J-2X Gas Generator Development Testing at NASA Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

Reynolds, D. C.; Hormonzian, Carlo

2010-01-01

NASA is developing a liquid oxygen/liquid hydrogen rocket engine for upper stage and trans-lunar applications of the Ares vehicles for the Constellation program. This engine, designated the J-2X, is a higher pressure, higher thrust variant of the Apollo-era J-2 engine. Development was contracted to Pratt & Whitney Rocketdyne in 2006. Over the past several years, two phases of testing have been completed on the development of the gas generator for the J-2X engine. The hardware has progressed through a variety of workhorse injector, chamber, and feed system configurations. Several of these configurations have resulted in combustion instability of the gas generator assembly. Development of the final configuration of workhorse hardware (which will ultimately be used to verify critical requirements on a component level) has required a balance between changes in the injector and chamber hardware in order to successfully mitigate the combustion instability without sacrificing other engine system requirements. This paper provides an overview of the two completed test series, performed at NASA s Marshall Space Flight Center. The requirements, facility setup, hardware configurations, and test series progression are detailed. Significant levels of analysis have been performed in order to provide design solutions to mitigate the combustion stability issues, and these are briefly covered. Also discussed are the results of analyses related to either anomalous readings or off-nominal testing throughout the two test series.

Predicting the flow & noise of a rotor in a turbulent boundary layer using an actuator disk -- RANS approach

NASA Astrophysics Data System (ADS)

Buono, Armand C.

The numerical method presented in this study attempts to predict the mean, non-uniform flow field upstream of a propeller partially immersed in a thick turbulent boundary layer with an actuator disk using CFD based on RANS in ANSYS FLUENT. Three different configurations, involving an infinitely thin actuator disk in the freestream (Configuration 1), an actuator disk near a wall with a turbulent boundary layer (Configuration 2), and an actuator disk with a hub near a wall with a turbulent boundary layer (Configuration 3), were analyzed for a variety of advance ratios ranging from J = 0.48 to J =1.44. CFD results are shown to be in agreement with previous works and validated with experimental data of reverse flow occurring within the boundary layer above the flat plate upstream of a rotor in the Virginia Tech's Stability Wind Tunnel facility. Results from Configuration 3 will be used in future aero-acoustic computations.

Configuration-controlled Au nanocluster arrays on inverse micelle nano-patterns: versatile platforms for SERS and SPR sensors

NASA Astrophysics Data System (ADS)

Jang, Yoon Hee; Chung, Kyungwha; Quan, Li Na; Špačková, Barbora; Šípová, Hana; Moon, Seyoung; Cho, Won Joon; Shin, Hae-Young; Jang, Yu Jin; Lee, Ji-Eun; Kochuveedu, Saji Thomas; Yoon, Min Ji; Kim, Jihyeon; Yoon, Seokhyun; Kim, Jin Kon; Kim, Donghyun; Homola, Jiří; Kim, Dong Ha

2013-11-01

Nanopatterned 2-dimensional Au nanocluster arrays with controlled configuration are fabricated onto reconstructed nanoporous poly(styrene-block-vinylpyridine) inverse micelle monolayer films. Near-field coupling of localized surface plasmons is studied and compared for disordered and ordered core-centered Au NC arrays. Differences in evolution of the absorption band and field enhancement upon Au nanoparticle adsorption are shown. The experimental results are found to be in good agreement with theoretical studies based on the finite-difference time-domain method and rigorous coupled-wave analysis. The realized Au nanopatterns are exploited as substrates for surface-enhanced Raman scattering and integrated into Kretschmann-type SPR sensors, based on which unprecedented SPR-coupling-type sensors are demonstrated.Nanopatterned 2-dimensional Au nanocluster arrays with controlled configuration are fabricated onto reconstructed nanoporous poly(styrene-block-vinylpyridine) inverse micelle monolayer films. Near-field coupling of localized surface plasmons is studied and compared for disordered and ordered core-centered Au NC arrays. Differences in evolution of the absorption band and field enhancement upon Au nanoparticle adsorption are shown. The experimental results are found to be in good agreement with theoretical studies based on the finite-difference time-domain method and rigorous coupled-wave analysis. The realized Au nanopatterns are exploited as substrates for surface-enhanced Raman scattering and integrated into Kretschmann-type SPR sensors, based on which unprecedented SPR-coupling-type sensors are demonstrated. Electronic supplementary information (ESI) available: TEM image and UV-vis absorption spectrum of citrate-capped Au NPs, AFM images of Au NC arrays on the PS-b-P4VP (41k-24k) template, ImageJ-analyzed results of PS-b-P4VP (41k-24k)-templated Au NC arrays, calculated %-surface coverage values, SEM images of Au NC arrays on the PS-b-P2VP (172k-42k) template for SPR biosensing, corresponding ImageJ-analyzed images by varying the Au NP deposition time and results of image analysis. See DOI: 10.1039/c3nr03860b

Structure of V2AlC studied by theory and experiment

NASA Astrophysics Data System (ADS)

Schneider, Jochen M.; Mertens, Raphael; Music, Denis

2006-01-01

We have studied V2AlC (space group P63/mmc, prototype Cr2AlC) by ab initio calculations. The density of states (DOS) of V2AlC for antiferromagnetic, ferromagnetic, and paramagnetic configurations have been discussed. According to the analysis of DOS and cohesive energy, no significant stability differences between spin-polarized and non-spin-polarized configurations were found. Based on the partial DOS analysis, V2AlC can be classified as a strongly coupled nanolaminate according to our previous work [Z. Sun, D. Music, R. Ahuja, S. Li, and J. M. Schneider, Phys. Rev. B 70, 092102 (2004)]. Furthermore, this phase has been synthesized in the form of thin films by magnetron sputtering. The equilibrium volume, determined by x-ray diffraction, is in good agreement with the theoretical data, implying that ab initio calculations provide an accurate description of V2AlC.

Dictyosphaeric acids A and B: new decalactones from an undescribed Penicillium sp. obtained from the alga Dictyosphaeria versluyii.

PubMed

Bugni, Tim S; Janso, Jeffrey E; Williamson, R Thomas; Feng, Xidong; Bernan, Valerie S; Greenstein, Michael; Carter, Guy T; Maiese, William M; Ireland, Chris M

2004-08-01

Fungal isolate F01V25 was obtained from the alga Dictyosphaeria versluyii collected near Dravuni, Fiji, in 2001 and represented a previously undescribed Penicillium sp. Fermentation of isolate F01V25 resulted in the production of two new polyketides, dictyosphaeric acids A and B, along with the known anthraquinone carviolin. The relative stereochemistry of dictyosphaeric acids A and B was determined using the J-based configuration analysis method in conjunction with ROE and NOE correlations.

Simultaneous Vibration Suppression and Energy Harvesting

DTIC Science & Technology

2013-08-15

D.J., 2011. “Modeling and Analysis of Piezoelectric Energy Harvesting from Aeroelastic Vibrations Using the Doublet-Lattice Method,” ASME Journal...Friswell, M. I., and Inman, D. J., 2009, “ Piezoelectric Energy Harvesting from Broadband Random Vibrations ,” Smart Materials and Structures, Vol. 18...and Electrode Configuration on Piezoelectric Energy Harvesting from Cantilevered Beams,” ASME Journal of Vibration and Acoustics, Vol. 131, No. 1, pp

Familiarity from the configuration of objects in 3-dimensional space and its relation to déjà vu: a virtual reality investigation.

PubMed

Cleary, Anne M; Brown, Alan S; Sawyer, Benjamin D; Nomi, Jason S; Ajoku, Adaeze C; Ryals, Anthony J

2012-06-01

Déjà vu is the striking sense that the present situation feels familiar, alongside the realization that it has to be new. According to the Gestalt familiarity hypothesis, déjà vu results when the configuration of elements within a scene maps onto a configuration previously seen, but the previous scene fails to come to mind. We examined this using virtual reality (VR) technology. When a new immersive VR scene resembled a previously-viewed scene in its configuration but people failed to recall the previously-viewed scene, familiarity ratings and reports of déjà vu were indeed higher than for completely novel scenes. People also exhibited the contrasting sense of newness and of familiarity that is characteristic of déjà vu. Familiarity ratings and déjà vu reports among scenes recognized as new increased with increasing feature-match of a scene to one stored in memory, suggesting that feature-matching can produce familiarity and déjà vu when recall fails. Copyright © 2012 Elsevier Inc. All rights reserved.

Structure of V{sub 2}AlC studied by theory and experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schneider, Jochen M.; Mertens, Raphael; Music, Denis

2006-01-01

We have studied V{sub 2}AlC (space group P6{sub 3}/mmc, prototype Cr{sub 2}AlC) by ab initio calculations. The density of states (DOS) of V{sub 2}AlC for antiferromagnetic, ferromagnetic, and paramagnetic configurations have been discussed. According to the analysis of DOS and cohesive energy, no significant stability differences between spin-polarized and non-spin-polarized configurations were found. Based on the partial DOS analysis, V{sub 2}AlC can be classified as a strongly coupled nanolaminate according to our previous work [Z. Sun, D. Music, R. Ahuja, S. Li, and J. M. Schneider, Phys. Rev. B 70, 092102 (2004)]. Furthermore, this phase has been synthesized in themore » form of thin films by magnetron sputtering. The equilibrium volume, determined by x-ray diffraction, is in good agreement with the theoretical data, implying that ab initio calculations provide an accurate description of V{sub 2}AlC.« less

Configurational assignments of conformationally restricted bis-monoterpene hydroquinones: utility in exploration of endangered plants.

PubMed

Oh, Joonseok; Bowling, John J; Zou, Yike; Chittiboyina, Amar G; Doerksen, Robert J; Ferreira, Daneel; Leininger, Theodor D; Hamann, Mark T

2013-08-01

Endangered plant species are an important resource for new chemistry. Lindera melissifolia is native to the Southeastern U.S. and scarcely populates the edges of lakes and ponds. Quantum mechanics (QM) used in combination with NMR/ECD is a powerful tool for the assignment of absolute configuration in lieu of X-ray crystallography. The EtOAc extract of L. melissifolia was subject to chromatographic analysis by VLC and HPLC. Spin-spin coupling constant (SSCC) were calculated using DFT at the MPW1PW91/6-31G(d,p) level for all staggered rotamers. ECD calculations employed Amber* force fields followed by PM6 semi-empirical optimizations. Hetero- and homo-nuclear coupling constants were extracted from 1D (1)H, E.COSY and HETLOC experiments. Two meroterpenoids, melissifolianes A (1) and B (2) were purified and their 2-D structures elucidated using NMR and HRESIMS. The relative configuration of 1 was established using the combination of NOE-based distance restraints and the comparisons of experimental and calculated SSCCs. The comparison of calculated and experimental ECD assigned the absolute configuration of 1. The relative configuration of a racemic mixture, melissifoliane B (2) was established utilizing J-based analysis combined with QM and NMR techniques.Conclusion Our study of the Lindera melissifolia metabolome exemplifies how new chemistry remains undiscovered among the numerous endangered plant species and demonstrates how analysis by ECD and NMR combined with various QM calculations is a sensible approach to support the stereochemical assignment of molecules with conformationally restricted conformations. QM-NMR/ECD combined approaches are of utility for unambiguous assignment of 3-D structures, especially with limited plant material and when a molecule is conformationally restricted. Conservation of an endangered plant species can be supported through identification of its new chemistry and utilization of that chemistry for commercial purposes. Copyright © 2013. Published by Elsevier B.V.

Density functional theory calculations in stereochemical determination of terpecurcumins J-W, cytotoxic terpene-conjugated curcuminoids from Curcuma longa L.

PubMed

Lin, Xionghao; Ji, Shuai; Qiao, Xue; Hu, Hongbo; Chen, Ni; Dong, Yinhui; Huang, Yun; Guo, Dean; Tu, Pengfei; Ye, Min

2013-12-06

Fourteen novel terpene-conjugated curcuminoids, terpecurcumins J-W (1-14), have been isolated from the rhizomes of Curcuma longa L. Among them, terpecurcumins J-Q and V represent four unprecedented skeletons featuring an unusual core of hydrobenzannulated[6,6]-spiroketal (1 and 2), bicyclo[2.2.2]octene (3-7), bicyclo[3.1.3]octene (8), and spiroepoxide (13), respectively. The structures of compounds 1-14 were elucidated by extensive spectroscopic analysis, and their absolute configurations were established by electronic circular dichroism, vibrational circular dichroism, and (13)C NMR spectroscopic data analysis, together with density functional theory calculations. The structure and configuration of 1 was further confirmed by single-crystal X-ray diffraction (Cu Kα). The biogenetic pathways of 1-14 were proposed, involving Michael addition, condensation, Diels-Alder cycloaddition, and electrophilic substitution reactions. Terpecurcumins showed more potent cytotoxic activities than curcumin and ar-/β-turmerone. Among them, terpecurcumin Q (8) exhibited IC50 of 3.9 μM against MCF-7 human breast cancer cells, and mitochondria-mediated apoptosis played an important role in the overall growth inhibition. Finally, LC/MS/MS quantitative analysis of five representative terpecurcumins indicated these novel compounds were present in C. longa at parts per million level.

Signal Processing Methods for Liquid Rocket Engine Combustion Stability Assessments

NASA Technical Reports Server (NTRS)

Kenny, R. Jeremy; Lee, Erik; Hulka, James R.; Casiano, Matthew

2011-01-01

The J2X Gas Generator engine design specifications include dynamic, spontaneous, and broadband combustion stability requirements. These requirements are verified empirically based high frequency chamber pressure measurements and analyses. Dynamic stability is determined with the dynamic pressure response due to an artificial perturbation of the combustion chamber pressure (bomb testing), and spontaneous and broadband stability are determined from the dynamic pressure responses during steady operation starting at specified power levels. J2X Workhorse Gas Generator testing included bomb tests with multiple hardware configurations and operating conditions, including a configuration used explicitly for engine verification test series. This work covers signal processing techniques developed at Marshall Space Flight Center (MSFC) to help assess engine design stability requirements. Dynamic stability assessments were performed following both the CPIA 655 guidelines and a MSFC in-house developed statistical-based approach. The statistical approach was developed to better verify when the dynamic pressure amplitudes corresponding to a particular frequency returned back to pre-bomb characteristics. This was accomplished by first determining the statistical characteristics of the pre-bomb dynamic levels. The pre-bomb statistical characterization provided 95% coverage bounds; these bounds were used as a quantitative measure to determine when the post-bomb signal returned to pre-bomb conditions. The time for post-bomb levels to acceptably return to pre-bomb levels was compared to the dominant frequency-dependent time recommended by CPIA 655. Results for multiple test configurations, including stable and unstable configurations, were reviewed. Spontaneous stability was assessed using two processes: 1) characterization of the ratio of the peak response amplitudes to the excited chamber acoustic mode amplitudes and 2) characterization of the variability of the peak response's frequency over the test duration. This characterization process assists in evaluating the discreteness of a signal as well as the stability of the chamber response. Broadband stability was assessed using a running root-mean-square evaluation. These techniques were also employed, in a comparative analysis, on available Fastrac data, and these results are presented here.

Sulfur mustard gas adsorption on ZnO fullerene-like nanocage: Quantum chemical calculations

NASA Astrophysics Data System (ADS)

Kazemi, Mohammad; Rad, Ali Shokuhi

2017-06-01

In the present study, we used density functional theory calculations (at B3LYP and ωB97XD Levels) to search on the adsorption of Sulfur mustard gas (defined as mustard gas) on the surface of fullerene-like ZnO nanocage as a semiconductor. We found three different configurations of adsorbed gas on the surface of this nanostructure semiconductor. The values of adsorption energy of mustard gas are calculated in the range of -144∼ -200 kJ/mol with enthalpies in the range of -132∼-195 kJ/mol and Gibbs free energies in the range of -88∼-144 kJ/mol (T = 298 K, based on ωB97XD level), which indicate exothermic and spontaneous chemisorption. For all geometries, we calculated geometry parameters by taking into account the charge analysis and frontier molecular orbital study. The result of this study can be a support for next studies to develop new nanomaterials as adsorbent/sensor for mustard gas.

Large-area sheet task advanced dendritic web growth development

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Schruben, J.

1982-01-01

The computer code for calculating web temperature distribution was expanded to provide a graphics output in addition to numerical and punch card output. The new code was used to examine various modifications of the J419 configuration and, on the basis of the results, a new growth geometry was designed. Additionally, several mathematically defined temperature profiles were evaluated for the effects of the free boundary (growth front) on the thermal stress generation. Experimental growth runs were made with modified J419 configurations to complement the modeling work. A modified J435 configuration was evaluated.

Large-area sheet task advanced dendritic web growth development

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Schruben, J.

1982-01-01

The "discrete shield' temperature model was completed and verified. Modifications to the J419 low stress configuration were tested experimentally to evaluate effects on growth speed. A composite lid and shield configuration combining the low stress features of the J419 with the width limiting characteristics of the J98M3 was fabricated and tested in the N-furnace. Several long crystals were grown with width limited to about 3.3 cm and with melt replenishment, although the configuration is not yet optimized for steady state growth.

Laser ignition of an experimental combustion chamber with a multi-injector configuration at low pressure conditions

NASA Astrophysics Data System (ADS)

Börner, Michael; Manfletti, Chiara; Kroupa, Gerhard; Oschwald, Michael

2017-09-01

In search of reliable and light-weight ignition systems for re-ignitable upper stage engines, a laser ignition system was adapted and tested on an experimental combustion chamber for propellant injection into low combustion chamber pressures at 50-80 mbar. The injector head pattern consisted of five coaxial injector elements. Both, laser-ablation-driven ignition and laser-plasma-driven ignition were tested for the propellant combination liquid oxygen and gaseous hydrogen. The 122 test runs demonstrated the reliability of the ignition system for different ignition configurations and negligible degradation due to testing. For the laser-plasma-driven scheme, minimum laser pulse energies needed for 100% ignition probability were found to decrease when increasing the distance of the ignition location from the injector faceplate with a minimum of 2.6 mJ. For laser-ablation-driven ignition, the minimum pulse energy was found to be independent of the ablation material tested and was about 1.7 mJ. The ignition process was characterized using both high-speed Schlieren and OH* emission diagnostics. Based on these findings and on the increased fiber-based pulse transport capabilities recently published, new ignition system configurations for space propulsion systems relying on fiber-based pulse delivery are formulated. If the laser ignition system delivers enough pulse energy, the laser-plasma-driven configuration represents the more versatile configuration. If the laser ignition pulse power is limited, the application of laser-ablation-driven ignition is an option to realize ignition, but implies restrictions concerning the location of ignition.

J3Gen: A PRNG for Low-Cost Passive RFID

PubMed Central

Melià-Seguí, Joan; Garcia-Alfaro, Joaquin; Herrera-Joancomartí, Jordi

2013-01-01

Pseudorandom number generation (PRNG) is the main security tool in low-cost passive radio-frequency identification (RFID) technologies, such as EPC Gen2. We present a lightweight PRNG design for low-cost passive RFID tags, named J3Gen. J3Gen is based on a linear feedback shift register (LFSR) configured with multiple feedback polynomials. The polynomials are alternated during the generation of sequences via a physical source of randomness. J3Gen successfully handles the inherent linearity of LFSR based PRNGs and satisfies the statistical requirements imposed by the EPC Gen2 standard. A hardware implementation of J3Gen is presented and evaluated with regard to different design parameters, defining the key-equivalence security and nonlinearity of the design. The results of a SPICE simulation confirm the power-consumption suitability of the proposal. PMID:23519344

A parametric numerical study of mixing in a cylindrical duct

NASA Astrophysics Data System (ADS)

Oechsle, V. L.; Mongia, H. C.; Holderman, J. D.

1992-07-01

The interaction is described of some of the important parameters affecting the mixing process in a quick mixing region of a rich burn/quick mix/lean burn (RQL) combustor. The performance of the quick mixing region is significantly affected by the geometric designs of both the mixing domain and the jet inlet orifices. Several of the important geometric parameters and operating conditions affecting the mixing process were analytically studied. Parameters such as jet-to-mainstream momentum flux ratio (J), mass flow ratio (MR), orifice geometry, orifice orientation, and number of orifices/row (equally spaced around the circumferential direction were analyzed. Three different sets of orifice shapes were studied: (1) square, (2) elongated slots, and (3) equilateral triangles. Based on the analytical results, the best mixing configuration depends significantly on the penetration depth of the jet to prevent the hot mainstream flow from being entrained behind the orifice. The structure in a circular mixing section is highly weighted toward the outer wall and any mixing structure affecting this area significantly affects the overall results. The increase in the number of orifices per row increases the mixing at higher J conditions. Higher slot slant angles and aspect ratios are generally the best mixing configurations at higher momentum flux ratio (J) conditions. However, the square and triangular shaped orifices were more effective mixing configurations at lower J conditions.

The new insight into dynamic crossover in glass forming liquids from the apparent enthalpy analysis

NASA Astrophysics Data System (ADS)

Martinez-Garcia, Julio Cesar; Martinez-Garcia, Jorge; Rzoska, Sylwester J.; Hulliger, Jürg

2012-08-01

One of the most intriguing phenomena in glass forming systems is the dynamic crossover (TB), occurring well above the glass temperature (Tg). So far, it was estimated mainly from the linearized derivative analysis of the primary relaxation time τ(T) or viscosity η(T) experimental data, originally proposed by Stickel et al. [J. Chem. Phys. 104, 2043 (1996), 10.1063/1.470961; Stickel et al. J. Chem. Phys. 107, 1086 (1997)], 10.1063/1.474456. However, this formal procedure is based on the general validity of the Vogel-Fulcher-Tammann equation, which has been strongly questioned recently [T. Hecksher et al. Nature Phys. 4, 737 (2008), 10.1038/nphys1033; P. Lunkenheimer et al. Phys. Rev. E 81, 051504 (2010), 10.1103/PhysRevE.81.051504; J. C. Martinez-Garcia et al. J. Chem. Phys. 134, 024512 (2011)], 10.1063/1.3514589. We present a qualitatively new way to identify the dynamic crossover based on the apparent enthalpy space (H_a^' = {{dln τ }/{d({1/T})}}) analysis via a new plot ln H_a^' vs. 1/T supported by the Savitzky-Golay filtering procedure for getting an insight into the noise-distorted high order derivatives. It is shown that depending on the ratio between the "virtual" fragility in the high temperature dynamic domain (mhigh) and the "real" fragility at Tg (the low temperature dynamic domain, m = mlow) glass formers can be splitted into two groups related to f < 1 and f > 1, (f = mhigh/mlow). The link of this phenomenon to the ratio between the apparent enthalpy and activation energy as well as the behavior of the configurational entropy is indicated.

Electronic structure, magnetism, and exchange integrals in transition-metal oxides: Role of the spin polarization of the functional in DFT+U calculations

NASA Astrophysics Data System (ADS)

Keshavarz, Samara; Schött, Johan; Millis, Andrew J.; Kvashnin, Yaroslav O.

2018-05-01

Density functional theory augmented with Hubbard-U corrections (DFT+U ) is currently one of the most widely used methods for first-principles electronic structure modeling of insulating transition-metal oxides (TMOs). Since U is relatively large compared to bandwidths, the magnetic excitations in TMOs are expected to be well described by a Heisenberg model. However, in practice the calculated exchange parameters Ji j depend on the magnetic configuration from which they are extracted and on the functional used to compute them. In this work we investigate how the spin polarization dependence of the underlying exchange-correlation functional influences the calculated magnetic exchange constants of TMOs. We perform a systematic study of the predictions of calculations based on the local density approximation plus U (LDA+U ) and the local spin density approximation plus U (LSDA+U ) for the electronic structures, total energies, and magnetic exchange interactions Ji j extracted from ferromagnetic (FM) and antiferromagnetic (AFM) configurations of several transition-metal oxide materials. We report that for realistic choices of Hubbard U and Hund's J parameters, LSDA+U and LDA+U calculations result in different values of the magnetic exchange constants and band gap. The dependence of the band gap on the magnetic configuration is stronger in LDA+U than in LSDA+U and we argue that this is the main reason why the configuration dependence of Ji j is found to be systematically more pronounced in LDA+U than in LSDA+U calculations. We report a very good correspondence between the computed total energies and the parametrized Heisenberg model for LDA+U calculations, but not for LSDA+U , suggesting that LDA+U is a more appropriate method for estimating exchange interactions.

The J-2X Fuel Turbopump - Design, Development, and Test

NASA Technical Reports Server (NTRS)

Tellier, James G.; Hawkins, Lakiesha V.; Shinguchi, Brian H.; Marsh, Matthew W.

2011-01-01

Pratt and Whitney Rocketdyne (PWR), a NASA subcontractor, is executing the design, development, test, and evaluation (DDT&E) of a liquid oxygen, liquid hydrogen two hundred ninety four thousand pound thrust rocket engine initially intended for the Upper Stage (US) and Earth Departure Stage (EDS) of the Constellation Program Ares-I Crew Launch Vehicle (CLV). A key element of the design approach was to base the new J-2X engine on the heritage J-2S engine with the intent of uprating the engine and incorporating SSME and RS-68 lessons learned. The J-2S engine was a design upgrade of the flight proven J-2 configuration used to put American astronauts on the moon. The J-2S Fuel Turbopump (FTP) was the first Rocketdyne-designed liquid hydrogen centrifugal pump and provided many of the early lessons learned for the Space Shuttle Main Engine High Pressure Fuel Turbopumps. This paper will discuss the design trades and analyses performed for the current J-2X FTP to increase turbine life; increase structural margins, facilitate component fabrication; expedite turbopump assembly; and increase rotordynamic stability margins. Risk mitigation tests including inducer water tests, whirligig turbine blade tests, turbine air rig tests, and workhorse gas generator tests characterized operating environments, drove design modifications, or identified performance impact. Engineering design, fabrication, analysis, and assembly activities support FTP readiness for the first J-2X engine test scheduled for July 2011.

Zero-moment point determination of worst-case manoeuvres leading to vehicle wheel lift

NASA Astrophysics Data System (ADS)

Lapapong, S.; Brown, A. A.; Swanson, K. S.; Brennan, S. N.

2012-01-01

This paper proposes a method to evaluate vehicle rollover propensity based on a frequency-domain representation of the zero-moment point (ZMP). Unlike other rollover metrics such as the static stability factor, which is based on the steady-state behaviour, and the load transfer ratio, which requires the calculation of tyre forces, the ZMP is based on a simplified kinematic model of the vehicle and the analysis of the contact point of the vehicle relative to the edge of the support polygon. Previous work has validated the use of the ZMP experimentally in its ability to predict wheel lift in the time domain. This work explores the use of the ZMP in the frequency domain to allow a chassis designer to understand how operating conditions and vehicle parameters affect rollover propensity. The ZMP analysis is then extended to calculate worst-case sinusoidal manoeuvres that lead to untripped wheel lift, and the analysis is tested across several vehicle configurations and compared with that of the standard Toyota J manoeuvre.

Missions and Mobility Configurations for RED HORSE

DTIC Science & Technology

1988-04-01

use in other research reports or educational pursuits contingent upon the following stipulations: - Reproduction rights do not extend to any copyrighted...MOBILITY CONFIGURATIONS FOR RED HORSE AUTHOR(S) MAJOR JAMES T. RYBURN, USAF FACULTY ADVISOR LT COL ROBERT L. PETERS, ACSC/3823 STUS SPONSOR COL ROBERT J...Classification) MISSIONS AND MOBILITY CONFIGURATIONS FOR RED HORSE 12. PERSONAL AUTHOR(S) Ryburn, James T., Maj or, USAF 13a. TYPE OF REPORT J13b. TIME

Advances in the evaluation of wind-induced undercatch using CFD-based simulations of snow gauge performance

NASA Astrophysics Data System (ADS)

Colli, Matteo; Lanza, Luca; Rasmussen, Roy; Thériault, Julie

2016-04-01

Despite its importance, accurate measurements of precipitation remains a challenge. Measurement errors for solid precipitation, which are often ignored for automated systems, frequently range from 20% to 70% due to undercatch in windy conditions. While solid precipitation measurements have been the subject of many studies, there have been only a limited number of numerical modeling efforts to estimate the collection efficiency of solid precipitation gauges when exposed to the wind, in both shielded and unshielded configurations. The available models use CFD simulations of the airflow pattern generated by the aerodynamic response of the gauge/shield geometry to perform the Lagrangian tracking of solid precipitation particles (Thériault et al., 2012; Colli et al. 2016a and 2016b). Validation of the results against field observations yields similarities in the overall behavior, but the model output only approximately reproduces the dependence of the experimental collection efficiency on wind speed. We present recent developments of such a modelling approach including various gauge/shield configurations, the influence of the drag coefficient calculation on the model performance, and the role of the particle size distribution in explaining the scatter of the collection efficiency observed at any particular wind speed (Colli et al. 2015). Comparison with observations at the Marshall (CO) field test site is used to validate results of the various modelling schemes and to support the analysis of the microphysical characteristics of ice crystals. References: Colli, M., Rasmussen, R.M., Thèriault, J.M., Lanza, L.G., Baker, B.C. and J. Kochendorfer (2015). An improved trajectory model to evaluate the collection performance of snow gauges. J.Appl.Meteor.Climatol., 54(8), pages 1826-1836. Colli, M., Lanza, L.G., Rasmussen, R.M. and J.M. Thèriault (2016a). The collection efficiency of shielded and unshielded precipitation gauges. Part I: CFD airflow modelling. J. of Hydrometeorol., 17(1), pages 231-243. Colli, M., Lanza, L.G., Rasmussen, R.M. and J.M. Thèriault (2016b). The collection efficiency of shielded and unshielded precipitation gauges. Part II: modelling particle trajectories. J. of Hydrometeorol., 17(1), 245-255. Thériault, J. M., R. Rasmussen, K. Ikeda, and S. Landolt, (2012). Dependence of snow gauge collection efficiency on snowflake characteristics. J. Appl. Meteor. Climatol., 51, 745-762.

Real-Time Communication Systems: Design, Analysis and Implementation

DTIC Science & Technology

1984-07-31

sively [141-[19). A two-hop configuration involving a ring of repeaters around a station has been analyzed by Gitman [20) ; STATION network capacity...control of the packet-switching broadcast channels," J. Ass. Comput Mach., vol. 24, pp. 375-386, July 1977. [201 I. Gitman , "On the capacity of

On the existence of a solution to a quasilinear elliptic system of the Lane, Emden and Fowler type

NASA Astrophysics Data System (ADS)

Covei, Dragoş-Pǎtru

2012-11-01

In this article, we give an algorithm to obtain the existence of a solution for a quasilinear elliptic system. Our result is new and is based on a recent work of [R.J. Biezuner, J. Brown, G. Ercole and E.M. Martins, Computing the first eigenpair of the p-Laplacian via inverse iteration of sublinear supersolutions, J. Sci. Computation, 2011]. Such problems appear in boundary layer phenomena for viscous fluids, the equilibrium configuration of mass in a spherical cloud of gas, thermal explosion as well as in others applications.

CFD Mixing Analysis of Jets Injected from Straight and Slanted Slots into Confined Crossflow in Rectangular Ducts

NASA Technical Reports Server (NTRS)

Bain, D. B.; Smith, C. E.; Holdeman, J. D.

1992-01-01

A CFD study was performed to analyze the mixing potential of opposed rows of staggered jets injected into confined crossflow in a rectangular duct. Three jet configurations were numerically tested: (1) straight (0 deg) slots; (2) perpendicular slanted (45 deg) slots angled in opposite directions on top and bottom walls; and (3) parallel slanted (45 deg) slots angled in the same direction on top and bottom walls. All three configurations were tested at slot spacing-to-duct height ratios (S/H) of 0.5, 0.75, and 1.0; a jet-to-mainstream momentum flux ratio (J) of 100; and a jet-to-mainstream mass flow ratio of 0.383. Each configuration had its best mixing performance at S/H of 0.75. Asymmetric flow patterns were expected and predicted for all slanted slot configurations. The parallel slanted slot configuration was the best overall configuration at x/H of 1.0 for S/H of 0.75.

Complex Convective Thermal Fluxes and Vorticity Structure

NASA Astrophysics Data System (ADS)

Redondo, Jose M.; Tellez, Jackson; Sotillos, Laura; Lopez Gonzalez-Nieto, Pilar; Sanchez, Jesus M.; Furmanek, Petr; Diez, Margarita

2015-04-01

Local Diffusion and the topological structure of vorticity and velocity fields is measured in the transition from a homogeneous linearly stratified fluid to a cellular or layered structure by means of convective cooling and/or heating[1,2]. Patterns arise by setting up a convective flow generated by an array of Thermoelectric devices (Peltier/Seebeck cells) these are controlled by thermal PID generating a buoyant heat flux [2]. The experiments described here investigate high Prandtl number mixing using brine and fresh water in order to form density interfaces and low Prandtl number mixing with temperature gradients. The set of dimensionless parameters define conditions of numeric and small scale laboratory modeling of environmental flows. Fields of velocity, density and their gradients were computed and visualized [3,4]. When convective heating and cooling takes place the combination of internal waves and buoyant turbulence is much more complicated if the Rayleigh and Reynolds numbers are high in order to study entrainment and mixing. Using ESS and selfsimilarity structures in the velocity and vorticity fieds and intermittency [3,5] that forms in the non-homogeneous flow is related to mixing and stiring. The evolution of the mixing fronts are compared and the topological characteristics of the merging of plumes and jets in different configurations presenting detailed comparison of the evolution of RM and RT, Jets and Plumes in overall mixing. The relation between structure functions, fractal analysis and spectral analysis can be very useful to determine the evolution of scales. Experimental and numerical results on the advance of a mixing or nonmixing front occurring at a density interface due to body forces [6]and gravitational acceleration are analyzed considering the fractal and spectral structure of the fronts like in removable plate experiments for Rayleigh-Taylor flows. The evolution of the turbulent mixing layer and its complex configuration is studied taking into account the dependence on the initial modes at the early stages and its spectral, self-similar information [3,7-9]. Spectral and Fractal analysis on the images has been used in order to estimate dominant mixing structures as well as the dispersion relations of basic instabilities [4,8. Comparison of the range of entrainment values from laboratory experiments with those ocurring in nature, both in the atmosphere and ocean or in Astrophysics shows the importance of modeling correctly the integral lengthscales of the turbulence. The Entrainment may actually be related to the ratio of the flux to gradient Richardson numbers as well as the Turbulent Schmidt or Prandtl number [6,8] and their structure functions [5]. Turbulent mixing diagnostics are based on schlieren and shadowgraph visualization, planar laser sheet, laser Doppler velocimetry (LDV) and particle image velocimetry (PIV). We are interested by the influence of initial conditions [9](flux gradients of various sizes) on the transition to turbulent mixing, the influence of subsequent vortices and waves, initially in a one dimensional or plane configuration and furthermore in a two-three dimensional configuration with the interface oblique with respect to the horizontal. [1] Redondo J.M. (1992) Termodinámica de los procesos irreversibles, efectos termoeléctricos Rev. Termoelectricidad 2, 16-29.AIT.Pamplona. [2] Redondo J.M., Sanchez J.M. Pascual I. Noriega,G.F.(1995).Thermoelectric regulation for electric cabinets. XVI International Conference in Thermoelectrics, 02-G20. Ed. V. Vedernikov. 456-468. St. Petersburg, Russia. [3] Nicolleau, F.C.G.A.; Cambon, C.; Redondo, J.M.; Vassilicos, J.C.; Reeks, M.; Nowakowski, A.F. (Eds.)(2012) New Approaches in Modeling Multiphase Flows and Dispersion in Turbulence, Fractal Methods and Synthetic Turbulence. ERCOFTAC Series. [4] Redondo J M, Sanchez M A and Cantalapiedra I R (1995). Turbulent Mechanisms in Stratified Flows, Dynamics of Atmospheres and Oceans, 23, 454-462. [5] Mahjoub O.B., Redondo J.M. and Babiano A.(2000) Hyerarchy flux in nonhomogeneous flows in Turbulent diffusion in the environment Eds. Redondo J.M. and Babiano A. 249-260. [6] Matulka A., Redondo J.M. and Carrillo A.(2008) Experiments in stratified and rotating decaying 2D flows, Il Nuovo Cimento 31, 5-6, 757-770. 2008. [7]Fraunie P., Berreba S. Chashechkin Yu.D., Velasco D. and Redondo J.M. (2008) Large eddy simulation and laboratory experiments on the decay of grid wakes in strongly stratified flows. Il Nuovo Cimento C 31, 909-930. [8]Matulka, A., López, P., Redondo, J. M., and Tarquis, A.(2014) On the entrainment coefficient in a forced plume: quantitative effects of source parameters, Nonlin. Processes Geophys., 21, 269-278. [9] Castilla R., Oñate E. and Redondo J.M. (2007) Models, Experiments and Computations in Turbulence. CIMNE, Barcelona, 255.

Millijoule-level 20 ps Nd:YAG oscillator-amplifier laser system for investigation of stimulated Raman scattering and optical parametric generation

NASA Astrophysics Data System (ADS)

Jelínek, Michal; Kubecek, Vàclav

2012-06-01

We report on quasi-continuously pumped oscillator-amplifier laser system. The laser oscillator was based on highly 2.4 at.% doped crystalline Nd:YAG in a bounce geometry and passively mode locked by a semiconductor saturable absorber mirror. Using the cavity dumping technique, 19 ps pulses with the energy of 20 μJ and Gaussian spatial beam profile were generated directly from the oscillator at the repetition rate up to 50 Hz. For applications requiring more energetic pulses the amplification was studied using either an identical highly doped Nd:YAG module in bounce geometry or flashlamp pumped Nd:YAG laser rod. Using compact all diode pumped oscillator-amplifier system, 130 μJ pulses were generated. The flashlamp pumped amplifier with 100 mm long Nd:YAG enabled to obtain higher energy. In the single pass configuration the pulse was amplified to 4.5 mJ, using the double pass configuration the pulse energy was further increased up to 20 mJ with the duration of 25 ps at 10 Hz. The developed laser system was used for investigation of stimulated Raman scattering in Strontium Barium Niobate and optical parametric generation in CdSiP2.

Atomic lifetime measurements of Ne-like Fe ions in a magnetic field

DOE PAGES

Trabert, E.; Beiersdorfer, P.; Crespo Lopez-Urrutia, J. R.

2017-04-18

Among the lowest excited levels in Ne-like ions, that is, of configuration 2p 53s, there is a J = 0 level that in a field-free environment decays by a magnetic dipole (M1) transition to the lower J = 1 level of the same configuration only. In the presence of a magnetic field, this level can also decay to the ground configuration J = 0 level. In the course of the first measurement of the 2p 53s J = 0 level lifetime and the M1 transition rate the magnetically induced transition (MIT) appeared as a complication that was then turned intomore » a tool. The technical details of the measurement in an electron beam ion trap have been described elsewhere. As a result, we illuminate the physics aspects of the two transition rate measurements and show how the results compare to computations.« less

Wind velocity measurement accuracy with highly stable 12 mJ/pulse high repetition rate CO2 laser master oscillator power amplifier

NASA Technical Reports Server (NTRS)

Bilbro, James W.; Johnson, Steven C.; Rothermel, Jeffry

1987-01-01

A coherent CO2 lidar operating in a master oscillator power amplifier configuration (MOPA) is described for both ground-based and airborne operation. Representative data taken from measurements against stationary targets in both the ground-based and airborne configurations are shown for the evaluation of the frequency stability of the system. Examples of data are also given which show the results of anomalous system operation. Overall results demonstrate that velocity measurements can be performed consistently to an accuracy of + or - 0.5 m/s and in some cases + or - 0.1 m/s.

Oligoclonal T cell receptor gene rearrangements in blood lymphocytes of patients with acute Epstein-Barr virus-induced infectious mononucleosis.

PubMed Central

Strickler, J G; Movahed, L A; Gajl-Peczalska, K J; Horwitz, C A; Brunning, R D; Weiss, L M

1990-01-01

Gene rearrangement studies were performed on blood lymphocytes from eight patients with acute Epstein-Barr virus-induced infectious mononucleosis. The diagnosis in each case was based on characteristic clinical, hematologic, and serologic findings. The blood lymphocytes in each patient consisted predominantly of CD8+ T cells. EBV DNA was detected in seven patients by Southern blot analysis (EBV Bam HI W probe, Bam HI). A germline configuration was found for the immunoglobulin heavy and light chain genes (JH probe, Bam HI and Eco RI; C kappa probe, Bam HI; and C lambda probe, Eco RI). T cell receptor gene rearrangements were detected with J gamma and J beta 1 + 2 probes. Using a J gamma probe with two different restriction enzymes (Bgl II and Eco RI), the blood from each patient showed several bands corresponding to the polyclonal pattern previously described in the blood of normal individuals. Using J beta 1 + 2 probes with two different restriction enzymes (Bgl II and Bam HI), each case showed from 3 to about 12 extragermline bands of varying intensity and in different locations from case to case. In addition, each case showed relative deletion of the J beta 1 germline band. This oligoclonal pattern of T cell receptor gene rearrangements has not been previously reported in benign or malignant T cell populations. Images PMID:2170451

Sub-Scale Testing and Development of the J-2X Fuel Turbopump Inducer

NASA Technical Reports Server (NTRS)

Sargent, Scott R.; Becht, David G.

2011-01-01

In the early stages of the J-2X upper stage engine program, various inducer configurations proposed for use in the fuel turbopump (FTP) were tested in water. The primary objectives of this test effort were twofold. First, to obtain a more comprehensive data set than that which existed in the Pratt & Whitney Rocketdyne (PWR) historical archives from the original J-2S program, and second, to supplement that data set with information regarding the cavitation induced vibrations for both the historical J-2S configuration as well as those tested for the J-2X program. The J-2X FTP inducer, which actually consists of an inducer stage mechanically attached to a kicker stage, underwent 4 primary iterations utilizing sub-scaled test articles manufactured and tested in PWR's Engineering Development Laboratory (EDL). The kicker remained unchanged throughout the test series. The four inducer configurations tested retained many of the basic design features of the J-2S inducer, but also included variations on leading edge blade thickness and blade angle distribution, primarily aimed at improving suction performance at higher flow coefficients. From these data sets, the effects of the tested design variables on hydrodynamic performance and cavitation instabilities were discerned. A limited comparison of impact to the inducer efficiency was determined as well.

Posture Detection Based on Smart Cushion for Wheelchair Users

PubMed Central

Ma, Congcong; Li, Wenfeng; Gravina, Raffaele; Fortino, Giancarlo

2017-01-01

The postures of wheelchair users can reveal their sitting habit, mood, and even predict health risks such as pressure ulcers or lower back pain. Mining the hidden information of the postures can reveal their wellness and general health conditions. In this paper, a cushion-based posture recognition system is used to process pressure sensor signals for the detection of user’s posture in the wheelchair. The proposed posture detection method is composed of three main steps: data level classification for posture detection, backward selection of sensor configuration, and recognition results compared with previous literature. Five supervised classification techniques—Decision Tree (J48), Support Vector Machines (SVM), Multilayer Perceptron (MLP), Naive Bayes, and k-Nearest Neighbor (k-NN)—are compared in terms of classification accuracy, precision, recall, and F-measure. Results indicate that the J48 classifier provides the highest accuracy compared to other techniques. The backward selection method was used to determine the best sensor deployment configuration of the wheelchair. Several kinds of pressure sensor deployments are compared and our new method of deployment is shown to better detect postures of the wheelchair users. Performance analysis also took into account the Body Mass Index (BMI), useful for evaluating the robustness of the method across individual physical differences. Results show that our proposed sensor deployment is effective, achieving 99.47% posture recognition accuracy. Our proposed method is very competitive for posture recognition and robust in comparison with other former research. Accurate posture detection represents a fundamental basic block to develop several applications, including fatigue estimation and activity level assessment. PMID:28353684

Propagation of Polarization Modulated Beams Through a Turbulent Atmosphere

DTIC Science & Technology

2014-11-24

Clifford Algebra to Geometric Calculus , Reidel, 1984. Hirschfelder, J.O., Curtiss, C.F. & Bird, R.B., Molecular Theory of Gases and Liquids, Wiley, 1954...are made explicit in a Poincaré sphere and geometric (Clifford) algebra representation. Section 5.0 of this report provides the evidence supporting...MEDIA 4.0 LABORATORY TEST CONFIGURATIONS 5.0 TEST RESULTS 5.1 DATA ANALYSIS METHODS 5.2 DATA ANALYSIS 6.0 GEOMETRIC ALGEBRA 6.1 INTRODUCTION

Highly oxygenated ent-pimarane-type diterpenoids from the Chinese liverwort Pedinophyllum interruptum and their allelopathic activities.

PubMed

Liu, Na; Li, Rui-Juan; Wang, Xiao-Ning; Zhu, Rong-Xiu; Wang, Lei; Lin, Zhao-Min; Zhao, Yu; Lou, Hong-Xiang

2013-09-27

Ten highly oxygenated ent-pimarane-type diterpenoids, pedinophyllols A-J (1-10), were isolated from the Chinese liverwort Pedinophyllum interruptum. Their structures were determined by comprehensive analysis of spectroscopic data together with single-crystal X-ray diffraction analysis. The absolute configurations were elucidated by comparison of experimental and theoretically calculated electronic circular dichroism spectra. Allelopathic testing showed that several new diterpenoids inhibited germination of Arabidopsis thaliana seeds.

Vaccinols J-S, ten new salicyloid derivatives from the marine mangrove-derived endophytic fungus Pestalotiopsis vaccinii.

PubMed

Wang, Jun-Feng; Liang, Rui; Liao, Sheng-Rong; Yang, Bin; Tu, Zheng-Chao; Lin, Xiu-Ping; Wang, Bin-Gui; Liu, Yonghong

2017-07-01

Ten new salicyloid derivatives, namely vaccinols J-S (1-10), along with five known compounds (11-15) were isolated from Pestalotiopsis vaccinii (cgmcc3.9199) endogenous with the mangrove plant Kandelia candel (L.) Druce (Rhizophoraceae). Their structures including absolute configurations were established on the basis of spectroscopic analysis, optical rotation, CD spectra, quantum ECD calculations. To the best of our knowledge, vaccinol J (1) is the first example of salicyloid derivatives containing 2-methylfuran moiety. All of the new compounds were tested for their anti-enterovirus 7l (EV71) and cytotoxic activities. Among them, vaccinol J (1) exhibited in vitro anti-EV71 with IC 50 value of 30.7μM (IC 50 177.0μM for the positive control ribavirin). Copyright © 2017. Published by Elsevier B.V.

VizieR Online Data Catalog: An ALMA survey of ECDFS submillimeter galaxies (Simpson+, 2014)

NASA Astrophysics Data System (ADS)

Simpson, J. M.; Swinbank, A. M.; Smail, I.; Alexander, D. M.; Brandt, W. N.; Bertoldi, F.; De Breuck, C.; Chapman, S. C.; Coppin, K. E. K.; da Cunha, E.; Danielson, A. L. R.; Dannerbauer, H.; Greve, T. R.; Hodge, J. A.; Ivison, R. J.; Karim, A.; Knudsen, K. K.; Poggianti, B. M.; Schinnerer, E.; Thomson, A. P.; Walter, F.; Wardlow, J. L.; Weiss, A.; van der Werf, P. P.

2017-07-01

In this study we undertake a multi-wavelength analysis of the ALMA-detected submm galaxies from the catalog presented by Hodge et al. (2013, J/ApJ/768/91) (see also Karim et al. 2013MNRAS.432....2K). To briefly summarize the observations, we obtained 120 s integrations of 122 of the original 126 LESS submm sources, initially identified using the LABOCA camera on the APEX telescope (Weiss et al. 2009, J/ApJ/707/1201). These Cycle 0 observations used the compact configuration, yielding a median synthesized beam of ~1.6"x1.2". The observing frequency was matched to the original LESS survey, 344 GHz (Band 7), and we reach a typical rms across our velocity-integrated maps of 0.4 mJy/beam. (3 data files).

Two-Dimensional Anisotropic Random Walks: Fixed Versus Random Column Configurations for Transport Phenomena

NASA Astrophysics Data System (ADS)

Csáki, Endre; Csörgő, Miklós; Földes, Antónia; Révész, Pál

2018-04-01

We consider random walks on the square lattice of the plane along the lines of Heyde (J Stat Phys 27:721-730, 1982, Stochastic processes, Springer, New York, 1993) and den Hollander (J Stat Phys 75:891-918, 1994), whose studies have in part been inspired by the so-called transport phenomena of statistical physics. Two-dimensional anisotropic random walks with anisotropic density conditions á la Heyde (J Stat Phys 27:721-730, 1982, Stochastic processes, Springer, New York, 1993) yield fixed column configurations and nearest-neighbour random walks in a random environment on the square lattice of the plane as in den Hollander (J Stat Phys 75:891-918, 1994) result in random column configurations. In both cases we conclude simultaneous weak Donsker and strong Strassen type invariance principles in terms of appropriately constructed anisotropic Brownian motions on the plane, with self-contained proofs in both cases. The style of presentation throughout will be that of a semi-expository survey of related results in a historical context.

Two-Dimensional Anisotropic Random Walks: Fixed Versus Random Column Configurations for Transport Phenomena

NASA Astrophysics Data System (ADS)

Csáki, Endre; Csörgő, Miklós; Földes, Antónia; Révész, Pál

2018-06-01

We consider random walks on the square lattice of the plane along the lines of Heyde (J Stat Phys 27:721-730, 1982, Stochastic processes, Springer, New York, 1993) and den Hollander (J Stat Phys 75:891-918, 1994), whose studies have in part been inspired by the so-called transport phenomena of statistical physics. Two-dimensional anisotropic random walks with anisotropic density conditions á la Heyde (J Stat Phys 27:721-730, 1982, Stochastic processes, Springer, New York, 1993) yield fixed column configurations and nearest-neighbour random walks in a random environment on the square lattice of the plane as in den Hollander (J Stat Phys 75:891-918, 1994) result in random column configurations. In both cases we conclude simultaneous weak Donsker and strong Strassen type invariance principles in terms of appropriately constructed anisotropic Brownian motions on the plane, with self-contained proofs in both cases. The style of presentation throughout will be that of a semi-expository survey of related results in a historical context.

Progressive Stereo Locking (PSL): A Residual Dipolar Coupling Based Force Field Method for Determining the Relative Configuration of Natural Products and Other Small Molecules.

PubMed

Cornilescu, Gabriel; Ramos Alvarenga, René F; Wyche, Thomas P; Bugni, Tim S; Gil, Roberto R; Cornilescu, Claudia C; Westler, William M; Markley, John L; Schwieters, Charles D

2017-08-18

Establishing the relative configuration of a bioactive natural product represents the most challenging part in determining its structure. Residual dipolar couplings (RDCs) are sensitive probes of the relative spatial orientation of internuclear vectors. We adapted a force field structure calculation methodology to allow free sampling of both R and S configurations of the stereocenters of interest. The algorithm uses a floating alignment tensor in a simulated annealing protocol to identify the conformations and configurations that best fit experimental RDC and distance restraints (from NOE and J-coupling data). A unique configuration (for rigid molecules) or a very small number of configurations (for less rigid molecules) of the structural models having the lowest chiral angle energies and reasonable magnitudes of the alignment tensor are provided as the best predictions of the unknown configuration. For highly flexible molecules, the progressive locking of their stereocenters into their statistically dominant R or S state dramatically reduces the number of possible relative configurations. The result is verified by checking that the same configuration is obtained by initiating the locking from different regions of the molecule. For all molecules tested having known configurations (with conformations ranging from mostly rigid to highly flexible), the method accurately determined the correct configuration.

Atomic alignment effect in the dissociative energy transfer reaction of metal carbonyls (Fe(CO)5, Ni(CO)4) with oriented Ar (3P2, M(J) = 2).

PubMed

Ohoyama, H; Matsuura, Y

2011-10-13

The atomic alignment effect has been studied for the dissociative energy transfer reaction of metal carbonyls (Fe(CO)(5), Ni(CO)(4)) with the oriented Ar ((3)P(2), M(J) = 2). The emission intensity from the excited metal products (Fe*, Ni*) has been measured as a function of the atomic alignment in the collision frame. The selectivity of the atomic orbital alignment of Ar ((3)P(2), M(J) = 2) (rank 2 moment, a(2)) is found to be opposite for the two reaction systems; the Fe(CO)(5) reaction is favorable at the Π configuration (positive a(2)), while the Ni(CO)(4) reaction is favorable at the Σ configuration (negative a(2)). Moreover, a significant spin alignment effect (rank 4 moment, a(4)) is recognized only in the Ni(CO)(4) reaction. The atomic alignment effect turns out to be essentially different between the two reaction systems; the Fe(CO)(5) reaction is controlled by the configuration of the half-filled 3p atomic orbital of Ar ((3)P(2)) in the collision frame (L dependence), whereas the Ni(CO)(4) reaction is controlled by the configuration of the total angular moment J (including spin) of Ar ((3)P(2)) in the collision frame (J dependence). As the origin of J dependence observed only in the Ni(CO)(4) reaction, the correlation (and/or the interference) between two electron exchange processes via the electron rearrangements is proposed.

A Dynamic Eddy Viscosity Model for the Shallow Water Equations Solved by Spectral Element and Discontinuous Galerkin Methods

NASA Astrophysics Data System (ADS)

Marras, Simone; Suckale, Jenny; Giraldo, Francis X.; Constantinescu, Emil

2016-04-01

We present the solution of the viscous shallow water equations where viscosity is built as a residual-based subgrid scale model originally designed for large eddy simulation of compressible [1] and stratified flows [2]. The necessity of viscosity for a shallow water model not only finds motivation from mathematical analysis [3], but is supported by physical reasoning as can be seen by an analysis of the energetics of the solution. We simulated the flow of an idealized wave as it hits a set of obstacles. The kinetic energy spectrum of this flow shows that, although the inviscid Galerkin solutions -by spectral elements and discontinuous Galerkin [4]- preserve numerical stability in spite of the spurious oscillations in the proximity of the wave fronts, the slope of the energy cascade deviates from the theoretically expected values. We show that only a sufficiently small amount of dynamically adaptive viscosity removes the unwanted high-frequency modes while preserving the overall sharpness of the solution. In addition, it yields a physically plausible energy decay. This work is motivated by a larger interest in the application of a shallow water model to the solution of tsunami triggered coastal flows. In particular, coastal flows in regions around the world where coastal parks made of mitigation hills of different sizes and configurations are considered as a means to deviate the power of the incoming wave. References [1] M. Nazarov and J. Hoffman (2013) "Residual-based artificial viscosity for simulation of turbulent compressible flow using adaptive finite element methods" Int. J. Numer. Methods Fluids, 71:339-357 [2] S. Marras, M. Nazarov, F. X. Giraldo (2015) "Stabilized high-order Galerkin methods based on a parameter-free dynamic SGS model for LES" J. Comput. Phys. 301:77-101 [3] J. F. Gerbeau and B. Perthame (2001) "Derivation of the viscous Saint-Venant system for laminar shallow water; numerical validation" Discrete Contin. Dyn. Syst. Ser. B, 1:89?102 [4] F. X. Giraldo and M. Restelli (2010) "High-order semi-implicit time-integrators for a triangular discontinuous Galerkin oceanic shallow water model. Int. J. Numer. Methods Fluids, 63:1077-1102

Theoretical study of the dielectronic recombination process of Li-like Xe51+ ions

NASA Astrophysics Data System (ADS)

Dou, Lijun; Xie, Luyou; Zhang, Denghong; Dong, Chenzhong; Wen, Weiqiang; Huang, Zhongkui; Ma, Xinwen

2017-05-01

The dielectronic recombination of Li-like Xe51+ (2s) ions was studied using the flexible atomic code based on the relativistic configuration interaction method. The resonance energies, radiative and autoionization rates, and resonance strengths were calculated systematically for the doubly excited states (2p1/2nlj)J(n = 18-32) and (2p3/2n'lj)J(n' = 9-27) of Be-like Xe50+ ions. For the higher Rydberg resonance states with n ≥ 33 and n' ≥ 28, the resonance energies and strengths were obtained by extrapolation based on quantum defect theory. The theoretical rate coefficients, covering the center-of-mass energy range 0-505 eV, are in a better agreement with the experimental results measured at the heavy-ion storage ring ESR than the Multi-Configuration Dirac-Fock calculations, especially at the resonance energy range close to the series limits. Contribution to the Topical Issue: "Atomic and Molecular Data and their Applications", edited by Gordon W.F. Drake, Jung-Sik Yoon, Daiji Kato, Grzegorz Karwasz.

A condition for small bootstrap current in three-dimensional toroidal configurations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mikhailov, M. I., E-mail: mikhaylov-mi@nrcki.ru; Nührenberg, J.; Zille, R.

2016-11-15

It is shown that, if the maximum of the magnetic field strength on a magnetic surface in a threedimensional magnetic confinement configuration with stellarator symmetry constitutes a line that is orthogonal to the field lines and crosses the symmetry line, then the bootstrap current density is smaller compared to that in quasi-axisymmetric (qa) [J. Nührenberg et al., in Proc. of Joint Varenna−Lausanne Int. Workshop on Theory of Fusion Plasmas, Varenna, 1994, p. 3] and quasi-helically (qh) symmetric [J. Nührenberg and R. Zille, Phys. Lett. A 129, 113 (1988)] configurations.

How can coastal parks contain the destructive impact of a tsunami? A numerical approach to the understanding of tsunami-triggered waves in the presence of coastal hills

NASA Astrophysics Data System (ADS)

Marras, Simone; Suckale, Jenny; Lunghino, Brent; Giraldo, Francis X.; Constantinescu, Emil

2016-04-01

From the now common idea that vegetated shores may reduce the power of a destructive storm surge, an increasing number of coastal communities around the world are extending this thinking to the design of coastal parks as a way to limit the impact of a tsunami. Tsunamis and storm surges are significantly different in nature and behavior, and it is implausible that vegetation alone could act as a tsunami mitigation tool. A more comprehensive approach relies on the installation of vegetated, scattered mitigation hills in front of the shore to deviate the incoming tsunami wave instead. The analysis of how natural obstacles affect non-linear tsunami waves is still very limited and consists mostly of one-dimensional studies (e.g., [1, 2]). To that end, this work aims to extend the analysis of the interaction of waves of different shapes (solitary wave, N-wave), sizes (amplitude and wave length), and configurations with large obstacles to two-dimensional flows. The following metrics are used for a quantification of the results: 1) tsunami run-up and run-down and 2) a measure of channelization (via the flow kinetic energy and discharge). First, preliminary results show that the configuration of the obstacles is consequential as long as the amplitude of the incoming wave is large enough relative to the obstacles. In second instance, we also observed that the channelization of the flow between two neighboring obstacles may not be greatly affected solely by the distance between obstacles, but must be analyzed in relationship to the initial wave/wave train. This study is based on the numerical solution of the viscous shallow water equations via high order discontinuous finite elements method (DG) using a quadrilateral version of the model described in [3] and with fully implicit time integration [4]. Large and relatively massive hills appear to be a better solution than any offshore concrete walls, which have shown to possibly enhance the tsunami catastrophic power rather than reducing it. Nevertheless, without a thorough understanding of the behavior of non-linear waves when they approach coastal configurations such as hills, coastal parks may still be far from a safe reality. References [1] P. Lynett (2007) "Effect of shallow water obstruction on long wave run-up and overland flow velocity" J. Waterway, Port, Coastal, Ocean Engrg. 136:455-462 [2] G. F. Carrier, T. T. Wu, H. Yeh (2003) "Tsunami run-up and draw-down on a plane beach" J. Fluid Mech. 475:79-99. [3] F. X. Giraldo and M. Restelli (2010) "High-order semi- implicit time-integrators for a triangular discontinuous Galerkin oceanic shallow water model" Int. J. Numer. Methods Fluids, 63:1077-1102. [4] F X. Giraldo, J F.. Kelly, and E. Constantinescu. "Implicit-explicit formulations of a three-dimensional Nonhydrostatic Unified Model of the Atmosphere (NUMA)" SIAM J. Sci. Comput., 35:1162-1194, 2013.

RSRM Nozzle-to-Case Joint J-leg Development

NASA Technical Reports Server (NTRS)

Albrechtsen, Kevin U.; Eddy, Norman F.; Ewing, Mark E.; McGuire, John R.

2003-01-01

Since the beginning of the Space Shuttle Reusable Solid Rocket Motor (RSRM) program, nozzle-to-case joint polysulfide adhesive gas paths have occurred on several flight motors. These gas paths have allowed hot motor gases to reach the wiper O-ring. Even though these motors continue to fly safely with this condition, a desire was to reduce such occurrences. The RSRM currently uses a J-leg joint configuration on case field joints and igniter inner and outer joints. The J-leg joint configuration has been successfully demonstrated on numerous RSRM flight and static test motors, eliminating hot gas intrusion to the critical O-ring seals on these joints. Using the proven technology demonstrated on the case field joints and igniter joints, a nozzle-to-case joint J-leg design was developed for implementation on RSRM flight motors. This configuration provides an interference fit with nozzle fixed housing phenolics at assembly, with a series of pressurization gaps incorporated outboard of the joint mating surface to aid in joint pressurization and to eliminate any circumferential flow in this region. The joint insulation is bonded to the nozzle phenolics using the same pressure sensitive adhesive used in the case field joints and igniter joints. An enhancement to the nozzle-to-case joint J-leg configuration is the implementation of a carbon rope thermal barrier. The thermal barrier is located downstream of the joint bondline and is positioned within the joint in a manner where any hot gas intrusion into the joint passes through the thermal barrier, reducing gas temperatures to a level that would not affect O-rings downstream of the thermal barrier. This paper discusses the processes used in reaching a final nozzle-to-case joint J-leg design, provides structural and thermal results in support of the design, and identifies fabrication techniques and demonstrations used in arriving at the final configuration.

The ground states of iron(III) porphines: role of entropy-enthalpy compensation, Fermi correlation, dispersion, and zero-point energies.

PubMed

Kepp, Kasper P

2011-10-01

Porphyrins are much studied due to their biochemical relevance and many applications. The density functional TPSSh has previously accurately described the energy of close-lying electronic states of transition metal systems such as porphyrins. However, a recent study questioned this conclusion based on calculations of five iron(III) porphines. Here, we compute the geometries of 80 different electronic configurations and the free energies of the most stable configurations with the functionals TPSSh, TPSS, and B3LYP. Zero-point energies and entropy favor high-spin by ~4kJ/mol and 0-10kJ/mol, respectively. When these effects are included, and all electronic configurations are evaluated, TPSSh correctly predicts the spin of all the four difficult phenylporphine cases and is within the lower bound of uncertainty of any known theoretical method for the fifth, iron(III) chloroporphine. Dispersion computed with DFT-D3 favors low-spin by 3-53kJ/mol (TPSSh) or 4-15kJ/mol (B3LYP) due to the attractive r(-6) term and the shorter distances in low-spin. The very large and diverse corrections from TPSS and TPSSh seem less consistent with the similarity of the systems than when calculated from B3LYP. If the functional-specific corrections are used, B3LYP and TPSSh are of equal accuracy, and TPSS is much worse, whereas if the physically reasonable B3LYP-computed dispersion effect is used for all functionals, TPSSh is accurate for all systems. B3LYP is significantly more accurate when dispersion is added, confirming previous results. Copyright © 2011 Elsevier Inc. All rights reserved.

Automated Tetrahedral Mesh Generation for CFD Analysis of Aircraft in Conceptual Design

NASA Technical Reports Server (NTRS)

Ordaz, Irian; Li, Wu; Campbell, Richard L.

2014-01-01

The paper introduces an automation process of generating a tetrahedral mesh for computational fluid dynamics (CFD) analysis of aircraft configurations in early conceptual design. The method was developed for CFD-based sonic boom analysis of supersonic configurations, but can be applied to aerodynamic analysis of aircraft configurations in any flight regime.

Adaptive Topological Configuration of an Integrated Circuit/Packet-Switched Computer Network.

DTIC Science & Technology

1984-01-01

Gitman et al. [45] state that there are basically two approaches to the integrated network design problem: (1) solve the link/capacity problem for...1972), 1385-1397. 33. Frank, H., and Gitman , I. Economic analysis of integrated voice and data networks: a case study. Proc. of IEEE 66 , 11 (Nov. 1978...1974), 1074-1079. 45. Gitman , I., Hsieh, W., and Occhiogrosso, B. J. Analysis and design of hybrid switching networks. IEEE Trans. on Comm. Com-29

In-beam γ -ray spectroscopy studies of medium-spin states in the odd-odd nucleus 186Re

NASA Astrophysics Data System (ADS)

Matters, D. A.; Kondev, F. G.; Aoi, N.; Ayyad, Y.; Byrne, A. P.; Carpenter, M. P.; Carroll, J. J.; Chiara, C. J.; Davidson, P. M.; Dracoulis, G. D.; Fang, Y. D.; Hoffman, C. R.; Hughes, R. O.; Ideguchi, E.; Janssens, R. V. F.; Kanaya, S.; Kay, B. P.; Kibédi, T.; Lane, G. J.; Lauritsen, T.; McClory, J. W.; Nieminen, P.; Noji, S.; Odahara, A.; Ong, H. J.; Stuchbery, A. E.; Tran, D. T.; Watanabe, H.; Wilson, A. N.; Yamamoto, Y.; Zhu, S.

2017-07-01

Excited states in 186Re with spins up to J =12 ℏ were investigated in two separate experiments using 186W(d ,2 n ) reactions at beam energies of 12.5 and 14.5 MeV. Two- and threefold γ -ray coincidence data were collected using the CAESAR and CAGRA spectrometers, respectively, each composed of Compton-suppressed high-purity germanium detectors. Analysis of the data revealed rotational bands built on several two-quasiparticle intrinsic states, including a long-lived Kπ=(8+) isomer. Configuration assignments were supported by an analysis of in-band properties, such as |gK-gR| values. The excitation energies of the observed intrinsic states were compared with results from multi-quasiparticle blocking calculations, based on the Lipkin-Nogami pairing approach, that included contributions from the residual proton-neutron interactions.

100J-level nanosecond pulsed Yb:YAG cryo-cooled DPSSL amplifier

NASA Astrophysics Data System (ADS)

Smith, J. M.; Butcher, T. J.; Mason, P. D.; Ertel, K.; Phillips, P. J.; Banerjee, S.; De Vido, M.; Chekhlov, O.; Divoky, M.; Pilar, J.; Shaikh, W.; Hooker, C.; Lucianetti, A.; Hernandez Gomez, C.; Mocek, T.; Edwards, C.; Collier, J. L.

2018-02-01

We report on the successful demonstration of the world's first kW average power, 100 Joule-class, high-energy, nanosecond pulsed diode-pumped solid-state laser (DPSSL), DiPOLE100. Results from the first long-term test for amplification will be presented; the system was operated for 1 hour with 10 ns duration pulses at 10 Hz pulse repetition rate and an average output energy of 105 J and RMS energy stability of approximately 1%. The laser system is based on scalable cryogenic gas-cooled multi-slab ceramic Yb:YAG amplifier technology. The DiPOLE100 system comprises three major sub-systems, a spatially and temporally shaped front end, a 10 J cryo-amplifier and a 100 J cryo-amplifier. The 10 J cryo-amplifier contain four Yb:YAG ceramic gain media slabs, which are diode pumped from both sides, while a multi-pass architecture configured for seven passes enables 10 J of energy to be extracted at 10 Hz. This seeds the 100 J cryo-amplifier, which contains six Yb:YAG ceramic gain media slabs with the multi-pass configured for four passes. Our future development plans for this architecture will be introduced including closed-loop pulse shaping, increased energy, higher repetition rates and picosecond operation. This laser architecture unlocks the potential for practical applications including new sources for industrial materials processing and high intensity laser matter studies as envisioned for ELI [1], HiLASE [2], and the European XFEL [3]. Alternatively, it can be used as a pump source for higher repetition rate PW-class amplifiers, which can themselves generate high-brightness secondary radiation and ion sources leading to new remote imaging and medical applications.

Feasibility of Optical Instruments Based on Multiaperture Optics.

DTIC Science & Technology

1984-10-16

system may be configured. The optical elements may be nonimaging concentrators (light horns), the field of view (FOV) of which may be controlled by a...RD-RI58 868 FEASIBILITY OF OPTICAL INSTRUMENTS BASED ON i/I MULTIAPERTURE OPTICS (U) FLORIDA UNIV GAINESVILLE DEPT OF NUCLEAR ENGINEERING SCIENCES J D...d Subtitle) 5. TYPE OF REPORT & PERIOD COVERED ’ 0 Feasibility of Optical Instruments Based on Final Report * CD Multiaperature Optics 615/83 to 9/30

Photometric study of two eclipsing binary stars: Light curve analysis and system parameters for GU CMa and SWASP J011732.10+525204.9

NASA Astrophysics Data System (ADS)

Shokry, A.; Saad, S. M.; Hamdy, M. A.; Beheary, M. M.; Abolazm, M. S.; Gadallah, K. A.; El-Depsey, M. H.; Al-Gazzar, M. S.

2018-02-01

A new photometric study of two eclipsing binary systems (GU CMa and SWASP J011732.10+525204.9) is presented. The accepted solutions of analyzing the light curves revealed that GU CMa is a semi-detached system consisting of two early spectral type components, (B2 and B2.5) while SWASP J011732.10+525204.9 is a contact binary with two late type components (K2 and M1). The primary component of each system is the massive one. The geometric configuration indicates that SWASP J011732.10+525204.9 passes through a very critical phase in which each component exactly fills its limited lobe with zero fill out ratio. New times of minimum and the absolute physical parameters for each system are determined. The evolution status for each system has been investigated.

Viscous Rayleigh-Taylor instability in spherical geometry

NASA Astrophysics Data System (ADS)

Mikaelian, Karnig O.

2016-02-01

We consider viscous fluids in spherical geometry, a lighter fluid supporting a heavier one. Chandrasekhar [Q. J. Mech. Appl. Math. 8, 1 (1955), 10.1093/qjmam/8.1.1] analyzed this unstable configuration providing the equations needed to find, numerically, the exact growth rates for the ensuing Rayleigh-Taylor instability. He also derived an analytic but approximate solution. We point out a weakness in his approximate dispersion relation (DR) and offer a somewhat improved one. A third DR, based on transforming a planar DR into a spherical one, suffers no unphysical predictions and compares reasonably well with the exact work of Chandrasekhar and a more recent numerical analysis of the problem [Terrones and Carrara, Phys. Fluids 27, 054105 (2015), 10.1063/1.4921648].

International Space Station Configuration Analysis and Integration

NASA Technical Reports Server (NTRS)

Anchondo, Rebekah

2016-01-01

Ambitious engineering projects, such as NASA's International Space Station (ISS), require dependable modeling, analysis, visualization, and robotics to ensure that complex mission strategies are carried out cost effectively, sustainably, and safely. Learn how Booz Allen Hamilton's Modeling, Analysis, Visualization, and Robotics Integration Center (MAVRIC) team performs engineering analysis of the ISS Configuration based primarily on the use of 3D CAD models. To support mission planning and execution, the team tracks the configuration of ISS and maintains configuration requirements to ensure operational goals are met. The MAVRIC team performs multi-disciplinary integration and trade studies to ensure future configurations meet stakeholder needs.

Generation of ion temperature anisotropy in kinetic hybrid-Vlasov simulations (Invited)

NASA Astrophysics Data System (ADS)

Perrone, D.; Valentini, F.; Servidio, S.; Dalena, S.; Veltri, P.

2013-12-01

The interplanetary medium is a multi-component and weakly collisional system generally observed to be in a fully turbulent regime [1,2]. The system dynamics at short spatial scales appears to be dominated by kinetic effects that drive the interstellar gas far from the configuration of thermodynamic equilibrium [3-5]. We present a numerical analysis of a turbulent plasma composed of kinetic ions (protons and alpha particles) and fluid electrons in the typical conditions of the solar-wind environment, developed by using a low-noise hybrid Vlasov-Maxwell code [6,7] in a five dimensional phase space configuration (two dimensions in physical space and three dimensions in velocity space) [8]. The ion dynamics at short spatial scales (shorter than the proton skin depth) display several interesting aspects, mainly consisting in the departure of the distribution functions from the typical Maxwellian configuration, which has been systematically quantified through the evalutation of the temperature anisotropy ratio (perpendicular to parallel temperature ratio) with respect to the local magnetic field. This temperature anisotropy appears to be a direct effect of the turbulent nature of the system dynamics. Moreover, the turbulent activity leads to the generation of coherent structures, such as vortices and current sheets. Conditioned ion temperature distributions suggest heating associated with coherent structures; the distribution of ion temperatures moves towards higher values with increasing PVI threshold for the upper inertial range in the turbulent spectra. This behavior is more evident for alpha particles than for protons. The physical phenomenology recovered in these numerical simulations reproduces very common features recovered in 'in situ' measurements in the turbulent solar wind [9-11], suggesting that the multi-ion Vlasov model represents a valid approach to the understanding of the nature of complex kinetic effects in astrophysical plasmas. [1] R. Bruno and V. Carbone, LRSP 2, 4 (2005) [2] E. Marsch, LRSP 3, 1 (2006) [3] E. Marsch, K.-H. Mühlh.user, R. Schwenn, et al., J. Geophys. Res. 87, A1 (1982) [4] E. Marsch, K.-H. Mühlh.user, R. Schwenn, et al., J. Geophys. Res. 35, A1 (1982) [5] J.C. Kasper, A.J. Lazarus and S.P. Gary, Phys. Rev. Lett. 101, 261103 (2008) [6] F. Valentini, P. Trávnícek, F. Califano et al., J. Comput. Phys. 225, 753 (2007) [7] D. Perrone, F. Valentini and P. Veltri, Astrophys. J. 741, 43 (2011) [8] D. Perrone, F. Valentini, S. Servidio et al., Astrophys. J. 762, 99 (2013) [9] B.A. Maruca, J.C. Kasper and S.P. Gary, Astrophys. J. 748, 137 (2012) [10] S. Bourouaine, E. Marsch and F.M. Neubauer, Astron. and Astrophys. 536, A39 (2011) [11] P. Wu, S. Perri, K. Osman, et al., Astrophys. J. Lett. 763, L30 (2013)

Associated production of J/ψ and mesons and the prospects to observe a new hypothetical tetraquark state

NASA Astrophysics Data System (ADS)

Baranov, Sergey

2017-10-01

We propose a new mechanism for prompt simultaneous production of J/ψ and mesons in high energy hadronic collisions. The process is considered as a perturbative production of mesons followed by a long-distance final state interaction that rearranges the quarks to form J/ψ and mesons. Passing from configuration to J/ψ+ configuration may proceed via a hypothetical resonance state, the tetraquark. The goal of this work is to examine whether the respective cross section is large enough to encourage a direct search for the tetraquark at the LHC conditions (yes), and whether this hypothesis can help to explain recent D0 data without assigning an unusually low value to σeff in the double parton scattering mechanism (no).

In-beam γ -ray spectroscopy studies of medium-spin states in the odd-odd nucleus Re 186

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matters, D. A.; Kondev, F. G.; Aoi, N.

2017-07-01

Excited states in 186Re with spins up to J = 12~ were investigated in two separate experiments using 186W(d, 2n) reactions at beam energies of 12.5 MeV and 14.5 MeV. Two- and three-fold γ-ray coincidence data were collected using the CAESAR and CAGRA spectrometers, respectively, each composed of Compton-suppressed HpGe detectors. Analysis of the data revealed rotational bands built on several two-quasiparticle intrinsic states, including a long-lived Kπ = (8+) isomer. Configuration assignments were supported by an analysis of in-band properties, such as |gK - gR| values. The excitation energies of the observed intrinsic states were compared with results frommore » multiquasiparticle blocking calculations, based on the Lipkin-Nogami pairing approach, that included contributions from the residual proton-neutron interactions.« less

Optimal lightpath placement on a metropolitan-area network linked with optical CDMA local nets

NASA Astrophysics Data System (ADS)

Wang, Yih-Fuh; Huang, Jen-Fa

2008-01-01

A flexible optical metropolitan-area network (OMAN) [J.F. Huang, Y.F. Wang, C.Y. Yeh, Optimal configuration of OCDMA-based MAN with multimedia services, in: 23rd Biennial Symposium on Communications, Queen's University, Kingston, Canada, May 29-June 2, 2006, pp. 144-148] structured with OCDMA linkage is proposed to support multimedia services with multi-rate or various qualities of service. To prioritize transmissions in OCDMA, the orthogonal variable spreading factor (OVSF) codes widely used in wireless CDMA are adopted. In addition, for feasible multiplexing, unipolar OCDMA modulation [L. Nguyen, B. Aazhang, J.F. Young, All-optical CDMA with bipolar codes, IEEE Electron. Lett. 31 (6) (1995) 469-470] is used to generate the code selector of multi-rate OMAN, and a flexible fiber-grating-based system is used for the equipment on OCDMA-OVSF code. These enable an OMAN to assign suitable OVSF codes when creating different-rate lightpaths. How to optimally configure a multi-rate OMAN is a challenge because of displaced lightpaths. In this paper, a genetically modified genetic algorithm (GMGA) [L.R. Chen, Flexible fiber Bragg grating encoder/decoder for hybrid wavelength-time optical CDMA, IEEE Photon. Technol. Lett. 13 (11) (2001) 1233-1235] is used to preplan lightpaths in order to optimally configure an OMAN. To evaluate the performance of the GMGA, we compared it with different preplanning optimization algorithms. Simulation results revealed that the GMGA very efficiently solved the problem.

40 CFR 1068.120 - What requirements must I follow to rebuild engines?

Code of Federal Regulations, 2010 CFR

2010-07-01

... recordkeeping requirements in paragraphs (j) and (k) of this section apply only to businesses. For maintenance... in its certified configuration. Identify the model year of the resulting engine configuration. You... later model year. You may also rebuild it to a certified configuration from an earlier model year as...

Spectrum and Morphology of the Two Brightest Milagro Sources in the Cygnus Region: MGRO J2019+37 and MGRO J2031+41

NASA Astrophysics Data System (ADS)

Abdo, A. A.; Abeysekara, U.; Allen, B. T.; Aune, T.; Berley, D.; Bonamente, E.; Christopher, G. E.; DeYoung, T.; Dingus, B. L.; Ellsworth, R. W.; Galbraith-Frew, J. G.; Gonzalez, M. M.; Goodman, J. A.; Hoffman, C. M.; Hüntemeyer, P. H.; Hui, C. M.; Kolterman, B. E.; Linnemann, J. T.; McEnery, J. E.; Mincer, A. I.; Morgan, T.; Nemethy, P.; Pretz, J.; Ryan, J. M.; Saz Parkinson, P. M.; Shoup, A.; Sinnis, G.; Smith, A. J.; Vasileiou, V.; Walker, G. P.; Williams, D. A.; Yodh, G. B.

2012-07-01

The Cygnus region is a very bright and complex portion of the TeV sky, host to unidentified sources and a diffuse excess with respect to conventional cosmic-ray propagation models. Two of the brightest TeV sources, MGRO J2019+37 and MGRO J2031+41, are analyzed using Milagro data with a new technique, and their emission is tested under two different spectral assumptions: a power law and a power law with an exponential cutoff. The new analysis technique is based on an energy estimator that uses the fraction of photomultiplier tubes in the observatory that detect the extensive air shower. The photon spectrum is measured in the range 1-100 TeV using the last three years of Milagro data (2005-2008), with the detector in its final configuration. An F-test indicates that MGRO J2019+37 is better fit by a power law with an exponential cutoff than by a simple power law. The best-fitting parameters for the power law with exponential cutoff model are a normalization at 10 TeV of 7+5 -2 × 10-10 s-1 m-2 TeV-1, a spectral index of 2.0+0.5 -1.0, and a cutoff energy of 29+50 -16 TeV. MGRO J2031+41 shows no evidence of a cutoff. The best-fitting parameters for a power law are a normalization of 2.1+0.6 -0.6 × 10-10 s-1 m-2 TeV-1 and a spectral index of 3.22+0.23 -0.18. The overall flux is subject to a ~30% systematic uncertainty. The systematic uncertainty on the power-law indices is ~0.1. Both uncertainties have been verified with cosmic-ray data. A comparison with previous results from TeV J2032+4130, MGRO J2031+41, and MGRO J2019+37 is also presented.

Comparative analysis of different configurations of PLC-based safety systems from reliability point of view

NASA Technical Reports Server (NTRS)

Tapia, Moiez A.

1993-01-01

The study of a comparative analysis of distinct multiplex and fault-tolerant configurations for a PLC-based safety system from a reliability point of view is presented. It considers simplex, duplex and fault-tolerant triple redundancy configurations. The standby unit in case of a duplex configuration has a failure rate which is k times the failure rate of the standby unit, the value of k varying from 0 to 1. For distinct values of MTTR and MTTF of the main unit, MTBF and availability for these configurations are calculated. The effect of duplexing only the PLC module or only the sensors and the actuators module, on the MTBF of the configuration, is also presented. The results are summarized and merits and demerits of various configurations under distinct environments are discussed.

State-of-the-Art Engineering Aeroprediction Methods with Emphasis on New Semiempirical Techniques for Predicting Nonlinear Aerodynamics on Complete Missile Configurations

DTIC Science & Technology

1993-11-01

ON COMPLETE MISSILE CONFIGURATIONS BY FRANK G. MOORE WEAPONS SYSTEMS DEPARTMENT NOVEMBER 1993 DTIC ,A -LECTE. DEC 1 3 1993 7;] Approved for public...Di t ib , tio Av J,fia ii !y Cc,,jes Approved for public release; distribution is unlimited. Avii j iUr Di"t NAVAL SURFACE WARFARE CENTER DAHLGREN...CONTENTS Setion 1.0 INTRODUCTION AND BACKGROUND .................... 1 - 1 1.1 USES FOR AERODYNAMICS ........................... 1 - 1 1.2 TYPES OF

Iso-thermal flow characteristics of rotationally symmetric jets generating a swirl within a cylindrical chamber

NASA Astrophysics Data System (ADS)

Long, Shen; Lau, Timothy C. W.; Chinnici, Alfonso; Tian, Zhao Feng; Dally, Bassam B.; Nathan, Graham J.

2018-05-01

We present a systematic experimental study of the interaction between four rotationally symmetric jets within a cylindrical chamber, under conditions relevant to a wide range of engineering applications, including the technology of a Hybrid Solar Receiver Combustor (HSRC). The HSRC geometry is simplified here to a cylindrical cavity with four inlet jets (representing four burners) which are configured in an annular arrangement and aligned at an inclination angle to the axis with a tangential component (azimuthal angle) to generate a swirl in the chamber. In this study, the jet inclination angle (αj) was varied over the range of 25°-45°, while the jet azimuthal angle (θj) was varied from 5° to 15°. The inlet Reynolds number for each injected jet and the number of jets were fixed at ReD = 10 500 and 4, respectively. Measurements obtained with Particle Image Velocimetry were used to characterise the large-scale flow field within selected configurations. The results reveal a significant dependence of the mean and root-mean-square flow-fields on the jet azimuthal angle (θj) and the jet inclination angle (αj). Three different flow regimes with distinctive flow characteristics were identified within the configurations investigated here. It was also found that θj can significantly influence (a) the position and strength of an external recirculation zone and a central recirculation zone, (b) the extent of turbulence fluctuation, and (c) the flow unsteadiness. Importantly, the effect of αj on the flow characteristics was found to depend strongly on the value of θj.

Oxylipins from Dracontium loretense.

PubMed

Benavides, Angelyne; Napolitano, Assunta; Bassarello, Carla; Carbone, Virginia; Gazzerro, Patrizia; Malfitano, Annamaria; Saggese, Paola; Bifulco, Maurizio; Piacente, Sonia; Pizza, Cosimo

2009-05-22

Four novel oxylipins (1-4) were isolated from the n-butanol extract of the corms of Dracontium loretense. Their structures were assigned by 1D and 2D NMR analyses and electrospray ionization multistage ion trap mass spectrometry (ESI-ITMS(n)) data. Relative configurations were assigned on the basis of combined analysis of homonuclear and heteronuclear (2,3)J couplings, along with ROE data. Oxylipin 2 exhibited an immunostimulatory effect on human PBMC proliferation.

Machine Learning Based Dimensionality Reduction Facilitates Ligand Diffusion Paths Assessment: A Case of Cytochrome P450cam.

PubMed

Rydzewski, J; Nowak, W

2016-04-12

In this work we propose an application of a nonlinear dimensionality reduction method to represent the high-dimensional configuration space of the ligand-protein dissociation process in a manner facilitating interpretation. Rugged ligand expulsion paths are mapped into 2-dimensional space. The mapping retains the main structural changes occurring during the dissociation. The topological similarity of the reduced paths may be easily studied using the Fréchet distances, and we show that this measure facilitates machine learning classification of the diffusion pathways. Further, low-dimensional configuration space allows for identification of residues active in transport during the ligand diffusion from a protein. The utility of this approach is illustrated by examination of the configuration space of cytochrome P450cam involved in expulsing camphor by means of enhanced all-atom molecular dynamics simulations. The expulsion trajectories are sampled and constructed on-the-fly during molecular dynamics simulations using the recently developed memetic algorithms [ Rydzewski, J.; Nowak, W. J. Chem. Phys. 2015 , 143 ( 12 ), 124101 ]. We show that the memetic algorithms are effective for enforcing the ligand diffusion and cavity exploration in the P450cam-camphor complex. Furthermore, we demonstrate that machine learning techniques are helpful in inspecting ligand diffusion landscapes and provide useful tools to examine structural changes accompanying rare events.

N=151Pu,Cm and Cf nuclei under rotational stress: Role of higher-order deformations

DOE PAGES

Hota, S. S.; Chowdhury, P.; Khoo, T. L.; ...

2014-10-18

The fast-rotating N=151 isotones 245Pu, 247Cm and 249Cf have been studied through inelastic excitation and transfer reactions with radioactive targets. While all have a ground-state band built on a νj 15/2[734]9/2 - Nilsson configuration, new excited bands have also been observed in each isotone. These odd-N excited bands allow a comparison of the alignment behavior for two different configurations, where the νj 15/2 alignment is either blocked or allowed. The effect of higher order deformations is explored through cranking calculations, which help clarify the elusive nature of νj 15/2 alignments.

Efficient Dual Head Nd:YAG 100mJ Oscillator for Remote Sensing

NASA Technical Reports Server (NTRS)

Coyle, Donald B.; Stysley, Paul R.; Kay, Richard b.; Poulios, Demetrios

2007-01-01

A diode pumped, Nd:YAG laser producing 100 mJ Q-switched pulses and employing a dual-pump head scheme in an unstable resonator configuration is described. Each head contains a side pumped zig-zag slab and four 6-bar QCW 808 nm diodes arrays which are de-rated 23%. Denoting 'z' as the lasing axis, the pump directions were along the x-axis in one head and the y-axis in the other, producing a circularized thermal lens, more typical in laser rod-based cavities. The dual head design's effective thermal lens is now corrected with a proper HR mirror curvature selection. This laser has demonstrated over 100 mJ output with high optical efficiency (24%), good TEM(sub 00) beam quality, and high pointing stability.

Evaluation of the AIRIS Standoff Hyperspectral Imaging System

DTIC Science & Technology

2011-01-01

desorption gas chromatography ( TD -GC). 13 4.4 Sensor Configuration For these measurements the AIRIS sensor was mounted on a lab bench opposite the fume...I J. ^4 5 . . ? J? s - » - ? ] g > > 1 ; j ’.’ S •; u] | 1 z | r 2 .• ^ z i ^ ^ ^’ i £ ^ | | i i 2 | Z I i i £ J: • in 1/1 c & <£• •: llJ 15 10

A magnetic resonance imaging-based articulatory and acoustic study of “retroflex” and “bunched” American English ∕r∕

PubMed Central

Zhou, Xinhui; Espy-Wilson, Carol Y.; Boyce, Suzanne; Tiede, Mark; Holland, Christy; Choe, Ann

2008-01-01

Speakers of rhotic dialects of North American English show a range of different tongue configurations for ∕r∕. These variants produce acoustic profiles that are indistinguishable for the first three formants [Delattre, P., and Freeman, D. C., (1968). “A dialect study of American English r’s by x-ray motion picture,” Linguistics 44, 28–69; Westbury, J. R. et al. (1998), “Differences among speakers in lingual articulation for American English ∕r∕,” Speech Commun. 26, 203–206]. It is puzzling why this should be so, given the very different vocal tract configurations involved. In this paper, two subjects whose productions of “retroflex” ∕r∕ and “bunched” ∕r∕ show similar patterns of F1–F3 but very different spacing between F4 and F5 are contrasted. Using finite element analysis and area functions based on magnetic resonance images of the vocal tract for sustained productions, the results of computer vocal tract models are compared to actual speech recordings. In particular, formant-cavity affiliations are explored using formant sensitivity functions and vocal tract simple-tube models. The difference in F4∕F5 patterns between the subjects is confirmed for several additional subjects with retroflex and bunched vocal tract configurations. The results suggest that the F4∕F5 differences between the variants can be largely explained by differences in whether the long cavity behind the palatal constriction acts as a half- or a quarter-wavelength resonator. PMID:18537397

Analysis and sizing of Mars aerobrake structure

NASA Technical Reports Server (NTRS)

Raju, I. S.; Craft, W. J.

1993-01-01

A cone-sphere aeroshell structure for aerobraking into Martian atmosphere is studied. Using this structural configuration, a space frame load-bearing structure is proposed. To generate this structure efficiently and to perform a variety of studies of several configurations, a mesh generator that utilizes only a few configurational parameters is developed. A finite element analysis program that analyzes space frame structures was developed. A sizing algorithm that arrives at a minimum mass configuration was developed and integrated into the finite element analysis program. A typical 135-ft-diam aerobrake configuration was analyzed and sized. The minimum mass obtained in this study using high modulus graphite/epoxy composite material members is compared with the masses obtained from two other aerobrake structures using lightweight erectable tetrahedral truss and part-spherical truss configurations. Excellent agreement for the minimum mass was obtained with the three different aerobrake structures. Also, the minimum mass using the present structure was obtained when the supports were not at the base but at about 75 percent of the base diameter.

Application of hydrodynamic cavitation to improve the biodegradability of mature landfill leachate.

PubMed

Bis, M; Montusiewicz, A; Ozonek, J; Pasieczna-Patkowska, S

2015-09-01

In this study, the application of hydrodynamic cavitation to improve the biodegradability of mature landfill leachate was investigated. Three configurations of cavitation device were examined and operational parameters of the process were selected. The study indicated that the orifice plate with a 3/10mm diameter conical concentric hole, characterized by the cavitation number of 0.033, is a reasonable choice to ensure the enhanced biodegradability of mature leachate. Using such a configuration and maintaining 30 recirculation passes through the cavitation zone at inlet pressure of 7 bar, the highest increase of biodegradability index (BI) of approximately 22% occurred, i.e., from the value of 0.046 to 0.056. The FT-IR/PAS analysis confirmed a degradation of refractory compounds that typically prevail in mature leachate. An evaluation of energy efficiency was made in terms of the actual consumed energy measured by using the Kyoritsu KEW6310 Power Quality Tester. A cavitational yield of 9.8 mg COD kJ(-1) was obtained for the optimum configuration and 30 recirculation passes. Regarding energy efficiency, the application of 10 cavitation cycles appeared to be the most profitable. This was due to an almost threefold higher cavitational yield of 27.5 mg COD kJ(-1). However, the preferable option should be selected by considering a satisfactory effect in the biodegradability enhancement. Copyright © 2015 Elsevier B.V. All rights reserved.

A PBOM configuration and management method based on templates

NASA Astrophysics Data System (ADS)

Guo, Kai; Qiao, Lihong; Qie, Yifan

2018-03-01

The design of Process Bill of Materials (PBOM) holds a hinge position in the process of product development. The requirements of PBOM configuration design and management for complex products are analysed in this paper, which include the reuse technique of configuration procedure and urgent management need of huge quantity of product family PBOM data. Based on the analysis, the function framework of PBOM configuration and management has been established. Configuration templates and modules are defined in the framework to support the customization and the reuse of configuration process. The configuration process of a detection sensor PBOM is shown as an illustration case in the end. The rapid and agile PBOM configuration and management can be achieved utilizing template-based method, which has a vital significance to improve the development efficiency for complex products.

Sidney Blatt's Contributions to Personality Assessment.

PubMed

Auerbach, John S

2016-01-01

Over a long, distinguished career, Sidney Blatt contributed to theory and research in personality development, personality assessment, and psychotherapy. Best known for his 2-configurations model of personality and author or co-author of more than 250 articles and 18 books and monographs, Blatt was also a master clinician, a psychoanalyst who was awarded the 1989 Bruno J. Klopfer Award by the Society for Personality Assessment (SPA) for his contributions to both self-report and performance-based assessment. He was also the president of SPA from 1984 to 1986. This special series contains papers by writers who participated in all aspects of Blatt's contributions to personality assessment, both self-report and performance-based. Topics covered include Blatt's 2-configurations model of personality, development, and psychopathology; boundary disturbance and psychosis in performance-based assessment; the interaction of gender and personality on narrative assessments; and the Object Relations Inventory and differentiation relatedness, especially as these relate to therapeutic outcome.

Biohazard Detoxification Method Utilizing Magnetic Particles

DTIC Science & Technology

2007-05-01

configurations (noted by the yellow in the flow tube region). These data highlight the importance of the magnetic field gradient in particle capture...Weyhers, F. Specht , J.S. Lucks, Int. J. Pharm. 138(1996) 85. [9] Z.L. Liu, Z.H. Ding, K.L. Yao, J. Magn. Magn. Mater. 265(2003) 98. [10] P.A. Dresco

Interfacial electronic structure and full spectral Hamaker constants of Si{sub 3}N{sub 4} intergranular films from VUV and SR-VEEL spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

French, R.H.; Scheu, C.; Duscher, G.

1995-09-01

The interfacial electronic structure, presented as the interband transition strength J{sub cv}({omega}) of the interatomic bonds, can be determined by Kramers Kronig (KK) analysis of vacuum ultraviolet (VUV) reflectance or spatially resolved valence electron energy loss (SR-VEEL) spectra. For the wetted interfaces in Si{sub 3}N{sub 4}, equilibrium thin glass films are formed whose thickness is determined by a force balance between attractive and repulsive force terms KK analysis of J{sub cv}({omega}) to yield {var_epsilon}{sub 2}({xi}) for the phases present, permits the direct calculation of the configuration-dependent Hamaker constants for the attractive vdW forces from the interfacial electronic structure. Interband transitionmore » strengths and full spectral Hamaker constants for Si{sub 3}N{sub 4}samples containing a SiYAlON glass have been determined using SR-VEELS from grains and grain boundaries and compared with results from bulk VUV spectroscopy on separate samples of glass and nitride. The A{sub 121}Hamaker constant for Si{sub 3}N{sub 4} with glass of the bulk composition is 8 zJ (zJ = 10{sup {minus}21}J) from the more established optical method. The EELS method permits the determination of vdW forces based upon actual local compositions and structure, which may differ noticeably from bulk standards. Current results show that full spectral Hamaker constants determined from VUV and SR-VEEL measurements of uniform bulk samples agree, but care must be take in the single scattering and zero loss subtraction corrections, and more work is ongoing in this area. Still the results show that for the grain boundary films present in these polycrystalline Si{sub 3}N{sub 4} samples the glass composition is of lower index of refraction. This can arise from increased oxygen content in determined in situ from the SR-VEELS of a particular grain boundary film. 45 refs.« less

Terrain Analysis Procedural Guide for Surface Configuration.

DTIC Science & Technology

1984-03-01

34’’~ ,w j 0 V~l s A., ; 54 . ’ sC 01.,)f ttt’t 1.f’ &~~ w tS*’tCSA 𔄃’a Ats4 tArot A"- t𔃾 Do’ .’ a’’ SQ t#"N4 psCn9’A’ rhr ta4sto"%t ac’c- 40 " jpV*’ Ae

Composite (La0.45Nd0.25)Sr0.3MnO3/5CuO materials for magnetic refrigeration applications

NASA Astrophysics Data System (ADS)

El Maalam, K.; Balli, M.; Habouti, S.; Dietze, M.; Hamedoun, M.; Hlil, E.-K.; Es-Souni, M.; El Kenz, A.; Benyoussef, A.; Mounkachi, O.

2018-03-01

In this work, the magnetocaloric properties of (La0.45Nd0.25)Sr0.3MnO3 (LNSMO)-based composites are studied. The structural, microstructural, magnetic and magnetocaloric properties of LNSMO and LNSMO/5CuO samples were investigated aiming to particularly clarify the secondary phase (CuO) role in driving the magnetocaloric behavior. The main phase LNSMO crystallizes in a rhombohedral R-3C (1 6 7) configuration. The XRD patterns of composite samples show both perovskite LNSMO and monoclinic Tenorite CuO structures. The microstructural analysis unveils that the CuO phase is mainly present in the grain boundaries and segregates region. On the other hand, it was found that the magnetocaloric effect could be significantly enhanced by adding a small amount of CuO (5% weight ratio). For a magnetic field changing from 0 to 1.5 T, the corresponding isothermal entropy change was found to be 2.55 J/kg K for the LNSMO/5CuO composite while it is only about 1.1 J/kg K for the mother material LNSMO. Our finding should inspire and open new ways for the enhancement of the magnetocaloric effect in manganites-based materials.

A PHOTOMETRIC STUDY OF FOUR RECENTLY DISCOVERED CONTACT BINARIES: 1SWASP J064501.21+342154.9, 1SWASP J155822.10-025604.8, 1SWASP J212808.86+151622.0, AND UCAC4 436-062932

DOE Office of Scientific and Technical Information (OSTI.GOV)

Djurašević, G.; Latković, O.; Cséki, A.

We present new, high-quality multicolor observations of four recently discovered contact binaries, 1SWASP J064501.21+342154.9, 1SWASP J155822.10-025604.8, 1SWASP J212808.86+151622.0, and UCAC4 436-062932, and analyze their light curves to determine orbital and physical parameters using the modeling program of G. Djurašević. In the absence of spectroscopic observations, the effective temperatures of the brighter components are estimated from the color indices, and the mass ratios are determined with the q -search method. The analysis shows that all four systems are W UMa type binaries in shallow contact configurations, consisting of late-type main-sequence primaries and evolved secondaries with active surface regions (dark or bright spots) resultingmore » from magnetic activity or ongoing transfer of thermal energy between the components. We compare the derived orbital and stellar parameters for these four variables with a large sample of previously analyzed W UMa stars and find that our results fit it well.« less

PTP1B inhibitory and cytotoxic C-24 epimers of Δ28-24-hydroxy stigmastane-type steroids from the brown alga Dictyopteris undulata Holmes.

PubMed

Feng, Mei-Tang; Wang, Ting; Liu, Ai-Hong; Li, Jia; Yao, Li-Gong; Wang, Bin; Guo, Yue-Wei; Mao, Shui-Chun

2018-02-01

Ten stigmastane-type steroids bearing unusual Δ 28 -24-hydroxy side chains, dictyopterisins A-J, including three pairs of C-24 epimers, dictyopterisins B/C, F/G, and I/J, were isolated from the brown alga Dictyopteris undulata Holmes, together with two previously reported analogues, (24S)- and (24R)-saringosterol. Their structures were elucidated on the basis of extensive spectroscopic analysis, with their absolute configurations at the stereogenic center C-24 of the side chain being assigned by a direct comparison of 1 H NMR data with those of related known compounds. The absolute configurations of the steroidal nuclei of dictyopterisins A, B, and H were determined using the modified Mosher's method. The mixture of dictyopterisins D and E and dictyopterisin I exhibited promising PTP1B inhibitory activities with IC 50 values of 1.88 and 3.47 μM, respectively, comparable to the positive control oleanolic acid (IC 50 , 2.78 μM). In addition, the mixture of dictyopterisins D and E and dictyopterisins F-J displayed significant cytotoxicities against the human cancer cell lines HL-60 (IC 50 from 1.02 to 2.70 μM) and A-549 (IC 50 from 1.35 to 2.85 μM). Copyright © 2017 Elsevier Ltd. All rights reserved.

ETF magnet design alternatives for the national MHD program

NASA Astrophysics Data System (ADS)

Marston, P. G.; Thome, R. J.; Dawson, A. M.; Bobrov, E. S.; Hatch, A. M.

1981-01-01

Five superconducting magnet designs are evaluated for a 200 MWe test facility requiring a magnet with an on-axis field of 6 T, an inlet bore area of 4 sq m, storing 6 x 10 to the 9th J. The designs include a straightforward rectangular saddle coil set, a 'Cask' configuration based on staves and corner blocks as the main support structure, and an internally cooled, cabled superconductor to minimize the substructure and eliminate the helium vessel. Also, a modular design using six coils with individual helium vessels and an integrated structure produces a simplest configuration which utilizes a natural rectangular interface for packaging the MHD channel and its connections, and results in a lower capital cost.

Desalination using low grade heat sources

NASA Astrophysics Data System (ADS)

Gude, Veera Gnaneswar

A new, low temperature, energy-efficient and sustainable desalination system has been developed in this research. This system operates under near-vacuum conditions created by exploiting natural means of gravity and barometric pressure head. The system can be driven by low grade heat sources such as solar energy or waste heat streams. Both theoretical and experimental studies were conducted under this research to evaluate and demonstrate the feasibility of the proposed process. Theoretical studies included thermodynamic analysis and process modeling to evaluate the performance of the process using the following alternate energy sources for driving the process: solar thermal energy, solar photovoltaic/thermal energy, geothermal energy, and process waste heat emissions. Experimental studies included prototype scale demonstration of the process using grid power as well as solar photovoltaic/thermal sources. Finally, the feasibility of the process in reclaiming potable-quality water from the effluent of the city wastewater treatment plant was studied. The following results have been obtained from theoretical analysis and modeling: (1) The proposed process can produce up to 8 L/d of freshwater for 1 m2 area of solar collector and evaporation chamber respectively with a specific energy requirement of 3122 kJ for 1 kg of freshwater production. (2) Photovoltaic/thermal (PV/T) energy can produce up to 200 L/d of freshwater with a 25 m2 PV/T module which meets the electricity needs of 21 kWh/d of a typical household as well. This configuration requires a specific energy of 3122 kJ for 1 kg of freshwater production. (3) 100 kg/hr of geothermal water at 60°C as heat source can produce up to 60 L/d of freshwater with a specific energy requirement of 3078 kJ for 1 kg of freshwater production. (4) Waste heat released from an air conditioning system rated at 3.25 kW cooling, can produce up to 125 L/d of freshwater. This configuration requires an additional energy of 208 kJ/kg of freshwater along with the waste heat released from the condenser of air-conditioning system. This additional energy requirement is about 60% of the energy required by a multi stage flash distillation process. The experimental studies were conducted in three phases. In the first phase, electric power from grid as energy source was used to demonstrate the feasibility of the proposed process. These tests showed that freshwater production rate of 0.25 kg/hr can be sustained at evaporation temperatures as low as 40°C with specific energy input of 3,370 kJ/kg, at efficiencies ranging from 65 to 70% during the winter. In the second phase, experiments were conducted utilizing direct solar thermal energy and photovoltaic energy as well. Four different combinations of energy sources were studied. The following results were obtained from these experimental studies: (1) Utilizing direct solar energy produced 4.9 L/d of freshwater with an evaporator area of 1 m2 with an average efficiency of 61%. This yield is two times that can be obtained from a flat solar still. The specific energy requirement for this configuration is 4157 kJ for production of 1 kilogram freshwater; (2) Utilizing direct solar energy with aid of a reflector produced 7.5 L/d of freshwater with an average efficiency more than 80%. The specific energy requirement for this configuration is 3118 kJ for production of 1 kilogram freshwater; (3) Utilizing direct solar energy during sunlight hours and photovoltaic energy during non-sunlight hours produced 12 L/d of freshwater with 1 m2 evaporator area and 6 m2 photovoltaic areas respectively. The specific energy requirement for this configuration is 2926 kJ for production of 1 kilogram freshwater. Finally, the feasibility of this process in reclaiming potable-quality water from the effluent of a domestic wastewater treatment plant was studied. The process was able to achieve the following reductions: total dissolved solids from 727 mg/L to 21 mg/L (97%); nitrates from 2.4 mg/L to <0.1 mg/L (> 95%); ammonia from 23.2 mg/L to < 0.5 mg/L (> 97%); and coliform from 77 to <0 mg/L (100%).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michel, D. T.; Maximov, A. V.; Short, R. W.

The fraction of laser energy converted into hot electrons by the two-plasmon-decay instability is found to have different overlapped intensity thresholds for various configurations on the Omega Laser Facility [T. R. Boehly et al., Opt. Commun. 133, 495 (1997); J. H. Kelly et al., J. Phys. IV 133, 75 (2006)]. A factor-of-2 difference in the overlapped intensity threshold is observed between two- and four-beam configurations. The overlapped intensity threshold increases by a factor of 2 between the 4- and 18-beam configurations and by a factor of 3 between the 4- and 60-beam configurations. This is explained by a linear common-wavemore » model where multiple laser beams drive a common electron-plasma wave in a wavevector region that bisects the laser beams (resonant common-wave region in k-space). These experimental results indicate that the hot-electron threshold depends on the hydrodynamic parameters at the quarter-critical density surface, the configuration of the laser beams, and the sum of the intensity of the beams that share the same angle with the common-wave vector.« less

Self-Assembly of Cis-Configured Squaraine Dyes at the TiO2-Dye Interface: Far-Red Active Dyes for Dye-Sensitized Solar Cells.

PubMed

Punitharasu, Vellimalai; Mele Kavungathodi, Munavvar Fairoos; Nithyanandhan, Jayaraj

2018-05-16

To synergize both steric and electronic factors in designing the dyes for dye-sensitized solar cells, a series of cis-configured unsymmetrical squaraine dyes P11-P15 with suitably functionalized alkyl groups and squaric acid units containing the electron-withdrawing groups were synthesized, respectively. These dyes capture the importance of (i) the effect and position of branched alkyl groups, (ii) mono- and di-anchoring groups containing dyes, and (iii) further appending the alkyl groups through the cyanoester vinyl unit on the central squaric acid units of D-A-D-based cis-configured squaraine dyes. All the above factors govern the controlled self-assembly of the dyes on the TiO 2 surface which helps to broaden the absorption profile of the dyes with an increased energy-harvesting process. With respect to the position of the branched alkyl groups, dye P11 with the sp 3 -C and N-alkyl groups away from the TiO 2 surface showed a better device efficiency of 5.98% ( J sc of 14.46 mA cm -2 , V oc of 0.576 V, and ff of 71.8%) than its positional isomer P12 with 3.45% ( J sc of 8.78 mA cm -2 , V oc of 0.554 V, and ff of 70.9%). However, with respect to the dyes containing mono- and di-anchoring groups, P13 with two anchoring units exhibited a superior device performance of 7.58% ( J sc of 17.12 mA cm -2 , V oc of 0.618 V, and ff of 71.7%) in the presence of optically transparent co-adsorbent CDCA (3α,7α-dihydroxy-5β-cholanic acid) than dyes P11 and P12.

Appearance of Saturn’s F ring azimuthal channels for the anti-alignment configuration between the ring and Prometheus

NASA Astrophysics Data System (ADS)

Chavez, Carlos E.

2009-09-01

In this article we explore the aspect of the F ring with respect to the anti-alignment configuration between the ring and Prometheus. We focus our attention on the shape of the F ring's azimuthal channels which were first reported by Porco et al. (Porco, C.C., Baker, E., Barbara, J., Beurle, K., Brahic, A., Burns, J.A., Charnoz, S., Cooper, N., Dawson, D.D., Del Genio, A.D., Denk, T., Dones, L., Dyudina, U., Evans, M.W., Giese, B., Grazier, K., Helfenstein, P., Ingersoll, A.P., Jacobson, R.A., Johnson, T.V., McEwen, A., Murray, C.D., Neukum, G., Owen, W.M., Perry, J., Roatsch, T., Spitale, J., Squyres, S., Thomas, P., Tiscareno, M., Turtle, E., Vasavada, A.R., Veverka, J., Wagner, R., West, R. [2005] Science, 307, 1226-1236) and numerically explored by Murray et al. (Murray, C.D., Chavez, C., Beurle, K., Cooper, N., Evans, M.W., Burns, J.A., Porco, C.C. [2005] Nature 437, 1326-1329) who found excellent agreement between Cassini's ISS reprojected images and their numerical model via a direct comparison. We find that for anti-alignment the channels are wider and go deeper inside the ring material. From our numerical model we find a new feature, an island in the middle of the channel. This island is made up of the particles that have been perturbed the most by Prometheus and only appears when this satellite is close to apoapsis. In addition, plots of the anti-alignment configuration for different orbital stages of Prometheus are obtained and discussed here.

The Research Progress of the J-TEXT Tokamak

NASA Astrophysics Data System (ADS)

Zhuang, Ge; Wang, Zhijiang; Ding, Yonghua; Zhang, Ming; Yang, Zhoujun; Gao, Li; Zhang, Xiaoqing; Hu, Xiwei; Pan, Yuan

2010-11-01

In 2004, the TEXT-U tokamak was disassembled and shipped to China, and later on settle down in Huazhong University of Science and Technology. The machine was renamed as the Joint TEXT (J-TEXT) tokamak and obtained its first plasma in 2007. The typical J-TEXT Ohmic discharge was performed in the limiter configuration with the main parameters as follows: major radius R=1.05 m, minor radius a=0.27m, toroidal magnetic field BT=2.2T, plasma current Ip>200kA, line-averaged density ne˜ 2-3 . 1019/m^3, and electron temperature Te0˜ 700eV. Up till now, a few diagnostic systems used to facilitate routine operation and experimental studies were designed and developed. Benefiting from these diagnostic tools, the observation of MHD activities and the statistical analysis of disruption events were done. And measurements of the electrostatic fluctuations in the edge region and conditional analysis of the intermittent burst events near the LCFS were also made as well. The preliminary results will be presented in detail in the meeting.

A Real-Time Data Acquisition and Processing Framework Based on FlexRIO FPGA and ITER Fast Plant System Controller

NASA Astrophysics Data System (ADS)

Yang, C.; Zheng, W.; Zhang, M.; Yuan, T.; Zhuang, G.; Pan, Y.

2016-06-01

Measurement and control of the plasma in real-time are critical for advanced Tokamak operation. It requires high speed real-time data acquisition and processing. ITER has designed the Fast Plant System Controllers (FPSC) for these purposes. At J-TEXT Tokamak, a real-time data acquisition and processing framework has been designed and implemented using standard ITER FPSC technologies. The main hardware components of this framework are an Industrial Personal Computer (IPC) with a real-time system and FlexRIO devices based on FPGA. With FlexRIO devices, data can be processed by FPGA in real-time before they are passed to the CPU. The software elements are based on a real-time framework which runs under Red Hat Enterprise Linux MRG-R and uses Experimental Physics and Industrial Control System (EPICS) for monitoring and configuring. That makes the framework accord with ITER FPSC standard technology. With this framework, any kind of data acquisition and processing FlexRIO FPGA program can be configured with a FPSC. An application using the framework has been implemented for the polarimeter-interferometer diagnostic system on J-TEXT. The application is able to extract phase-shift information from the intermediate frequency signal produced by the polarimeter-interferometer diagnostic system and calculate plasma density profile in real-time. Different algorithms implementations on the FlexRIO FPGA are compared in the paper.

Machine learning assisted first-principles calculation of multicomponent solid solutions: estimation of interface energy in Ni-based superalloys

NASA Astrophysics Data System (ADS)

Chandran, Mahesh; Lee, S. C.; Shim, Jae-Hyeok

2018-02-01

A disordered configuration of atoms in a multicomponent solid solution presents a computational challenge for first-principles calculations using density functional theory (DFT). The challenge is in identifying the few probable (low energy) configurations from a large configurational space before DFT calculation can be performed. The search for these probable configurations is possible if the configurational energy E({\\boldsymbol{σ }}) can be calculated accurately and rapidly (with a negligibly small computational cost). In this paper, we demonstrate such a possibility by constructing a machine learning (ML) model for E({\\boldsymbol{σ }}) trained with DFT-calculated energies. The feature vector for the ML model is formed by concatenating histograms of pair and triplet (only equilateral triangle) correlation functions, {g}(2)(r) and {g}(3)(r,r,r), respectively. These functions are a quantitative ‘fingerprint’ of the spatial arrangement of atoms, familiar in the field of amorphous materials and liquids. The ML model is used to generate an accurate distribution P(E({\\boldsymbol{σ }})) by rapidly spanning a large number of configurations. The P(E) contains full configurational information of the solid solution and can be selectively sampled to choose a few configurations for targeted DFT calculations. This new framework is employed to estimate (100) interface energy ({σ }{{IE}}) between γ and γ \\prime at 700 °C in Alloy 617, a Ni-based superalloy, with composition reduced to five components. The estimated {σ }{{IE}} ≈ 25.95 mJ m-2 is in good agreement with the value inferred by the precipitation model fit to experimental data. The proposed new ML-based ab initio framework can be applied to calculate the parameters and properties of alloys with any number of components, thus widening the reach of first-principles calculation to realistic compositions of industrially relevant materials and alloys.

A Mixed-Fidelity Approach for Design of Low-Boom Supersonic Aircraft

NASA Technical Reports Server (NTRS)

Li, Wu; Shields, Elwood; Geiselhart, Karl A.

2010-01-01

This paper documents a mixed-fidelity approach for the design of low-boom supersonic aircraft as a viable approach for designing a practical low-boom supersonic configuration. A low-boom configuration that is based on low-fidelity analysis is used as the baseline. Tail lift is included to help tailor the aft portion of the ground signature. A comparison of low- and high-fidelity analysis results demonstrates the necessity of using computational fluid dynamics (CFD) analysis in a low-boom supersonic configuration design process. The fuselage shape is modified iteratively to obtain a configuration with a CFD equivalent-area distribution that matches a predetermined low-boom target distribution. The mixed-fidelity approach can easily refine the low-fidelity low-boom baseline into a low-boom configuration with the use of CFD equivalent-area analysis. The ground signature of the final configuration is calculated by using a state-of-the-art CFD-based boom analysis method that generates accurate midfield pressure distributions for propagation to the ground with ray tracing. The ground signature that is propagated from a midfield pressure distribution has a shaped ramp front, which is similar to the ground signature that is propagated from the CFD equivalent-area distribution. This result confirms the validity of the low-boom supersonic configuration design by matching a low-boom equivalent-area target, which is easier to accomplish than matching a low-boom midfield pressure target.

Mechanical Design of Innovative Electromagnetic Linear Actuators for Marine Applications

NASA Astrophysics Data System (ADS)

Muscia, Roberto

2017-11-01

We describe an engineering solution to manufacture electromagnetic linear actuators for moving rudders and fin stabilizers of military shipsItalian Ministry of Defence, General Direction of Naval Equipments (NAVARM), Projects ISO (2012-2014) and EDDA (2015-2017). . The solution defines the transition from the conceptual design of the device initially studied from an electromagnetic point of view to mechanical configurations that really work. The structural problems that have been resolved with the proposed configuration are described. In order to validate the design choices discussed we illustrate some results of the numerical simulations performed by the structural finite elements method. These results quantitatively justify the suggested mechanical solution by evaluating stresses and deformations in a virtual prototype of the structure during its functioning. The parts of the device that have been studied are the most critical because in cases of excessive deformation/stress, they can irreparably compromise the actuator operation. These parts are the pole piece-base set and the retention cages of the permanent magnets. The FEM analysis has allowed us to identify the most stressed areas of the previous elements whose shape has been appropriately designed so as to reduce the maximum stresses and deformations. Moreover, the FEM analysis helped to find the most convenient solution to join the pole pieces to the respective bases. The good results obtained by the suggested engineering solution have been experimentally confirmed by tests on a small prototype actuator purposely manufactured. Finally, a qualitative analysis of the engineering problems that have to be considered to design electromagnetic linear actuators bigger than the one already manufactured is illustrated.

Calculation of the exchange coupling constants of copper binuclear systems based on spin-flip constricted variational density functional theory.

PubMed

Zhekova, Hristina R; Seth, Michael; Ziegler, Tom

2011-11-14

We have recently developed a methodology for the calculation of exchange coupling constants J in weakly interacting polynuclear metal clusters. The method is based on unrestricted and restricted second order spin-flip constricted variational density functional theory (SF-CV(2)-DFT) and is here applied to eight binuclear copper systems. Comparison of the SF-CV(2)-DFT results with experiment and with results obtained from other DFT and wave function based methods has been made. Restricted SF-CV(2)-DFT with the BH&HLYP functional yields consistently J values in excellent agreement with experiment. The results acquired from this scheme are comparable in quality to those obtained by accurate multi-reference wave function methodologies such as difference dedicated configuration interaction and the complete active space with second-order perturbation theory. © 2011 American Institute of Physics

Aflaquinolones A-G: secondary metabolites from marine and fungicolous isolates of Aspergillus spp.

PubMed

Neff, Scott A; Lee, Sang Un; Asami, Yukihiro; Ahn, Jong Seog; Oh, Hyuncheol; Baltrusaitis, Jonas; Gloer, James B; Wicklow, Donald T

2012-03-23

Seven new compounds (aflaquinolones A-G; 1-7) containing dihydroquinolin-2-one and terpenoid units have been isolated from two different fungal sources. Two of these metabolites (1 and 2) were obtained from a Hawaiian fungicolous isolate of Aspergillus sp. (section Flavipedes; MYC-2048 = NRRL 58570), while the others were obtained from a marine Aspergillus isolate (SF-5044) collected in Korea. The structures of these compounds were determined mainly by analysis of NMR and MS data. Relative and absolute configurations were assigned on the basis of NOESY data and (1)H NMR J-values, comparison of calculated and experimental ECD spectra, and analysis of a Mosher's ester derivative of 2. Several known compounds, including alantrypinone, aspochalasins I and J, methyl 3,4,5-trimethoxy-2((2-((3-pyridinylcarbonyl)amino)benzoyl)amino)benzoate, and trans-dehydrocurvularin were also encountered in the extract of the Hawaiian isolate.

Generation of warm dense matter using an argon based capillary discharge laser

NASA Astrophysics Data System (ADS)

Rossall, A. K.; Tallents, G. J.

2015-06-01

Argon based capillary discharge lasers operating in the extreme ultra violet (EUV) at 46.9 nm with output up to 0.5 mJ energy per pulse and repetition rates up to 10 Hz are capable of focused irradiances of 109-1012 W cm-2 and can be used to generate plasma in the warm dense matter regime by irradiating solid material. To model the interaction between such an EUV laser and solid material, the 2D radiative-hydrodynamic code POLLUX has been modified to include absorption via direct photo-ionisation, a super-configuration model to describe the ionization-dependent electronic configurations and a calculation of plasma refractive indices for ray tracing of the incident EUV laser radiation. A simulation study is presented, demonstrating how capillary discharge lasers of 1200 ps pulse duration can be used to generate warm dense matter at close to solid densities with temperatures of a few eV and energy densities up to 1 × 105 J cm-3. Plasmas produced by EUV laser irradiation are shown to be useful for examining the properties of warm dense matter as, for example, plasma emission is not masked by hotter, less dense plasma emission that occurs with visible/infra-red laser target irradiation.

CMS Configuration Editor: GUI based application for user analysis job

NASA Astrophysics Data System (ADS)

de Cosa, A.

2011-12-01

We present the user interface and the software architecture of the Configuration Editor for the CMS experiment. The analysis workflow is organized in a modular way integrated within the CMS framework that organizes in a flexible way user analysis code. The Python scripting language is adopted to define the job configuration that drives the analysis workflow. It could be a challenging task for users, especially for newcomers, to develop analysis jobs managing the configuration of many required modules. For this reason a graphical tool has been conceived in order to edit and inspect configuration files. A set of common analysis tools defined in the CMS Physics Analysis Toolkit (PAT) can be steered and configured using the Config Editor. A user-defined analysis workflow can be produced starting from a standard configuration file, applying and configuring PAT tools according to the specific user requirements. CMS users can adopt this tool, the Config Editor, to create their analysis visualizing in real time which are the effects of their actions. They can visualize the structure of their configuration, look at the modules included in the workflow, inspect the dependences existing among the modules and check the data flow. They can visualize at which values parameters are set and change them according to what is required by their analysis task. The integration of common tools in the GUI needed to adopt an object-oriented structure in the Python definition of the PAT tools and the definition of a layer of abstraction from which all PAT tools inherit.

Disassemblability modeling technology of configurable product based on disassembly constraint relation weighted design structure matrix(DSM)

NASA Astrophysics Data System (ADS)

Qiu, Lemiao; Liu, Xiaojian; Zhang, Shuyou; Sun, Liangfeng

2014-05-01

The current research of configurable product disassemblability focuses on disassemblability evaluation and disassembly sequence planning. Little work has been done on quantitative analysis of configurable product disassemblability. The disassemblability modeling technology for configurable product based on disassembly constraint relation weighted design structure matrix (DSM) is proposed. Major factors affecting the disassemblability of configurable product are analyzed, and the disassembling degrees between components in configurable product are obtained by calculating disassembly entropies such as joint type, joint quantity, disassembly path, disassembly accessibility and material compatibility. The disassembly constraint relation weighted DSM of configurable product is constructed and configuration modules are formed by matrix decomposition and tearing operations. The disassembly constraint relation in configuration modules is strong coupling, and the disassembly constraint relation between modules is weak coupling, and the disassemblability configuration model is constructed based on configuration module. Finally, taking a hydraulic forging press as an example, the decomposed weak coupling components are used as configuration modules alone, components with a strong coupling are aggregated into configuration modules, and the disassembly sequence of components inside configuration modules is optimized by tearing operation. A disassemblability configuration model of the hydraulic forging press is constructed. By researching the disassemblability modeling technology of product configuration design based on disassembly constraint relation weighted DSM, the disassembly property in maintenance, recycling and reuse of configurable product are optimized.

Transformative Advances in DDDAS with Application to Space Weather Monitoring

DTIC Science & Technology

2015-10-01

subsystems, including power and communications subsystems. In addition, a study of photovoltaic power generation constraints due to spacecraft solar...estimation. Automatica, 23:775–778, 1987. [61] D. Y. Lee, J. W. Cutler, J. Mancewicz, and A. J. Ridley. Maximizing photovoltaic power generation of a space...Maximizing photovoltaic power generation of a space-dart configured satellite. Acta Astronautica, 111:283–299, 2015. A. V. Morozov, A. J. Ridley, D. S

Hypersonic Flight Vehicle and Ramjet Engine. Considerations of Coordination and Configuration,

DTIC Science & Technology

1980-04-01

oxidizing agent tank of the rocket and the initial weight is reduced. Analysis shows that the weight reduced by liquifying oxygen from the air not opnly...6fvaVThL- tE ~ dtid J ~v~Vf / Prick t D~ri, y? 1~ O 9 21 22 Hight lv’b ,~,i~ ~ 1cvV/L R~e~ viol ~s. lht Plug Pf-05ram,, Ae,+rO"O(ih- 1961. ’- *, s

Instrumental resolution of the chopper spectrometer 4SEASONS evaluated by Monte Carlo simulation

NASA Astrophysics Data System (ADS)

Kajimoto, Ryoichi; Sato, Kentaro; Inamura, Yasuhiro; Fujita, Masaki

2018-05-01

We performed simulations of the resolution function of the 4SEASONS spectrometer at J-PARC by using the Monte Carlo simulation package McStas. The simulations showed reasonably good agreement with analytical calculations of energy and momentum resolutions by using a simplified description. We implemented new functionalities in Utsusemi, the standard data analysis tool used in 4SEASONS, to enable visualization of the simulated resolution function and predict its shape for specific experimental configurations.

Note: Observation of a new electronically excited state of cobalt monoxide

NASA Astrophysics Data System (ADS)

Zang, Jianzheng; Zhang, Qun; Qin, Chengbing; Gu, Zhong; Bai, Xilin; Chen, Yang

2012-11-01

The laser-induced fluorescence excitation spectra of jet-cooled CoO molecules have been recorded in the energy region of 21 800—25 000 cm-1. Apart from the seven vibronic bands assigned to the known G4Φ9/2(υ') - X4Δ7/2(υ″ = 0) progression [M. Barnes, D. J. Clouthier, P. G. Hajigeorgiou, G. Huang, C. T. Kingston, A. J. Merer, G. F. Metha, J. R. D. Peers, and S. J. Rixon, J. Mol. Spectrosc. 186, 374 (1997), 10.1006/jmsp.1997.7456], we observed a new band system assignable to the [22.95]4Δ7/2(υ' = 0 - 4) - X4Δ7/2(υ″ = 0) progression. Extensive perturbations among these vibronic bands have been revealed by means of reduced energy plots. The new electronically excited 4Δ state has been determined to be most likely of an electronic configuration (2pπ)3(4sσ)2(3dδ)3(3dπ)3 based on the charge-transferred promotion model.

A generic analysis of energy use and solvent selection for CO2 separation from post-combustion flue gases

USGS Publications Warehouse

Lu, Y.; Chen, S.; Rostam-Abadi, M.

2008-01-01

A thermodynamic calculation was performed to determine the theoretical minimum energy used to separate CO2 from a coal combustion flue gas in a typical adsorption-desorption system. Under ideal conditions, the minimum energy required to separate CO2 from post-combustion flue gas and produce pure CO2 at 1 atmospheric pressure was only about 1183 kJ/kg CO2. This amount could double with the addition of the driving forces of mass and heat transfer and the adverse impacts of absorption heat release on adsorption capacity. Thermodynamic analyses were also performed for the aqueous amine-based absorption process. Two CO2 reaction mechanisms, the carbamate formation reaction with primary/secondary amines and the CO2 hydration reaction with tertiary amines, were included in the absorption reaction. The reaction heat, sensible heat, and stripping heat were all important to the total heat requirement. The heat use of an ideal tertiary amine amounted to 2786 kJ/kg, compared to 3211 kJ/kg for an ideal primary amine. The heat usage of an ideal amine was about 20% lower than that of commercially available amines. Optimizing the absorption process configuration could further reduce energy use. This is an abstract of a paper presented at the 2008 AIChE Spring National Meeting (New Orleans, LA 4/6-10/2008).

ADVANTG Shielding Analysis for Closure Operations in an Open-Mode Repository

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bevill, Aaron M; Radulescu, Georgeta; Scaglione, John M

2013-01-01

en-mode repository concepts could require worker entry into access drifts after placement of fuel casks in order to perform activities related to backfill, plug emplacement, routine maintenance, or performance confirmation. An ideal emplacement-drift shielding configuration would minimize dose to workers while maximizing airflow through the emplacement drifts. This paper presents a preliminary investigation of the feasibility and effectiveness of radiation shielding concepts that could be employed to facilitate worker operations in an open-mode repository. The repository model for this study includes pressurized-water reactor fuel assemblies (60 GWd/MTU burnup, 40 year post-irradiation cooldown) in packages of 32 assemblies. The closest fuelmore » packages are 5 meters from dosimetry voxels in the access drift. The unshielded dose to workers in the access drift is 73.7 rem/hour. Prior work suggests that open-mode repository concepts similar to this one would require 15 m3/s of ventilation airflow. Shielding concepts considered here include partial concrete plugs, labyrinthine shields, and stainless steel photon attenuator grids. Maximum dose to workers in the access drift was estimated for each shielding concept using MCNP5 with variance reduction parameters generated by ADVANTG. Because airflow through the shielding is important for open-mode repositories, a semi-empirical estimate of the head loss due to each shielding configuration was also calculated. Airflow and shielding performance vary widely among the proposed shielding configurations. Although the partial plug configuration had the best airflow performance, it allowed dose rates 1500 greater than the specified target. Labyrinthine shielding concepts yield doses on the order of 1 mrem/hour with configurations that impose 3 to 11 J/kg head loss. Adding 1 cm lead lining to the airflow channels of labyrinthine designs further reduces the worker dose by 65% to 95%. Photon-attenuator concepts may reduce worker dose to as low as 29 mrem/hour with head loss on the order of 1.9 J/kg.« less

Calculation of the vibrational excited states of malonaldehyde and their tunneling splittings with the multi-configuration time-dependent Hartree method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schröder, Markus, E-mail: Markus.Schroeder@pci.uni-heidelberg.de; Meyer, Hans-Dieter, E-mail: Hans-Dieter.Meyer@pci.uni-heidelberg.de

2014-07-21

We report energies and tunneling splittings of vibrational excited states of malonaldehyde which have been obtained using full dimensional quantum mechanical calculations. To this end we employed the multi configuration time-dependent Hartree method. The results have been obtained using a recently published potential energy surface [Y. Wang, B. J. Braams, J. M. Bowman, S. Carter, and D. P. Tew, J. Chem. Phys. 128, 224314 (2008)] which has been brought into a suitable form by a modified version of the n-mode representation which was used with two different arrangements of coordinates. The relevant terms of the expansion have been identified withmore » a Metropolis algorithm and a diffusion Monte-Carlo technique, respectively.« less

Granger causality--statistical analysis under a configural perspective.

PubMed

von Eye, Alexander; Wiedermann, Wolfgang; Mun, Eun-Young

2014-03-01

The concept of Granger causality can be used to examine putative causal relations between two series of scores. Based on regression models, it is asked whether one series can be considered the cause for the second series. In this article, we propose extending the pool of methods available for testing hypotheses that are compatible with Granger causation by adopting a configural perspective. This perspective allows researchers to assume that effects exist for specific categories only or for specific sectors of the data space, but not for other categories or sectors. Configural Frequency Analysis (CFA) is proposed as the method of analysis from a configural perspective. CFA base models are derived for the exploratory analysis of Granger causation. These models are specified so that they parallel the regression models used for variable-oriented analysis of hypotheses of Granger causation. An example from the development of aggression in adolescence is used. The example shows that only one pattern of change in aggressive impulses over time Granger-causes change in physical aggression against peers.

A new method to solve the Nd breakup scattering problem in configuration space

NASA Astrophysics Data System (ADS)

Suslov, Vladimir

2005-11-01

A new computational method for solving the configuration-space Faddeev equations for three nucleon system has been developed. This method is based on the spline-decomposition in the angular variable and a generalization of the Numerov method for the hyperradius. The s-wave calculations of the inelasticity and phase-shift, as well as breakup amplitudes for nd and pd breakup scattering for lab energies 14.1 and 42.0 MeV were performed with the Malfliet -Tjon MT I-III potential. In the case of nd breakup scattering the results are in good agreement with those of the benchmark solution [1],[2]. In the case of pd quartet breakup scattering disagreement for the inelasticities reaches up to 6% as compared with those of the Pisa group [3]. The calculated pd amplitudes fulfill the optical theorem with a good precision. 1. J. L. Friar, B. F. Gibson, G. Berthold, W. Gloeckle, Th. Cornelius, H. Witala, J. Haidenbauer, Y. Koike, G. L. Payne, J. A. Tjon, and W. M. Kloet,: http://link.aip.org/link/?&lcreator=getabs-normal&ldir=FWD&lrel=CITES&fromkey=PRVCAN000069000004044003000001&fromkeyType=CVIPS&fromloc=AIP&toj=PRVCAN&tov=42&top=1838&toloc=APS&tourl=http%3A%2F%2Flink.aps.org%2Fabstract%2FPRC%2Fv42%2FPhys. Rev. C 42, 1838 (1990). 2. Frair J.L, Payne G.L., Gl"ockle W., Hueber D., Witala H.: Phys. Rev. C 51, 2356 (1995) 3. Kievsky A., Viviani M., and Rosati S.: Phys. Rev. C 64, 024002 (2001)

The stress intensity factors for a periodic array of interacting coplanar penny-shaped cracks

PubMed Central

Lekesiz, Huseyin; Katsube, Noriko; Rokhlin, Stanislav I.; Seghi, Robert R.

2013-01-01

The effect of crack interactions on stress intensity factors is examined for a periodic array of coplanar penny-shaped cracks. Kachanov’s approximate method for crack interactions (Int. J. Solid. Struct. 1987; 23(1):23–43) is employed to analyze both hexagonal and square crack configurations. In approximating crack interactions, the solution converges when the total truncation number of the cracks is 109. As expected, due to high density packing crack interaction in the hexagonal configuration is stronger than that in the square configuration. Based on the numerical results, convenient fitting equations for quick evaluation of the mode I stress intensity factors are obtained as a function of crack density and angle around the crack edge for both crack configurations. Numerical results for the mode II and III stress intensity factors are presented in the form of contour lines for the case of Poisson’s ratio ν =0.3. Possible errors for these problems due to Kachanov’s approximate method are estimated. Good agreement is observed with the limited number of results available in the literature and obtained by different methods. PMID:27175035

SPECTRUM AND MORPHOLOGY OF THE TWO BRIGHTEST MILAGRO SOURCES IN THE CYGNUS REGION: MGRO J2019+37 AND MGRO J2031+41

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdo, A. A.; Abeysekara, U.; Linnemann, J. T.

2012-07-10

The Cygnus region is a very bright and complex portion of the TeV sky, host to unidentified sources and a diffuse excess with respect to conventional cosmic-ray propagation models. Two of the brightest TeV sources, MGRO J2019+37 and MGRO J2031+41, are analyzed using Milagro data with a new technique, and their emission is tested under two different spectral assumptions: a power law and a power law with an exponential cutoff. The new analysis technique is based on an energy estimator that uses the fraction of photomultiplier tubes in the observatory that detect the extensive air shower. The photon spectrum ismore » measured in the range 1-100 TeV using the last three years of Milagro data (2005-2008), with the detector in its final configuration. An F-test indicates that MGRO J2019+37 is better fit by a power law with an exponential cutoff than by a simple power law. The best-fitting parameters for the power law with exponential cutoff model are a normalization at 10 TeV of 7{sup +5}{sub -2} Multiplication-Sign 10{sup -10} s{sup -1} m{sup -2} TeV{sup -1}, a spectral index of 2.0{sup +0.5}{sub -1.0}, and a cutoff energy of 29{sup +50}{sub -16} TeV. MGRO J2031+41 shows no evidence of a cutoff. The best-fitting parameters for a power law are a normalization of 2.1{sup +0.6}{sub -0.6} Multiplication-Sign 10{sup -10} s{sup -1} m{sup -2} TeV{sup -1} and a spectral index of 3.22{sup +0.23}{sub -0.18}. The overall flux is subject to a {approx}30% systematic uncertainty. The systematic uncertainty on the power-law indices is {approx}0.1. Both uncertainties have been verified with cosmic-ray data. A comparison with previous results from TeV J2032+4130, MGRO J2031+41, and MGRO J2019+37 is also presented.« less

Spectrum and Morphology of the Two Brightest Milagro Sources in the Cygnus Region: MGRO J2019+37 and MGRO J2031+41

NASA Technical Reports Server (NTRS)

Abdo, A. A.; Abeysekara, U.; Allen, B, T.; Aune, T.; Berley, D.; Bonamente, E.; Christopher, G. E.; DeYoung, T.; Dingus, B. L.; Ellsworth, R. W.;

Application of computational aeroacoustic methodologies to advanced propeller configurations - A review

NASA Technical Reports Server (NTRS)

Korkan, Kenneth D.; Eagleson, Lisa A.; Griffiths, Robert C.

1991-01-01

Current research in the area of advanced propeller configurations for performance and acoustics are briefly reviewed. Particular attention is given to the techniques of Lock and Theodorsen modified for use in the design of counterrotating propeller configurations; a numerical method known as SSTAGE, which is a Euler solver for the unducted fan concept; the NASPROP-E numerical analysis also based on a Euler solver and used to study the near acoustic fields for the SR series propfan configurations; and a counterrotating propeller test rig designed to obtain an experimental performance/acoustic data base for various propeller configurations.

Full Configuration Interaction Quantum Monte Carlo and Diffusion Monte Carlo: A Comparative Study of the 3D Homogeneous Electron Gas

NASA Astrophysics Data System (ADS)

Shepherd, James J.; López Ríos, Pablo; Needs, Richard J.; Drummond, Neil D.; Mohr, Jennifer A.-F.; Booth, George H.; Grüneis, Andreas; Kresse, Georg; Alavi, Ali

2013-03-01

Full configuration interaction quantum Monte Carlo1 (FCIQMC) and its initiator adaptation2 allow for exact solutions to the Schrödinger equation to be obtained within a finite-basis wavefunction ansatz. In this talk, we explore an application of FCIQMC to the homogeneous electron gas (HEG). In particular we use these exact finite-basis energies to compare with approximate quantum chemical calculations from the VASP code3. After removing the basis set incompleteness error by extrapolation4,5, we compare our energies with state-of-the-art diffusion Monte Carlo calculations from the CASINO package6. Using a combined approach of the two quantum Monte Carlo methods, we present the highest-accuracy thermodynamic (infinite-particle) limit energies for the HEG achieved to date. 1 G. H. Booth, A. Thom, and A. Alavi, J. Chem. Phys. 131, 054106 (2009). 2 D. Cleland, G. H. Booth, and A. Alavi, J. Chem. Phys. 132, 041103 (2010). 3 www.vasp.at (2012). 4 J. J. Shepherd, A. Grüneis, G. H. Booth, G. Kresse, and A. Alavi, Phys. Rev. B. 86, 035111 (2012). 5 J. J. Shepherd, G. H. Booth, and A. Alavi, J. Chem. Phys. 136, 244101 (2012). 6 R. Needs, M. Towler, N. Drummond, and P. L. Ríos, J. Phys.: Condensed Matter 22, 023201 (2010).

Attentional, Associative, and Configural Mechanisms in Extinction

ERIC Educational Resources Information Center

Larrauri, Jose A.; Schmajuk, Nestor A.

2008-01-01

The participation of attentional and associative mechanisms in extinction, spontaneous recovery, external disinhibition, renewal, reinstatement, and reacquisition was evaluated through computer simulations with an extant computational model of classical conditioning (N. A. Schmajuk, Y. Lam, & J. A. Gray, 1996; N. A. Schmajuk & J. A. Larrauri,…

Analyses of Longitudinal Mode Combustion Instability in J-2X Gas Generator Development

NASA Technical Reports Server (NTRS)

Hulka, J. R.; Protz, C. S.; Casiano, M. J.; Kenny, R. J.

2011-01-01

The National Aeronautics and Space Administration (NASA) and Pratt & Whitney Rocketdyne are developing a liquid oxygen/liquid hydrogen rocket engine for future upper stage and trans-lunar applications. This engine, designated the J-2X, is a higher pressure, higher thrust variant of the Apollo-era J-2 engine. The contract for development was let to Pratt & Whitney Rocketdyne in 2006. Over the past several years, development of the gas generator for the J-2X engine has progressed through a variety of workhorse injector, chamber, and feed system configurations on the component test stand at the NASA Marshall Space Flight Center (MSFC). Several of the initial configurations resulted in combustion instability of the workhorse gas generator assembly at a frequency near the first longitudinal mode of the combustion chamber. In this paper, several aspects of these combustion instabilities are discussed, including injector, combustion chamber, feed system, and nozzle influences. To ensure elimination of the instabilities at the engine level, and to understand the stability margin, the gas generator system has been modeled at the NASA MSFC with two techniques, the Rocket Combustor Interaction Design and Analysis (ROCCID) code and a lumped-parameter MATLAB(TradeMark) model created as an alternative calculation to the ROCCID methodology. To correctly predict the instability characteristics of all the chamber and injector geometries and test conditions as a whole, several inputs to the submodels in ROCCID and the MATLAB(TradeMark) model were modified. Extensive sensitivity calculations were conducted to determine how to model and anchor a lumped-parameter injector response, and finite-element and acoustic analyses were conducted on several complicated combustion chamber geometries to determine how to model and anchor the chamber response. These modifications and their ramification for future stability analyses of this type are discussed.

Combustion Stability Analyses for J-2X Gas Generator Development

NASA Technical Reports Server (NTRS)

Hulka, J. R.; Protz, C. S.; Casiano, M. J.; Kenny, R. J.

2010-01-01

The National Aeronautics and Space Administration (NASA) is developing a liquid oxygen/liquid hydrogen rocket engine for upper stage and trans-lunar applications of the Ares vehicles for the Constellation program. This engine, designated the J-2X, is a higher pressure, higher thrust variant of the Apollo-era J-2 engine. Development was contracted to Pratt & Whitney Rocketdyne in 2006. Over the past several years, development of the gas generator for the J-2X engine has progressed through a variety of workhorse injector, chamber, and feed system configurations. Several of these configurations have resulted in injection-coupled combustion instability of the gas generator assembly at the first longitudinal mode of the combustion chamber. In this paper, the longitudinal mode combustion instabilities observed on the workhorse test stand are discussed in detail. Aspects of this combustion instability have been modeled at the NASA Marshall Space Flight Center with several codes, including the Rocket Combustor Interaction Design and Analysis (ROCCID) code and a new lumped-parameter MatLab model. To accurately predict the instability characteristics of all the chamber and injector geometries and test conditions, several features of the submodels in the ROCCID suite of calculations required modification. Finite-element analyses were conducted of several complicated combustion chamber geometries to determine how to model and anchor the chamber response in ROCCID. A large suite of sensitivity calculations were conducted to determine how to model and anchor the injector response in ROCCID. These modifications and their ramification for future stability analyses of this type are discussed in detail. The lumped-parameter MatLab model of the gas generator assembly was created as an alternative calculation to the ROCCID methodology. This paper also describes this model and the stability calculations.

Particle Diffusion in Chaotic Magnetic Fields Generated by Asymmetric Current Configurations

NASA Astrophysics Data System (ADS)

Ram, A. K.; Dasgupta, B.

2008-12-01

The observed cross-field diffusion of charged particles in cosmic rays is assumed to be due to the chaotic nature of the interplanetary/intergalactic magnetic fields. Among the classic works on this subject have been those of Parker [1] and Jokipii [2]. Parker considered the passage of cosmic ray particles and energetic solar particles in a large scale magnetic field containing small scale irregularities. In the context of cosmic ray propagation, Jokipii considered a small fluctuating component, added on to a uniform magnetic field, to study the spatial transport of particles. In these studies the irregular component of the magnetic field is prescribed in an ad hoc fashion. In contrast, we consider asymmetric, nonlinear, steady-state magnetic fields, in three spatial dimensions, generated by currents flowing in circular loops and straight lines [3]. These magnetic fields are completely deterministic and, for certain range of parameters, chaotic. We will present analytical and numerical studies on the spatial characteristics of these fields. The motion of charged particles in the nonlinear and chaotic magnetic fields is determined using the Lorentz equation. A particle moving in a deterministic chaotic magnetic field superposed on a uniform background magnetic field is found to undergo spatial transport. This shows that chaotic magnetic fields generated by simple current configurations can produce cross-field diffusion. A detailed analysis of particle motion and diffusion along with application to space plasmas will be presented. [1] E.N. Parker, Planet. Space Sci. 13, 9 (1965). [2] J.R. Jokipii, Astrophys. J. 146, 480 (1966), and J.R. Jokipii, Astrophys. J. 149, 405 (1967). [3] A.K. Ram and B. Dasgupta, Eos Trans. AGU 87 (52), Fall Meet. Suppl. Abstract NG31B-1593 (2006); and Eos Trans. AGU 88 (52), Fall Meet. Suppl. Abstract NG21B-0522 (2007).

Using Configural Frequency Analysis as a Person-Centered Analytic Approach with Categorical Data

ERIC Educational Resources Information Center

Stemmler, Mark; Heine, Jörg-Henrik

2017-01-01

Configural frequency analysis and log-linear modeling are presented as person-centered analytic approaches for the analysis of categorical or categorized data in multi-way contingency tables. Person-centered developmental psychology, based on the holistic interactionistic perspective of the Stockholm working group around David Magnusson and Lars…

Software Description for the O’Hare Runway Configuration Management System. Volume II. Low-Level Pseudocode,

DTIC Science & Technology

1982-10-01

BACK_ GVRATON; (geserate log me"ses from wather and wind planning log screenJ PERFORN AIPORT.PLANNIG LOGISSA ORItATION; (eSamrate log message from...ISSAGN H31.TAL(COUNT) .26 -kAUX imesase is constructed with wather imforimetiom ad stated) IF(VILO.TAM(J).DIl A(S)’ ’)1 (VXLOG.TABL(J).VU.(S)’ THEN

Unified viscoelasticity: Applying discrete element models to soft tissues with two characteristic times.

PubMed

Anssari-Benam, Afshin; Bucchi, Andrea; Bader, Dan L

2015-09-18

Discrete element models have often been the primary tool in investigating and characterising the viscoelastic behaviour of soft tissues. However, studies have employed varied configurations of these models, based on the choice of the number of elements and the utilised formation, for different subject tissues. This approach has yielded a diverse array of viscoelastic models in the literature, each seemingly resulting in different descriptions of viscoelastic constitutive behaviour and/or stress-relaxation and creep functions. Moreover, most studies do not apply a single discrete element model to characterise both stress-relaxation and creep behaviours of tissues. The underlying assumption for this disparity is the implicit perception that the viscoelasticity of soft tissues cannot be described by a universal behaviour or law, resulting in the lack of a unified approach in the literature based on discrete element representations. This paper derives the constitutive equation for different viscoelastic models applicable to soft tissues with two characteristic times. It demonstrates that all possible configurations exhibit a unified and universal behaviour, captured by a single constitutive relationship between stress, strain and time as: σ+Aσ̇+Bσ¨=Pε̇+Qε¨. The ensuing stress-relaxation G(t) and creep J(t) functions are also unified and universal, derived as [Formula: see text] and J(t)=c2+(ε0-c2)e(-PQt)+σ0Pt, respectively. Application of these relationships to experimental data is illustrated for various tissues including the aortic valve, ligament and cerebral artery. The unified model presented in this paper may be applied to all tissues with two characteristic times, obviating the need for employing varied configurations of discrete element models in preliminary investigation of the viscoelastic behaviour of soft tissues. Copyright © 2015 Elsevier Ltd. All rights reserved.

A Hybrid Approach to Composite Damage and Failure Analysis Combining Synergistic Damage Mechanics and Peridynamics

DTIC Science & Technology

2016-09-30

far from uniform . The final nonuniform distribution of fibers consists of clustered regions and resin pockets. The clustered fiber regions promote...period. Approach and Results A novel procedure has been devised to create nonuniform fiber distributions from the initial fiber bundle (with...used in simulations to produce nonuniform configurations. 2 . , •• ... . .. ·~ · . .. 000 8oa~.f𔄂oo o0~&mt~ go ... ·~· %(1 "’ ,~o ooif-l /j

Proceedings of the 1982 Army Numerical Analysis and Computers Conference.

DTIC Science & Technology

1982-08-01

field array WACC (l,J). Configuration types. The cartesian coordinates of the points on the entire boundary of the physical region, i.e., the closed outer...the field array WACC . This calculation is discussed in Ref.[8],where it is noted that the values obtained are not truly optimum in all cases...placed in the field 60 4g array WACC . The addition to the control functions from attraction to specified lines and/or points in the physical region is

Zeeman-hyperfine structures and isotope effect in the spectrum of Tl I

NASA Astrophysics Data System (ADS)

Bouazza, Safa; Sobolewski, Łukasz Marek; Kwela, Jerzy

2018-01-01

The Zeeman structures of seventeen lines of 205Tl I (Z = 81) covering the UV-NIR spectral range (351.92-1151.28) nm were investigated. Landé gJ-factors for eighteen levels were determined for the first time. Furthermore, we have performed fine structure studies for both even- and odd-configuration levels and determined the relevant parameters. For the 6 s 6p2 configuration we have refined the suggested level energies and predicted positions for missing levels. With regard to hyperfine structure (hfs), we have justified the surprisingly huge value of the magnetic hfs constant A(6s2 10 s) . Moreover, we have extracted the single-electron hfs constant parameter values for the lowest even-parity configurations of 205Tl I; for instance a10s10 (6s2 10 s) = 1015(9) MHz and a6s10 (6 s 6p2) = 217306(205) MHz. Regarding isotope shift analysis we have observed that Dirac-Fock calculations, preferably chosen to take into account the contribution of the p1/2 contact-electron, are in good agreement with experimental data for low-lying levels of each configuration under study.

Evaluation of a new 240-μm single-use holmium:YAG optical fiber for flexible ureteroscopy.

PubMed

Khemees, Tariq A; Shore, David M; Antiporda, Michael; Teichman, Joel M H; Knudsen, Bodo E

2013-04-01

Numerous holmium:yttrium-aluminum-garnet laser fibers are available for flexible ureteroscopy. Performance and durability of fibers can vary widely among different manufacturers and their product lines with differences within a single product line have been reported. We sought to evaluate a newly developed nontapered, single-use 240-μm fiber, Flexiva™ 200 (Boston Scientific, Natick, MA), during clinical use and in a bench-testing model. A total of 100 new fibers were tested after their use in 100 consecutive flexible ureteroscopic lithotripsy procedures by a single surgeon (B.K.). Prospectively recorded clinical parameters were laser pulse energy and frequency settings, total energy delivered and fibers failure. Subsequently, each fiber was bench-tested using an established protocol. Parameters evaluated for were fibers true diameter, flexibility, tip degradation, energy transmission in straight and 180° bend configuration and fibers failure threshold with stress testing. The mean total energy delivered was 2.20 kJ (range 0-18.24 kJ) and most common laser settings used were 0.8 J at 8 Hz, 0.2 J at 50 Hz, and 1.0 J at 10 Hz, respectively. No fiber fractured during clinical procedures. The true fiber diameter was 450 μm. Fiber tips burnt back an average of 1.664 mm, but were highly variable. With laser setting of 400 mJ at 5 Hz, the mean energy transmitted was 451 and 441 mJ in straight and 180° bend configuration, respectively. Thirteen percent of fibers fractured at the bend radius of 0.5 cm with a positive correlation to the total energy transmitted during clinical use identified. Fiber performance was consistent in terms of energy transmission and resistance to fracture when activated in bent configuration. Fiber failure during stress testing showed significant correlation with the total energy delivered during the clinical procedure. The lack of fiber fracture during clinical use may reduce the risk of flexible endoscope damage due to fiber failure.

Fine- and hyperfine structure investigations of even configuration system of atomic terbium

NASA Astrophysics Data System (ADS)

Stefanska, D.; Elantkowska, M.; Ruczkowski, J.; Furmann, B.

2017-03-01

In this work a parametric study of the fine structure (fs) and the hyperfine structure (hfs) for the even-parity configurations of atomic terbium (Tb I) is presented, based in considerable part on the new experimental results. Measurements on 134 spectral lines were performed by laser induced fluorescence (LIF) in a hollow cathode discharge lamp; on this basis, the hyperfine structure constants A and B were determined for 52 even-parity levels belonging to the configurations 4f85d6s2, 4f85d26s or 4f96s6p; in all the cases those levels were involved in the transitions investigated as the lower levels. For 40 levels the hfs was examined for the first time, and for the remaining 12 levels the new measurements supplement our earlier results. As a by-product, also preliminary values of the hfs constants for 84 odd-parity levels were determined (the investigations of the odd-parity levels system in the terbium atom are still in progress). This huge amount of new experimental data, supplemented by our earlier published results, were considered for the fine and hyperfine structure analysis. A multi-configuration fit of 7 configurations was performed, taking into account second-order of perturbation theory, including the effects of closed shell-open shell excitations. Predicted values of the level energies, as well as of magnetic dipole and electric quadrupole hyperfine structure constants A and B, are quoted in cases when no experimental values are available. By combining our experimental data with our own semi-empirical procedure it was possible to identify correctly the lower and upper level of the line 544.1440 nm measured by Childs with the use of the atomic-beam laser-rf double-resonance technique (Childs, J Opt Soc Am B 9;1992:191-6).

Titanium and advanced composite structures for a supersonic cruise arrow wing configuration

NASA Technical Reports Server (NTRS)

Turner, M. J.; Hoy, J. M.

1976-01-01

Structural design studies were made, based on current technology and on an estimate of technology to be available in the mid 1980's, to assess the relative merits of structural concepts and materials for an advanced arrow wing configuration cruising at Mach 2.7. Preliminary studies were made to insure compliance of the configuration with general design criteria, integrate the propulsion system with the airframe, and define an efficient structural arrangement. Material and concept selection, detailed structural analysis, structural design and airplane mass analysis were completed based on current technology. Based on estimated future technology, structural sizing for strength and a preliminary assessment of the flutter of a strength designed composite structure were completed. An advanced computerized structural design system was used, in conjunction with a relatively complex finite element model, for detailed analysis and sizing of structural members.

A systems engineering analysis of three-point and four-point wind turbine drivetrain configurations

DOE PAGES

Guo, Yi; Parsons, Tyler; Dykes, Katherine; ...

2016-08-24

This study compares the impact of drivetrain configuration on the mass and capital cost of a series of wind turbines ranging from 1.5 MW to 5.0 MW power ratings for both land-based and offshore applications. The analysis is performed with a new physics-based drivetrain analysis and sizing tool, Drive Systems Engineering (DriveSE), which is part of the Wind-Plant Integrated System Design & Engineering Model. DriveSE uses physics-based relationships to size all major drivetrain components according to given rotor loads simulated based on International Electrotechnical Commission design load cases. The model's sensitivity to input loads that contain a high degree ofmore » variability was analyzed. Aeroelastic simulations are used to calculate the rotor forces and moments imposed on the drivetrain for each turbine design. DriveSE is then used to size all of the major drivetrain components for each turbine for both three-point and four-point configurations. The simulation results quantify the trade-offs in mass and component costs for the different configurations. On average, a 16.7% decrease in total nacelle mass can be achieved when using a three-point drivetrain configuration, resulting in a 3.5% reduction in turbine capital cost. This analysis is driven by extreme loads and does not consider fatigue. Thus, the effects of configuration choices on reliability and serviceability are not captured. Furthermore, a first order estimate of the sizing, dimensioning and costing of major drivetrain components are made which can be used in larger system studies which consider trade-offs between subsystems such as the rotor, drivetrain and tower.« less

A systems engineering analysis of three-point and four-point wind turbine drivetrain configurations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guo, Yi; Parsons, Tyler; Dykes, Katherine

This study compares the impact of drivetrain configuration on the mass and capital cost of a series of wind turbines ranging from 1.5 MW to 5.0 MW power ratings for both land-based and offshore applications. The analysis is performed with a new physics-based drivetrain analysis and sizing tool, Drive Systems Engineering (DriveSE), which is part of the Wind-Plant Integrated System Design & Engineering Model. DriveSE uses physics-based relationships to size all major drivetrain components according to given rotor loads simulated based on International Electrotechnical Commission design load cases. The model's sensitivity to input loads that contain a high degree ofmore » variability was analyzed. Aeroelastic simulations are used to calculate the rotor forces and moments imposed on the drivetrain for each turbine design. DriveSE is then used to size all of the major drivetrain components for each turbine for both three-point and four-point configurations. The simulation results quantify the trade-offs in mass and component costs for the different configurations. On average, a 16.7% decrease in total nacelle mass can be achieved when using a three-point drivetrain configuration, resulting in a 3.5% reduction in turbine capital cost. This analysis is driven by extreme loads and does not consider fatigue. Thus, the effects of configuration choices on reliability and serviceability are not captured. Furthermore, a first order estimate of the sizing, dimensioning and costing of major drivetrain components are made which can be used in larger system studies which consider trade-offs between subsystems such as the rotor, drivetrain and tower.« less

KINETIC-J: A computational kernel for solving the linearized Vlasov equation applied to calculations of the kinetic, configuration space plasma current for time harmonic wave electric fields

NASA Astrophysics Data System (ADS)

Green, David L.; Berry, Lee A.; Simpson, Adam B.; Younkin, Timothy R.

2018-04-01

We present the KINETIC-J code, a computational kernel for evaluating the linearized Vlasov equation with application to calculating the kinetic plasma response (current) to an applied time harmonic wave electric field. This code addresses the need for a configuration space evaluation of the plasma current to enable kinetic full-wave solvers for waves in hot plasmas to move beyond the limitations of the traditional Fourier spectral methods. We benchmark the kernel via comparison with the standard k →-space forms of the hot plasma conductivity tensor.

Conference Proceedings of Applications of Mesh Generation to Complex 3-D Configurations Held at the Specialists’ Meeting of the Fluid Dynamics Panel in Leon, Norway on 24th-25th May 1989

DTIC Science & Technology

1990-03-01

Computations, edited by I. Babu ka, 0. C . Zienkiewicz, J. Gago, and E. R. de A. Oliveira ( John Wiley and Sons, New York, 1986), p. 281. [4] B. Wedan and J...GENERATION TO COMPLEX 3-D CONFIGURATIONS ., " c 1- For Papers presented and discussion- held at the Specialists’ Meeting of the Fluid Dynamics Panel in...the Panels which are composed of experts appointed by the National Delegates. the Consultant and Fxch., ., c Progi amime and the Aerospace Applications

The Selection of Q-Switch for a 350mJ Air-borne 2-micron Wind Lidar

NASA Technical Reports Server (NTRS)

Petros, Mulugeta; Yu, Jirong; Trieu, Bo; Bai, Yingxin; Petzar, Paul; Singh, Upendra N.

2008-01-01

In the process of designing a coherent, high energy 2micron, Doppler wind Lidar, various types of Q-Switch materials and configurations have been investigated for the oscillator. Designing an oscillator with a relatively low gain laser material, presents challenges related to the management high internal circulating fluence due to high reflective output coupler. This problem is compounded by the loss of hold-off. In addition, the selection has to take into account the round trip optical loss in the resonator and the loss of hold-off. For this application, a Brewster cut 5mm aperture, fused silica AO Q-switch is selected. Once the Q-switch is selected various rf frequencies were evaluated. Since the Lidar has to perform in single longitudinal and transverse mode with transform limited line width, in this paper, various seeding configurations are presented in the context of Q-Switch diffraction efficiency. The master oscillator power amplifier has demonstrated over 350mJ output when the amplifier is operated in double pass mode and higher than 250mJ when operated in single pass configuration. The repetition rate of the system is 10Hz and the pulse length 200ns.

Polarization effects in the interaction between multi-level atoms and two optical fields

NASA Astrophysics Data System (ADS)

Colín-Rodríguez, R.; Flores-Mijangos, J.; Hernández-Gómez, S.; Jáuregui, R.; López-Hernández, O.; Mojica-Casique, C.; Ponciano-Ojeda, F.; Ramírez-Martínez, F.; Sahagún, D.; Volke-Sepúlveda, K.; Jiménez-Mier, J.

2015-06-01

Polarized velocity selective spectra for rubidium atoms in a room temperature cell are presented. The experiments were performed in the lambda configuration (D2 manifold) and in the 5s\\to 5{{p}3/2}\\to 5{{d}j} ladder configuration. For the lambda configuration the effect of the probe beam intensity in the absorption and polarization spectra are compared with results of a rate equation approximation. Good overall agreement between experiment and theory is found. The results indicate different saturation rates for each of the atomic transitions. Distinctive polarization signals with hyperfine-resolved components are found for the ladder 5{{d}3/2} and 5{{d}5/2} upper states. Fluorescence detection of the 420 nm that results from the second step in the cascade decay 5{{d}j}\\to 6{{p}{{j\\prime }}}\\to 5s was used in the ladder experiments. This fluorescence was also used for the detection of the 5{{p}3/2}\\to 6{{p}3/2} electric dipole forbidden transition in atomic rubidium that occurs at 911 nm. The 6{{p}3/2} hyperfine structure was resolved in this continuous wave, non-dipole excitation.

(Quasi)-convexification of Barta's (multi-extrema) bounding theorem: Inf_x\\big(\\ssty\\frac{H\\Phi(x)}{\\Phi(x)} \\big) \\le E_gr \\le Sup_x \\big(\\ssty\\frac{H\\Phi(x)}{\\Phi(x)} \\big)

NASA Astrophysics Data System (ADS)

Handy, C. R.

2006-03-01

There has been renewed interest in the exploitation of Barta's configuration space theorem (BCST) (Barta 1937 C. R. Acad. Sci. Paris 204 472) which bounds the ground-state energy, Inf_x\\big({{H\\Phi(x)}\\over {\\Phi(x)}} \\big ) \\leq E_gr \\leq Sup_x \\big({{H\\Phi(x)}\\over {\\Phi(x)}}\\big) , by using any Φ lying within the space of positive, bounded, and sufficiently smooth functions, {\\cal C} . Mouchet's (Mouchet 2005 J. Phys. A: Math. Gen. 38 1039) BCST analysis is based on gradient optimization (GO). However, it overlooks significant difficulties: (i) appearance of multi-extrema; (ii) inefficiency of GO for stiff (singular perturbation/strong coupling) problems; (iii) the nonexistence of a systematic procedure for arbitrarily improving the bounds within {\\cal C} . These deficiencies can be corrected by transforming BCST into a moments' representation equivalent, and exploiting a generalization of the eigenvalue moment method (EMM), within the context of the well-known generalized eigenvalue problem (GEP), as developed here. EMM is an alternative eigenenergy bounding, variational procedure, overlooked by Mouchet, which also exploits the positivity of the desired physical solution. Furthermore, it is applicable to Hermitian and non-Hermitian systems with complex-number quantization parameters (Handy and Bessis 1985 Phys. Rev. Lett. 55 931, Handy et al 1988 Phys. Rev. Lett. 60 253, Handy 2001 J. Phys. A: Math. Gen. 34 5065, Handy et al 2002 J. Phys. A: Math. Gen. 35 6359). Our analysis exploits various quasi-convexity/concavity theorems common to the GEP representation. We outline the general theory, and present some illustrative examples.

Optical sensor in planar configuration based on multimode interference

NASA Astrophysics Data System (ADS)

Blahut, Marek

2017-08-01

In the paper a numerical analysis of optical sensors based on multimode interference in planar one-dimensional step-index configuration is presented. The structure consists in single-mode input and output waveguides and multimode waveguide which guide only few modes. Material parameters discussed refer to a SU8 polymer waveguide on SiO2 substrate. The optical system described will be designed to the analysis of biological substances.

Modified Bayesian Kriging for Noisy Response Problems for Reliability Analysis

DTIC Science & Technology

2015-01-01

52242, USA nicholas-gaul@uiowa.edu Mary Kathryn Cowles Department of Statistics & Actuarial Science College of Liberal Arts and Sciences , The...Forrester, A. I. J., & Keane, A. J. (2009). Recent advances in surrogate-based optimization. Progress in Aerospace Sciences , 45(1–3), 50-79. doi...Wiley. [27] Sacks, J., Welch, W. J., Toby J. Mitchell, & Wynn, H. P. (1989). Design and analysis of computer experiments. Statistical Science , 4

50th Annual Fuze Conference. Session 1 and 2

DTIC Science & Technology

2006-05-11

PROGRAM OFFICE AMSRD-AAR-AIJ J. Goldman X6060 STRATEGIC MGT OFFICE AMSRD-AAR-EMS D. Denery X6081 KNOWLEDGE MANAGEMENT OFFICE AMSRD-AAR-EMK G. Albinson...Tail-Mounted Configuration (MK-82 Demo) UHF to L-Band Pulse Doppler Radar Using Low Cost COTS Components Nose and Tail Mount Configurations Only

Theoretical calculations of rotationally inelastic collisions of He with NaK(A (1)Σ(+)): Transfer of population, orientation, and alignment.

PubMed

Malenda, R F; Price, T J; Stevens, J; Uppalapati, S L; Fragale, A; Weiser, P M; Kuczala, A; Talbi, D; Hickman, A P

2015-06-14

We have performed extensive calculations to investigate thermal energy, rotationally inelastic collisions of NaK (A(1)Σ(+)) with He. We determined a potential energy surface using a multi-reference configuration interaction wave function as implemented by the GAMESS electronic structure code, and we have performed coupled channel scattering calculations using the Arthurs and Dalgarno formalism. We also calculate the Grawert coefficients B(λ)(j, j') for each j → j' transition. These coefficients are used to determine the probability that orientation and alignment are preserved in collisions taking place in a cell environment. The calculations include all rotational levels with j or j' between 0 and 50, and total (translational and rotational) energies in the range 0.0002-0.0025 a.u. (∼44-550 cm(-1)). The calculated cross sections for transitions with even values of Δj tend to be larger than those for transitions with odd Δj, in agreement with the recent experiments of Wolfe et al. (J. Chem. Phys. 134, 174301 (2011)). The calculations of the energy dependence of the cross sections and the calculations of the fraction of orientation and alignment preserved in collisions also exhibit distinctly different behaviors for odd and even values of Δj. The calculations also indicate that the average fraction of orientation or alignment preserved in a transition becomes larger as j increases. We interpret this behavior using the semiclassical model of Derouard, which also leads to a simple way of visualizing the distribution of the angles between the initial and final angular momentum vectors j and j'. Finally, we compare the exact quantum results for j → j' transitions with results based on the simpler, energy sudden approximation. That approximation is shown to be quite accurate.

Implementation of olfactory bulb glomerular-layer computations in a digital neurosynaptic core.

PubMed

Imam, Nabil; Cleland, Thomas A; Manohar, Rajit; Merolla, Paul A; Arthur, John V; Akopyan, Filipp; Modha, Dharmendra S

2012-01-01

We present a biomimetic system that captures essential functional properties of the glomerular layer of the mammalian olfactory bulb, specifically including its capacity to decorrelate similar odor representations without foreknowledge of the statistical distributions of analyte features. Our system is based on a digital neuromorphic chip consisting of 256 leaky-integrate-and-fire neurons, 1024 × 256 crossbar synapses, and address-event representation communication circuits. The neural circuits configured in the chip reflect established connections among mitral cells, periglomerular cells, external tufted cells, and superficial short-axon cells within the olfactory bulb, and accept input from convergent sets of sensors configured as olfactory sensory neurons. This configuration generates functional transformations comparable to those observed in the glomerular layer of the mammalian olfactory bulb. Our circuits, consuming only 45 pJ of active power per spike with a power supply of 0.85 V, can be used as the first stage of processing in low-power artificial chemical sensing devices inspired by natural olfactory systems.

Determination of Hund's coupling in 5 d oxides using resonant inelastic x-ray scattering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yuan, Bo; Clancy, J. P.; Cook, A. M.

2017-06-01

We report resonant inelastic x-ray scattering (RIXS) measurements on ordered double-perovskite samples containing Re5+ and Ir5+ with 5d(2) and 5d(4) electronic configurations, respectively. In particular, the observedRIXS spectra of Ba2YReO6 and Sr2MIrO6 (M = Y, Gd) show sharp intra-t(2g) transitions, which can be quantitatively understood using a minimal "atomic" Hamiltonian incorporating spin-orbit coupling. and Hund's coupling J(H). Our analysis yields lambda = 0.38(2) eV with J(H) = 0.26(2) eV for Re5+ and lambda = 0.42(2) eV with J(H) = 0.25(4) eV for Ir5+. Our results provide sharp estimates for Hund's coupling in 5d oxides and suggest that it should bemore » treated on equal footing with spin-orbit interaction in multiorbital 5d transition-metal compounds.« less

Spin-orbit coupling induced two-electron relaxation in silicon donor pairs

NASA Astrophysics Data System (ADS)

Song, Yang; Das Sarma, S.

2017-09-01

We unravel theoretically a key intrinsic relaxation mechanism among the low-lying singlet and triplet donor-pair states in silicon, an important element in the fast-developing field of spintronics and quantum computation. Despite the perceived weak spin-orbit coupling (SOC) in Si, we find that our discovered relaxation mechanism, combined with the electron-phonon and interdonor interactions, drives the transitions in the two-electron states over a large range of donor coupling regimes. The scaling of the relaxation rate with interdonor exchange interaction J goes from J5 to J4 at the low to high temperature limits. Our analytical study draws on the symmetry analysis over combined band, donor envelope, and valley configurations. It uncovers naturally the dependence on the donor-alignment direction and triplet spin orientation, and especially on the dominant SOC source from donor impurities. While a magnetic field is not necessary for this relaxation, unlike in the single-donor spin relaxation, we discuss the crossover behavior with increasing Zeeman energy in order to facilitate comparison with experiments.

Energy consumption analysis of graphene based all spin logic device with voltage controlled magnetic anisotropy

NASA Astrophysics Data System (ADS)

Zhang, Zhizhong; Zhang, Yue; Zheng, Zhenyi; Wang, Guanda; Su, Li; Zhang, Youguang; Zhao, Weisheng

2017-05-01

All spin logic device (ASLD) is a promising option to realize the ultra-low power computing systems. However, the low spin transport efficiency and the non-local switching of the detector have become two key challenges of the ASLD. In this paper, we analyze the energy consumption of a graphene based ASLD with the ferromagnetic layer switching assistance by voltage control magnetic anisotropy (VCMA) effect. This structure has significant potential towards ultra-low power consumption: the applied voltage can not only shorten switching time of the ferromagnetic layer, but also decreases the critical injection current; the graphene channel enhances greatly the spin transport efficiency. By applying the approximate circuit model, the impact of material configurations, interfaces and geometry can be synthetically studied. An accurate physic model was also developed, based on which, we carry out the micro-magnetic simulations to analyze the magnetization dynamics. Combining these electrical and magnetic investigations, the energy consumption of the proposed ASLD can be estimated. With the optimizing parameters, the energy consumption can be reduced to 2.5 pJ for a logic operation.

Aeroelastic Analysis of Aircraft: Wing and Wing/Fuselage Configurations

NASA Technical Reports Server (NTRS)

Chen, H. H.; Chang, K. C.; Tzong, T.; Cebeci, T.

1997-01-01

A previously developed interface method for coupling aerodynamics and structures is used to evaluate the aeroelastic effects for an advanced transport wing at cruise and under-cruise conditions. The calculated results are compared with wind tunnel test data. The capability of the interface method is also investigated for an MD-90 wing/fuselage configuration. In addition, an aircraft trim analysis is described and applied to wing configurations. The accuracy of turbulence models based on the algebraic eddy viscosity formulation of Cebeci and Smith is studied for airfoil flows at low Mach numbers by using methods based on the solutions of the boundary-layer and Navier-Stokes equations.

High-energy, tunable, mid-infrared, picosecond optical parametric generation in CdSiP2

NASA Astrophysics Data System (ADS)

Chaitanya Kumar, S.; Jelínek, M.; Baudisch, M.; Zawilski, K. T.; Schunemann, P. G.; Kubecek, V.; Biegert, J.; Ebrahim-Zadeh, M.

2012-06-01

We report a tunable, high-energy, single-pass, optical parametric generator (OPG) based on the new nonlinear material, cadmium silicon phosphide, CdSiP2. The OPG is pumped by a laboratory designed cavity-dumped passively mode-locked, diode-pumped, Nd:YAG oscillator, providing 25 μJ pulses in 20 ps at 5 Hz. The pump energy is further boosted by a flashlamp-pumped Nd:YAG amplifier to 2.5 mJ. The OPG is temperature tunable over 1263-1286 nm (23 nm) in the signal and 6153-6731 nm (578 nm) in the idler, corresponding to a total tuning range of 601 nm. Using the single-pass OPG configuration, we have generated signal energy as high as 636 μJ at 1283 nm, together with an idler energy of 33 μJ at 6234 nm, for 2.1 mJ of input pump energy. The signal pulses generated from the OPG have a Gaussian pulse duration of 24 ps and an FWHM spectral bandwidth of 10.4 nm at central wavelength of 1276 nm. The corresponding idler spectrum has an FWHM bandwidth of 140 nm centered at 6404 nm.

Computer controlled performance mapping of thermionic converters: effect of collector, guard-ring potential imbalances on the observed collector current-density, voltage characteristics and limited range performance map of an etched-rhenium, niobium planar converter

NASA Technical Reports Server (NTRS)

Manista, E. J.

1972-01-01

The effect of collector, guard-ring potential imbalance on the observed collector-current-density J, collector-to-emitter voltage V characteristic was evaluated in a planar, fixed-space, guard-ringed thermionic converter. The J,V characteristic was swept in a period of 15 msec by a variable load. A computerized data acquisition system recorded test parameters. The results indicate minimal distortion of the J,V curve in the power output quadrant for the nominal guard-ring circuit configuration. Considerable distortion, along with a lowering of the ignited-mode striking voltage, was observed for the configuration with the emitter shorted to the guard ring. A limited-range performance map of an etched-rhenium, niobium, planar converter was obtained by using an improved computer program for the data acquisition system.

Fabrication of Metallic Magnetic Calorimeter for Radionuclide Analysis

NASA Astrophysics Data System (ADS)

Yoon, W. S.; Kim, G. B.; Lee, H. J.; Lee, J. Y.; Lee, J. H.; Jang, Y. S.; Lee, S. J.; Lee, M. K.; Kim, Y. H.

2014-09-01

We present a detailed report on the fabrication process of a metallic magnetic calorimeter (MMC). The MMC is configured in a planar geometry with a meander-shaped pickup coil covered with a Au:Er temperature sensor layer. The meander coil is used to apply a magnetic field to magnetize the erbium ions and to measure the magnetization change of the spin system. The MMC is designed to have a large area (1 mm) and 3 m thickness Au:Er layer, which is suited for large metal absorbers with a few nJ/K heat capacity in radionuclide analysis applications. The completed devices are used in alpha and Q spectrometries.

Laser damage threshold measurements of microstructure-based high reflectors

NASA Astrophysics Data System (ADS)

Hobbs, Douglas S.

2008-10-01

In 2007, the pulsed laser induced damage threshold (LIDT) of anti-reflecting (AR) microstructures built in fused silica and glass was shown to be up to three times greater than the LIDT of single-layer thin-film AR coatings, and at least five times greater than multiple-layer thin-film AR coatings. This result suggested that microstructure-based wavelength selective mirrors might also exhibit high LIDT. Efficient light reflection over a narrow spectral range can be produced by an array of sub-wavelength sized surface relief microstructures built in a waveguide configuration. Such surface structure resonant (SSR) filters typically achieve a reflectivity exceeding 99% over a 1-10nm range about the filter center wavelength, making SSR filters useful as laser high reflectors (HR). SSR laser mirrors consist of microstructures that are first etched in the surface of fused silica and borosilicate glass windows and subsequently coated with a thin layer of a non-absorbing high refractive index dielectric material such as tantalum pent-oxide or zinc sulfide. Results of an initial investigation into the LIDT of single layer SSR laser mirrors operating at 532nm, 1064nm and 1573nm are described along with data from SEM analysis of the microstructures, and spectral reflection measurements. None of the twelve samples tested exhibited damage thresholds above 3 J/cm2 when illuminated at the resonant wavelength, indicating that the simple single layer, first order design will need further development to be suitable for high power laser applications. Samples of SSR high reflectors entered in the Thin Film Damage Competition also exhibited low damage thresholds of less than 1 J/cm2 for the ZnS coated SSR, and just over 4 J/cm2 for the Ta2O5 coated SSR.

Four-wave-mixing suppression in Er 3+-fiber amplifiers by backward pumping

NASA Astrophysics Data System (ADS)

Adel, P.; Engelbrecht, M.; Wandt, D.; Fallnich, C.

2007-03-01

Amplification of chirped fs-pulses in an Erbium doped fiber amplifier upto 0.8 μJ resulted in an additional peak in the spectrum at 1584 nm. This peak, attributable to four-wave-mixing between the signal centered at 1559 nm and amplified spontaneous emission at 1534 nm, hinders the temporal recompression of the amplified chirped pulse. Compared to the forward pumping configuration, this four-wave-mixing in the amplifier was largely reduced in a backward pumping configuration. Based on simulations, explanations for the observed influence of the pump direction on the four-wave-mixing efficiency are presented. The results pointed out that the gain spectrum distribution along the fiber strongly influences four-wave-mixing effects in fiber amplifiers even for constant overall gain spectrum.

Investigation of turbines for driving supersonic compressors II : performance of first configuration with 2.2 percent reduction in nozzle flow area / Warner L. Stewart, Harold J. Schum, Robert Y. Wong

NASA Technical Reports Server (NTRS)

Stewart, Warner L; Schum, Harold J; Wong, Robert Y

1952-01-01

The experimental performance of a modified turbine for driving a supersonic compressor is presented and compared with the performance of the original configuration to illustrate the effect of small changes in the ratio of nozzle-throat area to rotor-throat area. Performance is based on the performance of turbines designed to operate with both blade rows close to choking. On the basis of the results of this investigation, the ratio of areas is concluded to become especially critical in the design of turbines such as those designed to drive high-speed, high-specific weight-flow compressors where the turbine nozzles and rotor are both very close to choking.

The Consequences of Spin-Orbit Coupling on the 5d3 Electronic Configuration

NASA Astrophysics Data System (ADS)

Christianson, A. D.

The impact of spin-orbit coupling on collective properties of matter is of considerable interest. The most intensively investigated materials in this regard are Iridium-based transition metal oxides which exhibit a host of interesting ground states that originate from a 5d5 Jeff = 1/2 electronic configuration. Moving beyond the Jeff = 1/2 paradigm to other electronic configurations where spin-orbit coupling plays a prominent role is a key objective of ongoing research. Here we focus on several Osmium-based transition metal oxides such as NaOsO3, Cd2Os2O7, Ca3LiOsO6, Sr2ScOsO6, Ba2YOsO6, and Sr2FeOsO6, which are nominally in the 5d3 electronic configuration. Within the LS coupling picture and a strong octahedral crystal field, the 5d3 configuration is expected to be an orbital singlet and spin-orbit effects should be minimal. Nevertheless, our neutron and x-ray scattering investigations of these materials as well as investigations by other groups show dramatic effects of spin-orbit coupling including reduced moment magnetic order, enhanced spin-phonon coupling, and large spin gaps. In particular, the anisotropy induced by spin-orbit coupling tips the balance of the frustrated interactions and drives the selection of particular magnetic ground states. To understand the mechanism driving the spin-orbit effects, we have explored the ground state t2g manifold with resonant inelastic x-ray scattering and observe a spectrum inexplicable by an LS coupling picture. On the other hand, an intermediate coupling approach reveals that the ground state wave function is a J =3/2 configuration which answers the question of how strong spin-orbit coupling effects arise in 5d3 systems.

Measurement Model and Precision Analysis of Accelerometers for Maglev Vibration Isolation Platforms.

PubMed

Wu, Qianqian; Yue, Honghao; Liu, Rongqiang; Zhang, Xiaoyou; Ding, Liang; Liang, Tian; Deng, Zongquan

2015-08-14

High precision measurement of acceleration levels is required to allow active control for vibration isolation platforms. It is necessary to propose an accelerometer configuration measurement model that yields such a high measuring precision. In this paper, an accelerometer configuration to improve measurement accuracy is proposed. The corresponding calculation formulas of the angular acceleration were derived through theoretical analysis. A method is presented to minimize angular acceleration noise based on analysis of the root mean square noise of the angular acceleration. Moreover, the influence of installation position errors and accelerometer orientation errors on the calculation precision of the angular acceleration is studied. Comparisons of the output differences between the proposed configuration and the previous planar triangle configuration under the same installation errors are conducted by simulation. The simulation results show that installation errors have a relatively small impact on the calculation accuracy of the proposed configuration. To further verify the high calculation precision of the proposed configuration, experiments are carried out for both the proposed configuration and the planar triangle configuration. On the basis of the results of simulations and experiments, it can be concluded that the proposed configuration has higher angular acceleration calculation precision and can be applied to different platforms.

Measurement Model and Precision Analysis of Accelerometers for Maglev Vibration Isolation Platforms

PubMed Central

Wu, Qianqian; Yue, Honghao; Liu, Rongqiang; Zhang, Xiaoyou; Ding, Liang; Liang, Tian; Deng, Zongquan

2015-01-01

High precision measurement of acceleration levels is required to allow active control for vibration isolation platforms. It is necessary to propose an accelerometer configuration measurement model that yields such a high measuring precision. In this paper, an accelerometer configuration to improve measurement accuracy is proposed. The corresponding calculation formulas of the angular acceleration were derived through theoretical analysis. A method is presented to minimize angular acceleration noise based on analysis of the root mean square noise of the angular acceleration. Moreover, the influence of installation position errors and accelerometer orientation errors on the calculation precision of the angular acceleration is studied. Comparisons of the output differences between the proposed configuration and the previous planar triangle configuration under the same installation errors are conducted by simulation. The simulation results show that installation errors have a relatively small impact on the calculation accuracy of the proposed configuration. To further verify the high calculation precision of the proposed configuration, experiments are carried out for both the proposed configuration and the planar triangle configuration. On the basis of the results of simulations and experiments, it can be concluded that the proposed configuration has higher angular acceleration calculation precision and can be applied to different platforms. PMID:26287203

Bias and robustness of uncertainty components estimates in transient climate projections

NASA Astrophysics Data System (ADS)

Hingray, Benoit; Blanchet, Juliette; Jean-Philippe, Vidal

2016-04-01

A critical issue in climate change studies is the estimation of uncertainties in projections along with the contribution of the different uncertainty sources, including scenario uncertainty, the different components of model uncertainty and internal variability. Quantifying the different uncertainty sources faces actually different problems. For instance and for the sake of simplicity, an estimate of model uncertainty is classically obtained from the empirical variance of the climate responses obtained for the different modeling chains. These estimates are however biased. Another difficulty arises from the limited number of members that are classically available for most modeling chains. In this case, the climate response of one given chain and the effect of its internal variability may be actually difficult if not impossible to separate. The estimate of scenario uncertainty, model uncertainty and internal variability components are thus likely to be not really robust. We explore the importance of the bias and the robustness of the estimates for two classical Analysis of Variance (ANOVA) approaches: a Single Time approach (STANOVA), based on the only data available for the considered projection lead time and a time series based approach (QEANOVA), which assumes quasi-ergodicity of climate outputs over the whole available climate simulation period (Hingray and Saïd, 2014). We explore both issues for a simple but classical configuration where uncertainties in projections are composed of two single sources: model uncertainty and internal climate variability. The bias in model uncertainty estimates is explored from theoretical expressions of unbiased estimators developed for both ANOVA approaches. The robustness of uncertainty estimates is explored for multiple synthetic ensembles of time series projections generated with MonteCarlo simulations. For both ANOVA approaches, when the empirical variance of climate responses is used to estimate model uncertainty, the bias is always positive. It can be especially high with STANOVA. In the most critical configurations, when the number of members available for each modeling chain is small (< 3) and when internal variability explains most of total uncertainty variance (75% or more), the overestimation is higher than 100% of the true model uncertainty variance. The bias can be considerably reduced with a time series ANOVA approach, owing to the multiple time steps accounted for. The longer the transient time period used for the analysis, the larger the reduction. When a quasi-ergodic ANOVA approach is applied to decadal data for the whole 1980-2100 period, the bias is reduced by a factor 2.5 to 20 depending on the projection lead time. In all cases, the bias is likely to be not negligible for a large number of climate impact studies resulting in a likely large overestimation of the contribution of model uncertainty to total variance. For both approaches, the robustness of all uncertainty estimates is higher when more members are available, when internal variability is smaller and/or the response-to-uncertainty ratio is higher. QEANOVA estimates are much more robust than STANOVA ones: QEANOVA simulated confidence intervals are roughly 3 to 5 times smaller than STANOVA ones. Excepted for STANOVA when less than 3 members is available, the robustness is rather high for total uncertainty and moderate for internal variability estimates. For model uncertainty or response-to-uncertainty ratio estimates, the robustness is conversely low for QEANOVA to very low for STANOVA. In the most critical configurations (small number of member, large internal variability), large over- or underestimation of uncertainty components is very thus likely. To propose relevant uncertainty analyses and avoid misleading interpretations, estimates of uncertainty components should be therefore bias corrected and ideally come with estimates of their robustness. This work is part of the COMPLEX Project (European Collaborative Project FP7-ENV-2012 number: 308601; http://www.complex.ac.uk/). Hingray, B., Saïd, M., 2014. Partitioning internal variability and model uncertainty components in a multimodel multireplicate ensemble of climate projections. J.Climate. doi:10.1175/JCLI-D-13-00629.1 Hingray, B., Blanchet, J. (revision) Unbiased estimators for uncertainty components in transient climate projections. J. Climate Hingray, B., Blanchet, J., Vidal, J.P. (revision) Robustness of uncertainty components estimates in climate projections. J.Climate

Beyond-proximity-force-approximation Casimir force between two spheres at finite temperature

NASA Astrophysics Data System (ADS)

Bimonte, Giuseppe

2018-04-01

A recent experiment [J. L. Garrett, D. A. T. Somers, and J. N. Munday, Phys. Rev. Lett. 120, 040401 (2018), 10.1103/PhysRevLett.120.040401] measured for the first time the gradient of the Casimir force between two gold spheres at room temperature. The theoretical analysis of the data was carried out using the standard proximity force approximation (PFA). A fit of the data, using a parametrization of the force valid for the sphere-plate geometry, was used by the authors to place a bound on deviations from PFA. Motivated by this work, we compute the Casimir force between two gold spheres at finite temperature. The semianalytic formula for the Casimir force that we construct is valid for all separations, and can be easily used to interpret future experiments in both the sphere-plate and sphere-sphere configurations. We describe the correct parametrization of the corrections to PFA for two spheres that should be used in data analysis.

Formation of the Martian Polar Layered Terrains: Quantifying Polar Water Ice and Dust Surface Deposition during Current and Past Orbital Epochs with the NASA Ames GCM

NASA Astrophysics Data System (ADS)

Emmett, Jeremy; Murphy, Jim

2016-10-01

Structural and compositional variability in the layering sequences comprising Mars' polar layered terrains (PLT's) is likely explained by orbital-forced climatic variations in the sedimentary cycles of water ice and dust from which they formed [1]. The PLT's therefore contain a direct, extensive record of the recent climate history of Mars encoded in their structure and stratigraphy, but deciphering this record requires understanding the depositional history of their dust and water ice constituents. 3D Mars atmosphere modeling enables direct simulation of atmospheric dynamics, aerosol transport and quantification of surface accumulation for a range of past and present orbital configurations. By quantifying the net yearly polar deposition rates of water ice and dust under Mars' current and past orbital configurations characteristic of the last several millions of years, and integrating these into the present with a time-stepping model, the formation history of the north and south PLT's will be investigated, further constraining their age and composition, and, if reproducible, revealing the processes responsible for prominent features and stratigraphy observed within the deposits. Simulating the formation of the deposits by quantifying net deposition rates during past orbital epochs and integrating these into the present, effectively 'rebuilding' the terrains, could aid in understanding deeper stratigraphic trends, correlating between geographically-separated deposits, explaining the presence and shapes of large-scale polar features, and correlating stratigraphy with geological time. Quantification of the magnitude and geographical distribution of surface aerosol accumulation will build on the work of previous GCM-based investigations [3]. Construction and analysis of hypothetical stratigraphic sequences in the PLT's will draw from previous climate-controlled stratigraphy methodologies [2,4], but will utilize GCM-derived net deposition rates to model orbital influences on sedimentation and erosion.[1] Milkovich S.M. and Head J. W. (2005) JGR, 110. [2] Laskar J.B. and Mustard J.F. (2002) Nature, 419, 375-377 [3] Newman C.E. et al. (2005) Icarus, 174, 135-160. [4] Hvidberg C.S. et al. (2012) Icarus, 221, 405-419.

What is the Best Configuration of Wearable Sensors to Measure Spatiotemporal Gait Parameters in Children with Cerebral Palsy?

PubMed Central

Carcreff, Lena; Paraschiv-Ionescu, Anisoara; De Coulon, Geraldo; Armand, Stéphane; Aminian, Kamiar

2018-01-01

Wearable inertial devices have recently been used to evaluate spatiotemporal parameters of gait in daily life situations. Given the heterogeneity of gait patterns in children with cerebral palsy (CP), the sensor placement and analysis algorithm may influence the validity of the results. This study aimed at comparing the spatiotemporal measurement performances of three wearable configurations defined by different sensor positioning on the lower limbs: (1) shanks and thighs, (2) shanks, and (3) feet. The three configurations were selected based on their potential to be used in daily life for children with CP and typically developing (TD) controls. For each configuration, dedicated gait analysis algorithms were used to detect gait events and compute spatiotemporal parameters. Fifteen children with CP and 11 TD controls were included. Accuracy, precision, and agreement of the three configurations were determined in comparison with an optoelectronic system as a reference. The three configurations were comparable for the evaluation of TD children and children with a low level of disability (CP-GMFCS I) whereas the shank-and-thigh-based configuration was more robust regarding children with a higher level of disability (CP-GMFCS II–III). PMID:29385700

A Computational Architecture for Programmable Automation Research

NASA Astrophysics Data System (ADS)

Taylor, Russell H.; Korein, James U.; Maier, Georg E.; Durfee, Lawrence F.

1987-03-01

This short paper describes recent work at the IBM T. J. Watson Research Center directed at developing a highly flexible computational architecture for research on sensor-based programmable automation. The system described here has been designed with a focus on dynamic configurability, layered user inter-faces and incorporation of sensor-based real time operations into new commands. It is these features which distinguish it from earlier work. The system is cur-rently being implemented at IBM for research purposes and internal use and is an outgrowth of programmable automation research which has been ongoing since 1972 [e.g., 1, 2, 3, 4, 5, 6] .

Allowed Vales of J in jj coupling of Equivalent Electrons.

ERIC Educational Resources Information Center

Tuttle, E. R.

1980-01-01

Provides a simple method for finding the values of the total angular momentum J for configurations of equivalent electrons in jj coupling. Shows how a knowledge of both the LS and jj terms can contribute to the students' understanding of the role of different representations in quantum mechanics. (Author/GS)

Color superconductivity in compact stellar hybrid configurations

NASA Astrophysics Data System (ADS)

Ranea-Sandoval, Ignacio F.; Orsaria, Milva G.; Han, Sophia; Weber, Fridolin; Spinella, William M.

2017-12-01

The discovery of pulsars PSR J1614-2230 and PSR J0348+0432 with masses of around 2 M⊙ imposes strong constraints on the equations of state of cold, ultradense matter. If a phase transition from hadronic matter to quark matter were to occur in the inner cores of such massive neutron stars, the energetically favorable state of quark matter would be a color superconductor. In this study, we analyze the stability and maximum mass of such neutron stars. The hadronic phase is described by nonlinear relativistic mean-field models, and the local Nambu-Jona Lasinio model is used to describe quark matter in the 2SC+s quark phase. The phase transition is treated as a Maxwell transition, assuming a sharp hadron-quark interface, and the "constant-sound-speed" (CSS) parametrization is employed to discuss the existence of stellar twin configurations. We find that massive neutron stars such as J1614-2230 and J0348+0432 can only exist on the connected stellar branch but not on the disconnected twin-star branch. The latter can only support stars with masses that are strictly below 2 M⊙ .

Plasma Equilibria With Stochastic Magnetic Fields

NASA Astrophysics Data System (ADS)

Krommes, J. A.; Reiman, A. H.

2009-05-01

Plasma equilibria that include regions of stochastic magnetic fields are of interest in a variety of applications, including tokamaks with ergodic limiters and high-pressure stellarators. Such equilibria are examined theoretically, and a numerical algorithm for their construction is described.^2,3 % The balance between stochastic diffusion of magnetic lines and small effects^2 omitted from the simplest MHD description can support pressure and current profiles that need not be flattened in stochastic regions. The diffusion can be described analytically by renormalizing stochastic Langevin equations for pressure and parallel current j, with particular attention being paid to the satisfaction of the periodicity constraints in toroidal configurations with sheared magnetic fields. The equilibrium field configuration can then be constructed by coupling the prediction for j to Amp'ere's law, which is solved numerically. A. Reiman et al., Pressure-induced breaking of equilibrium flux surfaces in the W7AS stellarator, Nucl. Fusion 47, 572--8 (2007). J. A. Krommes and A. H. Reiman, Plasma equilibrium in a magnetic field with stochastic regions, submitted to Phys. Plasmas. J. A. Krommes, Fundamental statistical theories of plasma turbulence in magnetic fields, Phys. Reports 360, 1--351.

Concentrations and toxicity of fumonisin B1 in fermented corn grits are reduced by extrusion cooking with glucose supplementation

USDA-ARS?s Scientific Manuscript database

Extrusion is a cooking method in which dough is forced under high pressure through a heated barrel using one (single-screw configuration) or two (twin-screw configuration) augers. In an earlier experiment (Voss et al., J. Food Protec. 71: 2036-2041, 2008), extrusion using the single screw configura...

Toward Automating Web Protocol Configuration for a Programmable Logic Controller Emulator

DTIC Science & Technology

2014-06-19

Security Risks for Industrial Control Systems ,” VDE 2004 Congress, Berlin, Germany, October 2004, pp. 1-7. [Cis12] Cisco, NetFlow Configuration Guide...Date 29 May 2014 Date AFIT-ENG-T-14-J-4 Abstract Industrial Control Systems (ICS) remain vulnerable through attack vectors that exist within programmable...5 2.2 Industrial Control Systems

Weather Research and Forecasting Model Wind Sensitivity Study at Edwards Air Force Base, CA

NASA Technical Reports Server (NTRS)

Watson, Leela R.; Bauman, William H., III; Hoeth, Brian

2009-01-01

This abstract describes work that will be done by the Applied Meteorology Unit (AMU) in assessing the success of different model configurations in predicting "wind cycling" cases at Edwards Air Force Base, CA (EAFB), in which the wind speeds and directions oscillate among towers near the EAFB runway. The Weather Research and Forecasting (WRF) model allows users to choose among two dynamical cores - the Advanced Research WRF (ARW) and the Non-hydrostatic Mesoscale Model (NMM). There are also data assimilation analysis packages available for the initialization of the WRF model - the Local Analysis and Prediction System (LAPS) and the Advanced Regional Prediction System (ARPS) Data Analysis System (ADAS). Having a series of initialization options and WRF cores, as well as many options within each core, creates challenges for local forecasters, such as determining which configuration options are best to address specific forecast concerns. The goal of this project is to assess the different configurations available and determine which configuration will best predict surface wind speed and direction at EAFB.

Analyzing Visibility Configurations.

PubMed

Dachsbacher, C

2011-04-01

Many algorithms, such as level of detail rendering and occlusion culling methods, make decisions based on the degree of visibility of an object, but do not analyze the distribution, or structure, of the visible and occluded regions across surfaces. We present an efficient method to classify different visibility configurations and show how this can be used on top of existing methods based on visibility determination. We adapt co-occurrence matrices for visibility analysis and generalize them to operate on clusters of triangular surfaces instead of pixels. We employ machine learning techniques to reliably classify the thus extracted feature vectors. Our method allows perceptually motivated level of detail methods for real-time rendering applications by detecting configurations with expected visual masking. We exemplify the versatility of our method with an analysis of area light visibility configurations in ray tracing and an area-to-area visibility analysis suitable for hierarchical radiosity refinement. Initial results demonstrate the robustness, simplicity, and performance of our method in synthetic scenes, as well as real applications.

Comparison between four dissimilar solar panel configurations

NASA Astrophysics Data System (ADS)

Suleiman, K.; Ali, U. A.; Yusuf, Ibrahim; Koko, A. D.; Bala, S. I.

2017-12-01

Several studies on photovoltaic systems focused on how it operates and energy required in operating it. Little attention is paid on its configurations, modeling of mean time to system failure, availability, cost benefit and comparisons of parallel and series-parallel designs. In this research work, four system configurations were studied. Configuration I consists of two sub-components arranged in parallel with 24 V each, configuration II consists of four sub-components arranged logically in parallel with 12 V each, configuration III consists of four sub-components arranged in series-parallel with 8 V each, and configuration IV has six sub-components with 6 V each arranged in series-parallel. Comparative analysis was made using Chapman Kolmogorov's method. The derivation for explicit expression of mean time to system failure, steady state availability and cost benefit analysis were performed, based on the comparison. Ranking method was used to determine the optimal configuration of the systems. The results of analytical and numerical solutions of system availability and mean time to system failure were determined and it was found that configuration I is the optimal configuration.

An exploratory study of organization design configurations in health care delivery organizations.

PubMed

Sheppeck, Mick; Militello, Jack

2014-01-01

Organizations are configurations of variables that support each other to achieve customer satisfaction. Based on Treacy and Wiersema (1995), we predicted the emergence of two configurations, one supporting a product leadership stance and one predicting the customer intimate approach from a set of 73 for profit health care clinics. In addition, we predicted the emergence of a configuration where the scores on most variables were near the mean for each variable. Using cluster analysis and discriminant function analysis, we identified three configurations: one a "master of two" strategy, one "stuck-in-the-middle," and one showing scores well below the mean on most variables. The implications for organization design and manager actions in the health care industry are discussed.

Isolation, identification, and cytotoxicity of a new isobenzofuran derivative from marine Streptomyces sp. W007

NASA Astrophysics Data System (ADS)

Zhang, Hongyu; Xie, Zeping; Lou, Tingting; Jiang, Peng

2016-03-01

A new isobenzofuran derivative ( 1) was isolated from the marine Streptomyces sp. W007 and its structure was determined through extensive spectroscopic analyses, including 1D-NMR, 2D-NMR, and ESI-MS. The absolute configuration of compound 1 was determined by a combination of experimental analyses and comparison with reported data, including biogenetic reasoning, J-coupling analysis, NOESY, and 1H-1HCOSY. Compound 1 exhibited no cytotoxicity against human cells of gastric cancer BGC-823, lung cancer A549, and breast cancer MCF7.

Time-dependent analysis of the mixed-field orientation of molecules without rotational symmetry

NASA Astrophysics Data System (ADS)

Thesing, Linda V.; Küpper, Jochen; González-Férez, Rosario

2017-06-01

We present a theoretical study of the mixed-field orientation of molecules without rotational symmetry. The time-dependent one-dimensional and three-dimensional orientation of a thermal ensemble of 6-chloropyridazine-3-carbonitrile molecules in combined linearly or elliptically polarized laser fields and tilted dc electric fields is computed. The results are in good agreement with recent experimental results of one-dimensional orientation for weak dc electric fields [J. L. Hansen, J. Chem. Phys. 139, 234313 (2013)]. Moreover, they predict that using elliptically polarized laser fields or strong dc fields, three-dimensional orientation is obtained. The field-dressed dynamics of excited rotational states is characterized by highly non-adiabatic effects. We analyze the sources of these non-adiabatic effects and investigate their impact on the mixed-field orientation for different field configurations in mixed-field-orientation experiments.

J2ME and smart phones as platform for a Bluetooth body area network for patient-telemonitoring.

PubMed

Morón, M J; Luque, J R; Botella, A A; Cuberos, E J; Casilari, E; Díaz-Estrella, A

2007-01-01

A prototype of a system based on a Bluetooth Body Area Network (BAN) for continuous and wireless telemonitoring of patients' biosignals is presented. Smart phones and Java (J2ME) have been selected as platform to build a central node in patients' BAN. A midlet running in the smart phone compiles information about patient's location and health status. The midlet encrypts and retransmits it to the server through 802.11 or GPRS/UMTS. Besides when an alerting condition is detected, the midlet generates a MMS and a SMS to be sent to patients' relatives and to physician, respectively. Additionally, the system provides to physicians the possibility of configuring BAN's parameters remotely, from a PC or even a smart phone.

Configuration development study of the X-24C hypersonic research airplane, phase 1

NASA Technical Reports Server (NTRS)

Combs, H. G.

1976-01-01

Four hypersonic research airplane configurations found to be the most cost effective were selected for further refinement. The selection was based on a systematic analysis and evaluation of realistic designs, involving nine different configurations, evolving from three different structural/thermal concepts, coupled with existing rocket and sustainer engines. All configurations were constrained by the mission profiles, research requirements, aerodynamic envelope and maximum launch weight established by NASA.

Parametric Study of Biconic Re-Entry Vehicles

NASA Technical Reports Server (NTRS)

Steele, Bryan; Banks, Daniel W.; Whitmore, Stephen A.

2007-01-01

An optimization based on hypersonic aerodynamic performance and volumetric efficiency was accomplished for a range of biconic configurations. Both axisymmetric and quasi-axisymmetric geometries (bent and flattened) were analyzed. The aerodynamic optimization wag based on hypersonic simple Incidence angle analysis tools. The range of configurations included those suitable for r lunar return trajectory with a lifting aerocapture at Earth and an overall volume that could support a nominal crew. The results yielded five configurations that had acceptable aerodynamic performance and met overall geometry and size limitations

Bounding the Risk of Crew Loss Following Orbital Debris Penetration of the International Space Station at Assembly Stages 1J and 1E

NASA Technical Reports Server (NTRS)

Evans, S.; Lewis, H.; Williamsen, J.; Evans, H.; Bohl, W.; Parker, Nelson (Technical Monitor)

2002-01-01

Orbital debris impacts on the International Space Station occur frequently. To date, none of the impacting particles has been sufficiently large to penetrate manned pressurized volumes. We used the Manned Spacecraft Crew Survivability code to evaluate the risk to crew of penetrations of pressurized modules at two assembly stages: after Flight lJ, when the pressurized elements of Kibo, the Japanese Experiment Module, are present, and after Flight lE, when the European Columbus Module is present. Our code is a Monte Carlo simulation of impacts on the Station that considers several potential event types that could lead to crew loss. Among the statistics tabulated by the program is the probability of death of one or more crew members, expressed as the risk factor, R. This risk factor is dependent on details of crew operations during both ordinary circumstances and decompression emergencies, as well as on details of internal module configurations. We conducted trade studies considering these procedure and configuration details to determine the bounds on R at the 1J and 1E stages in the assembly sequence. Here we compare the R-factor bounds, and procedures and configurations that reduce R at these stages.

Comparative research of redundant strap down inertial navigation system based on different configuration schemes

NASA Astrophysics Data System (ADS)

Yu, Yuting; Cheng, Ming

2018-05-01

Aiming at various configuration scheme and inertial measurement units of Strapdown Inertial Navigation System, selected tetrahedron skew configuration and coaxial orthogonal configuration by nine low cost IMU to build system. Calculation and simulation the performance index, reliability and fault diagnosis ability of the navigation system. Analysis shows that the reliability and reconfiguration scheme of skew configuration is superior to the orthogonal configuration scheme, while the performance index and fault diagnosis ability of the system are similar. The work in this paper provides a strong reference for the selection of engineering applications.

Compact millijoule diode-seeded two-stage fiber master oscillator power amplifier using a multipass and forward pumping scheme.

PubMed

Lai, Po-Yen; Chang, Chun-Lin; Huang, Sheng-Lung; Chen, Shih-Hung

2018-05-01

The multipass scheme for a diode-seeded fiber master oscillator power amplifier with a nanojoule-to-millijoule output energy level at a repetition rate of <100  kHz is numerically analyzed for comparison to an experimental benchmark. For a 6/125 single-mode preamplifier with a small input energy (<1  nJ), there is a significant improvement in the output energy from 0.7% to 80% and 95% of the maximum extractable energy using the double-pass and four-pass schemes, respectively. For a 30/250 large-mode-area power amplifier using the double-pass and forward pumping scheme, the required input energy is decreased from 100 μJ to 18 μJ for millijoule energy extraction with accompanying Stokes waves of less than 10% of the total energy. The system based on the full master oscillator power amplifier configuration with an output energy exceeding millijoule level can be optimally simplified to two stages for commercialization.

Temporal Patterns of Variable Relationships in Person-Oriented Research: Longitudinal Models of Configural Frequency Analysis

ERIC Educational Resources Information Center

von Eye, Alexander; Mun, Eun Young; Bogat, G. Anne

2008-01-01

This article reviews the premises of configural frequency analysis (CFA), including methods of choosing significance tests and base models, as well as protecting [alpha], and discusses why CFA is a useful approach when conducting longitudinal person-oriented research. CFA operates at the manifest variable level. Longitudinal CFA seeks to identify…

Security Criteria for Distributed Systems: Functional Requirements.

DTIC Science & Technology

1995-09-01

Open Company Limited. Ziv , J. and A. Lempel . 1977. A Universal Algorithm for Sequential Data Compression . IEEE Transactions on Information Theory Vol...3, SCF-5 DCF-7. Configurable Cryptographic Algorithms (a) It shall be possible to configure the system such that the data confidentiality functions...use different cryptographic algorithms for different protocols (e.g., mail or interprocess communication data ). (b) The modes of encryption

One joule per Q-switched pulse diode-pumped laser

NASA Technical Reports Server (NTRS)

Holder, Lonnie E.; Kennedy, Chandler; Long, Larry; Dube, George

1992-01-01

Q-switched 1-J output has been achieved from diode-pumped zig-zag Nd:YAG slabs in an oscillator-amplifier configuration. The oscillator was single transverse and longitudinal model. This laser set records for Q-switched energy per pulse, and for average power from a diode-pumped laser. The laser was constructed in a rugged configuration suitable for routine laboratory use.

16 CFR 1203.4 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... solid model in the shape of a human head of sizes A, E, J, M, and O as defined in draft ISO/DIS 6220... configure the helmet for a range of different head sizes. (d) Coronal plane is an anatomical plane... to secure its position on the headform. The mass of the preload ballast is 5 kg (11 lb). (j...

16 CFR 1203.4 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... solid model in the shape of a human head of sizes A, E, J, M, and O as defined in draft ISO/DIS 6220... configure the helmet for a range of different head sizes. (d) Coronal plane is an anatomical plane... to secure its position on the headform. The mass of the preload ballast is 5 kg (11 lb). (j...

Analytical Investigations of Bulk Wave Resonators in the Piezoelectric Thin Film on Gallium-Arsenide Configuration.

DTIC Science & Technology

1987-07-28

OPPICE SYMBOL (Inedu @ Ame Cadep Kevin J. Malloy 202-767-4931 NE DO FORM 1473, 83 APR EDITION OF I JAN 73 S OBSOLETE. Unclassified . ’ J P...Sitnce thle calculated Q is a very cuadshldbhiertnteatalQsbcuete rapdlyvaringfuntioi o th waer hicnes, clcuatins material Q and thle Q due to radiation

Structural Configuration Systems Analysis for Advanced Aircraft Fuselage Concepts

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek; Welstead, Jason R.; Quinlan, Jesse R.; Guynn, Mark D.

2016-01-01

Structural configuration analysis of an advanced aircraft fuselage concept is investigated. This concept is characterized by a double-bubble section fuselage with rear mounted engines. Based on lessons learned from structural systems analysis of unconventional aircraft, high-fidelity finite-element models (FEM) are developed for evaluating structural performance of three double-bubble section configurations. Structural sizing and stress analysis are applied for design improvement and weight reduction. Among the three double-bubble configurations, the double-D cross-section fuselage design was found to have a relatively lower structural weight. The structural FEM weights of these three double-bubble fuselage section concepts are also compared with several cylindrical fuselage models. Since these fuselage concepts are different in size, shape and material, the fuselage structural FEM weights are normalized by the corresponding passenger floor area for a relative comparison. This structural systems analysis indicates that an advanced composite double-D section fuselage may have a relative structural weight ratio advantage over a conventional aluminum fuselage. Ten commercial and conceptual aircraft fuselage structural weight estimates, which are empirically derived from the corresponding maximum takeoff gross weight, are also presented and compared with the FEM- based estimates for possible correlation. A conceptual full vehicle FEM model with a double-D fuselage is also developed for preliminary structural analysis and weight estimation.

Semi-stochastic full configuration interaction quantum Monte Carlo

NASA Astrophysics Data System (ADS)

Holmes, Adam; Petruzielo, Frank; Khadilkar, Mihir; Changlani, Hitesh; Nightingale, M. P.; Umrigar, C. J.

2012-02-01

In the recently proposed full configuration interaction quantum Monte Carlo (FCIQMC) [1,2], the ground state is projected out stochastically, using a population of walkers each of which represents a basis state in the Hilbert space spanned by Slater determinants. The infamous fermion sign problem manifests itself in the fact that walkers of either sign can be spawned on a given determinant. We propose an improvement on this method in the form of a hybrid stochastic/deterministic technique, which we expect will improve the efficiency of the algorithm by ameliorating the sign problem. We test the method on atoms and molecules, e.g., carbon, carbon dimer, N2 molecule, and stretched N2. [4pt] [1] Fermion Monte Carlo without fixed nodes: a Game of Life, death and annihilation in Slater Determinant space. George Booth, Alex Thom, Ali Alavi. J Chem Phys 131, 050106, (2009).[0pt] [2] Survival of the fittest: Accelerating convergence in full configuration-interaction quantum Monte Carlo. Deidre Cleland, George Booth, and Ali Alavi. J Chem Phys 132, 041103 (2010).

Daniel J. Schell | NREL

Science.gov Websites

processing High solids biomass conversion Fermentation process development Separation processes Techno ; Bioresour. Technol. (2010) "An economic comparison of different fermentation configurations to convert

A study of gradient strengthening based on a finite-deformation gradient crystal-plasticity model

NASA Astrophysics Data System (ADS)

Pouriayevali, Habib; Xu, Bai-Xiang

2017-11-01

A comprehensive study on a finite-deformation gradient crystal-plasticity model which has been derived based on Gurtin's framework (Int J Plast 24:702-725, 2008) is carried out here. This systematic investigation on the different roles of governing components of the model represents the strength of this framework in the prediction of a wide range of hardening behaviors as well as rate-dependent and scale-variation responses in a single crystal. The model is represented in the reference configuration for the purpose of numerical implementation and then implemented in the FEM software ABAQUS via a user-defined subroutine (UEL). Furthermore, a function of accumulation rates of dislocations is employed and viewed as a measure of formation of short-range interactions. Our simulation results reveal that the dissipative gradient strengthening can be identified as a source of isotropic-hardening behavior, which may represent the effect of irrecoverable work introduced by Gurtin and Ohno (J Mech Phys Solids 59:320-343, 2011). Here, the variation of size dependency at different magnitude of a rate-sensitivity parameter is also discussed. Moreover, an observation of effect of a distinctive feature in the model which explains the effect of distortion of crystal lattice in the reference configuration is reported in this study for the first time. In addition, plastic flows in predefined slip systems and expansion of accumulation of GNDs are distinctly observed in varying scales and under different loading conditions.

Lifetimes of 3s3p2 J=12,52 levels in Au66+ and Br22+

NASA Astrophysics Data System (ADS)

Beck, Donald R.; Norquist, Peggy L.

2000-04-01

Relativistic configuration-interaction length and velocity lifetimes have been obtained for 3s3p2 J=1/2, 5/2 levels in Au66+ and Br22+. Results from the two gauges agree well, and we have moderately improved earlier multiconfigurational Dirac-Fock results, as compared to experiment. However, there remains a discrepancy for the Au66+ J=5/2 lifetime, which may be due to satellite spectra associated with 5g and other spectator electrons.

Ultra-High Sensitive Magnetoelectric Nanocomposites Current Sensors

DTIC Science & Technology

2011-03-30

mass made from PZT ceramic . For the 3rd and 4th configuration, 1 g and 2 g “active” nickel (Ni) tip masses were utilized. Figure VIII.1(a) shows the...Trilayer Magnetoelectric Composites with Partial Texturing ”, J. Mater. Sci., (2009) DOI 10.1007/s10853-009-3744-9. 6. R. A. Islam, and S. Priya, “Effect of...of Cofired Trilayer Magnetoelectric Composites with Partial Texturing ”, J. Mater. Sci., (2009) (accepted). 10. C.-S. Park, C.-W. Ahn, J. Ryu, W.-H

Factors controlling volume errors through 2D gully erosion assessment: guidelines for optimal survey design

NASA Astrophysics Data System (ADS)

Castillo, Carlos; Pérez, Rafael

2017-04-01

The assessment of gully erosion volumes is essential for the quantification of soil losses derived from this relevant degradation process. Traditionally, 2D and 3D approaches has been applied for this purpose (Casalí et al., 2006). Although innovative 3D approaches have recently been proposed for gully volume quantification, a renewed interest can be found in literature regarding the useful information that cross-section analysis still provides in gully erosion research. Moreover, the application of methods based on 2D approaches can be the most cost-effective approach in many situations such as preliminary studies with low accuracy requirements or surveys under time or budget constraints. The main aim of this work is to examine the key factors controlling volume error variability in 2D gully assessment by means of a stochastic experiment involving a Monte Carlo analysis over synthetic gully profiles in order to 1) contribute to a better understanding of the drivers and magnitude of gully erosion 2D-surveys uncertainty and 2) provide guidelines for optimal survey designs. Owing to the stochastic properties of error generation in 2D volume assessment, a statistical approach was followed to generate a large and significant set of gully reach configurations to evaluate quantitatively the influence of the main factors controlling the uncertainty of the volume assessment. For this purpose, a simulation algorithm in Matlab® code was written, involving the following stages: - Generation of synthetic gully area profiles with different degrees of complexity (characterized by the cross-section variability) - Simulation of field measurements characterised by a survey intensity and the precision of the measurement method - Quantification of the volume error uncertainty as a function of the key factors In this communication we will present the relationships between volume error and the studied factors and propose guidelines for 2D field surveys based on the minimal survey densities required to achieve a certain accuracy given the cross-sectional variability of a gully and the measurement method applied. References Casali, J., Loizu, J., Campo, M.A., De Santisteban, L.M., Alvarez-Mozos, J., 2006. Accuracy of methods for field assessment of rill and ephemeral gully erosion. Catena 67, 128-138. doi:10.1016/j.catena.2006.03.005

Structural analysis for preliminary design of High Speed Civil Transport (HSCT)

NASA Technical Reports Server (NTRS)

Bhatia, Kumar G.

1992-01-01

In the preliminary design environment, there is a need for quick evaluation of configuration and material concepts. The simplified beam representations used in the subsonic, high aspect ratio wing platform are not applicable for low aspect ratio configurations typical of supersonic transports. There is a requirement to develop methods for efficient generation of structural arrangement and finite element representation to support multidisciplinary analysis and optimization. In addition, empirical data bases required to validate prediction methods need to be improved for high speed civil transport (HSCT) type configurations.

PAN AIR - A Computer Program for Predicting Subsonic or Supersonic Linear Potential Flows about Arbitrary Configurations Using a Higher Order Panel Method. Volume I. Theory Document (Version 1.0)

DTIC Science & Technology

1980-04-15

superinclined panel J.12-12 J.20 Transformation to (s,t) variables and region of integration J.12-13 J.21 Numbering of edges of ’n Hh J.12-13 J.22 A region... JB . 4.12d((C-x) 2+(n-y)2+(ý-z)2)i) (8.4.12) we have • (P) ij 0 (8.4.13) if i+j is even, and i+j > 0. Let us now consider the velocity OD Pij I1 4...came from, since we did not arrive at A through a rigorous procedure. Recall that we claim that AT I [CO] r [Co] o n’o I~~ I, )T-- hh )1T (E.3.16a

Cloud BioLinux: pre-configured and on-demand bioinformatics computing for the genomics community.

PubMed

Krampis, Konstantinos; Booth, Tim; Chapman, Brad; Tiwari, Bela; Bicak, Mesude; Field, Dawn; Nelson, Karen E

2012-03-19

A steep drop in the cost of next-generation sequencing during recent years has made the technology affordable to the majority of researchers, but downstream bioinformatic analysis still poses a resource bottleneck for smaller laboratories and institutes that do not have access to substantial computational resources. Sequencing instruments are typically bundled with only the minimal processing and storage capacity required for data capture during sequencing runs. Given the scale of sequence datasets, scientific value cannot be obtained from acquiring a sequencer unless it is accompanied by an equal investment in informatics infrastructure. Cloud BioLinux is a publicly accessible Virtual Machine (VM) that enables scientists to quickly provision on-demand infrastructures for high-performance bioinformatics computing using cloud platforms. Users have instant access to a range of pre-configured command line and graphical software applications, including a full-featured desktop interface, documentation and over 135 bioinformatics packages for applications including sequence alignment, clustering, assembly, display, editing, and phylogeny. Each tool's functionality is fully described in the documentation directly accessible from the graphical interface of the VM. Besides the Amazon EC2 cloud, we have started instances of Cloud BioLinux on a private Eucalyptus cloud installed at the J. Craig Venter Institute, and demonstrated access to the bioinformatic tools interface through a remote connection to EC2 instances from a local desktop computer. Documentation for using Cloud BioLinux on EC2 is available from our project website, while a Eucalyptus cloud image and VirtualBox Appliance is also publicly available for download and use by researchers with access to private clouds. Cloud BioLinux provides a platform for developing bioinformatics infrastructures on the cloud. An automated and configurable process builds Virtual Machines, allowing the development of highly customized versions from a shared code base. This shared community toolkit enables application specific analysis platforms on the cloud by minimizing the effort required to prepare and maintain them.

Cloud BioLinux: pre-configured and on-demand bioinformatics computing for the genomics community

PubMed Central

2012-01-01

Background A steep drop in the cost of next-generation sequencing during recent years has made the technology affordable to the majority of researchers, but downstream bioinformatic analysis still poses a resource bottleneck for smaller laboratories and institutes that do not have access to substantial computational resources. Sequencing instruments are typically bundled with only the minimal processing and storage capacity required for data capture during sequencing runs. Given the scale of sequence datasets, scientific value cannot be obtained from acquiring a sequencer unless it is accompanied by an equal investment in informatics infrastructure. Results Cloud BioLinux is a publicly accessible Virtual Machine (VM) that enables scientists to quickly provision on-demand infrastructures for high-performance bioinformatics computing using cloud platforms. Users have instant access to a range of pre-configured command line and graphical software applications, including a full-featured desktop interface, documentation and over 135 bioinformatics packages for applications including sequence alignment, clustering, assembly, display, editing, and phylogeny. Each tool's functionality is fully described in the documentation directly accessible from the graphical interface of the VM. Besides the Amazon EC2 cloud, we have started instances of Cloud BioLinux on a private Eucalyptus cloud installed at the J. Craig Venter Institute, and demonstrated access to the bioinformatic tools interface through a remote connection to EC2 instances from a local desktop computer. Documentation for using Cloud BioLinux on EC2 is available from our project website, while a Eucalyptus cloud image and VirtualBox Appliance is also publicly available for download and use by researchers with access to private clouds. Conclusions Cloud BioLinux provides a platform for developing bioinformatics infrastructures on the cloud. An automated and configurable process builds Virtual Machines, allowing the development of highly customized versions from a shared code base. This shared community toolkit enables application specific analysis platforms on the cloud by minimizing the effort required to prepare and maintain them. PMID:22429538

Longitudinal aerodynamic characteristics of a large scale model with a swept wing and augmented jet flap in ground effect

NASA Technical Reports Server (NTRS)

Falarski, M. D.; Koenig, D. G.

1972-01-01

The investigation of the in-ground-effect, longitudinal aerodynamic characteristics of a large scale swept augmentor wing model is presented, using 40 x 80 ft wind tunnel. The investigation was conducted at three ground heights; h/c equals 2.01, 1.61, and 1.34. The induced effect of underwing nacelles, was studied with two powered nacelle configurations. One configuration used four JT-15D turbofans while the other used two J-85 turbojet engines. Two conical nozzles on each J-85 were used to deflect the thrust at angles from 0 to 120 deg. Tests were also performed without nacelles to allow comparison with previous data from ground effect.

Generation of broadband laser by high-frequency bulk phase modulator with multipass configuration.

PubMed

Zhang, Peng; Jiang, Youen; Zhou, Shenlei; Fan, Wei; Li, Xuechun

2014-12-10

A new technique is presented for obtaining a large broadband nanosecond-laser pulse. This technique is based on multipass phase modulation of a single-frequency nanosecond-laser pulse from the integrated front-end source, and it is able to shape the temporal profile of the pulse arbitrarily, making this approach attractive for high-energy-density physical experiments in current laser fusion facilities. Two kinds of cavity configuration for multipass modulation are proposed, and the performances of both of them are discussed theoretically in detail for the first time to our knowledge. Simulation results show that the bandwidth of the generated laser pulse by this approach can achieve more than 100 nm in principle if adjustment accuracy of the time interval between contiguous passes is controlled within 0.1% of a microwave period. In our preliminary experiment, a 2 ns laser pulse with 1.35-nm bandwidth in 1053 nm is produced via this technique, which agrees well with the theoretical result. Owing to an all-solid-state structure, the energy of the pulse achieves 25 μJ. In the future, with energy compensation and spectrum filtering, this technique is expected to generate a nanosecond-laser pulse of 3 nm or above bandwidth with energy of about 100 μJ.

On the estimation of jet-induced fountain lift and additional suckdown in hover for two-jet configurations

NASA Technical Reports Server (NTRS)

Kuhn, Richard E.; Bellavia, David C.; Corsiglia, Victor R.; Wardwell, Douglas A.

1991-01-01

Currently available methods for estimating the net suckdown induced on jet V/STOL aircraft hovering in ground effect are based on a correlation of available force data and are, therefore, limited to configurations similar to those in the data base. Experience with some of these configurations has shown that both the fountain lift and additional suckdown are overestimated but these effects cancel each other for configurations within the data base. For other configurations, these effects may not cancel and the net suckdown could be grossly overestimated or underestimated. Also, present methods do not include the prediction of the pitching moments associated with the suckdown induced in ground effect. An attempt to develop a more logically based method for estimating the fountain lift and suckdown based on the jet-induced pressures is initiated. The analysis is based primarily on the data from a related family of three two-jet configurations (all using the same jet spacing) and limited data from two other two-jet configurations. The current status of the method, which includes expressions for estimating the maximum pressure induced in the fountain regions, and the sizes of the fountain and suckdown regions is presented. Correlating factors are developed to be used with these areas and pressures to estimate the fountain lift, the suckdown, and the related pitching moment increments.

Mixed-Fidelity Approach for Design of Low-Boom Supersonic Aircraft

NASA Technical Reports Server (NTRS)

Li, Wu; Shields, Elwood; Geiselhart, Karl

2011-01-01

This paper documents a mixed-fidelity approach for the design of low-boom supersonic aircraft with a focus on fuselage shaping.A low-boom configuration that is based on low-fidelity analysis is used as the baseline. The fuselage shape is modified iteratively to obtain a configuration with an equivalent-area distribution derived from computational fluid dynamics analysis that attempts to match a predetermined low-boom target area distribution and also yields a low-boom ground signature. The ground signature of the final configuration is calculated by using a state-of-the-art computational-fluid-dynamics-based boom analysis method that generates accurate midfield pressure distributions for propagation to the ground with ray tracing. The ground signature that is propagated from a midfield pressure distribution has a shaped ramp front, which is similar to the ground signature that is propagated from the computational fluid dynamics equivalent-area distribution. This result supports the validity of low-boom supersonic configuration design by matching a low-boom equivalent-area target, which is easier to accomplish than matching a low-boom midfield pressure target.

Effect of gadolinium incorporation on the structure and luminescence properties of niobium-based materials

NASA Astrophysics Data System (ADS)

Resende Oliveira, Lidia; Bonamin Moscardini, Susane; Ferreira Molina, Eduardo; José Nassar, Eduardo; Verelst, Marc; Alonso Rocha, Lucas

2018-06-01

In this work, we have investigated how the concentration of Gd3+ ions affects the structural and luminescent properties of niobium oxide-based matrices doped with Eu3+ ions obtained by the adapted non-hydrolytic sol–gel route. X-ray diffractograms revealed that increasing the concentration of Gd3+ ions favored the onset of the Gd2O3 structure decreasing the GdNbO4 phase. The excitation spectra (λ em = 613 nm) presented bands corresponding to the 7F0 → 5LJ transitions (L = D, G, and L, where J = 0–7), attributed to the Eu3+ ions, and a broad band at 270 nm, assigned to the charge transfer of the {{{{NbO}}}4}3- group. The emission spectra contained bands refer to the 5D0 → 7FJ internal configuration transitions (J = 0, 1, 2, 3, and 4). Finally, the CIE chromaticity coordinates met the standard for the color red established by the National Television Standard Committee (NTSC).

Modeling analysis of pulsed magnetization process of magnetic core based on inverse Jiles-Atherton model

NASA Astrophysics Data System (ADS)

Liu, Yi; Zhang, He; Liu, Siwei; Lin, Fuchang

2018-05-01

The J-A (Jiles-Atherton) model is widely used to describe the magnetization characteristics of magnetic cores in a low-frequency alternating field. However, this model is deficient in the quantitative analysis of the eddy current loss and residual loss in a high-frequency magnetic field. Based on the decomposition of magnetization intensity, an inverse J-A model is established which uses magnetic flux density B as an input variable. Static and dynamic core losses under high frequency excitation are separated based on the inverse J-A model. Optimized parameters of the inverse J-A model are obtained based on particle swarm optimization. The platform for the pulsed magnetization characteristic test is designed and constructed. The hysteresis curves of ferrite and Fe-based nanocrystalline cores at high magnetization rates are measured. The simulated and measured hysteresis curves are presented and compared. It is found that the inverse J-A model can be used to describe the magnetization characteristics at high magnetization rates and to separate the static loss and dynamic loss accurately.

Cation coordination reactions on nanocrystals: surface/interface, doping control and advanced photocatalysis applications (Conference Presentation)

NASA Astrophysics Data System (ADS)

Zhang, Jiatao

2016-10-01

Abstract: Including the shape and size effect, the controllable doping, hetero-composite and surface/interface are the prerequisite of colloidal nanocrystals for exploring their optoelectronic properties, such as fluorescence, plasmon-exciton coupling, efficient electron/hole separation, and enhanced photocatalysis applications. By controlling soft acid-base coordination reactions between cation molecular complexes and colloidal nanocrystals, we showed that chemical thermodynamics could drive nanoscale monocrystalline growth of the semiconductor shell on metal nano-substrates and the substitutional heterovalent doping in semiconductor nanocrystals. We have demonstrated evolution of relative position of Au and II-VI semiconductor in Au-Semi from symmetric to asymmetric configuration, different phosphines initiated morphology engineering, oriented attachment of quantum dots into micrometer nanosheets with synergistic control of surface/interface and doing, which can further lead to fine tuning of plasmon-exciton coupling. Therefore, different hydrogen photocatalytic performance, Plasmon enhanced photocatalysis properties have been achieved further which lead to the fine tuning of plasmon-exciton coupling. Substitutional heterovalent doping here enables the tailoring of optical, electronic properties and photocatalysis applications of semiconductor nanocrystals because of electronic impurities (p-, n-type doping) control. References: (1) J. Gui, J. Zhang*, et al. Angew. Chem. Int. Ed. 2015, 54, 3683. (2) Q. Zhao, J. Zhang*, etc., Adv. Mater. 2014, 26, 1387. (3) J. Liu, Q. Zhao, S. G. Wang*, J. Zhang*, etc., Adv. Mater. 2015, 27-2753-2761. (4) H. Qian, J. Zhang*, etc., NPG Asia Mater. (2015) 7, e152. (5) M. Ji, M. Xu, etc., J. Zhang*, Adv. Mater. 2016, in proof. (6) S. Yu, J. T. Zhang, Y. Tang, M. Ouyang*, Nano Lett. 2015, 15, 6282-6288. (7) J. Zhang, Y. Tang, K. Lee and M. Ouyang*, Science 2010, 327, 1634. (8) J. Zhang, Y. Tang, K. Lee, M. Ouyang*, Nature 2010, 466, 91.

Observations and light curve solutions of three ultrashort-period W UMa binaries

NASA Astrophysics Data System (ADS)

Kjurkchieva, Diana P.; Michel, Raul; Popov, Velimir A.; Deras, Dan

2018-07-01

Photometric observations in V, Rc and Ic bands of the ultrashort-period W UMa binaries 1SWASP J044132.96+440613.7, 1SWASP J052926.88+461147.5 and NSVS 2175434 are presented. The results from the modeling and analysis of our observations reveal that: (i) All targets undergo total eclipses and their photometric mass ratios should be accepted with confidence; (ii) All stellar components are late-type dwarfs; (iii) The temperature difference of target components does not exceed 150 K; (iv) All targets have overcontact configurations with fill-out factor around 0.24; (v) The orbit of NSVS 2175434 is slightly eccentric which is unusual for such an ultrashort-period binary; (vi) The orbital periods of all targets were improved. Masses, radii and luminosities of the stellar components were estimated by the empirical relation "period, orbital axis" for short- and ultrashort-period binaries.

Sensitivity of tropical convection in cloud-resolving WRF simulations to model physics and forcing procedures

NASA Astrophysics Data System (ADS)

Endo, S.; Lin, W.; Jackson, R. C.; Collis, S. M.; Vogelmann, A. M.; Wang, D.; Oue, M.; Kollias, P.

2017-12-01

Tropical convection is one of the main drivers of the climate system and recognized as a major source of uncertainty in climate models. High-resolution modeling is performed with a focus on the deep convection cases during the active monsoon period of the TWP-ICE field campaign to explore ways to improve the fidelity of convection permitting tropical simulations. Cloud resolving model (CRM) simulations are performed with WRF modified to apply flexible configurations for LES/CRM simulations. We have enhanced the capability of the forcing module to test different implementations of large-scale vertical advective forcing, including a function for optional use of large-scale thermodynamic profiles and a function for the condensate advection. The baseline 3D CRM configurations are, following Fridlind et al. (2012), driven by observationally-constrained ARM forcing and tested with diagnosed surface fluxes and fixed sea-surface temperature and prescribed aerosol size distributions. After the spin-up period, the simulations follow the observed precipitation peaks associated with the passages of precipitation systems. Preliminary analysis shows that the simulation is generally not sensitive to the treatment of the large-scale vertical advection of heat and moisture, while more noticeable changes in the peak precipitation rate are produced when thermodynamic profiles above the boundary layer were nudged to the reference profiles from the forcing dataset. The presentation will explore comparisons with observationally-based metrics associated with convective characteristics and examine the model performance with a focus on model physics, doubly-periodic vs. nested configurations, and different forcing procedures/sources. A radar simulator will be used to understand possible uncertainties in radar-based retrievals of convection properties. Fridlind, A. M., et al. (2012), A comparison of TWP-ICE observational data with cloud-resolving model results, J. Geophys. Res., 117, D05204, doi:10.1029/2011JD016595.

Orion Orbit Control Design and Analysis

NASA Technical Reports Server (NTRS)

Jackson, Mark; Gonzalez, Rodolfo; Sims, Christopher

2007-01-01

The analysis of candidate thruster configurations for the Crew Exploration Vehicle (CEV) is presented. Six candidate configurations were considered for the prime contractor baseline design. The analysis included analytical assessments of control authority, control precision, efficiency and robustness, as well as simulation assessments of control performance. The principles used in the analytic assessments of controllability, robustness and fuel performance are covered and results provided for the configurations assessed. Simulation analysis was conducted using a pulse width modulated, 6 DOF reaction system control law with a simplex-based thruster selection algorithm. Control laws were automatically derived from hardware configuration parameters including thruster locations, directions, magnitude and specific impulse, as well as vehicle mass properties. This parameterized controller allowed rapid assessment of multiple candidate layouts. Simulation results are presented for final phase rendezvous and docking, as well as low lunar orbit attitude hold. Finally, on-going analysis to consider alternate Service Module designs and to assess the pilot-ability of the baseline design are discussed to provide a status of orbit control design work to date.

Miniature Tunable Laser Spectrometer for Detection of a Trace Gas

NASA Technical Reports Server (NTRS)

Christensen, Lance E. (Inventor)

2017-01-01

An open-path laser spectrometer (OPLS) for measuring a concentration of a trace gas, the OPLS including an open-path multi-pass analysis region including a first mirror, a second mirror at a distance and orientation from the first mirror, and a support structure for locating the mirrors, a laser coupled to the analysis region and configured to emit light of a wavelength range and to enable a plurality of reflections of the emitted light between the mirrors, a detector coupled to the analysis region and configured to detect a portion of the emitted light impinging on the detector and to generate a corresponding signal, and an electronic system coupled to the laser and the detector, and configured to adjust the wavelength range of the emitted light from the laser based on the generated signal, and to measure the concentration of the trace gas based on the generated signal.

Conceptual design studies for surface infrastructure

NASA Technical Reports Server (NTRS)

Bufkin, Ann L.; Jones, William R., II

1986-01-01

The utimate design of a manned Mars base will be the result of considerable engineering analysis and many trade studies to optimize the configuration. Many options and scenarios are available and all need to be considered at this time. Initial base elements, two base configuration concepts, internal space architectural concerns, and two base set-up scenarios are discussed. There are many variables as well as many unknowns to be reckoned with before people set foot on the red planet.

100μJ-level single frequency linearly-polarized nanosecond pulsed laser at 775 nm (Conference Presentation)

NASA Astrophysics Data System (ADS)

Shi, Wei; Fang, Qiang; Fan, Jingli; Cui, Xuelong; Zhang, Zhuo; Li, Jinhui; Zhou, Guoqing

2017-02-01

We report a single frequency, linearly polarized, near diffraction-limited, pulsed laser source at 775 nm by frequency doubling a single frequency nanosecond pulsed all fiber based master oscillator-power amplifier, seeded by a fiber coupled semiconductor DFB laser diode at 1550 nm. The laser diode was driven by a pulsed laser driver to generate 5 ns laser pulses at 260 Hz repetition rate with 50 pJ pulse energy. The pulse energy was boosted to 200 μJ using two stages of core-pumped fiber amplifiers and two stages of cladding-pumped fiber amplifiers. The multi-stage synchronous pulse pumping technique was adopted in the four stages of fiber amplifiers to mitigate the ASE. The frequency doubling is implemented in a single pass configuration using a periodically poled lithium niobate (PPLN) crystal. The crystal is 3 mm long, 1.4 mm wide, 1 mm thick, with a 19.36 μm domain period chosen for quasi-phase matching at 33°C. It was AR coated at both 1550 nm and 775 nm. The maximum pulse energy of 97 μJ was achieved when 189 μJ fundamental laser was launched. The corresponding conversion efficiency is about 51.3%. The pulse duration was measured to be 4.8 ns. So the peak power of the generated 775 nm laser pulses reached 20 kW. To the best of our knowledge, this is the first demonstration of a 100 μJ-level, tens of kilowatts-peak-power-level single frequency linearly polarized 775 nm laser based on the frequency doubling of the fiber lasers.

Predicted facies, sedimentary structures and potential resources of Jurassic petroleum complex in S-E sWestern Siberia (based on well logging data)

NASA Astrophysics Data System (ADS)

Prakojo, F.; Lobova, G.; Abramova, R.

2015-11-01

This paper is devoted to the current problem in petroleum geology and geophysics- prediction of facies sediments for further evaluation of productive layers. Applying the acoustic method and the characterizing sedimentary structure for each coastal-marine-delta type was determined. The summary of sedimentary structure characteristics and reservoir properties (porosity and permeability) of typical facies were described. Logging models SP, EL and GR (configuration, curve range) in interpreting geophysical data for each litho-facies were identified. According to geophysical characteristics these sediments can be classified as coastal-marine-delta. Prediction models for potential Jurassic oil-gas bearing complexes (horizon J11) in one S-E Western Siberian deposit were conducted. Comparing forecasting to actual testing data of layer J11 showed that the prediction is about 85%.

National law enforcement telecommunications network

NASA Technical Reports Server (NTRS)

Reilly, N. B.; Garrison, G. W.; Sohn, R. L.; Gallop, D. L.; Goldstein, B. L.

1975-01-01

Alternative approaches are analyzed to a National Law Enforcement Telecommunications Network (NALECOM) designed to service all state-to-state and state-to-national criminal justice communications traffic needs in the United States. Network topology options were analyzed, and equipment and personnel requirements for each option were defined in accordance with NALECOM functional specifications and design guidelines. Evaluation criteria were developed and applied to each of the options leading to specific conclusions. Detailed treatments of methods for determining traffic requirements, communication line costs, switcher configurations and costs, microwave costs, satellite system configurations and costs, facilities, operations and engineering costs, network delay analysis and network availability analysis are presented. It is concluded that a single regional switcher configuration is the optimum choice based on cost and technical factors. A two-region configuration is competitive. Multiple-region configurations are less competitive due to increasing costs without attending benefits.

Generalized approximate spin projection calculations of effective exchange integrals of the CaMn4O5 cluster in the S1 and S3 states of the oxygen evolving complex of photosystem II.

PubMed

Isobe, H; Shoji, M; Yamanaka, S; Mino, H; Umena, Y; Kawakami, K; Kamiya, N; Shen, J-R; Yamaguchi, K

2014-06-28

Full geometry optimizations followed by the vibrational analysis were performed for eight spin configurations of the CaMn4O4X(H2O)3Y (X = O, OH; Y = H2O, OH) cluster in the S1 and S3 states of the oxygen evolution complex (OEC) of photosystem II (PSII). The energy gaps among these configurations obtained by vertical, adiabatic and adiabatic plus zero-point-energy (ZPE) correction procedures have been used for computation of the effective exchange integrals (J) in the spin Hamiltonian model. The J values are calculated by the (1) analytical method and the (2) generalized approximate spin projection (AP) method that eliminates the spin contamination errors of UB3LYP solutions. Using J values derived from these methods, exact diagonalization of the spin Hamiltonian matrix was carried out, yielding excitation energies and spin densities of the ground and lower-excited states of the cluster. The obtained results for the right (R)- and left (L)-opened structures in the S1 and S3 states are found to be consistent with available optical and magnetic experimental results. Implications of the computational results are discussed in relation to (a) the necessity of the exact diagonalization for computations of reliable energy levels, (b) magneto-structural correlations in the CaMn4O5 cluster of the OEC of PSII, (c) structural symmetry breaking in the S1 and S3 states, and (d) the right- and left-handed scenarios for the O-O bond formation for water oxidation.

Convective thermal fluxes in unsteady non-homogeneous flows generating complex three dimensional vorticity patterns

NASA Astrophysics Data System (ADS)

Tellez Alvarez, Jackson David; Redondo, Jose Manuel; Sanchez, Jesu Mary

2016-04-01

The improvements in experimental methods and high resolution image analysis are nowadays able to detect subtle changes in the structure of the turbulence over a wide range of temporal and spatial scales [1], we compare the scaling shown by different mixing fronts driven by buoyancy that form convective driven mixing. We use PIV and density front tracking in several experimental configurations akin to geophysical overturning [2, 3]. We parametrize the role of unstable stratification by means of the Rayleigh and Atwood numbers and compare the scaling and the multifractal structure functions of the different markers used to visualize the non-homogeneous. Both reactive and passive scalar tracers are used to investigate the mixing structure and the intermittency of the flow. Different initial conditions are compared and the mixing efficiency of the overall turbulent process is evaluated [4 - 6]. Diffusion is measured in the transition from a homogeneous linearly stratified fluid to a cellular or layered structure by means of Thermoelectric generated heating and cooling [2, 4]. Patterns arise by setting up a convective flow generated by a buoyant heat flux either in the base or in a side wall of the convective enclosure [1, 6]. The experiments described here investigate high Prandtl number mixing using brine or sugar solutions and fresh water in order to form a density interface and low Prandtl number mixing with only temperature gradients [7]. The set of dimensionless parameters define conditions of numeric and small scale laboratory modeling of environmental flows. Fields of velocity, density and their gradients were computed and visualized [8, 9]. When convective heating and cooling takes place the combination of internal waves and buoyant turbulence is much more complicated if the Rayleigh and Reynolds numbers are high in order to study entrainment and mixing. The experiments described here investigate high Prandtl number mixing using salt or sugar solutions and fresh water in order to form density interfaces. The Reynolds number can be reduced adding Glicerine the set of dimensionless parameters define different conditions of both numeric and small scale laboratory applied often in modeling environmental flows. Fields of velocity, density and their gradients are computed using advanced visualization [8 9]. Visualizations are performed by PIV, Particle tracking and shadowgraph. When convective heating and cooling takes place the patterns depend on the parameter space region of the initial conditions We also map the different transitions between two and three dimensional convection in an enclosure with several complex driven flows. The size of the water tank is of 0.2 x 0.2 x 0.1 m and the heat sources or sinks can be regulated both in power and sign [2-4]. The thermal convective driven flows are generated by Seebeck and Peltier effects in 4 wall extended positions of 0.05 x 0.05 cm each. The parameter range of convective cell array varies strongly with the Topology of the boundary conditions. At present side heat fluxes are considered and estimated as a function of Rayleigh, Peclet and Nusselt numbers, [4-6] The evolution of the mixing fronts are compared and the topological characteristics of the merging of plumes and jets in different configurations presenting detailed comparison of the evolution of RM and RT, Jets and Plumes in overall mixing. The relation between structure functions, fractal analysis and spectral analysis can be very useful to determine the evolution of scales. Experimental and numerical results on the advance of a mixing or non-mixing front occurring at a density interface due to body forces [12] can be compared with the convective fronts. The evolution of the turbulent mixing layer and its complex configuration is studied taking into account the dependence on the initial modes at the early stages, Self-similar information [13]. Spectral and Fractal analysis on the images seems very useful in order to estimate dominant mixing structures as well as the basic instabilities than drive the turbulent direct and inverse cascades [12]. References [1] Mahjoub O.B.; Redondo J.M.; and Babiano A. (2000). Hyerarchy flux in nonhomogeneous flows in turbulent diffusion in the environment Eds. Redondo J.M. and Babiano A. 249-260. [2] Redondo J.M. (1992). Termodinámica de los procesos irreversibles, efectos termoeléctricos. Rev. Termoelectricidad2, 16-29. AIT. Pamplona. [3] Dalziel, S. B. (1994). Perturbations and coherent flow in Rayleigh-Taylor instability in 4th International Workshop on the Physics of Compressible Turbulent Mixing, ed. P. F. Linden, D. L. Youngs, & S. B. Dalziel; 32-41. [4] Redondo J.M.; Sanchez J.M.; Pascual I.; Noriega, G.F. (1995). Thermoelectric regulation for electric cabinets: XVI International Conference in Thermoelectrics, 02-G20. Ed. V. Vedernikov. 456-468. St. Petersburg, Russia. [5] Mahjoub, O.B; Redondo J.M.; Babiano A. (1998).Structure functions in complex flows: Applied Scientific Research. 59, 299-313. Kluwer. [6] Matulka A.; Redondo J. M.; and Carrillo A. (2008). Experiments in stratified and rotating decaying 2D flows, Il Nuovo Cimento 31, 5-6, 757-770. 2008. [7] Redondo, J.M.; Tellez, J; Sotillos, L.; Gonzalez-Nieto, Pilar L.; Sanchez, J.M.; Furmanek P.,; Diez M (2014). Complex Convective Thermal Fluxes and Vorticity Structure: Geophysical Research Abstracts Vol. 17, EGU2015-14773, 2015 - EGU General Assembly 2015. [8] Nicolleau, F.C.G.A.; Cambon, C.; Redondo, J.M.; Vassilicos, J.C.; Reeks, M.; Nowakowski, A.F. (Eds.) (2012). New Approaches in Modeling Multiphase Flows and Dispersion in Turbulence, Fractal Methods and Synthetic Turbulence: ERCOFTAC Series. [9] Redondo J. M.; Sanchez M. A.; and Cantalapiedra I. R. (1995). Turbulent Mechanisms in Stratified Flows, Dynamics of Atmospheres and Oceans, 23, 454-462. [10] Matulka A.; Redondo J.M.; and Carrillo A. (2008) Experiments in stratified and rotating decaying 2D flows. II Nuovo Cimento 31, 5-6, 757-770. 2008. [11] Fraunie P., Berreba S. Chashechkin Yu.D., Velasco D. and Redondo J.M. (2008). Large eddy simulation and laboratory experiments on the decay of grid wakes in strongly stratified flows. II Nuovo Cimento C 31, 909-930. [12] Matulka, A.; López, P.; Redondo, J. M.; and Tarquis, A. (2014). On the entrainment coefficient in a forced plume: quantitative effects of source parameters. Nonlin. Processes Geophys. 21, 269-278. [13] Castilla R.; Oñate E.; and Redondo J.M. (2007) Models, Experiments and Computations in Turbulence. CIMNE, Barcelona, 255.

Rapid DNA Amplification Using a Battery-Powered Thin-Film Resistive Thermocycler

PubMed Central

Herold, Keith E.; Sergeev, Nikolay; Matviyenko, Andriy; Rasooly, Avraham

2010-01-01

Summary A prototype handheld, compact, rapid thermocycler was developed for multiplex analysis of nucleic acids in an inexpensive, portable configuration. Instead of the commonly used Peltier heating/cooling element, electric thin-film resistive heater and a miniature fan enable rapid heating and cooling of glass capillaries leading to a simple, low-cost Thin-Film Resistive Thermocycler (TFRT). Computer-based pulse width modulation control yields heating rates of 6–7 K/s and cooling rates of 5 K/s. The four capillaries are closely coupled to the heater, resulting in low power consumption. The energy required by a nominal PCR cycle (20 s at each temperature) was found to be 57 ± 2 J yielding an average power of approximately 1.0 W (not including the computer and the control system). Thus the device can be powered by a standard 9 V alkaline battery (or other 9 V power supply). The prototype TFRT was demonstrated (in a benchtop configuration) for detection of three important food pathogens (E. coli ETEC, Shigella dysenteriae, and Salmonella enterica). PCR amplicons were analyzed by gel electrophoresis. The 35 cycle PCR protocol using a single channel was completed in less then 18 min. Simple and efficient heating/cooling, low cost, rapid amplification, and low power consumption make the device suitable for portable DNA amplification applications including clinical point of care diagnostics and field use. PMID:19159110

Graph configuration model based evaluation of the education-occupation match

PubMed Central

2018-01-01

To study education—occupation matchings we developed a bipartite network model of education to work transition and a graph configuration model based metric. We studied the career paths of 15 thousand Hungarian students based on the integrated database of the National Tax Administration, the National Health Insurance Fund, and the higher education information system of the Hungarian Government. A brief analysis of gender pay gap and the spatial distribution of over-education is presented to demonstrate the background of the research and the resulted open dataset. We highlighted the hierarchical and clustered structure of the career paths based on the multi-resolution analysis of the graph modularity. The results of the cluster analysis can support policymakers to fine-tune the fragmented program structure of higher education. PMID:29509783

Graph configuration model based evaluation of the education-occupation match.

PubMed

Gadar, Laszlo; Abonyi, Janos

2018-01-01

To study education-occupation matchings we developed a bipartite network model of education to work transition and a graph configuration model based metric. We studied the career paths of 15 thousand Hungarian students based on the integrated database of the National Tax Administration, the National Health Insurance Fund, and the higher education information system of the Hungarian Government. A brief analysis of gender pay gap and the spatial distribution of over-education is presented to demonstrate the background of the research and the resulted open dataset. We highlighted the hierarchical and clustered structure of the career paths based on the multi-resolution analysis of the graph modularity. The results of the cluster analysis can support policymakers to fine-tune the fragmented program structure of higher education.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, S.; Rohlfing, E.A.; Rahn, L.A.

We present analytical signal expressions for each two-color resonant four-wave mixing (TC-RFWM) scheme that can be used for double-resonance molecular spectroscopy in the limit of weak fields (no saturation). The theoretical approach employs time-independent, diagrammatic perturbation theory and a spherical tensor analysis in an extension of recent treatments of degenerate four-wave mixing [S. Williams, R. N. Zare, and L. A. Rahn, J. Chem. Phys. {bold 101}, 1072 (1994)] and TC-RFWM for the specific case of stimulated emission pumping [S. Williams {ital et al.}, J. Chem. Phys. {bold 102}, 8342 (1995)]. Under the assumption that the relaxation of the population, themore » orientation, and the alignment are the same, simple analytic expressions are derived for commonly used experimental configurations. The TC-RFWM signal is found to be a product of a concentration term, a one-photon molecular term, a line shape function, and a laboratory-frame geometric factor. These expressions are intended to facilitate the practical analysis of TC-RFWM spectra by clarifying, for example, the dependence on beam polarizations and rotational branch combinations. {copyright} {ital 1997 American Institute of Physics.}« less

The expanding universe of mass analyzer configurations for biological analysis.

PubMed

Calvete, Juan J

2014-01-01

Mass spectrometry (MS) is an analytical technique that measures the mass-to-charge ratio of electrically charged gas-phase particles. All mass spectrometers combine ion formation, mass analysis, and ion detection. Although mass analyzers can be regarded as sophisticated devices that manipulate ions in space and time, the rich diversity of possible ways to combine ion separation, focusing, and detection in dynamic mass spectrometers accounts for the large number of instrument designs. A historical perspective of the progress in mass spectrometry that since 1965 until today have contributed to position this technique as an indispensable tool for biological research has been recently addressed by a privileged witness of this golden age of MS (Gelpí J. Mass Spectrom 43:419-435, 2008; Gelpí J. Mass Spectrom 44:1137-1161, 2008). The aim of this chapter is to highlight the view that the operational principles of mass spectrometry can be understood by a simple mathematical language, and that an understanding of the basic concepts of mass spectrometry is necessary to take the most out of this versatile technique.

Absolute configuration of acremoxanthone C, a potent calmodulin inhibitor from Purpureocillium lilacinum.

PubMed

Madariaga-Mazón, Abraham; González-Andrade, Martín; González, María Del Carmen; Glenn, Anthony E; Cerda-García-Rojas, Carlos M; Mata, Rachel

2013-08-23

Bioassay-guided fractionation of an extract prepared from the culture medium and mycelium of Purpureocillium lilacinum allowed the isolation of two calmodulin (CaM) inhibitors, namely, acremoxanthone C (1) and acremonidin A (2). The absolute configuration of 1 was established as 2R, 3R, 1'S, 11'S, and 14'R through extensive NMR spectroscopy and molecular modeling calculations at the DFT B3LYP/DGDZVP level, which included the comparison between theoretical and experimental specific rotation, ³J(C,H), and ³J(H,H) values. Compounds 1 and 2 bind to the human calmodulin (hCaM) biosensor hCaM M124C-mBBr, with dissociation constants (Kd) of 18.25 and 19.40 nM, respectively, 70-fold higher than that of chlorpromazine (Kd = 1.24 μM), used as positive control. Docking analysis using AutoDock 4.2 predicted that 1 and 2 bind to CaM at a similar site to that which KAR-2 binds, which is unusual. Furthermore, a novel, sensible, and specific fluorescent biosensor of hCaM, i.e., hCaM T110C-mBBr, was constructed; this device is labeled at a site where classical inhibitors do not interact and was successfully applied to measure the interaction of 1 with CaM. This is the first report of xanthone-anthraquinone heterodimers in species of Paecilomyces or Purpureocillium genera.

Generic Degraded Congiguration Probability Analysis for DOE Codisposal Waste Package

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.F.A. Deng; M. Saglam; L.J. Gratton

2001-05-23

In accordance with the technical work plan, ''Technical Work Plan For: Department of Energy Spent Nuclear Fuel Work Packages'' (CRWMS M&O 2000c), this Analysis/Model Report (AMR) is developed for the purpose of screening out degraded configurations for U.S. Department of Energy (DOE) spent nuclear fuel (SNF) types. It performs the degraded configuration parameter and probability evaluations of the overall methodology specified in the ''Disposal Criticality Analysis Methodology Topical Report'' (YMP 2000, Section 3) to qualifying configurations. Degradation analyses are performed to assess realizable parameter ranges and physical regimes for configurations. Probability calculations are then performed for configurations characterized by k{submore » eff} in excess of the Critical Limit (CL). The scope of this document is to develop a generic set of screening criteria or models to screen out degraded configurations having potential for exceeding a criticality limit. The developed screening criteria include arguments based on physical/chemical processes and probability calculations and apply to DOE SNF types when codisposed with the high-level waste (HLW) glass inside a waste package. The degradation takes place inside the waste package and is long after repository licensing has expired. The emphasis of this AMR is on degraded configuration screening and the probability analysis is one of the approaches used for screening. The intended use of the model is to apply the developed screening criteria to each DOE SNF type following the completion of the degraded mode criticality analysis internal to the waste package.« less

An approximation method for configuration optimization of trusses

NASA Technical Reports Server (NTRS)

Hansen, Scott R.; Vanderplaats, Garret N.

1988-01-01

Two- and three-dimensional elastic trusses are designed for minimum weight by varying the areas of the members and the location of the joints. Constraints on member stresses and Euler buckling are imposed and multiple static loading conditions are considered. The method presented here utilizes an approximate structural analysis based on first order Taylor series expansions of the member forces. A numerical optimizer minimizes the weight of the truss using information from the approximate structural analysis. Comparisons with results from other methods are made. It is shown that the method of forming an approximate structural analysis based on linearized member forces leads to a highly efficient method of truss configuration optimization.

Theoretical study of ozone adsorption on the surface of Fe, Co and Ni doped boron nitride nanosheets

NASA Astrophysics Data System (ADS)

Farmanzadeh, Davood; Askari Ardehjani, Nastaran

2018-06-01

In this work, the adsorption of ozone molecule on Fe, Co and Ni doped boron nitride nanosheets (BNNSs) were investigated using density functional theory. The most stable adsorption configurations, charge transfer and adsorption energy of ozone molecule on pure and doped BNNSs are calculated. It is shown that ozone molecule has no remarkable interaction with pure boron nitride nanosheet, it tends to be chemisorbed on Fe, Co and Ni doped BNNSs with adsorption energy in the range of -249.4 to -686.1 kJ/mol. In all configurations, the adsorption of ozone molecule generates a semiconductor by reducing Eg in the pure and Fe, Co and Ni doped boron nitride nanosheet. It shows that the conductance of BNNSs change over the adsorption of ozone molecule. The obtained results in this study can be used in developing BN-based sheets for ozone molecule removal.

Lipid intermediates in membrane fusion: formation, structure, and decay of hemifusion diaphragm.

PubMed

Kozlovsky, Yonathan; Chernomordik, Leonid V; Kozlov, Michael M

2002-11-01

Lipid bilayer fusion is thought to involve formation of a local hemifusion connection, referred to as a fusion stalk. The subsequent fusion stages leading to the opening of a fusion pore remain unknown. The earliest fusion pore could represent a bilayer connection between the membranes and could be formed directly from the stalk. Alternatively, fusion pore can form in a single bilayer, referred to as hemifusion diaphragm (HD), generated by stalk expansion. To analyze the plausibility of stalk expansion, we studied the pathway of hemifusion theoretically, using a recently developed elastic model. We show that the stalk has a tendency to expand into an HD for lipids with sufficiently negative spontaneous splay, (~)J(s)< 0. For different experimentally relevant membrane configurations we find two characteristic values of the spontaneous splay. (~)J*(s) and (~)J**(s), determining HD dimension. The HD is predicted to have a finite equilibrium radius provided that the spontaneous splay is in the range (~)J**(s)< (~)J(s)<(~)J*(s), and to expand infinitely for (~)J(s)<(~)J**(s). In the case of common lipids, which do not fuse spontaneously, an HD forms only under action of an external force pulling the diaphragm rim apart. We calculate the dependence of the HD radius on this force. To address the mechanism of fusion pore formation, we analyze the distribution of the lateral tension emerging in the HD due to the establishment of lateral equilibrium between the deformed and relaxed portions of lipid monolayers. We show that this tension concentrates along the HD rim and reaches high values sufficient to rupture the bilayer and form the fusion pore. Our analysis supports the hypothesis that transition from a hemifusion to a fusion pore involves radial expansion of the stalk.

Architecutres, Models, Algorithms, and Software Tools for Configurable Computing

DTIC Science & Technology

2000-03-06

and J.G. Nash. The gated interconnection network for dynamic programming. Plenum, 1988 . [18] Ju wook Jang, Heonchul Park, and Viktor K. Prasanna. A ...Sep. 1997. [2] C. Ebeling, D. C. Cronquist , P. Franklin and C. Fisher, "RaPiD - A configurable computing architecture for compute-intensive...ABSTRACT (Maximum 200 words) The Models, Algorithms, and Architectures for Reconfigurable Computing (MAARC) project developed a sound framework for

Creaming enhancement in a liter scale ultrasonic reactor at selected transducer configurations and frequencies.

PubMed

Juliano, Pablo; Temmel, Sandra; Rout, Manoj; Swiergon, Piotr; Mawson, Raymond; Knoerzer, Kai

2013-01-01

Recent research has shown that high frequency ultrasound (0.4-3 MHz), can enhance milkfat separation in small scale systems able to treat only a few milliliters of sample. In this work, the effect of ultrasonic standing waves on milkfat creaming was studied in a 6L reactor and the influence of different frequencies and transducer configurations in direct contact with the fluid was investigated. A recombined coarse milk emulsion with fat globules stained with oil-red-O dye was selected for the separation trials. Runs were performed with one or two transducers placed in vertical (parallel or perpendicular) and horizontal positions (at the reactor base) at 0.4, 1 and/or 2 MHz (specific energy 8.5 ± 0.6 kJ/kg per transducer). Creaming behavior was assessed by measuring the thickness of the separated cream layer. Other methods supporting this assessment included the measurement of fat content, backscattering, particle size distribution, and microscopy of samples taken at the bottom and top of the reactor. Most efficient creaming was found after treatment at 0.4 MHz in single and double vertical transducer configurations. Among these configurations, a higher separation rate was obtained when sonicating at 0.4 MHz in a vertical perpendicular double transducer setup. The horizontal transducer configuration promoted creaming at 2 MHz only. Fat globule size increase was observed when creaming occurred. This research highlights the potential for enhanced separation of milkfat in larger scale systems from selected transducer configurations in contact with a dairy emulsion, or emulsion splitting in general. Copyright © 2012 Elsevier B.V. All rights reserved.

The Ties that Bind (the Igh Locus).

PubMed

Krangel, Michael S

2016-05-01

Immunoglobulin heavy-chain locus V(D)J recombination requires a 3D chromatin organization which permits widely distributed variable (V) gene segments to contact distant diversity (D) and joining (J) gene segments. A recent study has identified key nodes in the locus interactome, paving the way for new molecular insights into how the locus is configured for recombination. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development Status of the J-2X

NASA Technical Reports Server (NTRS)

Kynard, Mike; Vilja, John

2008-01-01

In June 2006, the NASA Marshall Space Flight Center (MSFC) and Pratt & Whitney Rocketdyne began development of an engine for use on the Ares I crew launch vehicle and the Ares V cargo launch vehicle. The development program will be completed in December 2012 at the end of a Design Certification Review and after certification testing of two flight configuration engines. A team of over 600 people within NASA and Pratt & Whitney Rocketdyne are currently working to prepare for the fall 2008 Critical Design Review (CDR), along with supporting an extensive risk mitigation test program. The J-2X will power the Ares I upper stage and the Ares V earth departure stage (EDS). The initial use will be in the Ares I, used to launch the Orion crew exploration vehicle. In this application, it will power the upper stage after being sent aloft on a Space Shuttle-derived. 5-segment solid rocket booster first stage. In this mission. the engine will ignite at altitude and provide the necessary acceleration force to allow the Orion to achieve orbital velocity. The Ares I upper stage, along with the J-2X. will then be expended. On the Ares V. first stage propulsion is provided by five RS-68B engines and two 5-segment boosters similar to the Ares I configuration. In the Ares V mission. the J-2X is first started to power the EDS and its payload. the Altair lunar lander. into earth orbit, then shut-down and get prepared for its next start. The EDS/Altair will remain in a parking orbit, awaiting rendezvous and docking with Orion. Once the two spacecraft are mated, the J-2X will be restarted to achieve earth departure velocity. After powering the Orion and Altair, the EDS will be expended. By using the J-2X Engine in both applications, a significant infrastructure cost savings is realized. Only one engine development is required, and the sustaining engineering and flight support infrastructures can be combined. There is also flexibility for changing, the production and flight manifest because a single production line can support both missions with minimal differences between each engine configuration kit.

High-energy terahertz wave parametric oscillator with a surface-emitted ring-cavity configuration.

PubMed

Yang, Zhen; Wang, Yuye; Xu, Degang; Xu, Wentao; Duan, Pan; Yan, Chao; Tang, Longhuang; Yao, Jianquan

2016-05-15

A surface-emitted ring-cavity terahertz (THz) wave parametric oscillator has been demonstrated for high-energy THz output and fast frequency tuning in a wide frequency range. Through the special optical design with a galvano-optical scanner and four-mirror ring-cavity structure, the maximum THz wave output energy of 12.9 μJ/pulse is achieved at 1.359 THz under the pump energy of 172.8 mJ. The fast THz frequency tuning in the range of 0.7-2.8 THz can be accessed with the step response of 600 μs. Moreover, the maximum THz wave output energy from this configuration is 3.29 times as large as that obtained from the conventional surface-emitted THz wave parametric oscillator with the same experimental conditions.

Aircraft Configuration Noise Reduction. Volume 3. Computer Program Source Listing

DTIC Science & Technology

1976-06-01

CAT GEN 11 12=1 1+11 CATGtN 32 0360 REAOIKI,10CENIj=4C)(OT(J),.I=11,I2) CATCEN 33 REAO(KI, 100) fDI (JbJ=I#Ii) CATGtkN 34 IF (EOF(KI)) 4C9 20 CATGEN...CORE ANu IURBINE CGNVk 1 COMMON/COREIN/T13,PP3,cMF3,EX3,oELT3,J83, CONVR 13 CONVR 1’ C =5 EXIT FANC .,NVx i COMMUN/FANUAT/NSIG45,NLET45,NAFT45,1CP45,N845

PSHAe (Probabilistic Seismic Hazard enhanced): the case of Istanbul.

NASA Astrophysics Data System (ADS)

Stupazzini, Marco; Allmann, Alexander; Infantino, Maria; Kaeser, Martin; Mazzieri, Ilario; Paolucci, Roberto; Smerzini, Chiara

2016-04-01

The Probabilistic Seismic Hazard Analysis (PSHA) only relying on GMPEs tends to be insufficiently constrained at short distances and data only partially account for the rupture process, seismic wave propagation and three-dimensional (3D) complex configurations. Given a large and representative set of numerical results from 3D scenarios, analysing the resulting database from a statistical point of view and implementing the results as a generalized attenuation function (GAF) into the classical PSHA might be an appealing way to deal with this problem (Villani et al., 2014). Nonetheless, the limited amount of computational resources or time available tend to pose substantial constrains in a broad application of the previous method and, furthermore, the method is only partially suitable for taking into account the spatial correlation of ground motion as modelled by each forward physics-based simulation (PBS). Given that, we envision a streamlined and alternative implementation of the previous approach, aiming at selecting a limited number of scenarios wisely chosen and associating them a probability of occurrence. The experience gathered in the past year regarding 3D modelling of seismic wave propagation in complex alluvial basin (Pilz et al., 2011, Guidotti et al., 2011, Smerzini and Villani, 2012) allowed us to enhance the choice of simulated scenarios in order to explore the variability of ground motion, preserving the full spatial correlation necessary for risk modelling, on one hand and on the other the simulated losses for a given location and a given building stock. 3D numerical modelling of scenarios occurring the North Anatolian Fault in the proximity of Istanbul are carried out through the spectral element code SPEED (http://speed.mox.polimi.it). The results are introduced in a PSHA, exploiting the capabilities of the proposed methodology against a traditional approach based on GMPE. References Guidotti R, M Stupazzini, C Smerzini, R Paolucci, P Ramieri, "Numerical Study on the Role of Basin Geometry and Kinematic Seismic Source in 3D Ground Motion Simulation of the 22 February 2011 M-W 6.2 Christchurch Earthquake", SRL 11/2011; 82(6):767-782. DOI:10.1785/gssrl.82.6.767 Pilz M,Parolai S, Stupazzini M, Paolucci P and Zschau J, "Modelling basin effects on earthquake ground motion in the Santiago de Chile basin by a spectral element code", GJI 11/2011, 187(2):929-945. DOI: 10.1111/j.1365-246X.2011.05183.x Smerzini C and Villani M, "Broadband Numerical Simulations in Complex Near-Field Geological Configurations: The Case of the 2009 Mw 6.3 L'Aquila Earthquake", BSSA 12/2012; 102(6):2436-2451. DOI:10.1785/0120120002 Villani M, Faccioli E, Ordaz M, Stupazzini M, "High-Resolution Seismic Hazard Analysis in a Complex Geological Configuration: The Case of the Sulmona Basin in Central Italy", Earthquake Spectra, 11/2014; 30(4):1801-1824. DOI: 10.1193/112911EQS288M

Configurations of Activity: From the Coupling of Individual Actions to the Emergence of Collective Activity. A Study of Mathematics Teaching Situation in Primary School

ERIC Educational Resources Information Center

Veyrunes, Philippe; Gal-Petitfaux, Nathalie; Durand, Marc

2009-01-01

This article presents and uses the notion of configuration of activity, which extends the Norbert Elias's original concept of social configuration based on the study and analysis of individual and collective activity. Although this concept embraces all types of social activities, in the present study the authors used it to describe and analyse…

Spectroscopic accuracy directly from quantum chemistry: application to ground and excited states of beryllium dimer.

PubMed

Sharma, Sandeep; Yanai, Takeshi; Booth, George H; Umrigar, C J; Chan, Garnet Kin-Lic

2014-03-14

We combine explicit correlation via the canonical transcorrelation approach with the density matrix renormalization group and initiator full configuration interaction quantum Monte Carlo methods to compute a near-exact beryllium dimer curve, without the use of composite methods. In particular, our direct density matrix renormalization group calculations produce a well-depth of D(e) = 931.2 cm(-1) which agrees very well with recent experimentally derived estimates D(e) = 929.7±2 cm(-1) [J. M. Merritt, V. E. Bondybey, and M. C. Heaven, Science 324, 1548 (2009)] and D(e) = 934.6 cm(-1) [K. Patkowski, V. Špirko, and K. Szalewicz, Science 326, 1382 (2009)], as well the best composite theoretical estimates, D(e) = 938±15 cm(-1) [K. Patkowski, R. Podeszwa, and K. Szalewicz, J. Phys. Chem. A 111, 12822 (2007)] and D(e) = 935.1±10 cm(-1) [J. Koput, Phys. Chem. Chem. Phys. 13, 20311 (2011)]. Our results suggest possible inaccuracies in the functional form of the potential used at shorter bond lengths to fit the experimental data [J. M. Merritt, V. E. Bondybey, and M. C. Heaven, Science 324, 1548 (2009)]. With the density matrix renormalization group we also compute near-exact vertical excitation energies at the equilibrium geometry. These provide non-trivial benchmarks for quantum chemical methods for excited states, and illustrate the surprisingly large error that remains for 1 ¹Σ(g)⁻ state with approximate multi-reference configuration interaction and equation-of-motion coupled cluster methods. Overall, we demonstrate that explicitly correlated density matrix renormalization group and initiator full configuration interaction quantum Monte Carlo methods allow us to fully converge to the basis set and correlation limit of the non-relativistic Schrödinger equation in small molecules.

Mixing and NO(x) Emission Calculations of Confined Reacting Jet Flows in a Cylindrical Duct

NASA Technical Reports Server (NTRS)

Holdeman, James D. (Technical Monitor); Oechsle, Victor L.

2003-01-01

Rapid mixing of cold lateral jets with hot cross-stream flows in confined configurations is of practical interest in gas turbine combustors as it strongly affects combustor exit temperature quality, and gaseous emissions in for example rich-lean combustion. It is therefore important to further improve our fundamental understanding of the important processes of dilution jet mixing especially when the injected jet mass flow rate exceeds that of the cross-stream. The results reported in this report describe some of the main flow characteristics which develop in the mixing process in a cylindrical duct. A 3-dimensional tool has been used to predict the mixing flow field characteristics and NOx emission in a quench section of an RQL combustor, Eighteen configurations have been analyzed in a circular geometry in a fully reacting environment simulating the operating condition of an actual RQL gas turbine combustion liner. The evaluation matrix was constructed by varying three parameters: 1) jet-to-mainstream momentum-flux ratio (J), 2) orifice shape or orifice aspect ratio, and 3) slot slant angle. The results indicate that the mixing flow field significantly varies with the value of the jet penetration and subsequently, slanting elongated slots generally improve the mixing uniformity at high J conditions. Round orifices produce more uniform mixing and low NO(x) emissions at low J due to the strong and adequate jet penetration. No significant correlation was found between the NO(x) production rates and the mixing deviation parameters, however, strong correlation was found between NO(x) formation and jet penetration. In the computational results, most of the NO(x) formation occurred behind the orifice starting at the orifice wake region. Additional NO(x) is formed upstream of the orifice in certain configurations with high J conditions due to the upstream recirculation.

Terbium to Quantum Dot FRET Bioconjugates for Clinical Diagnostics: Influence of Human Plasma on Optical and Assembly Properties

DTIC Science & Technology

2011-10-12

Periasamy, A. Fluorescence Resonance Energy Transfer (FRET) microscopy imaging of live cell protein localization. J . Cell. Biol. 2003, 5, 629-633. 4...tissues. Physiol. Rev. 2010, 90, 1103-1163. 10. Woehler, A.; Wlodarczyk, J .; Neher, E. Signal/noise analysis of FRET-based sensors. Biophys. J . 2010...99, 2344-2354. 11. Selvin, P.R. Lanthanide-based resonance energy transfer. IEEE J . Sel. Top. Quant. Electron. 1996, 2, 1077-1087. 12. Van der Meer

Analysis and Preliminary Design of an Advanced Technology Transport Flight Control System

NASA Technical Reports Server (NTRS)

Frazzini, R.; Vaughn, D.

1975-01-01

The analysis and preliminary design of an advanced technology transport aircraft flight control system using avionics and flight control concepts appropriate to the 1980-1985 time period are discussed. Specifically, the techniques and requirements of the flight control system were established, a number of candidate configurations were defined, and an evaluation of these configurations was performed to establish a recommended approach. Candidate configurations based on redundant integration of various sensor types, computational methods, servo actuator arrangements and data-transfer techniques were defined to the functional module and piece-part level. Life-cycle costs, for the flight control configurations, as determined in an operational environment model for 200 aircraft over a 15-year service life, were the basis of the optimum configuration selection tradeoff. The recommended system concept is a quad digital computer configuration utilizing a small microprocessor for input/output control, a hexad skewed set of conventional sensors for body rate and body acceleration, and triple integrated actuators.

Evaluating the Efficacy of Wavelet Configurations on Turbulent-Flow Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Shaomeng; Gruchalla, Kenny; Potter, Kristin

2015-10-25

I/O is increasingly becoming a significant constraint for simulation codes and visualization tools on modern supercomputers. Data compression is an attractive workaround, and, in particular, wavelets provide a promising solution. However, wavelets can be applied in multiple configurations, and the variations in configuration impact accuracy, storage cost, and execution time. While the variation in these factors over wavelet configurations have been explored in image processing, they are not well understood for visualization and analysis of scientific data. To illuminate this issue, we evaluate multiple wavelet configurations on turbulent-flow data. Our approach is to repeat established analysis routines on uncompressed andmore » lossy-compressed versions of a data set, and then quantitatively compare their outcomes. Our findings show that accuracy varies greatly based on wavelet configuration, while storage cost and execution time vary less. Overall, our study provides new insights for simulation analysts and visualization experts, who need to make tradeoffs between accuracy, storage cost, and execution time.« less

Atomistic models of vacancy-mediated diffusion in silicon

NASA Astrophysics Data System (ADS)

Dunham, Scott T.; Wu, Can Dong

1995-08-01

Vacancy-mediated diffusion of dopants in silicon is investigated using Monte Carlo simulations of hopping diffusion, as well as analytic approximations based on atomistic considerations. Dopant/vacancy interaction potentials are assumed to extend out to third-nearest neighbor distances, as required for pair diffusion theories. Analysis focusing on the third-nearest neighbor sites as bridging configurations for uncorrelated hops leads to an improved analytic model for vacancy-mediated dopant diffusion. The Monte Carlo simulations of vacancy motion on a doped silicon lattice verify the analytic results for moderate doping levels. For very high doping (≳2×1020 cm-3) the simulations show a very rapid increase in pair diffusivity due to interactions of vacancies with more than one dopant atom. This behavior has previously been observed experimentally for group IV and V atoms in silicon [Nylandsted Larsen et al., J. Appl. Phys. 73, 691 (1993)], and the simulations predict both the point of onset and doping dependence of the experimentally observed diffusivity enhancement.

Tethered satellite system control using electromagnetic forces and reaction wheels

NASA Astrophysics Data System (ADS)

Alandi Hallaj, Mohammad Amin; Assadian, Nima

2015-12-01

In this paper a novel non-rotating space tethered configuration is introduced which its relative positions controlled using electromagnetic forces. The attitude dynamics is controlled by three reaction wheels in the body axes. The nonlinear coupled orbital dynamics of a dumbbell tethered satellite formation flight are derived through a constrained Lagrangian approach. These equations are presented in the leader satellite orbital frame. The tether is assumed to be mass-less and straight, and the J2 perturbation is included to the analysis. The forces and the moments of the electromagnetic coils are modeled based on the far-filed model of the magnetic dipoles. A guidance scheme for generating the desired positions as a function of time in Cartesian form is presented. The satellite tethered formation with variable length is controlled utilizing a linear controller. This approach is applied to a specified scenario and it is shown that the nonlinear guidance method and the linear controller can control the nonlinear system of the tethered formation and the results are compared with optimal control approach.

Atomistic Method Applied to Computational Modeling of Surface Alloys

NASA Technical Reports Server (NTRS)

Bozzolo, Guillermo H.; Abel, Phillip B.

2000-01-01

The formation of surface alloys is a growing research field that, in terms of the surface structure of multicomponent systems, defines the frontier both for experimental and theoretical techniques. Because of the impact that the formation of surface alloys has on surface properties, researchers need reliable methods to predict new surface alloys and to help interpret unknown structures. The structure of surface alloys and when, and even if, they form are largely unpredictable from the known properties of the participating elements. No unified theory or model to date can infer surface alloy structures from the constituents properties or their bulk alloy characteristics. In spite of these severe limitations, a growing catalogue of such systems has been developed during the last decade, and only recently are global theories being advanced to fully understand the phenomenon. None of the methods used in other areas of surface science can properly model even the already known cases. Aware of these limitations, the Computational Materials Group at the NASA Glenn Research Center at Lewis Field has developed a useful, computationally economical, and physically sound methodology to enable the systematic study of surface alloy formation in metals. This tool has been tested successfully on several known systems for which hard experimental evidence exists and has been used to predict ternary surface alloy formation (results to be published: Garces, J.E.; Bozzolo, G.; and Mosca, H.: Atomistic Modeling of Pd/Cu(100) Surface Alloy Formation. Surf. Sci., 2000 (in press); Mosca, H.; Garces J.E.; and Bozzolo, G.: Surface Ternary Alloys of (Cu,Au)/Ni(110). (Accepted for publication in Surf. Sci., 2000.); and Garces, J.E.; Bozzolo, G.; Mosca, H.; and Abel, P.: A New Approach for Atomistic Modeling of Pd/Cu(110) Surface Alloy Formation. (Submitted to Appl. Surf. Sci.)). Ternary alloy formation is a field yet to be fully explored experimentally. The computational tool, which is based on the BFS (Bozzolo, Ferrante, and Smith) method for the calculation of the energetics, consists of a small number of simple PCbased computer codes that deal with the different aspects of surface alloy formation. Two analysis modes are available within this package. The first mode provides an atom-by-atom description of real and virtual stages 1. during the process of surface alloying, based on the construction of catalogues of configurations where each configuration describes one possible atomic distribution. BFS analysis of this catalogue provides information on accessible states, possible ordering patterns, and details of island formation or film growth. More importantly, it provides insight into the evolution of the system. Software developed by the Computational Materials Group allows for the study of an arbitrary number of elements forming surface alloys, including an arbitrary number of surface atomic layers. The second mode involves large-scale temperature-dependent computer 2. simulations that use the BFS method for the energetics and provide information on the dynamic processes during surface alloying. These simulations require the implementation of Monte-Carlo-based codes with high efficiency within current workstation environments. This methodology capitalizes on the advantages of the BFS method: there are no restrictions on the number or type of elements or on the type of crystallographic structure considered. This removes any restrictions in the definition of the configuration catalogues used in the analytical calculations, thus allowing for the study of arbitrary ordering patterns, ultimately leading to the actual surface alloy structure. Moreover, the Monte Carlo numerical technique used for the large-scale simulations allows for a detailed visualization of the simulated process, the main advantage of this type of analysis being the ability to understand the underlying features that drive these processes. Because of the simplicity of the BFS method for e energetics used in these calculations, a detailed atom-by-atom analysis can be performed at any point in the simulation, providing necessary insight on the details of the process. The main objective of this research program is to develop a tool to guide experimenters in understanding and interpreting often unexpected results in alloy formation experiments. By reducing the computational effort without losing physical accuracy, we expect that powerful simulation tools will be developed in the immediate future, which will allow material scientists to easily visualize and analyze processes at a level not achievable experimentally.

Fracture Mechanics Analysis of Stitched Stiffener-Skin Debonding

NASA Technical Reports Server (NTRS)

Glaessgen, E. H.; Raju, I. S.; Poe, C. C., Jr.

1998-01-01

An analysis based on plate finite elements and the virtual crack closure technique has been implemented to study the effect of stitching on mode I and mode II strain energy release rates for debond configurations. The stitches were modeled as discrete nonlinear fastener elements with a compliance determined by experiment. The axial and shear behavior of the stitches was considered, however, the two compliances and failure loads were assumed to be independent. Both a double cantilever beam (mode I) and a mixed mode skin-stiffener debond configuration were studied. In the double cantilever beam configurations, G(sub I) began to decrease once the debond had grown beyond the first row of stitches and was reduced to zero for long debonds. In the mixed-mode skin-stiffener configurations, G(sub I) showed a similar behavior as in the double cantilever beam configurations, however, G(sub u), continued to increase with increasing debond length.

An Approach for Implementation of Project Management Information Systems

NASA Astrophysics Data System (ADS)

Běrziša, Solvita; Grabis, Jānis

Project management is governed by project management methodologies, standards, and other regulatory requirements. This chapter proposes an approach for implementing and configuring project management information systems according to requirements defined by these methodologies. The approach uses a project management specification framework to describe project management methodologies in a standardized manner. This specification is used to automatically configure the project management information system by applying appropriate transformation mechanisms. Development of the standardized framework is based on analysis of typical project management concepts and process and existing XML-based representations of project management. A demonstration example of project management information system's configuration is provided.

Initiation of a Relativistic Magnetron

NASA Astrophysics Data System (ADS)

Kaup, D. J.

2003-10-01

We report on recent results in our studies of relativistic magnetrons. Experimentally, these devices have proven to be very difficult to operate, typically cutting off too quickly after they are initialized, and therefore not delivering the power levels expected [1]. Our analysis is based on our model of a crossed-field device, consisting only of its two dominant modes, a DC background and an RF oscillating mode [2]. This approach has produced generally quantitatively correct values for the operating regime and major features of nonrelativistic devices. We have performed a fully electromagnetic, relativistic analysis of a magnetron of the A6 cylindrical configuration. We will show that when the device should generate maximum power, it enters a regime where the DC background could become potentially unstable. In particular, when a nonrelativistic planar device enters the saturation regime, the DC electron density distribution could become unstable if the vertical DC velocity would ever become equal to the magnitude of the vertical RF velocity [3]. We find that during the initiation phase, for the highest power levels of our model of the A6, near the cathode, the DC vertical velocity does become just less than, and definitely on the order of the magnitude of the vertical RF velocity. Consequently, any localized surge in the currents near the cathode, could easily destroy the smooth upward flow of the electrons, drive the DC background unstable, and thereby shut down the operation of the device. [1] Long-pulse relativistic magnetron experiments, M.R. Lopez, R.M. Gilgenbach, Y.Y. Lau, D.W. Jordan, M.D. Johnston, M.C. Jones, V.B. Neculaes, T.A. Spencer, J.W. Luginsland, M.D. Haworth, R.W.Lemke, D. Price, and L. Ludeking, Proc. of SPIE Aerosense 4720, 10-17, (2002). [2] Theoretical modeling of crossed-field electron vacuum devices, D.J. Kaup, Phys. of Plasmas 8, 2473-80 (2001). [3] Initiation and Stationary Operating States in a Crossed-Field Vacuum Electron Device, D. J. Kaup, Proc. of SPIE Aerosense 4720, 67-74, (2002).

Fracture mechanics analysis for various fiber/matrix interface loadings

NASA Technical Reports Server (NTRS)

Naik, R. A.; Crews, J. H., Jr.

1991-01-01

Fiber/matrix (F/M) cracking was analyzed to provide better understanding and guidance in developing F/M interface fracture toughness tests. Two configurations, corresponding to F/M cracking at a broken fiber and at the free edge, were investigated. The effects of mechanical loading, thermal cooldown, and friction were investigated. Each configuration was analyzed for two loadings: longitudinal and normal to the fiber. A nonlinear finite element analysis was performed to model friction and slip at the F/M interface. A new procedure for fitting a square-root singularity to calculated stresses was developed to determine stress intensity factors (K sub I and K sub II) for a bimaterial interface crack. For the case of F/M cracking at a broken fiber with longitudinal loading, crack tip conditions were strongly influenced by interface friction. As a result, an F/M interface toughness test based on this case was not recommended because nonlinear data analysis methods would be required. For the free edge crack configuration, both mechanical and thermal loading caused crack opening, thereby avoiding frictional effects. A F/M interface toughness test based on this configuration would provide data for K(sub I)/K(sub II) ratios of about 0.7 and 1.6 for fiber and radial normal loading, respectively. However, thermal effects must be accounted for in the data analysis.

Fracture mechanics analysis for various fiber/matrix interface loadings

NASA Technical Reports Server (NTRS)

Naik, Rajiv A.; Crews, John H., Jr.

1992-01-01

Fiber/matrix (F/M) cracking was analyzed to provide better understanding and guidance in developing F/M interface fracture toughness tests. Two configurations, corresponding to F/M cracking at a broken fiber and at the free edge, were investigated. The effects of mechanical loading, thermal cooldown, and friction were investigated. Each configuration was analyzed for two loadings: longitudinal and normal to the fiber. A nonlinear finite element analysis was performed to model friction and slip at the F/M interface. A new procedure for fitting a square-root singularity to calculated stresses was developed to determine stress intensity factors (K sub I and K sub II) for a bimaterial interface crack. For the case of F/M cracking at a broken fiber with longitudinal loading, crack tip conditions were strongly influenced by interface friction. As a result, an F/M interface toughness test based on this case was not recommended because nonlinear data analysis methods would be required. For the free edge crack configuration, both mechanical and thermal loading caused crack opening, theory avoiding fractional effects. A F/M interface toughness test based on this configuration would provide data for K(sub I/K(sub II) ratios of about 0.7 and 1.6 for fiber and radial normal loading, respectively. However, thermal effects must be accounted for in the data analysis.

Fracture mechanics analysis for various fiber/matrix interface loadings

NASA Technical Reports Server (NTRS)

Naik, R. A.; Crews, J. H., Jr.

1991-01-01

Fiber/matrix (F/M) cracking was analyzed to provide better understanding and guidance in developing F/M interface fracture toughness tests. Two configurations, corresponding to F/M cracking at a broken fiber and at the free edge, were investigated. The effects of mechanical loading, thermal cooldown, and friction were investigated. Each configuration was analyzed for two loadings: longitudinal and normal to the fiber. A nonlinear finite element analysis was performed to model friction and slip at the F/M interface. A new procedure for fitting a square-root singularity to calculated stresses was developed to determine stress intensity factors (K sub I and K sub II) for a bimaterial interface crack. For the case of F/M cracking at a broken fiber with longitudinal loading, crack tip conditions were strongly influenced by interface friction. As a result, an F/M interface toughness test based on this case was not recommended because nonlinear data analysis methods would be required. For the free edge crack configuration, both mechanical and thermal loading caused crack opening, thereby avoiding frictional effects. An F/M interface toughness test based on this configuration would provide data for K(sub I)/K(sub II) ratios of about 0.7 and 1.6 for fiber and radial normal loading, respectively. However, thermal effects must be accounted for in the data analysis.

Operational Dynamic Configuration Analysis

NASA Technical Reports Server (NTRS)

Lai, Chok Fung; Zelinski, Shannon

2010-01-01

Sectors may combine or split within areas of specialization in response to changing traffic patterns. This method of managing capacity and controller workload could be made more flexible by dynamically modifying sector boundaries. Much work has been done on methods for dynamically creating new sector boundaries [1-5]. Many assessments of dynamic configuration methods assume the current day baseline configuration remains fixed [6-7]. A challenging question is how to select a dynamic configuration baseline to assess potential benefits of proposed dynamic configuration concepts. Bloem used operational sector reconfigurations as a baseline [8]. The main difficulty is that operational reconfiguration data is noisy. Reconfigurations often occur frequently to accommodate staff training or breaks, or to complete a more complicated reconfiguration through a rapid sequence of simpler reconfigurations. Gupta quantified a few aspects of airspace boundary changes from this data [9]. Most of these metrics are unique to sector combining operations and not applicable to more flexible dynamic configuration concepts. To better understand what sort of reconfigurations are acceptable or beneficial, more configuration change metrics should be developed and their distribution in current practice should be computed. This paper proposes a method to select a simple sequence of configurations among operational configurations to serve as a dynamic configuration baseline for future dynamic configuration concept assessments. New configuration change metrics are applied to the operational data to establish current day thresholds for these metrics. These thresholds are then corroborated, refined, or dismissed based on airspace practitioner feedback. The dynamic configuration baseline selection method uses a k-means clustering algorithm to select the sequence of configurations and trigger times from a given day of operational sector combination data. The clustering algorithm selects a simplified schedule containing k configurations based on stability score of the sector combinations among the raw operational configurations. In addition, the number of the selected configurations is determined based on balance between accuracy and assessment complexity.

UNO DMRG CASCI calculations of effective exchange integrals for m-phenylene-bis-methylene spin clusters

NASA Astrophysics Data System (ADS)

Kawakami, Takashi; Sano, Shinsuke; Saito, Toru; Sharma, Sandeep; Shoji, Mitsuo; Yamada, Satoru; Takano, Yu; Yamanaka, Shusuke; Okumura, Mitsutaka; Nakajima, Takahito; Yamaguchi, Kizashi

2017-09-01

Theoretical examinations of the ferromagnetic coupling in the m-phenylene-bis-methylene molecule and its oligomer were carried out. These systems are good candidates for exchange-coupled systems to investigate strong electronic correlations. We studied effective exchange integrals (J), which indicated magnetic coupling between interacting spins in these species. First, theoretical calculations based on a broken-symmetry single-reference procedure, i.e. the UHF, UMP2, UMP4, UCCSD(T) and UB3LYP methods, were carried out with a GAUSSIAN program code under an SR wave function. From these results, the J value by the UHF method was largely positive because of the strong ferromagnetic spin polarisation effect. The J value by the UCCSD(T) and UB3LYP methods improved an overestimation problem by correcting the dynamical electronic correlation. Next, magnetic coupling among these spins was studied using the CAS-based method of the symmetry-adapted multireference methods procedure. Thus, the UNO DMRG CASCI (UNO, unrestricted natural orbital; DMRG, density matrix renormalised group; CASCI, complete active space configuration interaction) method was mainly employed with a combination of ORCA and BLOCK program codes. DMRG CASCI calculations in valence electron counting, which included all orbitals to full valence CI, provided the most reliable result, and support the UB3LYP method for extended systems.

Communication: An accurate global potential energy surface for the ground electronic state of ozone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dawes, Richard, E-mail: dawesr@mst.edu, E-mail: hguo@unm.edu; Lolur, Phalgun; Li, Anyang

We report a new full-dimensional and global potential energy surface (PES) for the O + O{sub 2} → O{sub 3} ozone forming reaction based on explicitly correlated multireference configuration interaction (MRCI-F12) data. It extends our previous [R. Dawes, P. Lolur, J. Ma, and H. Guo, J. Chem. Phys. 135, 081102 (2011)] dynamically weighted multistate MRCI calculations of the asymptotic region which showed the widely found submerged reef along the minimum energy path to be the spurious result of an avoided crossing with an excited state. A spin-orbit correction was added and the PES tends asymptotically to the recently developed long-rangemore » electrostatic model of Lepers et al. [J. Chem. Phys. 137, 234305 (2012)]. This PES features: (1) excellent equilibrium structural parameters, (2) good agreement with experimental vibrational levels, (3) accurate dissociation energy, and (4) most-notably, a transition region without a spurious reef. The new PES is expected to allow insight into the still unresolved issues surrounding the kinetics, dynamics, and isotope signature of ozone.« less

The Effect of Interface Texture on Exchange Biasing in Ni(80)Fe(20)/Ir(20)Mn(80) System.

PubMed

Chen, Yuan-Tsung

2009-01-01

Exchange-biasing phenomenon can induce an evident unidirectional hysteresis loop shift by spin coupling effect in the ferromagnetic (FM)/antiferromagnetic (AFM) interface which can be applied in magnetoresistance random access memory (MRAM) and recording-head applications. However, magnetic properties are the most important to AFM texturing. In this work, top-configuration exchange-biasing NiFe/IrMn(x A) systems have been investigated with three different conditions. From the high-resolution cross-sectional transmission electron microscopy (HR X-TEM) and X-ray diffraction results, we conclude that the IrMn (111) texture plays an important role in exchange-biasing field (H(ex)) and interfacial exchange energy (J(k)). H(ex) and J(k) tend to saturate when the IrMn thickness increases. Moreover, the coercivity (H(c)) dependence on IrMn thickness is explained based on the coupling or decoupling effect between the spins of the NiFe and IrMn layers near the NiFe/IrMn interface. In this work, the optimal values for H(ex) and J(k) are 115 Oe and 0.062 erg/cm(2), respectively.

Response to “Comments on ‘A theoretical model of the pressure distributions arising from asymmetric intraglottal flows applied to a two-mass model of the vocal folds’” [J. Acoust. Soc. Am. 130, 389–403 (2011)

PubMed Central

Erath, Byron D.; Peterson, Sean D.; Zañartu, Matías; Wodicka, George R.; Stewart, Kelley C.; Plesniak, Michael W.

2013-01-01

Hirschberg [J. Acoust. Soc. Am. 134, 9-12 (2013)] presents a commentary and criticisms of the viscous flow model presented by Erath et al. [J. Acoust. Soc. Am. 130, 389–403 (2011)] that solves for the asymmetric pressure loading on the vocal fold walls. This pressure loading arises from asymmetric flow attachment to one vocal fold wall when the glottal channel forms a divergent configuration. Hirschberg proposes an alternative model for the asymmetric loading based upon inviscid flow curvature at the glottal inlet. In this manuscript further evidence is provided in support of the model of Erath et al. and the underlying assumptions, and demonstrates that the primary criticisms presented by Hirschberg are unwarranted. The model presented by Hirschberg is compared with the model from the original paper by Erath et al., and it is shown that each model describes different and complementary aspects of divergent glottal flows. PMID:23927090

Role of binding entropy in the refinement of protein-ligand docking predictions: analysis based on the use of 11 scoring functions.

PubMed

Ruvinsky, Anatoly M

2007-06-01

We present results of testing the ability of eleven popular scoring functions to predict native docked positions using a recently developed method (Ruvinsky and Kozintsev, J Comput Chem 2005, 26, 1089) for estimation the entropy contributions of relative motions to protein-ligand binding affinity. The method is based on the integration of the configurational integral over clusters obtained from multiple docked positions. We use a test set of 100 PDB protein-ligand complexes and ensembles of 101 docked positions generated by (Wang et al. J Med Chem 2003, 46, 2287) for each ligand in the test set. To test the suggested method we compared the averaged root-mean square deviations (RMSD) of the top-scored ligand docked positions, accounting and not accounting for entropy contributions, relative to the experimentally determined positions. We demonstrate that the method increases docking accuracy by 10-21% when used in conjunction with the AutoDock scoring function, by 2-25% with G-Score, by 7-41% with D-Score, by 0-8% with LigScore, by 1-6% with PLP, by 0-12% with LUDI, by 2-8% with F-Score, by 7-29% with ChemScore, by 0-9% with X-Score, by 2-19% with PMF, and by 1-7% with DrugScore. We also compared the performance of the suggested method with the method based on ranking by cluster occupancy only. We analyze how the choice of a clustering-RMSD and a low bound of dense clusters impacts on docking accuracy of the scoring methods. We derive optimal intervals of the clustering-RMSD for 11 scoring functions.

Effects of Breeding Configuration on Maternal and Weanling Behavior in Laboratory Mice.

PubMed

Braden, Gillian C; Rasmussen, Skye; Monette, Sebastien; Tolwani, Ravi J

2017-07-01

Although numerous studies have evaluated the effect of housing density on the wellbeing of laboratory mice, little is known about the effect of breeding configuration on mouse behavior. The 8th edition of the Guide for the Care and Use of Laboratory Animals lists the recommended minimal floor area per animal for a female mouse and her litter as 51 in.2 We sought to determine the effects of pair, trio, and harem breeding configurations on the maternal and weanling behavior of C57BL/6J (B6) and 129S6/SvEvTac (129) mice on the basis of nest scores and performance in pup retrieval tests, open-field test (OFT), elevated plus maze, and tail suspension test; we concurrently evaluated cage microenvironment, reproductive indices, and anatomic and clinical pathology. Harem breeding configurations enhanced B6 maternal behaviors as evidenced by significantly shorter pup retrieval times. Trio- and harem-raised B6 weanlings showed increased exploratory behaviors, as evidenced by greater time spent in the center of the OFT, when compared with pair-raised B6 mice. Conversely, breeding configuration did not alter pup retrieval times for 129 mice, and on the day of weaning trio- and harem-raised 129 mice demonstrated increased anxiety-like behavior, as evidenced by greater time spent in the periphery of the OFT, when compared with pair-raised counterparts. Behavioral differences were not noted on subsequent days for either strain. Trio- and harem-raised B6 and 129 weanling mice had significantly higher weaning weights than weanlings raised in a pair breeding configuration. Trio and harem breeding in a standard 67-in.2 shoebox cage did not detrimentally affect the evaluated welfare parameters in either C57BL/6J or 129S6/SvEvTac mice.

Revised and extended analysis of the fourth spectrum of indium: In IV

NASA Astrophysics Data System (ADS)

Swapnil; Tauheed, A.

2013-11-01

The spectrum of triply ionized indium (In IV) has been investigated in the wavelength region 245-4443 Å. The In3+ is a Pd-like ion with the ground configuration 4p64d10. All levels of the low lying excited configurations 4d95p, 4d9ns (n=5-7), 4d95d and 4d85s2 have been reported earlier, while for the higher configurations 4d9np (n=6,7) and 4d9nf (n=4-11), only the J=1 levels radiatively decaying to the ground level have been reported. The present work extends the analysis to include the 4d96p, 4d96d, 4d94f and 4d95f configurations. A total 116 levels have been established, 56 of them being new. All the previously reported levels have been confirmed except 4d97s 3D1, 4d97p 3P1, 4d96f 3P1 and 4d85s23P1. The experimental data for the present work was recorded on a 3-m normal incidence spectrograph of St. Francis Xavier University, Antigonish (Canada), as well as on the 10.7 m normal and grazing incidence spectrographs of the National institute of Standards and Technology, Gaithersburg (USA). In both laboratories, a triggered spark source was used. The wavelengths above 2000 Å were supplemented from Bhatia's thesis where an electrodeless discharge source was used. Theoretical predictions were made using Cowan's Hartree-Fock-relativstic atomic codes with superposition of configurations. Least squares fitted (LSF) parametric calculations were used to interpret the energy levels. For vacuum ultraviolet wavelength region our wavelength accuracy is ±0.005 Å. We estimate the ionization potential of In IV to be 450,921.7±86.0 cm-1 (55.9072±0.0106 eV).

Utilisation d'analyse de concepts formels pour la gestion de variabilite d'un logiciel configure dynamiquement

NASA Astrophysics Data System (ADS)

Menguy, Theotime

Because of its critical nature, avionic industry is bound with numerous constraints such as security standards and certifications while having to fulfill the clients' desires for personalization. In this context, variability management is a very important issue for re-engineering projects of avionic softwares. In this thesis, we propose a new approach, based on formal concept analysis and semantic web, to support variability management. The first goal of this research is to identify characteristic behaviors and interactions of configuration variables in a dynamically configured system. To identify such elements, we used formal concept analysis on different levels of abstractions in the system and defined new metrics. Then, we built a classification for the configuration variables and their relations in order to enable a quick identification of a variable's behavior in the system. This classification could help finding a systematic approach to process variables during a re-engineering operation, depending on their category. To have a better understanding of the system, we also studied the shared controls of code between configuration variables. A second objective of this research is to build a knowledge platform to gather the results of all the analysis performed, and to store any additional element relevant in the variability management context, for instance new results helping define re-engineering process for each of the categories. To address this goal, we built a solution based on a semantic web, defining a new ontology, very extensive and enabling to build inferences related to the evolution processes. The approach presented here is, to the best of our knowledge, the first classification of configuration variables of a dynamically configured software and an original use of documentation and variability management techniques using semantic web in the aeronautic field. The analysis performed and the final results show that formal concept analysis is a way to identify specific properties and behaviors and that semantic web is a good solution to store and explore the results. However, the use of formal concept analysis with new boolean relations, such as the link between configuration variables and files, and the definition of new inferences may be a way to draw better conclusions. The use of the same methodology with other systems would enable to validate the approach in other contexts.

Wessex Helicopter/Sonar Dynamics Study. ARL Program Description and Operation.

DTIC Science & Technology

1979-02-01

s): 5. Document Date: S illiams, Neil V. February, 1979 Guy, Christopher R. Williams, Maxwell J. 6. Type of Report and Period Covered: Gilbert, Neil...form with the aid of an analog computer type of block diagram, comprising a number of linked modules (called blocks), each one representing a particular...three types of statement, viz. configuration, parameter and function statements. The configuration statements describe the blocks used and specify the

High-gain mid-infrared optical-parametric generation pumped by microchip laser.

PubMed

Ishizuki, Hideki; Taira, Takunori

2016-01-25

High-gain mid-infrared optical-parametric generation was demonstrated by simple single-pass configuration using PPMgLN devices pumped by giant-pulse microchip laser. Effective mid-infrared wavelength conversion with 1 mJ output energy from 2.4 mJ pumping using conventional PPMgLN could be realized. Broadband optical-parametric generation from 1.7 to 2.6 µm could be also measured using chirped PPMgLN.

UV-light induced fabrication of CdCl2 nanotubes through CdSe/Te nanocrystals based on dimension and configuration control.

PubMed

Zeng, Jie; Liu, Chi; Huang, Jianliu; Wang, Xiaoping; Zhang, Shuyuan; Li, Gongpu; Hou, Jianguo

2008-05-01

Since the discovery of WS2 nanotubes in 1992 ( Nature 1992, 360, 444), there have been significant research efforts to synthesize nanotubes and fullerene-like hollow nanoparticles (HNPs) of inorganic materials ( Nat. Nanotechnol. 2006, 1, 103) due to their potential applications as solid lubrications ( J. Mater. Chem. 2005, 15, 1782), chemical sensing ( Adv. Funct. Mater. 2006, 16, 371), drug delivering ( J. Am. Chem. Soc. 2005, 127, 7316), catalysis ( Adv. Mater. 2006, 18, 2561), or quantum harvesting ( Acc. Chem. Res. 2006, 39, 239). Nanotubes can be produced either by rolling up directly from layer compounds ( Nature 2001, 410, 168) or through other mechanisms ( Adv. Mater. 2004, 16, 1497) such as template growth ( Nature 2003, 422, 599) and decomposition ( J. Am. Chem. Soc. 2001, 123, 4841). The Kirkendall effect, a classical phenomenon in metallurgy ( Trans. AIME 1947, 171, 130), was recently exploited to fabricate hollow 0-D nanocrystals ( Science 2004, 304, 711) as well as 1-D nanotubes ( Nat. Mater. 2006, 5, 627). Although the dimension of resulting hollow nanostructures depends on precursors, the hollow nanomaterials can also be organized into various dimensional nanostructures spontaneously or induced by an external field. In this letter, we report, for the first time, the UV-light induced fabrication of the ends-closed 1-D CdCl2 nanotubes from 0-D CdSe solid nanocrystals through the Kirkendall effect and the head-to-end assembled process. Our results demonstrate the possibility to control the dimension (0-D to 1-D) and the configuration (solid to hollow) of nanostructures simultaneously and have implications in fabricating hollow nano-objects from zero-dimensional to multidimensional.

Stability assessment and operating parameter optimization on experimental results in very small plasma focus, using sensitivity analysis

NASA Astrophysics Data System (ADS)

Jafari, Hossein; Habibi, Morteza

2018-04-01

Regarding the importance of stability in small-scale plasma focus devices for producing the repeatable and strength pinching, a sensitivity analysis approach has been used for applicability in design parameters optimization of an actually very low energy device (84 nF, 48 nH, 8-9.5 kV, ∼2.7-3.7 J). To optimize the devices functional specification, four different coaxial electrode configurations have been studied, scanning an argon gas pressure range from 0.6 to 1.5 mbar via the charging voltage variation study from 8.3 to 9.3 kV. The strength and efficient pinching was observed for the tapered anode configuration, over an expanded operating pressure range of 0.6 to 1.5 mbar. The analysis results showed that the most sensitive of the pinch voltage was associated with 0.88 ± 0.8mbar argon gas pressure and 8.3-8.5 kV charging voltage, respectively, as the optimum operating parameters. From the viewpoint of stability assessment of the device, it was observed that the least variation in stable operation of the device was for a charging voltage range of 8.3 to 8.7 kV in an operating pressure range from 0.6 to 1.1 mbar.

Liquid Chromatographic Analysis of Nitrocellulose-Base Propellants

DTIC Science & Technology

1983-03-28

18 radial PkC column using 10 micron silica coated with octadecyl silane. The detector was a LC 85 variable wavelength UV detector from Perkin-Elmer...Snyder, L. R. J Chrom Scd i6, (1978), 223. i •2 Glatch, J. L., Kirkland, J. J., Squire, K. M., and Miner, J. M.; J. Chromatgography, 199, (1980), 57. 4...assuming non retained peaks elute at 1 minute). This produces 3 solvents of approximately the same strengths bnt greatly differing selectivities. Once

Sensitivity field distributions for segmental bioelectrical impedance analysis based on real human anatomy

NASA Astrophysics Data System (ADS)

Danilov, A. A.; Kramarenko, V. K.; Nikolaev, D. V.; Rudnev, S. G.; Salamatova, V. Yu; Smirnov, A. V.; Vassilevski, Yu V.

2013-04-01

In this work, an adaptive unstructured tetrahedral mesh generation technology is applied for simulation of segmental bioimpedance measurements using high-resolution whole-body model of the Visible Human Project man. Sensitivity field distributions for a conventional tetrapolar, as well as eight- and ten-electrode measurement configurations are obtained. Based on the ten-electrode configuration, we suggest an algorithm for monitoring changes in the upper lung area.

LED-pumped Alexandrite laser oscillator and amplifier

NASA Astrophysics Data System (ADS)

Pichon, Pierre; Blanchot, Jean-Philippe; Balembois, François; Druon, Frédéric; Georges, Patrick

2018-02-01

In this paper, we report the first LED-pumped transition-metal-doped laser oscillator and amplifier based on an alexandrite crystal (Cr3+:BeAl2O4). A Ce:YAG luminescent concentrator illuminated by blue LEDs is used to reach higher pump powers than with LEDs alone. The luminescent 200-mm-long-composit luminescent concentrator involving 2240 LEDs can delivers up to 268 mJ for a peak irradiance of 8.5 kW/cm2. In oscillator configuration, an LED-pumped alexandrite laser delivering an energy of 2.9 mJ at 748 nm in free running operation is demonstrated. In the cavity, we measured a double pass small signal gain of 1.28, in good agreement with numerical simulations. As amplifier, the system demonstrated to boost a CW Ti:sapphire laser by a factor of 4 at 750 nm in 8 passes with a large tuning range from 710 nm to 800 nm.

Blade row dynamic digital compressor program. Volume 1: J85 clean inlet flow and parallel compressor models

NASA Technical Reports Server (NTRS)

Tesch, W. A.; Steenken, W. G.

1976-01-01

The results are presented of a one-dimensional dynamic digital blade row compressor model study of a J85-13 engine operating with uniform and with circumferentially distorted inlet flow. Details of the geometry and the derived blade row characteristics used to simulate the clean inlet performance are given. A stability criterion based upon the self developing unsteady internal flows near surge provided an accurate determination of the clean inlet surge line. The basic model was modified to include an arbitrary extent multi-sector parallel compressor configuration for investigating 180 deg 1/rev total pressure, total temperature, and combined total pressure and total temperature distortions. The combined distortions included opposed, coincident, and 90 deg overlapped patterns. The predicted losses in surge pressure ratio matched the measured data trends at all speeds and gave accurate predictions at high corrected speeds where the slope of the speed lines approached the vertical.

Dust grain resonant capture: A statistical study

NASA Technical Reports Server (NTRS)

Marzari, F.; Vanzani, V.; Weidenschilling, S. J.

1993-01-01

A statistical approach, based on a large number of simultaneous numerical integrations, is adopted to study the capture in external mean motion resonances with the Earth of micron size dust grains perturbed by solar radiation and wind forces. We explore the dependence of the resonant capture phenomenon on the initial eccentricity e(sub 0) and perihelion argument w(sub 0) of the dust particle orbit. The intensity of both the resonant and dissipative (Poynting-Robertson and wind drag) perturbations strongly depends on the eccentricity of the particle while the perihelion argument determines, for low inclination, the mutual geometrical configuration of the particle's orbit with respect to the Earth's orbit. We present results for three j:j+1 commensurabilities (2:3, 4:5 and 6:7) and also for particle sizes s = 15, 30 microns. This study extends our previous work on the long term orbital evolution of single dust particles trapped into resonances with the Earth.

Spectroscopy of Highly Charged Tin Ions for AN Extreme Ultraviolet Light Source for Lithography

NASA Astrophysics Data System (ADS)

Torretti, Francesco; Windberger, Alexander; Ubachs, Wim; Hoekstra, Ronnie; Versolato, Oscar; Ryabtsev, Alexander; Borschevsky, Anastasia; Berengut, Julian; Crespo Lopez-Urrutia, Jose

2017-06-01

Laser-produced tin plasmas are the prime candidates for the generation of extreme ultraviolet (EUV) light around 13.5 nm in nanolithographic applications. This light is generated primarily by atomic transitions in highly charged tin ions: Sn^{8+}-Sn^{14+}. Due to the electronic configurations of these charge states, thousands of atomic lines emit around 13.5 nm, clustered in a so-called unresolved transition array. As a result, accurate line identification becomes difficult in this regime. Nevertheless, this issue can be circumvented if one turns to the optical: with far fewer atomic states, only tens of transitions take place and the spectra can be resolved with far more ease. We have investigated optical emission lines in an electron-beam-ion-trap (EBIT), where we managed to charge-state resolve the spectra. Based on this technique and on a number of different ab initio techniques for calculating the level structure, the optical spectra could be assigned [1,2]. As a conclusion the assignments of EUV transitions in the literature require corrections. The EUV and optical spectra are measured simultaneously in the controlled conditions of the EBIT as well as in a droplet-based laser-produced plasma source providing information on the contribution of Sn^{q+} charge states to the EUV emission. [1] A. Windberger, F. Torretti, A. Borschevsky, A. Ryabtsev, S. Dobrodey, H. Bekker, E. Eliav, U. Kaldor, W. Ubachs, R. Hoekstra, J.R. Crespo Lopez-Urrutia, O.O. Versolato, Analysis of the fine structure of Sn^{11+} - Sn^{14+} ions by optical spectroscopy in an electron beam ion trap, Phys. Rev. A 94, 012506 (2016). [2] F. Torretti, A. Windberger, A. Ryabtsev, S. Dobrodey, H. Bekker, W. Ubachs, R. Hoekstra, E.V. Kahl, J.C. Berengut, J.R. Crespo Lopez-Urrutia, O.O. Versolato, Optical spectroscopy of complex open 4d-shell ions Sn^{7+} - Sn^{10+}, arXiv:1612.00747

Palladium configuration dependence of hydrogen detection sensitivity based on graphene FET for breath analysis

NASA Astrophysics Data System (ADS)

Sakamoto, Yuri; Uemura, Kohei; Ikuta, Takashi; Maehashi, Kenzo

2018-04-01

We have succeeded in fabricating a hydrogen gas sensor based on palladium-modified graphene field-effect transistors (FETs). The negative-voltage shift in the transfer characteristics was observed with exposure to hydrogen gas, which was explained by the change in work function. The hydrogen concentration dependence of the voltage shift was investigated using graphene FETs with palladium deposited by three different evaporation processes. The results indicate that the hydrogen detection sensitivity of the palladium-modified graphene FETs is strongly dependent on the palladium configuration. Therefore, the palladium-modified graphene FET is a candidate for breath analysis.

Quasi-CW 110 kW AlGaAs Laser Diode Array Module for Inertial Fusion Energy Laser Driver

NASA Astrophysics Data System (ADS)

Kawashima, Toshiyuki; Kanzaki, Takeshi; Matsui, Ken; Kato, Yoshinori; Matsui, Hiroki; Kanabe, Tadashi; Yamanaka, Masanobu; Nakatsuka, Masahiro; Izawa, Yasukazu; Nakai, Sadao; Miyamoto, Masahiro; Kan, Hirofumi; Hiruma, Teruo

2001-12-01

We have successfully demonstrated a large aperture 803 nm AlGaAs diode laser module as a pump source for a 1053 nm, 10 J output Nd:glass slab laser amplifier for diode-pumped solid-state laser (DPSSL) fusion driver. Detailed performance results of the laser diode module are presented, including bar package and stack configuration, and their thermal design and analysis. A sufficiently low thermal impedance of the stack was realized by combining backplane liquid cooling configuration with modular bar package architecture. Total peak power of 110 kW and electrical to optical conversion efficiency of 46% were obtained from the module consisting of a total of 1000 laser diode bars. A peak intensity of 2.6 kW/cm2 was accomplished across an emitting area of 418 mm× 10 mm. Currently, this laser diode array module with a large two-dimensional aperture is, to our knowledge, the only operational pump source for the high output energy DPSSL.

30 CFR 715.14 - Backfilling and grading.

Code of Federal Regulations, 2011 CFR

2011-07-01

... configuration and the outslopes of the plateau shall not exceed 1v:2h, except where engineering data... land use or may result in additional erosion and sedimentation. (j) Covering coal and acid-forming...

Characteristic Analysis Light Intensity Sensor Based On Plastic Optical Fiber At Various Configuration

NASA Astrophysics Data System (ADS)

Arifin, A.; Lusiana; Yunus, Muhammad; Dewang, Syamsir

2018-03-01

This research discusses the light intensity sensor based on plastic optical fiber. This light intensity sensor is made of plastic optical fiber consisting of two types, namely which is cladding and without cladding. Plastic optical fiber used multi-mode step-index type made of polymethyl metacrylate (PMMA). The infrared LED emits light into the optical fiber of the plastic and is subsequently received by the phototransistor to be converted to an electric voltage. The sensor configuration is made with three models: straight configuration, U configuration and gamma configuration with cladding and without cladding. The measured light source uses a 30 Watt high power LED with a light intensity of 0 to 10 Klux. The measured light intensity will affect the propagation of light inside the optical fiber sensor. The greater the intensity of the measured light, the greater the output voltage that is read on the computer. The results showed that the best optical fiber sensor characteristics were obtained in U configuration. Sensors with U-configuration without cladding had the best sensitivity and resolution values of 0.0307 volts/Klux and 0.0326 Klux. The advantages of this measuring light intensity based on the plastic optical fiber instrument are simple, easy-to-make operational systems, low cost, high sensitivity and resolution.

Characterization of Noble Gas Ion Beam Fabricated Single Molecule Nanopore Detectors

NASA Astrophysics Data System (ADS)

Rollings, Ryan; Ledden, Bradley; Shultz, John; Fologea, Daniel; Li, Jiali; Chervinsky, John; Golovchenko, Jene

2006-03-01

Nanopores fabricated with low energy noble gas ion beams in a silicon nitride membrane can be employed as the fundamental element of single biomolecule detection and characterization devices [1,2]. With the help of X-ray Photoelectron Spectroscopy (XPS) and Rutherford Backscattering (RBS), we demonstrate that the electrical noise properties, and hence ultimate sensitivity of nanopore single molecule detectors depends on ion beam species and nanopore annealing conditions. .1. Li, J., D. Stein, C. McMullan, D. Branton, M.J. Aziz, and J.A. Golovchenko, Ion-beam sculpting at nanometre length scales. Nature, 2001. 412(12 July): p. 166-169. 2. Li, J., M. Gershow, D. Stein, E. Brandin, and J.A. Golovchenko, DNA Molecules and Configurations in a Solid-state Nanopore Microscope. Nature Materials, 2003. 2: p. 611-615.

NASA/Navy life/cruise fan preliminary design report

NASA Technical Reports Server (NTRS)

1975-01-01

Preliminary design studies were performed to define a turbotip lift/cruise fan propulsion system for a Navy multimission aircraft. The fan is driven by the exhausts of the YJ97-GE-100 turbojet or a 20 percent Growth J97 configuration as defined during the studies. The LCF459 fan configuration defined has a tip diameter of 1.50 meters (59.0 inches) and develops a design point thrust of 75,130 N (16,890 lbs) at a fan pressure ratio of 1.319. The fan has an estimated weight of 386 kg (850 lbs). Trade studies performed to define the selected configuration are described.

100 J UV glass laser for dynamic compression research

NASA Astrophysics Data System (ADS)

Zweiback, J.; Fochs, S. F.; Bromage, J.; Broege, D.; Cuffney, R.; Currier, Z.; Dorrer, C.; Ehrich, B.; Engler, J.; Guardalben, M.; Kephalos, N.; Marozas, J.; Roides, R.; Zuegel, J.

2017-02-01

A frequency tripled, Nd:Glass laser has been constructed and installed at the Dynamic Compression Sector located at the Advanced Photon Source. This 100-J laser will be used to drive shocks in condensed matter which will then be interrogated by the facility x-ray beam. The laser is designed for reliable operation, utilizing proven designs for all major subsystems. A fiber front-end provides arbitrarily shaped pulses to the amplifier chain. A diode-pumped Nd:glass regenerative amplifier is followed by a four-pass, flashlamp- pumped rod amplifier. The regenerative amplifier produces up to 20 mJ with better than 1% RMS stability. The passively multiplexed four-pass amplifier produces up to 2 J. The final amplifier uses a 15-cm Nd:glass disk amplifier in a six-pass configuration. Over 200 J of infrared energy is produced by the disk amplifier. A KDP Type-II/Type-II frequency tripler configuration, utilizing a dual tripler, converts the 1053-nm laser output to a wavelength of 351 nm and the ultraviolet beam is image relayed to the target chamber. Output energy stability is better than 3%. Smoothing by Spectral Dispersion and polarization smoothing have been optimized to produce a highly uniform focal spot. A distributed phase plate and aspheric lens produce a farfield spot with a measured uniformity of 8.2% RMS. Custom control software collects all data and provides the operator an intuitive interface to operate and maintain the laser.

Analysis of Asymmetry by a Slide-Vector.

ERIC Educational Resources Information Center

Zielman, Berrie; Heiser, Willem J.

1993-01-01

An algorithm based on the majorization theory of J. de Leeuw and W. J. Heiser is presented for fitting the slide-vector model. It views the model as a constrained version of the unfolding model. A three-way variant is proposed, and two examples from market structure analysis are presented. (SLD)

Finite element analysis of history-dependent damage in time-dependent fracture mechanics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krishnaswamy, P.; Brust, F.W.; Ghadiali, N.D.

1993-11-01

The demands for structural systems to perform reliably under both severe and changing operating conditions continue to increase. Under these conditions time-dependent straining and history-dependent damage become extremely important. This work focuses on studying creep crack growth using finite element (FE) analysis. Two important issues, namely, (1) the use of history-dependent constitutive laws, and (2) the use of various fracture parameters in predicting creep crack growth, have both been addressed in this work. The constitutive model used here is the one developed by Murakami and Ohno and is based on the concept of a creep hardening surface. An implicit FEmore » algorithm for this model was first developed and verified for simple geometries and loading configurations. The numerical methodology developed here has been used to model stationary and growing cracks in CT specimens. Various fracture parameters such as the C[sub 1], C[sup *], T[sup *], J were used to compare the numerical predictions with experimental results available in the literature. A comparison of the values of these parameters as a function of time has been made for both stationary and growing cracks. The merit of using each of these parameters has also been discussed.« less

Stress history and fracture pattern in fault-related folds based on limit analysis: application to the Sub-Andean thrust belt of Bolivia

NASA Astrophysics Data System (ADS)

Barbe, Charlotte; Leroy, Yves; Ben Miloud, Camille

2017-04-01

A methodology is proposed to construct the stress history of a complex fault-related fold in which the deformation mechanisms are essentially frictional. To illustrate the approach, fours steps of the deformation of an initially horizontally layered sand/silicone laboratory experiment (Driehaus et al., J. of Struc. Geol., 65, 2014) are analysed with the kinematic approach of limit analysis (LA). The stress, conjugate to the virtual velocity gradient in the sense of mechanicam power, is a proxy for the true statically admmissible stress field which prevailed over the structure. The material properties, friction angles and cohesion, including their time evolution are selected such that the deformation pattern predicted by the LA is consistent with the two main thrusting events, the first forward and the second backward once the layers have sufficiently rotated. The fractures associated to the stress field determined at each step are convected on today configuration to define the complete pattern which should be observed. The end results are presented along virtual vertical wells and could be used within the oil industry at an early phase of exploration to prepare drealing operations.

Computer-based classification of bacteria species by analysis of their colonies Fresnel diffraction patterns

NASA Astrophysics Data System (ADS)

Suchwalko, Agnieszka; Buzalewicz, Igor; Podbielska, Halina

2012-01-01

In the presented paper the optical system with converging spherical wave illumination for classification of bacteria species, is proposed. It allows for compression of the observation space, observation of Fresnel patterns, diffraction pattern scaling and low level of optical aberrations, which are not possessed by other optical configurations. Obtained experimental results have shown that colonies of specific bacteria species generate unique diffraction signatures. Analysis of Fresnel diffraction patterns of bacteria colonies can be fast and reliable method for classification and recognition of bacteria species. To determine the unique features of bacteria colonies diffraction patterns the image processing analysis was proposed. Classification can be performed by analyzing the spatial structure of diffraction patterns, which can be characterized by set of concentric rings. The characteristics of such rings depends on the bacteria species. In the paper, the influence of basic features and ring partitioning number on the bacteria classification, is analyzed. It is demonstrated that Fresnel patterns can be used for classification of following species: Salmonella enteritidis, Staplyococcus aureus, Proteus mirabilis and Citrobacter freundii. Image processing is performed by free ImageJ software, for which a special macro with human interaction, was written. LDA classification, CV method, ANOVA and PCA visualizations preceded by image data extraction were conducted using the free software R.

Space shuttle development Motor No. 9 (DM-9), volume 1

NASA Technical Reports Server (NTRS)

Garecht, Diane M.

1990-01-01

The results obtained during the December 23, 1987 static firing of the DM-9 test article are presented. The DM-9 full-scale static test article employed redesigned solid rocket motor (RSRM) field joint capture feature hardware with J-seal insulation configuration, and nozzle-to-case joint radial bolt design with bonded insulation configuration. The nozzle incorporated RSRM components, including a thicker cowl with involuted outer boot ring. The nozzle employed redundant and verifiable seals in all five joints, and room temperature vulcanization backfill in three joints. With very few exceptions, the DM-9 test article was flight configuration. The test was conducted under extreme weather conditions: temperature of 25 F and wind at 15 to 20 mph. Ballistics performance values were within specification requirements. The RSRM field joint (J-seal) insulation configuration functioned as predicted with no indication of hot gases reaching the capture feature O-rings. There was a blowhole in the polysulfide adhesive in the nozzle-to-case joint, but no evidence of hot gases past the wiper O-ring. Nozzle design changes appeared to perform nominally, with the exception of the outer boot ring, which suffered partial structural breakup late in the test. Field joint heaters maintained the controlling resistance temperature device temperature within the specified requirements during heater operation. The thrust vector control system operated properly. The redesigned water deluge system, temperature conditioning equipment, and other test support equipment performed as planned.

Safety diagnosis: are we doing a good job?

PubMed

Park, Peter Y; Sahaji, Rajib

2013-03-01

Collision diagnosis is the second step in the six-step road safety management process described in the AASHTO Highway Safety Manual (HSM). Diagnosis is designed to identify a dominant or abnormally high proportion of particular collision configurations (e.g., rear end, right angle, etc.) at a target location. The primary diagnosis method suggested in the HSM is descriptive data analysis. This type of analysis relies on, for example, pie charts, histograms, and/or collision diagrams. Using location specific collision data (e.g., collision frequency per collision configuration for a target location), safety engineers identify (the most) frequent collision configurations. Safety countermeasures are then likely to concentrate on preventing the selected collision configurations. Although its real-world application in engineering practice is limited, an additional collision diagnosis method, known as the beta-binomial (BB) test, is also presented as the secondary diagnosis tool in the HSM. The BB test compares the proportion of a particular collision configuration observed at one location with the proportion of the same collision configuration found at other reference locations which are similar to the target location in terms of selected traffic and roadway characteristics (e.g., traffic volume, traffic control, and number of lanes). This study compared the outcomes obtained from descriptive data analysis and the BB test, and investigates two questions: (1) Do descriptive data analysis and the BB tests produce the same results (i.e., do they select the same collision configurations at the same locations)? and (2) If the tests produce different results, which result should be adopted in engineering practice? This study's analysis was based on a sample of the most recent five years (2005-2009) of collision and roadway configuration data for 143 signalized intersections in the City of Saskatoon, Saskatchewan. The study results show that the BB test's role in diagnosing safety concerns in road safety engineering projects such as safety review projects for existing roadways may be just as important as the descriptive data analysis method. Copyright © 2012 Elsevier Ltd. All rights reserved.

Exergy Analysis of Rocket Systems

NASA Technical Reports Server (NTRS)

Gilbert, Andrew; Mesmer, Bryan; Watson, Michael D.

2015-01-01

Exergy is defined as the useful work available from a system in a specified environment. Exergy analysis allows for comparison between different system designs, and allows for comparison of subsystem efficiencies within system designs. The proposed paper explores the relationship between the fundamental rocket equation and an exergy balance equation. A previously derived exergy equation related to rocket systems is investigated, and a higher fidelity analysis will be derived. The exergy assessments will enable informed, value-based decision making when comparing alternative rocket system designs, and will allow the most efficient configuration among candidate configurations to be determined.

Prediction of gas-liquid two-phase flow regime in microgravity

NASA Technical Reports Server (NTRS)

Lee, Jinho; Platt, Jonathan A.

1993-01-01

An attempt is made to predict gas-liquid two-phase flow regime in a pipe in a microgravity environment through scaling analysis based on dominant physical mechanisms. Simple inlet geometry is adopted in the analysis to see the effect of inlet configuration on flow regime transitions. Comparison of the prediction with the existing experimental data shows good agreement, though more work is required to better define some physical parameters. The analysis clarifies much of the physics involved in this problem and can be applied to other configurations.

Ising Model on Tangled Chain, Some Thermodynamic Properties

NASA Astrophysics Data System (ADS)

Mejdani, R.

1996-09-01

In this paper we consider an Ising model on tangled chain, where some additional bonds compared to a pure Ising chain are presented. To understand the behavior of this system and the competition between ferromagnetic bonds J along the chain and antiferromagnetic bonds J' across the chain, we have studied in detail analytically and iteratively some of the thermodynamic quantities. Particularly interesting is, in the zero-field and zero-temperature limit, the behavior of the magnetization and the susceptibility closely related to the ground-state configurations and their degeneracies. This degeneracy, presented at the condition J' ≤ -J between J and J', explains, also, the existence of nonzero entropy at zero temperature. This model applied as a lattice gas model defined on a tangled chain could be also useful for the experimental investigations in studying the saturation curves for the enzyme kinetics or the melting curves for DNA-denaturation.

PKDE4J: Entity and relation extraction for public knowledge discovery.

PubMed

Song, Min; Kim, Won Chul; Lee, Dahee; Heo, Go Eun; Kang, Keun Young

2015-10-01

Due to an enormous number of scientific publications that cannot be handled manually, there is a rising interest in text-mining techniques for automated information extraction, especially in the biomedical field. Such techniques provide effective means of information search, knowledge discovery, and hypothesis generation. Most previous studies have primarily focused on the design and performance improvement of either named entity recognition or relation extraction. In this paper, we present PKDE4J, a comprehensive text-mining system that integrates dictionary-based entity extraction and rule-based relation extraction in a highly flexible and extensible framework. Starting with the Stanford CoreNLP, we developed the system to cope with multiple types of entities and relations. The system also has fairly good performance in terms of accuracy as well as the ability to configure text-processing components. We demonstrate its competitive performance by evaluating it on many corpora and found that it surpasses existing systems with average F-measures of 85% for entity extraction and 81% for relation extraction. Copyright © 2015 Elsevier Inc. All rights reserved.

Effect of gadolinium incorporation on the structure and luminescence properties of niobium-based materials.

PubMed

Oliveira, Lidia Resende; Moscardini, Susane Bonamin; Molina, Eduardo Ferreira; Nassar, Eduardo José; Verelst, Marc; Rocha, Lucas Alonso

2018-06-08

In this work, we have investigated how the concentration of Gd 3+ ions affects the structural and luminescent properties of niobium oxide-based matrices doped with Eu 3+ ions obtained by the adapted non-hydrolytic sol-gel route. X-ray diffractograms revealed that increasing the concentration of Gd 3+ ions favored the onset of the Gd 2 O 3 structure decreasing the GdNbO 4 phase. The excitation spectra (λ em  = 613 nm) presented bands corresponding to the 7 F 0  →  5 L J transitions (L = D, G, and L, where J = 0-7), attributed to the Eu 3+ ions, and a broad band at 270 nm, assigned to the charge transfer of the [Formula: see text] group. The emission spectra contained bands refer to the 5 D 0  →  7 F J internal configuration transitions (J = 0, 1, 2, 3, and 4). Finally, the CIE chromaticity coordinates met the standard for the color red established by the National Television Standard Committee (NTSC).

A New Non-LTE Model based on Super Configurations

NASA Astrophysics Data System (ADS)

Bar-Shalom, A.; Klapisch, M.

1996-11-01

Non-LTE effects are vital for the simulation of radiation in hot plasmas involving even medium Z materials. However, the exceedingly large number of atomic energy levels forbids using a detailed collisional radiative model on-line in the hydrodynamic simulations. For this purpose, greatly simplified models are required. We implemented recently Busquet's model(M. Busquet, Phys. Fluids B, 5, 4191 (1993)) in NRL's RAD2D Hydro code in conservative form (M. Klapisch et al., Bull. Am. Phys. Soc., 40, 1806 (1995), and poster at this meeting.). This model is quick and the results make sense, but in the absence of precisely defined experiments, it is difficult to asses its accuracy. We present here a new collisional radiative model based on superconfigurations( A. Bar-Shalom, J. Oreg, J. F. Seely, U. Feldman, C. M. Brown, B. A. Hammel, R. W. Lee and C. A. Back, Phys. Rev. E, 52, 6686 (1995).), intended to be a benchmark for approximate models used in hydro-codes. It uses accurate rates from the HULLAC Code. Results for various elements will be presented and compared with RADIOM.

Transport Simulations for Fast Ignition on NIF

NASA Astrophysics Data System (ADS)

Strozzi, D. J.; Tabak, M.; Grote, D. P.; Town, R. P. J.; Kemp, A. J.

2009-11-01

Calculations of the transport and deposition of a relativistic electron beam into fast-ignition fuel configurations are presented. The hybrid PIC code LSP is used, run in implicit mode and with fluid background particles. The electron beam distribution is chosen based on explicit PIC simulations of the short-pulse LPI. These generally display two hot-electron temperatures, one close to the ponderomotive scaling and one that is much lower. Fast-electron collisions utilize the formulae of J. R. Davies [S. Atzeni et al., Plasma Phys. Controlled Fusion 51 (2009)], and are done with a conservative, relativistic grid-based method similar to Lemons et al., J. Comput. Phys. 228 (2009). We include energy loss off both bound and free electrons in partially-ionized media (such as a gold cone), and have started to use realistic ionization and non-ideal EOS models. We have found the fractional energy coupling into the dense fuel is higher for CD than DT targets, due to the enhanced resistivity and resulting magnetic fields. The coupling enhancement due to magnetic fields and beam characteristics (such as angular spectrum) will be quantified.

Aerodynamic preliminary analysis system 2. Part 2: User's manuals

NASA Technical Reports Server (NTRS)

Divan, P.

1981-01-01

An aerodynamic analysis system based on potential theory at subsonic/supersonic speeds and impact type finite element solutions at hypersonic conditions is described. Three dimensional configurations having multiple nonplanar surfaces of arbitrary planform and bodies of noncircular contour may be analyzed. Static, rotary, and control longitudinal and lateral directional chracteristics may be generated. The analysis has been implemented on a time sharing system in conjunction with an input tablet digitizer and an interactive graphics input/output display and editing terminal to maximize its responsiveness to the preliminary analysis problem. Typical simulation indicates that program provides an efficient analysis for systematically performing various aerodynamic configuration tradeoff and evaluation studies.

Aerodynamic preliminary analysis system 2. Part 1: Theory

NASA Technical Reports Server (NTRS)

Bonner, E.; Clever, W.; Dunn, K.

1991-01-01

An aerodynamic analysis system based on potential theory at subsonic and/or supersonic speeds and impact type finite element solutions at hypersonic conditions is described. Three dimensional configurations having multiple nonplanar surfaces of arbitrary planform and bodies of noncircular contour may be analyzed. Static, rotary, and control longitudinal and lateral directional characteristics may be generated. The analysis was implemented on a time sharing system in conjunction with an input tablet digitizer and an interactive graphics input/output display and editing terminal to maximize its responsiveness to the preliminary analysis problem. The program provides an efficient analysis for systematically performing various aerodynamic configuration tradeoff and evaluation studies.

Theoretical calculations of rotationally inelastic collisions of He with NaK(A {sup 1}Σ{sup +}): Transfer of population, orientation, and alignment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malenda, R. F.; Price, T. J.; Stevens, J.

2015-06-14

We have performed extensive calculations to investigate thermal energy, rotationally inelastic collisions of NaK (A{sup 1}Σ{sup +}) with He. We determined a potential energy surface using a multi-reference configuration interaction wave function as implemented by the GAMESS electronic structure code, and we have performed coupled channel scattering calculations using the Arthurs and Dalgarno formalism. We also calculate the Grawert coefficients B{sub λ}(j, j′) for each j → j′ transition. These coefficients are used to determine the probability that orientation and alignment are preserved in collisions taking place in a cell environment. The calculations include all rotational levels with j ormore » j′ between 0 and 50, and total (translational and rotational) energies in the range 0.0002–0.0025 a.u. (∼44–550 cm{sup −1}). The calculated cross sections for transitions with even values of Δj tend to be larger than those for transitions with odd Δj, in agreement with the recent experiments of Wolfe et al. (J. Chem. Phys. 134, 174301 (2011)). The calculations of the energy dependence of the cross sections and the calculations of the fraction of orientation and alignment preserved in collisions also exhibit distinctly different behaviors for odd and even values of Δj. The calculations also indicate that the average fraction of orientation or alignment preserved in a transition becomes larger as j increases. We interpret this behavior using the semiclassical model of Derouard, which also leads to a simple way of visualizing the distribution of the angles between the initial and final angular momentum vectors j and j′. Finally, we compare the exact quantum results for j → j′ transitions with results based on the simpler, energy sudden approximation. That approximation is shown to be quite accurate.« less

A graph-based system for network-vulnerability analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swiler, L.P.; Phillips, C.

1998-06-01

This paper presents a graph-based approach to network vulnerability analysis. The method is flexible, allowing analysis of attacks from both outside and inside the network. It can analyze risks to a specific network asset, or examine the universe of possible consequences following a successful attack. The graph-based tool can identify the set of attack paths that have a high probability of success (or a low effort cost) for the attacker. The system could be used to test the effectiveness of making configuration changes, implementing an intrusion detection system, etc. The analysis system requires as input a database of common attacks,more » broken into atomic steps, specific network configuration and topology information, and an attacker profile. The attack information is matched with the network configuration information and an attacker profile to create a superset attack graph. Nodes identify a stage of attack, for example the class of machines the attacker has accessed and the user privilege level he or she has compromised. The arcs in the attack graph represent attacks or stages of attacks. By assigning probabilities of success on the arcs or costs representing level-of-effort for the attacker, various graph algorithms such as shortest-path algorithms can identify the attack paths with the highest probability of success.« less

Configuration development study of the OSU 1 hypersonic research vehicle

NASA Technical Reports Server (NTRS)

Stein, Matthew D.; Frankhauser, Chris; Zee, Warner; Kosanchick, Melvin, III; Nelson, Nick; Hunt, William

1993-01-01

In an effort to insure the future development of hypersonic cruise aircraft, the possible vehicle configurations were examined to develop a single-stage-to-orbit hypersonic research vehicle (HRV). Based on the needs of hypersonic research and development, the mission goals and requirements are determined. A body type is chosen. Three modes of propulsion and two liquid rocket fuels are compared, followed by the optimization of the body configuration through aerodynamic, weight, and trajectory studies. A cost analysis is included.

Value-centric design architecture based on analysis of space system characteristics

NASA Astrophysics Data System (ADS)

Xu, Q.; Hollingsworth, P.; Smith, K.

2018-03-01

Emerging design concepts such as miniaturisation, modularity, and standardisation, have contributed to the rapid development of small and inexpensive platforms, particularly cubesats. This has been stimulating an upcoming revolution in space design and development, leading satellites into the era of "smaller, faster, and cheaper". However, the current requirement-centric design philosophy, focused on bespoke monolithic systems, along with the associated development and production process does not inherently fit with the innovative modular, standardised, and mass-produced technologies. This paper presents a new categorisation, characterisation, and value-centric design architecture to address this need for both traditional and novel system designs. Based on the categorisation of system configurations, a characterisation of space systems, comprised of duplication, fractionation, and derivation, is proposed to capture the overall system configuration characteristics and promote potential hybrid designs. Complying with the definitions of the system characterisation, mathematical mapping relations between the system characterisation and the system properties are described to establish the mathematical foundation of the proposed value-centric design methodology. To illustrate the methodology, subsystem reliability relationships are therefore analysed to explore potential system configurations in the design space. The results of the applications of system characteristic analysis clearly show that the effects of different configuration characteristics on the system properties can be effectively analysed and evaluated, enabling the optimization of system configurations.

Investigation of field emission properties of laser irradiated tungsten

NASA Astrophysics Data System (ADS)

Akram, Mahreen; Bashir, Shazia; Jalil, Sohail Abdul; Rafique, Muhammad Shahid; Hayat, Asma; Mahmood, Khaliq

2018-02-01

Nd:YAG laser irradiation of Tungsten (W) has been performed in air at atmospheric pressure for four laser fluences ranging from 130 to 500 J/cm2. Scanning electron microscope analysis revealed the formation of micro and nanoscale surface features including cones, grains, mounds and pores. Field emission (FE) studies have been performed in a planar diode configuration under ultra-high vacuum conditions by recording I- V characteristics and plotting corresponding electric field ( E) versus emission current density ( J). The Fowler-Nordheim (FN) plots are found to be linear confirming the quantum mechanical tunneling phenomena for the structured targets. The irradiated samples at different fluences exhibit a turn-on field, field enhancement factor β and a maximum current density ranging from 5 to 8.5 V/µm, 1300 to 3490 and 107 to 350 µA/cm2, respectively. The difference in the FE properties is attributed to the variation in the nature and density of the grown structures at different fluences.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jarrott, L. C.; McGuffey, C.; Beg, F. N.

Fast electron transport and spatial energy deposition are investigated in integrated cone-guided Fast Ignition experiments by measuring fast electron induced copper K-shell emission using a copper tracer added to deuterated plastic shells with a geometrically reentrant gold cone. Experiments were carried out at the Laboratory for Laser Energetics on the OMEGA/OMEGA-EP Laser where the plastic shells were imploded using 54 of the 60 OMEGA60 beams (3ω, 20 kJ), while the high intensity OMEGA-EP (BL2) beam (1 ω, 10 ps, 500 J, I peak > 10 19 W/cm 2) was focused onto the inner cone tip. Here, a retrograde analysis usingmore » the hybrid-PIC electron transport code, ZUMA, is performed to examine the sensitivity of the copper Kα spatial profile on the laser-produced fast electrons, facilitating the optimization of new target point designs and laser configurations to improve the compressed core areal density by a factor of 4 and the fast electron energy coupling by a factor of 3.5.« less

Cluster analysis based on dimensional information with applications to feature selection and classification

NASA Technical Reports Server (NTRS)

Eigen, D. J.; Fromm, F. R.; Northouse, R. A.

1974-01-01

A new clustering algorithm is presented that is based on dimensional information. The algorithm includes an inherent feature selection criterion, which is discussed. Further, a heuristic method for choosing the proper number of intervals for a frequency distribution histogram, a feature necessary for the algorithm, is presented. The algorithm, although usable as a stand-alone clustering technique, is then utilized as a global approximator. Local clustering techniques and configuration of a global-local scheme are discussed, and finally the complete global-local and feature selector configuration is shown in application to a real-time adaptive classification scheme for the analysis of remote sensed multispectral scanner data.

Turbulent Mixing of Primary and Secondary Flow Streams in a Rocket-Based Combined Cycle Engine

NASA Technical Reports Server (NTRS)

Cramer, J. M.; Greene, M. U.; Pal, S.; Santoro, R. J.; Turner, Jim (Technical Monitor)

2002-01-01

This viewgraph presentation gives an overview of the turbulent mixing of primary and secondary flow streams in a rocket-based combined cycle (RBCC) engine. A significant RBCC ejector mode database has been generated, detailing single and twin thruster configurations and global and local measurements. On-going analysis and correlation efforts include Marshall Space Flight Center computational fluid dynamics modeling and turbulent shear layer analysis. Potential follow-on activities include detailed measurements of air flow static pressure and velocity profiles, investigations into other thruster spacing configurations, performing a fundamental shear layer mixing study, and demonstrating single-shot Raman measurements.

Guidelines for Proof Test Analysis

NASA Technical Reports Server (NTRS)

Chell, G. G.; McClung, R. C.; Kuhlman, C. J.; Russell, D. A.; Garr, K.; Donnelly, B.

1999-01-01

These guidelines integrate state-of-the-art elastic-plastic fracture mechanics (EPFM) and proof test implementation issues into a comprehensive proof test analysis procedure in the form of a road map which identifies the types of data, fracture mechanics based parameters, and calculations needed to perform flaw screening and minimum proof load analyses of fracture critical components. Worked examples are presented to illustrate the application of the road map to proof test analysis. The state-of-the art fracture technology employed in these guidelines is based on the EPFM parameter, J, and a pictorial representation of a J fracture analysis, called the failure assessment diagram (FAD) approach. The recommended fracture technology is validated using finite element J results, and laboratory and hardware fracture test results on the nickel-based superalloy Inconel 718, the aluminum alloy 2024-T3511, and ferritic pressure vessel steels. In all cases the laboratory specimens and hardware failed by ductile mechanisms. Advanced proof test analyses involving probability analysis and multiple-cycle proof testing (MCPT) are addressed. Finally, recommendations are provided on how to account for the effects of the proof test overload on subsequent service fatigue and fracture behaviors.

The Last Millennium Reanalysis: Improvements to proxies and proxy modeling

NASA Astrophysics Data System (ADS)

Tardif, R.; Hakim, G. J.; Emile-Geay, J.; Noone, D.; Anderson, D. M.

2017-12-01

The Last Millennium Reanalysis (LMR) employs a paleoclimate data assimilation (PDA) approach to produce climate field reconstructions (CFRs). Here, we focus on two key factors in PDA generated CFRs: the set of assimilated proxy records and forward models (FMs) used to estimate proxies from climate model output. In the initial configuration of the LMR [Hakim et al., 2016], the proxy dataset of [PAGES2k Consortium, 2013] was used, along with univariate linear FMs calibrated against annually-averaged 20th century temperature datasets. In an updated configuration, proxy records from the recent dataset [PAGES2k Consortium, 2017] are used, while a hierarchy of statistical FMs are tested: (1) univariate calibrated on annual temperature as in the initial configuration, (2) univariate against temperature as in (1) but calibration performed using expert-derived seasonality for individual proxy records, (3) as in (2) but expert proxy seasonality replaced by seasonal averaging determined objectively as part of the calibration process, (4) linear objective seasonal FMs as in (3) but objectively selecting relationships calibrated either on temperature or precipitation, and (5) bivariate linear models calibrated on temperature and precipitation with objectively-derived seasonality. (4) and (5) specifically aim at better representing the physical drivers of tree ring width proxies. Reconstructions generated using the CCSM4 Last Millennium simulation as an uninformed prior are evaluated against various 20th century data products. Results show the benefits of using the new proxy collection, particularly on the detrended global mean temperature and spatial patterns. The positive impact of using proper seasonality and temperature/moisture sensitivities for tree ring width records is also notable. This updated configuration will be used for the first generation of LMR-generated CFRs to be publicly released. These also provide a benchmark for future efforts aimed at evaluating the impact of additional proxy records and/or more sophisticated physically-based forward models. References: Hakim, G. J., and co-authors (2016), J. Geophys. Res. Atmos., doi:10.1002/2016JD024751 PAGES2K Consortium (2013), Nat. Geosci., doi:10.1038/ngeo1797 PAGES2k Consortium (2017), Sci. Data. doi:10.1038/sdata.2017.88

Theoretical Studies of Oxygen Reduction and Proton Transfer in SOFCs and Nerve Agents on Selected Surfaces

DTIC Science & Technology

2015-11-19

hand, the energy change for CO3 2- +O2→CO5 2- is calculated to be - 105.5 kJ/mol and -87.3 kJ/mol by B3LYP and CCSD(T), respectively. Similarly, the...formation energy of CO4 2- ( CO3 2- +1/2O2→CO4 2- ) is -9.8 kJ/mol and -5.4 kJ/mol by B3LYP and CCSD(T), respectively. All testing results have...This configuration is same as those in their crystal structures of bulk Li2CO3, Na2CO3, and K2CO3. In addition, the average bond length between alkali

The direct measurement of the 3 3P0-3 3P1 fine-structure interval and the gJ-factor of atomic silicon by laser magnetic resonance

NASA Technical Reports Server (NTRS)

Evenson, K. M.; Beltran-Lopez, V.; Ley-Koo, E.; Inguscio, M.

1984-01-01

The J - 1 fine structure interval and the g-factor of the 3P1 state have been determined with high precision in the present laser magnetic resonance measurements of the ground 3p2 3P multiplet of atomic Si. Delta-E(3P1-3P0) = 2,311,755.6(7) MHz, and gJ(3P1) = 1.500830(70). Single-configuration calculations of gJ for 3P1 and 3P2 yield a value for the latter which, at 1.501095, is noted to differ by an unexpectedly large margin from the experimental value.

Illustration of Ares I During Launch

NASA Technical Reports Server (NTRS)

2006-01-01

The NASA developed Ares rockets, named for the Greek god associated with Mars, will return humans to the moon and later take them to Mars and other destinations. In this early illustration, the Ares I is illustrated during lift off. Ares I is an inline, two-stage rocket configuration topped by the Orion crew vehicle and its launch abort system. With a primary mission of carrying four to six member crews to Earth orbit, Ares I may also use its 25-ton payload capacity to deliver resources and supplies to the International Space Station (ISS), or to 'park' payloads in orbit for retrieval by other spacecraft bound for the moon or other destinations. Ares I uses a single five-segment solid rocket booster, a derivative of the space shuttle solid rocket booster, for the first stage. A liquid oxygen/liquid hydrogen J-2X engine, derived from the J-2 engine used on the second stage of the Apollo vehicle, will power the Ares I second stage. Ares I can lift more than 55,000 pounds to low Earth orbit. The Ares I is subject to configuration changes before it is actually launched. This illustration reflects the latest configuration as of September 2006.

Illustration of Ares I Launch Vehicle With Call Outs

NASA Technical Reports Server (NTRS)

2006-01-01

Named for the Greek god associated with Mars, the NASA developed Ares launch vehicles will return humans to the moon and later take them to Mars and other destinations. This is an illustration of the Ares I with call outs. Ares I is an inline, two-stage rocket configuration topped by the Orion crew vehicle and its launch abort system. In addition to the primary mission of carrying crews of four to six astronauts to Earth orbit, Ares I may also use its 25-ton payload capacity to deliver resources and supplies to the International Space Station, or to 'park' payloads in orbit for retrieval by other spacecraft bound for the moon or other destinations. Ares I employs a single five-segment solid rocket booster, a derivative of the space shuttle solid rocket booster, for the first stage. A liquid oxygen/liquid hydrogen J-2X engine derived from the J-2 engine used on the Apollo second stage will power the Ares I second stage. The Ares I can lift more than 55,000 pounds to low Earth orbit. Ares I is subject to configuration changes before it is actually launched. This illustration reflects the latest configuration as of January 2007.

Time-frequency analysis of the bistatic acoustic scattering from a spherical elastic shell.

PubMed

Anderson, Shaun D; Sabra, Karim G; Zakharia, Manell E; Sessarego, Jean-Pierre

2012-01-01

The development of low-frequency sonar systems, using, for instance, a network of autonomous systems in unmanned vehicles, provides a practical means for bistatic measurements (i.e., when the source and receiver are widely separated) allowing for multiple viewpoints of the target of interest. Time-frequency analysis, in particular, Wigner-Ville analysis, takes advantage of the evolution time dependent aspect of the echo spectrum to differentiate a man-made target, such as an elastic spherical shell, from a natural object of the similar shape. A key energetic feature of fluid-loaded and thin spherical shell is the coincidence pattern, also referred to as the mid-frequency enhancement (MFE), that results from antisymmetric Lamb-waves propagating around the circumference of the shell. This article investigates numerically the bistatic variations of the MFE with respect to the monostatic configuration using the Wigner-Ville analysis. The observed time-frequency shifts of the MFE are modeled using a previously derived quantitative ray theory by Zhang et al. [J. Acoust. Soc. Am. 91, 1862-1874 (1993)] for spherical shell's scattering. Additionally, the advantage of an optimal array beamformer, based on joint time delays and frequency shifts is illustrated for enhancing the detection of the MFE recorded across a bistatic receiver array when compared to a conventional time-delay beamformer. © 2012 Acoustical Society of America.

ZEEMAN INVESTIGATIONS OF CURIUM-242

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hubbs, J.C.; Marrus, R.; Winocur, J.O.

The atomic-beam magnetic-resonance method has been used to investigate 163-day Cm/sup 242/. The spin of this even-even nuclide is found to be zero. Four low-lying electronlc energy levels are found and the Lande gfactors are measured to be g/sub J2/ = 2.561 plus or minus 0.003, g/sub J3/ 2.000 plus or minus 0.003, g/sub J4/ = 1.776 plus or minus 0.002, and g/sub J5/ = 1.671 plus or minus 0.003. No direct measurement can be made of the angular momenta of these levels, but other considerations contained in the text make highly probable the J values indicated in subscripts andmore » arising from the electronic configuration (5f)/sup 7/ (6d)/sup 1 (7s)/sup 2/. (auth)« less

Hadron molecules

NASA Astrophysics Data System (ADS)

Thomas, Gutsche; Tanja, Branz; Amand, Faessler; Ian, Woo Lee; Valery, E. Lyubovitskij

2010-09-01

We discuss a possible interpretation of the open charm mesons D*s0(2317), Ds1(2460) and the hidden charm mesons X(3872), Y(3940) and Y(4140) as hadron molecules. Using a phenomenological Lagrangian approach we review the strong and radiative decays of the D*s0(2317) and Ds1(2460) states. The X(3872) is assumed to consist dominantly of molecular hadronic components with an additional small admixture of a charmonium configuration. Determing the radiative (γJ/Ψ and γΨ(2s)) and strong (J/Ψ2π and J/Ψ3π) decay modes we show that the present experimental observation is consistent with the molecular structure assumption of the X(3872). Finally, we give evidence for molecular interpretations of the Y(3940) and Y(4140) related to the observed strong decay modes J/Ψ + ω or J/Ψ + varphi, respectively.

Diffusion in fractal wakes and convective thermoelectric flows

NASA Astrophysics Data System (ADS)

Vila, Teresa; Tellez, Jackson; Sanchez, Jesus Maria; Sotillos, Laura; Diez, Margarita; Redondo, Jose Manuel

2014-05-01

We calculate diffusion and scaling of the velocity ald vorticity in a thermoelectric driven heating and cooling experimental device in order to map the different transitions between two and three dimensional convection in an enclosure and complex driven flows. The size of the water tank is of 0.2 x 0.2 x 0.1 m and the heat sources or sinks can be regulated both in power and sign [1-3]. The thermal convective driven flows are generated by Seebeck and Peltier effects in 4 wall extended positions of 0.05 x 0.05 cm each. The parameter range of convective cell array varies strongly with the Topology of the boundary conditions. At present side heat fluxes are considered and estimated as a function of Rayleigh, Peclet and Nusselt numbers,[4-6] Visualizations are performed by PIV, Particle tracking and shadowgraph. Diffusion is measured in the transition from a homogeneous linearly stratified fluid to a cellular or layered structure by means of stirring. Patterns arise by setting up a convective flow generated by a buoyant heat flux [5,6]. The experiments described here investigate high Prandtl number mixing using brine and fresh water in order to form a density interface and low Prandtl number mixing with temperature gradients. Using ESS and selfsimilarity structures in the velocity and vorticity fieds and intermittency [2] that forms in the flow is related to mixing and stiring. The evolution of the mixing fronts are compared and the topological characteristics of the merging of the plumes and jets are examined for different configurations. We also present a detailed comparison of the evolution of RM and RT, Jets and Plumes in overall mixing. The relation between fractal analysis and spectral analysis can be very useful to determine the evolution of scales. Experimental and numerical results on the advance of a mixing or nonmixing front occurring at a density interface due to gravitational acceleration are analyzed considering the fractal and spectral structure of the fronts like removable plate experiments [7] for Rayleigh-Taylor flows. The evolution of the turbulent mixing layer and its complex configuration is studied taking into account the dependence on the initial modes at the early stages and its spectral, self-similar information [8,9]. Spectral and Fractal analysis on the images has been used in order to estimate dominant mixing structures as well as the dispersion relations of basic instabilities [2,10]. [1] Redondo J.M. (1992) Termodinámica de los procesos irreversibles, efectos termoeléctricos Rev. Termoelectricidad 2, 16-29.AIT.Pamplona. [2] Mahjoub O.B., Redondo J.M. and Babiano A.(2000) "Hyerarchy flux in nonhomogeneous flows" in Turbulent diffusion in the environment Eds. Redondo J.M. and Babiano A. 249-260. [3] Redondo J.M., Sanchez J.M. Pascual I. Noriega, G.F.(1995)."Thermoelectric regulation for electric cabinets".XVI International Conference in Thermoelectrics, 02-G20. Ed. V. Vedernikov. 456-468. St. Petersburg, Russia. [4] Kuramitsu, M.; Redondo, J.M.; Noriega, G. (2003) Measurements of anisotropy, thermoelectric behaviour and multi-fractal aspects of FeSi and of complex custom made TE materials Twenty-Second International Conference on Thermoelectric- ICT,IEEE, DOI:10.1109/ICT.2003.1287570, 541-545. [5] López González-Nieto, P., Cano, J. L. and Redondo, J. M., "Buoyant mixing processes generated in turbulent pluma arrays" in Experimental and Modelling Micrometeorology, Física de la Tierra, vol. 19, pp. 205-219, 2007. [6] Kimura R. and Iga, I. (1995) Bubble Convection in Mixing in Geophysical Flows Eds. Redondo J.M: and Metais, 35-51. Ed CIMNE, Barcelona. [7] Linden, P. F., Redondo, J. M. and Caulfield, C. P.: (1992), Advances in Compressible Turbulent Mixing, edited by W.P. Dannevik, A.C. Buckingham and C.E. Leith, Princenton University. [8] Nicolleau, F.C.G.A.; Cambon, C.; Redondo, J.M.; Vassilicos, J.C.; Reeks, M.; Nowakowski, A.F. (Eds.) New Approaches in Modeling Multiphase Flows and Dispersion in Turbulence, Fractual Methods and Synthetic Turbulence. ERCOFTAC Series, Vol. 18 1st Edition., 2011, 250 p. ISBN 978-94-007-2505-8 [9] F Ciuchi; L Sorriso-Valvo; A Mazzulla and J. M. Redondo (2009).Fractal aggregates evolution of methyl red in liquid crystal. European physical journal E.29 - 2,pp. 139 - 147.06/2009 . [10]Platonov A. Carrillo A. Matulka A, Sekula E., Grau J. Redondo J.M. and Tarquis A. (2008)Multifractal observations of eddies, oil spills and natural slicks in the ocean surface. Il Nuovo Cimento C 31,5-6, 861-880.

Overview of Sensitivity Analysis and Shape Optimization for Complex Aerodynamic Configurations

NASA Technical Reports Server (NTRS)

Newman, Perry A.; Newman, James C., III; Barnwell, Richard W.; Taylor, Arthur C., III; Hou, Gene J.-W.

1998-01-01

This paper presents a brief overview of some of the more recent advances in steady aerodynamic shape-design sensitivity analysis and optimization, based on advanced computational fluid dynamics. The focus here is on those methods particularly well- suited to the study of geometrically complex configurations and their potentially complex associated flow physics. When nonlinear state equations are considered in the optimization process, difficulties are found in the application of sensitivity analysis. Some techniques for circumventing such difficulties are currently being explored and are included here. Attention is directed to methods that utilize automatic differentiation to obtain aerodynamic sensitivity derivatives for both complex configurations and complex flow physics. Various examples of shape-design sensitivity analysis for unstructured-grid computational fluid dynamics algorithms are demonstrated for different formulations of the sensitivity equations. Finally, the use of advanced, unstructured-grid computational fluid dynamics in multidisciplinary analyses and multidisciplinary sensitivity analyses within future optimization processes is recommended and encouraged.

Fully unsteady subsonic and supersonic potential aerodynamics for complex aircraft configurations with applications to flutter

NASA Technical Reports Server (NTRS)

Tseng, K.; Morino, L.

1975-01-01

A general formulation is presented for the analysis of steady and unsteady, subsonic and supersonic aerodynamics for complex aircraft configurations. The theoretical formulation, the numerical procedure, the description of the program SOUSSA (steady, oscillatory and unsteady, subsonic and supersonic aerodynamics) and numerical results are included. In particular, generalized forces for fully unsteady (complex frequency) aerodynamics for a wing-body configuration, AGARD wing-tail interference in both subsonic and supersonic flows as well as flutter analysis results are included. The theoretical formulation is based upon an integral equation, which includes completely arbitrary motion. Steady and oscillatory aerodynamic flows are considered. Here small-amplitude, fully transient response in the time domain is considered. This yields the aerodynamic transfer function (Laplace transform of the fully unsteady operator) for frequency domain analysis. This is particularly convenient for the linear systems analysis of the whole aircraft.

Nuclear structure properties of the double-charge-exchange transition amplitudes

NASA Astrophysics Data System (ADS)

Auerbach, N.; Zheng, D. C.

1992-03-01

Nuclear structure aspects of the double-charge-exchange (DCX) reaction on nuclei are studied. Using a variety of DCX-type two-body transition operators, we explore the influence of two-body correlations among valence nucleons on the DCX transition amplitudes to the isobaric analog state and to other nonanalog J π=0+ states. In particular, the question of the spin dependence and of the range of the DCX transition operators is explored and the behavior of the transition amplitudes as a function of the valence nucleon number is studied. It is shown that the two-amplitude DCX formula derived by Auerbach, Gibbs, and Piasetzky for a single j n configuration holds also in some cases when configuration mixing is strong. DCX-type transitions from the Ca and Ni isotopes to the Ti and Zn isotopes and from 56Fe to 56Ni are the subject of this study.

Applying CBR to machine tool product configuration design oriented to customer requirements

NASA Astrophysics Data System (ADS)

Wang, Pengjia; Gong, Yadong; Xie, Hualong; Liu, Yongxian; Nee, Andrew Yehching

2017-01-01

Product customization is a trend in the current market-oriented manufacturing environment. However, deduction from customer requirements to design results and evaluation of design alternatives are still heavily reliant on the designer's experience and knowledge. To solve the problem of fuzziness and uncertainty of customer requirements in product configuration, an analysis method based on the grey rough model is presented. The customer requirements can be converted into technical characteristics effectively. In addition, an optimization decision model for product planning is established to help the enterprises select the key technical characteristics under the constraints of cost and time to serve the customer to maximal satisfaction. A new case retrieval approach that combines the self-organizing map and fuzzy similarity priority ratio method is proposed in case-based design. The self-organizing map can reduce the retrieval range and increase the retrieval efficiency, and the fuzzy similarity priority ratio method can evaluate the similarity of cases comprehensively. To ensure that the final case has the best overall performance, an evaluation method of similar cases based on grey correlation analysis is proposed to evaluate similar cases to select the most suitable case. Furthermore, a computer-aided system is developed using MATLAB GUI to assist the product configuration design. The actual example and result on an ETC series machine tool product show that the proposed method is effective, rapid and accurate in the process of product configuration. The proposed methodology provides a detailed instruction for the product configuration design oriented to customer requirements.

On the Morphology of a Growing City: A Heuristic Experiment Merging Static Economics with Dynamic Geography.

PubMed

Delloye, Justin; Peeters, Dominique; Thomas, Isabelle

2015-01-01

In this paper, we aim at exploring how individual location decisions affect the shape of a growing city and, more precisely, how they may add up to a configuration that diverges from equilibrium configurations formulated ex-ante. To do so, we provide a two-sector city model merging a static equilibrium analysis with agent-based simulations. Results show that under strong agglomeration effects, urban development is monotonic and ends up with circular, monocentric long-term configurations. For low agglomeration effects however, elongated and multicentric urban configurations may emerge. The occurrence and underlying dynamics of these configurations are also discussed regarding commuting costs and the distance-decay of agglomeration economies between firms. To sum up, our paper warns urban planning policy makers against the difference that may stand between appropriate long-term perspectives, represented here by analytic equilibrium configurations, and short-term urban configurations, simulated here by a multi-agent system.

J-2X Fuel Turbopump Point of Departure: The Performance of the J-2s Fuel Turbopump Inducer

NASA Technical Reports Server (NTRS)

Sargent, S. R.; Becht, D. G.; Mulder, A. D.

2008-01-01

To aid the J-2X program design effort with detailed performance and environment information, the J-2S fuel turbopump (FTP) inducer has undergone a thorough test series in both water and hydrogen. The test series utilizes both inducer only and a complete pump configuration to assess the inducer interaction to the overall turbopump system. The test goals include verification of suction performance against heritage J-2S data, head production, effects of thermodynamic suppression head (TSH), and evaluation of the inducer dynamic pressure caused by cavitation instabilities. Test facilities at both Pratt & Whitney Rocketdyne (PWR) and NASA s Stennis Space Center (SSC) are employed for the testing. The inducer only water test effort conducted at PWR established performance curves for suction performance, head production, and efficiency over a wide operating range. Because the heritage J-2S suction performance data set is in hydrogen, it is desired to obtain current suction performance data in hydrogen as well, thus avoiding the reliance on a theoretical TSH correlation for direct comparison. This data then provides an empirically based TSH correlation allowing for the comparison of water test suction data to system suction requirements. The FTP testing performed at SSC provides these suction performance relationships as well as inlet duct dynamic pressures during liquid hydrogen operation. The test effort successfully confirms the heritage J-2S suction performance and establishes the amount of TSH between water and hydrogen operation at the design flow coefficient. Correlating data is also obtained for cavitating instability frequency content, illustrating the validity of using the wide flow range water test data to predict hydrogen performance.

Atomic alignment effect on reactivity and on product alignment in the energy-transfer reaction of oriented Ar (3P2, 4s [3/2]2, M(J) = 2) + Kr (4p6, 1S0) → Ar (3p6, 1S0) + Kr (5p [3/2]2).

PubMed

Ohoyama, H

2015-03-12

Steric effect for the formation of Kr (5p [3/2]₂) in the energy transfer reaction of Ar (³P₂, 4s [3/2]₂) + Kr has been studied by using an oriented Ar (³P₂, 4s [3/2]₂, M(J) = 2) beam at a collision energy of ∼0.09 eV. The emission intensity of Kr (5p [3/2]₂) is ca. 2 times enhanced when the angular momentum (J(Ar)) of Ar (³P₂) is aligned perpendicular to the relative velocity vector (v(R)). In addition, the Kr (5p [3/2]₂) emission is highly polarized parallel to v(R) (I(∥)/I(⊥) ∼ 1.2) when JAr is aligned perpendicular to v(R). The observed polarization moments indicate that the alignment of the unpaired Ar (3p) orbital of Ar (³P₂) to v(R), (Σ (|L′| = 0), Π (|L′| = 1)), dominates the energy transfer probability (σ(Π)(∥): σ(Σ)(∥): σ(Π)(⊥): σ(Σ)(⊥) = 0.49:1.33:0.55:1.23) and also the alignment of the Kr (5p) orbital of Kr (5p [3/2]₂) to v(R): the Σ-configuration of the Ar (3p) orbital leads to the parallel alignment (Σ-configuration) of the Kr(5p) orbital to v(R), conversely, the Π-configuration of Ar (3p) orbital leads to the perpendicular alignment (Π-configuration) of the Kr(5p) orbital. In addition, the selectivity of the alignment of the Kr (5p) orbital turns out to vary from perpendicular to parallel as the collision energy increases after a threshold down to 0.03 eV.

Gravitational collapse and rotation. II - Gravitational radiation and reduction of the a/m ratio

NASA Astrophysics Data System (ADS)

de Felice, F.; Miller, J. C.; Yu, Y.

1985-11-01

During collapse of a nonaxisymmetric rotating ellipsoid, gravitational radiation causes a loss of mass M and angular momentum J. Their combined effect on the behavior of the ratio a/m = cJ/GM2 is investigated for constant density models within a post-Newtonian scheme, and it is found that whenever the value of the ratio is initially greater than 1, it tends toward 1 as the configuration approaches the black hole limit.

The Javalambre Survey Telescope (JST/T250): a multi-filter surveying machine for the Northern hemisphere

NASA Astrophysics Data System (ADS)

Cenarro, Javier; Marin-Franch, Antonio; Moles, Mariano; Cristobal-Hornillos, David; Dupke, Renato a.; Benitez, Txitxo; Taylor, Keith

2015-08-01

The Javalambre Survey Telescope (JST/T250) is a 2.55m Richey-Chretien, alt-azimuthal telescope with a field of view of diameter 3 deg and an effective etendue of 26.5 m2deg2 operated by the Centro de Estudios de Física del Cosmos de Aragón (CEFCA) at the Observatorio Astrofísico de Javalambre (OAJ). JST/T250 is particularly conceived and defined for carrying out large sky multi-filter surveys, like J-PAS (http://j-pas.org), which will be the main survey to be conducted during the first years of operation. To guarantee a seeing limited image quality all over the ~0.5m diameter focal plane, JST/T250 hosts state-of-the-arte optics, including complex hyperbolic M1 and M2 mirrors and a challenging field corrector of three lenses with 4 aspherical surfaces and high slopes. The optical configuration ends up with the powered entrance window of JPCam, the panoramic camera for J-PAS, with ~1200Mpix in a mosaic of 14 large format CCDs of 9.2k x 9.2k, and a set of 56 narrow-band, contiguous, optical filters. In this poster we present a detailed view of the telescope configuration, its optical performance and the expected operation for the J-PAS survey execution.

Analyses of Injection-Coupled Combustion Instability from J-2X Gas Generator Development

NASA Technical Reports Server (NTRS)

Hulka, James R.; Kenny, R. Jeremy; Protz, Chris; Casiano, Matthew

2011-01-01

During development of the gas generator for the liquid oxygen/liquid hydrogen propellant J-2X rocket engine, combustion instabilities were observed near the frequency of the first longitudinal acoustic mode of the hot gas combustion chamber duct. These instabilities were similar to intermediate-frequency or buzz-type instabilities as described in historical programs, except for several aspects: 1) the frequencies were low, in the realm of chug; 2) at times the instability oscillation amplitudes were quite large, with peak-to-peak amplitudes exceeding 50% of the mean chamber pressure along with the appearance of harmonics; 3) the chamber excitation was related to but not exactly at the first longitudinal combustion chamber acoustic mode; and 4) the injector provided mass flow rate oscillations induced by capacitance and inertance effects in the injector rather than by organ pipe resonances of the coaxial oxidizer posts. This type of combustion instability is referred to as "injection coupling" because one critical driving source of the instability is mass flow rate oscillations from the injector. However, the type of injection coupling observed here is different than observed in previous instances of buzz instability with coaxial injectors, because of the lower frequencies and lack of influence from the oxidizer post organ pipe resonances. Test data and preliminary analyses of the initial combustion instabilities were presented in several papers at the 5th Liquid Propulsion Subcommittee meeting. Since that time, additional hot-fire tests with several new hardware configurations have been conducted, and additional analyses have been completed. The analytical models described in previous papers have been updated to include the influences of new geometrical configurations, including a different oxidizer injector manifold configuration and a branch pipe in the hot gas duct that supplies gaseous helium during the start transient to pre-spin the turbine. In addition, the analysis methodology has been revisited to evaluate the potential influence of a combustion response as well as an injection response.

Electrostatics of proteins in dielectric solvent continua. I. Newton's third law marries qE forces

NASA Astrophysics Data System (ADS)

Stork, Martina; Tavan, Paul

2007-04-01

The authors reformulate and revise an electrostatic theory treating proteins surrounded by dielectric solvent continua [B. Egwolf and P. Tavan, J. Chem. Phys. 118, 2039 (2003)] to make the resulting reaction field (RF) forces compatible with Newton's third law. Such a compatibility is required for their use in molecular dynamics (MD) simulations, in which the proteins are modeled by all-atom molecular mechanics force fields. According to the original theory the RF forces, which are due to the electric field generated by the solvent polarization and act on the partial charges of a protein, i.e., the so-called qE forces, can be quite accurately computed from Gaussian RF dipoles localized at the protein atoms. Using a slightly different approximation scheme also the RF energies of given protein configurations are obtained. However, because the qE forces do not account for the dielectric boundary pressure exerted by the solvent continuum on the protein, they do not obey the principle that actio equals reactio as required by Newton's third law. Therefore, their use in MD simulations is severely hampered. An analysis of the original theory has led the authors now to a reformulation removing the main difficulties. By considering the RF energy, which represents the dominant electrostatic contribution to the free energy of solvation for a given protein configuration, they show that its negative configurational gradient yields mean RF forces obeying the reactio principle. Because the evaluation of these mean forces is computationally much more demanding than that of the qE forces, they derive a suggestion how the qE forces can be modified to obey Newton's third law. Various properties of the thus established theory, particularly issues of accuracy and of computational efficiency, are discussed. A sample application to a MD simulation of a peptide in solution is described in the following paper [M. Stork and P. Tavan, J. Chem. Phys., 126, 165106 (2007).

Low-temperature heat capacity of diopside glass (CaMgSi2O6): A calorimetric test of the configurational-entropy theory applied to the viscosity of liquid silicates

USGS Publications Warehouse

Richet, P.; Robie, R.A.; Hemingway, B.S.

1986-01-01

Heat-capacity measurements have been made between 8 and 370 K on an annealed and a rapidly quenched diopside glass. Between 15 and 200 K, Cp does not depend significantly on the thermal history of the glass. Below 15 K Cp is larger for the quenched than for the annealed specimen. The opposite is true above 200 K as a result of what is interpreted as a secondary relaxation around room temperature. The magnitude of these effects, however, is small enough that the relative entropies S(298)-S(0) of the glasses differ by only 0.5 J/mol K, i.e., a figure within the combined experimental uncertainties. The insensitivity of relative entropies to thermal history supports the assumption that the configurational heat capacity of the liquid may be taken as the heat capacity difference between the liquid and the glass (??Cp). Furthermore, this insensitivity allows calculation of the residual entropies at 0 K of diopside glasses as a function of the fictive temperature from the entropy of fusion of diopside and the heat capacities of the crystalline, glassy and liquid phases. For a glass with a fictive temperature of 1005 K, for example, this calorimetric residual entropy is 24.3 ?? 3 J/mol K, in agreement with the prediction made by RICHET (1984) from an analysis of the viscosity data with the configurational-entropy theory of relaxation processes of Adam and Gibbs (1965). In turn, all the viscosity measurements for liquid diopside, which span the range 0.5-4?? 1013 poise, can be quantitatively reproduced through this theory with the calorimetrically determined entropies and ??Cp data. Finally, the unclear significance of "activation energies" for structural interpretations of viscosity data is emphasized, and the importance of ??Cp and glass-transition temperature systematics for determining the composition and temperature dependences of the viscosity is pointed out. ?? 1986.

Stochastic quasi-Newton molecular simulations

NASA Astrophysics Data System (ADS)

Chau, C. D.; Sevink, G. J. A.; Fraaije, J. G. E. M.

2010-08-01

We report a new and efficient factorized algorithm for the determination of the adaptive compound mobility matrix B in a stochastic quasi-Newton method (S-QN) that does not require additional potential evaluations. For one-dimensional and two-dimensional test systems, we previously showed that S-QN gives rise to efficient configurational space sampling with good thermodynamic consistency [C. D. Chau, G. J. A. Sevink, and J. G. E. M. Fraaije, J. Chem. Phys. 128, 244110 (2008)10.1063/1.2943313]. Potential applications of S-QN are quite ambitious, and include structure optimization, analysis of correlations and automated extraction of cooperative modes. However, the potential can only be fully exploited if the computational and memory requirements of the original algorithm are significantly reduced. In this paper, we consider a factorized mobility matrix B=JJT and focus on the nontrivial fundamentals of an efficient algorithm for updating the noise multiplier J . The new algorithm requires O(n2) multiplications per time step instead of the O(n3) multiplications in the original scheme due to Choleski decomposition. In a recursive form, the update scheme circumvents matrix storage and enables limited-memory implementation, in the spirit of the well-known limited-memory Broyden-Fletcher-Goldfarb-Shanno (L-BFGS) method, allowing for a further reduction of the computational effort to O(n) . We analyze in detail the performance of the factorized (FSU) and limited-memory (L-FSU) algorithms in terms of convergence and (multiscale) sampling, for an elementary but relevant system that involves multiple time and length scales. Finally, we use this analysis to formulate conditions for the simulation of the complex high-dimensional potential energy landscapes of interest.

A computer program for two-particle generalized coefficients of fractional parentage

NASA Astrophysics Data System (ADS)

Deveikis, A.; Juodagalvis, A.

2008-10-01

We present a FORTRAN90 program GCFP for the calculation of the generalized coefficients of fractional parentage (generalized CFPs or GCFP). The approach is based on the observation that the multi-shell CFPs can be expressed in terms of single-shell CFPs, while the latter can be readily calculated employing a simple enumeration scheme of antisymmetric A-particle states and an efficient method of construction of the idempotent matrix eigenvectors. The program provides fast calculation of GCFPs for a given particle number and produces results possessing numerical uncertainties below the desired tolerance. A single j-shell is defined by four quantum numbers, (e,l,j,t). A supplemental C++ program parGCFP allows calculation to be done in batches and/or in parallel. Program summaryProgram title:GCFP, parGCFP Catalogue identifier: AEBI_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEBI_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 17 199 No. of bytes in distributed program, including test data, etc.: 88 658 Distribution format: tar.gz Programming language: FORTRAN 77/90 ( GCFP), C++ ( parGCFP) Computer: Any computer with suitable compilers. The program GCFP requires a FORTRAN 77/90 compiler. The auxiliary program parGCFP requires GNU-C++ compatible compiler, while its parallel version additionally requires MPI-1 standard libraries Operating system: Linux (Ubuntu, Scientific) (all programs), also checked on Windows XP ( GCFP, serial version of parGCFP) RAM: The memory demand depends on the computation and output mode. If this mode is not 4, the program GCFP demands the following amounts of memory on a computer with Linux operating system. It requires around 2 MB of RAM for the A=12 system at E⩽2. Computation of the A=50 particle system requires around 60 MB of RAM at E=0 and ˜70 MB at E=2 (note, however, that the calculation of this system will take a very long time). If the computation and output mode is set to 4, the memory demands by GCFP are significantly larger. Calculation of GCFPs of A=12 system at E=1 requires 145 MB. The program parGCFP requires additional 2.5 and 4.5 MB of memory for the serial and parallel version, respectively. Classification: 17.18 Nature of problem: The program GCFP generates a list of two-particle coefficients of fractional parentage for several j-shells with isospin. Solution method: The method is based on the observation that multishell coefficients of fractional parentage can be expressed in terms of single-shell CFPs [1]. The latter are calculated using the algorithm [2,3] for a spectral decomposition of an antisymmetrization operator matrix Y. The coefficients of fractional parentage are those eigenvectors of the antisymmetrization operator matrix Y that correspond to unit eigenvalues. A computer code for these coefficients is available [4]. The program GCFP offers computation of two-particle multishell coefficients of fractional parentage. The program parGCFP allows a batch calculation using one input file. Sets of GCFPs are independent and can be calculated in parallel. Restrictions:A<86 when E=0 (due to the memory constraints); small numbers of particles allow significantly higher excitations, though the shell with j⩾11/2 cannot get full (it is the implementation constraint). Unusual features: Using the program GCFP it is possible to determine allowed particle configurations without the GCFP computation. The GCFPs can be calculated either for all particle configurations at once or for a specified particle configuration. The values of GCFPs can be printed out with a complete specification in either one file or with the parent and daughter configurations printed in separate files. The latter output mode requires additional time and RAM memory. It is possible to restrict the ( J,T) values of the considered particle configurations. (Here J is the total angular momentum and T is the total isospin of the system.) The program parGCFP produces several result files the number of which equals to the number of particle configurations. To work correctly, the program GCFP needs to be compiled to read parameters from the standard input (the default setting). Running time: It depends on the size of the problem. The minimum time is required, if the computation and output mode ( CompMode) is not 4, but the resulting file is larger. A system with A=12 particles at E=0 (all 9411 GCFPs) took around 1 sec on a Pentium4 2.8 GHz processor with 1 MB L2 cache. The program required about 14 min to calculate all 1.3×10 GCFPs of E=1. The time for all 5.5×10 GCFPs of E=2 was about 53 hours. For this number of particles, the calculation time of both E=0 and E=1 with CompMode = 1 and 4 is nearly the same, when no other processes are running. The case of E=2 could not be calculated with CompMode = 4, because the RAM memory was insufficient. In general, the latter CompMode requires a longer computation time, although the resulting files are smaller in size. The program parGCFP puts virtually no time overhead. Its parallel version speeds-up the calculation. However, the results need to be collected from several files created for each configuration. References: [1] J. Levinsonas, Works of Lithuanian SSR Academy of Sciences 4 (1957) 17. [2] A. Deveikis, A. Bončkus, R. Kalinauskas, Lithuanian Phys. J. 41 (2001) 3. [3] A. Deveikis, R.K. Kalinauskas, B.R. Barrett, Ann. Phys. 296 (2002) 287. [4] A. Deveikis, Comput. Phys. Comm. 173 (2005) 186. (CPC Catalogue ID. ADWI_v1_0)

Exploring the novel donor-nanotube archetype as an efficient third-order nonlinear optical material: asymmetric open-shell carbon nanotubes.

PubMed

Muhammad, Shabbir; Nakano, Masayoshi; Al-Sehemi, Abdullah G; Irfan, Ahmad; Chaudhry, Aijaz Rasool; Tonami, Takayoshi; Ito, Soichi; Kishi, Ryohei; Kitagawa, Yasutaka

2018-06-06

Contrary to the enormous number of previous studies on carbon nanotubes (CNTs), herein, we realized the origin of the intrinsic open-shell diradical character and second hyperpolarizability γ using a broken symmetry approach. This study was inspired by our recent findings (S. Muhammad, et al., Nanoscale, 2016, 8, 17998 and Nakano, et al., J. Phys. Chem. C, 2016, 120, 1193). We performed structural modifications through a unique asymmetric donor-nanotube framework, which led to a novel paradigm of modified CNTs with tunable open-shell diradical character and remarkably superior NLO response properties. Interestingly, asymmetry and diradical character were found to be the crucial factors to modulate the second hyperpolarizability γ. We initially performed a comparative analysis of the diradical characters and γ amplitudes of boron nitride nanotubes (BNNTs) and CNTs possessing significant ionic characters and covalent characters, respectively. The basic findings for these simple configurations were further extended to the donor-acceptor CNT paradigm, which finally led to excellent asymmetric donor-CNT configurations with remarkably larger γ amplitudes. Furthermore, among the CNTs, finite length zigzag CNT(6,0)3 were modified with different donor-acceptor configurations. Interestingly, for the first time, unique donor-nanotube configurations [1,4-(NH2)2CNT-(6,0)3 and 1,4-(NH2)2CNT-(6,0)5] were found; they showed significantly robust γ amplitudes as large as 2519 × 103 and 4090 × 103 a.u. at the LC-UBLYP(μ = 0.33)/6-31G* level of theory. Additionally, several molecular level insights have been obtained for these novel donor-nanotube configurations using their odd electron densities, molecular electrostatic maps, densities of states and γ density analyses to highlight the realization of these novel materials for highly efficient optical and NLO applications.

Metabolite Differentiation and Discovery Lab (MeDDL): A New Tool for Biomarker Discovery and Mass Spectral Visualization

DTIC Science & Technology

2010-06-01

Jeremy Nicholson, Elaine Holmes , and John Lindon at the Imperial College in London1 utilizing nuclear magnetic resonance (NMR) based analysis, has...Lindon, J. C.; Holmes , E. Xenobiotica 1999, 29, 1181– 1189. (2) Pham-Tuan, H.; Kaskavelis, L.; Daykin, C.; Janssen, H. J. Chromatogr. B 2003, 789, 283...301. (3) Lindon, J.; Holmes , E.; Nicholson, J. Pharm. Res. 2006, 23, 1075–1088. (4) Robertson, D. Toxicol. Sci. 2005, 85, 809–822. (5) Nicholson, J

Determination of the absolute configuration of two estrogenic nonylphenols in solution by chiroptical methods

NASA Astrophysics Data System (ADS)

Reinscheid, Uwe M.

2009-01-01

The absolute configurations of two estrogenic nonylphenols were determined in solution. Both nonylphenols, NP35 and NP112 could not be crystallized so that only solution methods are able to solve directly the question of absolute configuration. The conclusion based on experimental and calculated optical rotation and VCD data for the nonylphenol NP35 was independently confirmed by another study using a camphanoyl derivative and X-ray analysis of the obtained crystals. In case of NP112, the experimental rotation data are inconclusive. However, the comparison between experimental and calculated VCD data allowed the determination of the absolute configuration.

Analysis of the symmetric configuration of the circle of Willis in a series of autopsied corpses.

PubMed

Stojanović, Nebojga; Stefanović, Ivica; Kostić, Aleksandar; Radisavejević, Misa; Stojanov, Dragan; Petrović, Sladjana

2015-04-01

The forming of the blood vessels network configuration at the base of the brain and interconnecting of blood vessels during the embryogenesis is directly related to the phylogenetic development of the brain and brain structures. A blood vessel configuration at the brain base, in the form of a ring or a hexagon, stands in direct relation to the perfusion needs of certain parts of the brain during its primary differentiation. The aim of this paper was to determine the incidence of certain blood vessel configurations at the base of the brain and understanding their symmetry or asymmetry. Analysis of the blood vessels at the base of the brain was performed on the autopsied subjects. The object of observation was the anterior segment of the circle of Willis consisting of C1- a. carotis interna (ICA), above a. communicaus posterior (PcoA), the segment A1 a. cerebri anterior (ACA) from a. carotis interna bifurcation to the a. communicans anterior (AcoA) and a communicans anterior itself, as well as the posterior segment consisting of PcoA and the segment P1--a. cerebri posterior (PCA) from the a. basilaris bifurcation to the PcoA. For the purpose of grouping the findings, the four basic configuration types of the circle of Willis were identified based on its symmetry or asymmetry. Type-A (symmetric circle of Willis), type-B (asymmetric circle of Willis' due to the unilateral hypoplastic A1-ACA); type-C (symmetric circle of Willis with bilateral symmetric changes on PcoA) and type-D (asymmetric circle of Willis due to the asymmetric changes on PcoA). Autosy was performed on 56 corpses. A total of 41 (73.2%) subjects were recorded with a symmetric configuration of the circle of Willis', of which 27 (48.2%) subjects had type A and 14 (25%) type C. The asymmetric configuration was present in 15 (26.8%) subjects, of whom 9 (16%) had type B and 6 (10.8%) subjects, of whom 9 (16%) had type B and 6 (10.8%) type D. The symmetric Willis group (73.2%) did not have a homogeneous finding that would fit into the schematic presentation of the symmetric type A and type C. A total of 17 (30.4%) findings were classified in this group of the so-called conditionally symmetric configurations. In all the cases, type B (16%) had unilaterally reduced diameter A1 and hyperplastic AcoA. The presence of asymmetric Willis configuration in 26.8% of the cases, which makes up more than one fourth, indicates that the asymmetric configurations do not represent a pathological form of connecting the blood vessels at the base of the brain, but rather one aspect of its adaptation. The forming of the basic types of configurations of the circle of Willis is associated with a tendency toward certain types of hemodynamic disorders and more frequent pathological changes in places of reduced resistance.

Critical assessment of Pt surface energy - An atomistic study

NASA Astrophysics Data System (ADS)

Kim, Jin-Soo; Seol, Donghyuk; Lee, Byeong-Joo

2018-04-01

Despite the fact that surface energy is a fundamental quantity in understanding surface structure of nanoparticle, the results of experimental measurements and theoretical calculations for the surface energy of pure Pt show a wide range of scattering. It is necessary to further ensure the surface energy of Pt to find the equilibrium shape and atomic configuration in Pt bimetallic nanoparticles accurately. In this article, we critically assess and optimize the Pt surface energy using a semi-empirical atomistic approach based on the second nearest-neighbor modified embedded-atom method interatomic potential. That is, the interatomic potential of pure Pt was adjusted in a way that the surface segregation tendency in a wide range of Pt binary alloys is reproduced in accordance with experimental information. The final optimized Pt surface energy (mJ/m2) is 2036 for (100) surface, 2106 for (110) surface, and 1502 for (111) surface. The potential can be utilized to find the equilibrium shape and atomic configuration of Pt bimetallic nanoparticles more accurately.

Pulsed high-peak-power and single-frequency fibre laser design for LIDAR aircraft safety application

NASA Astrophysics Data System (ADS)

Liégeois, Flavien; Vercambre, Clément; Hernandez, Yves; Salhi, Mohamed; Giannone, Domenico

2006-09-01

Laser wind velocimeters work by monitoring the Doppler shift induced on the backscattered light by aerosols that are present in the air. Recently there has been a growing interest in the scientific community for developing systems operating at wavelengths near 1.5 μm and based on all-fibre lasers configuration. In this paper, we propose a new all-fibre laser source that is suitable for Doppler velocimetry in aircraft safety applications. The all-fibre laser has been specifically conceived for aircraft safety application. Our prototype has a conveniently narrow linewidth (9 kHz) and is modulated and amplified through an all fibre Master Oscillator Power Amplifier (MOPA) configuration. According to the measurements, we performed the final characteristics of the laser consist in a maximum peak power of 2.7 kW and an energy of 27 μJ energy per pulses of 10 ns at 30 kHz repetition rate. The only limiting factor of these performances is the Stimulated Brillouin Scattering.

Marker Configuration Model-Based Roentgen Fluoroscopic Analysis.

PubMed

Garling, Eric H; Kaptein, Bart L; Geleijns, Koos; Nelissen, Rob G H H; Valstar, Edward R

2005-04-01

It remains unknown if and how the polyethylene bearing in mobile bearing knees moves during dynamic activities with respect to the tibial base plate. Marker Configuration Model-Based Roentgen Fluoroscopic Analysis (MCM-based RFA) uses a marker configuration model of inserted tantalum markers in order to accurately estimate the pose of an implant or bone using single plane Roentgen images or fluoroscopic images. The goal of this study is to assess the accuracy of (MCM-Based RFA) in a standard fluoroscopic set-up using phantom experiments and to determine the error propagation with computer simulations. The experimental set-up of the phantom study was calibrated using a calibration box equipped with 600 tantalum markers, which corrected for image distortion and determined the focus position. In the computer simulation study the influence of image distortion, MC-model accuracy, focus position, the relative distance between MC-models and MC-model configuration on the accuracy of MCM-Based RFA were assessed. The phantom study established that the in-plane accuracy of MCM-Based RFA is 0.1 mm and the out-of-plane accuracy is 0.9 mm. The rotational accuracy is 0.1 degrees. A ninth-order polynomial model was used to correct for image distortion. Marker-Based RFA was estimated to have, in a worst case scenario, an in vivo translational accuracy of 0.14 mm (x-axis), 0.17 mm (y-axis), 1.9 mm (z-axis), respectively, and a rotational accuracy of 0.3 degrees. When using fluoroscopy to study kinematics, image distortion and the accuracy of models are important factors, which influence the accuracy of the measurements. MCM-Based RFA has the potential to be an accurate, clinically useful tool for studying kinematics after total joint replacement using standard equipment.

11.72-sq cm Active-Area Wafer Interconnected PiN Diode Pulsed at 64 kA Dissipates 382 J and Exhibits an Action of 1.7 MA(sup 2)-s

DTIC Science & Technology

2012-01-30

calculated action exceeded 1.7 MA2 -s. Preliminary efforts on high voltage diode interconnection have produced quarter wafer interconnected PiN...was packaged in a “hockey-puck” configuration and pulsed to 64 kA, dissipating 382 J with a calculated action exceeding 1.7 MA2 -s. II. FULL...epitaxial layers are utilized. 11.72-cm2 Active-area Wafer Interconnected PiN Diode pulsed at 64 kA dissipates 382 J and exhibits an action of 1.7 MA2 -s

Comment on 'Effects of magnetic field gradient on ion beam current in cylindrical Hall ion source' [J. Appl. Phys. 102, 123305 (2007)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raitses, Y.; Smirnov, A.; Fisch, N. J.

It is argued that the key difference in the cylindrical Hall thruster (CHT) as compared to the end-Hall ion source cannot be exclusively attributed to the magnetic field topology [Tang et al., J. Appl. Phys. 102, 123305 (2007)]. With a similar mirror-type topology, the CHT configuration provides the electric field with nearly equipotential magnetic field surfaces and a better suppression of the electron cross-field transport, as compared to both the end-Hall ion source and the cylindrical Hall ion source of [Tang et al., J. Appl. Phys. 102, 123305 (2007)].

Exploring the free energy surface using ab initio molecular dynamics

NASA Astrophysics Data System (ADS)

Samanta, Amit; Morales, Miguel A.; Schwegler, Eric

2016-04-01

Efficient exploration of configuration space and identification of metastable structures in condensed phase systems are challenging from both computational and algorithmic perspectives. In this regard, schemes that utilize a set of pre-defined order parameters to sample the relevant parts of the configuration space [L. Maragliano and E. Vanden-Eijnden, Chem. Phys. Lett. 426, 168 (2006); J. B. Abrams and M. E. Tuckerman, J. Phys. Chem. B 112, 15742 (2008)] have proved useful. Here, we demonstrate how these order-parameter aided temperature accelerated sampling schemes can be used within the Born-Oppenheimer and the Car-Parrinello frameworks of ab initio molecular dynamics to efficiently and systematically explore free energy surfaces, and search for metastable states and reaction pathways. We have used these methods to identify the metastable structures and reaction pathways in SiO2 and Ti. In addition, we have used the string method [W. E, W. Ren, and E. Vanden-Eijnden, Phys. Rev. B 66, 052301 (2002); L. Maragliano et al., J. Chem. Phys. 125, 024106 (2006)] within the density functional theory to study the melting pathways in the high pressure cotunnite phase of SiO2 and the hexagonal closed packed to face centered cubic phase transition in Ti.

Models of the strongly lensed quasar DES J0408−5354

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agnello, A.; et al.

We present gravitational lens models of the multiply imaged quasar DES J0408-5354, recently discovered in the Dark Energy Survey (DES) footprint, with the aim of interpreting its remarkable quad-like configuration. We first model the DES single-epochmore » $grizY$ images as a superposition of a lens galaxy and four point-like objects, obtaining spectral energy distributions (SEDs) and relative positions for the objects. Three of the point sources (A,B,D) have SEDs compatible with the discovery quasar spectra, while the faintest point-like image (G2/C) shows significant reddening and a `grey' dimming of $$\\approx0.8$$mag. In order to understand the lens configuration, we fit different models to the relative positions of A,B,D. Models with just a single deflector predict a fourth image at the location of G2/C but considerably brighter and bluer. The addition of a small satellite galaxy ($$R_{\\rm E}\\approx0.2$$") in the lens plane near the position of G2/C suppresses the flux of the fourth image and can explain both the reddening and grey dimming. All models predict a main deflector with Einstein radius between $1.7"$ and $2.0",$ velocity dispersion $267-280$km/s and enclosed mass $$\\approx 6\\times10^{11}M_{\\odot},$$ even though higher resolution imaging data are needed to break residual degeneracies in model parameters. The longest time-delay (B-A) is estimated as $$\\approx 85$$ (resp. $$\\approx125$$) days by models with (resp. without) a perturber near G2/C. The configuration and predicted time-delays of J0408-5354 make it an excellent target for follow-up aimed at understanding the source quasar host galaxy and substructure in the lens, and measuring cosmological parameters. We also discuss some lessons learnt from J0408-5354 on lensed quasar finding strategies, due to its chromaticity and morphology.« less

Computational Aerodynamic Analysis of Offshore Upwind and Downwind Turbines

DOE PAGES

Zhao, Qiuying; Sheng, Chunhua; Afjeh, Abdollah

2014-01-01

Aerodynamic interactions of the model NREL 5 MW offshore horizontal axis wind turbines (HAWT) are investigated using a high-fidelity computational fluid dynamics (CFD) analysis. Four wind turbine configurations are considered; three-bladed upwind and downwind and two-bladed upwind and downwind configurations, which operate at two different rotor speeds of 12.1 and 16 RPM. In the present study, both steady and unsteady aerodynamic loads, such as the rotor torque, blade hub bending moment, and base the tower bending moment of the tower, are evaluated in detail to provide overall assessment of different wind turbine configurations. Aerodynamic interactions between the rotor and tower are analyzed,more » including the rotor wake development downstream. The computational analysis provides insight into aerodynamic performance of the upwind and downwind, two- and three-bladed horizontal axis wind turbines.« less

Performance of J-33-A-21 and J-33-A-23 Compressors with and without Water Injection

NASA Technical Reports Server (NTRS)

Beede, William L.

1948-01-01

In an investigation of the J-33-A-21 and the J-33-A-23 compressors with and without water injection, it was discovered that the compressors reacted differently to water injection although they were physically similar. An analysis of the effect of water injection on compressor performance and the consequent effect on matching of the compressor and turbine components in the turbojet engine was made. The analysis of component matching is based on a turbine flow function defined as the product of the equivalent weight flow and the reciprocal of the compressor pressure ratio.

14 CFR Appendix J to Part 141 - Aircraft Type Rating Course, For Other Than an Airline Transport Pilot Certificate

Code of Federal Regulations, 2013 CFR

2013-01-01

... control of airspeed, configuration, direction, altitude, and attitude in accordance with procedures and... preflight; and (7) Use of the aircraft's prestart checklist, appropriate control system checks, starting...

14 CFR Appendix J to Part 141 - Aircraft Type Rating Course, For Other Than an Airline Transport Pilot Certificate

Code of Federal Regulations, 2014 CFR

2014-01-01

... control of airspeed, configuration, direction, altitude, and attitude in accordance with procedures and... preflight; and (7) Use of the aircraft's prestart checklist, appropriate control system checks, starting...

14 CFR Appendix J to Part 141 - Aircraft Type Rating Course, For Other Than an Airline Transport Pilot Certificate

Code of Federal Regulations, 2012 CFR

2012-01-01

... control of airspeed, configuration, direction, altitude, and attitude in accordance with procedures and... preflight; and (7) Use of the aircraft's prestart checklist, appropriate control system checks, starting...

14 CFR Appendix J to Part 141 - Aircraft Type Rating Course, For Other Than an Airline Transport Pilot Certificate

Code of Federal Regulations, 2011 CFR

2011-01-01

... control of airspeed, configuration, direction, altitude, and attitude in accordance with procedures and... preflight; and (7) Use of the aircraft's prestart checklist, appropriate control system checks, starting...

23 CFR 940.11 - Project implementation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... projects funded with highway trust funds shall be based on a systems engineering analysis. (b) The analysis should be on a scale commensurate with the project scope. (c) The systems engineering analysis shall... definitions; (4) Analysis of alternative system configurations and technology options to meet requirements; (5...

23 CFR 940.11 - Project implementation.

Code of Federal Regulations, 2014 CFR

2014-04-01

... projects funded with highway trust funds shall be based on a systems engineering analysis. (b) The analysis should be on a scale commensurate with the project scope. (c) The systems engineering analysis shall... definitions; (4) Analysis of alternative system configurations and technology options to meet requirements; (5...

23 CFR 940.11 - Project implementation.

Code of Federal Regulations, 2012 CFR

2012-04-01

... projects funded with highway trust funds shall be based on a systems engineering analysis. (b) The analysis should be on a scale commensurate with the project scope. (c) The systems engineering analysis shall... definitions; (4) Analysis of alternative system configurations and technology options to meet requirements; (5...

23 CFR 940.11 - Project implementation.

Code of Federal Regulations, 2013 CFR

2013-04-01

... projects funded with highway trust funds shall be based on a systems engineering analysis. (b) The analysis should be on a scale commensurate with the project scope. (c) The systems engineering analysis shall... definitions; (4) Analysis of alternative system configurations and technology options to meet requirements; (5...

23 CFR 940.11 - Project implementation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... projects funded with highway trust funds shall be based on a systems engineering analysis. (b) The analysis should be on a scale commensurate with the project scope. (c) The systems engineering analysis shall... definitions; (4) Analysis of alternative system configurations and technology options to meet requirements; (5...

The Aeronautical Data Link: Taxonomy, Architectural Analysis, and Optimization

NASA Technical Reports Server (NTRS)

Morris, A. Terry; Goode, Plesent W.

2002-01-01

The future Communication, Navigation, and Surveillance/Air Traffic Management (CNS/ATM) System will rely on global satellite navigation, and ground-based and satellite based communications via Multi-Protocol Networks (e.g. combined Aeronautical Telecommunications Network (ATN)/Internet Protocol (IP)) to bring about needed improvements in efficiency and safety of operations to meet increasing levels of air traffic. This paper will discuss the development of an approach that completely describes optimal data link architecture configuration and behavior to meet the multiple conflicting objectives of concurrent and different operations functions. The practical application of the approach enables the design and assessment of configurations relative to airspace operations phases. The approach includes a formal taxonomic classification, an architectural analysis methodology, and optimization techniques. The formal taxonomic classification provides a multidimensional correlation of data link performance with data link service, information protocol, spectrum, and technology mode; and to flight operations phase and environment. The architectural analysis methodology assesses the impact of a specific architecture configuration and behavior on the local ATM system performance. Deterministic and stochastic optimization techniques maximize architectural design effectiveness while addressing operational, technology, and policy constraints.

Collisional PIC Simulations of Particles in Magnetic Fields

NASA Astrophysics Data System (ADS)

Peter, William

2003-10-01

Because of the long range of Coloumb forces, collisions with distant particles in plasmas are more important than collisions with near neighbors. In addition, many problems in space physics and magnetic confinement include regions of weak magnetic field where the MHD approximation breaks down. A particle-in-cell code based on the quiet direct simulation Monte-Carlo method(B. J. Albright, W. Daughton, D. Lemons, D. Winske, and M. E. Jones, Physics of Plasmas) 9, 1898 (2002). is being developed to study collisional (e.g., ν ˜ Ω) particle motion in magnetic fields. Primary application is to energetic particle loss in the radiation belts(K. Papadopoulos, COSPAR Meeting, Houston, TX, Oct., 2002.) at a given energy and L-shell. Other applications include trapping in rotating field-reversed configurations(N. Rostoker and A. Qerushi, Physics of Plasmas) 9, 3057 (2002)., and electron behavior in magnetic traps(V. Gorgadze, T. Pasquini, J. S. Wurtele, and J. Fajans, Bull. Am. Phys. Soc.) 47, 127 (2002).. The use of the random time-step method(W. Peter, Bull. Am. Phys. Soc.) 47, 52 (2002). to decrease simulation times by 1-2 orders of magnitude is also being studied.

The across frequency independence of equalization of interaural time delay in the equalization-cancellation model of binaural unmasking.

PubMed

Akeroyd, Michael A

2004-08-01

The equalization stage in the equalization-cancellation model of binaural unmasking compensates for the interaural time delay (ITD) of a masking noise by introducing an opposite, internal delay [N. I. Durlach, in Foundations of Modern Auditory Theory, Vol. II., edited by J. V. Tobias (Academic, New York, 1972)]. Culling and Summerfield [J. Acoust. Soc. Am. 98, 785-797 (1995)] developed a multi-channel version of this model in which equalization was "free" to use the optimal delay in each channel. Two experiments were conducted to test if equalization was indeed free or if it was "restricted" to the same delay in all channels. One experiment measured binaural detection thresholds, using an adaptive procedure, for 1-, 5-, or 17-component tones against a broadband masking noise, in three binaural configurations (N0S180, N180S0, and N90S270). The thresholds for the 1-component stimuli were used to normalize the levels of each of the 5- and 17-component stimuli so that they were equally detectable. If equalization was restricted, then, for the 5- and 17-component stimuli, the N90S270 and N180S0 configurations would yield a greater threshold than the N0S180 configurations. No such difference was found. A subsequent experiment measured binaural detection thresholds, via psychometric functions, for a 2-component complex tone in the same three binaural configurations. Again, no differential effect of configuration was observed. An analytic model of the detection of a complex tone showed that the results were more consistent with free equalization than restricted equalization, although the size of the differences was found to depend on the shape of the psychometric function for detection.

Cis→Trans Isomerization of Pro7 in Oxytocin Regulates Zn2+ Binding

NASA Astrophysics Data System (ADS)

Fuller, Daniel R.; Glover, Matthew S.; Pierson, Nicholas A.; Kim, DoYong; Russell, David H.; Clemmer, David E.

2016-08-01

Ion mobility/mass spectrometry techniques are employed to investigate the binding of Zn2+ to the nine-residue peptide hormone oxytocin (OT, Cys1-Tyr2-Ile3-Gln4-Asn5-Cys6-Pro7-Leu8-Gly9-NH2, having a disulfide bond between Cys1 and Cys6 residues). Zn2+ binding to OT is known to increase the affinity of OT for its receptor [Pearlmutter, A. F., Soloff, M. S.: Characterization of the metal ion requirement for oxytocin-receptor interaction in rat mammary gland membranes. J. Biol. Chem. 254, 3899-3906 (1979)]. In the absence of Zn2+, we find evidence for two primary OT conformations, which arise because the Cys6-Pro7 peptide bond exists in both the trans- and cis-configurations. Upon addition of Zn2+, we determine binding constants in water of KA = 1.43 ± 0.24 and 0.42 ± 0.12 μM-1, for the trans- and cis-configured populations, respectively. The Zn2+ bound form of OT, having a cross section of Ω = 235 Å2, has Pro7 in the trans-configuration, which agrees with a prior report [Wyttenbach, T., Liu, D., Bowers, M. T.: Interactions of the hormone oxytocin with divalent metal ions. J. Am. Chem. Soc. 130, 5993-6000 (2008)], in which it was proposed that Zn2+ binds to the peptide ring and is further coordinated by interaction of the C-terminal, Pro7-Leu8-Gly9-NH2, tail. The present work shows that the cis-configuration of OT isomerizes to the trans-configuration upon binding Zn2+. In this way, the proline residue regulates Zn2+ binding to OT and, hence, is important in receptor binding.

Subcutaneous chronic implantable defibrillation systems in humans.

PubMed

Cappato, Riccardo; Smith, Warren M; Hood, Margaret A; Crozier, Ian G; Jordaens, Luc; Spitzer, Stefan G; Ardashev, Andrey V; Boersma, Lucas; Lupo, Pierpaolo; Grace, Andrew A; Bardy, Gust H

2012-09-01

The recent introduction of subcutaneous implantable cardioverter defibrillator (S-ICD) has raised attention about the potential of this technology for clinical use in daily clinical practice. We review the methods and results of the four studies conducted in humans for approval of this innovative technology for daily practice. Two studies using a temporary S-ICD system (acute human studies) were conducted to search for an appropriate lead configuration and energy requirements. For this purpose, 4 S-ICD configurations were tested in 78 patients at the time of transvenous (TV)-ICD implantation. The optimal configuration was tested in 49 more patients to comparatively assess the subcutaneous defibrillation threshold (S-DFT) versus the standard TV-ICD. Long-term implants were evaluated in 55 patients using an implanted system (chronic human study). The acute humans studies led to an optimal S-ICD configuration comprising a parasternal electrode and left anterolateral thoracic pulse generator. Both configurations successfully terminated 98% of induced ventricular fibrillation (VF), but significantly higher energy levels were required with S-ICD than with TV-ICD systems (36.6 ± 19.8 J vs. 11.1 ± 8.5 J). In the chronic study, all 137 VF episodes induced at time of implant were detected with a 98% conversion rate. Two pocket infections and four lead revisions were required during 10 ± 1 months of follow-up. During this period, survival was 98%, and 12 spontaneous ventricular tachyarrhythmias were detected and treated by the device. These data show that the S-ICD systems here consistently detected and converted VF induced at time of implant as well as sustained ventricular tachyarrhythmias occurring during follow-up (248).

Simulaid: a simulation facilitator and analysis program.

PubMed

Mezei, Mihaly

2010-11-15

Simulaid performs a large number of simulation-related tasks: interconversion and modification of structure and trajectory files, optimization of orientation, and a large variety of analysis functions. The program can handle structures in PDB (Berman et al., Nucleic Acids Res 2000, 28, 235), Charmm (Brooks et al., J Comput Chem 4, 187) CRD, Amber (Case et al.), Macromodel (Mohamadi et al., J Comput Chem 1990, 11, 440), Gromos/Gromacs (Hess et al.), InsightII (InsightII. Accelrys Inc.: San Diego, 2005), Grasp (Nicholls et al., Proteins: Struct Funct Genet 1991, 11, 281) .crg, Tripos (Tripos International, S. H. R., St. Louis, MO) .mol2 (input only), and in the MMC (Mezei, M.; MMC: Monte Carlo program for molecular assemblies. Available at: http://inka.mssm.edu/~mezei/mmc) formats; and trajectories in the formats of Charmm, Amber, Macromodel, and MMC. Analysis features include (but are not limited to): (1) simple distance calculations and hydrogen-bond analysis, (2) calculation of 2-D RMSD maps (produced both as text file with the data and as a color-coded matrix) and cross RMSD maps between trajectories, (3) clustering based on RMSD maps, (4) analysis of torsion angles, Ramachandran (Ramachandran and Sasiskharan, Adv Protein Chem 1968, 23, 283) angles, proline kink (Visiers et al., Protein Eng 2000, 13, 603) angles, pseudorotational (Altona and Sundaralingam, J Am Chem Soc 1972, 94, 8205; Cremer and Pople, J Am Chem Soc 1975, 97, 1354) angles, and (5) analysis based on circular variance (Mezei, J Mol Graphics Model 2003, 21, 463). Torsion angle evolutions are presented in dial plots (Ravishanker et al., J Biomol Struct Dyn 1989, 6, 669). Several of these features are unique to Simulaid. 2010 Wiley Periodicals, Inc.

Theory of electromagnetic wave propagation in ferromagnetic Rashba conductor

NASA Astrophysics Data System (ADS)

Shibata, Junya; Takeuchi, Akihito; Kohno, Hiroshi; Tatara, Gen

2018-02-01

We present a comprehensive study of various electromagnetic wave propagation phenomena in a ferromagnetic bulk Rashba conductor from the perspective of quantum mechanical transport. In this system, both the space inversion and time reversal symmetries are broken, as characterized by the Rashba field α and magnetization M, respectively. First, we present a general phenomenological analysis of electromagnetic wave propagation in media with broken space inversion and time reversal symmetries based on the dielectric tensor. The dependence of the dielectric tensor on the wave vector q and M is retained to first order. Then, we calculate the microscopic electromagnetic response of the current and spin of conduction electrons subjected to α and M, based on linear response theory and the Green's function method; the results are used to study the system optical properties. First, it is found that a large α enhances the anisotropic properties of the system and enlarges the frequency range in which the electromagnetic waves have hyperbolic dispersion surfaces and exhibit unusual propagations known as negative refraction and backward waves. Second, we consider the electromagnetic cross-correlation effects (direct and inverse Edelstein effects) on the wave propagation. These effects stem from the lack of space inversion symmetry and yield q-linear off-diagonal components in the dielectric tensor. This induces a Rashba-induced birefringence, in which the polarization vector rotates around the vector (α ×q ) . In the presence of M, which breaks time reversal symmetry, there arises an anomalous Hall effect and the dielectric tensor acquires off-diagonal components linear in M. For α ∥M , these components yield the Faraday effect for the Faraday configuration q ∥M and the Cotton-Mouton effect for the Voigt configuration ( q ⊥M ). When α and M are noncollinear, M- and q-induced optical phenomena are possible, which include nonreciprocal directional dichroism in the Voigt configuration. In these nonreciprocal optical phenomena, a "toroidal moment," α ×M , and a "quadrupole moment," αiMj+Miαj , play central roles. These phenomena are strongly enhanced at the spin-split transition edge in the electron band.

SPECIAL ISSUE ON OPTICAL PROCESSING OF INFORMATION: Transducers of physical fields based on two-channel coaxial optical fibres

NASA Astrophysics Data System (ADS)

Busurin, V. I.; Brazhnikova, T. Yu; Korobkov, V. V.; Prokhorov, N. I.

1995-10-01

An analysis is made of a general basic configuration and of the transfer function of a fibre-optic transducer based on controlled coupling in a multilayer two-channel coaxial optical fibre. The influence of the structure parameters and of external factors on the errors of a sensitive element in such a transducer is considered. The results are given of an investigation of the characteristics of a number of transducers constructed in accordance with the basic configuration.

Numerical Investigations of the Thermal, Pressure and Size Effects on 2D Spin Crossover Nanoparticles

NASA Astrophysics Data System (ADS)

Harlé, C.; Allal, S. E.; Sohier, D.; Dufaud, T.; Caballero, R.; de Zela, F.; Dahoo, P. R.; Boukheddaden, K.; Linares, J.

2017-12-01

In the framework of the Ising-like model, the thermal and pressure effects on the spin crossover systems are evaluated through two-states fictitious spin operators σ with eigenvalues 𝜎 = -1 and 𝜎 = +1 respectively associated with the low-spin (LS) and highspin (HS) states of each spin-crossover (SCO) molecule. Based on each configurational state, the macroscopic SCO system, is described by the following variables: m=Σ σi, s=Σ σi σj and c=Σ σk standing respectively for the total magnetization, the short-range correlations and surface magnetization. To solve this problem, we first determine the density of macrostates d[m][s][c], giving the number of microscopic configurations with the same m, s and c values. In this contribution, two different ways have been performed to calculate this important quantity: (i) the entropic sampling method, based on Monte Carlo simulations and (ii) a new algorithm based on specific dynamic programming. These two methods were tested on the 2D SCO nanoparticles for which, we calculated the average magnetization < σ> taking into account for short-, long-range interactions as well as for the interaction between surface molecules with their surrounding matrix. We monitored the effect of the pressure, temperature and size on the properties of the SCO nanoparticles.

Analysis of aeromedical retrieval coverage using elliptical isochrones: An evaluation of helicopter fleet size configurations in Scotland.

PubMed

Dodds, Naomi; Emerson, Philip; Phillips, Stephanie; Green, David R; Jansen, Jan O

2017-03-01

Trauma systems in remote and rural regions often rely on helicopter emergency medical services to facilitate access to definitive care. The siting of such resources is key, but often relies on simplistic modeling of coverage, using circular isochrones. Scotland is in the process of implementing a national trauma network, and there have been calls for an expansion of aeromedical retrieval capacity. The aim of this study was to analyze population and area coverage of the current retrieval service configuration, with three aircraft, and a configuration with an additional helicopter, in the North East of Scotland, using a novel methodology. Both overall coverage and coverage by physician-staffed aircraft, with enhanced clinical capability, were analyzed. This was a geographical analysis based on calculation of elliptical isochrones, which consider the "open-jaw" configuration of many retrieval flights. Helicopters are not always based at hospitals. We modeled coverage based on different outbound and inbound flights. Areally referenced population data were obtained from the Scottish Government. The current helicopter network configuration provides 94.2% population coverage and 59.0% area coverage. The addition of a fourth helicopter would marginally increase population coverage to 94.4% and area coverage to 59.1%. However, when considering only physician-manned aircraft, the current configuration provides only 71.7% population coverage and 29.4% area coverage, which would be increased to 91.1% and 51.2%, respectively, with a second aircraft. Scotland's current helicopter network configuration provides good population coverage for retrievals to major trauma centers, which would only be increased minimally by the addition of a fourth aircraft in the North East. The coverage provided by the single physician-staffed aircraft is more limited, however, and would be increased considerably by a second physician-staffed aircraft in the North East. Elliptical isochrones provide a useful means of modeling "open-jaw" retrieval missions and provide a more realistic estimate of coverage. Epidemiological study, level IV; therapeutic study, level IV.

Analysis of the EBT3 Gafchromic film irradiated with 6 MV photons and 6 MeV electrons using reflective mode scanners.

PubMed

Farah, Nicolas; Francis, Ziad; Abboud, Marie

2014-09-01

We explore in our study the effects of electrons and X-rays irradiations on the newest version of the Gafchromic EBT3 film. Experiments are performed using the Varian "TrueBeam 1.6" medical accelerator delivering 6 MV X-ray photons and 6 MeV electron beams as desired. The main interest is to compare the responses of EBT3 films exposed to two separate beams of electrons and photons, for radiation doses ranging up to 500 cGy. The analysis is done on a flatbed EPSON 10000 XL scanner and cross checked on a HP Scanjet 4850 scanner. Both scanners are used in reflection mode taking into account landscape and portrait scanning positions. After thorough verifications, the reflective scanning method can be used on EBT3 as an economic alternative to the transmission method which was also one of the goals of this study. A comparison is also done between single scan configuration including all samples in a single A4 (HP) or A3 (EPSON) format area and multiple scan procedure where each sample is scanned separately on its own. The images analyses are done using the ImageJ software. Results show significant influence of the scanning configuration but no significant differences between electron and photon irradiations for both single and multiple scan configurations. In conclusion, the film provides a reliable relative dose measurement method for electrons and photons irradiations in the medical field applications. Copyright © 2014 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Spectralon solar diffuser BRDF variation for NPP, JPSS J1 and J2

NASA Astrophysics Data System (ADS)

Murgai, Vijay; Johnson, Lindsay; Klein, Staci

2017-09-01

The Visible/Infrared Imaging Radiometer Suite (VIIRS) is a key sensor on the Suomi National Polar-orbiting Partnership (NPP) satellite as well as the upcoming Joint Polar Satellite System (JPSS). VIIRS collects Earth radiometric and imagery data in 22 spectral bands from 0.4 to 12.5 μm. Radiometric calibration of the reflective bands in the 0.4 to 2.5 μm wavelength range is performed by measuring the sunlight reflectance from Spectralon®. Reflected sun light is directly proportional to the Bidirectional Reflectance Distribution Function (BRDF) of the Spectralon. This paper presents the BRDF measurements of the Spectralon for JPSS J2 in the 0.4 - 1.63 μm wavelength using PASCAL (Polarization And Scatter Characterization Analysis of Lambertian materials) with an uncertainty better than 1.2%. PASCAL makes absolute measurements of the BRDF in an analogous fashion to the National Institute of Standards and Technology (NIST) Spectral Tri-function Automated Reflectance Reflectometer (STARR) facility. Unique additional features of this instrument include the ability to vary the sample elevation and roll / clock the sample about its normal, allowing measurement of BRDF in the as used geometry. Comparison of BRDF in the as used configuration for NPP, J1, and J2 shows variation of up to 3%. The sign of the change from panel to panel depends on the angle of incidence and view angle. The results demonstrate lot to lot variability in Spectralon and emphasize the necessity of characterizing each panel. A pattern in the BRDF variation is also presented.

J-Earth: An Essential Resource for Terrestrial Remote Sensing and Data Analysis

NASA Astrophysics Data System (ADS)

Dunn, S.; Rupp, J.; Cheeseman, S.; Christensen, P. R.; Prashad, L. C.; Dickenshied, S.; Anwar, S.; Noss, D.; Murray, K.

2011-12-01

There is a need for a software tool that has the ability to display and analyze various types of earth science and social data through a simple, user-friendly interface. The J-Earth software tool has been designed to be easily accessible for download and intuitive use, regardless of the technical background of the user base. This tool does not require courses or text books to learn to use, yet is powerful enough to allow a more general community of users to perform complex data analysis. Professions that will benefit from this tool range from geologists, geographers, and climatologists to sociologists, economists, and ecologists as well as policy makers. J-Earth was developed by the Arizona State University Mars Space Flight Facility as part of the JMARS (Java Mission-planning and Analysis for Remote Sensing) suite of open-source tools. The program is a Geographic Information Systems (GIS) application used for viewing and processing satellite and airborne remote sensing data. While the functionality of JMARS has historically focused on the research needs of the planetary science community, J-Earth has been designed for a much broader Earth-based user audience. NASA instrument products accessible within J-Earth include data from ASTER, GOES, Landsat, MODIS, and TIMS. While J-Earth contains exceptionally comprehensive and high resolution satellite-derived data and imagery, this tool also includes many socioeconomic data products from projects lead by international organizations and universities. Datasets used in J-Earth take the form of grids, rasters, remote sensor "stamps", maps, and shapefiles. Some highly demanded global datasets available within J-Earth include five levels of administrative/political boundaries, climate data for current conditions as well as models for future climates, population counts and densities, land cover/land use, and poverty indicators. While this application does share the same powerful functionality of JMARS, J-Earth's apperance is enhanced for much easier data analysis. J-Earth utilizes a layering system to view data from different sources which can then be exported, scaled, colored and superimposed for quick comparisons. Users may now perform spatial analysis over several diverse datasets with respect to a defined geographic area or the entire globe. In addition, several newly acquired global datasets contain a temporal dimension which when accessed through J-Earth, make this a unique and powerful tool for spatial analysis over time. The functionality and ease of use set J-Earth apart from all other terrestrial GIS software packages and enable endless social, political, and scientific possibilities

A project based on multi-configuration Dirac-Fock calculations for plasma spectroscopy

NASA Astrophysics Data System (ADS)

Comet, M.; Pain, J.-C.; Gilleron, F.; Piron, R.

2017-09-01

We present a project dedicated to hot plasma spectroscopy based on a Multi-Configuration Dirac-Fock (MCDF) code, initially developed by J. Bruneau. The code is briefly described and the use of the transition state method for plasma spectroscopy is detailed. Then an opacity code for local-thermodynamic-equilibrium plasmas using MCDF data, named OPAMCDF, is presented. Transition arrays for which the number of lines is too large to be handled in a Detailed Line Accounting (DLA) calculation can be modeled within the Partially Resolved Transition Array method or using the Unresolved Transition Arrays formalism in jj-coupling. An improvement of the original Partially Resolved Transition Array method is presented which gives a better agreement with DLA computations. Comparisons with some absorption and emission experimental spectra are shown. Finally, the capability of the MCDF code to compute atomic data required for collisional-radiative modeling of plasma at non local thermodynamic equilibrium is illustrated. In addition to photoexcitation, this code can be used to calculate photoionization, electron impact excitation and ionization cross-sections as well as autoionization rates in the Distorted-Wave or Close Coupling approximations. Comparisons with cross-sections and rates available in the literature are discussed.

Reactions of Copper and Silver Cations with Carbon Dioxide: An Infrared Photodissociation Spectroscopic and Theoretical Study.

PubMed

Zhao, Zhi; Kong, Xiangtao; Yang, Dong; Yuan, Qinqin; Xie, Hua; Fan, Hongjun; Zhao, Jijun; Jiang, Ling

2017-05-04

The reaction of copper and silver cations with carbon dioxide was studied by mass-selected infrared photodissociation spectroscopy. Quantum chemical calculations were performed on these products, which aided the experimental assignments of the infrared spectra and helped to elucidate the geometrical and electronic structures. The Cu + and Ag + cations bind to an oxygen atom of CO 2 in an end-on configuration via a charge-quadrupole electrostatic interaction in the [M(CO 2 ) n ] + complexes. The formation of oxide-carbonyl and carbonyl-carbonate structures is not favored for the interaction of CO 2 with Cu + and Ag + . For n = 3 and 4, the n + 0 structure is preferred. [Note on the nomenclature: Using i + j, i denotes the number of CO 2 molecules in the first coordination shell, and j denotes the number of CO 2 molecules in the second coordination shell.] The two nearly energy-identical n + 0 and (n - 1) + 1 structures coexist in n = 5 and 6. While the six-coordinated structure is favored for [Cu(CO 2 ) n=7,8 ] + , the n + 0 configuration is dominated in [Ag(CO 2 ) n=7,8 ] + . The reaction of CO 2 with the cationic metal atoms has been compared to that with the neutral and anionic metal atoms, which would have important implications for understanding the interaction of CO 2 with reduction catalysts and rationally designing catalysts for CO 2 reduction based on cost-effective transition metals.

Highly correlated configuration interaction calculations on water with large orbital bases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Almora-Díaz, César X., E-mail: xalmora@fisica.unam.mx

2014-05-14

A priori selected configuration interaction (SCI) with truncation energy error [C. F. Bunge, J. Chem. Phys. 125, 014107 (2006)] and CI by parts [C. F. Bunge and R. Carbó-Dorca, J. Chem. Phys. 125, 014108 (2006)] are used to approximate the total nonrelativistic electronic ground state energy of water at fixed experimental geometry with CI up to sextuple excitations. Correlation-consistent polarized core-valence basis sets (cc-pCVnZ) up to sextuple zeta and augmented correlation-consistent polarized core-valence basis sets (aug-cc-pCVnZ) up to quintuple zeta quality are employed. Truncation energy errors range between less than 1 μhartree, and 100 μhartree for the largest orbital set. Coupledmore » cluster CCSD and CCSD(T) calculations are also obtained for comparison. Our best upper bound, −76.4343 hartree, obtained by SCI with up to sextuple excitations with a cc-pCV6Z basis recovers more than 98.8% of the correlation energy of the system, and it is only about 3 kcal/mol above the “experimental” value. Despite that the present energy upper bounds are far below all previous ones, comparatively large dispersion errors in the determination of the extrapolated energies to the complete basis set do not allow to determine a reliable estimation of the full CI energy with an accuracy better than 0.6 mhartree (0.4 kcal/mol)« less

Laser-Induced Breakdown Spectroscopy for Detection of Explosives Residues: A Review of Recent Advances, Challenges, and Future Prospects

DTIC Science & Technology

2013-04-01

for discrimination [14, 15, 17]. Both Anzano et al . [18] and Tran et al . [21] analyzed the emission intensity ratios of several organic compounds for...A PC displays and ana- lyzes the recorded spectra, which are characteristic of the target material 284 J.L. Gottfried et al . The successful detection...energetic organic compounds 286 J.L. Gottfried et al . and experimental configuration. Several theoretical models have recently been developed to

Model Filled Polymers. 6. Determination of the Crosslink Density of Polymeric Beads by Swelling

DTIC Science & Technology

1990-08-22

7 References [1] M. Mooney , J. AppI. Phys., 11, 582 (1940). [2] R. S. Rivlin , and D. W. Sanders, Trans. Faraday Soc., 48, 200 (1952). [31 P. J. Flory...microbeads ranging in diameter from 0.2 to 1 p were prepared by emulsion polymerization in the absence of emulsifier [23]. Polytetrafluorethylene ( PTFE ...density of polymethyl methacrylate is 1.17 g/cm3 [201. Swelling A PTFE ultrafiltration membrane is weighed and inserted in a concave configuration

Design and analysis of multilayer x ray/XUV microscope

NASA Technical Reports Server (NTRS)

Shealy, David L.

1990-01-01

The design and analysis of a large number of normal incidence multilayer x ray microscopes based on the spherical mirror Schwarzschild configuration is examined. Design equations for the spherical mirror Schwarzschild microscopes are summarized and used to evaluate mirror parameters for microscopes with magnifications ranging from 2 to 50x. Ray tracing and diffraction analyses are carried out for many microscope configurations to determine image resolution as a function of system parameters. The results are summarized in three publication included herein. A preliminary study of advanced reflecting microscope configurations, where aspherics are used in place of the spherical microscope mirror elements, has indicated that the aspherical elements will improve off-axis image resolution and increase the effective field of view.

Data on the configuration design of internet-connected home cooling systems by engineering students.

PubMed

McComb, Christopher; Cagan, Jonathan; Kotovsky, Kenneth

2017-10-01

This experiment was carried out to record the step-by-step actions that humans take in solving a configuration design problem, either in small teams or individually. Specifically, study participants were tasked with configuring an internet-connected system of products to maintain temperature within a home, subject to cost constraints. Every participant was given access to a computer-based design interface that allowed them to construct and assess solutions. The interface was also used to record the data that is presented here. In total, data was collected for 68 participants, and each participant was allowed to perform 50 design actions in solving the configuration design problem. Major results based on the data presented here have been reported separately, including initial behavioral analysis (McComb et al.) [1], [2] and design pattern assessments via Markovian modeling (McComb et al., 2017; McComb et al., 2017) [3], [4].

Observations and light curve solutions of a selection of shallow-contact W UMa binaries

NASA Astrophysics Data System (ADS)

Kjurkchieva, Diana P.; Popov, Velimir A.; Vasileva, Doroteya L.; Petrov, Nikola I.

2018-07-01

Photometric observations in Sloan g‧ and i‧ bands of the W UMa binaries V0951 Per, CSS J062803.2+571604, CSS J222157.2+275308, CSS J075135.6+382028, V0338 Dra, NSVS 2256852, NSVS 4666412, V1355 Tau, NSVS 4808227, NSVS 4726498, CSS J075350.1+264830 and HL Lyn are presented. The light curve solutions revealed that these binaries have overcontact configurations with small fillout factors (within 0.1-0.2). Seven of them undergo total eclipses and their photometric mass ratios should be accepted with confidence. The temperature differences of the components of CSS J062803.2+571604 and NSVS 2256852 exceed 1100 K which is unusual for overcontact binaries. We suspect that NSVS 2256852 is a probable candidate for merger due to its small mass ratio of q = 0.16 and to the registered decreasing of the orbital period.

J-aggregation of a water-soluble tetracationic porphyrin in mixed LB films with a calix[8]arene carboxylic acid derivative.

PubMed

Miguel, Gustavo de; Pérez-Morales, Marta; Martín-Romero, María T; Muñoz, Eulogia; Richardson, Tim H; Camacho, Luis

2007-03-27

The molecular organization of a mixed film, containing a water-soluble tetracationic porphyrin (TMPyP) and a p-tert-butyl calix[8]arene octacarboxylic acid derivative (C8A), at the air-water interface and on a solid support (LB film), has been investigated. Although the TMPyP aggregation was not detected at the air-water interface, TMPyP J-aggregates have been found in the LB films (Y-type). Unlike tetraanionic porphyrins, for example TSPP, the TMPyP J-aggregates are not induced by a zwitterion formation. The TMPyP J-aggregation is a result of a "double comb" configuration, where porphyrins from opposite layers are interwoven in a linear infinite J-aggregate. Our results confirm that TMPyP molecules tend to self-aggregate strongly, provided the electrostatic repulsions of their peripheral groups are cancelled by the anionic groups of the C8A matrix.

Integration of XRootD into the cloud infrastructure for ALICE data analysis

NASA Astrophysics Data System (ADS)

Kompaniets, Mikhail; Shadura, Oksana; Svirin, Pavlo; Yurchenko, Volodymyr; Zarochentsev, Andrey

2015-12-01

Cloud technologies allow easy load balancing between different tasks and projects. From the viewpoint of the data analysis in the ALICE experiment, cloud allows to deploy software using Cern Virtual Machine (CernVM) and CernVM File System (CVMFS), to run different (including outdated) versions of software for long term data preservation and to dynamically allocate resources for different computing activities, e.g. grid site, ALICE Analysis Facility (AAF) and possible usage for local projects or other LHC experiments. We present a cloud solution for Tier-3 sites based on OpenStack and Ceph distributed storage with an integrated XRootD based storage element (SE). One of the key features of the solution is based on idea that Ceph has been used as a backend for Cinder Block Storage service for OpenStack, and in the same time as a storage backend for XRootD, with redundancy and availability of data preserved by Ceph settings. For faster and easier OpenStack deployment was applied the Packstack solution, which is based on the Puppet configuration management system. Ceph installation and configuration operations are structured and converted to Puppet manifests describing node configurations and integrated into Packstack. This solution can be easily deployed, maintained and used even in small groups with limited computing resources and small organizations, which usually have lack of IT support. The proposed infrastructure has been tested on two different clouds (SPbSU & BITP) and integrates successfully with the ALICE data analysis model.

A novel BCI based on ERP components sensitive to configural processing of human faces

NASA Astrophysics Data System (ADS)

Zhang, Yu; Zhao, Qibin; Jing, Jin; Wang, Xingyu; Cichocki, Andrzej

2012-04-01

This study introduces a novel brain-computer interface (BCI) based on an oddball paradigm using stimuli of facial images with loss of configural face information (e.g., inversion of face). To the best of our knowledge, till now the configural processing of human faces has not been applied to BCI but widely studied in cognitive neuroscience research. Our experiments confirm that the face-sensitive event-related potential (ERP) components N170 and vertex positive potential (VPP) have reflected early structural encoding of faces and can be modulated by the configural processing of faces. With the proposed novel paradigm, we investigate the effects of ERP components N170, VPP and P300 on target detection for BCI. An eight-class BCI platform is developed to analyze ERPs and evaluate the target detection performance using linear discriminant analysis without complicated feature extraction processing. The online classification accuracy of 88.7% and information transfer rate of 38.7 bits min-1 using stimuli of inverted faces with only single trial suggest that the proposed paradigm based on the configural processing of faces is very promising for visual stimuli-driven BCI applications.

A novel BCI based on ERP components sensitive to configural processing of human faces.

PubMed

Zhang, Yu; Zhao, Qibin; Jin, Jing; Wang, Xingyu; Cichocki, Andrzej

2012-04-01

This study introduces a novel brain-computer interface (BCI) based on an oddball paradigm using stimuli of facial images with loss of configural face information (e.g., inversion of face). To the best of our knowledge, till now the configural processing of human faces has not been applied to BCI but widely studied in cognitive neuroscience research. Our experiments confirm that the face-sensitive event-related potential (ERP) components N170 and vertex positive potential (VPP) have reflected early structural encoding of faces and can be modulated by the configural processing of faces. With the proposed novel paradigm, we investigate the effects of ERP components N170, VPP and P300 on target detection for BCI. An eight-class BCI platform is developed to analyze ERPs and evaluate the target detection performance using linear discriminant analysis without complicated feature extraction processing. The online classification accuracy of 88.7% and information transfer rate of 38.7 bits min(-1) using stimuli of inverted faces with only single trial suggest that the proposed paradigm based on the configural processing of faces is very promising for visual stimuli-driven BCI applications.

Highly Reusable Space Transportation (HRST) Baseline Concepts and Analysis: Rocket/RBCC Options. Part 2; A Comparative Study

NASA Technical Reports Server (NTRS)

Woodcock, Gordon

1997-01-01

This study is an extension of a previous effort by the Principal Investigator to develop baseline data to support comparative analysis of Highly Reusable Space Transportation (HRST) concepts. The analyses presented herin develop baseline data bases for two two-stage-to-orbit (TSTO) concepts: (1) Assisted horizontal take-off all rocket (assisted HTOHL); and (2) Assisted vertical take-off rocket based combined cycle (RBCC). The study objectives were to: (1) Provide configuration definitions and illustrations for assisted HTOHL and assisted RBCC; (2) Develop a rationalization approach and compare these concepts with the HRST reference; and (3) Analyze TSTO configurations which try to maintain SSTO benefits while reducing inert weight sensitivity.

Residual stress analysis of energy-dispersive diffraction data using a two-detector setup: Part I - Theoretical concept

NASA Astrophysics Data System (ADS)

Apel, Daniel; Meixner, Matthias; Liehr, Alexander; Klaus, Manuela; Degener, Sebastian; Wagener, Guido; Franz, Christian; Zinn, Wolfgang; Genzel, Christoph; Scholtes, Berthold

2018-01-01

A new goniometer setup for energy-dispersive X-ray diffraction is introduced which is based on simultaneous data acquisition with two detectors D1 and D2, both of them freely movable in a horizontal as well as in a vertical plane. From the multitude of measurement configurations that can be realised with this setup, we figured out three efficient concepts which aim at the fast analysis of residual stress depth profiles by combining the diffraction data gathered with the two detectors. The characteristic feature of the first two configurations consists in the vertical (horizontal) positioning of the first (second) detector, which results in a diffraction geometry where the two scattering vectors span a plane that coincides with the X-circle used for sample tilt. Because each detector does see the sample under another viewing angle, both the positive and the negative ψ-branch are covered by just one χ-tilt between 0°and 90°(configuration 1) and 0°and 60°(configuration 2), thus allowing for the simultaneous analysis of the in- and out-of-plane residual stress depth gradients σii(τ) and σi3(τ) (i = 1 , 2), respectively, from data sets dD1hkl(χ) and dD2hkl(χ). The third configuration introduced in this paper is based on a ϕ-rotation of the sample under a constant tilt angle χ and enables a fast and reliable tracing of shear stress fields σi3(τ) (i = 1, 2).

Na emission in the Hermean Exosphere as a tracer for particle precipitation dynamics

NASA Astrophysics Data System (ADS)

Orsini, Stefano; Mangano, Valeria; Plainaki, Christina; Mura, Alessandro; Milillo, Anna; Massetti, Stefano; De Angelis, Elisabetta; Rispoli, Rosanna; Lazzarotto, Francesco; Aronica, Alessandro

2017-04-01

In this presentation, we speculate on the Hermean exosphere Na hourly average distributions, as observed by the ground-based Themis solar telescope, and published by Mangano et al. ,2015 (*). From 2009 to 2013, we have selected 26 different days, when the Na signal was observed for 3 or more hours within each selected observation day, in good seeing conditions (sigma <2). We notice the occurrence of basically opposite configurations, i.e. i) when the sodium signal is localized above the poles, or ii) when it is diffused above the sub-solar region. Some time periods show also the existence of a transition phase between the two configurations. In order to identify these Na observations as possible tracers of particle precipitation patterns at Mercury, we compare these different Na emission configurations with the time profiles of particle and magnetic field data, as measured in-situ by MESSENGER, when such data were available. Within the analyzed time sequences, localized Na signals are more frequent ( 67% of cases), mostly linked to quiet IMF conditions. When the signal is more diffused, IMF data seem to indicate the occurrence of significant solar perturbations. The possible relationship between these events and the hermean magnetosphere general configuration is briefly discussed. (*) Mangano, V., Massetti, S., Milillo, A., Plainaki, C., Orsini, S., Rispoli, S. and Leblanc, F.: THEMIS Na exosphere observations of Mercury and their correlation with in-situ magnetic field measurements by MESSENGER. PSS, 115, 102-109, doy: 10.1016/j.pss.2015.04.001, 2015.

Flowfield Measurements in the Vortex Wake of a Missile at High Angle of Attack in Turbulence

DTIC Science & Technology

1988-12-01

pressure coefficient Cy: side force coefficient d: base diameter of the missile body F: blockage correction K: wind tunnel calibration factor LI : missile...and assistance in the wind tunnel apparatus and data acquisition s -;te1 m. I would like to thank Lt. Ao Chia-Ning. Republic of China Navy, Mr. Li ...axisymmetric missile configuration. 6- MO GRID + WIJS RE 1.33 E+05 z 2- Li 0- O C8 -C0 tq *tt~E I ’mtO0 E 5 , • r;.H/ 2 011USE 6 -6 x J! ’ 5SE 3 ,AHOSE

Retrieval of Shape Characteristics for Buried Objects with GPR Monitoring

NASA Astrophysics Data System (ADS)

Soldovieri, F.; Comite, D.; Galli, A.; Valerio, G.; Barone, P. M.; Lauro, S. E.; Mattei, E.; Pettinelli, E.

2012-04-01

Information retrieval on the location and the geometrical features (dimensions and shape) of buried objects is of fundamental importance in geosciences areas involving environmental protection, mine clearance, archaeological investigations, space and planetary exploration, and so forth. Among the different non-invasive sensing techniques usually employed to achieve this kind of information, those based on ground-penetrating-radar (GPR) instruments are well-established and suitable to the mentioned purposes [1]. In this context, our interest in the present work is specifically focused on testing the potential performance of typical GPR instruments by means of appropriate data processing. It will be shown in particular to what extent the use of a suitable "microwave tomographic approach" [2] is able to furnish a shape estimation of the targets, possibly recognizing different kinds of canonical geometries, even having reduced cross sections and in critical conditions, where the scatterer size is comparable with resolution limits imposed by the usual measurement configurations. Our study starts by obtaining the typical "direct" information from the GPR techniques that is the scattered field in subsurface environments under the form of radargrams. In order to get a wide variety of scenarios for the operating conditions, this goal is achieved by means of two different and independent approaches [3]. One approach is based on direct measurements through an experimental laboratory setup: commercial GPR instruments (typically bistatic configurations operating around 1 GHz frequency range) are used to collect radargram profiles by investigating an artificial basin filled of liquid and/or granular materials (sand, etc.), in which targets (having different constitutive parameters, shape, and dimensions) can be buried. The other approach is based on numerical GPR simulations by means of a commercial CAD electromagnetic tool (CST), whose suitable implementation and data processing allow us to retrieve results again in the form of radargrams for the scattering features of arbitrarily-composed subsurfaces. Once these types of "direct" (measured and/or simulated) radargram data are obtained, the "inverse" problem is then handled, based on a Born approximation to linearize the scattering problem. The targets are represented in terms of anomalies ("contrast function") of dielectric permittivity and conductivity with respect to the properties of a background environment. The analysis of the relevant results for the spatial distribution of the magnitude of the contrast function shows that, in various even-challenging practical cases, this kind of approach is able to properly locate buried objects, also identifying the relevant shape features. [1] D. J. Daniels (Ed.), Ground penetrating radar. IEE Press, 2004. [2] E. Pettinelli, A. Di Matteo, E. Mattei, L. Crocco, F. Soldovieri, J. D. Redman, and A. P. Annan, "GPR response from buried pipes: measurement on field site and tomographic reconstructions," IEEE Trans. Geosci. Remote Sensing, vol. 47, pp. 2639-2645, Aug. 2009. [3] G. Valerio, A. Galli, P. M. Barone, S. E. Lauro, E. Mattei, and E. Pettinelli, "GPR detectability of rocks in a Martian-like shallow subsoil: a numerical approach," Planet. Space Sci., 10 pp., doi: 10.1016/j.pss.2011.12.003, 2011.

Autonomous assembly with collision avoidance of a fleet of flexible spacecraft based on disturbance observer

NASA Astrophysics Data System (ADS)

Chen, Ti; Wen, Hao

2018-06-01

This paper presents a distributed control law with disturbance observer for the autonomous assembly of a fleet of flexible spacecraft to construct a large flexible space structure. The fleet of flexible spacecraft is driven to the pre-assembly configuration firstly, and then to the desired assembly configuration. A distributed assembly control law with disturbance observer is proposed by treating the flexible dynamics as disturbances acting on the rigid motion of the flexible spacecraft. Theoretical analysis shows that the control law can actuate the fleet to the desired configuration. Moreover, the collision avoidance between the members is also considered in the process from initial configuration to pre-assembly configuration. Finally, a numerical example is presented to verify the feasibility of proposed mission planning and the effectiveness of control law.

Multi-Scale Behavioral Modeling and Analysis Promoting a Fundamental Understanding of Agent-Based System Design and Operation

DTIC Science & Technology

2007-03-01

Chains," Mathematics of Control, Signals, and Systems, vol. 3(1), pp. 1-29, 1990. [4] A . Arnold, J . A . Carrillo, and I. Gamba, "Low and High Field...Aronson, C. L. A ., and J . L. Vázquez, "Interfaces with a corner point in one- dimensional porous medium flow," Comm. Pure Appl. Math, vol. 38(4), pp. 375...K. Levin, "Damage analysis of fiber composites," Computer Methods in Applied Mechanics and Engineering. [10] K. S. Barber, A . Goel, T. J . Graser, T

Conceptual design study of a nuclear Brayton turboalternator-compressor

NASA Technical Reports Server (NTRS)

1971-01-01

A comprehensive analysis and conceptual design study of the turboalternator-compressor components using HeXe as the working fluid was performed. The study was conducted in three phases: general configuration analysis (Phase 1), design variations (Phase 2), and conceptual design study (Phase 3). During the Phase 1 analysis, individual turbine, alternator, compressor, and bearing and seal designs were evaluated. Six turboalternator-compressor (TAC) configurations were completed. Phase 2 consisted of evaluating one selected Phase 1 TAC configuration to calculate its performance when operating under new cycle conditions, namely, one higher and one lower turbine inlet temperature and one case with krypton as the working fluid. Based on the Phase 1 and 2 results, a TAC configuration that incorporated a radial compressor, a radial turbine, a Lundell alternator, and gas bearings was selected. During Phase 3 a new layout of the TAC was prepared that reflects the cycle state points necessary to accommodate a zirconium hydride moderated reactor and a 400 Hz alternator. The final TAC design rotates at 24,000 rpm and produces 160 kWe, 480 V, 3-phase, 400 hertz power.

Exercise Type Affects Cardiac Vagal Autonomic Recovery After a Resistance Training Session.

PubMed

Mayo, Xián; Iglesias-Soler, Eliseo; Fariñas-Rodríguez, Juán; Fernández-Del-Olmo, Miguel; Kingsley, J Derek

2016-09-01

Mayo, X, Iglesias-Soler, E, Fariñas-Rodríguez, J, Fernández-del-Olmo, M, and Kingsley, JD. Exercise type affects cardiac vagal autonomic recovery after a resistance training session. J Strength Cond Res 30(9): 2565-2573, 2016-Resistance training sessions involving different exercises and set configurations may affect the acute cardiovascular recovery pattern. We explored the interaction between exercise type and set configuration on the postexercise cardiovagal withdrawal measured by heart rate variability and their hypotensive effect. Thirteen healthy participants (10 repetitions maximum [RM] bench press: 56 ± 10 kg; parallel squat: 91 ± 13 kg) performed 6 sessions corresponding to 2 exercises (Bench press vs. Parallel squat), 2 set configurations (Failure session vs. Interrepetition rest session), and a Control session of each exercise. Load (10RM), volume (5 sets), and rest (720 seconds) were equated between exercises and set configurations. Parallel squat produced higher reductions in cardiovagal recovery vs. Bench press (p = 0.001). These differences were dependent on the set configuration, with lower values in Parallel squat vs. Bench press for Interrepetition rest session (1.816 ± 0.711 vs. 2.399 ± 0.739 Ln HF/IRR × 10, p = 0.002), but not for Failure session (1.647 ± 0.904 vs. 1.808 ± 0.703 Ln HF/IRR × 10, p > 0.05). Set configuration affected the cardiovagal recovery, with lower values in Failure session in comparison with Interrepetition rest (p = 0.027) and Control session (p = 0.022). Postexercise hypotension was not dependent on the exercise type (p > 0.05) but was dependent on the set configuration, with lower values of systolic (p = 0.004) and diastolic (p = 0.011) blood pressure after the Failure session but not after an Interrepetition rest session in comparison with the Control session (p > 0.05). These results suggest that the exercise type and an Interrepetition rest design could blunt the decrease of cardiac vagal activity after exercise while exercising to muscular failure may contribute to the onset of postexercise hypotension.

Compositional partitioning during the spinodal decomposition in Cu-Ni-Sn alloy

NASA Astrophysics Data System (ADS)

Basak, C. B.; Poswal, A. K.

2018-05-01

Spinodal decomposition in Cu-9.4at%Ni-3.1at%Sn alloy was elucidated with the new insight from the experimental EXAFS analysis supported by ab initio total energy calculations suggesting the strong influence of the first near-neighbour atoms. Enthalpy of mixing was calculated for all crystallographically unique first near-neighbour configurations and finally an average positive enthalpy of mixing of 1604 J/mol was obtained. Combination of ab initio results, XRD and EXAFS analysis indicate that one of the daughter phase becomes rich in Ni and Sn than the other phase; in contrary to the earlier proposition that Cu/Ni ratio remains constant in both daughter phases. It is also shown that the present thermodynamic description requires further refinement to extend the miscibility gap towards lower Ni content in Cu-Ni-Sn system.

NASA Contractor Report: Guidelines for Proof Test Analysis

NASA Technical Reports Server (NTRS)

Chell, G. G.; McClung, R. C.; Kuhlman, C. J.; Russell, D. A.; Garr, K.; Donnelly, B.

1997-01-01

These Guidelines integrate state-of-the-art Elastic-Plastic Fracture Mechanics (EPFM) and proof test implementation issues into a comprehensive proof test analysis procedure in the form of a Road Map which identifies the types of data, fracture mechanics based parameters, and calculations needed to perform flaw screening and minimum proof load analyses of fracture critical components. Worked examples are presented to illustrate the application of the Road Map to proof test analysis. The state-of-the-art fracture technology employed in these Guidelines is based on the EPFM parameter, J, and a pictorial representation of a J fracture analysis, called the Failure Assessment Diagram (FAD) approach. The recommended fracture technology is validated using finite element J results, and laboratory and hardware fracture test results on the nickel-based superalloy IN-718, the aluminum alloy 2024-T351 1, and ferritic pressure vessel steels. In all cases the laboratory specimens and hardware failed by ductile mechanisms. Advanced proof test analyses involving probability analysis and Multiple Cycle Proof Testing (MCPT) are addressed. Finally, recommendations are provided on to how to account for the effects of the proof test overload on subsequent service fatigue and fracture behaviors.

External Aiding Methods for IMU-Based Navigation

DTIC Science & Technology

2016-11-26

Carlo simulation and particle filtering . This approach allows for the utilization of highly complex systems in a black box configuration with minimal...alternative method, which has the advantage of being less computationally demanding, is to use a Kalman filtering -based approach. The particular...Kalman filtering -based approach used here is known as linear covariance analysis. In linear covariance analysis, the nonlinear systems describing the

A New Ordered Si/SiO2 phase: Infrared Spectroscopy Analysis and Modeling

NASA Astrophysics Data System (ADS)

Bradley, J.; Herbots, N.; Shaw, J.; Atluri, V.; Queeney, K. T.; Chabal, Y. J.

2003-10-01

A new ordered Si/SiO2 phase is grown by conventional oxidation on ordered, OH-terminated (1x1)Si(100) surfaces formed at room temperature in ambient using a wet chemical cleaning method [1, 2] combined with conventional oxidation. Si atoms within 1-2.5 nm thick SiO2 are found to be in registry with respect to Si atoms in the Si(100). The degree of ordering is characterized by combining ion channeling with nuclear resonance analysis, as well as Reflective High Energy Electron Diffraction (RHEED), and High Resolution Transmission Electron Microscopy (HRTRM) and is found to be confined to a 2nm region in the SiO2[1]. Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) and Elastic Recoil Deflection (ERD) were used to profile silicon, oxygen, carbon, and hydrogen coverage within the ordered interphase. Most recently, infrared spectroscopy [2] was employed to investigate the bonding at the ordered Si/SiO2 interface and compare the suboxides region to conventional thermal oxides. Infrared spectroscopy shows that the TO red-shift due to SiOx cross-bonding at the Si/SiO2 interface is 50 % smaller and occurs more abruptly than in conventional thermal oxides. This indicates a more homogeneous bonding environment between Si and SiO2, which is consistent with the presence of an ordered phase. Using these results, we are modeling the structure of the 2 nm interphase with 3DSTRING [3]. This Monte Carlo Simulation enables us to compare the channeling spectra with the experimental data for the possible phase configuration in ordered SiOx on Si. [1] N. Herbots, V. Atluri, J. D. Bradley, J. Xiang, S. Banerjee, Q.Hurst, US Patent #6,613,677, Granted 9/2/2003 [2] N. Herbots, J. M. Shaw, Q. B. Hurst, M. P. Grams, R. J. Culbertson, D. J. Smith, V. Atluri, P. Zimmerman, and K. T. Queeney, Mat. Sci. Eng. B B87, 303-316 (2001). [3] K. T. Queeney, N. Herbots, Justin, M. Shaw, V. Atluri, Y. J. Chabal (to be published)

Discontinuous permeable adsorptive barrier design and cost analysis: a methodological approach to optimisation.

PubMed

Santonastaso, Giovanni Francesco; Bortone, Immacolata; Chianese, Simeone; Di Nardo, Armando; Di Natale, Michele; Erto, Alessandro; Karatza, Despina; Musmarra, Dino

2017-09-19

The following paper presents a method to optimise a discontinuous permeable adsorptive barrier (PAB-D). This method is based on the comparison of different PAB-D configurations obtained by changing some of the main PAB-D design parameters. In particular, the well diameters, the distance between two consecutive passive wells and the distance between two consecutive well lines were varied, and a cost analysis for each configuration was carried out in order to define the best performing and most cost-effective PAB-D configuration. As a case study, a benzene-contaminated aquifer located in an urban area in the north of Naples (Italy) was considered. The PAB-D configuration with a well diameter of 0.8 m resulted the best optimised layout in terms of performance and cost-effectiveness. Moreover, in order to identify the best configuration for the remediation of the aquifer studied, a comparison with a continuous permeable adsorptive barrier (PAB-C) was added. In particular, this showed a 40% reduction of the total remediation costs by using the optimised PAB-D.

Smoke-Point Properties of Non-Buoyant Round Laminar Jet Diffusion Flames. Appendix J

NASA Technical Reports Server (NTRS)

Urban, D. L.; Yuan, Z.-G.; Sunderland, P. B.; Lin, K.-C.; Dai, Z.; Faeth, G. M.

2000-01-01

The laminar smoke-point properties of non-buoyant round laminar jet diffusion flames were studied emphasizing results from long-duration (100-230 s) experiments at microgravity carried out in orbit aboard the space shuttle Columbia. Experimental conditions included ethylene- and propane-fueled flames burning in still air at an ambient temperature of 300 K, pressures of 35-130 kPa, jet exit diameters of 1.6 and 2.7 mm, jet exit velocities of 170-690 mm/s, jet exit Reynolds numbers of 46-172, characteristic flame residence times of 40-302 ms, and luminous flame lengths of 15-63 mm. Contrary to the normal-gravity laminar smoke point, in microgravity, the onset of laminar smoke-point conditions involved two flame configurations: closed-tip flames with soot emissions along the flame axis and open-tip flames with soot emissions from an annular ring about the flame axis. Open-tip flames were observed at large characteristic flame residence times with the onset of soot emissions associated with radiative quenching near the flame tip: nevertheless, unified correlations of laminar smoke-point properties were obtained that included both flame configurations. Flame lengths at laminar smoke-point conditions were well correlated in terms of a corrected fuel flow rate suggested by a simplified analysis of flame shape. The present steady and non-buoyant flames emitted soot more readily than non-buoyant flames in earlier tests using ground-based microgravity facilities and than buoyant flames at normal gravity, as a result of reduced effects of unsteadiness, flame disturbances, and buoyant motion. For example, present measurements of laminar smoke-point flame lengths at comparable conditions were up to 2.3 times shorter than ground-based microgravity measurements and up to 6.4 times shorter than buoyant flame measurements. Finally, present laminar smoke-point flame lengths were roughly inversely proportional to pressure to a degree that is a somewhat smaller than observed during earlier tests both at microgravity (using ground-based facilities) and at normal gravity.

Josephson Radiation from Gapless Andreev Bound States in HgTe-Based Topological Junctions

NASA Astrophysics Data System (ADS)

Deacon, R. S.; Wiedenmann, J.; Bocquillon, E.; Domínguez, F.; Klapwijk, T. M.; Leubner, P.; Brüne, C.; Hankiewicz, E. M.; Tarucha, S.; Ishibashi, K.; Buhmann, H.; Molenkamp, L. W.

2017-04-01

Frequency analysis of the rf emission of oscillating Josephson supercurrent is a powerful passive way of probing properties of topological Josephson junctions. In particular, measurements of the Josephson emission enable the detection of topological gapless Andreev bound states that give rise to emission at half the Josephson frequency fJ rather than conventional emission at fJ. Here, we report direct measurement of rf emission spectra on Josephson junctions made of HgTe-based gate-tunable topological weak links. The emission spectra exhibit a clear signal at half the Josephson frequency fJ/2 . The linewidths of emission lines indicate a coherence time of 0.3-4 ns for the fJ/2 line, much shorter than for the fJ line (3-4 ns). These observations strongly point towards the presence of topological gapless Andreev bound states and pave the way for a future HgTe-based platform for topological quantum computation.

Performance Analysis of the Enhanced Bio-Inspired Planning Algorithm for Rapid Situation Awareness Response

DTIC Science & Technology

2013-10-18

low cost robot testbed. 15. SUBJECT TERMS Bio-inspired trajectory generation, in-situ obstacle avoidance, low-cost LEGO robots, vision- based...will not affect the solution optimality and thus will be regarded as zero. Following the LP motion strategy Eq. (1), the position vector of the Lego ...Lobatto (LGL) method [14], the position of Lego robot can be further represented as ’ 1 ,( )j p jD   ζ ζ (6) in which ,0 ,,..., T j j j

A Factor Structure of Wellness: Theory, Assessment, Analysis, and Practice

ERIC Educational Resources Information Center

Hattie, John A.; Myers, Jane E.; Sweeney, Thomas J.

2004-01-01

The Wheel of Wellness, a theoretical model of well-being, incorporates 16 dimensions of healthy functioning that can be assessed using the Wellness Evaluation of Lifestyle (WEL; J. E. Myers, T. J. Sweeney, & J. M. Witmer, 1998). A series of studies are reported concerning the development and validation of the WEL based on a large database. In the…

Universal state-selective corrections to multireference coupled-cluster theories with single and double excitations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brabec, Jiri; van Dam, Hubertus JJ; Pittner, Jiri

2012-03-28

The recently proposed Universal State-Selective (USS) corrections [K. Kowalski, J. Chem. Phys. 134, 194107 (2011)] to approximate Multi-Reference Coupled Cluster (MRCC) energies can be commonly applied to any type of MRCC theory based on the Jeziorski-Monkhorst [B. Jeziorski, H.J. Monkhorst, Phys. Rev. A 24, 1668 (1981)] exponential Ansatz. In this letter we report on the performance of a simple USS correction to the Brillouin-Wigner MRCC (BW-MRCC) formalism employing single and double excitations (BW-MRCCSD). It is shown that the resulting formalism (USS-BW-MRCCSD), which uses the manifold of single and double excitations to construct the correction, can be related to a posteriorimore » corrections utilized in routine BW-MRCCSD calculations. In several benchmark calculations we compare the results of the USS-BW-MRCCSD method with results of the BW-MRCCSD approach employing a posteriori corrections and with results obtained with the Full Configuration Interaction (FCI) method.« less

A permutationally invariant full-dimensional ab initio potential energy surface for the abstraction and exchange channels of the H + CH{sub 4} system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Jun, E-mail: jli15@cqu.edu.cn, E-mail: zhangdh@dicp.ac.cn; Department of Chemistry and Chemical Biology, University of New Mexico, Albuquerque, New Mexico 87131; Chen, Jun

2015-05-28

We report a permutationally invariant global potential energy surface (PES) for the H + CH{sub 4} system based on ∼63 000 data points calculated at a high ab initio level (UCCSD(T)-F12a/AVTZ) using the recently proposed permutation invariant polynomial-neural network method. The small fitting error (5.1 meV) indicates a faithful representation of the ab initio points over a large configuration space. The rate coefficients calculated on the PES using tunneling corrected transition-state theory and quasi-classical trajectory are found to agree well with the available experimental and previous quantum dynamical results. The calculated total reaction probabilities (J{sub tot} = 0) including themore » abstraction and exchange channels using the new potential by a reduced dimensional quantum dynamic method are essentially the same as those on the Xu-Chen-Zhang PES [Chin. J. Chem. Phys. 27, 373 (2014)].« less

jFuzz: A Concolic Whitebox Fuzzer for Java

NASA Technical Reports Server (NTRS)

Jayaraman, Karthick; Harvison, David; Ganesh, Vijay; Kiezun, Adam

2009-01-01

We present jFuzz, a automatic testing tool for Java programs. jFuzz is a concolic whitebox fuzzer, built on the NASA Java PathFinder, an explicit-state Java model checker, and a framework for developing reliability and analysis tools for Java. Starting from a seed input, jFuzz automatically and systematically generates inputs that exercise new program paths. jFuzz uses a combination of concrete and symbolic execution, and constraint solving. Time spent on solving constraints can be significant. We implemented several well-known optimizations and name-independent caching, which aggressively normalizes the constraints to reduce the number of calls to the constraint solver. We present preliminary results due to the optimizations, and demonstrate the effectiveness of jFuzz in creating good test inputs. The source code of jFuzz is available as part of the NASA Java PathFinder. jFuzz is intended to be a research testbed for investigating new testing and analysis techniques based on concrete and symbolic execution. The source code of jFuzz is available as part of the NASA Java PathFinder.

Impact of Distributed Energy Resources on the Reliability of Critical Telecommunications Facilities: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, D. G.; Arent, D. J.; Johnson, L.

2006-06-01

This paper documents a probabilistic risk assessment of existing and alternative power supply systems at a large telecommunications office. The analysis characterizes the increase in the reliability of power supply through the use of two alternative power configurations. Failures in the power systems supporting major telecommunications service nodes are a main contributor to significant telecommunications outages. A logical approach to improving the robustness of telecommunication facilities is to increase the depth and breadth of technologies available to restore power during power outages. Distributed energy resources such as fuel cells and gas turbines could provide additional on-site electric power sources tomore » provide backup power, if batteries and diesel generators fail. The analysis is based on a hierarchical Bayesian approach and focuses on the failure probability associated with each of three possible facility configurations, along with assessment of the uncertainty or confidence level in the probability of failure. A risk-based characterization of final best configuration is presented.« less

Circuit analysis on the inductance evolution based on electrical signal from various type plasma focus device

NASA Astrophysics Data System (ADS)

Mohamad, Saiful Najmee; Ismail, Fairuz Diana; Noorden, Ahmad Fakhrurrazi Ahmad; Haider, Zuhaib; Ali, Jalil

2017-03-01

Numerous configurations of plasma focus devices (PFD) have been introduced around the globe. The distinct electrode configuration of the PFD will give out different inductance profile. A circuit analysis has been done to study on the significant difference between the inductance evolution in a coaxial discharge based on various published results of PFD. The discharge current signal, tube voltage and current derivative of the particular shots from distinct PFD was digitized and analyze. The investigation was piloted for three different types of PFD. It was observed that there is a significant difference for the normalize inductance profile during the discharge between the individual PFD with different electrode configuration. The depletion of the radial start current with the normalised inductance development for Mather type (PF-1000) is found to be 25.9% from static discharge. The current depletion continues to drop 1.1% and 1.3% more for a Spherical type (PNK-13) and Filippov type (PF-3) respectively.

Pairing and (9/2)n configuration in nuclei in the 208Pb region

NASA Astrophysics Data System (ADS)

Stepanov, M.; Imasheva, L.; Ishkhanov, B.; Tretyakova, T.

2018-04-01

Excited states in low-energy spectra in nuclei near 208Pb are considered. The pure (j = 9/2)n configuration approximation with delta-force is used for ground state multiplet calculations. The multiplet splitting is determined by the pairing energy, which can be defined from the even-odd straggering of the nuclear masses. For the configurations with more than two valence nucleons, the seniority scheme is used. The results of the calculations agree with the experimental data for both stable and exotic nuclei within 0.06-6.16%. Due to simplicity and absence of the fitted parameters, the model can be easily applied for studies of nature of the excited states in a wide range of nuclei.

Computational study for the effects of coil configuration on blood flow characteristics in coil-embolized cerebral aneurysm.

PubMed

Otani, Tomohiro; Ii, Satoshi; Shigematsu, Tomoyoshi; Fujinaka, Toshiyuki; Hirata, Masayuki; Ozaki, Tomohiko; Wada, Shigeo

2017-05-01

Coil embolization of cerebral aneurysms with inhomogeneous coil distribution leads to an incomplete occlusion of the aneurysm. However, the effects of this factor on the blood flow characteristics are still not fully understood. This study investigates the effects of coil configuration on the blood flow characteristics in a coil-embolized aneurysm using computational fluid dynamics (CFD) simulation. The blood flow analysis in the aneurysm with coil embolization was performed using a coil deployment (CD) model, in which the coil configuration was constructed using a physics-based simulation of the CD. In the CFD results, total flow momentum and kinetic energy in the aneurysm gradually decayed with increasing coil packing density (PD), regardless of the coil configuration attributed to deployment conditions. However, the total shear rate in the aneurysm was relatively high and the strength of the local shear flow varied based on the differences in coil configuration, even at adequate PDs used in clinical practice (20-25 %). Because the sufficient shear rate reduction is a well-known factor in the blood clot formation occluding the aneurysm inside, the present study gives useful insight into the effects of coil configuration on the treatment efficiency of coil embolization.

Validation of structural analysis methods using the in-house liner cyclic rigs

NASA Technical Reports Server (NTRS)

Thompson, R. L.

1982-01-01

Test conditions and variables to be considered in each of the test rigs and test configurations, and also used in the validation of the structural predictive theories and tools, include: thermal and mechanical load histories (simulating an engine mission cycle; different boundary conditions; specimens and components of different dimensions and geometries; different materials; various cooling schemes and cooling hole configurations; several advanced burner liner structural design concepts; and the simulation of hot streaks. Based on these test conditions and test variables, the test matrices for each rig and configurations can be established to verify the predictive tools over as wide a range of test conditions as possible using the simplest possible tests. A flow chart for the thermal/structural analysis of a burner liner and how the analysis relates to the tests is shown schematically. The chart shows that several nonlinear constitutive theories are to be evaluated.

Feasibility and electromagnetic analysis of a REBCO superconducting undulator

DOE PAGES

Kesgin, Ibrahim; Kasa, Matthew; Doose, Charles; ...

2016-03-17

Recent advances in second-generation (2G) high temperature superconducting (HTS) coated conductors (CCs) have made them very attractive for new applications such as undulators. In this study, we have, for the first time, experimentally evaluated a design to validate applicability of 2G-HTS tapes for next generation undulator magnetic structures. A two-period undulator magnetic core was fabricated and 2G-HTS CCs were successfully wound onto the undulator core. The performance of the undulator magnetic structure was investigated and the highest engineering current density, J e, in such configuration reported yet was obtained. A new U-slit tape configuration was used to reduce the numbermore » of resistive joints and it was shown that with this new technique affordable levels of resistance values can be achieved for short length undulators. The ferromagnetic core was designed such as to accommodate winding the U-slit tapes. Finally, test results indicated that the winding and the soldering procedures are successful and do not deteriorate the performance of the 2G-HTS tapes.« less

Airplane Actuation Trade Study

DTIC Science & Technology

1983-01-01

Actuation Loads 55 2.4.7 Actuation Configuration 55 2.4.6 Trade Study Aircraft 53 3.0 CONCLUSIONS AND RF.C(ILMJLA’IONS 3. 1 Conclusions 57 3.2 Reconmendat... 55 Final APU/EPU Configuration ........ .............. 236 I ix I.IST O11 TA.BLI:S Table Title Page 1. Vehicle Total Lifetime H ours Usage...were examined in some depth but were gradually eliminated as the study progressed. 55 4c= ICC o L La t-i •U - C I -~aJ U I- Ce- L~..-1 .z ~iC° C C) •bU

Coarse-grained model for colloidal protein interactions, B(22), and protein cluster formation.

PubMed

Blanco, Marco A; Sahin, Erinc; Robinson, Anne S; Roberts, Christopher J

2013-12-19

Reversible protein cluster formation is an important initial step in the processes of native and non-native protein aggregation, but involves relatively long time and length scales for detailed atomistic simulations and extensive mapping of free energy landscapes. A coarse-grained (CG) model is presented to semiquantitatively characterize the thermodynamics and key configurations involved in the landscape for protein oligomerization, as well as experimental measures of interactions such as the osmotic second virial coefficient (B22). Based on earlier work (Grüenberger et al., J. Phys. Chem. B 2013, 117, 763), this CG model treats proteins as rigid bodies composed of one bead per amino acid, with each amino acid having specific parameters for its size, hydrophobicity, and charge. The net interactions are a combination of steric repulsions, short-range attractions, and screened long-range charge-charge interactions. Model parametrization was done by fitting simulation results against experimental value of B22 as a function of solution ionic strength for α-chymotrypsinogen A and γD-Crystallin (gD-Crys). The CG model is applied to characterize the pairwise interactions and dimerization of gD-Crys and the dependence on temperature, protein concentration, and ionic strength. The results illustrate that at experimentally relevant conditions where stable dimers do not form, the entropic contributions are predominant in the free-energy of protein cluster formation and colloidal protein interactions, arguing against interpretations that treat B22 primarily from energetic considerations alone. Additionally, the results suggest that electrostatic interactions help to modulate the population of the different stable configurations for protein nearest-neighbor pairs, while short-range attractions determine the relative orientations of proteins within these configurations. Finally, simulation results are combined with Principal Component Analysis to identify those amino-acids/surface patches that form interprotein contacts at conditions that favor dimerization of gD-Crys. The resulting regions agree with previously found aggregation-prone sites, as well as suggesting new ones that may be important.

On the Morphology of a Growing City: A Heuristic Experiment Merging Static Economics with Dynamic Geography

PubMed Central

Delloye, Justin; Peeters, Dominique; Thomas, Isabelle

2015-01-01

In this paper, we aim at exploring how individual location decisions affect the shape of a growing city and, more precisely, how they may add up to a configuration that diverges from equilibrium configurations formulated ex-ante. To do so, we provide a two-sector city model merging a static equilibrium analysis with agent-based simulations. Results show that under strong agglomeration effects, urban development is monotonic and ends up with circular, monocentric long-term configurations. For low agglomeration effects however, elongated and multicentric urban configurations may emerge. The occurrence and underlying dynamics of these configurations are also discussed regarding commuting costs and the distance-decay of agglomeration economies between firms. To sum up, our paper warns urban planning policy makers against the difference that may stand between appropriate long-term perspectives, represented here by analytic equilibrium configurations, and short-term urban configurations, simulated here by a multi-agent system. PMID:26308858

GEODSS Present Configuration and Potential

DTIC Science & Technology

2014-06-28

to provide critical metric tracking capacity for deep space catalog maintenance. The follow-up TOS designed as a deployable gap filler in SSN deep...CASTOR) - A RAVEN System In Canada [3]WindowPane Observatory Lanphier Shutter System 2014 Retrieved From: http://windowpaneobservatory.com/ [4]J.N

Therminator: Configuring the Underlying Statistical Mechanics Model

DTIC Science & Technology

2003-12-01

1502, Oct. 7–10, 2002. [13] Ralph P . Grimaldi , Discrete and Combinational Mathematics, 4th Edition, Addison Wesley Longman, New York, 2000. [14...Eagle Co-Advisor John P . Powers Chairman, Department of Electrical and Computer Engineering Peter J. Denning Chairman, Department of...

VizieR Online Data Catalog: ALMA 106GHz continuum observations in Chamaeleon I (Dunham+, 2016)

NASA Astrophysics Data System (ADS)

Dunham, M. M.; Offner, S. S. R.; Pineda, J. E.; Bourke, T. L.; Tobin, J. J.; Arce, H. G.; Chen, X.; di, Francesco J.; Johnstone, D.; Lee, K. I.; Myers, P. C.; Price, D.; Sadavoy, S. I.; Schnee, S.

2018-02-01

We obtained ALMA observations of every source in Chamaleon I detected in the single-dish 870 μm LABOCA survey by Belloche et al. (2011, J/A+A/527/A145), except for those listed as likely artifacts (1 source), residuals from bright sources (7 sources), or detections tentatively associated with YSOs (3 sources). We observed 73 sources from the initial list of 84 objects identified by Belloche et al. (2011, J/A+A/527/A145). We observed the 73 pointings using the ALMA Band 3 receivers during its Cycle 1 campaign between 2013 November 29 and 2014 March 08. Between 25 and 27 antennas were available for our observations, with the array configured in a relatively compact configuration to provide a resolution of approximately 2" FWHM (300 AU at the distance to Chamaeleon I). Each target was observed in a single pointing with approximately 1 minute of on-source integration time. Three out of the four available spectral windows were configured to measure the continuum at 101, 103, and 114 GHz, each with a bandwidth of 2 GHz, for a total continuum bandwidth of 6 GHz (2.8 mm) at a central frequency of 106 GHz. (2 data files).

Differential heat of adsorption of water vapor on silicified microcrystalline cellulose (SMCC): an investigation using isothermal microcalorimetry.

PubMed

Qian, Ken K; Bogner, Robin H

2011-01-01

A novel dual-shaft configuration in isothermal microcalorimetry was developed to study the interaction of water vapor with pharmaceutical excipients. An instrument performance test is suggested to validate the experimental data. Reliable experimental results can be collected using a single perfusion shaft; however, there was limitation of the dual-shaft configuration, which resulted deviation in the experimental results. A periodic performance test is recommended. Silicified microcrystalline cellulose (SMCC) was used as a model system to study the interaction using the dual-shaft method. Enthalpy of water vapor adsorption on SMCC was determined and compared to literature data. The data collected using the dual-shaft configuration did not reflect the actual physical system. The deviation was most likely due to the lack of flow control caused by viscous resistance. The enthalpy of adsorption was then calculated using isothermal microcalorimetry coupled with a dynamic vapor sorption apparatus. The results, -55 kJ/mol at low relative humidity (RH) to -22 kJ/mol at high RH, were consistent with the physical phenomenon of water vapor adsorption. Enthalpy of adsorption showed surface heterogeneity of SMCC and suggested multilayer condensation of water at approximately 60% RH. However, at high RH, the results showed the moisture-excipient interaction can be more complex than the proposed mechanism.

Soft hairy warped black hole entropy

NASA Astrophysics Data System (ADS)

Grumiller, Daniel; Hacker, Philip; Merbis, Wout

2018-02-01

We reconsider warped black hole solutions in topologically massive gravity and find novel boundary conditions that allow for soft hairy excitations on the horizon. To compute the associated symmetry algebra we develop a general framework to compute asymptotic symmetries in any Chern-Simons-like theory of gravity. We use this to show that the near horizon symmetry algebra consists of two u (1) current algebras and recover the surprisingly simple entropy formula S = 2 π( J 0 + + J 0 - ), where J 0 ± are zero mode charges of the current algebras. This provides the first example of a locally non-maximally symmetric configuration exhibiting this entropy law and thus non-trivial evidence for its universality.

Magnitude and directional measures of water and Cr(VI) fluxes by passive flux meter.

PubMed

Campbell, Timothy J; Hatfield, Kirk; Klammler, Harald; Annable, Michael D; Rao, P S C

2006-10-15

A new configuration of the passive fluxmeter (PFM) is presented that provides for simultaneous measurements of both the magnitude and the direction of ambient groundwater specific discharge qo and Cr(VI) mass flux J(Cr). The PFM is configured as a cylindrical unit with an interior divided into a center section and three outer sectors, each packed with a granular anion exchange resin having high sorption capacity for the Cr(VI) oxyanions CrO4(2-) and HCrO4-. The sorbent in the center section is preloaded with benzoate as the "resident" tracer. Laboratory experiments were conducted in which PFMs were placed in porous packed bed columns, through which was passed a measured volume of synthetic groundwater containing Cr(VI). During the deployment period, some of the resident tracer is depleted while the Cr(VI) is sorbed. The resin was then removed from the four sectors separately and extracted to determine the "captured" mass of Cr(VI) and the residual mass of the resident tracer in each. Cumulative specific discharge, q0t, values were assessed using the residual mass of benzoate retained in the center section. The direction of this discharge theta was ascertained from the mass distribution of benzoate intercepted and retained in the outer three sections of the PFM. Cumulative chromium fluxes, J(Cr)t, were quantified using the total Cr(VI) mass intercepted and retained on the PFM. Experiments produced an average measurement error for direction theta of 3 degrees +/- 14 degrees, while the average measurement errors for q0 and J(Cr) were, respectively, -8% +/- 15% and -12% +/- 23%. Results demonstrate the potential utility of the new PFM configuration for characterizing groundwater and contaminant fluxes.

Monitoring 2-ethylhexyl-4-methoxycinnamate photoisomerization on skin using attenuated total reflection fourier transform infrared spectroscopy.

PubMed

Pangnakorn, P; Nonthabenjawan, R; Ekgasit, S; Thammacharoen, C; Pattanaargson Wanichwecharungruang, S

2007-02-01

Photoisomerization and photodimerization of a widely used UVB filter, 2-ethylhexy-4-methoxycinnamate (EHMC) on a ZnSe surface and baby mouse (Mus musculus Linn.) skin were monitored using attenuated total reflection Fourier transform infrared spectroscopy (ATR-FT-IR). Differentiation between the E- and the Z-EHMC could be achieved by examining the infrared (IR) peak at 981 cm(-1) (b peak), which corresponds to the CH rocking deformation vibration of Ph-CH=CH- detected only in the E configuration. By plotting the ratios of the peak area of the b peak and an internal standard peak (1060-998 cm(-1)) against mole percentage of Z-isomer in the E-Z mixtures, a linear calibration plot was obtained. Thus, a simple estimation of the mole percentage of each configuration in a sample was obtained. At the same UVB exposure, photostationary equilibrium of the E/Z isomerization on the surface varied with the applied amounts of EHMC. Photoisomerizations on ZnSe and on baby mouse skin were comparable. Less than 10% of E-EHMC changed configuration when the mouse skins applied with 1.0-4.0 mg/cm(2) E-EHMC were exposed to sunlight for 60 min (UVB radiant exposure of approximately 0.30 J/cm(2)). This corresponded to less than 5% loss in UV filtering efficiency. However, at a typical EHMC skin coverage ( approximately 0.2 mg/cm(2)), 0.30 J/cm(2) UVB exposure induced approximately 50% photoisomerization resulting in 25% loss of UV filtering efficiency. No photodimerization was detected even at the extreme EHMC coverage of 4.0 mg/cm(2) after a UVB exposure of 0.90 J/cm(2).

Space station system analysis study. Part 3: Documentation. Volume 2: Technical report. [structural design and construction

NASA Technical Reports Server (NTRS)

1977-01-01

An analysis of construction operation is presented as well as power system sizing requirements. Mission hardware requirements are reviewed in detail. Space construction base and design configurations are also examined.

Cost Analysis Sources and Documents Data Base Reference Manual (Update)

DTIC Science & Technology

1989-06-01

M: Refcrence Manual PRICE H: Training Course Workbook 11. Use in Cost Analysis. Important source of cost estimates for electronic and mechanical...Nature of Data. Contains many microeconomic time series by month or quarter. 5. Level of Detail. Very detailed. 6. Normalization Processes Required...Reference Manual. Moorestown, N.J,: GE Corporation, September 1986. 64. PRICE Training Course Workbook . Moorestown, N.J.: GE Corporation, February 1986

Structural analysis of two different stent configurations.

PubMed

Simão, M; Ferreira, J M; Mora-Rodriguez, J; Ramos, H M

2017-06-01

Two different stent configurations (i.e. the well known Palmaz-Schatz (PS) and a new stent configuration) are mechanically investigated. A finite element model was used to study the two geometries under combining loads and a computational fluid dynamic model based on fluid structure interaction was developed investigating the plaque and the artery wall reactions in a stented arterial segment. These models determine the stress and displacement fields of the two stents under internal pressure conditions. Results suggested that stent designs cause alterations in vascular anatomy that adversely affect arterial stress distributions within the wall, which have impact in the vessel responses such as the restenosis. The hemodynamic analysis shows the use of new stent geometry suggests better biofluid mechanical response such as the deformation and the progressive amount of plaque growth.

Application of ISSR markers to analyze molecular relationships in Iranian jasmine (Jasminum spp.) accessions.

PubMed

Ghasemi Ghehsareh, Masood; Salehi, Hassan; Khosh-Khui, Morteza; Niazi, Ali

2015-01-01

There are many species of jasmines in different regions of Iran in natural or cultivated form, and there is no information about their genetic status. Therefore, inter-simple sequence repeat (ISSR) analysis was used to evaluate genetic variations of the 53 accessions representing eight species of Jasminum collected from different regions of Iran. A total of 21 ISSR primers were used which generated 981 bands of different sizes. Mean percentage of polymorphic bands was 90.64 %. Maximum resolving power, polymorphic information content average, and marker index values were 21.55, 0.35, and 14.42 for primers of 3, 4, and 3 respectively. The unweighted pair group method with arithmetic mean dendrogram based on Jaccard's coefficients indicated that 53 accessions were divided into two major clusters. The first major cluster was divided into two subclusters; the subcluster A included Jasminum grandiflorum L., J. officinale L., and J. azoricum L. and the subcluster B consisted of three forms of J. sambac L. (single, semi-double, and double flowers). The second major cluster was divided into two subclusters; the first subcluster (C) included J. humile L., J. primulinum Hemsl., J. nudiflorum Lindl. and the second subcluster (D) consisted of J. fruticans L. At the species level, the highest percentage of polymorphism (34.05 %), numbers of effective alleles (1.16), Shannon index (0.151), and Nei's genetic diversity (0.098) were observed in J. officinale. The lowest values of percentage polymorphism (0.011), number of effective alleles (1.009), Shannon index (0.007), and Nei's genetic diversity (0.005) were obtained for J. nudiflorum. Based on pairwise population matrix of Nei's unbiased genetic identity, the highest identity (0.85) was found between J.officinale and J. azoricum and the lowest identity (0.69) was between J. grandiflorum and J. perimulinum. Based on analysis of molecular variance, the amount of genetic variations among the eight populations was 83 %. This study demonstrated that the ISSR is an useful tool in jasmine genomic diversity studies and to detect their relationships.

Rates of E1, E2, M1, and M2 transitions in Ni II

NASA Astrophysics Data System (ADS)

Cassidy, C. M.; Hibbert, A.; Ramsbottom, C. A.

2016-03-01

Aims: We present rates for all E1, E2, M1, and M2 transitions among the 295 fine-structure levels of the configurations 3d9, 3d84s, 3d74s2, 3d84p, and 3d74s4p, determined through an extensive configuration interaction calculation. Methods: The CIV3 code developed by Hibbert and coworkers is used to determine for these levels configuration interaction wave functions with relativistic effects introduced through the Breit-Pauli approximation. Results: Two different sets of calculations have been undertaken with different 3d and 4d functions to ascertain the effect of such variation. The main body of the text includes a representative selection of data, chosen so that key points can be discussed. Some analysis to assess the accuracy of the present data has been undertaken, including comparison with earlier calculations and the more limited range of experimental determinations. The full set of transition data is given in the supplementary material as it is very extensive. Conclusions: We believe that the present transition data are the best currently available. Full Table 4 and Tables 5-8 are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (ftp://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/587/A107

Trafficability of Soils

DTIC Science & Technology

1945-09-01

pressures as designated by tho Engineer Board Transportation Branch worexaod for all tost* with tha ex- ception of a few tests conduotod with low prossure...tentative values are based on conservative estimates. It is emphasised that the analysis and eonolu- ■ions «* de in this report are not entirely...E~a= dE —5 ! E = rr = = EiE: :=Zggc===== ,.]sii ’ 1 ,/’ J𔄃 g "yr ’" :MrJ - — M - —; L* i t< j«--. 4^ ------.H--. J

Using publically available forest inventory data in climate-based modes of tree species distribution: Examining effects of true versus altered location coordinates

Treesearch

Jacob Gibson; Gretchen Moisen; Tracey Frescino; Thomas C. Edwards

2013-01-01

Species distribution models (SDMs) were built with US Forest Inventory and Analysis (FIA) publicly available plot coordinates, which are altered for plot security purposes, and compared with SDMs built with true plot coordinates. Six species endemic to the western US, including four junipers (Juniperus deppeana var. deppeana, J. monosperma, J. occidentalis, J....

Temporal patterns of variable relationships in person-oriented research: longitudinal models of configural frequency analysis.

PubMed

von Eye, Alexander; Mun, Eun Young; Bogat, G Anne

2008-03-01

This article reviews the premises of configural frequency analysis (CFA), including methods of choosing significance tests and base models, as well as protecting alpha, and discusses why CFA is a useful approach when conducting longitudinal person-oriented research. CFA operates at the manifest variable level. Longitudinal CFA seeks to identify those temporal patterns that stand out as more frequent (CFA types) or less frequent (CFA antitypes) than expected with reference to a base model. A base model that has been used frequently in CFA applications, prediction CFA, and a new base model, auto-association CFA, are discussed for analysis of cross-classifications of longitudinal data. The former base model takes the associations among predictors and among criteria into account. The latter takes the auto-associations among repeatedly observed variables into account. Application examples of each are given using data from a longitudinal study of domestic violence. It is demonstrated that CFA results are not redundant with results from log-linear modeling or multinomial regression and that, of these approaches, CFA shows particular utility when conducting person-oriented research.

Comparison of microtweezers based on three lateral thermal actuator configurations

NASA Astrophysics Data System (ADS)

Luo, J. K.; Flewitt, A. J.; Spearing, S. M.; Fleck, N. A.; Milne, W. I.

2005-06-01

Thermal actuator-based microtweezers with three different driving configurations have been designed, fabricated and characterized. Finite element analysis has been used to model the device performance. It was found that one configuration of microtweezer, based on two lateral bimorph thermal actuators, has a small displacement (tip opening of the tweezers) and a very limited operating power range. An alternative configuration consisting of two horizontal hot bars with separated beams as the arms can deliver a larger displacement with a much-extended operating power range. This structure can withstand a higher temperature due to the wider beams used, and has flexible arms for increased displacement. Microtweezers driven by a number of chevron structures in parallel have similar maximum displacements but at a cost of higher power consumption. The measured temperature of the devices confirms that the device with the chevron structure can deliver the largest displacement for a given working temperature, while the bimorph thermal actuator design has the highest operating temperature at the same power due to its thin hot arm, and is prone to structural failure.

Space construction system analysis study: Project systems and missions descriptions

NASA Technical Reports Server (NTRS)

1979-01-01

Three project systems are defined and summarized. The systems are: (1) a Solar Power Satellite (SPS) Development Flight Test Vehicle configured for fabrication and compatible with solar electric propulsion orbit transfer; (2) an Advanced Communications Platform configured for space fabrication and compatible with low thrust chemical orbit transfer propulsion; and (3) the same Platform, configured to be space erectable but still compatible with low thrust chemical orbit transfer propulsion. These project systems are intended to serve as configuration models for use in detailed analyses of space construction techniques and processes. They represent feasible concepts for real projects; real in the sense that they are realistic contenders on the list of candidate missions currently projected for the national space program. Thus, they represent reasonable configurations upon which to base early studies of alternative space construction processes.

Spectroscopic study of the benchmark Mn+-H2 complex.

PubMed

Dryza, Viktoras; Poad, Berwyck L J; Bieske, Evan J

2009-05-28

We have recorded the rotationally resolved infrared spectrum of the weakly bound Mn+-H2 complex in the H-H stretch region (4022-4078 cm(-1)) by monitoring Mn+ photodissociation products. The band center of Mn+-H2, the H-H stretch transition, is shifted by -111.8 cm(-1) from the transition of the free H2 molecule. The spectroscopic data suggest that the Mn+-H2 complex consists of a slightly perturbed H2 molecule attached to the Mn+ ion in a T-shaped configuration with a vibrationally averaged intermolecular separation of 2.73 A. Together with the measured Mn+...H2 binding energy of 7.9 kJ/mol (Weis, P.; et al. J. Phys. Chem. A 1997, 101, 2809.), the spectroscopic parameters establish Mn+-H2 as the most thoroughly characterized transition-metal cation-dihydrogen complex and a benchmark for calibrating quantum chemical calculations on noncovalent systems involving open d-shell configurations. Such systems are of possible importance for hydrogen storage applications.

Collective opinion formation model under Bayesian updating and confirmation bias

NASA Astrophysics Data System (ADS)

Nishi, Ryosuke; Masuda, Naoki

2013-06-01

We propose a collective opinion formation model with a so-called confirmation bias. The confirmation bias is a psychological effect with which, in the context of opinion formation, an individual in favor of an opinion is prone to misperceive new incoming information as supporting the current belief of the individual. Our model modifies a Bayesian decision-making model for single individuals [M. Rabin and J. L. Schrag, Q. J. Econ.0033-553310.1162/003355399555945 114, 37 (1999)] for the case of a well-mixed population of interacting individuals in the absence of the external input. We numerically simulate the model to show that all the agents eventually agree on one of the two opinions only when the confirmation bias is weak. Otherwise, the stochastic population dynamics ends up creating a disagreement configuration (also called polarization), particularly for large system sizes. A strong confirmation bias allows various final disagreement configurations with different fractions of the individuals in favor of the opposite opinions.

Thermal analysis of injection beam dump of high-intensity rapid-cycling synchrotron in J-PARC

NASA Astrophysics Data System (ADS)

Kamiya, J.; Saha, P. K.; Yamamoto, K.; Kinsho, M.; Nihei, T.

2017-10-01

The beam dump at the beam injection area in the J-PARC 3-GeV rapid cycling synchrotron (RCS) accepts beams that pass through the charge exchange foil without ideal electron stripping during the multi-turn beam injection. The injection beam dump consists of the beam pipe, beam stopper, radiation shield, and cooling mechanism. The ideal beam power into the injection beam dump is 400 W in the case of design RCS extraction beam power of 1 MW with a healthy foil, which has 99.7 % charge stripping efficiency. On the other hand, as a radiation generator, the RCS is permitted to be operated with maximum average beam power of 4 kW into the injection beam dump based on the radiation shielding calculation, in consideration of lower charge stripping efficiency due to the foil deterioration. In this research, to evaluate the health of the RCS injection beam dump system from the perspective of the heat generation, a thermal analysis was performed based on the actual configuration with sufficiently large region, including the surrounding concrete and soil. The calculated temperature and heat flux density distribution showed the validity of the mesh spacing and model range. The calculation result showed that the dumped 4 kW beam causes the temperature to increase up to 330, 400, and 140 °C at the beam pipe, beam stopper, and radiation shield, respectively. Although these high temperatures induce stress in the constituent materials, the calculated stress values were lower than the ultimate tensile strength of each material. Transient temperature analysis of the beam stopper, which simulated the sudden break of the charge stripper foil, demonstrated that one bunched beam pulse with the maximum beam power does not lead to a serious rise in the temperature of the beam stopper. Furthermore, from the measured outgassing rate of stainless steel at high temperature, the rise in beam line pressure due to additive outgassing from the heated beam pipe was estimated to have a negligible effect on beam line pressure. The flow and results of the evaluation in this analysis would provide a good indication for both the verification of the existing beam dumps, and the design of beam dumps in new accelerators with higher intensity beam.

Extensive computation of allowed and forbidden transition probabilities in the potassium isoelectronic sequence

NASA Astrophysics Data System (ADS)

Dixit, Gopal; Deshmukh, Pranawa C.; Manson, Steven T.; Majumder, Sonjoy

2007-06-01

Our primary aim in this work is to present both allowed and forbidden transition amplitudes and corresponding wavelengths and oscillator strengths for a few ions in the 19-electron potassium isoelectronic sequence. All of these ions have the configuration [Ar] 3^2D3/2 as their ground state, except in the case of K and Ca^+, where it is [Ar] 4^2S1/2.This difference in ground state configuration arises due to strong contributions of correlation effects in the energy levels of these systems [1]. Allowed and forbidden transitions in these systems are of great importance in astrophysics [2] and in laboratory plasma research [3]. We apply in the present work the relativistic coupled-cluster (RCC) theory [4] to evaluate the energy levels and wave functions of these systems and study amplitudes for electric and magnetic dipole transition amplitudes and also the electric quadrupole transition amplitudes. The contributions of various electron correlation effects to the transition amplitudes are estimated in some detail using the RCC theory. [1] Gopal Dixit et al., Astrophys. J (submitted); arXiv.org: physics/0702066. [2] C. R. Cowley and G. M. Wahlgern, Astronomy & Astrophysics, 447, 681 (2002). [3] J. E. Vernazza, E. M. Reeves, Astrophys. J. Suppl. 37, 485 (1978) [4] I. Lindgren, Physics Scripta, 36, 591 (1987).

Aerodynamic Analysis of the Truss-Braced Wing Aircraft Using Vortex-Lattice Superposition Approach

NASA Technical Reports Server (NTRS)

Ting, Eric Bi-Wen; Reynolds, Kevin Wayne; Nguyen, Nhan T.; Totah, Joseph J.

2014-01-01

The SUGAR Truss-BracedWing (TBW) aircraft concept is a Boeing-developed N+3 aircraft configuration funded by NASA ARMD FixedWing Project. This future generation transport aircraft concept is designed to be aerodynamically efficient by employing a high aspect ratio wing design. The aspect ratio of the TBW is on the order of 14 which is significantly greater than those of current generation transport aircraft. This paper presents a recent aerodynamic analysis of the TBW aircraft using a conceptual vortex-lattice aerodynamic tool VORLAX and an aerodynamic superposition approach. Based on the underlying linear potential flow theory, the principle of aerodynamic superposition is leveraged to deal with the complex aerodynamic configuration of the TBW. By decomposing the full configuration of the TBW into individual aerodynamic lifting components, the total aerodynamic characteristics of the full configuration can be estimated from the contributions of the individual components. The aerodynamic superposition approach shows excellent agreement with CFD results computed by FUN3D, USM3D, and STAR-CCM+.

Nose-to-tail analysis of an airbreathing hypersonic vehicle using an in-house simplified tool

NASA Astrophysics Data System (ADS)

Piscitelli, Filomena; Cutrone, Luigi; Pezzella, Giuseppe; Roncioni, Pietro; Marini, Marco

2017-07-01

SPREAD (Scramjet PREliminary Aerothermodynamic Design) is a simplified, in-house method developed by CIRA (Italian Aerospace Research Centre), able to provide a preliminary estimation of the performance of engine/aeroshape for airbreathing configurations. It is especially useful for scramjet engines, for which the strong coupling between the aerothermodynamic (external) and propulsive (internal) flow fields requires real-time screening of several engine/aeroshape configurations and the identification of the most promising one/s with respect to user-defined constraints and requirements. The outcome of this tool defines the base-line configuration for further design analyses with more accurate tools, e.g., CFD simulations and wind tunnel testing. SPREAD tool has been used to perform the nose-to-tail analysis of the LAPCAT-II Mach 8 MR2.4 vehicle configuration. The numerical results demonstrate SPREAD capability to quickly predict reliable values of aero-propulsive balance (i.e., net-thrust) and aerodynamic efficiency in a pre-design phase.

An analysis of the effect of lower extremity strength on impact severity during a backward fall.

PubMed

Sandler, R; Robinovitch, S

2001-12-01

At least 280 000 hip fractures occur annually in the U.S. at an estimated cost of $9 billion. While over 90 percent of these are caused by falls, only about 2 percent of all falls result in hip fracture. Evidence suggests that the most important determinants of hip fracture risk during a fall are the body's impact velocity and configuration. Accordingly, protective responses for reducing impact velocity and the likelihood for direct impact to the hip, strongly influence fracture risk. One method for reducing the body's impact velocity and kinetic energy during a fall is to absorb energy in the lower extremity muscles during descent, as occurs during sitting and squatting. In the present study, we employed a series of in verted pendulum models to determine: (a) the theoretical effect of this mechanism on impact severity during a backward fall, and (b) the effect on impact severity of age-related declines (or exercise-induced enhancements) in lower extremity strength. Compared to the case of a fall with zero energy absorption in the lower extremity joints, best-case falls (which involved 81 percent activation of ankle and hip muscles, but only 23 percent activation of knees muscles) involved 79 percent attenuation (from 352 J to 74 J) in the body's vertical kinetic energy at impact (KEv), and 48 percent attenuation (from 3.22 to 1.68 m/s) in the downward velocity of the pelvis at impact (v(v)). Among the mechanisms responsible for this were: (1) eccentric contraction of lower extremity muscles during descent, which resulted in up to 150 J of energy absorption; (2) impact with the trunk in an upright configuration, which reduced the change in potential energy associated with the fall by 100 J; and (3) knee extension during the final stage of descent, which "transferred" up to 90 J of impact energy into horizontal (as opposed to vertical) kinetic energy. Declines in joint strength reduced the effectiveness of mechanisms (1) and (3), and thereby increased impact severity However, even with reductions of 80 percent in available torques, KEv was attenuated by 50 percent. This indicates the importance of both technique and strength in reducing impact severity. These results provide motivation for attempts to reduce elderly individuals' risk for fall-related injury through the combination of instruction in safe falling techniques and exercises that enhance lower extremity strength.

Recent advances in quartz enhanced photoacoustic sensing

NASA Astrophysics Data System (ADS)

Patimisco, Pietro; Sampaolo, Angelo; Dong, Lei; Tittel, Frank K.; Spagnolo, Vincenzo

2018-03-01

This review aims to discuss the latest advancements in quartz-enhanced photoacoustic spectroscopy (QEPAS) based trace-gas sensing. Starting from the QEPAS basic physical principles, the most used QEPAS configurations will be described. This is followed by a detailed theoretical analysis and experimental study regarding the influence of quartz tuning forks (QTFs) geometry on their optoacoustic transducer performance. Furthermore, an overview of the latest developments in QEPAS trace-gas sensor technology employing custom QTFs will be reported. Results obtained by exploiting novel micro-resonator configurations, capable of increasing the QEPAS signal-to-noise ratio by more than two orders of magnitude and the utilization of QTF overtone flexural modes for QEPAS based sensing will be presented. A comparison of the QEPAS performance of different spectrophone configurations is reported based upon signal-to-noise ratio. Finally, a novel QEPAS approach allowing simultaneous dual-gas detection will be described.

Visualizing Uncertainty for Probabilistic Weather Forecasting based on Reforecast Analogs

NASA Astrophysics Data System (ADS)

Pelorosso, Leandro; Diehl, Alexandra; Matković, Krešimir; Delrieux, Claudio; Ruiz, Juan; Gröeller, M. Eduard; Bruckner, Stefan

2016-04-01

Numerical weather forecasts are prone to uncertainty coming from inaccuracies in the initial and boundary conditions and lack of precision in numerical models. Ensemble of forecasts partially addresses these problems by considering several runs of the numerical model. Each forecast is generated with different initial and boundary conditions and different model configurations [GR05]. The ensembles can be expressed as probabilistic forecasts, which have proven to be very effective in the decision-making processes [DE06]. The ensemble of forecasts represents only some of the possible future atmospheric states, usually underestimating the degree of uncertainty in the predictions [KAL03, PH06]. Hamill and Whitaker [HW06] introduced the "Reforecast Analog Regression" (RAR) technique to overcome the limitations of ensemble forecasting. This technique produces probabilistic predictions based on the analysis of historical forecasts and observations. Visual analytics provides tools for processing, visualizing, and exploring data to get new insights and discover hidden information patterns in an interactive exchange between the user and the application [KMS08]. In this work, we introduce Albero, a visual analytics solution for probabilistic weather forecasting based on the RAR technique. Albero targets at least two different type of users: "forecasters", who are meteorologists working in operational weather forecasting and "researchers", who work in the construction of numerical prediction models. Albero is an efficient tool for analyzing precipitation forecasts, allowing forecasters to make and communicate quick decisions. Our solution facilitates the analysis of a set of probabilistic forecasts, associated statistical data, observations and uncertainty. A dashboard with small-multiples of probabilistic forecasts allows the forecasters to analyze at a glance the distribution of probabilities as a function of time, space, and magnitude. It provides the user with a more accurate measure of forecast uncertainty that could result in better decision-making. It offers different level of abstractions to help with the recalibration of the RAR method. It also has an inspection tool that displays the selected analogs, their observations and statistical data. It gives the users access to inner parts of the method, unveiling hidden information. References [GR05] GNEITING T., RAFTERY A. E.: Weather forecasting with ensemble methods. Science 310, 5746, 248-249, 2005. [KAL03] KALNAY E.: Atmospheric modeling, data assimilation and predictability. Cambridge University Press, 2003. [PH06] PALMER T., HAGEDORN R.: Predictability of weather and climate. Cambridge University Press, 2006. [HW06] HAMILL T. M., WHITAKER J. S.: Probabilistic quantitative precipitation forecasts based on reforecast analogs: Theory and application. Monthly Weather Review 134, 11, 3209-3229, 2006. [DE06] DEITRICK S., EDSALL R.: The influence of uncertainty visualization on decision making: An empirical evaluation. Springer, 2006. [KMS08] KEIM D. A., MANSMANN F., SCHNEIDEWIND J., THOMAS J., ZIEGLER H.: Visual analytics: Scope and challenges. Springer, 2008.

High power green lasers for gamma source

NASA Astrophysics Data System (ADS)

Durand, Magali; Sevillano, Pierre; Alexaline, Olivier; Sangla, Damien; Casanova, Alexis; Aubourg, Adrien; Saci, Abdelhak; Courjaud, Antoine

2018-02-01

A high intensity Gamma source is required for Nuclear Spectroscopy, it will be delivered by the interaction between accelerated electron and intense laser beams. Those two interactions lasers are based on a multi-stage amplification scheme that ended with a second harmonics generation to deliver 200 mJ, 5 ps pulses at 515 nm and 100 Hz. A t-Pulse oscillator with slow and fast feedback loop implemented inside the oscillator cavity allows the possibility of synchronization to an optical reference. A temporal jitter of 120 fs rms is achieved, integrated from 10 Hz to 10 MHz. Then a regenerative amplifier, based on Yb:YAG technology, pumped by fiber-coupled QCW laser diodes, delivers pulses up to 30 mJ. The 1 nm bandwidth was compressed to 1.5 ps with a good spatial quality: M2 of 1.1. This amplifier is integrated in a compact sealed housing (750 x 500 x 150 mm), which allows a pulse-pulse stability of 0.1 % rms, and a long-term stability of 1,9 % over 100 hours (with +/-1°C environment). The main amplification stage uses a cryocooled Yb:YAG crystal in an active mirror configuration. The crystal is cooled at 130 K via a compact and low-vibration cryocooler, avoiding any additional phase noise contribution, 340 mJ in a six pass scheme was achieved, with 0.9 of Strehl ratio. The trade off to the gain of a cryogenic amplifier is the bandwidth reduction, however the 1030 nm pulse was compressed to 4.4 ps. As for the regenerative amplifier a long-term stability of 1.9 % over 30 hours was achieved in an environment with +/-1°C temperature fluctuations The compression and Second Harmonics Generation Stages have allowed the conversion of 150 mJ of uncompressed infrared beam into 60 mJ at 515 nm.

The validity of transverse intermaxillary analysis by traditional PA cephalometry compared with cone-beam computed tomography.

PubMed

Cheung, Gordon; Goonewardene, Mithran Suresh; Islam, Syed Mohammed Shamsul; Murray, Kevin; Koong, Bernard

2013-05-01

To assess the validity of using jugale (J) and Antegonion (Ag) on Posterior-Anterior cephalograms (PAC) as landmarks for transverse intermaxillary analysis when compared with Cone Beam Computed Tomography (CBCT). Conventional PAC and CBCT images were taken of 28 dry skulls. Craniometric measurements between the bilateral landmarks, Antegonion and Jugale, were obtained from the skulls using a microscribe and recorded as the base standard. The corresponding andmarks were identified and measured on CBCT and PAC and compared with the base standard measurements. The accuracy and reliability of the measurements were statistically evaluated and the validity was assessed by comparing the ability of the two image modalities to accurately diagnose an arbitrarily selected J-J/Ag-Ag ratio. All measurements were repeated at least 7 weeks apart. Intra-class correlations (ICC) and Bland-Altman plots were used to analyse the data. All three methods were shown to be reliable as all had a mean error of less than 0.5 mm between repeated measurements. When compared with the base standard, CBCT measurements were shown to have higher agreement (ICC: 0.861-0.964) compared with measurements taken from PAC (ICC: 0.794-0.796). When the arbitrary J-J/Ag-Ag ratio was assessed, 18 per cent of cases were incorrectly diagnosed with a transverse discrepancy on the PAC compared with the CBCT which incorrectly diagnosed 8.7 per cent. CBCT was shown to be more reliable in assessing intermaxillary transverse discrepancy compared with PAC when using J-J/Ag-Ag ratios.

77 FR 35978 - Johnson & Johnson and Synthes, Inc.; Analysis of Agreement Containing Consent Orders to Aid...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-15

... the most common fractures in the human body. Distal radius fractures generally occur as a result of an... comprehensive and broad-based manufacturer of products related to all aspects of human health care. In 2011, J&J...

Internal nasal floor configuration in Homo with special reference to the evolution of Neandertal facial form.

PubMed

Franciscus, Robert G

2003-06-01

The presence of a steeply sloping or depressed nasal floor within the nasal cavity of Neandertals is frequently mentioned as a likely specialization or autapomorphy. The depressed nasal floor has also been seen as contributing to a relatively more capacious nasal cavity in Neandertals, which is tied to cold-climate respiratory adaptation and energetics. These observations have been limited largely to a relatively few intact crania, and the character states associated with this trait have not been as precisely codified or analyzed as those published for Plio-Pleistocene hominins (McCollum et al., 1993, J. Hum. Evol. 24, 87; McCollum, 2000, Am. J. Phys. Anthrop. 112, 275). This study examines the internal nasal floor topography in complete crania and isolated maxillae in European, west Asian, and African fossil Homo (n=158) including 25 Neandertals, and a wide range of recent humans from Europe, the Near East, and Africa (n=522). The configuration of the internal nasal floor relative to the nasal cavity entrance is codified as: 1) level, forming a smooth continuous plane; 2) sloped or mildly stepped; or 3) bilevel with a pronounced vertical depression. The frequency of these nasal floor configurations, and their relationship to both nasal margin cresting patterning and a comprehensive set of nasofacial metrics is examined. Neandertals show a high frequency of the bilevel (depressed) configuration in both adults and subadults (80%), but this configuration is also present in lower frequencies in Middle Pleistocene African, Late Pleistocene non-Neandertal (Skhul, Qafzeh), and European Later Upper Paleolithic samples (15%-50%). The bilevel configuration is also present in lower frequencies (ca. 10%) in all recent human samples, but attains nearly 20% in some sub-Saharan African samples. Across extinct and extant Homo (excluding Neandertals), internal nasal floor configuration is not associated with piriform aperture nasal margin patterning, but the two are strongly linked in Neandertals. Variation in internal nasal floor configuration in recent humans is primarily associated with internal nasal fossa breadth and nasal bridge elevation, whereas in fossil hominins, it is associated primarily with variation in facial height. Cold-climate and activity-related thermal adaptation as an explanation for the high frequency of pronounced nasal floor depression in Neandertals is inconsistent with all available data. Alternatively, variation in internal nasal floor configuration is more likely related to stochastically derived populational differences in fetal nasofacial growth patterns that do not sharply differentiate genus Homo taxa (i.e., cladistically), but do phenetically differentiate groups, in particular the Neandertals, especially when considered in combination with other nasofacial features.

Investigation of Rotating Stall Phenomena in Axial Flow Compressors. Volume I. Basic Studies of Rotating Stall

DTIC Science & Technology

1976-06-01

rotating stall control system which was tested both on a low speed rig and a J-85-S engine. The second objective was to perform fundamental studies of the...Stator Stage 89 6 Annular Cascade Configuration Used for Rotating Stall Studies on Rotoi-Stator Stage ..... .............. ... 90 7 Static Pressure Rise...ground tests on a J-8S-S turbojet engine. The work i3 reported in three separate volumes. Volume I entitled, "Basic Studies of Rotating Stall", covers

Multi-Domain Assembly of Nuclear Estrogen Receptors: Structural Insights into ER-Positive Breast Cancer Therapeutics

DTIC Science & Technology

2013-04-01

configurations in the top 25% and 30% of all unbiased simulations were also projected onto the energy globe [Fig. S3(B)]. These results show that each...Coarse-grained simulations of protein-protein association: An energy landscape perspective. Biophys J 103(4):837 – 845, 2012. 27. Yang, S., Onuchic, J. N...S1. The projected snapshots were taken only from free and released portions of PPR simulation cycles with a energy cutoff of ELBD−DBD < 0 kcal/mol and

Individual-Ion Addressing with Microwave Field Gradients

DTIC Science & Technology

2013-04-22

Block 13: Supplementary Note © 2013 . Published in Physical Review Letters, Vol. Ed. 0 110, (17) ( 2013 ), ( (17). DoD Components reserve a royalty...2012; published 22 April 2013 ) Individual-qubit addressing is a prerequisite for many instances of quantum information processing. We demonstrate this...to B0. We configure jBMWð0; y; 0Þj ’ 0 PRL 110, 173002 ( 2013 ) P HY S I CA L R EV I EW LE T T E R S week ending 26 APRIL 2013 0031-9007=13=110(17

Transport and spatial energy deposition of relativistic electrons in copper-doped fast ignition plasmas

DOE PAGES

Jarrott, L. C.; McGuffey, C.; Beg, F. N.; ...

2017-10-24

Fast electron transport and spatial energy deposition are investigated in integrated cone-guided Fast Ignition experiments by measuring fast electron induced copper K-shell emission using a copper tracer added to deuterated plastic shells with a geometrically reentrant gold cone. Experiments were carried out at the Laboratory for Laser Energetics on the OMEGA/OMEGA-EP Laser where the plastic shells were imploded using 54 of the 60 OMEGA60 beams (3ω, 20 kJ), while the high intensity OMEGA-EP (BL2) beam (1 ω, 10 ps, 500 J, I peak > 10 19 W/cm 2) was focused onto the inner cone tip. Here, a retrograde analysis usingmore » the hybrid-PIC electron transport code, ZUMA, is performed to examine the sensitivity of the copper Kα spatial profile on the laser-produced fast electrons, facilitating the optimization of new target point designs and laser configurations to improve the compressed core areal density by a factor of 4 and the fast electron energy coupling by a factor of 3.5.« less

CFD analysis of jet mixing in low NOx flametube combustors

NASA Technical Reports Server (NTRS)

Talpallikar, M. V.; Smith, C. E.; Lai, M. C.; Holdeman, J. D.

1991-01-01

The Rich-burn/Quick-mix/Lean-burn (RQL) combustor was identified as a potential gas turbine combustor concept to reduce NO(x) emissions in High Speed Civil Transport (HSCT) aircraft. To demonstrate reduced NO(x) levels, cylindrical flametube versions of RQL combustors are being tested at NASA Lewis Research Center. A critical technology needed for the RQL combustor is a method of quickly mixing by-pass combustion air with rich-burn gases. Jet mixing in a cylindrical quick-mix section was numerically analyzed. The quick-mix configuration was five inches in diameter and employed twelve radial-inflow slots. The numerical analyses were performed with an advanced, validated 3-D Computational Fluid Dynamics (CFD) code named REFLEQS. Parametric variation of jet-to-mainstream momentum flux ratio (J) and slot aspect ratio was investigated. Both non-reacting and reacting analyses were performed. Results showed mixing and NO(x) emissions to be highly sensitive to J and slot aspect ratio. Lowest NO(x) emissions occurred when the dilution jet penetrated to approximately mid-radius. The viability of using 3-D CFD analyses for optimizing jet mixing was demonstrated.

CFD analysis of jet mixing in low NO(x) flametube combustors

NASA Technical Reports Server (NTRS)

Talpallikar, M. V.; Smith, C. E.; Lai, M. C.; Holdeman, J. D.

1991-01-01

The Rich-burn/Quick-mix/Lean-burn (RQL) combustor has been identified as a potential gas turbine combustor concept to reduce NO(x) emissions in High Speed Civil Transport (HSCT) aircraft. To demonstrate reduced NO(x) levels, cylindrical flametube versions of RQL combustors are being tested at NASA Lewis Research Center. A critical technology needed for the RQL combustor is a method of quickly mixing by-pass combustion air with rich-burn gases. Jet mixing in a cylindrical quick-mix section was numerically analyzed. The quick-mix configuration was five inches in diameter and employed twelve radial-inflow slots. The numerical analyses were performed with an advanced, validated 3D Computational Fluid Dynamics (CFD) code named REFLEQS. Parametric variation of jet-to-mainstream momentum flux ratio (J) and slot aspect ratio was investigated. Both non-reacting and reacting analyses were performed. Results showed mixing and NO(x) emissions to be highly sensitive to J and slot aspect ratio. Lowest NO(x) emissions occurred when the dilution jet penetrated to approximately mid-radius. The viability of using 3D CFD analyses for optimizing jet mixing was demonstrated.

High Resolution Thz and FIR Spectroscopy of SOCl_2

NASA Astrophysics Data System (ADS)

Martin-Drumel, M. A.; Cuisset, A.; Sadovskii, D. A.; Mouret, G.; Hindle, F.; Pirali, O.

2013-06-01

Thionyl chloride (SOCl_2) is an extremely powerful oxidant widely used in industrial processes and playing a role in the chemistry of the atmosphere. In addition, it has a molecular configuration similar to that of phosgene (COCl_2), and is therefore of particular interest for security and defense applications. Low resolution vibrational spectra of gas phase SOCl_2 as well as high resolution pure rotational transitions up to 25 GHz have previously been investigated. To date no high resolution data are reported at frequencies higher than 25 GHz. We have investigated the THz absorption spectrum of SOCl_2 in the spectral region 70-650 GHz using a frequency multiplier chain coupled to a 1 m long single path cell containing a pressure of about 15 μbar. At the time of the writing, about 8000 pure rotational transitions of SO^{35}Cl_2 with highest J and K_a values of 110 and 50 respectively have been assigned on the spectrum. We have also recorded the high resolution FIR spectra of SOCl_2 in the spectral range 50-700 wn using synchrotron radiation at the AILES beamline of SOLEIL facility. A White-type cell aligned with an absorption path length of 150 m has been used to record, at a resolution of 0.001 wn, two spectra at pressures of 5 and 56 μbar of SOCl_2. On these spectra all FIR modes of SOCl_2 are observed (ν_2 to ν_6) and present a resolved rotational structure. Their analysis is in progress. T. J. Johnson et al., J. Phys. Chem. A 107, 6183 (2003) D. E. Martz and R. T. Lagemann, J. Chem. Phys. 22,1193 (1954) H. S. P. Müller and M. C. L. Gerry, J. Chem. Soc. Faraday Trans. 90, 3473 (1994)

Improvements to information management systems simulator

NASA Technical Reports Server (NTRS)

Bilek, R. W.

1972-01-01

The performance of personnel in the augmentation and improvement of the interactive IMSIM information management simulation model is summarized. With this augmented model, NASA now has even greater capabilities for the simulation of computer system configurations, data processing loads imposed on these configurations, and executive software to control system operations. Through these simulations, NASA has an extremely cost effective capability for the design and analysis of computer-based data management systems.

Synchronous meteorological satellite system description document, volume 3

NASA Technical Reports Server (NTRS)

Pipkin, F. B.

1971-01-01

The structural design, analysis, and mechanical integration of the synchronous meteorological satellite system are presented. The subjects discussed are: (1) spacecraft configuration, (2) structural design, (3) static load tests, (4) fixed base sinusoidal vibration survey, (5) flight configuration sinusoidal vibration tests, (6) spacecraft acoustic test, and (7) separation and shock test. Descriptions of the auxiliary propulsion subsystem, the apogee boost motor, communications system, and thermal control subsystem are included.

Finite element based stability-constrained weight minimization of sandwich composite ducts for airship applications

NASA Astrophysics Data System (ADS)

Khode, Urmi B.

High Altitude Long Endurance (HALE) airships are platform of interest due to their persistent observation and persistent communication capabilities. A novel HALE airship design configuration incorporates a composite sandwich propulsive hull duct between the front and the back of the hull for significant drag reduction via blown wake effects. The sandwich composite shell duct is subjected to hull pressure on its outer walls and flow suction on its inner walls which result in in-plane wall compressive stress, which may cause duct buckling. An approach based upon finite element stability analysis combined with a ply layup and foam thickness determination weight minimization search algorithm is utilized. Its goal is to achieve an optimized solution for the configuration of the sandwich composite as a solution to a constrained minimum weight design problem, for which the shell duct remains stable with a prescribed margin of safety under prescribed loading. The stability analysis methodology is first verified by comparing published analytical results for a number of simple cylindrical shell configurations with FEM counterpart solutions obtained using the commercially available code ABAQUS. Results show that the approach is effective in identifying minimum weight composite duct configurations for a number of representative combinations of duct geometry, composite material and foam properties, and propulsive duct applied pressure loading.

Initial Piloted Simulation Evaluation of the Reference-H High-Speed Civil Transport Design During Takeoff and Recovery From Limit Flight Conditions

NASA Technical Reports Server (NTRS)

Glaab, Louis J.

1999-01-01

An initial assessment of a proposed High-Speed Civil Transport (HSCT) was conducted in the fall of 1995 at the NASA Langley Research Center. This configuration, known as the Industry Reference-H (Ref.-H), was designed by the Boeing Aircraft Company as part of their work in the High Speed Research program. It included a conventional tail, a cranked-arrow wing, four mixed-flow turbofan engines, and capacity for transporting approximately 300 passengers. The purpose of this assessment was to evaluate and quantify operational aspects of the Reference-H configuration from a pilot's perspective with the additional goal of identifying design strengths as well as any potential configuration deficiencies. This study was aimed at evaluating the Ref.-H configuration at many points of the aircraft's envelope to determine the suitability of the vehicle to accomplish typical mission profiles as well as emergency or envelope-limit conditions. Pilot-provided Cooper-Harper ratings and comments constituted the primary vehicle evaluation metric. The analysis included simulated real-time piloted evaluations, performed in a 6 degree of freedom motion base NASA Langley Visual-Motion Simulator, combined with extensive bath analysis. The assessment was performed using the third major release of the simulation data base (known as Ref.-H cycle 2B).

Analysis and Simulation of Far-Field Seismic Data from the Source Physics Experiment

DTIC Science & Technology

2012-09-01

ANALYSIS AND SIMULATION OF FAR-FIELD SEISMIC DATA FROM THE SOURCE PHYSICS EXPERIMENT Arben Pitarka, Robert J. Mellors, Arthur J. Rodgers, Sean...Security Site (NNSS) provides new data for investigating the excitation and propagation of seismic waves generated by buried explosions. A particular... seismic model. The 3D seismic model includes surface topography. It is based on regional geological data, with material properties constrained by shallow

Phylogenetic analysis of Fusobacterium prausnitzii based upon the 16S rRNA gene sequence and PCR confirmation.

PubMed

Wang, R F; Cao, W W; Cerniglia, C E

1996-01-01

In order to develop a PCR method to detect Fusobacterium prausnitzii in human feces and to clarify the phylogenetic position of this species, its 16S rRNA gene sequence was determined. The sequence described in this paper is different from the 16S rRNA gene sequence is specific for F. prausnitzii, and the results of this assay confirmed that F. prausnitzii is the most common species in human feces. However, a PCR assay based on the original GenBank sequence was negative when it was performed with two strains of F. prausnitzii obtained from the American Type Culture Collection. A phylogenetic tree based on the new 16S rRNA gene sequence was constructed. On this tree F. prausnitzii was not a member of the Fusobacterium group but was closer to some Eubacterium spp. and located between Clostridium "clusters III and IV" (M.D. Collins, P.A. Lawson, A. Willems, J.J. Cordoba, J. Fernandez-Garayzabal, P. Garcia, J. Cai, H. Hippe, and J.A.E. Farrow, Int. J. Syst. Bacteriol. 44:812-826, 1994).

EDITORIAL: The FDR Prize The FDR Prize

NASA Astrophysics Data System (ADS)

Funakoshi, Mitsuaki

2011-08-01

From the 56 papers published in 2010 in Fluid Dynamics Research the following paper has been selected for the fourth FDR prize: 'Baroclinic multipole formation from heton interaction' by M A Sokolovskiy and X J Carton, published in volume 42 (August 2010) 045501. Coherent vortices are a universal feature of fluids at moderate and large Reynolds number, and have particular relevance to the quasi-two-dimensional flows used to model phenomena in the atmosphere and ocean. The structure and interaction of such vortices have proved a fascinating area for the researchers of fluid dynamics, including thoreticians, observers and experimentalists, together with related problems of how they mix fluids and how they transport scalars such as temperature and salinity. In this paper 'hetons' are considered; they are vortices of dipolar structures in a multilayer rotating fluid, carry thermal anomalies, and are relevant to transport in flows such as the Gulf Stream. The paper is a comprehensive study of the structure, invariants and interactions of two opposite-signed hetons in a two-layer fluid for several initial configurations and for several values of the Rossby radius of deformation, using models based on point vortex dynamics and contour dynamics of finite-area vortex regions. Different types of coupling and interactions are isolated and discussed. Depending on the initial configuration and the value of the radius of deformation, the time evolutions toward horizonal dipoles, vertically tilted dipoles, L-shaped dipoles, and Z-shaped tripoles are observed in the case of finite-area vortices. Using point vortex dynamics a rigorous analysis based on trilinear coordinates is performed, and the appearance of similar structures is shown analytically, except for the L-shaped dipoles. The contribution of this paper to the important problem of heton interaction is both profound and substantial. The study will be of great interest to a wide variety of readers and is likely to inspire further numerical and experimental work, as well being helpful in the interpretation and analysis of observations. Overall, the paper will undoubtedly have a large impact on the fluid dynamics community.

An Automated System for Comprehensive Assessment of Visual Field Sensitivity.

DTIC Science & Technology

1985-04-01

act to degrade this basic configuration; e.g., pathology, such as glaucoma and retinitis pigmentosa ; environmental extremes, such as hypoxia...and B. Appleton. 1971. Effects of hypoxia on visual performance and retinal vascular state. Journal of Applied Physiology. 31: 357蘺. Kobrick, J. L

A comparison of single-cycle versus multiple-cycle proof testing strategies

NASA Technical Reports Server (NTRS)

Hudak, S. J., Jr.; Mcclung, R. C.; Bartlett, M. L.; Fitzgerald, J. H.; Russell, D. A.

1990-01-01

An evaluation of single-cycle and multiple-cycle proof testing (MCPT) strategies for SSME components is described. Data for initial sizes and shapes of actual SSME hardware defects are analyzed statistically. Closed-form estimates of the J-integral for surface flaws are derived with a modified reference stress method. The results of load- and displacement-controlled stable crack growth tests on thin IN-718 plates with deep surface flaws are summarized. A J-resistance curve for the surface-cracked configuration is developed and compared with data from thick compact tension specimens. The potential for further crack growth during large unload/reload cycles is discussed, highlighting conflicting data in the literature. A simple model for ductile crack growth during MCPT based on the J-resistance curve is used to study the potential effects of key variables. The projected changes in the crack size distribution during MCPT depend on the interactions between several key parameters, including the number of proof cycles, the nature of the resistance curve, the initial crack size distribution, the component boundary conditions (load vs. displacement control), and the magnitude of the applied load or displacement. The relative advantages of single-cycle and multiple-cycle proof testing appear to be specific, therefore, to individual component geometry, material, and loading.

Ultralow power artificial synapses using nanotextured magnetic Josephson junctions.

PubMed

Schneider, Michael L; Donnelly, Christine A; Russek, Stephen E; Baek, Burm; Pufall, Matthew R; Hopkins, Peter F; Dresselhaus, Paul D; Benz, Samuel P; Rippard, William H

2018-01-01

Neuromorphic computing promises to markedly improve the efficiency of certain computational tasks, such as perception and decision-making. Although software and specialized hardware implementations of neural networks have made tremendous accomplishments, both implementations are still many orders of magnitude less energy efficient than the human brain. We demonstrate a new form of artificial synapse based on dynamically reconfigurable superconducting Josephson junctions with magnetic nanoclusters in the barrier. The spiking energy per pulse varies with the magnetic configuration, but in our demonstration devices, the spiking energy is always less than 1 aJ. This compares very favorably with the roughly 10 fJ per synaptic event in the human brain. Each artificial synapse is composed of a Si barrier containing Mn nanoclusters with superconducting Nb electrodes. The critical current of each synapse junction, which is analogous to the synaptic weight, can be tuned using input voltage spikes that change the spin alignment of Mn nanoclusters. We demonstrate synaptic weight training with electrical pulses as small as 3 aJ. Further, the Josephson plasma frequencies of the devices, which determine the dynamical time scales, all exceed 100 GHz. These new artificial synapses provide a significant step toward a neuromorphic platform that is faster, more energy-efficient, and thus can attain far greater complexity than has been demonstrated with other technologies.

Ultralow power artificial synapses using nanotextured magnetic Josephson junctions

PubMed Central

Schneider, Michael L.; Donnelly, Christine A.; Russek, Stephen E.; Baek, Burm; Pufall, Matthew R.; Hopkins, Peter F.; Dresselhaus, Paul D.; Benz, Samuel P.; Rippard, William H.

2018-01-01

Neuromorphic computing promises to markedly improve the efficiency of certain computational tasks, such as perception and decision-making. Although software and specialized hardware implementations of neural networks have made tremendous accomplishments, both implementations are still many orders of magnitude less energy efficient than the human brain. We demonstrate a new form of artificial synapse based on dynamically reconfigurable superconducting Josephson junctions with magnetic nanoclusters in the barrier. The spiking energy per pulse varies with the magnetic configuration, but in our demonstration devices, the spiking energy is always less than 1 aJ. This compares very favorably with the roughly 10 fJ per synaptic event in the human brain. Each artificial synapse is composed of a Si barrier containing Mn nanoclusters with superconducting Nb electrodes. The critical current of each synapse junction, which is analogous to the synaptic weight, can be tuned using input voltage spikes that change the spin alignment of Mn nanoclusters. We demonstrate synaptic weight training with electrical pulses as small as 3 aJ. Further, the Josephson plasma frequencies of the devices, which determine the dynamical time scales, all exceed 100 GHz. These new artificial synapses provide a significant step toward a neuromorphic platform that is faster, more energy-efficient, and thus can attain far greater complexity than has been demonstrated with other technologies. PMID:29387787

Neo-clerodane and abietane diterpenoids with neurotrophic activities from the aerial parts of Salvia leucantha Cav.

PubMed

Li, Lai-Wei; Qi, Yan-Yan; Liu, Shi-Xi; Wu, Xing-De; Zhao, Qin-Shi

2018-04-04

Four new neoclerodane diterpenoids, leucansalvialins FI (1-4), and one rare 18(4 → 3)-abeo-abietane diterpenoid, leucansalvialin J (5), were isolated from the aerial part of Salvia leucantha Cav., along with 14 known analogues. Leucansalvialin F (1) represents the first rearranged salvigenane type clerodane-17,12:18,6-diolide. Their structures were elucidated by 1D and 2D NMR spectroscopic data analysis, and the absolute configurations of 1, 2, 3, and 5 were determinded by X-ray diffraction crystal analysis and the ECD technique. All of the isolated components were evaluated for their neurotrophic activities on PC12 cells and all new compounds were evaluated for their cytotoxicity against five human cancer cell lines (HL-60, A-549, SMMC-7721, MCF-7, and SW480). Compounds 2 and 5 showed moderate neuroprotective effects in an in vitro assay. Copyright © 2018. Published by Elsevier B.V.

Assessment of multireference approaches to explicitly correlated full configuration interaction quantum Monte Carlo

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kersten, J. A. F., E-mail: jennifer.kersten@cantab.net; Alavi, Ali, E-mail: a.alavi@fkf.mpg.de; Max Planck Institute for Solid State Research, Heisenbergstraße 1, 70569 Stuttgart

2016-08-07

The Full Configuration Interaction Quantum Monte Carlo (FCIQMC) method has proved able to provide near-exact solutions to the electronic Schrödinger equation within a finite orbital basis set, without relying on an expansion about a reference state. However, a drawback to the approach is that being based on an expansion of Slater determinants, the FCIQMC method suffers from a basis set incompleteness error that decays very slowly with the size of the employed single particle basis. The FCIQMC results obtained in a small basis set can be improved significantly with explicitly correlated techniques. Here, we present a study that assesses andmore » compares two contrasting “universal” explicitly correlated approaches that fit into the FCIQMC framework: the [2]{sub R12} method of Kong and Valeev [J. Chem. Phys. 135, 214105 (2011)] and the explicitly correlated canonical transcorrelation approach of Yanai and Shiozaki [J. Chem. Phys. 136, 084107 (2012)]. The former is an a posteriori internally contracted perturbative approach, while the latter transforms the Hamiltonian prior to the FCIQMC simulation. These comparisons are made across the 55 molecules of the G1 standard set. We found that both methods consistently reduce the basis set incompleteness, for accurate atomization energies in small basis sets, reducing the error from 28 mE{sub h} to 3-4 mE{sub h}. While many of the conclusions hold in general for any combination of multireference approaches with these methodologies, we also consider FCIQMC-specific advantages of each approach.« less

Aerodynamic preliminary analysis system. Part 2: User's manual and program description

NASA Technical Reports Server (NTRS)

Divan, P.; Dunn, K.; Kojima, J.

1978-01-01

A comprehensive aerodynamic analysis program based on linearized potential theory is described. The solution treats thickness and attitude problems at subsonic and supersonic speeds. Three dimensional configurations with or without jet flaps having multiple nonplanar surfaces of arbitrary planform and open or closed slender bodies or noncircular contour are analyzed. Longitudinal and lateral-directional static and rotary derivative solutions are generated. The analysis is implemented on a time sharing system in conjunction with an input tablet digitizer and an interactive graphics input/output display and editing terminal to maximize its responsiveness to the preliminary analysis problem. Nominal case computation time of 45 CPU seconds on the CDC 175 for a 200 panel simulation indicates the program provides an efficient analysis for systematically performing various aerodynamic configuration tradeoff and evaluation studies.

Propfan test assessment testbed aircraft flutter model test report

NASA Technical Reports Server (NTRS)

Jenness, C. M. J.

1987-01-01

The PropFan Test Assessment (PTA) program includes flight tests of a propfan power plant mounted on the left wind of a modified Gulfstream II testbed aircraft. A static balance boom is mounted on the right wing tip for lateral balance. Flutter analyses indicate that these installations reduce the wing flutter stabilizing speed and that torsional stiffening and the installation of a flutter stabilizing tip boom are required on the left wing for adequate flutter safety margins. Wind tunnel tests of a 1/9th scale high speed flutter model of the testbed aircraft were conducted. The test program included the design, fabrication, and testing of the flutter model and the correlation of the flutter test data with analysis results. Excellent correlations with the test data were achieved in posttest flutter analysis using actual model properties. It was concluded that the flutter analysis method used was capable of accurate flutter predictions for both the (symmetric) twin propfan configuration and the (unsymmetric) single propfan configuration. The flutter analysis also revealed that the differences between the tested model configurations and the current aircraft design caused the (scaled) model flutter speed to be significantly higher than that of the aircraft, at least for the single propfan configuration without a flutter boom. Verification of the aircraft final design should, therefore, be based on flutter predictions made with the test validated analysis methods.

Determination of Reaction Stoichiometries by Flow Injection Analysis.

ERIC Educational Resources Information Center

Rios, Angel; And Others

1986-01-01

Describes a method of flow injection analysis intended for calculation of complex-formation and redox reaction stoichiometries based on a closed-loop configuration. The technique is suitable for use in undergraduate laboratories. Information is provided for equipment, materials, procedures, and sample results. (JM)

Development of an Automated Micro-Computer Knowledge-Based Integrated Configuration Management System for the Stock Point Logistics Integrated Communications Environment (SPLICE) Project Management Staff.

DTIC Science & Technology

1986-03-01

Installation Cost Real Basic Monthly Maintenance Cost Real -" . I 2 ! UU LU uj ~~ LA . ~z LU J LLU 151 APPENDIX B: MAINTENANCE MANUAL Page 15 -LJ uLA- u’Il -LJ...bl 59748.0 9 09 NARDAC JACKSONVILLE, FL, 2 2 VIII A S 188471.0 10 10 NARDAC NEW ORLEANS, LA 2 2 P A S 73918.0 11 11 NARDAC NORFOLK, VA 2 2 VIII A S...1366 Beqin 1367 FOR Row =0 to 5 LWJ 1368 FOR Col 1 to 3 DO 1369 Beqin 1370 Subtotals [Row, Coll := 0; 1371 IF Col ( 3 TIEN Totals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Do, Hainam, E-mail: h.do@nottingham.ac.uk, E-mail: richard.wheatley@nottingham.ac.uk; Wheatley, Richard J., E-mail: h.do@nottingham.ac.uk, E-mail: richard.wheatley@nottingham.ac.uk

A robust and model free Monte Carlo simulation method is proposed to address the challenge in computing the classical density of states and partition function of solids. Starting from the minimum configurational energy, the algorithm partitions the entire energy range in the increasing energy direction (“upward”) into subdivisions whose integrated density of states is known. When combined with the density of states computed from the “downward” energy partitioning approach [H. Do, J. D. Hirst, and R. J. Wheatley, J. Chem. Phys. 135, 174105 (2011)], the equilibrium thermodynamic properties can be evaluated at any temperature and in any phase. The methodmore » is illustrated in the context of the Lennard-Jones system and can readily be extended to other molecular systems and clusters for which the structures are known.« less

Heat capacities and thermodynamic properties of annite (aluminous iron biotite)

USGS Publications Warehouse

Hemingway, B.S.; Robie, R.A.

1990-01-01

The heat capacities have been measured between 7 and 650 K by quasi-adiabatic calorimetry and differential scanning calorimetry. At 298.15 K and 1 bar, the calorimetric entropy for our sample is 354.9??0.7 J/(mol.K). A minimum configurational entropy of 18.7 J/(mol.K) for full disorder of Al/Si in the tetrahedral sites should be added to the calorimetric entropy for third-law calculations. The heat capacity equation [Cp in units of J/mol.K)] Cp0 = 583.586 + 0.075246T - 3420.60T-0.5 - (4.4551 ?? 106)T-2 fits the experimental and estimated heat capacities for our sample (valid range 250 to 1000 K) with an average deviation of 0.37%. -from Authors

Investigation of Modularly Configured Attached Processors with Intelligent Memories

DTIC Science & Technology

1994-09-30

sequence of computations becomes cl = c11 + C[i, i] := Cli, j] + A[i, k) * Blk, j]; al x bti, c12 - c12 + k X bkX2, C13 = C1 3 + alk X b 3 , ... , c =n...Cin + alk X bkn, C2 1 = Cat + a2k x bkl , The sequence of computations becomes cii = a I x bli, C22 = cU2 + a2k x b2, ... Cj a2 1x bij, ca3j = aa x...1 to 1/2 Least significant 1/2 address bits Fig. 1. Block diagram of a memory module PREGVJKE is v I pis P16 16 ItO16 = 4-81T OECD - = AMKSS A s-Byrf

Electron impact ionization from p-orbital targets

NASA Astrophysics Data System (ADS)

Saha, Bidhan; Basak, Arun K.; Alfaz Uddin, M.

2006-05-01

Electron impact ionization cross sections are evaluated using a modified version [1] of the BELL formula [2] for a wide range of isoelectronic targets, ranging from Li to Ne targets with both the open and closed shell configurations. In this report the MBELL parameters are generalized for treating the orbital quantum numbers nl dependency; its accuracy has been tested by evaluating cross sections for a wider range of species and energies. Details will be presented at the meeting. [1] A. K. F. Haque, M. A. Uddin, A. K. Basak, K. R. Karim and B. C. Saha, Phys. Rev. A73, 012708 (2005). [2] K. L. Bell, H. B. Gilbody, J. G. Hughes, A. E. Kingston, and F. J. Smith, J. Phys. Chem. Ref. Data 12, 891 (1983).

One joule output from a diode-array-pumped Nd:YAG laser with side-pumped rod geometry

NASA Technical Reports Server (NTRS)

Kasinski, Jeffrey J.; Hughes, Will; Dibiase, Don; Bournes, Patrick; Burnham, Ralph

1992-01-01

Output of 1.25 J per pulse (1.064 micron) with an absolute optical efficiency of 28 percent and corresponding electrical efficiency of 10 percent was demonstrated in a diode-array-pumped Nd:YAG laser using a side-pumped rod geometry in a master-oscillator/power-amplifier configuration. In Q-switched operation, an output of 0.75 J in a 17-ns pulse was obtained. The fundamental laser output was frequency doubled in KTP with 60 percent conversion efficiency to obtain 0.45 J in a 16-ns pulse at 532 nm. The output beam had high spatial quality with pointing stability better than 40 microrad and a shot-to-shot pulse energy fluctuation of less than +/-3 percent.

Quantitative assessment of energy and resource recovery in wastewater treatment plants based on plant-wide simulations.

PubMed

Fernández-Arévalo, T; Lizarralde, I; Fdz-Polanco, F; Pérez-Elvira, S I; Garrido, J M; Puig, S; Poch, M; Grau, P; Ayesa, E

2017-07-01

The growing development of technologies and processes for resource treatment and recovery is offering endless possibilities for creating new plant-wide configurations or modifying existing ones. However, the configurations' complexity, the interrelation between technologies and the influent characteristics turn decision-making into a complex or unobvious process. In this frame, the Plant-Wide Modelling (PWM) library presented in this paper allows a thorough, comprehensive and refined analysis of different plant configurations that are basic aspects in decision-making from an energy and resource recovery perspective. In order to demonstrate the potential of the library and the need to run simulation analyses, this paper carries out a comparative analysis of WWTPs, from a techno-economic point of view. The selected layouts were (1) a conventional WWTP based on a modified version of the Benchmark Simulation Model No. 2, (2) an upgraded or retrofitted WWTP, and (3) a new Wastewater Resource Recovery Facilities (WRRF) concept denominated as C/N/P decoupling WWTP. The study was based on a preliminary analysis of the organic matter and nutrient energy use and recovery options, a comprehensive mass and energy flux distribution analysis in each configuration in order to compare and identify areas for improvement, and a cost analysis of each plant for different influent COD/TN/TP ratios. Analysing the plants from a standpoint of resources and energy utilization, a low utilization of the energy content of the components could be observed in all configurations. In the conventional plant, the COD used to produce biogas was around 29%, the upgraded plant was around 36%, and 34% in the C/N/P decoupling WWTP. With regard to the self-sufficiency of plants, achieving self-sufficiency was not possible in the conventional plant, in the upgraded plant it depended on the influent C/N ratio, and in the C/N/P decoupling WWTP layout self-sufficiency was feasible for almost all influents, especially at high COD concentrations. The plant layouts proposed in this paper are just a sample of the possibilities offered by current technologies. Even so, the library presented here is generic and can be used to construct any other plant layout, provided that a model is available. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of Prediction Techniques for Aerodynamic Loads Acting on External Stores

DTIC Science & Technology

1975-11-01

Unclassified Se’cunty Classaficataon DOCUMENT CONTROL DATA- R &D Streurtet, ci., ,flcf.,t, oh’ till, t ol of , hst, , I .i- 4ttt*ic., ,n la t t I hi tr...4 N 𔃺 0 I 0. o 0 00 0 0 4J 0 0 0 0 .o- o .8. 0 0 .-8 o Sn 140SnS 0 o 0 0 00 La , 0 0 .8 0 4 L 0 l Ř - 0 Sn n Sn2 9kn I Sn Sn 0Sn 𔃺 2 Sn.m...weighted regression analysis E- udy of configurations in this category. 4.5 Stngle Weapon Plus Rack As was explained in Section 4.2 for arrangements

Large scale EMF in current sheets induced by tearing modes

NASA Astrophysics Data System (ADS)

Mizerski, Krzysztof A.

2018-02-01

An extension of the analysis of resistive instabilities of a sheet pinch from a famous work by Furth et al (1963 Phys. Fluids 6 459) is presented here, to study the mean electromotive force (EMF) generated by the developing instability. In a Cartesian configuration and in the presence of a current sheet first the boundary layer technique is used to obtain global, matched asymptotic solutions for the velocity and magnetic field and then the solutions are used to calculate the large-scale EMF in the system. It is reported, that in the bulk the curl of the mean EMF is linear in {{j}}0\\cdot {{B}}0, a simple pseudo-scalar quantity constructed from the large-scale quantities.

GPS baseline configuration design based on robustness analysis

NASA Astrophysics Data System (ADS)

Yetkin, M.; Berber, M.

2012-11-01

The robustness analysis results obtained from a Global Positioning System (GPS) network are dramatically influenced by the configurationof the observed baselines. The selection of optimal GPS baselines may allow for a cost effective survey campaign and a sufficiently robustnetwork. Furthermore, using the approach described in this paper, the required number of sessions, the baselines to be observed, and thesignificance levels for statistical testing and robustness analysis can be determined even before the GPS campaign starts. In this study, wepropose a robustness criterion for the optimal design of geodetic networks, and present a very simple and efficient algorithm based on thiscriterion for the selection of optimal GPS baselines. We also show the relationship between the number of sessions and the non-centralityparameter. Finally, a numerical example is given to verify the efficacy of the proposed approach.

Design and Implementation of a Numerical Technique to Inform Anisotropic Hyperelastic Finite Element Models using Diffusion-Weighted Imaging

DTIC Science & Technology

2011-10-01

the deviatoric part of a tensor in the reference configuration and p = −∂Ψ ∂J is the hydrostatic pressure. Using the chain 4 rule, equation 13 can be...Kirchoff stress tensor S to the current configuration, and a scaling with the inverse of the volume ratio, transforms equation 16 to the Cauchy stress ...a characteristic of most soft tissues. Then, similar to equation 13, the second Piola-Kirchoff stress is given by: S = 2J−2/3DEV [ ∂Ψisoc ( C ) ∂C

Determination of optimum mounting configurations for flat-plate photovoltaic modules based on a structured field experiment and simulated results from PVFORM, a photovoltaic system performance model

NASA Astrophysics Data System (ADS)

Menicucci, D. F.

1986-01-01

The performance of a photovoltaic (PV) system is affected by its mounting configuration. The optimal configuration is unclear because of lack of experience and data. Sandia National Laboratories, Albuquerque (SNLA), has conducted a controlled field experiment to compare four types of the most common module mounting. The data from the experiment were used to verify the accuracy of PVFORM, a new computer program that simulates PV performance. PVFORM was then used to simulate the performance of identical PV modules on different mounting configurations at 10 sites throughout the US. This report describes the module mounting configurations, the experimental methods used, the specialized statistical techniques used in the analysis, and the final results of the effort. The module mounting configurations are rank ordered at each site according to their annual and seasonal energy production performance, and each is briefly discussed in terms of its advantages and disadvantages in various applications.

Decoupling analysis of a novel bearingless flux-switching permanent magnet motor

NASA Astrophysics Data System (ADS)

Zhao, Chenyin; Zhu, Huangqiu; Qin, Yuemei

2017-05-01

In this paper, a novel 12/10 stator/rotor pole bearingless flux-switching permanent magnet (BFSPM) motor is proposed to overcome the drawbacks of rotor permanent magnet type bearingless motors. The basic motor configuration, including motor configuration and winding configuration, is introduced firstly. Then, based on the principle of reverse direction magnetization for symmetrical rotor teeth, the radial suspension forces generation principle is analyzed in detail. Finally, decoupling performances between suspension force windings and torque windings are investigated. The results show that the proposed BFSPM not only ensures the merits of high torque output capability compared with conventional 12/10 stator/rotor pole FSPM motor, but also achieves stable radial suspension forces which have little mutual effect with torque. The validity of the proposed structure has been verified by finite element analysis (FEA).

Solar U- and J- Bursts at the Frequencies 10-30MHz

NASA Astrophysics Data System (ADS)

Dorovskyy, V. V.; Melnik, V. N.; Konovalenko, A. A.; Abranin, E. P.; Rucker, H. O.; Lecacheux, A.

2006-08-01

In the present report we discuss the results of observations of solar U- and J- bursts over the frequency range 10-30MHz, which have been obtained within the framework of an international observational campaign in June - August, 2004 at the radio telescope UTR-2 (Kharkov, Ukraine). We succeed to observe these types of bursts for the first time at such a low frequencies due to combination of large effective area of the radio telescope and high sensitivity of the new back-end. During June - August, 2004 about 30 U- and J- bursts were registered, and only 5 of them were confidently identified as U-bursts that may speak about the relative sparsity of the latter at mentioned frequencies. Both the isolated bursts and their sequences were observed. On average the turning frequencies lay in the range 10-22 MHz that corresponds to the arches heliocentric heights of 1.6-2.2 solar radii. In some sequences the bursts turning frequency was stable that may indicate the arch stability, while in others the turning frequency had tendency to vary from burst to burst. Durations of U- and J- bursts did not differ from those of usual Type III bursts (3-7s), while the drift rates of an ascending arm (on the average -1MHz/ s) was a little bit lower, than those of ordinary Type III bursts in this range. The harmonic structure of U- and J- bursts, and also Jb-J pairs (analogous to IIIb-III pairs) were registered. Also L-shaped bursts (Leblanc and Hoyos, 1985) were recorded. A specific feature of L-shaped bursts is prolonged zero-drift region on their dynamic spectra. The sizes and configurations of the arches were estimated on the base of obtained data. Possible explanations of the observed properties of U- and J- bursts are discussed.

VizieR Online Data Catalog: GLASS. IX. Structural param. from HFF & GLASS (Morishita+, 2017)

NASA Astrophysics Data System (ADS)

Morishita, T.; Abramson, L. E.; Treu, T.; Vulcani, B.; Schmidt, K. B.; Dressler, A.; Poggianti, B. M.; Malkan, M. A.; Wang, X.; Huang, K.-H.; Trenti, M.; Bradac, M.; Hoag, A.

2017-09-01

We base our analysis on Hubble Frontier Fields (HFF; Lotz+ 2017ApJ...837...97L) imaging and Grism Survey from Space (GLASS; Schmidt+ 2014ApJ...782L..36S; Treu+, 2015, J/ApJ/812/114) HST spectroscopy for the first four HFF clusters with complete data: Abell2744 (z=0.308), MACS0416 (0.396), MACS0717 (0.548), and MACS1149 (0.544). HFF imaging spans ACS F435/606/814W through WFC3IR F105/125/140/160W filters (seven bands). Our final catalog consists of 3948 galaxies, with 2200 in clusters and 1748 in field environments. A total of 298 have ground-based and 168 have GLASS spectroscopic redshifts. (1 data file).

jSPyDB, an open source database-independent tool for data management

NASA Astrophysics Data System (ADS)

Pierro, Giuseppe Antonio; Cavallari, Francesca; Di Guida, Salvatore; Innocente, Vincenzo

2011-12-01

Nowadays, the number of commercial tools available for accessing Databases, built on Java or .Net, is increasing. However, many of these applications have several drawbacks: usually they are not open-source, they provide interfaces only with a specific kind of database, they are platform-dependent and very CPU and memory consuming. jSPyDB is a free web-based tool written using Python and Javascript. It relies on jQuery and python libraries, and is intended to provide a simple handler to different database technologies inside a local web browser. Such a tool, exploiting fast access libraries such as SQLAlchemy, is easy to install, and to configure. The design of this tool envisages three layers. The front-end client side in the local web browser communicates with a backend server. Only the server is able to connect to the different databases for the purposes of performing data definition and manipulation. The server makes the data available to the client, so that the user can display and handle them safely. Moreover, thanks to jQuery libraries, this tool supports export of data in different formats, such as XML and JSON. Finally, by using a set of pre-defined functions, users are allowed to create their customized views for a better data visualization. In this way, we optimize the performance of database servers by avoiding short connections and concurrent sessions. In addition, security is enforced since we do not provide users the possibility to directly execute any SQL statement.

An analysis of satellite state vector observability using SST tracking data

NASA Technical Reports Server (NTRS)

Englar, T. S., Jr.; Hammond, C. L.

1976-01-01

Observability of satellite state vectors, using only SST tracking data was investigated by covariance analysis under a variety of satellite and station configurations. These results indicate very precarious observability in most short arc cases. The consequences of this are large variances on many state components, such as the downrange component of the relay satellite position. To illustrate the impact of observability problems, an example is given of two distinct satellite orbit pairs generating essentially the same data arc. The physical bases for unobservability are outlined and related to proposed TDRSS configurations. Results are relevant to any mission depending upon TDRSS to determine satellite state. The required mathematical analysis and the software used is described.

Self-Configuration and Self-Optimization Process in Heterogeneous Wireless Networks

PubMed Central

Guardalben, Lucas; Villalba, Luis Javier García; Buiati, Fábio; Sobral, João Bosco Mangueira; Camponogara, Eduardo

2011-01-01

Self-organization in Wireless Mesh Networks (WMN) is an emergent research area, which is becoming important due to the increasing number of nodes in a network. Consequently, the manual configuration of nodes is either impossible or highly costly. So it is desirable for the nodes to be able to configure themselves. In this paper, we propose an alternative architecture for self-organization of WMN based on Optimized Link State Routing Protocol (OLSR) and the ad hoc on demand distance vector (AODV) routing protocols as well as using the technology of software agents. We argue that the proposed self-optimization and self-configuration modules increase the throughput of network, reduces delay transmission and network load, decreases the traffic of HELLO messages according to network’s scalability. By simulation analysis, we conclude that the self-optimization and self-configuration mechanisms can significantly improve the performance of OLSR and AODV protocols in comparison to the baseline protocols analyzed. PMID:22346584

Self-configuration and self-optimization process in heterogeneous wireless networks.

PubMed

Guardalben, Lucas; Villalba, Luis Javier García; Buiati, Fábio; Sobral, João Bosco Mangueira; Camponogara, Eduardo

2011-01-01

Self-organization in Wireless Mesh Networks (WMN) is an emergent research area, which is becoming important due to the increasing number of nodes in a network. Consequently, the manual configuration of nodes is either impossible or highly costly. So it is desirable for the nodes to be able to configure themselves. In this paper, we propose an alternative architecture for self-organization of WMN based on Optimized Link State Routing Protocol (OLSR) and the ad hoc on demand distance vector (AODV) routing protocols as well as using the technology of software agents. We argue that the proposed self-optimization and self-configuration modules increase the throughput of network, reduces delay transmission and network load, decreases the traffic of HELLO messages according to network's scalability. By simulation analysis, we conclude that the self-optimization and self-configuration mechanisms can significantly improve the performance of OLSR and AODV protocols in comparison to the baseline protocols analyzed.

PSHFT - COMPUTERIZED LIFE AND RELIABILITY MODELLING FOR TURBOPROP TRANSMISSIONS

NASA Technical Reports Server (NTRS)

Savage, M.

1994-01-01

The computer program PSHFT calculates the life of a variety of aircraft transmissions. A generalized life and reliability model is presented for turboprop and parallel shaft geared prop-fan aircraft transmissions. The transmission life and reliability model is a combination of the individual reliability models for all the bearings and gears in the main load paths. The bearing and gear reliability models are based on the statistical two parameter Weibull failure distribution method and classical fatigue theories. The computer program developed to calculate the transmission model is modular. In its present form, the program can analyze five different transmissions arrangements. Moreover, the program can be easily modified to include additional transmission arrangements. PSHFT uses the properties of a common block two-dimensional array to separate the component and transmission property values from the analysis subroutines. The rows correspond to specific components with the first row containing the values for the entire transmission. Columns contain the values for specific properties. Since the subroutines (which determine the transmission life and dynamic capacity) interface solely with this property array, they are separated from any specific transmission configuration. The system analysis subroutines work in an identical manner for all transmission configurations considered. Thus, other configurations can be added to the program by simply adding component property determination subroutines. PSHFT consists of a main program, a series of configuration specific subroutines, generic component property analysis subroutines, systems analysis subroutines, and a common block. The main program selects the routines to be used in the analysis and sequences their operation. The series of configuration specific subroutines input the configuration data, perform the component force and life analyses (with the help of the generic component property analysis subroutines), fill the property array, call up the system analysis routines, and finally print out the analysis results for the system and components. PSHFT is written in FORTRAN 77 and compiled on a MicroSoft FORTRAN compiler. The program will run on an IBM PC AT compatible with at least 104k bytes of memory. The program was developed in 1988.

The J3 SCR model applied to resonant converter simulation

NASA Technical Reports Server (NTRS)

Avant, R. L.; Lee, F. C. Y.

1985-01-01

The J3 SCR model is a continuous topology computer model for the SCR. Its circuit analog and parameter estimation procedure are uniformly applicable to popular computer-aided design and analysis programs such as SPICE2 and SCEPTRE. The circuit analog is based on the intrinsic three pn junction structure of the SCR. The parameter estimation procedure requires only manufacturer's specification sheet quantities as a data base.

Aerodynamic design and analysis of the AST-204, AST-205, and AST-206 blended wing-fuse large supersonic transport configuration concepts

NASA Technical Reports Server (NTRS)

Martin, G. L.; Walkley, K. B.

1980-01-01

The aerodynamic design and analysis of three blended wing-fuselage supersonic cruise configurations providing four, five, and six abreast seating was conducted using a previously designed supersonic cruise configuration as the baseline. The five abreast configuration was optimized for wave drag at a Mach number of 2.7. The four and six abreast configurations were also optimized at Mach 2.7, but with the added constraint that the majority of their structure be common with the five abreast configuration. Analysis of the three configurations indicated an improvement of 6.0, 7.5, and 7.7 percent in cruise lift-to-drag ratio over the baseline configuration for the four, five, and six abreast configurations, respectively.

Magnetic field of jupiter and its interaction with the solar wind.

PubMed

Smith, E J; Davis, L; Jones, D E; Colburn, D S; Coleman, P J; Dyal, P; Sonett, C P

1974-01-25

Jupiter's magnetic field and its interaction with the magnetized solar wind were observed with the Pioneer 10 vector helium magnetometer. The magnetic dipole is directed opposite to that of the earth with a moment of 4.0 gauss R(J)(3) (R(J), Jupiter radius), and an inclination of 15 degrees lying in a system III meridian of 230 degrees . The dipole is offset about 0.1 R(J) north of the equatorial plane and about 0.2 R(J) toward longitude 170 degrees . There is severe stretching of the planetary field parallel to the equator throughout the outer magnetosphere, accompanied by a systematic departure from meridian planes. The field configuration implies substantial plasma effects inside the magnetosphere, such as thermal pressure, centrifugal forces, and differential rotation. As at the earth, the outer boundary is thin, nor diffuse, and there is a detached bow shock.

Collisions of O+ with He at low energies

NASA Astrophysics Data System (ADS)

Joseph, Dwayne C.; Saha, B. C.; Zhao, L. B.

2009-05-01

We have investigated the following charge transfer processO^+( ^4S^0, ^2D^0, ^2P^0)+He->O( ^3P)+He^+-δE using the full quantum [1] and semi-classical molecular [2]orbital close-coupling (MOCC) approximations. The quantum MOCC equations are solved numerically in the adiabatic representation [3]. Using MRD-CI package [4] the ab initio configuration interaction calculation is carried out for potential energies. Details of our findings will be reported in the conference. [1] B. H. Bransden and M. R. C. McDowell, ``Charge Exchange and the Theory of Ion-Atom Collisions'', Clarendon Press, Oxford, 1992. [2] M. Kimura and N. F. Lane, At. Mol. Opt. Phys 26, 79 (1990). [3] J. P. Braga and J. C. Belchoir, J. Comput. Chem 17, 1559 (1996). [4] R. J. Buenker, ``Current Aspects of Quantum Chemistry 1981, Vol 21, edited by R. Carbo (Elsevier, Amsterdam), p 17.

The Spacelab J mission

NASA Technical Reports Server (NTRS)

Cremin, J. W.; Leslie, F. W.

1990-01-01

This paper describes Spacelab J (SL-J), its mission characteristics, features, parameters and configuration, the unique nature of the shared reimbursable cooperative effort with the National Space Development Agency (NASDA) of Japan and the evolution, content and objectives of the mission scientific experiment complement. The mission is planned for launch in 1991. This long module mission has 35 experiments from Japan as well as 9 investigations from the United States. The SL-J payload consists of two broad scientific disciplines which require the extended microgravity or cosmic ray environment: (1) materials science such as crystal growth, solidification processes, drop dynamics, free surface flows, gas dynamics, metallurgy and semiconductor technology; and (2) life science including cell development, human physiology, radiation-induced mutations, vestibular studies, embryo development, and medical technology. Through an international agreement with NASDA, NASA is preparing to fly the first Japanese manned, scientific, cooperative endeavor with the United States.

Flight set 360T004 (STS-30)

NASA Technical Reports Server (NTRS)

Nelsen, Lowell V.

1990-01-01

The performance of 360T004, Forth Flight, Redesigned Solid Rocket Motors (RSRM) is assessed in respect to joint sealing issues as seen from post-test inspection of the seals and sealing surfaces. The factory joint disassembly inspections for this flight set were omitted. The decision was based on the rational that there is sufficient information in the present data base, and this would give H-7 refurbishment operations faster turn around time for this set of hardware. The factory joint disassembly inspections will resume for 360H005, Fifth Flight, through 360L007, Seventh Flight, due to a new grease application being in effect during the assembly process. The left hand nozzle was forced into the snubbed position upon splash down. This required unique tooling to be manufactured to perform the disassembly of the internal nozzle joints. This was completed on February 5 and 6, 1990 at the H-5 Clearfield, Utah facility. The RSRM consisting of capture feature, field joints with the J-joint insulation configuration is illustrated. The nozzle-to-case joint design, which includes 100, 7/8-inch radial bolts in conjunction with a wiper O-ring and modified insulation design is also illustrated, as is the ignition system seals and a cross section of the igniter. The configuration of all internal nozzle joints is shown.

Aeromechanical stability of a hingeless rotor in hover and forward flight: Analysis and wind tunnel tests

NASA Technical Reports Server (NTRS)

Yeager, W. T., Jr.; Hamouda, M. N. H.; Mantay, W. R.

1983-01-01

A research effort of analysis and testing was conducted to investigate the ground resonance phenomenon of a soft in-plane hingeless rotor. Experimental data were obtained using a 9 ft. (2.74 m) diameter model rotor in hover and forward flight. Eight model rotor configurations were investigated. Configuration parameters included pitch flap coupling, blade sweep and droop, and precone of the blade feathering axis. An analysis based on a comprehensive analytical model of rotorcraft aerodynamics and dynamics was used. The moving block was used to experimentally determine the regressing lead lag mode damping. Good agreement was obtained between the analysis and test. Both analysis and experiment indicated ground resonance instability in hover. An outline of the analysis, a description of the experimental model and procedures, and comparison of the analytical and experimental data are presented.

Automatic analysis for neuron by confocal laser scanning microscope

NASA Astrophysics Data System (ADS)

Satou, Kouhei; Aoki, Yoshimitsu; Mataga, Nobuko; Hensh, Takao K.; Taki, Katuhiko

2005-12-01

The aim of this study is to develop a system that recognizes both the macro- and microscopic configurations of nerve cells and automatically performs the necessary 3-D measurements and functional classification of spines. The acquisition of 3-D images of cranial nerves has been enabled by the use of a confocal laser scanning microscope, although the highly accurate 3-D measurements of the microscopic structures of cranial nerves and their classification based on their configurations have not yet been accomplished. In this study, in order to obtain highly accurate measurements of the microscopic structures of cranial nerves, existing positions of spines were predicted by the 2-D image processing of tomographic images. Next, based on the positions that were predicted on the 2-D images, the positions and configurations of the spines were determined more accurately by 3-D image processing of the volume data. We report the successful construction of an automatic analysis system that uses a coarse-to-fine technique to analyze the microscopic structures of cranial nerves with high speed and accuracy by combining 2-D and 3-D image analyses.

Ultrasound beam characteristics of a symmetric nodal origami based array

NASA Astrophysics Data System (ADS)

Bilgunde, Prathamesh N.; Bond, Leonard J.

2018-04-01

Origami-the ancient art of paper folding-is being explored in acoustics for effective focusing of sound. In this short communication, we present a numerical investigation of beam characteristics for an origami based ultrasound array. A spatial re-configuration of array elements is performed based upon the symmetric nodal origami. The effect of fold angle on the ultrasound beam is evaluated using frequency domain and transient finite element analysis. It was found that increase in the fold angle reduces near field length by 58% and also doubles the beam intensity as compared to the linear array. Transient analysis also indicated 80% reduction in the -6dB beam width, which can improve the lateral resolution of phased array. Such a spatially re-configurable array could potentially be used in the future to reduce the cost of electronics in the phased array instrumentation.

Infrared Emission by an Aerosol Cloud.

DTIC Science & Technology

1980-10-10

contained in this report are those of the __j author(s) and should not be construed as an official Dep’artment of the Army ~ position, policy, or decision ...configuration employing a 4 inch diameter exhaust hose and auxillary fan located outside the hood has proved effective. Arrangements involving cone-shaped

Combustion Stability of the Gas Generator Assembly from J-2X Engine E10001 and Powerpack Tests

NASA Technical Reports Server (NTRS)

Hulka, J. R.; Kenny, R. L.; Casiano, M. J.

2013-01-01

Testing of a powerpack configuration (turbomachinery and gas generator assembly) and the first complete engine system of the liquid oxygen/liquid hydrogen propellant J-2X rocket engine have been completed at the NASA Stennis Space Center. The combustion stability characteristics of the gas generator assemblies on these two systems are of interest for reporting since considerable effort was expended to eliminate combustion instability during early development of the gas generator assembly with workhorse hardware. Comparing the final workhorse gas generator assembly development test data to the powerpack and engine system test data provides an opportunity to investigate how the nearly identical configurations of gas generator assemblies operate with two very different propellant supply systems one the autonomous pressure-fed test configuration on the workhorse development test stand, the other the pump-fed configurations on the powerpack and engine systems. The development of the gas generator assembly and the elimination of the combustion instability on the pressure-fed workhorse test stand have been reported extensively in the two previous Liquid Propulsion Subcommittee meetings 1-7. The powerpack and engine system testing have been conducted from mid-2011 through 2012. All tests of the powerpack and engine system gas generator systems to date have been stable. However, measureable dynamic behavior, similar to that observed on the pressure-fed test stand and reported in Ref. [6] and attributed to an injection-coupled response, has appeared in both powerpack and engine system tests. As discussed in Ref. [6], these injection-coupled responses are influenced by the interaction of the combustion chamber with a branch pipe in the hot gas duct that supplies gaseous helium to pre-spin the turbine during the start transient. This paper presents the powerpack and engine system gas generator test data, compares these data to the development test data, and provides additional combustion stability analyses of the configurations.

Rapid Detection & Identification of Bacillus Species using MALDI-TOF/TOF and Biomarker Database

DTIC Science & Technology

2006-06-01

rRNA sequence analysis. Multilocus enzyme electrophoresis ( MEE ) and comparative DNA sequence analysis suggest that they may represent a single species...adaptation of the MEE method [63] but with greater discrimination [64]. All of these new PCR-based subtyping methods are certainly superior and more...Demirev, P.A., Lin, J.S., Pineda , F.J., and Fenselau, C. (2001). Bioinformatics and mass spectrometry for microorganism identification: proteome-wide

Analysis of spatial configuration of the Palace Museum: an application of the axial-based space syntax

NASA Astrophysics Data System (ADS)

Chen, Jie; Lu, Feng

2006-10-01

Movement in a spatial system is produced and determined by the structure of the complex space itself, rather than special attractors within the whole spatial system. Based on this theory of space syntax, tourists' convergence and dispersal in the Palace Museum should be originated by the distribution of the internal constructions form. This article presents an application of the space syntax approach to the Palace Museum. After analyzing its internal spatial configuration, as a conclusion, the paper provides some rational advices so as to facilitate tourists as well as protect our invaluable cultural heritage.

Specific Abilities May Increment Psychometric g for High Ability Populations

DTIC Science & Technology

2016-04-14

tend to sort themselves into jobs that are commensurate with their ability level ( McCormick , DeNisi, & Staw, 1979; McCormick , Jeanneret, & Mecham...of Genetic Psychology, 153, 229-230. Specific abilities, g, & high ability populations 14 McCormick , E. J., DeNisi, A. S., & Shaw, J. B... McCormick , E. J., Jeanneret, P. R., & Mecham, R. C. (1972). A study of job characteristics and job dimensions as based on the Position Analysis Questionnaire

Psychophysical Bases for the Sensory Assessment of Rations

DTIC Science & Technology

1984-09-01

fragrant Fragrant, minty, fruity Floral, citrusy Floral, citrusy Heavy citrus, very fragrant Spicy, fruity, woody Spicy, fruity, woody Heavy, jasmine ...strawberry pomance essence . J. Food Sei., 41, 45 (1980). ^l^D.B. ^in an(j E.L. Thomas. Application of response surface analysis in the formulation of...Sehen, M.W. Montgomery, and L.M. Libbey. Subjective and optimum evaluation of strawberry pomance essence . J. Food Sei., 41, 45 (1980). 412. D.B. Min

Abnormal rsFC and GMV changes in parahippocampal and DLPFC for high Déjà vu experienced subjects.

PubMed

Qiu, Jiang; Xia, Yunman; He, Li; Chen, Qunlin; Sang, Na; Liu, Wei; Li, Hong

2018-03-01

How déjà vu works has long been a mystery, partially because of its characteristics of unpredictable occurrences and quick disappearances, which make it difficult to be explored. Previous studies have described the anatomical structures underlying déjà vu in healthy subjects; however, the functional mechanism of déjà vu remains unclear. Therefore, this study investigated the brain structural and functional components underlying déjà vu by combining voxel-based morphometry analysis (VBM) with resting-state functional connectivity (rsFC). The VBM analysis revealed that the anterior parahippocampal gyrus (PHG) had significantly less grey matter volume (GMV) in high déjà vu group than low group, confirming previous studies. Further functional connectivity analysis revealed that the frequency of déjà vu experiences was negatively correlated with the strength of the rsFC between anterior dorsal lateral prefrontal cortex (DLPFC) and anterior PHG but positively correlated with the strength of the rsFC between posterior DLPFC and posterior PHG. Moreover, the frequency of déjà vu experiences was negatively correlated with the strength of the rsFC between the anterior and posterior regions of the PHG. These findings indicated that familiarity without recollection (PHG) and superior context monitoring (DLPFC) are critical for real-life déjà vu experiences. Copyright © 2018 Elsevier B.V. All rights reserved.

A graph-based network-vulnerability analysis system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swiler, L.P.; Phillips, C.; Gaylor, T.

1998-05-03

This paper presents a graph based approach to network vulnerability analysis. The method is flexible, allowing analysis of attacks from both outside and inside the network. It can analyze risks to a specific network asset, or examine the universe of possible consequences following a successful attack. The analysis system requires as input a database of common attacks, broken into atomic steps, specific network configuration and topology information, and an attacker profile. The attack information is matched with the network configuration information and an attacker profile to create a superset attack graph. Nodes identify a stage of attack, for example themore » class of machines the attacker has accessed and the user privilege level he or she has compromised. The arcs in the attack graph represent attacks or stages of attacks. By assigning probabilities of success on the arcs or costs representing level of effort for the attacker, various graph algorithms such as shortest path algorithms can identify the attack paths with the highest probability of success.« less

A graph-based network-vulnerability analysis system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swiler, L.P.; Phillips, C.; Gaylor, T.

1998-01-01

This report presents a graph-based approach to network vulnerability analysis. The method is flexible, allowing analysis of attacks from both outside and inside the network. It can analyze risks to a specific network asset, or examine the universe of possible consequences following a successful attack. The analysis system requires as input a database of common attacks, broken into atomic steps, specific network configuration and topology information, and an attacker profile. The attack information is matched with the network configuration information and an attacker profile to create a superset attack graph. Nodes identify a stage of attack, for example the classmore » of machines the attacker has accessed and the user privilege level he or she has compromised. The arcs in the attack graph represent attacks or stages of attacks. By assigning probabilities of success on the arcs or costs representing level-of-effort for the attacker, various graph algorithms such as shortest-path algorithms can identify the attack paths with the highest probability of success.« less

Observation of a new charged charmoniumlike state in B ¯ 0 → J / ψ K - π + decays

DOE PAGES

Chilikin, K.; Mizuk, R.; Adachi, I.; ...

2014-12-16

We present the results of an amplitude analysis of B ¯0→J/ψK -π + decays. A new charged charmoniumlike state Z c(4200) + decaying to J/ψπ + is observed with a significance of 6.2σ. The mass and width of the Z c(4200) + are 4196 +31 -29 +17 -13 MeV/c 2 and 370 +70 -70 +70 -132 MeV, respectively; the preferred assignment of the quantum numbers is JP=1 +. In addition, we find evidence for Z c(4430) +→J/ψπ +. The analysis is based on a 711 fb -1 data sample collected by the Belle detector at the asymmetric-energy e +e -more » collider KEKB.« less

Tolerance for distorted faces: challenges to a configural processing account of familiar face recognition.

PubMed

Sandford, Adam; Burton, A Mike

2014-09-01

Face recognition is widely held to rely on 'configural processing', an analysis of spatial relations between facial features. We present three experiments in which viewers were shown distorted faces, and asked to resize these to their correct shape. Based on configural theories appealing to metric distances between features, we reason that this should be an easier task for familiar than unfamiliar faces (whose subtle arrangements of features are unknown). In fact, participants were inaccurate at this task, making between 8% and 13% errors across experiments. Importantly, we observed no advantage for familiar faces: in one experiment participants were more accurate with unfamiliars, and in two experiments there was no difference. These findings were not due to general task difficulty - participants were able to resize blocks of colour to target shapes (squares) more accurately. We also found an advantage of familiarity for resizing other stimuli (brand logos). If configural processing does underlie face recognition, these results place constraints on the definition of 'configural'. Alternatively, familiar face recognition might rely on more complex criteria - based on tolerance to within-person variation rather than highly specific measurement. Copyright © 2014 Elsevier B.V. All rights reserved.

Comparative analysis of imaging configurations and objectives for Fourier microscopy.

PubMed

Kurvits, Jonathan A; Jiang, Mingming; Zia, Rashid

2015-11-01

Fourier microscopy is becoming an increasingly important tool for the analysis of optical nanostructures and quantum emitters. However, achieving quantitative Fourier space measurements requires a thorough understanding of the impact of aberrations introduced by optical microscopes that have been optimized for conventional real-space imaging. Here we present a detailed framework for analyzing the performance of microscope objectives for several common Fourier imaging configurations. To this end, we model objectives from Nikon, Olympus, and Zeiss using parameters that were inferred from patent literature and confirmed, where possible, by physical disassembly. We then examine the aberrations most relevant to Fourier microscopy, including the alignment tolerances of apodization factors for different objective classes, the effect of magnification on the modulation transfer function, and vignetting-induced reductions of the effective numerical aperture for wide-field measurements. Based on this analysis, we identify an optimal objective class and imaging configuration for Fourier microscopy. In addition, the Zemax files for the objectives and setups used in this analysis have been made publicly available as a resource for future studies.

Spectroscopic detection of biological NO with a quantum cascade laser

NASA Technical Reports Server (NTRS)

Menzel, L.; Kosterev, A. A.; Curl, R. F.; Tittel, F. K.; Gmachl, C.; Capasso, F.; Sivco, D. L.; Baillargeon, J. N.; Hutchinson, A. L.; Cho, A. Y.;