPERA and ARGO experiments). Such experiments are typically characterized by large area apparatuses with no stringent requirements on detector aging and rate capabilities. In this paper, results of cosmic ray tests performed on a RPC prototype using different gas mixtures are presented, the principal aim being the optimization of the TetraFluoroPropene concentration in Argon-based mixtures. The introduction of TetraFluoroPropene, besides its low Global Warming Power, is helpful because it simplifies safety requirements allowing to remove also isobutane from the mixture. Results obtained with mixtures containing SF6, CF4, CO2, N2 and He are also shown, presented both in terms of detectors properties (efficiency, multiple-streamer probability and time resolution) and in terms of streamer characteristics.

Structure determination and sensory analysis of bitter-tasting 4-vinylcatechol oligomers and their identification in roasted coffee by means of LC-MS/MS.

PubMed

Frank, Oliver; Blumberg, Simone; Kunert, Christof; Zehentbauer, Gerhard; Hofmann, Thomas

2007-03-07

Aimed at elucidating intense bitter-tasting molecules in coffee, various bean ingredients were thermally treated in model experiments and evaluated for their potential to produce bitter compounds. As caffeic acid was found to generate intense bitterness reminiscent of the bitter taste of a strongly roasted espresso-type coffee, the reaction products formed were screened for bitter compounds by means of taste dilution analysis, and the most bitter tastants were isolated and purified. LC-MS/MS as well as 1-D/2-D NMR experiments enabled the identification of 10 bitter compounds with rather low recognition threshold concentrations ranging between 23 and 178 micromol/L. These bitter compounds are the previously unreported 1,3-bis(3',4'-dihydroxyphenyl) butane, trans-1,3-bis(3',4'-dihydroxyphenyl)-1-butene, and eight multiply hydroxylated phenylindanes, among which five derivatives are reported for the first time. In addition, the occurrence of each of these bitter compounds in a coffee brew was verified by means of LC-MS/MS (ESI-) operating in the multiple reaction monitoring (MRM) mode. The structures of these bitter compounds show strong evidence that they are generated by oligomerization of 4-vinylcatechol released from caffeic acid moieties upon roasting.

Photo-oxidation of Polymers Synthesized by Plasma and Initiated CVD

DOE PAGES

Baxamusa, Salmaan H.; Suresh, Aravind; Ehrmann, Paul; ...

2015-11-09

Plasma polymers are often limited by their susceptibility to spontaneous and photo-oxidation. We show that the unusual photoluminescence (PL) behavior of a plasma polymer of trans-2-butene is correlated with its photoluminescence strength. These photo-processes occur under blue light illumination (λ=405 nm), distinguishing them from traditional ultraviolet degradation of polymers. These photo-active defects are likely formed during the plasma deposition process and we show that a polymer synthesized using initiated (i)CVD, non-plasma method, has 1000× lower PL signal and enhanced photo-stability. In conclusion, non-plasma methods such as iCVD may therefore be a route to overcoming material aging issues that limit themore » adoption of plasma polymers.« less

Mid-infrared multiheterodyne spectroscopy with phase-locked quantum cascade lasers

NASA Astrophysics Data System (ADS)

Westberg, J.; Sterczewski, L. A.; Wysocki, G.

2017-04-01

Fabry-Pérot (FP) quantum cascade lasers (QCLs) provide purely electronically controlled monolithic sources for broadband mid-infrared (mid-IR) multiheterodyne spectroscopy (MHS), which benefits from the large gain bandwidth of the QCLs without sacrificing the narrowband properties commonly associated with the single mode distributed feedback variant. We demonstrate a FP-QCL based multiheterodyne spectrometer with a short-term noise-equivalent absorption of ˜3 × 10-4/ √{ H z } , a mid-IR spectral coverage of 25 cm-1, and very short acquisition time (10 μs) capability. The broadband potential is demonstrated by measuring the absorption spectra of ammonia and isobutane under atmospheric pressure conditions. The stability of the system is enhanced by a two-stage active frequency inter-locking procedure, where the two QCLs are pre-locked with a slow feedback loop based on an analog frequency discriminator, followed by a high bandwidth optical phase-locked loop. The locking system provides a relative frequency stability in the sub kHz range over seconds of integration time. The strength of the technique lies in the ability to acquire spectral information from all optical modes simultaneously and individually, which bodes for a versatile and cost effective spectrometer for mid-IR chemical gas sensing.

High performance direct absorption spectroscopy of pure and binary mixture hydrocarbon gases in the 6-11 μm range

NASA Astrophysics Data System (ADS)

Heinrich, Robert; Popescu, Alexandru; Hangauer, Andreas; Strzoda, Rainer; Höfling, Sven

2017-08-01

The availability of accurate and fast hydrocarbon analyzers, capable of real-time operation while enabling feedback-loops, would lead to a paradigm change in the petro-chemical industry. Primarily gas chromatographs measure the composition of hydrocarbon process streams. Due to sophisticated gas sampling, these analyzers are limited in response time. As hydrocarbons absorb in the mid-infrared spectral range, the employment of fast spectroscopic systems is highly attractive due to significantly reduced maintenance costs and the capability to setup real-time process control. New developments in mid-infrared laser systems pave the way for the development of high-performance analyzers provided that accurate spectral models are available for multi-species detection. In order to overcome current deficiencies in the availability of spectroscopic data, we developed a laser-based setup covering the 6-11 μm wavelength range. The presented system is designated as laboratory reference system. Its spectral accuracy is at least 6.6× 10^{-3} cm^{-1} with a precision of 3× 10^{-3} cm^{-1}. With a "per point" minimum detectable absorption of 1.3× 10^{-3} cm^{-1} Hz^{{-}{1/2}} it allows us to perform systematic measurements of hydrocarbon spectra of the first 7 alkanes under conditions which are not tabulated in spectroscopic database. We exemplify the system performance with measured direct absorption spectra of methane, propane, iso-butane, and a mixture of methane and propane.

Chemoselective Hydrogenation with Supported Organoplatinum(IV) Catalyst on Zn(II)-Modified Silica

DOE Office of Scientific and Technical Information (OSTI.GOV)

Camacho-Bunquin, Jeffrey; Ferrandon, Magali; Sohn, Hyuntae

For this research, well-defined organoplatinum(IV) sites were grafted on a Zn(II)-modified SiO 2 support via surface organometallic chemistry in toluene at room temperature. Solid-state spectroscopies including XAS, DRIFTS, DRUV–vis, and solid-state (SS) NMR enhanced by dynamic nuclear polarization (DNP), as well as TPR-H 2 and TEM techniques revealed highly dispersed (methylcyclopentadienyl)methylplatinum(IV) sites on the surface ((MeCp)PtMe/Zn/SiO 2, 1). In addition, computational modeling suggests that the surface reaction of (MeCp)PtMe 3 with Zn(II)-modified SiO 2 support is thermodynamically favorable (ΔG = -12.4 kcal/mol), likely due to the increased acidity of the hydroxyl group, as indicated by NH 3-TPD and DNP-enhanced 17O{more » 1H} SSNMR. In situ DRIFTS and XAS hydrogenation experiments reveal the probable formation of a surface Pt(IV)-H upon hydrogenolysis of Pt-Me groups. The heterogenized organoplatinum(IV)-hydride sites catalyze the selective partial hydrogenation of 1,3-butadiene to butenes (up to 95%) and the reduction of nitrobenzene derivatives to anilines (up to 99%) with excellent tolerance of reduction-sensitive functional groups (olefin, carbonyl, nitrile, halogens) under mild reaction conditions.« less

Chemoselective Hydrogenation with Supported Organoplatinum(IV) Catalyst on Zn(II)-Modified Silica

DOE Office of Scientific and Technical Information (OSTI.GOV)

Camacho-Bunquin, Jeffrey; Ferrandon, Magali; Sohn, Hyuntae

Well-defined organoplatinum(IV) sites were grafted on a Zn(II)-modified SiO2 support via surface organometallic chemistry in toluene at room temperature. Solid-state spectroscopies including XAS, DRIFTS, DRUV-Vis, and solid-state (SS)NMR enhanced by dynamic nuclear polarization (DNP), as well as TPR-H2 and TEM techniques revealed highly dispersed (methylcyclopentadi-enyl)methylplatinum(IV) sites on the surface ((MeCp)PtMe/Zn/SiO2, 1). In addition, computational modelling suggests that the surface reaction of (MeCp)PtMe3 with Zn(II)-modified SiO2 support is thermodynamically favorable (ΔG = -12.4 kcal/mol), likely due to the increased acidity of the hydroxyl group, as confirmed by NH3-TPD and DNP-enhanced 17O{1H} SSNMR. In situ DRIFTS and XAS hydrogenation experiments reveal themore » formation of a surface Pt(IV)-H upon hydrogenolysis of Pt-Me groups. The heterogenized organoplatinum(IV)-H sites catalyze the selective partial hydrogenation of 1,3-butadiene to butenes (up to 95%) and the reduction of nitrobenzene derivatives to anilines (up to 100%) with excellent tolerance of reduction-sensitive func-tional groups (olefin, carbonyl, nitrile, halogens) under mild reaction conditions.« less

Chemoselective Hydrogenation with Supported Organoplatinum(IV) Catalyst on Zn(II)-Modified Silica

DOE PAGES

Camacho-Bunquin, Jeffrey; Ferrandon, Magali; Sohn, Hyuntae; ...

2018-02-27

For this research, well-defined organoplatinum(IV) sites were grafted on a Zn(II)-modified SiO 2 support via surface organometallic chemistry in toluene at room temperature. Solid-state spectroscopies including XAS, DRIFTS, DRUV–vis, and solid-state (SS) NMR enhanced by dynamic nuclear polarization (DNP), as well as TPR-H 2 and TEM techniques revealed highly dispersed (methylcyclopentadienyl)methylplatinum(IV) sites on the surface ((MeCp)PtMe/Zn/SiO 2, 1). In addition, computational modeling suggests that the surface reaction of (MeCp)PtMe 3 with Zn(II)-modified SiO 2 support is thermodynamically favorable (ΔG = -12.4 kcal/mol), likely due to the increased acidity of the hydroxyl group, as indicated by NH 3-TPD and DNP-enhanced 17O{more » 1H} SSNMR. In situ DRIFTS and XAS hydrogenation experiments reveal the probable formation of a surface Pt(IV)-H upon hydrogenolysis of Pt-Me groups. The heterogenized organoplatinum(IV)-hydride sites catalyze the selective partial hydrogenation of 1,3-butadiene to butenes (up to 95%) and the reduction of nitrobenzene derivatives to anilines (up to 99%) with excellent tolerance of reduction-sensitive functional groups (olefin, carbonyl, nitrile, halogens) under mild reaction conditions.« less

The rabbit liver microsomal biotransformation of 1,1-dialkylethylenes: enantioface selection of epoxidation and enantioselectivity of epoxide hydrolysis.

PubMed

Bellucci, G; Chiappe, C; Cordoni, A; Marioni, F

1994-01-01

The rabbit liver microsomal biotransformation of alpha-methylstyrene (1a), 2-methyl-1-hexene (1b), 2,4,4-trimethyl-1-pentene (1c), and 1,3,3-trimethyl-1-butene (1d) has been investigated with the aim at establishing the enantioface selection of the cytochrome P-450-promoted epoxidation of the double bond and the enantioselectivity of microsomal epoxide hydrolase(mEH)-catalyzed hydrolysis of the resulting epoxides. GLC on a Chiraldex G-TA (ASTEC) column was used to determine the enantiomeric composition of the products. The epoxides 2 first produced in incubations carried out in the presence of an NADPH regenerating system were not detected, being rapidly hydrolyzed by mEH to diols 3. The enantiomeric composition of the latter showed that no enantioface selection occurred in the epoxidation of 1c and 1d, and a very low (8%) ee of the (R)-epoxide was formed from 1b. Incubation of racemic epoxides 2b-d with the microsomal fraction showed that the mEH-catalyzed hydrolysis of 2c and 2d was practically nonenantioselective, while that of 2b exhibited a selectivity E = 4.9 favoring the hydrolysis of the (S)-enantiomer. A comparison of these results with those previously obtained for linear and branched chain alkyl monosubstituted oxiranes shows that the introduction of the second alkyl substituent suppresses the selectivity of the mEH reaction of the latter and reverses that of the former substrates.

Tuning the oxidative power of free iron-sulfur clusters.

PubMed

Lang, Sandra M; Zhou, Shaodong; Schwarz, Helmut

2017-03-15

The gas-phase reactions between a series of di-iron sulfur clusters Fe 2 S x + (x = 1-3) and the small alkenes C 2 H 4 , C 3 H 6 , and C 4 H 8 have been investigated by means of Fourier-transform ion-cyclotron resonance mass spectrometry. For all studied alkenes, the reaction efficiency is found to increase in the order Fe 2 S + < Fe 2 S 2 + < Fe 2 S 3 + . In particular, Fe 2 S + and Fe 2 S 2 + only form simple association products, whereas the sulfur-rich Fe 2 S 3 + is able to dehydrogenate propene and 2-butene via desulfurization of the cluster and formation of H 2 S. This indicates an increased propensity to induce oxidation reactions, i.e. oxidative power, of Fe 2 S 3 + that is attributed to an increased formal oxidation state of the iron atoms. Furthermore, the ability of Fe 2 S 3 + to activate and dissociate the C-H bonds of the alkenes is observed to increase with increasing size of the alkene and thus correlates with the alkene ionization energy.

Exploring between the extremes: conversion-dependent kinetics of phosphite-modified hydroformylation catalysis.

PubMed

Kubis, Christoph; Selent, Detlef; Sawall, Mathias; Ludwig, Ralf; Neymeyr, Klaus; Baumann, Wolfgang; Franke, Robert; Börner, Armin

2012-07-09

The kinetics of the hydroformylation of 3,3-dimethyl-1-butene with a rhodium monophosphite catalyst has been studied in detail. Time-dependent concentration profiles covering the entire olefin conversion range were derived from in situ high-pressure FTIR spectroscopic data for both, pure organic components and catalytic intermediates. These profiles fit to Michaelis-Menten-type kinetics with competitive and uncompetitive side reactions involved. The characteristics found for the influence of the hydrogen concentration verify that the pre-equilibrium towards the catalyst substrate complex is not established. It has been proven experimentally that the hydrogenolysis of the intermediate acyl complex remains rate limiting even at high conversions when the rhodium hydride is the predominant resting state and the reaction is nearly of first order with respect to the olefin. Results from in situ FTIR and high-pressure (HP) NMR spectroscopy and from DFT calculations support the coordination of only one phosphite ligand in the dominating intermediates and a preferred axial position of the phosphite in the electronically saturated, trigonal bipyramidal (tbp)-structured acyl rhodium complex. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Temperature-dependent mid-IR absorption spectra of gaseous hydrocarbons

NASA Astrophysics Data System (ADS)

Klingbeil, Adam E.; Jeffries, Jay B.; Hanson, Ronald K.

2007-10-01

Quantitative mid-IR absorption spectra (2500 3400 cm-1) for 12 pure hydrocarbon compounds are measured at temperatures ranging from 25 to 500 °C using an FTIR spectrometer. The hydrocarbons studied are n-pentane, n-heptane, n-dodecane, 2,2,4-trimethyl-pentane (iso-octane), 2-methyl-butane, 2-methyl-pentane, 2,4,4-trimethyl-1-pentene, 2-methyl-2-butene, propene, toluene, m-xylene, and ethylbenzene. Room-temperature measurements of neat hydrocarbon vapor were made with an instrument resolution of both 0.1 and 1 cm-1 (FWHM) to confirm that the high-resolution setting was required only to resolve the propene absorption spectrum while the spectra of the other hydrocarbons could be resolved with 1 cm-1 resolution. High-resolution (0.1 cm-1), room-temperature measurements of neat hydrocarbons were made at low pressure (˜1 Torr, 133 Pa) and compared to measurements of hydrocarbon/N2 mixtures at atmospheric pressure to verify that no pressure broadening could be observed over this pressure range. The temperature was varied between 25 and 500 °C for atmospheric-pressure measurements of hydrocarbon/N2 mixtures (Xhydrocarbon˜0.06 1.5%) and it was found that the absorption cross section shows simple temperature-dependent behavior for a fixed wavelength over this temperature range. Comparisons with previous FTIR data over a limited temperature range and with high-resolution laser absorption data over a wide temperature range show good agreement.

Simple electronic apparatus for the analysis of radioactively labeled gel electrophoretograms

DOEpatents

Goulianos, Konstantin; Smith, Karen K.; White, Sebastian N.

1982-01-01

A high resolution position sensitive radiation detector for analyzing radiation emanating from a source, constructed of a thin plate having an elongated slot with conductive edges acting as a cathode, a charged anode wire positioned within 0.5 mm adjacent the source and running parallel to the slot and centered therein, an ionizable gas ionized by radiation emanating from the source provided surrounding the anode wire in the slot, a helical wire induction coil serving as a delay line and positioned beneath the anode wire for detecting gas ionization and for producing resulting ionization signals, and processing circuits coupled to the induction coil for receiving ionization signals induced therein after determining therefrom the location along the anode wire of any radiation emanating from the source. An ionization gas of 70% Ar, 29% Isobutane, 0.6% Freon 13BI, and 0.4% Methylal is used.

Distribution, abundance and carbon isotopic composition of gaseous hydrocarbons in Big Soda Lake, Nevada - An alkaline, meromictic lake

NASA Technical Reports Server (NTRS)

Oremland, R. S.; Des Marais, D. J.

1983-01-01

The study of the distribution and isotopic composition of low molecular weight hydrocarbon gases at the Big Soda Lake, Nevada, has shown that while neither ethylene nor propylene were found in the lake, ethane, propane, isobutane and n-butane concentrations all increased with water column depth. It is concluded that methane has a biogenic origin in both the sediments and the anoxic water column, and that C2-C4 alkanes have biogenic origins in the monimolimnion water and shallow sediments. The changes observed in delta C-13/CH4/ and CH4/(C2H6 + C3H8) with depth in the water column and sedimeents are probably due to bacterial processes, which may include anaerobic methane oxidation and different rates of methanogenesis, and C2-to-C4 alkane production by microorganisms.

Hierarchical Macro-meso-microporous ZSM-5 Zeolite Hollow Fibers With Highly Efficient Catalytic Cracking Capability

PubMed Central

Liu, Jia; Jiang, Guiyuan; Liu, Ying; Di, Jiancheng; Wang, Yajun; Zhao, Zhen; Sun, Qianyao; Xu, Chunming; Gao, Jinsen; Duan, Aijun; Liu, Jian; Wei, Yuechang; Zhao, Yong; Jiang, Lei

2014-01-01

Zeolite fibers have attracted growing interest for a range of new applications because of their structural particularity while maintaining the intrinsic performances of the building blocks of zeolites. The fabrication of uniform zeolite fibers with tunable hierarchical porosity and further exploration of their catalytic potential are of great importance. Here, we present a versatile and facile method for the fabrication of hierarchical ZSM-5 zeolite fibers with macro-meso-microporosity by coaxial electrospinning. Due to the synergistic integration of the suitable acidity and the hierarchical porosity, high yield of propylene and excellent anti-coking stability were demonstrated on the as-prepared ZSM-5 hollow fibers in the catalytic cracking reaction of iso-butane. This work may also provide good model catalysts with uniform wall thickness and tunable porosity for studying a series of important catalytic reactions. PMID:25450726

Countercurrent direct contact heat exchange process and system

DOEpatents

Wahl, III, Edward F.; Boucher, Frederic B.

1979-01-01

Recovery of energy from geothermal brines and other hot water sources by direct contact heat exchange with a working fluid, such as a hydrocarbon working fluid, e.g. isobutane. The process and system consists of a plurality of stages, each stage including mixing and settling units. In the first stage, hot brine and arm working fluid are intimately mixed and passed into a settler wherein the brine settles to the bottom of the settler and the hot working fluid rises to the top. The hot working fluid is passed to a heat engine or turbine to produce work and the working fluid is then recycled back into the system. The system is comprised of a series of stages each containing a settler and mixer, and wherein the working fluid and the brine flow in a countercurrent manner through the stages to recover the heat from the brine in increments and raise the temperature of the working fluid in increments.

Prediction of vapour-liquid and vapour-liquid-liquid equilibria of nitrogen-hydrocarbon mixtures used in J-T refrigerators

NASA Astrophysics Data System (ADS)

Narayanan, Vineed; Venkatarathnam, G.

2018-03-01

Nitrogen-hydrocarbon mixtures are widely used as refrigerants in J-T refrigerators operating with mixtures, as well as in natural gas liquefiers. The Peng-Robinson equation of state has traditionally been used to simulate the above cryogenic process. Multi parameter Helmholtz energy equations are now preferred for determining the properties of natural gas. They have, however, been used only to predict vapour-liquid equilibria, and not vapour-liquid-liquid equilibria that can occur in mixtures used in cryogenic mixed refrigerant processes. In this paper the vapour-liquid equilibrium of binary mixtures of nitrogen-methane, nitrogen-ethane, nitrogen-propane, nitrogen-isobutane and three component mixtures of nitrogen-methane-ethane and nitrogen-methane-propane have been studied with the Peng-Robinson and the Helmholtz energy equations of state of NIST REFPROP and compared with experimental data available in the literature.

The adsorption of 1,3-butadiene on Pd/Ni multilayers: The interplay between spin polarization and chemisorption strength

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gomez, Guillermina; Belelli, Patricia G., E-mail: pbelelli@plapiqui.edu.a; Cabeza, Gabriela F.

2010-12-15

The adsorption of 1,3-butadiene (BD) on the Pd/Ni(1 1 1) multilayers has been studied using the VASP method in the framework of the density functional theory (DFT). The adsorption on two different configurations of the Pd{sub n}/Ni{sub m}(1 1 1) systems were considered. The most stable adsorption sites are dependent on the substrate composition and on the inclusion or not of spin polarization. On Pd{sub 1}Ni{sub 3}(1 1 1) surface, di-{pi}-cis and 1,2,3,4-tetra-{sigma} adsorption structures are the most stable for non-spin polarized (NSP) and spin polarized (SP) levels of calculation, respectively. Conversely, on Pd{sub 3}Ni{sub 1}(1 1 1) surface, themore » 1,2,3,4-tetra-{sigma} adsorption structure is the most stable for both NSP and SP levels, respectively. The magnetization of the Pd atoms strongly modifies the adsorption energy of BD and its most stable adsorption mode. On the other hand, as a consequence of BD adsorption, the Pd magnetization decreases. The smaller adsorption energies of BD and 1-butene on the Pd{sub 1}Ni{sub 3}(1 1 1) surface than on Pd(1 1 1) can be associated to the strained Pd overlayer deposited on Ni(1 1 1). -- Graphical Abstract: The adsorption of 1,3-butadiene on Pd/Ni(1 1 1) multilayers was theoretically studied. The most stable adsorption site depends on the substrate composition and on the inclusion of spin polarization. Display Omitted« less

Conversion of 2,3-butanediol to 2-butanol, olefins and fuels

DOEpatents

Lilga, Michael A.; Lee, Guo-Shuh; Lee, Suh-Jane

2016-12-13

Embodiments of an integrated method for step-wise conversion of 2,3-butanediol to 2-butanol, and optionally to hydrocarbons, are disclosed. The method includes providing an acidic catalyst, exposing a composition comprising aqueous 2,3-butanediol to the acidic catalyst to produce an intermediate composition comprising methyl ethyl ketone, providing a hydrogenation catalyst that is spatially separated from the acidic catalyst, and subsequently exposing the intermediate composition to the hydrogenation catalyst to produce a composition comprising 2-butanol. The method may further include subsequently exposing the composition comprising 2-butanol to a deoxygenation catalyst, and deoxygenating the 2-butanol to form hydrocarbons. In some embodiments, the hydrocarbons comprise olefins, such as butenes, and the method may further include subsequently exposing the hydrocarbons to a hydrogenation catalyst to form saturated hydrocarbons.

Effects of carbonate species on the kinetics of dechlorination of 1,1,1-trichloroethane by zero-valent iron.

PubMed

Agrawal, Abinash; Ferguson, William J; Gardner, Bruce O; Christ, John A; Bandstra, Joel Z; Tratnyek, Paul G

2002-10-15

The effect of precipitates on the reactivity of iron metal (Fe0) with 1,1,1-trichloroethane (TCA) was studied in batch systems designed to model groundwaters that contain dissolved carbonate species (i.e., C(IV)). At representative concentrations for high-C(IV) groundwaters (approximately 10(-2) M), the pH in batch reactors containing Fe0 was effectively buffered until most of the aqueous C(IV) precipitated. The precipitate was mainly FeCO3 (siderite) but may also have included some carbonate green rust. Exposure of the Fe0 to dissolved C(IV) accelerated reduction of TCA, and the products formed under these conditions consisted mainly of ethane and ethene, with minor amounts of several butenes. The kinetics of TCA reduction were first-order when C(IV)-enhanced corrosion predominated but showed mixed-order kinetics (zero- and first-order) in experiments performed with passivated Fe0 (i.e., before the onset of pitting corrosion and after repassivation by precipitation of FeCO3). All these data were described by fitting a Michaelis-Menten-type kinetic model and approximating the first-order rate constant as the ratio of the maximum reaction rate (Vm) and the concentration of TCA at half of the maximum rate (K(1/2)). The decrease in Vm/K(1/2) with increasing C(IV) exposure time was fit to a heuristic model assuming proportionality between changes in TCA reduction rate and changes in surface coverage with FeCO3.

Synthesis and Structure of an Extended Cluster Lead(II) Carboxylate, [Pb{(CO)(9)Co(3)(&mgr;(3)-CCO(2))}(2)](n)(). Role of Core Metals in Cluster-Derived Hydrogenation Catalysts.

PubMed

Lei, Xinjian; Shang, Maoyu; Patil, Atul; Wolf, Eduardo E.; Fehlner, Thomas P.

1996-05-22

The reaction of lead acetate with (CO)(9)Co(3)(&mgr;(3)-CCOOH) leads to the formation of [Pb{(CO)(9)Co(3)(&mgr;(3)-CCO(2))}(2)](n)(), I, in high yield. The structure of I exhibits unusual six-coordinate Pb(II) centers with two asymmetrical chelating cluster carboxylates (C(22)Co(6)PbO(22); triclinic P&onemacr;; a = 8.119(1), b = 14.346(2), c = 14.660(2) Å; alpha = 102.18(1), beta = 99.01(1), gamma = 97.30(1) degrees; Z = 2). One oxygen of each cluster carboxylate ligand bridges between adjacent lead atoms such that a chainlike extended structure is found in the solid state without the presence of solvent or water. I is converted stepwise on pyrolysis into two metastable forms of solid materials (designated LT and HT), each of which has been characterized spectroscopically. The hydrogenation of 2-butenal as a test reaction shows that the LT catalyst exhibits selectivities similar to previous LT materials derived from other cobalt cluster metal carboxylates and that the HT material is totally inactive. The observed release of the lead core metal under HT activation conditions totally inactivates the catalyst and demonstrates exposure of the core metal in the HT form of these novel catalysts.

Regio- and Stereospecific Conversion of 4-Alkylphenols by the Covalent Flavoprotein Vanillyl-Alcohol Oxidase

PubMed Central

van den Heuvel, Robert H. H.; Fraaije, Marco W.; Laane, Colja; van Berkel, Willem J. H.

1998-01-01

The regio- and stereospecific conversion of prochiral 4-alkylphenols by the covalent flavoprotein vanillyl-alcohol oxidase was investigated. The enzyme was active, with 4-alkylphenols bearing aliphatic side chains of up to seven carbon atoms. Optimal catalytic efficiency occurred with 4-ethylphenol and 4-n-propylphenols. These short-chain 4-alkylphenols are stereoselectively hydroxylated to the corresponding (R)-1-(4′-hydroxyphenyl)alcohols (F. P. Drijfhout, M. W. Fraaije, H. Jongejan, W. J. H. van Berkel, and M. C. R. Franssen, Biotechnol. Bioeng. 59:171–177, 1998). (S)-1-(4′-Hydroxyphenyl)ethanol was found to be a far better substrate than (R)-1-(4′-hydroxyphenyl)ethanol, explaining why during the enzymatic conversion of 4-ethylphenol nearly no 4-hydroxyacetophenone is formed. Medium-chain 4-alkylphenols were exclusively converted by vanillyl-alcohol oxidase to the corresponding 1-(4′-hydroxyphenyl)alkenes. The relative cis-trans stereochemistry of these reactions was strongly dependent on the nature of the alkyl side chain. The enzymatic conversion of 4-sec-butylphenol resulted in two (4′-hydroxyphenyl)-sec-butene isomers with identical masses but different fragmentation patterns. We conclude that the water accessibility of the enzyme active site and the orientation of the hydrophobic alkyl side chain of the substrate are of major importance in determining the regiospecific and stereochemical outcome of vanillyl-alcohol oxidase-mediated conversions of 4-alkylphenols. PMID:9791114

Non-methane hydrocarbons (NMHCs) and their contribution to ozone formation potential in a petrochemical industrialized city, Northwest China

NASA Astrophysics Data System (ADS)

Jia, Chenhui; Mao, Xiaoxuan; Huang, Tao; Liang, Xiaoxue; Wang, Yanan; Shen, Yanjie; Jiang, Wanyanhan; Wang, Huiqin; Bai, Zhilin; Ma, Minquan; Yu, Zhousuo; Ma, Jianmin; Gao, Hong

2016-03-01

Hourly air concentrations of fifty-three non-methane hydrocarbons (NMHCs) were measured at downtown and suburb of Lanzhou, a petrochemical industrialized city, Northwest China in 2013. The measured data were used to investigate the seasonal characteristics of NMHCs air pollution and their contributions to the ozone formation in Lanzhou. Annually averaged NMHCs concentration was 38.29 ppbv in downtown Lanzhou. Among 53 NMHCs, alkanes, alkenes, and aromatics accounted for 57%, 23% and 20% of the total NMHCs air concentration, respectively. The atmospheric levels of toluene and propane with mean values of 4.62 and 4.56 ppbv were higher than other NMHCs, respectively. The ambient levels of NMHCs in downtown Lanzhou were compared with measured NMHCs data collected at a suburban site of Lanzhou, located near a large-scale petrochemical industry. Results show that the levels of alkanes, alkenes, and aromatics in downtown Lanzhou were lower by factors of 3-11 than that in west suburb of the city. O3-isopleth plots show that ozone was formed in VOCs control area in downtown Lanzhou and NOx control area at the west suburban site during the summertime. Propylene-equivalent (Prop-Equiv) concentration and the maximum incremental reactivity (MIR) in downtown Lanzhou indicate that cis-2-butene, propylene, and m/p-xylene were the first three compounds contributing to ozone formation potentials whereas in the petrochemical industrialized west suburb, ethane, propene, and trans-2-Butene played more important role in the summertime ozone formation. Principal component analysis (PCA) and multiple linear regression (MLR) were further applied to identify the dominant emission sources and examine their fractions in total NMHCs. Results suggest that vehicle emission, solvent usage, and industrial activities were major sources of NMHCs in the city, accounting for 58.34%, 22.19%, and 19.47% of the total monitored NMHCs in downtown Lanzhou, respectively. In the west suburb of the city, however, vehicle emission was less important as compared with sources from petrochemical industries, as characterized by relatively higher ethane (C2H4)/ ethyne (acetylene) and propene (C3H6)/ethyne ratios which ruled out tailpipes emission as major contributors to the VOCs sources.

Thermo-responsive hydroxybutyl chitosan hydrogel as artery intervention embolic agent for hemorrhage control.

PubMed

Sun, Guohui; Feng, Chao; Jiang, Changqing; Zhang, Tingting; Bao, Zixian; Zuo, Yajun; Kong, Ming; Cheng, Xiaojie; Liu, Ya; Chen, Xiguang

2017-12-01

This work targeted to investigate the potential of thermo-responsive hydroxybutyl chitosan (HBC) hydrogel using as an embolic material for occlusion of selective blood vessels. HBC hydrogel was prepared via an etherification reaction between chitosan (CS) and 1, 2-butene oxide. The hydroxybutyl groups were introduced into CS backbone, which endowed HBC hydrogel with properties of porous structure, favorable hydrophilia and rapid sol-gel interconvertibility. The gelation temperatures and gelation time respectively decreased from 30.7°C to 11.5°C and 79.60±3.19s to 7.70±1.42s at 37°C, with HBC solutions viscoelasticity increased from 3.0% to 7.0%. HBC hydrogel exhibited noncytotoxic to mouse embryo fibroblasts (MEFs) and excellent hemocompatibility with red blood cells (RBCs). After injection HBC solution into rat renal arteries, HBC solution transformed into hydrogel and attached onto blood vessel inner wall tightly, giving immediate blood vessels embolization. Meanwhile, RBCs could aggregate around HBC hydrogel to form moderate coagulation, which was beneficial to avoid hydrogel migration with blood flow. Above results suggested that HBC hydrogel could be applied as a promising embolic agent for hemorrage in the interventional vascular embolization field. Copyright © 2017. Published by Elsevier B.V.

An operando FTIR spectroscopic and kinetic study of carbon monoxide pressure influence on rhodium-catalyzed olefin hydroformylation.

PubMed

Kubis, Christoph; Sawall, Mathias; Block, Axel; Neymeyr, Klaus; Ludwig, Ralf; Börner, Armin; Selent, Detlef

2014-09-08

The influence of carbon monoxide concentration on the kinetics of the hydroformylation of 3,3-dimethyl-1-butene with a phosphite-modified rhodium catalyst has been studied for the pressure range p(CO)=0.20-3.83 MPa. Highly resolved time-dependent concentration profiles of the organometallic intermediates were derived from IR spectroscopic data collected in situ for the entire olefin-conversion range. The dynamics of the catalyst and organic components are described by enzyme-type kinetics with competitive and uncompetitive inhibition reactions involving carbon monoxide taken into account. Saturation of the alkyl-rhodium intermediates with carbon monoxide as a cosubstrate occurs between 1.5 and 2 MPa of carbon monoxide pressure, which brings about a convergence of aldehyde regioselectivity. Hydrogenolysis of the acyl intermediate is fast at 30 °C and low pressure of p(CO)=0.2 MPa, but is of minus first order with respect to the solution concentration of carbon monoxide. Resting 18-electron hydrido and acyl complexes that correspond to early and late rate-determining states, respectively, coexist as long as the conversion of the substrate is not complete. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Use of KRS-XE positive chemically amplified resist for optical mask manufacturing

NASA Astrophysics Data System (ADS)

Ashe, Brian; Deverich, Christina; Rabidoux, Paul A.; Peck, Barbara; Petrillo, Karen E.; Angelopoulos, Marie; Huang, Wu-Song; Moreau, Wayne M.; Medeiros, David R.

2002-03-01

The traditional mask making process uses chain scission-type resists such as PBS, poly(butene-1-sulfone), and ZEP, poly(methyl a-chloroacrylate-co-a-methylstyrene) for making masks with dimensions greater than 180nm. PBS resist requires a wet etch process to produce patterns in chrome. ZEP was employed for dry etch processing to meet the requirements of shrinking dimensions, optical proximity corrections and phase shift masks. However, ZEP offers low contrast, marginal etch resistance, organic solvent development, and concerns regarding resist heating with its high dose requirements1. Chemically Amplified Resist (CAR) systems are a very good choice for dimensions less than 180nm because of their high sensitivity and contrast, high resolution, dry etch resistance, aqueous development, and process latitude2. KRS-XE was developed as a high contrast CA resist based on ketal protecting groups that eliminate the need for post exposure bake (PEB). This resist can be used for a variety of electron beam exposures, and improves the capability to fabricate masks for devices smaller than 180nm. Many factors influence the performance of resists in mask making such as post apply bake, exposure dose, resist develop, and post exposure bake. These items will be discussed as well as the use of reactive ion etching (RIE) selectivity and pattern transfer.

Combustion modeling and kinetic rate calculations for a stoichiometric cyclohexane flame. 1. Major reaction pathways.

PubMed

Zhang, Hongzhi R; Huynh, Lam K; Kungwan, Nawee; Yang, Zhiwei; Zhang, Shaowen

2007-05-17

The Utah Surrogate Mechanism was extended in order to model a stoichiometric premixed cyclohexane flame (P = 30 Torr). Generic rates were assigned to reaction classes of hydrogen abstraction, beta scission, and isomerization, and the resulting mechanism was found to be adequate in describing the combustion chemistry of cyclohexane. Satisfactory results were obtained in comparison with the experimental data of oxygen, major products and important intermediates, which include major soot precursors of C2-C5 unsaturated species. Measured concentrations of immediate products of fuel decomposition were also successfully reproduced. For example, the maximum concentrations of benzene and 1,3-butadiene, two major fuel decomposition products via competing pathways, were predicted within 10% of the measured values. Ring-opening reactions compete with those of cascading dehydrogenation for the decomposition of the conjugate cyclohexyl radical. The major ring-opening pathways produce 1-buten-4-yl radical, molecular ethylene, and 1,3-butadiene. The butadiene species is formed via beta scission after a 1-4 internal hydrogen migration of 1-hexen-6-yl radical. Cascading dehydrogenation also makes an important contribution to the fuel decomposition and provides the exclusive formation pathway of benzene. Benzene formation routes via combination of C2-C4 hydrocarbon fragments were found to be insignificant under current flame conditions, inferred by the later concentration peak of fulvene, in comparison with benzene, because the analogous species series for benzene formation via dehydrogenation was found to be precursors with regard to parent species of fulvene.

Purification and characterization of two enone reductases from Saccharomyces cerevisiae.

PubMed

Wanner, P; Tressl, R

1998-07-01

Two enone reductases catalyzing irreversibly the enantioselective reduction of alpha,beta-unsaturated carbonyls have been purified 165-fold and 257-fold, respectively, from the cytosolic fraction of Saccharomyces cerevisiae by means of streptomycin sulfate treatment, Sephadex G-25 filtration, DEAE-Sepharose CL-6B chromatography, blue Sepharose CL-6B chromatography and Superdex 200 preparation-grade filtration. One enzyme (E I) was NADPH-dependent, showed a molecular mass of 75 kDa and decomposed under denaturing electrophoretic conditions into two subunits of 34 kDa and 37 kDa. The other enzyme (E II) was NADH linked and the molecular mass estimated by means of Superdex 200 preparation-grade filtration, was 130 kDa. The enzyme decomposed into subunits of 56 kDa and 64 kDa on SDS/PAGE. Both enzymes were most active at pH 4.8 and accepted 1-octen-3-one, 1-hexen-3-one, 3-alken-2-ones, 4-alken-3-ones, 2-cyclohexen-1-ones, 2-alkenals, 2,4-alkadienals, 2-phenyl-2-alkenals, and 2-alkyl-2-alkenals as substrates. Both enzymes showed their highest activities with 1-hexen-3-one and 1-octen-3-one, respectively. The Km values for 1-octen-3-one were estimated as 0.54 mM (E I) and 0.20 mM (E II), respectively. Both enzymes catalyzed the enantioselective reduction of cis- and trans-2-phenyl-2-butenal into (R)-2-phenylbutanal.

Photochemical cycloaddition reactions of cyanoacetylene and dicyanoacetylene

NASA Technical Reports Server (NTRS)

Ferris, J. P.; Guillemin, J. C.

1990-01-01

Photolysis of cyanoacetylene with 185- or 206-nm light yields 1,3,5-tricyanobenzene while 254-nm radiation yields a mixture of tetracyanocyclooctatetraenes, 1,2,4- and 1,3,5-tricyanobenzene. A polymer of cyanoacetylene is the major photoproduct. 1,3,5-Tricarbomethoxybenzene was the only photoproduct identified from the irradiation of methyl propiolate at 254 nm. Mono-, di-, and tricyanobenzenes are formed by irradiation of mixtures of acetylene and cyanoacetylene at 185, 206, and 254 nm along with trace amounts of cyclooctatetraenes. No photoadducts were detected on photolysis of mixtures of cyanoacetylene and CO or HCN. The tetracyanocyclooctatetraene structures were established by UV, MS, and NMR analyses. The 1H NMR of the product mixture exhibited a singlet at delta 7.028 consistent with either 1 or 2 and two singlets at delta 6.85 and 6.91 assigned to 3. Photolysis of mixtures of dicyanoacetylene and acetylene with either 185- or 206-nm light yielded 1,2-dicyanobenzene and (E,Z)-1-buten-3-yne-1,4-dicarbonitrile. These products were also obtained using 254-nm light along with a mixture of tetracyanocyclooctatetraenes. The same three singlets were observed in this product mixture as were observed in the tetracyanocyclooctatetraenes obtained from cyanoacetylene. From this observation it was concluded that the delta 7.02 signal is due to 2 and not 1. The photolysis of cyanoacetylene and dicyanoacetylene in the presence of ethylene with 185-nm light yields 1-cyanocylobutene and 1,2-dicyanocyclobutene, respectively. 2-Cyanobutadiene and 2,3-dicyanobutadiene are the photoproducts with 254-nm light. Reaction pathways are proposed to explain these findings.

New analytical method for the determination of styrene oligomers formed from polystyrene decomposition and its application at the coastlines of the North-West Pacific ocean.

PubMed

Saido, Katsuhiko; Koizumi, Koshiro; Sato, Hideto; Ogawa, Naoto; Kwon, Bum Gun; Chung, Seon-Yong; Kusui, Takashi; Nishimura, Masahiko; Kodera, Yoichi

2014-03-01

The pollution caused by plastic debris is an environmental problem with increasing concern in the oceans. Among the plastic polymers, polystyrene (PS) is one of the most problematic plastics due to the direct public health risk associated with their dispersion, as well as the numerous adverse environmental impacts which arise both directly from the plastics and from their degradation products. Little is known about their potential distribution characteristics throughout the oceans. For the first time, we report here on the regional distribution of styrene monomer (SM), styrene dimers (SD; 2,4-diphenyl-1-butene, SD1; 1,3-diphenyl propane, SD2), and styrene trimer (2,4,6-triphenyl-1-hexene: ST1), as products of PS decomposition determined from samples of sand and seawater from the shorelines of the North-West Pacific ocean. In order to quantitatively determine SM, SD (=SD1+SD2), and ST1, a new analytical method was developed. The detection limit was 3.3 μg L(-1), based on a signal-to-noise ratio of three, which was well-suited to quantify levels of SM, SD, and ST1 in samples. Surprisingly, the concentrations of SM, SD, and ST1 in sand samples from the shorelines were consistently greater than those in seawater samples from the same location. The results of this study suggest that SM, SD, and ST1 can be widely dispersed throughout the North-West Pacific oceans. Copyright © 2013 Elsevier B.V. All rights reserved.

Effect of unsaturation on the absorption of ethane and ethylene in imidazolium-based ionic liquids.

PubMed

Moura, Leila; Mishra, Manas; Bernales, Varinia; Fuentealba, Patricio; Padua, Agilio A H; Santini, Catherine C; Costa Gomes, Margarida F

2013-06-20

The influence of the presence of imidazolium side chain unsaturation on the solubility of ethane and ethylene was studied in three ionic liquids: 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide-saturated alkyl side-chain in the cation; 1-methyl-3-(buten-3-yl)imidazolium bis(trifluorosulfonyl)imide-double bond in the side-chain of the cation; and 1-methyl-3-benzylimidazolium bis(trifluorosulfonyl)imide-benzyl group in the side-chain of the cation. The solubility of both gases decreases when the side-chain of the cations is functionalized with an unsaturated group. This can be explained by a less favorable enthalpy of solvation. The difference of solubility between ethane and ethylene can be explained from a balance of enthalpic and entropic factors: for the ionic liquid with the saturated alkyl side-chain and the benzyl-substituted side-chain, it is the favorable entropy of solvation that explains the larger ethylene solubility, whereas in the case of the saturated side-chain, it is the more favorable enthalpy of solvation. Molecular simulation allowed the identification of the mechanisms of solvation and the preferential solvation sites for each gas in the different ionic liquids. Simulations have shown that the entropy of solvation is more favorable when the presence of the gas weakens the cation-anion interactions or when the gas can be solvated near different sites of the ionic liquid.

Kinetic and thermodynamic selectivity of intermolecular C-H activation at [Tp'Rh(PMe3)]. How does the ancillary ligand affect the metal-carbon bond strength?

PubMed

Jiao, Yunzhe; Morris, James; Brennessel, William W; Jones, William D

2013-10-30

Tp'Rh(PMe3)(CH3)H was synthesized as a precursor to produce the coordinatively unsaturated fragment [Tp'Rh(PMe3)], which reacts with benzene, mesitylene, 3,3-dimethyl-1-butene, 2-methoxy-2-methylpropane, 2-butyne, acetone, pentane, cyclopentane, trifluoroethane, fluoromethane, dimethyl ether, and difluoromethane at ambient temperature to give only one product in almost quantitative yield in each case. All of the complexes Tp'Rh(PMe3)(R)H were characterized by NMR spectroscopy, and their halogenated derivatives were fully characterized by NMR spectroscopy, elemental analysis, and X-ray crystallography. The active species [Tp'Rh(PMe3)] was also able to activate the alkynyl C-H bond of terminal alkynes to give activation products of the type Tp'Rh(PMe3)(C≡CR)H (R = t-Bu, SiMe3, hexyl, CF3, Ph, p-MeOC6H4, and p-CF3C6H4). The measured relative rhodium-carbon bond strengths display two linear correlations with the corresponding carbon-hydrogen bond strengths, giving a slope of 1.54 for α-unsubstituted hydrocarbons and a slope of 1.71 for substrates with α-substitution. Similar trends of energy correlations were established by DFT calculated metal-carbon bond strengths for the same groups of substrates.

On the Radiolysis of Ethylene Ices by Energetic Electrons and Implications to the Extraterrestrial Hydrocarbon Chemistry

NASA Astrophysics Data System (ADS)

Zhou, Li; Maity, Surajit; Abplanalp, Matt; Turner, Andrew; Kaiser, Ralf I.

2014-07-01

The chemical processing of ethylene ices (C2H4) by energetic electrons was investigated at 11 K to simulate the energy transfer processes and synthesis of new molecules induced by secondary electrons generated in the track of galactic cosmic ray particles. A combination of Fourier transform infrared spectrometry (solid state) and quadrupole mass spectrometry (gas phase) resulted in the identification of six hydrocarbon molecules: methane (CH4), the C2 species acetylene (C2H2), ethane (C2H6), the ethyl radical (C2H5), and—for the very first time in ethylene irradiation experiments—the C4 hydrocarbons 1-butene (C4H8) and n-butane (C4H10). By tracing the temporal evolution of the newly formed molecules spectroscopically online and in situ, we were also able to fit the kinetic profiles with a system of coupled differential equations, eventually providing mechanistic information, reaction pathways, and rate constants on the radiolysis of ethylene ices and the inherent formation of smaller (C1) and more complex (C2, C4) hydrocarbons involving carbon-hydrogen bond ruptures, atomic hydrogen addition processes, and radical-radical recombination pathways. We also discuss the implications of these results on the hydrocarbon chemistry on Titan's surface and on ice-coated, methane-bearing interstellar grains as present in cold molecular clouds such as TMC-1.

Evaluation of serum and liver toxicokinetics for furan and liver DNA adduct formation in male Fischer 344 rats.

PubMed

Churchwell, M I; Scheri, R C; Von Tungeln, L S; Gamboa da Costa, G; Beland, F A; Doerge, D R

2015-12-01

Furan is a food processing contaminant found in many common cooked foods that induces liver toxicity and liver cancer in animal models treated with sufficient doses. The metabolism of furan occurs primarily in the liver where CYP 2E1 produces a highly reactive bis-electrophile, cis-2-butene-1,4-dial (BDA). BDA reacts with nucleophilic groups in amino acids and DNA in vitro to form covalent adducts. Evidence for BDA-nucleoside adduct formation in vivo is limited but important for assessing the carcinogenic hazard of dietary furan. This study used controlled dosing with furan in Fischer 344 rats to measure serum and liver toxicokinetics and the possible formation of BDA-nucleoside adducts in vivo. After gavage exposure, furan concentrations in the liver were consistently higher than those in whole blood (∼6-fold), which is consistent with portal vein delivery of a lipophilic compound into the liver. Formation of BDA-2'-deoxycytidine in furan-treated rat liver DNA was not observed using LC/MS/MS after single doses as high as 9.2 mg/kg bw or repeated dosing for up to 360 days above a consistent background level (1-2 adducts per 10(8) nucleotides). This absence of BDA-nucleoside adduct formation is consistent with the general lack of evidence for genotoxicity of furan in vivo. Published by Elsevier Ltd.

An extended baseline examination of indoor VOCs in a city of low ambient pollution: Perth, Western Australia

NASA Astrophysics Data System (ADS)

Maisey, S. J.; Saunders, S. M.; West, N.; Franklin, P. J.

2013-12-01

This study of indoor air quality reports VOC concentrations in 386 suburban homes located in Perth Western Australia, a city of low ambient pollution and temperate climate. Details of indoor VOC concentrations, temperature, relative humidity, and information on house characteristics and occupant activities were collected during the sampling periods. The concentration of VOCs observed in typical homes was low and individual compounds rarely exceeded 5 μg m-3. Median individual VOC concentrations ranged from 0.06 μg m-3 for 1,1,1 trichloroethane and butyl ether to 26.6 μg m-3 for cis/trans 2-butene. Recently renovated homes had higher concentrations of VOCs than non renovated homes, including ∑VOCs (p = 0.026), ∑BTEX (p = 0.03), ∑xylene (p = 0.013), toluene (p = 0.05), cyclohexane (p = 0.039), and propyl benzene (p = 0.039). Statistical analyses showed house age and attached garages were not significant factors for any of the VOCs tested. The concentrations of indoor VOCs in Perth were lower than overseas observations and those reported in recent Australian studies, with inferences made to differences in the climate and the occupant behaviour. The results are a baseline profile of indoor VOCs over the period 2006-2011, in an Australian city of low population density and of generally low ambient pollution.

Quantifying alkane emissions in the Eagle Ford Shale using boundary layer enhancement

NASA Astrophysics Data System (ADS)

Roest, Geoffrey; Schade, Gunnar

2017-09-01

The Eagle Ford Shale in southern Texas is home to a booming unconventional oil and gas industry, the climate and air quality impacts of which remain poorly quantified due to uncertain emission estimates. We used the atmospheric enhancement of alkanes from Texas Commission on Environmental Quality volatile organic compound monitors across the shale, in combination with back trajectory and dispersion modeling, to quantify C2-C4 alkane emissions for a region in southern Texas, including the core of the Eagle Ford, for a set of 68 days from July 2013 to December 2015. Emissions were partitioned into raw natural gas and liquid storage tank sources using gas and headspace composition data, respectively, and observed enhancement ratios. We also estimate methane emissions based on typical ethane-to-methane ratios in gaseous emissions. The median emission rate from raw natural gas sources in the shale, calculated as a percentage of the total produced natural gas in the upwind region, was 0.7 % with an interquartile range (IQR) of 0.5-1.3 %, below the US Environmental Protection Agency's (EPA) current estimates. However, storage tanks contributed 17 % of methane emissions, 55 % of ethane, 82 % percent of propane, 90 % of n-butane, and 83 % of isobutane emissions. The inclusion of liquid storage tank emissions results in a median emission rate of 1.0 % (IQR of 0.7-1.6 %) relative to produced natural gas, overlapping the current EPA estimate of roughly 1.6 %. We conclude that emissions from liquid storage tanks are likely a major source for the observed non-methane hydrocarbon enhancements in the Northern Hemisphere.

Improvements in a chemiluminescent ozone analyzer for respiratory applications

NASA Astrophysics Data System (ADS)

Ben-Jebria, Abdellaziz; Hu, Shu-Chieh; Ultman, James S.

1990-11-01

The performance characteristics of a previously developed analyzer utilizing the homogeneous chemiluminescent reaction of ozone (O3) with a stoichiometric excess of 2-methyl-2-butene were improved with the eventual goal of measuring the distribution of O3 in a single human breath. By increasing the sampling flow from 200 to 400 ml/min and utilizing a combination of analog and digital filtering, it was possible to improve the signal-to-noise ratio at 0.5 ppm O3 from 5.5 to 28, the minimum detection limit from 0.02 to 0.01 ppm, the sensitivity from 1.5 to 2.3 na/ppm, and the 10%-90% step-response time from 200 to 100 ms. Humidity, temperature, and inlet gas composition interferences were also evaluated. While temperature and humidity have no influence on the analyzer output, the substitution of carbon dioxide for oxygen increased the analyzer sensitivity by 3.8% for each percent of CO2 that was present. Thus, provided that an appropriate correction for carbon dioxide is made, these improvements allow the instrument to monitor inhaled and exhaled O3 concentrations with a rapid dynamic response and over a broad range of physiologically relevant values.

The Chemistry of Beer Instability

NASA Astrophysics Data System (ADS)

Stewart, Graham G.

2004-07-01

Compared to most other alcoholic beverages, beer is unique because it is unstable when in the final package. This instability can be divided into biological and nonbiological instability. Nonbiological stability of beer involves a wide range of chemical processes and can be considered in a number of categories: physical, flavor, light, foam, and gushing. It is the balance between flavanoid polyphenols (tannoids) and sensitive proteins that specifically combine with polyphenols to form haze that largely dictates physical stability. The flavor stability of beer primarily depends on the oxygen concentration of packaged beer but is influenced by all stages of the brewing process. Foam stability in a glass of beer reflects the quality of the beverage. The backbone of foam is hydrophobic polypeptides. Novel brewing processes such as high-gravity brewing result in a disproportionate loss of these polypeptides and have a negative effect on the foam stability of the resulting beer. Beer is light sensitive, especially in the 350 500 nm range. Beer exposed to this wavelength range in clear or green glass containers quickly develop nauseous skunky-like off-flavors resulting from the formation of 3-methyl-2-butene-1-thiol. Methods of enhancing all of these types of beer stability are discussed.

Covalent modification of cytochrome c by reactive metabolites of furan.

PubMed

Phillips, Martin B; Sullivan, Mathilde M; Villalta, Peter W; Peterson, Lisa A

2014-01-21

Metabolism of the hepatotoxicant furan leads to protein adduct formation in the target organ. The initial bioactivation step involves cytochrome P450-catalyzed oxidation of furan, generating cis-2-butene-1,4-dial (BDA). BDA reacts with lysine to form pyrrolin-2-one adducts. Metabolic studies indicate that BDA also reacts with glutathione (GSH) to generate 2-(S-glutathionyl)butanedial (GSH-BDA), which then reacts with lysine to form GSH-BDA-lysine cross-links. To explore the relative reactivity of these two reactive intermediates, cytochrome c was reacted with BDA in the presence and absence of GSH. As judged by MALDI-TOF mass spectrometry, BDA reacts extensively with cytochrome c to form adducts that add 66 Da to the protein, consistent with the formation of pyrrolinone adducts. Addition of GSH to the reaction mixture reduced the overall extent of adduct formation. The mass of the adducted protein was shifted by 355 Da as expected for GSH-BDA-protein cross-link formation. LC-MS/MS analysis of the tryptic digests of the alkylated protein indicated that the majority of adducts occurred on lysine residues, with BDA reacting less selectively than GSH-BDA. Both types of adducts may contribute to the toxic effects of furan.

Covalent Modification of Cytochrome C by Reactive Metabolites of Furan

PubMed Central

Phillips, Martin B.; Sullivan, Mathilde M.; Villalta, Peter W.; Peterson, Lisa A.

2014-01-01

Metabolism of the hepatotoxicant furan leads to protein adduct formation in the target organ. The initial bioactivation step involves cytochrome P450-catalyzed oxidation of furan, generating cis-2-butene-1,4-dial (BDA). BDA reacts with lysine to form pyrrolin-2-one adducts. Metabolic studies indicate that BDA also reacts with glutathione (GSH) to generate 2-(S-glutathionyl)butanedial (GSH-BDA), which then reacts with lysine to form GSH-BDA-lysine cross-links. To explore the relative reactivity of these two reactive intermediates, cytochrome c was reacted with BDA in the presence and absence of GSH. As judged by MALDI-TOF mass spectrometry, BDA reacts extensively with cytochrome c to form adducts that add 66 Da to the protein, consistent with the formation of pyrrolinone adducts. Addition of GSH to the reaction mixture reduced the overall extent of adduct formation. The mass of the adducted protein was shifted by 355 Da as expected for GSH-BDA-protein cross-link formation. LC-MS/MS analysis of the tryptic digests of the alkylated protein indicated that the majority of adducts occurred on lysine residues, with BDA reacting less selectively than GSH-BDA. Both types of adducts may contribute to the toxic effects of furan. PMID:24364757

Catalytic conversion of light alkanes, Phase 3. Topical report, January 1990--December 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The mission of this work is to devise a new catalyst which can be used in the first simple, economic process to convert the light alkanes in natural gas to an alcohol-rich oxygenated product which can either be used as an environmentally friendly, high-performance liquid fuel, or a precursor to a liquid hydrocarbon transportation fuel. The authors have entered the proof-of-concept stage for converting isobutane to tert butyl alcohol in a practical process and are preparing to enter proof-of-concept of a propane to isopropyl alcohol process in the near future. Methane and ethane are more refractory and thus more difficultmore » to oxidize than the C{sub 3} and C{sub 4} hydrocarbons. Nonetheless, advances made in this area indicate that further research progress could achieve the goal of their direct conversion to alcohols. Progress in Phase 3 catalytic vapor phase methane and ethane oxidation over metals in regular oxidic lattices are the subject of this topical report.« less

The spark discharge synthesis of amino acids from various hydrocarbons

NASA Technical Reports Server (NTRS)

Ring, D.; Miller, S. L.

1984-01-01

The spark discharge synthesis of amino acids using an atmosphere of CH4+N2+H2O+NH3 has been investigated with variable pNH3. The amino acids produced using higher hydrocarbons (ethane, ethylene, acetylene, propane, butane, and isobutane) instead of CH4 were also investigated. There was considerable range in the absolute yields of amino acids, but the yields relative to glycine (or alpha-amino-n-butyric acid) were more uniform. The relative yields of the C3 to C6 aliphatic alpha-amino acids are nearly the same (with a few exceptions) with all the hydrocarbons. The glycine yields are more variable. The precursors to the C3-C6 aliphatic amino acids seem to be produced in the same process, which is separate from the synthesis of glycine precursors. It may be possible to use these relative yields as a signature for a spark discharge synthesis provided corrections can be made for subsequent decomposition events (e.g. in the Murchison meteorite).

Catalytic Hydrogenation Activity and Electronic Structure Determination of Bis(arylimidazol-2-ylidene)pyridine Cobalt Alkyl and Hydride Complexes

PubMed Central

Yu, Renyuan Pony; Darmon, Jonathan M.; Milsmann, Carsten; Margulieux, Grant W.; E. Stieber, S. Chantal; DeBeer, Serena

2013-01-01

The bis(arylimidazol-2-ylidene)pyridine cobalt methyl complex, (iPrCNC)CoCH3, was evaluated for the catalytic hydrogenation of alkenes. At 22 °C and 4 atm of H2 pressure, (iPrCNC)CoCH3 is an effective pre-catalyst for the hydrogenation of sterically hindered, unactivated alkenes such as trans-methylstilbene, 1-methyl-1-cyclohexene and 2,3-dimethyl-2-butene, representing one of the most active cobalt hydrogenation catalysts reported to date. Preparation of the cobalt hydride complex, (iPrCNC)CoH was accomplished by hydrogenation of (iPrCNC)CoCH3. Over the course of 3 hours at 22 °C, migration of the metal-hydride to the 4-position of the pyridine ring yielded (4-H2-iPrCNC)CoN2. Similar alkyl migration was observed upon treatment of (iPrCNC)CoH with 1,1-diphenylethylene. This reactivity raised the question as to whether this class of chelate is redoxactive, engaging in radical chemistry with the cobalt center. A combination of structural, spectroscopic and computational studies was conducted and provided definitive evidence for bis(arylimidazol-2-ylidene)pyridine radicals in reduced cobalt chemistry. Spin density calculations established that the radicals were localized on the pyridine ring, accounting for the observed reactivity and suggest a wide family of pyridine-based pincers may also be redox active. PMID:23968297

Catalytic hydrogenation activity and electronic structure determination of bis(arylimidazol-2-ylidene)pyridine cobalt alkyl and hydride complexes.

PubMed

Yu, Renyuan Pony; Darmon, Jonathan M; Milsmann, Carsten; Margulieux, Grant W; Stieber, S Chantal E; DeBeer, Serena; Chirik, Paul J

2013-09-04

The bis(arylimidazol-2-ylidene)pyridine cobalt methyl complex, ((iPr)CNC)CoCH3, was evaluated for the catalytic hydrogenation of alkenes. At 22 °C and 4 atm of H2 pressure, ((iPr)CNC)CoCH3 is an effective precatalyst for the hydrogenation of sterically hindered, unactivated alkenes such as trans-methylstilbene, 1-methyl-1-cyclohexene, and 2,3-dimethyl-2-butene, representing one of the most active cobalt hydrogenation catalysts reported to date. Preparation of the cobalt hydride complex, ((iPr)CNC)CoH, was accomplished by hydrogenation of ((iPr)CNC)CoCH3. Over the course of 3 h at 22 °C, migration of the metal hydride to the 4-position of the pyridine ring yielded (4-H2-(iPr)CNC)CoN2. Similar alkyl migration was observed upon treatment of ((iPr)CNC)CoH with 1,1-diphenylethylene. This reactivity raised the question as to whether this class of chelate is redox-active, engaging in radical chemistry with the cobalt center. A combination of structural, spectroscopic, and computational studies was conducted and provided definitive evidence for bis(arylimidazol-2-ylidene)pyridine radicals in reduced cobalt chemistry. Spin density calculations established that the radicals were localized on the pyridine ring, accounting for the observed reactivity, and suggest that a wide family of pyridine-based pincers may also be redox-active.

Calculation of a double reactive azeotrope using stochastic optimization approaches

NASA Astrophysics Data System (ADS)

Mendes Platt, Gustavo; Pinheiro Domingos, Roberto; Oliveira de Andrade, Matheus

2013-02-01

An homogeneous reactive azeotrope is a thermodynamic coexistence condition of two phases under chemical and phase equilibrium, where compositions of both phases (in the Ung-Doherty sense) are equal. This kind of nonlinear phenomenon arises from real world situations and has applications in chemical and petrochemical industries. The modeling of reactive azeotrope calculation is represented by a nonlinear algebraic system with phase equilibrium, chemical equilibrium and azeotropy equations. This nonlinear system can exhibit more than one solution, corresponding to a double reactive azeotrope. The robust calculation of reactive azeotropes can be conducted by several approaches, such as interval-Newton/generalized bisection algorithms and hybrid stochastic-deterministic frameworks. In this paper, we investigate the numerical aspects of the calculation of reactive azeotropes using two metaheuristics: the Luus-Jaakola adaptive random search and the Firefly algorithm. Moreover, we present results for a system (with industrial interest) with more than one azeotrope, the system isobutene/methanol/methyl-tert-butyl-ether (MTBE). We present convergence patterns for both algorithms, illustrating - in a bidimensional subdomain - the identification of reactive azeotropes. A strategy for calculation of multiple roots in nonlinear systems is also applied. The results indicate that both algorithms are suitable and robust when applied to reactive azeotrope calculations for this "challenging" nonlinear system.

Comparative techno-economic analysis and process design for indirect liquefaction pathways to distillate-range fuels via biomass-derived oxygenated intermediates upgrading: Liquid Transportation Fuel Production via Biomass-derived Oxygenated Intermediates Upgrading

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, Eric C. D.; Snowden-Swan, Lesley J.; Talmadge, Michael

This paper presents a comparative techno-economic analysis (TEA) of five conversion pathways from biomass to gasoline-, jet-, and diesel-range hydrocarbons via indirect liquefaction with specific focus on pathways utilizing oxygenated intermediates. The four emerging pathways of interest are compared with one conventional pathway (Fischer-Tropsch) for the production of the hydrocarbon blendstocks. The processing steps of the four emerging pathways include: biomass to syngas via indirect gasification, gas cleanup, conversion of syngas to alcohols/oxygenates followed by conversion of alcohols/oxygenates to hydrocarbon blendstocks via dehydration, oligomerization, and hydrogenation. Conversion of biomass-derived syngas to oxygenated intermediates occurs via three different pathways, producing: 1)more » mixed alcohols over a MoS2 catalyst, 2) mixed oxygenates (a mixture of C2+ oxygenated compounds, predominantly ethanol, acetic acid, acetaldehyde, ethyl acetate) using an Rh-based catalyst, and 3) ethanol from syngas fermentation. This is followed by the conversion of oxygenates/alcohols to fuel-range olefins in two approaches: 1) mixed alcohols/ethanol to 1-butanol rich mixture via Guerbet reaction, followed by alcohol dehydration, oligomerization, and hydrogenation, and 2) mixed oxygenates/ethanol to isobutene rich mixture and followed by oligomerization and hydrogenation. The design features a processing capacity of 2,000 tonnes/day (2,205 short tons) of dry biomass. The minimum fuel selling prices (MFSPs) for the four developing pathways range from $3.40 to $5.04 per gasoline-gallon equivalent (GGE), in 2011 US dollars. Sensitivity studies show that MFSPs can be improved with co-product credits and are comparable to the commercial Fischer-Tropsch benchmark ($3.58/GGE). Overall, this comparative TEA study documents potential economics for the developmental biofuel pathways via mixed oxygenates.« less

Experimental and modeling study of the thermal decomposition of methyl decanoate

PubMed Central

Herbinet, Olivier; Glaude, Pierre-Alexandre; Warth, Valérie; Battin-Leclerc, Frédérique

2013-01-01

The experimental study of the thermal decomposition of methyl decanoate was performed in a jet-stirred reactor at temperatures ranging from 773 to 1123 K, at residence times between 1 and 4 s, at a pressure of 800 Torr (106.6 kPa) and at high dilution in helium (fuel inlet mole fraction of 0.0218). Species leaving the reactor were analyzed by gas chromatography. Main reaction products were hydrogen, carbon oxides, small hydrocarbons from C1 to C3, large 1-olefins from 1-butene to 1-nonene, and unsaturated esters with one double bond at the end of the alkyl chain from methyl-2-propenoate to methyl-8-nonenoate. At the highest temperatures, the formation of polyunsaturated species was observed: 1,3-butadiene, 1,3-cyclopentadiene, benzene, toluene, indene, and naphthalene. These results were compared with previous ones about the pyrolysis of n-dodecane, an n-alkane of similar size. The reactivity of both molecules was found to be very close. The alkane produces more olefins while the ester yields unsaturated oxygenated compounds. A detailed kinetic model for the thermal decomposition of methyl decanoate has been generated using the version of software EXGAS which was updated to take into account the specific chemistry involved in the oxidation of methyl esters. This model contains 324 species and 3231 reactions. It provided a very good prediction of the experimental data obtained in jet-stirred reactor. The formation of the major products was analyzed. The kinetic analysis showed that the retro-ene reactions of intermediate unsaturated methyl esters are of importance in low reactivity systems. PMID:23710078

Synthesis of carbon nanoparticles from commercially available liquified petroleum gas

NASA Astrophysics Data System (ADS)

Nandiyanto, A. B. D.; Fadhlulloh, M. A.; Rahman, T.; Mudzakir, A.

2016-04-01

The aim of this study was to synthesize carbon nanoparticles (CNPs) from commercially available liquefied petroleum gas (LPG). In the research procedure, LPG was reacted with air to construct CNPs. To confirm the successful synthesis of CNPs, we conducted several sample analyses: Gas Chromatography-Mass Spectrometry (GC-MS), Transmission Electron Microscope (TEM), X-ray Diffraction (XRD), and Infrared Spectra (FTIR). We also varied LPG and oxygen mole ratios at 0.8; 2.4; 4.8; and 7.2. The GC-MS results indicated the composition of LPG was propane (58.90%), isobutane (18.35%), butane (22.26%), and butane, 2-methyl (0.48%). The TEM results showed that the particles were spheres with sizes of between 25 and 35 nm. The sizes of particles were controllable, depending on the mole ratio. The XRD results showed mole ratios of LPG and oxygen of 0.80 and 2.40 were natural graphite, whereas the mole ratios of 4.80 and 7.20 were hexagonal graphite. FT-IR results showed CNPs have absorption peaks at wave number (i) 752 (C-H bend sp2); (ii) 835 (C=C); (iii) 1274 (C-O-C vibration); (iv) 1400 and 1600 (C-C stretch aromatic); (v) 2800 (C-H sp2); (vi) 2900 (CH sp3); (vii) 3100 (C-H aromatic); and (viii) 3400 cm-1 (O-H). From the FTIR analysis results, the sample contained allotrope graphite due to detection of peaks at 1400 and 1600 cm-1 (C-C stretch aromatic) and 3100 cm-1 (C-H aromatic).

Facile Synthesis and Catalysis of Pure-Silica and Heteroatom LTA

DOE PAGES

Boal, Ben W.; Schmidt, Joel E.; Deimund, Mark A.; ...

2015-11-05

Zeolite A (LTA) has many large-scale uses in separations and ion exchange applications. Because of the high aluminum content and lack of high-temperature stability, applications in catalysis, while highly desired, have been extremely limited. Herein, we report a robust method to prepare pure-silica, aluminosilicate (product Si/Al = 12–42), and titanosilicate LTA in fluoride media using a simple, imidazolium- based organic structure-directing agent. The aluminosilicate material is an active catalyst for the methanol-to-olefins reaction with higher product selectivities to butenes as well as C 5 and C 6 products than the commercialized silicoalumniophosphate or zeolite analogue that both have the chabazitemore » framework (SAPO- 34 and SSZ-13, respectively). Furthermore, the crystal structures of the as-made and calcined pure-silica materials were solved using singlecrystal X-ray diffraction, providing information about the occluded organics and fluoride as well as structural information.« less

The widetilde{A}←widetilde{X} ABSORPTION SPECTRUM OF 2-NITROOXYBUTYL PEROXY RADICAL

NASA Astrophysics Data System (ADS)

Eddingsaas, Nathan; Takematsu, Kana; Okumura, Mitchio

2009-06-01

The nitrate radical is an important atmospheric oxidant in the nighttime sky. Nitrate radicals react by addition to alkenes, and in the presence of oxygen form nitrooxyalkyl peroxy radicals. The peroxy radical formed from the reaction of 2-butene, nitrate radical, and oxygen was detected by cavity ringdown spectroscopy (CRDS) via its widetilde{A}←widetilde{X} electronic absorption spectrum. The widetilde{A}←widetilde{X} electronic transition is a bound-bound transition with enough structure to distinguish between different peroxy radicals as well as different conformers of the same peroxy radical. Two conformers of the nitrooxybutyl peroxy radical have been observed; the absorption features are red shifted from the same absorption features of sec-butyl peroxy radical. Calculations on the structure of nitrooxyalkyl peroxy radicals and general trends of the position of the widetilde{A}←widetilde{X} absorption transitions have also been performed and compared to those of unsubstituted peroxy radicals.

Transition State Geometry Measurements from 13C Isotope Effects. The Experimental Transition State for the Epoxidation of Alkenes with Oxaziridines

PubMed Central

Hirschi, Jennifer S.; Takeya, Tetsuya; Hang, Chao; Singleton, Daniel A.

2009-01-01

We suggest here and evaluate a methodology for the measurement of specific interatomic distances from a combination of theoretical calculations and experimentally measured 13C kinetic isotope effects. This process takes advantage of a broad diversity of transition structures available for the epoxidation of 2-methyl-2-butene with oxaziridines. From the isotope effects calculated for these transition structures, a theory-independent relationship between the C-O bond distances of the newly forming bonds and the isotope effects is established. Within the precision of the measurement, this relationship in combination with the experimental isotope effects provides a highly accurate picture of the C-O bonds forming at the transition state. The diversity of transition structures also allows an evaluation of the Schramm process for defining transition state geometries based on calculations at non-stationary points, and the methodology is found to be reasonably accurate. PMID:19146405

Simultaneous biosynthesis of putrebactin, avaroferrin and bisucaberin by Shewanella putrefaciens and characterisation of complexes with iron(III), molybdenum(VI) or chromium(V).

PubMed

Soe, Cho Zin; Telfer, Thomas J; Levina, Aviva; Lay, Peter A; Codd, Rachel

2016-09-01

Cultures of Shewanella putrefaciens grown in medium containing 10mM 1,4-diamino-2-butanone (DBO) as an inhibitor of ornithine decarboxylase and 10mM 1,5-diaminopentane (cadaverine) showed the simultaneous biosynthesis of the macrocyclic dihydroxamic acids: putrebactin (pbH 2 ), avaroferrin (avH 2 ) and bisucaberin (bsH 2 ). The level of DBO did not completely repress the production of endogenous 1,4-diaminobutane (putrescine) as the native diamine substrate of pbH 2 . The relative concentration of pbH 2 :avH 2 :bsH 2 was 1:2:1, which correlated with the substrate selection of putrescine:cadaverine in a ratio of 1:1. The macrocycles were characterised using LC-MS as free ligands and as 1:1 complexes with Fe(III) of the form [Fe(pb)] + , [Fe(av)] + or [Fe(bs)] + , with labile ancillary ligands in six-coordinate complexes displaced during ESI-MS acquisition; or with Mo(VI) of the form [Mo(O) 2 (pb)], [Mo(O) 2 (av)] or [Mo(O) 2 (bs)]. Chromium(V) complexes of the form [CrO(pb)] + were detected from solutions of Cr(VI) and pbH 2 in DMF using X-band EPR spectroscopy. Supplementation of S. putrefaciens medium with DBO and 1,3-diaminopropane, 1,6-diaminohexane or 1,4-diamino-2(Z)-butene (Z-DBE) resulted only in the biosynthesis of pbH 2 . The work has identified a native system for the simultaneous biosynthesis of a suite of three macrocyclic dihydroxamic acid siderophores and highlights both the utility of precursor-directed biosynthesis for expanding the structural diversity of siderophores, and the breadth of their coordination chemistry. Copyright © 2015 Elsevier Inc. All rights reserved.

The thermochemistry of cubane 50 years after its synthesis: a high-level theoretical study of cubane and its derivatives.

PubMed

Agapito, Filipe; Santos, Rui C; Borges dos Santos, Rui M; Martinho Simões, José A

2015-03-26

The gas-phase enthalpy of formation of cubane (603.4 ± 4 kJ mol(-1)) was calculated using an explicitly correlated composite method (W1-F12). The result obtained for cubane, together with the experimental value for the enthalpy of sublimation, 54.8 ± 2.0 kJ mol(-1), led to 548.6 ± 4.5 kJ mol(-1) for the solid-phase enthalpy of formation. This value is only 6.8 kJ mol(-1) higher than the 50-year-old original calorimetric result. The carbon-hydrogen bond dissociation enthalpy (C-H BDE) of cubane (438.4 ± 4 kJ mol(-1)), together with properties relevant for its experimental determination using gas-phase ion thermochemistry, namely the cubane gas-phase acidity (1704.6 ± 4 kJ mol(-1)), cubyl radical electron affinity (45.8 ± 4 kJ mol(-1)), cubane ionization energy (1435.1 ± 4 kJ mol(-1)), cubyl radical cation proton affinity (918.8 ± 4 kJ mol(-1)), cubane cation appearance energy (1099.6 ± 4 kJ mol(-1)), and cubyl ionization energy (661.2 ± 4 kJ mol(-1)), were also determined. These values were compared with those calculated for unstrained hydrocarbons (viz., methane, ethane, and isobutane). The strain energy of cubane (667.2 kJ mol(-1)) and cubyl radical (689.4 kJ mol(-1)) were independently estimated via quasihomodesmotic reactions. These values were related via a simple model to the C-H BDE in cubane. Taking into account the accuracy of the computational method, the comparison with high-precision experimental results, and the data consistency afforded by the relevant thermodynamic cycles, we claim an uncertainty better than ±4 kJ mol(-1) for the new enthalpy of formation values presented.

Dissociative Ionization and Thermal Decomposition of Cyclopentanone

PubMed Central

Pastoors, Johan I. M.; Bodi, Andras; Hemberger, Patrick

2017-01-01

Abstract Despite the growing use of renewable and sustainable biofuels in transportation, their combustion chemistry is poorly understood, limiting our efforts to reduce harmful emissions. Here we report on the (dissociative) ionization and the thermal decomposition mechanism of cyclopentanone, studied using imaging photoelectron photoion coincidence spectroscopy. The fragmentation of the ions is dominated by loss of CO, C2H4, and C2H5, leading to daughter ions at m/z 56 and 55. Exploring the C5H8O. + potential energy surface reveals hydrogen tunneling to play an important role in low‐energy decarbonylation and probably also in the ethene‐loss processes, yielding 1‐butene and methylketene cations, respectively. At higher energies, pathways without a reverse barrier open up to oxopropenyl and cyclopropanone cations by ethyl‐radical loss and a second ethene‐loss channel, respectively. A statistical Rice–Ramsperger–Kassel–Marcus model is employed to test the viability of this mechanism. The pyrolysis of cyclopentanone is studied at temperatures ranging from about 800 to 1100 K. Closed‐shell pyrolysis products, namely 1,3‐butadiene, ketene, propyne, allene, and ethene, are identified based on their photoion mass‐selected threshold photoelectron spectrum. Furthermore, reactive radical species such as allyl, propargyl, and methyl are found. A reaction mechanism is derived incorporating both stable and reactive species, which were not predicted in prior computational studies. PMID:28692134

Diuresis and reduced urinary osmolality in rats produced by small-molecule UT-A-selective urea transport inhibitors.

PubMed

Esteva-Font, Cristina; Cil, Onur; Phuan, Puay-Wah; Su, Tao; Lee, Sujin; Anderson, Marc O; Verkman, A S

2014-09-01

Urea transport (UT) proteins of the UT-A class are expressed in epithelial cells in kidney tubules, where they are required for the formation of a concentrated urine by countercurrent multiplication. Here, using a recently developed high-throughput assay to identify UT-A inhibitors, a screen of 50,000 synthetic small molecules identified UT-A inhibitors of aryl-thiazole, γ-sultambenzosulfonamide, aminocarbonitrile butene, and 4-isoxazolamide chemical classes. Structure-activity analysis identified compounds that inhibited UT-A selectively by a noncompetitive mechanism with IC50 down to ∼1 μM. Molecular modeling identified putative inhibitor binding sites on rat UT-A. To test compound efficacy in rats, formulations and administration procedures were established to give therapeutic inhibitor concentrations in blood and urine. We found that intravenous administration of an indole thiazole or a γ-sultambenzosulfonamide at 20 mg/kg increased urine output by 3-5-fold and reduced urine osmolality by ∼2-fold compared to vehicle control rats, even under conditions of maximum antidiuresis produced by 1-deamino-8-D-arginine vasopressin (DDAVP). The diuresis was reversible and showed urea > salt excretion. The results provide proof of concept for the diuretic action of UT-A-selective inhibitors. UT-A inhibitors are first in their class salt-sparing diuretics with potential clinical indications in volume-overload edemas and high-vasopressin-associated hyponatremias. © FASEB.

Emission characteristics of volatile organic compounds from coal-, coal gangue-, and biomass-fired power plants in China

NASA Astrophysics Data System (ADS)

Yan, Yulong; Yang, Chao; Peng, Lin; Li, Rumei; Bai, Huiling

2016-10-01

Face the large electricity demand, thermal power generation still derives the main way of electricity supply in China, account for 78.19% of total electricity production in 2013. Three types of thermal power plants, including coal-fired power plant, coal gangue-fired power plant and biomass-fired power plant, were chosen to survey the source profile, chemical reactivity and emission factor of VOCs during the thermal power generation. The most abundant compounds generated during coal- and coal gangue-fired power generation were 1-Butene, Styrene, n-Hexane and Ethylene, while biomass-fired power generation were Propene, 1-Butenen, Ethyne and Ethylene. The ratios of B/T during thermal power generation in this study was 0.8-2.6, which could be consider as the characteristics of coal and biomass burning. The field tested VOCs emission factor from coal-, coal gangue- and biomass-fired power plant was determined to be 0.88, 0.38 and 3.49 g/GJ, or showed as 0.023, 0.005 and 0.057 g/kg, with the amount of VOCs emission was 44.07, 0.08, 0.45 Gg in 2013, respectively. The statistical results of previous emission inventory, which calculated the VOCs emission used previous emission factor, may overestimate the emission amount of VOCs from thermal power generation in China.

From Sugars to Wheels: The Conversion of Ethanol to 1,3-Butadiene over Metal-Promoted Magnesia-Silicate Catalysts.

PubMed

Shylesh, Sankaranarayanapillai; Gokhale, Amit A; Scown, Corinne D; Kim, Daeyoup; Ho, Christopher R; Bell, Alexis T

2016-06-22

1,3-Butadiene (1,3-BD) is a high-value chemical intermediate used mainly as a monomer for the production of synthetic rubbers. The ability to source 1,3-BD from biomass is of considerable current interest because it offers the potential to reduce the life-cycle greenhouse gas (GHG) impact associated with 1,3-BD production from petroleum-derived naphtha. Herein, we report the development and investigation of a new catalyst and process for the one-step conversion of ethanol to 1,3-BD. The catalyst is prepared by the incipient impregnation of magnesium oxide onto a silica support followed by the deposition of Au nanoparticles by deposition-precipitation. The resulting Au/MgO-SiO2 catalyst exhibits a high activity and selectivity to 1,3-BD and low selectivities to diethyl ether, ethylene, and butenes. Detailed characterization of the catalyst shows that the desirable activity and selectivity of Au/MgO-SiO2 are a consequence of a critical balance between the acidic-basic sites associated with a magnesium silicate hydrate phase and the redox properties of the Au nanoparticles. A process for the conversion of ethanol to 1,3-BD, which uses our catalyst, is proposed and analyzed to determine the life-cycle GHG impact of the production of this product from biomass-derived ethanol. We show that 1,3-BD produced by our process can reduce GHG emissions by as much as 155 % relative to the conventional petroleum-based production of 1,3-BD. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A dynamic dilution system-based evaluation of the procedure adopted for determining ozone precursor volatile compounds.

PubMed

Palluau, Fabienne; Mirabel, Philippe; Millet, Maurice

2005-02-01

A dynamic dilution system was created to evaluate the performance and the reliability of ozone precursor volatile organic compound (VOC) sampling ("TO-Can" canisters) and analysis (thermal desorption/gas chromatography/flame ionisation detection) techniques used by the "Laboratoire Interregional de Chimie du Grand Est (LIC)". Different atmospheres of VOCs were generated at concentrations between 0.8 and 25 ppb, with temperatures of 0, 10, 20 and 30 degrees C, and with relative humidities of 0, 30, 50, 70 and 90%. These conditions are generally representative of those commonly observed in ambient air in the eastern France. This dynamic dilution allows the simulation of a wide range of scenarios (concentrations, temperatures and relative humidities). After assessing the capacity and performance of the system, it was applied in order to evaluate the recoveries and stabilities of VOCs from canisters used for the collection and analysis of two mixtures of VOCs. The first mixture contained six alkanes (ethane, propane, butane, pentane, hexane and heptane), and the second contained five alkenes (ethene, propene, butene, 1-pentene and 1-hexene), five aromatics (benzene, toluene, ethylbenzene, m-xylene and o-xylene), acetylene, and 1,3-butadiene. No significant losses of alkanes from the canisters were observed after 21 days of storage, and good recoveries of alkanes from the canisters (>80%) were obtained regardless of the concentration, the temperature and the relative humidity. However, losses of certain aromatics were noted at low relative humidity.

On the radiolysis of ethylene ices by energetic electrons and implications to the extraterrestrial hydrocarbon chemistry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Li; Maity, Surajit; Abplanalp, Matt

2014-07-20

The chemical processing of ethylene ices (C{sub 2}H{sub 4}) by energetic electrons was investigated at 11 K to simulate the energy transfer processes and synthesis of new molecules induced by secondary electrons generated in the track of galactic cosmic ray particles. A combination of Fourier transform infrared spectrometry (solid state) and quadrupole mass spectrometry (gas phase) resulted in the identification of six hydrocarbon molecules: methane (CH{sub 4}), the C2 species acetylene (C{sub 2}H{sub 2}), ethane (C{sub 2}H{sub 6}), the ethyl radical (C{sub 2}H{sub 5}), and—for the very first time in ethylene irradiation experiments—the C4 hydrocarbons 1-butene (C{sub 4}H{sub 8}) andmore » n-butane (C{sub 4}H{sub 10}). By tracing the temporal evolution of the newly formed molecules spectroscopically online and in situ, we were also able to fit the kinetic profiles with a system of coupled differential equations, eventually providing mechanistic information, reaction pathways, and rate constants on the radiolysis of ethylene ices and the inherent formation of smaller (C1) and more complex (C2, C4) hydrocarbons involving carbon-hydrogen bond ruptures, atomic hydrogen addition processes, and radical-radical recombination pathways. We also discuss the implications of these results on the hydrocarbon chemistry on Titan's surface and on ice-coated, methane-bearing interstellar grains as present in cold molecular clouds such as TMC-1.« less

Selective hydrogenation of 2-methyl-3-butyn-2-ol catalyzed by embedded polymer-protected PdZn nanoparticles

NASA Astrophysics Data System (ADS)

Okhlopkova, Lyudmila B.; Matus, Ekaterina V.; Prosvirin, Igor P.; Kerzhentsev, Michail A.; Ismagilov, Zinfer R.

2015-12-01

PdZn/TiO2 catalysts were synthesized by sol-gel method using a template Pluronic F127. PdZn nanoparticles with the size ranging from 1.7 to 2 nm were prepared by ethylene glycol reduction of ZnCl2 and Pd(CH3COO)2 in the presence of stabilizer and introduced into the matrix by addition into TiO2 sol, followed by different activation procedures. The structure, particles size, and chemical composition of nanoparticles and catalysts were characterized by transmission electron microscopy, X-ray photoelectron spectroscopy, X-ray fluorescence spectroscopy, and energy dispersive spectroscopy. The prepared catalysts have been tested in the selective hydrogenation of 2-methyl-3-butyn-2-ol, and the results have been compared with catalysts prepared by conventional impregnation. The results indicate that bimetallic PdZn nanoparticles-based catalysts show higher selectivity than corresponding monometallic Pd/TiO2. Embedded on titania, bimetallic nanoparticles stabilized with polyvinylpyrrolidone exhibit good activity (1.1-1.8 mol MBY/mol Pd/s-1) and high selectivity to 2-methyl-3-buten-2-ol (81.5-88.9 % at 95 % conversion). The influence of the nature of the stabilizer, the stabilizer/metal molar ratio, and activation conditions on the catalytic behavior of the samples was analyzed. It is shown that the particle size does not significantly affect the catalytic properties in the range of 4.4-6.5 nm. The nature and amount of stabilizer seem to be crucial to prepare efficient catalyst.

Synthesis and structure of an extended cluster lead(II) carboxylate, [Pb((CO){sub 9}Co{sub 3}({mu}{sub 3}-CCO{sub 2})){sub 2}]{sub n}. Role of core metals in cluster-derived hydrogenation catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xinjian Lei; Maoyu Shang; Fehlner, T.P.

The reaction of lead acetate with (CO){sub 9}Co{sub 3}({mu}{sub 3}-CCOOH) leads to the formation of [Pb((CO){sub 9}Co{sub 3}({mu}{sub 3}-CCO{sub 2})){sub 2}]{sub n}, I, in high yield. The structure of I exhibits unusual six-coordinate Pb(II) centers with two asymmetrical chelating cluster carboxylates (C{sub 22}Co{sub 6}PbO{sub 22}; triclinic P1; a = 8.119(1), b = 14.346(2), c = 14.660(2) {Angstrom}; {alpha} = 102.18(1), {beta} = 99.01(1), {gamma} = 97.30(1){degrees}; Z = 2). One oxygen of each cluster carboxylate ligand bridges between adjacent lead atoms such that a chainlike extended structure is found in the solid state without the presence of solvent or water.more » I is converted stepwide on pyrolysis into two metastable forms of solid materials (designated LT and HT), each of which has been characterized spectroscopically. The hydrogenation of 2-butenal as a test reaction shows that the LT catalyst exhibits selectivities similar to previous LT materials derived from other cobalt cluster metal carboxylates and that the HT material is totally inactive. The observed release of the lead core metal under HT activation conditions totally inactivates the catalyst and demonstrates exposure of the core metal in the HT form of these novel catalysts.« less

Comparative techno-economic analysis and process design for indirect liquefaction pathways to distillate-range fuels via biomass-derived oxygenated intermediates upgrading

DOE PAGES

Tan, Eric C. D.; Snowden-Swan, Lesley J.; Talmadge, Michael; ...

2016-09-27

This paper presents a comparative techno-economic analysis (TEA) of five conversion pathways from biomass to gasoline-, jet-, and diesel-range hydrocarbons via indirect liquefaction with a specific focus on pathways utilizing oxygenated intermediates. The four emerging pathways of interest are compared with one conventional pathway (Fischer-Tropsch) for the production of the hydrocarbon blendstocks. The processing steps of the four emerging pathways include biomass-to-syngas via indirect gasification, syngas clean-up, conversion of syngas to alcohols/oxygenates followed by conversion of alcohols/oxygenates to hydrocarbon blendstocks via dehydration, oligomerization, and hydrogenation. Conversion of biomass-derived syngas to oxygenated intermediates occurs via three different pathways, producing: (i) mixedmore » alcohols over a MoS 2 catalyst, (ii) mixed oxygenates (a mixture of C 2+ oxygenated compounds, predominantly ethanol, acetic acid, acetaldehyde, ethyl acetate) using an Rh-based catalyst, and (iii) ethanol from syngas fermentation. This is followed by the conversion of oxygenates/alcohols to fuel-range olefins in two approaches: (i) mixed alcohols/ethanol to 1-butanol rich mixture via Guerbet reaction, followed by alcohol dehydration, oligomerization, and hydrogenation, and (ii) mixed oxygenates/ethanol to isobutene rich mixture and followed by oligomerization and hydrogenation. The design features a processing capacity of 2000 tonnes/day (2205 short tons) of dry biomass. The minimum fuel selling prices (MFSPs) for the four developing pathways range from 3.40 dollars to 5.04 dollars per gasoline-gallon equivalent (GGE), in 2011 US dollars. Sensitivity studies show that MFSPs can be improved with co-product credits and are comparable to the commercial Fischer-Tropsch benchmark ($3.58/GGE). Altogether, this comparative TEA study documents potential economics for the developmental biofuel pathways via mixed oxygenates.« less

Comparative techno-economic analysis and process design for indirect liquefaction pathways to distillate-range fuels via biomass-derived oxygenated intermediates upgrading

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, Eric C. D.; Snowden-Swan, Lesley J.; Talmadge, Michael

This paper presents a comparative techno-economic analysis (TEA) of five conversion pathways from biomass to gasoline-, jet-, and diesel-range hydrocarbons via indirect liquefaction with a specific focus on pathways utilizing oxygenated intermediates. The four emerging pathways of interest are compared with one conventional pathway (Fischer-Tropsch) for the production of the hydrocarbon blendstocks. The processing steps of the four emerging pathways include biomass-to-syngas via indirect gasification, syngas clean-up, conversion of syngas to alcohols/oxygenates followed by conversion of alcohols/oxygenates to hydrocarbon blendstocks via dehydration, oligomerization, and hydrogenation. Conversion of biomass-derived syngas to oxygenated intermediates occurs via three different pathways, producing: (i) mixedmore » alcohols over a MoS 2 catalyst, (ii) mixed oxygenates (a mixture of C 2+ oxygenated compounds, predominantly ethanol, acetic acid, acetaldehyde, ethyl acetate) using an Rh-based catalyst, and (iii) ethanol from syngas fermentation. This is followed by the conversion of oxygenates/alcohols to fuel-range olefins in two approaches: (i) mixed alcohols/ethanol to 1-butanol rich mixture via Guerbet reaction, followed by alcohol dehydration, oligomerization, and hydrogenation, and (ii) mixed oxygenates/ethanol to isobutene rich mixture and followed by oligomerization and hydrogenation. The design features a processing capacity of 2000 tonnes/day (2205 short tons) of dry biomass. The minimum fuel selling prices (MFSPs) for the four developing pathways range from 3.40 dollars to 5.04 dollars per gasoline-gallon equivalent (GGE), in 2011 US dollars. Sensitivity studies show that MFSPs can be improved with co-product credits and are comparable to the commercial Fischer-Tropsch benchmark ($3.58/GGE). Altogether, this comparative TEA study documents potential economics for the developmental biofuel pathways via mixed oxygenates.« less

SmoXYB1C1Z of Mycobacterium sp. Strain NBB4: a Soluble Methane Monooxygenase (sMMO)-Like Enzyme, Active on C2 to C4 Alkanes and Alkenes

PubMed Central

Martin, Kiri E.; Ozsvar, Jazmin

2014-01-01

Monooxygenase (MO) enzymes initiate the aerobic oxidation of alkanes and alkenes in bacteria. A cluster of MO genes (smoXYB1C1Z) of thus-far-unknown function was found previously in the genomes of two Mycobacterium strains (NBB3 and NBB4) which grow on hydrocarbons. The predicted Smo enzymes have only moderate amino acid identity (30 to 60%) to their closest homologs, the soluble methane and butane MOs (sMMO and sBMO), and the smo gene cluster has a different organization from those of sMMO and sBMO. The smoXYB1C1Z genes of NBB4 were cloned into pMycoFos to make pSmo, which was transformed into Mycobacterium smegmatis mc2-155. Cells of mc2-155(pSmo) metabolized C2 to C4 alkanes, alkenes, and chlorinated hydrocarbons. The activities of mc2-155(pSmo) cells were 0.94, 0.57, 0.12, and 0.04 nmol/min/mg of protein with ethene, ethane, propane, and butane as substrates, respectively. The mc2-155(pSmo) cells made epoxides from ethene, propene, and 1-butene, confirming that Smo was an oxygenase. Epoxides were not produced from larger alkenes (1-octene and styrene). Vinyl chloride and 1,2-dichloroethane were biodegraded by cells expressing Smo, with production of inorganic chloride. This study shows that Smo is a functional oxygenase which is active against small hydrocarbons. M. smegmatis mc2-155(pSmo) provides a new model for studying sMMO-like monooxygenases. PMID:25015887

Monoamine oxidase inhibitory activity of methoxy-substituted chalcones.

PubMed

Mathew, Bijo; Mathew, Githa Elizabeth; Ucar, Gulberk; Joy, Monu; Nafna, E K; Lohidakshan, Krishnakumar K; Suresh, Jerad

2017-11-01

The MAO-B inhibitory activity of chalcone (1, 3- diphenyl-2-propen-1-one) based compounds arise from its structural similarity with 1, 4-diphenyl-2-butene, a known MAO-B inhibitor. Based on our previous report, the methoxy-substituted with fluorine containing chalcones are promising reversible MAO-B inhibitors, while in the present study, a series of methoxylated chalcones (C1-C9) bearing substitution on the para position of ring B was synthesized and evaluated for their human monoamine oxidase inhibitory activity. With the exception of (2E)-1-(4-methoxyphenyl)-3-(4-nitrophenyl) prop-2-en-1-one (C7), which is a nonselective inhibitor, the chalcones exhibited competitive, selective, and reversible inhibition of hMAO-B. The most potent compound, (2E)-3-[4-(dimethylamino) phenyl]-1-(4-methoxyphenyl) prop-2-en-1-one (C5), showed the best inhibitory activity towards hMAO-B (IC 50 =0.29±0.011μM;K i =0.14±0.001μM). The reversibility of MAO-B inhibition by compound C5 was demonstrated by the recovery of enzyme activity after dialysis of mixtures containing enzyme and inhibitor. The reversiblity of C5 was 25.38±1.40 and 92.00±3.87% before and after dialysis, respectively. PAMPA was carried out to evaluate the blood-brain barrier effects of the designated compounds. Moreover, the most potent MAO-B inhibitor, C5, was found to be nontoxic towards cultured hepatic cells at 5 and 25μM, with 97 and 90% viability. Molecular docking study was performed against hMAO-B to observe the binding site interactions of the lead compound. Copyright © 2017 Elsevier B.V. All rights reserved.

Emission characteristics of VOCs emitted from consumer and commercial products and their ozone formation potential.

PubMed

Dinh, Trieu-Vuong; Kim, Su-Yeon; Son, Youn-Suk; Choi, In-Young; Park, Seong-Ryong; Sunwoo, Young; Kim, Jo-Chun

2015-06-01

The characteristics of volatile organic compounds (VOCs) emitted from several consumer and commercial products (body wash, dishwashing detergent, air freshener, windshield washer fluid, lubricant, hair spray, and insecticide) were studied and compared. The spray products were found to emit the highest amount of VOCs (~96 wt%). In contrast, the body wash products showed the lowest VOC contents (~1.6 wt%). In the spray products, 21.6-96.4 % of the VOCs were propane, iso-butane, and n-butane, which are the components of liquefied petroleum gas. Monoterpene (C10H16) was the dominant component of the VOCs in the non-spray products (e.g., body wash, 53-88 %). In particular, methanol was present with the highest amount of VOCs in windshield washer fluid products. In terms of the number of carbon, the windshield washer fluids, lubricants, insecticides, and hair sprays comprised >95 % of the VOCs in the range C2-C5. The VOCs in the range C6-C10 were predominantly found in the body wash products. The dishwashing detergents and air fresheners contained diverse VOCs from C2 to C11. Besides comprising hazardous VOCs, VOCs from consumer products were also ozone precursors. The ozone formation potential of the consumer and commercial spray products was estimated to be higher than those of liquid and gel materials. In particular, the hair sprays showed the highest ozone formation potential.

Controlling hydrogenation activity and selectivity of bimetallic surfaces and catalysts

NASA Astrophysics Data System (ADS)

Murillo, Luis E.

Studies of bimetallic systems are of great interest in catalysis due to the novel properties that they often show in comparison with the parent metals. The goals of this dissertation are: (1) to expand the studies of self-hydrogenation and hydrogenation reactions on bimetallic surfaces under ultra high vacuum conditions (UHV) using different hydrocarbon as probe molecules; (2) to attempt to correlate the surface science findings with supported catalyst studies under more realistic conditions; and (3) to investigate the competitive hydrogenation of C=C versus C=O bonds on Pt(111) modified by different 3d transition metals. Hydrogenation studies using temperature programmed desorption (TPD) on Ni/Pt(111) bimetallic surfaces have demonstrated an enhancement in the low temperature hydrogenation activity relative to that of clean Pt(111). This novel hydrogenation pathway can be achieved under UHV conditions by controlling the structures of the bimetallic surfaces. A low temperature hydrogenation activity of 1-hexene and 1-butene has been observed on a Pt-Ni-Pt(111) subsurface structure, where Ni atoms are mainly present on the second layer of the Pt(111) single crystal. These results are in agreement with previous studies of self-hydrogenation and hydrogenation of cyclohexene. However, a much higher dehydrogenation activity is observed in the reaction of cyclohexene to produce benzene, demonstrating that the hydrocarbon structure has an effect on the reaction pathways. On the other hand, self-hydrogenation of 1-butene is not observed on the Pt-Ni-Pt(111) surface, indicating that the chain length (or molecular weight) has a significant effect on the selfhydrogenation activity. The gas phase reaction of cyclohexene on Ni/Pt supported on alumina catalysts has also shown a higher self-hydrogenation activity in comparison with the same reaction performed on supported monometallic catalysts. The effects of metal loading and impregnation sequence of the metal precursors are also discussed. Chemisorption, TPD, FTIR using a batch reactor for the self-hydrogenation of cyclohexene and CO adsorbed on the bimetallic surfaces were carried out to correlate surface science findings with experiments on supported bimetallic catalysts. To expand the studies on the effect of bimetallic structures on hydrogenation reactions, molecules with multiple functional groups such as alpha,beta-unsaturated aldehydes were also investigated. Studies of selective hydrogenation of a,ss-unsaturated aldehydes toward the desired unsaturated alcohols are of interest for the production of fine chemicals and pharmaceuticals. In these compounds, competitive hydrogenation of the C=C and C=O bonds occurs. TPD and HREELS experiments of acrolein (CH2=CH-CH=O) on Pt-based bimetallic surfaces are performed to investigate their effects on the hydrogenation activity of the C-O bond. The production of the desired unsaturated alcohol, allyl alcohol, has been observed for the first time on Pt-Ni-Pt(111) under UHV conditions. However, the propionaldehyde yield is five times higher than the allyl alcohol yield. Thus, a preferential isomerization reaction of allyl alcohol to propionaldehyde is very likely to occur on the Pt-Ni-Pt(111) surface as observed on the desorption studies of allyl alcohol on this surface. The hydrogenation of acrolein is also carried out under UHV conditions on other 3d-transition metal/Pt(111) surfaces such as Co/Pt(111), Fe/Pt(111), and Cu/Pt(111). So far, the highest activity and allyl alcohol yield are found on the Pt-Ni-Pt(111) surface with pre-adsorbed hydrogen.

High throughput HPLC-ESI(-)-MS/MS methodology for mercapturic acid metabolites of 1,3-butadiene: Biomarkers of exposure and bioactivation.

PubMed

Kotapati, Srikanth; Esades, Amanda; Matter, Brock; Le, Chap; Tretyakova, Natalia

2015-11-05

1,3-Butadiene (BD) is an important industrial and environmental carcinogen present in cigarette smoke, automobile exhaust, and urban air. The major urinary metabolites of BD in humans are 2-(N-acetyl-L-cystein-S-yl)-1-hydroxybut-3-ene/1-(N-acetyl-L-cystein-S-yl)-2-hydroxybut-3-ene (MHBMA), 4-(N-acetyl-L-cystein-S-yl)-1,2-dihydroxybutane (DHBMA), and 4-(N-acetyl-L-cystein-S-yl)-1,2,3-trihydroxybutyl mercapturic acid (THBMA), which are formed from the electrophilic metabolites of BD, 3,4-epoxy-1-butene (EB), hydroxymethyl vinyl ketone (HMVK), and 3,4-epoxy-1,2-diol (EBD), respectively. In the present work, a sensitive high-throughput HPLC-ESI(-)-MS/MS method was developed for simultaneous quantification of MHBMA and DHBMA in small volumes of human urine (200 μl). The method employs a 96 well Oasis HLB SPE enrichment step, followed by isotope dilution HPLC-ESI(-)-MS/MS analysis on a triple quadrupole mass spectrometer. The validated method was used to quantify MHBMA and DHBMA in urine of workers from a BD monomer and styrene-butadiene rubber production facility (40 controls and 32 occupationally exposed to BD). Urinary THBMA concentrations were also determined in the same samples. The concentrations of all three BD-mercapturic acids and the metabolic ratio (MHBMA/(MHBMA+DHBMA+THBMA)) were significantly higher in the occupationally exposed group as compared to controls and correlated with BD exposure, with each other, and with BD-hemoglobin biomarkers. This improved high throughput methodology for MHBMA and DHBMA will be useful for future epidemiological studies in smokers and occupationally exposed workers. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

ANALYSIS OF VAPORS FROM METHYLENE CHLORIDE EXTRACTS OF NUCLEAR GRADE HEPA FILTER FIBERGLASS SAMPLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

FRYE JM; ANASTOS HL; GUTIERREZ FC

2012-06-07

While several organic compounds were detected in the vapor samples used in the reenactment of the preparation of mounts from the extracts of nuclear grade high-efficiency particulate air filter fiberglass samples, the most significant species present in the samples were methylene chloride, phenol, phenol-d6, and 2-fluorophenol. These species were all known to be present in the extracts, but were expected to have evaporated during the preparation of the mounts, as the mounts appeared to be dry before any vapor was collected. These species were present at the following percentages of their respective occupational exposure limits: methylene chloride, 2%; phenol, 0.4%;more » and phenol-d6, 0.6%. However, there is no established limit for 2-fluorophenol. Several other compounds were detected at low levels for which, as in the case of 2-fluorophenol, there are no established permissible exposure limits. These compounds include 2-chlorophenol; N-nitroso-1-propanamine; 2-fluoro-1,1{prime}-biphenyl; 1,2-dihydroacenaphthylene; 2,5-cyclohexadiene-1,4-dione,2,6-bis(1,1-dimethylethyl); trimethyl oxirane; n-propylpropanamine; 2-(Propylamino)ethanol; 4-methoxy-1-butene; 6-methyl-5-hepten-2-one; and 3,4-dimethylpyridine. Some of these were among those added as surrogates or spike standards as part ofthe Advanced Technologies and Laboratories International, Inc. preparation ofthe extract of the HEPA filter media and are indicated as such in the data tables in Section 2, Results; other compounds found were not previously known to be present. The main inorganic species detected (sulfate, sodium, and sulfur) are also consistent with species added in the preparation of the methylene chloride extract of the high-efficiency particulate air sample.« less

Polyamines are traps for reactive intermediates in furan metabolism

PubMed Central

Peterson, Lisa A.; Phillips, Martin B.; Lu, Ding; Sullivan, Mathilde M.

2011-01-01

Furan is toxic and carcinogenic in rodents. Because of the large potential for human exposure, furan is classified as a possible human carcinogen. The detailed mechanism by which furan causes toxicity and cancer is not yet known. Since furan toxicity requires cytochrome P450-catalyzed oxidation of furan, we have characterized the urinary and hepatocyte metabolites of furan to gain insight into the chemical nature of the reactive intermediate. Previous studies in hepatocytes indicated that furan is oxidized to the reactive α,β-unsaturated dialdehyde, cis-2-butene-1,4-dial (BDA), which reacts with glutathione (GSH) to form 2-(S-glutathionyl)-succinaldehyde (GSH-BDA). This intermediate forms pyrrole cross-links with cellular amines such as lysine and glutamine. In this report, we demonstrate that GSH-BDA also forms cross-links with ornithine, putrescine and spermidine when furan is incubated with rat hepatocytes. The relative levels of these metabolites are not completely explained by hepatocellular levels of the amines or by their reactivity with GSH-BDA. Mercapturic acid derivatives of the spermidine cross-links were detected in the urine of furan-treated rats, which indicates that this metabolic pathway occurs in vivo. Their detection in furan-treated hepatocytes and in urine from furan-treated rats indicates that polyamines may play an important role in the toxicity of furan PMID:21842885

Maternal-Neonatal Pheromone/Interomone Added to Cat Litter Improves Litter Box Use and Reduces Aggression in Pair-Housed Cats.

PubMed

McGlone, John J; Garcia, Arlene; Thompson, William G; Pirner, Glenna M

2018-03-27

Introducing a new cat into a household with one or more resident cats can be a significant source of stress for the cats involved. These studies sought to determine if rabbit maternal-neonatal pheromone (2-methyl-2-butenal [2M2B]) in litter impacted cat social behaviors and litter box use. Study 1 determined that cats preferred to eliminate in litter containing 2M2B; other semiochemicals tested did not change litter box use. Cats prone to aggression were identified in an intermediate pilot study, and eight pairs of these cats were selected for Study 2. In Study 2, cat pairs were provided litter containing either vehicle or 2M2B for 24 hours. Cats experiencing control litter displayed more aggression during the first 6 hours (p < .01) and spent more time using the litter box 12 hours and 18 hours after pairing compared with cats experiencing litter with 2M2B (p = .02). These results suggest 2M2B-infused cat litter may act as an interomone in cats housed domestically to prevent initial occurrences of aggression and may improve cat welfare in multicat households.

Total OH reactivity measurements in ambient air in a southern Rocky Mountain ponderosa pine forest during BEACHON-SRM08 summer campaign

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nakashima, Yoshihiro; Kato, Shungo; Greenberg, Jim

2014-03-01

Total OH reactivity was measured during the Bio-hydro-atmosphere interactions of Energy, Aerosols, Carbon, H2O, Organics and Nitrogen-Southern Rocky Mountain 2008 field campaign (BEACHON-SRM08) held at Manitou Experimental Forest (MEF) in Colorado USA during the summer season in August, 2008. The averaged total OH reactivity was 6.8 s-1, smaller than that measured in urban or suburban areas, while sporadically high OH reactivity was also observed during some evenings. The total OH reactivity measurements were accompanied by observations of traces species such as CO, NO, NOy, O3 and SO2 and VOCs. From the calculation of OH reactivity based on the analysis ofmore » these trace species, 35.3-46.3% of OH reactivity for VOCs came from biogenic species that are dominated by 2-methyl-3-butene-2-ol (MBO), and monoterpenes. MBO was the most prominent contribution to OH reactivity of any other trace species. A comparison of observed and calculated OH reactivity shows that the calculated OH reactivity is 29.5-34.8% less than the observed value, implying the existence of missing OH sink. One of the candidates of missing OH was thought to be the oxidation products of biogenic species.« less

Volatile metabolomic signature of human breast cancer cell lines

PubMed Central

Silva, Catarina L.; Perestrelo, Rosa; Silva, Pedro; Tomás, Helena; Câmara, José S.

2017-01-01

Breast cancer (BC) remains the most prevalent oncologic pathology in women, causing huge psychological, economic and social impacts on our society. Currently, the available diagnostic tools have limited sensitivity and specificity. Metabolome analysis has emerged as a powerful tool for obtaining information about the biological processes that occur in organisms, and is a useful platform for discovering new biomarkers or make disease diagnosis using different biofluids. Volatile organic compounds (VOCs) from the headspace of cultured BC cells and normal human mammary epithelial cells, were collected by headspace solid-phase microextraction (HS-SPME) and analyzed by gas chromatography combined with mass spectrometry (GC–MS), thus defining a volatile metabolomic signature. 2-Pentanone, 2-heptanone, 3-methyl-3-buten-1-ol, ethyl acetate, ethyl propanoate and 2-methyl butanoate were detected only in cultured BC cell lines. Multivariate statistical methods were used to verify the volatomic differences between BC cell lines and normal cells in order to find a set of specific VOCs that could be associated with BC, providing comprehensive insight into VOCs as potential cancer biomarkers. The establishment of the volatile fingerprint of BC cell lines presents a powerful approach to find endogenous VOCs that could be used to improve the BC diagnostic tools and explore the associated metabolomic pathways. PMID:28256598

Polyphenylenesulfide, noxon® an ozone scavenger for the analysis of oxygenated terpenes in air

NASA Astrophysics Data System (ADS)

Calogirou, A.; Duane, M.; Kotzias, D.; Lahaniati, M.; Larsen, B. R.

During sampling, oxygenated terpenes may undergo decomposition through reaction with atmospheric ozone. We have studied their ozonolytic decomposition during preconcentration on Tenax. The saturated. terpenoids 1,8-cineole, bornyl acetate nopinone and pinonaldehyde are practically unaffected by ozone in the range of 8 to 120 ppbv. Compounds which contain one or more C-C double bonds are decomposed in the order: linalool ≈ citronellal ≈ 6-methyl-5-hepten-2-one > citral > 4-acetyl-1-methyl-cyclohexane > 3-(1-methylethenyl)-6-oxo-heptanal > myrtenal ≈ 2-methyl-3-buten-2-ol. The degree of decomposition varies from 0 to 5% for the least reactive to 80 to 90% for the most reactive compounds. A broad range of material was investigated as potential ozone scavengers. By using the polymer noXon (polyphenylenesulfide) all the investigated compounds could be sampled with quantitative recoveries even at high ozone mixing ratios (95-110 ppbv). This ozone scrubber was tested for sampling of terpene oxidation products on Tenax and dinitrophenylhydrazine impregnated C 18-silicagel cartridges. Recoveries from 85 to 110% were obtained for all investigated compounds. The method was used for the analysis of oxidation products of terpenes in ambient air in three campaigns. Attention was focused on nopinone from β-pinene, pinonaldehyde from α-pinene, 3-(1-methylethenyl)-6-oxo-heptanal and 4-acetyl-1-methyl-cyclohexane from limonene, and 5-(1-methylethyl)-bicyclo[3.1.0] hexan-2-one from sabinene. Nopinone was the only product which could be frequently detected in ratios from 0 to 90% of the measured β-pinene concentrations. Pinonaldehyde was encountered only once (30% of α-pinene) while the other products were not found. These data have to be seen as a first attempt to measure terpene oxidation products in the troposphere.

Characterization of antiproliferative activity constituents from Artocarpus heterophyllus.

PubMed

Zheng, Zong-Ping; Xu, Yang; Qin, Chuan; Zhang, Shuang; Gu, Xiaohong; Lin, Yingying; Xie, Guobin; Wang, Mingfu; Chen, Jie

2014-06-18

Artocarpus heterophyllus is an evergreen fruit tree cultivated in many tropical regions. Previous studies have shown that some of its compositions exhibited potential tyrosinase inhibition activities. This study indentified 8 new phenolic compounds, artoheterophyllins E-J (1-6), 4-geranyl-2',3,4',5-tetrahydroxy-cis-stilbene (7), and 5-methoxymorican M (8) and 2 new natural compounds (9 and 10), 2,3-dihydro-5,7-dihydroxy-2-(2-hydroxy-4-methoxyphenyl)-4H-benzopyran-4-one and 6-[(1S,2S)-1,2-dihydroxy-3-methylbutyl]-2-(2,4-dihydroxyphenyl)-5-hydroxy-7-methoxy-3-(3-methyl-2-buten-1-yl)-4H-1-benzopyran-4-one, together with 23 known compounds (11-33), from the ethanol extract of the wood of A. heterophyllus. The structures of the eight new compounds (1-8) and two new natural compounds were established by extensive 1D- and 2D-NMR experiments. The anticancer effects of the isolated compounds were examined in MCF-7, H460, and SMMC-7721 human cancer cell lines by MTT assay. Compounds 5, 11, 12, and 30 significantly reduced the cell viabilities of these cell lines. Especially, compounds 11 and 30 resulted in more potent cytotoxicity than the positive control, 5-fluorouracil (5-Fu), in SMMC-7721 cell line, with IC50 values of 15.85 and 12.06 μM, whereas compound 30 exhibited more potent cytotoxicity than 5-Fu in NCI-H460 cell line, with an IC50 value of 5.19 μM. In addition, this study suggests that compounds 11 and 30 from the wood of A. heterophyllus have anticancer potential via MAPK pathways.

Kinetic and mechanistic aspects of propene oligomerization with ionic organozirconium and -hafnium compounds: Crystal structures of [Cp* {sub 2}MMe(THT)]{sup +}[BPh{sub 4}]{sup {minus}} (M=Zr, Hf)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eshuis, J.J.W.; Tan, Y.Y.; Meetsma, A.

1992-01-01

In N,N-dimethylaniline the ionic complexes [Cp{sup *}{sub 2}MMe(THT)]{sup +}[BPh{sub 4}]{sup {minus}}(M=Zr,Hf) oligomerize propene to low molecular weight oligomers. At room temperature for M = Zr a rather broad molecular weight distribution is obtained (C{sub 6} to C{sub 24}), whereas for M = Hf only one dimer (4-methyl-1-pentene) and one trimer (4,6-dimethyl-1-heptene) are formed. With an increase in temperature the product composition shifts to lower molecular weights, but the specific formation of head-to-tail oligomers is retained. The oligomers are formed by {beta}-Me transfer from the growing oligopropene alkyl chain to the metal center. The molecular weight distributions of the oligomers producedmore » at temperature between 5 and 45 {degrees}C are satisfactorily described by the Flory-Schulz theory. This allows the calculation of ratios of rate coefficients for propagation (k{sub p}) and termination (k{sub t}). Inactivation of the catalysts is caused by two different mechanisms. At room temperature allylic C-H activation of monomer and isobutene (formed by a minor {beta}-H transfer termination) gives inactive (meth) allyl compounds, [Cp{sup *} {sub 2}M({eta}{sup 3}-C{sub 3}H{sub 5})]{sup +} and [Cp{sup *}{sub 2}M({eta}{sup 3}-C{sub 4}H{sub 7})]{sup +} (M = Zr, Hf). At elevated temperatures (>45 {degrees}C) catalytically inactive zwitterionic complexes Cp{sup *}{sub M}{sup +}-m-C{sub 6}H{sub 4}-BPh{sub 3}{sup {minus}}(M = Zr, Hf) are formed through aromatic C-H activation. Reactivation of the inactive (meth)allyl complexes can be achieved by addition of hydrogen to the oligomerization mixtures. 38 refs., 4 figs., 7 tabs.« less

Aspergillus Volatiles Regulate Aflatoxin Synthesis and Asexual Sporulation in Aspergillus parasiticus▿

PubMed Central

Roze, Ludmila V.; Beaudry, Randolph M.; Arthur, Anna E.; Calvo, Ana M.; Linz, John E.

2007-01-01

Aspergillus parasiticus is one primary source of aflatoxin contamination in economically important crops. To prevent the potential health and economic impacts of aflatoxin contamination, our goal is to develop practical strategies to reduce aflatoxin synthesis on susceptible crops. One focus is to identify biological and environmental factors that regulate aflatoxin synthesis and to manipulate these factors to control aflatoxin biosynthesis in the field or during crop storage. In the current study, we analyzed the effects of aspergillus volatiles on growth, development, aflatoxin biosynthesis, and promoter activity in the filamentous fungus A. parasiticus. When colonies of Aspergillus nidulans and A. parasiticus were incubated in the same growth chamber, we observed a significant reduction in aflatoxin synthesis and asexual sporulation by A. parasiticus. Analysis of the headspace gases demonstrated that A. nidulans produced much larger quantities of 2-buten-1-ol (CA) and 2-ethyl-1-hexanol (EH) than A. parasiticus. In its pure form, EH inhibited growth and increased aflatoxin accumulation in A. parasiticus at all doses tested; EH also stimulated aflatoxin transcript accumulation. In contrast, CA exerted dose-dependent up-regulatory or down-regulatory effects on aflatoxin accumulation, conidiation, and aflatoxin transcript accumulation. Experiments with reporter strains carrying nor-1 promoter deletions and mutations suggested that the differential effects of CA were mediated through separate regulatory regions in the nor-1 promoter. The potential efficacy of CA as a tool for analysis of transcriptional regulation of aflatoxin biosynthesis is discussed. We also identify a novel, rapid, and reliable method to assess norsolorinic acid accumulation in solid culture using a Chroma Meter CR-300 apparatus. PMID:17890344

Investigations of electron attachment to the perfluorocarbon molecules c-C4F8, 2-C4F8, 1,3 C4F6, and c-C5F8

NASA Astrophysics Data System (ADS)

Feil, Stefan; Märk, Tilmann D.; Mauracher, Andreas; Scheier, Paul; Mayhew, Chris A.

2008-11-01

Non-dissociative and dissociative electron attachment to a series of gas-phase perfluorocarbons (PFCs), namely octafluorocyclobutane, c-C4F8, octafluorobut-2-ene (perfluoro-2-butene), 2-C4F8, hexafluorobuta-1,3-diene (1,3 perfluorobutadiene), 1,3 C4F6, and octafluorocyclopentene (perfluorocyclopentene), c-C5F8, of importance to technological plasmas, have been investigated using two different, but complimentary, instruments available in Innsbruck over the electron energy range 0-20 eV. Anion yields as a function of electron energy have been recorded, with the positions and intensities of the electron attachment resonances being determined. One of these instruments is a double focusing sector field mass spectrometer (VG-ZAB-2SEQ), which has been used for measurements requiring high sensitivity and for obtaining accurate relative anion yields. It has also been used to determine the electron detachment lifetimes of the parent anions under various accelerating voltages, and these results are also presented. The second instrument (CELIA) is a trochoidal electron monochromator coupled to a quadrupole mass filter with a pulse counting system for detecting product anionic species. This provides a much higher energy resolution than the VG-ZAB, which makes it a better instrument to investigate narrow energy resonances close to 0 eV. The results of anion yields, peak positions and the relative intensities presented in this paper are compared with previous data of electron attachment to the above PFCs, including investigations by Professor Eugen Illenberger.

Application of the Firefly and Luus-Jaakola algorithms in the calculation of a double reactive azeotrope

NASA Astrophysics Data System (ADS)

Mendes Platt, Gustavo; Pinheiro Domingos, Roberto; Oliveira de Andrade, Matheus

2014-01-01

The calculation of reactive azeotropes is an important task in the preliminary design and simulation of reactive distillation columns. Classically, homogeneous nonreactive azeotropes are vapor-liquid coexistence conditions where phase compositions are equal. For homogeneous reactive azeotropes, simultaneous phase and chemical equilibria occur concomitantly with equality of compositions (in the Ung-Doherty transformed space). The modeling of reactive azeotrope calculation is represented by a nonlinear algebraic system with phase equilibrium, chemical equilibrium and azeotropy equations. This nonlinear system can exhibit more than one solution, corresponding to a double reactive azeotrope. In a previous paper (Platt et al 2013 J. Phys.: Conf. Ser. 410 012020), we investigated some numerical aspects of the calculation of reactive azeotropes in the isobutene + methanol + methyl-tert-butyl-ether (with two reactive azeotropes) system using two metaheuristics: the Luus-Jaakola adaptive random search and the Firefly algorithm. Here, we use a hybrid structure (stochastic + deterministic) in order to produce accurate results for both azeotropes. After identifying the neighborhood of the reactive azeotrope, the nonlinear algebraic system is solved using Newton's method. The results indicate that using metaheuristics and some techniques devoted to the calculation of multiple minima allows both azeotropic coordinates in this reactive system to be obtains. In this sense, we provide a comprehensive analysis of a useful framework devoted to solving nonlinear systems, particularly in phase equilibrium problems.

Analysis of biogenic carbonyl compounds in rainwater by stir bar sorptive extraction technique with chemical derivatization and gas chromatography‐mass spectrometry

PubMed Central

Lewis, Alastair C.; Shaw, Marvin D.

2016-01-01

Stir bar sorptive extraction is a powerful technique for the extraction and analysis of organic compounds in aqueous matrices. Carbonyl compounds are ubiquitous components in rainwater, however, it is a major challenge to accurately identify and sensitively quantify carbonyls from rainwater due to the complex matrix. A stir bar sorptive extraction technique was developed to efficiently extract carbonyls from aqueous samples following chemical derivatization by O‐(2,3,4,5,6‐pentafluorobenzyl) hydroxylamine hydrochloride. Several commercial stir bars in two sizes were used to simultaneously measure 29 carbonyls in aqueous samples with detection by gas chromatography with mass spectrometry. A 100 mL aqueous sample was extracted by stir bars and the analytes on stir bars were desorbed into a 2 mL solvent solution in an ultrasonic bath. The preconcentration Coefficient for different carbonyls varied between 30 and 45 times. The limits of detection of stir bar sorptive extraction with gas chromatography mass spectrometry for carbonyls (10–30 ng/L) were improved by ten times compared with other methods such as gas chromatography with electron capture detection and stir bar sorptive extraction with high‐performance liquid chromatography and mass spectrometry. The technique was used to determine carbonyls in rainwater samples collected in York, UK, and 20 carbonyl species were quantified including glyoxal, methylglyoxal, isobutenal, 2‐hydroxy ethanal. PMID:27928898

Potato wound-healing tissues: A rich source of natural antioxidant molecules with potential for food preservation.

PubMed

Dastmalchi, Keyvan; Wang, Isabel; Stark, Ruth E

2016-11-01

The need for safe, effective preservatives is a prominent issue in the food and drug industries, reflecting demand for natural alternatives to synthetic chemicals viewed as harmful to consumers and the environment. Thus, this study determined the identities and scavenging capacities of antioxidant metabolites produced as a response to potato tuber wounding, using activity-guided fractionation of polar extracts from a Yukon Gold cultivar that had previously exhibited exceptionally high radical-scavenging activity. Activity-guided fractionation using the ABTS(+) radical scavenging assay and LC-MS with TOF-MS for compositional analysis of the most potent antioxidant fractions yielded identification of nine constituents: coumaroylputrescine; feruloylquinic acid; isoferuloylputrescine; ferulic acid; 22,25-dimethoxy-3-[[2,3,4-tri-O-methyl-6-O-(2,3,4,6-tetra-O-methyl-β-d-glucopyranosyl)-β-d-glucopyranosyl]oxy]-(3β)-lanost-9(11)-en-24-one; 4-(2Z)-2-decen-1-yl-5-[1-(4-hydroxyphenyl)decyl]-1,2-benzenediol; 8-[(2E)-3,7-dimethyl-2,6-octadien-1-yl]-5-hydroxy-2,8-dimethyl-6-(3-methyl-2-buten-1-yl)-2H-1-benzopyran-4,7(3H,8H)-dione; 3-[(2-O-β-d-glucopyranosyl-β-d-glucopyranosyl)oxy]-20-[(6-O-β-d-xylopyranosyl-β-d-glucopyranosyl)oxy]-dammar-24-en-19-al; (3β)-28-oxo-28-(phenylmethoxy)oleanan-3-yl 2-O-β-d-galactopyranosyl-3-O-(phenylmethyl)-, butyl ester β-d-glucopyranosiduronic acid. A positive correlation was observed between the scavenging activities and the polarities of the active fractions. The antioxidant capacities of the fractions were also characterised by monitoring the activity throughout a 45-minute assay period. Copyright © 2016 Elsevier Ltd. All rights reserved.

Potato Wound-Healing Tissues: A Rich Source of Natural Antioxidant Molecules with Potential for Food Preservation

PubMed Central

Dastmalchi, Keyvan; Wang, Isabel; Stark, Ruth E.

2016-01-01

The need for safe, effective preservatives is a prominent issue in the food and drug industries, reflecting demand for natural alternatives to synthetic chemicals viewed as harmful to consumers and the environment. Thus, this study determined the identities and scavenging capacities of antioxidant metabolites produced as a response to potato tuber wounding, using activity-guided fractionation of polar extracts from a Yukon Gold cultivar that had previously exhibited exceptionally high radical-scavenging activity. Activity-guided fractionation using the ABTS•+ radical scavenging assay and LC-MS with TOF-MS for compositional analysis of the most potent antioxidant fractions yielded identification of nine constituents: coumaroylputrescine; feruloylquinic acid; isoferuloylputrescine; ferulic acid; 22,25-dimethoxy-3-[[2,3,4-tri-O-methyl-6-O-(2,3,4,6-tetra-O-methyl-β-D-glucopyranosyl)-β-D-glucopyranosyl]oxy]-(3β)-lanost-9(11)-en-24-one; 4-(2Z)-2-decen-1-yl-5-[1-(4-hydroxyphenyl)decyl]-1,2-benzenediol; 8-[(2E)-3,7-dimethyl-2,6-octadien-1-yl]-5-hydroxy-2,8-dimethyl-6-(3-methyl-2-buten-1-yl)-2H-1-benzopyran-4,7(3H,8H)-dione; 3-[(2-O-β-D-glucopyranosyl-β-D-glucopyranosyl)oxy]-20-[(6-O-β-D-xylopyranosyl-β-D-glucopyranosyl)oxy]-dammar-24-en-19-al; (3β)-28-oxo-28-(phenylmethoxy)oleanan-3-yl 2-O-β-D-galactopyranosyl-3-O-(phenylmethyl)-, butyl ester β-D-glucopyranosiduronic acid. A positive correlation was observed between the scavenging activities and the polarities of the active fractions. The antioxidant capacities of the fractions were also characterised by monitoring the activity throughout a 45-minute assay period. PMID:27211673

Experimental investigation of an alternating evaporator duty refrigerator/freezer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lavanis, M.; Haider, I.; Radermacher, R.

1998-12-31

A bistable solenoid valve has been used to build an alternating evaporator duty (AED) domestic refrigerator/freezer. This refrigerator has two vapor compression refrigeration loops that share a common compressor, condenser, and suction line heat exchanger. Each of the refrigeration loops has an expansion device and evaporator. One evaporator is located in the fresh food compartment and the other is located in the freezer compartment. The bistable solenoid valve directs the flow of the refrigerant through one loop at a time. Only one of the two compartments is cooled at any given time. With this configuration, the food compartment is cooledmore » at a higher evaporator temperature than the freezer. Due to this, the energy efficiency of the refrigerator is improved by 8.5% over a conventional domestic refrigerator/freezer. Also, this cycle allows for completely independent temperature control of the freezer and fresh food compartments. There may be a penalty because this cycle does not allow for both loops to be simultaneously optimized. Isobutane was the only refrigerant used in this investigation.« less

Analysis of cocaine and three of its metabolites in hair by gas chromatography-mass spectrometry using ion-trap detection for CI/MS/MS.

PubMed

Cognard, Emmanuelle; Rudaz, Serge; Bouchonnet, Stéphane; Staub, Christian

2005-11-05

A sensitive GC/CI/MS/MS method was developed for the simultaneous determination of cocaine (COC), anhydroecgonine methylester (cocaine pyrolysis product, AEME), ecgonine methylester (cocaine enzymatic hydrolysis product, EME) and cocaethylene (cocaine with ethanol trans-esterification product, COET) in human hair samples. After acid hydrolysis, hair samples were extracted with an automated solid phase extraction (SPE). The analysis of cocaine and its three metabolites was performed using an ion-trap spectrometer in positive chemical ionization with isobutane as gas reagent. The procedure was validated. Weighted linear regression was found appropriate in a concentration range of 0.10-5.00 ng/mg for AEME, 0.05-5.00 ng/mg for COC, EME and COET. The limit of detection was estimated at 0.005 ng/mg for COC and COET, at 0.025 ng/mg for EME, and at 0.050 ng/mg for AEME. Method performance was evaluated in terms of trueness and precision using quality control (QC) samples over the investigated ranges. Method selectivity and robustness were also demonstrated.

Selective methylative homologation: an alternate route to alkane upgrading.

PubMed

Bercaw, John E; Hazari, Nilay; Labinger, Jay A; Scott, Valerie J; Sunley, Glenn J

2008-09-10

InI3 catalyzes the reaction of branched alkanes with methanol to produce heavier and more highly branched alkanes, which are more valuable fuels. The reaction of 2,3-dimethylbutane with methanol in the presence of InI3 at 180-200 degrees C affords the maximally branched C7 alkane, 2,2,3-trimethylbutane (triptane). With the addition of catalytic amounts of adamantane the selectivity of this transformation can be increased up to 60%. The lighter branched alkanes isobutane and isopentane also react with methanol to generate triptane, while 2-methylpentane is converted into 2,3-dimethylpentane and other more highly branched species. Observations implicate a chain mechanism in which InI3 activates branched alkanes to produce tertiary carbocations which are in equilibrium with olefins. The latter react with a methylating species generated from methanol and InI3 to give the next-higher carbocation, which accepts a hydride from the starting alkane to form the homologated alkane and regenerate the original carbocation. Adamantane functions as a hydride transfer agent and thus helps to minimize competing side reactions, such as isomerization and cracking, that are detrimental to selectivity.

Channel electron multipliers - Detection efficiencies with opaque MgF2 photocathodes at XUV wavelengths

NASA Technical Reports Server (NTRS)

Lapson, L. B.; Timothy, J. G.

1976-01-01

Detection efficiencies of channel electron multipliers (CEM) with opaque MgF2 photocathodes obtained in the extreme ultraviolet (XUV), 44 A to 990 A, are reported. A stable highly efficient response is reported for that interval, with no adverse effects on CEM performance. Efficiencies twice those of uncoated CEMs are obtained for 50 A to 350 A. The Mullard B419BL and Galileo 4510WL single-stage cone-cathode CEMs were used in the experiments. A rare-gas double ionization chamber was employed as absolute standard detector for 406 A to 990 A, and a flow Geiger counter filled with 96% argon and 4% isobutane for 44 A to 256 A. Absolute detection efficiencies are 10% higher from 67 A to 990 A when photocathodes are illuminated at an angle of incidence 45 deg. The photocathodes suffered no loss of response in storage (in vacuum or air) after an initial aging period. Effects of scattered UV radiation are greatly reduced when MgF2-coated CEMs are used in the XUV.

Comparison of Ion Chemistries in Octafluoro-2-butene (2-C4F8) and in Octfluorocyclobutane (c-C4F8)

NASA Astrophysics Data System (ADS)

Jiao, Charles; Dejoseph, Charles; Garscadden, Alan

2007-10-01

2-C4F8 is one of the promising candidates to replace c-C4F8 that has been widely used for dielectric etching but is not environmentally friendly. In this study we have investigated electron impact ionization and ion-molecule reactions of 2-C4F8 using Fourier transform mass spectrometry (FTMS), and compared the results with those of c-C4F8 we have studied previously. Electron impact ionization of 2-C4F8 produces 15 ionic species including C4F7,8^+, C3F3,5,6^+, C2F4^+ and CF1-3^+ as the major ions. The total ionization cross section of 2-C4F8 reaches a maximum of 1.8x10-15 cm^2 at 90 eV. The ionization is dominated by the channel forming the parent ion C4F8^+ from 12 to 18 eV, and by the channel forming C3F5^+ from 18 to 70 eV. After 70 eV, CF3^+ becomes the dominant product ion. Among the major ions generated from the electron impact ionization of 2-C4F8, only CF^+, CF2^+ and CF3^+ are found to react with 2-C4F8, via F^- abstraction or charge transfer mechanism. The charge transfer reaction of Ar^++2-C4F8 produces primarily C4F7^+.

Comparative Metabolism of Furan in Rodent and Human Cryopreserved Hepatocytes

PubMed Central

Gates, Leah A.; Phillips, Martin B.; Matter, Brock A.

2014-01-01

Furan is a liver toxicant and carcinogen in rodents. Although humans are most likely exposed to furan through a variety of sources, the effect of furan exposure on human health is still unknown. In rodents, furan requires metabolism to exert its toxic effects. The initial product of the cytochrome P450 2E1-catalyzed oxidation is a reactive α,β-unsaturated dialdehyde, cis-2-butene-1,4-dial (BDA). BDA is toxic and mutagenic and consequently is considered responsible for the toxic effects of furan. The urinary metabolites of furan in rats are derived from the reaction of BDA with cellular nucleophiles, and precursors to these metabolites are detected in furan-exposed hepatocytes. Many of these precursors are 2-(S-glutathionyl)butanedial-amine cross-links in which the amines are amino acids and polyamines. Because these metabolites are derived from the reaction of BDA with cellular nucleophiles, their levels are a measure of the internal dose of this reactive metabolite. To compare the ability of human hepatocytes to convert furan to the same metabolites as rodent hepatocytes, furan was incubated with cryopreserved human and rodent hepatocytes. A semiquantitative liquid chromatography with tandem mass spectrometry assay was developed for a number of the previously characterized furan metabolites. Qualitative and semiquantitative analysis of the metabolites demonstrated that furan is metabolized in a similar manner in all three species. These results indicate that humans may be susceptible to the toxic effects of furan. PMID:24751574

High-performance liquid chromatographic method for the simultaneous determination of 24 fragrance allergens to study scented products.

PubMed

Villa, C; Gambaro, R; Mariani, E; Dorato, S

2007-07-27

The European legislation on cosmetic products has recently required the declaration of 26 compounds (24 volatile chemicals and 2 natural extracts) on the label of final products when exceeding a stipulated cut-off level. In this work a rapid reliable and specific RP-HPLC method coupled with diode array detector (DAD) has been developed for the simultaneous determination and quantification of the 24 volatile chemicals: amyl cinnamal, benzyl alcohol, cinnamyl alcohol, citral, eugenol, hydroxy-citronellal, isoeugenol, amylcinnamyl alcohol, benzyl salicylate, cinnamal, coumarin, geraniol, Lyral (hydroxy-methylpentylcyclohexene carboxaldehyde), anisyl alcohol, benzyl cinnamate, farnesol, Lilial (2-(4-tert-butylbenzyl)propionaldehyde) linalool, benzyl benzoate, citronellol, hexyl cinnamal, limonene, methylheptin carbonate, alpha-isomethyl ionone (3-methyl-4-(2,6,6-trimethyl-2-cyclohexen-1-yl)-3-buten-2-one). The 24 analytes were appropriately separated over a running time of 40 min, on a C18 column using a simple gradient elution (acetonitrile/water) with flow rate from 0.7 to 1.0 ml/min and UV acquisition at 210, 254 and 280 nm. All calibration curves showed good linearity (r2>0.99) within test ranges. The method was successfully applied to the qualitative and quantitative determination of the potential allergens in four commercial scented products, with satisfactory accuracy and precision. The results indicated that this simple and efficient method can be used for quality assessment of complex matrices such us cosmetic scented products.

Quantitative analysis of trihydroxybutyl mercapturic acid, a urinary metabolite of 1, 3-butadiene, in humans

PubMed Central

Kotapati, Srikanth; Matter, Brock A.; Grant, Amy L.; Tretyakova, Natalia Y.

2011-01-01

1,3-butadiene (BD)* is a known human carcinogen present in cigarette smoke and in automobile exhaust, leading to widespread exposure of human populations. BD requires cytochrome P450-mediated metabolic activation to electrophilic species, e.g. 3,4-epoxy-1-butene (EB), hydroxymethylvinylketone (HMVK), and 3,4-epoxy-1,2-diol (EBD), which form covalent adducts with DNA. EB, HMVK, and EBD can be conjugated with glutathione and ultimately excreted in urine as monohydroxybutenyl mercapturic acid (MHBMA), dihydroxybutyl mercapturic acid (DHBMA), and trihydroxybutyl mercapturic acid (THBMA), respectively, which can serve as biomarkers of BD exposure and metabolic processing. While MHBMA and DHBMA have been found in smokers and non-smokers, THBMA has not been previously detected in humans. In the present work, an isotope dilution HPLC-ESI−-MS/MS methodology was developed and employed to quantify THBMA in urine of known smokers and non-smokers (19–27 per group). The new method has excellent sensitivity (LOQ, 1 ng/mL urine) and achieves accurate quantitation using a small sample volume (100 µl). Mean urinary THBMA concentrations in smokers and non-smokers were found to be 21.6 and 13.7 ng/mg creatinine, respectively, suggesting that there are sources of THBMA other than exposure to tobacco smoke in humans, as is also the case for DHBMA. However, THBMA concentrations are significantly greater in urine of smokers than that of non-smokers (p < 0.01). Furthermore, THBMA amounts in human urine declined 25–50 % following smoking cessation, suggesting that smoking is an important source of this metabolite in humans. The HPLC-ESI−-MS/MS methodology developed in the present work will be useful for future epidemiological studies of BD exposure and metabolism. PMID:21749114

Houston’s rapid ozone increases: preconditions and geographic origins

PubMed Central

Couzo, Evan; Jeffries, Harvey E.; Vizuete, William

2013-01-01

Many of Houston’s highest 8-h ozone (O3) peaks are characterised by increases in concentrations of at least 40 ppb in 1 h, or 60 ppb in 2 h. These rapid increases are called non-typical O3 changes (NTOCs). In 2004, the Texas Commission on Environmental Quality (TCEQ) developed a novel emissions control strategy aimed at eliminating NTOCs. The strategy limited routine and short-term emissions of ethene, propene, 1,3-butadiene and butene isomers, collectively called highly reactive volatile organic compounds (HRVOCs), which are released from petrochemical facilities. HRVOCs have been associated with NTOCs through field campaigns and modelling studies. This study analysed wind measurements and O3, formaldehyde (HCHO) and sulfur dioxide (SO2) concentrations from 2000 to 2011 at 25 ground monitors in Houston. NTOCs almost always occurred when monitors were downwind of petrochemical facilities. Rapid O3 increases were associated with low wind speeds; 75 % of NTOCs occurred when the 3-h average wind speed preceding the event was less than 6.5 km h−1. Statistically significant differences in HCHO concentrations were seen between days with and without NTOCs. Early afternoon HCHO concentrations were greater on NTOC days. In the morning before an observed NTOC event, however, there were no significant differences in HCHO concentrations between days with and without NTOCs. Hourly SO2 concentrations also increased rapidly, exhibiting behaviour similar to NTOCs. Oftentimes, the SO2 increases preceded a NTOC. These findings show that, despite the apparent success of targeted HRVOC emission controls, further restrictions may be needed to eliminate the remaining O3 events. PMID:24014080

Transient increases in methylbutenol emission following partial defoliation of Pinus ponderosa

NASA Astrophysics Data System (ADS)

Gray, Dennis W.

Methybutenol (MBO or 2-methyl-3-butene-2-ol) is a five-carbon alcohol produced and emitted in large amounts by many species of pine native to Western North America. Upon entering the atmosphere, MBO may engage in a series of chemical reactions which may ultimately lead to the production of tropospheric ozone which is a damaging pollutant. While the physical factors controlling MBO emission are well understood, the ecological factors controlling MBO emission have yet to be addressed. This study examines the response of MBO emission from Pinus ponderosa to herbivory simulated by needle clipping. Following defoliation early in the season, MBO emission from some plants tripled but similar increase did not occur later in the season. Anecdotal evidence suggests that the variable response of MBO emission to defoliation may have been due to the action of insect herbivores early in the season, or may have been due to phenological changes in the plants over the course of the season.

Moessbauer spectra of ferrite catalysts used in oxidative dehydrogenation

NASA Technical Reports Server (NTRS)

Cares, W. R.; Hightower, J. W.

1971-01-01

Room temperature Mossbauer spectroscopy was used to examine bulk changes which occur in low surface area CoFe2O4 and CuFe2O4 catalysts as a result of contact with various mixtures of trans-2-butene and O2 during oxidative dehydrogenation reactions at about 420 C. So long as there was at least some O2 in the gas phase, the CoFe2O4 spectrum was essentially unchanged. However, the spectrum changed from a random spinel in the oxidized state to an inverse spinel as it was reduced by oxide ion removal. The steady state catalyst lies very near the fully oxidized state. More dramatic solid state changes occurred as the CuFe2O4 underwent reduction. Under severe reduction, the ferrite was transformed into Cu and Fe3O4, but it could be reversibly recovered by oxidation. An intense doublet located near zero velocity persisted in all spectra of CuFe2O4 regardless of the state of reduction.

Differences in Butadiene Adduct Formation between Rats and Mice Not Due to Selective Inhibition of CYP2E1 by Butadiene Metabolites

PubMed Central

Pianalto, Kaila M.; Hartman, Jessica H.; Boysen, Gunnar; Miller, Grover P.

2013-01-01

CYP2E1 metabolizes 1,3-butadiene (BD) into genotoxic and possibly carcinogenic 1,2-epoxy-3-butene (EB), 1,2:3,4-diepoxybutane (DEB), and 1,2-epoxy-3,4-butanediol (EB-diol). The dose response of DNA and protein adducts derived from BD metabolites increase linearly at low BD exposures and then saturate at higher exposures in rats, but not mice. It was hypothesized that differences in adduct formation between rodents reflect more efficient BD oxidation in mice than rats. Herein, we assessed whether BD-derived metabolites selectively inhibit rat but not mouse CYP2E1 activity using B6C3F1 mouse and Fisher 344 rat liver microsomes. Basal CYP2E1 activities toward 4-nitrophenol were similar between rodents. Through IC50 studies, EB was the strongest inhibitor (IC50 54 μM, mouse; 98 μM, rat), BD-diol considerably weaker (IC50 1200 μM, mouse; 1000 μM, rat), and DEB inhibition nonexistent (IC50 >25 mM). Kinetic studies showed that in both species EB and BD-diol inhibited 4-nitrophenol oxidation through two-site mechanisms in which inhibition constants reflected trends observed in IC50 studies. None of the reactive epoxide metabolites inactivated CYP2E1 irreversibly. Thus, there was no selective inhibition or inactivation of rat CYP2E1 by BD metabolites relative to mouse Cyp2e1, and it can be inferred that CYP2E1 activity toward BD between rodent species would similarly not be impacted by the presence of BD metabolites. Inhibition of CYP2E1 by BD metabolites is then not responsible for the reported species difference in BD metabolism, formation of BD-derived DNA and protein adducts, mutagenicity and tumorigenesis. PMID:24021170

Differences in butadiene adduct formation between rats and mice not due to selective inhibition of CYP2E1 by butadiene metabolites.

PubMed

Pianalto, Kaila M; Hartman, Jessica H; Boysen, Gunnar; Miller, Grover P

2013-11-25

CYP2E1 metabolizes 1,3-butadiene (BD) into genotoxic and possibly carcinogenic 1,2-epoxy-3-butene (EB), 1,2:3,4-diepoxybutane (DEB), and 1,2-epoxy-3,4-butanediol (EB-diol). The dose response of DNA and protein adducts derived from BD metabolites increases linearly at low BD exposures and then saturates at higher exposures in rats, but not mice. It was hypothesized that differences in adduct formation between rodents reflect more efficient BD oxidation in mice than rats. Herein, we assessed whether BD-derived metabolites selectively inhibit rat but not mouse CYP2E1 activity using B6C3F1 mouse and Fisher 344 rat liver microsomes. Basal CYP2E1 activities toward 4-nitrophenol were similar between rodents. Through IC50 studies, EB was the strongest inhibitor (IC50 54μM, mouse; 98μM, rat), BD-diol considerably weaker (IC50 1200μM, mouse; 1000μM, rat), and DEB inhibition nonexistent (IC50>25mM). Kinetic studies showed that in both species EB and BD-diol inhibited 4-nitrophenol oxidation through two-site mechanisms in which inhibition constants reflected trends observed in IC50 studies. None of the reactive epoxide metabolites inactivated CYP2E1 irreversibly. Thus, there was no selective inhibition or inactivation of rat CYP2E1 by BD metabolites relative to mouse Cyp2e1, and it can be inferred that CYP2E1 activity toward BD between rodent species would similarly not be impacted by the presence of BD metabolites. Inhibition of CYP2E1 by BD metabolites is then not responsible for the reported species difference in BD metabolism, formation of BD-derived DNA and protein adducts, mutagenicity and tumorigenesis. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

On-board measurements of gaseous pollutant emission characteristics under real driving conditions from light-duty diesel vehicles in Chinese cities.

PubMed

Wang, Gang; Cheng, Shuiyuan; Lang, Jianlei; Li, Song; Tian, Liang

2016-08-01

A total of 15 light-duty diesel vehicles (LDDVs) were tested with the goal of understanding the emission factors of real-world vehicles by conducting on-board emission measurements. The emission characteristics of hydrocarbons (HC) and nitrogen oxides (NOx) at different speeds, chemical species profiles and ozone formation potential (OFP) of volatile organic compounds (VOCs) emitted from diesel vehicles with different emission standards were analyzed. The results demonstrated that emission reductions of HC and NOx had been achieved as the control technology became more rigorous from Stage I to Stage IV. It was also found that the HC and NOx emissions and percentage of O2 dropped with the increase of speed, while the percentage of CO2 increased. The abundance of alkanes was significantly higher in diesel vehicle emissions, approximately accounting for 41.1%-45.2%, followed by aromatics and alkenes. The most abundant species were propene, ethane, n-decane, n-undecane, and n-dodecane. The maximum incremental reactivity (MIR) method was adopted to evaluate the contributions of individual VOCs to OFP. The results indicated that the largest contributors to O3 production were alkenes and aromatics, which accounted for 87.7%-91.5%. Propene, ethene, 1,2,4-trimethylbenzene, 1-butene, and 1,2,3-trimethylbenzene were the top five VOC species based on their OFP, and accounted for 54.0%-64.8% of the total OFP. The threshold dilution factor was applied to analyze the possibility of VOC stench pollution. The majority of stench components emitted from vehicle exhaust were aromatics, especially p-diethylbenzene, propylbenzene, m-ethyltoluene, and p-ethyltoluene. Copyright © 2016. Published by Elsevier B.V.

Aqueous oxidation of green leaf volatiles by hydroxyl radical as a source of SOA: Kinetics and SOA yields

NASA Astrophysics Data System (ADS)

Richards-Henderson, Nicole K.; Hansel, Amie K.; Valsaraj, Kalliat T.; Anastasio, Cort

2014-10-01

Green leaf volatiles (GLVs) are a class of oxygenated hydrocarbons released from vegetation, especially during mechanical stress or damage. The potential for GLVs to form secondary organic aerosol (SOA) via aqueous-phase reactions is not known. Fog events over vegetation will lead to the uptake of GLVs into water droplets, followed by aqueous-phase reactions with photooxidants such as the hydroxyl radical (OH). In order to determine if the aqueous oxidation of GLVs by OH can be a significant source of secondary organic aerosol, we studied the partitioning and reaction of five GLVs: cis-3-hexen-1-ol, cis-3-hexenyl acetate, methyl salicylate, methyl jasmonate, and 2-methyl-3-butene-2-ol. For each GLV we measured the kinetics of aqueous oxidation by OH, and the corresponding SOA mass yield. The second-order rate constants for GLVs with OH were all near diffusion controlled, (5.4-8.6) × 109 M-1 s-1 at 298 K, and showed a small temperature dependence, with an average activation energy of 9.3 kJ mol-1 Aqueous-phase SOA mass yields ranged from 10 to 88%, although some of the smaller values were not statistically different from zero. Methyl jasmonate was the most effective aqueous-phase SOA precursor due to its larger Henry's law constant and high SOA mass yield (68 ± 8%). While we calculate that the aqueous-phase SOA formation from the five GLVs is a minor source of aqueous-phase SOA, the availability of other GLVs, other oxidants, and interfacial reactions suggest that GLVs overall might be a significant source of SOA via aqueous reactions.

Spectroscopic investigation of H atom transfer in a gas-phase dissociation reaction: McLafferty rearrangement of model gas-phase peptide ions.

PubMed

Van Stipdonk, Michael J; Kerstetter, Dale R; Leavitt, Christopher M; Groenewold, Gary S; Steill, Jeffrey; Oomens, Jos

2008-06-14

Wavelength-selective infrared multiple-photon photodissociation (WS-IRMPD) was used to study isotopically-labeled ions generated by McLafferty rearrangement of nicotinyl-glycine-tert-butyl ester and betaine-glycine-tert-butyl ester. The tert-butyl esters were incubated in a mixture of D(2)O and CH(3)OD to induce solution-phase hydrogen-deuterium exchange and then converted to gas-phase ions using electrospray ionization. McLafferty rearrangement was used to generate the free-acid forms of the respective model peptides through transfer of an H atom and elimination of butene. The specific aim was to use vibrational spectra generated by WS-IRMPD to determine whether the H atom remains at the acid group, or migrates to one or more of the other exchangeable sites. Comparison of the IRMPD results in the region from 1200-1900 cm(-1) to theoretical spectra for different isotopically-labeled isomers clearly shows that the H atom is situated at the C-terminal acid group and migration to amide positions is negligible on the time scale of the experiment. The results of this study suggest that use of the McLafferty rearrangement for peptide esters could be an effective approach for generation of H-atom isotope tracers, in situ, for subsequent investigation of intramolecular proton migration during peptide fragmentation studies.

Catalyst and process development for synthesis gas conversion to isobutylene. Final report, September 1, 1990--January 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anthony, R.G.; Akgerman, A.

1994-05-06

Previous work on isosynthesis (conversion of synthesis gas to isobutane and isobutylene) was performed at very low conversions or extreme process conditions. The objectives of this research were (1) determine the optimum process conditions for isosynthesis; (2) determine the optimum catalyst preparation method and catalyst composition/properties for isosynthesis; (3) determine the kinetics for the best catalyst; (4) develop reactor models for trickle bed, slurry, and fixed bed reactors; and (5) simulate the performance of fixed bed trickle flow reactors, slurry flow reactors, and fixed bed gas phase reactors for isosynthesis. More improvement in catalyst activity and selectivity is needed beforemore » isosynthesis can become a commercially feasible (stand-alone) process. Catalysts prepared by the precipitation method show the most promise for future development as compared with those prepared hydrothermally, by calcining zirconyl nitrate, or by a modified sol-gel method. For current catalysts the high temperatures (>673 K) required for activity also cause the production of methane (because of thermodynamics). A catalyst with higher activity at lower temperatures would magnify the unique selectivity of zirconia for isobutylene. Perhaps with a more active catalyst and acidification, oxygenate production could be limited at lower temperatures. Pressures above 50 atm cause an undesirable shift in product distribution toward heavier hydrocarbons. A model was developed that can predict carbon monoxide conversion an product distribution. The rate equation for carbon monoxide conversion contains only a rate constant and an adsorption equilibrium constant. The product distribution was predicted using a simple ratio of the rate of CO conversion. This report is divided into Introduction, Experimental, and Results and Discussion sections.« less

Broadband mid-infrared and THz chemical detection with quantum cascade laser multi-heterodyne spectrometers (Conference Presentation)

NASA Astrophysics Data System (ADS)

Westberg, Jonas; Sterczewski, Lukasz A.; Patrick, Link; Wysocki, Gerard

2017-05-01

Majority of chemical species of interest in security and safety applications (e.g. explosives) have complex molecular structures that produce unresolved rotational-vibrational spectroscopic signatures in the mid-infrared. This requires spectroscopic techniques that can provide broadband coverage in the mid-IR region to target broadband absorbers and high resolution to address small molecules that exhibit well-resolved spectral lines. On the other hand, many broadband mid-IR absorbers exhibit well-resolved rotational components in the THz spectral region. Thus, development of spectroscopic sensing technologies that can address both spectral regions is of great importance. Here we demonstrate recent progress towards broadband high-resolution spectroscopic sensing applications with Fabry-Perot quantum cascade lasers (QCLs) and frequency combs using multi-heterodyne spectroscopy (MHS) techniques. In this paper, we will present spectroscopic sensing of large and small molecules in the mid-IR region using QCLs operating at 8.5µm. An example high-resolution, broadband MHS of ammonia (small molecule) and isobutane (broadband absorber) at atmospheric pressure in the 1165-1190 cm^-1 range will be discussed. We have developed a balanced MHS system for mitigation of the laser intensity fluctuations. Absorption spectroscopy as well as dispersion spectroscopy with minimum fractional absorption down to 10^-4/Hz1/2 and fast spectral acquisition capabilities down to 10 µs/spectrum range will be demonstrated. In order to mitigate the shortcomings of the limited chemical selectivity in the mid-IR, THz QCL based spectrometer is currently under development to provide spectral de-congestion and thus significantly improve chemical identification. Preliminary characterization of the performance of THZ QCL combs for the THz QCL-MHS will be presented.

OH and halogen atom influence on the variability of non-methane hydrocarbons in the Antarctic Boundary Layer

NASA Astrophysics Data System (ADS)

Read, Katie A.; Lewis, Alastair C.; Salmon, Rhian A.; Jones, Anna E.; Bauguitte, Stéphane

2007-02-01

Measurements of C2-C8 non-methane hydrocarbons (NMHCs) have been made in situ at Halley Base, Antarctica (75°35'S, 26°19'W) from February 2004 to February 2005 as part of the Chemistry of the Antarctic Boundary Layer and the Interface with Snow (CHABLIS) experiment. The data show long- and short-term variabilities in NMHCs controlled by the seasonal and geographic dependence of emissions and variation in atmospheric removal rates and pathways. Ethane, propane, iso-butane, n-butane and acetylene abundances followed a general OH-dependent sinusoidal seasonal cycle. The yearly averages were 186, 31, 3.2, 4.9 and 19 pptV, respectively, lower than those which were reported in some previous studies. Superimposed on a seasonal cycle was shorter-term variability that could be attributed to both synoptic airmass variability and localized loss processes due to other radical species. Hydrocarbon variability during periods of hour-to-day-long surface O3 depletion in late winter/early spring indicated active halogen atom chemistry estimated to be in the range 1.7 × 103-3.4 × 104 atom cm-3 for Cl and 4.8 × 106-9.6 × 107 atom cm-3 for Br. Longer-term negative deviations from sinusoidal behaviour in the late August were indicative of NMHC reaction with a persistent [Cl] of 2.3 × 103 atom cm-3. Maximum ethene and propene of 157 and 179 pptV, respectively, were observed in the late February/early March, consistent with increased oceanic biogenic emissions; however, their presence was significant year-round (June-August concentrations of 17.1 +/- 18.3 and 7.9 +/- 20.0 pptV, respectively).

Exposure-Response of 1,2:3,4-Diepoxybutane–Specific N-Terminal Valine Adducts in Mice and Rats after Inhalation Exposure to 1,3-Butadiene

PubMed Central

Georgieva, Nadia I.; Boysen, Gunnar; Bordeerat, Narisa; Walker, Vernon E.; Swenberg, James A.

2010-01-01

1,3-Butadiene (BD) is a known rodent and human carcinogen that is metabolized mainly by P450 2E1 to three epoxides, 1,2-epoxy-3-butene (EB), 1,2:3,4-diepoxybutane (DEB), and 1,2-epoxy-3,4-butanediol. The individual epoxides vary up to 200-fold in their mutagenic potency, with DEB being the most mutagenic metabolite. It is important to understand the internal formation of the individual epoxides to assign the relative risk for each metabolite and to understand the molecular mechanisms responsible for extensive species differences in carcinogenicity. This study presents a comprehensive exposure-response for the formation of the DEB-specific N,N-(2,3-dihydroxy-1,4-butadiyl)valine (pyr-Val) in mice and rats. Using nano-ultra high pressure liquid chromatography-tandem-mass spectrometry allowed analysis of pyr-Val in mice and rats exposed to BD as low as 0.1 and 0.5 ppm BD, respectively, and demonstrated significant differences in the amounts and exposure-response of pyr-Val formation. Mice formed 10- to 60-fold more pyr-Val compared to rats at similar exposures. The formation of pyr-Val increased with exposures, and the formation was most efficient with regard to formation per parts per million BD at low exposures. While formation at higher exposures appeared linear in mice, in rats formation saturated at exposures ≥ 200 ppm for 10 days. In rats, amounts of pyr-Val were lower after 20 days than after 10 days of exposure, suggesting that the lifespan of rat erythrocytes may be shortened following exposure to BD. This research supports the hypothesis that the lower susceptibility of rats to BD-induced carcinogenesis results from greatly reduced formation of DEB following exposure to BD. PMID:20176624

Multi-year levels and trends of non-methane hydrocarbon concentrations observed in ambient air in France

NASA Astrophysics Data System (ADS)

Waked, Antoine; Sauvage, Stéphane; Borbon, Agnès; Gauduin, Julie; Pallares, Cyril; Vagnot, Marie-Pierre; Léonardis, Thierry; Locoge, Nadine

2016-09-01

Measurements of 31 non-methane hydrocarbons (NMHCs) were carried out at three urban (Paris, 2003-2014, Strasbourg, 2002-2014 and Lyon, 2007-2014) sites in France over the period of a decade. A trend analysis was applied by means of the Mann-Kendall non-parametric test to annual and seasonal mean concentrations in order to point out changes in specific emission sources and to assess the impact of emission controls and reduction strategies. The trends were compared to those from three rural sites (Peyrusse-Vieille, 2002-2013, Tardière, 2003-2013 and Donon, 1997-2007). The results obtained showed a significant yearly decrease in pollutant concentrations over the study period and for the majority of species in the range of -1 to -7% in accordance with the decrease of NMHC emissions in France (-5 to -9%). Concentrations of long-lived species such as ethane and propane which are recognized as tracers of distant sources and natural gas remained constant. Compounds associated with combustion processes such as acetylene, propene, ethylene and benzene showed a significant decline in the range of -2% to -5% yr-1. These trends are consistent with those recently described at urban and background sites in the northern mid-latitudes and with emission inventories. C7-C9 aromatics such as toluene and xylenes as well as C4-C5 alkanes such as isopentane and isobutane also showed a significant decrease in the range of -3% to -7% yr-1. The decreasing trends in terms of % yr-1 observed at these French urban sites were typically higher for acetylene, ethylene and benzene than those reported for French rural sites of the national observatory of Measurement and Evaluation in Rural areas of trans-boundary Air pollution (MERA). The study also highlighted the difficult choice of a long term sampling site representative of the general trends of pollutant concentrations.

Analysis of 62 synthetic cannabinoids by gas chromatography-mass spectrometry with photoionization.

PubMed

Akutsu, Mamoru; Sugie, Ken-Ichi; Saito, Koichi

2017-01-01

Gas chromatography-mass spectrometry (GC-MS) in electron ionization (EI) mode is one of the most commonly used techniques for analysis of synthetic cannabinoids, because the GC-EI-MS spectra contain characteristic fragment ions for identification of a compound; however, the information on its molecular ions is frequently lacking. To obtain such molecular ion information, GC-MS in chemical ionization (CI) mode is frequently used. However, GC-CI-MS requires a relatively tedious process using reagent gas such as methane or isobutane. In this study, we show that GC-MS in photoionization (PI) mode provided molecular ions in all spectra of 62 synthetic cannabinoids, and 35 of the 62 compounds showed only the molecular radical cations. Except for the 35 compounds, the PI spectra showed very simple patterns with the molecular peak plus only a few fragment peak(s). An advantage is that the ion source for GC-PI-MS can easily be used for GC-EI-MS as well. Therefore, GC-EI/PI-MS will be a useful tool for the identification of synthetic cannabinoids contained in a dubious product. To the best of our knowledge, this is the first report to use GC-PI-MS for analysis of synthetic cannabinoids.

Determination of volatile organic compounds in human breath for Helicobacter pylori detection by SPME-GC/MS.

PubMed

Ulanowska, Agnieszka; Kowalkowski, Tomasz; Hrynkiewicz, Katarzyna; Jackowski, Marek; Buszewski, Bogusław

2011-03-01

Helicobacter pylori living in the human stomach release volatile organic compounds (VOCs) that can be detected in expired air. The aim of the study was the application of breath analysis for bacteria detection. It was accomplished by determination of VOCs characteristic for patients with H. pylori and the analysis of gases released by bacteria in suspension. Solid-phase microextraction was applied as a selective technique for preconcentration and isolation of analytes. Gas chromatography coupled with mass spectrometry was used for the separation and identification of volatile analytes in breath samples and bacterial headspace. For data calculation and processing, discriminant and factor analyses were used. Endogenous substances such as isobutane, 2-butanone and ethyl acetate were detected in the breath of persons with H. pylori in the stomach and in the gaseous mixture released by the bacteria strain but they were not identified in the breath of healthy volunteers. The canonical analysis of discrimination functions showed a strong difference between the three examined groups. Knowledge of substances emitted by H. pylori with the application of an optimized breath analysis method might become a very useful tool for noninvasive detection of this bacterium. Copyright © 2010 John Wiley & Sons, Ltd.

A Fiber Optic Interferometric Sensor Platform for Determining Gas Diffusivity in Zeolite Films.

PubMed

Yang, Ruidong; Xu, Zhi; Zeng, Shixuan; Jing, Wenheng; Trontz, Adam; Dong, Junhang

2018-04-04

Fiber optic interferometer (FOI) sensors have been fabricated by directly growing pure-silica MFI-type zeolite (i.e., silicalite) films on straight-cut endfaces of single-mode communication optical fibers. The FOI sensor has been demonstrated for determining molecular diffusivity in the zeolite by monitoring the temporal response of light interference from the zeolite film during the dynamic process of gas adsorption. The optical thickness of the zeolite film depends on the amount of gas adsorption that causes the light interference to shift upon loading molecules into the zeolitic channels. Thus, the time-dependence of the optical signal reflected from the coated zeolite film can represent the adsorption uptake curve, which allows computation of the diffusivity using models derived from the Fick’s Law equations. In this study, the diffusivity of isobutane in silicalite has been determined by the new FOI sensing method, and the results are in good agreement with literature values obtained by various conventional macroscopic techniques. The FOI sensor platform, because of its robustness and small size, could be useful for studying molecular diffusion in zeolitic materials under conditions that are inaccessible to the existing techniques.

Recovery of energy from geothermal brine and other hot water sources

DOEpatents

Wahl, III, Edward F.; Boucher, Frederic B.

1981-01-01

Process and system for recovery of energy from geothermal brines and other hot water sources, by direct contact heat exchange between the brine or hot water, and an immiscible working fluid, e.g. a hydrocarbon such as isobutane, in a heat exchange column, the brine or hot water therein flowing countercurrent to the flow of the working fluid. The column can be operated at subcritical, critical or above the critical pressure of the working fluid. Preferably, the column is provided with a plurality of sieve plates, and the heat exchange process and column, e.g. with respect to the design of such plates, number of plates employed, spacing between plates, area thereof, column diameter, and the like, are designed to achieve maximum throughput of brine or hot water and reduction in temperature differential at the respective stages or plates between the brine or hot water and the working fluid, and so minimize lost work and maximize efficiency, and minimize scale deposition from hot water containing fluid including salts, such as brine. Maximum throughput approximates minimum cost of electricity which can be produced by conversion of the recovered thermal energy to electrical energy.

Influences of the molecular fuel structure on combustion reactions towards soot precursors in selected alkane and alkene flames.

PubMed

Ruwe, Lena; Moshammer, Kai; Hansen, Nils; Kohse-Höinghaus, Katharina

2018-04-25

In this study, we experimentally investigate the high-temperature oxidation kinetics of n-pentane, 1-pentene and 2-methyl-2-butene (2M2B) in a combustion environment using flame-sampling molecular beam mass spectrometry. The selected C5 fuels are prototypes for linear and branched, saturated and unsaturated fuel components, featuring different C-C and C-H bond structures. It is shown that the formation tendency of species, such as polycyclic aromatic hydrocarbons (PAHs), yielded through mass growth reactions increases drastically in the sequence n-pentane < 1-pentene < 2M2B. This comparative study enables valuable insights into fuel-dependent reaction sequences of the gas-phase combustion mechanism that provide explanations for the observed difference in the PAH formation tendency. First, we investigate the fuel-structure-dependent formation of small hydrocarbon species that are yielded as intermediate species during the fuel decomposition, because these species are at the origin of the subsequent mass growth reaction pathways. Second, we review typical PAH formation reactions inspecting repetitive growth sequences in dependence of the molecular fuel structure. Third, we discuss how differences in the intermediate species pool influence the formation reactions of key aromatic ring species that are important for the PAH growth process underlying soot formation. As a main result it was found that for the fuels featuring a C[double bond, length as m-dash]C double bond, the chemistry of their allylic fuel radicals and their decomposition products strongly influences the combination reactions to the initially formed aromatic ring species and as a consequence, the PAH formation tendency.

Aqueous Oxidation of Green Leaf Volatiles as a Source of Secondary Organic Aerosol

NASA Astrophysics Data System (ADS)

Richards-Henderson, N. K.; Hansel, A.; Pham, A. T.; Vempati, H. S.; Valsaraj, K. T.; Anastasio, C.

2013-12-01

Vegetation emits volatile oxygenated hydrocarbons - the green leaf volatiles (GLVs) - which are formed from the biochemical conversion of linoleic and linolenic acids within plant cells. Stress or damage to vegetation can significantly elevate emission fluxes of these compounds, some of which are fairly water soluble. Aqueous-phase reactions of the GLVs with photochemically generated oxidants - such as hydroxyl radical (OH), singlet oxygen (1O2) and excited triplet states of organic compounds (3C*) _ might then form low-volatility products that can act as secondary organic aerosol (SOA). In order to determine if GLVs can be a significant source of secondary organic carbon in fogwater, studies of GLVs in laboratory solutions are needed to elucidate the oxidation kinetics and the corresponding SOA mass yields. In this study we are determining the second-order rate constants, and SOA mass yields, for five GLVs (cis-3-hexen-1-ol, cis-3-hexenylacetate, methyl salicylate, methyl jasmonate, and 2-methyl-3-butene-2-ol) reacting with OH,1O2 and 3C*. Experiments are performed at relevant fog water pHs, temperatures, and oxidant concentrations. Rate constants are determined using a relative rate approach in which the decay of GLVs and reference compounds are monitored as function of time by HPLC. The capacity of GLVs to form aqueous SOA was determined by following the formation of their decomposition products with HPLC-UV/DAD and HPLC-ESI/MS. SOA mass yields are measured gravimetrically from laboratory solutions containing atmospherically relevant concentrations of photooxidants and GLVs, and irradiated with simulated sunlight. We will use our results to assess the potential contribution of aqueous GLV reactions as a source of SOA in cloudy or foggy atmospheres.

Meteorological and chemical impacts on ozone formation: A case study in Hangzhou, China

NASA Astrophysics Data System (ADS)

Li, Kangwei; Chen, Linghong; Ying, Fang; White, Stephen J.; Jang, Carey; Wu, Xuecheng; Gao, Xiang; Hong, Shengmao; Shen, Jiandong; Azzi, Merched; Cen, Kefa

2017-11-01

Regional ozone pollution has become one of the most challenging problems in China, especially in the more economically developed and densely populated regions like Hangzhou. In this study, measurements of O3, CO, NOx and non-methane hydrocarbons (NMHCs), together with meteorological data, were obtained for the period July 1, 2013-August 15, 2013 at three sites in Hangzhou. These sites included an urban site (Zhaohui ;ZH;), a suburban site (Xiasha ;XS;) and a rural site (Qiandaohu ;QDH;). During the observation period, both ZH and XS had a higher ozone level than QDH, with exceeding rates of 41.3% and 47.8%, respectively. Elevated O3 levels in QDH were found at night, which could be explained by less prominent NO titration effect in rural area. Detailed statistical analysis of meteorological and chemical impacts on ozone formation was carried out for ZH, and higher ozone concentration was observed when the wind direction was from the east. This is possibly due to emissions of VOCs from XS, a typical chemical industrial park located in 30 km upwind area of ZH. A comprehensive comparison between three ozone episode periods and one non-episode period were made in ZH. It was concluded that elevated concentrations of precursors and temperatures, low relative humidity and wind speed and easterly-dominated wind direction contribute to urban ozone episodes in Hangzhou. VOCs reactivity analysis indicated that reactive alkenes like isoprene and isobutene contributed most to ozone formation. Three methods were applied to evaluate O3-VOCs-NOx sensitivity in ZH: VOCs/NOx ratio method, Smog Production Model (SPM) and Relative Incremental Reactivity (RIR). The results show that summer ozone in urban Hangzhou mostly presents VOCs-limited and transition region alternately. Our study implies that the increasing automobiles and VOCs emissions from upwind area could result in ozone pollution in urban Hangzhou, and synergistic reduction of VOCs and NOx will be more effective.

Single Electron Delivery to Lewis Pairs: An Avenue to Anions by Small Molecule Activation.

PubMed

Liu, Liu Leo; Cao, Levy L; Shao, Yue; Stephan, Douglas W

2017-07-26

Single electron transfer (SET) reactions are effected by the combination of a Lewis acid (e.g., E(C 6 F 5 ) 3 E = B or Al) with a small molecule substrate and decamethylferrocene (Cp* 2 Fe). Initially, the corresponding reactions of (PhS) 2 and (PhTe) 2 were shown to give the species [Cp* 2 Fe][PhSB(C 6 F 5 ) 3 ] 1 and [Cp* 2 Fe][(μ-PhS)(Al(C 6 F 5 ) 3 ) 2 ] 2 and [Cp* 2 Fe][(μ-PhTe)(Al(C 6 F 5 ) 3 ) 2 ] 3, respectively. Analogous reactions with di-tert-butyl peroxide yielded [Cp* 2 Fe][(μ-HO)(B(C 6 F 5 ) 3 ) 2 ] 4 with isobutene while with benzoyl peroxide afforded [Cp* 2 Fe][PhC(O)OE(C 6 F 5 ) 3 ] (E = B 5, Al 6). Evidence for a radical pathway was provided by the reaction of Ph 3 SnH and p-quinone afforded [Cp* 2 Fe][HB(C 6 F 5 ) 3 ] 7 and [Cp* 2 Fe] 2 [(μ-O 2 C 6 H 4 )(E(C 6 F 5 ) 3 ) 2 ] (E = B 8, Al 9). In addition, the reaction of TEMPO with Lewis acid and Cp* 2 Fe afforded [Cp* 2 Fe][(C 5 H 6 Me 4 NOE(C 6 F 5 ) 3 ] (E = B 10, Al 11). Finally, reactions with O 2 , Se, Te and S 8 gave [Cp* 2 Fe] 2 [((C 6 F 5 ) 2 Al(μ-O)Al(C 6 F 5 ) 3 ) 2 ] 2 12, [Cp* 2 Fe] 2 [((C 6 F 5 ) 2 Al(μ-Se)Al(C 6 F 5 ) 3 ) 2 ] 2 13, [Cp* 2 Fe][(μ-Te) 2 (Al(C 6 F 5 ) 2 ) 3 ] 14 and [Cp* 2 Fe] 2 [(μ-S 7 )B(C 6 F 5 ) 3 ) 2 ] 15, respectively. The mechanisms of these SET reactions are discussed, and the ramifications are considered.

Forensic analysis of tertiary-butyl alcohol (TBA) detections in a hydrocarbon-rich groundwater basin.

PubMed

Quast, Konrad W; Levine, Audrey D; Kester, Janet E; Fordham, Carolyn L

2016-04-01

Tertiary-butyl alcohol (TBA), a high-production volume (HPV) chemical, was sporadically detected in groundwater and coalbed methane (CBM) wells in southeastern Colorado's hydrocarbon-rich Raton Basin. TBA concentrations in shallow water wells averaged 75.1 μg/L, while detections in deeper CBM wells averaged 14.4 μg/L. The detection of TBA prompted a forensic investigation to try to identify potential sources. Historic and recent data were reviewed to determine if there was a discernable pattern of TBA occurrence. Supplemental samples from domestic water wells, monitor wells, CBM wells, surface waters, and hydraulic fracturing (HF) fluids were analyzed for TBA in conjunction with methyl tertiary-butyl ether (MTBE) and ethyl tertiary-butyl ether (ETBE), proxies for evidence of contamination from reformulated gasoline or associated oxygenates. Exploratory microbiological sampling was conducted to determine if methanotrophic organisms co-occurred with TBA in individual wells. Meaningful comparisons of historic TBA data were limited due to widely varying reporting limits. Mapping of TBA occurrence did not reveal any spatial patterns or physical associations with CBM operations or contamination plumes. Additionally, TBA was not detected in HF fluids or surface water samples. Given the widespread use of TBA in industrial and consumer products, including water well completion materials, it is likely that multiple diffuse sources exist. Exploratory data on stable isotopes, dissolved gases, and microbial profiling provide preliminary evidence that methanotrophic activity may be producing TBA from naturally occurring isobutane. Reported TBA concentrations were significantly below a conservative risk-based drinking water screening level of 8000 μg/L derived from animal toxicity data.

Quantification of Methane Leaks from Abandoned Oil and Gas Wells in California

NASA Astrophysics Data System (ADS)

Lebel, E.; Kang, M.; Lu, H.; Jackson, R. B.

2016-12-01

Abandoned oil and gas wells can provide a pathway for subterranean methane and other gases to be emitted to the atmosphere. However, abandoned wells are unaccounted for in greenhouse gas emissions inventories. While relatively little is known about abandoned wells, previous studies have shown that emissions from abandoned wells contribute approximately 4-7% of anthropogenic methane emissions in Pennsylvania (Kang et al. 2014) and <1% of regional methane emissions in oil and gas producing regions of Colorado, Utah, Ohio, and Wyoming (Townsend-Small et al. 2015). Another study (Boothroyd et al. 2016) has shown that 30% of abandoned wells in the UK have a positive surface methane flux. California has a long history of oil and gas production, beginning from the 1860s, and currently ranks third in oil production by state. As a result, there are more than 100,000 wells across the state. Our study uses static flux chambers to measure individual abandoned wells in California to estimate state-wide methane emissions from these wells. In addition to measuring methane concentrations, we measure ethane, propane, isobutane, n-butane, and 13-CH4 to understand whether this methane has a biogenic or thermogenic source. We hope that our research will determine whether or not abandoned oil and gas wells are a significant source of anthropogenic methane emissions in California. Our results along with measurements in other parts of the United States can be used to scale up methane emission estimates to the national level, accounting for the millions of abandoned wells in the country.

A study of ethanol reactions on O2-treated Au/TiO2. Effect of support and metal loading on reaction selectivity

NASA Astrophysics Data System (ADS)

Nadeem, M. A.; Waterhouse, G. I. N.; Idriss, H.

2016-08-01

The reactions of ethanol have been studied on bare and Au supported TiO2 polymorphs (anatase and rutile) in order to understand the effect of Au loading and prior O2 treatment on the reaction selectivity and conversion using temperature programmed desorption (TPD). Although O2 treatment has negligible effect on the reaction selectivity of ethanol on TiO2 alone it considerably affects the reaction on Au/TiO2. Au/TiO2 had three main effects on the reaction when compared to TiO2 alone. First, it switches the reaction selectivity of the dehydration (to ethylene) in favor of dehydrogenation (to acetaldehyde) on both polymorphs. Second, it decreases the desorption temperature of the main reaction products. Third, it increases secondary reaction products (mainly C4 (crotonaldehyde, butene, furan) reaching ca. 78% of the overall carbon selectivity for the 8 wt.% Au/TiO2 anatase. These effects are more pronounced on the anatase phase when compared to that on the rutile phase. Reasons for these are discussed.

Entrapped Single Tungstate Site in Zeolite for Cooperative Catalysis of Olefin Metathesis with Brønsted Acid Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Pu; Ye, Lin; Sun, Zhenyu

Industrial olefin metathesis catalysts generally suffer from low reaction rates and require harsh reaction conditions for moderate activities. This is due to their inability to prevent metathesis active sites (MAS) from aggregation and their intrinsic poor adsorption and activation of olefin molecules. Here, isolated tungstate species as single molecular MAS is immobilized inside zeolite pores by Bronsted acid sites (BAS) on the inner surface. It is demonstrated for the first time that unoccupied BAS in atomic proximity to MAS enhance olefin adsorption and greatly facilitate the formation of metallocycle intermediates in a stereospecific manner. Thus, effective cooperative catalysis takes placemore » over the BAS-MAS pair. In consequence, for the cross-metathesis of ethene and trans-2-butene to propene, under the same mild reaction conditions, the propene production rate over WOx/USY is ca. 7,300 times that over the industrial WO3/SiO2 based catalyst. A propene yield up to 79% (80% selectivity) without observable deactivation was obtained over WOx/USY for a wide range of reaction conditions.« less

Volatile aldehydes are promising broad-spectrum postharvest insecticides.

PubMed

Hammond, D G; Rangel, S; Kubo, I

2000-09-01

A variety of naturally occurring aldehydes common in plants have been evaluated for their insecticidal activity and for phytotoxicity to postharvest fruits, vegetables, and grains. Twenty-nine compounds were initially screened for their activity against aphids on fava bean leaf disks. Application under reduced pressure (partial vacuum) for the first quarter of fumigation increased insecticidal activity severalfold. The 11 best aldehydes were assayed against aphids placed under the third leaf of whole heads of iceberg lettuce using the same two-tier reduced-pressure regime, which caused no additional detriment to the commodity over fumigation at atmospheric pressure. Phytotoxicity to naked and wrapped iceburg lettuce, green and red table grapes, lemon, grapefruit, orange, broccoli, avocado, cabbage, pinto bean, and rice at doses that killed 100% of aphids was recorded for three promising fumigants: propanal, (E)-2-pentenal, and 2-methyl-(E)-2-butenal. These three compounds have excellent potential as affordable postharvest insect control agents, killing 100% of the aphids with little or no detectable harm to a majority of the commodities tested. Preliminary assays indicate that similar doses are also effective against mealybugs, thrips, and whitefly.

Efficient nitrogen incorporation in GaAs using novel metal organic As-N precursor di-tertiary-butyl-arsano-amine (DTBAA)

NASA Astrophysics Data System (ADS)

Sterzer, E.; Beyer, A.; Duschek, L.; Nattermann, L.; Ringler, B.; Leube, B.; Stegmüller, A.; Tonner, R.; von Hänisch, C.; Stolz, W.; Volz, K.

2016-04-01

III/V semiconductors containing small amounts of nitrogen (N; dilute nitrides) are discussed in the context of different solar cell and laser applications. The efficiency of these devices is negatively affected by carbon (C) incorporation, which comes either from the direct C-N bond in the N precursor unsymmetrical 1,1-dimethylhydrazine (UDMHy) used conventionally or from the alkyl groups of the conventional precursors for gallium (Ga), indium and arsenic (As) containing carbon. This C is incorporated together with the N due to the strength of the C-N bond. A further important issue in dilute nitride growth is the very low N incorporation efficiency in the crystal from UDMHy, which can be as little as 1% of the N supplied in the gas phase. Therefore, new metal organic chemicals have to be synthesized and their growth characteristics and suitability for dilute nitride growth have to be explored. This work presents the chemical di-tertiary-butyl-arsano-amine (DTBAA), which was synthesized, purified and tested as an N precursor for metal organic vapor phase epitaxy (MOVPE). Computational investigations show β-hydrogen and isobutane elimination to be the main reaction channel in the gas phase with high reaction barriers and absence of small fragments containing C as products. The loss of N via N2, as in UDMHy, can be excluded for unimolecular reactions of DTBAA. The Ga(NAs)/GaAs heterostructures were grown by MOVPE as initial test material and a systematic N incorporation study is presented in this paper. It is shown that high quality Ga(NAs) can be grown using DTBAA. The N incorporation was confirmed by high resolution X-ray diffraction and photoluminescence studies. All samples grown exhibit as grown room temperature photoluminescence and smooth surface morphologies. Furthermore, DTBAA shows extremely high N incorporation efficiency, which makes this molecule a very promising candidate for further research into dilute nitride material growth.

Sampling, storage, and analysis of C2-C7 non-methane hydrocarbons from the US National Oceanic and Atmospheric Administration Cooperative Air Sampling Network glass flasks.

PubMed

Pollmann, Jan; Helmig, Detlev; Hueber, Jacques; Plass-Dülmer, Christian; Tans, Pieter

2008-04-25

An analytical technique was developed to analyze light non-methane hydrocarbons (NMHC), including ethane, propane, iso-butane, n-butane, iso-pentane, n-pentane, n-hexane, isoprene, benzene and toluene from whole air samples collected in 2.5l-glass flasks used by the National Oceanic and Atmospheric Administration, Earth System Research Laboratory, Global Monitoring Division (NOAA ESRL GMD, Boulder, CO, USA) Cooperative Air Sampling Network. This method relies on utilizing the remaining air in these flasks (which is at below-ambient pressure at this stage) after the completion of all routine greenhouse gas measurements from these samples. NMHC in sample aliquots extracted from the flasks were preconcentrated with a custom-made, cryogen-free inlet system and analyzed by gas chromatography (GC) with flame ionization detection (FID). C2-C7 NMHC, depending on their ambient air mixing ratios, could be measured with accuracy and repeatability errors of generally < or =10-20%. Larger deviations were found for ethene and propene. Hexane was systematically overestimated due to a chromatographic co-elution problem. Saturated NMHC showed less than 5% changes in their mixing ratios in glass flask samples that were stored for up to 1 year. In the same experiment ethene and propene increased at approximately 30% yr(-1). A series of blank experiments showed negligible contamination from the sampling process and from storage (<10 pptv yr(-1)) of samples in these glass flasks. Results from flask NMHC analyses were compared to in-situ NMHC measurements at the Global Atmospheric Watch station in Hohenpeissenberg, Germany. This 9-months side-by-side comparison showed good agreement between both methods. More than 94% of all data comparisons for C2-C5 alkanes, isoprene, benzene and toluene fell within the combined accuracy and precision objectives of the World Meteorological Organization Global Atmosphere Watch (WMO-GAW) for NMHC measurements.

Gas phase carbonyl compounds in ship emissions: Differences between diesel fuel and heavy fuel oil operation

NASA Astrophysics Data System (ADS)

Reda, Ahmed A.; Schnelle-Kreis, J.; Orasche, J.; Abbaszade, G.; Lintelmann, J.; Arteaga-Salas, J. M.; Stengel, B.; Rabe, R.; Harndorf, H.; Sippula, O.; Streibel, T.; Zimmermann, R.

2014-09-01

Gas phase emission samples of carbonyl compounds (CCs) were collected from a research ship diesel engine at Rostock University, Germany. The ship engine was operated using two different types of fuels, heavy fuel oil (HFO) and diesel fuel (DF). Sampling of CCs was performed from diluted exhaust using cartridges and impingers. Both sampling methods involved the derivatization of CCs with 2,4-Dinitrophenylhydrazine (DNPH). The CCs-hydrazone derivatives were analyzed by two analytical techniques: High Performance Liquid Chromatography-Diode Array Detector (HPLC-DAD) and Gas Chromatography-Selective Ion Monitoring-Mass Spectrometry (GC-SIM-MS). Analysis of DNPH cartridges by GC-SIM-MS method has resulted in the identification of 19 CCs in both fuel operations. These CCs include ten aliphatic aldehydes (formaldehyde, acetaldehyde, propanal, isobutanal, butanal, isopentanal, pentanal, hexanal, octanal, nonanal), three unsaturated aldehydes (acrolein, methacrolein, crotonaldehyde), three aromatic aldehyde (benzaldehyde, p-tolualdehyde, m,o-molualdehyde), two ketones (acetone, butanone) and one heterocyclic aldehyde (furfural). In general, all CCs under investigation were detected with higher emission factors in HFO than DF. The total carbonyl emission factor was determined and found to be 6050 and 2300 μg MJ-1 for the operation with HFO and DF respectively. Formaldehyde and acetaldehyde were found to be the dominant carbonyls in the gas phase of ship engine emission. Formaldehyde emissions factor varied from 3500 μg MJ-1 in HFO operation to 1540 μg MJ-1 in DF operation, which is 4-30 times higher than those of other carbonyls. Emission profile contribution of CCs showed also a different pattern between HFO and DF operation. The contribution of formaldehyde was found to be 58% of the emission profile of HFO and about 67% of the emission profile of DF. Acetaldehyde showed opposite behavior with higher contribution of 16% in HFO compared to 11% for DF. Heavier carbonyls (more than two carbon atoms) showed also more contribution in the emission profile of the HFO fuel (26%) than in DF (22%).

Evaluation of miR-216a and miR-217 as Potential Biomarkers of Acute Exocrine Pancreatic Toxicity in Rats.

PubMed

Wang, Jianying; Huang, Wenhu; Thibault, Stephane; Brown, Thomas P; Bobrowski, Walter; Gukasyan, Hovhannes J; Evering, Winston; Hu, Wenyue; John-Baptiste, Annette; Vitsky, Allison

2017-02-01

Detecting and monitoring exocrine pancreatic damage during nonclinical and clinical testing is challenging because classical biomarkers amylase and lipase have limited sensitivity and specificity. Novel biomarkers for drug-induced pancreatic injury are needed to improve safety assessment and reduce late-stage attrition rates. In a series of studies, miR-216a and miR-217 were evaluated as potential biomarkers of acute exocrine pancreatic toxicity in rats. Our results revealed that miR-216a and miR-217 were almost exclusively expressed in rat pancreas and that circulating miR-216a and miR-217 were significantly increased in rats following administration of established exocrine pancreatic toxicants caerulein (CL) and 1-cyano-2-hydroxy-3-butene (CHB) as well as in rats administered a proprietary molecule known to primarily affect the exocrine pancreas. Conversely, neither microRNA was increased in rats administered a proprietary molecule known to cause a lesion at the pancreatic endocrine-exocrine interface (EEI) or in rats administered an established renal toxicant. Compared with amylase and lipase, increases in miR-216a and miR-217 were of greater magnitude, persisted longer, and/or correlated better with microscopic findings within the exocrine pancreas. Our findings demonstrate that in rats, miR-216a and miR-217 are sensitive and specific biomarkers of acute exocrine pancreatic toxicity that may add value to the measurement of classical pancreatic biomarkers.

Characterization of oxidized coal surfaces: Quarterly report, May 1987-July 1987

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hercules, D.M.

1987-01-01

Work has progressed in the areas of (1) exploration or derivatization reactions for ambient temperature in-situ derivatization of aldehydes, ketones, and phenols on carbon surfaces; (2) analysis of these derivatives by secondary ion mass spectrometry (SIMS) and laser mass spectrometry (LMS); (3) derivatization and analysis of a naturally weathered coal; (4) construction of a reactor for controlled low temperature oxidation of coal; and (5) design of a protocol for handling coal samples. Specific derivatization reactions studied in this period included reactions of Girard's reagent, 2,4-dinitrophenylhydrazine and bisulfite with aldehydes and ketones and 4-triethylammonium-2-butene (TAB), trimethylsilyl ethers (TMS) and dimethylsilyl ethersmore » (DMS) with phenols and alcohols. Positive ion SIMS analysis of Girard's reagent derivatives and TAB derivatives on a silver support yielded molecular ion species (e.g., cations from the salts) for a wide range of carbonyl and phenolic compounds, respectively. Comparison of negative ion LMS spectra of naturally weathered Illinois No. 6 coal before and after treatment with 2,4-dinitrophenylhydrazine reveals the presence of two high mass ions in the spectrum of treated coal that are not present in the spectra of either the untreated coal or the derivatizing reagent. This provides both evidence for carbonyl functionality on the surface of naturally weathered Illinois No. 6 coal and support for the feasibility of in-situ derivatization and analysis of organic components in the coal matrix. 5 refs.« less

Synthetic approach to the AB ring system of ouabain.

PubMed

Jung, Michael E; Piizzi, Grazia

2003-04-04

Several novel hydroxylated cis-decalin derivatives, potential intermediates for the synthesis of the AB ring system of the important cardiotonic steroid ouabain, have been synthesized from commercially available starting materials. The first step in the preparation of these highly functionalized intermediates is a Robinson annulation of the beta-keto ester 6 and the 4-silyl-3-buten-2-one 5 to furnish the octalone 4 with good diastereoselectivity in fair yield (due to competition with a novel silicon-to-carbon phenyl migration). Reduction of the epoxy alcohol 3 (derived from 4 in two high-yielding steps) with LiAlH(4) gave a mixture of the desired triol 11 along with the product of an unusual reductive opening at the tertiary carbon, namely the triol 12. A plausible mechanism for this unusual reduction is presented as are possible methods for avoiding it. In particular, reduction of the corrresponding epoxy ketone 15 with aluminum amalgam proceeded in good yield to give the hydroxy ketone 16. Also reduction of the epoxide ester having the inverted stereochemistry at C3 afforded the desired tertiary alcohol 33 in good yield. Another approach using the beta,gamma-unsaturated ketal 38 permitted the formation of the tertiary alcohol 40. Fleming oxidation of the related, very functionalized silane 39 afforded the desired 1beta-alcohol 41 in fair yield. Finally a novel rearrangement was observed when the epoxy alcohol 24 was treated with DIBAL to effect loss of the angular hydroxymethyl group to produce the tetrasubstitued alkene 29 in high yield.

Abundant Rodent Furan-Derived Urinary Metabolites Are Associated with Tobacco Smoke Exposure in Humans.

PubMed

Grill, Alex E; Schmitt, Thaddeus; Gates, Leah A; Lu, Ding; Bandyopadhyay, Dipankar; Yuan, Jian-Min; Murphy, Sharon E; Peterson, Lisa A

2015-07-20

Furan, a possible human carcinogen, is found in heat treated foods and tobacco smoke. Previous studies have shown that humans are capable of converting furan to its reactive metabolite, cis-2-butene-1,4-dial (BDA), and therefore may be susceptible to furan toxicity. Human risk assessment of furan exposure has been stymied because of the lack of mechanism-based exposure biomarkers. Therefore, a sensitive LC-MS/MS assay for six furan metabolites was applied to measure their levels in urine from furan-exposed rodents as well as in human urine from smokers and nonsmokers. The metabolites that result from direct reaction of BDA with lysine (BDA-N(α)-acetyllysine) and from cysteine-BDA-lysine cross-links (N-acetylcysteine-BDA-lysine, N-acetylcysteine-BDA-N(α)-acetyllysine, and their sulfoxides) were targeted in this study. Five of the six metabolites were identified in urine from rodents treated with furan by gavage. BDA-N(α)-acetyllysine, N-acetylcysteine-BDA-lysine, and its sulfoxide were detected in most human urine samples from three different groups. The levels of N-acetylcysteine-BDA-lysine sulfoxide were more than 10 times higher than that of the corresponding sulfide in many samples. The amount of this metabolite was higher in smokers relative to that in nonsmokers and was significantly reduced following smoking cessation. Our results indicate a strong relationship between BDA-derived metabolites and smoking. Future studies will determine if levels of these biomarkers are associated with adverse health effects in humans.

Are styrene oligomers in coastal sediments of an industrial area aryl hydrocarbon-receptor agonists?

PubMed

Hong, Seongjin; Lee, Junghyun; Lee, Changkeun; Yoon, Seo Joon; Jeon, Seungyeon; Kwon, Bong-Oh; Lee, Jong-Hyeon; Giesy, John P; Khim, Jong Seong

2016-06-01

Effect-directed analysis (EDA) was performed to identify the major aryl hydrocarbon receptor (AhR) agonists in sediments collected from a highly industrialized area (Lake Shihwa, Korea). Great AhR-mediated potencies were found in fractions containing aromatic compounds with log Kow values of 5-8, and relatively great concentrations of styrene oligomers (SOs) and polycyclic aromatic hydrocarbons (PAHs) were detected in those fractions. Until now, there was little information on occurrences and toxic relative potencies (RePs) of SOs in coastal environments. In the present study; i) distributions and compositions, ii) AhR binding affinities, and iii) contributions of SOs to total AhR-mediated potencies were determined in coastal sediments. Elevated concentrations of 10 SOs were detected in sediments of inland creeks ranging from 61 to 740 ng g(-1) dry mass (dm), while lesser concentrations were found in inner (mean = 33 ng g(-1) dm) and outer regions (mean = 25 ng g(-1) dm) of the lake. Concentrations of PAHs in sediments were comparable to those of SOs. 2,4-diphenyl-1-butene (SD3) was the predominant SO analogue in sediments. SOs and PAHs were accumulated in sediments near sources, and could not be transported to remote regions due to their hydrophobicity. RePs of 3 SOs could be derived, which were 1000- to 10,000-fold less than that of one representative potent AhR active PAH, benzo[a]pyrene. Although concentrations of SOs in sediments were comparable to those of PAHs, the collective contribution of SOs to total AhR-mediated potencies were rather small (<1%), primarily due to their smaller RePs. Overall, the present study provides information on distributions and AhR binding affinities for SOs as baseline data for degradation products of polystyrene plastic in the coastal environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Scaling Relations for Acidity and Reactivity of Zeolites

PubMed Central

2017-01-01

Zeolites are widely applied as solid acid catalysts in various technological processes. In this work we have computationally investigated how catalytic reactivity scales with acidity for a range of zeolites with different topologies and chemical compositions. We found that straightforward correlations are limited to zeolites with the same topology. The adsorption energies of bases such as carbon monoxide (CO), acetonitrile (CH3CN), ammonia (NH3), trimethylamine (N(CH3)3), and pyridine (C5H5N) give the same trend of acid strength for FAU zeolites with varying composition. Crystal orbital Hamilton populations (COHP) analysis provides a detailed molecular orbital picture of adsorbed base molecules on the Brønsted acid sites (BAS). Bonding is dominated by strong σ donation from guest molecules to the BAS for the adsorbed CO and CH3CN complexes. An electronic descriptor of acid strength is constructed based on the bond order calculations, which is an intrinsic parameter rather than adsorption energy that contains additional contributions due to secondary effects such as van der Waals interactions with the zeolite walls. The bond order parameter derived for the CH3CN adsorption complex represents a useful descriptor for the intrinsic acid strength of FAU zeolites. For FAU zeolites the activation energy for the conversion of π-adsorbed isobutene into alkoxy species correlates well with the acid strength determined by the NH3 adsorption energies. Other zeolites such as MFI and CHA do not follow the scaling relations obtained for FAU; we ascribe this to the different van der Waals interactions and steric effects induced by zeolite framework topology. PMID:29142616

Thermochemical and kinetic analyses on oxidation of isobutenyl radical and 2-hydroperoxymethyl-2-propenyl radical.

PubMed

Zheng, X L; Sun, H Y; Law, C K

2005-10-13

In recognition of the importance of the isobutene oxidation reaction in the preignition chemistry associated with engine knock, the thermochemistry, chemical reaction pathways, and reaction kinetics of the isobutenyl radical oxidation at low to intermediate temperature range were computationally studied, focusing on both the first and the second O2 addition to the isobutenyl radical. The geometries of reactants, important intermediates, transition states, and products in the isobutenyl radical oxidation system were optimized at the B3LYP/6-311G(d,p) and MP2(full)/6-31G(d) levels, and the thermochemical properties were determined on the basis of ab initio, density functional theory, and statistical mechanics. Enthalpies of formation for several important intermediates were calculated using isodesmic reactions at the DFT and the CBS-QB3 levels. The kinetic analysis of the first O2 addition to the isobutenyl radical was performed using enthalpies at the CBS-QB3 and G3(MP2) levels. The reaction forms a chemically activated isobutenyl peroxy adduct which can be stabilized, dissociate back to reactants, cyclize to cyclic peroxide-alkyl radicals, and isomerize to the 2-hydroperoxymethyl-2-propenyl radical that further undergoes another O2 addition. The reaction channels for isomerization and cyclization and further dissociation on this second O2 addition were analyzed using enthalpies at the DFT level with energy corrections based on similar reaction channels for the first O2 addition. The high-pressure limit rate constants for each reaction channel were determined as functions of temperature by the canonical transition state theory for further kinetic model development.

Rapid assessment of crystal orientation in semi-crystalline polymer films using rotational zone annealing and impact of orientation on mechanical properties

DOE PAGES

Ye, Changhuai; Wang, Chao; Wang, Jing; ...

2017-08-17

Crystal orientation in semi-crystalline polymers tends to enhance their performance, such as increased yield strength and modulus, along the orientation direction. Zone annealing (ZA) orients the crystal lamellae through a sharp temperature gradient that effectively directs the crystal growth, but the sweep rate (V ZA) of this gradient significantly impacts the extent of crystal orientation. Here in this work, we demonstrate rotational zone annealing (RZA) as an efficient method to elucidate the influence of V ZA on the crystal morphology of thin films in a single experiment using isotactic poly(1-butene), PB-1, as a model semi-crystalline polymer. These RZA results aremore » confirmed using standard, serial linear ZA to tune the structure from an almost unidirectional oriented morphology to weakly oriented spherulites. The overall crystallinity is only modestly changed in comparison to isothermal crystallization (maximum of 55% from ZA vs. 48% for isothermal crystallization). However, the average grain size increases and the spherulites become anisotropic from ZA. Due to these structural changes, the Young's modulus of the oriented films, both parallel and perpendicular to the spherulite orientation direction, is significantly increased by ZA. The modulus does become anisotropic after ZA due to the directionality in the crystal structure, with more than a threefold increase in the modulus parallel to the orientation direction for the highest oriented film in comparison to the modulus from isothermal crystallization. Lastly, RZA enables rapid identification of conditions to maximize orientation of crystals in thin polymer films, which could find utility in determining conditions to improve crystallinity and performance in organic electronics.« less

Characterization of gas station emissions during the CAREBeijing 2008 field study

NASA Astrophysics Data System (ADS)

Zheng, J.; Zhu, T.; Zhang, R.; Wang, M.; Chang, C.-C.; Shao, M.; Hu, M.

2011-05-01

A proton transfer-reaction mass spectrometer (PTR-MS) onboard a mobile laboratory was used to conduct emission measurements at eight gas stations in Beijing during the CAREBeijing 2008 campaign. Benzene, toluene, C8-, C9-aromatics, methanol, MTBE, butenes and pentenes were the major volatile organic compounds (VOCs) detected during the measurements. An inter-comparison between the PTR-MS and an on-line GC/MS/FID system was also conducted and the result showed good agreement between the two instruments (Interception < 0.08 ppbv, 0.72 < Slope < 0.95, and R2 > 0.92). A Gaussian point source plume model was applied to evaluate the VOCs emission rates. The results showed that on average about 4.5 mt of gasoline were emitted from gas stations in Beijing per day. The estimated emission factor (EF) for gas stations due to refueling processes was about 0.5 kg t-1, which was significantly lower than a value of 2.49 kg t-1 obtained in 2002, indicating a successful implementation of vapor recovery system in the gas stations of Beijing. On average, about 18 ppbv of benzene has been detected at one gas station, twice as much as the US Environmental Protection Agency (EPA) recommended safe chronic exposure level and implying a potential public health concern. MTBE and aromatics were found to be the major antiknocking additives used in gasoline supplied in Beijing. Our results reveal that emissions from gas stations represent an important source for VOCs in megacity Beijing and need to be properly included in emission inventories to assess their roles in photochemical ozone production and secondary organic aerosol formation. Furthermore, promoting methanol-blended fuel in Beijing can be an effective way to reduce toxic air pollutants emission.

Rapid assessment of crystal orientation in semi-crystalline polymer films using rotational zone annealing and impact of orientation on mechanical properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye, Changhuai; Wang, Chao; Wang, Jing

Crystal orientation in semi-crystalline polymers tends to enhance their performance, such as increased yield strength and modulus, along the orientation direction. Zone annealing (ZA) orients the crystal lamellae through a sharp temperature gradient that effectively directs the crystal growth, but the sweep rate (V ZA) of this gradient significantly impacts the extent of crystal orientation. Here in this work, we demonstrate rotational zone annealing (RZA) as an efficient method to elucidate the influence of V ZA on the crystal morphology of thin films in a single experiment using isotactic poly(1-butene), PB-1, as a model semi-crystalline polymer. These RZA results aremore » confirmed using standard, serial linear ZA to tune the structure from an almost unidirectional oriented morphology to weakly oriented spherulites. The overall crystallinity is only modestly changed in comparison to isothermal crystallization (maximum of 55% from ZA vs. 48% for isothermal crystallization). However, the average grain size increases and the spherulites become anisotropic from ZA. Due to these structural changes, the Young's modulus of the oriented films, both parallel and perpendicular to the spherulite orientation direction, is significantly increased by ZA. The modulus does become anisotropic after ZA due to the directionality in the crystal structure, with more than a threefold increase in the modulus parallel to the orientation direction for the highest oriented film in comparison to the modulus from isothermal crystallization. Lastly, RZA enables rapid identification of conditions to maximize orientation of crystals in thin polymer films, which could find utility in determining conditions to improve crystallinity and performance in organic electronics.« less

Metabolic Signature of Electrosurgical Liver Dissection

PubMed Central

von Schönfels, Witigo; von Kampen, Oliver; Patsenker, Eleonora; Stickel, Felix; Schniewind, Bodo; Hinz, Sebastian; Ahrens, Markus; Balschun, Katharina; Egberts, Jan-Hendrik; Richter, Klaus; Landrock, Andreas; Sipos, Bence; Will, Olga; Huebbe, Patrizia; Schreiber, Stefan; Nothnagel, Michael; Röcken, Christoph; Rimbach, Gerald; Becker, Thomas

2013-01-01

Background and Aims High frequency electrosurgery has a key role in the broadening application of liver surgery. Its molecular signature, i.e. the metabolites evolving from electrocauterization which may inhibit hepatic wound healing, have not been systematically studied. Methods Human liver samples were thus obtained during surgery before and after electrosurgical dissection and subjected to a two-stage metabolomic screening experiment (discovery sample: N = 18, replication sample: N = 20) using gas chromatography/mass spectrometry. Results In a set of 208 chemically defined metabolites, electrosurgical dissection lead to a distinct metabolic signature resulting in a separation in the first two dimensions of a principal components analysis. Six metabolites including glycolic acid, azelaic acid, 2-n-pentylfuran, dihydroactinidiolide, 2-butenal and n-pentanal were consistently increased after electrosurgery meeting the discovery (p<2.0×10−4) and the replication thresholds (p<3.5×10−3). Azelaic acid, a lipid peroxidation product from the fragmentation of abundant sn-2 linoleoyl residues, was most abundant and increased 8.1-fold after electrosurgical liver dissection (preplication = 1.6×10−4). The corresponding phospholipid hexadecyl azelaoyl glycerophosphocholine inhibited wound healing and tissue remodelling in scratch- and proliferation assays of hepatic stellate cells and cholangiocytes, and caused apoptosis dose-dependently in vitro, which may explain in part the tissue damage due to electrosurgery. Conclusion Hepatic electrosurgery generates a metabolic signature with characteristic lipid peroxidation products. Among these, azelaic acid shows a dose-dependent toxicity in liver cells and inhibits wound healing. These observations potentially pave the way for pharmacological intervention prior liver surgery to modify the metabolic response and prevent postoperative complications. PMID:24058442

Characterization of environmental chemicals with potential for DNA damage using isogenic DNA repair-deficient chicken DT40 cell lines.

PubMed

Yamamoto, Kimiyo N; Hirota, Kouji; Kono, Koichi; Takeda, Shunichi; Sakamuru, Srilatha; Xia, Menghang; Huang, Ruili; Austin, Christopher P; Witt, Kristine L; Tice, Raymond R

2011-08-01

Included among the quantitative high throughput screens (qHTS) conducted in support of the US Tox21 program are those being evaluated for the detection of genotoxic compounds. One such screen is based on the induction of increased cytotoxicity in seven isogenic chicken DT40 cell lines deficient in DNA repair pathways compared to the parental DNA repair-proficient cell line. To characterize the utility of this approach for detecting genotoxic compounds and identifying the type(s) of DNA damage induced, we evaluated nine of 42 compounds identified as positive for differential cytotoxicity in qHTS (actinomycin D, adriamycin, alachlor, benzotrichloride, diglycidyl resorcinol ether, lovastatin, melphalan, trans-1,4-dichloro-2-butene, tris(2,3-epoxypropyl)isocyanurate) and one non-cytotoxic genotoxic compound (2-aminothiamine) for (1) clastogenicity in mutant and wild-type cells; (2) the comparative induction of γH2AX positive foci by melphalan; (3) the extent to which a 72-hr exposure duration increased assay sensitivity or specificity; (4) the use of 10 additional DT40 DNA repair-deficient cell lines to better analyze the type(s) of DNA damage induced; and (5) the involvement of reactive oxygen species in the induction of DNA damage. All compounds but lovastatin and 2-aminothiamine were more clastogenic in at least one DNA repair-deficient cell line than the wild-type cells. The differential responses across the various DNA repair-deficient cell lines provided information on the type(s) of DNA damage induced. The results demonstrate the utility of this DT40 screen for detecting genotoxic compounds, for characterizing the nature of the DNA damage, and potentially for analyzing mechanisms of mutagenesis. Copyright © 2011 Wiley-Liss, Inc.

Characterization of environmental chemicals with potential for DNA damage using isogenic DNA repair-deficient chicken DT40 cell lines

PubMed Central

Yamamoto, Kimiyo N.; Hirota, Kouji; Kono, Koichi; Takeda, Shunichi; Sakamuru, Srilatha; Xia, Menghang; Huang, Ruili; Austin, Christopher P.; Witt, Kristine L.; Tice, Raymond R.

2012-01-01

Included among the quantitative high throughput screens (qHTS) conducted in support of the U.S. Tox21 program are those being evaluated for the detection of genotoxic compounds. One such screen is based on the induction of increased cytotoxicity in 7 isogenic chicken DT40 cell lines deficient in DNA repair pathways compared to the parental DNA repair-proficient cell line. To characterize the utility of this approach for detecting genotoxic compounds and identifying the type(s) of DNA damage induced, we evaluated nine of 42 compounds identified as positive for differential cytotoxicity in qHTS (actinomycin D, adriamycin, alachlor, benzotrichloride, diglycidyl resorcinol ether, lovastatin, melphalan, trans-1,4-dichloro-2-butene, tris(2,3-epoxypropyl)isocyanurate) and one non-cytotoxic genotoxic compound (2-aminothiamine) for (1) clastogenicity in mutant and wild-type cells; (2) the comparative induction of γH2AX positive foci by melphalan; (3) the extent to which a 72-hr exposure duration increased assay sensitivity or specificity; (4) the use of 10 additional DT40 DNA repair-deficient cell lines to better analyze the type(s) of DNA damage induced; and (5) the involvement of reactive oxygen species in the induction of DNA damage. All compounds but lovastatin and 2-aminothiamine were more clastogenic in at least one DNA repair-deficient cell line than the wild-type cells. The differential responses across the various DNA repair-deficient cell lines provided information on the type(s) of DNA damage induced. The results demonstrate the utility of this DT40 screen for detecting genotoxic compounds, for characterizing the nature of the DNA damage, and potentially for analyzing mechanisms of mutagenesis. PMID:21538559

Biochemical Characterization and Homology Modeling of Methylbutenol Synthase and Implications for Understanding Hemiterpene Synthase Evolution in Plants*

PubMed Central

Gray, Dennis W.; Breneman, Steven R.; Topper, Lauren A.; Sharkey, Thomas D.

2011-01-01

2-Methyl-3-buten-2-ol (MBO) is a five-carbon alcohol produced and emitted in large quantities by many species of pine native to western North America. MBO is structurally and biosynthetically related to isoprene and can have an important impact on regional atmospheric chemistry. The gene for MBO synthase was identified from Pinus sabiniana, and the protein encoded was functionally characterized. MBO synthase is a bifunctional enzyme that produces both MBO and isoprene in a ratio of ∼90:1. Divalent cations are required for activity, whereas monovalent cations are not. MBO production is enhanced by K+, whereas isoprene production is inhibited by K+ such that, at physiologically relevant [K+], little or no isoprene emission should be detected from MBO-emitting trees. The Km of MBO synthase for dimethylallyl diphosphate (20 mm) is comparable with that observed for angiosperm isoprene synthases and 3 orders of magnitude higher than that observed for monoterpene and sesquiterpene synthases. Phylogenetic analysis showed that MBO synthase falls into the TPS-d1 group (gymnosperm monoterpene synthases) and is most closely related to linalool synthase from Picea abies. Structural modeling showed that up to three phenylalanine residues restrict the size of the active site and may be responsible for making this a hemiterpene synthase rather than a monoterpene synthase. One of these residues is homologous to a Phe residue found in the active site of isoprene synthases. The remaining two Phe residues do not have homologs in isoprene synthases but occupy the same space as a second Phe residue that closes off the isoprene synthase active site. PMID:21504898

Detection of butane gas inhalation at 16days after hypoxic encephalopathy: A case report.

PubMed

Sato, Takako; Nishioka, Hiroshi; Tsuboi, Kento; Katagi, Munehiro; Miki, Akihiro; Saito, Takashi; Abe, Shuntaro; Nomura, Masakatsu; Kitagawa, Misa; Tsuchihashi, Hitoshi; Suzuki, Koichi

2017-11-01

In Japan, there are increasing reports of death by poisoning following butane abuse. To determine the specific cause of death in such cases, it is important to confirm the presence of fuel gas components in the body, although careful analysis is required because of their volatile properties. In most reported cases, the subject died suddenly during or immediately after butane aspiration. Thus, the butane concentration in the samples from the deceased should be relatively high. Herein, we present a case of an 18-year-old man found with cardiopulmonary arrest, who then exhibited hypoxic encephalopathy for 16days in a hospital. At autopsy, we detected hypoxic encephalopathy, pneumonia, and ischemia-reperfusion injury of the myocardium, while the cause of cardiac arrest remained unclear. Toxicological analysis was then performed for fuel gas components in several specimens collected at autopsy. Results showed that n-butane and isobutane were detected in the adipose tissue at 16days after inhalation, indicating a role of butane gas inhalation as the cause of death. These data suggest that adipose tissue may be the most appropriate analysis sample to be collected at postmortem in cases where involvement of volatile and fat-soluble gas inhalation is suspected. Copyright © 2017 Elsevier B.V. All rights reserved.

SAMPEX science pointing with velocity avoidance. [solar anomalous and magnetospheric particle explorer

NASA Technical Reports Server (NTRS)

Frakes, Joseph P.; Henretty, Debra A.; Flatley, Thomas W.; Markley, F. L.; San, Josephine K.; Lightsey, E. G.

1992-01-01

The Solar, Anomalous, and Magnetospheric Particle Explorer (SAMPEX) science pointing mode is presented with the additional constraint of velocity avoidance. This constraint has been added in light of the orbital debris and micrometeoroid fluxes that have been revealed by the Long Duration Exposure Facility (LDEF) recovered in January 1990. These fluxes are 50-100 times higher than the flux tables that were used in the September 1988 proposal to NASA for the SAMPEX mission. The SAMPEX Heavey Ion Large Telescope (HILT) sensor includes a flow-through isobutane proportional counter that is susceptible to penetration by orbital debris and micrometeoroids. Thus, keeping the HILT sensor pointed away from the velocity vector, the direction of maximum flux, will compensate for the higher than expected fluxes. Using an orbital debris model and a micrometeoroid model developed at the Johnson Space Center (JSC), and a SAMPEX dynamic simulator developed by the Guidance and Control Branch at the Goddard Space Flight Center (GSFC), an 'optimal' minimum ram angle (the angle between the HILT boresight and the velocity vector) of 90 degrees has been determined. It is optimal in the sense of minimizing the science pointing performance degradation while providing approximately an 89 percent chance of survival for the HILT sensor over a three year period.

Monitoring and Control of an Adsorption System Using Electrical Properties of the Adsorbent for Organic Compound Abatement.

PubMed

Hu, Ming-Ming; Emamipour, Hamidreza; Johnsen, David L; Rood, Mark J; Song, Linhua; Zhang, Zailong

2017-07-05

Adsorption systems typically need gas and temperature sensors to monitor their adsorption/regeneration cycles to separate gases from gas streams. Activated carbon fiber cloth (ACFC)-electrothermal swing adsorption (ESA) is an adsorption system that has the potential to be controlled with the electrical properties of the adsorbent and is studied here to monitor and control the adsorption/regeneration cycles without the use of gas and temperature sensors and to predict breakthrough before it occurs. The ACFC's electrical resistance was characterized on the basis of the amount of adsorbed organic gas/vapor and the adsorbent temperature. These relationships were then used to develop control logic to monitor and control ESA cycles on the basis of measured resistance and applied power values. Continuous sets of adsorption and regeneration cycles were performed sequentially entirely on the basis of remote electrical measurements and achieved ≥95% capture efficiency at inlet concentrations of 2000 and 4000 ppm v for isobutane, acetone, and toluene in dry and elevated relative humidity gas streams, demonstrating a novel cyclic ESA system that does not require gas or temperature sensors. This contribution is important because it reduces the cost and simplifies the system, predicts breakthrough before its occurrence, and reduces emissions to the atmosphere.

Apparatus of the Vapor-pressure Measurements for Natural Refrigerants

NASA Astrophysics Data System (ADS)

Higuchi, Satoru; Higashi, Yukihiro

An apparatus for measuring the vapor-pressures was newly designed and constructed in order to make the basic thermodynamic properties for environmentally acceptable refrigerants clear. The temperature of sample fluid was measured with 100Ω platinum resistance thermometer calibrated against ITS-90 using a 25Ω standard platinum resistance thermometer. With respect to the pressure measurement, two kinds of presure transducer were adopted. One is a diaphragm semi-conductor strain pressure transducer with the uncertainty of ±0.09%. This pressure transducer was calibrated against quartz crystal pressure transducer with the uncertainty of ±0.01% after every series of experiments. Another is a quartz crystal pressure transducer with the uncertainty of ±0.01%. A quartz crystal pressure transducer was calibrated against the dead weight pressure gauge and barometer. The vapor-pressures for R-32, R-134a, R-290 (propane), R-600a (iso-butane) and n-pentane were measured in the temperature range between273.15 and 323.15K. As the results of vapor-pressure measurements, the reliability of the experimental apparatus as well as the reproducibility of the experimental data were confirmed. In addition, coefficients of Antoine vapor pressure equation were determined from the experimental data. Normal boiling points for environmentally acceptable refrigerants were also determined with high accuracy.

Identification of potent odourants in wine and brewed coffee using gas chromatography-olfactometry and comprehensive two-dimensional gas chromatography.

PubMed

Chin, Sung-Tong; Eyres, Graham T; Marriott, Philip J

2011-10-21

Volatile constituents in wine and brewed coffee were analyzed using a combined system incorporating both GC-olfactometry (GC-O) and comprehensive two-dimensional GC-flame ionization detection (GC×GC-FID). A column set consisting of a 15m first dimension ((1)D; DB-FFAP (free fatty acid phase)), and a 1.0m (2)D column (DB-5 phase) was applied to achieve the GC×GC separation of the volatile extracts isolated by using solid phase extraction (SPE). While 1D GC resulted in many overlapping peaks, GC×GC allowed resolution of co-eluting compounds which coincided with the odour region located using GC-O. Character-impact odourants were tentatively identified through data correlation of GC×GC contour plots across results obtained using either time-of-flight mass spectrometry (TOFMS), or with flame photometric detection (FPD) for sulfur speciation. The odourants 2-methyl-2-butenal, 2-(methoxymethyl)-furan, dimethyl trisulfide, 2-ethyl-5-methyl-pyrazine, 2-octenal, 2-furancarboxaldehyde, 3-mercapto-3-methyl-1-butanol, 2-methoxy-3-(2-methylpropyl)-pyrazine, 2-furanmethanol and isovaleric acid were suspected to be particularly responsible for coffee aroma using this approach. The presented methodology was applied to identify the potent odourants in two different Australian wine varietals. 1-Octen-3-ol, butanoic acid and 2-methylbutanoic acid were detected in both Merlot and a Sauvignon Blanc+Semillon (SV) blend with high aroma potency. Several co-eluting peaks of ethyl 4-oxo-pentanoate, 3,7-dimethyl-1,5,7-octatrien-3-ol, (Z)-2-octen-1-ol, 5-hydroxy-2-methyl-1,3-dioxane were likely contributors to the Merlot wine aroma; while (Z)-3-hexen-1-ol, β-phenylethyl acetate, hexanoic acid and co-eluting peaks of 3-ethoxy-1-propanol and hexyl formate may contribute to SV wine aroma character. The volatile sulfur compound 2-mercapto-ethyl acetate was believed to contribute a fruity, brothy, meaty, sulfur odour to Australian Merlot and SV wines. Copyright © 2011 Elsevier B.V. All rights reserved.

Development and Characterization of a Green Fluorescent Protein-Based Bacterial Biosensor for Bioavailable Toluene and Related Compounds†

PubMed Central

Stiner, Lawrence; Halverson, Larry J.

2002-01-01

A green fluorescent protein-based Pseudomonas fluorescens strain A506 biosensor was constructed and characterized for its potential to measure benzene, toluene, ethylbenzene, and related compounds in aqueous solutions. The biosensor is based on a plasmid carrying the toluene-benzene utilization (tbu) pathway transcriptional activator TbuT from Ralstonia pickettii PKO1 and a transcriptional fusion of its promoter PtbuA1 with a promoterless gfp gene on a broad-host-range promoter probe vector. TbuT was not limiting, since it was constitutively expressed by being fused to the neomycin phosphotransferase (nptII) promoter. The biosensor cells were readily induced, and fluorescence emission after induction periods of 3 h correlated well with toluene, benzene, ethylbenzene, and trichloroethylene concentrations. Our experiments using flow cytometry show that intermediate levels of gfp expression in response to toluene reflect uniform induction of cells. As the toluene concentration increases, the level of gfp expression per cell increases until saturation kinetics of the TbuT-PtbuA1 system are observed. Each inducer had a unique minimum concentration that was necessary for induction, with Kapp values that ranged from 3.3 ± 1.8 μM for toluene to 35.6 ± 16.6 μM for trichloroethylene (means ± standard errors of the means), and maximal fluorescence response. The fluorescence response was specific for alkyl-substituted benzene derivatives and branched alkenes (di- and trichloroethylene, 2-methyl-2-butene). The biosensor responded in an additive fashion to the presence of multiple inducers and was unaffected by the presence of compounds that were not inducers, such as those present in gasoline. Flow cytometry revealed that, in response to toxic concentrations of gasoline, there was a small uninduced population and another larger fully induced population whose levels of fluorescence corresponded to the amount of effectors present in the sample. These results demonstrate the potential for green fluorescent protein-based bacterial biosensors to measure environmental contaminants. PMID:11916719

Development of a µ-TPC detector as a standard instrument for low-energy neutron field characterisation.

PubMed

Maire, D; Billard, J; Bosson, G; Bourrion, O; Guillaudin, O; Lamblin, J; Lebreton, L; Mayet, F; Médard, J; Muraz, J F; Richer, J P; Riffard, Q; Santos, D

2014-10-01

In order to measure the energy and fluence of neutron fields, in the energy range of 8 to 1 MeV, a new primary standard is being developed at the Institute for Radioprotection and Nuclear Safety (IRSN). This project, Micro Time Projection Chamber (µ-TPC), carried out in collaboration with the Laboratoire de Physqique Subatomique et de Cosmologie (LPSC), is based on the nucleus recoil detector principle. The measurement strategy requires track reconstruction of recoiling nuclei down to a few kiloelectronvolts, which can be achieved using a micro-pattern gaseous detector. A gas mixture, mainly isobutane, is used as an n-p converter to detect neutrons within the detection volume. Then electrons, coming from the ionisation of the gas by the proton recoil, are collected by the pixelised anode (2D projection). A self-triggered electronics system is able to perform the anode readout at a 50-MHz frequency in order to give the third dimension of the track. Then, the scattering angle is deduced from this track using algorithms. The charge collection leads to the proton energy, taking into account the ionisation quenching factor. This article emphasises the neutron energy measurements of a monoenergetic neutron field produced at 127 keV. The fluence measurement is not shown in this article. The measurements are compared with Monte Carlo simulations using realistic neutron fields and simulations of the detector response. The discrepancy between experiments and simulations is 5 keV mainly due to the calibration uncertainties of 10 %. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

A Generalized Fluid System Simulation Program to Model Flow Distribution in Fluid Networks

NASA Technical Reports Server (NTRS)

Majumdar, Alok; Bailey, John W.; Schallhorn, Paul; Steadman, Todd

1998-01-01

This paper describes a general purpose computer program for analyzing steady state and transient flow in a complex network. The program is capable of modeling phase changes, compressibility, mixture thermodynamics and external body forces such as gravity and centrifugal. The program's preprocessor allows the user to interactively develop a fluid network simulation consisting of nodes and branches. Mass, energy and specie conservation equations are solved at the nodes; the momentum conservation equations are solved in the branches. The program contains subroutines for computing "real fluid" thermodynamic and thermophysical properties for 33 fluids. The fluids are: helium, methane, neon, nitrogen, carbon monoxide, oxygen, argon, carbon dioxide, fluorine, hydrogen, parahydrogen, water, kerosene (RP-1), isobutane, butane, deuterium, ethane, ethylene, hydrogen sulfide, krypton, propane, xenon, R-11, R-12, R-22, R-32, R-123, R-124, R-125, R-134A, R-152A, nitrogen trifluoride and ammonia. The program also provides the options of using any incompressible fluid with constant density and viscosity or ideal gas. Seventeen different resistance/source options are provided for modeling momentum sources or sinks in the branches. These options include: pipe flow, flow through a restriction, non-circular duct, pipe flow with entrance and/or exit losses, thin sharp orifice, thick orifice, square edge reduction, square edge expansion, rotating annular duct, rotating radial duct, labyrinth seal, parallel plates, common fittings and valves, pump characteristics, pump power, valve with a given loss coefficient, and a Joule-Thompson device. The system of equations describing the fluid network is solved by a hybrid numerical method that is a combination of the Newton-Raphson and successive substitution methods. This paper also illustrates the application and verification of the code by comparison with Hardy Cross method for steady state flow and analytical solution for unsteady flow.

Theoretical chemical kinetic study of the H-atom abstraction reactions from aldehydes and acids by Ḣ atoms and ȮH, HȮ2, and ĊH3 radicals.

PubMed

Mendes, Jorge; Zhou, Chong-Wen; Curran, Henry J

2014-12-26

We have performed a systematic, theoretical chemical kinetic investigation of H atom abstraction by Ḣ atoms and ȮH, HȮ2, and ĊH3 radicals from aldehydes (methanal, ethanal, propanal, and isobutanal) and acids (methanoic acid, ethanoic acid, propanoic acid, and isobutanoic acid). The geometry optimizations and frequencies of all of the species in the reaction mechanisms of the title reactions were calculated using the MP2 method and the 6-311G(d,p) basis set. The one-dimensional hindered rotor treatment for reactants and transition states and the intrinsic reaction coordinate calculations were also determined at the MP2/6-311G(d,p) level of theory. For the reactions of methanal and methanoic acid with Ḣ atoms and ȮH, HȮ2, and ĊH3 radicals, the calculated relative electronic energies were obtained with the CCSD(T)/cc-pVXZ (where X = D, T, and Q) method and were extrapolated to the complete basis set limit. The electronic energies obtained with the CCSD(T)/cc-pVTZ method were benchmarked against the CCSD(T)/CBS energies and were found to be within 1 kcal mol(-1) of one another. Thus, the energies calculated using the less expensive CCSD(T)/cc-pVTZ method were used in all of the reaction mechanisms and in calculating our high-pressure limit rate constants for the title reactions. Rate constants were calculated using conventional transition state theory with an asymmetric Eckart tunneling correction, as implemented in Variflex. Herein, we report the individual and average rate constants, on a per H atom basis, and total rate constants in the temperature range 500-2000 K. We have compared some of our rate constant results to available experimental and theoretical data, and our results are generally in good agreement.

The Unimolecular Reactions of CF3CHF2 Studied by Chemical Activation: Assignment of Rate Constants and Threshold Energies to the 1,2-H Atom Transfer, 1,1-HF and 1,2-HF Elimination Reactions, and the Dependence of Threshold Energies on the Number of F-Atom Substituents in the Fluoroethane Molecules.

PubMed

Smith, Caleb A; Gillespie, Blanton R; Heard, George L; Setser, D W; Holmes, Bert E

2017-11-22

The recombination of CF 3 and CHF 2 radicals in a room-temperature bath gas was used to prepare vibrationally excited CF 3 CHF 2 * molecules with 101 kcal mol -1 of vibrational energy. The subsequent 1,2-H atom transfer and 1,1-HF and 1,2-HF elimination reactions were observed as a function of bath gas pressure by following the CHF 3 , CF 3 (F)C: and C 2 F 4 product concentrations by gas chromatography using a mass spectrometer as the detector. The singlet CF 3 (F)C: concentration was measured by trapping the carbene with trans-2-butene. The experimental rate constants are 3.6 × 10 4 , 4.7 × 10 4 , and 1.1 × 10 4 s -1 for the 1,2-H atom transfer and 1,1-HF and 1,2-HF elimination reactions, respectively. These experimental rate constants were matched to statistical RRKM calculated rate constants to assign threshold energies (E 0 ) of 88 ± 2, 88 ± 2, and 87 ± 2 kcal mol -1 to the three reactions. Pentafluoroethane is the only fluoroethane that has a competitive H atom transfer decomposition reaction, and it is the only example with 1,1-HF elimination being more important than 1,2-HF elimination. The trend of increasing threshold energies for both 1,1-HF and 1,2-HF processes with the number of F atoms in the fluoroethane molecule is summarized and investigated with electronic-structure calculations. Examination of the intrinsic reaction coordinate associated with the 1,1-HF elimination reaction found an adduct between CF 3 (F)C: and HF in the exit channel with a dissociation energy of ∼5 kcal mol -1 . Hydrogen-bonded complexes between HF and the H atom migration transition state of CH 3 (F)C: and the F atom migration transition state of CF 3 (F)C: also were found by the calculations. The role that these carbene-HF complexes could play in 1,1-HF elimination reactions is discussed.

Identification of an antibacterial compound, benzylideneacetone, from Xenorhabdus nematophila against major plant-pathogenic bacteria.

PubMed

Ji, Dongjin; Yi, Youngkeun; Kang, Ga-Hwa; Choi, Yong-Hwa; Kim, Pankyung; Baek, Nam-In; Kim, Yonggyun

2004-10-15

An entomopathogenic bacterium, Xenorhabdus nematophila, is known to have potent antibiotic activities to maintain monoxenic condition in its insect host for effective pathogenesis and ultimately for optimal development of its nematode symbiont, Steinernema carpocapsae. In this study we assess its antibacterial activity against plant-pathogenic bacteria and identify its unknown antibiotics. The bacterial culture broth had significant antibacterial activity that increased with development of the bacteria and reached its maximum at the stationary growth phase. The antibiotic activities were significant against five plant-pathogenic bacterial strains: Agrobacterium vitis, Pectobacterium carotovorum subsp. atrosepticum, P. carotovorum subsp. carotovorum, Pseudomonas syringae pv. tabaci, and Ralstonia solanacearum. The antibacterial factors were extracted with butanol and fractionated using column chromatography with the eluents of different hydrophobic intensities. Two active antibacterial subfractions were purified, and the higher active fraction was further fractionated and identified as a single compound of benzylideneacetone (trans-4-phenyl-3-buten-2-one). With heat stability, the synthetic compound showed equivalent antibiotic activity and spectrum to the purified compound. This study reports a new antibiotic compound synthesized by X. nematophila, which is a monoterpenoid compound and active against some Gram-negative bacteria.

Improvement of a respiratory ozone analyzer.

PubMed

Ultman, J S; Ben-Jebria, A; Mac Dougall, C S; Rigas, M L

1997-10-01

The breath-to-breath measurement of total respiratory ozone (O3) uptake requires monitoring O3 concentration at the airway opening with an instrument that responds rapidly relative to the breathing frequency. Our original chemiluminescent analyzer, using 2-methyl-2-butene as the reactant gas, had a 10% to 90% step-response time of 110 msec and a minimal detectable concentration of 0.018 parts per million (ppm) O3 (Ben-Jebria et al. 1990). This instrument was suitable for respiratory O3 monitoring during quiet breathing and light exercise. For this study, we constructed a more self-contained analyzer with a faster response time using ethylene as the reactant gas. When the analyzer was operated at a reaction chamber pressure of 350 torr, an ethylene-to-sample flow ratio of 4:1, and a sampling flow of 0.6 liters per minute (Lpm), it had a 10% to 90% step-response time of 70 msec and a minimal detectable concentration of 0.006 ppm. These specifications make respiratory O3 monitoring possible during moderate-to-heavy exercise. In addition, the nonlinear calibration and the carbon dioxide (CO2) interference exhibited by the original analyzer were eliminated. In breath-to-breath measurements in two healthy men, the fractional uptake of O3 during one minute of quiet breathing was comparable to the results obtained by using a slowly responding commercial analyzer with a quasi-steady material balance method (Wiester et al. 1996). In fact, fractional uptake was about 0.8 regardless of O3 exposure concentration (0.11 to 0.43 ppm) or ventilation rate (4 to 41 Lpm/m2).

High-temperature oxidation chemistry of n-butanol--experiments in low-pressure premixed flames and detailed kinetic modeling.

PubMed

Hansen, N; Harper, M R; Green, W H

2011-12-07

An automated reaction mechanism generator is used to develop a predictive, comprehensive reaction mechanism for the high-temperature oxidation chemistry of n-butanol. This new kinetic model is an advancement of an earlier model, which had been extensively tested against earlier experimental data (Harper et al., Combust. Flame, 2011, 158, 16-41). In this study, the model's predictive capabilities are improved by targeting isomer-resolved quantitative mole fraction profiles of flame species in low-pressure flames. To this end, a total of three burner-stabilized premixed flames are isomer-selectively analyzed by flame-sampling molecular-beam time-of-flight mass spectrometry using photoionization by tunable vacuum-ultraviolet synchrotron radiation. For most species, the newly developed chemical kinetic model is capable of accurately reproducing the experimental trends in these flames. The results clearly indicate that n-butanol is mainly consumed by H-atom abstraction with H, O, and OH, forming predominantly the α-C(4)H(9)O radical (CH(3)CH(2)CH(2)˙CHOH). Fission of C-C bonds in n-butanol is only predicted to be significant in a similar, but hotter flame studied by Oßwald et al. (Combust. Flame, 2011, 158, 2-15). The water-elimination reaction to 1-butene is found to be of no importance under the premixed conditions studied here. The initially formed isomeric C(4)H(9)O radicals are predicted to further oxidize by reacting with H and O(2) or to decompose to smaller fragments via β-scission. Enols are detected experimentally, with their importance being overpredicted by the model.

Production of Low-Freezing-Point Highly Branched Alkanes through Michael Addition.

PubMed

Jing, Yaxuan; Xia, Qineng; Liu, Xiaohui; Wang, Yanqin

2017-12-22

A new approach for the production of low-freezing-point, high-quality fuels from lignocellulose-derived molecules was developed with Michael addition as the key step. Among the investigated catalysts, CoCl 2 ⋅6 H 2 O was found most active for the Michael addition of 2,4-pentanedione with FA (single aldol adduct of furfural and acetone, 4-(2-furanyl)-3-butene-2-one). Over CoCl 2 ⋅6 H 2 O, a high carbon yield of C 13 oxygenates (about 75 %) can be achieved under mild conditions (353 K, 20 h). After hydrodeoxygenation, low-freezing-point (<223 K) branched alkanes with 13 carbons within jet fuel ranges were obtained over a Pd/NbOPO 4 catalyst. Furthermore, C 18,23 fuel precursors could be easily synthesized through Michael addition of 2,4-pentanedione with DFA (double-condensation product of furfural and acetone) under mild conditions and the molar ratio of C 18 /C 23 is dependent on the reaction conditions of Michael addition. After hydrodeoxygenation, high density (0.8415 g mL -1 ) and low-freezing-point (<223 K) branched alkanes with 18, 23 carbons within lubricant range were also obtained over a Pd/NbOPO 4 catalyst. These highly branched alkanes can be directly used as transportation fuels or additives. This work opens a new strategy for the synthesis of highly branched alkanes with low freezing point from renewable biomass. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Formation and chemical reactivity of carbon fibers prepared by defluorination of graphite fluoride

NASA Technical Reports Server (NTRS)

Hung, Ching-Cheh

1994-01-01

Defluorination of graphite fluoride (CFX) by heating to temperatures of 250 to 450 C in chemically reactive environments was studied. This is a new and possibly inexpensive process to produce new carbon-based materials. For example, CF 0.68 fibers, made from P-100 carbon fibers, can be defluorinated in BrH2C-CH = CH-CH2Br (1,4-dibromo-2butene) heated to 370 C, and graphitized to produce fibers with an unusually high modulus and a graphite layer structure that is healed and cross-linked. Conversely, a sulfur-doped, visibly soft carbon fiber was produced by defluorinating CF 0.9 fibers, made from P-25, in sulfur (S) vapor at 370 C and then heating to 660 C in nitrogen (N2). Furthermore, defluorination of the CF 0.68 fibers in bromine (Br2) produced fragile, structurally damaged carbon fibers. Heating these fragile fibers to 1100 C in N2 caused further structural damage, whereas heating to 150 C in bromoform (CHBr3) and then to 1100 C in N2 healed the structural defects. The defluorination product of CFX, tentatively called activated graphite, has the composition and molecular structure of graphite, but is chemically more reactive. Activated graphite is a scavenger of manganese (Mn), and can be intercalated with magnesium (Mg). Also, it can easily collect large amounts of an alloy made from copper (Cu) and type 304 stainless steel to form a composite. Finally, there are indications that activated graphite can wet metals or ceramics, thereby forming stronger composites with them than the pristine carbon fibers can form.

Undisturbed and disturbed above canopy ponderosa pine emissions: PTR-TOF-MS measurements and MEGAN 2.1 model results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaser, L.; Karl, T.; Guenther, A.

2013-01-01

We present the first eddy covariance flux measurements of volatile organic compounds (VOCs) using a proton-transfer-reaction time-of-flight mass-spectrometer (PTR-TOFMS) above a ponderosa pine forest in Colorado, USA. The high mass resolution of the PTR-TOF-MS enabled the identification of chemical sum formulas. During a 30 day measurement period in August and September 2010, 649 different ion mass peaks were detected in the ambient air mass spectrum (including primary ions and mass calibration ompounds). Eddy covariance with the vertical wind speed was calculated for all ion mass peaks. On a typical day, 17 ion mass peaks including protonated parent compounds, their fragmentsmore » and isotopes as well as VOC-H+-water clusters showed a significant flux with daytime average emissions above a reliable flux threshold of 0.1mgcompoundm-2 h-1. These ion mass peaks could be assigned to seven compound classes. The main flux contributions during daytime (10:00-18:00 LT) are attributed to the sum of 2-methyl-3-buten-2-ol (MBO) and isoprene (50 %), methanol (12%), the sum of acetic acid and glycolaldehyde (10%) and the sum of monoterpenes (10 %). The total MBO+isoprene flux was composed of 10% isoprene and 90% MBO. There was good agreement between the light and temperature dependency of the sum of MBO and isoprene observed for this work and those of earlier studies. The above canopy flux measurements of the sum of MBO and isoprene and the sum of 20 monoterpenes were compared to emissions calculated using the Model of Emissions of Gases and Aerosols from Nature (MEGAN 2.1). The best agreement between MEGAN 2.1 and measurements was reached using emission factors determined from site specific leaf cuvette measurements. While the modelled and measured MBO+isoprene fluxes agree well the emissions of the sum of monoterpenes is underestimated by MEGAN 2.1. This is expected as some factors impacting monoterpene emissions, such as physical damage of needles and branches due to storms, are not included in MEGAN 2.1.« less

OH Radical Reaction Rate Coefficients, Infrared Spectrum, and Global Warming Potential of (CF3)2CFCH═CHF (HFO-1438ezy(E)).

PubMed

Papadimitriou, Vassileios C; Burkholder, James B

2016-08-25

Rate coefficients, k(T), for the OH radical + (E)-(CF3)2CFCH═CHF ((E)-1,3,4,4,4-pentafluoro-3-(trifluoromethyl)-1-butene, HFO-1438ezy(E)) gas-phase reaction were measured using pulsed laser photolysis-laser-induced fluorescence (PLP-LIF) between 214 and 380 K and 50 and 450 Torr (He or N2 bath gas) and with a relative rate method at 296 K between 100 and 400 Torr (synthetic air). Over the range of pressures included in this study, no pressure dependence in k(T) was observed. k(296 K) obtained using the two techniques agreed to within ∼3% with (3.26 ± 0.26) × 10(-13) cm(3) molecule(-1) s(-1) (2σ absolute uncertainty) obtained using the PLP-LIF technique. k(T) displayed non-Arrhenius behavior that is reproduced by (7.34 ± 0.30) × 10(-19)T(2) exp[(481 ± 10)/T) cm(3) molecule(-1) s(-1). With respect to OH reactive loss, the atmospheric lifetime of HFO-1438ezy(E) is estimated to be ∼36 days and HFO-1438ezy(E) is considered a very short-lived substance (VSLS) (the actual lifetime will depend on the time and location of the HFO-1438ezy(E) emission). On the basis of the HFO-1438ezy(E) infrared absorption spectrum measured in this work and its estimated lifetime, a radiative efficiency of 0.306 W m(-2) ppb(-1) (well-mixed gas) was calculated and its 100-year time-horizon global warming potential, GWP100, was estimated to be 8.6. CF3CFO, HC(O)F, and CF2O were identified using infrared spectroscopy as stable end products in the oxidation of HFO-1438ezy(E) in the presence of O2. Two additional fluorinated products were observed and theoretical calculations of the infrared spectra of likely degradation products are presented. The photochemical ozone creation potential of HFO-1438ezy(E) was estimated to be ∼2.15.

Search for compounds contributing to onion-like off-flavor in beer and investigation of the cause of the flavor.

PubMed

Noba, Shigekuni; Yako, Nana; Kobayashi, Minoru; Masuda, Susumu; Watanabe, Tetsuya

2017-10-01

Onion-like off-flavor is a highly undesirable property in beer. Although several compounds that impart onion-like odors have been identified, the individual contribution of these compounds to the onion-like off-flavor in beer is not clear. In the present study, we searched for compounds that impart an onion-like odor by gas chromatography (GC)-olfactometry. The analysis of several types of beer revealed that 2-mercapto-3-methyl-1-butanol (2M3MB) and 3-mercapto-3-methyl-1-butanol (3M3MB) were possible causative compounds. Based on the difference threshold values in beer (0.13 ng/mL for 2M3MB and 17.5 ng/mL for 3M3MB) and the quantification values of these compounds in beer samples, only 2M3MB was considered to contribute to the onion-like off-flavor in beer. A further formation factor analysis of 2M3MB revealed that 2M3MB was formed in hopped wort after fermentation, and that the concentration of 2M3MB increased following the hot aeration treatment of wort. These results suggest that preventing the hot aeration of wort is a key factor for reducing 2M3MB levels in beer. In a previous report, 3-methyl-2-buten-1-ol (3MBol) was speculated to be the precursor of 2M3MB and 3M3MB; however, the results of the present quantification analysis and wort addition tests indicate that 3MBol did not contribute to the formation of 2M3MB in the brewing process and that unknown precursors of 2M3MB originated in wort. Identifying the precursor of 2M3MB may facilitate elucidation of the mechanism of 2M3MB formation. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

The effect of free radical inhibitor on the sensitized radiation crosslinking and thermal processing stabilization of polyurethane shape memory polymers.

PubMed

Hearon, Keith; Smith, Sarah E; Maher, Cameron A; Wilson, Thomas S; Maitland, Duncan J

2013-02-01

The effects of free radical inhibitor on the electron beam crosslinking and thermal processing stabilization of novel radiation crosslinkable polyurethane shape memory polymers (SMPs) blended with acrylic radiation sensitizers have been determined. The SMPs in this study possess novel processing capabilities-that is, the ability to be melt processed into complex geometries as thermoplastics and crosslinked in a secondary step using electron beam irradiation. To increase susceptibility to radiation crosslinking, the radiation sensitizer pentaerythritol triacrylate (PETA) was solution blended with thermoplastic polyurethane SMPs made from 2-butene-1,4-diol and trimethylhexamethylene diisocyanate (TMHDI). Because thermoplastic melt processing methods such as injection molding are often carried out at elevated temperatures, sensitizer thermal instability is a major processing concern. Free radical inhibitor can be added to provide thermal stabilization; however, inhibitor can also undesirably inhibit radiation crosslinking. In this study, we quantified both the thermal stabilization and radiation crosslinking inhibition effects of the inhibitor 1,4-benzoquinone (BQ) on polyurethane SMPs blended with PETA. Sol/gel analysis of irradiated samples showed that the inhibitor had little to no inverse effects on gel fraction at concentrations of 0-10,000 ppm, and dynamic mechanical analysis showed only a slight negative correlation between BQ composition and rubbery modulus. The 1,4-benzoquinone was also highly effective in thermally stabilizing the acrylic sensitizers. The polymer blends could be heated to 150°C for up to five hours or to 125°C for up to 24 hours if stabilized with 10,000 ppm BQ and could also be heated to 125°C for up to 5 hours if stabilized with 1000 ppm BQ without sensitizer reaction occurring. We believe this study provides significant insight into methods for manipulation of the competing mechanisms of radiation crosslinking and thermal stabilization of radiation sensitizers, thereby facilitating further development of radiation crosslinkable thermoplastic SMPs.

The effect of free radical inhibitor on the sensitized radiation crosslinking and thermal processing stabilization of polyurethane shape memory polymers

NASA Astrophysics Data System (ADS)

Hearon, Keith; Smith, Sarah E.; Maher, Cameron A.; Wilson, Thomas S.; Maitland, Duncan J.

2013-02-01

The effects of free radical inhibitor on the electron beam crosslinking and thermal processing stabilization of novel radiation crosslinkable polyurethane shape memory polymers (SMPs) blended with acrylic radiation sensitizers have been determined. The SMPs in this study possess novel processing capabilities—that is, the ability to be melt processed into complex geometries as thermoplastics and crosslinked in a secondary step using electron beam irradiation. To increase susceptibility to radiation crosslinking, the radiation sensitizer pentaerythritol triacrylate (PETA) was solution blended with thermoplastic polyurethane SMPs made from 2-butene-1,4-diol and trimethylhexamethylene diisocyanate (TMHDI). Because the thermoplastic melt processing methods such as injection molding are often carried out at elevated temperatures, sensitizer thermal instability is a major processing concern. Free radical inhibitor can be added to provide thermal stabilization; however, inhibitor can also undesirably inhibit radiation crosslinking. In this study, we quantified both the thermal stabilization and radiation crosslinking inhibition effects of the inhibitor 1,4-benzoquinone (BQ) on polyurethane SMPs blended with PETA. Sol/gel analysis of irradiated samples showed that the inhibitor had little to no inverse effects on gel fraction at concentrations of 0-10,000 ppm, and dynamic mechanical analysis showed only a slight negative correlation between BQ composition and rubbery modulus. The 1,4-benzoquinone was also highly effective in thermally stabilizing the acrylic sensitizers. The polymer blends could be heated to 150 °C for up to 5 h or to 125 °C for up to 24 h if stabilized with 10,000 ppm BQ and could also be heated to 125 °C for up to 5 h if stabilized with 1000 ppm BQ without sensitizer reaction occurring. We believe this study provides significant insight into methods for manipulation of the competing mechanisms of radiation crosslinking and thermal stabilization of radiation sensitizers, thereby facilitating further development of radiation crosslinkable thermoplastic SMPs.

Chemicals from ethanol: the acetone synthesis from ethanol employing Ce0.75Zr0.25O2, ZrO2 and Cu/ZnO/Al2O3.

PubMed

Rodrigues, Clarissa Perdomo; Zonetti, Priscila da Costa; Appel, Lucia Gorenstin

2017-04-04

Acetone is an important solvent and widely used in the synthesis of drugs and polymers. Currently, acetone is mainly generated by the Cumene Process, which employs benzene and propylene as fossil raw materials. Phenol is a co-product of this synthesis. However, this ketone can be generated from ethanol (a renewable feedstock) in one-step. The aim of this work is to describe the influence of physical-chemical properties of three different catalysts on each step of this reaction. Furthermore, contribute to improve the description of the mechanism of this synthesis. The acetone synthesis from ethanol was studied employing Cu/ZnO/Al 2 O 3 , Ce 0.75 Zr 0.25 O 2 and ZrO 2 . It was verified that the acidity of the catalysts needs fine-tuning in order to promote the oxygenate species adsorption and avoid the dehydration of ethanol. The higher the reducibility and the H 2 O dissociation activity of the catalysts are, the higher the selectivity to acetone is. In relation to the oxides, these properties are associated with the presence of O vacancies. The H 2 generation, which occurs during the TPSR, indicates the redox character of this synthesis. The main steps of the acetone synthesis from ethanol are the generation of acetaldehyde, the oxidation of this aldehyde to acetate species (which reduces the catalyst), the H 2 O dissociation, the oxidation of the catalyst producing H 2 , and, finally, the ketonization reaction. These pieces of information will support the development of active catalysts for not only the acetone synthesis from ethanol, but also the isobutene and propylene syntheses in which this ketone is an intermediate. Graphical abstract Acetone from ethanol.