Preparation and characterization of PVDF separators for lithium ion cells using hydroxyl-terminated polybutadiene grafted methoxyl polyethylene glycol (HTPB-g-MPEG) as additive

NASA Astrophysics Data System (ADS)

Li, Hao; Niu, Dong-Hui; Zhou, Hui; Chao, Chun-Ying; Wu, Li-Jun; Han, Pei-Lin

2018-05-01

Hydroxyl-terminated polybutadiene grafted methoxyl polyethylene glycol (HTPB-g-MPEG) with different arm length were synthesized by grafting methoxyl poly(ethylene glycol)s (MPEGs, Mn = 350, 750, 1900 and 5000, respectively) to the hydroxyl-terminated polybutadiene (HTPB) molecule using isophorone diisocyanate (IPDI) as the coupling agent, and blended with PVDF to fabricate porous separators via phase inversion process. By measuring the composition, morphology and ion conductivity etc., the influence of HTPB-g-MPEG on structure and property of blend separators were discussed. Compared with pure PVDF separator with comparable porous structure, the adoption of HTPB-g-MPEG could not only decrease the crystallinity, but also enhance the stability of entrapped liquid electrolyte and corresponding ion conductivity. The cells assembled with such separators showed good initial discharge capacity and cyclic stability.

The effect of polyether functional polydimethylsiloxane on surface and thermal properties of waterborne polyurethane

NASA Astrophysics Data System (ADS)

Zheng, Guikai; Lu, Ming; Rui, Xiaoping

2017-03-01

Waterborne polyurethanes (WPU) modified with polyether functional polydimethylsiloxane (PDMS) were synthesized by pre-polymerization method using isophorone diisocyanate (IPDI) and 1,4-butanediol (BDO) as hard segments and polybutylene adipate glycol (PBA) and polyether functional PDMS as soft segments. The effect of polyether functional PDMS on phase separation, thermal properties, surface properties including surface composition, morphology and wettability were investigated by FTIR, contact angle measurements, ARXPS, SEM-EDS, AFM, TG and DSC. The results showed that the compatibility between urethane hard segment and PDMS modified with polyether was good, and there was no distinct phase separation in both bulk and surface of WPU films. The degradation temperature and low temperature flexibility increased with increasing amounts of polyether functional PDMS. The enrichment of polyether functional PDMS with low surface energy on the surface imparted excellent hydrophobicity to WPU films.

Synthesis and characterization of shape-memory poly carbonate urethane microspheres for future vascular embolization.

PubMed

Liu, Rongrong; Dai, Honglian; Zhou, Qian; Zhang, Qian; Zhang, Ping

2016-08-01

Two types of shape memory poly carbonate urethanes (PCUs) microspheres were synthesized by pre-polymerization and suspension polymerization, based on Polycarbonate diol (PCDL) as the soft segment, Isophorone diisocyanate (IPDI) and 1,6-hexamethylene diisocyanate (HDI) as the hard segments and 1,4-butanediol (BDO) as the chain expanding agent. The structure, crystallinity, and thermal property of the two synthesized PCUs were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Differential scanning calorimetery (DSC), respectively. The results showed that the two types of PCUs exhibited high thermal stability with phase separation and semi-crystallinity. Also, the results of the compression test displayed that the shape fixity and the shape recovery of two PCUs were more than 90% compared to the originals, indicating their similar bio-applicability and shape-memory properties. The tensile strength, elongation at break was enhanced by introducing and increasing content of HDI. The water contact angles of PCUs decreased and their surface tension increased by surface modified with Bovine serum albumin (BSA). Furthermore, the biological study results of two types of PCUs from the platelet adhesion test and the cell proliferation inhibition test indicated they had some biocompatibilites. Hence, the PCU microspheres might represent a smart and shape-memory embolic agent for vascular embolization.

The role of isocyanates in determining the viscoelastic properties of polyurethane

NASA Astrophysics Data System (ADS)

AqilahHamuzan, Hawa; Badri, Khairiah Haji

2016-11-01

Polyurethane (PU) has a unique structure that is dependent on the structure of the starting material used. This research focused on investigating the role of isocyanate groups (NCO) in the determination of the viscoelastic properties of the polymer. Monoester polyol was reacted with three different diisocyanates separately by prepolymerization method. The diisocyanates used were 2,4-diphenyl methane diisocyanate (MDI), toluene 2,4-diisocyanate (TDI) and isophoronediisocyanate (IPDI). Acetone was used as a solvent. IPDI, MDI and TDI were reacted with monoester polyol at ratios of 10:9, 10:10, 10:12 and 10:14 (polyol:diisocyanate). Then, the PU foams produced by the curing process were analyzed by Fourier Transform infrared spectroscopy (FTIR). The FTIR spectra showed the presence of the amide peak (-NH) and the absence of hydroxyl peak (-OH) indicated that the reaction between polyol and diisocyanate has occurred. However, the soxhlet extraction showed that only MDI-based PUs contain crosslinking bond. These cross-linking bond at the ratio of 10:10, 10:12 and 10:14 were 41.3 %,61.1 % and 74.1 % respectively. Thermal properties of the PU foams were determined by differential scanning calorimetry (DSC) and thermogravimetry (TGA) techniques. MDI-based PUs and TDI-based PUs show two values of Tg while IPDI-based PUs only show one Tg value. The tensile strains of PU foams decreased with increasing ratio of isocyanate. Meanwhile, PU foams with ratio of polyol to isocyanate at 10:12 showed the highest tensile stress and modulus compared to at 10:10 and 10:14.

Effect of Propellant Composition to the Temperature Sensitivity of Composite Propellant

NASA Astrophysics Data System (ADS)

Aziz, Amir; Mamat, Rizalman; Amin, Makeen; Ali, Wan Khairuddin Wan

2012-09-01

The propellant composition is one of several parameter that influencing the temperature sensitivity of composite propellant. In this paper, experimental investigation of temperature sensitivity in burning rate of composite propellant was conducted. Four sets of different propellant compositions had been prepared with the combination of ammonium perchlorate (AP) as an oxidizer, aluminum (Al) as fuel and hydroxy-terminated polybutadiene (HTPB) as fuel and binder. For each mixture, HTPB binder was fixed at 15% and cured with isophorone diisocyanate (IPDI). By varying AP and Al, the effect of oxidizer- fuel mixture ratio (O/F) on the whole propellant can be determined. The propellant strands were manufactured using compression molded method and burnt in a strand burner using wire technique over a range of pressure from 1 atm to 31 atm. The results obtained shows that the temperature sensitivity, a, increases with increasing O/F. Propellant p80 which has O/F ratio of 80/20 gives the highest value of temperature sensitivity which is 1.687. The results shows that the propellant composition has significant effect on the temperature sensitivity of composite propellant

A thermosensitive hydrogel based on biodegradable amphiphilic poly(ethylene glycol) polycaprolactone poly(ethylene glycol) block copolymers

NASA Astrophysics Data System (ADS)

Gong, Chang Yang; Qian, Zhi Yong; Liu, Cai Bing; Juan Huang, Mei; Gu, Ying Chun; Wen, Yan Jun; Kan, Bing; Wang, Ke; Dai, Mei; Li, Xing Yi; Gou, Ma Ling; Tu, Ming Jing; Wei, Yu Quan

2007-06-01

A series of low molecular weight poly(ethylene glycol)-polycaprolactone-poly(ethylene glycol) (PEG-PCL-PEG) biodegradable block copolymers were successfully synthesized using isophorone diisocyanate (IPDI) as the coupling agent, and were characterized using 1H NMR and Fourier transform infrared spectroscopy. The aqueous solutions of the PEG-PCL-PEG copolymers displayed a special thermosensitive gel-sol transition when the concentration was above the corresponding critical gel concentration. Gel-sol phase diagrams were recorded using the test-tube-inversion method; they depended on the hydrophilic/hydrophobic balance in the macromolecular structure, as well as some other factors, including the heating history, volume, and the ageing time of the copolymer aqueous solutions and dissolution temperature of the copolymers. As a result, the gel-sol transition temperature range could be altered, which might be very useful for application in injectable drug delivery systems. This work was financially supported by the Chinese Key Basic Research Program (2004CB518800 and 2004CB518807), and the Sichuan Key Project of Science and Technology (06(05SG022-021-02)).

Robust composite-shell microcapsules via pickering emulsification.

PubMed

Patchan, Marcia W; Fuller, Benedict W; Baird, Lance M; Gong, Paul K; Walter, Erich C; Vidmar, Brendan J; Kyei, Ike; Xia, Zhiyong; Benkoski, Jason J

2015-04-08

Microencapsulation technology has been increasingly applied toward the development of self-healing paints. Added to paint as a dry powder prior to spraying, the microcapsules store a liquid that can repair the protective barrier layer if released into a scratch. However, self-healing will not occur unless the microcapsules can withstand spray-painting, aggressive solvents in the paint, and long-term exposure to the elements. We have therefore developed a one-pot synthesis for the production of Pickering microcapsules with outstanding strength, solvent resistance, and barrier properties. Octadecyltrimethoxysilane-filled (OTS) microcapsules form via standard interfacial polycondensation, except that silica nanopowder (10-20 nm diameter) replaces the conventional surfactant or hydrocolloid emulsifier. Isophorone diisocyanate (IPDI) in the OTS core reacts with diethylenetriamine, polyethylenimine, and water to form a hard polymer shell along the interface. Compared to pure polyurea, the silica-polyurea composite improves the shelf life of the OTS by 10 times. The addition of SiO2 prevents leaching of OTS into xylenes and hexanes for up to 80 days, and the resulting microcapsules survive nebulization through a spray gun at 620 kPa in a 500 cSt fluid.

Preparation, thermo-optic property and simulation of optical switch based on azo benzothiazole polymer

NASA Astrophysics Data System (ADS)

Cao, Zhijuan; Qiu, Fengxian; Wang, Qing; Cao, Guorong; Guan, Yijun; Zhuang, Lin; Xu, Xiaolong; Wang, Jie; Chen, Qian; Yang, Dongya

2013-04-01

An azo chromophore molecule 4-[(benzothiazole-2-yl)diazenyl]phenyl-1,3-diamine (BTPD) was prepared with 2-amino benzothiazole and m-phenylenediamine by diazo-coupling reaction. Then, the chromophore molecule BTPD was polymerized with NJ-210 and isophorone diisocyanate (IPDI) to obtain novel azo benzothiazole polymer (BTPU). The structures of BTPD and BTPU were characterized using the Fourier transform infrared, UV-visible spectroscopy, DSC and TGA. The physical properties of the obtained BTPU were investigated. The refractive index ( n) of BTPU was demonstrated at different temperature and wavelength (532, 650 and 850 nm) using attenuated total reflection technique. The transmission loss and dispersion characteristic of BTPU film were investigated using the CCD digital imaging devices and Sellmeyer equation. A Y-branch and 2 × 2 Mach-Zehnder interferometer (MZI) polymeric thermo-optic switches based on the thermo-optic effect of prepared BTPU were proposed and the performance of switches was simulated. The results indicated that the power consumption of the Y-branch thermo-optic switch could be only 0.6 mW. The Y-branch and MZI switching rising and falling times obtained were 8.0 and 1.8 ms.

Investigation on the mechanical properties of polyurea (PU)/melamine formaldehyde (MF) microcapsules prepared with different chain extenders.

PubMed

Hu, Jianfeng; Zhang, Xiaotong; Qu, Jinqing

2018-05-02

There is lack of understanding on controlling of mechanical properties of moisture-curing PU/MF microcapsules which limited its further application. PU/MF microcapsules containing a core of isophorone diisocyanate (IPDI) were prepared with different chain extenders, polyetheramine D400, H 2 O, triethylenetetramine and polyetheramine (PEA) D230 by following a two-step synthesis method in this study. Fourier transform infra-red (FTIR) spectroscopy, Malvern particle sizing, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). And micromanipulation technique was used to identify chemical bonds in the shell, size distributions, structure, thickness, and mechanical properties of microcapsules. The results show that PU/MF microcapsules were successfully prepared. Tr increased from 46.4 ± 13.9 N/m to 75.8 ± 23.3 N/m when extender changed from D400 to D230. And the Tr increased from 51.3 ± 14.1 to 94.8 ± 17.5 N/m when the swelling time increased from 1 to 3h. Morphologies of the shell were utilised to understand the mechanism of reactions in forming the shell materials.

Synthesis, characterization of novel chitosan based water dispersible polyurethanes and their potential deployment as antibacterial textile finish.

PubMed

Arshad, Noureen; Zia, Khalid Mahmood; Jabeen, Farukh; Anjum, Muhammad Naveed; Akram, Nadia; Zuber, Mohammad

2018-05-01

Our current research work comprised of synthesis of a series of novel chitosan based water dispersible polyurethanes. The synthesis was carried out in three steps, in first step, the NCO end capped PU-prepolymer was formed through the reaction between Polyethylene glycol (PEG) (Mn = 600), Dimethylolpropionic acid (DMPA) and Isophorone diisocyanate (IPDI). In second step, the neutralization step was carried out by using Triethylamine (TEA) which resulted the formation of neutralized NCO terminated PU-prepolymer, after that the last step chain extension was performed by the addition of chitosan and followed the formation of dispersion by adding calculated amount of water. The proposed structure of CS-WDPUs was confirmed by using FTIR technique. The antimicrobial activities of the plain weave poly-cotton printed and dyed textile swatches after application of CS-WDPUs were also evaluated. The results showed that the chitosan incorporation in to PU backbone has markedly enhanced the antibacterial activity of WDPUs. These synthesized CS-WDPUs are eco-friendly antimicrobial finishes (using natural bioactive agents such as chitosan) with potential applications on polyester/cotton textiles. Copyright © 2018 Elsevier B.V. All rights reserved.

Understanding Factors that Influence Protective Glove Use among Automotive Spray Painters

PubMed Central

Ceballos, Diana; Reeb-Whitaker, Carolyn; Glazer, Patricia; Murphy-Robinson, Helen; Yost, Michael

2017-01-01

Dermal contact with isocyanate-based coatings may lead to systemic respiratory sensitization. The most common isocyanates found in sprayed automotive coatings are monomeric and oligomeric 1,6-hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI). Most spray painters use thin (4–5 mil) latex gloves that are not effective at preventing dermal exposures when spraying isocyanate paints. Personal interviews with collision repair industry personnel and focus groups with spray painters were held to characterize risk awareness, to examine perceptions and challenges concerning protective glove use and selection, and to generate ideas for protective glove use interventions. The most popular gloves among spray painters were thin (4–5 mil) and thick (14 mil) latex. We found that medium to thick (6–8 mil) nitrile were not always perceived as comfortable and were expected to be more expensive than thin (4–5 mil) latex gloves. Of concern is the users’ difficulty to distinguish between nitrile and latex gloves; latex gloves are now sold in different colors including blue, which has traditionally been associated with nitrile gloves. Even though spray painters were familiar with the health hazards related to working with isocyanate paints; most were not always aware that dermal exposure to isocyanates could contribute to the development of occupational asthma. There is a need for more research to identify dermal materials that are protective against sprayed automotive coatings. Automotive spray painters and their employers need to be educated in the selection and use of protective gloves, specifically on attributes such as glove material, color, and thickness. PMID:24215135

Fully glutathione degradable waterborne polyurethane nanocarriers: Preparation, redox-sensitivity, and triggered intracellular drug release.

PubMed

Omrani, Ismail; Babanejad, Niloofar; Shendi, Hasan Kashef; Nabid, Mohammad Reza

2017-01-01

Polyurethanes are important class of biomaterials that are extensively used in medical devices. In spite of their easy synthesis, polyurethanes that are fully degradable in response to the intracellular reducing environment are less explored for controlled drug delivery. Herein, a novel glutathione degradable waterborne polyurethane (WPU) nanocarrier for redox triggered intracellular delivery of a model lipophilic anticancer drug, doxorubicin (DOX) is reported. The WPU was prepared from polyaddition reaction of isophorone diisocyanate (IPDI) and a novel linear polyester polyol involving disulfide linkage, disulfide labeled chain extender, dimethylolpropionic acid (DMPA) using dibutyltin dilaurate (DBTDL) as a catalyst. The resulting polyurethane self-assembles into nanocarrier in water. The dynamic light scattering (DLS) measurements and scanning electron microscope (SEM) revealed fast swelling and disruption of nanocarriers under an intracellular reduction-mimicking environment. The in vitro release studies showed that DOX was released in a controlled and redox-dependent manner. MTT assays showed that DOX-loaded WPU had a high in vitro antitumor activity in both HDF noncancer cells and MCF- 7 cancer cells. In addition, it is found that the blank WPU nanocarriers are nontoxic to HDF and MCF-7 cells even at a high concentration of 2mg/mL. Hence, nanocarriers based on disulfide labeled WPU have appeared as a new class of biocompatible and redox-degradable nanovehicle for efficient intracellular drug delivery. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of Branched Gap Synthesis Parameters on Mechanical Properties of Rocket Propellants

DTIC Science & Technology

1995-12-01

modulus hydroxyl functionality glycidyl azide polymer hexanetriol hydroxy-terminated polybutadiene isophorone diisocyanate hydroxyl equivalent... hexanetriol (HT), glycerol and polyethylene glycol (PEG) with MW 600. The reaction was carried out with one polyol or a blend of two polyols and

Synthesis of water-based cationic polyurethane for antibacterial and gene delivery applications.

PubMed

Wu, Geng-Hsi; Hsu, Shan-Hui

2016-10-01

Cationic polymers are often used as antimicrobial materials and transfection reagents. Water-based process could reduce environmental pollution and prevent the risk of solvent residue in the final product. In this study, waterborne biodegradable cationic polyurethane (WCPU) was synthesized by reacting polycaprolactone (PCL diol), isophorone diisocyanate (IPDI), and N-methyldiethanolamine (N-MDEA) under 75°C. An aqueous dispersion of WCPU nanoparticles (NPs) could be acquired by vigorous stirring under acidic condition. The particles in the dispersion had an average size of ∼80nm and a zeta potential of ∼60mV. When cast into films, the contact angle of the film was ∼67° and the zeta potential was ∼16mV. WCPU NPs demonstrated excellent antibacterial activity against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) (100% inhibition with a contact time of 3h). Meanwhile, the antibacterial ratio of WCPU films to E. coli and S. aureus reached 100% after 24h of contact. Moreover, WCPU NPs could be used as a transfection reagent without significant toxicity for concentrations less than 1000μg/mL and showed the ability to condensate plasmid DNA. The transfection efficiency for HEK293T cells and hBMSCs was ∼60% and ∼30% at 48h, respectively, after the transfection. Therefore, the WCPU synthesized in this study has potential antibacterial and gene delivery applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Preparation and thermo-optic switch properties based on chiral azobenzene-containing polyurethane

NASA Astrophysics Data System (ADS)

Ye, Feiyan; Qiu, Fengxian; Yang, Dongya; Cao, Guorong; Guan, Yijun; Zhuang, Lin

2013-07-01

A chiral azo chromophore compound 4-(4'-nitro-phenyl-diazenyl)-phenyl-1,2-propanediol ether (NPDPPE) was prepared with p-nitroaniline, phenol and R(-)-3-chloro-1,2-propanediol by the diazo-coupling reaction. Then, the chromophore molecule NPDPPE was polymerized with isophorone diisocyanate (IPDI) to obtain novel chiral azobenzene-containing polyurethane (CACPU). The chemical structures of chromophore molecule and CACPU were characterized by the FT-IR and UV-visible spectroscopy. The physical properties (thermal conductivity, thermal diffusion coefficient, and specific heat capacity) and mechanical properties (tensile strength, elongation at break and hardness) of CACPU thin films were measured. The refractive index and thermo-optic (TO) coefficient (dn/dT) of CACPU thin film was investigated for TE (transversal electric) polarizations by using an attenuated total reflection (ATR) configuration at the wavelengths of 532, 650 and 850 nm. The transmission loss of film was measured using the charge coupled device (CCD) digital imaging devices. A Y-branch switch and Mach-Zehnder interferometer (MZI) thermo-optic switches based on thermo-optic effect were proposed and the performances of switches were simulated. The results showed that the power consumption of the Y-branch thermo-optic switch was only 3.28 mW. The rising and falling times of Y-branch and MZI switches were 12.0 ms and 2.0 ms, respectively. The conclusion has potential significance to improve and develop new Y-branch digital optical switch (DOS), MZI thermo-optic switch, directional coupler (DC) switch and optical modulators.

Synthesis, physical properties and simulation of thermo-optic switch based on azo benzothiazole heterocyclic polymer

NASA Astrophysics Data System (ADS)

Qiu, Fengxian; Chen, Caihong; Zhou, Qiaolan; Cao, Zhijuan; Cao, Guorong; Guan, Yijun; Yang, Dongya

2014-05-01

A chromophore molecule 4-[(benzothiazole-2-yl)diazenyl]phenyl-1,3-diamine (BTPD) was prepared with 2-amino benzothiazole and m-phenylenediamine by diazo-coupling reaction. Then, the BTPD was polymerized with polyether polyol (NJ-220) and isophorone diisocyanate (IPDI) to obtain novel azo benzothiazole polyurethane-urea (BTPUU). The chemical structures of BTPD and BTPUU were characterized by FT-IR and UV-visible spectroscopy. The thermal and mechanical properties of BTPUU film were investigated. The refractive index and transmission loss of BTPUU film were measured at different temperatures and different laser wavelengths (532 nm, 650 nm and 850 nm) by an attenuated total reflection (ATR) technique and CCD digital imaging devices. The thermo-optic coefficients of BTPUU are -4.7086 × 10-4 °C-1 (532 nm), -6.5257 × 10-4 °C-1 (650 nm) and -5.1029 × 10-4 °C-1 (850 nm), respectively. A Y-branch switch and Mach-Zehnder interferometer (MZI) thermo-optic switches based on thermo-optic effect were proposed and the performances of the switches were simulated, respectively. The results show that the power consumption of the Y-branch thermo-optic switch is only 3.28 mW. The response times of Y-branch and MZI switches are 8.0 ms and 2.0 ms, respectively. The results indicate that the prepared BTPUU has high potential for the applications of the Y-branch digital optical switch (DOS), MZI thermo-optic switch, directional coupler (DC) switch and optical modulators.

Design and synthesis of bio-based UV curable PU acrylate resin from itaconic acid for coating applications

PubMed Central

Patil, Deepak M.; Phalak, Ganesh A.; Mhaske, S. T.

2017-01-01

Abstract UV curable PUA resin was successfully synthesized from polyol based on sustainable resource originated from itaconic acid (IA), isophorone diisocyanate (IPDI) and 2-hydroxyethyl methacrylate (HEMA). A polyol was synthesized by condensation reaction of IA with 16-hexanediol in the presence of p-Toluenesulfonic acid (pTSA). The synthesized PUA resin was characterized for its structural elucidation by using Fourier Transform Infrared Spectrophotometer (FTIR), 1H and 13C NMR spectroscopy. The synthesized UV curable PUA resin was incorporated in varying concentrations in conventional PUA coating system. The effects of varying concentration of synthesized UV curable PUA resin on rheology, crystallinity, thermal and coating properties were evaluated. The rheological behavior of the resins were evaluated at variable stress and result showed decrease in viscosity of resin as concentration of synthesized UV curable PUA resin increases in conventional PUA resin. The cured coatings have been evaluated for glass transition temperature (T g) and thermal behavior by differential scanning calorimeter and thermogravimetric analysis respectively. The degree of crystallinity of the coatings was determined from X-ray diffraction patterns using the PFM program. It was found that increase in the mass proportion of IA based PUA in coatings, the coating becomes more rigid and crystalline. The synthesized UV curable PUA coatings showed interesting mechanical, chemical, solvent and thermal properties as compared to the conventional PUA. Further, cured coatings were also evaluated for gel content and water absorption. PMID:29491798

40 CFR 721.8079 - Isophorone diisocyanate neopentyl glycol adipate polyurethane prepolymer.

Code of Federal Regulations, 2010 CFR

2010-07-01

... glycol adipate polyurethane prepolymer. 721.8079 Section 721.8079 Protection of Environment ENVIRONMENTAL... adipate polyurethane prepolymer. (a) Chemical substance and significant new uses subject to reporting. (1... polyurethane prepolymer (PMN P-94-1743) is subject to reporting under this section for the significant new uses...

Development of low viscosity alkane-based urethane for connector potting applications

NASA Technical Reports Server (NTRS)

Morris, D. E.

1983-01-01

Two series of saturated hydrocarbon-based urethanes were prepared with isophorone diisocyanate and one series with methyl bis (4-cyclohexyl isocyanate). The urethanes with molecular weights as great as 2500 had viscosities low enough and a working life long enough to be used in potting, molding, and coating applications. Specimens were prepared and mechanical properties such as hardness, tensile strength elongation, and tear strength were determined. Thermomechanical properties (glass transition and expansion coefficient) and thermogravimetric properties were determined.

Emulsification Of Eutectic Salt Mixtures In Fluid Vehicles

NASA Astrophysics Data System (ADS)

Vanderhoff, J. W.; El-Aasser, M. S.; Hawkins, T. W.

1988-05-01

High-internal-phase-volume emulsions of 75 volt 3/18/79 potassium iodide/sodium iodide/ urea model eutectic salt mixture in 83.5/16.5 Sartomer R-45HT hydroxy-terminated polybutadi-ene/Nujol mineral oil binder mixture were prepared at 60°C using water-in-oil emulsifiers and cured with isophorone diisocyanate or Desmodur N-100. The Nujol mineral oil enhanced the emulsification with a negligible reduction in the tensile properties of the cured elastomer. The average emulsion droplet sizes were ca. 200 nm initially, but increased slowly during curing to 500-1000 nm. The coalescence of the emulsion droplets followed the second-order dependence predicted by the von Smoluchowski diffusion-controlled flocculation; the rate constants were 1.05x10-18 and 9.58x10-18 cc/droplet-sec for dirnethyldioctadecylammonium bromide and Span 85 sorbitan trioleate, respectively. The isophorone diisocyanate reacted with emulsifiers containing primary hydroxyl or amine groups, to give unstable emulsions or no emulsions at all. Dimethyldioctadecylammonium bromide with no primary hydroxyl or amine groups, however, did not react with isocyanates and gave stable emulsions. The reaction of the R-45HT hydroxy-terminated polybutadiene with isophorone diisocyanate followed the expec-ted second-order kinetics with a rate constant of 3.42x10-4 liters/mole-sec at 60°C. The tensile properties of the cured elastomers and emulsions generally increased with increasing NCO/OH ratio up to 1.6/1.0. With increasing volume fraction of dispersed phase, the maximum stress (tensile strength) decreased, the maximum strain (percent elongation) increased, and the initial modulus (tensile modulus) decreased, in contrast to the behavior of conventional filled polymer systems; however, the maximum stresses were in accord with theoretical values for a filled polymer in which the filler particles bear no load, the initial moduli were in accord with the predictions of an isostrain model, and the maximum strain increased with in-creasing volume fraction of dispersed phase; these unusual variations, which were attributed to the liquid nature of the emulsion droplets, were used to estimate the elastomer proper-ties required to give the desired properties: 60-100 psi maximum stress, 80-150% maximum strain, and 500-2000 psi initial modulus for an 88/12 eutectic salt/crosslinked polybutadi-ene composite containing 20% aluminum particles. The addition of 20% aluminum particles gave a modest improvement in tensile properties, and the addition of 2.5% or 3.5% submicroscopic carbon black particles gave a greater improvement; however, the tensile properties were still slightly short of the desired properties.

New biobased high functionality polyols and their use in polyurethane coatings.

PubMed

Pan, Xiao; Webster, Dean C

2012-02-13

High-functionality polyols for application in polyurethanes (PUs) were prepared by epoxide ring-opening reactions from epoxidized sucrose esters of soybean oil-epoxidized sucrose soyates-in which secondary hydroxyl groups were generated from epoxides on fatty acid chains. Ester polyols were prepared by using a base-catalyzed acid-epoxy reaction with carboxylic acids (e.g., acetic acid); ether polyols were prepared by using an acid-catalyzed alcohol-epoxy reaction with monoalcohols (e.g., methanol). The polyols were characterized by using gel permeation chromatography, FTIR spectroscopy, (1)H NMR spectroscopy, differential scanning calorimetry (DSC), and viscosity measurements. PU thermosets were prepared by using aliphatic polyisocyanates based on isophorone diisocyanate and hexamethylene diisocyanate. The properties of the PUs were studied by performing tensile testing, dynamic mechanical analysis, DSC, and thermogravimetric analysis. The properties of PU coatings on steel substrates were evaluated by using ASTM methods to determine coating hardness, adhesion, solvent resistance, and ductility. Compared to a soy triglyceride polyol, sucrose soyate polyols provide greater hardness and range of cross-link density to PU thermosets because of the unique structure of these macromolecules: well-defined compact structures with a rigid sucrose core coupled with high hydroxyl group functionality. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis, characterization, shrinkage and curing kinetics of a new low-shrinkage urethane dimethacrylate monomer for dental applications.

PubMed

Atai, Mohammad; Ahmadi, Mehdi; Babanzadeh, Samal; Watts, David C

2007-08-01

The aim of the study was to synthesize and characterize an isophorone-based urethane dimethacrylate (IP-UDMA) resin-monomer and to investigate its shrinkage and curing kinetics. The IP-UDMA monomer was synthesized through the reaction of polyethylene glycol 400 and isophorone diisocyanate followed by reacting with HEMA to terminate it with methacrylate end groups. The reaction was followed using a standard back titration method and FTIR spectroscopy. The final product was purified and characterized using FTIR, (1)H NMR, elemental analysis and refractive index measurement. The shrinkage-strain of the specimens photopolymerized at circa 700mW/cm(2) was measured using the bonded-disk technique at 23, 35, and 45 degrees C. Initial shrinkage-strain-rates were obtained by numerical differentiation of shrinkage-strain data with respect to time. Degree-of-conversion of the specimens was measured using FTIR spectroscopy. The thermal curing kinetics of the monomer were also studied by differential scanning calorimetry (DSC). The characterization methods confirmed the suggested reaction route and the synthesized monomer. A low shrinkage-strain of about 4% was obtained for the new monomer. The results showed that the shrinkage-strain-rate of the monomer followed the autocatalytic model of Kamal and Sourour [Kamal MR, Sourour S. Kinetic and thermal characterization of thermoset cure. Polym Eng Sci 1973;13(1):59-64], which is used to describe the reaction kinetics of thermoset resins. The model parameters were calculated by linearization of the equation. The model prediction was in a good agreement with the experimental data. The properties of the new monomer compare favorably with properties of the commercially available resins.

Diisocyanate mediated polyether modified gelatin drug carrier for controlled release

PubMed Central

Vijayakumar, Vediappan; Subramanian, Kaliappagounder

2013-01-01

Gelatin is an extensively studied biopolymer hydrogel drug carrier due to its biocompatibility, biodegradability and non-toxicity of its biodegraded products formed in vivo. But with the pristine gelatin it is difficult to achieve a controlled and desirable drug release characteristics due to its structural and thermal lability and high solubility in aqueous biofluids. Hence it is necessary to modify its solubility and structural stability in biofluids to achieve controlled release features with improved drug efficacy and broader carrier applications. In the present explorations an effort is made in this direction by cross linking gelatin to different extents using hitherto not studied isocyanate terminated poly(ether) as a macrocrosslinker prepared from poly(ethylene glycol) and isophorone diisocyanate in dimethyl sulfoxide. The crosslinked samples were analyzed for structure by Fourier transform-infrared spectroscopy, thermal behavior through thermogravimetric analysis and differential scanning calorimetry. The cross linked gelatins were biodegradable, insoluble and swellable in biofluids. They were evaluated as a carrier for in vitro drug delivery taking theophylline as a model drug used in asthma therapy. The crosslinking of gelatin decreased the drug release rate by 10–20% depending upon the extent of crosslinking. The modeled drug release characteristics revealed an anomalous transport mechanism. The release rates for ampicillin sodium, 5-fluorouracil and theophylline drugs in a typical crosslinked gelatin carrier were found to depend on the solubility and hydrophobicity of the drugs, and the pH of the fluid. The observed results indicated that this material can prove its mettle as a viable carrier matrix in drug delivery applications. PMID:24493973

Polyfibroblast: A Self-Healing and Galvanic Protection Additive

DTIC Science & Technology

2013-09-25

Specifically we looked at emulsifier (Gum Arabic vs. SiC^), polymer-forming monomer (IPDI vs. BCI ), silane molecular weight (C12 vs. C18 vs. C8-C18...le+6J tu ie+4- le+2 U le+0 ■ Coating ■ Scratch BCI IPDI Isocyanate Type ICoating |Scratch Figure 3: A) Corrosion resistance of the...surprising. The type of monomer also did not appear to matter in these measurements. Whether polymerized from IPDI or BCI , the extent of self-healing

Morphology of Thermally Degraded PU and Irradiated PE

NASA Astrophysics Data System (ADS)

Harris, Douglas; Gillen, Kenneth; Celina, Mathias; Assink, Roger

2001-03-01

Several 1H and 13C NMR techniques have been applied to study the morphology and chemical structure of thermally degraded polyurethane rubber and irradiated polyethylene cable insulation. The combination of heat and presence of air results in oxidation of the hydroxyl-terminated polybutadiene/isophorone diisocyanate polyurethane and the gel content increases. The oxidation is inhomogeneous: pristine regions remain with a length scale of approximately 20 nm. The morphology and oxidation products were characterized by 1H spin diffusion with 13C detection. In addition, dynamics were probed with 1H and 2D WISE experiments. Radiation of cross-linked polyethylene cable insulation obeys anomalous aging behavior where lower temperature can result in a greater loss in ultimate tensile elongation. Annealing of the irradiated polyethylene allows significant recovery of mechanical properties. Analysis of 13C NMR data was used to study this "Lazarus effect" and the inverse temperature relationship. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy under Contract DE-AC04-94AL8500.

Determinants of isocyanate exposures in auto body repair and refinishing shops.

PubMed

Woskie, S R; Sparer, J; Gore, R J; Stowe, M; Bello, D; Liu, Y; Youngs, F; Redlich, C; Eisen, E; Cullen, M

2004-07-01

As part of the Survey of Painters and Repairers of Auto bodies by Yale (SPRAY), the determinants of isocyanate exposure in auto body repair shops were evaluated. Measurements (n = 380) of hexamethylene diisocyanate-based monomer and polyisocyanate and isophorone diisocyanate-based polyisocyanate were collected from 33 auto body shops. The median total reactive isocyanate concentrations expressed as mass concentration of the NCO functional group were: 206 microg NCO/m3 for spray operations; 0.93 microg NCO/m3 for samples collected in the vicinity of spray operations done on the shop floor (near spray); 0.05 microg NCO/m3 for office or other shop areas adjacent to spray areas (workplace background); 0.17 microg NCO/m3 for paint mixing and gun cleaning operations (mixing); 0.27 microg NCO/m3 for sanding operations. Exposure determinants for the sample NCO mass load were identified using linear regression, tobit regression and logistic regression models. For spray samples in a spray booth the significant determinants were the number of milliliters of NCO applied, the gallons of clear coat used by the shop each month and the type of spray booth used (custom built crossdraft, prefabricated crossdraft or downdraft/semi-downdraft). For near spray (bystander) samples, outdoor temperature >65 degrees F (18 degrees C) and shop size >5000 feet2 (465 m2) were significant determinants of exposure levels. For workplace background samples the shop annual income was the most important determinant. For sanding samples, the shop annual income and outdoor temperature >65 degrees F (18 degrees C) were the most significant determinants. Identification of these key exposure determinants will be useful in targeting exposure evaluation and control efforts to reduce isocyanate exposures.

Synthesis of waterborne polyurethane containing alkoxysilane side groups and the properties of the hybrid coating films

NASA Astrophysics Data System (ADS)

Li, Qi; Guo, Longhai; Qiu, Teng; Xiao, Weidong; Du, Dianxing; Li, Xiaoyu

2016-07-01

A series of waterborne polyurethane (WPU) containing alkoxysilane side groups were synthesized by using the dihydroxy functionalized alkoxysilane. The diol with trimethoxysilane groups at the side chains was synthesized via Michael addition between 3-(methacryloxypropyl)trimethoxysilane (MAPTS) and diethanolamine (DEA). The silane diol was applied as the chain extender for the NCO-endcapped prepolymer of isophorone diisocyanate, polycarbonate diol, 2,2-bis(hydroxymethyl) butyric acid and 1,4-butanediol. The products with the silane content varied from 1.2 to 16.5 wt% were dispersed in water after neutralization. The effect of the silane diol on the particle size and morphology of the WPU dispersion was studied by dynamic light scattering (DLS) and transmission electron microscopy (TEM), respectively. X-ray photoelectron spectroscopy (XPS) characterization was carried out on the coating film of the WPU, revealing that the long flexible side chain is favorable for the silane components to emigrate toward the film surface and crosslink during the film formation process. As a result, both the surface contact angle to water and water adsorption of the WPU coating films increased with the silane content. Furthermore, the mechanical properties including the modulus and tensile strength of the films were also improved by the incorporation of silane diol.

Isophorone

Integrated Risk Information System (IRIS)

Isophorone ; CASRN 78 - 59 - 1 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Effects

Effect of the incorporation of chitosan on the physico-chemical, mechanical properties and biological activity on a mixture of polycaprolactone and polyurethanes obtained from castor oil.

PubMed

Arévalo, Fabian; Uscategui, Yomaira L; Diaz, Luis; Cobo, Martha; Valero, Manuel F

2016-11-01

In the present study, polyurethane materials were obtained from castor oil, polycaprolactone and isophorone diisocyanate by incorporating different concentrations of chitosan (0.5, 1.0 and 2.0% w/w) as an additive to improve the mechanical properties and the biological activity of polyurethanes. The polyurethanes were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, stress/strain fracture tests and swelling analysis, and the hydrophilic character of the surface was determined by contact angle trials. The objectives of the study were to evaluate the effect of the incorporation of chitosan on the changes of the physico-chemical and mechanical properties and the in vitro biological activity of the polyurethanes. It was found that the incorporation of chitosan enhances the ultimate tensile strength of the polyurethanes and does not affect the strain at fracture in polyurethanes with 5% w/w of polycaprolactone and concentrations of chitosan ranging from 0 to 2% w/w. In addition, PCL5-Q-PU formulations and their degradation products did not affect cell viability of L929 mouse fibroblast and 3T3, respectively. Polyurethane formulations showed antibacterial activities against Staphylococcus aureus and Escherichia coli bacteria. The results of this study have highlighted the potential biomedical application of this polyurethanes related to soft and cardiovascular tissues. © The Author(s) 2016.

40 CFR 721.10610 - Toluene diisocyanate, polymers with polyalkylene glycol (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Toluene diisocyanate, polymers with... New Uses for Specific Chemical Substances § 721.10610 Toluene diisocyanate, polymers with polyalkylene... substances identified generically as toluene diisocyanate, polymers with polyalkylene glycol (PMNs P-11-635...

40 CFR 721.10608 - Aliphatic diisocyanate polymer with alkanediol and alkylglycol (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Aliphatic diisocyanate polymer with... Significant New Uses for Specific Chemical Substances § 721.10608 Aliphatic diisocyanate polymer with.... (1) The chemical substance identified generically as aliphatic diisocyanate polymer with alkanediol...

40 CFR 721.10610 - Toluene diisocyanate, polymers with polyalkylene glycol (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Toluene diisocyanate, polymers with... New Uses for Specific Chemical Substances § 721.10610 Toluene diisocyanate, polymers with polyalkylene... substances identified generically as toluene diisocyanate, polymers with polyalkylene glycol (PMNs P-11-635...

40 CFR 721.10608 - Aliphatic diisocyanate polymer with alkanediol and alkylglycol (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Aliphatic diisocyanate polymer with... Significant New Uses for Specific Chemical Substances § 721.10608 Aliphatic diisocyanate polymer with.... (1) The chemical substance identified generically as aliphatic diisocyanate polymer with alkanediol...

Catalytic conversion of isophorone to jet-fuel range aromatic hydrocarbons over a MoO(x)/SiO2 catalyst.

PubMed

Chen, Fang; Li, Ning; Wang, Wentao; Wang, Aiqin; Cong, Yu; Wang, Xiaodong; Zhang, Tao

2015-07-28

For the first time, jet fuel range C8-C9 aromatic hydrocarbons were synthesized in high carbon yield (∼80%) by the catalytic conversion of isophorone over MoO(x)/SiO2 at atmospheric pressure. A possible reaction pathway was proposed according to the control experiments and the intermediates generated during the reaction.

Comparative Study of Structure-Property Relationships in Polymer Networks Based on Bis-GMA, TEGDMA and Various Urethane-Dimethacrylates

PubMed Central

Barszczewska-Rybarek, Izabela; Jurczyk, Sebastian

2015-01-01

The effect of various dimethacrylates on the structure and properties of homo- and copolymer networks was studied. The 2,2-bis-[4-(2-hydroxy-3-methacryloyloxypropoxy)phenyl]-propane) (Bis-GMA), triethylene glycol dimethacrylate (TEGDMA) and 1,6-bis-(methacryloyloxy-2-ethoxycarbonylamino)-2,4,4-trimethylhexane (HEMA/TMDI), all popular in dentistry, as well as five urethane-dimethacrylate (UDMA) alternatives of HEMA/TMDI were used as monomers. UDMAs were obtained from mono-, di- and tri(ethylene glycol) monomethacrylates and various commercial diisocyanates. The chemical structure, degree of conversion (DC) and scanning electron microscopy (SEM) fracture morphology were related to the mechanical properties of the polymers: flexural strength and modulus, hardness, as well as impact strength. Impact resistance was widely discussed, being lower than expected in the case of poly(UDMA)s. It was caused by the heterogeneous morphology of these polymers and only moderate strength of hydrogen bonds between urethane groups, which was not high enough to withstand high impact energy. Bis-GMA, despite having the highest polymer morphological heterogeneity, ensured fair impact resistance, due to having the strongest hydrogen bonds between hydroxyl groups. The TEGDMA homopolymer, despite being heterogeneous, produced the smoothest morphology, which resulted in the lowest brittleness. The UDMA monomer, having diethylene glycol monomethacrylate wings and the isophorone core, could be the most suitable HEMA/TMDI alternative. Its copolymer with Bis-GMA and TEGDMA had improved DC as well as all the mechanical properties. PMID:28787999

Conjugation of diisocyanate side chains to dimethacrylate reduces polymerization shrinkage and increases the hardness of composite resins.

PubMed

Jan, Yih-Dean; Lee, Bor-Shiunn; Lin, Chun-Pin; Tseng, Wan-Yu

2014-04-01

Polymerization shrinkage is one of the main causes of dental restoration failure. This study tried to conjugate two diisocyanate side chains to dimethacrylate resins in order to reduce polymerization shrinkage and increase the hardness of composite resins. Diisocyanate, 2-hydroxyethyl methacrylate, and bisphenol A dimethacrylate were reacted in different ratios to form urethane-modified new resin matrices, and then mixed with 50 wt.% silica fillers. The viscosities of matrices, polymerization shrinkage, surface hardness, and degrees of conversion of experimental composite resins were then evaluated and compared with a non-modified control group. The viscosities of resin matrices increased with increasing diisocyanate side chain density. Polymerization shrinkage and degree of conversion, however, decreased with increasing diisocyanate side chain density. The surface hardness of all diisocyanate-modified groups was equal to or significantly higher than that of the control group. Conjugation of diisocyanate side chains to dimethacrylate represents an effective means of reducing polymerization shrinkage and increasing the surface hardness of dental composite resins. Copyright © 2012. Published by Elsevier B.V.

Quantification of organic solvents in aquatic toys and swimming learning devices and evaluation of their influence on the smell properties of the corresponding products.

PubMed

Wiedmer, Christoph; Buettner, Andrea

2018-04-01

Based on the observation that the characteristic odour of inflatable aquatic toys for children is predominantly caused by residues of hazardous organic solvents, the concentrations of cyclohexanone, isophorone and phenol were determined in a selection of 20 products obtained from online suppliers located in Germany. Analytes were extracted with dichloromethane after the addition of non-labelled internal standards, and the volatile fraction was isolated using solvent-assisted flavour evaporation (SAFE). Extracts were then concentrated by Vigreux distillation and analysed by means of gas chromatography with mass spectrometric detection (GC-MS). Furthermore, each sample was evaluated regarding its specific olfactory properties by an expert sensory panel. While some samples did not contain significant amounts of solvents, cyclohexanone concentrations above the lower limit of quantification (LLOQ) were determined in nine samples with six samples containing high concentrations ranging from about 1 to 7 g/kg cyclohexanone. Isophorone concentrations above the LLOQ were observed in eight samples. Thereby, six products contained between 0.3 and 1.6 g/kg isophorone and the remaining two samples contained even about 5 g/kg isophorone, each. Likewise, phenol concentrations exceeded the LLOQ in 14 cases, with four samples containing elevated amounts ranging from about 140 to 280 mg/kg phenol.

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Pollutants for Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam production—diisocyanate emissions. Each new and existing slabstock affected source shall comply...

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Pollutants for Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam production—diisocyanate emissions. Each new and existing slabstock affected source shall comply...

40 CFR 721.10624 - Dicyclohexylmethane-4,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

..., polymer with ethoxylated, propoxylated polyethers (generic). 721.10624 Section 721.10624 Protection of...,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (generic). (a) Chemical substance... dicyclohexylmethane-4,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (PMN P-12-326) is subject to...

40 CFR 721.10624 - Dicyclohexylmethane-4,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

..., polymer with ethoxylated, propoxylated polyethers (generic). 721.10624 Section 721.10624 Protection of...,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (generic). (a) Chemical substance... dicyclohexylmethane-4,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (PMN P-12-326) is subject to...

40 CFR 721.10606 - Alkyl substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkyl substituted alkanediol polymer... alkanediol polymer with aliphatic and alicyclic diisocyanates (generic). (a) Chemical substance and... substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (PMN P-11-486) is subject to...

40 CFR 721.10606 - Alkyl substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkyl substituted alkanediol polymer... alkanediol polymer with aliphatic and alicyclic diisocyanates (generic). (a) Chemical substance and... substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (PMN P-11-486) is subject to...

40 CFR 721.10605 - Polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Polyoxyalkylene ether, polymer with..., polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic). (a) Chemical substance and... polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (PMN P-11-485) is subject...

40 CFR 721.10605 - Polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Polyoxyalkylene ether, polymer with..., polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic). (a) Chemical substance and... polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (PMN P-11-485) is subject...

Mass spectrometry-based analysis of murine bronchoalveolar lavage fluid following respiratory exposure to 4,4'-methylene diphenyl diisocyanate aerosol.

PubMed

Hettick, Justin M; Law, Brandon F; Lin, Chen-Chung; Wisnewski, Adam V; Siegel, Paul D

2018-06-01

1. Diisocyanates are highly reactive electrophiles utilized in the manufacture of a wide range of polyurethane products and have been identified as causative agents of occupational allergic respiratory disease. However, in spite of the significant occupational health burden associated with diisocyanate-induced asthma, the mechanism of disease pathogenesis remains largely unknown. 2. To better understand the fate of inhaled diisocyanates, a nose-only aerosol exposure system was constructed and utilized to expose a BALB/c mouse model to an aerosol generated from 4,4'-methylene diphenyl diisocyanate (MDI). Tissue and bronchoalveolar lavage samples were evaluated 4 and 24 h post-exposure for evidence of diisocyanate-protein haptenation, and a label-free quantitative proteomics strategy was employed to evaluate relative changes to the protein content of the cellular fraction of the lavage fluid. 3. Following MDI aerosol exposure, expression of the number of proteins with immunological or xenobiotic metabolism relevance is increased, including endoplasmin, cytochrome P450 and argininosuccinate synthase. Western blot analysis indicated MDI-conjugated protein in the lavage fluid, which was identified as serum albumin. 4. Tandem mass spectrometry analysis of MDI-albumin revealed MDI conjugation occurs at a dilysine motif at Lys525, as well as at a glutamine-lysine motif at Lys414, in good agreement with previously published in vitro data on diisocyanate-conjugated serum albumin.

Effect of diisocyanate linkers on the degradation characteristics of copolyester urethanes as potential drug carrier matrices.

PubMed

Mathew, Simi; Baudis, Stefan; Neffe, Axel T; Behl, Marc; Wischke, Christian; Lendlein, Andreas

2015-09-01

In this study, the effect of three aliphatic diisocyanate linkers, L-lysine diisocyanate ethyl ester (LDI), hexamethylene diisocyanate (HDI), and racemic 2,2,4-/2,4,4-trimethyl hexamethylene diisocyanate (TMDI), on the degradation of oligo[(rac-lactide)-co-glycolide] (64:36 mol%) based polyester urethanes (PEU) was examined. Samples were characterized for their molecular weight, mass loss, water uptake, sequence structure, and thermal and mechanical properties. Compared to non-segmented PLGA, the PEU showed higher water uptake and generally degraded faster. Interestingly, the rate of degradation was not directly correlating with the hydrophilicity of the diisocyanate moieties; instead, competing intra-/intermolecular hydrogen bonds in between urethane moieties appear to substantially decrease the rate of degradation for LDI-derived PEU. By comparing microparticles (μm) and films (mm) as matrices of different dimensions, it was shown that autocatalysis remains a contributor to degradation of the larger-sized PEU matrices as it is typical for non-segmented lactide/glycolide copolymers. The shown capacity of lactide/glycolide-based multiblock copolymers to degrade faster than PLGA and exhibit improved elastic properties could be of interest for medical implants and drug release systems. Copyright © 2015 Elsevier B.V. All rights reserved.

Introduction to Rocket Propulsion

DTIC Science & Technology

1991-12-01

such as epoxies, MAPO (a trifunctional aziridinyl phosphine oxide), MT-4, various isocyanates, such a TDI, HDI, IPDI, and polyols such as trimethylol...propane (2) Burning rate catalysts, such as copper chromite (or chromate), ferrocene , and several less migratory derivatives of this organic iron

Detection of diisocyanates in nesting material associated with mortality in pigeon chicks.

PubMed

Mukai, Motoko; Woods, Leslie W; Stump, Samuel; Ebel, Joseph G; Levitt, Ariana S; Frey, Margaret W; Smith, Jeanne; Uzal, Francisco A; Poppenga, Robert H; Puschner, Birgit

2014-03-01

Diisocyanates, commonly used in the production of polyurethane foams, paints, elastomers, varnishes, and coatings, are considered among the most hazardous inhalation toxicants. The present report describes 2 unusual cases of mortality in pigeon chicks associated with nesting material contaminated by diisocyanates. Case 1 was submitted by a racing pigeon breeder who had lost all the hatchlings (n = 125) following replacement of the nesting material with a different lot. All adult birds appeared healthy, and hatchability was not significantly affected, but hatchlings became lethargic and dyspneic after a day of hatch. At necropsy, dark wet lungs were found in the hatchlings. Case 2 was submitted by a show-roller pigeon breeder. In this case, the owner reported lower hatchability, and all hatchlings (approximately 100) died within 2 days of hatching with clinical signs similar to the first case. Necropsy did not reveal any significant findings. For both cases, nesting materials were screened for toxic compounds using gas chromatography-mass spectrometry. Toluene-2,4-diisocyanate (approximately 190-290 ppm) and 4,4'-methylene diphenyl diisocyanate (unquantified) were detected in the nesting pads. While there is very limited information on toxicosis in birds, there are reports of inhalant exposure of diisocyanates causing pulmonary edema and death in various mammalian species. Although cause-effect relationship of mortality and the nesting material was not established in the present cases, the presence of toxic compounds in the nesting materials is a cause for concern. Further investigation is needed to determine the prevalence and toxicity of diisocyanates-contaminated nesting material in avian species.

The Combined Influence of Air Pollution and Home Learning Environment on Early Cognitive Skills in Children

PubMed Central

Stingone, Jeanette A.

2017-01-01

Cognitive skills are one component of school readiness that reflect a child’s neurodevelopment and are influenced by environmental and social factors. Most studies assess the impact of these factors individually, without taking into consideration the complex interactions of multiple factors. The objective of this study was to examine the joint association of markers of environmental pollution and of social factors on early cognitive skills in an urban cohort of children. For this, we chose isophorone in ambient air as a marker of industrial air pollution. Low quality home learning environments was chosen as a marker of the social factors contributing to cognitive development. Using a subpopulation from the Early Childhood Longitudinal Study, Birth Cohort (N = 4050), isophorone exposure was assigned using the 2002 National Air Toxics Assessment. Home learning environment was assessed with a modified version of the Home Observation for Measurement of the Environment (HOME) Inventory, and standardized math assessment scores were used as a measure of early cognitive skills. Multiple linear regression was used to estimate the effect of both exposures on math scores. After adjustment for confounders, children living in areas with ambient isophorone in the upper quintile of exposure (>0.49 ng/m3) had math scores that were 1.63 points lower than their less exposed peers [95% CI: −2.91, −0.34], and children with lower HOME scores (at or below 9 out of 12) had math scores that were 1.20 points lower than children with better HOME scores [95% CI: −2.30, −0.10]. In adjusted models accounting for identified confounders and both exposures of interest, both high isophorone exposure and low HOME score remained independently associated with math scores [−1.48, 95% CI: −2.79, −0.18; −1.05, 95% CI: −2.15, 0.05, respectively]. There was no statistical evidence of interaction between the two exposures, although children with both higher isophorone exposure and a low HOME score had a decrement in math scale score beyond the additive effect of each exposure. This was primarily observed among male children. These findings suggest that aspects of both the physical and social environments are independently associated with children’s early cognitive skills. Future research aiming to improve children’s early cognitive skills and subsequent school readiness should address both domains. PMID:29072589

The Combined Influence of Air Pollution and Home Learning Environment on Early Cognitive Skills in Children.

PubMed

Lett, Lanair A; Stingone, Jeanette A; Claudio, Luz

2017-10-26

Cognitive skills are one component of school readiness that reflect a child's neurodevelopment and are influenced by environmental and social factors. Most studies assess the impact of these factors individually, without taking into consideration the complex interactions of multiple factors. The objective of this study was to examine the joint association of markers of environmental pollution and of social factors on early cognitive skills in an urban cohort of children. For this, we chose isophorone in ambient air as a marker of industrial air pollution. Low quality home learning environments was chosen as a marker of the social factors contributing to cognitive development. Using a subpopulation from the Early Childhood Longitudinal Study, Birth Cohort (N = 4050), isophorone exposure was assigned using the 2002 National Air Toxics Assessment. Home learning environment was assessed with a modified version of the Home Observation for Measurement of the Environment (HOME) Inventory, and standardized math assessment scores were used as a measure of early cognitive skills. Multiple linear regression was used to estimate the effect of both exposures on math scores. After adjustment for confounders, children living in areas with ambient isophorone in the upper quintile of exposure (>0.49 ng/m³) had math scores that were 1.63 points lower than their less exposed peers [95% CI: -2.91, -0.34], and children with lower HOME scores (at or below 9 out of 12) had math scores that were 1.20 points lower than children with better HOME scores [95% CI: -2.30, -0.10]. In adjusted models accounting for identified confounders and both exposures of interest, both high isophorone exposure and low HOME score remained independently associated with math scores [-1.48, 95% CI: -2.79, -0.18; -1.05, 95% CI: -2.15, 0.05, respectively]. There was no statistical evidence of interaction between the two exposures, although children with both higher isophorone exposure and a low HOME score had a decrement in math scale score beyond the additive effect of each exposure. This was primarily observed among male children. These findings suggest that aspects of both the physical and social environments are independently associated with children's early cognitive skills. Future research aiming to improve children's early cognitive skills and subsequent school readiness should address both domains.

Toluene Diisocyanates (TDI) Action Plan

EPA Pesticide Factsheets

This Action Plan addresses the use of toluene diisocyanate (TDI) and related compounds in products that may result in consumer and general population exposures, particularly in or around buildings, including homes and schools.

The effect of compound 48/80 on contractions induced by toluene diisocyanate in isolated guinea-pig bronchus.

PubMed

Mapp, C E; Boniotti, A; Papi, A; Chitano, P; Coser, E; Di Stefano, A; Saetta, M; Ciaccia, A; Fabbri, L M

1993-06-01

We have investigated the ability of compound 48/80 and of histamine H1 and H2 receptor antagonists to inhibit toluene diisocyanate-induced contractions in isolated guinea-pig bronchi. Compound 48/80 (100 micrograms/ml) significantly inhibited toluene diisocyanate-induced contractions. By contrast, the two histamine H1 and H2 receptor antagonists, chlorpheniramine (10 microM) and cimetidine, (10 microM) did not affect toluene diisocyanate-induced contractions, but significantly inhibited contractions induced by exogenously applied histamine (100 microM) and by 48/80. We investigated which mechanisms 48/80 used to inhibit toluene diisocyanate-induced contractions, paying particular attention to the possible involvement of capsaicin-sensitive primary afferents. In vitro capsaicin desensitization (10 microM for 30 min followed by washing) significantly reduced compound 48/80-induced contractions. A capsaicin-resistant component of contraction was also evident. Ruthenium red (3 microM), an inorganic dye which acts as a selective functional antagonist of capsaicin, did not affect 48/80-induced contraction. MEN 10,207 (Tyr5,D-Trp6,8,9,Arg10)-neurokinin A (4-10) (3 microM) a selective antagonist of NK2-tachykinin receptors significantly reduced 48/80-induced contractions. These results show that compound 48/80 inhibits toluene diisocyanate-induced contractions in isolated guinea-pig bronchi. It is likely that two mechanisms are involved in the inhibition: (1) the release of mediators other than histamine by mast cells, (2) an effect of 48/80 on sensory nerves.

Fate and potential environmental effects of methylenediphenyl diisocyanate and toluene diisocyanate released into the atmosphere.

PubMed

Tury, Bernard; Pemberton, Denis; Bailey, Robert E

2003-01-01

Information from a variety of sources has been collected and summarized to facilitate an overview of the atmospheric fate and potential environmental effects of emissions of methylenediphenyl diisocyanate (MDI) or toluene diisocyanate (TDI) to the atmosphere. Atmospheric emissions of both MDI and TDI are low, both in terms of concentration and mass, because of their low volatility and the need for careful control over all aspects of their lifecycle from manufacture through disposal. Typical emission losses for TDI are 25 g/t of TDI used in slabstock foam production. MDI emission losses are lower, often less than 1 g/t of MDI used. Dispersion modeling predicts that concentrations at the fenceline or beyond are very low for typical releases. Laboratory studies show that TDI (and by analogy MDI) does not react with water in the gas phase at a significant rate. The primary degradation reaction of these aromatic diisocyanates in the atmosphere is expected to be oxidation by OH radicals with an estimated half-life of one day. Laboratory studies also show that this reaction is not expected to result in increased ground-level ozone accumulation.

Methylene Diphenyl Diisocyanate (MDI) And Related Compounds

EPA Pesticide Factsheets

This document addresses the use of methylene diphenyl diisocyanate (MDI) and related compounds (See Appendix 1) in products that may result in consumer and general population exposures, particularly in or around buildings, including homes and schools.

40 CFR 469.22 - Specialized definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Trichloroethane methylene chloride naphthalene 2 Nitrophenol phenol bis (2-ethylhexyl) phthalate...-butyl phthalate anthracene 1,2 Diphenylhydrazine isophorone butyl benzyl pthalate 1,1 Dichloroethylene 2...

40 CFR 469.22 - Specialized definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Trichloroethane methylene chloride naphthalene 2 Nitrophenol phenol bis (2-ethylhexyl) phthalate...-butyl phthalate anthracene 1,2 Diphenylhydrazine isophorone butyl benzyl pthalate 1,1 Dichloroethylene 2...

Sensitization and cross-reactivity patterns of contact allergy to diisocyanates and corresponding amines: investigation of diphenylmethane-4,4'-diisocyanate, diphenylmethane-4,4'-diamine, dicyclohexylmethane-4,4'-diisocyanate, and dicylohexylmethane-4,4'-diamine.

PubMed

Hamada, Haneen; Bruze, Magnus; Zimerson, Erik; Isaksson, Marléne; Engfeldt, Malin

2017-10-01

Isocyanates are used in polyurethane production. Dermal exposure to isocyanates can induce contact allergy. The most common isocyanate is diphenylmethane diisocyanate used for industrial purposes. The isomer diphenylmethane-4,4'-diisocyanate (4,4'-MDI) is used in patch testing. Diphenylmethane-4,4'-diamine (4,4'-MDA) is its corresponding amine. Concurrent reactions to 4,4'-MDI and 4,4'-MDA have been reported, as have concurrent reactions to 4,4'-MDI and dicyclohexylmethane-4,4'-diisocyanate (4,4'-DMDI). To investigate the sensitization capacities and the cross-reactivity of 4,4'-MDI, 4,4'-MDA, 4,4'-DMDI, and dicyclohexylmethane-4,4'-diamine (4,4'-DMDA). The guinea-pig maximization test (GPMT) was used. The GPMT showed sensitizing capacities for all investigated substances: 4,4'-MDI, 4,4'-MDA, 4,4'-DMDI, and 4,4'-DMDA (all p < 0.001). 4,4'-MDI-sensitized animals showed cross-reactivity to 4,4'-MDA (p < 0.001) and 4,4'-DMDI (all p < 0.05). 4,4'-MDA-sensitized animals showed cross-reactivity to 4,4'-DMDA (p = 0.008). All of the investigated substances were shown to be strong sensitizers. Animals sensitized to 4,4'-MDI showed cross-reactivity to 4,4'-MDA and 4,4'-DMDI, supporting previous findings in the literature. The aromatic amine 4,4'-MDA showed cross-reactivity to the aliphatic amine 4,4'-DMDA. © 2017 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.

Melissopalynological and volatile analysis of honeys from Corsican Arbutus unedo habitat.

PubMed

Yang, Yin; Battesti, Marie-José; Costa, Jean; Paolini, Julien

2014-10-01

Thirty Corsican "autumn maquis" honeys were characterized by the typical combination of autumnal taxa: Arbutus unedo, Hedera helix, Smilax aspera, Rosmarinus officinalis, and two Asteraceae pollen forms. Corsican origin was characterized by the diversity of the taxa's biogeographical origins and significant presence of Castanea sativa and Quercus sp. Volatile fractions of "autumn maquis" honeys were dominated by isophorone and 3,4,5-trimethylphenol. The latter is reported in A. unedo honey for the first time. Otherwise, both A. unedo flower and "autumn maquis" honeys exhibited high contents of isophorone derivatives. H. helix honey exhibited phenylacetaldehyde, benzyl nitrile, 3-hydroxy-4-phenylbutan-2-one and nonanal as major compounds, which were scarcely represented in the studied "autumn maquis" honey samples.

1,6-Hexamethylene diisocyanate

Integrated Risk Information System (IRIS)

1,6 - Hexamethylene diisocyanate ; CASRN 822 - 06 - 0 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for

PULMONARY HYPERRESPONSIVENESS FOLLOWING DERMAL EXPOSURE TO SELECTED DIISOCYANATES

EPA Science Inventory

PULMONARY HYPERRESPONSIVENESS FOLLOWING DERMAL EXPOSURE TO SELECTED DIISOCYANATES

M.J.K. Selgrade, E.H. Boykin, N.H. Coates, D.L. Doerfler, S.H. Gavett
Experimental Toxicology Div., National Health and Environmental Research Laboratory, Office of Research and Developmen...

Water-free synthesis of polyurethane foams using highly reactive diisocyanates derived from 5-hydroxymethylfurfural.

PubMed

Neumann, Christopher N D; Bulach, Winfried D; Rehahn, Matthias; Klein, Roland

2011-09-01

This paper reports on the synthesis of a new highly reactive diisocyanate monomer based on hydroxymethylfurfural. It further describes its catalyst-free conversion to linear-chain thermoplastic polyurethanes as well as to cross-linked polyurethane foams. In addition, a novel strategy for the synthesis of polyurethane foams without the necessity of using water is developed. Nitrogen is utilized herein as blowing agent which is formed during Curtius rearrangement of a new furan based carboxylic azide into its corresponding diisocyanate. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

40 CFR 469.22 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... trichloroethylene 2 Chlorophenol 2,4 Dichlorophenol 4 Nitrophenol pentachlorophenol di-n-butyl phthalate anthracene 1,2 Diphenylhydrazine isophorone butyl benzyl pthalate 1,1 Dichloroethylene 2,4,6 Trichlorophenol...

40 CFR 469.22 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... trichloroethylene 2 Chlorophenol 2,4 Dichlorophenol 4 Nitrophenol pentachlorophenol di-n-butyl phthalate anthracene 1,2 Diphenylhydrazine isophorone butyl benzyl pthalate 1,1 Dichloroethylene 2,4,6 Trichlorophenol...

Methylene Diphenyl Diisocyanate (monomeric MDI) and polymeric MDI (PMDI)

Integrated Risk Information System (IRIS)

TOXICOLOGICAL REVIEW of METHYLENE DIPHENYL DIISOCYANATE ( MDI ) ( CAS No . 101 - 68 - 8 and 9016 - 87 - 9 ) In Support of Summary Information on the Integrated Risk Information System ( IRIS ) February 1998 U.S . ENVIRONMENTAL PROTECTION AGENCY WASHINGTON , DC TABLE OF CONTENTS TOXICOLOGICAL REV

40 CFR 721.2540 - Diphenylmethane diisocyanate (MDI) modified.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.2540 Diphenylmethane diisocyanate (MDI) modified. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a...

Catalysis beyond frontier molecular orbitals: Selectivity in partial hydrogenation of multi-unsaturated hydrocarbons on metal catalysts

PubMed Central

Liu, Wei; Jiang, Yingda; Dostert, Karl-Heinz; O’Brien, Casey P.; Riedel, Wiebke; Savara, Aditya; Schauermann, Swetlana; Tkatchenko, Alexandre

2017-01-01

The mechanistic understanding and control over transformations of multi-unsaturated hydrocarbons on transition metal surfaces remains one of the major challenges of hydrogenation catalysis. To reveal the microscopic origins of hydrogenation chemoselectivity, we performed a comprehensive theoretical investigation on the reactivity of two α,β-unsaturated carbonyls—isophorone and acrolein—on seven (111) metal surfaces: Pd, Pt, Rh, Ir, Cu, Ag, and Au. In doing so, we uncover a general mechanism that goes beyond the celebrated frontier molecular orbital theory, rationalizing the C═C bond activation in isophorone and acrolein as a result of significant surface-induced broadening of high-energy inner molecular orbitals. By extending our calculations to hydrogen-precovered surface and higher adsorbate surface coverage, we further confirm the validity of the “inner orbital broadening mechanism” under realistic catalytic conditions. The proposed mechanism is fully supported by our experimental reaction studies for isophorone and acrolein over Pd nanoparticles terminated with (111) facets. Although the position of the frontier molecular orbitals in these molecules, which are commonly considered to be responsible for chemical interactions, suggests preferential hydrogenation of the C═O double bond, experiments show that hydrogenation occurs at the C═C bond on Pd catalysts. The extent of broadening of inner molecular orbitals might be used as a guiding principle to predict the chemoselectivity for a wide class of catalytic reactions at metal surfaces. PMID:28782033

2,4-/2,6-Toluene diisocyanate mixture (TDI)

Integrated Risk Information System (IRIS)

2,4 - / 2,6 - Toluene diisocyanate mixture ( TDI ) ; CASRN 26471 - 62 - 5 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Haz

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Standards for slabstock flexible polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam...

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 12 2012-07-01 2011-07-01 true Standards for slabstock flexible polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam...

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 11 2011-07-01 2011-07-01 false Standards for slabstock flexible polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam...

Synthesis of renewable high-density fuel with isophorone.

PubMed

Wang, Wei; Liu, Yanting; Li, Ning; Li, Guangyi; Wang, Wentao; Wang, Aiqin; Wang, Xiaodong; Zhang, Tao

2017-07-21

1,1,3-Trimethyl-5-(2,4,4-trimethylcyclohexyl)cyclohexane, a renewable high density fuel, was first produced in a high overall carbon yield (~70%) with isophorone which can be derived from hemicellulose. The synthetic route used this work contains three steps. In the first step, 3,3,5-trimethylcyclohexanone was synthesized by the selective hydrogenation of isophorone. Among the investigated catalysts, the Pd/C exhibited the highest activity and selectivity. Over this catalyst, a high carbon yield (99.0%) of 3,3,5-trimethylcyclohexanone was achieved under mild conditions (298 K, 2 MPa H 2 , 1 h). In the second step, 3,5,5-trimethyl-2-(3,3,5-trimethylcyclohexylidene)cyclohexanone was produced in a high carbon yield (76.4%) by the NaOH catalyzed self-aldol condensation of 3,3,5-trimethylcyclohexanone which was carried out in a round bottom flask attached to the Dean-Stark apparatus. In the third step, the 3,5,5-trimethyl-2-(3,3,5-trimethylcyclohexylidene)cyclohexanone was hydrodeoxygenated under solvent-free conditions. High carbon yield (93.4%) of 1,1,3-trimethyl-5-(2,4,4-trimethylcyclohexyl)cyclohexane was obtained over the Ni/SiO 2 catalyst. The 1,1,3-trimethyl-5-(2,4,4-trimethylcyclohexyl)cyclohexane as obtained has a density of 0.858 g mL -1 and a freezing point of 222.2 K. As a potential application, it can be blended into conventional fuels (such as RP-1, RG-1, etc.) for rocket propulsion.

40 CFR 721.10693 - Diphenylmethane diisocyanate polymer with alkanoic diacid and alkanediol (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Diphenylmethane diisocyanate polymer... polymer with alkanoic diacid and alkanediol (generic). (a) Chemical substance and significant new uses... polymer with alkanoic diacid and alkanediol (PMN P-13-338) is subject to reporting under this section for...

Compatibility of melt-processed zein blends with methylenediphenyl 4,4'-diisocyanate-thermal, mechanical and physical properties

USDA-ARS?s Scientific Manuscript database

Corn zein was melt-processed with methylenediphenyl 4,4'-diisocyanate (MDI) using triethylamine (TEA) as catalyst. The objective is to construct a melt-processed, compatible blend of zein with MDI that can be used as a building block for generating bio-based thermoplastics. The impact of cross-linki...

Waterborne Polymeric Films.

DTIC Science & Technology

1981-02-01

polymer of neopentyl glycol (NPC) and isophoronediisocyanate (IPDI) as an example: CH 3 0 CH3 0 CH- HO !Ch,,C h OCNH CH.NHCO, HCCH.OH CIF CH- Groun...copolymer of isophoronediisocyanate with neopentyl glycol and dimethylolpropionic acid. And the solibilitv parameter calculations must include this...copolymer of isophoronediiisocyanate with a diol mixture of 85 inol percent neopentyl glycol and 15 inol percent dimethyl- olpropionic acid. 0 0 0 it 0

40 CFR Table 8 to Subpart Ffff of... - Soluble Hazardous Air Pollutants

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Dinitrotoluene (2,4) 121142 7. Dioxane (1,4) 123911 8. Ethylene glycol dimethyl ether 110714 9. Ethylene glycol monobutyl ether acetate 112072 10. Ethylene glycol monomethyl ether acetate 110496 11. Isophorone 78591 12...

Advanced Fast Curing Adhesives for Adverse Conditions

DTIC Science & Technology

2007-07-01

experimentation. The catalyst is composed of 50% phthalate esters and 50% trivalent organic chromium complexes (15). 2.3 Aluminum Lap Plates...adhesives (2). Tape adhesives never provide weld - strength bonds and often have low tackiness when used underwater. Ultraviolet and visible light curable...diisocyanate and diphenylmethane-4, 4 diisocyanate (MDI) (12). The low viscosity ethyl cyanoacrylate Scotch- Weld CA40 was obtained from 3M of St

40 CFR Table 4 to Subpart F of... - Organic Hazardous Air Pollutants Subject to Cooling Tower Monitoring Requirements in § 63.104

Code of Federal Regulations, 2012 CFR

2012-07-01

... glycol dimethyl ether 111966 Diethyl sulfate 64675 Dimethylaniline (N,N-) 121697 Dimethylhydrazine (1,1... 67721 Hexane 110543 Isophorone 78591 Methanol 67561 Methyl bromide (Bromomethane) 74839 Methyl chloride...

40 CFR Table 9 to Subpart Ggg of... - Default Biorates for Soluble HAP

Code of Federal Regulations, 2010 CFR

2010-07-01

....178 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol dimethyl ether 0.364 Ethylene glycol monobutyl ether acetate 0.496 Ethylene glycol monomethyl ether acetate 0.159 Isophorone 0.598 Methanol a...

Protein adducts as biomarkers of exposure to aromatic diisocyanates in workers manufacturing polyurethane (PUR) foam.

PubMed

Säkkinen, Kirsi; Tornaeus, Jarkko; Hesso, Antti; Hirvonen, Ari; Vainio, Harri; Norppa, Hannu; Rosenberg, Christina

2011-04-01

This work was undertaken to investigate the usefulness of diisocyanate-related protein adducts in blood samples as biomarkers of occupational exposure to toluene diisocyanate (TDI; 2,4- and 2,6-isomers) and 4,4'-methylenediphenyl diisocyanate (MDI). Quantification of adducts as toluene diamines (TDAs) and methylenedianiline (MDA) was performed on perfluoroacylated derivatives by gas chromatography-mass spectrometry (GC-MS/MS) in negative chemical ionisation mode. TDI-derived adducts were found in 77% of plasma and in 59% of globin samples from exposed workers manufacturing flexible polyurethane foam. The plasma levels ranged from 0.003 to 0.58 nmol mL(-1) and those in globin from 0.012 to 0.33 nmol g(-1). The 2,6-isomer amounted to about two-thirds of the sum concentration of TDA isomers. MDI-derived adducts were detected in 3.5% of plasma and in 7% of globin samples from exposed workers manufacturing rigid polyurethane foam. A good correlation was found between the sum of TDA isomers in urine and that in plasma. The relationship between globin adducts and urinary metabolites was ambiguous. Monitoring TDI-derived TDA in plasma thus appears to be an appropriate method for assessing occupational exposure. Contrary to TDI exposure, adducts in plasma or globin were not useful in assessing workers' exposure to MDI. An important outcome of the study was that no amine-related adducts were detected in globin samples from TDI- or MDI-exposed workers, alleviating concerns that TDI or MDI might pose a carcinogenic hazard. Further studies are nevertheless required to judge whether diisocyanates per se could be such a hazard.

Carbon Nanofiber Incorporated Silica Based Aerogels with Di-Isocyanate Cross-Linking

NASA Technical Reports Server (NTRS)

Vivod, Stephanie L.; Meador, Mary Ann B.; Capadona, Lynn A.; Sullivan, Roy M.; Ghosn, Louis J.; Clark, Nicholas; McCorkle, Linda

2008-01-01

Lightweight materials with excellent thermal insulating properties are highly sought after for a variety of aerospace and aeronautic applications. (1) Silica based aerogels with their high surface area and low relative densities are ideal for applications in extreme environments such as insulators for the Mars Rover battery. (2) However, the fragile nature of aerogel monoliths prevents their widespread use in more down to earth applications. We have shown that the fragile aerogel network can be cross-linked with a di-isocyanate via amine decorated surfaces to form a conformal coating. (3) This coating reinforces the neck regions between secondary silica particles and significantly strengthens the aerogels with only a small effect on density or porosity. Scheme 1 depicts the cross-linking reaction with the di-isocyanate and exhibits the stages that result in polymer cross-linked aerogel monoliths.

Indoor air pollution evaluation with emphasize on HDI and biological assessment of HDA in the polyurethane factories.

PubMed

Mirmohammadi, Mirtaghi; Hakimi Ibrahim, M; Ahmad, Anees; Kadir, Mohd Omar Abdul; Mohammadyan, M; Mirashrafi, S B

2010-06-01

Today, many raw materials used in factories may have a dangerous effect on the physiological system of workers. One of them which is widely used in the polyurethane factories is diisocyanates. These compounds are widely used in surface coatings, polyurethane foams, adhesives, resins, elastomers, binders, and sealants. Exposure to diisocyanates causes irritation to the skin, mucous membranes, eyes, and respiratory tract. Hexamethylene diamine (HDA) is metabolite of hexamethylene diisocyanate (HDI). It is an excretory material by worker's urine who is exposed to HDI. Around 100 air samples were collected from five defined factories by midget impinger which contained dimethyl sulfoxide absorbent as a solvent and tryptamine as reagent. Samples were analyzed by high-performance liquid chromatography with EC\\UV detector using NIOSH 5522 method of sampling. Also, 50 urine samples collected from workers were also analyzed using William's biological analysis method. The concentration of HDI into all air samples were more than 88 microg/m(3), and they have shown high concentration of pollutant in the workplaces in comparison with NIOSH standard, and all of the workers' urine were contaminated by HDA. The correlation and regression test were used to obtain statistical model for HDI and HDA, which is useful for the prediction of diisocyanates pollution situation in the polyurethane factories.

40 CFR Table 1 to Subpart Eeee of... - Organic Hazardous Air Pollutants

Code of Federal Regulations, 2011 CFR

2011-07-01

... (N,N-) 121-69-7 Diethylene glycol monobutyl ether 112-34-5 Diethylene glycol monomethyl ether 111-77... Formaldehyde 50-00-0 Hexachloroethane 67-72-1 Hexane 110-54-3 Hydroquinone 123-31-9 Isophorone 78-59-1 Maleic...

40 CFR Table 1 to Subpart Eeee of... - Organic Hazardous Air Pollutants

Code of Federal Regulations, 2014 CFR

2014-07-01

... (N,N-) 121-69-7 Diethylene glycol monobutyl ether 112-34-5 Diethylene glycol monomethyl ether 111-77... Formaldehyde 50-00-0 Hexachloroethane 67-72-1 Hexane 110-54-3 Hydroquinone 123-31-9 Isophorone 78-59-1 Maleic...

40 CFR Table 1 to Subpart Eeee of... - Organic Hazardous Air Pollutants

Code of Federal Regulations, 2012 CFR

2012-07-01

... (N,N-) 121-69-7 Diethylene glycol monobutyl ether 112-34-5 Diethylene glycol monomethyl ether 111-77... Formaldehyde 50-00-0 Hexachloroethane 67-72-1 Hexane 110-54-3 Hydroquinone 123-31-9 Isophorone 78-59-1 Maleic...

40 CFR Table 1 to Subpart Eeee of... - Organic Hazardous Air Pollutants

Code of Federal Regulations, 2010 CFR

2010-07-01

... (N,N-) 121-69-7 Diethylene glycol monobutyl ether 112-34-5 Diethylene glycol monomethyl ether 111-77... Formaldehyde 50-00-0 Hexachloroethane 67-72-1 Hexane 110-54-3 Hydroquinone 123-31-9 Isophorone 78-59-1 Maleic...

40 CFR Table 1 to Subpart Eeee of... - Organic Hazardous Air Pollutants

Code of Federal Regulations, 2013 CFR

2013-07-01

... (N,N-) 121-69-7 Diethylene glycol monobutyl ether 112-34-5 Diethylene glycol monomethyl ether 111-77... Formaldehyde 50-00-0 Hexachloroethane 67-72-1 Hexane 110-54-3 Hydroquinone 123-31-9 Isophorone 78-59-1 Maleic...

40 CFR Table 1 to Subpart Ggggg of... - List of Hazardous Air Pollutants

Code of Federal Regulations, 2011 CFR

2011-07-01

....000 78591 Isophorone 0.506 58899 Lindane (all isomers) 1.000 67561 Methanol 0.855 74839 Methyl bromide... Fm 305 factors for some of the more common glycol 305 ethers can be obtained by contacting the Waste...

40 CFR Table 1 to Subpart Ggggg of... - List of Hazardous Air Pollutants

Code of Federal Regulations, 2010 CFR

2010-07-01

....000 78591 Isophorone 0.506 58899 Lindane (all isomers) 1.000 67561 Methanol 0.855 74839 Methyl bromide... Fm 305 factors for some of the more common glycol 305 ethers can be obtained by contacting the Waste...

Elucidation of the Dynamics for Hot-Spot Initiation at Nonuniform Interfaces of Highly Shocked Materials

DTIC Science & Technology

2011-12-07

with nonuniform interfaces plays an essential role in the interfacial instabilities in iner- tial confinement fusion (ICF), in shock-induced...involved in interfacial instabilities at the atomic scale, providing insights on such phenomenon. Thus ReaxFF provides the possibility of realistic...calculations was also performed on the IPDI and DOA to determine the charges and structures for the binder model. These QM results and model preparation

Elucidation of the Dynamics for Hot-Spot Initiation at Nonuniform Interfaces of Highly Shocked Materials

DTIC Science & Technology

2011-12-07

with nonuniform interfaces plays an essential role in the interfacial instabilities in iner- tial confinement fusion (ICF), in shock-induced...involved in interfacial instabilities at the atomic scale, providing insights on such phenomenon. Thus ReaxFF provides the possibility of realistic...on the IPDI and DOA to determine the charges and structures for the binder model. These QM results and model preparation procedure are provided as part

Molecular layer deposition of polyurethane-Polymerisation at the very contact to native aluminium and copper

NASA Astrophysics Data System (ADS)

Fug, Frank; Petry, Adrien; Jost, Hendrik; Ahmed, Aisha; Zamanzade, Mohammad; Possart, Wulff

2017-12-01

Thin layers of polyurethane monomers (diol, triol, diisocyanate) are deposited from gas phase onto native aluminium and copper surfaces. According to infrared external reflection absorption spectra both alcohols undergo only weak physical interactions with both metals. The diisocyanate on the other hand reveals resistance against desorption and rich new spectral features indicate strong adhesion. Preparation of urethane layers by sequential deposition of diisocyanate and diol yields urethane linkages. Urethane is formed faster on Cu than on Al. Scanning force microscopy reveals heterogeneous layers with metal dependent morphology. They show poor resistance against tetrahydrofuran rinsing i.e. most part of the formed urethane containing molecules are removed. Nevertheless, a residue of molecules sticks on the metal. It contains strongly adsorbed isocyanates and few isocyanate units which are bonded to diol units via urethane links. Further improvement of the molecular layer deposition is necessary to achieve well-crosslinked polyurethane layers.

40 CFR Table 2 to Subpart Jj of... - List of Volatile Hazardous Air Pollutants

Code of Federal Regulations, 2014 CFR

2014-07-01

...-Dichloropropene 542756 Diethanolamine 111422 N,N-Dimethylaniline 121697 Diethyl sulfate 64675 3,3... 79447 N,N-Dimethylformamide 68122 1,1-Dimethylhydrazine 57147 Dimethyl phthalate 131113 Dimethyl sulfate... Hexamethylphosphoramide 680319 Hexane 110543 Hydrazine 302012 Hydroquinone 123319 Isophorone 78591 Maleic anhydride 108316...

40 CFR Table 8 to Subpart Ggg of... - Fraction Measured (Fm) for HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2010 CFR

2010-07-01

... Dichloropropene (1,3-) 542756 1.00 Diethyl sulfate 64675 0.0025 Dimethyl sulfate 77781 0.086 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.88 Hexachloroethane 67721 0.50 Hexane 110543 1.00 Isophorone 78591 0.47 Methanol 67561 0...

40 CFR Table 8 to Subpart Ggg of... - Fraction Measured (Fm) for HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2011 CFR

2011-07-01

... Dichloropropene (1,3-) 542756 1.00 Diethyl sulfate 64675 0.0025 Dimethyl sulfate 77781 0.086 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.88 Hexachloroethane 67721 0.50 Hexane 110543 1.00 Isophorone 78591 0.47 Methanol 67561 0...

40 CFR Table 8 to Subpart Ggg of... - Fraction Measured (Fm) for HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2012 CFR

2012-07-01

... Dichloropropene (1,3-) 542756 1.00 Diethyl sulfate 64675 0.0025 Dimethyl sulfate 77781 0.086 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.88 Hexachloroethane 67721 0.50 Hexane 110543 1.00 Isophorone 78591 0.47 Methanol 67561 0...

40 CFR Table 8 to Subpart Ggg of... - Fraction Measured (Fm) for HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2014 CFR

2014-07-01

... Dichloropropene (1,3-) 542756 1.00 Diethyl sulfate 64675 0.0025 Dimethyl sulfate 77781 0.086 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.88 Hexachloroethane 67721 0.50 Hexane 110543 1.00 Isophorone 78591 0.47 Methanol 67561 0...

40 CFR Table 8 to Subpart Ggg of... - Fraction Measured (Fm) for HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2013 CFR

2013-07-01

... Dichloropropene (1,3-) 542756 1.00 Diethyl sulfate 64675 0.0025 Dimethyl sulfate 77781 0.086 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.88 Hexachloroethane 67721 0.50 Hexane 110543 1.00 Isophorone 78591 0.47 Methanol 67561 0...

40 CFR Table 2 to Subpart Jj of... - List of Volatile Hazardous Air Pollutants

Code of Federal Regulations, 2013 CFR

2013-07-01

...-Dichloropropene 542756 Diethanolamine 111422 N,N-Dimethylaniline 121697 Diethyl sulfate 64675 3,3... 79447 N,N-Dimethylformamide 68122 1,1-Dimethylhydrazine 57147 Dimethyl phthalate 131113 Dimethyl sulfate... Hexamethylphosphoramide 680319 Hexane 110543 Hydrazine 302012 Hydroquinone 123319 Isophorone 78591 Maleic anhydride 108316...

40 CFR Table 2 to Subpart Jj of... - List of Volatile Hazardous Air Pollutants

Code of Federal Regulations, 2012 CFR

2012-07-01

...-Dichloropropene 542756 Diethanolamine 111422 N,N-Dimethylaniline 121697 Diethyl sulfate 64675 3,3... 79447 N,N-Dimethylformamide 68122 1,1-Dimethylhydrazine 57147 Dimethyl phthalate 131113 Dimethyl sulfate... Hexamethylphosphoramide 680319 Hexane 110543 Hydrazine 302012 Hydroquinone 123319 Isophorone 78591 Maleic anhydride 108316...

Insensitive explosive composition and method of fracturing rock using an extrudable form of the composition

DOEpatents

Davis, Lloyd L

2013-11-05

Insensitive explosive compositions were prepared by reacting di-isocyanate and/or poly-isocyanate monomers with an explosive diamine monomer. Prior to a final cure, the compositions are extrudable. The di-isocyanate monomers tend to produce tough, rubbery materials while polyfunctional monomers (i.e. having more than two isocyanate groups) tend to form rigid products. The extrudable form of the composition may be used in a variety of applications including rock fracturing.

Insensitive explosive composition and method of fracturing rock using an extrudable form of the composition

DOEpatents

Davis, Lloyd L.

2015-07-28

Insensitive explosive compositions were prepared by reacting di-isocyanate and/or poly-isocyanate monomers with an explosive diamine monomer. Prior to a final cure, the compositions are extrudable. The di-isocyanate monomers tend to produce tough, rubbery materials while polyfunctional monomers (i.e. having more than two isocyanate groups) tend to form rigid products. The extrudable form of the composition may be used in a variety of applications including rock fracturing.

Evaluation of self-reported skin problems among workers exposed to toluene diisocyanate (TDI) at a foam manufacturing facility.

PubMed

Daftarian, Helga S; Lushniak, Boris D; Reh, Christopher M; Lewis, Daniel M

2002-12-01

Toluene diisocyanate, or TDI (CAS 584-84-9) is a well-known asthmagen and respiratory irritant. TDI is also known for its ability to irritate the skin and mucous membranes. To further investigate the dermal effects of TDI, NIOSH investigators conducted a cross-sectional study at a flexible foam manufacturing plant. A total of 114 workers participated in the study. Participants completed a medical questionnaire, provided blood for antibody testing to TDI and other allergens, and a subset of participants reporting skin symptoms underwent skin patch testing to a standard diisocyanate panel. Production line workers were more than twice as likely to report skin problems as those working in nonproduction areas (PRR = 2.66; 95% CI = 1.14-16.32; P = 0.02). Age, gender and duration of employment at the plant were comparable among participants working in production and nonproduction areas. Of the 100 participants who provided blood samples for antibody testing, specific IgG antibody to TDI was detected in two individuals, and none of the samples demonstrated specific IgE antibody to TDI. Of the 26 workers who underwent skin patch testing, none developed reactions to the diisocyanate allergens. These results suggest that the skin symptoms among study participants represent an irritant rather than an immunologic reaction to TDI, or to an unidentified allergen present in the foam.

Combustion Mechanisms of Wide Distribution Propellants

DTIC Science & Technology

1988-06-01

trimodal propellants were formulated. Each set contains an HTPB binder and duplicate formulations were made with either a IPDI or a DDI curative. The...Distinctive Mechanisms Previous studies [12,131 have shown that HTPB * propellants with wide AP distributions burn at rates much different than predictions...propellants. 17 .- = i.= i i i il =.. .l=limim mll ili= =.l i@ w. -’- 87% 400/20/ 3 MICRON,AP/ HTPB PROPELLANT 2.0 Z -1.0 --- 0--.-7- 0 CALCULATIONO0

Analytical approaches to identify potential migrants in polyester-polyurethane can coatings.

PubMed

Louise Bradley, Emma; Driffield, Malcolm; Guthrie, James; Harmer, Nick; Thomas Oldring, Peter Kenneth; Castle, Laurence

2009-12-01

The safety of a polyester-polyurethane can coating has been assessed using a suite of complementary analytical methods to identify and estimate the concentrations of potential chemical migrants. The polyester was based on phthalic acids and aliphatic diols. The polyisocyanate cross-linking agent was 1-isocyanato-3-isocyanatomethyl-3,5,5-trimethyl cyclohexane homopolymer (IPDI) blocked with methylethylketone oxime (MEKO) to make a one-part formulation. The overall migrate, obtained using solvent extraction of cured films, comprised almost completely of 12 cyclic and one linear polyester oligomer up to molecular weight 800 and containing up to six monomer units. These 13 oligomers covered a total of 28 isomeric forms. Other minor components detected were plasticisers and surfactants as well as impurities present in the starting materials. There was no detectable residue of either the blocked isocyanate (<0.01 microg/dm(2)) used as the starting substance or the unblocked isocyanate (<0.02 microg/dm(2)). The level of extractable IPDI was used as an indicator of the completeness of cure in experimental coatings. These studies revealed that there was an influence of time, temperature and catalyst content. Polymerisation was also influenced by the additives used and by the ageing of the wet coating formulation over several months. These studies allow parameters to be specified to ensure that commercial production coatings receive a full cure giving low migration characteristics.

N-Acetyltransferase 2 Genotypes Are Associated With Diisocyanate-Induced Asthma.

PubMed

Yucesoy, Berran; Kissling, Grace E; Johnson, Victor J; Lummus, Zana L; Gautrin, Denyse; Cartier, André; Boulet, Louis-Philippe; Sastre, Joaquin; Quirce, Santiago; Tarlo, Susan M; Cruz, Maria-Jesus; Munoz, Xavier; Luster, Michael I; Bernstein, David I

2015-12-01

To investigate whether genetic variants of N-acetyltransferase (NAT) genes are associated with diisocyanate asthma (DA). The study population consisted of 354 diisocyanate-exposed workers. Genotyping was performed using a 5'-nuclease polymerase chain reaction assay. The NAT2 rs2410556 and NAT2 rs4271002 variants were significantly associated with DA in the univariate analysis. In the first logistic regression model comparing DA+ and asymptomatic worker groups, the rs2410556 (P = 0.004) and rs4271002 (P < 0.001) single nucleotide polymorphisms and the genotype combination, NAT2 rs4271002*NAT1 rs11777998, showed associations with DA risk (P = 0.014). In the second model comparing DA+ and DA- groups, NAT2 rs4271002 variant and the combined genotype, NAT1 rs8190845*NAT2 rs13277605, were significantly associated with DA risk (P = 0.022, P = 0.036, respectively). These findings suggest that variations in the NAT2 gene and their interactions contribute to DA susceptibility.

40 CFR Table 9 to Subpart G of... - Organic HAP's Subject to the Wastewater Provisions for Process Units at New and Existing Sources...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (1,3-) 542756 0.99 Diethyl sulfate 64675 0.90 Dimethyl sulfate 77781 0.53 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.99 Hexachloroethane 67721 0.99 Hexane 110543 0.99 Isophorone 78591 0.60 Methanol 67561 0...

40 CFR Table 9 to Subpart G of... - Organic HAP's Subject to the Wastewater Provisions for Process Units at New and Existing Sources...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (1,3-) 542756 0.99 Diethyl sulfate 64675 0.90 Dimethyl sulfate 77781 0.53 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.99 Hexachloroethane 67721 0.99 Hexane 110543 0.99 Isophorone 78591 0.60 Methanol 67561 0...

40 CFR Table 9 to Subpart G of... - Organic HAP's Subject to the Wastewater Provisions for Process Units at New and Existing Sources...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (1,3-) 542756 0.99 Diethyl sulfate 64675 0.90 Dimethyl sulfate 77781 0.53 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.99 Hexachloroethane 67721 0.99 Hexane 110543 0.99 Isophorone 78591 0.60 Methanol 67561 0...

40 CFR Table 9 to Subpart G of... - Organic HAP's Subject to the Wastewater Provisions for Process Units at New and Existing Sources...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (1,3-) 542756 0.99 Diethyl sulfate 64675 0.90 Dimethyl sulfate 77781 0.53 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.99 Hexachloroethane 67721 0.99 Hexane 110543 0.99 Isophorone 78591 0.60 Methanol 67561 0...

40 CFR Table 9 to Subpart G of... - Organic HAP's Subject to the Wastewater Provisions for Process Units at New and Existing Sources...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (1,3-) 542756 0.99 Diethyl sulfate 64675 0.90 Dimethyl sulfate 77781 0.53 Dimethylaniline (N,N... Hexachlorobutadiene 87683 0.99 Hexachloroethane 67721 0.99 Hexane 110543 0.99 Isophorone 78591 0.60 Methanol 67561 0...

Polyurethane Binder Systems for Polymer Bonded Explosives

DTIC Science & Technology

2006-12-01

Propulsion (2005), Santiago , Chile . 8. Huang, C.-C., Hwu, W.-H., Cheng, C.-S., Shyy, I.-N., and Yang, K.-K., Study on Thermal Decomposition of Composite...water or amines to form ureas (Figure 2). R NCO R N C O H+ H2O O H R NH2 - CO2 R NCO R N C O NR’ H H ureaamine Figure 2. Reaction of an isocyanate...Monoisocyanates are present as impurities in low concentration in most diisocyanates. Table 1. Common diisocyanates Isocyanate Structure B.p. (ºC

Quantification of annular dilatation and papillary muscle separation in functional mitral regurgitation: role of anterior mitral leaflet length as reference.

PubMed

Jorapur, Vinod; Voudouris, Apostolos; Lucariello, Richard J

2005-07-01

We hypothesized that anterior mitral leaflet length (ALL) does not differ significantly between normal subjects and patients with functional mitral regurgitation (FMR) and hence may be used as a reference measurement to quantify annular dilatation and papillary muscle separation. We prospectively studied 50 controls, 15 patients with systolic left ventricular dysfunction (LVD) with significant FMR, and 15 patients with LVD without significant FMR. Significant MR was defined as an effective regurgitant orifice area > or = 0.2 cm2 as measured by the flow convergence method. Annular diameter, interpapillary distance, and ALL were measured, and the following ratios were derived: annular diameter indexed to ALL (ADI) and interpapillary distance indexed to ALL (IPDI). There was no significant difference in ALL among the three groups. The mean ADI was 1.26 times controls in patients with LVD without significant FMR compared to 1.33 times controls in patients with LVD with significant FMR (P = 0.06, no significant difference between groups). The mean IPDI was 1.42 times controls in patients with LVD without significant FMR compared to 2.1 times controls in patients with LVD with significant FMR (P < 0.0001, significant difference between groups). There was no significant difference in ALL between controls and patients with LVD. ALL can be used as a reference measurement to quantify annular dilatation and papillary muscle separation in patients with FMR. Interpapillary distance but not annular diameter indexed to ALL correlates with severity of FMR.

Occupational exposure to diisocyanates in polyurethane foam factory workers.

PubMed

Świerczyńska-Machura, Dominika; Brzeźnicki, Sławomir; Nowakowska-Świrta, Ewa; Walusiak-Skorupa, Jolanta; Wittczak, Tomasz; Dudek, Wojciech; Bonczarowska, Marzena; Wesolowski, Wiktor; Czerczak, Sławomir; Pałczyński, Cezary

2015-01-01

The aim of the study was to evaluate health effects of occupational exposure to diisocyanates (DIC) among polyurethane foam products factory workers. Thirty workers had a physical examination, skin prick tests with common allergens, allergen-specific immunoglobulin E (IgE) antibodies to diisocyanates and pulmonary function tests. Concentrations of selected isocyanates in the workplace air samples as well as concentration of their metabolites in the urine samples collected from the workers of the plant were determined. The most frequent work-related symptoms reported by the examined subjects were rhinitis and skin symptoms. Sensitization to at least 1 common allergen was noted in 26.7% of the subjects. Spirometry changes of bronchial obstruction of a mild degree was observed in 5 workers. The specific IgE antibodies to toluene diisocyanate (TDI) and 4,4'-methylenebis(phenyl isocyanate) (MDI) were not detected in any of the patients' serum. Cellular profiles of the collected induced sputum (ISP) did not reveal any abnormalities. Air concentrations of TDI isomers ranged 0.2-58.9 μg/m3 and in 7 cases they exceeded the Combined Exposure Index (CEI) value for those compounds. Concentrations of TDI metabolites in post-shift urine samples were significantly higher than in the case of pre-shift urine samples and in 6 cases they exceeded the British Biological Monitoring Guidance Value (BMGV - 1 μmol amine/mol creatinine). We didn't find a correlation between urinary concentrations of TDI, concentrations in the air and concentrations of toluenediamine (TDA) in the post shift urine samples. Lack of such a correlation may be an effect of the respiratory protective equipment use. Determination of specific IgE in serum is not sensitive enough to serve as a biomarker. Estimation of concentrations of diisocyanate metabolites in urine samples and the presence of work-related allergic symptoms seem to be an adequate method for occupational exposure monitoring of DIC, which may help to determine workers at risk as well as to recognize hazardous workplaces. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Biophysical determinants of toluene diisocyanate antigenicity associated with exposure and asthma.

PubMed

Ye, Young-Min; Kim, Cheol-Woo; Kim, Hyung-Ryul; Kim, Hyun-Mi; Suh, Chang-Hee; Nahm, Dong-Ho; Park, Hae-Sim; Redlich, Carrie A; Wisnewski, Adam V

2006-10-01

Toluene diisocyanate (TDI), a widely used aromatic diisocyanate with the potential to cause asthma, reacts with albumin in the airway fluid, which acts as a carrier protein for chemical presentation to the immune system. Structural elucidation of TDI-albumin conjugates is crucial to understanding the human immune response to TDI exposure. Investigate the dependence of TDI's antigenicity on the biophysics of exposure and its association with TDI asthma. Toluene diisocyanate-albumin conjugates were generated by exposing albumin to TDI in liquid or vapor phase (liquid or vapor TDI-albumin, respectively). Conjugates were characterized by native gel electrophoresis and matrix-assisted laser desorption/ionization-mass spectrometry, and used as antigens in ELISA assays for serum specific-IgE and IgG. The physical phase of TDI (vapor vs liquid) affects the formation of TDI-albumin conjugates, with measurable differences in the amount of TDI per albumin molecule, migration in native gels, matrix-assisted laser desorption/ionization-mass spectrometry mass/charge spectra, and antigenicity. Vapor TDI-albumin conjugates were recognized by IgE from 44% of subjects with TDI asthma, whereas liquid TDI-albumin conjugates are recognized by IgE from only 17% of these patients. A significant (P < .05) association between TDI exposure and vapor TDI-albumin specific serum IgG was also observed. Biophysics of TDI exposure substantially affects formation of TDI-albumin conjugates recognized by the immune system in association with exposure and asthma. The data suggest that serology may help identify TDI asthmatics and exposed workers if the appropriate form of TDI is used as the antigenic basis for analysis.

[Determination and analysis of toluene diisocyanate metabolites in mice using gas chromatography-mass spectrometry].

PubMed

Ji, Yu-Bin; Ji, Chen-Feng; Zou, Xiang; Liu, Hui-Xin

2007-09-01

In the present research we used gas chromatography-mass spectrometry (G C-MS) to determine metabolites of toluene diisocyanate (TDI) in mice and deduce the pathway for toluene diisocyanate metabolism in the organism. Conditions for TDI chromatography: Supelco PTETM-5 chromatographic column (30 mm x 0.25 mm x 0.25 microm); initial column temperature: 90 degrees C, which was maintained for 30 min, then the temperature was increased at a rate of 40 degrees C x min(-1) to 280 degrees C, and maintained for 5.25 min; temperature for the vaporizing chamber: 250 degrees C; carrier gas: helium flowing at 1.0 microL x min(-1). Conditions for chromatography of TDI metabolites in the organism: 94% methyl, 4% ethenyl-bonded-phase fused-silica capillary column (30 + 2 m x 0.25 + 0.02 mm); initial column temperature: 30 degrees C, which was maintained for 5 min, after and then was increased at a rate of 80 degrees C x min(-1) to 280 degrees C, and maintained for 5 min; temperature for the vaporizing chamber: 250 degrees C; carrier gas: helium flowing at 1.0 microL x min(-1). Conditions for mass spectrometry: EI for ionization; 70 eV for ionization energy; 280 degrees C for connecting tube temperature; 35-350 micro for range of scanning; and 1.0 microL for sample size. The results showed that 2 ,4-toluene diisocyanate was metabolized into 2,4-diaminotoluene. Under the conditions selected for GC-MS, TDI metabolites in the organism can be isolated and identified.

40 CFR Table 1 to Subpart Dd of... - List of Hazardous Air Pollutants (HAP) for Subpart DD

Code of Federal Regulations, 2012 CFR

2012-07-01

... 77-78-1 Dimethyl sulfate 0.086 121-69-7 N,N-Dimethylaniline 0.0008 51-28-5 2,4-Dinitrophenol 0.0077... 0.499 110-54-3 Hexane 1.000 78-59-1 Isophorone 0.506 58-89-9 Lindane (all isomers) 1.000 67-56-1...

40 CFR Table 1 to Subpart Dd of... - List of Hazardous Air Pollutants (HAP) for Subpart DD

Code of Federal Regulations, 2013 CFR

2013-07-01

... 77-78-1 Dimethyl sulfate 0.086 121-69-7 N,N-Dimethylaniline 0.0008 51-28-5 2,4-Dinitrophenol 0.0077... 0.499 110-54-3 Hexane 1.000 78-59-1 Isophorone 0.506 58-89-9 Lindane (all isomers) 1.000 67-56-1...

40 CFR 63.8105 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... permit for any affected source required to obtain such a permit; or (3) Fails to meet any emission limit... (incorporated by reference as specified in § 63.14 of subpart A of this part 63); or (2) As obtained from... monomethyl ether acetate 110496 11. Isophorone 78591 12. Methanol 67561 13. Nitrobenzene 98953 14. Toluidine...

Isocyanate asthma: respiratory symptoms caused by diphenyl-methane di-isocyanate

PubMed Central

Tanser, A. R.; Bourke, M. P.; Blandford, A. G.

1973-01-01

Tanser, A. R., Bourke, M. P., and Blandford, A. G. (1973).Thorax, 28, 596-600. Isocyanate asthma: respiratory symptoms caused by diphenyl-methane di-isocyanate. We investigated 57 employees of a factory where diphenyl-methane di-isocyanate (MDI) was used to prepare the materials for making rigid polyurethane foam. Four employees had developed hypersensitivity to MDI. Two had severe, and one moderate asthma, while the fourth had symptoms resembling the delayed hypersensitivity type of reaction. Ten other employees had experienced unpleasant, mainly respiratory, irritant effects from MDI vapour. A past history of bronchitis or of allergy was found more commonly in those with symptoms from MDI than in those without symptoms. It is not known if MDI causes permanent damage to the respiratory tract. The most severely affected cases in the present series had normal spirometric values after recovery, and no persisting symptoms. MDI is safer than other isocyanates used in industry but may cause both major and minor illness. It should be handled with the same precautions as those used with the more toxic compounds. PMID:4784381

Di-Isocyanate Crosslinked Aerogels with 1, 6-Bis (Trimethoxysilyl) Hexane Incorporated in Silica Backbone

NASA Technical Reports Server (NTRS)

Vivod, Stephanie L.; Meador, Mary Ann B.; Nguyen, Baochau N.; Quade, Derek; Randall, Jason; Perry, Renee

2008-01-01

Silica aerogels are desirable materials for many applications that take advantage of their light weight and low thermal conductivity. Addition of a conformal polymer coating which bonds with the amine decorated surface of the silica network improves the strength of the aerogels by as much as 200 times. Even with vast improvement in strength they still tend to undergo brittle failure due to the rigid silica backbone. We hope to increase the flexibility and elastic recovery of the silica based aerogel by altering the silica back-bone by incorporation of more flexible hexane links. To this end, we investigated the use of 1,6-bis(trimethoxysilyl)hexane (BTMSH), a polysilsesquioxane precursor3, as an additional co-reactant to prepare silica gels which were subsequently cross-linked with di-isocyanate. Previously, this approach of adding flexibility by BTMSH incorporation was demonstrated with styrene cross-linked aerogels. In our study, we varied silane concentration, mol % of silicon from BTMSH and di-isocyanate concentration by weight percent to attempt to optimize both the flexibility and the strength of the aerogels.

[Determination of residual toluene diisocyanate in sponge bra by gas chromatography].

PubMed

Wang, Aixia; Ye, Ping; Huang, Nan; Chen, Yan; Li, Xinggen

2017-06-08

A gas chromatography (GC) with internal standard method was developed for the determination of residual toluene diisocyanate (TDI) in sponge bra. The samples were extracted with ethyl acetate dehydrated, and cleaned up with 0.22 μm microfiltration membrane. The residual toluene diisocyanate was separated on a DB-624 capillary column using temperature programming. The flame ionization detector (FID) was used at 250 ℃. The inlet temperature was 180 ℃ with nitrogen as carrier gas. The linear range was 10-200 mg/L ( R 2 =0.9989) for TDI. The average recovery ranged from 80.5% to 91.6% with RSD not more than 7.9%( n =6). The limit of detection (LOD) and limit of quantification (LOQ) were 10 mg/kg and 100 mg/kg, respectively. The developed method was then utilized to analyse the 100 batches of sponge bra samples from the manufacturing enterprises, the entity shops and electric business platforms. The method is simple, time-saving and environment friendly with high sensitivity and good reproducibility, and has practical application value due to its low-cost and short-circle.

Thermal degradation behavior and X-ray diffraction studies of chitosan based polyurethane bio-nanocomposites using different diisocyanates.

PubMed

Javaid, Muhammad Asif; Rizwan, Muhammad; Khera, Rasheed Ahmad; Zia, Khalid Mahmood; Saito, Kei; Zuber, Muhammad; Iqbal, Javed; Langer, Peter

2018-05-29

Five different samples of chitosan based polyurethane bio-nanocomposites (PUBNCs) were synthesized by step growth polymerization technique. Five different diisocyanates were used by keeping hydroxyl terminated polybutadiene (HTPB)/1,4-butane diol (1,4-BDO)/chitosan (CS) and montmorillonite (MMT) clay ratios constant (PUR1-PUR5). For comparative studies, PUR-6 was prepared without CS and clay components. Molecular characterizations of polyurethane (PU) films were carried out by FTIR and NMR which was found to have confirmatory evidence of the proposed structures. X-ray diffraction angles (2θ), d-spacing and intensities of chitosan based samples (PUR1-PUR5) and PUR-6 indicated that crystalline behavior of PUBNCs is influenced by varying diisocyanate structures. TGA/DTA results revealed that chitosan increased thermal stability of PU samples; it also enhanced the mechanical strength and decreased the glass transition temperature (T g ) of all the samples. Based on the above mentioned facts this study suggests the best usage of PUs according to the operational and environmental conditions. Copyright © 2018 Elsevier B.V. All rights reserved.

Energetic Materials - Technology, Manufacturing and Processing, 27th International Annual Conference of ICT June 25 - June 28, 1996 Karisruhe, Federal Republic of Germany.

DTIC Science & Technology

1997-02-01

PROPELLANTS WITH VARYING COMPOSITION L.F. Dimaranan, I. Lee, F.E. Hudson III V12 A COMBUSTION MODEL FOR AN/HTPB-IPDI COMPOSITE SOLID PROPELLANTS P... COMPOSITE PROPELLANTS WITH A LOW PRESSURE EXPONENT SUITABLE FOR NOZZLELESS BOOSTER MOTORS G.J. van Zyl V21 PROPERTIES OF AN AND PSAN/GAP-PROPELLANTS K...APPLICATION B.N. Kondrikov SENSITIVITY TO PROJECTILE IMPACT OF PRE-HEATED EXPLOSIVE COMPOSITIONS H.Cherin, D. Lemoine, L. Gautier VULNERABILITY TESTING OF

The effect of oxidation on the enzyme-catalyzed hydrolytic biodegradation of poly(urethane)s.

PubMed

Labow, Rosalind S; Tang, Yiwen; McCloskey, Christopher B; Santerre, J Paul

2002-01-01

Although the biodegradation of polyurethanes (PU) by oxidative and hydrolytic agents has been studied extensively, few investigations have reported on the combination of their effects. Since neutrophils (PMN) arrive at an implanted device first and release HOCl, followed by monocyte-derived macrophages (MDM) which have potent esterase activities and oxidants of their own, the combined effect of oxidative and hydrolytic degradation on radiolabeled polycarbonate-polyurethanes (PCNU)s was investigated and compared to that of a polyester-PU (PESU) and a polyether-PU (PEU). The PCNUs were synthesized with PCN (MW = 1,000), and butanediol (14C-BD) and one of two diisocyanates, hexane-1,6-diisocyanate (14C-HDI) or methylene bis-p-phenyl diisocyanate (MDI). The PESU and PEU were synthesized using toluene-diisocyanate (14C-TDI), with polycaprolactone and polytetramethylene oxide as soft segments respectively, and ethylene diamine as the chain extender. The effect of pre-treatment with 0.1 mM HOC1 for 1 week on the HDI-based PCNUs and both TDI-based PUs resulted in a significant inhibition of radiolabel release (RR) elicited by cholesterol esterase (CE), when compared to buffer alone, whereas the MDI-based PCNU showed a small but significant increase. When PMN were activated on the HDI-based PCNU surface with phorbol myristate acetate (PMA), HOCl was released for 3 h, and was almost completely abolished by sodium azide (AZ). Simultaneously, the PMN-elicited RR, shown previously to be due to the esterolytic cleavage by serine proteases, was inhibited approximately 75% by PMA-activation of the cells, but significantly increased relative to the latter when AZ was added. Both in vitro oxidation by HOCl and the release of HOCI by PMN were associated with the inhibition of RR and suggest perturbations between oxidative and hydrolytic mechanisms of biodegradation.

40 CFR Table 37 to Subpart G of... - Default Biorates for List 1 Compounds

Code of Federal Regulations, 2014 CFR

2014-07-01

... DIMethyl sulfate 0.178 Dinitrophenol 2,4 0.620 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol... 0.496 Hexachlorobenzene 16.179 ISophorone 0.598 Methanol 0.200 Methyl methacrylate 4.300 Nitrobenzene 2.300 Toluidine (-0) 0.859 Trichlorobenzene 1,2,4 4.393 Trichlorophenol 2,4,5 4.477 Triethylamine...

40 CFR Table 37 to Subpart G of... - Default Biorates for List 1 Compounds

Code of Federal Regulations, 2013 CFR

2013-07-01

... DIMethyl sulfate 0.178 Dinitrophenol 2,4 0.620 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol... 0.496 Hexachlorobenzene 16.179 ISophorone 0.598 Methanol 0.200 Methyl methacrylate 4.300 Nitrobenzene 2.300 Toluidine (-0) 0.859 Trichlorobenzene 1,2,4 4.393 Trichlorophenol 2,4,5 4.477 Triethylamine...

40 CFR Table 37 to Subpart G of... - Default Biorates for List 1 Compounds

Code of Federal Regulations, 2012 CFR

2012-07-01

... DIMethyl sulfate 0.178 Dinitrophenol 2,4 0.620 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol... 0.496 Hexachlorobenzene 16.179 ISophorone 0.598 Methanol 0.200 Methyl methacrylate 4.300 Nitrobenzene 2.300 Toluidine (-0) 0.859 Trichlorobenzene 1,2,4 4.393 Trichlorophenol 2,4,5 4.477 Triethylamine...

40 CFR Table 37 to Subpart G of... - Default Biorates for List 1 Compounds

Code of Federal Regulations, 2011 CFR

2011-07-01

... DIMethyl sulfate 0.178 Dinitrophenol 2,4 0.620 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol... 0.496 Hexachlorobenzene 16.179 ISophorone 0.598 Methanol 0.200 Methyl methacrylate 4.300 Nitrobenzene 2.300 Toluidine (-0) 0.859 Trichlorobenzene 1,2,4 4.393 Trichlorophenol 2,4,5 4.477 Triethylamine...

33 CFR 151.47 - Category D NLSs other than oil-like Category D NLSs that may be carried under this part.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-(Hydroxyethyl)ethylenediamine triacetic acid, trisodium salt solution Isophorone Lactic acid Latex (ammonia (1... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Category D NLSs other than oil-like Category D NLSs that may be carried under this part. 151.47 Section 151.47 Navigation and...

33 CFR 151.47 - Category D NLSs other than oil-like Category D NLSs that may be carried under this part.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-(Hydroxyethyl)ethylenediamine triacetic acid, trisodium salt solution Isophorone Lactic acid Latex (ammonia (1... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Category D NLSs other than oil-like Category D NLSs that may be carried under this part. 151.47 Section 151.47 Navigation and...

33 CFR 151.47 - Category D NLSs other than oil-like Category D NLSs that may be carried under this part.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-(Hydroxyethyl)ethylenediamine triacetic acid, trisodium salt solution Isophorone Lactic acid Latex (ammonia (1... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Category D NLSs other than oil-like Category D NLSs that may be carried under this part. 151.47 Section 151.47 Navigation and...

33 CFR 151.47 - Category D NLSs other than oil-like Category D NLSs that may be carried under this part.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-(Hydroxyethyl)ethylenediamine triacetic acid, trisodium salt solution Isophorone Lactic acid Latex (ammonia (1... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Category D NLSs other than oil-like Category D NLSs that may be carried under this part. 151.47 Section 151.47 Navigation and...

Synthesis and Thermal Analysis of Nano-Aluminum/Fluorinated Polyurethane Elastomeric Composites for Structural Energetics.

PubMed

Zhang, Xianyu; Kim, Jin Seuk; Kwon, Younghwan

2017-04-01

Here we describe the synthesis of polyurethane (PU)-based energetic nanocomposites loaded with nano-aluminum (n-Al) particles. The energetic nanocomposite was prepared by polyurethane reaction of poly(glycidyl azide-co-tetramethylene glycol) (PGT) prepolymers and IPDI/N-100 isocyanates with simultaneous catalyst-free azide-alkyne Click reaction in the presence of n-Al. Initial study carried out with various n-Al/fluorinated PGT blends and demonstrated the potential of fluorinated PGT prepolymer for an energetic PU matrix. Thermal analysis of n-Al/fluorinated PGT-based PU energetic nanocomposite was performed using DSC and TGA.

Isocyanate-induced asthma in a car factory.

PubMed

White, W G; Morris, M J; Sugden, E; Zapata, E

1980-04-05

In a car factory employing 203 women machinists making seat covers more women complained of respiratory symptoms after the introduction of a new seat cover fabric, cropped nylon backed with flame-bonded polyurethane foam (CNPF). 68 women working in the trim shop were studied on the first day back at work after a week's holiday and then at the end of a working week; the incidence of wheezing and/or shortness of breath was greater than expected but there was no difference between peak flow rates. A second study of 192 of the 203 women working in the trim shop confirmed this recent increase in incidence of asthmatic symptoms and showed that significantly more machinists who had worked with this new fabric had a reduced peak flow rate than machinists who had not. Asthma developed in one subject when she was working in the factory sewing CNPF, when she was handling this fabric in the challenge cabinet in the laboratory, and on challenge with toluene di-isocyanate in the laboratory. Airways resistance increased in 3 other workers after exposure to CNPF in the laboratory. Low concentrations (between 0.0003 to 0.003 ppm) of toluene di-isocyanate were found in the air around this fabric. 4 of 9 women with symptoms had IgE antibodies to toluene di-isocyanate.

Risk assessment for consumer exposure to toluene diisocyanate (TDI) derived from polyurethane flexible foam.

PubMed

Arnold, Scott M; Collins, Michael A; Graham, Cynthia; Jolly, Athena T; Parod, Ralph J; Poole, Alan; Schupp, Thomas; Shiotsuka, Ronald N; Woolhiser, Michael R

2012-12-01

Polyurethanes (PU) are polymers made from diisocyanates and polyols for a variety of consumer products. It has been suggested that PU foam may contain trace amounts of residual toluene diisocyanate (TDI) monomers and present a health risk. To address this concern, the exposure scenario and health risks posed by sleeping on a PU foam mattress were evaluated. Toxicity benchmarks for key non-cancer endpoints (i.e., irritation, sensitization, respiratory tract effects) were determined by dividing points of departure by uncertainty factors. The cancer benchmark was derived using the USEPA Benchmark Dose Software. Results of previous migration and emission data of TDI from PU foam were combined with conservative exposure factors to calculate upper-bound dermal and inhalation exposures to TDI as well as a lifetime average daily dose to TDI from dermal exposure. For each non-cancer endpoint, the toxicity benchmark was divided by the calculated exposure to determine the margin of safety (MOS), which ranged from 200 (respiratory tract) to 3×10(6) (irritation). Although available data indicate TDI is not carcinogenic, a theoretical excess cancer risk (1×10(-7)) was calculated. We conclude from this assessment that sleeping on a PU foam mattress does not pose TDI-related health risks to consumers. Copyright © 2012 Elsevier Inc. All rights reserved.

Highly fluorinated polyurethanes

NASA Technical Reports Server (NTRS)

Stump, E. C., Jr.; Rochow, S. E. (Inventor)

1973-01-01

The reaction perfluorinated hydroxyl terminated polyether with diisocyanate to form polyurethane is discussed. Data are given on the resin's oxidation stability, chemical resistance, and low temperature flexibility.

Genome-Wide Association Study Identifies Novel Loci Associated With Diisocyanate-Induced Occupational Asthma

PubMed Central

Yucesoy, Berran; Kaufman, Kenneth M.; Lummus, Zana L.; Weirauch, Matthew T.; Zhang, Ge; Cartier, André; Boulet, Louis-Philippe; Sastre, Joaquin; Quirce, Santiago; Tarlo, Susan M.; Cruz, Maria-Jesus; Munoz, Xavier; Harley, John B.; Bernstein, David I.

2015-01-01

Diisocyanates, reactive chemicals used to produce polyurethane products, are the most common causes of occupational asthma. The aim of this study is to identify susceptibility gene variants that could contribute to the pathogenesis of diisocyanate asthma (DA) using a Genome-Wide Association Study (GWAS) approach. Genome-wide single nucleotide polymorphism (SNP) genotyping was performed in 74 diisocyanate-exposed workers with DA and 824 healthy controls using Omni-2.5 and Omni-5 SNP microarrays. We identified 11 SNPs that exceeded genome-wide significance; the strongest association was for the rs12913832 SNP located on chromosome 15, which has been mapped to the HERC2 gene (p = 6.94 × 10−14). Strong associations were also found for SNPs near the ODZ3 and CDH17 genes on chromosomes 4 and 8 (rs908084, p = 8.59 × 10−9 and rs2514805, p = 1.22 × 10−8, respectively). We also prioritized 38 SNPs with suggestive genome-wide significance (p < 1 × 10−6). Among them, 17 SNPs map to the PITPNC1, ACMSD, ZBTB16, ODZ3, and CDH17 gene loci. Functional genomics data indicate that 2 of the suggestive SNPs (rs2446823 and rs2446824) are located within putative binding sites for the CCAAT/Enhancer Binding Protein (CEBP) and Hepatocyte Nuclear Factor 4, Alpha transcription factors (TFs), respectively. This study identified SNPs mapping to the HERC2, CDH17, and ODZ3 genes as potential susceptibility loci for DA. Pathway analysis indicated that these genes are associated with antigen processing and presentation, and other immune pathways. Overlap of 2 suggestive SNPs with likely TF binding sites suggests possible roles in disruption of gene regulation. These results provide new insights into the genetic architecture of DA and serve as a basis for future functional and mechanistic studies. PMID:25918132

A novel kind of concrete superplasticizer based on aryl isocyanate polycondensates

NASA Astrophysics Data System (ADS)

Ding, Bei; Qian, Shanshan; Qiu, Ying; Wang, Yi; Zheng, Chunyang; Wang, Gaoming

2017-03-01

A novel superplasticizer was synthesized by polycondensation of Alkyl phenol phosphate and toluene diisocyanate grafting with methoxy polyoxyethylene ether (MPEG). The chemical structure and molecular weight of polycondensates molecules were determined by 1H nuclear magnetic resonance (NMR) and gel permeation chromatography respectively. The experimental results indicated that the polycondensates of Alkyl phenol phosphate and toluene diisocyanate grafting with MPEG not only exhibited good water-reducing properties but also demonstrated effective anti-clay abilities alone. Furthermore, the polycondensates showed good fluidity maintaining abilities within 1-3 h and good workability of concrete. The results of T500 Time experiments show that lower plastic viscosity of the polycondensates leads to fresh concrete much “looser” than conventional PCEs in self-compacting concrete.

Dimethylacetamide, ethylenediamine, and diphenylmethane diisocyanate poisoning manifest as acute psychosis and pulmonary edema: treatment with hemoperfusion.

PubMed

Su, T C; Lin, P H; Chiu, M J; Chu, T S; Chang, M J; Wang, J D; Cheng, T J

2000-01-01

A 27-year-old man, employed by a synthetic fiber company, had been exposed to dimethylacetamide, ethylenediamine, and diphenylmethane diisocyanate in a confined space continuously for 4-6 hours per day for 3 days before admission. Hallucinations and delusions were noted at admission; pulmonary edema developed subsequently. The electroencephalogram showed diffuse moderate cortical dysfunction and slow waves at 4-7 Hz, 20-80 microV. Seizures, liver injury, and rhabdomyolysis were noted on the 4th hospital day. The patient was treated by hemoperfusion with a decrease in urine dimethylacetamide from 3,265 mg/g to 4 mg/g creatinine over 4 days. Serial urinary dimethylacetamide and electroencephalogram correlated with the clinical condition.

European Scientific Notes. Volume 37, Number 7.

DTIC Science & Technology

1983-07-31

glycol with isophorone heat given off by immobilized urease as isocyanate bridges. The same crosslink it encounters the substrate. Antigen system can...34Development of a A model with seven degrees of Solute Transport Model for a Multi- layer freedom has been developed for the Ground Water Basin." Many...insufficient device (Figure 1). The amplifier has activation efficiencies, while 900WC two gate "fingers" of 150 jm each and is anneals produce layer

Fact Sheet: Toluene Diisocyanate (TDI) and Related Compounds

EPA Pesticide Factsheets

EPA's existing chemicals programs address pollution prevention, risk assessment, hazard and exposure assessment and/or characterization, and risk management for chemicals substances in commercial use.

40 CFR Table 34 to Subpart G of... - Fraction Measured (Fm) and Fraction Emitted (Fe) For HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2014 CFR

2014-07-01

...-) 542756 1.00 0.76 Diethyl sulfate 64675 0.0025 0.11 Dimethyl sulfate 77781 0.086 0.079 Dimethylaniline (N,N-) 121697 0.00080 0.34 Dimethylhydrazine (1,1-) 57147 0.38 0.054 Dinitrophenol (2,4-) 51285 0.0077... Hexachlorobutadiene 87683 0.88 0.86 Hexachloroethane 67721 0.50 0.85 Hexane 110543 1.00 1.00 Isophorone 78591 0.51 0...

40 CFR Table 34 to Subpart G of... - Fraction Measured (Fm) and Fraction Emitted (Fe) For HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2011 CFR

2011-07-01

...-) 542756 1.00 0.76 Diethyl sulfate 64675 0.0025 0.11 Dimethyl sulfate 77781 0.086 0.079 Dimethylaniline (N,N-) 121697 0.00080 0.34 Dimethylhydrazine (1,1-) 57147 0.38 0.054 Dinitrophenol (2,4-) 51285 0.0077... Hexachlorobutadiene 87683 0.88 0.86 Hexachloroethane 67721 0.50 0.85 Hexane 110543 1.00 1.00 Isophorone 78591 0.51 0...

40 CFR Table 34 to Subpart G of... - Fraction Measured (Fm) and Fraction Emitted (Fe) For HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2012 CFR

2012-07-01

...-) 542756 1.00 0.76 Diethyl sulfate 64675 0.0025 0.11 Dimethyl sulfate 77781 0.086 0.079 Dimethylaniline (N,N-) 121697 0.00080 0.34 Dimethylhydrazine (1,1-) 57147 0.38 0.054 Dinitrophenol (2,4-) 51285 0.0077... Hexachlorobutadiene 87683 0.88 0.86 Hexachloroethane 67721 0.50 0.85 Hexane 110543 1.00 1.00 Isophorone 78591 0.51 0...

40 CFR Table 34 to Subpart G of... - Fraction Measured (Fm) and Fraction Emitted (Fe) For HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2013 CFR

2013-07-01

...-) 542756 1.00 0.76 Diethyl sulfate 64675 0.0025 0.11 Dimethyl sulfate 77781 0.086 0.079 Dimethylaniline (N,N-) 121697 0.00080 0.34 Dimethylhydrazine (1,1-) 57147 0.38 0.054 Dinitrophenol (2,4-) 51285 0.0077... Hexachlorobutadiene 87683 0.88 0.86 Hexachloroethane 67721 0.50 0.85 Hexane 110543 1.00 1.00 Isophorone 78591 0.51 0...

40 CFR Table 34 to Subpart G of... - Fraction Measured (Fm) and Fraction Emitted (Fe) For HAP Compounds in Wastewater Streams

Code of Federal Regulations, 2010 CFR

2010-07-01

...-) 542756 1.00 0.76 Diethyl sulfate 64675 0.0025 0.11 Dimethyl sulfate 77781 0.086 0.079 Dimethylaniline (N,N-) 121697 0.00080 0.34 Dimethylhydrazine (1,1-) 57147 0.38 0.054 Dinitrophenol (2,4-) 51285 0.0077... Hexachlorobutadiene 87683 0.88 0.86 Hexachloroethane 67721 0.50 0.85 Hexane 110543 1.00 1.00 Isophorone 78591 0.51 0...

Disruption of host-seeking behaviour by the salmon louse, Lepeophtheirus salmonis, using botanically derived repellents.

PubMed

O'Shea, B; Wadsworth, S; Pino Marambio, J; Birkett, M A; Pickett, J A; Mordue Luntz, A J

2017-04-01

The potential for developing botanically derived natural products as novel feed-through repellents for disrupting settlement of the salmon louse, Lepeophtheirus salmonis (Caligidae) upon farmed Atlantic salmon, Salmo salar, was investigated using an established laboratory vertical Y-tube behavioural bioassay for assessing copepodid behaviour. Responses to artificial sea water conditioned with the odour of salmon, or to the known salmon-derived kairomone component, α-isophorone, in admixture with selected botanical materials previously known to interfere with invertebrate arthropod host location were recorded. Materials included oils extracted from garlic, Allium sativum (Amaryllidaceae), rosemary, Rosmarinus officinalis (Lamiaceae), lavender, Lavandula angustifolia (Lamiaceae), and bog myrtle, Myrica gale (Myricaceae), and individual components (diallyl sulphide and diallyl disulphide from garlic; allyl, propyl, butyl, 4-pentenyl and 2-phenylethyl isothiocyanate from plants in the Brassica genus). Removal of attraction to salmon-conditioned water (SCW) or α-isophorone was observed when listed materials were presented at extremely low parts per trillion (ppt), that is picograms per litre or 10 -12 level. Significant masking of attraction to SCW was observed at a level of 10 ppt for diallyl disulphide and diallyl sulphide, and allyl isothiocyanate and butyl isothiocyanate. The potential of very low concentrations of masking compounds to disrupt Le. salmonis copepodid settlement on a host fish has been demonstrated in vitro. © 2016 John Wiley & Sons Ltd.

Synthesis and molecular characterization of chitosan based polyurethane elastomers using aromatic diisocyanate.

PubMed

Zia, Khalid Mahmood; Anjum, Sohail; Zuber, Mohammad; Mujahid, Muhammad; Jamil, Tahir

2014-05-01

The present research work was performed to synthesize a new series of chitosan based polyurethane elastomers (PUEs) using poly(ɛ-caprolactone) (PCL). The chitosan based PUEs were prepared by step-growth polymerization technique using poly(ɛ-caprolactone) (PCL) and 2,4-toluene diisocyanate (TDI). In the second step the PU prepolymer was extended with different mole ratios of chitosan and 1,4-butane diol (BDO). Molecular engineering was carried out during the synthesis. The conventional spectroscopic characterization of the synthesized samples using FT-IR confirms the existence of the proposed chitosan based PUEs structure. Internal morphology of the prepared PUEs was studied using SEM analysis. The SEM images confirmed the incorporation of chitosan molecules into the PU backbone. Copyright © 2014 Elsevier B.V. All rights reserved.

Toluene diisocyanate: Induction of the autotaxin-lysophosphatidic acid axis and its association with airways symptoms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broström, Julia M.; Ye, Zhi-wei; Axmon, Anna

Diisocyanates are industrial chemicals which have a wide range of applications in developed and developing countries. They are notorious lung toxicants and respiratory sensitizers. However, the mechanisms behind their adverse effects are not adequately characterized. Autotaxin (ATX) is an enzyme producing lysophosphatidic acid (LPA), and the ATX-LPA axis has been implicated in lung related inflammatory conditions and diseases, including allergic asthma, but not to toxicity of environmental low-molecular-weight chemicals. We investigated effects of toluene diisocyanate (TDI) on ATX induction in human lung epithelial cell models, and we correlated LPA-levels in plasma to biomarkers of TDI exposure in urine collected frommore » workers exposed to < 5 ppb (parts per billion). Information on workers' symptoms was collected through interviews. One nanomolar TDI robustly induced ATX release within 10 min in vitro. A P2X7- and P2X4-dependent microvesicle formation was implicated in a rapid ATX release and a subsequent protein synthesis. Co-localization between purinergic receptors and ATX was documented by immunofluorescence and confocal microscopy. The release was modulated by monocyte chemoattractant protein-1 (MCP-1) and by extracellular ATP. In workers, we found a dose–response relationship between TDI exposure biomarkers in urine and LPA levels in plasma. Among symptomatic workers reporting “sneezing”, the LPA levels were higher than among non-symptomatic workers. This is the first report indicating induction of the ATX-LPA axis by an environmental low-molecular-weight chemical, and our data suggest a role for the ATX-LPA axis in TDI toxicity. - Highlights: • Human epithelial cells release autotaxin in response to 1 nM toluene diisocyanate (TDI). • The release involves P2X4 and P2X7 receptors and is modulated by ATP and MCP-1. • Lysophosphatidic acid (LPA) was measured in workers exposed to < 5 ppb TDI. • LPA in plasma correlated to TDI exposure biomarkers in workers. • Symptomatic workers had higher LPA levels than those without symptoms.« less

Presidential Green Chemistry Challenge: 2005 Greener Reaction Conditions Award

EPA Pesticide Factsheets

Presidential Green Chemistry Challenge 2005 award winner, BASF, invented a one-component, urethane acrylate oligomer primer system for automobile refinishing that is UV-curable, has VOCs, and is free of diisocyanates.

Antibodies against toluene diisocyanate protein conjugates. Three methods of measurement.

PubMed

Patterson, R; Harris, K E; Zeiss, C R

1983-12-01

With the use of canine antisera against toluene diisocyanate (TDI)-dog serum albumin (DSA), techniques for measuring antibody against TDI-DSA were evaluated. The use of an ammonium sulfate precipitation assay showed suggestive evidence of antibody binding but high levels of TDI-DSA precipitation in the absence of antibody limit any usefulness of this technique. Double-antibody co-precipitation techniques will measure total antibody or Ig class antibody against 125I-TDI-DSA. These techniques are quantitative. The polystyrene tube radioimmunoassay is a highly sensitive method of detecting and quantitatively estimating IgG antibody. The enzyme linked immunosorbent assay is a rapidly adaptable method for the quantitative estimation of IgG, IgA, and IgM against TDI-homologous proteins. All these techniques were compared and results are demonstrated by using the same serum sample for analysis.

Microwave-assisted synthesis of cyclodextrin polyurethanes.

PubMed

Biswas, Atanu; Appell, Michael; Liu, Zengshe; Cheng, H N

2015-11-20

Cyclodextrin (CD) has often been incorporated into polyurethanes in order to facilitate its use in encapsulation or removal of organic species for various applications. In this work a microwave-assisted method has been developed to produce polyurethanes consisting of α-, β-, and γ-CD and three common diisocyanates. As compared to conventional heating, this new synthetic method saves energy, significantly reduces reaction time, and gets similar or improved yield. The reaction products have been fully characterized with (13)C, (1)H, and two-dimensional NMR spectroscopy. With suitable stoichiometry of starting CD and diisocyanate, the resulting CD polyurethane is organic-soluble and water-insoluble and is shown to remove Nile red dye and phenol from water. Possible applications include the removal of undesirable materials from process streams, toxic compounds from the environment, and encapsulation of color or fragrance molecules. Published by Elsevier Ltd.

Hemoglobin adducts in workers exposed to 1,6-hexamethylene diisocyanate

PubMed Central

Flack, Sheila L.; Fent, Kenneth W.; Gaines, Linda G. T.; Thomasen, Jennifer M.; Whittaker, Stephen G.; Ball, Louise M.; Nylander-French, Leena A.

2014-01-01

We investigated the utility of 1,6-hexamethylene diamine (HDA) hemoglobin adducts as biomarkers of exposure to 1,6-hexamethylene diisocyanate (HDI) monomer. Blood samples from 15 spray painters applying HDI-containing paint were analyzed for hemoglobin HDA (HDA-Hb) and N-acetyl-1,6-hexamethylene diamine (monoacetyl-HDA-Hb) by GC-MS. HDA-Hb was detected in the majority of workers (≤1.2–37 ng/g Hb), whereas monoacetyl-HDA-Hb was detected in one worker (0.06 ng/g Hb). The stronger, positive association between HDA-Hb and cumulative HDI exposure (r2 = 0.3, p < 0.06) than same day exposure (p ≥ 0.13) indicates long-term elimination kinetics for HDA-Hb adducts. This association demonstrates the suitability of HDA-Hb adducts for further validation as a biomarker of HDI exposure. PMID:21506697

Use of hexyl isocyanate antigen to detect antibodies to hexamethylene diisocyanate (HDI) in sensitized guinea pigs and in a sensitized worker.

PubMed

Karol, M H; Hauth, B A

1982-01-01

Hypersensitivity to hexamethylene diisocyanate (HDI) has been reported following occupational exposure. Diagnosis of sensitivity is usually made from clinical evaluation of symptomatology. An in vitro serologic assay for HDI sensitivity was developed by immunizing guinea pigs with HDI and with hexyl isocyanate (HMI). Animals injected intradermally with HMI produced hapten-specific antibodies whereas guinea pigs injected with HDI produced antibodies specific for larger determinants which included the HDI hapten. The larger determinants were assumed to be composed of portions of "self" molecules which reacted in vivo with HDI. Serum albumin appeared to be one such molecule. No cross reactions were noted between antibodies to HDI and another widely used industrial isocyanate, toluene diisocyanate (TDI). Antigens effective in detecting antibodies to HDI or HMI were tested for ability to detect reaginic antibodies in a worker with clinical "HDI" asthma. Using a radioimmunoassay (RAST), antibodies reacted with conjugates containing either HDI or HMI as haptens. In addition, the prevalance of HDI polyisocyanates (Desmodur N) in spray paints prompted its use as a hapten. Antibodies reacted with Desmodur N antigen conjugates in RAST. RAST inhibition further indicated that Desmodur N antigen reacted more readily with the patient's antibodies than did HDI or HMI antigens. These results suggest that the patient may have been exposed to HDI polyisocyanates in spray paint application. Use of Rast inhibition for diagnosis of sensitivity may indicate the precise sensitizing agent within a mixture.

Composite elastomeric polyurethane scaffolds incorporating small intestinal submucosa for soft tissue engineering.

PubMed

Da, Lincui; Gong, Mei; Chen, Anjing; Zhang, Yi; Huang, Yizhou; Guo, Zhijun; Li, Shengfu; Li-Ling, Jesse; Zhang, Li; Xie, Huiqi

2017-09-01

Although soft tissue replacement has been clinically successful in many cases, the corresponding procedure has many limitations including the lack of resilience and mechanical integrity, significant donor-site morbidity, volume loss with time, and fibrous capsular contracture. These disadvantages can be alleviated by utilizing bio-absorbable scaffolds with high resilience and large strain, which are capable of stimulating natural tissue regeneration. Hence, the chemically crosslinked tridimensional scaffolds obtained by incorporating water-based polyurethane (PU) (which was synthesized from polytetramethylene ether glycol, isophorone diisocyanate, and 2,2-bis(hydroxymethyl) butyric acid) into a bioactive extracellular matrix consisting of small intestinal submucosa (SIS) have been tested in this study to develop a new approach for soft tissue engineering. After characterizing the structure and properties of the produced PU/SIS composites, the strength, Young's modulus, and resilience of wet PU/SIS samples were compared with those of crosslinked PU. In addition, the fabricated specimens were investigated using human umbilical vein endothelial cells to evaluate their ability to enhance cell attachment and proliferation. As a result, the synthesized PU/SIS samples exhibited high resilience and were capable of enhancing cell viability with no evidence of cytotoxicity. Subcutaneous implantation in animals and the subsequent testing conducted after 2, 4, and 8weeks indicated that sound implant integration and vascularization occurred inside the PU/SIS composites, while the presence of SIS promoted cell infiltration, angiogenesis, and ultimately tissue regeneration. The obtained results revealed that the produced PU/SIS composites were characterized by high bioactivity and resilience, and, therefore, could be used for soft tissue engineering applications. Hybrid composites containing synthetic polymers with high mechanical strength and naturally derived components, which create a bio-mimetic environment, are one of the most promising biomaterials. Although synthetic polymer/ECM composites have been previously used for soft tissue repair, their resilience properties were not investigated in sufficient detail, while the development of elastic composites composed of synthetic polymers and ECMs in nontoxic aqueous solutions remains a rather challenging task. In this study, porous PU/SIS composites were fabricated in a non-toxic manner; the obtained materials exhibited sufficient mechanical support, which promote cell growth, angiogenesis, and tissue regeneration. The described method can be adapted for the development of scaffolds with various acellular matrices and subsequently used during the restoration of particular types of tissue. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Dynamic characterization of frequency response of shock mitigation of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam

DOE PAGES

Song, Bo; Nelson, Kevin

2015-09-01

Kolsky compression bar experiments were conducted to characterize the shock mitigation response of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam, abbreviated as PMDI foam in this study. The Kolsky bar experimental data was analyzed in the frequency domain with respect to impact energy dissipation and acceleration attenuation to perform a shock mitigation assessment on the foam material. The PMDI foam material exhibits excellent performance in both energy dissipation and acceleration attenuation, particularly for the impact frequency content over 1.5 kHz. This frequency (1.5 kHz) was observed to be independent of specimen thickness and impact speed, which may represent themore » characteristic shock mitigation frequency of the PMDI foam material under investigation. The shock mitigation characteristics of the PMDI foam material were insignificantly influenced by the specimen thickness. As a result, impact speed did have some effect.« less

Longitudinal and Cross-sectional Analyses of Lung Function in Toluene Diisocyanate Production Workers.

PubMed

Wang, Mei Lin; Storey, Eileen; Cassidy, Laura D; Doney, Brent; Conner, Patrick R; Collins, James J; Carson, Michael; Molenaar, Don

2017-12-01

The aim of this study was to investigate lung function among toluene diisocyanate (TDI) production workers. One hundred ninety-seven U.S workers performed spirometry from 2006 through 2012. Results were compared within the study cohort and with U.S. population measures. A mixed-effects model assessed factors affecting repeated forced expiratory volume in 1 second (FEV1) measurements. The cohort's mean FEV1 and forced vital capacity (FVC) percent reference values, although greater than 90%, were significantly lower and the prevalence of abnormal spirometry (predominantly restrictive pattern) was significantly higher than in the U.S. Differences in lung function among workers with higher cumulative TDI exposure were in the direction of an exposure effect, but not significant. We found little evidence of an adverse effect of TDI exposure on longitudinal spirometry in these workers. The association between TDI exposure and the increasing prevalence of a restrictive pattern needs further exploration.

Dynamic characterization of frequency response of shock mitigation of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Nelson, Kevin

Kolsky compression bar experiments were conducted to characterize the shock mitigation response of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam, abbreviated as PMDI foam in this study. The Kolsky bar experimental data was analyzed in the frequency domain with respect to impact energy dissipation and acceleration attenuation to perform a shock mitigation assessment on the foam material. The PMDI foam material exhibits excellent performance in both energy dissipation and acceleration attenuation, particularly for the impact frequency content over 1.5 kHz. This frequency (1.5 kHz) was observed to be independent of specimen thickness and impact speed, which may represent themore » characteristic shock mitigation frequency of the PMDI foam material under investigation. The shock mitigation characteristics of the PMDI foam material were insignificantly influenced by the specimen thickness. As a result, impact speed did have some effect.« less

Effect of 1,6-hexamethylene diisocyanate exposure on peak flowmetry in automobile paint shop workers in Iran.

PubMed

Pourabedian, Siyamak; Barkhordari, Abdullah; Habibi, Ehsanallah; Rismanchiyan, Masoud; Zare, Mohsen

2010-06-01

The aim of this study was to investigate the effects of occupational exposure to 1,6-hexamethylene diisocyanate (HDI) on peak flowmetry in automobile body paint shop workers in Iran. We studied a population of 43 car painters exposed to HDI at their workplaces. Peak expiratory flow was tested for one working week, from the start to the end of each shift. Air was sampled and HDI analysed in parallel, according to the OSHA 42 method. Daily and weekly HDI exposure averages were (0.42+/-0.1) mg m(-3) and (0.13+/-0.05) mg m(-3), respectively. On painting days, 72 % of workers showed more than a 10 % variation in peak expiratory flow. Inhalation exposure exceeded the threshold limit value (TLV) ten times over. This strongly suggests that HDI affected the peak flowmetry in the studied workers.

Hemoglobin adducts in workers exposed to 1,6-hexamethylene diisocyanate.

PubMed

Flack, Sheila L; Fent, Kenneth W; Gaines, Linda G T; Thomasen, Jennifer M; Whittaker, Stephen G; Ball, Louise M; Nylander-French, Leena A

2011-05-01

We investigated the utility of 1,6-hexamethylene diamine (HDA) hemoglobin adducts as biomarkers of exposure to 1,6-hexamethylene diisocyanate (HDI) monomer. Blood samples from 15 spray painters applying HDI-containing paint were analyzed for hemoglobin HDA (HDA-Hb) and N-acetyl-1,6-hexamethylene diamine (monoacetyl-HDA-Hb) by GC-MS. HDA-Hb was detected in the majority of workers (≤1.2-37 ng/g Hb), whereas monoacetyl-HDA-Hb was detected in one worker (0.06 ng/g Hb). The stronger, positive association between HDA-Hb and cumulative HDI exposure (r(2) = 0.3, p < 0.06) than same day exposure (p ≥ 0.13) indicates long-term elimination kinetics for HDA-Hb adducts. This association demonstrates the suitability of HDA-Hb adducts for further validation as a biomarker of HDI exposure.

Diisocyanate-exposed auto body shop workers: a one-year follow-up.

PubMed

Redlich, C A; Stowe, M H; Coren, B A; Wisnewski, A V; Holm, C T; Cullen, M R

2002-12-01

Diisocyanates currently are the most commonly identified cause of occupational asthma in industrialized countries. Auto body shops, a common hexamethylene diisocyanate (HDI) exposure setting, are difficult to study due to their small size and episodic exposures. A 1-year follow-up was undertaken as an adjunct to the cross-sectional SPRAY study (Survey of Painters & Repairers of Auto bodies by Yale) to investigate the effects of HDI on auto body shop workers over time and whether or not the healthy worker effect may exist in this industry. Forty-eight workers from seven shops were re-contacted. Thirty-four subjects who stayed at the same shop and 11 who left their original shop participated. No statistically significant changes in physiology, symptoms, and immunologic responses from baseline to follow-up were noted. However, significant differences between those who left the shops and those who stayed were noted. Those who left were younger, less experienced in the industry, and more likely to have a history of asthma (23 vs. 3%; P < 0.05), bronchial hyper-responsiveness (23 vs. 9%), HDI-specific IgG (64 vs. 29%; P < 0.05), and HDI-specific proliferation (S.I. 2.0 vs. 1.3; P < 0.05). The differences in workers who stayed at their shop compared to those who left, combined with the low asthma prevalence and high job turnover rate, all suggest that a healthy worker effect may exist in the auto body industry, and may in part account for the low prevalence of asthma noted in SPRAY and other cross-sectional studies of diisocyante workers. Copyright 2002 Wiley-Liss, Inc.

75 FR 37795 - Certain New Chemicals; Receipt and Status Information

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-30

...-methyl-, polymer with alkyl 2- propenoates, ethenyl acetate and methyl-2- methyl-2-propenoate P-10-0389...), polymers with cycloaliphatic diamine, alkyldiisocyanate, alpha-hydro-omega- hydroxy(alkyldiyl) and... dicarboxylic acid, polymer with cycloaliphatic diamine, aliphatic diisocyanate, aliphatic dicarboxylic acid...

Preparation of highly fluorinated polyurethanes

NASA Technical Reports Server (NTRS)

Rochow, S. E.; Stump, E. C., Jr.

1971-01-01

New polyurethanes, formed from a reaction of a prepolymer diol and a perfluorinated diisocyanate, are nonflammable and possess high corrosion resistance and good low temperature flexibility. Polymer hardness increases rapidly with increasing ratio of diisocaynate to diol, but its glass transition temperature is not adversely affected.

Developing testing methods for characterizing emissions and sources of exposures from polyurehane products

EPA Science Inventory

The relationship between onsite manufacture of spray polyurethane foam insulation (SPFI) and potential exposures to diisocyanate compounds, amine catalysts, flame retardants, and blowing agents, as well as aldehydes and other volatile or semivolatile organic compounds that may be...

The Development of Testing Methods for Characterizing Emissions and Sources of Exposures from Polyurethane Products

EPA Science Inventory

The relationship between onsite manufacture of spray polyurethane foam insulation (SPFI) and potential exposures is not well understood. Currently, no comprehensive standard test methods exist for characterizing and quantifying product emissions. Exposures to diisocyanate compoun...

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63... foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage... of pumps, valves, connectors, pressure-relief devices, and open-ended valves or lines in HAP ABA...

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63... foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage... of pumps, valves, connectors, pressure-relief devices, and open-ended valves or lines in HAP ABA...

78 FR 37818 - Request for Information on Toluene Diisocyanates

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-24

.... engineering controls, work practices, personal protective equipment, exposure data before and after... Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) for TDI is 0.005 ppm... vitro and in vivo studies. (7) Information on control measures (e.g., engineering controls, work...

Development of test systems for characterizing emissions from spray polyurethane foam insulation (SPFI)

EPA Science Inventory

The relationship between onsite manufacture of spray polyurethane foam insulation (SPFI) and potential exposures to diisocyanates, amines, flame retardants (FRs), blowing agents, aldehydes and other organic compounds that may be emitted from SPFI is not well understood. EPA is de...

Determination of albumin adducts of 4,4'-methylenediphenyl diisocyanate after specific inhalative challenge tests in workers.

PubMed

Sabbioni, Gabriele; Dongari, Nagaraju; Kumar, Anoop; Baur, Xaver

2016-10-17

4,4'-Methylenediphenyl diisocyanate (MDI) is the most important isocyanate used in the industry. Lung sensitization with bronchial asthma is the main disorder in exposed workers. Albumin adducts of MDI might be involved in specific immunological reactions. MDI adducts with lysine (MDI-Lys) of albumin have been found in MDI-workers and construction workers. MDI-Lys is an isocyanate-specific adduct of MDI with albumin. In the present study, we report MDI-adducts in workers undergoing diagnostic MDI challenge tests. The workers were exposed for 2h to 5ppb of MDI. The adduct levels increase significantly after the exposure to MDI in the challenge chamber. About 0.6% of the dose was bound to albumin. So far, only urinary metabolites of MDI were measured to monitor isocyanate workers. However, such urinary metabolites are not isocyanate specific. Therefore, we propose to measure albumin adducts for monitoring MDI exposed subjects. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Evaluation of workers' exposure to methylene diphenyl diisocyanate (MDI) in an automobile manufacturing company, Iran.

PubMed

Kakooei, Hossein; Shahtaheri, Seyed Jamaleddin; Karbasi, Hossein-Ali

2006-01-01

Evaluation of personal inhalation exposure to methylene diphenyl diisocyanate (MDI) among 39 employees, working in the window fixation and window glue processes in an automobile manufacturing company was performed. This study was conducted for both case and control groups. After sampling and sample preparation processes, MDI was determined with a UV-VIS spectrophotometer at 590 nm; the lung function was assessed with a digital spirometer, too. The average concentration of MDI in the window fixation, and window glue workplaces were 34.53 and 27.37 micro g/m3, respectively, which was lower than the threshold limit value (TLV) recommended by the American Conference of Governmental Industrial Hygienists (ACGIH) (51 micro g/m3). Respiratory symptoms in the exposed group were significantly different compared to the unexposed group (p < .05). Lung capacities in the case group were lower than in the control group (p < .05). Therefore, MDI can be easily measured making it possible to evaluate the adverse effects caused by occupational exposure.

Modeling Heat Transfer and Pressurization of Polymeric Methylene Diisocyanate (PMDI) Polyurethane Foam in a Sealed Container.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, Sarah Nicole

Polymer foam encapsulants provide mechanical, electrical, and thermal isolation in engineered systems. It can be advantageous to surround objects of interest, such as electronics, with foams in a hermetically sealed container to protect the electronics from hostile en vironments, such as a crash that produces a fire. However, i n fire environments, gas pressure from thermal decomposition of foams can cause mechanical failure of the sealed system . In this work, a detailed study of thermally decomposing polymeric methylene diisocyanate (PMDI) - polyether - polyol based polyurethane foam in a sealed container is presented . Both experimental and computational workmore » is discussed. Three models of increasing physics fidelity are presented: No Flow, Porous Media, and Porous Media with VLE. Each model us described in detail, compared to experiment , and uncertainty quantification is performed. While the Porous Media with VLE model matches has the best agreement with experiment, it also requires the most computational resources.« less

Microwave-assisted synthesis of isosorbide-derived diols for the preparation of thermally stable thermoplastic polyurethane

PubMed Central

Kasmi, Nejib; Roso, Martina; Hammami, Nadia; Majdoub, Mustapha; Boaretti, Carlo; Sgarbossa, Paolo; Vianello, Chiara; Maschio, Giuseppe; Modesti, Michele; Lorenzetti, Alessandra

2017-01-01

Abstract In order to prepare thermally stable isosorbide-derived thermoplastic polyurethane, the synthesis of two new chiral exo–exo configured diols, prepared from isosorbide, and two types of diphenols (bisphenol A and thiodiphenol) was described. The synthesis conditions were optimized under conventional heating and microwave irradiations. To prove their suitability in polymerization, these monomers were successfully polymerized using 4,4′-diphenylmethane diisocyanate (MDI) and hexamethylene diisocyanate (HDI). Both monomers and polymers have been studied by NMR, FT-IR, TGA, DSC; intrinsic viscosity of polymers has also been determined. The results showed the effectiveness of the synthetic strategy proposed; moreover, a dramatic reduction of the reaction time and an important improvement of the monomers yield using microwave irradiation have been demonstrated. The monomers, as well as the polymers, showed excellent thermal stability both in air and nitrogen. It was also shown that the introduction of sulphur in the polyurethane backbone was effective in delaying the onset of degradation as well as the degradation rate. PMID:29491826

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63.1306 Reporting... the information listed in paragraph (d)(4) of this section for molded foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage vessels, along with a record of...

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63.1306 Reporting... the information listed in paragraph (d)(4) of this section for molded foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage vessels, along with a record of...

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63.1306 Reporting... the information listed in paragraph (d)(4) of this section for molded foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage vessels, along with a record of...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

INCONSISTENCIES BETWEEN CYTOKINE PROFILES, ANTIBODY RESPONSES, AND RESPIRATORY HYPERRESPONSIVENESS FOLLOWING DERMAL EXPOSURE TO ISOCYANATES

EPA Science Inventory

Cytokine profiling of local lymph node responses has been proposed as a simple test to identify chemicals, such as low molecular weight diisocyanates, that pose a significant risk of occupational asthma. Previously, we reported cytokine mRNA profiles for dinitrochlorobenzene (DNC...

Novel polyurethanes from xylan and TDI: Preparation and characterization

USDA-ARS?s Scientific Manuscript database

In this work a novel polyurethane was developed involving xylan and tolylene-2,4-diisocyanate (TDI). Polymer synthesis was achieved via conventional heat or microwave-assisted reaction in dimethylsulfoxide. Because xylan has multiple OH groups on each polymer chain, the TDI/xylan molar ratio neede...

Liner Technology Program. Volume 3. Liner Development Methodology Manual

DTIC Science & Technology

1982-05-01

derivative of trimesic acid, trimenoyl-l- (2-ethyl) aziridine BNO Hydroxyl ethyl ester of carboxy-terminated polybutadiene Catocene Liquid ferrocene ...diisocyanate MAPO rris-l-(2-methyl) aziridinyl phosphine oxide I.’ lNA Methyl nedic anhydride; methyl endo-cis-cicyolo-2,2,1-5- heptene-2,3-dicarboxylic

40 CFR 63.1300 - Standards for molded flexible polyurethane foam production.

Code of Federal Regulations, 2013 CFR

2013-07-01

... polyurethane foam production. 63.1300 Section 63.1300 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Foam Production § 63.1300 Standards for molded flexible polyurethane foam production. Each owner or... polyurethane foam process, with the following exception. Diisocyanates may be used to flush the mixhead and...

40 CFR 63.1300 - Standards for molded flexible polyurethane foam production.

Code of Federal Regulations, 2014 CFR

2014-07-01

... polyurethane foam production. 63.1300 Section 63.1300 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Foam Production § 63.1300 Standards for molded flexible polyurethane foam production. Each owner or... polyurethane foam process, with the following exception. Diisocyanates may be used to flush the mixhead and...

A COMPARISON OF CYTOKINE MESSAGE AND PROTEIN PROFILES OBTAINED FOLLOWING DERMAL EXPOSURE TO DIISOCYANATES.

EPA Science Inventory

Exposure to certain low molecular weight chemicals is associated with asthma. A simple method to identify this hazard is needed. Increased expression of Th2 cytokine mRNA in draining lymph nodes following dermal exposure and increased production of Th2 cytokines by cultured cell...

78 FR 41853 - Safety Advisory Guidance: Heating Rail Tank Cars To Prepare Hazardous Material for Unloading or...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-12

... rail tank car due to chemical self-reaction and expansion of the toluene diisocyanate matter wastes. On...: Cheryl West Freeman, Division of Engineering and Research, Pipeline and Hazardous Materials Safety... catastrophically ruptured at a transfer station at the BASF Corporation chemical facility in Freeport, Texas. The...

Aspen flakeboard treated with disodium octaborate tetrahydrate

Treesearch

Robert H. White; John Forsman; John R. Erickson

2008-01-01

In this project, we investigated mechanical properties and fire performance of aspen flakeboards manufactured with the fire-retardant chemical disodium octaborate tetrahydrate (DOT). Flakeboards were prepared using two levels of adhesive loading (5% and 7% methylene diphenyl diisocyanate (MDI)) and three levels of fire-retardant treatments (6%, 9%, and 12%). DOT is a...

40 CFR 721.10607 - Aliphatic diisocyanate, homopolymer, alkanol-blocked (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

...-purifying, tight-fitting half-face respirator equipped with N100 (if oil aerosols absent), R100, or P100 filters. (B) NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 (if oil...-certified powered air-purifying respirator equipped with a tight-fitting facepiece (either half-face or full...

Determination of isocyanate specific albumin-adducts in workers exposed to toluene diisocyanates.

PubMed

Sabbioni, Gabriele; Gu, Qi; Vanimireddy, Lakshiminiranjan Reddy

2012-03-01

Toluene diisocyanates (2,4-TDI and 2,6-TDI) are important intermediates in the chemical industry. Among the main damages after low levels of TDI exposure are lung sensitization and asthma. It is therefore necessary to have sensitive and specific methods to monitor isocyanate exposure of workers. Urinary metabolites or protein adducts have been used as biomarkers in workers exposed to TDI. However, with these methods it was not possible to determine if the biomarkers result from exposure to TDI or to the corresponding toluene diamines (TDA). This work presents a new procedure for the determination of isocyanate-specific albumin adducts. Isotope dilution mass spectrometry was used to measure the adducts in albumin present in workers exposed to TDI. 2,4-TDI and 2,6-TDI formed adducts with lysine: N(ϵ)-[({3-amino-4-methylphenyl}amino)carbonyl]-lysine, N(ϵ)-[({5-amino-2-methylphenyl}amino)carbonyl]-lysine, and N(ϵ)- [({3-amino-2-methylphenyl}amino)carbonyl]-lysine. In future studies, this new method can be applied to measure TDI-exposures in workers.

Synthesis and characterization of thiolated carboxymethyl chitosan-graft-cyclodextrin nanoparticles as a drug delivery vehicle for albendazole.

PubMed

Alamdarnejad, Ghazaleh; Sharif, Alireza; Taranejoo, Shahrouz; Janmaleki, Mohsen; Kalaee, Mohammad Reza; Dadgar, Mohsen; Khakpour, Mazyar

2013-08-01

A new strategy for the synthesis of thiolated carboxymethyl chitosan-g-cyclodextrin nanoparticles by an ionic-gelation method is presented. The synthetic approach was based on the utilization of 1,6-hexamethylene diisocyanate during cyclodextrin grafting onto carboxymethyl chitosan. The use of the 1,6-hexamethylene diisocyanate resulted in reactions between cyclodextrin and active sites at the C6-position of chitosan, and preserved amino groups of chitosan for subsequent reactions with thioglycolic acid, as the thiolating agent, and tripolyphosphate, as the gelling counterion. Various methods such as scanning electron microscopy, rheology and in vitro release studies were employed to exhibit significant features of the nanoparticles for mucosal albendazole delivery applications. It was found that the thiolated carboxymethyl chitosan-g-cyclodextrin nanoparticles prepared using an aqueous solution containing 1 wt% of tripolyphosphate and having 115.65 (μmol/g polymer) of grafted thiol groups show both the highest mucoadhesive properties and the highest albendazole entrapment efficiency. The latter was confirmed theoretically by calculating the enthalpy of mixing of albendazole in the above thiolated chitosan polymer.

Properties of Graphene/Shape Memory Thermoplastic Polyurethane Composites Actuating by Various Methods

PubMed Central

Park, Jin Ho; Dao, Trung Dung; Lee, Hyung-il; Jeong, Han Mo; Kim, Byung Kyu

2014-01-01

Shape memory behavior of crystalline shape memory polyurethane (SPU) reinforced with graphene, which utilizes melting temperature as a shape recovery temperature, was examined with various external actuating stimuli such as direct heating, resistive heating, and infrared (IR) heating. Compatibility of graphene with crystalline SPU was adjusted by altering the structure of the hard segment of the SPU, by changing the structure of the graphene, and by changing the preparation method of the graphene/SPU composite. The SPU made of aromatic 4,4′-diphenylmethane diisocyanate (MSPU) exhibited better compatibility with graphene, having an aromatic structure, compared to that made of the aliphatic hexamethylene diisocyanate. The finely dispersed graphene effectively reinforced MSPU, improved shape recovery of MSPU, and served effectively as a filler, triggering shape recovery by resistive or IR heating. Compatibility was enhanced when the graphene was modified with methanol. This improved shape recovery by direct heating, but worsened the conductivity of the composite, and consequently the efficiency of resistive heating for shape recovery also declined. Graphene modified with methanol was more effective than pristine graphene in terms of shape recovery by IR heating. PMID:28788529

Incidence of cancer and exposure to toluene diisocyanate and methylene diphenyldiisocyanate: a cohort based case-referent study in the polyurethane foam manufacturing industry.

PubMed Central

Hagmar, L; Strömberg, U; Welinder, H; Mikoczy, Z

1993-01-01

OBJECTIVE--To assess the association between occupational exposure to toluene diisocyanate or methylene diphenyldiisocyanate and risk of cancer. DESIGN--A cohort based case-referent study. STUDY BASE--7023 subjects employed during the period 1958 to 1987 in nine Swedish polyurethane foam manufacturing plants. MAIN OUTCOME MEASURES--Odds ratios adjusted with respect to the matching factors (age at risk, calendar year at risk, sex, and plant), calculated from the conditional logistic regression model. RESULTS--A non-significant association was found between high exposure to isocyanates and prostate cancer (OR 2.66, 90% confidence interval (90% CI) 0.39-18.1), which was not enhanced when an induction latency period of 10 years was applied. An association between isocyanate exposure and colon cancer was even weaker. No associations were seen for non-Hodgkin's lymphoma and rectal cancer. CONCLUSIONS--The tentative associations, derived from a previous cohort study, between isocyanate exposure and excess risk for non-Hodgkin's lymphoma and rectal cancer were not supported. Instead, non-significant associations with prostate cancer, and possibly colon cancer, were seen. PMID:8280625

Melt electrospinning of biodegradable polyurethane scaffolds

PubMed Central

Karchin, Ari; Simonovsky, Felix I.; Ratner, Buddy D.; Sanders, Joan E.

2014-01-01

Electrospinning from the melt, in contrast to from solution, is an attractive tissue engineering scaffold manufacturing process as it allows for the formation of small diameter fibers while eliminating potentially cytotoxic solvents. Despite this, there is a dearth of literature on scaffold formation via melt electrospinning. This is likely due to the technical challenges related to the need for a well-controlled high temperature setup and the difficulty in developing an appropriate polymer. In this paper, a biodegradable and thermally stable polyurethane (PU) is described specifically for use in melt electrospinning. Polymer formulations of aliphatic PUs based on (CH2)4-content diisocyanates, polycaprolactone (PCL), 1,4-butanediamine and 1,4-butanediol (BD) were evaluated for utility in the melt electrospinning process. The final polymer formulation, a catalyst-purified PU based on 1,4-butane diisocyanate, PCL and BD in a 4/1/3 molar ratio with a weight-average molecular weight of about 40 kDa, yielded a nontoxic polymer that could be readily electrospun from the melt. Scaffolds electrospun from this polymer contained point bonds between fibers and mechanical properties analogous to many in vivo soft tissues. PMID:21640853

Tunable polymeric sorbent materials for fractionation of model naphthenates.

PubMed

Mohamed, Mohamed H; Wilson, Lee D; Headley, John V

2013-04-04

The sorption properties are reported for several examples of single-component carboxylic acids representing naphthenic acids (NAs) with β-cyclodextrin (β-CD) based polyurethane sorbents. Seven single-component examples of NAs were chosen with variable z values, carbon number, and chemical structure as follows: 2-hexyldecanoic acid (z = 0 and C = 16; S1), n-caprylic acid (z = 0 and C = 8; S2), trans-4-pentylcyclohexanecarboxylic acid (z = -2 and C = 12; S3), 4-methylcyclohexanecarboxylic acid (z = -2 and C = 8; S4), dicyclohexylacetic acid (z = -4; C = 14; S5), 4-pentylbicyclo[2.2.2]octane-1-carboxylic acid (z = -4; C = 14; S6), and lithocholic acid (z = -6; C = 24; S7). The copolymer sorbents were synthesized at three relative β-CD:diisocyanate mole ratios (i.e., 1:1, 1:2, and 1:3) using 4,4'-dicyclohexylmethane diisocyanate (CDI) and 4,4'-diphenylmethane diisocyanate (MDI). The sorption properties of the copolymer sorbents were characterized using equilibrium sorption isotherms in aqueous solution at pH 9.00 with electrospray ionization mass spectrometry. The equilibrium fraction of the unbound carboxylate anions was monitored in the aqueous phase. The sorption properties of the copolymer sorbents (i.e., Qm) were obtained from the Sips isotherm model. The Qm values generally decrease as the number of accessible β-CD inclusion sites in the copolymer framework decreases. The chemical structure of the adsorbates played an important role in their relative uptake, as evidenced by the adsorbate lipophilic surface area (LSA) and the involvement of hydrophobic effects. The copolymers exhibit molecular selective sorption of the single-component carboxylates in mixtures which suggests their application as sorbents for fractionation of mixtures of NAs. By comparison, granular activated carbon (GAC) and chitosan sorbents did not exhibit any significant molecular selective sorption relative to the copolymer materials; however, evidence of variable sorption capacity was observed among the sorbents investigated.

77 FR 30855 - Sixty-Ninth Report of the TSCA Interagency Testing Committee to the Administrator of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-23

... diisocyanates can cause contact dermatitis, skin and respiratory tract irritation, immune sensitization, and... identity or contact information unless you provide it in the body of your comment. If you send an email... Internet. If you submit an electronic comment, EPA recommends that you include your name and other contact...

Chemical and physical interpretation of MDI cure in saturated steam environments

Treesearch

David Harper; Michael P. Wolcott; Timothy Rials

1999-01-01

The cure of polymeric 4-4? diphenylmethane diisocyanate, PMDl, in wood composite manufacturing has been the subject of much research. The exact contribution of polyurethane, polyurea, and polyurete formation to PMDI/wood bonding is still debated. This study foregoes the mechanism controversy and studies the cure from a panel consolidation process. Micro-dielectric...

40 CFR 721.10581 - Brominated polyurethane prepolymers of methylene diphenyl diisocyanate (MDI) (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

..., tight-fitting half-face respirator equipped with N100 (if oil aerosols absent), R100, or P100 filters. (B) NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 (if oil...-certified powered air-purifying respirator equipped with a tight-fitting facepiece (either half-face or full...

The thermal response of HMX-TATB charges

NASA Astrophysics Data System (ADS)

Drake, R. C.

2017-01-01

One approach to achieving charge safety and performance requirements is to prepare formulations containing two (or more) explosives. The intention of this approach is that by judicious choice of explosives and binder the formulation will have the desirable features of the constituent materials. HMX and TATB have very different properties. In an attempt to achieve a formulation which has the safety and performance characteristics of TATB and HMX, respectively, a range of formulations were prepared. The thermal response of the formulations were measured in the One-Dimensional Time To Explosion (ODTX) configuration and compared to those of formulations containing only HMX and TATB. The response of the mixed formulations was found to be largely determined by the HMX component with the binder making a small contribution. A formulation with a Kel-F 800 binder had a much higher critical temperature than would have been expected based on the critical temperatures of formulations with HTPB-IPDI as the binder.

Evaluation of the cure kinetics of the wood/pMDI bondline

Treesearch

David P. Harper; Michael P. Wolcott; Timothy G. Rials

2001-01-01

Micro-dielectric analysis (µDEA) and differentia1 scanning calorimetry (DSC) were used to monitor cure of polymeric diphenyl-methane diisocyanate (pMDI) resin with wood strands in a saturated steam environment. A first-order autocatalyzed kinetic model was employed to determine kinetic parameters. The kinetics were found to follow an Arrhenius relation. A single ramp...

Opportunities and obstacles in translating evidence to policy in occupational asthma.

PubMed

Tarlo, Susan M; Arif, Ahmed A; Delclos, George L; Henneberger, Paul; Patel, Jenil

2018-06-01

Occupational asthma (OA), a common respiratory disorder in Western countries, is caused by exposures at the workplace. It is part of a broader definition of work-related asthma (WRA) that also includes pre-existing asthma aggravated by substances present in the workplace environment, and it is potentially preventable. The purpose of this paper is to illustrate preventive measures for occupational asthma by case studies. In three case studies we discuss preventive measures that have been associated with reductions in incidence of occupational asthma from natural rubber latex and from diisocyanates as supported by published literature. We also discuss challenges in relation to asthma from cleaning products in healthcare work. Several preventive measures have been associated with reduction in incidence of occupational asthma from natural rubber latex and from diisocyanates, and may provide lessons for prevention of other causes of occupational asthma. Cleaning products remain an unresolved problem at present with respect to asthma risks but potential measures include the use of safer products and safer applications such as avoidance of spray products, use of occupational hygiene methods such as improving local ventilation, and when appropriate, the use of personal protective devices. Copyright © 2017 Elsevier Inc. All rights reserved.

Opportunities and obstacles in translating evidence to policy in occupational asthma

PubMed Central

Tarlo, Susan M.; Arif, Ahmed A.; Delclos, George L.; Henneberger, Paul; Patel, Jenil

2018-01-01

Purpose Occupational asthma (OA), a common respiratory disorder in Western countries, is caused by exposures at the workplace. It is part of a broader definition of work-related asthma (WRA) that also includes pre-existing asthma aggravated by substances present in the workplace environment, and it is potentially preventable. The purpose of this paper is to illustrate preventive measures for occupational asthma by case studies. Methods In three case studies we discuss preventive measures that have been associated with reductions in incidence of occupational asthma from natural rubber latex and from diisocyanates as supported by published literature. We also discuss challenges in relation to asthma from cleaning products in healthcare work. Results and conclusions Several preventive measures have been associated with reduction in incidence of occupational asthma from natural rubber latex and from diisocyanates, and may provide lessons for prevention of other causes of occupational asthma. Cleaning products remain an unresolved problem at present with respect to asthma risks but potential measures include the use of safer products and safer applications such as avoidance of spray products, use of occupational hygiene methods such as improving local ventilation, and when appropriate, the use of personal protective devices. PMID:28434545

Development of modified poly(perfluoropropyleneoxide) urethane systems for use in liquid oxygen and in enriched 100 percent oxygen atmosphere

NASA Technical Reports Server (NTRS)

Harrison, E. S.

1973-01-01

This program consisted of two separate though related phases. The initial phase was directed toward improving the mechanical and adhesive properties of the very highly fluorinated-polyurethane resin system derived from the hydroxyl-terminated polyperfluoropropylene oxide and 6-chloro-2,4,5-trifluoro-m-phenylene diisocyanate. Various new curing agents for this system were investigated, with the goal of providing a more thermally stable crosslink (cure) mechanism to provide wider applicability and fuller utilization of the outstanding oxygen resistance of the PFPO system. Complete resistance to liquid- and gaseous-oxygen impact at presures as high as 1035 N/sq cm were attained with the use of the PFPO resin castings. The second corollary phase was directed toward investigating the feasibility and optimization of the allophanate cured, urethane extended polymer derived from hydroxyl-terminated polyperfluoropropyleneoxide and 6-chloro-2,4,5-trifluoro-m-phenylene diisocyanate, as the adhesive system for use in a weld-bond configuration for liquid oxygen tankage. The synthesis and application procedures of the adhesive system to insure liquid oxygen compatibility (under 10 kg-m loading), and the development of procedures and techniques to provide high quality weld-bonded joint configurations were studied.

Toluene diisocyanate increases airway responsiveness to substance P and decreases airway neutral endopeptidase.

PubMed

Sheppard, D; Thompson, J E; Scypinski, L; Dusser, D; Nadel, J A; Borson, D B

1988-04-01

Substance P and related tachykinins contribute to the airway hyperresponsiveness caused by toluene diisocyanate (TDI) in guinea pigs. Neutral endopeptidase (NEP) is an important modulator of substance P-induced responses. To test the hypothesis that exposure to TDI would increase responsiveness to substance P by inhibiting activity of this enzyme, we determined the dose of substance P required to increase pulmonary resistance by 200% above baseline (PD200) before and after administration of the pharmacologic inhibitor phosphoramidon in guinea pigs studied 1 h after a 1-h exposure to air or 3 ppm TDI. TDI exposure increased responsiveness to substance P significantly. However, phosphoramidon caused a significantly greater leftward shift of the substance P dose-response curve in air-exposed animals than it did in TDI-exposed animals, so that after phosphoramidon, mean values of PD200 in animals exposed to air or TDI did not differ. Tracheal NEP activity was significantly less after exposure to TDI than after exposure to air, whereas activity in the esophagus was the same in both groups. These results suggest that TDI exposure increases the bronchoconstrictor responsiveness of guinea pigs to substance P, in large part through inhibition of airway NEP.

Toluene diisocyanate increases airway responsiveness to substance P and decreases airway neutral endopeptidase.

PubMed Central

Sheppard, D; Thompson, J E; Scypinski, L; Dusser, D; Nadel, J A; Borson, D B

1988-01-01

Substance P and related tachykinins contribute to the airway hyperresponsiveness caused by toluene diisocyanate (TDI) in guinea pigs. Neutral endopeptidase (NEP) is an important modulator of substance P-induced responses. To test the hypothesis that exposure to TDI would increase responsiveness to substance P by inhibiting activity of this enzyme, we determined the dose of substance P required to increase pulmonary resistance by 200% above baseline (PD200) before and after administration of the pharmacologic inhibitor phosphoramidon in guinea pigs studied 1 h after a 1-h exposure to air or 3 ppm TDI. TDI exposure increased responsiveness to substance P significantly. However, phosphoramidon caused a significantly greater leftward shift of the substance P dose-response curve in air-exposed animals than it did in TDI-exposed animals, so that after phosphoramidon, mean values of PD200 in animals exposed to air or TDI did not differ. Tracheal NEP activity was significantly less after exposure to TDI than after exposure to air, whereas activity in the esophagus was the same in both groups. These results suggest that TDI exposure increases the bronchoconstrictor responsiveness of guinea pigs to substance P, in large part through inhibition of airway NEP. PMID:2450892

Two cases of paraoccupational asthma due to toluene diisocyanate (TDI).

PubMed

De Zotti, R; Muran, A; Zambon, F

2000-12-01

Two cases of paraoccupational asthma caused by toluene diisocyanate (TDI) are reported. The first patient was a metal worker in a machine shop situated near a factory producing polyurethane foam. Symptoms at work were not explainable by any specific exposure to irritants or allergens in the work site. As the patient recalled previous occasional work in the adjacent polyurethane factory with accompanying worsening of respiratory symptoms, a specific inhalation (SIC) test was performed with TDI, which confirmed the diagnosis of TDI asthma. The second case was a woman working part time as a secretary in the offices of her son's factory for varnishing wooden chairs. TDI was present in the products used in the varnishing shed. The SIC test confirmed the diagnosis of TDI asthma, despite the fact that the patient's job did not present risk of exposure to the substance. In both patients, symptoms disappeared when further exposure was avoided. These two cases confirm that paraoccupational exposure to TDI must be considered when evaluating patients with asthma not mediated by immunoglobulin E. They also suggest the need for more prospective studies evaluating the health risk for the general population living near polyurethane factories or other firms that use TDI.

Gelatin-based Hydrogel Degradation and Tissue Interaction in vivo: Insights from Multimodal Preclinical Imaging in Immunocompetent Nude Mice.

PubMed

Tondera, Christoph; Hauser, Sandra; Krüger-Genge, Anne; Jung, Friedrich; Neffe, Axel T; Lendlein, Andreas; Klopfleisch, Robert; Steinbach, Jörg; Neuber, Christin; Pietzsch, Jens

2016-01-01

Hydrogels based on gelatin have evolved as promising multifunctional biomaterials. Gelatin is crosslinked with lysine diisocyanate ethyl ester (LDI) and the molar ratio of gelatin and LDI in the starting material mixture determines elastic properties of the resulting hydrogel. In order to investigate the clinical potential of these biopolymers, hydrogels with different ratios of gelatin and diisocyanate (3-fold (G10_LNCO3) and 8-fold (G10_LNCO8) molar excess of isocyanate groups) were subcutaneously implanted in mice (uni- or bilateral implantation). Degradation and biomaterial-tissue-interaction were investigated in vivo (MRI, optical imaging, PET) and ex vivo (autoradiography, histology, serum analysis). Multimodal imaging revealed that the number of covalent net points correlates well with degradation time, which allows for targeted modification of hydrogels based on properties of the tissue to be replaced. Importantly, the degradation time was also dependent on the number of implants per animal. Despite local mechanisms of tissue remodeling no adverse tissue responses could be observed neither locally nor systemically. Finally, this preclinical investigation in immunocompetent mice clearly demonstrated a complete restoration of the original healthy tissue.

Production of high molecular weight polylactic acid

DOEpatents

Bonsignore, Patrick V.

1995-01-01

A degradable high molecular weight poly(lactic acid). A poly(lactic acid) has a terminal end group of one of carboxyl or hydroxyl groups with low molecular weight poly(lactic acid) units coupled with linking agents of di-isocyanates, bis-epoxides, bis-oxazolines and bis-ortho esters. The resulting high molecular weight poly(lactic acid) can be used for applications taking advantage of the improved physical properties.

Elucidating How Wood Adhesives Bond to Wood Cell Walls using High-Resolution Solution-State NMR Spectroscopy

Treesearch

Daniel J. Yelle

2013-01-01

Some extensively used wood adhesives, such as pMDI (polymeric methylene diphenyl diisocyanate) and PF (phenol formaldehyde) have shown excellent adhesion properties with wood. However, distinguishing whether the strength is due to physical bonds (i.e., van der Waals, London, or hydrogen bond forces) or covalent bonds between the adherend and the adhesive is not fully...

Highly fluorinated polyurethanes

NASA Technical Reports Server (NTRS)

Stump, E. C., Jr.; Rochow, S. E. (Inventor)

1972-01-01

New polyurethanes containing a high degree of fluorine atoms are reported. The presence of the fluorine atoms in the polyurethane resins provides material having good thermal stability and chemical resistance. These polyurethanes are derived from a new hydroxy-terminated perfluoro polyether. The hydroxy terminated material is reacted with a diisocyanate to produce the polyurethanes. The polyurethanes can be used to form seals, coatings, potting material, hoses and the like.

Delineating pMDI model reactions with loblolly pine via solution-state NMR spectroscopy. Part 1, Catalyzed reactions with wood models and wood polymers

Treesearch

Daniel J. Yelle; John Ralph; Charles R. Frihart

2011-01-01

To better understand adhesive interactions with wood, reactions between model compounds of wood and a model compound of polymeric methylene diphenyl diisocyanate (pMDI) were characterized by solution-state NMR spectroscopy. For comparison, finely ground loblolly pine sapwood, milled-wood lignin and holocellulose from the same wood were isolated and derivatized with...

International Traffic in Arms Regulations (ITAR), (22 CFR 120-130)

DTIC Science & Technology

1996-06-01

Butadienenitrileoxide (BNO); (6) Catocene, N-butyl- ferrocene and other ferrocene derivatives; (7) 3-nitraza-l,5 pentane diisocyanate; (8) Bis(2,2...Tris-l-(2-methyl)aziridinyl phosphine oxide (MAPO), bis(2-methyl aziridinyl) 2-(2-hydroxypropanoxy) propylamino phosphine oxide (BOBBA 8), and...other MAPO derivatives; (22) Bis(2-methyl aziridinyl) methylamino phosphine oxide (methyl BAPO); (23) Organo-metallic coupling agents, specifi

Biomarkers of exposure, antibodies, and respiratory symptoms in workers heating polyurethane glue.

PubMed Central

Skarping, G; Dalene, M; Svensson, B G; Littorin, M; Akesson, B; Welinder, H; Skerfving, S

1996-01-01

OBJECTIVES: The pathogenic basis of respiratory disorders associated with isocyanates are still obscure. One reason for this is the lack of good estimates of human exposure. In this study exposure was estimated by measurement of isocyanate metabolites in biological samples. METHODS: In a factory using isocyanate based polyurethane (PUR) glue, isocyanate concentrations in air were measured by liquid chromatography. Samples from 174 employees were analysed for metabolites of 4,4'-methylene diphenyl diisocyanate (MDI) in plasma (P-MDX) and urine (U-MDX). After hydrolysis, 4,4'-methylenedianiline was measured by gas chromatography-mass spectrometry (GC-MS). The employees were screened for work related respiratory symptoms and tested for specific immunoglobulin E (IgE) and IgG antibodies directed against isocyanate conjugated to human serum albumin. RESULTS: The time weighted isocyanate concentrations in air were low (MDI < 0.2-7; hexamethylene diisocyanate (HDI) < 0.1-0.7; 2,6-toluene diisocyanate (TDI) < 0.1 microgram/m3). All subjects had detectable P-MDX and U-MDX. There were significant associations between the estimates of exposure to thermal degradation products of an MDI based glue and P-MDX (range < or = 0.10-5.5 micrograms/l); and U-MDX (< or = 0.04-5.0 micrograms/g creatinine); in cases of heavy exposure. P-MDX and U-MDX were associated with each other (r = 0.64; P = 0.0001), work related symptoms (P-MDX: P = 0.03; Mann-Whitney U test), and serum concentrations of MDI specific IgG antibodies (r = 0.26; P = 0.0007). Unexpectedly, high P-MDX and U-MDX concentrations were also encountered in workers cutting textile (P-MDX 2.4-4.5 micrograms/l; U-MDX 0.81-3.8 micrograms/g creatinine); the reason is still unknown. Equally unexpected, there were significant negative associations between P-MDX and liver function tests. CONCLUSIONS: The results clearly show the value of biomarkers for isocyanate exposure; in particular, P-MDX is useful. Further, these results show the risk connected with thermal degradation of PUR. PMID:8704859

Field comparison of air sampling methods for monomeric and polymeric 1,6-hexamethylene diisocyanate.

PubMed

Thomasen, Jennifer M; Fent, Kenneth W; Reeb-Whitaker, Carolyn; Whittaker, Stephen G; Nylander-French, Leena A

2011-03-01

This study was to critically compared 13 different air samplers for their ability to monitor air exposures to monomeric and polymeric 1,6-hexamethylene diisocyanate (HDI) in the automotive refinishing industry. Using both fast- and slow-drying clearcoat, we tested the following types of samplers: single- and dual-stage 37-mm polypropylene (PP) and polystyrene (PS) samplers (open- and closed-face), IOM (with plastic and stainless steel inserts), OSHA42, IsoChek, and WA-DOSH samplers. Midget impingers with frit were used as reference samplers. We observed the PP, PS, and IOM samplers to measure greater levels of HDI monomer and biuret when a fast-drying clearcoat was applied compared with a slow-drying clearcoat. When a slow-drying clearcoat was applied, the open-face PP and PS samplers measured significantly more monomeric and polymeric HDI (2-fold; p < 0.003) than the closed-face PP and PS samplers. We determined that significantly more monomeric and polymeric HDI were measured by impingers (1.3-1.9-fold) compared with single-stage PP/PS (N = 59), dual-stage PP/PS (N = 59), or IOM (N = 24) samplers. However, when stratified by cassette characteristics, the open-face single-stage PP and PS samplers performed equally to the impingers for HDI monomer when a fast-drying clearcoat was applied, and for all analytes when a slow-drying clearcoat was applied. Significantly higher HDI monomer concentrations (1.2-3.1-fold; p = 0.001) were measured with OSHA42 compared with the impinger. The IsoChek did not detect HDI monomer, and of the three samplers analyzed by laboratories other than UNC (i.e., OSHA42, IsoChek, and WA-DOSH), the WA-DOSH was in the best agreement with the impingers. The influence of clearcoat drying time on the sampler's ability to measure monomeric and polymeric HDI emphasizes the importance of the speciation of diisocyanates in chemical analysis and the careful consideration for the selection of the air sampler to be used when measuring exposures during automotive spray painting.

Analysis of the interrelationship of the pulmonary irritation and elicitation thresholds in rats sensitized with 1,6-hexamethylene diisocyanate (HDI)

PubMed Central

Pauluhn, Jürgen

2015-01-01

Abstract This paper summarizes a range of experimental data central for developing a science-based approach for hazard identification of monomeric and polymeric aliphatic 1,6-hexamethylene diisocyanate (HDI). The dose–response curve of HDI-induced pulmonary responses in naïve or dermally sensitized rats after one or several inhalation priming exposures was examined in the Brown Norway (BN) rat asthma model. Emphasis was directed to demonstrate the need and the difficulty in selecting an appropriate pulmonary dose when much of the inhaled chemically reactive vapor may concentration dependently be retained in the upper airways of obligate nose-breathing rats. The course taken acknowledges the experimental challenges in identifying an elicitation threshold for HDI-monomer near or above the saturated vapor concentration or in the presence of a HDI-polymer aerosol. The inhalation threshold dose on elicitation was determined based on a fixed concentration (C) × variable exposure duration (t) protocol for improving inhalation dosimetry of the lower airways. Neutrophilic granulocytes (PMN) in bronchoalveolar lavage (BAL) fluid in equally inhalation primed naïve and dermally sensitized rats were used to define the inhalation elicitation threshold C × t. Sensitized rats elaborated markedly increased PMN challenged sensitized rats relative to equally challenged naïve rats at 5625 mg HDI/m3 × min (75 mg/m3 for 75 min). PMN were essentially indistinguishable at 900 mg HDI/m3 × min. By applying adjustment factors accounting for both inter-species differences in inhalation dosimetry and intra-species susceptibility, the workplace human-equivalent threshold C × t was estimated to be in the range of the current ACGIH TLV® of HDI. Thus, this rat “asthma” model was suitable to demonstrate elicitation thresholds for HDI-vapor after one or several inhalation priming exposures and seems to be suitable to derive occupational exposure values (OELs) for diisocyanates in general. PMID:25924102

Field validation of the dnph method for aldehydes and ketones. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Workman, G.S.; Steger, J.L.

1996-04-01

A stationary source emission test method for selected aldehydes and ketones has been validated. The method employs a sampling train with impingers containing 2,4-dinitrophenylhydrazine (DNPH) to derivatize the analytes. The resulting hydrazones are recovered and analyzed by high performance liquid chromatography. Nine analytes were studied; the method was validated for formaldehyde, acetaldehyde, propionaldehyde, acetophenone and isophorone. Acrolein, menthyl ethyl ketone, menthyl isobutyl ketone, and quinone did not meet the validation criteria. The study employed the validation techniques described in EPA method 301, which uses train spiking to determine bias, and collocated sampling trains to determine precision. The studies were carriedmore » out at a plywood veneer dryer and a polyester manufacturing plant.« less

Properties of Multiphase Polyurethane Systems.

DTIC Science & Technology

1983-07-01

segment - diphenylmethane-diisocyanate/ N - methyldiethanolamine (MDI/ MDEA ). Each polymer was synthesized using a two step reaction technique. The number...OF MULTIPHASE POLYURETHANE SYSTEMS Final Report for Period July 1, 1982-June 30, 1983 Naval Air Systems Command Code 5304 C2 ONavy Contract # N 00019...and COB, UA groups. The existence of 3-dimensional hydrogen bonding (two C-O groups bonded to one N -H group) should shift the COB,UA peak to lower

Production of high molecular weight polylactic acid

DOEpatents

Bonsignore, P.V.

1995-11-28

A degradable high molecular weight poly(lactic acid) is described. The poly(lactic acid) has a terminal end group of one of carboxyl or hydroxyl groups with low molecular weight poly(lactic acid) units coupled with linking agents of di-isocyanates, bis-epoxides, bis-oxazolines and bis-ortho esters. The resulting high molecular weight poly(lactic acid) can be used for applications taking advantage of the improved physical properties.

40 CFR 302.4 - Designation of hazardous substances.

Code of Federal Regulations, 2013 CFR

2013-07-01

... aldehyde 7421-93-4 2 1 (0.454) ENDRIN AND METABOLITES N.A. 2 ** Endrin, & metabolites 72-20-8 1,2,4 P051 1... diisocyanate 101-68-8 3 5000 (2270) Methyl ethyl ketone 78-93-3 3,4 U159 5000 (2270) Methyl ethyl ketone... U138 100 (45.4) Methyl isobutyl ketone 108-10-1 3,4 U161 5000 (2270) Methyl isocyanate 624-83-9 3,4...

40 CFR 302.4 - Designation of hazardous substances.

Code of Federal Regulations, 2012 CFR

2012-07-01

... aldehyde 7421-93-4 2 1 (0.454) ENDRIN AND METABOLITES N.A. 2 ** Endrin, & metabolites 72-20-8 1,2,4 P051 1... diisocyanate 101-68-8 3 5000 (2270) Methyl ethyl ketone 78-93-3 3,4 U159 5000 (2270) Methyl ethyl ketone... U138 100 (45.4) Methyl isobutyl ketone 108-10-1 3,4 U161 5000 (2270) Methyl isocyanate 624-83-9 3,4...

40 CFR 302.4 - Designation of hazardous substances.

Code of Federal Regulations, 2014 CFR

2014-07-01

... aldehyde 7421-93-4 2 1 (0.454) ENDRIN AND METABOLITES N.A. 2 ** Endrin, & metabolites 72-20-8 1,2,4 P051 1... diisocyanate 101-68-8 3 5000 (2270) Methyl ethyl ketone 78-93-3 3,4 U159 5000 (2270) Methyl ethyl ketone... U138 100 (45.4) Methyl isobutyl ketone 108-10-1 3,4 U161 5000 (2270) Methyl isocyanate 624-83-9 3,4...

Testing of household products and materials for emission of toluene diisocyanate.

PubMed

Kelly, T J; Myers, J D; Holdren, M W

1999-06-01

Polyurethane products were subjected to chamber testing to determine their emission rates of 2,4- and 2,6-toluene diisocyanate (TDI). The polyurethane (PU) products included carpet padding, furniture cushions, sheet foam, varnishes, and sealants, as well as a commercially-applied water sealant product for concrete that contained up to 4 percent TDI by weight. The PU products were screened in a 9-L glass chamber, under elevated temperature and chamber loading conditions, using both a time-integrated sampling and analysis method specific for TDI and a continuous but non-specific real-time monitor for isocyanates. None of the products normally found in residences showed a positive response in the screening tests, indicating that TDI emissions and consequently toxic effects from such products are negligible. However, the commercially-applied water sealant gave a positive response in the screening test. Further testing of that product at realistic temperatures showed initial TDI emission rates of about 300,000 micrograms/m2/hr, with emissions lasting only one hour or less. At 21 and 27 degrees C, about 1 percent and 5 percent, respectively, of the TDI content of the product was released to the air. The emitted TDI was predominantly the 2,6-isomer, although the TDI originally present in the product was predominantly the 2,4-isomer.

MALDI MS-based Composition Analysis of the Polymerization Reaction of Toluene Diisocyanate (TDI) and Ethylene Glycol (EG).

PubMed

Ahn, Yeong Hee; Lee, Yeon Jung; Kim, Sung Ho

2015-01-01

This study describes an MS-based analysis method for monitoring changes in polymer composition during the polyaddition polymerization reaction of toluene diisocyanate (TDI) and ethylene glycol (EG). The polymerization was monitored as a function of reaction time using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI TOF MS). The resulting series of polymer adducts terminated with various end-functional groups were precisely identified and the relative compositions of those series were estimated. A new MALDI MS data interpretation method was developed, consisting of a peak-resolving algorithm for overlapping peaks in MALDI MS spectra, a retrosynthetic analysis for the generation of reduced unit mass peaks, and a Gaussian fit-based selection of the most prominent polymer series among the reconstructed unit mass peaks. This method of data interpretation avoids errors originating from side reactions due to the presence of trace water in the reaction mixture or MALDI analysis. Quantitative changes in the relative compositions of the resulting polymer products were monitored as a function of reaction time. These results demonstrate that the mass data interpretation method described herein can be a powerful tool for estimating quantitative changes in the compositions of polymer products arising during a polymerization reaction.

New polyurethane/docosane microcapsules as phase-change materials for thermal energy storage.

PubMed

Felix De Castro, Paula; Shchukin, Dmitry G

2015-07-27

Polyurethane microcapsules were prepared by mini-emulsion interfacial polymerization for encapsulation of phase-change material (n-docosane) for energy storage. Three steps were followed with the aim to optimize synthesis conditions of the microcapsules. First, polyurethane microcapsules based on silicone oil core as an inert template with different silicone oil/poly(ethylene glycol)/4,4'-diphenylmethane diisocyanate wt % ratio were synthesized. The surface morphology of the capsules was analyzed by scanning electronic microscopy (SEM) and the chemical nature of the shell was monitored by Fourier transform infrared spectroscopy (FT-IR). Capsules with the silicone oil/poly(ethylene glycol)/4,4'-diphenylmethane diisocyanate 10/20/20 wt % ratio showed the best morphological features and shell stability with average particle size about 4 μm, and were selected for the microencapsulation of the n-docosane. In the second stage, half of the composition of silicone oil was replaced with n-docosane and, finally, the whole silicone oil content was replaced with docosane following the same synthetic procedure used for silicone oil containing capsules. Thermal and cycling stability of the capsules were investigated by thermal gravimetric analysis (TGA) and the phase-change behavior was evaluated by differential scanning calorimetry (DSC). © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Field Evaluation of Solvent-Free Sampling with Di-n-butylamine for the Determination of Airborne Monomeric and Oligomeric 1,6-Hexamethylene Diisocyanate

DTIC Science & Technology

2014-03-27

cause contact dermatitis , asthma, and hypersensitivity pneumonitis; the most common adverse health outcome associated with isocyanate exposure is...linked to allergic contact dermatitis in humans and respiratory sensitization in animals. Chronic dermal exposure has resulted in skin irritation and...derivatization stabilizes the highly reactive isocyanates and enhances recovery of the isocyanates that do not come into contact with the derivatization

Personnel Exposure to Airborne Isocyanates and Solvents During Shipboard Painting With 2-Pack Polyurethane Paints

DTIC Science & Technology

2008-12-01

contain low volatility isocyanate prepolymers in addition to small quantities of volatile isocyanate monomers [2,3]. The monomers may become airborne as...vapour whilst the non-volatile prepolymers and partially cured oligomers may form aerosols during spray painting and sanding of the painted surface...JL (1992) “ Prepolymers of hexamethylene diisocyanate as a cause of occupational asthma” J. Allergy Clinical Immunol. 91 850-61. 5. Redlich CA, Bello

t-Butyl-Oxycarbonylated Diamines as Building Blocks for Isocyanate-Free Polyurethane/Urea Dispersions and Coatings.

PubMed

Ma, Shuang; Zhang, Huiyi; Sablong, Rafaël J; Koning, Cor E; van Benthem, Rolf A T M

2018-05-01

t-Butyl-oxycarbonylated diamines ("di-Boc-carbamates") are investigated as dicarbamate monomers for diamine/dicarbamate polymerizations. Polyureas (PUs) and polyurethanes (PURs) with high molecular weights are prepared from stoichiometric polymerizations of diamines or diols with N-N'-di-t-butyl-oxycarbonyl isophorone diamine (DiBoc-IPDC) using KOt-Bu as a catalyst, while gelation is observed when an excess of DiBoc-IPDC is used with respect to the diamines or diols. Stable dispersions are obtained from PUs and PURs with 3,3'-diamino-N-methyldipropylamine (DMDPA) as internal dispersing agent. The corresponding PU-based coatings exhibit superior mechanical properties and solvent resistances compared to the polyurethane urea coatings synthesized from diols, DiBoc-IPDC, and DMDPA. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Analytical procedures for environmental quality control. Volume 2. Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, L.K.; Wang, M.H.S.

1989-01-15

This report covers sixteen important documents. Some examples are: The determination of the maximum total trihalomethane potential; Nationwide approval of alternative test procedure for analysis of trihalomethanes; Volatile organic compounds in eater by purge and trap capillary column gas chromatography with photoionization and electrolytic conductivity detectors in series; Analysis of organohalide pesticides and arclors in drinking water by microextraction and gas chromatography; Testing for lead in school drinking water; Simplified methods for food and feed testing; Determination of nitroaromatic compounds and isophorone in industrial and municipal wastewaters; Sampling for giardia and/or cryptosporidium; determination of TCDD in industrial and municipal wastewaters;more » Determination of volatile organics in industrial and municipal wastewaters; Determination of polynuclear aromatic hydrocarbons in industrial and municipal wastewaters.« less

Polyurethanes from fluoroalkyl propyleneglycol polyethers

NASA Technical Reports Server (NTRS)

Trischler, F. D. (Inventor)

1969-01-01

A description is given of highly stable polyurethane polymers prepared by reacting a polyether with a diisocyanate. Compounded stocks of these polymers may be shaped and cured in conventional equipment used in the rubber industry. The solutions are dispersed gels prepared from the polymers and may be used for forming supported or unsupported films for coating fabrics or solid surfaces, and for forming adhesive bonds between a wide variety of plastics, elastomers, fabrics, metals, wood, leather, ceramics and the like.

Synthesis of Polyurethanes Membranes from Rubber Seed Oil and Methylene Diphenyl Diisocyanates (MDI)

NASA Astrophysics Data System (ADS)

Marlina; Nurman, S.; Saleha, S.; Fitriani; Thanthawi, I.

2017-03-01

Rubber seed oil and methylene diphenyl diisocyanates (MDI) based polyurethane membrane has been prepared in this study. The main objective of this research is manufacture of polyurethane membranes from avocado seed oil, as a filter of this membrane use as a filter of metals from water such as mercury (Hg). In this study, the polyurethane membrane had been synthesized by varying compositions of rubber seed oil and MDI, with ratios of 10:0.2; 10:0.4; 10:0.6; 10:0.8; 10:1.0; 10:1.2; 10:1.4; 10:1.6; 10:1.8 and 10:2.0 (v/w) at 80°C and 170°C as polymerization and curing temperatures, respectively. Optimum polyurethane membrane was obtained at rubber seed oil: MDI 10: 0.8 v/w, it was dry, non-sticky, smooth and blackish brown. The membrane flux was 5,8307 L / m2.h.bar and rejection factor was 35,3015 %. The results of characterization indicated the formation of urethane bonds (NH at 3480 cm-1, C=O at 1620 cm-1, CN at 1374 cm-1, -OC-NH- at 1096 cm-1 and no -NCO at 2270 cm-1), the value of Tg was 55°C. The polyurethane membrane which treated at the optimum treatment conditions were used to the filter of metals from water such as mercury (Hg).

Adhesion of nitrile rubber (NBR) to polyethylene terephthalate (PET) fabric. Part 1: PET surface modification by methylenediphenyl di-isocyanate (MDI)

NASA Astrophysics Data System (ADS)

Razavizadeh, Mahmoud; Jamshidi, Masoud

2016-01-01

Fiber to rubber adhesion is an important subject in rubber composite industry. It is well known that surface physical, mechanical and chemical treatments are effective methods to improve interfacial bonding. Ultra violet (UV) light irradiation is an efficient method which is used to increase interfacial interactions. In this research UV assisted chemical modification of PET fabric was used to increase its bonding to nitrile rubber (NBR). NBR is perfect selection to produce fuel and oil resistant rubber parts but it has weak bonding to fabrics. For this purpose at first, the PET fabric was carboxylated under UV irradiation and then methylenediphenyl diisocyanate (MDI) was reacted and grafted to carboxylated PET. T-peel test was used to evaluate PET fabric to NBR bonding strength. Attenuated total reflectance-Fourier transform infrared spectroscopy (FTIR-AT) was used to assess surface modifications of the PET fabrics. The chemical composition of the PET surfaces before and after carboxylation and MDI grafting was investigated by X-ray photoelectron spectroscopy (XPS). It was found that at vulcanizing temperature of 150 °C, carboxylation in contrary to MDI grafting, improved considerably PET to NBR adhesion. Finally effect of curing temperature on PET to NBR bonding strength was determined. It was found that increasing vulcanizing temperature to 170 °C caused considerable improvement (about 134%) in bonding strength.

A follow up study of occupational exposure to 4,4'-methylene-bis(2-chloroaniline) (MbOCA) and isocyanates in polyurethane manufacture in the UK.

PubMed

Keen, C; Coldwell, M; McNally, K; Baldwin, P; McAlinden, J; Cocker, J

2012-08-13

This is a follow up survey of exposure to 4,4'-methylene-bis(2-chloroaniline) (MbOCA) and isocyanates in the UK polyurethane industry. Urine samples (n=446) were collected from 90 different workers. MbOCA levels were below the limit of detection in 170 samples and 26 were above the UK Biological Monitoring Guidance Value (BMGV) of 15 μmol MbOCA/mol creatinine. Detailed advice and guidance was given to each workplace at the end of the survey in 2008 and the 90% value reduced from 10 to 3 μmol MbOCA/mol creatinine in samples collected since. There was a positive correlation between glove contamination and urinary MbOCA and levels were dependent upon individual working practices especially how gloves were used. Of the 446 samples analysed for urinary metabolites of toluene diisocyanate 280 were below the detection limit and 126 were above the BMGV (1 μmol/mol creatinine). Of the 326 urine samples that were analysed for metabolites of methylenediphenyl diisocyanate, 270 were below the detection limit and 13 were above the BMGV for isocyanates. There was no correlation between urinary levels of isocyanates and MbOCA suggesting different routes of absorption, most likely inhalation and dermal respectively. Crown Copyright © 2011. Published by Elsevier Ireland Ltd. All rights reserved.

Response of Polyurethane to Shock Waves: An Experimental Investigation

NASA Astrophysics Data System (ADS)

Jayaram, V.; Rao, Keshava Subba; Thanganayaki, N.; Kumara, H. K. T.; Reddy, K. P. J.

Formation of polyurethane (PU) in vacuum environment and controlling density of polyurethane foams are the present day challenges. Polyurethane exists in numerous forms ranging from flexible to rigid and lightweight foams to tough, stiff elastomers [1]. PU can be used to produce lightweight foams for insulation or hard rubber used as wheels to transport heavy loads and it can be used in high pressure applications. The largest volumes of commercial PU elastomers are made from toluene diisocyanate (TDI) or diphenylmethane-4, 4'-diisocyanate (MDI) [2]. Linear polyurethanes can be processed into final products by any of the standard thermoplastic processes (injection molding, extrusion, thermoforming) as well as by low pressure cast processes in presence of catalysts. Tin, tetrabutyl titanate and zirconium chelates are few effective catalysts used to produce polyurethane for particular application [3]. Thermoset elastomers are formed due to irreversible cross-links, when polymers are chemically cured. Highly porous biodegradable PU was synthesized by thermally induced phase separation technique used in tissue engineering and also in bio-degradable based fluids [4]. Properties of PU like hardness, stress/strain modulus, tear strength etc, was determine using ASTM (American Society for Testing and Materials) standard methods. PU possesses extremely high mechanical properties, excellent abrasion, tear and extrusion resistance. It has outstanding low-temperature limit (-600C) and high temperature limit up to (1500C).

Surface modification of calcined kaolin with toluene diisocyanate based on high energy ball milling

NASA Astrophysics Data System (ADS)

Yuan, Yongbing; Chen, Hongling; Lin, Jinbin; Ji, Yan

2013-11-01

The surface of calcined kaolin particle was modified with toluene diisocyanate (TDI) by using high energy ball milling. The prepared hybrids were characterized by FT-IR, MAS NMR, thermal analysis (TGA-DSC), static water contact angle (CA), apparent viscosity and transmission electron microscopy (TEM). FT-IR and MAS NMR spectra demonstrated that TDI molecules were chemically anchored to kaolin surface after modification. The results of thermal analysis showed that the maximum grafting ratio reached up to 446.61% when the mass ratio of TDI/kaolin was 0.5:1.0, and CA measurements revealed that the resultant hybrids exhibited strong hydrophobicity (148.82°). Apparent viscosity and TEM were employed to examine the dispersion properties of blank and modified kaolin particles in poly (dimenthylsiloxane) matrix. The results illustrated that the dispersion stability depended strongly on the grafting ratio of TDI, neither too low nor too high achieved uniform and stable dispersion, and the favorable grafting ratio was obtained when the mass ratio of TDI/kaolin was 0.2:1.0. Further modification of TDI/kaolin (mass ration of TDI/kaolin, 1.0:1.0) particles with bis(aminopropyl)-terminated-poly(dimethylsiloxane) (APS) was also investigated. TEM evidenced that the dispersion properties of the obtained TDI/APS/kaolin particles were remarkably improved in octamethyl cyclotetrasiloxane compared with the original TDI/kaolin particles.

FTIR spectroscopic characterization of polyurethane-urea model hard segments (PUUMHS) based on three diamine chain extenders

NASA Astrophysics Data System (ADS)

Zhang, Shijie; Ren, Zhiyong; He, Suqing; Zhu, Yan; Zhu, Chengshen

2007-01-01

Six polyurethane-urea model hard segments (PUUMHS) were prepared by a solution method based, respectively, on two isocyanates: 4,4'-methylene-diphenyl-diisocyanate (MDI), 4,4'-methylene-dicyclohexyl diisocyanate (HMDI) and three amine chain extenders: ethylene diamine (EDA), methylene-bis-ortho-chloroaniline (MOCA), 2,4-diamino-3,5-dimethylsuphylchlorobenzene (DDSCB). FTIR was used to study their spectroscopic characterization. The main FTIR bands of the six samples were assigned and compared. It was found that most of N-H and C dbnd O are H-bonded in these PUUMHS. However, the N-H in three MDI based PUUMHS is all in the stronger H-bond state than that in their corresponding HMDI based while the C dbnd O in three HMDI based PUUMHS is all in the stronger H-bond state than that in their corresponding MDI based, respectively. In addition, the order of the H-bond strength in HMDI based PUUMHS is MOCA, DDSCB and EDA whether according to νN sbnd H or νC dbnd O band wavenumbers, which is, however, different from that in MDI based PUUMHS. Moreover, the HMDI based PUUMHS shows obvious double amide III bands while the MDI based has only prominent one. The results are discussed according mainly to the different characteristics of the three chain extenders as well as the structure difference between MDI and HMDI.

Reaction products of hexamethylene diisocyanate vapors with “self” molecules in the airways of rabbits exposed via tracheostomy

PubMed Central

Wisnewski, Adam V.; Kanyo, Jean; Asher, Jennifer; Goodrich, James A.; Barnett, Grace; Patrylak, Lyn; Liu, Jian; Redlich, Carrie A.; Nassar, Ala F.

2018-01-01

Hexamethylenediisocyanate (HDI) is a widely used aliphatic diisocyanate and a well-recognized cause of occupational asthma.“Self” molecules (peptides/proteins) in the lower airways, susceptible to chemical reactivity with HDI, have been hypothesized to play a role in asthma pathogenesis and/or chemical metabolism, but remain poorly characterized.This study employed unique approaches to identify and characterize “self” targets of HDI reactivity in the lower airways. Anesthetized rabbits free breathed through a tracheostomy tube connected to chambers containing either, O2, or O2 plus ~200 ppb HDI vapors. Following 60 minutes of exposure, the airways were lavaged and the fluid was analyzed by LC-MS and LC-MS/MS.The low-molecular weight (<3 kDa) fraction of HDI exposed, but not control rabbit bronchoalveolar lavage (BAL) fluid identified 783.26 and 476.18 m/z [M+H]+ ions with high energy collision-induced dissociation (HCD) fragmentation patterns consistent with bis glutathione (GSH)-HDI and mono(GSH)-HDI. Proteomic analyses of the high molecular weight (>3 kDa) fraction of exposed rabbit BAL fluid identified HDI modification of specific lysines in uteroglobin (aka clara cell protein) and albumin.In summary, this study utilized a unique approach to chemical vapor exposure in rabbits, to identify HDI reaction products with “self” molecules in the lower airways. PMID:28489470

Toluene diisocyanate concentration investigation among TDI-related factories in Taiwan and their relations to the type of industry.

PubMed

Yeh, Hui-Jung; Shih, Tung-Sheng; Tsai, Perng-Jy; Chang, Ho-Yuan

2002-03-01

To determine nationwide 2,4- and 2,6-toluene diisocyanates (TDI) concentrations among polyurethane (PU) resin, PU foam, and other TDI-related industries in Taiwan. The ratios of 2,4-/2,6-TDI and the noncarcinogenic risk among these three industries were also investigated. Personal and fixed-area monitoring of TDI concentrations as well as questionnaires were performed for 26 factories in Taiwan. The modified OHSA 42 method was applied in sampling and analysis. Noncarcinogenic hazard index was estimated for these three industries based on the average concentration measurements. Significant differences of TDI concentrations were found among the three industry categories. For personal monitoring, PU foam was found to have the highest TDI levels [18.6 (+/-33.6) and 22.1 (+/-42.3) ppb for 2,4- and 2,6-TDI], Others average [8.3 (+/-18.9) and 10.2 (+/-17.2) ppb], and PU resin lowest [2.0 (+/-3.5) and 0.7 (+/-1.2) ppb]. The estimated average hazard indices were found to be 310-3310. A substantial percentage of airborne TDI concentrations among in Taiwan industries exceeded current TDI occupational exposure limit, and significant difference of TDI levels were found among the three industry categories. The control remedy for the tasks of charging and foaming should be enforced with the highest priority. A separate 2,6-TDI exposure standard is warranted.

Using machine learning to identify air pollution exposure profiles associated with early cognitive skills among U.S. children.

PubMed

Stingone, Jeanette A; Pandey, Om P; Claudio, Luz; Pandey, Gaurav

2017-11-01

Data-driven machine learning methods present an opportunity to simultaneously assess the impact of multiple air pollutants on health outcomes. The goal of this study was to apply a two-stage, data-driven approach to identify associations between air pollutant exposure profiles and children's cognitive skills. Data from 6900 children enrolled in the Early Childhood Longitudinal Study, Birth Cohort, a national study of children born in 2001 and followed through kindergarten, were linked to estimated concentrations of 104 ambient air toxics in the 2002 National Air Toxics Assessment using ZIP code of residence at age 9 months. In the first-stage, 100 regression trees were learned to identify ambient air pollutant exposure profiles most closely associated with scores on a standardized mathematics test administered to children in kindergarten. In the second-stage, the exposure profiles frequently predicting lower math scores were included within linear regression models and adjusted for confounders in order to estimate the magnitude of their effect on math scores. This approach was applied to the full population, and then to the populations living in urban and highly-populated urban areas. Our first-stage results in the full population suggested children with low trichloroethylene exposure had significantly lower math scores. This association was not observed for children living in urban communities, suggesting that confounding related to urbanicity needs to be considered within the first-stage. When restricting our analysis to populations living in urban and highly-populated urban areas, high isophorone levels were found to predict lower math scores. Within adjusted regression models of children in highly-populated urban areas, the estimated effect of higher isophorone exposure on math scores was -1.19 points (95% CI -1.94, -0.44). Similar results were observed for the overall population of urban children. This data-driven, two-stage approach can be applied to other populations, exposures and outcomes to generate hypotheses within high-dimensional exposure data. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Synthesis and Characterization of Mesoporous Silica Functionalized with Calix[4]arene Derivatives

PubMed Central

Alahmadi, Sana M.; Mohamad, Sharifah; Maah, Mohd Jamil

2012-01-01

This work reports a new method to covalently attach calix[4]arene derivatives onto MCM-41, using a diisocyanate as a linker. The modified mesoporous silicates were characterized by fourier transform infrared spectroscopy (FTIR), thermal analysis (TGA) and elemental analysis. The FTIR spectra and TGA analysis verified that the calix[4]arene derivates are covalently attached to the mesoporous silica. The preservation of the MCM-41 channel system was checked by X-ray diffraction and nitrogen adsorption analysis. PMID:23202977

Pervaporation separation of ethanol-water mixtures using polyethylenimine composite membranes

DOEpatents

Neidlinger, H.H.; Schissel, P.O.; Orth, R.A.

1987-04-21

Synthetic, organic, polymeric membranes were prepared from polyethylenimine for use with pervaporation apparatus in the separation of ethanol-water mixtures. The polymeric material was prepared in dilute aqueous solution and coated onto a polysulfone support film, from which excess polymeric material was subsequently removed. Cross-links were then generated by limited exposure to toluene-2,4-diisocyanate solution, after which the prepared membrane was heat-cured. The resulting membrane structures showed high selectivity in permeating ethanol or water over a wide range of feed concentrations.

Pervaporation separation of ethanol-water mixtures using polyethylenimine composite membranes

DOEpatents

Neidlinger, Hermann H.; Schissel, Paul O.; Orth, Richard A.

1987-01-01

Synthetic, organic, polymeric membranes were prepared from polyethylenimine for use with pervaporation apparatus in the separation of ethanol-water mixtures. The polymeric material was prepared in dilute aqueous solution and coated onto a polysulfone support film, from which excess polymeric material was subsequently removed. Cross-links were then generated by limited exposure to toluene-2,4-diisocyanate solution, after which the prepared membrane was heat-cured. The resulting membrane structures showed high selectivity in permeating ethanol or water over a wide range of feed concentrations.

The Israel DNA database--the establishment of a rapid, semi-automated analysis system.

PubMed

Zamir, Ashira; Dell'Ariccia-Carmon, Aviva; Zaken, Neomi; Oz, Carla

2012-03-01

The Israel Police DNA database, also known as IPDIS (Israel Police DNA Index System), has been operating since February 2007. During that time more than 135,000 reference samples have been uploaded and more than 2000 hits reported. We have developed an effective semi-automated system that includes two automated punchers, three liquid handler robots and four genetic analyzers. An inhouse LIMS program enables full tracking of every sample through the entire process of registration, pre-PCR handling, analysis of profiles, uploading to the database, hit reports and ultimately storage. The LIMS is also responsible for the future tracking of samples and their profiles to be expunged from the database according to the Israeli DNA legislation. The database is administered by an in-house developed software program, where reference and evidentiary profiles are uploaded, stored, searched and matched. The DNA database has proven to be an effective investigative tool which has gained the confidence of the Israeli public and on which the Israel National Police force has grown to rely. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Isocyanate Cross-Linked Silica: Structurally Strong Aerogels

NASA Technical Reports Server (NTRS)

Leventis, Nicholas; Sotiriou-Leventis, Chariklia; Zhang, Guo-Hui; Rawashdeh, Abdel-Monem M.

2002-01-01

Molecular-level synergism between the silica nanoparticles of pre-formed monoliths and molecular cross-linkers inverts the relative host-guest roles in glass-polymer composites, leading to new strong low-density materials. Attempts to load gels with variable amounts of polyurethane precursors such as di-ISO and diol end-capped polybutylene adipate followed by heat treatment, washing, and supercritical drying led to opaque materials, somewhat stronger than silica but still quite brittle and much inferior to the materials described above. Direct mixing of a diisocyanate and an alcohol-free sol has been attempted recently by Yim et al. Reportedly, that procedure leads to week-long gelation times and requires an at least equally long aging period. In our attempt to add various amounts of di-ISO in a base-catalyzed sol in PC, we also noticed a week-long gelation time. The resulting aerogels were translucent but no less brittle than native silica. According to more recent studies, if propylene carbonate is replaced with acetone, it leads not only to shorter processing times, but also to much stronger gels that can tolerate loads in excess of 40 kg in the arrangement presented. We attribute that behavior to the lower viscosity of acetone, that allows faster diffusion of the di-ISO solution within the pores before di-ISO has time to react with the surface of silica. Further studies are underway to vary the chemical identity of the diisocyanate, as well as the composition and density of silica.

Temperature- and pH-responsive nanoparticles of biocompatible polyurethanes for doxorubicin delivery.

PubMed

Wang, Anning; Gao, Hui; Sun, Yanfang; Sun, Yu-long; Yang, Ying-Wei; Wu, Guolin; Wang, Yinong; Fan, Yunge; Ma, Jianbiao

2013-01-30

A series of temperature- and pH-responsive polyurethanes based on hexamethylene diisocyanate (HDI) and 4,4'-diphenylmethane diisocyanate (MDI) were synthesized by a coupling reaction with bis-1,4-(hydroxyethyl) piperazine (HEP), N-methyldiethanolamine (MDEA) and N-butyldiethanolamine (BDEA), respectively. The chemical structure, molecular weight, thermal property and crystallization properties were characterized by Fourier transform infrared (FT-IR) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC) and X-ray diffraction (XRD) spectroscopy. The resulting polyurethanes were then used to prepare nanoparticles either by direct dispersion method or dialysis method. Their pH and temperature responsibilities were evaluated by optical transmittance and size measurement in aqueous media. Interestingly, HDI-based and MDI-based polyurethanes exhibited different pH and temperature responsive properties. Nanoparticles based on HDI-HEP and HDI-MDEA were temperature-responsive, while MDI-based biomaterials were not. All of them showed pH-sensitive behavior. The possible responsive mechanism was investigated by (1)H NMR spectroscopy. The cytotoxicity of the polyurethanes was evaluated using methylthiazoletetrazolium (MTT) assay in vitro. It was shown that the HDI-based polyurethanes were non-toxic, and could be applied to doxorubicin (DOX) encapsulation. The experimental results indicated that DOX could be efficiently encapsulated into polyurethane nanoparticles and uptaken by Huh-7 cells. The loaded DOX molecules could be released from the drug-loaded polyurethane nanoparticles upon pH and temperature changes, responsively. Copyright © 2012 Elsevier B.V. All rights reserved.

Biobased Epoxy Resins from Deconstructed Native Softwood Lignin.

PubMed

van de Pas, Daniel J; Torr, Kirk M

2017-08-14

The synthesis of novel epoxy resins from lignin hydrogenolysis products is reported. Native lignin in pine wood was depolymerized by mild hydrogenolysis to give an oil product that was reacted with epichlorohydrin to give epoxy prepolymers. These were blended with bisphenol A diglycidyl ether or glycerol diglycidyl ether and cured with diethylenetriamine or isophorone diamine. The key novelty of this work lies in using the inherent properties of the native lignin in preparing new biobased epoxy resins. The lignin-derived epoxy prepolymers could be used to replace 25-75% of the bisphenol A diglycidyl ether equivalent, leading to increases of up to 52% in the flexural modulus and up to 38% in the flexural strength. Improvements in the flexural strength were attributed to the oligomeric products present in the lignin hydrogenolysis oil. These results indicate lignin hydrogenolysis products have potential as sustainable biobased polyols in the synthesis of high performance epoxy resins.

Dynamic spiking studies using the DNPH sampling train

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steger, J.L.; Knoll, J.E.

1996-12-31

The proposed aldehyde and ketone sampling method using aqueous 2,4-dinitrophenylhydrazine (DNPH) was evaluated in the laboratory and in the field. The sampling trains studied were based on the train described in SW 846 Method 0011. Nine compounds were evaluated: formaldehyde, acetaldehyde, quinone, acrolein, propionaldeyde, methyl isobutyl ketone, methyl ethyl ketone, acetophenone, and isophorone. In the laboratory, the trains were spiked both statistically and dynamically. Laboratory studies also investigated potential interferences to the method. Based on their potential to hydrolyze in acid solution to form formaldehyde, dimethylolurea, saligenin, s-trioxane, hexamethylenetetramine, and paraformaldehyde were investigated. Ten runs were performed using quadruplicate samplingmore » trains. Two of the four trains were dynamically spiked with the nine aldehydes and ketones. The test results were evaluated using the EPA method 301 criteria for method precision (< + pr - 50% relative standard deviation) and bias (correction factor of 1.00 + or - 0.30).« less

Integrating open-source software applications to build molecular dynamics systems.

PubMed

Allen, Bruce M; Predecki, Paul K; Kumosa, Maciej

2014-04-05

Three open-source applications, NanoEngineer-1, packmol, and mis2lmp are integrated using an open-source file format to quickly create molecular dynamics (MD) cells for simulation. The three software applications collectively make up the open-source software (OSS) suite known as MD Studio (MDS). The software is validated through software engineering practices and is verified through simulation of the diglycidyl ether of bisphenol-a and isophorone diamine (DGEBA/IPD) system. Multiple simulations are run using the MDS software to create MD cells, and the data generated are used to calculate density, bulk modulus, and glass transition temperature of the DGEBA/IPD system. Simulation results compare well with published experimental and numerical results. The MDS software prototype confirms that OSS applications can be analyzed against real-world research requirements and integrated to create a new capability. Copyright © 2014 Wiley Periodicals, Inc.

Poly(dimethylsiloxane)-Polyurethane Elastomers: Synthesis and Properties of Segmented Copolymers and Related Zwitterionomers.

DTIC Science & Technology

1984-11-01

8217-niethylenediphenylene diisocyanate (MDI) which was chain extended with either 1,4-butanediol (BD) or N -me thyl diethanol ami ne . - g.. ( MDEA ). The MDEA -extended...and then vacuum distilled. Tetrahydrofuran %S 9 4 (Aldrich) was dehydrated over calcium hydride. N -methyldiethanolamne ( MDEA ) (Aldrich) at 97 percent...2CM 2- N -CM2CH OH or MOCH 2CM 2CM2CM2OH MDEA B -EL-MTPS-( -MDI-BD--K-DI-+- TI x or nI X Schem~e 1. Synthetic sche-me for polysiloxa-e-pclyurethane

Unidirectional fibers and polyurethane elastomer matrix based composites synthesis and properties. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Chakar, A.

1984-01-01

A study of the properties and manufacturing techniques for long-fiber reinforced elastomeric composites for flexible and damping structural materials is presented. Attention is given to the usage of polyurethane in the matrix to obtain plastic elastomeric matrices and vitreous transition temperatures which vary from -80 C to 10 C, as well as assure good fiber adhesion. Various polyurethane formulations synthesized from diisocyanate prepolymers are examined in terms of mechanical and thermal properties. The principal reinforcing fiber selected is a unidirectional glass cloth.

One-Pot Conversion of Epoxidized Soybean Oil (ESO) into Soy-Based Polyurethanes by MoCl₂O₂ Catalysis.

PubMed

Pantone, Vincenzo; Annese, Cosimo; Fusco, Caterina; Fini, Paola; Nacci, Angelo; Russo, Antonella; D'Accolti, Lucia

2017-02-21

An innovative and eco-friendly one-pot synthesis of bio-based polyurethanes is proposed via the epoxy-ring opening of epoxidized soybean oil (ESO) with methanol, followed by the reaction of methoxy bio-polyols intermediates with 2,6-tolyl-diisocyanate (TDI). Both synthetic steps, methanolysis and polyurethane linkage formation, are promoted by a unique catalyst, molybdenum(VI) dichloride dioxide (MoCl₂O₂), which makes this procedure an efficient, cost-effective, and environmentally safer method amenable to industrial scale-up.

Pervaporation separation of ethanol-water mixtures using polyethylenimine composite membranes

DOEpatents

Neidlinger, H.H.; Schissel, P.O.; Orth, R.A.

1985-06-19

Synthetic, organic, polymeric membranes were prepared from polyethylenimine for use with pervaporation apparatus in the separation of ethanol-water mixtures. The polymeric material was prepared in dilute aqueous solution and coated onto a polysulfone support film, from which excess polymeric material was subsequently removed. Cross-links were then generated by limited exposure to toluene-2,4-diisocyanate solution, after which the prepared membrane was heat-cured. The resulting membrane structures showed high selectivity in permeating ethanol or water over a wide range of feed concentrations. 2 tabs.

Airborne concentrations of methylene diphenyl diisocyanate (MDI) in North American wood mills during the manufacturing of oriented strand board (OSB).

PubMed

Karoly, William J; Flatley, John J; Stevenson, Ralph D; Bowers, John D

2004-12-01

Air monitoring data were collected from industrial hygiene surveys over an 8-year period in oriented strand board (OSB) mills. Personal samples were taken to evaluate potential employee exposures to MDI. Area samples were taken to determine the effectiveness of control measures used in the mills to prevent fugitive emissions of wood dust, MDI, and MDI-coated wood dust from the OSB manufacturing process. Personal sampling results (578 samples covering 11 different job categories) ranged from 0.0002-0.524 mg/m3, with a GM = 0.001 and GSD = 3.71. Area sampling results (1657 samples covering 14 stationary locations in the mills) ranged from 0.0002-2.5 mg/m3, with a GM = 0.004 and GSD = 5.52. The statistical range of the data suggests high variability. While exposures to MDI above the established limits (0.051 mg/m3, 8-hour time-weighted average, 0.2 mg/m3, ceiling) can and do occur when engineering controls are not maintained and/or proper work practices and personal protective equipment are not followed/used for certain high exposure potential tasks, the data indicate that over 97% of the personal and 92% of the area sampling results are less than 0.051 mg/m3. Wipe testing was performed to determine the presence of removable, unreacted diisocyanates (NCO functional groups)from various surfaces. Positive results were found in about 13% of the wipe tests on surfaces confined to the blender, forming line, and hopper deck process areas.

Isocyanate exposure and asthma in the UK vehicle repair industry.

PubMed

Stocks, S J; Jones, K; Piney, M; Agius, R M

2015-12-01

Organic diisocyanates are a common cause of occupational asthma, particularly in motor vehicle repair (MVR) workers. The UK Health & Safety Laboratory provides screening for urinary hexamethylenediamine (UHDA), a biomarker of exposure to 1,6-hexamethylene diisocyanate (HDI). The UK Surveillance of Work-related and Occupational Respiratory Disease scheme (SWORD) has collected reports of occupational asthma since 1996. To compare trends in HDI exposure with trends in the incidence of work-related asthma attributed to isocyanates or paint spraying in MVR workers reported to SWORD. Two-level regression models were used to estimate trends in UHDA levels and work-related asthma in MVR workers reported to SWORD. The direction and magnitude of the trends were compared descriptively. From 2006 to 2014, there was a significant decline in the number of urine samples with detectable levels of UHDA (odds ratio = 0.96; 95% confidence intervals 0.94-0.98) and minimal change in those over the guidance value (1.03; 1.00-1.06). Over the same period, there was a significant decline in all asthma cases attributed to isocyanates or paint spraying reported to SWORD (0.90; 0.86-0.94) and a non-significant decline among MVR workers (0.94; 0.86-1.02). The simultaneous decrease in HDI exposure and incident cases of asthma reported to SWORD is temporally consistent with a reduction in exposure to airborne isocyanate leading to a reduction in asthma. Although this is not direct evidence of a causal relationship between the two trends, it is suggestive. © The Author 2015. Published by Oxford University Press on behalf of the Society of Occupational Medicine.

Isocyanate exposure and asthma in the UK vehicle repair industry

PubMed Central

Jones, K.; Piney, M.; Agius, R. M.

2015-01-01

Background Organic diisocyanates are a common cause of occupational asthma, particularly in motor vehicle repair (MVR) workers. The UK Health & Safety Laboratory provides screening for urinary hexamethylenediamine (UHDA), a biomarker of exposure to 1,6-hexamethylene diisocyanate (HDI). The UK Surveillance of Work-related and Occupational Respiratory Disease scheme (SWORD) has collected reports of occupational asthma since 1996. Aims To compare trends in HDI exposure with trends in the incidence of work-related asthma attributed to isocyanates or paint spraying in MVR workers reported to SWORD. Methods Two-level regression models were used to estimate trends in UHDA levels and work-related asthma in MVR workers reported to SWORD. The direction and magnitude of the trends were compared descriptively. Results From 2006 to 2014, there was a significant decline in the number of urine samples with detectable levels of UHDA (odds ratio = 0.96; 95% confidence intervals 0.94–0.98) and minimal change in those over the guidance value (1.03; 1.00–1.06). Over the same period, there was a significant decline in all asthma cases attributed to isocyanates or paint spraying reported to SWORD (0.90; 0.86–0.94) and a non-significant decline among MVR workers (0.94; 0.86–1.02). Conclusions The simultaneous decrease in HDI exposure and incident cases of asthma reported to SWORD is temporally consistent with a reduction in exposure to airborne isocyanate leading to a reduction in asthma. Although this is not direct evidence of a causal relationship between the two trends, it is suggestive. PMID:26209793

Polymerization of hexamethylene diisocyanate in solution and a 260.23 m/z [M+H]+ ion in exposed human cells.

PubMed

Wisnewski, Adam V; Liu, Jian; Redlich, Carrie A; Nassar, Ala F

2018-02-15

Hexamethylene diisocyanate (HDI) is an important industrial chemical that can cause asthma, however pathogenic mechanisms remain unclear. Upon entry into the respiratory tract, HDI's N=C=O groups may undergo nucleophilic addition (conjugate) to host molecules (e.g. proteins), or instead react with water (hydrolyze), releasing CO 2 and leaving a primary amine in place of the original N=C=O. We hypothesized that (primary amine groups present on) hydrolyzed or partially hydrolyzed HDI may compete with proteins and water as a reaction target for HDI in solution, resulting in polymers that could be identified and characterized using LC-MS and LC-MS/MS. Analysis of the reaction products formed when HDI was mixed with a pH buffered, isotonic, protein containing solution identified multiple [M+H] + ions with m/z's and collision-induced dissociation (CID) fragmentation patterns consistent with those expected for dimers (259.25/285.23 m/z), and trimers (401.36/427.35 m/z) of partially hydrolyzed HDI (e.g. ureas/oligoureas). Human peripheral blood mononuclear cells (PBMCs) and monocyte-like U937, but not airway epithelial NCI-H292 cell lines cultured with these HDI ureas contained a novel 260.23 m/z [M+H] + ion. LC-MS/MS analysis of the 260.23 m/z [M+H] + ion suggest the formula C 13 H 29 N 3 O 2 and a structure containing partially hydrolyzed HDI, however definitive characterization will require further orthogonal analyses. Copyright © 2017 Elsevier Inc. All rights reserved.

Quantification and Statistical Modeling—Part I: Breathing-Zone Concentrations of Monomeric and Polymeric 1,6-Hexamethylene Diisocyanate

PubMed Central

Fent, Kenneth W.; Gaines, Linda G. Trelles; Thomasen, Jennifer M.; Flack, Sheila L.; Ding, Kai; Herring, Amy H.; Whittaker, Stephen G.; Nylander-French, Leena A.

2009-01-01

We conducted a repeated exposure-assessment survey for task-based breathing-zone concentrations (BZCs) of monomeric and polymeric 1,6-hexamethylene diisocyanate (HDI) during spray painting on 47 automotive spray painters from North Carolina and Washington State. We report here the use of linear mixed modeling to identify the primary determinants of the measured BZCs. Both one-stage (N = 98 paint tasks) and two-stage (N = 198 paint tasks) filter sampling was used to measure concentrations of HDI, uretidone, biuret, and isocyanurate. The geometric mean (GM) level of isocyanurate (1410 μg m−3) was higher than all other analytes (i.e. GM < 7.85 μg m−3). The mixed models were unique to each analyte and included factors such as analyte-specific paint concentration, airflow in the paint booth, and sampler type. The effect of sampler type was corroborated by side-by-side one- and two-stage personal air sampling (N = 16 paint tasks). According to paired t-tests, significantly higher concentrations of HDI (P = 0.0363) and isocyanurate (P = 0.0035) were measured using one-stage samplers. Marginal R2 statistics were calculated for each model; significant fixed effects were able to describe 25, 52, 54, and 20% of the variability in BZCs of HDI, uretidone, biuret, and isocyanurate, respectively. Mixed models developed in this study characterize the processes governing individual polyisocyanate BZCs. In addition, the mixed models identify ways to reduce polyisocyanate BZCs and, hence, protect painters from potential adverse health effects. PMID:19622637

Biomonitoring Hexamethylene diisocyanate (HDI) exposure based on serum levels of HDI-specific IgG.

PubMed

Wisnewski, Adam V; Stowe, Meredith H; Nerlinger, Abby; Opare-Addo, Paul; Decamp, David; Kleinsmith, Christopher R; Redlich, Carrie A

2012-10-01

Isocyanate chemicals essential for polyurethane production are widely used industrially, and are increasingly found in consumer products. Asthma and other adverse health effects of isocyanates are well-documented and exposure surveillance is crucial to disease prevention. Hexamethylene diisocyanate (HDI)-specific serum immunoglobulin G (IgG) was evaluated as an exposure biomarker among workers at a US Air Force Air Logistics Center, which includes a large aircraft maintenance facility. HDI-specific IgG (HDI-IgG) titers in serum samples (n = 74) were measured using an enzyme-linked immunosorbent assay based upon the biuret form of HDI conjugated to human albumin. Information on personal protective equipment (PPE), work location/tasks, smoking, asthma history, basic demographics, and HDI skin exposure was obtained through questionnaire. HDI-specific serum IgG levels were elevated in n = 17 (23%) of the workers studied. The prevalence and/or end-titer of the HDI-IgG was significantly (P < 0.05) associated with specific job titles, self-reported skin exposure, night-shift work, and respirator use, but not atopy, asthma, or other demographic information. The highest titers were localized to specific worksites (C-130 painting), while other worksites (generator painting) had no or few workers with detectable HDI-IgG. HDI-specific immune responses (IgG) provide a practical biomarker to aid in exposure surveillance and ongoing industrial hygiene efforts. The strategy may supplement current air sampling approaches, which do not assess exposures via skin, or variability in PPE use or effectiveness. The approach may also be applicable to evaluating isocyanate exposures in other settings, and may extend to other chemical allergens.

Exposures to 1,6-hexamethylene diisocyanate during polyurethane spray painting in the U.S. Air Force.

PubMed

Carlton, G N; England, E C

2000-09-01

1,6-Hexamethylene diisocyanate (HDI) exposures were measured during polyurethane enamel spray painting at four Air Force bases. Breathing zone samples were collected for HDI monomer and polyisocyanates (oligomers) using three sampling methods: NIOSH Method 5521, the Iso-Chek sampler, and the total aerosol mass method (TAMM). Exposures to HDI monomer are low when compared to current occupational exposure limits; the highest 8-hr time-weighted average (TWA) exposure found was 3.5 micrograms/m3, below the American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 34 micrograms/m3. HDI oligomer levels were higher; mean task exposures indicated by either the Iso-Chek sampler or TAMM are above the Oregon ceiling limit of 1 mg/m3. Eight-hour TWA exposures, however, were much lower, with only one exceeding the Oregon standard of 0.5 mg/m3. Poor worker practices commonly observed during this study included: standing in downwind positions so paint overspray passed through breathing zones; spraying toward other painters; and using excessive paint spray gun air cap pressures. Workers should stand in upwind orientation relative to the aircraft being painted, causing overspray to move away from the painter's breathing zone; adjust their position to prevent spraying other painters or limit paint application to one worker at a time; and use air cap pressure gauges prior to spraying to limit spray gun air cap pressures and reduce paint overspray generation rates. These improved techniques will result in reduced worker exposures to isocyanates.

Factors affecting variability in the urinary biomarker 1,6-hexamethylene diamine in workers exposed to 1,6-hexamethylene diisocyanate.

PubMed

Gaines, Linda G T; Fent, Kenneth W; Flack, Sheila L; Thomasen, Jennifer M; Whittaker, Stephen G; Nylander-French, Leena A

2011-01-01

Although urinary 1,6-hexamethylene diamine (HDA) is a useful biomarker of exposure to 1,6-hexamethylene diisocyanate (HDI), a large degree of unexplained intra- and inter-individual variability exists between estimated HDI exposure and urine HDA levels. We investigated the effect of individual and workplace factors on urine HDA levels using quantitative dermal and inhalation exposure data derived from a survey of automotive spray painters exposed to HDI. Painters' dermal and breathing-zone HDI-exposures were monitored over an entire workday for up to three separate workdays, spaced approximately one month apart. One urine sample was collected before the start of work with HDI-containing paints, and multiple samples were collected throughout the workday. Using mixed effects multiple linear regression modeling, coverall use resulted in significantly lower HDA levels (p = 0.12), and weekday contributed to significant variability in HDA levels (p = 0.056). We also investigated differences in urine HDA levels stratified by dichotomous and classification covariates using analysis of variance. Use of coveralls (p = 0.05), respirator type worn (p = 0.06), smoker status (p = 0.12), paint-booth type (p = 0.02), and more than one painter at the shop (p = 0.10) were all found to significantly affect urine HDA levels adjusted for creatinine concentration. Coverall use remained significant (p = 0.10), even after adjusting for respirator type. These results indicate that the variation in urine HDA level is mainly due to workplace factors and that appropriate dermal and inhalation protection is required to prevent HDI exposure.

Isocyanate emissions from pyrolysis of mattresses containing polyurethane foam.

PubMed

Garrido, María A; Gerecke, Andreas C; Heeb, Norbert; Font, Rafael; Conesa, Juan A

2017-02-01

This study examined the emissions of powerful asthmatic agents called isocyanates from small-scale pyrolysis experiments of two common foams employed in mattress production such as flexible polyurethane foam (FPUF) and viscoelastic memory foam (VMF). A nitrogen atmosphere and five different temperatures, 300, 350, 400, 450 and 850 °C, were selected to carry out the experiments in order to evaluate the worst possible conditions for thermal degradation. A similar trend for both materials was found. At lower temperatures, diisocyanates were the most important products whereas at 850 °C monoisocyanates, and mainly isocyanic acid released mainly from the thermal cracking of diisocyanates evolved directly from the polymer chains. The total yields of isocyanates were in the range of 1.43-11.95 mg/m 3 for FPUF at 300-850 °C and 0.05-6.13 mg/m 3 for VMF, 300-850 °C. This difference could be a consequence of the lower amount of isocyanates employed in the VMF production which was confirmed by the nitrogen content of the foams, 5.95% FPUF vs. 3.34% in VMF. Additionally, a qualitative search for so far unknown isocyanates was performed in samples from the pyrolysis of FPUF at 300, 400 and 850 °C. It was confirmed that six different aminoisocyanates at 300 °C were evolved, whereas at 400 and 850 °C only five of them were detected. The general trend observed was a decrease of the aminoisocyanate levels with increasing pyrolysis temperature. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparison of solvent/derivatization agent systems for determination of extractable toluene diisocyanate from flexible polyurethane foam.

PubMed

Vangronsveld, Erik; Berckmans, Steven; Spence, Mark

2013-06-01

Flexible polyurethane foam (FPF) is produced from the reaction of toluene diisocyanate (TDI) and polyols. Limited and conflicting results exist in the literature concerning the presence of unreacted TDI remaining in FPF as determined by various solvent extraction and analysis techniques. This study reports investigations into the effect of several solvent/derivatization agent combinations on extractable TDI results and suggests a preferred method. The suggested preferred method employs a syringe-based multiple extraction of foam samples with a toluene solution of 1-(2-methoxyphenyl)-piperazine. Extracts are analyzed by liquid chromatography using an ion trap mass spectrometry detection technique. Detection limits of the method are ~10ng TDI g(-1) foam (10 ppb, w/w) for each TDI isomer (i.e. 2,4-TDI and 2,6-TDI). The method was evaluated by a three-laboratory interlaboratory comparison using two representative foam samples. The total extractable TDI results found by the three labs for the two foams were in good agreement (relative standard deviation of the mean of 30-40%). The method has utility as a basis for comparing FPFs, but the interpretation of extractable TDI results using any solvent as the true value for 'free' or 'unreacted' TDI in the foam is problematic, as demonstrated by the difference in the extracted TDI results from the different extraction systems studied. Further, a consideration of polyurethane foam chemistry raises the possibility that extractable TDI may result from decomposition of parts of the foam structure (e.g. dimers, biurets, and allophanates) by the extraction system.

Improved lignin polyurethane properties with Lewis acid treatment.

PubMed

Chung, Hoyong; Washburn, Newell R

2012-06-27

Chemical modification strategies to improve the mechanical properties of lignin-based polyurethanes are presented. We hypothesized that treatment of lignin with Lewis acids would increase the concentration of hydroxyl groups available to react with diisocyanate monomers. Under the conditions used, hydrogen bromide-catalyzed modification resulted in a 28% increase in hydroxyl group content. Associated increases in hydrophilicity of solvent-cast thin films were also recorded as evidenced by decreases in water contact angle. Polyurethanes were then prepared by first preparing a prepolymer based on mixtures of toluene-2,4-diisocyanate (TDI) and unmodified or modified lignin, then polymerization was completed through addition of polyethylene glycol (PEG), resulting in mass ratios of TDI:lignin:PEG of 43:17:40 in the compositions investigated here. The mixture of TDI and unmodified lignin resulted in a lignin powder at the bottom of the liquid, suggesting it did not react directly with TDI. However, a homogeneous solution resulted when TDI and the hydrogen bromide-treated lignin were mixed, suggesting demethylation indeed increased reactivity and resulted in better integration of lignin into the urethane network. Significant improvements in mechanical properties of modified lignin polyurethanes were observed, with a 6.5-fold increase in modulus, which were attributed to better integration of the modified lignin into the covalent polymer network due to the higher concentration of hydroxyl groups. This research indicates that chemical modification strategies can lead to significant improvements in the properties of lignin-based polymeric materials using a higher fraction of an inexpensive lignin monomer from renewable resources and a lower fraction an expensive, petroleum-derived isocyanate monomer to achieve the required material properties.

Role of substance P and neurokinin A in toluene diisocyanate-induced increased airway responsiveness in rabbits.

PubMed

Marek, W; Potthast, J J; Marcynski, B; Baur, X

1996-01-01

The aim of the present study was to examine the role of neuropeptides, especially substance P (SP) and neurokinin A (NKA), in toluene diisocyanate (TDI)-induced airway hyperresponsiveness (AHR) to acetylcholine aerosols. Thirty parts per billion of TDI in air administered over 4 hours caused a significant increase in the airway constrictive response to acetylcholine (ACH) aerosols in rabbits (DeltaRI: 245 +/- 30%, p < 0.005) without altering basic values of respiratory, cardiovascular or blood gas parameters. Inhalation of the aerosolized neuropeptides SP and NKA resulted in a similar increase in airway responsiveness (AR) to ACH as exposure to 30 ppb TDI. To determine whether neuropeptides contribute to TDI-induced AHR, we studied their effects after systemic treatment with capsaicin as well as after infusion of specific synthetic antagonists for SP and NK2 (NKA) receptors. CAPS treatment performed on 4 consecutive days as well as antagonists' infusion only moderately (p > 0.05) decreased airway responses to ACH. CAPS application prevented the TDI-induced increase in AR to ACH in all rabbits. The increase in airway resistance to ACH did not significantly change after TDI exposure (98 +/- 22% of the control response before TDI, p > 0.05). Simultaneous infusion of specific synthetic SP and NK2 receptor antagonists also abolished the TDI-induced increase in airway responses to ACH in all animals investigated (p > 0.05). The results of this study demonstrate that neuropeptides, especially the tachykinins SP and NKA, are important mediators in TDI-induced AHR in rabbits.

Evaluation of DNA damage and cytotoxicity of polyurethane-based nano- and microparticles as promising biomaterials for drug delivery systems

NASA Astrophysics Data System (ADS)

Caon, Thiago; Zanetti-Ramos, Betina Giehl; Lemos-Senna, Elenara; Cloutet, Eric; Cramail, Henri; Borsali, Redouane; Soldi, Valdir; Simões, Cláudia Maria Oliveira

2010-06-01

The in vitro cytotoxicity and DNA damage evaluation of biodegradable polyurethane-based micro- and nanoparticles were carried out on animal fibroblasts. For cytotoxicity measurement and primary DNA damage evaluation, MTT and Comet assays were used, respectively. Different formulations were tested to evaluate the influence of chemical composition and physicochemical characteristics of particles on cell toxicity. No inhibition of cells growth surrounding the polyurethane particles was observed. On the other hand, a decrease of cell viability was verified when the anionic surfactant sodium dodecyl sulfate (SDS) was used as droplets stabilizer of monomeric phase. Polyurethane nanoparticles stabilized with Tween 80 and Pluronic F68 caused minor cytotoxic effects. These results indicated that the surface charge plays an important role on cytotoxicity. Particles synthesized from MDI displayed a higher cytotoxicity than those synthesized from IPDI. Size and physicochemical properties of the particles may explain the higher degree of DNA damage produced by two tested formulations. In this way, a rational choice of particles' constituents based on their cytotoxicity and genotoxicity could be very useful for conceiving biomaterials to be used as drug delivering systems.

Synthesis and Characterization of High Energy Sheet Materials Based on HMX / RDX and Hydroxyl Terminated Polybutadiene

NASA Astrophysics Data System (ADS)

Elsharkawy, Karim; Guo, Lin; Taha, Elhussein; Fouda, Hany

2017-07-01

In this paper three types of thin sheets of highly energetic materials were prepared and characterized. The first based on 1,3,5,7-tetranitro-1,3,5,7-tetrazocane (HMX). The second type based on 1,3,5-trinitro-1,3,5-triazinane (RDX). Both types contain polyurethane (PU), formulated by hydroxyl terminated polybutadiene (HTPB) and Isophorondiisocyanate (IPDI). The third type based on (RDX) and polyisoprene (PI) as high elastomeric material. The first and second types of thin sheets were prepared by applying the casting technique while the third type was prepared by slurry technique then followed by rolling of the prepared beads of the RDX coated by PI. These high energy sheet materials were cured in oven at 60°C. The measured explosive properties of the prepared sheets were discussed and showed that the sensitivity to impact and friction of the prepared sheets explosives materials were markedly decreased when compared to pure HMX or pure RDX, but the sensitivity to heat was close to that of pure RDX. In spite of the markedly decrease in the sensitivity of these sheets, the explosive characteristics were nearly not affected the sheets have very good stress-strain values.

Curable liquid hydrocarbon prepolymers containing hydroxyl groups and process for producing same

NASA Technical Reports Server (NTRS)

Rhein, R. A.; Ingham, J. D. (Inventor)

1978-01-01

Production of hydroxyl containing curable liquid hydrocarbon prepolymers by ozonizing a high molecular weight saturated hydrocarbon polymer such as polyisobutylene or ethylene propylene rubber is discussed. The ozonized material is reduced using reducing agents, preferably diisobutyl aluminum hydride, to form the hydroxyl containing liquid prepolymers having a substantially lower molecular weight than the parent polymer. The resulting curable liquid hydroxyl containing prepolymers can be poured into a mold and readily cured, with reactants such as toluene diisocyanate, to produce highly stable elastomers having a variety of uses such as binders for solid propellants.

Poly(iohexol) nanoparticles as contrast agents for in vivo X-ray computed tomography imaging.

PubMed

Yin, Qian; Yap, Felix Y; Yin, Lichen; Ma, Liang; Zhou, Qin; Dobrucki, Lawrence W; Fan, Timothy M; Gaba, Ron C; Cheng, Jianjun

2013-09-18

Biocompatible poly(iohexol) nanoparticles, prepared through cross-linking of iohexol and hexamethylene diisocyanate followed by coprecipitation of the resulting cross-linked polymer with mPEG-polylactide, were utilized as contrast agents for in vivo X-ray computed tomography (CT) imaging. Compared to conventional small-molecule contrast agents, poly(iohexol) nanoparticles exhibited substantially protracted retention within the tumor bed and a 36-fold increase in CT contrast 4 h post injection, which makes it possible to acquire CT images with improved diagnosis accuracy over a broad time frame without multiple administrations.

Studies on polyurethane adhesives and surface modification of hydrophobic substrates

NASA Astrophysics Data System (ADS)

Krishnamoorthy, Jayaraman

This thesis work deals with (a) Curing of reactive, hot-melt polyurethane adhesives and (b) Adsorption studies using different interactions. Research on polyurethanes involves characterization of polyurethane prepolymers and a novel mechanism to cure isocyanate-terminated polyurethane prepolymer by a "trigger" mechanism. Curing of isocyanate-terminated polyurethane prepolymers has been shown to be influenced by morphology and environmental conditions such as temperature and relative humidity. Although the initial composition, final morphology and curing kinetics are known, information regarding the intermediate prepolymer mixture is yet to be established. Polyurethane prepolymers prepared by the reaction of diisocyanates with the primary hydroxyls of polyester diol (PHMA) and secondary hydroxyls of polyether diol (PPG) were characterized. The morphology and crystallization kinetics of a polyurethane prepolymer was compared with a blend of PPG prepolymer (the product obtained by the reaction of PPG with diisocyanate) and a PHMA prepolymer (the product obtained by the reaction of PHMA with diisocyanate) to study the effect of copolymer formed in the polyurethane prepolymer on the above-mentioned properties. Although the morphology of the polyurethane prepolymer is determined in the first few minutes of application, the chemical curing of isocyanate-terminated prepolymer occurs over hours to days. In the literature, different techniques are described to follow the curing kinetics. But there is no established technique to control the curing of polyurethane prepolymer. To make the curing process independent of environmental factors, a novel approach using a trigger mechanism was designed and implemented by using ammonium salts as curing agents. Ammonium salts that are stable at room temperature but decompose on heating to yield active hydrogen-containing compounds, NH3 and H2O, were used as 'Trojan horses' to cure the prepolymer chemically. Research on adsorption studies involved making functionalized, thickness-controlled, wettability-controlled multilayers on hydrophobic substrates and the adsorption of carboxylic acid-terminated poly(styrene-b-isoprene) on alumina/silica substrates. Poly(vinyl alcohol) has been shown to adsorb onto hydrophobic surfaces irreversibly due to hydrophobic interactions. This thin semicrystalline coating is chemically modified using acid chlorides, butyl isocyanate and butanal to form thicker and hydrophobic coatings. The products of the modification reactions allow adsorption of a subsequent layer of poly(vinyl alcohol) that could subsequently be hydrophobized. This 2-step (adsorption/chemical modification) allows layer-by-layer deposition to prepare coatings with thickness, chemical structure and wettability control on any hydrophobic surface. Research on adsorption characteristics of carboxylic acid-terminated poly(styrene-b-isoprene) involved syntheses of block copolymers with the functional group present at specific ends. Comparative adsorption studies for carboxylic acid-terminated and hydrogen-terminated block copolymers was carried out on alumina and silica substrates.

Exposure to 4,4'-methylenediphenyl diisocyanate (MDI) during moulding of rigid polyurethane foam: determination of airborne MDI and urinary 4,4'-methylenedianiline (MDA).

PubMed

Kääriä, K; Hirvonen, A; Norppa, H; Piirilä, P; Vainio, H; Rosenberg, C

2001-04-01

Occupational exposure to 4,4'-methylenediphenyl diisocyanate (MDI) was measured during moulding of rigid polyurethane foam. The aim of the study was to find out whether an MDI-derived urinary amine metabolite could be detected in the urine of workers exposed to apparently low levels of MDI. Airborne MDI was sampled on 1-(2-methoxyphenyl)-piperazine (2MP)-impregnated glass fibre filters and determined by high-performance liquid chromatography (HPLC) using ultraviolet (UV) and electrochemical (EC) detection. The limit of detection of MDI was 3 ng ml-1 for a 20 microliters injection. The precision of sample preparation, expressed as relative standard deviation (RSD), was 1.3% with UV detection and 2.1% with EC detection at a concentration of 70 ng MDI ml-1 (n = 6). The 2MP-MDI derivative was stable at +4 degrees C up to eight weeks. The accuracy of the method was validated in an international quality control programme. Workers (n = 57) from three different factories participated in the study. Urinary 4,4'-methylenedianiline (MDA) metabolite was determined after acid hydrolysis as heptafluorobutyric anhydride derivatives by gas chromatography-mass spectrometry using chemical ionisation and monitoring negative ions. The limit of detection in urine was 0.2 nmol l-1. The precision of six analyses for a urine sample spiked to a concentration of 1 nmol l-1 was 29% (RSD). The MDI concentrations were below the limit of detection in most (64%) of the air samples collected in the worker's breathing zone. Still, detectable amounts of MDA were found in 97% of the urine samples. Monitoring of urinary MDA appears to be an appropriate method of assessing MDI exposure in work environments with low or undetectable MDI concentrations in the workplace air.

Effect of toluene diisocyanate on homeostasis of intracellular-free calcium in human neuroblastoma SH-SY5Y Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, P.-S.; Chiung, Y.-M.; Department of Microbiology and Immunology, National Defense Medical Center, Taipei, Taiwan

2006-03-01

The mechanisms of TDI (2,4-toluene diisocyanate)-induced occupational asthma are not fully established. Previous studies have indicated that TDI induces non-specific bronchial hyperreactivity to methacholine and induces contraction of smooth muscle tissue by activating 'capsaicin-sensitive' nerves resulting asthma. Cytosolic-free calcium ion concentrations ([Ca{sup 2+}]{sub c}) are elevated when either capsaicin acts at vanilloid receptors, or methacholine at muscarinic receptors. This study therefore investigated the effects of TDI on Ca{sup 2+} mobilization in human neuroblastoma SH-SY5Y cells. TDI was found to elevate [Ca{sup 2+}]{sub c} by releasing Ca{sup 2+} from the intracellular stores and extracellular Ca{sup 2+} influx. 500 {mu}M TDI inducedmore » a net [Ca{sup 2+}]{sub c} increase of 112 {+-} 8 and 78 {+-} 6 nM in the presence and absence of extracellular Ca{sup 2+}, respectively. In Ca{sup 2+}-free buffer, TDI induced Ca{sup 2+} release from internal stores to reduce their Ca{sup 2+} content and this reduction was evidenced by a suppression occurring on the [Ca{sup 2+}]{sub c} rise induced by thapsigargin, ionomycin, and methacholine after TDI incubation. In the presence of extracellular Ca{sup 2+}, simultaneous exposure to TDI and methacholine led a higher level of [Ca{sup 2+}]{sub c} compared to single methacholine stimulation, that might explain that TDI induces bronchial hyperreactivity to methacholine. We conclude that TDI is capable of interfering the [Ca{sup 2+}]{sub c} homeostasis including releasing Ca{sup 2+} from internal stores and inducing extracellular Ca{sup 2+} influx. The interaction of this novel character and bronchial hyperreactivity need further investigation.« less

Determination of technical grade isocyanates used in the production of polyurethane plastics.

PubMed

Marand, Asa; Dahlin, Jakob; Karlsson, Daniel; Skarping, Gunnar; Dalene, Marianne

2004-07-01

A method for determination of technical grade isocyanates used in the production of polyurethane (PUR) is presented. The isocyanates in technical grade products were characterised as di-n-butylamine (DBA) derivatives using LC-MS and LC-chemiluminescent nitrogen detection (CLND) and the total isocyanate content was compared to a titration assay. For collection of isocyanates in air, an impinger-filter sampling technique with DBA as derivatisation reagent was used. Characterised DBA and nonadeuterium labelled DBA derivatives of isocyanates in technical products were used as calibration standards and internal standards, respectively, in the analysis of air samples. Three workplaces were studied where PUR products were produced either by spraying or by moulding. In both technical products and in air samples, a number of monomeric, oligomeric and prepolymeric isocyanates of e.g. methylenebisphenyl diisocyanate (MDI) and hexamethylene diisocyanate (HDI) were characterised. Several of these have not previously been described in workplace atmospheres. In the technical isocyanate products, between 69 and 102% of the NCO content determined by titration was accounted for by LC-CLND. Quantifications of a wide range of isocyanates in air samples were performed with correlation coefficients in the range 0.988-0.999 (n= 8) and the instrumental detection limits were 0.7-25 pg. At the two workplaces where MDI- and HDI isocyanurate-based products were sprayed, the isocyanate composition in the air reflected the composition in the technical product. At the workplace where a MDI-based product was used in a moulding process, only the monomeric isocyanates were found in the air. The advantage of using characterised technical grade isocyanates as analytical standards was clearly demonstrated and the possibility of using index compounds when monitoring isocyanate exposure is discussed.

Biomonitoring Hexamethylene Diisocyanate (HDI) Exposure Based on Serum Levels of HDI-Specific IgG

PubMed Central

Wisnewski, Adam V.; Stowe, Meredith H.; Nerlinger, Abby; Opare-addo, Paul; Decamp, David; Kleinsmith, Christopher R.; Redlich, Carrie A.

2012-01-01

Objectives: Isocyanate chemicals essential for polyurethane production are widely used industrially, and are increasingly found in consumer products. Asthma and other adverse health effects of isocyanates are well-documented and exposure surveillance is crucial to disease prevention. Hexamethylene diisocyanate (HDI)-specific serum immunoglobulin G (IgG) was evaluated as an exposure biomarker among workers at a US Air Force Air Logistics Center, which includes a large aircraft maintenance facility. Methods: HDI-specific IgG (HDI-IgG) titers in serum samples (n = 74) were measured using an enzyme-linked immunosorbent assay based upon the biuret form of HDI conjugated to human albumin. Information on personal protective equipment (PPE), work location/tasks, smoking, asthma history, basic demographics, and HDI skin exposure was obtained through questionnaire. Results: HDI-specific serum IgG levels were elevated in n = 17 (23%) of the workers studied. The prevalence and/or end-titer of the HDI-IgG was significantly (P < 0.05) associated with specific job titles, self-reported skin exposure, night-shift work, and respirator use, but not atopy, asthma, or other demographic information. The highest titers were localized to specific worksites (C-130 painting), while other worksites (generator painting) had no or few workers with detectable HDI-IgG. Conclusions: HDI-specific immune responses (IgG) provide a practical biomarker to aid in exposure surveillance and ongoing industrial hygiene efforts. The strategy may supplement current air sampling approaches, which do not assess exposures via skin, or variability in PPE use or effectiveness. The approach may also be applicable to evaluating isocyanate exposures in other settings, and may extend to other chemical allergens. PMID:22449630

Urine 1,6-Hexamethylene Diamine (HDA) Levels Among Workers Exposed to 1,6-Hexamethylene Diisocyanate (HDI)

PubMed Central

Gaines, Linda G. T.; Fent, Kenneth W.; Flack, Sheila L.; Thomasen, Jennifer M.; Ball, Louise M.; Richardson, David B.; Ding, Kai; Whittaker, Stephen G.; Nylander-french, Leena A.

2010-01-01

Urinary 1,6-hexamethylene diamine (HDA) may serve as a biomarker for systemic exposure to 1,6-hexamethylene diisocyanate (HDI) in occupationally exposed populations. However, the quantitative relationships between dermal and inhalation exposure to HDI and urine HDA levels have not been established. We measured acid-hydrolyzed urine HDA levels along with dermal and breathing-zone levels of HDI in 48 automotive spray painters. These measurements were conducted over the course of an entire workday for up to three separate workdays that were spaced approximately 1 month apart. One urine sample was collected before the start of work with HDI-containing paints and subsequent samples were collected during the workday. HDA levels varied throughout the day and ranged from nondetectable to 65.9 μg l−1 with a geometric mean and geometric standard deviation of 0.10 μg l−1 ± 6.68. Dermal exposure and inhalation exposure levels, adjusted for the type of respirator worn, were both significant predictors of urine HDA levels in the linear mixed models. Creatinine was a significant covariate when used as an independent variable along with dermal and respirator-adjusted inhalation exposure. Consequently, exposure assessment models must account for the water content of a urine sample. These findings indicate that HDA exhibits a biphasic elimination pattern, with a half-life of 2.9 h for the fast elimination phase. Our results also indicate that urine HDA level is significantly associated with systemic HDI exposure through both the skin and the lungs. We conclude that urinary HDA may be used as a biomarker of exposure to HDI, but biological monitoring should be tailored to reliably capture the intermittent exposure pattern typical in this industry. PMID:20530123

Urine 1,6-hexamethylene diamine (HDA) levels among workers exposed to 1,6-hexamethylene diisocyanate (HDI).

PubMed

Gaines, Linda G T; Fent, Kenneth W; Flack, Sheila L; Thomasen, Jennifer M; Ball, Louise M; Richardson, David B; Ding, Kai; Whittaker, Stephen G; Nylander-French, Leena A

2010-08-01

Urinary 1,6-hexamethylene diamine (HDA) may serve as a biomarker for systemic exposure to 1,6-hexamethylene diisocyanate (HDI) in occupationally exposed populations. However, the quantitative relationships between dermal and inhalation exposure to HDI and urine HDA levels have not been established. We measured acid-hydrolyzed urine HDA levels along with dermal and breathing-zone levels of HDI in 48 automotive spray painters. These measurements were conducted over the course of an entire workday for up to three separate workdays that were spaced approximately 1 month apart. One urine sample was collected before the start of work with HDI-containing paints and subsequent samples were collected during the workday. HDA levels varied throughout the day and ranged from nondetectable to 65.9 microg l(-1) with a geometric mean and geometric standard deviation of 0.10 microg l(-1) +/- 6.68. Dermal exposure and inhalation exposure levels, adjusted for the type of respirator worn, were both significant predictors of urine HDA levels in the linear mixed models. Creatinine was a significant covariate when used as an independent variable along with dermal and respirator-adjusted inhalation exposure. Consequently, exposure assessment models must account for the water content of a urine sample. These findings indicate that HDA exhibits a biphasic elimination pattern, with a half-life of 2.9 h for the fast elimination phase. Our results also indicate that urine HDA level is significantly associated with systemic HDI exposure through both the skin and the lungs. We conclude that urinary HDA may be used as a biomarker of exposure to HDI, but biological monitoring should be tailored to reliably capture the intermittent exposure pattern typical in this industry.

Quantitative plasma biomarker analysis in HDI exposure assessment.

PubMed

Flack, Sheila L; Fent, Kenneth W; Trelles Gaines, Linda G; Thomasen, Jennifer M; Whittaker, Steve; Ball, Louise M; Nylander-French, Leena A

2010-01-01

Quantification of amines in biological samples is important for evaluating occupational exposure to diisocyanates. In this study, we describe the quantification of 1,6-hexamethylene diamine (HDA) levels in hydrolyzed plasma of 46 spray painters applying 1,6-hexamethylene diisocyanate (HDI)-containing paint in vehicle repair shops collected during repeated visits to their workplace and their relationship with dermal and inhalation exposure to HDI monomer. HDA was detected in 76% of plasma samples, as heptafluorobutyryl derivatives, and the range of HDA concentrations was < or =0.02-0.92 microg l(-1). After log-transformation of the data, the correlation between plasma HDA levels and HDI inhalation exposure measured on the same workday was low (N = 108, r = 0.22, P = 0.026) compared with the correlation between plasma HDA levels and inhalation exposure occurring approximately 20 to 60 days before blood collection (N = 29, r = 0.57, P = 0.0014). The correlation between plasma HDA levels and HDI dermal exposure measured on the same workday, although statistically significant, was low (N = 108, r = 0.22, P = 0.040) while the correlation between HDA and dermal exposure occurring approximately 20 to 60 days before blood collection was slightly improved (N = 29, r = 0.36, P = 0.053). We evaluated various workplace factors and controls (i.e. location, personal protective equipment use and paint booth type) as modifiers of plasma HDA levels. Workers using a downdraft-ventilated booth had significantly lower plasma HDA levels relative to semi-downdraft and crossdraft booth types (P = 0.0108); this trend was comparable to HDI inhalation and dermal exposure levels stratified by booth type. These findings indicate that HDA concentration in hydrolyzed plasma may be used as a biomarker of cumulative inhalation and dermal exposure to HDI and for investigating the effectiveness of exposure controls in the workplace.

Toluene diisocyanate caused electrophysiological disturbances in the upper airways wall.

PubMed

Piskorska, Elzbieta; Hołyńska-Iwan, Iga; Kaczorowski, Piotr; Soczywko-Ciudzińska, Julita; Wiciński, Michał; Lampka, Magdalena; Smuszkiewicz, Piotr; Tyrakowski, Tomasz

2009-01-01

Toluene diisocyanate (TDI) due to its widespread use in industry is one of the most common and well-known causes of occupational asthma and Reactive Airways Dysfunction Syndrome (RADS). In this study the impact of TDI on the electrophysiological properties of the airways wall, particularly on the mechanisms of absorption of sodium ions and chloride ions secretion was evaluated. Isolated rabbit tracheal wall (from outbred stock animals) was mounted in an apparatus for electrophysiological experiments by means of Ussing method and was mechanically stimulated by the jet flux of specified fluid directed onto the mucosal surface of the tissue from a peristaltic pump. The measured parameters were: transepithelial potential difference under control conditions (PD, mV), after mechanical stimulation (dPD or physiological reaction of hyperpolarization, mV) and electric resistance (R, Omega cm2). When TDI (0.035 mM) was added to stimulation fluid, only the immediate reaction was identified and when it was added to incubation fluid and other experimental fluids, the late (post-incubation) reaction was determined. The experiments involving the inhibition of Na+ by amiloride and Cl- by bumetanide were also performed. A series of functional tests for 72 pieces of tracheal wall from 36 animals were performed. It has been shown that short-term exposure to TDI significantly changed the course of reactions to mechanical stimulation. Also after incubation in the presence of TDI, the reactions to mechanical stimulation were changed in relation to control conditions. The immediate reaction of the isolated rabbit tracheal wall after exposure to TDI depends on the duration of exposure and on the physiological condition of the tissue in respect of sodium and chloride ion transport.

Respiratory response to toluene diisocyanate depends on prior frequency and concentration of dermal sensitization in mice.

PubMed

Vanoirbeek, Jeroen A J; Tarkowski, Maciej; Ceuppens, Jan L; Verbeken, Erik K; Nemery, Benoit; Hoet, Peter H M

2004-08-01

Occupational asthma is the principal cause of work-related respiratory disease in the industrial world. In the absence of satisfactory models for predicting the potential of low molecular weight chemicals to cause asthma, we verified that dermal sensitization prior to intranasal challenge influences the respiratory response using toluene diisocyanate (TDI), a known respiratory sensitizer. BALB/c mice received TDI or vehicle (acetone/olive oil) on each ear on three consecutive days (days 1, 2, and 3; 0.3 or 3% TDI) or only once (day 1, 1% TDI). On day 7, the mice received similar dermal applications of vehicle or the same concentration of TDI as before ("boost"). On day 10, they received an intranasal dose of TDI (0.1%) or vehicle. Ventilatory function was monitored by whole body plethysmography for 40 min after intranasal application, and reactivity to inhaled methacholine was assessed 24 h later. Pulmonary inflammation was assessed by bronchoalveolar lavage and histology. Mice that received an intranasal dose of TDI without having received a prior dermal application of TDI did not exhibit any ventilatory response or inflammatory changes compared to vehicle controls. In contrast, mice that had received prior application(s) of TDI, even if only on day 7, exhibited the following: ventilatory responses, compatible with bronchoconstriction, immediately after intranasal application with TDI; enhanced methacholine responsiveness 24 h later; and pulmonary inflammation characterized by neutrophils. This was, however, not the case in mice that received the highest dermal amount of TDI (3% on days 1, 2, and 3). These findings suggest that respiratory response to TDI depends on prior frequency and concentration of dermal sensitization in mice.

NLOphoric multichromophoric auxiliary methoxy aided triphenylamine D-π-A chromophores - Spectroscopic and computational studies

NASA Astrophysics Data System (ADS)

Erande, Yogesh; Kothavale, Shantaram; Sreenath, Mavila C.; Chitrambalam, Subramaniyan; Joe, Isaac H.; Sekar, Nagaiyan

2017-11-01

Molecules containing methoxy supported triphenylamine as strong electron-donor and dicyanovinyl as electron-acceptor groups interacting via isophorone as a configurationally locked polyene π-conjugated bridge are studied for their nonlinear optical properties. The photophysical study of examined chromophores in non-polar and polar solvents suggest that they exhibit strong emission solvatochromism and significant charge transfer characteristics supported by Lippert-Mataga plots and Generalised Mulliken Hush analysis. Linear and nonlinear optical properties as well as electronic properties measured by spectroscopic methods and cyclic voltametry and supported by DFT calculation were used to elucidate the structure property relationships. All three chromophores exhibit very high thermal stabilities with the decomposition temperatures higher than 340°C. The vibrational motions play very important role in determining the overall NLO response styryl chromophores which was established by DFT study. Dye 3 with maximum nonlinear optical susceptibility among three D-π-A systems proves that the multibranched push-pull chromophores exhibit a higher third order nonlinear susceptibility and justifies the design strategy.

Synthesis of polymer networks containing degradable polyacetal segments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goethals, E.J.; Trossaert, G.G.; Hartmann, P.J.

1993-12-31

In recent years, intensive research has been done in order to prepare different types of degradable polyacetal containing networks. In the present presentation four different routes for the production of polyacetal containing networks are described: (1) free radical copolymerization of {alpha},{omega}-(meth)acrylate terminated polyacetals (2) hydrosilylation reactions of {alpha},{omega}-allyl terminated poly-(1,3-dioxolane) with a multifunctional silane (3) modification of {alpha}{omega}-hydroxy terminated poly-(1,3-dioxepane) through reaction with 3-isocyanato propyl triethoxysilane and subsequent cross-linking under influence of H{sub 2}O and (4) synthesis of multifunctional hydroxy-terminated polyacetals, followed by cross-linking with di-isocyanates.

Preparation, testing, and delivery of low density polyimide foam panels

NASA Technical Reports Server (NTRS)

Ball, G. L., III; Post, L. K.; Salyer, I. O.

1975-01-01

Plastic foams based on polyimide resins were shown to be stable at relatively high temperatures, and to possess very low flame spread and smoke generation characteristics. A system and process were developed to prepare low-density polyimide foam from a liquid formulation. The system is based on the reaction of micropulverized grade pyromellitic dianhydride with a polymeric diisocyanate. The panels produced were postcured at elevated temperatures to achieve maximum thermal and fire resistance, and incorporation of a fire retardant into the formulation was considered. The effects of a flame retardant (Flameout 5600B1) were investigated, but eliminated in preference to the postcuring approach.

Nanostructure and Dynamics of Ionic and Non-Ionic PEO-Containing Polyureas

NASA Astrophysics Data System (ADS)

Chuayprakong, Sunanta; Runt, James

2013-03-01

A series of polyethylene oxide (PEO) - based diamines with molecular weights ranging from 250 - 6000 g/mol were polymerized in solution with 4,4'-methylene diphenyl diisocyanate (MDI). In addition, PEO soft segment diamines where modified to incorporate ionomeric species and also polymerized with MDI. The role of PEO soft segment molecular weight and the presence of ionic species on nanoscale segregation and cation conductivity were explored. The former was investigated using small-angle X-ray scattering and atomic force microscopy. Dielectric relaxation spectroscopy was used to investigate polymer and ion dynamics. Local environment and hydrogen bonding were identified by using FTIR spectroscopy.

Second harmonic generation and photochromic grating in polyurethane films containing diazo isoxazole chromophore

NASA Astrophysics Data System (ADS)

Marański, Krzysztof; Kucharski, Stanisław; Ortyl, Ewelina; Nunzi, Jean-Michel; Ahmadi-Kandjani, Sohrab; Dabos-Seignon, Sylvie; Chan, Siu-Wai; Barille, Regis

2008-08-01

The chromophoric intermediate: 2,2'-({4-[( E)-(5-methylisoxazol-3-yl)diazenyl]phenyl}-imino)diethanol was used in polyaddition reaction with di-isocyanate to obtain a new polyurethane polymeric material showing nonlinear optical and photochromic properties. The maximum absorption band of the polymer film was at 418 nm. The illumination of the film with crossed beams of the 488 nm Ar + laser yielded surface relief grating of regular structure. Measurement of the frequency doubling signal with 1064 nm laser indicated the polymer as interesting material for photooptical applications. The measured nonlinear optical coefficient, d33, reached 90.2 pm/V.

Toluene diisocyanate emission to air and migration to a surface from a flexible polyurethane foam.

PubMed

Vangronsveld, Erik; Berckmans, Steven; Spence, Mark

2013-06-01

Flexible polyurethane foam (FPF) is produced from the reaction of toluene diisocyanate (TDI) and polyols. Because of the potential for respiratory sensitization following exposure to TDI, concerns have been raised about potential consumer exposure to TDI from residual 'free TDI' in FPF products. Limited and conflicting results exist in the literature concerning the presence of unreacted TDI remaining in FPF as determined by various solvent extraction and analysis techniques. Because residual TDI results are most often intended for application in assessment of potential human exposure to TDI from FPF products, testing techniques that more accurately simulated human contact with foam were designed. To represent inhalation exposure to TDI from polyurethane foam, a test that measured the emission of TDI to air was conducted. For simulation of human dermal exposure to TDI from polyurethane foam, a migration test technique was designed. Emission of TDI to air was determined for a representative FPF using three different emission test cells. Two were commercially available cells that employ air flow over the surface of the foam [the Field and Laboratory Emission Cell (FLEC®) and the Micro-Chamber/Thermal Extraction™ cell]. The third emission test cell was of a custom design and features air flow through the foam sample rather than over the foam surface. Emitted TDI in the air of the test cells was trapped using glass fiber filters coated with 1-(2-methoxyphenyl)-piperazine (MP), a commonly used derivatizing agent for diisocyanates. The filters were subsequently desorbed and analyzed by liquid chromatography/mass spectrometry. Measurement of TDI migration from representative foam was accomplished by placing glass fiber filters coated with MP on the outer surfaces of a foam disk and then compressing the filters against the disk using a clamping apparatus for periods of 8 and 24 h. The sample filters were subsequently desorbed and analyzed in the same manner as for the emission tests. Although the foam tested had detectable levels of solvent-extractable TDI (56ng TDI g(-1) foam for the foam used in emissions tests; 240-2800ng TDI g(-1) foam for the foam used in migration tests), no TDI was detected in any of the emission or migration tests. Method detection limits (MDLs) for the emissions tests ranged from 0.03 to 0.5ng TDI g(-1) foam (0.002-0.04ng TDI cm(-2) of foam surface), whereas those for the migration tests were 0.73ng TDI g(-1) foam (0.16ng TDI cm(-2) of foam surface). Of the three emission test methods used, the FLEC® had the lowest relative MDLs (by a factor of 3-10) by virtue of its high chamber loading factor. In addition, the FLEC® cell offers well-established conformity with emission testing standard methods.

Microstructural Organization of Elastomeric Polyurethanes with Siloxane-Containing Soft Segments

NASA Astrophysics Data System (ADS)

Choi, Taeyi; Weklser, Jadwiga; Padsalgikar, Ajay; Runt, James

2011-03-01

In the present study, we investigate the microstructure of two series of segmented polyurethanes (PUs) containing siloxane-based soft segments and the same hard segments, the latter synthesized from diphenylmethane diisocyanate and butanediol. The first series is synthesized using a hydroxy-terminated polydimethylsiloxane macrodiol and varying hard segment contents. The second series are derived from an oligomeric diol containing both siloxane and aliphatic carbonate species. Hard domain morphologies were characterized using tapping mode atomic force microscopy and quantitative analysis of hard/soft segment demixing was conducted using small-angle X-ray scattering. The phase transitions of all materials were investigated using DSC and dynamic mechanical analysis, and hydrogen bonding by FTIR spectroscopy.

Skin exposure: Assessing the hazard in the workplace

NASA Technical Reports Server (NTRS)

Cummins, Kevin

1994-01-01

An outline of the Occupational Safety and Health Agency's concerns of skin exposure to hazardous chemicals is presented, followed by the corresponding slide narrations. Specifically, dermatitis and skin absorption as compared to lung absorption are addressed. Lung versus skin exposure is examined for glycol ethers and acrylamide. Examples of skin exposure include PBC's in transformers, toluene and xylene from autobody work, polynuclear aromatics (PNA's) among Coke oven workers, toluene diisocyanate (TDI), and occupational chemical exposures in an academic medical center. Permeation through gloves in the semiconductor industry is addressed as evidence for the need to assess the effectiveness of PPE (Personal Protective Equipment). This leads to the revisions of the PPE standard and the Safety and Health Program standard.

Polyurethane foam with multi walled carbon nanotubes/magnesium hybrid filler

NASA Astrophysics Data System (ADS)

Adnan, Sinar Arzuria; Zainuddin, Firuz; Zaidi, Nur Hidayah Ahmad; Akil, Hazizan Md.; Ahmad, Sahrim

2016-07-01

The purpose of this paper is to investigate the effect of multiwalled carbon nanotubes (MWCNTs)/magnesium (Mg) hybrid filler in polyurethane (PU) foams with different weight percentages (0.5 wt.% to 3.0 wt.%). The PU/MWCNTs/Mg foam composites were formed by reaction of based palm oil polyol (POP) with methylene diphenyl diisocyanate (MDI) with ratio 1:1.1 by weight. The foam properties were evaluated in density, morphology and compressive strength. The addition of 2.5 wt.% hybrid filler showed the higher density in 59.72 kg/m3 and thus contribute to the highest compressive strength at 1.76 MPa. The morphology show cell in closed structure and addition hybrid filler showed uneven structure.

Thermoresponsive Polyurethane Bearing Oligo(Ethylene Glycol) as Side Chain Without Polyol at Polymer Backbone Achieved Excellent Hydrophilic and Hydrophobic Switching.

PubMed

Aoki, Daisuke; Ajiro, Hiroharu

2018-06-13

In order to prepare thermoresponsive polyurethane gels, a novel polyurethane bearing oligo(ethylene glycol) (OEG) as the side chain is successfully synthesized with hexamethylene diisocyanate and OEG tartrate ester. The aqueous solution of the polyurethane shows sharp and clear lower critical solution temperature behavior at 34 °C. Furthermore, a hydrogel based on the same polyurethane is also successfully prepared using glycerol as the crosslinker. This polyurethane hydrogel including 10 mol% of glycerol presents a large swelling ratio change between 4 °C and 37 °C from 250% to 40%. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis, Characterization and in Vitro Evaluation of New Composite Bisphosphonate Delivery Systems

PubMed Central

Kolmas, Joanna; Sobczak, Marcin; Olędzka, Ewa; Nałęcz-Jawecki, Grzegorz; Dębek, Cezary

2014-01-01

In this study, new composite bisphosphonate delivery systems were obtained from polyurethanes (PUs) and nanocrystalline hydroxyapatite (HA). The biodegradable PUs were first synthesized from poly(ε-caprolactone) diols (PCL diols), poly(ethylene adipate) diol, 1,6-hexamethylene diisocyanate, 1,4-butanediol and HA. Moreover, the PCL diols were synthesized by the ring-opening polymerization catalysed by the lipase from Candida antarctica. Next, composite drug delivery systems for clodronate were prepared. The mechanical properties of the obtained biomaterials were determined. The cytotoxicity of the synthesized polymers was tested. The preliminary results show that the obtained composites are perspective biomaterials and they can be potentially applied in the technology of implantation drug delivery systems. PMID:25247580

Water- and air-quality and surficial bed-sediment monitoring of the Sweetwater Reservoir watershed, San Diego County, California, 2003-09

USGS Publications Warehouse

Mendez, Gregory O.; Majewski, Michael S.; Foreman, William T.; Morita, Andrew Y.

2015-01-01

Sampling results show concentrations of the gasoline oxygenate methyl tert-butyl ether in water and air samples declined after it was phased out by the State of California in January 2004. The largest concentrations of gasoline hydrocarbons benzene and toluene in water were detected at or near the surface of the SWR. Isophorone and phenol were the two most frequently detected BNA compounds in water. Diuron, prometon, and simazine were the most frequently detected pesticide compounds in water. Concentrations of benzene and toluene in air samples were highest during the cooler months and had a consistent seasonal pattern over time. Ten PAH compounds were detected frequently in air samples. Twelve pesticide compounds were also detected in air samples. Surficial bed-sediment samples were analyzed for 53 PAHs; 22 of the compounds had one or more detections. Surficial bed-sediment samples were analyzed for 22 organic compounds; only 6 compounds had one or more detections. Surficial bed-sediment samples were analyzed for 37 metals.

2,4-Toluene Diisocyanate Detection in Liquid and Gas Environments through Electrochemical Oxidation in an Ionic Liquid

PubMed Central

Lin, Lu; Rehman, Abdul; Chi, Xiaowei; Zeng, Xiangqun

2016-01-01

The electrochemical oxidation of 2,4-toluene diisocyanate (2,4-TDI) in an ionic liquid (IL) has been systematically characterized to determine plausible electrochemical and chemical reaction mechanisms and to define the optimal detection methods for such a highly significant analyte. It has been found that the use of an IL as the electrolyte allows the oxidation of 2,4-TDI to occur at a less positive anodic potential with no side reactions as compared to traditional acetonitrile based electrolytes. UV-Vis, FT-IR, Cyclic Voltammetry and Electrochemical Impedance Spectroscopy (EIS) studies have revealed the unique mechanisms of dimerization of 2,4-TDI at the electrode interface by self-addition reactions, which can be utilized to improve the selectivity of detection. The study of 2,4-TDI redox chemistry further facilitates the development of a robust amperometric sensing methodology by selecting a hydrophobic IL ([C4mpy][NTf2]) and by restricting the potential window to only include the oxidation process. Thus, this innovative electrochemical sensor is capable of avoiding the two most ubiquitous interferents in ambient conditions (i.e. humidity and oxygen), thereby enhancing the sensor performance and reliability for real world applications. The method was established to detect 2,4–TDI in both liquid and gas phases. The limits of detection (LOD) values were 130.2 ppm and 0.7862 ppm, respectively, for the two phases, and are comparable to the safety standards reported by NIOSH. The as-developed 2.4-TDI amperometric sensor exhibits a sensitivity of 1.939 μA/ppm. Moreover, due to the simplicity of design and the use of an IL both as a solvent and non-volatile electrolyte, the sensor has the potential to be miniaturized for smart sensing protocols in distributed sensor applications. PMID:26763507

Biological monitoring of workers exposed to 4,4'-methylenediphenyl diisocyanate (MDI) in 19 French polyurethane industries.

PubMed

Robert, A; Ducos, P; Francin, J M; Marsan, P

2007-04-01

To study the range of urinary levels of 4,4'-methylenedianiline (MDA), a metabolite of methylenediphenyl diisocyanate (MDI), across factories in the polyurethane industries and to evaluate the validity of this biomarker to assess MDI occupational exposure. Workers exposed to MDI, as well as non-occupationally exposed subjects, were studied and pre- and post-shift urine samples were collected from 169 workers of 19 French factories and 120 controls. Details on work activities and practices were collected by a questionnaire and workers were classified into three job categories. The identification and quantification of the total urinary MDA were performed by high-performance liquid chromatography with electrochemical detection (HPLC/EC). For all the factories, MDA was detectable in 73% of the post-shift urine samples. These post-shift values, in the range of <0.10 (detection limit)-23.60 microg/l, were significantly higher than those of the pre-shift samples. Urinary MDA levels in the control group were in the range of < 0.10-0.80 microg/l. The degree of automation of the mixing operation (polyols and MDI) appears as a determinant in the extent of exposure levels. The highest amounts of MDA in urine were found in the spraying or hot processes. The excretion levels of the workers directly exposed to the hardener containing the MDI monomer were significantly higher than those of the other workers. In addition, skin exposure to MDI monomer or to polyurethane resin during the curing step were always associated with significant MDA levels in urine. Total MDA in post-shift urine samples is a reliable biomarker to assess occupational exposure to MDI in various industrial applications and to help factories to improve their manufacturing processes and working practices. A biological guiding value not exceeding 7 microg/l (5 microg/g creatinine) could be proposed in France.

Winner of the society for biomaterials student award in the Ph.D. category for the annual meeting of the society for biomaterials, april 11-14, 2018, Atlanta, GA: Development of a bimodal, in situ crosslinking method to achieve multifactor release from electrospun gelatin.

PubMed

Kishan, Alysha; Walker, Taneidra; Sears, Nick; Wilems, Thomas; Cosgriff-Hernandez, Elizabeth

2018-05-01

To better mimic native tissue microenvironments, current efforts have moved beyond single growth factor delivery to more complex multiple growth factor delivery with distinct release profiles. Electrospun gelatin, a widely investigated drug delivery vehicle, requires postprocessing crosslinking techniques that generate a mesh with uniform crosslinking density, limiting the ability to deliver multiple factors at different rates. Herein, we describe a method to independently control release of multiple factors from a single electrospun gelatin mesh. Two in situ crosslinking modalities, photocrosslinking of methacyrlated gelatin and reactive crosslinking of gelatin with a diisocyanate, are coelectrospun to generate distinct fiber populations with different crosslinking chemistry and density in a single mesh. The photocrosslinked gelatin-methacrylate resulted in a relatively rapid release of a model protein (48 ± 12% at day 1, 96 ± 3% at day 10) due to diffusion of embedded protein from the crosslinked fibers. The reactive crosslinking system displayed a more sustained release (7 ± 5% at day 1, 33 ± 2% at day 10) that was attributed to the conjugation of protein to gelatin with the diisocyanate, requiring degradation of gelatin prior to diffusion out of the fibers. Both modalities displayed tunable release profiles. Subsequent release studies of a cospun mesh with two different crosslinked fiber populations confirmed that the cospun mesh displayed multifactor release with independent release profiles. Overall, this bimodal, in situ crosslinking approach enables the delivery of multiple factors with distinct release kinetics from a single mesh and is expected to have broad utility in tissue engineering. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 106A: 1155-1164, 2018. © 2018 Wiley Periodicals, Inc.

Data on the synthesis and mechanical characterization of polysiloxane-based urea-elastomers prepared from amino-terminated polydimethylsiloxanes and polydimethyl-methyl-phenyl-siloxane-copolymers.

PubMed

Riehle, Natascha; Götz, Tobias; Kandelbauer, Andreas; Tovar, Günter E M; Lorenz, Günter

2018-06-01

This article contains data on the synthesis and mechanical characterization of polysiloxane-based urea-elastomers (PSUs) and is related to the research article entitled "Influence of PDMS molecular weight on transparency and mechanical properties of soft polysiloxane-urea-elastomers for intraocular lens application" (Riehle et al., 2018) [1]. These elastomers were prepared by a two-step polyaddition using the aliphatic diisocyanate 4,4'-Methylenbis(cyclohexylisocyanate) (H 12 MDI), a siloxane-based chain extender 1,3-Bis(3-aminopropyl)-1,1,3,3-tetramethyldisiloxane (APTMDS) and amino-terminated polydimethylsiloxanes (PDMS) or polydimethyl-methyl-phenyl-siloxane-copolymers (PDMS-Me,Ph), respectively. (More details about the synthesis procedure and the reaction scheme can be found in the related research article (Riehle et al., 2018) [1]). Amino-terminated polydimethylsiloxanes with varying molecular weights and PDMS-Me,Ph-copolymers were prepared prior by a base-catalyzed ring-chain equilibration of a cyclic siloxane and the endblocker APTMDS. This DiB article contains a procedure for the synthesis of the base catalyst tetramethylammonium-3-aminopropyl-dimethylsilanolate and a generic synthesis procedure for the preparation of a PDMS having a targeted number average molecular weight M ¯ n of 3000 g mol -1 . Molecular weights and the amount of methyl-phenyl-siloxane within the polysiloxane-copolymers were determined by 1 H NMR and 29 Si NMR spectroscopy. The corresponding NMR spectra and data are described in this article. Additionally, this DiB article contains processed data on in line and off line FTIR-ATR spectroscopy, which was used to follow the reaction progress of the polyaddition by showing the conversion of the diisocyanate. All relevant IR band assignments of a polydimethylsiloxane-urea spectrum are described in this article. Finally, data on the tensile properties and the mechanical hysteresis-behaviour at 100% elongation of PDMS-based polyurea-elastomers are shown in dependence to the PDMS molecular weight.

Human Innate Immune Responses to Hexamethylene Diisocyanate (HDI) and HDI-Albumin Conjugates

PubMed Central

Wisnewski, Adam V.; Liu, Qing; Liu, Jian; Redlich, Carrie A.

2011-01-01

Background Isocyanates, a leading cause of occupational asthma, are known to induce adaptive immune responses; however, innate immune responses, which generally precede and regulate adaptive immunity, remain largely uncharacterized. Objective Identify and characterize cellular, molecular and systemic innate immune responses induced by hexamethylene diisocyanate (HDI). Methods Human peripheral blood mononuclear cells (PBMCs) were stimulated in vitro with HDI-albumin conjugates or control antigen, and changes in phenotype, gene, and protein expression were characterized by flow cytometry, microarray, Western blot and ELISA. Cell uptake of isocyanate was visualized microscopically using HDI-albumin conjugates prepared with fluorescently-labeled albumin. In vivo, human HDI exposure was performed via specific inhalation challenge, and subsequent changes in PBMCs and serum proteins were measured by flow cytometry and ELISA. Genotypes were determined by PCR. Results Human monocytes take-up HDI-albumin conjugates and undergo marked changes in morphology and gene/protein expression in vitro. The most significant (p 0.007 – 0.05) changes in mircoarray gene expression were noted in lysosomal genes, especially peptidases and proton pumps involved in antigen processing. Chemokines that regulate monocyte/macrophage trafficking (MIF, MCP-1), and pattern recognition receptors that bind chitin (chitinases) and oxidized low-density lipoprotein (CD68) were also increased following isocyanate-albumin exposure. In vivo, HDI exposed subjects exhibited an acute increase in the percentage of PBMCs with the same HDI-albumin responsive phenotype characterized in vitro (HLA-DR+/CD11c+ with altered light scatter properties). An exposure-dependent decrease (46±11%; p<0.015) in serum concentrations of chitinase-3-like-1 was also observed, in individuals that lack the major (type 1) human chitinase (due to genetic polymorphism), but not in individuals possessing at least one functional chitinase-1 allele. Conclusions Previously unrecognized innate immune responses to HDI and HDI-albumin conjugates could influence the clinical spectrum of exposure reactions. PMID:18498542

Glass Reinforcement of Various Epoxy Resins-Polyurea Systems

NASA Astrophysics Data System (ADS)

Joshi, Medha; Jauhari, Smita

2012-07-01

Polyureas (PUs) were prepared by the polycondensation reaction of disperse dyes containing -NH2 group and toluene 2, 4-diisocyanate. The disperse dyes have been prepared by coupling of various 2-diazobenzothiazoles with 1,3-benzenediamine. All the PUs were characterized by elemental analysis, spectral studies, number average molecular weight ( {overline{{Mn}} } ), and thermogravimetry. Further reaction of PUs was carried out with an epoxy resin (i.e., DGEBA). The curing study of prepared resins was monitored by differential scanning calorimeter (DSC). Based on DSC, thermograms glass fiber-reinforced composites have been laminated and characterized by chemical, mechanical, and electrical properties. The unreinforced cured resins were subjected to thermogravimetric analysis (TGA). The laminated composites showed excellent resistance properties against chemicals and good mechanical and electrical properties.

Morphological and thermal studies of chitin-curcumin blends derived polyurethanes.

PubMed

Mahmood, Kashif; Zia, Khalid Mahmood; Zuber, Mohammad; Tabasum, Shazia; Rehman, Saima; Zia, Fatima; Noreen, Aqdas

2017-12-01

The present study describes a novel ecofriendly series of chitin/curcumin/1,4-butane diol (BDO) blend derived polyurethanes (PUs), using hydroxy terminated polybutadiene (HTPB) and hexamethylene diisocyanate (HDI) along with different mole ratio of chitin, curcumin and BDO. The structural and morphological elucidation of the prepared films was done by FTIR and SEM techniques. The swelling behavior of the films was analyzed in both water and DMSO, which showed that incorporation of chitin increases the hydrophobicity and decreases the rate of swelling. Thermal analysis of synthesized PU blends revealed better thermal stability with following mole ratio 1:0.5:0.5 of chitin: curcumin: BDO as determined by TGA and DSC techniques. Copyright © 2017 Elsevier B.V. All rights reserved.

Synthesis of a Novel Biodegradable Polyurethane with Phosphatidylcholines

PubMed Central

Cao, Jun; Chen, Niancao; Chen, Yuanwei; Luo, Xianglin

2010-01-01

A novel polyurethane was successfully synthesized by chain-extension of biodegradable poly (l-lactide) functionalized phosphatidylcholine (PC) with hexamethylene diisocyanate (HDI) as chain extender (PUR-PC). The molecular weights, glass transition temperature (Tg) increased significantly after the chain-extension. The hydrophilicity of PUR-PC was better than the one without PC, according to a water absorption test. Moreover, the number of adhesive platelets and anamorphic platelets on PUR-PC film were both less than those on PUR film. These preliminary results suggest that this novel polyurethane might be a better scaffold than traditional biodegradable polyurethanes for tissue engineering due to its better blood compatibility. Besides, this study also provides a new method to prepare PC-modified biodegradable polyurethanes. PMID:20480047

Chitin based polyurethanes using hydroxyl terminated polybutadiene, part III: surface characteristics.

PubMed

Zia, Khalid Mahmood; Zuber, Mohammad; Saif, Muhammad Jawwad; Jawaid, Mohammad; Mahmood, Kashif; Shahid, Muhammad; Anjum, Muhammad Naveed; Ahmad, Mirza Nadeem

2013-11-01

Hydroxy terminated polybutadiene (HTPB)-chitin based polyurethanes (PUs) with controlled hydrophobicity were synthesized using HTPB and toluene diisocyanate (TDI). The prepolymer was extended with different mass ratios of chitin and 1,4-butane diol (BDO). The effect of chitin contents in chain extender (CE) proportions on surface properties was studied and investigated. Incorporation of chitin contents into the final PU showed decrease in contact angle value of water drop, water absorption (%) and swelling behavior. The antibacterial activity of the prepared samples was affected by varying the chitin contents in the chemical composition of the final PU. The results demonstrated that the use of prepared material can be suggested as non-absorbable suture. Copyright © 2013 Elsevier B.V. All rights reserved.

[Immobilization of pectawamorine G10x on silichromes].

PubMed

Bogatskiĭ, A V; Davidenko, T I; Gren', T A

1980-01-01

Immobilization of pectawamorine G10x on silochromes, using cyanuric chloride, 2,4-toluylene diisocyanate, glutaric dialdehyde, thionyl chloride, phosphorus tribromide, titanium tetrachloride, zirconium oxychloride and hafnium oxychloride was studied. The use of glutaric dialdehyde assured the strongest binding and the preatest stability of activity. Properties of the native pectawamorine G10x and immobilized preparations were studied on a comparative basis. Pectawamorine G10x immobilized by means of hafnium oxychloride showed increased stability when stored at 5 degrees C and used repeatedly. In every case, except for cyanuric chloride and glutaric dialdehyde, maximum activity was at a temperature 10 degrees C higher than for the native enzyme, and optimum pH varied for the preparations with different binding reagents.

Synthesis of cellulose diacetate based copolymer electrospun nanofibers for tissues scaffold

NASA Astrophysics Data System (ADS)

Liang, Wencheng; Hou, Jia; Fang, Xiangchen; Bai, Fudong; Zhu, Tonghe; Gao, Feifei; Wei, Chao; Mo, Xiumei; Lang, Meidong

2018-06-01

In this study, a novel cellulose diacetate based copolymer used as tissues scaffold, cellulose diacetate-graft-poly(ethylene terephthalate) (CDA-g-PET) was developed by "graft onto" strategy using 3-Isocyanatomethyl-3,5,5-trimethylcyc-lohexyl isocyanate (IPDI) as a coupling reagent of cellulose diacetate and poly(ethylene terephthalate), and using dibutyltin dilaurate (DBTDL) and 1-butyl-3-methylimidazolium chloride salt ([Bmim]Cl) as catalysts. CDA-g-PET copolymers with five different grafting ratios were obtained by the regulation of the reaction time. It was proved by the FT-IR spectra of the purified copolymers that PET had been successfully grafted onto CDA backbone. Afterwards, CDA-g-PET nanofibers were fabricated via electrospinning and further were cross-linked by means of treating in glutaraldehyde (25%wt) aqueous solution for 48 h. The uniform and smooth fiber morphology was proved by SEM and the diameter decreased with the increase of grafting ratio. Moreover, the value of TGA revealed that the grafting PET onto CDA backbone would improve heat-resistant quality of CDA and help to improve the ability of thermo processing. The graft of PET onto CDA significantly enhanced mechanical property of copolymer compared with CDA. The results of hemolysis ratio indicated that hemolysis ratio has decreased compared with CDA, highlighting the potential application in the field of contacting with blood. In vitro cell viability indicated that CDA-g-PET would enhance biocompatibility compared with CDA.

Characterization of poly(L-lactide/Propylene glycol) based polyurethane films using ATR-FTIR spectroscopy

NASA Astrophysics Data System (ADS)

Manap, Siti Munirah; Ahmad, Azizan; Anuar, Farah Hannan

2016-11-01

A polyurethane films consisting of PLLA, PPG and PLLA-PPG were prepared using solution casting method. Three types of polyurethane were prepared: PPLA:PMDI, PPG:PMDI and PLLA-PPG:PMDI in the presence of polymeric diphenylmethane diisocyanate (PMDI) as the coupling agent and catalyst, Sn(Oct)2. The aim of this research was to improve the physicals properties of PLLA and PPG homopolymers through copolymerization between the two polymers. The homopolymers and polyurethane films were characterized using ATR-FTIR spectroscopy. Chemical reaction between PLLA, PPG and PMDI before and after the reaction were confirmed by observing the shifting of wavenumber for the carbonyl and ether group. Other than that, the additional band for N-H after the reaction indicated that the reaction was successful.

Physical Training Methods For Mine Rescuers In 2015

NASA Astrophysics Data System (ADS)

Marin, Laurentiu; Pavel, Topala; Marin, Catalina Daniela; Sandu, Teodor

2015-07-01

Research and development activities presented were aimed at obtaining a nanocomposite polyurethane matrix with special anti-wear, anti-slip and fire-resistant properties. Research and development works were materialized by obtaining polyurethane nanocomposite matrix, by its physico-chemical modification in order to give the desired technological properties and by characterization of the obtained material. Polyurethane nanocomposite matrix was obtained by reacting a PETOL 3 type polyetherpolyol (having a molecular weight of 5000 UAM) with a diisocyanate under well-established reaction conditions. Target specific technological properties were obtained by physical and chemical modification of polyurethane nanocomposite matrix. The final result was getting a pellicle material based on modified nanocomposite polyurethane, with anti-wear, anti-slip and fire-resistant properties, compatible with most substrates encountered in civil and industrial construction: wood, concrete, metal.

Contact allergy to epoxy hardeners.

PubMed

Aalto-Korte, Kristiina; Suuronen, Katri; Kuuliala, Outi; Henriks-Eckerman, Maj-Len; Jolanki, Riitta

2014-09-01

Diglycidylether of bisphenol A resin is the most important sensitizer in epoxy systems, but a minority of patients develop concomitant or solitary contact allergy to epoxy hardeners. At the Finnish Institute of Occupational Health, several in-house test substances of epoxy hardeners have been tested in a special epoxy compound patch test series. To analyse the frequency and clinical relevance of allergic reactions to different epoxy hardeners. Test files (January 1991 to March 2013) were screened for contact allergy to different epoxy hardeners, and the clinical records of patients with allergic reactions were analysed for occupation, concomitant allergic reactions, and exposure. The most commonly positive epoxy hardeners were m-xylylenediamine (n = 24), 2,4,6-tris-(dimethylaminomethyl)phenol (tris-DMP; n = 14), isophorone-diamine (n = 12), and diethylenetriamine (n = 9). Trimethylhexamethylenediamine (n = 7), tetraethylenepentamine (n = 4), and triethylenetetramine (n = 2) elicited some reactions, although most patients were found to have no specific exposure. Allergic reactions to hexamethylenetetramine, dimethylaminopropylamine and ethylenediamine dihydrochloride were not related to epoxy products. Tris-DMP is an important sensitizer in epoxy hardeners, and should be included in the patch test series of epoxy chemicals. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Syringaresinol: A Renewable and Safer Alternative to Bisphenol A for Epoxy-Amine Resins.

PubMed

Janvier, Marine; Hollande, Louis; Jaufurally, Abdus Samad; Pernes, Miguel; Ménard, Raphaël; Grimaldi, Marina; Beaugrand, Johnny; Balaguer, Patrick; Ducrot, Paul-Henri; Allais, Florent

2017-02-22

A renewable bisepoxide, SYR-EPO, was prepared from syringaresinol, a naturally occurring bisphenol deriving from sinapic acid, by using a chemo-enzymatic synthetic pathway. Estrogenic activity tests revealed no endocrine disruption for syringaresinol. Its glycidylation afforded SYR-EPO with excellent yield and purity. This biobased, safe epoxy precursor was then cured with conventional and renewable diamines for the preparation of epoxy-amine resins. The resulting thermosets were thermally and mechanically characterized. Thermal analyses of these new resins showed excellent thermal stabilities (T d5 % =279-309 °C) and T g ranging from 73 to 126 °C, almost reaching the properties of those obtained with the diglycidylether of bisphenol A (DGEBA), extensively used in the polymer industry (T d5 % =319 °C and T g =150 °C for DGEBA/isophorone diamine resins). Degradation studies in NaOH and HCl aqueous solutions also highlighted the robustness of the syringaresinol-based resins, similar to bisphenol A (BPA). All these results undoubtedly confirmed the potential of syringaresinol as a greener and safer substitute for BPA. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Changes in growth, hormones levels and essential oil content of Ammi visnaga L. plants treated with some bioregulators

PubMed Central

Talaat, Iman M.; Khattab, Hemmat I.; Ahmed, Aisha M.

2013-01-01

The effects of foliar application of different concentrations of amino acids (tyrosine and phenylalanine) and phenolic acids (trans-cinnamic acid, benzoic acid and salicylic acid) on growth, pigment content, hormones levels and essential oil content of Ammi visnaga L were carried out during two successive seasons. It is clear that foliar application of either amino acids or phenolics significantly promoted the growth parameters in terms of shoot height, fresh and dry biomass, number of branches and number of umbels per plant. The increment of growth parameter was associated with elevated levels of growth promoters (IAA, GA3, total cytokinins) and low level of ABA. The greatest increase in the previously mentioned parameters was measured in plants exposed to different concentrations of phenols particularly in benzoic acid-treated plants. Such effect was concentration dependent. All treatments led to significant increments in yield seeds and oil content. Moreover, gas liquid chromatographic analysis revealed that the main identified components of essential oil were 2,2-dimethyl butanoic acid, isobutyl isobutyrate, α-isophorone, thymol, fenchyl acetate and linalool. Phenolics and amino acid treatments resulted in qualitative differences in these components of essential oil. PMID:25183946

Composition of sulla (Hedysarum coronarium L.) honey solvent extractives determined by GC/MS: norisoprenoids and other volatile organic compounds.

PubMed

Jerković, Igor; Tuberoso, Carlo I G; Tuberso, Carlo I G; Gugić, Mirko; Bubalo, Dragan

2010-09-09

Samples of unifloral sulla (Hedysarum coronarum L.) honey from Sardinia (Italy) were analysed. To investigate the chemical composition of the honey volatiles two solvent systems were used for ultrasonic solvent extraction (USE): 1) a 1:2 (v/v) pentane and diethyl ether mixture and 2) dichloromethane. All the extracts were analysed by GC and GC/MS. These procedures have permitted the identification of 56 compounds that include norisoprenoids, benzene derivatives, aliphatic compounds and Maillard reaction products. Norisoprenoids were the major compounds in both extracts, dominated by vomifoliol (5.3-11.2%; 9.6-14.0%) followed by minor percentages of other norisoprenoids such as α-isophorone, 4-ketoisophorone, 3-oxo-α-ionol or 3-oxo-α-ionone. Other abundant single compounds in the extracts were 3-hydroxy-4-phenylbutan-2-one (0.8-5.4%; 0.6-5.7%) and methyl syringate (3.0-5.7%; 2.2-4.1%). The composition of the volatiles and semi-volatiles in the obtained extracts suggests that sulla honey is quite distinctive relative to the other honeys that have been chemically studied by GC/MS, but no specific markers of the honey botanical origin were found.

Evaluation of organic-vapor respirator cartridge efficiency for toluene diisocyanate vapor in the presence of methylenechloride or acetone solvent.

PubMed

Dharmarajan, Venkatram; Cummings, Barbara; Lingg, Robert D

2003-08-01

Toluene diisocyanate (TDI) is a widely used raw material in the manufacture of flexible polyurethane foams. Acetone (ACE) and/or methylenechloride (MECL) solvents are the most commonly used solvent-based blowing agents for TDI foams. ACGIH has recommended a TWA exposure limit of 5 ppb for TDI and 500 ppm for ACE. For MECL, OSHA mandates a TWA-exposure limit of 25 ppm. This study evaluated the ability of the organic-vapor respirator cartridges (OVC) to block TDI, as well as the effect of airborne MECL or ACE on the OVCs' efficiency to capture TDI. An aluminum/stainless steel exposure chamber was constructed for simultaneously challenging OVCs in triplicate with a dynamic atmosphere of TDI and ACE or MECL vapor. The challenge atmosphere was generated by combining a TDI-laden nitrogen stream from the headspace of a heated impinger with a humidified stream of the indicated solvent in air. The average challenge concentration for TDI was 275 ppb. The average MECL or ACE concentrations were 547 and 581 ppm, respectively. The challenge atmosphere at room temperature (approximately 24 degrees C) and at 25 or 80 percent relative humidity was drawn through each cartridge at 32 L/min for 40+ hours. During the last 8 hours of the challenge, the atmosphere had only TDI vapor. The pre- and post-cartridge atmospheres were periodically sampled for TDI and solvent. Five tests were conducted--two with MSA and three with North OVCs. Under these extreme test conditions no TDI breakthrough was detected from any OVC. The average-calculated efficiency of the OVCs for TDI was >99.9+ percent. Within the first 6 hours of the challenge the cartridges were saturated with ACE or MECL; nevertheless, continued challenging with TDI and solvents did not cause any TDI breakthrough. The study demonstrates that with an OSHA-compliant respiratory protection program, an OVC can safely be used for 40 hours in most polyurethane foam operations. In typical occupational environments using TDI and solvents, the solvent breakthrough, rather than TDI breakthrough, would be the determining factor for the calculation of respirator cartridge change-out schedules.

Evaluation of anti-asthmatic and antioxidant potential of Boerhavia procumbens in toluene diisocyanate (TDI) treated rats.

PubMed

Bokhari, Jasia; Khan, Muhammad Rashid

2015-08-22

Asthma is an ailment of airways characterized by activation of the T helper (Th) 2 lymphocytes and subsequent movement of inflammatory cells. Boerhavia procumbens of family Nyctaginaceae is locally used for the treatment of asthma, cough, hemorrhoids, dropsy, cardiac, eyes and kidney problems. We have evaluated its methanol extract (BPM) as a therapeutic candidate for asthma against toluene diisocyanate (TDI) allergic model in rat. The BPM extract was obtained from the whole plant of B. procumbens in methanol. Sprague-Dawley male 36 rats (200-250 g) were categorized into 6 groups having six rats in each category. The animals were provoked (10%) and sensitized (5%) by TDI. Animals of groups I-III were vehicle control (ethyl acetate), diseased control (TDI) and reference control (TDI+dexamethasone {2.5mg/kg bw}), respectively. Animals of group IV (TDI+200mg/kg bw) and group V (TDI+400mg/kg bw) were administered with BPM whereas group VI was administered with 400mg/kg bw alone of BPM. Protective effects of BPM were determined by counting the number of leucocytes and estimation of interleukines in blood, bronchoalveolar lavage (BAL) and in in vitro culture of spleen cells. Estimation of antioxidant enzymes, lipid peroxides and H2O2 and histopathology of lungs were carried out for antioxidant potential of plant extract used. Methanol extract of B. procumbens suppressed the asthmatic symptoms and inhibited the infiltration of eosinophils and lymphocytes in lungs of TDI provoked rats. Administration of BPM to TDI provoked rats, dose dependently, inhibited the release of interleukins (IL)-2 in serum and IL-4, IL-6 interferon gamma (IFN-γ) in bronchoalveolar lavage (BAL) and in in vitro culture of spleen cells, and ameliorated the oxidative stress in lung tissues. Quantitative scoring of the lung histopathology exhibited protective effects of BPM and the inflammation, mucus, thickening of peribronchial smooth muscle layer and subepithelial deposition of collagen induced with TDI were ameliorated. The BPM has the anti-inflammatory properties that may be used to treat the asthma and inflammatory related ailments. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Association of respiratory symptoms and asthma with occupational exposures: findings from a population-based cross-sectional survey in Telemark, Norway

PubMed Central

Abrahamsen, R; Fell, A K M; Svendsen, M V; Andersson, E; Torén, K; Henneberger, P K; Kongerud, J

2017-01-01

Objectives The aim of this study was to estimate the prevalence of respiratory symptoms and physician-diagnosed asthma and assess the impact of current occupational exposure. Design Cross-sectional analyses of the prevalence of self-reported respiratory health and association with current occupational exposure in a random sample of the general population in Telemark County, Norway. Settings In 2013, a self-administered questionnaire was mailed to a random sample of the general population, aged 16–50, in Telemark, Norway. The overall response rate was 33%, comprising 16 099 responders. Outcome measures The prevalence for respiratory symptoms and asthma, and OR of respiratory symptoms and asthma for occupational groups and exposures were calculated. Occupational exposures were assessed using self-reported exposure and an asthma-specific job-exposure matrix (JEM). Results The prevalence of physician-diagnosed asthma was 11.5%. For the occupational groups, the category with agriculture/fishery workers and craft/related trade workers was associated with wheezing and asthma attack in the past 12 months, showing OR 1.3 (1.1 to 1.6) and 1.9 (1.2 to 2.8), respectively. The group including technicians and associated professionals was also associated with wheezing OR 1.2 (1.0 to 1.3) and asthma attack OR 1.4 (1.1 to 1.9). The JEM data show that exposure to flour was associated with wheezing OR 3.2 (1.4 to 7.3) and woken with dyspnoea OR 3.5 (1.3 to 9.5), whereas exposures to diisocyanates, welding/soldering fumes and exposure to vehicle/motor exhaust were associated with dyspnoea OR 2.9 (1.5 to 5.7), 3.2 (1.6 to 6.4) and 1.4 (1.0 to 1.8), respectively. Conclusions The observed prevalence of physician-diagnosed asthma was 11.5%. The ‘manual’ occupations were associated with respiratory symptoms. Occupational exposure to flour, diisocyanates, welding/soldering fumes and vehicle/motor exhaust was associated with respiratory symptoms in the past 12 months and use of asthma medication. However, prospective data are needed to confirm the observed associations. PMID:28336744

Characterization of multiblock copolymers by chromatographic techniques.

PubMed

N'Goma, Patrick Yoba; Radke, Wolfgang; Malz, Frank; Ziegler, Hans Jörg; Zierke, Michael; Behl, Marc; Lendlein, Andreas

2011-02-01

Multiblock copolymers (MBC) composed of blocks of poly(1,4-dioxanone) (PPDO) and poly(e-caprolactone) (PCL) were investigated in order to gain information on the extend of chemical heterogeneity of the samples. A gradient chromatographic method was established allowing separation of purely PPDO- from purely PCL-containing chains. Application of the gradient to MBC made of PPDO- and PCL-diols connected by trimethylhexamethylene diisocyanate (TMDI) resulted in two well separated peaks which were analyzed by means of FTIR, 1H-NMR and pyrolysis GC-MS. It was shown that the first peak was composed to a large extent of PPDO and only lower amounts of PCL were incorporated. Conversely, the second peak consisted predominantly of PCL with only a minor fraction of PPDO. Thus, the MBCs having PPDO and PCL segments show an unexpected broad chemical heterogeneity.

Theoretical Evaluation of Crosslink Density of Chain Extended Polyurethane Networks Based on Hydroxyl Terminated Polybutadiene and Butanediol and Comparison with Experimental Data

NASA Astrophysics Data System (ADS)

Sekkar, Venkataraman; Alex, Ancy Smitha; Kumar, Vijendra; Bandyopadhyay, G. G.

2018-01-01

Polyurethane networks between hydroxyl terminated polybutadiene (HTPB) and butanediol (BD) were prepared using toluene diisocyanate (TDI) as the curative. HTPB and BD were taken at equivalent ratios viz.: 1:0, 1:1, 1:2, 1:4, and 1:8. Crosslink density (CLD) was theoretically calculated using α-model equations developed by Marsh. CLD for the polyurethane networks was experimentally evaluated from equilibrium swell and stress-strain data. Young's modulus and Mooney-Rivlin approaches were adopted to calculate CLD from stress-strain data. Experimentally obtained CLD values were enormously higher than theoretical values especially at higher BD/HTPB equivalent ratios. The difference in the theoretical and experimental values for CLD was explained in terms of local crystallization due to the formation of hard segments and hydrogen bonded interactions.

Organically Modified Nanoclay-Reinforced Rigid Polyurethane Films

NASA Astrophysics Data System (ADS)

Park, Yong Tae; Qian, Yuqiang; Lindsay, Chris; Stein, Andreas; Macosko, Christopher

2012-02-01

The nanodispersion of vermiculite in polyurethanes was investigated to produce organoclay-reinforced rigid gas barrier films. Reducing gas transport can improve the insulation performance of closed cell polyurethane foam. In a previous study, the dispersion of vermiculite in polyurethanes without organic modification was not sufficient due to the non-uniform dispersion morphology. When vermiculite was modified by cation exchange with long-chain quaternary ammonium cations, the dispersion in methylene diphenyl diisocyanate (MDI) was significantly improved. Dispersion was improved by combining high intensity dispersive mixing with efficient distributive mixing. Polymerization conditions were also optimized in order to provide a high state of nanodispersion in the polyurethane nanocomposite. The dispersions were characterized using rheological, microscopic and scattering/diffraction techniques. The final nanocomposites showed enhancement of mechanical properties and reduction in permeability to carbon dioxide at low clay concentration (around 2 wt percent).

Enhancement of the Mechanical Properties of a Polylactic Acid/Flax Fiber Biocomposite by WPU, WPU/Starch, and TPS Polyurethanes Using Coupling Additives

NASA Astrophysics Data System (ADS)

Miskolczi, N.; Sedlarik, V.; Kucharczyk, P.; Riegel, E.

2018-01-01

This work is addressed to the synthesis of bio-based polymers and investigation of their application in a flax-fiber-reinforced polylactic acid. Polyurethane polymers were synthesized from polyphenyl-methane-diisocyanate, poly (ethylene oxide) glycol, and ricinoleic acid, and their structure was examined by the Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. It was established that the introduction of flax fibers and different compatibilizers into the polymers improved their mechanical properties. A vinyl-trimetoxy-silane and polyalkenyl-polymaleic-anhydride derivative with a high acid number produced the best effect on the properties, but samples without additives had the highest water absorption capacity. SEM micrographs showed a good correlation between the morphology of fracture structure of the composites and the mechanical properties of flax fibers.

Fire and heat resistant laminating resins based on maleimido and citraconimido substituted 1-(diorgano oxyphosphonyl) methyl -2,4- and -2,6- diaminobenzenes

NASA Technical Reports Server (NTRS)

Mikroyannidis, John A. (Inventor); Kourtides, Demetrius A. (Inventor)

1987-01-01

A class of fire and heat resistant bisimide resins prepared by thermal polymerization of maleimido or citraconimido substituted 1-((dialkoxyphosphonyl) methyl)-2-4 and -2,6-diaminobenzenes are described. The polymer precursors are prepared by reacting 1-((diorganooxyphosphonyl) methyl)-2-4 and -2,6-diaminobenzenes with maleic anhydride or citraconic anhydride in a mole ratio 1:2. Chain extension of the monomers is achieved by reacting the mono-N-maleimido derivatives of 1-((diorganooxyphosphonyl) methyl)-2,4 and -2,6-diaminobenzenes with aryl tetracarboxylic dianhydrides, such as benzophenone tetracarbocylic dianhydride, or aryl diisocyanates, such as methylenebis (4-phenylisocyanate), in a mole ratio 2:1. The polymerization of the monomers is studied by differential scanning calorimetry (DSC) and the thermal stability of the polymers is ascertained by thermogravimetric analysis (TGA).

The Effect of Microporous Polymeric Support Modification on Surface and Gas Transport Properties of Supported Ionic Liquid Membranes.

PubMed

Akhmetshina, Alsu A; Davletbaeva, Ilsiya M; Grebenschikova, Ekaterina S; Sazanova, Tatyana S; Petukhov, Anton N; Atlaskin, Artem A; Razov, Evgeny N; Zaripov, Ilnaz I; Martins, Carla F; Neves, Luísa A; Vorotyntsev, Ilya V

2015-12-30

Microporous polymers based on anionic macroinitiator and toluene 2,4-diisocyanate were used as a support for 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF₆]) and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([emim][Tf₂N]) immobilization. The polymeric support was modified by using silica particles associated in oligomeric media, and the influence of the modifier used on the polymeric structure was studied. The supported ionic liquid membranes (SILMs) were tested for He, N₂, NH₃, H₂S, and CO₂ gas separation and ideal selectivities were calculated. The high values of ideal selectivity for ammonia-based systems with permanent gases were observed on polymer matrixes immobilized with [bmim][PF₆] and [emim][Tf₂N]. The modification of SILMs by nanosize silica particles leads to an increase of NH₃ separation relatively to CO₂ or H₂S.

Application of high-strength biodegradable polyurethanes containing different ratios of biobased isomannide and poly (ϵ-caprolactone) diol

PubMed Central

Lim, Dong-In; Park, Hyung-Seok; Park, Jeong-Hui; Knowles, Jonathan C

2013-01-01

Biodegradable–biocompatible polyurethanes were prepared with fixed hexamethylene diisocyanate and varying ratios of isomannide and poly(ϵ-caprolactone) diol using a simple one-step polymerization without a catalyst. The polyurethane structures were confirmed by 1H-nuclear magnetic resonance, Fourier transform infrared spectroscopy, and gel permeation chromatography. The glass transition temperatures were determined by thermal analysis to be between 25°C and 30°C. Degradation tests performed at 37°C in phosphate buffer produced mass losses of 5%–10% after 8 weeks. After 5 days of culture, using osteoblastic cells, the relative cell number on all the polyurethane films was only slightly lower than that of an optimized tissue culture plastic. These polymers offer significant promise with a simplistic synthesis and controlled degradation. PMID:25076809

[Determination of nitroaromatics and cyclo ketones in sea water' by gas chromatography coupled with activated carbon fiber solid-phase micro-extraction].

PubMed

Ma, Hanna; Zhu, Mengya; Wang, Yalin; Sun, Tonghua; Jia, Jinping

2009-05-01

A gas chromatography (GC) coupled with solid-phase micro-extraction using a special activated carbon fiber (ACF) was developed for the analysis of 6 nitroaromatics and cyclic ketones, nitrobenzene (NB), 1,3-dinitrobenzene (1,3-DNB), 2,4-dinitrotoluene (2,4-DNT), 2,6-dinitrotoluene (2,6-DNT), isophorone, 1,4-naphthaquinone (1,4-NPQ), in sea water samples. The sample was extracted for 30 min under saturation of NaCl at 1,500 r/min and 60 degrees C in head space. The desorption was performance at 280 degrees C for 2 min. The linear ranges were from 0.01 to 400 microg/L. The limits of detection (LODs) were 1.4 - 3.2 ng/L. This method has been successfully applied to the determination of nitroaromatics and cyclic ketones in the sea water samples obtained from East China Sea. The concentrations of nitrobenzene, 1,3-dinitrobenzene and 2,6-dinitrotoluene in the sea water sample were 0.756, 0.944, 0.890 microg/L, respectively. The recoveries were 86.3% - 101.8% with the relative standard deviations (RSDs) of 3.7% -7.8%. The method is suitable for analyzing nitroaromatics and cyclic ketones at low concentration levels in sea water samples.

Study of Reactive Melt Processing Behavior of Externally Plasticized Cellulose Acetate in Presence of Isocyanate

PubMed Central

Erdmann, Rafael; Kabasci, Stephan; Kurek, Joanna; Zepnik, Stefan

2014-01-01

Two types of externally plasticized cellulose acetate (CA) were chemically modified using 4,4'-methylene diphenyl diisocyanate (MDI) as crosslinking agent. Crosslinking was performed in the molten state by means of melt mixing in an internal mixer. The viscoelastic properties of the non-crosslinked, externally plasticized CA show typical temperature dependence, similar to conventional thermoplastics. A strong increase in storage modulus is observed with increasing crosslink density indicating that the crosslinked compounds exhibit predominately elastic response. The complex viscosity also increases considerably with increasing crosslink density and does not reach the typical Newtonian plateau at low radial frequencies any more. The viscoelastic properties correlate well with the data recorded online during reactive melt processing in the internal mixer. In comparison to the non-crosslinked CA, the crosslinked compounds show higher glass transition temperature, higher VICAT softening temperatures, improved thermal stability and lower plasticizer evaporation at evaluated temperatures. PMID:28788273

Liquefaction of kenaf (Hibiscus cannabinus L.) core for wood laminating adhesive.

PubMed

Juhaida, M F; Paridah, M T; Mohd Hilmi, M; Sarani, Z; Jalaluddin, H; Mohamad Zaki, A R

2010-02-01

A study was carried out to produce polyurethane (PU) as a wood laminating adhesive from liquefied kenaf core (LKC) polyols by reacting it with toluene-2,4-diisocyanate (TDI) and 1,4-butanediol (BDO). The LKC polyurethane (LKCPU) adhesive has a molecular weight (MW) of 2666, viscosity of 5370 mPa s, and solids content of 86.9%. The average shear strength of the rubberwood (RW) bonded with LKCPU adhesive was 2.9 MPa. Most of the sheared specimens experienced a total adhesive failure. The formation of air bubbles through the liberation of carbon dioxide was observed to reduce the adhesive penetration and bonding strength which was obviously seen on the sheared specimens. The percentage of catalyst used can be varied based on the usage and working time needed. Nonetheless, the physical properties of LKCPU produced in this work had shown good potential as edge-bonding adhesive.

TiO2@TDI@DMAPA: an amine-modified nanoparticle, tailored to act as an economic basic heterogeneous nanocatalyst

NASA Astrophysics Data System (ADS)

Esfahanian, Farzane; Amoozadeh, Ali; Bitaraf, Mehrnoosh

2018-06-01

This study has represented an easy and inexpensive method for the synthesis of a new basic nanocatalyst. In this regard, 3-dimethylaminopropylamine (DMAPA), an economic, industrial, and readily obtainable basic compound, has been grafted onto nano-titania particles by the use of 2,4-toluene diisocyanate (TDI) as a bi-functional, inexpensive, and highly reactive linker. The prepared catalyst has been characterized using the spectroscopic FT-IR method, XRD, FE-SEM, EDX, and back titration. Furthermore, it was identified as an effective catalyst in the preparation of DHPM derivatives and pyranopyrazoles which results in high purity and high yields of products. Response surface methodology (RSM) based on a central composite design (CCD) was employed to reach the optimal conditions. The catalyst can be readily separated and recycled up to six times. [Figure not available: see fulltext.

The Effect of Microporous Polymeric Support Modification on Surface and Gas Transport Properties of Supported Ionic Liquid Membranes

PubMed Central

Akhmetshina, Alsu A.; Davletbaeva, Ilsiya M.; Grebenschikova, Ekaterina S.; Sazanova, Tatyana S.; Petukhov, Anton N.; Atlaskin, Artem A.; Razov, Evgeny N.; Zaripov, Ilnaz I.; Martins, Carla F.; Neves, Luísa A.; Vorotyntsev, Ilya V.

2015-01-01

Microporous polymers based on anionic macroinitiator and toluene 2,4-diisocyanate were used as a support for 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]) and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([emim][Tf2N]) immobilization. The polymeric support was modified by using silica particles associated in oligomeric media, and the influence of the modifier used on the polymeric structure was studied. The supported ionic liquid membranes (SILMs) were tested for He, N2, NH3, H2S, and CO2 gas separation and ideal selectivities were calculated. The high values of ideal selectivity for ammonia-based systems with permanent gases were observed on polymer matrixes immobilized with [bmim][PF6] and [emim][Tf2N]. The modification of SILMs by nanosize silica particles leads to an increase of NH3 separation relatively to CO2 or H2S. PMID:26729177

Acceleration of a ground-state reaction by selective femtosecond-infrared-laser-pulse excitation

NASA Astrophysics Data System (ADS)

Stensitzki, Till; Yang, Yang; Kozich, Valeri; Ahmed, Ashour A.; Kössl, Florian; Kühn, Oliver; Heyne, Karsten

2018-02-01

Infrared (IR) excitation of vibrations that participate in the reaction coordinate of an otherwise thermally driven chemical reaction are believed to lead to its acceleration. Attempts at the practical realization of this concept have been hampered so far by competing processes leading to sample heating. Here we demonstrate, using femtosecond IR-pump IR-probe experiments, the acceleration of urethane and polyurethane formation due to vibrational excitation of the reactants for 1:1 mixtures of phenylisocyanate and cyclohexanol, and toluene-2,4-diisocyanate and 2,2,2-trichloroethane-1,1-diol, respectively. We measured reaction rate changes upon selective vibrational excitation with negligible heating of the sample and observed an increase of the reaction rate up to 24%. The observation is rationalized using reactant and transition-state structures obtained from quantum chemical calculations. We subsequently used IR-driven reaction acceleration to write a polyurethane square on sample windows using a femtosecond IR pulse.

Fast-responding bio-based shape memory thermoplastic polyurethanes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petrovic, Zoran S.; Milic, Jelena; Zhang, Fan

Fast response shape-memory polyurethanes were prepared from bio-based polyols, diphenyl methane diisocyanate and butane diol. The bio-based polyester polyols were synthesized from 9-hydroxynonanoic acid, a product obtained by ozonolysis of fatty acids extracted from soy oil and castor oil. The morphology of polyurethanes was investigated by synchrotron ultra-small angle X-ray scattering, which revealed the inter-domain spacing between the hard and soft phases, the degree of phase separation, and the level of intermixing between the hard and soft phases. We also conducted thorough investigations of the thermal, mechanical, and dielectric properties of the polyurethanes, and found that high crystallization rate ofmore » the soft segment gives these polyurethanes unique properties suitable for shapememory applications, such as adjustable transition temperatures, high degree of elastic elongations, and good mechanical strength. In conclusion, these materials are also potentially biodegradable and biocompatible, therefore suitable for biomedical and environmental applications.« less

Study of Reactive Melt Processing Behavior of Externally Plasticized Cellulose Acetate in Presence of Isocyanate.

PubMed

Erdmann, Rafael; Kabasci, Stephan; Kurek, Joanna; Zepnik, Stefan

2014-12-04

Two types of externally plasticized cellulose acetate (CA) were chemically modified using 4,4'-methylene diphenyl diisocyanate (MDI) as crosslinking agent. Crosslinking was performed in the molten state by means of melt mixing in an internal mixer. The viscoelastic properties of the non-crosslinked, externally plasticized CA show typical temperature dependence, similar to conventional thermoplastics. A strong increase in storage modulus is observed with increasing crosslink density indicating that the crosslinked compounds exhibit predominately elastic response. The complex viscosity also increases considerably with increasing crosslink density and does not reach the typical Newtonian plateau at low radial frequencies any more. The viscoelastic properties correlate well with the data recorded online during reactive melt processing in the internal mixer. In comparison to the non-crosslinked CA, the crosslinked compounds show higher glass transition temperature, higher VICAT softening temperatures, improved thermal stability and lower plasticizer evaporation at evaluated temperatures.

Self-repairable polyurethane networks by atmospheric carbon dioxide and water.

PubMed

Yang, Ying; Urban, Marek W

2014-11-03

Sugar moieties were incorporated into cross-linked polyurethane (PUR) networks in an effort to achieve self-repairing in the presence of atmospheric carbon dioxide (CO2) and water (H2O). When methyl-α-D-glucopyranoside (MGP) molecules are reacted with hexamethylene diisocyanate trimer (HDI) and polyethylene glycol (PEG) to form cross-linked MGP-polyurethane (PUR) networks, these materials are capable of self-repairing in air. This process requires atmospheric amounts of CO2 and H2O, thus resembling plant behavior of carbon fixation during the photosynthesis cycle. Molecular processes responsible for this unique self-repair process involve physical diffusion of cleaved network segments as well as the formation of carbonate and urethane linkages. Unlike plants, MGP-PUR networks require no photo-initiated reactions, and they are thus capable of repair in darkness under atmospheric conditions. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Control of Mechanical Properties of Thermoplastic Polyurethane Elastomers by Restriction of Crystallization of Soft Segment

PubMed Central

Kojio, Ken; Furukawa, Mutsuhisa; Nonaka, Yoshiteru; Nakamura, Sadaharu

2010-01-01

Mechanical properties of thermoplastic polyurethane elastomers based on either polyether or polycarbonate (PC)-glycols, 4,4’-dipheylmethane diisocyanate (1,1’-methylenebis(4-isocyanatobenzene)), 1,4-butanediol, were controlled by restriction of crystallization of polymer glycols. For the polyether glycol based-polyurethane elastomers (PUEs), poly(oxytetramethylene) glycol (PTMG), and PTMG incorporating dimethyl groups (PTG-X) and methyl side groups (PTG-L) were employed as a polymer glycol. For the PC-glycol, the randomly copolymerized PC-glycols with hexamethylene (C6) and tetramethylene (C4) units between carbonate groups with various composition ratios (C4/C6 = 0/100, 50/50, 70/30 and 90/10) were employed. The degree of microphase separation and mechanical properties of both the PUEs were investigated using differential scanning calorimetry, dynamic viscoelastic property measurements and tensile testing. Mechanical properties could be controlled by changing the molar ratio of two different monomer components. PMID:28883371

Fire and heat resistant laminating resins based on malemeido and citraconimido substituted 1 -2,4- and -2,6- diaminobenzenes

NASA Technical Reports Server (NTRS)

Mikroyannidis, John A.; Kourtides, Demetrius A. (Inventor)

1987-01-01

A novel class of fire and heat resistant bisimide resins prepared by thermal polymerization of maleimido or citraconimido substituted 1-(dialkox phosphonyl) methyl-2-4 and -2,6-diamino benzenes was presented. The polymer precursors are prepared by reacting 1-(diorgano oxyphosphonyl) methyl-2-4- and -2,6-diamino benzenes with maliec anhydride or citraconic anhydride in a mole ratio 1:2. Chain extension of the monomers is achieved by reacting the mono-N-maleimido derivaties of 1 (diorgano oxyphosphonyl) methyl -2,4- and -2,6-diamino benzenes with aryl tetracarboxylic dianhydrides, such as benzophenone tetracarboxylic dianhydride, or aryl diisocyanates, such as methylene bis(4-phenyl isocyanate), in a mole ratio 2:1. The polymerization of the monomers is studied by diferential scanning calorimetry and the thermal stability of the polymers is ascertained by thermogravimetric analysis.

Hydrocarbon polymeric binder for advanced solid propellant

NASA Technical Reports Server (NTRS)

Potts, J. E. (Editor)

1972-01-01

A series of DEAB initiated isoprene polymerizations were run in the 5-gallon stirred autoclave reactor. Polymerization run parameters such as initiator concentration and feed rate were correlated with the molecular weight to provide a basis for molecular weight control in future runs. Synthetic methods were developed for the preparation of n-1,3-alkadienes. By these methods, 1,3-nonadiene was polymerized using DEAB initiator to give an ester-telechelic polynonadiene. This was subsequently hydrogenated with copper chromite catalyst to give a hydroxyl terminated saturated liquid hydrocarbon prepolymer having greatly improved viscosity characteristics and a Tg 18 degrees lower than that of the hydrogenated polyisoprenes. The hydroxyl-telechelic saturated polymers prepared by the hydrogenolysis of ester-telechelic polyisoprene were reached with diisocyanates under conditions favoring linear chain extension gel permeation chromatography was used to monitor this condensation polymerization. Fractions having molecular weights above one million were produced.

Allergic contact dermatitis due to urethane acrylate in ultraviolet cured inks.

PubMed Central

Nethercott, J R; Jakubovic, H R; Pilger, C; Smith, J W

1983-01-01

Seven workers exposed to ultraviolet printing inks developed contact dermatitis. Six cases were allergic and one irritant. A urethane acrylate resin accounted for five cases of sensitisation, one of which was also sensitive to pentaerythritol triacrylate and another also to an epoxy acrylate resin. One instance of allergy to trimethylpropane triacrylate accounted for the sixth case of contact dermatitis in this group of workers. An irritant reaction is presumed to account for the dermatitis in the individual not proved to have cutaneous allergy by patch tests. In this instance trimethylpropane triacrylate was thought to be the most likely irritating agent. Laboratory investigation proved urethane acrylate to be an allergen. The results of investigations of the sensitisation potentials of urethane acrylate, methylmethacrylate, epoxy acrylate resins, toluene-2,4-diisocyanate, and other multifunctional acrylic monomers in the albino guinea pig are presented. The interpretation of such predictive tests is discussed. Images PMID:6223656

[Synthesis and characterization of polylactide-based thermosetting polyurethanes with shape memory properties].

PubMed

Shi, Shuo; Gu, Lin; Yang, Yihu; Yu, Haibin; Chen, Rui; Xiao, Xianglian; Qiu, Jun

2016-06-25

A series of bio-based thermosetting polyurethanes (Bio-PUs) were synthesized by the crosslinking reaction of polylactide and its copolymers diols with hexamethylene diisocyanate (HDI) trimer. The obtained Bio-PUs were characterized by Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimetry (DSC), Thermal Gravimetric Analysis (TGA), universal tensile testing machine and cytotoxicity test. Results indicate that the PLA copolymer (P(LA-co-CL)) diols reduced the glass transition temperature (Tg) of Bio-PUs and improved their thermal stability, compared with PLA diols. The Bio-PUs synthesized from P (LA-co-CL) diols exhibit better mechanical performance and shape memory properties. Especially, Young modulus and elongation at break of the obtained Bio-PUs were 277.7 MPa and 230% respectively; the shape recovery time of the obtained Bio-PUs at body temperature was only 93 s. Furthermore, alamar blue assay results showed that the obtained Bio-PUs had no cell toxicity.

Fast-responding bio-based shape memory thermoplastic polyurethanes

DOE PAGES

Petrovic, Zoran S.; Milic, Jelena; Zhang, Fan; ...

2017-05-31

Fast response shape-memory polyurethanes were prepared from bio-based polyols, diphenyl methane diisocyanate and butane diol. The bio-based polyester polyols were synthesized from 9-hydroxynonanoic acid, a product obtained by ozonolysis of fatty acids extracted from soy oil and castor oil. The morphology of polyurethanes was investigated by synchrotron ultra-small angle X-ray scattering, which revealed the inter-domain spacing between the hard and soft phases, the degree of phase separation, and the level of intermixing between the hard and soft phases. We also conducted thorough investigations of the thermal, mechanical, and dielectric properties of the polyurethanes, and found that high crystallization rate ofmore » the soft segment gives these polyurethanes unique properties suitable for shapememory applications, such as adjustable transition temperatures, high degree of elastic elongations, and good mechanical strength. In conclusion, these materials are also potentially biodegradable and biocompatible, therefore suitable for biomedical and environmental applications.« less

Preparation and properties of poly HTBN-based urethane-urea/organo reactive montmorillonite nanocomposites

NASA Astrophysics Data System (ADS)

Li, Zai-Feng; Wu, Yuan; Zhang, Fu-Tao; Cao, Yu-Yang; Wu, Shou-Peng; Wang, Ting

2012-12-01

With ultrasonic assistant mixing way, an intercalated mixture of polyol/organo reactive montmorillonite (ORMMT) was pretreated. The prepolymer composed MMT clay was prepared by reaction of polyol/ORMMT mixture with toluene diisocyanate (TDI). The resultant prepolymer reacted with extender (DMTDA) and then the polyurethane-urea/organo reactive montmorillonite (PUU/ORMMT) nanocomposites were obtained. The structure, morphology and properties of PUU/ORMMT nanocomposites were characterized by FT-IR, TEM, AFM, strain-stress machine, TGA, and dynamic mechanical analysis (DMA). The results showed that when the OMMT content is 3%, the PUU/ORMMT nanocomposities performed super mechanical properties. Because of the presence of ORMMT, both T g of the soft segment and tan δ of the PUU increased, and the decomposition temperature for the first step and the second step increased respectively. TEM images showed that the organophilic MMT particles in the PUU composite exhibit a high degree of intercalation and exfoliation.

Development of segmented polyurethane elastomers with low iodine content exhibiting radiopacity and blood compatibility.

PubMed

Dawlee, S; Jayabalan, Muthu

2011-10-01

Biofunctionally active and inherently radiopaque polymers are the emerging need for biomedical applications. Novel segmented polyurethane elastomer with inherent radiopacity was prepared using aliphatic chain extender 2,3-diiodo-2-butene-1,4-diol, polyol polytetramethylene glycol and 4,4'-methylenebis(phenyl isocyanate) (MDI) for blood compatible applications. Aliphatic polyurethane was also prepared using hexamethylene diisocyanate for comparison. X-ray analysis of the polyurethanes revealed good radiopacity even at a relatively low concentration of 3% iodine in aromatic polyurethane and 10% in aliphatic polyurethane. The polyurethanes also possessed excellent thermal stability. MDI-based polyurethane showed considerably higher tensile strength than the analogous HDI-based polyurethane. MDI-based aromatic polyurethane exhibited a dynamic surface morphology in aqueous medium, resulting in the segregation of hydrophilic domains which was more conducive to anti-thrombogenic properties. The polyurethane was cytocompatible with L929 fibroblast cells, non-hemolytic, and possessed good blood compatibility.

Fast-Responding Bio-Based Shape Memory Thermoplastic Polyurethanes.

PubMed

Petrović, Zoran S; Milić, Jelena; Zhang, Fan; Ilavsky, Jan

2017-07-14

Novel fast response shape-memory polyurethanes were prepared from bio-based polyols, diphenyl methane diisocyanate and butane diol for the first time. The bio-based polyester polyols were synthesized from 9-hydroxynonanoic acid, a product obtained by ozonolysis of fatty acids extracted from soy oil and castor oil. The morphology of polyurethanes was investigated by synchrotron ultra-small angle X-ray scattering, which revealed the inter-domain spacing between the hard and soft phases, the degree of phase separation, and the level of intermixing between the hard and soft phases. We also conducted thorough investigations of the thermal, mechanical, and dielectric properties of the polyurethanes, and found that high crystallization rate of the soft segment gives these polyurethanes unique properties suitable for shape-memory applications, such as adjustable transition temperatures, high degree of elastic elongations, and good mechanical strength. These materials are also potentially biodegradable and biocompatible, therefore suitable for biomedical and environmental applications.

The nature of the MDI/wood bond

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marcinko, J.J.; Phanopoulos, C.; Newman, W.H.

1995-12-01

Polymeric diphenylmethane diisocyanate (pMDI) binders have been used in the wood composite industry for 20 years. Almost one half of the oriented strand board (OSB) manufactures in North America are taking advantage of its processing speed and superior board performance. MDI`s current use in Strandboard, MDF (medium density fiber board), LVL (laminated veneer lumber), Plywood, and Particleboard is wide spread. A fundamental understanding of the role of MIDI as a binder in these complex composites is essential for further processing optimization. Experimental data is presented which investigates the nature of the chemical bonding in wood composites. Solid state nuclear magneticmore » resonance (NMR) data is combined with data from thermal analysis and fluorescence microscopy to investigate the chemistry, penetration, and morphology of the isocyanate/wood interphase. Structure property relationships are developed and related to composite performance. The study contrasts isocyanate and phenol formaldehyde binder systems.« less

[The research on the surfacial modification of organic high-performance Kevlar fiber].

PubMed

Zheng, Yu-ying; Fu, Ming-lian; Cai, Wei-long; Wang, Can-yao; Wang, Liang-en

2004-04-01

In the paper the authors tried to use chemical disposal to bring the activity mass onto the surface of Kevlar fiber with the purpose of surface graft modification. In the paper the authors used the FTIR spectra to discuss the graft of toluene-2, 4-diisocyanate onto Kevlar fiber. The authors studied and analysed the effect of hydrolytic time on the content of -O-H group of the production, and the effect of hydrolyzation and hexyl-lactam steadily disposing on the graft reaction. The result showed that the content of -O-H group increased after hydrolyzation, it's helpful for the graft reaction, and hexyl-lactam steadily disposing made the graf product more stable. Through the research the authors came to the conclusion that by bringing some activity masses onto the fiber surface the authors can improve the interface of fiber/resin effectively.

[Surface grafting modification and stabilization of Kevlar fiber].

PubMed

Zheng, Yu-ying; Fu, Ming-lian; Wang, Can-yao; Wang, Liang-en

2005-11-01

Chemical disposal was used to bring the activity group onto the surface of Kevlar fiber for the purpose of surface grafting modification. The interfacial constitution of the grafting of toluene-2,4-diisocyanate (TDI) onto Kevlar fiber was determined by Fourier transform infrared spectroscopy. In the mean time, hexyl-lactam stabilization and poly-glycol (400, PEG) stabilization on the grafted product were also studied. The effects of different nTDI:nPEG ratios on the production's interfacial constitution was analysed. It is concluded that the stabilization took place on the surface. The intensity of the bands relented at about 3300 cm(-1) and was reinforced at about 1700-1720 cm(-1) when the ratio of nTDI:nPEG = 1:3, but when the ratio is 1:1 and 1:2, the bands at about 3 300 and 1700-1720 cm(-1) are almost the same.

Mortality Among Workers Exposed to Toluene Diisocyanate in the US Polyurethane Foam Industry: Update and Exposure-Response Analyses

PubMed Central

Pinkerton, Lynne E.; Yiin, James H.; Daniels, Robert D.; Fent, Kenneth W.

2017-01-01

Background Mortality among 4,545 toluene diisocyante (TDI)-exposed workers was updated through 2011. The primary outcome of interest was lung cancer. Methods Life table analyses, including internal analyses by exposure duration and cumulative TDI exposure, were conducted. Results Compared with the US population, all cause and all cancer mortality was increased. Lung cancer mortality was increased but was not associated with exposure duration or cumulative TDI exposure. In post hoc analyses, lung cancer mortality was associated with employment duration in finishing jobs, but not in finishing jobs involving cutting polyurethane foam. Conclusions Dermal exposure, in contrast to inhalational exposure, to TDI is expected to be greater in finishing jobs and may play a role in the observed increase in lung cancer mortality. Limitations include the lack of smoking data, uncertainty in the exposure estimates, and exposure estimates that reflected inhalational exposure only. PMID:27346061

Chemoenzymatic Synthesis and Chemical Recycling of Poly(ester-urethane)s

PubMed Central

Hayashi, Hiroto; Yanagishita, Yoshio; Matsumura, Shuichi

2011-01-01

Novel poly(ester-urethane)s were prepared by a synthetic route using a lipase that avoids the use of hazardous diisocyanate. The urethane linkage was formed by the reaction of phenyl carbonate with amino acids and amino alcohols that produced urethane-containing diacids and hydroxy acids, respectively. The urethane diacid underwent polymerization with polyethylene glycol and α,ω-alkanediols and also the urethane-containing hydroxy acid monomer was polymerized by the lipase to produce high-molecular-weight poly(ester-urethane)s. The periodic introduction of ester linkages into the polyurethane chain by the lipase-catalyzed polymerization afforded chemically recyclable points. They were readily depolymerized in the presence of lipase into cyclic oligomers, which were readily repolymerized in the presence of the same enzyme. Due to the symmetrical structure of the polymers, poly(ester-urethane)s synthesized in this study showed higher Tm, Young’s modulus and tensile strength values. PMID:22016604

Cytotoxicity and mechanical behavior of chitin-bentonite clay based polyurethane bio-nanocomposites.

PubMed

Zia, Khalid Mahmood; Zuber, Mohammad; Barikani, Mehdi; Hussain, Rizwan; Jamil, Tahir; Anjum, Sohail

2011-12-01

Chitin based polyurethane bio-nanocomposites (PUBNC) were prepared using chitin, Delite HPS bentonite nanoclay enriched in montmorillonite (MMT), 4,4'-diphenylmethane diisocyanate (MDI) and polycaprolactone polyol CAPA 231 (3000 g/mol(-1)). The prepolymers having different concentration of Delite HPS bentonite nanoclay were extended with 2 moles of chitin. The structures of the resulted polymers were determined by FT-IR technique. The effect of nanoclay contents on mechanical properties and in vitro biocompatibility was investigated. The mechanical properties of the synthesized materials were improved with increase in the Delite HPS bentonite nanoclay contents. Optimum mechanical properties were obtained from the PU bio-nanocomposite samples having 4% Delite HPS bentonite nanoclay. The results revealed that the final PU bio-nanocomposite having 2% Delite HPS bentonite nanoclay contents is ideal contenders for surgical threads with on going investigations into their in vitro biocompatibility, non-toxicity, and mechanical properties. Copyright © 2011 Elsevier B.V. All rights reserved.

Isocyanate exposure and occupational asthma: a case-referent study

PubMed Central

Meredith, S; Bugler, J; Clark, R

2000-01-01

OBJECTIVE—To examine the quantitative relation between exposure to isocyanates and occupational asthma, and to explore the role of atopy and smoking in occurrence of the disease.
METHOD—A case-referent study was undertaken of cases from two manufacturing companies (A and B) from which referents without disease could be selected and reliable exposure measurements were available. In company A, 27 cases mainly attributed to toluene diisocyanate (TDI) were matched to 51 referents on work area, start and duration of employment, sex, and age. Exposures were estimated from existing measurements by job category. In company B there were seven cases attributed to 4,4'-diphenylmethane diisocyanate (MDI) in two areas of the plant; 12 non-cases from the same areas were used as referents. Personal exposure measurements were available for all cases and 11 referents.
RESULTS—No difference in peak exposures between cases and referents was found in either plant; but in both, time weighted average (TWA) exposures at the time of onset of asthma were higher for cases. In A, the mean TWA exposure for cases was 1.5 (95% confidence interval (95% CI) 1.2 to 1.8) ppb compared with 1.2 (1.0 to 1.4) ppb for referents. From a matched analysis, the odds ratio (OR) associated with 8 hour TWA exposure to isocyanates greater than 1.125 ppb (the median concentration for the referent group) was 3.2 (95% CI 0.96 to 10.6; p=0.06). Occupational asthma was associated with a pre-employment history of atopic illness (OR 3.5, p=0.04) and, less strongly, with smoking (OR 2.1, p=0.14). In B, small numbers limited analysis, but three of seven cases had at least one TWA exposure measurement greater than 5 ppb compared with one of 11 referents (OR 7.5, p=0.09).
CONCLUSION—Asthma can occur at low concentrations of isocyanates, but even at low concentrations, the higher the exposure the greater the risk. By contrast with other studies, smoking and atopy seemed to increase the odds of occupational asthma due to isocyanates, but did not affect the estimate of risk associated with exposure.


Keywords: occupational asthma; isocyanates PMID:11077012

Hexavalent chromium and isocyanate exposures during military aircraft painting under crossflow ventilation.

PubMed

Bennett, James S; Marlow, David A; Nourian, Fariba; Breay, James; Hammond, Duane

2016-01-01

Exposure control systems performance was investigated in an aircraft painting hangar. The ability of the ventilation system and respiratory protection program to limit worker exposures was examined through air sampling during painting of F/A-18C/D strike fighter aircraft, in four field surveys. Air velocities were measured across the supply filter, exhaust filter, and hangar midplane under crossflow ventilation. Air sampling conducted during painting process phases (wipe-down, primer spraying, and topcoat spraying) encompassed volatile organic compounds, total particulate matter, Cr[VI], metals, nitroethane, and hexamethylene diisocyanate, for two worker groups: sprayers and sprayer helpers ("hosemen"). One of six methyl ethyl ketone and two of six methyl isobutyl ketone samples exceeded the short term exposure limits of 300 and 75 ppm, with means 57 ppm and 63 ppm, respectively. All 12 Cr[VI] 8-hr time-weighted averages exceeded the recommended exposure limit of 1 µg/m3, 11 out of 12 exceeded the permissible exposure limit of 5 µg/m3, and 7 out of 12 exceeded the threshold limit value of 10 µg/m3, with means 38 µg/m3 for sprayers and 8.3 µg/m3 for hosemen. Hexamethylene diisocyanate means were 5.95 µg/m3 for sprayers and 0.645 µg/m3 for hosemen. Total reactive isocyanate group--the total of monomer and oligomer as NCO group mass--showed 6 of 15 personal samples exceeded the United Kingdom Health and Safety Executive workplace exposure limit of 20 µg/m3, with means 50.9 µg/m3 for sprayers and 7.29 µg/m3 for hosemen. Several exposure limits were exceeded, reinforcing continued use of personal protective equipment. The supply rate, 94.4 m3/s (200,000 cfm), produced a velocity of 8.58 m/s (157 fpm) at the supply filter, while the exhaust rate, 68.7 m3/s (146,000 cfm), drew 1.34 m/s (264 fpm) at the exhaust filter. Midway between supply and exhaust locations, the velocity was 0.528 m/s (104 fpm). Supply rate exceeding exhaust rate created re-circulations, turbulence, and fugitive emissions, while wasting energy. Smoke releases showing more effective ventilation here than in other aircraft painting facilities carries technical feasibility relevance.

Hexavalent Chromium and Isocyanate Exposures during Military Aircraft Painting under Crossflow Ventilation

PubMed Central

Bennett, James S.; Marlow, David A.; Nourian, Fariba; Breay, James; Hammond, Duane

2016-01-01

Exposure control systems performance was investigated in an aircraft painting hangar. The ability of the ventilation system and respiratory protection program to limit worker exposures was examined through air sampling during painting of F/A-18C/D strike fighter aircraft, in four field surveys. Air velocities were measured across the supply filter, exhaust filter, and hangar midplane under crossflow ventilation. Air sampling conducted during painting process phases (wipe-down, primer spraying, and topcoat spraying) encompassed volatile organic compounds, total particulate matter, Cr[VI], metals, nitroethane, and hexamethylene diisocyanate, for two worker groups: sprayers and sprayer helpers (“hosemen”). One of six methyl ethyl ketone and two of six methyl isobutyl ketone samples exceeded the short term exposure limits of 300 and 75 ppm, with means 57 ppm and 63 ppm, respectively. All 12 Cr[VI] 8-hr time-weighted averages exceeded the recommended exposure limit of 1 µg/m3, 11 out of 12 exceeded the permissible exposure limit of 5 µg/m3, and 7 out of 12 exceeded the threshold limit value of 10 µg/m3, with means 38 µg/m3 for sprayers and 8.3 µg/m3 for hosemen. Hexamethylene diisocyanate means were 5.95 µg/m3 for sprayers and 0.645 µg/m3 for hosemen. Total reactive isocyanate group—the total of monomer and oligomer as NCO group mass—showed six of 15 personal samples exceeded the United Kingdom Health and Safety Executive workplace exposure limit of 20 µg/m3, with means 50.9 µg/m3 for sprayers and 7.29 µg/m3 for hosemen. Several exposure limits were exceeded, reinforcing continued use of personal protective equipment. The supply rate, 94.4 m3/s (200,000 cfm), produced a velocity of 8.58 m/s (157 fpm) at the supply filter, while the exhaust rate, 68.7 m3/s (146,000 cfm), drew 1.34 m/s (264 fpm) at the exhaust filter. Midway between supply and exhaust locations, the velocity was 0.528 m/s (104 fpm). Supply rate exceeding exhaust rate created re-circulations, turbulence, and fugitive emissions, while wasting energy. Smoke releases showing more effective ventilation here than in other aircraft painting facilities carries technical feasibility relevance. PMID:26698920

Association of respiratory symptoms and asthma with occupational exposures: findings from a population-based cross-sectional survey in Telemark, Norway.

PubMed

Abrahamsen, R; Fell, A K M; Svendsen, M V; Andersson, E; Torén, K; Henneberger, P K; Kongerud, J

2017-03-22

The aim of this study was to estimate the prevalence of respiratory symptoms and physician-diagnosed asthma and assess the impact of current occupational exposure. Cross-sectional analyses of the prevalence of self-reported respiratory health and association with current occupational exposure in a random sample of the general population in Telemark County, Norway. In 2013, a self-administered questionnaire was mailed to a random sample of the general population, aged 16-50, in Telemark, Norway. The overall response rate was 33%, comprising 16 099 responders. The prevalence for respiratory symptoms and asthma, and OR of respiratory symptoms and asthma for occupational groups and exposures were calculated. Occupational exposures were assessed using self-reported exposure and an asthma-specific job-exposure matrix (JEM). The prevalence of physician-diagnosed asthma was 11.5%. For the occupational groups, the category with agriculture/fishery workers and craft/related trade workers was associated with wheezing and asthma attack in the past 12 months, showing OR 1.3 (1.1 to 1.6) and 1.9 (1.2 to 2.8), respectively. The group including technicians and associated professionals was also associated with wheezing OR 1.2 (1.0 to 1.3) and asthma attack OR 1.4 (1.1 to 1.9). The JEM data show that exposure to flour was associated with wheezing OR 3.2 (1.4 to 7.3) and woken with dyspnoea OR 3.5 (1.3 to 9.5), whereas exposures to diisocyanates, welding/soldering fumes and exposure to vehicle/motor exhaust were associated with dyspnoea OR 2.9 (1.5 to 5.7), 3.2 (1.6 to 6.4) and 1.4 (1.0 to 1.8), respectively. The observed prevalence of physician-diagnosed asthma was 11.5%. The 'manual' occupations were associated with respiratory symptoms. Occupational exposure to flour, diisocyanates, welding/soldering fumes and vehicle/motor exhaust was associated with respiratory symptoms in the past 12 months and use of asthma medication. However, prospective data are needed to confirm the observed associations. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Thermal properties of poly(urethane-ester-siloxane)s based on hyperbranched polyester

NASA Astrophysics Data System (ADS)

Pergal, M. V.; Džunuzović, J. V.; Kićanović, M.; Vodnik, V.; Pergal, M. M.; Jovanović, S.

2011-12-01

Novel polyurethanes (PUs) were synthesized using hydroxy-terminated hyperbranched polyester (BH-20) and 4,4'-methylenediphenyl diisocyanate (MDI) as hard segments and hydroxy-terminated ethylene oxide-poly(dimethylsiloxane)-ethylene oxide triblock copolymer (PDMS-EO) as soft segment, with soft segment content ranging from 30 to 60 wt %. The PUs were synthesized by two-step solution polymerization method. The influence of the soft segment content on the structure, swelling behavior and thermal properties of PUs was investigated. According to the results obtained by swelling measurements, the increase of the hard segment content resulted in the increase of the crosslinking density of synthesized samples. DSC results showed that the glass transition temperatures increase from 36 to 65°C with increasing hard segment content. It was demonstrated using thermogravimetric analysis (TGA) that thermal stability of investigated PUs increases with increase of the soft PDMS-EO content. This was concluded from the temperatures corresponding to the 10 wt % loss, which represents the beginning of thermal degradation of samples.

Enzymatic tranformations of lignin. Annual report 1 July 1980-30 June 1981

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glasser, W.G.; Hall, P.L.

1981-06-01

Research is summarized on biological approaches to the utilization of lignin degradation to raw material for the manufacture of chemicals and materials. This investigation studied the possible involvement of reduced oxygen species produced by the white-rot fungus, C. versicolor, in the initial breakdown of the lignin macromolecule during its biodegradation. This fungus was shown to be capable of exporting superoxide radical. While the degree to which this organism was responsible for actual lignin degradation is not clear, there were indications that a correlation may exist between the concentration of extracellular superoxide radical in the medium and the extent of ligninmore » degradation. Two different fermentation schemes were compared and several control fermentation experiments were made. Research dealing with improvements in lignin structure analysis, liquefaction of lignin preparations by reaction with propylene oxide, and solidification of liquified kraft lignin by crosslinking with diisocyanate compounds was explored. The use of scanning electron microscopy for revealing interaction between fiber and binder is noted.« less

Fabrication of chemically cross-linked porous gelatin matrices.

PubMed

Bozzini, Sabrina; Petrini, Paola; Altomare, Lina; Tanzi, Maria Cristina

2009-01-01

The aim of this study was to chemically cross-link gelatin, by reacting its free amino groups with an aliphatic diisocyanate. To produce hydrogels with controllable properties, the number of reacting amino groups was carefully determined. Porosity was introduced into the gelatin-based hydrogels through the lyophilization process. Porous and non-porous matrices were characterized with respect to their chemical structure, morphology, water uptake and mechanical properties. The physical, chemical and mechanical properties of the porous matrices are related to the extent of their cross-linking, showing that they can be controlled by varying the reaction parameters. Water uptake values (24 hours) vary between 160% and 200% as the degree of cross-linking increases. The flexibility of the samples also decreases by changing the extent of cross-linking. Young's modulus shows values between 0.188 KPa, for the highest degree, and 0.142 KPa for the lowest degree. The matrices are potential candidates for use as tissue-engineering scaffolds by modulating their physical chemical properties according to the specific application.

Isopropyl Myristate-Modified Polyether-Urethane Coatings as Protective Barriers for Implantable Medical Devices

PubMed Central

Roohpour, Nima; Wasikiewicz, Jaroslaw M.; Moshaverinia, Alireza; Paul, Deepen; Rehman, Ihtesham U.; Vadgama, Pankaj

2009-01-01

Polyurethane films have potential applications in medicine, especially for packaging implantable medical devices. Although polyether-urethanes have superior mechanical properties and are biocompatible, achieving water resistance is still a challenge. Polyether based polyurethanes with two different molecular weights (PTMO1000, PTMO2000) were prepared from 4,4’-diphenylmethane diisocyanate and poly(tetra-methylene oxide). Polymer films were introduced using different concentrations (0.5-10 wt %) of isopropyl myristate lipid (IPM) as a non-toxic modifying agent. The physical and mechanical properties of these polymers were characterised using physical and spectroscopy techniques (FTIR, Raman, DSC, DMA, tensile testing). Water contact angle and water uptake of the membranes as a function of IPM concentration was also determined accordingly. The FTIR and Raman data indicate that IPM is dispersed in polyurethane at ≤ 2wt% and thermal analysis confirmed this miscibility to be dependent on soft segment length. Modified polymers showed increased tensile strength and failure strain as well as reduced water uptake by up to 24% at 1-2 wt% IPM.

X-ray computed tomography of wood-adhesive bondlines: Attenuation and phase-contrast effects

DOE PAGES

Paris, Jesse L.; Kamke, Frederick A.; Xiao, Xianghui

2015-07-29

Microscale X-ray computed tomography (XCT) is discussed as a technique for identifying 3D adhesive distribution in wood-adhesive bondlines. Visualization and material segmentation of the adhesives from the surrounding cellular structures require sufficient gray-scale contrast in the reconstructed XCT data. Commercial wood-adhesive polymers have similar chemical characteristics and density to wood cell wall polymers and therefore do not provide good XCT attenuation contrast in their native form. Here, three different adhesive types, namely phenol formaldehyde, polymeric diphenylmethane diisocyanate, and a hybrid polyvinyl acetate, are tagged with iodine such that they yield sufficient X-ray attenuation contrast. However, phase-contrast effects at material edgesmore » complicate image quality and segmentation in XCT data reconstructed with conventional filtered backprojection absorption contrast algorithms. A quantitative phase retrieval algorithm, which isolates and removes the phase-contrast effect, was demonstrated. The paper discusses and illustrates the balance between material X-ray attenuation and phase-contrast effects in all quantitative XCT analyses of wood-adhesive bondlines.« less

Synthesis and Characterization of Biodegradable Polyurethane for Hypopharyngeal Tissue Engineering

PubMed Central

Shen, Zhisen; Lu, Dakai; Li, Qun; Zhang, Zongyong

2015-01-01

Biodegradable crosslinked polyurethane (cPU) was synthesized using polyethylene glycol (PEG), L-lactide (L-LA), and hexamethylene diisocyanate (HDI), with iron acetylacetonate (Fe(acac)3) as the catalyst and PEG as the extender. Chemical components of the obtained polymers were characterized by FTIR spectroscopy, 1H NMR spectra, and Gel Permeation Chromatography (GPC). The thermodynamic properties, mechanical behaviors, surface hydrophilicity, degradability, and cytotoxicity were tested via differential scanning calorimetry (DSC), tensile tests, contact angle measurements, and cell culture. The results show that the synthesized cPU possessed good flexibility with quite low glass transition temperature (T g, −22°C) and good wettability. Water uptake measured as high as 229.7 ± 18.7%. These properties make cPU a good candidate material for engineering soft tissues such as the hypopharynx. In vitro and in vivo tests showed that cPU has the ability to support the growth of human hypopharyngeal fibroblasts and angiogenesis was observed around cPU after it was implanted subcutaneously in SD rats. PMID:25839041

X-ray computed tomography of wood-adhesive bondlines: Attenuation and phase-contrast effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paris, Jesse L.; Kamke, Frederick A.; Xiao, Xianghui

Microscale X-ray computed tomography (XCT) is discussed as a technique for identifying 3D adhesive distribution in wood-adhesive bondlines. Visualization and material segmentation of the adhesives from the surrounding cellular structures require sufficient gray-scale contrast in the reconstructed XCT data. Commercial wood-adhesive polymers have similar chemical characteristics and density to wood cell wall polymers and therefore do not provide good XCT attenuation contrast in their native form. Here, three different adhesive types, namely phenol formaldehyde, polymeric diphenylmethane diisocyanate, and a hybrid polyvinyl acetate, are tagged with iodine such that they yield sufficient X-ray attenuation contrast. However, phase-contrast effects at material edgesmore » complicate image quality and segmentation in XCT data reconstructed with conventional filtered backprojection absorption contrast algorithms. A quantitative phase retrieval algorithm, which isolates and removes the phase-contrast effect, was demonstrated. The paper discusses and illustrates the balance between material X-ray attenuation and phase-contrast effects in all quantitative XCT analyses of wood-adhesive bondlines.« less

Porous Cross-Linked Polyimide-Urea Networks

NASA Technical Reports Server (NTRS)

Meador, Mary Ann B. (Inventor); Nguyen, Baochau N. (Inventor)

2015-01-01

Porous cross-linked polyimide-urea networks are provided. The networks comprise a subunit comprising two anhydride end-capped polyamic acid oligomers in direct connection via a urea linkage. The oligomers (a) each comprise a repeating unit of a dianhydride and a diamine and a terminal anhydride group and (b) are formulated with 2 to 15 of the repeating units. The subunit was formed by reaction of the diamine and a diisocyanate to form a diamine-urea linkage-diamine group, followed by reaction of the diamine-urea linkage-diamine group with the dianhydride and the diamine to form the subunit. The subunit has been cross-linked via a cross-linking agent, comprising three or more amine groups, at a balanced stoichiometry of the amine groups to the terminal anhydride groups. The subunit has been chemically imidized to yield the porous cross-linked polyimide-urea network. Also provided are wet gels, aerogels, and thin films comprising the networks, and methods of making the networks.

Bio-based polyurethane for tissue engineering applications: How hydroxyapatite nanoparticles influence the structure, thermal and biological behavior of polyurethane composites.

PubMed

Gabriel, Laís P; Santos, Maria Elizabeth M Dos; Jardini, André L; Bastos, Gilmara N T; Dias, Carmen G B T; Webster, Thomas J; Maciel Filho, Rubens

2017-01-01

In this work, thermoset polyurethane composites were prepared by the addition of hydroxyapatite nanoparticles using the reactants polyol polyether and an aliphatic diisocyanate. The polyol employed in this study was extracted from the Euterpe oleracea Mart. seeds from the Amazon Region of Brazil. The influence of hydroxyapatite nanoparticles on the structure and morphology of the composites was studied using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), the structure was evaluated by Fourier transform infrared spectroscopy (FT-IR), thermal properties were analyzed by thermogravimetry analysis (TGA), and biological properties were studied by in vitro and in vivo studies. It was found that the addition of HA nanoparticles promoted fibroblast adhesion while in vivo investigations with histology confirmed that the composites promoted connective tissue adherence and did not induce inflammation. In this manner, this study supports the further investigation of bio-based, polyurethane/hydroxyapatite composites as biocompatible scaffolds for numerous tissue engineering applications. Copyright © 2016 Elsevier Inc. All rights reserved.

Hydrogels of poly(ethylene glycol): mechanical characterization and release of a model drug.

PubMed

Iza, M; Stoianovici, G; Viora, L; Grossiord, J L; Couarraze, G

1998-03-02

Thermosensitive polymer networks were synthesized from poly(ethylene glycol), hexamethylene diisocyanate and 1,2,6-hexanetriol in stoichiometric proportions. By varying the amount of 1,2,6-hexanetriol and the molar mass of the poly(ethylene glycol), a wide range of networks with different crosslinking densities was prepared. The networks obtained were characterized by the temperature dependence of their degree of equilibrium swelling in water and by their Young's moduli. For each network, the molecular weight between crosslinks was estimated. The structure of the hydrogels was analysed with respect to scaling laws, and it was found that the results obtained with PEG 1500 and PEG 6000 hydrogels are in agreement with theoretical predictions, whereas those obtained with PEG 400 hydrogels are in disagreement. The release properties of PEG hydrogels were studied by the determination of the diffusion coefficient for acebutolol chlorhydrate and by an analysis of the effect of temperature on these coefficients. Finally, these release properties were correlated with the swelling and structural properties of the hydrogels.

Preparation and properties of adjacency crosslinked polyurethane-urea elastomers

NASA Astrophysics Data System (ADS)

Wu, Yuan; Cao, Yu-Yang; Wu, Shou-Peng; Li, Zai-Feng

2012-12-01

Adjacency crosslinked polyurethane-urea (PUU) elastomers with different crosslinking density were prepared by using hydroxyl-terminated liquid butadiene-nitrile (HTBN), toluene diisocyanate (TDI) and chain extender 3,5-dimethyl thio-toluene diamine (DMTDA) as raw materials, dicumyl peroxide (DCP) as initiator, and N,N'-m-phenylene dimaleimide (HVA-2) as the crosslinking agent. The influences of the crosslinking density and temperature on the structure and properties of such elastomers were investigated. The crosslinking density of PUU elastomer was tested by the NMR method. It is found that when the content of HVA-2 is 1.5%, the mechanical properties of polyurethane elastomer achieve optimal performance. By testing thermal performance of PUU, compared with linear PUU, the thermal stability of the elastomers has a marked improvement. With the addition of HVA-2, the loss factor tan δ decreases. FT-IR spectral studies of PUU elastomer at various temperatures were performed. From this study, heat-resistance polyurethane could be prepared, and the properties of PUU at high temperature could be improved obviously.

Sub-Surface and Bulk Creep Behaviour of Polyurethane/Clay Nanocomposites.

PubMed

Jin, J; Yusoh, K; Zhang, H X; Song, M

2016-03-01

A series of exfoliated and intercalated polyurethane organoclay nanocomposites were prepared by in situ polymerization of polyol/organoclay mixture, chain extender and diisocyanate. The creep behaviour of subsurface and bulk of the polyurethane coatings was investigated by nanoindentation technique and uniaxial conventional creep testing method, respectively. The results showed that the creep resistance of the nanocomposites was significantly improved by incorporation of organoclay. The enhancement of creep resistance was dependent on clay content as well as organoclay structure (exfoliation or intercalation) in the polymer matrix. With 1 wt% organoclay, the creep resistance increased by about 50% for the intercalated organoclay and 6% for the exfoliated organoclay systems, respectively, compared to the pristine polyurethane. Viscoelastic model was employed to investigate the effect of organoclay loadings on the creep performance of the polyurethane. Results showed the model was in good agreement with the experimental data. Incorporation of clay leads to an increase in elastic deformation especially in exfoliated polyurethane nanocomposites and induces a higher initial displacement at the early stage of creep.

Facile preparation of mussel-inspired polyurethane hydrogel and its rapid curing behavior.

PubMed

Sun, Peiyu; Wang, Jing; Yao, Xiong; Peng, Ying; Tu, Xiaoxiong; Du, Pengfei; Zheng, Zhen; Wang, Xinling

2014-08-13

A facile method was found to incorporate a mussel-inspired adhesive moiety into synthetic polymers, and mussel mimetic polyurethanes were developed as adhesive hydrogels. In these polymers, a urethane backbone was substituted for the polyamide chain of mussel adhesive proteins, and dopamine was appended to mimic the adhesive moiety of adhesive proteins. A series of mussel mimetic polyurethanes were created through a step-growth polymerization based on hexamethylene diisocyanate as a hard segment, PEG having different molecular weights as a soft segment, and lysine-dopamine as a chain extender. Upon a treatment with Fe(3+), the aqueous mussel mimetic polyurethane solutions can be triggered by pH adjustment to form adhesive hydrogels instantaneously; these materials can be used as injectable adhesive hydrogels. Upon a treatment with NaIO4, the mussel mimetic polyurethane solutions can be cured in a controllable period of time. The successful combination of the unique mussel-inspired adhesive moiety with a tunable polyurethane structure can result in a new kind of mussel-inspired adhesive polymers.

Facile preparation of antibacterial, highly elastic silvered polyurethane nanofiber fabrics using silver carbamate and their dermal wound healing properties.

PubMed

Hong, Suk-Min; Kim, Jong-Wan; Knowles, Jonathan C; Gong, Myoung-Seon

2017-02-01

In this study, polycarbonate diol/isosorbide-based antibacterial polyurethane nanofiber fabrics containing Ag nanoparticles were prepared by electrospinning process. Bio-based highly elastic polyurethane was prepared from hexamethylene diisocyanate and isosorbide/polycarbonate diol (8/2) by a simple one-shot bulk polymerization. Ag nanoparticles were formed using simple thermal reduction of silver 2-ethylhexylcarbamate at 120℃. The structural and morphological properties of polyurethane/Ag nanofibers were characterized by X-ray diffraction and scanning electron microscopy. The polyurethane nanofiber fabrics were flexible, with breaking strains from 355% to 950% under 7.28 to 23.1 MPa tensile stress. The antibacterial effects of the treated polyurethane/Ag fabrics against Staphylococcus aureus and methicillin resistant Staphylococcus aureus were examined and found to be excellent. Cell proliferation using the immortalized human keratinocyte HaCaT cell line was performed in order to determine cell viability in the presence of polyurethane and polyurethane/Ag fabrics, showing cytocompatiblility and a lack of toxicity.

Development of a flameproof elastic elastomeric fiber

NASA Technical Reports Server (NTRS)

Howarth, J. T.; Nilgrom, J.; Massucco, A.; Sheth, S. G.; Dawn, F. S.

1971-01-01

Various flexible polyurethane structures containing halogen were synthesized from polyesters derived from aliphatic or aromatic polyols and dibasic acids. Aliphatic halide structures could not be used because they are unstable at the required reaction temperatures, giving of hydrogen halide which hydrolyzes the ester linkages. In contract, halogen-containing aromatic polyols were stable and satisfactory products were made. The most promising composition, a brominated neopentyl glycol capped with toluene disocyanate, was used as a conventional diisocyanate, in conjunction with hydroxy-terminated polyethers or polyesters to form elastomeric urethanes containing about 10% bromine with weight. Products made in this manner will not burn in air, have an oxygen index value of about 25, and have tensile strength values of about 5,000 psi at 450% elongation. The most efficient additives for imparting flame retardancy to Spandex urethanes are aromatic halides and the most effective of these are the bromide compounds. Various levels of flame retardancy have been achieved depending on the levels of additives used.

Evaluation on biocompatibility of biomedical polyurethanes with different hard segment contents

NASA Astrophysics Data System (ADS)

Ma, Dai-Wei; Zhu, Rong; Wang, Yi-Yu; Zhang, Zong-Rui; Wang, Xin-Yu

2015-12-01

In this paper, polyurethane (PU) materials with different contents of hard segment (20%, 25%, 30%) were prepared based on hexamethylene diisocyanate and polycarbonate diols by solution polymerization. The obtained polycarbonate-urethane (PCU) elastomers were characterized by very good hydrophobic property and excellent resistance to hydrolysis. Hemolysis, recalification time and platelet-rich plasma adhesion were used to evaluate the blood compatibility of the materials. L929 cells cultured with leach liquor of these PU membranes were selected to perform the cytotoxicity experiments. The results indicate that the hemolysis rates of PU membranes are all less than 5%, which can meet the requirement of the national standards for biomaterials. However, compared with 20% and 30% groups, the recalification time of the sample containing 25% hard segment is longer, while the number of platelet adhesion is less. Additionally, cells cultured in the leach liquor of PU membranes with 25% hard segment proliferated relatively more thriving, meaning that this proportion of the material has the lowest cytotoxicity.

Thermal and mechanical properties of reduced graphene oxide/polyurethane nanocomposite.

PubMed

Pokharel, Pashupati; Lee, Dai Soo

2014-08-01

Reduced graphene oxide (RGO) based polyurethane (PU) nanocomposites have been successfully prepared without using solvent by in-situ polymerization. RGO was derived from microwave (MW) irradiation of graphite oxide (GO) powder prepared by a modified Hummer's method. A minimum amount of poly(tetramethylene glycol) (PTMEG) was added during the dispersion of RGO in a solvent to stabilize the graphene sheets and to prevent RGO from the restacking after the removal of the solvent. After the reaction of RGO with 4,4'-diphenylmethane diisocyanate (MDI), we obtained the concentrate of RGO in MDI with a minimum amount of PTMEG. Our method facilitated the fine dispersion of RGO in PU elastomers and improved the interfacial strength between RGO and PU. With the incorporation of 2.0 wt% of RGO, the tensile strength and Young's modulus of the PU nanocomposites increased by 30% and 50%, respectively without sacrificing the elongation at break. It was found that the crystalline portion of hard segments of the PU was lowered by the RGO in the nanocomposites.

Superfund Record of Decision (EPA Region 5): Fields Brook sediment operable unit, Ashtabula, Ohio, September 1986. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1986-09-30

Fields Brook is located in the City of Ashtabula, Ohio and drains a 5.6-square mile watershed (defined as the 'site'). The 3.5 mile main channel of Fields Brook flows through an industrial area that is one of the largest and most diversified concentrations of chemical plants in Ohio. Industrial sources have contaminated the sediment in Fields Brook with a variety of organic and heavy metal pollutants, including TCE, PCE, chlorobenzene, vinyl chloride, arsenic, zinc, mercury and chromium. Base-neutral compounds including hexachloroethane, toluenediamine and toluene diisocyanate also were detected in Fields Brook sediments. Sediments taken from the Ashtabula River in themore » vicinity of Fields Brook are contaminated with PCBs. The U.S. EPA believes that the amount of contamination entering the brook at this time has been substantially reduced due to the recent development of pollution control laws and discharge-permitting requirements.« less

Synthesis and Anticoagulant Activity of Polyureas Containing Sulfated Carbohydrates

PubMed Central

2015-01-01

Polyurea-based synthetic glycopolymers containing sulfated glucose, mannose, glucosamine, or lactose as pendant groups have been synthesized by step-growth polymerization of hexamethylene diisocyanate and corresponding secondary diamines. The obtained polymers were characterized by gel permeation chromatography, nuclear magnetic resonance spectroscopy, and Fourier transform infrared spectroscopy. The nonsulfated polymers showed similar results to the commercially available biomaterial polyurethane TECOFLEX in a platelet adhesion assay. The average degree of sulfation after reaction with SO3 was calculated from elemental analysis and found to be between three and four −OSO3 groups per saccharide. The blood-compatibility of the synthetic polymers was measured using activated partial thromboplastin time, prothrombin time, thrombin time, anti-IIa, and anti-Xa assays. Activated partial thromboplastin time, prothrombin time, and thrombin time results indicated that the mannose and lactose based polymers had the highest anticoagulant activities among all the sulfated polymers. The mechanism of action of the polymers appears to be mediated via an anti-IIa pathway rather than an anti-Xa pathway. PMID:25329742

Determination of airborne, volatile amines from polyurethane foams by sorption onto a high-capacity cation-exchange resin based on poly(succinic acid).

PubMed

Seeber, G; Buchmeiser, M R; Bonn, G K; Bertsch, T

1998-06-05

A high-capacity carboxylic acid-functionalized resin prepared by ring-opening metathesis polymerization based on cross-linked endo,endo-poly(norborn-2-ene-5,6-dicarboxylic acid) was used for the sampling of volatile, airborne amines from polyurethane (PU) foams. Six tertiary amines which represent commonly used promotors for the formation of PUs from diisocyanates and polyols, namely pentamethyldiethylenetriamine, diazabicyclooctane, N-methylmorpholine, N-ethylmorphine, 1,4-dimethylpiperazine and N,N-dimethylethanolamine, were sorbed onto the new resin. The sorption behavior of the new material was investigated in terms of loading capacities, the influence of concentration, flow-rate as well as of the amount of resin. Breakthrough curves were recorded from each single component as well as of mixtures thereof. Finally, the resin was used for the sampling of amines evaporating from PU foams applied in buildings. Further information about time dependent concentration profiles were obtained using a combination of GC-MS and Fourier transform IR spectroscopy.

Synthesis and characterization of biodegradable polyurethane for hypopharyngeal tissue engineering.

PubMed

Shen, Zhisen; Lu, Dakai; Li, Qun; Zhang, Zongyong; Zhu, Yabin

2015-01-01

Biodegradable crosslinked polyurethane (cPU) was synthesized using polyethylene glycol (PEG), L-lactide (L-LA), and hexamethylene diisocyanate (HDI), with iron acetylacetonate (Fe(acac)3) as the catalyst and PEG as the extender. Chemical components of the obtained polymers were characterized by FTIR spectroscopy, (1)H NMR spectra, and Gel Permeation Chromatography (GPC). The thermodynamic properties, mechanical behaviors, surface hydrophilicity, degradability, and cytotoxicity were tested via differential scanning calorimetry (DSC), tensile tests, contact angle measurements, and cell culture. The results show that the synthesized cPU possessed good flexibility with quite low glass transition temperature (T g , -22°C) and good wettability. Water uptake measured as high as 229.7 ± 18.7%. These properties make cPU a good candidate material for engineering soft tissues such as the hypopharynx. In vitro and in vivo tests showed that cPU has the ability to support the growth of human hypopharyngeal fibroblasts and angiogenesis was observed around cPU after it was implanted subcutaneously in SD rats.

[Research on the modification of Kevlar fiber by polypropylene glycol and cis-2-butene-1,4-diol].

PubMed

Zheng, Yu-ying; Wang, Can-yao; Fu, Ming-lian; Cai, Wei-long; Wang, Liang-en

2005-03-01

The mechanism of the modification of Kevlar fiber by polypropylene glycol(PPG) and cis-2-butene-1, 4-diol was studied in the paper, the authors learned the esterification of toluene-2, 4-diisocyanate (TDI) onto Kevlar fiber by infrared spectrum. In the mean time, the infrared spectrograms of the productions which steadily disposed by PPG and butendiol were analysed respectively, the result showed that the intensity of the bands was reinforced at about 1700-1720 cm(-1) after the samples were steadily disposed, that is to say, the group of --NCO has been stabilized into --NHCO group, the effect of steady disposal was obvious; but the disposal effect of butendiol was apparently better than PPG's at the same condition. Finally, the authors compared the influence of different mol rates between TDI and butendiol on the productions. Based onthe consequence, excessive butendiol would prevent the Kevlar fiber from farther reaction, therefore, the mol rate between TDI and butendiol should approach 1:1.

Injectable Biodegradable Polyurethane Scaffolds with Release of Platelet-derived Growth Factor for Tissue Repair and Regeneration

PubMed Central

Hafeman, Andrea E.; Li, Bing; Yoshii, Toshitaka; Zienkiewicz, Katarzyna; Davidson, Jeffrey M.; Guelcher, Scott A.

2013-01-01

Purpose The purpose of this work was to investigate the effects of triisocyanate composition on the biological and mechanical properties of biodegradable, injectable polyurethane scaffolds for bone and soft tissue engineering. Methods Scaffolds were synthesized using reactive liquid molding techniques, and were characterized in vivo in a rat subcutaneous model. Porosity, dynamic mechanical properties, degradation rate, and release of growth factors were also measured. Results Polyurethane scaffolds were elastomers with tunable damping properties and degradation rates, and they supported cellular infiltration and generation of new tissue. The scaffolds showed a two-stage release profile of platelet-derived growth factor, characterized by a 75% burst release within the first 24 h and slower release thereafter. Conclusions Biodegradable polyurethanes synthesized from triisocyanates exhibited tunable and superior mechanical properties compared to materials synthesized from lysine diisocyanates. Due to their injectability, biocompatibility, tunable degradation, and potential for release of growth factors, these materials are potentially promising therapies for tissue engineering. PMID:18516665

Mechanical properties of palm oil based bio-polyurethane foam of free rise and various densities

NASA Astrophysics Data System (ADS)

Hilmi, Hazmi; Zainuddin, Firuz; Cheng, Teoh Siew; Lan, Du Ngoc Uy

2017-12-01

Bio-foam was produced from palm oil-based polyol (POBP) and methylene diphenyl diisocyanate (MDI) with weight ratio of 1:1. The effect of opened mould (as free rise) and closed mould (control expansion) was investigated. Different densities of bio-polyurethane foam (0.3, 0.4 and 0.5 g.cm-3) were prepared using the closed mould system. The effect of density on morphology and compressive properties of bio-foam was studied. Results showed that bio-foam prepared by closed mould method possessed homogeneous cell structure and cell size compared to bio-foam prepared by opened mould. In addition, bio-foam using closed mould system had higher compression strength (0.47 MPa) than that of bio-foam using opened mould system (0.13 MPa). With higher density and lesser porosity, the compressive modulus and compressive strength of bio foams will be higher. The increase in compressive properties is due to the decrease in the cells size, more homogeneous cell structure and reduction in porosity content.

Manufacturing of biodegradable polyurethane scaffolds based on polycaprolactone using a phase separation method: physical properties and in vitro assay

PubMed Central

Asefnejad, Azadeh; Khorasani, Mohammad Taghi; Behnamghader, Aliasghar; Farsadzadeh, Babak; Bonakdar, Shahin

2011-01-01

Background Biodegradable polyurethanes have found widespread use in soft tissue engineering due to their suitable mechanical properties and biocompatibility. Methods In this study, polyurethane samples were synthesized from polycaprolactone, hexamethylene diisocyanate, and a copolymer of 1,4-butanediol as a chain extender. Polyurethane scaffolds were fabricated by a combination of liquid–liquid phase separation and salt leaching techniques. The effect of the NCO:OH ratio on porosity content and pore morphology was investigated. Results Scanning electron micrographs demonstrated that the scaffolds had a regular distribution of interconnected pores, with pore diameters of 50–300 μm, and porosities of 64%–83%. It was observed that, by increasing the NCO:OH ratio, the average pore size, compressive strength, and compressive modulus increased. L929 fibroblast and chondrocytes were cultured on the scaffolds, and all samples exhibited suitable cell attachment and growth, with a high level of biocompatibility. Conclusion These biodegradable polyurethane scaffolds demonstrate potential for soft tissue engineering applications. PMID:22072874

Sensitization to reactive diluents and hardeners in epoxy resin systems. IVDK data 2002-2011. Part I: reaction frequencies.

PubMed

Geier, Johannes; Lessmann, Holger; Hillen, Uwe; Skudlik, Christoph; Jappe, Uta

2016-02-01

Epoxy resin systems (ERSs), consisting of resins, reactive diluents, and hardeners, are indispensable in many branches of industry. In order to develop less sensitizing ERS formulations, knowledge of the sensitizing properties of single components is mandatory. To analyse the frequency of sensitization in the patients concerned, as one integral part of a research project on the sensitizing potency of epoxy resin compounds (FP-0324). A retrospective analysis of data from the Information Network of Departments of Dermatology (IVDK), 2002-2011, and a comparison of reaction frequencies with (surrogate) exposure data, were performed. Almost half of the patients sensitized to epoxy resin were additionally sensitized to reactive diluents or hardeners. Among the reactive diluents, 1,6-hexanediol diglycidyl ether was the most frequent allergen, followed by 1,4-butanediol diglycidyl ether, phenyl glycidyl ether, and p-tert-butylphenyl glycidyl ether. Among the hardeners, m-xylylene diamine (MXDA) and isophorone diamine (IPDA) were the most frequent allergens. According to the calculated exposure-related frequency of sensitization, MXDA seems to be a far more important sensitizer than IPDA. Up to 60% of the patients sensitized to hardeners and 15-20% of those sensitized to reactive diluents do not react to epoxy resin. In cases of suspected contact allergy to an ERS, a complete epoxy resin series must be patch tested from the start. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Characterization of odorants in inflatable aquatic toys and swimming learning devices-which substances are causative for the characteristic odor and potentially harmful?

PubMed

Wiedmer, Christoph; Velasco-Schön, Cristina; Buettner, Andrea

2017-06-01

Based on the observation of intense and offensive smells in the product group of aquatic toys, four representative products were exemplarily chosen and sensorially characterized by an expert panel. Panellists reported mostly almond- and rubber-like notes for three of the four samples, whereas the smell of the fourth sample was dominated by organic solvent-associated notes such as "nail polish-like." To elucidate the molecular reasons of these smells, we isolated the volatile fraction of the product by solvent extraction and high vacuum distillation, and identified the main odorants by aroma extract dilution analysis (AEDA), followed by one- and two-dimensional gas chromatography, with parallel mass spectrometric and olfactometric detection. Additionally, the materials of the samples were identified by means of differential scanning calorimetry (DSC), attenuated total reflectance spectroscopy (ATR-spectroscopy), and Beilstein halogen test. Between 32 and 46 odors could be detected in each sample by means of AEDA, whereby five to 13 of these compounds were detectable with by far the highest dilution factors, and were found to primarily correlate with the smells of the respective products. Focussing the subsequent identification on these causative substances led to the successful identification of the majority of these odorants. Among them were several mono- or di-unsaturated carbonyl compounds and their epoxidized derivatives, which are typical odorous artefacts from fatty acid oxidation, but also odor-active organic solvents such as cyclohexanone, isophorone, and phenol.

Responses of the L51781Y tk/sup +//tk/sup -/ mouse lymphoma cell forward mutation assay: III. 72 coded chemicals

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGregor, D.B.; Brown, A.; Cattanach, P.

Seventy-two chemicals were tested for their mutagenic potential in the L51781Y tk/sup +///sup -/ mouse lymphoma cell forward mutation assay, using procedures based upon those described previously. Cultures were exposed to the chemicals for 4 hr, then cultured for 2 days before planting in soft agar with or without trifluorothymidine (TFT), 3 ..mu..g/ml. The chemicals were tested at least twice. Significant responses were obtained with allyl isothiocyanate, p-benzoquinone dioxime, benzyl acetate, 2-biphenylamine HCl, bis(2-chloro-1-methylethyl)ether, cadmium chloride, chlordane, chlorobenzene, chlorobenzilate, 2-chloroethanol, chlorothalonil, cytarabine x HCl, p,p'-DDE, diazinon, 2,6-dichloro-p-phenylenediamine, N,N-diethylthiourea, diglycidylresorcinol ether, 2,4-dimethoxy aniline x HCl, disperse yellow 3, endosulfan, 1,2-epoxyhexadecane, ethylmore » acrylate, ethyl benzene, ethylene thiourea, F D and C yellow Number 6, furan, heptachlor, isophorone, mercuric chloride, 4,4'-methylenedianiline x 2 HCl, methyl viologen, nickel sulfate x 6H/sub 2/O, 4,4'-oxydianiline, pentachloroethane, piperonyl butoxide, propyl gallate, quinoline, rotenone, 2,4,5,6-tetrachloro-4-nitro-anisole, 1,1,1,2-tetrachloroethane, trichlorfon, 2,4,6-trichlorophenol, 2,4,5-trimethoxybenzaldehyde, 1,1,3-trimethyl-2-thiourea, 1-vinyl-3-cyclopetene dioxide, vinyl toluene, and ziram. The assay was incapable of providing a clear indication of whether some chemicals were mutagens; these benzyl alcohol, 1,4-dichlorobenzene, phenol, succinic acid-2,2-dimethyl hydrazide, and toluene.« less

A strategy to synthesize graphene-incorporated lignin polymer composite materials with uniform graphene dispersion and covalently bonded interface engineering

NASA Astrophysics Data System (ADS)

Wang, Mei; Duong, Le Dai; Ma, Yifei; Sun, Yan; Hong, Sung Yong; Kim, Ye Chan; Suhr, Jonghwan; Nam, Jae-Do

2017-08-01

Graphene-incorporated polymer composites have been demonstrated to have excellent mechanical and electrical properties. In the field of graphene-incorporated composite material synthesis, there are two main obstacles: Non-uniform dispersion of graphene filler in the matrix and weak interface bonding between the graphene filler and polymer matrix. To overcome these problems, we develop an in-situ polymerization strategy to synthesize uniformly dispersed and covalently bonded graphene/lignin composites. Graphene oxide (GO) was chemically modified by 4,4'-methylene diphenyl diisocyanate (MDI) to introduce isocyanate groups and form the urethane bonds with lignin macromonomers. Subsequential polycondensation reactions of lignin groups with caprolactone and sebacoyl chloride bring about a covalent network of modified GO and lignin-based polymers. The flexible and robust lignin polycaprolactone polycondensate/modified GO (Lig-GOm) composite membranes are achieved after vacuum filtration, which have tunable hydrophilicity and electrical resistance according to the contents of GOm. This research transforms lignin from an abundant biomass into film-state composite materials, paving a new way for the utilization of biomass wastes.

New hybrid latexes from a soybean oil-based waterborne polyurethane and acrylics via emulsion polymerization.

PubMed

Lu, Yongshang; Larock, Richard C

2007-10-01

A series of new waterborne polyurethane (PU)/acrylic hybrid latexes have been successfully synthesized by the emulsion polymerization of acrylic monomers (butyl acrylate and methyl methacrylate) in the presence of a soybean oil-based waterborne PU dispersion using potassium persulfate as an initiator. The waterborne PU dispersion has been synthesized by a polyaddition reaction of toluene 2,4-diisocyanate and a soybean oil-based polyol (SOL). The resulting hybrid latexes, containing 15-60 wt % SOL as a renewable resource, are very stable and exhibit uniform particle sizes of 125 +/- 20 nm as determined by transmittance electronic microscopy. The structure, thermal, and mechanical properties of the resulting hybrid latex films have been investigated by Fourier transform infrared spectroscopy, solid state 13C NMR spectroscopy, dynamic mechanical analysis, extraction, and mechanical testing. Grafting copolymerization of the acrylic monomers onto the PU network occurs during the emulsion polymerization, leading to a significant increase in the thermal and mechanical properties of the resulting hybrid latexes. This work provides a new way of utilizing renewable resources to prepare environmentally friendly hybrid latexes with high performance for coating applications.

FTIR and molecular mechanics studies of H-bonds in aliphatic polyurethane and polyamide-66 model molecules.

PubMed

Wang, Guoqing; Zhang, Chunxia; Guo, Xiaohe; Ren, Zhiyong

2008-02-01

Model aliphatic polyurethane (APU) hard segment based on 1,6-hexamethylene diisocyanate (HDI) and 1,4-butanediol (BDO) were prepared. FTIR and molecular mechanics (MM) simulation were used to conduct the systematic studies on APU and polyamide-66 (PA-66) whose sole difference lies in the alkoxyl oxygen. It was found that the introduction of the alkoxyl not only increases the conformations in APU, makes it a possible H-bond acceptor, but also weakens the H-bond between NH and O=C in APU. There are two conformers stably existed in APU with lowest energy, leading to eight H-bond complexes based on NH as donor and (1) O=C as acceptor, and another two complexes based on (2) alkoxyl O and (3) urethane N as acceptors, whereas there is only one stable conformer in PA-66, leading to one H-bond complex. One predominant H-bond complex has been found in APU with probability of about 95%. The simulated results are consistent with the nuNH and nuC=O band shifting in FTIR.

FTIR and molecular mechanics studies of H-bonds in aliphatic polyurethane and polyamide-66 model molecules

NASA Astrophysics Data System (ADS)

Wang, Guoqing; Zhang, Chunxia; Guo, Xiaohe; Ren, Zhiyong

2008-02-01

Model aliphatic polyurethane (APU) hard segment based on 1,6-hexamethylene diisocyanate (HDI) and 1,4-butanediol (BDO) were prepared. FTIR and molecular mechanics (MM) simulation were used to conduct the systematic studies on APU and polyamide-66 (PA-66) whose sole difference lies in the alkoxyl oxygen. It was found that the introduction of the alkoxyl not only increases the conformations in APU, makes it a possible H-bond acceptor, but also weakens the H-bond between NH and O dbnd C in APU. There are two conformers stably existed in APU with lowest energy, leading to eight H-bond complexes based on NH as donor and (1) O dbnd C as acceptor, and another two complexes based on (2) alkoxyl O and (3) urethane N as acceptors, whereas there is only one stable conformer in PA-66, leading to one H-bond complex. One predominant H-bond complex has been found in APU with probability of about 95%. The simulated results are consistent with the νNH and νC dbnd O band shifting in FTIR.

Residual Isocyanates in Medical Devices and Products: A Qualitative and Quantitative Assessment

PubMed Central

Franklin, Gillian; Harari, Homero; Ahsan, Samavi; Bello, Dhimiter; Sterling, David A.; Nedrelow, Jonathan; Raynaud, Scott; Biswas, Swati; Liu, Youcheng

2016-01-01

We conducted a pilot qualitative and quantitative assessment of residual isocyanates and their potential initial exposures in neonates, as little is known about their contact effect. After a neonatal intensive care unit (NICU) stockroom inventory, polyurethane (PU) and PU foam (PUF) devices and products were qualitatively evaluated for residual isocyanates using Surface SWYPE™. Those containing isocyanates were quantitatively tested for methylene diphenyl diisocyanate (MDI) species, using UPLC-UV-MS/MS method. Ten of 37 products and devices tested, indicated both free and bound residual surface isocyanates; PU/PUF pieces contained aromatic isocyanates; one product contained aliphatic isocyanates. Overall, quantified mean MDI concentrations were low (4,4′-MDI = 0.52 to 140.1 pg/mg) and (2,4′-MDI = 0.01 to 4.48 pg/mg). The 4,4′-MDI species had the highest measured concentration (280 pg/mg). Commonly used medical devices/products contain low, but measurable concentrations of residual isocyanates. Quantifying other isocyanate species and neonatal skin exposure to isocyanates from these devices and products requires further investigation. PMID:27773989

Fabrication and characterization of a novel hydrophobic CaCO3 grafted by hydroxylated poly(vinyl chloride) chains

NASA Astrophysics Data System (ADS)

Bao, Lixia; Yang, Simei; Luo, Xin; Lei, Jingxin; Cao, Qiue; Wang, Jiliang

2015-12-01

The hydroxylated PVC (PVC-OH) was successfully synthesized by a suspension polymerization of vinyl chloride (VC), butyl acrylate (BA) and hydroxyethyl acrylate (HEA). Novel hydrophobic CaCO3 was then prepared by a urethane formation reaction between methylene diphenyl diisocyanate (MDI) and the sbnd OH groups both in the PVC-OH chains and on the surface of pristine CaCO3 particles. The effect of the PVC-OH content on the grafting ratio of treated CaCO3 particles was extensively investigated. Combining the result of Fourier transform infrared (FTIR) with that of water contact angle, it can be concluded that the hydrophobicity of CaCO3 had been efficiently improved by the PVC-OH segments grafted on the surface of CaCO3 particles. X-ray diffraction (XRD), thermal gravity analysis (TGA), scanning electron microscope (SEM) and transmission electron microscope (TEM) were also used to study crystalline behaviors, thermal stability and surface morphology of the modified CaCO3 particles, respectively. The change of specific surface area implying surface modification was investigated as well.

Development of high-performance biodegradable rigid polyurethane foams using all bioresource-based polyols: Lignin and soy oil-derived polyols.

PubMed

Luo, Xiaogang; Xiao, Yuqin; Wu, Qiangxian; Zeng, Jian

2018-04-25

Development of biodegradable polyurethane materials is the most promising in the wider context of the "greening" of industrial chemistry. To tackle this challenge, a novel biodegradable polyurethane foam from all bioresource-based polyols (lignin and soy oil-derived polyols) and polymeric methyldiphenyl diisocyanate (pMDI) have been synthesized via a one-pot and self-rising process. All these foam samples have the internal cellular morphology and microstructure. FTIR result exhibits characteristic peaks of polyurethane, and indicates covalent bonds between soy-based polyurethane and lignin, and the lignin powders can react with pMDI via active -H and -CNO. In addition, hydrogen bonding also plays an important role in forming the 3D structures. These interactions and chemical bonds made the prepared foam samples form the 3D macromolecular structure with improved mechanical, thermal, and biodegradable properties. The reaction process is time-saving and cost-effective as it requires no blowing agent and minimum processing steps, while exploring the potential of using the higher content of nature bioresource constituents. Copyright © 2018 Elsevier B.V. All rights reserved.

Thermal, Morphological and Rheological Properties of Rigid Polyurethane Foams as Thermal Insulating Materials

NASA Astrophysics Data System (ADS)

Kim, Ji Mun; Han, Mi Sun; Kim, Youn Hee; Kim, Woo Nyon

2008-07-01

The polyurethane foams (PUFs) were prepared by polyether polyols, polymeric 4,4'-diphenylmethane diisocyanate (PMDI), silicone surfactants, amine catalysts and cyclopentane as a blowing agent. Solid and liquid type fillers were used as a nucleating agent to decrease a cell size of the PUFs as well as improve the thermal insulating properties of the PUFs. The PUFs were prepared by adding solid and liquid type fillers in the range of 1 to 3 wt%. For the liquid type fillers, the cell size of the PUFs showed minimum and found to decrease compared the PUF without adding fillers. Also, thermal conductivity of the PUFs with adding fillers showed minimum. For the solid type fillers, cell size and thermal conductivity of the PUFs were observed to decrease with the filler content up to 3 wt%. From these results, it is suggested that the thermal insulating property of the PUFs can be improved by adding fillers as a nucleating agent. Also, storage and loss modulus of the PUFs will be presented to study gelling points of the PUFs.

Electrical, thermal and structural properties of plasticized waste cooking oil-based polyurethane solid polymer electrolyte

NASA Astrophysics Data System (ADS)

Huzaizi, Rahmatina Mohd; Tahir, Syuhada Mohd; Mahbor, Kamisah Mohamad

2017-12-01

Waste cooking oil-based polyol was synthesized using epoxidation and hydroxylation methods. The polyol was combined with 4,4-diphenylmethane diisocyanate to produce polyurethane (PU) to be used as polymer host in solid polymer electrolyte. 30 wt% LiClO4 was added as doping salt and two types of plasticizers were used; ethylene carbonate (PU-EC) and polyethylene glycol (PU-PEG). The SPE films were characterized using Fourier transform infrared spectroscopy, electrochemical impedance spectroscopy, differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The highest conductivity achieved was 8.4 x 10-8 S cm-1 upon addition of 10 wt% EC. The XRD results showed a decrease of crystalline peaks in PU-EC and the increase in PU-PEG. DSC results revealed that the films; PU, PU-EC and PU-PEG had glass transition temperatures of 159.7, 106.0 and 179.7 °C, respectively. The results showed that the addition of EC increased the amorphous region and the free volume in the SPE structure, thus resulted in higher ionic conductivity.

Polycarbonate-based polyurethane as a polymer electrolyte matrix for all-solid-state lithium batteries

NASA Astrophysics Data System (ADS)

Bao, Junjie; Shi, Gaojian; Tao, Can; Wang, Chao; Zhu, Chen; Cheng, Liang; Qian, Gang; Chen, Chunhua

2018-06-01

Four kinds of polycarbonate-based polyurethane with 8-14 wt% hard segments content are synthesized via reactions of polycarbonatediol, hexamethylene diisocyanate and diethylene glycol. The mechanical strength of the polyurethanes increase with the increase of hard segments content. Solid polymer electrolytes composed of the polycarbonate-based polyurethanes and LiTFSI exhibits fascinating characteristics for all-solid-state lithium batteries with a high ionic conductivity of 1.12 × 10-4 S cm-1 at 80 °C, an electrochemical stability window up to 4.5 V (vs. Li+/Li), excellent mechanical strength and superior interfacial stability against lithium metal. The all-solid-state batteries using LiFePO4 cathode can deliver high discharge capacities (161, 158, 134 and 93 mAh g-1 at varied rates of 0.2, 0.5, 1 and 2 C) at 80 °C and excellent cycling performance (with 91% capacity retention after 600 cycles at 1 C). All the results indicate that such a polyurethane-based solid polymer electrolyte can be a promising candidate for all-solid-state lithium batteries.

Synthesis and surface properties of polyurethane end-capped with hybrid hydrocarbon/fluorocarbon double-chain phospholipid.

PubMed

Li, Jiehua; Zhang, Yi; Yang, Jian; Tan, Hong; Li, Jianshu; Fu, Qiang

2013-05-01

To improve hemocompatibility of biomedical polyurethanes (PUs), a series of new fluorinated phospholipid end-capped polyurethanes (FPCPUs) as blending PU additives were designed and synthesized using diphenyl methane diisocyanate and 1,4-butanediol as hard segment, poly(tetramethylene glycol), polypropylene glycol, polycarbonate diols, and polyethylene glycol as soft segments, respectively, aminofunctionalized hybrid hydrocarbon/fluorocarbon double-chain phospholipid as end-capper. The bulk structures and surface properties of the obtained FPCPUs were fully characterized by (1)H NMR, Fourier transform infrared, gel permeation chromatography, X-ray photoelectron spectroscopy, differential scanning calorimetry, atomic force microscopy, and water contact angle measurement. It was found that the phosphatidylcholine groups could enrich on the surfaces and subsurfaces with the help of the fluorocarbon chains and self-assemble into mimic biomembrane on these polymer surfaces. These surfaces could effectively suppress fibrinogen adsorption, as evaluated by enzyme-linked immunosorbent assay method. Our work indicates that the FPCPUs should be one of the most potential modified additives for enhancing hemocompatibility of traditional medical PUs. Copyright © 2012 Wiley Periodicals, Inc.

Technology transfer through a network of standard methods and recommended practices - The case of petrochemicals

NASA Astrophysics Data System (ADS)

Batzias, Dimitris F.; Karvounis, Sotirios

2012-12-01

Technology transfer may take place in parallel with cooperative action between companies participating in the same organizational scheme or using one another as subcontractor (outsourcing). In this case, cooperation should be realized by means of Standard Methods and Recommended Practices (SRPs) to achieve (i) quality of intermediate/final products according to specifications and (ii) industrial process control as required to guarantee such quality with minimum deviation (corresponding to maximum reliability) from preset mean values of representative quality parameters. This work deals with the design of the network of SRPs needed in each case for successful cooperation, implying also the corresponding technology transfer, effectuated through a methodological framework developed in the form of an algorithmic procedure with 20 activity stages and 8 decision nodes. The functionality of this methodology is proved by presenting the path leading from (and relating) a standard test method for toluene, as petrochemical feedstock in the toluene diisocyanate production, to the (6 generations distance upstream) performance evaluation of industrial process control systems (ie., from ASTM D5606 to BS EN 61003-1:2004 in the SRPs network).

A water-soluble, mucoadhesive quaternary ammonium chitosan-methyl-β-cyclodextrin conjugate forming inclusion complexes with dexamethasone.

PubMed

Piras, Anna Maria; Zambito, Ylenia; Burgalassi, Susi; Monti, Daniela; Tampucci, Silvia; Terreni, Eleonora; Fabiano, Angela; Balzano, Federica; Uccello-Barretta, Gloria; Chetoni, Patrizia

2018-03-30

The ocular bioavailability of lipophilic drugs, such as dexamethasone, depends on both drug water solubility and mucoadhesion/permeation. Cyclodextrins and chitosan are frequently employed to either improve drug solubility or prolong drug contact onto mucosae, respectively. Although the covalent conjugation of cyclodextrin and chitosan brings to mucoadhesive drug complexes, their water solubility is restricted to acidic pHs. This paper describes a straightforward grafting of methyl-β-cyclodextrin (MCD) on quaternary ammonium chitosan (QA-Ch60), mediated by hexamethylene diisocyanate. The resulting product is a water-soluble chitosan derivative, having a 10-atom long spacer between the quaternized chitosan and the cyclodextrin. The derivative is capable of complexing the model drug dexamethasone and stable complexes were also observed for the lyophilized products. Furthermore, the conjugate preserves the mucoadhesive properties typical of quaternized chitosan and its safety as solubilizing excipient for ophthalmic applications was preliminary assessed by in vitro cytotoxicity evaluations. Taken as a whole, the observed features appear promising for future processing of the developed product into 3D solid forms, such as controlled drug delivery systems, films or drug eluting medical devices.

Synthesis and characterization of chitosan/curcumin blends based polyurethanes.

PubMed

Zia, Fatima; Zia, Khalid Mahmood; Zuber, Mohammad; Rehman, Saima; Tabasum, Shazia; Sultana, Salma

2016-11-01

In this work, new hexamethylene diisocyanate (HMDI) and hyroxylterminated polybutadiene (HTPB) based polyurethanes (PUs) were prepared following step growth polymerization by the introduction of varying mole ratio of chitosan (CH) and curcumin (CUR). Structural study of blends through infrared spectroscopy confirmed the incorporation of CH and CUR into the backbone of the PU. The scanning electron microscopic (SEM) study confirmed the well dispersion of incorporated chitosan/curcumin and homogeneity of surface of synthesized samples. Thermogravimetric analysis (TGA) of PU blends indicated a better thermal stability with 0.25M:0.75M of chitosan to curcumin. Mechanical properties such as modulus and tensile strength of PU blends were found to be better with higher contents of chitosan and curcumin. The same extender composition (1mol BDO, 075mol chitosan and 0.25mol curcumin) based PU showed higher substantial of antimicrobial activity as compared to the all other PUs. On the whole, this work is actually a step towards the generation of novel biocompatible materials preferably useful for biomedical applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Artificial extracellular matrix for biomedical applications: biocompatible and biodegradable poly (tetramethylene ether) glycol/poly (ε-caprolactone diol)-based polyurethanes.

PubMed

Shahrousvand, Mohsen; Mir Mohamad Sadeghi, Gity; Salimi, Ali

2016-12-01

The cells as a tissue component need to viscoelastic, biocompatible, biodegradable, and wettable extracellular matrix for their biological activity. In this study, in order to prepare biomedical polyurethane elastomers with good mechanical behavior and biodegradability, a series of novel polyester-polyether- based polyurethanes (PUs) were synthesized using a two-step bulk reaction by melting pre-polymer method, taking 1,4-Butanediol (BDO) as chain extender, hexamethylene diisocyanate as the hard segment, and poly (tetramethylene ether) glycol (PTMEG) and poly (ε-caprolactone diol) (PCL-Diol) as the soft segment without a catalyst. The soft to the hard segment ratio was kept constant in all samples. Polyurethane characteristics such as thermal and mechanical properties, wettability and water adsorption, biodegradability, and cellular behavior were changed by changing the ratio of polyether diol to polyester diol composition in the soft segment. Our present work provides a new procedure for the preparation of engineered polyurethanes in surface properties and biodegradability, which could be a good candidate for bone, cartilage, and skin tissue engineering.

Thermal, Mechanical, and Electrical Properties of Graphene Nanoplatelet/Graphene Oxide/ Polyurethane Hybrid Nanocomposite.

PubMed

Pokharel, Pashupati; Lee, Sang Hyub; Lee, Dai Soo

2015-01-01

Hybrid nanocomposites of polyurethane (PU) were prepared by in-situ polymerization of 4,4'- diphenyl methane diisocyanate (MDI) with mixture of graphene oxide (GO) and graphene nanoplatelet (GNP) dispersed in a poly(tetramethylene ether glycol) (PTMEG). Effects of the fillers, GO and GNP, on the thermal, mechanical, and electrical properties of the nanocomposites of PU were investigated. Sonication of the hybrid of GNP and GO with PTMEG enabled effective dispersion of the fillers in the solution than the sonication of GNP alone. The addition of PTMEG in the solution prevented the GNPs from the restacking during the drying process. It was observed that the electrical conductivity and mechanical property of the nanocomposites based on the hybrid of GO and GNP were superior to the nanocomposite based on GNP alone at the same loading of the filler. At the loading of the 3 wt% hybrid filler in PU, we observed the improvement of Young's modulus -200% and the surface resistivity of 10(9.5) ohm/sq without sacrificing the elongation at break.

Thermal characterization and model free kinetics of aged epoxies and foams using TGA and DSC methods.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cordaro, Joseph Gabriel; Kruizenga, Alan Michael; Nissen, April

2013-10-01

Two classes of materials, poly(methylene diphenyl diisocyanate) or PMDI foam, and cross-linked epoxy resins, were characterized using thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC), to help understand the effects of aging and %E2%80%9Cbake-out%E2%80%9D. The materials were evaluated for mass loss and the onset of decomposition. In some experiments, volatile materials released during heating were analyzed via mass spectroscopy. In all, over twenty materials were evaluated to compare the mass loss and onset temperature for decomposition. Model free kinetic (MFK) measurements, acquired using variable heating rate TGA experiments, were used to calculate the apparent activation energy of thermal decomposition.more » From these compiled data the effects of aging, bake-out, and sample history on the thermal stability of materials were compared. No significant differences between aged and unaged materials were detected. Bake-out did slightly affect the onset temperature of decomposition but only at the highest bake-out temperatures. Finally, some recommendations for future handling are made.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffman, D.M.; Jessop, E.S.; Swansiger, R.W.

Cast cure, extrusion cast, and paste extrudable explosives have not been designed for transferring through long tortuous paths or into fine three dimensional shapes. To allow the crystalline explosive to flow a lubricating fluid is required. The energetic liquid ethane trinitrate (TMETN) was used as the lubricant to maximize the explosive energy. TMETN is a liquid nitrate ester which requires stabilization with conventional free radical stabilizers such as 2- nitrodiphenylamine, methyl-nitroanaline, or ethyl centrylite. Since these injection moldable explosives are expected to cure in place, a polyesterurethane binder based on polymeric isocyanate of hexamethylene diisocyanate and polycaprolactone polyols is dissolvedmore » in TMETN. The solubility of the polymer precursors in TMETN also reduces the energetic liquids sensitivity. The latent cure catalyst Dabco T-131 was used to minimize shrinkage associated with thermal expansion, reduce cost associated with oven cures, to give 4-6 hour potlife and overnight cure to handling strength. The product RX-08-HD is a new, low-viscosity, injection moldable explosive that can be extruded into complex, void-free shapes. Combined with appropriate design and other aspects of weaponization, RX-08-HD has produced outstanding results.« less

Preparation of polyurethane foams using liquefied oil palm mesocarp fibre (OPMF) and renewable monomer from waste cooking oil

NASA Astrophysics Data System (ADS)

Kormin, Shaharuddin; Rus, Anika Zafiah M.; Azahari, M. Shafiq M.

2017-09-01

The aim of this research is the production of polyurethane (PU) foams with biopolyols from liquefied oil palm mesocarp fibre (OPMF) and renewable monomer. Liquefaction of OPMF was studied using polyhydric alcohol (PA) which is PEG-400 as liquefaction solvents in conventional glass flask. In the second part of this paper was obtained the PU foams which presented good results when compared with commercial foams and include polyols from of fossil fuels. PU foams were prepared by mixing liquefied OPMF biopolyol, renewable monomer from waste cooking, additives and methylene diphenyl diisocyanate (MDI). Water was used as an environmental friendly blowing agent. The factors that influence the cell structure of foams (i.e., catalyst, surfactant, dosage of blowing agent, and mass ratio of biopolyol to renewable monomer were studied. The synthesized PU foams were characterized by FTIR and SEM. The formulation of the PU foams should be improved, but the results show that is possible the use biopolyols and renewable monomer to produce industrial foams with lower cost.

The deformation and failure response of closed-cell PMDI foams subjected to dynamic impact loading

DOE PAGES

Koohbor, Behrad; Mallon, Silas; Kidane, Addis; ...

2015-04-07

The present work aims to investigate the bulk deformation and failure response of closed-cell Polymeric Methylene Diphenyl Diisocyanate (PMDI) foams subjected to dynamic impact loading. First, foam specimens of different initial densities are examined and characterized in quasi-static loading conditions, where the deformation behavior of the samples is quantified in terms of the compressive elastic modulus and effective plastic Poisson's ratio. Then, the deformation response of the foam specimens subjected to direct impact loading is examined by taking into account the effects of material compressibility and inertia stresses developed during deformation, using high speed imaging in conjunction with 3D digitalmore » image correlation. The stress-strain response and the energy absorption as a function of strain rate and initial density are presented and the bulk failure mechanisms are discussed. As a result, it is observed that the initial density of the foam and the applied strain rates have a substantial influence on the strength, bulk failure mechanism and the energy dissipation characteristics of the foam specimens.« less

Polyurethane/fluor-hydroxyapatite nanocomposite scaffolds for bone tissue engineering. Part I: morphological, physical, and mechanical characterization

PubMed Central

Asefnejad, Azadeh; Behnamghader, Aliasghar; Khorasani, Mohammad Taghi; Farsadzadeh, Babak

2011-01-01

In this study, new nano-fluor-hydroxyapatite (nFHA)/polyurethane composite scaffolds were fabricated for potential use in bone tissue engineering. Polyester urethane samples were synthesized from polycaprolactone, hexamethylene diisocyanate, and 1,4-butanediol as chain extender. Nano fluor-hydroxyapatite (nFHA) was successfully synthesized by sol-gel method. The solid–liquid phase separation and solvent sublimation methods were used for preparation of the porous composites. Mechanical properties, chemical structure, and morphological characteristics of the samples were investigated by compressive test, Fourier transform infrared, and scanning electron microscopy (SEM) techniques, respectively. The effect of nFHA powder content on porosity and pore morphology was investigated. SEM images demonstrated that the scaffolds were constituted of interconnected and homogeneously distributed pores. The pore size of the scaffolds was in the range 50–250 μm. The result obtained in this research revealed that the porosity and pore average size decreased and compressive modulus increased with nFHA percentage. Considering morphological, physical, and mechanical properties, the scaffold with a higher ratio of nFHA has suitable potential use in tissue regeneration. PMID:21289986

Physical properties of polyurethane plastic sheets produced from polyols from canola oil.

PubMed

Kong, Xiaohua; Narine, Suresh S

2007-07-01

Polyurethane (PUR) plastic sheets were prepared by reacting polyols synthesized from canola oil with aromatic diphenylmethane diisocyanate. The properties of the material were measured by dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) as well as tensile properties measurements. The effect of stoichiometric balance (i.e., OH/NCO molar ratio) on the final properties was evaluated. The concentration of elastically active network chains (EANCs), nue, of the polymer networks was calculated using rubber elasticity theory. The glass transition temperatures (Tg) for the plastic sheets with OH/NCO molar ratios of 1.0/1.0, 1.0/1.1, and 1.0/1.2 were found to be 23, 41, and 43 degrees C, respectively. The kinetic studies of the degradation process of the PUR plastics showed three well-defined steps of degradation. The PUR plastic sheets with OH/NCO molar ratio 1.0/1.1 had the highest nue, lowest number-average molecule weight between cross-links, MC, and excellent mechanical properties, indicating that this is the optimum ratio in the PUR formulations.

Associations of symptoms related to isocyanate, ureaformol, and formophenolic exposures with respiratory symptoms and lung function in coal miners

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bertrand, J.P.; Simon, V.; Chau, N.

The respiratory effects of diphenylmethane diisocyanate (MDI)-based resins and ureaformol- and formophenolic-based resins, used in coal mining, are unknown. This cross-sectional study of 354 miners evaluated respiratory health in miners with MDI-related symptoms (IS) and ureaformol/formophenolic-related symptoms (UFS). The protocol included clinical examination, chest radiograph, questionnaire on respiratory symptoms, smoking habit, job history, resin handling, and spirometry. Resin handling concerned 27.7% of the miners. IS affected 5.6%, and 1.4% also after work. UFS affected 22.6%, and 2.3% also after work. Wheezing affected 35.6%; chronic cough, expectoration, or bronchitis about 10%; dyspnea 5.4%; and asthma 2.8%. The miners with UFS hadmore » significantly more frequent chronic cough, expectoration, chronic bronchitis, dyspnea, and wheezing, whereas those with IS at and after work had markedly lower FVC, FEV1, MMEF, FEF50% and FEF25%. These findings raise the possibility of deleterious effects of exposures to MDI and ureaformol/ ormophenolic resins on respiratory health and lung function in coal miners during their working life.« less

Testing of Disposable Protective Garments Against Isocyanate Permeation From Spray Polyurethane Foam Insulation.

PubMed

Mellette, Michael P; Bello, Dhimiter; Xue, Yalong; Yost, Michael; Bello, Anila; Woskie, Susan

2018-05-12

Diisocyanates (isocyanates), including methylene diphenyl diisocyanate (MDI), are the primary reactive components of spray polyurethane foam (SPF) insulation. They are potent immune sensitizers and a leading cause of occupational asthma. Skin exposure to isocyanates may lead to both irritant and allergic contact dermatitis and possibly contribute to systemic sensitization. More than sufficient evidence exists to justify the use of protective garments to minimize skin contact with aerosolized and raw isocyanate containing materials during SPF applications. Studies evaluating the permeation of protective garments following exposure to SPF insulation do not currently exist. To conduct permeation testing under controlled conditions to assess the effectiveness of common protective gloves and coveralls during SPF applications using realistic SPF product formulations. Five common disposable garment materials [disposable latex gloves (0.07 mm thickness), nitrile gloves (0.07 mm), vinyl gloves (0.07 mm), polypropylene coveralls (0.13 mm) and Tyvek coveralls (0.13 mm)] were selected for testing. These materials were cut into small pieces and assembled into a permeation test cell system and coated with a two-part slow-rise spray polyurethane foam insulation. Glass fiber filters (GFF) pretreated with 1-(9-anthracenylmethyl)piperazine) (MAP) were used underneath the garment to collect permeating isocyanates. GFF filters were collected at predetermined test intervals between 0.75 and 20.00 min and subsequently analyzed using liquid chromatography-tandem mass spectrometry. For each garment material, we assessed (i) the cumulative concentration of total isocyanate, including phenyl isocyanate and three MDI isomers, that effectively permeated the material over the test time; (ii) estimated breakthrough detection time, average permeation rate, and standardized breakthrough time; from which (iii) recommendations were developed for the use of similar protective garments following contamination by two-component spray polyurethane foam systems and the limitations of such protective garments were identified. Each type of protective garment material demonstrated an average permeation rate well below the ASTM method F-739 standardized breakthrough rate threshold of 100.0 ng/cm2 min-1. Disposable latex gloves displayed the greatest total isocyanate permeation rate (4.11 ng/cm2 min-1), followed by the vinyl and nitrile gloves, respectively. The Tyvek coverall demonstrated a greater average rate of isocyanate permeation than the polypropylene coveralls. Typical isocyanate loading was in the range of 900 to 15,000 ng MDI/cm2. Permeation test data collected during this study indicated that each type of protective garment evaluated, provided a considerable level of protection (i.e. 10-110-fold reduction from the level of direct exposure) against the isocyanate component of the SPF insulation mixture. Nitrile gloves and polypropylene coveralls demonstrated the lowest rate of permeation and the lowest cumulative permeation of total isocyanate for each garment type.

A new penetration test method: protection efficiency of glove and clothing materials against diphenylmethane diisocyanate (MDI).

PubMed

Henriks-Eckerman, Maj-Len; Mäkelä, Erja

2015-03-01

Reported cases of allergic contact dermatitis caused by methylenediphenyl diisocyanate (MDI) have increased and thereby increased the need for adequate skin protection. Current standardized permeation and penetration test methods give information about efficacy of protective materials against individual components of the polyurethane systems. They do not give information of what kind of clothing materials workers should wear against splashes when handling mixed MDI-polyurethane formulations, which contain MDI, its oligomers, and polyols. The aim of this study was to develop and validate a sensitive penetration test method that can be used to select clothing that is protective enough against uncured splashes of MDI-polyurethane, still easy to use, and also, to find affordable glove materials that provide adequate protection during a short contact. The penetration of MDI through eight representative glove or clothing materials was studied with the developed test procedure. One MDI hardener and two polymeric MDI (PMDI)-polyol formulations representing different curing times were used as test substances. The materials tested included work clothing (woven) fabric, arm shields (nonwoven fabric), old T-shirt, winter gloves, and gloves of nitrile rubber, leather, vinyl (PVC), and natural rubber. A drop (50 µl) of test substance was added to the outer surface of the glove/clothing material, which had Tape Fixomull attached to the inner surface as a collection medium. After penetration times of 5 or 20min, the collecting material was removed and immediately immersed into acetonitrile containing 1-(2-methoxyphenyl)-piperazine for derivatization. The formed urea derivatives of 2,4'-MDI and 4,4'-MDI were analysed using liquid chromatography with mass spectrometric and UV detection. The precision of the test method was good for the material with high penetration (work clothing fabric) of MDI, as the relative standard deviation (RSD) was 14 and 20%. For the arm shield with a low penetration (the nonwoven fabric), the precision was lower with RSDs of 35 and 50%. For two clothing materials, the penetration was high (134-577 µg cm(-2)). Low penetration (<0.5 µg cm(-2)) was shown by the arm shield and the natural rubber glove. Three glove materials showed no detectable MDI penetration (<0.002 µg cm(-2)). Two affordable glove materials (natural rubber and nitrile rubber) and one clothing material (dust proof arm shield) that can provide adequate protection during short contact with solvent free PMDI formulations were found. The new test procedure should be standardized in order to get a new international penetration standard. © The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Viscosity induced emission of red-emitting NLOphoric coumarin morpholine-thiazole hybrid styryl dyes as FMRs: Consolidated experimental and theoretical approach

NASA Astrophysics Data System (ADS)

Avhad, Kiran C.; Patil, Dinesh S.; Chitrambalam, S.; Sreenath, M. C.; Joe, I. Hubert; Sekar, Nagaiyan

2018-05-01

Four new coumarin hybrid styryl dyes are synthesized by condensing 4-(7-(diethylamino)-2-oxo-2H-chromen-3-yl)-2-morpholinothiazole-5-carbaldehyde with dicyanovinylene containing active methylene intermediates and their linear and non-linear optical properties are studied. The dye having dicyanovinylene-isophorone acceptor displayed a large Stokes shift of 3702-4795 cm-1 in non-polar to polar solvent respectively. The dyes exhibit a good charge transfer characteristics and positive emission solvatochromism (∼50 nm-72 nm) in non-polar to a polar solvent which is well supported by multi-linear regression analysis. Viscosity induced enhancement study in ethanol/polyethylene glycol-400 system shows 2.71-6.78 fold increase in emission intensity. The intra and twisted-intramolecular charge transfer (ICT-TICT) characteristics were established using emission solvatochromism, polarity plots, generalised Mullikan-Hush (GMH) analysis and optimized geometry. A dye having the highest charge transfer dipole moment relatively possess the maximum two-photon absorption cross-section area (KK-1 = 165-207 GM) which was established using theoretical two-level model. The NLO properties have been investigated employing solvatochromic and computational methods and were found to be directly proportional to the polarity of the solvent. Z-scan results reveal that the dyes KK-1 and KK-2 possesses reverse saturable kind of behaviour whereas KK-3 and KK-4 show saturable kind of behaviour. From the experimental and theoretical data, these coumarin thiazole hybrid dyes can be considered as promising candidates for FMR and NLOphores.

Liquid chromatography method to determine polyamines in thermosetting polymers.

PubMed

Dopico-García, M S; López-Vilariño, J M; Fernández-Martínez, G; González-Rodríguez, M V

2010-05-14

A simple, robust and sensitive analytical method to determine three polyamines commonly used as hardeners in epoxy resin systems and in the manufacture of polyurethane is reported. The studied polyamines are: one tetramine, TETA (triethylenetetramine), and two diamines, IPDA (Isophorone diamine) and TCD-diamine (4,7-methano-1H-indene-5,?-dimethanamine, octahydro-). The latter has an incompletely defined structure, and, as far as we know, has not been previously determined by other methods. All three polyamines contain primary amines; TETA also contains secondary amines. The analytical method involves derivatization with 6-aminoquinolyl-N-hydroxysuccinimidyl carbamate, used for the first time for these compounds, followed by high performance liquid chromatography (HPLC) analysis with a fluorescence (FL) detector (lambda excitation 248nm, lambda emision 395nm). The HPLC-DAD-LTQ Orbitrap MS was used in order to provide structural information about the obtained derivatized compounds. The hybrid linear ion trap LTQ Orbitrap mass spectrometer has been introduced in recent years and provides a high mass accuracy. The structures of the derivatized analytes were identified from the protonated molecular ions [M+H](+) and corresponded to the fully labelled analytes. The following analytical parameters were determined for the method using the HPLC-FL: linearity, precision (2.5-10%), instrumental precision intraday (0.8-1.5%) and interday (2.9-6.3%), and detection limits (0.02-0.14mgL(-1)). The stability of stock solutions and derivatized compounds was also investigated. The method was applied to determine the amine free content in epoxy resin dust collected in workplaces. Copyright 2010 Elsevier B.V. All rights reserved.

A Boltzmann machine for the organization of intelligent machines

NASA Technical Reports Server (NTRS)

Moed, Michael C.; Saridis, George N.

1989-01-01

In the present technological society, there is a major need to build machines that would execute intelligent tasks operating in uncertain environments with minimum interaction with a human operator. Although some designers have built smart robots, utilizing heuristic ideas, there is no systematic approach to design such machines in an engineering manner. Recently, cross-disciplinary research from the fields of computers, systems AI and information theory has served to set the foundations of the emerging area of the design of intelligent machines. Since 1977 Saridis has been developing an approach, defined as Hierarchical Intelligent Control, designed to organize, coordinate and execute anthropomorphic tasks by a machine with minimum interaction with a human operator. This approach utilizes analytical (probabilistic) models to describe and control the various functions of the intelligent machine structured by the intuitively defined principle of Increasing Precision with Decreasing Intelligence (IPDI) (Saridis 1979). This principle, even though resembles the managerial structure of organizational systems (Levis 1988), has been derived on an analytic basis by Saridis (1988). The purpose is to derive analytically a Boltzmann machine suitable for optimal connection of nodes in a neural net (Fahlman, Hinton, Sejnowski, 1985). Then this machine will serve to search for the optimal design of the organization level of an intelligent machine. In order to accomplish this, some mathematical theory of the intelligent machines will be first outlined. Then some definitions of the variables associated with the principle, like machine intelligence, machine knowledge, and precision will be made (Saridis, Valavanis 1988). Then a procedure to establish the Boltzmann machine on an analytic basis will be presented and illustrated by an example in designing the organization level of an Intelligent Machine. A new search technique, the Modified Genetic Algorithm, is presented and proved to converge to the minimum of a cost function. Finally, simulations will show the effectiveness of a variety of search techniques for the intelligent machine.

Fe-Ni Nanoparticles supported on carbon nanotube-co-cyclodextrin polyurethanes for the removal of trichloroethylene in water

NASA Astrophysics Data System (ADS)

Krause, Rui W. M.; Mamba, Bhekie B.; Dlamini, Langelihle N.; Durbach, Shane H.

2010-02-01

Nanoscale bimetallic particles of nickel on iron were supported on carbon nanotubes and then co-polymerized with β-cyclodextrin (CNTs/CD) and the resulting polymers applied to the degradation of pollutants in water. The bimetallic nanoparticles (BMNPs) were first embedded on functionalized carbon nanotubes (f-CNTs) before being copolymerized with beta cyclodextrin (β-CD) and hexamethylene diisocyanate (HMDI) forming a water-insoluble polyurethane. The particle size and distribution of BMNPs were determined by Transmission Electron Microscopy (TEM), and the surface area was determined by using the Brunauer-Emmett-Teller (BET) method. Energy dispersive X-ray spectroscopy (EDXS) was used to confirm the formation of the BMNPs. Degradation of trichloroethylene (TCE) as a model pollutant was studied and more than 98% reduction in TCE was achieved by the polymers. Polymers with the BMNPs maintained their efficiency in degrading TCE after several cycles compared to metal-free polymers. The degradation was monitored by using gas chromatography-mass spectrometry (GC-MS), while the production of chlorides was verified by using ion chromatography (IC). Atomic absorption spectroscopy (AAS) was employed to determine the possible leaching of the BMNPs from the polymer, and confirmed to be extremely low.

Adhesion of nitrile rubber to UV-assisted surface chemical modified PET fabric, part II: Interfacial characterization of MDI grafted PET

NASA Astrophysics Data System (ADS)

Razavizadeh, Mahmoud; Jamshidi, Masoud

2016-08-01

Fiber to rubber adhesion is an important subject in rubber industry. It is well known that surface treatment (i.e. physical, mechanical and chemical) is an effective method to improve interfacial bonding of fibers and/or fabrics to rubbers. UV irradiation is an effective method which has been used to increase fabric-rubber interfacial interactions. In this research UV assisted chemical modification of PET fabrics was used to increase PET to nitrile rubber (NBR) adhesion. Nitrile rubber is a perfect selection as fuel and oil resistant rubber. However it has weak bonding to PET fabric. For this purpose PET fabric was carboxylated under UV irradiation and then methylenediphenyl diisocyanate (MDI) was grafted on carboxylated PET. The chemical composition of the fabric before and after surface treatment was investigated by X-ray photoelectron spectroscopy (XPS). The sectional morphology of the experimental PET fibers and the interface between rubber compound and PET fabric was studied using scanning electron microscope (SEM). The morphology and structure of the product were analyzed by an energy dispersive X-ray spectrometer (EDX). FTIR-ATR and H NMR analysis were used to assess surface modifications on the PET irradiated fabrics.

Thermomechanical Properties, Antibiotic Release, and Bioactivity of a Sterilized Cyclodextrin Drug Delivery System

PubMed Central

Halpern, Jeffrey M.; Gormley, Catherine A.; Keech, Melissa; von Recum, Horst A.

2014-01-01

Various local drug delivery devices and coatings are being developed as slow, sustained release mechanism for drugs, yet the polymers are typically not evaluated after commercial sterilization techniques. We examine the effect that commercial sterilization techniques have on the physical, mechanical, and drug delivery properties of polyurethane polymers. Specifically we tested cyclodextrin-hexamethyl diisocyanate crosslinked polymers before and after autoclave, ethylene oxide, and gamma radiation sterilization processes. We found that there is no significant change in the properties of polymers sterilized by ethylene oxide and gamma radiation compared to non-sterilized polymers. Polymers sterilized by autoclave showed increased tensile strength (p<0.0001) compared to non-sterilized polymers . In the release of drugs, which were loaded after the autoclave sterilization process, we observed a prolonged release (p<0.05) and a prolonged therapeutic effect (p<0.05) but less drug loading (p<0.0001) compared to non-sterilized polymers. The change in the release profile and tensile strength in polymers sterilized by autoclave was interpreted as being caused by additional crosslinking from residual, unreacted, or partially-reacted crosslinker contained within the polymer. Autoclaving therefore represents additional thermo-processing to modify rate and dose from polyurethanes and other materials. PMID:24949201

Effects of the Acrylic Polyol Structure and the Selectivity of the Employed Catalyst on the Performance of Two-Component Aqueous Polyurethane Coatings

PubMed Central

Cakic, Suzana; Lacnjevac, Caslav; Stamenkovic, Jakov; Ristic, Nikola; Takic, Ljiljana; Barac, Miroljub; Gligoric, Miladin

2007-01-01

Two kinds of aqueous acrylic polyols (single step and multi step synthesis type) have been investigated for their performance in the two-component aqueous polyurethane application, by using more selective catalysts. The aliphatic polyfunctional isocyanates based on hexamethylen diisocyanates have been employed as suitable hardeners. The complex of zirconium, commercially known as K-KAT®XC-6212, and manganese (III) complexes with mixed ligands based on the derivative of maleic acid have been used as catalysts in this study. Both of the aqueous polyols give good results, in terms of application and hardness, when elevated temperatures and more selective catalysts are applied. A more selective catalyst promotes the reaction between the isocyanate and polyol component. This increases the percentage of urethane bonds and the degree of hardness in the films formed from the two components of aqueous polyurethane lacquers. The polyol based on the single step synthesis route is favourable concerning potlife and hardness. The obtained results show that the performance of the two-component aqueous polyurethane coatings depends on the polymer structure of the polyols as well as on the selectivity of the employed catalyst.

Preparation and Characterization of Bioplastic-Based Green Renewable Composites from Tapioca with Acetyl Tributyl Citrate as a Plasticizer

PubMed Central

Tsou, Chi-Hui; Suen, Maw-Cherng; Yao, Wei-Hua; Yeh, Jen-Taut; Wu, Chin-San; Tsou, Chih-Yuan; Chiu, Shih-Hsuan; Chen, Jui-Chin; Wang, Ruo Yao; Lin, Shang-Ming; Hung, Wei-Song; Guzman, Manuel De; Hu, Chien-Chieh; Lee, Kueir-Rarn

2014-01-01

Granular tapioca was thermally blended with poly(lactic acid) (PLA). All blends were prepared using a plasti-corder and characterized for tensile properties, thermal properties and morphology. Scanning electron micrographs showed that phase separation occurred, leading to poor tensile properties. Therefore, methylenediphenyl diisocyanate (MDI) was used as an interfacial compatibilizer to improve the mechanical properties of PLA/tapioca blends. The addition of MDI could improve the tensile strength of the blend with 60 wt% tapioca, from 19.8 to 42.6 MPa. In addition, because PLA lacked toughness, acetyl tributyl citrate (ATBC) was added as a plasticizer to improve the ductility of PLA. A significant decrease in the melting point and glass-transition temperature was observed on the basis of differential scanning calorimetry, which indicated that the PLA structure was not dense after ATBC was added. As such, the brittleness was improved, and the elongation at break was extended to several hundred percent. Therefore, mixing ATBC with PLA/tapioca/MDI blends did exhibit the effect of plasticization and biodegradation. The results also revealed that excessive plasticizer would cause the migration of ATBC and decrease the tensile properties. PMID:28788150

Synthesis and Characterization of β-Cyclodextrin Functionalized Ionic Liquid Polymer as a Macroporous Material for the Removal of Phenols and As(V)

PubMed Central

Raoov, Muggundha; Mohamad, Sharifah; Abas, Mhd Radzi

2014-01-01

β-Cyclodextrin-ionic liquid polymer (CD-ILP) was first synthesized by functionalized β-cyclodextrin (CD) with 1-benzylimidazole (BIM) to form monofunctionalized CD (βCD-BIMOTs) and was further polymerized using a toluene diisocyanate (TDI) linker to form insoluble CD-ILP (βCD-BIMOTs-TDI). The βCD-BIMOTs-TDI polymer was characterized using various tools and the results obtained were compared with those derived from the native β-cyclodextrin polymer (βCD-TDI). The SEM result shows that the presence of ionic liquid (IL) increases the pore size, while the thermo gravimetric analysis (TGA) result shows that the presence of IL increases the stability of the polymer. Meanwhile, Brunauer-Emmett-Teller (BET) results show that βCD-BIMOTs-TDI polymer has 1.254 m2/g surface areas and the Barret-Joyner-Halenda (BJH) pore size distribution result reveals that the polymer exhibits macropores with a pore size of 77.66 nm. Preliminary sorption experiments were carried out and the βCD-BIMOTs-TDI polymer shows enhanced sorption capacity and high removal towards phenols and As(V). PMID:24366065

Preparation and characterization of plasticized palm-based polyurethane solid polymer electrolyte

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daud, Farah Nadia; Ahmad, Azizan; Badri, Khairiah Haji

2013-11-27

Palm-based polyurethane solid polymer electrolyte was prepared via prepolymerization method between palm kernel oil based polyols (PKO-p) and 2,4’-diphenylmethane diisocyanate (2,4’-MDI) in acetone at room temperature with the vary amount of lithium trifuoromethanesulfonate (LiCF{sub 3}SO{sub 3}) salt and polyethylene glycol (PEG). The film was analyzed using attenuated total reflection infrared (ATR-IR) spectroscopy, electrochemical impedance spectroscopy (EIS) and X-ray diffractometry (XRD). EIS result indicated ionic conductivity obtained with 30 wt% LiCF3SO3 increased to 6.55 × 10{sup −6} S cm{sup −1} when 10 wt.% of plasticizer was added into the system. FTIR analysis showed the interaction between lithium ions and amine (-N-H)more » at 3600–3100 cm{sup −1}, carbonyl (-C=O) at 1750–1650 cm{sup −1} and ether (-C-O-C-) at 1150–1000 cm{sup −1} of the polyurethane forming polymer-salt complexes. The XRD result confirmed that LiCF{sub 3}SO{sub 3} salt completely dissociated within the polyurethane film with the absence of crystalline peaks of LiCF{sub 3}SO{sub 3}.« less

Improved wettability and adhesion of polylactic acid/chitosan coating for bio-based multilayer film development

NASA Astrophysics Data System (ADS)

Gartner, Hunter; Li, Yana; Almenar, Eva

2015-03-01

The objective of this study was to investigate the effect of methyldiphenyl diisocyanate (MDI) concentration (0, 0.2, 1, 2, and 3%) on the wettability and adhesion of blend solutions of poly(lactic acid) (PLA) and chitosan (CS) when coated on PLA film for development of a bio-based multi-layer film suitable for food packaging and other applications. Characterization was carried out by attenuated total reflectance infrared spectrometry (ATR-FTIR), contact angle (θ), mechanical adhesion pull-off testing, and scanning electron microscopy (SEM). The θ of the PLA/CS blend shifted to a lower value (41-35°) with increasing MDI concentration showing that the surface tension was modified between the PLA/CS blend solution and PLA film and better wettability was achieved. The increase in MDI also resulted in an increased breaking strength (228-303 kPa) due to the increased H-bonding resulting from the more urethane groups formed within the PLA/CS blend as shown by ATR-FTIR. The improved adhesion was also shown by the increased number of physical entanglements observed by SEM. It can be concluded that MDI can be used to improve wettability and adhesion between PLA/CS coating and PLA film.

Sensory irritation and incapacitation evoked by thermal decomposition products of polymers and comparisons with known sensory irritants.

PubMed

Barrow, C S; Alarie, Y; Stock, M F

1978-01-01

A decrease in respiratory rate in mice during exposure to irritating airborne chemicals has been utilized as a response parameter to characterize the degree of upper respiratory tract irritation (sensory irritation) to the thermal decomposition products of various polymers. These included polystyrene, polyvinyl chloride, flexible polyurethane foam, polytetrafluorethylene, a fiber glass reinforced polyester resin, and Douglas Fir. Each of the materials was thermally decomposed in a low-mass vertical furnace in an air atmosphere at a programmed heating rate of 20 degrees C/min. Mice, in groups of four, were exposed to graded concentrations of the thermal decomposition products of each of the above materials. Dose-response curves were obtained by utilizing the maximum percent decrease in respiratory rate as the response parameter during each exposure. Comparison of these dose-response curves with other sensory irritants such as chlorine, ammonia, hydrogen chloride, sulfur dioxide, and toluene diisocyanate gave an indication of the sensory irrtation potential of the thermal decomposition products of these various polymers versus that of well-known single airborne chemical irritants. Total stress and incapacitation of the organism during exposure to sensory irritants such as from the thermal decomposition products of synthetic polymers is discussed.

Rigid polyurethane foam/cellulose whisker nanocomposites: preparation, characterization, and properties.

PubMed

Li, Yang; Ren, Hongfeng; Ragauskas, Arthur J

2011-08-01

Novel rigid polyurethane nanocomposite foams have been prepared by the polymerization of a sucrose-based polyol, a glycerol-based polyol and polymeric diphenylmethane diisocyanate in the presence of cellulose whiskers. Varying amounts of sulfuric acid hydrolyzed cellulose whiskers (0.25, 0.50, 0.75 and 1.00 wt%) prepared from a commercial fully bleached softwood kraft pulp were incorporated to investigate the effect of its dosage on the mechanical and thermal properties of polyurethane nanocomposites. Fourier transform infrared spectra of the nanocomposite foams suggested that additional hydrogen bonds were developed and crosslinking occurred between the hydroxyl groups of cellulose whiskers and isocyanate groups which increased the phase separation of soft and hard segments in the polyurethane. The closed cells of control foam and nanocomposite foams were homogeneously dispersed and the cell sizes were approximately 350 microm in diameter as observed by scanning electron microscope. A substantial improvement of mechanical properties at low whisker content (< or = 1.00 wt%) was obtained, especially the compressive strength and modulus at 1.00 wt% whiskers content which were increased by 269.7% and 210.0%, respectively. Thermal stability of the nanocomposites was also enhanced as determined by differential scanning calorimetry and thermogravimetric analysis.

Producing Lignin-Based Polyols through Microwave-Assisted Liquefaction for Rigid Polyurethane Foam Production.

PubMed

Xue, Bai-Liang; Wen, Jia-Long; Sun, Run-Cang

2015-02-10

Lignin-based polyols were synthesized through microwave-assisted liquefaction under different microwave heating times (5-30 min). The liquefaction reactions were carried out using polyethylene glycol (PEG-400)/glycerol as liquefying solvents and 97 wt% sulfur acid as a catalyst at 140 °C. The polyols obtained were analyzed for their yield, composition and structural characteristics using gel permeation chromatography (GPC), Fourier transform infrared (FT-IR) and nuclear magnetic resonance (NMR) spectra. FT-IR and NMR spectra showed that the liquefying solvents reacted with the phenol hydroxyl groups of the lignin in the liquefied product. With increasing microwave heating time, the viscosity of polyols was slightly increased and their corresponding molecular weight ( M W ) was gradually reduced. The optimal condition at the microwave heating time (5 min) ensured a high liquefaction yield (97.47%) and polyol with a suitable hydroxyl number (8.628 mmol/g). Polyurethane (PU) foams were prepared by polyols and methylene diphenylene diisocyanate (MDI) using the one-shot method. With the isocyanate/hydroxyl group ([NCO]/[OH]) ratio increasing from 0.6 to 1.0, their mechanical properties were gradually increased. This study provided some insight into the microwave-assisted liquefied lignin polyols for the production of rigid PU foam.

Structure-properties relationships of novel poly(carbonate-co-amide) segmented copolymers with polyamide-6 as hard segments and polycarbonate as soft segments

NASA Astrophysics Data System (ADS)

Yang, Yunyun; Kong, Weibo; Yuan, Ye; Zhou, Changlin; Cai, Xufu

2018-04-01

Novel poly(carbonate-co-amide) (PCA) block copolymers are prepared with polycarbonate diol (PCD) as soft segments, polyamide-6 (PA6) as hard segments and 4,4'-diphenylmethane diisocyanate (MDI) as coupling agent through reactive processing. The reactive processing strategy is eco-friendly and resolve the incompatibility between polyamide segments and PCD segments in preparation processing. The chemical structure, crystalline properties, thermal properties, mechanical properties and water resistance were extensively studied by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Differential scanning calorimetry (DSC), Thermal gravity analysis (TGA), Dynamic mechanical analysis (DMA), tensile testing, water contact angle and water absorption, respectively. The as-prepared PCAs exhibit obvious microphase separation between the crystalline hard PA6 phase and amorphous PCD soft segments. Meanwhile, PCAs showed outstanding mechanical with the maximum tensile strength of 46.3 MPa and elongation at break of 909%. The contact angle and water absorption results indicate that PCAs demonstrate outstanding water resistance even though possess the hydrophilic surfaces. The TGA measurements prove that the thermal stability of PCA can satisfy the requirement of multiple-processing without decomposition.

Several cases of work-related allergic contact dermatitis caused by isocyanates at a company manufacturing heat exchangers.

PubMed

Engfeldt, Malin; Isaksson, Marléne; Zimerson, Erik; Bruze, Magnus

2013-03-01

A 43-year-old woman was referred by her occupational health service with suspected occupational contact dermatitis. In connection with the investigation, a workplace visit was undertaken at her company, which used an adhesive based on pre-polymeric diphenylmethane diisocyanate in one of its units. During the visit, we became aware of six other employees with skin problems who were then referred to our department for investigation. To investigate the seven employees complaining about skin problems. Seven employees were patch tested with a baseline series, an isocyanate series, and a series with work material. Five of seven patients had occupational contact allergy. Four reacted to isocyanate-related test preparations, and one to a cleanser used at the workplace. Workplace visits constitute an important part of an occupational investigation, as they might give a broader picture of the problems at a company. In this case, it was found that 5 of 100 employees currently had or had previously had occupation-related skin problems. Owing to 'healthy worker selection', some of these patients might have been missed if we had not performed a full-scale workplace visit. © 2012 John Wiley & Sons A/S.

Electrospun nanofibrous scaffolds of segmented polyurethanes based on PEG, PLLA and PTMC blocks: Physico-chemical properties and morphology.

PubMed

Trinca, Rafael Bergamo; Abraham, Gustavo A; Felisberti, Maria Isabel

2015-11-01

Biocompatible polymeric scaffolds are crucial for successful tissue engineering. Biomedical segmented polyurethanes (SPUs) are an important and versatile class of polymers characterized by a broad spectrum of compositions, molecular architectures, properties and applications. Although SPUs are versatile materials that can be designed by different routes to cover a wide range of properties, they have been infrequently used for the preparation of electrospun nanofibrous scaffolds. This study reports the preparation of new electrospun polyurethane scaffolds. The segmented polyurethanes were synthesized using low molar masses macrodyols (poly(ethylene glycol), poly(l-lactide) and poly(trimethylene carbonate)) and 1,6-hexane diisocyanate and 1,4-butanodiol as isocyanate and chain extensor, respectively. Different electrospinning parameters such as solution properties and processing conditions were evaluated to achieve smooth, uniform bead-free fibers. Electrospun micro/nanofibrous structures with mean fiber diameters ranging from 600nm to 770nm were obtained by varying the processing conditions. They were characterized in terms of thermal and dynamical mechanical properties, swelling degree and morphology. The elastomeric polyurethane scaffolds exhibit interesting properties that could be appropriate as biomimetic matrices for soft tissue engineering applications. Copyright © 2015 Elsevier B.V. All rights reserved.

A novel approach for synthesis of zwitterionic polyurethane coating with protein resistance.

PubMed

Wang, Chunhua; Ma, Chunfeng; Mu, Changdao; Lin, Wei

2014-11-04

We have developed a novel approach to introduce zwitterions into polyurethane for the preparation of antibiofouling coating. First, the thiol-ene click reaction between 2-(dimethylamino)ethyl methacrylate (DMAEMA) and 3-mercapto-1,2-propanediol (TPG) is used to synthesize dihydroxy-terminated DMAEMA (DMA(OH)2) under UV catalysis. The product has been proved by gel permeation chromatography (GPC), Fourier transform infrared spectrum (FT-IR), proton nuclear magnetic resonance ((1)H NMR), and high resolution mass spectrometry (HRMS). DMA(OH)2 is then incorporated into polyurethane as side groups by polyaddition with diisocyanate and further reacts with 1,3-propane sultone to obtain the zwitterionic polyurethanes. The presence of sulfobetaine zwitterions side groups has been demonstrated by FT-IR and X-ray photoelectron spectroscopy (XPS). Thermal analysis indicates that the thermal stability is decreased with the increasing content of zwitterionions. The antibiofouling property of polyurethanes has been investigated by the measurement of adsorption of fibrinogen, bovine serum albumin (BSA), and lysozyme on the polyurethanes surface using quartz crystal microbalance with dissipation (QCM-D). The results show that the polyurethane coatings exhibit effective nonspecific protein resistance at higher content of zwitterionic side groups.

Enhancement of mechanical properties of epoxy/graphene nanocomposite

NASA Astrophysics Data System (ADS)

Berhanuddin, N. I. C.; Zaman, I.; Rozlan, S. A. M.; Karim, M. A. A.; Manshoor, B.; Khalid, A.; Chan, S. W.; Meng, Q.

2017-10-01

Graphene is a novel class of nanofillers possessing outstanding characteristics including most compatible with most polymers, high absolute strength, high aspect ratio and cost effectiveness. In this study, graphene was used to reinforce epoxy as a matrix, to enhance its mechanical properties. Two types of epoxy composite were developed which are epoxy/graphene nanocomposite and epoxy/modified graphene nanocomposite. The fabrication of graphene was going through thermal expansion and sonication process. Chemical modification was only done for modified graphene where 4,4’-Methylene diphenyl diisocyanate (MDI) is used. The mechanical properties of both nanocomposite, such as Young’s modulus and maximum stress were investigated. Three weight percentage were used for this study which are 0.5 wt%, 1.0 wt% and 1.5 wt%. At 0.5 wt%, modified and unmodified shows the highest value compared to neat epoxy, where the value were 8 GPa, 6 GPa and 0.675 GPa, respectively. For maximum stress, neat epoxy showed the best result compared to both nanocomposite due to the changes of material properties when adding the filler into the matrix. Therefore, both nanocomposite increase the mechanical properties of the epoxy, however modification surface of graphene gives better improvement.

Reactive decomposition of low density PMDI foam subject to shock compression

NASA Astrophysics Data System (ADS)

Alexander, Scott; Reinhart, William; Brundage, Aaron; Peterson, David

Low density polymethylene diisocyanate (PMDI) foam with a density of 5.4 pounds per cubic foot (0.087 g/cc) was tested to determine the equation of state properties under shock compression over the pressure range of 0.58 - 3.4 GPa. This pressure range encompasses a region approximately 1.0-1.2 GPa within which the foam undergoes reactive decomposition resulting in significant volume expansion of approximately three times the volume prior to reaction. This volume expansion has a significant effect on the high pressure equation of state. Previous work on similar foam was conducted only up to the region where volume expansion occurs and extrapolation of that data to higher pressure results in a significant error. It is now clear that new models are required to account for the reactive decomposition of this class of foam. The results of plate impact tests will be presented and discussed including details of the unique challenges associated with shock compression of low density foams. Sandia National Labs is a multi-program lab managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corp., for the U.S. Dept. of Energy's National Nuclear Security Administration under Contract DE-AC04-94AL85000.

Occupational asthma in a steel coating plant.

PubMed

Venables, K M; Dally, M B; Burge, P S; Pickering, C A; Newman Taylor, A J

1985-08-01

An outbreak of occupational asthma, of unknown cause and extent, was detected in a steel coating plant. In 1979 a cross-sectional study which defined occupational asthma in terms of respiratory symptoms detected 21 people with suggestive symptoms among the 221 studied. They all worked in the coating shop, but the plastic coatings used at the plant contained many potential sensitising agents that might have caused the asthma. All 21 developed their symptoms after 1971, and it was found that in this year a supplier had modified a coating allowing, at the temperatures used in the process, toluene di-isocyanate to be liberated. Two of the symptomatic subjects were tested by inhalation of the isocyanate and showed asthmatic reactions and other subjects were found to have asthma related to periods spent at work by records of peak expiratory flow rate. Over half the 21 had a symptom free latent period after first exposure of three years or less, a pattern not seen in other subjects with respiratory symptoms. After the isocyanate had been removed from the process 17 of these subjects became asymptomatic or improved, a greater proportion than in other subjects with respiratory symptoms.

N-halamine-based rechargeable antimicrobial and biofilm-controlling polyurethane

PubMed Central

Sun, Xinbo; Cao, Zhengbing; Porteous, Nuala; Sun, Yuyu

2012-01-01

An N-halamine precursor, 5, 5-dimethyl hydantoin (DMH), was covalently linked to the surface of polyurethane (PU) with 1,6-hexamethylene diisocyanate (HDI) as a coupling agent. The reaction pathways were investigated using propyl isocyanate (PI) as a model compound, and the results suggested that the imide and amide groups of DMH had very similar reactivity toward the isocyanate groups on PU surfaces activated with HDI. After bleach treatment, the covalently bound DMH moieties were transformed into N-halamines. The new N-halmaine-based PU provided potent antimicrobial effects against Staphylococcus aureus (S. aureus, Gram-positive), Escherichia coli (E. coli, Gram-negative), methicillin-resistant staphylococcus aureus (MRSA, drug resistant Gram-positive bacteria), vancomycin-resistant enterococcus (VRE, drug resistant Gram-positive bacteria), and Candida albicans (C. ablicans, fungi), and successfully prevented bacterial and fungal biofilm formation. The antimicrobial and biofilm-controlling effects were stable for longer than 6 months under normal storage in open air. Furthermore, if the functions were lost due to prolonged use, they could be recharged by another chlorination treatment. The recharging could be repeated as needed to achieve long-term protection against microbial contamination and biofilm-formation. PMID:22244984

[Research on structure of MC-nylon 6/aramid composites by spectroanalysis method].

PubMed

Wang, Can-Yao; Zheng, Yu-Ying

2008-01-01

The Kevlar fiber, treated with toluene-2,4-diisocyanate and caprolactam, was used to reinforce MC nylon 6. XPS showed the change in chemical components and spectra after fiber was treated. IR showed that the spectra of Kevlar fiber and MC-nylon 6 were incorporated purely when they were mixed, while the treated Kevlar fiber provided the activation in the ring-opening polymerization of caprolactam, and the amide groups of graft chains could form strong hydrogen bonds with matrix. These graft chains and hydrogen bonds would contribute to improving interfacial bonding between MC-nylon 6 and Kevlar fiber. XRD indicated that the induction of Kevlar fiber had no effect on the cryastalline style of MC-nylon 6 obviously, however, the crystals had better seasonal structure. The crystals of MC-nylon 6/Kevlar fiber composites were more perfect than that of MC-nylon 6/Kevlar untreated fiber composites with the same amount of Kevlar fiber. The increase of Kevlar fiber contributed to forming perfect a spherulite when the mass concentration of Kevlar fiber was less than 2%, however, the more the Kevlar fiber, the less the content of a spherulite when the mass concentration of Kevlar fiber was more than 2%.

Occupational allergic and irritant contact dermatitis in workers exposed to polyurethane foam.

PubMed

Kieć-Świerczyńska, Marta; Swierczyńska-Machura, Dominika; Chomiczewska-Skóra, Dorota; Nowakowska-Świrta, Ewa; Kręcisz, Beata

2014-04-01

To evaluate sensitization to chemicals present in work environment after an outbreak of contact dermatitis in workers of vehicle equipment factory, exposed to polyurethane foam, based on 4,4'-diphenylmethane diisocyanate (MDI). From among 300 employees, 21 individuals reporting work-related skin and/or respiratory tract symptoms underwent clinical examination, patch testing, skin prick tests, spirometry and MDI sIgE measurement in serum. Patch tests included isocyanates series, selected rubber additives, metals, fragrances, preservatives, and an antiadhesive agent. Clinical examination revealed current eczema in the area of hands and/or forearms in 10 workers. Positive patch test reactions were found in 10 individuals, the most frequent to diaminodiphenylmethane and 4-phenylenediamine (7 persons). Reactions to an antiadhesive agent were assessed as irritant (5 workers). Except for sensitization to common aeroallergens, no significant abnormalities were found in the remaining tests. Occupational allergic contact dermatitis was diagnosed in 7 workers, irritant contact dermatitis in 10 and coexisiting allergic and irritant contact dermatitis in 3 workers. In workers manufacturing products from polyurethane foam, attention should be paid to the risk of developing contact dermatitis. Skin problems in our study group were attributable probably to insufficient protection of the skin.

Gelatin-Modified Polyurethanes for Soft Tissue Scaffold

PubMed Central

Kucińska-Lipka, Justyna; Janik, Helena

2013-01-01

Recently, in the field of biomaterials for soft tissue scaffolds, the interest of their modification with natural polymersis growing. Synthetic polymers are often tough, and many of them do not possess fine biocompatibility. On the other hand, natural polymers are biocompatible but weak when used alone. The combination of natural and synthetic polymers gives the suitable properties for tissue engineering requirements. In our study, we modified gelatin synthetic polyurethanes prepared from polyester poly(ethylene-butylene adipate) (PEBA), aliphatic 1,6-hexamethylene diisocyanate (HDI), and two different chain extenders 1,4-butanediol (BDO) or 1-ethoxy-2-(2-hydroxyethoxy)ethanol (EHEE). From a chemical point of view, we replaced expensive components for building PU, such as 2,6-diisocyanato methyl caproate (LDI) and 1,4-diisocyanatobutane (BDI), with cost-effective HDI. The gelatin was added in situ (in the first step of synthesis) to polyurethane to increase biocompatibility and biodegradability of the obtained material. It appeared that the obtained gelatin-modified PU foams, in which chain extender was BDO, had enhanced interactions with media and their hydrolytic degradation profile was also improved for tissue engineering application. Furthermore, the gelatin introduction had positive impact on gelatin-modified PU foams by increasing their hemocompatibility. PMID:24363617

Mortality among workers exposed to toluene diisocyanate in the US polyurethane foam industry: Update and exposure-response analyses.

PubMed

Pinkerton, Lynne E; Yiin, James H; Daniels, Robert D; Fent, Kenneth W

2016-08-01

Mortality among 4,545 toluene diisocyante (TDI)-exposed workers was updated through 2011. The primary outcome of interest was lung cancer. Life table analyses, including internal analyses by exposure duration and cumulative TDI exposure, were conducted. Compared with the US population, all cause and all cancer mortality was increased. Lung cancer mortality was increased but was not associated with exposure duration or cumulative TDI exposure. In post hoc analyses, lung cancer mortality was associated with employment duration in finishing jobs, but not in finishing jobs involving cutting polyurethane foam. Dermal exposure, in contrast to inhalational exposure, to TDI is expected to be greater in finishing jobs and may play a role in the observed increase in lung cancer mortality. Limitations include the lack of smoking data, uncertainty in the exposure estimates, and exposure estimates that reflected inhalational exposure only. Am. J. Ind. Med. 59:630-643, 2016. Published 2016. This article is a U.S. Government work and is in the public domain in the USA. Published 2016. This article is a U.S. Government work and is in the public domain in the USA.

Green waste cooking oil-based rigid polyurethane foam

NASA Astrophysics Data System (ADS)

Enderus, N. F.; Tahir, S. M.

2017-11-01

Polyurethane is a versatile polymer traditionally prepared using petroleum-based raw material. Petroleum, however, is a non-renewable material and polyurethane produced was found to be non-biodegradable. In quest for a more environmentally friendly alternative, wastecooking oil, a highly abundant domestic waste with easily derivatized structure, is a viable candidate to replace petroleum. In this study,an investigation to determine physical and chemical properties of rigid polyurethane (PU) foam from waste cooking oil (WCO) was carried out. WCO was first adsorbed by using coconut husk activated carbon adsorbent prior to be used for polyol synthesis. The purified WCO was then used to synthesize polyol via transesterification reaction to yield alcohol groups in the WCO chains structure. Finally, the WCO-based polyol was used to prepare rigid PU foam. The optimum formulation for PU formation was found to be 90 polyol: 60 glycerol: 54 water: 40 diethanolamine: 23 diisocyanate. The rigid PU foam has density of 208.4 kg/m3 with maximum compressive strength and capability to receive load at 0.03 MPa and 0.09 kN, respectively. WCO-based PU can potentially be used to replace petroleum-based PU as house construction materials such as insulation panels.

Synthesis of highly elastic biocompatible polyurethanes based on bio-based isosorbide and poly(tetramethylene glycol) and their properties

PubMed Central

Kim, Hyo-Jin; Kang, Min-Sil; Knowles, Jonathan C

2014-01-01

Bio-based high elastic polyurethanes were prepared from hexamethylene diisocyanate and various ratios of isosorbide to poly(tetramethylene glycol) as a diol by a simple one-shot bulk polymerization without a catalyst. Successful synthesis of the polyurethanes was confirmed by Fourier transform-infrared spectroscopy and 1H nuclear magnetic resonance. Thermal properties were determined by differential scanning calorimetry and thermogravimetric analysis. The glass transition temperature was −47.8℃. The test results showed that the poly(tetramethylene glycol)/isosorbide-based elastomer exhibited not only excellent stress–strain properties but also superior resilience to the existing polyether-based polyurethane elastomers. The static and dynamic properties of the polyether/isosorbide-based thermoplastic elastomer were more suitable for dynamic applications. Moreover, such rigid diols impart biocompatible and bioactive properties to thermoplastic polyurethane elastomers. Degradation tests performed at 37℃ in phosphate buffer solution showed a mass loss of 4–9% after 8 weeks, except for the polyurethane with the lowest isosorbide content, which showed an initial rapid weight loss. These polyurethanes offer significant promise due to soft, flexible and biocompatible properties for soft tissue augmentation and regeneration. PMID:24812276

Tunable Elastomers with an Antithrombotic Component for Cardiovascular Applications.

PubMed

Stahl, Alexander M; Yang, Yunzhi Peter

2018-05-31

This study reports the development of a novel family of biodegradable polyurethanes for use as tissue engineered cardiovascular scaffolds or blood-contacting medical devices. Covalent incorporation of the antiplatelet agent dipyridamole into biodegradable polycaprolactone-based polyurethanes yields biocompatible materials with improved thromboresistance and tunable mechanical strength and elasticity. Altering the ratio of the dipyridamole to the diisocyanate linking unit and the polycaprolactone macromer enables control over both the drug content and the polymer cross-link density. Covalent cross-linking in the materials achieves significant elasticity and a tunable range of elastic moduli similar to that of native cardiovascular tissues. Interestingly, the cross-link density of the polyurethanes is inversely related to the elastic modulus, an effect attributed to decreasing crystallinity in the more cross-linked polymers. In vitro characterization shows that the antiplatelet agent is homogeneously distributed in the materials and is released slowly throughout the polymer degradation process. The drug-containing polyurethanes support endothelial cell and vascular smooth muscle cell proliferation, while demonstrating reduced levels of platelet adhesion and activation, supporting their candidacy as promising substrates for cardiovascular tissue engineering. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A novel bioactive osteogenesis scaffold delivers ascorbic acid, β-glycerophosphate, and dexamethasone in vivo to promote bone regeneration.

PubMed

Wang, Chao; Cao, Xuecheng; Zhang, Yongxian

2017-05-09

Ascorbic acid, β-glycerophosphate, and dexamethasone have been used in osteogenesis differentiation medium for in vitro cell culture, nothing is known for delivering these three bioactive compounds in vivo. In this study, we synthesized a novel bioactive scaffold by combining these three compounds with a lysine diisocyanate-based polyurethane. These bioactive compounds were released from the scaffold during the degradation process. The cell culture showed that the sponge-like structure in the scaffold was critical in providing a large surface area to support cell growth and all degradation products of the polymer were non-toxic. This bioactive scaffold enhanced the bone regeneration as evidenced by increasing the expression of three bone-related genes including collagen type I, Runx-2 and osteocalcin in rabbit bone marrow stem cells (BMSCs) in vitro and in vivo. The osteogenesis differentiation of BMSCs cultured in this bioactive scaffold was similar to that in osteogenesis differentiation medium and more extensive in this bioactive scaffold compared to the scaffold without these three bioactive compounds. These results indicated that the scaffold containing three bioactive compounds was a good osteogenesis differentiation promoter to enhance the osteogenesis differentiation and new bone formation in vivo.

A novel bioactive osteogenesis scaffold delivers ascorbic acid, β-glycerophosphate, and dexamethasone in vivo to promote bone regeneration

PubMed Central

Wang, Chao; Cao, Xuecheng; Zhang, Yongxian

2017-01-01

Ascorbic acid, β-glycerophosphate, and dexamethasone have been used in osteogenesis differentiation medium for in vitro cell culture, nothing is known for delivering these three bioactive compounds in vivo. In this study, we synthesized a novel bioactive scaffold by combining these three compounds with a lysine diisocyanate-based polyurethane. These bioactive compounds were released from the scaffold during the degradation process. The cell culture showed that the sponge-like structure in the scaffold was critical in providing a large surface area to support cell growth and all degradation products of the polymer were non-toxic. This bioactive scaffold enhanced the bone regeneration as evidenced by increasing the expression of three bone-related genes including collagen type I, Runx-2 and osteocalcin in rabbit bone marrow stem cells (BMSCs) in vitro and in vivo. The osteogenesis differentiation of BMSCs cultured in this bioactive scaffold was similar to that in osteogenesis differentiation medium and more extensive in this bioactive scaffold compared to the scaffold without these three bioactive compounds. These results indicated that the scaffold containing three bioactive compounds was a good osteogenesis differentiation promoter to enhance the osteogenesis differentiation and new bone formation in vivo. PMID:28404942

α-Amylase sensor based on the degradation of oligosaccharide hydrogel films monitored with a quartz crystal sensor.

PubMed

Gibbs, Martin John; Biela, Anna; Krause, Steffi

2015-05-15

α-Amylase hydrolyses starch molecules to produce smaller oligosaccharides and sugars. Amylases are of great importance in biotechnology and find application in fermentation, detergents, food and the paper industry. The measurement of α-amylase activity in serum and urine has been used in the diagnosis of acute pancreatitis. Salivary amylase has also been shown to be a stress indicator. Sensor coatings suitable for the detection of α-amylase activity have been developed. Oligosaccharides such as glycogen and amylopectin were spin-coated onto gold coated quartz crystals with a base frequency of 10 MHz. The films were subsequently cross-linked with hexamethylene diisocyanate. Film degradation was monitored with a quartz crystal microbalance (QCM) and electrochemical impedance measurements. The films were shown to be stable in phosphate buffered saline (PBS). Addition of α-amylase to the solution resulted in the rapid degradation of the films. The maximum rate of degradation was found to be strongly dependent on the amylase activity in the range typically found in serum when diagnosing pancreatitis (0.08-8 U/ml). Sensor responses in serum were found to be very similar to those obtained in buffer indicating the absence of non-specific binding. Copyright © 2014 Elsevier B.V. All rights reserved.

A novel surface modification of carbon fiber for high-performance thermoplastic polyurethane composites

NASA Astrophysics Data System (ADS)

Zhang, Yuanyuan; Zhang, Yizhen; Liu, Yuan; Wang, Xinling; Yang, Bin

2016-09-01

Properties of carbon fiber (CF) reinforced composites depend largely on the interfacial bonding strength between fiber and the matrix. In the present work, CF was grafted by 4,4‧-diphenylmethane diisocyanate (MDI) molecules after electrochemical oxidation treatment. The existence of functional groups introduced to the fiber surface and the changes of surface roughness were confirmed by FTIR, AFM, XPS, SEM and Raman spectroscopy. To evaluate the possible applications of this surface modification of carbon fiber, we examined the mechanical properties as well as the friction and wear performance of pristine CF and MDI-CF reinforced thermoplastic polyurethane (TPU) composites with 5-30 wt.% fiber contents, and found that the mechanical properties of TPU composites were all significantly improved. It is remarkable that when fiber content was 30 wt.%, the tensile strength of TPU/MDI-CF was increased by 99.3%, which was greater than TPU/CF (53.2%), and the friction loss of TPU/MDI-CF was decreased by 49.09%. The results of DMA and SEM analysis indicated the positive effects of MDI modification on the interfacial bonding between fibers and matrix. We believed that this simple and effective method could be used to the development of surface modified carbon fiber for high-performance TPU.

Synthesis and properties of shape memory polyurethanes generated from schiff-base chain extender containing benzoyl and pyridyl rings

PubMed Central

Weng, Neng-Chiao; Wu, Chih-Fu; Tsen, Wen-Chin; Wu, Cheng-Lung; Suen, Maw-Cherng

2018-01-01

Abstract In this study, 4,4′-diphenylmethane diisocyanate and polytetramethylene glycol were used to prepare a prepolymer; N,N′-bis(4-hydroxybenzylidene)-2,6-diaminopyridine (BHBP) was used as a chain extender; and these elements were combined to prepare a novel polyurethane, BHBP/PU. Gel permeation chromatography revealed that the molecular weight of the BHBP/PU samples increased as the BHBP content was increased. Fourier transform infrared spectroscopy demonstrated that high BHBP content facilitated strong hydrogen bonding in the samples. Differential thermogravimetry indicated that the initial decomposition temperature of BHBP/PU-3 was approximately 10 °C higher than that of BHBP/PU-1. Differential scanning calorimetry and dynamic mechanical analysis revealed that increasing the BHBP content substantially increased both the glass transition and dynamic glass transition temperatures of the BHBP/PU samples. The tensile strengths of BHBP/PU-1, BHBP/PU-2, and BHBP/PU-3 were 7.7, 10.9, and 21.6 MPa, respectively, with corresponding Young’s moduli of 0.7, 1.9, and 3.3 MPa. These results demonstrated that both the tensile strength and Young’s modulus of the BHBP/PU samples increased as the BHBP content was increased. Moreover, the BHBP/PU samples exhibited excellent shape recovery of >90%. PMID:29706848

Glutathione-mediated biodegradable polyurethanes derived from L-arabinitol.

PubMed

de Paz, M Violante; Zamora, Francisca; Begines, Belén; Ferris, Cristina; Galbis, Juan A

2010-01-11

The synthesis, characterization, and some properties of new glutathione-mediated biodegradable sugar-based copolyurethanes are described. These copolyurethanes were obtained by polyaddition reaction of mixtures of 2,2'-dithiodiethanol (DiT) and 2,3,4-tri-O-benzyl-L-arabinitol (ArBn) or 2,3,4-tri-O-methyl-L-arabinitol (ArMe) to 1,6-hexamethylene diisocyanate (HMDI). The copolymer compositions were studied by elemental microanalyses and (1)H NMR, revealing that the content of the copolymer units is in all cases very similar to that of their corresponding feed. The PU(DiT-HMDI) homopolymer exhibited a high crystallinity, but the introduction of the arabinitol-based diols led to a reduction in the crystallinity of the copolymers. In their TG curves, the copolymers exhibited a mixed trend of the related homopolymers, and all of them were thermally stable, with degradation temperatures above 220 degrees C. The degradation properties of the macromolecules under physiological conditions in the presence of glutathione were tested. All the copolyurethanes proved to be biodegradable under the experimental conditions (pH = 7.02 and 37 degrees C). The degradation pattern of the copolymers depended not only on the dithiodiethanol (DiT) reactive units ratio in the polymer backbone, but also on the crystallinity of the macromolecule.

A Novel Polar Copolymer Design as a Multi-Functional Binder for Strong Affinity of Polysulfides in Lithium-Sulfur Batteries

NASA Astrophysics Data System (ADS)

Jiao, Yu; Chen, Wei; Lei, Tianyu; Dai, Liping; Chen, Bo; Wu, Chunyang; Xiong, Jie

2017-03-01

High energy density, low cost and environmental friendliness are the advantages of lithium-sulfur (Li-S) battery which is regarded as a promising device for electrochemical energy storage systems. As one of the important ingredients in Li-S battery, the binder greatly affects the battery performance. However, the conventional binder has some drawbacks such as poor capability of absorbing hydrophilic lithium polysulfides, resulting in severe capacity decay. In this work, we reported a multi-functional polar binder (AHP) by polymerization of hexamethylene diisocyanate (HDI) with ethylenediamine (EDA) bearing a large amount of amino groups, which were successfully used in electrode preparation with commercial sulfur powder cathodes. The abundant amide groups of the binder endow the cathode with multidimensional chemical bonding interaction with sulfur species within the cathode to inhibit the shuttling effect of polysulfides, while the suitable ductility to buffer volume change. Utilizing these advantageous features, composite C/S cathodes based the binder displayed excellent capacity retention at 0.5 C, 1 C, 1.5 C, and 3 C over 200 cycles. Accompany with commercial binder, AHP may act as an alternative feedstock to open a promising approach for sulfur cathodes in rechargeable lithium battery to achieve commercial application.

Synthesis and bioimaging of biodegradable red fluorescent organic nanoparticles with aggregation-induced emission characteristics.

PubMed

Xu, Dazhuang; Zou, Hui; Liu, Meiying; Tian, Jianwen; Huang, Hongye; Wan, Qing; Dai, Yanfeng; Wen, Yuanqing; Zhang, Xiaoyong; Wei, Yen

2017-12-15

Fluorescent organic nanoparticles (FONs) with aggregation-induced emission (AIE) features have recently emerged as promising fluorescent probes for biomedical applications owing to their excellent optical properties, designability and biocompatibility. Significant progress has been made recently for synthesis and biomedical applications of these AIE-active FONs. However, only very limited reports have demonstrated the fabrication of biodegradable AIE-active FONs with red fluorescence emission. In this study, a novel strategy has been developed for the preparation of biodegradable AIE-active polyurethanes (PUs) through a two-step polymerization, in which the diisocyanate-terminated polyethylene glycol (NCO-PEG-NCO) was synthesized and subsequently conjugated with diamine-containing AIE dye (NH 2 -Phe-NH 2 ). The successful synthesis of AIE-active Phe-PEG 2000 PUs is evidenced by a series of characterization techniques. Because of the formation of AIE-active amphiphilic PUs, the final copolymers can self-assemble into spherical nanoparticles, which exhibit strong luminescence and high water dispersion. The biological evaluation results suggest that the AIE-active Phe-PEG 2000 FONs possess low toxicity and desirable cell permeability. Therefore, we anticipate that these AIE-active FONs with biodegradable potential will trigger much research enthusiasm and effort toward the creation of new AIE-active materials with improved properties for various biomedical applications. Copyright © 2017 Elsevier Inc. All rights reserved.

3D-Hydrogel Based Polymeric Nanoreactors for Silver Nano-Antimicrobial Composites Generation.

PubMed

Soto-Quintero, Albanelly; Romo-Uribe, Ángel; Bermúdez-Morales, Víctor H; Quijada-Garrido, Isabel; Guarrotxena, Nekane

2017-08-01

This study underscores the development of Ag hydrogel nanocomposites, as smart substrates for antibacterial uses, via innovative in situ reactive and reduction pathways. To this end, two different synthetic strategies were used. Firstly thiol-acrylate (PSA) based hydrogels were attained via thiol-ene and radical polymerization of polyethylene glycol (PEG) and polycaprolactone (PCL). As a second approach, polyurethane (PU) based hydrogels were achieved by condensation polymerization from diisocyanates and PCL and PEG diols. In fact, these syntheses rendered active three-dimensional (3D) hydrogel matrices which were used as nanoreactors for in situ reduction of AgNO₃ to silver nanoparticles. A redox chemistry of stannous catalyst in PU hydrogel yielded spherical AgNPs formation, even at 4 °C in the absence of external reductant; and an appropriate thiol-functionalized polymeric network promoted spherical AgNPs well dispersed through PSA hydrogel network, after heating up the swollen hydrogel at 103 °C in the presence of citrate-reductant. Optical and swelling behaviors of both series of hydrogel nanocomposites were investigated as key factors involved in their antimicrobial efficacy over time. Lastly, in vitro antibacterial activity of Ag loaded hydrogels exposed to Pseudomona aeruginosa and Escherichia coli strains indicated a noticeable sustained inhibitory effect, especially for Ag-PU hydrogel nanocomposites with bacterial inhibition growth capabilities up to 120 h cultivation.

Producing Lignin-Based Polyols through Microwave-Assisted Liquefaction for Rigid Polyurethane Foam Production

PubMed Central

Xue, Bai-Liang; Wen, Jia-Long; Sun, Run-Cang

2015-01-01

Lignin-based polyols were synthesized through microwave-assisted liquefaction under different microwave heating times (5–30 min). The liquefaction reactions were carried out using polyethylene glycol (PEG-400)/glycerol as liquefying solvents and 97 wt% sulfur acid as a catalyst at 140 °C. The polyols obtained were analyzed for their yield, composition and structural characteristics using gel permeation chromatography (GPC), Fourier transform infrared (FT-IR) and nuclear magnetic resonance (NMR) spectra. FT-IR and NMR spectra showed that the liquefying solvents reacted with the phenol hydroxyl groups of the lignin in the liquefied product. With increasing microwave heating time, the viscosity of polyols was slightly increased and their corresponding molecular weight (MW) was gradually reduced. The optimal condition at the microwave heating time (5 min) ensured a high liquefaction yield (97.47%) and polyol with a suitable hydroxyl number (8.628 mmol/g). Polyurethane (PU) foams were prepared by polyols and methylene diphenylene diisocyanate (MDI) using the one-shot method. With the isocyanate/hydroxyl group ([NCO]/[OH]) ratio increasing from 0.6 to 1.0, their mechanical properties were gradually increased. This study provided some insight into the microwave-assisted liquefied lignin polyols for the production of rigid PU foam. PMID:28787959

Toluene diisocyanate based phase-selective supramolecular oil gelator for effective removal of oil spills from polluted water.

PubMed

Wang, Yongzhen; Wang, Youshan; Yan, Xingru; Wu, Songquan; Shao, Lu; Liu, Yuyan; Guo, Zhanhu

2016-06-01

Due to tremendous resource wastes and great harm to ecological environment caused by the accidental oil spills, an alkyl bicarbamate supramolecular oil gelator was synthesized and applied to selectively gelate oils from oil/water mixtures. Interestingly, the oil gelator could be self-assembled in a series of organic solvents, i.e., edible oils and fuel oils to form 3D networks and then turned into thermally reversible organogels, allowing easy separation and removal of oil spills from oil/water mixtures. The possible self-assembly mode for the formation of organogels was proposed. What's more, the optimal conditions for using the oil gelator to recover oils were experimentally determined. Inspiringly, taking gasoline as the co-congealed solvent, a complete gelation of oil phase was achieved within 15 min with high oil removal rate and oil retention rate after convenient salvage and cleanup of oil gels from oil/water mixtures. The oil gelator had some advantages in solidifying oil spills on water surface, exhibiting fast oil gelation, convenient and thorough oil removal and easy recovery. This work illustrates the significant role of oil gelators in the potential cleanup of spilled oils for water purification. Copyright © 2016 Elsevier Ltd. All rights reserved.

Remediation of hydrocarbons polluted water by hydrophobic functionalized cellulose.

PubMed

Tursi, Antonio; Beneduci, Amerigo; Chidichimo, Francesco; De Vietro, Nicoletta; Chidichimo, Giuseppe

2018-06-01

Remediation of water bodies from petroleum hydrocarbons is of the utmost importance due to health risks related to the high toxicity, mutagenicity and carcinogenicity of the hydrocarbons components that may enter into the food chain. Though several methods were proposed to face up this challenge, they are generally not easily feasible at a contaminated site and quite costly. Here we propose a green, cost-effective technology based on hydrophobized Spanish Broom (SB) cellulose fiber. The natural cellulose fiber was extracted by alkaline digestion of the raw vegetable. The hydrophilic cellulose surface was transformed into a hydrophobic one by the reaction with 4,4'-diphenylmethane diisocyanate (MDI) forming a very stable urethane linkage with the hydroxyl groups of cellulose emerging from the fibers surface. Chemical functionalization was performed with a novel solvent-free technology based on a home-made still reactor were the fiber was kept under vortex stirring and the MDI reactant then spread onto the fiber surface by nebulizing it in form of micrometer-sized droplets. The functionalized fiber, characterized by means of WCA measurements, XPS and ATR-FTIR spectroscopy, shows fast adsorption kinetics adsorption capacity as high as 220 mg/g, among the highest ever reported so far in the literature for cellulosic materials. Copyright © 2018 Elsevier Ltd. All rights reserved.

Synthesis of highly elastic biocompatible polyurethanes based on bio-based isosorbide and poly(tetramethylene glycol) and their properties.

PubMed

Kim, Hyo-Jin; Kang, Min-Sil; Knowles, Jonathan C; Gong, Myoung-Seon

2014-09-01

Bio-based high elastic polyurethanes were prepared from hexamethylene diisocyanate and various ratios of isosorbide to poly(tetramethylene glycol) as a diol by a simple one-shot bulk polymerization without a catalyst. Successful synthesis of the polyurethanes was confirmed by Fourier transform-infrared spectroscopy and (1)H nuclear magnetic resonance. Thermal properties were determined by differential scanning calorimetry and thermogravimetric analysis. The glass transition temperature was -47.8℃. The test results showed that the poly(tetramethylene glycol)/isosorbide-based elastomer exhibited not only excellent stress-strain properties but also superior resilience to the existing polyether-based polyurethane elastomers. The static and dynamic properties of the polyether/isosorbide-based thermoplastic elastomer were more suitable for dynamic applications. Moreover, such rigid diols impart biocompatible and bioactive properties to thermoplastic polyurethane elastomers. Degradation tests performed at 37℃ in phosphate buffer solution showed a mass loss of 4-9% after 8 weeks, except for the polyurethane with the lowest isosorbide content, which showed an initial rapid weight loss. These polyurethanes offer significant promise due to soft, flexible and biocompatible properties for soft tissue augmentation and regeneration. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Structure-Property Relationships in Porous 3-D Nanostructures as a Function of Preparation Conditions: Isocyanate Cross-Linked Silica Aerogels

NASA Technical Reports Server (NTRS)

Meador, Mary Ann B.; Capadona, Lynn A.; McCorkle, Linda; Padadopoulos, Demetrios S.; Leventis, Nicholas

2007-01-01

Sol-gel derived silica aerogels are attractive candidates for many unique thermal, optical, catalytic, and chemical applications because of their low density and high mesoporosity. However, their inherent fragility has restricted use of aerogel monoliths to applications where they are not subject to any load. We have previously reported cross-linking the mesoporous silica structure of aerogels with di-isocyanates, styrenes or epoxies reacting with amine decorated silica surfaces. These approaches have been shown to significantly increase the strength of aerogels with only a small effect on density or porosity. Though density is a prime predictor of properties such as strength and thermal conductivity for aerogels, it is becoming clear from previous studies that varying the silica backbone and size of the polymer cross-link independently can give rise to combinations of properties which cannot be predicted from density alone. Herein, we examine the effects of four processing parameters for producing this type of polymer cross-linked aerogel on properties of the resulting monoliths. We focus on the results of C-13 CP-MAS NMR which gives insight to the size and structure of polymer cross-link present in the monoliths, and relates the size of the cross-links to microstructure, mechanical properties and other characteristics of the materials obtained.

Structure-Property Relationships in Porous 3-D Nanostructures as a Function of Preparation Conditions: Isocyanate Cross-Linked Silica Aerogels

NASA Technical Reports Server (NTRS)

Meador, Mary Ann B.; Capadona, Lynn A.; McCorkle, Linda; Papadopoulos, Demetrios S.; Leventis, Nicholas

2007-01-01

Sol-gel derived silica aerogels are attractive candidates for many unique thermal, optical, catalytic, and chemical applications because of their low density and high mesoporosity. However, their inherent fragility has restricted use of aerogel monoliths to applications where they are not subject to any load. We have previously reported cross-linking the mesoporous silica structure of aerogels with di-isocyanates, styrenes or epoxies reacting with amine decorated silica surfaces. These approaches have been shown to significantly increase the strength of aerogels with only a small effect on density or porosity. Though density is a prime predictor of properties such as strength and thermal conductivity for aerogels, it is becoming clear from previous studies that varying the silica backbone and size of the polymer cross-link independently can give rise to combinations of properties which cannot be predicted from density alone. Herein, we examine the effects of four processing parameters for producing this type of polymer cross-linked aerogel on properties of the resulting monoliths. We focus on the results of 13C CP-MAS NMR which gives insight to the size and structure of polymer cross-link present in the monoliths, and relates the size of the cross-links to microstructure, mechanical properties and other characteristics of the materials obtained.

Isocyanate Exposure Below Analytical Detection When a Paint Brush and Roller Are Used to Apply Moisture-Cure Polyurethane Paint.

PubMed

Reeb-Whitaker, Carolyn K; Schoonover, Todd M

2016-05-01

Isocyanate exposure is known to be hazardous when polyurethane paints are applied with a spray gun, but less is known of exposure when paint is applied with a paint brush and roller. Concentrations of 1,6-hexamethylene diisocyanate (HDI) monomer and three HDI polymers were assessed when two moisture-cure polyurethane paints containing 31-35% isocyanates were applied with a paint roller and brush. Short-term 15-min samples were taken during paint application in an indoor test environment with no ventilation (n= 12); in an outdoor test environment (n= 11); and in an outdoor in-situ assessment (n= 22). The outdoor in-situ assessment involved the painting of a bus shelter and light poles at a public transit station over two night shifts. All isocyanate samples were below analytical detection. The analytical limits of detection for HDI monomer, HDI biuret, HDI isocyanurate, and HDI uretdione were 0.005, 0.84, 0.87, and 0.88 µg, respectively. The finding that isocyanate concentrations were below detection is attributed to the use of paint roller and brush which minimize paint aerosolization and the paint formulation itself which contained <1% of volatile HDI monomer. © The Author 2016. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Biocompatibility and inflammatory response in vitro and in vivo to gelatin-based biomaterials with tailorable elastic properties.

PubMed

Ullm, Sandra; Krüger, Anne; Tondera, Christoph; Gebauer, Tim P; Neffe, Axel T; Lendlein, Andreas; Jung, Friedrich; Pietzsch, Jens

2014-12-01

Hydrogels prepared from gelatin and lysine diisocyanate ethyl ester provide tailorable elastic properties and degradation behavior. Their interaction with human aortic endothelial cells (HAEC) as well as human macrophages (Mɸ) and granulocytes (Gɸ) were explored. The experiments revealed a good biocompatibility, appropriate cell adhesion, and cell infiltration. Direct contact to hydrogels, but not contact to hydrolytic or enzymatic hydrogel degradation products, resulted in enhanced cyclooxygenase-2 (COX-2) expression in all cell types, indicating a weak inflammatory activation in vitro. Only Mɸ altered their cytokine secretion profile after direct hydrogel contact, indicating a comparably pronounced inflammatory activation. On the other hand, in HAEC the expression of tight junction proteins, as well as cytokine and matrix metalloproteinase secretion were not influenced by the hydrogels, suggesting a maintained endothelial cell function. This was in line with the finding that in HAEC increased thrombomodulin synthesis but no thrombomodulin membrane shedding occurred. First in vivo data obtained after subcutaneous implantation of the materials in immunocompetent mice revealed good integration of implants in the surrounding tissue, no progredient fibrous capsule formation, and no inflammatory tissue reaction in vivo. Overall, the study demonstrates the potential of gelatin-based hydrogels for temporal replacement and functional regeneration of damaged soft tissue. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effects of natural zeolite and ferric oxide to electromagnetic and reflection loss properties of polyurethane nanocomposite

NASA Astrophysics Data System (ADS)

Gultom, G.; Wirjosentono, B.; Ginting, M.; Sebayang, K.

2017-07-01

Microwave-absorptive polymeric composite materials are becoming important to protect interference of any communication systems due to increasing use of microwave-inducing devices. In this work, the microwave-absorptive polyurethane nanocomposites were prepared using natural zeolites of Sarulla North Sumatra and commercial ferric oxide as fillers. Weight ratios of the polyurethane to natural zeolite and ferric oxide were varied (90%:6%:4%; 80%:12%:8%; 70%:24%:6%) by weight. The fillers were prepared using ball milling technique and characterized for their particle size distributions using Particle Size Analyzer. The nanocomposites, prepared using in-situ reaction of polyethylene glycol, toluene diisocyanate and fillers. The complex permittivity (ε’and ε”) and complex permeability (μ’ and μ”) as electromagnetic properties were calculated using NRW method after collecting real and imaginary S parameter using Vector Network Analyzer measurement at X band frequency. Results show ratio of the fillers will affect the permeability, permittivity and reflection loss of the materials. The best reflection loss was shown -40.588 dB (>99 % absorption) at ratio for polyurethane : nanozeolite : ferric oxide (80%:12%:8%) by weight observed at 10.92 GHz. According to the measurement and calculation was shown the polyurethane filled with natural nanozeolite and ferric oxide is a good electromagnetic wave attenuation material.

Quantification of isocyanates and amines in polyurethane foams and coated products by liquid chromatography–tandem mass spectrometry

PubMed Central

Mutsuga, Motoh; Yamaguchi, Miku; Kawamura, Yoko

2014-01-01

An analytical method for the identification and quantification of 10 different isocyanates and 11 different amines in polyurethane (PUR) foam and PUR-coated products was developed and optimized. Isocyanates were extracted and derivatized with di-n-butylamine, while amines were extracted with methanol. Quantification was subsequently performed by liquid chromatography–tandem mass spectrometry. Using this methodology, residual levels of isocyanates and amines in commercial PUR products were quantified. Although the recoveries of certain isocyanates and amines were low, the main compounds used as monomers in the production of PUR products, and their decomposition species, were clearly identified at quantifiable levels. 2,4-and 2,6-toluenediisocyanate were detected in most PUR foam samples and a pastry bag in the range of 0.02–0.92 mg/kg, with their decomposition compounds, 2,4-and 2,6-toluenediamine, detected in all PUR foam samples in the range of 9.5–59 mg/kg. PUR-coated gloves are manufactured using 4,4′-methylenebisphenyl diisocyanate as the main raw material, and a large amount of this compound, in addition to 4,4′-methylenedianiline and dicyclohexylmethane-4,4′-diamine were found in these samples. PMID:24804074

Center for the Polyurethanes Industry summary of unpublished industrial hygiene studies related to the evaluation of emissions of spray polyurethane foam insulation.

PubMed

Wood, Richard D

2017-09-01

Spray polyurethane foam (SPF) insulation is used as thermal insulation for residential and commercial buildings. It has many advantages over other forms insulation; however, concerns have been raised related to chemical emissions during and after application. The American Chemistry Council's (ACC's) Center for the Polyurethanes Industry (CPI) has gathered previously unpublished industrial hygiene air sampling studies submitted by member companies that were completed during an eight-year period from 2007-2014. These studies address emissions from medium density closed cell and low density open cell formulations. This article summarizes the results of personal and area air samples collected during application and post application of SPF to interior building surfaces in both laboratory and field environments. Chemicals of interest included: Volatile Organic Compounds (VOCs), methylene diphenyl diisocyanate (MDI), flame retardants, amine catalysts, blowing agents, and aldehydes. Overall, the results indicate that SPF applicators and workers in close proximity to the application are potentially exposed to MDI in excess of recommended and governmental occupational exposure limits and should use personal protective equipment (PPE) consisting of air supplied respirators and full-body protective clothing to reduce exposure. Catalyst emissions can be reduced by using reactive catalysts in SPF formulations, and mechanical ventilation is important in controlling emissions during and after application.

Cell–material interactions on biphasic polyurethane matrix

PubMed Central

Dicesare, Patrick; Fox, Wade M.; Hill, Michael J.; Krishnan, G. Rajesh; Yang, Shuying; Sarkar, Debanjan

2013-01-01

Cell–matrix interaction is a key regulator for controlling stem cell fate in regenerative tissue engineering. These interactions are induced and controlled by the nanoscale features of extracellular matrix and are mimicked on synthetic matrices to control cell structure and functions. Recent studies have shown that nanostructured matrices can modulate stem cell behavior and exert specific role in tissue regeneration. In this study, we have demonstrated that nanostructured phase morphology of synthetic matrix can control adhesion, proliferation, organization and migration of human mesenchymal stem cells (MSCs). Nanostructured biodegradable polyurethanes (PU) with segmental composition exhibit biphasic morphology at nanoscale dimensions and can control cellular features of MSCs. Biodegradable PU with polyester soft segment and hard segment composed of aliphatic diisocyanates and dipeptide chain extender were designed to examine the effect polyurethane phase morphology. By altering the polyurethane composition, morphological architecture of PU was modulated and its effect was examined on MSC. Results show that MSCs can sense the nanoscale morphology of biphasic polyurethane matrix to exhibit distinct cellular features and, thus, signifies the relevance of matrix phase morphology. The role of nanostructured phases of a synthetic matrix in controlling cell–matrix interaction provides important insights for regulation of cell behavior on synthetic matrix and, therefore, is an important tool for engineering tissue regeneration. PMID:23255285

Novel route of synthesis for cellulose fiber-based hybrid polyurethane

NASA Astrophysics Data System (ADS)

Ikhwan, F. H.; Ilmiati, S.; Kurnia Adi, H.; Arumsari, R.; Chalid, M.

2017-07-01

Polyurethanes, obtained by the reaction of a diisocyanate compound with bifunctional or multifunctional reagent such as diols or polyols, have been studied intensively and well developed. The wide range modifier such as chemical structures and molecular weight to build polyurethanes led to designs of materials that may easily meet the functional product demand and to the extraordinary spreading of these materials in market. Properties of the obtained polymer are related to the chemical structure of polyurethane backbone. A number polyurethanes prepared from biomass-based monomers have been reported. Cellulose fiber, as a biomass material is containing abundant hydroxyl, promising material as chain extender for building hybrid polyurethanes. In previous researches, cellulose fiber was used as filler in synthesis of polyurethane composites. This paper reported a novel route of hybrid polyurethane synthesis, which a cellulose fiber was used as chain extender. The experiment performed by reacting 4,4’-Methylenebis (cyclohexyl isocyanate) (HMDI) and polyethylene glycol with variation of molecular weight to obtained pre-polyurethane, continued by adding micro fiber cellulose (MFC) with variation of type and composition in the mixture. The experiment was evaluated by NMR, FTIR, SEM and STA measurement. NMR and FTIR confirmed the reaction of the hybrid polyurethane. STA showed hybrid polyurethane has good thermal stability. SEM showed good distribution and dispersion of sorghum-based MFC.

Synthesis and Characterization of Hydrophilic-Hydrophobic Poly(Arylene Ether Sulfone) Random and Segmented Copolymers for Membrane Applications

NASA Astrophysics Data System (ADS)

Nebipasagil, Ali

Poly(arylene ether sulfone)s are high-performance engineering thermoplastics that have been investigated extensively over the past several decades due to their outstanding mechanical properties, high glass transition temperatures (Tg), solvent resistance and exceptional thermal, oxidative and hydrolytic stability. Their thermal and mechanical properties are highly suited to a variety of applications including membrane applications such as reverse osmosis, ultrafiltration, and gas separation. This dissertation covers structure-property-performance relationships of poly(arylene ether sulfone) and poly(ethylene oxide)-containing random and segmented copolymers for reverse osmosis and gas separation membranes. The second chapter of this dissertation describes synthesis of disulfonated poly(arylene ether sulfone) random copolymers with oligomeric molecular weights that contain hydrophilic and hydrophobic segments for thin film composite (TFC) reverse osmosis membranes. These copolymers were synthesized and chemically modified to obtain novel crosslinkable poly(arylene ether sulfone) oligomers with acrylamide groups on both ends. The acrylamideterminated oligomers were crosslinked with UV radiation in the presence of a multifunctional acrylate and a UV initiator. Transparent, dense films were obtained with high gel fractions. Mechanically robust TFC membranes were prepared from either aqueous or water-methanol solutions cast onto a commercial UDELRTM foam support. This was the first example that utilized a water or alcohol solvent system and UV radiation to obtain reverse osmosis TFC membranes. The membranes were characterized with regard to composition, surface properties, and water uptake. Water and salt transport properties were elucidated at the department of chemical engineering at the University of Texas at Austin. The gas separation membranes presented in chapter three were poly(arylene ether sulfone) and poly(ethylene oxide) (PEO)-containing polyurethanes. Poly(arylene ether sulfone) copolymers with controlled molecular weights were synthesized and chemically modified to obtain poly(arylene ether sulfone) polyols with aliphatic hydroxyethyl terminal functionality. The hydroxyethyl-terminated oligomers and a,u-hydroxy-terminated PEO were chain extended with a diisocyanate to obtain polyurethanes. Compositions with high poly(arylene ether sulfone) content relative to the hydrophilic PEO blocks were of interest due to their mechanical integrity. The membranes were characterized to analyze their compositions, thermal and mechanical properties, water uptake, and molecular weights. These membranes were also evaluated by collaborators at the University of Texas at Austin to explore single gas transport properties. The results showed that both polymer and transport properties closely related to PEO-content. The CO2/CH4 gas selectivity of our membranes were improved from 25 to 34 and the CO2/N2 gas selectivity nearly doubled from 25 to 46 by increasing PEO-content from 0 to 30 wt.% in polyurethanes. Chapter four also focuses on polymers for gas separation membranes. Disulfonated poly(arylene ether sulfone) and poly(ethylene oxide)-containing polyurethanes were synthesized for potential applications as gas separation membranes. Disulfonated polyols containing 20 and 40 mole percent of disulfonated repeat units with controlled molecular weights were synthesized. Poly(arylene ether sulfone) polyols and alpha,o-hydroxy-terminated poly(ethylene oxide) were subsequently chain extended with a diisocyanate to obtain polyurethanes. Thermal and mechanical characterization revealed that the polyurethanes had a phase-mixed complex morphology.

Enhancement of antibacterial properties of polyurethanes by chitosan and heparin immobilization

NASA Astrophysics Data System (ADS)

Kara, Filiz; Aksoy, E. Ayse; Yuksekdag, Zehranur; Aksoy, Serpil; Hasirci, Nesrin

2015-12-01

Being antibacterial is a required property for the materials used in medical devices and instruments. Polyurethanes (PUs) are one class of polymers widely used in the production of devices that especially come in contact with blood (e.g. heart valves, blood vessels, vascular grafts and catheters). In this study, hexamethylene diisocyanate based polyurethanes (PUh) were synthesized and antibacterial and anti-adhesive properties were added by immobilizing chitosan (CH) and heparin (Hep) on the samples of PUh via a stepwise process. Chemistry and topography of the modified film samples (PUh-CH and PUh-CH-Hep) were examined by Fourier Transform Infrared Spectrophotometry-Attenuated Total Reflectance (FTIR-ATR), Electron Spectroscopy for Chemical Analysis (ESCA) and Atomic Force Microscopy (AFM), and surface free energy (SFE) values after each step were determined by goniometer. PUh-CH and PUh-CH-Hep samples were found to be antibacterial against Staphylococcus aureus (S. aureus) and Staphylococcus epidermidis (S. epidermidis) (both Gram positive) and Escherichia coli (E. coli) and Pseudomonas aeruginosa (P. aeruginosa) (both Gram negative) bacteria, and bacterial adhesion results showed a significant decrease in the number of viable bacteria on both modified samples where PUh-CH-Hep was the most effective. The findings of this study show that polymeric surfaces can be effectively modified and converted to be antibacterial by chitosan and heparin immobilization, and presence of both chemicals enhance efficacy against bacteria.

Surface modification of bioactive glass nanoparticles and the mechanical and biological properties of poly(L-lactide) composites.

PubMed

Liu, Aixue; Hong, Zhongkui; Zhuang, Xiuli; Chen, Xuesi; Cui, Yang; Liu, Yi; Jing, Xiabin

2008-07-01

Novel bioactive glass (BG) nanoparticles/poly(L-lactide) (PLLA) composites were prepared as promising bone-repairing materials. The BG nanoparticles (Si:P:Ca=29:13:58 weight ratio) of about 40nm diameter were prepared via the sol-gel method. In order to improve the phase compatibility between the polymer and the inorganic phase, PLLA (M(n)=9700Da) was linked to the surface of the BG particles by diisocyanate. The grafting ratio of PLLA was in the vicinity of 20 wt.%. The grafting modification could improve the tensile strength, tensile modulus and impact energy of the composites by increasing the phase compatibility. When the filler loading reached around 4 wt.%, the tensile strength of the composite increased from 56.7 to 69.2MPa for the pure PLLA, and the impact strength energy increased from 15.8 to 18.0 kJ m(-2). The morphology of the tensile fracture surface of the composite showed surface-grafted bioactive glass particles (g-BG) to be dispersed homogeneously in the PLLA matrix. An in vitro bioactivity test showed that, compared to pure PLLA scaffold, the BG/PLLA nanocomposite demonstrated a greater capability to induce the formation of an apatite layer on the scaffold surface. The results of marrow stromal cell culture revealed that the composites containing either BG or g-BG particles have much better biocompatibility compared to pure PLLA material.

Exploiting β-Cyclodextrin in Molecular Imprinting for Achieving Recognition of Benzylparaben in Aqueous Media

PubMed Central

Asman, Saliza; Mohamad, Sharifah; Muhamad Sarih, Norazilawati

2015-01-01

The molecularly imprinted polymer (MIP) based on methacrylic acid functionalized β-cyclodextrin (MAA-β-CD) monomer was synthesized for the purpose of selective recognition of benzylparaben (BzP). The MAA-β-CD monomer was produced by bridging a methacrylic acid (MAA) and β-cyclodextrin (β-CD) using toluene-2,4-diisocyanate (TDI) by reacting the –OH group of MAA and one of the primary –OH groups of β-CD. This monomer comprised of triple interactions that included an inclusion complex, π–π interaction, and hydrogen bonding. To demonstrate β-CD performance in MIPs, two MIPs were prepared; molecularly imprinted polymer-methacrylic acid functionalized β-cyclodextrin, MIP(MAA-β-CD), and molecularly imprinted polymer-methacrylic acid, MIP(MAA); both prepared by a reversible addition fragmentation chain transfer polymerization (RAFT) in the bulk polymerization process. Both MIPs were characterized using the Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FESEM), and Brunauer-Emmett-Teller (BET). The presence of β-CD not only influenced the morphological structure, it also affected the specific surface area, average pore diameter, and total pore volume of the MIP. The rebinding of the imprinting effect was evaluated in binding experiments, which proved that the β-CD contributed significantly to the enhancement of the recognition affinity and selective adsorption of the MIP. PMID:25667978

Synthesis of graphene oxide grafted poly(lactic acid) with palladium nanoparticles and its application to serotonin sensing

NASA Astrophysics Data System (ADS)

Han, Hyoung Soon; You, Jung-Min; Jeong, Haesang; Jeon, Seungwon

2013-11-01

Graphene oxide (GO) has treated with methylene diphenyl diisocyanate (MDI) and subsequent 1,4-butanediol (BD) to create an anchoring OH site on the surface of GO (GO-MDI-OH). The OH groups of GO-MDI-OH were the initiators of the polymerization of poly(lactic acid) (PLA). The subsequent GO-g-PLA was synthesized by the polymerization reaction in the presence of GO-MDI-OH and PLA. The synthesized materials were characterized via 1H-NMR, Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), thermal analysis (differential scanning calorimeter (DSC), and thermogravimetric analysis (TGA)). The surface morphologies and degree of dispersions at G-g-PLA-metals were observed using a field emission scanning electron microscope (FE-SEM) and a transmission electron microscopy (TEM). The electrical conductivity of G-g-PLA-Pd was largely enhanced compared with those of GO and GO-g-PLA. G-g-PLA-Pd was used for the electrochemical detection of serotonin. Electrocatalytic activities were verified from the cyclic voltammetry (CV) and amperometric response in a 0.1 M phosphate buffer solution (PBS). A significantly higher concentration range (0.1-100.0 μM) and a lower detection limit (8.0 × 10-8 M, where s/n = 3) were found at the G-g-PLA-Pd modified glassy carbon electrode (GCE).

3D-Hydrogel Based Polymeric Nanoreactors for Silver Nano-Antimicrobial Composites Generation

PubMed Central

Soto-Quintero, Albanelly; Romo-Uribe, Ángel; Bermúdez-Morales, Víctor H.; Quijada-Garrido, Isabel

2017-01-01

This study underscores the development of Ag hydrogel nanocomposites, as smart substrates for antibacterial uses, via innovative in situ reactive and reduction pathways. To this end, two different synthetic strategies were used. Firstly thiol-acrylate (PSA) based hydrogels were attained via thiol-ene and radical polymerization of polyethylene glycol (PEG) and polycaprolactone (PCL). As a second approach, polyurethane (PU) based hydrogels were achieved by condensation polymerization from diisocyanates and PCL and PEG diols. In fact, these syntheses rendered active three-dimensional (3D) hydrogel matrices which were used as nanoreactors for in situ reduction of AgNO3 to silver nanoparticles. A redox chemistry of stannous catalyst in PU hydrogel yielded spherical AgNPs formation, even at 4 °C in the absence of external reductant; and an appropriate thiol-functionalized polymeric network promoted spherical AgNPs well dispersed through PSA hydrogel network, after heating up the swollen hydrogel at 103 °C in the presence of citrate-reductant. Optical and swelling behaviors of both series of hydrogel nanocomposites were investigated as key factors involved in their antimicrobial efficacy over time. Lastly, in vitro antibacterial activity of Ag loaded hydrogels exposed to Pseudomona aeruginosa and Escherichia coli strains indicated a noticeable sustained inhibitory effect, especially for Ag–PU hydrogel nanocomposites with bacterial inhibition growth capabilities up to 120 h cultivation. PMID:28763050

Measurements of airborne methylene diphenyl diisocyanate (MDI) concentration in the U.S. workplace.

PubMed

Booth, Karroll; Cummings, Barbara; Karoly, William J; Mullins, Sharon; Robert, William P; Spence, Mark; Lichtenberg, Fran W; Banta, J

2009-04-01

This article summarizes a large body of industry air sampling data (8134 samples) in which airborne MDI concentrations were measured in a wide variety of manufacturing processes that use either polymeric MDI (PMDI) or monomeric (pure) MDI. Data were collected during the period 1984 through 1999. A total of 606 surveys were conducted for 251 companies at 317 facilities. The database includes 3583 personal (breathing zone) samples and 4551 area samples. Data demonstrate that workplace airborne MDI concentrations are extremely low in a majority of the manufacturing operations. Most (74.6%) of the airborne MDI concentrations measured in the personal samples were nondetectable, i.e., below the limits of quantification (LOQs). A variety of validated industrial hygiene sampling/analytical methods were used for data collection; most are modifications of OSHA Method 47. The LOQs for these methods ranged from 0.1-0.5 microg/sample. The very low vapor pressures of both monomeric MDI and PMDI largely explain the low airborne concentrations found in most operations. However, processes or applications in which the chemical is sprayed or heated may result in higher airborne concentrations and higher exposure potentials if appropriate control measures are not implemented. Data presented in this article will be a useful reference for employers in helping them to manage their health and safety program as it relates to respiratory protection during MDI/PMDI applications.

Modeling shock-driven reaction in low density PMDI foam

NASA Astrophysics Data System (ADS)

Brundage, Aaron; Alexander, C. Scott; Reinhart, William; Peterson, David

Shock experiments on low density polyurethane foams reveal evidence of reaction at low impact pressures. However, these reaction thresholds are not evident over the low pressures reported for historical Hugoniot data of highly distended polyurethane at densities below 0.1 g/cc. To fill this gap, impact data given in a companion paper for polymethylene diisocyanate (PMDI) foam with a density of 0.087 g/cc were acquired for model validation. An equation of state (EOS) was developed to predict the shock response of these highly distended materials over the full range of impact conditions representing compaction of the inert material, low-pressure decomposition, and compression of the reaction products. A tabular SESAME EOS of the reaction products was generated using the JCZS database in the TIGER equilibrium code. In particular, the Arrhenius Burn EOS, a two-state model which transitions from an unreacted to a reacted state using single step Arrhenius kinetics, as implemented in the shock physics code CTH, was modified to include a statistical distribution of states. Hence, a single EOS is presented that predicts the onset to reaction due to shock loading in PMDI-based polyurethane foams. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's NNSA under Contract DE-AC04-94AL85000.

Potentiometric chemical sensors from lignin-poly(propylene oxide) copolymers doped by carbon nanotubes.

PubMed

Rudnitskaya, Alisa; Evtuguin, Dmitry V; Costa, Luis C; Graça, M Pedro F; Fernandes, António J S; Correia, M Rosario P; Gomes, M Teresa S R; Oliveira, J A B P

2013-01-21

Hardwood and softwood lignins obtained from industrial sulphite and kraft and laboratory oxygen-organosolv pulping processes were employed in co-polymerization with tolylene 2,4-diisocyanate terminated poly(propylene glycol). The obtained lignin-based polyurethanes were doped with 0.72 w/w% of multiwall carbon nanotubes (MWCNTs) with the aim of increasing their electrical conductivity to the levels suitable for sensor applications. Effects of the polymer doping with MWCNTs were assessed using electrical impedance (EIS) and UV-Resonance Raman (UV-RR) spectroscopy. Potentiometric sensors were prepared by drop casting of liquid polymer on the surface of carbon glass or platinum electrodes. Lignin-based sensors displayed a very low or no sensitivity to all alkali, alkali-earth and transition metal cations ions except Cr(VI) at pH 2. Response to Cr(VI) values of 39, 50 and 53 mV pX(-1) for the sensors based on kraft, organosolv and lignosulphonate lignins, respectively, were observed. Redox sensitivity values close to the theoretical values of 20 and 21 mV pX(-1) for organosolv and lignosulphonate based sensors respectively were detected in the Cr(III)/Cr(VI) solutions while a very low response was observed in the solutions containing Fe(CN)(6)(3-/4-). Conducting composite lignin-based polyurethanes doped with MWCNTs were suggested as being promising materials for Cr(VI)-sensitive potentiometric sensors.

Patch-test reactions to plastic and glue allergens.

PubMed

Kanerva, L; Jolanki, R; Alanko, K; Estlander, T

1999-07-01

Plastics and glues are common causes of occupational dermatoses, but only few reports have dealt with patch-test reactions caused by plastic and glue allergens. Patients exposed to plastics and remitted to an occupational dermatology clinic, were patch-tested with 50-53 plastic and glue allergens during a 6-year period. Conventional patch-test techniques were used. The most common causes of allergic patch-test reactions in 360 patients were novolac epoxy resin (5.1%), phenol formaldehyde resin (3.1%), 4-tert-butylcatechol (2.6%), phenyl glycidyl ether (2.6%), diaminodiphenyl methane (2.2%), benzoyl peroxide (2.2%), hexamethylene tetramine (2.0%) and o-cresyl glycidyl ether (1.6%). The allergens that most often elicited irritant patch-test reactions were: benzoyl peroxide (9.5%), abitol alcohol (3.6%), hydroquinone (3.1%), acid-catalyzed phenol formaldehyde resin (2.5%) and toluene diisocyanate (1.9%). Twenty-six out of 53 chemicals caused no allergic reaction during the 6-year period. Plastic allergens in the standard series provoked allergic reactions with formaldehyde (5.8%), diglycidyl ether of bisphenol A (3.2%), 4-tert-butylphenol-formaldehyde-resin (1.1%), toluene sulphonamide formaldehyde-resin (1.1%) and triethylenglycol diacrylate (0.4%). Although half of the plastic chemicals gave no allergic patch-test reactions during a 6-year period, with unusual allergens this low yield needs to be accepted, because otherwise rare allergies will not be detected. Also a negative reaction has diagnostic value.

Microencapsulation of 2-octylcyanoacrylate tissue adhesive for self-healing acrylic bone cement.

PubMed

Brochu, Alice B W; Chyan, William J; Reichert, William M

2012-10-01

Here, we report the first phase of developing self-healing acrylic bone cement: the preparation and characterization of polyurethane (PUR) microcapsules containing a medical cyanoacrylate tissue adhesive. Capsules were prepared by interfacial polymerization of a toluene-2,4-diisocyanate-based polyurethane prepolymer with 1,4-butanediol to encapsulate 2-octylcyanoacrylate (OCA). Various capsule characteristics, including: resultant morphology, average size and size distribution, shell thickness, content and reactivity of encapsulated agent, and shelf life are investigated and their reliance on solvent type and amount, surfactant type and amount, temperature, pH, agitation rate, reaction time, and mode of addition of the oil phase to the aqueous phase are presented. Capsules had average diameters ranging from 74 to 222 μm and average shell thicknesses ranging from 1.5 to 6 μm. The capsule content was determined via thermogravimetric analysis and subsequent analysis of the capsules following up to 8 weeks storage revealed minimal loss of core contents. Mechanical testing of OCA-containing capsules showed individual capsules withstood compressive forces up to a few tenths of Newtons, and the contents released from crushed capsules generated tensile adhesive forces of a few Newtons. Capsules were successfully mixed into the poly(methyl methacrylate) bone cement, surviving the mixing process, exposure to methyl methacrylate monomer, and the resulting exothermic matrix curing. Copyright © 2012 Wiley Periodicals, Inc.

Isocyanate exposure assessment combining industrial hygiene methods with biomonitoring for end users of orthopedic casting products.

PubMed

Pearson, Ronald L; Logan, Perry W; Kore, Anita M; Strom, Constance M; Brosseau, Lisa M; Kingston, Richard L

2013-07-01

Previous studies have suggested a potential risk to healthcare workers applying isocyanate-containing casts, but the authors reached their conclusions based on immunological or clinical pulmonology test results alone. We designed a study to assess potential exposure to methylene diphenyl diisocyanate (MDI) among medical personnel applying orthopedic casts using two different application methods. Air, dermal, surface, and glove permeation sampling methods were combined with urinary biomonitoring to assess the overall risk of occupational asthma to workers handling these materials. No MDI was detected in any of the personal and area air samples obtained. No glove permeation of MDI was detected. A small proportion of surface (3/45) and dermal wipe (1/60) samples were positive for MDI, but were all from inexperienced technicians. Urinary metabolites of MDI [methylenedianiline (MDA)] were detected in three of six study participants prior to both a 'dry' and 'wet' application method, five of six after the dry method, and three of six after the wet method. All MDA results were below levels noted in worker or general populations. Our conclusion is that the risk of MDI exposure is small, but unquantifiable. Because there is some potential risk of dermal exposure, medical personnel are instructed to wear a minimum of 5-mil-thick (5 mil = 0.005 inches) nitrile gloves and avoid contact to unprotected skin. This could include gauntlets, long sleeves, and/or a laboratory coat.

Castor Oil Based Polyurethanes: Synthesis and Characterization

NASA Astrophysics Data System (ADS)

Macalino, AD; Salen, VA; Reyes, LQ

2017-09-01

In this study, polyurethanes based on castor oil and 1,6-hexamethylene diisocyanate (HMDI) were synthesized with varying weight ratio of the castor oil and HMDI. The formation of urethane linkages was verified through the use of a fourier transform infrared spectroscopy (FTIR). The hydrophilicity of the films was evaluated through the use of a contact angle meter and it was found that the contact angle of all the films were below 90 degrees which confirms their hydrophilicity. The thermal stability of the PU films were studies through the use of a thermal gravimetric analyzer and found that all of the polyurethane films exhibited two weight loss events at elevated temperatures wherein the first weight loss event was observed to occur at 285°C to 384°C while the second weight loss event was observed at around 521°C to 551°C. The hardness, elastic modulus, and tensile elongation of the PU films were determined by using a universal testing machine (UTM) where it was found out that the hardness and the elastic modulus of the film is directly proportional with HMDI loading while the tensile elongation is inversely proportional to it. Lastly, it was known through the swelling studies of the PU films that it does not swell, this is due to the presence of unreacted triglycerides in the material, which prevents water from permeating to the films.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alviso, C; Harvey, C; Vance, A

Removable epoxy foam (REF) is a novel material developed by researchers at Sandia National Laboratories to simplify the removal of encapsulants from electronic components [McElhanon, et al., Journal of Applied Polymer Science, 2002, 85, 1496-1502]. The material is based on a resin that includes a thermally reversible chemical bond. When the material is heated at relatively mild temperatures ({approx}50-90 C) in the presence of appropriate solvents, the reversible bonds are broken, and the material is easily rinsed away. In order to ease the removal of the encapsulant for surveillance purposes, it was proposed to use REF in the W80 LEPmore » in place of the polyurethane TDI (toluene diisocyanate), which is being phased out at the Kansas City Plant due to toxicity concerns. Colleagues at Sandia noted that REF exhibited especially high outgassing of the liquid fluorinert, FC-72, which is used at a level of 5 wt% as the blowing agent in the foaming process. After obtaining a sample of the material from Sandia, headspace solid phase microextraction gas chromatography-mass spectrometry (SPME GC/MS) measurements were performed. These measurements revealed significant outgassing of fluorinert as well as other solvents and siloxanes [Memo, Vance, 3/3/05 & Vance, Foam PRT presentation UCRL-PRES-212462]. This report is intended to summarize foam outgassing studies performed at LLNL in support of the W80 LEP.« less

Biocompatible, Biodegradable, and Electroactive Polyurethane-Urea Elastomers with Tunable Hydrophilicity for Skeletal Muscle Tissue Engineering.

PubMed

Chen, Jing; Dong, Ruonan; Ge, Juan; Guo, Baolin; Ma, Peter X

2015-12-30

It remains a challenge to develop electroactive and elastic biomaterials to mimic the elasticity of soft tissue and to regulate the cell behavior during tissue regeneration. We designed and synthesized a series of novel electroactive and biodegradable polyurethane-urea (PUU) copolymers with elastomeric property by combining the properties of polyurethanes and conducting polymers. The electroactive PUU copolymers were synthesized from amine capped aniline trimer (ACAT), dimethylol propionic acid (DMPA), polylactide, and hexamethylene diisocyanate. The electroactivity of the PUU copolymers were studied by UV-vis spectroscopy and cyclic voltammetry. Elasticity and Young's modulus were tailored by the polylactide segment length and ACAT content. Hydrophilicity of the copolymer films was tuned by changing DMPA content and doping of the copolymer. Cytotoxicity of the PUU copolymers was evaluated by mouse C2C12 myoblast cells. The myogenic differentiation of C2C12 myoblasts on copolymer films was also studied by analyzing the morphology of myotubes and relative gene expression during myogenic differentiation. The chemical structure, thermal properties, surface morphology, and processability of the PUU copolymers were characterized by NMR, FT-IR, gel permeation chromatography (GPC), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and solubility testing, respectively. Those biodegradable electroactive elastic PUU copolymers are promising materials for repair of soft tissues such as skeletal muscle, cardiac muscle, and nerve.

Alternating block polyurethanes based on PCL and PEG as potential nerve regeneration materials.

PubMed

Li, Guangyao; Li, Dandan; Niu, Yuqing; He, Tao; Chen, Kevin C; Xu, Kaitian

2014-03-01

Polyurethanes with regular and controlled block arrangement, i.e., alternating block polyurethanes (abbreviated as PUCL-alt-PEG) based on poly(ε-caprolactone) (PCL-diol) and poly(ethylene glycol) (PEG) was prepared via selectively coupling reaction between PCL-diol and diisocyanate end-capped PEG. Chemical structure, molecular weight, distribution, and thermal properties were systematically characterized by FTIR, (1)H NMR, GPC, DSC, and TGA. Hydrophilicity was studied by static contact angle of H2O and CH2I2. Film surface was observed by scanning electron microscope (SEM) and atomic force microscopy, and mechanical properties were assessed by universal test machine. Results show that alternating block polyurethanes give higher crystal degree, higher mechanical properties, and more hydrophilic and rougher (deep ravine) surface than their random counterpart, due to regular and controlled structure. Platelet adhesion illustrated that PUCL-alt-PEG has better hemocompatibility and the hemacompatibility was affected significantly by PEG content. Excellent hemocompatibility was obtained with high PEG content. CCK-8 assay and SEM observation revealed much better cell compatibility of fibroblast L929 and rat glial cells on the alternating block polyurethanes than that on random counterpart. Alternating block polyurethane PUC20-a-E4 with optimized composition, mechanical, surface properties, hemacompatibility, and highest cell growth and proliferation was achieved for potential use in nerve regeneration. Copyright © 2013 Wiley Periodicals, Inc.

Degradability in vitro of polyurethanes based on synthetic atactic poly[(R,S)-3-hydroxybutyrate].

PubMed

Brzeska, J; Janeczek, H; Janik, H; Kowalczuk, M; Rutkowska, M

2015-01-01

The aim of the present study was to determine the degradability of aliphatic polyurethanes, based on a different amount of synthetic, atactic poly[(R,S)-3-hydroxybutyrate] (a-PHB), in hydrolytic (phosphate buffer) and oxidative (H2O2/CoCl2) solutions. The soft segments were built with atactic poly[(R,S)-3-hydroxybutyrate] and polycaprolactone or polyoxytetramethylenediols, whereas hard segments were the reaction product of 4,4'-methylenedicyclohexyl diisocyanate and 1,4-butanediol.The selected properties - density and morphology of polymer surfaces - which could influence the sensitivity of polymers to degradation processes - were analyzed.The analysis of molecular mass (GPC), thermal properties (DSC) and the sample weight changes were undertaken to estimate the degree of degradability of polymer samples after incubation in environments studied.Investigated polyurethanes were amorphous with the very low amount of crystalline phases of hard segments.The polyurethane synthesized with a poly[(R,S)-3-hydroxybutyrate] and polyoxytetramethylenediol at a molar ratio of NCO:OH=3.7:1 (prepolymer step) appeared as the most sensitive for both degradative solutions. Its weight and molecular mass losses were the highest in comparison to other investigated polyurethanes.It could be expected that playing with the amount of poly[(R,S)-3-hydroxybutyrate] in polyurethane synthesis the rate of polyurethane degradation after immersion in living body would be modeled.

Manufacturing and process optimization of porous rice straw board

NASA Astrophysics Data System (ADS)

Liu, Dejun; Dong, Bing; Bai, Xuewei; Gao, Wei; Gong, Yuanjuan

2018-03-01

Development and utilization of straw resources and the production of straw board can dramatically reduce straw waste and environmental pollution associated with straw burning in China. However, the straw board production faces several challenges, such as improving the physical and mechanical properties, as well as eliminating its formaldehyde content. The recent research was to develop a new straw board compound adhesive containing both inorganic (MgSO4, MgCO3, active silicon and ALSiO4) and organic (bean gum and modified Methyl DiphenylDiisocyanate, MDI) gelling materials, to devise a new high frequency straw board hot pressing technique and to optimize the straw board production parameters. The results indicated that the key hot pressing parameters leading to porous straw board with optimal physical and mechanical properties. These parameters are as follows: an adhesive containing a 4:1 ratio of inorganic-to-organic gelled material, the percentage of adhesive in the total mass of preload straw materials is 40%, a hot-pressing temperature in the range of 120 °C to 140 °C, and a high frequency hot pressing for 10 times at a pressure of 30 MPa. Finally, the present work demonstrated that porous straw board fabricated under optimal manufacturing condition is an environmentally friendly and renewable materials, thereby meeting national standard of medium density fiberboard (MDF) with potential applications in the building industry.

Smart hydrogel-functionalized textile system with moisture management property for skin application

NASA Astrophysics Data System (ADS)

Wang, Xiaowen; Hu, Huawen; Yang, Zongyue; He, Liang; Kong, Yeeyee; Fei, Bin; Xin, John H.

2014-12-01

In this study, a functional textile-based material for topical skin application was fabricated by coating a thermoresponsive hydrogel onto one side of absorbent nonwoven fabric. The thermoresponsive hydrogel was synthesized easily through coupling of poly (ethylene glycol) (PEG) and poly (ɛ-caprolactone) (PCL) with hexamethylene diisocyanate (HMDI) as a chemical linker. The chemical structure of the as-prepared triblock copolymer hydrogel was unraveled by FTIR and 1H NMR analysis. The hydrogel showed a temperature-triggered sol-gel transition behavior and high potential for use as drug controlled release. When the surrounding temperature was close to the skin temperature of around 34 °C, it became a moisture management system where the liquids including sweat, blood, and other body fluids can be transported unidirectionally from one fabric side with the hydrophobic hydrogel coating to the untreated opposite side. This thereby showed that the thermoresponsive hydrogel-coated textile materials had a function to keep topical skin area clean, breathable, and comfortable, thus suggesting a great potential and significance for long-term skin treatment application. The structure and surface morphology of the thermoresponsive hydrogel, in vitro drug release behavior, and the mechanism of unidirectional water transport were investigated in detail. Our success in preparation of the functional textile composites will pave the way for development of various polymer- or textile-based functional materials that are applicable in the real world.

Electrospinning of gelatin with tunable fiber morphology from round to flat/ribbon.

PubMed

Topuz, Fuat; Uyar, Tamer

2017-11-01

The electrospinning of gelatin with tunable fiber morphology from round to flat/ribbon was shown, and the detailed studies were conducted to correlate the fiber morphology with electrospinning process parameters and gelatin concentration in electrospinning solution. Particularly, variations in the applied voltage and the concentration of gelatin led to the transition of fiber shape from round to flat/ribbon. The formation of flat-shaped fibers was attributed to rapid evaporation of the solvent (formic acid) from the fiber matrix with increasing the applied voltage and gelatin concentration. On the other hand, round fibers were due to the steady evaporation of formic acid throughout the cross-section of fibers. WAXS analysis revealed that the loss of triple-helical crystalline structure in gelatin after the electrospinning process. The gelatin fibers were cross-linked through treatment with toluene 2,4-diisocyanate (TDI) in a mixed solution of acetone and pyridine, and XPS confirmed the cross-linking of the fibers over an increased carbon content on the elemental composition of the fiber surface due to the incorporated TDI moieties. Overall, this study focuses on morphological tuning of gelatin electrospun fibers towards a flat/ribbon-like structure by variation of electrospinning parameters and polymer concentration, and thus, the proposed concept can be adapted towards flattened/ribbon-like fibers of other protein-based systems by electrospinning. Copyright © 2017 Elsevier B.V. All rights reserved.

Layer-by-layer assembly of type I collagen and chondroitin sulfate on aminolyzed PU for potential cartilage tissue engineering application

NASA Astrophysics Data System (ADS)

He, Xianyun; Wang, Yingjun; Wu, Gang

2012-10-01

In this paper, a two-step method was used to synthesize a biodegradable polyurethane (PU) composed of L-lysine ethyl ester diisocyanate (LDI), poly(ɛ-caprolactone) diols (PCL-diol) and 1,4:3,6-dianhydro-D-sorbitol (isosorbide). Amino groups were introduced onto the surface of the PU membrane by an amination reacting with 1,3-propanediamine to produce polycationic substratum. And then, type I collagen (Col) and chondroitin sulfate (CS) were deposited alternately on the polycationic substratum through layer-by-layer (LBL) assembly technology. The FTIR and 1H NMR results showed that the polyurethane was successfully synthesized. Rhodamine B isothiocyanate (RBITC) fluorescence spectrum indicated that amino groups were successfully introduced onto the PU surface. The results of quartz-crystal microbalance (QCM) and RBITC-Col fluorescence spectroscopy monitoring the LBL assemble process presented that the Col/CS deposited alternately on the PU surface. X-ray photoelectron spectroscopy (XPS) results displayed that the CS deposited on the PU surface as well. The surface of the assembled PU became even smoother observed from the surface morphology by atomic force microscopy (AFM) imaging. The hydrophilicity of the PU membrane was greatly enhanced though the modification of LBL assembly. The PU modified with the adsorption of Col/CS may be a potential application for cartilage tissue engineering due to its created mimicking chondrogenic environment.

Cytocompatibility and Mechanical Properties of Short Phosphate Glass Fibre Reinforced Polylactic Acid (PLA) Composites: Effect of Coupling Agent Mediated Interface

PubMed Central

Hasan, Muhammad Sami; Ahmed, Ifty; Parsons, Andrew; Walker, Gavin; Scotchford, Colin

2012-01-01

In this study three chemical agents Amino-propyl-triethoxy-silane (APS), sorbitol ended PLA oligomer (SPLA) and Hexamethylene diisocyanate (HDI) were identified to be used as coupling agents to react with the phosphate glass fibre (PGF) reinforcement and the polylactic acid (PLA) polymer matrix of the composite. Composites were prepared with short chopped strand fibres (l = 20 mm, ϕ = 20 µm) in a random arrangement within PLA matrix. Improved, initial composite flexural strength (~20 MPa) was observed for APS treated fibres, which was suggested to be due to enhanced bonding between the fibres and polymer matrix. Both APS and HDI treated fibres were suggested to be covalently linked with the PLA matrix. The hydrophobicity induced by these coupling agents (HDI, APS) helped to resist hydrolysis of the interface and thus retained their mechanical properties for an extended period of time as compared to non-treated control. Approximately 70% of initial strength and 65% of initial modulus was retained by HDI treated fibre composites in contrast to the control, where only ~50% of strength and modulus was retained after 28 days of immersion in PBS at 37 °C. All coupling agent treated and control composites demonstrated good cytocompatibility which was comparable to the tissue culture polystyrene (TCP) control, supporting the use of these materials as coupling agent’s within medical implant devices. PMID:24955744

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fabbri, L.M.; Danieli, D.; Crescioli, S.

We report the case of a 43-yr-old car painter who died within 1 h of exposure to a polyurethane paint in the workplace. A diagnosis of asthma induced by toluene diisocyanate (TDI) had been established 6 yr before, when he underwent inhalation challenges with carbachol and with TDI. The subject had airway hyperresponsiveness to carbachol (PD20FEV1 carbachol = 0.32 mg; normal value greater than 1.0 mg) and developed an early and long-lasting asthmatic reaction after exposure to TDI in the laboratory. Although it was recommended that he change his job or stop using paints containing isocyanates, he continued to workmore » as a car painter, taking antiasthmatic drugs both at work and at home to control asthma symptoms. On Monday, October 6, 1986, at 11:30 A. M., he developed a severe attack of asthma while he was mixing the 2 components of a polyurethane paint. Taken to hospital, he was dead on arrival. Autopsy showed no evidence of cardiac or brain disease; lungs were overinflated, the cut surface showed grey glistening mucous plugs in in the airways. Histologic examination showed denudation of airway epithelium and thickening of the basement membrane with infiltration of the lamina propria by polymorphonuclear leukocytes, mainly eosinophils, and diffuse mucous plugging of bronchioles. Bronchial smooth muscle appeared hyperplastic and disarrayed, and lung parenchyma showed focal areas of alveolar destruction adjacent to areas of perfectly intact alveolar walls.« less

Linear and crosslinked Polyurethanes based catalysts for reduction of methylene blue.

PubMed

Sultan, Misbah; Javeed, Asma; Uroos, Maliha; Imran, Muhammad; Jubeen, Farhat; Nouren, Shazia; Saleem, Nazish; Bibi, Ismat; Masood, Rashid; Ahmed, Waqas

2018-02-15

The large amount of synthetic dyes in effluents is a serious concern to be addressed. The chemical reduction is one of the potential way to resolve this problem. In this study, linear and crosslinked polyurethanes i.e. LPUR & CLPUR were synthesized from toluene diisocyanate (TDI), polyethylene glycol (PEG;1000g/mole) and tetraethylenepentamine (TEPA). The structure and morphology of synthesized materials were examined by FTIR, SEM and BET. The CLPUR was found stable in aqueous system with 0.80g/cm 3 density and 16.4998m 2 g -1 surface area. These materials were applied for the reduction of methylene blue in presence of NaBH 4 . Both, polymers catalyzed the process and showed 100% reduction in 16 and 28mins., respectively, while, the reduction rate was significantly low in absence of these materials, even after 120mins. Furthermore, negligible adsorption was observed with only 7% removal of dye. The best reduction rates were observed at low concentration of dye, increasing concentration of NaBH 4 and with more dosage of polymeric catalyst. The kinetic study of process followed zero order kinetics. It was hence concluded that both synthesized polymers played a catalytic role in reduction process. However, stability in aqueous system and better efficiency in reduction process endorsed CLPUR as an optimal choice for further studies. Copyright © 2017 Elsevier B.V. All rights reserved.

The effect of functional forms of nitrogen on fuel-NOx emissions.

PubMed

Zhang, Linghui; Su, Dagen; Zhong, Mingfeng

2015-01-01

This work explores the effects of different nitrogen functional forms on fuel-NOx emissions at 900 °C. The majority of tests are performed with an excess air coefficient of 1.4. Fuel-NOx is detected by measuring N-(1-naphthyl) ethylenediamine dihydrochloride (C₁₂H₁₆Cl₂N₂) via spectrophotometry. The different functional forms of nitrogen in the raw materials are identified by using X-ray photoelectron spectroscopy (XPS). A reliable density functional theory (DFT) method at the B3LYP/6-311++G** level is employed to investigate the reaction pathways of all functional forms of nitrogen during combustion. The results indicate that the functional forms of nitrogen influence the formation of nitrogen oxides. While under the same experimental conditions, fuel-NOx emissions increase by using less activation energy and nitrogen-containing groups with poor thermal stability. It is determined that fuel-NOx emissions vary in the following order: glycine > pyrrole > pyridine > methylenedi-p-phenylene diisocyanate (MDI). Glycine is the chain structure of amino acids in waste-leather and has low activation energy and poor thermal stability. With these properties, it is noted that glycine produces the most fuel-NOx in all of the raw materials studied. More pyrrole than pyridine in coal lead to high yields of fuel-NOx. The lowest yields of fuel-NO x are obtained using polyurethanes in waste-PU.

Development of Photocrosslinkable Urethane-Doped Polyester Elastomers for Soft Tissue Engineering

PubMed Central

Zhang, Yi; Tran, Richard T.; Gyawali, Dipendra; Yang, Jian

2012-01-01

Finding an ideal biomaterial with the proper mechanical properties and biocompatibility has been of intense focus in the field of soft tissue engineering. This paper reports on the synthesis and characterization of a novel crosslinked urethane-doped polyester elastomer (CUPOMC), which was synthesized by reacting a previously developed photocrosslinkable poly (octamethylene maleate citrate) (POMC) prepolymers (pre-POMC) with 1,6-hexamethylene diisocyanate (HDI) followed by thermo- or photo-crosslinking polymerization. The mechanical properties of the CUPOMCs can be tuned by controlling the molar ratios of pre-POMC monomers, and the ratio between the prepolymer and HDI. CUPOMCs can be crosslinked into a 3D network through polycondensation or free radical polymerization reactions. The tensile strength and elongation at break of CUPOMC synthesized under the known conditions range from 0.73±0.12MPa to 10.91±0.64MPa and from 72.91±9.09% to 300.41±21.99% respectively. Preliminary biocompatibility tests demonstrated that CUPOMCs support cell adhesion and proliferation. Unlike the pre-polymers of other crosslinked elastomers, CUPOMC pre-polymers possess great processability demonstrated by scaffold fabrication via a thermally induced phase separation method. The dual crosslinking methods for CUPOMC pre-polymers should enhance the versatile processability of the CUPOMC used in various conditions. Development of CUPOMC should expand the choices of available biodegradable elastomers for various biomedical applications such as soft tissue engineering. PMID:23565318

Polyols from Microwave Liquefied Bagasse and Its Application to Rigid Polyurethane Foam.

PubMed

Xie, Jiulong; Zhai, Xianglin; Hse, Chung Yun; Shupe, Todd F; Pan, Hui

2015-12-08

Bagasse flour (BF) was liquefied using bi-component polyhydric alcohol (PA) as a solvent and phosphoric acid as a catalyst in a microwave reactor. The effect of BF to solvent ratio and reaction temperatures on the liquefaction extent and characteristics of liquefied products were evaluated. The results revealed that almost 75% of the raw bagasse was converted into liquid products within 9 min at 150 °C with a BF to solvent ratio of 1/4. The hydroxyl and acid values of the liquefied bagasse (LB) varied with the liquefied conditions. High reaction temperature combining with low BF to solvent ratio resulted in a low hydroxyl number for the LB. The molecular weight and polydispersity of the LB from reactions of 150 °C was lower compared to that from 125 °C. Rigid polyurethane (PU) foams were prepared from LB and methylene diphenyl diisocyanate (MDI), and the structural, mechanical and thermal properties of the PU foam were evaluated. The PU foams prepared using the LB from high reaction temperature showed better physical and mechanical performance in comparison to those from low reaction temperature. The amount of PA in the LB has the ability of increasing thermal stability of LB-PU foams. The results in this study may provide fundamental information on integrated utilizations of sugarcane bagasse via microwave liquefaction process.

Polyols from Microwave Liquefied Bagasse and Its Application to Rigid Polyurethane Foam

PubMed Central

Xie, Jiulong; Zhai, Xianglin; Hse, Chung Yun; Shupe, Todd F.; Pan, Hui

2015-01-01

Bagasse flour (BF) was liquefied using bi-component polyhydric alcohol (PA) as a solvent and phosphoric acid as a catalyst in a microwave reactor. The effect of BF to solvent ratio and reaction temperatures on the liquefaction extent and characteristics of liquefied products were evaluated. The results revealed that almost 75% of the raw bagasse was converted into liquid products within 9 min at 150 °C with a BF to solvent ratio of 1/4. The hydroxyl and acid values of the liquefied bagasse (LB) varied with the liquefied conditions. High reaction temperature combining with low BF to solvent ratio resulted in a low hydroxyl number for the LB. The molecular weight and polydispersity of the LB from reactions of 150 °C was lower compared to that from 125 °C. Rigid polyurethane (PU) foams were prepared from LB and methylene diphenyl diisocyanate (MDI), and the structural, mechanical and thermal properties of the PU foam were evaluated. The PU foams prepared using the LB from high reaction temperature showed better physical and mechanical performance in comparison to those from low reaction temperature. The amount of PA in the LB has the ability of increasing thermal stability of LB-PU foams. The results in this study may provide fundamental information on integrated utilizations of sugarcane bagasse via microwave liquefaction process. PMID:28793725

Toxicity Ranking and Toxic Mode of Action Evaluation of Commonly Used Agricultural Adjuvants on the Basis of Bacterial Gene Expression Profiles

PubMed Central

Nobels, Ingrid; Spanoghe, Pieter; Haesaert, Geert; Robbens, Johan; Blust, Ronny

2011-01-01

The omnipresent group of pesticide adjuvants are often referred to as “inert” ingredients, a rather misleading term since consumers associate this term with “safe”. The upcoming new EU regulation concerning the introduction of plant protection products on the market (EC1107/2009) includes for the first time the demand for information on the possible negative effects of not only the active ingredients but also the used adjuvants. This new regulation requires basic toxicological information that allows decisions on the use/ban or preference of use of available adjuvants. In this study we obtained toxicological relevant information through a multiple endpoint reporter assay for a broad selection of commonly used adjuvants including several solvents (e.g. isophorone) and non-ionic surfactants (e.g. ethoxylated alcohols). The used assay allows the toxicity screening in a mechanistic way, with direct measurement of specific toxicological responses (e.g. oxidative stress, DNA damage, membrane damage and general cell lesions). The results show that the selected solvents are less toxic than the surfactants, suggesting that solvents may have a preference of use, but further research on more compounds is needed to confirm this observation. The gene expression profiles of the selected surfactants reveal that a phenol (ethoxylated tristyrylphenol) and an organosilicone surfactant (ethoxylated trisiloxane) show little or no inductions at EC20 concentrations, making them preferred surfactants for use in different applications. The organosilicone surfactant shows little or no toxicity and good adjuvant properties. However, this study also illustrates possible genotoxicity (induction of the bacterial SOS response) for several surfactants (POEA, AE, tri-EO, EO FA and EO NP) and one solvent (gamma-butyrolactone). Although the number of compounds that were evaluated is rather limited (13), the results show that the used reporter assay is a promising tool to rank commonly used agricultural adjuvants based on toxicity and toxic mode of action data. PMID:22125591

Conducting polymer actuator based on chemically deposited polypyrrole and polyurethane-based solid polymer electrolyte working in air

NASA Astrophysics Data System (ADS)

Choi, Hwa-Jeong; Song, Young-Min; Chung, Ildoo; Ryu, Kwang-Sun; Jo, Nam-Ju

2009-02-01

Conducting polymers (CPs), such as polypyrrole, polythiophene, and polyaniline, are unique in that they have switchable properties due to their two or more mechanically stable oxidation states. Thus, their films or coatings can be easily switched by the application of a small voltage and current to change their volume during electrochemical redox processes. In particular, polypyrrole (PPy) has been studied most extensively because of its high electrical conductivity and good environmental stability under ambient conditions. In this work, we have studied a new CP actuator, fully polymeric, assembled with two PPy film electrodes and a solid polymer electrolyte (SPE), polyurethane/Mg(ClO4)2. Polyurethanes (PUs) were synthesized from 4,4'-diphenylmethane diisocyanate (MDI), 1,4-butanediol (1,4-BD) and three types of polyol: poly(ethylene glycol) (PEG), poly(propylene glycol) (PPG), and PPG-block-PEG-block-PPG (PPG-co-PEG). The chemical polymerization of PPy by immersion in Py monomer aqueous solution and oxidant aqueous solution is an adequate method to prepare PU/PPy composite film as an actuator. To find the proper thickness of the PPy coating layer for actuation, we measured the displacements of the actuators according to the thickness of the PPy coating layer. The displacement of all actuators is discussed in connection with the properties of the SPE and PPy. All the results obtained in this work show the feasibility of electrochemomechanical devices based on PPy and SPE film being able to work in air.

Improving the elasticity and cytophilicity of biodegradable polyurethane by changing chain extender.

PubMed

Zhang, Changhong; Zhang, Ning; Wen, Xuejun

2006-11-01

Two types of biodegradable polyurethanes (PUs) were synthesized from methylene di-p-phenyl-diisocyanate (MDI), polycaprolactone diol (PCL-diol), and chain extenders of either butanediol (BD) or 2,2'-(methylimino)diethanol (MIDE). The effects of two types of chain extenders on the degradation, mechanical properties, hydrophilicity, and cytophilicity of PUs were evaluated. In vitro degradation studies showed that PU containing MIDE has a higher degradation rate than PU synthesized using BD as a chain extender. Mechanical testing on dry and wet samples demonstrated that PU containing MIDE has a much higher elongation in the elastic region than PU containing BD. PU containing MIDE is more hydrophilic and retains more liquid during in vitro culture. Furthermore, preliminary cytocompatibility studies showed that both types of degradable PU are nontoxic, and fibroblasts adhere better and proliferate faster on MIDE containing PU than BD containing PU. To compare the cytocompatibility and degradation behaviors of the synthesized PU with existing FDA approved biocompatible material, polylactide (PLA), with a similar degradation rate, was used as negative control. Two types of PU were shown to have similar cytocompatibility and degradation behaviors as those of the PLA material. To verify the effectiveness of the cytotoxicity assay, latex was used as a positive control. Latex samples showed toxicity to cultured cells as expected. In conclusion, by changing the type of chain extender used during the synthesis of degradable PUs, the degradation rate, mechanical properties, hydrophilicity, and cytophilicity can be adjusted for different tissue engineering applications. (c) 2006 Wiley Periodicals, Inc.